WorldWideScience

Sample records for waste metal hydroxide

  1. Waste metal hydroxide sludge as adsorbent for a reactive dye.

    Science.gov (United States)

    Santos, Sílvia C R; Vílar, Vítor J P; Boaventura, Rui A R

    2008-05-30

    An industrial waste sludge mainly composed by metal hydroxides was used as a low-cost adsorbent for removing a reactive textile dye (Remazol Brilliant Blue) in solution. Characterization of this waste material included chemical composition, pH(ZPC) determination, particle size distribution, physical textural properties and metals mobility under different pH conditions. Dye adsorption equilibrium isotherms were determined at 25 and 35 degrees C and pH of 4, 7 and 10 revealing reasonably fits to Langmuir and Freundlich models. At 25 degrees C and pH 7, Langmuir fit indicates a maximum adsorption capacity of 91.0mg/g. An adsorptive ion-exchange mechanism was identified from desorption studies. Batch kinetic experiments were also conducted at different initial dye concentration, temperature, adsorbent dosage and pH. A pseudo-second-order model showed good agreement with experimental data. LDF approximation model was used to estimate homogeneous solid diffusion coefficients and the effective pore diffusivities. Additionally, a simulated real effluent containing the selected dye, salts and dyeing auxiliary chemicals, was also used in equilibrium and kinetic experiments and the adsorption performance was compared with aqueous dye solutions.

  2. Pore size distribution, strength, and microstructure of portland cement paste containing metal hydroxide waste

    Energy Technology Data Exchange (ETDEWEB)

    Majid, Z.A.; Mahmud, H.; Shaaban, M.G.

    1996-12-31

    Stabilization/solidification of hazardous wastes is used to convert hazardous metal hydroxide waste sludge into a solid mass with better handling properties. This study investigated the pore size development of ordinary portland cement pastes containing metal hydroxide waste sludge and rice husk ash using mercury intrusion porosimetry. The effects of acre and the addition of rice husk ash on pore size development and strength were studied. It was found that the pore structures of mixes changed significantly with curing acre. The pore size shifted from 1,204 to 324 {angstrom} for 3-day old cement paste, and from 956 to 263 {angstrom} for a 7-day old sample. A reduction in pore size distribution for different curing ages was also observed in the other mixtures. From this limited study, no conclusion could be made as to any correlation between strength development and porosity. 10 refs., 6 figs., 3 tabs.

  3. 40 CFR 721.4600 - Recovered metal hydroxide.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Recovered metal hydroxide. 721.4600... Substances § 721.4600 Recovered metal hydroxide. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified generically as a recovered metal hydroxide (PMN P-91-809...

  4. Polysulfide intercalated layered double hydroxides for metal capture applications

    Energy Technology Data Exchange (ETDEWEB)

    Kanatzidis, Mercouri G.; Ma, Shulan

    2017-04-04

    Polysulfide intercalated layered double hydroxides and methods for their use in vapor and liquid-phase metal capture applications are provided. The layered double hydroxides comprise a plurality of positively charged host layers of mixed metal hydroxides separated by interlayer spaces. Polysulfide anions are intercalated in the interlayer spaces.

  5. Interaction of Pu(IV,VI) hydroxides/oxides with metal hydroxides/oxides in alkaline media

    Energy Technology Data Exchange (ETDEWEB)

    Fedoseev, A.M.; Krot, N.N.; Budantseva, N.A.; Bessonov, A.A.; Nikonov, M.V.; Grigoriev, M.S.; Garnov, A.Y.; Perminov, V.P.; Astafurova, L.N. [Russian Academy of Sciences, Moscow (Russian Federation). Inst. of Physical Chemistry

    1998-08-01

    The primary goal of this investigation was to obtain data on the possibility, extent, and characteristics of interaction of Pu(IV) and (VI) with hydroxides and oxides of d-elements and other metals [Al(III), LA(III), and U(VI)] in alkaline media. Such information is important in fundamental understanding of plutonium disposition and behavior in Hanford Site radioactive tank waste sludge. These results supply essential data for determining criticality safety and in understanding transuranic waste behavior in storage, retrieval, and treatment of Hanford Site tank waste.

  6. Hydroxide depletion in dilute supernates stored in waste tanks

    Energy Technology Data Exchange (ETDEWEB)

    Hobbs, D.T.

    1985-10-10

    Free hydroxide ion in dilute supernates are depleted by reaction with atmospheric carbon dioxide to form bicarbonate and carbonate species and by reaction with acidic compounds formed by the radiolytic decomposition of tetraphenylborate salts. A model of the kinetics and thermodynamics of absorption of carbon dioxide in the waste tanks has been developed. Forecasts of the rate of hydroxide depletion and the requirements for sodium hydroxide to maintain technical standards have been made for the washed sludge and washed precipitate storage tanks. Hydroxide depletion is predicted to have a minimal impact on sludge processing operations. However, in-tank precipitation and downstream DWPF operations are predicted to be significantly affected by hydroxide depletion in Tank 49H. The installation of a carbon dioxide scrubber on Tank 49H may be justified in view of the decrease in alkali content and variation in the melter feed.

  7. Single sheet metal oxides and hydroxides

    DEFF Research Database (Denmark)

    Huang, Lizhi

    The synthesis of layered double hydroxides (LDHs) provides a relatively easy and traditional way to build versatile chemical compounds with a rough control of the bulk structure. The delamination of LDHs to form their single host layers (2D nanosheets) and the capability to reassemble them offer ......) Delamination of the LDHs structure (oxGRC12) with the formation of single sheet iron (hydr)oxide (SSI). (3) Assembly of the new 2D nanosheets layer by layer to achieve desired functionalities....

  8. Heavy metals in municipal solid waste deposits

    Energy Technology Data Exchange (ETDEWEB)

    Flyhammar, P.

    1997-12-01

    Extensive use of heavy metals in modern society influences routes followed by fluxes on the surface of the Earth. The changed flow paths may be harmful for the balance of biological systems at different levels, micro-organisms, human beings and whole ecosystems, since the toxicity of heavy metals is determined by their concentrations and chemical forms. Despite the low mobility of heavy metals (Zn, Cu, Pb, Cr, Ni and Cd) in municipal landfills, it was found that extensive transformations of the binding forms of heavy metal take place within the waste mass during the degradation of the waste. These changes appear to be closely related to the development of early diagenetic solid phases, i.e. new secondary solid phases formed in the waste. The heavy metals often constitute a minor part of these phases and the bindings include several forms such as adsorption, complexation, coprecipitation, precipitation, etc. It was also found that the associations between heavy metals and solid phases are dominated by several binding forms to one specific substrate rather than bindings to various solid phases. The mobility of iron and manganese seems to increase during the processes involved in waste degradation due to the solution of oxide/hydroxide phases, while the heavy metals appear to become less mobile due to their binding to organic compounds and sulphides. However, one exception in this case may be nickel. Another aspect of the transformation of heavy metals is the accumulation of pools of heavy metals which can become susceptible to environmental changes, such as oxidation or acidification. However, the risk of increased mobilization caused by lower pH values seem to be limited since municipal solid waste has a large buffer capacity. 66 refs, 9 figs, 3 tabs 66 refs, 9 figs, 3 tabs

  9. Aging of trivalent metal hydroxide/oxide gels in divalent metal salt ...

    Indian Academy of Sciences (India)

    Unknown

    pH metric titrations, involving the slow addition of NaOH to a mixed metal (M2+ + M′3+) salt solution. Two pH plateaus were observed, the first corresponding to the precipita- tion of the trivalent hydroxide, 'M′(OH)3', followed by the second, which was attributed to LDH formation. By esta- blishing equilibrium after each ...

  10. Analysis of Heavy Metal in Electrocoagulated Metal Hydroxide Sludge (EMHS from the Textile Industry by Energy Dispersive X-Ray Fluorescence (EDXRF

    Directory of Open Access Journals (Sweden)

    Tanveer Mehedi Adyel

    2012-12-01

    Full Text Available Environmental pollution due to discharges of heavy metal containing sludge from textile industries is a common nuisance in Bangladesh, where no treatment of sludge is carried out before final disposals. Energy Dispersive X-ray Fluorescence (EDXRF was employed in the present study to analyze the heavy metal content of Electrocoagulated Metal Hydroxide Sludge (EMHS collected from a composite textile industry. Thirteen heavy metals, viz., Mn, Ti, Cu, Zn, Ni, Sr, V, Cr, Zr, Hg, Cd, Nb and Ga, were detected. Mn, Ni, Cu, Zn and Cd exceeded the permissible limit to apply the EMHS in agricultural land. Cr, Ni, Cu and Zn were compared to the values of the European legislation to evaluate the environmental risk and to classify the wastes as inert wastes or as wastes that have to be control landfilled. EMHS was categorized as class I and needs to be deposited in controlled landfills.

  11. Speciation of heavy metal ions as influenced by interactions with montmorillonite, Al hydroxide polymers and citrate

    NARCIS (Netherlands)

    Janssen, R.P.T.

    1995-01-01

    Clay minerals, metal-hydroxides and organic matter can bind metal ions; moreover they also interact with each other. These mutual interactions influence the metal binding to a significant extent. In this study, the speciation of the heavy metal ions Zn and Ph was investigated in model

  12. Mg/Al double-metal hydroxide regeneration of anion exchange resin by electric field intensification.

    Science.gov (United States)

    Wang, Ying; Li, Zhun; Li, Yansheng; Liu, Zhigang

    2017-03-01

    Fouled anion exchange resins were regenerated by electric field intensification of Mg/Al double-metal hydroxides. Regenerative experiments were performed with varying voltages (10-30 V) and dosages of Mg/Al hydroxides (0.045-0.135 mol and 0.015-0.045 mol, respectively) for 1-5 h. Optimal results were obtained under the following regenerative conditions: 20 V, 4 h, and 0.09/0.03 mol of Mg/Al hydroxides. The maximum regenerative capacity of resins was increased to 41.07%. The regenerative mechanism was presented by Fourier-transform infrared spectrum of resins and Mg/Al hydroxides, and the regenerative degree was analyzed with respect to conductivity, pH value, and electric current. Mg/Al hydroxides were also recycled after the regeneration. This method was proven to be cost-effective and environmentally friendly.

  13. Nuclear waste storage container with metal matrix

    Science.gov (United States)

    Sump, Kenneth R.

    1978-01-01

    The invention relates to a storage container for high-level waste having a metal matrix for the high-level waste, thereby providing greater impact strength for the waste container and increasing heat transfer properties.

  14. Two-dimensional metal oxide and metal hydroxide nanosheets: synthesis, controlled assembly and applications in energy conversion and storage

    NARCIS (Netherlands)

    ten Elshof, Johan E.; Yuan, H.; Gonzalez Rodriguez, P.

    2016-01-01

    The developments and state of the art in the research on two-dimensional nanosheets derived from layered metal oxides and layered metal hydroxides are reviewed in this paper, with emphasis on their promising applications in various new energy technologies, i.e., as supercapacitor electrodes, lithium

  15. Surface Properties of Metal Hydroxide Microparticles in the Ambient Air

    Directory of Open Access Journals (Sweden)

    Zakharenko Valery

    2017-01-01

    Full Text Available The adsorption and photoadsorption properties of Mg(OH2 and Ca(OH2 microparticles in the ambient air were investigated. The compositional analysis of an adsorption layer of microparticles was carried out. The kinetics of photodesorption of molecules from microcrystal surfaces and the interaction of HCFC-22 (CHF2Cl in the dark and under light were studied. Quantum yields and their spectral dependencies were determined for CO2 photodesorption, O2 and CO photoadsorption. The effect of weakly bound CO displacement from the surface of microparticles was revealed during dark adsorption of HCFC-22. It is supposed that adsorbed CO is formed as a result of atmospheric CO2 reduction after the break of Mg—OH bonds. In case of calcium hydroxide, CO is generated during the interaction of calcium hydroxide with carbon dioxide in the presence of water.

  16. High-temperature stabilization of polyolefines with hydroxides of alkali metals

    Energy Technology Data Exchange (ETDEWEB)

    Losev, Y.P.; Paushkin, Y.M. (V.I. Lenin Byelorussian State Univ., Universitetskii Gorodok, 220080 Minsk, Byelorussia (SU))

    1992-07-25

    This paper discusses polyolefines which are one of the main types of synthetic polymer materials. However, an important shortcoming is their low temperature resistance and heat stability, which reduce the processing efficiency and restrict their range of application. So far the study of high-temperature stabilization of polyolefines has been limited since solution of the problem involves some difficulties. In the case of polyolefine the use of stabilizers against thermal and light-oxidative degradation is not efficient since at high temperatures they easily decompose to form radical capable of initiating additional kinetic destruction chains. To date, few antioxidants and light stabilizers have been found that can partially inhibit thermal destruction of polyolefines. Hydroxides of alkali metals are shown to be high-temperature stabilizers of polyethylene. Potassium hydroxide is found to be most efficient. The reaction mechanism of alkali metal hydroxides as thermal stabilizers is considered.

  17. Pilot-scale production of biodiesel from waste fats and oils using tetramethylammonium hydroxide.

    Science.gov (United States)

    Šánek, Lubomír; Pecha, Jiří; Kolomazník, Karel; Bařinová, Michaela

    2016-02-01

    Annually, a great amount of waste fats and oils not suitable for human consumption or which cannot be further treated are produced around the world. A potential way of utilizing this low-cost feedstock is its conversion into biodiesel. The majority of biodiesel production processes today are based on the utilization of inorganic alkali catalysts. However, it has been proved that an organic base - tetramethylammonium hydroxide - can be used as a very efficient transesterification catalyst. Furthermore, it can be employed for the esterification of free fatty acids - reducing even high free fatty acid contents to the required level in just one step. The work presented herein, is focused on biodiesel production from waste frying oils and animal fats using tetramethylammonium hydroxide at the pilot-plant level. The results showed that the process performance in the pilot unit - using methanol and TMAH as a catalyst, is comparable to the laboratory procedure, even when the biodiesel is produced from waste vegetable oils or animal fats with high free fatty acid content. The reaction conditions were set at: 1.5% w/w of TMAH, reaction temperature 65°C, the feedstock to methanol molar ratio to 1:6, and the reaction time to 120min. The conversion of triglycerides to FAME was approximately 98%. The cloud point of the biodiesel obtained from waste animal fat was also determined. Copyright © 2015 Elsevier Ltd. All rights reserved.

  18. Topochemical synthesis of alkali-metal hydroxide layers within double- and triple-layered perovskites.

    Science.gov (United States)

    Montasserasadi, Dariush; Mohanty, Debasish; Huq, Ashfia; Heroux, Luke; Payzant, Edward Andrew; Wiley, John B

    2014-02-03

    The formation of alkali-metal hydroxide layers within lamellar perovskites has been accomplished by a two-step topochemical reaction strategy. Reductive intercalation of ALaNb2O7 with alkali metal (A = K, Rb) and RbCa2Nb3O10 with Rb leads to A2LaNb2O7 and Rb2Ca2Nb3O10, respectively. Oxidative intercalation with stoichiometric amounts of water vapor, produced by the decomposition of calcium oxalate monohydrate in a sealed ampule, allows the insertion hydroxide species. Compounds of the form (A2OH)LaNb2O7 (A = K, Rb) and (Rb2OH)Ca2Nb3O10 are accessible. X-ray diffraction data indicates a clear layer expansion of almost 3 Å on the insertion of hydroxide relative to that of the parent. Rietveld refinement of neutron diffraction data collected on deuterated samples of (Rb2OD)LaNb2O7 (P4/mmm space group, a = 3.9348(1) Å, c = 14.7950(7) Å) finds that both rubidium and oxygen species reside in cubic sites forming a CsCl-like interlayer structure between niobate perovskite blocks. Hydrogens, attached to the interlayer oxygens, are disordered over a 4-fold site in the x-y plane and have O-H bond distances (0.98 Å) consistent with known hydroxide species. This synthetic approach expands the library of available topochemical reactions, providing a facile method for the construction of alkali-metal hydroxide layers within receptive perovskite hosts.

  19. Regeneration of Waste Edible Oil by the Use of Virgin and Calcined Magnesium Hydroxide as Adsorbents.

    Science.gov (United States)

    Ogata, Fumihiko; Kawasaki, Naohito

    2016-01-01

    In this study, we prepared virgin (S, L) and calcined (S-380, S-1000, L-380, L-1000) magnesium hydroxide for regeneration of waste edible oil. Deterioration of soybean oil, rapeseed oil, and olive oil was achieved by heat and aeration treatment. The properties of the different adsorbents were investigated using specific surface area measurements, scanning electron microscopy, X-ray diffraction analysis, thermogravimetric-differential thermal analysis, and surface pH measurement. Moreover, the relationship between the changes in acid value (AV) and carbonyl value (CV) and the adsorbent properties were evaluated. The specific surface areas of S-380 and L-380 were greater than that of other adsorbents. In addition, the XRD results show that S-380 and L-380 contain both magnesium hydroxide and magnesium oxide structures. The decreases in AV and CV using S-380 and L-380 were greater than achieved using other adsorbents. The correlation coefficients between the decrease in AV and CV and specific surface area were 0.947 for soybean oil, 0.649 for rapeseed oil, and 0.773 for olive oil, respectively. The results obtained in this study suggest that a physical property of the adsorbent, namely specific surface area, was primarily responsible for the observed decreases in AV and CV. Overall, the results suggest that S-380 and L-380 are useful for the regeneration of waste edible oil.

  20. Retention of heavy metals on layered double hydroxides thin films deposited by pulsed laser deposition

    Energy Technology Data Exchange (ETDEWEB)

    Vlad, A., E-mail: angela.vlad@gmail.com [National Institute for Lasers, Plasma and Radiation Physics, 409 Atomistilor Str., 76900 Bucharest-Magurele (Romania); Birjega, R.; Matei, A.; Luculescu, C.; Mitu, B.; Dinescu, M. [National Institute for Lasers, Plasma and Radiation Physics, 409 Atomistilor Str., 76900 Bucharest-Magurele (Romania); Zavoianu, R.; Pavel, O.D. [University of Bucharest, Faculty of Chemistry, Department of Chemical Technology and Catalysis, 4-12 Regina Elisabeta Bd., Bucharest (Romania)

    2014-05-01

    Heavy metals are toxic and hazardous pollutants in the environment due to their nonbiodegradability and persistence, which can pose serious threats to living organisms. The ability of Mg–Al based layered double hydroxides (LDHs) thin films to retain heavy metals from aqueous solutions at different concentrations is a novel topic with prospects of attractive applications, such as detection of heavy metals. We report on the ability of a series of Mg–Al based layered double hydroxides thin films to detect Ni and Co cations in aqueous solutions. Uptake of heavy metals ions such as Ni{sup 2+}, Co{sup 2+} from aqueous solutions was studied as function of contact time at a standard metal ion concentration. The LDHs thin films were deposited using pulsed laser deposition (PLD). The different adsorption mechanisms were studied in connection with different heavy metals used as probe cations. X-ray diffraction, atomic force microscopy, scanning electron microscopy coupled with energy dispersive X-ray spectroscopy, Fourier transform infra-red spectroscopy were the techniques used for the investigation of as deposited and after heavy metals retention thin films.

  1. Retention of heavy metals on layered double hydroxides thin films deposited by pulsed laser deposition

    Science.gov (United States)

    Vlad, A.; Birjega, R.; Matei, A.; Luculescu, C.; Mitu, B.; Dinescu, M.; Zavoianu, R.; Pavel, O. D.

    2014-05-01

    Heavy metals are toxic and hazardous pollutants in the environment due to their nonbiodegradability and persistence, which can pose serious threats to living organisms. The ability of Mg-Al based layered double hydroxides (LDHs) thin films to retain heavy metals from aqueous solutions at different concentrations is a novel topic with prospects of attractive applications, such as detection of heavy metals. We report on the ability of a series of Mg-Al based layered double hydroxides thin films to detect Ni and Co cations in aqueous solutions. Uptake of heavy metals ions such as Ni2+, Co2+ from aqueous solutions was studied as function of contact time at a standard metal ion concentration. The LDHs thin films were deposited using pulsed laser deposition (PLD). The different adsorption mechanisms were studied in connection with different heavy metals used as probe cations. X-ray diffraction, atomic force microscopy, scanning electron microscopy coupled with energy dispersive X-ray spectroscopy, Fourier transform infra-red spectroscopy were the techniques used for the investigation of as deposited and after heavy metals retention thin films.

  2. Production of activated carbons from pyrolysis of waste tires impregnated with potassium hydroxide.

    Science.gov (United States)

    Teng, H; Lin, Y C; Hsu, L Y

    2000-11-01

    Activated carbons were produced from waste tires using a chemical activation method. The carbon production process consisted of potassium hydroxide (KOH) impregnation followed by pyrolysis in N2 at 600-900 degrees C for 0-2 hr. The activation method can produce carbons with a surface area (SA) and total pore volume as high as 470 m2/g and 0.57 cm3/g, respectively. The influence of different parameters during chemical activation, such as pyrolysis temperature, holding time, and KOH/tire ratio, on the carbon yield and the surface characteristics was explored, and the optimum preparation conditions were recommended. The pore volume of the resulting carbons generally increases with the extent of carbon gasified by KOH and its derivatives, whereas the SA increases with degree of gasification to reach a maximum value, and then decreases upon further gasification.

  3. Structural Differentiation between Layered Single (Ni) and Double Metal Hydroxides (Ni–Al LDHs) Using Wavelet Transformation

    Energy Technology Data Exchange (ETDEWEB)

    Siebecker, Matthew G. [University of Delaware, Delaware Environmental Institute; Sparks, Donald L. [University of Delaware, Delaware Environmental Institute

    2017-09-07

    Layered double hydroxides (LDHs) are anionic clays important in disciplines such as environmental chemistry, geochemistry, and materials science. Developments in signal processing of extended X-ray absorption fine structure (EXAFS) data, such as wavelet transformation (WT), have been used to identify transition metals and Al present in the hydroxide sheets of LDHs. The WT plots of LDHs should be distinct from those of isostructural single metal hydroxides. However, no direct comparison of these minerals appears in the literature using WT. This work systematically analyzes a suite of Ni-rich mineral standards, including Ni–Al LDHs, single metal Ni hydroxides, and Ni-rich silicates using WT. The results illustrate that the WT plots for α-Ni(OH)2 and Ni–Al LDHs are often indistinguishable from each other, with similar two-component plots for the different mineral types. This demonstrates that the WT of the first metal shell often cannot be used to differentiate an LDH from a single metal hydroxide. Interlayer anions adsorbed to the hydroxide sheet of α-Ni(OH)2 affect the EXAFS spectra and are not visible in the FT but are clearly resolved and discrete in the WT.

  4. Selective preconcentration of polynuclear aromatic hydrocarbons and polychlorinated biphenyls by in situ metal hydroxide precipitation.

    Science.gov (United States)

    Hess, G G; McKenzie, D E; Hughes, B M

    1986-09-24

    An investigation of selective concentration of analytes from aqueous samples by in situ magnesium hydroxide precipitation, as described by Faltusz, has yielded the following results: the method is selective for polycyclic aromatic hydrocarbons and polychlorinated biphenyls of higher molecular weight: it discriminates strongly against acidic molecules, and other neutral and basic molecules are only partially recovered; a variety of metal hydroxides could evidently be used in this method, but magnesium appears to have practical advantages over some of the others; the reproducibility of analyses on pure water samples is acceptable (ca.20% relative standard deviation), but the results from natural samples show lower recovery and wider variability; a preliminary test, in which this method was used to discriminate against major amounts of interfering solutes, shows promise that this technique might have unique advantages in certain situations.

  5. Metallic Nickel Hydroxide Nanosheets Give Superior Electrocatalytic Oxidation of Urea for Fuel Cells.

    Science.gov (United States)

    Zhu, Xiaojiao; Dou, Xinyu; Dai, Jun; An, Xingda; Guo, Yuqiao; Zhang, Lidong; Tao, Shi; Zhao, Jiyin; Chu, Wangsheng; Zeng, Xiao Cheng; Wu, Changzheng; Xie, Yi

    2016-09-26

    The direct urea fuel cell (DUFC) is an important but challenging renewable energy production technology, it offers great promise for energy-sustainable developments and mitigating water contamination. However, DUFCs still suffer from the sluggish kinetics of the urea oxidation reaction (UOR) owing to a 6 e(-) transfer process, which poses a severe hindrance to their practical use. Herein, taking β-Ni(OH)2 nanosheets as the proof-of-concept study, we demonstrated a surface-chemistry strategy to achieve metallic Ni(OH)2 nanosheets by engineering their electronic structure, representing a first metallic configuration of transition-metal hydroxides. Surface sulfur incorporation successfully brings synergetic effects of more exposed active sites, good wetting behavior, and effective electron transport, giving rise to greatly enhanced performance for UOR. Metallic nanosheets exhibited a much higher current density, smaller onset potential and stronger durability. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  6. ONE – STAGE METAL WASTES RECYCLING

    Directory of Open Access Journals (Sweden)

    S. L. Rovin

    2011-01-01

    Full Text Available Rotary tilting furnace is the most efficient installation for recycling of dispersible metal wastes of any alloy. Several constructions have been designed for chips heating and melting, scale recovery, ets.

  7. Studies on MgNi-Based Metal Hydride Electrode with Aqueous Electrolytes Composed of Various Hydroxides

    Directory of Open Access Journals (Sweden)

    Jean Nei

    2016-08-01

    Full Text Available Compositions of MgNi-based amorphous-monocrystalline thin films produced by radio frequency (RF sputtering with a varying composition target have been optimized. The composition Mg52Ni39Co3Mn6 is identified to possess the highest initial discharge capacity of 640 mAh·g−1 with a 50 mA·g−1 discharge current density. Reproduction in bulk form of Mg52Ni39Co3Mn6 alloy composition was prepared through a combination of melt spinning (MS and mechanical alloying (MA, shows a sponge-like microstructure with >95% amorphous content, and is chosen as the metal hydride (MH alloy for a sequence of electrolyte experiments with various hydroxides including LiOH, NaOH, KOH, RbOH, CsOH, and (C2H54N(OH. The electrolyte conductivity is found to be closely related to cation size in the hydroxide compound used as 1 M additive to the 4 M KOH aqueous solution. The degradation performance of Mg52Ni39Co3Mn6 alloy through cycling demonstrates a strong correlation with the redox potential of the cation in the alkali hydroxide compound used as 1 M additive to the 5 M KOH aqueous solution. NaOH, CsOH, and (C2H54N(OH additions are found to achieve a good balance between corrosion and conductivity performances.

  8. Method for recovering metals from waste

    Science.gov (United States)

    Wicks, G.G.; Clark, D.E.; Schulz, R.L.

    1998-12-01

    A method is described for recovering metals from metals-containing wastes, and vitrifying the remainder of the wastes for disposal. Metals-containing wastes such as circuit boards, cathode ray tubes, vacuum tubes, transistors and so forth, are broken up and placed in a suitable container. The container is heated by microwaves to a first temperature in the range of approximately 300--800 C to combust organic materials in the waste, then heated further to a second temperature in the range of approximately 1,000--1,550 C at which temperature glass formers present in the waste will cause it to melt and vitrify. Low-melting-point metals such as tin and aluminum can be recovered after organics combustion is substantially complete. Metals with higher melting points, such as gold, silver and copper, can be recovered from the solidified product or separated from the waste at their respective melting points. Network former-containing materials can be added at the start of the process to assist vitrification. 2 figs.

  9. Recovery of valuable metals from industrial wastes

    Directory of Open Access Journals (Sweden)

    A. K. Serikbayeva

    2013-10-01

    Full Text Available Recovery of valuable metals as osmium and rhenium from a industrial wastes are an actual problem. A wastes of copper production treat slime and cake. The content of rhenium in them makes 600 – 2 000 g/t, osmium to 50 g/t. In article results of research of a form of finding of osmium and rhenium in such waste and influence phase transformation of the main components on their extraction when processing are stated. The probable reactions, proceeding in this system are provided. The way of receiving enriched with osmium and rhenium of concentrates from a waste is offered.

  10. Biohydrometallurgical methods for metals recovery from waste materials

    Directory of Open Access Journals (Sweden)

    J. Willner

    2015-01-01

    Full Text Available The article draws attention to recently conducted research of bacterial leaching of metals from various polymetallic waste. These wastes are the carriers of valuable metals: base metals, precious and platinum group metals (e.g. electronic waste, spent catalysts or rare earth elements.

  11. Vapor phase hydrogenation of furfural over nickel mixed metal oxide catalysts derived from layered double hydroxides

    Energy Technology Data Exchange (ETDEWEB)

    Sulmonetti, Taylor P.; Pang, Simon H.; Claure, Micaela Taborga; Lee, Sungsik; Cullen, David A.; Agrawal, Pradeep K.; Jones, Christopher W.

    2016-05-01

    The hydrogenation of furfural is investigated over various reduced nickel mixed metal oxides derived from layered double hydroxides (LDHs) containing Ni-Mg-Al and Ni-Co-Al. Upon reduction, relatively large Ni(0) domains develop in the Ni-Mg-Al catalysts, whereas in the Ni-Co-Al catalysts smaller metal particles of Ni(0) and Co(0), potentially as alloys, are formed, as evidenced by XAS, XPS, STEM and EELS. All the reduced Ni catalysts display similar selectivities towards major hydrogenation products (furfuryl alcohol and tetrahydrofurfuryl alcohol), though the side products varied with the catalyst composition. The 1.1Ni-0.8Co-Al catalyst showed the greatest activity per titrated site when compared to the other catalysts, with promising activity compared to related catalysts in the literature. The use of base metal catalysts for hydrogenation of furanic compounds may be a promising alternative to the well-studied precious metal catalysts for making biomass-derived chemicals if catalyst selectivity can be improved in future work by alloying or tuning metal-oxide support interactions.

  12. The metal-organic framework MIL-53(Al) constructed from multiple metal sources: alumina, aluminum hydroxide, and boehmite.

    Science.gov (United States)

    Li, Zehua; Wu, Yi-nan; Li, Jie; Zhang, Yiming; Zou, Xin; Li, Fengting

    2015-04-27

    Three aluminum compounds, namely alumina, aluminum hydroxide, and boehmite, are probed as the metal sources for the hydrothermal synthesis of a typical metal-organic framework MIL-53(Al). The process exhibits enhanced synthetic efficiency without the generation of strongly acidic byproducts. The time-course monitoring of conversion from different aluminum sources into MIL-53(Al) is achieved by multiple characterization that reveals a similar but differentiated crystallinity, porosity, and morphology relative to typical MIL-53(Al) prepared from water-soluble aluminum salts. Moreover, the prepared MIL-53(Al) constructed with the three insoluble aluminum sources exhibit an improved thermal stability of up to nearly 600 °C and enhanced yields. Alumina and boehmite are more preferable than aluminum hydroxide in terms of product porosity, yield, and reaction time. The adsorption performances of a typical environmental endocrine disruptor, dimethyl phthalate, on the prepared MIL-53(Al) samples are also investigated. The improved structural stability of MIL-53(Al) prepared from these alternative aluminum sources enables double-enhanced adsorption performance (up to 206 mg g(-1)) relative to the conventionally obtained MIL-53(Al). © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  13. Cobalt Iron Hydroxide as a Precious Metal-Free Bifunctional Electrocatalyst for Efficient Overall Water Splitting.

    Science.gov (United States)

    Babar, Pravin; Lokhande, Abhishek; Shin, Hyeong Ho; Pawar, Bharati; Gang, Myeng Gil; Pawar, Sambhaji; Kim, Jin Hyeok

    2018-02-01

    Highly efficient and stable electrocatalysts from inexpensive and earth-abundant elements are emerging materials in the overall water splitting process. Herein, cobalt iron hydroxide nanosheets are directly deposited on nickel foam by a simple and rapid electrodeposition method. The cobalt iron hydroxide (CoFe/NF) nanosheets not only allow good exposure of the highly active surface area but also facilitate the mass and charge transport capability. As an anode, the CoFe/NF electrocatalyst displays excellent oxygen evolution reaction catalytic activity with an overpotential of 220 mV at a current density of 10 mA cm -2 . As a cathode, it exhibits good performance in the hydrogen evolution reaction with an overpotential of 110 mV, reaching a current density of 10 mA cm -2 . When CoFe/NF electrodes are used as the anode and the cathode for water splitting, a low cell voltage of 1.64 V at 10 mA cm -2 and excellent stability for 50 h are observed. The present work demonstrates a possible pathway to develop a highly active and durable substitute for noble metal electrocatalysts for overall water splitting. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  14. SEPARATION OF PLUTONIUM HYDROXIDE FROM BISMUTH HYDROXIDE

    Science.gov (United States)

    Watt, G.W.

    1958-08-19

    An tmproved method is described for separating plutonium hydroxide from bismuth hydroxide. The end product of the bismuth phosphate processes for the separation amd concentration of plutonium is a inixture of bismuth hydroxide amd plutonium hydroxide. It has been found that these compounds can be advantageously separated by treatment with a reducing agent having a potential sufficient to reduce bismuth hydroxide to metalltc bisinuth but not sufficient to reduce the plutonium present. The resulting mixture of metallic bismuth and plutonium hydroxide can then be separated by treatment with a material which will dissolve plutonium hydroxide but not metallic bismuth. Sodiunn stannite is mentioned as a preferred reducing agent, and dilute nitric acid may be used as the separatory solvent.

  15. Magnesium alloys and graphite wastes encapsulated in cementitious materials: Reduction of galvanic corrosion using alkali hydroxide activated blast furnace slag

    Energy Technology Data Exchange (ETDEWEB)

    Chartier, D., E-mail: david.chartier@cea.fr [Commissariat à l' Energie Atomique et aux Energies Alternatives, CEA, DEN, DTCD, SPDE, F-30207 Bagnols-sur-Cèze (France); Muzeau, B. [DEN-Service d’Etude du Comportement des Radionucléides (SECR), CEA, Université Paris-Saclay, F-91191, Gif-sur-Yvette (France); Stefan, L. [AREVA NC/D& S - France/Technical Department, 1 place Jean Millier 92084 Paris La Défense (France); Sanchez-Canet, J. [Commissariat à l' Energie Atomique et aux Energies Alternatives, CEA, DEN, DTCD, SPDE, F-30207 Bagnols-sur-Cèze (France); Monguillon, C. [DEN-Service d’Etude du Comportement des Radionucléides (SECR), CEA, Université Paris-Saclay, F-91191, Gif-sur-Yvette (France)

    2017-03-15

    Highlights: • Embedded in cement, magnesium is corroded by residual water present in porosity of the matrix. • Corrosion is enhanced by galvanic phenomenon when magnesium is in contact with graphite. • Galvanic corrosion of magnesium in contact with graphite debris is shown to be severe with ordinary Portland cement. • Galvanic corrosion is significantly lowered in high alkali medium such as sodium hydroxide. • Sodium hydroxide activated blast furnace slag is a convenient binder to embed magnesium. - Abstract: Magnesium alloys and graphite from spent nuclear fuel have been stored together in La Hague plant. The packaging of these wastes is under consideration. These wastes could be mixed in a grout composed of industrially available cement (Portland, calcium aluminate…). Within the alkaline pore solution of these matrixes, magnesium alloys are imperfectly protected by a layer of Brucite resulting in a slow corrosion releasing hydrogen. As the production of this gas must be considered for the storage safety, and the quality of wasteform, it is important to select a cement matrix capable of lowering the corrosion kinetics. Many types of calcium based cements have been tested and most of them have caused strong hydrogen production when magnesium alloys and graphite are conditioned together because of galvanic corrosion. Exceptions are binders based on alkali hydroxide activated ground granulated blast furnace slag (BFS) which are presented in this article.

  16. Oxidatively Electrodeposited Thin-Film Transition Metal (Oxy)hydroxides as Oxygen Evolution Catalysts.

    Science.gov (United States)

    Morales-Guio, Carlos G; Liardet, Laurent; Hu, Xile

    2016-07-20

    The electrolysis of water to produce hydrogen and oxygen is a simple and attractive approach to store renewable energies in the form of chemical fuels. The oxygen evolution reaction (OER) is a complex four-electron process that constitutes the most energy-inefficient step in water electrolysis. Here we describe a novel electrochemical method for the deposition of a family of thin-film transition metal (oxy)hydroxides as OER catalysts. The thin films have nanodomains of crystallinity with lattice spacing similar to those of double-layered hydroxides. The loadings of these thin-film catalysts were accurately determined with a resolution of below 1 μg cm(-2) using an electrochemical quartz microcrystal balance. The loading-activity relations for various catalysts were established using voltammetry and impedance spectroscopy. The thin-film catalysts have up to four types of loading-activity dependence due to film nucleation and growth as well as the resistance of the films. A zone of intrinsic activity has been identified for all of the catalysts where the mass-averaged activity remains constant while the loading is increased. According to their intrinsic activities, the metal oxides can be classified into three categories: NiOx, MnOx, and FeOx belong to category I, which is the least active; CoOx and CoNiOx belong to category II, which has medium activity; and FeNiOx, CoFeOx, and CoFeNiOx belong to category III, which is the most active. The high turnover frequencies of CoFeOx and CoFeNiOx at low overpotentials and the simple deposition method allow the fabrication of high-performance anode electrodes coated with these catalysts. In 1 M KOH and with the most active electrode, overpotentials as low as 240 and 270 mV are required to reach 10 and 100 mA cm(-2), respectively.

  17. Transition metal ions regulated oxygen evolution reaction performance of Ni-based hydroxides hierarchical nanoarrays

    Science.gov (United States)

    Zhou, Tingting; Cao, Zhen; Zhang, Pan; Ma, Houyi; Gao, Zhen; Wang, Heng; Lu, Yue; He, Jia; Zhao, Yunfeng

    2017-04-01

    Nickel-based hydroxide hierarchical nanoarrays (NiyM(OH)x HNAs M = Fe or Zn) are doped with non-noble transition metals to create nanostructures and regulate their activities for the oxygen evolution reaction. Catalytic performance in these materials depends on their chemical composition and the presence of nanostructures. These novel hierarchical nanostructures contain small secondary nanosheets that are grown on the primary nanowire arrays, providing a higher surface area and more efficient mass transport for electrochemical reactions. The activities of the NiyM(OH)x HNAs for the oxygen evolution reaction (OER) followed the order of Ni2.2Fe(OH)x > Ni(OH)2 > Ni2.1Zn(OH)x, and these trends are supported by density functional theory (DFT) calculations. The Fe-doped nickel hydroxide hierarchical nanoarrays (Ni2.2Fe(OH)x HNAs), which had an appropriate elemental composition and hierarchical nanostructures, achieve the lowest onset overpotential of 234 mV and the smallest Tafel slope of 64.3 mV dec-1. The specific activity, which is normalized to the Brunauer-Emmett-Teller (BET) surface area of the catalyst, of the Ni2.2Fe(OH)x HNAs is 1.15 mA cm-2BET at an overpotential of 350 mV. This is ~4-times higher than that of Ni(OH)2. These values are also superior to those of a commercial IrOx electrocatalyst.

  18. The Role of Hydroxide and Metal Concentration on the Viscoelastic Properties of Metal Coordinated Gels

    Science.gov (United States)

    Cazzell, Seth; Holten-Andersen, Niels

    Nature uses metal binding amino acids to engineer mechanical properties. An example of this engineering can be found in the mussel byssal thread. This acellular thread contains reversible intermolecular protein-metal bonds, which allows the mussel to robustly anchor to rocks, while withstanding the mechanically demanding intertidal environment. Inspired by this metal-binding material, we present a synthetic hydrogel designed to mimic this bonding behavior. The mechanical properties of this hydrogel can be controlled independently by manipulating the amount of metal relative to the metal binding ligand, and the gel's pH. Here we report how high metal to ligand ratios and low pH can be used to induce the formation of a strong, slow relaxing gels. This gel has potential applications as an energy dissipating material, and furthers our understanding of the bio-inspired engineering techniques that are used to design viscoelastic soft materials. I was supported by the Department of Defense (DoD) through the National Defense Science & Engineering Graduate Fellowship (NDSEG) Program.

  19. Application of magnesium hydroxide and barium hydroxide for the ...

    African Journals Online (AJOL)

    Application of magnesium hydroxide and barium hydroxide for the removal of metals and sulphate from mine water. ... equivalent to the Ba(OH)2 dosage. During CO2-dosing, CaCO3 is precipitated to the saturation level of CaCO3. Keywords: Magnesium hydroxide; barium hydroxide; sulphate removal; water treatment ...

  20. Magnesium alloys and graphite wastes encapsulated in cementitious materials: Reduction of galvanic corrosion using alkali hydroxide activated blast furnace slag.

    Science.gov (United States)

    Chartier, D; Muzeau, B; Stefan, L; Sanchez-Canet, J; Monguillon, C

    2017-03-15

    Magnesium alloys and graphite from spent nuclear fuel have been stored together in La Hague plant. The packaging of these wastes is under consideration. These wastes could be mixed in a grout composed of industrially available cement (Portland, calcium aluminate…). Within the alkaline pore solution of these matrixes, magnesium alloys are imperfectly protected by a layer of Brucite resulting in a slow corrosion releasing hydrogen. As the production of this gas must be considered for the storage safety, and the quality of wasteform, it is important to select a cement matrix capable of lowering the corrosion kinetics. Many types of calcium based cements have been tested and most of them have caused strong hydrogen production when magnesium alloys and graphite are conditioned together because of galvanic corrosion. Exceptions are binders based on alkali hydroxide activated ground granulated blast furnace slag (BFS) which are presented in this article. Copyright © 2016 Elsevier B.V. All rights reserved.

  1. Activity targets for nanostructured platinum-group-metal-free catalysts in hydroxide exchange membrane fuel cells

    Science.gov (United States)

    Setzler, Brian P.; Zhuang, Zhongbin; Wittkopf, Jarrid A.; Yan, Yushan

    2016-12-01

    Fuel cells are the zero-emission automotive power source that best preserves the advantages of gasoline automobiles: low upfront cost, long driving range and fast refuelling. To make fuel-cell cars a reality, the US Department of Energy has set a fuel cell system cost target of US$30 kW-1 in the long-term, which equates to US$2,400 per vehicle, excluding several major powertrain components (in comparison, a basic, but complete, internal combustion engine system costs approximately US$3,000). To date, most research for automotive applications has focused on proton exchange membrane fuel cells (PEMFCs), because these systems have demonstrated the highest power density. Recently, however, an alternative technology, hydroxide exchange membrane fuel cells (HEMFCs), has gained significant attention, because of the possibility to use stable platinum-group-metal-free catalysts, with inherent, long-term cost advantages. In this Perspective, we discuss the cost profile of PEMFCs and the advantages offered by HEMFCs. In particular, we discuss catalyst development needs for HEMFCs and set catalyst activity targets to achieve performance parity with state-of-the-art automotive PEMFCs. Meeting these targets requires careful optimization of nanostructures to pack high surface areas into a small volume, while maintaining high area-specific activity and favourable pore-transport properties.

  2. Manipulating the Architecture of Atomically Thin Transition Metal (Hydr)oxides for Enhanced Oxygen Evolution Catalysis.

    Science.gov (United States)

    Dou, Yuhai; Zhang, Lei; Xu, Jiantie; He, Chun-Ting; Xu, Xun; Sun, Ziqi; Liao, Ting; Nagy, Balázs; Liu, Porun; Dou, Shi Xue

    2018-02-27

    Graphene-like nanomaterials have received tremendous research interest due to their atomic thickness and fascinating properties. Previous studies mainly focus on the modulation of their electronic structures, which undoubtedly optimizes the electronic properties, but is not the only determinant of performance in practical applications. Herein, we propose a generalized strategy to incrementally manipulate the architectures of several atomically thin transition metal (hydr)oxides, and study their effects on catalytic water oxidation. The results demonstrate the obvious superiority of a wrinkled nanosheet architecture in both catalytic activity and durability. For instance, wrinkled Ni(OH) 2 nanosheets display a low overpotential of 358.2 mV at 10 mA cm -2 , a high current density of 187.2 mA cm -2 at 500 mV, a small Tafel slope of 54.4 mV dec -1 , and excellent long-term durability with gradually optimized performance, significantly outperforming other nanosheet architectures and previously reported catalysts. The outstanding catalytic performance is mainly attributable to the 3D porous network structure constructed by wrinkled nanosheets, which not only provides sufficient contact between electrode materials and current collector, but also offers highly accessible channels for facile electrolyte diffusion and efficient O 2 escape. Our study provides a perspective on improving the performance of graphene-like nanomaterials in a wide range of practical applications.

  3. Activity targets for nanostructured platinum-group-metal-free catalysts in hydroxide exchange membrane fuel cells.

    Science.gov (United States)

    Setzler, Brian P; Zhuang, Zhongbin; Wittkopf, Jarrid A; Yan, Yushan

    2016-12-06

    Fuel cells are the zero-emission automotive power source that best preserves the advantages of gasoline automobiles: low upfront cost, long driving range and fast refuelling. To make fuel-cell cars a reality, the US Department of Energy has set a fuel cell system cost target of US$30 kW(-1) in the long-term, which equates to US$2,400 per vehicle, excluding several major powertrain components (in comparison, a basic, but complete, internal combustion engine system costs approximately US$3,000). To date, most research for automotive applications has focused on proton exchange membrane fuel cells (PEMFCs), because these systems have demonstrated the highest power density. Recently, however, an alternative technology, hydroxide exchange membrane fuel cells (HEMFCs), has gained significant attention, because of the possibility to use stable platinum-group-metal-free catalysts, with inherent, long-term cost advantages. In this Perspective, we discuss the cost profile of PEMFCs and the advantages offered by HEMFCs. In particular, we discuss catalyst development needs for HEMFCs and set catalyst activity targets to achieve performance parity with state-of-the-art automotive PEMFCs. Meeting these targets requires careful optimization of nanostructures to pack high surface areas into a small volume, while maintaining high area-specific activity and favourable pore-transport properties.

  4. Toxic metal levels in Nigerian electronic waste workers indicate ...

    African Journals Online (AJOL)

    These data indicate that the elevated body burden of toxic metals in the e-waste exposed population is an indication of occupational metal toxicity associated with crude e-waste management practices in Nigeria. In addition, the potential health implications of exposure to these toxic metals, such as chronic kidney disease, ...

  5. Electrochemical corrosion testing of metal waste forms

    Energy Technology Data Exchange (ETDEWEB)

    Abraham, D. P.; Peterson, J. J.; Katyal, H. K.; Keiser, D. D.; Hilton, B. A.

    1999-12-14

    Electrochemical corrosion tests have been conducted on simulated stainless steel-zirconium (SS-Zr) metal waste form (MWF) samples. The uniform aqueous corrosion behavior of the samples in various test solutions was measured by the polarization resistance technique. The data show that the MWF corrosion rates are very low in groundwaters representative of the proposed Yucca Mountain repository. Galvanic corrosion measurements were also conducted on MWF samples that were coupled to an alloy that has been proposed for the inner lining of the high-level nuclear waste container. The experiments show that the steady-state galvanic corrosion currents are small. Galvanic corrosion will, hence, not be an important mechanism of radionuclide release from the MWF alloys.

  6. Aluminum Hydroxide and Magnesium Hydroxide

    Science.gov (United States)

    Aluminum Hydroxide, Magnesium Hydroxide are antacids used together to relieve heartburn, acid indigestion, and upset stomach. They ... They combine with stomach acid and neutralize it. Aluminum Hydroxide, Magnesium Hydroxide are available without a prescription. ...

  7. 40 CFR 268.34 - Waste specific prohibitions-toxicity characteristic metal wastes.

    Science.gov (United States)

    2010-07-01

    ... characteristic metal wastes. 268.34 Section 268.34 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... specific prohibitions—toxicity characteristic metal wastes. (a) Effective August 24, 1998, the following... Toxic Characteristic Leaching Procedure but not the Extraction Procedure), and waste, soil, or debris...

  8. INNOVATIVE PRACTICES FOR TREATING WASTE STREAMS CONTAINING HEAVY METALS: A WASTE MINIMIZATION APPROACH

    Science.gov (United States)

    Innovative practices for treating waste streams containing heavy metals often involve technologies or systems that either reduce the amount of waste generated or recover reusable resources. With the land disposal of metal treatment residuals becoming less of an accepted waste man...

  9. Accumulation of heavy metals by vegetables grown in mine wastes

    Energy Technology Data Exchange (ETDEWEB)

    Cobb, G.P.; Sands, K.; Waters, M.; Wixson, B.G.; Dorward-King, E.

    2000-03-01

    Lead, cadmium, arsenic, and zinc were quantified in mine wastes and in soils mixed with mine wastes. Metal concentrations were found to be heterogeneous in the wastes. Iceberg lettuce, Cherry Belle radishes, Roma bush beans, and Better Boy tomatoes were cultivated in mine wastes and in waste-amended soils. Lettuce and radishes had 100% survival in the 100% mine waste treatments compared to 0% and 25% survival for tomatoes and beans, respectively. Metal concentrations were determined in plant tissues to determine uptake and distribution of metals in the edible plant parts. Individual soil samples were collected beneath each plant to assess metal content in the immediate plant environment. This analysis verified heterogeneous metal content of the mine wastes. The four plant species effectively accumulated and translocated lead, cadmium, arsenic, and zinc. Tomato and bean plants contained the four metals mainly in the roots and little was translocated to the fruits. Radish roots accumulated less metals compared to the leaves, whereas lettuce roots and leaves accumulated similar concentrations of the four metals. Lettuce leaves and radish roots accumulated significantly more metals than bean and tomato fruits. This accumulation pattern suggests that consumption of lettuce leaves or radish roots from plants grown in mine wastes would pose greater risks to humans and wildlife than would consumption of beans or tomatoes grown in the same area. The potential risk may be mitigated somewhat in humans, as vegetables grown in mine wastes exhibited stunted growth and chlorosis.

  10. Layered Double Hydroxides as Effective Adsorbents for U(VI and Toxic Heavy Metals Removal from Aqueous Media

    Directory of Open Access Journals (Sweden)

    G. N. Pshinko

    2013-01-01

    Full Text Available Capacities of different synthesized Zn,Al-hydrotalcite-like adsorbents, including the initial carbonate [Zn4Al2(OH12]·CO3·8H2O and its forms intercalated with chelating agents (ethylenediaminetetraacetic acid (EDTA, diethylenetriaminepentaacetic acid (DTPA, and hexamethylenediaminetetraacetic acid (HMDTA and heat-treated form Zn4Al2O7, to adsorb uranium(VI and ions of toxic heavy metals have been compared. Metal sorption capacities of hydrotalcite-like adsorbents have been shown to correlate with the stability of their complexes with the mentioned chelating agents in a solution. The synthesized layered double hydroxides (LDHs containing chelating agents in the interlayer space are rather efficient for sorption purification of aqueous media free from U(VI irrespective of its forms of natural abundance (including water-soluble bi- and tricarbonate forms and from heavy metal ions. [Zn4Al2(OH12]·EDTA·nH2O is recommended for practical application as one of the most efficient and inexpensive synthetic adsorbents designed for recovery of both cationic and particularly important anionic forms of U(VI and other heavy metals from aqueous media. Carbonate forms of LDHs turned out to be most efficient for recovery of Cu(II from aqueous media with pH0≥7 owing to precipitation of Cu(II basic carbonates and Cu(II hydroxides. Chromate ions are efficiently adsorbed from water only by calcinated forms of LDHs.

  11. Attenuation of heavy metal leaching from hazardous wastes by co-disposal of wastes

    Energy Technology Data Exchange (ETDEWEB)

    Bae, Wookeun; Shin, Eung Bai [Hanyang Univ., Ansan (Korea, Republic of); Lee, Kil Chul; Kim, Jae Hyung [National Institute of Environmental Research, Seoul (Korea, Republic of)] [and others

    1996-12-31

    The potential hazard of landfill wastes was previously evaluated by examining the extraction procedures for individual waste, although various wastes were co-disposed of in actual landfills. This paper investigates the reduction of extraction-procedure toxicity by co-disposing various combinations of two wastes. When two wastes are mixed homogeneously, the extraction of heavy metals from the waste mixture is critically affected by the extract pH. Thus, co-disposal wastes will have a resultant pH between the pH values of its constituent. The lower the resultant pH, the lower the concentrations of heavy metals in the extract. When these wastes are extracted sequentially, the latter extracted waste has a stronger influence on the final concentration of heavy metals in the extract. Small-scale lysimeter experiments confirm that when heavy-metal-bearing leachates Generated from hazardous-waste lysimeters are passed through a nonhazardous-waste lysimeter filled with compost, briquette ash, or refuse-incineration ashes, the heavy-metal concentration in the final leachates decreases significantly. Thus, the heavy-metal leaching could be attenuated if a less extraction-procedure-toxic waste were placed at the bottom of a landfill. 3 refs., 4 figs., 5 tabs.

  12. Metallurgical recovery of metals from electronic waste: a review.

    Science.gov (United States)

    Cui, Jirang; Zhang, Lifeng

    2008-10-30

    Waste electric and electronic equipment, or electronic waste, has been taken into consideration not only by the government but also by the public due to their hazardous material contents. In the detailed literature survey, value distributions for different electronic waste samples were calculated. It is showed that the major economic driver for recycling of electronic waste is from the recovery of precious metals. The state of the art in recovery of precious metals from electronic waste by pyrometallurgical processing, hydrometallurgical processing, and biometallurgical processing are highlighted in the paper. Pyrometallurgical processing has been a traditional technology for recovery of precious metals from waste electronic equipment. However, state-of-the-art smelters are highly depended on investments. Recent research on recovery of energy from PC waste gives an example for using plastics in this waste stream. It indicates that thermal processing provides a feasible approach for recovery of energy from electronic waste if a comprehensive emission control system is installed. In the last decade, attentions have been removed from pyrometallurgical process to hydrometallurgical process for recovery of metals from electronic waste. In the paper, hydrometallurgical processing techniques including cyanide leaching, halide leaching, thiourea leaching, and thiosulfate leaching of precious metals are detailed. In order to develop an environmentally friendly technique for recovery of precious metals from electronic scrap, a critical comparison of main leaching methods is analyzed for both economic feasibility and environmental impact. It is believed that biotechnology has been one of the most promising technologies in metallurgical processing. Bioleaching has been used for recovery of precious metals and copper from ores for many years. However, limited research was carried out on the bioleaching of metals from electronic waste. In the review, initial researches on the

  13. Concentration of precious metals during their recovery from electronic waste.

    Science.gov (United States)

    Cayumil, R; Khanna, R; Rajarao, R; Mukherjee, P S; Sahajwalla, V

    2016-11-01

    The rapid growth of electronic devices, their subsequent obsolescence and disposal has resulted in electronic waste (e-waste) being one of the fastest increasing waste streams worldwide. The main component of e-waste is printed circuit boards (PCBs), which contain substantial quantities of precious metals in concentrations significantly higher than those typically found in corresponding ores. The high value and limited reserves of minerals containing these metals makes urban mining of precious metals very attractive. This article is focused on the concentration and recovery of precious metals during pyro-metallurgical recycling of waste PCBs. High temperature pyrolysis was carried out for ten minutes in a horizontal tube furnace in the temperature range 800-1350°C under Argon gas flowing at 1L/min. These temperatures were chosen to lie below and above the melting point (1084.87°C) of copper, the main metal in PCBs, to study the influence of its physical state on the recovery of precious metals. The heat treatment of waste PCBs resulted in two different types of solid products, namely a carbonaceous non-metallic fraction (NMFs) and metallic products, composed of copper rich foils and/or droplets and tin-lead rich droplets and some wires. Significant proportions of Ag, Au, Pd and Pt were found concentrated within two types of metallic phases, with very limited quantities retained by the NMFs. This process was successful in concentrating several precious metals such as Ag, Au, Pd and Pt in a small volume fraction, and reduced volumes for further processing/refinement by up to 75%. The amounts of secondary wastes produced were also minimised to a great extent. The generation of precious metals rich metallic phases demonstrates high temperature pyrolysis as a viable approach towards the recovery of precious metals from e-waste. Copyright © 2015 Elsevier Ltd. All rights reserved.

  14. Methods for recovering metals from electronic waste, and related systems

    Science.gov (United States)

    Lister, Tedd E; Parkman, Jacob A; Diaz Aldana, Luis A; Clark, Gemma; Dufek, Eric J; Keller, Philip

    2017-10-03

    A method of recovering metals from electronic waste comprises providing a powder comprising electronic waste in at least a first reactor and a second reactor and providing an electrolyte comprising at least ferric ions in an electrochemical cell in fluid communication with the first reactor and the second reactor. The method further includes contacting the powders within the first reactor and the second reactor with the electrolyte to dissolve at least one base metal from each reactor into the electrolyte and reduce at least some of the ferric ions to ferrous ions. The ferrous ions are oxidized at an anode of the electrochemical cell to regenerate the ferric ions. The powder within the second reactor comprises a higher weight percent of the at least one base metal than the powder in the first reactor. Additional methods of recovering metals from electronic waste are also described, as well as an apparatus of recovering metals from electronic waste.

  15. Production of calcium hydroxide from the waste of Cariri stone; Producao de hidroxido de calcio a partir de residuo da pedra Cariri

    Energy Technology Data Exchange (ETDEWEB)

    Alves, T.M.E.; Santos, A.M.M.; Brasileiro, M.I.; Pinheiro, S.F.L.; Prado, A.C.A., E-mail: tiagomaiaea@gmail.com [Universidade Federal do Cariri (UFCA), Juazeiro do Norte, CE (Brazil)

    2016-07-01

    The extraction of Cariri stone in the northeast is a frequent activity because of its ornamental application as well as for the construction sector. However, by this extraction, untapped waste formation grows and becomes a problem for the environment. The objective of this work is to produce calcium hydroxide, from this limestone residue, with controlled porosity, solubility and particle size. The waste was characterized with X-Ray Diffraction (XRD), X-Ray Fluorescence (XRF) and thermal analysis (TGA). The limestone was calcined at 850°C and 950°C for 45 minutes and three hours, being characterized by XRD, XRF and TGA. Once calcined, it was hydrated with 17,5g and 22g oxide to 100mL water and manually mixed for 15 and 25 minutes. The calcium hydroxides have been submitted for tests in vivo in rats and will be characterized by XRD, Scanning Electron Microscopy (SEM) and Infrared. (author)

  16. Fate of metals contained in waste electrical and electronic equipment in a municipal waste treatment process.

    Science.gov (United States)

    Oguchi, Masahiro; Sakanakura, Hirofumi; Terazono, Atsushi; Takigami, Hidetaka

    2012-01-01

    In Japan, waste electrical and electronic equipment (WEEE) that is not covered by the recycling laws are treated as municipal solid waste. A part of common metals are recovered during the treatment; however, other metals are rarely recovered and their destinations are not clear. This study investigated the distribution ratios and substance flows of 55 metals contained in WEEE during municipal waste treatment using shredding and separation techniques at a Japanese municipal waste treatment plant. The results revealed that more than half of Cu and most of Al contained in WEEE end up in landfills or dissipate under the current municipal waste treatment system. Among the other metals contained in WEEE, at least 70% of the mass was distributed to the small-grain fraction through the shredding and separation and is to be landfilled. Most kinds of metals were concentrated several fold in the small-grain fraction through the process and therefore the small-grain fraction may be a next target for recovery of metals in terms of both metal content and amount. Separate collection and pre-sorting of small digital products can work as effective way for reducing precious metals and less common metals to be landfilled to some extent; however, much of the total masses of those metals would still end up in landfills and it is also important to consider how to recover and utilize metals contained in other WEEE such as audio/video equipment. Copyright © 2011 Elsevier Ltd. All rights reserved.

  17. Fe(III) hydroxide nucleation and growth on quartz in the presence of Cu(II), Pb(II), and Cr(III): metal hydrolysis and adsorption.

    Science.gov (United States)

    Dai, Chong; Hu, Yandi

    2015-01-06

    Fe(III) hydroxide nanoparticles are an essential carrier for aqueous heavy metals. Particularly, iron hydroxide precipitation on mineral surfaces can immobilize aqueous heavy metals. Here, we used grazing-incidence small-angle X-ray scattering (GISAXS) to quantify nucleation and growth of iron hydroxide on quartz in 0.1 mM Fe(NO3)3 solution in the presence of Na(+), Cu(2+), Pb(2+), or Cr(3+) at pH = 3.7 ± 0.1. In 30 min, the average radii of gyration (R(g)) of particles on quartz grew from around 2 to 6 nm in the presence of Na(+) and Cu(2+). Interestingly, the particle sizes remained 3.3 ± 0.3 nm in the presence of Pb(2+), and few particles formed in the presence of Cr(3+). Quartz crystal microbalance dissipation (QCM-D) measurements showed that only Cr(3+) adsorbed onto quartz, while Cu(2+) and Pb(2+) did not. Cr(3+) adsorption changed the surface charge of quartz from negative to positive, thus inhibiting the precipitation of positively charged iron hydroxide on quartz. Masses and compositions of the precipitates were also quantified. This study provided new insights on interactions among quartz, iron hydroxide, and metal ions. Such information is helpful not only for environmental remediation but also for the doping design of iron oxide catalysts.

  18. Adsorption of heavy metals by agroforestry waste derived activated ...

    African Journals Online (AJOL)

    Adsorption of heavy metals by agroforestry waste derived activated carbons applied to aqueous solutions. Jane M Misihairabgwi, Abisha Kasiyamhuru, Peter Anderson, Colin J Cunningham, Tanya A Peshkur, Ignatious Ncube ...

  19. Variable charge and electrical double layer of mineral-water interfaces: silver halides versus metal (hydr)oxides.

    Science.gov (United States)

    Hiemstra, Tjisse

    2012-11-06

    Classically, silver (Ag) halides have been used to understand thermodynamic principles of the charging process and the corresponding development of the electrical double layer (EDL). A mechanistic approach to the processes on the molecular level has not yet been carried out using advanced surface complexation modeling (SCM) as applied to metal (hydr)oxide interfaces. Ag halides and metal (hydr)oxides behave quite differently in some respect. The location of charge in the interface of Ag halides is not a priori obvious. For AgI(s), SCM indicates the separation of interfacial charge in which the smaller silver ions are apparently farther away from the surface than iodide. This charge separation can be understood from the surface structure of the relevant crystal faces. Charge separation with positive charge above the surface is due to monodentate surface complex formation of Ag(+) ions binding to I sites located at the surface. Negative surface charge is due to the desorption of Ag(+) ions out of the lattice. These processes can be described with the charge distribution (CD) model. The MO/DFT optimized geometry of the complex is used to estimate the value of the CD. SCM reveals the EDL structure of AgI(s), having two Stern layers in series. The inner Stern layer has a very low capacitance (C(1) = 0.15 ± 0.01 F/m(2)) in comparison to that of metal (hydr)oxides, and this can be attributed to the strong orientation of the (primary) water molecules on the local electrostatic field of the Ag(+) and I(-) ions of the surface (relative dielectric constant ε(r) ≈ 6). Depending on the extent of water ordering, mineral surfaces may in principle develop a second Stern layer. The corresponding capacitance (C(2)) will depend on the degree of water ordering that may decrease in the series AgI (C(2) = 0.57 F/m(2)), goethite (C(2) = 0.74 F/m(2)), and rutile (C(2) = ∞), as discussed. The charging principles of AgI minerals iodargyrite and miersite may also be applied to minerals

  20. Fulvic acid anchored layered double hydroxides: A multifunctional composite adsorbent for the removal of anionic dye and toxic metal.

    Science.gov (United States)

    Li, Lei; Qi, Guangxia; Wang, Bangda; Yue, Dongbei; Wang, Yi; Sato, Tsutomu

    2018-02-05

    A novel multifunctional composite adsorbent which possesses the ability for anion exchange and toxic metal complexation has been synthesized by the hybridization of layered double hydroxides (LDH) and fulvic acid (FA) in this study. The results show that FA with lots of functional groups can be effectively and stably anchored on the surface of LDH through coagulation process without occupying the interlayer of LDH. Therefore, the anion exchange ability remains and the adsorption capacity of Orange II can reach 1.9mmol/g, which is almost as much as stoichiometric anion exchange capacity of pure LDH. Moreover, the composite adsorbent's adsorption capacity of Cu 2+ , Pb 2+ , Ni 2+ and Cd 2+ can also get to 2.25mmol/g, 0.98mmol/g, 0.99mmol/g and 0.16mmol/g respectively with an adsorption preference order of Cu 2+ >Pb 2+ >Ni 2+ >Cd 2+ . In addition, Orange II and toxic metals are able to be simultaneously removed by this composite adsorbent, and the adsorption of toxic metals can be enhanced by the synergetic adsorption of Orange II. Anion exchange with Cl - in LDH matrix accounts for the adsorption of Orange II, while the adsorption of toxic metal is mainly attributed to the complexation of carboxyl functional group derived from FA. Copyright © 2017 Elsevier B.V. All rights reserved.

  1. PASSIVATION LAYER STABILITY OF A METALLIC ALLOY WASTE FORM

    Energy Technology Data Exchange (ETDEWEB)

    Williamson, M.; Mickalonis, J.; Fisher, D.; Sindelar, R.

    2010-08-16

    Alloy waste form development under the Waste Forms Campaign of the DOE-NE Fuel Cycle Research & Development program includes the process development and characterization of an alloy system to incorporate metal species from the waste streams generated during nuclear fuel recycling. This report describes the tests and results from the FY10 activities to further investigate an Fe-based waste form that uses 300-series stainless steel as the base alloy in an induction furnace melt process to incorporate the waste species from a closed nuclear fuel recycle separations scheme. This report is focused on the initial activities to investigate the formation of oxyhydroxide layer(s) that would be expected to develop on the Fe-based waste form as it corrodes under aqueous repository conditions. Corrosion tests were used to evaluate the stability of the layer(s) that can act as a passivation layer against further corrosion and would affect waste form durability in a disposal environment.

  2. A new coprecipitation methodology with lutetium hydroxide for preconcentration of heavy metal ions in herbal plant samples.

    Science.gov (United States)

    Soylak, Mustafa; Murat, Ipek

    2014-01-01

    A new coprecipitation methodology that used lutetium hydroxide as a precipitant for Cu(II), Pb(II), Mn(II), Co(II), Cd(II), Fe(III), and Ni(II) ions in herbal plant and water samples for analysis by atomic absorption spectrometry has been investigated. The parameters such as pH, amount of lutetium, and volume of aqueous sample were optimized for the recovery of these seven metals. The effects of concomitant ions on the separation-preconcentration of analytes were also checked. The validation of the procedure was checked with addition recovery tests and analysis of Standard Reference Material 1570a-Trace Elements in Spinach Leaves and TMDA-70 fortified lake water Certified Reference Material. The LODs for analyte ions were in the range of 1.7-7.2 microg/L. The application of the present procedure was successfully performed for the analysis of analyte contents of herbal plant samples from Turkey.

  3. A bioseparation process for removing heavy metals from waste ...

    African Journals Online (AJOL)

    A bioseparation process for removing heavy metals from waste water using biosorbents. ... The presence of heavy metals in the environment is of major concern because of their toxicity, bioaccumulating tendency, and threat to human life and the environment. In recent years, many low cost sorbents such as algae, fungi ...

  4. Potential groundwater pollution from improper oil and metal waste ...

    African Journals Online (AJOL)

    Suame is an industrialized hub in Kumasi, Ghana, that is noted for vehicle repairs and servicing, sale of automobile spare parts, and metal fabrication. Some of these activities generate huge volumes of waste oil and metals that are often disposed off indiscriminately into the environment. These could pose a threat to the ...

  5. Aluminum Hydroxide

    Science.gov (United States)

    Aluminum hydroxide is used for the relief of heartburn, sour stomach, and peptic ulcer pain and to ... Aluminum hydroxide comes as a capsule, a tablet, and an oral liquid and suspension. The dose and ...

  6. Magnesium Hydroxide

    Science.gov (United States)

    Magnesium hydroxide is used on a short-term basis to treat constipation.This medication is sometimes prescribed for ... Magnesium hydroxide come as a tablet and liquid to take by mouth. It usually is taken as needed ...

  7. CLASSIFICATION AND PROPORTIES OF DISPERSED METAL WASTES

    Directory of Open Access Journals (Sweden)

    S. L. Rovin

    2015-01-01

    Full Text Available Has been classified and investigated the composition and properties of particulate iron-containing waste and the possibility of their processing and return to the industry. Describes the capabilities and prospects of recycling of particulate wastes in tilting rotary furnaces (TRF without preprocessing

  8. Determination of some heavy metals by flame atomic absorption spectrometry before coprecipitation with neodymium hydroxide.

    Science.gov (United States)

    Soylak, Mustafa; Kizil, Nebiye

    2011-01-01

    A procedure is described for the determination of trace amounts of Cd(II), Ni(II), Cu(II), Pb(II), Fe(III), Co(II), and Mn(II) that combines flame atomic absorption spectrometry with neodymium hydroxide coprecipitation. The influences of analytical parameters (amount of neodymium, pH of the model solutions, etc.) that affect quantitative recoveries of the analyte ions were investigated. The effects of concomitant ions were also examined. The detection limits for analytes were found in the range of 0.2-3.3 microg/L. The validation of the presented procedure was controlled by analysis of certified reference materials (National Institute of Standards and Technology 1570a spinach leaves and TMDA 54.4 fortified lake water). The applications of the procedure were performed by the analysis of water, food, and herbal plants from Turkey.

  9. Cellular Fe-hydroxides and heavy metal sorption in Euglena sp. (algae): implications for biomineralization

    Energy Technology Data Exchange (ETDEWEB)

    Mann, H.; Beveridge, T.O. Fyfe, W.S.; Tazaki, K.

    1985-01-01

    STEM imagery and electron diffraction patterns of Euglena sp. reveal pronounced intra and cellular-membrane aggregates of Fe-hydroxides (some lepidocrocite), in natural communities from tailings waters, Elliott Lake, Ontario. Pure isolates of Euglena sp. contain 40-70% Fe by dry weight and in addition average Al 28,000 ppm, Sr 150, Ba 40, Zn 150, Mn 250, Ni 120, Pb 1600, Th 70, Cu 200 and U 180. In tailings waters, Fe solute concentrations average 560 ppm and U 50 ppb. Concentration factors for Fe, Ba, Zn, Mn, Ti, V, Ni, Pb, Cr, Ag, Co and Cu in algae referenced to average world river waters are greater than or equal to 10/sup 6/. These results endorse the premise that microorganisms mediate transfer of many solutes between the hydrosphere and sedimentary regime.

  10. Methods for recovering precious metals from industrial waste

    Science.gov (United States)

    Canda, L.; Heput, T.; Ardelean, E.

    2016-02-01

    The accelerated rate of industrialization increases the demand for precious metals, while high quality natural resources are diminished quantitatively, with significant operating costs. Precious metals recovery can be successfully made from waste, considered to be secondary sources of raw material. In recent years, concerns and interest of researchers for more increasing efficient methods to recover these metals, taking into account the more severe environmental protection legislation. Precious metals are used in a wide range of applications, both in electronic and communications equipment, spacecraft and jet aircraft engines and for mobile phones or catalytic converters. The most commonly recovered precious metals are: gold from jewellery and electronics, silver from X- ray films and photographic emulsions, industrial applications (catalysts, batteries, glass/mirrors), jewellery; platinum group metals from catalytic converters, catalysts for the refining of crude oil, industrial catalysts, nitric acid manufacturing plant, the carbon-based catalyst, e-waste. An important aspect is the economic viability of recycling processes related to complex waste flows. Hydrometallurgical and pyrometallurgical routes are the most important ways of processing electrical and electronic equipment waste. The necessity of recovering precious metals has opened new opportunities for future research.

  11. Thermal and hydrometallurgical recovery methods of heavy metals from municipal solid waste fly ash

    Energy Technology Data Exchange (ETDEWEB)

    Kuboňová, L., E-mail: lenka.kubonova@vsb.cz [VSB – Technical University of Ostrava, 17. listopadu 15/2172, 708 33 Ostrava (Czech Republic); Langová, Š. [VSB – Technical University of Ostrava, 17. listopadu 15/2172, 708 33 Ostrava (Czech Republic); Nowak, B.; Winter, F. [Institute of Chemical Engineering, Vienna University of Technology, Getreidemarkt 9/166, A-1060 Vienna (Austria)

    2013-11-15

    Highlights: • MSW fly ash was thermally and hydrometallurgically treated to remove heavy metals. • More than 90% of easy volatile heavy metals (Cd and Pb) were removed thermally. • More than 90% of Cd, Cr, Cu an Zn were removed by alkaline – acid leaching. • The best results were obtained for the solution of 3 M NaOH and 2 M H{sub 2}SO{sub 4}. - Abstract: Heavy metals in fly ash from municipal solid waste incinerators are present in high concentrations. Therefore fly ash must be treated as a hazardous material. On the other hand, it may be a potential source of heavy metals. Zinc, lead, cadmium, and copper can be relatively easily removed during the thermal treatment of fly ash, e.g. in the form of chlorides. In return, wet extraction methods could provide promising results for these elements including chromium and nickel. The aim of this study was to investigate and compare thermal and hydrometallurgical treatment of municipal solid waste fly ash. Thermal treatment of fly ash was performed in a rotary reactor at temperatures between 950 and 1050 °C and in a muffle oven at temperatures from 500 to 1200 °C. The removal more than 90% was reached by easy volatile heavy metals such as cadmium and lead and also by copper, however at higher temperature in the muffle oven. The alkaline (sodium hydroxide) and acid (sulphuric acid) leaching of the fly ash was carried out while the influence of temperature, time, concentration, and liquid/solid ratio were investigated. The combination of alkaline-acidic leaching enhanced the removal of, namely, zinc, chromium and nickel.

  12. SOLIDIFICATION OF THE HANFORD LAW WASTE STREAM PRODUCED AS A RESULT OF NEAR-TANK CONTINUOUS SLUDGE LEACHING AND SODIUM HYDROXIDE RECOVERY

    Energy Technology Data Exchange (ETDEWEB)

    Reigel, M.; Johnson, F.; Crawford, C.; Jantzen, C.

