Environmental Assessment for Hazardous Waste Staging Facility, Pantex Plant, Amarillo, Texas

International Nuclear Information System (INIS)

1993-06-01

This Environmental Assessment (EA) has been prepared pursuant to the implementing regulations to the National Environmental Policy Act (NEPA), which require federal agencies to assess the environmental impacts of a proposed action to determine whether that action requires the preparation of an Environmental Impact Statement (EIS) or if a Finding of No Significant Impact (FONSI) can be issued. The Pantex Plant does not possess permanent containerized waste staging facilities with integral secondary containment or freeze protection. Additional deficiencies associated with some existing staging facilities include: no protection from precipitation running across the staging pads; lack of protection against weathering; and facility foundations not capable of containing leaks, spills or accumulated precipitation. These shortcomings have raised concerns with respect to requirements under Section 3001 of the Resource Conservation and Recovery Act (RCRA). Deficiencies for these waste staging areas were also cited by a government audit team (Tiger Team) as Action Items. The provision for the staging of hazardous, mixed, and low level waste is part of the no-action altemative in the Programmatic Environmental Impact Statement for the integrated ER/WM program. Construction of this proposed project will not prejudice whether or not this integration will occur, or how

Construction of mixed waste storage RCRA facilities, Buildings 7668 and 7669: Environmental assessment

International Nuclear Information System (INIS)

1994-04-01

The Department of Energy has prepared an environmental assessment, DOE/EA-0820, to assess the potential environmental impacts of constructing and operating two mixed waste Resource Conservation and Recovery Act (RCRA) storage facilities. The new facilities would be located inside and immediately west of the security-fenced area of the Oak Ridge National Laboratory Hazardous Waste Management Area in Melton Valley, Tennessee. Based on the analyses in the environmental assessment, the Department has determined that the proposed action does not constitute a major Federal action significantly affecting the quality of the human environment within the meaning of the National Environmental Policy Act of 1969. Therefore, the preparation of an environmental impact statement is not required, and the Department is issuing this finding of no significant impact

Environmental assessment of waste incineration and alternatives; Miljoevurdering af affaldsforbraending og alternativer

Energy Technology Data Exchange (ETDEWEB)

Moeller, J.; Fruergaard, T.; Riber, C.; Astrup, T.; Hoejlund Christensen, T.

2008-06-15

Life cycle environmental assessment of waste combustion and alternatives were made using the LCA model EASEWASTE. Possible environmental effects for nine effect categories and the resource consumption of fossil fuels through treating 1 ton combustible waste were defined for several waste systems, including waste-only incineration, co-combustion in a fossil-fueled cogeneration plant, and combined biogas and compost production from household waste. The main conclusions of the analyses are: 1) with an optimum location, i.e. in the vicinity to a coal-fueled cogeneration plant, waste-only incineration, co-combustion , and combined biogas and compost production are all equal environmentally viable alternatives . 2) Regarding potential toxic impacts in the area of a coal-fueled cogeneration plant, waste-only incineration and combined biogas and compost production will result in slightly less net emissions compared to co-combustion because of better flue gas cleaning of heavy metals in incinerators than in power plants. 3) Siting the incinerator in a decentralized natural gas cogeneration area, co-combustion in a cogeneration plant is a better solution. 4) Combined biogas and compost production and waste-only combustion are environmentally equal treatments in all power plant areas. (ln)

Environmental impact assessment of decommissioning treatment about radioactive model plant waste ore storage site

International Nuclear Information System (INIS)

Bei Xinyu

2012-01-01

Aiming at decommissioning treatment project of radioactive model plant waste ore storage site, based on the detailed investigations of source terms and project description, systematic environmental impacts have been identified. The environmental impacts both during decommissioning treatment, radioactive waste transportation and after treatment are assessed. Some specific environmental protection measures are proposed so as to minimize the adverse environmental impacts. (author)

Quality assurance program for environmental assessment of Savannah River Plant waste sites: Environmental information document

International Nuclear Information System (INIS)

Looney, B.B.; King, C.M.; Stephenson, D.E.

1987-03-01

Forty-eight locations were identified that received a variety of radioactive and nonradioactive constituents during the past 35 years including surface impoundments and shallow land burial facilities. Detailed environmental assessments of existing waste disposal areas, as well as new waste disposal techniques and disposition of tritiated water, were completed to air in an evaluation of the low level, mixed and hazardous waste management activities. These assessments result in estimation of risk, or residual risk, posed by each disposal area to various receptors as a function of waste management alternative. For example, at existing waste sites, the closure actions evaluated were waste removal and closure, no waste removal and closure, and no action; several pathways/receptors were considered, including groundwater to river, groundwater to well, atmospheric transport, occupational exposure, direct exposure, and contamination followed by ingestion of crops and meat. Modeling of chemical transport in a variety of media was an integral part of the assessment process. The quality of the models used and the application of these models were assured by an explicit quality assurance program

Guidelines for comparative assessment of the environmental impacts of wastes from electricity generation systems. A framework for the assessment and comparison of environmental impacts

International Nuclear Information System (INIS)

1995-02-01

The report describes the initial phase of a project intended to provide guidance to those concerned with environmental aspects of solid and hazardous waste management in electrical energy production systems. The focus is on describing a methodology for assessing and comparing the environmental impact arising from these wastes, and thereby to provide an input to overall electrical generation comparison projects, such as DECADES. The structure of the report is as follows: after considering a range of electrical energy production systems with an outline discussion of the waste streams produced in each case, the relevant treatment technologies and disposal options are reviewed. Then the elements of the framework for comparative assessment proposed in this report are described. The types of environmental impact, environmental protection criteria and indicators or end-points to measure the impact, the way in which such impacts can be quantitatively assessed and compared are discussed. 59 refs, figs and tabs

Long-term environmental assessment of waste from PyroGreen system

International Nuclear Information System (INIS)

Ju, Heejae; Hahm, Inhye; Sohn, Sungjune; Hwang, Il-Soon

2016-01-01

We have conducted a long-term environmental assessment of a geological repository for Intermediate Level Wastes (ILW) arising from PyroGreen processes that has been developed to decontaminate all HLW from the pyrochemical partitioning of spent nuclear fuels (SNF). PyroGreen process has been designed so that final ILW can meet conservative acceptance criteria such as one established for the Waste Isolation Pilot Plant (WIPP) in U.S.A. The nuclide inventory of final vitrified PyroGreen waste is calculated using ORIGEN 2.1 based on the design decontamination factor of PyroGreen processes applied to 18,171 metric tons of PWR SNF with 45 GWD/MTU burnup. Using GoldSim model, the environmental impact of ILW upon geological disposal at an intermediate depth. Among radioactive nuclides, Ra 226 , Rn 222 and Sn 126 are identified as key contributors to radiological dose for general public. The environmental impact of PyroGreen wastes satisfies the Korean dose limit of 0.1 mSv/year with sufficiently high margin. Sensitivity studies have shown that the predicted dose can vary significantly by distribution coefficient of Ra 226 and Rn 222 , solubility limit of Se 79 . (authors)

Long-term environmental assessment of waste from PyroGreen system

Energy Technology Data Exchange (ETDEWEB)

Ju, Heejae; Hahm, Inhye; Sohn, Sungjune; Hwang, Il-Soon [Seoul National University, Gwanak-ro, Gwanak-gu, Seoul, 151-742 (Korea, Republic of)

2016-07-01

We have conducted a long-term environmental assessment of a geological repository for Intermediate Level Wastes (ILW) arising from PyroGreen processes that has been developed to decontaminate all HLW from the pyrochemical partitioning of spent nuclear fuels (SNF). PyroGreen process has been designed so that final ILW can meet conservative acceptance criteria such as one established for the Waste Isolation Pilot Plant (WIPP) in U.S.A. The nuclide inventory of final vitrified PyroGreen waste is calculated using ORIGEN 2.1 based on the design decontamination factor of PyroGreen processes applied to 18,171 metric tons of PWR SNF with 45 GWD/MTU burnup. Using GoldSim model, the environmental impact of ILW upon geological disposal at an intermediate depth. Among radioactive nuclides, Ra{sup 226}, Rn{sup 222} and Sn{sup 126} are identified as key contributors to radiological dose for general public. The environmental impact of PyroGreen wastes satisfies the Korean dose limit of 0.1 mSv/year with sufficiently high margin. Sensitivity studies have shown that the predicted dose can vary significantly by distribution coefficient of Ra{sup 226} and Rn{sup 222}, solubility limit of Se{sup 79}. (authors)

Environmental assessment of low-organic waste landfill scenarios by means of life-cycle assessment modelling (EASEWASTE)

DEFF Research Database (Denmark)

Manfredi, Simone; Christensen, Thomas Højlund; Scharff, H.

2010-01-01

for in the life-cycle impact assessment calculation, the small gas generation in low-organic waste landfills reduced the actual potential for energy generation and therefore the environmental savings obtained were reduced proportionally. Groundwater pollution from input of leachate was also evaluated and the WHO......The environmental performance of two low-organic waste landfill scenarios ('low-organic-energy' and 'low-organic-flare') was developed and compared with two household waste landfill scenarios ('household-energy' and 'household-flare') by means of LCA-modelling. The LCA-modelling was made for 1...

Environmental exposure assessment framework for nanoparticles in solid waste

Science.gov (United States)

Boldrin, Alessio; Hansen, Steffen Foss; Baun, Anders; Hartmann, Nanna Isabella Bloch; Astrup, Thomas Fruergaard

2014-06-01

Information related to the potential environmental exposure of engineered nanomaterials (ENMs) in the solid waste management phase is extremely scarce. In this paper, we define nanowaste as separately collected or collectable waste materials which are or contain ENMs, and we present a five-step framework for the systematic assessment of ENM exposure during nanowaste management. The framework includes deriving EOL nanoproducts and evaluating the physicochemical properties of the nanostructure, matrix properties and nanowaste treatment processes as well as transformation processes and environment releases, eventually leading to a final assessment of potential ENM exposure. The proposed framework was applied to three selected nanoproducts: nanosilver polyester textile, nanoTiO2 sunscreen lotion and carbon nanotube tennis racquets. We found that the potential global environmental exposure of ENMs associated with these three products was an estimated 0.5-143 Mg/year, which can also be characterised qualitatively as medium, medium, low, respectively. Specific challenges remain and should be subject to further research: (1) analytical techniques for the characterisation of nanowaste and its transformation during waste treatment processes, (2) mechanisms for the release of ENMs, (3) the quantification of nanowaste amounts at the regional scale, (4) a definition of acceptable limit values for exposure to ENMs from nanowaste and (5) the reporting of nanowaste generation data.

Comparative assessment of the environmental impact of wastes from electricity generation systems

International Nuclear Information System (INIS)

Torres, C.; Smith, G.M.; Linsley, G.; Hossain, S.

1994-01-01

The paper describes an outline methodology for assessing and comparing the environmental impact arising from management of the wastes from nuclear and other electricity generation systems. The assessment framework is applicable to wastes from all generation systems, including nuclear, fossil and renewable fuel systems, and can also be applied to the management of mixed hazardous waste. The major energy technologies in terms of waste production can be classified according to three major categories of fuels: fossil, nuclear and renewable. The emphasis in this description is on nuclear utility low-level and mixed wastes and waste streams. The methodology may be used to support the project on Data Bases and Methodologies for Comparative Assessment of Different Energy Sources for Electricity Generation (DECADES project, (2)) which is being developed by the International Atomic Energy Agency in collaboration with other international agencies. The DECADES project has the overall objective to improve the abilities for comparative assessment of energy chains for electricity generation. The objective of a methodology such as that described here is to ensure that waste management aspects are included effectively in comparative assessments of energy systems. This paper discusses the waste strams arising from nuclear power plants

Life cycle assessment to compare the environmental impact of seven contemporary food waste management systems.

Science.gov (United States)

Edwards, Joel; Othman, Maazuza; Crossin, Enda; Burn, Stewart

2018-01-01

Municipal food waste (FW) represents 35-45% of household residual waste in Australia, with the nation generating 1.6Tg annually. It is estimated that 91% of this FW ends up in landfill. This study used life cycle assessment to determine and compare the environmental impact of seven contemporary FW management systems for two real-life jurisdictions; incorporating the complete waste service and expanding the system to include inert and garden waste. Although, no system exhibited a best ranking across all impact categories, FW digestion based systems were all revealed to have a lower global warming potential than composting and landfilling systems. Mechanical biological treatment, anaerobic co-digestion, and home composting all demonstrated the lowest environmental impacts for two or more of the environmental impact categories assessed. The assessment included market and technological specific variables and uncertainties providing a framework for robust decision making at a municipality level. Crown Copyright © 2017. Published by Elsevier Ltd. All rights reserved.

ENVIRONMENTAL RESEARCH BRIEF: WASTE MINIMIZATION ASSESSMENT FOR A MANUFACTURER OF PRINTED PLASTIC BAGS

Science.gov (United States)

The U.S. Environmental Protection Agency (EPA) has funded a pilot project to assist small- and medium-size manufacturers who want to minimize their generation of hazardous waste but who lack the expertise to do so. Waste Minimization Assessment Centers (WMACs) were established ...

Pollution prevention and waste minimization opportunity assessment in environmental restoration

International Nuclear Information System (INIS)

Roybal, J.A.; Willison, C.P.

1997-01-01

The Environmental Restoration (ER) Project at Sandia National Laboratories implicitly subscribed to the philosophy of pollution prevention and waste minimization. As a result of a Department of Energy (DOE) offer, Pollution Prevention Opportunity Assessments (PPOA) were conducted at two ER sites and a decontamination and Demolition (D and D) site. The purpose of one of the PPOAs was to identify pollution prevention (P2) opportunities during environmental remediation at the Classified Waste Landfill located at Sandia National Laboratories, New Mexico (SNL/NM). The remediation activities at this site are scheduled to begin in the fall of 1997. The PPOA included presentations by the team members, a tour of the site, and a brainstorming session to list the waste streams, identify P2 opportunities and rank them in order of priority. Twenty-five P2 opportunities were identified during the brainstorming session of which twenty-two opportunities were selected for further investigation. Those twenty-two opportunities are discussed in this paper. A cost benefit analysis was performed for each P2 opportunity based on the estimated waste volume, feasibility, and cost. Pollution Prevention by Design (P2D) was incorporated into the PPOA to introduce waste minimization techniques that can be used during the planning phase of restoration projects

Waste management in the Irkutsk Region, Siberia, Russia: Environmental assessment of current practice focusing on landfilling

DEFF Research Database (Denmark)

Starostina, Vlada; Damgaard, Anders; Rechberger, Helmut

2014-01-01

The municipal waste management system of the region of Irkutsk is described and a life cycle assessment (LCA) performed to assess the environmental performance of the system. Annually about 500 000 tons of waste are managed. The waste originates from three sources: household waste (27%), commercial...... waste (23%) and office & institutional waste (44%). Other waste of unknown composition constitutes 6%. Only 3% of the waste is recycled; 97% of the municipal waste is disposed of at the old Alexandrovsky landfill. The environmental impact from the current system is dominated by the landfill, which has...... no gas or leachate collection system. The global warming contribution is due to the emission of methane of the order of 420 000 tons CO2-equivalents per year. Collection and transport of the waste are insignificant compared with impacts from the landfill. As the old landfill runs out of capacity in a few...

Environmental assessment of solid waste landfilling technologies by means of LCA-modeling.

Science.gov (United States)

Manfredi, Simone; Christensen, Thomas H

2009-01-01

By using life cycle assessment (LCA) modeling, this paper compares the environmental performance of six landfilling technologies (open dump, conventional landfill with flares, conventional landfill with energy recovery, standard bioreactor landfill, flushing bioreactor landfill and semi-aerobic landfill) and assesses the influence of the active operations practiced on these performances. The environmental assessments have been performed by means of the LCA-based tool EASEWASTE, whereby the functional unit utilized for the LCA is "landfilling of 1ton of wet household waste in a 10m deep landfill for 100 years". The assessment criteria include standard categories (global warming, nutrient enrichment, ozone depletion, photo-chemical ozone formation and acidification), toxicity-related categories (human toxicity and ecotoxicity) and impact on spoiled groundwater resources. Results demonstrate that it is crucially important to ensure the highest collection efficiency of landfill gas and leachate since a poor capture compromises the overall environmental performance. Once gas and leachate are collected and treated, the potential impacts in the standard environmental categories and on spoiled groundwater resources significantly decrease, although at the same time specific emissions from gas treatment lead to increased impact potentials in the toxicity-related categories. Gas utilization for energy recovery leads to saved emissions and avoided impact potentials in several environmental categories. Measures should be taken to prevent leachate infiltration to groundwater and it is essential to collect and treat the generated leachate. The bioreactor technologies recirculate the collected leachate to enhance the waste degradation process. This allows the gas collection period to be reduced from 40 to 15 years, although it does not lead to noticeable environmental benefits when considering a 100 years LCA-perspective. In order to more comprehensively understand the influence

Environmental and economic assessment methods for waste management decision-support: possibilities and limitations.

Science.gov (United States)

Finnveden, Göran; Björklund, Anna; Moberg, Asa; Ekvall, Tomas

2007-06-01

A large number of methods and approaches that can be used for supporting waste management decisions at different levels in society have been developed. In this paper an overview of methods is provided and preliminary guidelines for the choice of methods are presented. The methods introduced include: Environmental Impact Assessment, Strategic Environmental Assessment, Life Cycle Assessment, Cost-Benefit Analysis, Cost-effectiveness Analysis, Life-cycle Costing, Risk Assessment, Material Flow Accounting, Substance Flow Analysis, Energy Analysis, Exergy Analysis, Entropy Analysis, Environmental Management Systems, and Environmental Auditing. The characteristics used are the types of impacts included, the objects under study and whether the method is procedural or analytical. The different methods can be described as systems analysis methods. Waste management systems thinking is receiving increasing attention. This is, for example, evidenced by the suggested thematic strategy on waste by the European Commission where life-cycle analysis and life-cycle thinking get prominent positions. Indeed, life-cycle analyses have been shown to provide policy-relevant and consistent results. However, it is also clear that the studies will always be open to criticism since they are simplifications of reality and include uncertainties. This is something all systems analysis methods have in common. Assumptions can be challenged and it may be difficult to generalize from case studies to policies. This suggests that if decisions are going to be made, they are likely to be made on a less than perfect basis.

Environmental assessment methodologies for sea dumping of radioactive wastes

International Nuclear Information System (INIS)

1983-09-01

The IAEA and the IMO, in cooperation with the United Nations Environment Programme (UNEP), jointly convened a Technical Committee to provide guidance to national authorities. This document contains the results of the Technical Committee Meeting in Vienna, August - September 1982 and constitutes guidance to the Contracting Parties to the LDC Convention on the nature and content of the environmental assessment required for permit applications for sea dumping of radioactive wastes

Environmental assessment of alternative municipal solid waste management strategies. A Spanish case study.

Science.gov (United States)

Bovea, M D; Ibáñez-Forés, V; Gallardo, A; Colomer-Mendoza, F J

2010-11-01

The aim of this study is to compare, from an environmental point of view, different alternatives for the management of municipal solid waste generated in the town of Castellón de la Plana (Spain). This town currently produces 207 ton of waste per day and the waste management system employed today involves the collection of paper/cardboard, glass and light packaging from materials banks and of rest waste at street-side containers. The proposed alternative scenarios were based on a combination of the following elements: selective collection targets to be accomplished by the year 2015 as specified in the Spanish National Waste Plan (assuming they are reached to an extent of 50% and 100%), different collection models implemented nationally, and diverse treatments of both the separated biodegradable fraction and the rest waste to be disposed of on landfills. This resulted in 24 scenarios, whose environmental behaviour was studied by applying the life cycle assessment methodology. In accordance with the ISO 14040-44 (2006) standard, an inventory model was developed for the following stages of the waste management life cycle: pre-collection (bags and containers), collection, transport, pre-treatment (waste separation) and treatment/disposal (recycling, composting, biogasification+composting, landfill with/without energy recovery). Environmental indicators were obtained for different impact categories, which made it possible to identify the key variables in the waste management system and the scenario that offers the best environmental behaviour. Finally, a sensitivity analysis was used to test some of the assumptions made in the initial life cycle inventory model. Copyright © 2010 Elsevier Ltd. All rights reserved.

Strategic environmental assessment policy integration model for solid waste management in Malaysia

International Nuclear Information System (INIS)

Victor, Dennis; Agamuthu, P.

2013-01-01

Highlights: • We identified policy drivers of SEA in solid waste policy planning. • The SEA primary policy drivers are benefits, barriers and enablers need. • The SEA sub-drivers are environmental attitude and environmental awareness. • Optimal SEA policy integration requires public participation and capacity building. • SEA integration should be a long-term sustainable policy strategy for SWM. -- Abstract: This paper examines the strategic environmental assessment (SEA) systemic policy drivers for solid waste management (SWM) policies, plans and programmes (PPP) in Malaysia. Solid waste generation in Malaysia has been increasing drastically from 9.0 million tonnes in 2000 to an expected 15.6 million tonnes in 2020. This projected rate of solid waste generation is expected to burden the country's environmental and water quality resources. The key problem the study frames is the lack of environmental integration in the SWM process which is only conducted during the environmental impact assessments (EIA) stage of SWM facilities. The purpose of this study is to expand the SEA subject knowledge by validating a behaviour based theoretical framework and identifying key policy drivers that influence the integration of SEA in SWM policy planning. The study methodology utilized a confirmatory covariance based structural equation modelling approach to validate the proposed theoretical model based on the policy makers/implementers interview questionnaire data collection. The study findings indicate five latent SEA policy drivers which were named policy knowledge, environmental attitude, perceived benefits, perceived barriers and perceived enablers. The study has conceptualized and tested a SEA policy model which indicates that SEA integration behaviour is influenced directly by three main drivers (perception of benefits, perception of barriers and perception of enablers) and influenced indirectly by two sub-drivers environmental attitude and environmental knowledge

Environmental and Economic Assessment of Swedish Municipal Solid Waste Management in a Systems Perspective

International Nuclear Information System (INIS)

Eriksson, Ola

2003-01-01

strategic planning, decisions about larger investments and education in universities and within organisations. Systems analysis and models may be used in pre-planning procedures. A potential is a more general application (Technology Assessment) in predominantly waste- and biofuel based energy processes, but also for assessment of new technical components in a systems perspective. The methodology and systems approach developed within the systems analysis has here been transformed to an assessment of environmental, economic and technical performance of technical systems in a broad sense

Environmental and Economic Assessment of Swedish Municipal Solid Waste Management in a Systems Perspective

Energy Technology Data Exchange (ETDEWEB)

Eriksson, Ola

2003-04-01

strategic planning, decisions about larger investments and education in universities and within organisations. Systems analysis and models may be used in pre-planning procedures. A potential is a more general application (Technology Assessment) in predominantly waste- and biofuel based energy processes, but also for assessment of new technical components in a systems perspective. The methodology and systems approach developed within the systems analysis has here been transformed to an assessment of environmental, economic and technical performance of technical systems in a broad sense.

MKB and SMB in the Northern countries[Environmental impact assessment; Strategic environmental assessment; Radiactive waste disporal]; MKB och SMB i Norden

Energy Technology Data Exchange (ETDEWEB)

Broden, K. [Studsvik RadWaste AB (Sweden); Andersson, K. [Krinta konsult (Sweden)

2001-12-01

A meeting on Environmental Impact Assessment and Strategic Environmental Assessment has been held in Turku, Finland, August 22-24 2001. It was held within the framework of two NKS projects: SOS-3 (Radioactive waste) and SOS- 1 (Risk assessment and strategies for safety). The meeting included presenta- tions, discussions and a study visit to the final repository for low- and intermedi- ate level radioactive waste and the intermediate storage for spent nuclear fuel at Olkiluoto. Abstract in Danish: Inom ramen for NKS-projekten SOS-3 (Avfall) och SOS-1 (Riskvaardering och strategi for saakerhet) har ett seminarium om miljokonsekvensbeskrivningar och strategisk miljokonsekvensbedomning haallits i Aabo 22-24 augusti, 2001. Seminariet omfattade foredrag, diskussioner samt en studieresa till Olkoluoto daar besok gjordes till mellanlagret for anvaant braansle och till slutforvaret for laag- och medelaktivt avfall. Under forutsaattning att styrelsen for NKS samtycker kommer ett nytt MKB- seminarium att haallas i Osthammar 2002. (au)

Hazardous waste database: Waste management policy implications for the US Department of Energy's Environmental Restoration and Waste Management Programmatic Environmental Impact Statement

International Nuclear Information System (INIS)

Lazaro, M.A.; Policastro, A.J.; Antonopoulos, A.A.; Hartmann, H.M.; Koebnick, B.; Dovel, M.; Stoll, P.W.

1994-01-01

The hazardous waste risk assessment modeling (HaWRAM) database is being developed to analyze the risk from treatment technology operations and potential transportation accidents associated with the hazardous waste management alternatives. These alternatives are being assessed in the Department of Energy's Environmental Restoration and Waste Management Programmatic Environmental Impact Statement (EM PEIS). To support the risk analysis, the current database contains complexwide detailed information on hazardous waste shipments from 45 Department of Energy installations during FY 1992. The database is currently being supplemented with newly acquired data. This enhancement will improve database information on operational hazardous waste generation rates, and the level and type of current on-site treatment at Department of Energy installations

Life cycle assessment of electronic waste treatment

International Nuclear Information System (INIS)

Hong, Jinglan; Shi, Wenxiao; Wang, Yutao; Chen, Wei; Li, Xiangzhi

2015-01-01

Highlights: • Life cycle assessment of electronic waste recycling is quantified. • Key factors for reducing the overall environmental impact are indentified. • End-life disposal processes provide significant environmental benefits. • Efficiently reduce the improper disposal amount of e-waste is highly needed. • E-waste incineration can generate significant environmental burden. - Abstract: Life cycle assessment was conducted to estimate the environmental impact of electronic waste (e-waste) treatment. E-waste recycling with an end-life disposal scenario is environmentally beneficial because of the low environmental burden generated from human toxicity, terrestrial ecotoxicity, freshwater ecotoxicity, and marine ecotoxicity categories. Landfill and incineration technologies have a lower and higher environmental burden than the e-waste recycling with an end-life disposal scenario, respectively. The key factors in reducing the overall environmental impact of e-waste recycling are optimizing energy consumption efficiency, reducing wastewater and solid waste effluent, increasing proper e-waste treatment amount, avoiding e-waste disposal to landfill and incineration sites, and clearly defining the duties of all stakeholders (e.g., manufacturers, retailers, recycling companies, and consumers)

Life cycle assessment of electronic waste treatment

Energy Technology Data Exchange (ETDEWEB)

Hong, Jinglan, E-mail: hongjing@sdu.edu.cn [Shandong Provincial Key Laboratory of Water Pollution Control and Resource Reuse, School of Environmental Science and Engineering, Shandong University, Jinan 250100 (China); Shandong University Climate Change and Health Center, Public Health School, Shandong University, Jinan 250012 (China); Shi, Wenxiao [Shandong Provincial Key Laboratory of Water Pollution Control and Resource Reuse, School of Environmental Science and Engineering, Shandong University, Jinan 250100 (China); Wang, Yutao [School of Life Science, Shandong University, Shanda South Road 27, Jinan 250100 (China); Chen, Wei [Shandong Provincial Key Laboratory of Water Pollution Control and Resource Reuse, School of Environmental Science and Engineering, Shandong University, Jinan 250100 (China); Li, Xiangzhi, E-mail: xiangzhi@sdu.edu.cn [School of Medicine, Shandong University, Jinan 250012 (China)

2015-04-15

Highlights: • Life cycle assessment of electronic waste recycling is quantified. • Key factors for reducing the overall environmental impact are indentified. • End-life disposal processes provide significant environmental benefits. • Efficiently reduce the improper disposal amount of e-waste is highly needed. • E-waste incineration can generate significant environmental burden. - Abstract: Life cycle assessment was conducted to estimate the environmental impact of electronic waste (e-waste) treatment. E-waste recycling with an end-life disposal scenario is environmentally beneficial because of the low environmental burden generated from human toxicity, terrestrial ecotoxicity, freshwater ecotoxicity, and marine ecotoxicity categories. Landfill and incineration technologies have a lower and higher environmental burden than the e-waste recycling with an end-life disposal scenario, respectively. The key factors in reducing the overall environmental impact of e-waste recycling are optimizing energy consumption efficiency, reducing wastewater and solid waste effluent, increasing proper e-waste treatment amount, avoiding e-waste disposal to landfill and incineration sites, and clearly defining the duties of all stakeholders (e.g., manufacturers, retailers, recycling companies, and consumers)

Final Environmental Assessment for solid waste disposal, Nevada Test Site, Nye County, Nevada

International Nuclear Information System (INIS)

1995-08-01

New solid waste regulations require that the existing Nevada Test Site (NTS) municipal landfills, which receive less than 20 tons of waste per day, be permitted or closed by October 9, 1995. In order to be permitted, the existing landfills must meet specific location, groundwater monitoring, design, operation, and closure requirements. The issuance of these regulations has resulted in the need of the Department of Energy (DOE) to provide a practical, cost-effective, environmentally sound means of solid waste disposal at the NTS that is in compliance with all applicable federal, state, and local regulations. The current landfills in Areas 9 and 23 on the Nevada Test Site do not meet design requirements specified in new state and federal regulations. The DOE Nevada Operations Office prepared an environmental assessment (EA) to evaluate the potential impacts of the proposal to modify the Area 23 landfill to comply with the new regulations and to close the Area 9 landfill and reopen it as Construction and Demolition debris landfill. Based on information and analyses presented in the EA, DOE has determined that the proposed action would not constitute a major federal action significantly affecting the quality of the human environment within the meaning of the National Environmental Policy Act. Therefore, an environmental impact statement (EIS) is not required. This report contains the Environmental Assessment, as well as the Finding of No Significant Impact (FONSI)

Environmental Assessment for the construction and operation of the Three Rivers Solid Waste Authority regional waste management center at the Savannah River Site

International Nuclear Information System (INIS)

1995-12-01

This Environmental Assessment (EA) has been prepared by the US Department of Energy (DOE) to assess the potential environmental impacts associated with the construction and operation of a landfill and technology center for regionally-generated municipal solid waste at the Savannah River Site (SRS) near Aiken, South Carolina. The facility would serve the municipal solid waste disposal needs for SRS and at least nine of the surrounding counties who currently comprise the Three Rivers Solid Waste Authority (TRSWA). Additional counties could become included in the proposed action at some future date. Current Federal and state requirements do not afford individual counties and municipalities within the region encompassing SRS the ability to efficiently or economically operate modern waste management facilities. In addition, consolidation of regional municipal solid waste at one location would have the benefit of reducing the duplicity of environmental consequences associated with the construction and operation of county-level facilities. The option to seek a combined disposal and technology development facility based on a regionally-cooperative effort was selected as a viable alternative to the existing individual SRS or county disposal activities. This document was prepared in compliance with the National Environmental Policy Act (NEPA) of 1969, as amended, the requirements of the Council on Environmental Quality Regulations for Implementing NEPA (40 CFR Part 1021). NEPA requires the assessment of environmental consequences of Federal actions that may affect the quality of the human environment. Based on the potential for impacts described for impacts described herein, DOE will either publish a Finding of No Significant Impact or prepare an environmental impact statement (EIS)

Proposal of an environmental performance index to assess solid waste treatment technologies.

Science.gov (United States)

Coelho, Hosmanny Mauro Goulart; Lange, Liséte Celina; Coelho, Lineker Max Goulart

2012-07-01

Although the concern with sustainable development and environment protection has considerably grown in the last years it is noted that the majority of decision making models and tools are still either excessively tied to economic aspects or geared to the production process. Moreover, existing models focus on the priority steps of solid waste management, beyond waste energy recovery and disposal. So, in order to help the lack of models and tools aiming at the waste treatment and final disposal, a new concept is proposed: the Cleaner Treatment, which is based on the Cleaner Production principles. This paper focuses on the development and validation of the Cleaner Treatment Index (CTI), to assess environmental performance of waste treatment technologies based on the Cleaner Treatment concept. The index is formed by aggregation (summation or product) of several indicators that consists in operational parameters. The weights of the indicator were established by Delphi Method and Brazilian Environmental Laws. In addition, sensitivity analyses were carried out comparing both aggregation methods. Finally, index validation was carried out by applying the CTI to 10 waste-to-energy plants data. From sensitivity analysis and validation results it is possible to infer that summation model is the most suitable aggregation method. For summation method, CTI results were superior to 0.5 (in a scale from 0 to 1) for most facilities evaluated. So, this study demonstrates that CTI is a simple and robust tool to assess and compare the environmental performance of different treatment plants being an excellent quantitative tool to support Cleaner Treatment implementation. Copyright © 2012 Elsevier Ltd. All rights reserved.

Environmental assessment of solid waste landfilling technologies by means of LCA-modeling

DEFF Research Database (Denmark)

Manfredi, Simone; Christensen, Thomas Højlund

2009-01-01

By using life cycle assessment (LCA) modeling, this paper compares the environmental performance of six landfilling technologies (open dump, conventional landfill with flares, conventional landfill with energy recovery, standard bioreactor landfill, flushing bioreactor landfill and semi......-aerobic landfill) and assesses the influence of the active operations practiced on these performances. The environmental assessments have been performed by means of the LCA-based tool EASEWASTE, whereby the functional unit utilized for the LCA is “landfilling of 1 ton of wet household waste in a 10 m deep landfill...... that it is crucially important to ensure the highest collection efficiency of landfill gas and leachate since a poor capture compromises the overall environmental performance. Once gas and leachate are collected and treated, the potential impacts in the standard environmental categories and on spoiled groundwater...

Environmental impact assessment of the incineration of municipal solid waste with auxiliary coal in China

DEFF Research Database (Denmark)

Zhao, Yan; Xing, Wei; Lu, Wenjing

2012-01-01

The environmental impacts of waste incineration with auxiliary coal were investigated using the life-cycle-based software, EASEWASTE, based on the municipal solid waste (MSW) management system in Shuozhou City. In the current system, MSW is collected, transported, and incinerated with 250kg of coal...... per ton of waste. Based on observed environmental impacts of incineration, fossil CO2 and heavy metals were primary contributors to global warming and ecotoxicity in soil, respectively. Compared with incinerators using excess coal, incineration with adequate coal presents significant benefits......-separated and landfilled, the incineration of rest-waste presents better results on global warming, acidification, nutrient enrichment, and even ecotoxicity in soil. This process is considered a promising solution for MSW management in Shuozhou City. Weighted normalized environmental impacts were assessed based on Chinese...

Hazardous waste treatment and environmental remediation research

International Nuclear Information System (INIS)

1989-01-01

Los Alamos National Laboratory (LANL) is currently evaluating hazardous waste treatment and environmental remediation technologies in existence and under development to determine applicability to remediation needs of the DOE facilities under the Albuquerque Operations Office and to determine areas of research need. To assist LANL is this effort, Science Applications International Corporation (SAIC) conducted an assessment of technologies and monitoring methods that have been demonstrated or are under development. The focus of this assessment is to: (1) identify existing technologies for hazardous waste treatment and environmental remediation of old waste sites; (2) identify technologies under development and the status of the technology; (3) assess new technologies that need development to provide adequate hazardous waste treatment and remedial action technologies for DOD and DOE sites; and (4) identify hazardous waste and remediation problems for environmental research and development. There are currently numerous research and development activities underway nationwide relating to environmental contaminants and the remediation of waste sites. To perform this effort, SAIC evaluated current technologies and monitoring methods development programs in EPA, DOD, and DOE, as these are the primary agencies through which developmental methods are being demonstrated. This report presents this evaluation and provides recommendations as to pertinent research needs or activities to address waste site contamination problems. The review and assessment have been conducted at a programmatic level; site-specific and contaminant-specific evaluations are being performed by LANL staff as a separate, related activity

Construction and operation of replacement hazardous waste handling facility at Lawrence Berkeley Laboratory. Environmental Assessment

Energy Technology Data Exchange (ETDEWEB)

1992-09-01

The US Department of Energy (DOE) has prepared an environmental assessment (EA), DOE/EA-0423, for the construction and operation of a replacement hazardous waste handling facility (HWHF) and decontamination of the existing HWHF at Lawrence Berkeley Laboratory (LBL), Berkeley, California. The proposed facility would replace several older buildings and cargo containers currently being used for waste handling activities and consolidate the LBL`s existing waste handling activities in one location. The nature of the waste handling activities and the waste volume and characteristics would not change as a result of construction of the new facility. Based on the analysis in the EA, DOE has determined that the proposed action would not constitute a major Federal action significantly affecting the quality of the human environment within the meaning of the National Environmental Policy Act (NEPA) of 1969, 42 USC. 4321 et seq. Therefore, an environmental impact statement is not required.

Environmental impact assessment of solid waste management in Beijing City, China

International Nuclear Information System (INIS)

Zhao Yan; Christensen, Thomas H.; Lu Wenjing; Wu Huayong; Wang Hongtao

2011-01-01

The environmental impacts of municipal solid waste management in Beijing City were evaluated using a life-cycle-based model, EASEWASTE, to take into account waste generation, collection, transportation, treatment/disposal technologies, and savings obtained by energy and material recovery. The current system, mainly involving the use of landfills, has manifested significant adverse environmental impacts caused by methane emissions from landfills and many other emissions from transfer stations. A short-term future scenario, where some of the landfills (which soon will reach their capacity because of rising amount of waste in Beijing City) are substituted by incinerators with energy recovery, would not result in significant environmental improvement. This is primarily because of the low calorific value of mixed waste, and it is likely that the incinerators would require significant amounts of auxiliary fuels to support combustion of wet waste. As for the long-term future scenario, efficient source separation of food waste could result in significant environmental improvements, primarily because of increase in calorific value of remaining waste incinerated with energy recovery. Sensitivity analysis emphasized the importance of efficient source separation of food waste, as well as the electricity recovery in incinerators, in order to obtain an environmentally friendly waste management system in Beijing City.

Identification and development of waste management alternatives for Strategic Environmental Assessment (SEA)

International Nuclear Information System (INIS)

Desmond, Margaret

2009-01-01

The European Union Strategic Environmental Assessment (SEA) Directive (2001/42/EC) requires the assessment of likely significant effects on the environment of implementing plans or programmes and reasonable alternatives. While SEA regulations and guidelines emphasize rigour and objectivity in the assessment of alternatives they have little to say on their actual identification. Therefore, criteria should be developed which would aid decision makers in the identification of alternatives appropriate to the tier of decision-making and which meet the objectives of SEA. A methodology is set out in this paper for identifying SEA alternatives for a proposed waste management plan/programme. Specifically, the methodology describes a set of alternatives identification criteria, which will meet the requirements and objectives of SEA and waste management legislation. The outputs from the methodology will help focus on the identification of more sustainable alternatives for waste management planning in Ireland

Environmental impact assessment of solid waste management in Beijing City, China

DEFF Research Database (Denmark)

Zhao, Yan; Christensen, Thomas Højlund; Lu, Wenjing

2011-01-01

The environmental impacts of municipal solid waste management in Beijing City were evaluated using a life-cycle-based model, EASEWASTE, to take into account waste generation, collection, transportation, treatment/disposal technologies, and savings obtained by energy and material recovery...... analysis emphasized the importance of efficient source separation of food waste, as well as the electricity recovery in incinerators, in order to obtain an environmentally friendly waste management system in Beijing City....... because of rising amount of waste in Beijing City) are substituted by incinerators with energy recovery, would not result in significant environmental improvement. This is primarily because of the low calorific value of mixed waste, and it is likely that the incinerators would require significant amounts...

ENVIRONMENTAL RESEARCH BRIEF: WASTE MINIMIZATION ASSESSMENT FOR A MANUFACTURER OF REBUILT RAILWAY CARS AND COMPONENTS

Science.gov (United States)

The U.S. Environmental Protection Agency (EPA) has funded a pilot project to assist small- and medium- size manufacturers who want to minimize their generation of hazardous waste but lack the expertise to do so. Waste Minimization Assessment Centers (WMACs) were established at se...

E-waste: an assessment of global production and environmental impacts.

Science.gov (United States)

Robinson, Brett H

2009-12-20

E-waste comprises discarded electronic appliances, of which computers and mobile telephones are disproportionately abundant because of their short lifespan. The current global production of E-waste is estimated to be 20-25 million tonnes per year, with most E-waste being produced in Europe, the United States and Australasia. China, Eastern Europe and Latin America will become major E-waste producers in the next ten years. Miniaturisation and the development of more efficient cloud computing networks, where computing services are delivered over the internet from remote locations, may offset the increase in E-waste production from global economic growth and the development of pervasive new technologies. E-waste contains valuable metals (Cu, platinum group) as well as potential environmental contaminants, especially Pb, Sb, Hg, Cd, Ni, polybrominated diphenyl ethers (PBDEs), and polychlorinated biphenyls (PCBs). Burning E-waste may generate dioxins, furans, polycyclic aromatic hydrocarbons (PAHs), polyhalogenated aromatic hydrocarbons (PHAHs), and hydrogen chloride. The chemical composition of E-waste changes with the development of new technologies and pressure from environmental organisations on electronics companies to find alternatives to environmentally damaging materials. Most E-waste is disposed in landfills. Effective reprocessing technology, which recovers the valuable materials with minimal environmental impact, is expensive. Consequently, although illegal under the Basel Convention, rich countries export an unknown quantity of E-waste to poor countries, where recycling techniques include burning and dissolution in strong acids with few measures to protect human health and the environment. Such reprocessing initially results in extreme localised contamination followed by migration of the contaminants into receiving waters and food chains. E-waste workers suffer negative health effects through skin contact and inhalation, while the wider community are exposed

E-waste: An assessment of global production and environmental impacts

International Nuclear Information System (INIS)

Robinson, Brett H.

