WorldWideScience

Sample records for warmer infra-med technologies

  1. Infant incubators and radiant warmers.

    Science.gov (United States)

    Bell, E F

    1983-10-01

    Incubators and radiant warmers are used to maintain the body temperature of newborn infants. This is best done so that the energy expended for metabolic heat production is minimized. The heat output of these devices is usually regulated by servocontrol to keep the skin temperature constant at a site on the abdomen where a thermistor probe is attached. In incubators, air temperature can also be controlled as an alternative to skin temperature servocontrol. Increased ambient humidity, heat shields and clothing have been used to decrease the evaporative or nonevaporative heat loss of infants in incubators under certain conditions. Double-walled incubators, by adding a second inner layer of Plexiglas, reduce radiant heat loss. They may also reduce total heat loss, but only if air temperature is controlled rather than skin temperature. The minimal oxygen consumption under a radiant warmer is the same or perhaps slightly higher than it is for the same infant in an incubator. Compared with incubators, the partition of body heat loss is quite different under radiant warmers. Radiant warmers increase convective and evaporative heat loss and insensible water loss but eliminate radiant heat loss or change it to net gain. A heat shield of thin polyethylene film can be used with a radiant warmer to reduce heat loss by convection and evaporation. The major advantage of the radiant warmer is the easy access it provides to critically-ill infants without disturbing the thermal environment. Its major disadvantage is the increase in insensible water loss produced by the radiant warmer. Most infants can be safely and adequately cared for in either incubator or radiant warmer bed.

  2. Behind the Curtain: Keeping Surgical Patients Warmer Fights Infection

    Science.gov (United States)

    ... Cleveland Clinic, Ohio Photo courtesy of NIGMS Keeping Surgical Patients Warmer Fights Infection As recently as the mid- ... His research led to a new conclusion: Keep surgical patients warm. No new drugs, no fancy technology. Warming ...

  3. Winter ENSO teleconnections in a warmer climate

    Energy Technology Data Exchange (ETDEWEB)

    Herceg Bulic, Ivana [Faculty of Science, University of Zagreb, Andrija Mohorovicic Geophysical Institute, Department of Geophysics, Zagreb (Croatia); Brankovic, Cedo [Croatian Meteorological and Hydrological Service (DHMZ), Zagreb (Croatia); Kucharski, Fred [The Abdus Salam International Centre for Theoretical Physics, Trieste (Italy)

    2012-04-15

    Changes in the winter atmospheric response to sea surface temperature (SST) anomalies associated with the El Nino-Southern Oscillation (ENSO) in a warmer climate conditions are estimated from the two 20-member ensembles made by an atmospheric general circulation model of intermediate complexity. Warmer climate is simulated by a modification in the radiation parameterisation that corresponds to the doubled CO{sub 2} concentration, and SST forcing is represented by the same SST anomalies as in current climate (1855-2002) experiment superimposed on the climatological SST that was obtained from a complex atmosphere-ocean general circulation model forced with the doubled CO{sub 2}. SST anomalies in the Nino3.4 region, categorised into five classes, enabled a composite analysis of changes in the Northern Hemisphere tropical/extratropical teleconnections. The main features of the tropical-extratropical teleconnections are maintained in both experiments; for example, irrespective of the sign of SST anomalies, the amplitude of the atmospheric response is positively correlated with the intensity of ENSO event and the El Nino impact is stronger than that of La Nina of the same intensity. The strongest extratropical signal in the warmer climate, particularly significant for strong warm events, is found over the Pacific/North American region; however, this extratropical teleconnections is reduced in a warmer climate relative to the current climate. Over the North Atlantic/European region, a detectable signal linked to ENSO is found; this model response is significantly strengthened in the experiment with the doubled CO{sub 2} concentration. Such an atmospheric response in a warmer climate is found to be associated with changes in the mean state followed as well as in the jet waveguiding effect and stationary wave activity. (orig.)

  4. Terrestrial ecosystems under warmer and drier climates

    Science.gov (United States)

    Pan, Y.

    2016-12-01

    Future warmer and drier climates will likely affect many of the world's terrestrial ecosystems. These changes will fundamentally reshape terrestrial systems through their components and across organization levels. However, it is unclear to what extent terrestrial ecosystems would be resilient enough to stay put to increased temperature and water stress by only adjusting carbon fluxes and water balances? And to what extent it would reach the thresholds at which terrestrial ecosystems were forced to alter species compositions and ecosystem structures for adapting to newer climates? The energy balance of terrestrial ecosystems link thermal and water conditions to defines terrestrial carbon processes and feedbacks to climate, which will inevitably change under warmer and drier climates. Recent theoretical studies provide a new framework, suggesting that terrestrial ecosystems were capable of balancing costs of carbon gain and water transport to achieve optimums for functioning and distribution. Such a paradigm is critical for understanding the dynamics of future terrestrial ecosystems under climate changes, and facilitate modeling terrestrial ecosystems which needs generalized principles for formulating ecosystem behaviors. This study aims to review some recent studies that explore responses of terrestrial ecosystems to rather novel climate conditions, such as heat-induced droughts, intending to provide better comprehension of complex carbon-water interactions through plants to an ecosystem, and relevant factors that may alleviate or worsen already deteriorated climates such as elevated CO2 and soil conditions.

  5. Climate change and river temperature sensitivity to warmer nighttime vs. warmer daytime air temperatures

    Science.gov (United States)

    Diabat, M.; Haggerty, R.; Wondzell, S. M.

    2011-12-01

    We investigated the July river temperature response to atmospheric warming over the diurnal cycle in a 36 km reach of the upper Middle Fork John Day River of Oregon, USA. The physical model Heat Source was calibrated and used to run 3 different cases of increased air temperature during July: 1) uniform increase over the whole day ("delta method"), 2) warmer daytime, and 3) warmer nighttime. All 3 cases had the same mean daily air temperatures - a 4 °C increase relative to 2002. Results show that the timing of air temperature increases has a significant effect on the magnitude, timing and duration of changes in water temperatures relative to current conditions. In all cases, river temperatures in the lower reach increased by at least 1.1 °C . For the delta case, water temperature increases never exceeded 2.3 °C. In contrast, under the warmer daytime case, water temperature increases exceeded 2.3 °C for 6.6 hours/day on average, with the largest increases occurring during mid-day. In the warmer night case the river temperature increases exceeded 2.3 °C for 4.3 hours/day on average with the largest increases occurring around midnight. In addition, an average increase of 4 °C in air temperature under the delta case increased the water temperature by an average of 1.9 °C uniformly during daytime and nighttime. Still, an average increase of 4 °C in air temperature under the warmer daytime case increased water temperature by an average of at least 1.6 °C during the daytime and by an average of up to 2.5 °C during the nighttime, while an average increase of 4 °C in air temperature under the warmer nighttime case increased the water temperature by an average of at least 1.4 °C during the nighttime and by an average of up to 2.4 °C during the daytime. The spatial response of temperature was different for each case. The lower 13 rkm warmed by at least 1.1 °C with the delta case, while only the lower 6 rkm warmed by at least 1.1 °C with the warmer daytime case

  6. Agroecosystem productivity in a warmer and CO2 enriched atmosphere

    Science.gov (United States)

    Bernacchi, Carl; Köhler, Iris; Ort, Donald; Long, Steven; Clemente, Thomas

    2017-04-01

    A number of in-field manipulative experiments have been conducted that address the response of key ecosystem services of major agronomic species to rising CO2. Global warming, however, is inextricably linked to rising greenhouse gases in general, of which CO2 is the most dominant. Therefore, agroecosystem functioning in future conditions requires an understanding of plant responses to both rising CO2 and increased temperatures. Few in-field manipulative experiments have been conducted that supplement both heating and CO2 above background concentrations. Here, the results of six years of experimentation using a coupled Free Air CO2 Enrichment (FACE) technology with variable output infrared heating arrays are reported. The manipulative experiment increased temperatures (+ 3.5˚ C) and CO2 (+ 200 μmol mol-1) above background levels for on two major agronomic crop species grown throughout the world, Zea mays (maize) and Glycine max (soybean). The first phase of this research addresses the response of plant physiological parameters to growth in elevated CO2 and warmer temperatures for maize and soybean grown in an open-air manipulative experiment. The results show that any increase in ecosystem productivity associated with rising CO2 is either similar or is offset by growth at higher temperatures, inconsistent with the perceived benefits of higher CO2 plus warmer temperatures on agroecosystem productivity. The second phase of this research addresses the opportunity to genetically modify soybean to allow for improved productivity under high CO2 and warmer temperatures by increasing a key photosynthetic carbon reduction cycle enzyme, SPBase. The results from this research demonstrates that manipulation of the photosynthetic pathway can lead to higher productivity in high CO2 and temperature relative to the wild-type control soybean. Overall, this research advances the understanding of the physiological responses of two major crops, and the impact on ecosystem services

  7. Thermoregulation: incubators, radiant warmers, artificial skins, and body hoods.

    Science.gov (United States)

    LeBlanc, M H

    1991-09-01

    Keeping babies warm whether using incubator or radiant warmers is important in optimizing their chances of survival. Many design changes have occurred in devices for keeping babies warm, while few controlled studies using clinically important end points have been conducted to assess these changes. Radiant warmers produce larger evaporative heat and water losses and slightly higher basal metabolic rate than incubators. The clinical significance of the higher metabolic rate is uncertain. The water losses create an additional problem in managing infants under radiant warmers. The use of hoods made of thin plastic films to raise local humidity and reduce evaporative water loss helps control this problem. In incubators, humidity may be necessary to provide a warm enough environment for the most immature infants. Artificial skins as yet have not supplanted body hoods for this purpose. Both incubators and radiant warmers produce temperature instability when used as skin servocontrolled devices. There are, however, no data currently available to say how much thermal instability can be well tolerated by a baby. Too much thermal instability produces apnea and increased mortality. Air servocontrolling an incubator reduces environmental temperature instability.

  8. 78 FR 61383 - Certain Thermal Support Devices For Infants, Infant Incubators, Infant Warmers, and Components...

    Science.gov (United States)

    2013-10-03

    ... COMMISSION Certain Thermal Support Devices For Infants, Infant Incubators, Infant Warmers, and Components... United States after importation of certain thermal support devices for infants, infant incubators, infant... certain thermal support devices for infants, infant incubators, infant warmers, and components thereof...

  9. 78 FR 54911 - Certain Thermal Support Devices for Infants, Infant Incubators, Infant Warmers and Components...

    Science.gov (United States)

    2013-09-06

    ... COMMISSION Certain Thermal Support Devices for Infants, Infant Incubators, Infant Warmers and Components.... International Trade Commission has received a complaint entitled Certain Thermal Support Devices for Infants, Infant Incubators, Infant Warmers and Components Thereof, DN 2976; the Commission is soliciting...

  10. Model biases in rice phenology under warmer climates.

    Science.gov (United States)

    Zhang, Tianyi; Li, Tao; Yang, Xiaoguang; Simelton, Elisabeth

    2016-06-07

    Climate-induced crop yields model projections are constrained by the accuracy of the phenology simulation in crop models. Here, we use phenology observations from 775 trials with 19 rice cultivars in 5 Asian countries to compare the performance of four rice phenology models (growing-degree-day (GDD), exponential, beta and bilinear models) when applied to warmer climates. For a given cultivar, the difference in growing season temperature (GST) varied between 2.2 and 8.2 °C in different trials, which allowed us to calibrate the models for lower GST and validate under higher GST, with three calibration experiments. The results show that in warmer climates the bilinear and beta phenology models resulted in gradually increasing bias for phenology predication and double yield bias per percent increase in phenology simulation bias, while the GDD and exponential models maintained a comparatively constant bias. The phenology biases were primarily attributed to varying phenological patterns to temperature in models, rather than on the size of the calibration dataset. Additionally, results suggest that model simulations based on multiple cultivars provide better predictability than using one cultivar. Therefore, to accurately capture climate change impacts on rice phenology, we recommend simulations based on multiple cultivars using the GDD and exponential phenology models.

  11. Model biases in rice phenology under warmer climates

    Science.gov (United States)

    Zhang, Tianyi; Li, Tao; Yang, Xiaoguang; Simelton, Elisabeth

    2016-06-01

    Climate-induced crop yields model projections are constrained by the accuracy of the phenology simulation in crop models. Here, we use phenology observations from 775 trials with 19 rice cultivars in 5 Asian countries to compare the performance of four rice phenology models (growing-degree-day (GDD), exponential, beta and bilinear models) when applied to warmer climates. For a given cultivar, the difference in growing season temperature (GST) varied between 2.2 and 8.2 °C in different trials, which allowed us to calibrate the models for lower GST and validate under higher GST, with three calibration experiments. The results show that in warmer climates the bilinear and beta phenology models resulted in gradually increasing bias for phenology predication and double yield bias per percent increase in phenology simulation bias, while the GDD and exponential models maintained a comparatively constant bias. The phenology biases were primarily attributed to varying phenological patterns to temperature in models, rather than on the size of the calibration dataset. Additionally, results suggest that model simulations based on multiple cultivars provide better predictability than using one cultivar. Therefore, to accurately capture climate change impacts on rice phenology, we recommend simulations based on multiple cultivars using the GDD and exponential phenology models.