    2011-09-20

    The U.S. Department of Energy (DOE), Office of River Protection (ORP), is responsible for the remediation and stabilization of the Hanford Site tank farms, including 53 million gallons of highly radioactive mixed wasted waste contained in 177 underground tanks. The plan calls for all waste retrieved from the tanks to be transferred to the Waste Treatment Plant (WTP). The WTP will consist of three primary facilities including pretreatment facilities for Low Activity Waste (LAW) to remove aluminum, chromium and other solids and radioisotopes that are undesirable in the High Level Waste (HLW) stream. Removal of aluminum from HLW sludge can be accomplished through continuous sludge leaching of the aluminum from the HLW sludge as sodium aluminate; however, this process will introduce a significant amount of sodium hydroxide into the waste stream and consequently will increase the volume of waste to be dispositioned. A sodium recovery process is needed to remove the sodium hydroxide and recycle it back to the aluminum dissolution process. The resulting LAW waste stream has a high concentration of aluminum and sodium and will require alternative immobilization methods. Five waste forms were evaluated for immobilization of LAW at Hanford after the sodium recovery process. The waste forms considered for these two waste streams include low temperature processes (Saltstone/Cast stone and geopolymers), intermediate temperature processes (steam reforming and phosphate glasses) and high temperature processes (vitrification). These immobilization methods and the waste forms produced were evaluated for (1) compliance with the Performance Assessment (PA) requirements for disposal at the IDF, (2) waste form volume (waste loading), and (3) compatibility with the tank farms and systems. The iron phosphate glasses tested using the product consistency test had normalized release rates lower than the waste form requirements although the CCC glasses had higher release rates than the

  13. Bio-extraction of precious metals from urban solid waste

    Science.gov (United States)

    Das, Subhabrata; Natarajan, Gayathri; Ting, Yen-Peng

    2017-01-01

    Reduced product lifecycle and increasing demand for electronic devices have resulted in the generation of huge volumes of electronic waste (e-waste). E-wastes contain high concentrations of toxic heavy metals, which have detrimental effects on health and the environment. However, e-wastes also contain significant concentrations of precious metals such as gold, silver and palladium, which can be a major driving force for recycling of urban waste. Cyanogenic bacteria such as Chromobacterium violaceum generate cyanide as a secondary metabolite which mobilizes gold into solution via a soluble gold-cyanide complex. However, compared to conventional technology for metal recovery, this approach is not effective, owing largely to the low concentration of lixiviants produced by the bacteria. To overcome the challenges of bioleaching of gold from e-waste, several strategies were adopted to enhance gold recovery rates. These included (i) pretreatment of e-waste to remove competing metal ions, (ii) mutation to adapt the bacteria to high pH environment, (iii) metabolic engineering to produce higher cyanide lixiviant, and (iv) spent medium leaching with adjusted initial pH. Compared to 7.1 % recovery by the wild type bacteria, these strategies achieved gold recoveries of 11.3%, 22.5%, 30% and 30% respectively at 0.5% w/v pulp density respectively. Bioleached gold was finally mineralized and precipitated as gold nanoparticles using the bacterium Delftia acidovorans. This study demonstrates the potential for enhancement of biocyanide production and gold recovery from electronic waste through different strategies, and extraction of solid gold from bioleached leachate.

  14. Effect of Nanometric Metallic Hydroxides on the Flame Retardant Properties of HDPE Composites

    Directory of Open Access Journals (Sweden)

    F. I. Beltrán-Ramírez

    2014-01-01

    Full Text Available The effect of nanometric magnesium and aluminum hydroxides on the flame retardancy of high density polyethylene was studied. Additionally, the effect of maleic anhydride grafted polyethylene (PEgMA and methyl acrylate grafted polyethylene (EMA compatibilizers, on the tensile properties, was also studied. Morphological characterization of nanocomposites was carried out by means of scanning transmission electron microscopy (STEM. Flame retardant properties of nanocomposites were evaluated by the UL-94 horizontal and vertical tests as well as by cone calorimeter tests. Thermal degradation behavior was analyzed with a thermogravimetric analyzer (TGA. Tensile tests were carried out according to ASTM D 638-03 in an Instron 4301 tensile testing machine. From STEM images, a good dispersion of flame retardants (MH and ATH in the polymer matrix was observed, which was reflected in the flame retardant properties. Results showed that the combination of nanometric MH and ATH produced excellent flame retardant properties, achieving a classification of V0 in the UL-94-V test and producing the lowest peak of heat release rate (PHRR and the lowest total heat released (THR in the cone calorimeter test. Finally, the addition of compatibilizer, especially PEgMA, resulted in much better tensile properties as compared to the noncompatibilized composition, maintaining the flame retardant properties.

  15. Method of handling radioactive alkali metal waste

    Science.gov (United States)

    Wolson, R.D.; McPheeters, C.C.

    Radioactive alkali metal is mixed with particulate silica in a rotary drum reactor in which the alkali metal is converted to the monoxide during rotation of the reactor to produce particulate silica coated with the alkali metal monoxide suitable as a feed material to make a glass for storing radioactive material. Silica particles, the majority of which pass through a 95 mesh screen or preferably through a 200 mesh screen, are employed in this process, and the preferred weight ratio of silica to alkali metal is 7 to 1 in order to produce a feed material for the final glass product having a silica to alkali metal monoxide ratio of about 5 to 1.

  16. Separating and recycling metals from mixed metallic particles of crushed electronic wastes by vacuum metallurgy.

    Science.gov (United States)

    Zhan, Lu; Xu, Zhenming

    2009-09-15

    During the treatment of electronic wastes, a crushing process is usually used to strip metals from various base plates. Several methods have been applied to separate metals from nonmetals. However, mixed metallic particles obtained from these processes are still a mixture of various metals, including some toxic heavy metals such as lead and cadmium. With emphasis on recovering copper and other precious metals, there have hitherto been no satisfactory methods to recover these toxic metals. In this paper, the criterion of separating metals from mixed metallic particles by vacuum metallurgy is built. The results show that the metals with high vapor pressure have been almost recovered completely, leading to a considerable reduction of environmental pollution. In addition, the purity of copper in mixed particles has been improved from about 80 wt % to over 98 wt %.

  17. Mining for metals in society's waste

    Science.gov (United States)

    Smith, Kathleen S.; Plumlee, Geoffrey S.; Hageman, Philip L.

    2015-01-01

    Metals are crucial to society and enable our modern standard of living. Look around and you can't help but see products made of metals. For instance, a typical gasoline-powered automobile contains over a ton of iron and steel, 240 pounds of aluminum, 42 pounds of copper, 41 pounds of silicon, 22 pounds of zinc and more than 30 other mineral commodities including titanium, platinum and gold.

  18. Purification of metal electroplating waste waters using zeolites.

    Science.gov (United States)

    Alvarez-Ayuso, E; García-Sánchez, A; Querol, X

    2003-12-01

    The sorption behaviour of natural (clinoptilolite) and synthetic (NaP1) zeolites has been studied with respect to Cr(III), Ni(II), Zn(II), Cu(II) and Cd(II) in order to consider its application to purify metal finishing waste waters. The batch method has been employed using metal concentrations in solution ranged from 10 to 200 mg/l and solid/liquid ratios ranged from 2.5 to 10 g/l. The Langmuir model was found to describe well all sorption processes, allowing to establish metal sorption sequences from which the main retention mechanism involved for each metal has been inferred. Synthetic zeolite exhibited about 10 times greater sorption capacities (b(Cr)=0.838 mmol/g, b(Ni)=0.342 mmol/g, b(Zn)=0.499 mmol/g, b(Cu)=0.795 mmol/g, b(Cd)=0.452 mmol/g) than natural zeolite (b(Cr)=0.079 mmol/g, b(Ni)=0.034 mmol/g, b(Zn)=0.053 mmol/g, b(Cu)=0.093 mmol/g, b(Cd)=0.041 mmol/g), appearing, therefore, as most suitable to perform metal waste water purification processes. This mineral showed the same high sorption capacity values when used in the purification of metal electroplating waste waters.

  19. Anaerobic bioleaching of metals from waste activated sludge

    Energy Technology Data Exchange (ETDEWEB)

    Meulepas, Roel J.W., E-mail: roel.meulepas@wetsus.nl [UNESCO-IHE, Westvest 7, 2611 AX Delft (Netherlands); Gonzalez-Gil, Graciela [UNESCO-IHE, Westvest 7, 2611 AX Delft (Netherlands); King Abdullah University of Science and Technology, Water Desalination and Reuse Center, Thuwal 13955-69000 (Saudi Arabia); Teshager, Fitfety Melese; Witharana, Ayoma [UNESCO-IHE, Westvest 7, 2611 AX Delft (Netherlands); Saikaly, Pascal E. [King Abdullah University of Science and Technology, Water Desalination and Reuse Center, Thuwal 13955-69000 (Saudi Arabia); Lens, Piet N.L. [UNESCO-IHE, Westvest 7, 2611 AX Delft (Netherlands)

    2015-05-01

    Heavy metal contamination of anaerobically digested waste activated sludge hampers its reuse as fertilizer or soil conditioner. Conventional methods to leach metals require aeration or the addition of leaching agents. This paper investigates whether metals can be leached from waste activated sludge during the first, acidifying stage of two-stage anaerobic digestion without the supply of leaching agents. These leaching experiments were done with waste activated sludge from the Hoek van Holland municipal wastewater treatment plant (The Netherlands), which contained 342 μg g{sup −1} of copper, 487 μg g{sup −1} of lead, 793 μg g{sup −1} of zinc, 27 μg g{sup −1} of nickel and 2.3 μg g{sup −1} of cadmium. During the anaerobic acidification of 3 g{sub dry} {sub weight} L{sup −1} waste activated sludge, 80–85% of the copper, 66–69% of the lead, 87% of the zinc, 94–99% of the nickel and 73–83% of the cadmium were leached. The first stage of two-stage anaerobic digestion can thus be optimized as an anaerobic bioleaching process and produce a treated sludge (i.e., digestate) that meets the land-use standards in The Netherlands for copper, zinc, nickel and cadmium, but not for lead. - Highlights: • Heavy metals were leached during anaerobic acidification of waste activated sludge. • The process does not require the addition of chelating or oxidizing agents. • The metal leaching efficiencies (66 to 99%) were comparable to chemical leaching. • The produced leachate may be used for metal recovery and biogas production. • The produced digested sludge may be used as soil conditioner.

  20. Towards zero waste production in the minerals and metals sector

    Science.gov (United States)

    Rankin, William J.

    The production of mineral and metal commodities results in large quantities of wastes (solid, liquid and gaseous) at each stage of value-adding — from mining to manufacturing. Waste production (both consumer and non-consumer) is a major contributor to environmental degradation. Approaches to waste management in the minerals industry are largely `after the event'. These have moved progressively from foul-and-flee to dilute-and-disperse to end end-of-pipe treatments. There is now a need to move to approaches which aim to reduce or eliminate waste production at source. Modern waste management strategies include the application of cleaner production principles, the use of wastes as raw materials, the reengineering of process flowsheets to minimise waste production, and use of industrial symbioses through industrial ecology to convert wastes into useful by-products. This paper examines how these can be adopted by the minerals industry, with some recent examples. The financial, technical, systemic and regulatory drivers and barriers are also examined.

  1. Electrochemical Corrosion Studies for Modeling Metallic Waste Form Release Rates

    Energy Technology Data Exchange (ETDEWEB)

    Poineau, Frederic [Univ. of Nevada, Las Vegas, NV (United States); Tamalis, Dimitri [Florida Memorial Univ., Miami Gardens, FL (United States)

    2016-08-01

    The isotope 99Tc is an important fission product generated from nuclear power production. Because of its long half-life (t1/2 = 2.13 ∙ 105 years) and beta-radiotoxicity (β⁻ = 292 keV), it is a major concern in the long-term management of spent nuclear fuel. In the spent nuclear fuel, Tc is present as an alloy with Mo, Ru, Rh, and Pd called the epsilon-phase, the relative amount of which increases with fuel burn-up. In some separation schemes for spent nuclear fuel, Tc would be separated from the spent fuel and disposed of in a durable waste form. Technetium waste forms under consideration include metallic alloys, oxide ceramics and borosilicate glass. In the development of a metallic waste form, after separation from the spent fuel, Tc would be converted to the metal, incorporated into an alloy and the resulting waste form stored in a repository. Metallic alloys under consideration include Tc–Zr alloys, Tc–stainless steel alloys and Tc–Inconel alloys (Inconel is an alloy of Ni, Cr and iron which is resistant to corrosion). To predict the long-term behavior of the metallic Tc waste form, understanding the corrosion properties of Tc metal and Tc alloys in various chemical environments is needed, but efforts to model the behavior of Tc metallic alloys are limited. One parameter that should also be considered in predicting the long-term behavior of the Tc waste form is the ingrowth of stable Ru that occurs from the radioactive decay of 99Tc (99Tc → 99Ru + β⁻). After a geological period of time, significant amounts of Ru will be present in the Tc and may affect its corrosion properties. Studying the effect of Ru on the corrosion behavior of Tc is also of importance. In this context, we studied the electrochemical behavior of Tc metal, Tc-Ni alloys (to model Tc-Inconel alloy) and Tc-Ru alloys in acidic media. The study of Tc-U alloys has also been performed in order to better understand the

  2. Melting of metallic intermediate level waste

    Energy Technology Data Exchange (ETDEWEB)

    Huutoniemi, Tommi; Larsson, Arne; Blank, Eva [Studsvik Nuclear AB, Nykoeping (Sweden)

    2013-08-15

    This report presents a feasibility study of a melting facility for core components and reactor internals. An overview is given of how such a facility for treatment of intermediate level waste might be designed, constructed and operated and highlights both the possibilities and challenges. A cost estimate and a risk analysis are presented in order to make a conclusion of the technical feasibility of such a facility. Based on the authors' experience in operating a low level waste melting facility, their conclusion is that without technical improvements such a facility is not feasible today. This is based on the cost of constructing and operating such a facility, in conjunction with the radiological risks associated with operation and the uncertain benefits to disposal and long term safety.

  3. Potential groundwater pollution from improper oil and metal waste ...

    African Journals Online (AJOL)

    Potential groundwater pollution from improper oil and metal waste disposal in Suame, Ghana. ... a helpful Frequently Asked Questions about PDFs. Alternatively, you can download the PDF file directly to your computer, from where it can be opened using a PDF reader. To download the PDF, click the Download link above.

  4. Removal of heavy metals from waste water of tanning leather ...

    African Journals Online (AJOL)

    LG

    2013-07-03

    Jul 3, 2013 ... are expensive, need energy and can produce waste products that require careful disposal (Ahalya et al.,. 2003). Therefore, the biological approaches have been considered as an alternative remediation for heavy metals removal from wastewaters (Pena-Castro et al.,. 2004). One of these methods is the ...

  5. Impact Of Municipal Solid Waste On Trace Metal Concentrations In ...

    African Journals Online (AJOL)

    The impact of municipal solid waste on the levels of cadmium, copper, nickel, lead and zinc in herbage and soil samples within Abuja municipality was studied. The flame atomic absorption spectrophotometry was used in the determination of the metals. The average concentration of Cd, Cu, Ni, Pb and Zn in the herbage ...

  6. Flexible Fiber-Shaped Supercapacitor Based on Nickel-Cobalt Double Hydroxide and Pen Ink Electrodes on Metallized Carbon Fiber.

    Science.gov (United States)

    Gao, Libo; Surjadi, James Utama; Cao, Ke; Zhang, Hongti; Li, Peifeng; Xu, Shang; Jiang, Chenchen; Song, Jian; Sun, Dong; Lu, Yang

    2017-02-15

    Flexible fiber-shaped supercapacitors (FSSCs) are recently of extensive interest for portable and wearable electronic gadgets. Yet the lack of industrial-scale flexible fibers with high conductivity and capacitance and low cost greatly limits its practical engineering applications. To this end, we here present pristine twisted carbon fibers (CFs) coated with a thin metallic layer via electroless deposition route, which exhibits exceptional conductivity with ∼300% enhancement and superior mechanical strength (∼1.8 GPa). Subsequently, the commercially available conductive pen ink modified high conductive composite fibers, on which uniformly covered ultrathin nickel-cobalt double hydroxides (Ni-Co DHs) were introduced to fabricate flexible FSSCs. The synthesized functionalized hierarchical flexible fibers exhibit high specific capacitance up to 1.39 F·cm -2 in KOH aqueous electrolyte. The asymmetric solid-state FSSCs show maximum specific capacitance of 28.67 mF·cm -2 and energy density of 9.57 μWh·cm -2 at corresponding power density as high as 492.17 μW·cm -2 in PVA/KOH gel electrolyte, with demonstrated high flexibility during stretching, demonstrating their potential in flexible electronic devices and wearable energy systems.

  7. Chemical Decontamination for Self-Disposal of Metal Wastes

    Energy Technology Data Exchange (ETDEWEB)

    Choi, Wangkyu; Yoon, Inho; Choi, Hyemin; Lee, Kunewoo; Moon, Jeikwon [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2013-05-15

    There are needs in metal waste volume reduction and self-disposal technology for enhancing the safety and economy in the management of large scale metal wastes such as retired SGs and RHs. In order to remove radionuclide contamination from the surface of materials, the variety of decontamination technologies have been developed in many countries. Chemical decontamination processes were originally designed to remove the radioactive deposit in order to reduce the radiation exposure to workers while operating the nuclear facilities. Diluted chemical solutions have been used to avoid damaging the system materials. On the other hand, in cases of the decontamination processes for decommissioning or recycling large components, it is greatly important to remove radioactive contamination completely by using a more aggressive solution. In this study, the effectiveness of metal surface decontamination using inorganic acid solutions such as HF/HNO{sub 3} and HF/H{sub 2}SO{sub 4} was investigated to evaluate the applicability of these processes to the decontamination of retired SGs. The chemical decontamination process using inorganic acid containing fluoride was investigated as a metal surface decontamination process for decommissioning and self-disposal of metal wastes. The HF/NaNO{sub 3} decontamination process that improves the existing HF/HNO{sub 3} decontamination process has been suggested as a decontamination process for retired SGs consisting of different types of system materials such as stainless steel and Inconel.

  8. Electrodialytic Removal of Heavy Metals from Different Solid Waste Products

    DEFF Research Database (Denmark)

    Ottosen, Lisbeth M.; Christensen, Iben Vernegren; Pedersen, Anne Juul

    2003-01-01

    A variety of heavy metal polluted waste products must be handled today. Electrochemical methods have been developed for remediation of polluted soil. One of the methods is the electrodialytic remediation method that is based on electromigration of heavy metal ions and ionic species within the soil...... matrix, and a separation of the soil and the process solutions, where the heavy metals are concentrated, with ion exchange membranes. For remediation of some soils, such as calcareous soils, it is necessary to add an enhancement solution. It was shown in a laboratory experiment that ammonium citrate...... could be used when removing Cu and Cr from a soil with 25% carbonates. The final concentrations of the elements were below the target values after the remediation. A question of whether the electrodialytic remediation method can be used for other waste products arose. Preliminary experiments showed...

  9. Aging of iron (hydr)oxides by heat treatment and effects on heavy metal binding

    DEFF Research Database (Denmark)

    Sørensen, Mette Abildgaard; Starckpoole, M. M.; Frenkel, A. I.

    2000-01-01

    their transformations caused by heat treatment prior to disposal or aging at a proper disposal site. The transformations were investigated by XRD, SEM, XANES, EXAFS, surface area measurements, pH static leaching tests, and extractions with oxalate and weak hydrochloric acid. It was found that at 600 and 900 °C the iron...... oxides were transformed to hematite, which had a greater thermodynamic stability but less surface area than the initial products. Heat treatment also caused some volatilization of heavy metals (most notably, Hg). Leaching with water at pH 9 (L/S 10, 24 h) and weak acid extraction showed that heat...

  10. Chemical stabilization of metals in mine wastes by transformed red mud and other iron compounds: laboratory tests.

    Science.gov (United States)

    Ardau, C; Lattanzi, P; Peretti, R; Zucca, A

    2014-01-01

    A series of static and kinetic laboratory-scale tests were designed in order to evaluate the efficacy of transformed red mud (TRM) from bauxite refining residues, commercial zero-valent iron, and synthetic iron (III) hydroxides as sorbents/reagents to minimize the generation of acid drainage and the release of toxic elements from multi-contaminant-laden mine wastes. In particular, in some column experiments the percolation of meteoric water through a waste pile, alternated with periods of dryness, was simulated. Wastes were placed in columns together with sorbents/reagents in three different set-ups: as blended amendment (mixing method), as a bed at the bottom of the column (filtration method), or as a combination of the two previous methods. The filtration methods, which simulate the creation of a permeable reactive barrier downstream of a waste pile, are the most effective, while the use of sorbents/reagents as amendments leads to unsatisfactory results, because of the selective removal of only some contaminants. The efficacy of the filtration method is not significantly affected by the periods of dryness, except for a temporary rise of metal contents in the leachates due to dissolution of soluble salts formed upon evaporation in the dry periods. These results offer original information on advantages/limits in the use of TRM for the treatment of multi-contaminant-laden mine wastes, and represent the starting point for experimentation at larger scale.

  11. Anaerobic bioleaching of metals from waste activated sludge.

    Science.gov (United States)

    Meulepas, Roel J W; Gonzalez-Gil, Graciela; Teshager, Fitfety Melese; Witharana, Ayoma; Saikaly, Pascal E; Lens, Piet N L

    2015-05-01

    Heavy metal contamination of anaerobically digested waste activated sludge hampers its reuse as fertilizer or soil conditioner. Conventional methods to leach metals require aeration or the addition of leaching agents. This paper investigates whether metals can be leached from waste activated sludge during the first, acidifying stage of two-stage anaerobic digestion without the supply of leaching agents. These leaching experiments were done with waste activated sludge from the Hoek van Holland municipal wastewater treatment plant (The Netherlands), which contained 342 μg g(-1) of copper, 487 μg g(-1) of lead, 793 μg g(-1) of zinc, 27 μg g(-1) of nickel and 2.3 μg g(-1) of cadmium. During the anaerobic acidification of 3 gdry weight L(-1) waste activated sludge, 80-85% of the copper, 66-69% of the lead, 87% of the zinc, 94-99% of the nickel and 73-83% of the cadmium were leached. The first stage of two-stage anaerobic digestion can thus be optimized as an anaerobic bioleaching process and produce a treated sludge (i.e., digestate) that meets the land-use standards in The Netherlands for copper, zinc, nickel and cadmium, but not for lead. Copyright © 2014 Elsevier B.V. All rights reserved.

  12. Anaerobic bioleaching of metals from waste activated sludge

    KAUST Repository

    Meulepas, Roel J W

    2015-05-01

    Heavy metal contamination of anaerobically digested waste activated sludge hampers its reuse as fertilizer or soil conditioner. Conventional methods to leach metals require aeration or the addition of leaching agents. This paper investigates whether metals can be leached from waste activated sludge during the first, acidifying stage of two-stage anaerobic digestion without the supply of leaching agents. These leaching experiments were done with waste activated sludge from the Hoek van Holland municipal wastewater treatment plant (The Netherlands), which contained 342μgg-1 of copper, 487μgg-1 of lead, 793μgg-1 of zinc, 27μgg-1 of nickel and 2.3μgg-1 of cadmium. During the anaerobic acidification of 3gdry weightL-1 waste activated sludge, 80-85% of the copper, 66-69% of the lead, 87% of the zinc, 94-99% of the nickel and 73-83% of the cadmium were leached. The first stage of two-stage anaerobic digestion can thus be optimized as an anaerobic bioleaching process and produce a treated sludge (i.e., digestate) that meets the land-use standards in The Netherlands for copper, zinc, nickel and cadmium, but not for lead.

  13. Evaluating waste management strategies. A case of metal-contaminated waste wood

    Energy Technology Data Exchange (ETDEWEB)

    Krook, J.; Maartensson, A.; Eklund, M. [Environmental Technology and Management, Department of Mechanical Engineering, Linkoeping University, SE-581 83 Linkoeping (Sweden)

    2007-11-15

    In Sweden recovered waste wood (RWW) is used for heat production, which reduces the share of waste that is landfilled and recovers the energy content of the waste. However, this waste contains contaminated materials that pollute RWW with heavy metals, causing downstream environmental problems. The main objective of this study was to analyse how different upstream-oriented strategies to manage RWW, influence the arising of environmental pressures downstream the waste management system. Today, the contaminated materials in RWW are handled together with the main waste flow. This upstream approach was compared with a separation strategy that removes contaminants from the main waste flow thereby handling these materials separately downstream the waste management system. An extended substance flow analysis (SFA) methodology that also includes resource issues was applied for the analysis. The results show that the upstream separation strategy exhibits potential environmental benefits. However, to accurately prevent environmental pollution also in a long time perspective, upstream separation strategies must be combined with downstream measures aimed to immobilise the contaminants in by-products. Otherwise, such separation strategies, as the current handling of RWW, may cause temporal and spatial shifting of problems. To enable immobilising measures, however, upstream separation strategies are important since they decrease the volume problem. (author)

  14. Corrosion of Metal Inclusions In Bulk Vitrification Waste Packages

    Energy Technology Data Exchange (ETDEWEB)

    Bacon, Diana H.; Pierce, Eric M.; Wellman, Dawn M.; Strachan, Denis M.; Josephson, Gary B.

    2006-07-31

    The primary purpose of the work reported here is to analyze the potential effect of the release of technetium (Tc) from metal inclusions in bulk vitrification waste packages once they are placed in the Integrated Disposal Facility (IDF). As part of the strategy for immobilizing waste from the underground tanks at Hanford, selected wastes will be immobilized using bulk vitrification. During analyses of the glass produced in engineering-scale tests, metal inclusions were found in the glass product. This report contains the results from experiments designed to quantify the corrosion rates of metal inclusions found in the glass product from AMEC Test ES-32B and simulations designed to compare the rate of Tc release from the metal inclusions to the release of Tc from glass produced with the bulk vitrification process. In the simulations, the Tc in the metal inclusions was assumed to be released congruently during metal corrosion as soluble TcO4-. The experimental results and modeling calculations show that the metal corrosion rate will, under all conceivable conditions at the IDF, be dominated by the presence of the passivating layer and corrosion products on the metal particles. As a result, the release of Tc from the metal particles at the surfaces of fractures in the glass releases at a rate similar to the Tc present as a soluble salt. The release of the remaining Tc in the metal is controlled by the dissolution of the glass matrix. To summarize, the release of 99Tc from the BV glass within precipitated Fe is directly proportional to the diameter of the Fe particles and to the amount of precipitated Fe. However, the main contribution to the Tc release from the iron particles is over the same time period as the release of the soluble Tc salt. For the base case used in this study (0.48 mass% of 0.5 mm diameter metal particles homogeneously distributed in the BV glass), the release of 99Tc from the metal is approximately the same as the release from 0.3 mass% soluble Tc

  15. Adsorption of heavy metals in waste water using biological materials

    Directory of Open Access Journals (Sweden)

    Candelaria Tejada-Tovar

    2015-01-01

    Full Text Available Biosorption is a process that allows active or passive uptake of metal ions due to the property that different living or dead biomass have to bind and accumulate these pollutants by different mechanisms. The application of low-cost materials obtained from different biomass from microbial flora, agro-industrial waste and algae has been investigated to replace the use of conventional methods for the removal of contaminants such as heavy metals. Some of the metals of greatest impact to the environment due to its high toxicity and difficult to remove are chromium, nickel, cadmium, lead, and mercury. In this paper, an overview of adsorption as an alternative process for the removal of contaminants in solution and biomass commonly used in these processes, as well as some of the modifications made to improve the efficiency of adsorption of these materials is presented. It was concluded that the use of adsorption in the removal of pollutants in aqueous solution using waste biomass is applicable to these decontamination processes avoiding subsequent problems such as the generation of chemical sludge, and generating an alternative to use materials considered as waste. It is further identified that such factors as the pH of the solution, particle size, temperature, and concentration of metal effect on the process.

  16. Competitive adsorption of metals on cabbage waste from multi-metal solutions.

    Science.gov (United States)

    Hossain, M A; Ngo, H H; Guo, W S; Nghiem, L D; Hai, F I; Vigneswaran, S; Nguyen, T V

    2014-05-01

    This study assessed the adsorption capacity of the agro-waste 'cabbage' as a biosorbent in single, binary, ternary and quaternary sorption systems with Cu(II), Pb(II), Zn(II) and Cd(II) ions. Dried and ground powder of cabbage waste (CW) was used for the sorption of metals ions. Carboxylic, hydroxyl, and amine groups in cabbage waste were found to be the key functional groups for metal sorption. The adsorption isotherms obtained could be well fitted to both the mono- and multi-metal models. In the competitive adsorption systems, cabbage waste adsorbed larger amount of Pb(II) than the other three metals. However, the presence of the competing ions suppressed the sorption of the target metal ions. Except the case of binary system of Cd(II)-Zn(II) and Cd(II)-Cu(II), there was a linear inverse dependency between the sorption capacities and number of different types of competitive metal ions. Copyright © 2013 Elsevier Ltd. All rights reserved.

  17. Pollution prevention and waste minimization in metal finishing

    Energy Technology Data Exchange (ETDEWEB)

    Stimetz, C.J.

    1994-12-01

    This study was done to identify pollution prevention and waste minimization opportunities in the general plating department and the printed circuit board processing department. Recommendations for certain recycle and recovery technologies were mad in order to reduce usage of acids and the volume of heavy metal sludge that is formed at the industrial Wastewater Pretreatment Facility (IWPF). Some of these technologies discussed were acid purification, electrowinning, and ion exchange. Specific technologies are prescribed for specific processes. Those plating processes where the metals can be recovered are copper, nickel, gold, cadmium, tin, lead, and rhodium.

  18. Froth flotation of oil-bearing metal sulfide wastes

    Energy Technology Data Exchange (ETDEWEB)

    Miller, R.L. [Idaho National Engineering Lab., Idaho Falls, ID (United States); Atwood, R.L.; Ye, Yi [Advanced Processing Technologies, Inc., Salt Lake City, UT (United States)

    1991-12-01

    An industrial wastewater, including plating wastes, is treated with sodium sulfide and ferrous sulfate to form a sulfide-oxide precipitate containing chromium and other toxic metals. Hydrocarbons, in the water, coat the sulfide-oxide particles, impeding metal recovery. Froth flotation, without reagent addition, was found to recover 93.9% of the solids from the sludge with simultaneous rejection of 89% of the water. Methyl isobutyl carbinol (MIBC) improved recovery and potassium amyl xanthate improved both recovery and grade. The process design has wastewater feed (without MIBC) to the rougher circuit. The rougher concentrate is conditioned with MIBC and fed to a cleaner circuit to achieve a high grade concentrate. About 95% of the water is recirculated to the waste treatment plant. 3 refs., 3 figs., 4 tabs.

  19. Froth flotation of oil-bearing metal sulfide wastes

    Energy Technology Data Exchange (ETDEWEB)

    Miller, R.L. (Idaho National Engineering Lab., Idaho Falls, ID (United States)); Atwood, R.L.; Ye, Yi (Advanced Processing Technologies, Inc., Salt Lake City, UT (United States))

    1991-01-01

    An industrial wastewater, including plating wastes, is treated with sodium sulfide and ferrous sulfate to form a sulfide-oxide precipitate containing chromium and other toxic metals. Hydrocarbons, in the water, coat the sulfide-oxide particles, impeding metal recovery. Froth flotation, without reagent addition, was found to recover 93.9% of the solids from the sludge with simultaneous rejection of 89% of the water. Methyl isobutyl carbinol (MIBC) improved recovery and potassium amyl xanthate improved both recovery and grade. The process design has wastewater feed (without MIBC) to the rougher circuit. The rougher concentrate is conditioned with MIBC and fed to a cleaner circuit to achieve a high grade concentrate. About 95% of the water is recirculated to the waste treatment plant. 3 refs., 3 figs., 4 tabs.

  20. Determination of Heavy Metal Levels in Various Industrial Waste Waters

    Directory of Open Access Journals (Sweden)

    Mustafa Şahin Dündar

    2012-06-01

    Full Text Available Important part of the environmetal pollution consists of waste water and water pollution. The water polluted by anthropogenical, industrial, and agricultural originated sources are defined as waste waters which are the main pollution sources for reservoirs, rivers, lakes, and seas. In this work, waste waters of leather, textile, automotive side, and metal plating industries were used to determine the levels of Cu, Zn, Cr, Pb and Ni by using Flame Atomic Absorption Spectrometer. As a result, highest mean levels of copper in supernatants of plating and textile industries were observed as 377,18 ng ml-1, respectively 103 ng ml-1 lead and 963,6 ng ml-1 nickel in plating industry, 1068,2 ng ml-1 zinc and 14557,1 ng ml-1 chromium in plating and leather industries were determined.

  1. Heavy metal evaporation kinetics in thermal waste treatment processes

    Energy Technology Data Exchange (ETDEWEB)

    Ludwig, Ch.; Stucki, S.; Schuler, A.J. [Paul Scherrer Inst. (PSI), Villigen (Switzerland)

    1999-08-01

    To investigate the evaporation kinetics of heavy metals, experiments were performed by conventional thermogravimetry and a new method using Inductively Coupled Plasma Optical Emission Spectroscopy (ICP-OES). The new method allows online measurements in time intervals that are typically below one minute. The evaporation of Cd, Cu, Pb, and Zn from synthetic mixtures and filter ashes from municipal solid waste incineration (MSWI) was of major interest. (author) 2 figs., 4 refs.

  2. Heavy metals in the waste and in the water discharge area of municipal solid waste

    Directory of Open Access Journals (Sweden)

    Luiz Ermindo Cavallet

    2013-12-01

    Full Text Available The county of Paranaguá discards 80 tons of municipal solid waste (MSW daily in the Embocuí landfill without proper treatment. The present study aimed to evaluate the concentration of arsenic (As, cadmium (Cd, chromium (Cr, lead (Pb and mercury (Hg in the dump area and to compare it with reference values for soil and water quality stipulated by CETESB (2005. The methodology of the study involved the collection of waste samples (organic waste mixed with soil from a depth of 1 m deep at 12 points of the dump, and the collection of water samples from a depth of 3 m at 3 points in the deposited waste. Extraction of heavy metals in the water samples was performed according to the USEPA (1999 method and analysis followed ICP-OES (Inductively Coupled Plasma - Atomic Emission Spectrometry. Analysis of the solid waste samples showed the following concentrations: (mg kg -1: As < 10; Cd < 1; Cr = 26; Pb = 52; e Hg = 0.2. The water samples showed the following concentrations: (mg L- 1: As < 5; Cd < 5; Cr =29 e Pb = 10. The amounts of heavy metals in samples of tailings and water from the landfill area fall below the values considered to create a risk of contamination.

  3. Assessment of toxic metals in waste personal computers

    Energy Technology Data Exchange (ETDEWEB)

    Kolias, Konstantinos; Hahladakis, John N., E-mail: john_chach@yahoo.gr; Gidarakos, Evangelos, E-mail: gidarako@mred.tuc.gr

    2014-08-15

    Highlights: • Waste personal computers were collected and dismantled in their main parts. • Motherboards, monitors and plastic housing were examined in their metal content. • Concentrations measured were compared to the RoHS Directive, 2002/95/EC. • Pb in motherboards and funnel glass of devices released <2006 was above the limit. • Waste personal computers need to be recycled and environmentally sound managed. - Abstract: Considering the enormous production of waste personal computers nowadays, it is obvious that the study of their composition is necessary in order to regulate their management and prevent any environmental contamination caused by their inappropriate disposal. This study aimed at determining the toxic metals content of motherboards (printed circuit boards), monitor glass and monitor plastic housing of two Cathode Ray Tube (CRT) monitors, three Liquid Crystal Display (LCD) monitors, one LCD touch screen monitor and six motherboards, all of which were discarded. In addition, concentrations of chromium (Cr), cadmium (Cd), lead (Pb) and mercury (Hg) were compared with the respective limits set by the RoHS 2002/95/EC Directive, that was recently renewed by the 2012/19/EU recast, in order to verify manufacturers’ compliance with the regulation. The research included disassembly, pulverization, digestion and chemical analyses of all the aforementioned devices. The toxic metals content of all samples was determined using Inductively Coupled Plasma-Mass Spectrometry (ICP-MS). The results demonstrated that concentrations of Pb in motherboards and funnel glass of devices with release dates before 2006, that is when the RoHS Directive came into force, exceeded the permissible limit. In general, except from Pb, higher metal concentrations were detected in motherboards in comparison with plastic housing and glass samples. Finally, the results of this work were encouraging, since concentrations of metals referred in the RoHS Directive were found in

  4. Recovery of heavy metals from intractable wastes: A thermal approach

    Energy Technology Data Exchange (ETDEWEB)

    Kirk, D.W. [Univ. of Toronto (Canada)

    1996-12-31

    The generation of industrial solid wastes containing leachable species of environmental concern is a problem for developing and developed nations alike. These materials arise from direct processing of mineral ores, from production of metals and minerals, from manufacturing operations, and from air and water pollution treatment processes. The general characteristics that make these wastes intractable is that their content of hazardous species is not easily liberated from the waste yet is not bound so tightly that they are safe for landfill disposal or industrial use. The approach taken in this work is a thermal treatment that separates the inorganic contaminants from the wastes. The objective is to provide recovery and reuse of both the residual solids and liberated contaminants. The results from operating this technique using two very different types of waste are described. The reasons that the process will work for a wide variety of wastes are explored. By using the knowledge of the thermodynamic stability of the phases found from the characterization analyses, a thermal regime was found that allowed separation of the contaminants without capturing the matrix materials. Bench scale studies were carried out using a tube furnace. Samples of the wastes were heated in crucible boats from 750 to 1150{degrees}C in the presence of various chlorinating agents. The offgas contained 90{sup +}% of the targeted contaminants despite their complex matrix form. The residue was free of contamination. As a result of the efficient concentrating mechanism of the process, the contaminants in the offgas solids are attractive for reuse in metallurgical industries. As an additional benefit, the organic contaminants of the residues were eliminated. Dioxin traces in the solids before treatment were absent after treatment. 15 refs., 4 figs., 4 tabs.

  5. The state of the art on the radioactive metal waste recycling technologies

    Energy Technology Data Exchange (ETDEWEB)

    Oh, Won Jin; Moon, Jei Kwon; Jung, Chong Hun; Park, Sang Yoon

    1997-09-01

    As the best strategy to manage the radioactive metal wastes which are generated during operation and decommissioning of nuclear facilities, the following recycling technologies are investigated. 1. decontamination technologies for radioactive metal waste recycling 2. decontamination waste treatment technologies. 3. residual radioactivity evaluation technologies. (author). 260 refs., 26 tabs., 31 figs

  6. Bacterial Treatment and Metal Characterization of Biomedical Waste Ash

    Directory of Open Access Journals (Sweden)

    Shelly Heera

    2014-01-01

    Full Text Available Biomedical waste ash generated due to the incineration of biomedical waste contains large amounts of heavy metals and polycyclic aromatic hydrocarbons (PAHs, which is disposed of in regular landfills, and results in unfavorable amounts of hazardous materials seeping into the ground and may pollute surface water and groundwater. Therefore, it is essential to remove the toxicity of ash before disposal into landfills or reutilization. Environmental characteristic analysis of BMW ash showed increased hardness (1320 mg/L and chloride (8500 mg/L content in leachate compared to World Health Organization (WHO and Environment Protection Agency (EPA guidelines for drinking water (hardness, 300 mg/L; chloride, 250 mg/L. The alkalinity and pH of the ash leachate were 400 mg/L and 8.35, respectively. In this paper, study was carried out to investigate the metal tolerance level of bacterial isolates isolated from soil. The isolate Bacillus sp. KGMDI can tolerate up to 75 mg/L of metal concentration (Mn, Mo, Cr, Fe, Cu, and Zn in enriched growth medium. This shows that the isolated culture is capable of growing in presence of high concentration of heavy metals and acts as potential biological tool to reduce the negative impact of BMW ash on the environment during landfilling.

  7. Clay minerals, metallic oxides and oxy-hydroxides and soil organic carbon distribution within soil aggregates in temperate forest soils

    Science.gov (United States)

    Gartzia-Bengoetxea, Nahia; Fernández-Ugalde, Oihane; Virto, Iñigo; Arias-González, Ander

    2017-04-01

    Soil mineralogy is of primary importance for key environmental services provided by soils like carbon sequestration. However, current knowledge on the effects of clay mineralogy on soil organic carbon (SOC) stabilization is based on limited and conflicting data. In this study, we investigated the relationship between clay minerals, metallic oxides and oxy-hydroxides and SOC distribution within soil aggregates in mature Pinus radiata D.Don forest plantations. Nine forest stands located in the same geographical area of the Basque Country (North of Spain) were selected. These stands were planted on different parent material (3 on each of the following: sandstone, basalt and trachyte). There were no significant differences in climate and forest management among them. Moreover, soils under these plantations presented similar content of clay particles. We determined bulk SOC storage, clay mineralogy, the content of Fe-Si-Al-oxides and oxyhydroxides and the distribution of organic C in different soil aggregate sizes at different soil depths (0-5 cm and 5-20 cm). The relationship between SOC and abiotic factors was investigated using a factor analysis (PCA) followed by stepwise regression analysis. Soils developed on sandstone showed significantly lower concentration of SOC (29 g C kg-1) than soils developed on basalts (97 g C kg-1) and trachytes (119 g C kg-1). The soils on sandstone presented a mixed clay mineralogy dominated by illite, with lesser amounts of hydroxivermiculite, hydrobiotite and kaolinite, and a total absence of interstratified chlorite/vermiculite. In contrast, the major crystalline clay mineral identified in the soils developed on volcanic rocks was interstratified chlorite/vermiculite. Nevertheless, no major differences were observed between basaltic and trachytic soils in the clay mineralogy. The selective extraction of Fe showed that the oxalate extractable iron was significantly lower in soils on sandstone (3.7%) than on basalts (11.2%) and

  8. A review on human health consequences of metals exposure to e-waste in China.

    Science.gov (United States)

    Song, Qingbin; Li, Jinhui

    2015-01-01

    As the world's the largest dumping ground for e-waste, much of the population in China is exposed to heavy metals due to informal e-waste recycling processes. We reviewed recent studies on body burdens and human health effects of heavy metals from the major e-waste recycling sites in China. The results showed that the residents in the e-waste recycling sites are facing a potential higher daily intake of heavy metals. Moreover, heavy metals had entered subjects' bodies (the collected 5 tissue samples). Additionally,individual exposure to heavy metals in e-waste has also caused negative health outcomes,especially in neonates and children. We also recorded plausible outcomes associated with exposure to e wast (to heavy metals). A precautionary approach toward exposure, especially in neonates and children, therefore seems warranted.

  9. Metallic elements occurrences within metallic fragments in the municipal waste incineration bottom ash

    Science.gov (United States)

    Kowalski, Piotr; Kasina, Monika; Michalik, Marek

    2017-04-01

    Bottom ash (BA) from municipal solid waste incineration (MSWI) is composed of grainy ash material, residual components and metallic fragments (from few µm up to 3-5 cm). Its mineral and chemical composition is related to the composition of the waste stream in the incinerator operational area. Wide use of thermal techniques in management of solid waste makes important the studies on valuable components and their distribution within the material in terms of their further processing. By using various valorization or extraction techniques it is possible to extend the range of its possible further application. To investigate metallic elements distribution within metallic fragments of the MSWI BA material produced in municipal waste incineration plant in Poland were collected in 2015 and 2016. BA and its components were investigated using spectroscopic methods of chemical analysis: ICP-OES, ICP-MS, LECO and EDS (used for microanalysis during SEM observations). BA is a material rich in Si (22.5 wt%), Ca (13.4 wt%), Fe (4 wt%), Al (5.2 wt%) and Na (3.5 wt%), composed of equal part of amorphous (silicate glass dominated) and crystalline phase (rich in silicates, aluminosilicates, oxides of non- and metallic elements and sulphates). The content of metallic elements (Al, Fe, Mg, Ti, Mn, Cr, Ni, Sc, Mo, Cu, Pb, Zn, Sn) is 11.5 wt% with domination of Al (5.2 wt%) and Fe (4 wt%) and elevated values of Mg (1 wt%), Ti (0.54 wt%), Cu (0.26 wt%) and Zn (0.27 wt%) (Kowalski et al., 2016). They were mostly concentrated in the form of metallic fragments, mainly as metallic inclusions in the size of 1-20 µm and separated metallic grains in the size of 50-300 µm. Metallic fragments present in the BA are characterized by their composition heterogeneity and various oxygen content. Fragments are rarely composed of single metallic element and usually in their composition up to few main elements dominated over others. The most common were Fe-, Al- and Zn-rich fragments forming respectively

  10. Transmission electron microscopy analysis of corroded metal waste forms.

    Energy Technology Data Exchange (ETDEWEB)

    Dietz, N. L.

    2005-04-15

    This report documents the results of analyses with transmission electron microscopy (TEM) combined with energy dispersive X-ray spectroscopy (EDS) and selected area electron diffraction (ED) of samples of metallic waste form (MWF) materials that had been subjected to various corrosion tests. The objective of the TEM analyses was to characterize the composition and microstructure of surface alteration products which, when combined with other test results, can be used to determine the matrix corrosion mechanism. The examination of test samples generated over several years has resulted in refinements to the TEM sample preparation methods developed to preserve the orientation of surface alteration layers and the underlying base metal. The preservation of microstructural spatial relationships provides valuable insight for determining the matrix corrosion mechanism and for developing models to calculate radionuclide release in repository performance models. The TEM results presented in this report show that oxide layers are formed over the exposed steel and intermetallic phases of the MWF during corrosion in aqueous solutions and humid air at elevated temperatures. An amorphous non-stoichiometric ZrO{sub 2} layer forms at the exposed surfaces of the intermetallic phases, and several nonstoichiometric Fe-O layers form over the steel phases in the MWF. These oxide layers adhere strongly to the underlying metal, and may be overlain by one or more crystalline Fe-O phases that probably precipitated from solution. The layer compositions are consistent with a corrosion mechanism of oxidative dissolution of the steel and intermetallic phases. The layers formed on the steel and intermetallic phases form a continuous layer over the exposed waste form, although vertical splits in the layer and corrosion in pits and crevices were seen in some samples. Additional tests and analyses are needed to verify that these layers passivate the underlying metals and if passivation can break

  11. Recycling of waste printed circuit boards with simultaneous enrichment of special metals by using alkaline melts: A green and strategically advantageous solution.

    Science.gov (United States)

    Stuhlpfarrer, Philipp; Luidold, Stefan; Antrekowitsch, Helmut

    2016-04-15

    The increasing consumption of electric and electronic equipment has led to a rise in toxic waste. To recover the metal fraction, a separation of the organic components is necessary because harmful substances such as chlorine, fluorine and bromine cause ecological damage, for example in the form of dioxins and furans at temperature above 400°C. Hence, an alternative, environmentally friendly approach was investigated exploiting that a mixture of caustic soda and potassium hydroxide in eutectic composition melts below 200°C, enabling a fast cracking of the long hydrocarbon chains. The trials demonstrate the removal of organic compounds without a loss of copper and precious metals, as well as a suppressed formation of hazardous off-gases. In order to avoid an input of alkaline elements into the furnace and ensuing problems with refractory materials, a washing step generates a sodium and potassium hydroxide solution, in which special metals like indium, gallium and germanium are enriched. Their concentrations facilitate the recovery of these elements, because otherwise they become lost in the typical recycling processes. The aim of this work was to find an environmental solution for the separation of plastics and metals as well as a strategically important answer for the recycling of printed circuit boards and mobile phones. Copyright © 2015 Elsevier B.V. All rights reserved.

  12. Recycling of waste printed circuit boards with simultaneous enrichment of special metals by using alkaline melts: A green and strategically advantageous solution

    Energy Technology Data Exchange (ETDEWEB)

    Stuhlpfarrer, Philipp, E-mail: philipp-johannes.stuhlpfarrer@stud.unileoben.ac.at; Luidold, Stefan; Antrekowitsch, Helmut

    2016-04-15

    Highlights: • Removal of plastics. • Enrichment of In, Ga and Ge. • Low temperature. • No dioxines. - Abstract: The increasing consumption of electric and electronic equipment has led to a rise in toxic waste. To recover the metal fraction, a separation of the organic components is necessary because harmful substances such as chlorine, fluorine and bromine cause ecological damage, for example in the form of dioxins and furans at temperature above 400 °C. Hence, an alternative, environmentally friendly approach was investigated exploiting that a mixture of caustic soda and potassium hydroxide in eutectic composition melts below 200 °C, enabling a fast cracking of the long hydrocarbon chains. The trials demonstrate the removal of organic compounds without a loss of copper and precious metals, as well as a suppressed formation of hazardous off-gases. In order to avoid an input of alkaline elements into the furnace and ensuing problems with refractory materials, a washing step generates a sodium and potassium hydroxide solution, in which special metals like indium, gallium and germanium are enriched. Their concentrations facilitate the recovery of these elements, because otherwise they become lost in the typical recycling processes. The aim of this work was to find an environmental solution for the separation of plastics and metals as well as a strategically important answer for the recycling of printed circuit boards and mobile phones.

  13. Soil Pollution by Toxic Metals near E-waste Recycling Operations in Ibadan, Nigeria

    National Research Council Canada - National Science Library

    Adesokan, Michael D; Adie, Gilbert U; Osibanjo, Oladele

    2016-01-01

    Background. Unsound recycling of e-waste releases toxic metals into environmental media and has deleterious health consequences to humans as the metals transfer to humans through the food chain, direct contact and inhalation. Objectives...

  14. Assessment of toxic metals in waste personal computers.

    Science.gov (United States)

    Kolias, Konstantinos; Hahladakis, John N; Gidarakos, Evangelos

    2014-08-01

    Considering the enormous production of waste personal computers nowadays, it is obvious that the study of their composition is necessary in order to regulate their management and prevent any environmental contamination caused by their inappropriate disposal. This study aimed at determining the toxic metals content of motherboards (printed circuit boards), monitor glass and monitor plastic housing of two Cathode Ray Tube (CRT) monitors, three Liquid Crystal Display (LCD) monitors, one LCD touch screen monitor and six motherboards, all of which were discarded. In addition, concentrations of chromium (Cr), cadmium (Cd), lead (Pb) and mercury (Hg) were compared with the respective limits set by the RoHS 2002/95/EC Directive, that was recently renewed by the 2012/19/EU recast, in order to verify manufacturers' compliance with the regulation. The research included disassembly, pulverization, digestion and chemical analyses of all the aforementioned devices. The toxic metals content of all samples was determined using Inductively Coupled Plasma-Mass Spectrometry (ICP-MS). The results demonstrated that concentrations of Pb in motherboards and funnel glass of devices with release dates before 2006, that is when the RoHS Directive came into force, exceeded the permissible limit. In general, except from Pb, higher metal concentrations were detected in motherboards in comparison with plastic housing and glass samples. Finally, the results of this work were encouraging, since concentrations of metals referred in the RoHS Directive were found in lower levels than the legislative limits. Copyright © 2014 Elsevier Ltd. All rights reserved.

  15. Comparative assessment of metallurgical recovery of metals from electronic waste with special emphasis on bioleaching.

    Science.gov (United States)

    Priya, Anshu; Hait, Subrata

    2017-03-01

    Waste electrical and electronic equipment (WEEE) or electronic waste (e-waste) is one of the fastest growing waste streams in the urban environment worldwide. The core component of printed circuit board (PCB) in e-waste contains a complex array of metals in rich quantity, some of which are toxic to the environment and all of which are valuable resources. Therefore, the recycling of e-waste is an important aspect not only from the point of waste treatment but also from the recovery of metals for economic growth. Conventional approaches for recovery of metals from e-waste, viz. pyrometallurgical and hydrometallurgical techniques, are rapid and efficient, but cause secondary pollution and economically unviable. Limitations of the conventional techniques have led to a shift towards biometallurgical technique involving microbiological leaching of metals from e-waste in eco-friendly manner. However, optimization of certain biotic and abiotic factors such as microbial species, pH, temperature, nutrients, and aeration rate affect the bioleaching process and can lead to profitable recovery of metals from e-waste. The present review provides a comprehensive assessment on the metallurgical techniques for recovery of metals from e-waste with special emphasis on bioleaching process and the associated factors.

  16. Hydrometallurgical Recovery of Precious Metals and Removal of Hazardous Metals Using Persimmon Tannin and Persimmon Wastes

    Directory of Open Access Journals (Sweden)

    Katsutoshi Inoue

    2015-10-01

    Full Text Available Novel and environmentally benign adsorbents were prepared via a simple sulfuric acid treatment process using the wastes of astringent persimmon, a type of biomass waste, along with persimmon tannin extract which is currently employed for the tanning of leather and as natural dyes and paints. The effectiveness of these new biosorbents was exemplified with regards to hydrometallurgical and environmental engineering applications for the adsorptive removal of uranium and thorium from rare earths, cesium from other alkaline metals such as sodium, hexa-valent chromium from zinc as well as adsorptive recovery of gold from chloride media. Furthermore, reductive coagulation of gold from chloride media for the direct recovery of metallic gold and adsorptive recovery of palladium and platinum using chemically modified persimmon tannin extract were studied. OPEN

  17. Metals, non-metals and PCB in electrical and electronic waste--actual levels in Switzerland.

    Science.gov (United States)

    Morf, Leo S; Tremp, Josef; Gloor, Rolf; Schuppisser, Felix; Stengele, Markus; Taverna, Ruedi

    2007-01-01

    The chemical composition of waste of small electrical and electronic equipment (s-WEEE), a rapidly growing waste stream, was determined for selected metals (Cu, Sb, Hg etc.) and non-metals (Cl, Br, P) and PCBs. During a 3-day experiment, all output products and the s-WEEE input mass flows in a WEEE recycling plant were measured. Only output products were sampled and analyzed. Material balances were established, applying substance flow analysis (SFA). Transfer coefficients for the selected substances were also determined. The results demonstrate the capability of SFA to determine the composition of the highly heterogeneous WEEE for most substances with rather low uncertainty (2 sigma +/- 30%). The results confirm the growing importance of s-WEEE regarding secondary resource metals and potential toxic substances. Nowadays, the thirty times smaller s-WEEE turns over larger flows for many substances, compared to municipal solid waste. Transfer coefficient results serve to evaluate the separation efficiency of the recycling process and confirm--with the exception of PCB and Hg--the limitation of hand-sorting and mechanical processing to separate pollutants (Cd, Pb, etc.) out of reusable fractions. Regularly applied SFA would serve to assess the efficacy of legislative, organizational and technical measures on the WEEE.

  18. Hydrochemical processes in mine waste deposits and drainage water - Heavy metal speciation, sorption and sedimentation processes

    Energy Technology Data Exchange (ETDEWEB)

    Loevgren, L.; Sjoeberg, S. [Umeaa Univ. (Sweden). Dept. of Inorganic Chemistry

    1997-12-31

    The aim of the present project has been to quantitatively describe hydrochemical processes relevant for the retention and mobility of heavy metals in mine waste deposits. The activities have been focused on the solubility and speciation of Pb(II), Cd(II), Cu(II), Zn(II), CR(VI) and As(III,V). Main attention has been paid to adsorption processes at the surfaces of iron (hydr)oxides (goethite, et-FeOOH). The main experimental methods for studying the adsorption reactions have been potentiometric titrations and batch adsorption experiments. Experimental data have been evaluated in terms of models for surface complexation equilibria, which can be used in hydrogeochemical model calculations of processes within the deposits as well as in the recipients of drainage water. Furthermore, in several cases the surface complexes formed have been characterized structurally by means of Fourier Transform-Infrared spectroscopy. In order to test the validity of the equilibrium models obtained at millimolar concentrations of both sorbate and sorbent a new method utilizing Anodic Stripping Voltammetry as an in situ probe in titrations has been developed within the project. A particular interest has been given to the influence of complexing inorganic and organic anions on the adsorption of the heavy metal ions. The presence of sulfate ions resulted in a moderate increased adsorption of Cu(II) and Pb(II) under acidic conditions, while the adsorption of Zn(II) remained uninfluenced. The increased adsorption could be explained by reduced electrostatic repulsion between positively charged surfaces and metal ions, and by formation of ternary surface complexes. Similar mechanisms could explain the data in the goethite-Me(II)- carboxylate systems. The organic acids study are: phthalic acid, trimellitic acid and pyromellitic acid, which are aromatic acids with two, three and four carboxylate groups, respectively. Before the experimental data in the organic containing systems could be

  19. Two-Dimensional Layered Double Hydroxide Derived from Vermiculite Waste Water Supported Highly Dispersed Ni Nanoparticles for CO Methanation

    Directory of Open Access Journals (Sweden)

    Panpan Li

    2017-03-01

    Full Text Available Expanded multilayered vermiculite (VMT was successfully used as catalyst support and Ni/VMT synthesized by microwave irradiation assisted synthesis (MIAS exhibited excellent performance in our previous work. We also developed a two-dimensional porous SiO2 nanomesh (2D VMT-SiO2 by mixed-acid etching of VMT. Compared with three-dimensional (3D MCM-41, 2D VMT-SiO2 as a catalyst support provided a superior position for implantation of NiO species and the as-obtained catalyst exhibited excellent performance. In this paper, we successfully synthesized a layered double hydroxide (LDH using the spent liquor after mixed-acid etching of VMT, which mainly contained Mg2+ and Al3+. The as-calcined layered double oxide (LDO was used as a catalyst support for CO methanation. Compared with Ni/MgAl-LDO, Ni/VMT-LDO had smaller active component particles; therefore, in this study, it exhibited excellent catalytic performance over the whole temperature range of 250–500 °C. Ni/VMT-LDO achieved the best activity with 87.88% CO conversion, 89.97% CH4 selectivity, and 12.47 × 10−2·s−1 turn over frequency (TOF at 400 °C under a gas hourly space velocity of 20,000 mL/g/h. This study demonstrated that VMT-LDO as a catalyst support provided an efficient way to develop high-performance catalysts for synthetic natural gas (SNG from syngas.

  20. Children with health impairments by heavy metals in an e-waste recycling area

    NARCIS (Netherlands)

    Zeng, Xiang; Xu, Xijin; Boezen, H. Marike; Huo, Xia

    E-waste recycling has become a global environmental health issue. Pernicious chemicals escape into the environment due to informal and nonstandard e-waste recycling activities involving manual dismantling, open burning to recover heavy metals and open dumping of residual fractions. Heavy metals

  1. 40 CFR 60.52a - Standard for municipal waste combustor metals.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 6 2010-07-01 2010-07-01 false Standard for municipal waste combustor metals. 60.52a Section 60.52a Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... September 20, 1994 § 60.52a Standard for municipal waste combustor metals. (a) On and after the date on...

  2. Continuous Process for Biodiesel Production in Packed Bed Reactor from Waste Frying Oil Using Potassium Hydroxide Supported on Jatropha curcas Fruit Shell as Solid Catalyst

    Directory of Open Access Journals (Sweden)

    Achanai Buasri

    2012-08-01

    Full Text Available The transesterification of waste frying oil (WFO with methanol in the presence of potassium hydroxide catalyst supported on Jatropha curcas fruit shell activated carbon (KOH/JS was studied. The catalyst systems were characterized by X-ray diffraction (XRD, scanning electron microscopy (SEM and the Brunauer–Emmett–Teller (BET method. The effects of reaction variables such as residence time, reaction temperature, methanol/oil molar ratio and catalyst bed height in packed bed reactor (PBR on the yield of biodiesel were investigated. SEM images showed that KOH was well distributed on the catalyst support. The optimum conditions for achieving the conversion yield of 86.7% consisted of a residence time of 2 h, reaction temperature of 60 °C, methanol/oil molar ratio of 16 and catalyst bed height of 250 mm. KOH/JS could be used repeatedly five times without any activation treatment, and no significant activity loss was observed. The results confirmed that KOH/JS catalyst had a great potential to be used for industrial application in the transesterification of WFO. The fuel properties of biodiesel were also determined.

  3. Immobilization of metal wastes by reaction with H2S in anoxic basins: concept and elaboration.

    Science.gov (United States)

    Schuiling, R D

    2013-10-01

    Metal wastes are produced in large quantities by a number of industries. Their disposal in isolated waste deposits is certain to cause many subsequent problems, because every material will sooner or later return to the geochemical cycle. The sealing of disposal sites usually starts to leak, often within a short time after the disposal site has been filled. The contained heavy metals are leached from the waste deposit and will contaminate the soil and the groundwater. It is evident that storage as metal sulfides in a permanently anoxic environment is the only safe way to handle metal wastes. The world's largest anoxic basin, the Black Sea, can serve as a georeactor. The metal wastes are sustainably transformed into harmless and immobile solids. These are incorporated in the lifeless bottom muds, where they are stored for millions of years.

  4. Waste Metal For Improving Concrete Performance And Utilisation As An Alternative Of Reinforcement Bar

    OpenAIRE

    Tanvir Qureshi; Mustaq Ahmed

    2015-01-01

    Waste material disposal is considered as a difficult issue to adopt in current world. Waste metal, which has been recognised as a major problem in the environment and resource deficiency, could have important implications in the concrete construction industries. Waste metal utilisation in construction of reinforced cement concrete (RCC) works is immerging in recent time. Construction industries are looking for cost effective structural materials and utilisation of renewable materi...

  5. Release to the gas phase of metals, S and Cl during combustion of dedicated waste fractions

    DEFF Research Database (Denmark)

    Pedersen, Anne Juul; van Lith, Simone Cornelia; Frandsen, Flemming

    2010-01-01

    wood, shoes, automotive shredder waste and PVC (poly-vinyl-chloride). The waste fractions were characterized by use of wet chemical analysis, and, based on the chemical composition of the initial fuel sample and the ash residue after the experiments; the release of inorganic elements was quantified......The release to the gas phase of inorganic elements such as alkali metals. Cl, S, and heavy metals in Waste-to-Energy (WtE) boilers is a challenge. Besides the risk of harmful emissions to the environment, inorganic elements released from the grate may cause severe ash deposition and corrosion...... and the link to the formation of fly ash and aerosols in full-scale waste incinerators. The release of metals, S and Cl from four dedicated waste fractions was quantified as a function of temperature in a lab-scale fixed-bed reactor. The waste fractions comprised chromated copper arsenate (CCA) impregnated...

  6. Thermal Analysis and Flame-Retarded Mechanism of Composites Composed of Ethylene Vinyl Acetate and Layered Double Hydroxides Containing Transition Metals (Mn, Co, Cu, Zn

    Directory of Open Access Journals (Sweden)

    Lili Wang

    2016-05-01

    Full Text Available The effects of transition metals on the hydrophobicity of nano–structured layered double hydroxides (LDHs and the compatibility of LDHs/ethylene vinyl acetate (EVA composites have seldom been reported. NiMgAl–LDHs slightly surface–modified with stearate and doped with transition metal cations (Mn2+, Co2+, Cu2+, Zn2+ are investigated. Compared to the pure EVA, not only were the maximal degradation–rate temperatures (Tmax of the ethylene–based chains enhanced, but also the smoke production rate (SPR and the production rate of CO (COP were sharply decreased for all the composites. Most importantly, a new flame retardant mechanism was found, namely the peak heat release rate (pk-HRR time, which directly depends on the peak production rate of CO2 (pk-CO2 time for EVA and all composites by cone calorimeter test. Moreover, the Mn–doped LDH S–NiMgAl–Mn shows more uniform dispersion and better interfacial compatibility in the EVA matrix. The cone calorimetric residue of S–NiMgAl–Mn/EVA has the intumescent char layer and the compact metal oxide layer. Therefore, S–NiMgAl–Mn/EVA shows the lowest pk-HRR and the longest pk-HRR time among all the composites.

  7. Urinary heavy metal levels and relevant factors among people exposed to e-waste dismantling.

    Science.gov (United States)

    Wang, Hongmei; Han, Mei; Yang, Suwen; Chen, Yanqing; Liu, Qian; Ke, Shen

    2011-01-01

    Primitive electronic waste (e-waste) recycling has become a growing environmental concern, and toxic heavy metals released from e-waste activities may continue to threaten the health of local people. To study the impact of heavy metals in people around e-waste sites, 349 people from e-waste recycling sites (exposure group) and 118 people from a green plantation (control group) were surveyed, and their urinary levels of lead (UPb), cadmium (UCd), manganese (UMn), copper (UCu), and Zinc (UZn) were assayed. Questionnaire surveys for risk factors were also performed and analyzed by using the Pearson correlation analysis. Results indicated that the levels of urinary Cd in both occupational dismantling people {GM(GSD) 0.72(0.71) ug/L} and non-occupational dismantling people {GM(GSD) 0.50(0.79) ug/L} were higher than the control group {GM(GSD) 0.27(0.85) ug/L}. Further analyses of correlations between urinary heavy metal levels and exposure factors in the exposed group revealed positive relationship between the duration of dismantling and the level of UPb (p metal burden, and not all urinary heavy metal levels can be contributed to e-waste dismantling exposure levels. Primitive e-waste recycling activities may contribute to the changes of urinary heavy metal levels and increase the health risk for those chronically working on e-waste dismantling. Copyright © 2010 Elsevier Ltd. All rights reserved.

  8. Analysis of the application of decontamination technologies to radioactive metal waste minimization using expert systems

    Energy Technology Data Exchange (ETDEWEB)

    Bayrakal, Suna [Iowa State Univ., Ames, IA (United States)

    1993-09-30

    Radioactive metal waste makes up a significant portion of the waste currently being sent for disposal. Recovery of this metal as a valuable resource is possible through the use of decontamination technologies. Through the development and use of expert systems a comparison can be made of laser decontamination, a technology currently under development at Ames Laboratory, with currently available decontamination technologies for applicability to the types of metal waste being generated and the effectiveness of these versus simply disposing of the waste. These technologies can be technically and economically evaluated by the use of expert systems techniques to provide a waste management decision making tool that generates, given an identified metal waste, waste management recommendations. The user enters waste characteristic information as input and the system then recommends decontamination technologies, determines residual contamination levels and possible waste management strategies, carries out a cost analysis and then ranks, according to cost, the possibilities for management of the waste. The expert system was developed using information from literature and personnel experienced in the use of decontamination technologies and requires validation by human experts and assignment of confidence factors to the knowledge represented within.

  9. Recovery of metals and nonmetals from electronic waste by physical and chemical recycling processes.

    Science.gov (United States)

    Kaya, Muammer

    2016-11-01

    This paper reviews the existing and state of art knowledge for electronic waste (e-waste) recycling. Electrical and/or electronic devices which are unwanted, broken or discarded by their original users are known as e-waste. The main purpose of this article is to provide a comprehensive review of e-waste problem, strategies of e-waste management and various physical, chemical and metallurgical e-waste recycling processes, their advantages and disadvantages towards achieving a cleaner process of waste utilization, with special attention towards extraction of both metallic values and nonmetallic substances. The hazards arise from the presence of heavy metals Hg, Cd, Pb, etc., brominated flame retardants (BFRs) and other potentially harmful substances in e-waste. Due to the presence of these substances, e-waste is generally considered as hazardous waste and, if improperly managed, may pose significant human and environmental health risks. This review describes the potential hazards and economic opportunities of e-waste. Firstly, an overview of e-waste/printed circuit board (PCB) components is given. Current status and future perspectives of e-waste/PCB recycling are described. E-waste characterization, dismantling methods, liberation and classification processes are also covered. Manual selective dismantling after desoldering and metal-nonmetal liberation at -150μm with two step crushing are seen to be the best techniques. After size reduction, mainly physical separation processes employing gravity, electrostatic, magnetic separators, froth floatation, etc. have been critically reviewed here for separation of metals and nonmetals, along with useful utilizations of the nonmetallic materials. The recovery of metals from e-waste material after physical separation through pyrometallurgical, hydrometallurgical or biohydrometallurgical routes is also discussed along with purification and refining. Suitable PCB recycling flowsheets for industrial applications are also given

  10. The effect of waste water treatment on river metal concentrations: removal or enrichment?

    NARCIS (Netherlands)

    Teuchies, J.; Bervoets, L.; Cox, T.J.S.; Meire, P.; de Deckere, E.

    2011-01-01

    Purpose Discharge of untreated domestic and industrial waste in many European rivers resulted in low oxygen concentrations and contamination with trace metals, often concentrated in sediments. Under these anoxic conditions, the formation of insoluble metal sulfides is known to reduce metal

  11. Desulphurization of hot metal and nickel pig iron using waste materials from the aluminum industry

    Energy Technology Data Exchange (ETDEWEB)

    Yang, Y.D.; McLean, A. [Toronto Univ., ON (Canada). Dept. of Materials Science and Engineering; Hasegawa, M.; Iwase, M. [Kyoto Univ., Kyoto (Japan). Dept. of Energy Science and Technology, Ferrous Metallurgy Research Group; Ren, M.L.; Zhang, D.F. [China Aluminum Co. Ltd., Shandong (China)

    2009-07-01

    The aluminium and steel industries are both energy-intensive and have significant impacts on the environment. The desulphurization of hot metal and nickel pig iron using waste materials from the aluminium industry was evaluated in this study. A simple processing technique using dross and white mud was developed to desulphurize hot metals. Waste materials with a high oxide content were combined with an aluminium instant reduction method and then used for hot metal desulphurization. The presence of nickel in the hot metals showed a negative effect on the desulphurization process as the nickel reduced carbon solubility in an iron-based metal solution. It was concluded that the use of waste slags and solids residuals from the aluminium industry within the steel industry will reduce the disposal of waste and provide significant economic benefits to both industries. 6 refs., 2 tabs., 12 figs.

  12. Evaluation of heavy metals in the process of composting organic waste of coca leaves

    Directory of Open Access Journals (Sweden)

    Apaza-Condori Emma Eva

    2015-11-01

    Full Text Available The present study is to evaluate the total concentrations of the heavy metals in waste compost samples from coca leaf. This work was carried out Kallutaca Experimental Center, Biofertilizers module Career Agricultural Engineering at the Public University of El Alto, La Paz municipality of Laja. Posed treatments were: T1 (+ Yogurt Coca wastes; T2 (Coca wastes + whey; T3 (Coca wastes + yeast and T4 (Control. The design was completely randomized with 4 treatments and 3 repetitions. The concentration of heavy metals (cadmium, copper, nickel, lead, mercury and chromium; they were categorized into Class A, for the four treatments according to the classifications established by Moreno & Moral (2008.

  13. Lixiviation of heavy metals of hazardous industrial wastes by means of thermostatized columns and design of a pilot plant; Lixiviacion de metales pesados de residuos industriales peligrosos por medio de columnas termostatizadas y diseno de una planta piloto

    Energy Technology Data Exchange (ETDEWEB)

    Vite T, J.; Leon, C.C. de [ININ, 52045 Ocoyoacac, Estado de Mexico (Mexico); Vite T, M.; Soto T, J.L. [IPN, SEPI, ESIME 07738 Mexico D.F. (Mexico)]. e-mail: jvite@nuclear.inin.mx

    2006-07-01

    purpose of this work was to evaluate the efficiency of lixiviation of heavy metals, using thermostatized columns and hazardous industrial residual wastes: those by the volume with which are generated and its high toxicity, its represent a great problem for it treatment and disposition, in this work a diagram of a pilot plant for extraction of heavy metals is included. The process and equipment were patented in United States and in Mexico. For the development of this study four thermostated columns were used that were coupled. The waste were finely milled and suspended in an aqueous pulp adding of 10 - 40gL{sup -1} of mineral acid or sodium hydroxide until reaching an interval of pH of 2,5,7 and 10. Its were used of 4-10 gL{sup -1} of a reducer agent and of 0.3-1.5 g of a surfactant agent. In some cases with this method was possible to remove until 100% of heavy metals. It was used Plasma Emission Spectroscopy to determine the concentrations of the cations in the lixiviation liquors. For studying the metallic alloys the X-ray diffraction technique was used. (Author)

  14. Monodisperse embedded nanoparticles derived from an atomic metal-dispersed precursor of layered double hydroxide for architectured carbon nanotube formation

    DEFF Research Database (Denmark)

    Tian, Gui-Li; Zhao, Meng-Qiang; Zhang, Bingsen

    2014-01-01

    Monodisperse metal nanoparticles (NPs) with high activity and selectivity are among the most important catalytic materials. However, the intrinsic process to obtain well-dispersed metal NPs with tunable high density (ranging from 10(13) to 10(16) m(-2)) and thermal stability is not yet well under...

  15. Metal Extraction Processes for Electronic Waste and Existing Industrial Routes: A Review and Australian Perspective

    Directory of Open Access Journals (Sweden)

    Abdul Khaliq

    2014-02-01

    Full Text Available The useful life of electrical and electronic equipment (EEE has been shortened as a consequence of the advancement in technology and change in consumer patterns. This has resulted in the generation of large quantities of electronic waste (e-waste that needs to be managed. The handling of e-waste including combustion in incinerators, disposing in landfill or exporting overseas is no longer permitted due to environmental pollution and global legislations. Additionally, the presence of precious metals (PMs makes e-waste recycling attractive economically. In this paper, current metallurgical processes for the extraction of metals from e-waste, including existing industrial routes, are reviewed. In the first part of this paper, the definition, composition and classifications of e-wastes are described. In the second part, separation of metals from e-waste using mechanical processing, hydrometallurgical and pyrometallurgical routes are critically analyzed. Pyrometallurgical routes are comparatively economical and eco-efficient if the hazardous emissions are controlled. Currently, pyrometallurgical routes are used initially for the segregation and upgrading of PMs (gold and silver into base metals (BMs (copper, lead and nickel and followed by hydrometallurgical and electrometallurgical processing for the recovery of pure base and PMs. For the recycling of e-waste in Australia, challenges such as collection, transportation, liberation of metal fractions, and installation of integrated smelting and refining facilities are identified.

  16. Mining Waste Classification and Quantity of Non-Metal Minesin Slovenia

    Directory of Open Access Journals (Sweden)

    Ana Burger

    2007-06-01

    Full Text Available Mining is an important human activity that creates wealth and supplies materials for maintaining standard of living and further human development. However, mining has also negative impacts on the environment and society. One of them is the production of mining waste throughout the entire mining cycle, in particular in the mine development and operation /production stage.Due to the EU Directive 2006/21/EC on the management of waste from the extractive industries and its implementation in Member state, estimation on quality and quantity of mining waste from active non-metal mines in Slovenia was carried out. In the selected mines mining and processing was closely examined. With material flow analysis quantity and characteristics of mining waste were defined for several mines of different commodities.Data on mining waste were afterwards generalized in order to get an overall country evaluation on mining waste “production” of non-metal mines.Mining waste as a result of mining and beneficiation processes in non-metal mines of Slovenia is either inert or non-hazardous. Most of the mining waste is used for mine reclamation running simultaneously with the production phase. The largest amounts of mining waste per unit produced are created in dimension stone industry. Since the dimensionstone production is small, the waste amount is negligible. Large quantities of mining waste are produced in crushed stone and, sand and gravel operations, because aggregate production is pretty large with regard to other non-metals production in Slovenia. We can therefore conclude that large quantities of mining waste from non-metal mines, which are mostly used in reclamation and for side products, do not represent danger to the environment.

