Reliability in Plantinga´s Account of Epistemic Warrant

Directory of Open Access Journals (Sweden)

John C. Wingard, Jr.

2002-12-01

Full Text Available In das paper 1 consider the reliability condition in Alvin Platinga’s proper functionalist account of epistemic warrant I begin by reviewing m some detail the features of the reliability condition as Platinga has articulated a From there, 1 consider what is needed to ground or secure the sort of reliability which Plantinga has m mind, and argue that what is needed is a significant causal condition which has generally been overlooked Then, after identifying eight versions of the relevant sort of reliability, I exam me each alternative as to whether as requirement, along with Platinga’s other proposed conditions, would give us a satisfactory account of epistemic warrant I conclude that there is bale to no hope of formulating a reliability condition that would yield a satisfactory analysts of the sort Plantinga desires

Behavioral Preferences for Individual Securities : The Case for Call Warrants and Call Options

NARCIS (Netherlands)

Ter Horst, J.R.; Veld, C.H.

2002-01-01

Since 1998, large investment banks have flooded the European capital markets with issues of call warrants.This has led to a unique situation in the Netherlands, where now call warrants, traded on the stock exchange, and long-term call options, traded on the options exchange, exist.Both entitle their

Test Procedure - pumping system for caustic addition project

International Nuclear Information System (INIS)

Leshikar, G.A.

1994-01-01

This test procedure provides the requirements for sub-system testing and integrated operational testing of the submersible mixer pump and caustic addition equipment by WHC and Kaiser personnel at the Rotating Equipment Shop run-in pit (Bldg. 272E)

The valuation of equity warrants under the fractional Vasicek process of the short-term interest rate

Science.gov (United States)

Xiao, Weilin; Zhang, Weiguo; Zhang, Xili; Chen, Xiaoyan

2014-01-01

Motivated by the empirical evidence of long range dependence in short-term interest rates and considering the long maturities of equity warrants, we propose the fractional Vasicek model to describe the dynamics of the short rate in the pricing environment of equity warrants. Using the partial differential equation approach, we present a valuation model for equity warrants under the assumption that the short rate follows the fractional Vasicek process. After identifying the pricing model for equity warrants, we provide the parameter estimation procedure for the proposed pricing model. Since obtaining the values of equity warrants from the proposed model needs to solve a nonlinear equation, we employ a hybrid intelligent algorithm to get around this optimization problem. Furthermore, to illustrate the practicality of our proposed model, we conduct an empirical study to ascertain the performance of our proposed model using the data from China’s warrant market and the China Foreign Exchange Trade System. The comparison of traditional models (such as the Black-Scholes model, the Noreen-Wolfson model, the Lauterbach-Schultz model, and the Ukhov model) with our proposed model is also presented. The empirical results show that the mean absolute percentage error of our pricing model is 10.30%. By contrast, the Black-Scholes model, the Noreen-Wolfson model, the Lauterbach-Schultz model, and the Ukhov model applied to the same warrant produce mean absolute errors of 35.26%, 37.67%, 33.40%, 32.81%, respectively. Thus the long memory property in stochastic interest rates cannot be ignored in determining the valuation of equity warrants.

Intraday Trading Patterns in the Equity Warrants and Equity Options Markets: Australian Evidence

Directory of Open Access Journals (Sweden)

Lydia Segara

2007-06-01

Full Text Available This paper extends the microstructure literature, by examining the previouslyundocumented intraday trading patterns in trading volume, price volatility, order depthand relative spreads for both the warrant and option market in Australia. Comparisons ofintraday variations across these derivative securities allows for insight to be drawn intocompeting market microstructure theories and provides the opportunity to examinewhether market design differences explain variations in observed intraday patterns. Wefind that intraday trading patterns documented in the warrant and option markets can beexplained by their market designs, along with theories relating to time-varying informationasymmetry and time-varying hedging trades around nontrading periods.

Design of Test Parts to Characterize Micro Additive Manufacturing Processes

DEFF Research Database (Denmark)

Thompson, Mary Kathryn; Mischkot, Michael

2015-01-01

The minimum feature size and obtainable tolerances of additive manufacturing processes are linked to the smallest volumetric elements (voxels) that can be created. This work presents the iterative design of a test part to investigate the resolution of AM processes with voxel sizes at the micro...... scale. Each design iteration reduces the test part size, increases the number of test features, improves functionality, and decreases coupling in the part. The final design is a set of three test parts that are easy to orient and measure, and that provide useful information about micro additive...... manufacturing processes....

Basophil activation test with food additives in chronic urticaria patients.

Science.gov (United States)

Kang, Min-Gyu; Song, Woo-Jung; Park, Han-Ki; Lim, Kyung-Hwan; Kim, Su-Jung; Lee, Suh-Young; Kim, Sae-Hoon; Cho, Sang-Heon; Min, Kyung-Up; Chang, Yoon-Seok

2014-01-01

The role of food additives in chronic urticaria (CU) is still under investigation. In this study, we aimed to explore the association between food additives and CU by using the basophil activation test (BAT). The BAT using 15 common food additives was performed for 15 patients with CU who had a history of recurrent urticarial aggravation following intake of various foods without a definite food-specific IgE. Of the 15 patients studied, two (13.3%) showed positive BAT results for one of the tested food additives. One patient responded to monosodium glutamate, showing 18.7% of CD203c-positive basophils. Another patient showed a positive BAT result to sodium benzoate. Both patients had clinical correlations with the agents, which were partly determined by elimination diets. The present study suggested that at least a small proportion of patients with CU had symptoms associated with food additives. The results may suggest the potential utility of the BAT to identity the role of food additives in CU.

Is a comparative clinical trial for breast cancer tumor markers to monitor disease recurrence warranted? A value of information analysis.

Science.gov (United States)

Thariani, Rahber; Henry, Norah Lynn; Ramsey, Scott D; Blough, David K; Barlow, Bill; Gralow, Julie R; Veenstra, David L

2013-05-01

Breast cancer tumor markers are used by some clinicians to screen for disease recurrence risk. Since there is limited evidence of benefit, additional research may be warranted. To assess the potential value of a randomized clinical trial of breast tumor marker testing in routine follow-up of high-risk, stage II-III breast cancer survivors. We developed a decision-analytic model of tumor marker testing plus standard surveillance every 3-6 months for 5 years. The expected value of sample information was calculated using probabilistic simulations and was a function of: the probability of selecting the optimal monitoring strategy with current versus future information; the impact of choosing the nonoptimal strategy; and the size of the population affected. The value of information for a randomized clinical trial involving 9000 women was US$214 million compared with a cost of US$30-60 million to conduct such a trial. The probability of making an alternate, nonoptimal decision and choosing testing versus no testing was 32% with current versus future information from the trial. The impact of a nonoptimal decision was US$2150 and size of population impacted over 10 years was 308,000. The value of improved information on overall survival was US$105 million, quality of life US$37 million and test performance US$71 million. Conducting a randomized clinical trial of breast cancer tumor markers appears to offer a good societal return on investment. Retrospective analyses to assess test performance and evaluation of patient quality of life using tumor markers may also offer valuable areas of research. However, alternative investments may offer even better returns in investments and, as such, the trial concept deserves further study as part of an overall research-portfolio evaluation.

Right-­turn traffic volume adjustment in traffic signal warrant analysis : final report.

Science.gov (United States)

2016-05-06

This report was based on the research project, Right-Turn Traffic Volume Adjustment in Traffic Signal Warrants, sponsored by the Nevada Department of Transportation (NDOT) and SOLARIS. Right-turn traffic does not affect intersection performance in th...

Feasibility and Testing of Additive Manufactured Components

Energy Technology Data Exchange (ETDEWEB)

Dehoff, Ryan R [ORNL; Hummelt, Ed [Eaton Corporation; Solovyeva, Lyudmila [Eaton Corporation

2016-09-01

This project focused on demonstrating the ability to fabricate two parts with different geometry: an arc flash interrupter and a hydraulic manifold. Eaton Corporation provided ORNL solid models, information related to tolerances and sensitive parameters of the parts and provided testing and evaluation. ORNL successfully manufactured both components, provided cost models of the manufacturing (materials, labor, time and post processing) and delivered test components for Eaton evaluation. The arc flash suppressor was fabricated using the Renishaw laser powder bed technology in CoCrMo while the manifold was produced from Ti-6Al-4V using the Arcam electron beam melting technology. These manufacturing techniques were selected based on the design and geometrical tolerances required. A full-scale manifold was produced on the Arcam A2 system (nearly 12 inches tall). A portion of the manifold was also produced in the Arcam Q10 system. Although a full scale manifold could not be produced in the system, a full scale manifold is expected to have similar material properties, geometric accuracy, and surface finish as could be fabricated on an Arcam Q20 system that is capable of producing four full scale manifolds in a production environment. In addition to the manifold, mechanical test specimens, geometric tolerance artifacts, and microstructure samples were produced alongside the manifold. The development and demonstration of these two key components helped Eaton understand the impact additive manufacturing can have on many of their existing products. By working within the MDF and leveraging ORNL’s manufacturing and characterization capabilities, the work will ensure the rapid insertion and commercialization of this technology.

From Four to Two: Transformation of the Army Ordnance Officer and Warrant Officer Corps

National Research Council Canada - National Science Library

Napier, Joyce

2003-01-01

.... This study will examine how senior leaders within the Army and specifically the Ordnance Corps must change the officer and warrant officer force structure education system and leader development...

The effects of additive outliers on tests for unit roots and cointegration

NARCIS (Netherlands)

Ph.H.B.F. Franses (Philip Hans); N. Haldrup (Niels)

1994-01-01

textabstractThe properties of the univariate Dickey-Fuller test and the Johansen test for the cointegrating rank when there exist additive outlying observations in the time series are examined. The analysis provides analytical as well as numerical evidence that additive outliers may produce spurious

Is Patch Testing with Food Additives Useful in Children with Atopic Eczema?

Science.gov (United States)

Catli, Gonul; Bostanci, Ilknur; Ozmen, Serap; Dibek Misirlioglu, Emine; Duman, Handan; Ertan, Ulker

2015-01-01

Atopy patch testing is a useful way to determine delayed-type hypersensitivity reactions to foods and aeroallergens. Although food additives have been accused of worsening atopic eczema symptoms, according to recent studies the role of food additives in atopic eczema remains unclear. The purpose of our study was to investigate food additive hypersensitivity in a group of children with atopic eczema by using standardized atopy patch testing and to determine the role of food additive hypersensitivity in atopic eczema. Thirty-four children with atopic eczema and 33 healthy children were enrolled in the study. Children who consumed foods containing additives and did not use either antihistamines or local or systemic corticosteroids for at least 7 days prior to admission were enrolled in the study. All children were subjected to atopy patch testing and after 48 and 72 hours their skin reactions were evaluated by using the guidelines. Positive atopy patch test results were significantly higher in the atopic eczema group. Forty-one percent of the atopic eczema group (n = 14) and 15.2% (n = 5) of the control group had positive atopy patch test results with food additives (p = 0.036) (estimated relative risk 1.68, case odds 0.7, control odds 0.17). Carmine hypersensitivity and the consumption of foods containing carmine, such as gumdrops, salami, and sausage, were significantly higher in the children with atopic eczema. This is the first study investigating hypersensitivity to food additives in children with atopic eczema. Our results indicate that carmine may play a role in atopic eczema. © 2015 Wiley Periodicals, Inc.

A review on Black-Scholes model in pricing warrants in Bursa Malaysia

Science.gov (United States)

Gunawan, Nur Izzaty Ilmiah Indra; Ibrahim, Siti Nur Iqmal; Rahim, Norhuda Abdul

2017-01-01

This paper studies the accuracy of the Black-Scholes (BS) model and the dilution-adjusted Black-Scholes (DABS) model to pricing some warrants traded in the Malaysian market. Mean Absolute Error (MAE) and Mean Absolute Percentage Error (MAPE) are used to compare the two models. Results show that the DABS model is more accurate than the BS model for the selected data.

Peculiarities of the Enforcement of the European Arrest Warrant in the Case of an Illegal Liberty Deprivation

Directory of Open Access Journals (Sweden)

Minodora Ioana Rusu

2010-06-01

Full Text Available The illegal deprivation of liberty is, under the current context, one of the most serious offenses, being treated differently in the European Union. The need to prevent and combat this violation, it has led the European legislator to include it under different names in the European legislative act that governs the institution of the European arrest warrant. In this context, the European arrest warrant is the most important form of judicial cooperation in penal matters between the Member States of the EU, which is based on mutualrecognition of criminal judgments. The research conducted on how it is regulated the enforcement of the European arrest warrant in the case of illegal liberty deprivation in the European legislative act (the Framework Decision 2002/584/JHA leads to the conclusion that the legislature failed to mention the violation in question in the group of the violation for which it was not necessary the inspection of the double incrimination, but, still, including the offenses as kidnapping, illegal restraint and hostage-taking. Even if theRomanian legislator included this violation in the above mentioned group, this situation is not solved, because it will cause some problems in the request by the Romanian judicial authorities of the enforcement of such warrant. Another criticized issue, observed not only in the European legislative act, but also in the internal law, is related to the lack of stipulations, which can lead to the possibility of issuing and executing a European arrest warrant and for the execution of educational measures for illegal deprivation of liberty and also others. Also, in order to increase the effectiveness of the execution of a European arrest warrant, we consider that it should be granted executive powers of all courts of Romania. The originality of the work consists of the critical observations and the lege ferenda proposal which covers both the European legislativeact and the Romanian Law. At the same time

Right-\\0xADturn traffic volume adjustment in traffic signal warrant analysis : final report.

Science.gov (United States)

2016-05-06

This report was based on the research project, Right-Turn Traffic Volume Adjustment in : Traffic Signal Warrants, sponsored by the Nevada Department of Transportation (NDOT) : and SOLARIS. Right-turn traffic does not affect intersection performance i...

Clinical pathways for inborn errors of metabolism: warranted and feasible

Directory of Open Access Journals (Sweden)

Demirdas Serwet

2013-02-01

Full Text Available Abstract Inborn errors of metabolism (IEMs are known for their low prevalence and multidisciplinary care mostly founded on expert opinion. Clinical pathways are multidisciplinary tools to organise care which provide a clear route to the best care and improve communication. In 2010 the Dutch Society for Children and Adults with an Inborn Error of Metabolism (VKS initiated development of clinical pathways for inborn errors of metabolism. In this letter to the editor we describe why it is warranted to develop clinical pathways for IEMs and shortly discuss the process of development for these pathways in the Netherlands.

Is Bringing Back Warrant Officers the Answer A Loot at How They Could Work in the Air Force Cyber Operations Career Field

Science.gov (United States)

2017-03-16

fulfill that intent. In contrast, the Army, Navy and Marine Corps utilize warrant officers in a multitude of capacities, especially in highly... education and more generalized knowledge of commissioned officers. Warrant officer duties include supervising and managing the execution of cyberspace...trace his or her roots back to the British Royal Navy in the thirteenth century.28 The Crown awarded Royal Warrants to especially experienced sailors to

A Note on the Vogelsang Test for Additive Outliers

DEFF Research Database (Denmark)

Haldrup, Niels; Sansó, Andreu

The role of additive outliers in integrated time series has attractedsome attention recently and research shows that outlier detection shouldbe an integral part of unit root testing procedures. Recently, Vogelsang(1999) suggested an iterative procedure for the detection of multiple additiveoutliers...... in integrated time series. However, the procedure appearsto suffr from serious size distortions towards the finding of too manyoutliers as has been shown by Perron and Rodriguez (2003). In this notewe prove the inconsistency of the test in each step of the iterative procedureand hence alternative routes need...

Show me the goods: The warranting effect of user-generated photographs in online auctions

NARCIS (Netherlands)

Johnson, B.K.; Vang, M.H.; van der Heide, B.

2015-01-01

Consumers using online auction websites face the challenge of appraising products at a distance. Sellers and buyers in online auctions navigate this challenge by displaying and evaluating various cues, a critical one being use of photographs. Warranting theory predicts that cues less subject to

49 CFR 173.466 - Additional tests for Type A packagings designed for liquids and gases.

Science.gov (United States)

2010-10-01

... 49 Transportation 2 2010-10-01 2010-10-01 false Additional tests for Type A packagings designed...) Materials § 173.466 Additional tests for Type A packagings designed for liquids and gases. (a) In addition to the tests prescribed in § 173.465, Type A packagings designed for liquids and gases must be...

Computerized adaptive testing--ready for ambulatory monitoring?

DEFF Research Database (Denmark)

Rose, Matthias; Bjørner, Jakob; Fischer, Felix

2012-01-01

Computerized adaptive tests (CATs) have abundant theoretical advantages over established static instruments, which could improve ambulatory monitoring of patient-reported outcomes (PROs). However, an empirical demonstration of their practical benefits is warranted.......Computerized adaptive tests (CATs) have abundant theoretical advantages over established static instruments, which could improve ambulatory monitoring of patient-reported outcomes (PROs). However, an empirical demonstration of their practical benefits is warranted....

Project Rio Blanco definition plan. Additional formation evaluation and production testing

International Nuclear Information System (INIS)

1975-09-01

Since the multiple Rio Blanco detonation three reentry wells have been drilled for test purposes: RB-E-01 (Emplacement Well); RB-AR-2 (Alternate Reentry Well); and RB-U-4 (Formation Evaluation Well). Additional testing in all these wells is now required to resolve some remaining technical questions. A plan describing the procedures, methods, responsibilities, and scheduling of the field operations is presented

Advanced Manufacturing Technologies (AMT): Additive Manufactured Hot Fire Planning and Testing in GRC Cell 32 Project

Science.gov (United States)

Fikes, John C.

2014-01-01

The objective of this project is to hot fire test an additively manufactured thrust chamber assembly TCA (injector and thrust chamber). GRC will install the additively manufactured Inconel 625 injector, two additively manufactured (SLM) water cooled Cu-Cr thrust chamber barrels and one additively manufactured (SLM) water cooled Cu-Cr thrust chamber nozzle on the test stand in Cell 32 and perform hot fire testing of the integrated TCA.

Varant Yatırımcısının Volatilite Algısına Etki Eden Faktörler: BIST’de Ampirik Bir Uygulama(Factors Affecting the Volatility Perception of Warrant Investors: An Empirical Research on BIST

Directory of Open Access Journals (Sweden)

İsrafil ZOR

2013-12-01

Full Text Available The aim of the study is to determine the factors that affect the volatility perception of warrant investors. By using 3.187 daily data of 61 call warrants whose underlying asset is BIST-30 Index and traded on BIST in 2012, firstly efficient option pricing model for the related market is confirmed and then volatilities that equalizes the efficient model prices to market prices are calculated and regression analysis is applied to determine factors that affect the volatility. The results of the analysis are revealed that if the closing price of the underlying asset, the days to maturity of the warrant and Turkish Lira Interbank rate increase, the volatility perceived by investors will decrease. Also, there is positive relationship between the closing price of warrants and the perceived volatility. In addition perceived volatility is higher on Monday and first decrease in inflation after 4 months increase reduces the perceived volatility.

The effect of testing versus restudy on retention: a meta-analytic review of the testing effect.

Science.gov (United States)

Rowland, Christopher A

2014-11-01

Engaging in a test over previously studied information can serve as a potent learning event, a phenomenon referred to as the testing effect. Despite a surge of research in the past decade, existing theories have not yet provided a cohesive account of testing phenomena. The present study uses meta-analysis to examine the effects of testing versus restudy on retention. Key results indicate support for the role of effortful processing as a contributor to the testing effect, with initial recall tests yielding larger testing benefits than recognition tests. Limited support was found for existing theoretical accounts attributing the testing effect to enhanced semantic elaboration, indicating that consideration of alternative mechanisms is warranted in explaining testing effects. Future theoretical accounts of the testing effect may benefit from consideration of episodic and contextually derived contributions to retention resulting from memory retrieval. Additionally, the bifurcation model of the testing effect is considered as a viable framework from which to characterize the patterns of results present across the literature. (PsycINFO Database Record (c) 2014 APA, all rights reserved).

On Bayesian Testing of Additive Conjoint Measurement Axioms Using Synthetic Likelihood.

Science.gov (United States)

Karabatsos, George

2018-06-01

This article introduces a Bayesian method for testing the axioms of additive conjoint measurement. The method is based on an importance sampling algorithm that performs likelihood-free, approximate Bayesian inference using a synthetic likelihood to overcome the analytical intractability of this testing problem. This new method improves upon previous methods because it provides an omnibus test of the entire hierarchy of cancellation axioms, beyond double cancellation. It does so while accounting for the posterior uncertainty that is inherent in the empirical orderings that are implied by these axioms, together. The new method is illustrated through a test of the cancellation axioms on a classic survey data set, and through the analysis of simulated data.

Diagnosing true virtue? Remote scenarios, warranted virtue attributions, and virtuous medical practice.

Science.gov (United States)

Oakley, Justin

2016-02-01

Immanuel Kant argues in the Foundations that remote scenarios are diagnostic of genuine virtue. When agents commonly thought to have a particular virtue fail to exhibit that virtue in an extreme situation, he argues, they do not truly have the virtue at all, and our propensities to fail in such ways indicate that true virtue might never have existed. Kant's suggestion that failure to show, say, courage in extraordinary circumstances necessarily silences one's claim to have genuine courage seems to rely on an implausibly demanding standard for warranted virtue attributions. In contrast to this approach, some philosophers-such as Robert Adams and John Doris-have argued for probabilistic accounts of warranted virtue attributions. But despite the initial plausibility of such accounts, I argue that a sole reliance on probabilistic approaches is inadequate, as they are insufficiently sensitive to considerations of credit and fault, which emerge when agents have developed various insurance strategies and protective capacities against their responding poorly to particular eventualities. I also argue that medical graduates should develop the sorts of virtuous dispositions necessary to protect patient welfare against various countervailing influences (even where such influences might be encountered only rarely), and that repeated failures to uphold the proper goals of medicine in emergency scenarios might indeed be diagnostic of whether an individual practitioner does have the relevant medical virtue. In closing, I consider the dispositions involved in friendship. I seek to develop a principled way of determining when remote scenarios can be illuminating of genuine friendship and genuine virtue.

Results of industrial tests of carbonate additive to fuel oil

Science.gov (United States)

Zvereva, E. R.; Dmitriev, A. V.; Shageev, M. F.; Akhmetvalieva, G. R.

2017-08-01

Fuel oil plays an important role in the energy balance of our country. The quality of fuel oil significantly affects the conditions of its transport, storage, and combustion; release of contaminants to atmosphere; and the operation of main and auxiliary facilities of HPPs. According to the Energy Strategy of Russia for the Period until 2030, the oil-refining ratio gradually increases; as a result, the fraction of straight-run fuel oil in heavy fuel oils consistently decreases, which leads to the worsening of performance characteristics of fuel oil. Consequently, the problem of the increase in the quality of residual fuel oil is quite topical. In this paper, it is suggested to treat fuel oil by additives during its combustion, which would provide the improvement of ecological and economic indicators of oil-fired HPPs. Advantages of this method include simplicity of implementation, low energy and capital expenses, and the possibility to use production waste as additives. In the paper, the results are presented of industrial tests of the combustion of fuel oil with the additive of dewatered carbonate sludge, which is formed during coagulation and lime treatment of environmental waters on HPPs. The design of a volume delivery device is developed for the steady additive input to the boiler air duct. The values are given for the main parameters of the condition of a TGM-84B boiler plant. The mechanism of action of dewatered carbonate sludge on sulfur oxides, which are formed during fuel oil combustion, is considered. Results of industrial tests indicate the decrease in the mass fraction of discharged sulfur oxides by 36.5%. Evaluation of the prevented damage from sulfur oxide discharged into atmospheric air shows that the combustion of the fuel oil of 100 brand using carbonate sludge as an additive (0.1 wt %) saves nearly 6 million rubles a year during environmental actions at the consumption of fuel oil of 138240 t/year.

Generalized requirements and decompositions for the design of test parts for micro additive manufacturing research

DEFF Research Database (Denmark)

Thompson, Mary Kathryn; Clemmensen, Line Katrine Harder

2015-01-01

The design of experimental test parts to characterize micro additive manufacturing (AM) processes is challenging due to the influence of the manufacturing and metrology processes. This work builds on the lessons learned from a case study in the literature to derive generalized requirements and high...... level decompositions for the design of test parts and the design of experiments to characterize micro additive manufacturing processes. While the test parts and the experiments described are still work in progress, the generic requirements derived from them can serve as a starting point for the design...... of other micro additive manufacturing related studies and their decompositions can help structure future work....

20 CFR 416.934 - Impairments which may warrant a finding of presumptive disability or presumptive blindness.

Science.gov (United States)

2010-04-01

... Blindness Presumptive Disability and Blindness § 416.934 Impairments which may warrant a finding of presumptive disability or presumptive blindness. We may make findings of presumptive disability and... school, because of mental deficiency or is unable to attend any type of school (or if beyond school age...

Sensitization to Food Additives in Patients with Allergy: A Study Based on Skin Test and Open Oral Challenge.

Science.gov (United States)

Moghtaderi, Mozhgan; Hejrati, Zinatosadat; Dehghani, Zahra; Dehghani, Faranak; Kolahi, Niloofar

2016-06-01

There has been a great increase in the consumption of various food additives in recent years. The purpose of this study was to identify the incidence of sensitization to food additives by using skin prick test in patients with allergy and to determine the concordance rate between positive skin tests and oral challenge in hypersensitivity to additives. This cross-sectional study included 125 (female 71, male 54) patients aged 2-76 years with allergy and 100 healthy individuals. Skin tests were performed in both patient and control groups with 25 fresh food additives. Among patients with allergy, 22.4% showed positive skin test at least to one of the applied materials. Skin test was negative to all tested food additives in control group. Oral food challenge was done in 28 patients with positive skin test, in whom 9 patients showed reaction to culprit (Concordance rate=32.1%). The present study suggested that about one-third of allergic patients with positive reaction to food additives showed positive oral challenge; it may be considered the potential utility of skin test to identify the role of food additives in patients with allergy.

76 FR 5319 - Regulation of Fuel and Fuel Additives: Alternative Test Method for Olefins in Gasoline

Science.gov (United States)

2011-01-31

... Regulation of Fuel and Fuel Additives: Alternative Test Method for Olefins in Gasoline AGENCY: Environmental... gasoline. This proposed rule will provide flexibility to the regulated community by allowing an additional... A. Alternative Test Method for Olefins in Gasoline III. Statutory and Executive Order Reviews A...

A Fully Non-Metallic Gas Turbine Engine Enabled by Additive Manufacturing Part I: System Analysis, Component Identification, Additive Manufacturing, and Testing of Polymer Composites

Science.gov (United States)

Grady, Joseph E.; Haller, William J.; Poinsatte, Philip E.; Halbig, Michael C.; Schnulo, Sydney L.; Singh, Mrityunjay; Weir, Don; Wali, Natalie; Vinup, Michael; Jones, Michael G.;

Announcement effects of convertible bond loans versus warrant-bond loans : An empirical analysis for the Dutch market

NARCIS (Netherlands)

de Roon, F.A.; Veld, C.H.

1995-01-01

This study investigates the announcement effects of offerings of convertible bond loans and warrant-bond loans using data for the Dutch market. Using standard event study methodology it is found that on average stock prices show a positive but insignificant abnormal return for the announcement of a

Application of microCT to the non-destructive testing of an additive manufactured titanium component

Directory of Open Access Journals (Sweden)

Anton du Plessis

2015-11-01

Full Text Available In this paper the application of X-ray microCT to the non-destructive testing of an additive manufactured titanium alloy component of complex geometry is demonstrated. Additive manufacturing of metal components is fast growing and shows great promise, yet these parts may contain defects which affect mechanical properties of the components. In this work a layered form of defect is found by microCT, which would have been very difficult or impossible to detect by other non-destructive testing methods due to the object complexity, defect size and shape and because the pores are entirely contained inside the object and not connected to the surface. Additionally, this test part was subjected to hot isostatic pressing (HIPPING and subsequently scanned. Comparing before and after scans by alignment of the volumes allows visualization and quantification of the pore size changes. The application of X-ray microCT to additive manufacturing is thus demonstrated in this example to be an ideal combination, especially for process improvements and for high value components.

How does additional diagnostic testing influence the initial diagnosis in patients with cognitive complaints in a memory clinic setting?

Science.gov (United States)

Meijs, Anouk P; Claassen, Jurgen A H R; Rikkert, Marcel G M Olde; Schalk, Bianca W M; Meulenbroek, Olga; Kessels, Roy P C; Melis, René J F

2015-01-01

patients suspected of dementia frequently undergo additional diagnostic testing (e.g. brain imaging or neuropsychological assessment) after standard clinical assessment at a memory clinic. This study investigates the use of additional testing in an academic outpatient memory clinic and how it influences the initial diagnosis. the initial diagnosis after standard clinical assessment (history, laboratory tests, cognitive screening and physical and neurological examination) and the final diagnosis after additional testing of 752 memory clinic patients were collected. We specifically registered if, and what type of, additional testing was requested. additional testing was performed in 518 patients (69%), 67% of whom underwent magnetic resonance imaging, 45% had neuropsychological assessment, 14% had cerebrospinal fluid analysis and 49% had (combinations of) other tests. This led to a modification of the initial diagnosis in 17% of the patients. The frequency of change was highest in patients with an initial non-Alzheimer's disease (AD) dementia diagnosis (54%, compared with 11 and 14% in patients with AD and 'no dementia'; P testing 44% was diagnosed with AD, 9% with non-AD dementia and 47% with 'no dementia'. additional testing should especially be considered in non-AD patients. In the large group of patients with an initial AD or 'no dementia' diagnosis, additional tests have little diagnostic impact and may perhaps be used with more restraint. © The Author 2014. Published by Oxford University Press on behalf of the British Geriatrics Society. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Is there a role of food additives in recurrent aphthous stomatitis? A prospective study with patch testing.

Science.gov (United States)

Gülseren, Duygu; Hapa, Asli; Ersoy-Evans, Sibel; Elçin, Gonca; Karaduman, Ayşen

2017-03-01

Recurrent aphthous stomatitis (RAS) is a common disease of the oral mucosa with an unknown etiology. This study aimed to determine if food additives play a role in the etiology of RAS as well as to determine if patch testing can be used to detect which allergens cause RAS. This prospective study included 24 patients with RAS and 22 healthy controls. All the participants underwent patch testing for 23 food additives. In total, 21 (87.5%) RAS patients and 3 (13.6%) controls had positive patch test reactions to ≥1 allergens; the difference in the patch test positivity rate between groups was significant (P food additives might play a role in the etiology of RAS and that patch testing could be a method for determining the etiology of RAS. © 2016 The International Society of Dermatology.

Metrology test object for dimensional verification in additive manufacturing of metals for biomedical applications.

Science.gov (United States)

Teeter, Matthew G; Kopacz, Alexander J; Nikolov, Hristo N; Holdsworth, David W

2015-01-01

Additive manufacturing continues to increase in popularity and is being used in applications such as biomaterial ingrowth that requires sub-millimeter dimensional accuracy. The purpose of this study was to design a metrology test object for determining the capabilities of additive manufacturing systems to produce common objects, with a focus on those relevant to medical applications. The test object was designed with a variety of features of varying dimensions, including holes, cylinders, rectangles, gaps, and lattices. The object was built using selective laser melting, and the produced dimensions were compared to the target dimensions. Location of the test objects on the build plate did not affect dimensions. Features with dimensions less than 0.300 mm did not build or were overbuilt to a minimum of 0.300 mm. The mean difference between target and measured dimensions was less than 0.100 mm in all cases. The test object is applicable to multiple systems and materials, tests the effect of location on the build, uses a minimum of material, and can be measured with a variety of efficient metrology tools (including measuring microscopes and micro-CT). Investigators can use this test object to determine the limits of systems and adjust build parameters to achieve maximum accuracy. © IMechE 2014.

Financial oil derivatives: from options to oil warrants and synthetic oilfields

International Nuclear Information System (INIS)

Trabia, Xavier

1992-01-01

This study aims to shed light on some of the most interesting financial oil derivatives issued so far in order to assess the potential of this new wave of innovative funding instruments. In Part I some theoretical background is provided and applied to the problem of the American futures option. The ''binomial'' model for valuing future option contracts is presented and the most accurate alternatives for pricing American futures options are reviewed. The role of these numerical procedures in valuing more complex options involved in oil warrants is examined. Comments are made on the behaviour of volatility, which stands as a key interface between theory and practice in oil trading on the oil futures market. Part II of the study describes in detail some of the most famous new financial oil derivatives. Some final conclusions are drawn on the potential of oil trusts and synthetic oilfields to be involved in project and general funding in the oil industry. (44 figures, 11 tables, 53 references) (UK)

Placing the pieces: Reconstructing the original property mosaic in a warrant and patent watershed

Science.gov (United States)

Bain, D.J.; Brush, G.S.

2005-01-01

Recent research shows that land use history is an important determinant of current ecosystem function. In the United States, characterization of land use change following European settlement requires reconstruction of the original property mosaic. However, this task is difficult in unsystematically surveyed areas east of the Appalachian Mountains. The Gwynns Falls watershed (Baltimore, MD) was originally surveyed in the 1600-1700s under a system of warrants and patents (commonly known as 'metes and bounds'). A method for the reconstruction and mapping of warrant and patent properties is presented and used to map the original property mosaic in the Gwynns Falls watershed. Using the mapped mosaic, the persistence of properties and property lines in the current Gwynns Falls landscape is considered. The results of this research indicate that as in agricultural areas, the original property lines in the Gwynns Falls watershed are persistent. At the same time, the results suggest that the property mosaic in heavily urbanized/suburbanized areas is generally 'reset.' Further, trends in surveying technique, parcel size, and settlement patterns cause property line density and property shape complexity to increase in the less urbanized upper watershed. The persistence of original patterns may be damping expression of heterogeneity gradients in this urban landscape. This spatial pattern of complexity in the original mosaic is directly opposite of hypothesized patterns of landscape heterogeneity arising from urbanization. The technique reported here and the resulting observations are important for landscape pattern studies in areas settled under unsystematic survey systems, especially the heavily urbanized areas of the eastern United States. ?? 2004 Kluwer Academic Publishers.

Thermal stability and filterability of jet fuels containing PDR additives in small-scale tests and realistic rig simulations

Energy Technology Data Exchange (ETDEWEB)

Bauldreay, J.M.; Clark, R.H.; Heins, R.J. [Shell Research, Ltd., Chester (United Kingdom)

1995-05-01

Specification, small-scale and realistic fuel simulation tests have addressed concerns about the impact of pipeline drag reducer (PDR) flow modifying additives on jet fuel handling and performance. A typical PDR additive tended to block filters which were similar to those used in the specification Jet Fuel Thermal Oxidation Tester (JFTOT) and other thermal stability test apparatus. Blockages reduced flow rates and PDR concentrations downstream of the filters. Consequently two PDR additives (A&B) were tested in JFTOT apparatus without the usual in-line pre-filters as part of a Ministry of Defense (MoD) co-ordinated Round Robin exercise. Some fuel/PDR additive combinations caused decreases in JFTOT breakpoints. Effects were additive- (type, concentration and degree of shear) and fuel-dependent; most failures were caused by filter blockages and not by a failing lacquer rating. In further work at Thornton, the thermal stability characteristics of similar fuel/additive combinations have been examined in non-specification tests. In Flask Oxidation Tests, PDR additives caused no significant increase in the liquid phase oxidation rates of the fuels. Additives were tested in the Single Tube Heat Transfer Rig (STHTR) which duplicates many of the conditions of a heat exchanger element in an engine`s fuel supply system. B produced an average two-fold decrease in thermal stability in a Merox fuel; A had no significant effect. In hydrotreated fuel, B reduced the thermal stability up to five-fold. A had little effect below 205{degrees}C, while at higher temperatures there may have been a marginal improvement in thermal stability. Again, certain jet fuel/PDR combinations were seen to reduce thermal stability.

Effects of increasing the PSA cutoff to perform additional biomarker tests before prostate biopsy.

Science.gov (United States)

Nordström, Tobias; Adolfsson, Jan; Grönberg, Henrik; Eklund, Martin

2017-10-03

Multi-step testing might enhance performance of the prostate cancer diagnostic pipeline. Using PSA >1 ng/ml for first-line risk stratification and the Stockholm 3 Model (S3M) blood-test >10% risk of Gleason Score > 7 prostate cancer to inform biopsy decisions has been suggested. We aimed to determine the effects of changing the PSA cutoff to perform reflex testing with S3M and the subsequent S3M cutoff to recommend prostate biopsy while maintaining the sensitivity to detect Gleason Score ≥ 7 prostate cancer. We used data from the prospective, population-based, paired, diagnostic Stockholm 3 (STHLM3) study with participants invited by date of birth from the Swedish Population Register during 2012-2014. All participants underwent testing with PSA and S3M (a combination of plasma protein biomarkers [PSA, free PSA, intact PSA, hK2, MSMB, MIC1], genetic polymorphisms, and clinical variables [age, family, history, previous prostate biopsy, prostate exam]). Of 47,688 men in the STHLM3 main study, we used data from 3133 men with S3M >10% and prostate biopsy data. Logistic regression models were used to calculate prostate cancer detection rates and proportion saved biopsies. 44.2%, 62.5% and 67.9% of the participants had PSA PSA cut-off for additional work-up from 1 ng/ml to 1.5 ng/ml would thus save 18.3% of the performed tests, 4.9% of the biopsies and 1.3% (10/765) of Gleason Grade ≥ 7 cancers would be un-detected. By lowering the S3M cutoff to recommend biopsy, sensitivity to high-grade prostate cancer can be restored, to the cost of increasing the number of performed biopsies modestly. The sensitivity to detect prostate cancer can be maintained when using different PSA cutoffs to perform additional testing. Biomarker cut-offs have implications on number of tests and prostate biopsies performed. A PSA cutoff of 1.5 ng/ml to perform additional testing such as the S3M test might be considered. ISRCTN84445406 .

Orbital simulation life tests of nickel hydrogen batteries with additional non-eclipse cycles

Science.gov (United States)

Johnson, P. J.; Donley, S. W.; Verrier, D. C.

Nickel-hydrogen battery technology has established itself as the system of choice to provide energy storage on board Earth orbiting satellites. In addition to providing electrical power for the satellite during the periods the satellite's solar arrays are eclipsed by the Earth, applications are evolving (such as ion propulsion) where the battery is required to supplement the power supplied to the spacecraft by the solar panels in order to meet the peak power demands. In this paper, the results of a four-year accelerated life test programme, equivalent to more than 20 years in orbit, are reported. Additional non-eclipse cycles were added to both the eclipse and solstice seasons of each simulated spacecraft year. The results show that the additional discharges do not significantly effect the rates of performance degradation of the batteries.

Application and testing of additive manufacturing for mirrors and precision structures

Science.gov (United States)

Sweeney, Michael; Acreman, Martyn; Vettese, Tom; Myatt, Ray; Thompson, Mike

2015-09-01

Additive Manufacturing (aka AM, and 3-D printing) is widely touted in the media as the foundation for the next industrial revolution. Beneath the hype, AM does indeed offer profound advantages in lead-time, dramatically reduced consumption of expensive raw materials, while enabling new and innovative design forms that cannot be produced by other means. General Dynamics and their industry partners have begun to embrace this technology for mirrors and precision structures used in the aerospace, defense, and precision optical instrumentation industries. Aggressively lightweighted, open and closed back test mirror designs, 75-150 mm in size, were first produced by AM from several different materials. Subsequent optical finishing and test experiments have exceeded expectations for density, surface finish, dimensional stability and isotropy of thermal expansion on the optical scale of measurement. Materials currently under examination include aluminum, titanium, beryllium, aluminum beryllium, Inconel 625, stainless steel/bronze, and PEKK polymer.

76 FR 65382 - Regulation of Fuel and Fuel Additives: Alternative Test Method for Olefins in Gasoline

Science.gov (United States)

2011-10-21

... Regulation of Fuel and Fuel Additives: Alternative Test Method for Olefins in Gasoline AGENCY: Environmental... gasoline. This final rule will provide flexibility to the regulated community by allowing an additional... Method for Olefins in Gasoline III. Statutory and Executive Order Reviews A. Executive Order 12866...

The paced auditory serial addition test for working memory assessment: Psychometric properties

Science.gov (United States)

Nikravesh, Maryam; Jafari, Zahra; Mehrpour, Masoud; Kazemi, Roozbeh; Amiri Shavaki, Younes; Hossienifar, Shamim; Azizi, Mohamad Parsa

2017-01-01

Background: The paced auditory serial addition test (PASAT) was primarily developed to assess the effects of traumatic brain injury on cognitive functioning. Working memory (WM) is one of the most important aspects of cognitive function, and WM impairment is one of the clinically remarkable signs of aphasia. To develop the Persian version of PASAT, an initial version was used in individuals with aphasia (IWA). Methods: In this study, 25 individuals with aphasia (29-60 years) and 85 controls (18-60 years) were included. PASAT was presented in the form of recorded 61 single-digit numbers (1 to 9). The participants repeatedly added the 2 recent digits. The psychometric properties of PASAT including convergent validity (using the digit memory span tasks), divergent validity (using results in the control group and IWA group), and face validity were investigated. Test-retest reliability was considered as well. Results: The relationship between the PASAT and digit memory span tests was moderate to strong in the control group (forward digit memory span test: r= 0.52, p< 0.0001; backward digit memory span test: r = 0.48, p< 0.0001). A strong relationship was found in IWA (forward digit memory span test: r= 0.72, p< 0.0001; backward digit memory span test: r= 0.53, p= 0.006). Also, strong testretest reliability (intraclass correlation= 0.95, p< 0.0001) was observed. Conclusion: According to our results, the PASAT is a valid and reliable test to assess working memory, particularly in IWA. It could be used as a feasible tool for clinical and research applications. PMID:29445690

How does additional diagnostic testing influence the initial diagnosis in patients with cognitive complaints in a memory clinic setting?

NARCIS (Netherlands)

Meijs, A.P.; Claassen, J.A.H.R.; Olde Rikkert, M.G.M.; Schalk, B.W.M; Meulenbroek, O.V.; Kessels, R.P.C.; Melis, R.J.F.

2015-01-01

Background: patients suspected of dementia frequently undergo additional diagnostic testing (e.g. brain imaging or neuropsychological assessment) after standard clinical assessment at a memory clinic. This study investigates the use of additional testing in an academic outpatient memory clinic and

How does additional diagnostic testing influence the initial diagnosis in patients with cognitive complaints in a memory clinic setting?

NARCIS (Netherlands)

Meijs, A.P.; Claassen, J.A.; Olde Rikkert, M.G.M.; Schalk, B.W.M; Meulenbroek, O.V.; Kessels, R.P.C.; Melis, R.J.F.

2015-01-01

BACKGROUND: patients suspected of dementia frequently undergo additional diagnostic testing (e.g. brain imaging or neuropsychological assessment) after standard clinical assessment at a memory clinic. This study investigates the use of additional testing in an academic outpatient memory clinic and

Performance on Paced Auditory Serial Addition Test and cerebral blood flow in multiple sclerosis

NARCIS (Netherlands)

D'haeseleer, M.; Steen, C.; Hoogduin, J. M.; van Osch, M. J. P.; Fierens, Y.; Cambron, M.; Koch, M. W.; De Keyser, J.

BackgroundTo assess the relationship between performance on the Paced Auditory Serial Addition Test (PASAT) and both cerebral blood flow (CBF) and axonal metabolic integrity in normal appearing white matter (NAWM) of the centrum semiovale in patients with multiple sclerosis (MS). MethodsNormal

The nuclear dissuasion without tests

International Nuclear Information System (INIS)

2003-02-01

Since the signature of the french treaty against the nuclear tests (Tice) in 1995, the french engineers must used the simulation to warrant the performance and the safety of weapons. This paper recalls the historical aspects of the french nuclear tests and presents the technological and scientific resources to simulate a nuclear weapon operating. a special interest is given to the computer TERA. (A.L.B.)

Advanced Manufacturing Technologies (AMT): Additive Manufactured Hot Fire Planning and Testing in GRC Cell 32

Data.gov (United States)

National Aeronautics and Space Administration — The objective of this project is to hot fire test an additively manufactured thrust chamber assembly TCA (injector and thrust chamber). GRC will install the...

Formulation and Testing of Paraffin-Based Solid Fuels Containing Energetic Additives for Hybrid Rockets

Science.gov (United States)

Larson, Daniel B.; Boyer, Eric; Wachs,Trevor; Kuo, Kenneth K.; Story, George

2012-01-01

Many approaches have been considered in an effort to improve the regression rate of solid fuels for hybrid rocket applications. One promising method is to use a fuel with a fast burning rate such as paraffin wax; however, additional performance increases to the fuel regression rate are necessary to make the fuel a viable candidate to replace current launch propulsion systems. The addition of energetic and/or nano-sized particles is one way to increase mass-burning rates of the solid fuels and increase the overall performance of the hybrid rocket motor.1,2 Several paraffin-based fuel grains with various energetic additives (e.g., lithium aluminum hydride (LiAlH4) have been cast in an attempt to improve regression rates. There are two major advantages to introducing LiAlH4 additive into the solid fuel matrix: 1) the increased characteristic velocity, 2) decreased dependency of Isp on oxidizer-to-fuel ratio. The testing and characterization of these solid-fuel grains have shown that continued work is necessary to eliminate unburned/unreacted fuel in downstream sections of the test apparatus.3 Changes to the fuel matrix include higher melting point wax and smaller energetic additive particles. The reduction in particle size through various methods can result in more homogeneous grain structure. The higher melting point wax can serve to reduce the melt-layer thickness, allowing the LiAlH4 particles to react closer to the burning surface, thus increasing the heat feedback rate and fuel regression rate. In addition to the formulation of LiAlH4 and paraffin wax solid-fuel grains, liquid additives of triethylaluminum and diisobutylaluminum hydride will be included in this study. Another promising fuel formulation consideration is to incorporate a small percentage of RDX as an additive to paraffin. A novel casting technique will be used by dissolving RDX in a solvent to crystallize the energetic additive. After dissolving the RDX in a solvent chosen for its compatibility

Design and Testing of a Hall Effect Thruster with Additively Manufactured Components

Science.gov (United States)

Hopping, Ethan

The UAH-78AM is a low-power Hall effect thruster developed at the University of Alabama in Huntsville to study the application of low-cost additive manufacturing in the design and fabrication of Hall thrusters. The goal of this project is to assess the feasibility of using unconventional materials to produce a low-cost functioning Hall effect thruster and consider how additive manufacturing can expand the design space and provide other benefits. The thruster features channel walls and a propellant distributor that were manufactured using 3D printing with a variety of materials including ABS, ULTEM, and glazed ceramic. A version of the thruster was tested at NASA Glenn Research Center to obtain performance metrics and to validate the ability of the thruster to produce thrust and sustain a discharge. The design of the thruster and the transient performance measurements are presented here. Measured thrust ranged from 17.2 mN to 30.4 mN over a discharge power of 280 W to 520 W with an anode Isp range of 870 s to 1450 s. Temperature limitations of materials used for the channel walls and propellant distributor limit the ability to run the thruster at thermal steady-state. While the current thruster design is not yet ready for continuous operation, revisions to the device that could enable longer duration tests are discussed.

Carotid sinus hypersensitivity: Entity warrants a caution in the critical care unit

Directory of Open Access Journals (Sweden)

Sugata Dasgupta

2016-01-01

Full Text Available Carotid sinus hypersensitivity (CSH syndrome is an entity caused by an overreaction of the carotid sinus baroreceptors to stimulation. Three subtypes of CSH syndrome are recognized according to the response to carotid sinus massage (CSM: Predominantly cardioinhibitory, predominantly vasodepressor and a mixed subtype. We report here the case of a middle-aged female patient admitted in our critical care unit with respiratory failure requiring mechanical ventilation. There were episodes of severe bradycardia whenever her head was rotated to any side, relieved on neutralizing head position and administering intravenous atropine. CSM revealed she had predominantly cardioinhibitory type of CSH syndrome. A cardioinhibitory form of hypersensitive carotid sinus reflex, which is idiopathic in causation, probably explains the severe bradycardia on head rotation seen in our patient. A heightened awareness of this syndrome is necessary for timely diagnosis and management. CSH syndrome results from an overreaction of the carotid sinus baroreceptors to stimulation, manifesting commonly as bradycardia, hypotension and syncope. It is an entity, which warrants caution during routine critical care practices.

Design, Development and Hotfire Testing of Monolithic Copper and Bimetallic Additively Manufactured Combustion Chambers

Science.gov (United States)

Gradl, Paul; Barnett, Greg; Brandsmeier, Will; Greene, Sandy Elam; Protz, Chris

2016-01-01

NASA and industry partners are working towards fabrication process development to reduce costs and schedules associated with manufacturing liquid rocket engine components with the goal of reducing overall mission costs. One such technique being evaluated is powder-bed fusion or selective laser melting (SLM) otherwise commonly referred to as additive manufacturing. The NASA Low Cost Upper Stage Propulsion (LCUSP) program was designed to develop processes and material characterization for the GRCop-84 copper-alloy commensurate with powder bed additive manufacturing, evaluate bimetallic deposition and complete testing of a full scale combustion chamber. As part of this development, the process has been transferred to industry partners to enable a long-term supply chain of monolithic copper combustion chambers. As a direct spin off of this program, NASA is working with industry partners to further develop the printing process for the GRCop-84 material in addition to the C-18150 (CuCrZr) material. To advance the process further and allow for optimization with multiple materials, NASA is also investigating the feasibility of bimetallic additively manufactured chambers. A 1.2k sized thrust-chamber was designed and developed to compare the printing process of the GRCop-84 and C-18150 SLM materials. A series of similar MCC liners also completed development with an Inconel 625 jacket bonded to the GRcop-84 liner evaluating direct metal deposition (DMD) laser and arc-based techniques. This paper describes the design, development, manufacturing and testing of these combustion chambers and associated lessons learned throughout the design and development process.

Measuring the Effect of Housing Quality Interventions: The Case of the New Zealand "Rental Warrant of Fitness".

Science.gov (United States)

Telfar-Barnard, Lucy; Bennett, Julie; Howden-Chapman, Philippa; Jacobs, David E; Ormandy, David; Cutler-Welsh, Matthew; Preval, Nicholas; Baker, Michael G; Keall, Michael

2017-11-07

In New Zealand, as in many other countries, housing in the private-rental sector is in worse condition than in the owner-occupier housing sector. New Zealand residential buildings have no inspection regime after original construction signoff. Laws and regulations mandating standards for existing residential housing are outdated and spread over a range of instruments. Policies to improve standards in existing housing have been notoriously difficult to implement. In this methods paper, we describe the development and implementation of a rental Warrant of Fitness (WoF) intended to address these problems. Dwellings must pass each of 29 criteria for habitability, insulation, heating, ventilation, safety, amenities, and basic structural soundness to reach the WoF minimum standard. The WoF's development was based on two decades of research on the impact of housing quality on health and wellbeing, and strongly influenced by the UK Housing Health and Safety Rating System and US federal government housing standards. Criteria were field-tested across a range of dwelling types and sizes, cities, and climate zones. The implementation stage of our WoF research consists of a non-random controlled quasi-experimental study in which we work with two city-level local government councils to implement the rental WoF, recruiting adjoining council areas as controls, and measuring changes in health, economic, and social outcomes.

Full recovery of Arundo donax particleboard from swelling test without waterproofing additives

Directory of Open Access Journals (Sweden)

Jose-Antonio Flores-Yepes

2012-11-01

Full Text Available This paper presents the development of particleboard based on common reed, reproducing the industry standard manufacturing process applied to wood chipboard. One of the main properties of the resulting board was its resistance to water, due to the hydrophobic properties of the common reed, despite there being no incorporation of melamine or any other waterproofing additive. The boards that were developed were analyzed using 2 mm and 4 mm sieves for fibre selection, a manufacturing pressure of 3 N/mm2 and 25 N/mm2, and a volume of urea formaldehyde resin content ranging from 5.2% to 13% (8 to 20% liquid format. Standard destructive tests were performed. It was found that under certain applied conditions, namely high pressure and adequate resin proportion (a pressure of over 3 N/mm2 and over 15% liquid resin, Arundo donax L. particleboard demonstrated full recovery from the swelling test. This finding highlights an unmatched property in terms of recovery from the swelling test of the designed board. This property confers a interesting property to be used in high humidity environments without the need for special resin or waterproofing process.

Additional prognostic value of physical examination, exercise testing, and arterial ultrasonography for coronary risk assessment in primary prevention.

Science.gov (United States)

Cournot, Maxime; Taraszkiewicz, Dorota; Cambou, Jean-Pierre; Galinier, Michel; Boccalon, Henri; Hanaire-Broutin, Hélène; Chamontin, Bernard; Carrié, Didier; Ferrières, Jean

2009-11-01

The choice of noninvasive tests used in primary prevention of cardiovascular diseases must be based on medical evidence. The aim of this study was to assess the additional prognostic value, over conventional risk factors, of physical examination, exercise testing, and arterial ultrasonography, in predicting a first coronary event. A prospective cohort study was conducted between 1996 and 2004 (n = 2,709), with follow-up in 2006 (response rate 96.6%). Participants had no history or symptoms of cardiovascular disease and had a standardized physical examination, a cardiac exercise testing, and carotid and femoral ultrasonography at baseline. Incident cases of definite coronary events were recorded during follow-up. Over the Framingham risk score, femoral bruit, positive exercise test, intima-media thickness >0.63 mm, and a femoral plaque provided significant additional information to the prediction model. The addition of the exercise test to the traditional risk factors, then the intima-media thickness and lastly the presence of femoral plaques, produces incremental increases in the area under the receiver operating characteristic curve (0.73-0.78, P = .02) and about a 50% increase in the positive predictive value (15.8%-31.4%), with no effect on the negative predictive value (96.4%-96.9%). Physical examination, exercise testing, and arterial ultrasonography provide incremental information on the risk of coronary event in asymptomatic adults. Exercise testing and femoral ultrasonography also improve the accuracy of the risk stratification.

Carbon dioxide test as an additional clinical measure of treatment response in panic disorder

Directory of Open Access Journals (Sweden)

Valença Alexandre M.

2002-01-01

Full Text Available OBJECTIVE: We aim to determine if a treatment with a dose of clonazepam - 2 mg/day, for 6 weeks, blocks spontaneous panic attacks and the ones induced by the inhalation of 35% carbon dioxide (CO2 in panic disorder (PD patients. The CO2 challenge-test may be a useful addition tool for measuring the pharmacological response during the initial phase (6 weeks in the treatment of PD. METHOD: Eighteen PD patients drug free for a week participated in a carbon dioxide challenge test. Fourteen had a panic attack and were openly treated for a 6-week period with clonazepam. At the end of the 6-week period they were submitted again to the CO2 challenge test. RESULTS: After 6 weeks of treatment with clonazepam, 12 of 14 PD patients (85.7% did not have a panic attack after the CO2 challenge test. Just 2 of 14 patients (14.3% had a panic attack after the CO2 challenge test. Ten of 14 (71.4% PD patients had panic free status after clonazepam treatment. The 2 patients who had a panic attack in the sixth week, after the CO2 test, did not have panic free status after the treatment with clonazepam. CONCLUSION: The CO2-test may be a valid tool for testing and predicting the drug response.

14 CFR 29.927 - Additional tests.

Science.gov (United States)

2010-01-01

... that the rotor drive mechanism is safe, must be performed. (b) If turbine engine torque output to the... engine acceleration rate will require more than 10 seconds), and the time for changing speeds may not be... the flattest pitch for smooth operation. (e) The tests prescribed in paragraphs (b) and (d) of this...

Testing the additive versus the compensatory hypothesis of mortality from ring recovery data using a random effects model

Directory of Open Access Journals (Sweden)

Schaub, M.

2004-06-01

Full Text Available The interaction of an additional source of mortality with the underlying “natural” one strongly affects population dynamics. We propose an alternative way to test between two forms of interaction, total additivity and compensation. In contrast to existing approaches, only ring-recovery data where the cause of death of each recovered individual is known are needed. Cause-specific mortality proportions are estimated based on a multistate capture-recapture model. The hypotheses are tested by inspecting the correlation between the cause-specific mortality proportions. A variance decomposition is performed to obtain a proper estimate of the true process correlation. The estimation of the cause-specific mortality proportions is the most critical part of the approach. It works well if at least one of the two mortality rates varies across time and the two recovery rates are constant across time. We illustrate this methodology by a case study of White Storks Ciconia ciconia where we tested whether mortality induced by power line collision is additive to other forms of mortality.

Measuring the Effect of Housing Quality Interventions: The Case of the New Zealand “Rental Warrant of Fitness”

Science.gov (United States)

Telfar-Barnard, Lucy; Bennett, Julie; Howden-Chapman, Philippa; Jacobs, David E.; Ormandy, David; Cutler-Welsh, Matthew; Preval, Nicholas; Baker, Michael G.; Keall, Michael

2017-01-01

In New Zealand, as in many other countries, housing in the private-rental sector is in worse condition than in the owner-occupier housing sector. New Zealand residential buildings have no inspection regime after original construction signoff. Laws and regulations mandating standards for existing residential housing are outdated and spread over a range of instruments. Policies to improve standards in existing housing have been notoriously difficult to implement. In this methods paper, we describe the development and implementation of a rental Warrant of Fitness (WoF) intended to address these problems. Dwellings must pass each of 29 criteria for habitability, insulation, heating, ventilation, safety, amenities, and basic structural soundness to reach the WoF minimum standard. The WoF’s development was based on two decades of research on the impact of housing quality on health and wellbeing, and strongly influenced by the UK Housing Health and Safety Rating System and US federal government housing standards. Criteria were field-tested across a range of dwelling types and sizes, cities, and climate zones. The implementation stage of our WoF research consists of a non-random controlled quasi-experimental study in which we work with two city-level local government councils to implement the rental WoF, recruiting adjoining council areas as controls, and measuring changes in health, economic, and social outcomes. PMID:29112147

Measuring the Effect of Housing Quality Interventions: The Case of the New Zealand “Rental Warrant of Fitness”

Directory of Open Access Journals (Sweden)

Lucy Telfar-Barnard

2017-11-01

Full Text Available In New Zealand, as in many other countries, housing in the private-rental sector is in worse condition than in the owner-occupier housing sector. New Zealand residential buildings have no inspection regime after original construction signoff. Laws and regulations mandating standards for existing residential housing are outdated and spread over a range of instruments. Policies to improve standards in existing housing have been notoriously difficult to implement. In this methods paper, we describe the development and implementation of a rental Warrant of Fitness (WoF intended to address these problems. Dwellings must pass each of 29 criteria for habitability, insulation, heating, ventilation, safety, amenities, and basic structural soundness to reach the WoF minimum standard. The WoF’s development was based on two decades of research on the impact of housing quality on health and wellbeing, and strongly influenced by the UK Housing Health and Safety Rating System and US federal government housing standards. Criteria were field-tested across a range of dwelling types and sizes, cities, and climate zones. The implementation stage of our WoF research consists of a non-random controlled quasi-experimental study in which we work with two city-level local government councils to implement the rental WoF, recruiting adjoining council areas as controls, and measuring changes in health, economic, and social outcomes.

Additional patient outcomes and pathways in evaluations of testing

NARCIS (Netherlands)

Bossuyt, Patrick M. M.; McCaffery, Kirsten

2009-01-01

Before medical tests are introduced into practice, they should be properly evaluated. Randomized trials and other comprehensive evaluations of tests and test strategies can best be designed based on an understanding of how tests can benefit or harm patients. Tests primarily affect patients' health

Acceptance of Colonoscopy Requires more than Test Tolerance

Directory of Open Access Journals (Sweden)

Amanda Condon

2008-01-01

Full Text Available BACKGROUND: Colon cancer screening, including colonoscopy, lags behind other forms of cancer screening for participation rates. The intrinsic nature of the endoscopic procedure may be an important barrier that limits patients from finding this test acceptable and affects willingness to undergo screening. With colon cancer screening programs emerging in Canada, test characteristics and their impact on acceptance warrant consideration.

Sulfur-free lignins from alkaline pulping tested in mortar for use as mortar additives.

