Design and performance of feed-delivery systems for simulated radioactive waste slurries

International Nuclear Information System (INIS)

Perez, J.M. Jr.

1983-02-01

Processes for vitrifying simulated high-level radioactive waste have been developed at the Pacific Northwest Laboratory (PNL) over the last several years. Paralleling this effort, several feed systems used to deliver the simulated waste slurry to the melter have been tested. Because there had been little industrial experience in delivering abrasive slurries at feed rates of less than 10 L/min, early experience helped direct the design of more-dependable systems. Also, as feed delivery requirements changed, the feed system was modified to meet these new requirements. The various feed systems discussed in this document are part of this evolutionary process, so they have not been ranked against each other. The four slurry feed systems discussed are: (1) vertical-cantilevered centrifugal pump system; (2) airlift feed systems; (3) pressurized-loop systems; and (4) positive-displacement pump system. 20 figures, 11 tables

Waste feed delivery environmental permits and approvals plan

International Nuclear Information System (INIS)

Papp, I.G.

1998-01-01

This document describes the range of environmental actions, including required permits and other agency approvals, that may affect waste feed delivery (WFD) activities in the Hanford Site's Tank Waste Remediation System (TWRS). This plan expands on the summary level information in the Tank Waste Remediation System Environmental Program Plan (HNF 1773) to address requirements that are most pertinent to WFD. This plan outlines alternative approaches to satisfying applicable environmental standards, and describes selected strategies for acquiring permits and other approvals needed for WFD to proceed. Appendices at the end of this plan provide preliminary cost and schedule estimates for implementing the selected strategies. The rest of this section summarizes the scope of WFD activities, including important TWRS operating information, and describes in more detail the objectives, structure, and content of this plan

Assessment of the Electrical Power Requirements for Continued Safe Storage and Waste Feed Delivery Phase One

International Nuclear Information System (INIS)

MAY, T.H.

2000-01-01

This study evaluated the ability of the electrical distribution system to support safe storage as well as the first phase of the Waste Feed Delivery. Several recommendations are made to improve the electrical system. The ability to assure adequate Waste Feed Delivery (WFD) to the Privatization Contractor's vitrification facility is a key element in the overall Hanford cleanup schedule. An important aspect of this WFD is the availability of sufficient and appropriate electrical power in the single- and double-shell tank farms. The methodology for performing this review and the results are described

Waste Feed Delivery Raw Water and Potable Water and Compressed Air Capacity Evaluation

International Nuclear Information System (INIS)

MAY, T.H.

2000-01-01

This study evaluated the ability of the Raw Water, Potable Water, and Compressed Air systems to support safe storage as well as the first phase of the Waste Feed Delivery. Several recommendations are made to improve the system

THE HANFORD WASTE FEED DELIVERY OPERATIONS RESEARCH MODEL

International Nuclear Information System (INIS)

Berry, J.; Gallaher, B.N.

2011-01-01

Washington River Protection Solutions (WRPS), the Hanford tank farm contractor, is tasked with the long term planning of the cleanup mission. Cleanup plans do not explicitly reflect the mission effects associated with tank farm operating equipment failures. EnergySolutions, a subcontractor to WRPS has developed, in conjunction with WRPS tank farms staff, an Operations Research (OR) model to assess and identify areas to improve the performance of the Waste Feed Delivery Systems. This paper provides an example of how OR modeling can be used to help identify and mitigate operational risks at the Hanford tank farms.

Analysis of Waste Leak and Toxic Chemical Release Accidents from Waste Feed Delivery (WFD) Diluent System

Energy Technology Data Exchange (ETDEWEB)

WILLIAMS, J.C.

2000-09-15

Radiological and toxicological consequences are calculated for 4 postulated accidents involving the Waste Feed Delivery (WFD) diluent addition systems. Consequences for the onsite and offsite receptor are calculated. This analysis contains technical information used to determine the accident consequences for the River Protection Project (RPP) Final Safety Analysis Report (FSAR).

Analysis of Waste Leak and Toxic Chemical Release Accidents from Waste Feed Delivery (WFD) Diluent System

International Nuclear Information System (INIS)

WILLIAMS, J.C.

2000-01-01

Radiological and toxicological consequences are calculated for 4 postulated accidents involving the Waste Feed Delivery (WFD) diluent addition systems. Consequences for the onsite and offsite receptor are calculated. This analysis contains technical information used to determine the accident consequences for the River Protection Project (RPP) Final Safety Analysis Report (FSAR)

Evaluation of the Validity of three Criteria for Sampling and Analyzing DST Wastes in Support of Waste Feed Delivery

International Nuclear Information System (INIS)

BOGER, R.M.

2000-01-01

This document summarizes the analysis of 3 basic criteria for the sampling systems that will provide waste validation samples of tank waste feeds prior to delivery to the waste treatment and immobilization plant where the wastes will be converted to glass forms. The assessed criteria includes sampling through a 4-inch riser, sampling while a mixer pump is operating, and the deployment of an at-tank analysis system. The assessment, based on the Phase I, 3S6 waste feed scenario, indicated that for high level waste, sampling through a 4-inch riser is not required but sampling while mixer pumps are operating will be required. For low activity waste, sampling through a 4-inch riser will be required but sampling while mixer pumps are operating is not required. The assessment indicated that an at-tank analysis system to provide tank mixing/settling (homogeneity) status is not needed since the number of tanks providing LAW feed was expanded and the payment basis in the original privatization contract has been modified

High Level Waste Feed Delivery AZ-101 Batch Transfer to the Private Contractor Transfer and Mixing Process Improvements

International Nuclear Information System (INIS)

DUNCAN, G.P.

2000-01-01

The primary purpose of this business case is to provide Operations and Maintenance with a detailed transfer process review for the first High Level Waste (HLW) feed delivery to the Privatization Contractor (PC), AZ-101 batch transfer to PC. The Team was chartered to identify improvements that could be implemented in the field. A significant penalty can be invoked for not providing the quality, quantity, or timely delivery of HLW feed to the PC

Waste Feed Delivery System Phase 1 Preliminary Reliability and Availability and Maintainability Analysis [SEC 1 and 2

International Nuclear Information System (INIS)

CARLSON, A.B.

1999-01-01

The document presents updated results of the preliminary reliability, availability, maintainability analysis performed for delivery of waste feed from tanks 241-AZ-101 and 241-AN-105 to British Nuclear Fuels Limited, inc. under the Tank Waste Remediation System Privatization Contract. The operational schedule delay risk is estimated and contributing factors are discussed

Waste Feed Delivery System Phase 1 Preliminary Reliability and Availability and Maintainability Analysis [SEC 1 and 2

Energy Technology Data Exchange (ETDEWEB)

CARLSON, A.B.

1999-11-11

The document presents updated results of the preliminary reliability, availability, maintainability analysis performed for delivery of waste feed from tanks 241-AZ-101 and 241-AN-105 to British Nuclear Fuels Limited, inc. under the Tank Waste Remediation System Privatization Contract. The operational schedule delay risk is estimated and contributing factors are discussed.

Low Activity Waste Feed Process Control Strategy

International Nuclear Information System (INIS)

STAEHR, T.W.

2000-01-01

The primary purpose of this document is to describe the overall process control strategy for monitoring and controlling the functions associated with the Phase 1B high-level waste feed delivery. This document provides the basis for process monitoring and control functions and requirements needed throughput the double-shell tank system during Phase 1 high-level waste feed delivery. This document is intended to be used by (1) the developers of the future Process Control Plan and (2) the developers of the monitoring and control system

Double Shell Tanks (DST) and Waste Feed Delivery Project Management Quality Affecting Procedures Management Plan

International Nuclear Information System (INIS)

LUND, D.P.

2000-01-01

The purpose of the Double Shell Tanks (DST) and Waste Feed Delivery (WFD) Management Assessment Plan is to define how management assessments within DST h WFD will be conducted. The plan as written currently includes only WFD Project assessment topics. Other DST and WFD group assessment topics will be added in future revisions

Load requirements for maintaining structural integrity of Hanford single-shell tanks during waste feed delivery and retrieval activities

International Nuclear Information System (INIS)

JULYK, L.J.

1999-01-01

This document provides structural load requirements and their basis for maintaining the structural integrity of the Hanford Single-Shell Tanks during waste feed delivery and retrieval activities. The requirements are based on a review of previous requirements and their basis documents as well as load histories with particular emphasis on the proposed lead transfer feed tanks for the privatized vitrification plant

High-Level Waste (HLW) Feed Process Control Strategy

International Nuclear Information System (INIS)

STAEHR, T.W.

2000-01-01

The primary purpose of this document is to describe the overall process control strategy for monitoring and controlling the functions associated with the Phase 1B high-level waste feed delivery. This document provides the basis for process monitoring and control functions and requirements needed throughput the double-shell tank system during Phase 1 high-level waste feed delivery. This document is intended to be used by (1) the developers of the future Process Control Plan and (2) the developers of the monitoring and control system

Evaluating Feed Delivery Performance in Scaled Double-Shell Tanks

International Nuclear Information System (INIS)

Lee, Kearn P.; Thien, Michael G.

2013-01-01

The Hanford Tank Operations Contractor (TOC) and the Hanford Waste Treatment and Immobilization Plant (WTP) contractor are both engaged in demonstrating mixing, sampling, and transfer system capability using simulated Hanford High-Level Waste (HLW) formulations. This work represents one of the remaining technical issues with the high-level waste treatment mission at Hanford. The TOCs' ability to adequately mix and sample high-level waste feed to meet the WTP WAC Data Quality Objectives must be demonstrated. The tank mixing and feed delivery must support both TOC and WTP operations. The tank mixing method must be able to remove settled solids from the tank and provide consistent feed to the WTP to facilitate waste treatment operations. Two geometrically scaled tanks were used with a broad spectrum of tank waste simulants to demonstrate that mixing using two rotating mixer jet pumps yields consistent slurry compositions as the tank is emptied in a series of sequential batch transfers. Testing showed that the concentration of slow settling solids in each transfer batch was consistent over a wide range of tank operating conditions. Although testing demonstrated that the concentration of fast settling solids decreased by up to 25% as the tank was emptied, batch-to-batch consistency improved as mixer jet nozzle velocity in the scaled tanks increased

Infectious waste feed system

Science.gov (United States)

Coulthard, E. James

1994-01-01

An infectious waste feed system for comminuting infectious waste and feeding the comminuted waste to a combustor automatically without the need for human intervention. The system includes a receptacle for accepting waste materials. Preferably, the receptacle includes a first and second compartment and a means for sealing the first and second compartments from the atmosphere. A shredder is disposed to comminute waste materials accepted in the receptacle to a predetermined size. A trough is disposed to receive the comminuted waste materials from the shredder. A feeding means is disposed within the trough and is movable in a first and second direction for feeding the comminuted waste materials to a combustor.

Melter feed viscosity during conversion to glass: Comparison between low-activity waste and high-level waste feeds

Energy Technology Data Exchange (ETDEWEB)

Jin, Tongan [Pacific Northwest National Laboratory, Richland Washington; Chun, Jaehun [Pacific Northwest National Laboratory, Richland Washington; Dixon, Derek R. [Pacific Northwest National Laboratory, Richland Washington; Kim, Dongsang [Pacific Northwest National Laboratory, Richland Washington; Crum, Jarrod V. [Pacific Northwest National Laboratory, Richland Washington; Bonham, Charles C. [Pacific Northwest National Laboratory, Richland Washington; VanderVeer, Bradley J. [Pacific Northwest National Laboratory, Richland Washington; Rodriguez, Carmen P. [Pacific Northwest National Laboratory, Richland Washington; Weese, Brigitte L. [Pacific Northwest National Laboratory, Richland Washington; Schweiger, Michael J. [Pacific Northwest National Laboratory, Richland Washington; Kruger, Albert A. [U.S. Department of Energy, Office of River Protection, Richland Washington; Hrma, Pavel [Pacific Northwest National Laboratory, Richland Washington

2017-12-07

During nuclear waste vitrification, a melter feed (generally a slurry-like mixture of a nuclear waste and various glass forming and modifying additives) is charged into the melter where undissolved refractory constituents are suspended together with evolved gas bubbles from complex reactions. Knowledge of flow properties of various reacting melter feeds is necessary to understand their unique feed-to-glass conversion processes occurring within a floating layer of melter feed called a cold cap. The viscosity of two low-activity waste (LAW) melter feeds were studied during heating and correlated with volume fractions of undissolved solid phase and gas phase. In contrast to the high-level waste (HLW) melter feed, the effects of undissolved solid and gas phases play comparable roles and are required to represent the viscosity of LAW melter feeds. This study can help bring physical insights to feed viscosity of reacting melter feeds with different compositions and foaming behavior in nuclear waste vitrification.

Waste Feed Evaporation Physical Properties Modeling

International Nuclear Information System (INIS)

Daniel, W.E.

2003-01-01

This document describes the waste feed evaporator modeling work done in the Waste Feed Evaporation and Physical Properties Modeling test specification and in support of the Hanford River Protection Project (RPP) Waste Treatment Plant (WTP) project. A private database (ZEOLITE) was developed and used in this work in order to include the behavior of aluminosilicates such a NAS-gel in the OLI/ESP simulations, in addition to the development of the mathematical models. Mathematical models were developed that describe certain physical properties in the Hanford RPP-WTP waste feed evaporator process (FEP). In particular, models were developed for the feed stream to the first ultra-filtration step characterizing its heat capacity, thermal conductivity, and viscosity, as well as the density of the evaporator contents. The scope of the task was expanded to include the volume reduction factor across the waste feed evaporator (total evaporator feed volume/evaporator bottoms volume). All the physical properties were modeled as functions of the waste feed composition, temperature, and the high level waste recycle volumetric flow rate relative to that of the waste feed. The goal for the mathematical models was to predict the physical property to predicted simulation value. The simulation model approximating the FEP process used to develop the correlations was relatively complex, and not possible to duplicate within the scope of the bench scale evaporation experiments. Therefore, simulants were made of 13 design points (a subset of the points used in the model fits) using the compositions of the ultra-filtration feed streams as predicted by the simulation model. The chemistry and physical properties of the supernate (the modeled stream) as predicted by the simulation were compared with the analytical results of experimental simulant work as a method of validating the simulation software

Evaluation of 241-AZ tank farm supporting phase 1 privatization waste feed delivery

Energy Technology Data Exchange (ETDEWEB)

CARLSON, A.B.

1998-11-19

This evaluation is one in a series of evaluations determining the process needs and assessing the adequacy of existing and planned equipment in meeting those needs at various double-shell tank farms in support of Phase 1 privatization. A number of tank-to-tank transfers and waste preparation activities are needed to process and feed waste to the private contractor in support of Phase 1 privatization. The scope of this evaluation is limited to process needs associated with 241-AZ tank farm during the Phase 1 privatization.

Evaluation of 241-AZ tank farm supporting phase 1 privatization waste feed delivery

International Nuclear Information System (INIS)

CARLSON, A.B.

1998-01-01

This evaluation is one in a series of evaluations determining the process needs and assessing the adequacy of existing and planned equipment in meeting those needs at various double-shell tank farms in support of Phase 1 privatization. A number of tank-to-tank transfers and waste preparation activities are needed to process and feed waste to the private contractor in support of Phase 1 privatization. The scope of this evaluation is limited to process needs associated with 241-AZ tank farm during the Phase 1 privatization

HLW Feed Delivery AZ101 Batch Transfer to the Private Contractor Transfer and Mixing Process Improvements [Initial Release at Rev 2

Energy Technology Data Exchange (ETDEWEB)

DUNCAN, G.P.

2000-02-28

The primary purpose of this business case is to provide Operations and Maintenance with a detailed transfer process review for the first High Level Waste (HLW) feed delivery to the Privatization Contractor (PC), AZ-101 batch transfer to PC. The Team was chartered to identify improvements that could be implemented in the field. A significant penalty can be invoked for not providing the quality, quantity, or timely delivery of HLW feed to the PC.

Initial Investigation of Waste Feed Delivery Tank Mixing and Sampling Issues

International Nuclear Information System (INIS)

Fort, James A.; Bamberger, Judith A.; Meyer, Perry A.; Stewart, Charles W.

2007-01-01

The Hanford tank farms contractor will deliver waste to the Waste Treatment Plant (WTP) from a staging double-shell tank. The WTP broadly classifies waste it receives in terms of 'Envelopes,' each with different limiting properties and composition ranges. Envelope A, B, and C wastes are liquids that can include up to 4% entrained solids that can be pumped directly from the staging DST without mixing. Envelope D waste contains insoluble solids and must be mixed before transfer. The mixing and sampling issues lie within Envelope D solid-liquid slurries. The question is how effectively these slurries are mixed and how representative the grab samples are that are taken immediately after mixing. This report summarizes the current state of knowledge concerning jet mixing of wastes in underground storage tanks. Waste feed sampling requirements are listed, and their apparent assumption of uniformity by lack of a requirement for sample representativeness is cited as a significant issue. The case is made that there is not an adequate technical basis to provide such a sampling regimen because not enough is known about what can be achieved in mixing and distribution of solids by use of the baseline submersible mixing pump system. A combined mixing-sampling test program is recommended to fill this gap. Historical Pacific Northwest National Laboratory project and tank farms contractor documents are used to make this case. A substantial investment and progress are being made to understand mixing issues at the WTP. A summary of the key WTP activities relevant to this project is presented in this report. The relevant aspects of the WTP mixing work, together with a previously developed scaled test strategy for determining solids suspension with submerged mixer pumps (discussed in Section 3) provide a solid foundation for developing a path forward

Data quality objectives for TWRS privatization Phase 1: Confirm tank T is an appropriate feed source for low-activity waste feed batch X

International Nuclear Information System (INIS)

Certa, P.J.

1998-01-01

The Phase 1 privatization contracts require that the Project Hanford Management Contract (PHMC) contractors, on behalf of the US Department of Energy, Richland Operations Office (RL), deliver the appropriate quantities of the proper composition of feed on schedule to the Privatization contractors (DOE-RL 1996). The type of feed needed, the amount of feed needed, and the overall timing of when feed is to be delivered to the Privatization contractor are specified by the contract. Additional requirements are imposed by the interface control document (ICD) for low-activity waste (LAW) feed (PHMC 1997a). The Tank Waste Remediation System Operation and Utilization Plan (TWRSO/UP) as updated by the Readiness-to-Proceed (RTP) deliverable establishes the baseline operating scenario for the delivery of feed to two Privatization contractors for the first twelve LAW batches. The project master baseline schedule (PMBS) and corresponding logic diagrams that will be used to implement the operating scenario have been developed and are currently being refined. The baseline operating scenario in the TWRSO/UP/RTP specifies which tanks will be used to provide feed for each specific feed batch, the operational activities needed to prepare and deliver each feed batch, and the timing of these activities. This operating scenario has considered such factors as the privatization contracts and ICD requirements, waste composition and chemistry, equipment availability, project schedules and funding, tank farm logistics and the availability of tank space. The PMBS includes activities to reduce programmatic risk

Data quality objectives for TWRS privatization Phase 1: Confirm tank T is an appropriate feed source for low-activity waste feed batch X

Energy Technology Data Exchange (ETDEWEB)

Certa, P.J.

1998-07-02

The Phase 1 privatization contracts require that the Project Hanford Management Contract (PHMC) contractors, on behalf of the US Department of Energy, Richland Operations Office (RL), deliver the appropriate quantities of the proper composition of feed on schedule to the Privatization contractors (DOE-RL 1996). The type of feed needed, the amount of feed needed, and the overall timing of when feed is to be delivered to the Privatization contractor are specified by the contract. Additional requirements are imposed by the interface control document (ICD) for low-activity waste (LAW) feed (PHMC 1997a). The Tank Waste Remediation System Operation and Utilization Plan (TWRSO/UP) as updated by the Readiness-to-Proceed (RTP) deliverable establishes the baseline operating scenario for the delivery of feed to two Privatization contractors for the first twelve LAW batches. The project master baseline schedule (PMBS) and corresponding logic diagrams that will be used to implement the operating scenario have been developed and are currently being refined. The baseline operating scenario in the TWRSO/UP/RTP specifies which tanks will be used to provide feed for each specific feed batch, the operational activities needed to prepare and deliver each feed batch, and the timing of these activities. This operating scenario has considered such factors as the privatization contracts and ICD requirements, waste composition and chemistry, equipment availability, project schedules and funding, tank farm logistics and the availability of tank space. The PMBS includes activities to reduce programmatic risk.

Remotely controlled reagent feed system for mixed waste treatment Tank Farm

International Nuclear Information System (INIS)

Dennison, D.K.; Bowers, J.S.; Reed, R.K.

1995-02-01

LLNL has developed and installed a large-scale. remotely controlled, reagent feed system for use at its existing aqueous low-level radioactive and mixed waste treatment facility (Tank Farm). LLNL's Tank Farm is used to treat aqueous low-level and mixed wastes prior to vacuum filtration and to remove the hazardous and radioactive components before it is discharged to the City of Livermore Water Reclamation Plant (LWRP) via the sanitary sewer in accordance with established limits. This reagent feed system was installed to improve operational safety and process efficiency by eliminating the need for manual handling of various reagents used in the aqueous waste treatment processes. This was done by installing a delivery system that is controlled either remotely or locally via a programmable logic controller (PLC). The system consists of a pumping station, four sets of piping to each of six 6,800-L (1,800-gal) treatment tanks, air-actuated discharge valves at each tank, a pH/temperature probe at each tank, and the PLC-based control and monitoring system. During operation, the reagents are slowly added to the tanks in a preprogrammed and controlled manner while the pH, temperature, and liquid level are continuously monitored by the PLC. This paper presents the purpose of this reagent feed system, provides background related to LLNL's low-level/mixed waste treatment processes, describes the major system components, outlines system operation, and discusses current status and plans

WTP Waste Feed Qualification: Glass Fabrication Unit Operation Testing Report

Energy Technology Data Exchange (ETDEWEB)

Stone, M. E. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL). Hanford Missions Programs; Newell, J. D. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL). Process Technology Programs; Johnson, F. C. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL). Engineering Process Development; Edwards, T. B. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL). Engineering Process Development

2016-07-14

The waste feed qualification program is being developed to protect the Hanford Tank Waste Treatment and Immobilization Plant (WTP) design, safety basis, and technical basis by assuring waste acceptance requirements are met for each staged waste feed campaign prior to transfer from the Tank Operations Contractor to the feed receipt vessels inside the Pretreatment Facility. The Waste Feed Qualification Program Plan describes the three components of waste feed qualification: 1. Demonstrate compliance with the waste acceptance criteria 2. Determine waste processability 3. Test unit operations at laboratory scale. The glass fabrication unit operation is the final step in the process demonstration portion of the waste feed qualification process. This unit operation generally consists of combining each of the waste feed streams (high-level waste (HLW) and low-activity waste (LAW)) with Glass Forming Chemicals (GFCs), fabricating glass coupons, performing chemical composition analysis before and after glass fabrication, measuring hydrogen generation rate either before or after glass former addition, measuring rheological properties before and after glass former addition, and visual observation of the resulting glass coupons. Critical aspects of this unit operation are mixing and sampling of the waste and melter feeds to ensure representative samples are obtained as well as ensuring the fabrication process for the glass coupon is adequate. Testing was performed using a range of simulants (LAW and HLW simulants), and these simulants were mixed with high and low bounding amounts of GFCs to evaluate the mixing, sampling, and glass preparation steps in shielded cells using laboratory techniques. The tests were performed with off-the-shelf equipment at the Savannah River National Laboratory (SRNL) that is similar to equipment used in the SRNL work during qualification of waste feed for the Defense Waste Processing Facility (DWPF) and other waste treatment facilities at the

Hanford Tank Waste Treatment and Immobilization Plant (WTP) Waste Feed Qualification Program Development Approach - 13114

Energy Technology Data Exchange (ETDEWEB)

Markillie, Jeffrey R.; Arakali, Aruna V.; Benson, Peter A.; Halverson, Thomas G. [Hanford Tank Waste Treatment and Immobilization Plant Project, Richland, WA 99354 (United States); Adamson, Duane J.; Herman, Connie C.; Peeler, David K. [Savannah River National Laboratory, Aiken, SC 29808 (United States)

2013-07-01

The Hanford Tank Waste Treatment and Immobilization Plant (WTP) is a nuclear waste treatment facility being designed and constructed for the U.S. Department of Energy by Bechtel National, Inc. and subcontractor URS Corporation (under contract DE-AC27-01RV14136 [1]) to process and vitrify radioactive waste that is currently stored in underground tanks at the Hanford Site. A wide range of planning is in progress to prepare for safe start-up, commissioning, and operation. The waste feed qualification program is being developed to protect the WTP design, safety basis, and technical basis by assuring acceptance requirements can be met before the transfer of waste. The WTP Project has partnered with Savannah River National Laboratory to develop the waste feed qualification program. The results of waste feed qualification activities will be implemented using a batch processing methodology, and will establish an acceptable range of operator controllable parameters needed to treat the staged waste. Waste feed qualification program development is being implemented in three separate phases. Phase 1 required identification of analytical methods and gaps. This activity has been completed, and provides the foundation for a technically defensible approach for waste feed qualification. Phase 2 of the program development is in progress. The activities in this phase include the closure of analytical methodology gaps identified during Phase 1, design and fabrication of laboratory-scale test apparatus, and determination of the waste feed qualification sample volume. Phase 3 will demonstrate waste feed qualification testing in support of Cold Commissioning. (authors)

Alternative fish feed production from waste chicken feathers

Directory of Open Access Journals (Sweden)

Sri Jumini

2017-08-01

Full Text Available In this This devotion has been done to provide education and training of the utilization of waste chicken manure, making flour chicken feathers as a fish feed alternative, that can overcome some of the problems that waste chicken feathers from the center cutting broiler chickens in the village Krasak enough, it causes pollution, and not used optimally; Low public awareness of awareness of environmental pollution; the lack of public knowledge about the utilization of waste chicken feathers, and processing technology, as well as to address the needs of fish feed more expensive, need alternative feed ingredients. This service program has provided insight to the public about waste chicken feathers so that it can be used as a new entrepreneurial startups. To achieve these objectives have been done of activity as follows: 1 Provide counseling and understanding of the community will be a negative impact on the environment of waste chicken feathers. 2 Provide counseling utilization of waste chicken feathers for people in nearby farms. 3 Make a chicken feather meal of chicken feather waste as an alternative fish feed to improve digestibility of chicken feathers. 3 The formation of the group for increasing the economic income of the family. This service activities program runs quite well with demonstrated some activity, namely: 1 Change Behavior Society (knowledge transfer; 2 Chicken Feather Extension Waste Utilization; 3 Making Unit Waste Chicken Feathers; 4 Establishment of New Business of Diversified Waste Chicken Feathers.

Compression device for feeding a waste material to a reactor

Science.gov (United States)

Williams, Paul M.; Faller, Kenneth M.; Bauer, Edward J.

2001-08-21

A compression device for feeding a waste material to a reactor includes a waste material feed assembly having a hopper, a supply tube and a compression tube. Each of the supply and compression tubes includes feed-inlet and feed-outlet ends. A feed-discharge valve assembly is located between the feed-outlet end of the compression tube and the reactor. A feed auger-screw extends axially in the supply tube between the feed-inlet and feed-outlet ends thereof. A compression auger-screw extends axially in the compression tube between the feed-inlet and feed-outlet ends thereof. The compression tube is sloped downwardly towards the reactor to drain fluid from the waste material to the reactor and is oriented at generally right angle to the supply tube such that the feed-outlet end of the supply tube is adjacent to the feed-inlet end of the compression tube. A programmable logic controller is provided for controlling the rotational speed of the feed and compression auger-screws for selectively varying the compression of the waste material and for overcoming jamming conditions within either the supply tube or the compression tube.

Feed Basis for Processing Relatively Low Radioactivity Waste Tanks

International Nuclear Information System (INIS)

Pike, J.A.

2002-01-01

This paper presents the characterization of potential feed for processing relatively low radioactive waste tanks. The feed characterization is based on waste characterization data extracted from the waste characterization system. This data is compared to salt cake sample results from Tanks 37, 38 and 41

Remote waste handling and feed preparation for Mixed Waste Management

International Nuclear Information System (INIS)

Couture, S.A.; Merrill, R.D.; Densley, P.J.

1995-05-01

The Mixed Waste Management Facility (MWMF) at the Lawrence Livermore National Laboratory (LLNL) will serve as a national testbed to demonstrate mature mixed waste handling and treatment technologies in a complete front-end to back-end --facility (1). Remote operations, modular processing units and telerobotics for initial waste characterization, sorting and feed preparation have been demonstrated at the bench scale and have been selected for demonstration in MWMF. The goal of the Feed Preparation design team was to design and deploy a robust system that meets the initial waste preparation flexibility and productivity needs while providing a smooth upgrade path to incorporate technology advances as they occur. The selection of telerobotics for remote handling in MWMF was made based on a number of factors -- personnel protection, waste generation, maturity, cost, flexibility and extendibility. Modular processing units were selected to enable processing flexibility and facilitate reconfiguration as new treatment processes or waste streams are brought on line for demonstration. Modularity will be achieved through standard interfaces for mechanical attachment as well as process utilities, feeds and effluents. This will facilitate reconfiguration of contaminated systems without drilling, cutting or welding of contaminated materials and with a minimum of operator contact. Modular interfaces also provide a standard connection and disconnection method that can be engineered to allow convenient remote operation

Environmental and health impacts of using food waste as animal feed: a comparative analysis of food waste management options.

Science.gov (United States)

Salemdeeb, Ramy; Zu Ermgassen, Erasmus K H J; Kim, Mi Hyung; Balmford, Andrew; Al-Tabbaa, Abir

2017-01-01

The disposal of food waste is a large environmental problem. In the United Kingdom (UK), approximately 15 million tonnes of food are wasted each year, mostly disposed of in landfill, via composting, or anaerobic digestion (AD). European Union (EU) guidelines state that food waste should preferentially be used as animal feed though for most food waste this practice is currently illegal, because of disease control concerns. Interest in the potential diversion of food waste for animal feed is however growing, with a number of East Asian states offering working examples of safe food waste recycling - based on tight regulation and rendering food waste safe through heat treatment. This study investigates the potential benefits of diverting food waste for pig feed in the UK. A hybrid, consequential life cycle assessment (LCA) was conducted to compare the environmental and health impacts of four technologies for food waste processing: two technologies of South Korean style-animal feed production (as a wet pig feed and a dry pig feed) were compared with two widespread UK disposal technologies: AD and composting. Results of 14 mid-point impact categories show that the processing of food waste as a wet pig feed and a dry pig feed have the best and second-best scores, respectively, for 13/14 and 12/14 environmental and health impacts. The low impact of food waste feed stems in large part from its substitution of conventional feed, the production of which has substantial environmental and health impacts. While the re-legalisation of the use of food waste as pig feed could offer environmental and public health benefits, this will require support from policy makers, the public, and the pig industry, as well as investment in separated food waste collection which currently occurs in only a minority of regions.

Alternatives Generation and Analysis for Heat Removal from High Level Waste Tanks

International Nuclear Information System (INIS)

WILLIS, W.L.

2000-01-01

This document addresses the preferred combination of design and operational configurations to provide heat removal from high-level waste tanks during Phase 1 waste feed delivery to prevent the waste temperature from exceeding tank safety requirement limits. An interim decision for the preferred method to remove the heat from the high-level waste tanks during waste feed delivery operations is presented herein

Alternatives Generation and Analysis for Heat Removal from High Level Waste Tanks

Energy Technology Data Exchange (ETDEWEB)

WILLIS, W.L.

2000-06-15

This document addresses the preferred combination of design and operational configurations to provide heat removal from high-level waste tanks during Phase 1 waste feed delivery to prevent the waste temperature from exceeding tank safety requirement limits. An interim decision for the preferred method to remove the heat from the high-level waste tanks during waste feed delivery operations is presented herein.

Particulate waste outflow from fish-farming cages. How much is uneaten feed?

Science.gov (United States)

Ballester-Moltó, M; Sanchez-Jerez, P; Cerezo-Valverde, J; Aguado-Giménez, F

2017-06-15

Particulate wastes drive benthic organic enrichment from cage fish farming. Differentiation between faeces and uneaten feed estimates at cage level are of great value to both economize the feeding process and reduce waste. This study estimates the particulate waste outflowing cages at different depths and orientations, and the wasted feed component by combining in situ measurements and modelling. Particulate matter flux (PMF) was greater vertically through the cage bottoms (60.89%), but lateral outflow was also substantial (39.11%). PMF occurs all around the cages, and the influence of the mainstream current was low. Wasted feed was greatly variable, reaching high values (about 50% of supplied feed. The self-application of feed wastage monitoring and estimates by fish farmers is recommended to improve sustainability. Copyright © 2017 Elsevier Ltd. All rights reserved.

Tank waste remediation system retrieval authorization basis amendment task plan

International Nuclear Information System (INIS)

Goetz, T.G.

1998-01-01

This task plan is a documented agreement between Nuclear Safety and Licensing and the Process Development group within the Waste Feed Delivery organization. The purpose of this task plan is to identify the scope of work, tasks and deliverables, responsibilities, manpower, and schedules associated with an authorization basis amendment as a result of the Waste Feed Waste Delivery Program, Project W-211, and Project W-TBD

Feed intake and growth performance of goats supplemented with soy waste

Directory of Open Access Journals (Sweden)

Mohammad Mijanur Rahman

2014-07-01

Full Text Available The objective of this work was to evaluate the effects of supplemental feeding of soy waste on the feed intake and growth rate of goats. Twenty male crossbred (Boer x local goats were assigned to two isonitrogenous diet groups: one of commercial pellet and the other of soy waste. The commercial pellet (1.0% and soy waste (0.8% were provided on the dry matter basis of body weight (BW per day, to the respective group of each diet. The soy waste group had lower daily intakes of total dry matter (0.79 vs. 0.88 kg and organic matter (665.71 vs. 790.44 g than the group fed pellet; however, the differences on daily intakes for grass (0.62 vs. 0.64 kg, crude protein (96.81 vs. 96.83 g, and neutral detergent fibre (483.70 vs. 499.86 g were not significant. No differences were observed between groups for BW gain. The feed conversion ratio and feed cost per kilogram of BW gain were lower for the group fed soy waste than for the one fed pellet. Goats fed supplemental soy waste have a lower total dry matter intake, feed conversion ratio, and feed cost per kilogram of body weight gain than those fed commercial pellets.

Alternatives Generation and Analysis for Phase 1 High-Level Waste Feed Tanks Selection

International Nuclear Information System (INIS)

CRAWFORD, T.W.

1999-01-01

A recent revision of the US Department of Energy privatization contract for the immobilization of high-level waste (HLW) at Hanford necessitates the investigation of alternative waste feed sources to meet contractual feed requirements. This analysis identifies wastes to be considered as HLW feeds and develops and conducts alternative analyses to comply with established criteria. A total of 12,426 cases involving 72 waste streams are evaluated and ranked in three cost-based alternative models. Additional programmatic criteria are assessed against leading alternative options to yield an optimum blended waste feed stream

LOW ACTIVITY WASTE FEED SOLIDS CARACTERIZATION AND FILTERABILITY TESTS

Energy Technology Data Exchange (ETDEWEB)

McCabe, D.; Crawford, C.; Duignan, M.; Williams, M.; Burket, P.

2014-04-03

The primary treatment of the tank waste at the DOE Hanford site will be done in the Waste Treatment and Immobilization Plant (WTP) that is currently under construction. The baseline plan for the WTP Pretreatment facility is to treat the waste, splitting it into High Level Waste (HLW) feed and Low Activity Waste (LAW) feed. Both waste streams are then separately vitrified as glass and sealed in canisters. The LAW glass will be disposed onsite in the Integrated Disposal Facility (IDF). There are currently no plans to treat the waste to remove technetium in the WTP Pretreatment facility, so its disposition path is the LAW glass. Options are being explored to immobilize the LAW portion of the tank waste, i.e., the LAW feed from the WTP Pretreatment facility. Removal of {sup 99}Tc from the LAW Feed, followed by off-site disposal of the {sup 99}Tc, would eliminate a key risk contributor for the IDF Performance Assessment (PA) for supplemental waste forms, and has potential to reduce treatment and disposal costs. Washington River Protection Solutions (WRPS) is developing some conceptual flow sheets for LAW treatment and disposal that could benefit from technetium removal. One of these flowsheets will specifically examine removing {sup 99}Tc from the LAW feed stream to supplemental immobilization. The conceptual flow sheet of the {sup 99}Tc removal process includes a filter to remove insoluble solids prior to processing the stream in an ion exchange column, but the characteristics and behavior of the liquid and solid phases has not previously been investigated. This report contains results of testing of a simulant that represents the projected composition of the feed to the Supplemental LAW process. This feed composition is not identical to the aqueous tank waste fed to the Waste Treatment Plant because it has been processed through WTP Pretreatment facility and therefore contains internal changes and recycle streams that will be generated within the WTP process. Although

Determining the amount of waste plastics in the feed of Austrian waste-to-energy facilities.

Science.gov (United States)

Schwarzböck, Therese; Van Eygen, Emile; Rechberger, Helmut; Fellner, Johann

2017-02-01

Although thermal recovery of waste plastics is widely practiced in many European countries, reliable information on the amount of waste plastics in the feed of waste-to-energy plants is rare. In most cases the amount of plastics present in commingled waste, such as municipal solid waste, commercial, or industrial waste, is estimated based on a few waste sorting campaigns, which are of limited significance with regard to the characterisation of plastic flows. In the present study, an alternative approach, the so-called Balance Method, is used to determine the total amount of plastics thermally recovered in Austria's waste incineration facilities in 2014. The results indicate that the plastics content in the waste feed may vary considerably among different plants but also over time. Monthly averages determined range between 8 and 26 wt% of waste plastics. The study reveals an average waste plastics content in the feed of Austria's waste-to-energy plants of 16.5 wt%, which is considerably above findings from sorting campaigns conducted in Austria. In total, about 385 kt of waste plastics were thermally recovered in all Austrian waste-to-energy plants in 2014, which equals to 45 kg plastics cap -1 . In addition, the amount of plastics co-combusted in industrial plants yields a total thermal utilisation rate of 70 kg cap -1  a -1 for Austria. This is significantly above published rates, for example, in Germany reported rates for 2013 are in the range of only 40 kg of waste plastics combusted per capita.

The association between cesarean delivery on maternal request and method of newborn feeding in China.

Directory of Open Access Journals (Sweden)

Xinxue Liu

Full Text Available Cesarean delivery has increased significantly during the last decades. This study aimed to investigate the association between planned mode of delivery and method of feeding.A cohort was created retrospectively using data from a population-based maternal and child health surveillance system, which covers 27 study sites in China from 1993 to 2006. The cohort consisted of 431,704 women for analysis, including 22,462 women with planned cesarean delivery on maternal request (CDMR and 409,242 women with planned vaginal delivery (VD. Logistic regression models were used to examine the association between mode of delivery and method of feeding adjusting for selected covariates. In this cohort, 398,176 (92.2% women exclusively breastfed their baby, 28,798 (6.7% women chose mixed feeding, and 4,730 (1.1% women chose formula feeding before hospital discharge. Women who planned CDMR were less likely to exclusively breastfeed and more likely to formula feed their babies than those who planned VD. After adjusting for covariates, the odds ratios were 0.85 (95% CI: 0.81-0.89 for exclusive breastfeeding and 1.61 (95% CI: 1.45-1.79 for formula feeding. Associations between planned mode of delivery and method of feeding in the south, north, rural and urban areas yielded similar results.This study demonstrated that planned CDMR was associated with a lower rate of exclusive breastfeeding and a higher rate of formula feeding in a low-risk Chinese population.

Alternatives generation and analysis for phase I intermediate waste feed staging system design requirements

Energy Technology Data Exchange (ETDEWEB)

Britton, M.D.

1996-10-02

This document provides; a decision analysis summary; problem statement; constraints, requirements, and assumptions; decision criteria; intermediate waste feed staging system options and alternatives generation and screening; intermediate waste feed staging system design concepts; intermediate waste feed staging system alternative evaluation and analysis; and open issues and actions.

In Vitro Evaluation of Eslicarbazepine Delivery via Enteral Feeding Tubes.

Science.gov (United States)

Reindel, Kristin; Zhao, Fang; Hughes, Susan; Dave, Vivek S

2017-12-01

Purpose: The feasibility of preparing an eslicarbazepine acetate suspension using Aptiom tablets for administration via enteral feeding tubes was evaluated. Methods: Eslicarbazepine acetate suspension (40 mg/mL) was prepared using Aptiom tablets after optimizing the tablet crushing methods and the vehicle composition. A stability-indicating high-performance liquid chromatography (HPLC) method was developed to monitor the eslicarbazepine stability in the prepared suspension. Three enteric feeding tubes of various composition and dimensions were evaluated for the delivery of the suspensions. The suspension was evaluated for the physical and chemical stability for 48 hours. Results: The reproducibility and consistency of particle size reduction was found to be best with standard mortar/pestle. The viscosity analysis and physical stability studies showed that ORA-Plus:water (50:50 v/v) was optimal for suspending ability and flowability of suspension through the tubes. The developed HPLC method was found to be stability indicating and suitable for the assay of eslicarbazepine acetate in the prepared suspension. The eslicarbazepine concentrations in separately prepared suspensions were within acceptable range (±3%), indicating accuracy and reproducibility of the procedure. The eslicarbazepine concentrations in suspensions before and after delivery through the enteric feeding tubes were within acceptable range (±4%), indicating absence of any physical/chemical interactions of eslicarbazepine with the tubes and a successful delivery of eslicarbazepine dosage via enteric feeding tubes. The stability study results showed that eslicarbazepine concentration in the suspension remained unchanged when stored at room temperature for 48 hours. Conclusion: The study presents a convenient procedure for the preparation of a stable suspension of eslicarbazepine acetate (40 mg/mL) using Aptiom tablets, for administration via enteral feeding tubes.

The low-level waste handling challenge at the Feed Materials Production Center

International Nuclear Information System (INIS)

Harmon, J.E.; Diehl, D.E.; Gardner, R.L.

1988-02-01

The management of low-level wastes from the production of depleted uranium at the Feed Materials Production Center presents an enormous challenge. The recovery of uranium from materials contaminated with depleted uranium is usually not economical. As a result, large volumes of wastes are generated. The Westinghouse Materials Company of Ohio has established an aggressive waste management program. Simple solutions have been applied to problems in the areas of waste handling and waste minimization. The success of this program has been demonstrated by the reduction of low-level waste inventory at the Feed Materials Production Center. 8 refs., 4 figs

The low-level waste handling challenge at the Feed Materials Production Center

International Nuclear Information System (INIS)

Harmon, J.E.; Diehl, D.E.; Gardner, R.L.

1988-01-01

The management of low-level wastes from the production of depleted uranium at the Feed Materials Production Center presents an enormous challenge. The recovery of uranium from materials contaminated with depleted uranium is usually not economical. As a result, large volumes of wastes are generated. The Westinghouse Materials Company of Ohio has established an aggressive waste management program. Simple solutions have been applied to problems in the areas of waste handling and waste minimization. The success of this program has been demonstrated by the reduction of low-level waste inventory at the Feed Materials Production Center

Agroindustrial and Chicken Poultry Waste as Feed Supplement for Nila Fish (Oreochromis sp)

International Nuclear Information System (INIS)

Harsojo, L.S.; Andini, S.H.; Rosalina, S.; Suwirma

2000-01-01

An experiment was conducted to study the use of industrial waste such as soybean sauce waste, tofu waste and chicken manure as feed supplement for nila fish raised in in ponds to increase the body weight. There were four compositions i.e composition A consisted of soybean sauce waste mixed with the other materials; composition B consisted of irradiated chicken manure mixed with the other materials; composition C was commercial pellet as control and composition D was tofu waste . The feeding with the amount of 3% from total body weight was given to the fishes three times per day. The quality of food measured with the conversion value (amount of feed for 1 kg body weight gain) and the quality of water i.e pH, temperature and oxygen concentration were also measured. Determination of heavy metal content in fish and water were carried out using the atomic absorption spectrophotometer (AAS). Results of the experiment showed that feed of composition A (soybean sauce waste) at 12 th 21 st weeks had lowest conversion value although statistically there was no different significant among the others feed. The content of heavy metals in all fish and water were under permissible limit and also for Fe content was also under permissible limit.There were no Salmonella found in the industrial waste. This means that industrial waste can be used safely as feed supplement for fish and has also the same effect compared to the commercial pelletized for the growth of fish. The water quality was found suitable for the growth of fish

Application of ''Confirm tank T is an appropriate feed source for Low-Activity waste feed batch X'' to specific feed batches

International Nuclear Information System (INIS)

JO, J.

1999-01-01

This document addresses the characterization needs of tanks as set forth in the ''Confirm Tank T is an Appropriate Feed Source for Low-Activity Waste Feed Batch X'' Data Quality Objective (DQO) (Certa and Jo 1998). The primary purpose of this document is to collect existing data and identify the data needed to determine whether or not the feed source(s) are appropriate for a specific batch before transfer is made to the feed staging tanks. To answer these questions, the existing tank data must be collected and a detailed review performed. If the existing data are insufficient to complete a full comparison, additional data must be obtained from the feed source(s). Additional information requirements need to be identified and formally documented, then the source tank waste must be sampled or resampled and analyzed. Once the additional data are obtained, the data shall be incorporated into the existing database for the source tank and a reevaluation of the data against the DQO must be made

Recycle food wastes into high quality fish feeds for safe and quality fish production.

Science.gov (United States)

Wong, Ming-Hung; Mo, Wing-Yin; Choi, Wai-Ming; Cheng, Zhang; Man, Yu-Bon

2016-12-01

The amount of food waste generated from modern societies is increasing, which has imposed a tremendous pressure on its treatment and disposal. Food waste should be treated as a valuable resource rather than waste, and turning it into fish feeds would be a viable alternative. This paper attempts to review the feasibility of using food waste to formulate feed pellets to culture a few freshwater fish species, such as grass carp, grey mullet, and tilapia, under polyculture mode (growing different species in the same pond). These species occupy different ecological niches, with different feeding modes (i.e., herbivorous, filter feeding, etc.), and therefore all the nutrients derived from the food waste could be efficiently recycled within the ecosystem. The problems facing environmental pollution and fish contamination; the past and present situation of inland fish culture (focusing on South China); upgrade of food waste based feed pellets by adding enzymes, vitamin-mineral premix, probiotics (yeast), prebiotics, and Chinese medicinal herbs into feeds; and potential health risks of fish cultivated by food waste based pellets are discussed, citing some local examples. It can be concluded that appropriate portions of different types of food waste could satisfy basic nutritional requirements of lower trophic level fish species such as grass carp and tilapia. Upgrading the fish pellets by adding different supplements mentioned above could further elevated the quality of feeds, leading to higher growth rates, and enhanced immunity of fish. Health risk assessments based on the major environmental contaminants (mercury, PAHs and DDTs) in fish flesh showed that fish fed food waste based pellets are safer for consumption, when compared with those fed commercial feed pellets. Copyright © 2016 Elsevier Ltd. All rights reserved.

Determining the amount of waste plastics in the feed of Austrian waste-to-energy facilities

OpenAIRE

Schwarzb?ck, Therese; Van Eygen, Emile; Rechberger, Helmut; Fellner, Johann

2016-01-01

Although thermal recovery of waste plastics is widely practiced in many European countries, reliable information on the amount of waste plastics in the feed of waste-to-energy plants is rare. In most cases the amount of plastics present in commingled waste, such as municipal solid waste, commercial, or industrial waste, is estimated based on a few waste sorting campaigns, which are of limited significance with regard to the characterisation of plastic flows. In the present study, an alternati...

Modifying the rheological properties of melter feed for the Hanford Waste Vitrification Plant

International Nuclear Information System (INIS)

Blair, H.T.; McMakin, A.H.

1986-03-01

Selected high-level nuclear wastes from the Hanford Site may be vitrified in the future Hanford Waste Vitrification Plant (HWVP) by Rockwell Hanford Company, the contractor responsible for reprocessing and waste management at the Hanford Site. The Pacific Northwest Laboratory (PNL), is responsible for providing technical support for the HWVP. In this capacity, PNL performed rheological evaluations of simulated HWVP feed in order to determine which processing factors could be modified to best optimize the vitrification process. To accomplish this goal, a simulated HWVP feed was first created and characterized. Researchers then evaluated how the chemical and physical form of the glass-forming additives affected the rheological properties and melting behavior of melter feed prepared with the simulated HWVP feed. The effects of adding formic acid to the waste were also evaluated. Finally, the maximum melter feed concentration with acceptable rheological properties was determined

A junk-food hypothesis for gannets feeding on fishery waste

Science.gov (United States)

Grémillet, David; Pichegru, Lorien; Kuntz, Grégoire; Woakes, Anthony G; Wilkinson, Sarah; Crawford, Robert J.M; Ryan, Peter G

2008-01-01

Worldwide fisheries generate large volumes of fishery waste and it is often assumed that this additional food is beneficial to populations of marine top-predators. We challenge this concept via a detailed study of foraging Cape gannets Morus capensis and of their feeding environment in the Benguela upwelling zone. The natural prey of Cape gannets (pelagic fishes) is depleted and birds now feed extensively on fishery wastes. These are beneficial to non-breeding birds, which show reduced feeding effort and high survival. By contrast, breeding gannets double their diving effort in an attempt to provision their chicks predominantly with high-quality, live pelagic fishes. Owing to a scarcity of this resource, they fail and most chicks die. Our study supports the junk-food hypothesis for Cape gannets since it shows that non-breeding birds can survive when complementing their diet with fishery wastes, but that they struggle to reproduce if live prey is scarce. This is due to the negative impact of low-quality fishery wastes on the growth patterns of gannet chicks. Marine management policies should not assume that fishery waste is generally beneficial to scavenging seabirds and that an abundance of this artificial resource will automatically inflate their populations. PMID:18270155

Perspectives regarding antenatal care, delivery and breast feeding practices of women from Baluchistan, Pakistan

International Nuclear Information System (INIS)

Khoso, A.; Khan, A.Z.; Sayed, S.A.; Rafique, G.