  17. An overview of metals recovery from thermal power plant solid wastes.

    Science.gov (United States)

    Meawad, Amr S; Bojinova, Darinka Y; Pelovski, Yoncho G

    2010-12-01

    Thermal power plants (TPPs) that burn fossil fuels emit several pollutants linked to the environmental problems of acid rain, urban ozone, and the possibility of global climate change. As coal is burned in a power plant, its noncombustible mineral content is partitioned into bottom ash, which remains in the furnace, and fly ash, which rises with flue gases. Two other by-products of coal combustion air-pollution control technologies are flue gas desulfurization (FGD) wastes and fluidized-bed combustion (FBC) wastes. This paper analyzed and summarized the generation, characteristics and application of TPP solid wastes and discussed the potential effects of such solid wastes on the environment. On this basis, a review of a number of methods for recovery of metals from TPP solid wastes was made. They usually contain a quantity of valuable metals and they are actually a secondary resource of metals. By applying mineral processing technologies and hydrometallurgical and biohydrometallurgical processes, it is possible to recover metals such as Al, Ga, Ge, Ca, Cd, Fe, Hg, Mg, Na, Ni, Pb, Ra, Th, V, Zn, etc., from TPP solid wastes. Recovery of metals from such wastes and its utilization are important not only for saving metal resources, but also for protecting the environment. Copyright © 2010 Elsevier Ltd. All rights reserved.

  18. Design of an innovative, ecological portable waste compressor for in-house recycling of paper, plastic and metal packaging waste.

    Science.gov (United States)

    Xevgenos, D; Athanasopoulos, N; Kostazos, P K; Manolakos, D E; Moustakas, K; Malamis, D; Loizidou, M

    2015-05-01

    Waste management in Greece relies heavily on unsustainable waste practices (mainly landfills and in certain cases uncontrolled dumping of untreated waste). Even though major improvements have been achieved in the recycling of municipal solid waste during recent years, there are some barriers that hinder the achievement of high recycling rates. Source separation of municipal solid waste has been recognised as a promising solution to produce high-quality recycled materials that can be easily directed to secondary materials markets. This article presents an innovative miniature waste separator/compressor that has been designed and developed for the source separation of municipal solid waste at a household level. The design of the system is in line with the Waste Framework Directive (2008/98/EC), since it allows for the separate collection (and compression) of municipal solid waste, namely: plastic (polyethylene terephthalate and high-density polyethylene), paper (cardboard and Tetrapak) and metal (aluminium and tin cans). It has been designed through the use of suitable software tools (LS-DYNA, INVENTROR and COMSOL). The results from the simulations, as well as the whole design process and philosophy, are discussed in this article. © The Author(s) 2015.

  19. Recovery of precious metals from industrial wastes using membrane separation

    Energy Technology Data Exchange (ETDEWEB)

    Jeong, Jin Ki; Lee, Jae Chun; Youn, In Ju [Korea Inst. of Geology Mining and Materials, Taejon (Korea, Republic of)

    1995-12-01

    The purpose of the research is to develop a membrane technology for the recovery of Au by the concentration of used cyanide solution. Au and Ag have been widely used in various advanced technology due to their excellent physical and chemical properties. In most of their application, they were electrodeposited in the cyanide solution. The solution was also used as an etchant for the decorative gold alloys such as 14 K and 18 K. Due to the expanding related industry, the amount of used cyanide solution has been greatly increased. The used solution normally contains about 1-3 g/1 of Au. Due to their high prices various separation method has been developed and commercialized for long time. The concentration method which removes water offers various advantages like the reduction of used solution, the needless of additional cyanide, and the increase in the recovery rate. The main objective of the study was laid in the development of an economical recovery process for precious metals including Au from used cyanide solution. To achieve this goal related processes were reviewed comprehensively focussing on the membrane process and the concentration process. The feasibility of membrane process was evaluated by the measurement of separation efficiency and concentration efficiency of cyanide. In addition, various CN analysis was compared in order to develop a simple and routine procedure for future experiment. The process does not require additional cyanide and thus prevents further environmental contamination. It is economical because the recovery can be increased by the concentration of the solution during the recovery process. In addition, it can be applied to other metals waste system due to the reduced recovery process by concentration. The used water can also be reused. (author). 23 refs., 16 figs., 5 tabs.

  20. The study of heavy metals leaching from waste foundry sands using a one-step extraction

    Directory of Open Access Journals (Sweden)

    Bożym Marta

    2017-01-01

    Full Text Available There are a number of leaching test which are used to evaluate the effect of foundry waste disposal on the environment (TCLP, SPLP, ASTM at al.. Because the spent foundry sand are usually deposited at the ground level and they have a similar structure to the soil, survey mobility of metals using the same methods seems appropriate. One-step extraction allows for the evaluation of the mobility and bioavailability of metals in soil and waste. Waste foundry sands have been successfully used as a component in manufactured soils in U.S., but concern over metal contamination must be eliminated before considering this direction of use. The study evaluated the leaching of heavy metals (Cd, Pb, Cu, Zn, Cr, Ni from deposited waste foundry sands. The overall, as well as heavy metals were extracted by different type of extractants: H2O, CH3COOH, HCl, EDTA, MgCl2 and NaCOOH. These extractants are most commonly used to study the mobility and bioavailability of metals in soil and waste. In the present study applicable standards and methodology described in the literature in analysis were used. The results allowed to evaluate the bioavailability of metals leached from those wastes.

  1. The study of heavy metals leaching from waste foundry sands using a one-step extraction

    Science.gov (United States)

    Bożym, Marta

    2017-10-01

    There are a number of leaching test which are used to evaluate the effect of foundry waste disposal on the environment (TCLP, SPLP, ASTM at al.). Because the spent foundry sand are usually deposited at the ground level and they have a similar structure to the soil, survey mobility of metals using the same methods seems appropriate. One-step extraction allows for the evaluation of the mobility and bioavailability of metals in soil and waste. Waste foundry sands have been successfully used as a component in manufactured soils in U.S., but concern over metal contamination must be eliminated before considering this direction of use. The study evaluated the leaching of heavy metals (Cd, Pb, Cu, Zn, Cr, Ni) from deposited waste foundry sands. The overall, as well as heavy metals were extracted by different type of extractants: H2O, CH3COOH, HCl, EDTA, MgCl2 and NaCOOH. These extractants are most commonly used to study the mobility and bioavailability of metals in soil and waste. In the present study applicable standards and methodology described in the literature in analysis were used. The results allowed to evaluate the bioavailability of metals leached from those wastes.

  2. Safety evaluation of the leaching of metals from the printed graphic product wastes

    Directory of Open Access Journals (Sweden)

    Savka Adamović

    2015-09-01

    Full Text Available Due to the technological development of the graphic production, the environment is being faced with a large amount of printed graphic product wastes, especially packaging materials (paper, cardboard, paper and plastic bags, films, etc, but it is also being faced with the problem of their disposal. Many printing inks and coatings used in the production of the printed graphic product contain metals which, after the disposal of graphic waste, can migrate to different systems and have a negative influence on the environment. Because of that, the concentration levels of metals (zinc, copper, chromium, cadmium, lead, and nickel in the printed graphic product wastes have firstly been determined, and then the impact of those metals, through their migration from the printed graphic product wastes to the simulated environmental mediums with different pH values (acidic and neutral, has been estimated. Based on the experimentally obtained concentrations of metals that have migrated from the printed graphic product wastes to the neutral solution and based on the theoretical distribution coefficient, the concentration of metals in the soil of illegal and municipal landfills, which represents the contribution to the overall metal concentration in the soil due to the migration from the waste printed graphic materials, has been calculated. Also, a comparison between the experimentally obtained metal concentrations and the literature values has been conducted, and an evaluation of their influence on the quality of soil has been given.

  3. Removal and recovery of toxic metal ions from aqueous waste sites using polymer pendant ligands

    Energy Technology Data Exchange (ETDEWEB)

    Fish, D. [Lawrence Berkeley National Lab., CA (United States)

    1996-10-01

    The purpose of this project is to investigate the use of polymer pendant ligand technology to remove and recover toxic metal ions from DOE aqueous waste sites. Polymer pendant lgiands are organic ligands, anchored to crosslinked, modified divinylbenzene-polystyrene beads, that can selectively complex metal ions. The metal ion removal step usually occurs through a complexation or ion exchange phenomena, thus recovery of the metal ions and reuse of the beads is readily accomplished.

  4. Wear Behavior of Aluminium Metal Matrix Composite Prepared from Industrial Waste

    National Research Council Canada - National Science Library

    Xavier, L Francis; Suresh, Paramasivam

    2016-01-01

    .... In this work, Aluminium Metal Matrix Composite is prepared by reinforcing 10 wt% and 20 wt% of wet grinder stone dust particles an industrial waste obtained during processing of quarry rocks which are available in nature...

  5. Waste printing paper as analogous adsorbents for heavy metals in ...

    African Journals Online (AJOL)

    user

    Waste printing paper (WPP) is an abundant local waste material that requires end-use channelling to ... alternative channel for waste paper use is underexplored. ..... Separation and. Purification. Technology, 57 (2007) 126. 16. Vieira, R.H and Volesky, B.,. International, 3 (2000) 17. 17. Rao, M. and Parwate, A.V. journal of.

  6. Immobilization of metal wastes by reaction with H2S in anoxic basins. Concept and Elaboration

    NARCIS (Netherlands)

    Schuiling, R.D.

    2013-01-01

    Metal wastes are produced in large quantities by a number of industries. Their disposal in isolated waste deposits is certain to cause many subsequent problems, because every material will sooner or later return to the geochemical cycle. The sealing of disposal sites usually starts to

  7. Kinetic vaporization of heavy metals during fluidized bed thermal treatment of municipal solid waste.

    Science.gov (United States)

    Yu, Jie; Sun, Lushi; Xiang, Jun; Hu, Song; Su, Sheng

    2013-02-01

    Heavy metals volatilization during thermal treatment of model solid waste was theoretically and experimentally investigated in a fluidized bed reactor. Lead, cadmium, zinc and copper, the most four conventional heavy metals were investigated. Particle temperature model and metal diffusion model were established to simulate the volatilization of CdCl(2) evaporation and investigate the possible influencing factors. The diffusion coefficient, porosity and particle size had significant effects on metal volatilization. The higher diffusion coefficient and porosity resulted in the higher metal evaporation. The influence of redox conditions, HCl, water and mineral matrice were also investigated experimentally. The metal volatilization can be promoted by the injection of HCl, while oxygen played a negative role. The diffusion process of heavy metals within particles also had a significant influence on kinetics of their vaporization. The interaction between heavy metals and mineral matter can decrease metal evaporation amount by forming stable metallic species. Copyright © 2012 Elsevier Ltd. All rights reserved.

  8. Charging and ion adsorption behaviour of different iron (hydr)oxides

    NARCIS (Netherlands)

    Venema, P.

    1997-01-01

    Metal (hydr)oxides are of importance for many soil systems. All metal (hydr)oxides have a surface charge that varies with the pH. The variation in this surface charge is caused by adsorption and desorption of protons. The adsorption of cat- and anions on the metal (hydr)oxide surface is

  9. Generation of copper rich metallic phases from waste printed circuit boards

    Energy Technology Data Exchange (ETDEWEB)

    Cayumil, R. [Centre for Sustainable Materials Research and Technology (SMaRT), School of Materials Science and Engineering, The University of New South Wales, Sydney, NSW 2052 (Australia); Khanna, R., E-mail: ritakhanna@unsw.edu.au [Centre for Sustainable Materials Research and Technology (SMaRT), School of Materials Science and Engineering, The University of New South Wales, Sydney, NSW 2052 (Australia); Ikram-Ul-Haq, M.; Rajarao, R. [Centre for Sustainable Materials Research and Technology (SMaRT), School of Materials Science and Engineering, The University of New South Wales, Sydney, NSW 2052 (Australia); Hill, A. [CSIRO Process Science and Engineering, Clayton, Melbourne, VIC 3168 (Australia); Sahajwalla, V. [Centre for Sustainable Materials Research and Technology (SMaRT), School of Materials Science and Engineering, The University of New South Wales, Sydney, NSW 2052 (Australia)

    2014-10-15

    Highlights: • Recycling and material recovery from waste printed circuit boards is very complex. • Thermoset polymers, ceramics and metals are present simultaneously in waste PCBs. • Heat treatment of PCBs was carried out at 1150 °C under inert conditions. • Various metallic phases could be segregated out as copper based metallic droplets. • Carbon and ceramics residues can be further recycled in a range of applications. - Abstract: The rapid consumption and obsolescence of electronics have resulted in e-waste being one of the fastest growing waste streams worldwide. Printed circuit boards (PCBs) are among the most complex e-waste, containing significant quantities of hazardous and toxic materials leading to high levels of pollution if landfilled or processed inappropriately. However, PCBs are also an important resource of metals including copper, tin, lead and precious metals; their recycling is appealing especially as the concentration of these metals in PCBs is considerably higher than in their ores. This article is focused on a novel approach to recover copper rich phases from waste PCBs. Crushed PCBs were heat treated at 1150 °C under argon gas flowing at 1 L/min into a horizontal tube furnace. Samples were placed into an alumina crucible and positioned in the cold zone of the furnace for 5 min to avoid thermal shock, and then pushed into the hot zone, with specimens exposed to high temperatures for 10 and 20 min. After treatment, residues were pulled back to the cold zone and kept there for 5 min to avoid thermal cracking and re-oxidation. This process resulted in the generation of a metallic phase in the form of droplets and a carbonaceous residue. The metallic phase was formed of copper-rich red droplets and tin-rich white droplets along with the presence of several precious metals. The carbonaceous residue was found to consist of slag and ∼30% carbon. The process conditions led to the segregation of hazardous lead and tin clusters in the

  10. A study of transformation water - soluble forms of hevy metals at waste incenerator for detoxicationof ash.

    Directory of Open Access Journals (Sweden)

    Bilets'ka V. А.

    2011-11-01

    Full Text Available The complex research processes of transformation of soluble forms of heavy metals in sediment interaction with ash. Proved that the adsorption processes of immobilization lead to a significant decrease of soluble forms of heavy metals in the waste.

  11. Characterization of Irradiated Metal Waste from the Pyrometallurgical Treatment of Used EBR-II Fuel

    Energy Technology Data Exchange (ETDEWEB)

    B.R. Westphal; K.C. Marsden; W.M. McCartin; S.M. Frank; D.D. Keiser, Jr.; T.S. Yoo; D. Vaden; D.G. Cummings; K.J. Bateman; J. J. Giglio; T. P. O' Holleran; P. A. Hahn; M. N. Patterson

    2013-03-01

    As part of the pyrometallurgical treatment of used Experimental Breeder Reactor-II fuel, a metal waste stream is generated consisting primarily of cladding hulls laden with fission products noble to the electrorefining process. Consolidation by melting at high temperature [1873 K (1600 degrees C)] has been developed to sequester the noble metal fission products (Zr, Mo, Tc, Ru, Rh, Te, and Pd) which remain in the iron-based cladding hulls. Zirconium from the uranium fuel alloy (U-10Zr) is also deposited on the hulls and forms Fe-Zr intermetallics which incorporate the noble metals as well as residual actinides during processing. Hence, Zr has been chosen as the primary indicator for consistency of the metal waste. Recently, the first production-scale metal waste ingot was generated and sampled to monitor Zr content for Fe-Zr intermetallic phase formation and validation of processing conditions. Chemical assay of the metal waste ingot revealed a homogeneous distribution of the noble metal fission products as well as the primary fuel constituents U and Zr. Microstructural characterization of the ingot confirmed the immobilization of the noble metals in the Fe-Zr intermetallic phase.

  12. Investigation of the dye-sensitized solar cell designed by a series of mixed metal oxides based on ZnAl-layered double hydroxide

    Science.gov (United States)

    Zhu, Yatong; Wang, Dali; Yang, Xiaoyu; Liu, Sha; Liu, Dong; Liu, Jie; Xiao, Hongdi; Hao, Xiaotao; Liu, Jianqiang

    2017-10-01

    In this paper, the anode materials for dye-sensitized solar cell (DSSC) were prepared by a facile calcination method using the ZnAl-layered double hydroxide (LDH) as a precursor. The ZnAl-LDHs with different molar ratios (Zn:Al = 2, 4, 6, 8) were prepared by the urea method and the mixed metal oxides (MMO) were prepared by calcining the LDHs at 500 °C. A series of cells were assembled by the corresponding MMOs and different dyes (N3 and N719). The basic parameters were investigated by X-ray diffraction, scanning electron microscope, thermogravimetric and differential thermal analysis, nitrogen sorption analysis and UV-Vis absorption spectrum. The photovoltaic performance of DSSCs was measured by electrochemical method. It could be seen that ZnAl molar ratios and different dyes had great influence on the efficiency of DSSC. The efficiency improved explicitly with increasing ZnAl molar ratio and the DSSC made of N3 showed better efficiency than that of N719. The best efficiency of N3 conditions reached 0.55% when the ratio of ZnAl-LDH precursor was 8:1.

  13. An assessment on the recycling opportunities of wastes emanating from scrap metal processing in Mauritius.

    Science.gov (United States)

    Mauthoor, Sumayya; Mohee, Romeela; Kowlesser, Prakash

    2014-10-01

    This paper presents an assessment on the wastes namely slag, dust, mill scale and sludge resulting from scrap metal processing. The aim of this study is to demonstrate that there are various ways via which scrap metal processing wastes can be reused or recycled in other applications instead of simply diverting them to the landfill. These wastes are briefly described and an overview on the different areas of applications is presented. Based on the results obtained, the waste generation factor developed was 349.3 kg per ton of steel produced and it was reported that slag represents 72% of the total wastes emanating from the iron and steel industry in Mauritius. Finally the suitability of the different treatment and valorisation options in the context of Mauritius is examined. Copyright © 2013 Elsevier Ltd. All rights reserved.

  14. ECLSS Universal Waste Management System (UWMS) Metal Materials Compatibility Study- Electrochemical and Crevice Corrosion Evaluation

    Science.gov (United States)

    Lee, R. E.

    2017-01-01

    Electrochemical and crevice corrosion laboratory test results are presented for three noble metal candidates with possible application on the Universal Waste Management System (UWMS) in support of the Environmental Control and Life Support System (ECLSS) aboard the International Space Station (ISS). The three metal candidates, which included Inconel 625, Hastelloy C276 and Titanium 6Al-4V, were evaluated in two solutions representative of the acidic pretreatment formulations utilized during processing of waste liquids within the ECLSS. Final test results and data analysis indicated that the passive layer on all three metals provides excellent corrosion protection in both solutions under standard test conditions.

  15. Spectral reflectance properties (0.4-2.5 um) of secondary Fe-oxide, Fe-hydroxide, and Fe-sulfate-hydrate minerals associated with sulfide-bearing mine waste

    Science.gov (United States)

    Crowley, J.K.; Williams, D.E.; Hammarstrom1, J.M.; Piatak, N.; Mars, J.C.; Chou, I-Ming

    2006-01-01

    Fifteen Fe-oxide, Fe-hydroxide, and Fe-sulphate-hydrate mineral species commonly associated with sulphide bearing mine wastes were characterized by using X-ray powder diffraction and scanning electron microscope methods. Diffuse reflectance spectra of the samples show diagnostic absorption features related to electronic processes involving ferric and/or ferrous iron, and to vibrational processes involving water and hydroxyl ions. Such spectral features enable field and remote sensing based studies of the mineral distributions. Because secondary minerals are sensitive indicators of pH, Eh, relative humidity, and other environmental conditions, spectral mapping of these minerals promises to have important applications to mine waste remediation studies. This report releases digital (ascii) spectra (spectral_data_files.zip) of the fifteen mineral samples to facilitate usage of the data with spectral libraries and spectral analysis software. The spectral data are provided in a two-column format listing wavelength (in micrometers) and reflectance, respectively.

  16. Chemical and biological extraction of metals present in E waste: A hybrid technology.

    Science.gov (United States)

    Pant, Deepak; Joshi, Deepika; Upreti, Manoj K; Kotnala, Ravindra K

    2012-05-01

    Management of metal pollution associated with E-waste is widespread across the globe. Currently used techniques for the extraction of metals from E-waste by using either chemical or biological leaching have their own limitations. Chemical leaching is much rapid and efficient but has its own environmental consequences, even the future prospects of associated nanoremediation are also uncertain. Biological leaching on the other hand is comparatively a cost effective technique but at the same moment it is time consuming and the complete recovery of the metal, alone by biological leaching is not possible in most of the cases. The current review addresses the individual issues related to chemical and biological extraction techniques and proposes a hybrid-methodology which incorporates both, along with safer chemicals and compatible microbes for better and efficient extraction of metals from the E-waste. Copyright © 2011 Elsevier Ltd. All rights reserved.

  17. Iron and aluminium oxides containing industrial wastes as adsorbents of heavy metals: Application possibilities and limitations.

    Science.gov (United States)

    Jacukowicz-Sobala, Irena; Ociński, Daniel; Kociołek-Balawejder, Elżbieta

    2015-07-01

    Industrial wastes with a high iron or aluminium oxide content are produced in huge quantities as by-products of water treatment (water treatment residuals), bauxite processing (red mud) and hard and brown coal burning in power plants (fly ash). Although they vary in their composition, the wastes have one thing in common--a high content of amorphous iron and/or aluminium oxides with a large specific surface area, whereby this group of wastes shows very good adsorbability towards heavy metals, arsenates, selenates, etc. But their physical form makes their utilisation quite difficult, since it is not easy to separate the spent sorbent from the solution and high bed hydraulic resistances occur in dynamic regime processes. Nevertheless, because of the potential benefits of utilising the wastes in industrial effluent treatment, this issue attracts much attention today. This study describes in detail the waste generation processes, the chemical structure of the wastes, their physicochemical properties, and the mechanisms of fixing heavy metals and semimetals on the surface of iron and aluminium oxides. Typical compositions of wastes generated in selected industrial plants are given. A detailed survey of the literature on the adsorption applications of the wastes, including methods of their thermal and chemical activation, as well as regeneration of the spent sorbents, is presented. The existing and potential ways of modifying the physical form of the discussed group of wastes, making it possible to overcome the basic limitation on their practical use, are discussed. © The Author(s) 2015.

  18. Status evaluation of heavy metals in waste disposal sites of ...

    African Journals Online (AJOL)

    The 7.42 pH value during wet season for soil in the Plasto Crown Company waste disposal site indicated alkaline medium which was due to the remnants of the wastes which formed lime to neutralize the acidic medium of the soil while the electrical conductivity values (below 4 dSm-1) indicated the nonsalinity of the soils.

  19. Dissolution Behaviour of Metal Elements from Several Types of E-waste Using Leaching Test

    Science.gov (United States)

    Nor, Nik Hisyamudin Muhd; Amira Nordin, Nurul; Mohamad, Fariza; Jaibee, Shafizan; Ismail, Al Emran; Omar, Badrul; Fauzi Ahmad, Mohd; Rahim, Abd Khalil Abd; Kamaruddin, Muhamad Khalif Ikhwan Mohd; Turan, Faiz Mohd; Abu Bakar, Elmi; Yokoyama, Seiji

    2017-08-01

    Rapid development of the electrical and electronic was increasing annually due to the demand by the human being. Increasing production of electrical and electronic product led to the increasing of electric and electronic waste or can be called as the e-waste. The UN Environment Programme estimates that the world generates 20-50 million tons of the e-waste each year and the amount is raising three times faster than other forms of municipal waste. This study is focusing on the investigation of the dissolution behaviour of metal element from several types of e-waste by hydrometallurgical process. Leaching test was conducted on the e-waste by using acid as the reagent solution. Prior to the leaching test, manual dismantling, separation, and crushing process were carried out to the e-waste. The e-waste were characterized by Scanning Electron Microcopy (SEM) and the Energy Dispersive X-ray Spectroscopy (EDX) to define the elements inside the sample of e-waste. While the liquid residue from leaching test was analyzed by using Inductively Couple Plasma-Mass Spectrometer (ICP-MS) to define the dissolution behaviour of the metal element that contain in the e-waste. It was found that the longest time for dismantling process was the dismantling of laptop. The dissolution behaviour of Fe, Al, Zn and Pb elements in the e-waste has affected to the increase of pH. The increasing pH led to the reduction of the metals element during leaching process.

  20. Structural changes of polyacids initiated by their neutralization with various alkali metal hydroxides. Diffusion studies in poly(acrylic acid)s.

    Science.gov (United States)

    Masiak, Michal; Hyk, Wojciech; Stojek, Zbigniew; Ciszkowska, Malgorzata

    2007-09-27

    The changes in the three-dimensional structure of the poly(acrylic acid), PAA, induced by incorporation of various alkali-metal counterions have been evaluated by studying diffusion of an uncharged probe (1,1'-ferrocenedimethanol) in the polymeric media. The studies are supported by the measurements of conductivity and viscosity of the polymeric media. Solutions of linear PAA of four different sizes (molecular weights: 450,000, 750,000, 1,250,000, 4,000,000) were neutralized with hydroxides of alkali metals of group 1 of the periodic table (Li, Na, K, Rb, Cs) to the desired neutralization degree. The transport properties of the obtained polyacrylates were monitored by measuring the changes in the probe diffusion coefficient during the titration of the polyacids. The probe diffusivity was determined from the steady-state current of the probe voltammetric oxidation at disk microelectrodes. Diffusivity of the probe increases with the increase in the degree of neutralization and with the increase in viscosity. It reaches the maximum value at about 60-80% of the polyacid neutralization. The way the probe diffusion coefficients change is similar in all polyacid solutions and gels. The increase in the size of a metal cation causes, in general, an enhancement in the transport of probe molecules. The biggest differences in the probe diffusivities are between lithium and cesium polyacrylates. The differences between the results obtained for cesium and rubidium are not statistically significant due to lack of good precision of the voltammetric measurements. The measurements of the electric conductivity of polyacrylates and the theoretical predictions supplemented the picture of electrostatic interactions between the polyanionic chains and the metal cations of increasing size. In all instances of the PAAs, the viscosity of the solutions rapidly increases in the 0-60% range of neutralization and then becomes constant in the 60-100% region. With the exception of the shortest

  1. Utilizing waste heat from metal industry for drying of organic waste

    OpenAIRE

    Dobric, Sasa

    2014-01-01

    Growing generation of organic waste is a real problem all over the world. This is specifically expressed in the developed countries because the amounts of the waste are larger. Therefore, it implies problem connected with organic waste disposal. In the modern society it is prohibited to dump the waste on landfills. It was necessary to find the solution how to deal with this situation.One of the options is delivering of the organic waste to the burning facilities. In this way it is possible to...

  2. Pollution distribution of heavy metals in surface soil at an informal electronic-waste recycling site.

    Science.gov (United States)

    Fujimori, Takashi; Takigami, Hidetaka

    2014-02-01

    We studied distribution of heavy metals [lead (Pb), copper (Cu) and zinc (Zn)] in surface soil at an electronic-waste (e-waste) recycling workshop near Metro Manila in the Philippines to evaluate the pollution size (spot size, small area or the entire workshop), as well as to assess heavy metal transport into the surrounding soil environment. On-site length-of-stride-scale (~70 cm) measurements were performed at each surface soil point using field-portable X-ray fluorescence (FP-XRF). The surface soil at the e-waste recycling workshop was polluted with Cu, Zn and Pb, which were distributed discretely in surface soil. The site was divided into five areas based on the distance from an entrance gate (y-axis) of the e-waste recycling workshop. The three heavy metals showed similar concentration gradients in the y-axis direction. Zn, Pb and Cu concentrations were estimated to decrease to half of their maximum concentrations at ~3, 7 and 7 m from the pollution spot, respectively, inside the informal e-waste recycling workshop. Distance from an entrance may play an important role in heavy metal transport at the soil surface. Using on-site FP-XRF, we evaluated the metal ratio to characterise pollution features of the solid surface. Variability analysis of heavy metals revealed vanishing surficial autocorrelation over metre ranges. Also, the possibility of concentration prediction at unmeasured points using geostatistical kriging was evaluated, and heavy metals had a relative "small" pollution scales and remained inside the original workshop compared with toxic organohalogen compounds. Thus, exposure to heavy metals may directly influence the health of e-waste workers at the original site rather than the surrounding habitat and environmental media.

  3. Waste printing paper as analogous adsorbents for heavy metals in ...

    African Journals Online (AJOL)

    H2O), 0.1M nitric acid, (HNO3), and ethylenediaminetetracetic acid (EDTA) was evaluated for possible recovery of Pb2+. The results showed WPP has adsorption efficacy of >90.0% and metal uptake of ≤ 25 mg/g for the assessed metal ions. There was high effect of metal dosage and contact time on WPP adsorption ...

  4. Calcium hydroxide poisoning

    Science.gov (United States)

    Hydrate - calcium; Lime milk; Slaked lime ... Calcium hydroxide ... These products contain calcium hydroxide: Cement Limewater Many industrial solvents and cleaners (hundreds to thousands of construction products, flooring strippers, brick cleaners, cement ...

  5. Toxic metals in WEEE: characterization and substance flow analysis in waste treatment processes.

    Science.gov (United States)

    Oguchi, Masahiro; Sakanakura, Hirofumi; Terazono, Atsushi

    2013-10-01

    Waste electrical and electronic equipment (WEEE) has received extensive attention as a secondary source of metals. Because WEEE also contains toxic substances such as heavy metals, appropriate management of these substances is important in the recycling and treatment of WEEE. As a basis for discussion toward better management of WEEE, this study characterizes various types of WEEE in terms of toxic metal contents. The fate of various metals contained in WEEE, including toxic metals, was also investigated in actual waste treatment processes. Cathode-ray tube televisions showed the highest concentration and the largest total amount of toxic metals such as Ba, Pb, and Sb, so appropriate recycling and disposal of these televisions would greatly contribute to better management of toxic metals in WEEE. A future challenge is the management of toxic metals in mid-sized items such as audio/visual and ICT equipment because even though the concentrations were not high in these items, the total amount of toxic metals contained in them is not negligible. In the case of Japan, such mid-sized WEEE items as well as small electronic items are subject to municipal solid waste treatment. A case study showed that a landfill was the main destination of toxic metals contained in those items in the current treatment systems. The case study also showed that changes in the flows of toxic metals will occur when treatment processes are modified to emphasize resource recovery. Because the flow changes might lead to an increase in the amount of toxic metals released to the environment, the flows of toxic metals and the materials targeted for resource recovery should be considered simultaneously. Copyright © 2012 Elsevier B.V. All rights reserved.

  6. Characteristics of metal waste forms containing technetium and uranium

    Energy Technology Data Exchange (ETDEWEB)

    Fortner, J.A.; Kropf, A.J.; Ebert, W.L. [Argonne National Laboratory, Argonne, IL 60439 (United States)

    2013-07-01

    2 prototype alloys: RAW-1(Tc) and RAW-2(UTc) suitable for a wide range of waste stream compositions are being evaluated to support development of a waste form degradation model that can be used to calculate radionuclide source terms for a range of waste form compositions and disposal environments. Tests and analyses to support formulation of waste forms and development of the degradation model include detailed characterizations of the constituent phases using SEM/EDS and TEM, electrochemical tests to quantify the oxidation behavior and kinetics of the individual and coupled phases under a wide range of environmental conditions, and corrosion tests to measure the gross release kinetics of radionuclides under aggressive test conditions.

  7. Urban Biomining: Biological Extraction of Metals and Materials from Electronics Waste Using a Synthetic Biology Approach

    Science.gov (United States)

    Urbina-Navarrete, J.; Rothschild, L.

    2016-12-01

    End-of-life electronics waste (e-waste) containing toxic and valuable materials is a rapidly progressing human health and environmental issue. Using synthetic biology tools, we have developed a recycling method for e-waste. Our innovation is to use a recombinant version of a naturally-occurring silica-degrading enzyme to depolymerize the silica in metal- and glass- containing e-waste components, and subsequently, to use engineered bacterial surfaces to bind and separate metals from a solution. The bacteria with bound metals can then be used as "bio-ink" to print new circuits using a novel plasma jet electronics printing technology. Here, we present the results from our initial studies that focus on the specificity of metal-binding motifs for a cognate metal. The candidate motifs that show high affinity and specificity will be engineered into bacterial surfaces for downstream applications in biologically-mediated metal recycling. Since the chemistry and role of Cu in metalloproteins is relatively well-characterized, we are using Cu as a proxy to elucidate metal and biological ligand interactions with various metals in e-waste. We assess the binding parameters of 3 representative classes of Cu-binding motifs using isothermal titration calorimetry; 1) natural motifs found in metalloproteins, 2) consensus motifs, and 3) rationally designed peptides that are predicted, in silico, to bind Cu. Our results indicate that naturally-occurring motifs have relative high affinity and specificity for Cu (association constant for Cu Ka 104 M-1, Zn Ka 103 M-1) when competing ions are present in the aqueous milieu. However, motifs developed through rational design by applying quantum mechanical methods that take into account complexation energies of the elemental binding partners and molecular geometry of the cognate metal, not only show high affinity for the cognate metal (Cu Ka 106 M-1), but they show specificity and discrimination against other metal ions that would be

  8. Informal E-waste recycling in developing countries: review of metal(loid)s pollution, environmental impacts and transport pathways.

    Science.gov (United States)

    Ackah, Michael

    2017-11-01

    Crude or primitive recycling practices are often adopted in material resource recovery from E-waste in developing nations. Significant human health and environmental impacts may occur because of such practices. Literature on metal(loid)s pollution during E-waste processing is fragmented. Here, I review the health and environmental impacts of E-waste recycling operations and transport pathways of metal(loid)s, dispersed during operations. This paper is organised into five sections. Section 1 relates to the background of global E-waste generation and legal/illegal trade, citing specific cases from Ghana and other developing nations. Section 2 provides a brief information on sources of metal(loid)s in E-waste. Section 3 describes characteristics of informal E-waste recycling operations in developing nations. Section 4 examines the health and environmental impacts in E-waste recycling while section 5 evaluates major transport pathways of metal(loid)s contaminants.

  9. Enhancement of concrete properties for pavement slabs using waste metal drillings and silica fume.

    Science.gov (United States)

    Hassani, Abolfazl; Arjmandi, Mohsen

    2010-01-01

    This paper presents a comparative study on the effects of steel fibres and waste metal drillings on the mechanical/physical behaviour of conventional and silica fume concrete. The amount of silica fume used was 10% of cement by mass and the amount of steel fibres and metal drillings used in both concrete mixtures was 0.5% by concrete volume for steel fibres and 0.0, 0.25, 0.50 and 0.75% for metal drillings, respectively. In total, 10 different mixtures were made and tested for compressive strength, modulus of elasticity, flexural strength and toughness. Our data reveal the significant impact of the effect of silica fume, steel fibres and industrial waste metal drillings on the mechanical and physical characteristics of concrete mixtures. The results also show that mixtures with steel fibres and waste metal drillings have comparable behaviour. Hence, there is a potential for use of waste metal drillings as an alternative to steel fibres for specific cases such as concrete pavement slabs.

  10. Highly selective and efficient removal of fluoride from ground water by layered Al-Zr-La Tri-metal hydroxide

    Science.gov (United States)

    Zhou, Jian; Zhu, Wenkun; Yu, Jie; Zhang, Hongping; Zhang, Yongde; Lin, Xiaoyan; Luo, Xuegang

    2018-03-01

    A novel layered Zr-Al-La tri-metal composite (AZL) was fabricated via co-precipitation method for fluoride removal. The as-prepared adsorbent was characterized by various technologies, and its adsorption behaviors to fluoride were thoroughly carried out to investigate the fluoride removal performance. The results showed that the layered structure existed and the AZL exhibited the maximum adsorption capacity of 90.48 mg g-1 at 308 K and pH 3.0 from the Langmuir isotherm model. The adsorption kinetics was well fitted by the pseudo-second-order equation, and the adsorption isotherms were well described by the Langmuir equation. Adsorption thermodynamics result was indicative of endothermic reaction in the process of adsorption of AZL to fluoride. The as-prepared AZL composite has excellent fluoride removal performance for the practical ground water and satisfies the permissible limit of fluoride in drinking water recommended by Chinese Standard. In addition, based on the characterization, the adsorption mechanism of fluoride on AZL was proposed, including electrostatic interaction between the protonated surface of AZL and fluoride, as well as ion-exchange by hydroxyl group and fluoride.

  11. Distribution of heavy metals and hydrocarbon contents in an alfisol contaminated with waste-lubricating oil amended with organic wastes.

    Science.gov (United States)

    Adesodun, J K; Mbagwu, J S C

    2008-05-01

    Contamination of soil and groundwater with mineral oil-based products is among the most common sources of pollution in Nigeria. This study evaluated the distribution of some heavy metals and hydrocarbon content in soil contaminated with waste-lubricating oil (spent oil), and the effectiveness of some abundantly available organic wastes from animal source as remediation alternative to the expensive chemical and physical methods. The main-plot treatments include control (C), cow dung (CD), poultry manure (PM) and pig waste (PW) applied at 10Mg/ha each; while the sub-plot treatments were control (0%), 0.5%, 2.5% and 5% spent oil (SP) applied at 10, 50 and 100 Mg/ha, respectively arranged in a split-plot in Randomized Complete Block Design (RCBD) with four replications. These treatments were applied once each year for two consecutive years. Soil samples (0-20 cm) were collected at 3, 6 and 12 months each year and analyzed for Cr, Ni, Pb and Zn, while the residual total hydrocarbon content (THC) was determined at the end of the 2 years study. Results show significant (poil pollution following the sequence 5%SP>2.5%SP>0.5%SP, indicating higher metal pollution with increase in oil pollution. General distribution of Cr, Ni, Pb and Zn, relative to sampling periods, followed 3 months>6 months>12 months in the 1st year indicating reduction in metal levels with time. The trend for 2nd year indicated higher accumulation of Cr and Ni in 12 months, while Pb and Zn decreased with time of sampling. The results further showed higher accumulation of Cr followed by Zn, relative to other metals, with oil pollution. However, addition of organic wastes to the oil polluted soils significantly (pPW>CD.

  12. Noble metal behavior during melting of simulated high-level nuclear waste glass feeds

    Energy Technology Data Exchange (ETDEWEB)

    Anderson, L.D.; Dennis, T.; Elliott, M.L.; Hrma, P.

    1993-04-01

    Noble metals and their oxides can settle in waste glass melters and cause electrical shorting. Simulated waste feeds from Hanford, Savannah River, and Germany were heat treated for 1 hour in a gradient furnace at temperatures ranging from approximately 600{degrees}C--1000{degrees}C and examined by electron microscopy to determine shapes, sizes, and distribution of noble metal particles as a function of temperature. Individual noble metal particles and agglomerates of rhodium (Rh), ruthenium (RuO{sub 2}), and palladium (Pd), as well as their alloys, were seen. the majority of particles and agglomerates were generally less than 10 microns; however, large agglomerations (up to 1 mm) were found in the German feed. Detailed particle distribution and characterization was performed for a Hanford waste to provide input to computer modeling of particle settling in the melter.

  13. Carbonized waste for the cut-down of environmental pollution with heavy metals

    Science.gov (United States)

    Gmucová, K.; Morvová, M.; Havránek, E.; Kliman, J.; Košinár, I.; Kunecová, D.; Malakhov, A. I.; Anisimov, Yu. S.; Morva, I.; Siváček, I.; Sýkorová, M.; Šatka, A.

    2011-07-01

    Nowadays, an increasing concern about the treatment and disposal of waters contaminated by toxic heavy metals is noticed. The toxic pollutants must be removed from the sewage water which then is fed back into the materials cycle. Any candidate technology should result in reusable by-products. With this in mind, the aim of the present study is to test a low cost procedure for utilization of the carbonized waste, a product of PET (polyethylene terephthalate) bottles pyrolysis on sand bedding, for this purpose. Both the water present in PET bottles waste and combustion exhaust probably contribute to the conversion of carbon char to activated carbon directly within the pyrolysis oven. Preliminary results, obtained for several heavy metal ions under laboratory conditions are presented and discussed. Adsorption of heavy metals on the carbonized PET waste is tested by both the electrochemical methods and X-ray fluorescence spectrometry. A simple desorption procedure for the regeneration of prepared active carbon is proposed.

  14. Reducing hazardous heavy metal ions using mangium bark waste.

    Science.gov (United States)

    Khabibi, Jauhar; Syafii, Wasrin; Sari, Rita Kartika

    2016-08-01

    The objective of this study was to evaluate the characteristics of mangium bark and its biosorbent ability to reduce heavy metal ions in standard solutions and wastewater and to assess changes in bark characteristics after heavy metal absorption. The experiments were conducted to determine heavy metal absorption from solutions of heavy metals alone and in mixtures as well as from wastewater. The results show that mangium bark can absorb heavy metals. Absorption percentages and capacities from single heavy metal solutions showed that Cu(2+) > Ni(2+) > Pb(2+) > Hg(2+), while those from mixture solutions showed that Hg(2+) > Cu(2+) > Pb(2+) > Ni(2+). Wastewater from gold mining only contained Cu, with an absorption percentage and capacity of 42.87 % and 0.75 mg/g, respectively. The highest absorption percentage and capacity of 92.77 % and 5.18 mg/g, respectively, were found for Hg(2+) in a mixture solution and Cu(2+) in single-metal solution. The Cu(2+) absorption process in a single-metal solution changed the biosorbent characteristics of the mangium bark, yielding a decreased crystalline fraction; changed transmittance on hydroxyl, carboxyl, and carbonyl groups; and increased the presence of Cu. In conclusion, mangium bark biosorbent can reduce hazardous heavy metal ions in both standard solutions and wastewater.

  15. Safety evaluation of the leaching of metals from the printed graphic product wastes

    OpenAIRE

    Savka Adamović; Miljana Prica; Jelena Radonić; Maja Turk Sekulić; Szabolcs Pap

    2015-01-01

    Due to the technological development of the graphic production, the environment is being faced with a large amount of printed graphic product wastes, especially packaging materials (paper, cardboard, paper and plastic bags, films, etc), but it is also being faced with the problem of their disposal. Many printing inks and coatings used in the production of the printed graphic product contain metals which, after the disposal of graphic waste, can migrate to different systems and have a negative...

  16. Noble Metals and Spinel Settling in High Level Waste Glass Melters

    Energy Technology Data Exchange (ETDEWEB)

    Sundaram, S. K.; Perez, Joseph M.

    2000-09-30

    In the continuing effort to support the Defense Waste Processing Facility (DWPF), the noble metals issue is addressed. There is an additional concern about the amount of noble metals expected to be present in the future batches that will be considered for vitrification in the DWPF. Several laboratory, as well as melter-scale, studies have been completed by various organizations (mainly PNNL, SRTC, and WVDP in the USA). This letter report statuses the noble metals issue and focuses at the settling of noble metals in melters.

  17. Growth and metal bioconcentration by conspecific freshwater macroalgae cultured in industrial waste water

    Directory of Open Access Journals (Sweden)

    Michael B. Ellison

    2014-05-01

    Full Text Available The bioremediation of industrial waste water by macroalgae is a sustainable and renewable approach to the treatment of waste water produced by multiple industries. However, few studies have tested the bioremediation of complex multi-element waste streams from coal-fired power stations by live algae. This study compares the ability of three species of green freshwater macroalgae from the genus Oedogonium, isolated from different geographic regions, to grow in waste water for the bioremediation of metals. The experiments used Ash Dam water from Tarong power station in Queensland, which is contaminated by multiple metals (Al, Cd, Ni and Zn and metalloids (As and Se in excess of Australian water quality guidelines. All species had consistent growth rates in Ash Dam water, despite significant differences in their growth rates in “clean” water. A species isolated from the Ash Dam water itself was not better suited to the bioremediation of that waste water. While there were differences in the temporal pattern of the bioconcentration of metals by the three species, over the course of the experiment, all three species bioconcentrated the same elements preferentially and to a similar extent. All species bioconcentrated metals (Cu, Mn, Ni, Cd and Zn more rapidly than metalloids (As, Mo and Se. Therefore, bioremediation in situ will be most rapid and complete for metals. Overall, all three species of freshwater macroalgae had the ability to grow in waste water and bioconcentrate elements, with a consistent affinity for the key metals that are regulated by Australian and international water quality guidelines. Together, these characteristics make Oedogonium a clear target for scaled bioremediation programs across a range of geographic regions.

  18. TREATMENT OF METAL-LADEN HAZARDOUS WASTES WITH ADVANCED CLEAN COAL TECHNOLOGY BY-PRODUCTS

    Energy Technology Data Exchange (ETDEWEB)

    James T. Cobb, Jr.

    2003-09-12

    Metal-laden wastes can be stabilized and solidified using advanced clean coal technology by-products (CCTBs)--fluid bed combustor ash and spray drier solids. These utility-generated treatment chemicals are available for purchase through brokers, and commercial applications of this process are being practiced by treaters of metal-laden hazardous waste. A complex of regulations governs this industry, and sensitivities to this complex has discouraged public documentation of treatment of metal-laden hazardous wastes with CCTBs. This report provides a comprehensive public documentation of laboratory studies that show the efficacy of the stabilization and solidification of metal-laden hazardous wastes--such as lead-contaminated soils and sandblast residues--through treatment with CCTBs. It then describes the extensive efforts that were made to obtain the permits allowing a commercial hazardous waste treater to utilize CCTBs as treatment chemicals and to install the equipment required to do so. It concludes with the effect of this lengthy process on the ability of the treatment company to realize the practical, physical outcome of this effort, leading to premature termination of the project.

  19. Heavy Metal Contamination of Soils around a Hospital Waste Incinerator Bottom Ash Dumps Site

    Directory of Open Access Journals (Sweden)

    M. Adama

    2016-01-01

    Full Text Available Waste incineration is the main waste management strategy used in treating hospital waste in many developing countries. However, the release of dioxins, POPs, and heavy metals in fly and bottom ash poses environmental and public health concerns. To determine heavy metal (Hg, Pb, Cd, Cr, and Ag in levels in incinerator bottom ash and soils 100 m around the incinerator bottom ash dump site, ash samples and surrounding soil samples were collected at 20 m, 40 m, 60 m, 80 m, 100 m, and 1,200 m from incinerator. These were analyzed using the absorption spectrophotometer method. The geoaccumulation (Igeo and pollution load indices (PLI were used to assess the level of heavy metal contamination of surrounding soils. The study revealed high concentrations in mg/kg for, Zn (16417.69, Pb (143.80, Cr (99.30, and Cd (7.54 in bottom ash and these were above allowable limits for disposal in landfill. The study also found soils within 60 m radius of the incinerator to be polluted with the metals. It is recommended that health care waste managers be educated on the implication of improper management of incinerator bottom ash and regulators monitor hospital waste incinerator sites.

  20. Metals recovering from waste printed circuit boards (WPCBs) using molten salts.

    Science.gov (United States)

    Flandinet, L; Tedjar, F; Ghetta, V; Fouletier, J

    2012-04-30

    Recycling of waste electrical and electronic equipments (WEEE) has been taken into consideration in the literature due to the large quantity of concerned wastes and their hazardous contents. The situation is so critical that EU published European Directives imposing collection and recycling with a minimum of material recovery [1]. Moreover, WEEEs contain precious metals, making the recycling of these wastes economically interesting, but also some critical metals and their recycling leads to resource conservation. This paper reports on a new approach for recycling waste printed circuit boards (WPCBs). Molten salts and specifically molten KOH-NaOH eutectic is used to dissolve glasses, oxides and to destruct plastics present in wastes without oxidizing the most valuable metals. This method is efficient for recovering a copper-rich metallic fraction, which is, moreover, cleared of plastics and glasses. In addition, analyses of gaseous emission show that this method is environmentally friendly since most of the process gases, such as carbon monoxide and dioxide and halogens, are trapped in the highly basic molten salt. In other respects, under operation without oxygen, a large quantity of hydrogen is produced and might be used as fuel gas or as synthesis gas, leading to a favourable energy balance for this new process. Copyright © 2012 Elsevier B.V. All rights reserved.

  1. Removal and recovery of radionuclides and toxic metals from wastes, soils and materials

    Energy Technology Data Exchange (ETDEWEB)

    Francis, A.J.

    1993-07-01

    A process has been developed at Brookhaven National Laboratory (BNL) for the removal of metals and radionuclides from contaminated materials, soils, and waste sites (Figure 1). In this process, citric acid, a naturally occurring organic complexing agent, is used to extract metals such as Ba, Cd, Cr, Ni, Zn, and radionuclides Co, Sr, Th, and U from solid wastes by formation of water soluble, metal-citrate complexes. Citric acid forms different types of complexes with the transition metals and actinides, and may involve formation of a bidentate, tridentate, binuclear, or polynuclear complex species. The extract containing radionuclide/metal complex is then subjected to microbiological degradation followed by photochemical degradation under aerobic conditions. Several metal citrate complexes are biodegraded and the metals are recovered in a concentrated form with the bacterial biomass. Uranium forms binuclear complex with citric acid and is not biodegraded. The supernatant containing uranium citrate complex is separated and upon exposure to light, undergoes rapid degradation resulting in the formation of an insoluble, stable polymeric form of uranium. Uranium is recovered as a precipitate (uranium trioxide) in a concentrated form for recycling or for appropriate disposal. This treatment process, unlike others which use caustic reagents, does not create additional hazardous wastes for disposal and causes little damage to soil which can then be returned to normal use.

  2. Removal of heavy metals from waste water of tanning leather ...

    African Journals Online (AJOL)

    unguis. The isolated fungi were investigated for their potential to remove heavy metals from wastewater effluent of tanning leather industry. Such effluent was alkaline (pH, 8.2) with high content of total soluble salts (30.6 mS/cm) and heavy metals ...

  3. Structural transformation of nickel hydroxide films during anodic oxidation

    Energy Technology Data Exchange (ETDEWEB)

    Crocker, Robert W. [Univ. of California, Berkeley, CA (United States); Muller, Rolf H. [Univ. of California, Berkeley, CA (United States)

    1992-05-01

    The transformation of anodically formed nickel hydroxide/oxy-hydroxide electrodes has been investigated. A mechanism is proposed for the anodic oxidation reaction, in which the reaction interface between the reduced and oxidized phases of the electrode evolves in a nodular topography that leads to inefficient utilization of the active electrode material. In the proposed nodular transformation model for the anodic oxidation reaction, nickel hydroxide is oxidized to nickel oxy-hydroxide in the region near the metal substrate. Since the nickel oxy-hydroxide is considerably more conductive than the surrounding nickel hydroxide, as further oxidation occurs, nodular features grow rapidly to the film/electrolyte interface. Upon emerging at the electrolyte interface, the reaction boundary between the nickel hydroxide and oxy-hydroxide phases spreads laterally across the film/electrolyte interface, creating an overlayer of nickel oxy-hydroxide and trapping uncharged regions of nickel hydroxide within the film. The nickel oxy-hydroxide overlayer surface facilitates the oxygen evolution side reaction. Scanning tunneling microscopy of the electrode in its charged state revealed evidence of 80 - 100 Angstrom nickel oxy-hydroxide nodules in the nickel hydroxide film. In situ spectroscopic ellipsometer measurements of films held at various constant potentials agree quantitatively with optical models appropriate to the nodular growth and subsequent overgrowth of the nickel oxy-hydroxide phase. A two-dimensional, numerical finite difference model was developed to simulate the current distribution along the phase boundary between the charged and uncharged material. The model was used to explore the effects of the physical parameters that govern the electrode behavior. The ratio of the conductivities of the nickel hydroxide and oxy-hydroxide phases was found to be the dominant parameter in the system.

  4. Structural transformation of nickel hydroxide films during anodic oxidation

    Energy Technology Data Exchange (ETDEWEB)

    Crocker, R.W.; Muller, R.H.

    1992-05-01

    The transformation of anodically formed nickel hydroxide/oxy-hydroxide electrodes has been investigated. A mechanism is proposed for the anodic oxidation reaction, in which the reaction interface between the reduced and oxidized phases of the electrode evolves in a nodular topography that leads to inefficient utilization of the active electrode material. In the proposed nodular transformation model for the anodic oxidation reaction, nickel hydroxide is oxidized to nickel oxy-hydroxide in the region near the metal substrate. Since the nickel oxy-hydroxide is considerably more conductive than the surrounding nickel hydroxide, as further oxidation occurs, nodular features grow rapidly to the film/electrolyte interface. Upon emerging at the electrolyte interface, the reaction boundary between the nickel hydroxide and oxy-hydroxide phases spreads laterally across the film/electrolyte interface, creating an overlayer of nickel oxy-hydroxide and trapping uncharged regions of nickel hydroxide within the film. The nickel oxy-hydroxide overlayer surface facilitates the oxygen evolution side reaction. Scanning tunneling microscopy of the electrode in its charged state revealed evidence of 80 {endash} 100 Angstrom nickel oxy-hydroxide nodules in the nickel hydroxide film. In situ spectroscopic ellipsometer measurements of films held at various constant potentials agree quantitatively with optical models appropriate to the nodular growth and subsequent overgrowth of the nickel oxy-hydroxide phase. A two-dimensional, numerical finite difference model was developed to simulate the current distribution along the phase boundary between the charged and uncharged material. The model was used to explore the effects of the physical parameters that govern the electrode behavior. The ratio of the conductivities of the nickel hydroxide and oxy-hydroxide phases was found to be the dominant parameter in the system.

  5. Absorbtion Activity of Cassava Peel (Manihot utilissima as Chromium (VI Metal Biosorbent in Electroplating Waste

    Directory of Open Access Journals (Sweden)

    Iin Candrawati

    2017-05-01

    Full Text Available Electroplating is a process of metal veneering with another metal using the electric energy. The water waste of electroplating industry contains many kinds of heavy metal ions, especially chromium (Cr6+ which might cause pollutions if it's not processed and it presents above the threshold allowed . The use of cellulose can be a solution, because it has the functional groups which form bonding with the metal ions. Cassava peel is one of the sources of cellulose which contains 80-85% of cellulose. This proves that cassava peel (Manihot utilissimaI has the potential as the heavy metal biosorbent of chromium metal in electroplating waste. The methodology of the research is conducted in a series including analysis of heavy metal concentrations of chromium (VI in electroplating waste, biosorption treatment of cassava peel (Manihot utilissimaI biosorbent activated by HNO3 1.5 M in electroplating waste with batch method, and analysis of heavy metal concentrations of chromium (VI in electroplating waste after biosorbtion process. Variation of biosorbent’s mass are (0.1, 0.2, 0.3, 0.4, 0.5 grams, and variation of biosorbent’s contact time are (10, 20, 30, 40, 50 minutes. The result of the AAS (Atomic Absorbtion Spectrophotometry shows that the level of total chromium in electroplating waste reaches 2.0777 ± 0.2785 ppm, so the chromium test solution used in this research is 2 ppm to know the optimum conditions of % chromium (VI absorbed with variation of mass and contact time. From the results of this research, the optimum mass and contact time of cassava peel biosorbent activated by HNO3 1.5 M in % chromium (VI absorbed are 0.1 gram and 40 minute. Finally, the optimum mass and contact time of cassava peel biosorbent activated by HNO3 1.5 M is applied to electroplating waste. The average of % chromium absorbed in electroplating waste with the addition of cassava peel biosorbent activated by HNO3 1.5 M is 61.72%.

  6. Sorption Potentials of Waste Tyre for Some Heavy Metals (Pb Cd in Aqueous Solution

    Directory of Open Access Journals (Sweden)

    Austin Kanayo ASIAGWU

    2009-07-01

    Full Text Available An investigation into the adsorption potential of activated and inactivated waste tyre powders for some heavy metals (Pb2+ and Cd2+ in their aqueous solution has been studied. The result indicated that inactivated waste tyre is a good non-conventional adsorbent for the removal of Cd from aqueous solution. A total of 93.3% of Cadmium contents was removed. The inactivated waste type proved a good adsorbent for the removal of Pb2+ 5g of 500mm activated tyre removed over 86.66% of Pb2+ from solution.

  7. SIMULANT DEVELOPMENT FOR SAVANNAH RIVER SITE HIGH LEVEL WASTE

    Energy Technology Data Exchange (ETDEWEB)

    Stone, M; Russell Eibling, R; David Koopman, D; Dan Lambert, D; Paul Burket, P

    2007-09-04

    The Defense Waste Processing Facility (DWPF) at the Savannah River Site vitrifies High Level Waste (HLW) for repository internment. The process consists of three major steps: waste pretreatment, vitrification, and canister decontamination/sealing. The HLW consists of insoluble metal hydroxides (primarily iron, aluminum, magnesium, manganese, and uranium) and soluble sodium salts (carbonate, hydroxide, nitrite, nitrate, and sulfate). The HLW is processed in large batches through DWPF; DWPF has recently completed processing Sludge Batch 3 (SB3) and is currently processing Sludge Batch 4 (SB4). The composition of metal species in SB4 is shown in Table 1 as a function of the ratio of a metal to iron. Simulants remove radioactive species and renormalize the remaining species. Supernate composition is shown in Table 2.

  8. Toxic metals in WEEE: Characterization and substance flow analysis in waste treatment processes

    Energy Technology Data Exchange (ETDEWEB)

    Oguchi, Masahiro, E-mail: oguchi.masahiro@nies.go.jp; Sakanakura, Hirofumi; Terazono, Atsushi

    2013-10-01

    Waste electrical and electronic equipment (WEEE) has received extensive attention as a secondary source of metals. Because WEEE also contains toxic substances such as heavy metals, appropriate management of these substances is important in the recycling and treatment of WEEE. As a basis for discussion toward better management of WEEE, this study characterizes various types of WEEE in terms of toxic metal contents. The fate of various metals contained in WEEE, including toxic metals, was also investigated in actual waste treatment processes. Cathode-ray tube televisions showed the highest concentration and the largest total amount of toxic metals such as Ba, Pb, and Sb, so appropriate recycling and disposal of these televisions would greatly contribute to better management of toxic metals in WEEE. A future challenge is the management of toxic metals in mid-sized items such as audio/visual and ICT equipment because even though the concentrations were not high in these items, the total amount of toxic metals contained in them is not negligible. In the case of Japan, such mid-sized WEEE items as well as small electronic items are subject to municipal solid waste treatment. A case study showed that a landfill was the main destination of toxic metals contained in those items in the current treatment systems. The case study also showed that changes in the flows of toxic metals will occur when treatment processes are modified to emphasize resource recovery. Because the flow changes might lead to an increase in the amount of toxic metals released to the environment, the flows of toxic metals and the materials targeted for resource recovery should be considered simultaneously. - Highlights: ► Appropriate management of toxic metals contained in WEEE is important during recycling and treatment of WEEE. ► CRT TVs contain large amount of toxic metals with high concentration and thus appropriate management is highly important. ► Mid-sized equipment is a future target for

  9. Metals and polybrominated diphenyl ethers leaching from electronic waste in simulated landfills

    Energy Technology Data Exchange (ETDEWEB)

    Kiddee, Peeranart [Centre for Environmental Risk Assessment and Remediation, University of South Australia, Mawson Lakes Campus, Adelaide, 5095 (Australia); Cooperative Research Centre for Contamination Assessment and Remediation of the Environment, Mawson Lakes Campus, Adelaide, 5095 (Australia); Naidu, Ravi, E-mail: ravi.naidu@crccare.com [Centre for Environmental Risk Assessment and Remediation, University of South Australia, Mawson Lakes Campus, Adelaide, 5095 (Australia); Cooperative Research Centre for Contamination Assessment and Remediation of the Environment, Mawson Lakes Campus, Adelaide, 5095 (Australia); Wong, Ming H. [Croucher Institute for Environmental Sciences, and Department of Biology, Hong Kong Baptist University, Kowloon Tong (China)

    2013-05-15

    Highlights: • Simulated landfill columns provided realistic results than lab based column study. • Column leachates showed significant seasonal effect on toxic substances. • Toxic substances in the landfill leachates pose environmental and health hazards. • A better management of e-waste is urgently needed. -- Abstract: Landfills established prior to the recognition of potential impacts from the leaching of heavy metals and toxic organic compounds often lack appropriate barriers and pose significant risks of contamination of groundwater. In this study, bioavailable metal(oids) and polybrominated diphenyl ethers (PBDEs) in leachates from landfill columns that contained intact or broken e-waste were studied under conditions that simulate landfills in terms of waste components and methods of disposal of e-wastes, and with realistic rainfall. Fourteen elements and PBDEs were analysed in leachates over a period of 21 months. The results demonstrate that the average concentrations of Al, Ba, Be, Cd, Co, Cr, Cu, Ni, Pb, Sb and V in leachates from the column that contained broken e-waste items were significantly higher than the column without e-waste. BDE-153 was the highest average PBDEs congener in all columns but the average of ∑PBDEs levels in columns that contained intact e-waste were (3.7 ng/l) and were not significantly higher than that in the leachates from the control column.

  10. Dissolvable layered double hydroxide as an efficient nanosorbent for centrifugeless air-agitated dispersive solid-phase extraction of potentially toxic metal ions from bio-fluid samples

    Energy Technology Data Exchange (ETDEWEB)

    Rajabi, Maryam, E-mail: mrajabi@semnan.ac.ir; Arghavani-Beydokhti, Somayeh; Barfi, Behruz; Asghari, Alireza

    2017-03-08

    In the present work, a novel nanosorbent namely layered double hydroxides with 4-amino-5-hydroxyl-2,7-naphthalendisulfonic acid monosodium salt interlayer anion (Mg-Al-AHNDA-LDH) was synthesized and applied as a dissolvable nanosorbent in a centrifugeless ultrasound-enhanced air-agitated dispersive solid-phase extraction (USE-AA-D-SPE) method. This method was used for the separation and preconcentration of some metal ions including Cd{sup 2+}, Cr{sup 6+}, Pb{sup 2+}, Co{sup 2+}, and Ni{sup 2+} prior to their determination using the micro-sampling flame atomic absorption spectrometry (MS-FAAS) technique. The most interesting aspect of this nanosorbent is its immediate dissolvability at pH values lower than 4. This capability drastically eliminates the elution step, leading to a great improvement in the extraction efficiency and a decrease in the extraction time. Also in this method, the use of a syringe nanofilter eliminates the need for the centrifugation step, which is time-consuming and essentially causes the analysis to be off-line. Several effective parameters governing the extraction efficiency including the sample solution pH, amount of nanosorbent, eluent condition, number of air-agitation cycles, and sonication time were investigated and optimized. Under the optimized conditions, the good linear dynamic ranges of 2–70, 6–360, 7–725, 7–370, and 8–450 ng mL{sup −1} for the Cd{sup 2+}, Cr{sup 6+}, Pb{sup 2+}, Co{sup 2+}and Ni{sup 2+} ions, respectively, with the correlation of determinations (R{sup 2}s) higher than 0.997 were obtained. The limits of detection (LODs) were found to be 0.6, 1.7, 2.0, 2.1, and 2.4 for the Cd{sup 2+}, Cr{sup 6+}, Pb{sup 2+}, Co{sup 2+}, and Ni{sup 2+} ions, respectively. The intra-day and inter-day precisions (percent relative standard deviations (%RSDs) (n = 5)) were below 7.8%. The proposed method was also successfully applied for the extraction and determination of the target ions in different biological fluid

  11. Decomposition Mechanism and Decomposition Promoting Factors of Waste Hard Metal for Zinc Decomposition Process (ZDP)

    Energy Technology Data Exchange (ETDEWEB)

    Pee, J H; Kim, Y J; Kim, J Y; Cho, W S; Kim, K J [Whiteware Ceramic Center, KICET (Korea, Republic of); Seong, N E, E-mail: pee@kicet.re.kr [Recytech Korea Co., Ltd. (Korea, Republic of)

    2011-10-29

    Decomposition promoting factors and decomposition mechanism in the zinc decomposition process of waste hard metals which are composed mostly of tungsten carbide and cobalt were evaluated. Zinc volatility amount was suppressed and zinc steam pressure was produced in the reaction graphite crucible inside an electric furnace for ZDP. Reaction was done for 2 hrs at 650 deg. C, which 100% decomposed the waste hard metals that were over 30 mm thick. As for the separation-decomposition of waste hard metals, zinc melted alloy formed a liquid composed of a mixture of {gamma}-{beta}1 phase from the cobalt binder layer (reaction interface). The volume of reacted zone was expanded and the waste hard metal layer was decomposed-separated horizontally from the hard metal. Zinc used in the ZDP process was almost completely removed-collected by decantation and volatilization-collection process at 1000 deg. C. The small amount of zinc remaining in the tungsten carbide-cobalt powder which was completely decomposed was fully removed by using phosphate solution which had a slow cobalt dissolution speed.

  12. Feasibility of using demolition waste as an alternative heavy metal immobilising agent.

    Science.gov (United States)

    Damrongsiri, Seelawut

    2017-05-01

    Demolition waste consisting of cement paste, lightweight concrete and bricks is a worthless material generated by a growing city. However, research suggests that it may be applied as an alternative heavy metal immobilising agent. The diverse characteristics of demolition waste were examined. Cadmium was selected as there presentative heavy metal to investigate demolition waste adsorption capacity. The solid-liquid distribution coefficients (Kd) were observed. The adsorption isotherms were applied to investigate adsorption characteristics. Carbon content in the demolition waste materials was low and mainly in inorganic form. Cement paste and lightweight concrete had an alkaline pH with very high acid neutralising capacity (ANC). The surface area and cation exchange capacity (CEC) of these materials were low. Cement paste possessed the highest pH, ANC, CEC and surface area, with the highest Kd; however, its specific surface area and CEC were low compared to activated carbon and organic material. The adsorption isotherms indicated surface heterogeneity with favourable conditions for adsorption and the mean free energy suggested physisorption with multilayer formation. The Kd values of the tested materials were comparable to soil which was not effective in immobilising heavy metal via adsorption mechanisms. However, the high pH and ANC of cement paste and lightweight concrete can improve the heavy metal adsorption capacity of soil and soil ANC that help prevents and controls leaching by heavy metals. Copyright © 2017 Elsevier Ltd. All rights reserved.

  13. Children with health impairments by heavy metals in an e-waste recycling area.

    Science.gov (United States)

    Zeng, Xiang; Xu, Xijin; Boezen, H Marike; Huo, Xia

    2016-04-01

    E-waste recycling has become a global environmental health issue. Pernicious chemicals escape into the environment due to informal and nonstandard e-waste recycling activities involving manual dismantling, open burning to recover heavy metals and open dumping of residual fractions. Heavy metals derived from electronic waste (e-waste), such as, lead (Pb), cadmium (Cd), chromium (Cr), manganese (Mn), nickel (Ni), mercury (Hg), arsenic (As), copper (Cu), zinc (Zn), aluminum (Al) and cobalt (Co), differ in their chemical composition, reaction properties, distribution, metabolism, excretion and biological transmission. Our previous studies showed that heavy metal exposure have adverse effects on children's health including lower birth weight, lower anogenital distance, lower Apgar scores, lower current weight, lower lung function, lower hepatitis B surface antibody levels, higher prevalence of attention-deficit/hyperactivity disorder, and higher DNA and chromosome damage. Heavy metals influence a number of diverse systems and organs, resulting in both acute and chronic effects on children's health, ranging from minor upper respiratory irritation to chronic respiratory, cardiovascular, nervous, urinary and reproductive disease, as well as aggravation of pre-existing symptoms and disease. These effects of heavy metals on children's health are briefly discussed. Copyright © 2016 Elsevier Ltd. All rights reserved.

  14. Nonisothermal particle modeling of municipal solid waste combustion with heavy metal vaporization

    Energy Technology Data Exchange (ETDEWEB)

    Mazza, G. [Facultad de Ingenieria, Departamento de Quimica, Universidad Nacional del Comahue, IDEPA (CONICET - UNCo), Buenos Aires 1400, 8300 Neuquen (Argentina); Falcoz, Q.; Gauthier, D.; Flamant, G. [Laboratoire Procedes et Materiaux et Energie Solaire (CNRS-PROMES), 7 Rue du Four Solaire, Odeillo, 66120 Font-Romeu Cedex (France); Soria, J. [Facultad de Ingenieria, Departamento de Quimica, Universidad Nacional del Comahue, IDEPA (CONICET - UNCo), Buenos Aires 1400, 8300 Neuquen (Argentina); Laboratoire Procedes et Materiaux et Energie Solaire (CNRS-PROMES), 7 Rue du Four Solaire, Odeillo, 66120 Font-Romeu Cedex (France)

    2010-12-15

    A particulate model was developed for municipal solid-waste incineration in a fluidized bed combining solid-waste-particle combustion and heavy metal vaporization from the burning particles. Based on a simpler, isothermal version presented previously, this model combines an asymptotic-combustion model for carbonaceous-solid combustion and a shrinking-core model to describe the heavy metal vaporization phenomenon, in which the particle is now considered nonisothermal. A parametric study is presented that shows the influence of temperature on the global metal-vaporization process. The simulation results are compared to experimental data obtained with a lab-scale fluid bed incinerator and to the results of the simpler isothermal model. It is shown that conduction in the particle strongly affects the variation of the vaporization rate with time and that the present version of the model well fits both the shape of the plots and the maximum heavy metal vaporization rates for all bed temperatures. (author)

  15. Study on the behavior of heavy metals during thermal treatment of municipal solid waste (MSW) components.

    Science.gov (United States)

    Yu, Jie; Sun, Lushi; Wang, Ben; Qiao, Yu; Xiang, Jun; Hu, Song; Yao, Hong

    2016-01-01

    Laboratory experiments were conducted to investigate the volatilization behavior of heavy metals during pyrolysis and combustion of municipal solid waste (MSW) components at different heating rates and temperatures. The waste fractions comprised waste paper (Paper), disposable chopstick (DC), garbage bag (GB), PVC plastic (PVC), and waste tire (Tire). Generally, the release trend of heavy metals from all MSW fractions in rapid-heating combustion was superior to that in low-heating combustion. Due to the different characteristics of MSW fractions, the behavior of heavy metals varied. Cd exhibited higher volatility than the rest of heavy metals. For Paper, DC, and PVC, the vaporization of Cd can reach as high as 75% at 500 °C in the rapid-heating combustion due to violent combustion, whereas a gradual increase was observed for Tire and GB. Zn and Pb showed a moderate volatilization in rapid-heating combustion, but their volatilities were depressed in slow-heating combustion. During thermal treatment, the additives such as kaolin and calcium can react or adsorb Pb and Zn forming stable metal compounds, thus decreasing their volatilities. The formation of stable compounds can be strengthened in slow-heating combustion. The volatility of Cu was comparatively low in both high and slow-heating combustion partially due to the existence of Al, Si, or Fe in residuals. Generally, in the reducing atmosphere, the volatility of Cd, Pb, and Zn was accelerated for Paper, DC, GB, and Tire due to the formation of elemental metal vapor. TG analysis also showed the reduction of metal oxides by chars forming elemental metal vapor. Cu2S was the dominant Cu species in reducing atmosphere below 900 °C, which was responsible for the low volatility of Cu. The addition of PVC in wastes may enhance the release of heavy metals, while GB and Tire may play an opposite effect. In controlling heavy metal emission, aluminosilicate- and calcium-based sorbents can be co-treated with fuels. Moreover

  16. Estimation of Pb from metal and electroplating industrial waste by ...

    African Journals Online (AJOL)

    Removal of lead in the sediments and liquid waste was then carried out using zeolite-3A. Result shows the quantitative removal of lead. Factors that effect the lead removal include the adsorbent concentration, pH and temperature. The applicability of Freundlich, Langmuir and Dubinin Radushkevich equations for the ...

  17. Screening of heavy metal containing waste types for use as raw material in Arctic clay-based bricks

    DEFF Research Database (Denmark)

    Belmonte, Louise Josefine; Ottosen, Lisbeth M.; Kirkelund, Gunvor Marie

    2016-01-01

    In the vulnerable Arctic environment, the impact of especially hazardous wastes can have severe consequences and the reduction and safe handling of these waste types are therefore an important issue. In this study, two groups of heavy metal containing particulate waste materials, municipal solid...

  18. Metals control efficiency test at a dry-scrubber and baghouse-equipped hazardous-waste incinerator

    Energy Technology Data Exchange (ETDEWEB)

    Garg, S.; Holloway, J.R.

    1990-09-01

    The Environmental Protection Agency, Office of Solid Waste is developing regulations to control emissions of toxic metals from hazardous waste incinerators. As part of an effort to gather data on control efficiencies that can be achieved by hazardous waste incineration facilities, equipped with various types of air pollution control devices, a test was performed at Unit No. 4 in Sauget, Illinois.

  19. 40 CFR 60.33b - Emission guidelines for municipal waste combustor metals, acid gases, organics, and nitrogen oxides.

    Science.gov (United States)

    2010-07-01

    ..., acid gases, organics, and nitrogen oxides. (a) The emission limits for municipal waste combustor metals... stringent. (c) The emission limits for municipal waste combustor organics, expressed as total mass dioxin... 40 Protection of Environment 6 2010-07-01 2010-07-01 false Emission guidelines for municipal waste...

  20. 40 CFR 60.52b - Standards for municipal waste combustor metals, acid gases, organics, and nitrogen oxides.

    Science.gov (United States)

    2010-07-01

    ... § 60.52b Standards for municipal waste combustor metals, acid gases, organics, and nitrogen oxides. (a... oxygen (dry basis), whichever is less stringent. (c) The limits for municipal waste combustor organics... 40 Protection of Environment 6 2010-07-01 2010-07-01 false Standards for municipal waste combustor...

  1. 40 CFR 62.14103 - Emission limits for municipal waste combustor metals, acid gases, organics, and nitrogen oxides.

    Science.gov (United States)

    2010-07-01

    ... combustor metals, acid gases, organics, and nitrogen oxides. (a) The emission limits for municipal waste... that affected facility any gases that contain municipal waste combustor organics, expressed as total... 40 Protection of Environment 8 2010-07-01 2010-07-01 false Emission limits for municipal waste...