  12. Evidence for warmer interglacials in East Antarctic ice cores.

    Science.gov (United States)

    Sime, L C; Wolff, E W; Oliver, K I C; Tindall, J C

    2009-11-19

    Stable isotope ratios of oxygen and hydrogen in the Antarctic ice core record have revolutionized our understanding of Pleistocene climate variations and have allowed reconstructions of Antarctic temperature over the past 800,000 years (800 kyr; refs 1, 2). The relationship between the D/H ratio of mean annual precipitation and mean annual surface air temperature is said to be uniform +/-10% over East Antarctica and constant with time +/-20% (refs 3-5). In the absence of strong independent temperature proxy evidence allowing us to calibrate individual ice cores, prior general circulation model (GCM) studies have supported the assumption of constant uniform conversion for climates cooler than that of the present day. Here we analyse the three available 340 kyr East Antarctic ice core records alongside input from GCM modelling. We show that for warmer interglacial periods the relationship between temperature and the isotopic signature varies among ice core sites, and that therefore the conversions must be nonlinear for at least some sites. Model results indicate that the isotopic composition of East Antarctic ice is less sensitive to temperature changes during warmer climates. We conclude that previous temperature estimates from interglacial climates are likely to be too low. The available evidence is consistent with a peak Antarctic interglacial temperature that was at least 6 K higher than that of the present day -approximately double the widely quoted 3 +/- 1.5 K (refs 5, 6).

  13. A much warmer Earth surface for most of geologic time: implications to biotic weathering

    Science.gov (United States)

    Schwartzman, D. W.; McMenamin, M.

    1993-01-01

    The authors present two scenarios for the temperature history of Earth. One scenario is conventional, the other relies on a warmer history. Both scenarios include surface cooling determined by the evolution of the biosphere and are similar until the Proterozoic period. The warmer scenario requires a higher plant/lichen terrestrial biota to increase weathering intensity. Justification for a warmer surface includes period temperatures from the oxygen isotope record of coexisting phosphates and cherts, an upper limit of 58 degrees C from primary gypsum precipitation, and the lack of fractionation of sulfur isotopes between sulfide and sulfates in Archean sediments.

  14. A much warmer Earth surface for most of geologic time: implications to biotic weathering

    Science.gov (United States)

    Schwartzman, D. W.; McMenamin, M.

    1993-01-01

    The authors present two scenarios for the temperature history of Earth. One scenario is conventional, the other relies on a warmer history. Both scenarios include surface cooling determined by the evolution of the biosphere and are similar until the Proterozoic period. The warmer scenario requires a higher plant/lichen terrestrial biota to increase weathering intensity. Justification for a warmer surface includes period temperatures from the oxygen isotope record of coexisting phosphates and cherts, an upper limit of 58 degrees C from primary gypsum precipitation, and the lack of fractionation of sulfur isotopes between sulfide and sulfates in Archean sediments.

  15. Pressure Infusion Cuff and Blood Warmer during Massive Transfusion: An Experimental Study About Hemolysis and Hypothermia.

    Science.gov (United States)

    Poder, Thomas G; Pruneau, Denise; Dorval, Josée; Thibault, Louis; Fisette, Jean-François; Bédard, Suzanne K; Jacques, Annie; Beauregard, Patrice

    2016-01-01

    Blood warmers were developed to reduce the risk of hypothermia associated with the infusion of cold blood products. During massive transfusion, these devices are used with compression sleeve, which induce a major stress to red blood cells. In this setting, the combination of blood warmer and compression sleeve could generate hemolysis and harm the patient. We conducted this study to compare the impact of different pressure rates on the hemolysis of packed red blood cells and on the outlet temperature when a blood warmer set at 41.5°C is used. Pressure rates tested were 150 and 300 mmHg. Ten packed red blood cells units were provided by Héma-Québec and each unit was sequentially tested. We found no increase in hemolysis either at 150 or 300 mmHg. By cons, we found that the blood warmer was not effective at warming the red blood cells at the specified temperature. At 150 mmHg, the outlet temperature reached 37.1°C and at 300 mmHg, the temperature was 33.7°C. To use a blood warmer set at 41.5°C in conjunction with a compression sleeve at 150 or 300 mmHg does not generate hemolysis. At 300 mmHg a blood warmer set at 41.5°C does not totally avoid a risk of hypothermia.

  16. In-line pressure within a HOTLINE® Fluid Warmer, under various flow conditions.

    Science.gov (United States)

    Higashi, Midoriko; Yamaura, Ken; Matsubara, Yukie; Fukudome, Takuya; Hoka, Sumio

    2015-04-01

    Roller pump infusion devices are widely used for rapid infusion, and may be combined with separate warming devices. There may be instances however, where the pressures generated by the roller pump may not be compatible with the warming device. We assessed a commonly used roller pump in combination with a HOTLINE® Fluid Warmer, and found that it could generate pressures exceeding the HOTLINE® manufacturers specifications. This was of concern because the HOTLINE® manufacturer guideline states that not for use with pressure devices generating over 300 mmHg. Pressure greater than 300 mmHg may compromise the integrity of the HOTLINE® Fluid Warming Set. The aim of this study was to compare in-line pressure within a HOTLINE® Fluid Warmer at different infusion rates of a roller pump using various sizes of intravenous cannulae. The rapid infusion system comprised a 500 mL-normal saline bag, roller pump type infusion device, HOTLINE® Fluid Warmer (blood and fluid warmer system), and six different sizes of intravenous cannulae. In-line pressure was measured proximal to the HOTLINE® (pre-warmer) and proximal to the cannula (post-warmer), at flow rate of 50-160 mL/min. The in-line pressures increased significantly with increasing flow rate. The pre-warmer pressures exceeded 300 mmHg when the flow rate was ≥120 mL/min with 20-gauge, 48 mm length cannula, 130 with 20-gauge, 25 mm cannula, and 160 mL/min with 18-gauge, 48 mm cannula. However, they were HOTLINE® could exceed 300 mmHg, depending on the flow rate and size and length of cannula. It is important to pay attention to the size and length of cannulae and flow rate to keep the maximum in-line pressure<300 mmHg when a roller pump type infusion device is used.

  17. Severe Autumn storms in future Western Europe with a warmer Atlantic Ocean

    NARCIS (Netherlands)

    Baatsen, Michiel; Haarsma, Reindert J.; Van Delden, Aarnout J.; De Vries, Hylke

    2014-01-01

    Simulations with a very high resolution (~25 km) global climate model indicate that more severe Autumn storms will impact Europe in a warmer future climate. The observed increase is mainly attributed to storms with a tropical origin, especially in the later part of the twentyfirst century. As their

  18. Wildlife as reservoirs for vector borne diseases in a warmer Scandinavian climate

    DEFF Research Database (Denmark)

    Bødker, Rene; Kristensen, Birgit

    The distribution of vector borne diseases is highly determined by environmental and climatic parameters. As the climate becomes warmer the potential for spread of exotic vector borne diseases may therefore increase in the Nordic countries. But this does not mean that all new outbreaks of diseases...

  19. Experimental Study of Isothermal Plate Uniformity for Blood Warmer Development using Geothermal Energy

    Science.gov (United States)

    Hendrarsakti, J.; Ichsan, Y.

    2016-09-01

    This research was conducted to assess the direct use of geothermal energy for blood warmer. The heating plate was made form aluminium plates with dimensions of 100 x 200 mm and then fed from the hot water heater. Tests were conducted in the laboratory where geothermal source water is replaced with the heat generated from the heater. The hot water from the heater in the temperature range 55°C - 60°C flowed into vertical chamber. Setting the temperature of the hot water heater is done by changing the flow of hot water coming out of the heater. Results showed that the value of a standard deviation of plate temperature was about 0.42 °C, so it can be said isothermal accordance with design requirement and objective. The test data used for the analysis of the manufacture of the heating plate in the blood warmer to regulate the discharge of hot water at intervals of 21.47 mL/s to 24.8 mL/s to obtain a temperature of 37.20 °C - 40.15 °C. Geothermal energy has the potential for blood warmer because blood warmer is part of the energy cascade in a temperature range of 40°C to 60°C

  20. Epidemic malaria and warmer temperatures in recent decades in an East African highland

    NARCIS (Netherlands)

    Alonso, David; Bouma, Menno J.; Pascual, Mercedes

    2011-01-01

    Climate change impacts on malaria are typically assessed with scenarios for the long-term future. Here we focus instead on the recent past (1970-2003) to address whether warmer temperatures have already increased the incidence of malaria in a highland region of East Africa. Our analyses rely on a

  1. Biases in simulation of the rice phenology models when applied in warmer climates

    Science.gov (United States)

    Zhang, T.; Li, T.; Yang, X.; Simelton, E.

    2015-12-01

    The current model inter-comparison studies highlight the difference in projections between crop models when they are applied to warmer climates, but these studies do not provide results on how the accuracy of the models would change in these projections because the adequate observations under largely diverse growing season temperature (GST) are often unavailable. Here, we investigate the potential changes in the accuracy of rice phenology models when these models were applied to a significantly warmer climate. We collected phenology data from 775 trials with 19 cultivars in 5 Asian countries (China, India, Philippines, Bangladesh and Thailand). Each cultivar encompasses the phenology observations under diverse GST regimes. For a given rice cultivar in different trials, the GST difference reaches 2.2 to 8.2°C, which allows us to calibrate the models under lower GST and validate under higher GST (i.e., warmer climates). Four common phenology models representing major algorithms on simulations of rice phenology, and three model calibration experiments were conducted. The results suggest that the bilinear and beta models resulted in gradually increasing phenology bias (Figure) and double yield bias per percent increase in phenology bias, whereas the growing-degree-day (GDD) and exponential models maintained a comparatively constant bias when applied in warmer climates (Figure). Moreover, the bias of phenology estimated by the bilinear and beta models did not reduce with increase in GST when all data were used to calibrate models. These suggest that variations in phenology bias are primarily attributed to intrinsic properties of the respective phenology model rather than on the calibration dataset. Therefore we conclude that using the GDD and exponential models has more chances of predicting rice phenology correctly and thus, production under warmer climates, and result in effective agricultural strategic adaptation to and mitigation of climate change.

  2. Effect of warming and flow rate conditions of blood warmers on red blood cell integrity.

    Science.gov (United States)

    Poder, T G; Pruneau, D; Dorval, J; Thibault, L; Fisette, J-F; Bédard, S K; Jacques, A; Beauregard, P

    2016-11-01

    Fluid warmers are routinely used to reduce the risk of hypothermia and cardiac complications associated with the infusion of cold blood products. However, warming blood products could generate haemolysis. This study was undertaken to compare the impact of temperature of blood warmers on the per cent haemolysis of packed red blood cells (RBCs) heated at different flow rates as well as non-flow conditions. Infusion warmers used were calibrated at 41·5°C ± 0·5°C and 37·5°C ± 0·5°C. Cold RBC units stored at 4°C in AS-3 (n = 30), aged 30-39 days old, were divided into half units before being allocated under two different scenarios (i.e. infusion pump or syringe). Blood warmers were effective to warm cold RBCs to 37·5°C or 41·5°C when used in conjunction with an infusion pump at flow rate up to 600 ml/h. However, when the warmed blood was held in a syringe for various periods of time, such as may occur in neonatal transfusions, the final temperature was below the expected requirements with measurement as low as 33·1°C. Increasing the flow with an infusion pump increased haemolysis in RBCs from 0·2% to up to 2·1% at a flow rate of 600 ml/h regardless of the warming device used (P < 0·05). No relevant increase of haemolysis was observed using a syringe. The use of a blood warmer adjusted to 41·5°C is probably the best choice for reducing the risk of hypothermia for the patient without generating haemolysis. However, we should be cautious with the use of an infusion pump for RBC transfusion, particularly at high flow rates. © 2016 International Society of Blood Transfusion.

  3. Can latent heat safely warm blood? – in vitro testing of a portable prototype blood warmer

    Directory of Open Access Journals (Sweden)

    McEwen Mark P

    2007-08-01

    Full Text Available Abstract Background Trauma/retrieval patients are often in shock and hypothermic. Treatment of such patients usually involves restoring their blood volume with transfusion of blood (stored at 2°C – 6°C and/or crystalloids or colloids (stored at ambient temperature. Rapid infusion of these cold fluids can worsen or even induce hypothermia in these patients. Warming of intravenous fluids at accident sites has traditionally been difficult due to a lack of suitable portable fluid warmers that are not dependent on mains electrical or battery power. If latent heat, the heat released when a liquid solidifies (an inherently temperature limiting process can warm intravenous fluids, portable devices without a reliance on electrical energy could be used to reduce the incidence of hypothermia in trauma patients. Methods Rapid infusion of red cells into patients was timed to sample typical clinical flow rates. An approved dry heat blood warmer was compared with a prototype blood warmer using a supercooled liquid latent heat storage material, to warm red cells whilst monitoring inlet and outlet temperatures. To determine the effect of warming on red cell integrity compared to the normal storage lesion of blood, extracellular concentrations of potassium, lactate dehydrogenase and haemoglobin were measured in blood which had been warmed after storage at 2°C – 6°C for 1 to 42 days. Results A prototype latent heat fluid warmer consistently warmed red cells from approximately 4°C to approximately 35°C at typical clinical flow rates. Warming of stored blood with latent heat did not affect red cell integrity more than the approved dry heat blood warmer. Conclusion Using latent heat as an energy source can satisfactorily warm cold blood or other intravenous fluids to near body temperature, without any adverse affects.