2016-01-01

Background: Antenatal Care is one of the fundamental rights for women to safeguard their health. Neonatal mortality rates have remained relatively static, compared to the decline in infant and under 5 mortality rates, adverse practices regarding breast feeding and pre-lacteal feeds being the important factors responsible. This study aimed to explore the Antenatal Care, delivery and breast feeding practices in three districts of Blotchiness. Methods: It was a qualitative phenomenological design using Constrictive approach. The study was conducted in three districts of Baluchistan province, Gwadar, Quetta, Qila Saifullah. There were a total of 14 Focus Group Discussions with women regarding Antenatal Care, delivery and Breast feeding practices, followed by audio taping, transcription as verbatim and analysis through Nvivo version 2. A process was deployed for identification and reporting of the components in order to ensure quality and validity of the qualitative findings. Results: Across the sites, women attended ANC at least once. However, their descriptions of ANC often varied. The women preferred Dais instead of doctors, due to the affordability, customs and availability. A lack of trained doctors and long distances to get a check-up lead to home deliveries in the study setting. Colostrum was discarded by majority of the mothers, while prelacteal feed was a common practice. Conclusion: This paper has explored factors affecting ANC attendance, delivery and breast feeding practices across three settings. Both the demand and supply side factors have an important influence on practices. (author)

Waste Oils pre-Esterification for Biodiesel Synthesis: Effect of Feed Moisture Contents

OpenAIRE

Kalala Jalama

2012-01-01

A process flowsheet was developed in ChemCad 6.4 to study the effect of feed moisture contents on the pre-esterification of waste oils. Waste oils were modelled as a mixture of triolein (90%), oleic acid (5%) and water (5%). The process mainly consisted of feed drying, pre-esterification reaction and methanol recovery. The results showed that the process energy requirements would be minimized when higher degrees of feed drying and higher preesterification reaction tempera...

Application of ''Confirm tank T is an appropriate feed source for High-Level waste feed batch X'' to specific feed batches

International Nuclear Information System (INIS)

JO, J.

1999-01-01

This document addresses the characterization needs of tanks as set forth in the Data Quality Objectives for TWRS Privatization Phase I: Confirm Tank T is an Appropriate Feed Source for High-Level Waste Feed Batch X (Crawford et al. 1998). The primary purpose of this document is to collect existing data and identify the data needed to determine whether or not the feed source(s) are appropriate for a specific batch. To answer these questions, the existing tank data must be collected and a detailed review performed. If the existing data are insufficient to complete a full comparison, additional data must be obtained from the feed source(s). Additional information requirements need to be identified and formally documented, then the source tank waste must be sampled or resampled and analyzed. Once the additional data are obtained, the data shall be incorporated into the existing database for the source tank and a reevaluation of the data against the Data Quality Objective (DQO) must be made

Feed delivery method affects the learning of feeding and competitive behavior in dairy heifers.

Science.gov (United States)

Greter, A M; Leslie, K E; Mason, G J; McBride, B W; DeVries, T J

2010-08-01

bunk in the 2h following feed delivery (40.6 vs. 25.9 min/d). Heifers previously fed the TDR were displaced from the feed bunk more frequently than heifers previously fed the TMR (23.0 vs. 13.1 times/d), particularly during the 2-h period following feed delivery. Fecal scores were lower (more fluid in consistency) for heifers originally fed the TDR (3.2 vs. 3.7). The continued difference in feed bunk competition suggests that heifers previously fed the TDR had learned these patterns in the past, retaining them even when switched to an unfamiliar ration. Furthermore, lower fecal scores for heifers previously fed the TDR suggest altered rumen fermentation, possibly because of altered diurnal consumption patterns. These results show that feeding a TMR to replacement dairy heifers from a young age promotes a more even diurnal feeding pattern, minimizes feed bunk competition, and promotes a more solid fecal consistency. Copyright (c) 2010 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Assessment of Available Particle Size Data to Support an Analysis of the Waste Feed Delivery System Transfer System

International Nuclear Information System (INIS)

JEWETT, J.R.

2000-01-01

Available data pertaining to size distribution of the particulates in Hanford underground tank waste have been reviewed. Although considerable differences exist between measurement methods, it may be stated with 95% confidence that the median particle size does not exceed 275 (micro)m in at least 95% of the ten tanks selected as sources of HLW feed for Phase 1 vitrification in the RPP. This particle size is recommended as a design basis for the WFD transfer system

The use of food wastes as feed ingredients for culturing grass carp (Ctenopharyngodon idellus) in Hong Kong.

Science.gov (United States)

Choi, W M; Lam, C L; Mo, W Y; Wong, M H

2016-04-01

Different types of food wastes, e.g., meats, bones, cereals, fruits, and vegetables, were collected from hotels in Hong Kong, mixed in different ratio, and processed into feed pellets (food wastes (FWs) A, B, and C) for feeding trials in aquaculture species. Grass carp fed with cereal-dominant feed (FW A) showed the best growth (in terms of specific growth rate, relative weight gain, and protein efficiency ratio), among all food waste feeds. However, the growth rates of food waste groups especially the meat product-contained feeds (FW B and FW C) were lower than the commercial feed, Jinfeng(®) 613 formulation (control). The results indicated that grass carp utilized plant proteins better than animal proteins and preferred carbohydrate as a major energy source than lipid. The high-lipid content in feed containing meat products was also a possible reason for hindering growth and resulted high body lipid. It is suggested that lipid should be removed in the preparation of food waste feed or further investigations by implementing supplements, e.g., enzymes in feed to enhance lipid or protein utilization by fish. This utilization of food waste could be an effective and practical way to deal with these wastes in this densely populated city.

Feed Materials Production Center Waste Management Plan

International Nuclear Information System (INIS)

Watts, R.E.; Allen, T.; Castle, S.A.; Hopper, J.P.; Oelrich, R.L.

1986-01-01

In the process of producing uranium metal products used in Department of Energy (DOE) defense programs at other DOE facilities, various types of wastes are generated at the Feed Materials Production Center (FMPC). Process wastes, both generated and stored, are discussed in the Waste Management Plan and include low-level radioactive waste (LLW), mixed hazardous/radioactive waste, and sanitary/industrial waste. Scrap metal waste and wastes requiring special remediation are also addressed in the Plan. The Waste Management Plan identifies the comprehensive programs developed to address safe storage and disposition of all wastes from past, present, and future operations at the FMPC. Waste streams discussed in this Plan are representative of the waste generated and waste types that concern worker and public health and safety. Budgets and schedules for implementation of waste disposition are also addressed. The waste streams receiving the largest amount of funding include LLW approved for shipment by DOE/ORO to the Nevada Test Site (NTS) (MgF 2 , slag leach filter cake, and neutralized raffinate); remedial action wastes (waste pits, K-65 silo waste); thorium; scrap metal (contaminated and noncontaminated ferrous and copper scrap); construction rubble and soil generated from decontamination and decommissioning of outdated facilities; and low-level wastes that will be handled through the Low-Level Waste Processing and Shipping System (LLWPSS). Waste Management milestones are also provided. The Waste Management Plan is divided into eight major sections: Introduction; Site Waste and Waste Generating Process; Strategy; Projects and Operations; Waste Stream Budgets; Milestones; Quality Assurance for Waste Management; and Environmental Monitoring Program

Poultry feed based on protein hydrolysate derived from chrome-tanned leather solid waste: creating value from waste.

Science.gov (United States)

Chaudhary, Rubina; Pati, Anupama

2016-04-01

Leather industry generates huge amount of chrome-containing leather solid waste which creates major environment problems to tanners worldwide. Chrome-tanned leather solid waste is primarily chromium complex of collagen protein. The presence of chromium limits its protein application in animal feed industry. The purified protein hydrolysate with zero chromium could be used in poultry feed. In this study, an attempt has been made to assess performance of poultry with purified protein hydrolysate as a feed derived from chrome-tanned leather waste as partial replacement of soyabean meal as a sole source of protein for growing broiler chickens. Growth study was conducted to evaluate the effect of feeding protein hydrolysate on performance and physiochemical characteristics of meat of broiler chickens. Two experimental diets containing various levels of protein hydrolysate (EI-20 % and EII-30 %) were evaluated. The comparative study was performed as control with soyabean meal. Daily feed intake, body weight gain and feed conversion ratio were measured from day 8 to day 35. At the end of the study, birds were randomly selected and slaughtered to evaluate for physiochemical characteristics of meat. Diet had significant effects on feed intake and body weight gain. Birds fed with 20 and 30 % protein hydrolysate consumed 9.5 and 17.5 % higher amount of feed and gained 6.5 and 16.6 % higher than soyabean meal-fed birds. The current study produced evidence that protein hydrolysate can replace up to 75 % of soyabean meal in broiler diets without affecting either growth performance or meat characteristics.

Irradiated Palm Oil Waste (Sludge) As Feed Supplement For Nila Gift Fish (Oreochromis niloticus)

International Nuclear Information System (INIS)

MU, Jenny; PM, Adria

2002-01-01

The objective of the experiment was to study the fish weight development after being fed with irradiated palm oil waste pellet. Irradiated Palm oil waste pellet was produced from palm oil waste (sludge) with some additional materials, i.e. rice bran, fish powder, soybean powder, tapioca powder. The mixture was then irradiated with a dose of 4 kGy to decontaminate pathogen microbe and other contaminant microbes, the experiment have been carried out in 4 treatments. Treatment A was male fish which was being fed with irradiated sludge palm oil waste pellet and commercial pelletized feed (2:1), treatment C was female with the same feed as A, treatment B was male fish feed with commercial pelletized, treatment D was female fish with the same feed as B. Each treatment was placed in a pond. The feed with the amount of 3% of total body weight was given to the fishes 2 times per day. The result of this experiment showed that the male fish weight receiving treatment A and B were 195.37 g and 175.12 g. The female fish weight at treatments C and D were 170.28 g and 160.15 g, respectively. Data obtained from this experiment showed that the treatment of irradiated sludge palm oil waste pellet and commercial pelletized (2:1) were more efficient as fish feeding compared to commercial pellets

Hydrothermal treatment for inactivating some hygienic microbial indicators from food waste-amended animal feed.

Science.gov (United States)

Jin, Yiying; Chen, Ting; Li, Huan

2012-07-01

To achieve the hygienic safety of food waste used as animal feed, a hydrothermal treatment process of 60-110 degrees C for 10-60 min was applied on the separated food waste from a university canteen. Based on the microbial analysis of raw waste, the inactivation of hygienic indicators of Staphylococcus aureus (SA), total coliform (TC), total aerobic plate counts (TPC), and molds and yeast (MY) were analyzed during the hydrothermal process. Results showed that indicators' concentrations were substantially reduced after hydrothermal treatment, with a greater reduction observed when the waste was treated with a higher temperature and pressure and a longer ramping time. The 110 degrees C hydrothermal treatment for 60 min was sufficient to disinfect food waste as animal feed from the viewpoint of hygienic safety. Results obtained so far indicate that hydrothermal treatment can significantly decrease microbial indicators' concentrations but does not lead to complete sterilization, because MY survived even after 60 min treatment at 110 degrees C. The information from the present study will contribute to the microbial risk control of food waste-amended animal feed, to cope with legislation on food or feed safety.

Ecofeed, animal feed produced from recycled food waste.

Science.gov (United States)

Sugiura, Katsuaki; Yamatani, Shoich; Watahara, Masashi; Onodera, Takashi

2009-01-01

Due to the price hike of imported grains for feed, the production of Ecofeed, feed produced from recycled food waste, has increased in recent years. Food dregs from the food and beverage processing industry and out-of-date food from supermarkets and convenience stores are most often used as raw materials for Ecofeed. As food waste usually contains a lot of moisture and is easily spoiled, guidelines prescribing measures to be taken when collecting, transporting and storing raw materials, and for the production, shipment, storage and use of Ecofeed products, have been developed to ensure the safety of Ecofeed. The guidelines also include measures that should be taken to prevent the spread of bovine spongiform encephalopathy when producing and using Ecofeed. A certification system was introduced in March 2009 to ensure the quality and safety of Ecofeed and thus promote its use.

The waste minimization program at the Feed Materials Production Center

International Nuclear Information System (INIS)

Blasdel, J.E.; Crotzer, M.E.; Gardner, R.L.; Kato, T.R.; Spradlin, C.N.

1987-01-01

A waste minimization program is being implemented at the Feed Materials Production Center to reduce the generation of uranium-contaminated wastes and to comply with existing and forthcoming regulations. Procedures and plans are described which deal with process and non-process trash, contaminated wood and metals, used metal drums, and major process wastes such as contaminated magnesium fluoride and neutralized raffinate. Waste minimization techniques used include segregation, source reduction, volume reduction, material substitution and waste/product recycle. The importance of training, communication, and incentives is also covered. 5 refs., 11 figs

Project Delivery Acquisition and Contracting Plan for the Tank Farm Contractor

International Nuclear Information System (INIS)

MERCADO, L.C.

2000-01-01

This document is a plan presenting the process, strategies and approaches for vendor contracting by the Tank Farm Contractor. The plan focuses on contracting structures, practices, methods, and desired approaches in contracting. The U.S. Department of Energy (DOE), Office of River Protection (ORP) has contracted with the CH2M HILL Hanford Group, Inc. (CHG), as the Tank Farm Contractor (TFC), to support vitrification of Hanford Site tank waste by the Privatization Contractor. During Waste Feed Delivery Phase 1, waste will be retrieved from certain double-shell tanks and delivered to the Privatization Contractor to meet contract feed delivery requirements. Near-term project goals include upgrading infrastructure systems; retrieving and delivering the waste; and accepting the waste packages for interim onsite storage and disposal. Project Delivery includes individual projects assigned to provide the infrastructure and systems responsible to provide engineering, design, procurement, installation/construction, and testing/turnover of systems for retrieval of waste from Hanford double-shell tanks. This plan sets the requirements for projects work scope, contracting practices, structures, methods, and performance measurements. The plan is designed to integrate Life-Cycle Projects acquisitions and provide a consistent contracting approach. This effort will serve as a step improvement in contract reform implementing commercial practices into DOE projects

Ecofeed, animal feed produced from recycled food waste

Directory of Open Access Journals (Sweden)

Katsuaki Sugiura

2009-09-01

Full Text Available Due to the price hike of imported grains for feed, the production of Ecofeed, feed produced from recycled food waste, has increased in recent years. Food dregs from the food and beverage processing industry and out-of-date food from supermarkets and convenience stores are most often used as raw materials for Ecofeed. As food waste usually contains a lot of moisture and is easily spoiled, guidelines prescribing measures to be taken when collecting, transporting and storing raw materials, and for the production, shipment, storage and use of Ecofeed products, have been developed to ensure the safety of Ecofeed. The guidelines also include measures that should be taken to prevent the spread of bovine spongiform encephalopathy when producing and using Ecofeed. A certification system was introduced in March 2009 to ensure the quality and safety of Ecofeed and thus promote its use.

Increased Coal Replacement in a Cement Kiln Burner by Feeding a Mixture of Solid Hazardous Waste and Shredded Plastic Waste

OpenAIRE

Ariyaratne, W. K. Hiromi; Melaaen, Morten Christian; Tokheim, Lars-André

2013-01-01

The present study aims to find the maximum possible replacement of coal by combined feeding of plastic waste and solid hazardous waste mixed with wood chips (SHW) in rotary kiln burners used in cement kiln systems. The coal replacement should be achieved without negative impacts on product quality, emissions or overall operation of the process. A full-scale experiment was carried out in the rotary kiln burner of a cement kiln by varying SHW and plastic waste feeding rates. Experimental result...

The deep processing of seaweed industrial waste--Influence of several fermentation on seaweed waste of feed

Science.gov (United States)

Zhao, Shipeng; Zhang, Shuping

2018-02-01

This paper focuses on several factors on the effects of fermented seaweed feed, and obtains the optimal fermentation process through the analysis of nutrients. Through the experiment we can get, Seaweed waste fermented the best feed when adding 1% of microbial agents and 0.5% of corn powder, fermenting for 15 days.

Effect of feeding mode and dilution on the performance and microbial community population in anaerobic digestion of food waste.

Science.gov (United States)

Park, Jong-Hun; Kumar, Gopalakrishnan; Yun, Yeo-Myeong; Kwon, Joong-Chun; Kim, Sang-Hyoun

2018-01-01

The effect of feeding mode and dilution was studied in anaerobic digestion of food waste. An upflow anaerobic digester with a settler was fed at six different organic loading rates (OLRs) from 4.6 to 8.6kgCOD/m 3 /d for 200days. The highest methane productivity of 2.78LCH 4 /L/d was achieved at 8.6kgCOD/m 3 /d during continuous feeding of diluted FW. Continuous feeding of diluted food waste showed more stable and efficient performance than stepwise feeding of undiluted food waste. Sharp increase in propionate concentration attributed towards deterioration of the digester performances in stepwise feeding of undiluted food waste. Microbial communities at various OLRs divulged that the microbial distribution in the continuous feeding of diluted food waste was not significantly perturbed despite the increase of OLR up to 8.6kgCOD/m 3 /d, which was contrast to the unstable distribution in stepwise feeding of undiluted food waste at 6.1kgCOD/m 3 /d. Copyright © 2017 Elsevier Ltd. All rights reserved.

Recycle Waste Collection Tank (RWCT) simulant testing in the PVTD feed preparation system

International Nuclear Information System (INIS)

Abrigo, G.P.; Daume, J.T.; Halstead, S.D.; Myers, R.L.; Beckette, M.R.; Freeman, C.J.; Hatchell, B.K.

1996-03-01

(This is part of the radwaste vitrification program at Hanford.) RWCT was to routinely receive final canister decontamination sand blast frit and rinse water, Decontamination Waste Treatment Tank bottoms, and melter off-gas Submerged Bed Scrubber filter cake. In order to address the design needs of the RWCT system to meet performance levels, the PNL Vitrification Technology (PVTD) program used the Feed Preparation Test System (FPTS) to evaluate its equipment and performance for a simulant of RWCT slurry. (FPTS is an adaptation of the Defense Waste Processing Facility feed preparation system and represents the initially proposed Hanford Waste Vitrification Plant feed preparation system designed by Fluor-Daniel, Inc.) The following were determined: mixing performance, pump priming, pump performance, simulant flow characterization, evaporator and condenser performance, and ammonia dispersion. The RWCT test had two runs, one with and one without tank baffles

Analysis of the Potential Solid Waste Palm Oil as Animal Feed Cattle in Province Riau

OpenAIRE

Chalid, Nursiah; Flordeluna, Cattelya

2014-01-01

This study aims to identify and analyze the potential of solid waste as cattle feed in the Riau province where oil palm solid waste is estimated each year has increased the amount of solid waste production as the increasing production of fresh fruit bunches ( FFB ) is in if every year .The data used in this study are primary and secondary data . The method used in this peneilitan is descriptive method . To see the right strategy in the potential of oil palm solid waste as cattle feed in the p...

Investigation of the available technologies and their feasibility for the conversion of food waste into fish feed in Hong Kong.

Science.gov (United States)

Cheng, Jack Y K; Lo, Irene M C

2016-04-01

Food waste is the largest constituent of municipal solid waste in Hong Kong, but food waste recycling is still in its infancy. With the imminent saturation of all landfill sites by 2020, multiple technologies are needed to boost up the food waste recycling rate in Hong Kong. Conversion of food waste into animal feeds is prevalent in Japan, South Korea, and Taiwan, treating over 40 % of their recycled food waste. This direction is worth exploring in Hong Kong once concerns over food safety are resolved. Fortunately, while feeding food waste to pigs and chickens poses threats to public health, feeding it to fish is considered low risk. In order to examine the feasibility of converting food waste into fish feed in Hong Kong, this paper investigates the market demand, technical viability, feed quality, regulatory hurdles, and potential contribution. The results show that a significant amount of food waste can be recycled by converting it into fish feed due to the enormous demand from feed factories in mainland China. Two conversion technologies, heat drying and black soldier fly bioconversion, are studied extensively. Black soldier fly bioconversion is preferable because the end-product, insect powder, is anticipated to gain import approval from mainland China. The authors suggest further research efforts to speed up its application for food waste recycling in urban cities.

Valorisation of food waste to produce new raw materials for animal feed.

Science.gov (United States)

San Martin, D; Ramos, S; Zufía, J

2016-05-01

This study assesses the suitability of vegetable waste produced by food industry for use as a raw material for animal feed. It includes safety and nutritional viability, technical feasibility and environmental evaluation. Vegetable by-products were found to be nutritionally and sanitarily appropriate for use in animal feed. The drying technologies tested for making vegetable waste suitable for use in the animal feed market were pulse combustion drying, oven and microwave. The different meal prototypes obtained were found to comply with all the requirements of the animal feed market. An action plan that takes into account all the stages of the valorisation process was subsequently defined in agreement with local stakeholders. This plan was validated in a pilot-scale demonstration trial. Finally, the technical feasibility was studied and environmental improvement was performed. This project was funded by the European LIFE+ program (LIFE09 ENV/ES/000473). Copyright © 2015 Elsevier Ltd. All rights reserved.

Feasibility analysis of constant TRU feeding in waste transmutation system using accelerator-driven subcritical system

Energy Technology Data Exchange (ETDEWEB)

Lee, Kun Jai; Cho, Nam Zin; Jo, Chang Keun; Park, Chang Je; Kim, Do Sam; Park, Jeong Hwan [Korea Advanced Institute of Science and Technology, Taejon (Korea)

1999-03-01

It is probable that the issue of nuclear spent fuel and high-level waste can have negative impact on the future expansion of nuclear power programs. Accelerator-driven nuclear waste transmutation with constant composition TRU feeding which satisfies non-proliferation condition will help establish the long-range nuclear waste disposal strategy. In this study, current status of accelerator-driven transmutation of waste technology, and feasibility analysis of constant composition TRU feeding system were investigated. We ascertained that solid system using constant composition TRU is feasible with the the capability of transmutation. (author). 13 refs., 53 figs., 20 tabs.

Hanford Waste Vitrification Plant full-scale feed preparation testing with water and process simulant slurries

International Nuclear Information System (INIS)

Gaskill, J.R.; Larson, D.E.; Abrigo, G.P.

1996-03-01

The Hanford Waste Vitrification Plant was intended to convert selected, pretreated defense high-level waste and transuranic waste from the Hanford Site into a borosilicate glass. A full-scale testing program was conducted with nonradioactive waste simulants to develop information for process and equipment design of the feed-preparation system. The equipment systems tested included the Slurry Receipt and Adjustment Tank, Slurry Mix Evaporator, and Melter-Feed Tank. The areas of data generation included heat transfer (boiling, heating, and cooling), slurry mixing, slurry pumping and transport, slurry sampling, and process chemistry. 13 refs., 129 figs., 68 tabs

Decision Document for Heat Removal from High-Level Waste Tanks

International Nuclear Information System (INIS)

WILLIS, W.L.

2000-01-01

This document establishes the combination of design and operational configurations that will be used to provide heat removal from high-level waste tanks during Phase 1 waste feed delivery to prevent the waste temperature from exceeding tank safety requirement limits. The chosen method--to use the primary and annulus ventilation systems to remove heat from the high-level waste tanks--is documented herein

Bioprocessing papaya processing waste for potential aquaculture feed supplement--economic and nutrient analysis with shrimp feeding trial.

Science.gov (United States)

Kang, H Y; Yang, P Y; Dominy, W G; Lee, C S

2010-10-01

Papaya processing waste (PPW), a major fruit processing waste in the Hawaii islands, served as substrate for yeast (Saccharomyces cerevisiae) growth. The fermented PPW products containing nutrients of 45% crude protein and various fat, fiber, lignin, cellulose, and minerals were advantages to nutrients of yeast alone. Three experimental diets controlled at 35% protein formulation containing different levels of inclusion of PPW products and a commercial control diet were fed to shrimps for 8 weeks. The 50% inclusion of PPW diets were comparable to commercial feed in weight, growth, feed conversion ratio (FCR) and survival rate. Such bioprocess treatment system would be economically feasible with the control of annual cost and increase of the amount of PPW treated. The selling price of PPW products and annual operation and maintenance cost were the most influential factors to additional profits. This study presented a promising alternative for environmental-friendly treatment of organic wastes as well as the sustainability of local agriculture and aquaculture industries. Copyright © 2010 Elsevier Ltd. All rights reserved.

Formulation of a fish feed for goldfish with natural astaxanthin extracted from shrimp waste.

Science.gov (United States)

Weeratunge, W K O V; Perera, B G K

2016-01-01

Astaxanthin is a xanthophyll carotenoid, which exhibits many important biological activities including a high degree of antioxidant capacity (AOC) and antibacterial activity, hence has a significant applicability in food, pharmaceutical and cosmetic industries. An attempt was made towards optimization of astaxanthin extraction conditions using three different extraction conditions and a solvent series, from uncooked, cooked and acid-treated shrimp waste, which is a readily available and cheap source of the pigment. The astaxanthin extracts were analyzed by comparing their UV-visible absorbance spectra and thin layer chromatograms with a standard astaxanthin sample. The percentage of astaxanthin in each crude sample was determined using the Beer-Lambert law. The Folin-Ciocalteu assay and the disk diffusion assay were used to investigate the antioxidant capacities and antibacterial activities of extracted astaxanthin samples respectively. The extracted astaxanthin was incorporated into fish feeds to test its ability to enhance the skin color of goldfish. The best astaxanthin percentage of 68 % was observed with the acetone:ethyl acetate (1:1) solvent system facilitated by maceration of cooked and acid treated shrimp, whereas the best crude yield of 33 % was found to be in the acetone extract of the acid-treated shrimp sample. The highest AOC of 65 µg pyrogallol equivalents/mg was observed for the EtOAc extract obtained by maceration of acid-treated shrimp waste. The highest AOC by sonication and soxhlet extraction methods were also obtained with the EtOAc solvent. The extracts exhibited antibacterial activity against four selected bacterial strains. The newly formulated astaxanthin enriched fish feed was economical and indicated a significant improvement of the skin color and healthiness of goldfish compared to the control feeds. Biologically active astaxanthin can be successfully extracted from shrimp waste in higher percentages. The extraction technique and the

Preliminary Assessment of the Hanford Tank Waste Feed Acceptance and Product Qualification Programs

Energy Technology Data Exchange (ETDEWEB)

Herman, C. C.; Adamson, Duane J.; Herman, D. T.; Peeler, David K.; Poirier, Micheal R.; Reboul, S. H.; Stone, M. E.; Peterson, Reid A.; Chun, Jaehun; Fort, James A.; Vienna, John D.; Wells, Beric E.

2013-04-01

The U.S. Department of Energy Office of Environmental Management (EM) is engaging the national laboratories to provide the scientific and technological rigor to support EM program and project planning, technology development and deployment, project execution, and assessment of program outcomes. As an early demonstration of this new responsibility, Savannah River National Laboratory (SRNL) and Pacific Northwest National Laboratory (PNNL) have been chartered to implement a science and technology program addressing Hanford Tank waste feed acceptance and product qualification. As a first step, the laboratories examined the technical risks and uncertainties associated with the planned waste feed acceptance and qualification testing for Hanford tank wastes. Science and technology gaps were identified for work associated with 1) feed criteria development with emphasis on identifying the feed properties and the process requirements, 2) the Tank Waste Treatment and Immobilization Plant (WTP) process qualification program, and 3) the WTP HLW glass product qualification program. Opportunities for streamlining the accetpance and qualification programs were also considered in the gap assessment. Technical approaches to address the science and technology gaps and/or implement the opportunities were identified. These approaches will be further refined and developed as strong integrated teams of researchers from national laboratories, contractors, industry, and academia are brought together to provide the best science and technology solutions. Pursuing the identified approaches will have immediate and long-term benefits to DOE in reducing risks and uncertainties associated with tank waste removal and preparation, transfers from the tank farm to the WTP, processing within the WTP Pretreatment Facility, and in producing qualified HLW glass products. Additionally, implementation of the identified opportunities provides the potential for long-term cost savings given the anticipated

Vermiconversion of paper waste by earthworm born and grown in the waste-fed reactors compared to the pioneers raised to adulthood on cowdung feed.

Science.gov (United States)

Gajalakshmi, S; Abbasi, S A

2004-08-01

The performance of four species of earthworm--Eudrilus eugeniae, Kinberg, Drawida willsi Michaelsen, Lampito mauritii, Kinberg and Perionyx excavatus, Perrier--born and grown in vermireactors fed with paper waste was studied over six months, in terms of vermicast output per unit feed, production of offspring, and increase in worm zoomass. These were compared with the performance of the previous generation which had been raised to adulthood on cowdung as principal feed before shifting them to vermireactors operating on cowdung-spiked paper waste. The results indicated that except with D. willsi of which the second generation performed only a shade better than the first, there was significant improvement in vermicast output, animal growth, and reproduction in the second generation compared to the first. The results indicated that cowdung-spiked paper waste can be an adequate food for successive generations of earthworms and that reactors can be operated indefinitely on this feed. The results also indicated that the earthworm generations born and raised in vermireactors operated on this feed become better vermiconverters of this feed than the parent earthworms.

HIERARCHIAL DESIGN AND EVALUATION OF PROCESSES TO GENERATE WASTE-RECYCLED FEEDS

Science.gov (United States)

Hierarchical Design and Evaluation of Processes to Generate Waste-Recycled FeedsRaymond L. SmithU.S. Environmental Protection AgencyOffice of Research and DevelopmentNational Risk Management Research Laboratory26 W. Martin Luther King DriveCincinna...

Effect of feeding system and fermented sago waste on performance of broiler chicken

Directory of Open Access Journals (Sweden)

I Putu Kompiang

2001-03-01

Full Text Available An experiment, with a split plot experimental design, was conducted to determine the effect of feeding system (full vs choice feeding and fermented sago waste (AST 5 vs 0% on the performance of broiler chickens. Complete feed was formulated tocontain 21% crude protein, 2900 kcal ME/kg, without or with 5% AST. Feed for choice feeding was formulated to contain 2900 kcal ME/kg, without or with 5% AST with crude protein 23 or 17%. Four hundreds DOC broilers were used for each treatment divided into 4 replicates (100 birds/replicate on litter system. Feed and water were given ad lib. during the 4 weeks trial. Data collected included feed consumption (weekly, body weight (bi-weekly, feed conversion ratio (FCR and protein efficiency ratio (PER were calculated biweekly. Feeding system has no significant effect on total feed/energy consumption. Choice feeding reduced total protein consumption (P<0.01; 323.5 vs 354.9 gram/head/4weeks, increased body weight gained (P<0.01; 889.5 vs 835 gram/head/4weeks, improved FCR (P<0.05; 1.90 vs 2.03, and PER (P<0.001; 0.37 vs 0.43. Fermented sago waste (AST had no significant effect on total feed/energy consumption (P<0.05, reduced total protein consumption (P<0.05; 333.6 vs 349.8 gram/head/4weeks, increased body weight gained (P<0.05; 887.5 vs 837 gram/head/4weeks, improved FCR (P<0.05; 1.88 vs 2.06 and PER (P<0.05; 0.38 vs 0.42. It is concluded that broiler chicken had an ability to determine its protein requirement, and AST supplementation significantly improved performance of the birds.

Pineapple waste-silages as basal feed for growing Boer X Kacang cross goats

Directory of Open Access Journals (Sweden)

Simon P Ginting

2007-10-01

Full Text Available The study was aimed: 1 to evaluate the effects of using different additives on the quality of pineapple waste-silage (SLN, and 2 to investigate the responses of goats fed with PAS as a basal feed. Pineapple processing wastes include skins and the pulp left after cannery wastes are pressed to extract the juice. Six additive treatments were used in the processing of pressed pineapple wastes, namely 1 urea (5% DM, 2 Urea (2% DM and cassava meal (3% DM, 3 molasses (5% DM, 4 urea (2.5% DM and molasses (2.5% DM, 5 fermented-juice lactic acid bacteria (5% DM, and 6 without additives. Fermentation periode were set at 9, 12, 15, 18 and 21 days. The best SLN obtained from those treatments was then used in feeding trials. Twenty male Boer x Kacang crosses with an initial body weight averaging 13.2 ± 1.9 kg were used in this experiment. The animals were allocated to one of the following feed treatments, in DM: A Grasses (75% + SLN (25%, B SLN (75% + Concentrates (25%, C SLN (50% +Concentrate (50%, and D SLN (25% + Concentrates (75%. Using molasses as additive material at 5% and 15 days of fermentation period gave the best chemical and physical characteristics of the SLN. Its crude fiber content decreased and it showed the lowest pH (4.7 The silage showed temperature at 280C, and its taste was sour, and no fungi contamination. The DM and OM intakes and DM, OM and N digestibility were not different (P>0.05 between the animals fed 75% Grass/25% CON and 75% SLN/25% CON. When the proportion of concentrates in the rations was increased, the feed intake and digestibility were increase significantly (P<0.05. ADG (71.3 vs 68.8 g and feed efficiency (11.2 vs 13.4 was similar between the 75% Grass/25% CON and 75% SLN 25% CON groups. ADG increased significantly (P<0.05 when the proportion of concentrates in ration was increased to 50% (82.6 g or to 75% (89.1 g. N retention was positive in all treatments, and it was increased significantly (P<0.05 as the proportion of

Remotely replaceable fuel and feed nozzles for the new waste calcining facility calciner vessel

International Nuclear Information System (INIS)

Fletcher, R.D.; Carter, J.A.; May, K.W.

1978-01-01

The development and testing of remotely replaceable fuel and feed nozzles for calcination of liquid radioactive wastes in the calciner vessel of the New Waste Calcining Facility being built at the Idaho National Engineering Laboratory is described. A complete fuel nozzle assembly was fabricated and tested at the Remote Maintenance Development Facility to evolve design refinements, identify required support equipment, and develop handling techniques. The design also provided for remote replacement of the nozzle support carriage and adjacent feed and fuel pipe loops using two pairs of master-slave manipulators

Noble metal behavior during melting of simulated high-level nuclear waste glass feeds

International Nuclear Information System (INIS)

Anderson, L.D.; Dennis, T.; Elliott, M.L.; Hrma, P.

1993-04-01

Noble metals and their oxides can settle in waste glass melters and cause electrical shorting. Simulated waste feeds from Hanford, Savannah River, and Germany were heat treated for 1 hour in a gradient furnace at temperatures ranging from approximately 600 degrees C--1000 degrees C and examined by electron microscopy to determine shapes, sizes, and distribution of noble metal particles as a function of temperature. Individual noble metal particles and agglomerates of rhodium (Rh), ruthenium (RuO 2 ), and palladium (Pd), as well as their alloys, were seen. the majority of particles and agglomerates were generally less than 10 microns; however, large agglomerations (up to 1 mm) were found in the German feed. Detailed particle distribution and characterization was performed for a Hanford waste to provide input to computer modeling of particle settling in the melter

A safety analysis of food waste-derived animal feeds from three typical conversion techniques in China.

Science.gov (United States)

Chen, Ting; Jin, Yiying; Shen, Dongsheng

2015-11-01

This study was based on the food waste to animal feed demonstration projects in China. A safety analysis of animal feeds from three typical treatment processes (i.e., fermentation, heat treatment, and coupled hydrothermal treatment and fermentation) was presented. The following factors are considered in this study: nutritive values characterized by organoleptic properties and general nutritional indices; the presence of bovine- and sheep-derived materials; microbiological indices for Salmonella, total coliform (TC), total aerobic plate counts (TAC), molds and yeast (MY), Staphylococcus Aureus (SA), and Listeria; chemical contaminant indices for hazardous trace elements such as Cr, Cd, and As; and nitrite and organic contaminants such as aflatoxin B1 (AFB1) and hexachlorocyclohexane (HCH). The present study reveals that the feeds from all three conversion processes showed balanced nutritional content and retained a certain feed value. The microbiological indices and the chemical contaminant indices for HCH, dichlorodiphenyltrichloroethane (DDT), nitrite, and mercury all met pertinent feed standards; however, the presence of bovine- and sheep-derived materials and a few chemical contaminants such as Pb were close to or might exceed the legislation permitted values in animal feeding. From the view of treatment techniques, all feed retained part of the nutritional values of the food waste after the conversion processes. Controlled heat treatment can guarantee the inactivation of bacterial pathogens, but none of the three techniques can guarantee the absence of cattle- and sheep-derived materials and acceptable levels of certain contaminants. The results obtained in this research and the feedstuffs legislation related to animal feed indicated that food waste-derived feed could be considered an adequate alternative to be used in animal diets, while the feeding action should be changed with the different qualities of the products, such as restrictions on the application

Use of slaughter house waste as a feed for shrimps and prawns

Digital Repository Service at National Institute of Oceanography (India)

Sumitra-Vijayaraghavan; Royan, J.P.; Krishnakumari, L.

Feeding experiments with some shrimps and fishes (Metapenaeus monoceros, Metapenaeus dobsoni, Sarotherodon mossambicus and Etroplus suratensis) using slaughter house waste as food, showed that the shrimps and arotherodon were able to utilize...

Impacts of waste from concentrated animal feeding operations on water quality

Science.gov (United States)

Burkholder, J.; Libra, B.; Weyer, P.; Heathcote, S.; Kolpin, D.; Thorne, P.S.; Wichman, M.

2007-01-01

Waste from agricultural livestock operations has been a long-standing concern with respect to contamination of water resources, particularly in terms of nutrient pollution. However, the recent growth of concentrated animal feeding operations (CAFOs) presents a greater risk to water quality because of both the increased volume of waste and to contaminants that may be present (e.g., antibiotics and other veterinary drugs) that may have both environmental and public health importance. Based on available data, generally accepted livestock waste management practices do not adequately or effectively protect water resources from contamination with excessive nutrients, microbial pathogens, and pharmaceuticals present in the waste. Impacts on surface water sources and wildlife have been documented in many agricultural areas in the United States. Potential impacts on human and environmental health from long-term inadvertent exposure to water contaminated with pharmaceuticals and other compounds are a growing public concern. This workgroup, which is part of the Conference on Environmental Health Impacts of Concentrated Animal Feeding Operations: Anticipating Hazards-Searching for Solutions, identified needs for rigorous ecosystem monitoring in the vicinity of CAFOs and for improved characterization of major toxicants affecting the environment and human health. Last, there is a need to promote and enforce best practices to minimize inputs of nutrients and toxicants from CAFOs into freshwater and marine ecosystems.

Hanford Tank Farms Waste Feed Flow Loop Phase VI: PulseEcho System Performance Evaluation

Energy Technology Data Exchange (ETDEWEB)

Denslow, Kayte M.; Bontha, Jagannadha R.; Adkins, Harold E.; Jenks, Jeromy WJ; Hopkins, Derek F.

2012-11-21

This document presents the visual and ultrasonic PulseEcho critical velocity test results obtained from the System Performance test campaign that was completed in September 2012 with the Remote Sampler Demonstration (RSD)/Waste Feed Flow Loop cold-test platform located at the Monarch test facility in Pasco, Washington. This report is intended to complement and accompany the report that will be developed by WRPS on the design of the System Performance simulant matrix, the analysis of the slurry test sample concentration and particle size distribution (PSD) data, and the design and construction of the RSD/Waste Feed Flow Loop cold-test platform.

A summary report on feed preparation offgas and glass redox data for Hanford waste vitrification plant: Letter report

International Nuclear Information System (INIS)

Merz, M.D.

1996-03-01

Tests to evaluate feed processing options for the Hanford Waste Vitrification Plant (HWVP) were conducted by a number of investigators, and considerable data were acquired for tests of different scale, including recent full-scale tests. In this report, a comparison was made of the characteristics of feed preparation observed in tests of scale ranging from 57 ml to full-scale of 28,000 liters. These tests included Pacific Northwest Laboratory (PNL) laboratory-scale tests, Kernforschungszentrums Karlsruhe (KfK) melter feed preparation, Research Scale Melter (RSM) feed preparation, Integrated DWPF Melter System (IDMS) feed preparation, Slurry Integrated Performance Testing (SIPT) feed preparation, and formic acid addition to Hanford Neutralized Current Acid Waste (NCAW) care samples.' The data presented herein were drawn mainly from draft reports and include system characteristics such as slurry volume and depth, sweep gas flow rate, headspace, and heating and stirring characteristics. Operating conditions such as acid feed rate, temperature, starting pH, final pH, quantities and type of frit, nitrite, nitrate, and carbonate concentrations, noble metal content, and waste oxide loading were tabulated. Offgas data for CO 2 , NO x , N 2 O, NO 2 , H 2 and NH 3 were tabulated on a common basis. Observation and non-observation of other species were also noted

Radiation induced chemical changes in and disinfection of organic wastes suitable for supplemental feed

International Nuclear Information System (INIS)

Groneman, A.F.

1980-01-01

Ionizing radiation has been found to disinfect organic wastes and simultaneously ease the separation of suspended solids from water. Because these effects can have important favourable impacts on the technology of upgrading organic wastes to animal feed or fertilizers, experimental studies are reported on the rationale of effects of gamma irradiation or disinfection and separation of the solid and the liquid phase of organic waste systems. The radiation inactivation of microorganisms occurs by direct and indirect action. Mechanisms of inactivation are discussed and measures are proposed how the indirect action of the radiation inactivation of microorganisms can be increased. Effects of gamma irradiation on dewatering properties of organic wastes were indirectly caused by the oxidizing OH radicals produced by the irradiation of water. OH radicals react with organic components of the solid phase which leads to their solubilisation resulting in an increase of the total organic carbon concentration in the liquid phase. Results of a mutagenicity test indicate that the solvated compounds exhibited no mutagenic activity. Microbiological case studies on the disinfection and upgrading of liquid and solid organic wastes to animal feed are discussed and the acceptance of radiation processing is evaluated. (Auth.)

2020 Vision for Tank Waste Cleanup (One System Integration) - 12506

Energy Technology Data Exchange (ETDEWEB)

Harp, Benton; Charboneau, Stacy; Olds, Erik [US DOE (United States)

2012-07-01

The mission of the Department of Energy's Office of River Protection (ORP) is to safely retrieve and treat the 56 million gallons of Hanford's tank waste and close the Tank Farms to protect the Columbia River. The millions of gallons of waste are a by-product of decades of plutonium production. After irradiated fuel rods were taken from the nuclear reactors to the processing facilities at Hanford they were exposed to a series of chemicals designed to dissolve away the rod, which enabled workers to retrieve the plutonium. Once those chemicals were exposed to the fuel rods they became radioactive and extremely hot. They also couldn't be used in this process more than once. Because the chemicals are caustic and extremely hazardous to humans and the environment, underground storage tanks were built to hold these chemicals until a more permanent solution could be found. The Cleanup of Hanford's 56 million gallons of radioactive and chemical waste stored in 177 large underground tanks represents the Department's largest and most complex environmental remediation project. Sixty percent by volume of the nation's high-level radioactive waste is stored in the underground tanks grouped into 18 'tank farms' on Hanford's central plateau. Hanford's mission to safely remove, treat and dispose of this waste includes the construction of a first-of-its-kind Waste Treatment Plant (WTP), ongoing retrieval of waste from single-shell tanks, and building or upgrading the waste feed delivery infrastructure that will deliver the waste to and support operations of the WTP beginning in 2019. Our discussion of the 2020 Vision for Hanford tank waste cleanup will address the significant progress made to date and ongoing activities to manage the operations of the tank farms and WTP as a single system capable of retrieving, delivering, treating and disposing Hanford's tank waste. The initiation of hot operations and subsequent full operations

Noble metal behavior during melting of simulated high-level nuclear waste glass feeds

International Nuclear Information System (INIS)

Anderson, L.D.; Dennis, T.; Elliott, M.L.; Hrma, P.

1994-01-01

Noble metals and their oxides can settle in waste glass melters and cause electrical shorting. Simulate waste feeds from Hanford, Savannah River, and Kernforschungszentrum Karlsruhe were heat treated for 1 hour in a gradient furnace at temperatures ranging from approximately 600 degrees C to 1000 degrees C and examined by electron microscopy to determine shapes, sizes, and distribution of noble metal particles as a function of temperature. Individual noble metal particles and agglomerates of rhodium (Rh), ruthenium (RuO 2 ), and palladium (Pd), as well as their alloys, were seen. The majority of particles and agglomerates were generally less than 10 μm; however, large agglomerations (up to 1 mm) were found in the German feed. 5 refs., 6 figs., 2 tabs

Infant feeding practices among mildly wasted children: a retrospective study on Nias Island, Indonesia

Directory of Open Access Journals (Sweden)

Inayati Dyah

2012-03-01

Full Text Available Abstract Background This study investigated the infant feeding practices of participating mothers who were recruited into a research project aimed at improving the nutritional status of mildly wasted children (-scores aged ≥ 6 to Methods Cross-sectional, questionnaire-based interview of mothers of the index children (n = 215 who were admitted to the community program for mildly wasted children in the study area. Four focus groups and twenty in-depth interviews were conducted to explore further information on infant feeding practices in the study area. Results Retrospective results indicated that 6% of the mothers never breastfed. Fifty two percent of mothers initiated breastfeeding within six hours of birth, but 17% discarded colostrum. Exclusive breastfeeding until 6 months of age was practiced by 12%. Seventy-four percent of the mothers offered supplementary liquids besides breast milk within the first 7 days of life, and 14% of infants received these supplementary liquids from 7 days onwards until 6 months of age. Moreover, 79% of the infants were given complementary foods (solid, semi-solid, or soft foods before 6 months of age. About 9% of the children were breastfed at least two years. Less than one in five of the mildly wasted children (19% were breastfed on admission to the community program. Qualitative assessments found that inappropriate infant feeding practices were strongly influenced by traditional beliefs of the mothers and paternal grandmothers in the study areas. Conclusion Generally, suboptimal infant feeding was widely practiced among mothers of mildly wasted children in the study area on Nias Island, Indonesia. To promote breastfeeding practices among mothers on Nias Island, appropriate nutrition training for community workers and health-nutrition officers is needed to improve relevant counseling skills. In addition, encouraging public nutrition education that promotes breastfeeding, taking into account social

A study of waste and delivery valve design modification to the pump performance

Science.gov (United States)

Harith, M. N.; Bakar, R. A.; Ramasamy, D.; Kardigama, K.; Quanjin, Ma

2018-04-01

This paper objective is to share design revolution of waste and delivery valve that contribute to the overall pump performance. In this paper, 3 new designs of waste and delivery valve pump are presented with comprehensive internal flow analysis using computational fluid dynamics (CFD) simulation over 4 cases that have been deeply study for one of the design chosen. 4 cases involving opening and closing both valve or either one. 0.265m height size of customized waste valve with an opening limiter and spring was used to demonstrate cyclic closing and opening valve operation extended up to 0.164m gap. Based on result, this characteristics contribute to 10-20% waste water reduction and enhancement of flow rate height up to 80m. Apart from that this paper also share some of pressure (dynamic, total, static), velocity (x, y, z axis) simulation including the vector flow were under different flow cases.

Livestock Feed Production from Sago Solid Waste by Pretreatment and Anaerobic Fermentation Process

Directory of Open Access Journals (Sweden)

Sumardiono Siswo

2018-01-01

Full Text Available Food needs in Indonesia is increasing, including beef. Today, Indonesia has problem to do self-sufficiency in beef. The cause of the problem is the quality of local beef is still lower compared with imported beef due to the quality of livestock feed consumed. To increase the quality of livestock is through pretreatment and fermentation. Source of livestock feed that processed is solid sago waste (Arenga microcarpa, because in Indonesia that is relatively abundant and not used optimally. Chemical pretreatment process for delignification is by using NaOH solution. The purposes of this research are to study NaOH pretreatment, the addition of Trichoderma sp, and fermentation time to improve the quality of sago solid waste as livestock feed through anaerobic fermentation. The variables used are addition or without addition (4%w NaOH solution and Trichoderma sp 1%w and fermentation time (7, 14 and 21 days, with the response of crude fiber and protein. The result of this research shows that the pretreatment with soaking of NaOH solution, addition of Trichoderma sp and 14 days of fermentation was more effective to improve the quality of solid sago waste with decrease of crude fiber from 33.37% to 17.36% and increase of crude protein from 4.00% to 7.96%.

Double Shell Tank (DST) Process Waste Sampling Subsystem Definition Report

International Nuclear Information System (INIS)

RASMUSSEN, J.H.

2000-01-01

This report defines the Double-Shell Tank (DST) Process Waste Sampling Subsystem (PWSS). This subsystem definition report fully describes and identifies the system boundaries of the PWSS. This definition provides a basis for developing functional, performance, and test requirements (i.e., subsystem specification), as necessary, for the PWSS. The resultant PWSS specification will include the sampling requirements to support the transfer of waste from the DSTs to the Privatization Contractor during Phase 1 of Waste Feed Delivery

Waste volume reduction factors for potential 242-A evaporator feed

International Nuclear Information System (INIS)

Sederburg, J.P.

1995-01-01

Double-shell tank (DST) storage space requirements have been shown to be highly dependent on the end point of 242-A operations. Consequences to the DST of various waste volumes, and concentrations, are evaluated. Only waste streams that are currently planned to be stored in the DST system before the year 2004 are discussed. As of January 1, 1995, approximately 27-million L (7.2-million gal) of dilute wastes are stored in the DSTs available for evaporator processing. Waste streams planned to be transferred to the DSTs before December 31, 2004, are identified. The DST volume for storing slurry from these wastes is presented in this document. At a final slurry specific gravity of -1.35, 22.5-million L (5.93-million gal) of DST space would be needed on December 31, 2004, to store the product from evaporator processing of these feedstocks. The expected volume needed if the resultant slurry were concentrated to the traditional double-shell slurry feed (DSSF) phase boundary (a specific gravity of ∼1.5) would be 17.7-million L (4.67-million gal). An additional 4.8-million L (1.26-million gal) is therefore needed if these wastes are concentrated to a specific gravity of 1.35 instead of the DSSF limit

Phase Equilibrium Studies of Savannah River Tanks and Feed Streams for the Salt Waste Processing Facility

Energy Technology Data Exchange (ETDEWEB)

Weber, C.F.

2001-06-19

A chemical equilibrium model is developed and used to evaluate supersaturation of tanks and proposed feed streams to the Salt Waste Processing Facility. The model uses Pitzer's model for activity coefficients and is validated by comparison with a variety of thermodynamic data. The model assesses the supersaturation of 13 tanks at the Savannah River Site (SRS), indicating that small amounts of gibbsite and or aluminosilicate may form. The model is also used to evaluate proposed feed streams to the Salt Waste Processing Facility for 13 years of operation. Results indicate that dilutions using 3-4 M NaOH (about 0.3-0.4 L caustic per kg feed solution) should avoid precipitation and reduce the Na{sup +} ion concentration to 5.6 M.

The German bakery waste incident; use of a combined approach of screening and confirmation for dioxins in feed and food

NARCIS (Netherlands)

Hoogenboom, L.A.P.; Bovee, T.F.H.; Portier, L.; Weg, van der G.; Onstenk, C.G.M.; Traag, W.A.