  2. Generation of copper rich metallic phases from waste printed circuit boards.

    Science.gov (United States)

    Cayumil, R; Khanna, R; Ikram-Ul-Haq, M; Rajarao, R; Hill, A; Sahajwalla, V

    2014-10-01

    The rapid consumption and obsolescence of electronics have resulted in e-waste being one of the fastest growing waste streams worldwide. Printed circuit boards (PCBs) are among the most complex e-waste, containing significant quantities of hazardous and toxic materials leading to high levels of pollution if landfilled or processed inappropriately. However, PCBs are also an important resource of metals including copper, tin, lead and precious metals; their recycling is appealing especially as the concentration of these metals in PCBs is considerably higher than in their ores. This article is focused on a novel approach to recover copper rich phases from waste PCBs. Crushed PCBs were heat treated at 1150°C under argon gas flowing at 1L/min into a horizontal tube furnace. Samples were placed into an alumina crucible and positioned in the cold zone of the furnace for 5 min to avoid thermal shock, and then pushed into the hot zone, with specimens exposed to high temperatures for 10 and 20 min. After treatment, residues were pulled back to the cold zone and kept there for 5 min to avoid thermal cracking and re-oxidation. This process resulted in the generation of a metallic phase in the form of droplets and a carbonaceous residue. The metallic phase was formed of copper-rich red droplets and tin-rich white droplets along with the presence of several precious metals. The carbonaceous residue was found to consist of slag and ∼30% carbon. The process conditions led to the segregation of hazardous lead and tin clusters in the metallic phase. The heat treatment temperature was chosen to be above the melting point of copper; molten copper helped to concentrate metallic constituents and their separation from the carbonaceous residue and the slag. Inert atmosphere prevented the re-oxidation of metals and the loss of carbon in the gaseous fraction. Recycling e-waste is expected to lead to enhanced metal recovery, conserving natural resources and providing an environmentally

  3. Separation of tc from Uranium and development of metallic Technetium waste forms

    Science.gov (United States)

    Mausolf, Edward John

    The isotope Technetium-99 (99Tc) is a major fission product of the nuclear industry. In the last decade, approximately 20 tons of 99Tc have been produced by the US nuclear industry. Due to its long half-life (t1/2 = 214,000 yr), beta radiotoxicity, and high mobility as pertechnetate [TcO4]-, Tc represents long-term concern to the biosphere. Various options have been considered to manage 99Tc. One of them is its separation from spent fuel, conversion to the metal and incorporation into a metallic waste form for long-term disposal. After dissolution of spent fuel in nitric acid and extraction of U and Tc in organic media, previously developed methods can be used to separate Tc from U, convert the separate Tc stream to the metal and reuse the uranium component of the fuel. A variety of metallic waste forms, ranging from pure Tc metal to ternary Tc alloys combined with stainless steel (SS) and Zr are proposed. The goal of this work was to examine three major questions: What is the optimal method to separate Tc from U? After separation, what is the most efficient method to convert the Tc stream to Tc metal? Finally, what is the corrosion behavior of Tc metal, Tc-SS alloys and Tc-Zr-SS alloys in 0.01M NaCl? The goal is to predict the long term behavior of Tc metallic waste in a hypothetical storage environment. In this work, three methods have been used to separate Tc from U: anionic exchange resin, liquid-liquid extraction and precipitation. Of the three methods studied, anionic exchange resins is the most selective. After separation of Tc from U, three different methods were studied to convert the Tc stream to the metal: thermal treatment under hydrogen atmosphere, electrochemical and chemical reduction of pertechnetate in aqueous media. The thermal treatment of the Tc stream under hydrogen atmosphere is the preferred method to produce Tc metal. After Tc metal is isolated, it will be incorporated into a metal host phase. Three different waste forms were produced for

  4. Recovery of metallic concentrations from waste printed circuit boards via reverse floatation.

    Science.gov (United States)

    He, Jingfeng; Duan, Chenlong

    2017-02-01

    Efficient disposal of waste printed circuit boards (PCBs) is favorable toward recovering valuable components and reducing pollution. Reverse floatation was used to recover metallic concentrations from waste PCBs. Basic properties and mineralogical characteristics of raw PCBs were tested and analyzed. Results indicated that the grade of metallic concentrations declined as the size fraction of PCBs decreased. The major metallic elements found in PCBs were Cu, Pb, and Sn, as well as trace elements were also found in fine PCB particles. Kerosene and terpenic oil were used as the collector and frother in the floatation experiments. The effects of various operational factors, including the feeding concentration, aeration rate, and agitation speed of floatation machine, on the floatation performance of -0.25mm PCBs were experimentally studied to determine optimal range. The floatation results suggested that the yield of sinks and grade of metallic concentrations diminished significantly with the decrease of size fraction of PCBs. The maximum yields of sinks and highest grades of metallic concentrations were 48.72% and 16.86%, 47.96% and 14.61%, 44.36% and 8.81%, with the optimum recoveries of metallic concentrations of 94.69%, 90.06%, and 75.96% for size fractions of 0.125-0.25mm, 0.074-0.125mm, and -0.074mm PCBs, respectively. The recovery efficiency of metallic concentrations declined as the size fraction decreased. The efficient overall recovery performance of metallic concentrations from waste PCBs was obtained via reverse floatation. This study provides an alternative approach for disposing waste PCBs. Copyright © 2016 Elsevier Ltd. All rights reserved.

  5. [Correlation of Persistent Free Radicals, PCDD/Fs and Metals in Waste Incineration Fly Ash].

    Science.gov (United States)

    Wang, Tian-jiao; Chen, Tong; Zhan, Ming-xiu; Guo, Ying; Li, Xiao-dong

    2016-03-15

    Environmentally persistent free radicals (EPFRs) are relatively highly stable and found in the formation of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs). Recent studies have concentrated on model dioxin formation reactions and there are few studies on actual waste incineration fly ash. In order to study EPFRs and the correlation with dioxins and heavy metals in waste incineration fly ash, the spins of EPFRs, concentration of PCDD/Fs and metals in samples from 6 different waste incinerators were detected. The medical waste incineration fly ash from Tianjin, municipal solid waste incineration fly ash from Jiangxi Province, black carbon and slag from municipal solid waste incinerator in Lanxi, Zhejiang Province, all contained EPFRs. Above all the signal in Tianjin sample was the strongest. Hydroxyl radicals, carbon-center radicals and semiquinone radicals were detected. Compared with other samples, Jiangxi fly ash had the highest toxic equivalent quantity (TEQ) of dioxins, up to 7.229 4 ng · g⁻¹. However, the dioxin concentration in the Tianjin sample containing the strongest EPFR signals was only 0.092 8 ng · g⁻¹. There was perhaps little direct numeric link between EPFRs and PCDD/Fs. But the spins of EPFRs in samples presented an increasing trend as the metal contents increased, especially with Al, Fe, Zn. The signal strength of radicals was purposed to be related to the metal contents. The concentration of Zn (0.813 7% ) in the Tianjin sample was the highest and this sample contained much more spins of oxygen-center radicals. We could presume the metal Zn had a greater effect on the formation of EPFRs, and was easier to induce the formation of radicals with a longer half-life period.

  6. Qualitative and quantitative metals liberation assessment for characterization of various waste printed circuit boards for recycling.

    Science.gov (United States)

    Priya, Anshu; Hait, Subrata

    2017-12-01

    Metals liberation and composition are decisive attributes in characterization of e-waste for metal recycling. Though end-of-life printed circuit board (PCB) is an integral part of e-waste as secondary resource reservoir, yet no standardized procedure exists for metals liberation and dissolution for its characterization. Thus, the paper aims at assessment of metals liberation upon comminution employing scanning electron microscopy with energy dispersive X-ray spectroscopy (SEM-EDS) followed by comparative assessment of the existing United States Environmental Protection Agency (USEPA) digestion procedures, viz., USEPA 3050B, USEPA 3051A, and USEPA 3052, in effective dissolution of metals from comminuted particles of waste PCBs of computer, laptop, mobile phone, and television. Effect of comminution and digestion conditions was assessed to have significant role in metal liberation and dissolution from PCBs. The SEM-EDS analysis demonstrated partial release of metals from the silica matrix of PCBs. The USEPA digestion methods showed statistically significant (P < 0.05) difference with greater dissolution of metals complexed to PCB matrix by the USEPA 3052 method owing to use of strong acid like hydrofluoric acid. Base metals like Cu and Zn and toxic metals such as Pb and Cd were present in abundance in PCBs and in general exceeded the total threshold limit concentration (TTLC). The maximum contents of Cu (20.13 ± 0.04 wt.%) and Zn (1.89 ± 0.05 wt.%) in laptop PCBs, Pb (2.26 ± 0.08 wt.%) in TV PCBs, and Cd (0.0812 ± 0.0008 wt.%) in computer PCBs were observed.

  7. Selective dissolution followed by EDDS washing of an e-waste contaminated soil: Extraction efficiency, fate of residual metals, and impact on soil environment.

    Science.gov (United States)

    Beiyuan, Jingzi; Tsang, Daniel C W; Valix, Marjorie; Zhang, Weihua; Yang, Xin; Ok, Yong Sik; Li, Xiang-Dong

    2017-01-01

    To enhance extraction of strongly bound metals from oxide minerals and organic matter, this study examined the sequential use of reductants, oxidants, alkaline solvents and organic acids followed by a biodegradable chelating agent (EDDS, [S,S]-ethylene-diamine-disuccinic-acid) in a two-stage soil washing. The soil was contaminated by Cu, Zn, and Pb at an e-waste recycling site in Qingyuan city, China. In addition to extraction efficiency, this study also examined the fate of residual metals (e.g., leachability, bioaccessibility, and distribution) and the soil quality parameters (i.e., cytotoxicity, enzyme activities, and available nutrients). The reductants (dithionite-citrate-bicarbonate and hydroxylamine hydrochloride) effectively extracted metals by mineral dissolution, but elevated the leachability and bioaccessibility of metals due to the transformation from Fe/Mn oxides to labile fractions. Subsequent EDDS washing was found necessary to mitigate the residual risks. In comparison, prior washing by oxidants (persulphate, hypochlorite, and hydrogen peroxide) was marginally useful because of limited amount of soil organic matter. Prior washing by alkaline solvents (sodium hydroxide and sodium bicarbonate) was also ineffective due to metal precipitation. In contrast, prior washing by low-molecular-weight organic acids (citrate and oxalate) improved the extraction efficiency. Compared to hydroxylamine hydrochloride, citrate and oxalate induced lower cytotoxicity (Microtox) and allowed higher enzyme activities (dehydrogenase, acid phosphatase, and urease) and soil nutrients (available nitrogen and phosphorus), which would facilitate reuse of the treated soil. Therefore, while sequential washing proved to enhance extraction efficacy, the selection of chemical agents besides EDDS should also include the consideration of effects on metal leachability/bioaccessibility and soil quality. Copyright © 2016 Elsevier Ltd. All rights reserved.

  8. Leaching studies for metals recovery from waste printed wiring boards

    Science.gov (United States)

    Luyima, Alex; Shi, Honglan; Zhang, Lifeng

    2011-08-01

    The leaching behavior of most metals present in printed wiring boards is evaluated, aiming at its recycling by hydrometallurgy. Two leaching reagents (nitric acid and aqua regia) are compared. The effects of acid concentration, particle size of sample, leaching time, and temperature are examined. The results reveal that small particle size and a combination of both nitric acid and aqua regia are capable of dissolving most of the metals content of printed wiring boards.

  9. Adsorption of valuable metals from leachates of mobile phone wastes using biopolymers and activated carbon.

    Science.gov (United States)

    Zazycki, Maria A; Tanabe, Eduardo H; Bertuol, Daniel A; Dotto, Guilherme L

    2017-03-01

    In this work, chitin (CTN), chitosan (CTS) and activated carbon (AC) were used as adsorbents to recover valuable metals from leachates of mobile phone wastes. The mobile phone wastes (contactors) were collected and characterized. The valuable metals were extracted by thiourea leaching. The adsorption of valuable metals from leachates was studied according to the kinetic and equilibrium viewpoints. It was found that the contactors were composed by Au, Ni, Cu and Sn. The thiourea leaching provided extraction percentages of 68.6% for Au, 22.1% for Ni and 2.8% for Cu. Sn was not extracted. The leachate presented 17.5 mg L-1 of Au, 324.9 mg L-1 of Ni and 573.1 mg L-1 of Cu. The adsorption was fast, being the equilibrium attained within 120 min. The adsorption of Au, Ni and Cu onto CTN and AC followed the Langmuir model, while, the adsorption of these metals onto CTS, followed the Freundlich model. Removal percentages higher than 95% were obtained for all metals, depending of the type and amount of adsorbent. It was demonstrated that the adsorption onto chitin, chitosan and activated carbon can be an alternative to recover valuable metals from leachates of mobile phone wastes. Copyright © 2016 Elsevier Ltd. All rights reserved.

  10. Metal concentrations and distribution in paint waste generated during bridge rehabilitation in New York State.

    Science.gov (United States)

    Shu, Zhan; Axe, Lisa; Jahan, Kauser; Ramanujachary, Kandalam V; Kochersberger, Carl

    2015-09-01

    Between 1950 and 1980, lead and chromium along with other metals have been used in paint coatings to protect bridges from corrosion. In New York State with 4500 bridges in 11 Regions 2385 of the bridges have been rehabilitated and subsequently repainted after 1989 when commercial use of lead based paint was prohibited. The purpose of this research was to address the concentration and distribution of trace metals in the paint waste generated during bridge rehabilitation. Using hypothesis testing and stratified sampling theory, a representative sample size of 24 bridges from across the state was selected that resulted in 117 paint waste samples. Field portable X-ray fluorescence (FP-XRF) analysis revealed metal concentrations ranged from 5 to 168,090 mg kg(-1) for Pb, 49,367 to 799,210 mg kg(-1) for Fe, and 27 to 425,510 mg kg(-1) for Zn. Eighty percent of the samples exhibited lead concentrations greater than 5000 mg kg(-1). The elevated iron concentrations may be attributed to the application of steel grit as an abrasive blasting material routinely used by state Departments of Transportation in the paint removal process. Other metals including Ba and Cr were observed in the paint waste as well. As a result of the paint formulation, metals were found to be associated in the paint waste (Pb correlated with Cr (r=0.85)). The elevated metal concentrations observed raises concern over the potential impact of leaching from this waste stream. Copyright © 2015 Elsevier B.V. All rights reserved.

  11. Metals recovering from waste printed circuit boards (WPCBs) using molten salts

    Energy Technology Data Exchange (ETDEWEB)

    Flandinet, L. [LEPMI, UMR 5279, CNRS - Grenoble INP-Universite de Savoie, Universite Joseph Fourier, BP75, 38402 Saint Martin d' Heres (France); Tedjar, F. [LEPMI, UMR 5279, CNRS - Grenoble INP-Universite de Savoie, Universite Joseph Fourier, BP75, 38402 Saint Martin d' Heres (France); RECUPYL SA, Rue de la metallurgie 38420 Domene (France); Ghetta, V. [LPSC, UJF Grenoble 1 - CNRS/IN2P3 - INPG, 53 rue des Martyrs 38026 Grenoble Cedex (France); Fouletier, J., E-mail: Jacques.Fouletier@lepmi.grenoble-inp.fr [LEPMI, UMR 5279, CNRS - Grenoble INP-Universite de Savoie, Universite Joseph Fourier, BP75, 38402 Saint Martin d' Heres (France)

    2012-04-30

    Highlights: Black-Right-Pointing-Pointer Recovering of valuable metals from WPCBs. Black-Right-Pointing-Pointer Low temperature treatment, i.e., 300 Degree-Sign C. Black-Right-Pointing-Pointer Copper, and precious metals are recovered, without dissolution or melting. Black-Right-Pointing-Pointer Many hazardous gases are dissolved and trapped in the molten salt. Black-Right-Pointing-Pointer Under operation without oxygen the flue gas contains large quantities of hydrogen. - Abstract: Recycling of waste electrical and electronic equipments (WEEE) has been taken into consideration in the literature due to the large quantity of concerned wastes and their hazardous contents. The situation is so critical that EU published European Directives imposing collection and recycling with a minimum of material recovery . Moreover, WEEEs contain precious metals, making the recycling of these wastes economically interesting, but also some critical metals and their recycling leads to resource conservation. This paper reports on a new approach for recycling waste printed circuit boards (WPCBs). Molten salts and specifically molten KOH-NaOH eutectic is used to dissolve glasses, oxides and to destruct plastics present in wastes without oxidizing the most valuable metals. This method is efficient for recovering a copper-rich metallic fraction, which is, moreover, cleared of plastics and glasses. In addition, analyses of gaseous emission show that this method is environmentally friendly since most of the process gases, such as carbon monoxide and dioxide and halogens, are trapped in the highly basic molten salt. In other respects, under operation without oxygen, a large quantity of hydrogen is produced and might be used as fuel gas or as synthesis gas, leading to a favourable energy balance for this new process.

  12. Mitigation of Hydrogen Gas Generation from the Reaction of Uranium Metal with Water in K Basin Sludge and Sludge Waste Forms

    Energy Technology Data Exchange (ETDEWEB)

    Sinkov, Sergey I.; Delegard, Calvin H.; Schmidt, Andrew J.

    2011-06-08

    Prior laboratory testing identified sodium nitrate and nitrite to be the most promising agents to minimize hydrogen generation from uranium metal aqueous corrosion in Hanford Site K Basin sludge. Of the two, nitrate was determined to be better because of higher chemical capacity, lower toxicity, more reliable efficacy, and fewer side reactions than nitrite. The present lab tests were run to determine if nitrate’s beneficial effects to lower H2 generation in simulated and genuine sludge continued for simulated sludge mixed with agents to immobilize water to help meet the Waste Isolation Pilot Plant (WIPP) waste acceptance drainable liquid criterion. Tests were run at ~60°C, 80°C, and 95°C using near spherical high-purity uranium metal beads and simulated sludge to emulate uranium-rich KW containerized sludge currently residing in engineered containers KW-210 and KW-220. Immobilization agents tested were Portland cement (PC), a commercial blend of PC with sepiolite clay (Aquaset II H), granulated sepiolite clay (Aquaset II G), and sepiolite clay powder (Aquaset II). In all cases except tests with Aquaset II G, the simulated sludge was mixed intimately with the immobilization agent before testing commenced. For the granulated Aquaset II G clay was added to the top of the settled sludge/solution mixture according to manufacturer application directions. The gas volumes and compositions, uranium metal corrosion mass losses, and nitrite, ammonia, and hydroxide concentrations in the interstitial solutions were measured. Uranium metal corrosion rates were compared with rates forecast from the known uranium metal anoxic water corrosion rate law. The ratios of the forecast to the observed rates were calculated to find the corrosion rate attenuation factors. Hydrogen quantities also were measured and compared with quantities expected based on non-attenuated H2 generation at the full forecast anoxic corrosion rate to arrive at H2 attenuation factors. The uranium metal

  13. Assessment of Waste Production and Heavy Metal Emission from Energy Production Sector of Zahedan City

    Directory of Open Access Journals (Sweden)

    Nayyere Poormollae

    2013-12-01

    Full Text Available Background and purpose: Due to the lack of accurate statistics on the amount of waste generated in the energy production sector in Zahedan, before any planning, one should identify all waste producing centers associated with the energy sector and also the quantity and quality of their waste in Zahedan. Materials and methods: This research is a cross-sectional descriptive study. It examined the produced wastes in the electrical energy generation sector. A questionnaire was prepared and completed for each unit that possibility produces these wastes. Moreover, in the studied units, the weigh percent per unit was determined by separating production waste, and collecting and weighing them. Results: In gas power plant of Zahedan, production of burned oil was approximately 480 liters and the annual consumption of turbine oil and compressor oil was 40 liters. In the diesel power plant, 2,200 liters of burned oil is produced for each generator after 1,500 hours of work. Concentration of heavy metals of Cr, Cd, Zn, Pb, Cu, and Ni in the burned oil sample of the gas power plant was 43.2, 0.01, 0.20, 1.3, 2.7, 0.2 mg/l, respectively and in the diesel power plant were 36.3, 0.08, 0.09, 0.9, 4.7, 1.1 mg/l. Conclusion: In the studied samples, several cases of heavy metal pollution were identified. Therefore, proper planning for appropriate management of these units is necessary for any possible leakage and environmental pollution transport. Furthermore, in order to minimize the adverse impacts of hazardous wastes on the environment and people in Zahedan, integrated hazardous wastes management should be practices in electrical energy generation plants. Moreover, one must consider the measures required to exposure, transport, and safe maintenance before managing or eliminating this type of waste.

  14. Economic evaluation of an electrochemical process for the recovery of metals from electronic waste.

    Science.gov (United States)

    Diaz, Luis A; Lister, Tedd E

    2017-12-08

    As the market of electronic devices continues to evolve, the waste stream generated from antiquated technology is increasingly view as an alternative to substitute primary sources of critical a value metals. Nevertheless, the sustainable recovery of materials can only be achieved by environmentally friendly processes that are economically competitive with the extraction from mineral ores. Hence, This paper presents the techno-economic assessment for a comprehensive process for the recovery of metals and critical materials from e-waste, which is based in an electrochemical recovery (ER) technology. Economic comparison is performed with the treatment of e-waste via smelting, which is currently the primary route for recycling metals from electronics. Results indicate that the electrochemical recovery process is a competitive alternative for the recovery of value from electronic waste when compared with the traditional black Cu smelting process. A significantly lower capital investment, 2.9 kg e-waste per dollar of capital investment, can be achieved with the ER process vs. 1.3 kg per dollar in the black Cu smelting process. Copyright © 2017 Elsevier Ltd. All rights reserved.

  15. Vaporization of heavy metals during thermal treatment of model solid waste in a fluidized bed incinerator.

    Science.gov (United States)

    Yu, Jie; Sun, Lushi; Xiang, Jun; Hu, Song; Su, Sheng; Qiu, Jianrong

    2012-03-01

    This paper investigated the volatilization behavior of heavy metals during thermal treatment of model solid waste in a fluidized bed reactor. Four metal chlorides (Cd, Pb, Cu and Zn) were chosen as metal sources. The influence of redox conditions, water and mineral matrice on heavy metal volatilization was investigated. In general, Cd shows significant vaporization especially when HCl was injected, while Cu and Pb vaporize moderately and Zn vaporization is negligible. Increasing oxygen concentration can lower heavy metal vaporization. Heavy metal interactions with the mineral matter can result in the formation of stable metallic species thus playing a negative effect on their behavior. However, HCl can promote the heavy metal release by preventing the formation of stable metallic species. The chemical sorption (either physical or chemical) inside the pores, coupled with the internal diffusion of gaseous metal species, may also control the vaporization process. With SO(2) injected, Cd and Pb show a higher volatility as a result of SO(2) reducing characteristics. From the analysis, the subsequent order of heavy metal volatility can be found: Cd>Cu≥Pb≫Zn. Copyright © 2012 Elsevier Ltd. All rights reserved.

  16. Isolation of Metals from Liquid Wastes: Reactive Scavenging by Sorbets in Turbulent Reactors

    Energy Technology Data Exchange (ETDEWEB)

    Wendt, Jost O.L.; Kerstein, Alan R.; Linak, William P.; Pearlstein, Arne J.; Scheeline, Alexander

    2001-06-01

    The objective of this work is to develop the fundamental knowledge base for the design of a broad class of high-temperature reactive capture processes to treat metals-bearing liquid waste in the DOE inventory. The major thrust is devoted to understanding phenomena that govern process performance and are critical to achieving emission specifications.

  17. Autoclave reduction of jarosites and other metal sulfates : a new approach to major waste problems

    NARCIS (Netherlands)

    Hage, J.L.T.

    1999-01-01

    Industrial jarosite is a waste product of the zinc industry. It is considered a serious environmental problem, due to the quantity produced and the mobile hazardous metals it contains. Over 50 million tons are already stored worldwide. The jarosite sludge autoclave treatment process described in

  18. Survey the Effect of Pistachio Waste Composting Process with Different Treatments on Concentration of Heavy Metals

    Directory of Open Access Journals (Sweden)

    M Jalili

    2016-09-01

    Full Text Available Abstract Introduction: Composting is one of the pistachio wastes management methods. In the appropriate compost production nutrients and heavy metals are determinant. The aim of this study is survey the effect of pistachio wastes composting process with different treatments on the concentration of heavy metals. Methods: In this study, during the 60-day pistachio wastes composting process with two treatments of dewatered sewage sludge and cow manure, pH, EC, carbon to nitrogen ratio, Heavy metals and nutrients indicators were studied. The results were compared with WHO and Iranian National standard. Drawing the diagrams by Excel software (Version 2007 and Statistical analysis was performed by Spss Software (version 20 at a significance level of 0.005.  Results: During the 60-day composting pH initially had downward trend and then increased. The Cu, Zn, Fe, Mn and C/N ratio had downward trend and the EC, Na, K had increasing trend. Eventually, Iron, zinc, copper and manganese were less than the standard, Sodium was in Standard range and potassium was more than specified standards in the produced compost from pistachios waste with both treatments.  Conclusion: The results showed that the concentration of heavy metals and nutrients in the produced compost with both treatments were in the acceptable range. Eventually quality of produced compost with cow manure treatment due to better decomposition and greater stability was better than processed compost with dewatered sewage sludge treatment.

  19. Recovery of precious metals from waste materials by the method of flotation process

    Directory of Open Access Journals (Sweden)

    B. Oleksiak

    2013-01-01

    Full Text Available The article presents the investigation results upon recovery of precious metals from electronics waste and used ceramic catalytic converters. Various frothing agents which generate stable and abundant foam as well as collectors and pH regulators have been used in the investigations. The tests were conducted with the use of laboratory flotation device.

  20. Potential resource and toxicity impacts from metals in waste electronic devices.

    Science.gov (United States)

    Woo, Seung H; Lee, Dae Sung; Lim, Seong-Rin

    2016-04-01

    As a result of the continuous release of new electronic devices, existing electronic devices are quickly made obsolete and rapidly become electronic waste (e-waste). Because e-waste contains a variety of metals, information about those metals with the potential for substantial environmental impact should be provided to manufacturers, recyclers, and disposers to proactively reduce this impact. This study assesses the resource and toxicity (i.e., cancer, noncancer, and ecotoxicity) potentials of various heavy metals commonly found in e-waste from laptop computers, liquid-crystal display (LCD) monitors, LCD TVs, plasma TVs, color cathode ray tube (CRT) TVs, and cell phones and then evaluates such potentials using life cycle impact-based methods. Resource potentials derive primarily from Cu, Sb, Ag, and Pb. Toxicity potentials derive primarily from Pb, Ni, and Hg for cancer toxicity; from Pb, Hg, Zn, and As for noncancer toxicity; and from Cu, Pb, Hg, and Zn for ecotoxicity. Therefore, managing these heavy metals should be a high priority in the design, recycling, and disposal stages of electronic devices. © 2015 SETAC.

  1. Removal of heavy metal contamination from peanut skin extracts by waste biomass adsorption

    Science.gov (United States)

    Polyphenols are a rapidly increasing portion of the nutraceutical and functional food marketplace. Peanut skins are a waste product which have potential as a low-cost source of polyphenols. Extraction and concentration of peanut skin extracts can cause normally innocuous levels of the heavy metal co...

  2. Initial soil development under pioneer plant species in metal mine waste deposits

    NARCIS (Netherlands)

    Arocena, J.M.; van Mourik, J.M.; Schilder, M.L.M.; Faz Cano, A.

    2010-01-01

    Mine waste materials are often inhospitable to plants due to extreme pH, high salinity, very low organic matter, elevated metal contents, and poor physical conditions. We investigated initial soil development in three study areas under different pioneer plant species in degraded landscapes left

  3. Heavy metal contamination of surface soil in electronic waste dismantling area: site investigation and source-apportionment analysis.

    Science.gov (United States)

    Jinhui Li; Huabo Duan; Pixing Shi

    2011-07-01

    The dismantling and disposal of electronic waste (e-waste) in developing countries is causing increasing concern because of its impacts on the environment and risks to human health. Heavy-metal concentrations in the surface soils of Guiyu (Guangdong Province, China) were monitored to determine the status of heavy-metal contamination on e-waste dismantling area with a more than 20 years history. Two metalloids and nine metals were selected for investigation. This paper also attempts to compare the data among a variety of e-waste dismantling areas, after reviewing a number of heavy-metal contamination-related studies in such areas in China over the past decade. In addition, source apportionment of heavy metal in the surface soil of these areas has been analysed. Both the MSW open-burning sites probably contained invaluable e-waste and abandoned sites formerly involved in informal recycling activities are the new sources of soil-based environmental pollution in Guiyu. Although printed circuit board waste is thought to be the main source of heavy-metal emissions during e-waste processing, requirement is necessary to soundly manage the plastic separated from e-waste, which mostly contains heavy metals and other toxic substances.

  4. Experimental design and process analysis for acidic leaching of metal-rich glass wastes.

    Science.gov (United States)

    Tuncuk, A; Ciftci, H; Akcil, A; Ognyanova, A; Vegliò, F

    2010-05-01

    The removal of iron, titanium and aluminium from colourless and green waste glasses has been studied under various experimental conditions in order to optimize the process parameters and to decrease the metal content in the waste glass by acidic leaching. Statistical design of experiments and ANOVA (analysis of variance) were performed in order to determine the main effects and interactions between the investigated factors (sample ratio, acid concentration, temperature and leaching time). A full factorial experiment was performed by sulphuric acid leaching of glass for metal removal. After treating, the iron content was 530 ppm, corresponding to 1880 ppm initial concentration of Fe(2)O(3) in the original colourless sample. This result is achieved using 1M H(2)SO( 4) and 30% sample ratio at 90(o)C leaching temperature for 2 hours. The iron content in the green waste glass sample was reduced from 3350 ppm initial concentration to 2470 ppm after treating.

  5. Concentrating precious metals from ash and slag waste of Far Eastern energy enterprises

    Science.gov (United States)

    Taskin, A. V.; Ivannikov, I. S.; Danilov, O. S.

    2017-10-01

    This work represents the data on the content of gold, noble metals and rare earth metals in ash and slag waste taken from the ash disposal areas of the Far Eastern energy enterprises. Ash and slag objects with increased concentration of Au and Ag were found. The chemical content of samples from researched ash and slag disposal areas is represented in this work. A scheme of dividing ash and slag waste into different mineral fractions is offered in this work. The mechanisms of collecting and distribution of Au, Pt and Ag concentrations in ash and slag wastes were determined during the research. Also, the possibility of gold concentration in heavy non-magnetic fraction is shown.

  6. Development of Ceramic Coating on Metal Substrate using Industrial Waste and Ore Minerals

    Science.gov (United States)

    Bhuyan, S. K.; Thiyagarajan, T. K.; Mishra, S. C.

    2017-02-01

    The technological advancement in modern era has a boon for enlightening human life; but also is a bane to produce a huge amount of (industrial) wastes, which is of great concern for utilization and not to create environmental threats viz. polution etc. In the present piece of research work, attempts have been made to utilize fly ash (wastes of thermal power plants) and along with alumina bearing ore i.e. bauxite, for developing plasma spray ceramic coatings on metals. Fly ash and with 10 and 20% bauxite addition is used to deposit plasma spray coatings on a metal substrate. The surface morphology of the coatings deposited at different power levels of plasma spraying investigated through SEM and EDS analysis. The coating thickness is measured. The porosity levels of the coatings are evaluated. The coating hardness isalso measured. This piece of research work will be beneficial for future development and use of industrial waste and ore minerals for high-valued applications.

  7. New Engineering Solutions in Creation of Mini-BOF for Metallic Waste Recycling

    Science.gov (United States)

    Eronko, S. P.; Gorbatyuk, S. M.; Oshovskaya, E. V.; Starodubtsev, B. I.

    2017-12-01

    New engineering solutions used in design of the mini melting unit capable of recycling industrial and domestic metallic waste with high content of harmful impurities are provided. High efficiency of the process technology implemented with its use is achieved due to the possibility of the heat and mass transfer intensification in the molten metal bath, controlled charge into it of large amounts of reagents in lumps and in fines, and cut-off of remaining process slag during metal tapping into the teeming ladle.

  8. Heavy Metal Leaching as Affected by Long-Time Organic Waste Fertilizer Application.

    Science.gov (United States)

    Lekfeldt, Jonas Duus Stevens; Holm, Peter E; Kjærgaard, Charlotte; Magid, Jakob

    2017-07-01

    The recycling of urban waste products as fertilizers in agriculture may introduce contaminants such as heavy metals into soil that may leach and contaminate groundwater. In the present study, we investigated the leaching of heavy metals from intact soil cores collected in the long-term agricultural field trial CRUCIAL. At the time of sampling, the equivalent of >100 yr of urban waste fertilizers following Danish legislation had been applied. The leaching of Cu was significantly increased in the treatments receiving organic waste products compared with the unfertilized control but remained below the permissible level following Danish drinking water guidelines. The leaching of Cu was controlled primarily by the topsoil Cu content and by the leaching of dissolved organic carbon (DOC) but at the same time significantly correlated with leaching of colloids in soils that had not received fertilizer or had received an organic fertilizer with a low concentration of Cu. The leaching of Zn, Cd, and Co was not significantly increased in urban waste-fertilized treatments. The leaching of Mo was elevated in accelerated waste treatments (both agricultural and urban), and the leaching of Mo was linked to the leaching of DOC. Since leaching of Cr and Pb was strongly linked to the level of colloid leaching, leaching of these metals was reduced in the urban waste treatments. Overall, the results presented should not raise concern regarding the agricultural use of urban waste products in agriculture as long as the relevant guidelines are followed. Copyright © by the American Society of Agronomy, Crop Science Society of America, and Soil Science Society of America, Inc.

  9. Speciation and leaching of trace metal contaminants from e-waste contaminated soils.

    Science.gov (United States)

    Cui, Jin-Li; Luo, Chun-Ling; Tang, Chloe Wing-Yee; Chan, Ting-Shan; Li, Xiang-Dong

    2017-05-05

    Primitive electrical and electronic waste (e-waste) recycling activities have caused serious environmental problems. However, little is known about the speciation and leaching behaviors of metal contaminants at e-waste contaminated sites. This study investigated trace metal speciation/mobilization from e-waste polluted soil through column leaching experiments involving irrigation with rainwater for almost 2.5 years. Over the experimental period, Cu and Zn levels in the porewater were 0.14±0.08mg/L, and 0.16±0.08mg/L, respectively, increasing to 0.33±0.16mg/L, and 0.69±0.28mg/L with plant growth. The amounts of Cu, Zn, and Pb released in surface soil (0-2cm) contributed 43.8%, 22.5%, and 13.8%, respectively, to the original levels. The released Cu and Zn were primarily caused by the mobilization of the carbonate species of metals, including Cu(OH) 2 , CuCO 3 , and Zn 5 (CO 3 ) 2 (OH) 6 , and amorphous Fe/Mn oxides associated fractions characterized by sequential extraction coupling with X-ray absorption spectroscopy. During the experiments, trace metals were not detected in the effluent, and the re-sequestration of trace metals was mainly attributed to the adsorption on the abundant Fe/Mn oxides in the sub-layer soil. This study quantitatively elucidated the molecular speciation of Cu and Zn in e-waste contaminated soil during the column leaching process. Copyright © 2017 Elsevier B.V. All rights reserved.

  10. Leaching of gold, silver and accompanying metals from circuit boards (PCBs waste

    Directory of Open Access Journals (Sweden)

    Jana Ficeriová

    2011-12-01

    Full Text Available Au-Ag noble metal wastes represent a wide range of waste types and forms, with various accompanying metallic elements.The presented leaching strategy for Au-Ag contained in circuit boards (PCBs aims at gaining gold and silver in the metallic form.Application of the proposed ammonium thiosulphate leaching process for the treatment of the above mentioned Au-Ag containing wastesrepresents a practical, economic and at the same time an ecological solution. The ammonium thiosulphate based leaching of gold and silverfrom PCBs waste, using crushing as a pretreatment, was investigated. It was possible to achieve 98 % gold and 93 % silver recovery within48 hours of ammonium thiosulphate leaching. This type of leaching is a better leaching procedure for recovery of gold and silver from PCBwaste than the classical toxic cyanide leaching. 84 % Cu, 82 % Fe, 77 % Al, 76 % Zn, 70 % Ni, 90 % Pd, 88 % Pb and 83 % Sn recovery ofthe accompanying metals was achieved, using sulphuric acid with hydrogen peroxide, sodium chloride and aqua regia. A four steps leachingprocess gave a very satisfactory yield and a more rapid kinetics for all observed metals solubilization than other technologies.

  11. Metal uptake by native plants and revegetation potential of mining sulfide-rich waste-dumps.

    Science.gov (United States)

    Gomes, Patrícia; Valente, Teresa; Pamplona, Jorge; Braga, Maria Amália Sequeira; Pissarra, José; Gil, José António Grande; de la Torre, Maria Luisa

    2014-01-01

    Waste dumps resulting from metal exploitation create serious environmental damage, providing soil and water degradation over long distances. Phytostabilization can be used to remediate these mining sites. The present study aims to evaluate the behavior of selected plant species (Erica arborea, Ulex europaeus, Agrostis delicatula, and Cytisus multiflorus) that grow spontaneously in three sulfide-rich waste-dumps (Lapa Grande, Cerdeirinha, and Penedono, Portugal). These sites represent different geological, climatic and floristic settings. The results indicate distinctive levels and types of metal contamination: Penedono presents highest sulfate and metal contents, especially As, with low levels of Fe. In contrast, at Lapa Grande and Cerdeirinha Fe, Mn, and Zn are the dominant metals. In accordance, each waste dump develops a typical plant community, providing a specific vegetation inventory. At Penedono, Agrostis delicatula accumulates As, Pb, Cu, Mn, and Zn, showing higher bioaccumulation factors (BF) for Mn (32.1) and As (24.4). At Cerdeirinha, Ulex europaeus has the highest BF for Pb (984), while at Lapa Grande, Erica arborea presents high BF for Mn (9.8) and Pb (8.1). Regarding TF, low values were obtained for most of the metals, especially As (TF < 1). Therefore, the results obtained from representative plant species suggest appropriate behavior for phytostabilization measures.

  12. Heavy metals pollution at municipal solid waste dumpsites in Kano ...

    African Journals Online (AJOL)

    Soil samples collected from two major dumpsites each in Kano and Kaduna states were investigated for heavy metals pollution. Each of the dumpsite was divided into north, south, east and west. Four soil samples were collected at a depth of 0-15 cm from each part and pooled to form a composite sample. Soil samples from ...

  13. Effect of EDTA on divalent metal adsorption onto grape stalk and exhausted coffee wastes.

    Science.gov (United States)

    Escudero, Carlos; Gabaldón, Carmen; Marzal, Paula; Villaescusa, Isabel

    2008-04-01

    In the present work, two industrial vegetable wastes, grape stalk, coming from a wine producer, and exhausted coffee, coming from a soluble coffee manufacturer, have been investigated for the removal of Cu(II) and Ni(II) from aqueous solutions in presence and in absence of the strongly complexing agent EDTA. Effects of pH and metal-EDTA molar ratio, kinetics as a function of sorbent concentration, and sorption equilibrium for both metals onto both sorbents were evaluated in batch experiments. Metal uptake was dependent of pH, reaching a maximum from pH around 5.5. EDTA was found to dramatically reduce metal adsorption, reaching total uptake inhibition for both metals onto both sorbents at equimolar metal:ligand concentrations. Kinetic results were successfully modelled by means of the pseudo second order model. Langmuir and Freundlich models were used to describe the sorption equilibrium data. Grape stalk showed the best performance for Cu(II) and Ni(II) removal in presence and in absence of EDTA, despite exhausted coffee appears as less sensitive to the presence of complexing agent. The performance of Cu(II) and Ni(II) sorption onto grape stalk in a continuous flow process was evaluated. In solutions containing EDTA, an initial metal concentration in the outlet flow corresponding to the complexed metal fraction was observed from the beginning of the process. A high metal recovery yield (>97%) was achieved by feeding the metal-loaded column with 0.05 M HCl.

  14. Potential utilisation of sewage sludge and paper mill waste for biosorption of metals from polluted waterways.

    Science.gov (United States)

    Lister, S K; Line, M A

    2001-08-01

    The adsorption of cadmium, copper(II), lead and zinc ions from aqueous solution by sewage sludge, paper mill waste (PMW) and composted PMW was investigated along with the influence of pre-treatment on composted PMW. Langmuir adsorption isotherms were fitted where appropriate. Sewage sludge was the most effective biosorbent of the waste products for all metal ions examined, adsorbing, for example, up to 39.3 mg/g of Pb at an initial concentration of 77.8 mg/l. PMW was a less effective biosorbent than sewage sludge. However, it was found that composting the PMW resulted in an increase in metal uptake capacity and both sewage sludge and composted PMW have potential for low-cost remediation of high leachate wastewaters. The desorption of metal ions from PMW compost was most effective using 0.1 N H2SO4 and 1 mM nitrilotriacetic acid (NTA).

  15. Exposure assessment of heavy metals in an e-waste processing area in northern Vietnam.

    Science.gov (United States)

    Oguri, Tomoko; Suzuki, Go; Matsukami, Hidenori; Uchida, Natsuyo; Tue, Nguyen Minh; Tuyen, Le Huu; Viet, Pham Hung; Takahashi, Shin; Tanabe, Shinsuke; Takigami, Hidetaka

    2018-04-15

    In developing countries, inappropriate recycling of e-waste has resulted in the environmental release of toxicants, including heavy metals, that may have deleterious health effects. In this study, we estimated daily metal intakes in five households in a Vietnamese village located in an e-waste processing area and assessed the health risk posed by exposure to the metals. Garden soil, floor dust, 24-h duplicate diet, and ambient air samples were collected from five households in northern Vietnam in January 2014. All samples were acid-digested, and contents of Cd, Cu, Mn, Pb, Sb, and Zn were measured by using ICP mass spectrometry and ICP atomic emission spectroscopy. In addition, the soil, dust, and diet samples were subjected to an bioaccessibility extraction test to determine bioaccessible metal concentrations. Hazard quotients were estimated from bioaccessible metal concentrations, provisional tolerable weekly intakes, and reference doses. Garden soil and floor dust were estimated to be mainly contributors to daily Pb intake, as indicated by calculations using bioaccessible metal concentrations and the U.S. Environmental Protection Agency soil plus dust ingestion rate. Diet was suggested to contribute significantly to daily Cd, Cu, Mn, Sb, and Zn intake. Estimated metal exposures via inhalation were negligible, as indicated by calculations using International Atomic Energy Agency reference inhalation rates. The maximum hazard quotients were calculated as 0.2 (Cd), 0.09 (Cu), 0.3 (Mn), 0.6 (Pb), 0.2 (Sb), and 0.5 (Zn), on the basis of bioaccessible metal concentrations. The contributions of Cd, Cu, Mn, Sb, and Zn except Pb to potential noncancer risk for adult residents of the five households in the e-waste processing area may be low. Copyright © 2017 Elsevier B.V. All rights reserved.

  16. Monitoring Metal Pollution Levels in Mine Wastes around a Coal Mine Site Using GIS

    Science.gov (United States)

    Sanliyuksel Yucel, D.; Yucel, M. A.; Ileri, B.

    2017-11-01

    In this case study, metal pollution levels in mine wastes at a coal mine site in Etili coal mine (Can coal basin, NW Turkey) are evaluated using geographical information system (GIS) tools. Etili coal mine was operated since the 1980s as an open pit. Acid mine drainage is the main environmental problem around the coal mine. The main environmental contamination source is mine wastes stored around the mine site. Mine wastes were dumped over an extensive area along the riverbeds, and are now abandoned. Mine waste samples were homogenously taken at 10 locations within the sampling area of 102.33 ha. The paste pH and electrical conductivity values of mine wastes ranged from 2.87 to 4.17 and 432 to 2430 μS/cm, respectively. Maximum Al, Fe, Mn, Pb, Zn and Ni concentrations of wastes were measured as 109300, 70600, 309.86, 115.2, 38 and 5.3 mg/kg, respectively. The Al, Fe and Pb concentrations of mine wastes are higher than world surface rock average values. The geochemical analysis results from the study area were presented in the form of maps. The GIS based environmental database will serve as a reference study for our future work.

  17. One-pot synthesis of carbon supported calcined-Mg/Al layered double hydroxides for antibiotic removal by slow pyrolysis of biomass waste

    Science.gov (United States)

    Tan, Xiaofei; Liu, Shaobo; Liu, Yunguo; Gu, Yanling; Zeng, Guangming; Cai, Xiaoxi; Yan, Zhili; Yang, Chunping; Hu, Xinjiang; Chen, Bo

    2016-12-01

    A biochar supported calcined-Mg/Al layered double hydroxides composite (CLDHs/BC) was synthesized by a one-pot slow pyrolysis of LDHs preloaded bagasse biomass. Multiple characterizations of the product illustrated that the calcined-Mg/Al layered double hydroxides (CLDHs) were successfully coated onto the biochar in slow pyrolysis of pre-treated biomass. The as-synthesized CLDHs/BC could efficiently remove antibiotic tetracycline from aqueous solutions. The coating of CLDHs significantly increased the adsorption ability of biochar, and CLDHs/BC exhibited more than 2 times higher adsorption capacity than that of the pristine biochar (BC) in the tested pH range. The maximum adsorption capacity of CLDHs/BC for tetracycline was 1118.12 mg/g at 318 K. The experimental results suggested that the interaction with LDHs on biochar played a dominant role in tetracycline adsorption, accompanied with π-π interaction and hydrogen bond. This study provides a feasible and simple approach for the preparation of high-performance material for antibiotics contaminated wastewater treatment in a cost-effective way.

  18. Rare and Rare-Earth Metals in Coal Processing Waste

    Science.gov (United States)

    Cherkasova, Tatiana; Cherkasova, Elizaveta; Tikhomirova, Anastasia; Bobrovni-kova, Alyona; Goryunova, Irina

    2017-11-01

    An urgent issue for power plants operating on solid fuels (coal) is the issue of utilization or use of accumulated production waste - ash and slag materials - in the related production. Ash-slag materials are classified as "waste", usually grade 5; tens of millions of tons of them being pro-duced annually in the Kemerovo region, which threatens the ecology of the region. At the same time, ash and slag is a very promising raw material. The use of this material as a base for the final product allows us to signifi-cantly expand the possibilities of using coal. The most widespread is the system of ash and slag involving in construction or as a replacement for sand in road construction, or as an additive to building mixtures. However, there are both industrially valuable and environmentally dangerous ele-ments in ash-slag materials. Ash-slag materials can be considered as inde-pendent ore deposits located on the surface and requiring the costs of their extraction.

  19. Evaluation of extractant-coated ferromagnetic microparticles for the recovery of hazardous metals from waste solution.

    Energy Technology Data Exchange (ETDEWEB)

    Kaminski, M. D.

    1998-05-08

    A magnetically assisted chemical separation (MACS) process was developed earlier at Argonne National Laboratory (ANL). This compact process was designed for the separation of transuranics (TRU) and radionuclides from the liquid waste streams that exist at many DOE sites, with an overall reduction in waste volume requiring disposal. The MACS process combines the selectivity afforded by solvent extractant/ion exchange materials with magnetic separation to provide an efficient chemical separation. Recently, the MACS process has been evaluated with acidic organophosphorus extractants for hazardous metal recovery from waste solutions. Moreover, process scale-up design issues have been addressed with respect to particle filtration and recovery. Two acidic organophosphorus compounds have been investigated for hazardous metal recovery, bis(2,4,4-trimethylpentyl) phosphinic acid (Cyanex{reg_sign} 272) and bis(2,4,4-trimethylpentyl) dithiophosphinic acid (Cyanex{reg_sign} 301). Coated onto magnetic microparticles, these extractants demonstrated superior recovery of hazardous metals from solution, relative to what was expected on the basis of results from solvent extraction experiments. The results illustrate the diverse applications of MACS technology for dilute waste streams. Preliminary process scale-up experiments with a high-gradient magnetic separator at Oak Ridge National Laboratory have revealed that very low microparticle loss rates are possible.

  20. Waste Derived Sorbents and Their Potential Roles in Heavy Metal Remediation Applications

    Directory of Open Access Journals (Sweden)

    Chiang Y. W.

    2013-04-01

    Full Text Available Inorganic waste materials that have the suitable inherent characteristics could be used as precursors for the synthesis of micro- and mesoporous materials, which present great potential to be re-utilized as sorbent materials for heavy metal remediation. Three inorganic waste materials were studied in the present work: water treatment residuals (WTRs from an integrated drinking water/wastewater treatment plant, and fly ash and bottom ash samples from a municipal solid waste incinerator (MSWI. These wastes were converted into three sorbent materials: ferrihydrite-like materials derived from drying of WTRs, hydroxyapatite-like material derived from ultrasound assisted synthesis of MSWI fly ash with phosphoric acid solution, and a zeolitic material derived from alkaline hydrothermal conversion of MSWI bottom ash. The performance of these materials, as well as their equivalent commercially available counterparts, was assessed for the adsorption of multiple heavy metals (As, Cd, Co, Ni, Pb, Zn from synthetic solutions, contaminated sediments and surface waters; and satisfactory results were obtained. In addition, it was observed that the combination of sorbents into sorbent mixtures enhanced the performance levels and, where applicable, stabilized inherently mobile contaminants from the waste derived sorbents.

  1. Conversion coatings prepared or treated with calcium hydroxide solutions

    Science.gov (United States)

    Minevski, Zoran (Inventor); Clarke, Eric (Inventor); Maxey, Jason (Inventor); Nelson, Carl (Inventor); Eylem, Cahit (Inventor)

    2002-01-01

    A conversion coating process that forms a stable and corrosion-resistant oxide layer on metal or metal oxide substrates or layers. Particularly, the conversion coating process involves contacting the metal or metal oxide substrate or layer with the aqueous calcium hydroxide solutions in order to convert the surface of the substrate to a stable metal oxide layer or coating. According to the present invention, the calcium hydroxide solution is prepared by removing carbon dioxide from water or an aqueous solution before introducing the calcium hydroxide. In this manner, formation of calcium carbonate particles is avoided and the porosity of the conversion coating produced by the calcium hydroxide solution is reduced to below about 1%.

  2. Bioleaching of metal concentrates of waste printed circuit boards by mixed culture of acidophilic bacteria.

    Science.gov (United States)

    Zhu, Nengwu; Xiang, Yun; Zhang, Ting; Wu, Pingxiao; Dang, Zhi; Li, Ping; Wu, Jinhua

    2011-08-30

    Metal concentrates of printed circuit boards (PCBs) are the residue valuable metals from which non-metallic components are removed. The non-metallic components show bacterial toxicity in bioleaching process and can be recycled as well. In this study, the effects of initial pH, initial Fe(II) concentration, metal concentrate dosage, particle size, and inoculation quantity on the bioleaching were investigated so as to determine the optimum conditions and evaluate the feasibility of bioleaching of metal concentrates of PCBs by mixed culture of acidophilic bacteria (MCAB). The results showed that the initial pH and Fe(II) concentration played an important role in copper extraction and precipitate formation. Under the optimized conditions of initial pH 2.00, 12g/L initial Fe(II), 12g/L metal concentrate dosage, 10% inoculation quantity, and 60-80 mesh particle size, 96.8% the copper leaching efficiency was achieved in 45h, and aluminum and zinc 88.2% and 91.6% in 98h, respectively. All findings demonstrated that metals could be efficiently leached from metal concentrates of waste PCBs by using the MCAB, and the leaching period was shorten from about 8 days to 45h. Copyright © 2011 Elsevier B.V. All rights reserved.

  3. Assessing the leaching of hazardous metals from pharmaceutical wastes and their ashes.

    Science.gov (United States)

    Gerassimidou, Spyridoula; Komilis, Dimitrios

    2015-02-01

    The purpose of this research was the determination of the leaching potential of eight hazardous metals from expired pharmaceutical wastes and their ashes obtained after simulated incineration. A standardized leaching test (EN 14429) was used to assess leaching over a range of pH and comparison with the limits included in Decision 2003/33/EC was done at liquid/solid ratio 10. The goal was to assess the environmental impacts of pharmaceutical wastes after different disposal techniques (direct landfilling, incineration). A 3-year old composite sample of expired pharmaceutical wastes (drugs) was obtained and was separated into solid and liquid drugs. The packaging from each type of drug was also removed and tested separately, whilst the solid drugs and their packaging were incinerated at 900°C. Leaching tests on all solid substrates (solid drugs, packaging, ashed drugs, ashed packaging) were performed over a wide range of pH. The experiments showed that ashed drugs leached the highest amounts of all metals, except iron, and should be disposed of to a hazardous waste landfill, since Cd, Ni, and Pb exceeded the corresponding limits. Raw expired drugs, raw and ashed packaging did not exceed the pertinent limit values and could be, thus, disposed of directly to a non-hazardous waste landfill. In all experiments, the highest leaching potential (>90% of the total metal content) was measured at acidic pHs (<4). The leachable concentration of all metals increased as pH decreased, whilst Zn observed a small re-dissolution in the alkaline range. © The Author(s) 2015.

  4. Influence of municipal solid waste compost application on heavy metal content in soil.

    Science.gov (United States)

    Yuksel, Orhan

    2015-06-01

    Municipal solid waste composts (MSWC) are widely used over agricultural lands as organic soil amendment and fertilizer. However, MSWC use may result in various adverse impacts over agricultural lands. Especially, heavy metal contents of MSWC should always be taken into consideration while using in agricultural practices. The present study was conducted to find out heavy metal contents of municipal solid waste compost (MSWC) and to investigate their effects on soils. Experiments were carried out in three replications as field experiments for 2 years. Dry-based MSWC was applied to each plot at the ratios of 0, 40, 80, 120, 160, 200 t ha(-1). Results revealed that heavy metal content of MSWC was within the allowable legal limits. Compost treatments significantly increased Cu, Zn, Ni, Cr, Cd, and Pb content of soils (p compost doses. Although compost treatments significantly increased soil heavy metal contents, the final contents were still within the allowable legal limits. Results showed that MSWC doses over 10 t ha(-1) may create a heavy metal risk in long term for soils with pH ≥ 7. Therefore, in MSWC use over agricultural lands, heavy metal contents should always be taken into consideration and excessive uses should be avoided.

  5. Removal of heavy metals from aqueous phases using chemically modified waste Lyocell fiber

    Energy Technology Data Exchange (ETDEWEB)

    Bediako, John Kwame; Wei, Wei; Kim, Sok; Yun, Yeoung-Sang, E-mail: ysyun@jbnu.ac.kr

    2015-12-15

    Highlights: • Waste Lyocell fiber was chemically modified into cellulose xanthate. • The sorbent showed high affinity for Pb(II), Cd(II) and Cu(II) ions. • The sorbent also showed strong Cu(II) selectivity in Pb(II)–Cd(II)–Cu(II) ternary metal solutions. - Abstract: In this study, an outstanding performance of chemically modified waste Lyocell for heavy metals treatment is reported. The sorbent, which was prepared by a simple and concise method, was able to bind heavy metals such as Pb(II), Cu(II) and Cd(II), with very high efficiencies. The binding mechanisms were studied through adsorption and standard characterization tests such as scanning electron microscopy, energy-dispersive spectroscopy, Fourier transform infrared spectroscopy, and X-ray diffraction analyses. Adsorption kinetics was very fast and attained equilibrium within 5 min in all metals studied. The maximum single metal uptakes were 531.29 ± 0.28 mg/g, 505.64 ± 0.21 mg/g, and 123.08 ± 0.26 mg/g for Pb(II), Cd(II) and Cu(II), respectively. In ternary metal systems, Cu(II) selectivity was observed and the underlying factors were discussed. The sorbent by its nature, could be very effective in treating large volumes of wastewater with the contact of very little amount.

  6. RECOVERY OF GOLD (Au) AND SILVER (Ag) METALS IN THE ELECTRONIC WASTE THROUGH MULTILEVEL PRECIPITATION PROCESS

    OpenAIRE

    Siti Marwati; Regina Tutik Padmaningrum; Sunarto Sunarto

    2016-01-01

    This research aims to determine the percent recovery of gold (Au) and silver (Ag) in the electronic waste such as CD-RW and determine the purity of gold and silver metals in the electronic waste such as CD-RW that through multilevel precipitation process. The first step was the optimization of the concentration of thiourea and time dissolution of gold and silver in the sample. The concentration of thiourea and the time dissolution optimum obtained from conentration of gold and silver maximum....

  7. Heavy metal migration during electroremediation of fly ash from different wastes--modelling.

    Science.gov (United States)

    Lima, A T; Rodrigues, P C; Mexia, J T

    2010-03-15

    Fly ash is an airborne material which is considered hazardous waste due to its enrichment on heavy metals. Depending on the waste from which they are originated, fly ash may be further valorised, e.g. as soil amendment or concrete and ceramics adjuvant, or landfilled, when defined as hazardous material. In any case, heavy metal content has to be decreased either for fly ash valorisation or for complying with landfill criteria. The electrodialytic (EDR) process is a remediation technique based on the principle of electrokinetics and dialysis, having the aim to remove heavy metals from contaminated solid media. EDR was here applied to fly ashes from the combustion of straw (ST), from the incineration of municipal solid waste (DK and PT) and from the co-combustion of wood (CW). A statistical study, using F tests, Bonferroni multiple comparison method and a categorical regression, was carried out to determine which variables ("Ash type", "Duration", "Initial pH", "Final pH", "Acidification" and "Dissolution") were the most significant for EDR efficiency. After establishing these, the selected variables were then used to characterize some kinetic parameters, from metals migration during EDR, using a biregressional design. Cd, Cr, Cu, Ca and Zn migration velocity and acceleration to the electrodes (anode and cathode) were then considered. Cd and Cu migration to the cathode were found to be significantly influenced by "Ash type", "Duration", "Final pH" and "Dissolution". (c) 2009 Elsevier B.V. All rights reserved.

  8. Biorefining of platinum group metals from model waste solutions into catalytically active bimetallic nanoparticles.

    Science.gov (United States)

    Murray, Angela J; Zhu, Ju; Wood, Joe; Macaskie, Lynne E

    2018-03-01

    Bacteria can fabricate platinum group metal (PGM) catalysts cheaply, a key consideration of industrial processes and waste decontaminations. Biorecovery of PGMs from wastes is promising but PGM leachates made from metallic scraps are acidic. A two-step biosynthesis 'pre-seeds' metallic deposits onto bacterial cells benignly; chemical reduction of subsequent metal from acidic solution via the seeds makes bioscaffolded nanoparticles (NPs). Cells of Escherichia coli were seeded using Pd(II) or Pt(IV) and exposed to a mixed Pd(II)/Pt(IV) model solution under H 2 to make bimetallic catalyst. Its catalytic activity was assessed in the reduction of Cr(VI), with 2 wt% or 5 wt% preloading of Pd giving the best catalytic activity, while 1 wt% seeds gave a poorer catalyst. Use of Pt seeds gave less effective catalyst in the final bimetallic catalyst, attributed to fewer and larger initial seeds as shown by electron microscopy, which also showed a different pattern of Pd and Pt deposition. Bimetallic catalyst (using cells preloaded with 2 wt% Pd) was used in the hydrogenation of soybean oil which was enhanced by ~fourfold using the bimetallic catalyst made from a model waste solution as compared to 2 wt% Pd preloaded cells alone, with a similar selectivity to cis C18:1 product as found using a Pd-Al 2 O 3 commercial catalyst. © 2018 The Authors. Microbial Biotechnology published by John Wiley & Sons Ltd and Society for Applied Microbiology.

  9. Heavy metal contamination from electronic waste recycling at Guiyu, Southeastern China.

    Science.gov (United States)

    Guo, Yan; Huang, Changjiang; Zhang, Hong; Dong, Qiaoxiang

    2009-01-01

    This study evaluated the effect of electronic waste (e-waste) recycling activities at a regional center, Guiyu, Guangdong, China on heavy metal pollution in the surrounding waterway system. Surface water and sediment collected from the Lianjiang River and its tributaries were analyzed for concentrations of Cu, Pb, Ni, Cd, Hg, and As. Spatially, heavy metals in water and sediment samples decreased downstream of Lianjiang River from Guiyu to the estuary at Haimen Bay. Temporally, heavy metal concentrations in the surface water were high in the rainy season and low in the dry season. In particular, concentrations of Cu from surface water in the Guiyu area were 2.4 to 131 times the reference background concentration, followed in descending order by Ni, Cd, Pb, Hg, and As. However, when compared with China's Environmental Quality Standard, Cd was considered the most harmful element, followed by Hg, Pb, and Cu. Concentrations of Cu in sediment samples in the Guiyu area were 3.2 to 429 times the reference background concentration, followed by Ni, Hg, Pb, Cd, and As. Our findings suggested that high concentrations of heavy metal observed in Guiyu, Lianjiang River and the Haimen Bay could be attributed to the direct effects of e-waste recycling in Guiyu.

  10. Heavy metals extraction from municipal solid waste incineration fly ash using adapted metal tolerant Aspergillus niger.

    Science.gov (United States)

    Yang, Jie; Wang, Qunhui; Wang, Qi; Wu, Tingji

    2009-01-01

    This study focused on the adaptation of Aspergillus niger tolerating high concentration of heavy metals for bioleaching of fly ash. The Plackett-Burman design indicated that Al and Fe inhibited the growth of A. niger (AS 3.879 and AS 3.40) significantly. The single metal (Al and Fe) and multi-metals adapted AS 3.879 strain tolerated up to 3500 mg/L Al, 700 mg/L Fe, and 3208.1mg/L multi-metals, respectively. The order of metal extraction yield in two-step bioleaching of 60 and 70 g/L fly ash using Al adapted, multi-metals adapted and un-adapted AS 3.879 strains was as follows: multi-metals adapted>Al adapted>un-adapted. The multi-metals adapted strain grew with up to 70 g/L fly ash and secreted 256 mmol/L organic acids after 288 h, where 87.4% Cd, 64.8% Mn, 49.4% Zn and 45.9% Pb were dissolved. The extracted metals in TCLP test of the bioleached fly ash by multi-metals adapted strain were under the regulated levels in China.

  11. Disintegration and size reduction of slags and metals after melt refining of contaminated metallic wastes

    Energy Technology Data Exchange (ETDEWEB)

    Heshmatpour, B.; Copeland, G.L.; Heestand, R.L.

    1981-04-01

    Melting under an oxidizing slag is an attractive method of decontaminating and reducing the volume of radioactively contaminated metal scrap. The contaminants are concentrated in a relatively small volume of slag, which leaves the metal essentially clean. A potential method of permanently disposing of the resulting slags (and metals if necessary) is emplacing them into deep shale by grout hydrofracture. Suspension in grout mixtures requires that the slag and metal be granular. The feasibility of size-reducing slags and disintegrating metals and subsequently incorporating both into grout mixtures was demonstrated. Various types of slags were crushed with a small jaw crusher into particles smaller than 3 mm. Several metals were also melted and water-blasted into coarse metal powder or shot ranging in size from 0.05 to 3 mm. A simple low-pressure water atomizer having a multiple nozzle with a converging-line jet stream was developed and used for this purpose. No significant slag dust and steam were generated during slag crushing and liquid-metal water-blasting tests, indicating that contamination can be well contained within the system. The crushed slags and the coarse metal powders were suspendable in group fluids, which indicates probable disposability by shale hydrofracture. The granulation of slags and metals facilitates their containment, transport, and storage.

  12. Leaching of heavy metals from solidified waste using Portland cement and zeolite as a binder.

    Science.gov (United States)

    Napia, Chuwit; Sinsiri, Theerawat; Jaturapitakkul, Chai; Chindaprasirt, Prinya

    2012-07-01

    This study investigated the properties of solidified waste using ordinary Portland cement (OPC) containing synthesized zeolite (SZ) and natural zeolite (NZ) as a binder. Natural and synthesized zeolites were used to partially replace the OPC at rates of 0%, 20%, and 40% by weight of the binder. Plating sludge was used as contaminated waste to replace the binder at rates of 40%, 50% and 60% by weight. A water to binder (w/b) ratio of 0.40 was used for all of the mixtures. The setting time and compressive strength of the solidified waste were investigated, while the leachability of the heavy metals was determined by TCLP. Additionally, XRD, XRF, and SEM were performed to investigate the fracture surface, while the pore size distribution was analyzed with MIP. The results indicated that the setting time of the binders marginally increased as the amount of SZ and NZ increased in the mix. The compressive strengths of the pastes containing 20 and 40wt.% of NZ were higher than those containing SZ. The compressive strengths at 28 days of the SZ solidified waste mixes were 1.2-31.1MPa and those of NZ solidified waste mixes were 26.0-62.4MPa as compared to 72.9MPa of the control mix at the same age. The quality of the solidified waste containing zeolites was better than that with OPC alone in terms of the effectiveness in reducing the leachability. The concentrations of heavy metals in the leachates were within the limits specified by the US EPA. SEM and MIP revealed that the replacement of Portland cement by zeolites increased the total porosity but decreased the average pore size and resulted in the better containment of heavy ions from the solidified waste. Copyright © 2012 Elsevier Ltd. All rights reserved.

  13. An environmentally friendly ball milling process for recovery of valuable metals from e-waste scraps.

    Science.gov (United States)

    Zhang, Zhi-Yuan; Zhang, Fu-Shen; Yao, TianQi

    2017-10-01

    The present study reports a mechanochemical (MC) process for effective recovery of copper (Cu) and precious metals (i.e. Pd and Ag) from e-waste scraps. Results indicated that the mixture of K 2 S 2 O 8 and NaCl (abbreviated as K 2 S 2 O 8 /NaCl hereafter) was the most effective co-milling reagents in terms of high recovery rate. After co-milling with K 2 S 2 O 8 /NaCl, soluble metallic compounds were produced and consequently benefit the subsequent leaching process. 99.9% of Cu and 95.5% of Pd in the e-waste particles could be recovered in 0.5mol/L diluted HCl in 15min. Ag was concentrated in the leaching residue as AgCl and then recovered in 1mol/L NH 3 solution. XRD and XPS analysis indicated that elemental metals in the raw materials were transformed into their corresponding oxidation state during ball milling process at low temperature, implying that solid-solid phase reactions is the reaction mechanism. Based on the results and thermodynamic parameters of the probable reactions, possible reaction pathways during ball milling were proposed. Suggestion on category of e-waste for ball milling process was put forward according to the experiment results. The designed metal recovery process of this study has the advantages of highly recovery rate and quick leaching speed. Thus, this study offers a promising and environmentally friendly method for recovering valuable metals from e-waste. Copyright © 2017 Elsevier Ltd. All rights reserved.

  14. Heavy Metals Removal from Sewage Sludge and Municipal Solid Waste (MSW by Co-Composting Process

    Directory of Open Access Journals (Sweden)

    Vahid Babaee Darzi

    2017-07-01

    Full Text Available Background & Aims of the Study: One of the most important pollutants in drinking water, air and soils is heavy metals. It is very harmful for humans and other live organisms. The purpose of this study was the usage of a co-composting process for removal of heavy metals from municipal solid waste and sewage sludge. Materials and Methods: This experimental study was a conducted sewage sludge and municipal solid waste. For collection of samples from urban solid waste composting and wastewater treatment plant, a 200 mL polyethylene bottles was used, samples after acidification were stored in a dark place at 4°C temperature until the metals analysis the heavy metals values remaining in the samples was measured by graphite furnace absorption spectrometer method (Varian, SpectrAA 240, Australia. In this study, we used SPSS version 16 for data processing; and they were also analyzed by descriptive statistics. Results: Result of this study showed that values of C/N in the first, second and third stage compost were 31.7, 27.3 and 41.8, respectively. Based on the result of this study the value of removal of Cd with 9.8 mg kg-1 in first stage and Cr, Cu and Zn with 89, 21 and 87.6 mg kg-1 in third stage were highest treatment. Conclusion: Our results show that co-composting process between many treatment processes having to be cost effective for heavy metal removal from solid waste and wastewater treatment.

  15. [Effects of stabilization treatment on migration and transformation of heavy metals in mineral waste residues].

    Science.gov (United States)

    Zhao, Shu-Hua; Chen, Zhi-Liang; Zhang, Tai-Ping; Pan, Wei-Bin; Peng, Xiao-Chun; Che, Rong; Ou, Ying-Juan; Lei, Guo-Jian; Zhou, Ding

    2014-04-01

    Different forms of heavy metals in soil will produce different environmental effects, and will directly influence the toxicity, migration and bioavailability of heavy metals. This study used lime, fly ash, dried sludge, peanut shells as stabilizers in the treatment of heavy metals in mineral waste residues. Morphological analyses of heavy metal, leaching experiments, potted plant experiments were carried out to analyze the migration and transformation of heavy metals. The results showed that after adding stabilizers, the pH of the acidic mineral waste residues increased to more than neutral, and the organic matter content increased significantly. The main existing forms of As, Pb, and Zn in the mineral waste residues were the residual. The contents of exchangeable and organic matter-bound As decreased by 65.6% and 87.7% respectively after adding fly ash, dried sludge and peanut shells. Adding lime, fly ash and peanut shells promoted the transformation of As from the Fe-Mn oxide-bound to the carbonate-bound, and adding lime and fly ash promoted the transformation of Pb and Zn from the exchangeable, Fe-Mn oxide-bound, organic matter-bound to the residual. After the early stage of the stabilization treatment, the contents of As, Pb and Zn in the leachate had varying degrees of decline, and adding peanut shells could reduce the contents of As, Pb and Zn in the leachate further. Among them, the content of As decreased most significantly after treatment with fly ash, dried sludge and peanut shells, with a decline of 57.4%. After treatment with lime, fly ash and peanut shells, the content of Zn decreased most significantly, by 24.9%. The addition of stabilizers was advantageous to the germination and growth of plants. The combination of fly ash, dried sludge and peanut shell produced the best effect, and the Vetiveria zizanioides germination rate reached 76% in the treated wasted mineral residues.

  16. Closing the Phosphorus Loop by Recovering Phosphorus From Waste Streams With Layered Double Hydroxide Nanocomposites and Converting the Product into an Efficient Fertilizer

    Science.gov (United States)

    Yan, H.; Shih, K.

    2015-12-01

    Phosphorus (P) recovery has been frequently discussed in recent decades due to the uncertain availability and uneven distribution of global phosphate rock reserves. Sorption technology is increasingly considered as a reliable, efficient and environmentally friendly P removal method from aqueous solution. In this study, a series of Mg-Al-based layered double hydroxide nanocomposites and their corresponding calcined products were fabricated and applied as phosphate adsorbents. The prepared samples were with average size at ~50 nm and self-assembled into larger particles in irregular shapes. The results of batch adsorption experiments demonstrated that calcination significantly enhanced the adsorption ability of LDHs for phosphorus, and the maximum adsorption capacity of calcined Mg-Al-LDH was as high as 100.7 mg-P/g. Furthermore, incorporation of Zr4+ and La3+ into LDH materials increases the sorption selectivity as well as sorption amount of phosphorus in LDHs, which was confirmed by experiments operated in synthetic human urine. For the first time ammonia (NH4OH) and potassium hydroxide (KOH) solutions were employed to desorb the P-loaded LDH. Identification of solids derived from two eluting solutions showed that struvite (MgNH4PO4•6H2O, MAP) was precipitated in ammonia solution while most phosphate was desorbed into liquid phase in KOH system without crystallization of potassium struvite (MgKPO4•6H2O) due to its higher solubility. Quantitative X-ray diffraction technique was used to determine struvite contents in obtained solids and the results revealed that ~ 30% of adsorbed P was transferred into struvite form in the sample extracted by 0.5M NH4OH. Leaching tests suggested that the phosphorus releasing kinetics of ammonia treated LDH was comparable to that of pure struvite product, indicating that postsorption Mg-Al-LDH desorbed with ammonia could serve as a slow-releasing fertilizer in agriculture (see Figure 1).

  17. Spatial distribution of heavy metal contamination in soils near a primitive e-waste recycling site.

    Science.gov (United States)

    Quan, Sheng-Xiang; Yan, Bo; Yang, Fan; Li, Ning; Xiao, Xian-Ming; Fu, Jia-Mo

    2015-01-01

    The total concentrations of 12 heavy metals in surface soils (SS, 0-20 cm), middle soils (MS, 30-50 cm) and deep soils (DS, 60-80 cm) from an acid-leaching area, a deserted paddy field and a deserted area of Guiyu were measured. The results showed that the acid-leaching area was heavily contaminated with heavy metals, especially in SS. The mean concentrations of Ni, Cu, Zn, Cd, Sn, Sb and Pb in SS from the acid-leaching area were 278.4, 684.1, 572.8, 1.36, 3,472, 1,706 and 222.8 mg/kg, respectively. Heavy metal pollution in the deserted paddy field was mainly concentrated in SS and MS. The average values of Sb in SS and MS from the deserted paddy field were 16.3 and 20.2 mg/kg, respectively. However, heavy metal contamination of the deserted area was principally found in the DS. Extremely high concentrations of heavy metals were also observed at some special research sites, further confirming that the level of heavy metal pollution was very serious. The geoaccumulation index (Igeo) values revealed that the acid-leaching area was severely polluted with heavy metals in the order of Sb > Sn > Cu > Cd > Ni > Zn > Pb, while deserted paddy field was contaminated predominately by metals in the order of Sb > Sn > Cu. It was obvious that the concentrations of some uncommon contaminants, such as Sb and Sn, were higher than principal contaminants, such as Ni, Cu, Zn and Pb, suggesting that particular attention should be directed to Sn and Sb contamination in the future research of heavy metals in soils from e-waste-processing areas. Correlation analysis suggested that Li and Be in soils from the acid-leaching area and its surrounding environment might have originated from other industrial activities and from batteries, whereas Ni, Cu, Zn, Cd, Pb, Sn and Sb contamination was most likely caused by uncontrolled electronic waste (e-waste) processing. These results indicate the significant need for optimisation of e-waste-dismantling technologies and remediation of polluted soil

  18. Precipitation of heavy metals in waste waters; Precipitacion de metales pesados en las aguas residuales

    Energy Technology Data Exchange (ETDEWEB)

    Stutzel, K.; Peldszus, R.