  4. Evidence for warmer event from quartz grains in the soil of Grove Mountains, East Antarctica

    Institute of Scientific and Technical Information of China (English)

    Yan Xin; Li Xiaoli; Liu Xiaohan; Zhang Ru-fan

    2005-01-01

    The cold desert soil has been discovered at first time in southern ridgeof Mount Harding, Grove Mountains of interior East Antarctica Ice Sheet. Based on the micro structural observation, dominant characteristics of quartz grains include: distinct surface stria and fractures, and clean features of frost action at both of crystal margins and micro crannies of quartz grains. These features show a pedogenesis environment of few water, short transportation and frost action, revealing a warmer climatic event existed in this region.

  5. Chemical Hand Warmer Packet Ingestion: A Case of Elemental Iron Exposure.

    Science.gov (United States)

    Weiland, Jessica L; Sherrow, Leighanne K; Jayant, Deepak A; Katz, Kenneth D

    2017-09-01

    For individuals who work outdoors in the winter or play winter sports, chemical hand warmers are becoming increasingly more commonplace because of their convenience and effectiveness. A 32-year-old woman with a history of chronic pain and bipolar disorder presented to the emergency department complaining of a "warm sensation" in her mouth and epigastrium after reportedly ingesting the partial contents of a chemical hand warmer packet containing between 5 and 8 g of elemental iron. She had been complaining of abdominal pain for approximately 1 month and was prescribed unknown antibiotics the previous day. The patient denied ingestion of any other product or medication other than what was prescribed. A serum iron level obtained approximately 6 hours after ingestion measured 235 micrograms/dL (reference range 40-180 micrograms/dL). As the patient demonstrated no new abdominal complaints and no evidence of systemic iron toxicity, she was discharged uneventfully after education. However, the potential for significant iron toxicity exists depending on the extent of exposure to this or similar products. Treatment for severe iron toxicity may include fluid resuscitation, whole bowel irrigation, and iron chelation therapy with deferoxamine. Physicians should become aware of the toxicity associated with ingestion of commercially available hand warmers. Consultation with a medical toxicologist is recommended. Copyright © 2017 Wilderness Medical Society. Published by Elsevier Inc. All rights reserved.

  6. Honeybees prefer warmer nectar and less viscous nectar, regardless of sugar concentration.

    Science.gov (United States)

    Nicolson, Susan W; de Veer, Leo; Köhler, Angela; Pirk, Christian W W

    2013-09-22

    The internal temperature of flowers may be higher than air temperature, and warmer nectar could offer energetic advantages for honeybee thermoregulation, as well as being easier to drink owing to its lower viscosity. We investigated the responses of Apis mellifera scutellata (10 colonies) to warmed 10% w/w sucrose solutions, maintained at 20-35°C, independent of low air temperatures, and to 20% w/w sucrose solutions with the viscosity increased by the addition of the inert polysaccharide Tylose (up to the equivalent of 34.5% sucrose). Honeybee crop loads increased with nectar temperature, as did the total consumption of sucrose solutions over 2 h by all bees visiting the feeders. In addition, the preference of marked honeybees shifted towards higher nectar temperatures with successive feeder visits. Crop loads were inversely proportional to the viscosity of the artificial nectar, as was the total consumption of sucrose solutions over 2 h. Marked honeybees avoided higher nectar viscosities with successive feeder visits. Bees thus showed strong preferences for both warmer and less viscous nectar, independent of changes in its sugar concentration. Bees may benefit from foraging on nectars that are warmer than air temperature for two reasons that are not mutually exclusive: reduced thermoregulatory costs and faster ingestion times due to the lower viscosity.

  7. The Impact of a Warmer Mediterranean Sea on Central European Summer Flooding

    Science.gov (United States)

    Volosciuk, Claudia; Semenov, Vladimir; Maraun, Douglas; Latif, Mojib; Tilinina, Natalia

    2014-05-01

    Central European climate is influenced by the Mediterranean Sea, which experienced a strong increase in sea surface temperature (SST) during the last four decades. One example of extreme weather events are cyclones following the "Vb" pathway. These cyclones are generated over the Mediterranean Sea and travel northeastwards around the Alps and then hit countries like Poland and Germany. The cyclones carry large amounts of moisture and cause extreme precipitation, and subsequently flooding, particularly in summer. These floods, such as the Elbe flood in 2002, have devastating societal impacts and also influence ecosystems. To analyse the potential impact of increased Mediterranean SST on extreme precipitation in Europe, a series of simulations with the atmospheric general circulation model (AGCM) ECHAM5 has been carried out. ECHAM5 was run at high horizontal resolution (T159) and integrated for 40 years in each experiment. The control run is forced by SST and sea ice concentration (SIC) climatology derived from 1970-1999. A warmer climate is simulated by using global climatological SST and SIC from 2000-2012. To disentangle the impact of the Mediterranean Sea, an additional simulation was performed with the same global SST and SIC as in the control run, but with the warmer 2000-2012 SST climatology restricted to the Mediterranean and Black Seas. 20-season return levels were derived as a measure of extreme precipitation for daily as well as five day precipitation in JJA (June, July, August). These return levels are estimated as quantiles of a stationary generalised extreme value (GEV) distribution. Although the increase in the number of Vb cyclones is only modest, precipitation return levels in JJA show an increase along the Vb cyclone track, for daily (up to approximately 63 %) as well as for five day (up to approximately 76 %) precipitation extremes. This increase can be attributed to the warmer Mediterranean Sea, as it is observed in both the globally warmer and

  8. Continuous rainfall generation for a warmer climate using observed temperature sensitivities

    Science.gov (United States)

    Wasko, Conrad; Sharma, Ashish

    2017-01-01

    Continuous rainfall sequences are often used as inputs in hydrologic modeling, particularly where a probabilistic assessment is required. Continuous rainfall sequences provide a means for accounting of all aspects of rainfall that produce flooding, for example, not just the design rainfall event but also the rainfall prior to the extreme rainfall event. With the advent of climate change, higher temperatures have been associated with changes in rainfall, in particular intensifying rainfall extremes with less uniform temporal patterns. Given these demonstrated changes to extreme rainfall with temperature rise, there is a need to modify continuous rainfall generators to account for current and likely future changes in temperature. In this work we propose a novel method for simulating continuous rainfall sequences for a future warmer climate by conditioning parameters on their historical sensitivity with temperature. To demonstrate the proposed technique we use a one-dimensional Neyman-Scott Rectangular Pulses model at two locations across Australia. The statistics used in the parameter estimation are conditioned on their historical sensitivity to average monthly temperature to simulate rainfall for a change in temperature. The results are validated by comparing the simulated rainfall against observations originating from differing temperatures and it is shown that the model captures the relative difference in the mean monthly rainfall and monthly maxima. Encouraged by these results we simulate rainfall for higher temperatures and capture expected changes to annual maxima and design temporal patterns for a warmer climate. While we demonstrate our methodology in the simulation of sub-daily rainfall using a specific model, the approach presented here can be applied to all weather generation schemes for projection in a warmer climate.

  9. Asymmetric effects of cooler and warmer winters on beech phenology last beyond spring

    Science.gov (United States)

    Signarbieux, Constant; Toledano, Ester; Sangines, Paula; Fu, Yongshuo; Schlaepfer, Rodolphe; Buttler, Alexandre; Vitasse, Yann

    2017-04-01

    In temperate trees, the timing of plant growth onset and cessation affect biogeochemical cycles, water and energy balance. Currently, phenological studies largely focus on specific phenophases and on their responses to warming. How differently spring phenology responds to the warming and cooling, and affects the subsequent phases, has not been well investigated. Here, we exposed saplings of Fagus sylvatica L. to warmer and cooler climate during the winter 2013-2014 by conducting a reciprocal transplant experiment between two elevations (1340 vs. 371 m.a.s.l., ca. 6°C difference) in the Swiss Jura mountains. To test the legacy effects of earlier or later budburst on the budset timing, saplings were moved back to their original elevation shortly after the occurrence of budburst in spring 2014. One degree decrease of air temperature resulted in a delay of 10.9 days in budburst dates, whereas one degree of warming advanced the date by 8.8 days. Interestingly, we found an asymmetric effect of the warmer winter vs. cooler winter on the budset timing in autumn: saplings experiencing a cooler winter showed a delay of 31 days in their budset timing compared to the control, whereas saplings experiencing a warmer winter showed 10 days earlier budset. The dependency of spring over autumn phenophases might be partly explained by the building up of the non-structural carbohydrate storage and suggests that the potential delay in growth cessation due to global warming might be smaller than expected. We did not find a significant correlation in budburst dates between 2014 and 2015, indicating that the legacy effects of the different phenophases might be reset during each winter. Adapting phenological models to the whole annual phenological cycle, and considering the different response to cooling and warming, would improve predictions of tree phenology under future climate warming conditions.

  10. WARMER URBAN CLIMATES FOR DEVELOPMENT OF GREEN SPACES IN NORTHERN SIBERIAN CITIES

    Directory of Open Access Journals (Sweden)

    Igor Esau

    2016-01-01

    Full Text Available Modern human societies have accumulated considerable power to modify their environment and the earth’s system climate as the whole. The most significant environmental changes are found in the urbanized areas. This study considers coherent changes in vegetation productivity and land surface temperature (LST around four northern West Siberian cities, namely, Tazovsky, Nadym, Noyabrsk and Megion. These cities are located in tundra, forest-tundra, northern taiga and middle taiga bioclimatic zones correspondingly. Our analysis of 15 years (2000–2014 Moderate Resolution Imaging Spectroradiometer (MODIS data revealed significantly (1.3 °C to 5.2 °C warmer seasonally averaged LST within the urbanized territories than those of the surrounding landscapes. The magnitude of the urban LST anomaly corresponds to climates found 300–600 km to the South. In the climate change perspective, this magnitude corresponds to the expected regional warming by the middle or the end of the 21st century. Warmer urban climates, and specifically warmer upper soil layers, can support re-vegetation of the disturbed urban landscapes with more productive trees and tall shrubs. This afforestation is welcome by the migrant city population as it is more consistent with their traditional ecological knowledge. Survival of atypical, southern plant species encourages a number of initiatives and investment to introduce even broader spectrum of temperate blossoming trees and shrubs in urban landscapes. The unintended changes of the urban micro-climates in combination with knowledgeable urban planning could transform the Siberian pioneer settlements into places of belonging.

  11. Warmer night-time temperature promotes microbial heterotrophic activity and modifies stream sediment community.

    Science.gov (United States)

    Freixa, Anna; Acuña, Vicenç; Casellas, Maria; Pecheva, Stoyana; Romaní, Anna M

    2017-09-01

    Diel temperature patterns are changing because of global warming, with higher temperatures being predicted to be more pronounced at night. Biological reactions are temperature dependent, with some occurring only during the daylight hours (e.g., light photosynthesis) and other during the entire day (e.g., respiration). Consequently, we expect the modification of daily temperature cycles to alter microbial biological reactions in stream sediments. Here, we aimed to study the effect of warming and changes of the diel temperature patterns on stream sediment biofilm functions tied to organic carbon decomposition, as well as on biofilm meiofaunal community structure. We performed an eight-week experiment with 12 artificial streams subjected to three different diel temperature patterns: warming, warmer nights and control. Significant effects of warming on biofilm function and structure were mainly detected in the long term. Our results showed that warming altered biofilm function, especially in the warmer nights' treatment, which enhanced β-glucosidase enzyme activity. Interestingly, clear opposite diel patterns were observed for dissolved organic carbon and β-glucosidase activity, suggesting that, at night, sediment bacteria quickly consume the input of photosynthetic dissolved organic carbon labile compounds created during light-time. The biofilm structure was also altered by warming, as both warming and warmer night treatments enhanced copepod abundance and diminished abundances of turbellaria and nematodes, which, in turn, controlled bacterial, algal and ciliate communities. Overall, we conclude that warming has strong effect on sediment biofilm structure and enhanced microbial organic matter degradation which might, consequently, affect higher trophic levels and river carbon cycling. © 2017 John Wiley & Sons Ltd.

  12. Honeybees prefer warmer nectar and less viscous nectar, regardless of sugar concentration

    OpenAIRE

    Nicolson, Susan W.; de Veer, Leo; Köhler, Angela; Pirk, Christian W.W.

    2013-01-01

    The internal temperature of flowers may be higher than air temperature, and warmer nectar could offer energetic advantages for honeybee thermoregulation, as well as being easier to drink owing to its lower viscosity. We investigated the responses of Apis mellifera scutellata (10 colonies) to warmed 10% w/w sucrose solutions, maintained at 20–35°C, independent of low air temperatures, and to 20% w/w sucrose solutions with the viscosity increased by the addition of the inert polysaccharide Tylo...