Science.gov (United States)

Nadif, A; Hunkeler, D; Käuper, P

2002-08-01

Sulfur-free lignin, obtained through the acid precipitation of black liquor from the soda pulping process, has been tested as water reducer in mortar. It has also been compared to existing commercial additives such as naphthalene sulfonates and lignosulfonates. The ash content and sugar content of these lignins are low in comparison to lignosulfonates, conferring on them higher purity. A procedure for small scale testing derived from the industrial norms SN-EN196 and ASTM (Designation C230-90) is presented. Specifically, all the sulfur-free lignins tested improved the flow of the mortar. Selected flax lignins performed better than lignosulfonates though still less than naphthalene sulfonates. Furthermore, certain hemp lignins gave comparable results to the lignosulfonates. Overall, the straw lignin prepared herein is comparable in performance to commercially available lignins, such as Organocell, Alcell and Curan 100. The plant from which the lignin was isolated, and the process of the pulp mill are the primary influences on the performance of the lignin.

Testing of WS2 Nanoparticles Functionalized by a Humin-Like Shell as Lubricant Additives

Directory of Open Access Journals (Sweden)

Hagit Sade

2018-01-01

Full Text Available Nanoparticles of transition metal dichalcogenides (TMDC have been known to reduce friction and wear when added to oil-type liquid lubricants. Aggregation limits the ability of the nanoparticles to penetrate into the interface between the two rubbing surfaces—an important factor in friction reduction mechanisms. Doping has been successfully used to reduce agglomeration, but it must be done in the production process of the nanoparticles. The use of surface-functionalized nanoparticles is less common than doping. Nonetheless, it has the potential to reduce agglomeration and thereby improve the reduction of friction and wear. In this study, we present the results of preliminary tribological ball-on-flat tests performed with WS2 nanoparticles functionalized by a humin-like conformal shell, as additives to polyalphaolefin-4 (PAO-4 oil. We tested WS2 inorganic nanotubes (INTs and two grades of inorganic fullerene-like nanoparticles (IFs. The shell/coating was found to improve friction reduction for IFs but not for INTs through better dispersion in the oil. The thicker the coating on the IFs, the less agglomerated they were. Coated industrial-grade IFs were found, by far, to be the best additive for friction reduction. We suggest the combination between reduced agglomeration and poor crystallinity as the reason for this result.

Robust Tests for Additive Gene-Environment Interaction in Case-Control Studies Using Gene-Environment Independence

DEFF Research Database (Denmark)

Liu, Gang; Lee, Seunggeun; Lee, Alice W

2018-01-01

test with case-control data. Our simulation studies suggest that the EB approach uses the gene-environment independence assumption in a data-adaptive way and provides power gain compared to the standard logistic regression analysis and better control of Type I error when compared to the analysis......There have been recent proposals advocating the use of additive gene-environment interaction instead of the widely used multiplicative scale, as a more relevant public health measure. Using gene-environment independence enhances the power for testing multiplicative interaction in case......-control studies. However, under departure from this assumption, substantial bias in the estimates and inflated Type I error in the corresponding tests can occur. This paper extends the empirical Bayes (EB) approach previously developed for multiplicative interaction that trades off between bias and efficiency...

Additional Value of CH4 Measurement in a Combined 13C/H2 Lactose Malabsorption Breath Test: A Retrospective Analysis

Science.gov (United States)

Houben, Els; De Preter, Vicky; Billen, Jaak; Van Ranst, Marc; Verbeke, Kristin

2015-01-01

The lactose hydrogen breath test is a commonly used, non-invasive method for the detection of lactose malabsorption and is based on an abnormal increase in breath hydrogen (H2) excretion after an oral dose of lactose. We use a combined 13C/H2 lactose breath test that measures breath 13CO2 as a measure of lactose digestion in addition to H2 and that has a better sensitivity and specificity than the standard test. The present retrospective study evaluated the results of 1051 13C/H2 lactose breath tests to assess the impact on the diagnostic accuracy of measuring breath CH4 in addition to H2 and 13CO2. Based on the 13C/H2 breath test, 314 patients were diagnosed with lactase deficiency, 138 with lactose malabsorption or small bowel bacterial overgrowth (SIBO), and 599 with normal lactose digestion. Additional measurement of CH4 further improved the accuracy of the test as 16% subjects with normal lactose digestion and no H2-excretion were found to excrete CH4. These subjects should have been classified as subjects with lactose malabsorption or SIBO. In conclusion, measuring CH4-concentrations has an added value to the 13C/H2 breath test to identify methanogenic subjects with lactose malabsorption or SIBO. PMID:26371034

Physical Characteristics, Chemical Composition, Organoleptic Test And The Number Of Microbes In The Biscuits With Addition Of Flour Banana Peels

Science.gov (United States)

Hernawati; Aryani, A.; Shintawati, R.

2017-02-01

The purpose of this study to analyze the physical characteristics, chemical composition and organoleptic test of biscuit flour with the addition of flour banana peel. Materials used are banana peels Kepok. Kepok banana peel has been found to contain high fiber food. Biscuit-making stage includes the formation of cream, adding flour and wheat flour dietary fiber from banana peels to concentrations of 0% as control, 25%, 50% and 75% of 100 grams of wheat flour; mixing; molding; baking in the oven for 20-25 minutes with a temperature of 180°C. Parameters to be measured, namely the physical characteristics include: hardness, softness, consistency, crispness. Furthermore, the biscuits were tested by chemical analysis (proximate). Organoleptic test include: aroma, taste, mouthfeel, aftertaste. Data were analyzed statistically using SAS computing programs. Physical and organoleptic test results biscuits with the addition of flour banana peels has sufficient level of preference between like-liked. Based on the results of the proximate analysis of biscuits with the addition of flour banana peels has generally been in accordance with the National Standards of Indonesia (SNI). Conclusion of the study that the addition of flour banana peels in biscuits has the potential to become functional foods that contain high fiber.

Corrective action investigation plan for Central Nevada Test Area, CAU No. 417

International Nuclear Information System (INIS)

1997-04-01

This Corrective Action Investigation Plan (CAIP) is part of a US Department of Energy (DOE)-funded environmental investigation of the Central Nevada Test Area (CNTA). This CAIP addresses the surface investigation and characterization of 15 identified Corrective Action Sites (CASs). In addition, several other areas of the CNTA project area have surface expressions that may warrant investigation. These suspect areas will be characterized, if necessary, in subsequent CAIPs or addendums to this CAIP prepared to address these sites. This CAIP addresses only the 15 identified CASs as shown in Table 2-1 that are associated with the drilling and construction of a number of testing wells designed as part of an underground nuclear testing program. The purpose of the wells at the time of construction was to provide subsurface access for the emplacement, testing, and post detonation evaluations of underground nuclear devices. If contamination is found at any of the 15-surface CASs, the extent of contamination will be determined in order to develop an appropriate corrective action

Large-Scale Spray Releases: Additional Aerosol Test Results

Energy Technology Data Exchange (ETDEWEB)

Daniel, Richard C.; Gauglitz, Phillip A.; Burns, Carolyn A.; Fountain, Matthew S.; Shimskey, Rick W.; Billing, Justin M.; Bontha, Jagannadha R.; Kurath, Dean E.; Jenks, Jeromy WJ; MacFarlan, Paul J.; Mahoney, Lenna A.

2013-08-01

One of the events postulated in the hazard analysis for the Waste Treatment and Immobilization Plant (WTP) and other U.S. Department of Energy (DOE) nuclear facilities is a breach in process piping that produces aerosols with droplet sizes in the respirable range. The current approach for predicting the size and concentration of aerosols produced in a spray leak event involves extrapolating from correlations reported in the literature. These correlations are based on results obtained from small engineered spray nozzles using pure liquids that behave as a Newtonian fluid. The narrow ranges of physical properties on which the correlations are based do not cover the wide range of slurries and viscous materials that will be processed in the WTP and in processing facilities across the DOE complex. To expand the data set upon which the WTP accident and safety analyses were based, an aerosol spray leak testing program was conducted by Pacific Northwest National Laboratory (PNNL). PNNL’s test program addressed two key technical areas to improve the WTP methodology (Larson and Allen 2010). The first technical area was to quantify the role of slurry particles in small breaches where slurry particles may plug the hole and prevent high-pressure sprays. The results from an effort to address this first technical area can be found in Mahoney et al. (2012a). The second technical area was to determine aerosol droplet size distribution and total droplet volume from prototypic breaches and fluids, including sprays from larger breaches and sprays of slurries for which literature data are mostly absent. To address the second technical area, the testing program collected aerosol generation data at two scales, commonly referred to as small-scale and large-scale testing. The small-scale testing and resultant data are described in Mahoney et al. (2012b), and the large-scale testing and resultant data are presented in Schonewill et al. (2012). In tests at both scales, simulants were used

Development and verification testing of automation and robotics for assembly of space structures

Science.gov (United States)

Rhodes, Marvin D.; Will, Ralph W.; Quach, Cuong C.

1993-01-01

A program was initiated within the past several years to develop operational procedures for automated assembly of truss structures suitable for large-aperture antennas. The assembly operations require the use of a robotic manipulator and are based on the principle of supervised autonomy to minimize crew resources. A hardware testbed was established to support development and evaluation testing. A brute-force automation approach was used to develop the baseline assembly hardware and software techniques. As the system matured and an operation was proven, upgrades were incorprated and assessed against the baseline test results. This paper summarizes the developmental phases of the program, the results of several assembly tests, the current status, and a series of proposed developments for additional hardware and software control capability. No problems that would preclude automated in-space assembly of truss structures have been encountered. The current system was developed at a breadboard level and continued development at an enhanced level is warranted.

A test for judging the presence of additional scatter in a Poisson process

International Nuclear Information System (INIS)

Mueller, J.W.

1978-01-01

The effect of additional scatter on a Poisson process is studied. Possible causes for such fluctuations are insufficient stability of the detection efficiency or of the associated electronics. It is shown with a simple model that the presence of fluctuations results in a characteristic broadening of the counting distribution. Comparison of the observed distribution with the one expected for a Poisson process with the same mean value will show three different regions, each with predictable sign of the deviation; the presence of scatter can thus be decided upon by a sign test. Experimental results are in excellent agreement with this expectation

Graded Cycling Test Combined With the Talk Test Is Responsive in Cardiac Rehabilitation

DEFF Research Database (Denmark)

Nielsen, Susanne Grøn; Vinther, Anders

2016-01-01

PURPOSE: To evaluate clinical assessment outcome of cardiac rehabilitation, a simple and reliable submaximal exercise test, not based on heart rate, is warranted. The Talk Test (TT) has been found to correlate well with the ventilatory threshold, and excellent reliability was observed for TT...... combined with the Graded Cycling Test (GCT-TT) in cardiac patients. The purpose was to investigate responsiveness of GCT-TT in cardiac rehabilitation patients. METHODS: Patients (n = 93) referred to 8 weeks of cardiac rehabilitation were included. Pre- and posttests were performed using GCT-TT. Mean test...... changes in watts (W) were compared with the standard error of measurement (SEM95) for groups and the smallest real difference (SRD) for individuals. Minimal clinically important difference was assessed by comparing patient perceived changes in physical fitness with the test changes. RESULTS...

Food additives: an ethical evaluation.

Science.gov (United States)

Mepham, Ben

2011-01-01

Food additives are an integral part of the modern food system, but opinion polls showing most Europeans have worries about them imply an urgent need for ethical analysis of their use. The existing literature on food ethics, safety assessment and animal testing. Food additives provide certain advantages in terms of many people's lifestyles. There are disagreements about the appropriate application of the precautionary principle and of the value and ethical validity of animal tests in assessing human safety. Most consumers have a poor understanding of the relative benefits and risks of additives, but concerns over food safety and animal testing remain high. Examining the impacts of food additives on consumer sovereignty, consumer health and on animals used in safety testing should allow a more informed debate about their appropriate uses.

Small-Scale Spray Releases: Additional Aerosol Test Results

Energy Technology Data Exchange (ETDEWEB)

Schonewill, Philip P.; Gauglitz, Phillip A.; Kimura, Marcia L.; Brown, G. N.; Mahoney, Lenna A.; Tran, Diana N.; Burns, Carolyn A.; Kurath, Dean E.

2013-08-01

One of the events postulated in the hazard analysis at the Waste Treatment and Immobilization Plant (WTP) and other U.S. Department of Energy (DOE) nuclear facilities is a breach in process piping that produces aerosols with droplet sizes in the respirable range. The current approach for predicting the size and concentration of aerosols produced in a spray leak involves extrapolating from correlations reported in the literature. These correlations are based on results obtained from small engineered spray nozzles using pure liquids with Newtonian fluid behavior. The narrow ranges of physical properties on which the correlations are based do not cover the wide range of slurries and viscous materials that will be processed in the WTP and across processing facilities in the DOE complex. To expand the data set upon which the WTP accident and safety analyses were based, an aerosol spray leak testing program was conducted by Pacific Northwest National Laboratory (PNNL). PNNL’s test program addressed two key technical areas to improve the WTP methodology (Larson and Allen 2010). The first technical area was to quantify the role of slurry particles in small breaches where slurry particles may plug the hole and prevent high-pressure sprays. The results from an effort to address this first technical area can be found in Mahoney et al. (2012a). The second technical area was to determine aerosol droplet size distribution and total droplet volume from prototypic breaches and fluids, including sprays from larger breaches and sprays of slurries for which literature data are largely absent. To address the second technical area, the testing program collected aerosol generation data at two scales, commonly referred to as small-scale and large-scale. The small-scale testing and resultant data are described in Mahoney et al. (2012b) and the large-scale testing and resultant data are presented in Schonewill et al. (2012). In tests at both scales, simulants were used to mimic the

Supra-Additive Interaction of Docosahexaenoic Acid and Naproxen and Gastric Safety on the Formalin Test in Rats.

Science.gov (United States)

Arroyo-Lira, Arlette Guadalupe; Rodríguez-Ramos, Fernando; Ortiz, Mario I; Castañeda-Hernández, Gilberto; Chávez-Piña, Aracely Evangelina

2017-11-01

Preclinical Research The aim of this work was to evaluate the effect of docosahexaenoic acid (DHA) on the pharmacokinetics and pharmacodynamics-nociception-of naproxen in rats, as well as to determine the gastric safety resulting from this combination versus naproxen alone. Female Wistar rats were orally administered DHA, naproxen or the DHA-naproxen mixture at fixed-ratio combination of 1:3. The antinociceptive effect was evaluated using the formalin test. The gastric injury was determined 3 h after naproxen administration. An isobolographic analysis was performed to characterize the antinociceptive interaction between DHA and naproxen. To determine the possibility of pharmacokinetic interactions, the oral bioavailability of naproxen was evaluated in presence and absence of oral DHA. The experimental effective dose ED 30 values (Zexp) were decreased from theoretical additive dose values (Zadd; P supra-additive interaction. The oral administration of DHA increased the pharmacokinetic parameter AUC 0- t of naproxen (P supra-additive antinociceptive effect in the formalin test so that this combination could be useful to management of inflammatory pain. Drug Dev Res 78 : 332-339, 2017. © 2017 Wiley Periodicals, Inc. © 2017 Wiley Periodicals, Inc.

Application of the small punch test to determine the fatigue properties of additive manufactured aerospace alloys

Directory of Open Access Journals (Sweden)

Lancaster Robert

2018-01-01

Full Text Available Additive layer manufacturing (ALM processes are becoming increasingly prevalent in the aerospace industry as design engineers look to profit from the numerous advantages that these advanced techniques can offer. However, given the safety critical nature and arduous operating conditions to which these components will be exposed to whilst in service, it is essential that the mechanical properties of such structures are fully understood. Transient microstructures are a typical characteristic of ALM components and resulting from the thermal cycles that occur during the build operation. Those microstructures make any mechanical assessment an involved procedure when assessing the process variables for any given parameter set. A useful mechanical test technique is small-scale testing, in particular, the small punch (SP test. SP testing is capable of localised sampling of a larger scale component and presents an attractive option to mechanically assess complex parts with representative geometries, that would not be possible using more conventional uniaxial test approaches. This paper will present the recent development of a small-scale testing methodology capable of inducing fatigue damage and a series of novel tests performed on different variants of Ti-6Al-4V.

Should children with a history of anaphylaxis to foods undergo challenge testing?

NARCIS (Netherlands)

Vlieg-Boerstra, B. J.; Duiverman, E. J.; van der Heide, S.; Bijleveld, C. M. A.; Kukler, J.; Dubois, A. E. J.

2008-01-01

Data on the frequency of resolution of anaphylaxis to foods are not available, but such resolution is generally assumed to be rare. To determine whether the frequency of negative challenge tests in children with a history of anaphylaxis to foods is frequent enough to warrant challenge testing to

Promoting HIV risk awareness and testing in Latinos living on the U.S.-Mexico border: the Tú No Me Conoces social marketing campaign.

Science.gov (United States)

Olshefsky, Alisa M; Zive, Michelle M; Scolari, Rosana; Zuñiga, María

2007-10-01

Increased incidence of HIV/AIDS in Latinos warrants effective social marketing messages to promote testing. The Tú No Me Conoces (You Don't Know Me) social marketing campaign promoted awareness of HIV risk and testing in Latinos living on the California-Mexico border. The 8-week campaign included Spanish-language radio, print media, a Web site, and a toll-free HIV-testing referral hotline. We documented an increase in HIV testing at partner clinics; 28% of testers who heard or saw an HIV advertisement specifically identified our campaign. Improved understanding of effective social marketing messages for HIV testing in the growing Latino border population is warranted.

An Analysis Of Tensile Test Results to Assess the Innovation Risk for an Additive Manufacturing Technology

Directory of Open Access Journals (Sweden)

Adamczak Stanisław

2015-03-01

Full Text Available The aim of this study was to assess the innovation risk for an additive manufacturing process. The analysis was based on the results of static tensile tests obtained for specimens made of photocured resin. The assessment involved analyzing the measurement uncertainty by applying the FMEA method. The structure of the causes and effects of the discrepancies was illustrated using the Ishikawa diagram. The risk priority numbers were calculated. The uncertainty of the tensile test measurement was determined for three printing orientations. The results suggest that the material used to fabricate the tensile specimens shows clear anisotropy of the properties in relation to the printing direction.

Cost estimate for a proposed GDF Suez LNG testing program

Energy Technology Data Exchange (ETDEWEB)

Blanchat, Thomas K.; Brady, Patrick Dennis; Jernigan, Dann A.; Luketa, Anay Josephine; Nissen, Mark R.; Lopez, Carlos; Vermillion, Nancy; Hightower, Marion Michael

2014-02-01

At the request of GDF Suez, a Rough Order of Magnitude (ROM) cost estimate was prepared for the design, construction, testing, and data analysis for an experimental series of large-scale (Liquefied Natural Gas) LNG spills on land and water that would result in the largest pool fires and vapor dispersion events ever conducted. Due to the expected cost of this large, multi-year program, the authors utilized Sandia's structured cost estimating methodology. This methodology insures that the efforts identified can be performed for the cost proposed at a plus or minus 30 percent confidence. The scale of the LNG spill, fire, and vapor dispersion tests proposed by GDF could produce hazard distances and testing safety issues that need to be fully explored. Based on our evaluations, Sandia can utilize much of our existing fire testing infrastructure for the large fire tests and some small dispersion tests (with some modifications) in Albuquerque, but we propose to develop a new dispersion testing site at our remote test area in Nevada because of the large hazard distances. While this might impact some testing logistics, the safety aspects warrant this approach. In addition, we have included a proposal to study cryogenic liquid spills on water and subsequent vaporization in the presence of waves. Sandia is working with DOE on applications that provide infrastructure pertinent to wave production. We present an approach to conduct repeatable wave/spill interaction testing that could utilize such infrastructure.

Testing with fragrance mix. Is the addition of sorbitan sesquioleate to the constituents useful?

Science.gov (United States)

Frosch, P J; Pilz, B; Burrows, D; Camarasa, J G; Lachapelle, J M; Lahti, A; Menné, T; Wilkinson, J D

1995-05-01

In a multicentre study, the value of adding sorbitan sesquioleate (SSO) to the constituents of the 8% fragrance mix (FM) was investigated. In 7 centres, 709 consecutive patients were tested with 2 types of FM from different sources, its 8 constituents with 1% SSO, its 8 constituents without SSO, and 20% SSO. 5 patients (0.71%) reacted to the emulsifier SSO itself, read as definitely allergic on day 3/4. 53 patients reacted to either one of the mixes with an allergic type of reaction. When tested with the constituents without SSO, 41.5% showed an allergic reaction versus 54.7% with SSO. If both types of reactions were considered (allergic and irritant) 38.3% of 73 patients showed a positive "breakdown" result without SSO, versus 54.8% with SSO. The differences were statistically significant. Reactivity to FM constituents was changed in a specific pattern by addition of SSO--irritant reactions increased, particularly for cinnamic alcohol, eugenol, geraniol, oak moss and hydroxycitronellal, whereas others showed only a slight change. Allergic reactions were also increased by SSO, but the rank order of the top 3 sensitizers (isoeugenol, oak moss and eugenol) did not change. Cinnamic alcohol was the only constituent with decreased reactivity after addition of SSO. A positive history of fragrance sensitivity (HFS) was clearly associated with a positive allergic reaction to either the mix or 1 of its constituents (51% versus 28.6% with a negative HFS). Irritant reactions were linked to a negative HFS in a high proportion (64.3%).(ABSTRACT TRUNCATED AT 250 WORDS)

Transfer of Training in Simple Addition.

Science.gov (United States)

Chen, Yalin; Campbell, Jamie I D

2017-04-18

In recent years several researchers have proposed that skilled adults may solve single-digit addition problems (e.g. 3 + 1 = 4, 4 + 3 = 7) using a fast counting procedure. Practicing a procedure, often leads to transfer of learning and faster performance of unpracticed items. Such transfer has been demonstrated using a counting-based alphabet arithmetic task (e.g., B + 4 = C D E F) that indicated robust generalization of practice (i.e., RT gains) when untrained transfer problems at test had been implicitly practiced (e.g., practice B + 3, test B + 2 or B + 1). Here we constructed analogous simple addition problems (practice 4 + 3, test 4 + 2 or 4 + 1). In each of three experiments (total n = 108) participants received six practice blocks followed by two test blocks of new problems to examine generalization effects. Practice of addition identity-rule problems (i.e., 0 + N = N) showed complete transfer of RT gains made during practice to unpracticed items at test. In contrast, the addition ties (2 + 2, 3 + 3, etc.) presented large RT costs for unpracticed problems at test, but sped up substantially in the second test block. This pattern is consistent with item-specific strengthening of associative memory. The critical items were small non-tie additions (sum ≤ 10) for which the test problems would be implicitly practiced if counting was employed during practice. In all three experiments (and collectively) there was no evidence of generalization for these items in the first test block, but there was robust speed up when the items were repeated in the second test block. Thus, there was no evidence of the generalization of practice that would be expected if counting procedures mediated our participants' performance on small non-tie addition problems.

Development and Hotfire Testing of Additively Manufactured Copper Combustion Chambers for Liquid Rocket Engine Applications

Science.gov (United States)

Gradl, Paul R.; Greene, Sandy; Protz, Chris

2017-01-01

NASA and industry partners are working towards fabrication process development to reduce costs and schedules associated with manufacturing liquid rocket engine components with the goal of reducing overall mission costs. One such technique being evaluated is powder-bed fusion or selective laser melting (SLM), commonly referred to as additive manufacturing (AM). The NASA Low Cost Upper Stage Propulsion (LCUSP) program was designed to develop processes and material characterization for GRCop-84 (a NASA Glenn Research Center-developed copper, chrome, niobium alloy) commensurate with powder bed AM, evaluate bimetallic deposition, and complete testing of a full scale combustion chamber. As part of this development, the process has been transferred to industry partners to enable a long-term supply chain of monolithic copper combustion chambers. To advance the processes further and allow for optimization with multiple materials, NASA is also investigating the feasibility of bimetallic AM chambers. In addition to the LCUSP program, NASA’s Marshall Space Flight Center (MSFC) has completed a series of development programs and hot-fire tests to demonstrate SLM GRCop-84 and other AM techniques. MSFC’s efforts include a 4,000 pounds-force thrust liquid oxygen/methane (LOX/CH4) combustion chamber. Small thrust chambers for 1,200 pounds-force LOX/hydrogen (H2) applications have also been designed and fabricated with SLM GRCop-84. Similar chambers have also completed development with an Inconel 625 jacket bonded to the GRCop-84 material, evaluating direct metal deposition (DMD) laser- and arc-based techniques. The same technologies for these lower thrust applications are being applied to 25,000-35,000 pounds-force main combustion chamber (MCC) designs. This paper describes the design, development, manufacturing and testing of these numerous combustion chambers, and the associated lessons learned throughout their design and development processes.

Multi-Column Experimental Test Bed for Xe/Kr Separation

International Nuclear Information System (INIS)

Greenhalgh, Mitchell Randy; Garn, Troy Gerry; Welty, Amy Keil; Lyon, Kevin Lawrence; Watson, Tony Leroy

2015-01-01

Previous research studies have shown that INL-developed engineered form sorbents are capable of capturing both Kr and Xe from various composite gas streams. The previous experimental test bed provided single column testing for capacity evaluations over a broad temperature range. To advance research capabilities, the employment of an additional column to study selective capture of target species to provide a defined final gas composition for waste storage was warranted. The second column addition also allows for compositional analyses of the final gas product to provide for final storage determinations. The INL krypton capture system was modified by adding an additional adsorption column in order to create a multi-column test bed. The purpose of this modification was to investigate the separation of xenon from krypton supplied as a mixed gas feed. The extra column was placed in a Stirling Ultra-low Temperature Cooler, capable of controlling temperatures between 190 and 253K. Additional piping and valves were incorporated into the system to allow for a variety of flow path configurations. The new column was filled with the AgZ-PAN sorbent which was utilized as the capture medium for xenon while allowing the krypton to pass through. The xenon-free gas stream was then routed to the cryostat filled with the HZ-PAN sorbent to capture the krypton at 191K. Selectivities of xenon over krypton were determined using the new column to verify the system performance and to establish the operating conditions required for multi-column testing. Results of these evaluations verified that the system was operating as designed and also demonstrated that AgZ-PAN exhibits excellent selectivity for xenon over krypton in air at or near room temperature. Two separation tests were performed utilizing a feed gas consisting of 1000 ppmv xenon and 150 ppmv krypton with the balance being made up of air. The AgZ-PAN temperature was held at 295 or 253K while the HZ-PAN was held at 191K for both

Development and Hot-fire Testing of Additively Manufactured Copper Combustion Chambers for Liquid Rocket Engine Applications

Science.gov (United States)

Gradl, Paul R.; Greene, Sandy Elam; Protz, Christopher S.; Ellis, David L.; Lerch, Bradley A.; Locci, Ivan E.

2017-01-01

NASA and industry partners are working towards fabrication process development to reduce costs and schedules associated with manufacturing liquid rocket engine components with the goal of reducing overall mission costs. One such technique being evaluated is powder-bed fusion or selective laser melting (SLM), commonly referred to as additive manufacturing (AM). The NASA Low Cost Upper Stage Propulsion (LCUSP) program was designed to develop processes and material characterization for GRCop-84 (a NASA Glenn Research Center-developed copper, chrome, niobium alloy) commensurate with powder-bed AM, evaluate bimetallic deposition, and complete testing of a full scale combustion chamber. As part of this development, the process has been transferred to industry partners to enable a long-term supply chain of monolithic copper combustion chambers. To advance the processes further and allow for optimization with multiple materials, NASA is also investigating the feasibility of bimetallic AM chambers. In addition to the LCUSP program, NASA has completed a series of development programs and hot-fire tests to demonstrate SLM GRCop-84 and other AM techniques. NASA's efforts include a 4K lbf thrust liquid oxygen/methane (LOX/CH4) combustion chamber and subscale thrust chambers for 1.2K lbf LOX/hydrogen (H2) applications that have been designed and fabricated with SLM GRCop-84. The same technologies for these lower thrust applications are being applied to 25-35K lbf main combustion chamber (MCC) designs. This paper describes the design, development, manufacturing and testing of these numerous combustion chambers, and the associated lessons learned throughout their design and development processes.

Situational judgment test as an additional tool in a medical admission test: an observational investigation.

Science.gov (United States)

Luschin-Ebengreuth, Marion; Dimai, Hans P; Ithaler, Daniel; Neges, Heide M; Reibnegger, Gilbert

2015-03-14

In the framework of medical university admission procedures the assessment of non-cognitive abilities is increasingly demanded. As tool for assessing personal qualities or the ability to handle theoretical social constructs in complex situations, the Situational Judgment Test (SJT), among other measurement instruments, is discussed in the literature. This study focuses on the development and the results of the SJT as part of the admission test for the study of human medicine and dentistry at one medical university in Austria. Observational investigation focusing on the results of the SJT. 4741 applicants were included in the study. To yield comparable results for the different test parts, "relative scores" for each test part were calculated. Performance differences between women and men in the various test parts are analyzed using effect sizes based on comparison of mean values (Cohen's d). The associations between the relative scores achieved in the various test parts were assessed by computing pairwise linear correlation coefficients between all test parts and visualized by bivariate scatterplots. Among successful candidates, men consistently outperform women. Men perform better in physics and mathematics. Women perform better in the SJT part. The least discriminatory test part was the SJT. A strong correlation between biology and chemistry and moderate correlations between the other test parts except SJT is obvious. The relative scores are not symmetrically distributed. The cognitive loading of the performed SJTs points to the low correlation between the SJTs and cognitive abilities. Adding the SJT part into the admission test, in order to cover more than only knowledge and understanding of natural sciences among the applicants has been quite successful.

Antimicrobial resistance and susceptibility testing of anaerobic bacteria.

Science.gov (United States)

Schuetz, Audrey N

2014-09-01

Infections due to anaerobic bacteria can be severe and life-threatening. Susceptibility testing of anaerobes is not frequently performed in laboratories, but such testing is important to direct appropriate therapy. Anaerobic resistance is increasing globally, and resistance trends vary by geographic region. An overview of a variety of susceptibility testing methods for anaerobes is provided, and the advantages and disadvantages of each method are reviewed. Specific clinical situations warranting anaerobic susceptibility testing are discussed. © The Author 2014. Published by Oxford University Press on behalf of the Infectious Diseases Society of America. All rights reserved. For Permissions, please e-mail: journals.permissions@oup.com.

JV Task 107- Pilot-Scale Emission Control Technology Testing for Constellation Energy

Energy Technology Data Exchange (ETDEWEB)

Michael Jones; Brandon Pavlish; Stephen Sollom; John Kay

2007-06-30

An Indonesian, Colombian, and Russian coal were tested in the Energy & Environmental Research Center's combustion test facility for their performance and an evaluation of mercury release and capture with selected additives in both electrostatic precipitator and baghouse configurations. Sorbents included the carbon-based materials NORIT DARCO Hg, Sorbent Technologies B-PAC and B-PAC LC, STI Rejects provided by Constellation Energy, and Envergex e-Sorb, along with ChemMod's high-temperature additive. Each coal was evaluated over several days and compared. Ash-fouling tests were conducted, and mercury levels were monitored using continuous mercury monitors (CMMs). The Ontario Hydro mercury sampling method was also utilized. The Indonesian coal had the lowest ash content, lowest sulfur content, and lowest energy content of the three coals tested. The Colombian coal had the highest mercury content and did contain a significant level of selenium which can interfere with the ability of a CMM to monitor mercury in the gas stream. All sorbents displayed very favorable results. In most cases, mercury removal greater than 86% could be obtained. The Indonesian coal displayed the best mercury removal with sorbent addition. A maximum removal of 97% was measured with this coal using Envergex's carbon-based sorbent at a rate of 4 lb/Macf across an electrostatic precipitator. The high ash and selenium content of the Colombian coal caused it to be a problematic fuel, and ash plugging of the test furnace was a real concern. Problems with the baghouse module led to limited testing. Results indicated that native capture across the baghouse for each coal type was significant enough not to warrant sorbent addition necessary. The fouling potential was the lowest for the Indonesian coal. Low sulfur content contributes to the poor potential for fouling, as witnessed by the lack of deposits during testing. The Russian and Colombian coals had a much higher potential for fouling

Evaluation of alternative chemical additives for high-level waste vitrification feed preparation processing

International Nuclear Information System (INIS)

Seymour, R.G.

1995-01-01

During the development of the feed processing flowsheet for the Defense Waste Processing Facility (DWPF) at the Savannah River Site (SRS), research had shown that use of formic acid (HCOOH) could accomplish several processing objectives with one chemical addition. These objectives included the decomposition of tetraphenylborate, chemical reduction of mercury, production of acceptable rheological properties in the feed slurry, and controlling the oxidation state of the glass melt pool. However, the DEPF research had not shown that some vitrification slurry feeds had a tendency to evolve hydrogen (H 2 ) and ammonia (NH 3 ) as the result of catalytic decomposition of CHOOH with noble metals (rhodium, ruthenium, palladium) in the feed. Testing conducted at Pacific Northwest Laboratory and later at the Savannah River Technical Center showed that the H 2 and NH 3 could evolve at appreciable rates and quantities. The explosive nature of H 2 and NH 3 (as ammonium nitrate) warranted significant mitigation control and redesign of both facilities. At the time the explosive gas evolution was discovered, the DWPF was already under construction and an immediate hardware fix in tandem with flowsheet changes was necessary. However, the Hanford Waste Vitrification Plant (HWVP) was in the design phase and could afford to take time to investigate flowsheet manipulations that could solve the problem, rather than a hardware fix. Thus, the HWVP began to investigate alternatives to using HCOOH in the vitrification process. This document describes the selection, evaluation criteria, and strategy used to evaluate the performance of the alternative chemical additives to CHOOH. The status of the evaluation is also discussed

Likelihood of myocardial infarction during stroke rehabilitation preceded by cardiovascular screening and an exercise tolerance test: the Locomotor Experience Applied Post-Stroke (LEAPS) trial.

Science.gov (United States)

Nadeau, Stephen E; Rose, Dorian Kay; Dobkin, Bruce; Wu, Samuel S; Dai, Yufeng E; Schofield, Richard; Duncan, Pamela W

2014-12-01

Coronary artery disease is highly prevalent in patients with stroke, but because revascularization does not improve major clinical outcomes in patients with stable coronary artery disease relative to intensive medical therapy, routine evaluation for this disease is not warranted in stroke patients. However, it might be warranted in patients destined to undergo vigorous physical therapy. The Locomotor Experience Applied Post-Stroke study, a randomized controlled trial of 408 participants that tested the relative efficacy of two rehabilitation techniques on functional walking level, provided the opportunity to address this question. The study aims to test the efficacy of screening for cardiovascular disease and an exercise tolerance test in assuring safety among patients undergoing vigorous rehabilitation for gait impairment. All participants were screened for serious cardiovascular and pulmonary conditions. At six-weeks poststroke, they also completed a cardiovascular screening inventory and underwent an exercise tolerance test involving bicycle ergometry. Participants received 36, 90-min sessions of a prescribed physical therapy (three per week), initiated at either two-months or six-months poststroke. Twenty-nine participants were excluded on the basis of the cardiac screening questionnaire, and 15 failed the exercise tolerance test for cardiovascular reasons. No participant experienced a cardiac event during a treatment session. Two participants experienced myocardial infarctions, but continued in the trial. In three additional participants, myocardial infarctions caused or contributed to death. The combination of a negative cardiac screen and the absence of exercise tolerance test failure appeared to have a high negative predictive value for cardiac events during treatment, despite the likelihood of a high prevalence of coronary artery disease in our population. © 2014 World Stroke Organization.

Requirements to be met by recurrent ultrasonic inspection of reactor components using collimator-free testing systems

International Nuclear Information System (INIS)

Csapo, G.; Just, T.

1997-01-01

The paper is intended as an initial contribution to establishing concrete definitions and requirements for digital, collimator-free US testing systems. The objective is to warrant the quality of information derived and reproducibility of test results of recurrent inspections of nuclear components, as well as to achieve a reduction of testing and evaluation time. (orig./CB) [de

DWPF Recycle Evaporator Simulant Tests

International Nuclear Information System (INIS)

Stone, M

2005-01-01

Testing was performed to determine the feasibility and processing characteristics of an evaporation process to reduce the volume of the recycle stream from the Defense Waste Processing Facility (DWPF). The concentrated recycle would be returned to DWPF while the overhead condensate would be transferred to the Effluent Treatment Plant. Various blends of evaporator feed were tested using simulants developed from characterization of actual recycle streams from DWPF and input from DWPF-Engineering. The simulated feed was evaporated in laboratory scale apparatus to target a 30X volume reduction. Condensate and concentrate samples from each run were analyzed and the process characteristics (foaming, scaling, etc) were visually monitored during each run. The following conclusions were made from the testing: Concentration of the ''typical'' recycle stream in DWPF by 30X was feasible. The addition of DWTT recycle streams to the typical recycle stream raises the solids content of the evaporator feed considerably and lowers the amount of concentration that can be achieved. Foaming was noted during all evaporation tests and must be addressed prior to operation of the full-scale evaporator. Tests were conducted that identified Dow Corning 2210 as an antifoam candidate that warrants further evaluation. The condensate has the potential to exceed the ETP WAC for mercury, silicon, and TOC. Controlling the amount of equipment decontamination recycle in the evaporator blend would help meet the TOC limits. The evaporator condensate will be saturated with mercury and elemental mercury will collect in the evaporator condensate collection vessel. No scaling on heating surfaces was noted during the tests, but splatter onto the walls of the evaporation vessels led to a buildup of solids. These solids were difficult to remove with 2M nitric acid. Precipitation of solids was not noted during the testing. Some of the aluminum present in the recycle streams was converted from gibbsite to

Acceptance test report: Field test of mixer pump for 241-AN-107 caustic addition project

International Nuclear Information System (INIS)

Leshikar, G.A.

1997-01-01

The field acceptance test of a 75 HP mixer pump (Hazleton serial number N-20801) installed in Tank 241-AN-107 was conducted from October 1995 thru February 1996. The objectives defined in the acceptance test were successfully met, with two exceptions recorded. The acceptance test encompassed field verification of mixer pump turntable rotation set-up and operation, verification that the pump instrumentation functions within established limits, facilitation of baseline data collection from the mixer pump mounted ultrasonic instrumentation, verification of mixer pump water flush system operation and validation of a procedure for its operation, and several brief test runs (bump) of the mixer pump

The attitudes of Dutch fertility specialists towards the addition of genetic testing in screening of tubal factor infertility.

Science.gov (United States)

Malogajski, Jelena; Jansen, Marleen E; Ouburg, Sander; Ambrosino, Elena; Terwee, Caroline B; Morré, Servaas A

2017-06-01

This study aims to identify elements perceived by Dutch fertility specialists as barriers and facilitators for the introduction of genetic testing, and their attitudes towards the use of genetic information. The genetic test would be implemented in routine screening for tubal pathology and identifies SNPs relevant for the immune response causing tubal pathology. Experienced reproductive specialists working in Dutch Academic Hospitals were interviewed. Based on the results of four interviews a questionnaire was developed and used to survey medical doctors in six out of eight Dutch Academic hospitals. 60.4% (n=91) stated that the addition of genetic markers to the Chlamydia trachomatis antibody test (CAT) in screening for tubal pathology would increase screening accuracy. 68.2% (n=90) agreed they would require additional training on clinical genetics. Clinical utility (91.2%, n=91) and cost-effectiveness (95.6%, n=91) were recognized by the respondents as important factors in gaining support for the new screening strategy. In summary, respondents showed a positive attitude towards the implementation of a genetic test combined with CAT for tubal factor infertility (TFI) screening. To gain their support the majority of respondents agreed that clinical utility, specifically cost-effectiveness, is an important factor. Comprehensive research about economic implications and utility regarding the introduction of genomic markers should be the next step in the implementation strategy. Furthermore, education and training would need to be developed and offered to fertility care professionals about genetic markers, their interpretation, and implications for clinical decision-making. Copyright © 2017 Elsevier B.V. All rights reserved.

First observational tests of eternal inflation.

Science.gov (United States)

Feeney, Stephen M; Johnson, Matthew C; Mortlock, Daniel J; Peiris, Hiranya V

2011-08-12

The eternal inflation scenario predicts that our observable Universe resides inside a single bubble embedded in a vast inflating multiverse. We present the first observational tests of eternal inflation, performing a search for cosmological signatures of collisions with other bubble universes in cosmic microwave background data from the WMAP satellite. We conclude that the WMAP 7-year data do not warrant augmenting the cold dark matter model with a cosmological constant with bubble collisions, constraining the average number of detectable bubble collisions on the full sky N(s) < 1.6 at 68% C.L. Data from the Planck satellite can be used to more definitively test the bubble-collision hypothesis.

Reliability of D-Dimer test results in deciding the necessity of performing CTA in high risk population to establish the diagnosis of PE

Directory of Open Access Journals (Sweden)

Saher Ebrahim Taman

2016-06-01

Conclusion: Negative D-Dimer test is a reliable diagnostic modality to rule out the need for CT Angiography in patients at high risk population of PE. However, positive test results cannot confirm the diagnosis and further testing is warranted.

The Addenbrooke's Cognitive Examination Revised as a potential screening test for elderly drivers.

Science.gov (United States)

Ferreira, Inês S; Simões, Mário R; Marôco, João

2012-11-01

Considerable research has shown that neuropsychological tests are predictive of real-world driving ability. The Mini-Mental State Examination (MMSE) is a brief cognitive test that has been commonly used in the assessment of older drivers. However, this test has inherent problems that limit its validity to evaluate cognitive abilities related to driving and to screen for driving impairments in non-demented people. Therefore, it is useful to test new screening instruments that may predict potential unsafe drivers who require an in-depth neuropsychological assessment in a specialised centre. To date, the utility of the Addenbrooke's Cognitive Examination Revised (ACE-R) as an indicator of driving ability has not been established. In the current study, fifty older drivers (mean age=73.1 years) who were referred for a psychological assessment, the protocol of which included the ACE-R, underwent an on-road driving test. Using linear discriminant analyses, the results highlighted the higher classification accuracy of the ACE-R compared to the MMSE score, particularly for detecting unsafe drivers. Measures of visuospatial and executive functions, which are not incorporated in the MMSE score, had an incremental value in the prediction of driving ability. This emerging brief cognitive test may warrant additional study for use in the fitness to drive assessment of older adults. Copyright © 2012 Elsevier Ltd. All rights reserved.

Additive Manufacturing, Design, Testing, and Fabrication: A Full Engineering Experience at JSC

Science.gov (United States)

Zusack, Steven

2016-01-01

I worked on several projects this term. While most projects involved additive manufacturing, I was also involved with two design projects, two testing projects, and a fabrication project. The primary mentor for these was Richard Hagen. Secondary mentors were Hai Nguyen, Khadijah Shariff, and fabrication training from James Brown. Overall, my experience at JSC has been successful and what I have learned will continue to help me in my engineering education and profession long after I leave. My 3D printing projects ranged from less than a 1 cubic centimeter to about 1 cubic foot and involved several printers using different printing technologies. It was exciting to become familiar with printing technologies such as industrial grade FDM (Fused Deposition Modeling), the relatively new SLA (Stereolithography), and PolyJet. My primary duty with the FDM printers was to model parts that came in from various sources to print effectively and efficiently. Using methods my mentor taught me and the Stratasys Insight software, I was able to minimize imperfections, hasten build time, improve strength for specific forces (tensile, shear, etc...), and reduce likelihood of a print-failure. Also using FDM, I learned how to repair a part after it was printed. This is done by using a special kind of glue that chemically melts the two faces of plastic parts together to form a fused interface. My first goal with SLA technology was to bring the printer back to operational readiness. In becoming familiar with the Pegasus SLA printer, I researched the leveling, laser settings, and different vats to hold liquid material. With this research, I was successfully able to bring the Pegasus back online and have successfully printed multiple sample parts as well as functional parts. My experience with PolyJet technology has been focused on an understanding of the abilities/limits, costs, and the maintenance for daily use. Still upcoming will be experience with using a composite printer that uses FDM

The Development of a Microbial Challenge Test with Acholeplasma laidlawii To Rate Mycoplasma-Retentive Filters by Filter Manufacturers.

Science.gov (United States)

Folmsbee, Martha; Lentine, Kerry Roche; Wright, Christine; Haake, Gerhard; Mcburnie, Leesa; Ashtekar, Dilip; Beck, Brian; Hutchison, Nick; Okhio-Seaman, Laura; Potts, Barbara; Pawar, Vinayak; Windsor, Helena

2014-01-01

Mycoplasma are bacteria that can penetrate 0.2 and 0.22 μm rated sterilizing-grade filters and even some 0.1 μm rated filters. Primary applications for mycoplasma filtration include large scale mammalian and bacterial cell culture media and serum filtration. The Parenteral Drug Association recognized the absence of standard industry test parameters for testing and classifying 0.1 μm rated filters for mycoplasma clearance and formed a task force to formulate consensus test parameters. The task force established some test parameters by common agreement, based upon general industry practices, without the need for additional testing. However, the culture medium and incubation conditions, for generating test mycoplasma cells, varied from filter company to filter company and was recognized as a serious gap by the task force. Standardization of the culture medium and incubation conditions required collaborative testing in both commercial filter company laboratories and in an Independent laboratory (Table I). The use of consensus test parameters will facilitate the ultimate cross-industry goal of standardization of 0.1 μm filter claims for mycoplasma clearance. However, it is still important to recognize filter performance will depend on the actual conditions of use. Therefore end users should consider, using a risk-based approach, whether process-specific evaluation of filter performance may be warranted for their application. Mycoplasma are small bacteria that have the ability to penetrate sterilizing-grade filters. Filtration of large-scale mammalian and bacterial cell culture media is an example of an industry process where effective filtration of mycoplasma is required. The Parenteral Drug Association recognized the absence of industry standard test parameters for evaluating mycoplasma clearance filters by filter manufacturers and formed a task force to formulate such a consensus among manufacturers. The use of standardized test parameters by filter manufacturers

Alternative additives; Alternative additiver

Energy Technology Data Exchange (ETDEWEB)

2007-08-15

In this project a number of industrial and agricultural waste products have been characterised and evaluated in terms of alkali-getter performance. The intended use is for biomass-fired power stations aiming at reducing corrosion or slagging related problems. The following products have been obtained, characterised and evaluated: 1) Brewery draff 2) Danish de-gassed manure 3) Paper sludge 4) Moulding sand 5) Spent bleaching earth 6) Anorthosite 7) Sand 8) Clay-sludge. Most of the above alternative additive candidates are deemed unsuitable due to insufficient chemical effect and/or expensive requirements for pre-treatment (such as drying and transportation). 3 products were selected for full-scale testing: de-gassed manure, spent bleaching earth and clay slugde. The full scale tests were undertaken at the biomass-fired power stations in Koege, Slagelse and Ensted. Spent bleaching earth (SBE) and clay sludge were the only tested additive candidates that had a proven ability to react with KCl, to thereby reduce Cl-concentrations in deposits, and reduce the deposit flux to superheater tubes. Their performance was shown to nearly as good as commercial additives. De-gassed manure, however, did not evaluate positively due to inhibiting effects of Ca in the manure. Furthermore, de-gassed manure has a high concentration of heavy metals, which imposes a financial burden with regard to proper disposal of the ash by-products. Clay-sludge is a wet clay slurring, and drying and transportation of this product entails substantial costs. Spent bleaching does not require much pre-treatment and is therefore the most promising alternative additive. On the other hand, bleaching earth contains residual plant oil which means that a range of legislation relating to waste combustion comes into play. Not least a waste combustion fee of 330 DKK/tonne. For all alternative (and commercial) additives disposal costs of the increase ash by-products represents a significant cost. This is

Letter: California's position on pregnancy testing.

Science.gov (United States)

Cunningham, G C

1976-07-01

The dangers of do-it-yourself pregnancy testing have been recognized in California resulting in the passing of legislation. Pregnancy is a c ondition which requires skill, medical assistance, and occasionally inte rvention or objective counseling. There are 4 arguments against do-it-y ourself testing: 1) it may be inaccurate or inexpertly done, 2) reagents can be hazardous to the health of users or small children, 3) it fails to save money because confirmation by health professionals is usually required, and 4) the individual may not have access to appropriate healt h care resources. California counties have been providing an increasing volume of tests that have served to encourage earlier prenatal care, earlier and safer pregnancy termination, or attendance at family planning clinics. The success of this program warrants implementation by other state governments.

Addition Table of Colours: Additive and Subtractive Mixtures Described Using a Single Reasoning Model

Science.gov (United States)

Mota, A. R.; Lopes dos Santos, J. M. B.

2014-01-01

Students' misconceptions concerning colour phenomena and the apparent complexity of the underlying concepts--due to the different domains of knowledge involved--make its teaching very difficult. We have developed and tested a teaching device, the addition table of colours (ATC), that encompasses additive and subtractive mixtures in a single…

Discrete-Time Pricing and Optimal Exercise of American Perpetual Warrants in the Geometric Random Walk Model

International Nuclear Information System (INIS)

Vanderbei, Robert J.; Pınar, Mustafa Ç.; Bozkaya, Efe B.

2013-01-01

An American option (or, warrant) is the right, but not the obligation, to purchase or sell an underlying equity at any time up to a predetermined expiration date for a predetermined amount. A perpetual American option differs from a plain American option in that it does not expire. In this study, we solve the optimal stopping problem of a perpetual American option (both call and put) in discrete time using linear programming duality. Under the assumption that the underlying stock price follows a discrete time and discrete state Markov process, namely a geometric random walk, we formulate the pricing problem as an infinite dimensional linear programming (LP) problem using the excessive-majorant property of the value function. This formulation allows us to solve complementary slackness conditions in closed-form, revealing an optimal stopping strategy which highlights the set of stock-prices where the option should be exercised. The analysis for the call option reveals that such a critical value exists only in some cases, depending on a combination of state-transition probabilities and the economic discount factor (i.e., the prevailing interest rate) whereas it ceases to be an issue for the put.

Discrete-Time Pricing and Optimal Exercise of American Perpetual Warrants in the Geometric Random Walk Model

Energy Technology Data Exchange (ETDEWEB)

Vanderbei, Robert J., E-mail: rvdb@princeton.edu [Princeton University, Department of Operations Research and Financial Engineering (United States); P Latin-Small-Letter-Dotless-I nar, Mustafa C., E-mail: mustafap@bilkent.edu.tr [Bilkent University, Department of Industrial Engineering (Turkey); Bozkaya, Efe B. [Sabanc Latin-Small-Letter-Dotless-I University, Faculty of Administrative Sciences (Turkey)

2013-02-15

An American option (or, warrant) is the right, but not the obligation, to purchase or sell an underlying equity at any time up to a predetermined expiration date for a predetermined amount. A perpetual American option differs from a plain American option in that it does not expire. In this study, we solve the optimal stopping problem of a perpetual American option (both call and put) in discrete time using linear programming duality. Under the assumption that the underlying stock price follows a discrete time and discrete state Markov process, namely a geometric random walk, we formulate the pricing problem as an infinite dimensional linear programming (LP) problem using the excessive-majorant property of the value function. This formulation allows us to solve complementary slackness conditions in closed-form, revealing an optimal stopping strategy which highlights the set of stock-prices where the option should be exercised. The analysis for the call option reveals that such a critical value exists only in some cases, depending on a combination of state-transition probabilities and the economic discount factor (i.e., the prevailing interest rate) whereas it ceases to be an issue for the put.

21 CFR 25.32 - Foods, food additives, and color additives.

Science.gov (United States)

2010-04-01

... use in food, drugs, devices, or cosmetics. (d) Testing and certification of batches of a color... for humans or animals on FDA's initiative or in response to a petition, under parts 182, 184, 186, or... for humans or animals to use as animal feeds. (i) Approval of a food additive petition or GRAS...

Implementation of the Realized Genomic Relationship Matrix to Open-Pollinated White Spruce Family Testing for Disentangling Additive from Nonadditive Genetic Effects

Directory of Open Access Journals (Sweden)

Omnia Gamal El-Dien

2016-03-01

Full Text Available The open-pollinated (OP family testing combines the simplest known progeny evaluation and quantitative genetics analyses as candidates’ offspring are assumed to represent independent half-sib families. The accuracy of genetic parameter estimates is often questioned as the assumption of “half-sibling” in OP families may often be violated. We compared the pedigree- vs. marker-based genetic models by analysing 22-yr height and 30-yr wood density for 214 white spruce [Picea glauca (Moench Voss] OP families represented by 1694 individuals growing on one site in Quebec, Canada. Assuming half-sibling, the pedigree-based model was limited to estimating the additive genetic variances which, in turn, were grossly overestimated as they were confounded by very minor dominance and major additive-by-additive epistatic genetic variances. In contrast, the implemented genomic pairwise realized relationship models allowed the disentanglement of additive from all nonadditive factors through genetic variance decomposition. The marker-based models produced more realistic narrow-sense heritability estimates and, for the first time, allowed estimating the dominance and epistatic genetic variances from OP testing. In addition, the genomic models showed better prediction accuracies compared to pedigree models and were able to predict individual breeding values for new individuals from untested families, which was not possible using the pedigree-based model. Clearly, the use of marker-based relationship approach is effective in estimating the quantitative genetic parameters of complex traits even under simple and shallow pedigree structure.

Simulation tests for cervical nonorganic signs: a study of face validity.

Science.gov (United States)

Vernon, Howard; Proctor, Dan; Bakalovski, Dianna; Moreton, Jesse

2010-01-01

The purpose of this study was to develop and determine the face validity of additional cervical nonorganic simulation tests. Four simulation tests were either selected from the literature or newly designed: simulated sitting trunk/shoulder rotation (SR; test no. 1), active vs passive cervical rotation (CR; test no. 2), Libman's test (LT; test no. 3) of pressure over the mastoid process, and side-lying passive shoulder abduction (SA; test no. 4). Three groups, 1 without neck pain (n = 44) and 2 with neck pain (n = 43 and 27), were formed. Outcome measures consisted of questions on provocation of pain (Yes/No) and appropriateness (Yes/No) as well as measurements of cervical rotation (goniometric) and pressure pain threshold (pressure algometer). Group test responses were evaluated and scored. A threshold of acceptance was established at 80% agreement for face validity. Ranges of rotation and pressure threshold values were analyzed with the Student t test. In nonneck pain subjects, all 4 tests were rated as nonpainful and 3 were rated as "appropriate" for neck pain examination (not SR). In neck pain subjects, this test and SA were rated as nonpainful, whereas LT was rated as painful in 26% of subjects. Only CR and LT were rated as "appropriate." In neck pain subjects, passive rotations exceeded actives by 10% to 14% (P = .000). On a second round of testing with a slightly modified method, SR and SA achieved acceptable "appropriateness." Once 2 tests were slightly modified, all 4 tests were found to have acceptable face validity. Further research into the reliability of these tests as well as into the combinations of these tests is warranted. Copyright 2010 National University of Health Sciences. Published by Mosby, Inc. All rights reserved.

Study on thermal effects & sulfurized additives, in lubricating greases

Science.gov (United States)

Shah, Ami Atul

Lithium Base grease constitutes about 50% of market. The greases are developed to be able to work in multiple working conditions and have longer working life. Greases with extreme pressure additives and anti-wear additives have been developed as a solution to many of the applications. These developed greases are tested under ASTM D2266 testing conditions to meet the requirements. The actual working conditions, although, differ than the real testing conditions. The loading, speed and temperature conditions can be more harsh, or fluctuating in nature. The cyclic nature of the parameters cannot be directly related to the test performance. For this purpose studies on the performance under spectrum loading, variable speed and fluctuating temperature must be performed. This study includes tests to understand the effect of thermal variation on some of the most commonly used grease additives that perform well under ASTM D2266 testing conditions. The studied additives include most widely used industrial extreme pressure additive MoS2. Performance of ZDDP which is trying to replace MoS2 in its industrial applications has also been studied. The tests cover study of extreme pressure, anti-wear and friction modifier additives to get a general idea on the effects of thermal variation in three areas. Sulphur is the most common extreme pressure additive. Sulphur based MoS 2 is extensively used grease additive. Study to understand the tribological performance of this additive through wear testing and SEM/EDX studies has been done. This performance is also studied for other metallic sulfides like WS2 and sulphur based organic compound. The aim is to study the importance of the type of bond that sulphur shares in its additive's structure on its performance. The MoS2 film formation is found to be on the basis of the FeS formation on the substrate and protection through sacrificial monolayer deposition of the MoS2 sheared structure. The free Mo then tends to oxidise. An attempt to

Cost-effectiveness of a repeat HIV test in pregnancy in India.

Science.gov (United States)

Joshi, Smita; Kulkarni, Vinay; Gangakhedkar, Raman; Mahajan, Uma; Sharma, Sushma; Shirole, Devendra; Chandhiok, Nomita

2015-06-11

To evaluate cost-effectiveness of second HIV test in pregnancy. Current strategy of single HIV test during pregnancy in India can miss new HIV infections acquired after the first test or those HIV infections that were missed in the first test due to a false-negative HIV test. Between August 2011 and April 2013, 9097 pregnant HIV uninfected women were offered a second HIV test near term (34 weeks or beyond) or within 4 weeks of postpartum period. A decision analysis model was used to evaluate cost-effectiveness of a second HIV test in pregnant women near term. Our key outcome measures include programme cost with addition of second HIV test in pregnant women and quality-adjusted life years (QALYs) gained. We detected 4 new HIV infections in the second test. Thus HIV incidence among pregnant women was 0.12 (95% 0.032 to 0.297) per 100 person women years (PWY). Current strategy of a single HIV test is 8.2 times costlier for less QALYs gained as compared to proposed repeat HIV testing of pregnant women who test negative during the first test. Our results warrant consideration at the national level for including a second HIV test of all pregnant women in the national programme. However prior to allocation of resources for a second HIV test in pregnancy, appropriate strategies will have to be planned for improving compliance for prevention of mother-to-child transmission of HIV and reducing loss-to-follow-up of those women detected with HIV. CTRI/2013/12/004183. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://group.bmj.com/group/rights-licensing/permissions.

Septic tank additive impacts on microbial populations.

Science.gov (United States)

Pradhan, S; Hoover, M T; Clark, G H; Gumpertz, M; Wollum, A G; Cobb, C; Strock, J

2008-01-01

Environmental health specialists, other onsite wastewater professionals, scientists, and homeowners have questioned the effectiveness of septic tank additives. This paper describes an independent, third-party, field scale, research study of the effects of three liquid bacterial septic tank additives and a control (no additive) on septic tank microbial populations. Microbial populations were measured quarterly in a field study for 12 months in 48 full-size, functioning septic tanks. Bacterial populations in the 48 septic tanks were statistically analyzed with a mixed linear model. Additive effects were assessed for three septic tank maintenance levels (low, intermediate, and high). Dunnett's t-test for tank bacteria (alpha = .05) indicated that none of the treatments were significantly different, overall, from the control at the statistical level tested. In addition, the additives had no significant effects on septic tank bacterial populations at any of the septic tank maintenance levels. Additional controlled, field-based research iswarranted, however, to address additional additives and experimental conditions.

Matter of 381 Search Warrants Directed to Facebook, 2017 N.Y. Lexis 767, 2; 2017 NY Slip op. 02586, 2 (N.Y. April 4, 2017

Directory of Open Access Journals (Sweden)

Trad. Leopoldo Villar

2017-08-01

Full Text Available The growing importance of electronic communications gives a special interest to its protection, which involves several fundamental rights and guarantees such as freedom, privacy and property. Due to the importance of the discussion and the different positions it reflects on an issue of such sensitivity and pertinence in the world today, we publish below the translation of the decision by the Supreme Court of the State of New York of April 4, 2017, on the 381 search warrants directed to Facebook user accounts, ordered by the same Court in 2013 in response to a request by the New York County District Attorney, supported in turn by an affidavit given by a prosecutor in a criminal investigation. Facebook filed a motion seeking annulment of the search warrants and disclosure of the Prosecutor’s affidavit but both motions were rejected by the Appeals Division, whereupon Facebook appealed to the New York Supreme Court, which dismissed the appeal. Although most agreed that the appeal was not appropriate, the views of the judges contain interpretations that make their reading very useful and particularly the opinión given by the dissenting judge offers enriching arguments for defending the rights of users of electronic services.