2009-01-01

E-waste comprises discarded electronic appliances, of which computers and mobile telephones are disproportionately abundant because of their short lifespan. The current global production of E-waste is estimated to be 20-25 million tonnes per year, with most E-waste being produced in Europe, the United States and Australasia. China, Eastern Europe and Latin America will become major E-waste producers in the next ten years. Miniaturisation and the development of more efficient cloud computing networks, where computing services are delivered over the internet from remote locations, may offset the increase in E-waste production from global economic growth and the development of pervasive new technologies. E-waste contains valuable metals (Cu, platinum group) as well as potential environmental contaminants, especially Pb, Sb, Hg, Cd, Ni, polybrominated diphenyl ethers (PBDEs), and polychlorinated biphenyls (PCBs). Burning E-waste may generate dioxins, furans, polycyclic aromatic hydrocarbons (PAHs), polyhalogenated aromatic hydrocarbons (PHAHs), and hydrogen chloride. The chemical composition of E-waste changes with the development of new technologies and pressure from environmental organisations on electronics companies to find alternatives to environmentally damaging materials. Most E-waste is disposed in landfills. Effective reprocessing technology, which recovers the valuable materials with minimal environmental impact, is expensive. Consequently, although illegal under the Basel Convention, rich countries export an unknown quantity of E-waste to poor countries, where recycling techniques include burning and dissolution in strong acids with few measures to protect human health and the environment. Such reprocessing initially results in extreme localised contamination followed by migration of the contaminants into receiving waters and food chains. E-waste workers suffer negative health effects through skin contact and inhalation, while the wider community are exposed

E-waste: An assessment of global production and environmental impacts

Energy Technology Data Exchange (ETDEWEB)

Robinson, Brett H., E-mail: brett.robinson@lincoln.ac.nz [Department of Soil and Physical Sciences, Lincoln University, Lincoln 7647, Canterbury (New Zealand)

2009-12-20

E-waste comprises discarded electronic appliances, of which computers and mobile telephones are disproportionately abundant because of their short lifespan. The current global production of E-waste is estimated to be 20-25 million tonnes per year, with most E-waste being produced in Europe, the United States and Australasia. China, Eastern Europe and Latin America will become major E-waste producers in the next ten years. Miniaturisation and the development of more efficient cloud computing networks, where computing services are delivered over the internet from remote locations, may offset the increase in E-waste production from global economic growth and the development of pervasive new technologies. E-waste contains valuable metals (Cu, platinum group) as well as potential environmental contaminants, especially Pb, Sb, Hg, Cd, Ni, polybrominated diphenyl ethers (PBDEs), and polychlorinated biphenyls (PCBs). Burning E-waste may generate dioxins, furans, polycyclic aromatic hydrocarbons (PAHs), polyhalogenated aromatic hydrocarbons (PHAHs), and hydrogen chloride. The chemical composition of E-waste changes with the development of new technologies and pressure from environmental organisations on electronics companies to find alternatives to environmentally damaging materials. Most E-waste is disposed in landfills. Effective reprocessing technology, which recovers the valuable materials with minimal environmental impact, is expensive. Consequently, although illegal under the Basel Convention, rich countries export an unknown quantity of E-waste to poor countries, where recycling techniques include burning and dissolution in strong acids with few measures to protect human health and the environment. Such reprocessing initially results in extreme localised contamination followed by migration of the contaminants into receiving waters and food chains. E-waste workers suffer negative health effects through skin contact and inhalation, while the wider community are exposed

Environmental Modeling and Bayesian Analysis for Assessing Human Health Impacts from Radioactive Waste Disposal

Science.gov (United States)

Stockton, T.; Black, P.; Tauxe, J.; Catlett, K.

2004-12-01

Bayesian decision analysis provides a unified framework for coherent decision-making. Two key components of Bayesian decision analysis are probability distributions and utility functions. Calculating posterior distributions and performing decision analysis can be computationally challenging, especially for complex environmental models. In addition, probability distributions and utility functions for environmental models must be specified through expert elicitation, stakeholder consensus, or data collection, all of which have their own set of technical and political challenges. Nevertheless, a grand appeal of the Bayesian approach for environmental decision- making is the explicit treatment of uncertainty, including expert judgment. The impact of expert judgment on the environmental decision process, though integral, goes largely unassessed. Regulations and orders of the Environmental Protection Agency, Department Of Energy, and Nuclear Regulatory Agency orders require assessing the impact on human health of radioactive waste contamination over periods of up to ten thousand years. Towards this end complex environmental simulation models are used to assess "risk" to human and ecological health from migration of radioactive waste. As the computational burden of environmental modeling is continually reduced probabilistic process modeling using Monte Carlo simulation is becoming routinely used to propagate uncertainty from model inputs through model predictions. The utility of a Bayesian approach to environmental decision-making is discussed within the context of a buried radioactive waste example. This example highlights the desirability and difficulties of merging the cost of monitoring, the cost of the decision analysis, the cost and viability of clean up, and the probability of human health impacts within a rigorous decision framework.

Environmental integrated impact assessment for waste treatment activity: methodology and case-study application

International Nuclear Information System (INIS)

Lonati, G.; Panzeri, A.

2008-01-01

A literature method for the environmental integrated impact assessment, according to the IPPC Directive, has been critically analysed and adjusted in order to be used for the environmental performance assessment of waste treatment activities. The assessment parameters, sorted in eight treatment and combined pollution categories, have been partly redefined and re balanced. The adjusted methodology has been applied to a real case-study, a chemical- physical waste treatment plant, in order to calculate the current performance (Actual Integrated Index) and the ideal performance (Actual Integrated Index) achievable by technical and operational improvements. The adjusted methodology has also been used as a decision support system, in order to estimate the value of the expected environmental performances improvement after the execution achievable from the introduction of a single one or a set of improvement actions. The valuation of the Integrated Index percentage reduction, along with the action achievable, made the best actions able to be identified, both in comparative way and in the cost-effective one. The results, 50 as Effective Integrated Index and 42 as Ideal Integrated Index, in a 10-100 scale, show a medium impact level and point out an appreciable improvement margin on all the environmental performances, especially in air emission control and water consumption [it

Environmental assessment of different management options for individual waste fractions by means of life-cycle assessment modelling

DEFF Research Database (Denmark)

Manfredi, Simone; Tonini, Davide; Christensen, Thomas Højlund

2011-01-01

and environmental factors involved, including energy generation from landfill gas and storage of biogenic carbon. Leachate and gas emissions associated to each individual waste fraction have been estimated by means of a mathematical modelling. This approach towards landfilling emissions allows for a more precise...... quantification of the landfill impacts when comparing management options for selected waste fractions.Results from the life-cycle impact assessment (LCIA) show that the environmental performance estimated for landfilling with energy recovery of the fractions “organics” and “recyclable paper” is comparable...... with composting (for “organics”) and incineration (for “recyclable paper”). This however requires high degree of control over gas and leachate emissions, high gas collection efficiency and extensive gas utilization at the landfill. For the other waste fractions, recycling and incineration are favourable, although...

Environmental assessment for the construction, operation, and decommissioning of the Waste Segregation Facility at the Savannah River Site

International Nuclear Information System (INIS)

1998-01-01

This Environmental Assessment (EA) has been prepared by the Department of Energy (DOE) to assess the potential environmental impacts associated with the construction, operation and decontamination and decommissioning (D ampersand D) of the Waste Segregation Facility (WSF) for the sorting, shredding, and compaction of low-level radioactive waste (LLW) at the Savannah River Site (SRS) located near Aiken, South Carolina. The LLW to be processed consists of two waste streams: legacy waste which is currently stored in E-Area Vaults of SRS and new waste generated from continuing operations. The proposed action is to construct, operate, and D ampersand D a facility to process low-activity job-control and equipment waste for volume reduction. The LLW would be processed to make more efficient use of low-level waste disposal capacity (E-Area Vaults) or to meet the waste acceptance criteria for treatment at the Consolidated Incineration Facility (CIF) at SRS

Fuzzy distributions in probabilistic environmental impact assessment: application to a high-level waste repository

International Nuclear Information System (INIS)

Datta, D.; Joshi, M.L.

2006-01-01

Environmental modeling with a satisfaction levels of the end user in relation to a defined parameter coupled with imprecision that stems from the field data is a key issue. In the context of this issue success of possibility theory based on fuzzy sets has high visibility in comparison with conventional probability theory. Environmental impact assessments of a high level waste repository is focused using the new approach because the problems under consideration includes a number of qualitative uncertainties at different levels, apart from being quite complex; decision-maker's need to have a transparent assessment result that will enable him to understand underlying assumptions and to judge resulting doses. Fuzzy distributions have been tried to resolve the issues related to the safety of environment from the waste repository. Paper describes the details of fuzzy distribution, fuzzy logic and its possible application to deal the qualitative and quantitative uncertainty in connection with waste repository. (author)

Low- and Intermediate Level Radioactive Waste Disposal Environmental and Safety Assessment Activities in Slovenia

International Nuclear Information System (INIS)

Marc, D.; Loose, A.; Urbanc, J.

1998-01-01

The protection of the environment is one of the main concerns in the management of radioactive waste, especially in repository planning. In different stages of repository lifetime the environmental assessment has different functions: it can be used as a decision making process and as a planning, communication and management tool. Safety assessment as a procedure for evaluating the performance of a disposal system, and its potential radiological impact on human health and environment, is also required. Following the international recommendations and Slovene legislation, a presentation is given of the role and importance of the environmental and safety assessment activities in the early stages following concept development and site selection for a low- and intermediate level radioactive waste (LILW) repository in Slovenia. As a case study, a short overview is also given of the preliminary safety assessment that has been carried out in the analysis of possibilities for long-lived LILW disposal in Slovenia. (author)

Environmental evaluation of municipal waste prevention

DEFF Research Database (Denmark)

Gentil, Emmanuel; Gallo, Daniele; Christensen, Thomas Højlund

2011-01-01

society, using life-cycle thinking. The partial prevention of unsolicited mail, beverage packaging and food waste is tested for a “High-tech” waste management system relying on high energy and material recovery and for a “Low-tech” waste management system with less recycling and relying on landfilling......Waste prevention has been addressed in the literature in terms of the social and behavioural aspects, but very little quantitative assessment exists of the environmental benefits. Our study evaluates the environmental consequences of waste prevention on waste management systems and on the wider....... Prevention of 13% of the waste mass entering the waste management system generates a reduction of loads and savings in the waste management system for the different impacts categories; 45% net reduction for nutrient enrichment and 12% reduction for global warming potential. When expanding our system...

Risk assessment for the on-site transportation of radioactive wastes for the U.S. Department of Energy Waste Management Programmatic Environmental Impact Statement

International Nuclear Information System (INIS)

Biwer, B.M.; Monette, F.A.; Chen, S.Y.

1996-12-01

This report documents the risk assessment performed for the on-site transportation of radioactive wastes in the US Department of Energy (DOE) Waste Management Programmatic Environmental Impact Statement (WM PEIS). Risks for the routine shipment of wastes and the impacts from potential accidental releases are analyzed for operations at the Hanford Site (Hanford) near Richland, Washington. Like other large DOE sites, hanford conducts waste management operations for all wastes types; consequently, the impacts calculated for Hanford are expected to be greater than those for smaller sites. The risk assessment conducted for on-site transportation is intended to provide an estimate of the magnitude of the potential risk for comparison with off-site transportation risks assessed for the WM PEIS

Los Alamos low-level waste performance assessment status

International Nuclear Information System (INIS)

Wenzel, W.J.; Purtymun, W.D.; Dewart, J.M.; Rodgers, J.E.

1986-06-01

This report reviews the documented Los Alamos studies done to assess the containment of buried hazardous wastes. Five sections logically present the environmental studies, operational source terms, transport pathways, environmental dosimetry, and computer model development and use. This review gives a general picture of the Los Alamos solid waste disposal and liquid effluent sites and is intended for technical readers with waste management and environmental science backgrounds but without a detailed familiarization with Los Alamos. The review begins with a wide perspective on environmental studies at Los Alamos. Hydrology, geology, and meteorology are described for the site and region. The ongoing Laboratory-wide environmental surveillance and waste management environmental studies are presented. The next section describes the waste disposal sites and summarizes the current source terms for these sites. Hazardous chemical wastes and liquid effluents are also addressed by describing the sites and canyons that are impacted. The review then focuses on the transport pathways addressed mainly in reports by Healy and Formerly Utilized Sites Remedial Action Program. Once the source terms and potential transport pathways are described, the dose assessment methods are addressed. Three major studies, the waste alternatives, Hansen and Rogers, and the Pantex Environmental Impact Statement, contributed to the current Los Alamos dose assessment methodology. Finally, the current Los Alamos groundwater, surface water, and environmental assessment models for these mesa top and canyon sites are described

Waste management in the Irkutsk region, Siberia, Russia: An environmental assessment of alternative development scenarios.

Science.gov (United States)

Starostina, Vlada; Damgaard, Anders; Eriksen, Marie K; Christensen, Thomas H

2018-04-01

The current waste management system, handling around 500,000 t of household, commercial, and institutional waste annually in the Irkutsk region, Siberia, is based on landfilling in an old landfill with no controls of leachate and gas. Life-cycle assessment modelling of the current system shows that it is a major load on the environment, while the simulation of seven alternative systems results in large savings in many impact categories. With respect to climate change, it is estimated that a saving of about 1200 kg CO 2 equivalents is possible per year, per inhabitant, which is a significant reduction in greenhouse gas emissions. The best alternatives involve efficient energy recovery from waste and recycling by source separation for commercial and institutional waste, the major waste type in the Irkutsk region. Recycling of household waste seems less attractive, and it is therefore recommended only to consider this option after experience has been gained with the commercial and institutional waste. Sensitivity analysis shows that recovery of energy - in particular electricity, heat, and steam - from waste is crucial to the environmental performance of the waste management system. This relates to the efficiencies of energy recovery as well as what the recovered energy substitutes, that is, the 'dirtier' the off-set energy, the higher the environmental savings for the waste management system. Since recovered energy may be utilised by only a few energy grids or industrial users, it is recommended to perform additional local assessments of the integration of the waste energy into existing systems and facilities.

Environmental impact assessments and geological repositories for radioactive waste

International Nuclear Information System (INIS)

O'Sullivan, P.; McKirdy, B.; Askarieh, M.; Bond, A.; Russell, S.

1999-01-01

Since 1985 it has been obligatory that facilities in the European Union designed for the permanent storage or disposal of radioactive waste be assessed to determine their effects on the environment. This assessment must be undertaken in advance of any decision by national authorities to give consent for development work to proceed. Member States are given wide discretion on how the above requirements are implemented in practice, e.g. the relevant European Council Directives call for the results of the environmental assessment to be made available to the public before development consent is granted but the detailed arrangements for dissemination of such information and procedures for public consultation are determined by individual Member States. Although the Directives require an assessment of the direct and indirect effects of a project on human beings and on various elements of the natural environment, they are non-specific as to what particular impacts should be addressed, particularly as regards the effects of a project on human beings. Therefore, for example, each Member State may decide whether or not social, health and economic impacts should be included in the assessment. This paper discusses the above issues. It proposes a model approach to environmental impact assessment in the context of geological repositories, including the role of the assessment on the overall decision processes for repository development, the scope and content of the assessment report, and approaches to public involvement

Risk assessment for the on-site transportation of radioactive wastes for the U.S. Department of Energy Waste Management programmatic environmental impact statement

International Nuclear Information System (INIS)

Biwer, B.M.; Monette, F.A.; Chen, S.Y.

1995-04-01

This report documents the risk assessment performed for the on-site transportation of radioactive wastes in the U.S. Department of Energy (DOE) Waste Management (WM) Programmatic Environmental Impact Statement (PEIS). Risks for the routine shipment of wastes and the impacts from potential accidental releases are analyzed for operations at the Hanford Site (Hanford) near Richland, Washington. Like other large DOE sites, Hanford conducts waste management operations for all wastes types; consequently, the impacts calculated for Hanford are expected to be greater than those for smaller sites. The risk assessment conducted for on-site transportation is intended to provide an estimate of the magnitude of the potential risk for comparison with off-site transportation risks assessed for the WM PEIS

Uncertainties in environmental impact assessments due to expert opinion. Case study. Radioactive waste in Slovenia

International Nuclear Information System (INIS)

Kontic, B.; Ravnik, M.

1998-01-01

A comprehensive study was done at the J. Stefan Institute in Ljubljana and the School of Environmental Sciences in Nova Gorica in relation to sources of uncertainties in long-term environmental impact assessment (EIA). Under the research two main components were examined: first, methodology of the preparation of an EIA, and second validity of an expert opinion. Following the findings of the research a survey was performed in relation to assessing acceptability of radioactive waste repository by the regulatory. The components of dose evaluation in different time frames were examined in terms of susceptibility to uncertainty. Uncertainty associated to human exposure in the far future is so large that dose and risk, as individual numerical indicators of safety, by our opinion, should not be used in compliance assessment for radioactive waste repository. On the other hand, results of the calculations on the amount and activity of low and intermediate level waste and the spent fuel from the Krsko NPP show that expert's understanding of the treated questions can be expressed in transparent way giving credible output of the models used.(author)

Environmental impact assessment for a radioactive waste facility: A case study

International Nuclear Information System (INIS)

Devgun, J.S.

1990-01-01

A 77-ha site, known as the Niagara Falls Storage Site and located in northwestern New York State, holds about 190, 000 m 3 of soils, wastes, and residues contaminated with radium and uranium. The facility is owned by the US Department of Energy. The storage of residues resulting from the processing of uranium ores started in 1944, and by 1950 residues from a number of plants were received at the site. The residues, with a volume of about 18,000 m 3 , account for the bulk of the radioactivity, which is primarily due to Ra-226; because of the extraction of uranium from the ore, the amount of uranium remaining in the residues is quite small. An analysis of the environmental impact assessment and environmental compliance actions taken to date at this site and their effectiveness are discussed. This case study provides an illustrative example of the complexity of technical and nontechnical issues for a large radiative waste facility. 11 refs., 7 figs., 2 tabs

Radioactive waste disposal - ethical and environmental considerations - A Canadian perspective

International Nuclear Information System (INIS)

Roots, F.

1994-01-01

This work deals with ethical and environmental considerations of radioactive waste disposal in Canada. It begins with the canadian attitudes toward nature and environment. Then are given the canadian institutions which reflect an environmental ethic, the development of a canadian radioactive waste management policy, the establishment of formal assessment and review process for a nuclear fuel waste disposal facility, some studies of the ethical and risk dimensions of nuclear waste decisions, the canadian societal response to issues of radioactive wastes, the analysis of risks associated with fuel waste disposal, the influence of other energy related environmental assessments and some common ground and possible accommodation between the different views. (O.L.). 50 refs

The role of quantitative optimization techniques in assessment of best practicable environmental options for radioactive waste management

International Nuclear Information System (INIS)

Johnston, P.D.

1987-01-01

The interpretation of the Best Practicable Environmental Option (BPEO) and ALARA concepts in radioactive waste management is given. The quantitative analysis of the financial and radiological impacts of different options for waste management is discussed. Finally, the role of quantitative multi-attribute analysis in the DOE's assessment of BPEOs for radioactive waste is described. (UK)

Environmental evaluation of municipal waste prevention

International Nuclear Information System (INIS)

Gentil, Emmanuel C.; Gallo, Daniele; Christensen, Thomas H.

2011-01-01

Highlights: → Influence of prevention on waste management systems, excluding avoided production, is relatively minor. → Influence of prevention on overall supply chain, including avoided production is very significant. → Higher relative benefits of prevention are observed in waste management systems relying mainly on landfills. - Abstract: Waste prevention has been addressed in the literature in terms of the social and behavioural aspects, but very little quantitative assessment exists of the environmental benefits. Our study evaluates the environmental consequences of waste prevention on waste management systems and on the wider society, using life-cycle thinking. The partial prevention of unsolicited mail, beverage packaging and food waste is tested for a 'High-tech' waste management system relying on high energy and material recovery and for a 'Low-tech' waste management system with less recycling and relying on landfilling. Prevention of 13% of the waste mass entering the waste management system generates a reduction of loads and savings in the waste management system for the different impacts categories; 45% net reduction for nutrient enrichment and 12% reduction for global warming potential. When expanding our system and including avoided production incurred by the prevention measures, large savings are observed (15-fold improvement for nutrient enrichment and 2-fold for global warming potential). Prevention of food waste has the highest environmental impact saving. Prevention generates relatively higher overall relative benefit for 'Low-tech' systems depending on landfilling. The paper provides clear evidence of the environmental benefits of waste prevention and has specific relevance in climate change mitigation.

Environmental aspects of commercial radioactive waste management

International Nuclear Information System (INIS)

1979-05-01

Volume 3 contains eight appendices: a reference environment for assessing environmental impacts associated with construction and operation of waste treatment, interim storage and/or final disposition facilities; dose calculations and radiologically related health effects; socioeconomic impact assessments; release/dose factors and dose in 5-year intervals to regional and world wide population from reference integrated systems; resource availability; environmental monitoring; detailed dose results for radionuclide migration groundwater from a waste repository; and annual average dispersion factors for selected release points

Environmental aspects of commercial radioactive waste management

Energy Technology Data Exchange (ETDEWEB)

1979-05-01

Volume 3 contains eight appendices: a reference environment for assessing environmental impacts associated with construction and operation of waste treatment, interim storage and/or final disposition facilities; dose calculations and radiologically related health effects; socioeconomic impact assessments; release/dose factors and dose in 5-year intervals to regional and world wide population from reference integrated systems; resource availability; environmental monitoring; detailed dose results for radionuclide migration groundwater from a waste repository; and annual average dispersion factors for selected release points. (LK)

Life cycle assessment of electronic waste treatment.

Science.gov (United States)

Hong, Jinglan; Shi, Wenxiao; Wang, Yutao; Chen, Wei; Li, Xiangzhi

2015-04-01

Life cycle assessment was conducted to estimate the environmental impact of electronic waste (e-waste) treatment. E-waste recycling with an end-life disposal scenario is environmentally beneficial because of the low environmental burden generated from human toxicity, terrestrial ecotoxicity, freshwater ecotoxicity, and marine ecotoxicity categories. Landfill and incineration technologies have a lower and higher environmental burden than the e-waste recycling with an end-life disposal scenario, respectively. The key factors in reducing the overall environmental impact of e-waste recycling are optimizing energy consumption efficiency, reducing wastewater and solid waste effluent, increasing proper e-waste treatment amount, avoiding e-waste disposal to landfill and incineration sites, and clearly defining the duties of all stakeholders (e.g., manufacturers, retailers, recycling companies, and consumers). Copyright © 2015 Elsevier Ltd. All rights reserved.

Environmental aspects of commercial radioactive waste management

Energy Technology Data Exchange (ETDEWEB)

1979-05-01

Environmental effects (including accidents) associated with facility construction, operation, decommissioning, and transportation in the management of commercially generated radioactive waste were analyzed for plants and systems assuming a light water power reactor scenario that produces about 10,000 GWe-yr through the year 2050. The following alternative fuel cycle modes or cases that generate post-fission wastes requiring management were analyzed: a once-through option, a fuel reprocessing option for uranium and plutonium recycle, and a fuel reprocessing option for uranium-only recycle. Volume 1 comprises five chapters: introduction; summary of findings; approach to assessment of environmental effects from radioactive waste management; environmental effects related to radioactive management in a once-through fuel cycle; and environmental effects of radioactive waste management associated with an LWR fuel reprocessing plant. (LK)

Environmental aspects of commercial radioactive waste management

International Nuclear Information System (INIS)

1979-05-01

Environmental effects (including accidents) associated with facility construction, operation, decommissioning, and transportation in the management of commercially generated radioactive waste were analyzed for plants and systems assuming a light water power reactor scenario that produces about 10,000 GWe-yr through the year 2050. The following alternative fuel cycle modes or cases that generate post-fission wastes requiring management were analyzed: a once-through option, a fuel reprocessing option for uranium and plutonium recycle, and a fuel reprocessing option for uranium-only recycle. Volume 1 comprises five chapters: introduction; summary of findings; approach to assessment of environmental effects from radioactive waste management; environmental effects related to radioactive management in a once-through fuel cycle; and environmental effects of radioactive waste management associated with an LWR fuel reprocessing plant

Hanford Site waste management and environmental restoration integration plan

International Nuclear Information System (INIS)

Merrick, D.L.

1990-01-01

The ''Hanford Site Waste Management and Environmental Restoration Integration Plan'' describes major actions leading to waste disposal and site remediation. The primary purpose of this document is to provide a management tool for use by executives who need to quickly comprehend the waste management and environmental restoration programs. The Waste Management and Environmental Restoration Programs have been divided into missions. Waste Management consists of five missions: double-shell tank (DST) wastes; single-shell tank (SST) wastes (surveillance and interim storage, stabilization, and isolation); encapsulated cesium and strontium; solid wastes; and liquid effluents. Environmental Restoration consists of two missions: past practice units (PPU) (including characterization and assessment of SST wastes) and surplus facilities. For convenience, both aspects of SST wastes are discussed in one place. A general category of supporting activities is also included. 20 refs., 14 figs., 7 tabs

Environmental assessment for the construction and operation of waste storage facilities at the Paducah Gaseous Diffusion Plant, Paducah, Kentucky

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-06-01

DOE is proposing to construct and operate 3 waste storage facilities (one 42,000 ft{sup 2} waste storage facility for RCRA waste, one 42,000 ft{sup 2} waste storage facility for toxic waste (TSCA), and one 200,000 ft{sup 2} mixed (hazardous/radioactive) waste storage facility) at Paducah. This environmental assessment compares impacts of this proposed action with those of continuing present practices aof of using alternative locations. It is found that the construction, operation, and ultimate closure of the proposed waste storage facilities would not significantly affect the quality of the human environment within the meaning of NEPA; therefore an environmental impact statement is not required.

Environmental assessment for the construction and operation of waste storage facilities at the Paducah Gaseous Diffusion Plant, Paducah, Kentucky

International Nuclear Information System (INIS)

1994-06-01

DOE is proposing to construct and operate 3 waste storage facilities (one 42,000 ft 2 waste storage facility for RCRA waste, one 42,000 ft 2 waste storage facility for toxic waste (TSCA), and one 200,000 ft 2 mixed (hazardous/radioactive) waste storage facility) at Paducah. This environmental assessment compares impacts of this proposed action with those of continuing present practices aof of using alternative locations. It is found that the construction, operation, and ultimate closure of the proposed waste storage facilities would not significantly affect the quality of the human environment within the meaning of NEPA; therefore an environmental impact statement is not required

Environmental impact assessment and socio political issues of nuclear waste management

International Nuclear Information System (INIS)

Harmaajaervi, I.; Tolsa, H.

1997-09-01

The study is a part of the Publicly Administrated Nuclear Waste Management Research Programme (JYT2) which was carried out in 1994-1996. The principal goal of the research programme has been to provide the authorities with information and research results relevant for the safety of nuclear waste management in order to support the various activities of the authorities. The main emphasis of the research programme focuses on the disposal of spent fuel. In addition to nuclear waste research in the field of natural sciences and technology, the research program- me has focused mostly on societal issues associated with nuclear waste disposal facilities and on the non-radiological environmental effects in the environs of the disposal site. Some of the local effects are already revealed in the research phase, before any final decisions are made as to the selection of the disposal site. The study has focused primarily on local and regional issues. The statutory requirement to conduct environ- mental impact assessment (EIA) chiefly concerns those who are responsible for waste management, but the authorities also need to acquire systematic information in the field to support developing requirements for the content and scope of EIA procedure and preparedness to check the assessments made. This is a report of the first parts of the study in 1994-1995. The report deals with the subject matter generally based on earlier studies in Finland and other countries. The results of the study will be reported later

Environmental epidemiology, Volume 1: Public health and hazardous wastes

International Nuclear Information System (INIS)

Anon.

1991-01-01

Environmental Epidemiology, Volume 1, represents the first of several planned volumes on the uses of epidemiologic techniques to study environmental public health issues. This text focuses on environmental epidemiology as it relates to hazardous waste in the United States. This study was commissioned by the Agency for Toxic Substances and Disease Registry to examine available data for evidence of adverse health effects on human populations exposed to hazardous waste. The committee was also asked to identify data gaps which were impediments to analyzing hazardous waste health effects and to suggest ways that such environmental health assessments might be improved. The committee's solution to the paucity of data on this issue was to concentrate in this volume on identifying the available, peer-reviewed data and, consequently, the major data gaps. The study opens with a recapitulation of the context of hazardous waste sites in the United States, the approaches currently used by state and federal epidemiologists in analyzing hazardous waste exposure and effects, and candid assessment of the problems associated with environmental exposure assessment. From that context, the committee then presents the data currently available to assess human exposures through air, domestic water consumption, soil, and the food chain. The general focus here is on biomarker data as the date of choice. As with all NAS reports, this one closes with general conclusions and recommendations. Environmental health risk assessors will find this volume a valuable resource

Legacy Risk Measure for Environmental Waste

International Nuclear Information System (INIS)

Eide, S. A.; Nitschke, R. L.

2002-01-01

The Idaho National Engineering and Environmental Laboratory (INEEL) is investigating the development of a comprehensive and quantitative risk model framework for environmental management activities at the site. Included are waste management programs (high-level waste, transuranic waste, low-level waste, mixed low-level waste, spent nuclear fuel, and special nuclear materials), major environmental restoration efforts, major decontamination and decommissioning projects, and planned long-term stewardship activities. Two basic types of risk estimates are included: risks from environmental management activities, and long-term legacy risks from wastes/materials. Both types of risks are estimated using the Environment, Safety, and Health Risk Assessment Program (ESHRAP) developed at the INEEL. Given these two types of risk calculations, the following evaluations can be performed: risk evaluation of an entire program (covering waste/material as it now exists through disposal or other e nd states); risk comparisons of alternative programs or activities; comparisons of risk benefit versus risk cost for activities or entire programs; ranking of programs or activities by risk; ranking of wastes/materials by risk; evaluation of site risk changes with time as activities progress; and integrated performance measurement using indicators such as injury/death and exposure rates. This paper discusses the definition and calculation of legacy risk measures and associated issues. The legacy risk measure is needed to support three of the seven types of evaluations listed above: comparisons of risk benefit versus risk cost, ranking of wastes/materials by risk, and evaluation of site risk changes with time

Environmental analysis burial of offsite low-level waste at SRP

International Nuclear Information System (INIS)

Poe, W.L.; Moyer, R.A.

1980-12-01

The environmental effects of receipt and burial of low-level naval waste generated at Department of Energy Laboratories are assessed in this environmental analysis. Through 1979, this low-level DOE waste was sent to the NRC-licensed burial ground operated by Chem-Nuclear Systems, Inc., at Barnwell, South Carolina. DOE announced on October 26, 1979, that DOE-generated low-level waste would no longer be buried at commercial waste burial sites. SRP was selected to receive the naval waste described in this analysis. Receipt and burial of these wastes will have a negligible effect on SRP's environment and increase only slightly the environmental effects of the SRP operations discussed in the EIS on SRP waste management operations. The environmental effects of burial of this waste at Chem-Nuclear Burial Ground or at the SRP Burial Ground are described in this environmental analysis to permit assessment of incremental effects caused by the decision to bury this naval waste in the SRP Burial Ground rather than in the Barnwell Burial Ground. The radiological effects from burial of this waste in either the SRP or Chem-Nuclear Burial Ground are very small when compared to those from natural background radiation or to the annual population dose commitment from operation of SRP. The environmental effects of burial at SRP to dose commitments normally received by the population surrounding SRP are compared

Report: environmental assessment of Darmstadt (Germany) municipal waste incineration plant.

Science.gov (United States)

Rimaityte, Ingrida; Denafas, Gintaras; Jager, Johannes

2007-04-01

The focus of this study was the emissions from waste incineration plants using Darmstadt (Germany) waste incineration plant as an example. In the study the emissions generated by incineration of the waste were considered using three different approaches. Initially the emissions from the waste incineration plant were assessed as part of the impact of waste management systems on the environment by using a Municipal Solid Waste Management System (MSWMS) assessment tool (also called: LCA-IWM assessment tool). This was followed by a comparison between the optimal waste incineration process and the real situation. Finally a comparison was made between the emissions from the incineration plant and the emissions from a vehicle.

Advanced mixed waste treatment project draft environmental impact statement

International Nuclear Information System (INIS)

1998-07-01

The AMWTP DEIS assesses the potential environmental impacts associated with four alternatives related to the construction and operation of a proposed waste treatment facility at the INEEL. Four alternatives were analyzed: The No Action Alternative, the Proposed Action, the Non-Thermal Treatment Alternative, and the Treatment and Storage Alternative. The proposed AMWTP facility would treat low-level mixed waste, alpha-contaminated low-level mixed waste, and transuranic waste in preparation for disposal. Transuranic waste would be disposed of at the Waste isolation Pilot Plant in New Mexico. Low-level mixed waste would be disposed of at an approval disposal facility depending on decisions to be based on DOE's Final Waste Management Programmatic Environmental Impact Statement. Evaluation of impacts on land use, socio-economics, cultural resources, aesthetic and scenic resources, geology, air resources, water resources, ecological resources, noise, traffic and transportation, occupational and public health and safety, INEEL services, and environmental justice were included in the assessment. The AMWTP DEIS identifies as the Preferred Alternative the Proposed Action, which is the construction and operation of the AMWTP facility

Environmental impact assessment of waste electronic and electric ...

African Journals Online (AJOL)

Wuhib.Z

Key words: Printed circuit boards (PCBs), e-waste, leaching tests, heavy metals, ..... Maximum leachability (in mg/kg) of metals versus leaching test methods (all tests were in triplicate). and c) ..... Environmental threats of discarded picture tubes.

Waste collection systems for recyclables: An environmental and economic assessment for the municipality of Aarhus (Denmark)

International Nuclear Information System (INIS)

Larsen, A.W.; Merrild, H.; Moller, J.; Christensen, T.H.

2010-01-01

Recycling of paper and glass from household waste is an integrated part of waste management in Denmark, however, increased recycling is a legislative target. The questions are: how much more can the recycling rate be increased through improvements of collection schemes when organisational and technical limitations are respected, and what will the environmental and economic consequences be? This was investigated in a case study of a municipal waste management system. Five scenarios with alternative collection systems for recyclables (paper, glass, metal and plastic packaging) were assessed by means of a life cycle assessment and an assessment of the municipality's costs. Kerbside collection would provide the highest recycling rate, 31% compared to 25% in the baseline scenario, but bring schemes with drop-off containers would also be a reasonable solution. Collection of recyclables at recycling centres was not recommendable because the recycling rate would decrease to 20%. In general, the results showed that enhancing recycling and avoiding incineration was recommendable because the environmental performance was improved in several impact categories. The municipal costs for collection and treatment of waste were reduced with increasing recycling, mainly because the high cost for incineration was avoided. However, solutions for mitigation of air pollution caused by increased collection and transport should be sought.

Informal e-waste recycling: environmental risk assessment of heavy metal contamination in Mandoli industrial area, Delhi, India.

Science.gov (United States)

Pradhan, Jatindra Kumar; Kumar, Sudhir

2014-01-01

Nowadays, e-waste is a major source of environmental problems and opportunities due to presence of hazardous elements and precious metals. This study was aimed to evaluate the pollution risk of heavy metal contamination by informal recycling of e-waste. Environmental risk assessment was determined using multivariate statistical analysis, index of geoaccumulation, enrichment factor, contamination factor, degree of contamination and pollution load index by analysing heavy metals in surface soils, plants and groundwater samples collected from and around informal recycling workshops in Mandoli industrial area, Delhi, India. Concentrations of heavy metals like As (17.08 mg/kg), Cd (1.29 mg/kg), Cu (115.50 mg/kg), Pb (2,645.31 mg/kg), Se (12.67 mg/kg) and Zn (776.84 mg/kg) were higher in surface soils of e-waste recycling areas compared to those in reference site. Level exceeded the values suggested by the US Environmental Protection Agency (EPA). High accumulations of heavy metals were also observed in the native plant samples (Cynodon dactylon) of e-waste recycling areas. The groundwater samples collected form recycling area had high heavy metal concentrations as compared to permissible limit of Indian Standards and maximum allowable limit of WHO guidelines for drinking water. Multivariate analysis and risk assessment studies based on total metal content explains the clear-cut differences among sampling sites and a strong evidence of heavy metal pollution because of informal recycling of e-waste. This study put forward that prolonged informal recycling of e-waste may accumulate high concentration of heavy metals in surface soils, plants and groundwater, which will be a matter of concern for both environmental and occupational hazards. This warrants an immediate need of remedial measures to reduce the heavy metal contamination of e-waste recycling sites.

Future management of hazardous wastes generated at Brookhaven National Laboratory, Upton, New York. Environmental assessment

International Nuclear Information System (INIS)

1994-09-01

This document assesses the potential environmental impacts of a variety of alternatives which could provide a Resource Conservation and Recovery Act (RCRA) permitted waste packaging and storage facility that would handle all hazardous, radioactive, and mixed wastes generated at Brookhaven National Laboratory (BNL) and would operate in full compliance with all federal, state, and local laws and regulations. Location of the existing Hazardous Waste Management Facility (HWMF) with respect to ground water and the site boundary, technical and capacity limitations, inadequate utilities, and required remediation of the area make the existing facility environmentally unacceptable for long term continued use. This Environmental Assessment (EA) describes the need for action by the Department of Energy (DOE). It evaluates the alternatives for fulfilling that need, including the alternative preferred by DOE, a no-action alternative, and other reasonable alternatives. The EA provides a general description of BNL and the existing environment at the current HWMF and alternative locations considered for a new Waste Management Facility (WMF). Finally, the EA describes the potential environmental impacts of the alternatives considered. The preferred alternative, also identified as Alternative D, would be to construct and operate a new WMF on land formerly occupied by barracks during Camp Upton operations, in an area north of Building 830 and the High Flux Beam Reactor/Alternating Gradient Synchrotron (AGS) recharge basins, east of North Railroad Street, and south of East Fifth Avenue. The purpose of this new facility would be to move all storage and transfer activities inside buildings and on paved and curbed areas, consolidate facilities to improve operations management, and provide improved protection of the environment

Environmental exposure assessment framework for nanoparticles in solid waste

DEFF Research Database (Denmark)

Boldrin, Alessio; Hansen, Steffen Foss; Baun, Anders

2014-01-01

Information related to the potential environmental exposure of engineered nanomaterials (ENMs) in the solid waste management phase is extremely scarce. In this paper, we define nanowaste as separately collected or collectable waste materials which are or contain ENMs, and we present a five...... transformation during waste treatment processes, (2) mechanisms for the release of ENMs, (3) the quantification of nanowaste amounts at the regional scale, (4) a definition of acceptable limit values for exposure to ENMs from nanowaste and (5) the reporting of nanowaste generation data....

A bi-level environmental impact assessment framework for comparing construction and demolition waste management strategies.

Science.gov (United States)

Yazdanbakhsh, Ardavan

2018-04-27

Several pioneering life cycle assessment (LCA) studies have been conducted in the past to assess the environmental impact of specific methods for managing mineral construction and demolition waste (MCDW), such as recycling the waste for use in concrete. Those studies focus on comparing the use of recycled MCDW and that of virgin components to produce materials or systems that serve specified functions. Often, the approaches adopted by the studies do not account for the potential environmental consequence of avoiding the existing or alternative waste management practices. The present work focuses on how product systems need to be defined in recycling LCA studies and what processes need to be within the system boundaries. A bi-level LCA framework is presented for modelling alternative waste management approaches in which the impacts are measured and compared at two scales of strategy and decision-making. Different functional units are defined for each level, all of which correspond to the same flow of MCDW in a cascade of product systems. For the sole purpose of demonstrating how the framework is implemented an illustrative example is presented, based on real data and a number of simplifying assumptions, which compares the impacts of a number of potential MCDW management strategies in New York City. Copyright © 2018 Elsevier Ltd. All rights reserved.

Environmental contaminants: assessment and control

National Research Council Canada - National Science Library

Vallero, Daniel A

2004-01-01

... Understanding Policy by Understanding Science Connections and Interrelationships of Environmental Science Environmental Assessment and Intervention Engineering Technical Note: Cleaning up a Hazardous Waste Site Social Aspects of Environmental Science Introduction to Environmental Policy The National Environmental Policy Act Issues in Environmental Science: Co...

Disposal and environmental assessment of solid waste and radioactive waste

International Nuclear Information System (INIS)

Tan Chenglong

2000-01-01

Along with the development of economic construction, the industrial and agricultural production, military and scientific activities of human being, large amounts of solid and radioactive wastes have been produced, causing serious pollution of ecologic environments and living space of human being itself. To assess and administer the solid and radioactive wastes in geologic-ecologic environments are duty-bound responsibilities of modern geologists and the focus of recent geo-ecologic work

Environmental assessment of waste management in Greenland: current practice and potential future developments

DEFF Research Database (Denmark)

Eisted, Rasmus; Christensen, Thomas Højlund

2013-01-01

) for a system serving 56 000 inhabitants), but significant environmental loads are caused by air emissions from the incinerators and leachate from the landfills. Several alternative management scenarios were modelled and results show that increased use of incineration, full utilization of the heat production...... for district heating and separation of hazardous waste probably could improve Greenland’s waste management system. Segregation of recyclable materials as paper, cardboard and biowaste will do little to environmentally improve the waste management system due to loss of energy recovery from incineration...... and the long transport of the recyclables to markets. Export of waste to Denmark for incineration at modern waste incinerators with advanced flue gas cleaning could also be considered as a means to achieve better environmental performance of the waste management system....

Impact assessment of waste management options in Singapore.

Science.gov (United States)

Tan, Reginald B H; Khoo, Hsien H

2006-03-01

This paper describes the application of life cycle assessment for evaluating various waste management options in Singapore, a small-island city state. The impact assessment method by SimaPro is carried out for comparing the potential environmental impacts of waste treatment options including landfilling, incineration, recycling, and composting. The inventory data include gases and leachate from landfills, air emissions and energy recovery from incinerators, energy (and emission) savings from recycling, composting gases, and transport pollution. The impact assessment results for climate change, acidification, and ecotoxicity show that the incineration of materials imposes considerable harm to both human health and the environment, especially for the burning of plastics, paper/cardboard, and ferrous metals. The results also show that, although some amount of energy can be derived from the incineration of wastes, these benefits are outweighed by the air pollution (heavy metals and dioxins/furans) that incinerators produce. For Singapore, landfill gases and leachate generate minimal environmental damage because of the nation's policy to landfill only 10% of the total disposed wastes. Land transportation and separation of waste materials also pose minimal environmental damage. However, sea transportation to the landfill could contribute significantly to acidification because of the emissions of sulfur oxides and nitrogen oxides from barges. The composting of horticultural wastes hardly imposes any environmental damage. Out of all the waste strategies, the recycling of wastes offers the best solution for environmental protection and improved human health for the nation. Significant emission savings can be realized through recycling.

Report on the evaluation under the Act No 24/2006 of Coll. Environmental Impact Assessment Law Extension of National Radioactive Waste Repository in Mochovce for disposal low-level radioactive waste and construction of very low-level radioactive waste repository

International Nuclear Information System (INIS)

Hanusik, V.; Moravek, J.; Kusovska, Z.