  13. Icebreakers, Fillers y Warmers: actividades breves para la clase de inglés

    Directory of Open Access Journals (Sweden)

    Ramiro DURÁN MARTÍNEZ

    2009-11-01

    Full Text Available RESUMEN: En el siguiente artículo vamos a presentar diversos tipos de ejercicios de carácter breve que hemos utilizado en la clase de inglés con el objetivo de facilitar a los alumnos la práctica de la destreza oral. Estas actividades tienen distintos nombres dependiendo de la función que desempeñen: icebreakers, fillers y warmers. Se denominan icebreakers los ejercicios diseñados para romper la tensión que normalmente rodea las primeras sesiones de cualquier nueva actividad, como, por ejemplo, la primera clase de un curso de inglés. Cuando se habla de fillers se enfatiza su función comodín: tareas independientes que normalmente sirven para completar los últimos minutos del horario establecido para la clase de idiomas. El término warmer se aplica a las actividades que se llevan a cabo después de un período vacacional con el propósito de favorecer el reencuentro del alumno con el idioma que está estudiando. El principal objetivo de estos ejercicios es el desarrollo de la capacidad de los alumnos para expresarse de forma oral utilizando la lengua inglesa, concentrándose más en la práctica de la fluidez (fluency que en la precisión (accuracy. Por otra parte, sirven para favorecer la creación de vínculos de unión entre un grupo de estudiantes.ABSTRACT: In this paper, we are going to present a number of short activities that have been used in the English class in order to give students extra speaking practice. These activities were given different names depending on the role they play in the class: icebreakers, fillers and warmers. Icebreakers are fluency practice exercises produced to defuse the tension that the first sessions of every new activity imply: i.e. the first lesson of English. When talking about fillers, we refer to short independent activities that are used when the projected exercises have taken less time than expected. Warmers are also fluency practice activities devised to put students back in touch with the

  14. LAMP using a disposable pocket warmer for anthrax detection, a highly mobile and reliable method for anti-bioterrorism.

    Science.gov (United States)

    Hatano, Ben; Maki, Takayuki; Obara, Takeyuki; Fukumoto, Hitomi; Hagisawa, Kohsuke; Matsushita, Yoshitaro; Okutani, Akiko; Bazartseren, Boldbaastar; Inoue, Satoshi; Sata, Tetsutaro; Katano, Harutaka

    2010-01-01

    A quick, reliable detection system is necessary to deal with bioterrorism. Loop-mediated isothermal amplification (LAMP) is a DNA amplification method that can amplify specific DNA fragments in isothermal conditions. We developed a new highly mobile and practical LAMP anthrax detection system that uses a disposable pocket warmer without the need for electricity (pocket-warmer LAMP). In our tests, the detection limit of the pocket-warmer LAMP was 1,000 copies of Bacillus anthracis pag and capB gene fragments per tube. The pocket-warmer LAMP also detected B. anthracis genes from DNA extracted from 0.1 volume of a B. anthracis colony. The lower detection limit of the pocket-warmer LAMP was not significantly different from that of a conventional LAMP using a heat block, and was not changed under cold (4 degrees C) or warm (37 degrees C) conditions in a Styrofoam box. The pocket-warmer LAMP could be useful against bioterrorism, and as a sensitive, reliable detection tool in areas with undependable electricity infrastructures.

  15. Impacts of Vertical Structure of Convection on Tropical Circulation in a Warmer Climate

    Science.gov (United States)

    Chen, C. A.; Chou, C.

    2014-12-01

    The atmosphere becomes warmer and more humid under global warming, while changes in precipitation show a large discrepancy on a regional scale. Changes in regional precipitation are usually associated with changes in tropical circulation. Stronger (weaker) upward motion enhances (reduces) precipitation amount and intensity, in addition to the effect of enhanced water vapor. In a more detailed analysis, however, changes in atmospheric vertical motion can be either strengthened or weakened, even within convective areas with positive rainfall anomalies. To understand the diverse responses of changes in tropical circulation in a warmer climate as well as the associated mechanism, atmospheric stability and the impact of the vertical structure of convection on tropical circulation are investigated in 32 coupled global climate models from CMIP3 and CMIP5. The study regions are convective areas with positive precipitation anomalies. Under global warming, an upward shift structure of vertical velocity is observed in all model simulations, which implies a deepening of convection and a more stable atmosphere. Areas with enhanced (weakened) ascending motion, the climatological bottom-heavy (top-heavy) structure of vertical velocity tends to import more (less) moist static energy to counteract the stabilization due to the effect of deepened convection, and then the ascending motion is strengthened (weakened). The bottom-heavy-like structure is dominated by shallow convection, while the top-heavy-like structure is usually associated with deep convection. In other words, shallow convection tends to strengthen tropical circulation and enhance upward motion in future climate.

  16. Mechanisms for Amplified Central European Summer Precipitation Extremes in a Warmer Mediterranean Climate

    Science.gov (United States)

    Volosciuk, Claudia; Maraun, Douglas; Semenov, Vladimir; Tilinina, Natalia; Latif, Mojib

    2015-04-01

    Central European climate is influenced by the Mediterranean Sea, where a strong increase in sea surface temperature (SST) has been observed during the last four decades. One example of extreme weather events are cyclones following the "Vb" pathway. These cyclones are generated over the Mediterranean Sea, travel northeastwards around the Alps and then hit central European countries. These cyclones carry large amounts of moisture and cause extreme precipitation, and subsequently flooding, particularly in summer. To investigate the mechanisms causing increased summer extreme precipitation due to increased Mediterranean SST in Europe, we analyze a series of simulations with the atmospheric general circulation model ECHAM5. In the control run, we forced the model with the 1970-1999 SST climatology. In an additional run, we replaced the Mediterranean and Black Sea SST forcing with the climatology of the warmer 2000-2012 period. ECHAM5 was run at high horizontal resolution (T159) and integrated for 40 years in each experiment. 20-season return levels were derived as a measure of extreme precipitation for daily precipitation in JJA (June - August). These return levels are estimated as quantiles of a stationary generalized Pareto distribution, based on exceedances of the 95th precipitation percentile. We have shown in a previous contribution that precipitation return levels in JJA increase along the Vb cyclone track although the number of Vb cyclones does not increase. Here we discuss the mechanisms responsible for this increase. Due to the warmer climate in the Mediterranean region, climatological mean evaporation and precipitable water in the atmosphere are increased. On extreme days, composites show an even further increase in precipitable water over the central European region. On these extreme days, a higher sea level pressure gradient between central Europe and the Atlantic causes enhanced cyclonic flow that transports more moisture from the Mediterranean region to

  17. Women are Warmer but No Less Assertive than Men: Gender and Language on Facebook

    Science.gov (United States)

    Park, Gregory; Schwartz, H. Andrew; Kern, Margaret L.; Eichstaedt, Johannes C.; Kosinski, Michael; Stillwell, David; Ungar, Lyle H.; Seligman, Martin E. P.

    2016-01-01

    Using a large social media dataset and open-vocabulary methods from computational linguistics, we explored differences in language use across gender, affiliation, and assertiveness. In Study 1, we analyzed topics (groups of semantically similar words) across 10 million messages from over 52,000 Facebook users. Most language differed little across gender. However, topics most associated with self-identified female participants included friends, family, and social life, whereas topics most associated with self-identified male participants included swearing, anger, discussion of objects instead of people, and the use of argumentative language. In Study 2, we plotted male- and female-linked language topics along two interpersonal dimensions prevalent in gender research: affiliation and assertiveness. In a sample of over 15,000 Facebook users, we found substantial gender differences in the use of affiliative language and slight differences in assertive language. Language used more by self-identified females was interpersonally warmer, more compassionate, polite, and—contrary to previous findings—slightly more assertive in their language use, whereas language used more by self-identified males was colder, more hostile, and impersonal. Computational linguistic analysis combined with methods to automatically label topics offer means for testing psychological theories unobtrusively at large scale. PMID:27223607

  18. The Madden-Julian Oscillation and its Teleconnections in a Warmer World

    Science.gov (United States)

    Maloney, Eric; Wolding, Brandon; Henderson, Stephanie

    2017-04-01

    Two simulations of the Superparameterized Community Earth System Model (SP-CESM) are examined, one with pre-industrial (PI) levels of CO2 and one where CO2 levels have been quadrupled (4xCO2). While MJO convective variability increases considerably in the 4xCO2 simulation, the dynamical response to this convective variability decreases. Increased MJO convective variability is shown to be a robust response to the steepening vertical moisture gradient, consistent with the findings of previous studies. The decreased dynamical response to MJO convective variability is shown to be a consequence of increased static stability, which allows weaker variations in large-scale vertical velocity to produce sufficient adiabatic cooling to balance variations in MJO convective heating. This weakened dynamical response results in a considerable reduction of the MJO's ability to influence the extratropics, which is closely tied to the strength of its associated divergence. A linear baroclinic model is used to verify the impact of increased static stability on the extratropical circulation in a warmer climate. Results of this study suggest that, while MJO convective variability may increase in a warming climate, the MJO's role in bridging weather and climate in the extratropics may not.

  19. Rapid evolution of parasite resistance in a warmer environment: insights from a large scale field experiment.

    Science.gov (United States)

    Mateos-Gonzalez, Fernando; Sundström, L Fredrik; Schmid, Marian; Björklund, Mats

    2015-01-01

    Global climate change is expected to have major effects on host-parasite dynamics, with potentially enormous consequences for entire ecosystems. To develop an accurate prognostic framework, theoretical models must be supported by empirical research. We investigated potential changes in host-parasite dynamics between a fish parasite, the eyefluke Diplostomum baeri, and an intermediate host, the European perch Perca fluviatilis, in a large-scale semi-enclosed area in the Baltic Sea, the Biotest Lake, which since 1980 receives heated water from a nuclear power plant. Two sample screenings, in two consecutive years, showed that fish from the warmer Biotest Lake were now less parasitized than fish from the Baltic Sea. These results are contrasting previous screenings performed six years after the temperature change, which showed the inverse situation. An experimental infection, by which perch from both populations were exposed to D. baeri from the Baltic Sea, revealed that perch from the Baltic Sea were successfully infected, while Biotest fish were not. These findings suggest that the elevated temperature may have resulted, among other outcomes, in an extremely rapid evolutionary change through which fish from the experimental Biotest Lake have gained resistance to the parasite. Our results confirm the need to account for both rapid evolutionary adaptation and biotic interactions in predictive models, and highlight the importance of empirical research in order to validate future projections.

  20. Impact of warmer weather on electricity sector emissions due to building energy use

    Science.gov (United States)

    Meier, Paul; Holloway, Tracey; Patz, Jonathan; Harkey, Monica; Ahl, Doug; Abel, David; Schuetter, Scott; Hackel, Scott

    2017-06-01

    Most US energy consumption occurs in buildings, with cooling demands anticipated to increase net building electricity use under warmer conditions. The electricity generation units that respond to this demand are major contributors to sulfur dioxide (SO2) and nitrogen oxides (NOx), both of which have direct impacts on public health, and contribute to the formation of secondary pollutants including ozone and fine particulate matter. This study quantifies temperature-driven changes in power plant emissions due to increased use of building air conditioning. We compare an ambient temperature baseline for the Eastern US to a model-calculated mid-century scenario with summer-average temperature increases ranging from 1 C to 5 C across the domain. We find a 7% increase in summer electricity demand and a 32% increase in non-coincident peak demand. Power sector modeling, assuming only limited changes to current generation resources, calculated a 16% increase in emissions of NOx and an 18% increase in emissions of SO2. There is a high level of regional variance in the response of building energy use to climate, and the response of emissions to associated demand. The East North Central census region exhibited the greatest sensitivity of energy demand and associated emissions to climate.

  1. Intense precipitation extremes in a warmer climate: results from CMIP5 models

    Science.gov (United States)

    scoccimarro, enrico; gualdi, silvio; bellucci, alessio; zampieri, matteo; navarra, antonio

    2013-04-01

    In this work the authors investigate possible changes in the intensity of extreme precipitation events under a warmer climate, using the results of a set of 20 climate models taking part to the Coupled Model Intercomparison Project phase 5 effort (CMIP5). Future changes are evaluated as the epoch difference between the last four decades of the 21st and the 20th Century assuming the Representative Concentration Pathway RCP8.5 scenario. As a measure of the intensity associated with extreme precipitation events, we use the difference between the 99th and the 90th percentiles. Despite a slight tendency to underestimate the observed extreme precipitation intensity, the considered CMIP5 models well represent the observed patterns during both summer and winter seasons for the 1997-2005 period. Future changes in average precipitation are consistent with previous findings based on CMIP3 models. CMIP5 models show a projected increase for the end of the twenty-first century of the intensity of the extreme precipitations, particularly pronounced over India, South East Asia, Indonesia and Central Africa during boreal summer, as well as over South America and the southern Africa during boreal winter. These changes are consistent with a strong increase of the column integrated water content availability over the afore mentioned regions.

  2. Women are Warmer but No Less Assertive than Men: Gender and Language on Facebook.

    Directory of Open Access Journals (Sweden)

    Gregory Park

    Full Text Available Using a large social media dataset and open-vocabulary methods from computational linguistics, we explored differences in language use across gender, affiliation, and assertiveness. In Study 1, we analyzed topics (groups of semantically similar words across 10 million messages from over 52,000 Facebook users. Most language differed little across gender. However, topics most associated with self-identified female participants included friends, family, and social life, whereas topics most associated with self-identified male participants included swearing, anger, discussion of objects instead of people, and the use of argumentative language. In Study 2, we plotted male- and female-linked language topics along two interpersonal dimensions prevalent in gender research: affiliation and assertiveness. In a sample of over 15,000 Facebook users, we found substantial gender differences in the use of affiliative language and slight differences in assertive language. Language used more by self-identified females was interpersonally warmer, more compassionate, polite, and-contrary to previous findings-slightly more assertive in their language use, whereas language used more by self-identified males was colder, more hostile, and impersonal. Computational linguistic analysis combined with methods to automatically label topics offer means for testing psychological theories unobtrusively at large scale.