Genetic testing for cystic fibrosis in adult patients

Directory of Open Access Journals (Sweden)

Marina Mencinger

2006-02-01

Full Text Available Background: Cystic fibrosis (CF is an autosomal recessive disease caused by mutations in gene encoding cystic fibrosis transmembrane regulator (CFTR protein. Over 1400 mutations found in the gene contribute to the complexity of the CF phenotypes ranging from a classic multiorgan disease commonly involving respiratory, gastrointestinal and reproductive tract to mild and monosymptomatic presentations. Pilocarpine iontophoresis is considered as standard diagnostic test for CF, but it often fails in atypical forms of CF.Methods: In order to provide an additional diagnostic test to assure the diagnosis and provide patients with a proper medical care, we performed a genetic testing on 16 adults suspected to have atypical form of CF. Following counselling, parents of patients with possible homozygote variant of mutations were tested. On a personal request testing was also performed in an adult sibling of a patient with two known mutations to investigate possible carrier hood. The allele specific polymerase chain reaction method (PCR was used to detect 29 most common mutations in the cftr gene.Results: The diagnosis was proved in 3 individuals, a homozygote for Δ F508, and two compound heterozygotes Δ F508/R1162X and Δ F508/3849+10kbC>T. In three cases only one mutation was found: I148T, 2789+5G>A and Δ F508 in a heterozygote form.Conclusions: The genetic testing for CF is a valuable diagnostic tool in atypical forms of CF. Exclusion of possible differential diagnosis is warranted because of a variable CF phenotype. In cases where only one or no mutation was detected a necessity of whole gene sequencing is indicated to exclude rare mutations and polymorphisms that could be implicated in the pathogenesis of atypical CF.

76 FR 16285 - Food Additives Permitted for Direct Addition to Food for Human Consumption; Bacteriophage...

Science.gov (United States)

2011-03-23

... mammalian cells. (See discussion at 71 FR 47729 at 47730). As such, traditional animal testing of the... 51758 at 51759, August 25, 2000). Suitability relates to the effectiveness of the ingredient in... additive be shown to be safe prior to marketing. Under Sec. 170.3(i), a food additive is ``safe'' if...

Stabilization of inorganic mixed waste to pass the TCLP and STLC tests using clay and pH-insensitive additives

Energy Technology Data Exchange (ETDEWEB)

Bowers, J.S.; Anson, J.R.; Painter, S.M. [Lawrence Livermore National Lab., CA (United States)] [and others

1995-12-31

Stabilization is a best demonstrated available technology, or BDAT. This technology traps toxic contaminants in a matrix so that they do not leach into the environment. The stabilization process routinely uses pozzolanic materials. Portland cement, fly ash-lime mixes, gypsum cements, and clays are some of the most common materials. In many instances, materials that can pass the Toxicity Characteristic Leaching Procedure (TCLP the federal leach test) or the Soluble Threshold Leachate Concentration (STLC the California leach test) must have high concentrations of lime or other caustic material because of the low pH of the leaching media. Both leaching media, California`s and EPA`s, have a pH of 5.0. California uses citric acid and sodium citrate while EPA uses acetic acid and sodium acetate. The concentration in the leachate is approximately ten times higher for the STLC procedure than the TCLP. These media can form ligands that provide excellent metal leaching. Because of the aggressive nature of the leaching medium, stabilized wastes in many cases will not pass the leaching tests. At the Lawrence Livermore National Laboratory (LLNL), additives such as dithiocarbamates and thiocarbonates, which are pH-insensitive and provide resistance to ligand formation, are used in the waste stabilization process. Attapulgite, montmorillonite, and sepiolite clays are used because they are forgiving (recipe can be adjusted before the matrix hardens) when formulating a stabilization matrix, and they have a neutral pH. By using these clays and additives, LLNL`s highly concentrated wastewater treatment sludges have passed the TCLP and STLC tests. The most frequently used stabilization process consists of a customized recipe involving waste sludge, clay and dithiocarbamate salt, mixed with a double planetary mixer into a pasty consistency. TCLP and STLC data on this waste matrix have shown that the process matrix meets land disposal requirements.

[The Additional Role of Symptom-Reflux Association Analysis of Diagnosis of Gastroesophageal Reflux Disease Using Bravo Capsule pH Test].

Science.gov (United States)

Jung, Kyoungwon; Park, Moo In; Park, Seun Ja; Moon, Won; Kim, Sung Eun; Kim, Jae Hyun

2017-10-25

Since the development of ambulatory esophageal pH monitoring test to diagnose gastroesophageal reflux disease (GERD), several parameters have been introduced. The aim of this study was to assess whether using the symptom index (SI), symptom sensitivity index (SSI), and symptom association probability (SAP), in addition to the DeMeester score (DS), would be useful for interpreting the Bravo pH monitoring test. A retrospective study, which included 68 patients with reflux symptoms refractory to proton pump inhibitor (PPI) therapy who underwent a Bravo capsule pH test between October 2006 and May 2015, was carried out. Acid reflux parameters and symptom reflux association parameters were analyzed. The median percent time of total pHvariation in percent time of total pHpH test, diagnosis of GERD, including reflux hypersensitivity, can be improved by performing an analysis of the symptom-reflux association and of the day-to-day variation.

Investigation of palm methyl-ester bio-diesel with additive on performance and emission characteristics of a diesel engine under 8-mode testing cycle

Directory of Open Access Journals (Sweden)

S. Senthilkumar

2015-09-01

Full Text Available Biodiesel is receiving increasing attention each passing day because of its same diesel-like fuel properties and compatibility with petroleum-based diesel fueled engines. Therefore, in this paper the prospects and opportunities of using various blends of methyl esters of palm oil as fuel in an engine with and without the effect of multi-functional fuel additive (MFA, Multi DM 32 are studied to arrive at an optimum blend of bio-diesel best suited for low emissions and minimal power drop. Experimental tests were conducted on a four stroke, three cylinder and naturally aspirated D.I. Diesel engine with diesel and various blend percentages of 20%, 40%, 45%, and 50% under the 8 mode testing cycle. The effect of fuel additive was tested out on the optimum blend ratio of the bio-diesel so as to achieve further reduced emissions. Comparison of results shows that, 73% reduction in hydrocarbon emission, 46% reduction in carbon monoxide emission, and around 1% reduction in carbon dioxide emission characteristics. So it is observed that the blend ratio of 40% bio-diesel with MFA fuel additive creates reduced emission and minimal power drop due to effective combustion even when the calorific value is comparatively lower due to its higher cetane number.

Non toxic additives for improved fabric filter performance

Energy Technology Data Exchange (ETDEWEB)

Bustard, C.J.; Baldrey, K.E.; Ebner, T.G. [ADA Technologies, Inc., Englewood, CO (United States)] [and others

1995-11-01

The overall objective of this three-phase Small Business innovative Research (SBIR) program funded by the Department of Energy pittsburgh Energy Technology Center (PETC) is to commercialize a technology based upon the use of non-toxic, novel flue gas conditioning agents to improve particulate air toxic control and overall fabric filter performance. The ultimate objective of the Phase II program currently in progress is to demonstrate that the candidate additives are successful at full-scale on flue gas from a coal-fired utility boiler. This paper covers bench-scale field tests conducted during the period February through May, 1995. The bench-scale additives testing was conducted on a flue gas slipstream taken upstream of the existing particulate control device at a utility power plant firing a Texas lignite coal. These tests were preceded by extensive testing with additives in the laboratory using a simulated flue gas stream and re-dispersed flyash from the same power plant. The bench-scale field testing was undertaken to demonstrate the performance with actual flue gas of the bet candidate additives previously identified in the laboratory. Results from the bench-scale tests will be used to establish operating parameters for a larger-scale demonstration on either a single baghouse compartment or a full baghouse at the same site.

LOCA testing of high burnup PWR fuel in the HBWR. Additional PIE on the cladding of the segment 650-5

Energy Technology Data Exchange (ETDEWEB)

Oberlaender, B.C.; Espeland, M.; Jenssen, H.K.

2008-07-01

IFA-650.5, a test with pre-irradiated fuel in the Halden Project LOCA test series, was conducted on October 23rd, 2006. The fuel rod had been used in a commercial PWR and had a high burnup, 83 MWd/kgU. Experimental arrangements of the fifth test were similar to the preceding LOCA tests. The peak cladding temperature (PCT) level was higher than in the third and fourth tests, 1050 C. A peak temperature close to the target was achieved and cladding burst occurred at approx. 750 C. Within the joint programme framework of the Halden Project PIE was done, consisting of gamma scanning, visual inspection, neutron-radiography, hydrogen analysis and metallography / ceramography. An additional extensive PIE including metallography, hydrogen analysis, and hardness measurements of cross-sections at seven axial elevations was done. It was completed to study the high burnup and LOCA induced effects on the Zr-4 cladding, namely the migration of oxygen into the cladding from the inside surface, the cladding distension, and the burst (author)(tk)

Alternative Testing Strategies for Nanomaterials: State of the Science and Considerations for Risk Analysis.

Science.gov (United States)

Shatkin, J A; Ong, K J

2016-08-01

The rapid growth of the nanotechnology industry has warranted equal progress in the nanotoxicology and risk assessment fields. In vivo models have traditionally been used to determine human and environmental risk for chemicals; however, the use of these tests has limitations, and there are global appeals to develop reliable alternatives to animal testing. Many have investigated the use of alternative (nonanimal) testing methods and strategies have quickly developed and resulted in the generation of large toxicological data sets for numerous nanomaterials (NMs). Due to the novel physicochemical properties of NMs that are related to surface characteristics, the approach toward toxicity test development has distinct considerations from traditional chemicals, bringing new requirements for adapting these approaches for NMs. The methodical development of strategies that combine multiple alternative tests can be useful for predictive NM risk assessment and help screening-level decision making. This article provides an overview of the main developments in alternative methods and strategies for reducing uncertainty in NM risk assessment, including advantages and disadvantages of in vitro, ex vivo, and in silico methods, and examples of existing comprehensive strategies. In addition, knowledge gaps are identified toward improvements for experimental and strategy design, specifically highlighting the need to represent realistic exposure scenarios and to consider NM-specific concerns such as characterization, assay interferences, and standardization. Overall, this article aims to improve the reliability and utility of alternative testing methods and strategies for risk assessment of manufactured NMs. © 2016 Society for Risk Analysis.

Calculations of Edwards' pipe blowdown tests using the code TRAC P1

International Nuclear Information System (INIS)

O'Mahoney, R.

1979-05-01

The paper describes the results obtained using the non-thermal equilibrium LOCA code TRAC-P1 for two of a series of Pipe Blowdown Tests. Comparisons are made with the experimental values and RELAP-UK Mark IV predictions. Some discrepancies between prediction and experiment are observed, and certain aspects of the model are considered to warrant possible further attention. (U.K.)

Test Driven Development of a Parameterized Ice Sheet Component

Science.gov (United States)

Clune, T.

2011-12-01

Test driven development (TDD) is a software development methodology that offers many advantages over traditional approaches including reduced development and maintenance costs, improved reliability, and superior design quality. Although TDD is widely accepted in many software communities, the suitability to scientific software is largely undemonstrated and warrants a degree of skepticism. Indeed, numerical algorithms pose several challenges to unit testing in general, and TDD in particular. Among these challenges are the need to have simple, non-redundant closed-form expressions to compare against the results obtained from the implementation as well as realistic error estimates. The necessity for serial and parallel performance raises additional concerns for many scientific applicaitons. In previous work I demonstrated that TDD performed well for the development of a relatively simple numerical model that simulates the growth of snowflakes, but the results were anecdotal and of limited relevance to far more complex software components typical of climate models. This investigation has now been extended by successfully applying TDD to the implementation of a substantial portion of a new parameterized ice sheet component within a full climate model. After a brief introduction to TDD, I will present techniques that address some of the obstacles encountered with numerical algorithms. I will conclude with some quantitative and qualitative comparisons against climate components developed in a more traditional manner.

Prevalence of Phosphorus-Based Additives in the Australian Food Supply: A Challenge for Dietary Education?

Science.gov (United States)

McCutcheon, Jemma; Campbell, Katrina; Ferguson, Maree; Day, Sarah; Rossi, Megan

2015-09-01

Phosphorus-based food additives may pose a significant risk in chronic kidney disease given the link between hyperphosphatemia and cardiovascular disease. The objective of the study was to determine the prevalence of phosphorus-based food additives in best-selling processed grocery products and to establish how they were reported on food labels. A data set of 3000 best-selling grocery items in Australia across 15 food and beverage categories was obtained for the 12 months ending December 2013 produced by the Nielsen Company's Homescan database. The nutrition labels of the products were reviewed in store for phosphorus additives. The type of additive, total number of additives, and method of reporting (written out in words or as an E number) were recorded. Presence of phosphorus-based food additives, number of phosphorus-based food additives per product, and the reporting method of additives on product ingredient lists. Phosphorus-based additives were identified in 44% of food and beverages reviewed. Additives were particularly common in the categories of small goods (96%), bakery goods (93%), frozen meals (75%), prepared foods (70%), and biscuits (65%). A total of 19 different phosphorus additives were identified across the reviewed products. From the items containing phosphorus additives, there was a median (minimum-maximum) of 2 (1-7) additives per product. Additives by E number (81%) was the most common method of reporting. Phosphorus-based food additives are common in the Australian food supply. This suggests that prioritizing phosphorus additive education may be an important strategy in the dietary management of hyperphosphatemia. Further research to establish a database of food items containing phosphorus-based additives is warranted. Copyright © 2015 National Kidney Foundation, Inc. Published by Elsevier Inc. All rights reserved.

Fuel additive improves plant`s air quality

Energy Technology Data Exchange (ETDEWEB)

Kratch, K.

1995-07-01

Employees of a major pulp and paper manufacturer complained to the Michigan Department of Public Health that emissions from liquefied petroleum gas-powered fork-lifts used in one of the facility`s warehouses were making them ill. The new and tight building was locking in carbon monoxide emissions, according to the plant`s vehicle maintenance supervisor. Although LPG is a clean-burning fuel, it absorbs impurities from pipelines, resulting in emissions problems. After the company introduced a fuel additive to the LPG, employees` symptoms disappeared. According to the maintenance supervisor, there have been no complaints since the additive was introduced five years ago. A major US auto manufacturer also found the additive helpful in reducing carbon monoxide emissions from forklift trucks in a large parts warehouse to levels within OSHA limits. The carmaker conducted a test of 10 forklifts at its Toledo, Ohio, plant to determine the additive`s effectiveness. Trucks were equipped with new or rebuilt vaporizers, and their carburetors were adjusted for the lowest carbon monoxide and hydrocarbon emissions levels prior to the test. According to Advanced Technology, five trucks were filled with LPG and treated with CGX-4, and five used fuel from the same stock but without the additive. All were operated 16 hours a day, six days a week without further tuning or adjusting. Carbon monoxide and hydrocarbon emissions were measured at 30-, 45- and 65-day intervals. Test results show that all of the trucks using the additive maintained low levels of carbon monoxide and hydrocarbon emissions longer than trucks not using the additive.

Drag reduction by natural polymeric additives in PMDS microchannel: Effect of types of additives

OpenAIRE

Ling Fiona W.M.; Abdulbari Hayder A.

2017-01-01

Drag reduction technology was used in medical applications to enhance the blood flow in semiclogged blood streams which can be an alternative treatment for atherosclerosis. In this present study, natural polymeric drag reducing additives (DRA) was introduced to replace synthetic polymer which has the possibility of bringing side effects to human health. Three different sources, namely okra, aloe vera and hibiscus were utilized to extract the natural polymeric additives which were then tested ...

The dilemma of allergy to food additives.

Science.gov (United States)

Bahna, Sami L; Burkhardt, Joshua G

2018-01-01

To provide a brief summary on food additives and to outline a practical approach for evaluating subjects suspected of having reactions to food additives. Information was derived from selected reviews and original articles published in peer-reviewed journals, supplemented by the clinical experience of the authors. Priority was given to studies that used blinded, placebo controlled, oral challenges to confirm adverse reactions to food additives. In addition, selected, appropriately evaluated case reports were included. A large number of food additives are widely used in the food industry. Allergic reactions to additives seem to be rare but are very likely underdiagnosed, primarily due to a low index of suspicion. A wide variety of symptoms to food additives have been reported, but a cause-and-effect relationship has not been well documented in the majority of cases. Reactions to food additives should be suspected in patients who report symptoms related to multiple foods or to a certain food when commercially prepared but not when home made. It is also prudent to investigate food additives in subjects considered to have "idiopathic" reactions. Except for a limited number of natural additives, there is a small role for skin tests or in vitro testing. Oral challenge, in stages, with commonly used additives is the definitive procedure for detecting the offending agent. Once the specific additive is identified, management is strict avoidance, which can be difficult.

Biocompatibility of photopolymers for additive manufacturing

OpenAIRE

Leonhardt Stefan; Klare Martin; Scheer Maurice; Fischer Theresa; Cordes Burghard; Eblenkamp Markus

2016-01-01

To establish photopolymers for the production of class II or class III medical products by additive manufacturing it is essential to know which components of photopolymeric systems, consisting of monomers, photoinitiators and additives, are the determining factors on their biocompatible properties. In this study the leachable substances of a cured photopolymeric system were eluted and identified by HPLC-MS detection. In addition the cured photopolymer was testes for cytotoxicity and genotoxic...

Hydrologic Source Term Processes and Models for the Clearwater and Wineskin Tests, Rainier Mesa, Nevada National Security Site

Energy Technology Data Exchange (ETDEWEB)

Carle, Steven F. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

2011-05-04

This report describes the development, processes, and results of a hydrologic source term (HST) model for the CLEARWATER (U12q) and WINESKIN (U12r) tests located on Rainier Mesa, Nevada National Security Site, Nevada (Figure 1.1). Of the 61 underground tests (involving 62 unique detonations) conducted on Rainier Mesa (Area 12) between 1957 and 1992 (USDOE, 2015), the CLEARWATER and WINESKIN tests present many unique features that warrant a separate HST modeling effort from other Rainier Mesa tests.

Validation of the Arabic Version of the Internet Gaming Disorder-20 Test.

Science.gov (United States)

Hawi, Nazir S; Samaha, Maya

2017-04-01

In recent years, researchers have been trying to shed light on gaming addiction and its association with different psychiatric disorders and psychological determinants. The latest edition version of the American Psychiatric Association's Diagnostic and Statistical Manual of Mental Disorders, Fifth Edition (DSM-5) included in its Section 3 Internet Gaming Disorder (IGD) as a condition for further empirical study and proposed nine criteria for the diagnosis of IGD. The 20-item Internet Gaming Disorder (IGD-20) Test was developed as a valid and reliable tool to assess gaming addiction based on the nine criteria set by the DSM-5. The aim of this study is to validate an Arabic version of the IGD-20 Test. The Arabic version of IGD-20 will not only help in identifying Arabic-speaking pathological gamers but also stimulate cross-cultural studies that could contribute to an area in need of more research for insight and treatment. After a process of translation and back-translation and with the participation of a sizable sample of Arabic-speaking adolescents, the present study conducted a psychometric validation of the IGD-20 Test. Our confirmatory factor analysis showed the validity of the Arabic version of the IGD-20 Test. The one-factor model of the Arabic IGD-20 Test had very good psychometric properties, and it fitted the sample data extremely well. In addition, correlation analysis between the IGD-20 Test and the daily duration on weekdays and weekends gameplay revealed significant positive relationships that warranted a criterion-related validation. Thus, the Arabic version of the IGD-20 Test is a valid and reliable measure of IGD among Arabic-speaking populations.

An initial validation of the Virtual Reality Paced Auditory Serial Addition Test in a college sample.

Science.gov (United States)

Parsons, Thomas D; Courtney, Christopher G

2014-01-30

Numerous studies have demonstrated that the Paced Auditory Serial Addition Test (PASAT) has utility for the detection of cognitive processing deficits. While the PASAT has demonstrated high levels of internal consistency and test-retest reliability, administration of the PASAT has been known to create undue anxiety and frustration in participants. As a result, degradation of performance may be found on the PASAT. The difficult nature of the PASAT may subsequently decrease the probability of their return for follow up testing. This study is a preliminary attempt at assessing the potential of a PASAT embedded in a virtual reality environment. The Virtual Reality PASAT (VR-PASAT) was compared with a paper-and-pencil version of the PASAT as well as other standardized neuropsychological measures. The two modalities of the PASAT were conducted with a sample of 50 healthy university students, between the ages of 19 and 34 years. Equivalent distributions were found for age, gender, education, and computer familiarity. Moderate relationships were found between VR-PASAT and other putative attentional processing measures. The VR-PASAT was unrelated to indices of learning, memory, or visuospatial processing. Comparison of the VR-PASAT with the traditional paper-and-pencil PASAT indicated that both versions require the examinee to sustain attention at an increasingly demanding, externally determined rate. Results offer preliminary support for the construct validity (in a college sample) of the VR-PASAT as an attentional processing measure and suggest that this task may provide some unique information not tapped by traditional attentional processing tasks. Copyright © 2013 Elsevier B.V. All rights reserved.

Nondestructive Testing of Additive Manufactured Metal Parts Used in Aerospace Applications

Science.gov (United States)

Waller, Jess M.

2018-01-01

NDE inspectors, QA/QE professionals, and program managers responsible for the out-sourcing, procurement, fabrication, finishing, inspection, and qualification and certification of additively manufactured (AM) parts should attend this course.

Paced Auditory Serial Addition Test (PASAT 3.0 s): Demographically corrected norms for the Portuguese population.

Science.gov (United States)

Sousa, Claudia Sofia; Neves, Mariana Rigueiro; Passos, Ana Margarida; Ferreira, Aristides; Sá, Maria José

2017-05-23

The main goal of this study was to produce adjusted normative data for the Portuguese population on the Paced Auditory Serial Addition Test (PASAT 3.0 s), the version used in the Brief Repeatable Battery of Neuropsychological Tests developed by the National Multiple Sclerosis Society. The study included 326 community-dwelling individuals (199 women and 127 men) aged between 20 and 70 (mean = 40.33, SD = 14.40), who had educational backgrounds ranging from 4 to 23 years of schooling (mean = 12.28, SD = 4.39). Age, gender and qualifications revealed differences in explaining their performance on the PASAT 3.0 s. Men had significantly better performance on the PASAT 3.0 s than women, even though this represents a small effect size r = 0.18. Demographically corrected normative data was developed and important information regarding performance on the PASAT 3.0 s test is provided. Results are discussed and presented in tables and a formula is presented for computing age, gender and education adjusted T-scores for performance on the PASAT 3.0 s. These results should be considered as useful reference values for clinicians and investigators when applying the PASAT 3.0 s to assess cognitive function like information processing speed in different pathologies.

GENERAL PRINCIPLES OF EU (CRIMINAL LAW: LEGALITY, EQUALITY, NON-DISCRIMINATION, SPECIALTY AND NE BIS IN IDEM IN THE FIELD OF THE EUROPEAN ARREST WARRANT

Directory of Open Access Journals (Sweden)

NOREL NEAGU

2012-05-01

Full Text Available This article deals with the case law of the Court of Justice of the European Union in the field of the European arrest warrant, critically analysing the principles invoked in several decisions validating the European legislation in the field: legality, equality and non-discrimination, specialty, ne bis in idem. The author concludes that an area of freedom, security and justice could be built on these principles, but further harmonisation of legislation needs to be realised to avoid a ”journey to the unknown” for European citizens in respect to legislation of other member states of the EU.

A Randomized Controlled Trial Evaluating Efficacy of Promoting a Home-Based HIV Self-Testing with Online Counseling on Increasing HIV Testing Among Men Who Have Sex with Men.

Science.gov (United States)

Wang, Zixin; Lau, Joseph T F; Ip, Mary; Ho, Shara P Y; Mo, Phoenix K H; Latkin, Carl; Ma, Yee Ling; Kim, Yoona

2018-01-01

We developed an innovative home-based HIV self-testing (HIVST) service that included mailing of a free HIVST kit, and providing online real-time instructions and pre-test/post-test counseling (HIVST-OIC). The present parallel-group and non-blinded randomized controlled trial was conducted to evaluate the efficacy of promoting HIVST-OIC in increasing HIV testing rate among 430 men who have sex with men (MSM), with access to online live-chat applications in Hong Kong. At month 6, as compared to the control group, the intervention group reported significantly higher prevalence of HIV testing of any type (89.8 vs. 50.7%; relative risk (RR): 1.77; p strong potential in increasing prevalence of HIV testing and reducing sexual risk behaviors. Implementation research is warranted.

The additional benefit of the ML Flow test to classify leprosy patients.

Science.gov (United States)

Bührer-Sékula, Samira; Illarramendi, Ximena; Teles, Rose B; Penna, Maria Lucia F; Nery, José Augusto C; Sales, Anna Maria; Oskam, Linda; Sampaio, Elizabeth P; Sarno, Euzenir N

2009-08-01

The use of the skin lesion counting classification leads to both under and over diagnosis of leprosy in many instances. Thus, there is a need to complement this classification with another simple and robust test for use in the field. Data of 202 untreated leprosy patients diagnosed at FIOCRUZ, Rio de Janeiro, Brazil, was analyzed. There were 90 patients classified as PB and 112 classified as MB according to the reference standard. The BI was positive in 111 (55%) patients and the ML Flow test in 116 (57.4%) patients. The ML Flow test was positive in 95 (86%) of the patients with a positive BI. The lesion counting classification was confirmed by both BI and ML Flow tests in 65% of the 92 patients with 5 or fewer lesions, and in 76% of the 110 patients with 6 or more lesions. The combination of skin lesion counting and the ML Flow test results yielded a sensitivity of 85% and a specificity of 87% for MB classification, and correctly classified 86% of the patients when compared to the standard reference. A considerable proportion of the patients (43.5%) with discordant test results in relation to standard classification was in reaction. The use of any classification system has limitations, especially those that oversimplify a complex disease such as leprosy. In the absence of an experienced dermatologist and slit skin smear, the ML Flow test could be used to improve treatment decisions in field conditions.

Ionic Liquids as Novel Lubricants and /or Lubricant Additives

Energy Technology Data Exchange (ETDEWEB)

Qu, J. [ORNL; Viola, M. B. [General Motors Company

2013-10-31

This ORNL-GM CRADA developed ionic liquids (ILs) as novel lubricants or oil additives for engine lubrication. A new group of oil-miscible ILs have been designed and synthesized with high thermal stability, non-corrosiveness, excellent wettability, and most importantly effective anti-scuffing/anti-wear and friction reduction characteristics. Mechanistic analysis attributes the superior lubricating performance of IL additives to their physical and chemical interactions with metallic surfaces. Working with a leading lubricant formulation company, the team has successfully developed a prototype low-viscosity engine oil using a phosphonium-phosphate IL as an anti-wear additive. Tribological bench tests of the IL-additized formulated oil showed 20-33% lower friction in mixed and elastohydrodynamic lubrication and 38-92% lower wear in boundary lubrication when compared with commercial Mobil 1 and Mobil Clean 5W-30 engine oils. High-temperature, high load (HTHL) full-size engine tests confirmed the excellent anti-wear performance for the IL-additized engine oil. Sequence VID engine dynamometer tests demonstrated an improved fuel economy by >2% for this IL-additized engine oil benchmarked against the Mobil 1 5W-30 oil. In addition, accelerated catalyst aging tests suggest that the IL additive may potentially have less adverse impact on three-way catalysts compared to the conventional ZDDP. Follow-on research is needed for further development and optimization of IL chemistry and oil formulation to fully meet ILSAC GF-5 specifications and further enhance the automotive engine efficiency and durability.

Predictive factors warrant screening for obstructive sleep apnea in COPD: a Taiwan National Survey

Directory of Open Access Journals (Sweden)

Hang LW

2016-03-01

questionnaire to assess COPD symptoms and OSA risk, comorbidities, and performance of daily activities. Data from COPD cohorts with and without risk of OSA were analyzed and compared. Results: Of 6,600 interviews completed, 404 subjects fit the epidemiological case definition of COPD – an overall prevalence of 6.1% in this national sample. Data on OSA risk were available for 292 of this COPD cohort, of whom 29.5% were at risk of OSA. Compared to those without risk of OSA, those with risk of OSA were significantly more likely to have hypertension or cardiovascular disease and diabetes, had significantly higher body mass index and COPD Assessment Test scores, and reported impaired work performance and leisure activities. Conclusion: Among adults in Taiwan who fulfill epidemiologic criteria for COPD, 29.5% have coexisting risk of OSA. Comorbid hypertension or cardiovascular disease and diabetes are common and significantly more prevalent among the COPD population at risk of OSA than those who are not. OSA screening is warranted in patients with COPD with those risk factors that are more prevalent in COPD with risk of OSA than without, to target early interventions to reduce adverse cardiovascular sequelae from overlap syndrome. Keywords: cardiovascular risk, COPD, coexistent, obstructive sleep apnea, OSA, overlap syndrome

Rôle des additifs anti-usure des huiles lubrifiantes dans un teste de frottement simulant le contact segment-chemise Role of Antiwear Additives for Lube Oils in a Friction Test Simulating Ring-Liner Contact

Directory of Open Access Journals (Sweden)

Martin J. M.

2006-11-01

Full Text Available Nous avons mis en oeuvre un test de frottement dans lequel les conditions tribologiques sont voisines de celles existant au niveau segment-chemise des moteurs à explosion. Nous avons éprouvé différentes huiles commerciales ainsi que des additifs purs. Ayant choisi la température comme paramètre variable au cours de ce test nous pouvons déterminer pour chaque lubrifiant une plage de température correspondant à une zone d'efficacité maximale de l'additif anti-usure qu'il contient. La température correspondant à la limite inférieure de cette plage est liée à la nature chimique de l'additif. De plus lorsqu'un gradient de température existe entre les deux pièces en frottement, on observe, dans la zone d'efficacité maximale du lubrifiant, un phénomène de pulsations verticales de la goutte d'huile placée dans le contact. Des éléments d'interprétation, expliquant ces deux phénomènes, sont proposés et conduisent à relier l'efficacité anti-usure d'un additif à ses propriétés d'adsorption à la surface des pièces frottantes. The tribological conditions in the test used were similar to these existing in the ringliner area. of explosion engines. Different commercial cils were tested along with pure additives. Since temperature was chosen as a variable parameter during these tests, it was possible to determine a temperature range for each lubricant, corresponding to the maximum efficiency zone for the antiwear additive it contained. The temperature corresponding to the lower limit of this range is linked to the chemical nature of the additive. Likewise, when a temperature gradient exists between two rubbing parts, a vertical pulsation phenomenon of the drop of cil n the contact area occurs in the maximum efficiency zone of the lubricant. Interpretation elements explaining these two phenomena are proposed and lead to linking the antiwear efficiency of an additive to its adsorption properties on the surface of rubbing parts.

Douglas-fir plantations in Europe: a retrospective test of assisted migration to address climate change.

Science.gov (United States)

Isaac-Renton, Miriam G; Roberts, David R; Hamann, Andreas; Spiecker, Heinrich

2014-08-01

We evaluate genetic test plantations of North American Douglas-fir provenances in Europe to quantify how tree populations respond when subjected to climate regime shifts, and we examined whether bioclimate envelope models developed for North America to guide assisted migration under climate change can retrospectively predict the success of these provenance transfers to Europe. The meta-analysis is based on long-term growth data of 2800 provenances transferred to 120 European test sites. The model was generally well suited to predict the best performing provenances along north-south gradients in Western Europe, but failed to predict superior performance of coastal North American populations under continental climate conditions in Eastern Europe. However, model projections appear appropriate when considering additional information regarding adaptation of Douglas-fir provenances to withstand frost and drought, even though the model partially fails in a validation against growth traits alone. We conclude by applying the partially validated model to climate change scenarios for Europe, demonstrating that climate trends observed over the last three decades warrant changes to current use of Douglas-fir provenances in plantation forestry throughout Western and Central Europe. © 2014 John Wiley & Sons Ltd.

Acceptability of woman-delivered HIV self-testing to the male partner, and additional interventions: a qualitative study of antenatal care participants in Malawi.

Science.gov (United States)

Choko, Augustine Talumba; Kumwenda, Moses Kelly; Johnson, Cheryl Case; Sakala, Doreen Wongera; Chikalipo, Maria Chifuniro; Fielding, Katherine; Chikovore, Jeremiah; Desmond, Nicola; Corbett, Elizabeth Lucy

2017-06-26

In the era of ambitious HIV targets, novel HIV testing models are required for hard-to-reach groups such as men, who remain underserved by existing services. Pregnancy presents a unique opportunity for partners to test for HIV, as many pregnant women will attend antenatal care (ANC). We describe the views of pregnant women and their male partners on HIV self-test kits that are woman-delivered, alone or with an additional intervention. A formative qualitative study to inform the design of a multi-arm multi-stage cluster-randomized trial, comprised of six focus group discussions and 20 in-depth interviews, was conducted. ANC attendees were purposively sampled on the day of initial clinic visit, while men were recruited after obtaining their contact information from their female partners. Data were analysed using content analysis, and our interpretation is hypothetical as participants were not offered self-test kits. Providing HIV self-test kits to pregnant women to deliver to their male partners was highly acceptable to both women and men. Men preferred this approach compared with standard facility-based testing, as self-testing fits into their lifestyles which were characterized by extreme day-to-day economic pressures, including the need to raise money for food for their household daily. Men and women emphasized the need for careful communication before and after collection of the self-test kits in order to minimize the potential for intimate partner violence although physical violence was perceived as less likely to occur. Most men stated a preference to first self-test alone, followed by testing as a couple. Regarding interventions for optimizing linkage following self-testing, both men and women felt that a fixed financial incentive of approximately USD$2 would increase linkage. However, there were concerns that financial incentives of greater value may lead to multiple pregnancies and lack of child spacing. In this low-income setting, a lottery incentive was

A qualitative study exploring factors associated with Pap test use among North Korean refugees.

Science.gov (United States)

Kim, Kyounghae; Kim, Soohyun; Chung, Yoonkyung

2017-10-01

Lack of medical care in North Korea and vulnerability to human trafficking during their migration increase risks of cervical cancer among North Korean refugees. To better understand factors influencing Pap test use, we conducted a qualitative study of eight North Korean refugees in South Korea. Individual barriers were limited knowledge, lack of perceived need for preventive services, and concerns about costs. Environmental facilitators included having female providers, receiving family support, and free screenings. Refugees' health outlook, including viewing cancers as fatal diseases, hindered seeking Pap tests. Multi-faceted approaches to address individual and environmental factors in promoting Pap tests are warranted.

The repellency of lemongrass oil against stable flies, tested using video tracking

Science.gov (United States)

Baldacchino, Frédéric; Tramut, Coline; Salem, Ali; Liénard, Emmanuel; Delétré, Emilie; Franc, Michel; Martin, Thibaud; Duvallet, Gérard; Jay-Robert, Pierre

2013-01-01

Lemongrass oil (Cymbopogon citratus) is an effective repellent against mosquitoes (Diptera: Culicidae) and house flies (Diptera: Muscidae). In this study, its effectiveness was assessed on stable flies (Diptera: Muscidae) in laboratory conditions. First, we demonstrated that lemongrass oil is an active substance for antennal olfactory receptor cells of Stomoxys calcitrans as indicated by a significant increase in the electroantennogram responses to increasing doses of lemongrass oil. Feeding-choice tests in a flight cage with stable flies having access to two blood-soaked sanitary pads, one of which was treated with lemongrass oil, showed that stable flies (n = 24) spent significantly more time in the untreated zone (median value = 218.4 s) than in the treated zone (median value = 63.7 s). No stable flies fed on the treated pad, whereas nine fed on the untreated pad. These results suggest that lemongrass oil could be used as an effective repellent against stable flies. Additional studies to confirm its spatial repellent and feeding deterrent effects are warranted. PMID:23759542

Materials Testing and Cost Modeling for Composite Parts Through Additive Manufacturing

Science.gov (United States)

2016-04-30

FDM include plastic jet printing (PJP), fused filament modeling ( FFM ), and fused filament fabrication (FFF). FFF was coined by the RepRap project to...additive manufacturing processes? • Fused deposition modeling (FDM) trademarked by Stratasys • Fused filament modeling ( FFM ) and fused filament

Aminodisulfides as additives to lubricants

Energy Technology Data Exchange (ETDEWEB)

Balin, A.I.; Tarasevich, V.B.; Veretenova, T.N.

1980-01-01

A study was carried out and tehcnology developed for producing sulfur-nitrogen containing additives of the type of aminodisulfide by interaction of beta, beta-dichlordialkyl (aryl) disulfides with diethanolamine in a medium of sulfur-diethanolamine. The 2,2'-bis-(diethanol)-dialkyl(aryl) disulfides obtained do not hydrolyze in aqueous soltuions of alkalis, exhibit rather high antiscoring properties and are recommended for tests as active additives of high pressure to SOZH and technological lubricants of the oil and emulsion types.

Functional and community-level soil microbial responses to zinc addition may depend on test system biocomplexity.

Science.gov (United States)

Sverdrup, Line E; Linjordet, Roar; Strømman, Gjermund; Hagen, Snorre B; van Gestel, Cornelis A M; Frostegård, Sa; Sørheim, Roald

2006-12-01

The effect of zinc on soil nitrification and composition of the microbial community in soil was investigated using a full factorial experiment with five zinc concentrations and four levels of biological complexity (microbes only, microbes and earthworms (Eisenia fetida), microbes and Italian ryegrass (Lolium multiflorum var. Macho), and microbes, ryegrass and earthworms). After 6 weeks of exposure, the activity of soil nitrifying bacteria was measured and the microbial community structure was characterized by phospholipid fatty acid (PLFA) analysis. Soil nitrification and several PLFA markers were significantly influenced by either zinc addition and/or the presence of earthworms or ryegrass, and one of the most pronounced changes was the increase of fungi and decrease of bacteria with increasing concentrations of zinc. Of particular interest, however, was the potential interaction between the presence of plants and/or earthworms and the effect of zinc, which the factorial study design allowed us to explore. Such an effect was observed in two cases: Earthworms reduced the positive effect of zinc on the fungal biomass (ANOVA, p=0.03), and the effect of earthworms on the soil nitrification activity depended on zinc concentration (ANOVA, p<0.05). The effect of earthworm presence was not very large, but it does show that multispecies tests might give information about metal toxicity or bioavailability that cannot be predicted from single-species tests.

Assessment of diurnal systemic dose of agrochemicals in regulatory toxicity testing--an integrated approach without additional animal use.

Science.gov (United States)

Saghir, Shakil A; Bartels, Michael J; Rick, David L; McCoy, Alene T; Rasoulpour, Reza J; Ellis-Hutchings, Robert G; Sue Marty, M; Terry, Claire; Bailey, Jason P; Billington, Richard; Bus, James S

2012-07-01

Integrated toxicokinetics (TK) data provide information on the rate, extent and duration of systemic exposure across doses, species, strains, gender, and life stages within a toxicology program. While routine for pharmaceuticals, TK assessments of non-pharmaceuticals are still relatively rare, and have never before been included in a full range of guideline studies for a new agrochemical. In order to better understand the relationship between diurnal systemic dose (AUC(24h)) and toxicity of agrochemicals, TK analyses in the study animals is now included in all short- (excluding acute), medium- and long-term guideline mammalian toxicity studies including reproduction/developmental tests. This paper describes a detailed procedure for the implementation of TK in short-, medium- and long-term regulatory toxicity studies, without the use of satellite animals, conducted on three agrochemicals (X11422208, 2,4-D and X574175). In these studies, kinetically-derived maximum doses (KMD) from short-term studies instead of, or along with, maximum tolerated doses (MTD) were used for the selection of the high dose in subsequent longer-term studies. In addition to leveraging TK data to guide dose level selection, the integrated program was also used to select the most appropriate method of oral administration (i.e., gavage versus dietary) of test materials for rat and rabbit developmental toxicity studies. The integrated TK data obtained across toxicity studies (without the use of additional/satellite animals) provided data critical to understanding differences in response across doses, species, strains, sexes, and life stages. Such data should also be useful in mode of action studies and to improve human risk assessments. Copyright © 2012 Elsevier Inc. All rights reserved.

The Predominance Of Integrative Tests Over Discrete Point Tests In Evaluating The Medical Students' General English Knowledge

Directory of Open Access Journals (Sweden)

maryam Heydarpour Meymeh

2009-03-01

Full Text Available Background and purpose: Multiple choice tests are the most common type of tests used in evaluating the general English knowledge of the students in most medical universities, however the efficacy of these tests are not examined precisely. Wecompare and examine the integrative tests and discrete point tests as measures of the English language knowledge of medical students.Methods: Three tests were given to 60 undergraduate physiotherapy and Audiology students in their second year of study (after passing their general English course. They were divided into 2 groups.The first test for both groups was an integrative test, writing. The second test was a multiple - choice test 0.(prepositions for group one and a multiple - choice test of tensesfor group two. The same items which were mostfi-equently used wrongly in thefirst test were used in the items of the second test. A third test, a TOEFL, was given to the subjects in order to estimate the correlation between this test and tests one and two.Results: The students performed better in the second test, discrete point test rather than the first which was an integrative test. The same grammatical mistakes in the composition were used correctly in the multiple choice tests by the students.Conclusion:Our findings show that student perform better in non-productive rather than productive test. Since being competent English language user is an expected outcome of university language courses it seems warranted to switch to integrative tests as a measure of English language competency.Keywords: INTEGRATIVE TESTS, ENGLISH LANGUAGE FOR MEDICINE, ACADEMIC ENGLISH

Bringing testing to the people - benefits of mobile unit HIV/syphilis testing in Lima, Peru, 2007-2009.

Science.gov (United States)

Lipsitz, Mindy C; Segura, Eddy R; Castro, José Luis; Smith, Edward; Medrano, Carlos; Clark, Jesse L; Lake, Jordan E; Cabello, Robinson

2014-04-01

Mobile unit (MU) HIV testing is an alternative method of providing healthcare access. We compared demographic and behavioural characteristics, HIV testing history and HIV prevalence between participants seeking testing at a MU vs. fixed clinic (FC) in Lima, Peru. Our analysis included men and transgender women (TW) in Lima aged ≥ 18 years old seeking HIV testing at their first visit to a community-based MU or FC from October 2007 to November 2009. HIV testing history, HIV serostatus and behavioural characteristics were analysed. A large percentage of MU attendees self-identified as transgender (13%) or heterosexual (41%). MU attendees were more likely to engage in transactional sex (24% MU vs. 10% FC, p < 0.001), use alcohol/drugs during their last sexual encounter (24% MU vs. 20% FC, p < 0.01) and/or be a first-time HIV tester (48% MU vs. 41% FC, p < 0.001). MU HIV prevalence was 9% overall and 5% among first-time testers (49% in TW and 11% in men who have sex with men [MSM] first-time testers). MU testing reached large numbers of at-risk (MSM/TW) populations engaged in unsafe sexual behaviours, making MU outreach a worthy complement to FC testing. Investigation into whether MU attendees would otherwise access HIV testing is warranted to determine the impact of MU testing.

Preliminary in Vivo Evaluation of a Hybrid Armored Vascular Graft Combining Electrospinning and Additive Manufacturing Techniques

Directory of Open Access Journals (Sweden)

Cristiano Spadaccio

2016-01-01

Full Text Available In this study, we tested in vivo effectiveness of a previously developed poly-L-lactide/poly-8-caprolactone armored vascular graft releasing heparin. This bioprosthesis was designed in order to overcome the main drawbacks of tissue-engineered vascular grafts, mainly concerning poor mechanical properties, thrombogenicity, and endothelialization. The bioprosthesis was successfully implanted in an aortic vascular reconstruction model in rabbits. All grafts implanted were patent at four weeks postoperatively and have been adequately populated by endogenous cells without signs of thrombosis or structural failure and with no need of antiplatelet therapy. The results of this preliminary study might warrant for further larger controlled in vivo studies to further confirm these findings.

Adult-onset offenders: Is a tailored theory warranted?

Science.gov (United States)

Beckley, Amber L.; Caspi, Avshalom; Harrington, Honalee; Houts, Renate M.; Mcgee, Tara Renae; Morgan, Nick; Schroeder, Felix; Ramrakha, Sandhya; Poulton, Richie; Moffitt, Terrie E.

2016-01-01

Purpose To describe official adult-onset offenders, investigate their antisocial histories and test hypotheses about their origins. Methods We defined adult-onset offenders among 931 Dunedin Study members followed to age 38, using criminal-court conviction records. Results Official adult-onset offenders were 14% of men, and 32% of convicted men, but accounted for only 15% of convictions. As anticipated by developmental theories emphasizing early-life influences on crime, adult-onset offenders’ histories of antisocial behavior spanned back to childhood. Relative to juvenile-offenders, during adolescence they had fewer delinquent peers and were more socially inhibited, which may have protected them from conviction. As anticipated by theories emphasizing the importance of situational influences on offending, adult-onset offenders, relative to non-offenders, during adulthood more often had schizophrenia, bipolar disorder, and alcohol-dependence, had weaker social bonds, anticipated fewer informal sanctions, and self-reported more offenses. Contrary to some expectations, adult-onset offenders did not have high IQ or high socioeconomic-status families protecting them from juvenile conviction. Conclusions A tailored theory for adult-onset offenders is unwarranted because few people begin crime de novo as adults. Official adult-onset offenders fall on a continuum of crime and its correlates, between official non-offenders and official juvenile-onset offenders. Existing theories can accommodate adult-onset offenders. PMID:27134318

Meta-Analysis of Attention-Deficit/Hyperactivity Disorder or Attention-Deficit/Hyperactivity Disorder Symptoms, Restriction Diet, and Synthetic Food Color Additives

Science.gov (United States)

Nigg, Joel T.; Lewis, Kara; Edinger, Tracy; Falk, Michael

2015-01-01

Objective The role of diet and of food colors in attention-deficit/hyperactivity disorder (ADHD) or its symptoms warrants updated quantitative meta-analysis, in light of recent divergent policy in Europe and the United States. Method Studies were identified through a literature search using the PubMed, Cochrane Library, and PsycNET databases through February 2011. Twenty-four publications met inclusion criteria for synthetic food colors; 10 additional studies informed analysis of dietary restriction. A random-effects meta-analytic model generated summary effect sizes. Results Restriction diets reduced ADHD symptoms at an effect of g = 0.29 (95% CI, 0.07–0.53). For food colors, parent reports yielded an effect size of g = 0.18 (95% CI, 0.08–0.24; p = .0007), which decreased to 0.12 (95% CI, 0.01–0.23; p attention, the summary effect size was 0.27 (95% CI = 0.07–0.47; p = .007) and survived correction. An estimated 8% of children with ADHD may have symptoms related to synthetic food colors. Conclusions A restriction diet benefits some children with ADHD. Effects of food colors were notable were but susceptible to publication bias or were derived from small, nongeneralizable samples. Renewed investigation of diet and ADHD is warranted. PMID:22176942

Drag reduction by natural polymeric additives in PMDS microchannel: Effect of types of additives

Directory of Open Access Journals (Sweden)

Ling Fiona W.M.

2017-01-01

Full Text Available Drag reduction technology was used in medical applications to enhance the blood flow in semiclogged blood streams which can be an alternative treatment for atherosclerosis. In this present study, natural polymeric drag reducing additives (DRA was introduced to replace synthetic polymer which has the possibility of bringing side effects to human health. Three different sources, namely okra, aloe vera and hibiscus were utilized to extract the natural polymeric additives which were then tested in custom made microchannel simulating human heart blood vessels. The performance of different types of additives was evaluated using pressure measurements. The maximum drag reduction up to 63.48% is achieved using 300 ppm of hibiscus mucilage at operating pressure of 50 mbar. In this present work, hibiscus showed the best drag reduction performance, giving the highest %FI in most of the cases. This experimental results proved that these natural polymeric additives could be utilized as DRA in enhancing the blood flow in semiclogged blood streams.

A new fetal RHD genotyping test: costs and benefits of mass testing to target antenatal anti-D prophylaxis in England and Wales.

Science.gov (United States)

Szczepura, Ala; Osipenko, Leeza; Freeman, Karoline

2011-01-18

Postnatal and antenatal anti-D prophylaxis have dramatically reduced maternal sensitisations and cases of rhesus disease in babies born to women with RhD negative blood group. Recent scientific advances mean that non-invasive prenatal diagnosis (NIPD), based on the presence of cell-free fetal DNA in maternal plasma, could be used to target prophylaxis on "at risk" pregnancies where the fetus is RhD positive. This paper provides the first assessment of cost-effectiveness of NIPD-targeted prophylaxis compared to current policies. We conducted an economic analysis of NIPD implementation in England and Wales. Two scenarios were considered. Scenario 1 assumed that NIPD will be only used to target antenatal prophylaxis with serology tests continuing to direct post-delivery prophylaxis. In Scenario 2, NIPD would also displace postnatal serology testing if an RhD negative fetus was identified. Costs were estimated from the provider's perspective for both scenarios together with a threshold royalty fee per test. Incremental costs were compared with clinical implications. The basic cost of an NIPD in-house test is £16.25 per sample (excluding royalty fee). The two-dose antenatal prophylaxis policy recommended by NICE is estimated to cost the NHS £3.37 million each year. The estimated threshold royalty fee is £2.18 and £8.83 for Scenarios 1 and 2 respectively. At a £2.00 royalty fee, mass NIPD testing would produce no saving for Scenario 1 and £507,154 per annum for Scenario 2. Incremental cost-effectiveness analysis indicates that, at a test sensitivity of 99.7% and this royalty fee, NIPD testing in Scenario 2 will generate one additional sensitisation for every £9,190 saved. If a single-dose prophylaxis policy were implemented nationally, as recently recommended by NICE, Scenario 2 savings would fall. Currently, NIPD testing to target anti-D prophylaxis is unlikely to be sufficiently cost-effective to warrant its large scale introduction in England and Wales. Only

Addition of atropine to submaximal exercise stress testing in patients evaluated for suspected ischaemia with SPECT imaging: a randomized, placebo-controlled trial

International Nuclear Information System (INIS)

Manganelli, Fiore; Sauro, Rosario; Di Lorenzo, Emilio; Rosato, Giuseppe; Spadafora, Marco; Varrella, Paola; Peluso, Giuseppina; Daniele, Stefania; Cuocolo, Alberto

2011-01-01

To evaluate the effects of the addition of atropine to exercise testing in patients who failed to achieve their target heart rate (HR) during stress myocardial perfusion imaging with single-photon emission computed tomography (SPECT). The study was a prospective, randomized, placebo-controlled design. Patients with suspected or known coronary artery disease who failed to achieve a target HR (≥85% of maximal predicted HR) during exercise SPECT imaging were randomized to receive intravenous atropine (n = 100) or placebo (n = 101). The two groups of patients did not differ with respect to demographic or clinical characteristics. A higher proportion of patients in the atropine group achieved the target HR compared to the placebo group (60% versus 3%, p < 0.0001). SPECT imaging was abnormal in a higher proportion of patients in the atropine group as compared to the placebo group (57% versus 42%, p < 0.05). Stress-induced myocardial ischaemia was present in more patients in the atropine group as compared to placebo (47% versus 29%, p < 0.01). In both groups of patients, no major side effects occurred. The addition of atropine at the end of exercise testing is more effective than placebo in raising HR to adequate levels, without additional risks of complications. The use of atropine in patients who initially failed to achieve their maximal predicted HR is associated with a higher probability of achieving a diagnostic myocardial perfusion study. (orig.)

Power transformer additional load losses separation procedure

Directory of Open Access Journals (Sweden)

Kostić Miloje M.

2011-01-01

Full Text Available The proposed procedure is based on the fact that total transformer losses (PLL1,n, determined by short circuit test, can be separated into two components: the eddy current losses in the windings (PEC1,n and stray flux losses (PSL1,n in iron parts of construction as well as in the transformer tank walls. The total additional load losses, PLLd1 and PLLdh, are determined by short circuit test results, conducted at rated frequency (f1 and at increased harmonic frequency (fh=h*f1. Using so obtained total additional load losses, PLLd1 and PLLdh, which can be expressed in the form PLLdh=PEC1,n*h2 + PSL1,n*h, the corresponding rate additional load losses values PEC1,n and PSL1,n are derived. At the end, for given load with predefined high harmonics content, (Ih/I1n, relative to rated current, the total additional load losses value ΣPLLdh > PLLd1, is found. In such a way all harmonics up to hmax are taken into account.

The neutralization of acidic coal mine lakes by additions of natural organic matter: a mesocosm test

International Nuclear Information System (INIS)

Brugam, R.B.; Gastineau, J.; Ratcliff, E.

1995-01-01

Cylindrical polyethylene enclosures 3 m in length and 1 m in diameter reaching from the surface to the bottom were constructed in an acid (pH=3.1) lake on a coal surface mine in southern Illinois. Wheat straw was added to the enclosures to test the effects of dissimilatory sulfate reduction on water chemistry. Added straw increased sulfide concentrations, raised pH to 6.5, reduced O 2 and increased acid neutralizing capacity of the enclosed water columns when compared with a control enclosure and with the open lake. Generation of acid neutralizing capacity exceeded the standing stock of sulfide indicating that sulfide was removed either by precipitation of FeS or outgassing of H 2 S. The pH and acid neutralizing capacity within the enclosures eventually returned to the level of the surrounding lake because of water exchange around the enclosure walls. Our results show that additions of organic matter to acid surface mine lakes result in the generation of acid neutralizing capacity

Preliminary benefit-cost analysis of the Fast Flux Test Facility (FFTF) power addition

International Nuclear Information System (INIS)

Callaway, J.M.; Lezberg, A.J.; Scott, M.J.; Tawil, J.J.

1984-07-01

The primary objective of this report is to conduct a preliminary benefit-cost study for the proposed power addition to FFTF to determine whether the project is cost-effective. If the project is authorized, construction will begin in 1986 and end in 1991. Full power operation is scheduled to begin in 1991 and a project life of 20 years is assumed. The undiscounted cost during the construction period of the FFTF power addition is estimated to be approximately $117 million over the construction period (1984 dollars). An additional $3 million is estimated as the opportunity cost - or value of these resources in their most favorable alternative use - of surplus FFTF equipment and unused CRBR equipment, including materials for steam generator fabrication. The annual operating and maintenance cost of the project is estimated to be about $2.1 million in 1984 dollars. 20 references

A test for clinal variation in Artemisia californica and associated arthropod responses to nitrogen addition.

Science.gov (United States)

Meza-Lopez, Maria M; Mooney, Kailen A; Thompson, Amanda L; Ho, Nicole K; Pratt, Jessica D

2018-01-01

The response of plant traits to global change is of fundamental importance to understanding anthropogenic impacts on natural systems. Nevertheless, little is known about plant genetic variation in such responses or the indirect effect of environmental change on higher trophic levels. In a three-year common garden experiment, we grew the shrub Artemisia californica from five populations sourced along a 700 km latitudinal gradient under ambient and nitrogen (N) addition (20 kg N ha-1) and measured plant traits and associated arthropods. N addition increased plant biomass to a similar extent among all populations. In contrast, N addition effects on most other plant traits varied among plant populations; N addition reduced specific leaf area and leaf percent N and increased carbon to nitrogen ratios in the two northern populations, but had the opposite or no effect on the three southern populations. N addition increased arthropod abundance to a similar extent among all populations in parallel with an increase in plant biomass, suggesting that N addition did not alter plant resistance to herbivores. N addition had no effect on arthropod diversity, richness, or evenness. In summary, genetic variation among A. californica populations mediated leaf-trait responses to N addition, but positive direct effects of N addition on plant biomass and indirect effects on arthropod abundance were consistent among all populations.

High-fertility phenotypes: two outbred mouse models exhibit substantially different molecular and physiological strategies warranting improved fertility.

Science.gov (United States)

Langhammer, Martina; Michaelis, Marten; Hoeflich, Andreas; Sobczak, Alexander; Schoen, Jennifer; Weitzel, Joachim M

2014-01-01

Animal models are valuable tools in fertility research. Worldwide, there are more than 400 transgenic or knockout mouse models available showing a reproductive phenotype; almost all of them exhibit an infertile or at least subfertile phenotype. By contrast, animal models revealing an improved fertility phenotype are barely described. This article summarizes data on two outbred mouse models exhibiting a 'high-fertility' phenotype. These mouse lines were generated via selection over a time period of more than 40 years and 161 generations. During this selection period, the number of offspring per litter and the total birth weight of the entire litter nearly doubled. Concomitantly with the increased fertility phenotype, several endocrine parameters (e.g. serum testosterone concentrations in male animals), physiological parameters (e.g. body weight, accelerated puberty, and life expectancy), and behavioral parameters (e.g. behavior in an open field and endurance fitness on a treadmill) were altered. We demonstrate that the two independently bred high-fertility mouse lines warranted their improved fertility phenotype using different molecular and physiological strategies. The fertility lines display female- as well as male-specific characteristics. These genetically heterogeneous mouse models provide new insights into molecular and cellular mechanisms that enhance fertility. In view of decreasing fertility in men, these models will therefore be a precious information source for human reproductive medicine. Translated abstract A German translation of abstract is freely available at http://www.reproduction-online.org/content/147/4/427/suppl/DC1.

Calcium addition in straw gasification

DEFF Research Database (Denmark)

Risnes, H.; Fjellerup, Jan Søren; Henriksen, Ulrik Birk

2003-01-01

The present work focuses on the influence of calcium addition in gasification. The inorganic¿organic element interaction as well as the detailed inorganic¿inorganic elements interaction has been studied. The effect of calcium addition as calcium sugar/molasses solutions to straw significantly...... affected the ash chemistry and the ash sintering tendency but much less the char reactivity. Thermo balance test are made and high-temperature X-ray diffraction measurements are performed, the experimental results indicate that with calcium addition major inorganic¿inorganic reactions take place very late...... in the char conversion process. Comprehensive global equilibrium calculations predicted important characteristics of the inorganic ash residue. Equilibrium calculations predict the formation of liquid salt if sufficient amounts of Ca are added and according to experiments as well as calculations calcium binds...

Role of anaerobic fungi in wheat straw degradation and effects of plant feed additives on rumen fermentation parameters in vitro.

Science.gov (United States)

Dagar, S S; Singh, N; Goel, N; Kumar, S; Puniya, A K

2015-01-01

In the present study, rumen microbial groups, i.e. total rumen microbes (TRM), total anaerobic fungi (TAF), avicel enriched bacteria (AEB) and neutral detergent fibre enriched bacteria (NEB) were evaluated for wheat straw (WS) degradability and different fermentation parameters in vitro. Highest WS degradation was shown for TRM, followed by TAF, NEB and least by AEB. Similar patterns were observed with total gas production and short chain fatty acid profiles. Overall, TAF emerged as the most potent individual microbial group. In order to enhance the fibrolytic and rumen fermentation potential of TAF, we evaluated 18 plant feed additives in vitro. Among these, six plant additives namely Albizia lebbeck, Alstonia scholaris, Bacopa monnieri, Lawsonia inermis, Psidium guajava and Terminalia arjuna considerably improved WS degradation by TAF. Further evaluation showed A. lebbeck as best feed additive. The study revealed that TAF plays a significant role in WS degradation and their fibrolytic activities can be improved by inclusion of A. lebbeck in fermentation medium. Further studies are warranted to elucidate its active constituents, effect on fungal population and in vivo potential in animal system.

Computerized neurocognitive testing in the management of sport-related concussion: an update.

Science.gov (United States)

Resch, Jacob E; McCrea, Michael A; Cullum, C Munro

2013-12-01

Since the late nineties, computerized neurocognitive testing has become a central component of sport-related concussion (SRC) management at all levels of sport. In 2005, a review of the available evidence on the psychometric properties of four computerized neuropsychological test batteries concluded that the tests did not possess the necessary criteria to warrant clinical application. Since the publication of that review, several more computerized neurocognitive tests have entered the market place. The purpose of this review is to summarize the body of published studies on psychometric properties and clinical utility of computerized neurocognitive tests available for use in the assessment of SRC. A review of the literature from 2005 to 2013 was conducted to gather evidence of test-retest reliability and clinical validity of these instruments. Reviewed articles included both prospective and retrospective studies of primarily sport-based adult and pediatric samples. Summaries are provided regarding the available evidence of reliability and validity for the most commonly used computerized neurocognitive tests in sports settings.

The conceptualisation and measurement of DSM-5 Internet Gaming Disorder: the development of the IGD-20 Test.