2011-01-01

The report elaborated assessment of the environmental impact of extension of the National Radioactive Waste Repository in Mochovce for disposal of low and intermediate level radioactive wastes. Within this repository also the premises for very low level radioactive waste deposition should be built. The assessment report was prepared according to the Act no. 24/2006 Coll, as amended 'On the assessment of environmental impacts' Annex No. 11 upon The scope of assessment issued by the competent authority on the basis of assessment of Intent for this action. The report was prepared in VUJE, Inc. Trnava for Nuclear and Decommissioning Company, Inc. Bratislava (JAVYS).

Nutrition in the Bin: A Nutritional and Environmental Assessment of Food Wasted in the UK

Directory of Open Access Journals (Sweden)

Karen A. Cooper

2018-03-01

Full Text Available The UK currently has the most detailed, directly measured data for food wasted in the home. This includes information on the exact types of food wasted. These data allow calculation of the nutrients within that waste, as well as its environmental impact. The results progress the conversation beyond how much food is wasted or its energy content; it permits the implications for nutrition and sustainability to be assessed in detail. Data for UK household food waste were expressed as an average waste per capita for each type of food. Each food type was matched with an item (or group of items from the UK Composition of Foods (7th Ed. The level of nutrients wasted was compared to UK Reference Nutrient Intakes (RNIs for adult women (19–50 years, used as a proxy for general population requirements. The data were normalized into “nutrient days” wasted per capita per year, then into the number of complete diet days (for 21 nutrients plus energy. Results show that approximately 42 daily diets were discarded per capita per year. By individual nutrient, the highest losses were vitamin B12, vitamin C, and thiamin (160, 140, and 130 nutrient days/capita/year, respectively. For protein, dietary energy and carbohydrates, 88, 59, and 53 nutrient days/capita/year, respectively, were lost. Substantial losses were also found for under-consumed nutrients in the UK: calcium, which was mostly lost via bakery (27% and dairy/eggs (27%. Food folate was mainly lost through fresh vegetables/salads (40% and bakery (18%, as was dietary fiber (31 and 29%, respectively. Environmental impacts were distributed over the food groups, with wasted meat and fish the single largest contribution. For all environmental impacts studied, the largest contribution came from agricultural production. This paper shows that there are areas where interventions preventing food waste and promoting healthy eating could work together (e.g., encouraging consumption of vegetables or tackling

Nutrition in the Bin: A Nutritional and Environmental Assessment of Food Wasted in the UK.

Science.gov (United States)

Cooper, Karen A; Quested, Tom E; Lanctuit, Helene; Zimmermann, Diane; Espinoza-Orias, Namy; Roulin, Anne

2018-01-01

The UK currently has the most detailed, directly measured data for food wasted in the home. This includes information on the exact types of food wasted. These data allow calculation of the nutrients within that waste, as well as its environmental impact. The results progress the conversation beyond how much food is wasted or its energy content; it permits the implications for nutrition and sustainability to be assessed in detail. Data for UK household food waste were expressed as an average waste per capita for each type of food. Each food type was matched with an item (or group of items) from the UK Composition of Foods (7th Ed). The level of nutrients wasted was compared to UK Reference Nutrient Intakes (RNIs) for adult women (19-50 years, used as a proxy for general population requirements). The data were normalized into "nutrient days" wasted per capita per year, then into the number of complete diet days (for 21 nutrients plus energy). Results show that approximately 42 daily diets were discarded per capita per year. By individual nutrient, the highest losses were vitamin B 12 , vitamin C, and thiamin (160, 140, and 130 nutrient days/capita/year, respectively). For protein, dietary energy and carbohydrates, 88, 59, and 53 nutrient days/capita/year, respectively, were lost. Substantial losses were also found for under-consumed nutrients in the UK: calcium, which was mostly lost via bakery (27%) and dairy/eggs (27%). Food folate was mainly lost through fresh vegetables/salads (40%) and bakery (18%), as was dietary fiber (31 and 29%, respectively). Environmental impacts were distributed over the food groups, with wasted meat and fish the single largest contribution. For all environmental impacts studied, the largest contribution came from agricultural production. This paper shows that there are areas where interventions preventing food waste and promoting healthy eating could work together (e.g., encouraging consumption of vegetables or tackling overbuying

Cataract surgery and environmental sustainability: Waste and lifecycle assessment of phacoemulsification at a private healthcare facility.

Science.gov (United States)

Thiel, Cassandra L; Schehlein, Emily; Ravilla, Thulasiraj; Ravindran, R D; Robin, Alan L; Saeedi, Osamah J; Schuman, Joel S; Venkatesh, Rengaraj

2017-11-01

To measure the waste generation and lifecycle environmental emissions from cataract surgery via phacoemulsification in a recognized resource-efficient setting. Two tertiary care centers of the Aravind Eye Care System in southern India. Observational case series. Manual waste audits, purchasing data, and interviews with Aravind staff were used in a hybrid environmental lifecycle assessment framework to quantify the environmental emissions associated with cataract surgery. Kilograms of solid waste generated and midpoint emissions in a variety of impact categories (eg, kilograms of carbon dioxide equivalents). Aravind generates 250 grams of waste per phacoemulsification and nearly 6 kilograms of carbon dioxide-equivalents in greenhouse gases. This is approximately 5% of the United Kingdom's phaco carbon footprint with comparable outcomes. A majority of Aravind's lifecycle environmental emissions occur in the sterilization process of reusable instruments because their surgical system uses largely reusable instruments and materials. Electricity use in the operating room and the Central Sterile Services Department (CSSD) accounts for 10% to 25% of most environmental emissions. Surgical systems in most developed countries and, in particular their use of materials, are unsustainable. Results show that ophthalmologists and other medical specialists can reduce material use and emissions in medical procedures using the system described here. Copyright © 2017 ASCRS and ESCRS. Published by Elsevier Inc. All rights reserved.

Environmental assessment for liquid waste treatment at the Nevada Test Site, Nye County, Nevada

International Nuclear Information System (INIS)

1997-01-01

This environmental assessment (EA) examines the potential impacts to the environment from treatment of low-level radioactive liquid and low-level mixed liquid and semi-solid wastes generated at the Nevada Test Site (NTS). The potential impacts of the proposed action and alternative actions are discussed herein in accordance with the National Environmental Policy Act (NEPA) of 1969, as amended in Title 42 U.S.C. (4321), and the US Department of Energy (DOE) policies and procedures set forth in Title 10 Code of Federal Regulations (CFR) Part 1021 and DOE Order 451.1, ''NEPA Compliance Program.'' The potential environmental impacts of the proposed action, construction and operation of a centralized liquid waste treatment facility, were addressed in the Final Environmental Impact Statement for the Nevada Test Site and Off-Site Locations in the State of Nevada. However, DOE is reevaluating the need for a centralized facility and is considering other alternative treatment options. This EA retains a centralized treatment facility as the proposed action but also considers other feasible alternatives

DOE model conference on waste management and environmental restoration

International Nuclear Information System (INIS)

1990-01-01

Reports dealing with current topics in waste management and environmental restoration were presented at this conference in six sessions. Session 1 covered the ''Hot Topics'' including regulations and risk assessment. Session 2 dealt with waste reduction and minimization; session 3 dealt with waste treatment and disposal. Session 4 covered site characterization and analysis. Environmental restoration and associated technologies wee discussed in session 5 and 6. Individual papers have been cataloged separately

Environmental risk assessment of the use of different organic wastes as soil amendments

Science.gov (United States)

Alvarenga, Paula; Palma, Patrícia; Mourinha, Clarisse; Farto, Márcia; Cunha-Queda, Ana Cristina; Natal-da-Luz, Tiago; Sousa, José Paulo

2013-04-01

The use of organic wastes in agriculture is considered a way of maintaining or restoring the quality of soils, enlarging the slow cycling soil organic carbon pool. However, a wide variety of undesired substances, such as potentially trace elements and organic contaminants, can have adverse effects on the environment. That fact was highlighted by the Proposal for a Soil Framework Directive, which recognized that "soil degradation or soil improvements have a major impact on other areas, (…) such as surface waters and groundwater, human health, climate change, protection of nature and biodiversity, and food safety". Taking that into account, the research project "ResOrgRisk" aims to assess the environmental risk involved in the use of different organic wastes as soil amendments, evidencing their benefits and constraints, and defining the most suitable tests to reach such assessment. The organic wastes selected for this purpose were: sewage sludge, limed, not limed, and co-composted with agricultural wastes, agro-industrial sludge, mixed municipal solid waste compost, compost produced from organic farming residues, and pig slurry digestate. Whereas threshold values for heavy metals in sludge used for agriculture have been set by the European Commission, actually there is no definitive European legislation for organic contaminants. Guide values for some organic contaminants (e.g. polychlorinated biphenyls - PCBs, and polycyclic aromatic hydrocarbons - PAHs) have been adopted at national level by many European countries, such as Portugal. These values should be taken into account when assessing the risk involved in the use of organic wastes as soil amendments. However, chemical analysis of organic waste often gives scarce information because it does not include possible interactions between chemicals. Furthermore, an exhaustive identification and quantification of all substances is impractical. In this study, ecotoxicological tests (comprising solid and aquatic phases

Tank 241-C-106 past-practice sluicing waste retrieval, Hanford Site, Richland, Washington. Environmental Assessment

International Nuclear Information System (INIS)

1995-02-01

The US Department of Energy (DOE) needs to take action to eliminate safety concerns with storage of the high-heat waste in Tank 241-C-106 (Tank C-106), and demonstrate a tank waste retrieval technology. This Environmental Assessment (EA) was prepared to analyze the potential impacts associated with the proposed action, past-practice sluicing of Tank C-106, an underground single-shell tank (SST). Past-practice sluicing is defined as the mode of waste retrieval used extensively in the past at the Hanford Site on the large underground waste tanks, and involves introducing a high-volume, low-pressure stream of liquid to mobilize sludge waste prior to pumping. It is proposed to retrieve the waste from Tank C-106 because this waste is classified not only as transuranic and high-level, but also as high-heat, which is caused by the radioactive decay of strontium. This waste characteristic has led DOE to place Tank C-106 on the safety ''Watchlist.''

An environmental assessment of electricity production from slaughterhouse residues. Linking urban, industrial and waste management systems

International Nuclear Information System (INIS)

Santagata, R.; Ripa, M.; Ulgiati, S.

2017-01-01

Highlights: • Animal by-products use for electricity generation is investigated as a case-study. • Different methodological approaches to deal with by-products are explored in LCA. • Adopting a holistic perspective is crucial to achieve a circular economy framework. - Abstract: The food processing industry continues to grow, generating large amount of organically rich waste flows per year: these processors face significant economic and environmental pressures for appropriate conversion and disposal of these waste flows. Solid waste disposal problems, mostly in highly urbanized environments, energy shortages (primarily oil) and/or high petroleum prices, as well as environmental issues such as the shrinking landfill capacity, can all be addressed by converting waste material into useful and saleable products. This paper brings to the attention a possible strategy in order to meet the general EU directives concerning the residues utilization and percentage contribution for the total energy consumption by 2020, by evaluating the use of animal by-products (category 3, as defined in the directive 2002/1774/EC) for energy purposes. Slaughterhouse waste represents an important potential source of renewable energy: on average, 40–50% of a live animal is waste, with a potential energy content close to diesel fuel. Treatment of animal waste from slaughterhouse and the subsequent conversion to electricity is investigated as a case study in the Campania Region (Italy): the animal waste undergoes a rendering process, to separate a protein-rich fraction useful for animal meal production and a fat-rich fraction, to be combusted in a diesel engine for power and heat generation (CHP). An environmental assessment of the entire process is performed by means of LCA, providing a quantitative understanding of the plant processing. The study aims to understand to what extent electricity production from animal fat is environmentally sound and if there are steps and/or components

DOE model conference on waste management and environmental restoration

Energy Technology Data Exchange (ETDEWEB)

1990-01-01

Reports dealing with current topics in waste management and environmental restoration were presented at this conference in six sessions. Session 1 covered the Hot Topics'' including regulations and risk assessment. Session 2 dealt with waste reduction and minimization; session 3 dealt with waste treatment and disposal. Session 4 covered site characterization and analysis. Environmental restoration and associated technologies wee discussed in session 5 and 6. Individual papers have been cataloged separately.

Environmental issues and wastes

International Nuclear Information System (INIS)

Mitamura, Hisayoshi; Banba, Tsunetaka; Maeda, Toshikatsu; Ishiyama, Takashi

1999-08-01

All countries in the world are concerned about environmental issues because of their global effects. Developed industrial nations are also confronted with waste issues accompanied by mass production, mass consumption, and mass dump. We have reviewed books and reports to obtain a preliminary knowledge and to understand the trend of technology development before we start R and D for 'environmental monitoring, and environmental remediation and protection'. We lay great emphasis on municipal and industrial wastes in environmental issues and summarize the history of the earth, innovative environmental approaches in advanced nations, waste issues in Japan, and examples of technology development for environmental remediation and protection. (author)

Progress in reducing the environmental impacts of offshore drilling wastes

International Nuclear Information System (INIS)

Flemming, D; Candler, J.E.

2002-01-01

Full text:Over the past several years, great progress has been made in understanding and reducing the environmental impacts of offshore drilling wastes. Our understanding of sea floor impacts has been helped along by new environmental assessment tools such us computer modeling of sea floor deposition of drilling discharges, sediment profile imaging, and in situ sediment toxicity bioassays. To further reduce environmental impacts, new pollution prevention technologies have been developed that can shrink the environmental footprint of offshore drilling. These technologies reduce the total amount of drilling wastes discharged and include cuttings dryers and centrifuges that can reduce the drilling fluid content of drill cuttings to below 10 percent. In conclusion, the oil and gas industry is adopting more environmentally compatible drilling fluids, new environmental assessment tools and pollution prevention technologies that dramatically reduce the amount of drilling wastes discharged. Together, all of these elements have the potential to reduce environmental impacts of offshore drilling

Final environmental assessment: TRU waste drum staging building, Technical Area 55, Los Alamos National Laboratory

International Nuclear Information System (INIS)

1996-01-01

Much of the US Department of Energy's (DOE's) research on plutonium metallurgy and plutonium processing is performed at Los Alamos National Laboratory (LANL), in Los Alamos, New Mexico. LANL's main facility for plutonium research is the Plutonium Facility, also referred to as Technical Area 55 (TA-55). The main laboratory building for plutonium work within the Plutonium Facility (TA-55) is the Plutonium Facility Building 4, or PF-4. This Environmental Assessment (EA) analyzes the potential environmental effects that would be expected to occur if DOE were to stage sealed containers of transuranic (TRU) and TRU mixed waste in a support building at the Plutonium Facility (TA-55) that is adjacent to PF-4. At present, the waste containers are staged in the basement of PF-4. The proposed project is to convert an existing support structure (Building 185), a prefabricated metal building on a concrete foundation, and operate it as a temporary staging facility for sealed containers of solid TRU and TRU mixed waste. The TRU and TRU mixed wastes would be contained in sealed 55-gallon drums and standard waste boxes as they await approval to be transported to TA-54. The containers would then be transported to a longer term TRU waste storage area at TA-54. The TRU wastes are generated from plutonium operations carried out in PF-4. The drum staging building would also be used to store and prepare for use new, empty TRU waste containers

Risk assessment for the transportation of hazardous waste and hazardous waste components of low-level mixed waste and transuranic waste for the US Department of Energy waste management programmatic environmental impact statement

International Nuclear Information System (INIS)

Lazaro, M.A.; Policastro, A.J.; Hartmann, H.M.; Chang, Y.S.

1996-12-01

This report, a supplement to Appendix E (Transportation Risk) of the U.S. Department of Energy Waste Management Programmatic Environmental Impact Statement (WM PEIS), provides additional information supporting the accident data for chemical risk assessment and health risk methodology described in that appendix (Part II) and presents the uncertainty analysis and on-site risk calculations. This report focuses on hazardous material truck accident rates, release probabilities, and release quantities; provides the toxicological values derived for each hazardous chemical assessed in the WM PEIS and further details on the derivation of health criteria; describes the method used in the transportation risk assessments to address potential additivity of health effects from simultaneous exposure to several chemicals and the method used to address transportation risks for maximally exposed individuals; presents an expanded discussion of the uncertainty associated with transportation risk calculations; and includes the results of the on-site transportation risk analysis. In addition, two addenda are provided to detail the risk assessments conducted for the hazardous components of low-level mixed waste (Addendum I) and transuranic waste (Addendum II)

The Approach to Assessing Environmental, Social and Economic Effects of Radioactive Waste Management in the United Kingdom

Energy Technology Data Exchange (ETDEWEB)

Grinham, Russell (Nuclear Decommissioning Authority - Radioactive Waste Management Directorate, Harwell, Didcot, Oxfordshire, OX11 0RH (United Kingdom))

2009-12-15

The Nuclear Decommissioning Authority (NDA) is a non-departmental public body, which began operation in April 2005 with a remit to secure the decommissioning and clean-up of the UK's civil public sector nuclear sites. This remit was widened when the Government announced on 25 October 2006 that, following recommendations from the Committee on Radioactive Waste Management (CoRWM), higher activity wastes will be managed in the long-term through geological disposal. Government also announced that it would be giving the NDA the responsibility for planning and implementing geological disposal. A new directorate within the NDA was created, the Radioactive Waste Management Directorate (RWMD), to manage this new remit. RWMD's mission is to deliver geological disposal and provide radioactive waste management solutions. To achieve this mission, RWMD will: Engage with national and local governments and communities to identify a geological disposal facility site; Develop the specification, design, safety case and environmental and sustainability assessments for the disposal system and obtain regulatory support; In conjunction with waste producers, identify and deliver solutions to optimise the management of higher activity waste; Develop and maintain an effective organisation and secure resources to deliver the geological disposal facility programme; Obtain and maintain stakeholder support for our activities; Deliver a focused RandD programme to support geological disposal and optimised packaging solutions; and Seek sustainable, innovative and cost effective solutions that have public support and are in the best interest of the UK. The Government White Paper placed a requirement on the NDA to assess potential social, environmental and economic impacts of implementing a geological disposal facility using SA, SEA and EIA. This paper outlines the NDA's approach to achieving this requirement. Key elements of the approach are: A staged approach linked to the MRWS site

The Approach to Assessing Environmental, Social and Economic Effects of Radioactive Waste Management in the United Kingdom

International Nuclear Information System (INIS)

Grinham, Russell

2009-12-01

The Nuclear Decommissioning Authority (NDA) is a non-departmental public body, which began operation in April 2005 with a remit to secure the decommissioning and clean-up of the UK's civil public sector nuclear sites. This remit was widened when the Government announced on 25 October 2006 that, following recommendations from the Committee on Radioactive Waste Management (CoRWM), higher activity wastes will be managed in the long-term through geological disposal. Government also announced that it would be giving the NDA the responsibility for planning and implementing geological disposal. A new directorate within the NDA was created, the Radioactive Waste Management Directorate (RWMD), to manage this new remit. RWMD's mission is to deliver geological disposal and provide radioactive waste management solutions. To achieve this mission, RWMD will: Engage with national and local governments and communities to identify a geological disposal facility site; Develop the specification, design, safety case and environmental and sustainability assessments for the disposal system and obtain regulatory support; In conjunction with waste producers, identify and deliver solutions to optimise the management of higher activity waste; Develop and maintain an effective organisation and secure resources to deliver the geological disposal facility programme; Obtain and maintain stakeholder support for our activities; Deliver a focused RandD programme to support geological disposal and optimised packaging solutions; and Seek sustainable, innovative and cost effective solutions that have public support and are in the best interest of the UK. The Government White Paper placed a requirement on the NDA to assess potential social, environmental and economic impacts of implementing a geological disposal facility using SA, SEA and EIA. This paper outlines the NDA's approach to achieving this requirement. Key elements of the approach are: A staged approach linked to the MRWS site selection

Importance of waste composition for Life Cycle Assessment of waste management solutions

DEFF Research Database (Denmark)

Bisinella, Valentina; Götze, Ramona; Conradsen, Knut

2017-01-01

The composition of waste materials has fundamental influence on environmental emissions associated with waste treatment, recycling and disposal, and may play an important role also for the Life Cycle Assessment (LCA) of waste management solutions. However, very few assessments include effects...... of the waste composition and waste LCAs often rely on poorly justified data from secondary sources. This study systematically quantifiesy the influence and uncertainty on LCA results associated with selection of waste composition data. Three archetypal waste management scenarios were modelled with the waste...... LCA model EASETECH based on detailed waste composition data from the literature. The influence from waste composition data on the LCA results was quantified with a step-wise Global Sensitivity Analysis (GSA) approach involving contribution, sensitivity, uncertainty and discernibility analyses...

Waste minimization assessment for a manufacturer of baseball bats and golf clubs. Environmental research brief

Energy Technology Data Exchange (ETDEWEB)

Fleischman, M.; Kirsch, F.W.; Maginn, J.C.

1993-09-01

The U.S. Environmental Protection Agency (EPA) has funded a pilot project to assist small and medium-size manufacturers who want to minimize their generation of waste but who lack the expertise to do so. Waste Minimization Assessment Center (WMAC) at the University of Louisville performed an assessment at a plant manufacturing baseball bats and golf clubs -- approximately 1,500,000 bats/yr and 550,000 golf clubs/yr. To make the bats, wood billets are oven-dried and machined to a standard dimension. After sanding they are branded and finished. The golf clubs are made by finishing and assembling purchased heads and shafts. The team's report detailing findings and recommendations, indicated that the most waste, other than rinse water discharged to the publicly owned treatment works (POTW) and wood turnings which are sold, consists of scrap cardboard and paper from the shop and offices, and that the greatest savings, including new income, could be obtained by segregating the cardboard and paper wastes for sale to a local recycler.

Risk assessment for the transportation of hazardous waste and hazardous waste components of low-level mixed waste and transuranic waste for the U.S. Department of Energy waste management programmatic environmental impact statement

International Nuclear Information System (INIS)

Lazaro, M.A.; Policastro, A.J.; Hartmann, H.M.

1995-04-01

This report, a supplement to Appendix E (Transportation Risk) of the U.S. Department of Energy Waste Management Programmatic Environmental Impact Statement (WM PEIS), provides additional information supporting the accident data for chemical risk assessment and health risk methodology described in that appendix (Part II), as well as providing the uncertainty analysis and on-site risk calculations. This report focuses on hazardous material truck accident rates, release probabilities, and release quantities; provides the toxicological values derived for each hazardous chemical assessed in the WM PEIS and further details on the derivation of health criteria; describes the method used in the transportation risk assessments to address potential additivity of health effects from simultaneous exposure to several chemicals and the method used to address transportation risks for maximally exposed individuals; presents an expanded discussion of the uncertainty associated with transportation risk calculations; and includes the results of the on-site transportation risk analysis. In addition, two addenda are provided to detail the risk assessments conducted for the hazardous components of low-level mixed waste (Addendum I) and transuranic waste (Addendum II)

Waste management programmatic environmental impact statement methodology for estimating human health risks

International Nuclear Information System (INIS)

Bergenback, B.; Blaylock, B.P.; Legg, J.L.

1995-05-01

The US Department of Energy (DOE) has produced large quantities of radioactive and hazardous waste during years of nuclear weapons production. As a result, a large number of sites across the DOE Complex have become chemically and/or radiologically contaminated. In 1990, the Secretary of Energy charged the DOE Office of Environmental Restoration and Waste management (EM) with the task of preparing a Programmatic Environmental Impact Statement (PEIS). The PEIS should identify and assess the potential environmental impacts of implementing several integrated Environmental Restoration (ER) and Waste Management (WM) alternatives. The determination and integration of appropriate remediation activities and sound waste management practices is vital for ensuring the diminution of adverse human health impacts during site cleanup and waste management programs. This report documents the PEIS risk assessment methodology used to evaluate human health risks posed by WM activities. The methodology presents a programmatic cradle to grave risk assessment for EM program activities. A unit dose approach is used to estimate risks posed by WM activities and is the subject of this document

Northeast Regional environmental impact study: Waste disposal technical report

Science.gov (United States)

Saguinsin, J. L. S.

1981-04-01

The potential for cumulative and interactive environmental impacts associated with the conversion of multiple generating stations in the Northeast is assessed. The estimated quantities and composition of wastes resulting from coal conversion, including ash and SO2 scrubber sludge, are presented. Regulations governing the use of ash and scrubber sludge are identified. Currently available waste disposal schemes are described. The location, capacity, and projected life of present and potential disposal sites in the region are identified. Waste disposal problems, both hazardous and nonhazardous, are evaluated. Environmental regulations within the region as they pertain to coal conversion and as they affect the choice of conversion alternatives are discussed. A regional waste management strategy for solid waste disposal is developed.

Environmental assessment, finding of no significant impact, and response to comments. Radioactive waste storage

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-04-01

The Department of Energy`s (DOE) Rocky Flats Environmental Technology Site (the Site), formerly known as the Rocky Flats Plant, has generated radioactive, hazardous, and mixed waste (waste with both radioactive and hazardous constituents) since it began operations in 1952. Such wastes were the byproducts of the Site`s original mission to produce nuclear weapons components. Since 1989, when weapons component production ceased, waste has been generated as a result of the Site`s new mission of environmental restoration and deactivation, decontamination and decommissioning (D&D) of buildings. It is anticipated that the existing onsite waste storage capacity, which meets the criteria for low-level waste (LL), low-level mixed waste (LLM), transuranic (TRU) waste, and TRU mixed waste (TRUM) would be completely filled in early 1997. At that time, either waste generating activities must cease, waste must be shipped offsite, or new waste storage capacity must be developed.

Environmental assessment, finding of no significant impact, and response to comments. Radioactive waste storage

International Nuclear Information System (INIS)

1996-04-01

The Department of Energy's (DOE) Rocky Flats Environmental Technology Site (the Site), formerly known as the Rocky Flats Plant, has generated radioactive, hazardous, and mixed waste (waste with both radioactive and hazardous constituents) since it began operations in 1952. Such wastes were the byproducts of the Site's original mission to produce nuclear weapons components. Since 1989, when weapons component production ceased, waste has been generated as a result of the Site's new mission of environmental restoration and deactivation, decontamination and decommissioning (D ampersand D) of buildings. It is anticipated that the existing onsite waste storage capacity, which meets the criteria for low-level waste (LL), low-level mixed waste (LLM), transuranic (TRU) waste, and TRU mixed waste (TRUM) would be completely filled in early 1997. At that time, either waste generating activities must cease, waste must be shipped offsite, or new waste storage capacity must be developed

Modular life cycle assessment of municipal solid waste management.

Science.gov (United States)

Haupt, M; Kägi, T; Hellweg, S

2018-05-31

Life cycle assessment (LCA) is commonly applied to examine the environmental performance of waste management systems. The system boundaries are, however, often limited to either one tonne of material or to specific waste treatments and are, therefore, lacking a systems perspective. Here, a framework is proposed to assess complete waste management systems based on actual waste flows, assessed with a detailed material flow analysis (MFA) in a modular MFA/LCA approach. The transformation of the MFA into a product-process-matrix facilitates a direct link between MFA and LCA, therefore allowing for the assessment of variations in flows. To allow for an up-to-date and geographically specific assessment, 190 LCA modules were set up based on primary industrial data and the ecoinvent database. The LCA modules show where there have been improvements in different recycling processes over the past years (e.g. for paper recycling) and highlight that, from an environmental perspective, closed-loop recycling is not always preferable to open-loop recycling. In a case study, the Swiss municipal solid waste management system, of which there is already a detailed MFA, was modeled using the new LCA modules and applying the modular MFA/LCA approach. Five different mass flow distribution scenarios for the Swiss municipal solid waste management system were assessed to show the environmental impact of political measures and to test the sensitivity of the results to key parameters. The results of the case study highlight the importance of the dominant fractions in the overall environmental impacts assessment; while the metal fraction has the highest impact on a per kilogram basis, paper, cardboard, glass and mixed municipal solid waste were found to dominate the environmental impacts of the Swiss waste management system due to their mass. The scenarios also highlight the importance of the energy efficiency of municipal solid waste incineration plants and the credits from material

Assessing the environmental impact of energy production from hydrochar generated via hydrothermal carbonization of food wastes.

Science.gov (United States)

Berge, Nicole D; Li, Liang; Flora, Joseph R V; Ro, Kyoung S

2015-09-01

Although there are numerous studies suggesting hydrothermal carbonization is an environmentally advantageous process for transformation of wastes to value-added products, a systems level evaluation of the environmental impacts associated with hydrothermal carbonization and subsequent hydrochar combustion has not been conducted. The specific objectives of this work are to use a life cycle assessment approach to evaluate the environmental impacts associated with the HTC of food wastes and the subsequent combustion of the generated solid product (hydrochar) for energy production, and to understand how parameters and/or components associated with food waste carbonization and subsequent hydrochar combustion influence system environmental impact. Results from this analysis indicate that HTC process water emissions and hydrochar combustion most significantly influence system environmental impact, with a net negative GWP impact resulting for all evaluated substituted energy-sources except biomass. These results illustrate the importance of electricity production from hydrochar particularly when it is used to offset coal-based energy sources. HTC process water emissions result in a net impact to the environment, indicating a need for developing appropriate management strategies. Results from this analysis also highlight a need for additional exploration of liquid and gas-phase composition, a better understanding of how changes in carbonization conditions (e.g., reaction time and temperature) influence metal and nutrient fate, and the exploration of liquid-phase treatment. Copyright © 2015 Elsevier Ltd. All rights reserved.

Environmental development plan. LWR commercial waste management

International Nuclear Information System (INIS)

1980-08-01

This Environmental Development Plan (EDP) identifies the planning and managerial requirements and schedules needed to evaluate and assess the environmental, health and safety (EH and S) aspects of the Commercial Waste Management Program (CWM). Environment is defined in its broadest sense to include environmental, health (occupational and public), safety, socioeconomic, legal and institutional aspects. This plan addresses certain present and potential Federal responsibilities for the storage, treatment, transfer and disposal of radioactive waste materials produced by the nuclear power industry. The handling and disposal of LWR spent fuel and processed high-level waste (in the event reprocessing occurs) are included in this plan. Defense waste management activities, which are addressed in detail in a separate EDP, are considered only to the extent that such activities are common to the commercial waste management program. This EDP addresses three principal elements associated with the disposal of radioactive waste materials from the commercial nuclear power industry, namely Terminal Isolation Research and Development, Spent Fuel Storage and Waste Treatment Technology. The major specific concerns and requirements addressed are assurance that (1) radioactivity will be contained during waste transport, interim storage or while the waste is considered as retrievable from a repository facility, (2) the interim storage facilities will adequately isolate the radioactive material from the biosphere, (3) the terminal isolation facility will isolate the wastes from the biosphere over a time period allowing the radioactivity to decay to innocuous levels, (4) the terminal isolation mode for the waste will abbreviate the need for surveillance and institutional control by future generations, and (5) the public will accept the basic waste management strategy and geographical sites when needed

Comparative environmental evaluation of construction waste management through different waste sorting systems in Hong Kong.

Science.gov (United States)

Hossain, Md Uzzal; Wu, Zezhou; Poon, Chi Sun

2017-11-01

This study aimed to compare the environmental performance of building construction waste management (CWM) systems in Hong Kong. Life cycle assessment (LCA) approach was applied to evaluate the performance of CWM systems holistically based on primary data collected from two real building construction sites and secondary data obtained from the literature. Different waste recovery rates were applied based on compositions and material flow to assess the influence on the environmental performance of CWM systems. The system boundary includes all stages of the life cycle of building construction waste (including transportation, sorting, public fill or landfill disposal, recovery and reuse, and transformation and valorization into secondary products). A substitutional LCA approach was applied for capturing the environmental gains due to the utilizations of recovered materials. The results showed that the CWM system by using off-site sorting and direct landfilling resulted in significant environmental impacts. However, a considerable net environmental benefit was observed through an on-site sorting system. For example, about 18-30kg CO 2 eq. greenhouse gases (GHGs) emission were induced for managing 1 t of construction waste through off-site sorting and direct landfilling, whereas significant GHGs emission could be potentially avoided (considered as a credit -126 to -182kg CO 2 eq.) for an on-site sorting system due to the higher recycling potential. Although the environmental benefits mainly depend on the waste compositions and their sortability, the analysis conducted in this study can serve as guidelines to design an effective and resource-efficient building CWM system. Copyright © 2017 Elsevier Ltd. All rights reserved.

Human health and ecological risks from environmental restoration and waste management activities

International Nuclear Information System (INIS)

Pehlman, P.A.; Wollert, D.A.; Phillippi, R.H.

1994-01-01

This paper summarizes the methodologies for estimating human health and ecological risks resulting from Environmental Restoration and Waste Management activities across the Department of Energy (DOE) complex. DOE is currently assessing these activities as part of the Environmental Restoration and Waste Management Programmatic Environmental Impact Statement (EM-PEIS)

Assessment of environmental policy implementation in solid waste management in Kathmandu, Nepal.

Science.gov (United States)

Dangi, Mohan B; Schoenberger, Erica; Boland, John J

2017-06-01

In Nepal, full-fledged environmental legislation was rare before the democratic constitution of 1990. The first law covering the environment and sustainability was the Environment Protection Act 1997. While the Solid Waste Act was introduced in 1987, the problem of solid waste management still surfaces in Kathmandu. In order to understand the bedrock of this unrelenting failure in solid waste management, the manuscript digs deeper into policy implementation by dissecting solid waste rules, environmental legislations, relevant local laws, and solid waste management practices in Kathmandu, Nepal. A very rich field study that included surveys, interviews, site visits, and literature review provided the basis for the article. The study shows that volumes of new Nepalese rules are crafted without effective enforcement of their predecessors and there is a frequent power struggle between local government bodies and central authority in implementing the codes and allocating resources in solid waste management. The study concludes that Kathmandu does not require any new instrument to address solid waste problems; instead, it needs creation of local resources, execution of local codes, and commitment from central government to allow free exercise of these policies.

Risk assessment for the off-site transportation of high-level waste for the U.S. Department of Energy waste management programmatic environmental impact statement

International Nuclear Information System (INIS)

Monette, F.A.; Biwer, B.M.; LePoire, D.J.; Chen, S.Y.

1996-12-01

This report describes the human health risk assessment conducted for the transportation of high-level waste (HLW) in support of the US Department of Energy Waste Management Programmatic Environmental Impact Statement (WM PEIS). The assessment considers risks to collective populations and individuals under both routine and accident transportation conditions for truck and rail shipment modes. The report discusses the scope of the HLW transportation assessment, describes the analytical methods used for the assessment, defines the alternatives considered in the WM PEIS, and details important assessment assumptions. Results are reported for five alternatives. In addition, to aid in the understanding and interpretation of the results, specific areas of uncertainty are described, with an emphasis on how the uncertainties may affect comparisons of the alternatives

Comparative environmental analysis of waste brominated plastic thermal treatments

International Nuclear Information System (INIS)

Bientinesi, M.; Petarca, L.

2009-01-01

The aim of this research activity is to investigate the environmental impact of different thermal treatments of waste electric and electronic equipment (WEEE), applying a life cycle assessment methodology. Two scenarios were assessed, which both allow the recovery of bromine: (A) the co-combustion of WEEE and green waste in a municipal solid waste combustion plant, and (B) the staged-gasification of WEEE and combustion of produced syngas in gas turbines. Mass and energy balances on the two scenarios were set and the analysis of the life cycle inventory and the life cycle impact assessment were conducted. Two impact assessment methods (Ecoindicator 99 and Impact 2002+) were slightly modified and then used with both scenarios. The results showed that scenario B (staged-gasification) had a potentially smaller environmental impact than scenario A (co-combustion). In particular, the thermal treatment of staged-gasification was more energy efficient than co-combustion, and therefore scenario B performed better than scenario A, mainly in the impact categories of 'fossil fuels' and 'climate change'. Moreover, the results showed that scenario B allows a higher recovery of bromine than scenario A; however, Br recovery leads to environmental benefits for both the scenarios. Finally the study demonstrates that WEEE thermal treatment for energy and matter recovery is an eco-efficient way to dispose of this kind of waste

Solid waste: terminological and long-term environmental risk assessment problems exemplified in a power plant fly ash study.

Science.gov (United States)

Twardowska, Irena; Szczepanska, Jadwiga

2002-02-21

Legal definitions exert a significant impact on the waste management strategy. Waste that is technically suitable for recovery does not automatically become a raw material if there is no market for it, or its use is not commercially effective and, hence, they should be disposed of. The majority of disposed wastes, including recyclable waste, are not environmentally safe. Waste as a freshly generated anthropogenic material is not geochemically stable. Przezchlebie fly ash surface pond (Upper Silesia, Poland) in the post-closure stage was subject to field validation of the results of laboratory leaching/extraction tests and long-term column experiments on fly ash (FA) leaching behaviour under controlled conditions for environmental risk assessment. The study showed: (i) the possibility of a discontinuous non-linear time delayed increase of pollution potential of disused 'non-hazardous' large-volume waste in the dumping sites to the hazardous level; (ii) inconsistency of the laboratory leaching tests and the actual leaching behaviour of trace metals, particularly when equilibria conditions are dictated by kinetically determined reactions where the test results reflected entirely wash-out (I) and dissolution (II) phases, but did not comprise delayed release (III) phase; and (iii) necessity of life-cycle screening/monitoring of 'non-hazardous' dumping sites for contaminant release as a function of the primary (pH-Eh, ionic strength, ionic composition of solute) and secondary controlling factors (L/S-liquid to solid ratio, water flow conditions) along the vertical profile of an anthropogenic or natural vadose zone. These data are to be used to develop long-term predictive hydrogeochemical models and their field validation, and for providing an early warning and remedial actions with respect to the particular site. The formation of pH (and Eh) as a function of time-dependent (kinetically defined) processes appeared to be a key issue for a correct prediction of the

Environmental impact associated with activated carbon preparation from olive-waste cake via life cycle assessment.

Science.gov (United States)

Hjaila, K; Baccar, R; Sarrà, M; Gasol, C M; Blánquez, P

2013-11-30

The life cycle assessment (LCA) environmental tool was implemented to quantify the potential environmental impacts associated with the activated carbon (AC) production process from olive-waste cakes in Tunisia. On the basis of laboratory investigations for AC preparation, a flowchart was developed and the environmental impacts were determined. The LCA functional unit chosen was the production of 1 kg of AC from by-product olive-waste cakes. The results showed that impregnation using H3PO4 presented the highest environmental impacts for the majority of the indicators tested: acidification potential (62%), eutrophication (96%), ozone depletion potential (44%), human toxicity (64%), fresh water aquatic ecotoxicity (90%) and terrestrial ecotoxicity (92%). One of the highest impacts was found to be the global warming potential (11.096 kg CO2 eq/kg AC), which was equally weighted between the steps involving impregnation, pyrolysis, and drying the washed AC. The cumulative energy demand of the AC production process from the by-product olive-waste cakes was 167.63 MJ contributed by impregnation, pyrolysis, and drying the washed AC steps. The use of phosphoric acid and electricity in the AC production were the main factors responsible for the majority of the impacts. If certain modifications are incorporated into the AC production, such as implementing synthesis gas recovery and reusing it as an energy source and recovery of phosphoric acid after AC washing, additional savings could be realized, and environmental impacts could be minimized. Copyright © 2013 Elsevier Ltd. All rights reserved.

Environmental impact assessment of the incineration of municipal solid waste with auxiliary coal in China.

Science.gov (United States)

Zhao, Yan; Xing, Wei; Lu, Wenjing; Zhang, Xu; Christensen, Thomas H

2012-10-01

The environmental impacts of waste incineration with auxiliary coal were investigated using the life-cycle-based software, EASEWASTE, based on the municipal solid waste (MSW) management system in Shuozhou City. In the current system, MSW is collected, transported, and incinerated with 250 kg of coal per ton of waste. Based on observed environmental impacts of incineration, fossil CO(2) and heavy metals were primary contributors to global warming and ecotoxicity in soil, respectively. Compared with incinerators using excess coal, incineration with adequate coal presents significant benefits in mitigating global warming, whereas incineration with a mass of coal can avoid more impacts to acidification, photochemical ozone and nutrient enrichment because of increased electricity substitution and reduced emission from coal power plants. The "Emission standard of air pollutants for thermal power plants (GB13223-2011)" implemented in 2012 introduced stricter policies on controlling SO(2) and NO(x) emissions from coal power plants. Thus, increased use of auxiliary coal during incineration yields fewer avoided impacts on acidification and nutrient enrichment. When two-thirds of ash is source-separated and landfilled, the incineration of rest-waste presents better results on global warming, acidification, nutrient enrichment, and even ecotoxicity in soil. This process is considered a promising solution for MSW management in Shuozhou City. Weighted normalized environmental impacts were assessed based on Chinese political reduction targets. Results indicate that heavy metal and acidic gas emissions should be given more attention in waste incineration. This study provides scientific support for the management of MSW systems dominated by incineration with auxiliary coal in China. Copyright © 2012 Elsevier Ltd. All rights reserved.

Mixed Waste Integrated Program: A technology assessment for mercury-containing mixed wastes

International Nuclear Information System (INIS)

Perona, J.J.; Brown, C.H.

1993-03-01

The treatment of mixed wastes must meet US Environmental Protection Agency (EPA) standards for chemically hazardous species and also must provide adequate control of the radioactive species. The US Department of Energy (DOE) Office of Technology Development established the Mixed Waste Integrated Program (MWIP) to develop mixed-waste treatment technology in support of the Mixed Low-Level Waste Program. Many DOE mixed-waste streams contain mercury. This report is an assessment of current state-of-the-art technologies for mercury separations from solids, liquids, and gases. A total of 19 technologies were assessed. This project is funded through the Chemical-Physical Technology Support Group of the MWIP

In itinere strategic environmental assessment of an integrated provincial waste system.

Science.gov (United States)

Federico, Giovanna; Rizzo, Gianfranco; Traverso, Marzia

2009-06-01

In the paper, the practical problem of analysing in an integrated way the performance of provincial waste systems is approached, in the framework of the Strategic Environmental Assessment (SEA). In particular, the in itinere phase of SEA is analysed herein. After separating out a proper group of ambits, to which the waste system is supposed to determine relevant impacts, pertinent sets of single indicators are proposed. Through the adoption of such indicators the time trend of the system is investigated, and the suitability of each indicator is critically revised. The structure of the evaluation scheme, which is essentially based on the use of ambit issues and analytical indicators, calls for the application of the method of the Dashboard of Sustainability for the integrated evaluation of the whole system. The suitability of this method is shown through the paper, together with the possibility of a comparative analysis of different scenarios of interventions. Of course, the reliability of the proposed method strongly relies on the availability of a detailed set of territorial data. The method appears to represent a useful tool for public administration in the process of optimizing the policy actions aimed at minimizing the increasing problem represented by waste production in urban areas.