  3. Will a warmer and wetter future cause extinction of native Hawaiian forest birds?

    Science.gov (United States)

    Liao, Wei; Elison Timm, Oliver; Zhang, Chunxi; Atkinson, Carter T; LaPointe, Dennis A; Samuel, Michael D

    2015-12-01

    Isolation of the Hawaiian archipelago produced a highly endemic and unique avifauna. Avian malaria (Plasmodium relictum), an introduced mosquito-borne pathogen, is a primary cause of extinctions and declines of these endemic honeycreepers. Our research assesses how global climate change will affect future malaria risk and native bird populations. We used an epidemiological model to evaluate future bird-mosquito-malaria dynamics in response to alternative climate projections from the Coupled Model Intercomparison Project. Climate changes during the second half of the century accelerate malaria transmission and cause a dramatic decline in bird abundance. Different temperature and precipitation patterns produce divergent trajectories where native birds persist with low malaria infection under a warmer and dryer projection (RCP4.5), but suffer high malaria infection and severe reductions under hot and dry (RCP8.5) or warm and wet (A1B) futures. We conclude that future global climate change will cause significant decreases in the abundance and diversity of remaining Hawaiian bird communities. Because these effects appear unlikely before mid-century, natural resource managers have time to implement conservation strategies to protect this unique avifauna from further decimation. Similar climatic drivers for avian and human malaria suggest that mitigation strategies for Hawai'i have broad application to human health.

  4. Cold Surge Activity Over the Gulf of Mexico in a Warmer Climate

    Directory of Open Access Journals (Sweden)

    Edgar Perez Perez

    2014-08-01

    Full Text Available Cold surges are a dominant feature of midlatitude tropical interaction. During the North Hemisphere (NH winter, midlatitude waves propagating from the Rocky Mountains into the Gulf of Mexico result in cold surges, also known as Nortes or Tehuantepecers, associated with severe weather over the southern part of Mexico. The magnitude of their intense surface winds, precipitation and drops in surface temperature depends on the characteristics of the midlatitude wave propagating into the tropics. The high spatial resolution (20km X 20km version of the TL959L60-AGC Model of the Meteorological Research Institute of Japan is used to examine changes in cold surge activity under the A1B greenhouse gas emission scenario for the 2080 - 2099 period. The model realistically reproduces the spatial and temporal characteristics of cold surges for the 1980 - 1989 control period. The effect of changes in baroclinicity, static stability and mean flow over North America suggest that in a warmer climate, increased cold surge activity over the Gulf of Mexico would occur. However, these systems would have shorter wavelength (higher phase speeds and shorter lifespans that could reduce the total amount of winter precipitation. The increased frequency of cold surges over the Gulf of Mexico would be a consequence of weaker baroclinicity and static stability in the lower troposphere over the cold surge genesis region, along with more dominant westerly winds, resulting from ENSO-like conditions in the atmospheric circulations over North America.

  5. Women are Warmer but No Less Assertive than Men: Gender and Language on Facebook.

    Science.gov (United States)

    Park, Gregory; Yaden, David Bryce; Schwartz, H Andrew; Kern, Margaret L; Eichstaedt, Johannes C; Kosinski, Michael; Stillwell, David; Ungar, Lyle H; Seligman, Martin E P

    2016-01-01

    Using a large social media dataset and open-vocabulary methods from computational linguistics, we explored differences in language use across gender, affiliation, and assertiveness. In Study 1, we analyzed topics (groups of semantically similar words) across 10 million messages from over 52,000 Facebook users. Most language differed little across gender. However, topics most associated with self-identified female participants included friends, family, and social life, whereas topics most associated with self-identified male participants included swearing, anger, discussion of objects instead of people, and the use of argumentative language. In Study 2, we plotted male- and female-linked language topics along two interpersonal dimensions prevalent in gender research: affiliation and assertiveness. In a sample of over 15,000 Facebook users, we found substantial gender differences in the use of affiliative language and slight differences in assertive language. Language used more by self-identified females was interpersonally warmer, more compassionate, polite, and-contrary to previous findings-slightly more assertive in their language use, whereas language used more by self-identified males was colder, more hostile, and impersonal. Computational linguistic analysis combined with methods to automatically label topics offer means for testing psychological theories unobtrusively at large scale.

  6. Will a warmer and wetter future cause extinction of native Hawaiian forest birds?

    Science.gov (United States)

    Liao, Wei; Timm, Oliver Elison; Zhang, Chunxi; Atkinson, Carter T.; LaPointe, Dennis; Samuel, Michael D.

    2015-01-01

    Isolation of the Hawaiian archipelago produced a highly endemic and unique avifauna. Avian malaria (Plasmodium relictum), an introduced mosquito-borne pathogen, is a primary cause of extinctions and declines of these endemic honeycreepers. Our research assesses how global climate change will affect future malaria risk and native bird populations. We used an epidemiological model to evaluate future bird-mosquito-malaria dynamics in response to alternative climate projections from the Coupled Model Intercomparison Project (CMIP). Climate changes during the second half of the century accelerate malaria transmission and cause a dramatic decline in bird abundance. Different temperature and precipitation patterns produce divergent trajectories where native birds persist with low malaria infection under a warmer and dryer projection (RCP4.5), but suffer high malaria infection and severe reductions under hot and dry (RCP8.5) or warm and wet (A1B) futures. We conclude that future global climate change will cause significant decreases in the abundance and diversity of remaining Hawaiian bird communities. Because these effects appear unlikely before mid-century, natural resource managers have time to implement conservation strategies to protect this unique avifauna from further decimation. Similar climatic drivers for avian and human malaria suggest that mitigation strategies for Hawai'i have broad application to human health.

  7. The Effect of Insulating Blood Warmer Output Tubing on the Temperature of Packed Red Blood Cells at Low Flow Rates

    Science.gov (United States)

    1989-01-01

    as the most effective method to minimize the detrimental effects of hypothermia (Boyan & Howland, 1962; Aldrete , 1985; Fried, Satiani, & Zeeb, 1986...rates result in an increased heat loss in both non-insulated and insulated blood warmer output tubing. 62 References 63 References Aldrete , J. A. (1985

  8. Warmer weather linked to tick attack and emergence of severe rickettsioses.

    Directory of Open Access Journals (Sweden)

    Philippe Parola

    Full Text Available The impact of climate on the vector behaviour of the worldwide dog tick Rhipicephalus sanguineus is a cause of concern. This tick is a vector for life-threatening organisms including Rickettsia rickettsii, the agent of Rocky Mountain spotted fever, R. conorii, the agent of Mediterranean spotted fever, and the ubiquitous emerging pathogen R. massiliae. A focus of spotted fever was investigated in France in May 2007. Blood and tissue samples from two patients were tested. An entomological survey was organised with the study of climatic conditions. An experimental model was designed to test the affinity of Rh. sanguineus for biting humans in variable temperature conditions. Serological and/or molecular tools confirmed that one patient was infected by R. conorii, whereas the other was infected by R. massiliae. Dense populations of Rh. sanguineus were found. They were infected with new genotypes of clonal populations of either R. conorii (24/133; 18% or R. massiliae (13/133; 10%. April 2007 was the warmest since 1950, with summer-like temperatures. We show herein that the human affinity of Rh. sanguineus was increased in warmer temperatures. In addition to the originality of theses cases (ophthalmic involvements, the second reported case of R. massiliae infection, we provide evidence that this cluster of cases was related to a warming-mediated increase in the aggressiveness of Rh. sanguineus, leading to increased human attacks. From a global perspective, we predict that as a result of globalisation and warming, more pathogens transmitted by the brown dog tick may emerge in the future.

  9. Stronger sexual selection in warmer waters: the case of a sex role reversed pipefish.

    Directory of Open Access Journals (Sweden)

    Nuno M Monteiro

    Full Text Available In order to answer broader questions about sexual selection, one needs to measure selection on a wide array of phenotypic traits, simultaneously through space and time. Nevertheless, studies that simultaneously address temporal and spatial variation in reproduction are scarce. Here, we aimed to investigate the reproductive dynamics of a cold-water pipefish simultaneously through time (encompassing variation within each breeding cycle and as individuals grow and space (by contrasting populations experiencing distinct water temperature regimes in order to test hypothesized differences in sexual selection. Even though the sampled populations inhabited locations with very different water temperature regimes, they exhibited considerable similarities in reproductive parameters. The most striking was the existence of a well-defined substructure in reproductive activity, where larger individuals reproduce for longer periods, which seemed dependent on a high temperature threshold for breeding rather than on the low temperatures that vary heavily according to latitude. Furthermore, the perceived disparities among populations, such as size at first reproduction, female reproductive investment, or degree of sexual size dimorphism, seemed dependent on the interplay between seawater temperature and the operational sex ratio (OSR. Contrary to our expectations of an enhanced opportunity for sexual selection in the north, we found the opposite: higher female reproductive investment coupled with increased sexual size dimorphism in warmer waters, implying that a prolonged breeding season does not necessarily translate into reduced sexual selection pressure. In fact, if the limited sex has the ability to reproduce either continuously or recurrently during the entire breeding season, an increased opportunity for sexual selection might arise from the need to compete for available partners under strongly biased OSRs across protracted breeding seasons. A more general

  10. Tropical-Extratropical Interactions and Intrasasonal Oscillations in the Indian Monsoon System in a Warmer Planet

    Science.gov (United States)

    Carvalho, L. V.; Jones, C.; Cannon, F.; Norris, J.

    2015-12-01

    The India summer monsoon (ISM) experiences long periods of wet and dry conditions frequently associated with floods and long dry spells. These events are largely governed by northward propagating boreal summer monsoon intraseasonal oscillations (MISO). Here we investigate intraseasonal variability of the ISM in the climate of the 20th century using the Climate Forecast System Reanalysis (1979-2013) and examine future scenarios of climate change using models of the Coupled Model Intercomparison Project Phase-5 project. ISM is characterized with a large-scale index obtained by performing combined EOF analysis of precipitation, low level circulation, specific humidity and temperature. This index realistically defines the monsoon's onset and withdrawal, is well correlated with seasonal precipitation in India and exhibits variance on intraseasonal timescales that are related to MISO and extreme wet and dry conditions in India. With similar approach we investigate the skill of the CMIP5 models in realistically simulating MISO in the 'historic' run (1951-2005) and examine projected changes in the amplitude and persistence these events in the high-emission representative concentration pathway 8.5 (RCP8.5) (2006-2100). MISO is well characterized in CMIP5 models that indicate significant increase in the intensity and frequency of extremely dry and wet conditions affecting India by 2050. We show that the main mechanism driving MISO in CMIP5 models are linked to the propagation of extratropical wave trains and interactions with the tropics. In a warmer planet, the increase in polar temperatures weakens the tropical-extratropical temperature gradient and decreases the intensity of the upper tropospheric jet. These changes in the jet and in the baroclinic structure of the atmosphere result in enhanced extratropical wave activity and more extreme events. We use a wave tracking algorithm to demonstrate these differences and explore physical and dynamical mechanisms underlying

  11. Severe Autumn storms in future Western Europe with a warmer Atlantic Ocean

    Science.gov (United States)

    Baatsen, Michiel; Haarsma, Reindert J.; Van Delden, Aarnout J.; de Vries, Hylke

    2015-08-01

    Simulations with a very high resolution (~25 km) global climate model indicate that more severe Autumn storms will impact Europe in a warmer future climate. The observed increase is mainly attributed to storms with a tropical origin, especially in the later part of the twentyfirst century. As their genesis region expands, tropical cyclones become more intense and their chances of reaching Europe increase. This paper investigates the properties and evolution of such storms and clarifies the future changes. The studied tropical cyclones feature a typical evolution of tropical development, extratropical transition and a re-intensification. A reduction of the transit area between regions of tropical and extratropical cyclogenesis increases the probability of re-intensification. Many of the modelled storms exhibit hybrid properties in a considerable part of their life cycle during which they exhibit the hazards of both tropical and extratropical systems. In addition to tropical cyclones, other systems such as cold core extratropical storms mainly originating over the Gulf Stream region also increasingly impact Western Europe. Despite their different history, all of the studied storms have one striking similarity: they form a warm seclusion. The structure, intensity and frequency of storms in the present climate are compared to observations using the MERRA and IBTrACS datasets. Damaging winds associated with the occurrence of a sting jet are observed in a large fraction of the cyclones during their final stage. Baroclinic instability is of great importance for the (re-)intensification of the storms. Furthermore, so-called atmospheric rivers providing tropical air prove to be vital for the intensification through diabatic heating and will increase considerably in strength in the future, as will the associated flooding risks.

  12. Reproductive trade-offs may moderate the impact of Gyrodactylus salaris in warmer climates.

    Directory of Open Access Journals (Sweden)

    Scott J Denholm

    Full Text Available Gyrodactylus salaris is a notifiable freshwater ectoparasite of salmonids. Its primary host is Atlantic salmon (Salmo salar, upon which infections can cause death, and have led to massive declines in salmon numbers in Norway, where the parasite is widespread. Different strains of S. salar vary in their susceptibility, with Atlantic strains (such as those found in Norway exhibiting no resistance to the parasite, and Baltic strains demonstrating an innate resistance sufficient to regulate parasite numbers on the host causing it to either die out or persist at a low level. In this study, Leslie matrix and compartmental models were used to generate data that demonstrated the population growth of G. salaris on an individual host is dependent on the total number of offspring per parasite, its longevity and the timing of its births. The data demonstrated that the key factor determining the rate of G. salaris population growth is the time at which the parasite first gives birth, with rapid birth rate giving rise to large population size. Furthermore, it was shown that though the parasite can give birth up to four times, only two births are required for the population to persist as long as the first birth occurs before a parasite is three days old. As temperature is known to influence the timing of the parasite's first birth, greater impact may be predicted if introduced to countries with warmer climates than Norway, such as the UK and Ireland which are currently recognised to be free of G. salaris. However, the outputs from the models developed in this study suggest that temperature induced trade-offs between the total number of offspring the parasite gives birth to and the first birth timing may prevent increased population growth rates over those observed in Norway.