2004-01-01

During the last six years several incidents have occurred with dioxins in feed, stressing the need for rapid screening methods for these compounds. The most recent incident was the contamination of bakery waste used for animal feed due to the use of waste wood for drying of the material. In addition

PHYSICAL CHARACTERIZATION OF VITREOUS STATE LABORATORY AY102/C106 AND AZ102 HIGH LEVEL WASTE MELTER FEED SIMULANTS (U)

Energy Technology Data Exchange (ETDEWEB)

Hansen, E

2005-03-31

The objective of this task is to characterize and report specified physical properties and pH of simulant high level waste (HLW) melter feeds (MF) processed through the scaled melters at Vitreous State Laboratories (VSL). The HLW MF simulants characterized are VSL AZ102 straight hydroxide melter feed, VSL AZ102 straight hydroxide rheology adjusted melter feed, VSL AY102/C106 straight hydroxide melter feed, VSL AY102/C106 straight hydroxide rheology adjusted melter feed, and Savannah River National Laboratory (SRNL) AY102/C106 precipitated hydroxide processed sludge blended with glass former chemicals at VSL to make melter feed. The physical properties and pH were characterized using the methods stated in the Waste Treatment Plant (WTP) characterization procedure (Ref. 7).

WTP Waste Feed Qualification: Hydrogen Generation Rate Measurement Apparatus Testing Report

Energy Technology Data Exchange (ETDEWEB)

Stone, M. E. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Newell, J. D. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Smith, T. E. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Pareizs, J. M. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

2016-06-01

The generation rate of hydrogen gas in the Hanford tank waste will be measured during the qualification of the staged tank waste for processing in the Hanford Tank Waste Treatment and Immobilization Plant. Based on a review of past practices in measurement of the hydrogen generation, an apparatus to perform this measurement has been designed and tested for use during waste feed qualification. The hydrogen generation rate measurement apparatus (HGRMA) described in this document utilized a 100 milliliter sample in a continuously-purged, continuously-stirred vessel, with measurement of hydrogen concentration in the vent gas. The vessel and lid had a combined 220 milliliters of headspace. The vent gas system included a small condenser to prevent excessive evaporative losses from the sample during the test, as well as a demister and filter to prevent particle migration from the sample to the gas chromatography system. The gas chromatograph was an on line automated instrument with a large-volume sample-injection system to allow measurement of very low hydrogen concentrations. This instrument automatically sampled the vent gas from the hydrogen generation rate measurement apparatus every five minutes and performed data regression in real time. The fabrication of the hydrogen generation rate measurement apparatus was in accordance with twenty three (23) design requirements documented in the conceptual design package, as well as seven (7) required developmental activities documented in the task plan associated with this work scope. The HGRMA was initially tested for proof of concept with physical simulants, and a remote demonstration of the system was performed in the Savannah River National Laboratory Shielded Cells Mockup Facility. Final verification testing was performed using non-radioactive simulants of the Hanford tank waste. Three different simulants were tested to bound the expected rheological properties expected during waste feed qualification testing. These

Feed Materials Production Center Waste Management: Annual report for fiscal year 1986

International Nuclear Information System (INIS)

Watts, R.E.; Kottner, S.A.

1986-01-01

During FY-1986, the Westinghouse Materials Company of Ohio (WMCO) and the Department of Energy focused on safe storage and disposition of all wastes at the Feed Materials Production Center (FMPC) in compliance with federal and state regulations concerning waste management and worker health and safety. The Waste Management Annual Report identifies the comprehensive programs developed to achieve WMCO goals at the FMPC. The programs address waste issues which concern worker and public health and safety. Among those programs discussed are the decontamination, safe storage, and disposition of low-level and mixed hazardous radioactive waste. Principal attention and resources were allocated to programs which identify the largest waste streams (both currently generated and inventory backlogged). The most voluminous waste streams include low-level waste approved for shipment to the Nevada Test Site (MgF 2 slag, slag leach filter cake, and neutralized raffinate); remedial action wastes (K-65, stormwater runoff/effluent, and waste pits); thorium; and contaminated construction rubble and soil. Goals were established and met for the Waste Management Section in the form of completed milestones. The completed milestones involved such activities as characterization studies for the waste pits, K-65 Silos and adjacent areas; issuance of the Waste Management Plan required by DOE; analysis of decontamination alternatives for copper scrap; and analysis of silo structural integrity and remedial action alternatives

Calcination of Fluorinel-sodium waste blends using sugar as a feed additive (formerly WINCO-11879)

International Nuclear Information System (INIS)

Newby, B.J.; Thomson, T.D.; O'Brien, B.H.

1992-06-01

Methods were studied for using sugar as a feed additive for converting the sodium-bearing wastes stored at the Idaho Chemical Processing Plant into granular, free flowing solids by fluidized-bed calcination at 500 degrees C. All methods studied blended sodium-bearing wastes with Fluorinel wastes but differed in the types of sugar (sucrose or dextrose) that were added to the blend. The most promising sugar additive was determined to be sucrose, since it is converted more completely to inorganic carbon than is dextrose. The effect of the feed aluminum-to-alkali metal mole ratio on calcination of these blends with sugar was also investigated. Increasing the aluminum-to-alkali metal ratio from 0.6 to 1.0 decreased the calcine product-to-fines ratio from 3.0 to 1.0 and the attrition index from 80 to 15%. Further increasing the ratio to 1.25 had no effect

Tank Farm Contractor Waste Remediation System and Utilization Plan

International Nuclear Information System (INIS)

KIRKBRIDE, R.A.

1999-01-01

The Tank Waste Remediation System Operation and Utilization Plan updates the operating scenario and plans for the delivery of feed to BNFL Inc., retrieval of waste from single-shell tanks, and the overall process flowsheets for Phases I and II of the privatization of the Tank Waste Remediation System. The plans and flowsheets are updated with the most recent tank-by-tank inventory and sludge washing data. Sensitivity cases were run to evaluate the impact or benefits of proposed changes to the BNFL Inc. contract and to evaluate a risk-based SST retrieval strategy

Delivery of dsRNA through topical feeding for RNA interference in the citrus sap piercing-sucking hemipteran, Diaphorina citri.

Science.gov (United States)

Killiny, Nabil; Kishk, Abdelaziz

2017-06-01

RNA interference (RNAi) is a powerful means to study functional genomics in insects. The delivery of dsRNA is a challenging step in the development of RNAi assay. Here, we describe a new delivery method to increase the effectiveness of RNAi in the Asian citrus psyllid Diaphorina citri. Bromophenol blue droplets were topically applied to fifth instar nymphs and adults on the ventral side of the thorax between the three pairs of legs. In addition to video recordings that showed sucking of the bromophenol blue by the stylets, dissected guts turned blue indicating that the uptake was through feeding. Thus, we called the method topical feeding. We targeted the abnormal wing disc gene (awd), also called nucleoside diphosphate kinase (NDPK), as a reporter gene to prove the uptake of dsRNA via this method of delivery. Our results showed that dsRNA-awd caused reduction of awd expression and nymph mortality. Survival and lifespan of adults emerged from treated nymphs and treated adults were affected. Silencing awd caused wing malformation in the adults emerged from treated nymphs. Topical feeding as a delivery of dsRNA is highly efficient for both nymphs and adults. The described method could be used to increase the efficiency of RNAi in D. citri and other sap piercing-sucking hemipterans. © 2017 Wiley Periodicals, Inc.

Control of DWPF [Defense Waste Processing Facility] melter feed composition

International Nuclear Information System (INIS)

Edwards, R.E. Jr.; Brown, K.G.; Postles, R.L.

1990-01-01

The Defense Waste Processing Facility will be used to immobilize Savannah River Site high-level waste into a stable borosilicate glass for disposal in a geologic repository. Proper control of the melter feed composition in this facility is essential to the production of glass which meets product durability constraints dictated by repository regulations and facility processing constraints dictated by melter design. A technique has been developed which utilizes glass property models to determine acceptable processing regions based on the multiple constraints imposed on the glass product and to display these regions graphically. This system along with the batch simulation of the process is being used to form the basis for the statistical process control system for the facility. 13 refs., 3 figs., 1 tab

Round-bale feeder design affects hay waste and economics during horse feeding.

Science.gov (United States)

Martinson, K; Wilson, J; Cleary, K; Lazarus, W; Thomas, W; Hathaway, M

2012-03-01

Many horse owners find round bales convenient, less labor intensive, and more affordable than other hay types, but report an inability to control horse BW gain and excessive hay waste. The objectives were to compare hay waste, hay intake, and payback of 9 round-bale feeders and a no-feeder control when used during horse feeding. Nine round-bale feeders were tested: Cinch Net, Cone, Covered Cradle, Hayhut, Hay Sleigh, Ring, Tombstone, Tombstone Saver, and Waste Less. Each feeder design was placed on the ground in a dirt paddock. Five groups of 5 horses were fed in rotation for a 4-d period with each feeder. Every fourth day, groups were rotated among paddocks and a new round bale was placed in each feeder. In the 5 paddocks used, 5 feeders were installed for d 1 through 20, and the remaining 4 feeders and no-feeder control were installed for d 21 through 40. Groups of horses were sequentially assigned to feeders using two 5 × 5 Latin squares, the first for d 1 through 20, the second for d 21 through 40. Horse groups of similar age, BW, breed, and sex were formed from 25 Quarter Horse and Thoroughbred geldings and open mares (means: 11 yr; 541 kg of BW). Hay on the ground surrounding the feeder was collected daily, dried, and weighed. The total amount of hay removed around each feeder for a 4-d period was considered waste. Dry matter intake was estimated as the difference between hay disappearance and waste. Number of months for the reduction in waste to repay feeder cost (payback) were calculated using hay valued at $110/t, and improved feeder efficiency over the control. Feeder design did not affect hay intake (P > 0.05); all feeders resulted in an estimated hay intake of 2.0 to 2.4% BW; the no-feeder control resulted in a reduced intake of 1.3% BW (P = 0.001). Mean percentage of hay waste differed among feeders (P feeder control, 57%. Feeder design also affected payback (P feeder design affected hay waste and payback, but not estimated hay intake or BW change

Feed Materials Production Center waste management plan (Revision to NLCO-1100, R.6)

International Nuclear Information System (INIS)

Watts, R.E.; Allen, T.; Castle, S.A.; Hopper, J.P.; Oelrich, R.L.

1986-01-01

In the process of producing uranium metal products used in Department of Energy (DOE) defense programs at other DOE facilities, various types of wastes are generated at the Feed Materials Production Center (FMPC). Process wastes, both generated and stored, are discussed in the Waste Management Plan and include low-level radioactive waste (LLW), mixed hazardous/radioactive waste, and sanitary/industrial waste. Scrap metal waste and wastes requiring special remediation are also addressed in the Plan. The Waste Management Plan identifies the comprehensive programs developed to address safe storage and disposition of all wastes from past, present, and future operations at the FMPC. Waste streams discussed in this Plan are representative of the wastes generated and waste types that concern worker and public health and safety. Budgets and schedules for implementation of waste disposition are also addressed. The waste streams receiving the largest amount of funding include LLW approved for shipment by DOE/ORO to the Nevada Test Site (NTS) (MgF 2 , slag leach filter cake, and neutralized raffinate); remedial action wastes (waste pits, K-65 silo waste); thorium; scrap metal (contaminated and noncontaminated ferrous and copper scrap); construction rubble and soil generated from decontamination and decommissioning of outdated facilities; and low-level wastes that will be handled through the Low-Level Waste Processing and Shipping System (LLWPSS). Waste Management milestones are also provided. The Waste Management Plan is divided into eight major sections: Introduction; Site Waste and Waste Generating Process; Strategy; Projects and Operations; Waste Stream Budgets; Milestones; Quality Assurance for Waste Management; and Environmental Monitoring Program

Appropriate Usage Level of Shrimp Waste Meal as Chitin Source for Feeding Young Crayfish (Astacus leptodactylus Esch. 1823

Directory of Open Access Journals (Sweden)

Seval Bahadır Koca*, Nalan Ozgur Yigit, Arife Dulluc, Gonca Erol1, Nihal Cılbız1 and Ramazan Kucukkara1

2011-06-01

Full Text Available This study was conducted to determine effects of shrimp waste meal as natural chitin source at different rates (0 (control, 10, 20, 30 and 40% on growth, feed conversion ratio (FCR, survival of young crayfish (1.61±0.04 g and 3.74±0.03 cm for 60 days. Fifteen glass aquariums (70x30x40 cm were used in the experiment and 20 individuals were stocked per aquarium (95/m2. The highest of final weight and weight gain were obtained in feed with 10% shrimp waste meal group (3.29±0.23 and 1.66±0.23 g, while the lowest of final weight and weight gain was obtained in fed with 40% shrimp waste meal group (2.75±0.35 and 1.18±0.37 g, respectively. However, non-significant differences were found between final weight, weight gain, specific growth rate, final total length, feed conversion ratio, survival percentage among groups at the end of experimental period. It was concluded that shrimp waste meal as natural chitin source can be used in young crayfish diets up to 40% without adverse effect influence on growth.

Waste feed from coastal fish farms: A trophic subsidy with compositional side-effects for wild gadoids

Science.gov (United States)

Fernandez-Jover, Damian; Martinez-Rubio, Laura; Sanchez-Jerez, Pablo; Bayle-Sempere, Just T.; Lopez Jimenez, Jose Angel; Martínez Lopez, Francisco Javier; Bjørn, Pål-Arne; Uglem, Ingebrigt; Dempster, Tim

2011-03-01

Aquaculture of carnivorous fish species in sea-cages typically uses artificial feeds, with a proportion of these feeds lost to the surrounding environment. This lost resource may provide a trophic subsidy to wild fish in the vicinity of fish farms, yet the physiological consequences of the consumption of waste feed by wild fish remain unclear. In two regions in Norway with intensive aquaculture, we tested whether wild saithe ( Pollachius virens) and Atlantic cod ( Gadus morhua) associated with fish farms (F assoc), where waste feed is readily available, had modified diets, condition and fatty acid (FA) compositions in their muscle and liver tissues compared to fish unassociated (UA) with farms. Stomach content analyses revealed that both cod and saithe consumed waste feed in the vicinity of farms (6-96% of their diet was composed of food pellets). This translated into elevated body and liver condition compared to fish caught distant from farms for cod at both locations and elevated body condition for saithe at one of the locations. As a consequence of a modified diet, we detected significantly increased concentrations of terrestrial-derived fatty acids (FAs) such as linoleic (18:2ω6) and oleic (18:1ω9) acids and decreased concentrations of DHA (22:6ω3) in the muscle and/or liver of F assoc cod and saithe when compared with UA fish. In addition, the ω3:ω6 ratio clearly differed between F assoc and UA fish. Linear discriminant analysis (LDA) correctly classified 97% of fish into F assoc or UA origin for both cod and saithe based on the FA composition of liver tissues, and 89% of cod and 86% of saithe into F assoc or UA origin based on the FA composition of muscle. Thus, LDA appears a useful tool for detecting the influence of fish farms on the FA composition of wild fish. Ready availability of waste feed with high protein and fat content provides a clear trophic subsidy to wild fish in coastal waters, yet whether the accompanying side-effect of altered fatty

Development of the high-level waste high-temperature melter feed preparation flowsheet for vitrification process testing

International Nuclear Information System (INIS)

Seymour, R.G.

1995-01-01

High-level waste (HLW) feed preparation flowsheet development was initiated in fiscal year (FY) 1994 to evaluate alternative flowsheets for preparing melter feed for high-temperature melter (HTM) vitrification testing. Three flowsheets were proposed that might lead to increased processing capacity relative to the Hanford Waste Vitrification Plant (HWVP) and that were flexible enough to use with other HLW melter technologies. This document describes the decision path that led to the selection of flowsheets to be tested in the FY 1994 small-scale HTM tests. Feed preparation flowsheet development for the HLW HTM was based on the feed preparation flowsheet that was developed for the HWVP. This approach allowed the HLW program to build upon the extensive feed preparation flowsheet database developed under the HWVP Project. Primary adjustments to the HWVP flowsheet were to the acid adjustment and glass component additions. Developmental background regarding the individual features of the HLW feed preparation flowsheets is provided. Applicability of the HWVP flowsheet features to the new HLW vitrification mission is discussed. The proposed flowsheets were tested at the laboratory-scale at Pacific Northwest Laboratory. Based on the results of this testing and previously established criteria, a reductant-based flowsheet using glycolic acid and a nitric acid-based flowsheet were selected for the FY 1994 small-scale HTM testing

Evaluation of high-level waste vitrification feed preparation chemistry for an NCAW simulant, FY 1994: Alternate flowsheets (DRAFT)

International Nuclear Information System (INIS)

Smith, H.D.; Merz, M.D.; Wiemers, K.D.; Smith, G.L.

1996-02-01

High-level radioactive waste stored in tanks at the U.S. Department of Energy's (DOE's) Hanford Site will be pretreated to concentrate radioactive constituents and fed to the vitrification plant A flowsheet for feed preparation within the vitrification plant (based on the Hanford Waste Vitrification Plant (HWVP) design) called for HCOOH addition during the feed preparation step to adjust rheology and glass redox conditions. However, the potential for generating H 2 and NH 3 during treatment of high-level waste (HLW) with HCOOH was identified at Pacific Northwest Laboratory (PNL). Studies at the University of Georgia, under contract with Savannah River Technology Center (SRTC) and PNL, have verified the catalytic role of noble metals (Pd, Rh, Ru), present in the waste, in the generation of H 2 and NH 3 . Both laboratory-scale and pilot-scale studies at SRTC have documented the H 2 and NH 3 generation phenomenal Because H 2 and NH 3 may create hazardous conditions in the vessel vapor space and offgas system of a vitrification plant, reducing the H 2 generation rate and the NH 3 generation to the lowest possible levels consistent with desired melter feed characteristics is important. The Fiscal Year 1993 and 1994 studies were conducted with simulated (non-radioactive), pre-treated neutralized current acid waste (NCAW). Neutralized current acid waste is a high-level waste originating from the plutonium/uranium extraction (PUREX) plant that has been partially denitrated with sugar, neutralized with NaOH, and is presently stored in double-shell tanks. The non-radioactive simulant used for the present study includes all of the trace components found in the waste, or substitutes a chemically similar element for radioactive or very toxic species. The composition and simulant preparation steps were chosen to best simulate the chemical processing characteristics of the actual waste

Upgrading of oil palm wastes to animal feeds by radiation and fermentation treatment

International Nuclear Information System (INIS)

Kume, Tamikazu; Ito, Hitoshi; Hashimoto, Shoji; Mutaat, H.H.; Awang, M.R.

1992-01-01

Upgrading of oil palm cellulosic wastes to animal feeds by radiation and fermentation treatment has been investigated in order to recycle the agro-resources and to reduce the smoke pollution. The process is as follows; decontamination of microorganisms in fermentation media using oil palm wastes by irradiation, inoculation of useful microorganisms, and subsequent microbial digestion of cellulosic materials as well as production of proteins. The dose of 25 kGy was required to sterilize the contaminated bacteria whereas the dose of 5 - 10 kGy was enough to eliminate the fungi. Among many kinds of fungi tested, C. cinereus was selected as the most suitable seed microorganism for the fermentation of EFB (Empty Fruit Bunch of oil palm). The protein content increased to 13 % and the crude fiber content decreased to 20 % after 30 days incubation with C. cinereus at 30degC in solid state fermentation. It is considered that these fermented products can be used for the ruminant animal feeds. (author)

Effects of feeding untreated, pasteurized and acidified waste milk and bunk tank milk on the performance, serum metabolic profiles, immunity, and intestinal development in Holstein calves.

Science.gov (United States)

Zou, Yang; Wang, Yajing; Deng, Youfei; Cao, Zhijun; Li, Shengli; Wang, Jiufeng

2017-01-01

The present experiment was performed to assess the effects of different sources of milk on the growth performance, serum metabolism, immunity, and intestinal development of calves. Eighty-four Holstein male neonatal calves were assigned to one of the following four treatment groups: those that received bunk tank milk (BTM), untreated waste milk (UWM), pasteurized waste milk (PWM), and acidified waste milk (AWM) for 21 d. Calves in the BTM and AWM groups consumed more starter ( P  feeding on BTM had lower ( P  waste milk. The efficiency of feeding pasteurized and acidified waste milk are comparable, and the acidification of waste milk is an acceptable labor-saving and diarrhea-preventing feed for young calves.

Demonstrating Reliable High Level Waste Slurry Sampling Techniques to Support Hanford Waste Processing

Energy Technology Data Exchange (ETDEWEB)

Kelly, Steven E.

2013-11-11

The Hanford Tank Operations Contractor (TOC) and the Hanford Waste Treatment and Immobilization Plant (WTP) contractor are both engaged in demonstrating mixing, sampling, and transfer system capability using simulated Hanford High-Level Waste (HL W) formulations. This work represents one of the remaining technical issues with the high-level waste treatment mission at Hanford. The TOC must demonstrate the ability to adequately mix and sample high-level waste feed to meet the WTP Waste Acceptance Criteria and Data Quality Objectives. The sampling method employed must support both TOC and WTP requirements. To facilitate information transfer between the two facilities the mixing and sampling demonstrations are led by the One System Integrated Project Team. The One System team, Waste Feed Delivery Mixing and Sampling Program, has developed a full scale sampling loop to demonstrate sampler capability. This paper discusses the full scale sampling loops ability to meet precision and accuracy requirements, including lessons learned during testing. Results of the testing showed that the Isolok(R) sampler chosen for implementation provides precise, repeatable results. The Isolok(R) sampler accuracy as tested did not meet test success criteria. Review of test data and the test platform following testing by a sampling expert identified several issues regarding the sampler used to provide reference material used to judge the Isolok's accuracy. Recommendations were made to obtain new data to evaluate the sampler's accuracy utilizing a reference sampler that follows good sampling protocol.

Demonstrating Reliable High Level Waste Slurry Sampling Techniques to Support Hanford Waste Processing

International Nuclear Information System (INIS)

Kelly, Steven E.

2013-01-01

The Hanford Tank Operations Contractor (TOC) and the Hanford Waste Treatment and Immobilization Plant (WTP) contractor are both engaged in demonstrating mixing, sampling, and transfer system capability using simulated Hanford High-Level Waste (HL W) formulations. This work represents one of the remaining technical issues with the high-level waste treatment mission at Hanford. The TOC must demonstrate the ability to adequately mix and sample high-level waste feed to meet the WTP Waste Acceptance Criteria and Data Quality Objectives. The sampling method employed must support both TOC and WTP requirements. To facilitate information transfer between the two facilities the mixing and sampling demonstrations are led by the One System Integrated Project Team. The One System team, Waste Feed Delivery Mixing and Sampling Program, has developed a full scale sampling loop to demonstrate sampler capability. This paper discusses the full scale sampling loops ability to meet precision and accuracy requirements, including lessons learned during testing. Results of the testing showed that the Isolok(R) sampler chosen for implementation provides precise, repeatable results. The Isolok(R) sampler accuracy as tested did not meet test success criteria. Review of test data and the test platform following testing by a sampling expert identified several issues regarding the sampler used to provide reference material used to judge the Isolok's accuracy. Recommendations were made to obtain new data to evaluate the sampler's accuracy utilizing a reference sampler that follows good sampling protocol

Hanford Tank Waste - Near Source Treatment of Low Activity Waste

International Nuclear Information System (INIS)

Ramsey, William Gene

2013-01-01

Abstract only. Treatment and disposition of Hanford Site waste as currently planned consists of 100+ waste retrievals, waste delivery through up to 8+ miles of dedicated, in-ground piping, centralized mixing and blending operations- all leading to pre-treatment combination and separation processes followed by vitrification at the Hanford Tank Waste Treatment and Immobilization Plant (WTP). The sequential nature of Tank Farm and WTP operations requires nominally 15-20 years of continuous operations before all waste can be retrieved from many Single Shell Tanks (SSTs). Also, the infrastructure necessary to mobilize and deliver the waste requires significant investment beyond that required for the WTP. Treating waste as closely as possible to individual tanks or groups- as allowed by the waste characteristics- is being investigated to determine the potential to 1) defer, reduce, and/or eliminate infrastructure requirements, and 2) significantly mitigate project risk by reducing the potential and impact of single point failures. The inventory of Hanford waste slated for processing and disposition as LAW is currently managed as high-level waste (HLW), i.e., the separation of fission products and other radionuclides has not commenced. A significant inventory of this waste (over 20M gallons) is in the form of precipitated saltcake maintained in single shell tanks, many of which are identified as potential leaking tanks. Retrieval and transport (as a liquid) must be staged within the waste feed delivery capability established by site infrastructure and WTP. Near Source treatment, if employed, would provide for the separation and stabilization processing necessary for waste located in remote farms (wherein most of the leaking tanks reside) significantly earlier than currently projected. Near Source treatment is intended to address the currently accepted site risk and also provides means to mitigate future issues likely to be faced over the coming decades. This paper

Evaluation of alternative chemical additives for high-level waste vitrification feed preparation processing

International Nuclear Information System (INIS)

Seymour, R.G.

1995-01-01

During the development of the feed processing flowsheet for the Defense Waste Processing Facility (DWPF) at the Savannah River Site (SRS), research had shown that use of formic acid (HCOOH) could accomplish several processing objectives with one chemical addition. These objectives included the decomposition of tetraphenylborate, chemical reduction of mercury, production of acceptable rheological properties in the feed slurry, and controlling the oxidation state of the glass melt pool. However, the DEPF research had not shown that some vitrification slurry feeds had a tendency to evolve hydrogen (H 2 ) and ammonia (NH 3 ) as the result of catalytic decomposition of CHOOH with noble metals (rhodium, ruthenium, palladium) in the feed. Testing conducted at Pacific Northwest Laboratory and later at the Savannah River Technical Center showed that the H 2 and NH 3 could evolve at appreciable rates and quantities. The explosive nature of H 2 and NH 3 (as ammonium nitrate) warranted significant mitigation control and redesign of both facilities. At the time the explosive gas evolution was discovered, the DWPF was already under construction and an immediate hardware fix in tandem with flowsheet changes was necessary. However, the Hanford Waste Vitrification Plant (HWVP) was in the design phase and could afford to take time to investigate flowsheet manipulations that could solve the problem, rather than a hardware fix. Thus, the HWVP began to investigate alternatives to using HCOOH in the vitrification process. This document describes the selection, evaluation criteria, and strategy used to evaluate the performance of the alternative chemical additives to CHOOH. The status of the evaluation is also discussed

Conversion of nuclear waste to molten glass: Formation of porous amorphous alumina in a high-Al melter feed

Energy Technology Data Exchange (ETDEWEB)

Xu, Kai, E-mail: kaixu@whut.edu.cn [Pacific Northwest National Laboratory, Richland, WA 99352 (United States); Hrma, Pavel, E-mail: pavel.hrma@pnnl.gov [Pacific Northwest National Laboratory, Richland, WA 99352 (United States); Washton, Nancy; Schweiger, Michael J. [Pacific Northwest National Laboratory, Richland, WA 99352 (United States); Kruger, Albert A. [U.S. Department of Energy, Office of River Protection, Richland, WA 99352 (United States)

2017-01-15

The transition of Al phases in a simulated high-Al high-level nuclear waste melter feed heated at 5 K min{sup −1} to 700 °C was investigated with transmission electron microscopy, {sup 27}Al nuclear magnetic resonance spectroscopy, the Brunauer-Emmett-Teller method, and X-ray diffraction. At temperatures between 300 and 500 °C, porous amorphous alumina formed from the dehydration of gibbsite, resulting in increased specific surface area of the feed (∼8 m{sup 2} g{sup −1}). The high-surface-area amorphous alumina formed in this manner could potentially stop salt migration in the cold cap during nuclear waste vitrification. - Highlights: • Porous amorphous alumina formed in a simulated high-Al HLW melter feed during heating. • The feed had a high specific surface area at 300 °C ≤ T ≤ 500 °C. • Porous amorphous alumina induced increased specific surface area.

Aquaponics: integrating fish feeding rates and ion waste production for strawberry hydroponics

International Nuclear Information System (INIS)

Villarroel, M.; Alvarino, J. M. R.; Duran, J. M.

2011-01-01

Aquaponics is the science of integrating intensive fish aquaculture with plant production in recirculating water systems. Although ion waste production by f ish cannot satisfy all plant requirements, less is known about the relationship between total feed provided for f ish and the production of milliequivalents (mEq) of different macronutrients for plants, especially for nutrient flow hydroponics used for strawberry production in Spain. That knowledge is essential to consider the amount of macronutrients available in aquaculture systems so that farmers can estimate how much nutrient needs to be supplemented in the waste water from fish, to produce viable plant growth. In the present experiment, tilapia (Oreochromis niloticus L.) were grown in a small-scale recirculating system at two different densities while growth and feed consumption were noted every week for five weeks. At the same time points, water samples were taken to measure pH, EC 2 5, HCO3 - , Cl - , NH + 4 , NO 2 - , NO 3 - , H 2 PO 4 - , SO 4 2 -, Na + , K + , Ca 2 + and Mg 2 + build up. The total increase in mEq of each ion per kg of feed provided to the fish was highest for NO 3 - , followed, in decreasing order, by Ca 2 +, H 2 PO 4 - , K + , Mg 2 + and SO 4 2 -. The total amount of feed required per mEq ranged from 1.61- 13.1 kg for the four most abundant ions (NO 3 - , Ca 2 +, H 2 PO 4 - and K + ) at a density of 2 kg fish m3, suggesting that it would be rather easy to maintain small populations of fish to reduce the cost of hydroponic solution supplementation for strawberries. (Author) 16 refs.

Use of food waste, fish waste and food processing waste for China's aquaculture industry: Needs and challenge.

Science.gov (United States)

Mo, Wing Yin; Man, Yu Bon; Wong, Ming Hung

2018-02-01

China's aquaculture industry is growing dramatically in recent years and now accounts for 60.5% of global aquaculture production. Fish protein is expected to play an important role in China's food security. Formulated feed has become the main diet of farmed fish. The species farmed have been diversified, and a large amount of 'trash fish' is directly used as feed or is processed into fishmeal for fish feed. The use of locally available food waste as an alternative protein source for producing fish feed has been suggested as a means of tackling the problem of sourcing safe and sustainable feed. This paper reviews the feasibility of using locally available waste materials, including fish waste, okara and food waste. Although the fishmeal derived from fish waste, okara or food waste is less nutritious than fishmeal from whole fish or soybean meal, most fish species farmed in China, such as tilapia and various Chinese carp, grow well on diets with minimal amounts of fishmeal and 40% digestible carbohydrate. It can be concluded that food waste is suitable as a component of the diet of farmed fish. However, it will be necessary to revise regulations on feed and feed ingredients to facilitate the use of food waste in the manufacture of fish feed. Copyright © 2017 Elsevier B.V. All rights reserved.

Conversion of nuclear waste to molten glass: Formation of porous amorphous alumina in a high-Al melter feed

Science.gov (United States)

Xu, Kai; Hrma, Pavel; Washton, Nancy; Schweiger, Michael J.; Kruger, Albert A.

2017-01-01

The transition of Al phases in a simulated high-Al high-level nuclear waste melter feed heated at 5 K min-1 to 700 °C was investigated with transmission electron microscopy, 27Al nuclear magnetic resonance spectroscopy, the Brunauer-Emmett-Teller method, and X-ray diffraction. At temperatures between 300 and 500 °C, porous amorphous alumina formed from the dehydration of gibbsite, resulting in increased specific surface area of the feed (∼8 m2 g-1). The high-surface-area amorphous alumina formed in this manner could potentially stop salt migration in the cold cap during nuclear waste vitrification.

In-flight food delivery and waste collection service: the passengers’ perspective and potential improvement

Science.gov (United States)

Romli, F. I.; Rahman, K. Abdul; Ishak, F. D.

2016-10-01

Increased competition in the commercial air transportation industry has made service quality of the airlines as one of the key competitive measures to attract passengers against their rivals. In-flight services, particularly food delivery and waste collection, have a notable impact on perception of the overall airline's service quality because they are directly and interactively provided to passengers during flight. An online public survey is conducted to explore general passengers' perception of current in-flight food delivery and waste collection services, and to identify potential rooms for improvement. The obtained survey results indicate that in-flight service does have an effect on passengers' choice of airlines. Several weaknesses of the current service method and possible improvements have been established from the collected responses.

Slurry feed variability in West Valley's melter feed tank and sampling system

International Nuclear Information System (INIS)

Fow, C.L.; Kurath, D.E.; Pulsipher, B.A.; Bauer, B.P.

1989-04-01

The present plan for disposal of high-level wastes at West Valley is to vitrify the wastes for disposal in deep geologic repository. The vitrification process involves mixing the high-level wastes with glass-forming chemicals and feeding the resulting slurry to a liquid-fed ceramic melter. Maintaining the quality of the glass product and proficient melter operation depends on the ability of the melter feed system to produce and maintain a homogeneous mixture of waste and glass-former materials. To investigate the mixing properties of the melter feed preparation system at West Valley, a statistically designed experiment was conducted using synthetic melter feed slurry over a range of concentrations. On the basis of the statistical data analysis, it was found that (1) a homogeneous slurry is produced in the melter feed tank, (2) the liquid-sampling system provides slurry samples that are statistically different from the slurry in the tank, and (3) analytical measurements are the major source of variability. A statistical quality control program for the analytical laboratory and a characterization test of the actual sampling system is recommended. 1 ref., 5 figs., 1 tab

A novel shredder for municipal solid waste (MSW): influence of feed moisture on breakage performance.

Science.gov (United States)

Luo, Siyi; Xiao, Bo; Xiao, Lei

2010-08-01

A novel MSW shredder was presented but many aspects of the shredder have not been fully characterized. The feed moisture is an important factor that influences crushing performance. This paper focuses on the effect of feed moisture. The breakage of municipal solid waste (MSW) at several moisture levels (0%, 10%, 20%, 40% and 60%) was conducted with a laboratory shredder to investigate the effect of feed moisture on product size distribution and specific energy consumption under two different hydraulic pressures (40 and 60 kg/cm(2)). The results showed definite effects of feed moisture on the product size distribution and specific energy consumption: there is a tendency for the fine production in products to decrease with increasing amounts of water content in the feed; with the increasing feed moisture, specific energy shows an increasing trend; the specific energy and product size distribution under lower hydraulic pressure is more sensitive to the feed moisture than it is under higher hydraulic pressure. (c) 2010. Published by Elsevier Ltd. All rights reserved.

Performance of crossbred heifers in different step-down waste milk-feeding strategies.

Science.gov (United States)

Leão, Juliana Mergh; Lima, Juliana Aparecida Mello; Lana, Ângela Maria Quintão; Saturnino, Helton Mattana; Reis, Ronaldo Braga; Barbosa, Fabiano Alvim; de Azevedo, Rafael Alves; Sá Fortes, Robson Vilela; Coelho, Sandra Gesteira

2016-12-01

The aim of this study was to evaluate the consumption, performance, feed efficiency, glucose concentration, and the cost per kilogram of weight gain of crossbred Holstein-Gyr heifers (n = 33) subjected to one of the three waste milk step-down strategies: 6L-30d/4L-60d/2L-90d (T1), 6L-45d/4L-60d/2L-90d (T2), and 8L-30d/6L-60d/3L-90d (T3). Heifers were weaned at the age of 91 days. Water and starter were provided ad libitum. The average waste milk intake was higher in T3 than in T1 and T2 strategies until 30 days and between 60 and 90 days. The starter intake did not differ among the strategies until 45 days, but it was higher in strategy T1 than in strategy T3 between 60 and 90 days. The waste milk step-down strategy did not influence the total dry matter intake, average daily gain, body weight, and feed efficiency. Glucose concentrations in plasma varied within a range that could be considered normal and were similar among the treatments. The average cost per kilogram of weight gain was the lowest in strategy T1 (US$3.0) compared to that in the other strategies (T2, US$3.2, and T3, US$3.6). The 6L-30d/4L-60d/2L-90d waste milk step-down strategy was the most effective, since it increased the starter intake, led to normal glucose concentrations in plasma, and caused similar weight gain compared with the other strategies; however, it had a lower cost per kilogram.

Effects of Quartz Particle Size and Sucrose Addition on Melting Behavior of a Melter Feed for High-Level Waste Glass

International Nuclear Information System (INIS)

Marcial, Jose; Hrma, Pavel R.; Schweiger, Michael J.; Swearingen, Kevin J.; Tegrotenhuis, Nathan E.; Henager, Samuel H.

2010-01-01

The behavior of melter feed (a mixture of nuclear waste and glass-forming additives) during waste-glass processing has a significant impact on the rate of the vitrification process. We studied the effects of silica particle size and sucrose addition on the volumetric expansion (foaming) of a high-alumina feed and the rate of dissolution of silica particles in feed samples heated at 5 C/min up to 1200 C. The initial size of quartz particles in feed ranged from 5 to 195 (micro)m. The fraction of the sucrose added ranged from 0 to 0.20 g per g glass. Extensive foaming occurred only in feeds with 5-(micro)m quartz particles; particles (ge) 150 (micro)m formed clusters. Particles of 5 (micro)m completely dissolved by 900 C whereas particles (ge) 150 (micro)m did not fully dissolve even when the temperature reached 1200 C. Sucrose addition had virtually zero impact on both foaming and the dissolution of silica particles.

METHODS FOR DETERMINING AGITATOR MIXING REQUIREMENTS FOR A MIXING & SAMPLING FACILITY TO FEED WTP (WASTE TREATMENT PLANT)

Energy Technology Data Exchange (ETDEWEB)

GRIFFIN PW

2009-08-27

The following report is a summary of work conducted to evaluate the ability of existing correlative techniques and alternative methods to accurately estimate impeller speed and power requirements for mechanical mixers proposed for use in a mixing and sampling facility (MSF). The proposed facility would accept high level waste sludges from Hanford double-shell tanks and feed uniformly mixed high level waste to the Waste Treatment Plant. Numerous methods are evaluated and discussed, and resulting recommendations provided.

Protein from preprocessed waste activated sludge as a nutritional supplement in chicken feed.

Science.gov (United States)

Chirwa, Evans M N; Lebitso, Moses T

2014-01-01

Five groups of broiler chickens were raised on feed containing varying substitutions of single cell protein from preprocessed waste activated sludge (pWAS) in varying compositions of 0:100, 25:75, 50:50, 75:25, and 100:0 pWAS: fishmeal by mass. Forty chickens per batch were evaluated for growth rate, mortality rate, and feed conversion efficiency (ηє). The initial mass gain rate, mortality rate, initial and operational cost analyses showed that protein from pWAS could successfully replace the commercial feed supplements with a significant cost saving without adversely affecting the health of the birds. The chickens raised on preprocessed WAS weighed 19% more than those raised on fishmeal protein supplement over a 45 day test period. Growing chickens on pWAS translated into a 46% cost saving due to the fast growth rate and minimal death losses before maturity.

Food wastes as fish feeds for polyculture of low-trophic-level fish: bioaccumulation and health risk assessments of heavy metals in the cultured fish.

Science.gov (United States)

Cheng, Zhang; Lam, Cheung-Lung; Mo, Wing-Yin; Nie, Xiang-Ping; Choi, Wai-Ming; Man, Yu-Bon; Wong, Ming-Hung

2016-04-01

The major purpose of this study was to use different types of food wastes which serve as the major sources of protein to replace the fish meal used in fish feeds to produce quality fish. Two types of food waste-based feed pellets FW A (with cereals) and FW B (with cereals and meat products) and the commercial feed Jinfeng® were used to culture fingerlings of three low-trophic-level fish species: bighead carp, grass carp, and mud carp (in the ratio of 1:3:1) for 1 year period in the Sha Tau Kok Organic Farm in Hong Kong. Heavy metal concentrations in all of the fish species fed with food waste pellets and commercial pellets in Sha Tau Kok fish ponds were all below the local and international maximum permissible levels in food. Health risk assessments indicated that human consumption of the fish fed with food waste feed pellets was safe for the Hong Kong residents. The present results revealed that recycling of food waste for cultivating low-trophic-level fish (mainly herbivores and detritus feeders) is feasible, and at the same time will ease the disposal pressure of food waste, a common problem of densely populated cities like Hong Kong.

Effect of feed presentation on feeding patterns of dairy calves.

Science.gov (United States)

Miller-Cushon, E K; Bergeron, R; Leslie, K E; Mason, G J; DeVries, T J

2013-01-01

The objectives of this study were to determine the effect of feed presentation on meal frequency and duration, as well as diurnal feeding patterns of dairy calves, and to assess any longer-term differences in feeding patterns resulting from previous experience. Twenty Holstein bull calves were exposed from wk 1 to 8 of life to 1 of 2 feed presentation treatments: concentrate and chopped grass hay (Feed was provided ad libitum. Calves received 8L/d of milk replacer (1.2 kg of dry matter), with the amount progressively reduced after 5 wk to facilitate weaning by the end of wk 7. At the beginning of wk 9, all calves received the MIX diet and remained on trial for an additional 3 wk. Feeding behavior was recorded from video for 4d during wk 6, 8, 9, and 11. In wk 6, calves fed MIX spent more time feeding than calves fed COM (56.7 vs. 46.8 min/d). In wk 8, calves fed MIX spent more time feeding (174.0 vs. 139.1 min/d) and had a lower rate of intake (11.5 vs. 14.7 g/min) compared with calves fed COM. Meal frequency was similar between treatments (12.2 meals/d). Diurnal feeding patterns in wk 8 were also affected by feed presentation, with calves fed MIX spending less time feeding at time of feed delivery and more time feeding throughout the rest of the daylight hours than calves fed COM. Diurnal feeding patterns of hay and concentrate in wk 8 differed for calves fed COM, with more time spent consuming hay at time of feed delivery and less time spent consuming hay throughout the rest of the day. Once calves previously fed COM were transitioned to the MIX diet in wk 9, meal frequency, meal duration, and diurnal feeding patterns were similar between treatments: both treatments spent similar amounts of time feeding (173.9 min/d) and had similar peaks in feeding activity at time of feed delivery, sunrise, and sunset. Provision of hay and concentrate to young calves as a mixed ration, compared with separate components, increases time spent feeding and results in more evenly

A feeding protocol for delivery of agents to assess development in Varroa mites.

Directory of Open Access Journals (Sweden)

Ana R Cabrera

Full Text Available A novel feeding protocol for delivery of bio-active agents to Varroa mites was developed by providing mites with honey bee larva hemolymph supplemented with cultured insect cells and selected materials delivered on a fibrous cotton substrate. Mites were starved, fed on treated hemolymph to deliver selected agents and then returned to bee larvae. Transcript levels of two reference genes, actin and glyceraldehyde 3-phosphate dehydrogenase (GAPDH, as well as for nine selected genes involved in reproductive processes showed that the starvation and feeding protocol periods did not pose a high level of stress to the mites as transcript levels remained comparable between phoretic mites and those completing the protocol. The feeding protocol was used to deliver molecules such as hormone analogs or plasmids. Mites fed with Tebufenozide, an ecdysone analog, had higher transcript levels of shade than untreated or solvent treated mites. In order to extend this feeding protocol, cultured insect cells were incorporated to a final ratio of 1 part cells and 2 parts hemolymph. Although supplementation with Bombyx mori Bm5 cells increased the amount of hemolymph consumed per mite, there was a significant decrease in the percentage of mites that fed and survived. On the other hand, Drosophila melanogaster S2 cells reduced significantly the percentage of mites that fed and survived as well as the amount of hemolymph consumed. The feeding protocol provides a dynamic platform with which to challenge the Varroa mite to establish efficacy of control agents for this devastating honey bee pest.

75 FR 81250 - Pulse Jet Mixing at the Waste Treatment and Immobilization Plant

Science.gov (United States)

2010-12-27

... Immobilization Plant (WTP) in conjunction with the Hanford tank farm waste feed delivery system will operate... imperative requires that the pulse jet mixing and transfer systems relied upon in the WTP design perform reliably and effectively for decades of WTP operations, and that technical issues with the performance of...

Effects of Bifidobacterium Breve Feeding Strategy and Delivery Modes on Experimental Allergic Rhinitis Mice.

Directory of Open Access Journals (Sweden)

Jian-jun Ren

Full Text Available Different delivery modes may affect the susceptibility to allergic diseases. It is still unknown whether early intervention with probiotics would counteract this effect.The effect of different delivery modes on immune status and nasal symptoms was investigated on established allergic rhinitis (AR mouse model. In addition, the immunoregulatory effects and mechanisms of different feeding manners with Bifidobacterium breve(B. breve were examined.Live lyophilized B. breve was orally administered to BALB/c mice born via vaginal delivery(VD or cesarean delivery (CD for 8 consecutive weeks, after which they were sensitized by ovalbumin(OVA to establish experimental AR. Nasal symptoms, serum immunoglobulins, cytokines, splenic percentages of CD4(+CD25(+Foxp3(+ regulatory T(Treg cells and nasal eosinophil infiltration were evaluated.Compared with VD mice, mice delivered via CD demonstrated more serious nasal symptoms, higher concentrations of OVA-specific immunoglobulin (Ig E, more nasal eosinophils and lower percentages of splenic CD4(+CD25(+Foxp3(+Treg cells after establishing experimental AR. These parameters were reversed by administering B. breves hortly after birth. However, the effect of B. breve did not differ between different delivery modes.CD aggravates the nasal symptoms of AR mice compared to VD. This is the first report that oral administration of B. breve shortly after birth can significantly alleviate the symptoms of AR mice born via both deliveries, probably via activation of the regulatory capacity of CD4(+CD25(+Foxp3(+Treg cells.

Effects of Bifidobacterium Breve Feeding Strategy and Delivery Modes on Experimental Allergic Rhinitis Mice.

Science.gov (United States)

Ren, Jian-jun; Yu, Zhao; Yang, Feng-Ling; Lv, Dan; Hung, Shi; Zhang, Jie; Lin, Ping; Liu, Shi-Xi; Zhang, Nan; Bachert, Claus

2015-01-01

Different delivery modes may affect the susceptibility to allergic diseases. It is still unknown whether early intervention with probiotics would counteract this effect. The effect of different delivery modes on immune status and nasal symptoms was investigated on established allergic rhinitis (AR) mouse model. In addition, the immunoregulatory effects and mechanisms of different feeding manners with Bifidobacterium breve(B. breve) were examined. Live lyophilized B. breve was orally administered to BALB/c mice born via vaginal delivery(VD) or cesarean delivery (CD) for 8 consecutive weeks, after which they were sensitized by ovalbumin(OVA) to establish experimental AR. Nasal symptoms, serum immunoglobulins, cytokines, splenic percentages of CD4(+)CD25(+)Foxp3(+) regulatory T(Treg) cells and nasal eosinophil infiltration were evaluated. Compared with VD mice, mice delivered via CD demonstrated more serious nasal symptoms, higher concentrations of OVA-specific immunoglobulin (Ig) E, more nasal eosinophils and lower percentages of splenic CD4(+)CD25(+)Foxp3(+)Treg cells after establishing experimental AR. These parameters were reversed by administering B. breves hortly after birth. However, the effect of B. breve did not differ between different delivery modes. CD aggravates the nasal symptoms of AR mice compared to VD. This is the first report that oral administration of B. breve shortly after birth can significantly alleviate the symptoms of AR mice born via both deliveries, probably via activation of the regulatory capacity of CD4(+)CD25(+)Foxp3(+)Treg cells.

SPEEDUP simulation of liquid waste batch processing. Revision 1

International Nuclear Information System (INIS)

Shannahan, K.L.; Aull, J.E.; Dimenna, R.A.

1994-01-01

The Savannah River Site (SRS) has accumulated radioactive hazardous waste for over 40 years during the time SRS made nuclear materials for the United States Department of Energy (DOE) and its predecessors. This waste is being stored as caustic slurry in a large number of 1 million gallon steel tanks, some of which were initially constructed in the early 1950's. SRS and DOE intend to clean up the Site and convert this waste into stable forms which then can be safely stored. The liquid waste will be separated into a partially decontaminated low-level and radioactive high-level waste in one feed preparation operation, In-Tank Precipitation. The low-level waste will be used to make a concrete product called saltstone in the Saltstone Facility, a part of the Defense Waste Processing Facility (DWPF). The concrete will be poured into large vaults, where it will be permanently stored. The high-level waste will be added to glass-formers and waste slurry solids from another feed preparation operation, Extended Sludge Processing. The mixture will then be converted to a stable borosilicate glass by a vitrification process that is the other major part of the DWPF. This glass will be poured into stainless steel canisters and sent to a temporary storage facility prior to delivery to a permanent underground storage site

Engineering evaluation/cost analysis: Waste Pit Area storm water runoff control, Feed Materials Production Center, Fernald, Ohio

International Nuclear Information System (INIS)

1990-08-01

This report evaluates remedial action alternatives at the Feed Materials production Center in response to the need to contain contaminated storm water runoff. The storm water is being contaminated as it falls over a radioactive/chemical waste pit which contains uranium contaminated wastes. Alternatives considered include no action, surface capping, surface capping with lateral drainage, runoff collection and treatment, and source removal

Superconducting open-gradient magnetic separation for the pretreatment of radioactive or mixed waste vitrification feeds. 1997 annual progress report

International Nuclear Information System (INIS)

Cicero-Herman, C.A.; Ritter, J.A.

1997-01-01

'Vitrification has been selected as a final waste form technology in the US for long-term storage of high-level radioactive wastes (HLW). However, a foreseeable problem during vitrification in some waste feed streams lies in the presence of elements (e.g., transition metals) in the HLW that may cause instabilities in the final glass product. The formation of spinel compounds, such as Fe 3 O 4 and FeCrO 4 , results in glass phase separation and reduces vitrifier lifetime, and durability of the final waste form. A superconducting open gradient magnetic separation (OGMS) system maybe suitable for the removal of the deleterious transition elements (e.g. Fe, Co, and Ni) and other elements (lanthanides) from vitrification feed streams due to their ferromagnetic or paramagnetic nature. The OGMS systems are designed to deflect and collect paramagnetic minerals as they interact with a magnetic field gradient. This system has the potential to reduce the volume of HLW for vitrification and ensure a stable product. In order to design efficient OGMS and High gradient magnetic separation (HGMS) processes, a fundamental understanding of the physical and chemical properties of the waste feed streams is required. Using HLW simulant and radioactive fly ash and sludge samples from the Savannah River Technology Center, Rocky Flats site, and the Hanford reservation, several techniques were used to characterize and predict the separation capability for a superconducting OGMS system.'

Enhancement of certain agro-cellulosic wastes through radiation processing for livestock feed

International Nuclear Information System (INIS)

Farag, D.M.H.; Zakaria, S.

1999-01-01

A study was undertaken with air-dried peanut hulls, sugarcane bagasse, corn stalks, concobs, banana leaves, wheat straw and broad bean straw to determine the effect of radiation treatment up to 3 MGY on their chemical composition and the effect of enzymatic hydrolysis on treated wastes. The effect of gamma irradiation on crude protein, fat and ash of these wastes was negligible. While radiation treatment reduced the content of crude fiber in all these wastes with corresponding increases in dry matter digestibility in vitro, as a function of radiation dose. When peanut hulls, sugarcane bagasse and wheat straw were exposed to gamma rays at 0, 1, 2 and 3 MGy a linear reduction in fiber components (neutral detergent fiber, acid detergent fiber, and lignin), increased in glucose yield enzymatic hydrolysis and dry matter digestibility were observed for peanut hulls, sugarcane bagasse and wheat straw. The findings confirm that irradiation of fibrous vegetable materials could convert them into a valuable feed supplement

Preventing Buoyant Displacement Gas Release Events in Hanford Double-Shell Waste Tanks

Energy Technology Data Exchange (ETDEWEB)

Meyer, Perry A.; Stewart, Charles W.