Savannah River Site Waste Management Final Environmental Impact Statement Addendum

International Nuclear Information System (INIS)

1995-07-01

The purpose of this environmental impact statement is to help DOE decide how to manage over the next 30 years liquid high-level radioactive, low-level radioactive, mixed, hazardous, and transuranic wastes generated during 40 years of past operations and on-going activities (including management of wastes received from offsite) at Savannah River Site (SRS) in southwestern South Carolina. The wastes are currently stored at SRS. DOE seeks to dispose of the wastes in a cost-effective manner that protects human health and the environment. In this document, DOE assesses the cumulative environmental impacts of storing, treating, and disposing of the wastes, examines the impacts of alternatives, and identifies measures available to reduce adverse impacts. Evaluations of impacts on water quality, air quality, ecological systems, land use, geologic resources, cultural resources, socio-economic, and the health and safety of onsite workers and the public are included in the assessment

Savannah River Site waste management. Final environmental impact statement - addendum

International Nuclear Information System (INIS)

1995-07-01

The purpose of this environmental impact statement is to help DOE decide how to manage over the next 30 years liquid high-level radioactive, low-level radioactive, mixed, hazardous, and transuranic wastes generated during 40 years of past operations and on-going activities (including management of wastes received from offsite) at Savannah River Site (SRS) in southwestern South Carolina. The wastes are currently stored at SRS. DOE seeks to dispose of the wastes in a cost-effective manner that protects human health and the environment. In this document, DOE assesses the cumulative environmental impacts of storing, treating, and disposing of the wastes, examines the impacts of alternatives, and identifies measures available to reduce adverse impacts. Evaluations of impacts on water quality, air quality, ecological systems, land use, geologic resources, cultural resources, socio-economics, and the health and safety of onsite workers and the public are included in the assessment

Environmental and economic analyses of waste disposal options for traditional markets in Indonesia

International Nuclear Information System (INIS)

Aye, Lu; Widjaya, E.R.

2006-01-01

Waste from traditional markets in Indonesia is the second largest stream of municipal solid waste after household waste. It has a higher organic fraction and may have greater potential to be managed on a business scale compared to household wastes. The attributed reason is that in general the wastes generated from traditional markets are more uniform, more concentrated and less hazardous than waste from other sources. This paper presents the results of environmental and economic assessments to compare the options available for traditional market waste disposal in Indonesia. The options compared were composting in labour intensive plants, composting in a centralised plant that utilised a simple wheel loader, centralised biogas production and landfill for electricity production. The current open dumping practice was included as the baseline case. A life cycle assessment (LCA) was used for environmental analysis. All options compared have lower environmental impacts than the current practice of open dumping. The biogas production option has the lowest environmental impacts. A cost-benefit analysis, which considered greenhouse gas savings, was used for the economic assessment. It was found that composting at a centralised plant is the most economically feasible option under the present Indonesian conditions. The approach reported in this study could be applied for 'a pre-feasibility first cut comparison' that includes environmental aspects in a decision-making framework for developing countries even though European emission factors were used

Application of Life Cycle Assessment on Electronic Waste Management: A Review

Science.gov (United States)

Xue, Mianqiang; Xu, Zhenming

2017-04-01

Electronic waste is a rich source of both valuable materials and toxic substances. Management of electronic waste is one of the biggest challenges of current worldwide concern. As an effective and prevailing environmental management tool, life cycle assessment can evaluate the environmental performance of electronic waste management activities. Quite a few scientific literatures reporting life cycle assessment of electronic waste management with significant outcomes have been recently published. This paper reviewed the trends, characteristics, research gaps, and challenges of these studies providing detailed information for practitioners involved in electronic waste management. The results showed that life cycle assessment studies were most carried out in Europe, followed by Asia and North America. The research subject of the studies mainly includes monitors, waste printed circuit boards, mobile phones, computers, printers, batteries, toys, dishwashers, and light-emitting diodes. CML was the most widely used life cycle impact assessment method in life cycle assessment studies on electronic waste management, followed by EI99. Furthermore, 40% of the reviewed studies combined with other environmental tools, including life cycle cost, material flow analysis, multi-criteria decision analysis, emergy analysis, and hazard assessment which came to more comprehensive conclusions from different aspects. The research gaps and challenges including uneven distribution of life cycle assessment studies, life cycle impact assessment methods selection, comparison of the results, and uncertainty of the life cycle assessment studies were examined. Although life cycle assessment of electronic waste management facing challenges, their results will play more and more important role in electronic waste management practices.

Technical Assessment Of Selection Of A Waste Disposal Site

International Nuclear Information System (INIS)

Lee, Bong Hun

1992-04-01

This book gives overall descriptions of technical assessment of selection of a waste disposal site, which deals with standard of selection on incinerator of city waste, the method over assessment of selection of incinerator in city waste, prerequisite of technical assessment for selection of incinerator, waste incinerator and related equipment such as form, structure, quality of material, ventilation device, plumbing system and electrical installation, and total plan like plan of construction and a measure taken against environmental pollution.

Environmental aspects of commercial radioactive waste management

International Nuclear Information System (INIS)

1979-05-01

Volume 2 contains chapters 6 through 10: environmental effects related to radioactive waste management associated with LWR fuel reprocessing - mixed-oxide fuel fabrication plant; environmental effects related to transporting radioactive wastes associated with LWR fuel reprocessing and fabrication; environmental effects related to radioactive waste management associated with LWR fuel reprocessing - retrievable waste storage facility; environmental effects related to geologic isolation of LWR fuel reprocessing wastes; and integrated systems for commercial radioactive waste management

Environmental assessment for the Radioactive and Mixed Waste Management Facility: Sandia National Laboratories/New Mexico

International Nuclear Information System (INIS)

1993-06-01

The Department of Energy (DOE) has prepared an environmental assessment (EA) (DOE/EA-0466) under the National Environmental Policy Act (NEPA) of 1969 for the proposed completion of construction and subsequent operation of a central Radioactive and Mixed Waste Management Facility (RMWMF), in the southeastern portion of Technical Area III at Sandia National Laboratory, Albuquerque (SNLA). The RMWMF is designed to receive, store, characterize, conduct limited bench-scale treatment of, repackage, and certify low-level waste (LLW) and mixed waste (MW) (as necessary) for shipment to an offsite disposal or treatment facility. The RMWMF was partially constructed in 1989. Due to changing regulatory requirements, planned facility upgrades would be undertaken as part of the proposed action. These upgrades would include paving of road surfaces and work areas, installation of pumping equipment and lines for surface impoundment, and design and construction of air locks and truck decontamination and water treatment systems. The proposed action also includes an adjacent corrosive and reactive metals storage area, and associated roads and paving. LLW and MW generated at SNLA would be transported from the technical areas to the RMWMF in containers approved by the Department of Transportation. The RMWMF would not handle nonradioactive hazardous waste. Based on the analysis in the EA, the proposed completion of construction and operation of the RMWMF does not constitute a major Federal action significantly affecting the quality of the human environment within the meaning of NEPA. Therefore, preparation of an environmental impact statement for the proposed action is not required

Melter development needs assessment for RWMC buried wastes

International Nuclear Information System (INIS)

Donaldson, A.D.; Carpenedo, R.J.; Anderson, G.L.

1992-02-01

This report presents a survey and initial assessment of the existing state-of-the-art melter technology necessary to thermally treat (stabilize) buried TRU waste, by producing a highly leach resistant glass/ceramic waste form suitable for final disposal. Buried mixed transuranic (TRU) waste at the Idaho National Engineering Laboratory (INEL) represents an environmental hazard requiring remediation. The Environmental Protection Agency (EPA) placed the INEL on the National Priorities List in 1989. Remediation of the buried TRU-contaminated waste via the CERCLA decision process is required to remove INEL from the National Priorities List. A Waste Technology Development (WTD) Preliminary Systems Design and Thermal Technologies Screening Study identified joule-heated and plasma-heated melters as the most probable thermal systems technologies capable of melting the INEL soil and waste to produce the desired final waste form [Iron-Enriched Basalt (IEB) glass/ceramic]. The work reported herein then surveys the state of existing melter technology and assesses it within the context of processing INEL buried TRU wastes and contaminated soils. Necessary technology development work is recommended

Identifying potential environmental impacts of waste handling strategies in textile industry.

Science.gov (United States)

Yacout, Dalia M M; Hassouna, M S

2016-08-01

Waste management is a successful instrument to minimize generated waste and improve environmental conditions. In spite of the large share of developing countries in the textile industry, limited information is available concerning the waste management strategies implemented for textiles on those countries and their environmental impacts. In the current study, two waste management approaches for hazardous solid waste treatment of acrylic fibers (landfill and incineration) were investigated. The main research questions were: What are the different impacts of each waste management strategy? Which waste management strategy is more ecofriendly? Life cycle assessment was employed in order to model the environmental impacts of each waste streaming approach separately then compare them together. Results revealed that incineration was the more ecofriendly approach. Highest impacts of both approaches were on ecotoxicity and carcinogenic potentials due to release of metals from pigment wastes. Landfill had an impact of 46.8 % on human health as compared to 28 % by incineration. Incineration impact on ecosystem quality was higher than landfill impact (68.4 and 51.3 %, respectively). As for resources category, incineration had a higher impact than landfill (3.5 and 2.0 %, respectively). Those impacts could be mitigated if state-of-the-art landfill or incinerator were used and could be reduced by applying waste to energy approaches for both management systems In conclusion, shifting waste treatment from landfill to incineration would decrease the overall environmental impacts and allow energy recovery. The potential of waste to energy approach by incineration with heat recovery could be considered in further studies. Future research is needed in order to assess the implementation of waste management systems and the preferable waste management strategies in the textile industry on developing countries.

Environmental performance of household waste management in Europe - An example of 7 countries.

Science.gov (United States)

Andreasi Bassi, Susanna; Christensen, Thomas H; Damgaard, Anders

2017-11-01

An attributional life cycle assessment (LCA) of the management of 1ton of household waste was conducted in accordance with ISO 14044:2006 and the ILCD Handbook for seven European countries, namely Germany, Denmark, France, UK, Italy, Poland and Greece, representing different household waste compositions, waste management practices, technologies, and energy systems. National data were collected from a range of sources regarding household waste composition, household sorting efficiency, collection, waste treatments, recycling, electricity and heat composition, and technological efficiencies. The objective was to quantify the environmental performance in the different countries, in order to analyze the sources of the main environmental impacts and national differences which affect the results. In most of the seven countries, household waste management provides environmental benefits when considering the benefits of recycling of materials and recovering and utilization of energy. Environmental benefits come from paper recycling and, to a lesser extent, the recycling of metals and glass. Waste-to-energy plants can lead to an environmental load (as in France) or a saving (Germany and Denmark), depending mainly on the composition of the energy being substituted. Sensitivity analysis and a data quality assessment identified a range of critical parameters, suggesting from where better data should be obtained. The study concluded that household waste management is environmentally the best in European countries with a minimum reliance on landfilling, also induced by the implementation of the Waste Hierarchy, though environmental performance does not correlate clearly with the rate of material recycling. From an environmental point of view, this calls for a change in the waste management paradigm, with less focus on where the waste is routed and more of a focus on the quality and utilization of recovered materials and energy. Copyright © 2017 Elsevier Ltd. All rights reserved.

Acute and chronic environmental effects of clandestine methamphetamine waste.

Science.gov (United States)

Kates, Lisa N; Knapp, Charles W; Keenan, Helen E

2014-09-15

The illicit manufacture of methamphetamine (MAP) produces substantial amounts of hazardous waste that is dumped illegally. This study presents the first environmental evaluation of waste produced from illicit MAP manufacture. Chemical oxygen demand (COD) was measured to assess immediate oxygen depletion effects. A mixture of five waste components (10mg/L/chemical) was found to have a COD (130 mg/L) higher than the European Union wastewater discharge regulations (125 mg/L). Two environmental partition coefficients, K(OW) and K(OC), were measured for several chemicals identified in MAP waste. Experimental values were input into a computer fugacity model (EPI Suite™) to estimate environmental fate. Experimental log K(OW) values ranged from -0.98 to 4.91, which were in accordance with computer estimated values. Experimental K(OC) values ranged from 11 to 72, which were much lower than the default computer values. The experimental fugacity model for discharge to water estimates that waste components will remain in the water compartment for 15 to 37 days. Using a combination of laboratory experimentation and computer modelling, the environmental fate of MAP waste products was estimated. While fugacity models using experimental and computational values were very similar, default computer models should not take the place of laboratory experimentation. Copyright © 2014 Elsevier B.V. All rights reserved.

U.S. Department of energy worker health risk evaluation methodology for assessing risks associated with environmental restoration and waste management

International Nuclear Information System (INIS)

Blaylock, B.P.; Legg, J.; Travis, C.C.; Scofield, P.A.

1995-06-01

This document describes a worker health risk evaluation methodology for assessing risks associated with Environmental Restoration (ER) and Waste Management (WM). The methodology is appropriate for estimating worker risks across the Department of Energy (DOE) Complex at both programmatic and site-specific levels. This document supports the worker health risk methodology used to perform the human health risk assessment portion of the DOE Programmatic Environmental Impact Statement (PEIS) although it has applications beyond the PEIS, such as installation-wide worker risk assessments, screening-level assessments, and site-specific assessments

U.S. Department of Energy worker health risk evaluation methodology for assessing risks associated with environmental restoration and waste management

Energy Technology Data Exchange (ETDEWEB)

Blaylock, B.P.; Legg, J.; Travis, C.C. [Oak Ridge National Lab., TN (United States). Center for Risk Management; Simek, M.A.; Sutherland, J. [Univ. of Tennessee, Knoxville, TN (United States); Scofield, P.A. [Office of Environmental Compliance and Documentation (United States)

1995-06-01

This document describes a worker health risk evaluation methodology for assessing risks associated with Environmental Restoration (ER) and Waste Management (WM). The methodology is appropriate for estimating worker risks across the Department of Energy (DOE) Complex at both programmatic and site-specific levels. This document supports the worker health risk methodology used to perform the human health risk assessment portion of the DOE Programmatic Environmental Impact Statement (PEIS) although it has applications beyond the PEIS, such as installation-wide worker risk assessments, screening-level assessments, and site-specific assessments.

Integrated environmental and economic assessment of waste management systems

DEFF Research Database (Denmark)

Martinez Sanchez, Veronica

in the “Optimization approach” the scenarios are the results of an optimization process. • The cost approach describes cost principles and level of LCA integration. Conventional and Environmental LCCs are financial assessments, i.e. include marketed goods/services, but while Environmental LCCs include environmental...... assessment of SWM systems alongside environmental impacts assessment to take budget constrains into account. In light of the need for combined environmental and economic assessment of SWM, this PhD thesis developed a consistent and comprehensive method for integrated environmental and economic assessment...... of SWM technologies and systems. The method resulted from developing further the generic Life Cycle Costing (LCC) framework suggested by Hunkeler et al. (2008) and Swarr et al. (2011) to apply it on the field of SWM. The method developed includes: two modelling approaches (Accounting and Optimization...

Technique for Reduction of Environmental Pollution from Construction Wastes

Science.gov (United States)

Bakaeva, N. V.; Klimenko, M. Y.

2017-11-01

The results of the research on the negative impact construction wastes have on the urban environment and construction ecological safety are described. The research results are based on the statistical data and indicators calculated with the use of environmental pollution assessment in the restoration system of urban buildings technical conditions. The technique for the reduction of environmental pollution from construction wastes is scientifically based on the analytic summary of scientific and practical results for ecological safety ensuring at major overhaul and current repairs (reconstruction) of the buildings and structures. It is also based on the practical application of the probability theory method, system analysis and disperse system theory. It is necessary to execute some stages implementing the developed technique to reduce environmental pollution from construction wastes. The stages include various steps starting from information collection to the system formation with optimum performance characteristics which are more resource saving and energy efficient for the accumulation of construction wastes from urban construction units. The following tasks are solved under certain studies: basic data collection about construction wastes accumulation; definition and comparison of technological combinations at each system functional stage intended for the reduction of construction wastes discharge into the environment; assessment criteria calculation of resource saving and energy efficiency; optimum working parameters of each implementation stage are created. The urban construction technique implementation shows that the resource saving criteria are from 55.22% to 88.84%; potential of construction wastes recycling is 450 million tons of construction damaged elements (parts).

Assessment of transportation risk for the U.S. Department of Energy Environmental Management programmatic environmental impact statement

International Nuclear Information System (INIS)

Chen, S.Y.; Monette, F.A.; Biwer, B.M.; Lazaro, M.A.; Hartmann, H.M.; Policastro, A.J.

1995-01-01

In its Programmatic Environmental Impact Statement (PEIS), the Office of Environmental Management (EM) of the U.S. Department of Energy (DOE) is considering a broad range of alternatives for the future management of radioactive and hazardous waste at the facilities of the DOE complex. The alternatives involve facilities to be used for treatment, storage, and disposal of various wastes generated from DOE environmental restoration activities and waste management operations. The evaluation includes five types of waste (four types of radioactive waste plus hazardous waste), 49 sites, and numerous cases associated with each alternative for waste management. In general, the alternatives are evaluated independently for each type of waste and reflect decentralized, regionalized, and centralized approaches. Transportation of waste materials is an integral component of the EM PEIS alternatives for waste management. The estimated impact on human health that is associated with various waste transportation activities is an important component of a complete appraisal of the alternatives. The transportation risk assessment performed for the EM PEIS is designed to ensure through uniform and judicious selection of models, data, and assumptions that relative comparisons of risk among the various alternatives are meaningful and consistent. Among other tasks, Argonne National Laboratory is providing technical assistance to the EM PEIS on transportation risk assessment. The objective is to perform a human health risk assessment for each type of waste relative to the EM PEIS alternatives for waste management. The transportation risk assessed is part of the overall impacts being analyzed for the EM PEIS to determine the safest, most environmentally and economically sound manner in which to satisfy requirements for waste management in the coming decades

Strategic environmental assessment of the national programme for the safe management of spent fuel and radioactive waste

Energy Technology Data Exchange (ETDEWEB)

Steinhoff, Mathias; Kallenbach-Herbert, Beate; Claus, Manuel [Oeko-Institut e.V. Darmstadt (Germany); and others

2015-03-27

The report on the strategic environmental audit for the national waste disposal program covers the following issues: aim of the study, active factors, environmental objectives; description and evaluation of environmental impact including site selection criteria for final repositories of heat generating radioactive waste, intermediate storage of spent fuel elements and waste from reprocessing plants, disposal of wastes retrieved from Asse II; hypothetical zero variants.

Strategic environmental assessment of the national programme for the safe management of spent fuel and radioactive waste

International Nuclear Information System (INIS)

Steinhoff, Mathias; Kallenbach-Herbert, Beate; Claus, Manuel

2015-01-01

The report on the strategic environmental audit for the national waste disposal program covers the following issues: aim of the study, active factors, environmental objectives; description and evaluation of environmental impact including site selection criteria for final repositories of heat generating radioactive waste, intermediate storage of spent fuel elements and waste from reprocessing plants, disposal of wastes retrieved from Asse II; hypothetical zero variants.

Environmental and waste management issues, causes, characteristics, and cures

International Nuclear Information System (INIS)

Duffy, L.P.

1992-01-01

The department of Energy (DOE) views as one of its most challenging problems the minimization, management, and cleanup of waste materials generated from Departmental operations. The challenges for the DOE have striking similarities to the environmental restoration and waste management challenges associated with energy production and the mining and mineral processing industries. Their challenges relate to uranium mining and the resulting mill tailings; decontamination and decommissioning of facilities; processing of nuclear materials and production of weapons components. Add to this the challenge of environmental restoration solutions for waste disposal practices of the past. The fundamental goal of the DOE is to ensure that risks to human health and safety and to the environment posed by the department's past, present, and future operations are either eliminated to reduced to prescribed levels by the year 2019. To achieve this goal they must be able to assess environmental and health impacts resulting from the low concentrations of contaminants. This paper presents an overview of the causes, characteristics, and cures for these environmental restoration and waste management issues

Environmental assessment of the atlas bio-energy waste wood fluidized bed gasification power plant. Final report

Energy Technology Data Exchange (ETDEWEB)

Holzman, M.I.

1995-08-01

The Atlas Bio-Energy Corporation is proposing to develop and operate a 3 MW power plant in Brooklyn, New York that will produce electricity by gasification of waste wood and combustion of the produced low-Btu gas in a conventional package steam boiler coupled to a steam-electric generator. The objectives of this project were to assist Atlas in addressing the environmental permit requirements for the proposed power plant and to evaluate the environmental and economic impacts of the project compared to more conventional small power plants. The project`s goal was to help promote the commercialization of biomass gasification as an environmentally acceptable and economically attractive alternative to conventional wood combustion. The specific components of this research included: (1) Development of a permitting strategy plan; (2) Characterization of New York City waste wood; (3) Characterization of fluidized bed gasifier/boiler emissions; (4) Performance of an environmental impact analysis; (5) Preparation of an economic evaluation; and (6) Discussion of operational and maintenance concerns. The project is being performed in two phases. Phase I, which is the subject of this report, involves the environmental permitting and environmental/economic assessment of the project. Pending NYSERDA participation, Phase II will include development and implementation of a demonstration program to evaluate the environmental and economic impacts of the full-scale gasification project.

Hanford low-level tank waste interim performance assessment

International Nuclear Information System (INIS)

Mann, F.M.

1997-01-01

The Hanford Low-Level Tank Waste Interim Performance Assessment examines the long-term environmental and human health effects associated with the disposal of the low-level fraction of the Hanford single and double-shell tank waste in the Hanford Site 200 East Area. This report was prepared as a good management practice to provide needed information about the relationship between the disposal system design and performance early in the disposal system project cycle. The calculations in this performance assessment show that the disposal of the low-level fraction can meet environmental and health performance objectives

Strategic environmental assessment for UK LLW management - 16392

International Nuclear Information System (INIS)

Craze, Andrew; Clark, Matthew; Davis, Pete

2009-01-01

NDA is delivering a Strategic Environmental Assessment (SEA) to underpin the UK Nuclear Industry Low Level Waste Strategy. The purpose of this assessment is embed sustainability issues into our decision making and to fulfill our requirements under the European Union's Strategic Environmental Assessment (SEA) Directive (2004/42/EU) and transposing UK Regulations, and to underpin the development of the strategy. The outputs of the SEA have provided input into particular aspects of the strategy, leading to a more robust and better informed result. Development of options to be assessed under the SEA has looked at a number of factors, including: - what the strategy is aiming to achieve - expectation from stakeholders as to what should be addressed - consideration of tactical approaches to implementation of the strategy in addition to high level strategic issues - links to other projects and programmes (for example the Environmental Safety Case for the Low Level Waste Repository. The SEA aims to provide a robust assessment of the environmental and sustainability impacts of alternative strategies for providing continued capability and capacity for the management and disposal of LLW in the UK. The assessment also considers other, more tactical, issues around implementation of the strategy, for example: issues around the location of LLW management facilities; the environmental impacts of alternative waste treatment options (metal recycling etc); considerations of alternative approaches to the classification of radioactive waste and opportunities that would result. Critical to the development of the SEA has been the involvement of statutory and non-statutory stakeholders, who have informed both the output and the approach taken. (authors)

Home composting as an alternative treatment option for organic household waste in Denmark: An environmental assessment using life cycle assessment-modelling

International Nuclear Information System (INIS)

Andersen, J.K.; Boldrin, A.; Christensen, T.H.; Scheutz, C.

2012-01-01

An environmental assessment of the management of organic household waste (OHW) was performed from a life cycle perspective by means of the waste-life cycle assessment (LCA) model EASEWASTE. The focus was on home composting of OHW in Denmark and six different home composting units (with different input and different mixing frequencies) were modelled. In addition, incineration and landfilling was modelled as alternatives to home composting. The most important processes contributing to the environmental impact of home composting were identified as greenhouse gas (GHG) emissions (load) and the avoided emissions in relation to the substitution of fertiliser and peat when compost was used in hobby gardening (saving). The replacement of fertiliser and peat was also identified as one of the most sensible parameters, which could potentially have a significant environmental benefit. Many of the impact categories (especially human toxicity via water (HTw) and soil (HTs)) were affected by the heavy metal contents of the incoming OHW. The concentrations of heavy metals in the compost were below the threshold values for compost used on land and were thus not considered to constitute a problem. The GHG emissions were, on the other hand, dependent on the management of the composting units. The frequently mixed composting units had the highest GHG emissions. The environmental profiles of the home composting scenarios were in the order of −2 to 16 milli person equivalents (mPE) Mg −1 wet waste (ww) for the non-toxic categories and −0.9 to 28 mPE Mg −1 ww for the toxic categories. Home composting performed better than or as good as incineration and landfilling in several of the potential impact categories. One exception was the global warming (GW) category, in which incineration performed better due to the substitution of heat and electricity based on fossil fuels.

Environmental evaluation of waste management scenarios - significance of the boundaries

NARCIS (Netherlands)

Ghinea, C.; Petraru, M.; Bressers, Johannes T.A.; Gavrilescu, M.

2012-01-01

Life cycle concept was applied to analyse and assess some municipal solid waste (MSW) management scenarios in terms of environmental impacts, particularised for Iasi city, Romania, where approximately 380 kg/cap/yr of waste are generated. Currently, the management processes include temporary

Environmental impact of incineration of calorific industrial waste: rotary kiln vs. cement kiln.

Science.gov (United States)

Vermeulen, Isabel; Van Caneghem, Jo; Block, Chantal; Dewulf, Wim; Vandecasteele, Carlo

2012-10-01

Rotary kiln incinerators and cement kilns are two energy intensive processes, requiring high temperatures that can be obtained by the combustion of fossil fuel. In both processes, fossil fuel is often substituted by high or medium calorific waste to avoid resource depletion and to save costs. Two types of industrial calorific waste streams are considered: automotive shredder residue (ASR) and meat and bone meal (MBM). These waste streams are of current high interest: ASR must be diverted from landfill, while MBM can no longer be used for cattle feeding. The environmental impact of the incineration of these waste streams is assessed and compared for both a rotary kiln and a cement kiln. For this purpose, data from an extensive emission inventory is applied for assessing the environmental impact using two different modeling approaches: one focusing on the impact of the relevant flows to and from the process and its subsystems, the other describing the change of environmental impact in response to these physical flows. Both ways of assessing emphasize different aspects of the considered processes. Attention is paid to assumptions in the methodology that can influence the outcome and conclusions of the assessment. It is concluded that for the incineration of calorific wastes, rotary kilns are generally preferred. Nevertheless, cement kilns show opportunities in improving their environmental impact when substituting their currently used fuels by more clean calorific waste streams, if this improvement is not at the expense of the actual environmental impact. Copyright © 2012 Elsevier Ltd. All rights reserved.

Environmental Restoration and Waste Management manpower needs assessment: US Department of Energy complex

Energy Technology Data Exchange (ETDEWEB)

Holmes, C.W.; Lewis, R.E.; Hunt, S.T. (Pacific Northwest Lab., Richland, WA (United States)); Finn, M.G. (Oak Ridge Associated Universities, Inc., TN (United States))

1992-06-01

A study was conducted Pacific Northwest Laboratory and Oak Ridge Associated Universities, Inc. to assess the supply and demand for 53 scientific, engineering, and technical occupations relevant to the US Department of Energy's (DOE's) Office of Environmental Restoration and Waste management (EM). These assessments were made by examining budget projections and the input of program/project and human resources managers throughout the DOE complex. Quantitative projections of full-time equivalent employees slots for each occupation have been developed for the 1993--1997 time frame. Qualitative assessments of the factors that affect recruitment, staffing, and retention are also reported. The implications of the study are discussed within the likely skills mix of the future workforce and the education and organization interventions most likely to address the needs of the DOE complex.

Environmental pollution from solid wastes

International Nuclear Information System (INIS)

Jervis, R.E.; Krishnan, S.S.; Accetone, P.; Arifin, N.; Ko, M.M.C.; Nhan, C.; Nguyen, L.; Vela, L.; Yee, T.

1992-01-01

Research completed under the CRP during the past two years has encompassed several related aspects of environmental problems associated with solid wastes: assessment of major sources of toxic elements in a variety of solid waste forms, their leachability by simulated groundwater or rain/acid rain and the determination of the contribution of hospital incinerator to atmospheric releases. The summary of the findings of these investigations are given in this report. Unexpected high levels of cadmium have been found in many solid wastes. Leaching tests indicate that, in some cases, over 70% of this can be leached out into the nearby waterways. Combustibility tests indicated that 35 to 45% of it is emitted to the atmosphere during burning. This explains the increased levels of cadmium in air particulates sampled downwind from waste incinerators. Plastic items in municipal and hospital wastes were particularly elevated in Cd, Cl, Cr, Ba and Zn. Up to 1300 μg/g of Cd was found in some domestic items. By inference, Pb also is found in some common plastics but the current studies did not permit Pb determination in solid wastes, but only in aerosols. (author). 8 tabs

Educational initiatives in environmental restoration and waste management

International Nuclear Information System (INIS)

Prestwich, S.M.

1990-01-01

Policy-makers responding to the urgency of the demands for a clean environment are finding that America lacks the technical know-how and the pool of technicians, scientists, and engineers to meet the environmental challenges. In response to the need for a technically skilled work force, government agencies and the private sector have worked to assess the probable effect of shortages and have sought ways to prevent the problem. The US Department of Energy (DOE) and its predecessor agencies have historically supported strong linkages between the academic community - the providers of scientists and engineers - and the department - the users of those workers - to assure an adequate supply of appropriately educated technicians, scientists, and engineers to conduct basic and applied research in support of the DOE's mission and to implement that mission. One of the department's challenges is the minimization, management, and cleanup of waste materials generated from departmental operations. The recently published Environmental Restoration and Waste Management Five-Year Plan for fiscal years 1992 through 1996 reaffirms DOE's policy of compliance with environmental laws and regulations. It also maps out the newly created Office of Environmental Restoration and Waste Management's aggressive programs to improve training and education, to arouse interest in pursuit of science/engineering careers, and to place special emphasis on recruiting minorities and women to technical fields vital to the environmental restoration/waste management mission

Life cycle assessment of a packaging waste recycling system in Portugal

International Nuclear Information System (INIS)

Ferreira, S.; Cabral, M.; Cruz, N.F. da; Simões, P.; Marques, R.C.

2014-01-01

Highlights: • We modeled a real packaging waste recycling system. • The analysis was performed using the life cycle assessment methodology. • The 2010 situation was compared with scenarios where the materials were not recycled. • The “Baseline” scenario seems to be more beneficial to the environment. - Abstract: Life Cycle Assessment (LCA) has been used to assess the environmental impacts associated with an activity or product life cycle. It has also been applied to assess the environmental performance related to waste management activities. This study analyses the packaging waste management system of a local public authority in Portugal. The operations of selective and refuse collection, sorting, recycling, landfilling and incineration of packaging waste were considered. The packaging waste management system in operation in 2010, which we called “Baseline” scenario, was compared with two hypothetical scenarios where all the packaging waste that was selectively collected in 2010 would undergo the refuse collection system and would be sent directly to incineration (called “Incineration” scenario) or to landfill (“Landfill” scenario). Overall, the results show that the “Baseline” scenario is more environmentally sound than the hypothetical scenarios

Life cycle assessment of a packaging waste recycling system in Portugal

Energy Technology Data Exchange (ETDEWEB)

Ferreira, S.; Cabral, M. [CEG-IST, ULisboa, Av. Rovisco Pais, 1049-001 Lisbon (Portugal); Cruz, N.F. da, E-mail: nunocruz@tecnico.ulisboa.pt [IST, ULisboa, Av. Rovisco Pais, 1049-001 Lisbon (Portugal); Simões, P. [IST, ULisboa, Av. Rovisco Pais, 1049-001 Lisbon (Portugal); Marques, R.C. [CESUR, IST, ULisboa, Av. Rovisco Pais, 1049-001 Lisbon (Portugal)

2014-09-15

Highlights: • We modeled a real packaging waste recycling system. • The analysis was performed using the life cycle assessment methodology. • The 2010 situation was compared with scenarios where the materials were not recycled. • The “Baseline” scenario seems to be more beneficial to the environment. - Abstract: Life Cycle Assessment (LCA) has been used to assess the environmental impacts associated with an activity or product life cycle. It has also been applied to assess the environmental performance related to waste management activities. This study analyses the packaging waste management system of a local public authority in Portugal. The operations of selective and refuse collection, sorting, recycling, landfilling and incineration of packaging waste were considered. The packaging waste management system in operation in 2010, which we called “Baseline” scenario, was compared with two hypothetical scenarios where all the packaging waste that was selectively collected in 2010 would undergo the refuse collection system and would be sent directly to incineration (called “Incineration” scenario) or to landfill (“Landfill” scenario). Overall, the results show that the “Baseline” scenario is more environmentally sound than the hypothetical scenarios.

Environmental assessment for OPG's deep geologic repository for low and intermediate level waste

International Nuclear Information System (INIS)

Barker, D.; Rawlings, M.; Beal, A.

2011-01-01

The environmental assessment process for the Deep Geologic Repository (DGR) Project was initiated very early in the planning stages. Feasibility studies were initiated in 2003, after Ontario Power Generation (OPG) and the Municipality of Kincardine signed a Memorandum of Understanding agreeing to assess options for long-term management of low and intermediate level waste (L and ILW) options at the Bruce nuclear site. The location of the DGR, in the Municipality of Kincardine, is based on a willing and informed host community. The preferred approach, the DGR at the Bruce nuclear site, was advanced based on results of feasibility studies which looked at a number of options for long-term management of L&ILW and support from the local community and their elected representatives. The federal environmental assessment of the project was initiated following the signing of a Host Community Agreement and completion of a telephone poll, the results of which indicated that the majority of Municipality of Kincardine residents support the project. The environmental assessment began in 2006 as a comprehensive study and was ultimately referred to a joint review panel process in 2009. The environmental assessment considers the potential near-term effects of the construction and operations of the proposed project. Because of the nature of the project, the assessment of effects also considers long-term effects extending out to the million year time-frame, including effects of climate change, glaciations and seismic activity. (author)

'Siteval' software for the environmental feasibility assessment of disposal and recycling of wastes

International Nuclear Information System (INIS)

Cautilli, F.; Musmeci, F.; Tassoni, E.

1998-01-01

The package 'Siteval', developed by ENEA, is a computerize method to approach, in an angle and flexible manner the comparative analysis for environmental compatibility of alternative sites for waste treatment plants. The software is the logical conclusion of both the environmental and territorial studies carried out by ENEA on siting waste treatment plants and landfills and the comparative analysis of environmental compatibility of candidate landfills. Siteval uses a data base in which are entered all the information useful to characterize the sites (constraints, geology, hydrogeology. etc.) and the design data of the plants. In output Siteval ranks the sites for their environmental compatibility. The package also allows a sensitivity analysis to spot the most relevant parameters on the compatibility rank [it

Environmental-benefit analysis of two urban waste collection systems

International Nuclear Information System (INIS)

Aranda Usón, Alfonso; Ferreira, Germán; Zambrana Vásquez, David; Zabalza Bribián, Ignacio; Llera Sastresa, Eva

2013-01-01

Sustainable transportation infrastructure and travel policies aim to optimise the use of transportation systems to achieve economic and related social and environmental goals. To this end, a novel methodology based on life cycle assessment (LCA) has been developed in this study, with the aim of quantifying, in terms of CO 2 emissions equivalent, the impact associated with different alternatives of waste collection systems in different urban typologies. This new approach is focussed on saving energy and raw materials and reducing the environmental impact associated with the waste collection system in urban areas, as well as allowing the design and planning of the best available technologies and most environment-friendly management. The methodology considers a large variety of variables from the point of view of sustainable urban transport such as the location and size of the urban area, the amount of solid waste generated, the level of social awareness on waste separation procedures, the distance between houses and waste collection points and the distance from the latter to the possible recovery plants and/or landfills, taking into account the material and energy recovery ratio within an integrated waste management system. As a case study, two different waste collection systems have been evaluated with this methodology in the ecocity Valdespartera located in Zaragoza, Spain, consisting of approximately 10,000 homes: (i) a system based on traditional truck transportation and manual collection, and (ii) a stationary vacuum waste collection system. Results show that, when operating at loads close to 100%, the stationary collection system has the best environmental performance in comparison with the conventional system. In contrast, when operating at load factors around 13% the environmental benefits in terms of net CO 2 -eq. emissions for the stationary collection system are around 60% lower in comparison with the conventional one. - Highlights: • A comprehensive

Environmental-benefit analysis of two urban waste collection systems

Energy Technology Data Exchange (ETDEWEB)

Aranda Usón, Alfonso, E-mail: alaranda@unizar.es; Ferreira, Germán; Zambrana Vásquez, David; Zabalza Bribián, Ignacio; Llera Sastresa, Eva

2013-10-01

Sustainable transportation infrastructure and travel policies aim to optimise the use of transportation systems to achieve economic and related social and environmental goals. To this end, a novel methodology based on life cycle assessment (LCA) has been developed in this study, with the aim of quantifying, in terms of CO{sub 2} emissions equivalent, the impact associated with different alternatives of waste collection systems in different urban typologies. This new approach is focussed on saving energy and raw materials and reducing the environmental impact associated with the waste collection system in urban areas, as well as allowing the design and planning of the best available technologies and most environment-friendly management. The methodology considers a large variety of variables from the point of view of sustainable urban transport such as the location and size of the urban area, the amount of solid waste generated, the level of social awareness on waste separation procedures, the distance between houses and waste collection points and the distance from the latter to the possible recovery plants and/or landfills, taking into account the material and energy recovery ratio within an integrated waste management system. As a case study, two different waste collection systems have been evaluated with this methodology in the ecocity Valdespartera located in Zaragoza, Spain, consisting of approximately 10,000 homes: (i) a system based on traditional truck transportation and manual collection, and (ii) a stationary vacuum waste collection system. Results show that, when operating at loads close to 100%, the stationary collection system has the best environmental performance in comparison with the conventional system. In contrast, when operating at load factors around 13% the environmental benefits in terms of net CO{sub 2}-eq. emissions for the stationary collection system are around 60% lower in comparison with the conventional one. - Highlights: • A

Environmental assessment of energy generation from agricultural and farm waste through anaerobic digestion.

Science.gov (United States)

Nayal, Figen Sisman; Mammadov, Aydin; Ciliz, Nilgun

2016-12-15

While Turkey is one of the world's largest producers and exporters of agricultural goods, it is also, at the same time a net importer of energy carriers. This dichotomy offers a strong incentive to generate energy from agricultural and farming waste; something which could provide energy security for rural areas. Combined with the enhanced energy security for farming areas, the production of energy in this manner could conceivably contribute to the overall national effort to reduce the Turkey's carbon footprint. This study explores the environmental benefits and burdens of one such option, that is, biogas production from a mixture of agricultural and animal waste through anaerobic digestion (AD), and its subsequent use for electricity and heat generation. A life-cycle assessment methodology was used, to measure the potential environmental impact of this option, in terms of global warming and total weighed impact, and to contrast it with the impact of producing the same amount of energy via an integrated gasification combined cycle process and a hard coal power plant. This study concentrates on an AD and cogeneration pilot plant, built in the Kocaeli province of Turkey and attempts to evaluate its potential environmental impacts. The study uses laboratory-scale studies, as well as literature and LCI databases to derive the operational parameters, yield and emissions of the plant. The potential impacts were calculated with EDIP 2003 methodology, using GaBi 5 LCA software. The results indicate that N 2 O emissions, resulting from the application of liquid and solid portions of digestate (a by-product of AD), as an organic fertilizer, are by far the largest contributors to global warming among all the life cycle stages. They constitute 68% of the total, whereas ammonia losses from the same process are the leading cause of terrestrial eutrophication. The photochemical ozone formation potential is significantly higher for the cogeneration phase, compared to other life

Nuclear fuel waste management and disposal concept: Report. Federal environmental assessment review process

International Nuclear Information System (INIS)

1998-01-01

The Canadian concept for disposing CANDU reactor waste or high-level nuclear wastes from reprocessing involves underground disposal in sealed containers emplaced in buffer-filled and sealed vaults 500--1,000 meters below ground, in plutonic rock of the Canadian Shield. This document presents the report of a panel whose mandate was to review this concept (rather than a specific disposal project at a specific site) along with a broad range of related policy issues, and to conduct that review in five provinces (including reviews with First Nations groups). It first outlines the review process and then describes the nature of the problem of nuclear waste management. It then presents an overview of the concept being reviewed, its implementation stages, performance assessment analyses performed on the concept, and implications of a facility based on that concept (health, environmental, social, transportation, economic). The fourth section examines the criteria by which the safety and acceptability of the concept should be evaluated. This is followed by a safety and acceptability evaluation from both technical and social perspectives. Section six proposes future steps for building and determining acceptability of the concept, including an Aboriginal participation process, creation of a Nuclear Fuel Waste Management Agency, and a public participation process. The final section discusses some issues outside the panel's mandate, such as energy policy and renewable energy sources. Appendices include a chronology of panel activities, a review of radiation hazards, comparison between nuclear waste management and the management of other wastes, a review of other countries' approaches to long-term management of nuclear fuel wastes, and details of a siting process proposed by the panel

Environmental impact assessment of the Swedish high-level radioactive waste disposal system - examples of likely considerations

International Nuclear Information System (INIS)

1994-01-01

Sweden is investigating the feasibility of establishing a high-level radioactive waste (HLW) disposal system consisting of three components as follows: (1) Encapsulation facility, (2) system for transporting waste and (3) geologic repository. Swedish law requires that an Environmental Impact Assessment (EIA) be written for any planned action expected to have a significant impact on the environment. Before embarking on construction and operation of a HLW disposal system, the Swedish government will evaluate the expected environmental impacts to assure that the Swedish people and environmental will not be unduly affected by the disposal system. The EIA process requires that reasonable alternatives to the proposed action, including the 'zero' or 'no action' alternative, be considered so that the final approved plan for disposal will have undergone scrutiny and comparison of alternatives to arrive at a plan which is the best achievable given reasonable physical and monetary constraints. This report has been prepared by the Center for Nuclear Waste Regulatory Analyses (CNWRA) for use by the Swedish Radiation Protection Institute (SSI). The purpose of this report is to establish a document which outlines the types of information which would be in an EIA for a three part disposal system like that envisioned by the Swedish Nuclear Fuel and Waste Management Company (SKB) for the disposal of Sweden's HLW. Technical information that would normally be included in an EIA is outlined in this document. The SSI's primary interest is in radiological impacts. However, for the sake of completeness and also to evaluate all environmental impacts in a single document, non-radiological impacts are also included. Swedish authorities other than the SSI may have interest in the non-radiological parts of the document. 26 refs

Management of commercial high-level and transuranium-contaminated radioactive wastes. Environmental statement

International Nuclear Information System (INIS)

1974-09-01

This Draft Environmental Statement is issued to assess the environmental impact of the AEC's program to manage commercial high-level and transuranium-contaminated radioactive wastes. These are the types of commercial radioactive wastes for which AEC custody is required by present or anticipated regulations. The program consists of three basic parts: development of a Retrievable Surface Storage Facility (RSSF) for commercial high-level waste, using existing technology; evaluating geological formations and sites for the development of a Geological Disposal Pilot Plant (GDPP) which would lead to permanent disposal; and providing retrievable storage for the transuranium-contaminated waste pending availability of permanent disposal. Consideration has been given to all environmental aspects of the program, using waste generation projections through the year 2000. Radiological and other impacts of implementing the program are expected to be minimal, but will be discussed in further environmental statements which will support budget actions for specific repositories. The alternatives discussed in this Draft Environmental Statement are presented. (U.S.)