  13. Effects on zooplankton of a warmer ocean: Recent evidence from the Northeast Pacific

    Science.gov (United States)

    Mackas, David L.; Batten, Sonia; Trudel, Marc

    2007-10-01

    The consequences for pelagic communities of warming trends in mid and high latitude ocean regions could be substantial, but their magnitude and trajectory are not yet known. Environmental changes predicted by climate models (and beginning to be confirmed by observations) include warming and freshening of the upper ocean and reduction in the extent and duration of ice cover. One way to evaluate response scenarios is by comparing how “similar” zooplankton communities have differed among years and/or locations with differing temperature. The subarctic Pacific is a strong candidate for such comparisons, because the same mix of zooplankton species dominates over a wide range of temperature climatologies, and observations have spanned substantial temperature variability at interannual-to-decadal time scales. In this paper, we review and extend copepod abundance and phenology time series from net tow and Continuous Plankton Recorder surveys in the subarctic Northeast Pacific. The two strongest responses we have observed are latitudinal shifts in centers of abundance of many species (poleward under warm conditions), and changes in the life cycle timing of Neocalanus plumchrus in both oceanic and coastal regions (earlier by several weeks in warm years and at warmer locations). These zooplankton data, plus indices of higher trophic level responses such as reproduction, growth and survival of pelagic fish and seabirds, are all moderately-to-strongly intercorrelated (∣ r∣ = 0.25-0.8) with indices of local and basin-scale temperature anomalies. A principal components analysis of the normalized anomaly time series from 1979 to 2004 shows that a single “warm-and-low-productivity” vs. “cool-and-high-productivity” component axis accounts for over half of the variance/covariance. Prior to 1990, the scores for this component were negative (“cool” and “productive”) or near zero except positive in the El Niño years 1983 and 1987. The scores were strongly and

  14. Warmer and drier conditions and nitrogen fertilizer application altered methanotroph abundance and methane emissions in a vegetable soil.

    Science.gov (United States)

    Ran, Yu; Xie, Jianli; Xu, Xiaoya; Li, Yong; Liu, Yapeng; Zhang, Qichun; Li, Zheng; Xu, Jianming; Di, Hongjie

    2016-11-12

    Methane (CH4) is a potent greenhouse gas, and soil can both be a source and sink for atmospheric CH4. It is not clear how future climate change may affect soil CH4 emissions and related microbial communities. The aim of this study was to determine the interactive effects of a simulated warmer and drier climate scenarios and the application of different nitrogen (N) sources (urea and manure) on CH4 emissions and related microbial community abundance in a vegetable soil. Greenhouses were used to control simulated climate conditions which gave 2.99 °C warmer and 6.2% lower water content conditions. The field experiment was divided into two phases. At the beginning of phase II, half of the greenhouses were removed to study possible legacy effects of the simulated warmer and drier conditions. The responses in methanogen and methanotroph abundance to a simulated climate change scenario were determined using real-time PCR. The results showed that the simulated warmer and drier conditions in the greenhouses significantly decreased CH4 emissions largely due to the lower soil moisture content. For the same reason, CH4 emissions of treatments in phase I were much lower than the same treatments in phase II. The abundance of methanotrophs showed a more significant response than methanogens to the simulated climate change scenario, increasing under simulated drier conditions. Methanogenic community abundance remained low, except where manure was applied which provided a source of organic C that stimulated methanogen growth. Soil moisture content was a major driver for methanotroph abundance and strongly affected CH4 emissions. The application of N source decreased CH4 emissions probably because of increased methanotrophic activity. CH4 emissions were positively correlated to methanogenic abundance and negatively correlated to methanotrophic abundance. These results demonstrate that projected future climate change conditions can have a feedback impact on CH4 emissions from the

  15. The Potential Impacts of Warmer-Continent-Related Lower-Layer Equatorial Westerly Wind on Tropical Cyclone Initiation

    Institute of Scientific and Technical Information of China (English)

    YUAN Zhuojian; QIAN Yu-Kun; QI Jindian; WU Junjie

    2012-01-01

    Global climate models predict that the increasing Amazonian-deforestation rates cause rising temperatures (increases of 1.8℃ to 8℃ under different conditions) and Amazonian drying over the 21st century.Observations in the 20th century also show that over the warmer continent and the nearby western South Atlantic Ocean,the lower-layer equatorial westerly wind (LLEWW) strengthens with the initiation of tropical cyclones (TCs).The warmer-continent-related LLEWW can result from the Coriolis-force-induced deflection of the cross-equatorial flow (similar to the well-known heat-island effect on sea breeze) driven by the enhanced land-sea contrast between the warmer urbanized continents and relatively cold oceans.This study focuses on the processes relating the warmer-continent-related LLEWW to the TC initiation and demonstrates that the LLEWW embedded in trade easterlies can directly initiate TCs by creating cyclonic wind shears and forming the intertropical convergence zone.In addition to this direct effect,the LLEWW combined with the rotating Earth can boost additional updraft vapor over the high sea-surface temperature region (factor 1),facilitating a surface-to-midtroposphere moist layer (factor 2) and convective instability (factor 3) followed by diabatic processes.According to previous studies,the diabatic heating in a finite equatorial region also activates TCs (factor 4) on each side of the Equator with weak vertical shear (factor 5).Factors 1 5 are favorable conditions for the initiation of severe TCs.Statistical analyses show that the earliest signal of sustained LLEWW not only leads the earliest signal of sustained tropical depression by >3 days but also explains a higher percentage of total variance.

  16. Potential costs of acclimatization to a warmer climate: growth of a reef coral with heat tolerant vs. sensitive symbiont types.

    Science.gov (United States)

    Jones, Alison; Berkelmans, Ray

    2010-05-03

    One of the principle ways in which reef building corals are likely to cope with a warmer climate is by changing to more thermally tolerant endosymbiotic algae (zooxanthellae) genotypes. It is highly likely that hosting a more heat-tolerant algal genotype will be accompanied by tradeoffs in the physiology of the coral. To better understand one of these tradeoffs, growth was investigated in the Indo-Pacific reef-building coral Acropora millepora in both the laboratory and the field. In the Keppel Islands in the southern Great Barrier Reef this species naturally harbors nrDNA ITS1 thermally sensitive type C2 or thermally tolerant type D zooxanthellae of the genus Symbiodinium and can change dominant type following bleaching. We show that under controlled conditions, corals with type D symbionts grow 29% slower than those with type C2 symbionts. In the field, type D colonies grew 38% slower than C2 colonies. These results demonstrate the magnitude of trade-offs likely to be experienced by this species as they acclimatize to warmer conditions by changing to more thermally tolerant type D zooxanthellae. Irrespective of symbiont genotype, corals were affected to an even greater degree by the stress of a bleaching event which reduced growth by more than 50% for up to 18 months compared to pre-bleaching rates. The processes of symbiont change and acute thermal stress are likely to act in concert on coral growth as reefs acclimatize to more stressful warmer conditions, further compromising their regeneration capacity following climate change.

  17. Potential costs of acclimatization to a warmer climate: growth of a reef coral with heat tolerant vs. sensitive symbiont types.

    Directory of Open Access Journals (Sweden)

    Alison Jones

    Full Text Available One of the principle ways in which reef building corals are likely to cope with a warmer climate is by changing to more thermally tolerant endosymbiotic algae (zooxanthellae genotypes. It is highly likely that hosting a more heat-tolerant algal genotype will be accompanied by tradeoffs in the physiology of the coral. To better understand one of these tradeoffs, growth was investigated in the Indo-Pacific reef-building coral Acropora millepora in both the laboratory and the field. In the Keppel Islands in the southern Great Barrier Reef this species naturally harbors nrDNA ITS1 thermally sensitive type C2 or thermally tolerant type D zooxanthellae of the genus Symbiodinium and can change dominant type following bleaching. We show that under controlled conditions, corals with type D symbionts grow 29% slower than those with type C2 symbionts. In the field, type D colonies grew 38% slower than C2 colonies. These results demonstrate the magnitude of trade-offs likely to be experienced by this species as they acclimatize to warmer conditions by changing to more thermally tolerant type D zooxanthellae. Irrespective of symbiont genotype, corals were affected to an even greater degree by the stress of a bleaching event which reduced growth by more than 50% for up to 18 months compared to pre-bleaching rates. The processes of symbiont change and acute thermal stress are likely to act in concert on coral growth as reefs acclimatize to more stressful warmer conditions, further compromising their regeneration capacity following climate change.

  18. Changes of Warmer Winter and Winter Temperature over China During 1956-2005%1956-2005年中国暖冬和冬季温度变化

    Institute of Scientific and Technical Information of China (English)

    王凌; 张强; 陈峪

    2008-01-01

    Areasonable warmer winter index(IwwI)in the framework of the three equiprobability categories(i.e.warmer,normal and colder categories)is proposed based on the winter temperature data observed at 565 stations in China during 1956-2005,where IwwI is defined as the ratio of the station number of warmer category over the total number of stations.The results suggest that the trend of IwwI was consistent with that of the winter temperature on decadal time scale,and their rates of change were 10%/10 a and 0.4℃/10 a,respectively.It is found that only 13 warmer winter events in total were detected by IwwI over the past 50 years,and 85% of them occurred after 1986.

  19. Growth, condition factor, and bioenergetics modeling link warmer stream temperatures below a small dam to reduced performance of juvenile steelhead

    Science.gov (United States)

    Sauter, S.T.; Connolly, P.J.

    2010-01-01

    We investigated the growth and feeding performance of juvenile steelhead Oncorhynchus mykiss using field measures and bioenergetics modeling. Juvenile steelhead populations were sampled from mid-June through August 2004 at study sites upstream and downstream of Hemlock Dam. The growth and diet of juvenile steelhead were determined for a warm (summer) and subsequent (late summer) transitional period at each study site. Empirical data on the growth and diet of juvenile steelhead and mean daily temperatures were used in a bioenergetics model to estimate the proportion of maximum consumption achieved by juvenile steelhead by site and period. Modeled estimates of feeding performance were better for juvenile steelhead at the upstream compared to the downstream site during both periods. The median condition factor of juvenile steelhead did not change over the summer at the upstream site, but showed a significant decline over time at the downstream site. A negative trend in median condition factor at the downstream site supported bioenergetics modeling results that suggested the warmer stream temperatures had a negative impact on juvenile steelhead. Bioenergetics modeling predicted a lower feeding performance for juvenile steelhead rearing downstream compared to upstream of Hemlock Dam although food availability appeared to be limited at both study sites during the warm period. Warmer water temperatures, greater diel variation, and change in diel pattern likely led to the reduced feeding performance and reduced growth, which could have affected the overall survival of juvenile steelhead downstream of Hemlock Dam. ?? 2010 by the Northwest Scientific Association.

  20. A warmer ambient temperature increases the passage of interleukin-1β into the brains of old rats

    Science.gov (United States)

    Buchanan, Jessica B.; Peloso, Elizabeth; Satinoff, Evelyn

    2008-01-01

    We have demonstrated that after intraperitoneal lipopolysaccharide (LPS) injection, old rats mount fevers similar to those of young rats at an ambient temperature (Ta) of 31°C, but not at 21°C. The same is true for intraperitoneal or intravenous IL-1β administration. The underlying mechanism responsible for blunted fever in old rats may be a deficiency in communication between the periphery and the brain. Possibly, peripheral cytokine actions are altered in old rats, such that the signal that reaches the brain is diminished. Here, we hypothesized that at standard laboratory temperatures, not enough IL-1β is reaching the brain for fever to occur and that a warmer Ta would increase the influx of IL-1β into the brain, enabling old rats to generate fever. Young (3–5 mo) and old (23–29 mo) Long-Evans rats were maintained for 3 days at either Ta 21 or 31°C prior to intravenous injection with radiolabeled IL-1β to measure passage across the blood-brain barrier. Young rats showed similar influx of IL-1β into the brain at the two Tas, but old rats showed significant influx only at the warmer Ta. These data suggest that the lack of fever at a cool Ta may be due to a reduced influx of IL-1β into the brain. PMID:18448612

  1. Building when the climate gets warmer; Bauen, wenn das Klima waermer wird - Schlussbericht

    Energy Technology Data Exchange (ETDEWEB)

    Brunner, C. U. [Energieplaner, CUB Architektur Energie Umwelt, Zuerich (Switzerland); Steinemann, U. [Ingenieurbuero Urs Steinemann, Wollerau (Switzerland); Nipkow, J. [Arena, Arbeitsgemeinschaft Energie-Alternativen, Zuerich (Switzerland)

    2007-07-01

    This final report for the Swiss Federal Office of Energy (SFOE), takes a look at how the building process will have to take account of climate change with higher summer temperatures in Switzerland. The authors consider the situation as being in strong contrast to the past in Switzerland, when attention was devoted to energy demand in buildings during the winter. Today there is a new focus with the anticipation of increasingly frequent, extended hot spells in summer. The goal of this investigation is to analyse and present economic measures to assure a high level of summer comfort with a reduced demand for electricity under these changing conditions. Strategies with respect to construction, technology and operation are addressed. The current spread of technically questionable and inefficient room air conditioning units in residential and commercial buildings is considered as being strongly reminiscent of a dangerous, analogous case in the past, when small electric heaters became widespread. A largely untapped potential exists for increasing the efficiency of air conditioning and chiller technologies for both central systems and room units by the careful use of small temperature differences. Several new and unconventional solution paths are discussed, including high-efficiency room air conditioners, solar cooling equipment, balanced mechanical ventilation, phase-change materials, thermal storage, etc., all aimed at reducing electricity consumption. The expected additional electricity demand of around 1.9 TWh annually for ventilation and air conditioning is commented on.

