WorldWideScience

Sample records for waste minimization promotes

  1. Waste minimization promotes biophysical treatment of complex petrochemical wastes in Israel

    Energy Technology Data Exchange (ETDEWEB)

    Lebel, A. [Invirotreat International Ltd., Fulleron, CA (United States); Raveh, A. [Raveh Ecology Ltd., Haifa (Israel)

    1993-12-31

    This work describes a full-scale waste treatment system which was put into operation in a petrochemical manufacturing plant in Israel for the purpose of detoxifying its complex organic waste stream. The treatment plant design incorporates an innovative waste management approach to accommodate the limited space allocated for the facility. Initial performance data indicate a high efficient inorganic waste reduction. 4 refs., 6 figs., 2 tabs.

  2. Waste minimization handbook, Volume 1

    Energy Technology Data Exchange (ETDEWEB)

    Boing, L.E.; Coffey, M.J.

    1995-12-01

    This technical guide presents various methods used by industry to minimize low-level radioactive waste (LLW) generated during decommissioning and decontamination (D and D) activities. Such activities generate significant amounts of LLW during their operations. Waste minimization refers to any measure, procedure, or technique that reduces the amount of waste generated during a specific operation or project. Preventive waste minimization techniques implemented when a project is initiated can significantly reduce waste. Techniques implemented during decontamination activities reduce the cost of decommissioning. The application of waste minimization techniques is not limited to D and D activities; it is also useful during any phase of a facility`s life cycle. This compendium will be supplemented with a second volume of abstracts of hundreds of papers related to minimizing low-level nuclear waste. This second volume is expected to be released in late 1996.

  3. Waste minimization and pollution prevention awareness plan

    Energy Technology Data Exchange (ETDEWEB)

    1991-05-31

    The purpose of this plan is to document the Lawrence Livermore National Laboratory (LLNL) Waste Minimization and Pollution Prevention Awareness Program. The plan specifies those activities and methods that are or will be employed to reduce the quantity and toxicity of wastes generated at the site. The intent of this plan is to respond to and comply with (DOE's) policy and guidelines concerning the need for pollution prevention. The Plan is composed of a LLNL Waste Minimization and Pollution Prevention Awareness Program Plan and, as attachments, Program- and Department-specific waste minimization plans. This format reflects the fact that waste minimization is considered a line management responsibility and is to be addressed by each of the Programs and Departments. 14 refs.

  4. Utilization of biocatalysts in cellulose waste minimization

    Energy Technology Data Exchange (ETDEWEB)

    Woodward, J.; Evans, B.R.

    1996-09-01

    Cellulose, a polymer of glucose, is the principal component of biomass and, therefore, a major source of waste that is either buried or burned. Examples of biomass waste include agricultural crop residues, forestry products, and municipal wastes. Recycling of this waste is important for energy conservation as well as waste minimization and there is some probability that in the future biomass could become a major energy source and replace fossil fuels that are currently used for fuels and chemicals production. It has been estimated that in the United States, between 100-450 million dry tons of agricultural waste are produced annually, approximately 6 million dry tons of animal waste, and of the 190 million tons of municipal solid waste (MSW) generated annually, approximately two-thirds is cellulosic in nature and over one-third is paper waste. Interestingly, more than 70% of MSW is landfilled or burned, however landfill space is becoming increasingly scarce. On a smaller scale, important cellulosic products such as cellulose acetate also present waste problems; an estimated 43 thousand tons of cellulose ester waste are generated annually in the United States. Biocatalysts could be used in cellulose waste minimization and this chapter describes their characteristics and potential in bioconversion and bioremediation processes.

  5. Waste Minimization Program. Air Force Plant 4.

    Science.gov (United States)

    1986-02-01

    calculation of makeup requirements. 4. Coolant Recovery System. A centralized system for coolant recovery and reuse will employ a centrifugation system...acceptor and _ metal stabilizers. A maximum reuse program of this type would require additional solvent analyses to determine the necessary additive makeup ...34". OPERATOR:•6t DATE:" WASTE MINIMIZATION PROGRAM " DATA SHEET .. WAST"ES "- CHARACTERISTICS: . -.4 )/7YI. .7"R--e: e&-0l,)" fx ,/’-Z 𔄁S" (ATTACH ANALYSIS IF

  6. Hazardous Waste Minimization Assessment: Fort Meade, MD

    Science.gov (United States)

    1991-01-01

    such as naptha. xylene, toluene, or hexane. Powder or water-based paints do not contain solvents. Solvent-based paints (e.g., acrylic lacquers) have the...W.H. Resy. ’Solvent Riocovery in the Paint Indust’y." Paints & Resin (March/April 1982). pp 41-44. SCS Engineers. Inc.. Waste A-.i Stdy • Ahomwive...They should also be located in such a way as to minimize patients/personnel exposure to the wastes. The containers must be cleaned and disinfected

  7. Cultural change and support of waste minimization

    Energy Technology Data Exchange (ETDEWEB)

    Boylan, M.S. [EG and G Idaho, Inc., Idaho Falls, ID (United States). Idaho National Engineering Lab.

    1991-12-31

    The process of bringing a subject like pollution prevention to top of mind awareness, where designed to prevent waste becomes part of business as usual, is called cultural change. With Department of Energy orders and management waste minimization commitment statements on file, the REAL work is just beginning at the Idaho National Engineering Laboratory (INEL); shaping the attitudes of 11,000+ employees. The difficulties of such a task are daunting. The 890 square mile INEL site and in-town support offices mean a huge diversity of employee jobs and waste streams; from cafeteria and auto maintenance wastes to high-level nuclear waste casks. INEL is pursuing a three component cultural change strategy: training, publicity, and public outreach. To meet the intent of DOE orders, all INEL employees are slated to receive pollution prevention orientation training. More technical training is given to targeted groups like purchasing and design engineering. To keep newly learned pollution prevention concepts top-of-mind, extensive site-wide publicity is being developed and conducted, culminating in the April Pollution Prevention Awareness Week coinciding with Earth Day 1992. Finally, news of INEL pollution prevention successes is shared with the public to increase their overall environmental awareness and their knowledge of INEL activities. An important added benefit is the sense of pride the program instills in INEL employees to have their successes displayed so publicly.

  8. Waste Minimization and Pollution Prevention Awareness Plan

    Energy Technology Data Exchange (ETDEWEB)

    1994-04-01

    The purpose of this plan is to document Lawrence Livermore National Laboratory (LLNL) projections for present and future waste minimization and pollution prevention. The plan specifies those activities and methods that are or will be used to reduce the quantity and toxicity of wastes generated at the site. It is intended to satisfy Department of Energy (DOE) requirements. This Plan provides an overview of projected activities from FY 1994 through FY 1999. The plans are broken into site-wide and problem-specific activities. All directorates at LLNL have had an opportunity to contribute input, to estimate budget, and to review the plan. In addition to the above, this plan records LLNL`s goals for pollution prevention, regulatory drivers for those activities, assumptions on which the cost estimates are based, analyses of the strengths of the projects, and the barriers to increasing pollution prevention activities.

  9. Waste minimization in the oil and gas industries

    Energy Technology Data Exchange (ETDEWEB)

    Smith, K.P.

    1992-09-01

    Recent legislative actions place an emphasis on waste minimization as opposed to traditional end-of-pipe waste management. This new philosophy, coupled with increasing waste disposal costs and associated liabilities, sets the stage for investigating waste minimization opportunities in all industries wastes generated by oil and gas exploration and production (E&P) and refuting activities are regulated as non-hazardous under the Resource Conservation and Recovery Act (RCRA). Potential reclassification of these wastes as hazardous would make minimization of these waste streams even more desirable. Oil and gas E&P activities generate a wide variety of wastes, although the bulk of the wastes (98%) consists of a single waste stream: produced water. Opportunities to minimize E&P wastes through point source reduction activities are limited by the extractive nature of the industry. Significant waste minimization is possible, however, through recycling. Recycling activities include underground injection of produced water, use of closed-loop drilling systems, reuse of produced water and drilling fluids in other oilfield activities, use of solid debris as construction fill, use of oily wastes as substitutes for road mix and asphalt, landspreading of produced sand for soil enhancement, and roadspreading of suitable aqueous wastes for dust suppression or deicing. Like the E&P wastes, wastes generated by oil and gas treatment and refining activities cannot be reduced substantially at the point source but can be reduced through recycling. For the most part, extensive recycling and reprocessing of many waste streams already occurs at most petroleum refineries. A variety of innovative waste treatment activities have been developed to minimize the toxicity or volume of oily wastes generated by both E&P and refining activities. These treatments include bioremediation, oxidation, biooxidation, incineration, and separation. Application of these treatment processes is still limited.

  10. Waste minimization in the oil and gas industries

    Energy Technology Data Exchange (ETDEWEB)

    Smith, K.P.

    1992-01-01

    Recent legislative actions place an emphasis on waste minimization as opposed to traditional end-of-pipe waste management. This new philosophy, coupled with increasing waste disposal costs and associated liabilities, sets the stage for investigating waste minimization opportunities in all industries wastes generated by oil and gas exploration and production (E P) and refuting activities are regulated as non-hazardous under the Resource Conservation and Recovery Act (RCRA). Potential reclassification of these wastes as hazardous would make minimization of these waste streams even more desirable. Oil and gas E P activities generate a wide variety of wastes, although the bulk of the wastes (98%) consists of a single waste stream: produced water. Opportunities to minimize E P wastes through point source reduction activities are limited by the extractive nature of the industry. Significant waste minimization is possible, however, through recycling. Recycling activities include underground injection of produced water, use of closed-loop drilling systems, reuse of produced water and drilling fluids in other oilfield activities, use of solid debris as construction fill, use of oily wastes as substitutes for road mix and asphalt, landspreading of produced sand for soil enhancement, and roadspreading of suitable aqueous wastes for dust suppression or deicing. Like the E P wastes, wastes generated by oil and gas treatment and refining activities cannot be reduced substantially at the point source but can be reduced through recycling. For the most part, extensive recycling and reprocessing of many waste streams already occurs at most petroleum refineries. A variety of innovative waste treatment activities have been developed to minimize the toxicity or volume of oily wastes generated by both E P and refining activities. These treatments include bioremediation, oxidation, biooxidation, incineration, and separation. Application of these treatment processes is still limited.

  11. Cradle-to-cradle stewardship of drugs for minimizing their environmental disposition while promoting human health. II. Drug disposal, waste reduction, and future directions.

    Science.gov (United States)

    Daughton, Christian G

    2003-05-01

    Since the 1980s, the occurrence of pharmaceuticals and personal care products (PPCPs) as trace environmental pollutants, originating primarily from consumer use and actions rather than manufacturer effluents, continues to become more firmly established. The growing, worldwide importance of freshwater resources underscores the need for ensuring that any aggregate or cumulative impacts on (or from) water supplies are minimized. Despite a paucity of effects data from long-term, simultaneous exposure at low doses to multiple xenobiotics (particularly non-target-organism exposure to PPCPs), a wide range of proactive actions could be implemented for reducing or minimizing the introduction of PPCPs to the environment. Most of these actions fall under what could be envisioned as a holistic stewardship program--overseen by the health care industry and consumers alike. Significantly, such a stewardship program would benefit not just the environment--additional, collateral benefits could automatically accrue, including the lessening of medication expense for the consumer and improving patient health and consumer safety. In this article (the second of two parts describing the "green pharmacy") I focus on those actions and activities tied more closely to the end user (e.g., the patient) and issues associated with drug disposal/recycling that could prove useful in minimizing the environmental disposition of PPCPs. I also outline some recommendations and suggestions for further research and pose some considerations regarding the future. In this mini-monograph I attempt to capture cohesively for the first time the wide spectrum of actions available for minimizing the release of PPCPs to the environment. A major objective is to generate an active dialog or debate across the many disciplines that must become actively involved to design and implement a successful approach to life-cycle stewardship of PPCPs.

  12. The Construction Solid Waste Minimization Practices among Malaysian Contractors

    Directory of Open Access Journals (Sweden)

    Che Ahmad A.

    2014-01-01

    Full Text Available The function of minimization of construction solid waste is to reduce or eliminates the adverse impacts on the environment and to human health. Due to the increase of population that leads to rapid development, there are possibilities of construction solid waste to be increased shortly from the construction works, demolition or renovation works. Materials such as wood, concrete, paint, brick, roofing, tiles, plastic and any other materials would contribute problem involving construction solid waste. Therefore, the proper waste minimization is needed to control the quantity of construction solid waste produced. This paper identifies the type of construction solid waste produced and discusses the waste minimization practice by the contractors at construction sites in Selangor, Kuala Lumpur and Putrajaya, Malaysia.

  13. Hazardous-waste minimization assessment: Fort Campbell, Kentucky. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Dharmavaram, S.; Knowlton, D.A.; Heflin, C.; Donahue, B.A.

    1991-03-01

    Waste minimization is the process of reducing the net outflow of hazardous materials that may be solid, liquid, or gaseous effluents from a given source or generating process. It involves reducing air pollution emissions, contamination of surface and ground water, and land disposal by means of source reduction, waste recycling processes, and treatment leading to complete destruction. Among Federal regulations is a requirement that every generator of hazardous wastes producing in excess of 2205 pounds per month certify that a hazardous waste minimization program is in operation. Generators are required to submit biennial reports to the USEPA that describe efforts taken to reduce the volume and toxicity of waste generated during the year. The objective of this research was to develop a hazardous waste minimization plan for Fort Campbell, Kentucky, to include actions necessary to reduce the generation of hazardous wastes. Reduction should be in both volume and toxicity.

  14. Food waste minimization from a life-cycle perspective.

    Science.gov (United States)

    Bernstad Saraiva Schott, A; Andersson, T

    2015-01-01

    This article investigates potentials and environmental impacts related to household food waste minimization, based on a case study in Southern Sweden. In the study, the amount of avoidable and unavoidable food waste currently being disposed of by households was assessed through waste composition analyses and the different types of avoidable food waste were classified. Currently, both avoidable and unavoidable food waste is either incinerated or treated through anaerobic digestion. A hypothetical scenario with no generation of avoidable food waste and either anaerobic digestion or incineration of unavoidable food waste was compared to the current situation using the life-cycle assessment method, limited to analysis of global warming potential (GWP). The results from the waste composition analyses indicate that an average of 35% of household food waste is avoidable. Minimization of this waste could result in reduction of greenhouse gas emissions of 800-1400 kg/tonne of avoidable food waste. Thus, a minimization strategy would result in increased avoidance of GWP compared to the current situation. The study clearly shows that although modern alternatives for food waste treatment can result in avoidance of GWP through nutrient and energy recovery, food waste prevention yields far greater benefits for GWP compared to both incineration and anaerobic digestion. Copyright © 2014 Elsevier Ltd. All rights reserved.

  15. 2016 Los Alamos National Laboratory Hazardous Waste Minimization Report

    Energy Technology Data Exchange (ETDEWEB)

    Salzman, Sonja L. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); English, Charles Joe [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2016-12-02

    Waste minimization and pollution prevention are goals within the operating procedures of Los Alamos National Security, LLC (LANS). The US Department of Energy (DOE), inclusive of the National Nuclear Security Administration (NNSA) and the Office of Environmental Management, and LANS are required to submit an annual hazardous waste minimization report to the New Mexico Environment Department (NMED) in accordance with the Los Alamos National Laboratory (LANL or the Laboratory) Hazardous Waste Facility Permit. The report was prepared pursuant to the requirements of Section 2.9 of the LANL Hazardous Waste Facility Permit. This report describes the hazardous waste minimization program, which is a component of the overall Pollution Prevention (P2) Program, administered by the Environmental Stewardship Group (EPC-ES). This report also supports the waste minimization and P2 goals of the Associate Directorate of Environmental Management (ADEM) organizations that are responsible for implementing remediation activities and describes its programs to incorporate waste reduction practices into remediation activities and procedures. This report includes data for all waste shipped offsite from LANL during fiscal year (FY) 2016 (October 1, 2015 – September 30, 2016). LANS was active during FY2016 in waste minimization and P2 efforts. Multiple projects were funded that specifically related to reduction of hazardous waste. In FY2016, there was no hazardous, mixed-transuranic (MTRU), or mixed low-level (MLLW) remediation waste shipped offsite from the Laboratory. More non-remediation hazardous waste and MLLW was shipped offsite from the Laboratory in FY2016 compared to FY2015. Non-remediation MTRU waste was not shipped offsite during FY2016. These accomplishments and analysis of the waste streams are discussed in much more detail within this report.

  16. 2013 Los Alamos National Laboratory Hazardous Waste Minimization Report

    Energy Technology Data Exchange (ETDEWEB)

    Salzman, Sonja L. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); English, Charles J. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2015-08-24

    Waste minimization and pollution prevention are inherent goals within the operating procedures of Los Alamos National Security, LLC (LANS). The US Department of Energy (DOE) and LANS are required to submit an annual hazardous waste minimization report to the New Mexico Environment Department (NMED) in accordance with the Los Alamos National Laboratory (LANL or the Laboratory) Hazardous Waste Facility Permit. The report was prepared pursuant to the requirements of Section 2.9 of the LANL Hazardous Waste Facility Permit. This report describes the hazardous waste minimization program (a component of the overall Waste Minimization/Pollution Prevention [WMin/PP] Program) administered by the Environmental Stewardship Group (ENV-ES). This report also supports the waste minimization and pollution prevention goals of the Environmental Programs Directorate (EP) organizations that are responsible for implementing remediation activities and describes its programs to incorporate waste reduction practices into remediation activities and procedures. LANS was very successful in fiscal year (FY) 2013 (October 1-September 30) in WMin/PP efforts. Staff funded four projects specifically related to reduction of waste with hazardous constituents, and LANS won four national awards for pollution prevention efforts from the National Nuclear Security Administration (NNSA). In FY13, there was no hazardous, mixedtransuranic (MTRU), or mixed low-level (MLLW) remediation waste generated at the Laboratory. More hazardous waste, MTRU waste, and MLLW was generated in FY13 than in FY12, and the majority of the increase was related to MTRU processing or lab cleanouts. These accomplishments and analysis of the waste streams are discussed in much more detail within this report.

  17. Waste Minimization Policy at the Romanian Nuclear Power Plant

    Energy Technology Data Exchange (ETDEWEB)

    Andrei, V.; Daian, I.

    2002-02-26

    The radioactive waste management system at Cernavoda Nuclear Power Plant (NPP) in Romania was designed to maintain acceptable levels of safety for workers and to protect human health and the environment from exposure to unacceptable levels of radiation. In accordance with terminology of the International Atomic Energy Agency (IAEA), this system consists of the ''pretreatment'' of solid and organic liquid radioactive waste, which may include part or all of the following activities: collection, handling, volume reduction (by an in-drum compactor, if appropriate), and storage. Gaseous and aqueous liquid wastes are managed according to the ''dilute and discharge'' strategy. Taking into account the fact that treatment/conditioning and disposal technologies are still not established, waste minimization at the source is a priority environmental management objective, while waste minimization at the disposal stage is presently just a theoretical requirement for future adopted technologies . The necessary operational and maintenance procedures are in place at Cernavoda to minimize the production and contamination of waste. Administrative and technical measures are established to minimize waste volumes. Thus, an annual environmental target of a maximum 30 m3 of radioactive waste volume arising from operation and maintenance has been established. Within the first five years of operations at Cernavoda NPP, this target has been met. The successful implementation of the waste minimization policy has been accompanied by a cost reduction while the occupational doses for plant workers have been maintained at as low as reasonably practicable levels. This paper will describe key features of the waste management system along with the actual experience that has been realized with respect to minimizing the waste volumes at the Cernavoda NPP.

  18. WASTE MINIMIZATION PRACTICES AT TWO CCA WOOD TREATMENT PLANTS

    Science.gov (United States)

    Two chromated copper arsenate (CCA) wood-treatment plants were assessed for their waste minimization practices. These practices have been reflected in several areas, including facility designs, process controls, and management practices. he objectives were to estimate the amount...

  19. Cleaner production: Minimizing hazardous waste in Indonesia

    Energy Technology Data Exchange (ETDEWEB)

    Bratasida, D.L. [BAPEDAL, Jakarta (Indonesia)

    1996-12-31

    In the second long-term development plan, industry plays a significant role in economic growth. In Indonesia, industries grow very fast; such fast growth can adversely effect the environment. Exploitation of assets can mean depletion of natural resources and energy, which, if incorrectly managed, can endanger human life and the environment. The inefficient use of natural resources will accelerate their exhaustion and generate pollution, resulting in environmental damage and threats to economic development and human well being. In recent years, changes in the approach used to control pollution have been necessary because of the increasing seriousness of the problems. Initial environmental management strategies were based on a carrying capacity approach; the natural assimilative capacity accommodated the pollution load that was applied. The environmental management strategies adopted later included technologies applied to the end of the discharge point (so-called {open_quotes}end-of-pipe{close_quotes} treatments). Until now, environmental management strategies focused on end-of-pipe approaches that control pollutants after they are generated. These approaches concentrate on waste treatment and disposal to control pollution and environmental degradation. However, as industry develops, waste volumes continue to increase, thereby creating further environmental problems. In addition, the wastes produced tend to have more complex characteristics and are potentially more difficult to treat for a reasonable cost. There are often technical and financial obstacles to regulatory compliance if waste treatment is relied on as the only means of achieving environmental objectives. Consequently, the reactive end-of-pipe treatment approach has been changed to a proactive cleaner production approach. This approach is based on the concept of sustainable development and is designed to prevent pollution as well as to protect natural resources and the quality of the environment.

  20. Waste minimization in a petrochemical company

    Energy Technology Data Exchange (ETDEWEB)

    Anan, Marcelo [Oxiteno S.A., Industria e Comercio, Sao Paulo, SP (Brazil)

    1993-12-31

    A way to manage industrial effluents consists in reducing their generation or treating them when elimination or minimization is economically unachievable. This work aims to present the modifications adopted in a petrochemical plant to adequate and, or, reduce the generation of industrial effluent. 8 refs., 3 figs.

  1. Adoption of waste minimization technology to benefit electroplaters

    Energy Technology Data Exchange (ETDEWEB)

    Ching, E.M.K.; Li, C.P.H.; Yu, C.M.K. [Hong Kong Productivity Council, Kowloon (Hong Kong)

    1996-12-31

    Because of increasingly stringent environmental legislation and enhanced environmental awareness, electroplaters in Hong Kong are paying more heed to protect the environment. To comply with the array of environmental controls, electroplaters can no longer rely solely on the end-of-pipe approach as a means for abating their pollution problems under the particular local industrial environment. The preferred approach is to adopt waste minimization measures that yield both economic and environmental benefits. This paper gives an overview of electroplating activities in Hong Kong, highlights their characteristics, and describes the pollution problems associated with conventional electroplating operations. The constraints of using pollution control measures to achieve regulatory compliance are also discussed. Examples and case studies are given on some low-cost waste minimization techniques readily available to electroplaters, including dragout minimization and water conservation techniques. Recommendations are given as to how electroplaters can adopt and exercise waste minimization techniques in their operations. 1 tab.

  2. Good Practice Guide Waste Minimization/Pollution Prevention

    Energy Technology Data Exchange (ETDEWEB)

    J Dorsey

    1999-10-14

    This Good Practice Guide provides tools, information, and examples for promoting the implementation of pollution prevention during the design phases of U.S. Department of Energy (DOE) projects. It is one of several Guides for implementing DOE Order 430.1, Life-cycle Asset Management. DOE Order 430.1 provides requirements for DOE, in partnership with its contractors, to plan, acquire, operate, maintain, and dispose of physical assets. The goals of designing for pollution prevention are to minimize raw material consumption, energy consumption, waste generation, health and safety impacts, and ecological degradation over the entire life of the facility (EPA 1993a). Users of this Guide will learn to translate national policy and regulatory requirements for pollution prevention into action at the project level. The Guide was written to be applicable to all DOE projects, regardless of project size or design phase. Users are expected to interpret the Guide for their individual project's circumstances, applying a graded approach so that the effort is consistent with the anticipated waste generation and resource consumption of the physical asset. This Guide employs a combination of pollution prevention opportunity assessment (PPOA) methods and design for environment (DfE) philosophies. The PPOA process was primarily developed for existing products, processes, and facilities. The PPOA process has been modified in this Guide to address the circumstances of the DOE design process as delineated in DOE Order 430.1 and its associated Good Practice Guides. This modified form of the PPOA is termed the Pollution Prevention Design Assessment (P2DA). Information on current nationwide methods and successes in designing for the environment also have been reviewed and are integrated into this guidance.

  3. Waste Minimization/Pollution Prevention Crosscut Plan, 1994

    Energy Technology Data Exchange (ETDEWEB)

    1994-02-28

    This plan establishes a Department-wide goal to reduce total releases of toxic chemicals to the environment and off-site transfers of such toxic chemicals by 50 percent by December 31, 1999, in compliance with Executive Order 12856. Each site that meets the threshold quantities of toxic chemicals established in the Emergency Planning and Community Right-to-Know Act (EPCRA) will participate in this goal. In addition, each DOE site will establish site-specific goals to reduce generation of hazardous, radioactive, radioactive mixed, and sanitary wastes and pollutants, as applicable. Implementation of this plan will represent a major step toward the environmental risks and costs associated with DOE operations and increasing the Department`s use of preventive environmental management practices. Investing in Waste Minimization Pollution Prevention (WMin/PP) steadily reduce hazardous and radioactive waste generation and will reduce the need for waste management and unnecessary expenditures for waste treatment, storage, and disposal. A preventive approach to waste management will help solve current environmental and regulatory issues and reduce the need for costly future corrective actions. The purpose of this plan is to establish the strategic framework for integrating WMin/PP into all DOE internal activities. This program includes setting DOE policy and goals for reducing the generation of wastes and pollutants, increasing recycling activities, and establishing an infrastructure to achieve and measure the goals throughout the DOE complex. Waste Minimization and Pollution Prevention Awareness Plans, submitted to Headquarters by DOE field sites, will incorporate the WMin/PP activities and goals outlined in this plan. Success of the DOE WMin/PP program is dependent upon each field operation becoming accountable for resources used, wastes and pollutants generated, and wastes recycled.

  4. Mixed low-level waste minimization at Los Alamos

    Energy Technology Data Exchange (ETDEWEB)

    Starke, T.P.

    1998-12-01

    During the first six months of University of California 98 Fiscal Year (July--December) Los Alamos National Laboratory has achieved a 57% reduction in mixed low-level waste generation. This has been accomplished through a systems approach that identified and minimized the largest MLLW streams. These included surface-contaminated lead, lead-lined gloveboxes, printed circuit boards, and activated fluorescent lamps. Specific waste minimization projects have been initiated to address these streams. In addition, several chemical processing equipment upgrades are being implemented. Use of contaminated lead is planned for several high energy proton beam stop applications and stainless steel encapsulated lead is being evaluated for other radiological control area applications. INEEL is assisting Los Alamos with a complete systems analysis of analytical chemistry derived mixed wastes at the CMR building and with a minimum life-cycle cost standard glovebox design. Funding for waste minimization upgrades has come from several sources: generator programs, waste management, the generator set-aside program, and Defense Programs funding to INEEL.

  5. Annual Report on Waste Generation and Waste Minimization Progress, 1991--1992

    Energy Technology Data Exchange (ETDEWEB)

    1994-02-01

    This report is DOE`s first annual report on waste generation and waste minimization progress. Data presented in this report were collected from all DOE sites which met minimum threshold criteria established for this report. The fifty-seven site submittals contained herein represent data from over 100 reporting sites within 25 states. Radioactive, hazardous and sanitary waste quantities and the efforts to minimize these wastes are highlighted within the fifty-seven site submittals. In general, sites have made progress in moving beyond the planning phase of their waste minimization programs. This is evident by the overall 28 percent increase in the total amount of materials recycled from 1991 to 1992, as well as individual site initiatives. During 1991 and 1992, DOE generated a total of 279,000 cubic meters of radioactive waste and 243,000 metric tons of non-radioactive waste. These waste amounts include significant portions of process wastewater required to be reported to regulatory agencies in the state of Texas and the state of Tennessee. Specifically, the Pantex Plant in Texas treats an industrial wastewater that is considered by the Texas Water Commission to be a hazardous waste. In 1992, State regulated wastewater from the Pantex Plant represented 3,620 metric tons, 10 percent of the total hazardous waste generated by DOE. Similarly, mixed low-level wastewater from the TSCA Incinerator Facility at the Oak Ridge K-25 Site in Tennessee represented 55 percent of the total radioactive waste generated by DOE in 1992.

  6. Waste minimization and pollution prevention awareness plan. Revision 1

    Energy Technology Data Exchange (ETDEWEB)

    1994-07-01

    The purpose of this plan is to document Lawrence Livermore National Laboratory (LLNL) projections for present and future waste minimization and pollution prevention. The plan specifies those activities and methods that are or will be used to reduce the quantity and toxicity of wastes generated at the site. It is intended to satisfy Department of Energy (DOE) requirements. This Waste Minimization and Pollution Prevention Awareness Plan provides an overview of projected activities from FY 1994 through FY 1999. The plans are broken into site-wide and problem-specific activities. All directorates at LLNL have had an opportunity to contribute input, estimate budgets, and review the plan. In addition to the above, this plan records LLNL`s goals for pollution prevention, regulatory drivers for those activities, assumptions on which the cost estimates are based, analyses of the strengths of the projects, and the barriers to increasing pollution prevention activities.

  7. Pollution prevention and waste minimization tools workshops: Proceedings. Part 2

    Energy Technology Data Exchange (ETDEWEB)

    1993-12-31

    The purpose of the second workshop was to bring together representatives of DOE and DOE contractor organizations to discuss four topics: process waste assessments (PWAs), a continuation of one of the sessions held at the first workshop in Clearwater; waste minimization reporting requirements; procurement systems for waste minimization; and heating, ventilating, and air conditioning (HVAC) and replacements for chlorofluorocarbons (CFCs). The topics were discussed in four concurrent group sessions. Participants in each group were encouraged to work toward achieving two main objectives: establish a ``clear vision`` of the overall target for their session`s program, focusing not just on where the program is now but on where it should go in the long term; and determine steps to be followed to carry out the target program.

  8. Low-level waste minimization at the Y-12 Plant

    Energy Technology Data Exchange (ETDEWEB)

    Koger, J. [Oak Ridge National Lab., TN (United States)

    1993-03-01

    The Y-12 Development Waste Minimization Program is used as a basis for defining new technologies and processes that produce minimum low-level wastes (hazardous, mixed, radioactive, and industrial) for the Y-12 Plant in the future and for Complex-21 and that aid in decontamination and decommissioning (D and D) efforts throughout the complex. In the past, the strategy at the Y-12 Plant was to treat the residues from the production processes using chemical treatment, incineration, compaction, and other technologies, which often generated copious quantities of additional wastes and, with the exception of highly valuable materials such as enriched uranium, incorporated very little recycle in the process. Recycle, in this context, is defined as material that is put back into the process before it enters a waste stream. Additionally, there are several new technology drivers that have recently emerged with the changing climate in the Nuclear Weapons Complex such as Complex 21 and D and D technologies and an increasing number of disassemblies. The hierarchies of concern in the waste minimization effort are source reduction, recycle capability, treatment simplicity, and final disposal difficulty with regard to Complex 21, disassembly efforts, D and D, and, to a lesser extent, weapons production. Source reduction can be achieved through substitution of hazardous substances for nonhazardous materials, and process changes that result in less generated waste.

  9. Using benchmarking to minimize common DOE waste streams. Volume 1, Methodology and liquid photographic waste

    Energy Technology Data Exchange (ETDEWEB)

    Levin, V.

    1994-04-01

    Finding innovative ways to reduce waste streams generated at Department of Energy (DOE) sites by 50% by the year 2000 is a challenge for DOE`s waste minimization efforts. This report examines the usefulness of benchmarking as a waste minimization tool, specifically regarding common waste streams at DOE sites. A team of process experts from a variety of sites, a project leader, and benchmarking consultants completed the project with management support provided by the Waste Minimization Division EM-352. Using a 12-step benchmarking process, the team examined current waste minimization processes for liquid photographic waste used at their sites and used telephone and written questionnaires to find ``best-in-class`` industrv partners willing to share information about their best waste minimization techniques and technologies through a site visit. Eastman Kodak Co., and Johnson Space Center/National Aeronautics and Space Administration (NASA) agreed to be partners. The site visits yielded strategies for source reduction, recycle/recovery of components, regeneration/reuse of solutions, and treatment of residuals, as well as best management practices. An additional benefit of the work was the opportunity for DOE process experts to network and exchange ideas with their peers at similar sites.

  10. Annual Waste Minimization Summary Report, Calendar Year 2009

    Energy Technology Data Exchange (ETDEWEB)

    NSTec Environmental Restoration

    2010-02-07

    This report summarizes the waste minimization efforts undertaken by National Security Technologies, LLC, for the U. S. Department of Energy, National Nuclear Security Administration Nevada Site Office (NNSA/NSO), during calendar year 2009. This report was developed in accordance with the requirements of the Nevada Test Site Resource Conservation and Recovery Act Permit (No. NEV HW0021), and as clarified in a letter dated April 21, 1995, from Paul Liebendorfer of the Nevada Division of Environmental Protection to Donald Elle of the U.S. Department of Energy, Nevada Operations Office. The NNSA/NSO Pollution Prevention (P2) Program establishes a process to reduce the volume and toxicity of waste generated by NNSA/NSO activities and ensures that proposed methods of treatment, storage, and/or disposal of waste minimize potential threats to human health and the environment. The following information provides an overview of the P2 Program, major P2 accomplishments during the reporting year, a comparison of the current year waste generation to prior years, and a description of efforts undertaken during the year to reduce the volume and toxicity of waste generated by NNSA/NSO.

  11. Best Practice of Construction Waste Management and Minimization

    Directory of Open Access Journals (Sweden)

    Khor Jie Cheng

    2014-07-01

    Full Text Available Material management is an important issue as seen in construction waste management. Best practice of material management is accompanied by various benefits which are acknowledged by several studies. The site layout has particular effects on both materials and their waste through effective waste management practice. Ignoring the benefits of material management could result in a daily reduction in productivity of up to 40% by material wastage. Thus, the benefits of effective material management must be well comprehended for the sake of waste minimization. Another convincing fact about waste is that poor site management accounts for the largest factor of waste generation. Hence the site condition is very crucial in developing effective material management. Factors contributing to the efficiency of material management process are effective logistical management and supply chain management. The logistics system must be performing as schedule so that materials are wisely managed on-site without encountering presence of excessive materials. As materials management is closely related to logistics in construction projects, there will be delay in construction projects when materials are not delivered to site as scheduled. The management must be effective in terms of delivery, off-loading, storage, handling, on-site transportation and on-site utilization of materials.

  12. Waste minimization/pollution prevention study of high-priority waste streams

    Energy Technology Data Exchange (ETDEWEB)

    Ogle, R.B. [comp.

    1994-03-01

    Although waste minimization has been practiced by the Metals and Ceramics (M&C) Division in the past, the effort has not been uniform or formalized. To establish the groundwork for continuous improvement, the Division Director initiated a more formalized waste minimization and pollution prevention program. Formalization of the division`s pollution prevention efforts in fiscal year (FY) 1993 was initiated by a more concerted effort to determine the status of waste generation from division activities. The goal for this effort was to reduce or minimize the wastes identified as having the greatest impact on human health, the environment, and costs. Two broad categories of division wastes were identified as solid/liquid wastes and those relating to energy use (primarily electricity and steam). This report presents information on the nonradioactive solid and liquid wastes generated by division activities. More specifically, the information presented was generated by teams of M&C staff members empowered by the Division Director to study specific waste streams.

  13. Using benchmarking to minimize common DOE waste streams: Volume 5. Office paper waste

    Energy Technology Data Exchange (ETDEWEB)

    Levin, V.

    1995-10-01

    Finding innovative ways to reduce waste streams generated at US Department of Energy (DOE) sites by 50% by the year 2000 is a challenge for DOE`s waste minimization efforts. A team composed of members from several DOE facilities used the quality tool known as benchmarking to improve waste minimization efforts. First the team examined office waste generation and handling processes at their sites. Then team members developed telephone and written questionnaires to help identify potential ``best-in-class`` industry partners willing to share information about their best waste minimization techniques and technologies. The team identified two benchmarking partners, NIKE, Inc., in Beaverton, Oregon, and Microsoft, Inc., in Redmond, Washington. Both companies have proactive, employee-driven environmental issues programs. Both companies report strong employee involvement, management commitment, and readily available markets for recyclable materials such as white paper and nonwhite assorted paper. The availability of markets, the initiative and cooperation of employees, and management support are the main enablers for their programs. At both companies, recycling and waste reduction programs often cut across traditional corporate divisions such as procurement, janitorial services, environmental compliance, grounds maintenance, cafeteria operations, surplus sales, and shipping and receiving. These companies exhibited good cooperation between these functions to design and implement recycling and waste reduction programs.

  14. Pollution prevention and waste minimization in metal finishing

    Energy Technology Data Exchange (ETDEWEB)

    Stimetz, C.J.

    1994-12-01

    This study was done to identify pollution prevention and waste minimization opportunities in the general plating department and the printed circuit board processing department. Recommendations for certain recycle and recovery technologies were mad in order to reduce usage of acids and the volume of heavy metal sludge that is formed at the industrial Wastewater Pretreatment Facility (IWPF). Some of these technologies discussed were acid purification, electrowinning, and ion exchange. Specific technologies are prescribed for specific processes. Those plating processes where the metals can be recovered are copper, nickel, gold, cadmium, tin, lead, and rhodium.

  15. Hanford Site waste minimization and pollution prevention awareness program plan

    Energy Technology Data Exchange (ETDEWEB)

    Place, B.G.

    1998-09-24

    This plan, which is required by US Department of Energy (DOE) Order 5400. 1, provides waste minimization and pollution prevention guidance for all Hanford Site contractors. The plan is primary in a hierarchical series that includes the Hanford Site Waste Minimization and Pollution Prevention Awareness Program Plan, Prime contractor implementation plans, and the Hanford Site Guide for Preparing and Maintaining Generator Group Pollution Prevention Program Documentation (DOE-RL, 1997a) describing programs required by Resource Conservation and Recovery Act of 1976 (RCRA) 3002(b) and 3005(h) (RCRA and EPA, 1994). Items discussed include the pollution prevention policy and regulatory background, organizational structure, the major objectives and goals of Hanford Site`s pollution prevention program, and an itemized description of the Hanford Site pollution prevention program. The document also includes US Department of Energy, Richland Operations Office`s (RL`s) statement of policy on pollution prevention as well as a listing of regulatory drivers that require a pollution prevention program.

  16. RCRA Permit for a Hazardous Waste Management Facility, Permit Number NEV HW0101, Annual Summary/Waste Minimization Report

    Energy Technology Data Exchange (ETDEWEB)

    Arnold, Patrick [NSTec

    2014-02-14

    This report summarizes the EPA identification number of each generator from which the Permittee received a waste stream, a description and quantity of each waste stream in tons and cubic feet received at the facility, the method of treatment, storage, and/or disposal for each waste stream, a description of the waste minimization efforts undertaken, a description of the changes in volume and toxicity of waste actually received, any unusual occurrences, and the results of tank integrity assessments. This Annual Summary/Waste Minimization Report is prepared in accordance with Section 2.13.3 of Permit Number NEV HW0101.

  17. Proceedings of pollution prevention and waste minimization tools workshop

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-11-01

    Pollution Prevention (P2) has evolved into one of DOE`s sprime strategies to meet environmental, fiscal, and worker safety obligations. P2 program planning, opportunity identification, and implementation tools were developed under the direction of the Waste Minimization Division (EM-334). Forty experts from EM, DP, ER and DOE subcontractors attended this 2-day workshop to formulate the incentives to drive utilization of these tools. Plenary and small working group sessions were held both days. Working Group 1 identified incentives to overcoming barriers in the area of P2 program planning and resource allocation. Working Group 2 identified mechanisms to drive the completion of P2 assessments and generation of opportunities. Working Group 3 compiled and documented a broad range of potential P2 incentives that address fundamental barriers to implementation of cost effective opportunities.

  18. INTELLIGENT DECISION SUPPORT FOR WASTE MINIMIZATION IN ELECTROPLATING PLANTS. (R824732)

    Science.gov (United States)

    AbstractWastewater, spent solvent, spent process solutions, and sludge are the major waste streams generated in large volumes daily in electroplating plants. These waste streams can be significantly minimized through process modification and operational improvement. I...

  19. Evaluation of Practicing sustainable Industrial Solid Waste Minimization by Manufacturing Firms in Malaysia: Strengths and Weaknesses.

    Science.gov (United States)

    Mallak, Shadi Kafi; Bakri Ishak, Mohd; Mohamed, Ahmad Fariz

    2016-09-13

    Malaysia is facing an increasing trend in industrial solid waste generation due to industrial development.Thus there is a paramount need in taking a serious action to move toward sustainable industrial waste management. The main aim of this study is to assess practicing solid waste minimization by manufacturing firms in Shah Alam industrial state, Malaysia. This paper presents a series of descriptive and inferential statistical analysis regarding the level and effects of practicing waste minimization methods, and seriousness of barriers preventing industries from practicing waste minimization methods. For this purpose the survey questions were designed such that both quantitative (questionnaire) and qualitative (semi-structures interview) data were collected concurrently. Analysis showed that, the majority of firms (92%) dispose their wastes rather than practice other sustainable waste management options. Also waste minimization methods such as segregation of wastes, on-site recycle and reuse, improve housekeeping and equipment modification were found to have significant contribution in waste reduction (pstrengths, weaknesses, threats and opportunities. Accordingly, ten policies were recommended for improvement of practicing waste minimization by manufacturing firms as the main aim of this research. Implications This manuscript critically analysis waste minimization practices by manufacturing firms in Malaysia. Both qualitative and quantitative data collection and analysis were conducted to formulate SWOT and TOWS matrix in order to recommend policies and strategies for improvement of solid waste minimization by manufacturing industries. The results contribute to the knowledge and the findings of this study provide a useful baseline information and data on industrial solid waste generation and waste minimization practice.

  20. From waste minimization to ISO 14000: Taiwan`s experience and prospects

    Energy Technology Data Exchange (ETDEWEB)

    Wen-Huei Chen; Wain-Sun Hou [China Technical Consultants, Inc., Taipei (Taiwan, Province of China)

    1996-12-31

    Taiwan has completed a very successful five-year industrial waste minimization (IWM) demonstration and promotion project sponsored by the government. From 1990 to 1995, the project successfully disseminated the IWM concept of pollution prevention (P2) to industries. It effectively reduced industrial waste while significantly benefitting the economy by assisting industries in implementing in-plant IWM programs. In July 1995, the second stage of the five-year IWM and ISO 14000 promotion project was initiated for further promoting the IWM, P2, and cleaner production and, in particular, coping with the upcoming international environmental management standards (ISO 14000). To assist industries in establishing an environmental management system (EMS) and accumulating related experience, an EMS pilot demonstration project of five model industries and an ISO 14001 EMS demonstration and promotion project for 22 factories in 13 industries were initiated in October 1995 and August 1996, respectively. These projects can assist Taiwan`s industries in changing the constitution of their enterprises, enhancing competition in the international market, and helping our nation achieve the forerunner`s profits in sustainable development. 9 refs., 3 figs.

  1. Using information management systems to support waste minimization at US Army installations

    Energy Technology Data Exchange (ETDEWEB)

    Myers, R.S.; Butner, R.S.; Callaway, J.W.; Levine, L.O.

    1990-04-01

    The Army's to reduce hazardous waste generation emphasize reduction at the source. Waste minimization and environmental regulatory compliance are also being integrated into strategies and activities aimed at modernization of industrial operations. The Assistant Secretary of the Army for Research, Development and Acquisition (ASARDA) is conducting a Hazardous Waste Intervention study to understand and evaluate the existing operations and to assess waste minimization opportunities. The overall ASARDA study consists of several teams working on various aspects of hazardous waste intervention at Army installations. The first team is investigating methods of minimizing hazardous waste by modifying the acquisition cycle. This effort is aimed at reducing the generation of hazardous waste by reducing the number and the quantities of hazardous materials that are specified in program and product development. A second team is investigating the technological aspects of waste minimization. Finally, a third team is investigating opportunities for waste minimization by better managing the life-cycle of hazardous materials and hazardous waste. The third team is involved in several tasks, including evaluating the feasibility of using Information Management Systems (IMS) to support waste minimization. This paper summarizes the primary conclusions and recommendations from the information management system evaluation portion of PNL's work.

  2. ENVIRONMENTAL RESEARCH BRIEF: WASTE MINIMIZATION ASSESSMENT FOR A MANUFACTURER OF ALUMINUM CANS

    Science.gov (United States)

    The U.S. Environmental Protection Agency (EPA) has funded a pilot project to assist small- and medium- size manufacturers who want to minimize their generation of hazardous waste but lack the expertise to do so. Waste Minimization Assessment Centers (WMACs) were established at se...

  3. WASTE MINIMIZATION ASSESSMENT FOR A MANUFACTURER OF CUSTOM MOLDED PLASTIC PRODUCTS

    Science.gov (United States)

    The U.S. Environmental Protection Agency (EPA) has funded a pilot project to assist small- and medium-size manufacturers who want to minimize their generation of waste but who lack the expertise to do so. Waste Minimization Assessment Centers (WMACs) were established at selected ...

  4. ENVIRONMENTAL RESEARCH BRIEF: WASTE MINIMIZATION ASSESSMENT FOR A MANUFACTURER OF PRINTED PLASTIC BAGS

    Science.gov (United States)

    The U.S. Environmental Protection Agency (EPA) has funded a pilot project to assist small- and medium-size manufacturers who want to minimize their generation of hazardous waste but who lack the expertise to do so. Waste Minimization Assessment Centers (WMACs) were established ...

  5. ENVIRONMENTAL RESEARCH BRIEF: WASTE MINIMIZATION ASSESSMENT FOR A BUMPER REFINISHING PLANT

    Science.gov (United States)

    The U.S. Environmental Protection Agency (EPA) has funded a pilot project to assist small- and medium-size manufacturers who want to minimize their generation of hazardous waste but lack the expertise to do so. Waste Minimization Assessment Centers (WMACs) were established at se...

  6. Wood waste minimization in the timber sector of Ghana: a systems approach to reduce environmental impact.

    NARCIS (Netherlands)

    Eshun, J.F.; Potting, J.; Leemans, R.

    2012-01-01

    This paper explores the potential of minimizing wood waste to reduce the environmental impact in the timber sector i.e. forestry and timber industry subsystem of Ghana. This study is a follow up of 3 earlier studies on the timber sector. These studies consistently identified minimizing wood waste as

  7. WASTE MINIMIZATION ASSESSMENT FOR A MANUFACTURER OF CORN SYRUP AND CORN STARCH

    Science.gov (United States)

    The U.S.Environmental Protection Agency (EPA) has funded a pilot project to assist small and medium-size manufacturers who want to minimize their geneation of waste but who lack the expertise to do so. In an effort to assist these manufacturers, Waste Minimization Assessment Cent...

  8. Information processing to determine waste minimization/pollution prevention strategies in the petroleum industry

    Energy Technology Data Exchange (ETDEWEB)

    Falcon, Mariali F. de [CORPOVEN, S.A. (Venezuela)

    1993-12-31

    With the passage of the 1984 Hazardous and Solid Waste Amendments to the Resource Conservation and Recovery Act in the United States, industries, and particularly the petroleum industry, have become more interested in their waste management practices. This works aims to present a methodology to organize the collected data concerning waste minimization and, or, pollution prevention in the petroleum industry into a bibliographic database

  9. Potentials for food waste minimization and effects on potential biogas production through anaerobic digestion.

    Science.gov (United States)

    Schott, Anna Bernstad Saraiva; Vukicevic, Sanita; Bohn, Irene; Andersson, Tova

    2013-08-01

    Several treatment alternatives for food waste can result in both energy and nutrient recovery, and thereby potential environmental benefits. However, according to the European Union waste management hierarchy, waste prevention should be the prioritized strategy to decrease the environmental burdens from all solid waste management. The aim of the present study was therefore to investigate the potential for food waste minimization among Swedish households through an investigation of the amount of avoidable food waste currently disposed of. A further aim was to investigate the effect on the national biogas production potential through anaerobic digestion of food waste, considering minimization potentials. A method for waste composition analyses of household food waste, where a differentiation between avoidable and unavoidable food waste is made, was used in a total of 24 waste composition analyses of household waste from Swedish residential areas. The total household food waste generation reached 3.4 kg (household and week)(-1), on average, of which 34% is avoidable. The theoretical methane (CH4) potential in unavoidable food waste reached 442 Ndm(3) (kg VS)(-1) or 128 Nm(3) tonne(-1) wet waste, while the measured (mesophilic CH4 batch tests) CH4 production reached 399 Ndm(3) (kg VS)(-1), which is lower than several previous assessments of CH4 production from household food waste. According to this study the combination of a decrease in food waste generation-in case of successful minimization-and decreased CH4 production from unavoidable food waste will thus result in lower total potential energy recovery from household food waste through anaerobic digestion CH4 potential than previously stated.

  10. Zone Freezing Study for Pyrochemical Process Waste Minimization

    Energy Technology Data Exchange (ETDEWEB)

    Ammon Williams

    2012-05-01

    Pyroprocessing technology is a non-aqueous separation process for treatment of used nuclear fuel. At the heart of pyroprocessing lies the electrorefiner, which electrochemically dissolves uranium from the used fuel at the anode and deposits it onto a cathode. During this operation, sodium, transuranics, and fission product chlorides accumulate in the electrolyte salt (LiCl-KCl). These contaminates change the characteristics of the salt overtime and as a result, large volumes of contaminated salt are being removed, reprocessed and stored as radioactive waste. To reduce the storage volumes and improve recycling process for cost minimization, a salt purification method called zone freezing has been proposed at Korea Atomic Energy Research Institute (KAERI). Zone freezing is melt crystallization process similar to the vertical Bridgeman method. In this process, the eutectic salt is slowly cooled axially from top to bottom. As solidification occurs, the fission products are rejected from the solid interface and forced into the liquid phase. The resulting product is a grown crystal with the bulk of the fission products near the bottom of the salt ingot, where they can be easily be sectioned and removed. Despite successful feasibility report from KAERI on this process, there were many unexplored parameters to help understanding and improving its operational routines. Thus, this becomes the main motivation of this proposed study. The majority of this work has been focused on the CsCl-LiCl-KCl ternary salt. CeCl3-LiCl-KCl was also investigated to check whether or not this process is feasible for the trivalent species—surrogate for rare-earths and transuranics. For the main part of the work, several parameters were varied, they are: (1) the retort advancement rate—1.8, 3.2, and 5.0 mm/hr, (2) the crucible lid configurations—lid versus no-lid, (3) the amount or size of mixture—50 and 400 g, (4) the composition of CsCl in the salt—1, 3, and 5 wt%, and (5) the

  11. An Exploration of Healthcare Inventory and Lean Management in Minimizing Medical Supply Waste in Healthcare Organizations

    Science.gov (United States)

    Hicks, Rodney

    2013-01-01

    The purpose of this study was to understand how lean thinking and inventory management technology minimize expired medical supply waste in healthcare organizations. This study was guided by Toyota's theory of lean and Mintzberg's theory of management development to explain why the problem of medical supply waste exists. Government…

  12. Evaluation of hazardous waste minimization techniques for fuel tanker purging at Fort Story, Virginia

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1989-06-01

    The purpose of the project is to develop and evaluate techniques for purging fuel tankers that minimize the volume of wastes generated and to evaluate techniques to recycle, treat, and dispose of purging wastes. The approach taken in this project was to visit Fort Story and interview company personnel to define purging requirements and company constraints. Other military installations, federal agencies, and private industries were then contacted to identify potentially relevant techniques used at their locations. Hazardous Waste Minimization (HAZMIN) techniques were combined with alternatives for minimizing the frequency of purging, offsite purging, onsite purging, and waste treatment. Alternatives were then evaluated on the basis of their applicability to operations at Fort Story, their technical effectiveness, their cost, and safety considerations.

  13. Critical management practices influencing on-site waste minimization in construction projects.

    Science.gov (United States)

    Ajayi, Saheed O; Oyedele, Lukumon O; Bilal, Muhammad; Akinade, Olugbenga O; Alaka, Hafiz A; Owolabi, Hakeem A

    2017-01-01

    As a result of increasing recognition of effective site management as the strategic approach for achieving the required performance in construction projects, this study seeks to identify the key site management practices that are requisite for construction waste minimization. A mixed methods approach, involving field study and survey research were used as means of data collection. After confirmation of construct validity and reliability of scale, data analysis was carried out through a combination of Kruskal-Wallis test, descriptive statistics and exploratory factor analysis. The study suggests that site management functions could significantly reduce waste generation through strict adherence to project drawings, and by ensuring fewer or no design changes during construction process. Provision of waste skips for specific materials and maximisation of on-site reuse of materials are also found to be among the key factors for engendering waste minimization. The result of factor analysis suggests four factors underlying on-site waste management practices with 96.093% of total variance. These measures include contractual provisions for waste minimization, waste segregation, maximisation of materials reuse and effective logistic management. Strategies through which each of the underlying measures could be achieved are further discussed in the paper. Findings of this study would assist construction site managers and other site operatives in reducing waste generated by construction activities. Copyright © 2016 Elsevier Ltd. All rights reserved.

  14. IDENTIFICATION AND CLASSIFICATION OF INDUSTRIAL SOLID WASTES IN AMMONIA UNIT OF RAZI PETROCHEMICAL COMPLEX AND FEASIBILITY OF WASTE MINIMIZATION

    Directory of Open Access Journals (Sweden)

    F. Fakheri Raouf, R. Nabizadeh and N. Jafarzadeh

    2005-10-01

    Full Text Available Petrochemical industries are considered as strategic and important sectors in economic development of Iran. Razi petrochemical factory is one of complex in Iran, established in 1970 with 100 hectare. In this research, the possibility of waste minimization in the ammonia unit of Razi petrochemical complex with about 1000 tons per year was studied for a period of 18 months from September 2003 to April 2005. More than 20 site visits were conducted and the required information was collected. Factors such as industrial solid wastes quality and quantity, sources of generation, production period and the present management practice, were studied. Petrochemical solid wastes were classified based on the recommended method of the United Nations and appropriate policies were suggested for waste minimization. The collected results of this study show production of 185 tons of industrial solid wastes from 45 sources which contained 68.5% catalysts, 10.25% metal barrels, 18.61% aluminum ball, 2.62% plastic barrels and 0.02% paper. 93.3% of these wastes were generated as the result of catalysts change, 3.3% as the result of using chemicals and oils, 1.7% as the result of methanol solution amid application, and 1.1% because of aluminum ball changes. Based on the UNEP methods, the ammonia unit wastes classified as 19/7%hazadrous and 87,12% non hazardous. At present 87.12% of these wastes are being dumped in the area and 12.88% are sold. Proposed procedures for waste minimization contain 68.5% reuse and recycling and 31.5% recycling.

  15. INNOVATIVE PRACTICES FOR TREATING WASTE STREAMS CONTAINING HEAVY METALS: A WASTE MINIMIZATION APPROACH

    Science.gov (United States)

    Innovative practices for treating waste streams containing heavy metals often involve technologies or systems that either reduce the amount of waste generated or recover reusable resources. With the land disposal of metal treatment residuals becoming less of an accepted waste man...

  16. A Review of Effectiveness of Construction Waste Minimization Practices in Bauchi State, Nigeria

    Directory of Open Access Journals (Sweden)

    Babangida Baba

    2017-11-01

    Full Text Available This paper reviewed the existing literature on effectiveness of construction waste minimization in Nigeria with particular interest in Bauchi State. The study highlighted the menace of construction waste to the environment. The Nigerian construction industry comprises foreign and indigenous firms which are classified into small, medium and large according to their level of capitalization and annual turnover. In the real industrialized countries, the construction industry can be responsible for up to 20 % of the GDP and employs up to 12 % of the total labour force. In Nigeria, the sector contributes 3.2 % of GDP. This is a clear indication that construction industry in Nigeria failed to meet expectations of governments, clients and society. The material and method of this research study utilized a secondary source of data. A critical review of this recent journal articles posited new findings of effectiveness of construction waste minimization. To ascertain the actual happenings in the construction industries within and beyond the study area. The findings of this research study indicated that environmental pollution is caused by construction waste in the study area. It is also revealed that indigenous firms generate large volume of construction waste. It was evident that construction waste is ineffective to the health condition of the environment. The conclusion is drawn from the study also revealed that different approach and method should be applied to curtail and minimize construction waste effectiveness in the study area.

  17. An analysis of radioactive waste minimization efforts at Los Alamos National Laboratory

    Energy Technology Data Exchange (ETDEWEB)

    Voit, S.L.; Boerigter, S.T.

    1997-09-30

    LANL will be the primary DOE facility for plutonium research and development and plutonium processing. A summary of the currently generated waste types, volumes, generating facilities or programs, and disposal costs are given in this report along with future waste generation projections. Several key existing technologies have been identified that could be introduced to reduce the generated waste at LANL. Four of these are discussed in detail in this report: (1) electrolytic surface decontamination, (2) electrochemical treatment of mixed wastes, (3) Long Range Alpha Detection (LRAD), and (4) Segmented Gate and Containerized Vat Leach System (SGS/CVL). These technologies may be implemented as modifications in upstream processes as well as more efficient volume reduction and segregation. The four technologies are mature enough to be implemented in the next two to three years and can be done so with the support for capital and operational costs. Also discussed in this report is a small sample of some of the recent waste minimization success stories that have been implemented. Several technologies are presented that are either currently being investigated or on hold due to lack of funding at LANL but show potential for making significant gains in waste minimization. This report is intended to provide a review of the waste minimization issues and analysis of the impact of implementing a few of these technologies.

  18. Minimally processed beetroot waste as an alternative source to obtain functional ingredients.

    Science.gov (United States)

    Costa, Anne Porto Dalla; Hermes, Vanessa Stahl; Rios, Alessandro de Oliveira; Flôres, Simone Hickmann

    2017-06-01

    Large amounts of waste are generated by the minimally processed vegetables industry, such as those from beetroot processing. The aim of this study was to determine the best method to obtain flour from minimally processed beetroot waste dried at different temperatures, besides producing a colorant from such waste and assessing its stability along 45 days. Beetroot waste dried at 70 °C originates flour with significant antioxidant activity and higher betalain content than flour produced from waste dried at 60 and 80 °C, while chlorination had no impact on the process since microbiological results were consistent for its application. The colorant obtained from beetroot waste showed color stability for 20 days and potential antioxidant activity over the analysis period, thus it can be used as a functional additive to improve nutritional characteristics and appearance of food products. These results are promising since minimally processed beetroot waste can be used as an alternative source of natural and functional ingredients with high antioxidant activity and betalain content.