    1997-06-01

    Heavy metals content in effluents is regulated due to their toxicity. To minimized them different precipitating agents are used. A comparison between some precipitating agents (the most common is H{sub 2}S) wit trimercapto-s-triazine (TMT 15) is shown. Solubility products of TMT 15 with divalent metals are very low: the precipitation with TMT 15 gives a heavy metal concentration in effluents below regulated levels. (Author)

  19. Nickel-cobalt hydroxide nanosheets: Synthesis, morphology and electrochemical properties.

    Science.gov (United States)

    Schneiderová, Barbora; Demel, Jan; Zhigunov, Alexander; Bohuslav, Jan; Tarábková, Hana; Janda, Pavel; Lang, Kamil

    2017-08-01

    This paper reports the synthesis, characterization, and electrochemical performance of nickel-cobalt hydroxide nanosheets. The hydroxide nanosheets of approximately 0.7nm thickness were prepared by delamination of layered nickel-cobalt hydroxide lactate in water and formed transparent colloids that were stable for months. The nanosheets were deposited on highly oriented pyrolytic graphite by spin coating, and their electrochemical behavior was investigated by cyclic voltammetry in potassium hydroxide electrolyte. Our method of electrode preparation allows for studying the electrochemistry of nanosheets where the majority of the active centers can participate in the charge transfer reaction. The observed electrochemical response was ascribed to mutual compensation of the cobalt and nickel response via electron sharing between these metals in the hydroxide nanosheets, a process that differentiates the behavior of nickel-cobalt hydroxide nanosheets from single nickel hydroxide or cobalt hydroxide nanosheets or their physical mixture. The presence of cobalt in the nickel-cobalt hydroxide nanosheets apparently decreases the time of electrochemical activation of the nanosheet layer, which for the nickel hydroxide nanosheets alone requires more potential sweeps. Copyright © 2017 Elsevier Inc. All rights reserved.

  20. Application of vacuum metallurgy to separate pure metal from mixed metallic particles of crushed waste printed circuit board scraps.

    Science.gov (United States)

    Zhan, Lu; Xu, Zhenming

    2008-10-15

    The principle of separating pure metal from mixed metallic particles (MMPs) byvacuum metallurgy is that the vapor pressures of various metals at the same temperature are different As a result, the metal with high vapor pressure and low boiling point can be separated from the mixed metals through distillation or sublimation, and then it can be recycled through condensation under a certain condition. The vacuum metallurgy separation (VMS) of MMPs of crushed waste printed circuit boards (WPCBs) has been studied in this paper. Theoretical analyses show that the MMPs (copper, zinc, bismuth, lead, and indium, for example) can be separated by vacuum metallurgy. The copper particles (0.15-0.20 mm) and zinc particles (<0.30 mm) were chosen to simulate the MMPs of crushed WPCBs. Experimental results show that the separated efficiency of zinc in the copper-rich particles achieves 96.19 wt % when the vacuum pressure is 0.01-0.10 Pa, the heating temperature is 1123 K, and the heating time is 105 min. Under this operation condition, the separated efficiency of zinc in the copper-rich particles from crushed WPCBs achieves 97.00 wt % and the copper purity increases from 90.68 to 99.84 wt %.

  1. Recovery of Precious and Base Metals from Waste Printed Circuit Boards Using a Sequential Leaching Procedure

    Science.gov (United States)

    Batnasan, Altansukh; Haga, Kazutoshi; Shibayama, Atsushi

    2018-02-01

    This paper considers the issue of recycling of waste printed circuit boards (WPCBs) containing precious and base metals in appreciable amounts. High-pressure oxidative leaching (HPOL) with dilute sulfuric acid resulted in removal of a significant amount of base metals from a WPCB ash sample obtained by incineration at 800°C. The parameters investigated in the precious metal leaching from WPCB residue after HPOL included the sulfuric acid concentration, thiourea concentration, oxidant concentration, leaching temperature, and leaching time. Recovery of gold, silver, and palladium of 100%, 81%, and 13% from the WPCB residue sample was achieved by thiourea leaching under optimized conditions. The results show that the efficiency of precious metal dissolution from the WPCB sample using thiourea solution depended strongly on the concentration of both thiourea and oxidant.

  2. Rare and Rare-Earth Metals in Coal Processing Waste

    Directory of Open Access Journals (Sweden)

    Cherkasova Tatiana

    2017-01-01

    Full Text Available An urgent issue for power plants operating on solid fuels (coal is the issue of utilization or use of accumulated production waste - ash and slag materials - in the related production. Ash-slag materials are classified as “waste”, usually grade 5; tens of millions of tons of them being pro-duced annually in the Kemerovo region, which threatens the ecology of the region. At the same time, ash and slag is a very promising raw material. The use of this material as a base for the final product allows us to signifi-cantly expand the possibilities of using coal. The most widespread is the system of ash and slag involving in construction or as a replacement for sand in road construction, or as an additive to building mixtures. However, there are both industrially valuable and environmentally dangerous ele-ments in ash-slag materials. Ash-slag materials can be considered as inde-pendent ore deposits located on the surface and requiring the costs of their extraction.

  3. Study of the leaching of heavy metals from waste water sludge and incinerator's ash, using coupled thermostated columns and DTPA as complex agent; Estudio de la extraccion de metales pesados de lodos y cenizas de aguas residuales usando columnas termostatizadas acopladas y DTPA como agente complejante

    Energy Technology Data Exchange (ETDEWEB)

    Vite T, J.; Vite T, M.; Guerrero D, J.; Carreno de Leon, M.C. [Departamento de Estudios del Ambiente, Instituto Nacional de Investigaciones Nucleares, A.P. 18-1027, 11801 Mexico D.F. (Mexico)

    2000-07-01

    We studied the metallic composition from waste water sludge and incinerators ashes of an incinerator located in Toluca, Mexico, the qualitative studies were made using the Activation Analysis technique, and fluorescence X-ray techniques. The quantitative analysis of heavy metals in the wastes were made using Inductively coupled plasma atomic emission spectrometry (Icp-Aes). For leaching the samples, we used four coupled thermostated columns, each one had a p H of 2,5, 7 and 10. The flux of the air was of 1600 cc/min. The temperature was maintain constant in 60 Centigrade using a thermostated system. For this study we used 100 g of wastes mixed with mineral acid or sodium hydroxide to reach p H 2,5,7 and 10. We added a reducing and tensoactive agents and finally DTPA as complex agent. With this method, we obtain a better leaching efficiency using a complex agent. However the high DTPA cost, make this process expansive that is why we recommend to work with another classes of complex agents, that be cheaper to leach metals of different chemistry matrix. (Author)

  4. Spatial assessment of soil contamination by heavy metals from informal electronic waste recycling in Agbogbloshie, Ghana

    Science.gov (United States)

    Greve, Klaus; Atiemo, Sampson M.

    2016-01-01

    Objectives This study examined the spatial distribution and the extent of soil contamination by heavy metals resulting from primitive, unconventional informal electronic waste recycling in the Agbogbloshie e-waste processing site (AEPS) in Ghana. Methods A total of 132 samples were collected at 100 m intervals, with a handheld global position system used in taking the location data of the soil sample points. Observing all procedural and quality assurance measures, the samples were analyzed for barium (Ba), cadmium (Cd), cobalt (Co), chromium (Cr), copper (Cu), mercury (Hg), nickel (Ni), lead (Pb), and zinc (Zn), using X-ray fluorescence. Using environmental risk indices of contamination factor and degree of contamination (Cdeg), we analyzed the individual contribution of each heavy metal contamination and the overall Cdeg. We further used geostatistical techniques of spatial autocorrelation and variability to examine spatial distribution and extent of heavy metal contamination. Results Results from soil analysis showed that heavy metal concentrations were significantly higher than the Canadian Environmental Protection Agency and Dutch environmental standards. In an increasing order, Pb>Cd>Hg>Cu>Zn>Cr>Co>Ba>Ni contributed significantly to the overall Cdeg. Contamination was highest in the main working areas of burning and dismantling sites, indicating the influence of recycling activities. Geostatistical analysis also revealed that heavy metal contamination spreads beyond the main working areas to residential, recreational, farming, and commercial areas. Conclusions Our results show that the studied heavy metals are ubiquitous within AEPS and the significantly high concentration of these metals reflect the contamination factor and Cdeg, indicating soil contamination in AEPS with the nine heavy metals studied. PMID:26987962

  5. Qualitative and quantitative determination of heavy metals in waste cellular phones.

    Science.gov (United States)

    Maragkos, Konstantinos G; Hahladakis, John N; Gidarakos, Evangelos

    2013-09-01

    Twenty four waste cellular phones, manufactured between 2002 and 2011, were selected in order to determine the total heavy metal content in each of their parts (printed circuit boards (PCBs), plastic housing (PH) and liquid crystal display monitors (LCDs)) and compare the results with the permissible limits set by the 2003 Directive on Restriction of Hazardous Substances (RoHS). All the selected samples were pulverized and digested with strong acids. Inductively coupled plasma-mass spectrometry was used to measure the heavy metal content in each sample. The results revealed that concentration levels of the examined heavy metals were higher in PCBs, followed by PH and LCD in that particular order (PCB>PH>LCD). With the exception of Pb and Cr present in PCBs of mobile phones released before the year 2006, all the other metal concentrations were according to the Directive. Concentration levels of Cd, Hg were lower than the permissible limits set by the EU, either before or after the validity of the 2003 RoHS Directive. Considering their significant heavy metal content, coupled with their large quantities produced worldwide in an annual rate, waste cellular phones need to be treated under an environmentally sound management scheme, prioritizing recycling and at the same time eliminating the possibility of any harm. Copyright © 2013 Elsevier Ltd. All rights reserved.

  6. Retardation factors and dispersion-diffusion coefficients of heavy metals in construction and demolition waste

    Directory of Open Access Journals (Sweden)

    César Reis

    2010-08-01

    Full Text Available Considering the possibility of using the construction and demolition waste (CD as "chemical barrier" to pollutants in landfill, the influence of the CD in the parameters of the transport of heavy metals in the leachate (leached + rainwater infiltrated produced by urban solid waste newly collected was investigated. For this, three size fractions of CD (0.5 to 1; 2 to 4 and 4 to 7.5 mm were used and leachate in the average concentrations of 0.146 mg L-1 for Cu, 0.046 mg L-1 of Cd, 17.2 mg L-1 Zn and 0.135 mg L-1 Pb. The results enabled to conclude that the magnitude of the retardation factors for the metals followed the sequence: Pb>Cu>Zn>Cd; the increase in granulation fractions in BD resulted in smaller retention factor.

  7. A Potential Bio-Sorbent for Heavy Metals in the Remediation of Waste Water

    Directory of Open Access Journals (Sweden)

    Mohammad Laskar

    2016-12-01

    Full Text Available Bay leaves are used for flavoring in cold drinks production, in bakery goods, sauces, confectionary products and liquors. The waste generated from these sources has been valorized by attempting the remediation of waste water. Hence, adsorption of toxic metals onto Bay leaves has been investigated after optimizing the experimental parameters, namely the pH, contact time, adsorbent and Zn (II concentrations as well as the temperature of the equilibrium mixture (consisting of the metal solution in contact with the adsorbent. The participation of the constituent functional groups, of the adsorbent, was ascertained with Fourier Transform spectroscopic studies. The mode of adsorption was examined by employing important isotherm models, namely Langmuir, Freundlich and Dubinin-Radushkevich models. The adsorption process was found to follow pseudo-first order kinetic model and also followed the intraparticle diffusion up to 60 minutes of contact time. The thermodynamic parameters suggest the spontaneous nature of adsorption

  8. Initial Evaluation of Processing Methods for an Epsilon Metal Waste Form

    Energy Technology Data Exchange (ETDEWEB)

    Crum, Jarrod V.; Strachan, Denis M.; Zumhoff, Mac R.

    2012-06-11

    During irradiation of nuclear fuel in a reactor, the five metals, Mo, Pd, Rh, Ru, and Tc, migrate to the fuel grain boundaries and form small metal particles of an alloy known as epsilon metal ({var_epsilon}-metal). When the fuel is dissolved in a reprocessing plant, these metal particles remain behind with a residue - the undissolved solids (UDS). Some of these same metals that comprise this alloy that have not formed the alloy are dissolved into the aqueous stream. These metals limit the waste loading for a borosilicate glass that is being developed for the reprocessing wastes. Epsilon metal is being developed as a waste form for the noble metals from a number of waste streams in the aqueous reprocessing of used nuclear fuel (UNF) - (1) the {var_epsilon}-metal from the UDS, (2) soluble Tc (ion-exchanged), and (3) soluble noble metals (TRUEX raffinate). Separate immobilization of these metals has benefits other than allowing an increase in the glass waste loading. These materials are quite resistant to dissolution (corrosion) as evidenced by the fact that they survive the chemically aggressive conditions in the fuel dissolver. Remnants of {var_epsilon}-metal particles have survived in the geologically natural reactors found in Gabon, Africa, indicating that they have sufficient durability to survive for {approx} 2.5 billion years in a reducing geologic environment. Additionally, the {var_epsilon}-metal can be made without additives and incorporate sufficient foreign material (oxides) that are also present in the UDS. Although {var_epsilon}-metal is found in fuel and Gabon as small particles ({approx}10 {micro}m in diameter) and has survived intact, an ideal waste form is one in which the surface area is minimized. Therefore, the main effort in developing {var_epsilon}-metal as a waste form is to develop a process to consolidate the particles into a monolith. Individually, these metals have high melting points (2617 C for Mo to 1552 C for Pd) and the alloy is

  9. Pollution control and resource reuse for alkaline hydrometallurgy of amphoteric metal hazardous wastes

    CERN Document Server

    Youcai, Zhao

    2017-01-01

    This book provides a comprehensive description of alkaline hydrometallurgy of amphoteric metal hazardous wastes. Topics focus on leaching of zinc and lead hazardous wastes, purification of leach solution of zinc and lead, electrowinning of zinc and lead from purified alkaline solutions, chemical reactions taking place in the production flowsheets, thermodynamic and spent electrolyte regeneration, alkaline hydrometallurgy of low-grade smithsonite ores, recovery of molybdenum and tungsten using ion flotation and solvent extraction processes and their application in chemical synthesis of Nb and Ta inorganic compounds, and industrial scale production of 1500-2000 t/a zinc powder using alkaline leaching–electrowinning processes. Processes described are cost-effective, generate lesser secondary pollutants, and have been applied widely in China. Readers that will find the book appealing include solid waste engineers, environmental managers, technicians, recycling coordinators, government officials, undergraduates ...

  10. Heavy metal uptake from municipal waste compost by the earthworm Eisenia foetida (Savigny 1826)

    Energy Technology Data Exchange (ETDEWEB)

    Fleckenstein, J.; Graff, O.

    1982-01-01

    The uptake of heavy metals and toxic elements by the adult earthworms Eisenia foetida kept in municipal waste compost for 55 and 104 days and by the juveniles was investigated. The uptake of Cu, Zn and Ni increased to constant levels, which appear to be regulated by the physiology of the earthworms. In contrary to this Cd, Hg and As continued to accumulate in the tissues of the earthworms throughout the exposure time. The Pb concentration ratio increased also, but was low (< 0.05). The living conditions for the earthworms in municipal waste compost were satisfactory but the results demonstrate that their use for biological conversion of waste compost to biomass for further animal nutrition is limited by the accumulation of cadmium and mercury.

  11. Perovskite-Ni composite: a potential route for management of radioactive metallic waste.

    Science.gov (United States)

    Mahadik, Pooja Sawant; Sengupta, Pranesh; Halder, Rumu; Abraham, G; Dey, G K

    2015-04-28

    Management of nickel - based radioactive metallic wastes is a difficult issue. To arrest the release of hazardous material to the environment it is proposed to develop perovskite coating for the metallic wastes. Polycrystalline BaCe0.8Y0.2O3-δ perovskite with orthorhombic structure has been synthesized by sol-gel route. Crystallographic analyses show, the perovskite belong to orthorhombic Pmcn space group at room temperature, and gets converted to orthorhombic Incn space group at 623K, cubic Pm3m space group (with a=4.434Å) at 1173K and again orthorhombic Pmcn space group at room temperature after cooling. Similar observations have been made from micro-Raman study as well. Microstructural studies of BaCe0.8Y0.2O3-δ-NiO/Ni composites showed absence of any reaction product at the interface. This suggests that both the components (i.e. perovskite and NiO/Ni) of the composite are compatible to each other. Interaction of BaCe0.8Y0.2O3-δ-NiO/Ni composites with simulated barium borosilicate waste glass melt also did not reveal any reaction product at the interfaces. Importantly, uranium from the waste glass melt was found to be partitioned within BaCe0.8Y0.2O3-δ perovskite structure. It is therefore concluded that BaCe0.8Y0.2O3-δ can be considered as a good coating material for management of radioactive Ni based metallic wastes. Copyright © 2015 Elsevier B.V. All rights reserved.

  12. Informal e-waste recycling: environmental risk assessment of heavy metal contamination in Mandoli industrial area, Delhi, India.

    Science.gov (United States)

    Pradhan, Jatindra Kumar; Kumar, Sudhir

    2014-01-01

    Nowadays, e-waste is a major source of environmental problems and opportunities due to presence of hazardous elements and precious metals. This study was aimed to evaluate the pollution risk of heavy metal contamination by informal recycling of e-waste. Environmental risk assessment was determined using multivariate statistical analysis, index of geoaccumulation, enrichment factor, contamination factor, degree of contamination and pollution load index by analysing heavy metals in surface soils, plants and groundwater samples collected from and around informal recycling workshops in Mandoli industrial area, Delhi, India. Concentrations of heavy metals like As (17.08 mg/kg), Cd (1.29 mg/kg), Cu (115.50 mg/kg), Pb (2,645.31 mg/kg), Se (12.67 mg/kg) and Zn (776.84 mg/kg) were higher in surface soils of e-waste recycling areas compared to those in reference site. Level exceeded the values suggested by the US Environmental Protection Agency (EPA). High accumulations of heavy metals were also observed in the native plant samples (Cynodon dactylon) of e-waste recycling areas. The groundwater samples collected form recycling area had high heavy metal concentrations as compared to permissible limit of Indian Standards and maximum allowable limit of WHO guidelines for drinking water. Multivariate analysis and risk assessment studies based on total metal content explains the clear-cut differences among sampling sites and a strong evidence of heavy metal pollution because of informal recycling of e-waste. This study put forward that prolonged informal recycling of e-waste may accumulate high concentration of heavy metals in surface soils, plants and groundwater, which will be a matter of concern for both environmental and occupational hazards. This warrants an immediate need of remedial measures to reduce the heavy metal contamination of e-waste recycling sites.

  13. Yucca Mountain project canister material corrosion studies as applied to the electrometallurgical treatment metallic waste form

    Energy Technology Data Exchange (ETDEWEB)

    Keiser, D.D.

    1996-11-01

    Yucca Mountain, Nevada is currently being evaluated as a potential site for a geologic repository. As part of the repository assessment activities, candidate materials are being tested for possible use as construction materials for waste package containers. A large portion of this testing effort is focused on determining the long range corrosion properties, in a Yucca Mountain environment, for those materials being considered. Along similar lines, Argonne National Laboratory is testing a metallic alloy waste form that also is scheduled for disposal in a geologic repository, like Yucca Mountain. Due to the fact that Argonne`s waste form will require performance testing for an environment similar to what Yucca Mountain canister materials will require, this report was constructed to focus on the types of tests that have been conducted on candidate Yucca Mountain canister materials along with some of the results from these tests. Additionally, this report will discuss testing of Argonne`s metal waste form in light of the Yucca Mountain activities.

  14. Enhanced bioleaching efficiency of metals from E-wastes driven by biochar

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Shuhua; Zheng, Yue; Yan, Weifu; Chen, Lixiang [CAS Key Laboratory of Urban Pollutant Conversion, Institute of Urban Environment, Chinese Academy of Sciences, Xiamen, 361021 (China); University of Chinese Academy of Sciences, Beijing, 100049 (China); Dummi Mahadevan, Gurumurthy [CAS Key Laboratory of Urban Pollutant Conversion, Institute of Urban Environment, Chinese Academy of Sciences, Xiamen, 361021 (China); Zhao, Feng, E-mail: fzhao@iue.ac.cn [CAS Key Laboratory of Urban Pollutant Conversion, Institute of Urban Environment, Chinese Academy of Sciences, Xiamen, 361021 (China)

    2016-12-15

    Electronic wastes (E-wastes) contain a huge amount of valuable metals that are worth recovering. Bioleaching has attracted widespread attention as an environment-friendly and low-cost technology for the recycling of E-wastes. To avoid the disadvantages of being time-consuming or having a relatively low efficiency, biochar with redox activity was used to enhance bioleaching efficiency of metals from a basic E-waste (i.e., printed circuit boards in this study). The role of biochar was examined through three basic processes: Carbon-mediated, Sulfur-mediated and Iron-mediated bioleaching pathways. Although no obvious enhancement of bioleaching performance was observed in the C-mediated and S-mediated systems, Fe-mediated bioleaching was significantly promoted by the participation of biochar, and its leaching time was decreased by one-third compared with that of a biochar-free system. By mapping the dynamic concentration of Fe(II) and Cu(II), biochar was proved to facilitate the redox action between Fe(II) to Fe(III), which resulted in effective leaching of Cu. Two dominant functional species consisting of Alicyclobacillus spp. and Sulfobacillus spp. may cooperate in the Fe-mediated bioleaching system, and the ratio of these two species was regulated by biochar for enhancing the efficiency of bioleaching. Hence, this work provides a method to improve bioleaching efficiency with low-cost solid redox media.

  15. Evaluation of physical, chemical and heavy metal concentration of food waste composting

    Directory of Open Access Journals (Sweden)

    Abdul Kadir Aeslina

    2017-01-01

    Full Text Available In this study, food waste composting with rice husk and coconut fibre as compost medium were carried out. Two types of different fermentation liquids were prepared which were fermented liquid (banana peel and fermented liquid from fermented soybeans. During the composting process, a compost samples for a twenty week duration at an interval time of two weeks. Among the physico-chemical parameters that were tested were temperature, moisture content, pH value, Total Nitrogen, Total Phosphorous, Potassium and Total Organic Carbon and Carbon Nitrogen ratio. Heavy metals such as copper, cadmium, lead, nickel and arsenic were observed and analysed. From this study, it was found that, the temperature increased during the thermophilic phase while there was gradually increase of Total Nitrogen, Total Phosphorous and Potassium from the beginning till the end of the composting process. It was also found that the total organic carbon (TOC and the carbon nitrogen ratio decreased significantly during the decomposition process. Traces amounts of heavy metals were also detected and remains below the standard Malaysian Environmental regulations. It was concluded that, the composting process was faster with processed food waste followed by combination of processed food waste and raw. Raw food waste were demonstrated the lowest degradation rate.

  16. Native fungi as metal remediators: Silver myco-accumulation from metal contaminated waste-rock dumps (Libiola Mine, Italy).

    Science.gov (United States)

    Cecchi, Grazia; Marescotti, Pietro; Di Piazza, Simone; Zotti, Mirca

    2017-03-04

    Metal contamination constitutes a major source of pollution globally. Many recent studies emphasized the need to develop cheap and green technologies for the remediation or reclamation of environmental matrices contaminated by heavy metals. In this context, fungi are versatile organisms that can be exploited for bioremediation activities. In our work, we tested silver (Ag) bioaccumulation capabilities of three microfungal strains (Aspergillus alliaceus Thom & Church, Trichoderma harzianum Rifai, Clonostachys rosea (Link) Schroers, Samuels, Seifert & W. Gams) isolated from a silver polluted site. The aim was to select silver tolerant native strains and test their potential silver uptake. Among the three species tested, T. harzianum was the most efficient strain to tolerate and accumulate silver, showing an uptake capability of 153 mg L(-1) taken at the Ag concentration of 330 mg L(-1). Our study highlights the potential use of native microfungi spontaneously growing in sulphide-rich waste rock dumps, for silver bioaccumulation and bioremediation.

  17. Capture of organic iodides from nuclear waste by metal-organic framework-based molecular traps.

    Science.gov (United States)

    Li, Baiyan; Dong, Xinglong; Wang, Hao; Ma, Dingxuan; Tan, Kui; Jensen, Stephanie; Deibert, Benjamin J; Butler, Joseph; Cure, Jeremy; Shi, Zhan; Thonhauser, Timo; Chabal, Yves J; Han, Yu; Li, Jing

    2017-09-07

    Effective capture of radioactive organic iodides from nuclear waste remains a significant challenge due to the drawbacks of current adsorbents such as low uptake capacity, high cost, and non-recyclability. We report here a general approach to overcome this challenge by creating radioactive organic iodide molecular traps through functionalization of metal-organic framework materials with tertiary amine-binding sites. The molecular trap exhibits a high CH 3 I saturation uptake capacity of 71 wt% at 150 °C, which is more than 340% higher than the industrial adsorbent Ag 0 @MOR under identical conditions. These functionalized metal-organic frameworks also serve as good adsorbents at low temperatures. Furthermore, the resulting adsorbent can be recycled multiple times without loss of capacity, making recyclability a reality. In combination with its chemical and thermal stability, high capture efficiency and low cost, the adsorbent demonstrates promise for industrial radioactive organic iodides capture from nuclear waste. The capture mechanism was investigated by experimental and theoretical methods.Capturing radioactive organic iodides from nuclear waste is important for safe nuclear energy usage, but remains a significant challenge. Here, Li and co-workers fabricate a stable metal-organic framework functionalized with tertiary amine groups that exhibits high capacities for radioactive organic iodides uptake.

  18. Non-Ferrous Metal Industry Waste Disposal Sites As A Source Of Poly-Extremotolerant Bacteria

    Directory of Open Access Journals (Sweden)

    Pristas Peter

    2015-06-01

    Full Text Available Waste disposal sites from non-ferrous metal industry constitute environments very hostile for life due to the presence of very specialized abiotic factors (pH, salt concentration, heavy metals content. In our experiments microflora of two waste disposal sites in Slovakia – brown mud disposal site from aluminium production near Ziar nad Hronom and nickel sludge disposal site near Sered - was analyzed for cultivable bacteria. Isolated bacteria were characterized by a combination of classical microbiological approaches and molecular methods and the most of isolated bacteria shown a poly-extremotolerant phenotype. The most frequently halotolerant (resistant to the high level of salt concentrations and alkalitolerant (resistant to the high pH level bacteria belonging to the Actinobacteria class were detected. The most of bacteria shown very high level of heavy metal resistance e.g. more than 500 μg/ml for Zn2+ or Cu2+. Based on our data, waste disposal sites thus on one side represents an important environmental burden but on other side they are a source of new poly-extremotolerant bacterial strains and species possibly used in many biotechnology and bioremediation applications.

  19. Capture of organic iodides from nuclear waste by metal-organic framework-based molecular traps

    KAUST Repository

    Li, Baiyan

    2017-09-01

    Effective capture of radioactive organic iodides from nuclear waste remains a significant challenge due to the drawbacks of current adsorbents such as low uptake capacity, high cost, and non-recyclability. We report here a general approach to overcome this challenge by creating radioactive organic iodide molecular traps through functionalization of metal-organic framework materials with tertiary amine-binding sites. The molecular trap exhibits a high CH3I saturation uptake capacity of 71 wt% at 150 °C, which is more than 340% higher than the industrial adsorbent Ag0@MOR under identical conditions. These functionalized metal-organic frameworks also serve as good adsorbents at low temperatures. Furthermore, the resulting adsorbent can be recycled multiple times without loss of capacity, making recyclability a reality. In combination with its chemical and thermal stability, high capture efficiency and low cost, the adsorbent demonstrates promise for industrial radioactive organic iodides capture from nuclear waste. The capture mechanism was investigated by experimental and theoretical methods.Capturing radioactive organic iodides from nuclear waste is important for safe nuclear energy usage, but remains a significant challenge. Here, Li and co-workers fabricate a stable metal-organic framework functionalized with tertiary amine groups that exhibits high capacities for radioactive organic iodides uptake.

  20. Development of steel plate - cast iron hybrid casting process for recycling of low level radioactive metal waste

    Energy Technology Data Exchange (ETDEWEB)

    Nakamura, H.; Hirabayashi, T. [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan); Akimoto, J.; Takahashi, K.; Shindo, H.; Sakurai, D. [Mitsubishi Materials Corp., Tokyo (Japan); Almansour, A.; Okane, T.; Umeda, T. [Univ. of Tokyo (Japan)

    2000-07-01

    For the purposes of recycling low-level radioactive waste arising from dismantling of nuclear reactors, applicability of steel plate - cast iron hybrid casting process has been investigated as a measure for producing a waste container using radioactive metal waste. This investigation consists of casting tests and analyses on the solidification and distortion of castings. This paper describes the concept of the casting process, casting test results, and understandings obtained from the analyses. (orig.)

  1. Dimethylamine-modified waste paper for the recovery of precious metals.

    Science.gov (United States)

    Adhikari, Chaitanya Raj; Parajuli, Durga; Kawakita, Hidetaka; Inoue, Katsutoshi; Ohto, Keisuke; Harada, Hiroyuki

    2008-08-01

    Waste newsprint paper was modified with dimethylamine (DMA) to obtain a tertiary amine type adsorption gel called DMA-paper gel. This new derivative was investigated for adsorption, from hydrochloric acid medium, of gold, palladium, and platinum as well as some base metals. The gel exhibited selectivity only for precious metals with a remarkably high capacity for Au(III), i.e., 4.6 mol/kg dry gel and comparable capacities, i.e., 2.1 and 0.9 mol/kg for Pd(II) and Pt(IV), respectively. Also, Au(III) was reduced to the elemental form during adsorption. Furthermore, column adsorption and subsequent elution of the adsorbed metal ions by acidic thiourea revealed encouraging recoveries (approximately 90%), thus enhancing the scope of the gel for effective preconcentration, separation, and recovery of precious metals. The effectiveness of recovery of precious metals from real industrial liquor was also tested, and it showed highly encouraging results with respect to the stability of the gel in the harsh medium, and selectivity for the targeted metal ions in the presence of excess of other metal ions.

  2. Treatment of metallurgical wastes : recovery of metal values from smelter slags by pressure oxidative leaching

    Energy Technology Data Exchange (ETDEWEB)

    Li, Y.; Perederiy, I.; Papangelakis, V.G. [Toronto Univ., ON (Canada). Dept. of Chemical Engineering and Applied Chemistry

    2008-07-01

    Vast quantities of slag are produced and dumped as waste by-products during the production of base metals by smelting operations. These slags contain large amounts of valuable metals which lead to a decrease in metal yield and, combined with the entrapped sulphur, pose a danger to the environment. The dissolution of fayalite is important for the selective recovery of valuable metals and the cleanup of slags in high pressure oxidative leaching. The nature of base metals and iron in solidified slag must be investigated in order to understand the mechanism of the process. This paper discussed the application of powder X-ray diffraction (PXRD) and scanning electron microscopy (SEM) for the characterization of a smelter slag microstructure. The study used leaching tests with the same smelter slag to measure and monitor the results of leaching, including metal extraction levels, the extent of iron dissolution as well as impurity contents. The paper provided information on the experiment with particular reference to slag leaching, chemical analysis, and characterization. It was concluded that slag consists of several solid phases with base metal sulfide and oxide droplets entrapped in the fayalite matrix or silica regions. Therefore, nickel, copper, cobalt, and zinc need to be exposed either chemically or mechanically to promote their recovery. 21 refs., 4 tabs., 5 figs.

  3. Innovative approach for the valorization of useful metals from waste electric and electronic equipment (WEEE)

    Science.gov (United States)

    Soare, V.; Burada, M.; Dumitrescu, D. V.; Constantin, I.; Soare, V.; Popescu, A.-M. J.; Carcea, I.

    2016-08-01

    Waste electric and electronic equipment are an important secondary source of rare and precious metals and their processing through ecological technologies constitutes a major concern in the European Union and significantly contributes to the reduction of environmental pollution and to the preservation of valuable resources of nonferrous metals. The paper presents an innovative approach for the complex valorization of useful metals contained in WEEE. The method consists in the melting of WEEE in a furnace in a microwave field at temperatures of 1000 ÷1200°C, for the complete separation of the metallic fraction from the organic components. The gases resulting from the melting process were also treated/neutralized in a microwave environment and the obtained metallic bulk (multi-component alloy) was processed through combined hydrometallurgical and electrochemical methods. The major elements in the metallic bulk (Cu, Sn, Zn, Pb) were separated/recovered by anodic dissolution, respectively by leaching in nitric acid followed by cementation using various agents, or by electrodeposition. Depending on the electrochemical parameters, cathodic deposits consisting of Cu, with a purity higher than 99.9%, or of Cu-Sn and Cu-Sn-Zn alloys were obtained. Silver was valorized by leaching/precipitation with NaCl and the gold concentrated in the anodic slime will be recovered by thiourea extraction. The experiments performed demonstrate the possibility of ecological and efficient processing of WEEE in a microwave field and the recovery of nonferrous and precious metals through combined hydrometallurgical and electrochemical methods.

  4. Heavy metal contamination of soil and water in the vicinity of an abandoned e-waste recycling site: implications for dissemination of heavy metals.

    Science.gov (United States)

    Wu, Qihang; Leung, Jonathan Y S; Geng, Xinhua; Chen, Shejun; Huang, Xuexia; Li, Haiyan; Huang, Zhuying; Zhu, Libin; Chen, Jiahao; Lu, Yayin

    2015-02-15

    Illegal e-waste recycling activity has caused heavy metal pollution in many developing countries, including China. In recent years, the Chinese government has strengthened enforcement to impede such activity; however, the heavy metals remaining in the abandoned e-waste recycling site can still pose ecological risk. The present study aimed to investigate the concentrations of heavy metals in soil and water in the vicinity of an abandoned e-waste recycling site in Longtang, South China. Results showed that the surface soil of the former burning and acid-leaching sites was still heavily contaminated with Cd (>0.39 mg kg(-1)) and Cu (>1981 mg kg(-1)), which exceeded their respective guideline levels. The concentration of heavy metals generally decreased with depth in both burning site and paddy field, which is related to the elevated pH and reduced TOM along the depth gradient. The pond water was seriously acidified and contaminated with heavy metals, while the well water was slightly contaminated since heavy metals were mostly retained in the surface soil. The use of pond water for irrigation resulted in considerable heavy metal contamination in the paddy soil. Compared with previous studies, the reduced heavy metal concentrations in the surface soil imply that heavy metals were transported to the other areas, such as pond. Therefore, immediate remediation of the contaminated soil and water is necessary to prevent dissemination of heavy metals and potential ecological disaster. Copyright © 2014 Elsevier B.V. All rights reserved.

  5. Effects of slag composition and process variables on decontamination of metallic wastes by melt refining

    Energy Technology Data Exchange (ETDEWEB)

    Heshmatpour, B.; Copeland, G. L.

    1981-01-01

    Melt refining has been suggested as an alternative for decontamination and volume reduction of low-level-contaminated metallic wastes. Knowledge of metallurgical and thermochemical aspects of the process is essential for effective treatment of various metals. Variables such as slag type and composition, melting technique, and refractory materials need to be identified for each metal or alloy. Samples of contaminated metals were melted with fluxes by resistance furnace or induction heating. The resulting ingots as well as the slags were analyzed for their nuclide contents, and the corresponding partition ratios were calculated. Compatibility of slags and refractories was also investigated, and proper refractory materials were identified. Resistance furnace melting appeared to be a better melting technique for nonferrous scrap, while induction melting was more suitable for ferrous metals. In general uranium contents of the metals, except for aluminum, could be reduced to as low as 0.01 to 0.1 ppM by melt refining. Aluminum could be decontaminated to about 1 to 2 ppM U when certain fluoride slags were used. The extent of decontamination was not very sensitive to slag type and composition. However, borosilicate and basic oxidizing slags were more effective on ferrous metals and Cu; NaNO/sub 3/-NaCl-NaOH type fluxes were desirable for Zn, Pb, and Sn; and fluoride type slags were effective for decontamination of Al. Recrystallized alumina proved to be the most compatible refractory for melt refining both ferrous and nonferrous metals, while graphite was suitable for nonferrous metal processing. In conclusion, melt refining is an effective technique for volume reduction ad decontamination of contaminated metal scrap when proper slags, melting technique, and refractories are used.

  6. Assessing metal contamination from construction and demolition (C&D) waste used to infill wetlands: using Deroceras reticulatum (Mollusca: Gastropoda).

    Science.gov (United States)

    Staunton, John A; Mc Donnell, Rory J; Gormally, Michael J; Williams, Chris D; Henry, Tiernan; Morrison, Liam

    2014-11-01

    Large quantities of construction and demolition waste (C&D) are produced globally every year, with little known about potential environmental impacts. In the present study, the slug, Deroceras reticulatum (Mollusca: Gastropoda) was used as the first biomonitor of metals (Ag, As, Ba, Cd, Co, Cr, Cu, Mn, Mo, Ni, Pb, Sb, Se, Ti, Tl, V and Zn) on wetlands post infilling with construction and demolition (C&D) waste. The bioaccumulation of As, Ba, Cd, Co, Sb, Se and Tl were found to be significantly elevated in slugs collected on C&D waste when compared to unimproved pastures (control sites), while Mo, Se and Sr had significantly higher concentrations in slugs collected on C&D waste when compared to known contaminated sites (mining locations), indicating the potential hazardous nature of C&D waste to biota. Identifying exact sources for these metals within the waste can be problematic, due to its heterogenic nature. Biomonitors are a useful tool for future monitoring and impact studies, facilitating policy makers and regulations in other countries regarding C&D waste infill. In addition, improving separation of C&D waste to allow increased reuse and recycling is likely to be effective in reducing the volume of waste being used as infill, subsequently decreasing potential metal contamination.

  7. The concentrations of trace metals in plants from phosphogypsum waste heap in Wiślinka, northern Poland

    Directory of Open Access Journals (Sweden)

    Boryło A.

    2013-04-01

    Full Text Available The aim of this work was determination of trace metals (Pb, Zn, Ni, Cu and Fe in different plants collected in the vicinity of phosphogypsum waste heap in Wiślinka (northern Poland. The concentrations of trace metals were determined by two methods: AAS (atomic absorption spectrometry and OES-ICP (atomic emission spectrometry with inductively coupled plasma. Enhanced levels of iron were observed in all the analyzed samples. This fact can be explained by the higher content of iron in the groundwaters of Žuławy Wiślane, where concentration of iron was 60 mg/l. The trace metals concentrations in plant samples from phosphogypsum waste heap recorded in this study are generally higher than in control sites. In this study the relationship is shown between atmospheric trace metals deposition and elevated trace metals element concentrations in plants and topsoils, especially in the vicinity of phoshpogypsum waste heap.

  8. Valorization of food waste into hydroxymethylfurfural: Dual role of metal ions in successive conversion steps.

    Science.gov (United States)

    Yu, Iris K M; Tsang, Daniel C W; Yip, Alex C K; Chen, Season S; Ok, Yong Sik; Poon, Chi Sun

    2016-11-01

    This study aimed to transform food waste into a value-added chemical, hydroxymethylfurfural (HMF), and unravel the tangled effects induced by the metal catalysts on each single step of the successive conversion pathway. The results showed that using cooked rice and bread crust as surrogates of starch-rich food waste, yields of 8.1-9.5% HMF and 44.2-64.8% glucose were achieved over SnCl4 catalyst. Protons released from metal hydrolysis and acidic by-products rendered Brønsted acidity to catalyze fructose dehydration and hydrolysis of glycosidic bond. Lewis acid site of metals could facilitate both fructose dehydration and glucose isomerization via promoting the rate-limiting internal hydride shift, with the catalytic activity determined by its electronegativity, electron configuration, and charge density. Lewis acid site of a higher valence also enhanced hydrolysis of polysaccharide. However, the metals also catalyzed undesirable polymerization possibly by polarizing the carbonyl groups of sugars and derivatives, which should be minimized by process optimization. Copyright © 2016 Elsevier Ltd. All rights reserved.

  9. Investigation of heavy metal partitioning influenced by flue gas moisture and chlorine content during waste incineration.

    Science.gov (United States)

    Li, Qinghai; Meng, Aihong; Jia, Jinyan; Zhang, Yanguo

    2010-01-01

    The impact of moisture on the partitioning of the heavy metals including Pb, Zn, Cu and Cd in municipal solid waste (MSW) was studied in a laboratory tubular furnace. A thermodynamic investigation using CHEMKIN software was performed to compare the experimental results. Simulated waste, representative of typical MSW with and without chlorine compounds, was burned at the background temperature of 700 and 950 degrees C, respectively. In the absence of chlorine, the moisture content has no evident effect on the volatility of Pb, Zn and Cu at either 700 or 950 degrees C, however, as flue gas moisture increasing the Cd distribution in the bottom ash increased at 700 degrees C and reduced at 950 degrees C, respectively. In the presence of chlorine, the flue gas moisture reduced the volatility of Pb, Zn and Cu due to the transformation of the more volatile metal chlorides into less volatile metal oxides, and the reduction became significant as chlorine content increase. For Cd, the chlorine promotes its volatility through the formation of more volatile CdCl2. As a result, the increased moisture content increases the Pb, Zn, Cu and Cd concentrations in the bottom ash, which limits the utilization of the bottom ash as a construction material. Therefore, in order to accumulate heavy metals into the fly ash, MSW should be dried before incineration.

  10. Metal recovery by bioleaching of sulfidic mining wastes — Application to a European case study

    Science.gov (United States)

    Guézennec, A. G.; Jacob, J.; Joulian, C.; Dupraz, S.; Menard, Y.; d'Hugues, P.

    The non-energy extractive industry (NEEI) of the EU-25 generated a direct turnover of about €40 billion, and provided employment to about 250000 people in 16629 companies in 2004. The use of primary raw materials in the production of other branches of EU industry means they have a central role in guaranteeing industrial and economic sustainability. Nevertheless current demand exceeds production, and so the EU is heavily dependent on minerals and metals imports. In this context of securing access to metals, turning mining wastes into new resources of currently unexploited valuable metals is an important challenge. The mining wastes can contain base and precious metals, but also metalloids and rare earth elements that are nowadays considered as highly critical for the industrial development of the European Union. Nevertheless, the development of alternative routes to conventional processing is still required in order to decrease the cost associated to the treatment of these unconventional resources which are more complex in composition and with lower grades.

  11. Environmental effects of heavy metals derived from the e-waste recycling activities in China: a systematic review.

    Science.gov (United States)

    Song, Qingbin; Li, Jinhui

    2014-12-01

    As the world's leading manufacturing country, China has become the largest dumping ground for e-waste, resulting in serious pollution of heavy metals in China. This study reviews recent studies on environmental effects of heavy metals from the e-waste recycling sites in China, especially Taizhou, Guiyu, and Longtang. The intensive uncontrolled processing of e-waste in China has resulted in the release of large amounts of heavy metals in the local environment, and caused high concentrations of metals to be present in the surrounding air, dust, soils, sediments and plants. Though the pollution of many heavy metals was investigated in the relevant researches, the four kinds of heavy metals (Cu, Pb, Cd and Cr) from e-waste recycling processes attracted more attention. The exceedance of various national and international standards imposed negative effects to the environment, which made the local residents face with the serious heavy metal exposure. In order to protect the environment and human health, there is an urgent need to control and monitor the informal e-waste recycling operations. Copyright © 2014 Elsevier Ltd. All rights reserved.

  12. Formal recycling of e-waste leads to increased exposure to toxic metals: an occupational exposure study from Sweden.

    Science.gov (United States)

    Julander, Anneli; Lundgren, Lennart; Skare, Lizbet; Grandér, Margaretha; Palm, Brita; Vahter, Marie; Lidén, Carola

    2014-12-01

    Electrical and electronic waste (e-waste) contains multiple toxic metals. However, there is currently a lack of exposure data for metals on workers in formal recycling plants. The objective of this study was to evaluate workers' exposure to metals, using biomarkers of exposure in combination with monitoring of personal air exposure. We assessed exposure to 20 potentially toxic metals among 55 recycling workers and 10 office workers at three formal e-waste recycling plants in Sweden. Workers at two of the plants were followed-up after 6 months. We collected the inhalable fraction and OFC (37-mm) fraction of particles, using personal samplers, as well as spot samples of blood and urine. We measured metal concentrations in whole blood, plasma, urine, and air filters using inductively coupled plasma-mass spectrometry following acid digestion. The air sampling indicated greater airborne exposure, 10 to 30 times higher, to most metals among the recycling workers handling e-waste than among the office workers. The exposure biomarkers showed significantly higher concentrations of chromium, cobalt, indium, lead, and mercury in blood, urine, and/or plasma of the recycling workers, compared with the office workers. Concentrations of antimony, indium, lead, mercury, and vanadium showed close to linear associations between the inhalable particle fraction and blood, plasma, or urine. In conclusion, our study of formal e-waste recycling shows that workers performing recycling tasks are exposed to multiple toxic metals. Copyright © 2014. Published by Elsevier Ltd.

  13. Effective removal and recovery of antimony using metal-loaded saponified orange waste.

    Science.gov (United States)

    Biswas, Biplob Kumar; Inoue, Jun-ichi; Kawakita, Hidetaka; Ohto, Keisuke; Inoue, Katsutoshi

    2009-12-30

    Zr(IV) and Fe(III) ions were loaded onto an orange waste precursor to prepare a metal-loaded orange waste gel, which was investigated for the adsorptive removal and recovery of antimony (III and V) from an aqueous environment. The loading capacity of the orange waste for Zr(IV) and Fe(III) was found to be 1.40 and 1.87 mmol/g, respectively. The maximum batch mode sorption capacity of the Zr(III)-loaded saponified orange waste (SOW) gel was found to be 0.94 mmol/g for Sb(III) and 1.19 mmol/g for Sb(V). A nearly similar result was found for the Fe(III)-loaded SOW gel with the sorption capacity for Sb(III) and Sb(V) being 1.12 and 1.19 mmol/g, respectively. The presence of a variety of anionic species such as carbonate, chloride, nitrate and sulfate had no influence on the adsorption of both Sb(III) and Sb(V). A column adsorption-elution test demonstrated the utility of this system in continuous mode. Selective sulfide precipitation of antimony is one of the major findings in the present work, which clearly suggests a means of effective recovery of antimony from solution containing antimony and other metal ions. Due to their low cost, availability and significantly high adsorption capacity, the metal-loaded gels are expected to be effectively employed for the removal and recovery of antimony from aqueous solution, thus leading to the establishment of a greener environment.

  14. METAL TOLERANCE ANALYSIS OF MICROFUNGI ISOLATED FROM METAL CONTAMINATED SOIL AND WASTE WATER

    Directory of Open Access Journals (Sweden)

    Mathan Jayaraman

    2014-08-01

    Full Text Available The influence of Cr6+, Pb2+, Cu2+, Ni2+, Zn2+ and Cd2+ on the development of 24 fungi was investigated for Metal Tolerance Index (MTI at 1mg ml-1 Cr6+, Pb2+, Cu2+, Ni2+, Zn2+ and Cd2+ concentrations and also for Minimum Inhibitory Concentration (MIC. The MIC ranged from 0.5 to 1.5 mg ml-1 depending on the isolate Aspergillus, Fusarium and Penicillium sp. were tested for their metal tolerance index. Out of these Aspergillus flavus (ED4 shows a better tolerance index of 0.80 Cr6+, 0.72 for Pb2+ , 0.63 for Cu2+, 0.58 for Ni2+, 0.46 for Zn2+ and 0.60 Cd2+ for MIC value for the removal of heavy metals from contaminated soil and wastewaters.

  15. Multiple antibiotic resistances in metal tolerant E. coli from hospital waste water.

    Science.gov (United States)

    Alam, Manzar; Imran, Mohd

    2014-01-01

    Study of antibiotic resistance was done among the metal tolerant E. coli isolates from hospital wastewater at Lucknow city. Metal tolerance was determined in terms of visible growth on metal amended plates at their varying concentrations. MICs were also determined among all metal tolerant E. coli isolates. All the isolates showed their MIC in between 100-2000 µg/ml while maximum isolates demonstrated their MICs at 400, 800 and 1600 µg/ml against all the metal tested. 23.07% of the isolates showed their MIC at 2000 µg/ml against Ni(3+). Multiple antibiotic resistances were recorded among all the metal resistant E.coli isolates. A high level of resistance was observed against Methicillin (86.53%) followed by penicillin (73.07%), Cephradin (57.69%), Rifampicin (34.61%), Erythromycin (26.92%), Nalidixic acids (25%), Chloramphenicol (3.84%) and least to Gentamycine (1.92%). Streptomycin was recorded most effective against E.coli isolates among the entire antibiotic tested. Antimicrobial resistance observed among the bacteria from the aquatic system contaminated with hospital wastes may be threatful for the environment and public health both.

  16. Iodine Sequestration Using Delafossites and Layered Hydroxides

    Energy Technology Data Exchange (ETDEWEB)

    J.D. Pless; J.B. Chwirka; J.L. Krumhansl

    2006-03-28

    The objective of this document is to report on early success for sequestering {sup 129}I. Sorption coefficients (K{sub d}) for I{sup -} and IO{sub 3}{sup -} onto delafossites, spinels and layered metal hydroxides were measured in order to compare their applicability for sequestering {sup 129}I. The studies were performed using a dilute fluid composition representative of groundwater indigenous to the Yucca mountain area. Delafossites generally exhibited relatively poor sorption coefficients (< 10{sup 1.7} mL/g). In contrast, the composition of the layered hydroxides significantly affects their ability to sorb I. Cu/Al and Cu/Cr layered hydroxide samples exhibit K{sub d}'s greater than 10{sup 3} mL/g for both I{sup -} and IO{sub 3}{sup -}.

  17. Recycling of non-metallic fractions from waste electrical and electronic equipment (WEEE): a review.

    Science.gov (United States)

    Wang, Ruixue; Xu, Zhenming

    2014-08-01

    The world's waste electrical and electronic equipment (WEEE) consumption has increased incredibly in recent decades, which have drawn much attention from the public. However, the major economic driving force for recycling of WEEE is the value of the metallic fractions (MFs). The non-metallic fractions (NMFs), which take up a large proportion of E-wastes, were treated by incineration or landfill in the past. NMFs from WEEE contain heavy metals, brominated flame retardant (BFRs) and other toxic and hazardous substances. Combustion as well as landfill may cause serious environmental problems. Therefore, research on resource reutilization and safe disposal of the NMFs from WEEE has a great significance from the viewpoint of environmental protection. Among the enormous variety of NMFs from WEEE, some of them are quite easy to recycle while others are difficult, such as plastics, glass and NMFs from waste printed circuit boards (WPCBs). In this paper, we mainly focus on the intractable NMFs from WEEE. Methods and technologies of recycling the two types of NMFs from WEEE, plastics, glass are reviewed in this paper. For WEEE plastics, the pyrolysis technology has the lowest energy consumption and the pyrolysis oil could be obtained, but the containing of BFRs makes the pyrolysis recycling process problematic. Supercritical fluids (SCF) and gasification technology have a potentially smaller environmental impact than pyrolysis process, but the energy consumption is higher. With regard to WEEE glass, lead removing is requisite before the reutilization of the cathode ray tube (CRT) funnel glass, and the recycling of liquid crystal display (LCD) glass is economically viable for the containing of precious metals (indium and tin). However, the environmental assessment of the recycling process is essential and important before the industrialized production stage. For example, noise and dust should be evaluated during the glass cutting process. This study could contribute

  18. Decreased vaccine antibody titers following exposure to multiple metals and metalloids in e-waste-exposed preschool children

    NARCIS (Netherlands)

    Lin, Xinjiang; Xu, Xijin; Zeng, Xiang; Xu, Long; Zeng, Zhijun; Huo, Xia

    We explored acquired immunity resulting from vaccination in 3 to 7-year-old children, chronically exposed to multiple heavy metals and metalloids, in an e-waste recycling area (Guiyu, China). Child blood levels of ten heavy metals and metalloids, including lead (Pb), arsenic (As), mercury (Hg),

  19. Synthesis of layered double hydroxides from eggshells

    Energy Technology Data Exchange (ETDEWEB)

    Li Songnan [Key Laboratory of Superlight Materials and Surface Technology, Ministry of Education, 150001 (China); Wang Fangyong [College of Engineering and Technology, Northeast Forestry University, 150001 (China); Jing Xiaoyan [Key Laboratory of Superlight Materials and Surface Technology, Ministry of Education, 150001 (China); Wang Jun, E-mail: zhqw1888@sohu.com [Key Laboratory of Superlight Materials and Surface Technology, Ministry of Education, 150001 (China); Saba, Jamil; Liu Qi; Ge Lan; Song Dalei; Zhang Milin [Key Laboratory of Superlight Materials and Surface Technology, Ministry of Education, 150001 (China)

    2012-01-16

    Graphical abstract: This is the XRD pattern and TEM image of 4Ca-Al layered double hydroxide, which is obtained from eggshells. It can be seen that the sample is of layered double hydroxide and shows the plate-like agglomerations with an average size of 20-100 nm. Highlights: Black-Right-Pointing-Pointer We synthesize layered double hydroxides from eggshells. Black-Right-Pointing-Pointer Eggshells are the mainly material in this method. Black-Right-Pointing-Pointer The additional alkaline solution is not required. - Abstract: Ca-Al and Ca-Fe layered double hydroxides (LDHs) were successfully synthesized from chicken eggshells by an ultrasonic wave assistant method. The products were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), and Fourier transform infrared spectroscopy (FT-IR) techniques. XRD and TEM analyses showed that the 4Ca-Al LDHs were of high purity but other samples were not. The present study provides a simple, efficient and environmental friendly method to obtain LDHs from biowaste eggshells, in which additional alkaline solution is not required for synthesis. Moreover, eggshells provide all the requisite bivalent metal ions, which are needed to form layered double hydroxides.

  20. Screening of heavy metal containing waste types for use as raw material in Arctic clay-based bricks

    DEFF Research Database (Denmark)

    Belmonte, Louise Josefine; Ottosen, Lisbeth M.; Kirkelund, Gunvor Marie

    2016-01-01

    particulate waste materials, were fired and material properties and heavy metal leaching tests were conducted before and after firing. Remediation techniques (washing in distilled water and electrodialytical treatment) applied to the fly ash reduced leaching before firing. The mine tailings and bottom ash......In the vulnerable Arctic environment, the impact of especially hazardous wastes can have severe consequences and the reduction and safe handling of these waste types are therefore an important issue. In this study, two groups of heavy metal containing particulate waste materials, municipal solid...... waste incineration (MSWI) fly and bottom ashes and mine tailings (i.e., residues from the mineral resource industry) from Greenland were screened in order to determine their suitability as secondary resources in clay-based brick production. Small clay discs, containing 20 or 40% of the different...

  1. Comparison of soil heavy metal pollution caused by e-waste recycling activities and traditional industrial operations.

    Science.gov (United States)

    He, Kailing; Sun, Zehang; Hu, Yuanan; Zeng, Xiangying; Yu, Zhiqiang; Cheng, Hefa

    2017-04-01

    The traditional industrial operations are well recognized as an important source of heavy metal pollution, while that caused by the e-waste recycling activities, which have sprouted in some developing countries, is often overlooked. This study was carried out to compare the status of soil heavy metal pollution caused by the traditional industrial operations and the e-waste recycling activities in the Pearl River Delta, and assess whether greater attention should be paid to control the pollution arising from e-waste recycling activities. Both the total contents and the chemical fractionation of major heavy metals (As, Cr, Cd, Ni, Pb, Cu, and Zn) in 50 surface soil samples collected from the e-waste recycling areas and 20 soil samples from the traditional industrial zones were determined. The results show that the soils in the e-waste recycling areas were mainly polluted by Cu, Zn, As, and Cd, while Cu, Zn, As, Cd, and Pb were the major heavy metals in the soils from the traditional industrial zones. Statistical analyses consistently show that Cu, Cd, Pb, and Zn in the surface soils from both types of sites were contributed mostly by human activities, while As, Cr, and Ni in the soils were dominated by natural background. No clear distinction was found on the pollution characteristic of heavy metals in the surface soils between the e-waste recycling areas and traditional industrial zones. The potential ecological risk posed by heavy metals in the surface soils from both types of sites, which was dominated by that from Cd, ranged from low to moderate. Given the much shorter development history of e-waste recycling and its largely unregulated nature, significant efforts should be made to crack down on illegal e-waste recycling and strengthen pollution control for related activities.

  2. Modeling packed bed sorbent systems with the Pore Surface Diffusion Model: Evidence of facilitated surface diffusion of arsenate in nano-metal (hydr)oxide hybrid ion exchange media.

    Science.gov (United States)

    Dale, Sachie; Markovski, Jasmina; Hristovski, Kiril D

    2016-09-01

    This study explores the possibility of employing the Pore Surface Diffusion Model (PSDM) to predict the arsenic breakthrough curve of a packed bed system operated under continuous flow conditions with realistic groundwater, and consequently minimize the need to conduct pilot scale tests. To provide the nano-metal (hydr)oxide hybrid ion exchange media's performance in realistic water matrices without engaging in taxing pilot scale testing, the multi-point equilibrium batch sorption tests under pseudo-equilibrium conditions were performed; arsenate breakthrough curve of short bed column (SBC) was predicted by the PSDM in the continuous flow experiments; SBC tests were conducted under the same conditions to validate the model. The overlapping Freundlich isotherms suggested that the water matrix and competing ions did not have any denoting effect on sorption capacity of the media when the matrix was changed from arsenic-only model water to real groundwater. As expected, the PSDM provided a relatively good prediction of the breakthrough profile for arsenic-only model water limited by intraparticle mass transports. In contrast, the groundwater breakthrough curve demonstrated significantly faster intraparticle mass transport suggesting to a surface diffusion process, which occurs in parallel to the pore diffusion. A simple selection of DS=1/2 DP appears to be sufficient when describing the facilitated surface diffusion of arsenate inside metal (hydr)oxide nano-enabled hybrid ion-exchange media in presence of sulfate, however, quantification of the factors determining the surface diffusion coefficient's magnitude under different treatment scenarios remained unexplored. Copyright © 2015 Elsevier B.V. All rights reserved.

  3. Scoping evaluation of the technical capabilities of DOE sites for disposal of hazardous metals in mixed low-level waste

    Energy Technology Data Exchange (ETDEWEB)

    Gruebel, M.M.; Waters, R.D.; Langkopf, B.S.

    1997-05-01

    A team of analysts designed and conducted a scoping evaluation to estimate the technical capabilities of fifteen Department of Energy sites for disposal of the hazardous metals in mixed low-level waste (i.e., waste that contains both low-level radioactive materials and hazardous constituents). Eight hazardous metals were evaluated: arsenic, barium, cadmium, chromium, lead, mercury, selenium, and silver. The analysis considered transport only through the groundwater pathway. The results are reported as site-specific estimates of maximum concentrations of each hazardous metal in treated mixed low-level waste that do not exceed the performance measures established for the analysis. Also reported are site-specific estimates of travel times of each hazardous metal to the point of compliance.

  4. Impact of fluidized bed combustion waste on metal content of crops and soil

    Energy Technology Data Exchange (ETDEWEB)

    Mays, D.A.; Giordano, P.M.; Behel, A.D. Jr. (Tennessee Valley Authority, Muscle Shoals, AL (USA). Agricultural Research Dept.)

    1991-08-01

    The fluidized bed combustion process for removing SO{sub 2} from coal-fired power plant stack gases results in generation of large tonnages of waste requiring environmentally acceptable storage or disposal. A field study was initiated in fall 1985 to determine limits of fluidized bed combustion wasted (FBCW) applications to agronomic crops without causing significant yield reduction or accumulation of heavy metals in plants or the soil. Rates of FBCW ranging from 22 to 560 t ha{sup -1} were incorporated in soil by plowing down single and split applications. Conventional agricultural lime treatments were included for comparison. Tall fescue ({ital Festuca arundinacea}), alfalfa ({ital Medicago sativa L.}), corn ({ital Zea mays L.}), and soybeans ({ital Glycine max. L.}) were grown from 1986-88. Annual applications of 22 t ha{sup -1} did not affect yield or metal uptake of any test crop. A single 112 t ha{sup -1} application had no adverse effect, but repeated applications of that rate lowered corn and soybean yields. The rate of 560 t ha{sup -1} resulted in depressed or eliminated growth of all crops. A high pH and high concentrations of Ca and S were associated with this rate but heavy metals and B concentrations in soil and plant tissue were not significantly affected. 7 refs., 12 tabs.

  5. Wear Behavior of Aluminium Metal Matrix Composite Prepared from Industrial Waste

    Directory of Open Access Journals (Sweden)

    L. Francis Xavier

    2016-01-01

    Full Text Available With an increase in the population and industrialization, a lot of valuable natural resources are depleted to prepare and manufacture products. However industrialization on the other hand has waste disposal issues, causing dust and environmental pollution. In this work, Aluminium Metal Matrix Composite is prepared by reinforcing 10 wt% and 20 wt% of wet grinder stone dust particles an industrial waste obtained during processing of quarry rocks which are available in nature. In the composite materials design wear is a very important criterion requiring consideration which ensures the materials reliability in applications where they come in contact with the environment and other surfaces. Dry sliding wear test was carried out using pin-on-disc apparatus on the prepared composites. The results reveal that increasing the reinforcement content from 10 wt% to 20 wt% increases the resistance to wear rate.

  6. Wear Behavior of Aluminium Metal Matrix Composite Prepared from Industrial Waste.

    Science.gov (United States)

    Xavier, L Francis; Suresh, Paramasivam

    2016-01-01

    With an increase in the population and industrialization, a lot of valuable natural resources are depleted to prepare and manufacture products. However industrialization on the other hand has waste disposal issues, causing dust and environmental pollution. In this work, Aluminium Metal Matrix Composite is prepared by reinforcing 10 wt% and 20 wt% of wet grinder stone dust particles an industrial waste obtained during processing of quarry rocks which are available in nature. In the composite materials design wear is a very important criterion requiring consideration which ensures the materials reliability in applications where they come in contact with the environment and other surfaces. Dry sliding wear test was carried out using pin-on-disc apparatus on the prepared composites. The results reveal that increasing the reinforcement content from 10 wt% to 20 wt% increases the resistance to wear rate.

  7. Isolation of Metals from Liquid Wastes: Reactive Scavenging in Turbulent Thermal Reactors

    Energy Technology Data Exchange (ETDEWEB)

    Jost O.L. Wendt; Alan R. Kerstein; Alexander Scheeline; Arne Pearlstein; William Linak

    2003-08-06

    The Overall project demonstrated that toxic metals (cesium Cs and strontium Sr) in aqueous and organic wastes can be isolated from the environment through reaction with kaolinite based sorbent substrates in high temperature reactor environments. In addition, a state-of-the art laser diagnostic tool to measure droplet characteristic in practical 'dirty' laboratory environments was developed, and was featured on the cover of a recent edition of the scientific journal ''applied Spectroscopy''. Furthermore, great strides have been made in developing a theoretical model that has the potential to allow prediction of the position and life history of every particle of waste in a high temperature, turbulent flow field, a very challenging problem involving as it does, the fundamentals of two phase turbulence and of particle drag physics.

  8. Determination of Different Metals in Steel Waste Samples Using laser Induced Breakdown Spectroscopy

    Directory of Open Access Journals (Sweden)

    A. H. Bakry

    2007-12-01

    Full Text Available Elemental analysis of waste samples collected from steel products manufacturing plant (SPS located at industrial city of Jeddah, Saudi-Arabia has been carried out using Laser Induced Breakdown Spectroscopy (LIBS. The 1064 nm laser radiations from a Nd:YAG laser at an irradiance of 7.6  1010 W cm –2 were used. Atomic emission spectra of the elements present in the waste samples were recorded in the 200 – 620 nm region. Elements such as Fe, W, Ti, Al, Mg, Ca, S, Mn, and Na were detected in these samples. Quantitative determination of the elemental concentration was obtained for these metals against certified standard samples. Parametric dependences of LIBS signal intensity on incident laser energy and time delay between the laser pulse and data acquisition system were also carried out.

  9. Detection of toxic metals in waste water from dairy products plant using laser induced breakdown spectroscopy.

    Science.gov (United States)

    Hussain, T; Gondal, M A

    2008-06-01

    Laser Induced Breakdown Spectroscopy (LIBS) System was developed locally for determination of toxic metals in liquid samples and the system was tested for analysis of waste water collected from dairy products processing plant. The plasma was generated by focusing a pulsed Nd: YAG laser at 1064 nm on waste water samples. Optimal experimental conditions were evaluated for improving the sensitivity of our LIBS system through parametric dependence investigations. The Laser-Induced Breakdown Spectroscopy (LIBS) results were then compared with the results obtained using standard analytical technique such as Inductively Coupled Plasma Emission Spectroscopy (ICP). The evaluation of the potential and capabilities of LIBS as a rapid tool for liquid sample analysis are discussed in brief.

  10. Function of all-metal separators for waste fuels. Phase 1; Funktion av allmetallseparatorer foer avfallsbraenslen. Etapp 1

    Energy Technology Data Exchange (ETDEWEB)

    Jacoby, Juergen; Wrangensten, Lars

    2004-08-01

    Various waste incineration facilities, which use different types of waste fuels, have difficulties with a high content of non-magnetic metal, especially aluminum in their fuels. Aluminum may melt on the grate and can lead to corrosion or fouling in the furnace. Additionally, a high content of aluminum in the flyash may cause difficulties in terms of storage or further use of the ash as e.g. construction material. The industrial demand for efficient separators for non-magnetic metals from a fuel stream is rather large. There is however some uncertainty in the performance and efficiency of metal separators. Two types of separators can be found, the first type is called eddy current separator, the other type is based upon a metal detector with a sorting unit in the form of a chute or similar afterwards. An eddy current separator consists of a fast rotating drum containing several permanent magnets with alternating polarity. Due to the rotation, the change in the magnetic field induces eddy currents in conducting materials. The eddy currents cause a force in non-magnetic metal, the Lorentz force, which repels the material away from the rotating drum while all other material follows the systems flow direction. Systems equipped with a metal detector activate a mechanical sorting device, separate chute or air nozzles, when a metal particle is detected. In contrast to eddy current separators all types of metals can be detected and sorted out by systems based on metal detector. Several technical solutions for metal separation supplied by various manufacturers are described in the report. The companies have been asked to supply product information on the working principle, technical data, efficiency and limits for different types of metals. Two reference power plants have been visited and their experiences with all-metal separators are described. Haendeloeverket in Norrkoeping uses eddy current separators for separation of non-magnetic metals from household waste

  11. Valorization of titanium metal wastes as tanning agent used in leather industry.

    Science.gov (United States)

    Crudu, Marian; Deselnicu, Viorica; Deselnicu, Dana Corina; Albu, Luminita

    2014-10-01

    The development of new tanning agents and new technologies in the leather sector is required to cope with the increasingly higher environmental pressure on the current tanning materials and processes such as tanning with chromium salts. In this paper, the use of titanium wastes (cuttings) resulting from the process of obtaining highly pure titanium (ingots), for the synthesis of new tanning agent and tanning bovine hides with new tanning agent, as alternative to tanning with chromium salts are investigated. For this purpose, Ti waste and Ti-based tanning agent were characterized for metal content by inductively coupled plasma mass spectrometry (ICP-MS) and chemical analysis; the tanned leather (wet white leather) was characterized by Scanning Electron Microscope/Energy Dispersive Using X-ray (Analysis). SEM/EDX analysis for metal content; Differential scanning calorimetric (DSC), Micro-Hot-Table and standard shrinkage temperature showing a hydrothermal stability (ranged from 75.3 to 77°C) and chemical analysis showing the leather is tanned and can be processed through the subsequent mechanical operations (splitting, shaving). On the other hand, an analysis of major minor trace substances from Ti-end waste (especially vanadium content) in new tanning agent and wet white leather (not detected) and residue stream was performed and showed that leachability of vanadium is acceptable. The results obtained show that new tanning agent obtained from Ti end waste can be used for tanning bovine hides, as eco-friendly alternative for chrome tanning. Copyright © 2014 Elsevier Ltd. All rights reserved.

  12. Recovery of metals from waste printed circuit boards by supercritical water pre-treatment combined with acid leaching process.

    Science.gov (United States)

    Xiu, Fu-Rong; Qi, Yingying; Zhang, Fu-Shen

    2013-05-01

    Waste printed circuit boards (PCBs) contain a large number of metals such as Cu, Sn, Pb, Cd, Cr, Zn, and Mn. In this work, an efficient and environmentally friendly process for metals recovery from waste PCBs by supercritical water (SCW) pre-treatment combined with acid leaching was developed. In the proposed process, waste PCBs were pre-treated by SCW, then the separated solid phase product with concentrated metals was subjected to an acid leaching process for metals recovery. The effect of SCW pre-treatment on the recovery of different metals from waste PCBs was investigated. Two methods of SCW pre-treatment were studied: supercritical water oxidation (SCWO) and supercritical water depolymerization (SCWD). Experimental results indicated that SCWO and SCWD pre-treatment had significant effect on the recovery of different metals. SCWO pre-treatment was highly efficient for enhancing the recovery of Cu and Pb, and the recovery efficiency increased significantly with increasing pre-treatment temperature. The recovery efficiency of Cu and Pb for SCWO pre-treatment at 420°C was 99.8% and 80%, respectively, whereas most of the Sn and Cr were immobilized in the residue. The recovery of all studied metals was enhanced by SCWD pre-treatment and increased along with pre-treatment temperature. Up to 90% of Sn, Zn, Cr, Cd, and Mn could be recovered for SCWD pre-treatment at 440°C. Copyright © 2013 Elsevier Ltd. All rights reserved.

  13. Silage supports sulfate reduction in the treatment of metals- and sulfate-containing waste waters.

    Science.gov (United States)

    Wakeman, Kathryn D; Erving, Leena; Riekkola-Vanhanen, Marja L; Puhakka, Jaakko A

    2010-09-01

    Silage was used as source of carbon and electrons for enrichment of silage-degrading and sulfate reducing bacteria (SRB) from boreal, acidic, metals-containing peat-bog samples and to support their use in batch and semi-batch systems in treatment of synthetic waste water. Sulfidogenic silage utilization resulted in a rapid decrease in lactate concentrations; concentrations of acetate, butyrate and propionate increased concomitantly. Synthetic waste water consisting of Mn, Mg and Fe (II) ions inhibited sulfate reduction at concentrations of 6 g/l, 8 g/l and 1 g/l respectively. During treatment, Mn and Mg ions remained in solution while Fe ions partially precipitated. Up to 87 mg sulfate was reduced per gram of silage. Sulfate reduction rates of 34, 22 and 6 mg/l/day were obtained at temperatures of 30, 20 and 9 °C respectively. In semi-batch reactors operated at low pH, the iron precipitation capacity was controlled by sulfate reduction rates and by partial loss of hydrogen sulfide to the gas phase. Passive reactor systems should, therefore, be operated at neutral pH. Metals tolerant, silage-fermenting (predominantly species belonging to genus Clostridium) and sulfate reducing bacteria (including a species similar to the psychrotolerant Desulfovibrio arcticus) were obtained from the peat bog samples. This work demonstrates that silage supports sulfate reduction and can be used as a low cost carbon and electron source for SRB in treatment of metals-containing waste water. Copyright © 2010 Elsevier Ltd. All rights reserved.

  14. Recovering metals from sewage sludge, waste incineration residues and similar substances with hyperaccumulative plants

    Science.gov (United States)

    Kisser, Johannes; Gattringer, Heinz; Iordanopoulos-Kisser, Monika

    2015-04-01

    Sewage sludges as well as ashes from waste incineration plants are known accumulation sinks of many elements that are either important nutrients for biological organisms (phosphorus, potassium, magnesium, etc.) or valuable metals when considered on their own in pure form (nickel, chrome, zinc, etc.); they are also serious pollutants when they occur in wild mixtures at localized anthropogenic end- of-stream points. Austria and many other countries have to import up to 90% of the material inputs of metals from abroad. These primary resources are becoming more expensive as they become more scarce and remaining deposits more difficult to mine, which is a serious concern for industrialized nations. Basic economic and strategic reasoning demands an increase in recycling activities and waste minimization. Technologies to recover metals in a reasonable and economically relevant manner from very diffuse sources are practically non-existent or require large amounts of energy and chemicals, which pose environmental risks. On the other hand agriculture uses large volumes of mineral fertilizers, which are often sourced from mines as well, and thus are also subject to the same principle of finiteness and potential shortage in supply. These converted biological nutrients are taken up by crops and through the food chain and human consumption end up in sewage systems and in wastewater treatment plants in great quantities. The metabolized nutrients mostly do not return to agriculture, but due to contamination with heavy metals are diverted to be used as construction aggregates or are thermally treated and end up rather uselessly in landfills. The project BIO-ORE aimed to explore new pathways to concentrate metals from diluted sources such as sewage sludge and wastewater by using highly efficient biological absorption and transport mechanisms. These enzymatic systems from plants work with very little energy input. The process is called bioaccumulation and can be most effectively

  15. Dysprosium(III) hydroxide coprecipitation system for the separation and preconcentration of heavy metal contents of table salts and natural waters

    Energy Technology Data Exchange (ETDEWEB)

    Peker, Dondu Serpil Kacar [Erciyes University, Faculty of Art and Science, Department of Chemistry, 38039 Kayseri (Turkey); Turkoglu, Orhan [Erciyes University, Faculty of Art and Science, Department of Chemistry, 38039 Kayseri (Turkey); Soylak, Mustafa [Erciyes University, Faculty of Art and Science, Department of Chemistry, 38039 Kayseri (Turkey)]. E-mail: soylak@erciyes.edu.tr

    2007-05-08

    A procedure for the determination of trace amounts of Pb(II), Cu(II), Ni(II), Co(II), Cd(II) and Mn(II) is described, that combines atomic absorption spectrometry-dysprosium hydroxide coprecipitation. The influences of analytical parameters including amount of dysprosium(III), centrifugation time, sample volume, etc. were investigated on the recoveries of analyte ions. The effects of concomitant ions were also examined. The recoveries of the analyte ions were in the range of 95.00-104.00%. The detection limits corresponding to three times the standard deviation of the blank for the analytes were in the range of 14.1-25.3 {mu}g/L. The method was applied to the determination of lead, copper, nickel, cobalt, cadmium and manganese ions in natural waters and table salts good results were obtained (relative standard deviations <10%, recoveries >95%)

  16. Determination of ultratrace levels of dissolved metals in seawater by reaction cell inductively coupled plasma mass spectrometry after ammonia induced magnesium hydroxide coprecipitation.