2001-01-01

This report summarizes the predictive methods used to ensure that waste transfer operations in Hanford waste tanks do not create waste configurations that lead to unsafe gas release events. The gas release behavior of the waste in existing double-shell tanks has been well characterized, and the flammable gas safety issues associated with safe storage of waste in the current configuration are being formally resolved. However, waste is also being transferred between double-shell tanks and from single-shell tanks into double-shell tanks by saltwell pumping and sluicing that create new wastes and waste configurations that have not been studied as well. Additionally, planning is underway for various waste transfer scenarios to support waste feed delivery to the proposed vitrification plant. It is critical that such waste transfers do not create waste conditions with the potential for dangerous gas release events.

Technical and logistic provisions for the delivery of radioactive wastes in the final repository Konrad

International Nuclear Information System (INIS)

Poeppinghaus, Jens

2013-01-01

The beginning of radioactive waste delivery to the final repository Konrad is planned for 2019. The main issue for the technical and logistic provisions is the development of a concept for the transport of the licensed radioactive waste containers to the site, including a turning concept for cylindrical waste forms and planning, construction and manufacture of transport equipment. Further issues include a logistic concept considering specific boundary conditions as administrative processes, priorities, special features of the delivering institutions and technical requirements of the repository.

Waste Feed Delivery Strategy for Tanks 241-AN-102 and 241-AN-107

International Nuclear Information System (INIS)

BLACKER, S.M.

2000-01-01

This engineering study establishes the detailed retrieval strategy, equipment requirements, and key parameters for preparing detailed process flowsheets; evaluates the technical and programmatic risks associated with processing, certifying, transferring, and delivering waste from Tanks 241-AN-102 and 241-AN-107 to BNFL; and provides a list of necessary follow-on actions so that program direction from ORP can be successfully implemented

Waste Feed Delivery Strategy for Tanks 241-AN-102 and 241-AN-107

Energy Technology Data Exchange (ETDEWEB)

BLACKER, S.M.

2000-04-13

This engineering study establishes the detailed retrieval strategy, equipment requirements, and key parameters for preparing detailed process flowsheets; evaluates the technical and programmatic risks associated with processing, certifying, transferring, and delivering waste from Tanks 241-AN-102 and 241-AN-107 to BNFL; and provides a list of necessary follow-on actions so that program direction from ORP can be successfully implemented.

Aquaponics: integrating fish feeding rates and ion waste production for strawberry hydroponics

Energy Technology Data Exchange (ETDEWEB)

Villarroel, M; Alvarino, J M. R.; Duran, J M

2011-07-01

Aquaponics is the science of integrating intensive fish aquaculture with plant production in recirculating water systems. Although ion waste production by fish cannot satisfy all plant requirements, less is known about the relationship between total feed provided for fish and the production of milliequivalents (mEq) of different macronutrients for plants, especially for nutrient flow hydroponics used for strawberry production in Spain. That knowledge is essential to consider the amount of macronutrients available in aquaculture systems so that farmers can estimate how much nutrient needs to be supplemented in the waste water from fish, to produce viable plant growth. In the present experiment, tilapia (Oreochromis niloticus L.) were grown in a small-scale recirculating system at two different densities while growth and feed consumption were noted every week for five weeks. At the same time points, water samples were taken to measure pH, EC25, HCO3{sup -}, Cl{sup -}, NH{sup +}{sub 4}, NO{sub 2}{sup -}, NO{sub 3}{sup -}, H{sub 2}PO{sub 4}{sup -}, SO{sub 4}{sup 2}-, Na{sup +}, K{sup +}, Ca{sup 2}+ and Mg{sup 2}+ build up. The total increase in mEq of each ion per kg of feed provided to the fish was highest for NO{sub 3}{sup -}, followed, in decreasing order, by Ca{sup 2}+, H{sub 2}PO{sub 4}{sup -}, K{sup +}, Mg{sup 2}+ and SO{sub 4}{sup 2}-. The total amount of feed required per mEq ranged from 1.61 - 13.1 kg for the four most abundant ions (NO{sub 3}{sup -}, Ca{sup 2}+, H{sub 2}PO{sub 4}{sup -} and K{sup +}) at a density of 2 kg fish m{sup -3}, suggesting that it would be rather easy to maintain small populations of fish to reduce the cost of hydroponic solution supplementation for strawberries. (Author) 16 refs.

METHODS FOR DETERMINING AGITATOR MIXING REQUIREMENTS FOR A MIXING and SAMPLING FACILITY TO FEED WTP (WASTE TREATMENT PLANT)

International Nuclear Information System (INIS)

Griffin, P.W.

2009-01-01

The following report is a summary of work conducted to evaluate the ability of existing correlative techniques and alternative methods to accurately estimate impeller speed and power requirements for mechanical mixers proposed for use in a mixing and sampling facility (MSF). The proposed facility would accept high level waste sludges from Hanford double-shell tanks and feed uniformly mixed high level waste to the Waste Treatment Plant. Numerous methods are evaluated and discussed, and resulting recommendations provided.

Preservation of hatchery waste by lactic acid fermentation. 2. Large-scale fermentation and feeding trial to evaluate feeding value.

Science.gov (United States)

Deshmukh, A C; Patterson, P H

1997-09-01

Two waste streams from a Leghorn hatchery were preserved and recycled by fermentation with a by-product carbohydrate and extrusion processing into new feed ingredients that were evaluated with broiler chickens. Cockerel chicks (CC) and a 60:40 ratio of CC:shell waste (CC:SW) were fermented in 189-L barrels for 21 d following grinding, then mixing with a liquid culture (0.2%) and carbohydrate source at 15 and 16.66%, respectively. At 2 wk, pH was 4.44 and 5.09 for the CC and CC:SW products compared with higher values of 6.54 and 6.98 for the raw ingredients at the onset. Negligible hydrogen sulfide and no ammonia gas were recorded during the fermentation period. At 21 d, the fermented CC and CC:SW were extruded, dried, and ground to meals containing CP and TMEn levels of 47.4%, 3,187 kcal/kg, and 33.1%, 2,696 kcal/kg, respectively. Broiler chickens were fed a control diet and the CC (5 and 10%) and CC:SW (2.5 and 5%) ingredient diets with corn and soybean meal for 6 wk to evaluate feeding value and carcass yield. Body weight, gain and feed conversion at 42 d for birds fed diets supplemented with CC or CC:SW at all levels were comparable to those of the control. Diets supplemented with hatchery by-product had no negative effect on carcass measurements except ready to cook carcass and wing yield, which were significantly greater for the 10% CC:SW birds than for the control. These data indicate that nutrient dense hatchery by-products can be preserved with fermentation up to 21 d and support broiler live performance and carcass yield as dietary ingredients equal to or better than a corn-soybean meal control.

Tank Waste Remediation System (TWRS) Retrieval Authorization Basis Amendment Task Plan

International Nuclear Information System (INIS)

HARRIS, J.P.

1999-01-01

This task plan is a documented agreement between Nuclear Safety and Licensing and Retrieval Engineering. The purpose of this task plan is to identify the scope of work, tasks and deliverables, responsibilities, manpower, and schedules associated with an authorization basis amendment as a result of the Waste Feed Delivery Program, Project W-211, Project W-521, and Project W-522

Feed and organic matter

DEFF Research Database (Denmark)

Dalsgaard, Anne Johanne Tang

2011-01-01

impact on the receiving water body by reducing dissolved oxygen concentrations and increasing sedimentation. Within aquaculture systems, a high organic load may affect fish health and performance directly (e.g., gill disease) as well as indirectly (proliferation of pathogenic bacteria and parasites......, reduction of dissolved oxygen concentrations, etc.). In recirculating aquaculture systems (RAS), a high organic load caused by limited water exchange may affect biofilter performance by favouring heterotrophic bacteria at the expense of autotrophic, nitrifying bacteria. Organic waste in RAS primarily...... originates from undigested feed, but also metabolic losses, mucus, dead tissue, feed waste and intake water may contribute. The nutrient composition of the feed affects the quantity and composition of the organic (undigested) waste, and including for example plant protein ingredients may affect...

Evaluation of tank waste transfers at 241-AW tank farm

International Nuclear Information System (INIS)

Willis, W.L.

1998-01-01

A number of waste transfers are needed to process and feed waste to the private contractors in support of Phase 1 Privatization. Other waste transfers are needed to support the 242-A Evaporator, saltwell pumping, and other ongoing Tank Waste Remediation System (TWRS) operations. The purpose of this evaluation is to determine if existing or planned equipment and systems are capable of supporting the Privatization Mission of the Tank Farms and continuing operations through the end of Phase 1B Privatization Mission. Projects W-211 and W-314 have been established and will support the privatization effort. Equipment and system upgrades provided by these projects (W-211 and W-314) will also support other ongoing operations in the tank farms. It is recognized that these projects do not support the entire transfer schedule represented in the Tank Waste Remediation system Operation and Utilization Plan. Additionally, transfers surrounding the 241-AW farm must be considered. This evaluation is provided as information, which will help to define transfer paths required to complete the Waste Feed Delivery (WFD) mission. This document is not focused on changing a particular project, but it is realized that new project work in the 241-AW Tank Farm is required

The technology of fish-vegetable feed production

Directory of Open Access Journals (Sweden)

Mukatova M. D.

2016-09-01

Full Text Available Perspective direction of the Volga-Caspian basin fisheries is increasing the productivity of aquaculture production which requires the availability of sufficient quantities of feed. The cutting waste of carp and crucian carp, crayfish processing (cephalothorax, wheat bran, soy isolate, freshwater plants – pondweed perfoliate, fish-vegetable ration, produced feeding staffs have been investigated. In researching samples of manufactured pelleted feeds the standard methods adopted in the animal feed industry have been used. The number of nitrogen-free extractives and energy value has been determined by calculation. The composition of fish-vegetable ration has been worked out. Some manufacturing inspection of fish-vegetable feed technology using proofing process has been carried out. The possibility of manufacturing on the basis of crushed fish waste of the company LLC "VES" and dry ingredients of fish-vegetable feed has been determined; the output of feed at water content of not more than 10 % is 43 % of feed mix based on the mass of directed waste equal to 84 %. The pilot batch of dry fish-vegetable feed has been investigated to establish quality indicators. It has been determined that fish-vegetable feed meets the requirements of GOST 10385–2014 "Combined feeding staffs for fishes. General specifications" as for main quality indicators and refers to economic grower for catfish and carp fish weighing more than 50 g. This reveals good palatability of the experimental batch of floating feed by carp fish species and African catfish. Thus, fish-vegetable feed manufacturing technology can be implemented in the production for processing secondary raw materials: waste from butchering fish by grinding, cooking, mixing with selected vegetable fillings which is waste of flour or grain processing industries and freshwater plants mowed annually during the reclamation works on the Volga delta.

Influence of feed/inoculum ratios and waste cooking oil content on the mesophilic anaerobic digestion of food waste.

Science.gov (United States)

Li, Yangyang; Jin, Yiying; Borrion, Aiduan; Li, Jinhui

2018-03-01

Information on the anaerobic digestion (AD) of food waste (FW) with different waste cooking oil contents is limited in terms of the effect of the initial substrate concentrations. In this work, batch tests were performed to evaluate the combined effects of waste cooking oil content (33-53%) and feed/inoculum (F/I) ratios (0.5-1.2) on biogas/methane yield, process stability parameters and organics reduction during the FW AD. Both waste cooking oil and the inoculation ratios were found to affect digestion parameters during the AD process start-up and the F/I ratio was the predominant factor affecting AD after the start-up phase. The possible inhibition due to acidification caused by volatile fatty acids accumulation, low pH values and long-chain fatty acids was reversible. The characteristics of the final digestate indicated a stable anaerobic system, whereas samples with F/I ratios ranging from 0.8 to 1.2 display higher propionic and valeric acid contents and high amounts of total ammonia nitrogen and free ammonia nitrogen. Overall, F/I ratios higher than 0.70 caused inhibition and resulted in low biogas/methane yields from the FW. Copyright © 2018 Elsevier Ltd. All rights reserved.

Utilization of shrimp industry waste in the formulation of tilapia (Oreochromis niloticus Linnaeus) feed.

Science.gov (United States)

Oliveira Cavalheiro, José Marcelino; Oliveira de Souza, Erivelto; Bora, Pushkar Singh

2007-02-01

A rapid expansion of fisheries is demanding an adequate supply of efficient, nutritious and inexpensive fish feed, because feed contributes highly to the cost of fish production. Shrimp head, a waste product from the shrimp export industry qualifies as an economical, abundant and good quality protein source for fish feeds. In the present work, shrimp head silage powder, which contained approximately 40% protein, was used as a substitute for fish flour. Four feeds, in the form of pellets, were prepared by substituting shrimp head silage for fish flour at 0%, 33.3%, 66.6% and 100% dietary levels. Other ingredients such as corn, soy, bovine blood, cassava and corn cob flours, soy oil, vitamin premix, salt, and other components also were used in the formulation. A commercial fish feed was used as the control. The proximate composition of these feeds did not differ significantly at p>0.05, except for the protein content of the control feed, which was about 30.6% versus 35.4-36.9% protein in the other diets. No significant differences (p>0.05 level) in weight and length of juveniles fed with the different feeds during a period of 60 days were observed. In all cases, an excellent correlation (0.9950-0.9996) between weight and length of juveniles was observed. No significant difference in growth of juveniles fed on R1, R2, R3, or R4, or the control feed, was observed. Similarly, the proximate analyses of the flesh of juveniles did not present significant differences (p>0.05). The result of the study indicates that the shrimp head silage could replace fish flour as an ingredient in tilapia feed with economic advantages and without sacrificing the quality of the feed.

River Protection Double-Shell Tank Waste Retrieval Authorization Basis Amendment Task Plan

International Nuclear Information System (INIS)

HARRIS, J.P.

2000-01-01

This task plan is a documented agreement between Nuclear Safety and Licensing and Retrieval Engineering. The purpose of this task plan is to identify the scope of work, tasks and deliverables, responsibilities, manpower, and schedules associated with an authorization basis amendment as a result of the Waste Feed Delivery Program, Project W-211, Project W-521, and Project W-522

Comparison of fermented animal feed and mushroom growth media as two value-added options for waste Cassava pulp management.

Science.gov (United States)

Trakulvichean, Sivalee; Chaiprasert, Pawinee; Otmakhova, Julia; Songkasiri, Warinthorn

2017-12-01

Cassava is one of the main processed crops in Thailand, but this generates large amounts (7.3 million tons in 2015) of waste cassava pulp (WCP). The solid WCP is sold directly to farmers or pulp-drying companies at a low cost to reduce the burden of on-site waste storage. Using an integrated direct and environmental cost model, fermented animal feed and mushroom growth media were compared as added-value waste management alternatives for WCP to mitigate environmental problems. Primary and secondary data were collected from the literature, field data, and case studies. Data boundaries were restricted to a gate-to-gate scenario with a receiving capacity of 500 t WCP/d, and based on a new production unit being set up at the starch factory. The total production cost of each WCP utilization option was analyzed from the economic and environmental costs. Fermented animal feed was an economically attractive scenario, giving a higher net present value (NPV), lower investment cost and environmental impact, and a shorter payback period for the 10-year operational period. The selling price of mushrooms was the most sensitive parameter regarding the NPV, while the NPV for the price of fermented animal feed had the highest value in the best-case scenario.

At-tank Low-Activity Feed Homogeneity Analysis Verification

International Nuclear Information System (INIS)

DOUGLAS, J.G.

2000-01-01

This report evaluates the merit of selecting sodium, aluminum, and cesium-137 as analytes to indicate homogeneity of soluble species in low-activity waste (LAW) feed and recommends possible analytes and physical properties that could serve as rapid screening indicators for LAW feed homogeneity. The three analytes are adequate as screening indicators of soluble species homogeneity for tank waste when a mixing pump is used to thoroughly mix the waste in the waste feed staging tank and when all dissolved species are present at concentrations well below their solubility limits. If either of these conditions is violated, then the three indicators may not be sufficiently chemically representative of other waste constituents to reliably indicate homogeneity in the feed supernatant. Additional homogeneity indicators that should be considered are anions such as fluoride, sulfate, and phosphate, total organic carbon/total inorganic carbon, and total alpha to estimate the transuranic species. Physical property measurements such as gamma profiling, conductivity, specific gravity, and total suspended solids are recommended as possible at-tank methods for indicating homogeneity. Indicators of LAW feed homogeneity are needed to reduce the U.S. Department of Energy, Office of River Protection (ORP) Program's contractual risk by assuring that the waste feed is within the contractual composition and can be supplied to the waste treatment plant within the schedule requirements

Backcasting to identify food waste prevention and mitigation opportunities for infant feeding in maternity services.

Science.gov (United States)

Ryan-Fogarty, Yvonne; Becker, Genevieve; Moles, Richard; O'Regan, Bernadette

2017-03-01

Food waste in hospitals is of major concern for two reasons: one, healthcare needs to move toward preventative and demand led models for sustainability and two, food system sustainability needs to seek preventative measures such as diet adaptation and waste prevention. The impact of breast-milk substitute use on health services are well established in literature in terms of healthcare implications, cost and resourcing, however as a food demand and waste management issue little has been published to date. This paper presents the use of a desk based backcasting method to analyse food waste prevention, mitigation and management options within the Irish Maternity Service. Best practice in healthcare provision and waste management regulations are used to frame solutions. Strategic problem orientation revealed that 61% of the volume of ready to use breast-milk substitutes purchased by maternity services remains unconsumed and ends up as waste. Thirteen viable strategies to prevent and manage this waste were identified. Significant opportunities exist to prevent waste and also decrease food demand leading to both positive health and environmental outcomes. Backcasting methods display great promise in delivering food waste management strategies in healthcare settings, especially where evidenced best practice policies exist to inform solution forming processes. In terms of food waste prevention and management, difficulties arise in distinguishing between demand reduction, waste prevention and waste reduction measures under the current Waste Management Hierarchy definitions. Ultimately demand reduction at source requires prioritisation, a strategy which is complimentary to health policy on infant feeding. Copyright © 2016 Elsevier Ltd. All rights reserved.

Effects of feed process variables on Hanford Vitrification Plant performance

International Nuclear Information System (INIS)

Farnsworth, R.K.; Peterson, M.E.; Wagner, R.N.

1987-01-01

As a result of nuclear defense activities, high-level liquid radioactive wastes have been generated at the Hanford Site for over 40 yr. The Hanford Waste Vitrification Plant (HWVP) is being proposed to immobilize these wastes in a waste form suitable for disposal in a geologic repository. Prior to vitrification, the waste will undergo several conditioning steps before being fed to the melter. The effect of certain process variables on the resultant waste slurry properties must be known to assure processability of the waste slurry during feed preparation. Of particular interest are the rheological properties, which include the yield stress and apparent viscosity. Identification of the rheological properties of the slurry is required to adequately design the process equipment used for feed preparation (agitators, mixing tanks, concentrators, etc.). Knowledge of the slurry rheological properties is also necessary to establish processing conditions and operational limits for maximum plant efficiency and reliability. A multivariable study was performed on simulated HWVP feed to identify the feed process variables that have a significant impact on rheology during processing. Two process variables were evaluated in this study: (a) the amount of formic acid added to the feed and (b) the degree of shear encountered by the feed during processing. The feed was physically and rheologically characterized at various stages during feed processing

Application of wet waste from shrimp ( Litopenaeus vannamei) with or without sea mud to feeding sea cucumber ( Stichopus monotuberculatus)

Science.gov (United States)

Chen, Yanfeng; Hu, Chaoqun; Ren, Chunhua

2015-02-01

In the present study, the applicability of the wet waste collected from shrimp ( Litopenaeus vannamei) to the culture of sea cucumber ( Stichopus monotuberculatus) was determined. The effects of dietary wet shrimp waste on the survival, specific growth rate (SGR), fecal production rate (FPR), ammonia- and nitrite-nitrogen productions of sea cucumber were studied. The total organic matter (TOM) level in the feces of sea cucumber was compared with that in corresponding feeds. Diet C (50% wet shrimp waste and 50% sea mud mash) made sea cucumber grow faster than other diets. Sea cucumber fed with either diet D (25% wet shrimp waste and 75% sea mud mash) or sole sea mud exhibited negative growth. The average lowest total FPR of sea cucumber occurred in diet A (wet shrimp waste), and there was no significant difference in total FPR between diet C and diet E (sea mud mash) ( P > 0.05). The average ammonia-nitrogen production of sea cucumber in different diet treatments decreased gradually with the decrease of crude protein content in different diets. The average highest nitrite-nitrogen production occurred in diet E treatment, and there was no significant difference in nitrite-nitrogen production among diet A, diet B (75% wet shrimp waste and 25% sea mud mash) and diet C treatments ( P > 0.05). In each diet treatment, the total organic matter (TOM) level in feces decreased to different extent compared with that in corresponding feeds.

Hydrodeoxygenation of waste fat for diesel production: Study on model feed with Pt/alumina catalyst

DEFF Research Database (Denmark)

Madsen, Anders Theilgaard; Ahmed, El Hadi; Christensen, Claus H.

2011-01-01

Hydrodeoxygenation of waste fats and oils is a viable method for producing renewable diesel oil. In this study a model feed consisting of oleic acid and tripalmitin in molar ratio 1:3 was hydrotreated at 325°C with 20bars H2 in a stirred batch autoclave with a 5wt% Pt/γ-Al2O3 catalyst, and samples...

Influence of number of deliveries and total breast-feeding time on bone mineral density in premenopausal and young postmenopausal women.

Science.gov (United States)

Tsvetov, Gloria; Levy, Sigal; Benbassat, Carlos; Shraga-Slutzky, Ilana; Hirsch, Dania

2014-03-01

Pregnancy and lactation have been associated with decline in bone mineral density (BMD). It is not clear if there is a full recovery of BMD to baseline. This study sought to determine if pregnancy or breast-feeding or both have a cumulative effect on BMD in premenopausal and early postmenopausal women. We performed single-center cohort analysis. Five hundred women aged 35-55 years underwent routine BMD screening from February to July 2011 at a tertiary medical center. Patients were questioned about number of total full-term deliveries and duration of breast-feeding and completed a background questionnaire on menarche and menopause, smoking, dairy product consumption, and weekly physical exercise. Weight and height were measured. Dual-energy X-ray absorptiometry was used to measure spinal, dual femoral neck, and total hip BMD. Associations between background characteristics and BMD values were analyzed. Sixty percent of the women were premenopausal. Mean number of deliveries was 2.5 and mean duration of breast-feeding was 9.12 months. On univariate analysis, BMD values were negatively correlated with patient age (p=0.006) and number of births (p=0.013), and positively correlated with body mass index (posteoporosis later in life. Copyright © 2013 Elsevier Ireland Ltd. All rights reserved.

Waste glass melting stages

International Nuclear Information System (INIS)

Anderson, L.D.; Dennis, T.; Elliott, M.L.; Hrma, P.

1993-04-01

Three different simulated nuclear waste glass feeds, consisting of dried waste and glass frit, were heat treated for 1 hour in a gradient furnace at temperatures ranging from approximately 600 degrees C--1000 degrees C. Simulated melter feeds from the Hanford Waste Vitrification Plant (HWVP), the Defense Waste Processing Facility (DWPF), and Kernforschungszentrum Karlsruhe (KfK) in Germany were used. The samples were thin-sectioned and examined by optical microscopy to investigate the stages of the conversion from feed to glass. Various phenomena were seen, such as frit softening, bubble formation, foaming, bubble motion and removal, convective mixing, and homogenization. Behavior of different feeds was similar, although the degree of gas generation and melt homogenization varied

Thermoradiation treatment of sewage sludge using reactor waste to obtain acceptable fertilizer or animal supplement feed

International Nuclear Information System (INIS)

Sivinski, H.D.

1976-01-01

This document is a report of the Beneficial Uses Program. This program consists of a number of activities at Sandia Laboratories to develop the necessary technology for cost-beneficial use of a maximum amount of radioactive waste. Major activity is currently concentrated in the Waste Resources Utilization Program which has as its objective the use of cesium-134/137 as a gamma radiation source, coupled with modest heating, to treat sewage sludge to rid it of pathogenic organisms so that it may safely be used as a fertilizer or a feed supplement for ruminant animals. (author)

System Performance Testing of the Pulse-Echo Ultrasonic Instrument for Critical Velocity Determination during Hanford Tank Waste Transfer Operations - 13584

Energy Technology Data Exchange (ETDEWEB)

Denslow, Kayte M.; Bontha, Jagannadha R.; Adkins, Harold E.; Jenks, Jeromy W.J.; Hopkins, Derek F. [Pacific Northwest National Laboratory, Richland, Washington 99354 (United States); Thien, Michael G.; Kelly, Steven E.; Wooley, Theodore A. [Washington River Protection Solutions, Richland, Washington 99354 (United States)

2013-07-01

The delivery of Hanford double-shell tank waste to the Hanford Tank Waste Treatment and Immobilization Plant (WTP) is governed by specific Waste Acceptance Criteria that are identified in ICD 19 - Interface Control Document for Waste Feed. Waste must be certified as acceptable before it can be delivered to the WTP. The fluid transfer velocity at which solid particulate deposition occurs in waste slurry transport piping (critical velocity) is a key waste acceptance parameter that must be accurately characterized to determine if the waste is acceptable for transfer to the WTP. Washington River Protection Solutions and the Pacific Northwest National Laboratory have been evaluating the ultrasonic PulseEcho instrument since 2010 for its ability to detect particle settling and determine critical velocity in a horizontal slurry transport pipeline for slurries containing particles with a mean particle diameter of =14 micrometers (μm). In 2012 the PulseEcho instrument was further evaluated under WRPS' System Performance test campaign to identify critical velocities for slurries that are expected to be encountered during Hanford tank waste retrieval operations or bounding for tank waste feed. This three-year evaluation has demonstrated the ability of the ultrasonic PulseEcho instrument to detect the onset of critical velocity for a broad range of physical and rheological slurry properties that are likely encountered during the waste feed transfer operations between the Hanford tank farms and the WTP. (authors)

Replacing fish meal by food waste in feed pellets to culture lower trophic level fish containing acceptable levels of organochlorine pesticides: health risk assessments.

Science.gov (United States)

Cheng, Zhang; Mo, Wing-Yin; Man, Yu-Bon; Nie, Xiang-Ping; Li, Kai-Bing; Wong, Ming-Hung

2014-12-01

The present study used food waste (collected from local hotels and restaurants) feed pellets in polyculture of low-trophic level fish [bighead (Aristichtys nobilis), grass carp (Ctenopharyngodon idellus), and mud carp (Cirrhina molitorella)] aiming at producing safe and quality products for local consumption. The results indicated that grass carp (hexachlorocyclohexanes (HCHs) waste feed pellets were relatively free of organochlorine pesticides (OCPs). The experimental ponds (water and sediment) were relatively free of OCPs, lowering the possibility of biomagnification of OCPs in the food chains within the ponds. The raw concentrations of OCPs extracted from the fish were not in the bioavailable form, which would ultimately reach bloodstream and exert adverse effects on human body. Health risk assessments based on digestible concentrations are commonly regarded as a more accurate method. The results of health risk assessments based on raw and digestible concentrations showed that the fish fed with food waste feed pellets were safe for consumption from the OCP perspective. Copyright © 2014 Elsevier Ltd. All rights reserved.

Effect of Feed Melting, Temperature History, and Minor Component Addition on Spinel Crystallization in High-Level Waste Glass

Czech Academy of Sciences Publication Activity Database

Izák, Pavel; Hrma, P.; Arey, B. W.; Plaisted, T. J.

2001-01-01

Roč. 289, 1-3 (2001), s. 17-29 ISSN 0022-3093 Grant - others:DOE(US) DE/06/76RL01830 Keywords : feed melting * crystalization * high-level waste glass Subject RIV: CI - Industrial Chemistry, Chemical Engineering Impact factor: 1.363, year: 2001

Enteral feeding pumps: efficacy, safety, and patient acceptability

Directory of Open Access Journals (Sweden)

White H

2014-08-01

Full Text Available Helen White, Linsey King Nutrition and Dietetic Group, School of Health and Wellbeing, Faculty Health and Social Science, Leeds Metropolitan University, Leeds, United Kingdom Abstract: Enteral feeding is a long established practice across pediatric and adult populations, to enhance nutritional intake and prevent malnutrition. Despite recognition of the importance of nutrition within the modern health agenda, evaluation of the efficacy of how such feeds are delivered is more limited. The accuracy, safety, and consistency with which enteral feed pump systems dispense nutritional formulae are important determinants of their use and acceptability. Enteral feed pump safety has received increased interest in recent years as enteral pumps are used across hospital and home settings. Four areas of enteral feed pump safety have emerged: the consistent and accurate delivery of formula; the minimization of errors associated with tube misconnection; the impact of continuous feed delivery itself (via an enteral feed pump; and the chemical composition of the casing used in enteral feed pump manufacture. The daily use of pumps in delivery of enteral feeds in a home setting predominantly falls to the hands of parents and caregivers. Their understanding of the use and function of their pump is necessary to ensure appropriate, safe, and accurate delivery of enteral nutrition; their experience with this is important in informing clinicians and manufacturers of the emerging needs and requirements of this diverse patient population. The review highlights current practice and areas of concern and establishes our current knowledge in this field. Keywords: nutrition, perceptions, experience

Formulation and preparation of Hanford Waste Treatment Plant direct feed low activity waste Effluent Management Facility core simulant

Energy Technology Data Exchange (ETDEWEB)

McCabe, Daniel J. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Nash, Charles A. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL; Adamson, Duane J. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL

2016-05-01

The Hanford Waste Treatment and Immobilization Plant (WTP) Low Activity Waste (LAW) vitrification facility will generate an aqueous condensate recycle stream (LAW Melter Off-Gas Condensate, LMOGC) from the off-gas system. The baseline plan for disposition of this stream during full WTP operations is to send it to the WTP Pretreatment Facility, where it will be blended with LAW, concentrated by evaporation and recycled to the LAW vitrification facility. However, during the Direct Feed LAW (DFLAW) scenario, planned disposition of this stream is to evaporate it in a new evaporator in the Effluent Management Facility (EMF) and then return it to the LAW melter. It is important to understand the composition of the effluents from the melter and new evaporator so that the disposition of these streams can be accurately planned and accommodated. Furthermore, alternate disposition of the LMOGC stream would eliminate recycling of problematic components, and would enable less integrated operation of the LAW melter and the Pretreatment Facilities. Alternate disposition would also eliminate this stream from recycling within WTP when it begins operations and would decrease the LAW vitrification mission duration and quantity of glass waste, amongst the other problems such a recycle stream present. This LAW Melter Off-Gas Condensate stream will contain components that are volatile at melter temperatures and are problematic for the glass waste form, such as halides and sulfate. Because this stream will recycle within WTP, these components accumulate in the Melter Condensate stream, exacerbating their impact on the number of LAW glass containers that must be produced. Diverting the stream reduces the halides and sulfate in the recycled Condensate and is a key outcome of this work. This overall program examines the potential treatment and immobilization of this stream to enable alternative disposal. The objective of this task was to formulate and prepare a simulant of the LAW Melter

Waste glass melting stages

International Nuclear Information System (INIS)

Anderson, L.D.; Dennis, T.; Elliott, M.L.; Hrma, P.

1994-01-01

Three simulated nuclear waste glass feeds, consisting of dried waste and glass frit, were heat treated for 1 hour in a gradient furnace at temperatures ranging from approximately 600 degrees C to 1000 degrees C. Simulated melter feeds from the Hanford Waste Vitrification Plant (HWVP), the Defense Waste Processing Facility (DWPF), and Kernforschungszentru Karlsruhe (KfK) in Germany were used. The samples were thin sectioned and examined by optical microscopy to investigate the stages of the conversion from feed to glass. Various phenomena were seen, such as frit softening, bubble formation, foaming, bubble motion and removal, convective mixing, and homogenization. The behavior of different feeds was similar, although the degree of gas generation and melt homogenization varied. 2 refs., 8 tabs

Performance requirements for the single-shell tank

International Nuclear Information System (INIS)

GRENARD, C.E.

1999-01-01

This document provides performance requirements for the waste storage and waste feed delivery functions of the Single-Shell Tank (SST) System. The requirements presented here in will be used as a basis for evaluating the ability of the system to complete the single-shell tank waste feed delivery mission. They will also be used to select the technology or technologies for retrieving waste from the tanks selected for the single-shell tank waste feed delivery mission, assumed to be 241-C-102 and 241-C-104. This revision of the Performance Requirements for the SST is based on the findings of the SST Functional Analysis, and are reflected in the current System Specification for the SST System

One System Integrated Project Team: Retrieval And Delivery Of The Hanford Tank Wastes For Vitrification In The Waste Treatment Plant

Energy Technology Data Exchange (ETDEWEB)

Harp, Benton J. [Department of Energy, Office of River Protection, Richland, Washington (United States); Kacich, Richard M. [Bechtel National, Inc., Richland, WA (United States); Skwarek, Raymond J. [Washington River Protection Solutions LLC, Richland, WA (United States)

2012-12-20

The One System Integrated Project Team (IPT) was formed in late 2011 as a way for improving the efficiency of delivery and treatment of highly radioactive waste stored in underground tanks at the U.S. Department of Energy's (DOE's) 586-square-mile Hanford Site in southeastern Washington State. The purpose of the One System IPT is to improve coordination and integration between the Hanford's Waste Treatment Plant (WTP) contractor and the Tank Operations Contractor (TOC). The vision statement is: One System is a WTP and TOC safety conscious team that, through integrated management and implementation of risk-informed decision and mission-based solutions, will enable the earliest start of safe and efficient treatment of Hanford's tank waste, to protect the Columbia River, environment and public. The IPT is a formal collaboration between Bechtel National, Inc. (BNI), which manages design and construction of the WTP for the U.S. Department of Energy's Office of River Protection (DOEORP), and Washington River Protection Solutions (WRPS), which manages the TOC for ORP. More than fifty-six (56) million gallons of highly radioactive liquid waste are stored in one hundred seventy-seven (177) aging, underground tanks. Most of Hanford's waste tanks - one hundred forty-nine (149) of them - are of an old single-shell tank (SST) design built between 1944 and 1964. More than sixty (60) of these tanks have leaked in the past, releasing an estimated one million gallons of waste into the soil and threatening the nearby Columbia River. There are another twenty-eight (28) new double-shelled tanks (DSTs), built from 1968 to 1986, that provide greater protection to the environment. In 1989, DOE, the U.S. Environmental Protection Agency (EPA), and the Washington State Department of Ecology (Ecology) signed a landmark agreement that required Hanford to comply with federal and state environmental standards. It also paved the way for agreements that set deadlines for retrieving the tank

One System Integrated Project Team: Retrieval And Delivery Of The Hanford Tank Wastes For Vitrification In The Waste Treatment Plant

International Nuclear Information System (INIS)

Harp, Benton J.; Kacich, Richard M.; Skwarek, Raymond J.

2012-01-01

The One System Integrated Project Team (IPT) was formed in late 2011 as a way for improving the efficiency of delivery and treatment of highly radioactive waste stored in underground tanks at the U.S. Department of Energy's (DOE's) 586-square-mile Hanford Site in southeastern Washington State. The purpose of the One System IPT is to improve coordination and integration between the Hanford's Waste Treatment Plant (WTP) contractor and the Tank Operations Contractor (TOC). The vision statement is: One System is a WTP and TOC safety conscious team that, through integrated management and implementation of risk-informed decision and mission-based solutions, will enable the earliest start of safe and efficient treatment of Hanford's tank waste, to protect the Columbia River, environment and public. The IPT is a formal collaboration between Bechtel National, Inc. (BNI), which manages design and construction of the WTP for the U.S. Department of Energy's Office of River Protection (DOEORP), and Washington River Protection Solutions (WRPS), which manages the TOC for ORP. More than fifty-six (56) million gallons of highly radioactive liquid waste are stored in one hundred seventy-seven (177) aging, underground tanks. Most of Hanford's waste tanks - one hundred forty-nine (149) of them - are of an old single-shell tank (SST) design built between 1944 and 1964. More than sixty (60) of these tanks have leaked in the past, releasing an estimated one million gallons of waste into the soil and threatening the nearby Columbia River. There are another twenty-eight (28) new double-shelled tanks (DSTs), built from 1968 to 1986, that provide greater protection to the environment. In 1989, DOE, the U.S. Environmental Protection Agency (EPA), and the Washington State Department of Ecology (Ecology) signed a landmark agreement that required Hanford to comply with federal and state environmental standards. It also paved the way for agreements that set deadlines for retrieving the tank

One System Integrated Project Team: Retrieval and Delivery of Hanford Tank Wastes for Vitrification in the Waste Treatment Plant - 13234

International Nuclear Information System (INIS)

Harp, Benton J.; Kacich, Richard M.; Skwarek, Raymond J.

2013-01-01

The One System Integrated Project Team (IPT) was formed in late 2011 as a way for improving the efficiency of delivery and treatment of highly radioactive waste stored in underground tanks at the U.S. Department of Energy's (DOE's) 586-square-mile Hanford Site in southeastern Washington State. The purpose of the One System IPT is to improve coordination and integration between the Hanford's Waste Treatment Plant (WTP) contractor and the Tank Operations Contractor (TOC). The vision statement is: One System is a WTP and TOC safety-conscious team that, through integrated management and implementation of risk-informed decision and mission-based solutions, will enable the earliest start of safe and efficient treatment of Hanford's tank waste, to protect the Columbia River, environment and public. The IPT is a formal collaboration between Bechtel National, Inc. (BNI), which manages design and construction of the WTP for the U.S. Department of Energy's Office of River Protection (DOEORP), and Washington River Protection Solutions (WRPS), which manages the TOC for ORP. More than fifty-six (56) million gallons of highly radioactive liquid waste are stored in one hundred seventy-seven (177) aging, underground tanks. Most of Hanford's waste tanks - one hundred forty-nine (149) of them - are of an old single-shell tank (SST) design built between 1944 and 1964. More than sixty (60) of these tanks have leaked in the past, releasing an estimated one million gallons of waste into the soil and threatening the nearby Columbia River. There are another twenty-eight (28) new double-shelled tanks (DSTs), built from 1968 to 1986, that provide greater protection to the environment. In 1989, DOE, the U.S. Environmental Protection Agency (EPA), and the Washington State Department of Ecology (Ecology) signed a landmark agreement that required Hanford to comply with federal and state environmental standards. It also paved the way for agreements that set deadlines for retrieving the tank

One System Integrated Project Team: Retrieval and Delivery of Hanford Tank Wastes for Vitrification in the Waste Treatment Plant - 13234

Energy Technology Data Exchange (ETDEWEB)

Harp, Benton J. [U.S. Department of Energy, Office of River Protection, Post Office Box 550, Richland, Washington 99352 (United States); Kacich, Richard M. [Bechtel National, Inc., 2435 Stevens Center Place, Richland, Washington 99354 (United States); Skwarek, Raymond J. [Washington River Protection Solutions LLC, Post Office Box 850, Richland, Washington 99352 (United States)

2013-07-01

The One System Integrated Project Team (IPT) was formed in late 2011 as a way for improving the efficiency of delivery and treatment of highly radioactive waste stored in underground tanks at the U.S. Department of Energy's (DOE's) 586-square-mile Hanford Site in southeastern Washington State. The purpose of the One System IPT is to improve coordination and integration between the Hanford's Waste Treatment Plant (WTP) contractor and the Tank Operations Contractor (TOC). The vision statement is: One System is a WTP and TOC safety-conscious team that, through integrated management and implementation of risk-informed decision and mission-based solutions, will enable the earliest start of safe and efficient treatment of Hanford's tank waste, to protect the Columbia River, environment and public. The IPT is a formal collaboration between Bechtel National, Inc. (BNI), which manages design and construction of the WTP for the U.S. Department of Energy's Office of River Protection (DOEORP), and Washington River Protection Solutions (WRPS), which manages the TOC for ORP. More than fifty-six (56) million gallons of highly radioactive liquid waste are stored in one hundred seventy-seven (177) aging, underground tanks. Most of Hanford's waste tanks - one hundred forty-nine (149) of them - are of an old single-shell tank (SST) design built between 1944 and 1964. More than sixty (60) of these tanks have leaked in the past, releasing an estimated one million gallons of waste into the soil and threatening the nearby Columbia River. There are another twenty-eight (28) new double-shelled tanks (DSTs), built from 1968 to 1986, that provide greater protection to the environment. In 1989, DOE, the U.S. Environmental Protection Agency (EPA), and the Washington State Department of Ecology (Ecology) signed a landmark agreement that required Hanford to comply with federal and state environmental standards. It also paved the way for agreements that set deadlines

Effective utilization of distiller's grain soluble-an agro-industrial waste in the feed of cage-reared minor carp Labeo bata in a tropical reservoir, India.

Science.gov (United States)

Hassan, M A; Aftabuddin, Md; Meena, D K; Mishal, P; Gupta, S Das

2016-08-01

A 60-day feeding trial was conducted to evaluate the efficacy of distiller's grain soluble (brewery waste) as a prospective ingredient to substitute expensive and high demand feed component, soybean meal for farming Labeo bata in cages installed in tropical reservoir. Two isonitrogenous and isocaloric diets comprising brewery waste (49.2 % CP) as test diet and soybean meal (44.4 % CP) as reference diet were formulated and extruded to obtain 2-mm floating pellets. The efficacy of the diets was tested in terms of survival (%), live weight gain (%), SGR (%/day), FCR, PER and ANPU and recorded 65 ± 0.2, 96 ± 8.1, 1.9 ± 0.1, 2.5 ± 0.02, 1.4 ± 0.1, 20.3 ± 2.0 and 66 ± 0.6, 112 ± 9.8, 2.2 ± 0.1, 2.2 ± 0.2, 1.6 ± 0.1 and 20 ± 2.1, respectively, for soybean and brewer's waste-based formulated feed. The analyses of results revealed that survival, growth parameters and biochemical composition of whole body tissue did not differ significantly (p > 0.05) despite complete replacement of soybean meal by brewery waste. However, the cost estimate of diet revealed marked reduction of feed cost of Rs. 9.2/kg (33.8 %) in the test diet as compared to the reference diet. The study suggests that brewery waste could effectively replace soybean meal without effecting survival and growth of the fish. The finding thus may pave a productive way for reducing environmental pressure of disposal of an agro-industrial waste.

Determination of heat conductivity and thermal diffusivity of waste glass melter feed: Extension to high temperatures

International Nuclear Information System (INIS)

Rice, Jarrett A.; Pokorny, Richard; Schweiger, Michael J.; Hrma, Pavel R.

2014-01-01

The heat conductivity (λ) and the thermal diffusivity (a) of reacting glass batch, or melter feed, control the heat flux into and within the cold cap, a layer of reacting material floating on the pool of molten glass in an all-electric continuous waste glass melter. After previously estimating λ of melter feed at temperatures up to 680 deg C, we focus in this work on the λ(T) function at T > 680 deg C, at which the feed material becomes foamy. We used a customized experimental setup consisting of a large cylindrical crucible with an assembly of thermocouples, which monitored the evolution of the temperature field while the crucible with feed was heated at a constant rate from room temperature up to 1100°C. Approximating measured temperature profiles by polynomial functions, we used the heat transfer equation to estimate the λ(T) approximation function, which we subsequently optimized using the finite-volume method combined with least-squares analysis. The heat conductivity increased as the temperature increased until the feed began to expand into foam, at which point the conductivity dropped. It began to increase again as the foam turned into a bubble-free glass melt. We discuss the implications of this behavior for the mathematical modeling of the cold cap

X-ray tomography of feed-to-glass transition of simulated borosilicate waste glasses

International Nuclear Information System (INIS)

Harris, William H.; Guillen, Donna P.; Klouzek, Jaroslav; Pokorny, Richard; Yano, Tetsuji

2017-01-01

The feed composition of a high level nuclear waste (HLW) glass melter affects the overall melting rate by influencing the chemical, thermophysical, and morphological properties of a relatively insulating cold cap layer over the molten phase where the primary feed vitrification reactions occur. Data from X ray computed tomography imaging of melting pellets comprised of a simulated high-aluminum HLW feed heated at a rate of 10°C/min reveal the distribution and morphology of bubbles, collectively known as primary foam, within this layer for various SiO 2 /(Li 2 CO 3 +H 3 BO 3 +Na 2 CO 3 ) mass fractions at temperatures between 600°C and 1040°C. To track melting dynamics, cross-sections obtained through the central profile of the pellet were digitally segmented into primary foam and a condensed phase. Pellet dimensions were extracted using Photoshop CS6 tools while the DREAM.3D software package was used to calculate pellet profile area, average and maximum bubble areas, and two-dimensional void fraction. The measured linear increase in the pellet area expansion rates – and therefore the increase in batch gas evolution rates – with SiO 2 /(Li 2 CO 3 +H 3 BO 3 +Na 2 CO 3 ) mass fraction despite an exponential increase in viscosity of the final waste glass at 1050°C and a lower total amount of gas-evolving species suggest that the retention of primary foam with large average bubble size at higher temperatures results from faster reaction kinetics rather than increased viscosity. However, viscosity does affect the initial foam collapse temperature by supporting the growth of larger bubbles. Because the maximum bubble size is limited by the pellet dimensions, larger scale studies are needed to understand primary foam morphology at high temperatures. This temperature-dependent morphological data can be used in future investigations to synthetically generate cold cap structures for use in models of heat transfer within a HLW glass melter.

Biogas feed analysis

OpenAIRE

Song, Yuan

2008-01-01

Biogas production is regarded as the best energy recovery process from wet organic solid wastes (WOSW). Feed composition, storage conditions and time will influence the compositions of feed to biogas processes. In this study, apple juice from Meierienes Juice factory was used as the model substrates to mimic the liquid phase that can be extracted from fruit or juice industry WOSW. A series of batch experiments were carried out with different initial feed concentrations (0, 1, 2, 5, 10 %) of a...

Continued Evaluation of the Pulse-Echo Ultrasonic Instrument for Critical Velocity Determination during Hanford Tank Waste Transfer Operations - 12518

Energy Technology Data Exchange (ETDEWEB)

Denslow, Kayte M.; Bontha, Jagannadha R.; Adkins, Harold E.; Jenks, Jeromy W.J.; Burns, Carolyn A.; Schonewill, Philip P.; Hopkins, Derek F. [Pacific Northwest National Laboratory, Richland, Washington 99354 (United States); Thien, Michael G.; Wooley, Theodore A. [Washington River Protection Solutions, Richland, Washington 99354 (United States)

2012-07-01

The delivery of Hanford double-shell tank waste to the Hanford Tank Waste Treatment and Immobilization Plant (WTP) will be governed by specific Waste Acceptance Criteria that are identified in ICD 19 - Interface Control Document for Waste Feed. Waste must be certified as acceptable before it can be delivered to the WTP. The fluid transfer velocity at which solid particulate deposition occurs in waste slurry transport piping (critical velocity) is a key waste parameter that must be accurately characterized to determine if the waste is acceptable for transfer to the WTP. In 2010 Washington River Protection Solutions and the Pacific Northwest National Laboratory began evaluating the ultrasonic PulseEcho instrument to accurately identify critical velocities in a horizontal slurry transport pipeline for slurries containing particles with a mean particle diameter of >50 micrometers. In 2011 the PulseEcho instrument was further evaluated to identify critical velocities for slurries containing fast-settling, high-density particles with a mean particle diameter of <15 micrometers. This two-year evaluation has demonstrated the ability of the ultrasonic PulseEcho instrument to detect the onset of critical velocity for a broad range of physical and rheological slurry properties that are likely encountered during the waste feed transfer operations between the Hanford tank farms and the WTP. (authors)

Breastfeeding is best feeding.

Science.gov (United States)

Cutting, W

1995-02-01

The traditional practice of breast feeding is the best means to make sure infants grow up healthy. It costs nothing. Breast milk contains antibodies and other substances which defend against disease, especially those linked to poor food hygiene and inadequate water and sanitation. In developing countries, breast fed infants are at least 14 times less likely to die from diarrhea than those who are not breast fed. Urbanization and promotion of infant formula undermine breast feeding. Even though infants up to age 4-6 months should receive only breast milk to remain as healthy as possible, infants aged less than 4-6 months often receive other milks or gruels. Attendance of health workers at delivery and their contact with mother-infant pairs after delivery are ideal opportunities to encourage mothers to breast feed. In fact, if health workers provide mothers skilled support with breast feeding, mothers are more likely to breast feed well and for a longer time. Health workers need counseling skills and firm knowledge of techniques on breast feeding and of how to master common difficulties to help mothers with breast feeding. Listening skills and confidence building skills are also needed. Good family and work place support allows women in paid employment outside the home to continue breast feeding. Breast feeding is very important in emergency situations where access to water, sanitation, food, and health care is limited (e.g., refugee camps). In these situations, health workers should especially be aware of women's ability to breast feed and to support their breast feeding. HIV can be transmitted to nursing infants from HIV infected mothers. Yet one must balance this small risk against the possibility of contracting other serious infections (e.g., diarrhea) through alternative infant feeding, particularly if there is no access to potable water and sanitation.

Association between Caesarean Delivery and Isolated Doses of Formula Feeding in Cow Milk Allergy.

Science.gov (United States)

Gil, Francisco; Amezqueta, Ana; Martinez, Diana; Aznal, Elena; Etayo, Veronica; Durá, Teodoro; Sánchez-Valverde, Félix

2017-01-01

Cow milk allergy (CMA) is the most common food allergy in breastfed infants. The aim of this study is to verify whether certain perinatal factors may influence the development of CMA immunoglobulin E (IgE)+. A retrospective, observational study of case and control groups was carried out. Information was collected of patients with CMA IgE+ from our department during the years 1990-2013. Patients of the same age and sex were recruited for the control group. Information on the following variables was collected: sex, age, pregnancy tolerance, duration of pregnancy, type of delivery, isolated doses of formula feeding in hospital (FFH), duration of breastfeeding, and family history of allergy (defined as ≥1 first-degree family member with allergic disease). Statistical analysis was performed using multivariate logistic regression techniques. A total of 211 cases were included in this study. Multivariate analysis showed an influence of duration of breastfeeding, FFH to be a risk factor (OR 4.94; 95% CI 2.68-9.08), especially in caesarean delivery (OR 11.82; 95% CI 2.64-47.50), and prematurity (OR 0.29; 95% CI 0.09-0.92) to be a protective factor. Perinatal factors play a key role in the development of CMA IgE+, with an influence of breastfeeding duration, FFH and caesarean delivery as risk factors and prematurity as a protective factor. While family history had no important role, environmental factors were more decisive. © 2017 S. Karger AG, Basel.