Accelerator Production of Tritium project process waste assessment

Energy Technology Data Exchange (ETDEWEB)

Carson, S.D.; Peterson, P.K.

1995-09-01

DOE has made a commitment to compliance with all applicable environmental regulatory requirements. In this respect, it is important to consider and design all tritium supply alternatives so that they can comply with these requirements. The management of waste is an integral part of this activity and it is therefore necessary to estimate the quantities and specific wastes that will be generated by all tritium supply alternatives. A thorough assessment of waste streams includes waste characterization, quantification, and the identification of treatment and disposal options. The waste assessment for APT has been covered in two reports. The first report was a process waste assessment (PWA) that identified and quantified waste streams associated with both target designs and fulfilled the requirements of APT Work Breakdown Structure (WBS) Item 5.5.2.1. This second report is an expanded version of the first that includes all of the data of the first report, plus an assessment of treatment and disposal options for each waste stream identified in the initial report. The latter information was initially planned to be issued as a separate Waste Treatment and Disposal Options Assessment Report (WBS Item 5.5.2.2).

Accelerator Production of Tritium project process waste assessment

International Nuclear Information System (INIS)

Carson, S.D.; Peterson, P.K.

1995-09-01

DOE has made a commitment to compliance with all applicable environmental regulatory requirements. In this respect, it is important to consider and design all tritium supply alternatives so that they can comply with these requirements. The management of waste is an integral part of this activity and it is therefore necessary to estimate the quantities and specific wastes that will be generated by all tritium supply alternatives. A thorough assessment of waste streams includes waste characterization, quantification, and the identification of treatment and disposal options. The waste assessment for APT has been covered in two reports. The first report was a process waste assessment (PWA) that identified and quantified waste streams associated with both target designs and fulfilled the requirements of APT Work Breakdown Structure (WBS) Item 5.5.2.1. This second report is an expanded version of the first that includes all of the data of the first report, plus an assessment of treatment and disposal options for each waste stream identified in the initial report. The latter information was initially planned to be issued as a separate Waste Treatment and Disposal Options Assessment Report (WBS Item 5.5.2.2)

Proposed integrated hazardous waste disposal facility. Public environmental review

International Nuclear Information System (INIS)

1998-05-01

This Public Environmental Report describes a proposal by the Health Department of Western Australia to establish a disposal facility for certain hazardous wastes and seeks comments from governments agencies and the public that will assist the EPA to make its recommendations to. The facility would only be used for wastes generated in Western Australia.The proposal specifically includes: a high temperature incinerator for the disposal of organo-chlorines (including agricultural chemicals and PCBs), and other intractable wastes for which this is the optimum disposal method; an area for the burial (after any appropriate conditioning) of low level radioactive intractable wastes arising from the processing of mineral sands (including monazite, ilmenite and zircon) and phosphate rock. Detailed information is presented on those wastes which are currently identified as requiring disposal at the facility.The proposed facility will also be suitable for the disposal of other intractable wastes including radioactive wastes (from industry, medicine and research) and other solid intractable wastes of a chemical nature including spent catalysts etc. Proposals to dispose of these other wastes at this facility in the future will be referred to the Environmental Protection Authority for separate assessment

Objective function for the environmental assessment of waste

International Nuclear Information System (INIS)

Toy, A.J.; Boegel, J.; Cohen, J.J.

1976-01-01

Various waste management systems were examined in order to determine what the environmental impacts might be and to rank the relative importance of those impacts. This examination determined that radiation dose to man was the most significant, and probably overriding, impact. This report describes methods of providing an objective function for dose to man. The search for an objective function began with a reading of Federal Regulations and the output of various standard setting councils and committees. Ample guidance was found on maximum allowable doses to individuals but no guidance on dose to large populations or criteria by which systems could be compared or optimized. Several other ways were postulated by which waste management systems could be evaluated besides maximum allowable dose to individuals. 0.1 man-rem per MW(e)-year was selected as the measure of system performance. This unit compares a rational estimate of population dose commitment with the concurrent benefit

Characterization of the Defense Waste Processing Facility (DWPF) Environmental Assessment (EA) glass Standard Reference Material. Revision 1

Energy Technology Data Exchange (ETDEWEB)

Jantzen, C.M.; Bibler, N.E.; Beam, D.C.; Crawford, C.L.; Pickett, M.A.

1993-06-01

Liquid high-level nuclear waste at the Savannah River Site (SRS) will be immobilized by vitrification in borosilicate glass. The glass will be produced and poured into stainless steel canisters in the Defense Waste Processing Facility (DWPF). Other waste form producers, such as West Valley Nuclear Services (WVNS) and the Hanford Waste Vitrification Project (HWVP), will also immobilize high-level radioactive waste in borosilicate glass. The canistered waste will be stored temporarily at each facility for eventual permanent disposal in a geologic repository. The Department of Energy has defined a set of requirements for the canistered waste forms, the Waste Acceptance Product Specifications (WAPS). The current Waste Acceptance Primary Specification (WAPS) 1.3, the product consistency specification, requires the waste form producers to demonstrate control of the consistency of the final waste form using a crushed glass durability test, the Product Consistency Test (PCI). In order to be acceptable, a waste glass must be more durable during PCT analysis than the waste glass identified in the DWPF Environmental Assessment (EA). In order to supply all the waste form producers with the same standard benchmark glass, 1000 pounds of the EA glass was fabricated. The chemical analyses and characterization of the benchmark EA glass are reported. This material is now available to act as a durability and/or redox Standard Reference Material (SRM) for all waste form producers.

Supplemental information related to risk assessment for the off-site transportation of low-level mixed waste for the U.S. Department of Energy waste management programmatic environmental impact statement

International Nuclear Information System (INIS)

Monette, F.A.; Biwer, B.M.; LePoire, D.J.; Lazaro, M.A.; Antonopoulos, A.A.; Hartmann, H.M.; Policastro, A.J.; Chen, S.Y.

1996-12-01

This report provides supplemental information to support the human health risk assessment conducted for the transportation of low-level mixed waste (LLMW) in support of the US Department of Energy Waste Management Programmatic Environmental Impact Statement (WM PEIS). The assessment considers both the radioactive and chemical hazards associated with LLMW transportation. Detailed descriptions of the transportation health risk assessment methods and results of the assessment are presented in Appendix E of the WM PEIS. This report presents additional information that is not included in Appendix E but that was needed to conduct the transportation risk assessment for Waste Management (WM) LLMW. Included are definitions of the LLMW alternatives considered in the WM PEIS; data related to the inventory and to the physical, chemical, and radiological characteristics of WM LLMW; an overview of the risk assessment methods; and detailed results of the assessment for each WM LLMW case considered

Supplemental information related to risk assessment for the off-site transportation of low-level mixed waste for the U.S. Department of Energy Waste Management programmatic environmental impact statement

International Nuclear Information System (INIS)

Monette, F.A.; Biwer, B.M.; LePoire, D.J.

1995-04-01

This report provides supplemental information to support the human health risk assessment conducted for the transportation of low-level mixed waste (LLMW) in support of the US Department of Energy Waste Management Programmatic Environmental Impact Statement (WM PEIS). The assessment considers both the radioactive and chemical hazards associated with LLMW transportation. Detailed descriptions of the transportation health risk assessment methods and results of the assessment are presented in Appendix E of the WM PEIS. This report presents additional information that is not included in Appendix E but is necessary to conduct the transportation risk assessment for Waste Management (WM) LLMW. Included are definitions of the LLMW alternatives considered in the WM PEIS; data related to the inventory and to the physical, chemical, and radiological characteristics of WM LLMW; an overview of the risk assessment methods; and detailed results of the assessment for each WM LLMW case considered

Assessment of environmental impact models in natural occurring radionuclides solid wastes disposal from the mineral industry

International Nuclear Information System (INIS)

Pontedeiro, Elizabeth May Braga Dulley

2006-07-01

This work evaluates the behavior of wastes with naturally occurring radionuclides as generated by the mineral industry and their final disposal in landfills. An integrated methodology is used to predict the performance of an industrial landfill for disposal of wastes containing NORM/TENORM, and to define acceptable amounts that can be disposed at the landfill using long-term environmental assessment. The governing equations for radionuclide transport are solved analytically using the generalized integral transform technique. Results obtained for each compartment of the biogeosphere are validated with experimental results or compared to other classes of solutions. An impact analysis is performed in order to define the potential consequences of a landfill to the environment, considering not only the engineering characteristics of the waste deposit but also the exposure pathways and plausible scenarios in which the contaminants could migrate and reach the environment and the human population. The present work permits the development of a safety approach that can be used to derive quantitative waste acceptance criteria for the disposal of NORM/TENORM waste in landfills. (author)

Characterizing the environmental impact of metals in construction and demolition waste.

Science.gov (United States)

Yu, Danfeng; Duan, Huabo; Song, Qingbin; Li, Xiaoyue; Zhang, Hao; Zhang, Hui; Liu, Yicheng; Shen, Weijun; Wang, Jinben

2018-05-01

Large quantities of construction and demolition (C&D) waste are generated in China every year, but their potential environmental impacts on the surrounding areas are rarely assessed. This study focuses on metals contained in C&D waste, characterizing the metal concentrations and their related environmental risks. C&D waste samples were collected in Shenzhen City, China, from building demolition sites, renovation areas undergoing refurbishment, landfill sites, and recycling companies (all located in Shenzhen city) that produce recycled aggregate, in order to identify pollution levels of the metals As, Cd, Cr, Cu, Pb, Ni, and Zn. The results showed that (1) the metal concentrations in most demolition and renovation waste samples were below the soil environmental quality standard for agricultural purposes (SQ-Agr.) in China; (2) Cd, Cu, and Zn led to relatively higher environmental risks than other metals, especially for Zn (DM5 tile sample, 360 mg/kg; R4 tile sample, 281 mg/kg); (3) non-inert C&D waste such as wall insulation and foamed plastic had high concentrations of As and Cd, so that these materials required special attention for sound waste management; and (4) C&D waste collected from landfill sites had higher concentrations of Cd and Cu than did waste collected from demolition and refurbishment sites.

Environmental impacts of food waste: Learnings and challenges from a case study on UK

DEFF Research Database (Denmark)

Tonini, Davide; Albizzati, Paola Federica; Astrup, Thomas Fruergaard

2018-01-01

Food waste, particularly when avoidable, incurs loss of resources and considerable environmental impacts due to the multiple processes involved in the life cycle. This study applies a bottom-up life cycle assessment method to quantify the environmental impacts of the avoidable food waste generate...... highlight the challenges related to modelling and methodological choices. Particularly, food production datasets should be chosen and used carefully, to avoid double counting and overestimation of the final impacts.......Food waste, particularly when avoidable, incurs loss of resources and considerable environmental impacts due to the multiple processes involved in the life cycle. This study applies a bottom-up life cycle assessment method to quantify the environmental impacts of the avoidable food waste generated...... by four sectors of the food supply chain in United Kingdom, namely processing, wholesale and retail, food service, and households. The impacts were quantified for ten environmental impact categories, from Global Warming to Water Depletion, including indirect land use change impacts due to demand for land...

Environmental performance of household waste management in Europe - an example of 7 countries

DEFF Research Database (Denmark)

Andreasi Bassi, Susanna; Christensen, Thomas Højlund; Damgaard, Anders

2017-01-01

compositions, waste management practices, technologies, and energy systems. National data were collected from a range of sources regarding household waste composition, household sorting efficiency, collection, waste treatments, recycling, electricity and heat composition, and technological efficiencies......An attributional life cycle assessment (LCA) of the management of 1 ton of household waste was conducted in accordance with ISO 14044:2006 and the ILCD Handbook for seven European countries, namely Germany, Denmark, France, UK, Italy, Poland and Greece, representing different household waste....... The objective was to quantify the environmental performance in the different countries, in order to analyze the sources of the main environmental impacts and national differences which affect the results. In most of the seven countries, household waste management provides environmental benefits when considering...

Environmental impact assessment in the Nordic Countries

International Nuclear Information System (INIS)

Broden, K.; Palsson, S.E.; Poroddsson, P.

2000-12-01

A meeting on Environmental Impact Assessment has been held in Iceland, September 2-6, 2000. It was held within the framework of the project NKS/SOS-3 (Radioactive waste), subproject NKS/SOS-3.1 (Environmental Impact Assessment). The meeting included presentations, discussions and a study trip to the Egilsstadir and Myvatn districts. (au)

Life-cycle assessment of energy consumption and environmental impact of an integrated food waste-based biogas plant

International Nuclear Information System (INIS)

Jin, Yiying; Chen, Ting; Chen, Xin; Yu, Zhixin

2015-01-01

Highlights: • 47.76% of the energy consumption is from the primary treatment process. • The dominant environmental impact comes from GWP100 emission (96.97 kgCO 2 -eq/t). • Increasing recycling rate of product can effectively reduce consumption and impact. - Abstract: Recycling food waste to produce biogas by anaerobic digestion (AD) is a promising process that can both provide renewable energy and dispose solid waste safely. However, this process affects the environment due to greenhouse gas emissions. By lifecycle assessment (LCA), we assessed the energy consumption (EC) and environmental impact (EI) of an integrated food waste-based biogas system and its subsystems. Data were collected from an actual plant in China that adopted a combination of wet-heat treatment and wet AD process at thermophilic condition. The EC of the system for processing 1 ton of waste was 663.89 MJ, among which 47.76% was from the primary treatment process (including pretreatment and AD). The GWP 100 (100-year global warming potential) emission of the system reached 96.97 kgCO 2 -eq/t, and the AP (acidification potential), EP (eutrophication potential), HTP inf (human toxicity potential) and FAETP inf (fresh water ecotoxicity) emissions were low. The EI was mainly generated by two subsystems, namely, the primary treatment and the secondary pollution control. Sensitivity analysis showed that a 40% increase of the feed fat content resulted in 38% increase in the net energy value output and 48% decrease in EP effect. The increase in oil content and biogas production rate could significantly reduce the EC and EI of the system. It has been shown that improving the technology of the process and increasing the recycling rate of products will result in the reduction of EC and EI of the biogas system. In addition, a quantitative assessment model of EC and EI in integrated food waste-based biogas technology is established

Co-ordination of federal and provincial environmental assessment processes for the Point Lepreau Generating Station Solid Radioactive Waste Management Facility modifications

International Nuclear Information System (INIS)

Hickman, C.; Thompson, P.D.; Barnes, J.

2006-01-01

Modification of the Solid Radioactive Waste Management Facility at Point Lepreau Generating Station is required to accommodate waste generated during and after an 18-month maintenance outage during which the station would be Refurbished. The modification of the facility triggered both federal and provincial environmental assessment requirements, and these assessments were conducted in a 'coordinated' and cooperative fashion. In this project, the coordinated approach worked well, and provided some significant advantages to the proponent, the public and the regulators. However, there are opportunities for further improvement in future projects, and this paper explores the advantages and disadvantages of this 'co-ordinated' approach. As part of this exploration, there is a discussion of administrative and regulatory changes that the province is considering for the environmental assessment process, and a discussion of the need for a formal 'harmonization' agreement. (author)

Pollution prevention opportunity assessment: Foundation of pollution prevention for waste management

International Nuclear Information System (INIS)

Damewood, R.W.

1994-01-01

The objective of this paper is to promote the Pollution Prevention Opportunity Assessment (PPOA) technique as a fundamental of pollution prevention for waste management. All key elements of an effective PPOA program are presented. These key elements include impacts of environmental laws on pollution prevention, PPOA concepts and overview, waste minimization opportunities assessment, reporting and monitoring waste minimization progress, and PPOA program implementation. As environmental laws evolve the focus is shifting from end-of-pipe pollution control to front-end source reduction. Waste minimization was mistakenly interpreted to mean the reduction of hazardous waste after generation in the past. The Pollution Prevention Act of 1990 has clearly defined its requirement on resource reduction. Waste reduction can be viewed as a criterion to assess all industrial processes and operations. The fundamental approach of PPOA focuses on a mass balance concept. This concept deals with tracking of chemicals from the point of purchase, through storage, utilization in the process, and waste generation at the end of process. In other words, PPOA is a technique to analyze this input/output process. By applying PPOA techniques, the framework of applicable compliance requirements to the current operation process is established. Furthermore, documentation of PPOA itself can meet as documentation requirements for environmental compliance. In general, the PPOA process consists of two phases. The first phase involves input and output process description and waste characterization. The second phase is an opportunities assessment for waste minimization from input/output waste characterization. These two phases are explained in detail in the paper

Methodology for predictive modeling of environmental transport and health effects for waste sites at the Savannah River Plant: Environmental information document

International Nuclear Information System (INIS)

Stephensen, D.E.; King, C.M.; Looney, B.B.; Grant, M.W.

1987-03-01

This document provides information on the methods used to predict chemical transport and the associated health risk for various postulated closure activities at waste sites. The document was prepared as background documentation for the Department of Energy's proposed Environmental Impact Statement (EIS) on waste management activities for groundwater protection at the Savannah River Plant (SRP). The various mathematical formulations used in the environmental transport analysis, the exposure assessment, and the health risk assessment used in the analysis of all foreseeable scenarios as defined by the National Environmental Policy Act (CFR, 1986) are presented in this document. The scenarios do not necessarily represent actual environmental conditions for every SRP waste site. This document was prepared in support of the National Environmental Policy Act process, but does not by itself satisfy federal or state regulatory requirements. 29 refs., 11 figs

Site specific plan. [Environmental Restoration and Waste Management, Savannah River Site

Energy Technology Data Exchange (ETDEWEB)

Hutchison, J.; Jernigan, G.

1989-12-01

The Environmental Restoration and Waste Management Five-Year Plan (FYP) covers the period for FY 1989 through FY 1995. The plan establishes a Department of Energy -- Headquarters (DOE-HQ) agenda for cleanup and compliance against which overall progress can be measured. The FYP covers three areas: Corrective Activities, Environmental Restoration, and Waste Management Operations. Corrective Activities are those activities necessary to bring active or standby facilities into compliance with local, state, and federal environmental regulations. Environmental restoration activities include the assessment and cleanup of surplus facilities and inactive waste sites. Waste management operations includes the treatment, storage, and disposal of wastes which are generated as a result of ongoing operations. This Site Specific Plan (SSP) has been prepared by the Savannah River Site (SRS) in order to show how environmental restoration and waste management activities that were identified during the preparation of the FYP will be implemented, tracked, and reported. The SSP describes DOE Savannah River (DOE-SR) and operating contractor, Westinghouse Savannah River Company (WSRC), organizations that are responsible, for undertaking the activities identified in this plan. The SSP has been prepared in accordance with guidance received from DOE-HQ. DOE-SR is accountable to DOE-HQ for the implementation of this plan. 8 refs., 46 figs., 23 tabs.

Hanford site tank waste remediation system programmatic environmental review report

International Nuclear Information System (INIS)

Haass, C.C.

1998-01-01

The US Department of Energy (DOE) committed in the Tank Waste Remediation System (TWRS) Environmental Impact Statement (EIS) Record of Decision (ROD) to perform future National Environmental Policy Act (NEPA) analysis at key points in the Program. Each review will address the potential impacts that new information may have on the environmental impacts presented in the TWRS EIS and support an assessment of whether DOE's plans for remediating the tank waste are still pursuing the appropriate plan for remediation or whether adjustments to the program are needed. In response to this commitment, DOE prepared a Supplement Analysis (SA) to support the first of these reevaluations. Subsequent to the completion of the SA, the Phase IB negotiations process with private contractors resulted in several changes to the planned approach. These changes along with other new information regarding the TWRS Program have potential implications for Phase 1 and Phase 2 of tank waste retrieval and waste storage and/or disposal that may influence the environmental impacts of the Phased Implementation alternative. This report focuses on identifying those potential environmental impacts that may require NEPA analysis prior to authorization to begin facility construction and operations

Assessing the environmental performance of construction materials testing using EMS: An Australian study.

Science.gov (United States)

Dejkovski, Nick

2016-10-01

This paper reports the audit findings of the waste management practices at 30 construction materials testing (CMT) laboratories (constituting 4.6% of total accredited CMT laboratories at the time of the audit) that operate in four Australian jurisdictions and assesses the organisation's Environmental Management System (EMS) for indicators of progress towards sustainable development (SD). In Australia, waste indicators are 'priority indicators' of environmental performance yet the quality and availability of waste data is poor. National construction and demolition waste (CDW) data estimates are not fully disaggregated and the contribution of CMT waste (classified as CDW) to the national total CDW landfill burden is difficult to quantify. The environmental and human impacts of anthropogenic release of hazardous substances contained in CMT waste into the ecosphere can be measured by construing waste indicators from the EMS. An analytical framework for evaluating the EMS is developed to elucidate CMT waste indicators and assess these indicators against the principle of proportionality. Assessing against this principle allows for: objective evaluations of whether the environmental measures prescribed in the EMS are 'proportionate' to the 'desired' (subjective) level of protection chosen by decision-makers; and benchmarking CMT waste indicators against aspirational CDW targets set by each Australian jurisdiction included in the audit. Construed together, the EMS derived waste indicators and benchmark data provide a composite indicator of environmental performance and progress towards SD. The key audit findings indicate: CMT laboratories have a 'poor' environmental performance (and overall progress towards SD) when EMS waste data are converted into indicator scores and assessed against the principle of proportionality; CMT waste recycling targets are lower when benchmarked against jurisdictional CDW waste recovery targets; and no significant difference in the average

Environmental assessment of municipal solid waste management in Sri Lanka and India in a life cycle perspective

Energy Technology Data Exchange (ETDEWEB)

Menikpura, S.N.M.; Bonnet, Sebastien; Gheewala, Shabbir H. [King Mongkut' s Univ. of Technology Thonburi, Bangkok (Thailand). Joint Graduate School of Energy and Environment; Ministry of Education (Thailand). Center for Energy Technology and Environment

2010-07-01

At present, many Asian developing countries are practicing poor Municipal Solid Waste (MSW) management methods such as open dumping and non-engineered landfilling. This creates severe burdens on the environment and threat to human health. The quantification of the environmental impacts resulting from such poor MSW management practices is necessary to serve as a baseline against which alternative treatment technology options can be assessed for implementation of more environmentally sustainable MSW management systems that are adapted to local situation. In this study, existing MSW management systems in Ski Lanka and India were evaluated in order to assess the severity of their environmental impacts with focus on global warming potential and abiotic resource depletion. Life Cycle Assessment methodology was followed to perform this investigation. Results from this study reveal that the existing MSW management methods used in both countries cause severe environmental damages. However, the situation in India is slightly better as compared to Sri Lanka since 24% of its MSW is being composted. The implementation of landfill with landfill gas recovery for energy was identified as an important initial step to overcome the existing environmental impacts assessed. The results obtained revealed that implementation of such systems would help substantially to reduce global warming potential and abiotic resources depletion. (orig.)

Multi-criteria evaluation in strategic environmental assessment for waste management plan, a case study: The city of Belgrade

International Nuclear Information System (INIS)

Josimović, Boško; Marić, Igor; Milijić, Saša

2015-01-01

Highlights: • The paper deals with the specific method of multi-criteria evaluation applied in drafting the SEA for the Belgrade WMP. • MCE of the planning solutions, assessed according to 37 objectives of the SEA and four sets of criteria, was presented in the matrix form. • The results are presented in the form of graphs so as to be easily comprehensible to all the participants in the decision-making process. • The results represent concrete contribution proven in practice. - Abstract: Strategic Environmental Assessment (SEA) is one of the key instruments for implementing sustainable development strategies in planning in general; in addition to being used in sectoral planning, it can also be used in other areas such as waste management planning. SEA in waste management planning has become a tool for considering the benefits and consequences of the proposed changes in space, also taking into account the capacity of space to sustain the implementation of the planned activities. In order to envisage both the positive and negative implications of a waste management plan for the elements of sustainable development, an adequate methodological approach to evaluating the potential impacts must be adopted and the evaluation results presented in a simple and clear way, so as to allow planners to make relevant decisions as a precondition for the sustainability of the activities planned in the waste management sector. This paper examines the multi-criteria evaluation method for carrying out an SEA for the Waste Management Plan for the city of Belgrade (BWMP). The method was applied to the evaluation of the impacts of the activities planned in the waste management sector on the basis of the environmental and socioeconomic indicators of sustainability, taking into consideration the intensity, spatial extent, probability and frequency of impact, by means of a specific planning approach and simple and clear presentation of the obtained results

Multi-criteria evaluation in strategic environmental assessment for waste management plan, a case study: The city of Belgrade

Energy Technology Data Exchange (ETDEWEB)

Josimović, Boško, E-mail: bosko@iaus.ac.rs; Marić, Igor; Milijić, Saša

2015-02-15

Highlights: • The paper deals with the specific method of multi-criteria evaluation applied in drafting the SEA for the Belgrade WMP. • MCE of the planning solutions, assessed according to 37 objectives of the SEA and four sets of criteria, was presented in the matrix form. • The results are presented in the form of graphs so as to be easily comprehensible to all the participants in the decision-making process. • The results represent concrete contribution proven in practice. - Abstract: Strategic Environmental Assessment (SEA) is one of the key instruments for implementing sustainable development strategies in planning in general; in addition to being used in sectoral planning, it can also be used in other areas such as waste management planning. SEA in waste management planning has become a tool for considering the benefits and consequences of the proposed changes in space, also taking into account the capacity of space to sustain the implementation of the planned activities. In order to envisage both the positive and negative implications of a waste management plan for the elements of sustainable development, an adequate methodological approach to evaluating the potential impacts must be adopted and the evaluation results presented in a simple and clear way, so as to allow planners to make relevant decisions as a precondition for the sustainability of the activities planned in the waste management sector. This paper examines the multi-criteria evaluation method for carrying out an SEA for the Waste Management Plan for the city of Belgrade (BWMP). The method was applied to the evaluation of the impacts of the activities planned in the waste management sector on the basis of the environmental and socioeconomic indicators of sustainability, taking into consideration the intensity, spatial extent, probability and frequency of impact, by means of a specific planning approach and simple and clear presentation of the obtained results.

Post-disposal safety assessment of toxic and radioactive waste: waste types, disposal practices, disposal criteria, assessment methods and post-disposal impacts

International Nuclear Information System (INIS)

Torres, C.; Simon, I.; Little, R.H.; Charles, D.; Grogan, H.A.; Smith, G.M.; Sumerling, T.J.; Watkins, B.M.

1993-01-01

The need for safety assessments of waste disposal stems not only from the implementation of regulations requiring the assessment of environmental effects, but also from the more general need to justify decisions on protection requirements. As waste-disposal methods have become more technologically based, through the application of more highly engineered design concepts and through more rigorous and specific limitations on the types and quantities of the waste disposed, it follows that assessment procedures also must become more sophisticated. It is the overall aim of this study to improve the predictive modelling capacity for post-disposal safety assessments of land-based disposal facilities through the development and testing of a comprehensive, yet practicable, assessment framework. This report records all the work which has been undertaken during Phase 1 of the study. Waste types, disposal practices, disposal criteria and assessment methods for both toxic and radioactive waste are reviewed with the purpose of identifying those features relevant to assessment methodology development. Difference and similarities in waste types, disposal practices, criteria and assessment methods between countries, and between toxic and radioactive wastes are highlighted and discussed. Finally, an approach to identify post-disposal impacts, how they arise and their effects on humans and the environment is described

Environmental assessment for the construction, operation, and closure of the solid waste landfill at the Paducah Gaseous Diffusion Plant, Paducah, Kentucky

International Nuclear Information System (INIS)

1995-03-01

DOE has prepared an environmental assessment (EA) for the proposed construction, operation, and closure of a Solid Waste Landfill (SWL) that would be designed in accordance with Commonwealth of Kentucky landfill regulations (401 Kentucky Administrative Regulations Chapters 47 and 48 and Kentucky Revised Statutes 224.855). PGDP produces approximately 7,200 cubic yards per year of non-hazardous, non-radioactive solid waste currently being disposed of in a transitional contained (residential) landfill cell (Cell No. 3). New Kentucky landfill regulations mandate that all existing landfills be upgraded to meet the requirements of the new regulations or stop receiving wastes by June 30, 1995. Cell No. 3 must stop receiving wastes at that time and be closed and capped within 180 days after final receipt of wastes. The proposed SWL would occupy 25 acres of a 60-acre site immediately north of the existing PGDP landfill (Cell No. 3). The EA evaluated the potential environmental consequences of the proposed action and reasonable alternative actions. Based on the analysis in the EA, DOE has determined that the proposed action does not constitute a major Federal action which will significantly affect the human environment within the meaning of the National Environmental Policy Act of 1969 (NEPA), 42 USC 4321 et seq. Therefore, it is determined that an environmental impact statement will not be prepared, and DOE is issuing this FONSI

Environmental Management Assessment of the Stanford Linear Accelerator Center

International Nuclear Information System (INIS)

1994-01-01

This report documents the results of the Environmental Management Assessment of the Stanford Linear Accelerator Center (SLAC), Menlo Park, California. During this assessment, the activities conducted by the assessment team included reviews of internal documents and reports from previous assessments; interviews with the US Department of Energy (DOE), US Environmental Protection Agency, State Water Resources Board, California Regional Water Quality Control Board, and SLAC contractor personnel; and inspections and observations of selected facilities and operations. Onsite portion of the assessment was conducted from January 18 through January 31, 1994, by the DOE Office of Environmental Audit (EH-24), located within the Office of Environment, Safety and Health (EH), and the Environment and Safety Support Division (ESS), located within the Oakland Operations Office (OAK). The EH-24 environmental management assessment and the OAK functional appraisal were combined to minimize disruptions to the site. The management disciplines and three technical areas (air quality, groundwater, and inactive waste sites) were evaluated by EH-24, and four other technical areas (surface water, waste management, toxic and chemical materials, and environmental radiation) were assessed by ESS

Environmental assessment for the treatment of Class A low-level radioactive waste and mixed low-level waste generated by the West Valley Demonstration Project

International Nuclear Information System (INIS)

1995-11-01

The U.S. Department of Energy (DOE) is currently evaluating low-level radioactive waste management alternatives at the West Valley Demonstration Project (WVDP) located on the Western New York Nuclear Service Center (WNYNSC) near West Valley, New York. The WVDP's mission is to vitrify high-level radioactive waste resulting from commercial fuel reprocessing operations that took place at the WNYNSC from 1966 to 1972. During the process of high-level waste vitrification, low-level radioactive waste (LLW) and mixed low-level waste (MILLW) will result and must be properly managed. It is estimated that the WVDP's LLW storage facilities will be filled to capacity in 1996. In order to provide sufficient safe storage of LLW until disposal options become available and partially fulfill requirements under the Federal Facilities Compliance Act (FFCA), the DOE is proposing to use U.S. Nuclear Regulatory Commission-licensed and permitted commercial facilities in Oak Ridge, Tennessee; Clive, Utah; and Houston, Texas to treat (volume-reduce) a limited amount of Class A LLW and MLLW generated from the WVDP. Alternatives for ultimate disposal of the West Valley LLW are currently being evaluated in an environmental impact statement. This proposed action is for a limited quantity of waste, over a limited period of time, and for treatment only; this proposal does not include disposal. The proposed action consists of sorting, repacking, and loading waste at the WVDP; transporting the waste for commercial treatment; and returning the residual waste to the WVDP for interim storage. For the purposes of this assessment, environmental impacts were quantified for a five-year operating period (1996 - 2001). Alternatives to the proposed action include no action, construction of additional on-site storage facilities, construction of a treatment facility at the WVDP comparable to commercial treatment, and off-site disposal at a commercial or DOE facility

Assessing anaerobic co-digestion of pig manure with agroindustrial wastes: the link between environmental impacts and operational parameters.

Science.gov (United States)

Rodriguez-Verde, Ivan; Regueiro, Leticia; Carballa, Marta; Hospido, Almudena; Lema, Juan M

2014-11-01

Anaerobic co-digestion (AcoD) is established as a techno-economic profitable process by incrementing biogas yield (increased cost-efficiency) and improving the nutrient balance (better quality digestate) in comparison to mono-digestion of livestock wastes. However, few data are available on the environmental consequences of AcoD and most of them are mainly related to the use of energy crops as co-substrates. This work analysed the environmental impact of the AcoD of pig manure (PM) with several agroindustrial wastes (molasses, fish, biodiesel and vinasses residues) using life cycle assessment (LCA) methodology. For comparative purposes, mono digestion of PM has also been evaluated. Four out of six selected categories (acidification, eutrophication, global warming and photochemical oxidation potentials) showed environmental impacts in all the scenarios assessed, whereas the other two (abiotic depletion and ozone layer depletion potentials) showed environmental credits, remarking the benefit of replacing fossil fuels by biogas. This was also confirmed by the sensitivity analysis applied to the PM quality (i.e. organic matter content) and the avoided energy source demonstrating the importance of the energy recovery step. The influence of the type of co-substrate could not be discerned; however, a link between the environmental performance and the hydraulic retention time, the organic loading rate and the nutrient content in the digestate could be established. Therefore, LCA results were successfully correlated to process variables involved in AcoD, going a step further in the combination of techno-economic and environmental feasibilities. Copyright © 2014 Elsevier B.V. All rights reserved.

Environmental modelling of use of treated organic waste on agricultural land

DEFF Research Database (Denmark)

Hansen, Trine Lund; Christensen, Thomas Højlund; Schmidt, S.

2006-01-01

Modelling of environmental impacts from the application of treated organic municipal solid waste (MSW) in agriculture differs widely between different models for environmental assessment of waste systems. In this comparative study five models were examined concerning quantification and impact......, Denmark). DST and IWM are life cycle inventory (LCI) models, thus not performing actual impact assessment. The DST model includes only one water emission (biological oxygen demand) from compost leaching in the results and IWM considers only air emissions from avoided production of commercial fertilizers...... the different models and investigate the origin of any difference in type or magnitude of the results. The contributions from the LCI models were limited and did not depend on waste composition or local agricultural conditions. The three LCA models use the same overall approach for quantifying the impacts...

Environmental assessment [of nuclear installations

International Nuclear Information System (INIS)

Townsley, M.

1989-01-01

The European Community has introduced a directive which instructs that for all projects likely to have a significant effect on the environment consent should only be given after a rigorous assessment of such effects has been carried out and presented as an environmental statement. Projects requiring environmental assessment include nuclear power stations, any thermal power station over 300MW, any radioactive waste storage or disposal facility, any installation which produces electricity, power lines, installations for fuel production, fuel reprocessing, radioactive waste processing and fuel enrichment. The statement must include a description of the likely effects, direct and indirect, on the environment of the development, with reference to human beings, flora, fauna, soil, water, air, climate, landscape, interactions of two or more of these, material assets and cultural heritage. Measures to avoid or remedy the impact must be included. (U.K.)

An integrated risk assessment approach: Risk assessment in the programmatic environmental impact statement

International Nuclear Information System (INIS)

Morris, J.M.

1994-01-01

The following paper is an informal summary of salient points made in the presentation entitled open-quotes An Integrated Risk Assessment Approach: Risk Assessment in the Programmatic Environmental Impact Statement (PEIS).close quotes. This presentation was given at the U.S. DOE Integrated Planning Workshop in Denver, Colorado on June 2, 1994. Integrated decision analysis is very important in environmental restoration and waste management in the evaluation of such things as land use planning, waste load forecasting, cost analyses, and technology development activities. Integrated risk assessment is an approach that addresses multiple components of risk, including: risks from surplus facilities as well as typical environmental restoration sites, risks to the public, risks to workers, ecological risk, risks before, during and after remediation activities, and others

Environmental assessment of energy and waste systems based on anaerobic digestion

Energy Technology Data Exchange (ETDEWEB)

Rehl, Torsten

2013-08-01

The results of the studies show that biogas production brings about many or environmental improvements compared to energy generation based on fossil sources when designed and managed properly. Environmental advantages are found for GWP (Global Warming Potential) and energy consumption, disadvantages however for EP (Eutrophication Potential), AP (Acidification Potential) and POCP (Photochemical Ozone Creation Potential). However the large amount of technologies and measures indicate that there is a large potential to reduce the environmental impacts. Another finding is that all life cycle phases and subsystems must be carefully considered, as no single dominating item or aspect in the life cycle can be identified. The most environmentally relevant phases are found to be storage, treatment and field application of manure and digestate. This result is to a large part due to the emission of ammonia, nitrous oxide and nitrate. It can therefore be concluded that from a lifecycle perspective, control and mitigation of nitrogen related emissions will be of utmost importance in the future to improve the environmental performance of biogas systems. Considerable emission reduction potentials are exposed when proper technological modifications (e.g. storage covers, filter technologies, digestate treatment or field application technologies) or adopted management practices (early soil incorporation of digestate) are applied. The environmental analysis also shows that whenever possible the focus of anaerobic digestion should be on the use of organic residues from households, agriculture or food industry instead of using energy crops. In this case conventional waste management systems are replaced and manifold positive effects of anaerobic digestion such as waste stabilization, nutrient recycling and energy generation emerge.

The environmental impact of organic Rankine cycle for waste heat recovery through life-cycle assessment

International Nuclear Information System (INIS)

Liu, Chao; He, Chao; Gao, Hong; Xie, Hui; Li, Yourong; Wu, Shuangying; Xu, Jinliang

2013-01-01

The LCA (life-cycle assessment) was applied to evaluate EI (the environmental impact) of ORCPW (organic Rankine cycle power-plant for waste-heat-recovery) in this paper. The model of LCA on the ORCPW was established. The life-cycle of ORCPW was divided into construction, operation and decommissioning phases. The inventory of environmental emissions was listed for the ORCPW with 7 different working fluids. The GWP (global warming potential), AP (acidification potential), EP (eutrophication potential), HTP (human toxicity potential), SWP (solid waste potential) and SAP (soot and dust potential) were investigated. Some EIs of ORCPW were compared with the EIs of other power generation modes. The results show that the construction phase of ORCPW contributes mostly to the GWP and EP. GWP is the most serious EI followed by HTP among all the environmental impacts. The average pay back times of greenhouse gas discharged from ORCPW is calculated on the basis of five other power generation modes. For 7 different working fluids, it is 3–5 years for CO 2 , about one year for CH 4 and 3–6 years for NO x . But CO cannot be paid back during the life-cycle of ORCPW according to the average pay back time. - Highlights: • LCA was proposed to evaluate the environmental performance of ORC. • The ORC life cycle environmental emissions inventory was established. • GWP is the most serious environmental impact, followed by HTP. • The ORC with R113 exhibits the lowest environment impact load, followed by Pentane. • The total GWP of ORC could be paid back in 5 years

Co-ordination of federal and provincial environmental assessment processes for the Point Lepreau Generating Station Solid Radioactive Waste Management Facility modifications

Energy Technology Data Exchange (ETDEWEB)

Hickman, C.; Thompson, P.D. [Point Lepreau Generating Station, Point Lepreau Refurbishment Project, Lepreau, New Brunswick (Canada); Barnes, J. [Jacques Whitford Environment Ltd., Fredericton, New Brunswick (Canada)

2006-07-01

Modification of the Solid Radioactive Waste Management Facility at Point Lepreau Generating Station is required to accommodate waste generated during and after an 18-month maintenance outage during which the station would be Refurbished. The modification of the facility triggered both federal and provincial environmental assessment requirements, and these assessments were conducted in a 'coordinated' and cooperative fashion. In this project, the coordinated approach worked well, and provided some significant advantages to the proponent, the public and the regulators. However, there are opportunities for further improvement in future projects, and this paper explores the advantages and disadvantages of this 'co-ordinated' approach. As part of this exploration, there is a discussion of administrative and regulatory changes that the province is considering for the environmental assessment process, and a discussion of the need for a formal 'harmonization' agreement. (author)

Solid waste management of Jakarta : Indonesia an environmental systems perspective

OpenAIRE

Trisyanti, Dini

2004-01-01

Solid waste management has been one of the critical issues in Jakarta, Indonesia.With enormous amounts of generated waste per day and limited supportinginfrastructure, the city has faced serious threat of environmental deterioration andhealth hazard. It relies on one sanitary landfill only, whose capacity is currently beingexceeded, leading to excessive amounts of solid wastes left untreated in the city. An assessment with a system perspective was carried out, aiming to examine thecomplexity ...

Environmental assessment for the off-site volume reduction of low-level radioactive waste from the Savannah River Site

International Nuclear Information System (INIS)

1995-07-01

The Department of Energy (DOE) has prepared an environmental assessment (EA) (DOE/EA-1061) for the proposed off-site volume reduction of low-level radioactive wastes (LLW) generated at the Savannah River Site (SRS), near Aiken, South Carolina. Based on the analyses in the EA, DOE has determined that the proposed action is not a major Federal action significantly affecting the quality of the human environment within the meaning of the National Environmental Policy Act (NEPA) of 1969. Therefore, the preparation of an environmental impact statement (EIS) is not required, and DOE is issuing this Finding of No Significant Impact (FONSI)

Life cycle assessment of a national policy proposal - The case of a Swedish waste incineration tax

International Nuclear Information System (INIS)

Bjoerklund, Anna E.; Finnveden, Goeran

2007-01-01

At the core of EU and Swedish waste policy is the so-called waste hierarchy, according to which waste should first be prevented, but should otherwise be treated in the following order of prioritisation: reuse, recycling when environmentally motivated, energy recovery, and last landfilling. Some recent policy decisions in Sweden aim to influence waste management in the direction of the waste hierarchy. In 2001 a governmental commission assessed the economic and environmental impacts of introducing a weight-based tax on waste incineration, the purpose of which would be to encourage waste reduction and increase materials recycling and biological treatment. This paper presents the results of a life cycle assessment (LCA) of the waste incineration tax proposal. It was done in the context of a larger research project concerning the development and testing of a framework for Strategic Environmental Assessment (SEA). The aim of this paper is to assess the life cycle environmental impacts of the waste incineration tax proposal, and to investigate whether there are any possibilities of more optimal design of such a tax. The proposed design of the waste incineration tax results in increased recycling, but only in small environmental improvements. A more elaborate tax design is suggested, in which the tax level would partly be related to the fossil carbon content of the waste

Life-cycle assessment of municipal solid wastes: Development of the WASTED model

International Nuclear Information System (INIS)

Diaz, R.; Warith, M.