    Science.gov (United States)

    Ardini, Francisco; Magi, Emanuele; Grotti, Marco

    2011-11-07

    A method for the determination of ultratrace amounts of Cr, Fe, Mn, Pb and Zn in seawater has been developed. It combined the low-blank magnesium hydroxide coprecipitation procedure with quadrupole inductively coupled plasma mass spectrometry and used the dynamic reaction cell technique to resolve the polyatomic interferences arising from the residual matrix, the solvent and plasma gases. Detection limits (3σ(B), n=10) for Cr, Fe, Mn, Pb and Zn were 0.02, 0.10, 0.01, 0.002 and 0.19 nM, respectively, using 50 mL of seawater sample. The accuracy of the analytical procedure was verified by the analysis of the seawater reference materials CASS-4, NASS-5, SAFe D2 and SAFe S. The analytical precision ranged from 3% to 16% (n=6), with a sample throughput of about 6 samples h(-1). Copyright © 2011 Elsevier B.V. All rights reserved.

  17. Studies on the dominant-lethal and fertility effects of the heavy metal compounds methylmercuric hydroxide, mercuric chloride, and cadmium chloride in male and female mice.

    Science.gov (United States)

    Suter, K E

    1975-12-01

    Dominant-lethal effects of 10 mg/kg methylmercuric hydroxide were studied in male mice from two hybrid stocks and in females from one of these stocks. Two other compounds, mercuric chloride (2 mg/kg) and cadmium chloride (2 mg/kh), were studied only in females for dominant-lethal (in one hybrid stock) and reproductive capacity effects (in two hybrid and one mixed stocks). All compounds were administered in a single intraperitoneal injection. When males of one of the two stocks studied were treated with methylmercuric hydroxide, the females to which they were mated exhibited a slight reduction in the total number of implantations and in the number of living embryos. These reductions were accompanied by a very small increase in the incidence of dead implantations. In females, cadmium chloride had no detectable dominant-lethal or other fertility effects, except superovulation. On the other hand, the two mercury compounds slightly reduced the numbers of implants and living embryos in females subjected to dominant-lethal studies. The two mercury compounds also induced a slight reduction in that long-term reproductive performance of one stock of females. These results and those reported earlier by others, indicate that the mercury compounds studied so far are not potent inducers of dominant-lethal mutations in male and female mice. It is not clear whether the small effects on male or female fertility induced in some cases, particularly the increase in dead implantations and reductions in the number of living embryos, were attributable to dominant-lethal mutations or to nongenetic causes.

  18. Greener approach for the extraction of copper metal from electronic waste.

    Science.gov (United States)

    Jadhao, Prashant; Chauhan, Garima; Pant, K K; Nigam, K D P

    2016-11-01

    Technology innovations resulted into a major move from agricultural to industrial economy in last few decades. Consequently, generation of waste electronic and electrical equipments (WEEE) has been increased at a significant rate. WEEE contain large amount of precious and heavy metals and therefore, can be considered a potential secondary resource to overcome the scarcity of metals. Also, presence of these metals may affect the ecosystem due to lack of adequate management of WEEE. Building upon our previous experimental investigations for metal extraction from spent catalyst, present study explores the concept of green technology for WEEE management. Efforts have been made to recover base metal from a printed circuit board using eco-friendly chelation technology and results were compared with the conventional acid leaching method. 83.8% recovery of copper metal was achieved using chelation technology whereas only 27% could be recovered using acid leaching method in absence of any oxidant at optimum reaction conditions. Various characterization studies (energy dispersive X-ray analysis, scanning electron microscopy, X-ray diffraction, inductive coupled plasma spectrophotometry) of Printed Circuit Board (PCB) and residues were performed for qualitative and quantitative analysis of samples. Significant metal extraction, more than 96% recovery of chelating agent, recycling of reactant in next chelation cycle and nearly zero discharge to the environment are the major advantages of the proposed green process which articulate the transcendency of chelation technology over other conventional approaches. Kinetic investigation suggests diffusion controlled process as the rate determining step for the chelate assisted recovery of copper from WEEE with activation energy of 22kJ/mol. Copyright © 2015 Elsevier Ltd. All rights reserved.

  19. Treatment of metal-laden hazardous wastes with advanced Clean Coal Technology by-products

    Energy Technology Data Exchange (ETDEWEB)

    James T. Cobb, Jr.; Ronald D. Neufeld; Jana Agostini; Wiles Elder

    1999-04-05

    This eleventh quarterly report describes work done during the eleventh three-month period of the University of Pittsburgh's project on the ``Treatment of Metal-Laden Hazardous Wastes with Advanced Clean Coal Technology By-Products.'' This report describes the activities of the project team during the reporting period. The principal work has focused upon new laboratory evaluation of samples from Phase 1, discussions with MAX Environmental Technologies, Inc., on the field work of Phase 2, preparing and giving presentations, and making and responding to two outside contacts.

  20. The symbiotic relationship between waste burning and safety in liquid metal reactors

    Energy Technology Data Exchange (ETDEWEB)

    Nelson, J.V.; Dobbin, K.D.; Kessler, S.F.; Wootan, D.W.; Omberg, R.P.; Waltar, A.E.

    1993-06-01

    The relationship between the transmutation of minor actinides and fission products, and safety related reactivity feedbacks in liquid metal reactors (LMR) was explored. Several design features appear promising for performing waste transmutation while retaining the desirable safety characteristics. Innovative variations of conventional LMR configurations and compositions establish symbiotic relationships between plutonium fuel, minor actinides, and fission products. These relationships enhance safety characteristics of the core and provide acceptable fuel and burnup performance. Although a specific design has not been developed, an LMR capable of transmuting the minor actinides and fission products from up to 10 comparable light water reactors while retaining desirable safety features, appears to be feasible.

  1. Treatment of metal-laden hazardous wastes with advanced Clean Coal Technology by-products

    Energy Technology Data Exchange (ETDEWEB)

    James T. Cobb, Jr.; Ronald D. Neufeld; Jana Agostini

    1999-04-12

    This twelfth quarterly report describes work done during the twelfth three-month period of the University of Pittsburgh's project on the ``Treatment of Metal-Laden Hazardous Wastes with Advanced Clean Coal Technology By-Products.'' This report describes the activities of the project team during the reporting period. The principal work has focused upon new laboratory evaluation of samples from Phase 1, discussions with MAX Environmental Technologies, Inc., on the field work of Phase 2, preparing and giving presentations, and making and responding to a number of outside contacts.

  2. TREATMENT OF METAL-LADEN HAZARDOUS WASTES WITH ADVANCED CLEAN COAL TECHNOLOGY BY-PRODUCTS

    Energy Technology Data Exchange (ETDEWEB)

    James T. Cobb, Jr.; Ronald D. Neufeld; Jana Agostini

    1999-06-01

    This sixteenth quarterly report describes work done during the sixteenth three-month period of the University of Pittsburgh's project on the ''Treatment of Metal-Laden Hazardous Wastes with Advanced Clean Coal Technology By-Products.'' This report describes the activities of the project team during the reporting period. The principal work has focused upon new laboratory evaluation of samples from Phase 1, discussions with MAX Environmental Technologies, Inc., on the field work of Phase 2, giving a presentation, and making and responding to several outside contacts.

  3. TREATMENT OF METAL-LADEN HAZARDOUS WASTES WITH ADVANCED CLEAN COAL TECHNOLOGY BY-PRODUCTS

    Energy Technology Data Exchange (ETDEWEB)

    James T. Cobb, Jr.; Ronald D. Neufeld; Jana Agostini

    1999-05-11

    This fifteenth quarterly report describes work done during the fifteenth three-month period of the University of Pittsburgh's project on the ''Treatment of Metal-Laden Hazardous Wastes with Advanced Clean Coal Technology By-Products.'' This report describes the activities of the project team during the reporting period. The principal work has focused upon new laboratory evaluation of samples from Phase 1, discussions with MAX Environmental Technologies, Inc., on the field work of Phase 2, preparing and giving presentations, and making and responding to several outside contacts.

  4. Drop Dynamics and Speciation in Isolation of Metals from Liquid Wastes by Reactive Scavenging

    Energy Technology Data Exchange (ETDEWEB)

    Arne J. Pearlstein; Alexander Scheeline

    2002-08-30

    Computational and experimental studies of the motion and dynamics of liquid drops in gas flows were conducted with relevance to reactive scavenging of metals from atomized liquid waste. Navier-Stoke's computations of deformable drops revealed a range of conditions from which prolate drops are expected, and showed how frajectiones of deformable drops undergoing deceleration can be computed. Experimental work focused on development of emission fluorescence, and scattering diagnostics. The instrument developed was used to image drop shapes, soot, and nonaxisymmetric departures from steady flow in a 22kw combustor

  5. TREATMENT OF METAL-LADEN HAZARDOUS WASTES WITH ADVANCED CLEAN COAL TECHNOLOGY BY-PRODUCTS

    Energy Technology Data Exchange (ETDEWEB)

    James T. Cobb, Jr.; Ronald D. Neufeld; Jana Agostini

    1999-05-10

    This fourteenth quarterly report describes work done during the fourteenth three-month period of the University of Pittsburgh's project on the ''Treatment of Metal-Laden Hazardous Wastes with Advanced Clean Coal Technology By-Products.'' This report describes the activities of the project team during the reporting period. The principal work has focused upon new laboratory evaluation of samples from Phase 1, discussions with MAX Environmental Technologies, Inc., on the field work of Phase 2, preparing presentations, and making and responding to two outside contacts.

  6. Selective extraction and recovery of rare earth metals from phosphor powders in waste fluorescent lamps using an ionic liquid system

    Energy Technology Data Exchange (ETDEWEB)

    Yang, Fan; Kubota, Fukiko; Baba, Yuzo [Department of Applied Chemistry, Graduate School of Engineering, Kyushu University, 744 Motooka, Fukuoka 819-0395 (Japan); Kamiya, Noriho [Department of Applied Chemistry, Graduate School of Engineering, Kyushu University, 744 Motooka, Fukuoka 819-0395 (Japan); Center for Future Chemistry, Kyushu University, 744 Motooka, Fukuoka 819-0395 (Japan); Goto, Masahiro, E-mail: m-goto@mail.cstm.kyushu-u.ac.jp [Department of Applied Chemistry, Graduate School of Engineering, Kyushu University, 744 Motooka, Fukuoka 819-0395 (Japan); Center for Future Chemistry, Kyushu University, 744 Motooka, Fukuoka 819-0395 (Japan)

    2013-06-15

    Highlights: • Recycling of rare earth metals from fluorescent lamps was conducted by ionic liquid-mediated extraction. • Acid leaching from a waste phosphor powder was carried out using sulfuric and nitric acids. • An ionic liquid was used as extracting solvent for the rare earth metals. • Selective extraction of rare earth metals from leach solutions was attained. •The extracting ionic liquid phase was recyclable in the recovery process. -- Abstract: The recycling of rare earth metals from phosphor powders in waste fluorescent lamps by solvent extraction using ionic liquids was studied. Acid leaching of rare earth metals from the waste phosphor powder was examined first. Yttrium (Y) and europium (Eu) dissolved readily in the acid solution; however, the leaching of other rare earth metals required substantial energy input. Ionization of target rare earth metals from the waste phosphor powders into the leach solution was critical for their successful recovery. As a high temperature was required for the complete leaching of all rare earth metals, ionic liquids, for which vapor pressure is negligible, were used as an alternative extracting phase to the conventional organic diluent. An extractant, N, N-dioctyldiglycol amic acid (DODGAA), which was recently developed, showed a high affinity for rare earth metal ions in liquid–liquid extraction although a conventional commercial phosphonic extractant did not. An effective recovery of the rare earth metals, Y, Eu, La and Ce, from the metal impurities, Fe, Al and Zn, was achieved from the acidic leach solution of phosphor powders using an ionic liquid containing DODGAA as novel extractant system.

  7. Synthesis of nanostructured metal–, semiconductor–, and metal/semiconductor–mordenite composites from geothermal waste

    Directory of Open Access Journals (Sweden)

    Oscar E. Jaime-Acuña

    2016-08-01

    Full Text Available Successful synthesis of metal–, semiconductor–, and metal/semiconductor–mordenite nanocomposites, using geothermal solid waste as precursor is reported. Powders of nanostructured composites, consisting of metal and/or semiconductor nanoparticles grown on a mordenite-type zeolitic matrix surface, were synthesized by a one-step solvent-free and organic template-free process. The developed methodology is capable of controlling and tuning the final properties of composites from their synthesis and is also reproducible and repeatable. For comparison and demonstration of the application of the final products, dye photocatalysis degradation tests were done using commercial TiO2 as reference (degradation reached ∼75% in 215 min, k = 0.004 min−1, [M]–S–MOR samples revealed better performance (≥95% in 100 min, k = 0.009 min−1.

  8. Separation and Recovery of Precious Metals from Leach Liquors of Spent Electronic Wastes by Solvent Extraction

    Energy Technology Data Exchange (ETDEWEB)

    Nguyen, Thi Hong; Wang, Lingyun; Lee, Man Seung [Mokpo National University, Mokpo (Korea, Republic of)

    2017-04-15

    Solvent extraction was employed to recover precious metals (Au (III), Pd (II) and Pt (IV)) from the leach solution of spent electronic wastes containing Cu (II), Cr (III) and Fe (III). First, pure Fe (III) and Au (III) were recovered by simultaneous extraction with Cyanex 923 followed by selective stripping with HCl and Na{sub 2}S{sub 2}O{sub 3}. Second, Pt (IV), Pd (II) and Cu (II) were extracted by Alamine 336 from the raffinate. After the removal of Cu (II) by stripping with weak HCl, Pd (II) and Pt (IV) were separately stripped by controlling the concentration of thiourea in the mixture with HCl. A process flow sheet for the separation of precious metals was proposed.

  9. Selective removal/recovery of RCRA metals from waste and process solutions using polymer filtration{trademark} technology

    Energy Technology Data Exchange (ETDEWEB)

    Smith, B.F. [Los Alamos National Lab., NM (United States)

    1997-10-01

    Resource Conservation and Recovery Act (RCRA) metals are found in a number of process and waste streams at many DOE, U.S. Department of Defense, and industrial facilities. RCRA metals consist principally of chromium, mercury, cadmium, lead, and silver. Arsenic and selenium, which form oxyanions, are also considered RCRA elements. Discharge limits for each of these metals are based on toxicity and dictated by state and federal regulations (e.g., drinking water, RCRA, etc.). RCRA metals are used in many current operations, are generated in decontamination and decommissioning (D&D) operations, and are also present in old process wastes that require treatment and stabilization. These metals can exist in solutions, as part of sludges, or as contaminants on soils or solid surfaces, as individual metals or as mixtures with other metals, mixtures with radioactive metals such as actinides (defined as mixed waste), or as mixtures with a variety of inert metals such as calcium and sodium. The authors have successfully completed a preliminary proof-of-principle evaluation of Polymer Filtration{trademark} (PF) technology for the dissolution of metallic mercury and have also shown that they can remove and concentrate RCRA metals from dilute solutions for a variety of aqueous solution types using PF technology. Another application successfully demonstrated is the dilute metal removal of americium and plutonium from process streams. This application was used to remove the total alpha contamination to below 30 pCi/L for the wastewater treatment plant at TA-50 at Los Alamos National Laboratory (LANL) and from nitric acid distillate in the acid recovery process at TA-55, the Plutonium Facility at LANL (ESP-CP TTP AL16C322). This project will develop and optimize the PF technology for specific DOE process streams containing RCRA metals and coordinate it with the needs of the commercial sector to ensure that technology transfer occurs.

  10. Recycling of non-metallic fractions from waste electrical and electronic equipment (WEEE): A review

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Ruixue; Xu, Zhenming, E-mail: zmxu@sjtu.edu.cn

    2014-08-15

    Highlights: • NMFs from WEEE were treated by incineration or land filling in the past. • Environmental risks such as heavy metals and BFRs will be the major problems during the NMFs recycling processes. • Methods and technologies of recycling the two types of NMFs from WEEE, plastics, glasses are reviewed. • More environmental impact assessment should be carried out to evaluate the environmental risks of the recycling products. - Abstract: The world’s waste electrical and electronic equipment (WEEE) consumption has increased incredibly in recent decades, which have drawn much attention from the public. However, the major economic driving force for recycling of WEEE is the value of the metallic fractions (MFs). The non-metallic fractions (NMFs), which take up a large proportion of E-wastes, were treated by incineration or landfill in the past. NMFs from WEEE contain heavy metals, brominated flame retardant (BFRs) and other toxic and hazardous substances. Combustion as well as landfill may cause serious environmental problems. Therefore, research on resource reutilization and safe disposal of the NMFs from WEEE has a great significance from the viewpoint of environmental protection. Among the enormous variety of NMFs from WEEE, some of them are quite easy to recycle while others are difficult, such as plastics, glass and NMFs from waste printed circuit boards (WPCBs). In this paper, we mainly focus on the intractable NMFs from WEEE. Methods and technologies of recycling the two types of NMFs from WEEE, plastics, glass are reviewed in this paper. For WEEE plastics, the pyrolysis technology has the lowest energy consumption and the pyrolysis oil could be obtained, but the containing of BFRs makes the pyrolysis recycling process problematic. Supercritical fluids (SCF) and gasification technology have a potentially smaller environmental impact than pyrolysis process, but the energy consumption is higher. With regard to WEEE glass, lead removing is requisite

  11. New technology for recovering residual metals from nonmetallic fractions of waste printed circuit boards.

    Science.gov (United States)

    Zhang, Guangwen; He, Yaqun; Wang, Haifeng; Zhang, Tao; Wang, Shuai; Yang, Xing; Xia, Wencheng

    2017-06-01

    Recycling of waste printed circuit boards is important for environmental protection and sustainable resource utilization. Corona electrostatic separation has been widely used to recycle metals from waste printed circuit boards, but it has poor separation efficiency for finer sized fractions. In this study, a new process of vibrated gas-solid fluidized bed was used to recycle residual metals from nonmetallic fractions, which were treated using the corona electrostatic separation technology. The effects of three main parameters, i.e., vibration frequency, superficial air flow velocity, and fluidizing time on gravity segregation, were investigated using a vibrating gas-solid fluidized bed. Each size fraction had its own optimum parameters. Corresponding to their optimal segregation performance, the products from each experiment were analyzed using an X-ray fluorescence (XRF) and a scanning electron microscope (SEM) equipped with an energy dispersive spectrometer (EDS). From the results, it can be seen that the metal recoveries of -1+0.5mm, -0.5+0.25mm, and -0.25mm size fractions were 86.39%, 82.22% and 76.63%, respectively. After separation, each metal content in the -1+0.5 or -0.5+0.25mm size fraction reduced to 1% or less, while the Fe and Cu contents are up to 2.57% and 1.50%, respectively, in the -0.25mm size fraction. Images of the nonmetallic fractions with a size of -0.25mm indicated that a considerable amount of clavate glass fibers existed in these nonmetallic fractions, which may explain why fine particles had the poorest segregation performance. Copyright © 2017 Elsevier Ltd. All rights reserved.

  12. Biosorption of heavy metals in polluted water, using different waste fruit cortex

    Science.gov (United States)

    Kelly-Vargas, Kevin; Cerro-Lopez, Monica; Reyna-Tellez, Silvia; Bandala, Erick R.; Sanchez-Salas, Jose Luis

    The biosorption capacity of different cortex fruit wastes including banana (Musa paradisiaca), lemon (Citrus limonum) and orange (Citrus sinensis) peel were evaluated. In order to perform these experiments, grinded dried cortexes were used as package in 100 mm high, 10 mm i.d. columns. The grinded material was powdered in a mortar and passed through a screen in order to get two different particle sizes, 2 and 1 mm, for all powders. To estimate the biosorption capabilities of the tested materials, different heavy metals were passed through the columns and the elution filtrate reloaded different times to increase the retention of metals. The heavy metals used were prepared as synthetic samples at 10 mg/L of Pb(NO3)2, Cd(NO3)2, and Cu(NO3)2·6H2O using primary standards. In preliminary experiments using banana cortex, it was found that material with 1 mm of particle size showed higher retention capability (up to12%) than the material with 2 mm of particle size. Considering these results, 1 mm particle size material was used in further experiments with the other waste materials. It was found that for Pb and Cu removal, lemon and orange cortex showed better biosorption capability when compared with banana cortex (up to 15% less for Pb and 48% less for Cu). For Cd, banana cortex showed better biosorption capability 57% (67.2 mg/g of cortex) more than orange (28.8 mg/g of cortex), and 82% more than lemon (12 mg/g of cortex). Reload of the columns with the filtrate after passing through the column improved the removal capability of all the materials tested from 10% to 50% depending on the cortex and metal tested.

  13. Pollutant emissions during pyrolysis and combustion of waste printed circuit boards, before and after metal removal

    Energy Technology Data Exchange (ETDEWEB)

    Ortuño, Nuria; Conesa, Juan A., E-mail: ja.conesa@ua.es; Moltó, Julia; Font, Rafael

    2014-11-15

    The constant increase in the production of electronic devices implies the need for an appropriate management of a growing number of waste electrical and electronic equipment. Thermal treatments represent an interesting alternative to recycle this kind of waste, but particular attention has to be paid to the potential emissions of toxic by-products. In this study, the emissions from thermal degradation of printed circuit boards (with and without metals) have been studied using a laboratory scale reactor, under oxidizing and inert atmosphere at 600 and 850 °C. Apart from carbon oxides, HBr was the main decomposition product, followed by high amounts of methane, ethylene, propylene, phenol and benzene. The maximum formation of PAHs was found in pyrolysis at 850 °C, naphthalene being the most abundant. High levels of 2-, 4-, 2,4-, 2,6- and 2,4,6-bromophenols were found, especially at 600 °C. Emissions of PCDD/Fs and dioxin-like PCBs were quite low and much lower than that of PBDD/Fs, due to the higher bromine content of the samples. Combustion at 600 °C was the run with the highest PBDD/F formation: the total content of eleven 2,3,7,8-substituted congeners (tetra- through heptaBDD/Fs) was 7240 and 3250 ng WHO{sub 2005}-TEQ/kg sample, corresponding to the sample with and without metals, respectively. - Highlights: • Thermal decomposition of printed circuit boards (with and without metals) is studied. • Important differences were found at the different experimental conditions. • Emission of brominated pollutants is much higher than that of chlorinated. • Metal enhances emission of halogenated compounds. • An increase in the temperature produces the destruction of pollutants.

  14. Selective extraction and recovery of rare earth metals from phosphor powders in waste fluorescent lamps using an ionic liquid system.

    Science.gov (United States)

    Yang, Fan; Kubota, Fukiko; Baba, Yuzo; Kamiya, Noriho; Goto, Masahiro

    2013-06-15

    The recycling of rare earth metals from phosphor powders in waste fluorescent lamps by solvent extraction using ionic liquids was studied. Acid leaching of rare earth metals from the waste phosphor powder was examined first. Yttrium (Y) and europium (Eu) dissolved readily in the acid solution; however, the leaching of other rare earth metals required substantial energy input. Ionization of target rare earth metals from the waste phosphor powders into the leach solution was critical for their successful recovery. As a high temperature was required for the complete leaching of all rare earth metals, ionic liquids, for which vapor pressure is negligible, were used as an alternative extracting phase to the conventional organic diluent. An extractant, N, N-dioctyldiglycol amic acid (DODGAA), which was recently developed, showed a high affinity for rare earth metal ions in liquid-liquid extraction although a conventional commercial phosphonic extractant did not. An effective recovery of the rare earth metals, Y, Eu, La and Ce, from the metal impurities, Fe, Al and Zn, was achieved from the acidic leach solution of phosphor powders using an ionic liquid containing DODGAA as novel extractant system. Copyright © 2013 Elsevier B.V. All rights reserved.

  15. Environmental assessment and management of metal-rich wastes generated in acid mine drainage passive remediation systems.

    Science.gov (United States)

    Macías, Francisco; Caraballo, Manuel A; Nieto, José Miguel

    2012-08-30

    As acid mine drainage (AMD) remediation is increasingly faced by governments and mining industries worldwide, the generation of metal-rich solid residues from the treatments plants is concomitantly raising. A proper environmental management of these metal-rich wastes requires a detailed characterization of the metal mobility as well as an assessment of this new residues stability. The European standard leaching test EN 12457-2, the US EPA TCLP test and the BCR sequential extraction procedure were selected to address the environmental assessment of dispersed alkaline substrate (DAS) residues generated in AMD passive treatment systems. Significant discrepancies were observed in the hazardousness classification of the residues according to the TCLP or EN 12457-2 test. Furthermore, the absence of some important metals (like Fe or Al) in the regulatory limits employed in both leaching tests severely restricts their applicability for metal-rich wastes. The results obtained in the BCR sequential extraction suggest an important influence of the landfill environmental conditions on the metals released from the wastes. To ensure a complete stability of the pollutants in the studied DAS-wastes the contact with water or any other leaching solutions must be avoided and a dry environment needs to be provided in the landfill disposal selected. Copyright © 2012 Elsevier B.V. All rights reserved.

  16. [Release amount of heavy metals in cement product from co-processing waste in cement kiln].

    Science.gov (United States)

    Yang, Yu-Fei; Huang, Qi-Fei; Zhang, Xia; Yang, Yu; Wang, Qi

    2009-05-15

    Clinker was produced by Simulating cement calcination test, and concrete samples were also prepared according to national standard GB/T 17671-1999. Long-term cumulative release amount of heavy metals in cement product from co-processing waste in cement kiln was researched through leaching test which refers to EA NEN 7371 and EA NEN 7375, and one-dimensional diffusion model which is on the base of Fick diffusion law. The results show that availabilities of heavy metals are lower than the total amounts in concrete. The diffusion coefficients of heavy metals are different (Cr > As > Ni > Cd). During 30 years service, the cumulative release amounts of Cr, As, Ni and Cd are 4.43 mg/kg, 0.46 mg/kg, 1.50 mg/kg and 0.02 mg/kg, respectively, and the ratios of release which is the division of cumulative release amount and availability are 27.0%, 18.0%, 3.0% and 0.2%, respectively. The most important influence factor of cumulative release amount of heavy metal is the diffusion coefficient, and it is correlative to cumulative release amount. The diffusion coefficient of Cr and As should be controlled exactly in the processing of input the cement-kiln.

  17. Laboratory Scale Thermal Plasma Arc Vitrification Studies of Heavy Metal-Laden Waste.

    Science.gov (United States)

    Cortez, R; Zaghloul, H H; Stephenson, L D; Smith, E D; Wood, J W; Cahil, D G

    1996-11-01

    Plasma processing has been identified as a useful tool for immobilizing heavy metal-contaminated wastes into safe, leach-resistant slag. Although much effort has gone into developing this technology on a pilot scale, not much information has been published on basic research topics. A laboratory-scale plasma arc furnace located at the University of Illinois was operated in cooperation with the U.S. Army Construction Engineering Research Laboratories in an effort to establish an understanding of the chemical and physical processes (such as metal volatilization and resultant gas evolution) that occur during thermal plasma treatment of metal-spiked samples. Experiments were conducted on nickel and chromium using a highly instrumented furnace equipped with a 75 kW transferred arc plasma torch. The volatility of nickel and chromium was examined as a function of varying oxygen partial pressures. Oxidizing conditions reduced the total dust gathered for both the nickel and chromium samples, although each dust sample was found to be metal-enriched. Plasma treating increased the leach-resistance of the slags by at least one order of magnitude when compared to unprocessed specimens. The leach- resistance of the nickel-containing slags increased in the presence of oxygen, whereas chromium samples remained relatively constant.

  18. Test plan for immobilization of salt-containing surrogate mixed wastes using polyester resins

    Energy Technology Data Exchange (ETDEWEB)

    Biyani, R.K.; Douglas, J.C.; Hendrickson, D.W.

    1997-07-07

    Past operations at many Department of Energy (DOE) sites have resulted in the generation of several waste streams with high salt content. These wastes contain listed and characteristic hazardous constituents and are radioactive. The salts contained in the wastes are primarily chloride, sulfate, nitrate, metal oxides, and hydroxides. DOE has placed these types of wastes under the purview of the Mixed Waste Focus Area (MWFA). The MWFA has been tasked with developing and facilitating the implementation of technologies to treat these wastes in support of customer needs and requirements. The MWFA has developed a Technology Development Requirements Document (TDRD), which specifies performance requirements for technology owners and developers to use as a framework in developing effective waste treatment solutions. This project will demonstrate the use of polyester resins in encapsulating and solidifying DOE`s mixed wastes containing salts, as an alternative to conventional and other emerging immobilization technologies.

  19. Recovering metallic fractions from waste electrical and electronic equipment by a novel vibration system

    Energy Technology Data Exchange (ETDEWEB)

    Habib, Muddasar, E-mail: muddasar77@hotmail.com [Department of Chemical Engineering, University of Engineering and Technology, Peshawar (Pakistan); Miles, Nicholas J.; Hall, Philip [Faculty of Science and Engineering, University of Nottingham Ningbo China, Taikang East Road, Ningbo 315100 (China)

    2013-03-15

    Highlights: ► This work focuses on demonstrating a new scaled up technology to separate the metallic and non-metallic fractions of PCBs. ► PCBs comminuted to <1 mm in size resulted in metallic grade concentration of 95% in some of the recovered products. ► Good separation was observed at 40 mm particle bed height due to the formation of well-structured global convection currents. ► The work reported here contributes to the development of a new approach to dry, fine particle separation. - Abstract: The need to recover and recycle valuable resources from Waste Electrical and Electronic Equipment (WEEE) is of growing importance as increasing amounts are generated due to shorter product life cycles, market expansions, new product developments and, higher consumption and production rates. The European Commission (EC) directive, 2002/96/EC, on WEEE became law in UK in January 2007 setting targets to recover up to 80% of all WEEE generated. Printed Wire Board (PWB) and/or Printed Circuit Board (PCB) is an important component of WEEE with an ever increasing tonnage being generated. However, the lack of an accurate estimate for PCB production, future supply and uncertain demands of its recycled materials in international markets has provided the motivation to explore different approaches to recycle PCBs. The work contained in this paper focuses on a novel, dry separation methodology in which vertical vibration is used to separate the metallic and non-metallic fractions of PCBs. When PCBs were comminuted to less than 1 mm in size, metallic grades as high as 95% (measured by heavy liquid analysis) could be achieved in the recovered products.

  20. A dipeptide-based superhydrogel: Removal of toxic dyes and heavy metal ions from waste water.

    Science.gov (United States)

    Nandi, Nibedita; Baral, Abhishek; Basu, Kingshuk; Roy, Subhasish; Banerjee, Arindam

    2017-01-01

    A short peptide-based molecule has been found to form a strong hydrogel at phosphate buffer solution of pH 7.46. The hydrogel has been characterized thoroughly using various techniques including field emission scanning electron microscopy (FE-SEM), wide angle powder X-ray diffraction (PXRD), and rheological analysis. It has been observed from FE-SEM images that entangled nanofiber network is responsible for gelation. Rheological investigation demonstrates that the self-assembly of this synthetic dipeptide results in the formation of mechanically strong hydrogel with storage modulus (G') around 104 Pa. This gel has been used for removing both cationic and anionic toxic organic dyes (Brilliant Blue, Congo red, Malachite Green, Rhodamine B) and metal ions (Co2+ and Ni2+ ) from waste water. Moreover, only a small amount of the gelator is required (less than 1 mg/mL) for preparation of this superhydrogel and even this hydrogel can be reused three times for dye/metal ion absorption. This signifies the importance of the hydrogel towards waste water management. © 2016 Wiley Periodicals, Inc.

  1. Determination of heavy metals and halogens in plastics from electric and electronic waste.

    Science.gov (United States)

    Dimitrakakis, Emmanouil; Janz, Alexander; Bilitewski, Bernd; Gidarakos, Evangelos

    2009-10-01

    The presence of hazardous substances and preparations in small waste electrical and electronic equipment (sWEEE) found in the residual household waste stream of the city of Dresden, Germany has been investigated. The content of sWEEE plastics in heavy metals and halogens is determined using handheld X-ray fluorescence analysis (HXRF), elemental analysis by means of atomic absorption spectrometry (AAS) and ion exchange chromatography (IEC). Mean value of results for heavy metals in samples (n=51) by AAS are 17.4 mg/kg for Pb, 5.7 mg/kg for Cd, 8.4 mg/kg for Cr. The mass fraction of an additive as shown by HXRF (n=161) can vary over a wide range. Precise deductions as regards sWEEE plastics content in hazardous substances and preparations cannot be made. Additional research would be expedient regarding the influence of hazardous substances to recycling processes, in particular regarding the contamination of clean fractions in the exit streams of a WEEE treatment plant. Suitable standards for calibrating HXRF for use on EEE plastics or complex electr(on)ic components do not exist and should be developed.

  2. Pollutant emissions during pyrolysis and combustion of waste printed circuit boards, before and after metal removal.

    Science.gov (United States)

    Ortuño, Nuria; Conesa, Juan A; Moltó, Julia; Font, Rafael

    2014-11-15

    The constant increase in the production of electronic devices implies the need for an appropriate management of a growing number of waste electrical and electronic equipment. Thermal treatments represent an interesting alternative to recycle this kind of waste, but particular attention has to be paid to the potential emissions of toxic by-products. In this study, the emissions from thermal degradation of printed circuit boards (with and without metals) have been studied using a laboratory scale reactor, under oxidizing and inert atmosphere at 600 and 850 °C. Apart from carbon oxides, HBr was the main decomposition product, followed by high amounts of methane, ethylene, propylene, phenol and benzene. The maximum formation of PAHs was found in pyrolysis at 850 °C, naphthalene being the most abundant. High levels of 2-, 4-, 2,4-, 2,6- and 2,4,6-bromophenols were found, especially at 600 °C. Emissions of PCDD/Fs and dioxin-like PCBs were quite low and much lower than that of PBDD/Fs, due to the higher bromine content of the samples. Combustion at 600 °C was the run with the highest PBDD/F formation: the total content of eleven 2,3,7,8-substituted congeners (tetra- through heptaBDD/Fs) was 7240 and 3250 ng WHO2005-TEQ/kg sample, corresponding to the sample with and without metals, respectively. Copyright © 2014 Elsevier B.V. All rights reserved.

  3. Quantitative analysis of metals in waste foundry sands by calibration free-laser induced breakdown spectroscopy

    Science.gov (United States)

    Díaz Pace, D. M.; Miguel, R. E.; Di Rocco, H. O.; Anabitarte García, F.; Pardini, L.; Legnaioli, S.; Lorenzetti, G.; Palleschi, V.

    2017-05-01

    Laser-induced breakdown spectroscopy (LIBS) was applied for quantitative analysis of the elemental composition of waste molding and core sands produced from industry as part of the casting process. To perform the analysis, waste foundry sands (WFS) were collected from metalcasting foundries and prepared in the form of solid pellets with the addition of polyvinyl alcohol as binder. The measurements were carried out using the Mobile double pulse instrument for LIBS analysis (Modì). The spectral analysis was carried out with the calibration-free approach (CF-LIBS). Metal elements commonly found in WFS including Al, Ba, Fe, Li, Mg, Mn, Pb, Ti, Zr, and Zn, were detected and quantified. The metal concentrations for WFS were compared with virgin sand to assess the influence of the casting material as well as the binders used in the foundries to reclaim the sands. The results demonstrated the feasibility of LIBS method as an alternative or complementary technique for the chemical characterization of WFS.

  4. Leaching capacity of metals-metalloids and recovery of valuable materials from waste LCDs.

    Science.gov (United States)

    Savvilotidou, Vasiliki; Hahladakis, John N; Gidarakos, Evangelos

    2015-11-01

    The purpose of Directive 2012/19/EU which is related to WEEE (Waste Electrical and Electronic Equipment), also known as "e-waste", is to contribute to their sustainable production and consumption that would most possibly be achieved by their recovery, recycling and reuse. Under this perspective, the present study focused on the recovery of valuable materials, metals and metalloids from LCDs (Liquid Crystal Displays). Indium (In), arsenic (As) and stibium (Sb) were selected to be examined for their Leaching Capacity (R) from waste LCDs. Indium was selected mainly due to its rarity and preciousness, As due to its high toxicity and wide use in LCDs and Sb due to its recent application as arsenic's replacement to improve the optimal clarity of a LCD screen. The experimental procedure included disassembly of screens along with removal and recovery of polarizers via thermal shock, cutting, pulverization and digestion of the shredded material and finally leaching evaluation of the aforementioned elements. Leaching tests were conducted under various temperatures, using various solid:liquid (S/L) ratios and solvents (acid mixtures), to determine the optimal conditions for obtaining the maximum leaching capacities. The examined elements exhibited different leaching behaviors, mainly due to the considerable diversity in their inherent characteristic properties. Indium demonstrated the highest recovery percentages (approximately 60%), while the recovery of As and Sb was unsuccessful, obtaining poor leaching percentages (0.16% and 0.5%, respectively). Copyright © 2015 Elsevier Ltd. All rights reserved.

  5. Bio-leaching of toxic metals from geothermal waste. A preliminary engineering analysis

    Energy Technology Data Exchange (ETDEWEB)

    Dobryn, D.G.; Brisson, A.L.; Lee, C.M.; Roll, S.M.

    1986-02-01

    The feasibility of a biological facility to treat geothermal sludge from a base case 50-MW double-flash geothermal power plant in the Imperial Valley, California was evaluated. The effect of sludge and nutrient concentration, agitation air bubbling and sterility on the rate of metal solubilization by the bacteria Thiobacillus thiooxidans and ferrooxidans was examined. All experiments were performed in batch flasks and monitored daily for bacterial growth. T. Thiooxidans leached 36% of the zinc in the sludge after 288 hr but leached little chromium. T. ferrooxidans removed 60% of the chromium in the sludge after 250 hr but did not leach zinc. Sludge to medium ratios of greater than 10% were toxic to the microorganisms studied. the experimental results were used to design a biological solid-waste treatment plant. The design basis used was 5 wt % sludge in the leaching vessel with a residence time of 10 days. The non-regulated waste resulting from the treatment plant could be used for land fill or construction materials. The total capital cost for the bio-leaching plant is $3.3 million with an annual operating cost of $690,000. The total cost of this plant is about 0.2 cents/kWh of electricity produced, which is essentially the same cost as hauling the solid waste to a hazardous disposal site. This cost accounts for about 5% of the cost of producing electricity from geothermal power (4 cent/kWh).

  6. Systems engineering approach for the reuse of metallic waste from NPP decommissioning and dose evaluation

    Energy Technology Data Exchange (ETDEWEB)

    Seo, Hyung Woo; Kim, Chang Lak [KEPCO International Nuclear Graduate School, Ulsan (Korea, Republic of)

    2017-03-15

    The oldest commercial reactor in South Korea, Kori-1 Nuclear Power Plant (NPP), will be shut down in 2017. Proper treatment for decommissioning wastes is one of the key factors to decommission a plant successfully. Particularly important is the recycling of clearance level or very low level radioactively contaminated metallic wastes, which contributes to waste minimization and the reduction of disposal volume. The aim of this study is to introduce a conceptual design of a recycle system and to evaluate the doses incurred through defined work flows. The various architecture diagrams were organized to define operational procedures and tasks. Potential exposure scenarios were selected in accordance with the recycle system, and the doses were evaluated with the RESRAD-RECYCLE computer code. By using this tool, the important scenarios and radionuclides as well as impacts of radionuclide characteristics and partitioning factors are analyzed. Moreover, dose analysis can be used to provide information on the necessary decontamination, radiation protection process, and allowable concentration limits for exposure scenarios.

  7. Industrial symbiosis: high purity recovery of metals from Waelz sintering waste by aqueous SO2 solution.

    Science.gov (United States)

    Copur, Mehmet; Pekdemir, Turgay; Colak, Sabri; Künkül, Asim

    2007-10-22

    Sintering operation in the production of Zn, Cd, and Pb by Waelz process produces a powdery waste containing mainly (about 70%) ZnO, CdO, and PbO. The waste may be referred to as Waelz sintering waste (WSW). The aim of this study is to develop a process for the separation and recovery of the metals from WSW with high purities. The process is based on the dissolution of the WSW in aqueous SO2 solution. The research reported here concentrated on the effect of some important operational parameters on dissolution process. The parameters investigated and their ranges were as follows: SO(2) gas flow rate (V); 38-590 ml/min, stirring speed (W); 100-1000 rpm, reaction temperature (T); 13-60 degrees C, reaction time (t); 1-16 min, and solid-liquid ratio (S/L); 0.1-0.5 g/ml. The results showed that the dissolution rate increased with increasing W, V, and S/L and decreasing T. The best dissolution conditions were found to be V=325 ml/min, W=600 rpm, t=6 min, T=21 degrees C, and S/L=0.1g/ml. Separation of Zn from Cd involved precipitation of ZnSO3 from a mixture solution. The best pH level for the precipitation was observed to be 6.

  8. Pressure-induced decomposition of indium hydroxide.

    Science.gov (United States)

    Gurlo, Aleksander; Dzivenko, Dmytro; Andrade, Miria; Riedel, Ralf; Lauterbach, Stefan; Kleebe, Hans-Joachim

    2010-09-15

    A static pressure-induced decomposition of indium hydroxide into metallic indium that takes place at ambient temperature is reported. The lattice parameter of c-In(OH)(3) decreased upon compression from 7.977(2) to approximately 7.45 A at 34 GPa, corresponding to a decrease in specific volume of approximately 18%. Fitting the second-order Birch-Murnaghan equation of state to the obtained compression data gave a bulk modulus of 99 +/- 3 GPa for c-In(OH)(3). The c-In(OH)(3) crystals with a size of approximately 100 nm are comminuted upon compression, as indicated by the grain-size reduction reflected in broadening of the diffraction reflections and the appearance of smaller (approximately 5 nm) incoherently oriented domains in TEM. The rapid decompression of compressed c-In(OH)(3) leads to partial decomposition of indium hydroxide into metallic indium, mainly as a result of localized stress gradients caused by relaxation of the highly disordered indium sublattice in indium hydroxide. This partial decomposition of indium hydroxide into metallic indium is irreversible, as confirmed by angle-dispersive X-ray diffraction, transmission electron microscopy imaging, Raman scattering, and FTIR spectroscopy. Recovered c-In(OH)(3) samples become completely black and nontransparent and show typical features of metals, i.e., a falling absorption in the 100-250 cm(-1) region accompanied by a featureless spectrum in the 250-2500 cm(-1) region in the Raman spectrum and Drude-like absorption of free electrons in the region of 4000-8000 cm(-1) in the FTIR spectrum. These features were not observed in the initial c-In(OH)(3), which is a typical white wide-band-gap semiconductor.

  9. Determining heavy metals in spent compact fluorescent lamps (CFLs) and their waste management challenges: Some strategies for improving current conditions

    Energy Technology Data Exchange (ETDEWEB)

    Taghipour, Hassan, E-mail: hteir@yahoo.com [Department of Environmental Health Engineering, Tabriz University of Medical Sciences, Tabriz (Iran, Islamic Republic of); Amjad, Zahra [Student Research Committee, Department of Environmental Health Engineering, Tabriz University of Medical Sciences, Tabriz (Iran, Islamic Republic of); Jafarabadi, Mohamad Asghari [Medical Education Research Center, Department of Statistics and Epidemiology, Tabriz University of Medical Sciences, Tabriz (Iran, Islamic Republic of); Gholampour, Akbar [Department of Environmental Health Engineering, Tabriz University of Medical Sciences, Tabriz (Iran, Islamic Republic of); Norouz, Prviz [Environmental Health Engineering, Shahid Beheshti University of Medical Sciences, Tehran (Iran, Islamic Republic of)

    2014-07-15

    Highlights: • Heavy metals in spent compact fluorescent lamps (CFLs) determined. • Current waste management condition of CFLs in Iran assessed. • Currently, waste of CFLs is disposed by municipal waste stream in waste landfills. • We propose extended producer responsibility (EPR) for CFLs waste management. - Abstract: From environmental viewpoint, the most important advantage of compact fluorescent lamps (CFLs) is reduction of green house gas emissions. But their significant disadvantage is disposal of spent lamps because of containing a few milligrams of toxic metals, especially mercury and lead. For a successful implementation of any waste management plan, availability of sufficient and accurate information on quantities and compositions of the generated waste and current management conditions is a fundamental prerequisite. In this study, CFLs were selected among 20 different brands in Iran. Content of heavy metals including mercury, lead, nickel, arsenic and chromium was determined by inductive coupled plasma (ICP). Two cities, Tehran and Tabriz, were selected for assessing the current waste management condition of CFLs. The study found that waste generation amount of CFLs in the country was about 159.80, 183.82 and 153.75 million per year in 2010, 2011 and 2012, respectively. Waste generation rate of CFLs in Iran was determined to be 2.05 per person in 2012. The average amount of mercury, lead, nickel, arsenic and chromium was 0.417, 2.33, 0.064, 0.056 and 0.012 mg per lamp, respectively. Currently, waste of CFLs is disposed by municipal waste stream in waste landfills. For improving the current conditions, we propose by considering the successful experience of extended producer responsibility (EPR) in other electronic waste management. The EPR program with advanced recycling fee (ARF) is implemented for collecting and then recycling CFLs. For encouraging consumers to take the spent CFLs back at the end of the products’ useful life, a proportion of

  10. [Determination of metals in waste bag filter of steel works by microwave digestion-flame atomic absorption spectrometry].

    Science.gov (United States)

    Ning, Xun-An; Zhou, Yun; Liu, Jing-Yong; Wang, Jiang-Hui; Li, Lei; Ma, Xiao-Guo

    2011-09-01

    A method of microwave digestion technique-flame atomic absorption spectrometry was proposed to determine the total contents of Cu, Zn, Pb, Cd, Cr and Ni in five different kinds of waste bag filters from a steel plant. The digestion effects of the six acid systems on the heavy metals digestion were studied for the first time. The relative standard deviation (RSD) of the method was between 1.02% and 9.35%, and the recovery rates obtained by standard addition method ranged from 87.7% to 105.6%. The results indicated that the proposed method exhibited the advantages of simplicity, speediness, accuracy and repeatability, and it was suitable for determining the metal elements of the waste bag filter. The results also showed that different digestion systems should be used according to different waste bag filters. The waste bag filter samples from different production processes had different metal elements content. The Pb and Zn were the highest in the waste bag filters, while the Cu, Ni, Cd and Cr were relatively lower. These determination results provided the scientific data for further treatment and disposal of the waste bag filter.

  11. Structures and heats of formation of simple alkaline earth metal compounds: fluorides, chlorides, oxides, and hydroxides for Be, Mg, and Ca.

    Science.gov (United States)

    Vasiliu, Monica; Feller, David; Gole, James L; Dixon, David A

    2010-09-02

    Geometry parameters, frequencies, heats of formation, and bond dissociation energies are predicted for the simple alkaline earth (Be, Mg and Ca) fluorides, chlorides, oxides, and hydroxides at the coupled cluster theory [CCSD(T)] level including core-valence correlation with the aug-cc-pwCVnZ basis sets up to n = 5 in some cases. Additional corrections (scalar relativistic effects, vibrational zero-point energies, and atomic spin-orbit effects) were necessary to accurately calculate the total atomization energies and heats of formation. The calculated geometry parameters, frequencies, heats of formation, and bond dissociation energies are compared with the available experimental data. For a number of these alkaline earth compounds, the experimental geometries and energies are not reliable. MgF(2) and BeF(2) are predicted to be linear and CaF(2) is predicted to be bent. BeOH is predicted to be bent, whereas MgOH and CaOH are linear. The OBeO angle in Be(OH)(2) is not linear, and the molecule has C(2) symmetry. The heat of formation at 298 K for MgO is calculated to be 32.3 kcal/mol, and the bond dissociation energy at 0 K is predicted to be 61.5 kcal/mol.

  12. Integrated bioleaching of copper metal from waste printed circuit board-a comprehensive review of approaches and challenges.

    Science.gov (United States)

    Awasthi, Abhishek Kumar; Zeng, Xianlai; Li, Jinhui

    2016-11-01

    Waste electrical and electronic equipment (e-waste) is the most rapidly growing waste stream in the world, and the majority of the residues are openly disposed of in developing countries. Waste printed circuit boards (WPCBs) make up the major portion of e-waste, and their informal recycling can cause environmental pollution and health risks. Furthermore, the conventional disposal and recycling techniques-mechanical treatments used to recover valuable metals, including copper-are not sustainable in the long term. Chemical leaching is rapid and efficient but causes secondary pollution. Bioleaching is a promising approach, eco-friendly and economically feasible, but it is slower process. This review considers the recycling potential of microbes and suggests an integrated bioleaching approach for Cu extraction and recovery from WPCBs. The proposed recycling system should be more effective, efficient and both technically and economically feasible.

  13. Preparation of value-added metal-organic frameworks (MOFs) using waste PET bottles as source of acid linker

    CSIR Research Space (South Africa)

    Dyosiba, Xoliswa

    2016-12-01

    Full Text Available of Value-added Metal-organic Frameworks (MOFs) Using Waste PET Bottles as Source of Acid Linker Xoliswa Dyosiba, Jianwei Ren, Nicholas M. Musyoka, Henrietta W. Langmi, Mkhulu Mathe, Maurice S. Onyango PII: S2214-9937(16)30053-7 DOI: doi:10.1016/j..., Hen- rietta W. Langmi, Mkhulu Mathe, Maurice S. Onyango, Preparation of Value-added Metal-organic Frameworks (MOFs) Using Waste PET Bottles as Source of Acid Linker, Sustainable Materials and Technologies (2016), doi:10.1016/j.susmat.2016...

  14. Flow analysis of heavy metals in a pilot-scale incinerator for residues from waste electrical and electronic equipment dismantling

    Energy Technology Data Exchange (ETDEWEB)

    Long, Yu-Yang; Feng, Yi-Jian; Cai, Si-Shi; Ding, Wei-Xu; Shen, Dong-Sheng, E-mail: shends@zju.edu.cn

    2013-10-15

    Highlights: • Cu, Zn, Pb, and Ni are enriched in bottom ash from WEEE dismantling residues. • The heavy metal residual fraction restricts transfer in the incinerator. • Pre-treatment to remove heavy metals from WEEE residues would reduce emissions. -- Abstract: The large amount of residues generated from dismantling waste electrical and electronic equipment (WEEE) results in a considerable environmental burden. We used material flow analysis to investigate heavy metal behavior in an incineration plant in China used exclusively to incinerate residues from WEEE dismantling. The heavy metals tested were enriched in the bottom and fly ashes after incineration. However, the contents of heavy metals in the bottom ash, fly ash and exhaust gas do not have a significant correlation with that of the input waste. The evaporation and recondensation behavior of heavy metals caused their contents to differ with air pollution control equipment because of the temperature difference during gas venting. Among the heavy metals tested, Cd had the strongest tendency to transfer during incineration (T{sub Cd} = 69.5%) because it had the lowest melting point, followed by Cu, Ni, Pb and Zn. The exchangeable and residual fractions of heavy metals increased substantially in the incineration products compared with that of the input residues. Although the mass of residues from WEEE dismantling can be reduced by 70% by incineration, the safe disposal of the metal-enriched bottom and fly ashes is still required.

  15. Mineralogic sources of metals in leachates from the weathering of sedex, massive sulfide, and vein deposit mining wastes

    Science.gov (United States)

    Diehl, S.F.; Hageman, P.L.; Seal, R.R.; Piatak, N.M.; Lowers, H.

    2011-01-01

    Weathered mine waste consists of oxidized primary minerals and chemically unstable secondary phases that can be sources of readily soluble metals and acid rock drainage. Elevated concentrations of metals such as Cd, Cu, Fe, Mn, Ni, Pb, and Zn are observed in deionized water-based leachate solutions derived from complex sedex and Cu-Pb-Zn mine wastes. Leachate (USGS FLT) from the Elizabeth mine, a massive sulfide deposit, has a pH of 3.4 and high concentrations of Al (16700 ug/L), Cu (440 ug/L), and Zn (8620 ug/L). Leachate from the sedex Faro mine has a pH of 3.5 and high concentrations of Al (2040 ug/L), Cu (1930 ug/L), Pb (2080 ug/L), and Zn (52900 ug/L). In contrast, higher-pH leachates produced from tailings of polymetallic vein deposits have order of magnitude lower metal concentrations. These data indicate that highly soluble secondary mineral phases exist at the surface of waste material where the samples were collected. Sulfide minerals from all sites exhibit differential degrees of weathering, from dissolution etched grain rims, to rinds of secondary minerals, to skeletal remnants. These microscale mineral-dissolution textures enhance weathering and metal teachability of waste material. Besides the formation of secondary minerals, sulfide grains from dried tailings samples may be coated by amorphous Fe-Al-Si minerals that also adsorb metals such as Cu, Ni, and Zn.

  16. Chemical associations and mobilization of heavy metals in fly ash from municipal solid waste incineration.

    Science.gov (United States)

    Weibel, Gisela; Eggenberger, Urs; Schlumberger, Stefan; Mäder, Urs K

    2017-04-01

    This study focusses on chemical and mineralogical characterization of fly ash and leached filter cake and on the determination of parameters influencing metal mobilization by leaching. Three different leaching processes of fly ash from municipal solid waste incineration (MSWI) plants in Switzerland comprise neutral, acidic and optimized acidic (+ oxidizing agent) fly ash leaching have been investigated. Fly ash is characterized by refractory particles (Al-foil, unburnt carbon, quartz, feldspar) and newly formed high-temperature phases (glass, gehlenite, wollastonite) surrounded by characteristic dust rims. Metals are carried along with the flue gas (Fe-oxides, brass) and are enriched in mineral aggregates (quartz, feldspar, wollastonite, glass) or vaporized and condensed as chlorides or sulphates. Parameters controlling the mobilization of neutral and acidic fly ash leaching are pH and redox conditions, liquid to solid ratio, extraction time and temperature. Almost no depletion for Zn, Pb, Cu and Cd is achieved by performing neutral leaching. Acidic fly ash leaching results in depletion factors of 40% for Zn, 53% for Cd, 8% for Pb and 6% for Cu. The extraction of Pb and Cu are mainly limited due to a cementation process and the formation of a PbCu 0 -alloy-phase and to a minor degree due to secondary precipitation (PbCl 2 ). The addition of hydrogen peroxide during acidic fly ash leaching (optimized acidic leaching) prevents this reduction through oxidation of metallic components and thus significantly higher depletion factors for Pb (57%), Cu (30%) and Cd (92%) are achieved. The elevated metal depletion using acidic leaching in combination with hydrogen peroxide justifies the extra effort not only by reduced metal loads to the environment but also by reduced deposition costs. Copyright © 2016 Elsevier Ltd. All rights reserved.

  17. Electronic spectra of anions intercalated in layered double hydroxides

    Indian Academy of Sciences (India)

    Transition metal complexes intercalated in layered double hydroxides have a different electronic structure as compared to their free state owing to their confinement within the interlayer gallery. UV–Vis absorptions of the intercalated complex anions show a significant shift as compared to their free state. The ligand to metal ...

  18. Metal content in fruit-bodies and mycorrhizas of Pisolithus arrhizus from zinc wastes in Poland

    Directory of Open Access Journals (Sweden)

    Katarzyna Turnau

    2014-08-01

    Full Text Available Pisolithus arrhizus has been selected for investigation as one of the ectomycorrhizal species most resistant to stress factors. Metal content in fruit-bodies and mycorrhizas was estimated to evaluate their role as bioindicators and to check whether mycorrhizas have any special properties for heavy metal accumulation. Fruit-bodies and mycorrhizas were collected from zinc wastes in Katowice-Wełnowiec and analyzed using conventional atomic absorption spectroscopy and energy dispersive spectroscopy accompanying scanning electron microscopy. Differences in tendencies to accumulate metals within sporophores and mycorrhizas were found. The fruit-bodies accumulated Al (up to 640 µg g-1, while high concentrations of Al, Zn, Fe, Ca and Si were noted in the outer mantle of the mycorrhizas. in the material secreted and in the mycelium wali. The content of elements varied depending on the agę of mycorrhizas. The ability of extramatrical mycelium and hyphae forming mycorrhizal mantle to immobilize potentially toxic elements might indicate biofiltering properties though thc next step should include investigations on ability of the fungus to prevent element uptake by the plant.

  19. Recovering metallic fractions from waste electrical and electronic equipment by a novel vibration system.

    Science.gov (United States)

    Habib, Muddasar; Miles, Nicholas J; Hall, Philip

    2013-03-01

    The need to recover and recycle valuable resources from Waste Electrical and Electronic Equipment (WEEE) is of growing importance as increasing amounts are generated due to shorter product life cycles, market expansions, new product developments and, higher consumption and production rates. The European Commission (EC) directive, 2002/96/EC, on WEEE became law in UK in January 2007 setting targets to recover up to 80% of all WEEE generated. Printed Wire Board (PWB) and/or Printed Circuit Board (PCB) is an important component of WEEE with an ever increasing tonnage being generated. However, the lack of an accurate estimate for PCB production, future supply and uncertain demands of its recycled materials in international markets has provided the motivation to explore different approaches to recycle PCBs. The work contained in this paper focuses on a novel, dry separation methodology in which vertical vibration is used to separate the metallic and non-metallic fractions of PCBs. When PCBs were comminuted to less than 1mm in size, metallic grades as high as 95% (measured by heavy liquid analysis) could be achieved in the recovered products. Copyright © 2012 Elsevier Ltd. All rights reserved.

  20. Distribution of heavy metal pollution in sediments from an acid leaching site of e-waste.

    Science.gov (United States)

    Quan, Sheng-Xiang; Yan, Bo; Lei, Chang; Yang, Fan; Li, Ning; Xiao, Xian-Ming; Fu, Jia-Mo

    2014-11-15

    The spatial distribution, bioavailability, potential risks and emission sources of 12 heavy metals in sediments from an acid leaching site of e-waste were investigated. The results showed that the sediments from the acid leaching site were significantly contaminated with Cu, Zn, Cd, Sn, Sb and Pb, especially in the middle sediments (30-50 cm), with average concentrations of 4820, 1260, 10.7, 2660, 5690 and 2570 mg/kg, respectively. Cu, Cd and Pb were mainly present in the non-residual fractions, suggesting that the sediments from the acid leaching site may exert considerable risks. Mn, Ni, Zn, Sn and Sb were predominantly associated with the residual fraction. Despite their low reactivity and bioavailability, uncommon pollutants, such as Sn and Sb, may exert environmental risks due to their extremely elevated total concentrations. All of these results indicate that there is an urgent need to control the sources of heavy metal emission and to remediate contaminated sediments. In addition to Ni, Cu, Zn, Cd and Pb, the sediments from an acid leaching site in Guiyu were heavily polluted with uncommon heavy metal pollutants, such as Sn and Sb. Copyright © 2014 Elsevier B.V. All rights reserved.

  1. Comparison of Collection Schemes of Municipal Solid Waste Metallic Fraction: The Impacts on Global Warming Potential for the Case of the Helsinki Metropolitan Area, Finland

    Directory of Open Access Journals (Sweden)

    Kari Heiskanen

    2012-10-01

    Full Text Available In this research article the sustainability of different practices to collect the metal fraction of household waste in the Helsinki metropolitan area, Finland is examined. The study is carried out by calculating and comparing the greenhouse gas reduction potential of optional practices for collecting the metal fraction of household waste in the Helsinki metropolitan area, Finland. In order to locate the greenhouse gas reduction potential of the separate collection of the metallic fraction of municipal solid waste (MSW collected from residential sources, a comparative carbon footprint analysis using Life Cycle Assessment (LCA on six different waste management scenarios is carried out. The modeled system consisted of a waste collection system, transportation, and different waste management alternatives, including on-site separation, separation at the waste management facility as well as metallurgical recovery of separated scrap. The results show that, in terms of greenhouse gas emissions, separate collection and recycling of the metallic fraction of solid MSW at residential properties is the preferable option compared to a scenario with no source sorting and incineration of everything. According to this research scenario where the metal fraction of solid household waste was not source-separated or collected separately have clearly higher greenhouse gas emissions compared to all the other scenarios with separate collection for metals. In addition, metal recycling by regional collection points has considerably lower greenhouse gas emission potential than metal recycling by collection directly from residential properties.

  2. PHYSICO-CHEMICAL PROPERTIES OF THE SOLID AND LIQUID WASTE PRODUCTS FROM THE HEAVY METAL CONTAMINATED ENERGY CROPS GASIFICATION PROCESS

    Directory of Open Access Journals (Sweden)

    Sebastian Werle

    2017-02-01

    Full Text Available The paper presents the results of basic physico-chemical properties of solid (ash and liquid (tar waste products of the gasification process of the heavy metal contaminated energy crops. The gasification process has carried out in a laboratory fixed bed reactor. Three types of energy crops: Miscanthus x giganteus, Sida hermaphrodita and Spartina Pectinata were used. The experimental plots were established on heavy metal contaminated arable land located in Bytom (southern part of Poland, Silesian Voivodship.

  3. Spatial assessment of potential ecological risk of heavy metals in soils from informal e-waste recycling in Ghana.

    Science.gov (United States)

    Kyere, Vincent Nartey; Greve, Klaus; Atiemo, Sampson Manukure; Ephraim, James

    2017-01-01

    The rapidly increasing annual global volume of e-waste, and of its inherently valuable fraction, has created an opportunity for individuals in Agbogbloshie, Accra, Ghana to make a living by using unconventional, uncontrolled, primitive and crude procedures to recycle and recover valuable metals from this waste. The current form of recycling procedures releases hazardous fractions, such as heavy metals, into the soil, posing a significant risk to the environment and human health. Using a handheld global positioning system, 132 soil samples based on 100 m grid intervals were collected and analysed for cadmium (Cd), chromium (Cr), copper (Cu), mercury (Hg), lead (Pb) and zinc (Zn). Using geostatistical techniques and sediment quality guidelines, this research seeks to assess the potential risk these heavy metals posed to the proposed Korle Ecological Restoration Zone by informal e-waste processing site in Agbogbloshie, Accra, Ghana. Analysis of heavy metals revealed concentrations exceeded the regulatory limits of both Dutch and Canadian soil quality and guidance values, and that the ecological risk posed by the heavy metals extended beyond the main burning and dismantling sites of the informal recyclers to the school, residential, recreational, clinic, farm and worship areas. The heavy metals Cr, Cu, Pb and Zn had normal distribution, spatial variability, and spatial autocorrelation. Further analysis revealed the decreasing order of toxicity, Hg>Cd>Pb> Cu>Zn>Cr, of contributing significantly to the potential ecological risk in the study area.

  4. Spatial assessment of potential ecological risk of heavy metals in soils from informal e-waste recycling in Ghana

    Directory of Open Access Journals (Sweden)

    Vincent Nartey Kyere

    2017-10-01

    Full Text Available The rapidly increasing annual global volume of e-waste, and of its inherently valuable fraction, has created an opportunity for individuals in Agbogbloshie, Accra, Ghana to make a living by using unconventional, uncontrolled, primitive and crude procedures to recycle and recover valuable metals from this waste. The current form of recycling procedures releases hazardous fractions, such as heavy metals, into the soil, posing a significant risk to the environment and human health. Using a handheld global positioning system, 132 soil samples based on 100 m grid intervals were collected and analysed for cadmium (Cd, chromium (Cr, copper (Cu, mercury (Hg, lead (Pb and zinc (Zn. Using geostatistical techniques and sediment quality guidelines, this research seeks to assess the potential risk these heavy metals posed to the proposed Korle Ecological Restoration Zone by informal e-waste processing site in Agbogbloshie, Accra, Ghana. Analysis of heavy metals revealed concentrations exceeded the regulatory limits of both Dutch and Canadian soil quality and guidance values, and that the ecological risk posed by the heavy metals extended beyond the main burning and dismantling sites of the informal recyclers to the school, residential, recreational, clinic, farm and worship areas. The heavy metals Cr, Cu, Pb and Zn had normal distribution, spatial variability, and spatial autocorrelation. Further analysis revealed the decreasing order of toxicity, Hg>Cd>Pb> Cu>Zn>Cr, of contributing significantly to the potential ecological risk in the study area.

  5. Contamination and risk of heavy metals in soils and sediments from a typical plastic waste recycling area in North China.

    Science.gov (United States)

    Tang, Zhenwu; Zhang, Lianzhen; Huang, Qifei; Yang, Yufei; Nie, Zhiqiang; Cheng, Jiali; Yang, Jun; Wang, Yuwen; Chai, Miao

    2015-12-01

    Plastic wastes are increasingly being recycled in many countries. However, available information on the metals released into the environment during recycling processes is rare. In this study, the contamination features and risks of eight heavy metals in soils and sediments were investigated in Wen'an, a typical plastic recycling area in North China. The surface soils and sediments have suffered from moderate to high metal pollution and in particular, high Cd and Hg pollution. The mean concentrations of Cd and Hg were 0.355 and 0.408 mg kg(-1), respectively, in the soils and 1.53 and 2.10 mg kg(-1), respectively, in the sediments. The findings suggested that there is considerable to high potential ecological risks in more than half of the soils and high potential ecological risk in almost all sediments. Although the health risk levels from exposure to soil metals were acceptable for adults, the non-carcinogenic risks to local children exceeded the acceptable level. Source assessment indicated that heavy metals in soils and sediments were mainly derived from inputs from poorly controlled plastic waste recycling operations in this area. The results suggested that the risks associated with heavy metal pollution from plastic waste recycling should be of great concern. Copyright © 2015 Elsevier Inc. All rights reserved.

  6. A particulate model of solid waste incineration in a fluidized bed combining combustion and heavy metal vaporization

    Energy Technology Data Exchange (ETDEWEB)

    Mazza, G. [Facultad de Ingenieria, Departamento de Quimica, Universidad Nacional del Comahue, UE Neuquen (CONICET - UNCo), Buenos Aires 1400, 8300 Neuquen (Argentina); Falcoz, Q.; Gauthier, D.; Flamant, G. [Laboratoire Procedes Materiaux et Energie Solaire (CNRS-PROMES), 7 Rue du Four Solaire, Odeillo, 66120 Font-Romeu (France)

    2009-11-15

    This study aims to develop a particulate model combining solid waste particle combustion and heavy metal vaporization from burning particles during MSW incineration in a fluidized bed. The original approach for this model combines an asymptotic combustion model for the carbonaceous solid combustion and a shrinking core model to describe the heavy metal vaporization. A parametric study is presented. The global metal vaporization process is strongly influenced by temperature. Internal mass transfer controls the metal vaporization rate at low temperatures. At high temperatures, the chemical reactions associated with particle combustion control the metal vaporization rate. A comparison between the simulation results and experimental data obtained with a laboratory-scale fluid bed incinerator and Cd-spiked particles shows that the heavy metal vaporization is correctly predicted by the model. The predictions are better at higher temperatures because of the temperature gradient inside the particle. Future development of the model will take this into account. (author)

  7. Screening of heavy metal containing waste types for use as raw material in Arctic clay-based bricks.

    Science.gov (United States)

    Belmonte, Louise Josefine; Ottosen, Lisbeth M; Kirkelund, Gunvor Marie; Jensen, Pernille Erland; Vestbø, Andreas Peter

    2016-11-10

    In the vulnerable Arctic environment, the impact of especially hazardous wastes can have severe consequences and the reduction and safe handling of these waste types are therefore an important issue. In this study, two groups of heavy metal containing particulate waste materials, municipal solid waste incineration (MSWI) fly and bottom ashes and mine tailings (i.e., residues from the mineral resource industry) from Greenland were screened in order to determine their suitability as secondary resources in clay-based brick production. Small clay discs, containing 20 or 40% of the different particulate waste materials, were fired and material properties and heavy metal leaching tests were conducted before and after firing. Remediation techniques (washing in distilled water and electrodialytical treatment) applied to the fly ash reduced leaching before firing. The mine tailings and bottom ash brick discs obtained satisfactory densities (1669-2007 kg/m3) and open porosities (27.9-39.9%). In contrast, the fly ash brick discs had low densities (1313-1578 kg/m3) and high open porosities (42.1-51. %). However, leaching tests on crushed brick discs revealed that heavy metals generally became more available after firing for all the investigated materials and that further optimisation is therefore necessary prior to incorporation in bricks.

  8. Precipitation of heavy metals by lime mud waste of pulp and paper mill

    Directory of Open Access Journals (Sweden)

    Puek Tantriratna

    2004-02-01

    Full Text Available Precipitation of heavy metals in synthetic and actual wastewater with lime mud (solid waste generated from the pulp and paper production process was experimented using Jar-tests. Separate synthetic wastewater samples were prepared for each of the following heavy metals: lead (1,433.7 mgPb2+/L, chromium (506.7 mgCr3+/L, cadmium (1,095 mgCd2+/L and mercury (9.37 mgHg2+/L. The actual wastewater was tanning wastewater containing 74.49 mgCr3+/L and COD wastewater containing 683 mgHg2+/L. Adjustments of pH in the acidic range, pH 2-7, were made for each type of synthetic wastewater except for the Hg synthetic wastewater. The optimum conditions obtained from the tests of the synthetic wastewater were used for theactual wastewater samples. Precipitation of heavy metals with lime mud was effective as indicated by the removal efficiency as high as 90% up for Pb, Cd and Hg and 100% for Cr. However, the removal efficiency for the Hg-COD wastewater was only 67%. The precipitating pH was in the range of 10 up, which is the common pH range for metal carbonate precipitation. The optimum dosage of lime mud for Pb, Cr, Cd and Hg synthetic wastewater was 0.4-1.0 g/L, 2.0-4.0 g/L, 1.6-2.0g/L and 0.8 g/L, respectively. While the optimum dosage of lime mud for precipitating chromium in tanning wastewater was 3.8 g/L and 3.6 g/L for precipitating mercury in COD wastewater.

  9. Removal heavy metals and sulphate from waste waters by sulphate-reducing bacteria

    Directory of Open Access Journals (Sweden)

    Kušnierová Mária

    2000-09-01

    Full Text Available This article is devoted to the process of bacterial sulphate reduction, which is used to removal of heavy metals and sulphate ions from waste waters.The life of animals and plants depends on the existence of microscopic organisms – microorganisms (MO, which play an important role in cycle changes of biogenic elements on the earth. The sulphur cycle in the nature is considered as one of the oldest and most significant biological systems (Fig. 1. The sulphate-reducing bacteria (SRB miss the assimilatory part of the cycle and produce sulphides. The microbial population of this dissimilatory part is called “sulfuretum”. The SRB can be found in anaerobic mud and sediments of freshwater, thermal or non-thermal sulphur springs, mining waters from sulphide deposits, oil deposits, sea and ocean beds, and in the gastrointestinal tract of man and animals. The SRB represent a group of chemoorganotrophic, strictly anaerobic and gramnegative bacteria, which exhibit a great morphological and physiological diversity. Despite of their considerable morphological variety, they have one property in common, which is the ability to utilise preferentially sulphates (occasionally sulphites, thiosulphates, tetrathionates as electron acceptors, which are reduced to sulphides, during anaerobic respiration. The electron donors in these processes are simple organic compounds as lactate, malate, etc.,(heterotrophically reduction or gaseous hydrogen (autotrophically reduction. SRB can produce a considerable amount of hydrogen sulphide, which reacts easily in aqueous solution with the cations of heavy metals, forming metal sulphides that have low solubility. The bacterial sulphate reduction can be used for the treatment of acid mine drainage waters, which is considered to be the major problem associated with mining activities.In order to remove heavy metals from waste waters, e.g., from galvanizing plants, mine waters (Smolnik, Šobov locality and metallurgic plants (works

  10. Impacts of long-term waste-water irrigation on the development of sandy Luvisols: consequences for metal pollutant distributions

    NARCIS (Netherlands)

    Oort, van F.; Jongmans, A.G.; Lamy, I.; Baize, D.; Chevallier, P.

    2008-01-01

    Studies relating macro- and microscopic aspects of impacts of long-term contaminative practices on soils are scarce. We performed such an approach by assessing the fate of metal pollutants in an area close to Paris, where sandy Luvisols were irrigated for 100 years with urban waste water. As a

  11. Immobilization of metals in contaminated soil from E-waste recycling site by dairy-manure-derived biochar.

    Science.gov (United States)

    Chen, Zhiliang; Zhang, Jianqiang; Liu, Minchao; Wu, Yingxin; Yuan, Zhihui

    2017-08-24

    E-waste is a growing concern around the world and varieties of abandoned E-waste recycling sites, especially in urban area, need to remediate immediately. The impacts of dairy-manure-derived biochars (BCs) on the amelioration of soil properties, the changes in the morphologies as well as the mobility of metals were studied to test their efficacy in immobilization of metals for a potential restoration of vegetation landscape in abandoned E-waste recycling site. The amendment with BCs produced positive effects on bioavailability and mobility reduction for Pb, Cd, Zn and Cu depending on BC ratio and incubation time. The BCs promoted the transformation of species of heavy metals to a more stable fraction, and the metals concentrations in Toxicity Characteristic Leaching Procedure extract declined significantly, especially Pb and Cu. Besides, the BCs ameliorated the substrate with increasing the soil pH, cations exchangeable capacity and available phosphorous, which suggested BC as a potential amendment material for abandoned E-waste recycling sites before restoration of vegetation landscape. Generally, the BC modified by alkaline treatment has a higher efficacy, probably due to increase of specific surface area and porosity as well as the functional groups after alkaline treatment.

  12. Electrodialytic removal of heavy metals from municipal solid waste incineration fly ash using ammonium citrate as assisting agent

    DEFF Research Database (Denmark)

    Pedersen, Anne Juul; Ottosen, Lisbeth M.; Villumsen, Arne

    2005-01-01

    Electrodialytic remediation, an electrochemically assisted separation method, has previ-ously shown potential for removal of heavy metals from municipal solid waste incineration (MSWI) fly ashes. In this work electrodialytic remediation of MSWI fly ash using ammonium citrate as assisting agent...

  13. Effects of climate change on the toxicity of soils polluted by metal mine wastes to Enchytraeus crypticus

    NARCIS (Netherlands)

    Gonzalez Alcaraz, M.N.; Tsitsiou, E.; Wieldraaijer, R.; Verweij, R.A.; van Gestel, C.A.M.