  2. Technology.

    Science.gov (United States)

    Online-Offline, 1998

    1998-01-01

    Focuses on technology, on advances in such areas as aeronautics, electronics, physics, the space sciences, as well as computers and the attendant progress in medicine, robotics, and artificial intelligence. Describes educational resources for elementary and middle school students, including Web sites, CD-ROMs and software, videotapes, books,…

  3. Designing urban spaces and buildings to improve sustainability and quality of life in a warmer world

    Energy Technology Data Exchange (ETDEWEB)

    Smith, Claire; Levermore, Geoff [Built Environment Research Group, University of Manchester, PO Box 88, Sackville Street, Manchester M60 1QD (United Kingdom)

    2008-12-15

    It is in cities that the negative impacts of a warming climate will be felt most strongly. The summer time comfort and well-being of the urban population will become increasingly compromised under future scenarios for climate change and urbanisation. In contrast to rural areas, where night-time relief from high daytime temperatures occurs as heat is lost to the sky, the city environment stores and traps heat and offers little respite from high temperatures. This urban heat island effect is responsible for temperature differences of up to 7 C between cities and the country in the UK. We already have experience of the potential hazards of these higher temperatures. The majority of heat-related fatalities during the summer of 2003 were in urban areas. This means that the cooling of the urban environment is a high priority for urban planners and designers. Proven ways of doing this include altering the urban microclimate by modifying its heat absorption and emission, for example through urban greening, the use of high-reflectivity materials, and by increasing openness to allow cooling winds. Buildings themselves can also deliver improved comfort and higher levels of sustainability by taking advantage of exemplary facade, glazing and ventilation designs. In addition, changed behaviour by building occupants can help keep urban areas cool. The technology to reduce the future vulnerability of city dwellers to thermal discomfort is already largely in existence. But there is a need for complementary policy and planning commitments to manage its implementation, especially in existing buildings and urban areas. (author)

  4. The effect of the pathway to a two degrees warmer world on the regional temperature change of Europe

    Directory of Open Access Journals (Sweden)

    Cathrine Fox Maule

    2017-08-01

    Full Text Available The purpose of this study is to investigate if the pathway to reach a 2 degree warmer world influences the regional climate in Europe at the time of 2 degrees of global warming above the pre-industrial level. We have investigated this using climate change data from ensembles of both Global Climate Models and Regional Climate Models. We compare the change of regional temperature in Europe to the global temperature change for different emission scenarios, following the IPCC Representative Concentration Pathways (RCP, to see if the pathway has any influence. We find that there is a small but significant difference in the regional temperature change, but the effect is small compared to internal variability on the timescales involved in reaching +2 degrees for the investigated emission scenarios. From an adaptation point of view, reaching +2 degrees as slowly as possible will obviously allow for a longer time period to implement adaptation measures to mitigate the effect of climate change.

  5. Subtropical Low Cloud Response to a Warmer Climate in an Superparameterized Climate Model: Part I. Regime Sorting and Physical Mechanisms

    Directory of Open Access Journals (Sweden)

    Peter N Blossey

    2009-07-01

    Full Text Available The subtropical low cloud response to a climate with SST uniformly warmed by 2 K is analyzed in the SP- CAM superparameterized climate model, in which each grid column is replaced by a two-dimensional cloud-resolving model (CRM. Intriguingly, SP-CAM shows substantial low cloud increases over the subtropical oceans in the warmer climate. The paper aims to understand the mechanism for these increases. The subtropical low cloud increase is analyzed by sorting grid-column months of the climate model into composite cloud regimes using percentile ranges of lower tropospheric stability (LTS. LTS is observed to be well correlated to subtropical low cloud amount and boundary layer vertical structure. The low cloud increase in SP-CAM is attributed to boundary-layer destabilization due to increased clear-sky radiative cooling in the warmer climate. This drives more shallow cumulus convection and a moister boundary layer, inducing cloud increases and further increasing the radiative cooling. The boundary layer depth does not change substantially, due to compensation between increased radiative cooling (which promotes more turbulent mixing and boundary-layer deepening and slight strengthening of the boundary-layer top inversion (which inhibits turbulent entrainment and promotes a shallower boundary layer. The widespread changes in low clouds do not appear to be driven by changes in mean subsidence.
    In a companion paper we use column-mode CRM simulations based on LTS-composite profiles to further study the low cloud response mechanisms and to explore the sensitivity of low cloud response to grid resolution in SP-CAM.

  6. Technology

    Directory of Open Access Journals (Sweden)

    Xu Jing

    2016-01-01

    Full Text Available The traditional answer card reading method using OMR (Optical Mark Reader, most commonly, OMR special card special use, less versatile, high cost, aiming at the existing problems proposed a method based on pattern recognition of the answer card identification method. Using the method based on Line Segment Detector to detect the tilt of the image, the existence of tilt image rotation correction, and eventually achieve positioning and detection of answers to the answer sheet .Pattern recognition technology for automatic reading, high accuracy, detect faster

  7. Colder or Warmer?

    Institute of Scientific and Technical Information of China (English)

    Wanzy

    2010-01-01

    After the record heat wave this summer,some forecasters said this winter could be the coldest one in the last 1,000 years,which also would influence China and some other countries. Extremely cold weather in winter,of course,the most convenient and easy method to keep warm is to wear thick warm

  8. Warmer, deeper, and greener mixed layers in the North Atlantic subpolar gyre over the last 50 years.

    Science.gov (United States)

    Martinez, Elodie; Raitsos, Dionysios E; Antoine, David

    2016-02-01

    Shifts in global climate resonate in plankton dynamics, biogeochemical cycles, and marine food webs. We studied these linkages in the North Atlantic subpolar gyre (NASG), which hosts extensive phytoplankton blooms. We show that phytoplankton abundance increased since the 1960s in parallel to a deepening of the mixed layer and a strengthening of winds and heat losses from the ocean, as driven by the low frequency of the North Atlantic Oscillation (NAO). In parallel to these bottom-up processes, the top-down control of phytoplankton by copepods decreased over the same time period in the western NASG, following sea surface temperature changes typical of the Atlantic Multi-decadal Oscillation (AMO). While previous studies have hypothesized that climate-driven warming would facilitate seasonal stratification of surface waters and long-term phytoplankton increase in subpolar regions, here we show that deeper mixed layers in the NASG can be warmer and host a higher phytoplankton biomass. These results emphasize that different modes of climate variability regulate bottom-up (NAO control) and top-down (AMO control) forcing on phytoplankton at decadal timescales. As a consequence, different relationships between phytoplankton, zooplankton, and their physical environment appear subject to the disparate temporal scale of the observations (seasonal, interannual, or decadal). The prediction of phytoplankton response to climate change should be built upon what is learnt from observations at the longest timescales.

  9. The analysis of Last Interglacial (MIS 5e) relative sea-level indicators: Reconstructing sea-level in a warmer world

    NARCIS (Netherlands)

    Rovere, A.; Raymo, M.E.; Vacchi, M.; Lorscheid, T; Stocchi, P.; Gómez-Pujolf, L.; Harris, D.L.; Casella, E.; O'Leary, M.J.; Hearty, P.J.

    2016-01-01

    The Last Interglacial (MIS 5e, 128–116 ka) is among the most studied past periods in Earth's history. The climate at that time was warmer than today, primarily due to different orbital conditions, with smaller ice sheets and higher sea-level. Field evidence for MIS 5e sea-level was reported from

  10. The analysis of Last Interglacial (MIS 5e) relative sea-level indicators: Reconstructing sea-level in a warmer world

    NARCIS (Netherlands)

    Rovere, A.; Raymo, M.E.; Vacchi, M.; Lorscheid, T; Stocchi, P.; Gómez-Pujolf, L.; Harris, D.L.; Casella, E.; O'Leary, M.J.; Hearty, P.J.

    2016-01-01

    The Last Interglacial (MIS 5e, 128–116 ka) is among the most studied past periods in Earth's history. The climate at that time was warmer than today, primarily due to different orbital conditions, with smaller ice sheets and higher sea-level. Field evidence for MIS 5e sea-level was reported from tho

  11. Neotropical eocene coastal floras and [sup 18]O/[sup 16]O-estimated warmer vs. cooler equatorial waters

    Energy Technology Data Exchange (ETDEWEB)

    Graham, A. (Kent State Univ., OH (United States))

    1994-03-01

    The history of the earth's sea-surface temperature (SST) in equatorial regions during the Tertiary is unsettled because of uncertainty as to the presence and extent of glaciers during the Paleogene. The [sup 16]O trapped in glaciers and subsequently released back to the ocean basins as meltwater during interglacials affects the [sup 18]O/[sup 16]O ratio of sea water, one of the variables that must be known for oxygen isotope paleotemperature analysis of calcareous fossils. Estimates of SST range from [approximately]18 to 20 C, assuming an ice-free earth, to [approximately]28 C assuming glaciers were present in the Paleogene. Low latitude SST presently averages 28C, so the former estimate gives a value 8 to 10 C cooler than present, while the latter gives a value as warm or slightly warmer than present. The figures are important for interpreting terrestrial vegetational history because the temperature differential between low and high latitudes is a major factor in determining global climates through the control of poleward transfer of heat. The middle( ) to late Eocene Gatuncillo Formation palynoflora of Panama was deposited at the ocean-continental interface at [approximately]9[degrees]N latitude. The individual components and paleocommunities are distinctly tropical and similar to the present vegetation along the Atlantic coast of southern Central America. This is consistent with data emerging from other recently studied tropical coastal biotas and represents a contribution from paleobiology toward eventually resolving the problem of Eocene equatorial marine environments. Collectively, the evidence is beginning to favor a model of Eocene SST near present values. 50 refs., 1 fig., 2 tabs.

  12. Effects of warmer and drier climate conditions on plant composition and biomass production in a Mediterranean shrubland community

    Energy Technology Data Exchange (ETDEWEB)

    Dato, G. De; Angelis, P. De [Univ. of Tuscia, Viterbo (Italy). Dept. of Forest Environment and Resources; Pellizzaro, G.; Cesaraccio, C.; Duce, P. [National Research Council Institute of Biometeorology, Sassari (Italy); Sirca, C.; Spano, D. [Univ. of Sassari (Italy). Dept. of Economics and Wood Plant Ecosystems; Scarascia Mugnozza, G. [National Research Council Institute of Agro-Environmental and Forest Biology, Roma (Italy)

    2008-09-30

    The last Intergovernmental Panel on Climate Change (IPCC) report predicts warmer and drier conditions for the future European climate and the Mediterranean basin could be highly sensitive to future climatic change. In order to investigate how the forecast more stressing factors could affect Mediterranean shrubland ecosystems, an appropriate manipulation of the microclimate was carried out in an area covered by Mediterranean maquis aimed at extending the drought period and increasing the night-time temperature. Soil cover, plant growth, litterfall, leaf water status, and leaf nutritional status were monitored over three growing seasons. The manipulation altered the microclimate according to common scenarios, increasing mean annual night-time air temperature by about 1{sup o}C and mean annual temperature by about 0.5 {sup o}C, and decreasing precipitation between 6-46% of the total rainfall during the growing seasons. A general increase of vegetation cover was observed in the whole community during the three years of experimentation. This positive temporal pattern was mainly observed in control and warming treatment, whereas in the drought treatment it was less evident. At species-specific level, a clear negative effect of drought treatment was observed for C. monspeliensis percentage cover. Shoot elongation was not significantly affected by the warming treatment. A significant negative effect of drought treatment was noticed in the 2001-2002 and 2002-2003 growing seasons. An increase of N and P concentrations in the drought treatment in Cistus was observed and it can be explained by the reduced shoot growth induced by the water shortage that we had observed in the same treatment. The absence of a concentration effect on the other two species could be the signal of the different behaviour with regard to a drier climate, and therefore could be a symptom of future change in species composition. We underline the need of long-term observation, because of the different

  13. Effects of warmer and drier climate conditions on plant composition and biomass production in a Mediterranean shrubland community

    Directory of Open Access Journals (Sweden)

    De Dato G

    2006-01-01

    Full Text Available The last IPCC report predicts warmer and drier conditions for the future European climate and the Mediterranean basin could be highly sensible to future climatic change. In order to investigate how the forecast more stressing factors could affect Mediterranean shrubland ecosystems, an appropriate manipulation of the microclimate was carried out in an area covered by Mediterranean maquis aimed at extending the drought period and increasing the night-time temperature. Soil cover, plant growth, litterfall, leaf water status, and leaf nutritional status were monitored over three growing seasons. The manipulation altered the microclimate according to common scenarios, increasing mean annual night-time air temperature by about 1 �C and mean annual temperature by about 0.5 �C, and decreasing precipitation between 6-46% of the total rainfall during the growing seasons. A general increase of vegetation cover was observed in the whole community during the three years of experimentation. This positive temporal pattern was mainly observed in control and warming treatment, whereas in the drought treatment it was less evident. At species-specific level, a clear negative effect of drought treatment was observed for C. monspeliensis percentage cover. Shoot elongation was not significantly affected by the warming treatment. A significant negative effect of drought treatment was noticed in the 2001-2002 and 2002-2003 growing seasons. An increase of N and P concentrations in the drought treatment in Cistus was observed and it can be explained by the reduced shoot growth induced by the water shortage that we had observed in the same treatment. The absence of a concentration effect on the other two species could be the signal of the different behaviour with regard to a drier climate, and therefore could be a symptom of future change in species composition. We underline the need of long-term observation, because of the different responses of plants in the short

  14. Tropical forest carbon balance in a warmer world: a critical review spanning microbial- to ecosystem-scale processes.