2006-01-01

This paper describes the development of the Waste Analysis Software Tool for Environmental Decisions (WASTED) model. This model provides a comprehensive view of the environmental impacts of municipal solid waste management systems. The model consists of a number of separate submodels that describe a typical waste management process: waste collection, material recovery, composting, energy recovery from waste and landfilling. These submodels are combined to represent a complete waste management system. WASTED uses compensatory systems to account for the avoided environmental impacts derived from energy recovery and material recycling. The model is designed to provide solid waste decision-makers and environmental researchers with a tool to evaluate waste management plans and to improve the environmental performance of solid waste management strategies. The model is user-friendly and compares favourably with other earlier models

Sandia National Laboratories performance assessment methodology for long-term environmental programs : the history of nuclear waste management.

Energy Technology Data Exchange (ETDEWEB)

Marietta, Melvin Gary; Anderson, D. Richard; Bonano, Evaristo J.; Meacham, Paul Gregory (Raytheon Ktech, Albuquerque, NM)

2011-11-01

Sandia National Laboratories (SNL) is the world leader in the development of the detailed science underpinning the application of a probabilistic risk assessment methodology, referred to in this report as performance assessment (PA), for (1) understanding and forecasting the long-term behavior of a radioactive waste disposal system, (2) estimating the ability of the disposal system and its various components to isolate the waste, (3) developing regulations, (4) implementing programs to estimate the safety that the system can afford to individuals and to the environment, and (5) demonstrating compliance with the attendant regulatory requirements. This report documents the evolution of the SNL PA methodology from inception in the mid-1970s, summarizing major SNL PA applications including: the Subseabed Disposal Project PAs for high-level radioactive waste; the Waste Isolation Pilot Plant PAs for disposal of defense transuranic waste; the Yucca Mountain Project total system PAs for deep geologic disposal of spent nuclear fuel and high-level radioactive waste; PAs for the Greater Confinement Borehole Disposal boreholes at the Nevada National Security Site; and PA evaluations for disposal of high-level wastes and Department of Energy spent nuclear fuels stored at Idaho National Laboratory. In addition, the report summarizes smaller PA programs for long-term cover systems implemented for the Monticello, Utah, mill-tailings repository; a PA for the SNL Mixed Waste Landfill in support of environmental restoration; PA support for radioactive waste management efforts in Egypt, Iraq, and Taiwan; and, most recently, PAs for analysis of alternative high-level radioactive waste disposal strategies including repositories deep borehole disposal and geologic repositories in shale and granite. Finally, this report summarizes the extension of the PA methodology for radioactive waste disposal toward development of an enhanced PA system for carbon sequestration and storage systems

The environmental comparison of landfilling vs. incineration of MSW accounting for waste diversion

International Nuclear Information System (INIS)

Assamoi, Bernadette; Lawryshyn, Yuri

2012-01-01

Highlights: ► Residential waste diversion initiatives are more successful with organic waste. ► Using a incineration to manage part of the waste is better environmentally. ► Incineration leads to more power plant emission offsets. ► Landfilling all of the waste would be preferred financially. - Abstract: This study evaluates the environmental performance and discounted costs of the incineration and landfilling of municipal solid waste that is ready for the final disposal while accounting for existing waste diversion initiatives, using the life cycle assessment (LCA) methodology. Parameters such as changing waste generation quantities, diversion rates and waste composition were also considered. Two scenarios were assessed in this study on how to treat the waste that remains after diversion. The first scenario is the status quo, where the entire residual waste was landfilled whereas in the second scenario approximately 50% of the residual waste was incinerated while the remainder is landfilled. Electricity was produced in each scenario. Data from the City of Toronto was used to undertake this study. Results showed that the waste diversion initiatives were more effective in reducing the organic portion of the waste, in turn, reducing the net electricity production of the landfill while increasing the net electricity production of the incinerator. Therefore, the scenario that incorporated incineration performed better environmentally and contributed overall to a significant reduction in greenhouse gas emissions because of the displacement of power plant emissions; however, at a noticeably higher cost. Although landfilling proves to be the better financial option, it is for the shorter term. The landfill option would require the need of a replacement landfill much sooner. The financial and environmental effects of this expenditure have yet to be considered.

Environmental-benefit analysis of two urban waste collection systems.

Science.gov (United States)

Aranda Usón, Alfonso; Ferreira, Germán; Zambrana Vásquez, David; Zabalza Bribián, Ignacio; Llera Sastresa, Eva

2013-10-01

Sustainable transportation infrastructure and travel policies aim to optimise the use of transportation systems to achieve economic and related social and environmental goals. To this end, a novel methodology based on life cycle assessment (LCA) has been developed in this study, with the aim of quantifying, in terms of CO2 emissions equivalent, the impact associated with different alternatives of waste collection systems in different urban typologies. This new approach is focussed on saving energy and raw materials and reducing the environmental impact associated with the waste collection system in urban areas, as well as allowing the design and planning of the best available technologies and most environment-friendly management. The methodology considers a large variety of variables from the point of view of sustainable urban transport such as the location and size of the urban area, the amount of solid waste generated, the level of social awareness on waste separation procedures, the distance between houses and waste collection points and the distance from the latter to the possible recovery plants and/or landfills, taking into account the material and energy recovery ratio within an integrated waste management system. As a case study, two different waste collection systems have been evaluated with this methodology in the ecocity Valdespartera located in Zaragoza, Spain, consisting of approximately 10,000 homes: (i) a system based on traditional truck transportation and manual collection, and (ii) a stationary vacuum waste collection system. Results show that, when operating at loads close to 100%, the stationary collection system has the best environmental performance in comparison with the conventional system. In contrast, when operating at load factors around 13% the environmental benefits in terms of net CO2-eq. emissions for the stationary collection system are around 60% lower in comparison with the conventional one. Copyright © 2013 Elsevier B.V. All

The environmental impact assessment of uranium mining in Australia

International Nuclear Information System (INIS)

Morvell, G.

2002-01-01

Federal environmental impact assessment legislation has existed in Australia since 1974. A number of uranium mines have been developed in this time, utilizing a range of mining techniques, including opencut, underground and in-situ leach. Projects have also been undertaken in a variety of geographical areas requiring consideration of diverse biodiversity, cultural heritage and social impact issues. Assessment of uranium mining proposals in Australia is also conducted in a climate of political opposition from a cross section of the Australian community. This paper outlines some of the key issues that arose during recent assessments and which provide a lead to the role of environmental impact assessment in environmental policy development. Issues are also relevant to recent assessments on a replacement nuclear reactor, shipments of waste for reprocessing and proposed assessments on proposals for low and intermediate level nuclear waste facilities. (author)

Low-level waste management alternatives and analysis in DOE`s programmatic environmental impact statement

Energy Technology Data Exchange (ETDEWEB)

Gerstein, J.S. [Dept. of Energy, Washington, DC (United States). Office of Environmental Restoration and Waste Management

1993-03-01

The Department of Energy is preparing a Programmatic Environmental Impact Statement (PEIS) for the Environmental Restoration and Waste Management Program. The PEIS has been divided into an Environmental Restoration section and a Waste Management section. Each section has a unique set of alternatives. This paper will focus on the waste management alternatives and analysis. The set of alternatives for waste management has been divided into waste categories. These categories are: high-level waste, transuranic waste, low-level waste, low-level mixed waste, greater-than-class C and low-level waste from commercial sources, hazardous waste, and spent nuclear fuel. This paper will discuss the alternatives and analytical approach that will be used to evaluate these alternatives for the low-level waste section. Although the same alternatives will be considered for all waste types, the analysis will be performed separately for each waste type. In the sections that follow, information will be provided on waste management configurations, the analysis of waste management alternatives, waste types and locations, facility and transportation activities, the facility and transportation impacts assessment, and the compilation of impacts.

Explanation of Significant Differences Between Models used to Assess Groundwater Impacts for the Disposal of Greater-Than-Class C Low-Level Radioactive Waste and Greater-Than-Class C-Like Waste Environmental Impact Statement (DOE/EIS-0375-D) and the

Energy Technology Data Exchange (ETDEWEB)

Annette Schafer; Arthur S. Rood; A. Jeffrey Sondrup

2011-08-01

Models have been used to assess the groundwater impacts to support the Draft Environmental Impact Statement for the Disposal of Greater-Than-Class C (GTCC) Low-Level Radioactive Waste and GTCC-Like Waste (DOE-EIS 2011) for a facility sited at the Idaho National Laboratory and the Environmental Assessment for the INL Remote-Handled Low-Level Waste Disposal Project (INL 2011). Groundwater impacts are primarily a function of (1) location determining the geologic and hydrologic setting, (2) disposal facility configuration, and (3) radionuclide source, including waste form and release from the waste form. In reviewing the assumptions made between the model parameters for the two different groundwater impacts assessments, significant differences were identified. This report presents the two sets of model assumptions and discusses their origins and implications for resulting dose predictions. Given more similar model parameters, predicted doses would be commensurate.

A case study of packaging waste collection systems in Portugal - Part II: Environmental and economic analysis.

Science.gov (United States)

Pires, Ana; Sargedas, João; Miguel, Mécia; Pina, Joaquim; Martinho, Graça

2017-03-01

An understanding of the environmental impacts and costs related to waste collection is needed to ensure that existing waste collection schemes are the most appropriate with regard to both environment and cost. This paper is Part II of a three-part study of a mixed packaging waste collection system (curbside plus bring collection). Here, the mixed collection system is compared to an exclusive curbside system and an exclusive bring system. The scenarios were assessed using life cycle assessment and an assessment of costs to the waste management company. The analysis focuses on the collection itself so as to be relevant to waste managers and decision-makers who are involved only in this step of the packaging life cycle. The results show that the bring system has lower environmental impacts and lower economic costs, and is capable of reducing the environmental impacts of the mixed system. However, a sensitivity analysis shows that these results could differ if the curbside collection were to be optimized. From economic and environmental perspectives, the mixed system has few advantages. Copyright © 2016 Elsevier Ltd. All rights reserved.

Assessment of LANL waste minimization plan

International Nuclear Information System (INIS)

Davis, K.D.; McNair, D.A.; Jennrich, E.A.; Lund, D.M.

1991-04-01

The objective of this report is to evaluate the Los Alamos National Laboratory (LANL) Waste Minimization Plan to determine if it meets applicable internal (DOE) and regulatory requirements. The intent of the effort is to assess the higher level elements of the documentation to determine if they have been addressed rather than the detailed mechanics of the program's implementation. The requirement for a Waste Minimization Plan is based in several DOE Orders as well as environmental laws and regulations. Table 2-1 provides a list of the major documents or regulations that require waste minimization efforts. The table also summarizes the applicable requirements

Multi-criteria evaluation in strategic environmental assessment for waste management plan, a case study: the city of Belgrade.

Science.gov (United States)

Josimović, Boško; Marić, Igor; Milijić, Saša

2015-02-01

Strategic Environmental Assessment (SEA) is one of the key instruments for implementing sustainable development strategies in planning in general; in addition to being used in sectoral planning, it can also be used in other areas such as waste management planning. SEA in waste management planning has become a tool for considering the benefits and consequences of the proposed changes in space, also taking into account the capacity of space to sustain the implementation of the planned activities. In order to envisage both the positive and negative implications of a waste management plan for the elements of sustainable development, an adequate methodological approach to evaluating the potential impacts must be adopted and the evaluation results presented in a simple and clear way, so as to allow planners to make relevant decisions as a precondition for the sustainability of the activities planned in the waste management sector. This paper examines the multi-criteria evaluation method for carrying out an SEA for the Waste Management Plan for the city of Belgrade (BWMP). The method was applied to the evaluation of the impacts of the activities planned in the waste management sector on the basis of the environmental and socioeconomic indicators of sustainability, taking into consideration the intensity, spatial extent, probability and frequency of impact, by means of a specific planning approach and simple and clear presentation of the obtained results. Copyright © 2014 Elsevier Ltd. All rights reserved.

Industrial ecology: Environmental chemistry and hazardous waste

Energy Technology Data Exchange (ETDEWEB)

Manahan, S.E. [Univ. of Missouri, Columbia, MO (United States). Dept. of Chemistry

1999-01-01

Industrial ecology may be a relatively new concept -- yet it`s already proven instrumental for solving a wide variety of problems involving pollution and hazardous waste, especially where available material resources have been limited. By treating industrial systems in a manner that parallels ecological systems in nature, industrial ecology provides a substantial addition to the technologies of environmental chemistry. Stanley E. Manahan, bestselling author of many environmental chemistry books for Lewis Publishers, now examines Industrial Ecology: Environmental Chemistry and Hazardous Waste. His study of this innovative technology uses an overall framework of industrial ecology to cover hazardous wastes from an environmental chemistry perspective. Chapters one to seven focus on how industrial ecology relates to environmental science and technology, with consideration of the anthrosphere as one of five major environmental spheres. Subsequent chapters deal specifically with hazardous substances and hazardous waste, as they relate to industrial ecology and environmental chemistry.

Waste management, decommissioning and environmental restoration for Canada's nuclear activities. Proceedings

International Nuclear Information System (INIS)

2011-01-01

The Canadian Nuclear Society conference on Waste Management, Decommissioning and Environmental Restoration for Canada's Nuclear Activities was held in Toronto, Ontario, Canada on September 11-14, 2011. The conference provided a forum for discussion of the status and proposed future directions of technical, regularly, environmental, social and economic aspects of radioactive waste management, nuclear facility decommissioning, and environmental restoration activities for Canadian nuclear facilities. The conference included both plenary sessions and sessions devoted to more detailed technical issues. The plenary sessions were focussed on three broad themes: the overall Canadian program; low and intermediate waste; and, international perspectives. Topics of the technical sessions included: OPG's deep geologic repository for low and intermediate level waste; stakeholder interactions; decommissioning projects; uranium mine waste management; used fuel repository - design and safety assessment; federal policies, programs and oversight; regulatory considerations; aboriginal traditional knowledge; geological disposal - CRL site classification; geological disposal - modelling and engineered barriers; Port Hope Area Initiative; waste characterization; LILWM - treatment and processing; decommissioning projects and information management; international experience; environmental remediation; fuel cycles and waste processing.

Nuclear waste disposal: technology and environmental hazards

International Nuclear Information System (INIS)

Hare, F.K.; Aikin, A.M.

1980-01-01

The subject is discussed under the headings: introduction; the nature and origin of wastes (fuel cycles; character of wastes; mining and milling operations; middle stages; irradiated fuel; reprocessing (waste generation); reactor wastes); disposal techniques and disposal of reprocessing wastes; siting of repositories; potential environmental impacts (impacts after emplacement in a rock repository; catastrophic effects; dispersion processes (by migrating ground water); thermal effects; future security; environmental survey, monitoring and modelling); conclusion. (U.K.)

Assessing the environmental sustainability of energy recovery from municipal solid waste in the UK.

Science.gov (United States)

Jeswani, H K; Azapagic, A

2016-04-01

Even though landfilling of waste is the least favourable option in the waste management hierarchy, the majority of municipal solid waste (MSW) in many countries is still landfilled. This represents waste of valuable resources and could lead to higher environmental impacts compared to energy recovered by incineration, even if the landfill gas is recovered. Using life cycle assessment (LCA) as a tool, this paper aims to find out which of the following two options for MSW disposal is more environmentally sustainable: incineration or recovery of biogas from landfills, each producing either electricity or co-generating heat and electricity. The systems are compared on a life cycle basis for two functional units: 'disposal of 1 tonne of MSW' and 'generation of 1 kWh of electricity'. The results indicate that, if both systems are credited for their respective recovered energy and recyclable materials, energy from incineration has much lower impacts than from landfill biogas across all impact categories, except for human toxicity. The impacts of incineration co-generating heat and electricity are negative for nine out of 11 categories as the avoided impacts for the recovered energy and materials are higher than those caused by incineration. By improving the recovery rate of biogas, some impacts of landfilling, such as global warming, depletion of fossil resources, acidification and photochemical smog, would be significantly reduced. However, most impacts of the landfill gas would still be higher than the impacts of incineration, except for global warming and human toxicity. The analysis on the basis of net electricity produced shows that the LCA impacts of electricity from incineration are several times lower in comparison to the impacts of electricity from landfill biogas. Electricity from incineration has significantly lower global warming and several other impacts than electricity from coal and oil but has higher impacts than electricity from natural gas or UK grid. At

Life cycle assessment applied to nanomaterials in solid waste management

DEFF Research Database (Denmark)

Laurent, Alexis

While the generation of solid waste is globally increasing, much effort is concentrated to minimise the environmental impacts related to their management. With respect to nanoproducts (products containing nanomaterials), a growing amount of ‘nanowaste’ can be expected to enter the waste streams...... on specific waste types and waste management systems, all primarily reflecting situations in economicallydeveloped countries. At the same time, methodological practice was found in many studies not to be compliant with current reference guidance, such as the ISO standards and the ILCD Handbook. Likewise......, thus potentially posing problems on human health, e.g. through occupational exposure to engineered nanoparticles. In that setting, through its holistic quantification of environmental impacts, life cycle assessment (LCA) can be a useful decisionsupport tool for managing environmental sustainability...

Quarterly Briefing Book on Environmental and Waste Management Activities

Energy Technology Data Exchange (ETDEWEB)

Brown, M.C.

1991-06-01

The purpose of the Quarterly Briefing Book on Environmental and Waste Management Activities is to provide managers and senior staff at the US Department of Energy-Richland Operations Office and its contractors with timely and concise information on Hanford Site environmental and waste management activities. Each edition updates the information on the topics in the previous edition, deletes those determined not to be of current interest, and adds new topics to keep up to date with changing environmental and waste management requirements and issues. Section A covers current waste management and environmental restoration issues. In Section B are writeups on national or site-wide environmental and waste management topics. Section C has writeups on program- and waste-specific environmental and waste management topics. Section D provides information on waste sites and inventories on the site. 15 figs., 4 tabs.

Quarterly Briefing Book on Environmental and Waste Management Activities

International Nuclear Information System (INIS)

Brown, M.C.

1991-06-01

The purpose of the Quarterly Briefing Book on Environmental and Waste Management Activities is to provide managers and senior staff at the US Department of Energy-Richland Operations Office and its contractors with timely and concise information on Hanford Site environmental and waste management activities. Each edition updates the information on the topics in the previous edition, deletes those determined not to be of current interest, and adds new topics to keep up to date with changing environmental and waste management requirements and issues. Section A covers current waste management and environmental restoration issues. In Section B are writeups on national or site-wide environmental and waste management topics. Section C has writeups on program- and waste-specific environmental and waste management topics. Section D provides information on waste sites and inventories on the site. 15 figs., 4 tabs

Life cycle assessment of urban waste management: energy performances and environmental impacts. The case of Rome, Italy.

Science.gov (United States)

Cherubini, Francesco; Bargigli, Silvia; Ulgiati, Sergio

2008-12-01

Landfilling is nowadays the most common practice of waste management in Italy in spite of enforced regulations aimed at increasing waste pre-sorting as well as energy and material recovery. In this work we analyse selected alternative scenarios aimed at minimizing the unused material fraction to be delivered to the landfill. The methodological framework of the analysis is the life cycle assessment, in a multi-method form developed by our research team. The approach was applied to the case of municipal solid waste (MSW) management in Rome, with a special focus on energy and material balance, including global and local scale airborne emissions. Results, provided in the form of indices and indicators of efficiency, effectiveness and environmental impacts, point out landfill activities as the worst waste management strategy at a global scale. On the other hand, the investigated waste treatments with energy and material recovery allow important benefits of greenhouse gas emission reduction (among others) but are still affected by non-negligible local emissions. Furthermore, waste treatments leading to energy recovery provide an energy output that, in the best case, is able to meet 15% of the Rome electricity consumption.

Life cycle assessment of urban waste management: Energy performances and environmental impacts. The case of Rome, Italy

International Nuclear Information System (INIS)

Cherubini, Francesco; Bargigli, Silvia; Ulgiati, Sergio

2008-01-01

Landfilling is nowadays the most common practice of waste management in Italy in spite of enforced regulations aimed at increasing waste pre-sorting as well as energy and material recovery. In this work we analyse selected alternative scenarios aimed at minimizing the unused material fraction to be delivered to the landfill. The methodological framework of the analysis is the life cycle assessment, in a multi-method form developed by our research team. The approach was applied to the case of municipal solid waste (MSW) management in Rome, with a special focus on energy and material balance, including global and local scale airborne emissions. Results, provided in the form of indices and indicators of efficiency, effectiveness and environmental impacts, point out landfill activities as the worst waste management strategy at a global scale. On the other hand, the investigated waste treatments with energy and material recovery allow important benefits of greenhouse gas emission reduction (among others) but are still affected by non-negligible local emissions. Furthermore, waste treatments leading to energy recovery provide an energy output that, in the best case, is able to meet 15% of the Rome electricity consumption

Environmental and health impacts of using food waste as animal feed: a comparative analysis of food waste management options.

Science.gov (United States)

Salemdeeb, Ramy; Zu Ermgassen, Erasmus K H J; Kim, Mi Hyung; Balmford, Andrew; Al-Tabbaa, Abir

2017-01-01

The disposal of food waste is a large environmental problem. In the United Kingdom (UK), approximately 15 million tonnes of food are wasted each year, mostly disposed of in landfill, via composting, or anaerobic digestion (AD). European Union (EU) guidelines state that food waste should preferentially be used as animal feed though for most food waste this practice is currently illegal, because of disease control concerns. Interest in the potential diversion of food waste for animal feed is however growing, with a number of East Asian states offering working examples of safe food waste recycling - based on tight regulation and rendering food waste safe through heat treatment. This study investigates the potential benefits of diverting food waste for pig feed in the UK. A hybrid, consequential life cycle assessment (LCA) was conducted to compare the environmental and health impacts of four technologies for food waste processing: two technologies of South Korean style-animal feed production (as a wet pig feed and a dry pig feed) were compared with two widespread UK disposal technologies: AD and composting. Results of 14 mid-point impact categories show that the processing of food waste as a wet pig feed and a dry pig feed have the best and second-best scores, respectively, for 13/14 and 12/14 environmental and health impacts. The low impact of food waste feed stems in large part from its substitution of conventional feed, the production of which has substantial environmental and health impacts. While the re-legalisation of the use of food waste as pig feed could offer environmental and public health benefits, this will require support from policy makers, the public, and the pig industry, as well as investment in separated food waste collection which currently occurs in only a minority of regions.

Minimizing waste in environmental restoration

International Nuclear Information System (INIS)

Thuot, J.R.; Moos, L.

1996-01-01

Environmental restoration, decontamination and decommissioning, and facility dismantlement projects are not typically known for their waste minimization and pollution prevention efforts. Typical projects are driven by schedules and milestones with little attention given to cost or waste minimization. Conventional wisdom in these projects is that the waste already exists and cannot be reduced or minimized; however, there are significant areas where waste and cost can be reduced by careful planning and execution. Waste reduction can occur in three ways: beneficial reuse or recycling, segregation of waste types, and reducing generation of secondary waste

Supplemental environmental impact statement - defense waste processing facility

International Nuclear Information System (INIS)

1994-11-01

This document supplements the Final Environmental Impact Statement (EIS) DOE Issued in 1982 (DOE/EIS-0082) to construct and operate the Defense Waste Processing Facility (DWPF) at the Savannah River Site (SRS), a major DOE installation in southwestern South Carolina. That EIS supported the decision to construct and operate the DWPF to immobilize high-level waste generated as a result of nuclear materials processing at SRS. The DWPF would use a vitrification process to incorporate the radioactive waste into borosilicate glass and seal it in stainless steel canisters for eventual disposal at a permanent geologic repository. The DWPF is now mostly constructed and nearly ready for full operation. However, DOE has made design changes to the DWPF since the 1982 EIS to improve efficiency and safety of the facility. Each of these modifications was subjected to appropriate NEPA review. The purpose of this Supplemental EIS is to assist DOE in deciding whether and how to proceed with operation of the DWPF as modified since 1982 while ensuring appropriate consideration of potential environmental effects. In this document, DOE assesses the potential environmental impacts of completing and operating the DWPF in light of these design changes, examines the impact of alternatives, and identifies potential actions to be taken to reduce adverse impacts. Evaluations of impacts on water quality, air quality, ecological systems, land use, geologic resources, cultural resources, socioeconomics, and health and safety of onsite workers and the public are included in the assessment

The Waste Isolation Pilot Plant Performance Assessment Program

International Nuclear Information System (INIS)

Myers, J.; Coons, W.E.; Eastmond, R.; Morse, J.; Chakrabarti, S.; Zurkoff, J.; Colton, I.D.; Banz, I.

1986-01-01

The Waste Isolation Pilot Plant (WIPP) Performance Assessment Program involves a comprehensive analysis of the WIPP project with respect to the recently finalized Environmental Protection Agency regulations regarding the long-term geologic isolation of radioactive wastes. The performance assessment brings together the results of site characterization, underground experimental, and environmental studies into a rigorous determination of the performance of WIPP as a disposal system for transuranic radioactive waste. The Program consists of scenario development, geochemical, hydrologic, and thermomechanical support analyses and will address the specific containment and individual protection requirements specified in 40 CFR 191 sub-part B. Calculated releases from these interrelated analyses will be reported as an overall probability distribution of cumulative release resulting from all processes and events occurring over the 10,000 year post-closure period. In addition, results will include any doses to the public resulting from natural processes occurring over the 1,000 year post-closure period. The overall plan for the WIPP Performance Assessment Program is presented along with approaches to issues specific to the WIPP project

Converting lignocellulosic solid waste into ethanol for the State of Washington: an investigation of treatment technologies and environmental impacts.

Science.gov (United States)

Schmitt, Elliott; Bura, Renata; Gustafson, Rick; Cooper, Joyce; Vajzovic, Azra

2012-01-01

There is little research literature on the conversion of lignocellulosic rich waste streams to ethanol, and even fewer have investigated both the technical aspects and environmental impacts together. This study assessed technical and environmental challenges of converting three lignocellulosic waste streams to ethanol: municipal solid waste (MSW), low grade mixed waste paper (MWP), and organic yard waste (YW). Experimental results showed high conversion yields for all three streams using suitable conversion methods. Environmental impacts are highly dependent on conversion technology, and process conditions used. Life cycle assessment results showed that both chemicals production and waste collection are important factors to be included within a waste-to-ethanol study. Copyright © 2011 Elsevier Ltd. All rights reserved.

Preliminary environmental site assessments in New York City

International Nuclear Information System (INIS)

Lundy, P.; Gasson, D.R.; Longendyke, S.T.

1991-01-01

Preliminary Environmental Site Assessments are often performed prior to real estate transactions or refinancing. These assessments are typically performed for real estate buyers, sellers and lending institutions. Undertaking a Preliminary Environmental Site Assessment in New York City can often be quite complex and time-consuming. This is due, in part, to the age and density of buildings in the city as well as the myriad of regulatory agencies with jurisdiction over environmental issues. This paper will discuss how environmental assessments are performed with a special emphasis on building in New York City. In includes hazardous wastes management for Radon, PCB's and asbestos

Criteria and principles for environmental assessment of disposal of radioactive wastes

International Nuclear Information System (INIS)

Hill, M.D.

1989-01-01

This paper describes the criteria which are used in judging whether methods for the disposal of radioactive wastes are acceptable, from a radiological protection point of view, and the principles used in assessing the radiological impact of waste disposal methods. Gaseous, liquid and solid wastes are considered, and the discussion is relevant to wastes arising from the nuclear power industry, and from medical practices, general industry and research. Throughout the paper, emphasis is given to the general criteria and principles recommended by international organizations rather than to the detailed legislative and regulatory requirements in particular countries

Transportation risk assessment for the US Department of Energy Environmental Management Programmatic Environmental Impact Statement

International Nuclear Information System (INIS)

Chen, S.Y.; Monette, F.A.; Biwer, B.M.; Lazaro, M.A.; Hartmann, H.M.; Policastro, A.J.

1994-01-01

In its Programmatic Environmental Impact Statement (PEIS), the Office of Environmental Management (EM) of the US Department of Energy (DOE) is considering a broad range of alternatives for the future management of radioactive and hazardous waste at the facilities of the DOE complex. The alternatives involve facilities to be used for treatment, storage, and disposal of various wastes generated from DOE's environmental restoration activities and waste management operation. Included in the evaluation are six types of waste (five types of radioactive waste plus hazardous waste), 49 sites, and numerous cases associated with each different alternative for waste management. In general, the alternatives are evaluated independently for each type of waste and reflect decentralized, regionalized, and centralized approaches. Transportation of waste materials is an integral component of the EM PEIS alternatives for waste management. The estimated impact on human health that is associated with various waste transportation activities is an important element leading to a complete appraisal of the alternatives. The transportation risk assessment performed for the EM PEIS is designed to ensure -- through uniform and judicious selection of models, data, and assumptions -- that relative comparisons of risk among the various alternatives are meaningful and consistent

Environmental Change in Post-closure Safety Assessment of Solid Radioactive Waste Repositories. Report of Working Group 3 Reference Models for Waste Disposal of EMRAS II Topical Heading Reference Approaches for Human Dose Assessment. Environmental Modelling for Radiation Safety (EMRAS II) Programme

International Nuclear Information System (INIS)

2016-08-01

Environmental assessment models are used for evaluating the radiological impact of actual and potential releases of radionuclides to the environment. They are essential tools for use in the regulatory control of routine discharges to the environment and also in planning measures to be taken in the event of accidental releases. They are also used for predicting the impact of releases which may occur far into the future, for example, from underground radioactive waste repositories. It is important to verify, to the extent possible, the reliability of the predictions of such models by a comparison with measured values in the environment or with predictions of other models. The IAEA has been organizing programmes of international model testing since the 1980s. These programmes have contributed to a general improvement in models, in the transfer of data and in the capabilities of modellers in Member States. IAEA publications on this subject over the past three decades demonstrate the comprehensive nature of the programmes and record the associated advances which have been made. From 2009 to 2011, the IAEA organized a programme entitled Environmental Modelling for Radiation Safety (EMRAS II), which concentrated on the improvement of environmental transfer models and the development of reference approaches to estimate the radiological impacts on humans, as well as on flora and fauna, arising from radionuclides in the environment. Different aspects were addressed by nine working groups covering three themes: reference approaches for human dose assessment, reference approaches for biota dose assessment and approaches for assessing emergency situations. This publication describes the work of the Reference Models for Waste Disposal Working Group

Radiation environmental impact assessment of the radioisotope's application on nuclear medical science

International Nuclear Information System (INIS)

Liu Hongshi

2004-01-01

The radiation environmental impact assessment of the radioisotope's application on nuclear medical science is introduced, including the assessment criteria, the assessment methods and the environmental impact assessment of three wastes emission. (authors)

Environmental and economic life cycle analysis of plastic waste management options. A review

OpenAIRE

Bernardo, C. A.; Simões, Carla L.; Pinto, Lígia

2016-01-01

In recent years, rising worldwide plastic consumption led to the generation of increasing amounts of plastic waste and to the awareness of the importance of its management. In that framework, the present work describes how Life Cycle Assessment (LCA) and economic assessment methodologies can be used for evaluating environmental and economic impacts of alternative plastic waste management systems. The literature on LCA of plastic waste management systems is vast and the results reported are ge...

A holistic approach to the environmental evaluation of food waste prevention.

Science.gov (United States)

Salemdeeb, Ramy; Font Vivanco, David; Al-Tabbaa, Abir; Zu Ermgassen, Erasmus K H J

2017-01-01

The environmental evaluation of food waste prevention is considered a challenging task due to the globalised nature of the food supply chain and the limitations of existing evaluation tools. The most significant of these is the rebound effect: the associated environmental burdens of substitutive consumption that arises as a result of economic savings made from food waste prevention. This study introduces a holistic approach to addressing these challenges, with a focus on greenhouse gas (GHG) emissions from household food waste in the UK. It uses a hybrid life-cycle assessment model coupled with a highly detailed multi-regional environmentally extended input output analysis to capture environmental impacts across the global food supply chain. The study also takes into consideration the rebound effect, which was modelled using a linear specification of an almost ideal demand system. The study finds that food waste prevention could lead to substantial reductions in GHG emissions in the order of 706-896kg CO 2 -eq. per tonne of food waste, with most of these savings (78%) occurring as a result of avoided food production overseas. The rebound effect may however reduce such GHG savings by up to 60%. These findings provide a deeper insight into our understanding of the environmental impacts of food waste prevention: the study demonstrates the need to adopt a holistic approach when developing food waste prevention policies in order to mitigate the rebound effect and highlight the importance of increasing efficiency across the global food supply chain, particularly in developing countries. Copyright © 2016 Elsevier Ltd. All rights reserved.

Hanford immobilized low-activity tank waste performance assessment

International Nuclear Information System (INIS)

Mann, F.M.

1998-01-01

The Hanford Immobilized Low-Activity Tank Waste Performance Assessment examines the long-term environmental and human health effects associated with the planned disposal of the vitrified low-level fraction of waste presently contained in Hanford Site tanks. The tank waste is the by-product of separating special nuclear materials from irradiated nuclear fuels over the past 50 years. This waste has been stored in underground single and double-shell tanks. The tank waste is to be retrieved, separated into low and high-activity fractions, and then immobilized by private vendors. The US Department of Energy (DOE) will receive the vitrified waste from private vendors and plans to dispose of the low-activity fraction in the Hanford Site 200 East Area. The high-level fraction will be stored at Hanford until a national repository is approved. This report provides the site-specific long-term environmental information needed by the DOE to issue a Disposal Authorization Statement that would allow the modification of the four existing concrete disposal vaults to provide better access for emplacement of the immobilized low-activity waste (ILAW) containers; filling of the modified vaults with the approximately 5,000 ILAW containers and filler material with the intent to dispose of the containers; construction of the first set of next-generation disposal facilities. The performance assessment activity will continue beyond this assessment. The activity will collect additional data on the geotechnical features of the disposal sites, the disposal facility design and construction, and the long-term performance of the waste. Better estimates of long-term performance will be produced and reviewed on a regular basis. Performance assessments supporting closure of filled facilities will be issued seeking approval of those actions necessary to conclude active disposal facility operations. This report also analyzes the long-term performance of the currently planned disposal system as a basis

Hanford immobilized low-activity tank waste performance assessment

Energy Technology Data Exchange (ETDEWEB)

Mann, F.M.

1998-03-26

The Hanford Immobilized Low-Activity Tank Waste Performance Assessment examines the long-term environmental and human health effects associated with the planned disposal of the vitrified low-level fraction of waste presently contained in Hanford Site tanks. The tank waste is the by-product of separating special nuclear materials from irradiated nuclear fuels over the past 50 years. This waste has been stored in underground single and double-shell tanks. The tank waste is to be retrieved, separated into low and high-activity fractions, and then immobilized by private vendors. The US Department of Energy (DOE) will receive the vitrified waste from private vendors and plans to dispose of the low-activity fraction in the Hanford Site 200 East Area. The high-level fraction will be stored at Hanford until a national repository is approved. This report provides the site-specific long-term environmental information needed by the DOE to issue a Disposal Authorization Statement that would allow the modification of the four existing concrete disposal vaults to provide better access for emplacement of the immobilized low-activity waste (ILAW) containers; filling of the modified vaults with the approximately 5,000 ILAW containers and filler material with the intent to dispose of the containers; construction of the first set of next-generation disposal facilities. The performance assessment activity will continue beyond this assessment. The activity will collect additional data on the geotechnical features of the disposal sites, the disposal facility design and construction, and the long-term performance of the waste. Better estimates of long-term performance will be produced and reviewed on a regular basis. Performance assessments supporting closure of filled facilities will be issued seeking approval of those actions necessary to conclude active disposal facility operations. This report also analyzes the long-term performance of the currently planned disposal system as a basis

Environmental assessment of incinerator residue utilisation

OpenAIRE

Toller, Susanna; Kärrman, Erik; Gustafsson, Jon Petter; Magnusson, Y.

2009-01-01

Incineration ashes may be treated either as a waste to be dumped in landfill, or as a resource that is suit able for re-use. In order to choose the best management scenario, knowledge is needed on the potential environmental impact that may be expected, including not only local, but also regional and global impact. In this study. A life cycle assessment (LCA) based approach Was Outlined for environmental assessment of incinerator residue utilisation, in which leaching of trace elements as wel...

Risky business: Assessing cleanup plans for waste sites

International Nuclear Information System (INIS)

Blaylock, B.

1995-01-01

ORNL was chosen to perform human health and ecological risk assessments for DOE because of its risk assessment expertise. The U.S. Department of Energy's many production and research sites contain radioactive and hazardous wastes. These waste sites pose potential risks to the health and safety of remediation and waste management workers and the public. The risks, however, vary from site to site. Some sites undoubtedly present larger risks than others and should be cleaned up first. However, before the cleanup begins, DOE is required by law to prepare an environmental impact statement on any actions that may significantly affect the environment-even actions that would clean it up

Minimizing waste in environmental restoration

International Nuclear Information System (INIS)

Moos, L.; Thuot, J.R.

1996-01-01

Environmental restoration, decontamination and decommissioning and facility dismantelment projects are not typically known for their waste minimization and pollution prevention efforts. Typical projects are driven by schedules and milestones with little attention given to cost or waste minimization. Conventional wisdom in these projects is that the waste already exists and cannot be reduced or minimized. In fact, however, there are three significant areas where waste and cost can be reduced. Waste reduction can occur in three ways: beneficial reuse or recycling; segregation of waste types; and reducing generation of secondary waste. This paper will discuss several examples of reuse, recycle, segregation, and secondary waste reduction at ANL restoration programs

Environmental impact assessment and socio political issues of nuclear waste management; Ydinjaetehuollon ympaeristoevaikutusten arviointi ja sosiopoliittiset kysymykset

Energy Technology Data Exchange (ETDEWEB)

Harmaajaervi, I; Tolsa, H [VTT Communities and Infrastructure, Espoo (Finland). Urban Planning; Vuori, S [VTT Energy, Espoo (Finland). Nuclear Energy; Litmanen, T [Jyvaeskylae Univ. (Finland)

1997-09-01

The study is a part of the Publicly Administrated Nuclear Waste Management Research Programme (JYT2) which was carried out in 1994-1996. The principal goal of the research programme has been to provide the authorities with information and research results relevant for the safety of nuclear waste management in order to support the various activities of the authorities. The main emphasis of the research programme focuses on the disposal of spent fuel. In addition to nuclear waste research in the field of natural sciences and technology, the research program- me has focused mostly on societal issues associated with nuclear waste disposal facilities and on the non-radiological environmental effects in the environs of the disposal site. Some of the local effects are already revealed in the research phase, before any final decisions are made as to the selection of the disposal site. The study has focused primarily on local and regional issues. The statutory requirement to conduct environ- mental impact assessment (EIA) chiefly concerns those who are responsible for waste management, but the authorities also need to acquire systematic information in the field to support developing requirements for the content and scope of EIA procedure and preparedness to check the assessments made. This is a report of the first parts of the study in 1994-1995. The report deals with the subject matter generally based on earlier studies in Finland and other countries. The results of the study will be reported later. 101 refs.

Discussion of some issues in assessing nuclear and radiation environmental impacts and in related assessment

International Nuclear Information System (INIS)

Pan Ziqiang

1998-01-01

The author discusses some noticeable issues in drafting assessment report of nuclear and radiation environmental impacts and relevant aspects needed to be considered from the point of view of comprehensive environmental assessment. The considerable issue are principles of radioactive waste management, optimization of radiation protection and collective dose, and uncertainty of the assessment. Implementing reporting system on assessment of nuclear and radiation environmental impacts would improve environmental protection for nuclear and radiation facilities. However, trade's, regional , country and global assessment of environmental impacts has to be enhanced. For this purpose, it is necessary to develop methodology of qualitative and quantitative comprehensive assessment

E-waste: Environmental Problems and Current Management

Directory of Open Access Journals (Sweden)

D. Aktsoglou

2010-01-01

Full Text Available In this paper the environmental problems related with the discarded electronic appliances, known as e-waste, are reviewed.Moreover, the current and the future production of e-waste, the potential environmental problems associated with theirdisposal and management practices are discussed whereas the existing e-waste management schemes in Greece and othercountries (Japan, Switzerland are also quoted.

Disposal facility for spent nuclear fuel. Environmental impact assessment program

International Nuclear Information System (INIS)

1998-01-01

The report presents the Environmental Impact Assessment (EIA) of the high level radioactive waste disposal in Finland. In EIA different alternatives concerning site selection, construction, operation and sealing of the disposal facility as well as waste transportation and encapsulation of the waste are considered

Waste diminution in Construction projects: Environmental Predicaments

Science.gov (United States)

Gharehbaghi, Koorosh; Scott-Young, Christina

2018-03-01

Waste diminution in construction projects is not only a behavioural issue, but also an energy consumption and reduction concern. With construction waste equating to the significant amount of exhausted energy together with increased pollution, this contributes to a series of environmental predicaments. The overall goal of construction solid Waste Management is to collect, treat and dispose of solid wastes generated by project activities in an environmentally and socially satisfactory manner, using the most economical means available. As cities expand, their construction activities and consumption patterns further drive up the solid waste quantities. Governments are usually authorized to have responsibility for providing solid Waste Management services, and various administrative laws give them exclusive ownership over the waste produced. In addition, construction waste processing can be further controlled and minimized according to specialized authorities such as Environmental Protection Agencies (EPA) and their relevant acts and regulations. Moreover, a Construction Environmental Management Plan (CEMP) can further control the treatment of waste and therefore, reduce the amount produced. Key elements of a CEMP not only include complying with relevant legislation, standards and guidance from the EPA; however, also to ensuring that there are systems in place to resolve any potential problems associated with site activities. Accordingly, as a part of energy consumption and lessening strategies, this paper will discuss various effective waste reduction methods for construction projects. Finally, this paper will also examine tactics to further improve energy efficiency through innovative construction Waste Management strategies (including desirability rating of most favourable options) to promote the lessening of overall CO2production.