    2015-01-01

    The present study aimed to assess the effects of climate change on the toxicity of metal-polluted soils. Bioassays with Enchytraeus crypticus were performed in soils polluted by mine wastes (mine tailing, forest, and watercourse) and under different combinations of temperature (20°C and 25°C) and

  14. Leaching characteristics of heavy metals and brominated flame retardants from waste printed circuit boards

    Energy Technology Data Exchange (ETDEWEB)

    Zhou, Xiaoyu [State Environmental Protection Key Laboratory of Environmental Risk Assessment and Control on Chemical Process, East China University of Science and Technology, Shanghai 200237 (China); Guo, Jie, E-mail: guojie@ecust.edu.cn [State Environmental Protection Key Laboratory of Environmental Risk Assessment and Control on Chemical Process, East China University of Science and Technology, Shanghai 200237 (China); Lin, Kuangfei [State Environmental Protection Key Laboratory of Environmental Risk Assessment and Control on Chemical Process, East China University of Science and Technology, Shanghai 200237 (China); Shanghai Key Laboratory of Functional Materials Chemistry, East China University of Science and Technology, Shanghai 200237 (China); Huang, Kai; Deng, Jingjing [State Environmental Protection Key Laboratory of Environmental Risk Assessment and Control on Chemical Process, East China University of Science and Technology, Shanghai 200237 (China)

    2013-02-15

    Highlights: ► Cu and Pb were the most leachable heavy metals in WPCBs according to TCLP and SPLP. ► Penta-BDE congeners were dominated in all extracts. ► High dissolved organic matter condition promoted the BFRs leaching rate. ► Leaching from WPCBs was a significant emission source of BFRs in landfill. -- Abstract: Leaching assessment on five heavy metals (copper, zinc, lead, nickel and cadmium) and two brominated flame retardants (BFRs), polybrominated diphenyl ethers (PBDEs) and tetrabromobisphenol A (TBBPA), from waste printed circuit boards (WPCBs) were conducted using various leaching methods. The mean leaching concentrations of copper were the highest in both toxicity characteristic leaching procedures (TCLP) and synthetic precipitation leaching procedures (SPLP) tests at 8.6 mg/L and 1.1 mg/L, while only lead (6.2 mg/L) exceeded the TCLP criteria and Chinese EPA regulatory limit (both 5.0 mg/L). However, PBDEs and TBBPA were not detected in TCLP and SPLP tests. Then the BFRs leaching trends and potential leachabilities were further investigated in actual landfill leachates using a modified method. Leaching characteristics that fast-leaching initially followed by slow-desorption over time were generally observed. In landfill leachate tests, the highest leaching concentrations of PBDEs and TBBPA were determined at 30.39 and 12.27 μg/L. Meanwhile, the highest leaching rates were estimated to reach 0.08% and 1.00%, respectively, which were significantly influenced by the dissolved organic carbon contents of extracts, the hydrophobicities of target BFRs and the specific surface areas of WPCBs materials. These results proved that leaching from WPCBs was a significant emission source of BFRs in landfill and electronic waste recycling dumpsite.

  15. The use of waste mussel shells for the adsorption of dyes and heavy metals

    Science.gov (United States)

    Papadimitriou, Chrysi A.; Krey, Grigorios; Stamatis, Nikolaos; Kallaniotis, Argyris

    2016-04-01

    Mussel culture is very important sector of the Greek agricultural economy. The majority of mussel culture activities take place in the area of Central Macedonia, Greece, 60% of total mussel production in Greece producing almost 12 tons of waste mussels shells on a daily basis. Currently there is no legislation concerning the disposal of mussel shells. In the present study the waste shells were used for the removal of dyes and heavy metals from aqueous solutions while powdered mussel shells were added in activated sludge processes for the removal of hexavalent chromium. Mussel shells were cleaned, dried and then crushed in order to form a powder. Powdered mussels shells were used in standard adsorption experiments for the removal of methylene blue and methyl red as well as for the removal of Cr (VI), Cd and Cu. Moreover the powdered mussel shells were added in laboratory scale activated sludge reactors treating synthetic wastewater with hexavalent chromium, in order investigate the effects in activated sludge processes and their potential attribution to the removal of hexavalent chromium. Adsorption experiments indicated almost 100% color removal, while adsorption was directly proportional to the amount of powdered mussel shells added in each case. The isotherms calculated for the case of methylene blue indicated similar adsorption capacity and properties to those of the commercially available activated carbon SAE 2, Norit. High removal efficiencies were observed for the metals, especially in the case of chromium and copper. The addition of powdered mussel shells in the activated sludge processes enhanced the removal of chromium and phosphorus, while enabled the formation of heavier activated sludge flocs and thus enhanced the settling properties of the activated sludge.

  16. Atmospheric emissions of typical toxic heavy metals from open burning of municipal solid waste in China

    Science.gov (United States)

    Wang, Yan; Cheng, Ke; Wu, Weidong; Tian, Hezhong; Yi, Peng; Zhi, Guorui; Fan, Jing; Liu, Shuhan

    2017-03-01

    Municipal solid waste (MSW) contains considerable hazardous components and the widely-distributed open MSW burning in heavily-populated urban areas can cause direct exposure of hazardous materials to citizens. By determining the best available representation of composition-varying and time-varying emission factors with fuzzy mathematics method and S-shape curves, a comprehensive atmospheric emission inventories of 9 typical toxic heavy metals (THMs, e.g. mercury (Hg), arsenic (As), lead (Pb), cadmium (Cd), chromium (Cr), selenium (Se), copper (Cu), zinc (Zn), and nickel (Ni)) from open MSW burning activities in China is established during the period of 2000-2013 for the first time. Further, the emissions in 2013 are allocated at a high spatial resolution of 0.5° × 0.5° grid by surrogate indexes. The results show that 9 typical THMs emissions from open MSW burning are estimated at 21.25 t for Hg, 131.52 t for As, 97.12 t for Pb, 10.12 t for Cd, 50.58 t for Cr, 81.95 t for Se, 382.42 t for Cu, 1790.70 t for Zn, and 43.50 t for Ni, respectively. In terms of spatial variation, the majority of emissions are concentrated in relatively developed and densely-populated regions, especially for the eastern, central and southern regions. Moreover, future emissions are also projected for the period of 2015-2030 based on different scenarios of the independent and collaborative effects of control proposals including minimizing waste, improving MSW incineration ratio, and enhancing waste sorting and recycling, etc. The collaborative effect of the above proposals is expected to bring the most effective reduction to THMs emissions from open MSW burning in China except for Hg. The results will be supplementary to all anthropogenic emissions and useful for relevant policy-making and the improvement of urban air quality as well as human health.

  17. Anticipated Degradation Modes of Metallic Engineered Barriers for High-Level Nuclear Waste Repositories

    Science.gov (United States)

    Rodríguez, Martín A.

    2014-03-01

    Metallic engineered barriers must provide a period of absolute containment to high-level radioactive waste in geological repositories. Candidate materials include copper alloys, carbon steels, stainless steels, nickel alloys, and titanium alloys. The national programs of nuclear waste management have to identify and assess the anticipated degradation modes of the selected materials in the corresponding repository environment, which evolves in time. Commonly assessed degradation modes include general corrosion, localized corrosion, stress-corrosion cracking, hydrogen-assisted cracking, and microbiologically influenced corrosion. Laboratory testing and modeling in metallurgical and environmental conditions of similar and higher aggressiveness than those expected in service conditions are used to evaluate the corrosion resistance of the materials. This review focuses on the anticipated degradation modes of the selected or reference materials as corrosion-resistant barriers in nuclear repositories. These degradation modes depend not only on the selected alloy but also on the near-field environment. The evolution of the near-field environment varies for saturated and unsaturated repositories considering backfilled and unbackfilled conditions. In saturated repositories, localized corrosion and stress-corrosion cracking may occur in the initial aerobic stage, while general corrosion and hydrogen-assisted cracking are the main degradation modes in the anaerobic stage. Unsaturated repositories would provide an oxidizing environment during the entire repository lifetime. Microbiologically influenced corrosion may be avoided or minimized by selecting an appropriate backfill material. Radiation effects are negligible provided that a thick-walled container or an inner shielding container is used.

  18. Assessment of methane production from shredder waste in landfills: The influence of temperature, moisture and metals

    DEFF Research Database (Denmark)

    Fathi Aghdam, Ehsan; Scheutz, Charlotte; Kjeldsen, Peter

    2017-01-01

    In this study, methane (CH4) production rates from shredder waste (SW) were determined by incubation of waste samples over a period of 230days under different operating conditions, and first-order decay kinetic constants (k-values) were calculated. SW and sterilized SW were incubated under differ...... in landfilled SW are thus most likely due to the consumption of existing CO2 in the produced biogas and the produced H2 by biocorrosion of aluminum and zinc by methanogens....... different temperatures (20-25°C, 37°C, and 55°C), moisture contents (35% and 75% w/w) and amounts of inoculum (5% and 30% of the samples wet weight). The biochemical methane potential (BMP) from different types of SW (fresh, old and sieved) was determined and compared. The ability of metals (iron, aluminum.......235-0.488yr(-1) at 55°C, indicating that higher temperatures resulted in higher k-values. It was observed that H2 can be produced by biocorrosion of iron, aluminum, and zinc and it was shown that produced H2 can be utilized by hydrogenotrophic methanogens to convert CO2 to CH4. Addition of iron and copper...

  19. An LCA model for waste incineration enhanced with new technologies for metal recovery and application to the case of Switzerland.

    Science.gov (United States)

    Boesch, Michael E; Vadenbo, Carl; Saner, Dominik; Huter, Christoph; Hellweg, Stefanie

    2014-02-01

    A process model of municipal solid waste incinerators (MSWIs) and new technologies for metal recovery from combustion residues was developed. The environmental impact is modeled as a function of waste composition as well as waste treatment and material recovery technologies. The model includes combustion with a grate incinerator, several flue gas treatment technologies, electricity and steam production from waste heat recovery, metal recovery from slag and fly ash, and landfilling of residues and can be tailored to specific plants and sites (software tools can be downloaded free of charge). Application of the model to Switzerland shows that the treatment of one tonne of municipal solid waste results on average in 425 kg CO2-eq. generated in the incineration process, and 54 kg CO2-eq. accrue in upstream processes such as waste transport and the production of operating materials. Downstream processes, i.e. residue disposal, generates 5 kg CO2-eq. Savings from energy recovery are in the range of 67 to 752 kg CO2-eq. depending on the assumptions regarding the substituted energy production, while the recovery of metals from slag and fly ash currently results in a net saving of approximately 35 kg CO2-eq. A similar impact pattern is observed when assessing the MSWI model for aggregated environmental impacts (ReCiPe) and for non-renewable resource consumption (cumulative exergy demand), except that direct emissions have less and no relevance, respectively, on the total score. The study illustrates that MSWI plants can be an important element of industrial ecology as they provide waste disposal services and can help to close material and energetic cycles. Copyright © 2013 Elsevier Ltd. All rights reserved.

  20. Precious metal recovery from waste printed circuit boards using cyanide and non-cyanide lixiviants--A review.

    Science.gov (United States)

    Akcil, Ata; Erust, Ceren; Gahan, Chandra Sekhar; Ozgun, Mehmet; Sahin, Merve; Tuncuk, Aysenur

    2015-11-01

    Waste generated by the electrical and electronic devices is huge concern worldwide. With decreasing life cycle of most electronic devices and unavailability of the suitable recycling technologies it is expected to have huge electronic and electrical wastes to be generated in the coming years. The environmental threats caused by the disposal and incineration of electronic waste starting from the atmosphere to the aquatic and terrestrial living system have raised high alerts and concerns on the gases produced (dioxins, furans, polybrominated organic pollutants, and polycyclic aromatic hydrocarbons) by thermal treatments and can cause serious health problems if the flue gas cleaning systems are not developed and implemented. Apart from that there can be also dissolution of heavy metals released to the ground water from the landfill sites. As all these electronic and electrical waste do posses richness in the metal values it would be worth recovering the metal content and protect the environmental from the pollution. Cyanide leaching has been a successful technology worldwide for the recovery of precious metals (especially Au and Ag) from ores/concentrates/waste materials. Nevertheless, cyanide is always preferred over others because of its potential to deliver high recovery with a cheaper cost. Cyanidation process also increases the additional work of effluent treatment prior to disposal. Several non-cyanide leaching processes have been developed considering toxic nature and handling problems of cyanide with non-toxic lixiviants such as thiourea, thiosulphate, aqua regia and iodine. Therefore, several recycling technologies have been developed using cyanide or non-cyanide leaching methods to recover precious and valuable metals. Copyright © 2015 Elsevier Ltd. All rights reserved.

  1. Physical and thermal waste utilisation in the nonferrous metal industry; Stoffliche und thermische Abfallverwertung in der Nichteisenmetallindustrie

    Energy Technology Data Exchange (ETDEWEB)

    Sowa, F. [DMT-Gesellschaft fuer Forschung und Pruefung mbH, Essen (Germany)

    1998-09-01

    In its amended form the German Household Waste Technical Code favours physical and thermal utilisation of wastes against dumping. Industrial processes offer various ways of utilising wastes with a high calorific value, e.g. in nonferrous metal production. Besides portraying this branch of industry in Germany the present paper investigates to what extent this topic has already found coverage and what potential it holds for the utilisation of wastes. By way of example it describes a successful demonstration of the physical utilisation of sewage sludge in lead production. [Deutsch] Die Neugestaltung der TA Siedlungsabfall favorisiert die thermische und stoffliche Verwertung von Abfallstoffen gegenueber der Deponierung. Moeglichkeiten fuer die Verwertung heizwertreicher Abfaelle bieten auch industrielle Produktionsprozesse, z.B. auch in der Nichteisenmetallerzeugung. Neben einer Charakterisierung der Branche wird untersucht, inwieweit dieses Thema bereits aufgegriffen worden ist und welches Verwertungspotential zur Verfuegung steht. An einem Beispiel wird die erfolgreiche Demonstration der stofflichen Verwertung von Klaerschlamm in der Bleierzeugung dargestellt. (orig.)

  2. Sustainable sources of biomass for bioremediation of heavy metals in waste water derived from coal-fired power generation.

    Science.gov (United States)

    Saunders, Richard J; Paul, Nicholas A; Hu, Yi; de Nys, Rocky

    2012-01-01

    Biosorption of heavy metals using dried algal biomass has been extensively described but rarely implemented. We contend this is because available algal biomass is a valuable product with a ready market. Therefore, we considered an alternative and practical approach to algal bioremediation in which algae were cultured directly in the waste water stream. We cultured three species of algae with and without nutrient addition in water that was contaminated with heavy metals from an Ash Dam associated with coal-fired power generation and tested metal uptake and bioremediation potential. All species achieved high concentrations of heavy metals (to 8% dry mass). Two key elements, V and As, reached concentrations in the biomass of 1543 mg.kg(-1) DW and 137 mg.kg(-1) DW. Growth rates were reduced by more than half in neat Ash Dam water than when nutrients were supplied in excess. Growth rate and bioconcentration were positively correlated for most elements, but some elements (e.g. Cd, Zn) were concentrated more when growth rates were lower, indicating the potential to tailor bioremediation depending on the pollutant. The cosmopolitan nature of the macroalgae studied, and their ability to grow and concentrate a suite of heavy metals from industrial wastes, highlights a clear benefit in the practical application of waste water bioremediation.

  3. Relation between leaching characteristics of heavy metals and physical properties of fly ashes from typical municipal solid waste incinerators.

    Science.gov (United States)

    Ni, Peng; Li, Hailong; Zhao, Yongchun; Zhang, Junying; Zheng, Chuguang

    2017-09-01

    Due to the alkalinity and high concentration of potentially hazardous heavy metals, fly ash from a municipal solid waste (MSW) incinerator is classified as hazardous waste, which should be of particular concern. Physical and chemical characterizations of the contrasted fly ashes were investigated to explore the relation between leaching characteristics of heavy metals and physical properties of fly ashes. The results showed that CaClOH, NaCl, Ca(OH)2, KCl and SiO2 were primary mineral compositions in the MSWI fly ashes, and the particle size distribution of fly ash ranged between 10 μm and 300 μm. The smaller the particle size distribution of fly ash, the larger the BET-specific surface area, which was beneficial to the leaching of heavy metals. As a result of various pores, it easily accumulated heavy metals as well. The leaching tests exhibited a high leachability of heavy metals and the leaching concentration of Pb in almost all of the fly ash samples went far beyond the Standard for Pollution Control on the Landfill Site of Municipal Solid Waste. Thereupon, it is necessary to establish proper disposal systems and management strategies for environmental protection based on the characteristics of MSW incineration (MSWI) fly ash in China.

  4. Flow analysis of heavy metals in a pilot-scale incinerator for residues from waste electrical and electronic equipment dismantling.

    Science.gov (United States)

    Long, Yu-Yang; Feng, Yi-Jian; Cai, Si-Shi; Ding, Wei-Xu; Shen, Dong-Sheng

    2013-10-15

    The large amount of residues generated from dismantling waste electrical and electronic equipment (WEEE) results in a considerable environmental burden. We used material flow analysis to investigate heavy metal behavior in an incineration plant in China used exclusively to incinerate residues from WEEE dismantling. The heavy metals tested were enriched in the bottom and fly ashes after incineration. However, the contents of heavy metals in the bottom ash, fly ash and exhaust gas do not have a significant correlation with that of the input waste. The evaporation and recondensation behavior of heavy metals caused their contents to differ with air pollution control equipment because of the temperature difference during gas venting. Among the heavy metals tested, Cd had the strongest tendency to transfer during incineration (TCd=69.5%) because it had the lowest melting point, followed by Cu, Ni, Pb and Zn. The exchangeable and residual fractions of heavy metals increased substantially in the incineration products compared with that of the input residues. Although the mass of residues from WEEE dismantling can be reduced by 70% by incineration, the safe disposal of the metal-enriched bottom and fly ashes is still required. Copyright © 2013 Elsevier B.V. All rights reserved.

  5. Stabilization treatment of the heavy metals in fly ash from municipal solid waste incineration using diisopropyl dithiophosphate potassium.

    Science.gov (United States)

    Xu, Ying; Chen, Yu; Feng, Yueyang

    2013-01-01

    A stabilization treatment was developed for heavy metals in fly ash from municipal solid waste incineration using the heavy metal chelator diisopropyl dithiophosphate potassium (DDP). The mechanism and effect of the DDP chelator treatment on heavy metals in the fly ash was also studied, along with the form transformation rules of the heavy metals after DDP chelator treatment. The results show that 1% DDP achieves a stabilization rate of over 95% for Pb, Zn, and Cd. The effect of DDP was better than that of inorganic stabilizers such as sodium sulphide and lime. The heavy metal concentrations in the leachate after the treatment were lower than those required by the Pollution Control Standards for Hazardous Waste Landfill (GB18598-2001). At pH 1-13, the heavy metal concentrations in the fly ash leachate were far lower than those using the inorganic stabilizers sodium sulphide and lime. DDP retains its stabilizing effect under a broader pH range. After stabilization treatment, the heavy metals in the exchangeable fraction and those bound to carbonates were mainly transformed into those bound to organic matter. This process decreases the unstable content and reduces the risk of secondary pollution of the stabilized products in the environment.

  6. Layer modeling of zinc removal from metallic mixture of waste printed circuit boards by vacuum distillation.

    Science.gov (United States)

    Gao, Yujie; Li, Xingang; Ding, Hui

    2015-08-01

    A layer model was established to elucidate the mechanism of zinc removal from the metallic mixture of waste printed circuit boards by vacuum distillation. The removal process was optimized by response surface methodology, and the optimum operating conditions were the chamber pressure of 0.1Pa, heating temperature of 923K, heating time of 60.0min, particle size of 70 mesh (0.212mm) and initial mass of 5.25g. Evaporation efficiency of zinc, the response variable, was 99.79%, which indicates that the zinc can be efficiently removed. Based on the experimental results, a mathematical model, which bears on layer structure, evaporation, mass transfer and condensation, interprets the mechanism of the variable effects. Especially, in order to reveal blocking effect on the zinc removal, the Blake-Kozeny-Burke-Plummer equation was introduced into the mass transfer process. The layer model can be applied to a wider range of metal removal by vacuum distillation. Copyright © 2015 Elsevier Ltd. All rights reserved.

  7. Fate of metals and emissions of organic pollutants from torrefaction of waste wood, MSW, and RDF.

    Science.gov (United States)

    Edo, Mar; Skoglund, Nils; Gao, Qiuju; Persson, Per-Erik; Jansson, Stina

    2017-10-01

    Torrefaction of municipal solid waste (MSW), refuse-derived fuel (RDF), and demolition and construction wood (DC) was performed at 220°C and a residence time of 90min in a bench-scale reactor. The levels of toxic polychlorinated dibenzo-p-dioxins (PCDD) and dibenzofurans (PCDF) contained in emission from the torrefaction process were evaluated. In addition, main ash-forming elements and trace metals in the raw feedstock and char were determined. The use of MSW in fuel blends with DC resulted in lower PCDD and PCDF emissions after torrefaction, compared with the RDF blends. The migration of chlorine from the feedstock to the gas phase reduces the chlorine content of the char which may reduce the risk of alkali chloride-corrosion in char combustion. However, trace metals catalytically active in the formation of PCDD and PCDF remain in the char, thereby may promote PCDD and PCDF formation during subsequent char combustion for energy recovery; this formation is less extensive than when the feedstock is used. Copyright © 2017 Elsevier Ltd. All rights reserved.

  8. Plant and fungal biodiversity from metal mine wastes under remediation at Zimapan, Hidalgo, Mexico

    Energy Technology Data Exchange (ETDEWEB)

    Ortega-Larrocea, Maria del Pilar [Departamento de Edafologia, Instituto de Geologia, Universidad Nacional Autonoma de Mexico (UNAM) (Mexico); Xoconostle-Cazares, Beatriz [Departamento de Biotecnologia y Bioingenieria, Centro de Investigacion y de Estudios Avanzados del Instituto Politecnico Nacional, Av. IPN 2508, Zacatenco 07360, D.F. (Mexico); Maldonado-Mendoza, Ignacio E. [Centro Interdisciplinario de Investigacion para el Desarrollo Integral Regional (CIIDIR)-Instituto Politecnico Nacional - Unidad Sinaloa, Blvd. Juan de Dios Batiz Paredes No. 250, Guasave, Sinaloa 81101 (Mexico); Carrillo-Gonzalez, Rogelio [Programa de Edafologia, Colegio de Postgraduados en Ciencias Agricolas, Campus Montecillo, Carretera Mexico-Texcoco, km 36.5, Texcoco, Estado de Mexico 56230 (Mexico); Hernandez-Hernandez, Jani [Departamento de Edafologia, Instituto de Geologia, Universidad Nacional Autonoma de Mexico (UNAM) (Mexico); Garduno, Margarita Diaz [Universidad Autonoma Chapingo, Carretera Mexico-Texcoco, km 38.5, Chapingo, Estado de Mexico 56230 (Mexico); Lopez-Meyer, Melina [Centro Interdisciplinario de Investigacion para el Desarrollo Integral Regional (CIIDIR)-Instituto Politecnico Nacional - Unidad Sinaloa, Blvd. Juan de Dios Batiz Paredes No. 250, Guasave, Sinaloa 81101 (Mexico); Gomez-Flores, Lydia [Departamento de Biotecnologia y Bioingenieria, Centro de Investigacion y de Estudios Avanzados del Instituto Politecnico Nacional, Av. IPN 2508, Zacatenco 07360, D.F. (Mexico); Gonzalez-Chavez, Ma. del Carmen A., E-mail: carmeng@colpos.m [Programa de Edafologia, Colegio de Postgraduados en Ciencias Agricolas, Campus Montecillo, Carretera Mexico-Texcoco, km 36.5, Texcoco, Estado de Mexico 56230 (Mexico)

    2010-05-15

    Plant establishment, presence of arbuscular mycorrhizal fungi (AMF) and other rhizospheric fungi were studied in mine wastes from Zimapan, Hidalgo state, Mexico, using a holistic approach. Two long-term afforested and three non-afforested mine tailings were included in this research. Fifty-six plant species belonging to 29 families were successfully established on the afforested sites, while unmanaged tailings had only a few native plant species colonizing the surrounding soils. Almost all plant roots collected were associated to AMF in these sites. The genus Glomus was the most abundant AMF species found in their rhizosphere; however, the Acaulospora genus was also observed. Other rhizospheric fungi were identified by 18S rDNA sequencing analysis. Their role in these substrates, i.e. biocontrol, pollutant- and organic matter-degradation, and aides that increase plant metal tolerance is discussed. Our results advance the understanding of fungal diversity in sites polluted with metals and present alternative plants for remediation use. - Rhizospheric fungi and organic matter encourage plant vegetation of tailings by pioneers and colonizing species.

  9. ACIDIC REMOVAL OF METALS FROM FLUIDIZED CATALYTIC CRACKING CATALYST WASTE ASSISTED BY ELECTROKINETIC TREATMENT

    Directory of Open Access Journals (Sweden)

    R. B. G. Valt

    2015-06-01

    Full Text Available AbstractOne of the main uses of catalysts in the oil industry is in the fluidized catalytic cracking process, which generates large quantities of waste material after use and regeneration cycles and that can be treated by the electrokinetic remediation technique, in which the contaminant metals are transported by migration. In this study, deactivated FCC catalyst was characterized before and after the electrokinetic remediation process to evaluate the amount of metal removed, and assess structural modifications, in order to indicate a possible use as an adsorbent material. The analyses included pH measurement and the concentration profile of vanadium ions along the reactor, X-ray microtomography, X-ray fluorescence, BET analysis and DTA analysis. The results indicated that 40% of the surface area of the material was recovered in relation to the disabled material, showing an increase in the available area for the adsorption. The remediation process removed nearly 31% of the vanadium and 72% of the P2O5 adhering to the surface of the catalyst, without causing structural or thermal stability changes.

  10. Reduction of heavy metals in residues from the dismantling of waste electrical and electronic equipment before incineration

    Energy Technology Data Exchange (ETDEWEB)

    Long, Yu-Yang; Feng, Yi-Jian; Cai, Si-Shi [Zhejiang Provincial Key Laboratory of Solid Waste Treatment and Recycling, School of Environmental Science and Engineering, Zhejiang Gongshang University, Hangzhou 310012 (China); Hu, Li-Fang [College of Quality and Safety Engineering, China Jiliang University, Hangzhou 310018 (China); Shen, Dong-Sheng, E-mail: shends@zju.edu.cn [Zhejiang Provincial Key Laboratory of Solid Waste Treatment and Recycling, School of Environmental Science and Engineering, Zhejiang Gongshang University, Hangzhou 310012 (China)

    2014-05-01

    Highlights: • The highest metal reduction occurs at a 2.36 mm sieving size. • Washing promotes heavy metal recycling without secondary pollution. • Sieving and washing are environmentally friendly pretreatments for WEEE wastes. - Abstract: Residues disposal from the dismantling of waste electrical and electronic equipment are challenging because of the large waste volumes, degradation-resistance, low density and high heavy metal content. Incineration is advantageous for treating these residues but high heavy metal contents may exist in incinerator input and output streams. We have developed and studied a specialized heavy metal reduction process, which includes sieving and washing for treating residues before incineration. The preferable screen aperture for sieving was found to be 2.36 mm (8 meshes) in this study; using this screen aperture resulted in the removal of approximately 47.2% Cu, 65.9% Zn, 26.5% Pb, 55.4% Ni and 58.8% Cd from the residues. Subsequent washing further reduces the heavy metal content in the residues larger than 2.36 mm, with preferable conditions being 400 rpm rotation speed, 5 min washing duration and liquid-to-solid ratio of 25:1. The highest cumulative removal efficiencies of Cu, Zn, Pb, Ni and Cd after sieving and washing reached 81.1%, 61.4%, 75.8%, 97.2% and 72.7%, respectively. The combined sieving and washing process is environmentally friendly, can be used for the removal of heavy metals from the residues and has benefits in terms of heavy metal recycling.

  11. An LCA model for waste incineration enhanced with new technologies for metal recovery and application to the case of Switzerland

    Energy Technology Data Exchange (ETDEWEB)

    Boesch, Michael E. [Aveny GmbH, Schwandenholzstr. 212, CH-8046 Zürich (Switzerland); Vadenbo, Carl, E-mail: vadenbo@ifu.baug.ethz.ch [ETH Zurich, Institute of Environmental Engineering, Schafmattstrasse 6, CH-8093 Zurich (Switzerland); Saner, Dominik [Swiss Post, Communications, Politics and Social Responsibility, Viktoriastrasse 21, P.O. Box, CH-3030 Berne (Switzerland); Huter, Christoph [City of Zürich, ERZ Entsorgung - Recycling Zürich, Hagenholzstrasse 110, P.O. Box, CH-8050 Zürich (Switzerland); Hellweg, Stefanie [ETH Zurich, Institute of Environmental Engineering, Schafmattstrasse 6, CH-8093 Zurich (Switzerland)

    2014-02-15

    Highlights: • An enhanced process-based LCA model for MSWI is featured and applied in case study. • LCA modeling of recent technological developments for metal recovery from fly ash. • Net release from Swiss MSWI 133 kg CO{sub 2}-eq/tonne waste from attributional LCA perspective. • Net savings from a consequential LCA perspective reach up to 303 kg CO{sub 2}-eq/tonne waste. • Impacts according to ReCiPe and CExD show similar pattern to climate change. - Abstract: A process model of municipal solid waste incinerators (MSWIs) and new technologies for metal recovery from combustion residues was developed. The environmental impact is modeled as a function of waste composition as well as waste treatment and material recovery technologies. The model includes combustion with a grate incinerator, several flue gas treatment technologies, electricity and steam production from waste heat recovery, metal recovery from slag and fly ash, and landfilling of residues and can be tailored to specific plants and sites (software tools can be downloaded free of charge). Application of the model to Switzerland shows that the treatment of one tonne of municipal solid waste results on average in 425 kg CO{sub 2}-eq. generated in the incineration process, and 54 kg CO{sub 2}-eq. accrue in upstream processes such as waste transport and the production of operating materials. Downstream processes, i.e. residue disposal, generates 5 kg CO{sub 2}-eq. Savings from energy recovery are in the range of 67 to 752 kg CO{sub 2}-eq. depending on the assumptions regarding the substituted energy production, while the recovery of metals from slag and fly ash currently results in a net saving of approximately 35 kg CO{sub 2}-eq. A similar impact pattern is observed when assessing the MSWI model for aggregated environmental impacts (ReCiPe) and for non-renewable resource consumption (cumulative exergy demand), except that direct emissions have less and no relevance, respectively, on the total

  12. PREPARATION OF LAYERED DOUBLE HYDROXIDES

    National Research Council Canada - National Science Library

    OGAWA, MAKOTO; INOMATA, KAZUYA

    2011-01-01

    Layered double hydroxides (LDHs) are class of materials with useful properties associated with their anion exchange abilities for a wide range of applications including bio and environmental problems...

  13. Impact of metals in surface matrices from formal and informal electronic-waste recycling around Metro Manila, the Philippines, and intra-Asian comparison

    Energy Technology Data Exchange (ETDEWEB)

    Fujimori, Takashi, E-mail: fujimori.takashi@nies.go.jp [Center for Material Cycles and Waste Management Research, National Institute for Environmental Studies (NIES), 16-2 Onogawa, Tsukuba, 305-8506, Ibaraki (Japan); Takigami, Hidetaka [Center for Material Cycles and Waste Management Research, National Institute for Environmental Studies (NIES), 16-2 Onogawa, Tsukuba, 305-8506, Ibaraki (Japan); Agusa, Tetsuro; Eguchi, Akifumi [Center for Marine Environmental Studies, Ehime University, 2-5 Bunkyo-cho, Matsuyama, 790-8577, Ehime (Japan); Bekki, Kanae [Center for Material Cycles and Waste Management Research, National Institute for Environmental Studies (NIES), 16-2 Onogawa, Tsukuba, 305-8506, Ibaraki (Japan); Division of Pharmaceutical Chemistry and Biology, Graduate School of Natural Science and Technology, Kanazawa University, Kakuma-cho, Kanazawa, 920-1192, Ishikawa (Japan); Yoshida, Aya; Terazono, Atsushi [Center for Material Cycles and Waste Management Research, National Institute for Environmental Studies (NIES), 16-2 Onogawa, Tsukuba, 305-8506, Ibaraki (Japan); Ballesteros, Florencio C. [College of Engineering, University of the Philippines Diliman, Quezon City, 1101 (Philippines)

    2012-06-30

    Highlights: Black-Right-Pointing-Pointer We quantified 11 metals in surface matrices from e-waste recycling sites at the Philippines. Black-Right-Pointing-Pointer Dust had statistical higher levels of metal contamination and health risk compared to soil. Black-Right-Pointing-Pointer Formal and informal sites had different metal contaminations. Black-Right-Pointing-Pointer Intra-Asian comparison provided common insight on metal contamination from e-waste recycling. - Abstract: We report concentrations, enrichment factors, and hazard indicators of 11 metals (Ag, As, Cd, Co, Cu, Fe, In, Mn, Ni, Pb, and Zn) in soil and dust surface matrices from formal and informal electronic waste (e-waste) recycling sites around Metro Manila, the Philippines, referring to soil guidelines and previous data from various e-waste recycling sites in Asia. Surface dust from e-waste recycling sites had higher levels of metal contamination than surface soil. Comparison of formal and informal e-waste recycling sites (hereafter, 'formal' and 'informal') revealed differences in specific contaminants. Formal dust contained a mixture of serious pollutant metals (Ni, Cu, Pb, and Zn) and Cd (polluted modestly), quite high enrichment metals (Ag and In), and crust-derived metals (As, Co, Fe, and Mn). For informal soil, concentration levels of specific metals (Cd, Co, Cu, Mn, Ni, Pb, and Zn) were similar among Asian recycling sites. Formal dust had significantly higher hazardous risk than the other matrices (p < 0.005), excluding informal dust (p = 0.059, almost significant difference). Thus, workers exposed to formal dust should protect themselves from hazardous toxic metals (Pb and Cu). There is also a high health risk for children ingesting surface matrices from informal e-waste recycling sites.

  14. Layered double hydroxides

    DEFF Research Database (Denmark)

    López Rayo, Sandra; Imran, Ahmad; Hansen, Hans Chr. Bruun

    2017-01-01

    A novel zinc (Zn) fertilizer concept based on Zn doped layered double hydroxides (Zn-doped Mg-Fe-LDHs) has been investigated. Zn-doped Mg-Fe-LDHs were synthetized, their chemical composition was analyzed and their nutrient release was studied in buffered solutions with different pH values. Uptake...... the long-term Zn release capacity of LDHs complying with a release-on-demand behavior and serves as proof-of-concept that Zn-doped Mg-Fe-LDHs can be used as Zn fertilizers....

  15. Tetrabromobisphenol A and heavy metal exposure via dust ingestion in an e-waste recycling region in Southeast China.

    Science.gov (United States)

    Wu, Yuanyuan; Li, Yanyan; Kang, Duan; Wang, Jingjing; Zhang, Yanfang; Du, Dongli; Pan, Bishu; Lin, Zhenkun; Huang, Changjiang; Dong, Qiaoxiang

    2016-01-15

    This study was designed to investigate a prevalent brominated flame retardant tetrabromobisphenol A (TBBPA) and four heavy metals of Pb, Cr, As, Cd in dust samples (52 indoor and 52 outdoor) collected from residential houses in an e-waste recycling area in Southeast China. For TBBPA, the mean concentration in indoor dust (3435 ng/g, dw) was higher than that in outdoor dust (1998 ng/g, dw). For heavy metals, the mean concentrations of Pb, Cr, As, Cd were 399, 151, 48.13, and 5.85 mg/kg in indoor dust, respectively, and were 328, 191, 17.59, and 4.07 mg/kg in outdoor dust, respectively. Except for As, concentrations of TBBPA and other metals decreased with the increased distance away from the e-waste recycling center, suggesting significant contribution of e-waste activities. The daily exposure doses of TBBPA ranged from 0.04 to 7.50 ng/kg-bw/day for adults and from 0.31 to 58.54 ng/kg-bw/day for children, representing the highest values reported to date for TBBPA exposure via dust ingestion. Daily exposure doses of Cr, As, and Cd were all below the reference doses. However, daily exposure dose of Pb for children in areas near the e-waste processing center was above the reference dose, posing significant health concern for children in that region. Copyright © 2015 Elsevier B.V. All rights reserved.

  16. Degradation of organic pollutants by Ag, Cu and Sn doped waste non-metallic printed circuit boards.

    Science.gov (United States)

    Ramaswamy, Kadari; Radha, Velchuri; Malathi, M; Vithal, Muga; Munirathnam, Nagegownivari R

    2017-02-01

    The disposal and reuse of waste printed circuit boards have been the major global concerns. Printed circuit boards, a form of Electronic waste (hereafter e-waste), have been chemically processed, doped with Ag+, Cu2+ and Sn2+, and used as visible light photocatalysts against the degradation of methylene blue and methyl violet. The elemental analyses of pristine and metal doped printed circuit board were obtained using energy dispersive X-ray fluorescence (EDXRF) spectra and inductively coupled plasma optical emission spectroscopy (ICP-OES). The morphology of parent and doped printed circuit board was obtained from scanning electron microscopy (SEM) measurements. The photocatalytic activity of parent and metal doped samples was carried out for the decomposition of organic pollutants, methylene blue and methyl violet, under visible light irradiation. Metal doped waste printed circuit boards (WPCBs) have shown higher photocatalytic activity against the degradation of methyl violet and methylene blue under visible light irradiation. Scavenger experiments were performed to identify the reactive intermediates responsible for the degradation of methylene blue and methyl violet. The reactive species responsible for the degradation of MV and MB were found to be holes and hydroxyl radicals. A possible mechanism of degradation of methylene blue and methyl violet is given. The stability and reusability of the catalysts are also investigated. Copyright © 2016. Published by Elsevier Ltd.

  17. A practical approach for solving disposal of rubber waste: Leachability of heavy metals from foamed concrete containing rubber powder waste (RPW)

    Science.gov (United States)

    Kadir, Aeslina Abdul; Hassan, Mohd Ikhmal Haqeem; Sarani, Noor Amira; Yatim, Fatin Syahirah Mohamed; Jaini, Zainorizuan Mohd

    2017-09-01

    Enormous disposal of rubber wastes has become an issue with the facts that all tires have its own life span. Inefficient disposal method of RPW from used tire can cause environmental impact as the heavy metals content in tire can easily leach out thus causing contamination to the soil and waterways. The goals of this study is to identify the heavy metals content of rubber powder waste (RPW) and to determine the potential of leachability of heavy metals from foamed concrete containing different percentages of RPW. Therefore, this study is focused on the leachability of RPW incorporated in foamed concrete. Different percentages of RPW were incorporated in foamed concrete (0%, 6%, 12% and 18%) for the investigation. Leachability tests were done by using toxicity characteristic leaching procedure (TCLP) on crushed samples of foamed concrete incorporated with RPW and were analyzed by using inductive coupled plasma mass spectrometry (ICP-MS). The results from XRF indicated that RPW is high in metals such as Zn, Cu, Ba and Co. The highest concentration of heavy metals in raw RPW is Zn with 51403 ppm which is exceeded USEPA (2010) maximum contaminant level (MCL) of Zn with only 5 ppm. After RPW had been incorporated into a foamed concrete, the results demonstrated that the Zn, Cu, Ba and Co heavy metals were less leached and complied with USEPA standard. The incorporation of RPW into foamed concrete in this study demonstrated that it could be a potential alternative raw material for concrete thus enhancing the possibility of its reuse in safe and sustainable way.

  18. Mathematical modeling of the emission of heavy metals into water bodies from building materials derived from production waste

    Directory of Open Access Journals (Sweden)

    Pugin Konstantin Georgievich

    2016-01-01

    Full Text Available At the present time industrial waste is considered to be an alternative to primary natural resources when producing construction materials and products. The use of industrial waste in the construction branch allows reducing ecological load on the environment and population as a result of reducing the amount of unrecyclable waste and reducing the use of primary natural resources. Though when involving waste products as raw material in the preparation of building materials there occur environmental risks of anthropogenic impact increase on the environment. These risks are related to possible emission of heavy metals from construction materials in use. The article describes a tool which allows predicting this issue, depending on the acidity of the medium, the residence time of the material in the environment. The experimental data obtained in determining the migration activity of metals from cement concretes to aqueous solutions served as the basis for the mathematical model. The proposed model allows us to make a prediction of anthropogenic impact on the environment and commensurate this impact with the possibility of assimilation of the environment area where the building materials are applied. This will allow conducting an effective assessment of the created and applied technologies of waste disposal, taking into account the operating conditions of the materials produced.

  19. Waste management of printed wiring boards: a life cycle assessment of the metals recycling chain from liberation through refining.

    Science.gov (United States)

    Xue, Mianqiang; Kendall, Alissa; Xu, Zhenming; Schoenung, Julie M

    2015-01-20

    Due to economic and societal reasons, informal activities including open burning, backyard recycling, and landfill are still the prevailing methods used for electronic waste treatment in developing countries. Great efforts have been made, especially in China, to promote formal approaches for electronic waste management by enacting laws, developing green recycling technologies, initiating pilot programs, etc. The formal recycling process can, however, engender environmental impact and resource consumption, although information on the environmental loads and resource consumption is currently limited. To quantitatively assess the environmental impact of the processes in a formal printed wiring board (PWB) recycling chain, life cycle assessment (LCA) was applied to a formal recycling chain that includes the steps from waste liberation through materials refining. The metal leaching in the refining stage was identified as a critical process, posing most of the environmental impact in the recycling chain. Global warming potential was the most significant environmental impact category after normalization and weighting, followed by fossil abiotic depletion potential, and marine aquatic eco-toxicity potential. Scenario modeling results showed that variations in the power source and chemical reagents consumption had the greatest influence on the environmental performance. The environmental impact from transportation used for PWB collection was also evaluated. The results were further compared to conventional primary metals production processes, highlighting the environmental benefit of metal recycling from waste PWBs. Optimizing the collection mode, increasing the precious metals recovery efficiency in the beneficiation stage and decreasing the chemical reagents consumption in the refining stage by effective materials liberation and separation are proposed as potential improvement strategies to make the recycling chain more environmentally friendly. The LCA results provide

  20. Reduction of heavy metals in residues from the dismantling of waste electrical and electronic equipment before incineration.

    Science.gov (United States)

    Long, Yu-Yang; Feng, Yi-Jian; Cai, Si-Shi; Hu, Li-Fang; Shen, Dong-Sheng

    2014-05-15

    Residues disposal from the dismantling of waste electrical and electronic equipment are challenging because of the large waste volumes, degradation-resistance, low density and high heavy metal content. Incineration is advantageous for treating these residues but high heavy metal contents may exist in incinerator input and output streams. We have developed and studied a specialized heavy metal reduction process, which includes sieving and washing for treating residues before incineration. The preferable screen aperture for sieving was found to be 2.36mm (8 meshes) in this study; using this screen aperture resulted in the removal of approximately 47.2% Cu, 65.9% Zn, 26.5% Pb, 55.4% Ni and 58.8% Cd from the residues. Subsequent washing further reduces the heavy metal content in the residues larger than 2.36mm, with preferable conditions being 400rpm rotation speed, 5min washing duration and liquid-to-solid ratio of 25:1. The highest cumulative removal efficiencies of Cu, Zn, Pb, Ni and Cd after sieving and washing reached 81.1%, 61.4%, 75.8%, 97.2% and 72.7%, respectively. The combined sieving and washing process is environmentally friendly, can be used for the removal of heavy metals from the residues and has benefits in terms of heavy metal recycling. Copyright © 2014 Elsevier B.V. All rights reserved.

  1. SURVEY OF HEAVY METALS CONCENTRATION IN MUNICIPAL SOLID WASTES LEACHATE OF ISFAHAN CITY AND THEIR REDUCTION METHOD

    Directory of Open Access Journals (Sweden)

    A.A.R PARVARESH

    2001-12-01

    Full Text Available Introduction In duration steps of collection, transfer and disposal of solid wastes and also change of solid wastes to compost, produced leachate includes various pollutants such as heavy metals. The amounts of heavy metals don"t easily degrate in environment and would be concentrated in food chain and caused many problems for environment and human. Thus, the goal of present research is to investigation of heavy metals concentration in municipal solid wastes leachate of Isfahan city and reduction method for this case. Methods. leachate from four transfer station and composting plant was sampled ten times and in the first stage, quality of samples was evaluated from pH, COD, total solids (TS, total volatile solids (TYS, total fixed solids (TFS and heavy metals such as Cadmium, Chromium, Zinc, Copper and Nickel viewpoints. Chemical coagulants such as lime, alum and ferric chloride were applied using the Jar test to reduce heavy metals concentration. Results. The results revealed that mean concentration of heavy metals Cd, Cr. Zn Cu and Ni in leachate was equal to 0.63, 1.22, 7.42, 2.15 and 2.22 mg/l respectively and also the results of statistical analysis (ANOVA showed no significant difference between heavy metals concentration in various stations (P > 0.05. The results of Jar test revealed that optimum pH for chemical precipitation, and also optimum concentration of the three coagulants were 2400, 1400 and 1000 mg/l respectively. Discussion. Under this study elements concentration of leachate as compared with effluent standard (Environmental Protection Agency were exceeded the limits. Alum with 75-95 percent removal has the highest effciency as compared to other coagulants, lime with 70-88 percent removal and ferric chloride with 65-85 percent removal are in next order. Erom economical aspect, lime is cost benefit, ferric chloride and alum are in raked next respectively.

  2. PROCESS FOR SEPARATING PLUTONIUM BY REPEATED PRECIPITATION WITH AMPHOTERIC HYDROXIDE CARRIERS

    Science.gov (United States)

    Faris, B.F.

    1960-04-01

    A multiple carrier precipitation method is described for separating and recovering plutonium from an aqueous solution. The hydroxide of an amphoteric metal is precipitated in an aqueous plutonium-containing solution. This precipitate, which carries plutonium, is then separated from the supernatant liquid and dissolved in an aqueous hydroxide solution, forming a second plutonium- containing solution. lons of an amphoteric metal which forms an insoluble hydroxide under the conditions existing in this second solution are added to the second solution. The precipitate which forms and which carries plutonium is separated from the supernatant liquid. Amphoteric metals which may be employed are aluminum, bibmuth, copper, cobalt, iron, lanthanum, nickel, and zirconium.

  3. Exposure to atmospheric pms, pahs, pcdd/fs and metals near an open air waste burning site in Beirut

    Directory of Open Access Journals (Sweden)

    Rima Baalbaki

    2016-12-01

    Full Text Available Baalbaki, R., El Hage, R., Nassar, J., Gerard, J., Saliba, N.B., Zaarour, R., Abboud, M., Wehbeh, F., Khalaf, L.K., Shihadeh, A.L., Saliba, N.A. 2016. Exposure to atmospheric PMS, PAHS, PCDD/FS and metals near an open air waste burning site in Beirut. Lebanese Science Journal, 17(2: 91-103. Since July 2015, Lebanon has experienced the worst solid waste management crisis in its history. Consequently, open-air waste burning in the vicinity of highly populated areas in Beirut has become a common practice. This study evaluates the effects of open-air dumping and burning on local air quality and public health. The levels of particulate matter (PM10, PM2.5, gaseous and particle-bound polycyclic aromatic hydrocarbons (PAHs, polychlorinated dibenzo-dioxins and furans (PCDD/Fs, and particle-bound metals at a residence close to waste burning are reported. Concentrations, determined between October 2 and December 2, 2015, were compared either to previous measurements or to measurements taken away from a nearby burning incident, and after it had rained. Subsequently, the cancer risk due to exposure to these chemicals was assessed. Results showed alarming increases in pollutant concentrations which was translated into an increase in short-term cancer risk from about 1 to 20 people per million on the days when waste was being burned. Findings were shared with the public to warn the community against the dangers of waste mismanagement, and underline the obvious need for solid waste management at the governmental and municipal levels.

  4. AN INITIAL ASSESSMENT OF POTENTIAL PRODUCTION TECHNOLOGIES FOR EPSILON-METAL WASTE FORMS

    Energy Technology Data Exchange (ETDEWEB)

    Rohatgi, Aashish; Strachan, Denis M.

    2011-03-01

    This report examines and ranks a total of seven materials processing techniques that may be potentially utilized to consolidate the undissolved solids from nuclear fuel reprocessing into a low-surface area form. Commercial vendors of processing equipment were contacted and literature researched to gather information for this report. Typical equipment and their operation, corresponding to each of the seven techniques, are described in the report based upon the discussions and information provided by the vendors. Although the report does not purport to describe all the capabilities and issues of various consolidation techniques, it is anticipated that this report will serve as a guide by highlighting the key advantages and disadvantages of these techniques. The processing techniques described in this report were broadly classified into those that employed melting and solidification, and those in which the consolidation takes place in the solid-state. Four additional techniques were examined that were deemed impractical, but were included for completeness. The techniques were ranked based on criteria such as flexibility in accepting wide-variety of feed-stock (chemistry, form, and quantity), ease of long-term maintenance, hot cell space requirements, generation of additional waste streams, cost, and any special considerations. Based on the assumption of ~2.5 L of waste to be consolidated per day, sintering based techniques, namely, microwave sintering, spark plasma sintering and hot isostatic pressing, were ranked as the top-3 choices, respectively. Melting and solidification based techniques were ranked lower on account of generation of volatile phases and difficulties associated with reactivity and containment of the molten metal.

  5. Hierarchical Cobalt Hydroxide and B/N Co-Doped Graphene Nanohybrids Derived from Metal-Organic Frameworks for High Energy Density Asymmetric Supercapacitors

    Science.gov (United States)

    Tabassum, Hassina; Mahmood, Asif; Wang, Qingfei; Xia, Wei; Liang, Zibin; Qiu, Bin; zhao, Ruo; Zou, Ruqiang

    2017-01-01

    To cater for the demands of electrochemical energy storage system, the development of cost effective, durable and highly efficient electrode materials is desired. Here, a novel electrode material based on redox active β-Co(OH)2 and B, N co-doped graphene nanohybrid is presented for electrochemical supercapacitor by employing a facile metal-organic frameworks (MOFs) route through pyrolysis and hydrothermal treatment. The Co(OH)2 could be firmly stabilized by dual protection of N-doped carbon polyhedron (CP) and B/N co-doped graphene (BCN) nanosheets. Interestingly, the porous carbon and BCN nanosheets greatly improve the charge storage, wettability, and redox activity of electrodes. Thus the hybrid delivers specific capacitance of 1263 F g−1 at a current density of 1A g−1 with 90% capacitance retention over 5000 cycles. Furthermore, the new aqueous asymmetric supercapacitor (ASC) was also designed by using Co(OH)2@CP@BCN nanohybrid and BCN nanosheets as positive and negative electrodes respectively, which leads to high energy density of 20.25 Whkg−1. This device also exhibits excellent rate capability with energy density of 15.55 Whkg−1 at power density of 9331 Wkg−1 coupled long termed stability up to 6000 cycles. PMID:28240224

  6. Impact of spreading olive mill waste water on agricultural soils for leaching of metal micronutrients and cations.

    Science.gov (United States)

    Aharonov-Nadborny, R; Tsechansky, L; Raviv, M; Graber, E R

    2017-07-01

    Olive mill waste water (OMWW) is an acidic (pH 4-5), saline (EC ∼ 5-10 mS cm -1 ), blackish-red aqueous byproduct of the three phase olive oil production process, with a high chemical oxygen demand (COD) of up to 220,000 mg L -1 . OMWW is conventionally disposed of by uncontrolled dumping into the environment or by semi-controlled spreading on agricultural soils. It was hypothesized that spreading such liquids on agricultural soils could result in the release and mobilization of indigenous soil metals. The effect of OMWW spreading on leaching of metal cations (Na, K, Mg, Mn, Fe, Cu, Zn) was tested in four non-contaminated agricultural soils having different textures (sand, clay loam, clay, and loam) and chemical properties. While the OMWW contributed metals to the soil solution, it also mobilized indigenous soil metals as a function of soil clay content, cation exchange capacity (CEC), and soil pH-buffer capacity. Leaching of soil-originated metals from the sandy soil was substantially greater than from the loam and clay soils, while the clay loam was enriched with metals derived from the OMWW. These trends were attributed to cation exchange and organic-metal complex formation. The organic matter fraction of OMWW forms complexes with metal cations; these complexes may be mobile or precipitate, depending on the soil chemical and physical environment. Copyright © 2017 Elsevier Ltd. All rights reserved.

  7. Influence of biochar on heavy metals and microbial community during composting of river sediment with agricultural wastes.

    Science.gov (United States)

    Chen, Yaoning; Liu, Yao; Li, Yuanping; Wu, Yanxin; Chen, Yanrong; Zeng, Guangming; Zhang, Jiachao; Li, Hui

    2017-11-01

    Studies were performed to evaluate influence of biochar addition on physico-chemical process, heavy metals transformation and bacterial community diversity during composting of sediment with agricultural wastes. Simultaneously, the relationships between those parameters including heavy metals and bacterial community compositions were evaluated by redundancy analysis (RDA). The results show that the extraction efficiency of DTPA extractable heavy metals decreased in both piles, and reduced more in pile with biochar addition about 0.1-2.96%. Biochar addition dramatically influenced the bacterial community structure during the composting process. Moreover, the bacterial community composition was significantly correlated with C/N ratio, water soluble carbon (WSC), and organic matter (OM) (Pheavy metals contamination. Copyright © 2017 Elsevier Ltd. All rights reserved.

  8. Leachability of Heavy Metals from Lightweight Aggregates Made with Sewage Sludge and Municipal Solid Waste Incineration Fly Ash

    Science.gov (United States)

    Wei, Na

    2015-01-01

    Lightweight aggregate (LWA) production with sewage sludge and municipal solid waste incineration (MSWI) fly ash is an effective approach for waste disposal. This study investigated the stability of heavy metals in LWA made from sewage sludge and MSWI fly ash. Leaching tests were conducted to find out the effects of MSWI fly ash/sewage sludge (MSWI FA/SS) ratio, sintering temperature and sintering time. It was found that with the increase of MSWI FA/SS ratio, leaching rates of all heavy metals firstly decreased and then increased, indicating the optimal ratio of MSWI fly ash/sewage sludge was 2:8. With the increase of sintering temperature and sintering time, the heavy metal solidifying efficiencies were strongly enhanced by crystallization and chemical incorporations within the aluminosilicate or silicate frameworks during the sintering process. However, taking cost-savings and lower energy consumption into account, 1100 °C and 8 min were selected as the optimal parameters for LWA sample- containing sludge production. Furthermore, heavy metal leaching concentrations under these optimal LWA production parameters were found to be in the range of China’s regulatory requirements. It is concluded that heavy metals can be properly stabilized in LWA samples containing sludge and cannot be easily released into the environment again to cause secondary pollution. PMID:25961800

  9. Production of biochar from olive mill solid waste for heavy metal removal.

    Science.gov (United States)

    Abdelhadi, Samya O; Dosoretz, Carlos G; Rytwo, Giora; Gerchman, Yoram; Azaizeh, Hassan

    2017-11-01

    Commercial activated carbon (CAC) and biochar are useful adsorbents for removing heavy metals (HM) from water, but their production is costly. Biochar production from olive solid waste from two olive cultivars (Picual and Souri) and two oil production process (two- or three-phase) and two temperatures (350 and 450°C) was tested. The biochar yield was 24-35% of the biomass, with a surface area of 1.65-8.12m(2)g(-1), as compared to 1100m(2)g(-1) for CAC. Picual residue from the two-phase milling technique, pyrolysed at 350°C, had the best cumulative removal capacity for Cu(+2), Pb(+2), Cd(+2), Ni(+2) and Zn(+2) with more than 85% compared to other biochar types and CAC. These results suggest that surface area cannot be used as a sole predictor of HM removal capacity. FTIR analysis revealed the presence of different functional groups in the different biochar types, which may be related to the differences in absorbing capacities. Copyright © 2017 Elsevier Ltd. All rights reserved.

  10. Valorization of agricultural waste into activated carbons and its adsorption characteristics for heavy metals

    Science.gov (United States)

    Koubaissy, Bachar; Toufaily, Joumana; Cheikh, Safaa; Hassan, Malak; Hamieh, Tayssir

    2014-03-01

    Activated carbon derived from pine cones waste was prepared by carbonization at 450°C, activated by different activating agents: ZnCl 2, H 2 SO 4 and NaOH, and then pyrolyzed at 600°C. Adsorption of Cr VI and other heavy metals (Mn II, Fe II, Cu II) on activated carbons was investigated to evaluate the adsorption properties. Special attention was paid to the effects of carbon surface functionalities that were analyzed by FT-IR and zeta potential study. Moreover, XRD study of activated carbon was also carried out. Results had shown that activated carbon by NaOH was the best adsorbent for removal of chromium VI from wastewater. The solid-solution interaction was determined by analyzing the adsorption isotherms at room temperature at different pH. When pH is above 4, the removal fraction of Cr (VI) ions decreased with the increase of pH. The removal fraction of Cr (VI) ions decreased below pH 4. The preferable removal of Cu (II) over Mn(II) and Fe (II) could be due to its lower affinity to solvent.Pseudo-second order equation provided the better correlation for the adsorption kinetics data. Equilibrium isotherms were determined by Fowler-Guggenheim model.

  11. Process for removing and detoxifying cadmium from scrap metal including mixed waste

    Energy Technology Data Exchange (ETDEWEB)

    Kronberg, J.W.

    1994-07-01

    Cadmium-bearing scrap from nuclear applications, such as neutron shielding and reactor control and safety rods, must usually be handled as mixed waste since it is radioactive and the cadmium in it is both leachable and highly toxic. Removing the cadmium from this scrap, and converting it to a nonleachable and minimally radioactive form, would greatly simplify disposal or recycling. A process now under development will do this by shredding the scrap; leaching it with reagents which selectively dissolve out the cadmium; reprecipitating the cadmium as its highly insoluble sulfide; then fusing the sulfide into a glassy matrix to bring its leachability below EPA limits before disposal. Alternatively, the cadmium may be recovered for reuse. A particular advantage of the process is that all reagents (except the glass frit) can easily be recovered and reused in a nearly closed cycle, minimizing the risk of radioactive release. The process does not harm common metals such as aluminum, iron and stainless steel, and is also applicable to non-nuclear cadmium-bearing scrap such as nickel-cadmium batteries.

  12. Layered double hydroxides

    DEFF Research Database (Denmark)

    López Rayo, Sandra; Imran, Ahmad; Hansen, Hans Chr. Bruun

    2017-01-01

    A novel zinc (Zn) fertilizer concept based on Zn doped layered double hydroxides (Zn-doped Mg-Fe-LDHs) has been investigated. Zn-doped Mg-Fe-LDHs were synthetized, their chemical composition was analyzed and their nutrient release was studied in buffered solutions with different pH values. Uptake...... of Zn by barley (Hordeum vulgare cv. Antonia) was evaluated in short- (8 weeks), medium- (11 weeks) and long-term (28 weeks) experiments in quartz sand and in a calcareous soil enriched with Zn-doped Mg-Fe-LDHs. The Zn release rate of the Zn-doped Mg-Fe-LDHs was described by a first-order kinetics...

  13. Interaction of pristine hydrotalcite-like layered double hydroxides ...

    Indian Academy of Sciences (India)

    Metal oxides in general have surface acidic sites, but for exceptional circumstances, are not expected to mineralize CO2. Given their intrinsic basicity and an expandable interlayer gallery, the hydrotalcite-like layered double hydroxides (LDHs) are expected to be superior candidate materials for CO2 mineralization.

  14. Interaction of pristine hydrotalcite-like layered double hydroxides ...

    Indian Academy of Sciences (India)

    Abstract. Metal oxides in general have surface acidic sites, but for exceptional circumstances, are not expected to mineralize CO2. Given their intrinsic basicity and an expandable interlayer gallery, the hydrotalcite-like layered double hydroxides (LDHs) are expected to be superior candidate materials for CO2 mineralization.

  15. Recovery of Metallic Values from Brass Waste Using Brønsted Acidic Ionic Liquid as Leachate

    Science.gov (United States)

    Kilicarslan, Ayfer; Saridede, Muhlis Nezihi

    2015-11-01

    The waste formed during industrial brass manufacturing is rich in copper and zinc metals. Therefore, treatment of this waste is a necessity from economic and environmental aspects. This study presents a process for recovery of zinc and copper through Brønsted ionic liquid (1-butyl-3-methyl-imidazolium hydrogen sulfate; [Bmim]HSO4), as leachate. It was found that all zinc content could be dissolved from the waste under two optimum conditions: (1) in ionic liquid (IL) concentration of 70% (v/v) at 60°C in 30 min or (2) in IL concentration of 50% (v/v) at 100°C in 60 min. On the other hand, ionic liquid leaching gave poor copper solubility under the conditions of the study. Zinc dissolution in the range 5-75 min by [Bmim]HSO4 can be explained with the shrinking core model controlled by diffusion through a product layer, and the apparent activation energy was calculated as 4.36 kJ/mol. The leach liquor was treated to obtain metallic zinc by the electrowinning method without a purification step. Scanning electron microscopy/energy dispersive x-ray spectroscopy (SEM/EDX) investigations showed that the layer of metallic zinc was plated successfully on the cathode.

  16. Electrochemical treatment of liquid wastes

    Energy Technology Data Exchange (ETDEWEB)

    Hobbs, D.T. [Savannah River Technology Center, Aiken, SC (United States)

    1997-10-01

    Under this task, electrochemical treatment processes are being evaluated and developed for the destruction of organic compounds and nitrates/nitrites and the removal of other hazardous species from liquid wastes stored throughout the DOE complex. This technology targets the (1) destruction of nitrates, nitrites and organic compounds; (2) removal of radionuclides; and (3) removal of RCRA metals. The development program consists of five major tasks: (1) evaluation of electrochemical reactors for the destruction and removal of hazardous waste components, (2) development and validation of engineering process models, (3) radioactive laboratory-scale tests, (4) demonstration of the technology in an engineering-scale reactor, and (5) analysis and evaluation of test data. The development program team is comprised of individuals from national laboratories, academic institutions, and private industry. Possible benefits of this technology include: (1) improved radionuclide separation as a result of the removal of organic complexants, (2) reduction in the concentrations of hazardous and radioactive species in the waste (e.g., removal of nitrate, mercury, chromium, cadmium, {sup 99}Tc, and {sup 106}Ru), (3) reduction in the size of the off-gas handling equipment for the vitrification of low-level waste (LLW) by reducing the source of NO{sub x} emissions, (4) recovery of chemicals of value (e.g. sodium hydroxide), and (5) reduction in the volume of waste requiring disposal.

  17. Systematic review of potential health risks posed by pharmaceutical, occupational and consumer exposures to metallic and nanoscale aluminum, aluminum oxides, aluminum hydroxide and its soluble salts

    Science.gov (United States)

    Willhite, Calvin C.; Karyakina, Nataliya A.; Yokel, Robert A.; Yenugadhati, Nagarajkumar; Wisniewski, Thomas M.; Arnold, Ian M. F.; Momoli, Franco; Krewski, Daniel

    2016-01-01

    leads to intrinsic apoptosis. In contrast, the toxicity of the insoluble Al oxides depends primarily on their behavior as particulates. Aluminum has been held responsible for human morbidity and mortality, but there is no consistent and convincing evidence to associate the Al found in food and drinking water at the doses and chemical forms presently consumed by people living in North America and Western Europe with increased risk for Alzheimer’s disease (AD). Neither is there clear evidence to show use of Al-containing underarm antiperspirants or cosmetics increases the risk of AD or breast cancer. Metallic Al, its oxides, and common Al salts have not been shown to be either genotoxic or carcinogenic. Aluminum exposures during neonatal and pediatric parenteral nutrition (PN) can impair bone mineralization and delay neurological development. Adverse effects to vaccines with Al adjuvants have occurred; however, recent controlled trials found that the immunologic response to certain vaccines with Al adjuvants was no greater, and in some cases less than, that after identical vaccination without Al adjuvants. The scientific literature on the adverse health effects of Al is extensive. Health risk assessments for Al must take into account individual co-factors (e.g., age, renal function, diet, gastric pH). Conclusions from the current review point to the need for refinement of the PTWI, reduction of Al contamination in PN solutions, justification for routine addition of Al to vaccines, and harmonization of OELs for Al substances. PMID:25233067

  18. Systematic review of potential health risks posed by pharmaceutical, occupational and consumer exposures to metallic and nanoscale aluminum, aluminum oxides, aluminum hydroxide and its soluble salts.

    Science.gov (United States)

    Willhite, Calvin C; Karyakina, Nataliya A; Yokel, Robert A; Yenugadhati, Nagarajkumar; Wisniewski, Thomas M; Arnold, Ian M F; Momoli, Franco; Krewski, Daniel

    2014-10-01

    oxidative damage that leads to intrinsic apoptosis. In contrast, the toxicity of the insoluble Al oxides depends primarily on their behavior as particulates. Aluminum has been held responsible for human morbidity and mortality, but there is no consistent and convincing evidence to associate the Al found in food and drinking water at the doses and chemical forms presently consumed by people living in North America and Western Europe with increased risk for Alzheimer's disease (AD). Neither is there clear evidence to show use of Al-containing underarm antiperspirants or cosmetics increases the risk of AD or breast cancer. Metallic Al, its oxides, and common Al salts have not been shown to be either genotoxic or carcinogenic. Aluminum exposures during neonatal and pediatric parenteral nutrition (PN) can impair bone mineralization and delay neurological development. Adverse effects to vaccines with Al adjuvants have occurred; however, recent controlled trials found that the immunologic response to certain vaccines with Al adjuvants was no greater, and in some cases less than, that after identical vaccination without Al adjuvants. The scientific literature on the adverse health effects of Al is extensive. Health risk assessments for Al must take into account individual co-factors (e.g., age, renal function, diet, gastric pH). Conclusions from the current review point to the need for refinement of the PTWI, reduction of Al contamination in PN solutions, justification for routine addition of Al to vaccines, and harmonization of OELs for Al substances.

  19. The Effects of Organic Wastes on Soil and Cotton Quality with respect to the Risk of Boron and Heavy Metal Pollution

    OpenAIRE

    Seçer, Müzeyyen; Elmaci, Ömer Lütfü; Ceylan, Şafak

    2016-01-01

    The effects on soil and cotton quality of organic wastes from medicinal and aromatic plant factories were investigated with regard to the risks of boron and heavy metal pollution. Oily cumin, oregano, oilless oregano wastes, and mineral fertilizers were applied to cotton in two field experiments performed in the years 2003 and 2006. The Pb content of the soil differed significantly in the 2003 experiment and oregano wastes had significantly decreasing effect. Boron of soil to which oily cumin...

  20. Heavy metal removal and recovery using microorganisms

    Energy Technology Data Exchange (ETDEWEB)

    Wilde, E.W. (Westinghouse Savannah River Co., Aiken, SC (United States)); Benemann, J.R. (Benemann (J.R.), Pinole, CA (United States))

    1991-02-01

    Microorganisms -- bacteria, fungi, and microalgae -- can accumulate relatively large amounts of toxic heavy metals and radionuclides from the environment. These organisms often exhibit specificity for particular metals. The metal content of microbial biomass can be a substantial fraction of total dry weight with concentration factors (metal in dry biomass to metal in solution) exceeding one million in some cases. Both living and inert (dead) microbial biomass can be used to reduce heavy metal concentrations in contaminated waters to very low levels -- parts per billion and even lower. In many respects (e.g. specificity, residual metal concentrations, accumulation factors, and economics) microbial bioremoval processes can be superior to conventional processes, such as ion exchange and caustic (lime or hydroxide) precipitation for heavy metals removal from waste and contaminated waters. Thus, bioremoval could be developed to contribute to the clean-up of wastes at the Savannah River Site (SRS) and other DOE facilities. However, the potential advantages of bioremoval processes must still be developed into practical operating systems. A detailed review of the literature suggests that appropriate bioremoval processes could be developed for the SRS. There is great variability from one biomass source to another in bioremoval capabilities. Bioremoval is affected by pH, other ions, temperature, and many other factors. The biological (living vs. dead) and physical (immobilized vs. dispersed) characteristics of the biomass also greatly affect metal binding. Even subtle differences in the microbial biomass, such as the conditions under which it was cultivated, can have major effects on heavy metal binding.

  1. Chemical species of plutonium in Hanford radioactive tank waste

    Energy Technology Data Exchange (ETDEWEB)

    Barney, G.S.

    1997-10-22

    Large quantities of radioactive wastes have been generated at the Hanford Site over its operating life. The wastes with the highest activities are stored underground in 177 large (mostly one million gallon volume) concrete tanks with steel liners. The wastes contain processing chemicals, cladding chemicals, fission products, and actinides that were neutralized to a basic pH before addition to the tanks to prevent corrosion of the steel liners. Because the mission of the Hanford Site was to provide plutonium for defense purposes, the amount of plutonium lost to the wastes was relatively small. The best estimate of the amount of plutonium lost to all the waste tanks is about 500 kg. Given uncertainties in the measurements, some estimates are as high as 1,000 kg (Roetman et al. 1994). The wastes generally consist of (1) a sludge layer generated by precipitation of dissolved metals from aqueous wastes solutions during neutralization with sodium hydroxide, (2) a salt cake layer formed by crystallization of salts after evaporation of the supernate solution, and (3) an aqueous supernate solution that exists as a separate layer or as liquid contained in cavities between sludge or salt cake particles. The identity of chemical species of plutonium in these wastes will allow a better understanding of the behavior of the plutonium during storage in tanks, retrieval of the wastes, and processing of the wastes. Plutonium chemistry in the wastes is important to criticality and environmental concerns, and in processing the wastes for final disposal. Plutonium has been found to exist mainly in the sludge layers of the tanks along with other precipitated metal hydrous oxides. This is expected due to its low solubility in basic aqueous solutions. Tank supernate solutions do not contain high concentrations of plutonium even though some tanks contain high concentrations of complexing agents. The solutions also contain significant concentrations of hydroxide which competes with other

  2. Hanford Waste Physical and Rheological Properties: Data and Gaps

    Energy Technology Data Exchange (ETDEWEB)

    Wells, Beric E.; Kurath, Dean E.; Mahoney, Lenna A.; Onishi, Yasuo; Huckaby, James L.; Cooley, Scott K.; Burns, Carolyn A.; Buck, Edgar C.; Tingey, Joel M.; Daniel, Richard C.; Anderson, K. K.

    2011-08-01

    The Hanford Site in Washington State manages 177 underground storage tanks containing approximately 250,000 m3 of waste generated during past defense reprocessing and waste management operations. These tanks contain a mixture of sludge, saltcake and supernatant liquids. The insoluble sludge fraction of the waste consists of metal oxides and hydroxides and contains the bulk of many radionuclides such as the transuranic components and 90Sr. The saltcake, generated by extensive evaporation of aqueous solutions, consists primarily of dried sodium salts. The supernates consist of concentrated (5-15 M) aqueous solutions of sodium and potassium salts. The 177 storage tanks include 149 single-shell tanks (SSTs) and 28 double -hell tanks (DSTs). Ultimately the wastes need to be retrieved from the tanks for treatment and disposal. The SSTs contain minimal amounts of liquid wastes, and the Tank Operations Contractor is continuing a program of moving solid wastes from SSTs to interim storage in the DSTs. The Hanford DST system provides the staging location for waste feed delivery to the Department of Energy (DOE) Office of River Protection’s (ORP) Hanford Tank Waste Treatment and Immobilization Plant (WTP). The WTP is being designed and constructed to pretreat and then vitrify a large portion of the wastes in Hanford’s 177 underground waste storage tanks.

  3. Phosphate adsorption from sewage sludge filtrate using zinc-aluminum layered double hydroxides.

    Science.gov (United States)

    Cheng, Xiang; Huang, Xinrui; Wang, Xingzu; Zhao, Bingqing; Chen, Aiyan; Sun, Dezhi

    2009-09-30

    A series of layered double hydroxides (LDHs) with different metal cations were synthesized to remove phosphate in waste sludge filtrate from a municipal wastewater treatment plant for phosphorus recovery and to help control eutrophication. The highest phosphate adsorption capacity was obtained by using Zn-Al-2-300, that is LDHs with Zn/Al molar ratio of 2 and calcined at 300 degrees C for 4h. Circumneutral and mildly alkaline waters appeared suitable for the possible application of Zn-Al LDHs due to the amphoteric nature of aluminum hydroxide. Phosphate adsorption from the sludge filtrate by the LDHs followed pseudo-second-order kinetics, and the adsorption capacity at equilibrium was determined to be approximately 50 mg P/g. Adsorption isotherms showed that phosphate uptake in this study was an endothermic process and had a good fit with a Langmuir-type model. The absorbed phosphate can be effectively desorbed (more than 80%) from LDHs particles by a 5 wt% NaOH solution. The regeneration rate of used LDHs was approximately 60% after six cycles of adsorption-desorption-regeneration.

  4. Impact of metals in surface matrices from formal and informal electronic-waste recycling around Metro Manila, the Philippines, and intra-Asian comparison.

    Science.gov (United States)

    Fujimori, Takashi; Takigami, Hidetaka; Agusa, Tetsuro; Eguchi, Akifumi; Bekki, Kanae; Yoshida, Aya; Terazono, Atsushi; Ballesteros, Florencio C

    2012-06-30

    We report concentrations, enrichment factors, and hazard indicators of 11 metals (Ag, As, Cd, Co, Cu, Fe, In, Mn, Ni, Pb, and Zn) in soil and dust surface matrices from formal and informal electronic waste (e-waste) recycling sites around Metro Manila, the Philippines, referring to soil guidelines and previous data from various e-waste recycling sites in Asia. Surface dust from e-waste recycling sites had higher levels of metal contamination than surface soil. Comparison of formal and informal e-waste recycling sites (hereafter, "formal" and "informal") revealed differences in specific contaminants. Formal dust contained a mixture of serious pollutant metals (Ni, Cu, Pb, and Zn) and Cd (polluted modestly), quite high enrichment metals (Ag and In), and crust-derived metals (As, Co, Fe, and Mn). For informal soil, concentration levels of specific metals (Cd, Co, Cu, Mn, Ni, Pb, and Zn) were similar among Asian recycling sites. Formal dust had significantly higher hazardous risk than the other matrices (pmetals (Pb and Cu). There is also a high health risk for children ingesting surface matrices from informal e-waste recycling sites. Copyright © 2012 Elsevier B.V. All rights reserved.