Directory of Open Access Journals (Sweden)

Halley M Pontes

Full Text Available Over the last decade, there has been growing concern about 'gaming addiction' and its widely documented detrimental impacts on a minority of individuals that play excessively. The latest (fifth edition of the American Psychiatric Association's Diagnostic and Statistical Manual of Mental Disorders (DSM-5 included nine criteria for the potential diagnosis of Internet Gaming Disorder (IGD and noted that it was a condition that warranted further empirical study.The main aim of this study was to develop a valid and reliable standardised psychometrically robust tool in addition to providing empirically supported cut-off points.A sample of 1003 gamers (85.2% males; mean age 26 years from 57 different countries were recruited via online gaming forums. Validity was assessed by confirmatory factor analysis (CFA, criterion-related validity, and concurrent validity. Latent profile analysis was also carried to distinguish disordered gamers from non-disordered gamers. Sensitivity and specificity analyses were performed to determine an empirical cut-off for the test.The CFA confirmed the viability of IGD-20 Test with a six-factor structure (salience, mood modification, tolerance, withdrawal, conflict and relapse for the assessment of IGD according to the nine criteria from DSM-5. The IGD-20 Test proved to be valid and reliable. According to the latent profile analysis, 5.3% of the total participants were classed as disordered gamers. Additionally, an optimal empirical cut-off of 71 points (out of 100 seemed to be adequate according to the sensitivity and specificity analyses carried.The present findings support the viability of the IGD-20 Test as an adequate standardised psychometrically robust tool for assessing internet gaming disorder. Consequently, the new instrument represents the first step towards unification and consensus in the field of gaming studies.

The Conceptualisation and Measurement of DSM-5 Internet Gaming Disorder: The Development of the IGD-20 Test

Science.gov (United States)

Pontes, Halley M.; Király, Orsolya; Demetrovics, Zsolt; Griffiths, Mark D.

2014-01-01

Background Over the last decade, there has been growing concern about ‘gaming addiction’ and its widely documented detrimental impacts on a minority of individuals that play excessively. The latest (fifth) edition of the American Psychiatric Association's Diagnostic and Statistical Manual of Mental Disorders (DSM-5) included nine criteria for the potential diagnosis of Internet Gaming Disorder (IGD) and noted that it was a condition that warranted further empirical study. Aim: The main aim of this study was to develop a valid and reliable standardised psychometrically robust tool in addition to providing empirically supported cut-off points. Methods A sample of 1003 gamers (85.2% males; mean age 26 years) from 57 different countries were recruited via online gaming forums. Validity was assessed by confirmatory factor analysis (CFA), criterion-related validity, and concurrent validity. Latent profile analysis was also carried to distinguish disordered gamers from non-disordered gamers. Sensitivity and specificity analyses were performed to determine an empirical cut-off for the test. Results The CFA confirmed the viability of IGD-20 Test with a six-factor structure (salience, mood modification, tolerance, withdrawal, conflict and relapse) for the assessment of IGD according to the nine criteria from DSM-5. The IGD-20 Test proved to be valid and reliable. According to the latent profile analysis, 5.3% of the total participants were classed as disordered gamers. Additionally, an optimal empirical cut-off of 71 points (out of 100) seemed to be adequate according to the sensitivity and specificity analyses carried. Conclusions The present findings support the viability of the IGD-20 Test as an adequate standardised psychometrically robust tool for assessing internet gaming disorder. Consequently, the new instrument represents the first step towards unification and consensus in the field of gaming studies. PMID:25313515

The conceptualisation and measurement of DSM-5 Internet Gaming Disorder: the development of the IGD-20 Test.

Science.gov (United States)

Pontes, Halley M; Király, Orsolya; Demetrovics, Zsolt; Griffiths, Mark D

2014-01-01

Over the last decade, there has been growing concern about 'gaming addiction' and its widely documented detrimental impacts on a minority of individuals that play excessively. The latest (fifth) edition of the American Psychiatric Association's Diagnostic and Statistical Manual of Mental Disorders (DSM-5) included nine criteria for the potential diagnosis of Internet Gaming Disorder (IGD) and noted that it was a condition that warranted further empirical study. The main aim of this study was to develop a valid and reliable standardised psychometrically robust tool in addition to providing empirically supported cut-off points. A sample of 1003 gamers (85.2% males; mean age 26 years) from 57 different countries were recruited via online gaming forums. Validity was assessed by confirmatory factor analysis (CFA), criterion-related validity, and concurrent validity. Latent profile analysis was also carried to distinguish disordered gamers from non-disordered gamers. Sensitivity and specificity analyses were performed to determine an empirical cut-off for the test. The CFA confirmed the viability of IGD-20 Test with a six-factor structure (salience, mood modification, tolerance, withdrawal, conflict and relapse) for the assessment of IGD according to the nine criteria from DSM-5. The IGD-20 Test proved to be valid and reliable. According to the latent profile analysis, 5.3% of the total participants were classed as disordered gamers. Additionally, an optimal empirical cut-off of 71 points (out of 100) seemed to be adequate according to the sensitivity and specificity analyses carried. The present findings support the viability of the IGD-20 Test as an adequate standardised psychometrically robust tool for assessing internet gaming disorder. Consequently, the new instrument represents the first step towards unification and consensus in the field of gaming studies.

Reliability Testing Beyond Qualification as a Key Component in Photovoltaic's Progress Toward Grid Parity: Preprint

Energy Technology Data Exchange (ETDEWEB)

Wohlgemuth, J. H.; Kurtz, S.

2011-02-01

This paper discusses why it is necessary for new lower cost PV modules to be tested using a reliability test sequence that goes beyond the Qualification test sequence now utilized for modules. Today most PV modules are warranted for 25 years, but the Qualification Test Sequence does not test for 25-year life. There is no accepted test protocol to validate a 25-year lifetime. This paper recommends the use of long term accelerated testing to compare now designs directly with older designs that have achieved long lifetimes in outdoor exposure. If the new designs do as well or better than the older ones, then it is likely that they will survive an equivalent length of time in the field.

Role of Academic Self-efficacy and Social Support on Nursing Students' Test Anxiety.

Science.gov (United States)

Warshawski, Sigalit; Bar-Lev, Oshra; Barnoy, Sivia

2018-05-25

Associations between test anxiety, academic self-efficacy (ASE), and social support through social media have not been fully explored. The purposes were to explore associations between test anxiety, ASE, and social support from social media and to examine differences in test anxiety by students' year of studies and cultural background. This study used a cross-sectional, descriptive design. The sample comprised first- and fourth-year nursing students (n = 240) attending a baccalaureate nursing program in Israel. Higher ASE and support through social media were related to lower test anxiety. Fourth-year students and Jewish students had higher ASE than first-year and Arab students, who received more support on social media than Jewish students. Developing learning strategies designed to increase students' ASE and reduce test anxiety is warranted. Social media as an educational tool can be adopted for this purpose.

Performance Characteristic of Cold Recycled Mixture with Asphalt Emulsion and Chemical Additives

Directory of Open Access Journals (Sweden)

Shaowen Du

2015-01-01

Full Text Available Three types of chemical additives were used to modify asphalt emulsion recycled mixture. These chemical additives include composite Portland cement (CPC, hydrated lime (HL, and a combination of hydrated lime and ground-granulated blast-furnace slag (GGBF. The influence of different additives on the recycled mixture performance was investigated by volumetric and strength tests, moisture susceptibility test, rutting resistance test, and low temperature bending test. To better understand its performance characteristic, the microstructure images of the recycled mixture were observed by environmental scanning electron microscope (ESEM. Test results demonstrate that the performance improvement of the emulsion recycled mixture depends on the types and content of chemical additives. Several recommendations are presented for the selection of chemical materials. Based on ESEM image analysis, the interface bonding mechanism is proposed to explain the performance characteristic of the recycled mixture with asphalt emulsion and cementitious materials.

Design and additive manufacture for flow chemistry.

Science.gov (United States)

Capel, Andrew J; Edmondson, Steve; Christie, Steven D R; Goodridge, Ruth D; Bibb, Richard J; Thurstans, Matthew

2013-12-07

We review the use of additive manufacturing (AM) as a novel manufacturing technique for the production of milli-scale reactor systems. Five well-developed additive manufacturing techniques: stereolithography (SL), multi-jet modelling (MJM), selective laser melting (SLM), laser sintering (LS) and fused deposition modelling (FDM) were used to manufacture a number of miniaturised reactors which were tested using a range of organic and inorganic reactions.

Investigation of OMNIgene·SPUTUM performance in delayed tuberculosis testing by smear, culture, and Xpert MTB/RIF assays in Uganda

Directory of Open Access Journals (Sweden)

C.D. Kelly-Cirino

2017-06-01

Full Text Available OMNIgene·SPUTUM (OM-S is a sample transport reagent designed to work with all tuberculosis diagnostics while eliminating the need for cold chain. OM-S-treated sputum samples were assayed in several tests after multiday holds. Raw sputa from 100 patients underwent direct smear microscopy, were manually split and assigned to the OM-S group [OM-S added at collection (no other processing required and tested after 0- to 5-day holds at room temperature] or standard-of-care (SOC group (NaOH/N-acetyl l-cysteine decontamination, all tested on day of collection. Concentrated smear microscopy, Lowenstein Jensen (LJ culture, and mycobacteria growth indicator tube (MGIT culture were performed. For patients with negative direct smear, a second sample was split, with SOC (raw sputum and OM-S portions (sediment tested in the Xpert MTB/RIF (Xpert assay. OM-S group and SOC group results were strongly concordant on all four tests [range, 89% (MGIT–97% (Xpert]. OM-S MGIT, LJ, and Xpert tests were in statistical agreement with SOC MGIT as reference. OM-S specimens had lower culture contamination rates (3% vs. 10% LJ; 2% vs. 5% MGIT but required, on average, 5.6 additional days to become MGIT-positive. The findings suggest that samples held/transported in OM-S are compatible with smear microscopy, LJ or MGIT culture, and Xpert, and perform comparably to fresh sputum samples. Larger feasibility studies are warranted.

Additive Manufacturing Thermal Performance Testing of Single Channel GRCop-84 SLM Components

Science.gov (United States)

Garcia, Chance P.; Cross, Matthew

2014-01-01

The surface finish found on components manufactured by sinter laser manufacturing (SLM) is rougher (0.013 - 0.0006 inches) than parts made using traditional fabrication methods. Internal features and passages built into SLM components do not readily allow for roughness reduction processes. Alternatively, engineering literature suggests that the roughness of a surface can enhance thermal performance within a pressure drop regime. To further investigate the thermal performance of SLM fabricated pieces, several GRCop-84 SLM single channel components were tested using a thermal conduction rig at MSFC. A 20 kW power source running at 25% duty cycle and 25% power level applied heat to each component while varying water flow rates between 2.1 - 6.2 gallons/min (GPM) at a supply pressure of 550 to 700 psi. Each test was allowed to reach quasi-steady state conditions where pressure, temperature, and thermal imaging data were recorded. Presented in this work are the heat transfer responses compared to a traditional machined OHFC Copper test section. An analytical thermal model was constructed to anchor theoretical models with the empirical data.

The use of the rapid osmotic fragility test as an additional test to diagnose canine immune-mediated haemolytic anaemia

DEFF Research Database (Denmark)

Paes, Geert; Paepe, Dominique; Meyer, Evelyne

2013-01-01

Background: Diagnosing canine immune-mediated haemolytic anaemia (IMHA) is often challenging because all currently available tests have their limitations. Dogs with IMHA often have an increased erythrocyte osmotic fragility (OF), a characteristic that is sometimes used in the diagnosis of IMHA...... hyperlipemic dogs (group 3), 10 dogs with lymphoma (group 4), 8 dogs with an infection (group 5) and 13 healthy dogs (group 6) were included. In all dogs, blood smear examination, in-saline auto-agglutination test, Coombs' test, COFT and ROFT were performed. In the COFT, OF5, OF50 and OF90 were defined...

Biocompatibility of photopolymers for additive manufacturing

Directory of Open Access Journals (Sweden)

Leonhardt Stefan

2016-09-01

Full Text Available To establish photopolymers for the production of class II or class III medical products by additive manufacturing it is essential to know which components of photopolymeric systems, consisting of monomers, photoinitiators and additives, are the determining factors on their biocompatible properties. In this study the leachable substances of a cured photopolymeric system were eluted and identified by HPLC-MS detection. In addition the cured photopolymer was testes for cytotoxicity and genotoxicity according to DIN EN ISO 10993 for long time applications. The results showed that uncured residual monomers are the determining factor on the biocompatible properties of the photopolymeric system. Strategies to reduce these residual monomers in the cured photopolymer are presented.

Development of the Military Women's Attitudes Toward Menstrual Suppression Scale: from construct definition to pilot testing.

Science.gov (United States)

Trego, Lori L

2009-01-01

The Military Women's Attitudes Toward Menstrual Suppression scale (MWATMS) was created to measure attitudes toward menstrual suppression during deployment. The human health and social ecology theories were integrated to conceptualize an instrument that accounts for military-unique aspects of the environment on attitudes toward suppression. A three-step instrument development process was followed to develop the MWATMS. The instrument was pilot tested on a convenience sample of 206 military women with deployment experience. Reliability was tested with measures of internal consistency (alpha = .97); validity was tested with principal components analysis with varimax rotation. Four components accounted for 65% of variance: Benefits/Interest, Hygiene, Convenience, and Soldier/Stress. The pilot test of the MWATMS supported its reliability and validity. Further testing is warranted for validation of this instrument.

QTc interval prolongation in children with Turner syndrome: the results of exercise testing and 24-h ECG.

Science.gov (United States)

Dalla Pozza, Robert; Bechtold, Susanne; Urschel, Simon; Netz, Heinrich; Schwarz, Hans-Peter

2009-01-01

Turner syndrome (TS) is the most common sex chromosome abnormality in females. Recently, a prolongation of the rate-corrected QT (QTc) interval in the electrocardiogram (ECG) of TS patients has been reported. A prolonged QTc interval has been correlated to an increased risk for sudden cardiac death, and medical treatment is warranted in patients with congenital long QT syndrome (LQTS). Additionally, several drugs of common use are contraindicated in LQTS because of their effects on myocardial repolarization. The importance of the QTc prolongation in TS patients is not known at present. Eighteen TS patients with a prolonged QTc interval (group 1) and 11 TS patients with a normal QTc interval (group 2) (mean age 12.6+/-3.1 vs. 11.8+/-2.1 years, respectively) were tested. The QTc interval was calculated during exercise testing and during 24-h ECG recordings. None of the patients experienced adverse cardiac events during the tests. The mean QTc interval decreased from 0.467 to 0.432 s in group 1 and from 0.432 to 0.412 s in group 2. During the 24-h ECG, the maximum QTc interval was significantly prolonged in group 1 (0.51 vs. 0.465 s, pinformation about the cardiac risk in the single TS patient with a prolonged QTc interval. This helps in counseling these girls, as clear therapeutic guidelines are currently lacking.

'Thinking ill of others without sufficient warrant?' Transcending the accuracy-inaccuracy dualism in prejudice and stereotyping research.

Science.gov (United States)

Dixon, John

2017-03-01

Research on prejudice seeks to understand and transform inaccurate beliefs about others. Indeed, historically such research has offered a cautionary tale of the biased nature of human cognition. Recently, however, this view has been challenged by work defending the essential rationality of intergroup perception, a theme captured controversially in Jussim and colleagues' (2009) research on the 'unbearable accuracy of stereotyping'. The present paper argues that in its own terms the 'rationalist turn' in socio-cognitive research on stereotyping presents an important challenge to the prejudice tradition, raising troubling questions about its conceptual and empirical foundations. However, it also argues for the necessity of transcending those terms. By focusing on the correspondence between individual beliefs and the supposedly 'objective' characteristics of others, we neglect the historical and discursive practices through which the social realities that we 'perceive' are actively constructed and institutionalized. We mask their social origins, contested and perspectival nature, relativity, and relationship to wider structures of power. By implication, moving beyond the Allportian perspective that has dominated both the prejudice tradition and the emerging stereotype accuracy paradigm, we may now need to prioritize other kinds of questions. Reversing Allport's famous definition of prejudice, it may now be time to ask: How, and with what consequences, does 'thinking ill of others' become sufficiently warranted? How does such thinking become part of institutionalized relations of power and an accepted way of perceiving, evaluating and treating others? What should social psychologists be doing to challenge this state of affairs? © 2017 The British Psychological Society.

Does the health status of intimate partner violence victims warrant pharmacies as portals for public health promotion?

Science.gov (United States)

Cerulli, Catherine; Cerulli, Jennifer; Santos, Elizabeth J; Lu, Najii; He, Hua; Kaukeinen, Kimberly; White, Anne Marie; Tu, Xin

To explore whether the health status of intimate partner violence (IPV) victims warrants pharmacies to be portals for public health promotion. Specific objectives included (1) identifying prevalence of IPV including domestic violence (DV) and sexual assault (SA) in a community sample, (2) describing characteristics and correlates of DV/SA between participants who reported and did not report DV/SA, and (3) exploring whether DV/SA status is related to mental health medication use. Cross sectional. Upstate New York during 2006. English- and Spanish-speaking respondents younger than 65 years of age answering four questions to assess DV/SA. Secondary analysis of a countywide random telephone survey, the 2006 Monroe County Adult Health Survey, which collects prevalence data on health behaviors and health status indicators. To determine whether those reporting DV/SA are at increased odds for mental health medication use, controlling for other sociodemographic- and health-related variables. The survey response rate was 30.3%, with 1,881 respondents meeting inclusion criteria. Those reporting DV/SA were almost twice as likely to use mental health medications. However, when controlling for other variables, only poor mental and physical health were significant in increasing the odds of mental health medication use. The analyses reported here suggest that DV/SA victims in a community sample use mental health medications. When controlling for other variables, survey respondents reported worse physical and mental health. If pharmacies are suitable portals for DV/SA outreach, curricula would need to provide the knowledge and skills needed to take an active role in this public health promotion.

The Seasonal KPSS Test: Examining Possible Applications with Monthly Data and Additional Deterministic Terms

Directory of Open Access Journals (Sweden)

Ghassen El Montasser

2015-05-01

Full Text Available The literature has been notably less definitive in distinguishing between finite sample studies of seasonal stationarity than in seasonal unit root tests. Although the use of seasonal stationarity and unit root tests is advised to determine correctly the most appropriate form of the trend in a seasonal time series, such a use is rarely noted in the relevant studies on this topic. Recently, the seasonal KPSS test, with a null hypothesis of no seasonal unit roots, and based on quarterly data, has been introduced in the literature. The asymptotic theory of the seasonal KPSS test depends on whether data have been filtered by a preliminary regression. More specifically, one may proceed to extracting deterministic components, such as the mean and trend, from the data before testing. In this paper, we examine the effects of de-trending on the properties of the seasonal KPSS test in finite samples. A sketch of the test’s limit theory is subsequently provided. Moreover, a Monte Carlo study is conducted to analyze the behavior of the test for a monthly time series. The focus on this time-frequency is significant because, as we mentioned above, it was introduced for quarterly data. Overall, the results indicated that the seasonal KPSS test preserved its good size and power properties. Furthermore, our results corroborate those reported elsewhere in the literature for conventional stationarity tests. These subsequent results assumed that the nonparametric corrections of residual variances may lead to better in-sample properties of the seasonal KPSS test. Next, the seasonal KPSS test is applied to a monthly series of the United States (US consumer price index. We were able to identify a number of seasonal unit roots in this time series. [1] [1]    Table 1 in this paper is copyrighted and initially published by JMASM in 2012, Volume 11, Issue 1, pp. 69–77, ISSN: 1538–9472, JMASM Inc., PO Box 48023, Oak Park, MI 48237, USA, ea@jmasm.com.

Interventions to Improve Rate of Diabetes Testing Postpartum in Women With Gestational Diabetes Mellitus.

Science.gov (United States)

Hamel, Maureen S; Werner, Erika F

2017-02-01

Gestational diabetes mellitus (GDM) is one of the most common medical complications of pregnancy. In the USA, four million women are screened annually for GDM in pregnancy in part to improve pregnancy outcomes but also because diagnosis predicts a high risk of future type 2 diabetes mellitus (T2DM). Therefore, among women with GDM, postpartum care should be focused on T2DM prevention. This review describes the current literature aimed to increase postpartum diabetes testing among women with GDM. Data suggest that proactive patient contact via a health educator, a phone call, or even postal mail is associated with higher rates of postpartum diabetes testing. There may also be utility to changing the timing of postpartum diabetes testing. Despite the widespread knowledge regarding the importance of postpartum testing for women with GDM, testing rates remain low. Alternative testing strategies and large randomized trials addressing postpartum testing are warranted.

Defining Investment Additionality for CDM projects - practical approaches

International Nuclear Information System (INIS)

Greiner, Sandra; Michaelowa, Axel

2003-01-01

The environmental integrity of the CDM under the Kyoto Protocol depends on the possibility to avoid giving emission credits to projects that would have happened anyway. Whether and how 'Investment Additionality' of CDM projects has to be determined is currently a part of climate negotiations. We discuss the rationale of companies to invest in projects and analyse possible criteria to determine Investment Additionality from a theoretical point of view. Differences in the type of investment call for the application of different criteria. Although some criteria are better than others, no single criterion can outweigh the others in all respects. We therefore suggest a scheme for additionality testing that aims at matching types of investment and criteria in a sensible way. Criteria are evaluated on the grounds of robustness to manipulation, degree of coverage and appropriateness for testing the investment decision under consideration

A Fully Non-Metallic Gas Turbine Engine Enabled by Additive Manufacturing

Science.gov (United States)

Grady, Joseph E.; Halbig, Michael C.; Singh, Mrityunjay

2015-01-01

In a NASA Aeronautics Research Institute (NARI) sponsored program entitled "A Fully Non-Metallic Gas Turbine Engine Enabled by Additive Manufacturing", evaluation of emerging materials and additive manufacturing technologies was carried out. These technologies may enable fully non-metallic gas turbine engines in the future. This paper highlights the results of engine system trade studies which were carried out to estimate reduction in engine emissions and fuel burn enabled due to advanced materials and manufacturing processes. A number of key engine components were identified in which advanced materials and additive manufacturing processes would provide the most significant benefits to engine operation. In addition, feasibility of using additive manufacturing technologies to fabricate gas turbine engine components from polymer and ceramic matrix composite were demonstrated. A wide variety of prototype components (inlet guide vanes (IGV), acoustic liners, engine access door) were additively manufactured using high temperature polymer materials. Ceramic matrix composite components included first stage nozzle segments and high pressure turbine nozzle segments for a cooled doublet vane. In addition, IGVs and acoustic liners were tested in simulated engine conditions in test rigs. The test results are reported and discussed in detail.

An evaluation of estimation methods for determining addition in presbyopes.

Science.gov (United States)

Bittencourt, Leonardo Catunda; Alves, Milton Ruiz; Dantas, Daniel Oliveira; Rodrigues, Pablo Felipe; Santos-Neto, Edson dos

2013-01-01

The optical correction of presbyopia must be handled individually. Our aim was to compare the methods used in addition to the refractive near vision, with the final addition used in presbyopic patients. Eighty healthy subjects with a mean age of 49.7 years (range 40 to 60 years) were studied. Tentative near additions were determined using four different techniques: one-half amplitude accommodation with minus lenses (AAL); one-third accommodative demand with positive lens (ADL); balanced range of accommodation with minus and positive lenses (BRA) and crossed cylinder test with initial myopisation (CCT). The power of the addition was then refined to arrive at the final addition. The mean tentative near additions were lower than the final addition for ADL and BRA addition methods. The mean differences between tentative and final additions were low for all the tests examined (less than 0.25 D). The intervals between the 95% limits of agreement differed substantially and were always higher than ±0.50 D. All the methods used displayed similar behavior and provided a tentative addition close to the final addition. The coefficient of agreements (COA) detected suggests that every tentative addition should be adjusted according to the particular needs of the patient.

An evaluation of estimation methods for determining addition in presbyopes

Directory of Open Access Journals (Sweden)

Leonardo Catunda Bittencourt

2013-08-01

Full Text Available PURPOSE: The optical correction of presbyopia must be handled individually. Our aim was to compare the methods used in addition to the refractive near vision, with the final addition used in presbyopic patients. METHODS: Eighty healthy subjects with a mean age of 49.7 years (range 40 to 60 years were studied. Tentative near additions were determined using four different techniques: one-half amplitude accommodation with minus lenses (AAL; one-third accommodative demand with positive lens (ADL; balanced range of accommodation with minus and positive lenses (BRA and crossed cylinder test with initial myopisation (CCT. The power of the addition was then refined to arrive at the final addition. RESULTS: The mean tentative near additions were lower than the final addition for ADL and BRA addition methods. The mean differences between tentative and final additions were low for all the tests examined (less than 0.25 D. The intervals between the 95% limits of agreement differed substantially and were always higher than ±0.50 D. CONCLUSION: All the methods used displayed similar behavior and provided a tentative addition close to the final addition. The coefficient of agreements (COA detected suggests that every tentative addition should be adjusted according to the particular needs of the patient.

Neuropathy Tests

Science.gov (United States)

... LD) Lactoferrin Lactose Tolerance Tests LDL Cholesterol LDL Particle Testing (LDL-P) Lead Legionella Testing Leptin Levetiracetam Lipase ... tests, such as computed tomography (CT) scans or magnetic resonance imaging ... suspected, additional testing may be performed to evaluate heart rate, blood ...

Formulation of Antibacterial Liquid Soap from Nyamplung Seed Oil (Calophyllum inophyllum L) with Addition of Curcuma heyneana and its Activity Test on Staphylococcus aureus

Science.gov (United States)

Widyaningsih, S.; Chasani, M.; Diastuti, H.; Novayanti

2018-04-01

The increasing demand of soap encourages new innovations of it’s quantity, quality, benefits and raw materials. One of the innovations that has been developed is the use of nyamplung (C. inophyllum L) seed oil as basic ingredients of soap, with addition of active substances such as antibacterial and fragrance. This research aims to determine best formulation of liquid soap according to SNI 06-4085-1996 and its antibacterial activity after addition of n-hexane fraction of C. heyneana rhizome and fragrance from lavender flower oil at various concentrations, then a hedonic test was conducted to evaluate the panelist's preference towards the soap with the best formulation. This research has been done through several stages of soap making with saponification method, soap characterization according to SNI 06-4085-1996, determination of best formulation of liquid soap based on the effectiveness index method and antibacterial activity test of liquid soap to S.aureus with disc diffusion method and hedonic test using some parameters such as colour, odor, foam, clean power and effects after being used. The results showed that the best characteristic soap according to SNI 06-4085-1996 was soap with 0.2% antibacterial content and 2.5% perfume. The best soap characteristic showed total fatty acid 67.49%, free fatty acid 1.01%, neutral fat 7.24%, weight of type 1.05 g/mL, pH of 9.85 and foam stability 76.69%. The results of the antibacterial activity test of the best formula soap showed the inhibitory zone of 14.92 mm.

Diagnosis of feline infectious peritonitis: Update on evidence supporting available tests.

Science.gov (United States)

Tasker, Séverine

2018-03-01

Practical relevance: Feline coronavirus (FCoV) infection is very common in cats, usually causing only mild intestinal signs such as diarrhoea. Up to 10% of FCoV infections, however, result in the fatal disease feline infectious peritonitis (FIP). Clinical challenges: Obtaining a definitive diagnosis of FIP based on non-invasive approaches is difficult. Confirmation of the disease relies on finding appropriate cytological or histopathological changes in association with positive immunostaining for FCoV antigen. In FIP cases with effusions, cytology and immunostaining on effusion samples can be relatively easy to perform; otherwise obtaining diagnostic samples is more challenging and collection of biopsies from tissues with gross lesions is necessary. In the absence of a definitive diagnosis, a high index of suspicion of FIP may be obtained from the cat's signalment and history, combined with findings on clinical examination and laboratory test results. If largely consistent with FIP, these can be used as a basis for discussion with the owner about whether additional, more invasive, diagnostic tests are warranted. In some cases it may be that euthanasia is discussed as an alternative to pursuing a definitive diagnosis ante-mortem, especially if financial limitations exist or where there are concerns over a cat's ability to tolerate invasive diagnostic procedures. Ideally, the diagnosis should be confirmed in such patients from samples taken at post-mortem examination. Global importance: FIP occurs wherever FCoV infection is present in cats, which equates to most parts of the world. Evidence base: This review provides a comprehensive overview of how to approach the diagnosis of FIP, focusing on the tests available to the veterinary practitioner and recently published evidence supporting their use.

Pediatric near-drowning events: do they warrant trauma team activation?

Science.gov (United States)

Chotai, Pranit N; Manning, Lisa; Eithun, Benjamin; Ross, Joshua C; Eubanks, James W; Hamner, Chad; Gosain, Ankush

2017-05-15

The purpose of this study was to determine the incidence of traumatic injuries, factors associated with mortality, and need for pediatric trauma surgery involvement for drowning and near-drowning events in children. An institutional review board-approved, retrospective chart review was performed at three American College of Surgeons-verified Pediatric Trauma Centers (2011-2014). Patients with International Classification of Diseases, Ninth Revision, codes or E-codes for fatal-nonfatal drowning, fall into water, accidental drowning, or submersion were included. Bivariate analysis using chi-square or Fisher exact test for nominal variables and Mann-Whitney U test for continuous variables was performed. A total of 363 patients (median 3.17 y [18 d-17 y]) met the inclusion criteria. Drowning sites included pool (81.5%), bathtub (12.9%), and natural water (5.2%). A witnessed fall or dive was reported in 34.9%, 57.9% did not fall or dive, and 7% had an unwitnessed event. Most patients did not undergo cervical spine (83%) or brain imaging (75.5%). Seven patients (1.92%) had associated soft tissue injuries. Two patients (0.006%) received surgical intervention (bronchoscopy and extracorporeal membrane oxygenation) within 24 h of presentation. Only 2.2% were admitted to the pediatric trauma service. The percentage of patients discharged home from the emergency department was 10.2%. Overall mortality was 12.4%. Factors associated with mortality included transfer from outside hospital (P = 0.016), presence of hypothermia on arrival (P drowning in a pool (P = 0.013), or undergoing brain cooling at admission (P = 0.011). This is the largest reported series of pediatric near-drowning events. Only rarely did patients require immediate surgical attention and the majority were admitted to nonsurgical services. These data suggest that routine pediatric trauma surgery service involvement in patients with near-drowning events may be unnecessary. Copyright © 2017 Elsevier

Validity of a new assessment rubric for a short-answer test of clinical reasoning.

Science.gov (United States)

Yeung, Euson; Kulasagarem, Kulamakan; Woods, Nicole; Dubrowski, Adam; Hodges, Brian; Carnahan, Heather

2016-07-26

The validity of high-stakes decisions derived from assessment results is of primary concern to candidates and certifying institutions in the health professions. In the field of orthopaedic manual physical therapy (OMPT), there is a dearth of documented validity evidence to support the certification process particularly for short-answer tests. To address this need, we examined the internal structure of the Case History Assessment Tool (CHAT); this is a new assessment rubric developed to appraise written responses to a short-answer test of clinical reasoning in post-graduate OMPT certification in Canada. Fourteen physical therapy students (novices) and 16 physical therapists (PT) with minimal and substantial OMPT training respectively completed a mock examination. Four pairs of examiners (n = 8) participated in appraising written responses using the CHAT. We conducted separate generalizability studies (G studies) for all participants and also by level of OMPT training. Internal consistency was calculated for test questions with more than 2 assessment items. Decision studies were also conducted to determine optimal application of the CHAT for OMPT certification. The overall reliability of CHAT scores was found to be moderate; however, reliability estimates for the novice group suggest that the scale was incapable of accommodating for scores of novices. Internal consistency estimates indicate item redundancies for several test questions which will require further investigation. Future validity studies should consider discriminating the clinical reasoning competence of OMPT trainees strictly at the post-graduate level. Although rater variance was low, the large variance attributed to error sources not incorporated in our G studies warrant further investigations into other threats to validity. Future examination of examiner stringency is also warranted.

Solubility Testing of Sucrose Esters of Fatty Acids in International Food Additive Specifications.

Science.gov (United States)

Nagai, Yukino; Kawano, Satoko; Motoda, Kenichiro; Tomida, Masaaki; Tatebe, Chiye; Sato, Kyoko; Akiyama, Hiroshi

2017-03-01

We investigated the solubility of 10 samples of sucrose esters of fatty acids (SEFA) products that are commercially available worldwide as food additives (emulsifiers). Although one sample dissolved transparently in both water and ethanol, other samples produced white turbidity and/or precipitates and did not meet the solubility criterion established by the Joint Food and Agriculture Organization of the United Nations (FAO)/WHO Expert Committee on Food Additives (JECFA). When the sample solutions were heated, the solubility in both water and ethanol increased. All of the samples dissolved transparently in ethanol, and dispersed and became white without producing precipitates in water. The present study suggests that the current solubility criterion of the JECFA SEFA specifications needs to be revised.

How many food additives are rodent carcinogens?

Science.gov (United States)

Johnson, F M

2002-01-01

One generally assumes that chemical agents added to foods are reasonably free of risks to human health, and practically everyone consumes some additives in his or her food daily throughout life. In the United States, the 1958 Food Additives Amendment to the Federal Food, Drug and Cosmetic Act of 1938 requires food manufacturers to demonstrate the safety of food additives to the Food and Drug Administration (FDA). The Amendment contains a provision that prohibits approval of an additive if it is found to cause cancer in humans or animals. In the present study, data from the National Toxicology Program rodent bioassay (NTPRB) were used to identify a sample of approximately 50 rodent-tested additives and other chemicals added to food that had been evaluated independently of the FDA/food industry. Surprisingly, the sample shows more than 40% of these food chemicals to be carcinogenic in one or more rodent groups. If this percentage is extrapolated to all substances added to food in the United States, it would imply that more than 1000 of such substances are potential rodent carcinogens. The NTP and FDA test guidelines use similar, though not necessarily identical, rodent test procedures, including near lifetime exposures to the maximum tolerated dose. The FDA specifies that test chemicals should be administered by the oral route. However, the oral route includes three methods of delivering chemicals, that is, mixed in the food or water or delivered by stomach tube (gavage). The NTP data show only 1 of 18 food chemicals mixed in the food are rodent carcinogens, but 16 of 23 gavage-administered food chemicals are carcinogenic to rodents. The distribution suggests that among orally delivered chemicals, those administered in the feed will more likely prove to be noncarcinogens than chemicals given by gavage. The rodent data also reveal that effects may vary according to dose and genotype, as well as by route of administration, to further complicate extrapolation to humans

Additive Manufacturing for Affordable Rocket Engines

Science.gov (United States)

West, Brian; Robertson, Elizabeth; Osborne, Robin; Calvert, Marty

2016-01-01

Additive manufacturing (also known as 3D printing) technology has the potential to drastically reduce costs and lead times associated with the development of complex liquid rocket engine systems. NASA is using 3D printing to manufacture rocket engine components including augmented spark igniters, injectors, turbopumps, and valves. NASA is advancing the process to certify these components for flight. Success Story: MSFC has been developing rocket 3D-printing technology using the Selective Laser Melting (SLM) process. Over the last several years, NASA has built and tested several injectors and combustion chambers. Recently, MSFC has 3D printed an augmented spark igniter for potential use the RS-25 engines that will be used on the Space Launch System. The new design is expected to reduce the cost of the igniter by a factor of four. MSFC has also 3D printed and tested a liquid hydrogen turbopump for potential use on an Upper Stage Engine. Additive manufacturing of the turbopump resulted in a 45% part count reduction. To understanding how the 3D printed parts perform and to certify them for flight, MSFC built a breadboard liquid rocket engine using additive manufactured components including injectors, turbomachinery, and valves. The liquid rocket engine was tested seven times in 2016 using liquid oxygen and liquid hydrogen. In addition to exposing the hardware to harsh environments, engineers learned to design for the new manufacturing technique, taking advantage of its capabilities and gaining awareness of its limitations. Benefit: The 3D-printing technology promises reduced cost and schedule for rocket engines. Cost is a function of complexity, and the most complicated features provide the largest opportunities for cost reductions. This is especially true where brazes or welds can be eliminated. The drastic reduction in part count achievable with 3D printing creates a waterfall effect that reduces the number of processes and drawings, decreases the amount of touch

Storytelling intervention for patients with cancer: part 2--pilot testing.

Science.gov (United States)

Crogan, Neva L; Evans, Bronwynne C; Bendel, Robert

2008-03-01

To evaluate symptom reports and the impact of a nurse-led storytelling intervention in a supportive group setting on mood, stress level, coping with stress, pain, self-efficacy, and satisfaction with life in patients with cancer. Descriptive pilot project using a pretest/post-test control group. Local regional medical center in the Pacific Northwest region of the United States. Convenience sample of 10 patients with various cancer diagnoses; 7 completed the intervention. Participants were randomly assigned to a storytelling or control group. Using a tool kit generated for this project, a nurse facilitator guided storytelling group participants in 12 1.5-hour sessions. Six instruments, symptom assessments, and a retrospective physician chart review were completed for each group. Data were analyzed using repeated measures analysis of variance. Mood, stress, coping, pain, self-efficacy, and satisfaction with life. Comparison of changes in group mean scores revealed a significant decrease in anxiety in the storytelling group despite disease progression. Documentation of psychosocial symptomatology by physicians is limited; however, nursing assessments were useful in determining psychosocial status before and after the intervention. Results can be viewed only in context of a feasibility study and are not generalizable because of a limited sample size. A trained oncology nurse was able to use the storytelling intervention. Initial results are promising and warrant further study. After additional testing, the intervention could be used to enhance storytelling groups for patients with cancer or for individuals who are uncomfortable in or do not have access to storytelling groups.

A new fetal RHD genotyping test: Costs and benefits of mass testing to target antenatal anti-D prophylaxis in England and Wales

Directory of Open Access Journals (Sweden)

Osipenko Leeza

2011-01-01

Full Text Available Abstract Background Postnatal and antenatal anti-D prophylaxis have dramatically reduced maternal sensitisations and cases of rhesus disease in babies born to women with RhD negative blood group. Recent scientific advances mean that non-invasive prenatal diagnosis (NIPD, based on the presence of cell-free fetal DNA in maternal plasma, could be used to target prophylaxis on "at risk" pregnancies where the fetus is RhD positive. This paper provides the first assessment of cost-effectiveness of NIPD-targeted prophylaxis compared to current policies. Methods We conducted an economic analysis of NIPD implementation in England and Wales. Two scenarios were considered. Scenario 1 assumed that NIPD will be only used to target antenatal prophylaxis with serology tests continuing to direct post-delivery prophylaxis. In Scenario 2, NIPD would also displace postnatal serology testing if an RhD negative fetus was identified. Costs were estimated from the provider's perspective for both scenarios together with a threshold royalty fee per test. Incremental costs were compared with clinical implications. Results The basic cost of an NIPD in-house test is £16.25 per sample (excluding royalty fee. The two-dose antenatal prophylaxis policy recommended by NICE is estimated to cost the NHS £3.37 million each year. The estimated threshold royalty fee is £2.18 and £8.83 for Scenarios 1 and 2 respectively. At a £2.00 royalty fee, mass NIPD testing would produce no saving for Scenario 1 and £507,154 per annum for Scenario 2. Incremental cost-effectiveness analysis indicates that, at a test sensitivity of 99.7% and this royalty fee, NIPD testing in Scenario 2 will generate one additional sensitisation for every £9,190 saved. If a single-dose prophylaxis policy were implemented nationally, as recently recommended by NICE, Scenario 2 savings would fall. Conclusions Currently, NIPD testing to target anti-D prophylaxis is unlikely to be sufficiently cost-effective to

The financial imperative of physicians to control demand of laboratory testing.

LENUS (Irish Health Repository)

Murphy, R K J

2012-02-01

It is an integral component of doctor\\'s duty of care to understand the significant impact laboratory testing has on the expense an ultimate quality of healthcare patients receive, yet the costs of these tests are poorly perceived. Utilising semi-structured interviews and questionnaires, we assessed surgeon\\'s perceived costs of two commonly encountered clinical scenarios requiring out of hours laboratory testing. Of the 35 participants only 23.3% (n = 7) accurately estimated the overall cost. The most expensive test was "Type and Screen" at Euro 83, with 77.3% (n = 17) underestimating the cost. Non-consultant hospital doctors qualified for 3 years were more likely to underestimate on-call costs (p = 0.042). It is of utmost importance to improve the knowledge of all surgeons of the financial implications of investigations. Through education we can potentially reduce un-warranted costs and fulfill our duty of care in the most cost efficient manner.

Which physical examination tests provide clinicians with the most value when examining the shoulder? Update of a systematic review with meta-analysis of individual tests.

Science.gov (United States)

Hegedus, Eric J; Goode, Adam P; Cook, Chad E; Michener, Lori; Myer, Cortney A; Myer, Daniel M; Wright, Alexis A

2012-11-01

To update our previously published systematic review and meta-analysis by subjecting the literature on shoulder physical examination (ShPE) to careful analysis in order to determine each tests clinical utility. This review is an update of previous work, therefore the terms in the Medline and CINAHL search strategies remained the same with the exception that the search was confined to the dates November, 2006 through to February, 2012. The previous study dates were 1966 - October, 2006. Further, the original search was expanded, without date restrictions, to include two new databases: EMBASE and the Cochrane Library. The Quality Assessment of Diagnostic Accuracy Studies, version 2 (QUADAS 2) tool was used to critique the quality of each new paper. Where appropriate, data from the prior review and this review were combined to perform meta-analysis using the updated hierarchical summary receiver operating characteristic and bivariate models. Since the publication of the 2008 review, 32 additional studies were identified and critiqued. For subacromial impingement, the meta-analysis revealed that the pooled sensitivity and specificity for the Neer test was 72% and 60%, respectively, for the Hawkins-Kennedy test was 79% and 59%, respectively, and for the painful arc was 53% and 76%, respectively. Also from the meta-analysis, regarding superior labral anterior to posterior (SLAP) tears, the test with the best sensitivity (52%) was the relocation test; the test with the best specificity (95%) was Yergason's test; and the test with the best positive likelihood ratio (2.81) was the compression-rotation test. Regarding new (to this series of reviews) ShPE tests, where meta-analysis was not possible because of lack of sufficient studies or heterogeneity between studies, there are some individual tests that warrant further investigation. A highly specific test (specificity >80%, LR+ ≥ 5.0) from a low bias study is the passive distraction test for a SLAP lesion. This test may

[Interpretation and use of routine pulmonary function tests: Spirometry, static lung volumes, lung diffusion, arterial blood gas, methacholine challenge test and 6-minute walk test].

Science.gov (United States)

Bokov, P; Delclaux, C

2016-02-01

Resting pulmonary function tests (PFT) include the assessment of ventilatory capacity: spirometry (forced expiratory flows and mobilisable volumes) and static volume assessment, notably using body plethysmography. Spirometry allows the potential definition of obstructive defect, while static volume assessment allows the potential definition of restrictive defect (decrease in total lung capacity) and thoracic hyperinflation (increase in static volumes). It must be kept in mind that this evaluation is incomplete and that an assessment of ventilatory demand is often warranted, especially when facing dyspnoea: evaluation of arterial blood gas (searching for respiratory insufficiency) and measurement of the transfer coefficient of the lung, allowing with the measurement of alveolar volume to calculate the diffusing capacity of the lung for CO (DLCO: assessment of alveolar-capillary wall and capillary blood volume). All these pulmonary function tests have been the subject of an Americano-European Task force (standardisation of lung function testing) published in 2005, and translated in French in 2007. Interpretative strategies for lung function tests have been recommended, which define abnormal lung function tests using the 5th and 95th percentiles of predicted values (lower and upper limits of normal values). Thus, these recommendations need to be implemented in all pulmonary function test units. A methacholine challenge test will only be performed in the presence of an intermediate pre-test probability for asthma (diagnostic uncertainty), which is an infrequent setting. The most convenient exertional test is the 6-minute walk test that allows the assessment of walking performance, the search for arterial desaturation and the quantification of dyspnoea complaint. Copyright © 2015 Société nationale française de médecine interne (SNFMI). Published by Elsevier SAS. All rights reserved.

Using a Bedside Video-assisted Test Tube Test to Assess Stoma Viability: A Report of 4 Cases.

Science.gov (United States)

Ahmad, Sarwat; Turner, Keli; Shah, Paulesh; Diaz, Jose

2016-07-01

Mucosal discoloration of an intestinal stoma may indicate self-limited venous congestion or necrosis necessitating operative revision. A common bedside technique to assess stoma viability is the "test tube test". A clear tube is inserted into the stoma and a hand-held light is used to assess the color of the stoma. A technique (video-assisted test tube test [VATTT]) developed by the authors utilizes a standard video bronchoscope inserted into a clear plastic blood collection tube to visually inspect and assess the mucosa. This technique was evaluated in 4 patients (age range 49-72 years, all critically ill) with a discolored stoma after emergency surgery. In each case, physical exam revealed ischemic mucosa at the surface either immediately after surgery or after worsening hypotension weeks later. Serial test tube test assessments were ambiguous when trying to assess deeper mucosa. The VATTT assessment showed viable pink mucosa beneath the surface and until the fascia was revealed in 3 patients. One (1) patient had mucosal ischemia down to the fascia, which prompted operative revision of the stoma. The new stoma was assessed with a VATTT and was viable for the entire length of the stoma. VATTT provided an enhanced, magnified, and clearer way to visually assess stoma viability in the postoperative period that can be performed at the bedside with no adverse events. It may prevent unnecessary relaparotomy or enable earlier diagnosis of deep ostomy necrosis. Validity and reliability studies are warranted.

A diagnostic model incorporating P50 sensory gating and neuropsychological tests for schizophrenia.

Directory of Open Access Journals (Sweden)

Jia-Chi Shan

Full Text Available OBJECTIVES: Endophenotypes in schizophrenia research is a contemporary approach to studying this heterogeneous mental illness, and several candidate neurophysiological markers (e.g. P50 sensory gating and neuropsychological tests (e.g. Continuous Performance Test (CPT and Wisconsin Card Sorting Test (WCST have been proposed. However, the clinical utility of a single marker appears to be limited. In the present study, we aimed to construct a diagnostic model incorporating P50 sensory gating with other neuropsychological tests in order to improve the clinical utility. METHODS: We recruited clinically stable outpatients meeting DSM-IV criteria of schizophrenia and age- and gender-matched healthy controls. Participants underwent P50 sensory gating experimental sessions and batteries of neuropsychological tests, including CPT, WCST and Wechsler Adult Intelligence Scale Third Edition (WAIS-III. RESULTS: A total of 106 schizophrenia patients and 74 healthy controls were enrolled. Compared with healthy controls, the patient group had significantly a larger S2 amplitude, and thus poorer P50 gating ratio (gating ratio = S2/S1. In addition, schizophrenia patients had a poorer performance on neuropsychological tests. We then developed a diagnostic model by using multivariable logistic regression analysis to differentiate patients from healthy controls. The final model included the following covariates: abnormal P50 gating (defined as P50 gating ratio >0.4, three subscales derived from the WAIS-III (Arithmetic, Block Design, and Performance IQ, sensitivity index from CPT and smoking status. This model had an adequate accuracy (concordant percentage = 90.4%; c-statistic = 0.904; Hosmer-Lemeshow Goodness-of-Fit Test, p = 0.64>0.05. CONCLUSION: To the best of our knowledge, this is the largest study to date using P50 sensory gating in subjects of Chinese ethnicity and the first to use P50 sensory gating along with other neuropsychological tests

A randomised controlled trial of sensory awareness training and additional motor practice for learning scalpel skills in podiatry students.

Science.gov (United States)

Causby, Ryan S; McDonnell, Michelle N; Reed, Lloyd; Hillier, Susan L

2016-12-05

The process of using a scalpel, like all other motor activities, is dependent upon the successful integration of afferent (sensory), cognitive and efferent (motor) processes. During learning of these skills, even if motor practice is carefully monitored there is still an inherent risk involved. It is also possible that this strategy could reinforce high levels of anxiety experienced by the student and affect student self-efficacy, causing detrimental effects on motor learning. An alternative training strategy could be through targeting sensory rather than motor processes. Second year podiatry students who were about to commence learning scalpel skills were recruited. Participants were randomly allocated into sensory awareness training (Sensory), additional motor practice (Motor) or usual teaching only (Control) groups. Participants were then evaluated on psychological measures (Intrinsic Motivation Inventory) and dexterity measures (Purdue Pegboard, Grooved Pegboard Test and a grip-lift task). A total of 44 participants were included in the study. There were no baseline differences or significant differences between the three groups over time on the Perceived Competence, Effort/ Importance or Pressure/ Tension, psychological measures. All groups showed a significant increase in Perceived Competence over time (F 1,41  = 13.796, p = 0.001). Only one variable for the grip-lift task (Preload Duration for the non-dominant hand) showed a significant difference over time between the groups (F 2,41  = 3.280, p = 0.038), specifically, Motor and Control groups. The use of sensory awareness training, or additional motor practice did not provide a more effective alternative compared with usual teaching. Further research may be warranted using more engaged training, provision of supervision and greater participant numbers. Australian New Zealand Clinical Trials Registry (ANZCTR): ACTRN12616001428459 . Registered 13 th October 2016. Registered Retrospectively.

Biodiesel production from tall oil with synthesized Mn and Ni based additives: effects of the additives on fuel consumption and emissions

Energy Technology Data Exchange (ETDEWEB)

Ali Keskin; Metin Guru; Duran Altiparmak [Mersin University, Mersin (Turkey). Technical Education Faculty

2007-05-15

In this study, biodiesel fuel and fuel additives were produced from crude tall oil that is a by-product in the pulp manufacturing by craft or sulphate pulping process. Fatty acids and resinic acids were obtained from crude tall oil by distillation method. Tall oil methyl ester (biodiesel) was produced from fatty acids. Resinic acids were reacted with NiO and MnO{sub 2} stoichiometrically for production of metallic fuel additives. Each metallic fuel additive was added at the rate of 8 {mu}mol/l and 12 {mu}mol/l to make mixtures of 60% tall oil methyl ester/40% diesel fuel (TE60) for preparing test fuels. Metallic fuel additives improved properties of biodiesel fuels, such as pour point and viscosity values. Biodiesel fuels were tested in an unmodified direct injection diesel engine at full load condition. Specific fuel consumption of biodiesel fuels increased by 6.00%, however, in comparison with TE60, it showed trend of decreasing with adding of additives. Exhaust emission profile of biodiesel fuels improved. CO emissions and smoke opacity decreased up to 64.28% and 30.91% respectively. Low NOx emission was also observed in general for the biodiesel fuels. 28 refs., 4 figs., 3 tabs.

Characterization of PCC Cement by Addition of Napa Soil from Subdistrict Sarilamak 50 Kota District as Alternative Additional Material for Semen Padang

Science.gov (United States)

Mawardi, M.; Deyundha, D.; Zainul, R.; Zalmi P, R.

2018-04-01

The study has been conducted to determine characteristics of the portland composite cement by the addition of napa soil from Sarilamak subdistrict, 50 Kota District as an alternative additional material at PT. Semen Padang. Napa soil is a natural material highly containing silica and alumina minerals so that it can be one of material in producing cement. This study aims to determine the effect of napa soil on the quality of portland composite cement. Napa soil used in the variation compositions 0%, 4%, 8%, 12% and 16%, for control of cement used 8 % of pozzolan and 0 % of napa soil. Determination of cement quality by testing cement characteristics include blaine test, sieving, lost of ignition or LOI, insoluble residue, normal consistency, setting time and compressive strength. Cement was characterized using XRF. Fineness of cement decreases with the addition of napa soil. Lost of Ignition of cement decreased, while the insoluble residue increased with the addition of napa soil. Normal consistency of cement increasing, so does initial setting time and final setting time of cement. While the resultant compressive strength decreases with the addition of napa soil on 28 days, 342, 325, 307, 306, and 300 kg / cm2.

Warrant Officer Examinations. PR-4018

Science.gov (United States)

1944-10-10

ccouunting, Administrative - Clcorica1, Judge, Advo Ge~nc. De~ptsAdxiiniistrati~ve 1 icl Adi isrtv - Supp:ly, generaile8 ~ Administrativo ’ - Supply, Air...chronological index if action in processing special and summary records of trial. Answers teleph.’nic inquirie’s pertaining to subject matter contain- ed...reproduction by lithopraphy, black and white process printing, and gelatin duplication; moy couidinnte and supervise procurement, storage, and distribution of

Aging Influence on Fatigue Characteristics of RAC Mixtures Containing Warm Asphalt Additives

Directory of Open Access Journals (Sweden)

Feipeng Xiao

2010-01-01

Full Text Available Aging is an important factor to affect the long-term performance of asphalt pavement. The fatigue life of a typical warm mix asphalt (WMA is generally related to various factors of rheological and mechanical properties of the mixture. The study of the fatigue behavior of the specific rubberized WMA is helpful in recycling the scrap tires and saving energy in terms of the conventional laboratory aging process. This study explores the utilization of the conventional fatigue analysis approach in investigating the cumulative dissipated, stiffness, and fatigue life of rubberized asphalt concrete mixtures containing the WMA additive after a long-term aging process. The aged beams were made with one rubber type (−40 mesh ambient crumb rubber, two aggregate sources, two WMA additives (Asphamin and Sasobit, and tested at 5 and 20ºC. A total of 55 aged fatigue beams were tested in this study. The test results indicated that the addition of crumb rubber extends the fatigue resistance of asphalt binder while WMA additive exhibits a negative effect. The study indicated that the WMA additive generally has an important influence on fatigue life. In addition, test temperature and aggregate source play an important role in determining the cumulative dissipated energy, stiffness, and fatigue life of an aged mixture.

Swift and Certain, Proportionate and Consistent: Key Values of Urine Drug Test Consequences for Probationers.

Science.gov (United States)

Cadwallader, Amy B

2017-09-01

Traditionally, urine drug testing (UDT) in the correctional population (both prison and community corrections) has been infrequent, is scheduled, and has a high possibility of delayed results. Of practical relevance is that scheduled testing is ineffective for identifying drug misuse. Of ethical relevance is that consequences of positive scheduled tests can be unpredictable-in the form of overly severe punishment or a lack of treatment options-and that the scheduled testing paradigm is a poor way to change behaviors. More innovative programs now use a UDT paradigm with more frequent, random testing providing rapid results and certain, swift consequences and addiction treatment when warranted or requested. Studies have shown these new programs-the foundation of which is frequent, random UDTs-to significantly reduce drug use, criminal recidivism, and incarceration. © 2017 American Medical Association. All Rights Reserved.

Verification Test of Automated Robotic Assembly of Space Truss Structures

Science.gov (United States)

Rhodes, Marvin D.; Will, Ralph W.; Quach, Cuong C.

1995-01-01

A multidisciplinary program has been conducted at the Langley Research Center to develop operational procedures for supervised autonomous assembly of truss structures suitable for large-aperture antennas. The hardware and operations required to assemble a 102-member tetrahedral truss and attach 12 hexagonal panels were developed and evaluated. A brute-force automation approach was used to develop baseline assembly hardware and software techniques. However, as the system matured and operations were proven, upgrades were incorporated and assessed against the baseline test results. These upgrades included the use of distributed microprocessors to control dedicated end-effector operations, machine vision guidance for strut installation, and the use of an expert system-based executive-control program. This paper summarizes the developmental phases of the program, the results of several assembly tests, and a series of proposed enhancements. No problems that would preclude automated in-space assembly or truss structures have been encountered. The test system was developed at a breadboard level and continued development at an enhanced level is warranted.

Stabilization of inorganic mixed waste to pass the TCLP and STLC tests using clay and pH-insensitive additives

International Nuclear Information System (INIS)

Bowers, J.S.; Anson, J.R.; Painter, S.M.; Maitino, R.E.

1995-03-01

Stabilization traps toxic contaminants (usually both chemically and physically) in a matrix so that they do not leach into the environment. Typical contaminants are metals (mostly transition metals) that exhibit the characteristic of toxicity. The stabilization process routinely uses pozzolanic materials. Portland cement, fly ash-lime mixes, gypsum cements, and clays are some of the most common materials. In many instances, materials that can pass the Toxicity Characteristic Leaching Procedure (TCLP-the federal leach test) or the Soluble Threshold Leachate Concentration (STLC-the California leach test) must have high concentrations of lime or other caustic material because of the low pH of the leaching media. Both leaching media, California's and EPA's, have a pH of 5.0. California uses citric acid and sodium citrate while EPA uses acetic acid and sodium acetate. These media can form ligands that provide excellent metal leaching. Because of the aggressive nature of the leaching medium, stabilized wastes in many cases will not pass the leaching tests. At the Lawrence Livermore National Laboratory, additives such as dithiocarbamates and thiocarbonates, which are pH-insensitive and provide resistance to ligand formation, are used in the waste stabilization process. Attapulgite, montmorillonite, and sepiolite clays are used because they are forgiving (recipe can be adjusted before the matrix hardens). The most frequently used stabilization process consists of a customized recipe involving waste sludge, clay and dithiocarbamate salt, mixed with a double planetary mixer into a pasty consistency. TCLP and STLC data on this waste matrix have shown that the process matrix meets land disposal requirements

Space Station propulsion - Advanced development testing of the water electrolysis concept at MSFC

Science.gov (United States)

Jones, Lee W.; Bagdigian, Deborah R.

1989-01-01

The successful demonstration at Marshall Space Flight Center (MSFC) that the water electrolysis concept is sufficiently mature to warrant adopting it as the baseline propulsion design for Space Station Freedom is described. In particular, the test results demonstrated that oxygen/hydrogen thruster, using gaseous propellants, can deliver more than two million lbf-seconds of total impulse at mixture ratios of 3:1 to 8:1 without significant degradation. The results alao demonstrated succcessful end-to-end operation of an integrated water electrolysis propulsion system.

Improving Asphalt Mixtures Performance by Mitigating Oxidation Using Anti-Oxidants Additives

Science.gov (United States)

Dessouky, Samer; Diaz, Manuel

Polymer modified additives are typically used to improve rheological properties of asphalt binder as well as mechanical properties of asphalt concrete mix. In this study, polymer-modified binder PG70-22 is mixing with two co-polymers enhanced with anti-oxidant agents namely; Solution Styrene-Butadiene Rubber (SSBR) and Solution Ethylene-Butylene/Styrene (SEBS). The objective of this study is to characterize the effect of those additives into the rheological properties of the asphalt binder using temperature sweep test and mechanical properties of asphalt mixes. The aging index is determined to evaluate the role of additives to reduce brittleness after aging of the binder. The performance of asphalt mixes were characterized by Hamburg Wheel Tracking Test for moisture damage, Beam Fatigue Test for fatigue properties and Flow Number Test for rutting performance. It is found that the asphalt mixes with enhanced binders are improving its rutting and moisture resistance but decreased its fatigue life compared to the control mix.

Additives as corrosion inhibitors in reinforced concrete

International Nuclear Information System (INIS)

Venegas, Ricardo; Vera, Rosa; Carvajal, Ana Maria; Villarroel, Maria; Vera, Enrique; Ortiz, Cesar

2008-01-01

This work studies the behavior of two additives as inhibitors of corrosion in reinforced concrete. The presence of Microsilica, a physical inhibitor, in the mixture decreases pore size in structures and improves compression. Calcium Nitrite, a chemical inhibitor, is an oxidizing agent and allows a more homogenous film to form over the steel that becomes more resistant to attacks from aggressive ions like anion chloride and others. Three pairs of concrete test pieces were used without additives and with additives with a/c ration of 0.55. The samples were exposed to an accelerated attack of chlorides, submerging them in a 4.27 M solution of NaCl for 24 hours and then drying them at room temperature for another 24 hours, completing a cycle every 48 hours. The tests were carried out at 1 cycle and 5 cycles of partial moistening and drying. The steel corrosion was evaluated with corrosion potential measurements. Conductivity, pH, chlorides and sulfate profiles were defined depending on the depth of the concrete. The composition of the corrosion products was determined using X-ray diffraction and the morphology of the film by scanning electron microscopy. The results show that for 1 test cycle, the corrosion potential of the steel in the sample with calcium nitrite was -54mV, which was a higher value than that measured in the sample with microsilica (-217.3mV) and without an additive (-159.1mV), corroborating its inhibitory power. The content of the free chlorides in the sample with micros ice allows greater capillary suction by adding high amounts of chloride to the structure (2.6% on the outside up to 2.20% near the steel); while the test pieces with calcium nitrite and without an additive had concentrations lower than 2% in all the evaluated points. After five cycles of exposing the samples to the saline solution the behavior is inverted. The measures of conductivity agreed with the previous results. Meanwhile, the pH of the solutions obtained from the powder from the

Terahertz imaging and tomography as efficient instruments for testing polymer additive manufacturing objects.