  19. Waste minimization study for a printed circuit board manufacturing facility in Taiwan

    Energy Technology Data Exchange (ETDEWEB)

    Chiu, Shen-yann; Huang, Hann S.; Peters, R.W.; Tsai, S.Y. (Argonne National Lab., IL (USA)); Tsai, Wen-Tien; Shieh, Shih-Shien; Hsieh, Te-Yuan; Hwang, Li-Shyong (CTCI Corp., Taipei (Taiwan)); Liu, Solo; Peng, Chien-Tang (Printed Wire Corp., Ping Chen, Taoyuan (Taiwan)); Wu, Min H. (Waste Minimization Technology International, Inc., Pewaukee, WI (USA))

    1990-01-01

    This paper presents a demonstration of industrial waste minimization sponsored by the Environmental Protection Administration, Taiwan, Republic of China. Waste reduction opportunities are identified and evaluated for a printed circuit board manufacturing facility in Taiwan. Plant audits were conducted on various processes, such as deburring, alkaline etching, black oxidation, desmearing, electroless copper, and copper and tin/lead plating. Specific areas in which the wastes could be minimized, such as reducing the amount of dragout and rinse water requirements in the plating and etchant lines, and on-site treatment and reuse of spent bath solutions were identified, assessed, and implemented. Jar tests on the wastewater were performed, and the results were used to improve the efficiency of the wastewater treatment plant for removal of heavy metals and reduction of sludge generation. In addition, administrative controls of hazardous wastes designed to reduce associated health and environmental hazards were recommended. 4 figs., 9 tabs.

  20. Uranium Mill Tailings remedial action project waste minimization and pollution prevention awareness program plan

    Energy Technology Data Exchange (ETDEWEB)

    1994-07-01

    The purpose of this plan is to establish a waste minimization and pollution prevention awareness (WM/PPA) program for the U.S. Department of Energy`s (DOE) Uranium Mill Tailings Remedial Action (UMTRA) Project. The program satisfies DOE requirements mandated by DOE Order 5400.1. This plan establishes planning objectives and strategies for conserving resources and reducing the quantity and toxicity of wastes and other environmental releases.

  1. Minimalism

    CERN Document Server

    Obendorf, Hartmut

    2009-01-01

    The notion of Minimalism is proposed as a theoretical tool supporting a more differentiated understanding of reduction and thus forms a standpoint that allows definition of aspects of simplicity. This book traces the development of minimalism, defines the four types of minimalism in interaction design, and looks at how to apply it.

  2. Chelation technology: a promising green approach for resource management and waste minimization.

    Science.gov (United States)

    Chauhan, Garima; Pant, K K; Nigam, K D P

    2015-01-01

    Green chemical engineering recognises the concept of developing innovative environmentally benign technologies to protect human health and ecosystems. In order to explore this concept for minimizing industrial waste and for reducing the environmental impact of hazardous chemicals, new greener approaches need to be adopted for the extraction of heavy metals from industrial waste. In this review, a range of conventional processes and new green approaches employed for metal extraction are discussed in brief. Chelation technology, a modern research trend, has shown its potential to develop sustainable technology for metal extraction from various metal-contaminated sites. However, the interaction mechanism of ligands with metals and the ecotoxicological risk associated with the increased bioavailability of heavy metals due to the formation of metal-chelant complexes is still not sufficiently explicated in the literature. Therefore, a need was felt to provide a comprehensive state-of-the-art review of all aspects associated with chelation technology to promote this process as a green chemical engineering approach. This article elucidates the mechanism and thermodynamics associated with metal-ligand complexation in order to have a better understanding of the metal extraction process. The effects of various process parameters on the formation and stability of complexes have been elaborately discussed with respect to optimizing the chelation efficiency. The non-biodegradable attribute of ligands is another important aspect which is currently of concern. Therefore, biotechnological approaches and computational tools have been assessed in this review to illustrate the possibility of ligand degradation, which will help the readers to look for new environmentally safe mobilizing agents. In addition, emerging trends and opportunities in the field of chelation technology have been summarized and the diverse applicability of chelation technology in metal extraction from

  3. Trash-to-Gas: Using Waste Products to Minimize Logistical Mass During Long Duration Space Missions

    Science.gov (United States)

    Hintze, Paul. E.; Caraccio, Anne J.; Anthony, Stephen M.; Tsoras, Alexandra N.; Nur, Monoita; Devor, Robert; Captain, James G.

    2013-01-01

    Just as waste-to-energy processes utilizing municipal landftll and biomass wastes are finding increased terrestrial uses, the Trash-to-Gas (TtG) project seeks to convert waste generated during spaceflight into high value commodities. These include methane for propulsion and water for life support in addition to a variety of other gasses. TtG is part of the Logistic Reduction and Repurposing (LRR) project under the NASA Advanced Exploration Systems Program. The LRR project will enable a largely mission-independent approach to minimize logistics contributions to total mission architecture mass. LRR includes technologies that reduce the amount of consumables that need to be sent to space, repurpose items sent to space, or convert wastes to commodities. Currently, waste generated on the International Space Station is stored inside a logistic module which is de-orbited into Earth's atmosphere for destruction. The waste consists of food packaging, food, clothing and other items. This paper will discuss current results on incineration as a waste processing method. Incineration is part of a two step process to produce methane from waste: first the waste is converted to carbon oxides; second, the carbon oxides are fed to a Sabatier reactor where they are converted to methane. The quantities of carbon dioxide, carbon monoxide, methane and water were measured under the different thermal degradation conditions. The overall carbon conversion efficiency and water recovery are discussed.

  4. RCRA Permit for a Hazardous Waste Management Facility Permit Number NEV HW0101 Annual Summary/Waste Minimization Report - Calendar Year 2014

    Energy Technology Data Exchange (ETDEWEB)

    Arnold, Patrick [National Security Technologies, LLC, Mercury, NV (United States)

    2015-02-17

    This report summarizes the EPA identification number of each generator from which the Permittee received a waste stream, a description and quantity of each waste stream in tons and cubic feet received at the facility, the method of treatment, storage, and/or disposal for each waste stream, a description of the waste minimization efforts undertaken, a description of the changes in volume and toxicity of waste actually received, any unusual occurrences, and the results of tank integrity assessments. This Annual Summary/Waste Minimization Report is prepared in accordance with Section 2.13.3 of Permit Number NEV HW0101.

  5. RCRA Permit for a Hazardous Waste Management Facility Permit Number NEV HW0101 Annual Summary/Waste Minimization Report Calendar Year 2012, Nevada National Security Site, Nevada

    Energy Technology Data Exchange (ETDEWEB)

    Arnold, P. M.

    2013-02-21

    This report summarizes the U.S. Environmental Protection Agency (EPA) identification number of each generator from which the Permittee received a waste stream, a description and quantity of each waste stream in tons and cubic feet received at the facility, the method of treatment, storage, and/or disposal for each waste stream, a description of the waste minimization efforts undertaken, a description of the changes in volume and toxicity of waste actually received, any unusual occurrences, and the results of tank integrity assessments. This Annual Summary/Waste Minimization Report is prepared in accordance with Section 2.13.3 of Permit Number NEV HW0101, issued 10/17/10.

  6. RCRA Permit for a Hazardous Waste Management Facility Permit Number NEV HW0101 Annual Summary/Waste Minimization Report Calendar Year 2011

    Energy Technology Data Exchange (ETDEWEB)

    NSTec Environmental Restoration

    2012-02-16

    This report summarizes the U.S. Environmental Protection Agency (EPA) identification number of each generator from which the Permittee received a waste stream; a description and quantity of each waste stream in tons and cubic feet received at the facility; the method of treatment, storage, and/or disposal for each waste stream; a description of the waste minimization efforts undertaken; a description of the changes in volume and toxicity of waste actually received; any unusual occurrences; and the results of tank integrity assessments. This Annual Summary/Waste Minimization Report is prepared in accordance with Section 2.13.3 of Permit Number NEV HW0101.

  7. Utilizing environmental management information systems to monitor chemical usage and facilitate waste minimization

    Energy Technology Data Exchange (ETDEWEB)

    Blazer, T.L.; Kinney, R.W. [Modern Technologies Corporation, Dayton, OH (United States)

    1996-10-01

    Waste minimization and pollution prevention activities have proven to be valuable to the chemical industry`s and the chemical user`s bottom line. Many companies have found that, with a modest initial capital investment and product modifications, mounds of bureaucratic liability can be removed and substantial cost savings can be realized.

  8. WESF hot cells waste minimization criteria hot cells window seals evaluation

    Energy Technology Data Exchange (ETDEWEB)

    Walterskirchen, K.M.

    1997-03-31

    WESF will decouple from B Plant in the near future. WESF is attempting to minimize the contaminated solid waste in their hot cells and utilize B Plant to receive the waste before decoupling. WESF wishes to determine the minimum amount of contaminated waste that must be removed in order to allow minimum maintenance of the hot cells when they are placed in ''laid-up'' configuration. The remaining waste should not cause unacceptable window seal deterioration for the remaining life of the hot cells. This report investigates and analyzes the seal conditions and hot cell history and concludes that WESF should remove existing point sources, replace cerium window seals in F-Cell and refurbish all leaded windows (except for A-Cell). Work should be accomplished as soon as possible and at least within the next three years.

  9. Unrestricted disposal of minimal activity levels of radioactive wastes: exposure and risk calculations

    Energy Technology Data Exchange (ETDEWEB)

    Fields, D.E.; Emerson, C.J.

    1984-08-01

    The US Nuclear Regulatory Commission is currently considering revision of rule 10 CFR Part 20, which covers disposal of solid wastes containing minimal radioactivity. In support of these revised rules, we have evaluated the consequences of disposing of four waste streams at four types of disposal areas located in three different geographic regions. Consequences are expressed in terms of human exposures and associated health effects. Each geographic region has its own climate and geology. Example waste streams, waste disposal methods, and geographic regions chosen for this study are clearly specified. Monetary consequences of minimal activity waste disposal are briefly discussed. The PRESTO methodology was used to evaluate radionuclide transport and health effects. This methodology was developed to assess radiological impacts to a static local population for a 1000-year period following disposal. Pathways and processes of transit from the trench to exposed populations included the following considerations: groundwater transport, overland flow, erosion, surface water dilution, resuspension, atmospheric transport, deposition, inhalation, and ingestion of contaminated beef, milk, crops, and water. 12 references, 2 figures, 8 tables.

  10. Waste Minimization Protocols for the Process of Synthesizing Zeolites from South African Coal Fly Ash

    OpenAIRE

    Petrik, Leslie F.; Tunde V. Ojumu; Du Plessis, Pieter W.

    2013-01-01

    Production of a high value zeolite from fly ash has been shown to be an avenue for the utilization of South African fly ash which presently constitutes a huge disposal problem. The synthesis of zeolites Na-P1 and analcime on a micro-scale has been successful and preliminary investigation shows that scale-up synthesis is promising. However, the post-synthesis supernatant waste generated contains high levels of NaOH that may constitute a secondary disposal problem. A waste minimization protocol...

  11. Annual Waste Minimization Summary Report, Calendar Year 2010, U.S. Environmental Protection Agency Identification No. NV3890090001

    Energy Technology Data Exchange (ETDEWEB)

    Haworth, D.M.

    2011-01-30

    This report summarizes the waste minimization efforts undertaken by National Security TechnoIogies, LLC, for the U. S. Department of Energy, National Nuclear Security Administration Nevada Site Office (NNSA/NSO), during calendar year 2010. The NNSA/NSO Pollution Prevention Program establishes a process to reduce the volume and toxicity of waste generated by NNSA/NSO activities and ensures that proposed methods of treatment, storage, and/or disposal of waste minimize potential threats to human health and the environment.

  12. Discard mitigation – what we can learn from waste minimization practices in other natural resources?

    OpenAIRE

    Stockhausen, Björn; OFFICER R.a.; SCOTT ROBERT

    2011-01-01

    Solutions to the problem of discarding in fisheries have been debated for decades. Despite this attention, measures to ameliorate discarding have had limited success. Regulators, researchers, and industry continue to struggle with fisheries management and foregone yield in the face of the continued wastage of valuable resources due to discarding. Waste minimization and by-product utilization are powerful imperatives in other sectors that are also reliant on the harvest of natural resources...

  13. Waste Minimization Protocols for the Process of Synthesizing Zeolites from South African Coal Fly Ash

    Directory of Open Access Journals (Sweden)

    Leslie F. Petrik

    2013-04-01

    Full Text Available Production of a high value zeolite from fly ash has been shown to be an avenue for the utilization of South African fly ash which presently constitutes a huge disposal problem. The synthesis of zeolites Na-P1 and analcime on a micro-scale has been successful and preliminary investigation shows that scale-up synthesis is promising. However, the post-synthesis supernatant waste generated contains high levels of NaOH that may constitute a secondary disposal problem. A waste minimization protocol was developed to reduce the volume of waste generated with a view to enhancing the feasibility of the scale synthesis. Series of experiments were conducted in 100 mL jacketed batch reactors. Fly ash was reacted with 5 Mol NaOH on a 1:1 mass basis during the aging step, followed by hydrothermal treatment in which ultrapure water was added to the slurry. This study shows that by re-introducing the supernatant waste into the experiments in such a way that it supplies the required reagent (NaOH for the zeolite synthesis, zeolite Na-P1 and analcime can be synthesized. It also shows that the synthesis process can be altered to allow up to 100% re-use of the supernatant waste to yield high value zeolitic products. This study effectively constructed two protocols for the minimization of waste generated during the synthesis of zeolites from South African coal fly ash. This result could be used to establish a basis for legal and environmental aspects involved in the commission of a full-scale plant synthesizing zeolites NaP1 and analcime.

  14. Waste Minimization Protocols for the Process of Synthesizing Zeolites from South African Coal Fly Ash.

    Science.gov (United States)

    Plessis, Pieter W Du; Ojumu, Tunde V; Petrik, Leslie F

    2013-04-29

    Production of a high value zeolite from fly ash has been shown to be an avenue for the utilization of South African fly ash which presently constitutes a huge disposal problem. The synthesis of zeolites Na-P1 and analcime on a micro-scale has been successful and preliminary investigation shows that scale-up synthesis is promising. However, the post-synthesis supernatant waste generated contains high levels of NaOH that may constitute a secondary disposal problem. A waste minimization protocol was developed to reduce the volume of waste generated with a view to enhancing the feasibility of the scale synthesis. Series of experiments were conducted in 100 mL jacketed batch reactors. Fly ash was reacted with 5 Mol NaOH on a 1:1 mass basis during the aging step, followed by hydrothermal treatment in which ultrapure water was added to the slurry. This study shows that by re-introducing the supernatant waste into the experiments in such a way that it supplies the required reagent (NaOH) for the zeolite synthesis, zeolite Na-P1 and analcime can be synthesized. It also shows that the synthesis process can be altered to allow up to 100% re-use of the supernatant waste to yield high value zeolitic products. This study effectively constructed two protocols for the minimization of waste generated during the synthesis of zeolites from South African coal fly ash. This result could be used to establish a basis for legal and environmental aspects involved in the commission of a full-scale plant synthesizing zeolites NaP1 and analcime.

  15. 1994 annual report on waste generation and waste minimization progress as required by DOE Order 5400.1

    Energy Technology Data Exchange (ETDEWEB)

    Irwin, E.F.; Poligone, S.E.

    1995-10-16

    The Y-12 Plant serves as a key manufacturing technology center for the development and demonstration of unique materials, components, and services of importance to the Department of Energy (DOE) and the nation. This is accomplished through the reclamation and storage of nuclear materials, manufacture of nuclear materials, manufacture of components for the nation`s defense capabilities, support to national security programs, and services provided to other customers as approved by DOE. We are recognized by our people, the community, and our customers as innovative, responsive, and responsible. We are a leader in worker health and safety, environmental protection, and stewardship of our national resources. As a DOE facility, Y-12 also supports DOE`s waste minimization mission. Data contained in this report represents waste generation in Tennessee.

  16. A Review on Waste Minimization by Adopting in Self Compacting Concrete

    Directory of Open Access Journals (Sweden)

    Shahidan S.

    2016-01-01

    Full Text Available Self-compacting concrete (SCC was first developed in late 80’s in Japan. SCC is well known for its self-consolidation and able to occupy spaces in the formwork without vibration and become new interesting topic in Construction and Building Materials Research. The aim of this review is to summaries the previous research work related to utilization of waste minimization in SCC from 2009 to 2015 through available literature. It is important to expose new researchers on concept and fundamental theory developed by previous researchers as a reference and guidance in their research. There were a lot of opportunity to be explored in developing SCC especially in utilizing waste material as replacement materials or additives used and mix design method for rheological improvement in SCC. However, these review only focusing on waste materials that have significant to be taken care to reduce environmental impact such as waste product from construction industry and by product industry. As conclusion, this paper will provide significant idea and useful information to those new to SCC and fellow researchers for future studies in utilizing waste materials in SCC mix design.

  17. Reuse of Solid Waste in The Promotion of Culture Environment

    Directory of Open Access Journals (Sweden)

    Isbely del Carmen Aguilera Osorio

    2016-08-01

    Full Text Available This study aimed to propose a strategic plan for the reuse of solid waste in promoting environmental culture in the sixth grade students of Basic Estadal "Chaparral" School, located in the municipality Pedraza Barinas State for the year school from 2015 to 2016. Research of quantitative nature, descriptive in the form of feasible project, divided into five phases for the diagnosis, feasibility, design, implementation and evaluation of results in the implementation of a strategic plan based on the reuse of solid waste. In relation to the population, this is limited to five teachers, selecting all for the sample as a small universe. As the survey technique was used a questionnaire type instrument 8 questions in Likert scale of three response options was applied. For the formula reliability coefficient (α Cronbach's alpha, validity through expert judgment was applied. In conclusion a proposal called Strategic Plan for reuse of solid waste in promoting environmental culture in the sixth grade students of Basic Estadal "Chaparral" School during the 2015-2016 school year was set.

  18. Systematic process synthesis and design methods for cost effective waste minimization

    Energy Technology Data Exchange (ETDEWEB)

    Biegler, L.T.; Grossman, I.E.; Westerberg, A.W. [Carnegie Mellon Univ., Pittsburgh, PA (United States)

    1995-12-31

    We present progress on our work to develop synthesis methods to aid in the design of cost effective approaches to waste minimization. Work continues to combine the approaches of Douglas and coworkers and of Grossmann and coworkers on a hierarchical approach where bounding information allows it to fit within a mixed integer programming approach. We continue work on the synthesis of reactors and of flexible separation processes. In the first instance, we strive for methods we can use to reduce the production of potential pollutants, while in the second we look for ways to recover and recycle solvents.

  19. Use of Linear Programming to Develop Cost-Minimized Nutritionally Adequate Health Promoting Food Baskets

    DEFF Research Database (Denmark)

    Parlesak, A.; Tetens, Inge; Dejgård Jensen, Jørgen

    2016-01-01

    Food-Based Dietary Guidelines (FBDGs) are developed to promote healthier eating patterns, but increasing food prices may make healthy eating less affordable. The aim of this study was to design a range of cost-minimized nutritionally adequate health-promoting food baskets (FBs) that help prevent...... both micronutrient inadequacy and diet-related non-communicable diseases at lowest cost. Average prices for 312 foods were collected within the Greater Copenhagen area. The cost and nutrient content of five different cost-minimized FBs for a family of four were calculated per day using linear...... facilitates the generation of low-cost food baskets that are nutritionally adequate, health promoting, and culturally acceptable....

  20. Waste level analysis in a care section with the lean maintenance method to minimize waste in PT. Varia Usaha Beton Gresik

    Directory of Open Access Journals (Sweden)

    Rochmoeljati Rr.

    2017-06-01

    Full Text Available The major problem faced by PT. Varia Usaha Beton Gresik is not the maintenance activity according to Standard Operation Procedure (SOP, but the activities conducted without taking into account the waste. The purpose of this study is to examine the waste in the maintenance activities as to minimize it by the lean maintenance method. This is taken on a conveyor belt weigher machine, a bucket conveyor, a concrete mixer, and a machine host. The variable is the flow of treatment by reducing waste and by giving recommendation of improvement. Data collection includes damage data, production data, product disability data, and maintenance activity data. The conclusion is QT-10 waste motion machine takes 532 minutes for waste repair, 45 minutes for waste process, and 90 minutes for waste waiting. Our recommendations include improvement on the information provided, on training and rewards, and on supervisors of the production line.

  1. Implementation of Lean Warehouse to Minimize Wastes in Finished Goods Warehouse of PT Charoen Pokphand Indonesia Semarang

    Directory of Open Access Journals (Sweden)

    Nia Budi Puspitasari

    2016-03-01

    Full Text Available PT. Charoen Pokphand Indonesia Semarang is one of the largest poultry feed companies in Indonesia. To store the finished products that are ready to be distributed, it needs a finished goods warehouse. To minimize the wastes that occur in the process of warehousing the finished goods, the implementation of lean warehouse is required. The core process of finished goods warehouse is the process of putting bag that has been through the process of pallets packing, and then transporting the pallets contained bags of feed at finished goods warehouses and the process of unloading food from the finished goods warehouse to the distribution truck. With the implementation of the lean warehouse, we can know whether the activities are value added or not, to be identified later which type of waste happened. Opinions of stakeholders regarding the waste that must be eliminated first need to be determined by questionnaires. Based on the results of the questionnaires, three top wastes are selected to be identified the cause by using fishbone diagram. They can be repaired by using the implementation of 5S, namely Seiri, Seiton, Seiso, Seiketsu, and Shitsuke. Defect waste can be minimized by selecting pallet, putting sack correctly, forklift line clearance, applying working procedures, and creating cleaning schedule. Next, overprocessing waste is minimized by removing unnecessary items, putting based on the date of manufacture, and manufacture of feed plan. Inventory waste is minimized by removing junks, putting feed based on the expired date, and cleaning the barn

  2. Minimizing Onsite Organic Household Left-Over Waste: The Emission Benefits of Keeping Pet Rabbits.

    Directory of Open Access Journals (Sweden)

    Konstantinos P. Tsagarakis

    2017-09-01

    Full Text Available As waste management is becoming all the more crucial, this study investigates the way in which house left-over organic waste can be better managed on site, in order to minimize the off-site treatment cost and maximize environmental performance. For the implementation of this research, a full year measurement was recorded, showing the organic leftover waste food intake of two rabbits in a household of four. The organic food, collected in two separate baskets suitable for composting—though one for rabbit intake—was 168.5 kg in total, plus 68.8 kg, which was delivered directly to the composting bin, along with food remains and rabbit feces. The results show that, over the examined year, a total of up to 0.417 metric tons of CO2 equivalent per year emissions was avoided, suggesting that if 30 houses were to apply this methodology, one garbage truck journey per year would be saved. Overall, this study suggests that better information and environmental awareness can result in on-site, low cost, individual management of recyclable organic material, which would assist with the decrease in the cost of management, along with increased environmental performance.

  3. A case-study of landfill minimization and material recovery via waste co-gasification in a new waste management scheme.

    Science.gov (United States)

    Tanigaki, Nobuhiro; Ishida, Yoshihiro; Osada, Morihiro

    2015-03-01

    This study evaluates municipal solid waste co-gasification technology and a new solid waste management scheme, which can minimize final landfill amounts and maximize material recycled from waste. This new scheme is considered for a region where bottom ash and incombustibles are landfilled or not allowed to be recycled due to their toxic heavy metal concentration. Waste is processed with incombustible residues and an incineration bottom ash discharged from existent conventional incinerators, using a gasification and melting technology (the Direct Melting System). The inert materials, contained in municipal solid waste, incombustibles and bottom ash, are recycled as slag and metal in this process as well as energy recovery. Based on this new waste management scheme with a co-gasification system, a case study of municipal solid waste co-gasification was evaluated and compared with other technical solutions, such as conventional incineration, incineration with an ash melting facility under certain boundary conditions. From a technical point of view, co-gasification produced high quality slag with few harmful heavy metals, which was recycled completely without requiring any further post-treatment such as aging. As a consequence, the co-gasification system had an economical advantage over other systems because of its material recovery and minimization of the final landfill amount. Sensitivity analyses of landfill cost, power price and inert materials in waste were also conducted. The higher the landfill costs, the greater the advantage of the co-gasification system has. The co-gasification was beneficial for landfill cost in the range of 80 Euro per ton or more. Higher power prices led to lower operation cost in each case. The inert contents in processed waste had a significant influence on the operating cost. These results indicate that co-gasification of bottom ash and incombustibles with municipal solid waste contributes to minimizing the final landfill amount and has

  4. Policies to promote the waste management hierarchy : with special attention to the paper cycle in Europe

    OpenAIRE

    Beukering, van, E.J.M.; L.M. Brander

    2004-01-01

    The main objective of this study was to review policy instruments available to promote aspects of the waste management hierarchy. The motivation of this review is embedded in two questions: (1) What policy instruments are most effective in promoting the waste hierarchy? and, (2) Should EU policies in the European paper cycle be harmonised? With respect to the first question, the most effective policy instrument to promote the waste hierarchy for the European paper cycle, it is concluded that ...

  5. Feasibility Studies on Pipeline Disposal of Concentrated Copper Tailings Slurry for Waste Minimization

    Science.gov (United States)

    Senapati, Pradipta Kumar; Mishra, Barada Kanta

    2017-06-01

    The conventional lean phase copper tailings slurry disposal systems create pollution all around the disposal area through seepage and flooding of waste slurry water. In order to reduce water consumption and minimize pollution, the pipeline disposal of these waste slurries at high solids concentrations may be considered as a viable option. The paper presents the rheological and pipeline flow characteristics of copper tailings samples in the solids concentration range of 65-72 % by weight. The tailings slurry indicated non-Newtonian behaviour at these solids concentrations and the rheological data were best fitted by Bingham plastic model. The influence of solids concentration on yield stress and plastic viscosity for the copper tailings samples were discussed. Using a high concentration test loop, pipeline experiments were conducted in a 50 mm nominal bore (NB) pipe by varying the pipe flow velocity from 1.5 to 3.5 m/s. A non-Newtonian Bingham plastic pressure drop model predicted the experimental data reasonably well for the concentrated tailings slurry. The pressure drop model was used for higher size pipes and the operating conditions for pipeline disposal of concentrated copper tailings slurry in a 200 mm NB pipe with respect to specific power consumption were discussed.

  6. Analysis of critical features and evaluation of BIM software: Towards a plug-in for construction waste minimization using big data

    OpenAIRE

    Bilal, M.; Oyedele, L.; Qadir, J.; Munir, K; Akinade, O.; Ajayi, S. ed; Alaka, H. A.; Owolabi, H. A.

    2015-01-01

    The overall aim of this study is to investigate the potential of Building Information Modelling (BIM) for construction waste minimization. We evaluated the leading BIM design software products and concluded that none of them currently support construction waste minimization. This motivates the development of a plug-in for predicting and minimizing construction waste. After a rigorous literature review and conducting four focused group interviews (FGIs), 12 imperative BIM factors were identifi...

  7. Policies to promote the waste management hierarchy : with special attention to the paper cycle in Europe

    NARCIS (Netherlands)

    Beukering, van P.J.H.; Brander, L.M.

    2004-01-01

    The main objective of this study was to review policy instruments available to promote aspects of the waste management hierarchy. The motivation of this review is embedded in two questions: (1) What policy instruments are most effective in promoting the waste hierarchy? and, (2) Should EU policies

  8. Use of Linear Programming to Develop Cost-Minimized Nutritionally Adequate Health Promoting Food Baskets.

    Science.gov (United States)

    Parlesak, Alexandr; Tetens, Inge; Dejgård Jensen, Jørgen; Smed, Sinne; Gabrijelčič Blenkuš, Mojca; Rayner, Mike; Darmon, Nicole; Robertson, Aileen

    2016-01-01

    Food-Based Dietary Guidelines (FBDGs) are developed to promote healthier eating patterns, but increasing food prices may make healthy eating less affordable. The aim of this study was to design a range of cost-minimized nutritionally adequate health-promoting food baskets (FBs) that help prevent both micronutrient inadequacy and diet-related non-communicable diseases at lowest cost. Average prices for 312 foods were collected within the Greater Copenhagen area. The cost and nutrient content of five different cost-minimized FBs for a family of four were calculated per day using linear programming. The FBs were defined using five different constraints: cultural acceptability (CA), or dietary guidelines (DG), or nutrient recommendations (N), or cultural acceptability and nutrient recommendations (CAN), or dietary guidelines and nutrient recommendations (DGN). The variety and number of foods in each of the resulting five baskets was increased through limiting the relative share of individual foods. The one-day version of N contained only 12 foods at the minimum cost of DKK 27 (€ 3.6). The CA, DG, and DGN were about twice of this and the CAN cost ~DKK 81 (€ 10.8). The baskets with the greater variety of foods contained from 70 (CAN) to 134 (DGN) foods and cost between DKK 60 (€ 8.1, N) and DKK 125 (€ 16.8, DGN). Ensuring that the food baskets cover both dietary guidelines and nutrient recommendations doubled the cost while cultural acceptability (CAN) tripled it. Use of linear programming facilitates the generation of low-cost food baskets that are nutritionally adequate, health promoting, and culturally acceptable.

  9. Use of Linear Programming to Develop Cost-Minimized Nutritionally Adequate Health Promoting Food Baskets.

    Directory of Open Access Journals (Sweden)

    Alexandr Parlesak

    Full Text Available Food-Based Dietary Guidelines (FBDGs are developed to promote healthier eating patterns, but increasing food prices may make healthy eating less affordable. The aim of this study was to design a range of cost-minimized nutritionally adequate health-promoting food baskets (FBs that help prevent both micronutrient inadequacy and diet-related non-communicable diseases at lowest cost.Average prices for 312 foods were collected within the Greater Copenhagen area. The cost and nutrient content of five different cost-minimized FBs for a family of four were calculated per day using linear programming. The FBs were defined using five different constraints: cultural acceptability (CA, or dietary guidelines (DG, or nutrient recommendations (N, or cultural acceptability and nutrient recommendations (CAN, or dietary guidelines and nutrient recommendations (DGN. The variety and number of foods in each of the resulting five baskets was increased through limiting the relative share of individual foods.The one-day version of N contained only 12 foods at the minimum cost of DKK 27 (€ 3.6. The CA, DG, and DGN were about twice of this and the CAN cost ~DKK 81 (€ 10.8. The baskets with the greater variety of foods contained from 70 (CAN to 134 (DGN foods and cost between DKK 60 (€ 8.1, N and DKK 125 (€ 16.8, DGN. Ensuring that the food baskets cover both dietary guidelines and nutrient recommendations doubled the cost while cultural acceptability (CAN tripled it.Use of linear programming facilitates the generation of low-cost food baskets that are nutritionally adequate, health promoting, and culturally acceptable.

  10. USER'S GUIDE: Strategic Waste Minimization Initiative (SWAMI) Version 2.0 - A Software Tool to Aid in Process Analysis for Pollution Prevention

    Science.gov (United States)

    The Strategic WAste Minimization Initiative (SWAMI) Software, Version 2.0 is a tool for using process analysis for identifying waste minimization opportunities within an industrial setting. The software requires user-supplied information for process definition, as well as materia...

  11. Analysis of the application of decontamination technologies to radioactive metal waste minimization using expert systems

    Energy Technology Data Exchange (ETDEWEB)

    Bayrakal, Suna [Iowa State Univ., Ames, IA (United States)

    1993-09-30

    Radioactive metal waste makes up a significant portion of the waste currently being sent for disposal. Recovery of this metal as a valuable resource is possible through the use of decontamination technologies. Through the development and use of expert systems a comparison can be made of laser decontamination, a technology currently under development at Ames Laboratory, with currently available decontamination technologies for applicability to the types of metal waste being generated and the effectiveness of these versus simply disposing of the waste. These technologies can be technically and economically evaluated by the use of expert systems techniques to provide a waste management decision making tool that generates, given an identified metal waste, waste management recommendations. The user enters waste characteristic information as input and the system then recommends decontamination technologies, determines residual contamination levels and possible waste management strategies, carries out a cost analysis and then ranks, according to cost, the possibilities for management of the waste. The expert system was developed using information from literature and personnel experienced in the use of decontamination technologies and requires validation by human experts and assignment of confidence factors to the knowledge represented within.

  12. Identification of the minimal melanocyte-specific promoter in the melanocortin receptor 1 gene

    Directory of Open Access Journals (Sweden)

    Natali Pier

    2008-11-01

    Full Text Available Abstract Background The understanding of cutaneous pigmentation biology is relevant from the biologic and clinical point of view. The binding of α-melanocortin and its specific receptor, on the plasma membrane of melanin synthesising cells, plays a crucial role in melanins biosynthesis. Furthermore, loss of MC1R function is associated with an increased incidence of melanoma and non-melanoma skin cancer. The expression of the α-melanocortin receptor gene is highly controlled but, at the present, region responsible for tissue-specific activity of the gene promoter has not been identified. Methods We have cloned the genomic sequences upstream the human MC1R coding gene. A DNA fragment of 5 kilobases upstream the human MC1R encoding sequence was placed in front of a reporter gene and several deletion mutants of such fragment have been prepared. These constructs have been tested for the ability to drive the melanocyte-specific gene expression of the reporter gene using transfection experiments in melanocyte and non-melanocyte cell lines. From these experiments we identified a DNA fragment with the ability to drive the gene transcription in a tissue-specific way and we used this small DNA fragment in DNA-protein interaction assays. Results We show that the 150 base pairs upstream the MC1R gene initiation codon are able to drive the melanocyte-specific gene transcription. Furthermore, we provide experimental evidences suggesting that on such minimal melanocyte-specific gene promoter can assemble tissue-specific complexes. Conclusion The present results strongly imply that the transcriptional regulation of the melanocyte-specific MC1R gene requires an internal promoter located in the 150 base pairs upstream the initiation codon.

  13. Wastes Management Can Minimize CH4 and N2O Emissions from Wetlands in Indonesia

    Directory of Open Access Journals (Sweden)

    Abdul Hadi

    2015-07-01

    Full Text Available Paddy (Oriza sativa L. and Oil palm (Elaeis guineensis Jack are two important crops and are potential to produce wastes which may lead to huge greenhouse gas emissions if they are not managed properly.  Open burning and conventional composting are commonly practiced by farmers and/or planters to managed agricultural wastes in Indonesia.  A series of research has been carried out  to elucidate (1 the reductions of CH4 and N2O due to incertion of a catalitic converter on burning kiln, (2 the best composting technique of oil palm field wastes, and (3 the effects of oil palm field wastes compost application in oil palm fields and of paddy field wastes biochar in integrated oil palm-paddy fields.  The results showed that CH4 and N2O emissions from paddy field wastes (i.e., rice straw or rice husk was lower than that from oil palm empty fruit bunch (EFB.  Furthermore, insertion of a catalytic converter into pyrolysis installation reduced the CO2, CH4 and N2O emissions from paddy field wastes as much as 14.5, 17.8 and 11.1%, respectively.  Incorporation of EFB compost did not increase greenhouse gas emission from oil palm fields. These results suggest that biochar and EFB compost can be practiced to manage agricultural wastes in Indonesia.

  14. Application of molten salt oxidation for the minimization and recovery of plutonium-238 contaminated wastes

    Energy Technology Data Exchange (ETDEWEB)

    Wishau, R.

    1998-05-01

    Molten salt oxidation (MSO) is proposed as a {sup 238}Pu waste treatment technology that should be developed for volume reduction and recovery of {sup 238}Pu and as an alternative to the transport and permanent disposal of {sup 238}Pu waste to the WIPP repository. In MSO technology, molten sodium carbonate salt at 800--900 C in a reaction vessel acts as a reaction media for wastes. The waste material is destroyed when injected into the molten salt, creating harmless carbon dioxide and steam and a small amount of ash in the spent salt. The spent salt can be treated using aqueous separation methods to reuse the salt and to recover 99.9% of the precious {sup 238}Pu that was in the waste. Tests of MSO technology have shown that the volume of combustible TRU waste can be reduced by a factor of at least twenty. Using this factor the present inventory of 574 TRU drums of {sup 238}Pu contaminated wastes is reduced to 30 drums. Further {sup 238}Pu waste costs of $22 million are avoided from not having to repackage 312 of the 574 drums to a drum total of more than 4,600 drums. MSO combined with aqueous processing of salts will recover approximately 1.7 kilograms of precious {sup 238}Pu valued at 4 million dollars (at $2,500/gram). Thus, installation and use of MSO technology at LANL will result in significant cost savings compared to present plans to transport and dispose {sup 238}Pu TRU waste to the WIPP site. Using a total net present value cost for the MSO project as $4.09 million over a five-year lifetime, the project can pay for itself after either recovery of 1.6 kg of Pu or through volume reduction of 818 drums or a combination of the two. These savings show a positive return on investment.

  15. Waste minimization activities in Toyota Motor Corporation; Haikibutsu teigen eno torikumi jokyo

    Energy Technology Data Exchange (ETDEWEB)

    Taguchi, S.; Yamamoto, N.; Kurai, H. [Toyota Motor Corp., Aichi (Japan)

    1998-07-01

    Toyota`s waste reduction efforts based on a drive for dealing with the source of waste generation are introduced. For the propulsion of the policy for dealing directly with the origin of waste, it is necessary to convert the existing manufacturing processes that give high priority to product quality and low production cost into environmental impact reduction oriented processes. In particular, conversion of materials into those that are easier to recycle, technology for reducing defective products, technology for the completion of recycling within the process involved, and the simplification of all the processes are mentioned. For the cleaning job in the machining process, a detergent enhanced in oil/water separating capability is developed, and this prolongs doubly the detergent replacement period and decreases the waste liquid to a 1/4 or less of what the conventional method produces. For the handling of foundry sand that is yielded in great quantities, a flow classification system is developed to replace the conventional gravitational classifier, and the reusable coarse-grain sand in the collected dust which occupies approximately 70% of the whole waste is now recovered for reuse. In the vehicle body coating process, a newly-developed robot arm type coating system is developed, which halves the coating waste. 2 refs., 9 figs., 1 tab.

  16. [Promoting the sustainable management of hospital waste in Kinshasa].

    Science.gov (United States)

    Kasuku, Wanduma; Bouland, Catherine; De Brouwer, Christophe; Mareschal, Bertrand; Mulaji, Crispin

    2016-11-01

    The management of hospital waste is a high-risk practice in the hospitals of Kinshasa, the largest city of the Democratic Republic of the Congo, from the point of view of public health and the environment. A multi-criteria study carried out in 4 hospitals assessed the situation and put forward solutions. Copyright © 2016. Publié par Elsevier Masson SAS.

  17. Application of AHP for the development of waste management systems that minimize infection risks in developing countries: Case studies Lesotho and South Africa

    CSIR Research Space (South Africa)

    Brent, AC

    2006-09-01

    Full Text Available This paper focuses on the establishment of waste management systems that minimize infection risks in the context of sustainable development in the developing country situations. The Analytical Hierarchy Process (AHP), a known multi-criteria decision...

  18. A Participatory Approach to Minimizing Food Waste in the Food Industry—A Manual for Managers

    Directory of Open Access Journals (Sweden)

    Christina Strotmann

    2017-01-01

    Full Text Available Based on their experiences gained in 15 companies in the catering sector and the bakery industry, the authors present a participatory concept to reduce food waste in the food industry. This five-phase concept, adapted to the PDCA (Plan–Do–Check–Act cycle applied in the Total Quality Management, involves a participatory approach where employees are integrated into the process of developing and implementing measures to counteract food waste. The authors describe how the participatory approach can be used to raise awareness of the topic of food waste to improve employee commitment and responsibility. As a result, the authors further offer a Manual for Managers wishing to reduce food waste in their respective organizations. This manual includes information on the methodologies applied in each step of the improvement cycle. It also describes why the steps are necessary, and how results can be documented. The participatory concept and the Manual for Managers contribute to reducing food waste and to enhancing resource efficiency in the food industry.

  19. Emissions minimization of chlorinated micropollutants in coal solid waste co-combustion by primary measures

    Energy Technology Data Exchange (ETDEWEB)

    Pandelova, M.; Lenoir, D.; Schramm, K.W. [GSF-Forschungszentrum fuer Umwelt und Gesundheit GmbH, Neuherberg (Germany)

    2005-07-01

    This study addresses co-combustion of coal-solid waste mixtures in pilot and laboratory-scale combustors, with emphasis on monitoring of toxic chlorinated hydrocarbon emissions like: polychlorinated dibenzo-p-dioxins (PCDD), polychlorinated dibenzofurans (PCDF), polychlorinated biphenyls (PCB) and polychlorinated benzenes (PCBz). The objectives of the work are stress on the so-called primary measures technique which cause reduction of the toxic emission prior formation the chlorinated micropollutants. Thermally resistant inorganic compounds were added directly to the fuel. The fuel-types used in this study are lignite coal from Puertollano (CIEMAT, Spain), pre-treated municipal solid waste (Rethmann Plano GmbH) and PVC (waste from ground floor). Two low cost and non- toxic nitrogen- and sulfur-compounds were considered as the most effective inhibitors for PCDD/F formation. That makes them applicable for use in a full scale combustion unit. (orig.)

  20. Proceedings of waste stream minimization and utilization innovative concepts: An experimental technology exchange. Volume 2, Industrial liquid waste processing, industrial gaseous waste processing

    Energy Technology Data Exchange (ETDEWEB)

    Lee, V.E. [ed.; Watts, R.L.

    1993-04-01

    This two-volume proceedings summarize the results of fifteen innovations that were funded through the US Department of Energy`s Innovative Concept Program. The fifteen innovations were presented at the sixth Innovative Concepts Fair, held in Austin, Texas, on April 22--23, 1993. The concepts in this year`s fair address innovations that can substantially reduce or use waste streams. Each paper describes the need for the proposed concept, the concept being proposed, and the concept`s economics and market potential, key experimental results, and future development needs. The papers are divided into two volumes: Volume 1 addresses innovations for industrial solid waste processing and municipal waste reduction/recycling, and Volume 2 addresses industrial liquid waste processing and industrial gaseous waste processing. Individual reports are indexed separately.

  1. Proceedings of waste stream minimization and utilization innovative concepts: An experimental technology exchange. Volume 1, Industrial solid waste processing municipal waste reduction/recycling

    Energy Technology Data Exchange (ETDEWEB)

    Lee, V.E. [ed.; Watts, R.L.

    1993-04-01

    This two-volume proceedings summarizes the results of fifteen innovations that were funded through the US Department of Energy`s Innovative Concept Program. The fifteen innovations were presented at the sixth Innovative Concepts Fair, held in Austin, Texas, on April 22--23, 1993. The concepts in this year`s fair address innovations that can substantially reduce or use waste streams. Each paper describes the need for the proposed concept, the concept being proposed, and the concept`s economics and market potential, key experimental results, and future development needs. The papers are divided into two volumes: Volume 1 addresses innovations for industrial solid waste processing and municipal waste reduction/recycling, and Volume 2 addresses industrial liquid waste processing and industrial gaseous waste processing. Selected papers have been indexed separately for inclusion in the Energy Science and Technology Database.

  2. POLLUTION PREVENTION STRATEGIES FOR THE MINIMIZING OF INDUSTRIAL WASTES IN THE VCM-PVC INDUSTRY

    Science.gov (United States)

    In many U.S. companies, pollution prevention strategies coincide with economic interests. Typically a company strives to be the lowest-cost producer, to be competitive, and to reduce wastes. In this paper, the author reviews pollution prevention strategies in the vinyl chloride m...

  3. Status and direction of waste minimization in the chemical and petrochemical industries

    Energy Technology Data Exchange (ETDEWEB)

    Englande Junior, A.J. [Tulane Univ., New Orleans, LA (United States). School of Public Health and Tropical Medicine

    1993-12-31

    This paper presents an evaluation of the status and direction of toxic/hazardous waste reduction in chemical and petrochemical industries from an international perspective. In almost all cases studied savings have resulted. The importance of pollution prevention by `clean technologies` instead of remediation is stressed. 6 refs., 4 tabs.

  4. Minimization of actinide waste by multi-recycling of thoriated fuels in the EPR reactor

    Directory of Open Access Journals (Sweden)

    Nuttin A.

    2012-02-01

    Full Text Available The multi-recycling of innovative uranium/thorium oxide fuels for use in the European Pressurized water Reactor (EPR has been investigated. If increasing quantities of 238U, the fertile isotope in standard UO2 fuel, are replaced by 232Th, then a greater yield of new fissile material (233U is produced during the cycle than would otherwise be the case. This leads to economies of natural uranium of around 45% if the uranium in the spent fuel is multi-recycled. In addition we show that minor actinide and plutonium waste inventories are reduced and hence waste radio-toxicities and decay heats are up to a factor of 20 lower after 103 years. Two innovative fuel types named S90 and S20, ThO2 mixed with 90% and 20% enriched UO2 respectively, are compared as an alternative to standard uranium oxide (UOX and uranium/plutonium mixed oxide (MOX fuels at the longest EPR fuel discharge burn-ups of 65 GWd/t. Fissile and waste inventories are examined, waste radio-toxicities and decay heats are extracted and safety feedback coefficients are calculated.

  5. Removal of contaminants from equipment and debris and waste minimization using TechXtract{reg_sign} technology

    Energy Technology Data Exchange (ETDEWEB)

    Bonem, M.W. [EET, Inc., Bellaire, TX (United States)

    1997-10-01

    Under this Program Research and Development Agreement (PRDA), EET, Inc., is extending its proprietary TechXtract{reg_sign} chemical decontamination technology into an effective, economical, integrated contaminant removal system. This integrated system will consist of a series of decontamination baths using the TechXtract{reg_sign} chemical formulas, followed by a waste treatment process that will remove the contaminants from the spent chemicals. Sufficient decontamination will result so that materials can be released without restriction after they have been treated, even those materials that have traditionally been considered to be {open_quotes}undecontaminable.{close_quotes} The secondary liquid waste will then be treated to separate any hazardous and radioactive contaminants, so that the spent chemicals and wastewater can be discharged through conventional, permitted outlets. The TechXtract{reg_sign} technology is a unique process that chemically extracts hazardous contaminants from the surface and substrate of concrete, steel, and other solid materials. This technology has been used successfully to remove contaminants as varied as PCBs, radionuclides, heavy metals, and hazardous organics. The process` advantage over other alternatives is its effectiveness in safe and consistent extraction of subsurface contamination. TechXtract{reg_sign} is a proprietary process developed, owned, and provided by EET, Inc. The objective of the PRDA is to demonstrate on a full-scale basis an economical system for decontaminating equipment and debris, with further treatment of secondary waste streams to minimize waste volumes. Contaminants will be removed from the contaminated items to levels where they can be released for unrestricted use. The entire system will be designed with maximum flexibility and automation in mind.

  6. Conversion of finished leather waste incorporated with plant fibers into value added consumer products - An effort to minimize solid waste in Ethiopia.

    Science.gov (United States)

    Teklay, A; Gebeyehu, G; Getachew, T; Yaynshet, T; Sastry, T P

    2017-10-01

    Presently, the leftovers from leather product industries are discarded as waste in Ethiopia. The objective of the present study was therefore, to prepare composite sheets by incorporating various plant fibers like enset (Ensete ventricosum), hibiscus (Hibiscus cannabinus), jute (Corchorus trilocularis L.), palm (Phoenix dactylifera) and sisal (Agave sisal) in various proportions into the leather waste. Resin binder (RB) and natural rubber latex (NRL) were used as binding agents for the preparation of the composite sheets. The composite sheets prepared were characterized for their physicochemical properties (tensile strength, elongation at break, stitch tear strength, water absorption, water desorption and flexing strength). Composite sheets prepared using RB having 10% hibiscus, 20% palm and 40% sisal fibers showed better mechanical properties than their respective controls. In composite sheets prepared using NRL having 30% jute fiber exhibited better mechanical properties than its control. Most of the plant fibers used in this study played a role in increasing the performance of the sheets. However, as seen from the results, the contribution of these plant fibers on performance of the composite sheets prepared is dependent on the ratio used and the nature of binder. The SEM studies have exhibited the composite nature of the sheets and FTIR studies have shown the functional groups of collagen protein, cellulose and binders. The prepared sheets were used as raw materials for preparation of items like stiff hand bags, ladies' purse, keychain, chappal upper, wallet, wall cover, mouse pad and other interior decorating products. By preparing such value added products, we can reduce solid waste; minimize environmental pollution and thereby securing environmental sustainability. Copyright © 2017 Elsevier Ltd. All rights reserved.

  7. Ectopic integration vectors for generating fluorescent promoter fusions in Bacillus subtilis with minimal dark noise.

    Directory of Open Access Journals (Sweden)

    Stephanie Trauth

    Full Text Available Fluorescent protein promoter reporters are important tools that are widely used for diverse purposes in microbiology, systems biology and synthetic biology and considerable engineering efforts are still geared at improving the sensitivity of the reporter systems. Here we focus on dark noise, i.e. the signal that is generated by the empty vector control. We quantitatively characterize the dark noise of a few common bacterial reporter systems by single cell microscopy. All benchmarked reporter systems generated significant amounts of dark noise that exceed the cellular autofluorescence to different extents. We then reengineered a multicolor set of fluorescent ectopic integration vectors for Bacillus subtilis by introducing a terminator immediately upstream of the promoter insertion site, resulting in an up to 2.7-fold reduction of noise levels. The sensitivity and dynamic range of the new high-performance pXFP_Star reporter system is only limited by cellular autofluorescence. Moreover, based on studies of the rapE promoter of B. subtilis we show that the new pXFP_Star reporter system reliably reports on the weak activity of the rapE promoter whereas the original reporter system fails because of transcriptional interference. Since the pXFP_Star reporter system properly isolates the promoter from spurious transcripts, it is a particularly suitable tool for quantitative characterization of weak promoters in B. subtilis.

  8. New synthetic approaches in energetic materials field to minimize waste production

    Energy Technology Data Exchange (ETDEWEB)

    Kwok, T.J.; Jayasuriya, K. [US Army ARDEC, Picatinny Arsenal, NJ (United States)

    1995-12-31

    The nitration of aromatic compounds is an important process in both industrial and academic research. In particular, the nitration of toluene is found to be useful for producing military explosives such as 2,4,6-trinitrotoluene (TNT) and pharmaceutical intermediates such as para-aminobenzoic acid (PABA). The conventional methods for nitration of aromatic compounds require corrosive nitric and sulfuric acids that afford a mixture of mono and poly-nitroaromatics. Under these conditions, the nitration of alkyl substituted aromatics such as toluene or xylenes, often leads to oxidation of the alkyl side groups, and this could produce a mixture of by-products. Developments in solid acid catalysts such as Nafion and other polysulfonic acid resins have reduced the corrosive nature and by-product formation of the existing process. However, the separation and removal of unwanted isomers from the product stream can be costly. Unfortunately, these sulfonic acid resin catalysts offer no significant contribution toward controlling regioselection in mononitration of alkyl aromatics such as toluene. The para-nitrotoluene isomer is highly desirable over the ortho and meta isomers because of its high commercial value. Current trends in the nitration of aromatic compounds emphasize minimizing by-product formation and improving region-control of the desired isomer product using catalysts. Zeclites have well defined pore structures and channels that are derived from the networking of SiO{sub 2} and Al{sub 2}O{sub 3} making them attractive candidates for shape selective catalysis. In most cases zeolites are found to have both Lewis and Bronstead acidic sites throughout the inner and outer surfaces that can function as a solid acid. This would be advantageous in large preparative scale reactions because of the ease in separation of catalyst from the product mixture and having minimal environmental impact.

  9. Minimizing the Moisture Damage and Drain down of Iraqi SMA Mixtures Using Waste Additives

    Directory of Open Access Journals (Sweden)

    Ali Al-Hadidy

    2013-04-01

    Full Text Available This research deals with the viability of using polyester fiber (PF, crumb rubber tire (CRT and cellulose fiber (CF as stabilizing waste additives in producing Iraqi SMA mixtures that sustain drain down phenomenon and moisture damage sensitivity. Different ratios of these additives (0.1, 0.2, and 0.3% by weight of aggregate and filler were mixed with 40/50 paving asphalt by means of dry process. Unmodified and modified SMA mixtures were subjected to drain down, Marshall, static indirect tensile strength, tensile stiffness modulus, static compressive strength, tensile strength ratio and index of retained strength tests. A set of regression equations between these tests were established. In addition, an optimization table based on these tests, which can be used to select the type or amount of additive for any field applications has been determined and reported. The results indicated that the inclusion of these additives in SMA mixtures can satisfy the performance requirement of high temperature and much rain zone.

  10. Solid Waste Management Consortium: An Instrument of Integration and Promotion of Sustainable Development

    Directory of Open Access Journals (Sweden)

    Allexandre Guimarães Trindade

    2016-12-01

    Full Text Available Solid waste is a historic vulnerability of Brazilian society, that even with the during of National Policy of Solid Waste, Law n. 12.305/2010, the country faces major challenges, for its management. In this sense, the present article aims to demonstrate, by the method of dialectical approach that the management intercropped is the most suitable instrument to promote integrated management desired by Law n. 12.305/2010. This is a tool creates an integrated governance in actions of urban development, toward improving the quality of life, employment and income generations, expense savings, social participation and environmental justice.

  11. "I Can't Lie to Your Face": Minimal Face-to-Face Interaction Promotes Honestry

    OpenAIRE

    Van Zant, Alex B.; Kray, Laura J.

    2013-01-01

    In the current research, we consider how gender composition may impact the likelihood of deception in contexts with asymmetric information where one party has the opportunity to strategically deceive another party for the opportunity to gain economically. We predict that the combined processes of social categorization and social projection should make people more likely to presume trust from same-gender others than different-gender others. Because anonymous interactions promote the tendency t...

  12. Use of Linear Programming to Develop Cost-Minimized Nutritionally Adequate Health Promoting Food Baskets

    DEFF Research Database (Denmark)

    Parlesak, A.; Tetens, Inge; Dejgård Jensen, Jørgen

    2016-01-01

    variety of foods contained from 70 (CAN) to 134 (DGN) foods and cost between DKK 60 (€ 8.1, N) and DKK 125 (€ 16.8, DGN). Ensuring that the food baskets cover both dietary guidelines and nutrient recommendations doubled the cost while cultural acceptability (CAN) tripled it. Use of linear programming...... both micronutrient inadequacy and diet-related non-communicable diseases at lowest cost. Average prices for 312 foods were collected within the Greater Copenhagen area. The cost and nutrient content of five different cost-minimized FBs for a family of four were calculated per day using linear...... programming. The FBs were defined using five different constraints: cultural acceptability (CA), or dietary guidelines (DG), or nutrient recommendations (N), or cultural acceptability and nutrient recommendations (CAN), or dietary guidelines and nutrient recommendations (DGN). The variety and number of foods...

  13. Strategies to promote a climate of academic integrity and minimize student cheating and plagiarism.

    Science.gov (United States)

    Scanlan, Craig L

    2006-01-01

    Student academic misconduct is a growing problem for colleges and universities, including those responsible for preparing health professionals. Although the implementation of honor codes has had a positive impact on this problem, further reduction in student cheating and plagiarism can be achieved only via a comprehensive strategy that promotes an institutional culture of academic integrity. Such a strategy must combine efforts both to deter and detect academic misconduct, along with fair but rigorous application of sanctions against such behaviors. Methods useful in preventing or deterring dishonest behaviors among students include early integrity training complemented with course-level reinforcement, faculty role-modeling, and the application of selected testing/assignment preventive strategies, including honor pledges and honesty declarations. Giving students more responsibility for oversight of academic integrity also may help address this problem and better promote the culture needed to uphold its principles. Successful enforcement requires that academic administration provide strong and visible support for upholding academic integrity standards, including the provision of a clear and fair process and the consistent application of appropriate sanctions against those whose conduct is found to violate these standards.

  14. Waste management and climate protection. Contribution of Bavarian waste management for greenhouse gas minimization; Abfallwirtschaft und Klimaschutz. Beitrag der bayerischen Abfallwirtschaft zur Treibhausgas-Minderung

    Energy Technology Data Exchange (ETDEWEB)

    Peche, R.; Kreibe, S. [bifa Umweltinstitut, Augsburg (Germany)

    2007-08-15

    bifa created a material flow model for approximately 23 million tons of Bavarian municipal and industrial waste that incorporates collection of waste, waste disposal and processing and treatment of residual material. bifa determined the influence of these material flows on emissions of greenhouse gases. The analysis shows that the Bavarian waste management achieved a reduction of greenhouse gases in the municipal and industrial waste sector that amounted to 3.2 million tons of carbon dioxide equivalents (CO{sub 2}E) in 2003, thus reducing environmental impact considerably. To see the overall reduction of greenhouse gases it is however necessary to compare the system of waste collection, waste treatment and waste processing with a fictitious scenario of waste disposal exclusively via landfill. This would cause an environmental load of 9.58 million tons CO{sub 2}E. Together with the amount of reduction attained in 2003, an overall reduction of greenhouse gas emissions of 12.78 millions tons CO{sub 2}E has thus been achieved by the Bavarian waste management. Analysis of possible future waste processing and waste avoidance measures showed two areas with significant additional potential for the reduction of greenhouse gas emissions. One is waste avoidance - e. g. through increased municipal counselling - however, this is difficult to realize. The other possibility is the optimisation of bio-waste processing. (orig.)

  15. Requirement analysis to promote small-sized E-waste collection from consumers.

    Science.gov (United States)

    Mishima, Kuniko; Nishimura, Hidekazu

    2016-02-01

    The collection and recycling of small-sized waste electrical and electronic equipment is an emerging problem, since these products contain certain amounts of critical metals and rare earths. Even if the amount is not large, having a few supply routes for such recycled resources could be a good strategy to be competitive in a world of finite resources. The small-sized e-waste sometimes contains personal information, therefore, consumers are often reluctant to put them into recycling bins. In order to promote the recycling of E-waste, collection of used products from the consumer becomes important. Effective methods involving incentives for consumers might be necessary. Without such methods, it will be difficult to achieve the critical amounts necessary for an efficient recycling system. This article focused on used mobile phones among information appliances as the first case study, since it contains relatively large amounts of valuable metals compared with other small-sized waste electrical and electronic equipment and there are a large number of products existing in the market. The article carried out surveys to determine what kind of recycled material collection services are preferred by consumers. The results clarify that incentive or reward money alone is not a driving force for recycling behaviour. The article discusses the types of effective services required to promote recycling behaviour. The article concludes that securing information, transferring data and providing proper information about resources and environment can be an effective tool to encourage a recycling behaviour strategy to promote recycling, plus the potential discount service on purchasing new products associated with the return of recycled mobile phones. © The Author(s) 2015.