US Environmental Protection Agency's assessment of environmental impacts of TENORM radiation sources: The example of uranium mining TENORM wastes

International Nuclear Information System (INIS)

Setlow, L.W.

2002-01-01

Over the last 30 years the US Environmental Protection Agency (EPA) has conducted field, laboratory, and scientific literature studies on a variety of technologically enhanced naturally occurring radioactive materials. In doing so, EPA has recognized that the physical and chemical characteristics of these wastes and products can vary significantly, and the Agency is conducting detailed evaluations of these radioactive materials on an industry-by-industry basis. An example of the Agency's current efforts to characterize and assess the risks of these materials from the uranium mining industry in a technical report is presented along with information on EPA's current field and laboratory studies. (author)

Life Cycle Assessment of Daugavgriva Waste Water Treatment Plant

OpenAIRE

Romagnoli, F; Fraga Sampaio, F; Blumberga, D

2009-01-01

This paper presents the assessment of the environmental impacts caused by the treatment of Riga’s waste water in the Daugavgriva plant with biogas energy cogeneration through the life cycle assessment (LCA). The LCA seems to be a good tool to assess and evaluate the most serious environmental impacts of a facility The results showed clearly that the impact category contributing the most to the total impact –eutrophicationcomes from the wastewater treatment stage. Cl...

Hazardous waste and environmental trade: China`s issues

Energy Technology Data Exchange (ETDEWEB)

Ma Jiang [National Research Center for Science and Technology for Development, Beijing (China)

1996-12-31

By presenting some case studies, this paper analyzes China`s situation with regard to hazardous waste: its environmental trade, treatment, and management. The paper describes China`s experiences with the environmental trade of hazardous waste in both the internal and international market. Regulations for managing the import of waste are discussed, as are China`s major approaches to the trading of hazardous waste both at home and overseas. The major reasons for setting up the Asian-Pacific Regional Training Center for Technology Transfer and Environmental Sound Management of Wastes in China and the activities involved in this effort are also described. 1 tab.

Optimal siting of solid waste-to-value-added facilities through a GIS-based assessment.

Science.gov (United States)

Khan, Md Mohib-Ul-Haque; Vaezi, Mahdi; Kumar, Amit

2018-01-01

Siting a solid waste conversion facility requires an assessment of solid waste availability as well as ensuring compliance with environmental, social, and economic factors. The main idea behind this study was to develop a methodology to locate suitable locations for waste conversion facilities considering waste availability as well as environmental and social constraints. A geographic information system (GIS) spatial analysis was used to identify the most suitable areas and to screen out unsuitable lands. The analytic hierarchy process (AHP) was used for a multi-criteria evaluation of relative preferences of different environmental and social factors. A case study was conducted for Alberta, a western province in Canada, by performing a province-wide waste availability assessment. The total available waste considered in this study was 4,077,514tonnes/year for 19 census divisions collected from 79 landfills. Finally, a location-allocation analysis was performed to determine suitable locations for 10 waste conversion facilities across the province. Copyright © 2017 Elsevier B.V. All rights reserved.

Environmental Assessment of Packaging: The Consumer Point of View

Science.gov (United States)

Van Dam YK

1996-09-01

When marketing environmentally responsible packaged products, the producer is confronted with consumer beliefs concerning the environmental friendliness of packaging materials. When making environmentally conscious packaging decisions, these consumer beliefs should be taken into account alongside the technical guidelines. Dutch consumer perceptions of the environmental friendliness of packaged products are reported and compared with the results of a life-cycle analysis assessment. It is shown that consumers judge environmental friendliness mainly from material and returnability. Furthermore, the consumer perception of the environmental friendliness of packaging material is based on the postconsumption waste, whereas the environmental effects of production are ignored. From the consumer beliefs concerning environmental friendliness implications are deduced for packaging policy and for environmental policy.KEY WORDS: Consumer behavior; Environment; Food; Packaging; Perception; Waste

High-level waste melter alternatives assessment report

Energy Technology Data Exchange (ETDEWEB)

Calmus, R.B.

1995-02-01

This document describes the Tank Waste Remediation System (TWRS) High-Level Waste (HLW) Program`s (hereafter referred to as HLW Program) Melter Candidate Assessment Activity performed in fiscal year (FY) 1994. The mission of the TWRS Program is to store, treat, and immobilize highly radioactive Hanford Site waste (current and future tank waste and encapsulated strontium and cesium isotopic sources) in an environmentally sound, safe, and cost-effective manner. The goal of the HLW Program is to immobilize the HLW fraction of pretreated tank waste into a vitrified product suitable for interim onsite storage and eventual offsite disposal at a geologic repository. Preparation of the encapsulated strontium and cesium isotopic sources for final disposal is also included in the HLW Program. As a result of trade studies performed in 1992 and 1993, processes planned for pretreatment of tank wastes were modified substantially because of increasing estimates of the quantity of high-level and transuranic tank waste remaining after pretreatment. This resulted in substantial increases in needed vitrification plant capacity compared to the capacity of original Hanford Waste Vitrification Plant (HWVP). The required capacity has not been finalized, but is expected to be four to eight times that of the HWVP design. The increased capacity requirements for the HLW vitrification plant`s melter prompted the assessment of candidate high-capacity HLW melter technologies to determine the most viable candidates and the required development and testing (D and T) focus required to select the Hanford Site HLW vitrification plant melter system. An assessment process was developed in early 1994. This document describes the assessment team, roles of team members, the phased assessment process and results, resulting recommendations, and the implementation strategy.

High-level waste melter alternatives assessment report

International Nuclear Information System (INIS)

Calmus, R.B.

1995-02-01

This document describes the Tank Waste Remediation System (TWRS) High-Level Waste (HLW) Program's (hereafter referred to as HLW Program) Melter Candidate Assessment Activity performed in fiscal year (FY) 1994. The mission of the TWRS Program is to store, treat, and immobilize highly radioactive Hanford Site waste (current and future tank waste and encapsulated strontium and cesium isotopic sources) in an environmentally sound, safe, and cost-effective manner. The goal of the HLW Program is to immobilize the HLW fraction of pretreated tank waste into a vitrified product suitable for interim onsite storage and eventual offsite disposal at a geologic repository. Preparation of the encapsulated strontium and cesium isotopic sources for final disposal is also included in the HLW Program. As a result of trade studies performed in 1992 and 1993, processes planned for pretreatment of tank wastes were modified substantially because of increasing estimates of the quantity of high-level and transuranic tank waste remaining after pretreatment. This resulted in substantial increases in needed vitrification plant capacity compared to the capacity of original Hanford Waste Vitrification Plant (HWVP). The required capacity has not been finalized, but is expected to be four to eight times that of the HWVP design. The increased capacity requirements for the HLW vitrification plant's melter prompted the assessment of candidate high-capacity HLW melter technologies to determine the most viable candidates and the required development and testing (D and T) focus required to select the Hanford Site HLW vitrification plant melter system. An assessment process was developed in early 1994. This document describes the assessment team, roles of team members, the phased assessment process and results, resulting recommendations, and the implementation strategy

Comparison of environmental performance for different waste management scenarios in East Africa: The case of Kampala City, Uganda

NARCIS (Netherlands)

Oyoo, R.; Leemans, R.; Mol, A.P.J.

2014-01-01

Poor waste flows management in East African cities has become an environmental and public health concerns to the city authorities and the general public. We assessed the environmental impacts of waste recycling in Kampala City, for four designed waste management scenarios, namely: (1) Scenario S1

Waste Isolation Pilot Plant Biennial Environmental Compliance Report

Energy Technology Data Exchange (ETDEWEB)

Westinghouse TRU Solutions

2000-12-01

This Biennial Environmental Compliance Report (BECR) documents environmental regulatory compliance at the Waste Isolation Pilot Plant (WIPP), a facility designed for the safe disposal of transuranic (TRU) radioactive waste, for the reporting period of April 1, 1998, to March 31, 2000. As required by the WIPP Land Withdrawal Act (LWA)(Public Law [Pub. L.] 102-579, and amended by Pub. L. 104-201), the BECR documents U.S. Department of Energy (DOE) Carlsbad Area Office's (hereinafter the ''CAO'') compliance with applicable environmental protection laws and regulations implemented by agencies of the federal government and the state of New Mexico. An issue was identified in the 1998 BECR relating to a potential cross-connection between the fire-water systems and the site domestic water system. While the CAO and its managing and operating contractor (hereinafter the ''MOC'') believe the site was always in compliance with cross-connection control requirements, hardware and procedural upgrades w ere implemented in March 1999 to strengthen its compliance posture. Further discussion of this issue is presented in section 30.2.2 herein. During this reporting period WIPP received two letters and a compliance order alleging violation of certain requirements outlined in section 9(a)(1) of the LWA. With the exception of one item, pending a final decision by the New Mexico Environment Department (NMED), all alleged violations have been resolved without the assessment of fines or penalties. Non-mixed TRU waste shipments began on March 26, 1999. Shipments continued through November 26, 1999, the effective date of the Waste Isolation Pilot Plant Hazardous Waste Facility Permit (NM4890139088-TSDF). No shipments regulated under the Hazardous Waste Facility Permit were received at WIPP during this BECR reporting period.

Waste Isolation Pilot Plant Biennial Environmental Compliance Report

International Nuclear Information System (INIS)

Westinghouse TRU Solutions

2000-01-01

This Biennial Environmental Compliance Report (BECR) documents environmental regulatory compliance at the Waste Isolation Pilot Plant (WIPP), a facility designed for the safe disposal of transuranic (TRU) radioactive waste, for the reporting period of April 1, 1998, to March 31, 2000. As required by the WIPP Land Withdrawal Act (LWA)(Public Law [Pub. L.] 102-579, and amended by Pub. L. 104-201), the BECR documents U.S. Department of Energy (DOE) Carlsbad Area Office's (hereinafter the ''CAO'') compliance with applicable environmental protection laws and regulations implemented by agencies of the federal government and the state of New Mexico. An issue was identified in the 1998 BECR relating to a potential cross-connection between the fire-water systems and the site domestic water system. While the CAO and its managing and operating contractor (hereinafter the ''MOC'') believe the site was always in compliance with cross-connection control requirements, hardware and procedural upgrades w ere implemented in March 1999 to strengthen its compliance posture. Further discussion of this issue is presented in section 30.2.2 herein. During this reporting period WIPP received two letters and a compliance order alleging violation of certain requirements outlined in section 9(a)(1) of the LWA. With the exception of one item, pending a final decision by the New Mexico Environment Department (NMED), all alleged violations have been resolved without the assessment of fines or penalties. Non-mixed TRU waste shipments began on March 26, 1999. Shipments continued through November 26, 1999, the effective date of the Waste Isolation Pilot Plant Hazardous Waste Facility Permit (NM4890139088-TSDF). No shipments regulated under the Hazardous Waste Facility Permit were received at WIPP during this BECR reporting period

Environmental assessment of the Carlsbad Environmental Monitoring and Research Center Facility

International Nuclear Information System (INIS)

1995-10-01

This Environmental Assessment has been prepared to determine if the Carlsbad Environmental Monitoring and Research Center (the Center), or its alternatives would have significant environmental impacts that must be analyzed in an Environmental Impact Statement. DOE's proposed action is to continue funding the Center. While DOE is not funding construction of the planned Center facility, operation of that facility is dependent upon continued funding. To implement the proposed action, the Center would initially construct a facility of approximately 2,300 square meters (25,000 square feet). The Phase 1 laboratory facilities and parking lot will occupy approximately 1.2 hectares (3 acres) of approximately 8.9 hectares (22 acres) of land which were donated to New Mexico State University (NMSU) for this purpose. The facility would contain laboratories to analyze chemical and radioactive materials typical of potential contaminants that could occur in the environment in the vicinity of the DOE Waste Isolation Pilot Plant (WIPP) site or other locations. The facility also would have bioassay facilities to measure radionuclide levels in the general population and in employees of the WIPP. Operation of the Center would meet the DOE requirement for independent monitoring and assessment of environmental impacts associated with the planned disposal of transuranic waste at the WIPP

Environmental assessment of the Carlsbad Environmental Monitoring and Research Center Facility

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-10-01

This Environmental Assessment has been prepared to determine if the Carlsbad Environmental Monitoring and Research Center (the Center), or its alternatives would have significant environmental impacts that must be analyzed in an Environmental Impact Statement. DOE`s proposed action is to continue funding the Center. While DOE is not funding construction of the planned Center facility, operation of that facility is dependent upon continued funding. To implement the proposed action, the Center would initially construct a facility of approximately 2,300 square meters (25,000 square feet). The Phase 1 laboratory facilities and parking lot will occupy approximately 1.2 hectares (3 acres) of approximately 8.9 hectares (22 acres) of land which were donated to New Mexico State University (NMSU) for this purpose. The facility would contain laboratories to analyze chemical and radioactive materials typical of potential contaminants that could occur in the environment in the vicinity of the DOE Waste Isolation Pilot Plant (WIPP) site or other locations. The facility also would have bioassay facilities to measure radionuclide levels in the general population and in employees of the WIPP. Operation of the Center would meet the DOE requirement for independent monitoring and assessment of environmental impacts associated with the planned disposal of transuranic waste at the WIPP.

Environmental Regulation of Offshore (E&P Waste Management in Nigeria: How Effective?

Directory of Open Access Journals (Sweden)

Anwuli Irene Ofuani

2011-09-01

Full Text Available The advancement of technology has led to the rapid development of the offshore oil and gas industry and a corresponding increase in the amount of wastes generated from the industry. These wastes must be properly managed so as to curtail their potential to negatively affect human health and the environment. As a result, environmental regulation of offshore oil and gas operations is becoming more stringent worldwide. The Environmental Guidelines and Standards for the Petroleum Industry in Nigeria (EGASPIN were issued to ensure that oil and gas industry operators do not degrade the environment in the course of their operations in Nigeria. Nonetheless, more attention has been focused on the economic aspects of offshore oil and gas industry rather than environmental aspects such as waste management. This article examines the legal aspects of offshore oil and gas waste management in Nigeria. It assesses the effectiveness of the mechanisms for the management of offshore E&P wastes in Nigeria as provided under EGASPIN in relation to other jurisdictions.

ENVIRONMENTAL RESEARCH BRIEF: WASTE MINIMIZATION FOR A MANUFACTURER OF COMPRESSED AIR EQUIPMENT COMPONENTS

Science.gov (United States)

The U.S. Environmental Protection Agency (EPA) has funded a pilot project to assist small- and medium-size manufacturers who want to minimize their generation of hazardous waste but lack the expertise to do so. Waste Minimization Assessment Centers (WMACs) were established at sel...

Environmental assessment, Richton Dome site, Mississippi

International Nuclear Information System (INIS)

1986-05-01

The Nuclear Waste Policy Act of 1982 (42 USC Sections 10101-10226) requires the environmental assessment of a potential site to include a statement of the basis for the nomination of a site as suitable for characterization. Volume 2 of this environmental assessment provides a detailed evaluation of the Richton Dome Site and its suitability as the site for a radioactive waste disposal facility under DOE siting guidelines, as well as a comparison of the Richton Dome site with other proposed sites. Evaluation of the Richton Dome site is based on the reference repository design, but the evaluation will not change if based on the Mission Plan repository concept. The comparative evaluation of proposed sites is required under DOE guidelines, but is not intended to directly support the subsequent recommendation of three sites for characterization as candidate sites. 428 refs., 24 figs., 62 tabs

Environmental Management Assessment of the Fernald Environmental Management Project (FEMP)

Energy Technology Data Exchange (ETDEWEB)

1993-04-01

This report documents the results of the Environmental Management Assessment performed at the Fernald Environmental Management Project (FEMP) in Fernald, Ohio. During this assessment, the activities conducted by the assessment team included review of internal documents and reports from previous audits and assessments; interviews with US Department of Energy (DOE) and FEMP contractor personnel; and inspection and observation of selected facilities and operations. The onsite portion of the assessment was conducted from March 15 through April 1, 1993, by DOE`s Office of Environmental Audit (EH-24) located within the Office of the Assistant Secretary for Environment, Safety, and Health (EH-1). EH-24 carries out independent assessments of DOE facilities and activities as part of the EH-1 Environment, Safety, and Health (ES&H) Oversight Audit Program. The EH-24 program is designed to evaluate the status of DOE facilities and activities with respect to compliance with Federal, state, and local environmental laws and regulations; compliance with DOE Orders, Guidance and Directives; conformance with accepted industry practices and standards of performance; and the status and adequacy of management systems developed to address environmental requirements. The Environmental Management Assessment of FEMP focused on the adequacy of environmental management systems. Further, in response to requests by the Office of Environmental Restoration and Waste Management (EM) and Fernald Field Office (FN), Quality Assurance and Environmental Radiation activities at FEMP were evaluated from a programmatic standpoint. The results of the evaluation of these areas are contained in the Environmental Protection Programs section in this report.

Environmental Management Assessment of the Fernald Environmental Management Project (FEMP)

International Nuclear Information System (INIS)

1993-04-01

This report documents the results of the Environmental Management Assessment performed at the Fernald Environmental Management Project (FEMP) in Fernald, Ohio. During this assessment, the activities conducted by the assessment team included review of internal documents and reports from previous audits and assessments; interviews with US Department of Energy (DOE) and FEMP contractor personnel; and inspection and observation of selected facilities and operations. The onsite portion of the assessment was conducted from March 15 through April 1, 1993, by DOE's Office of Environmental Audit (EH-24) located within the Office of the Assistant Secretary for Environment, Safety, and Health (EH-1). EH-24 carries out independent assessments of DOE facilities and activities as part of the EH-1 Environment, Safety, and Health (ES ampersand H) Oversight Audit Program. The EH-24 program is designed to evaluate the status of DOE facilities and activities with respect to compliance with Federal, state, and local environmental laws and regulations; compliance with DOE Orders, Guidance and Directives; conformance with accepted industry practices and standards of performance; and the status and adequacy of management systems developed to address environmental requirements. The Environmental Management Assessment of FEMP focused on the adequacy of environmental management systems. Further, in response to requests by the Office of Environmental Restoration and Waste Management (EM) and Fernald Field Office (FN), Quality Assurance and Environmental Radiation activities at FEMP were evaluated from a programmatic standpoint. The results of the evaluation of these areas are contained in the Environmental Protection Programs section in this report

Study of technical, environmental and economic assessment of the process of waste gasification by plasma torch of PlascoEnergy Group - Report

International Nuclear Information System (INIS)

Kunegel, Andre

2009-10-01

This study aims at assessing technical, environmental and economic performance of a technology developed by PlascoEnergy Group in its application to French household and similar wastes, at analysing PlascoEnergy project for their processing in a city of southern France, and at providing a global analysis of the appropriateness of plasma torch technologies to the gasification of these wastes, of other wastes to be defined, biomass and so on. After a presentation of the technology and a reference to a demonstrator project in Ottawa, the report presents the PlascoEnergy Company, the French installation and its differences with the demonstration project. Based on documents provided by PlascoEnergy, it reports an analysis of various critical points (waste preparation, gasification, waste introduction, waste movements in the oven, hot air recovery, gasification performance, syngas processing, engines, valorisation and removal of solid residues). Performance of the Ottawa plant are presented and commented. The use of the plasma torch technology in waste processing is described

Environmental assessment of waste matrices contaminated with arsenic.

Science.gov (United States)

Sanchez, F; Garrabrants, A C; Vandecasteele, C; Moszkowicz, P; Kosson, D S

2003-01-31

The use of equilibrium-based and mass transfer-based leaching tests has been proposed to provide an integrated assessment of leaching processes from solid wastes. The objectives of the research presented here are to (i) validate this assessment approach for contaminated soils and cement-based matrices, (ii) evaluate the use of diffusion and coupled dissolution-diffusion models for estimating constituent release, and (iii) evaluate model parameterization using results from batch equilibrium leaching tests and physical characterization. The test matrices consisted of (i) a soil contaminated with arsenic from a pesticide production facility, (ii) the same soil subsequently treated by a Portland cement stabilization/solidification (S/S) process, and (iii) a synthetic cement-based matrix spiked with arsenic(III) oxide. Results indicated that a good assessment of contaminant release from contaminated soils and cement-based S/S treated wastes can be obtained by the integrated use of equilibrium-based and mass transfer-based leaching tests in conjunction with the appropriate release model. During the time scale of laboratory testing, the release of arsenic from the contaminated soil matrix was governed by diffusion and the solubility of arsenic in the pore solution while the release of arsenic from the cement-based matrices was mainly controlled by solubilization at the interface between the matrix and the bulk leaching solution. In addition, results indicated that (i) estimation of the activity coefficient within the matrix pore water is necessary for accurate prediction of constituent release rates and (ii) inaccurate representation of the factors controlling release during laboratory testing can result in significant errors in release estimates.

Environmental Restoration Disposal Facility waste acceptance criteria. Revision 1

International Nuclear Information System (INIS)

Corriveau, C.E.

1996-01-01

The Environmental Restoration Disposal Facility (ERDF) is designed to be an isolation structure for low-level radioactive remediation waste, chemically contaminated remediation waste, and remediation waste that contains both chemical and radioactive constituents (i.e., mixed remediation waste) produced during environmental remediation of Comprehensive Environmental Response, Compensation, and Liability Act of 1980 (CERCLA) past-practice units at the Hanford Site. Remedial action wastes, which will become a structural component of the ERDF, include bulk soil, demolition debris, and miscellaneous wastes from burial grounds. These wastes may originate from CERCLA past-practice sites (i.e., operable units) in the 100 Areas, the 200 Areas, and the 300 Area of the Hanford Site

Life cycle modelling of environmental impacts from application of processed organic municipal solid waste on agricultural land (EASEWASTE)

DEFF Research Database (Denmark)

Hansen, Trine Lund; Bhander, Gurbakhash Singh; Christensen, Thomas Højlund

2006-01-01

and use of commercial fertilizers. The model is part of a larger model, Environmental Assessment of Solid Waste Systems and Technology (EASEWASTE), developed as a decisionsupport model, focusing on assessment of alternative waste management options. The environmental impacts of the land application......A model capable of quantifying the potential environmental impacts of agricultural application of composted or anaerobically digested source-separated organic municipal solid waste (MSW) is presented. In addition to the direct impacts, the model accounts for savings by avoiding the production...... of processed organic waste are quantified by emission coefficients referring to the composition of the processed waste and related to specific crop rotation as well as soil type. The model contains several default parameters based on literature data, field experiments and modelling by the agro-ecosystem model...

Environmental impacts and benefits of state-of-the-art technologies for E-waste management.

Science.gov (United States)

Ikhlayel, Mahdi

2017-10-01

This study aims to evaluate the environmental impacts and benefits of state-of-the-art technologies for proper e-waste handling using Jordan as a case study. Life Cycle Assessment (LCA) was employed to evaluate five advanced management systems represent state-of-the-art treatment technologies, including sanitary landfilling; proper recycling of metals, materials, and precious metals (PMs); and incineration of plastic and the hazardous portion of printed circuit boards (PCBs). Six e-waste products that contribute the most to the e-waste in Jordan were included in the assessment of each scenario, which resulted in 30 total cases of e-waste management. The findings indicated that landfills for the entire components of the e-waste stream are the worst option and should be avoided. The most promising e-waste management scenario features integrated e-waste processes based on the concept of Integrated Waste Management (IWM), including recycling materials such as non-PMs and PMs, incinerating plastic and the hazardous content of PCBs using the energy recovered from incineration, and using sanitary landfills of residues. For this scenario, the best environmental performance was obtained for the treatment of mobile phones. Incineration of the portion of hazardous waste using energy recovery is an option that deserves attention. Because scenario implementation depends on more than just the environmental benefits (e.g., economic cost and technical aspects), the study proposes a systematic approach founded on the IWM concept for e-waste management scenario selection. Copyright © 2017 Elsevier Ltd. All rights reserved.

A Critical Evaluation of Waste Incineration Plants in Wuhan (China) Based on Site Selection, Environmental Influence, Public Health and Public Participation.

Science.gov (United States)

Hu, Hui; Li, Xiang; Nguyen, Anh Dung; Kavan, Philip

2015-07-08

With the rapid development of the waste incineration industry in China, top priority has been given to the problem of pollution caused by waste incineration. This study is the first attempt to assess all the waste incineration plants in Wuhan, the only national key city in central China, in terms of environmental impact, site selection, public health and public participation. By using a multi-criterion assessment model for economic, social, public health and environmental effects, this study indicates these incineration plants are established without much consideration of the local residents' health and environment. A location analysis is also applied and some influences of waste incineration plants are illustrated. This study further introduces a signaling game model to prove that public participation is a necessary condition for improving the environmental impact assessment and increasing total welfare of different interest groups in China. This study finally offers some corresponding recommendations for improving the environmental impact assessments of waste incineration projects.

A Critical Evaluation of Waste Incineration Plants in Wuhan (China Based on Site Selection, Environmental Influence, Public Health and Public Participation

Directory of Open Access Journals (Sweden)

Hui Hu

2015-07-01

Full Text Available With the rapid development of the waste incineration industry in China, top priority has been given to the problem of pollution caused by waste incineration. This study is the first attempt to assess all the waste incineration plants in Wuhan, the only national key city in central China, in terms of environmental impact, site selection, public health and public participation. By using a multi-criterion assessment model for economic, social, public health and environmental effects, this study indicates these incineration plants are established without much consideration of the local residents’ health and environment. A location analysis is also applied and some influences of waste incineration plants are illustrated. This study further introduces a signaling game model to prove that public participation is a necessary condition for improving the environmental impact assessment and increasing total welfare of different interest groups in China. This study finally offers some corresponding recommendations for improving the environmental impact assessments of waste incineration projects.

Waste electrical and electronic Equipment (E-Wastes) management in Ghana: environmental impacts at Agbogbloshie, Accra Ghana

International Nuclear Information System (INIS)

Manukure, Sampson Atiemo

2016-07-01

Ghana has relatively large volumes of e-wastes but inefficient recycling methods adopted by the informal sector causes both environmental contamination and potential loss of scarce metals. The control of pollution and management of e-wastes are twin challenges confronted by Ghana. The main objective of the study is to assess the extent to which the current methods employed in e-waste management in Ghana promote sound environmental management. Interviews and field observations were used to collect and collate data from key stakeholders on sustainable e-wastes management in Ghana. Soil samples were collected and analysed using Energy Dispersive X-ray fluorescence technique (EDXRF) and neutron activation analysis (NAA). The results of the field survey revealed that there were three main method of getting e-waste into the yard; house-to-house collection, business-to-business collection and e-waste from dump sites. Majority of the scrap dealers (72%) have not received any form of training in the handling of the hazardous fractions hence do not use any personal protection equipment (PPE). There is poor awareness on the association between disease symptoms and e-waste activity however, 46% of the workers associated symptoms such as headaches, fever, stomach ache and vomiting to e-wastes activities. The challenges of the scrap dealers identified include; rampant arrests and beatings of collectors, fluctuating prices of general scraps, transportation costs, lack of access to working capital as well as ethnic, political and religious difference among the scrap dealers. The results of the elemental analysis revealed that generally the different sampling locations in the study area exhibited an overall metallic dominance pattern of SC > RD > VG > MS > CS > RS > DS > SG > BS. Lead levels registered in the in the soil samples analyzed ranged from 14.2 mg/kg to 7,020.0 mg/kg while Cd was found to be in the range of DS>SG>RS>MS>RD>CS>VF>SC. All the sampling sites showed very high

Waste Isolation Pilot Plant disposal phase: Draft supplemental Environmental Impact Statement

International Nuclear Information System (INIS)

1996-11-01

Purpose of this SEIS-II is to provide information on environmental impacts regarding DOE's proposed disposal operations at WIPP. To that end, SEIS-II was prepared to assess the potential impacts of continuing the phased development of WIPP as a geologic repository for the safe disposal of transuranic (TRU) waste. SEIS-II evaluates a Proposed Action, three Action Alternatives, and two No Action Alternatives. The Proposed Action describes the treatment and disposal of the Basic Inventory of TRU waste over a 35-year period. SEIS-II evaluates environmental impacts resulting from the various treatment options; transportation of TRU waste to WIPP using truck, a combination of truck and regular rail service, and a combination of truck and dedicated rail service; and the disposal of this waste in the repository. Evaluated impacts include those to the general environment and to human health. Additional issues associated with implementation of the alternatives are discussed

Assessment of Environmental Factors of Geology on Waste and Engineering Barriers for Waste Storage Near Surface

International Nuclear Information System (INIS)

Arimuladi SP

2007-01-01

Geological environment factors include features and processes occurring within that spatial and temporal (post-closure) domain whose principal effect is to determine the evolution of the physical, chemical, biological and human conditions of the domain that are relevant to estimating the release and migration of radionuclide and consequent exposure to man. Hardness of radioactive waste and engineer barrier can be decrease by environmental factors. Disposal system domain geological environment factors is a category in the International FEP list and is divided into sub-categories. There are 13 sub-factors of geological environment, 12 sub-factors influence hardness of radioactive waste and engineer barrier, thermal processes and conditions in geosphere can be excluded. (author)

Waste Isolation Pilot Plant 1999 Site Environmental Report

Energy Technology Data Exchange (ETDEWEB)

Evans, Roy B.; Adams, Amy; Martin, Don; Morris, Randall C.; Reynolds, Timothy D.; Warren, Ronald W.

2000-09-30

The U.S. Department of Energy's (DOE)Carlsbad Area Office and the Westinghouse Waste Isolation Division (WID) are dedicated to maintaining high quality management of Waste Isolation Pilot Plant (WIPP) environmental resources. DOE Order 5400.1, General Environmental Protection Program, and DOE Order 231.1, Environmental, Safety, and Health Reporting, require that the environment at and near DOE facilities be monitored to ensure the safety and health of the public and the environment. This Waste Isolation Pilot Plant 1999 Site Environmental Report summarizes environmental data from calendar year 1999 that characterize environmental management performance and demonstrate compliance with federal and state regulations. This report was prepared in accordance with DOE Order 5400.1, DOE Order 231.1, the Environmental Regulatory Guide for Radiological Effluent Monitoring and Environmental Surveillance (DOE/EH- 0173T), and the Waste Isolation Pilot Plant Environmental Protection Implementation Plan (DOE/WIPP 96-2199). The above orders and guidance documents require that DOE facilities submit an Annual Site Environmental Report to DOE Headquarters, Office of the Assistant Secretary for Environment, Safety, and Health. The purpose of this report is to provide a comprehensive description of operational environmental monitoring activities, to provide an abstract of environmental activities conducted to characterize site environmental management performance to confirm compliance with environmental standards and requirements, and to highlight significant programs and efforts of environmental merit at WIPP during calendar year 1999. WIPP received its first shipment of waste on March 26, 1999. In 1999, no evidence was found of any adverse effects from WIPP on the surrounding environment. Radionuclide concentrations in the environment surrounding WIPP were not statistically higher in 1999 than in 1998.

INCORPORATING ENVIRONMENTAL AND ECONOMIC CONSIDERATIONS INTO PROCESS DESIGN: THE WASTE REDUCTION (WAR) ALGORITHM

Science.gov (United States)

A general theory known as the WAste Reduction (WASR) algorithm has been developed to describe the flow and the generation of potential environmental impact through a chemical process. This theory integrates environmental impact assessment into chemical process design Potential en...

Environmental issues of repository licensing: an evaluation of a hypothetical high-level radioactive waste repository

International Nuclear Information System (INIS)

Owen, J.L.; McGinnis, J.T.; Harper, C.M.; Battelle Columbus Labs., OH)

1982-01-01

This paper presents results of an environmental assessment conducted under the direction of the Office of Nuclear Waste Isolation as part of the National Waste Terminal Storage program. The study defined a range of potential environmental effects of constructing, operating, decommissioning, and long-term isolation of a nuclear waste repository. The analytical methodology used to determine potential environmental effects required definition of a hypothetical environmental setting and repository. Potentially applicable regulatory requirements were identified and were used as guidelines to evaluate permitting feasibility. The environmental effects of repository development were analyzed for the two major time periods of concern: short term (the period of construction, operation, and decommissioning) and long term (the isolation period after decommissioning). As a result of this analysis, major environmental uncertainties and issues were identified. 11 references, 5 figures

Assessment of solid waste management systems in Ibadan North ...

African Journals Online (AJOL)

Assessment of solid waste management systems in Ibadan North, Oyo State using geo-spatial ... Ethiopian Journal of Environmental Studies and Management ... Keywords: GIS, Median, Nearest Neighbour Analysis (NNA), Skip Bins ...

Determining ''Best Practicable Environmental Options'' for final waste disposal of radioactive waste

International Nuclear Information System (INIS)

Smith, Graham

1999-01-01

This presentation discusses some ideas on what the Best Practical Environmental Option (BPEO) process should include. A BPEO study to help develop a radioactive waste management strategy should not only look at post-closure safety of a facility. In the UK there was a 1986 Study of BPEOs for management of low and intermediate level radioactive wastes. This study tried to answer important questions such as (1) What are the practical options, (2) Which wastes should go to shallow burial, (3) Which wastes should go to sea disposal, (4) How does storage compare with disposal and (5) What are the cost and environmental trade-offs. The presentation discusses what was done to answer the questions. The BPEO Study resulted in major improved effort to characterise waste, much greater quantitative understanding of where and when the real costs, and environmental and radiological impacts arise. All options would be useful within a national strategy. But there was clearly a need for resolution of political acceptance problems, integration of policy with other hazardous waste management, and stronger legal framework

Life-cycle assessment of a Waste-to-Energy plant in central Norway: Current situation and effects of changes in waste fraction composition.

Science.gov (United States)

Lausselet, Carine; Cherubini, Francesco; Del Alamo Serrano, Gonzalo; Becidan, Michael; Strømman, Anders Hammer

2016-12-01

Waste-to-Energy (WtE) plants constitute one of the most common waste management options to deal with municipal solid waste. WtE plants have the dual objective to reduce the amount of waste sent to landfills and simultaneously to produce useful energy (heat and/or power). Energy from WtE is gaining steadily increasing importance in the energy mix of several countries. Norway is no exception, as energy recovered from waste currently represents the main energy source of the Norwegian district heating system. Life-cycle assessments (LCA) of WtE systems in a Norwegian context are quasi-nonexistent, and this study assesses the environmental performance of a WtE plant located in central Norway by combining detailed LCA methodology with primary data from plant operations. Mass transfer coefficients and leaching coefficients are used to trace emissions over the various life-cycle stages from waste logistics to final disposal of the ashes. We consider different fractions of input waste (current waste mix, insertion of 10% car fluff, 5% clinical waste and 10% and 50% wood waste), and find a total contribution to Climate Change Impact Potential ranging from 265 to 637gCO 2 eq/kg of waste and 25 to 61gCO 2 eq/MJ of heat. The key drivers of the environmental performances of the WtE system being assessed are the carbon biogenic fraction and the lower heating value of the incoming waste, the direct emissions at the WtE plant, the leaching of the heavy metals at the landfill sites and to a lesser extent the use of consumables. We benchmark the environmental performances of our WtE systems against those of fossil energy systems, and we find better performance for the majority of environmental impact categories, including Climate Change Impact Potential, although some trade-offs exist (e.g. higher impacts on Human Toxicity Potential than natural gas, but lower than coal). Also, the insertion of challenging new waste fractions is demonstrated to be an option both to cope with the

Risk assessment and optimization (ALARA) analysis for the environmental remediation of Brookhaven National Laboratory's hazardous waste management facility

International Nuclear Information System (INIS)

Dionne, B.J.; Morris, S. III; Baum, J.W.

1998-03-01

The Department of Energy's (DOE) Office of Environment, Safety, and Health (EH) sought examples of risk-based approaches to environmental restoration to include in their guidance for DOE nuclear facilities. Extensive measurements of radiological contamination in soil and ground water have been made at Brookhaven National Laboratory's Hazardous Waste Management Facility (HWMF) as part of a Comprehensive Environmental Response, Compensation and Liability Act (CERCLA) remediation process. This provided an ideal opportunity for a case study. This report provides a risk assessment and an open-quotes As Low as Reasonably Achievableclose quotes (ALARA) analysis for use at other DOE nuclear facilities as an example of a risk-based decision technique

Final waste management programmatic environmental impact statement for managing treatment, storage, and disposal of radioactive and hazardous waste. Volume IV of V

International Nuclear Information System (INIS)

1997-01-01

The Final Waste Management Programmatic Environmental Impact Statement (WM PEIS) examines the potential environmental and cost impacts of strategic management alternatives for managing five types of radioactive and hazardous wastes that have resulted and will continue to result from nuclear defense and research activities at a variety of sites around the United States. The five waste types are low-level mixed waste, low-level waste, transuranic waste, high-level waste, and hazardous waste. The WM PEIS provides information on the impacts of various siting alternatives which the Department of Energy (DOE) will use to decide at which sites to locate additional treatment, storage, and disposal capacity for each waste type.Transportation is an integral component of the alternatives being considered for each type of radioactive waste in the U.S. Department of Energy (DOE) Waste Management Programmatic Environmental Impact Statement (WM PEIS). The types of radioactive waste considered in Part I are high-level waste (HLW), low-level waste (LLW), transuranic waste (TRUW), and low-level mixed waste (LLMW). For some alternatives, radioactive waste would be shipped among the DOE sites at various stages of the treatment, storage, and disposal (TSD) process. The magnitude of the transportation-related activities varies with each alternative, ranging from minimal transportation for decentralized approaches to significant transportation for some centralized approaches. The human health risks associated with transporting various waste materials were assessed to ensure a complete appraisal of the impacts of each PEIS alternative being considered

Projection of Environmental Pollutant Emissions From Different Final Waste Disposal Methods Based on Life Cycle Assessment Studies in Qazvin City

Directory of Open Access Journals (Sweden)

Javad Torkashvand

2015-12-01

Full Text Available In the current study, the life cycle assessment (LCA method was used to expect the emissions of different environmental pollutants through qualitative and quantitative analyses of solid wastes of Qazvin city in different final disposal methods. Therefore, four scenarios with the following properties considering physical analysis of Qazvin’s solid wastes, the current status of solid waste management in Iran, as well as the future of solid waste management of Qazvin were described. In order to detect the quantity of the solid wastes, the volume-weighted analysis was used and random sampling method was used for physical analysis. Of course, regarding the method of LCA, it contains all stages from solid wastes generation to its disposal. However, since the main aim of this study was final disposal stage, the emissions of pollutants of these stages were ignored. Next, considering the mixture of the solid waste, the amount of pollution stemming from each of final disposal methods from other cities having similar conditions was estimated. The findings of the study showed that weight combination of Qazvin solid wastes is entirely similar to that of other cities. Thus, the results of this study can be applied by decision makers around the country. In scenarios 1 and 2, emission of leachate containing high amounts of COD and BOD is high and also the highest content of nitrate, which can contaminate water and soil resulting in high costs for their management. In scenarios 3 and 4, the amounts of gaseous pollutants, particularly CO2, as well as nitrogen oxides are very high. In conclusion, the LCA methods can effectively contribute to the management of municipal solid wastes (MSW to control environmental pollutants with least expenses.

WASTE MINIMIZATION ASSESSMENT FOR A MANUFACTURER OF CUSTOM MOLDED PLASTIC PRODUCTS

Science.gov (United States)

The U.S. Environmental Protection Agency (EPA) has funded a pilot project to assist small- and medium-size manufacturers who want to minimize their generation of waste but who lack the expertise to do so. Waste Minimization Assessment Centers (WMACs) were established at selected ...

Low-level waste inventory, characteristics, generation, and facility assessment for treatment, storage, and disposal alternatives considered in the US Department of Energy waste management programmatic environmental impact statement

Energy Technology Data Exchange (ETDEWEB)

Goyette, M.L.; Dolak, D.A.

1996-12-01

This report provides technical support information for use in analyzing environmental impacts associated with U.S. Department of Energy (DOE) low-level radioactive waste (LLW) management alternatives in the Waste-Management (WM) Programmatic Environmental Impact Statement (PEIS). Waste loads treated and disposed of for each of the LLW alternatives considered in the DOE WM PEIS are presented. Waste loads are presented for DOE Waste Management (WM) wastes, which are generated from routine operations. Radioactivity concentrations and waste quantities for treatment and disposal under the different LLW alternatives are described for WM waste. 76 refs., 14 figs., 42 tabs.

ENVIRONMENTALLY SOUND DISPOSAL OF RADIOACTIVE MATERIALS AT A RCRA HAZARDOUS WASTE DISPOSAL FACILITY

International Nuclear Information System (INIS)

Romano, Stephen; Welling, Steven; Bell, Simon

2003-01-01

The use of hazardous waste disposal facilities permitted under the Resource Conservation and Recovery Act (''RCRA'') to dispose of low concentration and exempt radioactive materials is a cost-effective option for government and industry waste generators. The hazardous and PCB waste disposal facility operated by US Ecology Idaho, Inc. near Grand View, Idaho provides environmentally sound disposal services to both government and private industry waste generators. The Idaho facility is a major recipient of U.S. Army Corps of Engineers FUSRAP program waste and received permit approval to receive an expanded range of radioactive materials in 2001. The site has disposed of more than 300,000 tons of radioactive materials from the federal government during the past five years. This paper presents the capabilities of the Grand View, Idaho hazardous waste facility to accept radioactive materials, site-specific acceptance criteria and performance assessment, radiological safety and environmental monitoring program information

Radioactive Waste Management Complex low-level waste radiological performance assessment

Energy Technology Data Exchange (ETDEWEB)

Maheras, S.J.; Rood, A.S.; Magnuson, S.O.; Sussman, M.E.; Bhatt, R.N.

1994-04-01

This report documents the projected radiological dose impacts associated with the disposal of radioactive low-level waste at the Radioactive Waste Management Complex at the Idaho National Engineering Laboratory. This radiological performance assessment was conducted to evaluate compliance with applicable radiological criteria of the US Department of Energy and the US Environmental Protection Agency for protection of the public and the environment. The calculations involved modeling the transport of radionuclides from buried waste, to surface soil and subsurface media, and eventually to members of the public via air, groundwater, and food chain pathways. Projections of doses were made for both offsite receptors and individuals inadvertently intruding onto the site after closure. In addition, uncertainty and sensitivity analyses were performed. The results of the analyses indicate compliance with established radiological criteria and provide reasonable assurance that public health and safety will be protected.

Radioactive Waste Management Complex low-level waste radiological performance assessment

International Nuclear Information System (INIS)

Maheras, S.J.; Rood, A.S.; Magnuson, S.O.; Sussman, M.E.; Bhatt, R.N.