Science.gov (United States)

Perraud, J B; Obaton, A F; Bou-Sleiman, J; Recur, B; Balacey, H; Darracq, F; Guillet, J P; Mounaix, P

2016-05-01

Additive manufacturing (AM) technology is not only used to make 3D objects but also for rapid prototyping. In industry and laboratories, quality controls for these objects are necessary though difficult to implement compared to classical methods of fabrication because the layer-by-layer printing allows for very complex object manufacturing that is unachievable with standard tools. Furthermore, AM can induce unknown or unexpected defects. Consequently, we demonstrate terahertz (THz) imaging as an innovative method for 2D inspection of polymer materials. Moreover, THz tomography may be considered as an alternative to x-ray tomography and cheaper 3D imaging for routine control. This paper proposes an experimental study of 3D polymer objects obtained by additive manufacturing techniques. This approach allows us to characterize defects and to control dimensions by volumetric measurements on 3D data reconstructed by tomography.

A method for additive bias correction in cross-cultural surveys

DEFF Research Database (Denmark)

Scholderer, Joachim; Grunert, Klaus G.; Brunsø, Karen

2001-01-01

additive bias from cross-cultural data. The procedure involves four steps: (1) embed a potentially biased item in a factor-analytic measurement model, (2) test for the existence of additive bias between populations, (3) use the factor-analytic model to estimate the magnitude of the bias, and (4) replace......Measurement bias in cross-cultural surveys can seriously threaten the validity of hypothesis tests. Direct comparisons of means depend on the assumption that differences in observed variables reflect differences in the underlying constructs, and not an additive bias that may be caused by cultural...... differences in the understanding of item wording or response category labels. However, experience suggests that additive bias can be found more often than not. Based on the concept of partial measurement invariance (Byrne, Shavelson and Muthén, 1989), the present paper develops a procedure for eliminating...

Establishing placement test fit and performance: Serving local needs

Directory of Open Access Journals (Sweden)

Gerriet Janssens

2013-07-01

Full Text Available Accountability in language education is often associated with top-down national policies unresponsive—or even hostile to—local needs; however, when accountability is driven by local stakeholders seeking to better understand and enhance their programs, it can foster productive cycles of action research and curriculum development. This paper reports on one such internally-motivated accountability effort, in which program insiders sought to determine the efficacy of a reading test being administered to a new population of students at one Colombian university. Descriptive statistics, reliability estimates, and item facility and discrimination measures were used to determine whether this test was sufficiently reliable and appropriately matched to test takers’ ability in order to warrant its use as part of a high-stakes English-language placement exam. A detailed analysis of this test is used not only to propose specific recommendations for revision but also to illustrate a useful set of statistical tools appropriate for test analysis in other language programs. Moreover, we conclude that the involvement of local instructors as part of an iterative, self-reflective, test development process provides opportunities for professional development and deeper engagement in accountability projects.

Symmetry warrants rational cooperation by co-action in Social Dilemmas.

Science.gov (United States)

Sasidevan, V; Sinha, Sitabhra

2015-08-12

Is it rational for selfish individuals to cooperate? The conventional answer based on analysis of games such as the Prisoners Dilemma (PD) is that it is not, even though mutual cooperation results in a better outcome for all. This incompatibility between individual rationality and collective benefit lies at the heart of questions about the evolution of cooperation, as illustrated by PD and similar games. Here, we argue that this apparent incompatibility is due to an inconsistency in the standard Nash framework for analyzing non-cooperative games and propose a new paradigm, that of the co-action equilibrium. As in the Nash solution, agents know that others are just as rational as them and taking this into account lead them to realize that others will independently adopt the same strategy, in contrast to the idea of unilateral deviation central to Nash equilibrium thinking. Co-action equilibrium results in better collective outcomes for games representing social dilemmas, with relatively "nicer" strategies being chosen by rational selfish individuals. In particular, the dilemma of PD gets resolved within this framework, suggesting that cooperation can evolve in nature as the rational outcome even for selfish agents, without having to take recourse to additional mechanisms for promoting it.

Determination of the availability of appropriate aged flight rocket motors. [captive tests to determine case bond separation and grain bore cracking

Science.gov (United States)

Martin, P. J.

1974-01-01

A program to identify surplus solid rocket propellant engines which would be available for a program of functional integrity testing was conducted. The engines are classified as: (1) upper stage and apogee engines, (2) sounding rocket and launch vehicle engines, and (3) jato, sled, and tactical engines. Nearly all the engines were available because their age exceeds the warranted shelf life. The preference for testing included tests at nominal flight conditions, at design limits, and to establish margin limits. The principal failure modes of interest were case bond separation and grain bore cracking. Data concerning the identification and characteristics of each engine are tabulated. Methods for conducting the tests are described.

34 CFR 668.148 - Additional criteria for the approval of certain tests.

Science.gov (United States)

2010-07-01

... the mean score and standard deviation for Spanish-speaking students with high school diplomas who have... guidelines provided in the 1985 edition of the “Testing Linguistic Minorities” section of the Standards for... the American Educational Research Association, the American Psychological Association, and the...

Characterization of the Tribological Behavior of Graphene-Based Additives

Energy Technology Data Exchange (ETDEWEB)

Erck, Robert

2014-09-01

XG-supplied nanocrystalline additives were extensively tested for friction and wear behavior. A technique for investigating the stability of additives was developed, and a report covered filtration and centrifugation methods for settling and filterable content. Friction and wear trends in partially and fully formulated oils were reported. Particle size analysis was performed and reported.

Effect of additional speed endurance training on performance and muscle adaptations

DEFF Research Database (Denmark)

Gunnarsson, Thomas; Christensen, Peter Møller; Holse, Kris

2012-01-01

PURPOSE: The present study examined the effect of additional speed-endurance training during the season on muscle adaptations and performance of trained soccer players. METHODS: Eighteen sub-elite soccer players performed one session with 6-9 30-s intervals at an intensity of 90-95 % ofmaximal...... intensity (speed endurance training; SET) a week for 5 weeks (SET-intervention). Before and after the SET-intervention the players carried out the Yo-Yo intermittent recovery level 2 (Yo- Yo IR2) test, a sprint test (10- and 30-m) and an agility test. In addition, seven of the players had a resting muscle...

Co-occurring nonnative woody shrubs have additive and non-additive soil legacies.

Science.gov (United States)

Kuebbing, Sara E; Patterson, Courtney M; Classen, Aimée T; Simberloff, Daniel

2016-09-01

To maximize limited conservation funds and prioritize management projects that are likely to succeed, accurate assessment of invasive nonnative species impacts is essential. A common challenge to prioritization is a limited knowledge of the difference between the impacts of a single nonnative species compared to the impacts of nonnative species when they co-occur, and in particular predicting when impacts of co-occurring nonnative species will be non-additive. Understanding non-additivity is important for management decisions because the management of only one co-occurring invader will not necessarily lead to a predictable reduction in the impact or growth of the other nonnative plant. Nonnative plants are frequently associated with changes in soil biotic and abiotic characteristics, which lead to plant-soil interactions that influence the performance of other species grown in those soils. Whether co-occurring nonnative plants alter soil properties additively or non-additively relative to their effects on soils when they grow in monoculture is rarely addressed. We use a greenhouse plant-soil feedback experiment to test for non-additive soil impacts of two common invasive nonnative woody shrubs, Lonicera maackii and Ligustrum sinense, in deciduous forests of the southeastern United States. We measured the performance of each nonnative shrub, a native herbaceous community, and a nonnative woody vine in soils conditioned by each shrub singly or together in polyculture. Soils conditioned by both nonnative shrubs had non-additive impacts on native and nonnative performance. Root mass of the native herbaceous community was 1.5 times lower and the root mass of the nonnative L. sinense was 1.8 times higher in soils conditioned by both L. maackii and L. sinense than expected based upon growth in soils conditioned by either shrub singly. This result indicates that when these two nonnative shrubs co-occur, their influence on soils disproportionally favors persistence

Built-In Test Engine For Memory Test

OpenAIRE

McEvoy, Paul; Farrell, Ronan

2004-01-01

In this paper we will present an on-chip method for testing high performance memory devices, that occupies minimal area and retains full flexibility. This is achieved through microcode test instructions and the associated on-chip state machine. In addition, the proposed methodology will enable at-speed testing of memory devices. The relevancy of this work is placed in context with an introduction to memory testing and the techniques and algorithms generally used today.

Additive Manufactured Coronagraph Bench for Detection of Exoplanets

Data.gov (United States)

National Aeronautics and Space Administration — We propose to use additive manufacturing (AM) to build a Coronagraph Bench engineering test unit.  The versatility inherent in the 3D-printing process allows for a...

30 CFR 18.32 - Fastenings-additional requirements.

Science.gov (United States)

2010-07-01

... and Design Requirements § 18.32 Fastenings—additional requirements. (a) Bolts, screws, or studs shall...) Lockwashers shall be provided for all bolts, screws, and studs that secure parts of explosion-proof enclosures... conduct explosion tests with standard bolts, nuts, cap screws, or studs substituted for any special high...

A manual on using additives

International Nuclear Information System (INIS)

Lee, Bong Hoon

1991-10-01

This book consists of five chapters, which describe plasticizer ; summary, synthesis of plasticizer, basic notion, analysis and test on plasticizer, stabilizer ; stabilizer for plastic, an antioxidant, phosphorous acid estelle, ultraviolet ray absorbent, performance of stabilizer, influence on another additives, mix case of PVC production and analysis method for stabilizer, ultraviolet ray absorbent ; basic property and ultraviolet ray absorbent maker, anti-static agent ; basics, anti-static agent of a high molecule and analysis of anti-static agent, flame retardant of plastic.

Evaluation of Additive Manufacturing for Composite Part Molds

Energy Technology Data Exchange (ETDEWEB)

Duty, Chad E. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Springfield, Robert M. [Tru Design, LLC, Knoxville, TN (United States)

2015-02-01

The ORNL Manufacturing Demonstration Facility (MDF) collaborated with Tru-Design to test the quality and durability of molds used for making fiber reinforced composites using additive manufacturing. The partners developed surface treatment techniques including epoxy coatings and machining to improve the quality of the surface finish. Test samples made using the printed and surface finished molds demonstrated life spans suitable for one-of-a-kind and low-volume applications, meeting the project objective.

Advantages and disadvantages of technologies for HER2 testing in breast cancer specimens.

Science.gov (United States)

Furrer, Daniela; Sanschagrin, François; Jacob, Simon; Diorio, Caroline

2015-11-01

Human epidermal growth factor receptor 2 (HER2) plays a central role as a prognostic and predictive marker in breast cancer specimens. Reliable HER2 evaluation is central to determine the eligibility of patients with breast cancer to targeted anti-HER2 therapies such as trastuzumab and lapatinib. Presently, several methods exist for the determination of HER2 status at different levels (protein, RNA, and DNA level). In this review, we discuss the main advantages and disadvantages of the techniques developed so far for the evaluation of HER2 status in breast cancer specimens. Each technique has its own advantages and disadvantages. It is therefore not surprising that no consensus has been reached so far on which technique is the best for the determination of HER2 status. Currently, emphasis must be put on standardization of procedures, internal and external quality control assessment, and competency evaluation of already existing methods to ensure accurate, reliable, and clinically meaningful test results. Development of new robust and accurate diagnostic assays should also be encouraged. In addition, large clinical trials are warranted to identify the technique that most reliably predicts a positive response to anti-HER2 drugs. Copyright© by the American Society for Clinical Pathology.

A procedure for eliminating additive bias from cross-cultural survey data

DEFF Research Database (Denmark)

Scholderer, Joachim; Grunert, Klaus G.; Brunsø, Karen

2005-01-01

additive bias from cross-cultural data. The procedure involves four steps: (1) embed a potentially biased item in a factor-analytic measurement model, (2) test for the existence of additive bias between populations, (3) use the factor-analytic model to estimate the magnitude of the bias, and (4) replace......Measurement bias in cross-cultural surveys can seriously threaten the validity of hypothesis tests. Direct comparisons of means depend on the assumption that differences in observed variables reflect differences in the underlying constructs, and not an additive bias that may be caused by cultural...... differences in the understanding of item wording or response category labels. However, experience suggests that additive bias can be found more often than not. Based on the concept of partial measurement invariance (Byrne, Shavelson and Muthén 1989), the present paper develops a procedure for eliminating...

Effect of addition of yohimbine (alpha-2-receptor antagonist) to the antidepressant activity of fluoxetine or venlafaxine in the mouse forced swim test.

Science.gov (United States)

Dhir, Ashish; Kulkarni, S K

2007-01-01

Studies have suggested that alpha(2)-adrenoceptors strongly affect monoaminergic neurotransmission by enhancing not only noradrenergic but also serotonergic firing rates. With this background in mind, the present study was undertaken to monitor the effect of addition of yohimbine (alpha(2)-adrenoceptor antagonist) to the effect of fluoxetine (selective serotonin reuptake inhibitor) or venlafaxine (dual reuptake inhibitors of both serotonin and norepinephrine) in Porsolt's forced swim test (FST) using male Laca strain mice. The immobility period was recorded in mouse FST during a 6-min period. Different doses of fluoxetine or venlafaxine were administered 30 min before exposing the animals to the test procedure. In the combination study, yohimbine (2 mg/kg i.p.) was administered 15 min before the administration of different doses of fluoxetine or venlafaxine. Fluoxetine (5, 10, 20 and 40 mg/kg) [F = 28.352] or venlafaxine (2, 4, 8 and 16 mg/kg) [F = 17.842] dose-dependently inhibited the immobility period in mice. Addition of yohimbine (2 mg/kg i.p.) potentiated the antidepressant action of fluoxetine or venlafaxine in mouse FST as the animals showed a decrease in the immobility period compared to the fluoxetine or venlafaxine per se group, respectively. The present study not only demonstrated the association of alpha(2)-receptors in the antidepressant effect of fluoxetine or venlafaxine, but also supports its adjuvant therapy with other antidepressant drugs. (c) 2007 S. Karger AG, Basel.

SLM processing-microstructure-mechanical property correlation in an aluminum alloy produced by additive manufacturing

Science.gov (United States)

Alejos, Martin Fernando

Additive manufacturing has become a highly researched topic in recent years all over the world. The current research evaluates the merits of additive manufacturing based on the mechanical, microstructural, and fracture properties of additive manufactured AlSi10Mg test specimens. The additive manufactured build plates consisted of tensile and fatigue test specimens. They were printed in the 0°, 30°, 60°, and 90° orientations relative to the build platform. Tensile and dynamic fatigue tests were conducted followed by microstructural characterization and fracture analysis. A wrought 6061 T6 aluminum alloy was also tested for comparison. Tensile tests revealed similar ultimate tensile strengths for all aluminum tensile specimens (350-380 MPa). Fatigue strength was greatest for wrought 6061 T6 aluminum (175 MPa). The fatigue behavior was a strong function of build orientation for the additive manufactured specimens. The 0°, 30°, and 60° orientations had fatigue strengths close to 104 MPa while the 90° orientation had a fatigue strength of 125 MPa. All test specimens failed primarily in a ductile manner. The effect of laser power, hatch spacing, and scan speed were also studied using microstructural analysis. Increasing laser power decreased grain size and void size. Increasing scan speed led to the formation of columnar grains. Increasing hatch spacing decreased grain size and the amount of voids present in the microstructure.

Survey of active and inactive mines for possible use as in situ test facilities

International Nuclear Information System (INIS)

1976-09-01

A survey of active and inactive mines which might be useful for radioactive waste storage in situ test experiments was conducted. It was performed for Union Carbide Corporation, Nuclear Division, Office of Waste Isolation. The report covers available information gathered from literature, U.S. Bureau of Mines, the Mining Enforcement and Safety Agency, and a limited number of personal contacts with constructors or operators of facilities. This survey is preliminary in nature and the objective is to develop potential candidate facilities for in situ experiments which warrant further investigation. Included are descriptions of 244 facilities, with all the data about each one which was available within the time restraint of the study. These facility descriptions are additionally indexed by depth of mine, nature of the country rock, mineral mined, and type of entry. A total of 14 inactive mines and 34 active mines has been selected as those most worthy of further investigation for possible service as nuclear waste isolation test facilities. This investigation, being preliminary and having been performed in a very short time period, must be qualified, and the description of the qualification is presented in the body of this report. Qualifications deal primarily with the hazard of having omitted facilities and having incomplete data in some instances. Results indicate sedimentary rock mines of minerals of evaporite origin as a first ranking of preference for in situ testing, followed by other sedimentary rocks and then by mines producing minerals from any type rock where the mine is above the local water table. These are general rules and of course there can be exceptions to them

Reliability of the Timed Up and Go test and Ten-Metre Timed Walk Test in Pregnant Women with Pelvic Girdle Pain.

Science.gov (United States)

Evensen, Natalie M; Kvåle, Alice; Braekken, Ingeborg H

2015-09-01

There is a lack of functional objective tests available to measure functional status in women with pelvic girdle pain (PGP). The purpose of this study was to establish test-retest and intertester reliability of the Timed Up and Go (TUG) test and Ten-metre Timed Walk Test (10mTWT) in pregnant women with PGP. A convenience sample of women was recruited over a 4-month period and tested on two occasions, 1 week apart to determine test-retest reliability. Intertester reliability was established between two assessors at the first testing session. Subjects were instructed to undertake the TUG and 10mTWT at maximum speed. One practise trial and two timed trials for each walking test was undertaken on Day 1 and one practise trial and one timed trial on Day 2. Seventeen women with PGP aged 31.1 years (SD [standard deviation] = 2.3) and 28.7 weeks pregnant (SD = 7.4) completed gait testing. Test-retest reliability using the intraclass correlation coefficient (ICC) was excellent for the TUG (0.88) and good for the 10mTWT (0.74). Intertester reliability was determined in the first 13 participants with excellent ICC values being found for both walking tests (TUG: 0.95; 10mTWT: 0.94). This study demonstrated that the TUG and 10mTWT undertaken at fast pace are reliable, objective functional tests in pregnant women with PGP. While both tests are suitable for use in the clinical and research settings, we would recommend the TUG given the findings of higher test-retest reliability and as this test requires less space and time to set up and score. Future studies in a larger sample size are warranted to confirm the results of this study. Copyright © 2015 John Wiley & Sons, Ltd.

Approach/avoidance motives, test emotions, and emotional regulation related to testing.

Science.gov (United States)

Schutz, Paul A; Benson, Jeri; Decuir-Gunby, Jessica T

2008-07-01

This research stems from our program of work that focuses on understanding how students regulated their emotions related to testing. The primary goal for this study was to incorporate the approach/ avoidance motives into a model of emotional regulation related to testing. In addition, a secondary goal was to report on efforts at construct validation of the scores obtained during the refinement of the Emotional Regulation Related to Testing (ERT) Scale. Our results suggest that underlying beliefs, such as approach/avoid motives and the cognitive-appraisal process, of the ERT had both direct and indirect effects to both pleasant and unpleasant emotions related to testing. In addition, the ERT accounted for 56% of the variance in Pleasant and 87% of Unpleasant Test Emotions.

Early hydration of portland cement with crystalline mineral additions

International Nuclear Information System (INIS)

Rahhal, V.; Talero, R.

2005-01-01

This research presents the effects of finely divided crystalline mineral additions (quartz and limestone), commonly known as filler, on the early hydration of portland cements with very different mineralogical composition. The used techniques to study the early hydration of blended cements were conduction calorimeter, hydraulicity (Fratini's test), non-evaporable water and X-ray diffraction. Results showed that the stimulation and the dilution effects increase when the percentage of crystalline mineral additions used is increased. Depending on the replacement proportion, the mineralogical cement composition and the type of crystalline addition, at 2 days, the prevalence of the dilution effect or the stimulation effect shows that crystalline mineral additions could act as sites of heat dissipation or heat stimulation, respectively

Additives for rapeseed oil fuel. Influence on the exhaust gas emissions

Energy Technology Data Exchange (ETDEWEB)

Kastl, Johannes; Remmele, Edgar; Thuneke, Klaus [Technologie- und Foerderzentrum, Straubing (Germany)

2013-06-01

In contrast to fossil diesel fuel, the use of additives is not common in rapeseed oil fuel. In a preceding research project the efficacy of several additives, that are commercially available for the use in fossil diesel or FAME, has been investigated for rapeseed oil fuel in the lab. Four additives could be identified, which have a significant influence on the ignition delay or the low temperature flow behaviour of rapeseed oil fuel. To investigate whether there are negative effects of the additives on other fuel-related properties in practical use, a test series on an agricultural tractor capable of running on vegetable oils has been conducted. Attention is focused on the operating parameters like power, torque or fuel consumption as well as on regulated emissions (CO, HC, particulate matter or NOx) and non-regulated emissions like polycyclic aromatic hydrocarbons. Additionally, the influence of the additives on the storage stability of rapeseed oil fuel is investigated in long term studies. No negative influence of the additives on the regulated emissions could be seen in the experiments, the data of the non-regulated emissions is still being analysed. This paper will focus on the emissions testing; results of the long term studies will be given in the presentation. (orig.)

LONG-TERM DEMONSTRATION OF SORBENT ENHANCEMENT ADDITIVE TECHNOLOGY FOR MERCURY CONTROL

Energy Technology Data Exchange (ETDEWEB)

Jason D. Laumb; Dennis L. Laudal; Grant E. Dunham; John P. Kay; Christopher L. Martin; Jeffrey S. Thompson; Nicholas B. Lentz; Alexander Azenkeng; Kevin C. Galbreath; Lucinda L. Hamre

2011-05-27

Long-term demonstration tests of advanced sorbent enhancement additive (SEA) technologies have been completed at five coal-fired power plants. The targeted removal rate was 90% from baseline conditions at all five stations. The plants included Hawthorn Unit 5, Mill Creek Unit 4, San Miguel Unit 1, Centralia Unit 2, and Hoot Lake Unit 2. The materials tested included powdered activated carbon, treated carbon, scrubber additives, and SEAs. In only one case (San Miguel) was >90% removal not attainable. The reemission of mercury from the scrubber at this facility prevented >90% capture.

Anomaly Detection In Additively Manufactured Parts Using Laser Doppler Vibrometery

Energy Technology Data Exchange (ETDEWEB)

Hernandez, Carlos A. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

2015-09-29

Additively manufactured parts are susceptible to non-uniform structure caused by the unique manufacturing process. This can lead to structural weakness or catastrophic failure. Using laser Doppler vibrometry and frequency response analysis, non-contact detection of anomalies in additively manufactured parts may be possible. Preliminary tests show promise for small scale detection, but more future work is necessary.

A Fully Nonmetallic Gas Turbine Engine Enabled by Additive Manufacturing, Part II: Additive Manufacturing and Characterization of Polymer Composites

Science.gov (United States)

Chuang, Kathy C.; Grady, Joseph E.; Arnold, Steven M.; Draper, Robert D.; Shin, Eugene; Patterson, Clark; Santelle, Tom; Lao, Chao; Rhein, Morgan; Mehl, Jeremy

2015-01-01

This publication is the second part of the three part report of the project entitled "A Fully Nonmetallic Gas Turbine Engine Enabled by Additive Manufacturing" funded by NASA Aeronautics Research Institute (NARI). The objective of this project was to conduct additive manufacturing to produce aircraft engine components by Fused Deposition Modeling (FDM), using commercially available polyetherimides-Ultem 9085 and experimental Ultem 1000 mixed with 10% chopped carbon fiber. A property comparison between FDM-printed and injection molded coupons for Ultem 9085, Ultem 1000 resin and the fiber-filled composite Ultem 1000 was carried out. Furthermore, an acoustic liner was printed from Ultem 9085 simulating conventional honeycomb structured liners and tested in a wind tunnel. Composite compressor inlet guide vanes were also printed using fiber-filled Ultem 1000 filaments and tested in a cascade rig. The fiber-filled Ultem 1000 filaments and composite vanes were characterized by scanning electron microscope (SEM) and acid digestion to determine the porosity of FDM-printed articles which ranged from 25 to 31%. Coupons of Ultem 9085, experimental Ultem 1000 composites and XH6050 resin were tested at room temperature and 400F to evaluate their corresponding mechanical properties. A preliminary modeling was also initiated to predict the mechanical properties of FDM-printed Ultem 9085 coupons in relation to varied raster angles and void contents, using the GRC-developed MAC/GMC program.

Automated nucleic acid amplification testing in blood banks: An additional layer of blood safety

Directory of Open Access Journals (Sweden)

Pragati Chigurupati

2015-01-01

Full Text Available Context: A total of 30 million blood components are transfused each year in India. Blood safety thus becomes a top priority, especially with a population of around 1.23 billion and a high prevalence rate of human immunodeficiency virus (HIV, hepatitis B virus (HBV and hepatitis C virus (HCV in general population. Nucleic acid amplification testing (NAT in blood donor screening has been implemented in many developed countries to reduce the risk of transfusion-transmitted viral infections (TTIs. NAT takes care of the dynamics of window period of viruses and offers the safest blood pack for donation. Aims: The aim of this study is to show the value of NAT in blood screening. Settings and Design: Dhanavantari Blood Bank, Rajahmundry, Andhra Pradesh, India. Subjects and Methods: Over a period of 1 year from January 2012 to December 2012, a total number of 15,000 blood donor samples were subjected to tests for HIV, HBV, and HCV by enzyme-linked immunosorbent assay (ELISA method and 8000 ELISA nonreactive samples were subjected for NAT using multiplex polymerase chain reaction technology. Results: Of the 15,000 donors tested, 525 were seroreactive. In 8000 ELISA negative blood samples subjected to NAT, 4 donor samples were reactive for HBV. The NAT yield was 1 in 2000. Conclusions: NAT could detect HIV, HBV, and HCV cases in blood donor samples those were undetected by serological tests. NAT could interdict 2500 infectious donations among our approximate 5 million annual blood donations.

Ammonium fluoride as a mobile phase additive in aqueous normal phase chromatography.

Science.gov (United States)

Pesek, Joseph J; Matyska, Maria T

2015-07-03

The use of ammonium fluoride as a mobile phase additive in aqueous normal phase chromatography with silica hydride-based stationary phases and mass spectrometry detection is evaluated. Retention times, peak shape, efficiency and peak intensity are compared to the more standard additives formic acid and ammonium formate. The test solutes were NAD, 3-hydroxyglutaric acid, α-ketoglutaric acid, p-aminohippuric acid, AMP, ATP, aconitic acid, threonine, N-acetyl carnitine, and 3-methyladipic acid. The column parameters are assessed in both the positive and negative ion detection modes. Ammonium fluoride is potentially an aggressive mobile phase additive that could have detrimental effects on column lifetime. Column reproducibility is measured and the effects of switching between different additives are also tested. Copyright © 2015 Elsevier B.V. All rights reserved.

Minimizing the Moisture Damage and Drain down of Iraqi SMA Mixtures Using Waste Additives

Directory of Open Access Journals (Sweden)

Ali Al-Hadidy

2013-04-01

Full Text Available This research deals with the viability of using polyester fiber (PF, crumb rubber tire (CRT and cellulose fiber (CF as stabilizing waste additives in producing Iraqi SMA mixtures that sustain drain down phenomenon and moisture damage sensitivity. Different ratios of these additives (0.1, 0.2, and 0.3% by weight of aggregate and filler were mixed with 40/50 paving asphalt by means of dry process. Unmodified and modified SMA mixtures were subjected to drain down, Marshall, static indirect tensile strength, tensile stiffness modulus, static compressive strength, tensile strength ratio and index of retained strength tests. A set of regression equations between these tests were established. In addition, an optimization table based on these tests, which can be used to select the type or amount of additive for any field applications has been determined and reported. The results indicated that the inclusion of these additives in SMA mixtures can satisfy the performance requirement of high temperature and much rain zone.

Biocompatibility of hydroxyapatite scaffolds processed by lithography-based additive manufacturing.

Science.gov (United States)

Tesavibul, Passakorn; Chantaweroad, Surapol; Laohaprapanon, Apinya; Channasanon, Somruethai; Uppanan, Paweena; Tanodekaew, Siriporn; Chalermkarnnon, Prasert; Sitthiseripratip, Kriskrai

2015-01-01

The fabrication of hydroxyapatite scaffolds for bone tissue engineering applications by using lithography-based additive manufacturing techniques has been introduced due to the abilities to control porous structures with suitable resolutions. In this research, the use of hydroxyapatite cellular structures, which are processed by lithography-based additive manufacturing machine, as a bone tissue engineering scaffold was investigated. The utilization of digital light processing system for additive manufacturing machine in laboratory scale was performed in order to fabricate the hydroxyapatite scaffold, of which biocompatibilities were eventually evaluated by direct contact and cell-culturing tests. In addition, the density and compressive strength of the scaffolds were also characterized. The results show that the hydroxyapatite scaffold at 77% of porosity with 91% of theoretical density and 0.36 MPa of the compressive strength are able to be processed. In comparison with a conventionally sintered hydroxyapatite, the scaffold did not present any cytotoxic signs while the viability of cells at 95.1% was reported. After 14 days of cell-culturing tests, the scaffold was able to be attached by pre-osteoblasts (MC3T3-E1) leading to cell proliferation and differentiation. The hydroxyapatite scaffold for bone tissue engineering was able to be processed by the lithography-based additive manufacturing machine while the biocompatibilities were also confirmed.

Urine Test Strips to Exclude Cerebral Spinal Fluid Blood

Directory of Open Access Journals (Sweden)

Marshall, Robin A

2011-02-01

Full Text Available Introduction: Determining the presence or absence of red blood cells (RBC or their breakdown products in cerebrospinal fluid (CSF is essential for the evaluation of subarachnoid hemorrhage (SAH in headache patients. Current methodology for finding blood in the CSF is either spectrophotometric detection of pigment, which is time consuming and labor intensive, or visual assesment of samples for color change (xanthochromia, which is inaccurate. Bayer Multistix® urine test strips are designed to test urine for RBC by detecting the presence of hemoglobin. The aim of this pilot study was to evaluate the perfomance of urine reagent test strips for ruling out the presence of RBC in CSF.Methods: We compared color changes on Multistix® urine test strips to the standard of spectrophotometric absorbtion at 415nm and initial RBC counts in 138 visually clear CSF samples.Results: We performed Pearson Chi-Square and likelihood ratios on the results and found a correlation between a negative result on the urine test strip and less than 5 RBC per high power field and a spectrophotometric absorbance of less than 0.02% at 415nm in a CSF sample.Conclusion: These results warrant further investigation in the form of a prospective clinical validation as it may alter the emergency department evaluation for SAH. [West J Emerg Med. 2011;12(1:63-66.

Large animal and primate models of spinal cord injury for the testing of novel therapies.

Science.gov (United States)

Kwon, Brian K; Streijger, Femke; Hill, Caitlin E; Anderson, Aileen J; Bacon, Mark; Beattie, Michael S; Blesch, Armin; Bradbury, Elizabeth J; Brown, Arthur; Bresnahan, Jacqueline C; Case, Casey C; Colburn, Raymond W; David, Samuel; Fawcett, James W; Ferguson, Adam R; Fischer, Itzhak; Floyd, Candace L; Gensel, John C; Houle, John D; Jakeman, Lyn B; Jeffery, Nick D; Jones, Linda Ann Truett; Kleitman, Naomi; Kocsis, Jeffery; Lu, Paul; Magnuson, David S K; Marsala, Martin; Moore, Simon W; Mothe, Andrea J; Oudega, Martin; Plant, Giles W; Rabchevsky, Alexander Sasha; Schwab, Jan M; Silver, Jerry; Steward, Oswald; Xu, Xiao-Ming; Guest, James D; Tetzlaff, Wolfram

2015-07-01

Large animal and primate models of spinal cord injury (SCI) are being increasingly utilized for the testing of novel therapies. While these represent intermediary animal species between rodents and humans and offer the opportunity to pose unique research questions prior to clinical trials, the role that such large animal and primate models should play in the translational pipeline is unclear. In this initiative we engaged members of the SCI research community in a questionnaire and round-table focus group discussion around the use of such models. Forty-one SCI researchers from academia, industry, and granting agencies were asked to complete a questionnaire about their opinion regarding the use of large animal and primate models in the context of testing novel therapeutics. The questions centered around how large animal and primate models of SCI would be best utilized in the spectrum of preclinical testing, and how much testing in rodent models was warranted before employing these models. Further questions were posed at a focus group meeting attended by the respondents. The group generally felt that large animal and primate models of SCI serve a potentially useful role in the translational pipeline for novel therapies, and that the rational use of these models would depend on the type of therapy and specific research question being addressed. While testing within these models should not be mandatory, the detection of beneficial effects using these models lends additional support for translating a therapy to humans. These models provides an opportunity to evaluate and refine surgical procedures prior to use in humans, and safety and bio-distribution in a spinal cord more similar in size and anatomy to that of humans. Our results reveal that while many feel that these models are valuable in the testing of novel therapies, important questions remain unanswered about how they should be used and how data derived from them should be interpreted. Copyright © 2015 Elsevier

Nondestructive Testing

Energy Technology Data Exchange (ETDEWEB)

Berger, Harold [Argonne National Laboratory

1969-01-01

A nondestructive test is an examination of an object in any manner which will not impair the future usefulness of the object. This booklet discusses a few basic methods of nondestructive testing, and some of their characteristics. In addition, it discusses possible future methods for nondestructive testing by taking a quick look at some of the methods now under study.

Enriching Addition and Subtraction Fact Mastery through Games

Science.gov (United States)

Bay-Williams, Jennifer M.; Kling, Gina

2014-01-01

The learning of "basic facts"--single-digit combinations for addition, subtraction, multiplication, and division--has long been a focus of elementary school mathematics. Many people remember completing endless worksheets, timed tests, and flash card drills as they attempted to "master" their basic facts as children. However,…

West Nile Virus: High Transmission Rate in North-Western European Mosquitoes Indicates Its Epidemic Potential and Warrants Increased Surveillance.

Directory of Open Access Journals (Sweden)

Jelke J Fros

Full Text Available West Nile virus (WNV is a highly pathogenic flavivirus transmitted by Culex spp. mosquitoes. In North America (NA, lineage 1 WNV caused the largest outbreak of neuroinvasive disease to date, while a novel pathogenic lineage 2 strain circulates in southern Europe. To estimate WNV lineage 2 epidemic potential it is paramount to know if mosquitoes from currently WNV-free areas can support further spread of this epidemic.We assessed WNV vector competence of Culex pipiens mosquitoes originating from north-western Europe (NWE in direct comparison with those from NA. We exposed mosquitoes to infectious blood meals of lineage 1 or 2 WNV and determined the infection and transmission rates. We explored reasons for vector competence differences by comparing intrathoracic injection versus blood meal infection, and we investigated the influence of temperature. We found that NWE mosquitoes are highly competent for both WNV lineages, with transmission rates up to 25%. Compared to NA mosquitoes, transmission rates for lineage 2 WNV were significantly elevated in NWE mosquitoes due to better virus dissemination from the midgut and a shorter extrinsic incubation time. WNV infection rates further increased with temperature increase.Our study provides experimental evidence to indicate markedly different risk levels between both continents for lineage 2 WNV transmission and suggests a degree of genotype-genotype specificity in the interaction between virus and vector. Our experiments with varying temperatures explain the current localized WNV activity in southern Europe, yet imply further epidemic spread throughout NWE during periods with favourable climatic conditions. This emphasizes the need for intensified surveillance of virus activity in current WNV disease-free regions and warrants increased awareness in clinics throughout Europe.

Hypervelocity Impact Testing of Materials for Additive Construction: Applications on Earth, the Moon, and Mars

Science.gov (United States)

Ordonez, Erick; Edmunson, Jennifer; Fiske, Michael; Christiansen, Eric; Miller, Josh; Davis, Bruce Alan; Read, Jon; Johnston, Mallory; Fikes, John

2017-01-01

Additive Construction is the process of building infrastructure such as habitats, garages, roads, berms, etcetera layer by layer (3D printing). The National Aeronautics and Space Administration (NASA) and the United States Army Corps of Engineers (USACE) are pursuing additive construction to build structures using resources available in-situ. Using materials available in-situ reduces the cost of planetary missions and operations in theater. The NASA team is investigating multiple binders that can be produced on planetary surfaces, including the magnesium oxide-based Sorel cement; the components required to make Ordinary Portland Cement (OPC), the common cement used on Earth, have been found on Mars. The availability of OPC-based concrete on Earth drove the USACE to pursue additive construction for base housing and barriers for military operations. Planetary and military base structures must be capable of resisting micrometeoroid impacts with velocities ranging from 11 to 72km/s for particle sizes 200 micrometers or more (depending on protection requirements) as well as bullets and shrapnel with a velocity of 1.036km/s with projectiles 5.66mm diameter and 57.40mm in length, respectively.

Comparative analysis of compressive strength tests at age of 28 and 90 days and density of products using chemical additives in cementing radioactive waste

International Nuclear Information System (INIS)

Vieira, Vanessa Mota; Tello, Cledola Cassia Oliveira de

2013-01-01

In this research it has been studied the effects of chemical additives (admixtures) in the cementation process of radioactive wastes, which are used to improve the properties of waste cementation process, both of the paste and of the solidified product. However there are a large variety of these materials that are frequently changed or taken out of the market, then it is essential to know the commercially available materials and their effects. The tests were carried out with a solution simulating the evaporator concentrate waste coming from PWR nuclear reactors. It was cemented using two formulations, A and B, incorporating higher or lower amount of waste, respectively. It was added chemical admixtures from two manufacturers (S and H), which were: accelerators, set retarders and superplasticizers. The experiments were organized by a factorial design 2 3 . The measured parameters were the viscosity, the setting time, the paste and product density and the compressive strength. In this study we performed comparative analyzes of the results of compressive strength at age of 28 and 90 days and between the densities of the samples at the same ages.The compressive strength test at age of 28 days is considered a parameter essential issues related to security handling, transport and storage of cemented waste product. The results showed that the addition of accelerators improved the compressive strength of the cemented product, but presented lower values density products. (author)

Additive Intensity Regression Models in Corporate Default Analysis

DEFF Research Database (Denmark)

Lando, David; Medhat, Mamdouh; Nielsen, Mads Stenbo

2013-01-01

We consider additive intensity (Aalen) models as an alternative to the multiplicative intensity (Cox) models for analyzing the default risk of a sample of rated, nonfinancial U.S. firms. The setting allows for estimating and testing the significance of time-varying effects. We use a variety of mo...

A Pilot Test of the Additive Benefits of Physical Exercise to CBT for OCD.

Science.gov (United States)

Rector, Neil A; Richter, Margaret A; Lerman, Bethany; Regev, Rotem

2015-01-01

The majority of "responders" to first-line cognitive-behavioural therapy (CBT) and pharmacological treatments for obsessive-compulsive disorder (OCD) are left with residual symptoms that are clinically relevant and disabling. Therefore, there is pressing need for widely accessible efficacious alternative and/or adjunctive treatments for OCD. Accumulating evidence suggests that physical exercise may be one such intervention in the mood and anxiety disorders broadly, although we are aware of only two positive small-scale pilot studies that have tested its clinical benefits in OCD. This pilot study aimed to test the feasibility and preliminary efficacy of adding a structured physical exercise programme to CBT for OCD. A standard CBT group was delivered concurrently with a 12-week customized exercise programme to 11 participants. The exercise regimen was individualized for each participant based on peak heart rate measured using an incremental maximal exercise test. Reports of exercise adherence across the 12-week regimen exceeded 80%. A paired-samples t-test indicated very large treatment effects in Yale-Brown Obsessive-Compulsive Scale scores from pre- to post-treatment in CBT group cohorts led by expert CBT OCD specialists (d = 2.55) and junior CBT clinician non-OCD specialists (d = 2.12). These treatment effects are very large and exceed effects typically observed with individual and group-based CBT for OCD based on leading meta-analytic reviews, as well as previously obtained treatment effects for CBT using the same recruitment protocol without exercise. As such, this pilot work demonstrates the feasibility and significant potential clinical utility of a 12-week aerobic exercise programme delivered in conjunction with CBT for OCD.

Can Emergency Medicine Residents Predict Cost of Diagnostic Testing?

Directory of Open Access Journals (Sweden)

Tainter, Christopher R

2017-01-01

Full Text Available Diagnostic testing represents a significant portion of healthcare spending, and cost should be considered when ordering such tests. Needless and excessive spending may occur without an appreciation of the impact on the larger healthcare system. Knowledge regarding the cost of diagnostic testing among emergency medicine (EM residents has not previously been studied. A survey was administered to 20 EM residents from a single ACGME-accredited three-year EM residency program, asking for an estimation of patient charges for 20 commonly ordered laboratory tests and seven radiological exams. We compared responses between residency classes to evaluate whether there was a difference based on level of training. The survey completion rate was 100% (20/20 residents. We noted significant discrepancies between the median resident estimates and actual charge to patient for both laboratory and radiological exams. Nearly all responses were an underestimate of the actual cost. The group median underestimation for laboratory testing was $114, for radiographs $57, and for computed tomography exams was $1,058. There was improvement in accuracy with increasing level of training. This pilot study demonstrates that EM residents have a poor understanding of the charges burdening patients and health insurance providers. In order to make balanced decisions with regard to diagnostic testing, providers must appreciate these factors. Education regarding the cost of providing emergency care is a potential area for improvement of EM residency curricula, and warrants further attention and investigation.

Mismatch Repair Deficiency Testing in Patients With Colorectal Cancer and Nonadherence to Testing Guidelines in Young Adults.

Science.gov (United States)

Shaikh, Talha; Handorf, Elizabeth A; Meyer, Joshua E; Hall, Michael J; Esnaola, Nestor F

2018-02-08

persists. Interventions tailored to groups at risk for nonadherence to guidelines may be warranted in the current era of universal testing.

Testing the Limits: The Purposes and Effects of Additional, External Elementary Mathematics Assessment

Science.gov (United States)

Lombardi, Karen Ann

2011-01-01

This mixed-methods case study focuses on the third through fifth grade classrooms at a public elementary school in a Midwestern urban school district where the Northwest Evaluation Association's (NWEA) Measures of Academic Progress (MAP) assessment is being implemented. According to the school district, the goals of these tests are: to show…

Textile wastewater reuse after additional treatment by Fenton's reagent.

Science.gov (United States)

Ribeiro, Marília Cleto Meirelles; Starling, Maria Clara V M; Leão, Mônica Maria Diniz; de Amorim, Camila Costa

2017-03-01

This study verifies textile wastewater reuse treated by the conventional activated sludge process and subjected to further treatment by advanced oxidation processes. Three alternative processes are discussed: Fenton, photo-Fenton, and UV/H 2 O 2 . Evaluation of treatments effects was based on factorial experiment design in which the response variables were the maximum removal of COD and the minimum concentration of residual H 2 O 2 in treated wastewater. Results indicated Fenton's reagent, COD/[H 2 O 2 ]/[Fe 2+ ] mass ratio of 1:2:2, as the best alternative. The selected technique was applied to real wastewater collected from a conventional treatment plant of a textile mill. The quality of the wastewater before and after the additional treatment was monitored in terms of 16 physicochemical parameters defined as suitable for the characterization of waters subjected to industrial textile use. The degradation of the wastewater was also evaluated by determining the distribution of its molecular weight along with the organic matter fractionation by ultrafiltration, measured in terms of COD. Finally, a sample of the wastewater after additional treatment was tested for reuse at pilot scale in order to evaluate the impact on the quality of dyed fabrics. Results show partial compliance of treated wastewater with the physicochemical quality guidelines for reuse. Removal and conversion of high and medium molecular weight substances into low molecular weight substances was observed, as well as the degradation of most of the organic matter originally present in the wastewater. Reuse tests indicated positive results, confirming the applicability of wastewater reuse after the suggested additional treatment. Graphical abstract Textile wastewater samples after additional treatment by Fenton's reagent, photo-Fenton and H 2 O 2 /UV tested in different conditions.

Additive Manufacturing and Casting Technology Comparison: Mechanical Properties, Productivity and Cost Benchmark

Science.gov (United States)

Vevers, A.; Kromanis, A.; Gerins, E.; Ozolins, J.

2018-04-01

The casting technology is one of the oldest production technologies in the world but in the recent years metal additive manufacturing also known as metal 3D printing has been evolving with huge steps. Both technologies have capabilities to produce parts with internal holes and at first glance surface roughness is similar for both technologies, which means that for precise dimensions parts have to be machined in places where precise fit is necessary. Benchmark tests have been made to find out if parts which are produced with metal additive manufacturing can be used to replace parts which are produced with casting technology. Most of the comparative tests have been made with GJS-400-15 grade which is one of the most popular cast iron grades. To compare mechanical properties samples have been produced using additive manufacturing and tested for tensile strength, hardness, surface roughness and microstructure and then the results have been compared with the samples produced with casting technology. In addition, both technologies have been compared in terms of the production time and production costs to see if additive manufacturing is competitive with the casting technology. The original paper has been written in the Latvian language as part of the Master Thesis within the framework of the production technology study programme at Riga Technical University.

The effect of molybdenum addition on SCC susceptibility of stainless steels in oxygenated high temperature water

International Nuclear Information System (INIS)

Akashi, Masatsune; Kawamoto, Teruaki

1978-01-01

The effect of molybdenum addition on the SCC susceptibility of sensitized stainless steel in oxygenated high temperature water has been studied through the creviced bent beam SCC test (CBB test) and A262E intergranular corrosion test. The molybdenum addition improved the SCC susceptibility of sensitized stainless steels in oxygenated high temperature water not only by delaying the sensitization at lower temperatures but also by increasing the material resistance to the SCC under a given degree of sensitization. These laboratory test results reveal that the molybdenum addition is quite beneficial for improving the SCC susceptibility of stainless steel pipe weld joints in boiling water reactor environment. (auth.)

Laser additive manufacturing bulk graphene-copper nanocomposites.

Science.gov (United States)

Hu, Zengrong; Chen, Feng; Lin, Dong; Nian, Qiong; Parandoush, Pedram; Zhu, Xing; Shao, Zhuqiang; Cheng, Gary J

2017-11-03

The exceptional mechanical properties of graphene make it an ideal nanofiller for reinforcing metal matrix composites (MMCs). In this work, graphene-copper (Gr-Cu) nanocomposites have been fabricated by a laser additive manufacturing process. Transmission electron microscopy (TEM), x-ray diffraction (XRD) and Raman spectroscopy were utilized to characterize the fabricated nanocomposites. The XRD, Raman spectroscopy, energy dispersive spectroscopy and TEM results demonstrated the feasibility of laser additive manufacturing of Gr-Cu nanocomposites. The microstructures were characterized by high resolution TEM and the results further revealed the interface between the copper matrix and graphene. With the addition of graphene, the mechanical properties of the composites were enhanced significantly. Nanoindentation tests showed that the average modulus value and hardness of the composites were 118.9 GPa and 3 GPa respectively; 17.6% and 50% increases were achieved compared with pure copper, respectively. This work demonstrates a new way to manufacture graphene copper nanocomposites with ultra-strong mechanical properties and provides alternatives for applications in electrical and thermal conductors.

Genetics educational needs in China: physicians' experience and knowledge of genetic testing.

Science.gov (United States)

Li, Jing; Xu, Tengda; Yashar, Beverly M

2015-09-01

The aims of this study were to explore the relationship between physicians' knowledge and utilization of genetic testing and to explore genetics educational needs in China. An anonymous survey about experience, attitudes, and knowledge of genetic testing was conducted among physicians affiliated with Peking Union Medical College Hospital during their annual health evaluation. A personal genetics knowledge score was developed and predictors of personal genetics knowledge score were evaluated. Sixty-four physicians (33% male) completed the survey. Fifty-eight percent of them had used genetic testing in their clinical practice. Using a 4-point scale, mean knowledge scores of six common genetic testing techniques ranged from 1.7 ± 0.9 to 2.4 ± 1.0, and the average personal genetics knowledge score was 2.1 ± 0.8. In regression analysis, significant predictors of higher personal genetics knowledge score were ordering of genetic testing, utilization of pedigrees, higher medical degree, and recent genetics training (P education. This study demonstrated a sizable gap between Chinese physicians' knowledge and utilization of genetic testing. Participants had high self-perceived genetics educational needs. Development of genetics educational platforms is both warranted and desired in China.Genet Med 17 9, 757-760.

Effects of additives on thermal stability of Li ion cells

Science.gov (United States)

Doughty, Daniel H.; Roth, E. Peter; Crafts, Chris C.; Nagasubramanian, G.; Henriksen, Gary; Amine, Khalil

Li ion cells are being developed for high-power applications in hybrid electric vehicles, because these cells offer superior combination of power and energy density over current cell chemistries. Cells using this chemistry are proposed for battery systems in both internal combustion engine and fuel cell-powered hybrid electric vehicles. However, the safety of these cells needs to be understood and improved for eventual widespread commercial applications. The thermal-abuse response of Li ion cells has been improved by the incorporation of more stable anode carbons and electrolyte additives. Electrolyte solutions containing vinyl ethylene carbonate (VEC), triphenyl phosphate (TPP), tris(trifluoroethyl)phosphate (TFP) as well as some proprietary flame-retardant additives were evaluated. Test cells in the 18,650 configuration were built at Sandia National Laboratories using new stable electrode materials and electrolyte additives. A special test fixture was designed to allow determination of self-generated cell heating during a thermal ramp profile. The flammability of vented gas and expelled electrolyte was studied using a novel arrangement of a spark generator placed near the cell to ignite vent gas if a flammable gas mixture was present. Flammability of vent gas was somewhat reduced by the presence of certain additives. Accelerating rate calorimetry (ARC) was also used to characterize 18,650-size test cell heat and gas generation. Gas composition was analyzed by gas chromatography (GC) and was found to consist of CO 2, H 2, CO, methane, ethane, ethylene and small amounts of C1-C4 organic molecules.

Additive and Multiplicative Effects of Working Memory and Test Anxiety on Mathematics Performance in Grade 3 Students

Science.gov (United States)

Korhonen, Johan; Nyroos, Mikaela; Jonsson, Bert; Eklöf, Hanna

2018-01-01

The aim of this study was to investigate the interplay between test anxiety and working memory (WM) on mathematics performance in younger children. A sample of 624 grade 3 students completed a test battery consisting of a test anxiety scale, WM tasks and the Swedish national examination in mathematics for grade 3. The main effects of test anxiety…

BFR Electrolyte Additive Safety and Flammability Characterization

Energy Technology Data Exchange (ETDEWEB)

Allcorn, Eric [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

2017-10-13

Lithium-ion battery safety is a critical issue in the adoption of the chemistry to larger scale applications such as transportation and stationary storage. One of the critical components impacting the safety of lithium-ion batteries is their use of highly flammable organic electrolytes. In this work, brominated flame retardants (BFR’s) – an existing class of flame retardant materials – are incorporated as additives to lithium-ion battery electrolytes with the intention to reduce the electrolyte flammability and thereby improve safety. There are a few critical needs for a successful electrolyte additive: solubility in the electrolyte, electrochemical stability over the range of battery operation, and minimal detrimental effects on battery performance. Those detrimental effects can take the form of electrolyte specific impacts, such as a reduction in conductivity, or electrode impacts, such as SEI-layer modification or chemical instability to the active material. In addition to these needs, the electrolyte additive also needs to achieve its intended purpose, which in this case is to reduce the flammability of the electrolyte. For the work conducted as part of this SPP agreement three separate BFR materials were provided by Albemarle to be tested by Sandia as additives in a traditional lithium-ion battery electrolyte. The provided BFR materials were tribromo-neopentyl alcohol, tetrabromo bisphenol A, and tribromoethylene. These materials were incorporated as separate 4 wt.% additives into a traditional lithium-ion battery electrolyte and compared to said traditional electrolyte, designated Gen2.

Field and laboratory determination of a poly(vinyl/vinylidene chloride) additive in brick mortar.

Science.gov (United States)

Law, S L; Newman, J H; Ptak, F L

1990-02-01

A polymerized vinyl/vinylidene chloride additive, used in brick mortar during the 60s and 70s, is detected at the building site by the field method, which employs a commercially available chloride test strip. The field test results can then be verified by the laboratory methods. In one method, total chlorine in the mortar is determined by an oxygen-bomb method and the additive chloride is determined by difference after water-soluble chlorides have been determined on a separate sample. In the second method, the polymerized additive is extracted directly from the mortar with tetrahydrofuran (THF). The difference in weight before and after extraction of the additive gives the weight of additive in the mortar. Evaporation of the THF from the extract leaves a thin film of the polymer, which gives an infrared "fingerprint" spectrum characteristic of the additive polymer.

Microbial analyses of cement and grouting additives

International Nuclear Information System (INIS)

Hallbeck, L.; Jaegevall, S.; Paeaejaervi, A.; Rabe, L.; Edlund, J.; Eriksson, S.

2012-01-01

During sampling in the ONKALO tunnel in 2006, heavy growth of a slimy material was observed in connection with grouting. It was suggested to be microbial growth on organic additives leaching from the grout. Two sampling campaigns resulted in the isolation of several aerobic bacterial strains. Some of these strains were used in biodegradation studies of three solid cement powders, eight liquid grout additives, and six plastic drainage materials. Degradation was also studied using ONKALO groundwaters as inoculums. The isolated strains were most closely related to hydrocarbon-degrading microorganisms. The biodegradation of seven of the products was tested using microorganisms isolated from the ONKALO slime in 2006; none of these strains could degrade the tested products. When ONKALO drillhole groundwaters were used as inoculums in the degradation studies, it was demonstrated that Structuro 111X, Mighty 150, and Super-Parmix supported growth of the groundwater microorganisms. Structuro 111X is a polycarboxylate condensate while Mighty 150 and Super-Parmix are condensates with formaldehyde and naphthalene. Some of the isolated microorganisms belonged to the genus Pseudomonas, many strains of which can degrade organic molecules. None of the plastic drainage materials supported growth during the degradation studies. Microorganisms were present in two of the liquid products when delivered, GroutAid and Super-Parmix. The potential of the organic compounds in grout additives to be degraded by microorganisms, increasing the risk of biofilm formation and complexing compound production, must be considered. Microbial growth will also increase the possibility of hydrogen sulphide formation. (orig.)

Validating a dance-specific screening test for balance: preliminary results from multisite testing.

Science.gov (United States)

Batson, Glenna

2010-09-01

Few dance-specific screening tools adequately capture balance. The aim of this study was to administer and modify the Star Excursion Balance Test (oSEBT) to examine its utility as a balance screen for dancers. The oSEBT involves standing on one leg while lightly targeting with the opposite foot to the farthest distance along eight spokes of a star-shaped grid. This task simulates dance in the spatial pattern and movement quality of the gesturing limb. The oSEBT was validated for distance on athletes with history of ankle sprain. Thirty-three dancers (age 20.1 +/- 1.4 yrs) participated from two contemporary dance conservatories (UK and US), with or without a history of lower extremity injury. Dancers were verbally instructed (without physical demonstration) to execute the oSEBT and four modifications (mSEBT): timed (speed), timed with cognitive interference (answering questions aloud), and sensory disadvantaging (foam mat). Stepping strategies were tracked and performance strategies video-recorded. Unlike the oSEBT results, distances reached were not significant statistically (p = 0.05) or descriptively (i.e., shorter) for either group. Performance styles varied widely, despite sample homogeneity and instructions to control for strategy. Descriptive analysis of mSEBT showed an increased number of near-falls and decreased timing on the injured limb. Dancers appeared to employ variable strategies to keep balance during this test. Quantitative analysis is warranted to define balance strategies for further validation of SEBT modifications to determine its utility as a balance screening tool.

Ductility and fracture of single crystaliine Ni3Al with boron additions

International Nuclear Information System (INIS)

Heredia, F.E.; Pope, D.P.

1989-01-01

Low and high temperature tensile tests were performed on single crystals of pure Ni 3 Al and Ni 3 Al+B in order to determine the effect of B additions on the ductility and fracture behavior. Tests were carried out in air at a constant strain rate of 1/3 x 10 -3 s -1 . The orientation tested were [001] for whic the yield stress in tension is always greater than in compression, and those for wich the tension/compression asymmetry is zero ([T=C]) for each particular composition. At room temperature, the results show a positive effect of B additions on both the fracture stress and on the ductility. The ductility at 800K appears to decrease monotonically with B additions. The largest ductilities are found for [T=C] at room temperature where an improvement of about 26% (resolved strain) for an addition of 0.2 at % B was obtained. However, the most dramatic increase in ductility occurs for the [001] oriented samples at room temperature where a 55% improvement was measured over that of pure Ni 3 Al. Fracture surfaces show a combinaton of massive slip, some clevage, and heavily dimpled areas. These observations show that B additions not only increase the ductility of polycrystalline Ni 3 Al, as has been previously observed by many investigators, but also that the already-ductile single crystalline material, indicating that a bulk effect should be added to the grain boundary strengthening effect of B when explaining the improvement in ductility of polycrystalline Ni 3 Al due to B additions

Changes of Properties of Bitumen Binders by Additives Application

Science.gov (United States)

Remišová, Eva; Holý, Michal

2017-10-01

Requirements for properties of bituminous binders are determined in the European standards. The physico-chemical behaviour of bitumen depends on its colloidal structure (asphaltenes dispersed into an oily matrix constituted by saturates, aromatics and resins) that depends primarily on its crude source and processing. Bitumen properties are evaluated by group composition, elementary analysis, but more often conventional or functional tests. Bitumen for road uses is assessed according to the physical characteristics. For the purpose of improving the qualitative properties of bitumen and asphalts the additives are applied e.g. to increase elasticity, improving the heat stability, improving adhesion to aggregate, to decrease viscosity, increasing the resistance to aging, to prevent binder drainage from the aggregate surface, etc. The objective of presented paper is to assess and compare effect of additives on properties of bitumen binders. In paper, the results of bitumen properties, penetration, softening point, and dynamic viscosity of two paving grade bitumen 35/50, 50/70 and polymer modified bitumen PmB 45/80-75 are analyzed and also the changes of these properties by the application of selected additives (Sasobit, Licomont BS100, Wetfix BE and CWM) to improve adhesion to aggregate and improve workability. Measurements of properties have been performed according to the relevant European standards. The laboratory tests showed significantly increasing the softening point of paving grade bitumen 50/70 and 35/50 by 13 to 45°C. The effect of various additives on bitumen softening point is different. Penetration varies according to type of bitumen and type of used additive. The penetration values of modified bitumen PmB 45/80-75 with additives Sasobit and Licomont BS100 show increase of bitumen stiffness of 16 0.1mm and a shift in the gradation. The changes in penetration and in softening point significantly shown when calculating on Penetration index as a parameter of

Machinability of structural steels with calcium addition

International Nuclear Information System (INIS)

Pytel, S.; Zadecki, M.

2003-01-01

The machinability of the plain carbon and low alloy structural steels with carbon content of 0.1-0.6% is briefly discussed in the first part of the paper. In the experimental part a dependence between the addition of calcium and some changes in sulphide and oxide inclusions morphology is presented. The Volvo test for measurement of machinability index B i has been applied. Using the multiple regression methods two relationships between machinability index B i and stereological parameters of non-metallic inclusions as well as hardness of the steels have been calculated. The authors have reached the conclusion that owing to the changes in inclusion chemical composition and geometry as result of calcium addition the machinability index of the steel can be higher. (author)

Risk of breast cancer after a diagnosis of ovarian cancer in BRCA mutation carriers: Is preventive mastectomy warranted?