Hanford Waste Physical and Rheological Properties: Data and Gaps

Energy Technology Data Exchange (ETDEWEB)

Wells, Beric E.; Kurath, Dean E.; Mahoney, Lenna A.; Onishi, Yasuo; Huckaby, James L.; Cooley, Scott K.; Burns, Carolyn A.; Buck, Edgar C.; Tingey, Joel M.; Daniel, Richard C.; Anderson, K. K.

2011-08-01

The Hanford Site in Washington State manages 177 underground storage tanks containing approximately 250,000 m3 of waste generated during past defense reprocessing and waste management operations. These tanks contain a mixture of sludge, saltcake and supernatant liquids. The insoluble sludge fraction of the waste consists of metal oxides and hydroxides and contains the bulk of many radionuclides such as the transuranic components and 90Sr. The saltcake, generated by extensive evaporation of aqueous solutions, consists primarily of dried sodium salts. The supernates consist of concentrated (5-15 M) aqueous solutions of sodium and potassium salts. The 177 storage tanks include 149 single-shell tanks (SSTs) and 28 double -hell tanks (DSTs). Ultimately the wastes need to be retrieved from the tanks for treatment and disposal. The SSTs contain minimal amounts of liquid wastes, and the Tank Operations Contractor is continuing a program of moving solid wastes from SSTs to interim storage in the DSTs. The Hanford DST system provides the staging location for waste feed delivery to the Department of Energy (DOE) Office of River Protection’s (ORP) Hanford Tank Waste Treatment and Immobilization Plant (WTP). The WTP is being designed and constructed to pretreat and then vitrify a large portion of the wastes in Hanford’s 177 underground waste storage tanks.

Melting characteristics of a plasma torch melter according to the waste feeding method

International Nuclear Information System (INIS)

Kim, T. W.; Choi, J. R.; Park, S. C.; Lu, C. S.; Park, J. K.; Hwang, T. W.; Shin, S. W.

2001-01-01

By using a batch type plasma torch melting system, continuous feeding and melting tests of non-combustible waste were executed. Using the results, the establishment of a heat transfer model and its verification were executed; the characteristics of the molten slag, exhaust gas, fly dust, volatilization of Cs, and leaching of slag were analyzed. In order to establish the heat transfer mode, the followings were considered; the electrical energy supplied to the plasma torch, the absorbed energy to the plasma torch for generating the plasma gas, the absorbed energy to the cooling water of the plasma torch, the energy supplied to the melter from the plasma gas by radiant heat, the energy loss through the exhaust gas, the waste melting energy, and the heating energy of an inner crucible and the melter. The concrete and soil were melted for the verification of the model. The waste was fed through waste feeder by the amount of 0.5kg or 1kg that was calculated by using the model. The experiment for the verification resulted in that the model was fitted well until the melter was heated sufficiently. If the electrical energy of 128kW were supplied to the plasma torch, energy balance of the plasma melting system was calculated with the model: the absorbed energy to the plasma torch for generating the plasma gas (27kW), the absorbed energy to the cooling water of the plasma torch (0∼ 36kW), the energy loss through the exhaust gas (5 ∼ 8kW), the waste melting energy (14kW), and the heating energy of an inner crucible and the melter (82 ∼ 43kW)

Erosion/corrosion concerns in feed preparation systems at the Defense Waste Processing Facility

International Nuclear Information System (INIS)

Gee, J.T.; Chandler, C.T.; Daugherty, W.L.; Imrich, K.J.; Jenkins, C.F.

1997-01-01

The Savannah River Site (SRS) has been operating a nuclear fuel cycle since the 1950's to produce nuclear materials in support of the national defense effort. The Department of Energy authorized the construction of the Defense Waste Processing Facility (DWPF) to immobilize the high level radioactive waste resulting from these processes as a durable borosilicate glass. The DWPF, after having undergone extensive testing, has been approved for operations and is currently immobilizing radioactive waste. To ensure reliability of the DWPF remote canyon processing equipment, a materials evaluation program was performed prior to radioactive operations to determine to what extent erosion/corrosion would impact design life of equipment. The program consisted of performing pre-service baseline inspections on critical equipment and follow-up inspections after completion of DWPF cold chemical demonstration runs. Non-destructive examination (NDE) techniques were used to assess erosion/corrosion as well as evaluation of corrosion coupon racks. These results were used to arrive at predicted equipment life for selected feed preparation equipment. It was concluded with the exception of the coil and agitator for the slurry mix evaporator (SME), which are exposed to erosive glass frit particles, all of the equipment should meet its design life

Techno-economic analysis of a food waste valorization process via microalgae cultivation and co-production of plasticizer, lactic acid and animal feed from algal biomass and food waste.

Science.gov (United States)

Kwan, Tsz Him; Pleissner, Daniel; Lau, Kin Yan; Venus, Joachim; Pommeret, Aude; Lin, Carol Sze Ki

2015-12-01

A techno-economic study of food waste valorization via fungal hydrolysis, microalgae cultivation and production of plasticizer, lactic acid and animal feed was simulated and evaluated by Super-Pro Designer®. A pilot-scale plant was designed with a capacity of 1 metric ton day(-1) of food waste with 20 years lifetime. Two scenarios were proposed with different products: Scenario (I) plasticizer & lactic acid, Scenario (II) plasticizer & animal feed. It was found that only Scenario I was economically feasible. The annual net profits, net present value, payback period and internal rate of return were US$ 422,699, US$ 3,028,000, 7.56 years and 18.98%, respectively. Scenario II was not economic viable due to a deficit of US$ 42,632 per year. Sensitivity analysis showed that the price of lactic acid was the largest determinant of the profitability in Scenario I, while the impact of the variables was very close in Scenario II. Copyright © 2015 Elsevier Ltd. All rights reserved.

ENGINEERING SPECIALTY ASSESSMENT OF TANK WASTE COMPATIBILITY REPORTING

International Nuclear Information System (INIS)

KNIGHT, M.A.

2003-01-01

This Engineering Specialty Assessment was conducted to review the Tank Farm Waste Transfer Compatibility Program to assess whether the program meets the needs of accelerated retrieval and closure and waste feed delivery and to identify areas and methods for streamlining the program. The assessment was conducted in June 2003 and resulted in two findings and thirteen observations. The assessment results indicate that significant opportunities exist for streamlining the program by reducing the number of criteria requiring evaluation from 21 to 11, with only six of the criteria requiring evaluation for the majority of transfers. The assessment identified areas where existing criteria require strengthening to ensure that the risks of undesirable solids precipitation, from either waste mixing or waste transfer, are minimized. The assessment further identified opportunities for using existing engineering tools to simplify the calculations involved with preparation of waste compatibility assessments. The need to ensure that a revision to the waste compatibility program is prepared to align the program criteria with those that will be implemented with the DSA approval was also identified. Finally, the assessment identified that corrective actions are required to implement a tank-by-tank PCB inventory within the Best Basis Inventory and to ensure that sample data from external waste generators is entered into the TWINS database

Urban governance and spatial inequality in service delivery: a case study of solid waste management in Abuja, Nigeria.

Science.gov (United States)

Adama, Onyanta

2012-09-01

Spatial inequality in service delivery is a common feature in African cities. Several factors account for the phenomenon but there is growing attention towards urban governance and the role of the state. Urban governance policies such as privatization serve as key strategies through which the state regulates and (re)produces spatial inequality in service delivery. This study examined how governance practices related to privatization and the regulatory role of the state reinforce spatial inequalities in the delivery of solid waste services in Abuja, Nigeria. It focused primarily on the issue of cost recovery. Privatization became a major focus in Abuja in 2003 when the government launched a pilot scheme. Although it has brought improvements in service delivery, privatization has also increased the gap in the quality of services delivered in different parts of the city. Drawing on empirical data, the study revealed that little sensitivity to income and affordability, and to income differentials between neighbourhoods in the fixing of user charges and in the choice of the billing method is contributing to spatial inequalities in service delivery. Furthermore, the study suggests that these practices are linked to a broader issue, a failure of the government to see the people as partners. It therefore calls for more inclusive governance especially in decision-making processes. The study also emphasizes the need for a policy document on solid waste management, as this would encourage a critical assessment of vital issues including how privatization is to be funded, especially in low-income areas.

HWVP NCAW melter feed rheology FY 1993 testing and analyses: Letter report

International Nuclear Information System (INIS)

Smith, P.A.

1996-03-01

The Hanford Waste Vitrification Plant (HWVP) program has been established to immobilize selected Hanford nuclear wastes before shipment to a geologic repository. The HWVP program is directed by the U.S. Department of Energy (DOE). The Pacific Northwest Laboratory (PNL) provides waste processing and vitrification technology to assist the design effort. The focus of this letter report is melter feed rheology, Process/Product Development, which is part of the Task in the PNL HWVP Technology Development (PHTD) Project. Specifically, the melter feed must be transported to the liquid fed ceramic melter (LFCM) to ensure HWVP operability and the manufacture of an immobilized waste form. The objective of the PHTD Project slurry flow technology development is to understand and correlate dilute and concentrated waste, formatted waste, waste with recycle addition, and melter feed transport properties. The objectives of the work described in this document were to examine frit effects and several processing conditions on melter feed rheology. The investigated conditions included boiling time, pH, noble metal containing melter feed, solids loading, and aging time. The results of these experiments contribute to the understanding of melter feed rheology. This document is organized in eight sections. This section provides the introductory remarks, followed by Section 2.0 that contains conclusions and recommendations. Section 3.0 reviews the scientific principles, and Section 4.0 details the experimental methods. The results and discussion and the review of related rheology data are in Sections 5.0 and 6.0, respectively. Section 7.0, an analysis of NCAW melter feed rheology data, provides an overall review of melter feed with FY 91 frit. References are included in Section 8.0. This letter report satisfies contractor milestone PHTD C93-03.02E, as described in the FY 1993 Pacific Northwest Hanford Laboratory Waste Plant Technology Development (PHTD) Project Work Plan

Targeted full energy and protein delivery in critically ill patients: a study protocol for a pilot randomised control trial (FEED Trial

Directory of Open Access Journals (Sweden)

Kate Fetterplace

2018-02-01

Full Text Available Abstract Background Current guidelines for the provision of protein for critically ill patients are based on incomplete evidence, due to limited data from randomised controlled trials. The present pilot randomised controlled trial is part of a program of work to expand knowledge about the clinical effects of protein delivery to critically ill patients. The primary aim of this pilot study is to determine whether an enteral feeding protocol using a volume target, with additional protein supplementation, delivers a greater amount of protein and energy to mechanically ventilated critically ill patients than a standard nutrition protocol. The secondary aims are to evaluate the potential effects of this feeding strategy on muscle mass and other patient-centred outcomes. Methods This prospective, single-centred, pilot, randomised control trial will include 60 participants who are mechanically ventilated and can be enterally fed. Following informed consent, the participants receiving enteral nutrition in the intensive care unit (ICU will be allocated using a randomisation algorithm in a 1:1 ratio to the intervention (high-protein daily volume-based feeding protocol, providing 25 kcal/kg and 1.5 g/kg protein or standard care (hourly rate-based feeding protocol providing 25 kcal/kg and 1 g/kg protein. The co-primary outcomes are the average daily protein and energy delivered to the end of day 15 following randomisation. The secondary outcomes include change in quadriceps muscle layer thickness (QMLT from baseline (prior to randomisation to ICU discharge and other nutritional and patient-centred outcomes. Discussion This trial aims to examine whether a volume-based feeding protocol with supplemental protein increases protein and energy delivery. The potential effect of such increases on muscle mass loss will be explored. These outcomes will assist in formulating larger randomised control trials to assess mortality and morbidity. Trial registration

Data Quality Objectives for WTP Feed Acceptance Criteria - 12043

Energy Technology Data Exchange (ETDEWEB)

Arakali, Aruna V.; Benson, Peter A.; Duncan, Garth; Johnston, Jill C.; Lane, Thomas A.; Matis, George; Olson, John W. [Hanford Tank Waste Treatment and Immobilization Plant (United States); Banning, Davey L.; Greer, Daniel A.; Seidel, Cary M.; Thien, Michael G. [Hanford Tank Operations Contractor - Washington River Protection Solutions, Richland, WA 99354 (United States)

2012-07-01

The Hanford Tank Waste Treatment and Immobilization Plant (WTP) is under construction for the U.S. Department of Energy by Bechtel National, Inc. and subcontractor URS Corporation (contract no. DE-AC27-01RV14136). The plant when completed will be the world's largest nuclear waste treatment facility. Bechtel and URS are tasked with designing, constructing, commissioning, and transitioning the plant to the long term operating contractor to process the legacy wastes that are stored in underground tanks (from nuclear weapons production between the 1940's and the 1980's). Approximately 56 million gallons of radioactive waste is currently stored in these tanks at the Hanford Site in southeastern Washington. There are three major WTP facilities being constructed for processing the tank waste feed. The Pretreatment (PT) facility receives feed where it is separated into a low activity waste (LAW) fraction and a high level waste (HLW) fraction. These fractions are transferred to the appropriate (HLW or LAW) facility, combined with glass former material, and sent to high temperature melters for formation of the glass product. In addition to PT, HLW and LAW, other facilities in WTP include the Laboratory (LAB) for analytical services and the Balance of Facilities (BOF) for plant maintenance, support and utility services. The transfer of staged feed from the waste storage tanks and acceptance in WTP receipt vessels require data for waste acceptance criteria (WAC) parameters from analysis of feed samples. The Data Quality Objectives (DQO) development was a joint team effort between WTP and Tank Operations Contractor (TOC) representatives. The focus of this DQO effort was to review WAC parameters and develop data quality requirements, the results of which will determine whether or not the staged feed can be transferred from the TOC to WTP receipt vessels. The approach involved systematic planning for data collection consistent with EPA guidance for the seven

Bio-processing of agro-byproducts to animal feed.

Science.gov (United States)

Ajila, C M; Brar, S K; Verma, M; Tyagi, R D; Godbout, S; Valéro, J R

2012-12-01

Agricultural and food-industry residues constitute a major proportion (almost 30%) of worldwide agricultural production. These wastes mainly comprise lignocellulosic materials, fruit and vegetable wastes, sugar-industry wastes as well as animal and fisheries refuse and byproducts. Agro-residues are rich in many bioactive and nutraceutical compounds, such as polyphenolics, carotenoids and dietary fiber among others. Agro residues are a major valuable biomass and present potential solutions to problems of animal nutrition and the worldwide supply of protein and calories, if appropriate technologies can be used for their valorization by nutrient enrichment. Technologies available for protein enrichment of these wastes include solid substrate fermentation, ensiling, and high solid or slurry processes. Technologies to be developed for the reprocessing of these wastes need to take account of the peculiarities of individual wastes and the environment in which they are generated, reprocessed, and used. In particular, such technologies need to deliver products that are safe, not just for animal feed use, but also from the perspective of human feeding. This review focuses on the major current applications of solid-state fermentation in relation to the feed sector.

Recovery of fissile materials from nuclear wastes

Science.gov (United States)

Forsberg, Charles W.

1999-01-01

A process for recovering fissile materials such as uranium, and plutonium, and rare earth elements, from complex waste feed material, and converting the remaining wastes into a waste glass suitable for storage or disposal. The waste feed is mixed with a dissolution glass formed of lead oxide and boron oxide resulting in oxidation, dehalogenation, and dissolution of metal oxides. Carbon is added to remove lead oxide, and a boron oxide fusion melt is produced. The fusion melt is essentially devoid of organic materials and halogens, and is easily and rapidly dissolved in nitric acid. After dissolution, uranium, plutonium and rare earth elements are separated from the acid and recovered by processes such as PUREX or ion exchange. The remaining acid waste stream is vitrified to produce a waste glass suitable for storage or disposal. Potential waste feed materials include plutonium scrap and residue, miscellaneous spent nuclear fuel, and uranium fissile wastes. The initial feed materials may contain mixtures of metals, ceramics, amorphous solids, halides, organic material and other carbon-containing material.

A biotechnological process for treatment and recycling poultry wastes manure as a feed ingredient

Energy Technology Data Exchange (ETDEWEB)

El Jalil, M.H. [Faculty of Sciences, Kenitra (Morocco). Biology Dept.; Hassan II Inst. of Agronomy and Veterinary Medicine, Rabat-Instituts (Morocco); Faid, M. [Hassan II Inst. of Agronomy and Veterinary Medicine, Rabat-Instituts (Morocco); Elyachioui, M. [Faculty of Sciences, Kenitra (Morocco)

2001-07-01

Poultry wastes manure was diluted by adding the same amount of water 50-50 (w/v). They were then mixed with 10% molasses. The mixture was inoculated with a starter culture of Lactobacillus plantarum and Pediococcus acidolactici, and incubated at 30{sup o}C for 10 days. Changes in nutritional quality and biochemical properties (pH, total nitrogen, total volatile nitrogen, non protein nitrogen, carbohydrates and ash) were determined for the raw and the transformed product. In parallel, microbiological analyses, including standard plant count, enterobacteria and enterococci, were performed. Results indicated that the product obtained from the wastes fermentation showed low counts of enterobacteria and enterococci. Chemical determinations showed a net decrease of the pH to around 4.0 and the growth curve of the lactic acid bacteria showed the success of the acidification process. The total nitrogen was conserved in the product and the total volatile nitrogen was totally eliminated. The product was used for substituting some protein sources in a conventional formula used in laying feeding of three lots. Two formulae containing, respectively, 20% and 40% of the product was compared to the control (0%). The food consumption and laying performances were monitored for 30 days. The nutritional test indicted that the incorporation of the poultry manure silage of up to 40% gave laying performances similar to those obtained with the conventional formula. These results show that it is possible to transform poultry manure by controlled fermentation and that the product has an added value as a feed ingredient. (Author)

Linking the poor to new modalities in service delivery. Partnership innovations in solid waste management in Bogotá, Colombia

NARCIS (Netherlands)

I. Turcotte (Isabelle); G.M. Gómez (Georgina)

2012-01-01

textabstractWaste picking has become a prominent activity in the urban landscape, bridging the gap between shortfalls in service delivery and personal income generation in virtually all cities of the developing world. Overcoming previous stigmatization and work fragmentation through organization and

Tank waste remediation system retrieval and disposal mission key enabling assumptions

International Nuclear Information System (INIS)

Baldwin, J.H.

1998-01-01

An overall systems approach has been applied to develop action plans to support the retrieval and immobilization waste disposal mission. The review concluded that the systems and infrastructure required to support the mission are known. Required systems are either in place or plans have been developed. An analysis of the programmatic, management and technical activities necessary to declare Readiness to Proceed with execution of the mission demonstrates that the system, people, and hardware will be on line and ready to support the private contractors. The systems approach included defining the retrieval and immobilized waste disposal mission requirements and evaluating the readiness of the TWRS contractor to supply waste feed to the private contractors in June 2002. The Phase 1 feed delivery requirements from the Private Contractor Request for Proposals were reviewed, transfer piping routes were mapped on it, existing systems were evaluated, and upgrade requirements were defined. Technical Basis Reviews were completed to define work scope in greater detail, cost estimates and associated year by year financial analyses were completed. Personnel training, qualifications, management systems and procedures were reviewed and shown to be in place and ready to support the Phase 1B mission. Key assumptions and risks that could negatively impact mission success were evaluated and appropriate mitigative actions plans were planned and scheduled

Assessment of nutritional value of single-cell protein from waste-activated sludge as a protein supplement in poultry feed.

Science.gov (United States)

Nkhalambayausi-Chirwa, Evans M; Lebitso, Moses T

2012-12-01

The amount of protein wasted through sludge in Gauteng, South Africa, amounts to 95 000 metric tonne/yr, with the order of magnitude of the national protein requirement of approximately 145 000 metric tonne/yr. Waste-activated sludge (WAS) from wastewater treatment plants (WWTPs) that treat domestic wastewater contains protein in a ratio of 2:1 against fishmeal. This protein source has not been utilized because of the high content of toxic heavy metals and other potential carcinogenic pollutants in the sludge. In this study, a pretreatment method of modified aqua regia dilute acid wash was used to lower the metal content by approximately 60%. However, this resulted in a 33% loss of amino acids in the acid-washed WAS. A feed substitution test in poultry with different fishmeal-sludge ratios (0%, 25%, 50%, 75%, and 100% WAS as percent substitution of fishmeal) showed no impact of sludge single-cell protein (SCP) on mortality rate. However, sludge substitution in the feed yielded weight gains and cost savings up to 46%.

Rheological Studies on Pretreated Feed and Melter Feed from AW-101 and AN-107

International Nuclear Information System (INIS)

Bredt, Paul R; Swoboda, Robert G

2001-01-01

Rheological and physical properties testing were conducted on actual AN-107 and AW-101 pretreated feed samples prior to the addition of glass formers. Analyses were repeated following the addition of glass formers. The AN-107 and AW-101 pretreated feeds were tested at the target sodium values of nominally 6, 8, and 10 M. The AW-101 melter feeds were tested at these same concentrations, while the AN-107 melter feeds were tested at 5, 6, and 8 M with respect to sodium. These data on actual waste are required to validate and qualify results obtained with simulants

Waste Transfer Leaks Control Decision Record

International Nuclear Information System (INIS)

RYAN, G.W.

2000-01-01

Control decision meetings for Waste Transfer Leaks were held on April 24,25,26, and 27, 2000. The agenda for the control decision meetings is included in Appendix A, and attendee lists are included in Appendix B. The purpose of the control decision meetings was to review and revise previously selected controls for the prevention or mitigation of waste transfer leak accidents. Re-evaluation of the controls is warranted due to revisions in the hazard and accident analysis for these Tank Farm events. In particular, calculated radiological consequences are significantly reduced from those currently reported in the Final Safety Analysis Report (FSAR). Revised hazard and accident analysis and a revised control recommendation will be reflected in an Authorization Basis Amendment to be submitted at the Department of Energy, Office of River Protection's (ORP's) request by June 30, 2000 to satisfy ORP Performance Incentive (PI) 2.1.1, Revision 1, ''Authorization Basis Management Process Efficiency Improvement''. The scope of the control decision meetings was to address all waste transfer leak-related hazardous conditions identified in the Tank Farm hazard analysis database, excluding those associated with the use of the Replacement Cross-Site Transfer System (RCSTS) slurry line and sluicing of Tank 241-C-106, which is addressed in FSAR Addendum 1. The scope of this control decision process does include future waste feed delivery waste transfer operations

Preliminary assessment of blending Hanford tank wastes

International Nuclear Information System (INIS)

Geeting, J.G.H.; Kurath, D.E.

1993-03-01

A parametric study of blending Hanford tank wastes identified possible benefits from blending wastes prior to immobilization as a high level or low level waste form. Track Radioactive Components data were used as the basis for the single-shell tank (SST) waste composition, while analytical data were used for the double-shell tank (DST) composition. Limiting components were determined using the existing feed criteria for the Hanford Waste Vitrification Plant (HWVP) and the Grout Treatment Facility (GTF). Results have shown that blending can significantly increase waste loading and that the baseline quantities of immobilized waste projected for the sludge-wash pretreatment case may have been drastically underestimated, because critical components were not considered. Alternatively, the results suggest further review of the grout feed specifications and the solubility of minor components in HWVP borosilicate glass. Future immobilized waste estimates might be decreased substantially upon a thorough review of the appropriate feed specifications

Preliminary assessment of blending Hanford tank wastes

Energy Technology Data Exchange (ETDEWEB)

Geeting, J.G.H.; Kurath, D.E.

1993-03-01

A parametric study of blending Hanford tank wastes identified possible benefits from blending wastes prior to immobilization as a high level or low level waste form. Track Radioactive Components data were used as the basis for the single-shell tank (SST) waste composition, while analytical data were used for the double-shell tank (DST) composition. Limiting components were determined using the existing feed criteria for the Hanford Waste Vitrification Plant (HWVP) and the Grout Treatment Facility (GTF). Results have shown that blending can significantly increase waste loading and that the baseline quantities of immobilized waste projected for the sludge-wash pretreatment case may have been drastically underestimated, because critical components were not considered. Alternatively, the results suggest further review of the grout feed specifications and the solubility of minor components in HWVP borosilicate glass. Future immobilized waste estimates might be decreased substantially upon a thorough review of the appropriate feed specifications.

Hanford Waste Transfer Planning and Control - 13465

Energy Technology Data Exchange (ETDEWEB)

Kirch, N.W.; Uytioco, E.M.; Jo, J. [Washington River Protection Solutions, LLC, Richland, Washington (United States)

2013-07-01

Hanford tank waste cleanup requires efficient use of double-shell tank space to support single-shell tank retrievals and future waste feed delivery to the Waste Treatment and Immobilization Plant (WTP). Every waste transfer, including single-shell tank retrievals and evaporator campaign, is evaluated via the Waste Transfer Compatibility Program for compliance with safety basis, environmental compliance, operational limits and controls to enhance future waste treatment. Mixed radioactive and hazardous wastes are stored at the Hanford Site on an interim basis until they can be treated, as necessary, for final disposal. Implementation of the Tank Farms Waste Transfer Compatibility Program helps to ensure continued safe and prudent storage and handling of these wastes within the Tank Farms Facility. The Tank Farms Waste Transfer Compatibility Program is a Safety Management Program that is a formal process for evaluating waste transfers and chemical additions through the preparation of documented Waste Compatibility Assessments (WCA). The primary purpose of the program is to ensure that sufficient controls are in place to prevent the formation of incompatible mixtures as the result of waste transfer operations. The program defines a consistent means of evaluating compliance with certain administrative controls, safety, operational, regulatory, and programmatic criteria and specifies considerations necessary to assess waste transfers and chemical additions. Current operations are most limited by staying within compliance with the safety basis controls to prevent flammable gas build up in the tank headspace. The depth of solids, the depth of supernatant, the total waste depth and the waste temperature are monitored and controlled to stay within the Compatibility Program rules. Also, transfer planning includes a preliminary evaluation against the Compatibility Program to assure that operating plans will comply with the Waste Transfer Compatibility Program. (authors)

Early elective cesarean delivery before 36 weeks vs late spontaneous delivery in infants with gastroschisis.

Science.gov (United States)

Hadidi, Ahmed; Subotic, Ulrike; Goeppl, Maximilian; Waag, Karl-L

2008-07-01

The aim of this study is to assess the value of early elective cesarean delivery for patients with gastroschisis in comparison with late spontaneous delivery. Analysis of infants with gastroschisis admitted between 1986 and 2006 at a tertiary care center was performed. The findings were analyzed statistically. Eighty-six patients were involved in the study. This included 15 patients who underwent emergency cesarean delivery (EM CD group) because of fetal distress and/or bowel ischemia. The remaining 71 patients born electively were stratified into 4 groups. The early elective cesarean delivery (ECD) group included 23 patients born by ECD before 36 weeks; late vaginal delivery (LVD) group included 23 patients who had LVD after 36 weeks; 24 patients had LCD after 36 weeks because of delayed diagnosis that resulted in late referral; and 1 patient had early spontaneous vaginal delivery (EVD group) before 36 weeks. The mean time to start oral feeding, incidence of complications, and primary closure were significantly better in the ECD group than in the LVD group. The duration of ventilation and the length of stay were shorter in ECD group, but the difference was not statistically significant. Elective cesarean delivery before 36 weeks allows earlier enteral feeding and is associated with less complications and higher incidence of primary closure (statistically significant).

The Effects of Amofer Palm Oil Waste-based Complete Feed to Blood Profiles and Liver Function on Local Sheep

Directory of Open Access Journals (Sweden)

Hamdi Mayulu

2012-04-01

Full Text Available Amoniation-Fermentation (amofer technology should be conducted in order to improve the low quality of by product produced from palm oil plantations and mills (palm oil waste which is used for constituent of feed ingredients in complete feed (CF. This technology also reforms the feed material into edible form. Before broadly applicable, it must be ensured that the feed does not have toxic effects on livestock. This research was peformed to evaluate the effects of amofer palm oil waste-based CF to blood profile and liver function on local sheep. Completely Randomly Design (CRD was used with 4 treaments and 4 replications. The observed variables were the levels of hemoglobin, hematocrit, blood glucose, ALT and AST was analyzed by ANOVA. The average value of blood glucose levels at T1= 80.68 mg/dl, T2=79.08 mg/dl, T3=81.18 mg/dl and T4=73.70 mg/dl. The average value of hemoglobin levels at T1=10.80 g/dl, T2=10.30 g/dl, T3=11.23 g/dl and T4=10.25 g/dl. The average value of hematocrit levels at T1=31.00%, T2=31.00%, T3=33.75% and T4=30%. The average value of ALT levels at T1=17.90 ml, T2=13.83 ml, T3=18.75 ml and, T4=13.40 ml. The average value of AST level at T1=106.20 ml, T2=88.98 ml, T3=104.40 ml and T4=91.25 ml. There was no significant difference among four treatments (p>0.05. The administration CF did not cause hematological disorders which showed by the blood profiles and liver function were in normal range, so that suggested the CF was appropriate and safe for local sheep. [Keywords––amofer, complete feed, hemoglobin, hematocrit, glucose, liver function

Effects of feeding level and feeding frequency on growth, feed efficiency and nitrogen and phosphorus loss in seabass (Lates calcarifer Bloch) fed diets with defatted soybean meal partially replacing fishmeal

OpenAIRE

Srisook, S.; Mahankich, S.; Tantikitti, C.; Onkong, S.

2007-01-01

Satun Coastal Fisheries Research and Development Center, Muang, Satun 3Feeding management is crucial for feed efficiency, nutrient utilization, growth of cultured aquatic species and the amount of organic waste produced. This study aimed at investigating effects of two levels offeeding at two feeding frequencies on growth performance, feed efficiency and nitrogen and phosphorus loss in Asian seabass when fed diets with defatted soybean meal (SBM) replacing fish meal. Three diets were formulat...

Statistical Methods and Tools for Hanford Staged Feed Tank Sampling

Energy Technology Data Exchange (ETDEWEB)

Fountain, Matthew S. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Brigantic, Robert T. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Peterson, Reid A. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

2013-10-01

This report summarizes work conducted by Pacific Northwest National Laboratory to technically evaluate the current approach to staged feed sampling of high-level waste (HLW) sludge to meet waste acceptance criteria (WAC) for transfer from tank farms to the Hanford Waste Treatment and Immobilization Plant (WTP). The current sampling and analysis approach is detailed in the document titled Initial Data Quality Objectives for WTP Feed Acceptance Criteria, 24590-WTP-RPT-MGT-11-014, Revision 0 (Arakali et al. 2011). The goal of this current work is to evaluate and provide recommendations to support a defensible, technical and statistical basis for the staged feed sampling approach that meets WAC data quality objectives (DQOs).

The DWPF waste form qualification program

International Nuclear Information System (INIS)

Marra, S.L.; Plodinec, M.J.

1994-01-01

Prior to the introduction of radioactive feed into the Defense Waste Processing Facility for immobilization in borosilicate glass an extensive waste qualification program must be completed. The DWPF must demonstrate its ability to comply with the Waste Acceptance Product Specifications. This ability is being demonstrated through laboratory and pilot scale work and will be completed after the full operation of the DWPF using various simulated feeds

Feed process studies: Research-Scale Melter

Energy Technology Data Exchange (ETDEWEB)

Whittington, K.F.; Seiler, D.K.; Luey, J.; Vienna, J.D.; Sliger, W.A.

1996-09-01

In support of a two-phase approach to privatizing the processing of hazardous and radioactive waste at Hanford, research-scale melter (RSM) experiments were conducted to determine feed processing characteristics of two potential privatization Phase 1 high-level waste glass formulations and to determine if increased Ag, Te, and noble metal amounts would have bad effects. Effects of feed compositions and process conditions were examined for processing rate, cold cap behavior, off-gas, and glass properties. The 2 glass formulations used were: NOM-2 with adjusted waste loading (all components except silica and soda) of 25 wt%, and NOM-3 (max waste loaded glass) with adjusted waste loading of 30 wt%. The 25 wt% figure is the minimum required in the privatization Request for Proposal. RSM operated for 19 days (5 runs). 1010 kg feed was processed, producing 362 kg glass. Parts of runs 2 and 3 were run at 10 to 30 degrees above the nominal temperature 1150 C, with the most significant processing rate increase in run 3. Processing observations led to the choice of NOM-3 for noble metal testing in runs 4 and 5. During noble metal testing, processing rates fell 50% from baseline. Destructive analysis showed that a layer of noble metals and noble metal oxides settled on the floor of the melter, leading to current ``channeling`` which allowed the top section to cool, reducing production rates.

Feed process studies: Research-Scale Melter

International Nuclear Information System (INIS)

Whittington, K.F.; Seiler, D.K.; Luey, J.; Vienna, J.D.; Sliger, W.A.

1996-09-01

In support of a two-phase approach to privatizing the processing of hazardous and radioactive waste at Hanford, research-scale melter (RSM) experiments were conducted to determine feed processing characteristics of two potential privatization Phase 1 high-level waste glass formulations and to determine if increased Ag, Te, and noble metal amounts would have bad effects. Effects of feed compositions and process conditions were examined for processing rate, cold cap behavior, off-gas, and glass properties. The 2 glass formulations used were: NOM-2 with adjusted waste loading (all components except silica and soda) of 25 wt%, and NOM-3 (max waste loaded glass) with adjusted waste loading of 30 wt%. The 25 wt% figure is the minimum required in the privatization Request for Proposal. RSM operated for 19 days (5 runs). 1010 kg feed was processed, producing 362 kg glass. Parts of runs 2 and 3 were run at 10 to 30 degrees above the nominal temperature 1150 C, with the most significant processing rate increase in run 3. Processing observations led to the choice of NOM-3 for noble metal testing in runs 4 and 5. During noble metal testing, processing rates fell 50% from baseline. Destructive analysis showed that a layer of noble metals and noble metal oxides settled on the floor of the melter, leading to current ''channeling'' which allowed the top section to cool, reducing production rates

Hanford Waste Vitrification Plant

International Nuclear Information System (INIS)

Larson, D.E.; Allen, C.R.; Kruger, O.L.; Weber, E.T.

1991-10-01

The Hanford Waste Vitrification Plant (HWVP) is being designed to immobilize pretreated Hanford high-level waste and transuranic waste in borosilicate glass contained in stainless steel canisters. Testing is being conducted in the HWVP Technology Development Project to ensure that adapted technologies are applicable to the candidate Hanford wastes and to generate information for waste form qualification. Empirical modeling is being conducted to define a glass composition range consistent with process and waste form qualification requirements. Laboratory studies are conducted to determine process stream properties, characterize the redox chemistry of the melter feed as a basis for controlling melt foaming and evaluate zeolite sorption materials for process waste treatment. Pilot-scale tests have been performed with simulated melter feed to access filtration for solids removal from process wastes, evaluate vitrification process performance and assess offgas equipment performance. Process equipment construction materials are being selected based on literature review, corrosion testing, and performance in pilot-scale testing. 3 figs., 6 tabs

Determinants of Prelacteal Feeding in Rural Northern India

Directory of Open Access Journals (Sweden)

Manas Pratim Roy

2014-01-01

Conclusions: The problem of prelacteal feeding is still prevalent in rural India. Age, caste, and place of delivery were associated with the problem. For ensuring neonatal health, the problem should be addressed with due gravity, with emphasis on exclusive breast feeding.

Effects of loading rate and temperature on anaerobic co-digestion of food waste and waste activated sludge in a high frequency feeding system, looking in particular at stability and efficiency.

Science.gov (United States)

Li, Qian; Li, Hao; Wang, Gaojun; Wang, Xiaochang

2017-08-01

A continuously stirred tank reactor (CSTR) with a high feeding frequency (HFF) of once every 15min was employed in order to ease the loading shock frequently occurred in digester with a low feeding frequency. The effects of the organic loading rate (OLR) and temperature on the co-digestion of food waste and waste activated sludge was evaluated in a 302-day long-term experiment. Due to the high hydrolysis rate, the maximum CH 4 yield in a thermophilic reactor was 407mL CH 4 /gVS added , a value that was significantly higher than the 350mL CH 4 /gVS added that occurred in a mesophilic reactor. Although the alkalinity declined when HRT was shorted than 10d, caused by the decrease of conversion ratio from protein to ammonium, the increase of specific methanogenic activity helped HFF system to achieve stable performance at an OLR of 11.2 (HRT 7.5d) and 30.2gVS/L/d (HRT 3d) under mesophilic and thermophilic conditions, respectively. Copyright © 2017 Elsevier Ltd. All rights reserved.

Application of the HWVP measurement error model and feed test algorithms to pilot scale feed testing

International Nuclear Information System (INIS)

Adams, T.L.

1996-03-01

The purpose of the feed preparation subsystem in the Hanford Waste Vitrification Plant (HWVP) is to provide, for control of the properties of the slurry that are sent to the melter. The slurry properties are adjusted so that two classes of constraints are satisfied. Processability constraints guarantee that the process conditions required by the melter can be obtained. For example, there are processability constraints associated with electrical conductivity and viscosity. Acceptability constraints guarantee that the processed glass can be safely stored in a repository. An example of an acceptability constraint is the durability of the product glass. The primary control focus for satisfying both processability and acceptability constraints is the composition of the slurry. The primary mechanism for adjusting the composition of the slurry is mixing the waste slurry with frit of known composition. Spent frit from canister decontamination is also recycled by adding it to the melter feed. A number of processes in addition to mixing are used to condition the waste slurry prior to melting, including evaporation and the addition of formic acid. These processes also have an effect on the feed composition

Preliminary assessment of nine waste-form products/processes for immobilizing transuranic wastes

International Nuclear Information System (INIS)

Crisler, L.R.

1980-09-01

Nine waste-form processes for reduction of the present and projected Transuranic (TRU) waste inventory to an immobilized product have been evaluated. Product formulations, selected properties, preparation methods, technology status, problem areas needing resolution and location of current research development being pursued in the United States are discussed for each process. No definitive utility ranking is attempted due to the early stage of product/process development for TRU waste containing products and the uncertainties in the state of current knowledge of TRU waste feed compositional and quantitative makeup. Of the nine waste form products/processes included in this discussion, bitumen and cements (encapsulation agents) demonstrate the degree of flexibility necessary to immobilize the wide composition range present in the TRU waste inventory. A demonstrated process called Slagging Pyrolysis Incineration converts a varied compositional feed (municipal wastes) to a ''basalt'' like product. This process/product appears to have potential for TRU waste immobilization. The remaining waste forms (borosilicate glass, high-silica glass, glass ceramics, ''SYNROC B'' and cermets) have potential for immobilizing a smaller fraction of the TRU waste inventory than the above discussed waste forms

Superconducting open-gradient magnetic separation for the pretreatment of radioactive or mixed waste vitrification feeds. 1998 annual progress report

International Nuclear Information System (INIS)

Crawford, C.; Doctor, R.D.; Landsberger, S.; Nunez, L.; Ritter, J.

1998-01-01

'The objective is to reduce the volume and cost of high-level waste glass produced during US DOE remediation activities by demonstrating that magnetic separation can separate crystalline, amorphous, and colloidal constituents in vitrification feed streams known to be deleterious to the production of borosilicate glass. Magnetic separation will add neither chemicals nor generate secondary waste streams. The project includes the systematic study of magnetic interactions of waste constituents under controlled physical and chemical conditions (e.g., hydration, oxidation, temperature) to identify mechanisms that control the magnetic properties. Partitioning of radionuclides to determine their sorption mechanisms is also being studied. The identification of fundamental magnetic properties within the microscopic chemical environment in combination with hydrodynamic and electrodynamic models provides insights into the design of a system for optimal separation. Following this, experimental studies using superconducting open-gradient magnetic separation (OGMS) will be conducted to validate its effectiveness as a pretreatment technique.'

The Utilization of Sago Waste as Cattle Feed

Science.gov (United States)

Tiro, B. M. W.; Beding, P. A.; Baliadi, Y.

2018-02-01

This study aimed was to evaluate nutrition value of sago waste and its effect on cattle performance.The collected data were analyzed using analysis of variance. The results of the study showed that of the utilization of sago waste had a positive effect on average daily gain (ADG), where with 2% sago waste of body weight (P2 treatment) gave the highest ADG 0.43 ± 0.02 kg/h/day and cattle which consumed only forage without sago waste (P0) gave the lowest ADG 0.26 ± 0.04 kg/h/day. Statistical analysis showed that the addition of sago waste significantly affected the ADG (P0.05), but significant affect(Pcattle.

Defense waste cyclone incinerator demonstration program: April-September 1980

International Nuclear Information System (INIS)

Klingler, L.M.

1981-01-01

An improved offgas system is being designed. The new system will improve gas cleaning and will also provide for improved offgas sampling and mass balance data collection. Continuous solid feed burning experiments were delayed pending delivery of shredding equipment. Liquid burning experiments were in progress at fiscal year end. Burn data indicate that the incinerator will work well for combustible liquids. Improved data on incinerator performance will be generated upon completion of system changes and utilization of new sampling and analysis equipment. Mound Facility received advanced guidance from the Transuranic Waste Systems Office that this program will be cancelled in FY-1981 because of reductions in funding levels

EFFECT OF MELTER-FEED-MAKEUP ON VITRIFICATION PROCESS

International Nuclear Information System (INIS)

Kruger, A.A.; Hrma, P.R.; Schweiger, M.J.; Humrickhouse, C.J.; Moody, J.A.; Tate, R.M.; Tegrotenhuis, N.E.; Arrigoni, B.M.; Rodriguez, C.P.

2009-01-01

Increasing the rate of glass processing in the Hanford Tank Waste Treatment and Immobilization Plant (WTP) will allow shortening the life cycle of waste cleanup at the Hanford Site. While the WTP melters have approached the limit of increasing the rate of melting by enhancing the heat transfer rate from molten glass to the cold cap, a substantial improvement can still be achieved by accelerating the feed-to-glass conversion kinetics. This study investigates how the feed-to-glass conversion process responds to the feed makeup. By identifying the means of control of primary foam formation and silica grain dissolution, it provides data needed for a meaningful and economical design of large-scale experiments aimed at achieving faster melting

Summary of Waste Calcination at INTEC

Energy Technology Data Exchange (ETDEWEB)

O' Brien, Barry Henry; Newby, Bill Joe

2000-10-01

Fluidized-bed calcination at the Idaho Nuclear Technologies and Engineering Center (INTEC, formally called the Idaho Chemical Processing Plant) has been used to solidify acidic metal nitrate fuel reprocessing and incidental wastes wastes since 1961. A summary of waste calcination in full-scale and pilot plant calciners has been compiled for future reference. It contains feed compositions and operating conditions for all the processing campaigns for the original Waste Calcining Facility (WCF), the New Waste Calcining Facility (NWCF) started up in 1982, and numerous small scale pilot plant tests for various feed types. This summary provides a historical record of calcination at INTEC, and will be useful for evaluating calcinability of future wastes.

Nuclear waste solidification

Science.gov (United States)

Bjorklund, William J.

1977-01-01

High level liquid waste solidification is achieved on a continuous basis by atomizing the liquid waste and introducing the atomized liquid waste into a reaction chamber including a fluidized, heated inert bed to effect calcination of the atomized waste and removal of the calcined waste by overflow removal and by attrition and elutriation from the reaction chamber, and feeding additional inert bed particles to the fluidized bed to maintain the inert bed composition.

Nuclear waste solidification

International Nuclear Information System (INIS)

Bjorklund, W.J.

1977-01-01

High level liquid waste solidification is achieved on a continuous basis by atomizing the liquid waste and introducing the atomized liquid waste into a reaction chamber including a fluidized, heated inert bed to effect calcination of the atomized waste and removal of the calcined waste by overflow removal and by attrition and elutriation from the reaction chamber, and feeding additional inert bed particles to the fluidized bed to maintain the inert bed composition

Comparing the effects of feeding a grain- or a fish meal-based diet on water quality, waste production, and rainbow trout Oncorhynchus mykiss performance within low exchange water recirculating aquaculture systems

Science.gov (United States)

Feeding a fish meal-free grain-based diet (GB) was compared to feeding a fish meal-based diet (FM) relative to water quality criteria, waste production, water treatment process performance, and rainbow trout Oncorhynchus mykiss performance within six replicated water recirculating aquaculture system...

Preparation and evaporation of Hanford Waste treatment plant direct feed low activity waste effluent management facility simulant

Energy Technology Data Exchange (ETDEWEB)

Adamson, D. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Nash, C. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Howe, A. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); McCabe, D. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

2017-09-07

The Hanford Waste Treatment and Immobilization Plant (WTP) Low Activity Waste (LAW) vitrification facility will generate an aqueous condensate recycle stream (LAW Melter Off-Gas Condensate, LMOGC) from the off-gas system. The baseline plan for disposition of this stream during full WTP operations is to send it to the WTP Pretreatment Facility, where it will be blended with LAW, concentrated by evaporation, and recycled to the LAW vitrification facility. However, during the Direct Feed LAW (DFLAW) scenario, planned disposition of this stream involves concentrating the condensate in a new evaporator at the Effluent Management Facility (EMF) and returning it to the LAW melter. The LMOGC stream will contain components, e.g. halides and sulfates, that are volatile at melter temperatures, have limited solubility in glass waste forms, and present a material corrosion concern. Because this stream will recycle within WTP, these components are expected to accumulate in the LMOGC stream, exacerbating their impact on the number of LAW glass containers that must be produced. Diverting the stream reduces the halides and sulfates in the glass and is a key objective of this program. In order to determine the disposition path, it is key to experimentally determine the fate of contaminants. To do this, testing is needed to account for the buffering chemistry of the components, determine the achievable evaporation end point, identify insoluble solids that form, determine the formation and distribution of key regulatoryimpacting constituents, and generate an aqueous stream that can be used in testing of the subsequent immobilization step. This overall program examines the potential treatment and immobilization of the LMOGC stream to enable alternative disposal. The objective of this task was to (1) prepare a simulant of the LAW Melter Off-gas Condensate expected during DFLAW operations, (2) demonstrate evaporation in order to predict the final composition of the effluents from the EMF

Effects of feeding polyphenol-rich winery wastes on digestibility, nitrogen utilization, ruminal fermentation, antioxidant status and oxidative stress in wethers.

Science.gov (United States)

Ishida, Kyohei; Kishi, Yosuke; Oishi, Kazato; Hirooka, Hiroyuki; Kumagai, Hajime

2015-03-01

Four wethers were used in a 4 × 4 Latin square design experiment to evaluate the availability of two types of winery wastes, winery sediment and grape pomace, as ruminant feeds possessing antioxidant activities. Each wether was assigned to one of the following four treatments: (i) 75 g/kg winery sediment (WS) on a dry matter (DM) basis; (ii) 166 g/kg DM winery grape pomace (WP); (iii) control diet (CD; 17 g/kg DM soybean meal);and (iv) only tall fescue hay (TFH; no additive). Winery sediment and grape pomace had high levels of polyphenols and of radical scavenging activities. Feeding with winery sediment and grape pomace did not negatively affect the intake, but it depressed crude protein (CP) digestibility compared with CD (P = 0.052 and P winery wastes decreased ruminal ammonia production (P = 0.089 and P winery sediment and grape pomace decreased urinary 8-hydroxy-2'-deoxyguanosine (8-OHdG; an index of oxidative damages) excretion per day (P winery sediment and grape pomace could alter nitrogen metabolism and/or act as new antioxidants for ruminants. © 2014 Japanese Society of Animal Science.

Effect of Feed Melting, Temperature History and Minor Component Addition on Spinel Crystallization in High-Level Waste Glass

International Nuclear Information System (INIS)

Izak, Pavel; Hrma, Pavel R.; Arey, Bruce W.; Plaisted, Trevor J.

2001-01-01

This study was undertaken to help design mathematical models for high-level waste (HLW) glass melter that simulate spinel behavior in molten glass. Spinel, (Fe,Ni,Mn) (Fe,Cr)2O4, is the primary solid phase that precipitates from HLW glasses containing Fe and Ni in sufficient concentrations. Spinel crystallization affects the anticipated cost and risk of HLW vitrification. To study melting reactions, we used simulated HLW feed, prepared with co-precipitated Fe, Ni, Cr, and Mn hydroxides. Feed samples were heated up at a temperature-increase rate (4C/min) close to that which the feed experiences in the HLW glass melter. The decomposition, melting, and dissolution of feed components (such as nitrates, carbonates, and silica) and the formation of intermediate crystalline phases (spinel, sodalite (Na8(AlSiO4)6(NO2)2), and Zr-containing minerals) were characterized using evolved gas analysis, volume-expansion measurement, optical microscope, scanning electron microscope, thermogravimetric analysis, differential scanning calorimetry, and X-ray diffraction. Nitrates and quartz, the major feed components, converted to a glass-forming melt by 880C. A chromium-free spinel formed in the nitrate melt starting from 520C and Sodalite, a transient product of corundum dissolution, appeared above 600C and eventually dissolved in glass. To investigate the effects of temperature history and minor components (Ru,Ag, and Cu) on the dissolution and growth of spinel crystals, samples were heated up to temperatures above liquidus temperature (TL), then subjected to different temperature histories, and analyzed. The results show that spinel mass fraction, crystals composition, and crystal size depend on the chemical and physical makeup of the feed and temperature history

Feed Variability and Bulk Vitrification Glass Performance Assessment

International Nuclear Information System (INIS)

Mahoney, Lenna A.; Vienna, John D.

2005-01-01

The supplemental treatment (ST) bulk vitrification process will obtain its feed, consisting of low-activity waste (LAW), from more than one source. One purpose of this letter report is to describe the compositional variability of the feed to ST. The other is to support the M-62-08 decision by providing a preliminary assessment of the effectiveness of bulk vitrification (BV), the process that has been selected to perform supplemental treatment, in handling the ST feed envelope. Roughly nine-tenths of the ST LAW feed will come from the Waste Treatment Plant (WTP) pretreatment. This processed waste is expected to combine (1) a portion of the same LAW feed sent to the WTP melters and (2) a dilute stream that is the product of the condensate from the submerged-bed scrubber (SBS) and the drainage from the electrostatic precipitator (WESP), both of which are part of the LAW off-gas system. The manner in which the off-gas-product stream is concentrated to reduce its volume, and the way in which the excess LAW and off-gas product streams are combined, are part of the interface between WTP and ST and have not been determined. This letter report considers only one possible arrangement, in which half of the total LAW is added to the off-gas product stream, giving an estimated ST feed stream from WTP. (Total LAW equals that portion of LAW sent to the WTP LAW vitrification plant (WTP LAW) plus the LAW not currently treatable in the LAW vitrification plant due to capacity limitations (excess))

Antimicrobial residues in animal waste and water resources proximal to large-scale swine and poultry feeding operations

Science.gov (United States)

Campagnolo, E.R.; Johnson, K.R.; Karpati, A.; Rubin, C.S.; Kolpin, D.W.; Meyer, M.T.; Esteban, J. Emilio; Currier, R.W.; Smith, K.; Thu, K.M.; McGeehin, M.