  16. A Critical Review of the Recent Improvements in Minimizing Nuclear Waste by Innovative Gas-Cooled Reactors

    Directory of Open Access Journals (Sweden)

    E. Bomboni

    2008-01-01

    Full Text Available This paper presents a critical review of the recent improvements in minimizing nuclear waste in terms of quantities, long-term activities, and radiotoxicities by innovative GCRs, with particular emphasis to the results obtained at the University of Pisa. Regarding these last items, in the frame of some EU projects (GCFR, PUMA, and RAPHAEL, we analyzed symbiotic fuel cycles coupling current LWRs with HTRs, finally closing the cycle by GCFRs. Particularly, we analyzed fertile-free and Pu-Th-based fuel in HTR: we improved plutonium exploitation also by optimizing Pu/Th ratios in the fuel loaded in an HTR. Then, we chose GCFRs to burn residual MA. We have started the calculations on simplified models, but we ended them using more “realistic” models of the reactors. In addition, we have added the GCFR multiple recycling option using keff calculations for all the reactors. As a conclusion, we can state that, coupling HTR with GCFR, the geological disposal issues concerning high-level radiotoxicity of MA can be considerably reduced.

  17. Decomposition Mechanism and Decomposition Promoting Factors of Waste Hard Metal for Zinc Decomposition Process (ZDP)

    Energy Technology Data Exchange (ETDEWEB)

    Pee, J H; Kim, Y J; Kim, J Y; Cho, W S; Kim, K J [Whiteware Ceramic Center, KICET (Korea, Republic of); Seong, N E, E-mail: pee@kicet.re.kr [Recytech Korea Co., Ltd. (Korea, Republic of)

    2011-10-29

    Decomposition promoting factors and decomposition mechanism in the zinc decomposition process of waste hard metals which are composed mostly of tungsten carbide and cobalt were evaluated. Zinc volatility amount was suppressed and zinc steam pressure was produced in the reaction graphite crucible inside an electric furnace for ZDP. Reaction was done for 2 hrs at 650 deg. C, which 100% decomposed the waste hard metals that were over 30 mm thick. As for the separation-decomposition of waste hard metals, zinc melted alloy formed a liquid composed of a mixture of {gamma}-{beta}1 phase from the cobalt binder layer (reaction interface). The volume of reacted zone was expanded and the waste hard metal layer was decomposed-separated horizontally from the hard metal. Zinc used in the ZDP process was almost completely removed-collected by decantation and volatilization-collection process at 1000 deg. C. The small amount of zinc remaining in the tungsten carbide-cobalt powder which was completely decomposed was fully removed by using phosphate solution which had a slow cobalt dissolution speed.

  18. Wasted (wst) mice have 3-bp deletion in the PCNA promoter

    Energy Technology Data Exchange (ETDEWEB)

    Paunesku, T.; Woloschak, G.E. [Argonne National Lab., IL (United States). Center for Mechanistic Biology and Biotechnology

    1997-08-01

    Mice homozygous for the autosomal recessive wasted mutation (wst/wst) have abnormalities in T-lymphocytes and in the anterior motor neuron cells of the spinal cord, leading to sensitivity to ionizing radiation, hind limb paralysis, and immunodeficiency. This defect results in a failure to gain weight by 20 days and death at 28 days of age. Previous results from the authors` group have shown that (1) wasted mice have little if any detectable PCNA protein or mRNA in thymus, but levels in liver, brain, and other tissues are similar to those in controls; and (2) the coding region for PCNA is the same in wasted mice and in control littermates. These observations gave rise to the present study, in which the PCNA promoter was sequenced for wst/wst mice, control littermates ({center_dot}wst/+) and BCF{sub 1} (or BALB/c x C57BL/6) F{sub 1} controls. Sequence analysis revealed only one difference between wst/wst and BALB/c x C57BL/6 F{sub 1} littermates: a 3-bp deletion in the 5 foot upstream region of the PCNA gene of wasted mice that was observed on only one allele or no alleles of normal littermates. The mutated sites in PCNA promoter from two litters plus two additional wst/wst and two known wst/+ animals were screened with 8G and 11G probes, and each confirmed this pattern. The short term DNA segment encompassing the deletion was shown in gel shift experiments to bind a nuclear protein(s) present in a broad variety of cells including thymus and spleen nuclear extract from wst/wst and control mice. The mutated oligomer that was homozygous only in wst/wst mice was not able to bind the same nuclear protein(s).

  19. Discarded oranges and brewer's spent grains as promoting ingredients for microbial growth by submerged and solid state fermentation of agro-industrial waste mixtures.

    Science.gov (United States)

    Aggelopoulos, Theodoros; Bekatorou, Argyro; Pandey, Ashok; Kanellaki, Maria; Koutinas, Athanasios A

    2013-08-01

    The exploitation of various agro-industrial wastes for microbial cell mass production of Kluyveromyces marxianus, kefir, and Saccharomyces cerevisiae is reported in the present investigation. Specifically, the promotional effect of whole orange pulp on cell growth in mixtures consisting of cheese whey, molasses, and potato pulp in submerged fermentation processes was examined. A 2- to 3-fold increase of cell mass was observed in the presence of orange pulp. Likewise, the promotional effect of brewer's spent grains on cell growth in solid state fermentation of mixtures of whey, molasses, potato pulp, malt spent rootlets, and orange pulp was examined. The cell mass was increased by 3-fold for K. marxianus and 2-fold for S. cerevisiae in the presence of these substrates, proving their suitability for single-cell protein production without the need for extra nutrients. Cell growth kinetics were also studied by measurements of cell counts at various time intervals at different concentrations of added orange pulp. The protein content of the fermented substrates was increased substantially, indicating potential use of mixed agro-industrial wastes of negligible cost, as protein-enriched livestock feed, achieving at the same time creation of added value and waste minimization.

  20. Assistive technology-based programs to promote communication and leisure activities by three children emerged from a minimal conscious state.

    Science.gov (United States)

    Stasolla, Fabrizio; Caffò, Alessandro O; Damiani, Rita; Perilli, Viviana; Di Leone, Antonia; Albano, Vincenza

    2015-02-01

    This study proposed the use of assistive technology (AT) to promote communication and leisure opportunities by three children with traumatic brain injury (TBI). Furthermore, it assessed the effects of such technology on the indices of positive participation and provided a social validation procedure. Three children emerged from a minimal conscious state and presenting extensive motor disabilities were involved. The intervention program allowed the participants to request and to choice preferred items independently and to perform literacy through a keyboard emulator. A multiple probe design across behaviors with post-intervention check was employed. Outcome measures were correct requests, understandable words, intervals with positive participation, and scores of social validation assessment. Request and choice behaviors and literacy improved significantly during intervention phases. During post-intervention check, all participants consolidated their performance. Moreover, indices of positive participation increased during intervention phases. Scores of social validation assessment showed that the combination of both behaviors was preferable to the same considered separately. AT program showed to be suitable for promoting constructive engagement and literacy behaviors by children with TBI. Future research is needed to generalize this data to a larger sample and to develop new technology for people with different levels of disabilities due to TBI.

  1. Efficient construction of an inverted minimal H1 promoter driven siRNA expression cassette: facilitation of promoter and siRNA sequence exchange.

    Directory of Open Access Journals (Sweden)

    Hoorig Nassanian

    Full Text Available BACKGROUND: RNA interference (RNAi, mediated by small interfering RNA (siRNA, is an effective method used to silence gene expression at the post-transcriptional level. Upon introduction into target cells, siRNAs incorporate into the RNA-induced silencing complex (RISC. The antisense strand of the siRNA duplex then "guides" the RISC to the homologous mRNA, leading to target degradation and gene silencing. In recent years, various vector-based siRNA expression systems have been developed which utilize opposing polymerase III promoters to independently drive expression of the sense and antisense strands of the siRNA duplex from the same template. PRINCIPAL FINDINGS: We show here the use of a ligase chain reaction (LCR to develop a new vector system called pInv-H1 in which a DNA sequence encoding a specific siRNA is placed between two inverted minimal human H1 promoters (approximately 100 bp each. Expression of functional siRNAs from this construct has led to efficient silencing of both reporter and endogenous genes. Furthermore, the inverted H1 promoter-siRNA expression cassette was used to generate a retrovirus vector capable of transducing and silencing expression of the targeted protein by>80% in target cells. CONCLUSIONS: The unique design of this construct allows for the efficient exchange of siRNA sequences by the directional cloning of short oligonucleotides via asymmetric restriction sites. This provides a convenient way to test the functionality of different siRNA sequences. Delivery of the siRNA cassette by retroviral transduction suggests that a single copy of the siRNA expression cassette efficiently knocks down gene expression at the protein level. We note that this vector system can potentially be used to generate a random siRNA library. The flexibility of the ligase chain reaction suggests that additional control elements can easily be introduced into this siRNA expression cassette.

  2. REGULATORY STRATEGIES TO MINIMIZE GENERATION OF REGULATED WASTES FROM CLEANUP, CONTINUED USE OR DECOMMISSIONING OF NUCLEAR FACILITIES CONTAMINATED WITH POLYCHLORINATED BIPHENYLS (PCBS) - 11198

    Energy Technology Data Exchange (ETDEWEB)

    Lowry, N.

    2010-11-05

    Disposal costs for liquid PCB radioactive waste are among the highest of any category of regulated waste. The high cost is driven by the fact that disposal options are extremely limited. Toxic Substances Control Act (TSCA) regulations require most liquids with PCBs at concentration of {ge} 50 parts-per-million to be disposed by incineration or equivalent destructive treatment. Disposal fees can be as high as $200 per gallon. This figure does not include packaging and the cost to transport the waste to the disposal facility, or the waste generator's labor costs for managing the waste prior to shipment. Minimizing the generation of liquid radioactive PCB waste is therefore a significant waste management challenge. PCB spill cleanups often generate large volumes of waste. That is because the removal of PCBs typically requires the liberal use of industrial solvents followed by a thorough rinsing process. In a nuclear facility, the cleanup process may be complicated by the presence of radiation and other occupational hazards. Building design and construction features, e.g., the presence of open grating or trenches, may also complicate cleanup. In addition to the technical challenges associated with spill cleanup, selection of the appropriate regulatory requirements and approach may be challenging. The TSCA regulations include three different sections relating to the cleanup of PCB contamination or spills. EPA has also promulgated a separate guidance policy for fresh PCB spills that is published as Subpart G of 40 CFR 761 although it is not an actual regulation. Applicability is based on the circumstances of each contamination event or situation. Other laws or regulations may also apply. Identification of the allowable regulatory options is important. Effective communication with stakeholders, particularly regulators, is just as important. Depending on the regulatory path that is taken, cleanup may necessitate the generation of large quantities of regulated waste

  3. Incorporation of gypsum waste in ceramic block production: Proposal for a minimal battery of tests to evaluate technical and environmental viability of this recycling process.

    Science.gov (United States)

    Godinho-Castro, Alcione P; Testolin, Renan C; Janke, Leandro; Corrêa, Albertina X R; Radetski, Claudemir M

    2012-01-01

    Civil engineering-related construction and demolition debris is an important source of waste disposed of in municipal solid waste landfills. After clay materials, gypsum waste is the second largest contributor to the residential construction waste stream. As demand for sustainable building practices grows, interest in recovering gypsum waste from construction and demolition debris is increasing, but there is a lack of standardized tests to evaluate the technical and environmental viability of this solid waste recycling process. By recycling gypsum waste, natural deposits of gypsum might be conserved and high amounts of the waste by-product could be reused in the civil construction industry. In this context, this paper investigates a physical property (i.e., resistance to axial compression), the chemical composition and the ecotoxicological potential of ceramic blocks constructed with different proportions of clay, cement and gypsum waste, and assesses the feasibility of using a minimal battery of tests to evaluate the viability of this recycling process. Consideration of the results for the resistance to axial compression tests together with production costs revealed that the best formulation was 35% of plastic clay, 35% of non-plastic clay, 10% of Portland cement and 20% of gypsum waste, which showed a mean resistance of 4.64MPa. Energy dispersive X-ray spectrometry showed calcium and sulfur to be the main elements, while quartz, gypsum, ettringite and nacrite were the main crystalline compounds found in this formulation. Ecotoxicity tests showed that leachate from this formulation is weakly toxic toward daphnids and bacteria (EC(20%)=69.0 and 75.0, respectively), while for algae and fish the leachate samples were not toxic at the EC(50%) level. Overall, these results show that the addition of 20% of gypsum waste to the ceramic blocks could provide a viable substitute for clay in the ceramics industry and the tests applied in this study proved to be a useful tool

  4. Performance management system as a tool for promoting effective waste control : the case of Emfuleni Local Municipality / Sipho J. Ngwenya

    OpenAIRE

    Ngwenya, Sipho Jeffrey

    2014-01-01

    This study aimed at evaluating the degree to which Performance Management System is being executed at Waste Management Unit within the Emfuleni Local Municipality hence the topic “Performance Management System as a tool for promoting effective waste control: The case of the Emfuleni Local Municipality.” The Performance Management System issues a structure for establishing development needs, determining suitable resources, and making the recommendations regarding suitable PMS of which managers...

  5. Guidelines for the disposal of dangerous and toxic wastes so as to minimize or prevent environmental and water pollution

    CSIR Research Space (South Africa)

    Rudd, RT

    1978-01-01

    Full Text Available Modern society is producing ever increasing quantities of dangerous and/or toxic wastes, which require safe and effective disposal if they are not to pose a threat to our water supplies or the environment in general....

  6. Characterization, minimization and disposal of radioactive, hazardous, and mixed wastes during cleanup and rransition of the Tritium Research Laboratory (TRL) at Sandia National Laboratories/California (SNL/CA)

    Energy Technology Data Exchange (ETDEWEB)

    Garcia, T.B.; Gorman, T.P.

    1996-12-01

    This document provides an outline of waste handling practices used during the Sandia National Laboratory/California (SNL/CA), Tritium Research Laboratory (TRL) Cleanup and Transition project. Here we provide background information concerning the history of the TRL and the types of operations that generated the waste. Listed are applicable SNL/CA site-wide and TRL local waste handling related procedures. We describe personnel training practices and outline methods of handling and disposal of compactible and non-compactible low level waste, solidified waste water, hazardous wastes and mixed wastes. Waste minimization, reapplication and recycling practices are discussed. Finally, we provide a description of the process followed to remove the highly contaminated decontamination systems. This document is intended as both a historical record and as a reference to other facilities who may be involved in similar work.

  7. Tribal Waste Management Program

    Science.gov (United States)

    The EPA’s Tribal Waste Management Program encourages environmentally sound waste management practices that promote resource conservation through recycling, recovery, reduction, clean up, and elimination of waste.

  8. Minimizing waste (off-cuts using cutting stock model: The case of one dimensional cutting stock problem in wood working industry

    Directory of Open Access Journals (Sweden)

    Gbemileke A. Ogunranti

    2016-09-01

    Full Text Available Purpose: The main objective of this study is to develop a model for solving the one dimensional cutting stock problem in the wood working industry, and develop a program for its implementation. Design/methodology/approach: This study adopts the pattern oriented approach in the formulation of the cutting stock model. A pattern generation algorithm was developed and coded using Visual basic.NET language. The cutting stock model developed is a Linear Programming (LP Model constrained by numerous feasible patterns. A LP solver was integrated with the pattern generation algorithm program to develop a one - dimensional cutting stock model application named GB Cutting Stock Program. Findings and Originality/value: Applying the model to a real life optimization problem significantly reduces material waste (off-cuts and minimizes the total stock used. The result yielded about 30.7% cost savings for company-I when the total stock materials used is compared with the former cutting plan. Also, to evaluate the efficiency of the application, Case I problem was solved using two top commercial 1D-cutting stock software.  The results show that the GB program performs better when related results were compared. Research limitations/implications: This study round up the linear programming solution for the number of pattern to cut. Practical implications: From Managerial perspective, implementing optimized cutting plans increases productivity by eliminating calculating errors and drastically reducing operator mistakes. Also, financial benefits that can annually amount to millions in cost savings can be achieved through significant material waste reduction. Originality/value: This paper developed a linear programming one dimensional cutting stock model based on a pattern generation algorithm to minimize waste in the wood working industry. To implement the model, the algorithm was coded using VisualBasic.net and linear programming solver called lpsolvedll (dynamic

  9. Implementation of flowsheet change to minimize hydrogen and ammonia generation during chemical processing of high level waste in the Defense Waste Processing Facility

    Energy Technology Data Exchange (ETDEWEB)

    Lambert, Dan P. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Woodham, Wesley H. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Williams, Matthew S. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Newell, J. David [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Luther, Michelle C. [Auburn Univ., AL (United States); Brandenburg, Clayton H. [Univ.of South Carolina, Columbia, SC (United States)

    2016-09-27

    Testing was completed to develop a chemical processing flowsheet for the Defense Waste Processing Facility (DWPF), designed to vitrify and stabilize high level radioactive waste. DWPF processing uses a reducing acid (formic acid) and an oxidizing acid (nitric acid) to rheologically thin the slurry and complete the necessary acid base and reduction reactions (primarily mercury and manganese). Formic acid reduces mercuric oxide to elemental mercury, allowing the mercury to be removed during the boiling phase of processing through steam stripping. In runs with active catalysts, formic acid can decompose to hydrogen and nitrate can be reduced to ammonia, both flammable gases, due to rhodium and ruthenium catalysis. Replacement of formic acid with glycolic acid eliminates the generation of rhodium- and ruthenium-catalyzed hydrogen and ammonia. In addition, mercury reduction is still effective with glycolic acid. Hydrogen, ammonia and mercury are discussed in the body of the report. Ten abbreviated tests were completed to develop the operating window for implementation of the flowsheet and determine the impact of changes in acid stoichiometry and the blend of nitric and glycolic acid as it impacts various processing variables over a wide processing region. Three full-length 4-L lab-scale simulations demonstrated the viability of the flowsheet under planned operating conditions. The flowsheet is planned for implementation in early 2017.

  10. Waste minimization in the remediation of contaminated sites: using the oil belt skimmer technology for the removal of heavy hydrocarbons from groundwater.

    Science.gov (United States)

    De Gisi, Sabino; Notarnicola, Michele

    2016-12-01

    Modern society increasingly requires achieving the goal of remediation and at the same time minimizing the waste to be disposed. Although the pump and treat is a consolidated technology option for the decontamination of groundwater polluted by heavy hydrocarbons, it generates an excessive amount of waste (typically, dangerous). With the intent of reducing such waste, our study is concerned with the verification of the oil belt skimmer technology for the decontamination of a heavy hydrocarbon-polluted groundwater. For this purpose, several tests at laboratory scale and full-scale experimentations with duration greater than 1 year were carried out. The obtained results showed the feasibility of the investigated technology for groundwater decontamination in the cases where the water mobility (of the aquifer) was low and in the presence of oil thicknesses greater than 2 cm. The heavy hydrocarbon recovery capacities were in the range of 33.3-85.5 l/h with the best performances in the cases of supernatant thickness ≥2 cm and pumping of the water table in such a way that the oil acquires a higher mobility in the aquifer. Moreover, the recovery capacity was found to be dependent on the rainfall pattern as well as on the groundwater fluctuation. Compared to the pump-and-treat system, the investigated technology allowed reducing by 98.7 % the amount of waste to be disposed suggesting the use in presence of high thickness of the oils. Finally, in a view of system optimization, treatment trains based on the combination of the oil belt skimmer technology and the pump-and-treat system should be carefully assessed.

  11. Characterization of five evolutionary conserved regions of the human tyrosine hydroxylase (TH) promoter: implications for the engineering of a human TH minimal promoter assembled in a self-inactivating lentiviral vector system.

    Science.gov (United States)

    Romano, Gaetano; Suon, Sokreine; Jin, Hao; Donaldson, Angela E; Iacovitti, Lorraine

    2005-08-01

    A DNA fragment of about 13 kb containing the human tyrosine hydroxylase (TH) promoter was previously isolated from a genomic DNA library and sequenced. The 11 kb from the transcription start of the human TH promoter was successively joined to the green fluorescent protein (GFP) to generate a transgenic mouse model. High levels of GFP expression could be observed in TH-positive cells of the Substantia nigra of embryonic and adult mice. Intriguingly, the sequence of the human TH promoter showed a low degree of homology with the mouse and rat TH promoters. In fact, comparative analysis of the sequences of human, rat, and mouse TH promoters revealed only five small regions of high homology. These five evolutionarily conserved regions were numbered in numeric progression from the 5' end of human TH promoter. In the present study, a panel of minimal human TH promoters was generated to analyze the transcriptional activity and specificity of gene expression conferred by the five conserved regions (CRs). The series of constructs was termed 250 bp and contained the first -194 bp of the human TH promoter immediately upstream of the transcription start, the first 35 bp the human TH messenger RNA leader, plus one or more of the five CRs. All the constructs were assembled in a self-inactivating form of the latest series of lentiviral vector system based on the human immunodeficiency virus type 1 (HIV-1). Lentiviral-mediated gene transfer was highly efficient for the in vitro transduction of human neuronal progenitor cells (hNPCs). Since a subset of hNPCs express TH following in vitro treatment with a mixture of differentiating agents, it was possible to assess specificity of expression for all the minimal human TH promoters. Overall, the successive addition of the five conserved regions produced a greater degree of specificity in induced TH-positive hNPCs, in particular after the addition of CRI (-8,917, -8,876). However, the human TH minimal promoters did not show any

  12. Strategies to enhance waste minimization and energy conservation within organizations: a case study from the UK construction sector.

    Science.gov (United States)

    Jones, Jo; Jackson, Janet; Tudor, Terry; Bates, Margaret

    2012-09-01

    Strategies for enhancing environmental management are a key focus for the government in the UK. Using a manufacturing company from the construction sector as a case study, this paper evaluates selected interventionist techniques, including environmental teams, awareness raising and staff training to improve environmental performance. The study employed a range of methods including questionnaire surveys and audits of energy consumption and generation of waste to examine the outcomes of the selected techniques. The results suggest that initially environmental management was not a focus for either the employees or the company. However, as a result of employing the techniques, the company was able to reduce energy consumption, increase recycling rates and achieve costs savings in excess of £132,000.

  13. Reducing sugar-producing bacteria from guts of Tenebrio molitor Linnaeus (yellow mealworm) for lignocellulosic waste minimization.

    Science.gov (United States)

    Qi, Wei; Chen, Chia-Lung; Wang, Jing-Yuan

    2011-01-01

    The guts of Tenebrio Molitor Linnaeus (yellow mealworm) were used as inocula to isolate reducing sugar-producing bacteria during bioconversion of lignocellulose to reducing sugars in this study. Three carbon sources, i.e., carboxymethyl cellulose (CMC), filter paper (FP), and lignocellulosic waste (LIG), were specifically selected; and two types of culturing media (M1 and M2) were used. After 6 months of sequential cultivation, lignocellulose (i.e., polysaccharides) degradation of enrichments M1-CMC (47.5%), M1-FP (73.3%), M1-LIG (70.4%), M2-CMC (55.7%), M2-FP (73.1%) and M2-LIG (71.7%) was achieved, respectively, with incubation for 48 h. Furthermore, seven bacterial strains were successfully isolated corresponding to most of the major bands detected by denaturing gradient gel electrophoresis analysis. The maximum reducing sugars yield by the combination of Agromyces sp. C42 and Stenotrophomonas sp. A10b was 56.7 mg g·LIG(-1) of 48 h, which is approximate 2-5 times higher than the original enrichments and individual microbial strains. These findings suggest that bioconversion by microorganisms from mealworm guts has great application potential for lignocellulose hydrolysis.

  14. Guidance document available for developers and users in hazardous waste cleanup technologies to minimize occupational hazards to workers

    Energy Technology Data Exchange (ETDEWEB)

    Ruttenberg, R.; Weinstock, D. [National Clearinghouse for Worker Safety and Health Training, Bethesda, MD (United States); Moran, J. [Dept. of Energy, Washington, DC (United States); Dobbin, D. [National Inst. of Environmental Health Sciences, Research Triangle Park, NC (United States)

    1996-12-31

    In evaluating innovative technologies for hazardous waste cleanup, work safety and health issues are rarely considered. In two 1995 technical workshops, co-sponsored by the National Institute of Environmental Health Sciences (NIEHS) and the US Department of Energy (DOE), dozens of experts from government, labor, industry, and academia gathered to write a Guidance Document to be used by the developers and users of innovative cleanup technology. The Guidance Document, which was developed by NIEHS, DOE, and a team of experts, recommends tools to package safety and health information in usable forms--including safety hazard matrices, health hazard matrices, transition check lists, and technology safety data sheets--as well as the need for checklists and contract clauses between remediation companies and responsible parties. Also included in the Guidance Document is a model for phase analysis with a list of the hazards associated with each phase of technological development and implementation. The Guidance Document creates checklists for better identification of hazards that occur during transitions. Emergency response needs are also a focus of the Guidance Document, with minimum standards a key element. Case studies, because they are such powerful tools, are an integral part of the Guidance Document.

  15. Promoting appreciation of the study and practice of medicine: inner workings of a Mini-Med program

    Directory of Open Access Journals (Sweden)

    Lindenthal JJ

    2012-06-01

    Full Text Available Jacob Jay Lindenthal,1 Joel A DeLisa21Department of Psychiatry, Institute for the Public Understanding of Health and Medicine, 2Department of Physical Medicine and Rehabilitation, University of Medicine and Dentistry of New Jersey, New Jersey Medical School, Newark, NJ, USAAbstract: Dissatisfaction with the restrictions of the health care system, diminished reliance on the word of health care professionals, increased costs of medical care, and access to information online have increased consumers' interest in their own health care as well as their thirst for medical literacy. Mini-Med programs run by medical schools offer a more reliable method of learning about disease and disorders than does the indiscriminate surfing of the Internet. This article describes the efforts of the University of Medicine and Dentistry of New Jersey – the largest public university of the health sciences in the nation – to run and maintain such a program. The Mini-Med course provides lay students with insight into what a student undergoes while studying medicine and guides them through complex topics that range from anatomy and basic life support to the latest in stem cell research. It also provides early guidance for potential medical students, addresses patients' concerns, and gives some insight into the levels of comprehension of current medical students.Keywords: Mini-Med program, medical education, consumer education, health literacy

  16. Design, fabrication and testing of an electrolytic membrane cell to minimize the active waste generated during decontamination

    Energy Technology Data Exchange (ETDEWEB)

    Rangarajan, S.; Sumathi, S.; Balaji, V.; Puspalata, R. [BARC Facilities, Water and Steam Chemistry Div., Kalpakkam, Tamilnadu (India)

    2010-07-01

    Decontamination of the Primary Heat Transport system of the Nuclear Power Plants has become a regular exercise, carried out once in three or four years, to reduce the background radioactivity levels around the circuit and hence to control the associated man-rem budgeting. In a typical dilute chemical decontamination campaign, either a reducing or an oxidizing formulation (which depends on the nature of the oxide) containing a mixture of complexing acids are used to dissolve the surface oxides and the impregnated radioactive metal ions which are subsequently removed using ion-exchanger columns. However, this procedure not only requires many ion-exchanger columns, but also generates a large volume of active waste. By coupling suitably the ion exchange resins and electrolytic membrane cell one can effectively remove metal ions from the decontaminant formulation. This will also reduce the waste liquid volume. Apart from this, by optimizing the current-potential characteristics of the cell, one can selectively deposit / remove a particular metal ion from the other metal ions. In this paper, the design, fabrication and testing of an Electrolytic Membrane Cell containing three compartments viz., cathodic, anodic and a central feed compartment, each separated from the other by a cation-permeable nafion membrane (Na form) with Titanium cathode and a Platinum-coated Titanium anode are described in detail. Experiments were carried out with simulated decontamination solutions containing either magnetite (Fe{sub 3}O{sub 4}) or cobalt oxide (Co{sub 3}O{sub 4}) or both as a mixture in ethylene diamine tetra-acetic acid/ Nitrilo triacetic acid, ascorbic acid and citric acid (EAC / NAC) formulations, for effective removal of Co from a large quantity of Fe. The percentage of metal ion transport, pH and conductivity in the feed, catholyte and anolyte solutions were monitored as a function of electrical charge passed through the electrochemical cell. The results showed that the

  17. Waste minimization opportunities at the U.S. Uranium Mill Tailings Remedial Action (UMTRA) Project, Rifle, Colorado, site

    Energy Technology Data Exchange (ETDEWEB)

    Hartmann, G.L. [Geraghty and Miller, Albuquerque, NM (United States); Arp, S. [Dept. of Energy, Albuquerque, NM (United States); Hempill, H. [Morrison Knudsen-Environmental Services, San Francisco, CA (United States)

    1993-12-31

    At two uranium mill sites in Rifle, Colorado, the US Department of Energy (DOE) Uranium Mill Tailings Remedial Action (UMTRA) Project is removing uranium mill tailings and contaminated subgrade soils. This remediation activity will result in the production of groundwater contaminated with uranium, heavy metals, ammonia, sulfates, and total dissolved solids (TDS). The initial remediation plan called for a wastewater treatment plant for removal of the uranium, heavy metals, and ammonia, with disposal of the treated water, which still includes the sulfates and TDSS, to the Colorado River. The National Pollutant Discharge Elimination (NPDES) permit issued by the Colorado Department of Health for the two Rifle sites contained more restrictive discharge limits than originally anticipated. During the detailed review of alternate treatment systems to meet these more restrictive limits, the proposed construction procedures were reviewed emphasizing the methods to minimize groundwater production to reduce the size of the water treatment facility, or to eliminate it entirely. It was determined that with changes to the excavation procedures and use of the contaminated groundwater for use in dust suppression at the disposal site, discharge to the river could be eliminated completely.

  18. Promoting appreciation of the study and practice of medicine: inner workings of a Mini-Med program.

    Science.gov (United States)

    Lindenthal, Jacob Jay; Delisa, Joel A

    2012-01-01

    Dissatisfaction with the restrictions of the health care system, diminished reliance on the word of health care professionals, increased costs of medical care, and access to information online have increased consumers' interest in their own health care as well as their thirst for medical literacy. Mini-Med programs run by medical schools offer a more reliable method of learning about disease and disorders than does the indiscriminate surfing of the Internet. This article describes the efforts of the University of Medicine and Dentistry of New Jersey - the largest public university of the health sciences in the nation - to run and maintain such a program. The Mini-Med course provides lay students with insight into what a student undergoes while studying medicine and guides them through complex topics that range from anatomy and basic life support to the latest in stem cell research. It also provides early guidance for potential medical students, addresses patients' concerns, and gives some insight into the levels of comprehension of current medical students.

  19. Working towards a zero waste environment in Taiwan.

    Science.gov (United States)

    Young, Chea-Yuan; Ni, Shih-Piao; Fan, Kuo-Shuh

    2010-03-01

    It is essential to the achievement of zero waste that emphasis is concentrated on front-end preventions rather than end-of-pipe (EOP) treatment. Zero waste is primarily based on cleaner production, waste management, the reduction of unnecessary consumption and the effective utilization of waste materials. The aim of this study was to briefly review the tasks undertaken and future plans for achieving zero waste in Taiwan. Waste prevention, source reduction, waste to product, waste to energy, EOP treatment, and adequate disposal are the sequential principal procedures to achieve the goal of zero waste. Six strategies have been adopted to implement the zero waste policy in Taiwan. These are regulatory amendments, consumption education, financial incentives, technical support, public awareness, and tracking and reporting. Stepwise targets have been set for 2005, 2007, 2011, and 2020 for both the municipal solid waste (MSW) and industrial waste to reach the goal of zero waste. The eventual aim is to achieve 70% MSW minimization and 85% industrial waste minimization by 2020. Although tools and measures have been established, some key programmes have higher priority. These include the establishment of a waste recycling programme, promotion of cleaner production, a green procurement programme, and promotion of public awareness. Since the implementation of the zero waste policy started in 2003, the volume of MSW for landfill and incineration has declined dramatically. The recycling and/or minimization of MSW quantity in 2007 was 37%, which is much higher than the goal of 25%. Industrial waste reached almost 76% minimization by the end of 2006, which is 1 year before the target year.

  20. Plant Growth Promotion Activity of Keratinolytic Fungi Growing on a Recalcitrant Waste Known as “Hair Waste”

    Directory of Open Access Journals (Sweden)

    Ivana A. Cavello

    2015-01-01

    Full Text Available Purpureocillium lilacinum (Thom Samsom is one of the most studied fungi in the control of plant parasitic nematodes. However, there is not specific information on its ability to inhibit some pathogenic bacteria, fungi, or yeast. This work reports the production of several antifungal hydrolytic enzymes by a strain of P. lilacinum when it is grown in a medium containing hair waste. The growth of several plant-pathogenic fungi, Alternaria alternata, Aspergillus niger, and Fusarium culmorum, was considerably affected by the presence of P. lilacinum’s supernatant. Besides antifungal activity, P. lilacinum demonstrates the capability to produce indoleacetic acid and ammonia during time cultivation on hair waste medium. Plant growth-promoting activity by cell-free supernatant was evidenced through the increase of the percentage of tomato seed germination from 71 to 85% after 48 hours. A 21-day plant growth assay using tomato plants indicates that crude supernatant promotes the growth of the plants similar to a reference fertilizer (p>0.05. These results suggest that both strain and the supernatant may have potential to be considered as a potent biocontrol agent with multiple plant growth-promoting properties. To our knowledge, this is the first report on the antifungal, IAA production and tomato growth enhancing compounds produced by P. lilacinum LPSC #876.

  1. Development of the consumption behavior that promotes sustainable society: Focusing on recycling of small waste home appliances

    Science.gov (United States)

    Ichinose, Takae

    2015-04-01

    Hiroshima University High School (HUHS) became the first UNESCO Associated School in Japan in 1953, and since then it has practiced ESD in various educational activities in all ranges of education. As a teacher of home economics, I have focused on consumer affairs and encouraged my students to consider what each of them can do as an individual consumer in order to create a sustainable society. In Japan, several acts related to consumer affairs have been enforced in recent years. "Act on Promotion of Consumer Education" was enforced in December 2012, and construction of the "Consumer Citizen Society" was proposed. It places emphasis not only on environmental concerns but also on the initiative of consumers and its influence on social and economic trends. In addition, "Act on Promotion of Recycling of Small Waste Electrical and Electronic Equipment" was enforced in April, 2013. It aims at protecting living environment and healthy development of the national economy by appropriate treatment of waste materials and effective use of resources. For my lessons on "food, clothing and shelter in relation to consumption behavior and environmental problems", I took up "the recycling of small waste home appliances" as the teaching materials to raise awareness on resources recycling. The purpose of the lessons is three-fold: (1) to make students aware of environmental load; (2) to deepen the understanding of the influence which excessive consumption has on developing countries; (3) to encourage the students to think positively toward the solution of the problems. I am currently practicing the lessons, and I have shown below the summary of the instruction. Lesson 1: Give a quiz based on the database on environmental label from Ministry of the Environment website. Then show a film on whereabouts of the hi-tech industrial waste (e-waste). After the film, show some everyday products for which mineral resources are used in order to impress the idea of "urban mine". Lesson 2: Show a

  2. Central thalamic deep brain stimulation to promote recovery from chronic posttraumatic minimally conscious state: challenges and opportunities.

    Science.gov (United States)

    Giacino, Joseph; Fins, Joseph J; Machado, Andre; Schiff, Nicholas D

    2012-07-01

    Central thalamic deep brain stimulation (CT-DBS) may have therapeutic potential to improve behavioral functioning in patients with severe traumatic brain injury (TBI), but its use remains experimental. Current research suggests that the central thalamus plays a critical role in modulating arousal during tasks requiring sustained attention, working memory, and motor function. The aim of the current article is to review the methodology used in the CT-DBS protocol developed by our group, outline the challenges we encountered and offer suggestions for future DBS trials in this population. RATIONAL FOR CT-DBS IN TBI:  CT-DBS may therefore be able to stimulate these functions by eliciting action potentials that excite thalamocortical and thalamostriatal pathways. Because patients in chronic minimally conscious state (MCS) have a very low probability of regaining functional independence, yet often have significant sparing of cortical connectivity, they may represent a particularly appropriate target group for CT-DBS. PIlOT STUDY RESULTS:  We have conducted a series of single-subject studies of CT-DBS in patients with chronic posttraumatic MCS, with 24-month follow-up. Outcomes were measured using the Coma Recovery Scale-Revised as well as a battery of secondary outcome measures to capture more granular changes. Findings from our index case suggest that CT-DBS can significantly increase functional communication, motor performance, feeding, and object naming in the DBS on state, with performance in some domains remaining above baseline even after DBS was turned off. The use of CT-DBS in patients in MCS, however, presents challenges at almost every step, including during surgical planning, outcome measurement, and postoperative care. Additionally, given the difficulties of obtaining informed consent from patients in MCS and the experimental nature of the treatment, a robust, scientifically rooted ethical framework is resented for pursuing this line of work. © 2012

  3. Cradle-to-cradle stewardship of drugs for minimizing their environmental disposition while promoting human health. I. Rationale for and avenues toward a green pharmacy.

    Science.gov (United States)

    Daughton, Christian G

    2003-05-01

    Since the 1980s, the occurrence of pharmaceuticals and personal care products (PPCPs) as trace environmental pollutants, originating primarily from consumer use and actions rather than manufacturer effluents, continues to become more firmly established. Although PPCPs typically have been identified in surface and ground waters, some are also undoubtedly associated with solid phases such as suspended particulates, sediments, and sewage sludges, despite their relatively high affinity for water. Often amenable to degradation, their continual introduction to waste-receiving waters results from their widespread, continuous, combined use by individuals and domestic animals, giving PPCPs a "pseudo-persistence" in the environment. Little is known about the environmental or human health hazards that might be posed by chronic, subtherapeutic levels of these bioactive substances or their transformation products. The continually growing, worldwide importance of freshwater resources, however, underscores the need for ensuring that any aggregate or cumulative impacts on (or from) water supplies are minimized. Despite the paucity of effects data from long-term, simultaneous exposure at low doses to multiple xenobiotics (particularly non-target-organism exposure to PPCPs), a wide range of proactive actions could be implemented to reduce or minimize the introduction of PPCPs to the environment. Most of these actions fall under what could be envisioned as a holistic stewardship program--overseen by the health care industry and consumers alike. Significantly, such a stewardship program would benefit not just the environment; additional, collateral benefits could automatically accrue, including reducing consumers' medication expenses and improving patient health and consumer safety. In this article, the first of a two-part mini-monograph describing the "green pharmacy," I focus initially on the background behind the imperative for an ecologically oriented stewardship program for PPCPs

  4. MINIMASI RESIKO DALAM SISTEM PENGELOLAAN LIMBAH MEDIS DI KOTA BANDUNG, INDONESIA DENGAN PENDEKATAN LINEAR PROGRAMMING (Risk Minimization for Medical Waste Management System in Bandung City, Indonesia: A Linear Programming Approach

    Directory of Open Access Journals (Sweden)

    Mochammad Chaerul

    2013-07-01

    Full Text Available ABSTRAK Berbagai macam pelayanan perawatan kesehatan yang disediakan oleh rumah sakit akan berpotensi menghasilkan limbah medis. Walaupun sebagian besar limbah rumah sakit dapat dikelompokkan sebagai limbah yang tidak berbahaya yang memiliki sifat yang sama dengan sampah rumah tangga dan dapat dibuang ke tempat penimbunan sampah, sebagian kecil dari limbah medis harus dikelola dengan tepat untuk meminimasi resiko terhadap kesehatan masyarakat. Model pengelolaan limbah medis yang dikembangkan ditujukan untuk meminimasi resiko terhadap fasilitas umum dan komersial seperti fasilitas ibadah, bank, perkantoran, restoran, hotel, stasiun pengisian bahan bakar, fasilitas pendidikan, mall dan pusat perbelanjaan, taman dan pusat olahraga/kebugaran, akibat pengangkutan limbah medis dan abu hasil pengolahannya. Tingkat resiko dari setiap fasilitas di atas ditentukan menggunakan metode Analytical Hierarchy Process (AHP. Permasalahan diselesaikan dengan mengaplikasikan linear programming menggunakan software optimimasi LINGO®. Output model berupa optimasi alokasi limbah medis dari setiap rumah sakit ke fasilitas pengolahan dan alokasi abu dari fasilitas pengolahan ke tempat penimbunan akhir. Hasil model memperlihatkan bahwa rute terpendek tidak menghasilkan total resiko terkecil karena dipengaruhi oleh jumlah dan tingkat resiko dari setiap fasilitas yang dilalui oleh kemdaraan pengangkut limbah medis dan abu. Perbedaan fasilitas yang berada di sekitar pengolahan limbah medis juga akan menghasilkan total resiko yang berbeda. ABSTRACT A broad range of healthcare services provided by hospital may generate medical waste. Although a large percentage of hospital waste is classified as general waste, which has similar nature as that of municipal solid waste and, therefore, could be disposed in municipal landfill, a small portion of medical waste has to be managed in a proper manner to minimize risk to public health. A medical waste management model is proposed in

  5. Minimal concentrations of retinoic acid induce stimulation by retinoic acid 8 and promote entry into meiosis in isolated pregonadal and gonadal mouse primordial germ cells.

    Science.gov (United States)

    Tedesco, Marianna; Desimio, Maria Giovanna; Klinger, Francesca Gioia; De Felici, Massimo; Farini, Donatella

    2013-06-01

    In the present study, we demonstrate that minimal concentrations (≤ 1 nM) of retinoic acid (RA), equivalent to the quantity contaminating serum-containing culture medium, are sufficient to promote meiotic entry and progression through meiotic prophase I (MPI) stages in isolated 12.5-days postcoitum (dpc) XX and XY mouse primordial germ cells (PGCs) in culture. Similarly, we found that the same low RA concentration up-regulated or induced stimulation by retinoic acid 8 (Stra8) in such cells, both at mRNA and protein level. In preleptotene/leptotene germ cells, STRA8 was localized in nuclear dots that disappeared at later MPI stages. In addition to Stra8, other meiotic genes such as Dmc1 and Rec8 appeared stimulated by RA directly in PGCs with similar concentration-dependent trends. Finally, we found that RA induced Stra8, Sycp3, Dmc1, and Rec8 transcripts, promoting meiotic entry in culture also in pregonadal 10.5-dpc PGCs of both sexes. When cultured isolated from somatic cells, such PGCs, however, were unable to progress through MPI stages, while after entering meiosis, they progressed through MPI when cultured within aorta/gonad/mesonephros tissues. We conclude that besides RA, germ cell intrinsic factors and other exogenous signals from the surrounding somatic cells are probably necessary for meiotic entry and progression in mouse PGCs.

  6. Regional planning for minimization, recycling and recovery of wastes in Asturias. Plan regional de reduccion, reciclaje y recuperacion de residuos en Asturias

    Energy Technology Data Exchange (ETDEWEB)

    1994-01-01

    Asturias (Spain) produces 350.000 ton of urban solid wastes per year. 97 per cent of them are treated and their leachates are delivered on a special plant where are depurated avoiding to pollute underground waters. In 1993 there were energetic uses of these wastes obtaining 25 millions Kw of electric energy. This paper presents the Plan of Government of Asturias to collect the urban solid waste and its treatment. (Author)

  7. Innovative landfill bioreactor systems for municipal solid waste treatment in East Africa aimed at optimal energy recovery and minimal greenhouse gas emissions

    NARCIS (Netherlands)

    Salukele, F.M.

    2013-01-01

    Landfilling is currently the dominant disposal method for municipal solid waste (MSW) in developing countries. Approximately 50% of the MSW generated in East Africa is disposed in landfills. Low costs and availability of land have made landfilling the most common waste management option in East

  8. Waste materials derived bio-effectors used as growth promoters for strawberry plants. An agronomic and metabolomic study

    Science.gov (United States)

    Vasileva, Brankica; Chami, Ziad Al; De Pascali, Sandra; Cavoski, Ivana; Fanizzi, Francesco Paolo

    2015-04-01

    Recently, a novel concept of bio-effectors has emerged to describe a group of products that are able to improve plant performance more than fertilizers. In this study, three different agro-industrial residues, i.e. brewers' spent grain (BSG), fennel processing residues (FPR) and lemon processing residues (LPR) were chosen as potential bio-effectors. A greenhouse soilless pot experiment was conducted on strawberry plants (Fragaria x ananassa var. Festival) in order to study the effect of BSG, FPR and LPR water extracts, at different concentrations, on plant growth and fruit quality. Their effect was compared with humic-like substances as a positive/reference control (Ctrl+) and with Hoagland solution as a negative control (Ctrl-). Agronomic parameters and the nutrient uptake were measured on shoots, roots and fruits. Metabolomic profiling tests were carried out on leaves, roots and fruit juices through the NMR technique. Plants treated with the FPR extract showed better vegetative growth, while plants treated with the BSG extract gave higher yield and better fruit size. Metabolomic profiling showed that fruits and roots of plants treated with FPR and LPR extracts had higher concentrations of sucrose, malate and acetate, while BSG treated plants had higher concentrations of citrate and β-glucose. In conclusion, according to the results achieved, the bio-effectors used in this study promote plant growth and fruit quality regardless of their nutritional content. Keywords: bio-effectors, agro-industrial waste, nuclear magnetic resonance (NMR), strawberry, growth promotion, fruit quality.

  9. Novel multifunctional plant growth-promoting bacteria in co-compost of palm oil industry waste.

    Science.gov (United States)

    Chin, Clament Fui Seung; Furuya, Yoshihide; Zainudin, Mohd Huzairi Mohd; Ramli, Norhayati; Hassan, Mohd Ali; Tashiro, Yukihiro; Sakai, Kenji

    2017-11-01

    Previously, a unique co-compost produced by composting empty fruit bunch with anaerobic sludge from palm oil mill effluent, which contributed to establishing a zero-emission industry in Malaysia. Little was known about the bacterial functions during the composting process and fertilization capacity of this co-compost. We isolated 100 strains from the co-compost on 7 types of enumeration media and screened 25 strains using in vitro tests for 12 traits, grouping them according to three functions: plant growth promoting (fixation of nitrogen; solubilization of phosphorus, potassium, and silicate; production of 3-indoleacetic acid, ammonia, and siderophore), biocontrolling (production of chitinase and anti-Ganoderma activity), and composting (degradation of lignin, xylan, and cellulose). Using 16S rRNA gene sequence analysis, 25 strains with strong or multi-functional traits were found belong to the genera Bacillus, Paenibacillus, Citrobacter, Enterobacter, and Kosakonia. Furthermore, several strains of Citrobacter sedlakii exhibited a plant growth-stimulation in vivo komatsuna plant cultivation test. In addition, we isolated several multifunctional strains; Bacillus tequilensis CE4 (biocontrolling and composting), Enterobacter cloacae subsp. dissolvens B3 (plant growth promoting and biocontrolling), and C. sedlakii CESi7 (plant growth promoting and composting). Some bacteria in the co-compost play significant roles during the composting process and plant cultivation after fertilization, and some multifunctional strains have potential for use in accelerating the biodegradation of lignocellulosic biomass, protecting against Ganoderma boninense infection, and increasing the yield of palm oil. Copyright © 2017 The Society for Biotechnology, Japan. Published by Elsevier B.V. All rights reserved.

  10. Examination of Uranium(VI) Leaching During Ligand Promoted Dissolution of Waste Tank Sludge Surrogates

    Energy Technology Data Exchange (ETDEWEB)

    Powell, Brian; Powell, Brian A.; Rao, Linfeng; Nash, Kenneth. L.

    2008-06-10

    The dissolution of synthetic boehmite (?-AlOOH) by 1-hydroxyethane-1,1-diphosphonic acid (HEDPA) was examined in a series of batch adsorption/dissolution experiments. Additionally, the leaching behavior of {sup 233}U(VI) from boehmite was examined as a function of pH and HEDPA concentration. The results are discussed in terms of sludge washing procedures that may be utilized during underground tank waste remediation. In the pH range 4 to 10, complexation of Al(III) by HEDPA significantly enhanced dissolution of boehmite. This phenomenon was especially pronounced in the neutral pH region where the solubility of aluminum, in the absence of complexants, is limited by the formation of sparsely soluble aluminum hydroxides. At pH higher than 10, dissolution of synthetic boehmite was inhibited by HEDPA, likely due to sorption of Al(III):HEDPA complexes. Addition of HEDPA to equilibrated U(VI)-synthetic boehmite suspensions yielded an increase in the aqueous phase uranium concentration. Partitioning of uranium between the solid and aqueous phase is described in terms of U(VI):HEDPA speciation and dissolution of the boehmite solid phase.

  11. Modeling routes of chronic wasting disease transmission: Environmental prion persistence promotes deer population decline and extinction

    Science.gov (United States)

    Almberg, Emily S.; Cross, Paul C.; Johnson, Christopher J.; Heisey, Dennis M.; Richards, Bryan J.

    2011-01-01

    Chronic wasting disease (CWD) is a fatal disease of deer, elk, and moose transmitted through direct, animal-to-animal contact, and indirectly, via environmental contamination. Considerable attention has been paid to modeling direct transmission, but despite the fact that CWD prions can remain infectious in the environment for years, relatively little information exists about the potential effects of indirect transmission on CWD dynamics. In the present study, we use simulation models to demonstrate how indirect transmission and the duration of environmental prion persistence may affect epidemics of CWD and populations of North American deer. Existing data from Colorado, Wyoming, and Wisconsin's CWD epidemics were used to define plausible short-term outcomes and associated parameter spaces. Resulting long-term outcomes range from relatively low disease prevalence and limited host-population decline to host-population collapse and extinction. Our models suggest that disease prevalence and the severity of population decline is driven by the duration that prions remain infectious in the environment. Despite relatively low epidemic growth rates, the basic reproductive number, R0, may be much larger than expected under the direct-transmission paradigm because the infectious period can vastly exceed the host's life span. High prion persistence is expected to lead to an increasing environmental pool of prions during the early phases (i.e. approximately during the first 50 years) of the epidemic. As a consequence, over this period of time, disease dynamics will become more heavily influenced by indirect transmission, which may explain some of the observed regional differences in age and sex-specific disease patterns. This suggests management interventions, such as culling or vaccination, will become increasingly less effective as CWD epidemics progress.

  12. Bio-effectors from waste materials as growth promoters, an agronomic and metabolomic study

    Science.gov (United States)

    Alwanney, Deaa; Chami, Ziad Al; Angelica De Pascali, Sandra; Cavoski, Ivana; Fanizzi, Francesco Paolo

    2014-05-01

    Nowadays, improving plant performance by providing growth promoters is a main concern of the organic agriculture. As a consequence of increased food demands, more efficient and alternatives of the current plant nutrition strategies are becoming urgent. Recently, a novel concept "bio-effectors" raised on to describe a group of products that are able to improve plant performance and do not belong to fertilizers or pesticides. Agro-Food processing residues are promising materials as bio-effector. Three plant-derived materials: brewers' spent grain (BSG), fennel processing residues (FPR) and lemon processing residues (LPR) were chosen as bio-effector candidates. Plant-derived materials were characterized in term of total macro and micronutrients content. Green extraction methodology and solvent choice (aqueous; ethanol; and aqueous: ethanol mixture 1:1) was based on the extraction yield as main factor. Optimum extracts, to be used on the tomato test plant, were determined using phytotoxicity test (seed germination test) as main constraint. Thereafter, selected extracts were characterized and secondary metabolites profiling were detected by NMR technique. Selected extracts were applied on tomato in a growth chamber at different doses in comparison to humic-like substances as positive control (Ctrl+) and to a Hoagland solution as negative control (Ctrl-). At the end of the experiment, agronomical parameters were determined and NMR-metabolomic profiling were conducted on tomato seedlings. Results are summarized as follow: (i) raw showed an interesting content, either at nutritional or biological level; (ii) aqueous extraction resulted higher yield than other used solvent; (iii) at high extraction ratio (1:25 for BSG; 1:100 for FPR; and 1:200 for LPR) aqueous extracts were not phytotoxic on the tomato test plant; (iv) all aqueous extract are differently rich in nutrients, aminoacids, sugars and low molecular weight molecules; (v) all extract exhibited a growth promotion at

  13. Public participation as a mechanism for promoting sustainable waste management service delivery in Sedibeng District Municipality / Nompazamo Alma Ludidi

    OpenAIRE

    Ludidi, Nompazamo Alma

    2013-01-01

    The purpose of this research is to determine the extent of public participation in waste management, willingness of the community to assist the municipality in waste management and how the officials involve the community as partners in waste management. Waste management has become a big environmental challenge in Sedibeng District Municipality due to rural- urban drift leading to population increase in the region. In cities and towns where there is population increase there is excessive gener...

  14. Managing Waste Throughout Lean-Green Perspective

    Directory of Open Access Journals (Sweden)

    Lamyaa Mohammed Dawood

    2017-11-01

    Full Text Available Managing waste has been known as a crucial need as it may reduce resource consumption, rigid regulations regarded to the environment and occupational health and safety. Lean and green management are two approaches of management that validate waste. Since performance measures are crucial to improve waste management as its  goals of  to promote the performance of organizations .In this research four primary KPIs have been employed that are significant to lean-green management; operational, environmental, economic and social performance factors, subdivided further into sixteen as (Value stream mapping, life cycle assessment,---etc. Also in this research   determination and ranking of these performance measures and their influence on waste minimization is conducted. Interpretive Structural Modeling (ISM methodology is applied to the classification of Key Performance Indicators (KPIs according to the priority of their importance and the correlation between them and their impact to waste minimization. Cronbach’s Alpha coefficient is employed  to assess the reliability of performance measures to minimize waste, and increase customer  satisfaction.  Results showed that Al-Kufa Cement plant has bad overall performance toward lean green waste management perspective. The highest individual score is for operational performance (6.6 rated as medium. But  the lowest individual score is for economic performance [very bad (2.0].   

  15. Regulatory Promotion of Waste Wood Reused as an Energy Source and the Environmental Concerns about Ash Residue in the Industrial Sector of Taiwan

    Directory of Open Access Journals (Sweden)

    Wen-Tien Tsai

    2012-11-01

    Full Text Available The objective of this paper was to provide a preliminary analysis of the utilization of energy derived from waste wood in Taiwan, a highly industrialized country with a high dependence (over 99% on imported energy. The discussion focuses on the status of waste wood generation and its management over the past decade. Findings show that the quantities of biomass waste collected for reuse purposes in the industrial sectors of Taiwan has exhibited an increasing trend, from about 4000 tons in 2001 to over 52,000 tons in 2010. Although waste wood can be reused as a fuel and raw material for a variety of applications based on regulatory promotion, the most commonly used end use is to directly utilize it as an auxiliary fuel in industrial utilities (e.g., boilers, heaters and furnaces for the purpose of co-firing with coal/fuel oil. The most progressive measure for promoting biomass-to-power is to introduce the feed-in tariff (FIT mechanism according to the Renewable Energy Development Act passed in June 2009. The financial support for biomass power generation has been increasing over the years from 0.070 US$/kWh in 2010 to 0.094 US$/kWh in 2012. On the other hand, the environmental regulations in Taiwan regarding the hazard identification of wood-combusted ash (especially in filter fly-ash and its options for disposal and utilization are further discussed in the paper, suggesting that waste wood impregnated with chromated copper arsenate (CCA and other copper-based preservatives should be excluded from the wood-to-energy system. Finally, some recommendations for promoting wood-to-energy in the near future of Taiwan are addressed.

  16. Up-cycling waste glass to minimal water adsorption/absorption lightweight aggregate by rapid low temperature sintering: optimization by dual process-mixture response surface methodology.

    Science.gov (United States)

    Velis, Costas A; Franco-Salinas, Claudia; O'Sullivan, Catherine; Najorka, Jens; Boccaccini, Aldo R; Cheeseman, Christopher R

    2014-07-01

    Mixed color waste glass extracted from municipal solid waste is either not recycled, in which case it is an environmental and financial liability, or it is used in relatively low value applications such as normal weight aggregate. Here, we report on converting it into a novel glass-ceramic lightweight aggregate (LWA), potentially suitable for high added value applications in structural concrete (upcycling). The artificial LWA particles were formed by rapidly sintering (glass powder with clay mixes using sodium silicate as binder and borate salt as flux. Composition and processing were optimized using response surface methodology (RSM) modeling, and specifically (i) a combined process-mixture dual RSM, and (ii) multiobjective optimization functions. The optimization considered raw materials and energy costs. Mineralogical and physical transformations occur during sintering and a cellular vesicular glass-ceramic composite microstructure is formed, with strong correlations existing between bloating/shrinkage during sintering, density and water adsorption/absorption. The diametrical expansion could be effectively modeled via the RSM and controlled to meet a wide range of specifications; here we optimized for LWA structural concrete. The optimally designed LWA is sintered in comparatively low temperatures (825-835 °C), thus potentially saving costs and lowering emissions; it had exceptionally low water adsorption/absorption (6.1-7.2% w/wd; optimization target: 1.5-7.5% w/wd); while remaining substantially lightweight (density: 1.24-1.28 g.cm(-3); target: 0.9-1.3 g.cm(-3)). This is a considerable advancement for designing effective environmentally friendly lightweight concrete constructions, and boosting resource efficiency of waste glass flows.

  17. The experimental investigation on the performance of a low temperature waste heat-driven multi-bed desiccant dehumidifier (MBDD) and minimization of entropy generation

    KAUST Repository

    Myat, Aung

    2012-06-01

    We present the experimental investigation on the performance of multi-bed desiccant dehumidification system (MBDD) using a thermodynamic framework with an entropy generation analysis. The cyclic steady state performance of adsorption-desorption processes at the assorted heat source temperatures, and typical ambient humidity conditions was carried out. MBDD unit uses type-RD silica gel pore surface area with of 720 m 2/g. It has a nominal diameter range of 0.4 to 0. 7 mm. The key advantages of MBDD are: (i) it has no moving parts rendering less maintenance, (ii) energy-efficient means of dehumidification by adsorption process with low temperature heat source as compared to the conventional methods, (iii) although it is a pecked bed desiccant, a laminar chamber is employed by arranging the V-shaped configuration of heat exchangers and (iv) it is environmental friendly with the low-carbon footprint. Entropy generation analysis was performed at the assorted heat source temperatures to investigate the performance of MBDD. By conducting the entropy minimization, it is now able to locate the optimal operating conditions of the system while the specific entropy generation is found to be minimal. This analysis shows that the minimization of entropy generation in the dehumidification cycle leads to the maximization of COP in the MBDD and thus, higher delivery of useful effects at the same input resources. © 2011 Elsevier Ltd. All rights reserved.

  18. Municipal Solid Waste Resources

    Energy Technology Data Exchange (ETDEWEB)

    None

    2016-06-01

    Municipal solid waste (MSW) is a source of biomass material that can be utilized for bioenergy production with minimal additional inputs. MSW resources include mixed commercial and residential garbage such as yard trimmings, paper and paperboard, plastics, rubber, leather, textiles, and food wastes. Waste resources such as landfill gas, mill residues, and waste grease are already being utilized for cost-effective renewable energy generation. MSW for bioenergy also represents an opportunity to divert greater volumes of residential and commercial waste from landfills.