Science.gov (United States)

McGee, Jacob; Giannakeas, Vasily; Karlan, Beth; Lubinski, Jan; Gronwald, Jacek; Rosen, Barry; McLaughlin, John; Risch, Harvey; Sun, Ping; Foulkes, William D; Neuhausen, Susan L; Kotsopoulos, Joanne; Narod, Steven A

2017-05-01

Preventive breast surgery and MRI screening are offered to unaffected BRCA mutation carriers. The clinical benefit of these two modalities has not been evaluated among mutation carriers with a history of ovarian cancer. Thus, we sought to determine whether or not BRCA mutation carriers with ovarian cancer would benefit from preventive mastectomy or from MRI screening. First, the annual mortality rate for ovarian cancer patients was estimated for a cohort of 178 BRCA mutation carriers from Ontario, Canada. Next, the actuarial risk of developing breast cancer was estimated using an international registry of 509 BRCA mutation carriers with ovarian cancer. A series of simulations was conducted to evaluate the reduction in the probability of death (from all causes) associated with mastectomy and with MRI-based breast surveillance. Cox proportional hazards models were used to evaluate the impacts of mastectomy and MRI screening on breast cancer incidence as well as on all-cause mortality. Twenty (3.9%) of the 509 patients developed breast cancer within ten years following ovarian cancer diagnosis. The actuarial risk of developing breast cancer at ten years post-diagnosis, conditional on survival from ovarian cancer and other causes of mortality was 7.8%. Based on our simulation results, among all BRCA mutation-carrying patients diagnosed with stage III/IV ovarian cancer at age 50, the chance of dying before age 80 was reduced by less than 1% with MRI and by less than 2% with mastectomy. Greater improvements in survival with MRI or mastectomy were observed for women who had already survived 10years after ovarian cancer, and for women with stage I or II ovarian cancer. Among BRCA mutation-carrying ovarian cancer patients without a personal history of breast cancer, neither preventive mastectomy nor MRI screening is warranted, except for those who have survived ovarian cancer without recurrence for ten years and for those with early stage ovarian cancer. Copyright © 2017

Neutron measurements of stresses in a test artifact produced by laser-based additive manufacturing

Energy Technology Data Exchange (ETDEWEB)

Gnäupel-Herold, Thomas [Center for Neutron Research, National Institute of Standards and Technology, Gaithersburg MD 20899-6102 (United States); Slotwinski, John; Moylan, Shawn [Intelligent Systems Division, National Institute of Standards and Technology, Gaithersburg MD 20899-8220 (United States)

2014-02-18

A stainless steel test artifact produced by Direct Metal Laser Sintering and similar to a proposed standardized test artifact was examined using neutron diffraction. The artifact contained a number of structures with different aspect ratios pertaining to wall thickness, height above base plate, and side length. Through spatial resolutions of the order of one millimeter the volumetric distribution of stresses in several was measured. It was found that the stresses peak in the tensile region around 500 MPa near the top surface, with balancing compressive stresses in the interior. The presence of a support structure (a one millimeter high, thin walled, hence weaker, lattice structure deposited on the base plate, followed by a fully dense AM structure) has only minor effects on the stresses.

Shear bond strength of self-etch adhesives to enamel with additional phosphoric acid etching.

Science.gov (United States)

Lührs, Anne-Katrin; Guhr, Silke; Schilke, Reinhard; Borchers, Lothar; Geurtsen, Werner; Günay, Hüsamettin

2008-01-01

This study evaluated the shear bond strength of self-etch adhesives to enamel and the effect of additional phosphoric acid etching. Seventy sound human molars were randomly divided into three test groups and one control group. The enamel surfaces of the control group (n=10) were treated with Syntac Classic (SC). Each test group was subdivided into two groups (each n=10). In half of each test group, ground enamel surfaces were coated with the self-etch adhesives AdheSe (ADH), Xeno III (XE) or Futurabond NR (FNR). In the remaining half of each test group, an additional phosphoric acid etching of the enamel surface was performed prior to applying the adhesives. The shear bond strength was measured with a universal testing machine at a crosshead speed of 1 mm/minute after storing the samples in distilled water at 37 degrees C for 24 hours. Fracture modes were determined by SEM examination. For statistical analysis, one-way ANOVA and the two-sided Dunnett Test were used (p>0.05). Additional phosphoric etching significantly increased the shear bond strength of all the examined self-etch adhesives (padhesive fractures. For all the self-etch adhesives, a slight increase in mixed fractures occurred after conditioning with phosphoric acid. An additional phosphoric acid etching of enamel should be considered when using self-etch adhesives. More clinical studies are needed to evaluate the long-term success of the examined adhesives.

Large fluctuations of the macroscopic current in diffusive systems: a numerical test of the additivity principle.

Science.gov (United States)

Hurtado, Pablo I; Garrido, Pedro L

2010-04-01

Most systems, when pushed out of equilibrium, respond by building up currents of locally conserved observables. Understanding how microscopic dynamics determines the averages and fluctuations of these currents is one of the main open problems in nonequilibrium statistical physics. The additivity principle is a theoretical proposal that allows to compute the current distribution in many one-dimensional nonequilibrium systems. Using simulations, we validate this conjecture in a simple and general model of energy transport, both in the presence of a temperature gradient and in canonical equilibrium. In particular, we show that the current distribution displays a Gaussian regime for small current fluctuations, as prescribed by the central limit theorem, and non-Gaussian (exponential) tails for large current deviations, obeying in all cases the Gallavotti-Cohen fluctuation theorem. In order to facilitate a given current fluctuation, the system adopts a well-defined temperature profile different from that of the steady state and in accordance with the additivity hypothesis predictions. System statistics during a large current fluctuation is independent of the sign of the current, which implies that the optimal profile (as well as higher-order profiles and spatial correlations) are invariant upon current inversion. We also demonstrate that finite-time joint fluctuations of the current and the profile are well described by the additivity functional. These results suggest the additivity hypothesis as a general and powerful tool to compute current distributions in many nonequilibrium systems.

Additive Manufacturing of Porous Metal

Energy Technology Data Exchange (ETDEWEB)

Dehoff, Ryan R. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Kirka, Michael M. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

2017-06-01

Currently, helium is obtained through separation from natural gas. The current industrial process incurs significant costs and requires large energy resources to successfully achieve separation. Through utilizing Additive Manufacturing (AM) technologies it is possible to reduce both of these burdens when refining helium gas. The ability to engineer porosity levels within Inconel 718 discs for controlled separation of helium from natural gas was investigated. Arrays of samples fabricated using the electron beam melting process were analyzed for their relative porosity density. Based upon the measurements, full scale discs were fabricated, and subsequently tested to determine their effectiveness in separating helium from liquefied natural gas.

Durability of European Asphalt Mixtures Containing Reclaimed Asphalt and Warm-Mix Additives

NARCIS (Netherlands)

Varveri, A.; Avgerinopoulos, S.; Scarpas, Athanasios

2016-01-01

This paper investigates the moisture susceptibility of European asphalt mixtures (SMA) containing reclaimed asphalt (RA) and warm mix (WMA) additives. Test sections of a typical SMA mixture have been laid, from which cylindrical samples were cored and utilized for laboratory testing. Four variants

Metal Additive Manufacturing: A Review of Mechanical Properties

Science.gov (United States)

Lewandowski, John J.; Seifi, Mohsen

2016-07-01

This article reviews published data on the mechanical properties of additively manufactured metallic materials. The additive manufacturing techniques utilized to generate samples covered in this review include powder bed fusion (e.g., EBM, SLM, DMLS) and directed energy deposition (e.g., LENS, EBF3). Although only a limited number of metallic alloy systems are currently available for additive manufacturing (e.g., Ti-6Al-4V, TiAl, stainless steel, Inconel 625/718, and Al-Si-10Mg), the bulk of the published mechanical properties information has been generated on Ti-6Al-4V. However, summary tables for published mechanical properties and/or key figures are included for each of the alloys listed above, grouped by the additive technique used to generate the data. Published values for mechanical properties obtained from hardness, tension/compression, fracture toughness, fatigue crack growth, and high cycle fatigue are included for as-built, heat-treated, and/or HIP conditions, when available. The effects of test orientation/build direction on properties, when available, are also provided, along with discussion of the potential source(s) (e.g., texture, microstructure changes, defects) of anisotropy in properties. Recommendations for additional work are also provided.

Additive Manufacturing of Low Cost Upper Stage Propulsion Components

Science.gov (United States)

Protz, Christopher; Bowman, Randy; Cooper, Ken; Fikes, John; Taminger, Karen; Wright, Belinda

2014-01-01

NASA is currently developing Additive Manufacturing (AM) technologies and design tools aimed at reducing the costs and manufacturing time of regeneratively cooled rocket engine components. These Low Cost Upper Stage Propulsion (LCUSP) tasks are funded through NASA's Game Changing Development Program in the Space Technology Mission Directorate. The LCUSP project will develop a copper alloy additive manufacturing design process and develop and optimize the Electron Beam Freeform Fabrication (EBF3) manufacturing process to direct deposit a nickel alloy structural jacket and manifolds onto an SLM manufactured GRCop chamber and Ni-alloy nozzle. In order to develop these processes, the project will characterize both the microstructural and mechanical properties of the SLMproduced GRCop-84, and will explore and document novel design techniques specific to AM combustion devices components. These manufacturing technologies will be used to build a 25K-class regenerative chamber and nozzle (to be used with tested DMLS injectors) that will be tested individually and as a system in hot fire tests to demonstrate the applicability of the technologies. These tasks are expected to bring costs and manufacturing time down as spacecraft propulsion systems typically comprise more than 70% of the total vehicle cost and account for a significant portion of the development schedule. Additionally, high pressure/high temperature combustion chambers and nozzles must be regeneratively cooled to survive their operating environment, causing their design to be time consuming and costly to build. LCUSP presents an opportunity to develop and demonstrate a process that can infuse these technologies into industry, build competition, and drive down costs of future engines.

Influence of metallic based fuel additives on performance and exhaust emissions of diesel engine

Energy Technology Data Exchange (ETDEWEB)

Keskin, Ali [Tarsus Technical Education Faculty, Mersin University, 33500 Mersin (Turkey); Guerue, Metin, E-mail: mguru@gazi.edu.t [Engineering and Architectural Faculty, Gazi University, 06570 Maltepe, Ankara (Turkey); Altiparmak, Duran [Technical Education Faculty, Gazi University, 06500 Ankara (Turkey)

2011-01-15

In this experimental study, influence of the metallic-based additives on fuel consumption and exhaust emissions of diesel engine were investigated. The metallic-based additives were produced by synthesizing of resin acid (abietic acid) with MnO{sub 2} or MgO. These additives were doped into diesel fuel at the rate of 8 {mu}mol/l and 16 {mu}mol/l for preparing test fuels. Both additives improved the properties of diesel fuel such as viscosity, flash point, cloud point and pour point. The fuels with and without additives were tested in a direct injection diesel engine at full load condition. Maximum reduction of specific fuel consumption was recorded as 4.16%. CO emission and smoke opacity decreased by 16.35% and by 29.82%, respectively. NO{sub x} emission was measured higher and CO{sub 2} emission was not changed considerably with the metallic-based additives.

46 CFR 160.035-12 - Additional preapproval tests required for F.R.P. lifeboats.

Science.gov (United States)

2010-10-01

... that when hanging freely the gunwale on one side of the boat is approximately 2 inches from a... no damage which would render the boat unserviceable. (4) Drop test. The boat shall be loaded with...

Additive Manufacturing of Ultem Polymers and Composites

Science.gov (United States)

Chuang, Kathy C.; Grady, Joseph E.; Draper, Robert D.; Shin, Euy-Sik E.; Patterson, Clark; Santelle, Thomas D.

2015-01-01

The objective of this project was to conduct additive manufacturing to produce aircraft engine components by Fused Deposition Modeling (FDM), using commercially available polyetherimdes Ultem 9085 and experimental Ultem 1000 filled with 10 chopped carbon fiber. A property comparison between FDM-printed and injection molded coupons for Ultem 9085, Ultem 1000 resin and the fiber-filled composite Ultem 1000 was carried out. Furthermore, an acoustic liner was printed from Ultem 9085 simulating conventional honeycomb structured liners and tested in a wind tunnel. Composite compressor inlet guide vanes were also printed using fiber-filled Ultem 1000 filaments and tested in a cascade rig. The fiber-filled Ultem 1000 filaments and composite vanes were characterized by scanning electron microscope (SEM) and acid digestion to determine the porosity of FDM-printed articles which ranged from 25-31. Coupons of Ultem 9085, experimental Ultem 1000 composites and XH6050 resin were tested at room temperature and 400F to evaluate their corresponding mechanical properties.

Solar Alpha Rotary Joint (SARJ) Lubrication Interval Test and Evaluation (LITE). Post-Test Grease Analysis

Science.gov (United States)

Golden, Johnny L.; Martinez, James E.; Devivar, Rodrigo V.

2015-01-01

The Solar Alpha Rotary Joint (SARJ) is a mechanism of the International Space Station (ISS) that orients the solar power generating arrays toward the sun as the ISS orbits our planet. The orientation with the sun must be maintained to fully charge the ISS batteries and maintain all the other ISS electrical systems operating properly. In 2007, just a few months after full deployment, the starboard SARJ developed anomalies that warranted a full investigation including ISS Extravehicular Activity (EVA). The EVA uncovered unexpected debris that was due to degradation of a nitride layer on the SARJ bearing race. ISS personnel identified the failure root-cause and applied an aerospace grease to lubricate the area associated with the anomaly. The corrective action allowed the starboard SARJ to continue operating within the specified engineering parameters. The SARJ LITE (Lubrication Interval Test and Evaluation) program was initiated by NASA, Lockheed Martin, and Boeing to simulate the operation of the ISS SARJ for an extended time. The hardware was designed to test and evaluate the exact material components used aboard the ISS SARJ, but in a controlled area where engineers could continuously monitor the performance. After running the SARJ LITE test for an equivalent of 36+ years of continuous use, the test was opened to evaluate the metallography and lubrication. We have sampled the SARJ LITE rollers and plate to fully assess the grease used for lubrication. Chemical and thermal analysis of these samples has generated information that has allowed us to assess the location, migration, and current condition of the grease. The collective information will be key toward understanding and circumventing any performance deviations involving the ISS SARJ in the years to come.

Pre- and Post-Transfusion Alloimmunization in Dogs Characterized by 2 Antiglobulin-Enhanced Cross-match Tests.

Science.gov (United States)

Goy-Thollot, I; Giger, U; Boisvineau, C; Perrin, R; Guidetti, M; Chaprier, B; Barthélemy, A; Pouzot-Nevoret, C; Canard, B

2017-09-01

When dogs are transfused, blood compatibility testing varies widely but may include dog erythrocyte antigen (DEA) 1 typing and rarely cross-matching. Prospective study to examine naturally occurring alloantibodies against red blood cells (RBCs) and alloimmunization by transfusion using 2 antiglobulin-enhanced cross-match tests. Eighty client-owned anemic, 72 donor, and 7 control dogs. All dogs were typed for DEA 1 and some also for DEA 4 and DEA 7. Major cross-match tests with canine antiglobulin-enhanced immunochromatographic strip and gel columns were performed 26-129 days post-transfusion (median, 39 days); some dogs had an additional early evaluation 11-22 days post-transfusion (median, 16 days). Plasma from alloimmunized recipients was cross-matched against RBCs from 34 donor and control dogs. The 2 cross-match methods gave entirely concordant results. All 126 pretransfusion cross-match results for the 80 anemic recipients were compatible, but 54 dogs died or were lost to follow up. Among the 26 recipients with follow-up, 1 dog accidently received DEA 1-mismatched blood and became cross-match-incompatible post-transfusion. Eleven of the 25 DEA 1-matched recipients (44%) became incompatible against other RBC antigens. No naturally occurring anti-DEA 7 alloantibodies were detected in DEA 7- dogs. The antiglobulin-enhanced immunochromatographic strip cross-match and laboratory gel column techniques identified no naturally occurring alloantibodies against RBC antigens, but a high degree of post-transfusion alloimmunization in dogs. Cross-matching is warranted in any dog that has been previously transfused independent of initial DEA 1 typing and cross-matching results before the first transfusion event. Copyright © 2017 The Authors. Journal of Veterinary Internal Medicine published by Wiley Periodicals, Inc. on behalf of the American College of Veterinary Internal Medicine.

Application of Natural Mineral Additives in Construction

Science.gov (United States)

Linek, Malgorzata; Nita, Piotr; Wolka, Paweł; Zebrowski, Wojciech

2017-12-01

The article concerns the idea of using selected mineral additives in the pavement quality concrete composition. The basis of the research paper was the modification of cement concrete intended for airfield pavements. The application of the additives: metakaolonite and natural zeolite was suggested. Analyses included the assessment of basic physical properties of modifiers. Screening analysis, assessment of micro structure and chemical microanalysis were conducted in case of these materials. The influence of the applied additives on the change of concrete mix parameters was also presented. The impact of zeolite and metakaolinite on the mix density, oxygen content and consistency class was analysed. The influence of modifiers on physical and mechanical changes of the hardened cement concrete was discussed (concrete density, compressive strength and bending strength during fracturing) in diversified research periods. The impact of the applied additives on the changes of internal structure of cement concrete was discussed. Observation of concrete micro structure was conducted using the scanning electron microscope. According to the obtained lab test results, parameters of the applied modifiers and their influence on changes of internal structure of cement concrete are reflected in the increase of mechanical properties of pavement quality concrete. The increase of compressive and bending strength in case of all analysed research periods was proved.

PCR-based verification of positive rapid diagnostic tests for intestinal protozoa infections with variable test band intensity.

Science.gov (United States)

Becker, Sören L; Müller, Ivan; Mertens, Pascal; Herrmann, Mathias; Zondie, Leyli; Beyleveld, Lindsey; Gerber, Markus; du Randt, Rosa; Pühse, Uwe; Walter, Cheryl; Utzinger, Jürg

2017-10-01

Stool-based rapid diagnostic tests (RDTs) for pathogenic intestinal protozoa (e.g. Cryptosporidium spp. and Giardia intestinalis) allow for prompt diagnosis and treatment in resource-constrained settings. Such RDTs can improve individual patient management and facilitate population-based screening programmes in areas without microbiological laboratories for confirmatory testing. However, RDTs are difficult to interpret in case of 'trace' results with faint test band intensities and little is known about whether such ambiguous results might indicate 'true' infections. In a longitudinal study conducted in poor neighbourhoods of Port Elizabeth, South Africa, a total of 1428 stool samples from two cohorts of schoolchildren were examined on the spot for Cryptosporidium spp. and G. intestinalis using an RDT (Crypto/Giardia DuoStrip; Coris BioConcept). Overall, 121 samples were positive for G. intestinalis and the RDT suggested presence of cryptosporidiosis in 22 samples. After a storage period of 9-10 months in cohort 1 and 2-3 months in cohort 2, samples were subjected to multiplex PCR (BD Max™ Enteric Parasite Panel, Becton Dickinson). Ninety-three percent (112/121) of RDT-positive samples for G. intestinalis were confirmed by PCR, with a correlation between RDT test band intensity and quantitative pathogen load present in the sample. For Cryptosporidium spp., all positive RDTs had faintly visible lines and these were negative on PCR. The performance of the BD Max™ PCR was nearly identical in both cohorts, despite the prolonged storage at disrupted cold chain conditions in cohort 1. The Crypto/Giardia DuoStrip warrants further validation in communities with a high incidence of diarrhoea. Copyright © 2017 Elsevier B.V. All rights reserved.

ADME-Tox profiles of some food additives and pesticides

Science.gov (United States)

Craciun, Dana; Modra, Dorina; Isvoran, Adriana

2015-12-01

Within this study we compute the Absorption, Distribution, Metabolism, Excretion and Toxicity (ADME-Tox) profiles of several commonly used food additives and some pesticides. As expected, all the food additives considered in this study provided to be safe, their ADME-Tox profiles indicating that they have a good oral bioavailability and they do not produce phosphoslipidosis. The ADME-Tox profiles of the pesticides indicate that, with a few exceptions, they are highly toxic (some of them being not approved in the EU, but still used in other countries) and may cause many diseases. Our results are in good agreement with published data concerning the considered food additives and pesticides revealing that the ADME-Tox profiling method may be successfully used to test other chemicals than drug candidates.

Utilization of curve offsets in additive manufacturing

Science.gov (United States)

Haseltalab, Vahid; Yaman, Ulas; Dolen, Melik

2018-05-01

Curve offsets are utilized in different fields of engineering and science. Additive manufacturing, which lately becomes an explicit requirement in manufacturing industry, utilizes curve offsets widely. One of the necessities of offsetting is for scaling which is required if there is shrinkage after the fabrication or if the surface quality of the resulting part is unacceptable. Therefore, some post-processing is indispensable. But the major application of curve offsets in additive manufacturing processes is for generating head trajectories. In a point-wise AM process, a correct tool-path in each layer can reduce lots of costs and increase the surface quality of the fabricated parts. In this study, different curve offset generation algorithms are analyzed to show their capabilities and disadvantages through some test cases and improvements on their drawbacks are suggested.

Platelet crossmatch tests using radiolabelled staphylococcal protein A or peroxidase anti-peroxidase in alloimmunised patients

International Nuclear Information System (INIS)

Yam, P.; Petz, L.D.; Scott, E.P.; Santos, S.

1984-01-01

Refractoriness to random-donor platelets as a result of alloimmunization remains a major problem in long-term platelet transfusion therapy despite the use of HLA-matched platelets. A study has been made of two methods for detection of platelet associated IgG as platelet crossmatch tests for the selection of platelet donors. These methods use radiolabelled staphylococcal protein A( 125 I-SPA) and peroxidase anti-peroxidase (PAP), respectively. One hundred and ten crossmatch tests using 125 I-SPA were performed retrospectively in 18 alloimmunized patients. The results indicated that the predictive value of a positive or a negative test was 87%; the sensitivity was 73% and the specificity was 95%. Results with the PAP test were similar. The HLA types were known for 48 donor-recipient pairs. With few exceptions, there was a correlation between the results of the platelet crossmatch tests and the effectiveness of platelet transfusion regardless of the degree of HLA match. These results indicate that platelet crossmatch tests may be valuable even when closely HLA matched donors are not available. A large-scale prospective study is warranted, particularly in highly immunized patients. (author)

Understanding Referral Patterns for Bone Mineral Density Testing among Family Physicians: A Qualitative Descriptive Study

Directory of Open Access Journals (Sweden)

Sarah E. P. Munce

2016-01-01

Full Text Available Introduction. Evidence of inappropriate bone mineral density (BMD testing has been identified in terms of overtesting in low risk women and undertesting among patients at high risk. In light of these phenomena, the objective of this study was to understand the referral patterns for BMD testing among Ontario’s family physicians (FPs. Methods. A qualitative descriptive approach was adopted. Twenty-two FPs took part in a semi-structured interview lasting approximately 30 minutes. An inductive thematic analysis was performed on the transcribed data in order to understand the referral patterns for BMD testing. Results. We identified a lack of clarity about screening for osteoporosis with a tendency for baseline BMD testing in healthy, postmenopausal women and a lack of clarity on the appropriate age for screening for men in particular. A lack of clarity on appropriate intervals for follow-up testing was also described. Conclusions. These findings lend support to what has been documented at the population level suggesting a tendency among FPs to refer menopausal women (at low risk. Emphasis on referral of high-risk groups as well as men and further clarification and education on the appropriate intervals for follow-up testing is warranted.

Modified Longo's stapled hemorrhoidopexy with additional traction sutures for the treatment of residual prolapsed piles.

Science.gov (United States)

Chen, Chuang-Wei; Kang, Jung-Cheng; Wu, Chang-Chieh; Hsiao, Cheng-Wen; Jao, Shu-Wen

2008-03-01

Residual prolapsed piles is a problem after the stapled hemorrhoidopexy, especially in large third- or fourth-degree hemorrhoids. We have developed a method using additional traction sutures along with modified Longo's procedure to manage this problem. From January 2005 to October 2005, 30 consecutive patients with symptomatic third- or fourth-degree hemorrhoids who underwent the modified Longo's stapled hemorrhoidopexy with additional traction sutures in a single institution were collected. The demographics, postoperative pain score, surgical features, outcomes, and early and late complications were recorded. All patients were followed for a mean duration of 8.8 (range, 4-15) months. Thirty patients (17 males) with a mean age of 45 (range, 27-63) years were identified. The mean postoperative pain score on the morning of the first postoperative day was 2.8 (range, 1-4). The mean duration of operation was 30.7 (range, 25-37) min. The mean duration of hospital stay was 2 (range, 1-3) days. The mean days for patients to resume normal work was 6.7 (range, 4-9) days. No other procedure-related complications occurred in all patients. There was no early complication except for fecal urgency found in one patient during the first postoperative days. Regarding the late complications, no residual prolapsed piles, persistent anal pain, incontinence, anal stenosis, or recurrent symptoms were found. Our preliminary experiences indicated that this modified procedures truly contributed to reduce the residual internal hemorrhoids and maintained the benefits of stapled hemorrhoidopexy. Randomized trial and long-term follow-up warrant to determine possible surgical and functional outcome.

Ground test facility for nuclear testing of space reactor subsystems

International Nuclear Information System (INIS)

Quapp, W.J.; Watts, K.D.

1985-01-01

Two major reactor facilities at the INEL have been identified as easily adaptable for supporting the nuclear testing of the SP-100 reactor subsystem. They are the Engineering Test Reactor (ETR) and the Loss of Fluid Test Reactor (LOFT). In addition, there are machine shops, analytical laboratories, hot cells, and the supporting services (fire protection, safety, security, medical, waste management, etc.) necessary to conducting a nuclear test program. This paper presents the conceptual approach for modifying these reactor facilities for the ground engineering test facility for the SP-100 nuclear subsystem. 4 figs

Effects of diesel fuel additives on engine performance and reliability. Part 2. Effects of lubricity additives; Keiyu tenkazai ga engine seino oyobi shinraisei ni ataeru eikyo. 2. Junkatsusei kojo ni yoru eikyo

Energy Technology Data Exchange (ETDEWEB)

Matsudaira, J; Okada, M; Naruse, H [Toyota Motor Corp., Aichi (Japan)

1997-10-01

Many studies about the effects of lublicity additives for diesel fuel have been carried out and reported. These additives have already been used in Europe, north-America for couple of years and it has just started in Japanese market this July. This paper mainly describes the effects of lublicity additives on engine performance and reliability. At first, the effects on engine reliability were investigated during 30 thousand kms chasis dynamometer test. Secondary, the effects on piston ring corrosion, injection nozzle fouling and water separation were investigated. Furthermore, 70 thousand kms engine reliability test was conducted, and investigated some component parts. 2 refs., 10 figs., 4 tabs.

Yttrium addition for high temperatures stainless steel

International Nuclear Information System (INIS)

Furtado, Nelson Cesar Chaves Pinto

1997-07-01

The current work studied the effect of Yttrium on the microstructure of 2% Nb, modified - HP steel, with respect to its mechanical properties. Alloys were prepared with nominal Yttrium additions of 0,1% and 0,25%. Microstructural analyses and mechanical tests were undertaken in the as-cast condition and after ageing for 100 h at 700 deg C, 900 deg C and 1100 deg C. Structural characterization was performed by optical microscopy, scanning and transmission electron microscopy (SEM/TEM/EDS), X-ray diffractometry and X-ray photoelectron spectroscopy (XPS). Tensile testing was performed at room temperature and 871 deg C and creep testing at 925 deg C at a loading of 55 MPa. The material produced exhibited superior mechanical properties and surface oxidation resistance than traditional alloys of this class, even through gravity cast in a magnetic furnace. Agglomerates of Yttrium-rich phases were identifies in both as-cast and aged specimens, always associated with chromium carbides of characteristic morphologies. These morphologies, combined with the microstructural constituents, may have established the factors which resulted in the improved metallurgical stability of these alloys under the experimental testing conditions and temperatures which simulated real industrial service conditions and temperatures. (author)

Low specificity and sensitivity of smell identification testing for the diagnosis of Parkinson?s disease

Directory of Open Access Journals (Sweden)

Mayela Rodríguez-Violante

Full Text Available Objective: The aim of this study is to determine if the University of Pennsylvania’s Smell Identification Test (UPSIT is an accurate diagnostic tool for olfactory dysfunction in Parkinson’s disease (PD. Method: We included 138 non-demented PD subjects and 175 control subjects matched by gender. Smell identification was tested using UPSIT. Results: The mean number of UPSIT items correctly identified by controls was 27.52±5.88; the mean score for PD subjects was 19.66±6.08 (p=<0.001. UPSIT sensitivity was 79.7% with a specificity of 68.5% using a cut-off score of ≤25. The overall accuracy for the diagnosis of PD was of 75.3%. Conclusion: UPSIT accuracy and specificity were lower than what has been previously reported. Our data demonstrates that 17.5% of items of the UPSIT were not well identified by healthy controls. Further research of the identification of a truly cross-cultural test is warranted.

Evaluation of Selected Borrelia burgdorferi lp54 Plasmid-Encoded Gene Products Expressed during Mammalian Infection as Antigens To Improve Serodiagnostic Testing for Early Lyme Disease

Science.gov (United States)

Weiner, Zachary P.; Crew, Rebecca M.; Brandt, Kevin S.; Ullmann, Amy J.; Schriefer, Martin E.; Molins, Claudia R.

2015-01-01

Laboratory testing for the diagnosis of Lyme disease is performed primarily by serologic assays and is accurate for detection beyond the acute stage of the infection. Serodiagnostic assays to detect the early stages of infection, however, are limited in their sensitivity, and improvement is warranted. We analyzed a series of Borrelia burgdorferi proteins known to be induced within feeding ticks and/or during mammalian infection for their utility as serodiagnostic markers against a comprehensive panel of Lyme disease patient serum samples. The antigens were assayed for IgM and IgG reactivity in line immunoblots and separately by enzyme-linked immunosorbent assay (ELISA), with a focus on reactivity against early Lyme disease with erythema migrans (EM), early disseminated Lyme neuroborreliosis, and early Lyme carditis patient serum samples. By IgM immunoblotting, we found that recombinant proteins BBA65, BBA70, and BBA73 reacted with early Lyme EM samples at levels comparable to those of the OspC antigen used in the current IgM blotting criteria. Additionally, these proteins reacted with serum samples from patients with early neuroborreliosis and early carditis, suggesting value in detecting early stages of this disease progression. We also found serological reactivity against recombinant proteins BBA69 and BBA73 with early-Lyme-disease samples using IgG immunoblotting and ELISA. Significantly, some samples that had been scored negative by the Centers for Disease Control and Prevention-recommended 2-tiered testing algorithm demonstrated positive reactivity to one or more of the antigens by IgM/IgG immunoblot and ELISA. These results suggest that incorporating additional in vivo-expressed antigens into the current IgM/IgG immunoblotting tier in a recombinant protein platform assay may improve the performance of early-Lyme-disease serologic testing. PMID:26376927

Evaluation of Selected Borrelia burgdorferi lp54 Plasmid-Encoded Gene Products Expressed during Mammalian Infection as Antigens To Improve Serodiagnostic Testing for Early Lyme Disease.

Science.gov (United States)

Weiner, Zachary P; Crew, Rebecca M; Brandt, Kevin S; Ullmann, Amy J; Schriefer, Martin E; Molins, Claudia R; Gilmore, Robert D

2015-11-01

Laboratory testing for the diagnosis of Lyme disease is performed primarily by serologic assays and is accurate for detection beyond the acute stage of the infection. Serodiagnostic assays to detect the early stages of infection, however, are limited in their sensitivity, and improvement is warranted. We analyzed a series of Borrelia burgdorferi proteins known to be induced within feeding ticks and/or during mammalian infection for their utility as serodiagnostic markers against a comprehensive panel of Lyme disease patient serum samples. The antigens were assayed for IgM and IgG reactivity in line immunoblots and separately by enzyme-linked immunosorbent assay (ELISA), with a focus on reactivity against early Lyme disease with erythema migrans (EM), early disseminated Lyme neuroborreliosis, and early Lyme carditis patient serum samples. By IgM immunoblotting, we found that recombinant proteins BBA65, BBA70, and BBA73 reacted with early Lyme EM samples at levels comparable to those of the OspC antigen used in the current IgM blotting criteria. Additionally, these proteins reacted with serum samples from patients with early neuroborreliosis and early carditis, suggesting value in detecting early stages of this disease progression. We also found serological reactivity against recombinant proteins BBA69 and BBA73 with early-Lyme-disease samples using IgG immunoblotting and ELISA. Significantly, some samples that had been scored negative by the Centers for Disease Control and Prevention-recommended 2-tiered testing algorithm demonstrated positive reactivity to one or more of the antigens by IgM/IgG immunoblot and ELISA. These results suggest that incorporating additional in vivo-expressed antigens into the current IgM/IgG immunoblotting tier in a recombinant protein platform assay may improve the performance of early-Lyme-disease serologic testing. Copyright © 2015, American Society for Microbiology. All Rights Reserved.

A review of the performance and structural considerations of paraffin wax hybrid rocket fuels with additives

Science.gov (United States)

Veale, Kirsty; Adali, Sarp; Pitot, Jean; Brooks, Michael

2017-12-01

Paraffin wax as a hybrid rocket fuel has not been comprehensively characterised, especially regarding the structural feasibility of the material in launch applications. Preliminary structural testing has shown paraffin wax to be a brittle, low strength material, and at risk of failure under launch loading conditions. Structural enhancing additives have been identified, but their effect on motor performance has not always been considered, nor has any standard method of testing been identified between research institutes. A review of existing regression rate measurement techniques on paraffin wax based fuels and the results obtained with various additives are collated and discussed in this paper. The review includes 2D slab motors that enable visualisation of liquefying fuel droplet entrainment and the effect of an increased viscosity on the droplet entrainment mechanism, which can occur with the addition of structural enhancing polymers. An increased viscosity has been shown to reduce the regression rate of liquefying fuels. Viscosity increasing additives that have been tested include EVA and LDPE. Both these additives increase the structural properties of paraffin wax, where the elongation and UTS are improved. Other additives, such as metal hydrides, aluminium and boron generally offer improvements on the regression rate. However, very little consideration has been given to the structural effects these additives have on the wax grain. A 40% aluminised grain, for example, offers a slight increase in the UTS but reduces the elongation of paraffin wax. Geometrically accurate lab-scale motors have also been used to determine the regression rate properties of various additives in paraffin wax. A concise review of all available regression rate testing techniques and results on paraffin wax based hybrid propellants, as well as existing structural testing data, is presented in this paper.

A Delphi Technology Foresight Study: Mapping Social Construction of Scientific Evidence on Metagenomics Tests for Water Safety.

Directory of Open Access Journals (Sweden)

Stanislav Birko

metagenomics rather than a co-productionist role at the "upstream" scientific design stage of metagenomics tests. In summary, these findings offer strategic foresight to govern metagenomics innovations symmetrically: by identifying areas where acceleration (e.g., consensus areas and deceleration/reconsideration (e.g., dissensus areas of the innovation trajectory might be warranted. Additionally, we show how scientific evidence is subject to potential social construction by experts' value systems and the need for greater upstream public engagement on metagenomics innovations.

Is it acceptable to use coagulation plasma samples stored at room temperature and 4°C for 24 hours for additional prothrombin time, activated partial thromboplastin time, fibrinogen, antithrombin, and D-dimer testing?

Science.gov (United States)

Rimac, V; Coen Herak, D

2017-10-01

Coagulation laboratories are faced on daily basis with requests for additional testing in already analyzed fresh plasma samples. This prompted us to examine whether plasma samples stored at room temperature (RT), and 4°C for 24 hours can be accepted for additional prothrombin time (PT), activated partial thromboplastin time (aPTT), fibrinogen (Fbg), antithrombin (AT), and D-dimer testing. We measured PT, aPTT, Fbg in 50 and AT in 30 plasma samples with normal and pathological values, within 4 hours of blood collection (baseline results) and after 24-hours storage at RT (primary tubes), and 4°C (aliquots). D-dimer stability was investigated in 20 samples stored in primary tubes at 4°C. No statistically significant difference between baseline results and results in samples stored at RT and 4°C was observed for PT (P=.938), aPTT (P=.186), Fbg (P=.962), AT (P=.713), and D-dimers (P=.169). The highest median percentage changes were found for aPTT, being more pronounced for samples stored at 4°C (13.0%) than at RT (8.7%). Plasma samples stored both at RT and 4°C for 24 hours are acceptable for additional PT, Fbg, and AT testing. Plasma samples stored 24 hours in primary tubes at 4°C are suitable for D-dimer testing. © 2017 John Wiley & Sons Ltd.

Radiolytic stabilization of poly(methyl methacrylate) using commercial additives

International Nuclear Information System (INIS)

Aquino, Katia Aparecida da Silva

2000-04-01

Poly(methyl methacrylate), PMMA, Acrigel, a Brazilian polymer, is used in the manufacture of medical supplies sterelizable by ionizing radiation. However, when PMMA is gamma-irradiated it undergoes main chain scissions, which promote molecular degradation causing reduction in its mechanical properties. Therefore, radiolytic of PMMA is important for it to become commercially radiosterizable. In this work some commercial additives, originally used in photo-and thermo-oxidate stabilization of polymers, were tested. Only two additives, type HALS (Hindered Amine Light Stabilizer), denoted Scavenger, showed a good protective quality. The investigation of radiation-induced main scissions was carried out by viscosimetric method. The most effective additive, added to the polymer system at 0.3 w/w%, promotes a great molecular radioprotection of 93%. That means a reduction of G-value (scissions/100 eV) from 0.611 to 0.053. In addition, the glassy transition temperature (T g ) of PMMA (no additive) significantly changed by radiation does not change when PMMA (with additive) is irradiated. The spectroscopy analysis, FT-IR and NMR ( 1 H), showed that the radioprotector added to the system does not change the PMMA structure. (author)

Do ultra-orphan medicinal products warrant ultra-high prices? A review

Directory of Open Access Journals (Sweden)

Picavet E

2013-06-01

Full Text Available Eline Picavet,1 David Cassiman,2 Steven Simoens1 1Department of Pharmaceutical and Pharmacological Sciences, KU Leuven, Leuven, Belgium; 2Department of Hepatology, University Hospital Leuven, Leuven, Belgium Abstract: Ultra-orphan medicinal products (ultra-OMPs are intended for the treatment, prevention, or diagnosis of ultra-rare diseases, ie, life-threatening or chronically debilitating diseases that affect less than one per 50,000 individuals. Recently, high prices for ultra-OMPs have given rise to debate on the sustainability and justification of these prices. The aim of this article is to review the international scientific literature on the pricing of ultra-OMPs and to provide an overview of the current knowledge on the drivers of ultra-OMP pricing. The pricing process of ultra-OMPs is a complex and nontransparent issue. Evidence in the literature seems to indicate that ultra-OMPs are priced according to rarity and what the manufacturer believes the market will bear. Additionally, there appears to be a trend between the price of an ultra-OMP and the number of available alternatives. Patients, third-party payers, and pharmaceutical companies could benefit from more transparent pricing strategies. With a view to containing health care costs, it is likely that cost-sharing strategies, such as performance-based risk sharing arrangements, will become increasingly more important. However, it is vital that any measures for price control are consistent with the intended goals of the incentives to promote the development of new OMPs. Ideally, a balance must be struck between attaining affordable prices for ultra-OMPs and securing a realistic return on investment for the pharmaceutical industry. Keywords: ultra-orphan medicinal product, ultra-rare disease, pricing

A study on the mechanical properties of additive manufactured polymer materials

Energy Technology Data Exchange (ETDEWEB)

Kim, Dong Bum; Lee, In Hwan; Cho, Hae Yong [Dept. of Mechanical Engineering, Chungbuk National University, Cheongju (Korea, Republic of)

2015-08-15

Traditionally, additive manufacturing (AM) technology has been used to fabricate prototypes in the early development phase of a product. This technology is being applied to release manufacturing of a product because of its low cost and fast fabrication. AM technology is a process of joining materials to fabricate a product from the 3D CAD data in a layer-by-layer manner. The orientation of a layer during manufacturing can affect the mechanical properties of the product because of its anisotropy. In this paper, tensile testing of polymer-based specimens were built with a typical AM process (FDM, PolyJet and SLA) to study the mechanical properties of the AM materials. The ASTM D 638 tensile testing standard was followed for building the specimens. The mechanical properties of the specimens were determined on the basis of stress-strain curves formed by tensile tests. In addition, the fracture surfaces of the specimens were observed by SEM to analyze the results.

Evaluation of the strength and radiopacity of Portland cement with varying additions of bismuth oxide.

Science.gov (United States)

Saliba, E; Abbassi-Ghadi, S; Vowles, R; Camilleri, J; Hooper, S; Camilleri, J

2009-04-01

To study the effect of addition of various proportions of bismuth oxide on compressive strength and radiopacity of Portland cement. The compressive strength of white Portland cement and cement replaced with 10, 15, 20, 25 and 30% bismuth oxide was evaluated by testing cylinders 6 mm in diameter and 12 mm high. Twelve cylinders were tested for each material under study. The radiopacity of the cements tested was evaluated using an aluminium step-wedge and densitometer. The optical density was compared with the relevant thickness of aluminium (Al). Statistical analysis was performed using Analysis of Variance (ANOVA) with P = 0.05 and Tukey test to perform multiple comparison tests. Various additions of bismuth oxide had no significant effect on the strength of the material when compared with the unmodified Portland cement (P > 0.05). The radiopacity of the cements tested ranged from 2.02 mm Al for Portland cement to 9.79 mm Al for the highest bismuth replacement. Addition of bismuth oxide did not affect the compressive strength of Portland cement. All the bismuth oxide cement mixtures had radio-opacities higher than 3 mm thickness of aluminium.

The effect of various pozzolanic additives on the concrete strength index

Science.gov (United States)

Vitola, L.; Sahmenko, G.; Erdmane, D.; Bumanis, G.; Bajare, D.

2017-10-01

The concrete industry is searching continuously for new effective mineral additives to improve the concrete properties. Replacing cement with the pozzolanic additives in most cases has resulted not only in positive impact on the environment but also has improved strength and durability of the concrete. Effective pozzolanic additives can be obtained from natural resources such as volcanic ashes, kaolin and other sediments as well as from different production industries that create various by-products with high pozzolanic reactivity. Current research deals with effectiveness evaluation of various mineral additives/wastes, such as coal combustion bottom ash, barley bottom ash, waste glass and metakaolin containing waste as well as calcined illite clays as supplementary cementitious materials, to be used in concrete production as partial cement replacement. Most of the examined materials are used as waste stream materials with potential reactive effect on the concrete. Milling time and fineness of the tested supplementary material has been evaluated and effectiveness was detected. Results indicate that fineness of the tested materials has crucial effect on the concrete compressive strength index. Not in all cases the prolonged milling time can increase fineness and reactivity of the supplementary materials; however the optimal milling time and fineness of the pozolanic additives increased the strength index of concrete up to 1.16 comparing to reference, even in cases when cement was substituted by 20 w%.

The Stimulus test stand

International Nuclear Information System (INIS)

Christofek, L.; Rapidis, P.; Reinhard, A.; Fermilab

2005-01-01

The Stimulus Test Stand was originally constructed and assembled for testing the SVX2 ASIC readout and then upgraded for SVX3 ASIC prototyping and testing. We have modified this system for SVX4 ASIC [1] prototype testing. We described the individual components below. Additional details for other hardware for SVX4 testing can be found in reference [2]. We provide a description of the Stimulus Test Stand used for prototype testing of the SVX4 chip

MECHANICAL PROPERTIES OF PARTS OF MEDICAL PRODUCTS PRODUCED USING ADDITIVE MANUFACTURING TECHNOLOGIES

Directory of Open Access Journals (Sweden)

Filip Górski

2017-06-01

Full Text Available The paper presents results of tests conducted on the elements of medical devices - slings used with medical lifts - manufactured using additive technologies. Project assumptions were: to produce 100 samples of clips with varying design, material and orientation parameter. Samples were manufactured using FDM and SLA processes and then tested for mechanical strength, load transmission and functionality, using certified equipment. Paper shows full methodology and obtained test results.

Testing statistical hypotheses

CERN Document Server

Lehmann, E L

2005-01-01

The third edition of Testing Statistical Hypotheses updates and expands upon the classic graduate text, emphasizing optimality theory for hypothesis testing and confidence sets. The principal additions include a rigorous treatment of large sample optimality, together with the requisite tools. In addition, an introduction to the theory of resampling methods such as the bootstrap is developed. The sections on multiple testing and goodness of fit testing are expanded. The text is suitable for Ph.D. students in statistics and includes over 300 new problems out of a total of more than 760. E.L. Lehmann is Professor of Statistics Emeritus at the University of California, Berkeley. He is a member of the National Academy of Sciences and the American Academy of Arts and Sciences, and the recipient of honorary degrees from the University of Leiden, The Netherlands and the University of Chicago. He is the author of Elements of Large-Sample Theory and (with George Casella) he is also the author of Theory of Point Estimat...

Effect of polymer additives on transition in pipe flow

Energy Technology Data Exchange (ETDEWEB)

Castro, W; Squire, W

1967-09-01

Small amounts of long-chain, water-soluble polymers have a marked effect on turbulent flow resulting in appreciable reduction of turbulent friction. The maximum reduction in pipe flow resistance is obtained at such low concentrations that the density and viscosity are not altered appreciably. The minimum friction curve varies as Re-2/3 and appears to be the same for all effective additives tested. The transition process is affected by these additives. Quantitative results are presented showing a reduction in the intensity of the turbulent flashes and the fraction of the time the flow is turbulent at a given Reynolds number. (13 refs.)

Strong correlation between the 6-minute walk test and accelerometry functional outcomes in boys with Duchenne muscular dystrophy.

Science.gov (United States)

Davidson, Zoe E; Ryan, Monique M; Kornberg, Andrew J; Walker, Karen Z; Truby, Helen

2015-03-01

Accelerometry provides information on habitual physical capability that may be of value in the assessment of function in Duchenne muscular dystrophy. This preliminary investigation describes the relationship between community ambulation measured by the StepWatch activity monitor and the current standard of functional assessment, the 6-minute walk test, in ambulatory boys with Duchenne muscular dystrophy (n = 16) and healthy controls (n = 13). All participants completed a 6-minute walk test and wore the StepWatch™ monitor for 5 consecutive days. Both the 6-minute walk test and StepWatch accelerometry identified a decreased capacity for ambulation in boys with Duchenne compared to healthy controls. There were strong, significant correlations between 6-minute walk distance and all StepWatch parameters in affected boys only (r = 0.701-0.804). These data proffer intriguing observations that warrant further exploration. Specifically, accelerometry outcomes may compliment the 6-minute walk test in assessment of therapeutic interventions for Duchenne muscular dystrophy. © The Author(s) 2014.

Immobilization of antimony in waste-to-energy bottom ash by addition of calcium and iron containing additives.

Science.gov (United States)

Van Caneghem, Jo; Verbinnen, Bram; Cornelis, Geert; de Wijs, Joost; Mulder, Rob; Billen, Pieter; Vandecasteele, Carlo

2016-08-01

The leaching of Sb from waste-to-energy (WtE) bottom ash (BA) often exceeds the Dutch limit value of 0.32mgkg(-1) for recycling of BA in open construction applications. From the immobilization mechanisms described in the literature, it could be concluded that both Ca and Fe play an important role in the immobilization of Sb in WtE BA. Therefore, Ca and Fe containing compounds were added to the samples of the sand fraction of WtE BA, which in contrast to the granulate fraction is not recyclable to date, and the effect on the Sb leaching was studied by means of batch leaching tests. Results showed that addition of 0.5 and 2.5% CaO, 5% CaCl2, 2.5% Fe2(SO4)3 and 1% FeCl3 decreased the Sb leaching from 0.62±0.02mgkgDM(-1) to 0.20±0.02, 0.083±0.044, 0.25±0.01, 0.27±0.002 and 0.29±0.02mgkgDM(-1), respectively. Due to the increase in pH from 11.41 to 12.53 when 2.5% CaO was added, Pb and Zn leaching increased and exceeded the respective leaching limits. Addition of 5% CaCO3 had almost no effect on the Sb leaching, as evidenced by the resulting 0.53mgkgDM(-1) leaching concentration. This paper shows a complementary enhancement of the effect of Ca and Fe, by comparing the aforementioned Sb leaching results with those of WtE BA with combined addition of 2.5% CaO or 5% CaCl2 with 2.5% Fe2(SO4)3 or 1% FeCl3. These lab scale results suggest that formation of romeites with a high Ca content and formation of iron antimonate (tripuhyite) with a very low solubility are the main immobilization mechanisms of Sb in WtE BA. Besides the pure compounds and their mixtures, also addition of 10% of two Ca and Fe containing residues of the steel industry, hereafter referred to as R1 and R2, was effective in decreasing the Sb leaching from WtE BA below the Dutch limit value for reuse in open construction applications. To evaluate the long term effect of the additives, pilot plots of WtE BA with 10% of R1 and 5% and 10% of R2 were built and samples were submitted to leaching tests at

Characterizations of additive manufactured porous titanium implants.

Science.gov (United States)

Basalah, Ahmad; Shanjani, Yaser; Esmaeili, Shahrzad; Toyserkani, Ehsan

2012-10-01

This article describes physical, chemical, and mechanical characterizations of porous titanium implants made by an additive manufacturing method to gain insight into the correlation of process parameters and final physical properties of implants used in orthopedics. For the manufacturing chain, the powder metallurgy technology was combined with the additive manufacturing to fabricate the porous structure from the pure tanium powder. A 3D printing machine was employed in this study to produce porous bar samples. A number of physical parameters such as titanium powder size, polyvinyl alcohol (PVA) amount, sintering temperature and time were investigated to control the mechanical properties and porosity of the structures. The produced samples were characterized through porosity and shrinkage measurements, mechanical compression test and scanning electron microscopy (SEM). The results showed a level of porosity in the samples in the range of 31-43%, which is within the range of the porosity of the cancelluous bone and approaches the range of the porosity of the cortical bone. The results of the mechanical test showed that the compressive strength is in the wide range of 56-509 MPa implying the effect of the process parameters on the mechanical strengths. This technique of manufacturing of Ti porous structures demonstrated a low level of shrinkage with the shrinkage percentage ranging from 1.5 to 5%. Copyright © 2012 Wiley Periodicals, Inc.

Alternative Test Method for Olefins in Gasoline

Science.gov (United States)

This action proposes to allow for an additional alternative test method for olefins in gasoline, ASTM D6550-05. The allowance of this additional alternative test method will provide more flexibility to the regulated industry.

Parameters of Alumina Cement and Portland Cement with Addition of Chalcedonite Meal

Science.gov (United States)

Kotwa, Anna

2017-10-01

Aluminous cement is a quick binder with special properties. It is used primarily to make non-standard monolithic components exposed to high temperatures, + 1300°C. It is also a component of adhesives and mortars. It has a very short setting time. It is characterized by rapid increase in mechanical strength and resistance to aggressive sulphates. It can be used in reinforced concrete structures. Laying of concrete, construction mortar made of alumina cement can be carried out even at temperatures of -10°C. This article discusses a comparison of the parameters of hardened mortar made of alumina cement GÓRKAL 40 and Portland cement CEM I 42.5R. The mortars contain an addition of chalcedonite meal with pozzolanic properties, with particle size of less than 0.063μm. The meal was added in amounts of 5% and 20% of cement weight. Chalcedonite meal used in the laboratory research is waste material, resulting from chalcedonite aggregate mining. It has the same properties as the rock from which it originates. We have compared the parameters of hardened mortar i.e. compressive strength, water absorption and capillarity. The addition of 20% chalcedonite meal to mortars made from aluminous cement will decrease durability by 6.1% relative to aluminous cement mortar without addition of meal. Considering the results obtained during the absorbency tests, it can be stated that the addition of chalcedonite meal reduces weight gains in mortars made with cement CEM I 42.5 R and alumina cement. Use of alumina cement without addition of meal in mortars causes an increase of mass by 248% compared to Portland cement mortars without additions, in the absorption tests. The addition of chalcedonite meal did not cause increased weight gain in the capillary action tests. For the alumina cement mortars, a lesser weight gains of 24.7% was reported, compared to the Portland cement mortar after 28 days of maturing.

Lab and Imaging Tests

Science.gov (United States)

... tests to help detect (diagnose) a blood cancer (leukemia, lymphoma, myeloma, myelodysplastic syndromes or myeloproliferative disease). You may need to undergo additional tests to confirm your diagnosis. Once your diagnosis is confirmed, your doctor may ...

THE INFLUENCE OF A HALLOYSITE ADDITIVE ON THE PERFORMANCE OF AUTOCLAVED AERATED CONCRETE

Directory of Open Access Journals (Sweden)

Z. Owsiak

2015-03-01

Full Text Available This paper presents the results from the tests of autoclaved aerated concrete with halloysite as a cement additive. Good pozzolanic properties make it a suitable material to be used as a partial replacement of a portion of cement. Basic physical and mechanical properties of the composites with various mineral content are discussed. The compressive strength test results indicate an increase in strength of the AAC containing 2.5 % and 5 % halloysite relative to the reference specimen. Thermal conductivity and density values remained at the same level. Observations of the microstructure in the scanning electron microscope confirmed the results from the XRD tests. Anhydrite was observed in addition to tobermorite. The results from the tests of the autoclaved aerated concretes in which halloysite was incorporated as 7.5 % and 10 % cement replacement showed an increase in compressive strength, density and thermal conductivity values.

Pilot testing of a burn prevention teaching tool for Amish children.

Science.gov (United States)

Rieman, Mary T; Kagan, Richard J

2012-01-01

Burn prevention education for Amish children is warranted as there are unique risks associated with the Amish lifestyle. Specific educational opportunities are related to scalds, ignition of clothing, and ignition of highly flammable materials. A culturally sensitive burn prevention teaching tool, consisting of a magnetic storyboard, burn safety curriculum, and tests, was developed with the cooperation of one Old Order Amish community. The purpose of this study was to test the effectiveness of the tool in an Amish school. The teacher obtained parental permission and informed assent for the participation of the children. Pretesting was completed before the lessons began. The teacher told stories and arranged the magnets on the storyboard to show burn hazards involving lighters, stoves, kerosene heaters, gasoline-powered engines, and hot liquids used for canning, butchering, mopping, washing clothes, and making lye soap. The children were challenged to rearrange the pieces for a safer situation. Posttesting was performed 2 months after the pretest. Twenty-seven students (grades 1-8) participated. Tests were scored as a percentage of the 33 items answered correctly. The mean pretest score was 62 and the mean posttest score was 83. Statistical analysis using paired t-test demonstrated a highly significant improvement in test scores (P < .0001), with a power of more than 99%. This pilot study demonstrated that the burn prevention teaching tool was effective for improving knowledge in one classroom of Amish children. These results support expanded use and testing of this tool in other Amish schools.

Food-additive-induced urticaria: a survey of 838 patients with recurrent chronic idiopathic urticaria.

Science.gov (United States)

Di Lorenzo, Gabriele; Pacor, Maria Luisa; Mansueto, Pasquale; Martinelli, Nicola; Esposito-Pellitteri, Maria; Lo Bianco, Claudia; Ditta, Vito; Leto-Barone, Maria Stefania; Napoli, Nicola; Di Fede, Gaetana; Rini, Giovambattista; Corrocher, Roberto

2005-11-01

Recurrent chronic idiopathic urticaria (RCIU) is a common skin condition that affects 0.1-3% of the population in the USA and Europe and accounts for nearly 75% of all 'ordinary' chronic urticaria (CU) cases. We studied 838 consecutive patients with RCIU referred to hospital between 1998 and 2003. Patients with known causes of CU were excluded. Clinical history, physical examination, and symptom diaries were evaluated during two periods, a diet-free period (1 week) and a food-additive-free diet (FAFD) period (4 weeks), respectively, and two double-blind placebo-controlled (DBPC) challenges of six food additives were administered. The first DBPC challenge included a mixture of the six food additives (DBPCmixed) given to all patients. The second DBPC challenge comprised the single food additives, administered at increasing doses (DBPCsingle) to patients with a positive DBPCmixed test and 105 patients with a negative DBPCmixed test, as a control. The DBPCmixed challenge was positive in 116 patients. None of the 105 control patients had a positive DBPCsingle test. Only 31 DBPCsingle tests were positive in patients with positive DBPCmixed challenge. Twenty-four of the 116 patients showing a positive DBPCmixed challenge also had a positive DBPCsingle result. Our results confirmed that food additive hypersensitivity reactions occurred in few RCIU patients using DBPCsingle challenge. The combination of the results of FAFD and DBPCmixed challenge seems to be of considerable practical interest for allergists, internists and dermatologists, rather than the data of clinical history and the results of DBPCsingle challenge, in patients with RCIU. Copyright (c) 2005 S. Karger AG, Basel.

Damage evolution and failure mechanisms in additively manufactured stainless steel

Energy Technology Data Exchange (ETDEWEB)

Carlton, Holly D., E-mail: carlton4@llnl.gov [Materials Engineering Division, Lawrence Livermore National Laboratory, 7000 East Avenue, Livermore, CA 94550 (United States); Haboub, Abdel [Lincoln University, Life and Physical Sciences Department, 820 Chestnut St, Jefferson City, MO 65101 (United States); Gallegos, Gilbert F. [Materials Engineering Division, Lawrence Livermore National Laboratory, 7000 East Avenue, Livermore, CA 94550 (United States); Parkinson, Dilworth Y.; MacDowell, Alastair A. [Advanced Light Source, Lawrence Berkeley National Laboratory, 1 Cyclotron Road, Berkeley, CA 94720 (United States)

2016-01-10

In situ tensile tests were performed on additively manufactured austenitic stainless steel to track damage evolution within the material. For these experiments Synchrotron Radiation micro-Tomography was used to measure three-dimensional pore volume, distribution, and morphology in stainless steel at the micrometer length-scale while tensile loading was applied. The results showed that porosity distribution played a larger role in affecting the fracture mechanisms than measured bulk density. Specifically, additively manufactured stainless steel specimens with large inhomogeneous void distributions displayed a flaw-dominated failure where cracks were shown to initiate at pre-existing voids, while annealed additively manufactured stainless steel specimens, which contained low porosity and randomly distributed pores, displayed fracture mechanisms that closely resembled wrought metal.

Statistical study of chemical additives effects in the waste cementation

International Nuclear Information System (INIS)

Tello, Cledola C.O. de; Diniz, Paula S.; Haucz, Maria J.A.

1997-01-01

This paper presents the statistical study, that was carried out to analyse the chemical additives effect in the waste cementation process. Three different additives from two industries were tested: set accelerator, set retarder and super plasticizers, in cemented pates with and without bentonite. The experiments were planned in accordance with the 2 3 factorial design, so that the effect of each type of additive, its quantity and manufacturer in cemented paste and specimens could be evaluated. The results showed that the use of these can improve the cementation process and the product. The admixture quantity and the association with bentonite were the most important factors affecting the process and product characteristics. (author). 4 refs., 9 figs., 4 tabs

Litter Decomposition in a Semiarid Dune Grassland: Neutral Effect of Water Supply and Inhibitory Effect of Nitrogen Addition.

Directory of Open Access Journals (Sweden)

Yulin Li

Full Text Available The decomposition of plant material in arid ecosystems is considered to be substantially controlled by water and N availability. The responses of litter decomposition to external N and water, however, remain controversial, and the interactive effects of supplementary N and water also have been largely unexamined.A 3.5-year field experiment with supplementary nitrogen and water was conducted to assess the effects of N and water addition on mass loss and nitrogen release in leaves and fine roots of three dominant plant species (i.e., Artemisia halondendron, Setaria viridis, and Phragmites australis with contrasting substrate chemistry (e.g. N concentration, lignin content in this study in a desertified dune grassland of Inner Mongolia, China. The treatments included N addition, water addition, combination of N and water, and an untreated control. The decomposition rate in both leaves and roots was related to the initial litter N and lignin concentrations of the three species. However, litter quality did not explain the slower mass loss in roots than in leaves in the present study, and thus warrant further research. Nitrogen addition, either alone or in combination with water, significantly inhibited dry mass loss and N release in the leaves and roots of the three species, whereas water input had little effect on the decomposition of leaf litter and fine roots, suggesting that there was no interactive effect of supplementary N and water on litter decomposition in this system. Furthermore, our results clearly indicate that the inhibitory effects of external N on dry mass loss and nitrogen release are relatively strong in high-lignin litter compared with low-lignin litter.These findings suggest that increasing precipitation hardly facilitates ecosystem carbon turnover but atmospheric N deposition can enhance carbon sequestration and nitrogen retention in desertified dune grasslands of northern China. Additionally, litter quality of plant species

Litter Decomposition in a Semiarid Dune Grassland: Neutral Effect of Water Supply and Inhibitory Effect of Nitrogen Addition.