2002-01-01

Expansion and intensification of large-scale animal feeding operations (AFOs) in the United States has resulted in concern about environmental contamination and its potential public health impacts. The objective of this investigation was to obtain background data on a broad profile of antimicrobial residues in animal wastes and surface water and groundwater proximal to large-scale swine and poultry operations. The samples were measured for antimicrobial compounds using both radioimmunoassay and liquid chromatography/electrospray ionization-mass spectrometry (LC/ESI-MS) techniques. Multiple classes of antimicrobial compounds (commonly at concentrations of >100 μg/l) were detected in swine waste storage lagoons. In addition, multiple classes of antimicrobial compounds were detected in surface and groundwater samples collected proximal to the swine and poultry farms. This information indicates that animal waste used as fertilizer for crops may serve as a source of antimicrobial residues for the environment. Further research is required to determine if the levels of antimicrobials detected in this study are of consequence to human and/or environmental ecosystems. A comparison of the radioimmunoassay and LC/ESI-MS analytical methods documented that radioimmunoassay techniques were only appropriate for measuring residues in animal waste samples likely to contain high levels of antimicrobials. More sensitive LC/ESI-MS techniques are required in environmental samples, where low levels of antimicrobial residues are more likely.

Antimicrobial residues in animal waste and water resources proximal to large-scale swine and poultry feeding operations.

Science.gov (United States)

Campagnolo, Enzo R; Johnson, Kammy R; Karpati, Adam; Rubin, Carol S; Kolpin, Dana W; Meyer, Michael T; Esteban, J Emilio; Currier, Russell W; Smith, Kathleen; Thu, Kendall M; McGeehin, Michael

2002-11-01

Expansion and intensification of large-scale animal feeding operations (AFOs) in the United States has resulted in concern about environmental contamination and its potential public health impacts. The objective of this investigation was to obtain background data on a broad profile of antimicrobial residues in animal wastes and surface water and groundwater proximal to large-scale swine and poultry operations. The samples were measured for antimicrobial compounds using both radioimmunoassay and liquid chromatography/electrospray ionization-mass spectrometry (LC/ESI-MS) techniques. Multiple classes of antimicrobial compounds (commonly at concentrations of > 100 microg/l) were detected in swine waste storage lagoons. In addition, multiple classes of antimicrobial compounds were detected in surface and groundwater samples collected proximal to the swine and poultry farms. This information indicates that animal waste used as fertilizer for crops may serve as a source of antimicrobial residues for the environment. Further research is required to determine if the levels of antimicrobials detected in this study are of consequence to human and/or environmental ecosystems. A comparison of the radioimmunoassay and LC/ESI-MS analytical methods documented that radioimmunoassay techniques were only appropriate for measuring residues in animal waste samples likely to contain high levels of antimicrobials. More sensitive LC/ESI-MS techniques are required in environmental samples, where low levels of antimicrobial residues are more likely.

RFID technology for hazardous waste management and tracking.

Science.gov (United States)

Namen, Anderson Amendoeira; Brasil, Felipe da Costa; Abrunhosa, Jorge José Gouveia; Abrunhosa, Glaucia Gomes Silva; Tarré, Ricardo Martinez; Marques, Flávio José Garcia

2014-09-01

The illegal dumping of hazardous waste is one of the most concerning occurrences related to illegal waste activities. The waste management process is quite vulnerable, especially when it comes to assuring the right destination for the delivery of the hazardous waste. The purpose of this paper is to present a new system design and prototype for applying the RFID technology so as to guarantee the correct destination for the hazardous waste delivery. The aim of this innovative approach, compared with other studies that employ the same technology to the waste disposal process, is to focus on the certification that the hazardous waste will be delivered to the right destination site and that no inappropriate disposal will occur in the transportation stage. These studies were carried out based on data collected during visits to two hazardous waste producer companies in Brazil, where the material transportation and delivery to a company in charge of the waste disposal were closely monitored. © The Author(s) 2014.

Towards zero solid waste: utilising tannery waste as a protein source for poultry feed

OpenAIRE

Paul, Hiralal; Antunes, A Paula M; Covington, Anthony D; Evans, Paul; Phillips, Paul S

2013-01-01

Zero waste is now a strongly emerging issue for sustainable industrial development where minimisation and utilisation of waste are a priority in the leather industry. In a tannery hides and skins converted in to leather through various processes. Approximately 20% (w/w) of the chrome containing tannery solid waste (TSW) is generated from one tonne of raw hides and skins. However, tannery solid waste may also be a resource if it is managed expertly as we move towards zero waste.\\ud This resear...

40 CFR 61.155 - Standard for operations that convert asbestos-containing waste material into nonasbestos...

Science.gov (United States)

2010-07-01

... to the information requirements of § 61.07(b)(3), a (i) Description of waste feed handling and...) Disposed of as asbestos-containing waste material according to § 61.150, or (ii) Recycled as waste feed... waste feed to the process. (2) Collect and analyze monthly composite samples (one 200-gram (7-ounce...

Evaporation Of Hanford Waste Treatment Plant Direct Feed Low Activity Waste Effluent Management Facility Core Simulant

Energy Technology Data Exchange (ETDEWEB)

Adamson, D. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Nash, C. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Mcclane, D. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); McCabe, D. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

2016-09-01

The Hanford Waste Treatment and Immobilization Plant (WTP) Low Activity Waste (LAW) vitrification facility will generate an aqueous condensate recycle stream (LAW Melter Off-Gas Condensate, LMOGC) from the off-gas system. The baseline plan for disposition of this stream during full WTP operations is to send it to the WTP Pretreatment Facility, where it will be blended with LAW, concentrated by evaporation, and recycled to the LAW vitrification facility. However, during the Direct Feed LAW (DFLAW) scenario, planned disposition of this stream is to evaporate it in a new evaporator, in the Effluent Management Facility (EMF), and then return it to the LAW melter. It is important to understand the composition of the effluents from the melter and new evaporator, so that the disposition of these streams can be accurately planned and accommodated. Furthermore, alternate disposition of the LMOGC stream would eliminate recycling of problematic components, and would reduce the need for closely integrated operation of the LAW melter and the Pretreatment Facilities. Long-term implementation of this option after WTP start-up would decrease the LAW vitrification mission duration and quantity of glass waste, amongst the other operational complexities such a recycle stream presents. In order to accurately plan for the disposition path, it is key to experimentally determine the fate of contaminants. To do this, testing is needed to accurately account for the buffering chemistry of the components, determine the achievable evaporation end point, identify insoluble solids that form, and determine the distribution of key regulatory-impacting constituents. The LAW Melter Off-Gas Condensate stream will contain components that are volatile at melter temperatures, have limited solubility in the glass waste form, and represent a materials corrosion concern, such as halides and sulfate. Because this stream will recycle within WTP, these components will accumulate in the Melter Condensate

Changes in complementary feeding practices and nutrition status in ...

African Journals Online (AJOL)

Objectives: Evaluate changes in underweight and wasting, feeding patterns, water use, sanitation, immunisation, disease episodes, deworming and vitamin A supplementation in children aged 6-23 months in returnee villages benefiting from a community-based supplementary feeding programme in northern Uganda.

Apparatus of vaporizing and condensing liquid radioactive wastes and its operation method

International Nuclear Information System (INIS)

Irie, Hiromitsu; Tajima, Fumio.

1975-01-01

Object: To prevent corrosion of material for a vapor-condenser and a vapor heater and to prevent radioactive contamination of heated vapor. Structure: Liquid waste is fed from a liquid feeding tank to a vapor-condenser to vaporize and condense the waste. Uncondensed liquid waste, which is not in a level of a given density, is temporally stored in a batch tank through a switching valve and a pipe. Prior to successive feeding from the liquid feeding tank, the uncondensed liquid waste within the batch tank is returned by a return pump to the condenser, after which a new liquid is fed from the liquid feeding tank for re-vaporization and condensation in the vapor-condenser. Then, similar operation is repeated until the uncondensed liquid waste assumes a given density, and when the uncondensed liquid waste reaches a given density, the condensed liquid waste is discharged into the storage tank through the switching valve. (Ohara, T.)

Feed Additives Production Out of Dairy Industry Waste

Science.gov (United States)

Ulrikh, EV

2017-05-01

Application of macro- and microelements in animal feed is the most effective in the case of their industrial brining in mixed feeds, feed mixes, and protein-vitamin supplements in the form of various complex salts. Application of the product contributes to the body’s needs of broiler chickens in vitamins and minerals, normalization of metabolism, and ensures a high rate of growth and development. The composition of the premix can be adjusted depending on the actual proportion of biologically active substances in the feed used by a consumer. It is possible to include in the premix other biologically active substances. Assessing the slaughter qualities of experimental pigs, it was found (Table. 2) that the pigs of group II has a tendency toward greater weight of hot carcass (4.5 kg), of slaughter yelts (by 3.83%) and toward a smaller thickness of fat over the spinous processes of the 6-7th thoracic vertebrae (1.67 mm). The performed investigations have established that there is no significant difference between groups I and II in the content of certain amino acids, however, group I shows poorer results in the content of valine, isoleucine, leucine and lysine by 0.16 g / 100 g of protein (P> 0.999) 0.2 (P> 0.90), 0.46 (P> 0.999) and 0.39 (P> 0.999) g / 100 g protein respectively.

An educational intervention on promotion of breast feeding.

Science.gov (United States)

Neyzi, O; Olgun, P; Kutluay, T; Uzel, N; Saner, G; Gökçay, G; Taşdelen, E; Akar, U

1991-07-01

This study was designed to search for an effective method to promote exclusive breast feeding among Turkish city women delivering in hospitals. Four hundred and forty-two primiparae with uncomplicated deliveries and with healthy infants with birthweights of greater than 2500 g were exposed to a group educational session on breast feeding after birth, followed by one repeat session at home. Four hundred and ninety-nine women served as controls. All homes were visited monthly for 6 months by independent observers and data relevant to the feeding of the infants were collected. Weight measurements of 176 infants were taken at age 4 months. The study and control mothers were similar in sociodemographic characteristics which reflected a low socio-economic/educational background but relatively good housing conditions. Although significant differences in frequency of exclusive breast feeding were found between the study and control groups, the impact of the intervention was much lower than our expectations and short-lived. Type of feeding was not related to sex or birthweight of the infant, nor to maternal variables. Weight at age 4 months was within normal limits and similar in the study and control groups. It was concluded that lack of up-to-date information on infant feeding was the main obstacle to breast feeding in urban groups in Turkey, and that the impact of an educational intervention limited to the first week after delivery was lost within the first 2 months.

Maternal factors in newborns breast feeding jaundice: a case control study

Directory of Open Access Journals (Sweden)

Alizadeh Taheri P

2013-03-01

Full Text Available Background: Neonatal jaundice, especially breast feeding jaundice is one of the most common causes of neonatal readmission during the first month of life. Breast feeding jaundice may be due to decreased milk intake with dehydration and/or reduced caloric intake.  The aim of this Study was to determine maternal risk factors of breast feeding jaundice in order to prevent it than before.Methods: This case- control study was performed at Bahrami University Hospital, Tehran, Iran and involved 75 term exclusively breast fed newborns admitted for hyperbilirubinemia, with a weight loss greater than 7%, with one positive lab data as: serum Na≥ 150meq/lit, urine specific gravity> 1012, serum urea≥ 40mgr/dl, without assigned cause for hyperbilirubinemia. They were compared with 75 matched controls with weight loss less than 7%, without dehydration and a known cause of hyperbilirubinemia.Results: In comparison with control group, in neonates with breast feeding jaundice, inappropriate feeding practice (P<0.033, delayed onset of lactation (P<0.0001, inverted nipple (P<0.001 were significantly higher. In our study, there was no significant difference between two groups in education level of mother, learning breast feeding practice before and after delivery, method of delivery (cesarean or vaginal delivery, primiparity or multiparity and use of supplements (water or glucose water.Conclusion: This study shows need for special attention and follows up of mothers and neonates at risk for breast feeding jaundice, especially those with inverted nipples or undergraduate for successful breast feeding. On the other hand this study shows encouraging mothers for early lactation especially in the first hour of life decreases the risk for this kind of jaundice.

Technological foundations of processing tomato pomace in feed additives

Directory of Open Access Journals (Sweden)

B. Yegorov

2015-05-01

Full Text Available Introduction. Search for new types of alternative raw material for the efficient development of poultry industry and problem of waste disposal of canning industry made it necessary to develop a method of processing tomato pomace in feed additives. Materials and methods. Sampling, preparation and testing were carried out by general and specific organ oleptic and physical-technological methods of assessment and analysis of the properties of raw materials and finished products. Results. Incorporation of tomato pomace in the feed additive reduces the cost of raw materials and expenses associated with moistening of the mixture before extrusion and incorporation of chalk feed will solve the problem of calcium imbalance of laying hens. It was found that extrusion process has improved the physical properties of feed additive and showed the possibility of its use as a feed component: moisture content decreased by 34.5 %, the angle of repose increased by 11.4 %, flowability decreased by 39.7 % and bulk density decreased by 32.3 %. Conclusions. The resulting feed additive will solve the problem of diversification of raw materials, waste, calcium imbalance of laying hens and reduce expenses on compound animal feedstuff production.

HANFORD SITE RIVER PROTECTION PROJECT (RPP) TRANSURANIC (TRU) TANK WASTE IDENTIFICATION and PLANNING FOR REVRIEVAL TREATMENT and EVENTUAL DISPOSAL AT WIPP

International Nuclear Information System (INIS)

KRISTOFZSKI, J.G.; TEDESCHI, R.; JOHNSON, M.E.; JENNINGS, M

2006-01-01

The CH2M HILL Manford Group, Inc. (CHG) conducts business to achieve the goals of the Office of River Protection (ORP) at Hanford. As an employee owned company, CHG employees have a strong motivation to develop innovative solutions to enhance project and company performance while ensuring protection of human health and the environment. CHG is responsible to manage and perform work required to safely store, enhance readiness for waste feed delivery, and prepare for treated waste receipts for the approximately 53 million gallons of legacy mixed radioactive waste currently at the Hanford Site tank farms. Safety and environmental awareness is integrated into all activities and work is accomplished in a manner that achieves high levels of quality while protecting the environment and the safety and health of workers and the public. This paper focuses on the innovative strategy to identify, retrieve, treat, and dispose of Hanford Transuranic (TRU) tank waste at the Waste Isolation Pilot Plant (WIPP)

Self mixing of fly larvae during feeding

Science.gov (United States)

Shishkov, Olga; Johnson, Christopher; Hu, David

How do we sustainably feed a growing world population? One solution of increasing interest is the use of black solider fly larvae, pea-sized grubs envisioned to transform hundreds of tons of food waste into a sustainable protein source. Although startups across the world are raising these larvae, a physical understanding of how they should be raised and fed remains missing. In this study, we present experiments measuring their feeding rate as a function of number of larvae. We show that larger groups of larvae have greater mixing which entrains hungry larvae around the food, increasing feeding rate. Feeding of larvae thus differs from feeding of cattle or other livestock which exhibit less self-mixing.

Low-Activity Waste Feed Data Quality Objectives

Energy Technology Data Exchange (ETDEWEB)

MJ Truex; KD Wiemers

1998-12-11

This document describes characterization requirements for the Tank Waste Remediation System (TWRS) Waste Disposal Program's privatization efforts in support of low-activity waste (LAW) treatment and immobilization, This revised Data Quality Objective (DQO) replaces earlier documents (PNNL 1997; DOE-W 1998zq Wiemers 1996). Revision O of this DQO was completed to meet Tri-Party Agreement (TPA) target milestone M-60-14-TO1. Revision 1 updates the data requirements based on the contract issued `August 1998 (DOE-RL 1998b). In addition, sections of Revision O pertaining to "environmental planning" were not acceptable to the Washington State Department of Ecology (Ecology) and have been removed. Regulatory compliance for TWRS Privatization is being addressed in a separate DQO (Wiemers et al. 1998). The Project Hanford Management Contract (PHMC) Contractors and the private contractor may elect to complete issue-specific DQOS to accommodate their individual work scope.

Supported liquid membrane based removal of lead(II) and cadmium(II) from mixed feed: Conversion to solid waste by precipitation

Energy Technology Data Exchange (ETDEWEB)

Bhatluri, Kamal Kumar; Manna, Mriganka Sekhar; Ghoshal, Aloke Kumar; Saha, Prabirkumar, E-mail: p.saha@iitg.ac.in

2015-12-15

Highlights: • Simultaneous removal of two heavy metals lead and cadmium. • Conversion of liquid waste to solid precipitation. • Precipitation facilitates the metals transportation through LM. • Solidification of liquid waste minimizes the final removal of waste. - Abstract: Simultaneous removal of two heavy metals, lead(II) and cadmium(II), from mixed feed using supported liquid membrane (SLM) based technique is investigated in this work. The carrier-solvent combination of “sodium salt of Di-2-ethylhexylphosphoric acid (D2EHPA) (4% w/w) in environmentally benign coconut oil” was immobilized into the pores of solid polymeric polyvinylidene fluoride (PVDF) support. Sodium carbonate (Na{sub 2}CO{sub 3}) was used as the stripping agent. Carbonate salts of lead(II) and cadmium(II) were formed in the stripping side interface and they were insoluble in water leading to precipitation inside the stripping solution. The transportation of solute is positively affected due to the precipitation. Lead(II) removal was found to be preferential due to its favorable electronic configuration. The conversion of the liquid waste to the solid one was added advantage for the final removal of hazardous heavy metals.

Behavioral Change Strategies for Improving Complementary Feeding and Breastfeeding.

Science.gov (United States)

Osendarp, Saskia J M; Roche, Marion L

2016-01-01

Improving infant and young child feeding (IYCF) practices, including breastfeeding and complementary feeding, has been identified as one of the most effective interventions to improve child survival, stunting and wasting. Evidence from randomized controlled trials suggests that effective promotion of breastfeeding and complementary feeding, with or without food provision, has the potential to improve IYCF practices and child nutrition. However, in many countries, breastfeeding practices and complementary feeding practices are still far from optimal. The lack of implementation of available, effective, affordable interventions in scale-up programs is in part attributed to a lack of innovative, creative and effective behavioral change strategies that enable and encourage caregivers. Successful behavioral change strategies should be based on a rigorous situational analysis and formative research, and the findings and insights of formative research should be used to further design interventions that address the identified barriers and enablers, to select delivery channels, and to formulate appropriate and effective messages. In addition, successful behavioral change interventions should a priori define and investigate the program impact pathway to target behavioral change and should assess intermediary behavioral changes and indicators to learn why the expected outcome was achieved or not achieved by testing the program theory. The design of behavioral change communication must be flexible and responsive to shifts in societies and contexts. Performance of adequate IYCF also requires investments to generate community demand through social mobilization, relevant media and existing support systems. Applying these principles has been shown to be effective in improving IYCF practices in Vietnam, Bangladesh and Ethiopia and is recommended to be adopted by other programs and countries in order to accelerate progress in improving child nutrition. © 2016 S. Karger AG, Basel.

Volume reduction by crystallization of low-level radioactive wastes

International Nuclear Information System (INIS)

Grant, D.C.; Murray, A.P.

1982-01-01

Low-level radioactive wastes containing boric acid, borax, or sodium sulfate, with radioactive contaminants, are generated during the operation of nuclear power plants. These wastes require disposal, and as such, it is economically and environmentally desirable to reduce their volume. Crystallization was examined in the laboratory as a means of accomplishing this. The crystallizer was operated in both of two modes: evaporative cooling and total evaporation. A 12 wt% boric acid waste feed was concentrated to a 40 to 45 wt% slurry in both modes of operation. Using pure boric acid, a slurry containing over 60 wt% was obtained. An 18.5 wt% borax waste feed was concentrated to 50 wt% in the total evaporative mode and 70 wt% in the evaporatively cooled mode. A 22 wt% sodium sulfate feed was concentrated to a 78 wt% slurry in the total evaporative mode. For all of the feeds, this represents a 4- to 5-fold volume reduction by the crystallizer

Comparative Energy Values Of Sorghum Distillers Waste, Maize ...

African Journals Online (AJOL)

A balance trial aimed at determining the energy values of Sorghum Distiller's Wastes (SDW), Maize cob (MC) and Shea butter Waste (SBW) for barrows was conducted using a 4 x 4 Latin square cross- over experimental design. While feed intake was influenced (P < 0.05) by the test feed ingredients, the weight gained was ...

Waste Feed Delivery Purex Process Connector Design Pressure

International Nuclear Information System (INIS)

BRACKENBURY, P.J.

2000-01-01

The pressure retaining capability of the PUREX process connector is documented. A context is provided for the connector's current use within existing Projects. Previous testing and structural analyses campaigns are outlined. The deficient condition of the current inventory of connectors and assembly wrenches is highlighted. A brief history of the connector is provided. A bibliography of pertinent references is included

Waste Management Technical Manual

Energy Technology Data Exchange (ETDEWEB)

Buckingham, J.S. [ed.

1967-08-31

This Manual has been prepared to provide a documented compendium of the technical bases and general physical features of Isochem Incorporated`s Waste Management Program. The manual is intended to be used as a means of training and as a reference handbook for use by personnel responsible for executing the Waste Management Program. The material in this manual was assembled by members of Isochem`s Chemical Processing Division, Battelle Northwest Laboratory, and Hanford Engineering Services between September 1965 and March 1967. The manual is divided into the following parts: Introduction, contains a summary of the overall Waste Management Program. It is written to provide the reader with a synoptic view and as an aid in understanding the subsequent parts; Feed Material, contains detailed discussion of the type and sources of feed material used in the Waste Management Program, including a chapter on nuclear reactions and the formation of fission products; Waste Fractionization Plant Processing, contains detailed discussions of the processes used in the Waste Fractionization Plant with supporting data and documentation of the technology employed; Waste Fractionization Plant Product and Waste Effluent Handling, contains detailed discussions of the methods of handling the product and waste material generated by the Waste Fractionization Plant; Plant and Equipment, describes the layout of the Waste Management facilities, arrangement of equipment, and individual equipment pieces; Process Control, describes the instruments and analytical methods used for process control; and Safety describes process hazards and the methods used to safeguard against them.

The Continued Need for Modeling and Scaled Testing to Advance the Hanford Tank Waste Mission

Energy Technology Data Exchange (ETDEWEB)

Peurrung, Loni M.; Fort, James A.; Rector, David R.

2013-09-03

Hanford tank wastes are chemically complex slurries of liquids and solids that can exhibit changes in rheological behavior during retrieval and processing. The Hanford Waste Treatment and Immobilization Plant (WTP) recently abandoned its planned approach to use computational fluid dynamics (CFD) supported by testing at less than full scale to verify the design of vessels that process these wastes within the plant. The commercial CFD tool selected was deemed too difficult to validate to the degree necessary for use in the design of a nuclear facility. Alternative, but somewhat immature, CFD tools are available that can simulate multiphase flow of non-Newtonian fluids. Yet both CFD and scaled testing can play an important role in advancing the Hanford tank waste mission—in supporting the new verification approach, which is to conduct testing in actual plant vessels; in supporting waste feed delivery, where scaled testing is ongoing; as a fallback approach to design verification if the Full Scale Vessel Testing Program is deemed too costly and time-consuming; to troubleshoot problems during commissioning and operation of the plant; and to evaluate the effects of any proposed changes in operating conditions in the future to optimize plant performance.

Vitrification of SRP waste by a slurry-fed ceramic melter

International Nuclear Information System (INIS)

Wicks, G.G.

1980-01-01

Savannah River Plant (SRP) high-level waste (HLW) can be vitrified by feeding a slurry, instead of a calcine, to a joule-heated ceramic melter. Potential advantages of slurry feeding include (1) use of simpler equipment, (2) elimination of handling easily dispersed radioactive powder, (3) simpler process control, (4) effective mixing, (5) reduced off-gas volume, and (6) cost savings. Assessment of advantages and disadvantages of slurry feeding along with experimental studies indicate that slurry feeding is a promising way of vitrifying waste

Volatility and entrainment of feed components and product glass characteristics during pilot-scale vitrification of simulated Hanford site low-level waste

International Nuclear Information System (INIS)

Shade, J.W.

1996-01-01

Commercially available melter technologies were tested for application to vitrification of Hanford site low-level waste (LLW). Testing was conducted at vendor facilities using a non-radioactive LLW simulant. Technologies tested included four Joule-heated melter types, a carbon electrode melter, a cyclone combustion melter, and a plasma torch-fired melter. A variety of samples were collected during the vendor tests and analyzed to provide data to support evaluation of the technologies. This paper describes the evaluation of melter feed component volatility and entrainment losses and product glass samples produced during the vendor tests. All vendors produced glasses that met minimum leach criteria established for the test glass formulations, although in many cases the waste oxide loading was less than intended. Entrainment was much lower in Joule-heated systems than in the combustion or plasma torch-fired systems. Volatility of alkali metals, halogens, B, Mo, and P were severe for non-Joule-heated systems. While losses of sulfur were significant for all systems, the volatility of other components was greatly reduced for some configurations of Joule-heated melters. Data on approaches to reduce NO x generation, resulting from high nitrate and nitrite content in the double-shell slurry feed, are also presented

Outcomes of vaginal delivery and cesarean in Mashhad Ghaem University Hospital

Directory of Open Access Journals (Sweden)

Hassan Boskabadi

2014-03-01

Conclusion: The results of this study showed in comparison with cesarean delivery, normal vaginal delivery provides better outcomes in terms of breast problems, breast feeding status, duration of labor and duration of maternal hospitalization for both mother and infant. So, adopting careful instructions in management and administration of deliveries will help the prevalence of making decisions for normal vaginal delivery and the recovery of delivery outcomes.

Melter Feed Reactions at T ≤ 700°C for Nuclear Waste Vitrification

Energy Technology Data Exchange (ETDEWEB)

Xu, Kai [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Hrma, Pavel R. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Rice, Jarrett A. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Riley, Brian J. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Schweiger, Michael J. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Crum, Jarrod V. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

2015-07-23

Batch reactions and phase transitions in a nuclear waste feed heated at 5 K min-1 up to 600°C were investigated by optical microscopy, scanning electron microscopy with energy dispersive X-ray spectrometer, and X-ray diffraction. Quenched samples were leached in deionized water at room temperature and 80°C to extract soluble salts and early glass-forming melt, respectively. To determine the content and composition of leachable phases, the leachates were analyzed by the inductively-coupled plasma spectroscopy. By ~400°C, gibbsite and borax lost water and converted to amorphous and intermediate crystalline phases. Between 400°C and 600°C, the sodium borate early glass-forming melt reacted with amorphous aluminum oxide and calcium oxide to form intermediate products containing Al and Ca. At ~600°C, half Na and B converted to the early glass-forming melt, and quartz began to dissolve in the melt.

Compatibility Grab Sampling and Analysis Plan for FY 2000

International Nuclear Information System (INIS)

SASAKI, L.M.

1999-01-01

This sampling and analysis plan (SAP) identifies characterization objectives pertaining to sample collection, laboratory analytical evaluation, and reporting requirements for grab samples obtained to address waste compatibility. It is written in accordance with requirements identified in Data Quality Objectives for Tank Farms Waste Compatibility Program (Mulkey et al. 1999) and Tank Farm Waste Transfer Compatibility Program (Fowler 1999). In addition to analyses to support Compatibility, the Waste Feed Delivery program has requested that tank samples obtained for Compatibility also be analyzed to confirm the high-level waste and/or low-activity waste envelope(s) for the tank waste (Baldwin 1999). The analytical requirements to confirm waste envelopes are identified in Data Quality Objectives for TWRS Privatization Phase I: Confirm Tank T is an Appropriate Feed Source for Low-Activity Waste Feed Batch X (Nguyen 1999a) and Data Quality Objectives for RPP Privatization Phase I: Confirm Tank T is an Appropriate Feed Source for High-Level Waste Feed Batch X (Nguyen 1999b)

FEED SYSTEM INNOVATION FOR GASIFICATION OF LOCALLY ECONOMICAL ALTERNATIVE FUELS (FIGLEAF)

Energy Technology Data Exchange (ETDEWEB)

Michael L. Swanson; Mark A. Musich; Darren D. Schmidt; Joseph K. Schultz

2003-02-01

The Feed System Innovation for Gasification of Locally Economical Alternative Fuels (FIGLEAF) project was conducted by the Energy & Environmental Research Center and Gasification Engineering Corporation of Houston, Texas (a subsidiary of Global Energy Inc., Cincinnati, Ohio), with 80% cofunding from the U.S. Department of Energy (DOE). The goal of the project was to identify and evaluate low-value fuels that could serve as alternative feedstocks and to develop a feed system to facilitate their use in integrated gasification combined-cycle and gasification coproduction facilities. The long-term goal, to be accomplished in a subsequent project, is to install a feed system for the selected fuel(s) at Global Energy's commercial-scale 262-MW Wabash River Coal Gasification Facility in West Terre Haute, Indiana. The feasibility study undertaken for the project consisted of identifying and evaluating the economic feasibility of potential fuel sources, developing a feed system design capable of providing a fuel at 400 psig to the second stage of the E-Gas (Destec) gasifier to be cogasified with coal, performing bench- and pilot-scale testing to verify concepts and clarify decision-based options, reviewing information on high-pressure feed system designs, and determining the economics of cofeeding alternative feedstocks with the conceptual feed system design. A preliminary assessment of feedstock availability within Indiana and Illinois was conducted. Feedstocks evaluated included those with potential tipping fees to offset processing cost: sewage sludge, municipal solid waste, used railroad ties, urban wood waste (UWW), and used tires/tire-derived fuel. Agricultural residues and dedicated energy crop fuels were not considered since they would have a net positive cost to the plant. Based on the feedstock assessment, sewage sludge was selected as the primary feedstock for consideration at the Wabash River Plant. Because of the limited waste heat available for drying and

Investigation of Rheological Impacts on the Defense Waste Processing Facility's Sludge Slurry Feed as Insoluble Solids and Wash Endpoints are Adjusted

International Nuclear Information System (INIS)

Fellinger, T. L.; Howard, S.J.; Lee, M.C.; Galloway, R.H.

2006-01-01

The Savannah River Site (SRS) is currently pursuing an aggressive program to empty its High Level Waste (HLW) tanks and immobilize its radioactive waste into a durable borosilicate glass in the Defense Waste Processing Facility (DWPF). To create a batch of feed for the DWPF, several tanks of radioactive sludge slurry are combined into one of the million gallon (i.e. 3.79 E06 liters) feed tanks for DWPF. Once these sludge slurries are combined, the soluble sodium and weight percent total solids are adjusted by a 'washing' process. The 'washing' process involves diluting the soluble sodium of the sludge slurry with inhibited water (0.015 M NaOH and 0.015 M NaNO 2 ) and allowing the sludge slurry to settle into two layers. The two layers in the tank consist of a clear supernate on top and a layer of settled sludge solids on the bottom. The clear supernate layer is then decanted to another hold tank. This 'washing' process is repeated until the desired wash endpoint (i.e. sodium concentration in the supernate) and weight percent total solids are achieved. A final washed batch of feed consists of approximately 500,000 gallons (i.e. 1.89 E06 liters). DWPF has already processed three batches of feed and is currently processing a fourth. Prior to processing a batch of feed in the DWPF, it must be well characterized. Samples of the prepared feed batch are sent to the Savannah River National Laboratory (SRNL) for this characterization. As a part of the SRNL characterization for the fourth batch, rheology measurements were performed. Measurements were performed at different weight percent insoluble solids loadings to mimic potential facility processing scenarios (i.e. mixing/pumping of concentrated sludge slurry). In order to determine the influence of the soluble Na on the rheological properties of the sample, the supernate of the 'as received' sample was adjusted from 1 M soluble Na to 0.5 M soluble Na by using a lab scale version of the 'washing' process. Rheology

Anaerobic co-digestion of the organic fraction of municipal solid waste with FOG waste from a sewage treatment plant: Recovering a wasted methane potential and enhancing the biogas yield

International Nuclear Information System (INIS)

Martin-Gonzalez, L.; Colturato, L.F.; Font, X.; Vicent, T.

2010-01-01

Anaerobic digestion is applied widely to treat the source collected organic fraction of municipal solid wastes (SC-OFMSW). Lipid-rich wastes are a valuable substrate for anaerobic digestion due to their high theoretical methane potential. Nevertheless, although fat, oil and grease waste from sewage treatment plants (STP-FOGW) are commonly disposed of in landfill, European legislation is aimed at encouraging more effective forms of treatment. Co-digestion of the above wastes may enhance valorisation of STP-FOGW and lead to a higher biogas yield throughout the anaerobic digestion process. In the present study, STP-FOGW was evaluated as a co-substrate in wet anaerobic digestion of SC-OFMSW under mesophilic conditions (37 o C). Batch experiments carried out at different co-digestion ratios showed an improvement in methane production related to STP-FOGW addition. A 1:7 (VS/VS) STP-FOGW:SC-OFMSW feed ratio was selected for use in performing further lab-scale studies in a 5 L continuous reactor. Biogas yield increased from 0.38 ± 0.02 L g VS feed -1 to 0.55 ± 0.05 L g VS feed -1 as a result of adding STP-FOGW to reactor feed. Both VS reduction values and biogas methane content were maintained and inhibition produced by long chain fatty acid (LCFA) accumulation was not observed. Recovery of a currently wasted methane potential from STP-FOGW was achieved in a co-digestion process with SC-OFMSW.

Bentonite-Clay Waste Form for the Immobilization of Cesium and Strontium from Fuel Processing Waste Streams

Energy Technology Data Exchange (ETDEWEB)

Kaminski, Michael D. [Argonne National Lab. (ANL), Argonne, IL (United States); Mertz, Carol J. [Argonne National Lab. (ANL), Argonne, IL (United States)

2016-01-01

The physical properties of a surrogate waste form containing cesium, strontium, rubidium, and barium sintered into bentonite clay were evaluated for several simulant feed streams: chlorinated cobalt dicarbollide/polyethylene glycol (CCD-PEG) strip solution, nitrate salt, and chloride salt feeds. We sintered bentonite clay samples with a loading of 30 mass% of cesium, strontium, rubidium, and barium to a density of approximately 3 g/cm³. Sintering temperatures of up to 1000°C did not result in volatility of cesium. Instead, there was an increase in crystallinity of the waste form upon sintering to 1000ºC for chloride- and nitrate-salt loaded clays. The nitrate salt feed produced various cesium pollucite phases, while the chloride salt feed did not produce these familiar phases. In fact, many of the x-ray diffraction peaks could not be matched to known phases. Assemblages of silicates were formed that incorporated the Sr, Rb, and Ba ions. Gas evolution during sintering to 1000°C was significant (35% weight loss for the CCD-PEG waste-loaded clay), with significant water being evolved at approximately 600°C.

Supplementation of Morinda citrifolia waste as bioactive compound on the performances of broiler

Directory of Open Access Journals (Sweden)

I.A.K Bintang

2007-03-01

Full Text Available A study on the use of dried Morinda citrifolia waste as feed additive in broiler ration was conducted. One hundred day old chicks (doc were allocated into 4 levels (control; 0.0; 1.2; 2.4 and 4.8 g/kg feed of M. citrifolia waste with 5 replication. Each replication had 5 birds. The treatments were allocated in a completely randomized design. Variables measured were: feed intake, live weight, feed conversion ratio (FCR, percentages of carcass and internal organs ( liver. gizard, abdominal fat, and thickness of intestine. The results showed that M citrifolia waste supply did not significantly (P>0.05 affect all variables measured, but feed intake of those fed with high levels (4,8 g/kg of M. citrifolia waste was significantly (P<0.05 lower than those fed with 1.2 g/kg. FCR was significantly (P<0.05 lower as compared to the control; 1.2 and 2.4 g/kg. It is concluded that the best treatment was the supplementation of M. citrifolia waste of 4.8 g/kg, this treatment improved feed efficiency by 5% as compared to the control.

Electrochemical treatment of mixed and hazardous waste

International Nuclear Information System (INIS)

Dziewinski, J.; Marczak, S.; Smith, W.; Nuttall, E.

1995-01-01

Los Alamos National Laboratory (LANL) and The University of New Mexico are jointly developing an electrochemical process for treating hazardous and radioactive wastes. The wastes treatable by the process include toxic metal solutions, cyanide solutions, and various organic wastes that may contain chlorinated organic compounds. The main component of the process is a stack of electrolytic cells with peripheral equipment such as a rectifier, feed system, tanks with feed and treated solutions, and a gas-venting system. During the treatment, toxic metals are deposited on the cathode, cyanides are oxidized on the anode, and organic compounds are anodically oxidized by direct or mediated electrooxidation, depending on their type. Bench scale experimental studies have confirmed the feasibility of applying electrochemical systems to processing of a great variety of hazardous and mixed wastes. The operating parameters have been defined for different waste compositions using surrogate wastes. Mixed wastes are currently treated at bench scale as part of the treatability study

Aquaculture and the utilisation of plant wastes in fish feeds

CSIR Research Space (South Africa)

Jacobs, A

2010-08-31

Full Text Available shape and size of pellets vary between species and age of the fish • Feed management needs on fish farms, must be convenient, thus feed must be stable, dry, easy to handle, cost-effective © CSIR 2010 Slide 5 Plant-based feedstuffs to replace... Acids 65.4 0.77 1.4 0.7 18.3 0.8 1.5 0.7 Fermented Soya 56.1 0.68 1.7 0.6 18.4 0.8 1.6 0.6 © CSIR 2010 Slide 16 The effect of aquaculture biological agents on water quality during feeding trials • Freshwater finfish Oreochromis...

Source tracking swine fecal waste in surface water proximal to swine concentrated animal feeding operations.

Science.gov (United States)

Heaney, Christopher D; Myers, Kevin; Wing, Steve; Hall, Devon; Baron, Dothula; Stewart, Jill R

2015-04-01

Swine farming has gone through many changes in the last few decades, resulting in operations with a high animal density known as confined animal feeding operations (CAFOs). These operations produce a large quantity of fecal waste whose environmental impacts are not well understood. The purpose of this study was to investigate microbial water quality in surface waters proximal to swine CAFOs including microbial source tracking of fecal microbes specific to swine. For one year, surface water samples at up- and downstream sites proximal to swine CAFO lagoon waste land application sites were tested for fecal indicator bacteria (fecal coliforms, Escherichia coli and Enterococcus) and candidate swine-specific microbial source-tracking (MST) markers (Bacteroidales Pig-1-Bac, Pig-2-Bac, and Pig-Bac-2, and methanogen P23-2). Testing of 187 samples showed high fecal indicator bacteria concentrations at both up- and downstream sites. Overall, 40%, 23%, and 61% of samples exceeded state and federal recreational water quality guidelines for fecal coliforms, E. coli, and Enterococcus, respectively. Pig-1-Bac and Pig-2-Bac showed the highest specificity to swine fecal wastes and were 2.47 (95% confidence interval [CI]=1.03, 5.94) and 2.30 times (95% CI=0.90, 5.88) as prevalent proximal down- than proximal upstream of swine CAFOs, respectively. Pig-1-Bac and Pig-2-Bac were also 2.87 (95% CI=1.21, 6.80) and 3.36 (95% CI=1.34, 8.41) times as prevalent when 48 hour antecedent rainfall was greater than versus less than the mean, respectively. Results suggest diffuse and overall poor sanitary quality of surface waters where swine CAFO density is high. Pig-1-Bac and Pig-2-Bac are useful for tracking off-site conveyance of swine fecal wastes into surface waters proximal to and downstream of swine CAFOs and during rain events. Copyright © 2014 Elsevier B.V. All rights reserved.

Use of food waste as fish feeds: effects of prebiotic fibers (inulin and mannanoligosaccharide) on growth and non-specific immunity of grass carp (Ctenopharyngodon idella).

Science.gov (United States)

Mo, Wing Y; Cheng, Zhang; Choi, Wai M; Lun, Clare H I; Man, Yu B; Wong, James T F; Chen, Xun W; Lau, Stanley C K; Wong, Ming H

2015-11-01

The effects of inulin and mannanoligosaccharide (MOS) on the growth performance and non-specific immunity of grass carp were studied. Two doses of prebiotic fiber with 0.2 or 2% of the fibers are being mixed into fish feed pellets. Fish growth as well as selected non-specific immune parameters of grass carp were tested in a feeding trial, which lasted for 8 weeks. Fish was fed at 2.5% body mass per day. INU02, INU2, and MOS2 significantly improved relative weight gain, specific growth rate, protein efficiency ratio, and food conversion ratio of grass carp fed with food waste-based diet. In terms of non-specific immune response, grass carp showed significant improvement in all three tested parameters (total serum immunoglobin, bactericidal activity, and anti-protease activity). Adding 2% of inulin (INU2) into food waste diets seemed to be more preferable than other supplemented experimental diets (INU02, MOS02, MOS2), as it could promote growth of grass carp as well as improving the non-specific immune systems of grass carp.

Remotely replaceable fuel and feed nozzles for the NWCF calciner vessel

International Nuclear Information System (INIS)

Fletcher, R.D.; Carter, J.A.; May, K.W.

1978-01-01

The development and testing of remotely replaceable fuel and feed nozzles for calcination of liquid radioactive wastes in the calciner vessel of the New Waste Calcining Facility (NWCF) being built at the Idaho National Engineering Laboratory are described. A complete fuel nozzle assembly was fabricated and tested at the Remote Maintenance Development Facility to evolve design refinements, identify required support equipment, and develop handling techniques. The design also provided for remote replacement of the nozzle support carriage and adjacent feed and fuel pipe loops using two pairs of master-slave manipulators

OPTIMATION OF TIME AND CATALYST/FEED RATIO IN CATALYTIC CRACKING OF WASTE PLASTICS FRACTION TO GASOLINE FRACTION USING Cr/NATURAL ZEOLITE CATALYST

Directory of Open Access Journals (Sweden)

Wega Trisunaryanti

2010-06-01

Full Text Available Optimation of time and catalyst/feed ratio in catalytic cracking of waste plastics fraction to gasoline fraction using Cr/Natural Zeolite catalyst has been studied.The natural zeolite was calcined by using nitrogen gas at 500 oC for 5 hours. The chromium supported on to the zeolite was prepared by ion exchange methode with Cr(NO33.9H2O solution with chromium/zeolite concentration of 1% (w/w. The zeolite samples were then calcined  with nitrogen gas at 500 oC for 2 hours, oxidyzed with oxygen gas and reduced with hydrogen at 400 oC for 2 hours. The characterization of the zeolite catalyst by means of Si/Al ratio by UV-Vis spectroscopy, acidity with pyridine vapour adsorption and Na, Ca and Cr contents by atomic adsorption spectroscopy (AAS. The catalyst activity test was carried out in the cracking process of waste plastics fraction with boiling point range of 150 - 250 °C (consisted of C12 - C16 hydrocarbons at 450 oC for 30 min, 60 min and 90 min, and catalyst/feed ratio 1/1, 1/2, 1/3, ¼ (w/w. The result of catalyst activity test  showed  that  the maximum number  conversion of gasoline fraction (C5-C11 is 53,27% with relatively low coke formation using 1/3 catalyst/feed ratio and the cracking time of 60 min.. This  catalyst has  Si/Al ratio = 1,21 (w/w , acidity = 0,16 mmol/g and Na content = 0,81%, Ca content = 0,15% and Cr content 0,24%.   Keywords: zeolite, catalytic cracking, gasoline, chromium.

Reducing Abdominal Fat Deposition in Broiler Through Feeding Management

Directory of Open Access Journals (Sweden)

Cecep Hidayat

2015-09-01

Full Text Available Abdominal fat in broiler carcass is considered as a waste and its existence reduces the carcass quality. Abdominal fat deposition is affected by several factors such as genetic, nutrition, feed, sex, age and environment. Reducing abdominal fat deposition can be carried out by regulating the nutrient intake to ensure that no excessive nutrient was consumed. Nutrition effects to reduce abdominal fat deposition are associated with nutrient concentration of ration and quantity of daily feed intake. Daily nutrient intake can be limited, especially through restricted feeding. It is concluded that an appropriate feeding management can reduce abdominal fat deposition in broiler.

Review: Feed demand landscape and implications of food-not feed strategy for food security and climate change.

Science.gov (United States)

Makkar, H P S

2017-12-04

The food-feed competition is one of the complex challenges, and so are the ongoing climate change, land degradation and water shortage for realizing sustainable food production systems. By 2050 the global demand for animal products is projected to increase by 60% to 70%, and developing countries will have a lion's share in this increase. Currently, ~800 million tonnes of cereals (one-third of total cereal production) are used in animal feed and by 2050 it is projected to be over 1.1 billion tonnes. Most of the increase in feed demand will be in developing countries, which already face many food security challenges. Additional feed required for the projected increased demand of animal products, if met through food grains, will further exacerbate the food insecurity in these countries. Furthermore, globally, the production, processing and transport of feed account for 45% of the greenhouse gas emissions from the livestock sector. This paper presents approaches for addressing these challenges in quest for making livestock sector more sustainable. The use of novel human-inedible feed resources such as insect meals, leaf meals, protein isolates, single cell protein produced using waste streams, protein hydrolysates, spineless cactus, algae, co-products of the biofuel industry, food wastes among others, has enormous prospects. Efficient use of grasslands also offers possibilities for increasing carbon sequestration, land reclamation and livestock productivity. Opportunities also exist for decreasing feed wastages by simple and well proven practices such as use of appropriate troughs, increase in efficiency of harvesting crop residues and their conversion to complete feeds especially in the form of densified feed blocks or pellets, feeding as per the nutrient requirements, among others. Available evidence have been presented to substantiate arguments that: (a) for successful and sustained adoption of a feed technology, participation of the private sector and a sound

In situ vitrification: Application to buried waste

International Nuclear Information System (INIS)

Callow, R.A.; Thompson, L.E.

1991-01-01

Two in situ vitrification field tests were conducted in June and July 1990 at Idaho National Engineering Laboratory. In situ vitrification is a technology for in-place conversion of contaminated soils into a durable glass and crystalline waste form and is being investigated as a potential remediation technology for buried waste. The overall objective of the two tests was to assess the general suitability of the process to remediate buried waste structures found at Idaho National Engineering Laboratory. In particular, these tests were designed as part of a treatability study to provide essential information on field performance of the process under conditions of significant combustible and metal wastes, and to test a newly developed electrode feed technology. The tests were successfully completed, and the electrode feed technology provided valuable operational control for successfully processing the high metal content waste. The results indicate that in situ vitrification is a feasible technology for application to buried waste. 2 refs., 5 figs., 2 tabs

Role of breast-feeding in the prevention and treatment of diarrhoea.

Science.gov (United States)

Huffman, S L; Combest, C

1990-09-01

Recent studies have again shown the beneficial effects of breast-feeding in preventing morbidity and mortality from diarrhoea in infants. A case-control study in Brazil has shown that young infants who are not breast-fed have a 25-time greater risk of dying of diarrhoea than those who are exclusively breast-fed. A longitudinal study in the urban slums of Lima, Peru found that exclusively breast-fed infants have a reduced risk of diarrhoeal morbidity when compared with infants receiving only water in addition to breast-milk. Both these studies, along with numerous others in developing countries, point to the need to extend the duration of exclusive breast-feeding to at least 4-6 months. A review of concerned studies throughout the world shows that even in malnourished women, breast-milk output is sufficient to maintain growth of infants up to this age. The addition of early food supplements to infants fed under prevailing environmental conditions in developing countries leads to their increased diarrhoeal attacks and associated reduced food intake. This results in worsened nutritional status of the affected infants. Breast-feeding helps maintain hydration status during diarrhoeal episodes. Studies in Peru, India, and Nigeria have shown that breast-feeding can be continued during diarrhoea when the infants often refuse other foods, specially non-human milk. Thus, breast-feeding is important in providing necessary calories and protein during a time when a loss of appetite for other foods is common. Diarrhoeal disease control programmes need to modify service delivery to ensure that breast-feeding mothers are not separated from their infants while being treated with oral rehydration therapy (ORT) as inpatients or outpatients. Oral rehydration solution (ORS) should be given to infants with cup and spoon rather than bottles, in order not to interfere with suckling. When in a health system bottles are used for treatment, an implicit credibility is given to their role in

Report Task 2.3: Particulate waste and turbidity in (marine) RAS

OpenAIRE

Kals, J.; Schram, E.; Brummelhuis, E.B.M.; Bakel, van, B.

2006-01-01

Particulate waste management and removal is one of the most problematic parts of recirculation aquaculture systems (RAS). Particulate waste and thereby turbidity originates from three major sources: fish (faeces), feed and biofilm (heterotrophic bacteria and fungi). Based on size and density there are roughly four categories of particulate waste: settable, suspended, floatable and fine or dissolved solids. Specific problems related to high turbidity are a decreasing feed intake by fish, causi...

Results Of The Extraction-Scrub-Strip Testing Using An Improved Solvent Formulation And Salt Waste Processing Facility Simulated Waste

International Nuclear Information System (INIS)

Peters, T.; Washington, A.; Fink, S.

2012-01-01

The Office of Waste Processing, within the Office of Technology Innovation and Development, is funding the development of an enhanced solvent - also known as the next generation solvent (NGS) - for deployment at the Savannah River Site to remove cesium from High Level Waste. The technical effort is a collaborative effort between Oak Ridge National Laboratory (ORNL) and Savannah River National Laboratory (SRNL). As part of the program, the Savannah River National Laboratory (SRNL) has performed a number of Extraction-Scrub-Strip (ESS) tests. These batch contact tests serve as first indicators of the cesium mass transfer solvent performance with actual or simulated waste. The test detailed in this report used simulated Tank 49H material, with the addition of extra potassium. The potassium was added at 1677 mg/L, the maximum projected (i.e., a worst case feed scenario) value for the Salt Waste Processing Facility (SWPF). The results of the test gave favorable results given that the potassium concentration was elevated (1677 mg/L compared to the current 513 mg/L). The cesium distribution value, DCs, for extraction was 57.1. As a comparison, a typical D Cs in an ESS test, using the baseline solvent formulation and the typical waste feed, is ∼15. The Modular Caustic Side Solvent Extraction Unit (MCU) uses the Caustic-Side Solvent Extraction (CSSX) process to remove cesium (Cs) from alkaline waste. This process involves the use of an organic extractant, BoBCalixC6, in an organic matrix to selectively remove cesium from the caustic waste. The organic solvent mixture flows counter-current to the caustic aqueous waste stream within centrifugal contactors. After extracting the cesium, the loaded solvent is stripped of cesium by contact with dilute nitric acid and the cesium concentrate is transferred to the Defense Waste Processing Facility (DWPF), while the organic solvent is cleaned and recycled for further use. The Salt Waste Processing Facility (SWPF), under

Preliminary low-level waste feed definition guidance - LLW pretreatment interface

International Nuclear Information System (INIS)

Shade, J.W.; Connor, J.M.; Hendrickson, D.W.; Powell, W.J.; Watrous, R.A.