  19. Replacement of chemical oxygen demand (COD) with total organic carbon (TOC) for monitoring wastewater treatment performance to minimize disposal of toxic analytical waste.

    Science.gov (United States)

    Dubber, Donata; Gray, Nicholas F

    2010-10-01

    Chemical oxygen demand (COD) is widely used for wastewater monitoring, design, modeling and plant operational analysis. However this method results in the production of hazardous wastes including mercury and hexavalent chromium. The study examined the replacement of COD with total organic carbon (TOC) for general performance monitoring by comparing their relationship with influent and effluent samples from 11 wastewater treatment plants. Biochemical oxygen demand (BOD5) was also included in the comparison as a control. The results show significant linear relationships between TOC, COD and BOD5 in settled (influent) domestic and municipal wastewaters, but only between COD and TOC in treated effluents. The study concludes that TOC can be reliably used for the generic replacement of both COD (COD=49.2+3.00*TOC) and BOD5 (BOD5=23.7+1.68*TOC) in influent wastewaters but only for COD (COD=7.25+2.99*TOC) in final effluents.

  20. A step by step selection method for the location and the size of a waste-to-energy facility targeting the maximum output energy and minimization of gate fee.

    Science.gov (United States)

    Kyriakis, Efstathios; Psomopoulos, Constantinos; Kokkotis, Panagiotis; Bourtsalas, Athanasios; Themelis, Nikolaos

    2017-06-23

    This study attempts the development of an algorithm in order to present a step by step selection method for the location and the size of a waste-to-energy facility targeting the maximum output energy, also considering the basic obstacle which is in many cases, the gate fee. Various parameters identified and evaluated in order to formulate the proposed decision making method in the form of an algorithm. The principle simulation input is the amount of municipal solid wastes (MSW) available for incineration and along with its net calorific value are the most important factors for the feasibility of the plant. Moreover, the research is focused both on the parameters that could increase the energy production and those that affect the R1 energy efficiency factor. Estimation of the final gate fee is achieved through the economic analysis of the entire project by investigating both expenses and revenues which are expected according to the selected site and outputs of the facility. In this point, a number of commonly revenue methods were included in the algorithm. The developed algorithm has been validated using three case studies in Greece-Athens, Thessaloniki, and Central Greece, where the cities of Larisa and Volos have been selected for the application of the proposed decision making tool. These case studies were selected based on a previous publication made by two of the authors, in which these areas where examined. Results reveal that the development of a «solid» methodological approach in selecting the site and the size of waste-to-energy (WtE) facility can be feasible. However, the maximization of the energy efficiency factor R1 requires high utilization factors while the minimization of the final gate fee requires high R1 and high metals recovery from the bottom ash as well as economic exploitation of recovered raw materials if any.

  1. Taxonomic minimalism.

    Science.gov (United States)

    Beattle, A J; Oliver, I

    1994-12-01

    Biological surveys are in increasing demand while taxonomic resources continue to decline. How much formal taxonomy is required to get the job done? The answer depends on the kind of job but it is possible that taxonomic minimalism, especially (1) the use of higher taxonomic ranks, (2) the use of morphospecies rather than species (as identified by Latin binomials), and (3) the involvement of taxonomic specialists only for training and verification, may offer advantages for biodiversity assessment, environmental monitoring and ecological research. As such, formal taxonomy remains central to the process of biological inventory and survey but resources may be allocated more efficiently. For example, if formal Identification is not required, resources may be concentrated on replication and increasing sample sizes. Taxonomic minimalism may also facilitate the inclusion in these activities of important but neglected groups, especially among the invertebrates, and perhaps even microorganisms. Copyright © 1994. Published by Elsevier Ltd.

  2. WasteWise Resource Management: Innovative Solid Waste Contracting Methods

    Science.gov (United States)

    Resource management is an innovative contractual partnership between a waste-generating organization and a qualified contractor that changes the nature of current disposal services to support waste minimization and recycling.

  3. Bio-effectors from waste materials as growth promoters for tomato plants, an agronomic and metabolomic study

    Science.gov (United States)

    Abou Chehade, Lara; Chami, Ziad Al; De Pascali, Sandra; Cavoski, Ivana; Fanizzi, Francesco Paolo

    2015-04-01

    In organic farming, where nutrient management is constrained and sustainability is claimed, bio-effectors pave their way. Considering selected bio-effectors, this study integrates metabolomics to agronomy in depicting induced relevant phenomena. Extracts of three agro-industrial wastes (Lemon processing residues, Fennel processing residues and Brewer's spent grain) are being investigated as sources of bio-effectors for the third trial consequently. Corresponding individual and mixture aqueous extracts are assessed for their synergistic and/or single agronomic and qualitative performances on soil-grown tomato, compared to both a control and humic acid treatments. A metabolomic profiling of tomato fruits via the Proton Nuclear Magnetic Resonance (NMR) spectroscopy, as holistic indicator of fruit quality and extract-induced responses, complements crop productivity and organoleptic/nutritional qualitative analyses. Results are expected to show mainly an enhancement of the fruit qualitative traits, and to confirm partly the previous results of better crop productivity and metabolism enhancement. Waste-derived bio-effectors could be, accordingly, demonstrated as potential candidates of plant-enhancing substances. Keywords: bio-effectors, organic farming, agro-industrial wastes, nuclear magnetic resonance (NMR), tomato.

  4. Recycling - Danish Waste Management Strategy

    DEFF Research Database (Denmark)

    Romann, Anne Funch; Thøgersen, John; Husmer, Lis

    The report challanges recycling as the only waste handling strategy. The tonnes of recycled materials should not be the only goal - it is essential to minimize the waste production and focus on eliminating hazardous materials.......The report challanges recycling as the only waste handling strategy. The tonnes of recycled materials should not be the only goal - it is essential to minimize the waste production and focus on eliminating hazardous materials....

  5. The annual Hajj pilgrimage-minimizing the risk of ill health in pilgrims from Europe and opportunity for driving the best prevention and health promotion guidelines.

    Science.gov (United States)

    Shafi, Shuja; Dar, Osman; Khan, Mishal; Khan, Minal; Azhar, Esam I; McCloskey, Brian; Zumla, Alimuddin; Petersen, Eskild

    2016-06-01

    Mass gatherings at religious events can pose major public health challenges, particularly the transmission of infectious diseases. Every year the Kingdom of Saudi Arabia (KSA) hosts the Hajj pilgrimage, the largest gathering held on an annual basis where over 2 million people come to KSA from over 180 countries. Living together in crowded conditions exposes the pilgrims and the local population to a range infectious diseases. Respiratory and gastrointestinal tract bacterial and viral infections can spread rapidly and affect attendees of mass gatherings. Lethal infectious disease outbreaks were common during Hajj in the 19th and 20th centuries although they have now been controlled to a great extent by the huge investments made by the KSA into public health prevention and surveillance programs. The KSA provides regular updated Hajj travel advice and health regulations through international public health agencies such as the WHO, Public Health England, the Centers for Disease Control and Prevention, and Hajj travel agencies. During the Hajj, an additional 25 000 health workers are deployed; there are eight hospitals in Makkah and Mina complete with state-of-the-art surgical wards and intensive care units made specifically available for pilgrims. All medical facilities offer high quality of care, and services are offered free to Hajj pilgrims to ensure the risks of ill health to all pilgrims and KSA residents are minimal. A summary of the key health issues that arise in pilgrims from Europe during Hajj and of the KSA Hajj guidelines, together with other factors that may play a role in reducing the risks to pilgrims and to wider global health security, is provided herein. Copyright © 2016. Published by Elsevier Ltd.

  6. Synthesis of waste cooking oil based biodiesel via ferric-manganese promoted molybdenum oxide / zirconia nanoparticle solid acid catalyst: influence of ferric and manganese dopants.

    Science.gov (United States)

    Alhassan, Fatah H; Rashid, Umer; Taufiq-Yap, Yun Hin

    2015-01-01

    The utilization of ferric-manganese promoted molybdenum oxide/zirconia (Fe-Mn- MoO3/ZrO2) (FMMZ) solid acid catalyst for production of biodiesel was demonstrated. FMMZ is produced through impregnation reaction followed by calcination at 600°C for 3 h. The characterization of FMMZ had been done using X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), thermal gravimetric analysis (TGA), temperature programmed desorption of NH3 (TPD-NH3), transmission electron microscopy(TEM) and Brunner-Emmett-Teller (BET) surface area measurement. The effect of waste cooking oil methyl esters (WCOME's) yield on the reactions variables such as reaction temperature, catalyst loading, molar ratio of methanol/oil and reusability were also assessed. The catalyst was used to convert the waste cooking oil into corresponding methyl esters (95.6%±0.15) within 5 h at 200℃ reaction temperature, 600 rpm stirring speed, 1:25 molar ratio of oil to alcohol and 4% w/w catalyst loading. The reported catalyst was successfully recycled in six connective experiments without loss in activity. Moreover, the fuel properties of WCOME's were also reported using ASTM D 6751 methods.

  7. Hazardous Waste Minimization Assessment: Fort Campbell, Kentucky

    Science.gov (United States)

    1991-03-01

    during WWII and served as a prisoner of war (POW) detention center for 4,000 German soldiers between mid-1943 and April 1946. In June 1948, the...DNT) pp Nitroglycerin (NG) PP Nitroguanidine (NQ) PP Dibutyl phthalate PP Diethyl phthalate PP Diphenylamine PP Benzene EX Toluene EX Sodium Nitrate Py

  8. Waste Minimization Program. Air Force Plant 78.

    Science.gov (United States)

    1986-02-01

    AFP 78 degreasers are over 23 years old and are * approaching the end of their useful lives. Replacement with new units, particularly the Circo ...to degreaser operation. Specifically, the large Circo degreaser used to clean mandrils probably loses significant amounts of vapor due to piston...508 Circo Power $15,000 $ 300 $ 30,400 0.5 Cover M-508 Detrex Power $ 4,000 1 LO0 $ 1,900 2.2 Cover *M-605-Detrex Power $ 4,000 $ 00 $ 5,300 0.8 4

  9. Report on the project for spread/promotion of technology for the industrial waste optimized treatment in the Asian region (International Symposium `98); Asia chiiki sangyo haikibutsu tekiseika shori gijutsu nado fukyu sokushin jigyo (symposium kaisai) hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    In Japan and Asian countries, the optimized treatment of industrial waste is the problem with the economic growth. Border-crossing movement of the waste for promotion of the renewable use is also a problem. Therefore, the International Symposium `98 on the industrial waste problem in the Asian region was held. China, Thailand, the Philippines and Korea were invited to Japan to give lectures. MITI of Japan reported on the present situation of Japan and the cooperation with Asian countries. The industrial circle reported on efforts for environmental protection measures to be taken, the industrial waste problem at companies which advanced into Asian countries, effects of the Basel Convention on recycling activities, Japan`s role in Asia, etc. In the panel discussion, promotion of cooperation for recycling technology and Japan`s support for formulating strategy on the industrial waste were requested to Japan, and the construction of an Asian area network was proposed. Concerning the cooperative system between governments and private companies, it was concluded that it was necessary to discuss it considering the actual state of each country. Importance of recycle and information exchange was realized again. 10 refs., 15 figs., 27 tabs.

  10. Mixed waste: Proceedings

    Energy Technology Data Exchange (ETDEWEB)

    Moghissi, A.A.; Blauvelt, R.K.; Benda, G.A.; Rothermich, N.E. [eds.] [Temple Univ., Philadelphia, PA (United States). Dept. of Environmental Safety and Health

    1993-12-31

    This volume contains the peer-reviewed and edited versions of papers submitted for presentation a the Second International Mixed Waste Symposium. Following the tradition of the First International Mixed Waste Symposium, these proceedings were prepared in advance of the meeting for distribution to participants. The symposium was organized by the Mixed Waste Committee of the American Society of Mechanical Engineers. The topics discussed at the symposium include: stabilization technologies, alternative treatment technologies, regulatory issues, vitrification technologies, characterization of wastes, thermal technologies, laboratory and analytical issues, waste storage and disposal, organic treatment technologies, waste minimization, packaging and transportation, treatment of mercury contaminated wastes and bioprocessing, and environmental restoration. Individual abstracts are catalogued separately for the data base.

  11. Waste audit pada industri penyamakan kulit

    Directory of Open Access Journals (Sweden)

    Prayitno Prayitno

    1999-07-01

    Full Text Available Waste audit is new environmental activities. to the Indonesia public and the large part of industrial community it is one of the environmental audit activities. Waste audit aims to identify whether the waste that by the industry waste so that metods for minimizing the waste can be found. In the leather tanning industry wasted audit is performend for every step pg the process, started from the raw material strage to the fishing ptocess.

  12. Mixed waste management options

    Energy Technology Data Exchange (ETDEWEB)

    Owens, C.B.; Kirner, N.P. [EG and G Idaho, Inc., Idaho Falls, ID (United States). Idaho National Engineering Lab.

    1991-12-31

    Disposal fees for mixed waste at proposed commercial disposal sites have been estimated to be $15,000 to $40,000 per cubit foot. If such high disposal fees are imposed, generators may be willing to apply extraordinary treatment or regulatory approaches to properly dispose of their mixed waste. This paper explores the feasibility of several waste management scenarios and attempts to answer the question: Can mixed waste be managed out of existence? Existing data on commercially generated mixed waste streams are used to identify the realm of mixed waste known to be generated. Each waste stream is evaluated from both a regulatory and technical perspective in order to convert the waste into a strictly low-level radioactive or a hazardous waste. Alternative regulatory approaches evaluated in this paper include a delisting petition, no migration petition, and a treatability variance. For each waste stream, potentially available treatment options are identified that could lead to these variances. Waste minimization methodology and storage for decay are also considered. Economic feasibility of each option is discussed broadly.

  13. Socio-technical systems analysis of waste to energy from municipal solid waste in developing economies: a case for Nigeria

    Directory of Open Access Journals (Sweden)

    Iyamu Hope O.

    2017-01-01

    Full Text Available Waste generation is an inevitable by-product of human activity, and it is on the rise due to rapid urbanisation, industrialisation, increased wealth and population. The composition of municipal solid waste (MSW in developed and developing economies differ, especially with the organic fraction. Research shows that the food waste stream of MSW in developing countries is over 50%. The case study for this investigation, Nigeria, has minimal formal recycling or resource recovery programs. The average composition of waste from previous research in the country is between 50–70% putrescible and 30–50% non-putrescible, presenting significant resource recovery potential in composting and biogas production. Waste-to-energy (WtE is an important waste management solution that has been successfully implemented and operated in most developed economies. This contribution reports the conditions that would be of interest before WtE potentials of MSW is harnessed, in an efficient waste management process in a developing economy like Nigeria. The investigation presents a set of socio-technical parameters and transition strategy model that would inform a productive MSW management and resource recovery, in which WtE can be part of the solution. This model will find application in the understanding of the interactions between the socio-economic, technical and environmental system, to promote sustainable resource recovery programs in developing economies, among which is WtE.

  14. 76 FR 59960 - Hazardous Waste Management System; Identification and Listing of Hazardous Waste; Withdrawal of...

    Science.gov (United States)

    2011-09-28

    ... AGENCY 40 CFR Part 261 Hazardous Waste Management System; Identification and Listing of Hazardous Waste... Planning and Permitting Division, Corrective Action and Waste Minimization Section (6PD-C), 1445 Ross... will be taken on this petition. A new petition will be required for this waste stream. List of Subjects...

  15. Report on the research cooperation promoting project in fiscal 1998. Research cooperation related to the mine waste water treatment technology utilizing biomass; 1998 nendo kenkyu kyoryoku suishin jigyo hokokusho. Bio riyo ni yoru kohaisui shori gijutsu ni kansuru kyoryoku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This paper describes the achievement in relation with the mine waste water treatment technology utilizing biomass, from among the promotion projects for research cooperation with China. Waste water is converted into ferric iron (Fe{sup 3+}), which precipitates at low pH, by utilizing iron oxidizing bacteria which use ferrous iron (Fe{sup 2+}) in the waste water as the energy source, and is precipitated and removed by using low-cost calcium carbonate as a neutralizing agent. Fiscal 1998 has performed eight site surveys with 47 persons in total. The main survey items are the study and guidance of pilot plant operation and the survey on measures to prevent occurrence of contamination by heavy metals in Wushan Mine. Additional site surveys were made at Dexing Mine and Yinshan Lead/Zinc Mine. Continued from fiscal 1997, consumables required for the pilot plant were purchased, and items of the bench-scale testing equipment used by Japan for domestic researches (an oxidation and neutralization testing equipment and a copper recovering and testing equipment) were transported to China. The operation research data of the pilot plant were put in order and analyzed. This paper summarizes the concept design of the shaft waste water treatment facilities for the north mine in Wushan Mine, and the surveys on measures for heavy metal contamination sources. (NEDO)

  16. Thinking and acting strategically: promoting integrated solid waste management and corporate responsibility through a public private partnership; the case of Altamira, Tamaulipas, Mexico

    Directory of Open Access Journals (Sweden)

    Bernhard Bösl

    2010-09-01

    Full Text Available This article provides an assessment of a public private partnerships (PPP among the German Technical Cooperation (GTZ, the Municipality of Altamira, Tamaulipas, Mexico and private counterparts BASF Mexicana and Terminal de LNG de Altamira (TLA. The municipality of Altamira, located in the urban-industrial hub of southern Tamaulipas, Mexico, faces important challenges in the field of urban public service delivery, particularly waste management, due to a high demographic growth rate and chronic budgetary constraints. The partnership was formed as a means to develop and implement the Municipal Program for the Prevention and Integrated Management of Solid and Special Wastes. The paper discusses the efficacy of the PPP as a policy instrument for the implementation of integrated solid waste management. As an assessment method, the authors draw on GTZ’s success criteria for the cooperation with the private sector. Criteria include the degree of complementarity, subsidiarity, neutrality and quality of private sector contributions. We argue that this PPP displays a pioneering alliance structure, since the private sector becomes a direct ally in creating strategies for the promotion sustainable development and not simply an exclusive contractor for urban public services delivery or a recipient of incentives from international development cooperation. The PPP provides a means to reach corporate social and environmental responsibility goals while at the same time it promotes development-related policy goals enshrined in the bilateral cooperation agreement between Germany and Mexico. However, the alliance faces important challenges related to different organizational cultures, electoral times and citizen participation.Cet article évalue un partenariat public-privé (PPP entre GTZ (société allemande de coopération technique, la municipalité d’Altamira, dans l’état du Tamaulipas au Mexique et deux homologues privés : BASF Mexicana et Terminal de

  17. Waste reduction plan for The Oak Ridge National Laboratory

    Energy Technology Data Exchange (ETDEWEB)

    Schultz, R.M.

    1990-04-01

    The Oak Ridge National Laboratory (ORNL) is a multipurpose Research and Development (R D) facility. These R D activities generate numerous small waste streams. Waste minimization is defined as any action that minimizes the volume or toxicity of waste by avoiding its generation or recycling. This is accomplished by material substitution, changes to processes, or recycling wastes for reuse. Waste reduction is defined as waste minimization plus treatment which results in volume or toxicity reduction. The ORNL Waste Reduction Program will include both waste minimization and waste reduction efforts. Federal regulations, DOE policies and guidelines, increased costs and liabilities associated with the management of wastes, limited disposal options and facility capacities, and public consciousness have been motivating factors for implementing comprehensive waste reduction programs. DOE Order 5820.2A, Section 3.c.2.4 requires DOE facilities to establish an auditable waste reduction program for all LLW generators. In addition, it further states that any new facilities, or changes to existing facilities, incorporate waste minimization into design considerations. A more recent DOE Order, 3400.1, Section 4.b, requires the preparation of a waste reduction program plan which must be reviewed annually and updated every three years. Implementation of a waste minimization program for hazardous and radioactive mixed wastes is sited in DOE Order 5400.3, Section 7.d.5. This document has been prepared to address these requirements. 6 refs., 1 fig., 2 tabs.

  18. Solid medical waste

    DEFF Research Database (Denmark)

    Udofia, Emilia Asuquo; Gulis, Gabriel; Fobil, Julius

    2017-01-01

    BACKGROUND: Solid medical waste (SMW) in households is perceived to pose minimal risks to the public compared to SMW generated from healthcare facilities. While waste from healthcare facilities is subject to recommended safety measures to minimize risks to human health and the environment, similar......-demographic characteristics, medication related practices, the belief that one is at risk of diseases associated with SMW, SMW disposal practices and reported harm associated with SMW at home and in the community. RESULTS: Eighty percent and 89% of respondents discarded unwanted medicines and sharps in household refuse bins...

  19. Alternativas de minimização de resíduos em uma indústria de alimentos da região metropolitana de Curitiba Waste minimization measures in a food industry located in the metropolitan area of Curitiba

    Directory of Open Access Journals (Sweden)

    Bárbara Zanicotti Leite

    2005-06-01

    with a mathematical model to obtain the order of minimization. The organic natural waste, even from the productive process as from the wastewather treatment plant, were selected as priorities. The fourth stage of the waste minimization programme was the proposition of the minimization measures. The main recomendations were:: training the employers, ajustment and control at the time of the equipments, temperature, flow, and raw material specification control at the time of reception. The waste minimization is a good option for the environmental management of the food industry because besides reducing costs with waste disposal and treatment, it also increases production process efficiency.

  20. Sustainable Waste Management for Green Highway Initiatives

    Directory of Open Access Journals (Sweden)

    Husin Nur Illiana

    2016-01-01

    Full Text Available Green highway initiative is the transportation corridors based on sustainable concept of roadway. It incorporates both transportation functionality and ecological requirements. Green highway also provides more sustainable construction technique that maximizes the lifespan of highway. Waste management is one of the sustainable criterias in the elements of green highway. Construction of highway consumes enormous amounts of waste in term of materials and energy. These wastes need to be reduce to sustain the environment. This paper aims to identify the types of waste produced from highway construction. Additionally, this study also determine the waste minimization strategy and waste management practiced.. This study main focus are construction and demolition waste only. The methodology process begin with data collection by using questionnaire survey. 22 concession companies listed under Lembaga Lebuhraya Malaysia acted as a respondent. The questionnaires were distributed to all technical department staffs. The data received was analyzed using IBM SPSS. The results shows the most production of waste is wood, soil, tree root and concrete. The least production of waste is metal. For waste minimization, the best waste minimization is reuse for all type of waste except for tree root and stump. Whereas, the best waste management is providing strategic plan. The least practice for waste management is recording the quantity of waste.

  1. Increasingly minimal bias routing

    Science.gov (United States)

    Bataineh, Abdulla; Court, Thomas; Roweth, Duncan

    2017-02-21

    A system and algorithm configured to generate diversity at the traffic source so that packets are uniformly distributed over all of the available paths, but to increase the likelihood of taking a minimal path with each hop the packet takes. This is achieved by configuring routing biases so as to prefer non-minimal paths at the injection point, but increasingly prefer minimal paths as the packet proceeds, referred to herein as Increasing Minimal Bias (IMB).

  2. Waste Sites - Municipal Waste Operations

    Data.gov (United States)

    NSGIC Education | GIS Inventory — A Municipal Waste Operation is a DEP primary facility type related to the Waste Management Municipal Waste Program. The sub-facility types related to Municipal Waste...

  3. Avoidable waste management costs

    Energy Technology Data Exchange (ETDEWEB)

    Hsu, K.; Burns, M.; Priebe, S.; Robinson, P.

    1995-01-01

    This report describes the activity based costing method used to acquire variable (volume dependent or avoidable) waste management cost data for routine operations at Department of Energy (DOE) facilities. Waste volumes from environmental restoration, facility stabilization activities, and legacy waste were specifically excluded from this effort. A core team consisting of Idaho National Engineering Laboratory, Los Alamos National Laboratory, Rocky Flats Environmental Technology Site, and Oak Ridge Reservation developed and piloted the methodology, which can be used to determine avoidable waste management costs. The method developed to gather information was based on activity based costing, which is a common industrial engineering technique. Sites submitted separate flow diagrams that showed the progression of work from activity to activity for each waste type or treatability group. Each activity on a flow diagram was described in a narrative, which detailed the scope of the activity. Labor and material costs based on a unit quantity of waste being processed were then summed to generate a total cost for that flow diagram. Cross-complex values were calculated by determining a weighted average for each waste type or treatability group based on the volume generated. This study will provide DOE and contractors with a better understanding of waste management processes and their associated costs. Other potential benefits include providing cost data for sites to perform consistent cost/benefit analysis of waste minimization and pollution prevention (WMIN/PP) options identified during pollution prevention opportunity assessments and providing a means for prioritizing and allocating limited resources for WMIN/PP.

  4. System dynamics-based evaluation of interventions to promote appropriate waste disposal behaviors in low-income urban areas: A Baltimore case study.

    Science.gov (United States)

    Guo, Huaqing; Hobbs, Benjamin F; Lasater, Molly E; Parker, Cindy L; Winch, Peter J

    2016-10-01

    Inappropriate waste disposal is a serious issue in many urban neighborhoods, exacerbating environmental, rodent, and public health problems. Governments all over the world have been developing interventions to reduce inappropriate waste disposal. A system dynamics model is proposed to quantify the impacts of interventions on residential waste related behavior. In contrast to other models of municipal solid waste management, the structure of our model is based on sociological and economic studies on how incentives and social norms interactively affect waste disposal behavior, and its parameterization is informed by field work. A case study of low-income urban neighborhoods in Baltimore, MD, USA is presented. The simulation results show the effects of individual interventions, and also identify positive interactions among some potential interventions, especially information and incentive-based policies, as well as their limitations. The model can help policy analysts identify the most promising intervention packages, and then field test those few, rather than having to pilot test all combinations. Sensitivity analyses demonstrate large uncertainties about behavioral responses to some interventions, showing where information from survey research and social experiments would improve policy making. Copyright © 2016 Elsevier Ltd. All rights reserved.

  5. Residential Waste

    DEFF Research Database (Denmark)

    Christensen, Thomas Højlund; Fruergaard, Thilde; Matsufuji, Y.

    2011-01-01

    Residential waste comes from residential areas with multi-family and single-family housing and includes four types of waste: household waste, garden waste, bulky waste and household hazardous waste. Typical unit generation rates, material composition, chemical composition and determining factors...... are discussed in this chapter. Characterizing residential waste is faced with the problem that many residences already divert some waste away from the official collection systems, for example performing home composting of vegetable waste and garden waste, having their bundled newspaper picked up by the scouts...... twice a year or bringing their used furniture to the flea markets organized by charity clubs. Thus, much of the data available on residential waste represents collected waste and not necessarily all generated waste. The latter can only be characterized by careful studies directly at the source...

  6. Correlates of minimal dating.

    Science.gov (United States)

    Leck, Kira

    2006-10-01

    Researchers have associated minimal dating with numerous factors. The present author tested shyness, introversion, physical attractiveness, performance evaluation, anxiety, social skill, social self-esteem, and loneliness to determine the nature of their relationships with 2 measures of self-reported minimal dating in a sample of 175 college students. For women, shyness, introversion, physical attractiveness, self-rated anxiety, social self-esteem, and loneliness correlated with 1 or both measures of minimal dating. For men, physical attractiveness, observer-rated social skill, social self-esteem, and loneliness correlated with 1 or both measures of minimal dating. The patterns of relationships were not identical for the 2 indicators of minimal dating, indicating the possibility that minimal dating is not a single construct as researchers previously believed. The present author discussed implications and suggestions for future researchers.

  7. Minimally invasive orthognathic surgery.

    Science.gov (United States)

    Resnick, Cory M; Kaban, Leonard B; Troulis, Maria J

    2009-02-01

    Minimally invasive surgery is defined as the discipline in which operative procedures are performed in novel ways to diminish the sequelae of standard surgical dissections. The goals of minimally invasive surgery are to reduce tissue trauma and to minimize bleeding, edema, and injury, thereby improving the rate and quality of healing. In orthognathic surgery, there are two minimally invasive techniques that can be used separately or in combination: (1) endoscopic exposure and (2) distraction osteogenesis. This article describes the historical developments of the fields of orthognathic surgery and minimally invasive surgery, as well as the integration of the two disciplines. Indications, techniques, and the most current outcome data for specific minimally invasive orthognathic surgical procedures are presented.

  8. Minimal Super Technicolor

    DEFF Research Database (Denmark)

    Antola, M.; Di Chiara, S.; Sannino, F.

    2011-01-01

    We introduce novel extensions of the Standard Model featuring a supersymmetric technicolor sector (supertechnicolor). As the first minimal conformal supertechnicolor model we consider N=4 Super Yang-Mills which breaks to N=1 via the electroweak interactions. This is a well defined, economical......, between unparticle physics and Minimal Walking Technicolor. We consider also other N =1 extensions of the Minimal Walking Technicolor model. The new models allow all the standard model matter fields to acquire a mass....

  9. Lyophilization -Solid Waste Treatment

    Science.gov (United States)

    Litwiller, Eric; Flynn, Michael; Fisher, John; Reinhard, Martin

    2004-01-01

    This paper discusses the development of a solid waste treatment system that has been designed for a Mars transit exploration mission. The technology described is an energy-efficient lyophilization technique that is designed to recover water from spacecraft solid wastes. Candidate wastes include feces, concentrated brines from water processors, and other solid wastes that contain free water. The system is designed to operate as a stand-alone process or to be integrated into the International Space Station Waste Collection System. In the lyophilization process, water in an aqueous waste is frozen and then sublimed, separating the waste into a dried solid material and liquid water. The sublimed water is then condensed in a solid ice phase and then melted to generate a liquid product. In the subject system the waste solids are contained within a 0.2 micron bio-guard bag and after drying are removed from the system and stored in a secondary container. This technology is ideally suited to applications such as the Mars Reference Mission, where water recovery rates approaching 100% are desirable but production of CO2 is not. The system is designed to minimize power consumption through the use of thermoelectric heat pumps. The results of preliminary testing of a prototype system and testing of the final configuration are provided. A mathematical model of the system is also described.

  10. Investigating the determinants of contractor's construction and demolition waste management behavior in Mainland China.

    Science.gov (United States)

    Wu, Zezhou; Yu, Ann T W; Shen, Liyin

    2017-02-01

    The abundant generation of construction and demolition (C&D) waste presents a significant challenge to the sustainable development of the construction industry in Mainland China. As the implementer of construction activities, the contractor's C&D waste management performance plays an important role in C&D waste minimization. This paper aims to investigate the determinants of the contractor's C&D waste management behavior in Mainland China. The Theory of Planned Behavior (TPB) was selected as the basis of the theoretical model. In addition, three contextual constructs (i.e., economic viability, governmental supervision, and project constraints) were introduced, formulating the initial model. Based on the initial model, eight constructs were identified and seven hypotheses were proposed. A questionnaire survey was conducted to collect data and a Structural Equation Modeling (SEM) analysis was employed to test the proposed hypotheses. Results showed that the C&D waste management intention is not a significant determinant of contractor's C&D waste management behavior. The most important determinant is economic viability, followed by governmental supervision as the second most important determinant. Nevertheless, the construct of project constraints is an insignificant determinant for contractor's adoption of C&D waste management behavior. The research findings imply that, in Mainland China, the government, at this stage, plays an important role in guiding and promoting the contractor to exhibit better C&D waste management behavior. Copyright © 2016 Elsevier Ltd. All rights reserved.

  11. Hazardous Waste

    Science.gov (United States)

    ... you throw these substances away, they become hazardous waste. Some hazardous wastes come from products in our homes. Our garbage can include such hazardous wastes as old batteries, bug spray cans and paint ...

  12. Minimizing Mutual Couping

    DEFF Research Database (Denmark)

    2010-01-01

    Disclosed herein are techniques, systems, and methods relating to minimizing mutual coupling between a first antenna and a second antenna.......Disclosed herein are techniques, systems, and methods relating to minimizing mutual coupling between a first antenna and a second antenna....

  13. Minimally invasive lumbar fusion.

    Science.gov (United States)

    Foley, Kevin T; Holly, Langston T; Schwender, James D

    2003-08-01

    Review article. To provide an overview of current techniques for minimally invasive lumbar fusion. Minimally invasive techniques have revolutionized the management of pathologic conditions in various surgical disciplines. Although these same principles have been used in the treatment of lumbar disc disease for many years, minimally invasive lumbar fusion procedures have only recently been developed. The goals of these procedures are to reduce the approach-related morbidity associated with traditional lumbar fusion, yet allow the surgery to be performed in an effective and safe manner. The authors' clinical experience with minimally invasive lumbar fusion was reviewed, and the pertinent literature was surveyed. Minimally invasive approaches have been developed for common lumbar procedures such as anterior and posterior interbody fusion, posterolateral onlay fusion, and internal fixation. As with all new surgical techniques, minimally invasive lumbar fusion has a learning curve. As well, there are benefits and disadvantages associated with each technique. However, because these techniques are new and evolving, evidence to support their potential benefits is largely anecdotal. Additionally, there are few long-term studies to document clinical outcomes. Preliminary clinical results suggest that minimally invasive lumbar fusion will have a beneficial impact on the care of patients with spinal disorders. Outcome studies with long-term follow-up will be necessary to validate its success and allow minimally invasive lumbar fusion to become more widely accepted.

  14. Waste Management Decision-Making Process During a Homeland Security Incident Response

    Science.gov (United States)

    A step-by-step guide on how to make waste management-related decisions including how waste can be minimized, collected and treated, as well as where waste can be sent for staging, storage and final disposal.

  15. Collection and Segregation of Radioactive Waste. Principals for Characterization and Classification of Radioactive Waste

    Energy Technology Data Exchange (ETDEWEB)

    Dziewinska, K.M.

    1998-09-28

    Radioactive wastes are generated by all activities which utilize radioactive materials as part of their processes. Generally such activities include all steps in the nuclear fuel cycle (for power generation) and non-fuel cycle activities. The increasing production of radioisotopes in a Member State without nuclear power must be accompanied by a corresponding development of a waste management system. An overall waste management scheme consists of the following steps: segregation, minimization, treatment, conditioning, storage, transport, and disposal. To achieve a satisfactory overall management strategy, all steps have to be complementary and compatible. Waste segregation and minimization are of great importance mainly because they lead to cost reduction and reduction of dose commitments to the personnel that handle the waste. Waste characterization plays a significant part in the waste segregation and waste classification processes, it implicates required waste treatment process including the need for the safety assessment of treatment conditioning and storage facilities.

  16. Cement encapsulation of intermediate-level waste slurries

    Energy Technology Data Exchange (ETDEWEB)

    Lewis, H.G.; Cassidy, C.M. [British Nuclear Fuels plc, Risley (United Kingdom)

    1993-12-31

    Reprocessing of irradiated nuclear fuel at BNFL`s Sellafield site produces a range of radioactive wastes. BNFL has adopted a detailed policy for radioactive waste management in order that: effluent discharges to the environment are minimized, solid low-level waste is safely disposed of as it arises, and all other wastes are stored, conditioned and treated for eventual disposal.

  17. Plasma filtering techniques for nuclear waste remediation.

    Science.gov (United States)

    Gueroult, Renaud; Hobbs, David T; Fisch, Nathaniel J

    2015-10-30

    Nuclear waste cleanup is challenged by the handling of feed stocks that are both unknown and complex. Plasma filtering, operating on dissociated elements, offers advantages over chemical methods in processing such wastes. The costs incurred by plasma mass filtering for nuclear waste pretreatment, before ultimate disposal, are similar to those for chemical pretreatment. However, significant savings might be achieved in minimizing the waste mass. This advantage may be realized over a large range of chemical waste compositions, thereby addressing the heterogeneity of legacy nuclear waste. Copyright © 2015 Elsevier B.V. All rights reserved.

  18. Material Recovery and Waste Form Development FY 2014 Accomplishments Report

    Energy Technology Data Exchange (ETDEWEB)

    Braase, Lori [Idaho National Lab. (INL), Idaho Falls, ID (United States)

    2014-11-01

    Develop advanced nuclear fuel cycle separation and waste management technologies that improve current fuel cycle performance and enable a sustainable fuel cycle, with minimal processing, waste generation, and potential for material diversion.

  19. Ruled Laguerre minimal surfaces

    KAUST Repository

    Skopenkov, Mikhail

    2011-10-30

    A Laguerre minimal surface is an immersed surface in ℝ 3 being an extremal of the functional ∫ (H 2/K-1)dA. In the present paper, we prove that the only ruled Laguerre minimal surfaces are up to isometry the surfaces ℝ (φλ) = (Aφ, Bφ, Cφ + D cos 2φ) + λ(sin φ, cos φ, 0), where A,B,C,D ε ℝ are fixed. To achieve invariance under Laguerre transformations, we also derive all Laguerre minimal surfaces that are enveloped by a family of cones. The methodology is based on the isotropic model of Laguerre geometry. In this model a Laguerre minimal surface enveloped by a family of cones corresponds to a graph of a biharmonic function carrying a family of isotropic circles. We classify such functions by showing that the top view of the family of circles is a pencil. © 2011 Springer-Verlag.

  20. Minimalism. Clip and Save.

    Science.gov (United States)

    Hubbard, Guy

    2002-01-01

    Provides background information on the art movement called "Minimalism" discussing why it started and its characteristics. Includes learning activities and information on the artist, Donald Judd. Includes a reproduction of one of his art works and discusses its content. (CMK)

  1. Minimally processed fruit salad enriched with Lactobacillus ...

    African Journals Online (AJOL)

    paula

    2015-06-17

    Jun 17, 2015 ... 1Food Science and Technology Department, Federal Institute of Education, Science and Technology of Southeast of. Minas Gerais ... Minimal processing promotes browning of some vegetal tissues due to cell membrane disruption, which .... polypyrrolidone (PVPP), three drops of Triton X-100 and 20 mL of.

  2. Storing Waste in Ceramic

    Energy Technology Data Exchange (ETDEWEB)

    Bourcier, W L; Sickafus, K

    2004-07-20

    Not all the nuclear waste destined for Yucca Mountain is in the form of spent fuel. Some of it will be radioactive waste generated from the production of nuclear weapons. This so-called defense waste exists mainly as corrosive liquids and sludge in underground tanks. An essential task of the U.S. high-level radioactive waste program is to process these defense wastes into a solid material--called a waste form. An ideal waste form would be extremely durable and unreactive with other repository materials. It would be simple to fabricate remotely so that it could be safely transported to a repository for permanent storage. What's more, the material should be able to tolerate exposure to intense radiation without degradation. And to minimize waste volume, the material must be able to contain high concentrations of radionuclides. The material most likely to be used for immobilization of radioactive waste is glass. Glasses are produced by rapid cooling of high-temperature liquids such that the liquid-like non-periodic structure is preserved at lower temperatures. This rapid cooling does not allow enough time for thermodynamically stable crystalline phases (mineral species) to form. In spite of their thermodynamic instability, glasses can persist for millions of years. An alternate to glass is a ceramic waste form--an assemblage of mineral-like crystalline solids that incorporate radionuclides into their structures. The crystalline phases are thermodynamically stable at the temperature of their synthesis; ceramics therefore tend to be more durable than glasses. Ceramic waste forms are fabricated at temperatures below their melting points and so avoid the danger of handling molten radioactive liquid--a danger that exists with incorporation of waste in glasses. The waste form provides a repository's first line of defense against release of radionuclides. It, along with the canister, is the barrier in the repository over which we have the most control. When a waste

  3. Gaseous emissions from management of solid waste: a systematic review

    Science.gov (United States)

    Pardo, Guillermo; Moral, Raúl; Aguilera, Eduardo; del Prado, Agustín

    2015-01-01

    The establishment of sustainable soil waste management practices implies minimizing their environmental losses associated with climate change (greenhouse gases: GHGs) and ecosystems acidification (ammonia: NH3). Although a number of management strategies for solid waste management have been investigated to quantify nitrogen (N) and carbon (C) losses in relation to varied environmental and operational conditions, their overall effect is still uncertain. In this context, we have analyzed the current scientific information through a systematic review. We quantified the response of GHG emissions, NH3 emissions, and total N losses to different solid waste management strategies (conventional solid storage, turned composting, forced aerated composting, covering, compaction, addition/substitution of bulking agents and the use of additives). Our study is based on a meta-analysis of 50 research articles involving 304 observations. Our results indicated that improving the structure of the pile (waste or manure heap) via addition or substitution of certain bulking agents significantly reduced nitrous oxide (N2O) and methane (CH4) emissions by 53% and 71%, respectively. Turned composting systems, unlike forced aerated composted systems, showed potential for reducing GHGs (N2O: 50% and CH4: 71%). Bulking agents and both composting systems involved a certain degree of pollution swapping as they significantly promoted NH3 emissions by 35%, 54%, and 121% for bulking agents, turned and forced aerated composting, respectively. Strategies based on the restriction of O2 supply, such as covering or compaction, did not show significant effects on reducing GHGs but substantially decreased NH3 emissions by 61% and 54% for covering and compaction, respectively. The use of specific additives significantly reduced NH3 losses by 69%. Our meta-analysis suggested that there is enough evidence to refine future Intergovernmental Panel on Climate Change (IPCC) methodologies from solid waste

  4. Minimalism and Speakers’ Intuitions

    Directory of Open Access Journals (Sweden)

    Matías Gariazzo

    2011-08-01

    Full Text Available Minimalism proposes a semantics that does not account for speakers’ intuitions about the truth conditions of a range of sentences or utterances. Thus, a challenge for this view is to offer an explanation of how its assignment of semantic contents to these sentences is grounded in their use. Such an account was mainly offered by Soames, but also suggested by Cappelen and Lepore. The article criticizes this explanation by presenting four kinds of counterexamples to it, and arrives at the conclusion that minimalism has not successfully answered the above-mentioned challenge.

  5. Minimal Walking Technicolor

    DEFF Research Database (Denmark)

    Frandsen, Mads Toudal

    2007-01-01

    I report on our construction and analysis of the effective low energy Lagrangian for the Minimal Walking Technicolor (MWT) model. The parameters of the effective Lagrangian are constrained by imposing modified Weinberg sum rules and by imposing a value for the S parameter estimated from the under......I report on our construction and analysis of the effective low energy Lagrangian for the Minimal Walking Technicolor (MWT) model. The parameters of the effective Lagrangian are constrained by imposing modified Weinberg sum rules and by imposing a value for the S parameter estimated from...

  6. Food waste valorization options: opportunities from the bioeconomy

    Directory of Open Access Journals (Sweden)

    Imbert Enrica

    2017-02-01

    Full Text Available The world is confronted with the depletion of natural resources due to their unsustainable use, increased global competiveness, increasing population and other environmental and economic challenges. Under the European 2020 growth strategy launched in 2010, Europe has set itself the goal of shifting from linear to circular models of production and consumption. In this context, food waste management poses a great challenge. This study focusses on the possible destinations for food waste, specifically, on the most sustainable practices that turn waste into valuable resources. Particular attention is devoted to the potential offered by fast-growing sectors such as the bioeconomy, which is contributing to increased energy and materials production with reduced environmental impact, at the same time creating new job opportunities. In this paper we will argue that an holistic approach considering the issue of food wastage as part of a broader emerging bio-economy and circular-economic model, might provide win-win solutions able to minimize wastage, promote income growth and job creation, and prompt sustainable local development. However, in order to enable an effective transition to a circular bioeconomy able to minimize the impact of food wastage, the economic, social, and environmental sustainability of this new model must be properly evaluated through appropriate tools, e.g. through an overall Life Cycle Sustainability Assessment (LCSA.

  7. Minimal DBM Substraction

    DEFF Research Database (Denmark)

    David, Alexandre; Håkansson, John; G. Larsen, Kim

    In this paper we present an algorithm to compute DBM substractions with a guaranteed minimal number of splits and disjoint DBMs to avoid any redundance. The substraction is one of the few operations that result in a non-convex zone, and thus, requires splitting. It is of prime importance to reduce...

  8. Minimal constrained supergravity

    Energy Technology Data Exchange (ETDEWEB)

    Cribiori, N. [Dipartimento di Fisica e Astronomia “Galileo Galilei”, Università di Padova, Via Marzolo 8, 35131 Padova (Italy); INFN, Sezione di Padova, Via Marzolo 8, 35131 Padova (Italy); Dall' Agata, G., E-mail: dallagat@pd.infn.it [Dipartimento di Fisica e Astronomia “Galileo Galilei”, Università di Padova, Via Marzolo 8, 35131 Padova (Italy); INFN, Sezione di Padova, Via Marzolo 8, 35131 Padova (Italy); Farakos, F. [Dipartimento di Fisica e Astronomia “Galileo Galilei”, Università di Padova, Via Marzolo 8, 35131 Padova (Italy); INFN, Sezione di Padova, Via Marzolo 8, 35131 Padova (Italy); Porrati, M. [Center for Cosmology and Particle Physics, Department of Physics, New York University, 4 Washington Place, New York, NY 10003 (United States)

    2017-01-10

    We describe minimal supergravity models where supersymmetry is non-linearly realized via constrained superfields. We show that the resulting actions differ from the so called “de Sitter” supergravities because we consider constraints eliminating directly the auxiliary fields of the gravity multiplet.

  9. Minimally invasive periodontal therapy.

    Science.gov (United States)

    Dannan, Aous

    2011-10-01

    Minimally invasive dentistry is a concept that preserves dentition and supporting structures. However, minimally invasive procedures in periodontal treatment are supposed to be limited within periodontal surgery, the aim of which is to represent alternative approaches developed to allow less extensive manipulation of surrounding tissues than conventional procedures, while accomplishing the same objectives. In this review, the concept of minimally invasive periodontal surgery (MIPS) is firstly explained. An electronic search for all studies regarding efficacy and effectiveness of MIPS between 2001 and 2009 was conducted. For this purpose, suitable key words from Medical Subject Headings on PubMed were used to extract the required studies. All studies are demonstrated and important results are concluded. Preliminary data from case cohorts and from many studies reveal that the microsurgical access flap, in terms of MIPS, has a high potential to seal the healing wound from the contaminated oral environment by achieving and maintaining primary closure. Soft tissues are mostly preserved and minimal gingival recession is observed, an important feature to meet the demands of the patient and the clinician in the esthetic zone. However, although the potential efficacy of MIPS in the treatment of deep intrabony defects has been proved, larger studies are required to confirm and extend the reported positive preliminary outcomes.

  10. Minimal constrained supergravity

    Directory of Open Access Journals (Sweden)

    N. Cribiori

    2017-01-01

    Full Text Available We describe minimal supergravity models where supersymmetry is non-linearly realized via constrained superfields. We show that the resulting actions differ from the so called “de Sitter” supergravities because we consider constraints eliminating directly the auxiliary fields of the gravity multiplet.

  11. Minimal Walking Technicolor

    DEFF Research Database (Denmark)

    Foadi, Roshan; Frandsen, Mads Toudal; A. Ryttov, T.

    2007-01-01

    , pseudoscalars, vector mesons and other fields predicted by the minimal walking theory. We construct their self-interactions and interactions with standard model fields. Using the Weinberg sum rules, opportunely modified to take into account the walking behavior of the underlying gauge theory, we find...

  12. Study of the dechroming of tanned leather wastes

    OpenAIRE

    Botić Tatjana; Ilišković Nadežda V.; Drljača Dijana

    2004-01-01

    According to European legislation, it is not possible to dump any chromium-containing waste in Europe. The minimization of wastes is a key element in that strategy. It involves the application of clean technologies: low and non-waste technologies. The tanning industry generates substantial quantities of chromium-containing solid waste in the form of shavings and trimmings. The recycling and reuse of those wastes must be the primary target in optimizing processes of the leather industry. The p...

  13. Drilling Waste Management Strategy for Field ‘X'

    OpenAIRE

    Wibowo, Risyad Ramadhan; Kasmungin, Sugiatmo; Rudiantoro, Agung Budi

    2015-01-01

    Drilling waste management is a planing and implementation of a prudent drilling waste collection,treatment and final disposal. A well planned drilling waste management system not only ensure thehealth and safety of the surrounding environment, it also brings advantages to the drilling operationeffectivity and economics. The drilling waste management technologies and practices can begrouped into three major categories : waste minimization, recylce/reuse and disposal. This essaywill later discu...

  14. Saponification pretreatment and solids recirculation as a new anaerobic process for the treatment of slaughterhouse waste.

    Science.gov (United States)

    Affes, R; Palatsi, J; Flotats, X; Carrère, H; Steyer, J P; Battimelli, A

    2013-03-01

    Different configurations of anaerobic process, adapted to the treatment of solid slaughterhouse fatty waste, were proposed and evaluated in this study. The tested configurations are based on the combination of anaerobic digestion with/without waste saponification pretreatment (70 °C during 60 min) and with/without recirculation of the digestate solid fraction (ratio=20% w/w). After an acclimation period of substrate pulses-feeding cycles, the reactors were operated in a semi-continuous feeding mode, increasing organic loading rates along experimental time. The degradation of the raw substrate was shown to be the bottleneck of the whole process, obtaining the best performance and process yields in the reactor equipped with waste pretreatment and solids recirculation. Saponification promoted the emulsification and bioavailability of solid fatty residues, while recirculation of solids minimized the substrate/biomass wash-out and induced microbial adaptation to the treatment of fatty substrates. Copyright © 2013 Elsevier Ltd. All rights reserved.

  15. Waste management

    DEFF Research Database (Denmark)

    Bruun Hansen, Karsten; Jamison, Andrew

    2000-01-01

    The case study deals with public accountability issues connected to household waste management in the municipality of Copenhagen, Denmark.......The case study deals with public accountability issues connected to household waste management in the municipality of Copenhagen, Denmark....

  16. Development of Bioelectrochemical Systems to Promote Sustainable Agriculture

    Directory of Open Access Journals (Sweden)

    Xiaojin Li

    2015-06-01

    Full Text Available Bioelectrochemical systems (BES are a newly emerged technology for energy-efficient water and wastewater treatment. Much effort as well as significant progress has been made in advancing this technology towards practical applications treating various types of waste. However, BES application for agriculture has not been well explored. Herein, studies of BES related to agriculture are reviewed and the potential applications of BES for promoting sustainable agriculture are discussed. BES may be applied to treat the waste/wastewater from agricultural production, minimizing contaminants, producing bioenergy, and recovering useful nutrients. BES can also be used to supply irrigation water via desalinating brackish water or producing reclaimed water from wastewater. The energy generated in BES can be used as a power source for wireless sensors monitoring the key parameters for agricultural activities. The importance of BES to sustainable agriculture should be recognized, and future development of this technology should identify proper application niches with technological advancement.

  17. Food waste

    OpenAIRE

    Arazim, Lukáš

    2015-01-01

    This thesis looks into issues related to food waste and consists of a theoretical and a practical part. Theoretical part aims to provide clear and complex definition of wood waste related problems, summarize current findings in Czech and foreign sources. Introduction chapter explains important terms and legal measures related to this topic. It is followed by description of causes, implications and possibilities in food waste reduction. Main goal of practical part is analyzing food waste in Cz...

  18. Bioremediation of cooking oil waste using lipases from wastes.

    Directory of Open Access Journals (Sweden)

    Clarissa Hamaio Okino-Delgado

    Full Text Available Cooking oil waste leads to well-known environmental impacts and its bioremediation by lipase-based enzymatic activity can minimize the high cytotoxic potential. In addition, they are among the biocatalysts most commercialized worldwide due to the versatility of reactions and substrates. However, although lipases are able to process cooking oil wastes, the products generated from this process do not necessarily become less toxic. Thus, the aim of the current study is to analyze the bioremediation of lipase-catalyzed cooking oil wastes, as well as their effect on the cytotoxicity of both the oil and its waste before and after enzymatic treatment. Thus, assessed the post-frying modification in soybean oil and in its waste, which was caused by hydrolysis reaction catalyzed by commercial and home-made lipases. The presence of lipases in the extracts obtained from orange wastes was identified by zymography. The profile of the fatty acid esters formed after these reactions was detected and quantified through gas chromatography and fatty acids profile compared through multivariate statistical analyses. Finally, the soybean oil and its waste, with and without enzymatic treatment, were assessed for toxicity in cytotoxicity assays conducted in vitro using fibroblast cell culture. The soybean oil wastes treated with core and frit lipases through transesterification reaction were less toxic than the untreated oils, thus confirming that cooking oil wastes can be bioremediated using orange lipases.

  19. Bioremediation of cooking oil waste using lipases from wastes

    Science.gov (United States)

    do Prado, Débora Zanoni; Facanali, Roselaine; Marques, Márcia Mayo Ortiz; Nascimento, Augusto Santana; Fernandes, Célio Junior da Costa; Zambuzzi, William Fernando

    2017-01-01

    Cooking oil waste leads to well-known environmental impacts and its bioremediation by lipase-based enzymatic activity can minimize the high cytotoxic potential. In addition, they are among the biocatalysts most commercialized worldwide due to the versatility of reactions and substrates. However, although lipases are able to process cooking oil wastes, the products generated from this process do not necessarily become less toxic. Thus, the aim of the current study is to analyze the bioremediation of lipase-catalyzed cooking oil wastes, as well as their effect on the cytotoxicity of both the oil and its waste before and after enzymatic treatment. Thus, assessed the post-frying modification in soybean oil and in its waste, which was caused by hydrolysis reaction catalyzed by commercial and home-made lipases. The presence of lipases in the extracts obtained from orange wastes was identified by zymography. The profile of the fatty acid esters formed after these reactions was detected and quantified through gas chromatography and fatty acids profile compared through multivariate statistical analyses. Finally, the soybean oil and its waste, with and without enzymatic treatment, were assessed for toxicity in cytotoxicity assays conducted in vitro using fibroblast cell culture. The soybean oil wastes treated with core and frit lipases through transesterification reaction were less toxic than the untreated oils, thus confirming that cooking oil wastes can be bioremediated using orange lipases. PMID:29073166

  20. Bioremediation of cooking oil waste using lipases from wastes.

    Science.gov (United States)

    Okino-Delgado, Clarissa Hamaio; Prado, Débora Zanoni do; Facanali, Roselaine; Marques, Márcia Mayo Ortiz; Nascimento, Augusto Santana; Fernandes, Célio Junior da Costa; Zambuzzi, William Fernando; Fleuri, Luciana Francisco

    2017-01-01

    Cooking oil waste leads to well-known environmental impacts and its bioremediation by lipase-based enzymatic activity can minimize the high cytotoxic potential. In addition, they are among the biocatalysts most commercialized worldwide due to the versatility of reactions and substrates. However, although lipases are able to process cooking oil wastes, the products generated from this process do not necessarily become less toxic. Thus, the aim of the current study is to analyze the bioremediation of lipase-catalyzed cooking oil wastes, as well as their effect on the cytotoxicity of both the oil and its waste before and after enzymatic treatment. Thus, assessed the post-frying modification in soybean oil and in its waste, which was caused by hydrolysis reaction catalyzed by commercial and home-made lipases. The presence of lipases in the extracts obtained from orange wastes was identified by zymography. The profile of the fatty acid esters formed after these reactions was detected and quantified through gas chromatography and fatty acids profile compared through multivariate statistical analyses. Finally, the soybean oil and its waste, with and without enzymatic treatment, were assessed for toxicity in cytotoxicity assays conducted in vitro using fibroblast cell culture. The soybean oil wastes treated with core and frit lipases through transesterification reaction were less toxic than the untreated oils, thus confirming that cooking oil wastes can be bioremediated using orange lipases.

  1. Automotive Wastes.

    Science.gov (United States)

    Guigard, Selma E; Shariaty, Pooya; Niknaddaf, Saeid; Lashaki, Masoud Jahandar; Atkinson, John D; Hashisho, Zaher

    2015-10-01

    A review of the literature from 2014 related to automotive wastes is presented. Topics include solid wastes from autobodies and tires as well as vehicle emissions to soil and air as a result of the use of conventional and alternative fuels. Potential toxicological and health risks related to automotive wastes are also discussed.

  2. Radioactive Waste.

    Science.gov (United States)

    Blaylock, B. G.

    1978-01-01

    Presents a literature review of radioactive waste disposal, covering publications of 1976-77. Some of the studies included are: (1) high-level and long-lived wastes, and (2) release and burial of low-level wastes. A list of 42 references is also presented. (HM)

  3. Microbial diversity of vermicompost bacteria that exhibit useful agricultural traits and waste management potential.

    Science.gov (United States)

    Pathma, Jayakumar; Sakthivel, Natarajan

    2012-01-01

    Vermicomposting is a non-thermophilic, boioxidative process that involves earthworms and associated microbes. This biological organic waste decomposition process yields the biofertilizer namely the vermicompost. Vermicompost is a finely divided, peat like material with high porosity, good aeration, drainage, water holding capacity, microbial activity, excellent nutrient status and buffering capacity thereby resulting the required physiochemical characters congenial for soil fertility and plant growth. Vermicompost enhances soil biodiversity by promoting the beneficial microbes which inturn enhances plant growth directly by production of plant growth-regulating hormones and enzymes and indirectly by controlling plant pathogens, nematodes and other pests, thereby enhancing plant health and minimizing the yield loss. Due to its innate biological, biochemical and physiochemical properties, vermicompost may be used to promote sustainable agriculture and also for the safe management of agricultural, industrial, domestic and hospital wastes which may otherwise pose serious threat to life and environment.

  4. The use of olive-mill waste compost to promote the plant vegetation cover in a trace-element-contaminated soil.

    Science.gov (United States)

    Pardo, Tania; Martínez-Fernández, Domingo; Clemente, Rafael; Walker, David J; Bernal, M Pilar

    2014-01-01

    The applicability of a mature compost as a soil amendment to promote the growth of native species for the phytorestoration of a mine-affected soil from a semi-arid area (SE Spain), contaminated with trace elements (As, Cd, Cu, Mn, Pb and Zn), was evaluated in a 2-year field experiment. The effects of an inorganic fertiliser were also determined for comparison. Bituminaria bituminosa was the selected native plant since it is a leguminous species adapted to the particular local pedoclimatic conditions. Compost addition increased total organic-C concentrations in soil with respect to the control and fertiliser treatments, maintained elevated available P concentrations throughout the duration of the experiment and stimulated soil microbial biomass, while trace elements extractability in the soil was rather low due to the calcareous nature of the soil and almost unaltered in the different treatments. Tissue concentrations of P and K in B. bituminosa increased after the addition of compost, associated with growth stimulation. Leaf Cu concentration was also increased by the amendments, although overall the trace elements concentrations can be considered non-toxic. In addition, the spontaneous colonisation of the plots by a total of 29 species of 15 different families at the end of the experiment produced a greater vegetation cover, especially in plots amended with compost. Therefore, the use of compost as a soil amendment appears to be useful for the promotion of a vegetation cover and the phytostabilisation of moderately contaminated soils under semi-arid conditions.