1994-04-01

This report documents the projected radiological dose impacts associated with the disposal of radioactive low-level waste at the Radioactive Waste Management Complex at the Idaho National Engineering Laboratory. This radiological performance assessment was conducted to evaluate compliance with applicable radiological criteria of the US Department of Energy and the US Environmental Protection Agency for protection of the public and the environment. The calculations involved modeling the transport of radionuclides from buried waste, to surface soil and subsurface media, and eventually to members of the public via air, groundwater, and food chain pathways. Projections of doses were made for both offsite receptors and individuals inadvertently intruding onto the site after closure. In addition, uncertainty and sensitivity analyses were performed. The results of the analyses indicate compliance with established radiological criteria and provide reasonable assurance that public health and safety will be protected

Radiological dose assessment of Department of Energy Pinellas Plant waste proposed for disposal at Laidlaw Environmental Services of South Carolina, Inc

International Nuclear Information System (INIS)

Socolof, M.L.; Lee, D.W.

1996-05-01

The U.S. Department of Energy (DOE) Pinellas Plant in Largo, FL is proposing to ship and dispose of hazardous sludge, listed as F006 waste, to the Laidlaw Environmental Services of South Carolina, Inc. (Laidlaw) treatment, storage, and disposal facility in Pinewood, South Carolina. This sludge contains radioactive tritium in concentrations of about 28 pCi/g. The objective of this study is to assess the possible radiological impact to workers at the Laidlaw facility and members of the public due to the handling, processing, and burial of the DOE waste containing tritium

Radiological dose assessment of Department of Energy Pinellas Plant waste proposed for disposal at Laidlaw Environmental Services of South Carolina, Inc.

Energy Technology Data Exchange (ETDEWEB)

Socolof, M.L.; Lee, D.W.

1996-05-01

The U.S. Department of Energy (DOE) Pinellas Plant in Largo, FL is proposing to ship and dispose of hazardous sludge, listed as F006 waste, to the Laidlaw Environmental Services of South Carolina, Inc. (Laidlaw) treatment, storage, and disposal facility in Pinewood, South Carolina. This sludge contains radioactive tritium in concentrations of about 28 pCi/g. The objective of this study is to assess the possible radiological impact to workers at the Laidlaw facility and members of the public due to the handling, processing, and burial of the DOE waste containing tritium.

Contribution to draft generic environmental impact statement on commercial waste management: radioactive waste isolation in geologic formations

International Nuclear Information System (INIS)

1978-04-01

This document concentrates on deep geologic isolation of wastes in bedded salt, granite, shale, and basalt with emphasis on wastes from three fuel cycles: reprocessing wastes from uranium and plutonium recycling, reprocessing wastes from uranium-only recycling, and spent unreprocessed fuel with no recycling. The analyses presented in this document are based on preconceptual repository designs. As the repository designs progress through future phases, refinements will occur which might modify some of these results. The 12 sections in the report are: introduction; selection and description of generic repository sites; LWR wastes to be isolated in geologic formations; description of waste isolation facilities; effluents from the waste isolation facility; assessment of environment impacts for various geographical locations of a waste isolation facility; environmental monitoring; decommissioning; mine decommissioning site restoration; deep geologic alternative actions; potential mechanisms of containment failure; and considerations relevant to provisional versus final storage

Probe into Environmental Kuznets Characteristics and Causes of Wastewater,Waste Gas, and Solid Wastes in Wuhan City

Institute of Scientific and Technical Information of China (English)

刘耀彬; 李仁东

2004-01-01

Environmental Kuznets characteristics and causes of waste water, waste gas, and solid wastes in Wuhan city was researched; By comparing the variation of "three wastes", i.e. waste water, waste gas, and solid wastes, the model between standardized per capita GDP and values of "three wastes" discharge was established and the causes were analyzed based on the theory of environmental economics. The results show that 1) the total amount is fluctuantly increasing, but the discharges of the three kinds are temporarily different, 2) the curve conforms to the three-power function, in which the curve descends from 1985 to 1994, and the curve preliminary shows the environmental Kuznets characteristics from 1995 to 2001, 3) the simulated calculation illustrates that the turning point of this environmental Kuznets curve would be over 25007.25 Yuan per caprta, and 4) the economic development, changing of industry structure, energy resource structure, and environmental policies are the main factors leading to the Environmental Kuznets Curve in Wuhan city.

Environmental impact assessment in the Nordic Countries; Miljoekonsekvensbeskrivningar i Norden

Energy Technology Data Exchange (ETDEWEB)

Broden, K. [Studsvik RadWaste AB (Sweden); Palsson, S.E. [Geislavarnir rikisins (Iceland); Poroddsson, P. [Skipulagsstofnun (Iceland)

2000-12-01

A meeting on Environmental Impact Assessment has been held in Iceland, September 2-6, 2000. It was held within the framework of the project NKS/SOS-3 (Radioactive waste), subproject NKS/SOS-3.1 (Environmental Impact Assessment). The meeting included presentations, discussions and a study trip to the Egilsstadir and Myvatn districts. (au)

Federal environmental assessment panel process

International Nuclear Information System (INIS)

Edwards, R.A.; King, J.M.

1996-01-01

The Government of Canada inaugurated an environmental assessment process in 1973. Since that time, the Department of Natural Resources, or its predecessor, the Department of Energy Mines and Resources, and industrial clients of the Department, have been major participants in the process. In 1995, the authors interviewed representatives of a number of client industries and selected individuals, to ask their opinion of the public hearing part of the environmental assessment process, with the objective of identifying shortcomings and proposing improvements. Respondents criticized the hearings as costly, time-wasting, bureaucratic, and uncertain in cost, time, and outcome. A number of observations on noted areas of shortcoming are presented in this paper, with suggestions for improvement

Federal environmental assessment panel process

Energy Technology Data Exchange (ETDEWEB)

Edwards, R A; King, J M [Natural Resources Canada, Ottawa, ON (Canada)

1997-12-31

The Government of Canada inaugurated an environmental assessment process in 1973. Since that time, the Department of Natural Resources, or its predecessor, the Department of Energy Mines and Resources, and industrial clients of the Department, have been major participants in the process. In 1995, the authors interviewed representatives of a number of client industries and selected individuals, to ask their opinion of the public hearing part of the environmental assessment process, with the objective of identifying shortcomings and proposing improvements. Respondents criticized the hearings as costly, time-wasting, bureaucratic, and uncertain in cost, time, and outcome. A number of observations on noted areas of shortcoming are presented in this paper, with suggestions for improvement.

Modelling of environmental impacts of solid waste landfilling within the life-cycle analysis program EASEWASTE.

Science.gov (United States)

Kirkeby, Janus T; Birgisdottir, Harpa; Bhander, Gurbakash Singh; Hauschild, Michael; Christensen, Thomas H

2007-01-01

A new computer-based life-cycle assessment model (EASEWASTE) has been developed to evaluate resource and environmental consequences of solid waste management systems. This paper describes the landfilling sub-model used in the life-cycle assessment program EASEWASTE, and examines some of the implications of this sub-model. All quantities and concentrations of leachate and landfill gas can be modified by the user in order to bring them in agreement with the actual landfill that is assessed by the model. All emissions, except the generation of landfill gas, are process specific. The landfill gas generation is calculated on the basis of organic matter in the landfilled waste. A landfill assessment example is provided. For this example, the normalised environmental effects of landfill gas on global warming and photochemical smog are much greater than the environmental effects for landfill leachate or for landfill construction. A sensitivity analysis for this example indicates that the overall environmental impact is sensitive to the gas collection efficiency and the use of the gas, but not to the amount of leachate generated, or the amount of soil or liner material used in construction. The landfill model can be used for evaluating different technologies with different liners, gas and leachate collection efficiencies, and to compare the environmental consequences of landfilling with alternative waste treatment options such as incineration or anaerobic digestion.

Modelling of environmental impacts of solid waste landfilling within the life-cycle analysis program EASEWASTE

International Nuclear Information System (INIS)

Kirkeby, Janus T.; Birgisdottir, Harpa; Bhander, Gurbakash Singh; Hauschild, Michael; Christensen, Thomas H.

2007-01-01

A new computer-based life-cycle assessment model (EASEWASTE) has been developed to evaluate resource and environmental consequences of solid waste management systems. This paper describes the landfilling sub-model used in the life-cycle assessment program EASEWASTE, and examines some of the implications of this sub-model. All quantities and concentrations of leachate and landfill gas can be modified by the user in order to bring them in agreement with the actual landfill that is assessed by the model. All emissions, except the generation of landfill gas, are process specific. The landfill gas generation is calculated on the basis of organic matter in the landfilled waste. A landfill assessment example is provided. For this example, the normalised environmental effects of landfill gas on global warming and photochemical smog are much greater than the environmental effects for landfill leachate or for landfill construction. A sensitivity analysis for this example indicates that the overall environmental impact is sensitive to the gas collection efficiency and the use of the gas, but not to the amount of leachate generated, or the amount of soil or liner material used in construction. The landfill model can be used for evaluating different technologies with different liners, gas and leachate collection efficiencies, and to compare the environmental consequences of landfilling with alternative waste treatment options such as incineration or anaerobic digestion

Environmental Assessment for the Closure of the High-Level Waste Tanks in F- & H-Areas at the Savannah River Site

Energy Technology Data Exchange (ETDEWEB)

N/A

1996-07-31

This Environmental Assessment (EA) has been prepared by the Department of Energy (DOE) to assess the potential environmental impacts associated with the closure of 51 high-level radioactive waste tanks and tank farm ancillary equipment (including transfer lines, evaporators, filters, pumps, etc) at the Savannah River Site (SRS) located near Aiken, South Carolina. The waste tanks are located in the F- and H-Areas of SRS and vary in capacity from 2,839,059 liters (750,000 gallons) to 4,921,035 liters (1,300,000 gallons). These in-ground tanks are surrounded by soil to provide shielding. The F- and H-Area High-Level Waste Tanks are operated under the authority of Industrial Wastewater Permits No.17,424-IW; No.14520, and No.14338 issued by the South Carolina Department of Health and Environmental Control (SCDHEC). In accordance with the Permit requirements, DOE has prepared a Closure Plan (DOE, 1996) and submitted it to SCDHEC for approval. The Closure Plan identifies all applicable or relevant and appropriate regulations, statutes, and DOE Orders for closing systems operated under the Industrial Wastewater Permits. When approved by SCDHEC, the Closure Plan will present the regulatory process for closing all of the F- and H-Area High Level Waste Tanks. The Closure Plan establishes performance objectives or criteria to be met prior to closing any tank, group of tanks, or ancillary tank farm equipment. The proposed action is to remove the residual wastes from the tanks and to fill the tanks with a material to prevent future collapse and bind up residual waste, to lower human health risks, and to increase safety in and around the tanks. If required, an engineered cap consisting of clay, backfill (soil), and vegetation as the final layer to prevent erosion would be applied over the tanks. The selection of tank system closure method will be evaluated against the following Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA) criteria described in 40

Environmental impacts of food waste: Learnings and challenges from a case study on UK

DEFF Research Database (Denmark)

Tonini, Davide; Albizzati, Paola Federica; Astrup, Thomas Fruergaard

2018-01-01

by four sectors of the food supply chain in United Kingdom, namely processing, wholesale and retail, food service, and households. The impacts were quantified for ten environmental impact categories, from Global Warming to Water Depletion, including indirect land use change impacts due to demand for land......Food waste, particularly when avoidable, incurs loss of resources and considerable environmental impacts due to the multiple processes involved in the life cycle. This study applies a bottom-up life cycle assessment method to quantify the environmental impacts of the avoidable food waste generated...

Environmental impacts of food waste: Learnings and challenges from a case study on UK.

Science.gov (United States)

Tonini, Davide; Albizzati, Paola Federica; Astrup, Thomas Fruergaard

2018-06-01

Food waste, particularly when avoidable, incurs loss of resources and considerable environmental impacts due to the multiple processes involved in the life cycle. This study applies a bottom-up life cycle assessment method to quantify the environmental impacts of the avoidable food waste generated by four sectors of the food supply chain in United Kingdom, namely processing, wholesale and retail, food service, and households. The impacts were quantified for ten environmental impact categories, from Global Warming to Water Depletion, including indirect land use change impacts due to demand for land. The Global Warming impact of the avoidable food waste was quantified between 2000 and 3600 kg CO 2 -eq. t -1 . The range reflected the different compositions of the waste in each sector. Prominent contributors to the impact, across all the environmental categories assessed, were land use changes and food production. Food preparation, for households and food service sectors, also provided an important contribution to the Global Warming impacts, while waste management partly mitigated the overall impacts by incurring significant savings when landfilling was replaced with anaerobic digestion and incineration. To further improve these results, it is recommended to focus future efforts on providing improved data regarding the breakdown of specific food products within the mixed waste, indirect land use change effects, and the share of food waste undergoing cooking. Learning from this and previous studies, we highlight the challenges related to modelling and methodological choices. Particularly, food production datasets should be chosen and used carefully, to avoid double counting and overestimation of the final impacts. Copyright © 2018 The Authors. Published by Elsevier Ltd.. All rights reserved.

Environmental impacts of waste incineration in a regional system (Emilia Romagna, Italy) evaluated from a life cycle perspective

International Nuclear Information System (INIS)

Morselli, Luciano; De Robertis, Claudia; Luzi, Joseph; Passarini, Fabrizio; Vassura, Ivano

2008-01-01

The advisability of using incineration, among the other technologies in Municipal Solid Waste Management, is still a debated issue. However, technological evolution in the field of waste incineration plants has strongly decreased their environmental impacts in the last years. A description of a regional situation in Northern Italy (Emilia Romagna Region) is here presented, to assess the impacts of incinerators by the application of Life Cycle Assessment (LCA) methodology and to stress the most impacting steps in incineration process. The management of solid residues and heavy metal emission resulted the most important environmental concerns. Furthermore, a tentative comparison with the environmental impact of landfill disposal, for the same amount of waste, pointed out that incineration process must be considered environmentally preferable

WASTE MINIMIZATION ASSESSMENT FOR A MANUFACTURER OF CUTTING AND WELDING EQUIPMENT

Science.gov (United States)

The U.S. Environmental Protection Agency (EPA) has funded a pilot program to assist small and medium-size manufacturers who want to minimize their generation of waste but who lack the expertise to do so in an effort to assist these manufacturers Waste Minimization Assessment Cent...

Proceedings of the US Department of Energy, Office of Environmental Restoration and Waste Management: Waste Reduction Workshop 6

International Nuclear Information System (INIS)

1991-04-01

The sixth of a series of waste reduction workshops was held at the Airport Hilton Hotel in Atlanta, Georgia, on February 6--7, 1991. These workshops are held under the auspices of the Department of Energy's (DOE's) Office of Environmental Restoration and Waste Management (EM). The focus of this workshop was the review of guidance and the status of conducting process waste assessments (PWAs). Other highlights of the workshop were the status of the Environmental Protection Agency's (EPA's) Pollution Prevention Program, and presentations on budgeting for waste reduction and the impact of the toxic release inventory (TRI) reporting requirements on pollution prevention activities. Concurrent sessions on the second day included case studies of the experiences at various sites on the subjects of recycling, incentives, source reduction, volume and toxicity reduction, and material procurement. The impact of new state laws on waste reduction efforts at Oak Ridge, Lawrence Livermore National Laboratory, and Hanford were also reviewed by representatives from those sites. These workshops assist DOE waste-generating sites in implementing waste minimization (WMIN) plans and programs, thus providing for optimal waste reduction within the DOE complex. All wastes are considered liquid, solid, and airborne, within the categories of high-level waste, transuranic waste (TRU), low-level waste (LLW), hazardous waste, mixed waste, office waste, and sanitary wastes. Topics of discussion within workshops encompass a wide range of subjects, including any method or technical activity from waste generation to disposal, such as process design or improvement, substitution of materials, waste segregation and recycling/reuse, waste treatment and processing, and administrative controls (procurement and waste awareness training). Consideration is also given to activities for remedial action and for decontamination and disposal

A probabilistic approach to assessing radioactive waste container lifetimes

International Nuclear Information System (INIS)

Porter, F.M.; Naish, C.C.; Sharland, S.M.

1994-01-01

A general methodology has been developed to make assessments of the lifetime of specific radioactive waste container designs in a repository environment. The methodology employs a statistical approach, which aims to reflect uncertainty in the corrosion rates, and the evolution of the environmental conditions. In this paper, the methodology is demonstrated for an intermediate-level waste (ILW) container in the anticipated UK repository situation

Environmental Impacts Assessment of Recycling of Construction and Demolition Waste

DEFF Research Database (Denmark)

Butera, Stefania

.e. soil and stones, concrete, asphalt and masonry, and as such it has the potential to be used as aggregate in the construction sector. A typical application is in an unbound state as filler in road structures. This practice offers evident benefits in terms of resource savings, however it might lead......Construction and demolition waste (C&DW) is waste derived from the construction, demolition and renovation of buildings and civil infrastructure. With 900 million tons generated every year in Europe, it is the largest waste stream on the continent. C&DW is mainly constituted of mineral fractions, i...... be evaluated critically.Owing to its high toxicity and significant mobility, especially at high pH levels, Cr(VI) is one of the elements of concern found in C&DW leachates. Its fate in the sub-soil below road applications was assessed experimentally, and its vertical migration was then predicted through...

Waste Isolation Pilot Plant 2005 Site Environmental Report

Energy Technology Data Exchange (ETDEWEB)

Washington Regulatory and Environmental Services

2006-10-13

The purpose of this report is to provide information needed by the DOE to assess WIPP's environmental performance and to make WIPP environmental information available to stakeholders and members of the public. This report has been prepared in accordance with DOE Order 231.1A and DOE guidance. This report documents WIPP's environmental monitoring programs and their results for 2004. The WIPP Project is authorized by the DOE National Security and Military Applications of Nuclear Energy Authorization Act of 1980 (Pub. L. 96-164). After more than 20 years of scientific study and public input, WIPP received its first shipment of waste on March 26, 1999. Located in southeastern New Mexico, WIPP is the nation's first underground repository permitted to safely and permanently dispose of TRU radioactive and mixed waste (as defined in the WIPP LWA) generated through defense activities and programs. TRU waste is defined, in the WIPP LWA, as radioactive waste containing more than 100 nanocuries (3,700 becquerels [Bq]) of alpha-emitting TRU isotopes per gram of waste, with half-lives greater than 20 years except for high-level waste, waste that has been determined not to require the degree of isolation required by the disposal regulations, and waste the U.S. Nuclear Regulatory Commission (NRC) has approved for disposal. Most TRU waste is contaminated industrial trash, such as rags and old tools; sludges from solidified liquids; glass; metal; and other materials from dismantled buildings. TRU waste is eligible for disposal at WIPP if it has been generated in whole or in part by one or more of the activities listed in the Nuclear Waste Policy Act of 1982 (42 United States Code [U.S.C.] §10101, et seq.), including naval reactors development, weapons activities, verification and control technology, defense nuclear materials production, defense nuclear waste and materials by-products management,defense nuclear materials security and safeguards and security

Environmental information document defense waste processing facility

International Nuclear Information System (INIS)

1981-07-01

This report documents the impact analysis of a proposed Defense Waste Processing Facility (DWPF) for immobilizing high-level waste currently being stored on an interim basis at the Savannah River Plant (SRP). The DWPF will process the waste into a form suitable for shipment to and disposal in a federal repository. The DWPF will convert the high-level waste into: a leach-resistant form containing above 99.9% of all the radioactivity, and a residue of slightly contaminated salt. The document describes the SRP site and environs, including population, land and water uses; surface and subsurface soils and waters; meteorology; and ecology. A conceptual integrated facility for concurrently producing glass waste and saltcrete is described, and the environmental effects of constructing and operating the facility are presented. Alternative sites and waste disposal options are addressed. Also environmental consultations and permits are discussed

Deliberate opinion of the Environmental Authority on the national plan for the management of radioactive materials and wastes (2016-2018)

International Nuclear Information System (INIS)

2016-01-01

In its first part, this document presents the context of national plans for the management of radioactive materials and wastes or PNGMDR (legal general principles, modalities of elaboration, framework), the project of PNGMDR for 2016-2018, its associated procedures, and the main environmental challenges noticed by the Environmental Authority. The second part proposes an analysis of the environmental assessment and notably explains the choice of this PNGMDR in terms of objectives for the environment, and with respect to other envisaged solutions. The third part describes how the PNGMDR takes the environment into account in terms of prevention, and of transverse environmental stakes. It also proposes an analysis in terms of material type and of wastes per sector (radioactive materials, wastes of different activity levels and life, residues, wastes with high natural radioactivity, management of historical sites). Two documents published by the IRSN, respectively on the environmental assessment of the PNGMDR and on a project of storage of low level and long life wastes are provided in appendix

Environmental system analysis of waste management. Experiences from applications of the ORWARE model

Energy Technology Data Exchange (ETDEWEB)

Bjoerklund, Anna

2000-11-01

Waste management has gone through a history of shifting problems, demands, and strategies over the years. In contrast to the long prevailing view that the problem could be solved by hiding or moving it, waste is now viewed as a problem ranging from local to global concern, and as being an integral part of several sectors in society. Decisive for this view has been society's increasing complexity and thus the increasing complexity of waste, together with a general development of environmental consciousness, moving from local focus on point emission sources, to regional and global issues of more complex nature. This thesis is about the development and application ORWARE; a model for computer aided environmental systems analysis of municipal waste management. Its origin is the hypothesis that widened perspectives are needed in waste management decision-making to avoid severe sub-optimisation of environmental performance. With a strong foundation in life cycle assessment (LCA), ORWARE aims to cover the environmental impacts over the entire life cycle of waste management. It also performs substance flow analysis (SFA) calculations at a rather detailed level of the system. Applying ORWARE has confirmed the importance of applying systems perspective and of taking into account site specific differences in analysis and planning of waste management, rather than relying on overly simplified solutions. Some findings can be generalised and used as guidelines to reduce environmental impact of waste management. Recovery of material and energy resources from waste generally leads to net reductions in energy use and environmental impact, because of the savings this brings about in other sectors. Waste treatment with low rate of energy and materials recovery should therefore be avoided. The exact choice of technology however depends on what products can be recovered and how they are used. Despite the complexity of the model and a certain degree of user unfriendliness, involved

DOE methods for evaluating environmental and waste management samples

International Nuclear Information System (INIS)

Goheen, S.C.; McCulloch, M.; Thomas, B.L.; Riley, R.G.; Sklarew, D.S.; Mong, G.M.; Fadeff, S.K.

1993-03-01

DOE Methods for Evaluating Environmental and Waste Management Samples (DOE Methods) provides applicable methods in use by. the US Department of Energy (DOE) laboratories for sampling and analyzing constituents of waste and environmental samples. The development of DOE Methods is supported by the Laboratory Management Division (LMD) of the DOE. This document contains chapters and methods that are proposed for use in evaluating components of DOE environmental and waste management samples. DOE Methods is a resource intended to support sampling and analytical activities that will aid in defining the type and breadth of contamination and thus determine the extent of environmental restoration or waste management actions needed, as defined by the DOE, the US Environmental Protection Agency (EPA), or others

DOE methods for evaluating environmental and waste management samples.

Energy Technology Data Exchange (ETDEWEB)

Goheen, S C; McCulloch, M; Thomas, B L; Riley, R G; Sklarew, D S; Mong, G M; Fadeff, S K [eds.; Pacific Northwest Lab., Richland, WA (United States)

1994-04-01

DOE Methods for Evaluating Environmental and Waste Management Samples (DOE Methods) provides applicable methods in use by. the US Department of Energy (DOE) laboratories for sampling and analyzing constituents of waste and environmental samples. The development of DOE Methods is supported by the Laboratory Management Division (LMD) of the DOE. This document contains chapters and methods that are proposed for use in evaluating components of DOE environmental and waste management samples. DOE Methods is a resource intended to support sampling and analytical activities that will aid in defining the type and breadth of contamination and thus determine the extent of environmental restoration or waste management actions needed, as defined by the DOE, the US Environmental Protection Agency (EPA), or others.

Quantitative assessments of municipal waste management systems: using different indicators to compare and rank programs in New York State.

Science.gov (United States)

Greene, Krista L; Tonjes, David J

2014-04-01

The primary objective of waste management technologies and policies in the United States is to reduce the harmful environmental impacts of waste, particularly those relating to energy consumption and climate change. Performance indicators are frequently used to evaluate the environmental quality of municipal waste systems, as well as to compare and rank programs relative to each other in terms of environmental performance. However, there currently is no consensus on the best indicator for performing these environmental evaluations. The purpose of this study is to examine the common performance indicators used to assess the environmental benefits of municipal waste systems to determine if there is agreement between them regarding which system performs best environmentally. Focus is placed on how indicator selection influences comparisons between municipal waste management programs and subsequent system rankings. The waste systems of ten municipalities in the state of New York, USA, were evaluated using each common performance indicator and Spearman correlations were calculated to see if there was a significant association between system rank orderings. Analyses showed that rank orders of waste systems differ substantially when different indicators are used. Therefore, comparative system assessments based on indicators should be considered carefully, especially those intended to gauge environmental quality. Insight was also gained into specific factors which may lead to one system achieving higher rankings than another. However, despite the insufficiencies of indicators for comparative quality assessments, they do provide important information for waste managers and they can assist in evaluating internal programmatic performance and progress. To enhance these types of assessments, a framework for scoring indicators based on criteria that evaluate their utility and value for system evaluations was developed. This framework was used to construct an improved model for

Evaluating environmental impacts of alternative construction waste management approaches using supply-chain-linked life-cycle analysis.

Science.gov (United States)

Kucukvar, Murat; Egilmez, Gokhan; Tatari, Omer

2014-06-01

Waste management in construction is critical for the sustainable treatment of building-related construction and demolition (C&D) waste materials, and recycling of these wastes has been considered as one of the best strategies in minimization of C&D debris. However, recycling of C&D materials may not always be a feasible strategy for every waste type and therefore recycling and other waste treatment strategies should be supported by robust decision-making models. With the aim of assessing the net carbon, energy, and water footprints of C&D recycling and other waste management alternatives, a comprehensive economic input-output-based hybrid life-cycle assessment model is developed by tracing all of the economy-wide supply-chain impacts of three waste management strategies: recycling, landfilling, and incineration. Analysis results showed that only the recycling of construction materials provided positive environmental footprint savings in terms of carbon, energy, and water footprints. Incineration is a better option as a secondary strategy after recycling for water and energy footprint categories, whereas landfilling is found to be as slightly better strategy when carbon footprint is considered as the main focus of comparison. In terms of construction materials' environmental footprint, nonferrous metals are found to have a significant environmental footprint reduction potential if recycled. © The Author(s) 2014.

Biomedical waste management: Incineration vs. environmental safety

Directory of Open Access Journals (Sweden)

Gautam V

2010-01-01

Full Text Available Public concerns about incinerator emissions, as well as the creation of federal regulations for medical waste incinerators, are causing many health care facilities to rethink their choices in medical waste treatment. As stated by Health Care Without Harm, non-incineration treatment technologies are a growing and developing field. Most medical waste is incinerated, a practice that is short-lived because of environmental considerations. The burning of solid and regulated medical waste generated by health care creates many problems. Medical waste incinerators emit toxic air pollutants and toxic ash residues that are the major source of dioxins in the environment. International Agency for Research on Cancer, an arm of WHO, acknowledged dioxins cancer causing potential and classified it as human carcinogen. Development of waste management policies, careful waste segregation and training programs, as well as attention to materials purchased, are essential in minimizing the environmental and health impacts of any technology.

Effect of a food waste disposer policy on solid waste and wastewater management with economic implications of environmental externalities.

Science.gov (United States)

Maalouf, Amani; El-Fadel, Mutasem

2017-11-01

In this study, the carbon footprint of introducing a food waste disposer (FWD) policy was examined in the context of its implications on solid waste and wastewater management with economic assessment of environmental externalities emphasizing potential carbon credit and increased sludge generation. For this purpose, a model adopting a life cycle inventory approach was developed to integrate solid waste and wastewater management processes under a single framework and test scenarios for a waste with high organic food content typical of developing economies. For such a waste composition, the results show that a FWD policy can reduce emissions by nearly ∼42% depending on market penetration, fraction of food waste ground, as well as solid waste and wastewater management schemes, including potential energy recovery. In comparison to baseline, equivalent economic gains can reach ∼28% when environmental externalities including sludge management and emissions variations are considered. The sensitivity analyses on processes with a wide range in costs showed an equivalent economic impact thus emphasizing the viability of a FWD policy although the variation in the cost of sludge management exhibited a significant impact on savings. Copyright © 2017 Elsevier Ltd. All rights reserved.

Environmental Restoration Progam Waste Minimization and Pollution Prevention Awareness Program Plan

Energy Technology Data Exchange (ETDEWEB)

Grumski, J. T.; Swindle, D. W.; Bates, L. D.; DeLozier, M. F.P.; Frye, C. E.; Mitchell, M. E.

1991-09-30

In response to DOE Order 5400.1 this plan outlines the requirements for a Waste Minimization and Pollution Prevention Awareness Program for the Environmental Restoration (ER) Program at Martin Marietta Energy System, Inc. Statements of the national, Department of Energy, Energy Systems, and Energy Systems ER Program policies on waste minimization are included and reflect the attitudes of these organizations and their commitment to the waste minimization effort. Organizational responsibilities for the waste minimization effort are clearly defined and discussed, and the program objectives and goals are set forth. Waste assessment is addressed as being a key element in developing the waste generation baseline. There are discussions on the scope of ER-specific waste minimization techniques and approaches to employee awareness and training. There is also a discussion on the process for continual evaluation of the Waste Minimization Program. Appendixes present an implementation schedule for the Waste Minimization and Pollution Prevention Program, the program budget, an organization chart, and the ER waste minimization policy.

Environmental Restoration Progam Waste Minimization and Pollution Prevention Awareness Program Plan

International Nuclear Information System (INIS)

1991-01-01

In response to DOE Order 5400.1 this plan outlines the requirements for a Waste Minimization and Pollution Prevention Awareness Program for the Environmental Restoration (ER) Program at Martin Marietta Energy System, Inc. Statements of the national, Department of Energy, Energy Systems, and Energy Systems ER Program policies on waste minimization are included and reflect the attitudes of these organizations and their commitment to the waste minimization effort. Organizational responsibilities for the waste minimization effort are clearly defined and discussed, and the program objectives and goals are set forth. Waste assessment is addressed as being a key element in developing the waste generation baseline. There are discussions on the scope of ER-specific waste minimization techniques and approaches to employee awareness and training. There is also a discussion on the process for continual evaluation of the Waste Minimization Program. Appendixes present an implementation schedule for the Waste Minimization and Pollution Prevention Program, the program budget, an organization chart, and the ER waste minimization policy

Modelling of environmental impacts from biological treatment of organic municipal waste in EASEWASTE

DEFF Research Database (Denmark)

Boldrin, Alessio; Neidel, Trine Lund; Damgaard, Anders

2011-01-01

The waste-LCA model EASEWASTE quantifies potential environmental effects from biological treatment of organic waste, based on mass and energy flows, emissions to air, water, soil and groundwater as well as effects from upstream and downstream processes. Default technologies for composting......, anaerobic digestion and combinations hereof are available in the model, but the user can change all key parameters in the biological treatment module so that specific local plants and processes can be modelled. EASEWASTE is one of the newest waste LCA models and the biological treatment module was built...... partly on features of earlier waste-LCA models, but offers additional facilities, more flexibility, transparency and user-friendliness. The paper presents the main features of the module and provides some examples illustrating the capability of the model in environmentally assessing and discriminating...

Environmental assessments required to support nomination of sites

International Nuclear Information System (INIS)

Mussler, R.M.

1984-01-01

The Nuclear Waste Policy Act of 1982 establishes a schedule for siting the nation's first repository for nuclear waste and spent fuel. The Act assigns the primary responsibility for conducting this siting program to the Department ofEnergy. The provisions of the Act are reviewed, including six legal requirements that must be considered for each environmental assessment, each of which is discussed in detail

Risk assessment and optimization (ALARA) analysis for the environmental remediation of Brookhaven National Laboratory's hazardous waste management facility

International Nuclear Information System (INIS)

Dionne, B.J.; Morris, S.C. III; Baum, J.W.

1998-01-01

The Department of Energy's (DOE) Office of Environment, Safety, and Health (EH) sought examples of risk-based approaches to environmental restoration to include in their guidance for DOE nuclear facilities. Extensive measurements of radiological contamination in soil and ground water have been made at Brookhaven National Laboratory's Hazardous Waste Management Facility (HWMF) as part of a Comprehensive Environmental Response, Compensation and Liability Act (CERCLA) remediation process. This provided an ideal opportunity for a case study. This report provides a risk assessment and an open-quotes As Low as Reasonably Achievableclose quotes (ALARA) analysis for use at other DOE nuclear facilities as an example of a risk-based decision technique. This document contains the Appendices for the report

Environmental assessment, Richton Dome site, Mississippi (US)

Energy Technology Data Exchange (ETDEWEB)

none,

1986-05-01

The Nuclear Waste Policy Act of 1982 (42 USC Sections 10101-10226) requires the environmental assessment of a potential site to include a statement of the basis for the nomination of a site as suitable for characterization. Volume 2 of this environmental assessment provides a detailed evaluation of the Richton Dome Site and its suitability as the site for a radioactive waste disposal facility under DOE siting guidelines, as well as a comparison of the Richton Dome site with other proposed sites. Evaluation of the Richton Dome site is based on the reference repository design, but the evaluation will not change if based on the Mission Plan repository concept. The comparative evaluation of proposed sites is required under DOE guidelines, but is not intended to directly support the subsequent recommendation of three sites for characterization as candidate sites. 428 refs., 24 figs., 62 tabs. (MHB)

Hazard waste risk assessment

International Nuclear Information System (INIS)

Hawley, K.A.; Napier, B.A.

1986-01-01

Pacific Northwest Laboratory continued to provide technical assistance to the Department of Energy (DOE) Office of Operational Safety (OOS) in the area of risk assessment for hazardous and radioactive-mixed waste management. The overall objective is to provide technical assistance to OOS in developing cost-effective risk assessment tools and strategies for bringing DOE facilities into compliance with the Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA or Superfund) and the Resource Conservation and Recovery Act (RCRA). Major efforts during FY 1985 included (1) completing the modification of the Environmental Protection Agency (EPA) Hazard Ranking System (HRS) and developing training manuals and courses to assist in field office implementation of the modified Hazard Ranking System (mHRS); (2) initiating the development of a system for reviewing field office HRS/mHRS evaluations for appropriate use of data and appropriate application of the methodology; (3) initiating the development of a data base management system to maintain all field office HRS/mHRS scoring sheets and to support the master OOS environmental data base system; (4) developing implementation guidance for Phase I of the DOE CERCLA Program, Installation Assessment; (5) continuing to develop an objective, scientifically based methodology for DOE management to use in establishing priorities for conducting site assessments under Phase II of the DOE CERCLA Program, Confirmation; and (6) participating in developing the DOE response to EPA on the proposed listing of three sites on the National Priorities List

Applications of life cycle assessment and cost analysis in health care waste management

International Nuclear Information System (INIS)

Soares, Sebastião Roberto; Finotti, Alexandra Rodrigues; Prudêncio da Silva, Vamilson; Alvarenga, Rodrigo A.F.

2013-01-01

Highlights: ► Three Health Care Waste (HCW) scenarios were assessed through environmental and cost analysis. ► HCW treatment using microwave oven had the lowest environmental impacts and costs in comparison with autoclave and lime. ► Lime had the worst environmental and economic results for HCW treatment, in comparison with autoclave and microwave. - Abstract: The establishment of rules to manage Health Care Waste (HCW) is a challenge for the public sector. Regulatory agencies must ensure the safety of waste management alternatives for two very different profiles of generators: (1) hospitals, which concentrate the production of HCW and (2) small establishments, such as clinics, pharmacies and other sources, that generate dispersed quantities of HCW and are scattered throughout the city. To assist in developing sector regulations for the small generators, we evaluated three management scenarios using decision-making tools. They consisted of a disinfection technique (microwave, autoclave and lime) followed by landfilling, where transportation was also included. The microwave, autoclave and lime techniques were tested at the laboratory to establish the operating parameters to ensure their efficiency in disinfection. Using a life cycle assessment (LCA) and cost analysis, the decision-making tools aimed to determine the technique with the best environmental performance. This consisted of evaluating the eco-efficiency of each scenario. Based on the life cycle assessment, microwaving had the lowest environmental impact (12.64 Pt) followed by autoclaving (48.46 Pt). The cost analyses indicated values of US$ 0.12 kg −1 for the waste treated with microwaves, US$ 1.10 kg −1 for the waste treated by the autoclave and US$ 1.53 kg −1 for the waste treated with lime. The microwave disinfection presented the best eco-efficiency performance among those studied and provided a feasible alternative to subsidize the formulation of the policy for small generators of HCW.

Department of Energy's process waste assessment graded approach methodology

International Nuclear Information System (INIS)

Pemberton, S.E.

1994-03-01

As the initial phase of the formal waste minimization program, the Department of Energy requires assessments of all its waste-generating operations. These assessments, called process waste assessments (PWAs), are a tool which helps achieve the pollution prevention goals. The DOE complex is comprised of numerous sites located in many different states. The facilities as a whole represent a tremendous diversity of technologies, processes, and activities. Due to this diversity, there are also a wide variety and number of waste streams generated. Many of these waste streams are small, intermittent, and not of consistent composition. The PWA graded approach methodology addresses these complexities and recognizes that processes vary in the quantity of pollution they generate, as well as in the perceived risk and associated hazards. Therefore, the graded approach was developed to provide a cost-effective and flexible methodology which allows individual sites to prioritize their local concerns and align their efforts with the resources allocated. This presentation will describe a project sponsored by the DOE Office of Environmental Restoration and Waste Management, Waste Minimization Division, which developed a graded approach methodology for use throughout the DOE. This methodology was initiated in FY93 through a combined effort of the following DOE/Defense Program sites: Kansas City Plant, Lawrence Livermore National Laboratory, Los Alamos National Laboratory, Sandia National Laboratories. This presentation will describe the process waste assessment tool, benefits achieved through the completion of PWAs, DOE's graded approach methodology, and an update on the project's current status

Probabilistic safety assessment for Hanford high-level waste tanks

International Nuclear Information System (INIS)

MacFarlane, D.R.; Stack, D.S.; Kindinger, J.P.; Deremer, R.K.

1995-01-01

This paper gives results from the first comprehensive level-3 probabilistic safety assessment (PSA), including consideration of external events, for the Hanford tank farm (HTF). This work was sponsored by the U.S. Department of Energy/Environmental Restoration and Waste Management Division (DOE/EM). At the HTF, there are 177 underground tanks in 18 separate tank farms containing accumulated liquid/sludge/saltcake radioactive wastes from 50 yr of weapons materials production activities. The total waste volume is ∼60 million gal, containing ∼200 million Ci of radioactivity

Assessment of mixed hazardous and radioactive waste sites at Hanford

International Nuclear Information System (INIS)

McLaughlin, T.J.; Cramer, K.H.; Lamar, D.A.; Sherwood, D.R.; Stenner, R.D.; Schulze, W.B.

1987-10-01

The US Department of Energy and Pacific Northwest Laboratory recently completed a preliminary assessment of 685 inactive hazardous waste sites located on the Hanford Site. The preliminary assessment involved collecting historical data and individual site information, conducting site inspections, and establishing an environmental impact priority, using the Hazard Ranking System, for each of these 685 sites. This preliminary assessment was the first step in the remediation process required by the Comprehensive Environmental Response, Compensation and Liability Act. This paper presents the results of that preliminary assessment. 10 refs., 4 figs., 1 tab

Environmental assessment process needs and future directions

Energy Technology Data Exchange (ETDEWEB)

Gustafson, P.F.

1985-01-01

The environmental assessment process as legislatively mandated by the National Environmental Policy Act of 1969 (NEPA) constitutes a double-edged sword as regards the successful management and disposal of radioactive waste. On the one hand, NEPA requires identification and disclosure of the environmental and societal consequences of a given major federal action, consideration of alternatives and/or mitigative measures leading to the same end result, a balancing of costs and benefits, and provides for and encourages public participation in the decision-making process regarding the proposed action(s). On the other hand, public participation supported by judicial decisions, based more upon procedural than substantive issues, may delay, alter, or indeed prohibit a proposed course of action. If the cognizant federal agencies (DOE and NRC in the radioactive waste area) comply with both the spirit and the letter of NEPA a framework for the successful management of radioactive wastes on all types can be developed. If however, these agencies are less than earnest in their NEPA compliance actions or if public opposition is backed by overzealous court action, any radioactive waste management/disposal action (however technically sound) can be hoisted upon a petard from which it may not be freed until well into the next century.

Environmental assessment process needs and future directions

International Nuclear Information System (INIS)

Gustafson, P.F.

1985-01-01

The environmental assessment process as legislatively mandated by the National Environmental Policy Act of 1969 (NEPA) constitutes a double-edged sword as regards the successful management and disposal of radioactive waste. On the one hand, NEPA requires identification and disclosure of the environmental and societal consequences of a given major federal action, consideration of alternatives and/or mitigative measures leading to the same end result, a balancing of costs and benefits, and provides for and encourages public participation in the decision-making process regarding the proposed action(s). On the other hand, public participation supported by judicial decisions, based more upon procedural than substantive issues, may delay, alter, or indeed prohibit a proposed course of action. If the cognizant federal agencies (DOE and NRC in the radioactive waste area) comply with both the spirit and the letter of NEPA a framework for the successful management of radioactive wastes on all types can be developed. If however, these agencies are less than earnest in their NEPA compliance actions or if public opposition is backed by overzealous court action, any radioactive waste management/disposal action (however technically sound) can be hoisted upon a petard from which it may not be freed until well into the next century

National environmental radiation monitoring program: towards formulating policy on radioactive waste management

International Nuclear Information System (INIS)

Sukiman Sarmani

2002-01-01

Though Malaysia has no nuclear power station, but the management of its low level radioactive waste generated from industrial activities involves most of the same issues that must be considered in countries with nuclear power. These include public consultation at all stages, an open approach, high level scientific and engineering input and political decision by the Government. A carefully planned approach, which involves the public and gives time to build trust and confidence, is necessary for success. It is also pertinent to establish accurate and reliable data on environmental radiation to accurately assess possible risk. This is where a national monitoring program on environmental radiation is very important. While accurate data will help formulate sound policy on radioactive waste management, it should also be readily available to the public to gain support and acceptance. This paper presents arguments on the importance of a national monitoring program for environmental radiation as an input for formulating a policy on radioactive waste management in Malaysia. (Author)