1995-02-01

The document describes limits for key constituents in the LLW feed, and the bases for these limits. The potential variability in the stream is then estimated and compared to the limits. Approaches for accomodating uncertainty in feed inventory, processing strategies, and process design (melter and disposal system) are discussed. Finally, regulatory constraints are briefly addressed

Addition of liquid waste incineration capability to the INEL's low-level waste incinerator

International Nuclear Information System (INIS)

Steverson, E.M.; Clark, D.P.; McFee, J.N.

1986-01-01

A liquid waste system has recently been installed in the Waste Experimental Reduction Facility (WERF) incinerator at the Idaho National Engineering Laboratory (INEL). In this paper, aspects of the incineration system such as the components, operations, capabilities, capital cost, EPA permit requirements, and future plans are discussed. The principal objective of the liquid incineration system is to provide the capability to process hazardous, radioactively contaminated, non-halogenated liquid wastes. The system consists primarily of a waste feed system, instrumentation and controls, and a liquid burner, which were procured at a capital cost of $115,000

A survey on the starting age of complementary feeding and some of its associated factors in the breast-feeding infants (Semnan, Iran

Directory of Open Access Journals (Sweden)

A. Shahbazi

2007-11-01

Full Text Available Introduction: There is a relationship between children’s survival, development and health and theirfeeding. Malnutrition is a common complication in most of the developing countries. Complementaryfeeding begins in infants when they can not obtain enough energy and nutrients from mother’s milk.Both early and late beginning of complementary nutrition lead to severe complications, and suitableage for feeding in infants is after month 6. The present study was performed to estimate the age ofbeginning of complementary feeding and related factors in infants of Semnan.Materials&Methods: In this cross sectional study, 400 infants aged 6-12 months were analized viaquestionnaire. In each of 8 health centers in Semnan, 50 mothers who referred to health care centers,filled up questionnaires.Results: 76.3% of mothers begin the complementary feeding from 6 months after delivery. Themost common complementary food, which was used, was cereal (69.5%. Mean (±SD beginning ageof complementary feeding was 5.86±0.60 month. Most of mothers (97.5% had been receivedinformation about infant’s feeding through appointments, books, vaccination card and pamphlet priorto their infants reach to age 6 month. There was a significant relationship between occupation ofmother (P=0.049, age of mother (P=0.040, father's educational level (P=0.002, type of delivery(P=0.015 and the beginning age of complementary feeding. However, no significant relationship wasobserved between gender, type of milk, birth order, type of health care center, mother's educationallevel, first complementary feeding, type of mother's education and the beginning age ofcomplementary feeding.Conclusion: The findings of current study showed that 97.5% of mothers were educated forbeginning of complementary feeding in a suitable time; however, about 23% of them didn’t begincomplementary feeding in an appropriate time. Therefore, it seems more effective education isnecessary to give by health care centers

Tank waste remediation system retrieval and disposal mission key enabling assumptions

International Nuclear Information System (INIS)

Baldwin, J.H.

1998-01-01

An overall systems approach has been applied to develop action plans to support the retrieval and immobilization waste disposal mission. The review concluded that the systems and infrastructure required to support the mission are known. Required systems are either in place or plans have been developed to ensure they exist when needed. The review showed that since October 1996 a robust system engineering approach to establishing integrated Technical Baselines, work breakdown structures, tank farm structure and configurations and work scope and costs has been established itself as part of the culture within TWRS. An analysis of the programmatic, management and technical activities necessary to declare readiness to proceed with execution of the mission demonstrates that the system, people and hardware will be on line and ready to support the private contractors. The systems approach included defining the retrieval and immobilized waste disposal mission requirements and evaluating the readiness of the TWRS contractor to supply waste feed to the private contractors in June 2OO2. The Phase 1 feed delivery requirements from the Private Contractor Request for Proposals were reviewed. Transfer piping routes were mapped out, existing systems were evaluated, and upgrade requirements were defined. Technical Basis Reviews were completed to define work scope in greater detail, cost estimates and associated year by year financial analyses were completed. TWRS personnel training, qualifications, management systems and procedures were reviewed and shown to be in place and ready to support the Phase 1B mission. Key assumptions and risks that could negatively impact mission success were evaluated and appropriate mitigative actions plans were planned and scheduled

MITS Feed and Withdrawal Subsystem: operating procedures

International Nuclear Information System (INIS)

Brown, W.S.

1980-01-01

This procedure details the steps required to provide continuous feed flow and withdrawal of process product and waste flows in support of thruput operation in the cascade or its elements. It particularly requires operator attention to safety considerations

Analysis of SRP waste streams for waste tank certification

International Nuclear Information System (INIS)

Coleman, C.J.

1989-01-01

The Savannah River Plant (SRP) will apply for certification from the State of South Carolina to operate the SRP High-Level Waste Tanks. The permit application will be submitted as a RCRA Part B, Volume 16, entitled ''RCRA Part B Application For the F and H-Area Radioactive Waste Farm.'' RCRA regulations require that influent and effluent streams of hazardous waste sites be characterized to obtain an operating permit. The Waste Management Technology Department requested ADD to determine 21 components (including pH and weight percent solids) in the current influent streams to SRP High-Level Waste Tanks. The analyses will be used to supplement existing data on the composition of High-Level Waste. Effluent streams, which will feed Saltstone and the DWPF, will be analyzed when they are produced. This report contains the data obtained from analyzing key influent streams to SRP High-Level Waste Tanks. The precision of the data and the analytical methods that were used are also discussed

Radioactive wastes storage and disposal. Chapter 8

International Nuclear Information System (INIS)

2002-01-01

The Chapter 8 is essentially dedicated to radioactive waste management - storage and disposal. The management safety is being provided due to packages and facilities of waste disposal and storage. It is noted that at selection of sites for waste disposal it is necessary account rock properties and ways of the wastes delivery pathways

Method of decontamination for uranium oxide particles floating in liquid waste

International Nuclear Information System (INIS)

Terakado, Tsutomu; Ebara, Tsuneo; Sato, Kuniaki.

1981-01-01

Purpose: To rapidly treat liquid waste containing uranium oxide particles floating in it and to enable substantially complete decontamination. Method: An iron salt such as ferrous sulfate or the like is added to liquid waste with floating uranium oxide particles, an alkaline solution such as caustic soda or the like is then added to the liquid waste while feeding compressed air at 0.1 to 0.02 l/sec. per ton of liquid waste, and the pH of the liquid waste is made to from 6.5 to 7.5. Thereafter, the feed of compressed air is stopped, the liquid waste is allowed to stand, and is then filtered. (Aizawa, K.)

Performances of broiler supplemented with antibiotic and Morinda citrifolia waste as sources of bioactive compounds

Directory of Open Access Journals (Sweden)

I.A.K Bintang

2008-03-01

Full Text Available A study on the use of Zinc bacitracin antibiotic (ZnB and dried Morinda citrifolia waste as feed additive in broiler ration was conducted. Two hundred and sixteen day old chicks (DOC was allocated into 4 treatments: control; control + 50 ppm ZnB, and control + M. citrifolia waste at 2 levels (5 and 10 g/kg ration with 9 replications. Each replicatation consist of 6 birds. The treatments were allocated in a completely randomized design. Variables measured were feed intake, live weight, feed conversion ratio (FCR, percentages of carcass and internal organs (liver, gizard, abdominal fat, and thickness of intestine. The results showed that feed intake of M. citrifolia waste was significantly (P0.05 from that of control. The use of M. citrifolia waste (5 and 10 g/kg gave significantly lower (P0.05, but was significantly lower (P0,05 than that of control, control + antibiotic ZnB and M. citrifolia waste 5g/kg. It is concluded that the supplementation of M. citrifolia waste (5 g/kg could substitute ZnB to improve feed eficiency in broiler ration.

Assessment of feeding value of vegetable-carried pineapple fruit ...

African Journals Online (AJOL)

This study compared the sun-drying characteristics of five blends each (w/w; 1:1, 1:1.5, 1:2, 1:2.5, 1:3) of wheat offal-carried pineapple waste (WO:PW) and brewers' dried grains-carried pineapple waste (BDG:PW), assessed the blends for their nutrient contents and the feeding value of the optimum blends with Red Sokoto ...

A simple approach to recycle broiler litter as animal feed | Makinde ...

African Journals Online (AJOL)

Broiler litter (BL) is a major waste from poultry production that constitutes serious disposal and environmental pollution problems globally despite its potential as animal feed. Therefore, the objective of this study was to develop a simple procedure for converting broiler litter into animal feed using wheat offal (WO) and cattle ...

Nutritive value of tea (Camellia sinensis, Linn) waste for cattle

Energy Technology Data Exchange (ETDEWEB)

Ananthasubramaniam, C R; Menachery, M

1977-01-01

Tea waste, the residue of instant tea manufacturing, was subjected to feeding trails in cattle in order to find out its nutritive value. The material possesses a digestable crude protein of 9.7% and a total digestible N of 43.0%. The total tanins represented only 1.9%. Results indicated that tea waste is a potential feed source for livestock.

Waste acceptance and waste loading for vitrified Oak Ridge tank waste

International Nuclear Information System (INIS)

Harbour, J.R.; Andrews, M.K.

1997-01-01

The Office of Science and Technology of the DOE has funded a joint project between the Oak Ridge National Laboratory (ORNL) and the Savannah River Technology Center (SRTC) to evaluate vitrification and grouting for the immobilization of sludge from ORNL tank farms. The radioactive waste is from the Gunite and Associated Tanks (GAAT), the Melton Valley Storage Tanks (MVST), the Bethel Valley Evaporator Service Tanks (BVEST), and the Old Hydrofractgure Tanks (OHF). Glass formulation development for sludge from these tanks is discussed in an accompanying article for this conference (Andrews and Workman). The sludges contain transuranic radionuclides at levels which will make the glass waste form (at reasonable waste loadings) TRU. Therefore, one of the objectives for this project was to ensure that the vitrified waste form could be disposed of at the Waste Isolation Pilot Plant (WIPP). In order to accomplish this, the waste form must meet the WIPP Waste Acceptance Criteria (WAC). An alternate pathway is to send the glass waste forms for disposal at the Nevada Test Site (NTS). A sludge waste loading in the feed of 6 wt percent will lead to a waste form which is non-TRU and could potentially be disposed of at NTS. The waste forms would then have to meet the requirements of the NTS WAC. This paper presents SRTC''s efforts at demonstrating that the glass waste form produced as a result of vitrification of ORNL sludge will meet all the criteria of the WIPP WAC or NTS WAC

Tank waste concentration mechanism study

International Nuclear Information System (INIS)

Pan, L.C.; Johnson, L.J.

1994-09-01

This study determines whether the existing 242-A Evaporator should continue to be used to concentrate the Hanford Site radioactive liquid tank wastes or be replaced by an alternative waste concentration process. Using the same philosophy, the study also determines what the waste concentration mechanism should be for the future TWRS program. Excess water from liquid DST waste should be removed to reduce the volume of waste feed for pretreatment, immobilization, and to free up storage capacity in existing tanks to support interim stabilization of SSTS, terminal cleanout of excess facilities, and other site remediation activities

Potential Human Health Risks of Tannery Waste-contaminated Poultry Feed

Directory of Open Access Journals (Sweden)

Mohammad Latiful Bari

2015-01-01

Conclusions. The estimated daily intake value, THQ, along with the aggregate hazard index value, indicated a potential risk to consumers through consumption of contaminated chicken. Therefore, the study results clearly demonstrate heavy metals accumulation in chicken due to feeding SCW-based feed. The contaminated chicken further transfers these heavy metals to humans through ingestion. Hence, there is a potential human health risk through consumption of contaminated chicken meat.

Early-Life Events, Including Mode of Delivery and Type of Feeding, Siblings and Gender, Shape the Developing Gut Microbiota.

Science.gov (United States)

Martin, Rocio; Makino, Hiroshi; Cetinyurek Yavuz, Aysun; Ben-Amor, Kaouther; Roelofs, Mieke; Ishikawa, Eiji; Kubota, Hiroyuki; Swinkels, Sophie; Sakai, Takafumi; Oishi, Kenji; Kushiro, Akira; Knol, Jan

2016-01-01

Colonization of the infant gut is believed to be critically important for a healthy growth as it influences gut maturation, metabolic, immune and brain development in early life. Understanding factors that influence this process is important, since an altered colonization has been associated with a higher risk of diseases later in life. Fecal samples were collected from 108 healthy neonates in the first half year of life. The composition and functionality of the microbiota was characterized by measuring 33 different bacterial taxa by qPCR/RT qPCR, and 8 bacterial metabolites. Information regarding gender, place and mode of birth, presence of siblings or pets; feeding pattern and antibiotic use was collected by using questionnaires. Regression analysis techniques were used to study associations between microbiota parameters and confounding factors over time. Bacterial DNA was detected in most meconium samples, suggesting bacterial exposure occurs in utero. After birth, colonization by species of Bifidobacterium, Lactobacillus and Bacteroides was influenced by mode of delivery, type of feeding and presence of siblings, with differences found at species level and over time. Interestingly, infant-type bifidobacterial species such as B. breve or B. longum subsp infantis were confirmed as early colonizers apparently independent of the factors studied here, while B. animalis subsp. lactis presence was found to be dependent solely on the type of feeding, indicating that it might not be a common infant gut inhabitant. One interesting and rather unexpected confounding factor was gender. This study contributes to our understanding of the composition of the microbiota in early life and the succession process and the evolution of the microbial community as a function of time and events occurring during the first 6 months of life. Our results provide new insights that could be taken into consideration when selecting nutritional supplementation strategies to support the

Early-Life Events, Including Mode of Delivery and Type of Feeding, Siblings and Gender, Shape the Developing Gut Microbiota.

Directory of Open Access Journals (Sweden)

Rocio Martin

Full Text Available Colonization of the infant gut is believed to be critically important for a healthy growth as it influences gut maturation, metabolic, immune and brain development in early life. Understanding factors that influence this process is important, since an altered colonization has been associated with a higher risk of diseases later in life. Fecal samples were collected from 108 healthy neonates in the first half year of life. The composition and functionality of the microbiota was characterized by measuring 33 different bacterial taxa by qPCR/RT qPCR, and 8 bacterial metabolites. Information regarding gender, place and mode of birth, presence of siblings or pets; feeding pattern and antibiotic use was collected by using questionnaires. Regression analysis techniques were used to study associations between microbiota parameters and confounding factors over time. Bacterial DNA was detected in most meconium samples, suggesting bacterial exposure occurs in utero. After birth, colonization by species of Bifidobacterium, Lactobacillus and Bacteroides was influenced by mode of delivery, type of feeding and presence of siblings, with differences found at species level and over time. Interestingly, infant-type bifidobacterial species such as B. breve or B. longum subsp infantis were confirmed as early colonizers apparently independent of the factors studied here, while B. animalis subsp. lactis presence was found to be dependent solely on the type of feeding, indicating that it might not be a common infant gut inhabitant. One interesting and rather unexpected confounding factor was gender. This study contributes to our understanding of the composition of the microbiota in early life and the succession process and the evolution of the microbial community as a function of time and events occurring during the first 6 months of life. Our results provide new insights that could be taken into consideration when selecting nutritional supplementation strategies to

Waste-efficient materials procurement for construction projects: A structural equation modelling of critical success factors.

Science.gov (United States)

Ajayi, Saheed O; Oyedele, Lukumon O

2018-05-01

Albeit the understanding that construction waste is caused by activities ranging from all stages of project delivery process, research efforts have been concentrated on design and construction stages, while the possibility of reducing waste through materials procurement process is widely neglected. This study aims at exploring and confirming strategies for achieving waste-efficient materials procurement in construction activities. The study employs sequential exploratory mixed method approach as its methodological framework, using focus group discussion, statistical analysis and structural equation modelling. The study suggests that for materials procurement to enhance waste minimisation in construction projects, the procurement process would be characterised by four features. These include suppliers' commitment to low waste measures, low waste purchase management, effective materials delivery management and waste-efficient Bill of Quantity, all of which have significant impacts on waste minimisation. This implies that commitment of materials suppliers to such measures as take back scheme and flexibility in supplying small materials quantity, among others, are expected of materials procurement. While low waste purchase management stipulates the need for such measures as reduced packaging and consideration of pre-assembled/pre-cut materials, efficient delivery management entails effective delivery and storage system as well as adequate protection of materials during the delivery process, among others. Waste-efficient specification and bill of quantity, on the other hand, requires accurate materials take-off and ordering of materials based on accurately prepared design documents and bill of quantity. Findings of this study could assist in understanding a set of measures that should be taken during materials procurement process, thereby corroborating waste management practices at other stages of project delivery process. Copyright © 2018. Published by Elsevier Ltd.

40 CFR 63.1204 - What are the standards for hazardous waste burning cement kilns that are effective until...

Science.gov (United States)

2010-07-01

... Principal Organic Hazardous Constituents (POHCs) in the waste feed that you specify under paragraph (c)(3... in the hazardous waste feed, considering the results of hazardous waste analyses or other data and... waste burning cement kilns that are effective until compliance with the standards under § 63.1220? 63...

Relation of supplementary feeding to resumptions of menstruation and ovulation in lactating postpartum women.

Science.gov (United States)

Li, Wei; Qiu, Yi

2007-05-20

Resumption of menstrual cycles is one of the indicators for restoration of reproductive capability in postpartum women. However, menstruation does not necessarily mean that ovulation has taken place. The aim of this study was to investigate the relation of supplementary feeding to return of menstruation and ovulation after delivery. A questionnaire was used to obtain data from 101 breastfeeding mothers. The following elements were analyzed: age, education level, breastfeeding practice, time of return of menstruation, contraceptive practice, and starting time of supplementary feeding during the lactation at intervals of 6 weeks to 18 months after delivery. The ovulation was continuously monitored by ultrasonography and basal body temperature (BBT) measurement. By ultrasonography, 53 of the 101 women (52.5%) had the first ovulation (follicle > 1.8 cm in diameter) within 154 days after delivery on average, among whom 11 (10.9%, 11/101) had restoration of ovulation within 4 months and 42 (41.6%, 42/101) had it after 4 months. In women with follicles > 1.8 cm in diameter (n = 53), the menstruation resumed (138 +/- 84) days after delivery, and the supplementary feeding was started at (4.0 +/- 1.1) months, which were significantly earlier than those in the women with follicular diameter menstruation before the end of ultrasonographic monitoring, while only 8 in the women with follicular diameter menstruation (n = 100, r = 0.4764, P < 0.01) and first ovulation after delivery (n = 53, r = 0.5554, P < 0.01). In this series, no woman had pregnancy within 18 months postpartum. Supplementary feeding can affect the restoration of menstrual cycles and ovulation in lactating postpartum women.

Application of thermo-analytical techniques in nuclear waste management

International Nuclear Information System (INIS)

Raje, Naina; Ghonge, Darshana K.; Reddy, A.V.R.

2015-01-01

Sodium nitrate solution is the byproduct of nuclear fuel reprocessing plant. It is produced during the neutralization of nitric acid received through purex process and stored in tanks or immobilized in bitumen/cement at site as waste packets. In order to minimize the environmental impact due to these waste packets, it is desirable to reduce nitrate ion to harmless gases like nitrogen. Biodegradation, ion exchange, electrodialysis and chemical treatment are the methods for nitrate reduction in the case of non nuclear industrial waste. Chemical treatment seems to be the most viable process to treat the waste from nuclear reprocessing plant in comparison to the other methods used for the non nuclear industrial waste. During chemical treatment, the nitrate ions can be converted to nitrogen by using a suitable reductant in presence of a catalyst. Formaldehyde has been chosen as the reducing agent for the nitrate - nitrogen conversion and in the process, formaldehyde gets converted to formic acid. In order to optimize the reduction process, it is essential to determine the formaldehyde and formic acid content in the waste feed solution and no direct analytical methodology is available for the same. Present work describes the attempts made to apply evolved gas analysis for understanding the mechanism of conversion of formaldehyde to formic acid. The developed method can be applied for the qualitative/quantitative determination of formaldehyde and formic acid in the waste feed solution. Waste feed samples were received from PSDD, BARC

Support for HLW Direct Feed - Phase 2, VSL-15R3440-1

Energy Technology Data Exchange (ETDEWEB)

Matlack, K. S. [The Catholic Univ. of America, Washington, DC (United States); Pegg, I. [The Catholic Univ. of America, Washington, DC (United States); Joseph, I. [EnergySolutions, Columbia, MD (United States); Kot, W. K. [The Catholic Univ. of America, Washington, DC (United States)

2017-03-20

This report describes work performed to develop and test new glass and feed formulations originating from a potential flow-sheet for the direct vitrification of High Level Waste (HLW) with minimal or no pretreatment. In the HLW direct feed option that is under consideration for early operations at the Hanford Tank Waste Treatment and Immobilization Plant (WTP), the pretreatment facility would be bypassed in order to support an earlier start-up of the vitrification facility. For HLW, this would mean that the ultrafiltration and caustic leaching operations that would otherwise have been performed in the pretreatment facility would either not be performed or would be replaced by an interim pretreatment function (in-tank leaching and settling, for example). These changes would likely affect glass formulations and waste loadings and have impacts on the downstream vitrification operations. Modification of the pretreatment process may result in: (i) Higher aluminum contents if caustic leaching is not performed; (ii) Higher chromium contents if oxidative leaching is not performed; (iii) A higher fraction of supernate in the HLW feed resulting from the lower efficiency of in-tank washing; and (iv) A higher water content due to the likely lower effectiveness of in-tank settling compared to ultrafiltration. The HLW direct feed option has also been proposed as a potential route for treating HLW streams that contain the highest concentrations of fast-settling plutoniumcontaining particles, thereby avoiding some of the potential issues associated with such particles in the WTP Pretreatment facility [1]. In response, the work presented herein focuses on the impacts of increased supernate and water content on wastes from one of the candidate source tanks for the direct feed option that is high in plutonium.

Monitoring total mixed rations and feed delivery systems.

Science.gov (United States)

Oelberg, Thomas J; Stone, William

2014-11-01

This article is intended to give practitioners a method to evaluate total mixed ration (TMR) consistency and to give them practical solutions to improve TMR consistency that will improve cattle performance and health. Practitioners will learn how to manage the variation in moisture and nutrients that exists in haylage and corn silage piles and in bales of hay, and methods to reduce variation in the TMR mixing and delivery process. Copyright © 2014 Elsevier Inc. All rights reserved.

Control of high level radioactive waste-glass melters

International Nuclear Information System (INIS)

Bickford, D.F.; Choi, A.S.

1991-01-01

Slurry Fed Melters (SFM) are being developed in the United States, Europe and Japan for the conversion of high-level radioactive waste to borosilicate glass for permanent disposal. The high transition metal, noble metal, nitrate, organic, and sulfate contents of these wastes lead to unique melter redox control requirements. Pilot waste-glass melter operations have indicated the possibility of nickel sulfide or noble-metal fission-product accumulation on melter floors, which can lead to distortion of electric heating patterns, and decrease melter life. Sulfide formation is prevented by control of the redox chemistry of the melter feed. The redox state of waste-glass melters is determined by balance between the reducing potential of organic compounds in the feed, and the oxidizing potential of gases above the melt, and nitrates and polyvalent elements in the waste. Semiquantitative models predicting limitations of organic content have been developed based on crucible testing. Computerized thermodynamic computations are being developed to predict the sequence and products of redox reactions and is assessing process variations. Continuous melter test results have been compared to improved computer staged-thermodynamic-models of redox behavior. Feed chemistry control to prevent sulfide and moderate noble metal accumulations are discussed. 17 refs., 3 figs

enhancing pineaple waste utilization as animalfeed through nutrient

African Journals Online (AJOL)

Rose

2013-10-23

Oct 23, 2013 ... that fermentation of pineapple waste by solid state fermentation using the fungi A. niger and T. viride significantly (P < 0.05) ... The conventional commercial feeds ... waste management, biomass energy conservation and.

40 CFR 63.1203 - What are the standards for hazardous waste incinerators that are effective until compliance with...

Science.gov (United States)

2010-07-01

... (POHCs) in the waste feed that you specify under paragraph (c)(3)(ii) of this section to the extent... hazardous waste and on their concentration or mass in the hazardous waste feed, considering the results of... waste incinerators that are effective until compliance with the standards under § 63.1219? 63.1203...

Improved mixing and sampling systems for vitrification melter feeds

International Nuclear Information System (INIS)

Ebadian, M.A.

1998-01-01

This report summarizes the methods used and results obtained during the progress of the study of waste slurry mixing and sampling systems during fiscal year 1977 (FY97) at the Hemispheric Center for Environmental Technology (HCET) at Florida International University (FIU). The objective of this work is to determine optimal mixing configurations and operating conditions as well as improved sampling technology for defense waste processing facility (DWPF) waste melter feeds at US Department of Energy (DOE) sites. Most of the research on this project was performed experimentally by using a tank mixing configuration with different rotating impellers. The slurry simulants for the experiments were prepared in-house based on the properties of the DOE sites' typical waste slurries. A sampling system was designed to withdraw slurry from the mixing tank. To obtain insight into the waste mixing process, the slurry flow in the mixing tank was also simulated numerically by applying computational fluid dynamics (CFD) methods. The major parameters investigated in both the experimental and numerical studies included power consumption of mixer, mixing time to reach slurry uniformity, slurry type, solids concentration, impeller type, impeller size, impeller rotating speed, sampling tube size, and sampling velocities. Application of the results to the DWPF melter feed preparation process will enhance and modify the technical base for designing slurry transportation equipment and pipeline systems. These results will also serve as an important reference for improving waste slurry mixing performance and melter operating conditions. These factors will contribute to an increase in the capability of the vitrification process and the quality of the waste glass

Radicidation and radappertization of animal feeds in Israel, 1968-1977

International Nuclear Information System (INIS)

Lapidot, M.

1979-01-01

Contamination of animal feed and animal products with salmonellae and other enteric microorganisms has considerably increased in recent years. This has resulted in commensurate increases in the incidence of salmonellosis and other enteric diseases in both animals and humans. The development of radappertization for laboratory animal feeds and of radicidation for farm animal feeds over the last ten years in Israel is reviewed. The products considered were radappertized feeds for SPF rodent colonies and for commercial SPF poultry flocks, and radicidized feed for breeder and broiler flocks. In the latter case microbiological, biological, technological and economic aspects are considered. The petition and clearance for radicidized poultry feed are briefly discussed. The potential use of radicidation in the preparation of animal feeds from organic wastes, i.e. putrescibles in household garbage and sewage sludge, is outlined, and the factors involved are evaluated. (author)

Improved Management of the Technical Interfaces Between the Hanford Tank Farm Operator and the Hanford Waste Treatment Plant - 13383

International Nuclear Information System (INIS)

Duncan, Garth M.; Saunders, Scott A.

2013-01-01

The Department of Energy (DOE) is constructing the Waste Treatment and Immobilization Plant (WTP) at the Hanford site in Washington to treat and immobilize approximately 114 million gallons of high level radioactive waste (after all retrievals are accomplished). In order for the WTP to be designed and operated successfully, close coordination between the WTP engineering, procurement, and construction contractor, Bechtel National, Inc. and the tank farms operating contractor (TOC), Washington River Protection Solutions, LLC, is necessary. To develop optimal solutions for DOE and for the treatment of the waste, it is important to deal with the fact that two different prime contractors, with somewhat differing contracts, are tasked with retrieving and delivering the waste and for treating and immobilizing that waste. The WTP and the TOC have over the years cooperated to manage the technical interface. To manage what is becoming a much more complicated interface as the WTP design progresses and new technical issues have been identified, an organizational change was made by WTP and TOC in November of 2011. This organizational change created a co-located integrated project team (IPT) to deal with mutual and interface issues. The Technical Organization within the One System IPT includes employees from both TOC and WTP. This team has worked on a variety of technical issues of mutual interest and concern. Technical issues currently being addressed include: - The waste acceptance criteria; - Waste feed delivery and the associated data quality objectives (DQO); - Evaluation of the effects of performing a riser cut on a single shell tank on WTP operations; - The disposition of secondary waste from both TOC and WTP; - The close coordination of the TOC double shell tank mixing and sampling program and the Large Scale Integrated Test (LSIT) program for pulse jet mixers at WTP along with the associated responses to the Defense Nuclear Facilities Safety Board (DNFSB) Recommendation

Improved Management of the Technical Interfaces Between the Hanford Tank Farm Operator and the Hanford Waste Treatment Plant - 13383

Energy Technology Data Exchange (ETDEWEB)

Duncan, Garth M. [Bechtel National Inc., 2435 Stevens Center Place, Richland, Washington, 99352 (United States); Saunders, Scott A. [Washington River Protection Solutions, P.O. Box 850, Richland, Washington, 99352 (United States)

2013-07-01

The Department of Energy (DOE) is constructing the Waste Treatment and Immobilization Plant (WTP) at the Hanford site in Washington to treat and immobilize approximately 114 million gallons of high level radioactive waste (after all retrievals are accomplished). In order for the WTP to be designed and operated successfully, close coordination between the WTP engineering, procurement, and construction contractor, Bechtel National, Inc. and the tank farms operating contractor (TOC), Washington River Protection Solutions, LLC, is necessary. To develop optimal solutions for DOE and for the treatment of the waste, it is important to deal with the fact that two different prime contractors, with somewhat differing contracts, are tasked with retrieving and delivering the waste and for treating and immobilizing that waste. The WTP and the TOC have over the years cooperated to manage the technical interface. To manage what is becoming a much more complicated interface as the WTP design progresses and new technical issues have been identified, an organizational change was made by WTP and TOC in November of 2011. This organizational change created a co-located integrated project team (IPT) to deal with mutual and interface issues. The Technical Organization within the One System IPT includes employees from both TOC and WTP. This team has worked on a variety of technical issues of mutual interest and concern. Technical issues currently being addressed include: - The waste acceptance criteria; - Waste feed delivery and the associated data quality objectives (DQO); - Evaluation of the effects of performing a riser cut on a single shell tank on WTP operations; - The disposition of secondary waste from both TOC and WTP; - The close coordination of the TOC double shell tank mixing and sampling program and the Large Scale Integrated Test (LSIT) program for pulse jet mixers at WTP along with the associated responses to the Defense Nuclear Facilities Safety Board (DNFSB) Recommendation

What’s in a Dog’s Breakfast? Considering the Social, Veterinary and Environmental Implications of Feeding Food Scraps to Pets Using Three Australian Surveys

Directory of Open Access Journals (Sweden)

Kirrilly Thompson

2015-06-01

Full Text Available Diverting food waste away from landfills is one way to minimise its serious environmental impact. Given that over a third of Australian households have at least one pet, the feeding of food waste to dogs constitutes one potentially significant waste diversion path. However, the proportion of dog owners that feed food waste to their pets is unknown. Moreover, there has been no investigation into any relationship between practices of feeding scraps to pets and the animals’ body condition, living arrangements (inside or outside and exercise regime. To provide some insight, this paper presents findings from three surveys across two Australian studies. The first reports both pet and dog-specific findings from two surveys within a wider food waste research project (n = 1017, establishing that 28% of respondents fed leftovers to pets as a main food waste minimization strategy, yet in only 5% of households did this constitute more than half of the household’s food scraps. This modest diversion of food scraps from landfill to feeding pets was reflected in the finding that there was no significant difference seen in the claimed level of food discards to the waste stream for households feeding food scraps to dogs and those that did not. The second—a dog owner specific study (n = 355—found that almost half (44% of respondents reported feeding table scraps to dogs. They were more likely to be females, owners of medium sized dogs, and in larger households. There was no significant difference in self-rated dogs’ body condition scores between respondents who fed table scraps to their dog and those who did not. Further multidisciplinary research is recommended to reconcile the social, veterinary and environmental risks and benefits of feeding food waste to animals.

Treatment of alpha-bearing combustible wastes using acid digestion

International Nuclear Information System (INIS)

Lerch, R.E.; Allen, C.R.; Blasewitz, A.G.

1978-01-01

Acid digestion has been developed at the Hanford Engineering Development Laboratory (HEDL) in Richland, Washington to reduce the volume of combustible nuclear waste materials, while converting them to an inert, noncombustible residue. A 100 kg/day test unit has recently been constructed to demonstrate the process using radioactively contaminated combustible wastes. The unit, called the Radioactive Acid Digestion Test Unit (RADTU) was completed in September 1977 and is currently undergoing cold shakedown tests. Hot operation is expected in May 1978. Features of RADTU include: storage and transfer station for incoming wastes, a feed preparation station, an extrusion feed mechanism for transfer of the waste to the acid digester, the acid digester a residue recovery system, and an off-gas treatment system

Treatment of alpha-bearing combustible wastes using acid digestion

International Nuclear Information System (INIS)

Lerch, R.E.; Allen, C.R.; Blasewitz, A.G.

1977-11-01

Acid digestion has been developed at the Hanford Engineering Development Laboratory (HEDL) in Richland, Washington to reduce the volume of combustible nuclear waste materials, while converting them to an inert, noncombustible residue. A 100 kg/day test unit has recently been constructed to demonstrate the process using radioactively contaminated combustible wastes. The unit, called the Radioactive Acid Digestion Test Unit (RADTU) was completed in September 1977 and is currently undergoing cold shakedown tests. Hot operation is expected in May 1978. Features of RADTU include: storage and transfer station for incoming wastes, a feed preparation station, an extrusion feed mechanism for transfer of the waste to the acid digester, the acid digester, a residue recovery system, and an off-gas treatment system

Gasifier feed: Tailor-made from Illinois coals

Energy Technology Data Exchange (ETDEWEB)

Ehrlinger, H.P. III.

1991-01-01

The purpose of this research is to develop a coal slurry from waste streams using Illinois coal that is ideally suited for a gasification feed. The principle items to be studied are (1) methods of concentrating pyrite and decreasing other ash forming minerals into a high grade gasification feed using froth flotation and gravity separation techniques; (2) chemical and particle size analyses of coal slurries; (3) determination of how that slurry can be densified and to what degree of densification is optimum from the pumpability and combustibility analyses; and (4) reactivity studies.

Plasma filtering techniques for nuclear waste remediation.

Science.gov (United States)

Gueroult, Renaud; Hobbs, David T; Fisch, Nathaniel J

2015-10-30

Nuclear waste cleanup is challenged by the handling of feed stocks that are both unknown and complex. Plasma filtering, operating on dissociated elements, offers advantages over chemical methods in processing such wastes. The costs incurred by plasma mass filtering for nuclear waste pretreatment, before ultimate disposal, are similar to those for chemical pretreatment. However, significant savings might be achieved in minimizing the waste mass. This advantage may be realized over a large range of chemical waste compositions, thereby addressing the heterogeneity of legacy nuclear waste. Copyright © 2015 Elsevier B.V. All rights reserved.

Tank waste remediation system retrieval and disposal mission readiness-to-proceed guidance and requirements to deliverables crosswalk

International Nuclear Information System (INIS)

Hall, C.E.

1998-01-01

In September 1996, the US Department of Energy, Richland Operations Office (RL) initiated the first of a two-phase program to remediate waste storage in tanks at the Hanford Site in Washington State. Initiating the first phase, RL signed contracts with two private companies who agreed to receive and vitrify a portion of the tank waste in a demonstration and to return the vitrified product and by-products to the Project Management Hanford Contract (PHMC) team for disposition. The first phase of the overall remediation effort is a demonstration of treatment concepts, and the second phase includes treatment of the remaining tank wastes. The demonstration phase, Phase 1 of the project, is further subdivided into two parts, A and B. During Phase 1A, the vitrification contractors are to establish the technical, operational, regulatory, business, and financial elements required to provide treatment services on a fixed unit price basis. Phase 1A deliverables will be evaluated by RL to determine whether it is in the best interest of the government to have one or more vitrification contractors proceed with Phase 1B, in which 6% to 13% of the tank waste would be treated in the demonstration. In addition, before RL can authorize proceeding with Phase 1B, the PHMC team must demonstrate its readiness to retrieve and deliver the waste to the private contractor(s) and to receive and dispose of the products and by-products returned from the treatment. The PHMC team has organized their plans for providing these vitrification-support services into the Retrieval and Disposal Mission within the Tank Waste Remediation System (TWRS) Project. Three RL core teams were established to assist in evaluating the PHMC team's readiness specifically in regard to three task areas: Waste feed delivery; Infrastructure and by-products delivery; and Immobilized products. The core teams each developed a set of criteria and plans to be used in evaluating the PHMC team's readiness to proceed (RTP)

TWRS retrieval and storage mission. Immobilized low-activity waste disposal plan

International Nuclear Information System (INIS)

Shade, J.W.

1998-01-01

expected to be completed in 2025. DOE will supply the feed to the private contractors and will receive the ILAW product from the private treatment facilities during Phase 1. For Phase 2, retrieval and feed delivery, as well as waste treatment and immobilization, will be done by private contractors. DOE will pay the private contractors for each ILAW package that meets the product specifications as stated in the RFP or subsequently negotiated. Acceptance of immobilized waste will be based on private contractor activities to qualify, verify, document, and certify the product and DOE activities to audit, review, inspect, and evaluate the treatment and immobilization process and products. The acceptance process is expected to result in ILAW product packages certified for transport and disposal at the Hanford Site safely and in compliance with environmental regulations

Double Shell Tank (DST) Transfer Piping Subsystem Specification

International Nuclear Information System (INIS)

GRAVES, C.E.

2000-01-01

This specification establishes the performance requirements and provides references to the requisite codes and standards to be applied during design of the Double-Shell Tank (DST) Transfer Piping Subsystem that supports the first phase of Waste Feed Delivery. This specification establishes the performance requirements and provides references to the requisite codes and standards to be applied during design of the Double-Shell Tank (DST) Transfer Piping Subsystem that supports the first phase of waste feed delivery. This subsystem transfers waste between transfer-associated structures (pits) and to the River Protection Project (RPP) Privatization Contractor Facility where it will be processed into an immobilized waste form. This specification is intended to be the basis for new projects/installations (W-521, etc.). This specification is not intended to retroactively affect previously established project design criteria without specific direction by the program

Utilization of irradiated sludge for fish feed

International Nuclear Information System (INIS)

Harsojo; Syamsu, Suwirma; Subagyo, Lydia Andini

1994-01-01

An experiment was conducted to study the use of irradiated sludge pellet for fish feed, namely pellet A consisting of irradiated sludge and shrimp waste (1:3); pellet B consisting of irradiated sludge and commercial pellet (1:2). Pellet C, which is a commercial fish feed, was used as control. Catfish (Clarias gariepinus) was used in this experiment. The feed pellet with a dose of 5% of total body weight was given 3 times per day. The results of the experiments showed that based on food conversion for the relative growth of the catfishes, and heavy metal content, pellet A was the best. No contamination of Salmonella or Shigella bacteria was detected in each pellet. (author). 8 refs, 3 tabs, 1 fig

Reducing Abdominal Fat Deposition in Broiler Through Feeding Management

OpenAIRE

Cecep Hidayat

2015-01-01

Abdominal fat in broiler carcass is considered as a waste and its existence reduces the carcass quality. Abdominal fat deposition is affected by several factors such as genetic, nutrition, feed, sex, age and environment. Reducing abdominal fat deposition can be carried out by regulating the nutrient intake to ensure that no excessive nutrient was consumed. Nutrition effects to reduce abdominal fat deposition are associated with nutrient concentration of ration and quantity of daily feed intak...

The role of frit in nuclear waste vitrification

International Nuclear Information System (INIS)

Vienna, J.D.; Smith, P.A.; Dorn, D.A.; Hrma, P.

1994-04-01

Vitrification of nuclear waste requires additives which are often vitrified independently to form a frit. Frit composition is formulated to meet the needs of glass composition and processing. The effects of frit on melter feed and melt processing, glass acceptance, and waste loading is of practical interest in understanding the trade-offs associated with the competing demands placed on frit composition. Melter feed yield stress, viscosity and durability of frits and corresponding waste glasses as well as the kinetics of elementary melting processes have been measured. The results illustrate the competing requirements on frit. Four frits (FY91, FY93, HW39-4, and SR202) and simulated neutralized current acid waste (NCAW) were used in this study. The experimental evidence shows that optimization of frit for one processing related property often results in poorer performance for the remaining properties. The difficulties associated with maximum waste loading and durability are elucidated for glasses which could be processed using technology available for the previously proposed Hanford Waste Vitrification Plant

40 CFR 260.22 - Petitions to amend part 261 to exclude a waste produced at a particular facility.

Science.gov (United States)

2010-07-01

... the manufacturing processes or other operations and feed materials producing the waste and an assessment of whether such processes, operations, or feed materials can or might produce a waste that is not... a waste produced at a particular facility. 260.22 Section 260.22 Protection of Environment...

Hanford Waste Vitrification Plant applied technology plan

International Nuclear Information System (INIS)

Kruger, O.L.

1990-09-01

This Applied Technology Plan describes the process development, verification testing, equipment adaptation, and waste form qualification technical issues and plans for resolution to support the design, permitting, and operation of the Hanford Waste Vitrification Plant. The scope of this Plan includes work to be performed by the research and development contractor, Pacific Northwest Laboratory, other organizations within Westinghouse Hanford Company, universities and companies with glass technology expertise, and other US Department of Energy sites. All work described in this Plan is funded by the Hanford Waste Vitrification Plant Project and the relationship of this Plan to other waste management documents and issues is provided for background information. Work to performed under this Plan is divided into major areas that establish a reference process, develop an acceptable glass composition envelope, and demonstrate feed processing and glass production for the range of Hanford Waste Vitrification Plant feeds. Included in this work is the evaluation and verification testing of equipment and technology obtained from the Defense Waste Processing Facility, the West Valley Demonstration Project, foreign countries, and the Hanford Site. Development and verification of product and process models and other data needed for waste form qualification documentation are also included in this Plan. 21 refs., 4 figs., 33 tabs

Transition in Infant and Young Child Feeding Practices in India.

Science.gov (United States)

Puri, Seema

2017-01-01

Optimal infant and young child feeding, which includes initiation of breastfeeding within one hour of birth, exclusive breastfeeding for first six months, age appropriate complementary feeding after six months along with continued breastfeeding for 2 years and beyond, is a public health intervention to prevent child morbidity, mortality and malnutrition [1]. In India, even though institutional delivery rates are increasing, only 44% women are able to breastfeed their babies within one hour of delivery. While 65% children are exclusively breast fed for the first six months, the median duration of breastfeeding is 24.4 months and complementary feeding rates are 50%. To achieve optimal IYCF practices, each woman should have access to a community based IYCF counseling support system. Efforts are therefore needed to upgrade skill based training of health workers and revive and update the Baby Friendly Hospital Initiative (BFHI). To promote and sustain breastfeeding amongst working women, it is essential to ensure adequate maternity leave, crèches at work place, flexible working hours, and provision of physical space for breast feeding at work place. It is imperative to also create public awareness about the dangers of bottle and formula feeding and to provide accurate information on the appropriate complementary food to be given to infants. In conclusion, India needs to make serious efforts to overcome malnutrition with not only prioritized IYCF policies but also their effective implementation in place. Copyright© Bentham Science Publishers; For any queries, please email at epub@benthamscience.org.

Radioactive waste shredding: Preliminary evaluation

International Nuclear Information System (INIS)

Soelberg, N.R.; Reimann, G.A.

1994-07-01

The critical constraints for sizing solid radioactive and mixed wastes for subsequent thermal treatment were identified via a literature review and a survey of shredding equipment vendors. The types and amounts of DOE radioactive wastes that will require treatment to reduce the waste volume, destroy hazardous organics, or immobilize radionuclides and/or hazardous metals were considered. The preliminary steps of waste receipt, inspection, and separation were included because many potential waste treatment technologies have limits on feedstream chemical content, physical composition, and particle size. Most treatment processes and shredding operations require at least some degree of feed material characterization. Preliminary cost estimates show that pretreatment costs per unit of waste can be high and can vary significantly, depending on the processing rate and desired output particle size

The policy effects of feed-in tariff and renewable portfolio standard: A case study of China's waste incineration power industry.

Science.gov (United States)

Xin-Gang, Zhao; Yu-Zhuo, Zhang; Ling-Zhi, Ren; Yi, Zuo; Zhi-Gong, Wu

2017-10-01

Among the regulatory policies, feed-in tariffs (FIT) and renewable portfolio standards (RPS) are the most popular to promote the development of renewable energy power industry. They can significantly contribute to the expansion of domestic industrial activities in terms of sustainable energy. This paper uses system dynamics (SD) to establish models of long-term development of China's waste incineration power industry under FIT and RPS schemes, and provides a case study by using scenario analysis method. The model, on the one hand, not only clearly shows the complex logical relationship between the factors but also assesses policy effects of the two policy tools in the development of the industry. On the other hand, it provides a reference for scholars to study similar problems in different countries, thereby facilitating an understanding of waste incineration power's long-term sustainable development pattern under FIT and RPS schemes, and helping to provide references for policy-making institutions. The results show that in the perfect competitive market, the implementation of RPS can promote long-term and rapid development of China's waste incineration power industry given the constraints and actions of the mechanisms of RPS quota proportion, the TGC valid period, and fines, compared with FIT. At the end of the paper, policy implications are offered as references for the government. Copyright © 2017 Elsevier Ltd. All rights reserved.

Redox reaction and foaming in nuclear waste glass melting

Energy Technology Data Exchange (ETDEWEB)

Ryan, J.L.

1995-08-01

This document was prepared by Pacific Northwest Laboratory (PNL) and is an attempt to analyze and estimate the effects of feed composition variables and reducing agent variables on the expected chemistry of reactions occurring in the cold cap and in the glass melt in the nuclear waste glass Slurry-fed, joule-heated melters as they might affect foaming during the glass-making process. Numerous redox reactions of waste glass components and potential feed additives, and the effects of other feed variables on these reactions are reviewed with regard to their potential effect on glass foaming. A major emphasis of this report is to examine the potential positive or negative aspects of adjusting feed with formic acid as opposed to other feed modification techniques including but not limited to use of other reducing agents. Feed modification techniques other than the use of reductants that should influence foaming behavior include control of glass melter feed pH through use of nitric acid. They also include partial replacement of sodium salts by lithium salts. This latter action (b) apparently lowers glass viscosity and raises surface tension. This replacement should decrease foaming by decreasing foam stability.

Mixing Modeling Analysis For SRS Salt Waste Disposition

International Nuclear Information System (INIS)

Lee, S.

2011-01-01

Nuclear waste at Savannah River Site (SRS) waste tanks consists of three different types of waste forms. They are the lighter salt solutions referred to as supernate, the precipitated salts as salt cake, and heavier fine solids as sludge. The sludge is settled on the tank floor. About half of the residual waste radioactivity is contained in the sludge, which is only about 8 percentage of the total waste volume. Mixing study to be evaluated here for the Salt Disposition Integration (SDI) project focuses on supernate preparations in waste tanks prior to transfer to the Salt Waste Processing Facility (SWPF) feed tank. The methods to mix and blend the contents of the SRS blend tanks were evalutaed to ensure that the contents are properly blended before they are transferred from the blend tank such as Tank 50H to the SWPF feed tank. The work consists of two principal objectives to investigate two different pumps. One objective is to identify a suitable pumping arrangement that will adequately blend/mix two miscible liquids to obtain a uniform composition in the tank with a minimum level of sludge solid particulate in suspension. The other is to estimate the elevation in the tank at which the transfer pump inlet should be located where the solid concentration of the entrained fluid remains below the acceptance criterion (0.09 wt% or 1200 mg/liter) during transfer operation to the SWPF. Tank 50H is a Waste Tank that will be used to prepare batches of salt feed for SWPF. The salt feed must be a homogeneous solution satisfying the acceptance criterion of the solids entrainment during transfer operation. The work described here consists of two modeling areas. They are the mixing modeling analysis during miscible liquid blending operation, and the flow pattern analysis during transfer operation of the blended liquid. The modeling results will provide quantitative design and operation information during the mixing/blending process and the transfer operation of the blended

Infant feeding practices in Malaysia.

Science.gov (United States)

Chen, S T

1978-12-01

Retrospective nutritional data on 100 children, aged 6 months to 2 1/2 years, who were admitted to the University Hospital in Kuala Lumpur, Malaysia, was obtained by interviewing the mothers of the children. Analysis of the data revealed that 1) only 49% of the children were breast-fed as infants; 2) 50% of the mothers who did breast-feed discontinued breast-feeding before the children were 3 months old; and 3) the weaning diet of at least 1/3 of the children was inadequate. 18% of the children were Malays, 49% were Chinese, and 33% were Indian. The proportion of breast-fed children was highest among the Malays and lowest among the Chinese. Mothers with higher incomes tended to stop breast-feeding earlier than mothers with lower incomes. 67% of the women said they stopped breast-feeding due to inadequate lactation. Most of the children received supplementary foods at relatively early ages. 50% of the infants received starchy foods by the time they were 3 1/2 months old, and 50% received fruit or fruit juice by the time they were 3 1/2 months old. Vegetable products, meat, fish, and eggs were not added to the diet until the children were considerably older. Recommendations, based on the study findings, were 1) hospitals should discontinue the practice of deferring breast-feeding initiation for 24 hours after delivery; 2) mothers should be encouraged to breast-feed fully; and 3) health personnel should discourage the widespread use of costly precooked cereals for supplementary feeding. Tables depicted 1) the frequency distribution of the 100 children by income and by milk feeding patterns according to ethnic affiliation and 2) the cost of serving precooked cereals as compared to the cost of serving home cooked meals.

Fly larvae as sustainable bioconverters of waste for feed in the future

DEFF Research Database (Denmark)

Nordentoft, Steen; Aabo, Søren

2014-01-01

How to provide enough food and feed for the growing population is a major challenge for the nextgeneration. Improved economy in many developing countries increases the demand for protein from meator fish. This may lead to depletion of the seas and overexploitation of agricultural land in the in s......How to provide enough food and feed for the growing population is a major challenge for the nextgeneration. Improved economy in many developing countries increases the demand for protein from meator fish. This may lead to depletion of the seas and overexploitation of agricultural land......, or nutrients may be refined fromprocessed insects, however there is a huge need for technological development in order to automateculture and harvest of the insects.In nature insects and insect larvae are important feed sources for poultry and the larva of the commonhouse fly (Musca domestica) have been shown...... to be especially rich in essential amino and fatty acids. Atthe Food institute we have investigated in feed safety of using these fly larvae as feed for egg laying hens.The larvae were reared on poultry manure which implies the risk of transmission of pathogenicmicroorganism between animals and to humans, as well...