  5. Minimal Composite Inflation

    DEFF Research Database (Denmark)

    Channuie, Phongpichit; Jark Joergensen, Jakob; Sannino, Francesco

    2011-01-01

    We investigate models in which the inflaton emerges as a composite field of a four dimensional, strongly interacting and nonsupersymmetric gauge theory featuring purely fermionic matter. We show that it is possible to obtain successful inflation via non-minimal coupling to gravity, and that the u......We investigate models in which the inflaton emerges as a composite field of a four dimensional, strongly interacting and nonsupersymmetric gauge theory featuring purely fermionic matter. We show that it is possible to obtain successful inflation via non-minimal coupling to gravity......, and that the underlying dynamics is preferred to be near conformal. We discover that the compositeness scale of inflation is of the order of the grand unified energy scale....

  6. Minimally symmetric Higgs boson

    Energy Technology Data Exchange (ETDEWEB)

    Low, Ian

    2015-06-01

    Models addressing the naturalness of a light Higgs boson typically employ symmetries, either bosonic or fermionic, to stabilize the Higgs mass. We consider a setup with the minimal amount of symmetries: four shift symmetries acting on the four components of the Higgs doublet, subject to the constraints of linearly realized SU(2)(L) x U(1)(Y) electroweak symmetry. Up to terms that explicitly violate the shift symmetries, the effective Lagrangian can be derived, irrespective of the spontaneously broken group G in the ultraviolet, and is universal among all models where the Higgs arises as a pseudo-Nambu-Goldstone boson. Very high energy scatterings of vector bosons could provide smoking gun signals of a minimally symmetric Higgs boson.

  7. Passengers waste production during flights.

    Science.gov (United States)

    Tofalli, Niki; Loizia, Pantelitsa; Zorpas, Antonis A

    2017-12-20

    We assume that during flights the amount of waste that is produced is limited. However, daily, approximately 8000 commercial airplanes fly above Europe's airspace while at the same time, more than 17,000 commercial flights exist in the entire world. Using primary data from airlines, which use the Larnaca's International Airport (LIA) in Cyprus, we have tried to understand why wastes are produced during a typical flight such as food waste, paper, and plastics, as well as how passengers affect the production of those wastes. The compositional analysis took place on 27 flights of 4 different airlines which used LIA as final destination. The evaluation indicated that the passenger's habits and ethics, and the policy of each airline produced different kinds of waste during the flights and especially food waste (FW). Furthermore, it was observed that the only waste management strategy that exists in place in the airport is the collection and the transportation of all those wastes from aircrafts and from the airport in the central unit for further treatment. Hence, this research indicated extremely difficulties to implement any specific waste minimization, or prevention practice or other sorting methods during the flights due to the limited time of the most flights (less than 3 h), the limited available space within the aircrafts, and the strictly safety roles that exist during the flights.

  8. Influence of bioenergy waste biochar on proton- and ligand-promoted release of Pb and Cu in a shooting range soil.

    Science.gov (United States)

    Kumarathilaka, Prasanna; Ahmad, Mahtab; Herath, Indika; Mahatantila, Kushani; Athapattu, B C L; Rinklebe, Jörg; Ok, Yong Sik; Usman, Adel; Al-Wabel, Mohammad I; Abduljabbar, Adel; Vithanage, Meththika

    2017-12-29

    Presence of organic and inorganic acids influences the release rates of trace metals (TMs) bound in contaminated soil systems. This study aimed to investigate the influence of bioenergy waste biochar, derived from Gliricidia sepium (GBC), on the proton and ligand-induced bioavailability of Pb and Cu in a shooting range soil (17,066mg Pb and 1134mg Cu per kg soil) in the presence of inorganic (sulfuric, nitric, and hydrochloric) and organic acids (acetic, citric, and oxalic). Release rates of Pb and Cu in the shooting range soil were determined under different acid concentrations (0.05, 0.1, 0.5, 1, 5, and 10mM) and in the presence/absence of GBC (10% by weight of soil). The dissolution rates of Pb and Cu increased with increasing acid concentrations. Lead was preferentially released (2.79×10 -13 to 8.86×10 -13 molm -2 s -1 ) than Cu (1.07×10 -13 to 1.02×10 -13 molm -2 s -1 ) which could be due to the excessive Pb concentrations in soil. However, the addition of GBC to soil reduced Pb and Cu dissolution rates to a greater extent of 10.0 to 99.5% and 15.6 to 99.5%, respectively, under various acid concentrations. The increased pH in the medium and different adsorption mechanisms, including electrostatic attractions, surface diffusion, ion exchange, precipitation, and complexation could immobilize Pb and Cu released by the proton and ligands in GBC amended soil. Overall, GBC could be utilized as an effective soil amendment to immobilize Pb and Cu in shooting range soil even under the influence of soil acidity. Copyright © 2017. Published by Elsevier B.V.

  9. Combined Waste Form Cost Trade Study

    Energy Technology Data Exchange (ETDEWEB)

    Dirk Gombert; Steve Piet; Timothy Trickel; Joe Carter; John Vienna; Bill Ebert; Gretchen Matthern

    2008-11-01

    A new generation of aqueous nuclear fuel reprocessing, now in development under the auspices of the DOE Office of Nuclear Energy (NE), separates fuel into several fractions, thereby partitioning the wastes into groups of common chemistry. This technology advance enables development of waste management strategies that were not conceivable with simple PUREX reprocessing. Conventional wisdom suggests minimizing high level waste (HLW) volume is desirable, but logical extrapolation of this concept suggests that at some point the cost of reducing volume further will reach a point of diminishing return and may cease to be cost-effective. This report summarizes an evaluation considering three groupings of wastes in terms of cost-benefit for the reprocessing system. Internationally, the typical waste form for HLW from the PUREX process is borosilicate glass containing waste elements as oxides. Unfortunately several fission products (primarily Mo and the noble metals Ru, Rh, Pd) have limited solubility in glass, yielding relatively low waste loading, producing more glass, and greater disposal costs. Advanced separations allow matching the waste form to waste stream chemistry, allowing the disposal system to achieve more optimum waste loading with improved performance. Metals can be segregated from oxides and each can be stabilized in forms to minimize the HLW volume for repository disposal. Thus, a more efficient waste management system making the most effective use of advanced waste forms and disposal design for each waste is enabled by advanced separations and how the waste streams are combined. This trade-study was designed to juxtapose a combined waste form baseline waste treatment scheme with two options and to evaluate the cost-benefit using available data from the conceptual design studies supported by DOE-NE.

  10. Agricultural Waste.

    Science.gov (United States)

    Xue, Ling; Zhang, Panpan; Shu, Huajie; Chang, Chein-Chi; Wang, Renqing; Zhang, Shuping

    2016-10-01

    In recent years, the quantity of agricultural waste has been rising rapidly all over the world. As a result, the environmental problems and negative impacts of agricultural waste are drawn more and more attention. Therefore, there is a need to adopt proper approaches to reduce and reuse agricultural waste. This review presented about 200 literatures published in 2015 relating to the topic of agricultural waste. The review examined research on agricultural waste in 2015 from the following four aspects: the characterization, reuse, treatment, and management. Researchers highlighted the importance to reuse agricultural waste and investigated the potential to utilize it as biofertilizers, cultivation material, soil amendments, adsorbent, material, energy recycling, enzyme and catalyst etc. The treatment of agricultural waste included carbonization, biodegradation, composting hydrolysis and pyrolysis. Moreover, this review analyzed the differences of the research progress in 2015 from 2014. It may help to reveal the new findings and new trends in this field in 2015 comparing to 2014.

  11. Twelfth annual US DOE low-level waste management conference

    Energy Technology Data Exchange (ETDEWEB)

    1990-01-01

    The papers in this document comprise the proceedings of the Department of Energy's Twelfth Annual Low-Level Radioactive Waste Management Conference, which was held in Chicago, Illinois, on August 28 and 29, 1990. General subjects addressed during the conference included: mixed waste, low-level radioactive waste tracking and transportation, public involvement, performance assessment, waste stabilization, financial assurance, waste minimization, licensing and environmental documentation, below-regulatory-concern waste, low-level radioactive waste temporary storage, current challenges, and challenges beyond 1990.

  12. Biorremediation of soil polluted by 75000 ppm of waste motor oil applying biostimulation and phytoremediation with Sorghum vulgare and Bacillus cereus or Burkholderia cepacia

    OpenAIRE

    Balderas-León Iván; Sánchez-Yáñez Juan Manuel

    2015-01-01

    Waste motor oil (WMO) pollutes soil and causing lost soil fertility. An alternative to solve this problem its bioremediation (BR) by double and following biostimulation (BS) with mineral solution (MS) and a legume as green manure (GM) then using phytoremediation (PR) with growth promoting vegetal bacteria (GPVB) like Bacillus cereus and Burkholderia cepacia to minimize remaining WMO. The aims of this research were: a) bioremediation of polluted soil by 75000 ppm of WMO by biostimulation and t...

  13. Minimally Invasive Parathyroidectomy

    Directory of Open Access Journals (Sweden)

    Lee F. Starker

    2011-01-01

    Full Text Available Minimally invasive parathyroidectomy (MIP is an operative approach for the treatment of primary hyperparathyroidism (pHPT. Currently, routine use of improved preoperative localization studies, cervical block anesthesia in the conscious patient, and intraoperative parathyroid hormone analyses aid in guiding surgical therapy. MIP requires less surgical dissection causing decreased trauma to tissues, can be performed safely in the ambulatory setting, and is at least as effective as standard cervical exploration. This paper reviews advances in preoperative localization, anesthetic techniques, and intraoperative management of patients undergoing MIP for the treatment of pHPT.

  14. Minimally Actuated Serial Robot

    OpenAIRE

    Mann, Moshe P.; Damti, Lior; Zarrouk, David

    2017-01-01

    In this paper, we propose a novel type of serial robot with minimal actuation. The robot is a serial rigid structure consisting of multiple links connected by passive joints and of movable actuators. The novelty of this robot is that the actuators travel over the links to a given joint and adjust the relative angle between the two adjacent links. The joints passively preserve their angles until one of the actuators moves them again. This actuation can be applied to any serial robot with two o...

  15. The challenges of municipal solid waste management systems provided by public-private partnerships in mature tourist destinations: The case of Mallorca.

    Science.gov (United States)

    Arbulú, Italo; Lozano, Javier; Rey-Maquieira, Javier

    2016-05-01

    This article analyzes the influence of tourism on the municipal solid waste management (MSWM) system taking as reference the case study of Mallorca, an internationally renowned destination. The characteristics of tourism such as seasonality and land scarcity, set interesting challenges to public-private partnerships related to MSWM system. The analysis of Mallorca's experience shows that land endowment strongly influences the choice of treatment technologies in tourism destinations. Furthermore, tourism seasonality significantly affects management costs which should be considered on PPP contracts. Finally, the tariff system in this kind of environmental PPPs in tourist destinations still need to improve to promote waste minimization and recycling. Copyright © 2016 Elsevier Ltd. All rights reserved.

  16. Waste Bank Revitalization in Palabuhanratu West Java

    Science.gov (United States)

    Samadikun, Budi Prasetyo; Handayani, Dwi Siwi; Laksana, Muhamad Permana

    2018-02-01

    Palabuhanratu Village has three waste banks, one of them was established since 2010, the others built in 2016. However, waste processing from the source is still not optimal, it's only reduced waste about 5% of the total waste generated to the final waste disposal site. The performance of waste banks is still minimal, because one waste bank can not serve the entire area of the village. Furthermore, organic waste processed by some communities of Palabuhanratu Village to be compost can not be a mass movement, due to the lack of public knowledge. The purpose of this research is to know the existing condition of waste management in Palabuhanratu Village and to formulate the revitalization of existing waste bank. The research used survey research method by using questionnaire, in depth interview, and observation. Analytical technique using quantitative and qualitative analysis. The findings of the research indicate that the residents of Palabuhanratu Village who often do waste sorting from the source only from the residents of RT 01 / RW 33. The number of existing temporary waste disposal site in Palabuhanratu Village is still lacking, so it requires addition up to 5 units that integrated with waste bank in this village.

  17. WASTE MINIZATION OPPORTUNITY ASSESSMENT: A CLASS 8 TRUCK ASSEMBLY PLANT

    Science.gov (United States)

    EPA has developed a systematic approach to identify and implement options to reduce or eliminate hazardous waste. he approach is presented in a report entitled, "Waste Minimization Opportunity Assessment Manual" (EPA/625/7-88/O03). his report describes the application of the wast...

  18. Assessment of a Planned Municipal Solid Waste Management ...

    African Journals Online (AJOL)

    The ongoing MSWM practices of Balangoda Urban Council encompass six categories as waste minimization and handling; waste collection; on-site separation; waste transportation; further management including grading, composting, recycling, producing sludge fertilizer; and final disposal to an open dump site. Apart from ...

  19. Waste management in paint industries in Pakistan | Nawaz | Journal ...

    African Journals Online (AJOL)

    Chemical analyses of wastes in paint production and application have been carried out with the objective of minimizing production losses and ensuring waste management through integrated process design. The wastes contained high concentration of heavy metals, volatile organic compounds, dissolved solids and the ...

  20. Report on the survey in fiscal 1998. Basic survey on promotion of the joint implementation (a survey on improvement in wastes treatment system in Tapioka starch manufacturing plants); 1998 nendo chosa hokokusho. Kyodo jisshi nado suishin kiso chosa (Tapioka denpun kako kojo no haikibutsu shori no kaizen chosa)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    In order to promote the joint implementation based on COP3, a survey and a discussion were given on improvement in wastes treatment systems and reduction of greenhouse effect gas emission in Tapioka starch manufacturing plants scattered in Indonesia. Currently, the wastes are disposed untreated, discharging methane gas into atmosphere as a result of putrefaction and contamination. Ten factories were picked up as the object of the survey. The following processes are to be adopted as the most suitable method for treating waste water and waste substances: solids (peels and fibers) are composted, and rinsing waste water is subjected to simple aerobic treatment; purified waste water is recovered of methane gas by means of anaerobic treatment; and the reduction amount of greenhouse effect gas converted to CO2 is estimated to reach 314,824 tons per year in total of the ten factories. If the carbon dioxide discharge right can be transacted at a sales price of a dollar per ton, assuming the compost sales price at 200 Rp./kg, the IRR will be 10% or higher, making the project very highly profitable. An IRR of 8% may not be assured unless the discharge right can be sold at 5 dollars per ton if the compost sales price is 150 Rp./kg. The Indonesian Government expects financial assistance from Japan for the pilot plant demonstration. (NEDO)

  1. A multimodal transportation system routing implemented in waste collection

    Directory of Open Access Journals (Sweden)

    Masoud Rabbani

    2016-01-01

    Full Text Available Waste collection is an important municipal service that charges large expenditures to waste management (WM system. In this study, a hierarchical structure is proposed in order to minimize total cost of waste collection routing problem. Moreover, in second stage destructive environmental effects of waste transportation are minimized concurrently through taking advantage of a road/rail transportation system. In the proposed multimodal transportation system, waste packs are transferred to final destination while travel time and risk of environmental threatening is minimized. The discussed problem is formulated mathematically in two stages. In the first stage, a household waste collection routing problem is formulated while, in second stage a multimodal transportation system is routed to transfer waste packs to final destination through roads and railroads. In order to solve the proposed NP hard models, an improved genetic algorithm is developed. Comparison of the obtained results with those of GAMS for small-size samples validates the proposed models.

  2. Industrial Waste

    DEFF Research Database (Denmark)

    Christensen, Thomas Højlund

    2011-01-01

    Industrial waste is waste from industrial production and manufacturing. Industry covers many industrial sectors and within each sector large variations are found in terms of which raw materials are used, which production technology is used and which products are produced. Available data on unit...... generation rates and material composition as well as determining factors are discussed in this chapter. Characterizing industrial waste is faced with the problem that often only a part of the waste is handled in the municipal waste system, where information is easily accessible. In addition part...... of the industrial waste may in periods, depending on market opportunities and prices, be traded as secondary rawmaterials. Production-specificwaste from primary production, for example steel slag, is not included in the current presentation. In some countries industries must be approved or licensed and as part...

  3. The reduction of packaging waste

    Energy Technology Data Exchange (ETDEWEB)

    Raney, E.A.; Hogan, J.J.; McCollom, M.L.; Meyer, R.J.

    1994-04-01

    Nationwide, packaging waste comprises approximately one-third of the waste disposed in sanitary landfills. the US Department of Energy (DOE) generated close to 90,000 metric tons of sanitary waste. With roughly one-third of that being packaging waste, approximately 30,000 metric tons are generated per year. The purpose of the Reduction of Packaging Waste project was to investigate opportunities to reduce this packaging waste through source reduction and recycling. The project was divided into three areas: procurement, onsite packaging and distribution, and recycling. Waste minimization opportunities were identified and investigated within each area, several of which were chosen for further study and small-scale testing at the Hanford Site. Test results, were compiled into five ``how-to`` recipes for implementation at other sites. The subject of the recipes are as follows: (1) Vendor Participation Program; (2) Reusable Containers System; (3) Shrink-wrap System -- Plastic and Corrugated Cardboard Waste Reduction; (4) Cardboard Recycling ; and (5) Wood Recycling.

  4. Waste indicators

    Energy Technology Data Exchange (ETDEWEB)

    Dall, O.; Lassen, C.; Hansen, E. [Cowi A/S, Lyngby (Denmark)

    2003-07-01

    The Waste Indicator Project focuses on methods to evaluate the efficiency of waste management. The project proposes the use of three indicators for resource consumption, primary energy and landfill requirements, based on the life-cycle principles applied in the EDIP Project. Trial runs are made With the indicators on paper, glass packaging and aluminium, and two models are identified for mapping the Danish waste management, of which the least extensive focuses on real and potential savings. (au)

  5. Selective Hydrogenolysis of Glycerol and Crude Glycerol (a By-Product or Waste Stream from the Biodiesel Industry to 1,2-Propanediol over B2O3 Promoted Cu/Al2O3 Catalysts

    Directory of Open Access Journals (Sweden)

    Malaya R. Nanda

    2017-06-01

    Full Text Available The performance of boron oxide (B2O3-promoted Cu/Al2O3 catalyst in the selective hydrogenolysis of glycerol and crude glycerol (a by-product or waste stream from the biodiesel industry to produce 1,2-propanediol (1,2-PDO was investigated. The catalysts were characterized using N2-adsorption-desorption isotherm, Inductively coupled plasma atomic emission spectroscopy (ICP-AES, X-ray diffraction (XRD, ammonia temperature programmed desorption (NH3-TPD, thermogravimetric analysis (TGA, temperature programmed reduction (TPR, and transmission electron microscopy (TEM. Incorporation of B2O3 to Cu/Al2O3 was found to enhance the catalytic activity. At the optimum condition (250 °C, 6 MPa H2 pressure, 0.1 h−1 WHSV (weight hourly space velocity, and 5Cu-B/Al2O3 catalyst, 10 wt% aqueous solution of glycerol was converted into 1,2-PDO at 98 ± 2% glycerol conversion and 98 ± 2% selectivity. The effects of temperature, pressure, boron addition amount, and liquid hourly space velocity were studied. Different grades of glycerol (pharmaceutical, technical, or crude glycerol were used in the process to investigate the stability and resistance to deactivation of the selected 5Cu-B/Al2O3 catalyst.

  6. A novel hybrid total variation minimization algorithm for compressed sensing

    Science.gov (United States)

    Li, Hongyu; Wang, Yong; Liang, Dong; Ying, Leslie

    2017-05-01

    Compressed sensing (CS) is a technology to acquire and reconstruct sparse signals below the Nyquist rate. For images, total variation of the signal is usually minimized to promote sparseness of the image in gradient. However, similar to all L1-minimization algorithms, total variation has the issue of penalizing large gradient, thus causing large errors on image edges. Many non-convex penalties have been proposed to address the issue of L1 minimization. For example, homotopic L0 minimization algorithms have shown success in reconstructing images from magnetic resonance imaging (MRI). Homotopic L0 minimization may suffer from local minimum which may not be sufficiently robust when the signal is not strictly sparse or the measurements are contaminated by noise. In this paper, we propose a hybrid total variation minimization algorithm to integrate the benefits of both L1 and homotopic L0 minimization algorithms for image recovery from reduced measurements. The algorithm minimizes the conventional total variation when the gradient is small, and minimizes the L0 of gradient when the gradient is large. The transition between L1 and L0 of the gradients is determined by an auto-adaptive threshold. The proposed algorithm has the benefits of L1 minimization being robust to noise/approximation errors, and also the benefits of L0 minimization requiring fewer measurements for recovery. Experimental results using MRI data are presented to demonstrate the proposed hybrid total variation minimization algorithm yields improved image quality over other existing methods in terms of the reconstruction accuracy.

  7. Waste management/waste certification plan for the Oak Ridge National Laboratory Environmental Restoration Program

    Energy Technology Data Exchange (ETDEWEB)

    Clark, C. Jr.; Hunt-Davenport, L.D.; Cofer, G.H.

    1995-03-01

    This Waste Management/Waste Certification (C) Plan, written for the Environmental Restoration (ER) Program at Oak Ridge National Laboratory (ORNL), outlines the criteria and methodologies to be used in the management of waste generated during ORNL ER field activities. Other agreed upon methods may be used in the management of waste with consultation with ER and Waste Management Organization. The intent of this plan is to provide information for the minimization, handling, and disposal of waste generated by ER activities. This plan contains provisions for the safe and effective management of waste consistent with the U.S. Environmental Protection Agency`s (EPA`s) guidance. Components of this plan have been designed to protect the environment and the health and safety of workers and the public. It, therefore, stresses that investigation derived waste (IDW) and other waste be managed to ensure that (1) all efforts be made to minimize the amount of waste generated; (2) costs associated with sampling storage, analysis, transportation, and disposal are minimized; (3) the potential for public and worker exposure is not increased; and (4) additional contaminated areas are not created.

  8. Material Recycling and Waste Minimization by Freeze Crystallization. Phase 1

    Science.gov (United States)

    1995-05-01

    Precautions - Ventilation: the refrigeration sources generate gas that can cause suffocation , and thus should be used only in a well ventilated area. - The...an ice wash column, with an electric heater in the repulp slurry line to melt the ice as it is purified and scraped off the top of the column. a salt...after the heater at a few degrees above the normal melting temperature of pure ice. The levels in reslurry chambers are periodically lowered by pumping

  9. 2.75-Inch Motor Manufacturing Waste Minimization Project

    Science.gov (United States)

    2006-06-19

    Institute of Technology vii LIST OF ACRONYMS—Continued SMAW Shoulder-Launched Multipurpose Assault Weapon SRM Shear roll mill TACOM Tank-Automotive...caliber ammunition, tank rounds (tactical and training), rocket motors (TOW Launch, Hydra 70, and SMAW ), and specialty applications. New River

  10. Hazardous Waste Minimization Initiation Decision Report. Volume 2. Appendixes.

    Science.gov (United States)

    1988-06-01

    The oxidation of aLrazine, butyl phthalate , chloroaniline, diphenyl hydrazine, ethylene dibromide, malathion, pentachlorophenol, and xylene was rapid...microorganisms in the presence of oxygen. The hydraulic detention time of this unit operation is usually from 6 to 24 hr. Depending upon the process mode...shorter or longer detention times may be achieved. This is followed by a sludge-liquid separation step in a clarifier. Organic loading rates can vary

  11. Technology Assessment of Selected Hazardous Waste Minimization Process Changes

    Science.gov (United States)

    1988-03-01

    compounds produces dermatitic skin lesions, and ulceration and perforation of the nasal septum, as well as liver and kidney damage. Incidence of lung...sorts are produced, as well as ozone from the reaction of atmospheric oxygen and ultraviolet radiation from the plasma arc. Other gases may be present

  12. AmBe Waste Minimization Activities Annual Report

    Energy Technology Data Exchange (ETDEWEB)

    Kent D. Abney; Zita V. Svitra; Michael R. Cisneros

    1999-05-01

    The CST-11 objective for the Radioactive Source Recovery Project is to evaluate a nitric acid-based flowsheet and alternatives for dissolution, separation, and recovery of americium from AmBe neutron source materials returned from private and governmental institutions. Specific tasks performed during FY97 and FY98 included the experimental investigation of material dissolution rate and efficiency as a function of time and temperature for nitric acid as compared to hydrochloric acid. Alkaline dissolution reaction conditions using sodium hydroxide and ammonium bifluoride were also investigated. In both the acidic and alkaline dissolution conditions, the objective was to effect an initial separation of the americium from the beryllium or vice versa. The process solution and remaining solids should also be amenable to further processing and purification schemes. This work was performed on actual AmBe neutron source material in order to demonstrate the feasibility of {sup 241}Am purification from dismantled neutron sources.

  13. Addressing food waste reduction in Denmark

    DEFF Research Database (Denmark)

    Halloran, Afton Marina Szasz; Clement, Jesper; Kornum, Niels

    2014-01-01

    . In order to better understand food waste and loss more research must be conducted on the total amount of food waste at every level of the food supply chain. Solutions can be found through improved communication, more efficient food packaging, and better in interpretation of food labels by consumers......Global food demand is driven by population and economic growth, and urbanization. One important instrument to meet this increasing demand and to decrease the pressure on food production is to minimize food losses and food waste. Food waste and loss is a major societal, economic, nutritional...... and environmental challenge. Using the case of Denmark, this paper analyses causes of food waste, and discusses how different stakeholders address the prevention and reuse of the €1.18. billion of annual edible food waste. Currently, the majority of food waste is still incinerated with energy recovery. However...

  14. Transanal Minimally Invasive Surgery

    Science.gov (United States)

    deBeche-Adams, Teresa; Nassif, George

    2015-01-01

    Transanal minimally invasive surgery (TAMIS) was first described in 2010 as a crossover between single-incision laparoscopic surgery and transanal endoscopic microsurgery (TEM) to allow access to the proximal and mid-rectum for resection of benign and early-stage malignant rectal lesions. The TAMIS technique can also be used for noncurative intent surgery of more advanced lesions in patients who are not candidates for radical surgery. Proper workup and staging should be done before surgical decision-making. In addition to the TAMIS port, instrumentation and set up include readily available equipment found in most operating suites. TAMIS has proven its usefulness in a wide range of applications outside of local excision, including repair of rectourethral fistula, removal of rectal foreign body, control of rectal hemorrhage, and as an adjunct in total mesorectal excision for rectal cancer. TAMIS is an easily accessible, technically feasible, and cost-effective alternative to TEM. PMID:26491410

  15. Minimal asymmetric dark matter

    Directory of Open Access Journals (Sweden)

    Sofiane M. Boucenna

    2015-09-01

    Full Text Available In the early Universe, any particle carrying a conserved quantum number and in chemical equilibrium with the thermal bath will unavoidably inherit a particle–antiparticle asymmetry. A new particle of this type, if stable, would represent a candidate for asymmetric dark matter (DM with an asymmetry directly related to the baryon asymmetry. We study this possibility for a minimal DM sector constituted by just one (generic SU(2L multiplet χ carrying hypercharge, assuming that at temperatures above the electroweak phase transition an effective operator enforces chemical equilibrium between χ and the Higgs boson. We argue that limits from DM direct detection searches severely constrain this scenario, leaving as the only possibilities scalar or fermion multiplets with hypercharge y=1, preferentially quintuplets or larger SU(2 representations, and with a mass in the few TeV range.

  16. Minimally extended SILH

    Energy Technology Data Exchange (ETDEWEB)

    Chala, Mikael [Deutsches Elektronen-Synchrotron (DESY), Hamburg (Germany); Valencia Univ. (Spain). Dept. de Fisica Teorica y IFIC; Durieux, Gauthier; Matsedonskyi, Oleksii [Deutsches Elektronen-Synchrotron (DESY), Hamburg (Germany); Grojean, Christophe [Deutsches Elektronen-Synchrotron (DESY), Hamburg (Germany); Humboldt-Univ. Berlin (Germany). Inst. fuer Physik; Lima, Leonardo de [Deutsches Elektronen-Synchrotron (DESY), Hamburg (Germany); Univ. Estadual Paulista, Sao Paulo (Brazil). Inst. de Fisica Teorica

    2017-03-15

    Higgs boson compositeness is a phenomenologically viable scenario addressing the hierarchy problem. In minimal models, the Higgs boson is the only degree of freedom of the strong sector below the strong interaction scale. We present here the simplest extension of such a framework with an additional composite spin-zero singlet. To this end, we adopt an effective field theory approach and develop a set of rules to estimate the size of the various operator coefficients, relating them to the parameters of the strong sector and its structural features. As a result, we obtain the patterns of new interactions affecting both the new singlet and the Higgs boson's physics. We identify the characteristics of the singlet field which cause its effects on Higgs physics to dominate over the ones inherited from the composite nature of the Higgs boson. Our effective field theory construction is supported by comparisons with explicit UV models.

  17. Minimal Reducts with Grasp

    Directory of Open Access Journals (Sweden)

    Iris Iddaly Mendez Gurrola

    2011-03-01

    Full Text Available The proper detection of patient level of dementia is important to offer the suitable treatment. The diagnosis is based on certain criteria, reflected in the clinical examinations. From these examinations emerge the limitations and the degree in which each patient is in. In order to reduce the total of limitations to be evaluated, we used the rough set theory, this theory has been applied in areas of the artificial intelligence such as decision analysis, expert systems, knowledge discovery, classification with multiple attributes. In our case this theory is applied to find the minimal limitations set or reduct that generate the same classification that considering all the limitations, to fulfill this purpose we development an algorithm GRASP (Greedy Randomized Adaptive Search Procedure.

  18. Natural minimal dark matter

    CERN Document Server

    Fabbrichesi, Marco

    2016-01-01

    We show how the Higgs boson mass is protected from the potentially large corrections due to the introduction of minimal dark matter if the new physics sector is made supersymmetric. The fermionic dark matter candidate (a 5-plet of $SU(2)_L$) is accompanied by a scalar state. The weak gauge sector is made supersymmetric and the Higgs boson is embedded in a supersymmetric multiplet. The remaining standard model states are non-supersymmetric. Non vanishing corrections to the Higgs boson mass only appear at three-loop level and the model is natural for dark matter masses up to 15 TeV--a value larger than the one required by the cosmological relic density. The construction presented stands as an example of a general approach to naturalness that solves the little hierarchy problem which arises when new physics is added beyond the standard model at an energy scale around 10 TeV.

  19. A consumption approach to wastes from economic activities.

    Science.gov (United States)

    Beylot, Antoine; Boitier, Baptiste; Lancesseur, Nicolas; Villeneuve, Jacques

    2016-03-01

    In a context of waste management policies aimed at promoting waste prevention and recycling and, conversely, reducing waste landfilling, this study investigates how waste is generated and treated in a consumption perspective. A Waste Input-Output Analysis is implemented that considers 14 waste fractions and four waste management techniques. Input-Output Tables extended to wastes are initially compiled for the year 2008 considering France and five of its main import suppliers, and further completed with data on waste treatment. Wastes from economic activities are accordingly reallocated to the product categories of household consumption that induce their production. In particular, considering five waste categories (dry recyclable wastes, mixed wastes, mineral wastes, organic wastes, and total wastes) as an aggregation of the 14 waste fractions studied, the ten product categories with the highest contribution account for 64-86% of the total generation of wastes. Waste intensity and volume of expenses are analyzed as the drivers for the amounts of wastes induced by each product category. Similarly, the products responsible for the largest amounts of waste landfilling and incineration without energy recovery, i.e. the management techniques at the bottom of the "waste management hierarchy", are identified. Moreover, this study highlights the relative importance of waste produced abroad as compared to that produced in France, regarding the total amount of waste induced by French household consumption. The sensitivity of results to the modeling of import production is subsequently discussed. Finally, the potential perspectives for this type of consumption approach are considered with respect to its utility and current limitations in a context of waste policy planning, and more particularly regarding the way waste policy targets are set. Copyright © 2016 Elsevier Ltd. All rights reserved.

  20. USBI Booster Production Company's Hazardous Waste Management Program at the Kennedy Space Center, FL

    Science.gov (United States)

    Venuto, Charles

    1987-01-01

    In response to the hazardous-waste generating processes associated with the launch of the Space Shuttle, a hazardous waste management plan has been developed. It includes waste recycling, product substitution, waste treatment, and waste minimization at the source. Waste material resulting from the preparation of the nonmotor segments of the solid rocket boosters include waste paints (primer, topcoats), waste solvents (methylene chloride, freon, acetone, toluene), waste inorganic compounds (aluminum anodizing compound, fixer), and others. Ways in which these materials are contended with at the Kennedy Space Center are discussed.

  1. SOLID WASTE MANAGEMENT IN TABRIZ PETROCHEMICAL COMPLEX

    Directory of Open Access Journals (Sweden)

    M. A. Abduli, M. Abbasi, T. Nasrabadi, H. Hoveidi, N. Razmkhah

    2006-07-01

    Full Text Available Tabriz petrochemical complex is located in the northwest of Iran. Major products of this industry include raw plastics like, polyethylene, polystyrene, acrylonitrile, butadiene, styrene, etc. Sources of waste generation include service units, health and cure units, water, power, steam and industrial processes units. In this study, different types of solid waste including hazardous and non hazardous solid wastes were investigated separately. The aim of the study was to focus on the management of the industrial wastes in order to minimize the adverse environmental impacts. In the first stage, locating map and dispersion limits were prepared. Then, the types and amounts of industrial waste generated in were evaluated by an inventory and inspection. Wastes were classified according to Environmental Protection Agency and Basel Standards and subsequently hazards of different types were investigated. The waste management of TPC is quite complex because of the different types of waste and their pollution. In some cases recycling/reuse of waste is the best option, but treatment and disposal are also necessary tools. In this study, using different sources and references, generally petrochemical sources, various solid waste management practices were investigated and the best options were selected. Some wastes should be treated before land filling and some of them should be reused or recycled. In the case of solid waste optimization, source reduction ways were recommended as well as prior incineration system was modified.

  2. Stock flow diagram analysis on solid waste management in Malaysia

    Science.gov (United States)

    Zulkipli, Faridah; Nopiah, Zulkifli Mohd; Basri, Noor Ezlin Ahmad; Kie, Cheng Jack

    2016-10-01

    The effectiveness on solid waste management is a major importance to societies. Numerous generation of solid waste from our daily activities has risked for our communities. These due to rapid population grow and advance in economic development. Moreover, the complexity of solid waste management is inherently involved large scale, diverse and element of uncertainties that must assist stakeholders with deviating objectives. In this paper, we proposed a system dynamics simulation by developing a stock flow diagram to illustrate the solid waste generation process and waste recycle process. The analysis highlights the impact on increasing the number of population toward the amount of solid waste generated and the amount of recycled waste. The results show an increment in the number of population as well as the amount of recycled waste will decrease the amount of waste generated. It is positively represent the achievement of government aim to minimize the amount of waste to be disposed by year 2020.

  3. e-Waste Management Scenarios in Malaysia

    Directory of Open Access Journals (Sweden)

    Fatihah Suja

    2014-01-01

    Full Text Available e-Waste, or electronic waste, disposal that is uncontrolled can be harmful to human health and the environment because e-waste contains toxic substances and heavy metals. However, if the waste is properly managed, it can become a business opportunity that produces high returns because e-waste also contains valuable materials, such as gold, silver, platinum, and palladium. The government of Malaysia wants to ensure the safe, effective, and economically beneficial management of e-waste in Malaysia. Management approaches have included law enforcement and regulation and the promotion of e-waste recovery activities. e-Waste of no commercial value must be disposed of at sites/premises licensed by the Department of Environment (DOE, Malaysia. To date, 18 full recovery facilities and 128 partial recovery facilities that use various available technologies have been designated for the segregation, dismantling, and treatment of e-waste. However, there are issues faced by the recovery facilities in achieving the goal of converting e-waste into a source material. The issues include the e-waste supply, the importation of e-waste derived products and coding, and finally the need to develop the criteria for e-waste processing technologies to ensure the safety and the sustainability of the facilities.

  4. Swarm robotics and minimalism

    Science.gov (United States)

    Sharkey, Amanda J. C.

    2007-09-01

    Swarm Robotics (SR) is closely related to Swarm Intelligence, and both were initially inspired by studies of social insects. Their guiding principles are based on their biological inspiration and take the form of an emphasis on decentralized local control and communication. Earlier studies went a step further in emphasizing the use of simple reactive robots that only communicate indirectly through the environment. More recently SR studies have moved beyond these constraints to explore the use of non-reactive robots that communicate directly, and that can learn and represent their environment. There is no clear agreement in the literature about how far such extensions of the original principles could go. Should there be any limitations on the individual abilities of the robots used in SR studies? Should knowledge of the capabilities of social insects lead to constraints on the capabilities of individual robots in SR studies? There is a lack of explicit discussion of such questions, and researchers have adopted a variety of constraints for a variety of reasons. A simple taxonomy of swarm robotics is presented here with the aim of addressing and clarifying these questions. The taxonomy distinguishes subareas of SR based on the emphases and justifications for minimalism and individual simplicity.

  5. Minimal dilaton model

    Directory of Open Access Journals (Sweden)

    Oda Kin-ya

    2013-05-01

    Full Text Available Both the ATLAS and CMS experiments at the LHC have reported the observation of the particle of mass around 125 GeV which is consistent to the Standard Model (SM Higgs boson, but with an excess of events beyond the SM expectation in the diphoton decay channel at each of them. There still remains room for a logical possibility that we are not seeing the SM Higgs but something else. Here we introduce the minimal dilaton model in which the LHC signals are explained by an extra singlet scalar of the mass around 125 GeV that slightly mixes with the SM Higgs heavier than 600 GeV. When this scalar has a vacuum expectation value well beyond the electroweak scale, it can be identified as a linearly realized version of a dilaton field. Though the current experimental constraints from the Higgs search disfavors such a region, the singlet scalar model itself still provides a viable alternative to the SM Higgs in interpreting its search results.

  6. Minimal Higgs inflation

    Directory of Open Access Journals (Sweden)

    Debaprasad Maity

    2017-06-01

    Full Text Available In this paper we propose minimal Higgs inflation scenarios by non-polynomial modification of the Higgs potential. The modification is done in such a way that it creates a flat plateau for a huge range of field values at the inflationary energy scale μ≃(λ1/4α. Assuming the perturbative Higgs quartic coupling, λ≃O(1, our model prediction for all the cosmologically relevant quantities, (ns,r,dnsk, fit extremely well with observations made by PLANCK. For both the models the inflation energy scale turned out to be μ≃(1014,1015 GeV. Considering observed central value of the scalar spectral index, ns=0.968, models predict efolding number, N=(52,47. Within a wide range of viable parameter space, we found that the prediction of tensor to scalar ratio r(≤10−5 is far below the current experimental limit. The prediction for the running of scalar spectral index, dnsk, remains very small. We also computed the background field dependent unitarity scale Λ(h, which turned out to be much larger than the aforementioned inflationary energy scale.

  7. Assessing farmers' practices on disposal of pesticide waste after use.

    Science.gov (United States)

    Damalas, Christos A; Telidis, Georgios K; Thanos, Stavros D

    2008-02-15

    Common practices of farmers on disposal of pesticide waste after use were surveyed in five regions of the rural area of Pieria in northern Greece using a structured questionnaire administered via personal interviews. Concerning leftover spray solutions, most farmers reported that they normally re-spray the treated field area until the spraying tank is empty (54.9%) or they apply the leftover spray solutions to another crop listed on the product label (30.2%). A minority of the farmers (4.3%) mentioned that they often release the leftover spray solutions near or into irrigation canals and streams. As regards rinsates generated from washing the application equipment, most farmers reported that they release the rinsates over a non-cropped area (45.7%) or they drop the rinsates near or into irrigation canals and streams (40.7%). Moreover, a great proportion of the farmers stated that they dump the empty containers by the field (30.2%) or they throw them near or into irrigation canals and streams (33.3%). Burning the empty containers in open fire (17.9%) or throwing the empty containers in common waste places (11.1%) was also reported. Several farmers stated that they continue to use old pesticides for spraying (35.8%). Training programs which raise awareness of farmers of the potential hazards of pesticide use and particularly of the proper management of waste products, recycling programs and collection systems for unwanted agricultural chemicals to prevent inappropriate waste disposal, as well as improving packaging of pesticides to minimize waste production are essential for promoting safety during all phases of pesticide handling.

  8. Surrogate formulations for thermal treatment of low-level mixed waste, Part II: Selected mixed waste treatment project waste streams

    Energy Technology Data Exchange (ETDEWEB)

    Bostick, W.D.; Hoffmann, D.P.; Chiang, J.M.; Hermes, W.H.; Gibson, L.V. Jr.; Richmond, A.A. [Martin Marietta Energy Systems, Inc., Oak Ridge, TN (United States); Mayberry, J. [Science Applications International Corp., Idaho Falls, ID (United States); Frazier, G. [Univ. of Tennessee, Knoxville, TN (United States)

    1994-01-01

    This report summarizes the formulation of surrogate waste packages, representing the major bulk constituent compositions for 12 waste stream classifications selected by the US DOE Mixed Waste Treatment Program. These waste groupings include: neutral aqueous wastes; aqueous halogenated organic liquids; ash; high organic content sludges; adsorbed aqueous and organic liquids; cement sludges, ashes, and solids; chloride; sulfate, and nitrate salts; organic matrix solids; heterogeneous debris; bulk combustibles; lab packs; and lead shapes. Insofar as possible, formulation of surrogate waste packages are referenced to authentic wastes in inventory within the DOE; however, the surrogate waste packages are intended to represent generic treatability group compositions. The intent is to specify a nonradiological synthetic mixture, with a minimal number of readily available components, that can be used to represent the significant challenges anticipated for treatment of the specified waste class. Performance testing and evaluation with use of a consistent series of surrogate wastes will provide a means for the initial assessment (and intercomparability) of candidate treatment technology applicability and performance. Originally the surrogate wastes were intended for use with emerging thermal treatment systems, but use may be extended to select nonthermal systems as well.

  9. Food waste and the food-energy-water nexus: A review of food waste management alternatives.

    Science.gov (United States)

    Kibler, Kelly M; Reinhart, Debra; Hawkins, Christopher; Motlagh, Amir Mohaghegh; Wright, James

    2018-01-20

    Throughout the world, much food produced is wasted. The resource impact of producing wasted food is substantial; however, little is known about the energy and water consumed in managing food waste after it has been disposed. Herein, we characterize food waste within the Food-Energy-Water (FEW) nexus and parse the differential FEW effects of producing uneaten food and managing food loss and waste. We find that various food waste management options, such as waste prevention, landfilling, composting, anaerobic digestion, and incineration, present variable pathways for FEW impacts and opportunities. Furthermore, comprehensive sustainable management of food waste will involve varied mechanisms and actors at multiple levels of governance and at the level of individual consumers. To address the complex food waste problem, we therefore propose a "food-waste-systems" approach to optimize resources within the FEW nexus. Such a framework may be applied to devise strategies that, for instance, minimize the amount of edible food that is wasted, foster efficient use of energy and water in the food production process, and simultaneously reduce pollution externalities and create opportunities from recycled energy and nutrients. Characterization of FEW nexus impacts of wasted food, including descriptions of dynamic feedback behaviors, presents a significant research gap and a priority for future work. Large-scale decision making requires more complete understanding of food waste and its management within the FEW nexus, particularly regarding post-disposal impacts related to water. Copyright © 2018 Elsevier Ltd. All rights reserved.

  10. Integrated solid waste management in megacities

    Directory of Open Access Journals (Sweden)

    M.A. Abdoli

    2016-05-01

    Full Text Available Rapid urbanization and industrialization, population growth and economic growth in developing countries make management of municipal solid waste more complex comparing with developed countries. Furthermore, the conventional municipal solid waste management approach often is reductionists, not tailored to handle complexity. Therefore, the need to a comprehensive and multi-disciplinary approach regarding the municipal solid waste management problems is increasing. The concept of integrated solid waste management is accepted for this aim all over the world. This paper analyzes the current situation as well as opportunities and challenges regarding municipal solid waste management in Isfahan according to the integrated solid waste management framework in six aspects: environmental, political/legal, institutional, socio-cultural, financial/economic, technical and performance aspects. Based on the results obtained in this analysis, the main suggestions for future integrated solid waste management of Isfahan are as i promoting financial sustainability by taking the solid waste fee and reducing the expenses through the promoting source collection of recyclable materials, ii improving compost quality and also marketing the compost products simultaneously, iii promoting the private sector involvements throughout the municipal solid waste management system.

  11. Management Information System (MIS: Tool for Monitoring the Waste Management Health Service (RSS and Cost of Treatment

    Directory of Open Access Journals (Sweden)

    Vania Elisabete Schneider

    2013-06-01

    Full Text Available One of the major challenges of solid waste management has been improve and deploy systems that perform monitoring and control of management processes of health service’s waste (HSW. This study aims to evaluate the total cost per category of HSW/day and active bed/day with the handling of HSW in a teaching hospital in northeastern area of Brazil`s Rio Grande do Sul state and identify contributions of a management information system (MIS in the management process, especially considering the generation and segregation of waste. Utilized methodology was developed in two stages: data collection about the management of the HSW and proposition, implementation and feed of a MIS for recording and processing of data related to waste characterization. Results show that whether the management system of the hospital in this study were 100% right, the monthly savings for the treatment of infectious waste would be 18.4% of the costs and 5.83% of costs of chemical waste. The implementation of MIS becomes an essential tool in the evaluation of the management process of HSW since it makes possible to raise issues of fundamental importance to the implementation and evaluation of strategies contained in the HSW management plan. The MIS also represents a tool of easy reference and of great importance to evaluate generation of HSW as it helps to promote the surveillance, identification of sectors that have the biggest problems with segregation, as well as ways to minimize costs and impacts.

  12. Composition of municipal solid waste in Denmark

    DEFF Research Database (Denmark)

    Edjabou, Maklawe Essonanawe

    the comparison of waste data with various objectives. Analysis revealed that Danish residual household waste constitutes mainly food waste (42 – 45% mass per wet basis). Misplaced recyclable materials in residual waste bins, such as paper, board, glass, metal and plastic, amounted to 20% (mass per wet basis...... to 10 kg per employee per year and consisted of 29% paper, 23% plastic and 24% misplaced food waste. Thus, sorting efficiency was estimated at 89% of food waste, accompanied by extremely high purity (99%). These results indicate that the 60% recycling target formulated by the Danish Government for food......In response to continuous pressure on resources, and the requirement for secure and sustainable consumption, public authorities are pushing the efficient use of resources. Among other initiatives, the prevention, reduction and recycling of solid waste have been promoted. In this context, reliable...

  13. Attributes to facilitate e-waste recycling behaviour

    Directory of Open Access Journals (Sweden)

    Senawi Nur Hidayah

    2016-01-01

    Full Text Available This study aims to identify the set of attributes to facilitate electronic waste (e-waste behaviour among the community. E-waste disposal is increasing from year to year in parallel with increasing of global population. The short lifespan of electronics and poor e-waste recycling behaviour is among the main contributors to the steadily increasing of e-waste generated. Current recycling rate among the nation is lacking behind, which is only 10.5%. A questionnaire survey has been conducted among the students in Universiti Teknologi Malaysia to evaluate the current e-waste recycling practice. The results showed that majority of the respondents did not recycle their e-waste on campus. Aggressive efforts is needed to realize the country’s target of 20% recycling rate in year 2020, one of the effective paths is to minimize e-waste generation via active e-waste recycling behaviour among the community. Extensive literatures have been reviewed to classify the attributes to facilitate effective e-waste recycling among the community. Total of five attributes that identified in this study which are Convenience of E- waste Recycling Infrastruture and Services, E-waste Recycling Information, Incentives For E-waste Recycling, Reminder to Recycle E-waste And E-waste Recycling Infrastructure and Services. The set of attributes identified in this study may serve as guideline for the management in designing program to foster e-waste recycling behaviour among the community.

  14. Waste Facilities

    Data.gov (United States)

    Vermont Center for Geographic Information — This dataset was developed from the Vermont DEC's list of certified solid waste facilities. It includes facility name, contact information, and the materials...

  15. Sustainable waste management through end-of-waste criteria development.

    Science.gov (United States)

    Zorpas, Antonis A

    2016-04-01

    The Waste Framework Directive 2000/98 (WFD) contains specific requirements to define end-of-waste criteria (EWC). The main goal of EWC is to remove and eliminate the administrative loads of waste legislation for safe and high-quality waste materials, thereby facilitating and assisting recycling. The target is to produce effective with high quality of recyclables materials, promoting product standardization and quality and safety assurance, and improving harmonization and legal certainty in the recyclable material markets. At the same time, those objectives aim to develop a plan in order to improve the development and wider use of environmental technologies, which reduce pressure on environment and at the same time address the three dimensions of the Lisbon strategy: growth, jobs and environment. This paper presents the importance of EWC, and the approach of setting EWC as EWC affect several management systems as well as sustainable and clean technologies.

  16. Food Waste Avoidance Actions in Food Retailing

    DEFF Research Database (Denmark)

    Kulikovskaja, Viktorija; Aschemann-Witzel, Jessica

    2017-01-01

    Food waste occurs throughout the entire food supply chain, from production to consumption of food in households. Retailers are in a unique position to contribute to food waste avoidance, not only by minimizing the amount of waste in their distribution channels but also by influencing consumer...... attitudes and behaviors. This explorative study aims to identify which food waste avoidance actions are conducted by retailers in Denmark, to which extent, and how they vary across food categories and supermarket chain. Based on an analysis of secondary and empirical data collected via observations...... at retail stores, the authors identify 22 food waste avoidance actions in Danish retail. The results provide new insights into food waste avoidance in retail. Based on the findings, suggestions for further research directions are developed that should serve to identify the most efficient customer targeted...

  17. Tank Waste Transport, Pipeline Plugging, and the Prospects for Reducing the Risk of Waste Transfers

    Energy Technology Data Exchange (ETDEWEB)

    Welch, T.D.

    2001-09-27

    This report provides an overview of the capabilities and limitations of some current models being applied to the analysis of waste transfers; identifies the modeling capabilities needed to reduce the risk of pipeline plugging during tank waste transfers; and summarizes ongoing, planned, and future work needed to add these capabilities. Development of improved waste transport modeling tools with these capabilities will also help with waste transfer planning and evaluation, process control, and diagnosis of plugging events. Other potential applications include evaluation of waste-mixing scenarios, analysis of waste transfer stability, analysis of waste-unplugging alternatives, minimization of water addition, maximization of system availability, evaluation of risk-reduction strategies, and evaluation of cost-reduction strategies.

  18. How to make a minimal genome for synthetic minimal cell.

    Science.gov (United States)

    Zhang, Liu-Yan; Chang, Su-Hua; Wang, Jing

    2010-05-01

    As a key focus of synthetic biology, building a minimal artificial cell has given rise to many discussions. A synthetic minimal cell will provide an appropriate chassis to integrate functional synthetic parts, devices and systems with functions that cannot generally be found in nature. The design and construction of a functional minimal genome is a key step while building such a cell/chassis since all the cell functions can be traced back to the genome. Kinds of approaches, based on bioinformatics and molecular biology, have been developed and proceeded to derive essential genes and minimal gene sets for the synthetic minimal genome. Experiments about streamlining genomes of model bacteria revealed genome reduction led to unanticipated beneficial properties, such as high electroporation efficiency and accurate propagation of recombinant genes and plasmids that were unstable in other strains. Recent achievements in chemical synthesis technology for large DNA segments together with the rapid development of the whole-genome sequencing, have transferred synthesis of genes to assembly of the whole genomes based on oligonucleotides, and thus created strong preconditions for synthesis of artificial minimal genome. Here in this article, we review briefly the history and current state of research in this field and summarize the main methods for making a minimal genome. We also discuss the impacts of minimized genome on metabolism and regulation of artificial cell.

  19. Electrochemical/Pyrometallurgical Waste Stream Processing and Waste Form Fabrication

    Energy Technology Data Exchange (ETDEWEB)

    Steven Frank; Hwan Seo Park; Yung Zun Cho; William Ebert; Brian Riley

    2015-07-01

    This report summarizes treatment and waste form options being evaluated for waste streams resulting from the electrochemical/pyrometallurgical (pyro ) processing of used oxide nuclear fuel. The technologies that are described are South Korean (Republic of Korea – ROK) and United States of America (US) ‘centric’ in the approach to treating pyroprocessing wastes and are based on the decade long collaborations between US and ROK researchers. Some of the general and advanced technologies described in this report will be demonstrated during the Integrated Recycle Test (IRT) to be conducted as a part of the Joint Fuel Cycle Study (JFCS) collaboration between US Department of Energy (DOE) and ROK national laboratories. The JFCS means to specifically address and evaluated the technological, economic, and safe guard issues associated with the treatment of used nuclear fuel by pyroprocessing. The IRT will involve the processing of commercial, used oxide fuel to recover uranium and transuranics. The recovered transuranics will then be fabricated into metallic fuel and irradiated to transmutate, or burn the transuranic elements to shorter lived radionuclides. In addition, the various process streams will be evaluated and tested for fission product removal, electrolytic salt recycle, minimization of actinide loss to waste streams and waste form fabrication and characterization. This report specifically addresses the production and testing of those waste forms to demonstrate their compatibility with treatment options and suitability for disposal.

  20. Indonesia municiple solid waste life cycle and environmental monitoring: current situation, before and future challenges

    Science.gov (United States)

    Susmono

    2017-03-01

    Indonesia is a big country with circa 250 million population, with more than 500 Local Governments and they are going to improve their municiple solid waste dumping method from Open Dumping to Sanitary Landfill (SLF) and to promote Reduce-Reuse-Recycling (3R) since many years ago, and it is strengthened by issuing of Solid Waste Management Act No.18/2008, MSW Government Regulation No.12/2012 and other regulations which are issued by Central Government and Local Governments. During “Water and Sanitation Decade 1980-1990” through “Integrated Urban Infrastructures Development Program” some pilot project such as 30 units of 3R station were developed in the urban areas, and modified or simplification of SLF call Controlled Landfill (CLF) were implemented. In the year of 2002 about 45 units of composting pilot projects were developed under “Western Java Environmental Management Project”, and the result was notified that some of them are not sustain because many aspects. At the beginning of 2007 until now, some pilot projects of 3R were continued in some cities and since 2011 some Waste Banks are growing fast. In the year of 2014 was recorded that of 70 % of 3Rs in Java Island well developed (2014, Directorate of Environment Sanitation Report), and in the year of 2012 was recorded that development of Communal Waste Banks were growing fast during two months from 400 units to 800 units (2012, Ministry of Environment report), now more Communal Waste Banks all ready exist. After the last overview monitoring activity by Ministry of Environment and JICA (2008), because of lack of data is very difficult to give current accurate information of Municiple Solid Waste Handling in Indonesia. Nevertheless some innovation are developed because of impact of many pilot projects, Adipura City Cleanest Competition among Local Governments and growing of the spirit of autonomous policy of Local Governments, but some Local Governments still dependence on Central Government support

  1. Assessing the effectiveness of Denmark's waste tax

    DEFF Research Database (Denmark)

    Andersen, Mikael Skou

    1998-01-01

    pollution from incinerators. Denmark responded to this situation by adopting a comprehensive waste management policy that included an innovative tax on waste designed to promote the reuse and recycling of many types of waste. Now that the tax has been in place for a decade, there is enough data to assess...... its effectiveness. Such an assessment has implications that extend far beyond Denmark. To date, six other countries in Europe (Austria, Belgium, Finland, France, the Netherlands, and the United Kingdom) have adopted waste taxes at the national level, and two others (Norway and Sweden) are considering...

  2. Minimal massive 3D gravity

    NARCIS (Netherlands)

    Bergshoeff, Eric; Hohm, Olaf; Merbis, Wout; Routh, Alasdair J.; Townsend, Paul K.

    2014-01-01

    We present an alternative to topologically massive gravity (TMG) with the same 'minimal' bulk properties; i.e. a single local degree of freedom that is realized as a massive graviton in linearization about an anti-de Sitter (AdS) vacuum. However, in contrast to TMG, the new 'minimal massive gravity'

  3. Energy minimization of ferromagnetic particles

    Science.gov (United States)

    Qu, Heliang; Li, Jiangyu

    2004-07-01

    In this paper, we present an energy-minimization theory of ferromagnetic particles to characterize the magnetization reversal and hysteresis loop of ferromagnetic polycrystals, with the inter-granular magneto-static interactions accounted for through the effective medium approximation. The energy-minimizing magnetization distribution is determined, and the remanence and coercivity are predicted.

  4. Optimization of municipal solid waste collection and transportation routes

    Energy Technology Data Exchange (ETDEWEB)

    Das, Swapan, E-mail: swapan2009sajal@gmail.com; Bhattacharyya, Bidyut Kr., E-mail: bidyut53@yahoo.co.in

    2015-09-15

    Graphical abstract: Display Omitted - Highlights: • Profitable integrated solid waste management system. • Optimal municipal waste collection scheme between the sources and waste collection centres. • Optimal path calculation between waste collection centres and transfer stations. • Optimal waste routing between the transfer stations and processing plants. - Abstract: Optimization of municipal solid waste (MSW) collection and transportation through source separation becomes one of the major concerns in the MSW management system design, due to the fact that the existing MSW management systems suffer by the high collection and transportation cost. Generally, in a city different waste sources scatter throughout the city in heterogeneous way that increase waste collection and transportation cost in the waste management system. Therefore, a shortest waste collection and transportation strategy can effectively reduce waste collection and transportation cost. In this paper, we propose an optimal MSW collection and transportation scheme that focus on the problem of minimizing the length of each waste collection and transportation route. We first formulize the MSW collection and transportation problem into a mixed integer program. Moreover, we propose a heuristic solution for the waste collection and transportation problem that can provide an optimal way for waste collection and transportation. Extensive simulations and real testbed results show that the proposed solution can significantly improve the MSW performance. Results show that the proposed scheme is able to reduce more than 30% of the total waste collection path length.

  5. Minimal Webs in Riemannian Manifolds

    DEFF Research Database (Denmark)

    Markvorsen, Steen

    2008-01-01

    For a given combinatorial graph $G$ a {\\it geometrization} $(G, g)$ of the graph is obtained by considering each edge of the graph as a $1-$dimensional manifold with an associated metric $g$. In this paper we are concerned with {\\it minimal isometric immersions} of geometrized graphs $(G, g......)$ into Riemannian manifolds $(N^{n}, h)$. Such immersions we call {\\em{minimal webs}}. They admit a natural 'geometric' extension of the intrinsic combinatorial discrete Laplacian. The geometric Laplacian on minimal webs enjoys standard properties such as the maximum principle and the divergence theorems, which...... are of instrumental importance for the applications. We apply these properties to show that minimal webs in ambient Riemannian spaces share several analytic and geometric properties with their smooth (minimal submanifold) counterparts in such spaces. In particular we use appropriate versions of the divergence...