  5. Heavy metals in hair of residents in an e-waste recycling area, south China: contents and assessment of bodily state.

    Science.gov (United States)

    Zheng, Jing; Luo, Xiao-Jun; Yuan, Jian-Gang; He, Luo-Yiyi; Zhou, Yi-Hui; Luo, Yong; Chen, She-Jun; Mai, Bi-Xian; Yang, Zhong-Yi

    2011-11-01

    Heavy metals were measured in hair from occupationally and nonoccupationally exposed populations in an e-waste recycling area and from residents from a control rural town. The levels of five heavy metals were in the following order of Zn > Pb, Cu > Cd > Ni, with the highest levels found in the occupationally exposed workers. The levels of Cd, Pb, and Cu were significantly higher in residents from the e-waste recycling area than in the control area. Elevated Cd, Pb, and Cu contents along with significant positive correlations between them in hair from the e-waste recycling area indicated that these metals were likely to have originated from the e-waste recycling activities. The similarity in heavy metal pattern between children and occupationally exposed workers indicated that children are particularly vulnerable to heavy metal pollution caused by e-waste recycling activities. The increased Cu exposure might be a benefit for the insufficient intake of Cu in the studied area. However, the elevated hair Cd and Pb levels implied that the residents in the e-waste area might be at high risk of toxic metal, especially for children and occupationally exposed workers.

  6. Geochemistry and mineralogy of arsenic in mine wastes and stream sediments in a historic metal mining area in the UK

    Energy Technology Data Exchange (ETDEWEB)

    Rieuwerts, J.S., E-mail: jrieuwerts@plymouth.ac.uk [School of Geography, Earth and Environmental Sciences, Plymouth University, Plymouth PL4 8AA (United Kingdom); Mighanetara, K.; Braungardt, C.B. [School of Geography, Earth and Environmental Sciences, Plymouth University, Plymouth PL4 8AA (United Kingdom); Rollinson, G.K. [Camborne School of Mines, CEMPS, University of Exeter, Tremough Campus, Penryn, Cornwall TR10 9EZ (United Kingdom); Pirrie, D. [Helford Geoscience LLP, Menallack Farm, Treverva, Penryn, Cornwall TR10 9BP (United Kingdom); Azizi, F. [School of Geography, Earth and Environmental Sciences, Plymouth University, Plymouth PL4 8AA (United Kingdom)

    2014-02-01

    Mining generates large amounts of waste which may contain potentially toxic elements (PTE), which, if released into the wider environment, can cause air, water and soil pollution long after mining operations have ceased. The fate and toxicological impact of PTEs are determined by their partitioning and speciation and in this study, the concentrations and mineralogy of arsenic in mine wastes and stream sediments in a former metal mining area of the UK are investigated. Pseudo-total (aqua-regia extractable) arsenic concentrations in all samples from the mining area exceeded background and guideline values by 1–5 orders of magnitude, with a maximum concentration in mine wastes of 1.8 × 10{sup 5} mg kg{sup −1} As and concentrations in stream sediments of up to 2.5 × 10{sup 4} mg kg{sup −1} As, raising concerns over potential environmental impacts. Mineralogical analysis of the wastes and sediments was undertaken by scanning electron microscopy (SEM) and automated SEM-EDS based quantitative evaluation (QEMSCAN®). The main arsenic mineral in the mine waste was scorodite and this was significantly correlated with pseudo-total As concentrations and significantly inversely correlated with potentially mobile arsenic, as estimated from the sum of exchangeable, reducible and oxidisable arsenic fractions obtained from a sequential extraction procedure; these findings correspond with the low solubility of scorodite in acidic mine wastes. The work presented shows that the study area remains grossly polluted by historical mining and processing and illustrates the value of combining mineralogical data with acid and sequential extractions to increase our understanding of potential environmental threats. - Highlights: • Stream sediments in a former mining area remain polluted with up to 25 g As per kg. • The main arsenic mineral in adjacent mine wastes appears to be scorodite. • Low solubility scorodite was inversely correlated with potentially mobile As. • Combining

  7. Application of supercritical water to decompose brominated epoxy resin and environmental friendly recovery of metals from waste memory module.

    Science.gov (United States)

    Li, Kuo; Xu, Zhenming

    2015-02-03

    Waste Memory Modules (WMMs), a particular kind of waste printed circuit board (WPCB), contain a high amount of brominated epoxy resin (BER), which may bring a series of environmental and health problems. On the other hand, metals like gold and copper are very valuable and are important to recover from WMMs. In the present study, an effective and environmental friendly method using supercritical water (SCW) to decompose BER and recover metals from WMMs was developed instead of hydrometallurgy or pyrometallurgy simultaneously. Experiments were conducted under external-catalyst-free conditions with temperatures ranging from 350 to 550 °C, pressures from 25 to 40 MPa, and reaction times from 120 to 360 min in a semibatch-type reactor. The results showed that BER could be quickly and efficiently decomposed under SCW condition, and the mechanism was possibly free radical reaction. After the SCW treatments, the glass fibers and metal foils in the solid residue could be easily liberated and recovered, respectively. The metal recovery rate reached 99.80%. The optimal parameters were determined as 495 °C, 33 MPa, and 305 min on the basis of response surface methodology (RSM). This study provides an efficient and environmental friendly approach for WMMs recycling compared with electrolysis, pyrometallurgy, and hydrometallurgy.

  8. Heavy metals distribution and risk assessment in soil from an informal E-waste recycling site in Lagos State, Nigeria.

    Science.gov (United States)

    Isimekhai, Khadijah A; Garelick, Hemda; Watt, John; Purchase, Diane

    2017-07-01

    Informal E-waste recycling can pose a risk to human health and the environment which this study endeavours to evaluate. The distribution of a number of heavy metals in soil from an informal recycling site in the largest market for used and new electronics and electrical equipment in West Africa was investigated. The potential bioavailability of heavy metals, extent of contamination, potential risk due to the recycling activities and impact of external factors such as rainfall were also assessed. The concentrations of all the heavy metals tested were higher in the area where burning of the waste occurred than at the control site, suggesting an impact of the recycling activities on the soil. The order of total metal concentrations was Cu > Pb > Zn > Mn > Ni > Sb > Cr > Cd for both the dry and wet seasons. The total concentrations of Cd, Cu, Mn, Ni and Zn were all significantly higher (p  Sb > Zn > Cu > Ni > Pb > Cr. When the risk was assessed using the Potential Ecological Risk Index (PERI), Cu was found to contribute the most to the potential ecological risk and Cd gave rise to the greatest concern due to its high toxic-response factor within the study site. Similarly, utilising the Risk Assessment Code (RAC) suggested that Cd posed the most risk in this site. This research establishes a high level of contamination in the study site and underscores the importance of applying the appropriate chemical speciation in risk assessment.

  9. Levels and ecological risk assessment of metals in soils from a typical e-waste recycling region in southeast China.

    Science.gov (United States)

    Zhao, Weituo; Ding, Lei; Gu, Xiaowen; Luo, Jie; Liu, Yunlang; Guo, Li; Shi, Yi; Huang, Ting; Cheng, Shenggao

    2015-11-01

    Due to the high threat to human health and the ecosystem from metals, the levels and distribution of As, Hg, Cr, Co, Ni, Cu, Zn, Cd, Pb, Mn, V, Sn, Sb, Li and Be in various layers of soil from an e-waste recycling area in Guiyu, China were investigated. The extent of pollution from the metals in soil was assessed using enrichment factors (EFs) and the Nemerow pollution index (P N ). To determine the metals' integrated potential ecological risks, the potential ecological risk index (RI) was chosen. The concentrations of Hg, Ni, Cu, Cd, Pb, Sn and Sb were mainly enriched in the topsoil. EF values (2-5) of the elements Hg, Co, Ni, Zn, Sn, Li and Be revealed their moderate enrichment status in the topsoil, derived from e-waste recycling activities. P N presented a decreasing trend in different layers in the order topsoil (0-20 cm) > deep soil (100-150 cm) > middle soil (50-100 cm) > shallow soil (20-50 cm). With higher potential ecological risk factor (E(i)), Hg and Cd are the main contributors to the potential ecological risk. With respect to the RI, all the values in soil from the study area exceeded 300, especially for the soil at sites S2, S4, S5, S7 and S8, where RI was greater than 600. Therefore, immediate remediation of the contaminated soil is necessary to prevent the release of metals and potential ecological harm.

  10. An analysis of the composition and metal contamination of plastics from waste electrical and electronic equipment (WEEE)

    Energy Technology Data Exchange (ETDEWEB)

    Stenvall, Erik, E-mail: erik.stenvall@chalmers.se [Department of Materials and Manufacturing Technology, Chalmers University of Technology, 41296 Göteborg (Sweden); Tostar, Sandra [Department of Industrial Materials Recycling, Chalmers University of Technology, 41296 Göteborg (Sweden); Boldizar, Antal [Department of Materials and Manufacturing Technology, Chalmers University of Technology, 41296 Göteborg (Sweden); Foreman, Mark R.StJ. [Department of Industrial Materials Recycling, Chalmers University of Technology, 41296 Göteborg (Sweden); Möller, Kenneth [Chemistry and Materials Technology, SP, 50115 Borås (Sweden)

    2013-04-15

    The compositions of three WEEE plastic batches of different origin were investigated using infrared spectroscopy, and the metal content was determined with inductively coupled plasma. The composition analysis of the plastics was based mainly on 14 samples collected from a real waste stream, and showed that the major constituents were high impact polystyrene (42 wt%), acrylonitrile–butadiene–styrene copolymer (38 wt%) and polypropylene (10 wt%). Their respective standard deviations were 21.4%, 16.5% and 60.7%, indicating a considerable variation even within a single batch. The level of metal particle contamination was found to be low in all samples, whereas wood contamination and rubber contamination were found to be about 1 wt% each in most samples. In the metal content analysis, iron was detected at levels up to 700 ppm in the recyclable waste plastics fraction, which is of concern due to its potential to catalyse redox reactions during melt processing and thus accelerate the degradation of plastics during recycling. Toxic metals were found only at very low concentrations, with the exception of lead and cadmium which could be detected at 200 ppm and 70 ppm levels, respectively, but these values are below the current threshold limits of 1000 ppm and 100 ppm set by the Restriction of Hazardous Substances directive.

  11. An analysis of the composition and metal contamination of plastics from waste electrical and electronic equipment (WEEE).

    Science.gov (United States)

    Stenvall, Erik; Tostar, Sandra; Boldizar, Antal; Foreman, Mark R StJ; Möller, Kenneth

    2013-04-01

    The compositions of three WEEE plastic batches of different origin were investigated using infrared spectroscopy, and the metal content was determined with inductively coupled plasma. The composition analysis of the plastics was based mainly on 14 samples collected from a real waste stream, and showed that the major constituents were high impact polystyrene (42 wt%), acrylonitrile-butadiene-styrene copolymer (38 wt%) and polypropylene (10 wt%). Their respective standard deviations were 21.4%, 16.5% and 60.7%, indicating a considerable variation even within a single batch. The level of metal particle contamination was found to be low in all samples, whereas wood contamination and rubber contamination were found to be about 1 wt% each in most samples. In the metal content analysis, iron was detected at levels up to 700 ppm in the recyclable waste plastics fraction, which is of concern due to its potential to catalyse redox reactions during melt processing and thus accelerate the degradation of plastics during recycling. Toxic metals were found only at very low concentrations, with the exception of lead and cadmium which could be detected at 200 ppm and 70 ppm levels, respectively, but these values are below the current threshold limits of 1000 ppm and 100 ppm set by the Restriction of Hazardous Substances directive. Copyright © 2013 Elsevier Ltd. All rights reserved.

  12. 21 CFR 184.1428 - Magnesium hydroxide.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Magnesium hydroxide. 184.1428 Section 184.1428 Food... Specific Substances Affirmed as GRAS § 184.1428 Magnesium hydroxide. (a) Magnesium hydroxide (Mg(OH)2, CAS... a white precipitate by the addition of sodium hydroxide to a water soluble magnesium salt or by...

  13. Pilot study on the internal exposure to heavy metals of informal-level electronic waste workers in Agbogbloshie, Accra, Ghana.

    Science.gov (United States)

    Wittsiepe, Jürgen; Feldt, Torsten; Till, Holger; Burchard, Gerd; Wilhelm, Michael; Fobil, Julius N

    2017-01-01

    Informal-level electronic waste (e-waste)-processing activities are performed at hotspots in developing countries such as India, China, and Ghana. These activities increase the ambient burden of heavy metals and contribute to the toxic exposure of the general population. However, few data exist on the internal exposure of populations involved in these informal activities and in close contact with fumes from the direct combustion of electronic waste products in these countries. Therefore, in a cross-sectional study design, we analyzed blood, urine, and hair samples from 75 e-waste workers residing in and/or working on a large e-waste recycling site in Agbogbloshie, Accra, Ghana, and compared the results against those of 40 individuals living in a suburb of Accra without direct exposure to e-waste recycling activities. A comparative analysis using the Mann-Whitney U test showed significantly higher median concentrations of blood lead (88.5 vs. 41.0 μg/l, p e-waste workers than those of controls. There was no difference in blood cadmium concentrations between the groups (0.51 vs. 0.57 μg/l, p = 0.215) or in urine mercury levels (0.18 vs. 0.18 μg/g crea , p = 0.820). Hair mercury levels were higher in the controls than in the e-waste workers (0.43 vs. 0.72, p compared our data with those from European populations, specifically using the German reference values, and found that the internal concentrations of the participants exceeded the German reference values in 59.3 vs. 3.1% (e-waste workers vs. controls) for blood lead, 56.9 vs. 52.5% for urine nickel, 22.2 vs. 20.0% for urine chromium, and 17.8 vs. 62.2% for hair mercury. In particular, the high blood lead levels of up to several hundred micrograms per liter are a cause for concern because many of the workers in Agbogbloshie are children or adolescents who are in developmental stages and are at a particular risk for negative health effects. We conclude that exposure to some of the heavy metals tended to

  14. Long-Term Experimental Determination of Solubilities of Micro-Crystalline Nd(III) Hydroxide in High Ionic Strength Solutions: Applications to Nuclear Waste Management [A Pitzer Model for Am(III)/Nd(III) hydroxide solubility in NaCl-H2O at 298.15 K to high ionic strengths: Experimental validation and model applications

    Energy Technology Data Exchange (ETDEWEB)

    Xiong, Yongliang [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States). Carlsbad Programs Group; Kirkes, Leslie Dawn [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States). Carlsbad Programs Group; Marrs, Cassandra [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States). Carlsbad Programs Group

    2017-12-01

    In this paper, the experimental results from long-term solubility experiments on micro crystalline neodymium hydroxide, Nd(OH)3(micro cr), in high ionic strength solutions at 298.15 K under well-constrained conditions are presented. The starting material was synthesized according to a well-established method in the literature. In contrast with the previous studies in which hydrogen ion concentrations in experiments were adjusted with addition of either an acid or a base, the hydrogen ion concentrations in our experiments are controlled by the dissolution of Nd(OH)3(micro cr), avoiding the possibility of phase change.

  15. Hydroxide catalysts for lignin depolymerization

    Energy Technology Data Exchange (ETDEWEB)

    Beckham, Gregg T.; Biddy, Mary J.; Chmely, Stephen C.; Sturgeon, Matthew

    2017-04-25

    Solid base catalysts and their use for the base-catalyzed depolymerization (BCD) of lignin to compounds such as aromatics are presented herein. Exemplary catalysts include layered double hydroxides (LDHs) as recyclable, heterogeneous catalysts for BCD of lignin.

  16. Hydroxide catalysts for lignin depolymerization

    Science.gov (United States)

    Beckham, Gregg T; Biddy, Mary J.; Kruger, Jacob S.; Chmely, Stephen C.; Sturgeon, Matthew

    2017-10-17

    Solid base catalysts and their use for the base-catalyzed depolymerization (BCD) of lignin to compounds such as aromatics are presented herein. Exemplary catalysts include layered double hydroxides (LDHs) as recyclable, heterogeneous catalysts for BCD of lignin.

  17. A study on the application of standards for clearance of metal waste generated during the decommissioning of NPP by using the RESRAD-RECYCLE

    Energy Technology Data Exchange (ETDEWEB)

    Song, Jong Soon; Kim, Dong Min; Lee, Sang Heon [Chosun University, Gwangju (Korea, Republic of)

    2016-12-15

    The metal waste generated during nuclear power plant decommissioning constitutes a large proportion of the total radioactive waste. This study investigates the current status of domestic and international regulatory requirements for clearance and the clearance experience of domestic institutions. The RESRAD-RECYCLE code was used for analyzing the clearance of the metal wastes generated during actual nuclear power plant decommissioning, and assessment of the exposure dose of twenty-six scenarios was carried out. The evaluation results will be useful in preliminary analysis of clearance and recycling during nuclear power plant decommissioning. As a next step, the effects of reducing disposal costs by clearance can be studied.

  18. [Heavy Metal Contamination in Farmland Soils at an E-waste Disassembling Site in Qingyuan, Guangdong, South China].

    Science.gov (United States)

    Zhang, Jin-lian; Ding, Jiang-feng; Lu, Gui-ning; Dang, Zhi; Yi, Xiao-yun

    2015-07-01

    Crude e-waste dismantling activities have caused a series of environmental pollution problems, and the pollutants released from the dismantling activities would finally pose high risks to human health by means of the accumulation through food chains. To explore the contamination status of heavy metals to the surrounding farmland soils in Longtang and Shijiao Town, Qingyuan, Guangdong, China, 22 farmland soil samples were collected and analyzed for the contents, spatial distributions and chemical forms of 6 heavy metals (Pb, Cu, Cd, Zn, Cr and Ni). The results showed that the 6 heavy metals exhibited obvious accumulations when compared to the corresponding background values in Guangdong Province. According to farmland environmental quality evaluation standard for edible agricultural products HJ 332-2006, the pollution severity of heavy metals was evaluated by monomial pollution index and Nemerow synthetic pollution index methods, the results indicated that 72. 7% of the soil samples contained one or more kinds of heavy metals with higher concentrations than the corresponding standard values, Cd, Cu, Pb and Zn were the main metals in the polluted soils, and for the proportion of contaminated soil samples in all the 22 samples, Cd was the highest, followed by Cu, and finally Pb and Zn. Nemerow synthetic pollution index further revealed that 68. 2% of soil samples were contaminated, and among them 53. 3% of samples were heavily contaminated. Most of the heavy metals were well correlated with each other at the 0. 05 or 0. 01 level, which indicated that primitive e-waste recycling activities were an important source of the heavy metal contamination in Longtang and Shijiao Town. The contents of Cd, Pb, Cu and Zn in surface soils were higher than those of other soil layers, and the contents of these 4 metals in deep soils (20- 100 cm) did not show significant decreases with the increasing depths. The contents of Cr and Ni maintained constant, and exhibited no statistical

  19. Partitioning characteristics and particle size distributions of heavy metals in the O{sub 2}/RFG waste incineration system

    Energy Technology Data Exchange (ETDEWEB)

    Chen, Jyh-Cherng, E-mail: jcchen@sunrise.hk.edu.tw [Department of Safety, Health and Environmental Engineering, HungKuang University, No. 34, Chung-Chie Rd., Shalu, Taichung County 43302, Taiwan (China); Huang, Jian-Sheng [Department of Safety, Health and Environmental Engineering, HungKuang University, No. 34, Chung-Chie Rd., Shalu, Taichung County 43302, Taiwan (China)

    2009-12-30

    This study applies the oxygen/recycled flue gas (O{sub 2}/RFG) combustion technology for waste incineration and investigates the effects of different RFG rates on the concentrations of gas pollutants as well as the partitioning characteristics and particle size distributions of five heavy metals (Cr, Cu, Pb, Zn, and Cd). Experimental results show that the combustion efficiency can be improved and the concentration of CO{sub 2} is increased by appropriately controlling the RFG rate in the O{sub 2}/RFG incineration system. The partitioning characteristics and size distributions of heavy metals in O{sub 2}/RFG combustion system are different from those in general air combustion system. Under O{sub 2}/RFG combustion system, the partitioning percentages of heavy metals in sand bed, bottom ash, and collected ash are increased. The particle size distributions of heavy metals display the triple-peak curves. As the RFG rate rises, the concentrations of volatile heavy metals are increased in small-size (<1 {mu}m) fly ash, decreased in medium-size (1-10 {mu}m) fly ash and increased in large-size (>10 {mu}m) fly ash. These phenomena will benefit to increase the overall control efficiency of heavy metals in the incineration system.

  20. The dispersal of metal mining wastes in the catchment of the river Geul (Belgium - The Netherlands)

    NARCIS (Netherlands)

    Leenaers, H.

    1989-01-01

    The metal mining industry has caused large quantities of heavy metals to enter countless river systems. The consequent spread of heavy metals is determined largely by how these metals bind with silt and soil particles and the transport pathways of these particles in the alluvial parts of river

  1. Accumulation and depuration of trace metals in Southern Toads, Bufo Terrestris, exposed to coal combustion waste

    Energy Technology Data Exchange (ETDEWEB)

    Ward, C.; Hassan, S.; Mendonca, M. [Auburn University, Auburn, AL (United States). Dept. of Biological Science

    2009-02-15

    Accumulation and depuration of metals by an organism are underrepresented in the literature. We collected southern toads (Bufo terrestris) from coal by-product (ash)-contaminated and uncontaminated sites to examine metal concentrations over time. Toads were placed in four exposure regimes, then sacrificed periodically over a 5-month period, and whole-body metal levels were measured. Toads exposed to ash accumulated significant concentrations of metals. Metal concentrations changed throughout the experiment, and profiles of accumulation and depuration differed depending on the metal and exposure regime. Ash-exposed toads exhibited elevated levels of 11 of 18 metals measured. Increases ranged from 47.5% for Pb to more than 5000% for As. Eight of 18 metals did not change in control toads, while 10 of 18 metals decreased in toads removed from ash, ranging from -25% for Co to -96% for Tl. Seven metals that decreased in toads removed from ash did not change in control toads.

  2. Geochemical speciation and dynamic of copper in tropical semi-arid soils exposed to metal-bearing mine wastes

    Energy Technology Data Exchange (ETDEWEB)

    Perlatti, Fabio [Department of Environmental Technology, National Department of Mineral Production – DNPM, Rua Dr. José Lourenço, 90560115-280 Fortaleza, CE (Brazil); Graduate Course of Ecology and Natural Resources, Department of Biology, Federal University of Ceará – UFC, Building 906, 60455-760, Fortaleza, CE (Brazil); Otero, Xosé Luis; Macias, Felipe [Department of Edaphology and Agricultural Chemistry, Faculty of Biology, University of Santiago de Compostela – USC, Rúa Lope Gómez de Marzoa, s/n. Campus sur, 15782 Santiago de Compostela (Spain); Ferreira, Tiago Osório, E-mail: toferreira@usp.br [Department of Soil Science, University of São Paulo (ESALQ/USP), Av. Pádua Dias, 11, 13418-900, Piracicaba, SP (Brazil); Graduate Course of Ecology and Natural Resources, Department of Biology, Federal University of Ceará – UFC, Building 906, 60455-760, Fortaleza, CE (Brazil)

    2014-12-01

    The potentially hazardous effects of rock wastes disposed at open pit in three different areas (Pr: Ore processing; Wr: Waste rock and Bd: Border) of an abandoned copper mine were evaluated in this study, with emphasis on acid drainage generation, metal contamination and copper geochemical dynamics in soils. Samples of waste rock were analyzed by Energy dispersive X-ray fluorescence (XRF), scanning electron microscopy with microanalysis (SEM-EDS) and X-ray diffraction (XRD). Soil samples were analyzed to determine the total metal contents (XRF), mineralogy (XRD), pH (H2O and H2O2), organic and inorganic carbon, % of total N, S and P, particle size, and a sequential extraction procedure was used to identify the different copper fractions. As a result of the prevalence of carbonates over sulphides in the wastes, the soil pH remained close to neutral, with absence of acid mine drainage. The geochemical interaction between these mineral phases seems to be the main mechanism to release Cu{sup 2+} ions. Total Cu in soils from the Pr area reached 11,180 mg.kg{sup −1}, while in Wr and Bd areas the values reached, on average, 4683 and 1086 mg.kg{sup −1}, respectively, indicating a very high level of soil contamination. In the Pr and Wr, the Cu was mainly associated with carbonates and amorphous iron oxides. In the Bd areas, the presence of vegetation has influenced the geochemical behavior of copper by increasing the dissolution of carbonates, affecting the buffer capacity of soils against sulphide oxidation, reducing the pH levels and enhancing the proportion of exchangeable and organic bound Cu. The present findings show that the use of plants or organic amendments in mine sites with high concentration of Cu carbonate-containing wastes should be viewed with caution, as the practice may enhance the mobilization of copper to the environment due to an increase in the rate of carbonates dissolution. - Highlights: • The hazardous effects of mine waste rocks at

  3. Inventory of heavy metal content in organic waste applied as fertilizer in agriculture: evaluating the risk of transfer into the food chain.

    Science.gov (United States)

    Lopes, Carla; Herva, Marta; Franco-Uría, Amaya; Roca, Enrique

    2011-07-01

    In this work, an environmental risk assessment of reusing organic waste of differing origins and raw materials as agricultural fertilizers was carried out. An inventory of the heavy metal content in different organic wastes (i.e., compost, sludge, or manure) from more than 80 studies at different locations worldwide is presented. The risk analysis was developed by considering the heavy metal (primarily Cd, Cu, Ni, Pb, and Zn) concentrations in different organic residues to assess their potential environmental accumulation and biotransfer to the food chain and humans. A multi-compartment model was used to estimate the fate and distribution of metals in different environmental compartments, and a multi-pathway model was used to predict human exposure. The obtained hazard index for each waste was concerning in many cases, especially in the sludge samples that yielded an average value of 0.64. Among the metals, Zn was the main contributor to total risk in all organic wastes due to its high concentration in the residues and high biotransfer potential. Other more toxic metals, like Cd or Pb, represented a negligible contribution. These results suggest that the Zn content in organic waste should be reduced or more heavily regulated to guarantee the safe management and reuse of waste residues according to the current policies promoted by the European Union.

  4. Effect of addition of sewage sludge and coal sludge on bioavailability of selected metals in the waste from the zinc and lead industry.

    Science.gov (United States)

    Sobik-Szołtysek, Jolanta; Wystalska, Katarzyna; Grobelak, Anna

    2017-07-01

    This study evaluated the content of bioavailable forms of selected heavy metals present in the waste from Zn and Pb processing that can potentially have an effect on the observed difficulties in reclamation of landfills with this waste. The particular focus of the study was on iron because its potential excess or deficiency may be one of the causes of the failure in biological reclamation. The study confirmed that despite high content of total iron in waste (mean value of 200.975gkg-1), this metal is present in the forms not available to plants (mean: 0.00009gkg-1). The study attempted to increase its potential bioavailability through preparation of the mixtures of this waste with additions in the form of sewage sludge and coal sludge in different proportions. Combination of waste with 10% of coal sludge and sewage sludge using the contents of 10%, 20% and 30% increased the amounts of bioavailable iron forms to the level defined as sufficient for adequate plant growth. The Lepidum sativum test was used to evaluate phytotoxicity of waste and the mixtures prepared based on this waste. The results did not show unambiguously that the presence of heavy metals in the waste had a negative effect on the growth of test plant roots. Copyright © 2017 Elsevier Inc. All rights reserved.

  5. Monitoring of ground water quality and heavy metals in soil during large scale bioremediation of petroleum hydrocarbon contaminated waste in India: case studies

    Directory of Open Access Journals (Sweden)

    Ajoy Kumar Mandal

    2014-10-01

    Full Text Available Bioremediation using microbes has been well accepted as an environmentally friendly and economical treatment method for disposal of hazardous petroleum hydrocarbon contaminated waste (oily waste and this type of bioremediation has been successfully conducted in laboratory and on a pilot scale in various countries, including India. Presently there are no federal regulatory guidelines available in India for carrying out field-scale bioremediation of oily waste using microbes. The results of the present study describe the analysis of ground water quality as well as selected heavy metals in oily waste in some of the large-scale field case studies on bioremediation of oily waste (solid waste carried out at various oil installations in India. The results show that there was no contribution of oil and grease and selected heavy metals to the ground water in the nearby area due to adoption of this bioremediation process. The results further reveal that there were no changes in pH and EC of the groundwater due to bioremediation. In almost all cases the selected heavy metals in residual oily waste were within the permissible limits as per Schedule – II of Hazardous Waste Management, Handling and Transboundary Movement Act, Amendment 2008, (HWM Act 2008, by the Ministry of Environment and Forests (MoEF, Government of India (GoI.

  6. Risk assessment of polychlorinated biphenyls and heavy metals in soils of an abandoned e-waste site in China.

    Science.gov (United States)

    Zhang, Quan; Ye, Jingjia; Chen, Jinyuan; Xu, Hangjie; Wang, Cui; Zhao, Meirong

    2014-02-01

    Risk assessment of abandoned e-waste recycling areas received little attention. Herein, we report the concentrations of 16 PCBs and 7 heavy metals in soils near an abandoned e-waste recycling plant in Taizhou, China. Our data showed that levels of tri-, tetra-, penta-, hexa-PCBs were 9.01, 5.56, 12.93, 3.13 mg/kg, and Pb, Cd, Cu were 6082.9, 42.3, 2364.2 mg/kg soil. Cd was the most prevalent contaminant with Nemerow index value of 44.3. Contaminants have been transported from the abandoned site to nearby areas. The ecology risk assessment based on the high toxicological effect in Chinese hamster ovary cells and earthworms showed that both PCBs and heavy metal residue pose high risk to the ecosystem. Hazard quotient showed that Pb, Cd, Hg and Cu pose high health risks for adults and children. Our results recommended a full examination of the risk and regulatory compliance of abandoned e-waste recycling areas in the future. Copyright © 2013 Elsevier Ltd. All rights reserved.

  7. Heavy metals concentrations of surface dust from e-waste recycling and its human health implications in southeast China.

    Science.gov (United States)

    Leung, Anna O W; Duzgoren-Aydin, Nurdan S; Cheung, K C; Wong, Ming H

    2008-04-01

    The recycling of printed circuit boards in Guiyu, China, a village intensely involved in e-waste processing, may present a significant environmental and human health risk. To evaluate the extent of heavy metals (Cd, Co, Cr, Cu, Ni, Pb, Zn) contamination from printed circuit board recycling, surface dust samples were collected from recycling workshops, adjacent roads, a schoolyard, and an outdoor food market. ICP-OES analyses revealed elevated mean concentrations in workshop dust (Pb 110,000, Cu 8360, Zn 4420, and Ni 1500 mg/kg) and in dust of adjacent roads (Pb 22,600, Cu 6170, Zn 2370, and Ni 304 mg/kg). Lead and Cu in road dust were 330 and 106, and 371 and 155 times higher, respectively, than non e-waste sites located 8 and 30 km away. Levels at the schoolyard and food market showed that public places were adversely impacted. Risk assessment predicted that Pb and Cu originating from circuit board recycling have the potential to pose serious health risks to workers and local residents of Guiyu, especially children, and warrants an urgent investigation into heavy metal related health impacts. The potential environmental and human health consequences due to uncontrolled e-waste recycling in Guiyu serves as a case study for other countries involved in similar crude recycling activities.

  8. Geochemistry and mineralogy of arsenic in mine wastes and stream sediments in a historic metal mining area in the UK.

    Science.gov (United States)

    Rieuwerts, J S; Mighanetara, K; Braungardt, C B; Rollinson, G K; Pirrie, D; Azizi, F

    2014-02-15

    Mining generates large amounts of waste which may contain potentially toxic elements (PTE), which, if released into the wider environment, can cause air, water and soil pollution long after mining operations have ceased. The fate and toxicological impact of PTEs are determined by their partitioning and speciation and in this study, the concentrations and mineralogy of arsenic in mine wastes and stream sediments in a former metal mining area of the UK are investigated. Pseudo-total (aqua-regia extractable) arsenic concentrations in all samples from the mining area exceeded background and guideline values by 1-5 orders of magnitude, with a maximum concentration in mine wastes of 1.8×10(5)mgkg(-1) As and concentrations in stream sediments of up to 2.5×10(4)mgkg(-1) As, raising concerns over potential environmental impacts. Mineralogical analysis of the wastes and sediments was undertaken by scanning electron microscopy (SEM) and automated SEM-EDS based quantitative evaluation (QEMSCAN®). The main arsenic mineral in the mine waste was scorodite and this was significantly correlated with pseudo-total As concentrations and significantly inversely correlated with potentially mobile arsenic, as estimated from the sum of exchangeable, reducible and oxidisable arsenic fractions obtained from a sequential extraction procedure; these findings correspond with the low solubility of scorodite in acidic mine wastes. The work presented shows that the study area remains grossly polluted by historical mining and processing and illustrates the value of combining mineralogical data with acid and sequential extractions to increase our understanding of potential environmental threats. Copyright © 2013 Elsevier B.V. All rights reserved.

  9. Inhibition of the heavy metal nitrification process at the Granollers waste water treatment plant; Inhibicion del proceso de nitrificacion por metales pesados en le EDAR de Granollers

    Energy Technology Data Exchange (ETDEWEB)

    Serrano Jimenez, M.; Jorda LLona, J.; Rovira Gallejones, S.; Freixo Rey, A.; Polo Canas, P.

    2004-07-01

    Nowadays is habitual to find wastewater treatment plants with nutrient removal in which industrial wastes in collectors are capable of inhibiting the nitrification process. This article is about a procedure to follow when determining the origin of this inhibition in a WWTP and finding the best solution to the problem. Through discontinuous rests of AUR we find a strong intoxication of the WWTP activated sludge. A pilot plant is started with this sludge at laboratory level to be able to activate the process at a real plant level. A bio sorption process is started up by using activated sludge. The results of metal decrease in water and mixed liquor because of sludge washing are presented, as well as the increase in nitrification speed and other authors experience in metal adsorption by secondary sludge. (Author)

  10. Influence of noble metal fission products and uranium on the microstructure and corrosion behaviour of D9 stainless steel–zirconium metal waste form alloy

    Energy Technology Data Exchange (ETDEWEB)

    Bairi, Lipika Rani, E-mail: lrbairi@gmail.com; Mallika, C., E-mail: mallika@igcar.gov.in; Kamachi Mudali, U., E-mail: kamachi@igcar.gov.in

    2014-05-01

    Highlights: • D9SS–Zr based Metal Waste Form (MWF) alloys were developed. • Microstructure of Noble Metal Fission Products (NMFPs) and U added MWF alloys was elucidated. • Zr-rich intermetallic phase hosts NMFP and U. • Leaching studies revealed the formation of stable hydrated passive film in NMFP–U–MWF alloys. - Abstract: Metal waste form (MWF) alloys of composition D9SS–8.5Zr, D9SS–10Zr–1NMFP and D9SS–10Zr–1NMFP–10U were prepared by casting of D9SS (Ti-modified austenitic 316 stainless steel), zirconium, NMFPs (noble metal fission products) and uranium for evaluating the influence of NMFPs and U on the microstructure and corrosion resistance of MWF alloys. Gradual increase in the hardness value was observed with the addition of NMFPs and uranium. Microstructural characterisation revealed the formation of Zr-rich intermetallic phases in these alloys which act as hosts for NMFPs and U. Fe–Zr and Ni–Zr based intermetallics were identified in D9SS–Zr and D9SS–Zr–NMFP alloys by XRD technique. In the U added alloy, UZrO{sub 2} and NiU{sub 2} were observed along with Fe–Zr and Ni–Zr intermetallics. Electrochemical corrosion monitoring confirmed active corrosion potential and higher passive current density with the addition of NMFPs and U. The MWF alloy with NMFPs showed higher break down potential with high polarization resistance revealing stable passive film.

  11. Small hazardous waste generators in developing countries: use of stabilization/solidification process as an economic tool for metal wastewater treatment and appropriate sludge disposal.

    Science.gov (United States)

    Silva, Marcos A R; Mater, Luciana; Souza-Sierra, Maria M; Corrêa, Albertina X R; Sperb, Rafael; Radetski, Claudemir M

    2007-08-25

    The aim of this study was to propose a profitable destination for an industrial sludge that can cover the wastewater treatment costs of small waste generators. Optimized stabilization/solidification technology was used to treat hazardous waste from an electroplating industry that is currently released untreated to the environment. The stabilized/solidified (S/S) waste product was used as a raw material to build concrete blocks, to be sold as pavement blocks or used in roadbeds and/or parking lots. The quality of the blocks containing a mixture of cement, lime, clay and waste was evaluated by means of leaching and solubility tests according to the current Brazilian waste regulations. Results showed very low metal leachability and solubility of the block constituents, indicating a low environmental impact. Concerning economic benefits from the S/S process and reuse of the resultant product, the cost of untreated heavy metal-containing sludge disposal to landfill is usually on the order of US$ 150-200 per tonne of waste, while 1tonne of concrete roadbed blocks (with 25% of S/S waste constitution) has a value of around US$ 100. The results of this work showed that the cement, clay and lime-based process of stabilization/solidification of hazardous waste sludge is sufficiently effective and economically viable to stimulate the treatment of wastewater from small industrial waste generators.

  12. Removing lead from metallic mixture of waste printed circuit boards by vacuum distillation: factorial design and removal mechanism.

    Science.gov (United States)

    Li, Xingang; Gao, Yujie; Ding, Hui

    2013-10-01

    The lead removal from the metallic mixture of waste printed circuit boards by vacuum distillation was optimized using experimental design, and a mathematical model was established to elucidate the removal mechanism. The variables studied in lead evaporation consisted of the chamber pressure, heating temperature, heating time, particle size and initial mass. The low-level chamber pressure was fixed at 0.1 Pa as the operation pressure. The application of two-level factorial design generated a first-order polynomial that agreed well with the data for evaporation efficiency of lead. The heating temperature and heating time exhibited significant effects on the efficiency, which was validated by means of the copper-lead mixture experiments. The optimized operating conditions within the region studied were the chamber pressure of 0.1 Pa, heating temperature of 1023 K and heating time of 120 min. After the conditions were employed to remove lead from the metallic mixture of waste printed circuit boards, the efficiency was 99.97%. The mechanism of the effects was elucidated by mathematical modeling that deals with evaporation, mass transfer and condensation, and can be applied to a wider range of metal removal by vacuum distillation. Copyright © 2013 Elsevier Ltd. All rights reserved.

  13. TiO2/bone composite materials for the separation of heavy metal impurities from waste water solutions

    Science.gov (United States)

    Dakroury, G.; Labib, Sh.; Abou El-Nour, F. H.

    2012-09-01

    Pure bone material obtained from cow meat, as apatite-rich material, and TiO2-bone composite materials are prepared and studied to be used for heavy metal ions separation from waste water solutions. Meat wastes are chemically and thermally treated to control their microstructure in order to prepare the composite materials that fulfill all the requirements to be used as selective membranes with high performance, stability and mechanical strength. The prepared materials are analyzed using Hg-porosimetry for surface characterization, energy dispersive X-ray spectroscopy (EDAX) for elemental analysis and Fourier transform infrared spectroscopy (FTIR) for chemical composition investigation. Structural studies are performed using X-ray diffraction (XRD). Microstructural properties are studied using scanning electron microscopy (SEM) and specific surface area studies are performed using Brunauer-Emmet-Teller (BET) method. XRD studies show that multiphase structures are obtained as a result of 1h sintering at 700-1200 °C for both pure bone and TiO2-bone composite materials. The factors affecting the transport of different heavy metal ions through the selected membranes are determined from permeation flux measurements. It is found that membrane pore size, membrane surface roughness and membrane surface charge are the key parameters that control the transport or rejection of heavy metal ions through the selected membranes.

  14. Phytoextraction of Heavy Metals from Soil Polluted with Waste Mining by Using Forage Plants in Successive Cultures

    Directory of Open Access Journals (Sweden)

    Anca Pricop

    2010-10-01

    Full Text Available During two years, was studied the phytoextraction potential of some perennial species (Medicago sativa and Trifolium pretense, Festuca arundinacea and Lolium perenne, for Zn, Cd, and Pb from soils polluted with waste mining. The experiment was done on kernozem soil with adding of 20 kg waste mining/m2 and 8 kg biosolid/m2. The results showed that in all experiments, rye-grass is a good extractor for Zn and Cd, and leguminous species for Pb. Both leguminous species, especially M. sativa, presented a high tolerance for lead toxicity, even with 3-4 times greater values than maximum allowable level from actual legislation. In all cases, regardless of the experimental variant, raygrass (Lolium perenne is a good accumulator of Zn and Cd, and red clover (Trifolium pratense of Pb. The values of metal bioaccumulation increase gradually with their concentration in soil. Quality of very good extractor of Pb displayed by Trifolium pratense species are kept even in case of excessive pollution with Pb, when it exceed 3.4 times the maximum permissible norms. This proves, as Medicago sativa species, a good tolerance and resistance to toxicity of this metal. In case of addition of natural zeolite-volcanic tuff there was no increase in the rate of Zn bioaccumulation. Only in case of Cd at Lolium perenne and Pb at Trifolium pratense appear the favourable effect of metallic ions bioavailability in soil for plants.

  15. Multiple biomarker responses (serum biochemistry, oxidative stress, genotoxicity and histopathology) in Channa punctatus exposed to heavy metal loaded waste water.

    Science.gov (United States)

    Javed, Mehjbeen; Ahmad, Md Irshad; Usmani, Nazura; Ahmad, Masood

    2017-05-10

    Experiments were conducted to investigate the health of fish Channa punctatus inhabiting heavy metal-loaded waste water. Heavy metals in the order of Fe > Mn > Zn > Co > Ni > Cu = Cr were present in the waste water. Gills had high metal load followed by liver and then kidney. Albumin, albumin to globulin (A:G) ratio, triglyceride, high density lipoprotein (HDL) and very low density lipoprotein (VLDL) were found to be lower but phospholipid, low density lipoprotein (LDL), total protein, lipid and cholesterol were higher as compared to the reference. Oxidative stress markers such as superoxide dismutase (SOD), catalase (CAT), glutathione S transferase (GST) and lipid peroxidation (LPO) were significantly higher in all tissues, whereas reduced glutathione (GSH) levels were comparatively low. Damage to DNA was observed with significantly higher mean tail length of comets in the exposed fish gill cells (30.9 µm) followed by liver (24.3 µm) and kidney (20.6 µm) as compared to reference fish (5.2, 4.8 and 5.9 µm respectively). Histopathology in gill, liver and kidney also showed marked damage. Integrated biochemical, oxidative stress, genotoxicity and histopathological findings are valuable biomarkers for native fish adaptive patterns, and monitoring of water quality/pollution of freshwater ecosystems.

  16. "Microscopic evidences of heavy metals distribution and anatomic alterations in breaching-leaves of Cupressus lindleyi growing around mining wastes".

    Science.gov (United States)

    Juan Miguel, Gómez-Bernal; Ofelia, Morton-Bermea; Esther Aurora, Ruiz-Huerta; Maria Aurora, Armienta-Hernández; Dávila Osiel, González

    2014-09-01

    In this article a study of the distribution of heavy metals in Cupressus lindleyi breaching-leaves was done in Taxco, Guerrero. At the same, heavy metals micro-localization was conducted in the breaching-leaves to understand the structural changes provoked by mining waste on plants. The most abundant contaminants in soils, tailings and different plant organs (roots, stems, and leaves) were Zn, Mn, and Pb. Nevertheless, As was more accumulated in the stem and breaching-leaves. The translocation factor and the bio-concentration factor were less than 1. The structural changes observed were the great accumulation of starch grains and phenolic compounds in the palisade parenchyma, changes in the hypodermis cell wall and necrotic zones in the palisade parenchyma. The distribution of heavy metals in breaching-leaves tissues was homogeneous in most of the elements. These results showed that C. lindleyi is a species that can be employed in phytostabilization of contaminated zones with mining waste because it is a native plant that does not require a lot of conditions for its development. © 2014 Wiley Periodicals, Inc.

  17. Leachate and Pollution Levels of Heavy Metals in the Groundwater near Municipal Solid Waste Landfill Site of Mashhad, Iran

    Directory of Open Access Journals (Sweden)

    Borhan Mansouri

    2014-06-01

    Full Text Available Background: The purpose of this study is to investigate the concentration of metals (lead, cadmium, chromium, copper, and nickel in the landfill leachate and heavy metals in wells downstream of municipal solid waste landfill site in the city of Mashhad. Methods: In both winter and summer seasons in 2009 samples were collected from five wells that were in landfill downstream in Mashhad. Results: Among heavy metals, nickel concentration in summer and lead concentration in winter had the highest levels. The results showed that the mean concentration of heavy metals in the studied wells was below the national standards of drinking water of Iran, WHO, and the United States. Pearson correlation coefficients also indicated that there was a significant correlation among the studied metals in the wells. Conclusion: Cd and Cu concentrations in all of the wells (except Pb in winter and Ni in summer did not pose any significant water quality problems since these concentrations were below the standards acceptable levels of drinking water.

  18. Microbial induced lipoprotein biosurfactant from slaughterhouse lipid waste and its application to the removal of metal ions from aqueous solution.

    Science.gov (United States)

    Ramani, K; Jain, S Chandan; Mandal, A B; Sekaran, G

    2012-09-01

    This study aims at demonstrating the production of lipoprotein biosurfactant from Pseudomonas gessardii using goat tallow, a slaughterhouse lipid waste, as the substrate and its application to the removal of metal ions from aqueous solution. The maximum bio-transformation of goat tallow into biosurfactant occurred at 48 h. The mass of the lipoprotein biosurfactant produced was 2.03 g/g of goat tallow. The biosurfactant was clearly characterized by surface tension, critical micelle concentration, emulsification index and molecular weight. The amino acid and fatty acid moieties of the biosurfactant were determined using High performance liquid chromatography (HPLC) and Gas chromatography (GC). The thermal behavior studies were evaluated using Thermo gravimetric (TG) and Differential scanning calorimetry (DSC) analysis. The lipoprotein biosurfactant was loaded onto the mesoporous activated carbon (MAC) for the sequestering of metal ions from the aqueous solution. The biosurfactant exhibited a removal efficiency for metal ions from aqueous solution in the order Cr(3+)>Ca(2+)>Cu(2+)>Fe(2+). The morphological observations and functional groups of the lipoprotein biosurfactant and that of the lipoprotein biosurfactant bound metal ions were determined using scanning electron micrograph (SEM) images and Fourier transform infrared (FT-IR) spectroscopy, respectively. This is the first report on the production of lipoprotein biosurfactant by P. gessardii using goat tallow as the substrate to sequester the metal ions from the aqueous solution. Copyright © 2012 Elsevier B.V. All rights reserved.

  19. Mobility of potentially harmful metals in latosols impacted by the municipal solid waste deposit of Londrina, Brazil

    Energy Technology Data Exchange (ETDEWEB)

    Souza Teixeira, Raquel, E-mail: raquel@uel.br [Universidade Estadual de Londrina, Departamento de Construcao Civil, C.P.6001, 86055-900, Londrina/PR (Brazil); Cambier, Philippe [INRA - AgroParisTech, UMR, Environnement et Grandes Cultures, 78850, Thiverval-Grignon (France); Davison Dias, Regina [Universidade Federal de Santa Catarina, Pos-Graduacao-ECV, Rua. Joao Pio Duarte s/n, Bairro Corrego Grande, 88040-970, Florianopolis/SC (Brazil); Peccinini Pinese, Jose Paulo [Universidade Estadual de Londrina, Departamento de Geociencias, C.P.6001, 86055-900, Londrina/PR (Brazil); Jaulin-Soubelet, Anne [INRA, UR251-PESSAC, Physicochimie et Ecotoxicologie des sols d' agrosystemes contamines, RD 10, 78000 Versailles (France)

    2010-01-15

    The contamination of soils by metals issuing from municipal solid waste (MSW) disposal in tropical environments has hardly been studied with regard to the particular problems associated with them, i.e., generally a high permeability of soils despite the abundance of clay, and the role of reactive Fe compounds. From a previous geotechnical and chemical survey, three latosol profiles differently affected by MSW leachates in the region of Londrina (Parana, Brazil) were selected. The aims were to evaluate the extent of their contamination, to better understand the fate of potentially harmful metals in tropical soils and rank the determining factors. Samples between 0.5 and 7 m depth were analyzed for their physical, mineralogical and chemical properties, and their micro-morphology was described by optical and transmission electron microscopy. Two steps of a sequential extraction procedure helped to assess the mobility of elements and to better discriminate between metals originating from pedogenesis and issued from MSW. These combined approaches showed that exposed soil profiles have been impacted at various depths, down to 7 m, through increased metal content, especially enhanced mobility of Zn, Co, Mn, Cu and Fe, and through increased salinity and organic matter. The mobility of potentially harmful metals should decrease with pH, which significantly increased in some impacted horizons, but other factors can reverse this trend.

  20. Development of an immobilization process for heavy metal containing galvanic solid wastes by use of sodium silicate and sodium tetraborate

    Energy Technology Data Exchange (ETDEWEB)

    Aydın, Ahmet Alper, E-mail: ahmetalperaydin@gmail.com [Chair of Urban Water Systems Engineering, Technische Universität München, Am Coulombwall, 85748 Garching (Germany); Aydın, Adnan [Istanbul Bilim University, School of Health, Esentepe, Istanbul, Sisli, 34394 (Turkey)

    2014-04-01

    Highlights: • A new physico-chemical process below 1000 °C for immobilization of galvanic sludges. • Sodium tetraborate and sodium silicate have been used as additives. • A strategy for adjustment of solid waste/additive mixture composition is presented. • Strategy is valid for wastes of hydrometallurgical and electro-plating processes. • Lower energy consumption and treated waste volume, shorter process time are provided. - Abstract: Heavy metal containing sludges from wastewater treatment plants of electroplating industries are designated as hazardous waste since their improper disposal pose high risks to environment. In this research, heavy metal containing sludges of electroplating industries in an organized industrial zone of Istanbul/Turkey were used as real-sample model for development of an immobilization process with sodium tetraborate and sodium silicate as additives. The washed sludges have been precalcined in a rotary furnace at 900 °C and fritted at three different temperatures of 850 °C, 900 °C and 950 °C. The amounts of additives were adjusted to provide different acidic and basic oxide ratios in the precalcined sludge-additive mixtures. Leaching tests were conducted according to the toxicity characteristic leaching procedure Method 1311 of US-EPA. X-ray diffraction (XRD), X-ray fluorescence (XRF), scanning electron microscope-energy dispersive spectrometer (SEM-EDS) and flame atomic absorption spectroscopy (FAAS) have been used to determine the physical and chemical changes in the products. Calculated oxide molar ratios in the precalcined sludge-additive mixtures and their leaching results have been used to optimize the stabilization process and to determine the intervals of the required oxide ratios which provide end-products resistant to leaching procedure of US-EPA. The developed immobilization-process provides lower energy consumption than sintering-vitrification processes of glass–ceramics.

  1. Characterization and management of waste water from desulphurization of flue gas by the wet absorption process with following oxidation. Karakterisering og behandling af spildevand fra roeggasafsvovling ved vaadabsorptionsprocessen med efterfoelgende oxidation

    Energy Technology Data Exchange (ETDEWEB)

    Mose Pedersen, B.; Holm Kristensen, G.

    1990-04-15

    The utilization of the wet absorption process for the desulphurization of flue gas from coal fired power plants produces calcium sulphate, and waste water containing nitrate, neutral salts and a certain amount of heavy metals. The conditions which influence the content of the waste water and methods for the precipitation of heavy metals are discussed. Data from abroad on the characterization of coal and methods of precipitaion are presented in detail. The focus is on mercury and cadmium as these chemicals are dangerous pollutives. It is concluded that, generally speaking, 100% of the mercury comes from the coal and 95-98% of the cadmium comes from the limestone used in the desulphurization process. It is claimed that hydroxide precipitation resulted in an acceptable concentration of heavy metals when the output concentration was low, when the latter was higher hydroxide/sulphide precipitation was necessary. (AB).

  2. Heavy metal removal from aqueous solutions using engineered magnetic biochars derived from waste marine macro-algal biomass.

    Science.gov (United States)

    Son, Eun-Bi; Poo, Kyung-Min; Chang, Jae-Soo; Chae, Kyu-Jung

    2018-02-15

    Despite the excellent sorption ability of biochar for heavy metals, it is difficult to separate and reuse after adsorption when applied to wastewater treatment process. To overcome these drawbacks, we developed an engineered magnetic biochar by pyrolyzing waste marine macro-algae as a feedstock, and we doped iron oxide particles (e.g., magnetite, maghemite) to impart magnetism. The physicochemical characteristics and adsorption properties of the biochar were evaluated. When compared to conventional pinewood sawdust biochar, the waste marine algae-based magnetic biochar exhibited a greater potential to remove heavy metals despite having a lower surface area (0.97m(2)/g for kelp magnetic biochar and 63.33m(2)/g for hijikia magnetic biochar). Although magnetic biochar could be effectively separated from the solution, however, the magnetization of the biochar partially reduced its heavy metal adsorption efficiency due to the biochar's surface pores becoming plugged with iron oxide particles. Therefore, it is vital to determine the optimum amount of iron doping that maximizes the biochar's separation without sacrificing its heavy metal adsorption efficiency. The optimum concentration of the iron loading solution for the magnetic biochar was determined to be 0.025-0.05mol/L. The magnetic biochar's heavy metal adsorption capability is considerably higher than that of other types of biochar reported previously. Further, it demonstrated a high selectivity for copper, showing two-fold greater removal (69.37mg/g for kelp magnetic biochar and 63.52mg/g for hijikia magnetic biochar) than zinc and cadmium. This high heavy metal removal performance can likely be attributed to the abundant presence of various oxygen-containing functional groups (COOH and OH) on the magnetic biochar, which serve as potential adsorption sites for heavy metals. The unique features of its high heavy metal removal performance and easy separation suggest that the magnetic algae biochar can potentially

  3. Climate accounting for waste management, Phase I and II. Summary: Phase 1: Glass Packaging, Metal packaging, paper, cardboard, plastic and wet organic waste. Phase 2: Wood waste and residual waste from households; Klimaregnskap for avfallshaandtering, Fase I og II. Sammendrag: Fase 1: Glassemballasje, metallemballasje, papir, papp, plastemballasje og vaatorganisk avfall. Fase 2: Treavfall og restavfall fra husholdninger

    Energy Technology Data Exchange (ETDEWEB)

    Raadal, Hanne Lerche; Modahl, Ingunn Saur; Lyng, Kari-Anne

    2009-09-15

    Background. On the basis of an increased focus on emissions of greenhouse gases in general, Waste Norway wanted to prepare a climate accounting for waste management in Norway. Oestfoldforskning was engaged to undertake the project. The aim of the project has been to develop a model for the calculation of net greenhouse gas emissions from different waste types of waste glass containers, metal containers, paper, cardboard, plastic, wet organic waste, wood waste and residual waste. The model is based on life cycle methodology and is used to calculate the net greenhouse gas emissions per kg of waste for the various waste management options and waste types, as well as to calculate the net greenhouse gas emissions for waste management for including waste types and quantities of 2006. There is an emphasis on developing a model so that municipalities / waste companies or regions can develop their own climate accounting for waste management in their region, based on site-specific conditions associated with types and amounts of waste, transport distances, type of treatment, exploitation and use of waste generated energy etc. The model can also be used as the basis for the preparation of useful documentation as the basis for information about waste systems utility in general, and as a basis for strategic reviews for Waste Norway and the waste sector in particular. Conclusions: The main conclusions from the project can be summarized as follows: 1. The results of the study clearly shows that to consider only one environmental indicator is too narrow approach to form the basis for decision making for selection of waste management solutions. 2. Net greenhouse gas emissions for waste management varies greatly, both between the different types of waste and treatment methods which are reviewed. The main results of the ranking of management methods in relation to the net greenhouse effect associated with the waste types and treatment methods are as follows: Recycling of materials

  4. Toxicity characteristic leaching procedure and iron treatment of brass foundry waste.

    Science.gov (United States)

    Kendall, Douglas S

    2003-01-15

    The Toxicity Characteristic Leaching Procedure (TCLP) is used by the United States Environmental Protection Agency to determine if wastes contain extractable components subject to hazardous waste regulations. This paper examines the limitations of the TCLP and the way it is used by studying a particular example. Waste casting sand from brass foundries to which iron metal has been added passes the TCLP test but when placed in a landfill for several years may start to leach lead, copper, and zinc. Results of TCLP tests of waste sand alone and with the additives iron metal, zinc metal, hydrous ferric oxide, and hematite are reported. Three processes were studied: reduction by metallic iron, sorption by hydrous ferric oxide, and precipitation of hydroxides. Lead, copper, and zinc behave differently with respect to these three processes, and their measurement allows some deductions as to what is occurring in a TCLP test or a landfill. Iron addition does not result in long-term stabilization of a waste placed in the ground. The chemistry of a laboratory extraction can be very different from the chemistry of a waste placed in the environment. Wastes that are treated to pass the TCLP test, but are not permanently stabilized, are a threat to the environment.

  5. Preparation of Metal Immobilized Orange Waste Gel for Arsenic(V Removal From Water

    Directory of Open Access Journals (Sweden)

    Biplob Kumar Biswas

    2014-05-01

    Full Text Available Abstract - The toxicity of arsenic is known to be a risk to aquatic flora and fauna and to human health even in relatively low concentration. In this research an adsorption gel was prepared from agricultural waste material (orange waste through simple chemical modification in the view to remove arsenic (V from water. Orange waste was crushed into small particles and saponified with Ca(OH2 to prepare saponified orange waste, which was further modified by immobilizing gadolinium(III to obtain desired adsorption material (Gd(III-immobilized SOW gel. The effective pH range for arsenic adsorption was found to be 7.5 – 8.5. Adsorption capacity of the gel was evaluated to be 0.45 mol-arsenic (V/kg. Dynamic adsorption of arsenic (V in column-mode was conducted and a dynamic capacity was found to be 0.39 mol/kg. Elution of arsenate was tested after complete saturation of the column packed with gadolinium-immobilized orange waste adsorption gel. A complete elution of arsenate was achieved with the help of 1 M HCl and 28 times pre-concentration factor was attained. This study showed that a cheap and abundant agro-industrial waste material could be successfully employed for the remediation of arsenic pollution in aquatic environment. Keywords: Arsenic; Orange waste; Gadolinium(III; Adsorption; Elution.

  6. Variation and distribution of metals and metalloids in soil/ash mixtures from Agbogbloshie e-waste recycling site in Accra, Ghana.

    Science.gov (United States)

    Itai, Takaaki; Otsuka, Masanari; Asante, Kwadwo Ansong; Muto, Mamoru; Opoku-Ankomah, Yaw; Ansa-Asare, Osmund Duodu; Tanabe, Shinsuke

    2014-02-01

    Illegal import and improper recycling of electronic waste (e-waste) are an environmental issue in developing countries around the world. African countries are no exception to this problem and the Agbogbloshie market in Accra, Ghana is a well-known e-waste recycling site. We have studied the levels of metal(loid)s in the mixtures of residual ash, formed by the burning of e-waste, and the cover soil, obtained using a portable X-ray fluorescence spectrometer (P-XRF) coupled with determination of the 1M HCl-extractable fraction by an inductively coupled plasma mass spectrometer. The accuracy and precision of the P-XRF measurements were evaluated by measuring 18 standard reference materials; this indicated the acceptable but limited quality of this method as a screening tool. The HCl-extractable levels of Al, Co, Cu, Zn, Cd, In, Sb, Ba, and Pb in 10 soil/ash mixtures varied by more than one order of magnitude. The levels of these metal(loid)s were found to be correlated with the color (i.e., soil/ash ratio), suggesting that they are being released from disposed e-waste via open burning. The source of rare elements could be constrained using correlation to the predominant metals. Human hazard quotient values based on ingestion of soil/ash mixtures exceeded unity for Pb, As, Sb, and Cu in a high-exposure scenario. This study showed that along with common metals, rare metal(loid)s are also enriched in the e-waste burning site. We suggest that risk assessment considering exposure to multiple metal(loid)s should be addressed in studies of e-waste recycling sites. © 2013. Published by Elsevier B.V. All rights reserved.

  7. Dynamic monitoring of structural changes in nickel hydroxide electrodes during discharge in batteries

    Energy Technology Data Exchange (ETDEWEB)

    Ortiz, M.; Becker, D.; Garaventta, G.; Visintin, A.; Castro, E.B. [Instituto de Investigaciones Fisicoquimicas Teoricas y Aplicadas (INIFTA), Facultad de Ciencias Exactas, Universidad Nacional de La Plata, C.C. 16, Suc. 4, 1900 La Plata (Argentina); Real, S.G., E-mail: sreal@inifta.unlp.edu.ar [Instituto de Investigaciones Fisicoquimicas Teoricas y Aplicadas (INIFTA), Facultad de Ciencias Exactas, Universidad Nacional de La Plata, C.C. 16, Suc. 4, 1900 La Plata (Argentina)

    2011-09-30

    The nickel hydroxide electrode is used as the positive plate of many rechargeable battery systems such as the nickel/cadmium, nickel/hydrogen, and nickel/metal hydrides. The electrochemical energy storage in the nickel hydroxide electrodes is related to the reversible characteristics of the redox couple nickel hydroxide/ox hydroxide. In the present work we describe the use of the electrochemical impedance spectroscopy (EIS) technique as a tool to characterize the dynamic behaviour of nickel hydroxide electrodes at different states of discharge (SOD) in KOH 7 M electrolytic solutions. The parameter identification procedure allows the estimation of the active area per unit volume, the solution conductivity as well as diffusion and kinetic constants related to the process, that represent very important parameters to evaluate the electrode performance.

  8. Assessment of heavy metals exposure, noise and thermal safety in the ambiance of a vacuum metallurgy separation system for recycling heavy metals from crushed e-wastes.

    Science.gov (United States)

    Zhan, Lu; Xu, Zhenming

    2014-12-01

    Vacuum metallurgy separation (VMS) is a technically feasible method to recover Pb, Cd and other heavy metals from crushed e-wastes. To further determine the environmental impacts and safety of this method, heavy metals exposure, noise and thermal safety in the ambiance of a vacuum metallurgy separation system are evaluated in this article. The mass concentrations of total suspended particulate (TSP) and PM10 are 0.1503 and 0.0973 mg m(-3) near the facilities. The concentrations of Pb, Cd and Sn in TSP samples are 0.0104, 0.1283 and 0.0961 μg m(-3), respectively. Health risk assessments show that the hazard index of Pb is 3.25 × 10(-1) and that of Cd is 1.09 × 10(-1). Carcinogenic risk of Cd through inhalation is 1.08 × 10(-5). The values of the hazard index and risk indicate that Pb and Cd will not cause non-cancerous effects or carcinogenic risk on workers. The noise sources are mainly the mechanical vacuum pump and the water cooling pump. Both of them have the noise levels below 80 dB (A). The thermal safety assessment shows that the temperatures of the vacuum metallurgy separation system surface are all below 303 K after adopting the circulated water cooling and heat insulation measures. This study provides the environmental information of the vacuum metallurgy separation system, which is of assistance to promote the industrialisation of vacuum metallurgy separation for recovering heavy metals from e-wastes. © The Author(s) 2014.

  9. Heavy Metal Contamination of Soils and Vegetation around Solid Waste Dumps in Port Harcourt, Nigeria

    National Research Council Canada - National Science Library

    Ideriah, T.J.K; Harry, F.O; Stanley, H.O; Igbara, J.K

    2011-01-01

    Assessment of the levels of copper, zinc and lead in soils and vegetation around solid waste dumpsites in Port Harcourt and environs were carried out in 2005 using Atomic Absorption spectrophotometric technique...

  10. Metals from mine waste as potential cause of oxidative stress in burrowing crab Neohelice granulata from San Antonio bay.

    Science.gov (United States)

    Giarratano, Erica; Gil, Mónica N; Marinho, Carmen H; Malanga, Gabriela

    2016-10-01

    The Natural Protected Area San Antonio bay is of particular importance for its congregation of migratory shorebirds and it has been declared one of the Western Hemisphere Shorebird Reserve Network International site (WHSRN). Present study represents the first assessment of variation on oxidative stress biomarkers in male crab Neohelice granulata from San Antonio bay (Río Negro, Argentina) under field conditions, associated mainly to metal contamination coming from passive mining wastes. Three sites were sampled once every three months from November 2012 to August 2013 within this sea inlet (Pile, Fishery and Port) and a control site at the southeast of the bay (Punta Perdices). Accumulation of Ni, Zn, Cr and Al varied only with seasons although without a constant trend, meanwhile Cd, Cu and Pb also varied among sites being highest in Pile and Port. Biochemical results indicated that variations in catalase activity was only site specific being maximum in Pile; meanwhile lipid radical, α-tocopherol and metallothioneins were only seasonal specific being higher in autumn and winter. Seasonal variation was also found for total thioles, being the content higher in summer and autumn than in winter. Correlation analysis revealed that malondialdehyde and α-tocopherol have a positive association with Al and negative with Ni, meanwhile GST has a positive association with Fe. Crabs from the closest area to the waste pile did not exhibit a differentiated oxidative pressure despite the higher accumulation of metals. It is possible that crabs from contaminated areas have developed a tolerance to metals, indicating a strong ecotoxicological selective pressure. More studies are needed to assess whether there is a transfer of metals through the food chain. Copyright © 2016 Elsevier Inc. All rights reserved.

  11. Effect of citric acid on metals mobility in pruning wastes and biosolids compost and metals uptake in Atriplex halimus and Rosmarinus officinalis.

    Science.gov (United States)

    Tapia, Y; Eymar, E; Gárate, A; Masaguer, A

    2013-05-01

    To assess metal mobility in pruning waste and biosolids compost (pH 6.9 and total concentration of metals in milligram per kilogram of Cd 1.9, Cu 132, Fe 8,513, Mn 192, Pb 81, and Zn 313), shrubs species Atriplex halimus and Rosmarinus officinalis were transplanted in this substrate and irrigated with citric acid (4 g L(-1), pH 2.9) and nutrient solution daily for 60 days. Citric acid significantly increased the concentrations of soluble Mn and Fe in the nutrient substrate solution measured by suction probes, while other metals did not vary in concentration (Cu and Zn) or were not observed at detectable levels (Cd and Pb). In plants, citric acid significantly increased the concentrations of Cu (2.7 ± 0.1-3.3 ± 0.1 mg kg(-1)), Fe (49.2 ± 5.2-76.8 ± 6.8 mg kg(-1)), and Mn (7.2 ± 1.1-11.4 ± 0.7 mg kg(-1)) in leaves of R. officinalis, whereas the concentration of only Mn (25.4 ± 0.3-42.2 ± 2.9 mg kg(-1)) was increased in A. halimus. Increasing Fe and Mn solubility by citric acid addition indicates the possibility of using it to improve plant nutrition. The mobility of metals in this substrate was influenced for the concentration of the metal, the degree of humification of organic matter and its high Fe content.

  12. THE ROLE OF LIQUID WASTE PRETREATMENT TECHNOLOGIES IN SOLVING THE DOE CLEAN-UP MISSION

    Energy Technology Data Exchange (ETDEWEB)

    Wilmarth, B; Sheryl Bush, S

    2008-10-31

    transition metal hydroxides that precipitate when the spent acidic process solutions are rendered alkaline with sodium hydroxide. The sludges contain Sr-90 and transuranic elements. The wastes stored at each site have been generated and stored for over fifty years. Although the majority of the wastes were generated to support nuclear weapons production and reprocessing, the wastes differ substantially between the sites. Table 5 shows the volumes and total radioactivity (including decay daughters) of the waste phases stored in tanks at each site. At Hanford, there are 177 tanks that contain 56.5 Mgal of waste. SRS has 51 larger tanks, of which 2 are closed, that contain 36.5 Mgal. Mainly due to recovery operations, the waste stored at Hanford has less total curies than that stored at Savannah River. The total radioactivity of the Hanford wastes contains approximately 190 MCi, and the total radioactivity of the Savannah River wastes contains 400 MCi.

  13. APPLICATION OF METAL RESISTANT BACTERIA BY MUTATIONAL ENHANCMENT TECHNIQUE FOR BIOREMEDIATION OF COPPER AND ZINC FROM INDUSTRIAL WASTES

    Directory of Open Access Journals (Sweden)

    M. R. Shakibaie ، A. Khosravan ، A. Frahmand ، S. Zare

    2008-10-01

    Full Text Available In this research, using mutation in the metal resistant bacteria, the bioremediation of the copper and zinc from copper factory effluents was investigated. Wastewater effluents from flocculation and rolling mill sections of a factory in the city of Kerman were collected and used for further experiments. 20 strains of Pseudomonas spp. were isolated from soil and effluents surrounding factory and identified by microbiological methods. Minimum inhibitory concentrations for copper (Cu and zinc (Zn were determined by agar dilution method. Those strains that exhibited highest minimum inhibitory concentrations values to the metals (5mM were subjected to 400-3200 mg/L concentrations of the three mutagenic agents, acriflavine, acridine orange and ethidium bromide. After determination of subinhibitory concentrations, the minimum inhibitory concentrations values for copper and zinc metal ions were again determined, which showed more than 10 fold increase in minimum inhibitory concentrations value (10 mM for Cu and 20 mM for Zn with P≤0.05. The atomic absorption spectroscopy of dried biomass obtained from resistant strains after exposure to mutagenic agents revealed that strains 13 accumulate the highest amount of intracellular copper (0.35% Cu/mg dried biomass and strain 10 showed highest accumulation of zinc (0.3% Zn/mg dried biomass respectively with P≤0.05. From above results it was concluded that the treatment of industrial waste containing heavy metals by artificially mutated bacteria may be appropriate solution for effluent disposal problems.

  14. Hydrogen Storage in Pristine and d10-Block Metal-Anchored Activated Carbon Made from Local Wastes

    Directory of Open Access Journals (Sweden)

    Mohamed F. Aly Aboud

    2015-04-01

    Full Text Available Activated carbon has been synthesized from local palm shell, cardboard and plastics municipal waste in the Kingdom of Saudi Arabia. It exhibits a surface area of 930 m2/g and total pore volume of 0.42 cm3/g. This pristine activated carbon has been further anchored with nickel, palladium and platinum metal particles by ultrasound-assisted impregnation. Deposition of nanosized Pt particles as small as 3 nm has been achieved, while for Ni and Pd their size reaches 100 nm. The solid-gas hydrogenation properties of the pristine and metal-anchored activated carbon have been determined. The pristine material exhibits a reversible hydrogen storage capacity of 2.3 wt% at 77 K and 3 MPa which is higher than for the doped ones. In these materials, the spillover effect due to metal doping is of minor importance in enhancing the hydrogen uptake compared with the counter-effect of the additional mass of the metal particles and pore blocking on the carbon surface.

  15. Phytochemical properties and heavy metal accumulation in wheat grain after three years’ fertilization with biogas digestate and mineral waste

    Directory of Open Access Journals (Sweden)

    Krzysztof Różyło

    2017-10-01

    Full Text Available Non-standard materials used for plant fertilization, require characterization to reduce any possible undesired effects. The aim of this study was to investigate the effect of fertilization with biogas digestate (BD and mining waste (carboniferous mudstones (MS from coal mine on wheat yield quality and the bioaccumulation of heavy metals in wheat grains in relation to conventional fertilization (NPK and no fertilization. Using the co-application of waste (MS+BD, the highest yield was obtained in the first and second year, but in the third year, a slight decrease in yield was observed compared to NPK. In all years, BD and MS+BD fertilization increased the content of protein, wet gluten, and phenols in wheat grain compared to NPK and no fertilization. Waste fertilization had a positive effect on the antioxidant capacity index of grain but only in the first year. The bioaccumulation index (BAI demonstrated that NPK decreased BAI for Zn, B, Cd, and Mn, whereas MS+BD decreased BAI for Cu, Sr, Pb, Co, Ba, and Cr.

  16. Occurrences and inventories of heavy metals and brominated flame retardants in wastes from printed circuit board production.

    Science.gov (United States)

    Zhou, Xiaoyu; Guo, Jie; Zhang, Wei; Zhou, Peng; Deng, Jingjing; Lin, Kuangfei

    2014-09-01

    Pollutants including heavy metals and brominated flame retardant were detected in 10 types of production wastes from a typical printed circuit board manufacturing plant, and their inventories were estimated. Rinsing water from etching process had the highest concentrations of copper (665.51 mg/L), lead (1.02 mg/L), nickel (3.60 mg/L), chromium (0.97 mg/L), and tin (1.79 mg/L). Powdered solid waste (SW) from the cut lamination process contained the highest tetrabromobisphenol-A (TBBPA) levels (49.86 mg/kg). Polybrominated diphenyl ethers (PBDEs) were absent in this plant, in agreement with the international regulations of PBDE phase out. The pollutant inventories in the wastes exhibited in the order of copper > > zinc > tin ≈ nickel > lead > chromium > > TBBPA. The potential environmental impact of pollutants in SW during production and disposal were further investigated. A high partitioning of pollutant concentration between the total suspended particle and SW (-0.10 powder with the smallest particle diameter still showed high leachabilities of lead and tin which may lead to a negative environmental impact during disposal.

  17. Coupling scales for modelling heavy metal vaporization from municipal solid waste incineration in a fluid bed by CFD

    Energy Technology Data Exchange (ETDEWEB)

    Soria, José, E-mail: jose.soria@probien.gob.ar [Institute for Research and Development in Process Engineering, Biotechnology and Alternative Energies (PROBIEN, CONICET – UNCo), 1400 Buenos Aires St., 8300 Neuquén (Argentina); Gauthier, Daniel; Flamant, Gilles [Processes, Materials and Solar Energy Laboratory (PROMES-CNRS, UPR 8521), 7 Four Solaire Street, Odeillo, 66120 Font-Romeu (France); Rodriguez, Rosa [Chemical Engineering Institute, National University of San Juan, 1109 Libertador (O) Avenue, 5400 San Juan (Argentina); Mazza, Germán [Institute for Research and Development in Process Engineering, Biotechnology and Alternative Energies (PROBIEN, CONICET – UNCo), 1400 Buenos Aires St., 8300 Neuquén (Argentina)

    2015-09-15

    Highlights: • A CFD two-scale model is formulated to simulate heavy metal vaporization from waste incineration in fluidized beds. • MSW particle is modelled with the macroscopic particle model. • Influence of bed dynamics on HM vaporizatio