Science.gov (United States)

Li, Yulin; Ning, Zhiying; Cui, Duo; Mao, Wei; Bi, Jingdong; Zhao, Xueyong

2016-01-01

The decomposition of plant material in arid ecosystems is considered to be substantially controlled by water and N availability. The responses of litter decomposition to external N and water, however, remain controversial, and the interactive effects of supplementary N and water also have been largely unexamined. A 3.5-year field experiment with supplementary nitrogen and water was conducted to assess the effects of N and water addition on mass loss and nitrogen release in leaves and fine roots of three dominant plant species (i.e., Artemisia halondendron, Setaria viridis, and Phragmites australis) with contrasting substrate chemistry (e.g. N concentration, lignin content in this study) in a desertified dune grassland of Inner Mongolia, China. The treatments included N addition, water addition, combination of N and water, and an untreated control. The decomposition rate in both leaves and roots was related to the initial litter N and lignin concentrations of the three species. However, litter quality did not explain the slower mass loss in roots than in leaves in the present study, and thus warrant further research. Nitrogen addition, either alone or in combination with water, significantly inhibited dry mass loss and N release in the leaves and roots of the three species, whereas water input had little effect on the decomposition of leaf litter and fine roots, suggesting that there was no interactive effect of supplementary N and water on litter decomposition in this system. Furthermore, our results clearly indicate that the inhibitory effects of external N on dry mass loss and nitrogen release are relatively strong in high-lignin litter compared with low-lignin litter. These findings suggest that increasing precipitation hardly facilitates ecosystem carbon turnover but atmospheric N deposition can enhance carbon sequestration and nitrogen retention in desertified dune grasslands of northern China. Additionally, litter quality of plant species should be considered

Detection of additive outliers in seasonal time series

DEFF Research Database (Denmark)

Haldrup, Niels; Montañés, Antonio; Sansó, Andreu

The detection and location of additive outliers in integrated variables has attracted much attention recently because such outliers tend to affect unit root inference among other things. Most of these procedures have been developed for non-seasonal processes. However, the presence of seasonality......) to deal with data sampled at a seasonal frequency and the size and power properties are discussed. We also show that the presence of periodic heteroscedasticity will inflate the size of the tests and hence will tend to identify an excessive number of outliers. A modified Perron-Rodriguez test which allows...... periodically varying variances is suggested and it is shown to have excellent properties in terms of both power and size...

Clinical, social and ethical issues associated with non-invasive prenatal testing for aneuploidy.

Science.gov (United States)

Griffin, Blanche; Edwards, Samantha; Chitty, Lyn S; Lewis, Celine

2018-03-01

Non-invasive prenatal testing (NIPT), based on analysis of cell-free foetal DNA, is rapidly becoming a preferred method to screen for chromosomal aneuploidy with the technology now available in over 90 countries. This review provides an up-to-date discussion of the key clinical, social and ethical implications associated with this revolutionary technology. Stakeholders are positive about a test that is highly accurate, safe, can be perfomed early in pregnancy, identifies affected pregnancies that might otherwise have been missed and reduces the need for invasive testing. Nevertheless, professional societies currently recommend it as an advanced screening test due to the low false positive rate (FPR). Despite the practical and psychological benefits, a number of concerns have been raised which warrant attention. These include the potential for routinisation of testing and subsequent impact on informed decision-making, an "easy" blood test inadvertently contributing to women feeling pressured to take the test, fears NIPT will lead to less tolerance and support for those living with Down syndrome and the heightened expectation of having "perfect babies". These issues can be addressed to some extent through clinician education, patient information and establishing national and international consensus in the development of comprehensive and regularly updated guidelines. As the number of conditions we are able to test for non-invasively expands it will be increasingly important to ensure pre-test counselling can be delivered effectively supported by knowledgeable healthcare professionals.

The European Arrest Warrant in the Italian legal system. Between mutual recognition and mutual fear within the European area of Freedom, Security and Justice

Directory of Open Access Journals (Sweden)

Franco Impalà

2005-12-01

Full Text Available Italy was the last Member State to transpose the Framework Decision on the European Arrest Warrant. The Italian law entered into full force on 14 May 2005, a full sixteen months later than the appointed date. Conversely, whilst the Framework Decision aimed to speed up extradition between Member States, the Italian implementation law seems to complicate things, providing for dozens of new legal obstacles to surrender. In fact, the execution of an EAW in Italy threatens to become something highly unpredictable. The responsibility for this outcome is shared by the national and the European legislator. Perhaps the latter underestimated the seriousness of the conflict between Third Pillar law and domestic constitutional systems which aim to protect their acquis in the field of fundamental rights. Considering that many Member States seem to be struggling with similar problems, the first part of this article is devoted to describing the current scenario and analysing possible solutions at the supranational level, such as the establishment of a coherent system regulating the allocation of penal competences among Member States. In the next part, the problem of the Framework Decision’s incompatibility with the Italian Constitution will be discussed, and in the final part the Italian implementation law is analysed in more detail.

Resilient modulus characteristics of soil subgrade with geopolymer additive in peat

Science.gov (United States)

Zain, Nasuhi; Hadiwardoyo, Sigit Pranowo; Rahayu, Wiwik

2017-06-01

Resilient modulus characteristics of peat soil are generally very low with high potential of deformation and low bearing capacity. The efforts to improve the peat subgrade resilient modulus characteristics is required, one among them is by adding the geopolymer additive. Geopolymer was made as an alternative to replace portland cement binder in the concrete mix in order to promote environmentally friendly, low shrinkage value, low creep value, and fire resistant material. The use of geopolymer to improve the mechanical properties of peat as a road construction subgrade, hence it becomes important to identify the effect of geopolymer addition on the resilient modulus characteristics of peat soil. This study investigated the addition of 0% - 20% geopolymer content on peat soil derived from Ogan Komering Ilir, South Sumatera Province. Resilient modulus measurement was performed by using cyclic triaxial test to determine the resilience modulus model as a function of deviator stresses and radial stresses. The test results showed that an increase in radial stresses did not necessarily lead to an increase in modulus resilient, and on the contrary, an increase in deviator stresses led to a decrease in modulus resilient. The addition of geopolymer in peat soil provided an insignificant effect on the increase of resilient modulus value.

Pilot-scale testing of renewable biocatalyst for swine manure treatment and mitigation of odorous VOCs, ammonia and hydrogen sulfide emissions

Science.gov (United States)

Maurer, Devin L.; Koziel, Jacek A.; Bruning, Kelsey; Parker, David B.

2017-02-01

Comprehensive control of odors, hydrogen sulfide (H2S), ammonia (NH3), and greenhouse gas (GHG) emissions associated with swine production is a critical need. A pilot-scale experiment was conducted to evaluate surface-applied soybean peroxidase (SBP) and calcium peroxide (CaO2) as a manure additive to mitigate emissions of odorous volatile organic compounds (VOC) including dimethyl disulfide/methanethiol (DMDS/MT), dimethyl trisulfide, n-butyric acid, valeric acid, isovaleric acid, p-cresol, indole, and skatole. The secondary impact on emissions of NH3, H2S, and GHG was also measured. The SBP was tested at four treatments (2.28-45.7 kg/m2 manure) with CaO2 (4.2% by weight of SBP) over 137 days. Significant reductions in VOC emissions were observed: DMDS/MT (36.2%-84.7%), p-cresol (53.1%-89.5%), and skatole (63.2%-92.5%). There was a corresponding significant reduction in NH3 (14.6%-67.6%), and significant increases in the greenhouse gases CH4 (32.7%-232%) and CO2 (20.8%-124%). The remaining emissions (including N2O) were not statistically different. At a cost relative to 0.8% of a marketed hog it appears that SBP/CaO2 treatment could be a promising option at the lowest (2.28 kg/m2) treatment rate for reducing odorous gas and NH3 emissions at swine operations, and field-scale testing is warranted.

Emissions from a Diesel Engine using Fe-based Fuel Additives and a Sintered Metal Filtration System.

Science.gov (United States)

Bugarski, Aleksandar D; Hummer, Jon A; Stachulak, Jozef S; Miller, Arthur; Patts, Larry D; Cauda, Emanuele G

2016-03-01

A series of laboratory tests were conducted to assess the effects of Fe-containing fuel additives on aerosols emitted by a diesel engine retrofitted with a sintered metal filter (SMF) system. Emission measurements performed upstream and downstream of the SMF system were compared, for cases when the engine was fueled with neat ultralow sulfur diesel (ULSD) and with ULSD treated with two formulations of additives containing Fe-based catalysts. The effects were assessed for four steady-state engine operating conditions and one transient cycle. The results showed that the SMF system reduced the average total number and surface area concentrations of aerosols by more than 100-fold. The total mass and elemental carbon results confirmed that the SMF system was indeed very effective in the removal of diesel aerosols. When added at the recommended concentrations (30 p.p.m. of iron), the tested additives had minor adverse impacts on the number, surface area, and mass concentrations of filter-out (FOut) aerosols. For one of the test cases, the additives may have contributed to measurable concentrations of engine-out (EOut) nucleation mode aerosols. The additives had only a minor impact on the concentration and size distribution of volatile and semi-volatile FOut aerosols. Metal analysis showed that the introduction of Fe with the additives substantially increased Fe concentration in the EOut, but the SMF system was effective in removal of Fe-containing aerosols. The FOut Fe concentrations for all three tested fuels were found to be much lower than the corresponding EOut Fe concentrations for the case of untreated ULSD fuel. The results support recommendations that these additives should not be used in diesel engines unless they are equipped with exhaust filtration systems. Since the tested SMF system was found to be very efficient in removing Fe introduced by the additives, the use of these additives should not result in a measurable increase in emissions of de novo generated

Results of scoping tests for open-cycle OTEC (ocean thermal energy conversion) components operating with seawater

Energy Technology Data Exchange (ETDEWEB)

Zangrando, F; Bharathan, D; Green, H J; Link, H F; Parsons, B K; Parsons, J M; Pesaran, A A [Solar Energy Research Inst., Golden, CO (USA); Panchal, C B [Argonne National Lab., IL (USA)

1990-09-01

This report presents comprehensive documentation of the experimental research conducted on open-cycle ocean thermal energy conversion (OC-OTEC) components operating with seawater as a working fluid. The results of this research are presented in the context of previous analysis and fresh-water testing; they provide a basis for understanding and predicting with confidence the performance of all components of an OC-OTEC system except the turbine. Seawater tests have confirmed the results that were obtained in fresh-water tests and predicted by the analytical models of the components. A sound technical basis has been established for the design of larger systems in which net power will be produced for the first time from OC-OTEC technology. Design and operation of a complete OC-OTEC system that produces power will provide sufficient confidence to warrant complete transfer of OC-OTEC technology to the private sector. Each components performance is described in a separate chapter written by the principal investigator responsible for technical aspects of the specific tests. Chapters have been indexed separately for inclusion on the data base.

Reduced turning frequency and delayed poultry manure addition reduces N loss from sugarcane compost

DEFF Research Database (Denmark)

Bryndum, Sofie; Muschler, R.; Nigatu, Abebe Nigussie

2017-01-01

Composting is an effective method to recycle biodegradable waste as soil amendment in smallholder farming systems. Although all essential plant nutrients are found in compost, a substantial amount of nitrogen is lost during composting. This study therefore investigated the potential of reducing N...... losses by (i) delaying the addition of nitrogen-rich substrates (i.e. poultry manure), and (ii) reducing the turning frequency during composting. Furthermore, we tested the effect of compost application method on nitrogen mineralization. Sugarcane-waste was composted for 54days with addition of poultry...... manure at the beginning (i.e. early addition) or after 21days of composting (delayed addition). The compost pile was then turned either every three or nine days. Composts were subsequently applied to soil as (i) homogeneously mixed, or (ii) stratified, and incubated for 28days to test the effect...

Significance of Glucose Addition on Chitosan-Glycerophosphate Hydrogel Properties

Directory of Open Access Journals (Sweden)

Dian Susanthy

2016-03-01

Full Text Available Chitosan-glycerophosphate hydrogel can be used as dental scaffold due to its thermosensitivity, gelation performance at body temperature, suitable acidity for body condition, biocompatibility, and ability to provide good environment for cell proliferation and differentiation. Previous study showed that glucose addition to the chitosan solution before steam sterilization improved its hydrogel mechanical strength. However, the effectiveness of glucose addition was still doubted because glucose might undergo Maillard reaction in that particular condition. The aims of this study are to confirm whether the glucose addition can increase the hydrogel mechanical strength and gelation rate effectively and also to compare their performance to be dental scaffold. This research was performed through several steps, namely preparation of chitosan-glycerophosphate solution, addition of glucose, gelation time test, gel mechanical strength measurement, functional group analysis, and physical properties measurements (pH, viscosity, and pore size. The result showed that glucose addition did not improve the hydrogel mechanical strength and gelation rate, neither when it was added before nor after steam sterilization. Glucose addition before steam sterilization seemed to trigger Maillard reaction or browning effect, while glucose addition after steam sterilization increased the amount of free water molecules in the hydrogel. Chitosan and glycerophosphate interact physically, but interaction between chitosan and glucose seems to occur chemically and followed by the formation of free water molecules. Glucose addition decreases the solution viscosity and hydrogel pore size so the hydrogel performance as dental scaffold is lowered.

MONOSODIUM TITANATE MULTI-STRIKE TESTING

International Nuclear Information System (INIS)

BARNES, MARKJ

2004-01-01

Research over the past decade has studied the adsorption of plutonium and uranium onto monosodium titanate (MST) in alkaline solutions. Tests showed that MST would remove the targeted radionuclides from simulated alkaline waste. Testing also indicated that Pu removal kinetics and Np capacity of the MST material impacts the size of equipment and waste blending plans for the Salt Waste Processing Facility (SWPF). Additionally, calculations suggested the baseline MST process may not achieve the desired decontamination in wastes containing elevated concentrations of Pu and Np. In this task, the authors investigated the performance of non-baseline process parameters and their effectiveness for treating waste feed in the Salt Waste Processing Facility. The work addresses a DOE request in support of technical needs expressed, in part, by the Engineering, Procurement, and Construction Contractors for the Salt Waste Processing Facility. The work investigated the effect of increased MST addition (up to 1.2 g/L) and the benefit of extra filtration steps with multiple additions of MST to salt waste containing actinides and strontium. Both simulant and actual waste testing occurred. Actual waste tests used a Tank 39H composite waste solution. In addition, testing to determine desorption of actinides from residual MST occurred. The release of sorbed Sr and actinides from loaded MST during the washing stages in the Salt Waste Processing Facility is an unresolved process behavior. Desorption tests assessed this potential problem using loaded MST from the residue of the MST adsorption tests. Analysis of non-radioactive Sr in the tests proved difficult due to the low concentration of nonradioactive Sr and its nearness to the method detection limit for ICP-MS. Efforts to use AMP to minimize dilution of actual waste for removal from the cell did not help for this analysis since instrument dilution still proved necessary due to the salt content

In vitro bonding effectiveness of three different one-step self-etch adhesives with additional enamel etching.

Science.gov (United States)

Batra, Charu; Nagpal, Rajni; Tyagi, Shashi Prabha; Singh, Udai Pratap; Manuja, Naveen

2014-08-01

To evaluate the effect of additional enamel etching on the shear bond strength of three self-etch adhesives. Class II box type cavities were made on extracted human molars. Teeth were randomly divided into one control group of etch and rinse adhesive and three test groups of self-etch adhesives (Clearfil S3 Bond, Futurabond NR, Xeno V). The teeth in the control group (n = 10) were treated with Adper™ Single Bond 2. The three test groups were further divided into two subgroups (n = 10): (i) self-etch adhesive was applied as per the manufacturer's instructions; (ii) additional etching of enamel surfaces was done prior to the application of self-etch adhesives. All cavities were restored with Filtek Z250. After thermocycling, shear bond strength was evaluated using a Universal testing machine. Data were analyzed using anova independent sample's 't' test and Dunnett's test. The failure modes were evaluated with a stereomicroscope at a magnification of 10×. Additional phosphoric acid etching of the enamel surface prior to the application of the adhesive system significantly increased the shear bond strength of all the examined self-etch adhesives. Additional phosphoric acid etching of enamel surface significantly improved the shear bond strength. © 2013 Wiley Publishing Asia Pty Ltd.

Honeywell Cascade Distiller System Performance Testing Interim Results

Science.gov (United States)

Callahan, Michael R.; Sargusingh, Miriam

2014-01-01

The ability to recover and purify water through physiochemical processes is crucial for realizing long-term human space missions, including both planetary habitation and space travel. Because of their robust nature, distillation systems have been actively pursued as one of the technologies for water recovery. The Cascade Distillation System (CDS) is a vacuum rotary distillation system with potential for greater reliability and lower energy costs than existing distillation systems. The CDS was previously under development through Honeywell and NASA. In 2009, an assessment was performed to collect data to support down-selection and development of a primary distillation technology for application in a lunar outpost water recovery system. Based on the results of this testing, an expert panel concluded that the CDS showed adequate development maturity, TRL-4, together with the best product water quality and competitive weight and power estimates to warrant further development. The Advanced Exploration Systems (AES) Water Recovery Project (WRP) worked to address weaknesses identified by The Panel; namely bearing design and heat pump power efficiency. Testing at the NASA-JSC Advanced Exploration System Water Laboratory (AES Water Lab) using a prototype Cascade Distillation Subsystem (CDS) wastewater processor (Honeywell International, Torrance, Calif.) with test support equipment and control system developed by Johnson Space Center was performed to evaluate performance of the system with the upgrades. The CDS will also have been challenged with ISS analog waste streams and a subset of those being considered for Exploration architectures. This paper details interim results of the AES WRP CDS performance testing.

Frictional properties of lubrication greases with the addition of nickel nanoparticles in pneumatic cylinder

Science.gov (United States)

Chang, Ho; Lan, Chou-Wei; Guo, Jia-Bin

2011-12-01

This paper studies the influence of addition of 100 nm diameter nickel nano-particles on the friction properties of synthetic grease (Li base, VG100) in pneumatic cylinder. The friction force test of pneumatic cylinder equipment measures the frictional force between seal and cylinder bore in pneumatic cylinders. The lubricants with addition of nickel nano-particles were used for lubricating the contact interface between seal and cylinder bore. The friction force test equipment employ a load cell force sensor to measure the friction force between seals and cylinder bores. Results obtained from experimental tests are compared to determine the friction force between seals and cylinder bore in pneumatic cylinders. The study leads to the conclusion that the addition of nickel nano-particles to synthetic grease results in a decrease in friction force between seals and cylinder bores in pneumatic cylinder. This tribological behavior is closely related to the deposition of nano-particles on the rubbing surfaces

Cathodic protection -- Addition of 6 anodes to existing rectifier 31

International Nuclear Information System (INIS)

Lane, W.M.

1995-01-01

This Acceptance Test Procedure (ATP) has been prepared to demonstrate that the cathodic protection system additions are installed, connected, and function as required by project criteria. The cathodic protection system is for the tank farms on the Hanford Reservation. The tank farms store radioactive wastes

PENINGKATAN KADAR GERANIOL DALAM MINYAK SEREH WANGI DAN APLIKASINYA SEBAGAI BIO ADDITIVE GASOLINE

Directory of Open Access Journals (Sweden)

Widi Astuti

2014-10-01

by 5.36%. The content can be increase using vacuum distillation  up to 21.78 % at temperature of 120oC. The citronella oil test as a gasoline bio additive including  performance test and fuel efficiency test with gasoline-bio additive ratio as variable. The addition of citronella oil to gasoline with the volume ratio of gasoline : citronella oil = 1000:2  increases machine power from 7.8 HP to 8.6 HP and fuel efficiency up to 10.8 %.

Additive manufacturing.

Science.gov (United States)

Mumith, A; Thomas, M; Shah, Z; Coathup, M; Blunn, G

2018-04-01

Increasing innovation in rapid prototyping (RP) and additive manufacturing (AM), also known as 3D printing, is bringing about major changes in translational surgical research. This review describes the current position in the use of additive manufacturing in orthopaedic surgery. Cite this article: Bone Joint J 2018;100-B:455-60.

The cost efficiency of exploratory testing:ISTQB certified testing compared with RST

OpenAIRE

Niittyviita, S. (Sampo)

2017-01-01

Abstract The research of software testing and the practices of software testing in the industry are separated by gaps in some areas. One such gap regards Exploratory Testing (ET). ET is probably the most widely used software testing approach in the industry, yet it is lacking research and many of the manuals of software engineering either ignore or look down on it. In addition, ET has the absence of widespread methodology a...

Comparison of presbyopic additions determined by the fused cross-cylinder method using alternative target background colours.

Science.gov (United States)

Wee, Sung-Hyun; Yu, Dong-Sik; Moon, Byeong-Yeon; Cho, Hyun Gug

2010-11-01

To compare and contrast standard and alternative versions of refractor head (phoropter)-based charts used to determine reading addition. Forty one presbyopic subjects aged between 42 and 60 years were tested. Tentative additions were determined using a red-green background letter chart, and 4 cross-grid charts (with white, red, green, or red-green backgrounds) which were used with the fused cross cylinder (FCC) method. The final addition for a 40 cm working distance was determined for each subject by subjectively adjusting the tentative additions. There were significant differences in the tentative additions obtained using the 5 methods (repeated measures ANOVA, p FCC method. There were no significant differences between the tentative and final additions for the green background in the FCC method (p > 0.05). The intervals of the 95% limits of agreement were under ±0.50 D, and the narrowest interval (±0.26 D) was for the red-green background. The 3 FCC methods with a white, green, or red-green background provided a tentative addition close to the final addition. Compared with the other methods, the FCC method with the red-green background had a narrow range of error. Further, since this method combines the functions of both the fused cross-cylinder test and the duochrome test, it can be a useful technique for determining presbyopic additions. © 2010 The Authors. Ophthalmic and Physiological Optics © 2010 The College of Optometrists.

Disintegration Test of Health Food Products Containing Ginkgo Biloba L. or Vitex Agnus-Castus L. in the Japanese Market

Science.gov (United States)

Sato-Masumoto, Naoko; Masada, Sayaka; Takahashi, Satoshi; Terasaki, Sachiko; Yokota, Yoichi; Hakamatsuka, Takashi; Goda, Yukihiro

2015-01-01

For many years now, a number of Western herbs have been widely used in health food products in Japan and as pharmaceuticals in Europe. There are few or no mandated criteria concerning the quality of these herbal health food products, thus clarification is warranted. Here, we performed disintegration tests of 26 pharmaceutical and health food products containing the Western herbs ginkgo leaf and chaste tree fruit, in accord with the Japanese Pharmacopoeia. All eight pharmaceutical herbal products found in the European market completely disintegrated within the defined test time, and 11 of the 18 tested herbal products distributed as health foods in Japan disintegrated. Among the incompatible products identified in the Pharmacopoeia test, some products remained intact after incubation in water for 60 min. To ensure the efficacy of Western herbal products sold as health food in Japan, quality control, including disintegration, is therefore recommended, even though these products are not regulated under the Pharmaceutical Affairs Law. PMID:28930200

Disintegration Test of Health Food Products Containing Ginkgo Biloba L. or Vitex Agnus-Castus L. in the Japanese Market.

Science.gov (United States)

Sato-Masumoto, Naoko; Masada, Sayaka; Takahashi, Satoshi; Terasaki, Sachiko; Yokota, Yoichi; Hakamatsuka, Takashi; Goda, Yukihiro

2015-04-23

For many years now, a number of Western herbs have been widely used in health food products in Japan and as pharmaceuticals in Europe. There are few or no mandated criteria concerning the quality of these herbal health food products, thus clarification is warranted. Here, we performed disintegration tests of 26 pharmaceutical and health food products containing the Western herbs ginkgo leaf and chaste tree fruit, in accord with the Japanese Pharmacopoeia. All eight pharmaceutical herbal products found in the European market completely disintegrated within the defined test time, and 11 of the 18 tested herbal products distributed as health foods in Japan disintegrated. Among the incompatible products identified in the Pharmacopoeia test, some products remained intact after incubation in water for 60 min. To ensure the efficacy of Western herbal products sold as health food in Japan, quality control, including disintegration, is therefore recommended, even though these products are not regulated under the Pharmaceutical Affairs Law.

The behaviour of molybdenum dialkyldithiocarbamate friction modifier additives

International Nuclear Information System (INIS)

Graham, Jocelyn Claire Herries

2001-01-01

In recent years there has been growing concern to produce energy-efficient lubricated components and modem engine oil specifications require lubricants to demonstrate fuel efficiency in standardised engine tests. One important method of producing low friction and thus fuel-efficient lubricants is to use oil-soluble, molybdenum-containing, friction modifier additives. In optimal conditions these additives are able to produce very low friction coefficients, in the range 0.045 to 0.075 in boundary lubrication conditions. Very little is known about the chemical and physical mechanisms by which oil soluble molybdenum additives form low friction films in tribological contacts. Information about their activity could lead to optimal use of these additives in lubricants and, therefore, more efficient engine running. The work outlined in this thesis investigated the behaviour of oil-soluble molybdenum additives and showed that these additives were able to effectively reduce friction in the absence of other additives such as ZnDTP. Their activity was shown to be highly concentration and temperature dependent and was also found to be sensitive to the roughness of the contacting surfaces. Raman spectroscopy was used to analyse the chemical nature of molybdenum-containing reaction films and found that friction reduction indubitably arises from the local formation of platelets (diameter 30-50 nm) of MoS 2 . The formation of MoS 2 -rich films was found to occur only during direct asperity-asperity rubbing of the contacting surfaces (this type of contact being especially prevalent in pure sliding contacts). At elevated temperatures and in the presence of oxidising gases the consumption of MoDTC was monitored. MoDTC concentration dropped until the total value fell below a critical level to reduce friction. The study showed that decay rate of molybdenum-containing species was reduced by the addition of peroxide-decomposing antioxidants. (author)

Irradiation effects test Series Scoping Test 1: test results report

International Nuclear Information System (INIS)

Quapp, W.J.; Allison, C.M.; Farrar, L.C.

1977-09-01

The report describes the results of the first scoping test in the Irradiation Effects Test Series conducted by the Thermal Fuels Behavior Program, which is part of the Water Reactor Research Program of EG and G Idaho, Inc. The research is sponsored by the United States Nuclear Regulatory Commission. This test used an unirradiated, three-foot-long, PWR-type fuel rod. The objective of this test was to thoroughly evaluate the remote fabrication procedures to be used for irradiated rods in future tests, handling plans, and reactor operations. Additionally, selected fuel behavior data were obtained. The fuel rod was subjected to a series of preconditioning power cycles followed by a power increase which brought the fuel rod power to about 20.4 kW/ft peak linear heat rating at a coolant mass flux of 1.83 x 10 6 lb/hr-ft 2 . Film boiling occurred for a period of 4.8 minutes following flow reductions to 9.6 x 10 5 and 7.5 x 10 5 lb/hr-ft 2 . The test fuel rod failed following reactor shutdown as a result of heavy internal and external cladding oxidation and embrittlement which occurred during the film boiling operation

A computer vision based candidate for functional balance test.

Science.gov (United States)

Nalci, Alican; Khodamoradi, Alireza; Balkan, Ozgur; Nahab, Fatta; Garudadri, Harinath

2015-08-01

Balance in humans is a motor skill based on complex multimodal sensing, processing and control. Ability to maintain balance in activities of daily living (ADL) is compromised due to aging, diseases, injuries and environmental factors. Center for Disease Control and Prevention (CDC) estimate of the costs of falls among older adults was $34 billion in 2013 and is expected to reach $54.9 billion in 2020. In this paper, we present a brief review of balance impairments followed by subjective and objective tools currently used in clinical settings for human balance assessment. We propose a novel computer vision (CV) based approach as a candidate for functional balance test. The test will take less than a minute to administer and expected to be objective, repeatable and highly discriminative in quantifying ability to maintain posture and balance. We present an informal study with preliminary data from 10 healthy volunteers, and compare performance with a balance assessment system called BTrackS Balance Assessment Board. Our results show high degree of correlation with BTrackS. The proposed system promises to be a good candidate for objective functional balance tests and warrants further investigations to assess validity in clinical settings, including acute care, long term care and assisted living care facilities. Our long term goals include non-intrusive approaches to assess balance competence during ADL in independent living environments.

Polymer X-ray refractive nano-lenses fabricated by additive technology.

Science.gov (United States)

Petrov, A K; Bessonov, V O; Abrashitova, K A; Kokareva, N G; Safronov, K R; Barannikov, A A; Ershov, P A; Klimova, N B; Lyatun, I I; Yunkin, V A; Polikarpov, M; Snigireva, I; Fedyanin, A A; Snigirev, A

2017-06-26

The present work demonstrates the potential applicability of additive manufacturing to X-Ray refractive nano-lenses. A compound refractive lens with a radius of 5 µm was produced by the two-photon polymerization induced lithography. It was successfully tested at the X-ray microfocus laboratory source and a focal spot of 5 μm was measured. An amorphous nature of polymer material combined with the potential of additive technologies may result in a significantly enhanced focusing performance compared to the best examples of modern X-ray compound refractive lenses.

Combustion Performance of a Staged Hybrid Rocket with Boron addition

Science.gov (United States)

Lee, D.; Lee, C.

2018-04-01

In this paper, the effect of boron on overall system specific impulse was investigated. Additionally, a series of combustion tests was carried out to analyze and evaluate the effect of boron addition on O/F variation and radial temperature profiles. To maintain the hybrid rocket engine advantages, upper limit of boron contents in solid fuel was set to be 10 wt%. The results also suggested that, when adding boron to solid fuel, it helped to provide more uniform radial temperature distribution and also to increase specific impulse by 3.2%.

Irradiation performance of coated fuel particles with fission product retaining kernel additives

International Nuclear Information System (INIS)

Foerthmann, R.

1979-10-01

The four irradiation experiments FRJ2-P17, FRJ2-P18, FRJ2-P19, and FRJ2-P20 for testing the efficiency of fission product-retaining kernel additives in coated fuel particles are described. The evaluation of the obtained experimental data led to the following results: - zirconia and alumina kernel additives are not suitable for an effective fission product retention in oxide fuel kernels, - alumina-silica kernel additives reduce the in-pile release of Sr 90 and Ba 140 from BISO-coated particles at temperatures of about 1200 0 C by two orders of magnitude, and the Cs release from kernels by one order of magnitude, - effective transport coefficients including all parameters which contribute to kernel release are given for (Th,U)O 2 mixed oxide kernels and low enriched UO 2 kernels containing 5 wt.% alumina-silica additives: 10g sub(K)/cm 2 s -1 = - 36 028/T + 6,261 (Sr 90), 10g Dsub(K)/cm 2 c -2 = - 29 646/T + 5,826 (Cs 134/137), alumina-silica kernel additives are ineffective for retaining Ag 110 m in coated particles. However, also an intact SiC-interlayer was found not to be effective at temperatures above 1200 0 C, - the penetration of the buffer layer by fission product containing eutectic additive melt during irradiation can be avoided by using additives which consist of alumina and mullite without an excess of silica, - annealing of LASER-failed irradiated particles and the irradiation test FRJ12-P20 indicate that the efficiency of alumina-silica kernel additives is not altered if the coating becomes defect. (orig.) [de

Test-Retest Reliability of the Short-Form Survivor Unmet Needs Survey.

Science.gov (United States)

Taylor, Karen; Bulsara, Max; Monterosso, Leanne

2018-01-01

Reliable and valid needs assessment measures are important assessment tools in cancer survivorship care. A new 30-item short-form version of the Survivor Unmet Needs Survey (SF-SUNS) was developed and validated with cancer survivors, including hematology cancer survivors; however, test-retest reliability has not been established. The objective of this study was to assess the test-retest reliability of the SF-SUNS with a cohort of lymphoma survivors ( n = 40). Test-retest reliability of the SF-SUNS was conducted at two time points: baseline (time 1) and 5 days later (time 2). Test-retest data were collected from lymphoma cancer survivors ( n = 40) in a large tertiary cancer center in Western Australia. Intraclass correlation analyses compared data at time 1 (baseline) and time 2 (5 days later). Cronbach's alpha analyses were performed to assess the internal consistency at both time points. The majority (23/30, 77%) of items achieved test-retest reliability scores 0.45-0.74 (fair to good). A high degree of overall internal consistency was demonstrated (time 1 = 0.92, time 2 = 0.95), with scores 0.65-0.94 across subscales for both time points. Mixed test-retest reliability of the SF-SUNS was established. Our results indicate the SF-SUNS is responsive to the changing needs of lymphoma cancer survivors. Routine use of cancer survivorship specific needs-based assessments is required in oncology care today. Nurses are well placed to administer these assessments and provide tailored information and resources. Further assessment of test-retest reliability in hematology and other cancer cohorts is warranted.

Cleaning Process Development for Metallic Additively Manufactured Parts

Science.gov (United States)

Tramel, Terri L.; Welker, Roger; Lowery, Niki; Mitchell, Mark

2014-01-01

Additive Manufacturing of metallic components for aerospace applications offers many advantages over traditional manufacturing techniques. As a new technology, many aspects of its widespread utilization remain open to investigation. Among these are the cleaning processes that can be used for post finishing of parts and measurements to verify effectiveness of the cleaning processes. Many cleaning and drying processes and measurement methods that have been used for parts manufactured using conventional techniques are candidates that may be considered for cleaning and verification of additively manufactured parts. Among these are vapor degreasing, ultrasonic immersion and spray cleaning, followed by hot air drying, vacuum baking and solvent displacement drying. Differences in porosity, density, and surface finish of additively manufactured versus conventionally manufactured parts may introduce new considerations in the selection of cleaning and drying processes or the method used to verify their effectiveness. This presentation will review the relative strengths and weaknesses of different candidate cleaning and drying processes as they may apply to additively manufactured metal parts for aerospace applications. An ultrasonic cleaning technique for exploring the cleanability of parts will be presented along with an example using additively manufactured Inconel 718 test specimens to illustrate its use. The data analysis shows that this ultrasonic cleaning approach results in a well-behaved ultrasonic cleaning/extraction behavior. That is, it does not show signs of accelerated cavitation erosion of the base material, which was later confirmed by neutron imaging. In addition, the analysis indicated that complete cleaning would be achieved by ultrasonic immersion cleaning at approximately 5 minutes, which was verified by subsequent cleaning of additional parts.

Effect Of Formulating Additives On The Properties Of Ibuprofen Tablets

African Journals Online (AJOL)

A study of the comparative effects of different formulating additives and film coating on the properties of ibuprofen tablets was made. The tested properties were hardeness (H), friability (F), the disintegration time (D) and dissolution characteristics of ibuprofen tablets. The hardeness, friability, the hardeness friability ratio ...

The Impact of Additive on the Properties of Fresh and Hardened Mortar

Directory of Open Access Journals (Sweden)

Jurga Šeputytė

2012-11-01

Full Text Available This paper considers the impact of additives on the properties of mortar. For investigation purposes, two types of Portland cement (CEM II/A-LL 42.5 N and CEM I N (MA, fine aggregate sand, lime, water and air-entraining and stabilizing additives were used. To determine the effects of additives on the mortar mix, the analysis of cone penetration into the mix, mortar mobility, water extraction out of mortar, density and flexural and compressive testing were conducted. When put into mortar, air-entraining and stabilizing additives changed structure. In this case, density and flexural and compressive strength of mortar are reduced.

Retention Load of Telescopic Crowns with Different Taper Angles between Cobalt-Chromium and Polyetheretherketone Made with Three Different Manufacturing Processes Examined by Pull-Off Test.

Science.gov (United States)

Wagner, Christina; Stock, Veronika; Merk, Susanne; Schmidlin, Patrick R; Roos, Malgorzata; Eichberger, Marlis; Stawarczyk, Bogna

2018-02-01

To investigate the retention loads of differently fabricated secondary telescopic polyetheretherketone (PEEK) crowns on cobalt-chromium primary crowns with different tapers. Cobalt-chromium primary crowns with 0°, 1°, and 2° tapers were constructed, milled, and sintered. Corresponding secondary crowns were fabricated by milling, pressing from pellets, and pressing from granules. For these nine test groups, the pull-off tests of each crown combination were performed 20 times, and the retention loads were measured (Zwick 1445, 50 mm/min). Data were analyzed using linear regression, covariance analysis, mixed models, Kruskal-Wallis, and Mann-Whitney U-test, together with the Benferroni-Holm correction. The mixed models covariance analysis reinforced stable retention load values (p = 0.162) for each single test sequence. There was no interaction between the groups and the separation cycles (p = 0.179). Milled secondary crowns with 0° showed the lowest mean retention load values compared to all tested groups (p = 0.003) followed by those pressed form pellets with 1°. Regarding the different tapers, no effect of manufacturing method on the results was observed within 1° and 2° groups (p = 0.540; p = 0.052); however, among the 0° groups, the milled ones showed significantly the lowest retention load values (p = 0.002). Among the manufacturing methods, both pressed groups showed no impact of taper on the retention load values (p > 0.324 and p > 0.123, respectively), whereas among the milled secondary crowns, the 0° taper showed significantly lower retention load values than the 1° and 2° taper (p test sequence; however, data with thermo-mechanical aging are still required. In addition, further developments in CAD/CAM manufacturing of PEEK materials for telescopic crowns are warranted, especially for 0°. © 2016 by the American College of Prosthodontists.

Efficacy of feed additives to reduce the effect of naturally occurring mycotoxins fed to turkey hen poults reared to 6 weeks of age.

Science.gov (United States)

Tilley, J E N; Grimes, J L; Koci, M D; Ali, R A; Stark, C R; Nighot, P K; Middleton, T F; Fahrenholz, A C

2017-12-01

Corn with naturally occurring aflatoxin (AF), wheat with naturally occurring doxynivalenol (DON), and barley with naturally occurring zearalenone (ZEA) were used to make rations for feeding turkey hen poults to 6 weeks of age. Control rations with equal amounts of corn, wheat, and barley were also fed. The control rations did contain some DON while both sets of rations contained ZEA. Within each grain source, there were 4 treatments: the control ration plus 3 rations each with a different feed additive which were evaluated for the potential to lessen potential mycotoxin effects on bird performance and physiology. The additives were Biomin BioFix (2 lb/ton), Kemin Kallsil (4 lb/ton), and Nutriad UNIKE (3 lb/ton). The mycotoxin rations reduced poult body weight (2.31 vs. 2.08 ± 0.02 kg) and increased (worsened) poult feed conversion (1.47 vs. 1.51 ± 0.01) at 6 wk. Feeding the poults the mycotoxin feed also resulted in organ and physiological changes typical of feeding dietary aflatoxin although a combined effect of AF, DON, and ZEA which cannot be dismissed. The feed additives resulted in improved feed conversion to 6 wk in both grain treatment groups. The observed physiological effect of feeding the additives was to reduce relative gizzard weight for both groups and to lessen the increase in relative kidney weight for the birds fed the mycotoxin feed. In conclusion, the feed additives used in this study did alleviate the effect of dietary mycotoxins to some degree, especially with respect to feed conversion. Further studies of longer duration are warranted. © 2017 Poultry Science Association Inc.

Large-scale academic achievement testing of deaf and hard-of-hearing students: past, present, and future.

Science.gov (United States)

Qi, Sen; Mitchell, Ross E

2012-01-01

The first large-scale, nationwide academic achievement testing program using Stanford Achievement Test (Stanford) for deaf and hard-of-hearing children in the United States started in 1969. Over the past three decades, the Stanford has served as a benchmark in the field of deaf education for assessing student academic achievement. However, the validity and reliability of using the Stanford for this special student population still require extensive scrutiny. Recent shifts in educational policy environment, which require that schools enable all children to achieve proficiency through accountability testing, warrants a close examination of the adequacy and relevance of the current large-scale testing of deaf and hard-of-hearing students. This study has three objectives: (a) it will summarize the historical data over the last three decades to indicate trends in academic achievement for this special population, (b) it will analyze the current federal laws and regulations related to educational testing and special education, thereby identifying gaps between policy and practice in the field, especially identifying the limitations of current testing programs in assessing what deaf and hard-of-hearing students know, and (c) it will offer some insights and suggestions for future testing programs for deaf and hard-of-hearing students.

The use of standardised short-term and working memory tests in aphasia research: a systematic review.

Science.gov (United States)

Murray, Laura; Salis, Christos; Martin, Nadine; Dralle, Jenny

2018-04-01

Impairments of short-term and working memory (STM, WM), both verbal and non-verbal, are ubiquitous in aphasia. Increasing interest in assessing STM and WM in aphasia research and clinical practice as well as a growing evidence base of STM/WM treatments for aphasia warrant an understanding of the range of standardised STM/WM measures that have been utilised in aphasia. To date, however, no previous systematic review has focused on aphasia. Accordingly, the goals of this systematic review were: (1) to identify standardised tests of STM and WM utilised in the aphasia literature, (2) to evaluate critically the psychometric strength of these tests, and (3) to appraise critically the quality of the investigations utilising these tests. Results revealed that a very limited number of standardised tests, in the verbal and non-verbal domains, had robust psychometric properties. Standardisation samples to elicit normative data were often small, and most measures exhibited poor validity and reliability properties. Studies using these tests inconsistently documented demographic and aphasia variables essential to interpreting STM/WM test outcomes. In light of these findings, recommendations are provided to foster, in the future, consistency across aphasia studies and confidence in STM/WM tests as assessment and treatment outcome measures.

D-OPTIMAL EXPERIMENTAL DESIGNS TO TEST FOR DEPARTURE FROM ADDITIVITY IN A FIXED-RATIO MIXTURE RAY.

Science.gov (United States)

Humans are exposed to mixtures of environmental compounds. A regulatory assumption is that the mixtures of chemicals act in an additive manner. However, this assumption requires experimental validation. Traditional experimental designs (full factorial) require a large number of e...

Total laboratory automation: Do stat tests still matter?

Science.gov (United States)

Dolci, Alberto; Giavarina, Davide; Pasqualetti, Sara; Szőke, Dominika; Panteghini, Mauro

2017-07-01

During the past decades the healthcare systems have rapidly changed and today hospital care is primarily advocated for critical patients and acute treatments, for which laboratory test results are crucial and need to be always reported in predictably short turnaround time (TAT). Laboratories in the hospital setting can face this challenge by changing their organization from a compartmentalized laboratory department toward a decision making-based laboratory department. This requires the implementation of a core laboratory, that exploits total laboratory automation (TLA) using technological innovation in analytical platforms, track systems and information technology, including middleware, and a number of satellite specialized laboratory sections cooperating with care teams for specific medical conditions. In this laboratory department model, the short TAT for all first-line tests performed by TLA in the core laboratory represents the key paradigm, where no more stat testing is required because all samples are handled in real-time and (auto)validated results dispatched in a time that fulfills clinical needs. To optimally reach this goal, laboratories should be actively involved in managing all the steps covering the total examination process, speeding up also extra-laboratory phases, such sample delivery. Furthermore, to warrant effectiveness and not only efficiency, all the processes, e.g. specimen integrity check, should be managed by middleware through a predefined set of rules defined in light of the clinical governance. Crown Copyright © 2017. Published by Elsevier Inc. All rights reserved.

Reflooding phenomena of German PWR estimated from CCTF [Cylindrical Core Test Facility], SCTF [Slab Core Test Facility] and UPTF [Upper Plenum Test Facility] results

International Nuclear Information System (INIS)

Murao, Y.; Iguchi, T.; Sugimoto, J.

1988-09-01

The reflooding behavior in a PWR with a combined injection type ECCS was studied by comparing the test results from Cylindrical Core Test Facility (CCTF), Slab Core Test Facility (SCTF) and Upper Plenum Test Facility (UPTF). Core thermal-hydraulics is discussed mainly based on SCTF test data. In addition, the water accumulation behavior in hot legs and the break-through characteristics at tie plate are discussed

Survey of chemical compounds tested in vitro against rumen protozoa for possible control of bloat.

Science.gov (United States)

Willard, F L; Kodras, R

1967-09-01

Over 170 chemical agents were screened for antiprotozoal action in bovine ruminal fluid. Compounds were tested at 0.1 and 0.05% concentrations. Tested compounds included inorganic compounds, antibiotics, biocides, neuromuscular agents, arsenicals, plant and animal hormones, antimalarials, surface-active agents, anthelmintics, and many others. The most active compounds were cupric sulfate, nickel sulfate, nitrofurazone, hydrogen peroxide, dodecyl sodium sulfate, pelargonic acid, iodoacetic acid, 1-diethylaminoethylamino-4-methylthiaxanthrone, sodium arsanilate, sodium arsenate, bismuth glycolyl arsanilate, 1-beta-hydroxyethyl-2-methyl-5-nitroimidazole, and p-nitroaniline. Copper ion was not particularly effective against entodinia; nickel ion had no effect on holotrichs. Hydrogen peroxide and iodoacetic acid were effective at a concentration of 0.005%. Anionic surface-active agents were very effective, especially long-chain sulfates and phosphates. These antiprotozoal agents warrant further in vivo studies for possible use in treating or curing bloat in ruminants.

Transcatheter Arterial Embolization for Upper Gastrointestinal Nonvariceal Hemorrhage: Is Empiric Embolization Warranted?

Energy Technology Data Exchange (ETDEWEB)

Arrayeh, Elnasif; Fidelman, Nicholas, E-mail: nicholas.fidelman@ucsf.edu; Gordon, Roy L.; LaBerge, Jeanne M.; Kerlan, Robert K. [University of California San Francisco, Department of Radiology (United States); Klimov, Alexander; Bloom, Allan I. [Hadassah Hospital, Department of Radiology (Israel)

2012-12-15

Purpose: To determine whether transcatheter arterial embolization performed in the setting of active gastric or duodenal nonvariceal hemorrhage is efficacious when the bleeding source cannot be identified angiographically. Methods: Records of 115 adult patients who underwent visceral angiography for endoscopically documented gastric (50 patients) or duodenal (65 patients) nonvariceal hemorrhage were retrospectively reviewed. Patients were subdivided into three groups according to whether angiographic evidence of arterial hemorrhage was present and whether embolization was performed (group 1 = no abnormality, no embolization; group 2 = no abnormality, embolization performed [empiric embolization]; and group 3 = abnormality present, embolization performed). Thirty-day rates and duration of primary hemostasis and survival were compared.ResultsFor patients with gastric sources of hemorrhage, the rate of primary hemostasis at 30 days after embolization was greater when embolization was performed in the setting of a documented angiographic abnormality than when empiric embolization was performed (67% vs. 42%). The rate of primary hemostasis at 30 days after angiography was greater for patients with duodenal bleeding who either underwent empiric embolization (60%) or embolization in the setting of angiographically documented arterial hemorrhage (58%) compared with patients who only underwent diagnostic angiogram (33%). Patients with duodenal hemorrhage who underwent embolization were less likely to require additional invasive procedures to control rebleeding (p = 0.006). Conclusion: Empiric arterial embolization may be advantageous in patients with a duodenal source of hemorrhage but not in patients with gastric hemorrhage.

Experimentation on bio-kerosene stove using organic additive

Science.gov (United States)

Varshini, M.; Shetty, Divakar

2017-07-01

One of the basic worthy item used in most of the villages even now a day's also is the kerosene stove. But in the current scenario, the petroleum products are been replenished. So an alternate fuel should be found in order delve. This work is to check the contingency of blending pongamia oil and kerosene in which is used as an additive. Pongamia is one of the forest based fast growing evergreen tree which is capable of yielding 9 - 90 kg seeds from which 25% of oil can be extracted. Distilled cow urine is to be used so that the fuel can be stored for longer time and is odorless. Blends of 10% to 70% neat pongamia oil - kerosene(KEP) and pongamia oil - kerosene with additive(KEPWA) are prepared. The properties such as flash point, fire point and viscosity are determined. The blends are been compared by doing emission test. The blends with additive showed better properties and reducing in emission characteristics compared to neat blends. It is also observed that emission of CO is decreasing with increasing blends.

The effects of chemical additives on the production of disinfection byproducts and ecotoxicity in simulated ballast water

Science.gov (United States)

Park, Chul; Cha, Hyung-Gon; Lee, Ji-Hyun; Choi, Tae Seop; Lee, Jungsuk; Kim, Young-Hee; Bae, Minjung; Shin, Kyoungsoon; Choi, Keun-Hyung

2017-11-01

The management of ship ballast water is essential to stemming the introduction of non-indigenous species. Approval for onboard installation of a system to treat ballast water requires rigorous land-based testing as dictated in the G8 guideline by the International Maritime Organization. However, this testing lacks standardization-most notably augmentation of organic carbon for influent water by adding chemical additives. Electrochlorination is a popular treatment method for ballast water, in which chlorinated oxidants react with organisms and organic matter in water. The additives could thus affect the treatment efficacy of the ballast water. Here, we examined the effects of several candidates of organic carbon additives on the consumption of total residual oxidant (TRO), the production of disinfection byproducts (DBPs), plankton survival, and ecotoxicity. The TRO consumption over five days of storage was higher in electrochlorinated seawater amended with lignin and Metamucil when compared with seawaters with other organic carbon compounds. DBP production varied by almost two orders of magnitude as a function of the various additives. This was largely attributed to the production of tribromomethane and dibromoacetic acid. The survival of Artemia franciscana was significantly different across waters of different organic carbon additives. Algal toxicity testing with the marine haptophyte Isochrysis galbana significantly reduced growth in lignin- and Metamucil-treated seawaters, but not with other organic carbon compounds. Bioluminescence in Vibrio fischeri sharply declined in electrochlorinated seawaters with all types of organic carbon compounds, but no toxicity was manifested once the electrochlorinated seawaters were neutralized with sodium thiosulfate. The varying degrees of outcome suggest that it might be better to eliminate the requirements of adding organic carbon to test water as long as natural water was used for land-based testing of BWMS. If needed, the

Testing of badminton specific endurance

DEFF Research Database (Denmark)

Madsen, Christian Møller; Højlyng, Mads; Nybo, Lars

2016-01-01

In the present study, a novel intermittent badminton endurance test (B-ENDURANCE) was developed and tested in elite (n=17) and skilled (n=9) badminton players as well as in age-matched physically active men (non-badminton players; n=8). In addition, B-ENDURANCE test-retest reproducibility...... was evaluated in nine badminton players.B-ENDURANCE is an incremental test where each level consists of repeated sequences of badminton specific actions towards the four corners on the court. The subject starts in the center of the court in front of a computer screen and within each sequence he must...... decreases until the subjects cannot follow the dictated tempo.B-ENDURANCE performance for elite players was better (Pbadminton players. In addition, B-ENDURANCE performance correlated (r=0.8; P

Testing a computer-based ostomy care training resource for staff nurses.

Science.gov (United States)

Bales, Isabel

2010-05-01

Fragmented teaching and ostomy care provided by nonspecialized clinicians unfamiliar with state-of-the-art care and products have been identified as problems in teaching ostomy care to the new ostomate. After conducting a literature review of theories and concepts related to the impact of nurse behaviors and confidence on ostomy care, the author developed a computer-based learning resource and assessed its effect on staff nurse confidence. Of 189 staff nurses with a minimum of 1 year acute-care experience employed in the acute care, emergency, and rehabilitation departments of an acute care facility in the Midwestern US, 103 agreed to participate and returned completed pre- and post-tests, each comprising the same eight statements about providing ostomy care. F and P values were computed for differences between pre- and post test scores. Based on a scale where 1 = totally disagree and 5 = totally agree with the statement, baseline confidence and perceived mean knowledge scores averaged 3.8 and after viewing the resource program post-test mean scores averaged 4.51, a statistically significant improvement (P = 0.000). The largest difference between pre- and post test scores involved feeling confident in having the resources to learn ostomy skills independently. The availability of an electronic ostomy care resource was rated highly in both pre- and post testing. Studies to assess the effects of increased confidence and knowledge on the quality and provision of care are warranted.

Foliar Potassium Fertilizer Additives Affect Soybean Response and Weed Control with Glyphosate

Directory of Open Access Journals (Sweden)

Kelly A. Nelson

2012-01-01

Full Text Available Research in 2004 and 2005 determined the effects of foliar-applied K-fertilizer sources (0-0-62-0 (%N-%P2O5-%K2O-%S, 0-0-25-17, 3-18-18-0, and 5-0-20-13 and additive rates (2.2, 8.8, and 17.6 kg K ha−1 on glyphosate-resistant soybean response and weed control. Field experiments were conducted at Novelty and Portageville with high soil test K and weed populations and at Malden with low soil test K and weed populations. At Novelty, grain yield increased with fertilizer additives at 8.8 kg K ha−1 in a high-yield, weed-free environment in 2004, but fertilizer additives reduced yield up to 470 kg ha−1 in a low-yield year (2005 depending on the K source and rate. At Portageville, K-fertilizer additives increased grain yield from 700 to 1160 kg ha−1 compared to diammonium sulfate, depending on the K source and rate. At Malden, there was no yield response to K sources. Differences in leaf tissue K (P=0.03, S (P=0.03, B (P=0.0001, and Cu (P=0.008 concentrations among treatments were detected 14 d after treatment at Novelty and Malden. Tank mixtures of K-fertilizer additives with glyphosate may provide an option for foliar K applications.

Chicken feather fiber as an additive in MDF composites

Science.gov (United States)

Jerrold E. Winandy; James H. Muehl; Jessie A. Glaeser; Walter Schmidt

2007-01-01

Medium density fiberboard (MDF) panels were made with aspen fiber and 0-95% chicken feather fiber (CFF) in 2.5%, 5%, or 25% increments, using 5% phenol formaldehyde resin as the adhesive. Panels were tested for mechanical and physical properties as well as decay. The addition of CFF decreased strength and stiffness of MDF-CFF composites compared with that of all-wood...

GHS additivity formula: can it predict the acute systemic toxicity of agrochemical formulations that contain acutely toxic ingredients?

Science.gov (United States)

Van Cott, Andrew; Hastings, Charles E; Landsiedel, Robert; Kolle, Susanne; Stinchcombe, Stefan

2018-02-01

In vivo acute systemic testing is a regulatory requirement for agrochemical formulations. GHS specifies an alternative computational approach (GHS additivity formula) for calculating the acute toxicity of mixtures. We collected acute systemic toxicity data from formulations that contained one of several acutely-toxic active ingredients. The resulting acute data set includes 210 formulations tested for oral toxicity, 128 formulations tested for inhalation toxicity and 31 formulations tested for dermal toxicity. The GHS additivity formula was applied to each of these formulations and compared with the experimental in vivo result. In the acute oral assay, the GHS additivity formula misclassified 110 formulations using the GHS classification criteria (48% accuracy) and 119 formulations using the USEPA classification criteria (43% accuracy). With acute inhalation, the GHS additivity formula misclassified 50 formulations using the GHS classification criteria (61% accuracy) and 34 formulations using the USEPA classification criteria (73% accuracy). For acute dermal toxicity, the GHS additivity formula misclassified 16 formulations using the GHS classification criteria (48% accuracy) and 20 formulations using the USEPA classification criteria (36% accuracy). This data indicates the acute systemic toxicity of many formulations is not the sum of the ingredients' toxicity (additivity); but rather, ingredients in a formulation can interact to result in lower or higher toxicity than predicted by the GHS additivity formula. Copyright © 2018 Elsevier Inc. All rights reserved.

Ultrasonic assessment of additive manufactured Ti-6Al-4V

Science.gov (United States)

Schehl, Norman; Kramb, Vicki; Dierken, Josiah; Aldrin, John; Schwalbach, Edwin; John, Reji

2018-04-01

Additive Manufacturing (AM) processes offer the potential for manufacturing cost savings and rapid insertion into service through production of near net shape components for complicated structures. Use of these parts in high reliability applications such as those in the aerospace industry will require nondestructive characterization methods to ensure post-process material quality in as-built condition. Ultrasonic methods can be used for this quality verification. Depending on the application, the service life of AM components can be sensitive to the part surface condition. The surface roughness and layered structure inherent to the electron-beam powder-bed fusion process necessitates new approaches to evaluate subsurface material integrity in its presence. Experimental methods and data analytics may improve the evaluation of as-built additively manufactured materials. This paper discusses the assessment of additively manufactured EBM Ti-6Al-4V panels using ultrasonic methods and the data analytics applied to evaluate material integrity. The assessment was done as an exploratory study as the discontinuities of interest in these test samples were not known when the measurements were performed. Water immersion ultrasonic techniques, including pulse-echo and through transmission with 10 MHz focused transducers, were used to explore the material integrity of as-built plates. Subsequent destructive mechanical tests of specimens extracted from the plates provided fracture locations indicating critical flaws. To further understand the effect of surface-roughness, an evaluation of ultrasonic response in the presence of as-built surfaces and with the surface removed was performed. The assessment of additive manufactured EBM Ti-6Al-4V panels with ultrasonic techniques indicated that ultrasonic energy was attenuated by the as-built surface roughness. In addition, feature detection was shown to be sensitive to experimental ultrasonic parameters and flaw morphology.

Non-hydrostatic semi-elastic hybrid-coordinate SISL extension of HIRLAM. Part II: numerical testing

Science.gov (United States)

Rõõm, Rein; Männik, Aarne; Luhamaa, Andres; Zirk, Marko

2007-10-01

The semi-implicit semi-Lagrangian (SISL), two-time-level, non-hydrostatic numerical scheme, based on the non-hydrostatic, semi-elastic pressure-coordinate equations, is tested in model experiments with flow over given orography (elliptical hill, mountain ridge, system of successive ridges) in a rectangular domain with emphasis on the numerical accuracy and non-hydrostatic effect presentation capability. Comparison demonstrates good (in strong primary wave generation) to satisfactory (in weak secondary wave reproduction in some cases) consistency of the numerical modelling results with known stationary linear test solutions. Numerical stability of the developed model is investigated with respect to the reference state choice, modelling dynamics of a stationary front. The horizontally area-mean reference temperature proves to be the optimal stability warrant. The numerical scheme with explicit residual in the vertical forcing term becomes unstable for cross-frontal temperature differences exceeding 30 K. Stability is restored, if the vertical forcing is treated implicitly, which enables to use time steps, comparable with the hydrostatic SISL.

Additive Manufacturing Design Considerations for Liquid Engine Components

Science.gov (United States)

Whitten, Dave; Hissam, Andy; Baker, Kevin; Rice, Darron

2014-01-01

The Marshall Space Flight Center's Propulsion Systems Department has gained significant experience in the last year designing, building, and testing liquid engine components using additive manufacturing. The department has developed valve, duct, turbo-machinery, and combustion device components using this technology. Many valuable lessons were learned during this process. These lessons will be the focus of this presentation. We will present criteria for selecting part candidates for additive manufacturing. Some part characteristics are 'tailor made' for this process. Selecting the right parts for the process is the first step to maximizing productivity gains. We will also present specific lessons we learned about feature geometry that can and cannot be produced using additive manufacturing machines. Most liquid engine components were made using a two-step process. The base part was made using additive manufacturing and then traditional machining processes were used to produce the final part. The presentation will describe design accommodations needed to make the base part and lessons we learned about which features could be built directly and which require the final machine process. Tolerance capabilities, surface finish, and material thickness allowances will also be covered. Additive Manufacturing can produce internal passages that cannot be made using traditional approaches. It can also eliminate a significant amount of manpower by reducing part count and leveraging model-based design and analysis techniques. Information will be shared about performance enhancements and design efficiencies we experienced for certain categories of engine parts.

75 FR 2122 - Additional Guidance Regarding Application of Current Procedures for Testing Energy Consumption of...

Science.gov (United States)

2010-01-14

... Energy Consumption of Refrigerator-Freezers With Automatic Ice Makers AGENCY: Office of the General...) to prescribe standardized test procedures to measure the energy consumption of certain consumer... Energy Consumption of Electric Refrigerators and Electric Refrigerator- Freezers (Appendix A1). DOE...

effects of sulphur addition on addition on and mechanical properties

African Journals Online (AJOL)

User

234-8034714355. 8034714355. 1. EFFECTS OF SULPHUR ADDITION ON. ADDITION ON. 2. AND MECHANICAL PROPERTIES O. 3. 4. C. W. Onyia. 5. 1DEPT. OF METALLURGICAL AND MATERIALS. 6. 2, 4DEPT. OF METALLURGICAL ...

Comparison of the EUCAST and CLSI Broth Microdilution Methods for Testing Isavuconazole, Posaconazole, and Amphotericin B against Molecularly Identified Mucorales Species.

Science.gov (United States)

Chowdhary, Anuradha; Singh, Pradeep Kumar; Kathuria, Shallu; Hagen, Ferry; Meis, Jacques F

2015-12-01

We compared EUCAST and CLSI antifungal susceptibility testing (AFST) methods for triazoles and amphotericin B against 124 clinical Mucorales isolates. The EUCAST method yielded MIC values 1- to 3-fold dilutions higher than those of the CLSI method for amphotericin B. The essential agreements between the two methods for triazoles were high, i.e., 99.1% (voriconazole), 98.3% (isavuconazole), and 87% (posaconazole), whereas it was significantly lower for amphotericin B (66.1%). Strategies for harmonization of the two methods for Mucorales AFST are warranted. Copyright © 2015, American Society for Microbiology. All Rights Reserved.