  6. Minimal Surfaces for Hitchin Representations

    DEFF Research Database (Denmark)

    Li, Qiongling; Dai, Song

    2018-01-01

    . In this paper, we investigate the properties of immersed minimal surfaces inside symmetric space associated to a subloci of Hitchin component: $q_n$ and $q_{n-1}$ case. First, we show that the pullback metric of the minimal surface dominates a constant multiple of the hyperbolic metric in the same conformal...... class and has a strong rigidity property. Secondly, we show that the immersed minimal surface is never tangential to any flat inside the symmetric space. As a direct corollary, the pullback metric of the minimal surface is always strictly negatively curved. In the end, we find a fully decoupled system......Given a reductive representation $\\rho: \\pi_1(S)\\rightarrow G$, there exists a $\\rho$-equivariant harmonic map $f$ from the universal cover of a fixed Riemann surface $\\Sigma$ to the symmetric space $G/K$ associated to $G$. If the Hopf differential of $f$ vanishes, the harmonic map is then minimal...

  7. Analysis on 3RWB model (Reduce, reuse, recycle, and waste bank) in comprehensive waste management toward community-based zero waste

    Science.gov (United States)

    Affandy, Nur Azizah; Isnaini, Enik; Laksono, Arif Budi

    2017-06-01

    Waste management becomes a serious issue in Indonesia. Significantly, waste production in Lamongan Regency is increasing in linear with the growth of population and current people activities, creating a gap between waste production and waste management. It is a critical problem that should be solved immediately. As a reaction to the issue, the Government of Lamongan Regency has enacted a new policy regarding waste management through a program named Lamongan Green and Clean (LGC). From the collected data, it showed that the "wet waste" or "organic waste" was approximately 63% of total domestic waste. With such condition, it can be predicted that the trashes will decompose quite quickly. From the observation, it was discovered that the generated waste was approximately 0.25 kg/person/day. Meanwhile, the number of population in Tumenggungan Village, Lamongan (data obtained from Monograph in Lamongan district, 2012) was 4651 people. Thus, it can be estimated the total waste in Lamongan was approximately 0.25 kg/person/day x 4651 characters = 930 kg/day. Within 3RWB Model, several stages have to be conducted. In the planning stage, the promotion of self-awareness among the communities in selecting and managing waste due to their interest in a potential benefit, is done. It indicated that community's awareness of waste management waste grew significantly. Meanwhile in socialization stage, each village staff, environmental expert, and policymaker should bear significant role in disseminating the awareness among the people. In the implementation phase, waste management with 3RWB model is promoted by applying it among of the community, starting from selection, waste management, until recycled products sale through the waste bank. In evaluation stage, the village managers, environmental expert, and waste managers are expected to regularly supervise and evaluate the whole activity of the waste management.

  8. The 'bankability' of the new waste technologies: an econometric method for risk sharing in private finance waste contracts.

    Science.gov (United States)

    Black, I; Seaton, R; Chackiath, S; Wagland, S T; Pollard, S J T; Longhurst, P J

    2011-12-01

    The identification of risk and its appropriate allocation to partners in project consortia is essential for minimizing overall project risks, ensuring timely delivery and maximizing benefit for money invested. Risk management guidance available from government bodies, especially in the UK, does not specify methodologies for quantitative risk assessment, nor does it offer a procedure for allocating risk among project partners. Here, a methodology to quantify project risk and potential approaches to allocating risk and their implications are discussed. Construction and operation of a waste management facility through a public-private finance contract are discussed. Public-private partnership contracts are special purpose vehicle (SPV) financing methods promoted by the UK government to boost private sector investment in facilities for public service enhancement. Our findings question the appropriateness of using standard deviation as a measure for project risk and confirm the concept of portfolio theory, suggesting the pooling of risk can reduce total risk and its impact.

  9. Minimal Poems Written in 1979 Minimal Poems Written in 1979

    Directory of Open Access Journals (Sweden)

    Sandra Sirangelo Maggio

    2008-04-01

    Full Text Available The reading of M. van der Slice's Minimal Poems Written in 1979 (the work, actually, has no title reminded me of a book I have seen a long time ago. called Truth, which had not even a single word printed inside. In either case we have a sample of how often excentricities can prove efficient means of artistic creativity, in this new literary trend known as Minimalism. The reading of M. van der Slice's Minimal Poems Written in 1979 (the work, actually, has no title reminded me of a book I have seen a long time ago. called Truth, which had not even a single word printed inside. In either case we have a sample of how often excentricities can prove efficient means of artistic creativity, in this new literary trend known as Minimalism.

  10. Talking Trash: Bringing Research into Action while Reducing Household Solid Waste

    Science.gov (United States)

    O'Connell, Elizabeth J.

    2012-01-01

    This dissertation was an exploration of how changing the waste system is a necessary part of achieving sustainable human systems and how transforming consumer attitudes towards waste is a vital piece of sustainable waste management. This research was also an exploration of the attitudes and beliefs that promote and prohibit waste reduction…

  11. Minimal flows and their extensions

    CERN Document Server

    Auslander, J

    1988-01-01

    This monograph presents developments in the abstract theory of topological dynamics, concentrating on the internal structure of minimal flows (actions of groups on compact Hausdorff spaces for which every orbit is dense) and their homomorphisms (continuous equivariant maps). Various classes of minimal flows (equicontinuous, distal, point distal) are intensively studied, and a general structure theorem is obtained. Another theme is the ``universal'' approach - entire classes of minimal flows are studied, rather than flows in isolation. This leads to the consideration of disjointness of flows, w

  12. The use of ACV in the integrated waste systems of waste management; El uso del ACV en el desarrollo de sistemas integrados de gestion de residuos

    Energy Technology Data Exchange (ETDEWEB)

    McDougall, F. R.; Navarro, M

    2000-07-01

    The treatment systems of Solid Wastes must be conceived for minimizing the environment charge originated by them and to be economically assumed by the sectors of a community. The waste integrated management represents a global proposal which implies a wide range of different treatment options for all waste. (Author)

  13. Wastes and by-products - alternatives for agricultural use

    Energy Technology Data Exchange (ETDEWEB)

    Boles, J.L.; Craft, D.J.; Parker, B.R.

    1994-10-01

    Top address a growing national problem with generation of wastes and by-products, TVA has been involved for several years with developing and commercializing environmentally responsible practices for eliminating, minimizing, or utilizing various wastes/by-products. In many cases, reducing waste generation is impractical, but the wastes/by-products can be converted into other environmentally sound products. In some instances, conversion of safe, value-added agricultural products in the best or only practical alternative. TVA is currently involved with a diversity of projects converting wastes/by-products into safe, economical, and agriculturally beneficial products. Environmental improvement projects have involved poultry litter, cellulosic wastes, used battery acid, ammonium sulfate fines, lead smelting effluents, deep-welled sulfuric acid/ammonium bisulfate solutions, wood ash, waste magnesium ammonium sulfate slurry from recording tape production, and ammunition plant waste sodium nitrate/ammonium nitrate streams.

  14. Waste disposal

    CERN Multimedia

    2006-01-01

    We should like to remind you that you can have all commonplace, conventional waste (combustible, inert, wood, etc.) disposed of by the TS-FM Group. Requests for the removal of such waste should be made by contacting FM Support on tel. 77777 or by e-mail (Fm.Support@cern.ch). For requests to be acted upon, the following information must be communicated to FM Support: budget code to be debited for the provision and removal of the skip / container; type of skip required (1m3, 4 m3, 7 m3, 15 m3, 20 m3, 30 m3); nature of the waste to be disposed of (bulky objects, cardboard boxes, etc.); building concerned; details of requestor (name, phone number, department, group, etc.). We should also like to inform you that the TS-FM Group can arrange for waste to be removed from work-sites for firms under contract to CERN, provided that the prior authorisation of the CERN Staff Member in charge of the contract is obtained and the relevant disposal/handling charges are paid. You are reminded that the selective sorting...

  15. Waste disposal

    CERN Multimedia

    2006-01-01

    We should like to remind you that you can have all commonplace, conventional waste (combustible, inert, wood, etc.) disposed of by the TS-FM Group. Requests for the removal of such waste should be made by contacting FM Support on tel. 77777 or by e-mail (Fm.Support@cern.ch). For requests to be acted upon, the following information must be communicated to FM Support: budget code to be debited for the provision and removal of the skip / container. type of skip required (1m3, 4 m3, 7 m3, 15 m3, 20 m3, 30 m3). nature of the waste to be disposed of (bulky objects, cardboard boxes, etc.). building concerned. details of requestor (name, phone number, department, group, etc.). We should also like to inform you that the TS-FM Group can arrange for waste to be removed from work-sites for firms under contract to CERN, provided that the prior authorisation of the CERN Staff Member in charge of the contract is obtained and the relevant disposal/handling charges are paid. You are reminded that the selective sorting o...

  16. Human waste

    NARCIS (Netherlands)

    Amin, Md Nurul; Kroeze, Carolien; Strokal, Maryna

    2017-01-01

    Many people practice open defecation in south Asia. As a result, lot of human waste containing nutrients such as nitrogen (N) and phosphorus (P) enter rivers. Rivers transport these nutrients to coastal waters, resulting in marine pollution. This source of nutrient pollution is, however, ignored in

  17. Dairy Wastes.

    Science.gov (United States)

    Pico, Richard F.

    1978-01-01

    Presents a literature review of wastes from the dairy industry covering publications of 1976-77. This review covers: (1) government regulations; (2) ion-plant control of dairy effluents; (3) dairy effluent treatment methods; and (4) research on dairy effluents. A list of 26 references is also presented. (HM)

  18. Heart bypass surgery - minimally invasive

    Science.gov (United States)

    ... and lifestyle Cholesterol - drug treatment Controlling your high blood pressure Dietary fats explained Fast food tips Heart attack - discharge Heart attack - what to ask your doctor Heart bypass surgery - minimally invasive - discharge Heart disease - risk factors Heart pacemaker - discharge ...

  19. Technical and economic assessment of power generation from municipal solid waste incineration on steam cycle

    Energy Technology Data Exchange (ETDEWEB)

    Romero Luna, Carlos Manuel; Carrocci, Luiz Roberto; Ferrufino, Gretta Larisa Aurora Arce; Balestieri, Jose Antonio Perrella [Dept. of Energy. UNESP, Sao Paulo State University, Guaratingueta, SP (Brazil)], e-mails: carrocci@feg.unesp.br, perrella@feg.unesp.br

    2010-07-01

    Nowadays, there is a concern in development of environmentally friendly methods for a municipal solid waste (MSW) management and demand for renewable energy sources. The source of waste is increasing, and the capacity and availability Landfill treatment and disposal are coming to be insufficient. In Sao Paulo City, the 10 million inhabitants produce 10,000 t of residential solid waste daily, being that 76% this quantity goes to landfill sites. In order to adopt a new treatment technology for MSW that will promote a solution minimizing this problem, within the order of priorities regarding waste management, the MSW incineration with energy recovery shown as the leading choice on the point of view of efficiency in converting energy. MSW incineration with energy recovery received wide acceptance from various countries including European Union members and the rest of the world in the past 15 years. Incineration has the ability decrease 90 % the volume of waste to be used in landfills, increasing the useful life of existing as well as a reduction in the emission of greenhouse gases. MSW incineration systems have a low global warming potential (GWP). now has become a less important source of dioxins and furans due to the current available technology. MSW incineration with energy recovery could contribute considerably in the energy matrix, thus promote the conservation of non-renewable resources. This paper proposes the assessment the technical and economic feasibility of a steam cycle with conventional steam generator for MSW incineration with energy recovery for power generation in Sao Paulo City. Will be developed a thermoeconomic analysis aiming at the total power generation product of MSW incineration, and the assessment investment cost regarding the total sale of power generated. The study shows that Sao Paulo City has potential for power generation from the MSW incineration, although it has a high cost investment this technology shown as a suitable alternative for

  20. Trends in the Drilling Waste Management

    Directory of Open Access Journals (Sweden)

    Lucyna Czekaj

    2006-10-01

    Full Text Available Petroleum Industry is trying to achieve sustainable development goals. Each year new solutions are implemented to minimize the environmental impact of drilling operations. The paper presents trends in the drilling waste management caused by introducing the sustainable development into the petroleum industry. Old solutions such as the drilling waste disposal at the waste dump or dumping ground are not acceptable from the environmental point of view. The paper presents an analysis of new solutions as the sustainable solutions. The most important problem is the chemical pollution in cuttings and the waste drilling mud. The industrial solutions as well as the laboratory research on the pollution removing from drilling wastes are analysed. The most promising method seems to be the recycling and design for the environment of drilling mud.

  1. Waste processing building with incineration technology

    Science.gov (United States)

    Wasilah, Wasilah; Zaldi Suradin, Muh.

    2017-12-01

    In Indonesia, waste problem is one of major problem of the society in the city as part of their life dynamics. Based on Regional Medium Term Development Plan of South Sulawesi Province in 2013-2018, total volume and waste production from Makassar City, Maros, Gowa, and Takalar Regency estimates the garbage dump level 9,076.949 m3/person/day. Additionally, aim of this design is to present a recommendation on waste processing facility design that would accommodate waste processing process activity by incineration technology and supported by supporting activity such as place of education and research on waste, and the administration activity on waste processing facility. Implementation of incineration technology would reduce waste volume up to 90% followed by relative negative impact possibility. The result planning is in form of landscape layout that inspired from the observation analysis of satellite image line pattern of planning site and then created as a building site pattern. Consideration of building orientation conducted by wind analysis process and sun path by auto desk project Vasari software. The footprint designed by separate circulation system between waste management facility interest and the social visiting activity in order to minimize the croos and thus bring convenient to the building user. Building mass designed by inseparable connection series system, from the main building that located in the Northward, then connected to a centre visitor area lengthways, and walked to the waste processing area into the residue area in the Southward area.

  2. Report on the project for spread/promotion of technology for the industrial waste optimized treatment in the Asian region; Asia chiiki sangyo haikibutsu tekiseika shori gijutsu nado fukyu sokushin jigyo hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The International Symposium `98 on the industrial waste problem in the Asian region was held in Tokyo on February 18, 1998. MITI commented on the present situation of the industrial waste problem in Japan and Japan`s environmental tackling toward the Asian region, and also Asian countries (China, the Philippines, Thailand and Korea) made reports. Japan reported on environmental preservation measures taken in the industrial circle, the industrial waste problem at companies which advanced into Asian countries, effects of the Basel Convention (which restricts border-crossing movement of harmful wastes) on recycle activities, Japan`s role in Asia, etc. In the panel discussion, discussions were made on human interchange in the informatization, recycling technology, shortage of personnel concerned with environmental protection, construction of a network in the Asian region and Japan` s role, etc. As to the treatment system for waste, the necessity was recognized of studying systems which meet with actual states of each country. It is also necessary to go on with discussing how the system should be for cooperation between governments and private companies. Importance of the recycle and information exchange was emphasized. 10 refs., 14 figs., 27 tabs.

  3. WARRP Decon-13: Subject Matter Expert (SME) Meeting Waste Screening and Waste Minimization Methodologies Project

    Science.gov (United States)

    2012-08-01

    requirements for these systems followed. Another suggestion was to consider plasma arc vitrification as it was used in Russia for animal carcass...removal) treatment/disposal Segmented gate system Soil washing Composting Plasma arc vitrification Incineration Low/Disadvantageous...council. Finally, Ms. Sell acknowledged Garry Briese for his assistance in securing the venue for the SME Meeting and introduced him as the first speaker

  4. Duality of Health Promotion and Sustainable Development

    DEFF Research Database (Denmark)

    Pedersen, Kirsten Bransholm; Land, Birgit; Kjærgård, Bente

    2015-01-01

    reduction and how these strategies affect the prospects for promoting health and sustainable food production and consumption. Danish food waste reduction strategies are used as examples with references to selected policy documents on food waste reduction strategies launched by international organisations...... sustainability and, vice versa, sustainability conditions health. Thus, to avoid unintended, negative effects the strategies directed towards sustainable development must be correlated with strategies for health promotion. The conceptual model is used to take a closer look at the complexities of food waste...... such as FAO, WHO, and the UN. We conclude that the strategies directed towards reducing food waste ignore the health and sustainability problems related to the oversupply of food. Neither do the Danish proponents of food waste reduction strategies explicitly articulate the built-in option to reduce the supply...

  5. Economic Analysis of Waste Management in Nigeria | NDUKA ...

    African Journals Online (AJOL)

    The generation, utilization and disposal of wastes (which constitute environmental hazards) are highlighted in this paper as a network flow problem. In this configuration, we construct and solve as optimal network flow, the problem of minimizing the cost of disposing wastes from sources of generation to dumpsites.

  6. Frontiers and prospects for recycling Waste Electrical and Electronic ...

    African Journals Online (AJOL)

    This paper reviews the frontlines and projections for the recycling of waste electrical and electronic equipment (WEEE) in Nigeria. The paper identified the sources of WEEE, showed chemical characterization of some WEEE components and presented measures to minimize these wastes through recycling opportunities.

  7. Minimally invasive operative care. I. Minimal intervention and concepts for minimally invasive cavity preparations.

    Science.gov (United States)

    Peters, M C; McLean, M E

    2001-01-01

    From the mainly reparative dentistry of the 20th century, contemporary dentistry shifts towards a minimal intervention (MI) approach encompassing up-to-date caries diagnosis and risk assessment before arriving at a treatment decision. An overview is provided of incorporating MI philosophy into the field of operative dentistry. The ultimate goal of MI is to extend the lifetime of restored teeth with as little intervention as possible. When operative care is indicated, it should be aimed at "prevention of extension." Black's principles for cavity design are considered and put in the perspective of minimally invasive operative care. Guiding principles for contemporary adhesive cavities are reviewed. Contemporary operative care should be based on a minimally invasive approach. Minimal intervention is not just a technique, it is a philosophy!

  8. Minimally invasive cervical spine surgery.

    Science.gov (United States)

    Skovrlj, Branko; Qureshi, Sheeraz A

    2017-06-01

    Degenerative disorders of the cervical spine requiring surgical intervention have become increasingly more common over the past decade. Traditionally, open surgical approaches have been the mainstay of surgical treatment. More commonly, minimally invasive techniques are being developed with the intent to decrease surgical morbidity and iatrogenic spinal instability. This study will review four minimally invasive cervical techniques that have been increasingly utilized in the treatment of degenerative cervical spine disease. A series of PubMed-National Library of Medicine searches were performed. Only articles in English journals or with published with English language translations were included. Level of evidence of the selected articles was assessed. The significant incidence of postoperative dysphagia following ACDF has led to the development and increased use of zero-profile, stand-alone anterior cervical cages. The currently available literature examining the safety and effectiveness of zero-profile interbody devices supports the use of these devices in patients undergoing single-level ACDF. A multitude of studies demonstrating the significant incidence and impact of axial neck pain following open posterior spine surgery have led to a wave of research and development of techniques aimed at minimizing posterior cervical paraspinal disruption while achieving appropriate neurological decompression and/or spinal fixation. The currently available literature supports the use of minimally invasive posterior cervical laminoforaminotomy for the treatment of single-level radiculopathy. The literature suggests that fluoroscopically-assisted percutaneous cervical lateral mass screw fixation appears to be a technically feasible, safe and minimally invasive technique. Based on the currently available literature it appears that the DTRAX® expandable cage system is an effective minimally invasive posterior cervical technique for the treatment of single-level cervical

  9. DOE model conference on waste management and environmental restoration

    Energy Technology Data Exchange (ETDEWEB)

    1990-01-01

    Reports dealing with current topics in waste management and environmental restoration were presented at this conference in six sessions. Session 1 covered the Hot Topics'' including regulations and risk assessment. Session 2 dealt with waste reduction and minimization; session 3 dealt with waste treatment and disposal. Session 4 covered site characterization and analysis. Environmental restoration and associated technologies wee discussed in session 5 and 6. Individual papers have been cataloged separately.

  10. Minimal but non-minimal inflation and electroweak symmetry breaking

    Energy Technology Data Exchange (ETDEWEB)

    Marzola, Luca [National Institute of Chemical Physics and Biophysics,Rävala 10, 10143 Tallinn (Estonia); Institute of Physics, University of Tartu,Ravila 14c, 50411 Tartu (Estonia); Racioppi, Antonio [National Institute of Chemical Physics and Biophysics,Rävala 10, 10143 Tallinn (Estonia)

    2016-10-07

    We consider the most minimal scale invariant extension of the standard model that allows for successful radiative electroweak symmetry breaking and inflation. The framework involves an extra scalar singlet, that plays the rôle of the inflaton, and is compatibile with current experimental bounds owing to the non-minimal coupling of the latter to gravity. This inflationary scenario predicts a very low tensor-to-scalar ratio r≈10{sup −3}, typical of Higgs-inflation models, but in contrast yields a scalar spectral index n{sub s}≃0.97 which departs from the Starobinsky limit. We briefly discuss the collider phenomenology of the framework.

  11. Pollution prevention opportunity assessment for the SNL/California waste management facilities

    Energy Technology Data Exchange (ETDEWEB)

    Braye, S.; Phillips, N.M. [Sandia National Labs., Livermore, CA (United States). Environmental Protection Dept.

    1995-01-01

    SNL/California`s waste management facilities, Bldgs. 961 and 962-2, generate a secondary stream of hazardous and radioactive waste. This waste stream is generated mainly during the processing and handling of hazardous, radioactive, and mixed wastes (primary waste stream), which are generated by the laboratories, and when cleaning up spills. The secondary waste stream begins with the removal of a generator`s hazardous, radioactive, and mixed waste from specified collection areas. The waste stream ends when the containers of processed waste are loaded for shipment off-site. The total amount of secondary hazardous waste generated in the waste management facilities from January 1993 to July 1994 was 1,160.6 kg. The total amount of secondary radioactive waste generated during the same period was 1,528.8 kg (with an activity of 0.070 mCi). Mixed waste usually is not generated in the secondary waste stream. This pollution prevention opportunity assessment (PPOA) was conducted using the graded approach methodology developed by the Department of Energy (DOE) PPOA task group. The original method was modified to accommodate the needs of Sandia`s site-specific processes. The options generated for potential hazardous waste minimization, cost savings, and environmental health and safety were the result of a waste minimization team effort. The results of the team efforts are summarized.

  12. Minimally Invasive Video-Assisted versus Minimally Invasive Nonendoscopic Thyroidectomy

    Directory of Open Access Journals (Sweden)

    Zdeněk Fík

    2014-01-01

    Full Text Available Minimally invasive video-assisted thyroidectomy (MIVAT and minimally invasive nonendoscopic thyroidectomy (MINET represent well accepted and reproducible techniques developed with the main goal to improve cosmetic outcome, accelerate healing, and increase patient’s comfort following thyroid surgery. Between 2007 and 2011, a prospective nonrandomized study of patients undergoing minimally invasive thyroid surgery was performed to compare advantages and disadvantages of the two different techniques. There were no significant differences in the length of incision to perform surgical procedures. Mean duration of hemithyroidectomy was comparable in both groups, but it was more time consuming to perform total thyroidectomy by MIVAT. There were more patients undergoing MIVAT procedures without active drainage in the postoperative course and we also could see a trend for less pain in the same group. This was paralleled by statistically significant decreased administration of both opiates and nonopiate analgesics. We encountered two cases of recurrent laryngeal nerve palsies in the MIVAT group only. MIVAT and MINET represent safe and feasible alternative to conventional thyroid surgery in selected cases and this prospective study has shown minimal differences between these two techniques.

  13. Minimal Erythema Dose (MED) testing.

    Science.gov (United States)

    Heckman, Carolyn J; Chandler, Rachel; Kloss, Jacqueline D; Benson, Amy; Rooney, Deborah; Munshi, Teja; Darlow, Susan D; Perlis, Clifford; Manne, Sharon L; Oslin, David W

    2013-05-28

    Ultraviolet radiation (UV) therapy is sometimes used as a treatment for various common skin conditions, including psoriasis, acne, and eczema. The dosage of UV light is prescribed according to an individual's skin sensitivity. Thus, to establish the proper dosage of UV light to administer to a patient, the patient is sometimes screened to determine a minimal erythema dose (MED), which is the amount of UV radiation that will produce minimal erythema (sunburn or redness caused by engorgement of capillaries) of an individual's skin within a few hours following exposure. This article describes how to conduct minimal erythema dose (MED) testing. There is currently no easy way to determine an appropriate UV dose for clinical or research purposes without conducting formal MED testing, requiring observation hours after testing, or informal trial and error testing with the risks of under- or over-dosing. However, some alternative methods are discussed.

  14. Minimizing Costs Can Be Costly

    Directory of Open Access Journals (Sweden)

    Rasmus Rasmussen

    2010-01-01

    Full Text Available A quite common practice, even in academic literature, is to simplify a decision problem and model it as a cost-minimizing problem. In fact, some type of models has been standardized to minimization problems, like Quadratic Assignment Problems (QAPs, where a maximization formulation would be treated as a “generalized” QAP and not solvable by many of the specially designed softwares for QAP. Ignoring revenues when modeling a decision problem works only if costs can be separated from the decisions influencing revenues. More often than we think this is not the case, and minimizing costs will not lead to maximized profit. This will be demonstrated using spreadsheets to solve a small example. The example is also used to demonstrate other pitfalls in network models: the inability to generally balance the problem or allocate costs in advance, and the tendency to anticipate a specific type of solution and thereby make constraints too limiting when formulating the problem.

  15. Minimal Marking: A Success Story

    Directory of Open Access Journals (Sweden)

    Anne McNeilly

    2014-11-01

    Full Text Available The minimal-marking project conducted in Ryerson’s School of Journalism throughout 2012 and early 2013 resulted in significantly higher grammar scores in two first-year classes of minimally marked university students when compared to two traditionally marked classes. The “minimal-marking” concept (Haswell, 1983, which requires dramatically more student engagement, resulted in more successful learning outcomes for surface-level knowledge acquisition than the more traditional approach of “teacher-corrects-all.” Results suggest it would be effective, not just for grammar, punctuation, and word usage, the objective here, but for any material that requires rote-memory learning, such as the Associated Press or Canadian Press style rules used by news publications across North America.

  16. Use of food waste, fish waste and food processing waste for China's aquaculture industry: Needs and challenge.

    Science.gov (United States)

    Mo, Wing Yin; Man, Yu Bon; Wong, Ming Hung

    2018-02-01

    China's aquaculture industry is growing dramatically in recent years and now accounts for 60.5% of global aquaculture production. Fish protein is expected to play an important role in China's food security. Formulated feed has become the main diet of farmed fish. The species farmed have been diversified, and a large amount of 'trash fish' is directly used as feed or is processed into fishmeal for fish feed. The use of locally available food waste as an alternative protein source for producing fish feed has been suggested as a means of tackling the problem of sourcing safe and sustainable feed. This paper reviews the feasibility of using locally available waste materials, including fish waste, okara and food waste. Although the fishmeal derived from fish waste, okara or food waste is less nutritious than fishmeal from whole fish or soybean meal, most fish species farmed in China, such as tilapia and various Chinese carp, grow well on diets with minimal amounts of fishmeal and 40% digestible carbohydrate. It can be concluded that food waste is suitable as a component of the diet of farmed fish. However, it will be necessary to revise regulations on feed and feed ingredients to facilitate the use of food waste in the manufacture of fish feed. Copyright © 2017 Elsevier B.V. All rights reserved.

  17. Waste reduction program at Oak Ridge National Laboratory during CY 1989

    Energy Technology Data Exchange (ETDEWEB)

    Schultz, R.M.

    1990-05-01

    Hazardous, radioactive, and mixed wastes are generated at Oak Ridge National Laboratory (ORNL). The State of Tennessee has requested that ORNL organize the waste streams into approximately 30 generic categories for the CY 1989 report so the information is more manageable. The wide diversity of waste complicates both management and compliance with reporting requirements that are designed to apply to production facilities. In recent years, increased effort has been devoted to the minimization of hazardous and radioactive wastes at ORNL. Policy statements supporting such efforts have been issued by both Martin Marietta Energy Systems, Inc., and ORNL management. Motivation is found in federal regulations, DOE policies and guidelines, increased costs and liabilities associated with the management of wastes, and limited disposal options and facility capacities. ORNL's waste minimization efforts have achieved some success. However, because of the diversity and predominantly nonroutine nature of ORNL's containerized wastes, goals for their reduction are difficult to establish. Efforts continue to establish goals that account separately for wastes generated from laboratory cleanouts, to avoid a waste minimization penalty'' for this good housekeeping practice. Generator evaluations to prioritize hazardous waste streams for waste minimization opportunities are planned for FY 1990. These are important first steps to enable the waste reduction program to assign realistic goals. 22 refs., 13 figs., 10 tabs.

  18. 1987 Oak Ridge model conference: Proceedings: Volume I, Part 3, Waste Management

    Energy Technology Data Exchange (ETDEWEB)

    1987-01-01

    A conference sponsored by the United States Department of Energy (DOE), was held on waste management. Topics of discussion were transuranic waste management, chemical and physical treatment technologies, waste minimization, land disposal technology and characterization and analysis. Individual projects are processed separately for the data bases. (CBS)

  19. Does Minimally Invasive Spine Surgery Minimize Surgical Site Infections?

    Science.gov (United States)

    Patel, Ravish Shammi; Dutta, Shumayou

    2016-01-01

    Study Design Retrospective review of prospectively collected data. Purpose To evaluate the incidence of surgical site infections (SSIs) in minimally invasive spine surgery (MISS) in a cohort of patients and compare with available historical data on SSI in open spinal surgery cohorts, and to evaluate additional direct costs incurred due to SSI. Overview of Literature SSI can lead to prolonged antibiotic therapy, extended hospitalization, repeated operations, and implant removal. Small incisions and minimal dissection intrinsic to MISS may minimize the risk of postoperative infections. However, there is a dearth of literature on infections after MISS and their additional direct financial implications. Methods All patients from January 2007 to January 2015 undergoing posterior spinal surgery with tubular retractor system and microscope in our institution were included. The procedures performed included tubular discectomies, tubular decompressions for spinal stenosis and minimal invasive transforaminal lumbar interbody fusion (TLIF). The incidence of postoperative SSI was calculated and compared to the range of cited SSI rates from published studies. Direct costs were calculated from medical billing for index cases and for patients with SSI. Results A total of 1,043 patients underwent 763 noninstrumented surgeries (discectomies, decompressions) and 280 instrumented (TLIF) procedures. The mean age was 52.2 years with male:female ratio of 1.08:1. Three infections were encountered with fusion surgeries (mean detection time, 7 days). All three required wound wash and debridement with one patient requiring unilateral implant removal. Additional direct cost due to infection was $2,678 per 100 MISS-TLIF. SSI increased hospital expenditure per patient 1.5-fold after instrumented MISS. Conclusions Overall infection rate after MISS was 0.29%, with SSI rate of 0% in non-instrumented MISS and 1.07% with instrumented MISS. MISS can markedly reduce the SSI rate and can be an

  20. Minimal Flavor Constraints for Technicolor

    DEFF Research Database (Denmark)

    Sakuma, Hidenori; Sannino, Francesco

    2010-01-01

    We analyze the constraints on the the vacuum polarization of the standard model gauge bosons from a minimal set of flavor observables valid for a general class of models of dynamical electroweak symmetry breaking. We will show that the constraints have a strong impact on the self-coupling and mas......We analyze the constraints on the the vacuum polarization of the standard model gauge bosons from a minimal set of flavor observables valid for a general class of models of dynamical electroweak symmetry breaking. We will show that the constraints have a strong impact on the self...

  1. Waste prevention for sustainable resource and waste management

    DEFF Research Database (Denmark)

    Sakai, Shin-Ichi; Yano, Junya; Hirai, Yasuhiro

    2017-01-01

    a sustainable society. 3R and resource management policies, including waste prevention, will play a crucial role. Approaches using material/substance flow analyses have become sophisticated enough to describe the fate of resources and/or hazardous substances based on human activity and the environment....... Persistent organic pollutants and hazardous compounds should also be taken into account in the situation where recycling activities are globally widespread for the promotion of a material-cycling society....

  2. Preliminary study on enhancing waste management best practice model in Malaysia construction industry

    Science.gov (United States)

    Jamaludin, Amril Hadri; Karim, Nurulzatushima Abdul; Noor, Raja Nor Husna Raja Mohd; Othman, Nurulhidayah; Malik, Sulaiman Abdul

    2017-08-01

    Construction waste management (CWM) is the practice of minimizing and diverting construction waste, demolition debris, and land-clearing debris from disposal and redirecting recyclable resources back into the construction process. Best practice model means best choice from the collection of other practices that was built for purpose of construction waste management. The practice model can help the contractors in minimizing waste before the construction activities will be started. The importance of minimizing wastage will have direct impact on time, cost and quality of a construction project. This paper is focusing on the preliminary study to determine the factors of waste generation in the construction sites and identify the effectiveness of existing construction waste management practice conducted in Malaysia. The paper will also include the preliminary works of planned research location, data collection method, and analysis to be done by using the Analytical Hierarchy Process (AHP) to help in developing suitable waste management best practice model that can be used in the country.

  3. Rethinking the waste hierarchy

    Energy Technology Data Exchange (ETDEWEB)

    Rasmussen, C.; Vigsoe, D. (eds.)

    2005-03-01

    There is an increasing need to couple environmental and economic considerations within waste management. Consumers and companies alike generate ever more waste. The waste-policy challenges of the future lie in decoupling growth in waste generation from growth in consumption, and in setting priorities for the waste management. This report discusses the criteria for deciding priorities for waste management methods, and questions the current principles of EU waste policies. The basis for the discussion is the so-called waste hierarchy which has dominated the waste policy in the EU since the mid-1970s. The waste hierarchy ranks possible methods of waste management. According to the waste hierarchy, the very best solution is to reduce the amount of waste. After that, reuse is preferred to recycling which, in turn, is preferred to incineration. Disposal at a landfill is the least favourable solution. (BA)

  4. Treatment of oily wastes using high-shear rotary ultrafiltration

    Energy Technology Data Exchange (ETDEWEB)

    Reed, B.E.; Viadero, R. Jr.; Young, J. [West Virginia Univ., Morgantown, WV (United States). Dept. of Civil and Environmental Engineering; Lin, W. [North Dakota State Univ., Fargo, ND (United States). Dept. of Civil Engineering

    1997-12-01

    The high-shear rotary ultrafiltration (UF) system uses membrane rotation to provide the turbulence required to minimize concentration polarization and flux decline. The high-shear UF system was effective in concentrating oily wastes from about 5% to as high as 65%. The decoupling of turbulence promotion from feed pressurization/recirculation by rotating the membrane was the primary reason for the improvement in performance over that observed with conventional UF systems. Transitional and gel layer oil concentrations (20% and 50--59%, respectively) were higher than values reported in the literature. Permeate flux was dependent on the temperature and rotational speed. Flux increased by about 45% when the temperature was increased from 43 to 60 C. A larger decrease in waste viscosity, over that predicted for water alone, and increased oil droplet diffusivity were hypothesized as reasons for the stronger than expected flux-temperature relationship. The flux-rotational speed ({omega}) relationship was described by J = f({omega}){sup 0.90}; however, the gel layer exhibited stability with increasing {omega}. The ceramic membrane was superior to the polymeric membrane in regards to permeate flux and quality as well as cleaning and durability.

  5. Other Special Waste

    DEFF Research Database (Denmark)

    Brogaard, Line Kai-Sørensen; Christensen, Thomas Højlund

    2011-01-01

    separately from MSW. Some of these other special wastes are briefly described in this chapter with respect to their definition, quantity and composition, and management options. The special wastes mentioned here are batteries, tires, polyvinylchloride (PVC) and food waste.......In addition to the main types of special waste related to municipal solid waste (MSW) mentioned in the previous chapters (health care risk waste, WEEE, impregnated wood, hazardous waste) a range of other fractions of waste have in some countries been defined as special waste that must be handled...

  6. Microwave technology for waste management applications: Treatment of discarded electronic circuitry

    Energy Technology Data Exchange (ETDEWEB)

    Wicks, G.G. [Westinghouse Savannah River Technology Center, Aiken, SC (United States); Clark, D.E.; Schulz, R.L. [Univ. of Florida, Gainesville, FL (United States)

    1997-01-01

    Significant quantities of hazardous wastes are generated from a multitude of processes and products in today`s society. This waste inventory is not only very large and diverse, but is also growing at an alarming rate. In order to minimize the dangers presented by constituents in these wastes, microwave technologies are being investigated to render harmless the hazardous components and ultimately, to minimize their impact to individuals and the surrounding environment.

  7. Promoter shape varies across populations and affects promoter evolution and expression noise.

    Science.gov (United States)

    Schor, Ignacio E; Degner, Jacob F; Harnett, Dermot; Cannavò, Enrico; Casale, Francesco P; Shim, Heejung; Garfield, David A; Birney, Ewan; Stephens, Matthew; Stegle, Oliver; Furlong, Eileen E M

    2017-04-01

    Animal promoters initiate transcription either at precise positions (narrow promoters) or dispersed regions (broad promoters), a distinction referred to as promoter shape. Although highly conserved, the functional properties of promoters with different shapes and the genetic basis of their evolution remain unclear. Here we used natural genetic variation across a panel of 81 Drosophila lines to measure changes in transcriptional start site (TSS) usage, identifying thousands of genetic variants affecting transcript levels (strength) or the distribution of TSSs within a promoter (shape). Our results identify promoter shape as a molecular trait that can evolve independently of promoter strength. Broad promoters typically harbor shape-associated variants, with signatures of adaptive selection. Single-cell measurements demonstrate that variants modulating promoter shape often increase expression noise, whereas heteroallelic interactions with other promoter variants alleviate these effects. These results uncover new functional properties of natural promoters and suggest the minimization of expression noise as an important factor in promoter evolution.

  8. Hanford Site annual dangerous waste report: Volume 1, Part 1, Generator dangerous waste report, dangerous waste

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-12-31

    This report contains information on hazardous wastes at the Hanford Site. Information consists of shipment date, physical state, chemical nature, waste description, waste number, weight, and waste designation.

  9. Household Waste Recycling: Economics and Policy

    OpenAIRE

    Ankinée Kirakozian

    2015-01-01

    This paper provides a review of economic studies that analyse the use of multiple policies to cope with waste management problems. We discuss the factors that influence selective sorting behaviour, and the most appropriate policies for their promotion. Based on the works analysed, our survey shows the original features of waste as an environmental problem requiring regulation. The traditional approach in which decisions respond to rational behaviour, particularly cost savings, has some limits...

  10. Chemical basis for minimal cognition

    DEFF Research Database (Denmark)

    Hanczyc, Martin; Ikegami, Takashi

    -movement. Different from the mere physicalchemical process, any life system preserves its own identity and consistency with respect to the environment. This homeostasis, rooted on the sensory motor couplings, will organize minimal cognition (see also, Ikegami , T. et al., 2008, BioSys., 91, p.388 ]...

  11. A Defense of Semantic Minimalism

    Science.gov (United States)

    Kim, Su

    2012-01-01

    Semantic Minimalism is a position about the semantic content of declarative sentences, i.e., the content that is determined entirely by syntax. It is defined by the following two points: "Point 1": The semantic content is a complete/truth-conditional proposition. "Point 2": The semantic content is useful to a theory of…

  12. Minimally invasive aortic valve replacement

    DEFF Research Database (Denmark)

    Foghsgaard, Signe; Schmidt, Thomas Andersen; Kjaergard, Henrik K

    2009-01-01

    In this descriptive prospective study, we evaluate the outcomes of surgery in 98 patients who were scheduled to undergo minimally invasive aortic valve replacement. These patients were compared with a group of 50 patients who underwent scheduled aortic valve replacement through a full sternotomy...

  13. Harm minimization among teenage drinkers

    DEFF Research Database (Denmark)

    Jørgensen, Morten Hulvej; Curtis, Tine; Christensen, Pia Haudrup

    2007-01-01

    . In regulating the social context of drinking they relied on their personal experiences more than on formalized knowledge about alcohol and harm, which they had learned from prevention campaigns and educational programmes. CONCLUSIONS: In this study we found that teenagers may help each other to minimize alcohol...

  14. International waste management fact book

    Energy Technology Data Exchange (ETDEWEB)

    Amaya, J P; LaMarche, M N; Upton, J F

    1997-10-01

    Many countries around the world are faced with nuclear and environmental management problems similar to those being addressed by the US Department of Energy. The purpose of this Fact Book is to provide the latest information on US and international organizations, programs, activities and key personnel to promote mutual cooperation to solve these problems. Areas addressed include all aspects of closing the commercial and nuclear fuel cycle and managing the wastes and sites from defense-related, nuclear materials production programs.

  15. Reuse of hydroponic waste solution.

    Science.gov (United States)

    Kumar, Ramasamy Rajesh; Cho, Jae Young

    2014-01-01

    Attaining sustainable agriculture is a key goal in many parts of the world. The increased environmental awareness and the ongoing attempts to execute agricultural practices that are economically feasible and environmentally safe promote the use of hydroponic cultivation. Hydroponics is a technology for growing plants in nutrient solutions with or without the use of artificial medium to provide mechanical support. Major problems for hydroponic cultivation are higher operational cost and the causing of pollution due to discharge of waste nutrient solution. The nutrient effluent released into the environment can have negative impacts on the surrounding ecosystems as well as the potential to contaminate the groundwater utilized by humans for drinking purposes. The reuse of non-recycled, nutrient-rich hydroponic waste solution for growing plants in greenhouses is the possible way to control environmental pollution. Many researchers have successfully grown several plant species in hydroponic waste solution with high yield. Hence, this review addresses the problems associated with the release of hydroponic waste solution into the environment and possible reuse of hydroponic waste solution as an alternative resource for agriculture development and to control environmental pollution.

  16. Minimal cut sets in biochemical reaction networks

    National Research Council Canada - National Science Library

    Klamt, Steffen; Gilles, Ernst Dieter

    2004-01-01

    .... We introduce the concept of minimal cut sets for biochemical networks. A minimal cut set (MCS) is a minimal (irreducible) set of reactions in the network whose inactivation will definitely lead to a failure in certain network functions...

  17. Waste remediation

    Energy Technology Data Exchange (ETDEWEB)

    Halas, Nancy J.; Nordlander, Peter; Neumann, Oara

    2017-01-17

    A system including a steam generation system and a chamber. The steam generation system includes a complex and the steam generation system is configured to receive water, concentrate electromagnetic (EM) radiation received from an EM radiation source, apply the EM radiation to the complex, where the complex absorbs the EM radiation to generate heat, and transform, using the heat generated by the complex, the water to steam. The chamber is configured to receive the steam and an object, wherein the object is of medical waste, medical equipment, fabric, and fecal matter.

  18. The Causes and Costs of Promotion Trauma.

    Science.gov (United States)

    Darling, Lu Ann W.; McGrath, Loraine G.

    1983-01-01

    Minimizing the stress that nurses experience after a promotion requires an understanding of the factors associated with moving up the managerial ladder. Knowing these factors, nursing administrators can plan their programs to support their managers in transition. (SSH)

  19. Waste Reduction Model

    Science.gov (United States)

    To help solid waste planners and organizations track/report GHG emissions reductions from various waste management practices. To assist in calculating GHG emissions of baseline and alternative waste management practices and provide the history of WARM.

  20. Hazardous Waste Generators

    Data.gov (United States)

    Vermont Center for Geographic Information — The HazWaste database contains generator (companies and/or individuals) site and mailing address information, waste generation, the amount of waste generated etc. of...

  1. The temporality of waste

    DEFF Research Database (Denmark)

    Madsen, Katrine Dahl; Jordt Jørgensen, Nanna; Læssøe, Jeppe

    Waste is, indisputably, one of the key issues of environmental concerns of our times. In an environment and sustainability education perspective, waste offers concrete entry points to issues of consumption, sustainability and citizenship. Still, waste education has received relatively little...

  2. Household hazardous waste

    DEFF Research Database (Denmark)

    Fjelsted, Lotte; Christensen, Thomas Højlund

    2007-01-01

    .) comprised 15-25% and foreign items comprised 10-20%. Water-based paint was the dominant part of the paint waste. The chemical composition of the paint waste and the paint-like waste was characterized by an analysis of 27 substances in seven waste fractions. The content of critical substances was tow......'Paint waste', a part of the 'household hazardous waste', amounting to approximately 5 tonnes was collected from recycling stations in two Danish cities. Sorting and analyses of the waste showed paint waste comprised approximately 65% of the mass, paint-like waste (cleaners, fillers, etc...... and the paint waste was less contaminated with heavy metals than was the ordinary household waste. This may suggest that households no longer need to source-segregate their paint if the household waste is incinerated, since the presence of a small quantity of solvent-based paint will not be harmful when...

  3. Informative document waste plastics

    NARCIS (Netherlands)

    Nagelhout D; Sein AA; Duvoort GL

    1989-01-01

    This "Informative document waste plastics" forms part of a series of "informative documents waste materials". These documents are conducted by RIVM on the indstruction of the Directorate General for the Environment, Waste Materials Directorate, in behalf of the program of

  4. Informative document packaging waste

    NARCIS (Netherlands)

    Joosten JM; Nagelhout D; Duvoort GL; Weerd M de

    1989-01-01

    This "informative document packaging waste" forms part of a series of "informative documents waste materials". These documents are conducted by RIVM on the instructions of the Direcotrate General for the Environment, Waste Materials Directorate, in behalf of the program of

  5. Municipal Solid Waste Management

    OpenAIRE

    Soni, Ajaykumar; Patil, Deepak; Argade, Kuldeep

    2016-01-01

    Waste management covers newly generated waste or waste from an onging process. When steps to reduce or even eliminate waste are to be considered, it is imperative that considerations should include total oversight, technical and management services of the total process.From raw material to the final product this includes technical project management expertise, technical project review and pollution prevention technical support and advocacy.Waste management also includes handling of waste, in...

  6. Supermarket food waste

    OpenAIRE

    Eriksson, Mattias

    2015-01-01

    Food waste occurs along the entire food supply chain and gives rise to great financial losses and waste of natural resources. The retail stage of the supply chain contributes significant masses of waste. Causes of this waste need to be identified before potential waste reduction measures can be designed, tested and evaluated. Therefore this thesis quantified retail food waste and evaluated selected prevention and valorisation measures, in order to determine how the carbon footprint of food ca...

  7. Purge water minimization at LEHR

    Energy Technology Data Exchange (ETDEWEB)

    Schalla, R.

    1996-11-01

    The field demonstration described in this report is being conducted as part of the Environmental Restoration Program at the Laboratory for Energy-Related Health Research (LEHR). The Environmental Restoration Program is one of several U.S. Department of Energy (DOE) waste cleanup projects designed to support by the actual use of emerging environmental management and restoration technologies. As part of an ongoing technical support mission to achieve excellence and efficiency in environmental restoration activities at LEHR, DOE requested Pacific Northwest National Laboratory`s (PNNL`s) guidance to identify the most efficient way of reducing purge water extracted by sampling pumps while still obtaining representative samples from LEHR monitoring wells.

  8. Waste Handeling Building Conceptual Study

    Energy Technology Data Exchange (ETDEWEB)

    G.W. Rowe

    2000-11-06

    The objective of the ''Waste Handling Building Conceptual Study'' is to develop proposed design requirements for the repository Waste Handling System in sufficient detail to allow the surface facility design to proceed to the License Application effort if the proposed requirements are approved by DOE. Proposed requirements were developed to further refine waste handling facility performance characteristics and design constraints with an emphasis on supporting modular construction, minimizing fuel inventory, and optimizing facility maintainability and dry handling operations. To meet this objective, this study attempts to provide an alternative design to the Site Recommendation design that is flexible, simple, reliable, and can be constructed in phases. The design concept will be input to the ''Modular Design/Construction and Operation Options Report'', which will address the overall program objectives and direction, including options and issues associated with transportation, the subsurface facility, and Total System Life Cycle Cost. This study (herein) is limited to the Waste Handling System and associated fuel staging system.

  9. Minimalism and the Pragmatic Frame

    Directory of Open Access Journals (Sweden)

    Ana Falcato

    2016-02-01

    Full Text Available In the debate between literalism and contextualism in semantics, Kent Bach’s project is often taken to stand on the latter side of the divide. In this paper I argue this is a misleading assumption and justify it by contrasting Bach’s assessment of the theoretical eliminability of minimal propositions arguably expressed by well-formed sentences with standard minimalist views, and by further contrasting his account of the division of interpretative processes ascribable to the semantics and pragmatics of a language with a parallel analysis carried out by the most radical opponent to semantic minimalism, i.e., by occasionalism. If my analysis proves right, the sum of its conclusions amounts to a refusal of Bach’s main dichotomies.

  10. Minimal universal quantum heat machine

    Science.gov (United States)

    Gelbwaser-Klimovsky, D.; Alicki, R.; Kurizki, G.

    2013-01-01

    In traditional thermodynamics the Carnot cycle yields the ideal performance bound of heat engines and refrigerators. We propose and analyze a minimal model of a heat machine that can play a similar role in quantum regimes. The minimal model consists of a single two-level system with periodically modulated energy splitting that is permanently, weakly, coupled to two spectrally separated heat baths at different temperatures. The equation of motion allows us to compute the stationary power and heat currents in the machine consistent with the second law of thermodynamics. This dual-purpose machine can act as either an engine or a refrigerator (heat pump) depending on the modulation rate. In both modes of operation, the maximal Carnot efficiency is reached at zero power. We study the conditions for finite-time optimal performance for several variants of the model. Possible realizations of the model are discussed.

  11. Green conversion of municipal solid wastes into fuels and chemicals

    Directory of Open Access Journals (Sweden)

    Leonidas Matsakas

    2017-03-01

    Full Text Available Presently, the society is facing a serious challenge for the effective management of the increasing amount of produced municipal solid wastes. The accumulated waste has caused a series of environmental problems such as uncontrolled release of greenhouse gases. Moreover, the increasing amount of wastes has resulted in a shortage of areas available for waste disposal, resulting in a nonsustainable waste management. These problems led to serious public concerns, which in turn resulted in political actions aiming to reduce the amount of wastes reaching the environment. These actions aim to promote sustainable waste management solutions. The main objective of these policies is to promote the recycling of municipal solid waste and the conversion of waste to energy and valuable chemicals. These conversions can be performed using either biological (e.g., anaerobic digestion or thermochemical processes (e.g., pyrolysis. Research efforts during the last years have been fruitful, and many publications demonstrated the effective conversation of municipal solid waste to energy and chemicals. These processes are discussed in the current review article together with the change of the waste policy that was implemented in the EU during the last years.

  12. Sustainable Materials Management (SMM) WasteWise Data

    Science.gov (United States)

    EPA??s WasteWise encourages organizations and businesses to achieve sustainability in their practices and reduce select industrial wastes. WasteWise is part of EPA??s sustainable materials management efforts, which promote the use and reuse of materials more productively over their entire lifecycles. All U.S. businesses, governments and nonprofit organizations can join WasteWise as a partner, endorser or both. Current participants range from small local governments and nonprofit organizations to large multinational corporations. Partners demonstrate how they reduce waste, practice environmental stewardship and incorporate sustainable materials management into their waste-handling processes. Endorsers promote enrollment in WasteWise as part of a comprehensive approach to help their stakeholders realize the economic benefits to reducing waste. WasteWise helps organizations reduce their impact on global climate change through waste reduction. Every stage of a product's life cycle??extraction, manufacturing, distribution, use and disposal??indirectly or directly contributes to the concentration of greenhouse gases (GHGs) in the atmosphere and affects the global climate. WasteWise is part of EPA's larger SMM program (https://www.epa.gov/smm). Sustainable Materials Management (SMM) is a systemic approach to using and reusing materials more productively over their entire lifecycles. It represents a change in how our society thinks about the use of natural resources

  13. Waste Transfer Stations

    DEFF Research Database (Denmark)

    Christensen, Thomas Højlund

    2011-01-01

    tion and transport is usually the most costly part of any waste management system; and when waste is transported over a considerable distance or for a long time, transferring the waste from the collection vehicles to more efficient transportation may be economically beneficial. This involves...... a transfer station where the transfer takes place. These stations may also be accessible by private people, offering flexibility to the waste system, including facilities for bulky waste, household hazardous waste and recyclables. Waste transfer may also take place on the collection route from small...... describes the main features of waste transfer stations, including some considerations about the economical aspects on when transfer is advisable....

  14. Economic and environmental optimization of waste treatment

    DEFF Research Database (Denmark)

    Münster, Marie; Ravn, Hans; Hedegaard, Karsten

    2015-01-01

    with different assumptions regarding displaced electricity production. The article shows that it is feasible to combine LCA methodology with optimization. Furthermore, it highlights the need for including the integrated waste and energy system into the model. © 2014 Elsevier Ltd. All rights reserved.......This article presents the new systems engineering optimization model, OptiWaste, which incorporates a life cycle assessment (LCA) methodology and captures important characteristics of waste management systems. As part of the optimization, the model identifies the most attractive waste management...... options. The model renders it possible to apply different optimization objectives such as minimizing costs or greenhouse gas emissions or to prioritize several objectives given different weights. A simple illustrative case is analysed, covering alternative treatments of one tonne of residual household...

  15. Recycling of solid wastes at kindergartens centers

    Directory of Open Access Journals (Sweden)

    Mohamed R.M.S.R.

    2017-02-01

    Full Text Available The present study aimed to conduct an activity on environmental awareness campaign at a kindergarten center, with the children age 4-6 years old. The activity included identify the various types of waste generated at the kindergarten and to realize the conservation practice by participating in simple waste management strategies and an explanation about recycling, reusing and reducing waste (3R. The activity provided the children more awareness about the importance of minimizing the plastic wastes. The activity had created an interesting experience to the young generation through practice activity and has given a light on the nature conservation along their growing years. It can be concluded that the awareness of environmental issues among children have risen up as noted by looking at students physical expression. Children have understood the potential to conserve nature from a simple action which is recycling. After the activity, children’s were able to identify and divide the rubbish.

  16. Techno-economic feasibility of waste biorefinery

    DEFF Research Database (Denmark)

    Shahzad, Khurram; Narodoslawsky, Michael; Sagir, Muhammad

    2017-01-01

    The utilization of industrial waste streams as input materials for bio-mediated production processes constitutes a current R&D objective not only to reduce process costs at the input side but in parallel, to minimize hazardous environmental emissions. In this context, the EU-funded project ANIMPOL......-quality biodiesel, offal material and meat and bone meal (MBM). Techno-economic analysis reveals that PHA production cost varies from 1.41 €/kg to 1.64 €/kg when considering offal on the one hand as waste, or, on the other hand, accounting its market price, while calculating with fixed costs for the co...... elaborated a process for the production of polyhydroxyalkanoate (PHA) biopolymers starting from diverse waste streams of the animal processing industry. This article provides a detailed economic analysis of PHA production from this waste biorefinery concept, encompassing the utilization of low...

  17. Construction schedules slack time minimizing

    Science.gov (United States)

    Krzemiński, Michał

    2017-07-01

    The article presents two copyright models for minimizing downtime working brigades. Models have been developed for construction schedules performed using the method of work uniform. Application of flow shop models is possible and useful for the implementation of large objects, which can be divided into plots. The article also presents a condition describing gives which model should be used, as well as a brief example of optimization schedule. The optimization results confirm the legitimacy of the work on the newly-developed models.

  18. Torsional Rigidity of Minimal Submanifolds

    DEFF Research Database (Denmark)

    Markvorsen, Steen; Palmer, Vicente

    2006-01-01

    We prove explicit upper bounds for the torsional rigidity of extrinsic domains of minimal submanifolds $P^m$ in ambient Riemannian manifolds $N^n$ with a pole $p$. The upper bounds are given in terms of the torsional rigidities of corresponding Schwarz symmetrizations of the domains in warped...... for the torsional rigidity are actually attained and give conditions under which the geometric average of the stochastic mean exit time for Brownian motion at infinity is finite....

  19. Optimizing Processes to Minimize Risk

    Science.gov (United States)

    Loyd, David

    2017-01-01

    NASA, like the other hazardous industries, has suffered very catastrophic losses. Human error will likely never be completely eliminated as a factor in our failures. When you can't eliminate risk, focus on mitigating the worst consequences and recovering operations. Bolstering processes to emphasize the role of integration and problem solving is key to success. Building an effective Safety Culture bolsters skill-based performance that minimizes risk and encourages successful engagement.

  20. Chemical Waste and Allied Products.

    Science.gov (United States)

    Hung, Yung-Tse; Aziz, Hamidi Abdul; Ramli, Siti Fatihah; Yeh, Ruth Yu-Li; Liu, Lian-Huey; Huhnke, Christopher Robert

    2016-10-01

    This review of literature published in 2015 focuses on waste related to chemical and allied products. The topics cover the waste management, physicochemical treatment, aerobic granular, aerobic waste treatment, anaerobic granular, anaerobic waste treatment, chemical waste, chemical wastewater, fertilizer waste, fertilizer wastewater, pesticide wastewater, pharmaceutical wastewater, ozonation. cosmetics waste, groundwater remediation, nutrient removal, nitrification denitrification, membrane biological reactor, and pesticide waste.

  1. Minimally Invasive Heart Valve Surgery.

    Science.gov (United States)

    Bouhout, Ismail; Morgant, Marie-Catherine; Bouchard, Denis

    2017-09-01

    Minimally invasive valve surgery represents a recent and significant advance in modern heart surgery. Indeed, many less invasive approaches for both the aortic and mitral valves have been developed in the past 2 decades. These procedures were hypothesized to result in less operative trauma, which might translate into better patient outcomes. However, this clinical benefit remains controversial in the literature. The aim of this review is to discuss the evidence surrounding minimally invasive heart valve surgery in the current era. A systematic search of the literature from 2006-2016 was performed looking for articles reporting early or late outcomes after minimally invasive valve surgery. Less invasive valve surgery is safe and provides long-term surgical outcomes similar to those of standard sternotomy. In addition, these approaches result in a reduction in overall hospital length of stay and may mitigate the risk of early morbidity-mainly postoperative bleeding, transfusions, and ventilation duration. Copyright © 2017 Canadian Cardiovascular Society. Published by Elsevier Inc. All rights reserved.

  2. Transforming trash: reuse as a waste management and climate change mitigation strategy

    OpenAIRE

    Vergara, Sintana Eugenia

    2011-01-01

    Waste reflects the culture that produces it and affects the health of the people and environment surrounding it. As urbanization and waste production increase on a global scale, cities are faced with the challenge of how to manage their waste effectively to minimize its negative impacts on public and environmental health. Using waste as a resource can offer a variety of environmental benefits, including climate change mitigation, though these benefits are variable and uncertain. My work begin...