Computational Fluid Dynamics Modeling Of Scaled Hanford Double Shell Tank Mixing - CFD Modeling Sensitivity Study Results

International Nuclear Information System (INIS)

Jackson, V.L.

2011-01-01

The primary purpose of the tank mixing and sampling demonstration program is to mitigate the technical risks associated with the ability of the Hanford tank farm delivery and celtification systems to measure and deliver a uniformly mixed high-level waste (HLW) feed to the Waste Treatment and Immobilization Plant (WTP) Uniform feed to the WTP is a requirement of 24590-WTP-ICD-MG-01-019, ICD-19 - Interface Control Document for Waste Feed, although the exact definition of uniform is evolving in this context. Computational Fluid Dynamics (CFD) modeling has been used to assist in evaluating scaleup issues, study operational parameters, and predict mixing performance at full-scale.

Greenhouse effect reduction and energy recovery from waste landfill

Energy Technology Data Exchange (ETDEWEB)

Lombardi, Lidia [Dipartimento di Energetica ' Sergio Stecco' , Universita degli Studi di Firenze, Via Santa Marta 3, 50139 Florence (Italy)]. E-mail: lidia.lombardi@pin.unifi.it; Carnevale, Ennio [Dipartimento di Energetica ' Sergio Stecco' , Universita degli Studi di Firenze, Via Santa Marta 3, 50139 Florence (Italy); Corti, Andrea [Dipartimento di Ingegneria dell' Informazione, Universita degli Studi di Siena, Via Roma 56, 53100 Siena (Italy)

2006-12-15

Waste management systems are a non-negligible source of greenhouse gases. In particular, methane and carbon dioxide emissions occur in landfills due to the breakdown of biodegradable carbon compounds operated on by anaerobic bacteria. The conventional possibilities of reducing the greenhouse effect (GHE) from waste landfilling consists in landfill gas (LFG) flaring or combustion with energy recovery in reciprocating engines. These conventional treatments are compared with three innovative possibilities: the direct LFG feeding to a fuel cell (FC); the production of a hydrogen-rich gas, by means of steam reforming and CO{sub 2} capture, to feed a stationary FC; the production of a hydrogen-rich gas, by means of steam reforming and CO{sub 2} capture, to feed a vehicle FC. The comparison is carried out from an environmental point of view, calculating the specific production of GHE per unit mass of waste disposed in landfill equipped with the different considered technologies.

Observance of who ten steps towards successful breast feeding; a survey from postpartum mothers

International Nuclear Information System (INIS)

Masood, S.; Rahman, M.U.; Mahmood, H.; Faisal, T.; Maroof, S.; Qureshi, A.M.

2016-01-01

Background: Breast feeding is a physiological phenomenon, nonetheless, this act is a learned behaviour that requires continuous active support to make it successful. This study determines the frequency of mothers practicing successful breast feeding according to the WHO ten steps at tertiary care hospital. Methods: A descriptive cross sectional study was conducted in the Obstetrics department of Military Hospital, Rawalpindi over six month duration from July to December 2014. Booked mothers aged 15-49 years, having given birth to healthy, singleton baby were included in the study. Questions were asked after taking written informed consent from the mothers after delivery. Data was entered and analysed on SPSS version 20. Results: Out of 148 mothers, 35 (23.7 percentage) mothers were following successful breast feeding, i.e., knew 7 or more steps. A total of 100 (67.6 percentage) mothers received support for breast feeding by healthcare staff during their stay in hospital while 19 (12.8 percentage) mothers started breast feeding within one hour. About 71 percentage had started formula milk along with breast feeding. About 127 (85.8 percentage) reported that they fed their children on demand and 144 (97.3 percentage) did not use dummies. Statistically significant difference was observed as housewife mothers gave no top feed (p=0.005) and multiparous mothers started breast feeding within one hour of delivery (p=0.04). Conclusion: The steps to achieve successful breast feeding are followed to a small extent among mothers. Delayed initiation of breast feeding and increasing trend towards use of formula feed was observed. Employed, primiparous mothers are the most sensitive group to be focused during antenatal period. (author)

Nuclear criticality safety analysis summary report: The S-area defense waste processing facility

International Nuclear Information System (INIS)

Ha, B.C.

1994-01-01

The S-Area Defense Waste Processing Facility (DWPF) can process all of the high level radioactive wastes currently stored at the Savannah River Site with negligible risk of nuclear criticality. The characteristics which make the DWPF critically safe are: (1) abundance of neutron absorbers in the waste feeds; (2) and low concentration of fissionable material. This report documents the criticality safety arguments for the S-Area DWPF process as required by DOE orders to characterize and to justify the low potential for criticality. It documents that the nature of the waste feeds and the nature of the DWPF process chemistry preclude criticality

Issues related to volatilization, phase alteration, and presence of unreacted feed in the borosilicate glass wasteform

International Nuclear Information System (INIS)

Jain, V.

1994-01-01

The U.S. Department of Energy's Office of Civilian Radioactive Waste Management has outlined the requirements in the Waste Acceptance Product Specifications (WAPS) that must be met before they will accept West Valley canistered vitrified waste forms for shipment to a federal depository. In this study the glass volatilization was studied using a thermogravimetric analyzer (TGA) to evaluate the absence of free gases, free liquids, explosives, pyrophorics, combustibles, and organics in the waste form. The total carbon in the samples was analyzed using a carbon determinator, phase alteration by heat-treating samples for extended periods of time (45-day) at T g -10 degrees C and T g +10 degrees C (where T g is the glass transition temperature), and the presence of unreacted feed in glass by comparing x-ray diffraction (XRD) patterns for glass and dried feed. The results of this study indicate that the West Valley vitrification process completely transforms the feed into glass. Also the TGA, XRD, and scanning transmission electron microscopy data indicates that there is no significant volatilization, redox reactions, and phase alterations in the waste form up to more than 200 degrees C above the T g . 7 refs., 1 fig., 4 tabs

Waste disposal options report. Volume 2

International Nuclear Information System (INIS)

Russell, N.E.; McDonald, T.G.; Banaee, J.; Barnes, C.M.; Fish, L.W.; Losinski, S.J.; Peterson, H.K.; Sterbentz, J.W.; Wenzel, D.R.

1998-02-01

Volume 2 contains the following topical sections: estimates of feed and waste volumes, compositions, and properties; evaluation of radionuclide inventory for Zr calcine; evaluation of radionuclide inventory for Al calcine; determination of k eff for high level waste canisters in various configurations; review of ceramic silicone foam for radioactive waste disposal; epoxides for low-level radioactive waste disposal; evaluation of several neutralization cases in processing calcine and sodium-bearing waste; background information for EFEs, dose rates, watts/canister, and PE-curies; waste disposal options assumptions; update of radiation field definition and thermal generation rates for calcine process packages of various geometries-HKP-26-97; and standard criteria of candidate repositories and environmental regulations for the treatment and disposal of ICPP radioactive mixed wastes

Waste disposal options report. Volume 2

Energy Technology Data Exchange (ETDEWEB)

Russell, N.E.; McDonald, T.G.; Banaee, J.; Barnes, C.M.; Fish, L.W.; Losinski, S.J.; Peterson, H.K.; Sterbentz, J.W.; Wenzel, D.R.

1998-02-01

Volume 2 contains the following topical sections: estimates of feed and waste volumes, compositions, and properties; evaluation of radionuclide inventory for Zr calcine; evaluation of radionuclide inventory for Al calcine; determination of k{sub eff} for high level waste canisters in various configurations; review of ceramic silicone foam for radioactive waste disposal; epoxides for low-level radioactive waste disposal; evaluation of several neutralization cases in processing calcine and sodium-bearing waste; background information for EFEs, dose rates, watts/canister, and PE-curies; waste disposal options assumptions; update of radiation field definition and thermal generation rates for calcine process packages of various geometries-HKP-26-97; and standard criteria of candidate repositories and environmental regulations for the treatment and disposal of ICPP radioactive mixed wastes.

Promotion of breast feeding in the community: impact of health education programme in rural communities in Nigeria.

Science.gov (United States)

Davies-Adetugbo, A A

1996-03-01

Breast feeding has been recognized as a child survival strategy, while breast feeding programmes have been increasingly implemented in many communities. This study assesses the effectiveness of a breast feeding education programme launched through the primary health care programme in the rural communities of Nigeria. Late trimester pregnant women were enrolled into the study and given a questionnaire on knowledge, attitudes, and practices (KAP) about breast feeding. Women in the study group (n = 126) received breast feeding counselling before and after delivery, while those in control group (n = 130) did not receive any counselling. Both groups were monitored after delivery and followed with the KAP questionnaire. The results of the study showed marked improvements in the intervention group for colostrum feeding (p = 0.0000). Moreover, 31.6% of the mothers in the intervention group practised timely initiation of breast feeding compared to 5.6% of the controls, and the prevalence of exclusive breast feeding at 4 months was 39.8% in the intervention group compared to 13.9% for the controls. Multivariate analysis showed that the intervention was a powerful and the only significant predictor of the increase in breast feeding behaviours (p = 0.0000), and that an early initiation of breast feeding is a strong predictor of exclusive breast feeding at 4 months of age. It is concluded that breast feeding promotion in rural communities is feasible and can lead to behavioural changes.

α-waste conditioning concepts on the basis of waste arisings, actinide distribution and their influence on final disposal products

International Nuclear Information System (INIS)

Krause, H.; Scheffler, K.

1978-01-01

Among the wastes arising from the reprocessing and Pu-fuel element fabrication plants, only seven waste streams contain the major part of the actinides going into the radioactive waste. It is shown that the liquid α-waste from fuel element fabrication, the high level liquid waste, and the active fraction of the medium level liquid waste can be incorporated into borosilicate glass. Wet combustion of solid burnable waste allows a relatively easy and complete recovery of plutonium. Leached hulls, sludges from feed clarification and solid non-combustible wastes can be incorporated into concrete. These treatment methods guarantee that only relatively small amounts of high quality α-bearing residues have to be disposed of

Fuel optimization in a multi chamber incinerator by the moisture control of oily sludge and medical wastes

International Nuclear Information System (INIS)

Haider, I.; Hussain, S.; Khan, S.; Mehran, T.

2011-01-01

Experiments have been performed to study the effects of %age moisture content on fuel optimization during the waste feed combustion of oily sludge, medical waste and mix blend waste in a 50 kg/hr multi chamber incinerator installed at NCPC- ARL RWP. Intention is to find out the optimum and in compliance with NEQs incinerator performance at various moisture contents in the different waste feeds. Optimum performances of the incinerator, so that optimum operating moisture conditions, which has been used for multi purpose waste, feeds, may be defined. Three waste feeds of 10 kg batch size were used for the experimentation namely; Oily Sludge, Medical waste and Mix blend waste (oily sludge and medical), with the primary chamber preheating temperature 655 deg. C for 15 mins. interval monitoring. The secondary chamber temperature was set to 850 deg. C. By the data obtained it is apparent that rising the waste moisture content tend to increase fuel consumption specifically in case of medical waste and hence lowering the overall combustion efficiency. In the emissions the CO/sub 2/ concentration is showing the incineration efficiency. Higher efficiency of the system could have been achieved by increasing the CO/sub 2/ in the gases leaving the incinerator, lower fuel usage per kg waste feed and maintain proper operating conditions. Fuel consumption for the oily sludge with 10% moisture content, was found to be least as compared with the same %age of medical waste and mix blend waste. However environmental compliance of the operation is shown by the flue gas analysis. The results shows that using mix blend(oily sludge and medical) waste having 12-13% moisture content would be suitable for incineration in multi-chamber incinerator .Other makes it possible to determine the optimum incinerator temperature control settings and operating conditions, as well as to assure continuous, efficient, environmentally satisfactory operation. The optimum fuel consumption for 10 kg each waste

Role of district municipalities in waste management in South Africa

CSIR Research Space (South Africa)

Afrika, M

2010-10-01

Full Text Available Service delivery has become a source of much tension and protests in South Africa (Delivery, 2009) with fifty two major service delivery protests reported for the period January to August 2009 (COGTA, 2009). Failing waste management services, is a...

Disposing of fluid wastes

International Nuclear Information System (INIS)

Bradley, J.S.

1984-01-01

Toxic liquid waste, eg liquid radioactive waste, is disposed of by locating a sub-surface stratum which, before removal of any fluid, has a fluid pressure in the pores thereof which is less than the hydrostatic pressure which is normal for a stratum at that depth in the chosen area, and then feeding the toxic liquid into the stratum at a rate such that the fluid pressure in the stratum never exceeds the said normal hydrostatic pressure. (author)

The use of poultry waste as a dietary supplement for ruminants

International Nuclear Information System (INIS)

Saleh, H.M.; Elwan, K.M.; El-Fouly, H.A.; Ibrahim, I.I.; Salama, A.M.; Elashry, M.A.

2002-01-01

The use of poultry waste as a dietary supplement in ruminant ration could have a considerable effect on reducing costs, insufficiency of protein in diet, and on solving disposal problems. The chemical composition of poultry waste and its safe use in ruminant nutrition were investigated prior to its use as a dietary supplement. No appreciable differences in chemical composition were noted in poultry wastes between oven and sun dried forms. The high content of protein, energy, and minerals in poultry waste indicated its importance as a partial substitute for concentrates in the diet. The numbers of total bacteria and pathogenic microorganisms such as Salmonella and E. coli detected in poultry waste were within the acceptable limits. Farm testing of rations containing poultry wastes were carried out on sheep (ewes and lambs), Friesian cattle and buffalo heifers. In ewes fed during late pregnancy and lactation, milk yield and performance did not show any significant changes. Lambs suckled from ewes fed on poultry waste did not show any significant difference in weaning weight, average daily weight gain or feed efficiency (kg feed used/kg weaned weight). However, the poultry waste group had shorter age at weaning than the control group. In another feeding trial on growing lambs after weaning, mean daily body weight gain was higher in lambs fed on a ration containing poultry waste than the control ration. In Friesian and buffalo calves, no significant differences in average daily body weight gain were found as a result of inclusion of poultry waste in the ration. In buffalo heifers various estimated reproductive parameters indicated no appreciable differences due to the inclusion of poultry waste in the diet except that the number of ovulations and number of services/conception were both higher in the group fed with poultry waste. (author)

High-Level waste process and product data annotated bibliography

International Nuclear Information System (INIS)

Stegen, G.E.

1996-01-01

The objective of this document is to provide information on available issued documents that will assist interested parties in finding available data on high-level waste and transuranic waste feed compositions, properties, behavior in candidate processing operations, and behavior on candidate product glasses made from those wastes. This initial compilation is only a partial list of available references

The Mixed Waste Management Facility. Preliminary design review

International Nuclear Information System (INIS)

1995-01-01

This document presents information about the Mixed Waste Management Facility. Topics discussed include: cost and schedule baseline for the completion of the project; evaluation of alternative options; transportation of radioactive wastes to the facility; capital risk associated with incineration; radioactive waste processing; scaling of the pilot-scale system; waste streams to be processed; molten salt oxidation; feed preparation; initial operation to demonstrate selected technologies; floorplans; baseline revisions; preliminary design baseline; cost reduction; and project mission and milestones

Pediatric Enteric Feeding Techniques: Insertion, Maintenance, and Management of Problems

International Nuclear Information System (INIS)

Nijs, Els L. F.; Cahill, Anne Marie

2010-01-01

Enteral feeding is considered a widespread, well-accepted means of delivering nutrition to adults and children who are unable to consume food by mouth or who need support in maintaining adequate nutrition for a variety of reasons, including acute and chronic disease states. Delivery of enteral feeding to nutritionally deprived patients may be achieved by several means. In this article, the indications and insertion of enteral access in children will be reviewed. In addition, common complications and management of problems will be discussed.

Logistics and feed preparation of straw for gasification and combustion

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

The system for supply of biomass comprises the entire chain from harvest to feeding. The subsequent energy process makes demands on the quality of the biomass that is supplied. The process, moreover, makes a number of demands on the preceding pretreatment and the equipment subsequently utilised. The straw delivery and handling system ought therefore to be considered as a coherent unit whole consisting of the following: harvesting and collection; storage; transportation; fragmentizing; drying; densification; handling at the plants; feeding; `subsequent process`. (EG)

Remediation and production of low-sludge high-level waste glasses

International Nuclear Information System (INIS)

Ramsey, W.G.; Brown, K.G.; Beam, D.C.

1994-01-01

High-level radioactive sludge will constitute 24-28 oxide weight percent of the high-level waste glass produced at the Savannah River Site. A recent melter campaign using non-radioactive, simulated feed was performed with a sludge content considerably lower than 24 percent. The resulting glass was processed and shown to have acceptable durability. However, the durability was lower than predicted by the durability algorithm. Additional melter runs were performed to demonstrate that low sludge feed could be remediated by simply adding sludge oxides. The Product Composition Control System, a computer code developed to predict the proper feed composition for production of high-level waste glass, was utilized to determine the necessary chemical additions. The methodology used to calculate the needed feed additives, the effects of sludge oxides on glass production, and the resulting glass durability are discussed

Vectra GSI, Inc. low-level waste melter testing Phase 1 test report

Energy Technology Data Exchange (ETDEWEB)

Stegen, G.E.; Wilson, C.N.

1996-02-21

A multiphase program was initiated in 1994 to test commercially available melter technologies for the vitrification of the low-level waste (LLW) stream from defense wastes stored in underground tanks at the Hanford Site in southeastern Washington State. Vectra GSI, Inc. was one of seven vendors selected for Phase 1 of the melter demonstration tests using simulated LLW that were completed during fiscal year 1995. The attached report prepared by Vectra GSI, Inc. describes results of melter testing using slurry feed and dried feeds. Results of feed drying and prereaction tests using a fluid bed calciner and rotary dryer also are described.

Vectra GSI, Inc. low-level waste melter testing Phase 1 test report

International Nuclear Information System (INIS)

Stegen, G.E.; Wilson, C.N.

1996-01-01

A multiphase program was initiated in 1994 to test commercially available melter technologies for the vitrification of the low-level waste (LLW) stream from defense wastes stored in underground tanks at the Hanford Site in southeastern Washington State. Vectra GSI, Inc. was one of seven vendors selected for Phase 1 of the melter demonstration tests using simulated LLW that were completed during fiscal year 1995. The attached report prepared by Vectra GSI, Inc. describes results of melter testing using slurry feed and dried feeds. Results of feed drying and prereaction tests using a fluid bed calciner and rotary dryer also are described

Physicochemical Characteristics, in Vitro Fermentation Indicators, Gas Production Kinetics, and Degradability of Solid Herbal Waste as Alternative Feed Source for Ruminants

Directory of Open Access Journals (Sweden)

A. N. Kisworo

2017-08-01

Full Text Available The aims of this research were to study the nutrient and secondary metabolite contents of solid herbal wastes (SHW that were preserved by freeze drying, sun drying and silage, as well as to analyze their effects on in vitro fermentation indicators i.e., gas production kinetics and degradability of solid herbal waste. Physical and chemical properties on three forms of SHW (sun dry, freeze dry, and silage were characterized and then an in vitro gas production experiment was performed to determine the kinetics of gas production, methane production, NH3, microbial protein, and SHW degradability. Polyethylene glycol (PEG was added to the three treatments to determine the biological activity of tannins. Results showed that all three preparations of SHW still contained high nutrient and plant secondary metabolite contents. Gas production, methane, NH3, microbial protein, in vitro degradability of dry matter (IVDMD and organic matter (IVDOM of SHW silage were lower (P<0.05 compared to sun dry and freeze dry. These results were apparently due to the high content of secondary metabolites especially tannin. It can be concluded that solid herbal wastes (SHW can be used as an alternative feed ingredients for ruminants with attention to the content of secondary metabolites that can affect the process of fermentation and digestibility in the rumen.

Effect of melter feed foaming on heat flux to the cold cap

Science.gov (United States)

Lee, SeungMin; Hrma, Pavel; Pokorny, Richard; Klouzek, Jaroslav; VanderVeer, Bradley J.; Dixon, Derek R.; Luksic, Steven A.; Rodriguez, Carmen P.; Chun, Jaehun; Schweiger, Michael J.; Kruger, Albert A.

2017-12-01

The glass production rate, which is crucial for the nuclear waste cleanup lifecycle, is influenced by the chemical and mineralogical nature of melter feed constituents. The choice of feed materials affects both the conversion heat and the thickness of the foam layer that forms at the bottom of the cold cap and controls the heat flow from molten glass. We demonstrate this by varying the alumina source, namely, substituting boehmite or corundum for gibbsite, in a high-alumina high-level-waste melter feed. The extent of foaming was determined using the volume expansion test and the conversion heat with differential scanning calorimetry. Evolved gas analysis was used to identify gases responsible for the formation of primary and secondary foam. The foam thickness, a critical factor in the rate of melting, was estimated using known values of heat conductivities and melting rates. The result was in reasonable agreement with the foam thickness experimentally observed in quenched cold caps from the laboratory-scale melter.

Effect of melter feed foaming on heat flux to the cold cap

Energy Technology Data Exchange (ETDEWEB)

Lee, SeungMin; Hrma, Pavel; Pokorny, Richard; Klouzek, Jaroslav; VanderVeer, Bradley J.; Dixon, Derek R.; Luksic, Steven A.; Rodriguez, Carmen P.; Chun, Jaehun; Schweiger, Michael J.; Kruger, Albert A.

2017-12-01

The glass production rate, which is crucial for the nuclear waste cleanup lifecycle, is influenced by the chemical and mineralogical nature of melter feed constituents. The choice of feed materials affects both the conversion heat and the thickness of the foam layer that forms at the bottom of the cold cap and controls the heat flow from molten glass. We demonstrate this by varying the alumina source, namely, substituting boehmite or corundum for gibbsite, in a high-alumina high-level-waste melter feed. The extent of foaming was determined using the volume expansion test and the conversion heat with differential scanning calorimetry. Evolved gas analysis was used to identify gases responsible for the formation of primary and secondary foam. The foam thickness, a critical factor in the rate of melting, was estimated using known values of heat conductivities and melting rates. The result was in reasonable agreement with the foam thickness experimentally observed in the laboratory-scale melter.

Recovery of fissile materials from plutonium residues, miscellaneous spent nuclear fuel, and uranium fissile wastes

International Nuclear Information System (INIS)

Forsberg, C.W.

1997-01-01

A new process is proposed that converts complex feeds containing fissile materials into a chemical form that allows the use of existing technologies (such as PUREX and ion exchange) to recover the fissile materials and convert the resultant wastes to glass. Potential feed materials include (1) plutonium scrap and residue, (2) miscellaneous spent nuclear fuel, and (3) uranium fissile wastes. The initial feed materials may contain mixtures of metals, ceramics, amorphous solids, halides, and organics. 14 refs., 4 figs

Hanford Waste Vitrification Plant capacity increase options

International Nuclear Information System (INIS)

Larson, D.E.

1996-04-01

Studies are being conducted by the Hanford Waste Vitrification Plant (HWVP) Project on ways to increase the waste processing capacity within the current Vitrification Building structural design. The Phase 1 study on remote systems concepts identification and extent of capacity increase was completed. The study concluded that the HWVP capacity could be increased to four times the current capacity with minor design adjustments to the fixed facility design, and the required design changes would not impact the current footprint of the vitrification building. A further increase in production capacity may be achievable but would require some technology development, verification testing, and a more systematic and extensive engineering evaluation. The primary changes included a single advance melter with a higher capacity, new evaporative feed tank, offgas quench collection tank, ejector venturi scrubbers, and additional inner canister closure station,a smear test station, a new close- coupled analytical facility, waste hold capacity of 400,000 gallon, the ability to concentrate out-of-plant HWVP feed to 90 g/L waste oxide concentration, and limited changes to the current base slab construction package

Audit of feeding practices in the neonatal wards at the Charlotte ...

African Journals Online (AJOL)

better nutritional outcomes, including protecting against obesity in ... Background. Breastfeeding is the preferred choice of infant feeding. ... pressure, the date of initiation and date of being weaned off were .... at the time of delivery. The majority ...

Mixed Waste Management Facility

International Nuclear Information System (INIS)

Brummond, W.; Celeste, J.; Steenhoven, J.

1993-08-01

The DOE has developed a National Mixed Waste Strategic Plan which calls for the construction of 2 to 9 mixed waste treatment centers in the Complex in the near future. LLNL is working to establish an integrated mixed waste technology development and demonstration system facility, the Mixed Waste Management Facility (MWMF), to support the DOE National Mixed Waste Strategic Plan. The MWMF will develop, demonstrate, test, and evaluate incinerator-alternatives which will comply with regulations governing the treatment and disposal of organic mixed wastes. LLNL will provide the DOE with engineering data for design and operation of new technologies which can be implemented in their mixed waste treatment centers. MWMF will operate under real production plant conditions and process samples of real LLNL mixed waste. In addition to the destruction of organic mixed wastes, the development and demonstration will include waste feed preparation, material transport systems, aqueous treatment, off-gas treatment, and final forms, thus making it an integrated ''cradle to grave'' demonstration. Technologies from offsite as well as LLNL's will be tested and evaluated when they are ready for a pilot scale demonstration, according to the needs of the DOE

Prion infectivity detected in swine challenged with chronic wasting disease via the intracerebral or oral route

Science.gov (United States)

Chronic wasting disease (CWD) is a naturally-occurring, fatal neurodegenerative disease of North American cervids. The potential for swine to serve as a host for the agent of chronic wasting disease is unknown. In the US, feeding of ruminant by-products to ruminants is prohibited, but feeding of rum...

Production of a ruminant protein supplement by anaerobic fermentation of feedlot waste filtrate

Energy Technology Data Exchange (ETDEWEB)

Reddy, C.A.; Erdman, M.D.

1977-01-01

In studies initiated to develop simple and efficient procedures for the production of feed supplements, it was shown that the filtrate from feedlot wastes diluted with water and filtered could be fermented under anaerobic conditions by mixed rumen bacteria, Lactobacilli, or natural microflora from the feedlot wastes to produce a protein-rich feed supplement. The filtrate is low in carbohydrate and therefore supplemental carbohydrate in the form of whey, molasses, starch from potato processing wastes, or corn starch is necessary. Rigid anaerobic conditions need not be maintained nor must aseptic conditions be observed. (JSR)

Effects of crude glycerin from waste vegetable oil supplementation on feed intake, ruminal fermentation characteristics, and nitrogen utilization of goats.

Science.gov (United States)

Chanjula, Pin; Pongprayoon, Sahutaya; Kongpan, Sirichai; Cherdthong, Anusorn

2016-06-01

This experiment was evaluation of the effects of increasing concentrations of crude glycerin from waste vegetable oil (CGWVO) in diets on feed intake, digestibility, ruminal fermentation characteristics, and nitrogen balance of goats. Four crossbred male (Thai Native × Anglo Nubian) goats, with an average initial body weight (BW) of 31.5 ± 1.90 kg, were randomly assigned according to a 4 × 4 Latin square design. The dietary treatments contained 0, 2, 4, and 6 % of dietary dry matter (DM) of CGWVO. Based on this experiment, there were significantly different (P > 0.05) among treatment groups regarding DM intake and digestion coefficients of nutrients (DM, OM, CP, EE, NDF, and ADF), which goats receiving 6 % of CGWVO had lower daily DMI and nutrient intake than those fed on 0, 2, and 4 % of CGWVO. Ruminal pH, NH3-N, and blood urea nitrogen (BUN) concentration were unchanged by dietary treatments, except that for 6 % of CGWVO supplementation, NH3-N, and BUN were lower (P goats. This study was a good approach in exploiting the use of biodiesel production from waste vegetable oil for goat production.

The Effect of Soy Sauce Waste in Ration on Performance of Mojosari Duck

Directory of Open Access Journals (Sweden)

G. A. A. Larasati

2017-06-01

Full Text Available The purpose of study was to determined the effect of soy sauce waste in ration in the ration on the performance of Mojosari duck. The materials used were 240 of Mojosari which are 20 weeks olds with average body weight 1,385.0 ± 130.85 grams (CV = 9.44%. Feed ingredients used were, rice bran, soybean meal, yellow corn, fish meal, pollard and premix. The design that used was Completely Randomized Design (CRD with 4 treatments and 6 replications.The treatment applied soy sauce waste at level 5, 7,5 and 10%. The parameters observed were consumption, egg production, feed conversion. The data were analyzed by analysis of variance with F test. The results showed that soy sauce waste did not effected on performance (consumption of ration, egg production, ration conversion of Mojosari duck. The conclusion of this research is soy sauce waste be used as feed stuff of Mojosari duck ration until level 10%.

Metabolisable energy values of some non-conventional feeding ...

African Journals Online (AJOL)

A metabolism trial was designed to evaluate dietary energy values (AME, AMEn, TME, TMEn) of eight readily available non-conventional feeding ingredients viz: cassava root meal (CRM); cassava leaf meal (CLM), mango leaf meal (MLM), shrimp waste meal (SWM), full-fat soyabean (FFSB), palm oil sludge (POS), corn cob ...

Control of DWPF melter feed composition

International Nuclear Information System (INIS)

Brown, K.G.; Edwards, R.E.; Postles, R.L.; Randall, C.T.

1989-01-01

The Defense Waste Processing Facility will be used to immobilize Savannah River Site high-level waste into a stable borosilicate glass for disposal in a geologic repository. Proper control of the melter feed composition in this facility is essential to the production of glass which meets product durability constraints dictated by repository regulations and facility processing constraints dictated by melter design. A technique has been developed which utilizes glass property models to determine acceptable processing regions based on the multiple constraints imposed on the glass product and to display these regions graphically. This system along with the batch simulation of the process is being used to form the basis for the statistical process control system for the facility

The acid digestion process for radioactive waste: The radioactive waste management series. Volume II

International Nuclear Information System (INIS)

Cecille, L.; Simon, R.

1983-01-01

This volume focuses on the acid digestion process for the treatment of alpha combustible solid waste by presenting detailed performance figures for the principal sub-assemblies of the Alona pilot plant, Belgium. Experience gained from the operation of the US RADTU plant, the only other acid digestion pilot plant, is also summarized, and the performances of these two plants compared. In addition, the research and development programmes carried out or supported by the Commission of the European Communities are reviewed, and details of an alternative to acid digestion for waste contamination described. Topics considered include review of the treatment of actinides-bearing radioactive wastes; alpha waste arisings in fuel fabrication; Alona Demonstration Facility for the acid digestion process at Eurochemic Mol (Belgium); the treatment of alpha waste at Eurochemic by acid digestion-feed pretreatment and plutonium recovery; US experience with acid digestion of combustible transuranic waste; and The European Communities R and D actions on alpha waste

Glass-Ceramic Waste Forms for Uranium and Plutonium Residues Wastes - 13164

International Nuclear Information System (INIS)

Stewart, Martin W.A.; Moricca, Sam A.; Zhang, Yingjie; Day, R. Arthur; Begg, Bruce D.; Scales, Charlie R.; Maddrell, Ewan R.; Hobbs, Jeff

2013-01-01

A program of work has been undertaken to treat plutonium-residues wastes at Sellafield. These have arisen from past fuel development work and are highly variable in both physical and chemical composition. The principal radiological elements present are U and Pu, with small amounts of Th. The waste packages contain Pu in amounts that are too low to be economically recycled as fuel and too high to be disposed of as lower level Pu contaminated material. NNL and ANSTO have developed full-ceramic and glass-ceramic waste forms in which hot-isostatic pressing is used as the consolidation step to safely immobilize the waste into a form suitable for long-term disposition. We discuss development work on the glass-ceramic developed for impure waste streams, in particular the effect of variations in the waste feed chemistry glass-ceramic. The waste chemistry was categorized into actinides, impurity cations, glass formers and anions. Variations of the relative amounts of these on the properties and chemistry of the waste form were investigated and the waste form was found to be largely unaffected by these changes. This work mainly discusses the initial trials with Th and U. Later trials with larger variations and work with Pu-doped samples further confirmed the flexibility of the glass-ceramic. (authors)

Fermentation instead of animal feeding; In den Fermenter statt in den Magen des Schweins

Energy Technology Data Exchange (ETDEWEB)

Brombach, T.

2008-07-01

Since 2006, Germany has prohibited the feeding of class K3 waste food from gastronomy, canteens and the food industry to pigs. Fermentation is a creative solution. In Haid on the Schwaebische Alb mountain range, two creative waste managers developed a plant for power generation from fat and used oils. (orig.)

Anaerobic biodegradation of a petrochemical waste-water using biomass support particles

International Nuclear Information System (INIS)

Sharma, S.; Ramakrishna, C.; Desai, J.D.; Bhatt, N.M.

1994-01-01

During the anaerobic biodegradation of effluent from a dimethyl terephthalate (DMT) manufacturing plant, reduction in chemical oxygen demand (COD) degradation and biogas formation was observed after the waste-water concentration exceeded 25% of added feed COD. This condition reverted back to normal after 25-30 days when the DMT waste-water concentration in the feed was brought down to a non-toxic level. However, the above effects were observed only after the concentration of DMT waste-water reached more than 75% of added feed COD when biomass support particles (BSP) were augmented to the system. In the BSP system, a biomass concentration of up to 7000 mg/l was retained and the sludge retention time increased to >200 days compared to 2200 mg/l and 8-10 days, respectively, in the system without BSP (control). Formaldehyde in the waste-water was found to be responsible for the observed toxicity. The BSP system was found to resist formaldehyde toxicity of up to 375 mg/l as against 125 mg/l in the control system. Moreover, the BSP system recovered from the toxicity much faster (15 days) than the control (25-30 days). The advantages of the BSP system in anaerobic treatment of DMT waste-water are discussed. (orig.)

Vitrification technology for Hanford Site tank waste

International Nuclear Information System (INIS)

Weber, E.T.; Calmus, R.B.; Wilson, C.N.

1995-04-01

The US Department of Energy's (DOE) Hanford Site has an inventory of 217,000 m 3 of nuclear waste stored in 177 underground tanks. The DOE, the US Environmental Protection Agency, and the Washington State Department of Ecology have agreed that most of the Hanford Site tank waste will be immobilized by vitrification before final disposal. This will be accomplished by separating the tank waste into high- and low-level fractions. Capabilities for high-capacity vitrification are being assessed and developed for each waste fraction. This paper provides an overview of the program for selecting preferred high-level waste melter and feed processing technologies for use in Hanford Site tank waste processing

Wood chip delivery and research project at Mikkeli region

International Nuclear Information System (INIS)

Saksa, T.; Auvinen, P.

1995-01-01

In 1994, a large-scale energywood production chain was started as a co-operation project by the Mikkeli city forest office and local forestry societies. Over 60 000 m 3 (about 46 000 MWh of energy) of forest processed chips were delivered to Pursiala heat and power plant in Mikkeli. About 60 % of these chips was whole tree chips from improvement cuttings of young forest stands and the rest was logging waste chips from regeneration cutting areas. The average total delivery costs of forest processed chips after reduction of energywood and other subsidies were approximately 51 FIM/m 3 (68 FIM/MWh) for the whole tree chips and 40 FIM/m 3 (53 FIM/MWh) for logging waste chips. The delivery costs of wood chips could compete with those of fuel peat only in the most favourable cases. The resources of forest processed chips were studied on the basis of forestry plans. According to the study, there is enough raw material for permanent, large-scale delivery of forest processed chips (up to 250 000 m 3 /a) in the forests located at a distance of under 40 road kilometers from the Pursiala heat and power plant. The following project stages will involve further development of the wood chip delivery chain logistics, as well as improvement of logging and chipping equipment and methods in energywood and logging waste production. Also the effects of wood energy production on the economy and environment of the whole Mikkeli region will be studied. (author)

Biological treatment of concentrated hazardous, toxic, andradionuclide mixed wastes without dilution

Energy Technology Data Exchange (ETDEWEB)

Stringfellow, William T.; Komada, Tatsuyuki; Chang, Li-Yang

2004-06-15

Approximately 10 percent of all radioactive wastes produced in the U. S. are mixed with hazardous or toxic chemicals and therefore can not be placed in secure land disposal facilities. Mixed wastes containing hazardous organic chemicals are often incinerated, but volatile radioactive elements are released directly into the biosphere. Some mixed wastes do not currently have any identified disposal option and are stored locally awaiting new developments. Biological treatment has been proposed as a potentially safer alternative to incineration for the treatment of hazardous organic mixed wastes, since biological treatment would not release volatile radioisotopes and the residual low-level radioactive waste would no longer be restricted from land disposal. Prior studies have shown that toxicity associated with acetonitrile is a significant limiting factor for the application of biotreatment to mixed wastes and excessive dilution was required to avoid inhibition of biological treatment. In this study, we demonstrate that a novel reactor configuration, where the concentrated toxic waste is drip-fed into a complete-mix bioreactor containing a pre-concentrated active microbial population, can be used to treat a surrogate acetonitrile mixed waste stream without excessive dilution. Using a drip-feed bioreactor, we were able to treat a 90,000 mg/L acetonitrile solution to less than 0.1 mg/L final concentration using a dilution factor of only 3.4. It was determined that the acetonitrile degradation reaction was inhibited at a pH above 7.2 and that the reactor could be modeled using conventional kinetic and mass balance approaches. Using a drip-feed reactor configuration addresses a major limiting factor (toxic inhibition) for the biological treatment of toxic, hazardous, or radioactive mixed wastes and suggests that drip-feed bioreactors could be used to treat other concentrated toxic waste streams, such as chemical warfare materiel.

Utilization of agro-resources by radiation treatment -production of animal feed and mushroom from oil palm wastes

International Nuclear Information System (INIS)

Kume, Tamikazu; Matsuhashi, Shinpei; Hashimoto, Shoji

1993-01-01

The production of animal feeds and mushrooms from oil palm cellulosic wastes by radiation and fermentation has been investigated in order to utilize the agro-resources and to reduce the smoke pollution. The process is as follows: decontamination of microorganisms in fermentation media of empty fruit bunch of oil palm (EBF) by irradiation, inoculation of useful fungi, and subsequently production of proteins and edible mushrooms. The dose of 25 kGy was required for the sterilization of contaminating bacteria whereas the dose of 10 kGy was enough to eliminate the fungi. Among many kinds of fungi tested, C. cinereus and P. sajor-caju were selected as the most suitable microorganism for the fermentation of EFB. The protein content of the product increased to 13% and the crude fiber content decreased to 20% after 30 days of incubation with C. cinereus at 30 o C in solid state fermentation. P. sajor-caju was suitable for the mushroom production on EFB with rice bran. (author)

Effects of the feeding ratio of food waste on fed-batch aerobic composting and its microbial community.

Science.gov (United States)

Wang, Xiaojun; Pan, Songqing; Zhang, Zhaoji; Lin, Xiangyu; Zhang, Yuzhen; Chen, Shaohua

2017-01-01

To determine the suitable feeding ratio for fed-batch aerobic composting, four fermenters were operated by adding 0%, 5%, 10% or 15% of food waste every day. The results showed that the 5% and 10% treatments were able to maintain continuous thermophilic conditions, while the 15% treatment performed badly in regard to composting temperature, which was probably due to the negative effects of excessive moisture on microbial activity. As composting proceeded, both the 5% and the 10% treatments reached maturity and achieved weight losses of approximately 65%. High-throughput sequencing results indicated that Firmicutes, Proteobacteria, Bacteroidetes and Actinobacteria were the dominant phyla of the community structure. The communities sampled at the thermophilic phases had high similarity and relatively low diversity, while species diversity increased in the maturity phase. This study was devoted to optimizing the fed-batch composting process and assessing bacterial communities, both of which were supplied as a reference for practical application. Copyright © 2016 Elsevier Ltd. All rights reserved.

Suggested instructions for the completion of delivery commitment schedules

International Nuclear Information System (INIS)

Vance, S.A.

1992-01-01

This presentation discusses the Delivery Commitment Schedule form contained in Appendix C of the Standard Contract for Disposal of Spent Nuclear Fuel and/or High-Level Radioactive Waste (the Standard Contract). In particular, the presentation describes some preliminary suggested instructions for completing the form in a manner that may aid the US Department of Energy (DOE) in the development of the Federal Waste Management System (FWMS)

Modelling Waste Output from Trout Farms

DEFF Research Database (Denmark)

Frier, J. O.; From, J.; Larsen, Torben

1995-01-01

to calculate waste discharge from existing and planned aquaculture activities. A special purpose is simulating outcome of waste water treatment and altered feeding programmes. Different submodels must be applied for P, N, and organics, as well as for the different phases of food and waste treatment. Altogether...... this calls for an array of co-operating submodels for a sufficient coverage of the options. In all the required fields there is some scientific background for numerical model approaches, and some submodels have been proposed. Because of its multidisciplinary character a synthesized approach is still lacking...

Effect of feeding cassava bioethanol waste on nutrient intake, digestibility, and rumen fermentation in growing goats.

Science.gov (United States)

Cherdthong, Anusorn; Pornjantuek, Boonserm; Wachirapakorn, Chalong

2016-10-01

This experiment was conducted to investigate the effects of various levels of cassava bioethanol waste (CBW) on nutrient intake, digestibility, rumen fermentation, and blood metabolites in growing goats. Twelve crossbred, male (Thai Native × Anglo Nubian) growing goats with initial body weight (BW) of 20±3 kg were randomly assigned according to a completely randomized design (CRD). The dietary treatments were total mixed ration (TMR) containing various levels of CBW at 0, 10, and 20 % dry matter (DM). CBW contained crude protein (CP), neutral detergent fiber (NDF), acid detergent fiber (ADF), and acid detergent lignin (ADL) at 11, 69, 47, and 23 % DM, respectively. The TMR diets were offered ad libitum and contained CP at 15 % DM. Inclusion of CBW at 10 % DM in TMR did not alter feed intake (g DM and g/kg BW(0.75)) and CP intake when compared to the control fed group (0 % CBW). Total OM intake was lower in the 20 % CBW group than in the others (P  0.05) whereas when 20 % CBW was incorporated to diet, intermediate digestibility coefficients were decreased. Average ruminal pH values ranged from 6-7. Rumen NH3-N and PUN concentration at 0, 3, and 6 h post-feeding were not significantly different among treatments (P > 0.05). Thus, inclusion of 10 % CBW in TMR diets does not adversely affect nutrient intake, digestibility, rumen fermentation, and blood metabolite in fattening goats, and CBW may be effectively used as an alternative roughage source in the diets of goats.

Dose imprecision and resistance: free-choice medicated feeds in industrial food animal production in the United States.

Science.gov (United States)

Love, David C; Davis, Meghan F; Bassett, Anna; Gunther, Andrew; Nachman, Keeve E

2011-03-01

Industrial food animal production employs many of the same antibiotics or classes of antibiotics that are used in human medicine. These drugs can be administered to food animals in the form of free-choice medicated feeds (FCMF), where animals choose how much feed to consume. Routine administration of these drugs to livestock selects for microorganisms that are resistant to medications critical to the treatment of clinical infections in humans. In this commentary, we discuss the history of medicated feeds, the nature of FCMF use with regard to dose delivery, and U.S. policies that address antimicrobial drug use in food animals. FCMF makes delivering a predictable, accurate, and intended dose difficult. Overdosing can lead to animal toxicity; underdosing or inconsistent dosing can result in a failure to resolve animal diseases and in the development of antimicrobial-resistant microorganisms. The delivery of antibiotics to food animals for reasons other than the treatment of clinically diagnosed disease, especially via free-choice feeding methods, should be reconsidered.

Treatment of Mixed Wastes via Fixed Bed Gasification

Energy Technology Data Exchange (ETDEWEB)

None

1998-10-28

This report outlines the details of research performed under USDOE Cooperative Agreement DE-FC21-96MC33258 to evaluate the ChemChar hazardous waste system for the destruction of mixed wastes, defined as those that contain both RCRA-regulated haz- ardous constituents and radionuclides. The ChemChar gasification system uses a granular carbonaceous char matrix to immobilize wastes and feed them into the gasifier. In the gasifier wastes are subjected to high temperature reducing conditions, which destroy the organic constituents and immobilize radionuclides on the regenerated char. Only about 10 percent of the char is consumed on each pass through the gasifier, and the regenerated char can be used to treat additional wastes. When tested on a 4-inch diameter scale with a continuous feed unit as part of this research, the ChemChar gasification system was found to be effective in destroying RCRA surrogate organic wastes (chlorobenzene, dichloroben- zene, and napht.halene) while retaining on the char RCRA heavy metals (chromium, nickel, lead, and cadmium) as well as a fission product surrogate (cesium) and a plutonium surrogate (cerium). No generation of harmful byproducts was observed. This report describes the design and testing of the ChemChar gasification system and gives the operating procedures to be followed in using the system safely and effectively for mixed waste treatment.

Benchmarking of DFLAW Solid Secondary Wastes and Processes with UK/Europe Counterparts

Energy Technology Data Exchange (ETDEWEB)

Brown, Elvie E. [Hanford Site (HNF), Richland, WA (United States); Swanberg, David J. [Hanford Site (HNF), Richland, WA (United States); Surman, J. [Hanford Site (HNF), Richland, WA (United States); Kay, R. [Hanford Site (HNF), Richland, WA (United States); Williams, K. [Hanford Site (HNF), Richland, WA (United States)

2017-05-08

This report provides information and background on UK solid wastes and waste processes that are similar to those which will be generated by the Direct-Feed Low Activity Waste (DFLAW) facilities at Hanford. The aim is to further improve the design case for stabilizing and immobilizing of solid secondary wastes, establish international benchmarking and review possibilities for innovation.

Effects of feeding level and feeding frequency on growth, feed efficiency and nitrogen and phosphorus loss in seabass (Lates calcarifer Bloch fed diets with defatted soybean meal partially replacing fishmeal

Directory of Open Access Journals (Sweden)

Srisook, S.

2007-05-01

Full Text Available Satun Coastal Fisheries Research and Development Center, Muang, Satun 3Feeding management is crucial for feed efficiency, nutrient utilization, growth of cultured aquatic species and the amount of organic waste produced. This study aimed at investigating effects of two levels offeeding at two feeding frequencies on growth performance, feed efficiency and nitrogen and phosphorus loss in Asian seabass when fed diets with defatted soybean meal (SBM replacing fish meal. Three diets were formulated to contain defatted SBM to replace fish meal at 0, 10 and 20% of fish meal protein. Each diet wasgiven to the fish at either 4% of body weight (BW or to satiation. At each feeding level, the fish were fed at two feeding frequencies, once and twice daily. Fish with an average initial weight of 2.04±0.06 g/fish werereared for twelve weeks in the flow through system. Growth of fish reduced with an increasing amount of defatted SBM incorporated in diets as observed in other carnivorous species. Within groups of fish fed thesame diet, different growth performance and feed efficiency differed due to both feeding level and frequency. Weight gain of fish that were fed diet with defatted SBM replacing 10% of fish meal protein (diet 2until satiation was not significantly different from fish fed fish meal based diet at 4% BW. Furthermore, feeding fish the former diet twice daily resulted in an improvement of FCR, PER and PPV of fish to those ofthe fish fed fish meal based diet at satiation twice daily. Nitrogen and phosphorus loss was affected by diet, feeding level and frequency. Fish fed diet 2 until satiation twice daily lost nitrogen and phosphorus in theamount similar to that of fish fed fish meal based diet until satiation.

Radioactive wastes transport. A safety logic

International Nuclear Information System (INIS)

2005-01-01

The safety principle which applies to transport operations of radioactive wastes obeys to a very strict regulation. For the conditioning of wastes in package, the organisation of shipments and the qualification of carriers, the ANDRA, the French national agency of radioactive wastes, has implemented a rigorous policy based on the respect of a quality procedure and on the mastery of delivery fluxes. This brochure presents in a simple, illustrated and detailed manner the different steps of these transports. (J.S.)

Process and device for liquid organic waste processing by sulfuric mineralization

International Nuclear Information System (INIS)

Aspart, A.; Gillet, B.; Lours, S.; Guillaume, B.

1990-01-01

In a chemical reactor containing sulfuric acid are introduced the liquid waste and nitric acid at a controlled flow rate for carbonization of the waste and oxidation of carbon on sulfur dioxide, formed during carbonization, regenerating simultaneously sulfuric acid. Optical density of the liquid is monitored to stop liquid waste feeding above a set-point. The liquid waste can be an organic solvent such as TBP [fr

The role of the nurse in support of breast feeding.

Science.gov (United States)

Auerbach, K G

1979-05-01

The nurse can provide information about, and support of, breast feeding. The prenatal nurse can inform the mother of the advantages of breast feeding to herself and her baby. The labour and delivery nurse can aid the mother in her first contact with the baby and reassure the mother who has a Caesarean birth, or a premature or sick infant, that she too can nurse. The postpartum nurse can help breast feeding to continue by providing frequent maternal-infant contact during the mother's hospital stay. The nursery nurse supports breast feeding by refraining from giving the baby other fluids. The paediatric nurse continues the helping pattern by reinforcing the statements and actions of others which will further impress the mother with the appropriateness of her infant feeding method. Mothers need to be informed about infant feeding options in order to make a knowledgeable choice based on awareness of alternatives. The nurse's role in support of breast feeding varies with the time and place where patient care is provided. In each setting, however, the nurse plays a significant role in helping the mother to begin breast feeding and to enjoy it, at the same time providing her infant with optimum nutrition for his early growth and development.

From environmental nuisance to environmental opportunity: housefly larvae convert waste to livestock feed

NARCIS (Netherlands)

Zanten, van H.H.E.; Mollenhorst, H.; Oonincx, D.G.A.B.; Bikker, P.; Meerburg, B.G.; Boer, de I.J.M.

2015-01-01

The livestock sector is in urgent need for more sustainable feed sources, because of the increased demand for animal-source food and the already high environmental costs associated with it. Recent developments indicate environmental benefits of rearing insects for livestock feed, suggesting that

Hanford High-Level Waste Vitrification Program at the Pacific Northwest National Laboratory: technology development - annotated bibliography

International Nuclear Information System (INIS)

Larson, D.E.

1996-09-01

This report provides a collection of annotated bibliographies for documents prepared under the Hanford High-Level Waste Vitrification (Plant) Program. The bibliographies are for documents from Fiscal Year 1983 through Fiscal Year 1995, and include work conducted at or under the direction of the Pacific Northwest National Laboratory. The bibliographies included focus on the technology developed over the specified time period for vitrifying Hanford pretreated high-level waste. The following subject areas are included: General Documentation; Program Documentation; High-Level Waste Characterization; Glass Formulation and Characterization; Feed Preparation; Radioactive Feed Preparation and Glass Properties Testing; Full-Scale Feed Preparation Testing; Equipment Materials Testing; Melter Performance Assessment and Evaluations; Liquid-Fed Ceramic Melter; Cold Crucible Melter; Stirred Melter; High-Temperature Melter; Melter Off-Gas Treatment; Vitrification Waste Treatment; Process, Product Control and Modeling; Analytical; and Canister Closure, Decontamination, and Handling