Misconception on Addition and Subtraction of Fraction at Primary School Students in Fifth-Grade

Science.gov (United States)

Trivena, V.; Ningsih, A. R.; Jupri, A.

2017-09-01

This study aims to investigate the mastery concept of the student in mathematics learning especially in addition and subtraction of fraction at primary school level. By using qualitative research method, the data were collected from 23 grade five students (10-11-year-old). Instruments included a test, that is accompanied by Certainty Response Index (CRI) and interview with students and teacher. The result of the test has been obtained, then processed by analyzing the student’s answers for each item and then grouped by the CRI categories that combined with the results of the interview with students and teacher. The results showed that student’s mastery-concept on additional and subtraction dominated by category ‘misconception’. So, we can say that mastery-concept on addition and subtraction of fraction at fifth-grade students is still low. Finally, the impact can make most of primary student think that learning addition and subtraction of fraction in mathematics is difficult.

Using tank 107-AN caustic addition for confirmation of mixing scale relationship

International Nuclear Information System (INIS)

Chang, S.C.

1995-05-01

A subscale jet mixing program was carried out in two scale tanks to extend the basis of previous subscale tests to include in-tank geometry associated with tank AN-107. The laboratory data will be correlated with the data to be collected in the upcoming tank AN-107 mixing and caustic addition test. The objective is to verify the scaling relationship used in the MWTF mixer design

Mechanical properties of additively manufactured octagonal honeycombs

Energy Technology Data Exchange (ETDEWEB)

Hedayati, R., E-mail: rezahedayati@gmail.com [Department of Mechanical Engineering, Amirkabir University of Technology (Tehran Polytechnic), Hafez Ave, Tehran (Iran, Islamic Republic of); Department of Biomechanical Engineering, Faculty of Mechanical, Maritime, and Materials Engineering, Delft University of Technology (TU Delft), Mekelweg 2, 2628 CD Delft (Netherlands); Sadighi, M.; Mohammadi-Aghdam, M. [Department of Mechanical Engineering, Amirkabir University of Technology (Tehran Polytechnic), Hafez Ave, Tehran (Iran, Islamic Republic of); Zadpoor, A.A. [Department of Biomechanical Engineering, Faculty of Mechanical, Maritime, and Materials Engineering, Delft University of Technology (TU Delft), Mekelweg 2, 2628 CD Delft (Netherlands)

2016-12-01

Honeycomb structures have found numerous applications as structural and biomedical materials due to their favourable properties such as low weight, high stiffness, and porosity. Application of additive manufacturing and 3D printing techniques allows for manufacturing of honeycombs with arbitrary shape and wall thickness, opening the way for optimizing the mechanical and physical properties for specific applications. In this study, the mechanical properties of honeycomb structures with a new geometry, called octagonal honeycomb, were investigated using analytical, numerical, and experimental approaches. An additive manufacturing technique, namely fused deposition modelling, was used to fabricate the honeycomb from polylactic acid (PLA). The honeycombs structures were then mechanically tested under compression and the mechanical properties of the structures were determined. In addition, the Euler-Bernoulli and Timoshenko beam theories were used for deriving analytical relationships for elastic modulus, yield stress, Poisson's ratio, and buckling stress of this new design of honeycomb structures. Finite element models were also created to analyse the mechanical behaviour of the honeycombs computationally. The analytical solutions obtained using Timoshenko beam theory were close to computational results in terms of elastic modulus, Poisson's ratio and yield stress, especially for relative densities smaller than 25%. The analytical solutions based on the Timoshenko analytical solution and the computational results were in good agreement with experimental observations. Finally, the elastic properties of the proposed honeycomb structure were compared to those of other honeycomb structures such as square, triangular, hexagonal, mixed, diamond, and Kagome. The octagonal honeycomb showed yield stress and elastic modulus values very close to those of regular hexagonal honeycombs and lower than the other considered honeycombs. - Highlights: • The octagonal

Bioactive endophytes warrant intensified exploration and conservation.

Science.gov (United States)

Smith, Stephen A; Tank, David C; Boulanger, Lori-Ann; Bascom-Slack, Carol A; Eisenman, Kaury; Kingery, David; Babbs, Beatrice; Fenn, Kathleen; Greene, Joshua S; Hann, Bradley D; Keehner, Jocelyn; Kelley-Swift, Elizabeth G; Kembaiyan, Vivek; Lee, Sun Jin; Li, Puyao; Light, David Y; Lin, Emily H; Ma, Cong; Moore, Emily; Schorn, Michelle A; Vekhter, Daniel; Nunez, Percy V; Strobel, Gary A; Donoghue, Michael J; Strobel, Scott A

2008-08-25

A key argument in favor of conserving biodiversity is that as yet undiscovered biodiversity will yield products of great use to humans. However, the link between undiscovered biodiversity and useful products is largely conjectural. Here we provide direct evidence from bioassays of endophytes isolated from tropical plants and bioinformatic analyses that novel biology will indeed yield novel chemistry of potential value. We isolated and cultured 135 endophytic fungi and bacteria from plants collected in Peru. nrDNAs were compared to samples deposited in GenBank to ascertain the genetic novelty of cultured specimens. Ten endophytes were found to be as much as 15-30% different than any sequence in GenBank. Phylogenetic trees, using the most similar sequences in GenBank, were constructed for each endophyte to measure phylogenetic distance. Assays were also conducted on each cultured endophyte to record bioactivity, of which 65 were found to be bioactive. The novelty of our contribution is that we have combined bioinformatic analyses that document the diversity found in environmental samples with culturing and bioassays. These results highlight the hidden hyperdiversity of endophytic fungi and the urgent need to explore and conserve hidden microbial diversity. This study also showcases how undergraduate students can obtain data of great scientific significance.

Bioactive endophytes warrant intensified exploration and conservation.

Directory of Open Access Journals (Sweden)

Stephen A Smith

2008-08-01

Full Text Available A key argument in favor of conserving biodiversity is that as yet undiscovered biodiversity will yield products of great use to humans. However, the link between undiscovered biodiversity and useful products is largely conjectural. Here we provide direct evidence from bioassays of endophytes isolated from tropical plants and bioinformatic analyses that novel biology will indeed yield novel chemistry of potential value.We isolated and cultured 135 endophytic fungi and bacteria from plants collected in Peru. nrDNAs were compared to samples deposited in GenBank to ascertain the genetic novelty of cultured specimens. Ten endophytes were found to be as much as 15-30% different than any sequence in GenBank. Phylogenetic trees, using the most similar sequences in GenBank, were constructed for each endophyte to measure phylogenetic distance. Assays were also conducted on each cultured endophyte to record bioactivity, of which 65 were found to be bioactive.The novelty of our contribution is that we have combined bioinformatic analyses that document the diversity found in environmental samples with culturing and bioassays. These results highlight the hidden hyperdiversity of endophytic fungi and the urgent need to explore and conserve hidden microbial diversity. This study also showcases how undergraduate students can obtain data of great scientific significance.

The nuclear pacemaker: Is renewed interest warranted

International Nuclear Information System (INIS)

Parsonnet, V.; Berstein, A.D.; Perry, G.Y.

1990-01-01

From 1973 through 1987, 155 radioisotope-powered nuclear pacemakers were implanted in 132 patients at the Newark Beth Israel Medical Center. The longevity of the first 15 devices, all of which were fixed-rate (VOO) pacemakers, was significantly better than that of 15 lithium-chemistry demand (VVI) pacemakers used as control devices (p = 0.0002). Of the entire cohort of 155 nuclear pacemakers, 136 were VVI devices and 19 were VOO units. The patients with VOO pacemakers needed reoperations more often than did those with VVI pacemakers, chiefly for mode change (p less than 0.001). Power-source failure was observed in only 1 case, but 47 nuclear pacemakers were removed for other reasons, including component malfunction (15 units), mode change (12 units), high pacing thresholds (8 units) and lead or connector problems (5 units). The actuarial survival at 15 years was 99% for power sources and 82% for the entire pacing systems (pulse generators plus leads). The frequency of malignancy was similar to that of the population at large and primary tumor sites were randomly distributed. Deaths most commonly were due to cardiac causes (68%). Thus, nuclear pacemakers are safe and reliable and their greater initial cost appears to be offset by their longevity and the resulting decrease in the frequency of reoperations. It is reasonable to suggest that further use be made of long-lasting nuclear power sources for modern pacemakers and other implantable rhythm-management devices

When does atopic dermatitis warrant systemic therapy?

DEFF Research Database (Denmark)

Simpson, Eric L; Bruin-Weller, Marjolein; Flohr, Carsten

2017-01-01

therapy in AD and provide a framework for evaluation before making this therapeutic decision with the patient. METHODS: A subgroup of the International Eczema Council determined aspects to consider before prescribing systemic therapy. Topics were assigned to expert reviewers who performed a topic...... systemic therapy include considering alternate or concomitant diagnoses, avoiding trigger factors, optimizing topical therapy, ensuring adequate patient/caregiver education, treating coexistent infection, assessing the impact on quality of life, and considering phototherapy. LIMITATIONS: Our work...

Greenhouse gas reductions; not warranted, not beneficial

International Nuclear Information System (INIS)

Green, K.

2003-01-01

This report deals with climate change and greenhouse gas emissions, especially regional climate change predictions, from a sceptic's point of view. It rejects all the conventional evidence supporting claims of extreme man-made climate changes, dismissing them as alarmist and inherently uncertain. Similarly, it characterizes policy prescriptions based on this evidence as faulty and as measures which, if implemented, would do both current and future generations considerably more harm than good. Calls for energy efficiency and conservation, reliance on renewable energy sources, improved efficiency of conventional vehicles, hybrid and fuel-cell-driven cars, reducing the amount of driving, establishing greenhouse gas registries, are all dismissed as impractical, imposing higher costs on energy generally, slowing economic growth in the process, and scaring people to adopt unwise public policies by exaggerating the certainty of predictions about man-made climate change. While dismissing the arguments advanced by 'old-school' environmentalists, the report does not question the validity of the overall theory or details of the core greenhouse effect, its main targets are the anthropogenic components of the observed temperature record, and the evidence of a clear cause-and-effect link between anthropogenic forcing and changes in the Earth's surface temperature. Overall, the report dismisses the 'conventional' view of the extent of climate change, the cause of that change and the risk it poses. It emphasizes the limitations on economic freedom that proposed policies would inflict, and argues in favour of more studies to provide the foundation for a societal response based on a solid understanding of the science behind climate change, and the impact of proposed policy options. 32 refs., 2 figs

Measuring Distribution Performance? Benchmarking Warrants Your Attention

Energy Technology Data Exchange (ETDEWEB)

Ericson, Sean J [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Alvarez, Paul [The Wired Group

2018-04-13

Identifying, designing, and measuring performance metrics is critical to securing customer value, but can be a difficult task. This article examines the use of benchmarks based on publicly available performance data to set challenging, yet fair, metrics and targets.

When does atopic dermatitis warrant systemic therapy?

DEFF Research Database (Denmark)

Simpson, Eric L; Bruin-Weller, Marjolein; Flohr, Carsten

2017-01-01

-specific literature review, referred to guidelines when available, and provided interpretation and expert opinion. RESULTS: We recommend a systematic and holistic approach to assess patients with severe signs and symptoms of AD and impact on quality of life before systemic therapy. Steps taken before commencing......BACKGROUND: Although most patients with atopic dermatitis (AD) are effectively managed with topical medication, a significant minority require systemic therapy. Guidelines for decision making about advancement to systemic therapy are lacking. OBJECTIVE: To guide those considering use of systemic...... therapy in AD and provide a framework for evaluation before making this therapeutic decision with the patient. METHODS: A subgroup of the International Eczema Council determined aspects to consider before prescribing systemic therapy. Topics were assigned to expert reviewers who performed a topic...

Solid sand particle addition can enhance the production of resting cysts in dinoflagellates

Science.gov (United States)

Yang, Aoao; Hu, Zhangxi; Tang, Yingzhong

2018-03-01

Resting cysts are an important part of the life cycle for many harmful algal bloom-forming dinoflagellates, and play vital roles in the recurrence and geographical spread of harmful algal blooms. Numerous factors have been suggested to regulate the formation of resting cysts, although only a few have been proven to be significant. Cyst formation can be induced by adverse environmental conditions such as drastic changes in temperature, light, salinity, and nutrient levels, and by biological interactions. In this study, we evaluated the ability of an artificial factor (fine sand particles) to enhance the formation of resting cysts. Fine sand particles were added to cultures of dinoflagellates that are known to produce cysts. The addition of fine sand particles significantly increased both the production rate and final yield of cysts in cultures of Scrippsiella trochoidea, Biecheleria brevisulcata, and Levanderina fissa (= Gymnodinium fissum, Gyrodinium instriatum, Gyrodinium uncatenum). The largest increase in the final yield (107-fold) of cysts as a result of sand addition was in S. trochoidea. However, addition of fine sand particles did not induce cyst formation, or barely affected cyst formation, in Akashiwo sanguinea, Cochlodinium polykrikoides and Pheopolykrikos hartmannii, which are also known to be cyst-producing species. We speculated that addition of sand significantly increased the chances of cell collision, which triggered cyst formation. However, further research is required to test this idea. Importantly, our findings indicate that the addition of fine sand particles is a useful method to obtain a large quantity of cysts in a short time for laboratory studies or tests; for example, if a cyst viability test is being used to assess the effectiveness of ships' ballast water treatment.

Mechanical Properties of a Newly Additive Manufactured Implant Material Based on Ti-42Nb.

Science.gov (United States)

Schulze, Christian; Weinmann, Markus; Schweigel, Christoph; Keßler, Olaf; Bader, Rainer

2018-01-13

The application of Ti-6Al-4V alloy or commercially pure titanium for additive manufacturing enables the fabrication of complex structural implants and patient-specific implant geometries. However, the difference in Young's modulus of α + β-phase Ti alloys compared to the human bone promotes stress-shielding effects in the implant-bone interphase. The aim of the present study is the mechanical characterization of a new pre-alloyed β-phase Ti-42Nb alloy for application in additive manufacturing. The present investigation focuses on the mechanical properties of SLM-printed Ti-42Nb alloy in tensile and compression tests. In addition, the raw Ti-42Nb powder, the microstructure of the specimens prior to and after compression tests, as well as the fracture occurring in tensile tests are characterized by means of the SEM/EDX analysis. The Ti-42Nb raw powder exhibits a dendrite-like Ti-structure, which is melted layer-by-layer into a microstructure with a very homogeneous distribution of Nb and Ti during the SLM process. Tensile tests display Young's modulus of 60.51 ± 3.92 GPa and an ultimate tensile strength of 683.17 ± 16.67 MPa, whereas, under a compressive load, a compressive strength of 1330.74 ± 53.45 MPa is observed. The combination of high mechanical strength and low elastic modulus makes Ti-42Nb an interesting material for orthopedic and dental implants. The spherical shape of the pre-alloyed material additionally allows for application in metal 3D printing, enabling the fabrication of patient-specific structural implants.

Additive Manufacturing for Highly Efficient Window Inserts CRADA Report

Energy Technology Data Exchange (ETDEWEB)

Roschli, Alex C. [ORNL; Chesser, Phillip C. [ORNL; Love, Lonnie J. [ORNL

2018-04-01

ORNL partnered with the Mackinac Technology Company to demonstrate how additive manufacturing can be used to create highly energy efficient window inserts for retrofit in pre-existing buildings. Many early iterations of the window inserts were fabricated using carbon fiber reinforced thermoplastics and polycarbonate films as a stand in for the low-e coated films produced by the Mackinac Technology Company. After demonstration of the proof of concept, i.e. custom window inserts with tensioned film, the materials used for the manufacture of the frames was more closely examined. Hollow particle-filled syntactic foam and low-density polymer composites formed by expandable microspheres were explored as the materials used to additively manufacture the frames of the inserts. It was concluded that low-cost retrofit window inserts in custom sizes could be easily fabricated using large scale additive manufacturing. Furthermore, the syntactic and expanded foams developed and tested satisfy the mechanical performance requirements for the application.

Influence of tribological additives on friction and impact performance of injection moulded polyacetal

DEFF Research Database (Denmark)

Laursen, Jens Lolle; Sivebæk, Ion Marius; Christoffersen, L.W.

2009-01-01

Tribological additives are used to improve frictional properties of injection moulded thermoplastics. The additives might however also affect the mechanical properties of the material. The influence of processing conditions on both frictional and mechanical properties is highly relevant in the de......Tribological additives are used to improve frictional properties of injection moulded thermoplastics. The additives might however also affect the mechanical properties of the material. The influence of processing conditions on both frictional and mechanical properties is highly relevant...... in the development of tribologically modified grades. In the present study we investigate how two commonly used tribological additives, polydimethylsiloxane and polytetrafluoroethylene, affect friction and impact properties of polyacetal (polyoxymethylene). A new injection mould provides test specimens for both...

Performance Test on Compression Ignition Engine by Blending Ethanol and Waste Plastic Pyrolysis Oil with Cetane Additive

Science.gov (United States)

Padmanabhan, S.; Ganesan, S.; Jeswin Arputhabalan, J.; Chithrala, Varun; Ganesh Bairavan, P.

2017-05-01

The demand for diesel fuel is higher than that of petrol throughout the world hence seeking alternative to mineral diesel is a natural choice. Alternative fuels should be easily available at lower cost, environment friendly and fulfill energy needs without modifying engine’s operational parameters. Waste to energy is the trend in the selection of alternate fuels. In this work, Waste Plastic Pyrolysis oil (WPPO), Ethanol, Diesel blend with Cetane additive has been attempted as an alternative fuel. A Twin cylinder, Direct Injection engine was used to assess the engine performance and emission characteristics of waste plastic pyrolysis oil with cetane additive. Experimental results of blended plastic fuel and diesel fuel were compared.

Evaluation of practicability of aluminosilicate additive fuel. Influence of aluminosilicate for reprocessing and corrosion of pellet

International Nuclear Information System (INIS)

Matsunaga, Junji; Kashibe, Shinji; Kinoshita, Mika; Ishimoto, Shinji; Harada, Kenichi

2014-01-01

Al-Si-O additive fuel is a modified pellet to improve the pellet-cladding interaction (PCI) resistance. This practicability assessment concerns the effect of Al-Si-O addition on the reprocessing and steam corrosion behavior. To address these concerns, a fuel dissolution test in nitric acid and a pellet corrosion test in humidified gas were carried out using the irradiated Al-Si-O additive fuel. Regardless of the Al-Si-O concentration, the dissolution rates of all Al-Si-O additive fuels were faster than that of the standard fuel. The morphology of the insoluble residue obtained from the irradiated Al-Si-O additive fuel could be considered as acceptable for retrieval by the clarification process using a conventional precipitation model. The corrosion resistance of the irradiated Al-Si-O additive fuel to high-temperature (at 1273 K) humidified gas was comparable to or better than that of the standard fuel. The result was interpreted as being due to a large grain size effect by Al-Si-O addition. (author)

Mechanical Properties of Austenitic Stainless Steel Made by Additive Manufacturing.

Science.gov (United States)

Luecke, William E; Slotwinski, John A

2014-01-01

Using uniaxial tensile and hardness testing, we evaluated the variability and anisotropy of the mechanical properties of an austenitic stainless steel, UNS S17400, manufactured by an additive process, selective laser melting. Like wrought materials, the mechanical properties depend on the orientation introduced by the processing. The recommended stress-relief heat treatment increases the tensile strength, reduces the yield strength, and decreases the extent of the discontinuous yielding. The mechanical properties, assessed by hardness, are very uniform across the build plate, but the stress-relief heat treatment introduced a small non-uniformity that had no correlation to position on the build plate. Analysis of the mechanical property behavior resulted in four conclusions. (1) The within-build and build-to-build tensile properties of the UNS S17400 stainless steel are less repeatable than mature engineering structural alloys, but similar to other structural alloys made by additive manufacturing. (2) The anisotropy of the mechanical properties of the UNS S17400 material of this study is larger than that of mature structural alloys, but is similar to other structural alloys made by additive manufacturing. (3) The tensile mechanical properties of the UNS S17400 material fabricated by selective laser melting are very different from those of wrought, heat-treated 17-4PH stainless steel. (4) The large discontinuous yielding strain in all tests resulted from the formation and propagation of Lüders bands.

Survey of solar thermal test facilities

Energy Technology Data Exchange (ETDEWEB)

Masterson, K.

1979-08-01

The facilities that are presently available for testing solar thermal energy collection and conversion systems are briefly described. Facilities that are known to meet ASHRAE standard 93-77 for testing flat-plate collectors are listed. The DOE programs and test needs for distributed concentrating collectors are identified. Existing and planned facilities that meet these needs are described and continued support for most of them is recommended. The needs and facilities that are suitable for testing components of central receiver systems, several of which are located overseas, are identified. The central contact point for obtaining additional details and test procedures for these facilities is the Solar Thermal Test Facilities Users' Association in Albuquerque, N.M. The appendices contain data sheets and tables which give additional details on the technical capabilities of each facility. Also included is the 1975 Aerospace Corporation report on test facilities that is frequently referenced in the present work.

Theory of nonparametric tests

CERN Document Server

Dickhaus, Thorsten

2018-01-01

This textbook provides a self-contained presentation of the main concepts and methods of nonparametric statistical testing, with a particular focus on the theoretical foundations of goodness-of-fit tests, rank tests, resampling tests, and projection tests. The substitution principle is employed as a unified approach to the nonparametric test problems discussed. In addition to mathematical theory, it also includes numerous examples and computer implementations. The book is intended for advanced undergraduate, graduate, and postdoc students as well as young researchers. Readers should be familiar with the basic concepts of mathematical statistics typically covered in introductory statistics courses.

Technological foundations of processing tomato pomace in feed additives

Directory of Open Access Journals (Sweden)

B. Yegorov

2015-05-01

Full Text Available Introduction. Search for new types of alternative raw material for the efficient development of poultry industry and problem of waste disposal of canning industry made it necessary to develop a method of processing tomato pomace in feed additives. Materials and methods. Sampling, preparation and testing were carried out by general and specific organ oleptic and physical-technological methods of assessment and analysis of the properties of raw materials and finished products. Results. Incorporation of tomato pomace in the feed additive reduces the cost of raw materials and expenses associated with moistening of the mixture before extrusion and incorporation of chalk feed will solve the problem of calcium imbalance of laying hens. It was found that extrusion process has improved the physical properties of feed additive and showed the possibility of its use as a feed component: moisture content decreased by 34.5 %, the angle of repose increased by 11.4 %, flowability decreased by 39.7 % and bulk density decreased by 32.3 %. Conclusions. The resulting feed additive will solve the problem of diversification of raw materials, waste, calcium imbalance of laying hens and reduce expenses on compound animal feedstuff production.

Migration of fluorochemical paper additives from food-contact paper into foods and food simulants.

Science.gov (United States)

Begley, T H; Hsu, W; Noonan, G; Diachenko, G

2008-03-01

Fluorochemical-treated paper was tested to determine the amount of migration that occurs into foods and food-simulating liquids and the characteristics of the migration. Migration characteristics of fluorochemicals from paper were examined in Miglyol, butter, water, vinegar, water-ethanol solutions, emulsions and pure oil containing small amounts of emulsifiers. Additionally, microwave popcorn and chocolate spread were used to investigate migration. Results indicate that fluorochemicals paper additives do migrate to food during actual package use. For example, we found that microwave popcorn contained 3.2 fluorochemical mg kg(-1) popcorn after popping and butter contained 0.1 mg kg(-1) after 40 days at 4 degrees C. Tests also indicate that common food-simulating liquids for migration testing and package material evaluation might not provide an accurate indication of the amount of fluorochemical that actually migrates to food. Tests show that oil containing small amounts of an emulsifier can significantly enhance migration of a fluorochemical from paper.

E-ELT M1 test facility

Science.gov (United States)

Dimmler, M.; Marrero, J.; Leveque, S.; Barriga, P.; Sedghi, B.; Mueller, M.

2012-09-01

During the advanced design phase of the European Extremely Large Telescope (E-ELT) several critical components have been prototyped. During the last year some of them have been tested in dedicated test stands. In particular, a representative section of the E-ELT primary mirror has been assembled with 2 active and 2 passive segments. This test stand is equipped with complete prototype segment subunits, i.e. including support mechanisms, glass segments, edge sensors, position actuators as well as additional metrology for monitoring. The purpose is to test various procedures such as calibration, alignment and handling and to study control strategies. In addition the achievable component and subsystem performances are evaluated, and interface issues are identified. In this paper an overview of the activities related to the E-ELT M1 Test Facility will be given. Experiences and test results are presented.

Enhanced shear strength of sodium bentonite using frictional additives

International Nuclear Information System (INIS)

Schmitt, K.E.; Bowders, J.J.; Gilbert, R.B.; Daniel, D.E.

1997-01-01

One of the most important obstacles to using geosynthetic clay liners (GCLs) in landfill cover systems is the low shear strength provided by the bentonitic portion of the GCL. In this study, the authors propose that granular, frictional materials might be added to the bentonite to form an admixture that would have greater shear strength than the bentonite alone while still raining low hydraulic conductivity. Bentonite was mixed with two separate granular additives, expanded shale and recycled to form mixtures consisting of 20-70% bentonite by weight. In direct shear tests at normal stresses of 34.5-103.5 kPa, effective friction angles were measured as 45 degrees for the expanded 36 degrees for the recycled glass, and 7 degrees for the hydrated granular bentonite. The strength of the expanded shale mixtures increased nearly linearly as the percentage shale in the mixture increased, to 44 degrees for a bentonite mixture with 80% shale. The addition of recycled glass showed little effect on the shear strength of the mixtures of glass and bentonite. Hydraulic conductivity measurements for both types of mixtures indicated a linear increase with log(k) as the amount of granular additive increased. For applications involving geosynthetic clay liners for cover systems, a mixture of 40% expanded shale and 60% bentonite is recommended, although further testing must be done. The 40/60 mixture satisfies the hydraulic equivalency requirement, with k = 5.1X10 -9 cm/sec, while increasing the shear strength parameters of the bentonitic mixture to φ' = 17 degrees and c' = 0

On the dynamic response of additively manufactured 316L

Science.gov (United States)

Smith, Liam; Eakins, Daniel; Chapman, David; Hooper, Paul

2017-06-01

Understanding the dynamic performance of Additively Manufactured (AM) materials is important when designing components for real-world applications. A series of Taylor tests were carried out on AM and conventionally manufactured 316L Stainless Steel. AM specimens were produced with a Renishaw AM250 selective laser melting machine. Taylor tests were conducted in a reverse anvil-on-rod configuration with soft capture and post loading measurements used to corroborate high speed deformation imaging. The influence of microstructure orientation and surface roughness was investigated by manufacturing samples parallel and perpendicular to build direction and with both as-built and machined finishes. Results were compared with optimised Johnson-Cook and Zerilli-Armstrong constitutive models within AUTODYN FE software.

77 FR 3408 - Annual Stress Test

Science.gov (United States)

2012-01-24

...-2011-0029] RIN 1557-AD58 Annual Stress Test AGENCY: Office of the Comptroller of the Currency (``OCC... certain companies to conduct annual stress tests pursuant to regulations prescribed by their respective... stress test as prescribed by this proposed rule. In addition to the annual stress test requirement, such...

Evaluation of intravenous fluorescein in intradermal allergy testing in psittacines.

Science.gov (United States)

Nett, Claudia S; Hosgood, Giselle; Heatley, J Jill; Foil, Carol S; Tully, Thomas N

2003-12-01

This study was designed to improve the clinical feasibility of intradermal skin testing of psittacine birds using intravenous fluorescein stain. Twenty-five healthy, anaesthetized Hispaniolan Amazon parrots (Amazona ventralis) were injected intravenously with 10 mg kg-1 fluorescein-sodium 1% followed by intradermal injections of 0.02 mL phosphate-buffered saline, histamine phosphate (1:100,000 w/v) and codeine phosphate (1:100,000 w/v) at the sternal apteria. Wheal diameters of reaction sites were measured grossly and under illumination with a Wood's lamp after 5 and 10 min. Fluorescence-enhanced injection sites were scored between 0 and 2, with 0 equivalent to normal skin and 2 equivalent to a plucked feather follicle. The presence of a fluorescent halo around intradermal injections was also recorded. Under Wood's light illumination at 10 min, histamine and saline were evaluated as positive and negative controls, respectively, based on a positive test having a halo and a score of 2. Sensitivity and specificity were each 76% for halo, 84 and 42% for score and 64 and 77% for combination of score and halo, respectively. Further, mean histamine reactions were significantly larger than codeine phosphate and saline (8.8 +/- 0.4 mm; 7.2 +/- 0.3 mm; 5.9 +/- 0.6 mm); however, this finding was not consistent in individual birds. Wheal size, halo presence and score were affected by site location independent from the injected compound. Intravenous fluorescein improved the readability of avian skin tests; however, the compounds tested raised inconsistent reactions in wheal size, score or halo presence. The compound-independent site effect raises concern on the validity of avian skin testing and warrants investigation of other techniques such as in vitro allergy testing. Based on our findings, intradermal allergy testing in psittacines with or without fluorescein is unreliable and cannot be recommended for practical clinical use.

Internal Fiber Structure of a High-Performing, Additively Manufactured Injection Molding Insert

DEFF Research Database (Denmark)

Hofstätter, Thomas; Baier, Sina; Trinderup, Camilla H.

A standard mold is equipped with additively manufactured inserts in a rectangular shape produced with vat photo polymerization. While the lifetime compared to conventional materials such as brass, steel, and aluminum is reduced, the prototyping and design phase can be shortened significantly...... by using flexible and cost-effective additive manufacturing technologies. Higher production volumes still exceed the capability of additively manufactured inserts, which are overruled by the stronger performance of less-flexible but mechanically advanced materials. In this contribution, the internal...... structure of a high-performing, fiber-reinforced injection molding insert has been analyzed. The insert reached a statistically proven and reproducible lifetime of 4,500 shots, which significantly outperforms any other previously published additively manufactured inserts. Computer tomography, tensile tests...

Effects of Ce, La and Ba addition on the electrochemical behavior of super duplex stainless steels

International Nuclear Information System (INIS)

Yoo, Yun-Ha; Choi, Yoon-Seok; Kim, Jung-Gu; Park, Yong-Soo

2010-01-01

The effects of rare earth metal (REM: Ce, La) and Ba addition on aqueous corrosion properties of super duplex stainless steels (SDSS) were investigated by electrochemical tests and surface analyses. The results of potentiodynamic test indicated that the passive range increased by the addition of Ce, La, and Ba, indicating increased relative resistance to localized corrosion. The EIS measurements showed that the Ce-La-Ba-bearing alloys exhibited higher R ct and R p values than the Ce-La-Ba-free alloy at the passive and breakdown states. Furthermore, the additions of REMs and Ba together promoted the formation of dense chromium-enriched passive film.

Quaternion normalization in additive EKF for spacecraft attitude determination

Science.gov (United States)

Bar-Itzhack, I. Y.; Deutschmann, J.; Markley, F. L.

1991-01-01

This work introduces, examines, and compares several quaternion normalization algorithms, which are shown to be an effective stage in the application of the additive extended Kalman filter (EKF) to spacecraft attitude determination, which is based on vector measurements. Two new normalization schemes are introduced. They are compared with one another and with the known brute force normalization scheme, and their efficiency is examined. Simulated satellite data are used to demonstrate the performance of all three schemes. A fourth scheme is suggested for future research. Although the schemes were tested for spacecraft attitude determination, the conclusions are general and hold for attitude determination of any three dimensional body when based on vector measurements, and use an additive EKF for estimation, and the quaternion for specifying the attitude.

Tribological study on rapeseed oil with nano-additives in close contact sliding situation

Science.gov (United States)

Gupta, Rajeev Nayan; Harsha, A. P.; Singh, Sagar

2018-02-01

The present work deals with the tribological evaluation of three types of nano-additives, i.e., copper oxide (CuO; ≈ 151.2 nm), cerium oxide (CeO2; ≈ 80 nm) and polytetrafluoroethylene (PTFE; ≈ 90.4 nm) with rapeseed oil under steel-steel sliding contacts. The nano-additives concentrations in the base oil were 0.1, 0.25 and 0.5% w/v for the lubricant formulation. Further, the rapeseed oil was also epoxidized by a chemical method and the tribological behavior was compared with the base oil (unmodified oil) at similar nano-additives concentrations. The ASTM standards were followed for the study of wear preventive and extreme-pressure analysis of nanolubricants, and it was carried out using four-ball tester. In the antiwear test, CeO2 and PTFE nano-additives have shown the significant reduction in the wear scar diameter at the concentration of 0.1% w/v. In the extreme-pressure test, 0.5% w/v concentration was optimum for oxide nanoparticles; however, PTFE nanoparticles did not show positive effect with both the base oils. Different characterization techniques were employed to confirm the oil modification and for the study of the worn surfaces.

Effect of additional holes on transient thermal fatigue life of gas turbine casing

Directory of Open Access Journals (Sweden)

H. Bazvandi

2017-10-01

Full Text Available Gas turbines casings are susceptible to cracking at the edge of eccentric pin hole, which is the most likely position for crack initiation and propagation. This paper describes the improvement of transient thermal fatigue crack propagation life of gas turbines casings through the application of additional holes. The crack position and direction was determined using non-destructive tests. A series of finite element patterns were developed and tested in ASTM-A395 elastic perfectly-plastic ductile cast iron. The effect of arrangement of additional holes on transient thermal fatigue behavior of gas turbines casings containing hole edge cracks was investigated. ABAQUS finite element package and Zencrack fracture mechanics code were used for modeling. The effect of the reduction of transient thermal stress distribution around the eccentric pin hole on the transient thermal fatigue crack propagation life of the gas turbines casings was discussed. The result shows that transient thermal fatigue crack propagation life could be extended by applying additional holes of larger diameter and decreased by increasing the vertical distance, angle, and distance between the eccentric pin hole and the additional holes. The results from the numerical predictions were compared with experimental data.

Improving complex kinship analyses with additional STR loci.

Science.gov (United States)

Carboni, Ilaria; Iozzi, Sara; Nutini, Anna Lucia; Torricelli, Francesca; Ricci, Ugo

2014-11-01

In a standard paternity testing, mother, child, and alleged father are analyzed with STR markers using commercially available kits. Since Italian civil legislation does not have thresholds to confirm a paternity, paternity is practically proven when likelihood ratio increases prior probability of paternity to posterior, accepted by court as sufficient. However, in some cases the number of markers included in a commercial kit may be insufficient to conclusively prove or disprove a relationship between individuals, especially when complex family scenarios are suspected or indirect analyses are required. Additional genetic information can increase the values of the likelihood ratio regarding the detection of true parental relationships in a pedigree, while reducing the chances of false attributions (e.g. false paternities). In these cases the introduction of a 26Plex amplification system allows to examine 23-26 additional markers depending on the commercial kit used, thus increasing the statistical power of the kinship analysis. The PCR conditions were optimized for a multiplex amplification system and a new generation CE instrument. In order to demonstrate the utility of additional STRs markers, four complex kinship cases are presented. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Analysis of clonogenic human brain tumour cells: preliminary results of tumour sensitivity testing with BCNU

Energy Technology Data Exchange (ETDEWEB)

Rosenblum, M L; Dougherty, D A; Deen, D F; Hoshino, T; Wilson, C B [California Univ., San Francisco (USA). Dept. of Neurology

1980-04-01

Biopsies from 6 patients with glioblastoma multiforme were disaggregated and single cells were treated in vitro with various concentrations of 1,3-bis(2-chloroethyl)-1-nitroso urea (BCNU) and plated for cell survival. One patient's cells were sensitive to BCNU in vitro; after a single dose of BCNU her brain scan reverted to normal and she was clinically well. Five tumours demonstrated resistance in vitro. Three of these tumours progressed during the first course of chemotherapy with a nitrosourea and the patients died at 21/2, 4 and 81/2 months after operation. Two patients who showed dramatic responses to radiation therapy were considered unchanged after the first course of nitrosourea therapy (although one demonstrated tumour enlargement on brain scan). The correlation of in vitro testing of tumour cell sensitivity with actual patient response is encouraging enough to warrant further work to determine whether such tests should weigh in decisions on patient therapy.

Eberline Alpha 7L Test Report

CERN Document Server

Chiaro, P J

2002-01-01

An Eberline continuous alpha air monitor model Alpha 7L was evaluated at Oak Ridge National Laboratory (ORNL) using the capabilities available at the Environmental Effects Laboratory (EELab). A series of tests were performed to ensure that procured units meet the requirements of the purchasing facility, Los Alamos National Laboratory (LANL). In addition to reporting on the results of each test, other activities were performed to reduce discovered susceptibilities. The parameters monitored during the tests typically included the airflow rate and/or net sup 2 sup 3 sup 9 Pu concentration values (pCi/liter). In addition, the spectrum display and operational status were monitored. Follow up tests were also performed on two LANL-provided production units. The results of those tests are at the end of this report.

Influence of the Reclaim Addition on Properties of Moulding Sands with the Geopol Binder

Directory of Open Access Journals (Sweden)

Drożyński D.

2015-03-01

Full Text Available The investigation results of the influence of the reclaim additions on the properties of moulding sands with the GEOPOL geopolymer binder developed by the SAND TEAM Company were presented. Two brands of hardeners were applied in the tested compositions, the first one was developed by the SAND TEAM Company, marked SA72 and the new hardener offered by the KRATOS Company, marked KR72. The main purpose of investigations was to determine the influence of reclaim fractions and the applied hardener on the basic moulding sands properties, such as: bending and tensile strength, permeability and grindability. The unfavourable influence of the reclaim additions into moulding sands on the tested properties as well as an increased hardening rate, were found. Moulding sands, in which the hardener KR72 of the KRATOS Company was used, were less sensitive to the reclaim additions

Effect of Cu addition on microstructure and corrosion behavior of spray-deposited Zn–30Al alloy

International Nuclear Information System (INIS)

Wang Feng; Xiong Baiqing; Zhang Yongan; Liu Hongwei; Li Zhihui; Li Xiwu; Qu Chu

2012-01-01

Highlights: ► Zn–30Al–xCu alloys were synthesized by the spray atomization and deposition technique. ► Immersion test and electrochemical measurements have been used to estimate the corrosion rate and the behavior. ► The result indicates that the 1 wt.% Cu addition displays superior corrosion resistance. - Abstract: In this study, one binary Zn–30Al and three ternary Zn–30Al–Cu alloys were synthesized by the spray atomization and deposition technique. The microstructures of the spray-deposited alloys were investigated by means of scanning electron microscope (SEM), transmission electron microscope (TEM), X-ray diffraction (XRD). Immersion test, potentiodynamic polarization and electrochemical impedance measurements have been used to estimate the corrosion rate and the behavior. The results indicate that the 1 wt.% Cu addition to spray-deposited Zn–30Al alloy does not make significant change in microstructure. However, with the 2, 4 wt.% Cu additions to the alloy, some ε-CuZn 4 compounds with particle or irregular shapes were observed on the grain boundaries in the microstructures. Immersion test and electrochemical measurements confirmed that the 1 wt.% Cu addition displays superior corrosion resistance, whereas the 2, 4 wt.% Cu additions have a baneful effect on the corrosion behavior.

Addition of photosensitive dopants to the D0 liquid argon calorimeter

International Nuclear Information System (INIS)

Amos, N.A.; Anderson, D.F.

1992-10-01

The addition of photosensitive dopants to liquid argon greatly enhances the signal from heavily ionizing particles. Since binding energy losses we correlated with the heavily ionizing component in hadronic showers, the addition of photosensitive dopants has been suggested as a mechanism to tune the e/π ratio in liquid argon calorimeters. A measurement was performed at the FNAL test beam, adding 4 ppM tetramethylgermanium to the Dφ uranium-liquid argon calorimeter. An increase in response for electromagnetic and hadronic showers was observed, with no net change in the e/π ratio

Integrated leak rate test of the FFTF [Fast Flux Test Facility] containment vessel

International Nuclear Information System (INIS)

Grygiel, M.L.; Davis, R.H.; Polzin, D.L.; Yule, W.D.

1987-04-01

The third integrated leak rate test (ILRT) performed at the Fast Flux Test Facility (FFTF) demonstrated that effective leak rate measurements could be obtained at a pressure of 2 psig. In addition, innovative data reduction methods demonstrated the ability to accurately account for diurnal variations in containment pressure and temperature. Further development of methods used in this test indicate significant savings in the time and effort required to perform an ILRT on Liquid Metal Reactor Systems with consequent reduction in test costs

Improvement of engineering soil properties using non -traditional additives

Directory of Open Access Journals (Sweden)

Waheed Mohanned

2018-01-01

Full Text Available Laboratory experiments are conducted to evaluate the effect of some non-traditional additives on the engineering properties of clayey soil, which show problematic phenomenon when used as a construction material. The conducted tests covered the influence of these additives on various parameters like consistency limits, compaction characteristics and CBR value. Two nontraditional stabilizers are selected in this study, polymers and phosphoric acid at three different percent which are (1%, 3% and 5% of the dry soil weight. It is concluded that addition of the polymer to the clayey soil results in a slight increase in plastic limit while the liquid limit is not affected accompanied by a marginal decrease in the dry unit weight while the optimum moisture content remains unaffected. The addition of phosphoric acid to the clayey soil has no effect on its Atterberg limits. In general, it is observed that polymer is found to be ineffective as a stabilizer to improve clayey soils, especially in small amounts of about (3%. The phosphoric acid treated soil gained better improvement for all amounts of additive used. For (3% acid treated soil the CBR is about (360% compared to that of untreated soil, for that, it can be concluded that the improvement using phosphoric acid in the clay soils is a promising option and can be applied to solve the geotechnical stabilization problems.

Prototyping of Individual Ankle Orthosis Using Additive Manufacturing Technologies

Directory of Open Access Journals (Sweden)

Natalia Wierzbicka

2017-09-01

Full Text Available The paper presents design and manufacturing process of an individualized ankle orthosis using additive manufacturing technologies and reverse engineering. Conventional processes of manufacturing of orthosesareexpensive and time consuming -an alternative method was proposed. The patient’s leg was 3D scanned and the orthosis was designed using a CAD system. It was then manufactured using the Fused Deposition Modelling technology, assembled and fully tested. Positive results were obtained.

Hypersensitivity to tartrazine (FD&C Yellow No. 5) and other dyes and additives present in foods and pharmaceutical products.

Science.gov (United States)

Lockey, S D

1977-03-01

Tartrazine (FD&C Yellow No. 5) and other allowed certified color additives may have an exacerbating effect in chronic urticaria and asthma sufferers. In the individual patient the only way to determine their relevance is to administer test doses. By altering doses, timing and substances and by interspacing controls a battery of tests has been developed. Methods of testing for sensitization to food additives and analgesics are described.

Development of coatings for ultrasonic additive manufacturing sonotrode using laser direct metal deposition process

Energy Technology Data Exchange (ETDEWEB)

Niyanth S, Niyanth [ORNL; Dehoff, Ryan R [ORNL; Jordan, Brian H [ORNL; Babu, Sudarsanam Suresh [ORNL

2016-10-01

ORNL partnered with Fabrisonic, LLC to develop galling resistant hard facing coatings on sonotrodes used to fabricate 3D printed materials using ultrasonic additive manufacturing. The development and deployment of a coated sonotrode is expected to push the existing state of the art to facilitate the solidstate additive manufacturing of hard steels and titanium alloys. To this effect a structurally amorphous stainless steel material and cobalt chrome material were deposited on the sonotrode material. Both the deposits showed good adhesion to the substrate. The coatings made using the structurally amorphous steel materials showed cracking during the initial trials and cracking was eliminated by deposition on a preheated substrate. Both the coatings show hardness in excess of 600 HVN. Thus the phase 1 of this project has been used to identify suitable materials to use to coat the sonotrode. Despite the fact that successful deposits were obtained, the coatings need to be evaluated by performing detailed galling tests at various temperatures. In addition field tests are also necessary to test the stability of these coatings in a high cycle ultrasonic vibration mode. If awarded, phase 2 of the project would be used to optimize the composition of the deposit material to maximize galling resistance. The industrial partner would then use the coated sonotrode to fabricate builds made of austenitic stainless steel to test the viability of using a coated sonotrode.

Simple additive manufacturing of an osteoconductive ceramic using suspension melt extrusion

DEFF Research Database (Denmark)

Slots, Casper; Bonde Jensen, Martin; Ditzel, Nicholas

2017-01-01

/calcium phosphate suspension melt for simple additive manufacturing of ceramic tricalcium phosphate implants. METHODS: A wide variety of non-aqueous liquids were tested to determine the formulation of a storable 3D printable tricalcium phosphate suspension ink, and only fatty acid-based inks were found to work...

Formalin treatments pass new tests. Additional notes on the control of ecto-parasitic protozoa

Science.gov (United States)

1940-01-01

After the completion of the eхреriments reported recently, in which the efficacy of formalin in controlling infections of Gostia mecatrix was demonstrated, the author was afforded an opportunity to test the value of formalin solutions in combatting established mixed infections of (Gyrodactylus, Tricbodina, Cyclochaeta) and a stalked protozoan on rainbow trout fingerlings. This opportunity was provided through the courtesy and cooperation of Clarence F. Pautzke, Chief Biologist for the Washington State Game Department, and Lee Walters, Superintendent of the Washington State Hatchery at Seward Park, Seattle.

Effect of porcelain polishing addition of waste in properties blocks ceramic

International Nuclear Information System (INIS)

Santana, G.L.; Barbosa Neto, M.C.; Campos, L.F.; Macedo, D.A; Dutra, R.P.S.

2016-01-01

This work has as objective the study of the technological properties of ceramic blocks with addition of residue porcelain polishing. The test samples are produced with clay base, where the waste is introduced in concentrations of 10% and 20% by mass, to evaluate its influence on the properties of the ceramic block. All these materials were characterized by determining their chemical composition (XRF) and X-ray diffraction Sintering was performed at temperatures of 850 ° C, 950 ° C and 1100 ° C with a heating rate of 2 ° C / me and 60 minutes of landing. After this, there was obtained the technological properties of the samples such as: Loss on fire, the burning linear shrinkage, water absorption, porosity and density, as well as, mechanical strength properties through the flexural strength test. The results show that the addition of waste influenced both the technological properties, the mechanical properties evaluated in this study. (author)

Mechanical Properties of a Newly Additive Manufactured Implant Material Based on Ti-42Nb

Directory of Open Access Journals (Sweden)

Christian Schulze

2018-01-01

Full Text Available The application of Ti-6Al-4V alloy or commercially pure titanium for additive manufacturing enables the fabrication of complex structural implants and patient-specific implant geometries. However, the difference in Young’s modulus of α + β-phase Ti alloys compared to the human bone promotes stress-shielding effects in the implant–bone interphase. The aim of the present study is the mechanical characterization of a new pre-alloyed β-phase Ti-42Nb alloy for application in additive manufacturing. The present investigation focuses on the mechanical properties of SLM-printed Ti-42Nb alloy in tensile and compression tests. In addition, the raw Ti-42Nb powder, the microstructure of the specimens prior to and after compression tests, as well as the fracture occurring in tensile tests are characterized by means of the SEM/EDX analysis. The Ti-42Nb raw powder exhibits a dendrite-like Ti-structure, which is melted layer-by-layer into a microstructure with a very homogeneous distribution of Nb and Ti during the SLM process. Tensile tests display Young’s modulus of 60.51 ± 3.92 GPa and an ultimate tensile strength of 683.17 ± 16.67 MPa, whereas, under a compressive load, a compressive strength of 1330.74 ± 53.45 MPa is observed. The combination of high mechanical strength and low elastic modulus makes Ti-42Nb an interesting material for orthopedic and dental implants. The spherical shape of the pre-alloyed material additionally allows for application in metal 3D printing, enabling the fabrication of patient-specific structural implants.

Newborn Screening Tests

Science.gov (United States)

... don't have enough biotinidase, an enzyme that recycles biotin (a B vitamin) in the body. Biotinidase ... about additional tests: Do you have a family history of an inherited disorder? Have you previously given ...

Limitations of metformin use in patients with kidney disease: are they warranted?

Science.gov (United States)

Vasisht, K P; Chen, S-C; Peng, Y; Bakris, G L

2010-12-01

To show that metformin, one of the most widely used agents, is contraindicated in patients with diabetes having chronic kidney disease (CKD) (i.e. serum creatinine >1.5 mg/dl) secondary to fear of lactic acidosis. The overall incidence of lactic acidosis is estimated at an upper limit of eight cases per 100 000 patient-years. We evaluated metformin use in two cohorts, one from the University of Chicago Diabetes Center and the other from National Health and Nutrition Examination Survey (NHANES) 1999-2006. Estimated glomerular filtration rate (eGFR) was calculated using the re-expressed Modification of Diet in Renal Disease (MDRD) Study equation and compared to serum creatinine. We hypothesized that metformin is used in patients with undetected advanced CKD (i.e. serum creatinine is ≥1.5 mg/dl). A chi-squared test was used to compare per cent differences of metformin use across demographic variables and eGFR in the NHANES cohort. At the University of Chicago Diabetes Center, 36 of 234 (15.3%) patients with an eGFR of metformin. Data from NHANES, age >18 years and eGFR metformin. We conclude that metformin utilization occurs with a higher frequency than predicted by serum creatinine in people with eGFR <60 ml/min/1.73 m(2) . Given the very low incidence of lactic acidosis, the recommendation should be changed to reflect eGFR cut-off values rather than serum creatinine. © 2010 Blackwell Publishing Ltd.

Testing a Model of Functional Impairment in Telephone Crisis Support Workers.

Science.gov (United States)

Kitchingman, Taneile A; Wilson, Coralie J; Caputi, Peter; Wilson, Ian; Woodward, Alan

2017-11-01

It is well known that helping professionals experience functional impairment related to elevated symptoms of psychological distress as a result of frequent empathic engagement with distressed others. Whether telephone crisis support workers are impacted in a similar way is not currently reported in the literature. The purpose of this study was to test a hypothesized model of factors contributing to functional impairment in telephone crisis support workers. A national sample of 210 telephone crisis support workers completed an online survey including measures of emotion regulation, symptoms of general psychological distress and suicidal ideation, intentions to seek help for symptoms, and functional impairment. Structural equation modeling was used to test the fit of the data to the hypothesized model. Goodness-of-fit indices were adequate and supported the interactive effects of emotion regulation, general psychological distress, suicidal ideation, and intentions to seek help for ideation on functional impairment. These results warrant the deliberate management of telephone crisis support workers' impairment through service selection, training, supervision, and professional development strategies. Future research replicating and extending this model will further inform the modification and/or development of strategies to optimize telephone crisis support workers' well-being and delivery of support to callers.

Joint additive effects of temperature and UVB radiation on zoeae of the crab Taliepus dentatus

KAUST Repository

Carreja, B

2016-04-06

Warming and enhanced ultraviolet B (UVB) radiation are 2 global stressors acting across the ocean. We tested their effects on the survival and performance (consumption rates and activity) on the zoea I stage of the Chilean kelp crab Taliepus dentatus. Our goal was to resolve whether these stressors, when acting concurrently, had additive or interactive effects, either synergistic or antagonistic. A multifactorial experiment of 4 temperatures and 3 UVB irradiance levels was run. The larvae showed a significant increase in mortality with increasing temperature. Exposure to UVB reduced the thermal tolerance of the larvae by a significant increase of their mortality rate. Oxygen consumption increased as temperature increased. When exposed to UVB radiation, larval oxygen consumption increased significantly for all the temperatures tested. Two statistical models of joint effects confirmed that the combined effect of both stressors was additive, with no interaction, either synergistic or antagonistic. One of them, the independent action (IA) model, also revealed that concurrent effects on mortality remained additive when doubling the UVB dose. Additivity of the stressors improved the predictability of their effects on larval mortality. Exposure to UVB radiation increased mortality rates by 1.5 times at any temperature tested, independently of the dose. © The authors 2016.

Joint additive effects of temperature and UVB radiation on zoeae of the crab Taliepus dentatus

KAUST Repository

Carreja, B; Ferná ndez, M; Agusti, Susana

2016-01-01

Warming and enhanced ultraviolet B (UVB) radiation are 2 global stressors acting across the ocean. We tested their effects on the survival and performance (consumption rates and activity) on the zoea I stage of the Chilean kelp crab Taliepus dentatus. Our goal was to resolve whether these stressors, when acting concurrently, had additive or interactive effects, either synergistic or antagonistic. A multifactorial experiment of 4 temperatures and 3 UVB irradiance levels was run. The larvae showed a significant increase in mortality with increasing temperature. Exposure to UVB reduced the thermal tolerance of the larvae by a significant increase of their mortality rate. Oxygen consumption increased as temperature increased. When exposed to UVB radiation, larval oxygen consumption increased significantly for all the temperatures tested. Two statistical models of joint effects confirmed that the combined effect of both stressors was additive, with no interaction, either synergistic or antagonistic. One of them, the independent action (IA) model, also revealed that concurrent effects on mortality remained additive when doubling the UVB dose. Additivity of the stressors improved the predictability of their effects on larval mortality. Exposure to UVB radiation increased mortality rates by 1.5 times at any temperature tested, independently of the dose. © The authors 2016.

Mitigation of Humic Acid Inhibition in Anaerobic Digestion of Cellulose by Addition of Various Salts

Directory of Open Access Journals (Sweden)

Samet Azman

2015-03-01

Full Text Available Humic compounds are inhibitory to the anaerobic hydrolysis of cellulosic biomass. In this study, the impact of salt addition to mitigate the inhibitory effects of humic compounds was investigated. The experiment was conducted using batch tests to monitor the anaerobic hydrolysis of cellulose in the presence of humic acid. Sodium, potassium, calcium, magnesium and iron salts were tested separately for their efficiency to mitigate humic acid inhibition. All experiments were done under mesophilic conditions (30 °C and at pH 7. Methane production was monitored online, using the Automatic Methane Potential Test System. Methane production, soluble chemical oxygen demand and volatile fatty acid content of the samples were measured to calculate the hydrolysis efficiencies. Addition of magnesium, calcium and iron salts clearly mitigated the inhibitory effects of humic acid and hydrolysis efficiencies reached up to 75%, 65% and 72%, respectively, which were similar to control experiments. Conversely, potassium and sodium salts addition did not mitigate the inhibition and hydrolysis efficiencies were found to be less than 40%. Mitigation of humic acid inhibition via salt addition was also validated by inductively coupled plasma atomic emission spectroscopy analyses, which showed the binding capacity of different cations to humic acid.

FFTF utilization for irradiation testing

International Nuclear Information System (INIS)

Corrigan, D.C.; Julyk, L.J.; Hoth, C.W.; McGuire, J.C.; Sloan, W.R.

1980-01-01

FFTF utilization for irradiation testing is beginning. Two Fuels Open Test Assemblies and one Vibration Open Test Assembly, both containing in-core contact instrumentation, are installed in the reactor. These assemblies will be used to confirm plant design performance predictions. Some 100 additional experiments are currently planned to follow these three. This will result in an average core loading of about 50 test assemblies throughout the early FFTF operating cycles

Measurement of fracture toughness of metallic materials produced by additive manufacturing

Science.gov (United States)

Quénard, O.; Dorival, O.; Guy, Ph.; Votié, A.; Brethome, K.

2018-04-01

This study focuses on the microstructure and mechanical properties of metallic materials produced by additive layer manufacturing (ALM), especially the laser beam melting process. The influence of the specimen orientation during the ALM process and that of two post-build thermal treatments were investigated. The identified metal powder is Ti-6Al-4V (titanium base). Metallographic analysis shows their effects on the microstructure of the metals. Mechanical experiments involving tensile tests as well as toughness tests were performed according to ASTM (American Society for Testing and Materials) norms. The results show that the main influence is that of the thermal treatments; however the manufacturing stacking direction may lead to some anisotropy in the mechanical properties.

Common Data Acquisition Systems (DAS) Software Development for Rocket Propulsion Test (RPT) Test Facilities

Science.gov (United States)

Hebert, Phillip W., Sr.; Davis, Dawn M.; Turowski, Mark P.; Holladay, Wendy T.; Hughes, Mark S.

2012-01-01

The advent of the commercial space launch industry and NASA's more recent resumption of operation of Stennis Space Center's large test facilities after thirty years of contractor control resulted in a need for a non-proprietary data acquisition systems (DAS) software to support government and commercial testing. The software is designed for modularity and adaptability to minimize the software development effort for current and future data systems. An additional benefit of the software's architecture is its ability to easily migrate to other testing facilities thus providing future commonality across Stennis. Adapting the software to other Rocket Propulsion Test (RPT) Centers such as MSFC, White Sands, and Plumbrook Station would provide additional commonality and help reduce testing costs for NASA. Ultimately, the software provides the government with unlimited rights and guarantees privacy of data to commercial entities. The project engaged all RPT Centers and NASA's Independent Verification & Validation facility to enhance product quality. The design consists of a translation layer which provides the transparency of the software application layers to underlying hardware regardless of test facility location and a flexible and easily accessible database. This presentation addresses system technical design, issues encountered, and the status of Stennis development and deployment.

HANFORD CONTAINERIZED CAST STONE FACILITY TASK 1 PROCESS TESTING & DEVELOPMENT FINAL TEST REPORT

Energy Technology Data Exchange (ETDEWEB)

LOCKREM, L L

2005-07-13

Laboratory testing and technical evaluation activities on Containerized Cast Stone (CCS) were conducted under the Scope of Work (SOW) contained in CH2M HILL Hanford Group, Inc. (CHG) Contract No. 18548 (CHG 2003a). This report presents the results of testing and demonstration activities discussed in SOW Section 3.1, Task I--''Process Development Testing'', and described in greater detail in the ''Containerized Grout--Phase I Testing and Demonstration Plan'' (CHG, 2003b). CHG (2003b) divided the CCS testing and evaluation activities into six categories, as follows: (1) A short set of tests with simulant to select a preferred dry reagent formulation (DRF), determine allowable liquid addition levels, and confirm the Part 2 test matrix. (2) Waste form performance testing on cast stone made from the preferred DRF and a backup DRF, as selected in Part I, and using low activity waste (LAW) simulant. (3) Waste form performance testing on cast stone made from the preferred DRF using radioactive LAW. (4) Waste form validation testing on a selected nominal cast stone formulation using the preferred DRF and LAW simulant. (5) Engineering evaluations of explosive/toxic gas evolution, including hydrogen, from the cast stone product. (6) Technetium ''getter'' testing with cast stone made with LAW simulant and with radioactive LAW. In addition, nitrate leaching observations were drawn from nitrate leachability data obtained in the course of the Parts 2 and 3 waste form performance testing. The nitrate leachability index results are presented along with other data from the applicable activity categories.

Additive Manufacturing and Characterization of Ultem Polymers and Composites

Science.gov (United States)

Chuang, Kathy C.; Grady, Joseph E.; Draper, Robert D.; Shin, Euy-Sik E.; Patterson, Clark; Santelle, Thomas D.

2015-01-01

The objective of this project was to conduct additive manufacturing to produce aircraft engine components by Fused Deposition Modeling (FDM), using commercially available polyetherimides - Ultem 9085 and experimental Ultem 1000 mixed with 10 percent chopped carbon fiber. A property comparison between FDM-printed and injection-molded coupons for Ultem 9085, Ultem 1000 resin and the fiber-filled composite Ultem 1000 was carried out. Furthermore, an acoustic liner was printed from Ultem 9085 simulating conventional honeycomb structured liners and tested in a wind tunnel. Composite compressor inlet guide vanes were also printed using fiber-filled Ultem 1000 filaments and tested in a cascade rig. The fiber-filled Ultem 1000 filaments and composite vanes were characterized by scanning electron microscope (SEM) and acid digestion to determine the porosity of FDM-printed articles which ranged from 25-31 percent. Coupons of Ultem 9085 and experimental Ultem 1000 composites were tested at room temperature and 400 degrees Fahrenheit to evaluate their corresponding mechanical properties.

[Food additives and healthiness].

Science.gov (United States)

Heinonen, Marina

2014-01-01

Additives are used for improving food structure or preventing its spoilage, for example. Many substances used as additives are also naturally present in food. The safety of additives is evaluated according to commonly agreed principles. If high concentrations of an additive cause adverse health effects for humans, a limit of acceptable daily intake (ADI) is set for it. An additive is a risk only when ADI is exceeded. The healthiness of food is measured on the basis of nutrient density and scientifically proven effects.