  3. Assessment for the management of NORM wastes in conventional hazardous and nonhazardous waste landfills

    Energy Technology Data Exchange (ETDEWEB)

    Mora, Juan C., E-mail: jc.mora@ciemat.es [Unit for Radiation Protection of the Public and the Environment (PRPYMA), CIEMAT, Avda. Complutense, 40, 28040 Madrid (Spain); Energy Engineering Department, Power Engineering, Nuclear Area, ETSII, UNED (Spain); Baeza, Antonio [LARUEX, Dpt. Applied Physics, Faculty of Veterinary Science, University of Extremadura, Avda. Universidad, s/n, 10071 Cáceres (Spain); Robles, Beatriz [Unit for Radiation Protection of the Public and the Environment (PRPYMA), CIEMAT, Avda. Complutense, 40, 28040 Madrid (Spain); Sanz, Javier [Energy Engineering Department, Power Engineering, Nuclear Area, ETSII, UNED (Spain)

    2016-06-05

    Highlights: • Before 2010 NORM waste is managed as non-radioactive, disposed in landfills. • After 2010 radiological impact of the management of NORM wastes must be assessed. • Quantities that can be disposed in hazardous or non-hazardous landfills are given. • Uncertainty analysis is included to provide consistency to the calculations. - Abstract: Naturally Occurring Radioactive Materials (NORM) wastes are generated in huge quantities in several industries and their management has been carried out under considerations of industrial non-radioactive wastes, before the concern on the radioactivity content was included in the legislation. Therefore these wastes were conditioned using conventional methods and the waste disposals were designed to isolate toxic elements from the environment for long periods of time. Spanish regulation for these conventional toxic waste disposals includes conditions that assure adequate isolation to minimize the impact of the wastes to the environment in present and future conditions. After 1996 the radiological impact of the management of NORM wastes is considered and all the aspects related with natural radiations and the radiological control regarding the management of residues from NORM industries were developed in the new regulation. One option to be assessed is the disposal of NORM wastes in hazardous and non-hazardous waste disposals, as was done before this new regulation. This work analyses the management of NORM wastes in these landfills to derive the masses that can be disposed without considerable radiological impact. Generic dose assessments were carried out under highly conservative hypothesis and a discussion on the uncertainty and variability sources was included to provide consistency to the calculations.

  4. Minimally invasive total knee arthroplasty.

    Science.gov (United States)

    Bonutti, Peter M; Mont, Michael A; McMahon, Margo; Ragland, Phillip S; Kester, Mark

    2004-01-01

    Currently, minimally invasive total knee arthroplasty is defined as an incision length of definition are: 1. The amount of soft-tissue dissection (including muscle, ligament, and capsular damage). 2. Patellar retraction or eversion. 3. Tibiofemoral dislocation. Minimally invasive surgery should not be considered to be a cosmetic procedure but rather one that addresses patients' concerns with regard to postoperative pain and slow rehabilitation. Standard total knee arthroplasties provide pain relief, but returning to activities of daily living remains a challenge for some individuals, who may take several weeks to recover. Several studies have demonstrated long-term success (at more than ten years) of standard total knee arthroplasties. However, many patients remain unsatisfied with the results of the surgery. In a study of functional limitations of patients with a Knee Society score of > or = 90 points after total knee arthroplasty, only 35% of patients stated that they had no limitations. This finding was highlighted in a study by Dickstein et al., in which one-third of the elderly patients who underwent knee replacement were unhappy with the outcome at six and twelve months postoperatively. Although many surgeons utilize objective functional scoring systems to evaluate outcome, it is likely that the criteria for a successful result of total knee arthroplasty differ between the patient and the surgeon. This was evident in a report by Bullens et al., who concluded that surgeons are more satisfied with the results of total knee arthroplasty than are their patients. Trousdale et al. showed that, in addition to concerns about long-term functional outcome, patients' major concerns were postoperative pain and the time required for recovery. Patients undergoing total knee arthroplasty have specific functional goals, such as climbing stairs, squatting, kneeling, and returning to some level of low-impact sports after surgery. Our clinical investigations demonstrated that

  5. Introduction to Waste Management

    DEFF Research Database (Denmark)

    Christensen, Thomas Højlund

    2011-01-01

    Solid waste management is as old as human civilization, although only considered an engineering discipline for about one century. The change from the previous focus on public cleansing of the cities to modern waste management was primarily driven by industrialization, which introduced new materials...... and chemicals, dramatically changing the types and composition of waste, and by urbanization making waste management in urban areas a complicated and costly logistic operation. This book focuses on waste that commonly appears in the municipal waste management system. This chapter gives an introduction to modern...... waste management, including issues as waste definition, problems associated with waste, waste management criteria and approaches to waste management. Later chapters introduce aspects of engineering (Chapter 1.2), economics (Chapter 1.3) and regulation (Chapter 1.4)....

  6. Preliminary experimental studies of waste coal gasification

    Energy Technology Data Exchange (ETDEWEB)

    Su, S.; Jin, Y.G.; Yu, X.X.; Worrall, R. [CSIRO, Brisbane, QLD (Australia). Advanced Coal Technology

    2013-07-01

    Coal mining is one of Australia's most important industries. It was estimated that coal washery rejects from black coal mining was approximately 1.82 billion tonnes from 1960 to 2009 in Australia, and is projected to produce another one billion tonnes by 2018 at the current production rate. To ensure sustainability of the Australian coal industry, we have explored a new potential pathway to create value from the coal waste through production of liquid fuels or power generation using produced syngas from waste coal gasification. Consequently, environmental and community impacts of the solid waste could be minimized. However, the development of an effective waste coal gasification process is a key to the new pathway. An Australian mine site with a large reserve of waste coal was selected for the study, where raw waste coal samples including coarse rejects and tailings were collected. After investigating the initial raw waste coal samples, float/sink testing was conducted to achieve a desired ash target for laboratory-scale steam gasification testing and performance evaluation. The preliminary gasification test results show that carbon conversions of waste coal gradually increase as the reaction proceeds, which indicates that waste coal can be gasified by a steam gasification process. However, the carbon conversion rates are relatively low, only reaching to 20-30%. Furthermore, the reactivity of waste coal samples with a variety of ash contents under N{sub 2}/air atmosphere have been studied by a home-made thermogravimetric analysis (TGA) apparatus that can make the sample reach the reaction temperature instantly.

  7. Thirteenth annual U.S. DOE low-level radioactive waste management conference: Proceedings

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1991-12-31

    The 40 papers in this document comprise the proceedings of the Department of Energy`s Thirteenth Annual Low-Level Radioactive Waste Management Conference that was held in Atlanta, Georgia, on November 19--21, 1991. General subjects addressed during the conference included: disposal facility design; greater-than-class C low-level waste; public acceptance considerations; waste certification; site characterization; performance assessment; licensing and documentation; emerging low-level waste technologies; waste minimization; mixed waste; tracking and transportation; storage; and regulatory changes. Papers have been processed separately for inclusion on the data base.

  8. Letter report: Minor component study for low-level radioactive waste glasses

    Energy Technology Data Exchange (ETDEWEB)

    Li, H.

    1996-03-01

    During the waste vitrification process, troublesome minor components in low-level radioactive waste streams could adversely affect either waste vitrification rate or melter life-time. Knowing the solubility limits for these minor components is important to determine pretreatment options for waste streams and glass formulation to prevent or to minimize these problems during the waste vitrification. A joint study between Pacific Northwest Laboratory and Rensselaer Polytechnic Institute has been conducted to determine minor component impacts in low-level nuclear waste glass.

  9. Metazoan promoters

    DEFF Research Database (Denmark)

    Lenhard, Boris; Sandelin, Albin Gustav; Carninci, Piero

    2012-01-01

    Promoters are crucial for gene regulation. They vary greatly in terms of associated regulatory elements, sequence motifs, the choice of transcription start sites and other features. Several technologies that harness next-generation sequencing have enabled recent advances in identifying promoters ...

  10. Simulation analysis of wastes gasification technologies

    Directory of Open Access Journals (Sweden)

    Stępień Leszek

    2017-01-01

    Full Text Available Each year a significant growth in the amount of wastes generated is observed. Due to this fact technologies enabling utilization of wastes are needed. One of the ways to utilizes wastes is thermal conversion. Most widely used technology for thermal conversion is gasification that enables to produce syngas that can be either combusted or directed to further synthesis to produce methanol or liquid fuels. There are several commercially available technologies that enable to gasify wastes. The first part of this study is subjected to general description of waste gasification process. Furthermore the analysis and comparison of commercially available gasification technologies is presented, including their process arrangement, limits and capabilities. Second part of the study is dedicated to the development of thermodynamic model for waste gasification. The model includes three zones of gasification reactors: drying, gasification and eventually ash melting. Modified Gibbs minimization method is used to simulate gasification process. The model is capable of predicting final gas composition as a function of temperature or equivalence ratio. Calculations are performed for a specified average wastes composition and different equivalence ratios of air to discuss its influence on the performance of gasification (temperature of the process and gas composition. Finally the model enables to calculate total energy balance of the process as well as gasification and final gas temperature.

  11. Health Promotion

    DEFF Research Database (Denmark)

    Povlsen, Lene; Borup, I.

    2015-01-01

    In 1953 when the Nordic School of Public Health was founded, the aim of public health programmes was disease prevention more than health promotion. This was not unusual, since at this time health usually was seen as the opposite of disease and illness. However, with the Ottawa Charter of 1986......, the World Health Organization made a crucial change to view health not as a goal in itself but as the means to a full life. In this way, health promotion became a first priority and fundamental action for the modern society. This insight eventually reached NHV and in 2002 - 50 years after the foundation...... - an associate professorship was established with a focus on health promotion. Nevertheless, the concept of health promotion had been integrated with or mentioned in courses run prior to the new post. Subsequently, a wide spectrum of courses in health promotion was introduced, such as Empowerment for Child...

  12. Waste to Energy: Challenges and Opportunities in Iran

    Directory of Open Access Journals (Sweden)

    Lida Rafati

    2016-12-01

    Conclusion: This study recommends construction of incineration plants with an appropriate location for processing municipal, household, and industrial hazardous wastes, as well as energy recovery. In addition, promoting application of household biogas reservoirs in villages and use of pyrolysis for some industries to converse industrial waste into fuel, are further suggested.

  13. Minimal families of curves on surfaces

    KAUST Repository

    Lubbes, Niels

    2014-11-01

    A minimal family of curves on an embedded surface is defined as a 1-dimensional family of rational curves of minimal degree, which cover the surface. We classify such minimal families using constructive methods. This allows us to compute the minimal families of a given surface.The classification of minimal families of curves can be reduced to the classification of minimal families which cover weak Del Pezzo surfaces. We classify the minimal families of weak Del Pezzo surfaces and present a table with the number of minimal families of each weak Del Pezzo surface up to Weyl equivalence.As an application of this classification we generalize some results of Schicho. We classify algebraic surfaces that carry a family of conics. We determine the minimal lexicographic degree for the parametrization of a surface that carries at least 2 minimal families. © 2014 Elsevier B.V.

  14. Hanford Site annual dangerous waste report: Volume 3, Part 1, Waste Management Facility report, dangerous waste

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-12-31

    This report contains information on hazardous wastes at the Hanford Site. Information consists of shipment date, physical state, chemical nature, waste description, handling method and containment vessel, waste number, waste designation, and amount of waste.

  15. Hanford Site annual dangerous waste report: Volume 3, Part 2, Waste Management Facility report, dangerous waste

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1944-12-31

    This report contains information on hazardous wastes at the Hanford Site. Information consists of shipment date, physical state, chemical nature, waste description, handling and containment vessel, waste number, waste designation and amount of waste.

  16. About the ZOOM minimization package

    Energy Technology Data Exchange (ETDEWEB)

    Fischler, M.; Sachs, D.; /Fermilab

    2004-11-01

    A new object-oriented Minimization package is available for distribution in the same manner as CLHEP. This package, designed for use in HEP applications, has all the capabilities of Minuit, but is a re-write from scratch, adhering to modern C++ design principles. A primary goal of this package is extensibility in several directions, so that its capabilities can be kept fresh with as little maintenance effort as possible. This package is distinguished by the priority that was assigned to C++ design issues, and the focus on producing an extensible system that will resist becoming obsolete.

  17. 75 FR 61356 - Hazardous Waste Management System; Identification and Listing of Hazardous Waste; Correction

    Science.gov (United States)

    2010-10-05

    ... correcting the arsenic value limit and correcting it in Table 1 of appendix IX to part 261--Waste Excluded... rule, EPA has taken the necessary steps to eliminate drafting errors and ambiguity, minimize potential...: Authority: 42 U.S.C. 6905, 6912(a), 6921, 6922, and 6938. 0 2. In Tables 1 of Appendix IX to Part 261 revise...

  18. Economic analysis of waste-to-energy industry in China.

    Science.gov (United States)

    Zhao, Xin-Gang; Jiang, Gui-Wu; Li, Ang; Wang, Ling

    2016-02-01

    The generation of municipal solid waste is further increasing in China with urbanization and improvement of living standards. The "12th five-year plan" period (2011-2015) promotes waste-to-energy technologies for the harmless disposal and recycling of municipal solid waste. Waste-to-energy plant plays an important role for reaching China's energy conservation and emission reduction targets. Industrial policies and market prospect of waste-to-energy industry are described. Technology, cost and benefit of waste-to-energy plant are also discussed. Based on an economic analysis of a waste-to-energy project in China (Return on Investment, Net Present Value, Internal Rate of Return, and Sensitivity Analysis) the paper makes the conclusions. Copyright © 2015 Elsevier Ltd. All rights reserved.

  19. Current trends of tropical fruit waste utilization.

    Science.gov (United States)

    Cheok, Choon Yoong; Mohd Adzahan, Noranizan; Abdul Rahman, Russly; Zainal Abedin, Nur Hanani; Hussain, Norhayati; Sulaiman, Rabiha; Chong, Gun Hean

    2018-02-11

    Recent rapid growth of the world's population has increased food demands. This phenomenon poses a great challenge for food manufacturers in maximizing the existing food or plant resources. Nowadays, the recovery of health benefit bioactive compounds from fruit wastes is a research trend not only to help minimize the waste burden, but also to meet the intensive demand from the public for phenolic compounds which are believed to have protective effects against chronic diseases. This review is focused on polyphenolic compounds recovery from tropical fruit wastes and its current trend of utilization. The tropical fruit wastes include in discussion are durian (Durio zibethinus), mangosteen (Garcinia mangostana L.), rambutan (Nephelium lappaceum), mango (Mangifera indica L.), jackfruit (Artocarpus heterophyllus), papaya (Carica papaya), passion fruit (Passiflora edulis), dragon fruit (Hylocereus spp), and pineapple (Ananas comosus). Highlights of bioactive compounds in different parts of a tropical fruit are targeted primarily for food industries as pragmatic references to create novel innovative health enhancement food products. This information is intended to inspire further research ideas in areas that are still under-explored and for food processing manufacturers who would like to minimize wastes as the norm of present day industry (design) objective.

  20. Estimation of construction waste generation and management in Thailand.

    Science.gov (United States)

    Kofoworola, Oyeshola Femi; Gheewala, Shabbir H

    2009-02-01

    This study examines construction waste generation and management in Thailand. It is estimated that between 2002 and 2005, an average of 1.1 million tons of construction waste was generated per year in Thailand. This constitutes about 7.7% of the total amount of waste disposed in both landfills and open dumpsites annually during the same period. Although construction waste constitutes a major source of waste in terms of volume and weight, its management and recycling are yet to be effectively practiced in Thailand. Recently, the management of construction waste is being given attention due to its rapidly increasing unregulated dumping in undesignated areas, and recycling is being promoted as a method of managing this waste. If effectively implemented, its potential economic and social benefits are immense. It was estimated that between 70 and 4,000 jobs would have been created between 2002 and 2005, if all construction wastes in Thailand had been recycled. Additionally it would have contributed an average savings of about 3.0 x 10(5) GJ per year in the final energy consumed by the construction sector of the nation within the same period based on the recycling scenario analyzed. The current national integrated waste management plan could enhance the effective recycling of construction and demolition waste in Thailand when enforced. It is recommended that an inventory of all construction waste generated in the country be carried out in order to assess the feasibility of large scale recycling of construction and demolition waste.

  1. Waste Package Lifting Calculation

    Energy Technology Data Exchange (ETDEWEB)

    H. Marr

    2000-05-11

    The objective of this calculation is to evaluate the structural response of the waste package during the horizontal and vertical lifting operations in order to support the waste package lifting feature design. The scope of this calculation includes the evaluation of the 21 PWR UCF (pressurized water reactor uncanistered fuel) waste package, naval waste package, 5 DHLW/DOE SNF (defense high-level waste/Department of Energy spent nuclear fuel)--short waste package, and 44 BWR (boiling water reactor) UCF waste package. Procedure AP-3.12Q, Revision 0, ICN 0, calculations, is used to develop and document this calculation.

  2. Commercial and Institutional Waste

    DEFF Research Database (Denmark)

    Christensen, Thomas Højlund; Fruergaard, Thilde

    2011-01-01

    Commercial and institutional waste is primarily from retail (stores), hotels, restaurants, health care (except health risk waste), banks, insurance companies, education, retirement homes, public services and transport. Within some of these sectors, e.g. retail and restaurants, large variations...... is handled in the municipal waste system, where information is easily accessible. An important part of commercial and institutional waste is packaging waste, and enterprises with large quantities of clean paper, cardboard and plastic waste may have their own facilities for baling and storing their waste...

  3. Understanding radioactive waste

    Energy Technology Data Exchange (ETDEWEB)

    Murray, R.L.

    1981-12-01

    This document contains information on all aspects of radioactive wastes. Facts are presented about radioactive wastes simply, clearly and in an unbiased manner which makes the information readily accessible to the interested public. The contents are as follows: questions and concerns about wastes; atoms and chemistry; radioactivity; kinds of radiation; biological effects of radiation; radiation standards and protection; fission and fission products; the Manhattan Project; defense and development; uses of isotopes and radiation; classification of wastes; spent fuels from nuclear reactors; storage of spent fuel; reprocessing, recycling, and resources; uranium mill tailings; low-level wastes; transportation; methods of handling high-level nuclear wastes; project salt vault; multiple barrier approach; research on waste isolation; legal requiremnts; the national waste management program; societal aspects of radioactive wastes; perspectives; glossary; appendix A (scientific American articles); appendix B (reference material on wastes). (ATT)

  4. Next-to-minimal SOFTSUSY

    Science.gov (United States)

    Allanach, B. C.; Athron, P.; Tunstall, Lewis C.; Voigt, A.; Williams, A. G.

    2014-09-01

    We describe an extension to the SOFTSUSY program that provides for the calculation of the sparticle spectrum in the Next-to-Minimal Supersymmetric Standard Model (NMSSM), where a chiral superfield that is a singlet of the Standard Model gauge group is added to the Minimal Supersymmetric Standard Model (MSSM) fields. Often, a Z3 symmetry is imposed upon the model. SOFTSUSY can calculate the spectrum in this case as well as the case where general Z3 violating (denoted as =) terms are added to the soft supersymmetry breaking terms and the superpotential. The user provides a theoretical boundary condition for the couplings and mass terms of the singlet. Radiative electroweak symmetry breaking data along with electroweak and CKM matrix data are used as weak-scale boundary conditions. The renormalisation group equations are solved numerically between the weak scale and a high energy scale using a nested iterative algorithm. This paper serves as a manual to the NMSSM mode of the program, detailing the approximations and conventions used. Catalogue identifier: ADPM_v4_0 Program summary URL:http://cpc.cs.qub.ac.uk/summaries/ADPM_v4_0.html Program obtainable from: CPC Program Library, Queen's University, Belfast, N. Ireland Licensing provisions: Standard CPC licence, http://cpc.cs.qub.ac.uk/licence/licence.html No. of lines in distributed program, including test data, etc.: 154886 No. of bytes in distributed program, including test data, etc.: 1870890 Distribution format: tar.gz Programming language: C++, fortran. Computer: Personal computer. Operating system: Tested on Linux 3.x. Word size: 64 bits Classification: 11.1, 11.6. Does the new version supersede the previous version?: Yes Catalogue identifier of previous version: ADPM_v3_0 Journal reference of previous version: Comput. Phys. Comm. 183 (2012) 785 Nature of problem: Calculating supersymmetric particle spectrum and mixing parameters in the next-to-minimal supersymmetric standard model. The solution to the

  5. Iron Phosphate Glasses: An Alternative for Vitrifying Certain Nuclear Wastes

    Energy Technology Data Exchange (ETDEWEB)

    Delbert E. Day; Chandra S. Ray; Cheol-Woon Kim

    2004-12-28

    Vitrification of nuclear waste in a glass is currently the preferred process for waste disposal. DOE currently approves only borosilicate (BS) type glasses for such purposes. However, many nuclear wastes, presently awaiting disposal, have complex and diverse chemical compositions, and often contain components that are poorly soluble or chemically incompatible in BS glasses. Such problematic wastes can be pre-processed and/or diluted to compensate for their incompatibility with a BS glass matrix, but both of these solutions increases the wasteform volume and the overall cost for vitrification. Direct vitrification using alternative glasses that utilize the major components already present in the waste is preferable, since it avoids pre-treating or diluting the waste, and, thus, minimizes the wasteform volume and overall cost.

  6. Joint optimisation of the future Danish waste and energy system

    DEFF Research Database (Denmark)

    Münster, Marie; Pizarro, Amalia Rosa; Salvucci, Raffaele

    2015-01-01

    In this article the impact of the future development of the energy system on the feasibility of waste treatment options is analysed. In the article two different optimization tools are used: a regional electricity model (Balmorel) and a national waste treatment and district heating model (OptiWaste......). When performing optimization by minimizing the socio-economic costs, into future energy systems with high wind power production, it proves feasible primarily to incinerate waste in large scale combined heat and power (CHP) plants, whereas more incineration takes place in decentralized CHP plants...... in future scenarios with higher biomass consumption, where the average heat prices are higher. In both scenarios, biogas produced from organic waste is upgraded and fed into the natural gas grid and waste is incinerated rather than being centrally sorted in a material recovery facility....

  7. Nuclear waste solidification

    Science.gov (United States)

    Bjorklund, William J.

    1977-01-01

    High level liquid waste solidification is achieved on a continuous basis by atomizing the liquid waste and introducing the atomized liquid waste into a reaction chamber including a fluidized, heated inert bed to effect calcination of the atomized waste and removal of the calcined waste by overflow removal and by attrition and elutriation from the reaction chamber, and feeding additional inert bed particles to the fluidized bed to maintain the inert bed composition.

  8. for the Waste Water Cleaning Plant

    Directory of Open Access Journals (Sweden)

    E. V. Grigorieva

    2010-01-01

    Full Text Available A model of a waste water treatment plant is investigated. The model is described by a nonlinear system of two differential equations with one bounded control. An optimal control problem of minimizing concentration of the polluted water on the given time interval is stated and solved analytically with the use of the Pontryagin Maximum Principle and Green's Theorem. Computer simulations of a model of an industrial waste water treatment plant show the advantage of using our optimal strategy. Possible applications are discussed.

  9. Laparoscopic colonic resection in inflammatory bowel disease: minimal surgery, minimal access and minimal hospital stay.

    LENUS (Irish Health Repository)

    Boyle, E

    2008-11-01

    Laparoscopic surgery for inflammatory bowel disease (IBD) is technically demanding but can offer improved short-term outcomes. The introduction of minimally invasive surgery (MIS) as the default operative approach for IBD, however, may have inherent learning curve-associated disadvantages. We hypothesise that the establishment of MIS as the standard operative approach does not increase patient morbidity as assessed in the initial period of its introduction into a specialised unit, and that it confers earlier postoperative gastrointestinal recovery and reduced hospitalisation compared with conventional open resection.

  10. E-waste Management and Refurbishment Prediction (EMARP) Model for Refurbishment Industries.

    Science.gov (United States)

    Resmi, N G; Fasila, K A

    2017-10-01

    This paper proposes a novel algorithm for establishing a standard methodology to manage and refurbish e-waste called E-waste Management And Refurbishment Prediction (EMARP), which can be adapted by refurbishing industries in order to improve their performance. Waste management, particularly, e-waste management is a serious issue nowadays. Computerization has been into waste management in different ways. Much of the computerization has happened in planning the waste collection, recycling and disposal process and also managing documents and reports related to waste management. This paper proposes a computerized model to make predictions for e-waste refurbishment. All possibilities for reusing the common components among the collected e-waste samples are predicted, thus minimizing the wastage. Simulation of the model has been done to analyse the accuracy in the predictions made by the system. The model can be scaled to accommodate the real-world scenario. Copyright © 2017 Elsevier Ltd. All rights reserved.

  11. Solid Waste Management Practices of Select State Universities in CALABARZON, Philippines

    Directory of Open Access Journals (Sweden)

    Amado C. Gequinto

    2017-02-01

    Full Text Available The enactment of the Ecological Solid Waste Management Act prompted higher education institutions including state universities and colleges (SUCs to incorporate ecological waste management in the school system. Thus, this paper aimed to assess the extent of implementation of solid waste management practices in select SUCs in CALABARZON in terms of waste reuse, waste reduction, waste collection, waste recycling, waste treatment, and final waste disposal. Respondents of the study included university administrators, faculty members, non-teaching staff, students and concessionaries for a total of 341. A survey questionnaire was used to gather data from Batangas State University (BatState-U, Cavite State University (CavSU, Laguna State Polytechnic University (LSPU and Southern Luzon State University (SLSU. Result revealed that solid waste management practices are implemented to a great extent. Among the practices, waste collection got the highest composite mean particularly on the promotion of 3Rs (reduce, reuse, recycle in the collection of waste. On the other hand, waste recycling and waste treatment obtained the lowest composite mean. In terms of waste recycling, establishing partnership with local or private business for recyclable recovery program was to moderate extent. Waste treatment particularly neutralization of acid bases was also of moderate extent. The study recommended strengthening of publicprivate partnership (PPP on the recycling and treatment of wastes.

  12. Seminar on waste treatment and disposal

    Energy Technology Data Exchange (ETDEWEB)

    Sneve, Malgorzata Karpow; Snihs, Jan Olof

    1999-07-01

    Leading abstract. A seminar on radioactive waste treatment and disposal was held 9 - 14 November 1998 in Oskarshamn, Sweden. The objective of the seminar was to exchange information on national and international procedures, practices and requirements for waste management. This information exchange was intended to promote the development of a suitable strategy for management of radioactive waste in Northwest Russia to be used as background for future co-operation in the region. The seminar focused on (1) overviews of international co-operation in the waste management field and national systems for waste management, (2) experiences from treatment of low- and intermediate-level radioactive waste, (3) the process of determining the options for final disposal of radioactive waste, (4) experiences from performance assessments and safety analysis for repositories intended for low- and intermediate level radioactive waste, (5) safety of storage and disposal of high-level waste. The seminar was jointly organised and sponsored by the Swedish Radiation Protection Institute (SSI), the Norwegian Radiation Protection Authority (NRPA), the Nordic Nuclear Safety Research (NKS) and the European Commission. A Russian version of the report is available. In brief, the main conclusions are: (1) It is the prerogative of the Russian federal Government to devise and implement a waste management strategy without having to pay attention to the recommendations of the meeting, (2) Some participants consider that many points have already been covered in existing governmental documents, (3) Norway and Sweden would like to see a strategic plan in order to identify how and where to co-operate best, (4) There is a rigorous structure of laws in place, based on over-arching environmental laws, (5) Decommissioning of submarines is a long and complicated task, (6) There are funds and a desire for continued Norway/Sweden/Russia co-operation, (7) Good co-operation is already taking place.

  13. Brazil Low Carbon Case Study : Waste

    OpenAIRE

    World Bank

    2010-01-01

    This report synthesis the findings for the waste sector of a broader study, the Brazil low carbon study, which was undertaken by the World Bank in its initiative to support Brazil's integrated effort towards reducing national and global emissions of Greenhouse Gases (GHG) while promoting long term development. The purpose of the present report is to assist in the preparation of public poli...

  14. Radioactive waste disposal and public acceptance aspects

    Energy Technology Data Exchange (ETDEWEB)

    Ulhoa, Barbara M.A.; Aleixo, Bruna L.; Mourao, Rogerio P.; Ferreira, Vinicius V.M., E-mail: mouraor@cdtn.b, E-mail: vvmf@cdtn.b [Centro de Desenvolvimento da Tecnologia Nuclear (CDTN/CNEN-MG), Belo Horizonte, MG (Brazil)

    2011-07-01

    Part of the public opinion around the world considers the wastes generated due to nuclear applications as the biggest environmental problem of the present time. The development of a solution that satisfies everybody is a great challenge, in that obtaining public acceptance for nuclear enterprises is much more challenging than solving the technical issues involved. Considering that the offering of a final solution that closes the radioactive waste cycle has a potentially positive impact on public opinion, the objective of this work is to evaluate the amount of the radioactive waste volume disposed in a five-year period in several countries and gauge the public opinion regarding nuclear energy. The results show that the volume of disposed radioactive waste increased, a fact that stresses the importance of promoting discussions about repositories and public acceptance. (author)

  15. The minimal flavour violating axion

    Science.gov (United States)

    Arias-Aragón, F.; Merlo, L.

    2017-10-01

    The solution to the Strong CP problem is analysed within the Minimal Flavour Violation (MFV) context. An Abelian factor of the complete flavour symmetry of the fermionic kinetic terms may play the role of the Peccei-Quinn symmetry in traditional axion models. Its spontaneous breaking, due to the addition of a complex scalar field to the Standard Model scalar spectrum, generates the MFV axion, which may redefine away the QCD theta parameter. It differs from the traditional QCD axion for its couplings that are governed by the fermion charges under the axial Abelian symmetry. It is also distinct from the so-called Axiflavon, as the MFV axion does not describe flavour violation, while it does induce flavour non-universality effects. The MFV axion phenomenology is discussed considering astrophysical, collider and flavour data.

  16. [MINIMALLY INVASIVE AORTIC VALVE REPLACEMENT].

    Science.gov (United States)

    Tabata, Minoru

    2016-03-01

    Minimally invasive aortic valve replacement (MIAVR) is defined as aortic valve replacement avoiding full sternotomy. Common approaches include a partial sternotomy right thoracotomy, and a parasternal approach. MIAVR has been shown to have advantages over conventional AVR such as shorter length of stay and smaller amount of blood transfusion and better cosmesis. However, it is also known to have disadvantages such as longer cardiopulmonary bypass and aortic cross-clamp times and potential complications related to peripheral cannulation. Appropriate patient selection is very important. Since the procedure is more complex than conventional AVR, more intensive teamwork in the operating room is essential. Additionally, a team approach during postoperative management is critical to maximize the benefits of MIAVR.

  17. Strategies to Minimize Antibiotic Resistance

    Directory of Open Access Journals (Sweden)

    Sang Hee Lee

    2013-09-01

    Full Text Available Antibiotic resistance can be reduced by using antibiotics prudently based on guidelines of antimicrobial stewardship programs (ASPs and various data such as pharmacokinetic (PK and pharmacodynamic (PD properties of antibiotics, diagnostic testing, antimicrobial susceptibility testing (AST, clinical response, and effects on the microbiota, as well as by new antibiotic developments. The controlled use of antibiotics in food animals is another cornerstone among efforts to reduce antibiotic resistance. All major resistance-control strategies recommend education for patients, children (e.g., through schools and day care, the public, and relevant healthcare professionals (e.g., primary-care physicians, pharmacists, and medical students regarding unique features of bacterial infections and antibiotics, prudent antibiotic prescribing as a positive construct, and personal hygiene (e.g., handwashing. The problem of antibiotic resistance can be minimized only by concerted efforts of all members of society for ensuring the continued efficiency of antibiotics.

  18. Strategies to minimize antibiotic resistance.

    Science.gov (United States)

    Lee, Chang-Ro; Cho, Ill Hwan; Jeong, Byeong Chul; Lee, Sang Hee

    2013-09-12

    Antibiotic resistance can be reduced by using antibiotics prudently based on guidelines of antimicrobial stewardship programs (ASPs) and various data such as pharmacokinetic (PK) and pharmacodynamic (PD) properties of antibiotics, diagnostic testing, antimicrobial susceptibility testing (AST), clinical response, and effects on the microbiota, as well as by new antibiotic developments. The controlled use of antibiotics in food animals is another cornerstone among efforts to reduce antibiotic resistance. All major resistance-control strategies recommend education for patients, children (e.g., through schools and day care), the public, and relevant healthcare professionals (e.g., primary-care physicians, pharmacists, and medical students) regarding unique features of bacterial infections and antibiotics, prudent antibiotic prescribing as a positive construct, and personal hygiene (e.g., handwashing). The problem of antibiotic resistance can be minimized only by concerted efforts of all members of society for ensuring the continued efficiency of antibiotics.

  19. Impact assessment of waste management options in Singapore.

    Science.gov (United States)

    Tan, Reginald B H; Khoo, Hsien H

    2006-03-01

    This paper describes the application of life cycle assessment for evaluating various waste management options in Singapore, a small-island city state. The impact assessment method by SimaPro is carried out for comparing the potential environmental impacts of waste treatment options including landfilling, incineration, recycling, and composting. The inventory data include gases and leachate from landfills, air emissions and energy recovery from incinerators, energy (and emission) savings from recycling, composting gases, and transport pollution. The impact assessment results for climate change, acidification, and ecotoxicity show that the incineration of materials imposes considerable harm to both human health and the environment, especially for the burning of plastics, paper/cardboard, and ferrous metals. The results also show that, although some amount of energy can be derived from the incineration of wastes, these benefits are outweighed by the air pollution (heavy metals and dioxins/furans) that incinerators produce. For Singapore, landfill gases and leachate generate minimal environmental damage because of the nation's policy to landfill only 10% of the total disposed wastes. Land transportation and separation of waste materials also pose minimal environmental damage. However, sea transportation to the landfill could contribute significantly to acidification because of the emissions of sulfur oxides and nitrogen oxides from barges. The composting of horticultural wastes hardly imposes any environmental damage. Out of all the waste strategies, the recycling of wastes offers the best solution for environmental protection and improved human health for the nation. Significant emission savings can be realized through recycling.

  20. Low-Level Waste (LLW) forum meeting report

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-12-31

    The Low-Level Radioactive Waste Forum (LLW Forum) is an association of state and compact representatives, appointed by governors and compact commissions, established to facilitate state and compact implementation of the Low-Level Radioactive Waste Policy Act of 1980 and the Low-Level Radioactive Waste Policy Amendments Act of 1985 and to promote the objectives of low-level radioactive waste regional compacts. The LLW Forum provides an opportunity for state and compact officials to share information with one another and to exchange views with officials of federal agencies and other interested parties.

  1. Isolation and functional characterization of the human 90K promoter

    DEFF Research Database (Denmark)

    Brakebusch, C; Sures, I; Jallal, B

    1999-01-01

    90K is a secreted protein thought to be involved in the body's defense against pathogens and cancer. To elucidate its transcriptional regulation, the promoter of human 90K (HGMW-approved symbol LGAL S3BP) was isolated and characterized. Analysis of the 3. 3-kb 5'-flanking region revealed...... region around the minimal promoter (-99 --> -12) was highly homologous between human and mouse. While both human and mouse minimal promoters contained an interferon-responsive element (IRF-E), the human minimal promoter was not inducible by poly(I). poly(C) in contrast to that of the mouse. Point...... mutations 30 bp upstream of the IRF-E, however, conferred inducibility to the human minimal promoter, suggesting interaction between different promoter elements....

  2. Waste catalysts for waste polymer.

    Science.gov (United States)

    Salmiaton, A; Garforth, A

    2007-01-01

    Catalytic cracking of high-density polyethylene (HDPE) over fluid catalytic cracking (FCC) catalysts (1:6 ratio) was carried out using a laboratory fluidized bed reactor operating at 450 degrees C. Two fresh and two steam deactivated commercial FCC catalysts with different levels of rare earth oxide (REO) were compared as well as two used FCC catalysts (E-Cats) with different levels of metal poisoning. Also, inert microspheres (MS3) were used as a fluidizing agent to compare with thermal cracking process at BP pilot plant at Grangemouth, Scotland, which used sand as its fluidizing agent. The results of HDPE degradation in terms of yield of volatile hydrocarbon product are fresh FCC catalysts>steamed FCC catalysts approximately used FCC catalysts. The thermal cracking process using MS3 showed that at 450 degrees C, the product distribution gave 46 wt% wax, 14% hydrocarbon gases, 8% gasoline, 0.1% coke and 32% nonvolatile product. In general, the product yields from HDPE cracking showed that the level of metal contamination (nickel and vanadium) did not affect the product stream generated from polymer cracking. This study gives promising results as an alternative technique for the cracking and recycling of polymer waste.

  3. Hanford Waste Physical and Rheological Properties: Data and Gaps

    Energy Technology Data Exchange (ETDEWEB)

    Wells, Beric E.; Kurath, Dean E.; Mahoney, Lenna A.; Onishi, Yasuo; Huckaby, James L.; Cooley, Scott K.; Burns, Carolyn A.; Buck, Edgar C.; Tingey, Joel M.; Daniel, Richard C.; Anderson, K. K.

    2011-08-01

    The Hanford Site in Washington State manages 177 underground storage tanks containing approximately 250,000 m3 of waste generated during past defense reprocessing and waste management operations. These tanks contain a mixture of sludge, saltcake and supernatant liquids. The insoluble sludge fraction of the waste consists of metal oxides and hydroxides and contains the bulk of many radionuclides such as the transuranic components and 90Sr. The saltcake, generated by extensive evaporation of aqueous solutions, consists primarily of dried sodium salts. The supernates consist of concentrated (5-15 M) aqueous solutions of sodium and potassium salts. The 177 storage tanks include 149 single-shell tanks (SSTs) and 28 double -hell tanks (DSTs). Ultimately the wastes need to be retrieved from the tanks for treatment and disposal. The SSTs contain minimal amounts of liquid wastes, and the Tank Operations Contractor is continuing a program of moving solid wastes from SSTs to interim storage in the DSTs. The Hanford DST system provides the staging location for waste feed delivery to the Department of Energy (DOE) Office of River Protection’s (ORP) Hanford Tank Waste Treatment and Immobilization Plant (WTP). The WTP is being designed and constructed to pretreat and then vitrify a large portion of the wastes in Hanford’s 177 underground waste storage tanks.

  4. Hazardous Waste: Learn the Basics of Hazardous Waste

    Science.gov (United States)

    ... Agency Search Search Hazardous Waste Contact Us Share Learn the Basics of Hazardous Waste Hazardous waste that ... Regulations part 261 . Select a question below to learn more about each step in the hazardous waste ...

  5. Solid waste management in Asian countries: a review of solid waste minimisation (3'r) towards low carbon

    Science.gov (United States)

    Ali, N. E.; Sion, H. C.

    2014-02-01

    The amount of solid-waste generated in Asian countries has increased tremendously, mainly due to the improvement in living standards, rapid developments in technology, growth in economy and population in the cities. Solid waste management is a global issue and major challenge facing Asian countries and neglecting its management may have negative consequences on the environment. Waste composition data proves the developed countries to have generated more recyclable materials while developing countries produce more organic and less recyclable waste such as paper, plastic and aluminium. In this regard, increase in number of landfills and disposal sites, will have an impact on GHG (greenhouse gas) emissions and pollutants to air and water. Alternative methods should therefore be taken to reduce the volume of waste. Most Asian countries have adopted the 3R (reduce, reuse, recycle) concept in order to reduce solid waste and their governments have implemented laws and regulations in order to support this. Implementation of 3R is the major contributor to the solid waste minimization and it can improve the quality of environmental sustainability and reduction of carbon dioxide emission in to the atmosphere. Based on our review, most of the countries practicing the 3R concept in tandem with laws and regulations perform better than those that just practice the 3R concept without any laws and regulations. The paper suggests that every country must focus on the laws and regulations relating to solid waste minimization so that it could be easily implemented as outlined.

  6. Hanford Site annual dangerous waste report: Volume 1, Part 2, Generator dangerous waste report, dangerous waste

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-12-31

    This report contains information on hazardous materials at the Hanford Site. Information consists of shipment date, physical state, chemical nature, waste description, waste number, weight, and waste designation.

  7. Cyclone Simulation via Action Minimization

    Science.gov (United States)

    Plotkin, D. A.; Weare, J.; Abbot, D. S.

    2016-12-01

    A postulated impact of climate change is an increase in intensity of tropical cyclones (TCs). This hypothesized effect results from the fact that TCs are powered subsaturated boundary layer air picking up water vapor from the surface ocean as it flows inwards towards the eye. This water vapor serves as the energy input for TCs, which can be idealized as heat engines. The inflowing air has a nearly identical temperature as the surface ocean; therefore, warming of the surface leads to a warmer atmospheric boundary layer. By the Clausius-Clapeyron relationship, warmer boundary layer air can hold more water vapor and thus results in more energetic storms. Changes in TC intensity are difficult to predict due to the presence of fine structures (e.g. convective structures and rainbands) with length scales of less than 1 km, while general circulation models (GCMs) generally have horizontal resolutions of tens of kilometers. The models are therefore unable to capture these features, which are critical to accurately simulating cyclone structure and intensity. Further, strong TCs are rare events, meaning that long multi-decadal simulations are necessary to generate meaningful statistics about intense TC activity. This adds to the computational expense, making it yet more difficult to generate accurate statistics about long-term changes in TC intensity due to global warming via direct simulation. We take an alternative approach, applying action minimization techniques developed in molecular dynamics to the WRF weather/climate model. We construct artificial model trajectories that lead from quiescent (TC-free) states to TC states, then minimize the deviation of these trajectories from true model dynamics. We can thus create Monte Carlo model ensembles that are biased towards cyclogenesis, which reduces computational expense by limiting time spent in non-TC states. This allows for: 1) selective interrogation of model states with TCs; 2) finding the likeliest paths for

  8. Using MCDA and GIS for hazardous waste landfill siting considering land scarcity for waste disposal

    Energy Technology Data Exchange (ETDEWEB)

    Feo, Giovanni De, E-mail: g.defeo@unisa.it [Department of Industrial Engineering, University of Salerno, via Giovanni Paolo II, 132, 84084 Fisciano, SA (Italy); Gisi, Sabino De [Italian National Agency for New Technologies, Energy and Sustainable Economic Development, ENEA, Water Resource Management Lab., via Martiri di Monte Sole 4, 40129 Bologna, BO (Italy)

    2014-11-15

    Highlights: • Wasting land for the siting of hazardous waste landfills must be avoided. • The siting procedure is based on a land use map of potentially suitable areas. • All the waste facilities of the management system are simultaneously considered. • A case study is developed considering two multi-criteria techniques. • An innovative criteria weighting tool (PSW) is used in combination with the AHP. - Abstract: The main aim of this study was to develop a procedure that minimizes the wasting of space for the siting of hazardous waste landfills as part of a solid waste management system. We wanted to tackle the shortage of land for waste disposal that is a serious and growing problem in most large urban regions. The procedure combines a multi-criteria decision analysis (MCDA) approach with a geographical information system (GIS). The GIS was utilised to obtain an initial screening in order to eliminate unsuitable areas, whereas the MCDA was developed to select the most suitable sites. The novelty of the proposed siting procedure is the introduction of a new screening phase before the macro-siting step aimed at producing a “land use map of potentially suitable areas” for the siting of solid waste facilities which simultaneously takes into consideration all plant types. The issue of obtaining sites evaluations of a specific facility was coupled with the issue of not wasting land appropriate to facilitate other types of waste management options. In the developed case study, the use of an innovative criteria weighting tool (the “Priority Scale”) in combination with the Analytic Hierarchy Process was useful to easier define the priorities of the evaluation criteria in comparison with other classic methods such as the Paired Comparison Technique in combination with the Simple Additive Weighting method.

  9. Mini-Med School Planning Guide

    Science.gov (United States)

    National Institutes of Health, Office of Science Education, 2008

    2008-01-01

    Mini-Med Schools are public education programs now offered by more than 70 medical schools, universities, research institutions, and hospitals across the nation. There are even Mini-Med Schools in Ireland, Malta, and Canada! The program is typically a lecture series that meets once a week and provides "mini-med students" information on some of the…

  10. Anaerobic digestion of municipal solid waste and agricultural waste and the effect of co-digestion with dairy cow manure.

    Science.gov (United States)

    Macias-Corral, Maritza; Samani, Zohrab; Hanson, Adrian; Smith, Geoffrey; Funk, Paul; Yu, Hui; Longworth, John

    2008-11-01

    Anaerobic digestion of dairy cow manure (CM), the organic fraction of municipal solid waste (OFMSW), and cotton gin waste (CGW) was investigated with a two-phase pilot-scale anaerobic digestion (AD) system. The OFMSW and CM were digested as single wastes and as combined wastes. The single waste digestion of CM resulted in 62m3 methane/ton of CM on dry weight basis. The single waste digestion of OFMSW produced 37m3 methane/ton of dry waste. Co-digestion of OFMSW and CM resulted in 172m3 methane/ton of dry waste. Co-digestion of CGW and CM produced 87m3 methane/ton of dry waste. Comparing the single waste digestions with co-digestion of combined wastes, it was shown that co-digestion resulted in higher methane gas yields. In addition, co-digestion of OFMSW and CM promotes synergistic effects resulting in higher mass conversion and lower weight and volume of digested residual.

  11. Operational tank leak detection and minimization during retrieval

    Energy Technology Data Exchange (ETDEWEB)

    Hertzel, J.S.

    1996-03-01

    This report evaluates the activities associated with the retrieval of wastes from the single-shell tanks proposed under the initial Single-Shell Tank Retrieval System. This report focuses on minimizing leakage during retrieval by using effective leak detection and mitigating actions. After reviewing the historical data available on single-shell leakage, and evaluating current leak detection technology, this report concludes that the only currently available leak detection method which can function within the most probable leakage range is the mass balance system. If utilized after each sluicing campaign, this method should allow detection at a leakage value well below the leakage value where significant health effects occur which is calculated for each tank. Furthermore, this report concludes that the planned sequence or sluicing activities will serve to further minimize the probability and volume of leaks by keeping liquid away from areas with the greatest potential for leaking. Finally, this report identifies a series of operational responses which when used in conjunction with the recommended sluicing sequence and leak detection methods will minimize worker exposure and environmental safety health risks.

  12. RE-UTILIZATION OF INORGANIC SOLID WASTE (LIME MUD) AS FOREST ROAD STABILIZER FROM THE CHEMICAL RECOVERY PROCESS IN KRAFT PULP MILL

    OpenAIRE

    Habip Eroğlu; Sami İmamoğlu; H. Hulusi Acar

    2005-01-01

    Waste handling is a concern in all pulp and paper mills. Best available techniques for reducing waste is to minimize the generation of solid waste and/or reuse these materials, wherever practicable. One of the most important solid wastes is lime mud which is generated from the kraft pulping in its chemical recovery process. This paper explores the composition of lime mud resulting from the chemical recovery unite of kraft pulp mill and investigation of this waste for re-using beneficial...

  13. Against explanatory minimalism in psychiatry

    Directory of Open Access Journals (Sweden)

    Tim eThornton

    2015-12-01

    Full Text Available The idea that psychiatry contains, in principle, a series of levels of explanation has been criticised both as empirically false but also, by Campbell, as unintelligible because it presupposes a discredited pre-Humean view of causation. Campbell’s criticism is based on an interventionist-inspired denial that mechanisms and rational connections underpin physical and mental causation respectively and hence underpin levels of explanation. These claims echo some superficially similar remarks in Wittgenstein’s Zettel. But attention to the context of Wittgenstein’s remarks suggests a reason to reject explanatory minimalism in psychiatry and reinstate a Wittgensteinian notion of level of explanation. Only in a context broader than the one provided by interventionism is the ascription of propositional attitudes, even in the puzzling case of delusions, justified. Such a view, informed by Wittgenstein, can reconcile the idea that the ascription mental phenomena presupposes a particular level of explanation with the rejection of an a priori claim about its connection to a neurological level of explanation.

  14. Against Explanatory Minimalism in Psychiatry.

    Science.gov (United States)

    Thornton, Tim

    2015-01-01

    The idea that psychiatry contains, in principle, a series of levels of explanation has been criticized not only as empirically false but also, by Campbell, as unintelligible because it presupposes a discredited pre-Humean view of causation. Campbell's criticism is based on an interventionist-inspired denial that mechanisms and rational connections underpin physical and mental causation, respectively, and hence underpin levels of explanation. These claims echo some superficially similar remarks in Wittgenstein's Zettel. But attention to the context of Wittgenstein's remarks suggests a reason to reject explanatory minimalism in psychiatry and reinstate a Wittgensteinian notion of levels of explanation. Only in a context broader than the one provided by interventionism is that the ascription of propositional attitudes, even in the puzzling case of delusions, justified. Such a view, informed by Wittgenstein, can reconcile the idea that the ascription mental phenomena presupposes a particular level of explanation with the rejection of an a priori claim about its connection to a neurological level of explanation.

  15. Minimalism through intraoperative functional mapping.

    Science.gov (United States)

    Berger, M S

    1996-01-01

    Intraoperative stimulation mapping may be used to avoid unnecessary risk to functional regions subserving language and sensori-motor pathways. Based on the data presented here, language localization is variable in the entire population, with only certainty existing for the inferior frontal region responsible for motor speech. Anatomical landmarks such as the anterior temporal tip for temporal lobe language sites and the posterior aspect of the lateral sphenoid wing for the frontal lobe language zones are unreliable in avoiding postoperative aphasias. Thus, individual mapping to identify essential language sites has the greatest likelihood of avoiding permanent deficits in naming, reading, and motor speech. In a similar approach, motor and sensory pathways from the cortex and underlying white matter may be reliably stimulated and mapped in both awake and asleep patients. Although these techniques require an additional operative time and equipment nominally priced, the result is often gratifying, as postoperative morbidity has been greatly reduced in the process of incorporating these surgical strategies. The patients quality of life is improved in terms of seizure control, with or without antiepileptic drugs. This avoids having to perform a second costly operative procedure, which is routinely done when extraoperative stimulation and recording is done via subdural grids. In addition, an aggressive tumor resection at the initial operation lengthens the time to tumor recurrence and often obviates the need for a subsequent reoperation. Thus, intraoperative functional mapping may be best alluded to as a surgical technique that results in "minimalism in the long term".

  16. Robotic assisted minimally invasive surgery

    Directory of Open Access Journals (Sweden)

    Palep Jaydeep

    2009-01-01

    Full Text Available The term "robot" was coined by the Czech playright Karel Capek in 1921 in his play Rossom′s Universal Robots. The word "robot" is from the check word robota which means forced labor.The era of robots in surgery commenced in 1994 when the first AESOP (voice controlled camera holder prototype robot was used clinically in 1993 and then marketed as the first surgical robot ever in 1994 by the US FDA. Since then many robot prototypes like the Endoassist (Armstrong Healthcare Ltd., High Wycombe, Buck, UK, FIPS endoarm (Karlsruhe Research Center, Karlsruhe, Germany have been developed to add to the functions of the robot and try and increase its utility. Integrated Surgical Systems (now Intuitive Surgery, Inc. redesigned the SRI Green Telepresence Surgery system and created the daVinci Surgical System ® classified as a master-slave surgical system. It uses true 3-D visualization and EndoWrist ® . It was approved by FDA in July 2000 for general laparoscopic surgery, in November 2002 for mitral valve repair surgery. The da Vinci robot is currently being used in various fields such as urology, general surgery, gynecology, cardio-thoracic, pediatric and ENT surgery. It provides several advantages to conventional laparoscopy such as 3D vision, motion scaling, intuitive movements, visual immersion and tremor filtration. The advent of robotics has increased the use of minimally invasive surgery among laparoscopically naοve surgeons and expanded the repertoire of experienced surgeons to include more advanced and complex reconstructions.

  17. Radappertization of minimally processed carrots

    Energy Technology Data Exchange (ETDEWEB)

    Walder, Juliana F.A.; Walder, Julio M.M. [Centro de Energia Nuclear na Agricultura (CENA/USP), Piracicaba, SP (Brazil)]. E-mails: juwalder@gmail.com; jmwalder@cena.usp.br; Souza, Miriam C. de [Universidade Metodista de Piracicaba (UNIMEP), SP (Brazil)]. E-mail: mcsouza@unimep.br; Spoto, Marta H.F. [Universidade de Sao Paulo (USP), Piracicaba, SP (Brazil). Escola Superior de Agricultura Luiz de Queiroz (ESALQ)]. E-mail: mhfspoto@esalq.usp.br

    2007-07-01

    Full text: The goal of this work was to obtain shelf-stable irradiated carrots. It was evaluate the effect of high-doses (radappertization) of gamma radiation (Cobalt-60) on minimally processed carrots cv. Nantes. Before irradiation carrots were blanched, vacuum packaged in polyethylene film (52 {mu}m) and frozen (-80 deg C) prior to and during radiation processing. Used doses were 10, 20 and 30 kGy. After irradiation the carrot bags were kept at room conditions (25 - 28 deg C and RH 60-80 %) for 90 days period. Physical-chemical characteristics and microorganism population were determined at 1, 30 60 and 90 days after radiation process. Radappertization decreased total soluble solids (TSS), hardness and color. Radiation was responsible for reduction of 15,5% of total carotenoids content. By the other hand the storage period was responsible for 35 % losses. pH was not affected by radiation nor by storage period. Complete sterilization was achieved with doses of 20 kGy and 30 kGy. Radappertization affected negatively the sensorial characteristics of flavor, color and general appearance. Through sensorial analysis was possible to evaluate that polyethylene seal was inadequate for the purpose because allowed photo-chemical reactions in the carrots during the storage period. The metallized film kept best appearance of the irradiated carrots after 90 days storage. (author)

  18. Renormalization of minimally doubled fermions

    Science.gov (United States)

    Capitani, Stefano; Creutz, Michael; Weber, Johannes; Wittig, Hartmut

    2010-09-01

    We investigate the renormalization properties of minimally doubled fermions, at one loop in perturbation theory. Our study is based on the two particular realizations of Boriçi-Creutz and Karsten-Wilczek. A common feature of both formulations is the breaking of hyper-cubic symmetry, which requires that the lattice actions are supplemented by suitable counterterms. We show that three counterterms are required in each case and determine their coefficients to one loop in perturbation theory. For both actions we compute the vacuum polarization of the gluon. It is shown that no power divergences appear and that all contributions which arise from the breaking of Lorentz symmetry are cancelled by the counterterms. We also derive the conserved vector and axial-vector currents for Karsten-Wilczek fermions. Like in the case of the previously studied Boriçi-Creutz action, one obtains simple expressions, involving only nearest-neighbour sites. We suggest methods how to fix the coefficients of the counterterms non-perturbatively and discuss the implications of our findings for practical simulations.

  19. Pinellas Plant contingency plan for the hazardous waste management facility

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1988-04-01

    Subpart D of Part 264 (264.50 through .56) of the Resource Conservation and Recovery Act (RCRA) regulations require that each facility maintain a contingency plan detailing procedures to {open_quotes}minimize hazards to human health or the environment from fires, explosions, or any unplanned sudden or non-sudden release of hazardous waste or hazardous waste constituents to air, soil, or surface water.{close_quotes}

  20. A Price Discrimination Model of Trade Promotions

    OpenAIRE

    Tony Haitao Cui; Jagmohan S. Raju; Z. John Zhang

    2008-01-01

    Critics have long faulted the wide-spread practice of trade promotions as wasteful. It has been estimated that this practice adds up to $100 billion worth of inventory to the distribution system. Yet, the practice continues. In this paper, we propose a price discrimination model of trade promotions. We show that in a distribution channel characterized by a dominant retailer, a manufacturer has incentives to price discriminate between the dominant retailer and smaller independents. While offer...

  1. Processing of waste solutions from electrochemical decontamination

    Energy Technology Data Exchange (ETDEWEB)

    Charlot, L.A.; Allen, R.P.; Arrowsmith, H.W.; Hooper, J.L.

    1979-09-01

    The use of electropolishing as a decontamination technique will be effective only if we can minimize the amount of secondary waste requiring disposal and economically recycle part of the decontamination electrolyte. Consequently, a solution purification method is needed to remove the dissolved contamination and metal in the electrolyte. This report describes the selection of a purification method for a phosphoric acid electrolyte from the following possible acid reclamation processes: ion exchange, solvent extraction, precipitation, distillation, electrolysis, and membrane separation.

  2. Low-level radioactive biomedical wastes

    Energy Technology Data Exchange (ETDEWEB)

    Casarett, G.W.

    A summary of the management and hazards of low-level radioactive biomedical wastes is presented. The volume, disposal methods, current problems, regulatory agencies, and possible solutions to disposal problems are discussed. The benefits derived from using radioactivity in medicine are briefly described. Potential health risks are discussed. The radioactivity in most of the radioactive biomedical waste is a small fraction of that contained naturally in the human body or in the natural environment. Benefit-risk-cost considerations are presented. The cost of managing these wastes is getting so high that a new perspective for comparison of radioactivity (facts, risks, costs, benefits and trade-offs) and alternate approaches to minimize the risk and cost and maximize the benefits is suggested. (DMC)

  3. Integrated solid waste management of Minneapolis, Minnesota

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-11-01

    The subject document reports the results of an in-depth investigation of the fiscal year 1992 cost of the City of Minneapolis, Minnesota (Hennepin County) integrated municipal solid waste management (IMSWM) system, the energy consumed to operate the system, and the environmental performance requirements for each of the system`s waste-processing and disposal facilities. Actual data from records kept by participants is reported in this document. Every effort was made to minimize the use of assumptions, and no attempt is made to interpret the data reported. Analytical approaches are documented so that interested analysts may perform manipulation or further analysis of the data. As such, the report is a reference document for municipal solid waste (MSW) management professionals who are interested in the actual costs and energy consumption for a one-year period, of an operating IMSWM system.

  4. Minimally invasive surgery for the lumbar spine.

    Science.gov (United States)

    Gandhi, S D; Anderson, D G

    2012-03-01

    Minimally invasive spine surgery is a rapidly developing field that has the potential to decrease surgical morbidity and improve recovery compared to traditional spinal approaches. Minimally invasive approaches have been developed for all regions of the spine, but have been best documented for degenerative conditions of the lumbar spine. Lumbar decompression and lumbar interbody fusion are two of the most well-studied minimally invasive surgical approaches. This article will review both the rationale and technique for minimally invasive lumbar decompression and for a minimally invasive transforaminal lumbar interbody fusion (TLIF).

  5. Minimally invasive surgery in pelvic floor repair.

    Science.gov (United States)

    Zwain, Omar; Aoun, Joelle; Eisenstein, David

    2017-08-01

    To review the use and efficacy of minimally invasive surgery in pelvic organ prolapse (POP) repair. This review summarizes surgical options for management of POP with special emphasis on minimally invasive surgical approach and discusses the recent experience and feasibility of integrating robot-assisted technology. Minimally invasive approaches have equal efficacy and less morbidity than laparotomy for POP repair, particularly apical prolapse. Robotics may facilitate the rate of minimally invasive surgery for POP repair with greater cost and as yet no proven superiority for conventional laparoscopy. Minimally invasive surgery is the preferred approach to POP repair. Conventional laparoscopic or robotic sacral colpopexy is recommended for apical defect and procidentia.

  6. Construction and Demolition Waste

    DEFF Research Database (Denmark)

    Christensen, Thomas Højlund; Andersen, L.

    2011-01-01

    Construction and demolition waste (C&D waste) is the waste generated during the building, repair, remodeling or removal of constructions. The constructions can be roads, residential housing and nonresidential buildings. C&D waste has traditionally been considered without any environmental problems...... and has just been landfilled. However, in recent years more focus has been put on C&D waste and data are starting to appear. One reason is that it has been recognized that C&D waste may include many materials that are contaminated either as part of their original design or through their use and therefore...... should be managed accordingly. Another reason is that it has been documented that a large fraction of C&D waste (about 90 %) can be easily recycled and thus can conserve landfill capacity. C&D waste may conveniently be divided into three subcategories: Buildings, roads and excavations. This chapter...

  7. Waste canister for storage of nuclear wastes

    Science.gov (United States)

    Duffy, James B.

    1977-01-01

    A waste canister for storage of nuclear wastes in the form of a solidified glass includes fins supported from the center with the tips of the fins spaced away from the wall to conduct heat away from the center without producing unacceptable hot spots in the canister wall.

  8. Business unusual - Waste Act implementation: solid waste

    CSIR Research Space (South Africa)

    Oelofse, Suzanna HH

    2013-08-01

    Full Text Available The preamble to the Waste Act (2008) is very clear that, as a result of this legislation, waste management in South Africa will never be the same again. This should send a clear message that ‘business as usual’ will no longer be sufficient....

  9. Generation and management of waste electric vehicle batteries in China.

    Science.gov (United States)

    Xu, ChengJian; Zhang, Wenxuan; He, Wenzhi; Li, Guangming; Huang, Juwen; Zhu, Haochen

    2017-09-01

    With the increasing adoption of EVs (electric vehicles), a large number of waste EV LIBs (electric vehicle lithium-ion batteries) were generated in China. Statistics showed generation of waste EV LIBs in 2016 reached approximately 10,000 tons, and the amount of them would be growing rapidly in the future. In view of the deleterious effects of waste EV LIBs on the environment and the valuable energy storage capacity or materials that can be reused in them, China has started emphasizing the management, reuse, and recycling of them. This paper presented the generation trend of waste EV LIBs and focused on interrelated management development and experience in China. Based on the situation of waste EV LIBs management in China, existing problems were analyzed and summarized. Some recommendations were made for decision-making organs to use as valuable references to improve the management of waste EV LIBs and promote the sustainable development of EVs.

  10. Health promotion is peace promotion.

    Science.gov (United States)

    Middleton, J D

    1987-01-01

    This paper discusses the effects of the arms race on health, in the absence of nuclear war. High levels of military expenditure are inextricably linked to unemployment, poverty, starvation and ill health. Alternatives to the escalation of military expenditure are possible; health promotion can be involved in wider public health initiatives towards economic and industrial conversion to peaceful, socially useful production. The interests of the health and scientific communities have traditionally transcended narrow chauvinism and nationalism. World Health Organization activities such as work towards primary health care and the Expanded Programme on Immunization actively involve international co-operation, demystify potential enemies and promote health and peace.

  11. Promoter analysis by saturation mutagenesis

    Directory of Open Access Journals (Sweden)

    Baliga Nitin

    2001-01-01

    Full Text Available Gene expression and regulation are mediated by DNA sequences, in most instances, directly upstream to the coding sequences by recruiting transcription factors, regulators, and a RNA polymerase in a spatially defined fashion. Few nucleotides within a promoter make contact with the bound proteins. The minimal set of nucleotides that can recruit a protein factor is called a cis-acting element. This article addresses a powerful mutagenesis strategy that can be employed to define cis-acting elements at a molecular level. Technical details including primer design, saturation mutagenesis, construction of promoter libraries, phenotypic analysis, data analysis, and interpretation are discussed.

  12. Biohazardous waste management plan.

    Energy Technology Data Exchange (ETDEWEB)

    Lane, Todd W.

    2004-01-01

    This plan describes the process for managing non-medical biohazardous waste at Sandia National Laboratories California. It applies to operations at the Chemical and Radiation Detection Laboratory (CRDL), Building 968, and other biosafety level 1 or 2 activities at the site. It addresses the accumulation, storage, treatment and disposal of biohazardous waste and sharps waste. It also describes the procedures to comply with regulatory requirements and SNL policies applicable to non-medical biohazardous waste.

  13. Medical waste management plan.

    Energy Technology Data Exchange (ETDEWEB)

    Lane, Todd W.; VanderNoot, Victoria A.

    2004-12-01

    This plan describes the process for managing research generated medical waste at Sandia National Laboratories/California. It applies to operations at the Chemical and Radiation Detection Laboratory (CRDL), Building 968, and other biosafety level 1 or 2 activities at the site. It addresses the accumulation, storage, treatment and disposal of medical waste and sharps waste. It also describes the procedures to comply with regulatory requirements and SNL policies applicable to medical waste.

  14. INTEGRATED WASTE MANAGEMENT SYSTEM

    OpenAIRE

    Truptimala Patanaik; Ambika Priyadarshini Mishra; Aishariya Durga; Gayatri Avipsa

    2016-01-01

    The towns and cities have become the centres of population growth and require three essential services viz., water supply, waste water treatment and solid wastes disposal. The tremendous increase in population accelerates the amount of municipal solid waste (MSW) generation. Hence, the solid waste management (SWM) is one of the essential municipal services, to protect the environment, safeguard public health services and improve productivity.   In this context the case study is c...

  15. Solid waste handling

    Energy Technology Data Exchange (ETDEWEB)

    Parazin, R.J.

    1995-05-31

    This study presents estimates of the solid radioactive waste quantities that will be generated in the Separations, Low-Level Waste Vitrification and High-Level Waste Vitrification facilities, collectively called the Tank Waste Remediation System Treatment Complex, over the life of these facilities. This study then considers previous estimates from other 200 Area generators and compares alternative methods of handling (segregation, packaging, assaying, shipping, etc.).

  16. Minimal complexity control law synthesis

    Science.gov (United States)

    Bernstein, Dennis S.; Haddad, Wassim M.; Nett, Carl N.

    1989-01-01

    A paradigm for control law design for modern engineering systems is proposed: Minimize control law complexity subject to the achievement of a specified accuracy in the face of a specified level of uncertainty. Correspondingly, the overall goal is to make progress towards the development of a control law design methodology which supports this paradigm. Researchers achieve this goal by developing a general theory of optimal constrained-structure dynamic output feedback compensation, where here constrained-structure means that the dynamic-structure (e.g., dynamic order, pole locations, zero locations, etc.) of the output feedback compensation is constrained in some way. By applying this theory in an innovative fashion, where here the indicated iteration occurs over the choice of the compensator dynamic-structure, the paradigm stated above can, in principle, be realized. The optimal constrained-structure dynamic output feedback problem is formulated in general terms. An elegant method for reducing optimal constrained-structure dynamic output feedback problems to optimal static output feedback problems is then developed. This reduction procedure makes use of star products, linear fractional transformations, and linear fractional decompositions, and yields as a byproduct a complete characterization of the class of optimal constrained-structure dynamic output feedback problems which can be reduced to optimal static output feedback problems. Issues such as operational/physical constraints, operating-point variations, and processor throughput/memory limitations are considered, and it is shown how anti-windup/bumpless transfer, gain-scheduling, and digital processor implementation can be facilitated by constraining the controller dynamic-structure in an appropriate fashion.

  17. Minimal models of multidimensional computations.

    Directory of Open Access Journals (Sweden)

    Jeffrey D Fitzgerald

    2011-03-01

    Full Text Available The multidimensional computations performed by many biological systems are often characterized with limited information about the correlations between inputs and outputs. Given this limitation, our approach is to construct the maximum noise entropy response function of the system, leading to a closed-form and minimally biased model consistent with a given set of constraints on the input/output moments; the result is equivalent to conditional random field models from machine learning. For systems with binary outputs, such as neurons encoding sensory stimuli, the maximum noise entropy models are logistic functions whose arguments depend on the constraints. A constraint on the average output turns the binary maximum noise entropy models into minimum mutual information models, allowing for the calculation of the information content of the constraints and an information theoretic characterization of the system's computations. We use this approach to analyze the nonlinear input/output functions in macaque retina and thalamus; although these systems have been previously shown to be responsive to two input dimensions, the functional form of the response function in this reduced space had not been unambiguously identified. A second order model based on the logistic function is found to be both necessary and sufficient to accurately describe the neural responses to naturalistic stimuli, accounting for an average of 93% of the mutual information with a small number of parameters. Thus, despite the fact that the stimulus is highly non-Gaussian, the vast majority of the information in the neural responses is related to first and second order correlations. Our results suggest a principled and unbiased way to model multidimensional computations and determine the statistics of the inputs that are being encoded in the outputs.

  18. Robotic assisted minimally invasive surgery

    Science.gov (United States)

    Palep, Jaydeep H

    2009-01-01

    The term “robot” was coined by the Czech playright Karel Capek in 1921 in his play Rossom's Universal Robots. The word “robot” is from the check word robota which means forced labor. The era of robots in surgery commenced in 1994 when the first AESOP (voice controlled camera holder) prototype robot was used clinically in 1993 and then marketed as the first surgical robot ever in 1994 by the US FDA. Since then many robot prototypes like the Endoassist (Armstrong Healthcare Ltd., High Wycombe, Buck, UK), FIPS endoarm (Karlsruhe Research Center, Karlsruhe, Germany) have been developed to add to the functions of the robot and try and increase its utility. Integrated Surgical Systems (now Intuitive Surgery, Inc.) redesigned the SRI Green Telepresence Surgery system and created the daVinci Surgical System® classified as a master-slave surgical system. It uses true 3-D visualization and EndoWrist®. It was approved by FDA in July 2000 for general laparoscopic surgery, in November 2002 for mitral valve repair surgery. The da Vinci robot is currently being used in various fields such as urology, general surgery, gynecology, cardio-thoracic, pediatric and ENT surgery. It provides several advantages to conventional laparoscopy such as 3D vision, motion scaling, intuitive movements, visual immersion and tremor filtration. The advent of robotics has increased the use of minimally invasive surgery among laparoscopically naïve surgeons and expanded the repertoire of experienced surgeons to include more advanced and complex reconstructions. PMID:19547687

  19. Utilization of household food waste for the production of ethanol at high dry material content

    National Research Council Canada - National Science Library

    Matsakas, Leonidas; Kekos, Dimitris; Loizidou, Maria; Christakopoulos, Paul

    2014-01-01

    .... In order to minimize the competition between fuels and food production, researchers are focusing their efforts to the utilization of wastes and by-products as raw materials for the production of ethanol...

  20. Upper Mississippi River National Wildlife & Fish Refuge FY15 Chronic Wasting Disease Report

    Data.gov (United States)

    Department of the Interior — The Refuge completed a Chronic Wasting Disease Surveillance and Management Plan (CWD Plan) in 2005. The goals of the Refuge’s CWD Plan are to: 1) minimize the impact...

  1. Upper Mississippi River National Wildlife and Fish Refuge Chronic Wasting Disease Monitoring

    Data.gov (United States)

    Department of the Interior — The Refuge completed a Chronic Wasting Disease Surveillance and Management Plan (CWD Plan) in 2005. The goals of the Refuge’s CWD Plan are to: 1) minimize the impact...

  2. 36 CFR 6.4 - Solid waste disposal sites not in operation on September 1, 1984.

    Science.gov (United States)

    2010-07-01

    ... treatment plant, septic system waste, or domestic sewage; (vii) Petroleum, including used crankcase oil from... pests and vermin, and to minimize noise, odor, feeding by native wildlife and conflicts with visitor...

  3. Getting a taste for food waste: a mixed methods ethnographic study into hospital food waste before patient consumption conducted at three New Zealand foodservice facilities.

    Science.gov (United States)

    Goonan, Sarah; Mirosa, Miranda; Spence, Heather

    2014-01-01

    Foodservice organizations, particularly those in hospitals, are large producers of food waste. To date, research on waste in hospitals has focused primarily on plate waste and the affect of food waste on patient nutrition outcomes. Less focus has been placed on waste generation at the kitchen end of the hospital food system. We used a novel approach to understand reasons for hospital food waste before consumption and offer recommendations on waste minimization within foodservices. A mixed methods ethnographic research approach was adopted. Three New Zealand hospital foodservices were selected as research sites, all of which were contracted to an external foodservice provider. Data collection techniques included document analyses, observations, focus groups with kitchen staff, and one-on-one interviews with managers. Thematic analysis was conducted to generate common themes. Most food waste occurred during service and as a result of overproduction. Attitudes and habits of foodservice personnel were considered influential factors of waste generation. Implications of food waste were perceived differently by different levels of staff. Whereas managers raised discussion from a financial perspective, kitchen staff drew upon social implications. Organizational plans, controls, and use of pre-prepared ingredients assisted in waste minimization. An array of factors influenced waste generation in hospital foodservices. Exploring attitudes and practices of foodservice personnel allowed an understanding of reasons behind hospital food waste and ways in which it could be minimized. This study provides a foundation for further research on sustainable behavior within the wider foodservice sector and dietetics practice. Copyright © 2014 Academy of Nutrition and Dietetics. Published by Elsevier Inc. All rights reserved.

  4. Household food waste

    NARCIS (Netherlands)

    Wahlen, S.; Winkel, Thomas

    2017-01-01

    Food waste is debated not only in the light of sustainable consumption in research and policy, but also in the broader public. This article focuses on food waste in household contexts, what is widely believed the end of the food chain. However, household food waste is far more complex and intricate

  5. Nuclear wastes; Dechets nucleaires

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2004-07-01

    Here is made a general survey of the situation relative to radioactive wastes. The different kinds of radioactive wastes and the different way to store them are detailed. A comparative evaluation of the situation in France and in the world is made. The case of transport of radioactive wastes is tackled. (N.C.)

  6. Waste disposal package

    Science.gov (United States)

    Smith, M.J.

    1985-06-19

    This is a claim for a waste disposal package including an inner or primary canister for containing hazardous and/or radioactive wastes. The primary canister is encapsulated by an outer or secondary barrier formed of a porous ceramic material to control ingress of water to the canister and the release rate of wastes upon breach on the canister. 4 figs.

  7. Radioactive Wastes. Revised.

    Science.gov (United States)

    Fox, Charles H.

    This publication is one of a series of information booklets for the general public published by the United States Atomic Energy Commission. This booklet deals with the handling, processing and disposal of radioactive wastes. Among the topics discussed are: The Nature of Radioactive Wastes; Waste Management; and Research and Development. There are…

  8. Rock & Roll : Waste seperation

    NARCIS (Netherlands)

    Beunder, L.; Rem, P.C.; Van Den Berg, R.

    2000-01-01

    Five hundred tonnes of glass, 1 million tonnes of plastic,14 million tonnes of building and demolition waste, 7 million tonnes of household waste, 3 million tonnes of packaging, 3.5 million tonnes of paper and board, and 300,000 old cars. All part of the annual harvest of waste materials in the

  9. Waste vs Resource Management

    CSIR Research Space (South Africa)

    Oelofse, Suzanna HH

    2014-10-01

    Full Text Available Recent global waste statistics show that in the order of 70% of all municipal waste generated worldwide is disposed at landfill, 11% is treated in thermal and Waste-to-Energy (WtE) facilities and the rest (19%) is recycled or treated by mechanical...

  10. Warpage minimization on wheel caster by optimizing process parameters using response surface methodology (RSM)

    Science.gov (United States)

    Safuan, N. S.; Fathullah, M.; Shayfull, Z.; Nasir, S. M.; Hazwan, M. H. M.

    2017-09-01

    In injection moulding process, it is important to keep the productivity increase constantly with least of waste produced such as warpage defect. Thus, this study is concerning on minimizing warpage defect on wheel caster part. Apart from eliminating product wastes, this project also giving out best optimization techniques using response surface methodology. This research studied on five parameters A-packing pressure, B-packing time, C-mold temperature, D-melting temperature and E-cooling time. The optimization showed that packing pressure is the most significant parameter. Warpage have been improved 42.64% from 0.6524 mm to 0.3742mm.

  11. System dynamic modeling on construction waste management in Shenzhen, China.

    Science.gov (United States)

    Tam, Vivian W Y; Li, Jingru; Cai, Hong

    2014-05-01

    This article examines the complexity of construction waste management in Shenzhen, Mainland China. In-depth analysis of waste generation, transportation, recycling, landfill and illegal dumping of various inherent management phases is explored. A system dynamics modeling using Stella model is developed. Effects of landfill charges and also penalties from illegal dumping are also simulated. The results show that the implementation of comprehensive policy on both landfill charges and illegal dumping can effectively control the illegal dumping behavior, and achieve comprehensive construction waste minimization. This article provides important recommendations for effective policy implementation and explores new perspectives for Shenzhen policy makers.

  12. High-temperature vacuum distillation separation of plutonium waste salts

    Energy Technology Data Exchange (ETDEWEB)

    Garcia, E. [Los Alamos National Lab., NM (United States)

    1996-10-01

    In this task, high-temperature vacuum distillation separation is being developed for residue sodium chloride-potassium chloride salts resulting from past pyrochemical processing of plutonium. This process has the potential of providing clean separation of the salt and the actinides with minimal amounts of secondary waste generation. The process could produce chloride salt that could be discarded as low-level waste (LLW) or low actinide content transuranic (TRU) waste, and a concentrated actinide oxide powder that would meet long-term storage standards (DOE-DTD-3013-94) until a final disposition option for all surplus plutonium is chosen.

  13. Use of Saccharomyces cerevisiae in radioactive waste treatment

    Energy Technology Data Exchange (ETDEWEB)

    Ferreira, Rafael Vicente de P.; Marumo, Julio T.; Bellini, Maria H.; Potiens Junior, Ademar J.; Takara, Aline S.; Goes, Marcos M. de; Borba, Tania R. de; Nascimento, Carina M. do; Sakata, Solange K. [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil)]. E-mail: rpadua@ipen.br

    2007-07-01

    Waste management plays an important role in reducing the volume of radioactive waste streams, minimizing the cost of the final disposal and the impact on the environment. In this context, new research should focus on the development of simpler and cheaper techniques which may improve the waste processing. The use of biomass in processes concerned with the removal of heavy metals and radionuclides offers significant potential in the treatment of waste-liquid streams. Saccharomyces cerevisiae is well known for its capacity of heavy metals biosorption and it also has the additional advantages such as easy availability and the possibility of genetic manipulation. The aim of this work is to study the potential of the free cell and immobilized S. cerevisiae in bentonite in the removal Americium-241 from radioactive liquid streams produced by Radioactive Waste Laboratory of Nuclear and Energy Research Institute (IPEN-CNEN/SP). (author)

  14. Sustainable Stream Waste Load Allocation with Considering Equity

    Science.gov (United States)

    Liao, W.; Tung, C.

    2007-12-01

    The stream assimilative capacity is the carrying capacity of a river for the maximum waste load without exceeding the water quality standard. However, only optimizing maximal waste loads may lead to inequity. Equity is an important issue in waste load allocation problems. This research formulates a multi-objective model that considers minimizing inequity and maximizing total waste loads by using water quality models, as well as combining Gini coefficient and Data Envelopment Analysis (DEA) to assess the relationship between the equity levels and the maximum waste load. It is also discussed that the impacts of changes in the land use among up- stream and down-stream on assimilative capacity and equity, which can provide useful information for the policy making of sustainable watershed management.

  15. International co-operation in the management of radioactive wastes

    Energy Technology Data Exchange (ETDEWEB)

    Kang, Changsun [Seoul National University (Korea, Republic of)

    1998-07-01

    The use of nuclear energy faces with the problem of radioactive waste disposal. The public simply abhors radioactive wastes without rightful cause. Hence, the immediate concern is to overcome this hostile preconception of the public, and to come up with safe and economic ways of disposal which are acceptable to the public. Without it, the public may not accept the idea of further use of nuclear energy. Some have concern about safeguards of fissile plutonium with respect to proliferation while others have concerns regarding protection beyond national borders related to movement of radioactive wastes for foreign disposal. Now, the disposal of radioactive waste is a global problem rather than a problem for individual nation. In this aspect, close international cooperation is recently being brought up more than ever in jointly: improving public acceptance, minimizing waste generation, eliminating the burden on future generations, developing internationally acceptable practices, exploring disposal concepts, and collaborating on R and D. (author)

  16. Viscosity-based high temperature waste form compositions

    Energy Technology Data Exchange (ETDEWEB)

    Reimann, G.A.

    1994-12-31

    High-temperature waste forms such as iron-enriched basalt are proposed to immobilize and stabilize a variety of low-level wastes stored at the Idaho National Engineering Laboratory. The combination of waste and soil anticipated for the waste form results in high SiO{sub 2} + Al{sub 2}O{sub 3} producing a viscous melt in an arc furnace. Adding a flux such as CaO to adjust the basicity ratio (the molar ratio of basic to acid oxides) enables tapping the furnace without resorting to extreme temperatures, but adds to the waste volume. Improved characterization of wastes will permit adjusting the basicity ratio to between 0.7 and 1.0 by blending of wastes and/or changing the waste-soil ratio. This minimizes waste form volume. Also, lower pouring temperatures will decrease electrode and refractory attrition, reduce vaporization from the melt, and, with suitable flux, facilitate crystallization. Results of laboratory tests were favorable and pilot-scale melts are planned; however, samples have not yet been subjected to leach testing.

  17. GREENHOUSE GASES REDUCTION THROUGH WASTE MANAGEMENT IN CROATIA

    Directory of Open Access Journals (Sweden)

    Aleksandra Anić Vučinić

    2010-01-01

    Full Text Available The climate change policy is one of the key factors in the achievement of sustainable development in the Republic of Croatia. Control and mitigation of green house gases is correlated with all economy activities. Waste management is one of the main tasks of environmental protection in Croatia. The Waste Management Strategy of the Republic of Croatia and the Waste Management Plan in the Republic of Croatia define the concept of waste management hierarchy and direct and indirect measures as criteria for sustainable waste management establishment. The main constituent of this system is avoiding and minimizing waste, as well as increasing the recycling and recovery level of waste and land fill gas, which also represent green house gases mitigation measures. The Waste Management Plan consists of several direct and indirect measures for green house gases emission reduction and their implementation also affects the green house gases emissions. The contribution of the methane emission from land fills amounts to about 2% of the total green house gases emissions in Croatia. The climate change control and mitigation measures as an integral part of waste management sector strategies represent the measures of achieving the national objectives to wards green house gases emission reduction which Croatia has accepted in the frame work of the Kyoto Protocol.

  18. Business waste prevention: a review of the evidence.

    Science.gov (United States)

    Wilson, David C; Parker, David; Cox, Jayne; Strange, Kit; Willis, Peter; Blakey, Nick; Raw, Lynn

    2012-09-01

    Waste prevention is a policy priority in many countries. For example, European Union member states are currently required to prepare a national Waste Prevention Programme. This article reports on a major international review of the evidence base for business waste prevention to underpin such policy-making. A strict definition of waste prevention is used, including waste avoidance, waste reduction at source or in process, and product reuse-recycling is outside the scope of this article. The review was organised with two key dimensions. Eight types of policy intervention were identified: standards, labelling, procurement, commitments and voluntary agreements, communication, incentives, waste minimisation clubs and other business support. Six illustrative sectors were selected: construction and demolition, food and drink, hospitality, retail, automotive and office-based services. Four broad approaches to business waste prevention have been distinguished and used as part of the analytical framework, classified into a two by two matrix, using supply- and demand-side drivers as one axis, and incremental versus radical change as the other. A fundamental focus was on attitudes and behaviours. A conceptual framework is presented to navigate the various behavioural influences on businesses, and to discuss those motivations and barriers for which the evidence is relatively robust. The results suggest that the (financial) benefits to business of waste prevention are potentially huge, and that some progress is being made, but measurement is a challenge. A taster of some of the learnings on the effectiveness of the different policy interventions to promote waste prevention is also presented.

  19. Present status of recycling waste mobile phones in China: a review.

    Science.gov (United States)

    Li, Jingying; Ge, Zhongying; Liang, Changjin; An, Ni

    2017-07-01

    A large number of waste mobile phones have already been generated and are being generated. Various countries around the world have all been positively exploring the way of recycling and reuse when facing such a large amount of waste mobile phones. In some countries, processing waste mobile phones has been forming a complete industrial chain, which can not only recycle waste mobile phones to reduce their negative influence on the environment but also turn waste into treasure to acquire economic benefits dramatically. However, the situation of recycling waste mobile phones in China is not going well. Waste mobile phones are not formally covered by existing regulations and policies for the waste electric and electronic equipment in China. In order to explore an appropriate system to recover waste mobile phones, the mobile phone production and the amount of waste mobile phones are introduced in this paper, and status of waste mobile phones recycling is described; then, the disposal technology of electronic waste that would be most likely to be used for processing of electronic waste in industrial applications in the near future is reviewed. Finally, rationalization proposals are put forward based on the current recovery status of waste mobile phones for the purpose of promoting the development of recycling waste mobile phones in developing countries with a special emphasis on China.

  20. Secondary waste form testing : ceramicrete phosphate bonded ceramics.

    Energy Technology Data Exchange (ETDEWEB)

    Singh, D.; Ganga, R.; Gaviria, J.; Yusufoglu, Y. (Nuclear Engineering Division); ( ES)

    2011-06-21

    binder components from the waste form surface. Waste forms for ANS 16.1 leach testing contained appropriate amounts of rhenium and iodine as radionuclide surrogates, along with the additives silver-loaded zeolite and tin chloride. The leachability index for Re was found to range from 7.9 to 9.0 for all the samples evaluated. Iodine was below detection limit (5 ppb) for all the leachate samples. Further, leaching of sodium was low, as indicated by the leachability index ranging from 7.6-10.4, indicative of chemical binding of the various chemical species. Target leachability indices for Re, I, and Na were 9, 11, and 6, respectively. Degradation was observed in some of the samples post 90-day ANS 16.1 tests. Toxicity characteristic leaching procedure (TCLP) results showed that all the hazardous contaminants were contained in the waste, and the hazardous metal concentrations were below the Universal Treatment Standard limits. Preliminary scale-up (2-gal waste forms) was conducted to demonstrate the scalability of the Ceramicrete process. Use of minimal amounts of boric acid as a set retarder was used to control the working time for the slurry. Flexibility in treating waste streams with wide ranging compositional make-ups and ease of process scale-up are attractive attributes of Ceramicrete technology.

  1. Melt processed crystalline ceramic waste forms for advanced nuclear fuel cycles: CRP T21027 1813: Processing technologies for high level waste, formulation of matrices and characterization of waste forms, task 17208: Final report

    Energy Technology Data Exchange (ETDEWEB)

    Amoroso, J. W. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Marra, J. C. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

    2015-08-26

    A multi-phase ceramic waste form is being developed at the Savannah River National Laboratory (SRNL) for treatment of secondary waste streams generated by reprocessing commercial spent nuclear. The envisioned waste stream contains a mixture of transition, alkali, alkaline earth, and lanthanide metals. Ceramic waste forms are tailored (engineered) to incorporate waste components as part of their crystal structure based on knowledge from naturally found minerals containing radioactive and non-radioactive species similar to the radionuclides of concern in wastes from fuel reprocessing. The ability to tailor ceramics to mimic naturally occurring crystals substantiates the long term stability of such crystals (ceramics) over geologic timescales of interest for nuclear waste immobilization [1]. A durable multi-phase ceramic waste form tailored to incorporate all the waste components has the potential to broaden the available disposal options and thus minimize the storage and disposal costs associated with aqueous reprocessing. This report summarizes results from three years of work on the IAEA Coordinated Research Project on “Processing technologies for high level waste, formulation of matrices and characterization of waste forms” (T21027), and specific task “Melt Processed Crystalline Ceramic Waste Forms for Advanced Nuclear Fuel Cycles” (17208).

  2. Melt processed crystalline ceramic waste forms for advanced nuclear fuel cycles: CRP T21027 1813: Processing technologies for high level waste, formulation of matrices and characterization of waste forms, Task 17208: Final report

    Energy Technology Data Exchange (ETDEWEB)

    Amoroso, J. W. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Marra, J. C. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

    2015-08-26

    A multi-phase ceramic waste form is being developed at the Savannah River National Laboratory (SRNL) for treatment of secondary waste streams generated by reprocessing commercial spent nuclear. The envisioned waste stream contains a mixture of transition, alkali, alkaline earth, and lanthanide metals. Ceramic waste forms are tailored (engineered) to incorporate waste components as part of their crystal structure based on knowledge from naturally found minerals containing radioactive and non-radioactive species similar to the radionuclides of concern in wastes from fuel reprocessing. The ability to tailor ceramics to mimic naturally occurring crystals substantiates the long term stability of such crystals (ceramics) over geologic timescales of interest for nuclear waste immobilization [1]. A durable multi-phase ceramic waste form tailored to incorporate all the waste components has the potential to broaden the available disposal options and thus minimize the storage and disposal costs associated with aqueous reprocessing. This report summarizes results from three years of work on the IAEA Coordinated Research Project on “Processing technologies for high level waste, formulation of matrices and characterization of waste forms” (T21027), and specific task “Melt Processed Crystalline Ceramic Waste Forms for Advanced Nuclear Fuel Cycles” (17208).

  3. Waste Management Technical Manual

    Energy Technology Data Exchange (ETDEWEB)

    Buckingham, J.S. [ed.

    1967-08-31

    This Manual has been prepared to provide a documented compendium of the technical bases and general physical features of Isochem Incorporated`s Waste Management Program. The manual is intended to be used as a means of training and as a reference handbook for use by personnel responsible for executing the Waste Management Program. The material in this manual was assembled by members of Isochem`s Chemical Processing Division, Battelle Northwest Laboratory, and Hanford Engineering Services between September 1965 and March 1967. The manual is divided into the following parts: Introduction, contains a summary of the overall Waste Management Program. It is written to provide the reader with a synoptic view and as an aid in understanding the subsequent parts; Feed Material, contains detailed discussion of the type and sources of feed material used in the Waste Management Program, including a chapter on nuclear reactions and the formation of fission products; Waste Fractionization Plant Processing, contains detailed discussions of the processes used in the Waste Fractionization Plant with supporting data and documentation of the technology employed; Waste Fractionization Plant Product and Waste Effluent Handling, contains detailed discussions of the methods of handling the product and waste material generated by the Waste Fractionization Plant; Plant and Equipment, describes the layout of the Waste Management facilities, arrangement of equipment, and individual equipment pieces; Process Control, describes the instruments and analytical methods used for process control; and Safety describes process hazards and the methods used to safeguard against them.

  4. Introduction to Waste Engineering

    DEFF Research Database (Denmark)

    Christensen, Thomas Højlund

    2011-01-01

    Solid waste management as introduced in Chapter 1.1 builds in many ways on engineering. Waste engineering here means the skills and ability to understand quantitatively how a waste management system works in such a detail that waste management can be planned, facilities can be designed and sited...... and systems can be operated in a way that is environmentally sound, technical feasible, economically efficient and socially acceptable. This applies to all scales of relevance: (1) national surveys of energy use and material flows determining the frame for politically setting goals in waste management, (2......) regional plans for waste management, including (3) the selection of main management technologies and siting of facilities, (4) the design of individual technological units and, for example, (5) the operation of recycling schemes within a municipality. This chapter gives an introduction to waste engineering...

  5. [Minimally invasive approach for cervical spondylotic radiculopathy].

    Science.gov (United States)

    Ding, Liang; Sun, Taicun; Huang, Yonghui

    2010-01-01

    To summarize the recent minimally invasive approach for cervical spondylotic radiculopathy (CSR). The recent literature at home and abroad concerning minimally invasive approach for CSR was reviewed and summarized. There were two techniques of minimally invasive approach for CSR at present: percutaneous puncture techniques and endoscopic techniques. The degenerate intervertebral disc was resected or nucleolysis by percutaneous puncture technique if CSR was caused by mild or moderate intervertebral disc herniations. The cervical microendoscopic discectomy and foraminotomy was an effective minimally invasive approach which could provide a clear view. The endoscopy techniques were suitable to treat CSR caused by foraminal osteophytes, lateral disc herniations, local ligamentum flavum thickening and spondylotic foraminal stenosis. The minimally invasive procedure has the advantages of simple handling, minimally invasive and low incidence of complications. But the scope of indications is relatively narrow at present.

  6. Minimal Cells-Real and Imagined.

    Science.gov (United States)

    Glass, John I; Merryman, Chuck; Wise, Kim S; Hutchison, Clyde A; Smith, Hamilton O

    2017-12-01

    A minimal cell is one whose genome only encodes the minimal set of genes necessary for the cell to survive. Scientific reductionism postulates the best way to learn the first principles of cellular biology would be to use a minimal cell in which the functions of all genes and components are understood. The genes in a minimal cell are, by definition, essential. In 2016, synthesis of a genome comprised of only the set of essential and quasi-essential genes encoded by the bacterium Mycoplasma mycoides created a near-minimal bacterial cell. This organism performs the cellular functions common to all organisms. It replicates DNA, transcribes RNA, translates proteins, undergoes cell division, and little else. In this review, we examine this organism and contrast it with other bacteria that have been used as surrogates for a minimal cell. Copyright © 2017 Cold Spring Harbor Laboratory Press; all rights reserved.

  7. Bioleach: a mathematical model for the joint evaluation of leachate and biogas production in urban solid waste landfills

    Science.gov (United States)

    Rodrigo-Clavero, Maria-Elena; Rodrigo-Ilarri, Javier

    2017-04-01

    One of the most serious environmental problems in modern societies is the management and disposal of urban solid waste (MSW). Despite the efforts of the administration to promote recycling and reuse policies and energy recovery technologies, nowadays the majority of MSW still is disposed in sanitary landfills. During the phases of operation and post-closure maintenance of any solid waste disposal site, two of the most relevant problems are the production of leachate and the generation of biogas. The leachate and biogas production formation processes occur simultaneously over time and are coupled together through the consumption and/or production of water. However, no mathematical models have been easily identified that allow to the evaluation of the joint production of leachate and biogas, during the operational and the post-closure phase of an urban waste landfill. This paper introduces BIOLEACH, a new mathematical model programmed on a monthly scale, that evaluates the joint production of leachate and biogas applying water balance techniques and considers the management of the landfill as a bioreactor. The application of such a model on real landfills allows to perform an environmentally sustainable management that minimizes the environmental impacts produced being also economically more profitable.

  8. Efficiency Effects of Unit-based Pricing Systems and Institutional Choices of Waste Collection

    NARCIS (Netherlands)

    Dijkgraaf, E.; Gradus, R.H.J.M.

    2015-01-01

    Municipal residential waste costs are rising. Therefore, it is important to introduce measures that lower waste collection and disposal costs. Based on a large panel data set for the Netherlands we show that unit-based pricing systems are more important from a cost-minimizing point of view than the

  9. Material Life Cycle Analysis for the Reduction of Waste Generation at Military Installations

    Science.gov (United States)

    2017-02-01

    term as any practice that: 1. reduces the amount of any hazardous substance , pollutant , or con- taminant entering any waste stream or otherwise...the environment associated with the release of such substances , pollutants , or contaminants. The term includes equipment or technology...the Federal government. The Federal Pollution Prevention Act of 1990 (PPA 1990), which covers waste minimization as source reduction, defines the

  10. Utilization of various industrial wastes for the production of poly-b ...

    African Journals Online (AJOL)

    Considering the industrial interest of poly-b-hydroxy butyrate (PHB) and its high production cost, work has been undertaken for the production of PHB by Alcaligenes eutrophus. Different industrial wastes (malt, soya, sesame, molasses, bagasse and pharmaceutical waste) were used as a cheap substrate to minimize the ...

  11. The anaerobic digestion of solid organic waste.

    Science.gov (United States)

    Khalid, Azeem; Arshad, Muhammad; Anjum, Muzammil; Mahmood, Tariq; Dawson, Lorna

    2011-08-01

    The accumulation of solid organic waste is thought to be reaching critical levels in almost all regions of the world. These organic wastes require to be managed in a sustainable way to avoid depletion of natural resources, minimize risk to human health, reduce environmental burdens and maintain an overall balance in the ecosystem. A number of methods are currently applied to the treatment and management of solid organic waste. This review focuses on the process of anaerobic digestion which is considered to be one of the most viable options for recycling the organic fraction of solid waste. This manuscript provides a broad overview of the digestibility and energy production (biogas) yield of a range of substrates and the digester configurations that achieve these yields. The involvement of a diverse array of microorganisms and effects of co-substrates and environmental factors on the efficiency of the process has been comprehensively addressed. The recent literature indicates that anaerobic digestion could be an appealing option for converting raw solid organic wastes into useful products such as biogas and other energy-rich compounds, which may play a critical role in meeting the world's ever-increasing energy requirements in the future. Copyright © 2011 Elsevier Ltd. All rights reserved.

  12. Waste Generation and Recycling: Comparison of Conventional and Industrialized Building Systems

    OpenAIRE

    Rawshan A. Begum; Siti K. Satari; Joy J. Pereira

    2010-01-01

    Problem statement: In the Malaysian construction industry, there is a pressing issue of minimizing construction waste, which cause significant impacts on the environment. With the increasing demand for major infrastructure projects, commercial buildings and housing development programmers, a large amount of construction waste is being produced. Adoption of prefabrication and industrialized building systems is now a priority in the industry and also an important means of reducing waste. Approa...

  13. PROPERTIES ANALYSIS OF WASTE PLASTIC OIL AND SIZE MEASUREMENT OF NANO PARTICLE (ALUMINIUM OXIDE)

    OpenAIRE

    Ashin J C*, P Vijayabalan, Viswanath K Kaimal

    2016-01-01

    Environment concerns and depletion of petroleum fuels have created a need for the search fuels for internal combustion engines. Transformation of waste to energy is one of the recent trends in minimizing not only the waste disposal but also could be used as another fuel for internal combustion engines. Plastics are vitally necessary materials in the modern world and application in the industrial field is continually increasing. In this context, waste plastic are currently receiving renewed in...

  14. A dual-chamber pacing mode to minimize ventricular pacing

    Directory of Open Access Journals (Sweden)

    Peter Rakovec

    2005-12-01

    Full Text Available Background: Though patients with sick sinus syndrome theoretically need an atrial pacemaker only, they usually receive a ventricular or a dual-chamber pacemaker because of possible developement of atrioventricular conduction abnormalities. Right ventricular pacing produces left bundle branch block (i.e. pacing-induced ventricular desynchronization, promoting heart failure and atrial fibrillation. This problem can be solved by a special pacing mode which on one hand preserves the safety of dual-chamber pacing and on the other hand minimizes right ventricular pacing.

  15. Heart bypass surgery - minimally invasive - discharge

    Science.gov (United States)

    Minimally invasive direct coronary artery bypass - discharge; MIDCAB - discharge; Robot assisted coronary artery bypass - discharge; RACAB - discharge; Keyhole heart surgery - discharge; Coronary artery disease - MIDCAB discharge; CAD - ...

  16. Minimally invasive approaches to the cervical spine.

    Science.gov (United States)

    Celestre, Paul C; Pazmiño, Pablo R; Mikhael, Mark M; Wolf, Christopher F; Feldman, Lacey A; Lauryssen, Carl; Wang, Jeffrey C

    2012-01-01

    Minimally invasive approaches and operative techniques are becoming increasingly popular for the treatment of cervical spine disorders. Minimally invasive spine surgery attempts to decrease iatrogenic muscle injury, decrease pain, and speed postoperative recovery with the use of smaller incisions and specialized instruments. This article explains in detail minimally invasive approaches to the posterior spine, the techniques for posterior cervical foraminotomy and arthrodesis via lateral mass screw placement, and anterior cervical foraminotomy. Complications are also discussed. Additionally, illustrated cases are presented detailing the use of minimally invasive surgical techniques. Copyright © 2012 Elsevier Inc. All rights reserved.

  17. Reducing the tritium inventory in waste produced by fusion devices

    Energy Technology Data Exchange (ETDEWEB)

    Pamela, J., E-mail: jerome.pamela@cea.fr [CEA, Agence ITER-France, F-13108 Saint-Paul-lez-Durance (France); Decanis, C. [CEA, DEN, Centre de Cadarache, F-13108 Saint-Paul-lez-Durance (France); Canas, D. [CEA, DEN/DADN, Centre de Saclay, F-91191 Gif-sur-Yvette cedex (France); Liger, K.; Gaune, F. [CEA, DEN, Centre de Cadarache, F-13108 Saint-Paul-lez-Durance (France)

    2015-04-15

    Highlights: • Fusion devices including ITER will generate tritiated waste, some of which will need to be detritiated before disposal. • Interim storage is the reference solution offering an answer for all types of tritiated radwaste. • Incineration is very attractive for VLLW and possibly SL-LILW soft housekeeping waste, since it offers higher tritium and waste volume reduction than the alternative thermal treatment technique. • For metallic waste, further R&D efforts should be made to optimize tritium release management and minimize the need for interim storage. - Abstract: The specific issues raised by tritiated waste resulting from fusion machines are described. Of the several categories of tritium contaminated waste produced during the entire lifespan of a fusion facility, i.e. operating phase and dismantling phase, only two categories are considered here: metal components and solid combustible waste, especially soft housekeeping materials. Some of these are expected to contain a high level of tritium, and may therefore need to be processed using a detritiation technique before disposal or interim storage. The reference solution for tritiated waste management in France is a 50-year temporary storage for tritium decay, with options for reducing the tritium content as alternatives or complement. An overview of the strategic issues related to tritium reduction techniques is proposed for each radiological category of waste for both metallic and soft housekeeping waste. For this latter category, several options of detritiation techniques by thermal treatment like heating up or incineration are described. A comparison has been made between these various technical options based on several criteria: environment, safety, technical feasibility and costs. For soft housekeeping waste, incineration is very attractive for VLLW and possibly SL-LILW. For metallic waste, further R&D efforts should be conducted.

  18. Cleaning Up Electronic Waste (E-Waste)

    Science.gov (United States)

    While accurate data on the amount of e-waste being exported from the U.S. are not available, the United States government is concerned that these exports are being mismanaged abroad, causing serious public health and environmental hazards.

  19. Guidelines for generators to meet HWHF acceptance requirements for hazardous, radioactive, and mixed wastes at Berkeley Lab. Revision 3

    Energy Technology Data Exchange (ETDEWEB)

    Albert, R.

    1996-06-01

    This document provides performance standards that one, as a generator of hazardous chemical, radioactive, or mixed wastes at the Berkeley Lab, must meet to manage their waste to protect Berkeley Lab staff and the environment, comply with waste regulations and ensure the continued safe operation of the workplace, have the waste transferred to the correct Waste Handling Facility, and enable the Environment, Health and Safety (EH and S) Division to properly pick up, manage, and ultimately send the waste off site for recycling, treatment, or disposal. If one uses and generates any of these wastes, one must establish a Satellite Accumulation Area and follow the guidelines in the appropriate section of this document. Topics include minimization of wastes, characterization of the wastes, containers, segregation, labeling, empty containers, and spill cleanup and reporting.

  20. TSA waste stream and final waste form composition

    Energy Technology Data Exchange (ETDEWEB)

    Grandy, J.D.; Eddy, T.L.; Anderson, G.L.

    1993-01-01

    A final vitrified waste form composition, based upon the chemical compositions of the input waste streams, is recommended for the transuranic-contaminated waste stored at the Transuranic Storage Area of the Radioactive Waste Management Complex at the Idaho National Engineering Laboratory. The quantities of waste are large with a considerable uncertainty in the distribution of various waste materials. It is therefore impractical to mix the input waste streams into an ``average`` transuranic-contaminated waste. As a result, waste stream input to a melter could vary widely in composition, with the potential of affecting the composition and properties of the final waste form. This work examines the extent of the variation in the input waste streams, as well as the final waste form under conditions of adding different amounts of soil. Five prominent Rocky Flats Plant 740 waste streams are considered, as well as nonspecial metals and the ``average`` transuranic-contaminated waste streams. The metals waste stream is the most extreme variation and results indicate that if an average of approximately 60 wt% of the mixture is soil, the final waste form will be predominantly silica, alumina, alkaline earth oxides, and iron oxide. This composition will have consistent properties in the final waste form, including high leach resistance, irrespective of the variation in waste stream. For other waste streams, much less or no soil could be required to yield a leach resistant waste form but with varying properties.

  1. Solid Waste Management Plan. Revision 4

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-04-26

    The waste types discussed in this Solid Waste Management Plan are Municipal Solid Waste, Hazardous Waste, Low-Level Mixed Waste, Low-Level Radioactive Waste, and Transuranic Waste. The plan describes for each type of solid waste, the existing waste management facilities, the issues, and the assumptions used to develop the current management plan.

  2. Making the Most of Minimalism in Music.

    Science.gov (United States)

    Geiersbach, Frederick J.

    1998-01-01

    Describes the minimalist movement in music. Discusses generations of minimalist musicians and, in general, the minimalist approach. Considers various ways that minimalist strategies can be integrated into the music classroom focusing on (1) minimalism and (2) student-centered composition and principles of minimalism for use with elementary band…

  3. The relative volume growth of minimal submanifolds

    DEFF Research Database (Denmark)

    Markvorsen, Steen; Palmer, V.

    2002-01-01

    The volume growth of certain well-defined subsets of minimal submanifolds in riemannian spaces are compared with the volume growth of balls and spheres ill space forms of constant curvature.......The volume growth of certain well-defined subsets of minimal submanifolds in riemannian spaces are compared with the volume growth of balls and spheres ill space forms of constant curvature....

  4. Specialized minimal PDFs for optimized LHC calculations

    NARCIS (Netherlands)

    Carrazza, Stefano; Forte, Stefano; Kassabov, Zahari; Rojo, Juan

    2016-01-01

    We present a methodology for the construction of parton distribution functions (PDFs) designed to provide an accurate representation of PDF uncertainties for specific processes or classes of processes with a minimal number of PDF error sets: specialized minimal PDF sets, or SM-PDFs. We construct

  5. A new model of Random Regret Minimization

    NARCIS (Netherlands)

    Chorus, C.G.

    2010-01-01

    A new choice model is derived, rooted in the framework of Random Regret Minimization (RRM). The proposed model postulates that when choosing, people anticipate and aim to minimize regret. Whereas previous regret-based discrete choice-models assume that regret is experienced with respect to only the

  6. Flattening the inflaton potential beyond minimal gravity

    Science.gov (United States)

    Lee, Hyun Min

    2018-01-01

    We review the status of the Starobinsky-like models for inflation beyond minimal gravity and discuss the unitarity problem due to the presence of a large non-minimal gravity coupling. We show that the induced gravity models allow for a self-consistent description of inflation and discuss the implications of the inflaton couplings to the Higgs field in the Standard Model.

  7. Waste statistics 2004

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2006-04-07

    The 2004 reporting to the ISAG comprises 394 plants owned by 256 enterprises. In 2003, reports covered 403 plants owned by 273 enterprises. Waste generation in 2004 is compared to targets for 2008 in the government's Waste Strategy 2005-2008. The following summarises waste generation in 2004: 1) In 2004, total reported waste arisings amounted to 13,359,000 tonnes, which is 745,000 tonnes, or 6 per cent, more than in 2003. 2) If amounts of residues from coal-fired power plants are excluded from statistics, waste arisings in 2004 were 12,179,000 tonnes, which is a 9 per cent increase from 2003. 3) If amounts of residues from coal-fired power plants and waste from the building and construction sector are excluded from statistics, total waste generation in 2004 amounted to 7,684,000 tonnes, which is 328,000 tonnes, or 4 per cent, more than in 2002. In other words, there has been an increase in total waste arisings, if residues and waste from building and construction are excluded. Waste from the building and construction sector is more sensitive to economic change than most other waste. 4) The total rate of recycling was 65 per cent. The 2008 target for recycling is 65 per cent. The rate of recycling in 2003 was also 65 per cent. 5) The total amount of waste led to incineration amounted to 26 per cent, plus an additional 1 per cent left in temporary storage to be incinerated at a later time. The 2008 target for incineration is 26 per cent. These are the same percentage figures as applied to incineration and storage in 2003. 6) The total amount of waste led to landfills amounted to 8 per cent, which is one percentage point better than the overall landfill target of a maximum of 9 per cent landfilling in 2008. Also in 2003, 8 per cent of the waste was landfilled. 7) The targets for treatment of waste from individual sectors are still not being met: too little waste from households and the service sector is being recycled, and too much waste from industry is being

  8. Visual Tracking Using L2 Minimization

    Directory of Open Access Journals (Sweden)

    Pei Zhijun

    2016-01-01

    Full Text Available Visual tracking has been an active research topic in the computer vision applications. By modeling the target appearance with a sparse approximation over a template set, sparse representation has been applied to the visual tracker, which called L1 tracker. Due to the need to solve the L1 norm related minimization problem for many times, this L1 tracker is very computationally demanding. Although various fast numerical solver is developed to solve the resulting L1 norm related minimization problem, the framework is still a L1 norm related minimization model. Similar to the face recognition problem, sparse approximations may not deliver the desired robustness and a simple L2 approach to the visual tracking problem is not only robust, but also much faster. It may be possible to apply the L2 minimization, instead of L1 minimization, to the visual tracking problems, which has been verified by experiments on challenging sequences in the paper.

  9. Optimal Control of Diesel Engines with Waste Heat Recovery System

    NARCIS (Netherlands)

    Willems, F.P.T.; Donkers, M.C.F.; Kupper, F.

    2014-01-01

    This study presents an integrated energy and emission management strategy for a Euro-VI diesel engine with Waste Heat Recovery (WHR) system. This Integrated Powertrain Control (IPC) strategy optimizes the CO2-NOx trade-off by minimizing the operational costs associated with fuel and AdBlue

  10. Valorization of food waste into hydroxymethylfurfural: Dual role of metal ions in successive conversion steps.

    Science.gov (United States)

    Yu, Iris K M; Tsang, Daniel C W; Yip, Alex C K; Chen, Season S; Ok, Yong Sik; Poon, Chi Sun

    2016-11-01

    This study aimed to transform food waste into a value-added chemical, hydroxymethylfurfural (HMF), and unravel the tangled effects induced by the metal catalysts on each single step of the successive conversion pathway. The results showed that using cooked rice and bread crust as surrogates of starch-rich food waste, yields of 8.1-9.5% HMF and 44.2-64.8% glucose were achieved over SnCl4 catalyst. Protons released from metal hydrolysis and acidic by-products rendered Brønsted acidity to catalyze fructose dehydration and hydrolysis of glycosidic bond. Lewis acid site of metals could facilitate both fructose dehydration and glucose isomerization via promoting the rate-limiting internal hydride shift, with the catalytic activity determined by its electronegativity, electron configuration, and charge density. Lewis acid site of a higher valence also enhanced hydrolysis of polysaccharide. However, the metals also catalyzed undesirable polymerization possibly by polarizing the carbonyl groups of sugars and derivatives, which should be minimized by process optimization. Copyright © 2016 Elsevier Ltd. All rights reserved.

  11. Survey the Waste Management of Qom City in 2014

    Directory of Open Access Journals (Sweden)

    Mahdi Farzadkia

    2015-06-01

    Full Text Available Background and objectives: Lack of proper management, increasing waste production and non-normative disposal of waste in addition to misspend the national capital, cause loss of precious natural resources. To address this problem we need a coherent and dynamic management program. The goal of this project is to reduce environmental pollution, cost saving, promoting citizen participation, revenue and reduce land loss. Methods: In this study, check lists, interviews and field report were used to collect data at period of one year. To determine the waste components, sampling technique was used then sampling data was imported into Excel software and was analyzed. Results: At the beginning of the project, the average per capita of generated waste was 580 g/day and at the end of the project will 660 g/day. The waste materials determined as %66.8 putrescible, %4.3 paper and cardboard, %7.2 plastic, %2.3 glass, %2 textiles, %0.2 metals, %1.6 wood, and also, hospital waste was equal to 4400 Kg. According to estimates made annual cost of solid waste management services per capita in Qom is 70 Rial and the cost of collection, transportation, separation and disposal of garbage for every Kilogram per day is 280 Rial. Conclusion: Amount of waste per capita in Qom was less than of Tehran, Delijan and Mallayer cities, and more than Esfahan and Kashan cities. Hospital waste was desirable as compared to the average of Iran.

  12. Projected Salt Waste Production from a Commercial Pyroprocessing Facility

    Directory of Open Access Journals (Sweden)

    Michael F. Simpson

    2013-01-01

    Full Text Available Pyroprocessing of used nuclear fuel inevitably produces salt waste from electrorefining and/or oxide reduction unit operations. Various process design characteristics can affect the actual mass of such waste produced. This paper examines both oxide and metal fuel treatment, estimates the amount of salt waste generated, and assesses potential benefit of process options to mitigate the generation of salt waste. For reference purposes, a facility is considered in which 100 MT/year of fuel is processed. Salt waste estimates range from 8 to 20 MT/year from considering numerous scenarios. It appears that some benefit may be derived from advanced processes for separating fission products from molten salt waste, but the degree of improvement is limited. Waste form production is also considered but appears to be economically unfavorable. Direct disposal of salt into a salt basin type repository is found to be the most promising with respect to minimizing the impact of waste generation on the economic feasibility and sustainability of pyroprocessing.

  13. Policy gridlock in waste management: Balancing federal and state concerns

    Energy Technology Data Exchange (ETDEWEB)

    Feldman, D.L. [Oak Ridge National Lab., TN (United States); Peretz, J.H.; Jendrucko, B.K. [Univ. of Tennessee, Knoxville, TN (United States)

    1993-12-31

    Current federal hazardous and low-level radioactive waste management policies fail to balance national concerns for policy consistency with state concerns for equity, discretion, and adequate resources. Failure to balance these competing values has resulted in {open_quotes}policy gridlock{close_quotes} - exemplified by conflicts over the Resource Conservation and Recovery Act and the Low-Level Radioactive Waste Policy Acts. Both conflicts have resulted in recent U.S. Supreme Court litigation. After reviewing federal-state conflict in hazardous and low-level radioactive waste management, we propose that the solution to gridlock lies in modifying conjoint federalism. Conjoint federalism allows for joint responsibility for waste policy between federal and state governments, with state programs meeting minimum standards set by federal programs. However, conjoint federalism does not currently allow for sufficient state discretion, which is paramount for successful waste management programs. Specifically, Congress should expand conjoint federalism, to allow states to charge differential fees on imported hazardous waste as is done for low-level radioactive waste. This expansion would encourage waste minimization and better interstate planning.

  14. Ceramics in nuclear waste management

    Energy Technology Data Exchange (ETDEWEB)

    Chikalla, T D; Mendel, J E [eds.

    1979-05-01

    Seventy-three papers are included, arranged under the following section headings: national programs for the disposal of radioactive wastes, waste from stability and characterization, glass processing, ceramic processing, ceramic and glass processing, leaching of waste materials, properties of nuclear waste forms, and immobilization of special radioactive wastes. Separate abstracts were prepared for all the papers. (DLC)

  15. Operational Waste Volume Projection

    Energy Technology Data Exchange (ETDEWEB)

    STRODE, J.N.

    1999-08-24

    Waste receipts to the double-shell tank system are analyzed and wastes through the year 2018 are projected based on assumption as of July 1999. A computer simulation of site operations is performed, which results in projections of tank fill schedules, tank transfers, evaporator operations, tank retrieval, and aging waste tank usage. This projection incorporates current budget planning and the clean-up schedule of the Tri-Party Agreement.

  16. Operational waste volume projection

    Energy Technology Data Exchange (ETDEWEB)

    Koreski, G.M.

    1996-09-20

    Waste receipts to the double-shell tank system are analyzed and wastes through the year 2015 are projected based on generation trends of the past 12 months. A computer simulation of site operations is performed, which results in projections of tank fill schedules, tank transfers, evaporator operations, tank retrieval, and aging waste tank usage. This projection incorporates current budget planning and the clean-up schedule of the Tri-Party Agreement. Assumptions were current as of June 1996.

  17. Let’s limit our waste production and let’s’ sort it!

    CERN Multimedia

    HSE Unit

    2013-01-01

    Let’s limit our waste production! – Why ? Preventing the production of waste is the best solution to avoid environmental issues, economic impacts and technical constraints. So, whenever you are involved in the design, manufacturing, distribution, use or dismantling of a product or an activity in general, always remember that the best waste is that which is not produced. The limitation of waste production being an HSE objective declared in 2013 by the CERN Director-General, we encourage everyone to help limit the amount of waste produced through CERN activities. Let’s sort it! – Why ? Since the 90s, CERN has implemented a policy to promote recovery of the waste* generated by its activities. Nowadays, CERN is committed to continuously improving its sorting and recovery and therefore various initiatives have been started by GS-IS to improve the recovery of waste (e.g. recovery of organic waste from restaurants; implementation of solar trash compactors - see Bulletin 27-...

  18. Thermal plasma technology for the treatment of wastes: a critical review.

    Science.gov (United States)

    Gomez, E; Rani, D Amutha; Cheeseman, C R; Deegan, D; Wise, M; Boccaccini, A R

    2009-01-30

    This review describes the current status of waste treatment using thermal plasma technology. A comprehensive analysis of the available scientific and technical literature on waste plasma treatment is presented, including the treatment of a variety of hazardous wastes, such as residues from municipal solid waste incineration, slag and dust from steel production, asbestos-containing wastes, health care wastes and organic liquid wastes. The principles of thermal plasma generation and the technologies available are outlined, together with potential applications for plasma vitrified products. There have been continued advances in the application of plasma technology for waste treatment, and this is now a viable alternative to other potential treatment/disposal options. Regulatory, economic and socio-political drivers are promoting adoption of advanced thermal conversion techniques such as thermal plasma technology and these are expected to become increasingly commercially viable in the future.

  19. Glass science tutorial: Lecture No. 7, Waste glass technology for Hanford

    Energy Technology Data Exchange (ETDEWEB)

    Kruger, A.A.

    1995-07-01

    This paper presents the details of the waste glass tutorial session that was held to promote knowledge of waste glass technology and how this can be used at the Hanford Reservation. Topics discussed include: glass properties; statistical approach to glass development; processing properties of nuclear waste glass; glass composition and the effects of composition on durability; model comparisons of free energy of hydration; LLW glass structure; glass crystallization; amorphous phase separation; corrosion of refractories and electrodes in waste glass melters; and glass formulation for maximum waste loading.

  20. Innovation for achieving sustainable waste management

    DEFF Research Database (Denmark)

    Hansen, Jens Aage; Hahn, Niels Jørn

    2007-01-01

    Economic growth and the basis for welfare are depending on the ability to produce and utilise knowledge. The inherently necessary innovationproces depends on a strong education and research environment, including business (public and private) and universities. Associations such as ISWA (Internati...... (International Solid Waste Association) can promote such cooperation locally and globally. Not least poor countries will profit from such linkage to the benefit of both development and environment....