    Science.gov (United States)

    Wood, Tana E; Cavaleri, Molly A; Reed, Sasha C

    2012-11-01

    , heterotrophic versus autotrophic respiration, thermal acclimation versus substrate limitation of plant and microbial communities, below-ground C allocation, species composition (plant and microbial), and the hydraulic architecture of roots. Whether or not tropical forests will become a source or a sink of C in a warmer world remains highly uncertain. Given the importance of these ecosystems to the global C budget, resolving this uncertainty is a primary research priority.

  15. A Global Perspective on Warmer Droughts as a Key Driver of Forest Disturbances and Tree Mortality (Invited)

    Science.gov (United States)

    Allen, C. D.

    2013-12-01

    Recent global warming, in concert with episodic droughts, is causing elevated levels of both chronic and acute forest water stress across large regions. Such increases in water stress affect forest dynamics in multiple ways, including by amplifying the incidence and severity of many significant forest disturbances, particularly drought-induced tree mortality, wildfire, and outbreaks of damaging insects and diseases. Emerging global-scale patterns of drought-related forest die-off are presented, including a newly updated map overview of documented drought- and heat-induced tree mortality events from around the world, demonstrating the vulnerability of all major forest types to forest drought stress, even in typically wet environments. Comparative patterns of drought stress and associated forest disturbances are reviewed for several regions (southwestern Australia, Inner Asia, western North America, Mediterranean Basin), including interactions among climate and various disturbance processes. From the Southwest USA, research is presented that derives a tree-ring-based Forest Drought Stress Index (FDSI) for the most regionally-widespread conifer species (Pinus edulis, Pinus ponderosa, and Pseudotsuga menziesii), demonstrating recent escalation of FDSI to extreme levels relative to the past 1000 years, due to both drought and especially warming. This new work further highlights strong correlations between drought stress and amplified forest disturbances (fire, bark beetle outbreaks), and projects that by CE 2050 anticipated regional warming will cause mean FDSI values to reach historically unprecedented levels that may exceed thresholds for the survival of current tree species in large portions of their current range in the Southwest. Similar patterns of recent climate-amplified forest disturbance risk are apparent from a variety of relatively dry regions across this planet, and given climate projections for substantially warmer temperatures and greater drought stress

  16. Tropical forest carbon balance in a warmer world: a critical review spanning microbial- to ecosystem-scale processes

    Science.gov (United States)

    Wood, Tana E.; Cavaleri, Molly A.; Reed, Sasha C.

    2012-01-01

    , heterotrophic versus autotrophic respiration, thermal acclimation versus substrate limitation of plant and microbial communities, below-ground C allocation, species composition (plant and microbial), and the hydraulic architecture of roots. Whether or not tropical forests will become a source or a sink of C in a warmer world remains highly uncertain. Given the importance of these ecosystems to the global C budget, resolving this uncertainty is a primary research priority.

  17. Quantifying the risks of winter damage on overwintering crops under future climates: Will low-temperature damage be more likely in warmer climates?

    Science.gov (United States)

    Vico, G.; Weih, M.

    2014-12-01

    Autumn-sown crops act as winter cover crop, reducing soil erosion and nutrient leaching, while potentially providing higher yields than spring varieties in many environments. Nevertheless, overwintering crops are exposed for longer periods to the vagaries of weather conditions. Adverse winter conditions, in particular, may negatively affect the final yield, by reducing crop survival or its vigor. The net effect of the projected shifts in climate is unclear. On the one hand, warmer temperatures may reduce the frequency of low temperatures, thereby reducing damage risk. On the other hand, warmer temperatures, by reducing plant acclimation level and the amount and duration of snow cover, may increase the likelihood of damage. Thus, warmer climates may paradoxically result in more extensive low temperature damage and reduced viability for overwintering plants. The net effect of a shift in climate is explored by means of a parsimonious probabilistic model, based on a coupled description of air temperature, snow cover, and crop tolerable temperature. Exploiting an extensive dataset of winter wheat responses to low temperature exposure, the risk of winter damage occurrence is quantified under conditions typical of northern temperate latitudes. The full spectrum of variations expected with climate change is explored, quantifying the joint effects of alterations in temperature averages and their variability as well as shifts in precipitation. The key features affecting winter wheat vulnerability to low temperature damage under future climates are singled out.

  18. Warmer winters modulate life history and energy storage but do not affect sensitivity to a widespread pesticide in an aquatic insect.

    Science.gov (United States)

    Arambourou, Hélène; Stoks, Robby

    2015-10-01

    Despite the increased attention for the effects of pesticides under global warming no studies tested how winter warming affects subsequent sensitivity to pesticides. Winter warming is expected to cause delayed negative effects when it increases metabolic rates and thereby depletes energy reserves. Using a common-garden experiment, we investigated the combined effect of a 4 °C increase in winter temperature and subsequent exposure to chlorpyrifos in the aquatic larvae of replicated low- and high-latitude European populations of the damselfly Ischnura elegans. The warmer winter (8 °C) resulted in a higher winter survival and higher growth rates compared to the cold winter (4 °C) commonly experienced by European high-latitude populations. Low-latitude populations were better at coping with the warmer winter, indicating thermal adaptation to the local winter temperatures. Subsequent chlorpyrifos exposure at 20 °C induced strong negative effects on survival, growth rate, lipid content and acetylcholinesterase activity while phenoloxidase activity increased. These pesticide effects were not affected by winter warming. Our results suggest that for species where winter warming has positive effects on life history, no delayed effects on the sensitivity to subsequent pesticide exposure should be expected.

  19. Stability of hemostatic proteins in canine fresh-frozen plasma thawed with a modified commercial microwave warmer or warm water bath.

    Science.gov (United States)

    Pashmakova, Medora B; Barr, James W; Bishop, Micah A

    2015-05-01

    To compare stability of hemostatic proteins in canine fresh-frozen plasma (FFP) thawed with a modified commercial microwave warmer (MCM) or warm water bath (37°C; WWB) or at room temperature (22°C). Fresh-frozen plasma obtained from 8 canine donors of a commercial blood bank. A commercial microwave warmer was modified with a thermocouple to measure surface temperature of bags containing plasma. The MCM and a WWB were each used to concurrently thaw a 60-mL bag of plasma obtained from the same donor. Two 3-mL control aliquots of FFP from each donor were thawed to room temperature without use of a heating device. Concentrations of hemostatic proteins, albumin, and D-dimers; prothrombin time (PT); and activated partial thromboplastin time (aPTT) were determined for all samples. Significant decreases in concentrations of factors II, IX, X, XI, fibrinogen, von Willebrand factor, antithrombin, protein C, and albumin and significant increases in PT and aPTT were detected for plasma thawed with the MCM, compared with results for samples thawed with the WWB. Concentrations of factors VII, VIII, and XII were not significantly different between plasma thawed with the MCM and WWB. Concentrations of D-dimers were above the reference range for all thawed samples regardless of thawing method. No significant differences in factor concentrations were detected between control and WWB-thawed samples. Significant differences in hemostatic protein concentrations and coagulation times were detected for plasma thawed with an MCM but not between control and WWB-thawed samples. Clinical importance of these changes should be investigated.

  20. ANALYSIS ON ENERGY CONSUMPTION CONTRIBUTE TO WEATHER WARMER%试析人类耗用能源对气候变暖的贡献

    Institute of Scientific and Technical Information of China (English)

    宿伯杰

    2001-01-01

    在对地球气候变暖原因的探讨中,人们较注意“温室气体”的贡献,但与“温室气体”排放几乎同时进行的巨额热量的释放也是不应忽视的;由205个国家和地区在1年内消耗的商品能源量数据,计算出每年释放的热量相当于地球接受30分钟的太阳辐射量,在绝热情况下可使全球陆地2m厚的表层、全球海洋2[k25]m深的水体和全球大气温度提高0.06℃;对上述结果进行了讨论。%Scientists pay much attention to the contribution of greenhouse gas in the research of the reasons of weather getting warmer and warmer, but almost in the same time with the release of greenhouse gas, a huge heat released; based on the commodity energy consume data of 205 countries and regions in theworld a year. The author gets a result that the heat correspond to the solar radiation energy the Earth gets in 30 minutes; in heat insulation case, this heat can make the temprature of 2m deep of all the land and the ocean on the Earth and all atmosphere rises 0.06℃; with discussion about the result.

  1. Statistical downscaling of North Atlantic tropical cyclone frequency and the amplified role of the Caribbean low-level jet in a warmer climate

    Science.gov (United States)

    Jones, Jhordanne J.; Stephenson, Tannecia S.; Taylor, Michael A.; Campbell, Jayaka D.

    2016-04-01

    This study assesses the skill of four statistical models in hindcasting North Atlantic annual tropical cyclone (TC) frequency over 1950-2008 with the aim of projecting future activity. Three of the models are motivated by operational statistical forecast schemes and are premised on standard hurricane predictors including sea surface temperatures (SSTs) and near-surface zonal winds. The fourth model uses an SST gradient index previously proposed for Caribbean seasonal rainfall prediction. The statistical models, created from backward regression, explain 24-48% of the observed variability in 1950-2008 annual TC frequency. The future state of the predictors is extracted from the ECHAM5, HadCM3, MRI CGCM2.3.2a, and MIROC3.2 global climate model (GCM) simulations under the Coupled Model Intercomparison Project Phase 3. Models utilizing SST and near-surface wind predictors suggest significant increases in mean annual frequency by 2-8 TCs by 2070-2090, compared to a single surface wind predictor model, indicating that positive trends in SSTs under global warming have a larger relative influence on projections than changes in the variability of the surface winds. Wind-only models exhibit declines in TC frequency, while the SST gradient model yields little change relative to the present-day mean. Backward regression reapplied against the 1990-2008 period, analogous to future warmer oceanic and atmospheric state relative to the earlier years in the record, retains only the Caribbean low-level jet (CLLJ)-type predictors, explaining up to 82% of TC frequency variability and suggesting a more dominant role for the CLLJ in a warmer climate. Projections using the new models show either a more conservative increase or a stronger decrease in frequency, consistent with a stronger CLLJ.

  2. Hybridization in a warmer world.

    Science.gov (United States)

    Chunco, Amanda J

    2014-05-01

    Climate change is profoundly affecting the evolutionary trajectory of individual species and ecological communities, in part through the creation of novel species assemblages. How climate change will influence competitive interactions has been an active area of research. Far less attention, however, has been given to altered reproductive interactions. Yet, reproductive interactions between formerly isolated species are inevitable as populations shift geographically and temporally as a result of climate change, potentially resulting in introgression, speciation, or even extinction. The susceptibility of hybridization rates to anthropogenic disturbance was first recognized in the 1930s. To date, work on anthropogenically mediated hybridization has focused primarily on either physical habitat disturbance or species invasion. Here, I review recent literature on hybridization to identify how ecological responses to climate change will increase the likelihood of hybridization via the dissolution of species barriers maintained by habitat, time, or behavior. Using this literature, I identify several cases where novel hybrid zones have recently formed, likely as a result of changing climate. Future research should focus on identifying areas and taxonomic groups where reproductive species interactions are most likely to be influenced by climate change. Furthermore, a better understanding of the evolutionary consequences of climate-mediated secondary contact is urgently needed. Paradoxically, hybridization is both a major conservation concern and an important source of novel genetic and phenotypic variation. Hybridization may therefore both contribute to increasing rates of extinction and stimulate the creation of novel phenotypes that will speed adaptation to novel climates. Predicting which result will occur following secondary contact will be an important contribution to conservation for many species.

  3. Warmer amps for the LHC

    CERN Multimedia

    Anaïs Schaeffer

    2012-01-01

    CERN is working together with an Italian company to develop superconducting cables that can function at temperatures of up to 25 K (-248°C). This will make it possible to move LHC magnet power supplies out of the tunnel, protecting them from exposure to the showers of very high-energy particles produced by the accelerator.   Figure 1: devices of this type, which measure approximately 10 metres in length, are inserted between the accelerating magnets at different points along the LHC. When it comes to consuming electricity, the magnets that steer particles through large accelerators can be characterised with just one word: greedy. For the LHC, the total current can reach 1.5 million amps. At the present time, this current is brought in via copper cables of up to 10 cm in diameter. In the tunnel, these cables connect the current leads - which provide the transition between the ambient-temperature cables and the magnets in their bath of superfluid helium - to the power supply. In the a...

  4. Warmer and Wetter Soil Stimulates Assimilation More than Respiration in Rainfed Agricultural Ecosystem on the China Loess Plateau: The Role of Partial Plastic Film Mulching Tillage.

    Science.gov (United States)

    Gong, Daozhi; Hao, Weiping; Mei, Xurong; Gao, Xiang; Liu, Qi; Caylor, Kelly

    2015-01-01

    Effects of agricultural practices on ecosystem carbon storage have acquired widespread concern due to its alleviation of rising atmospheric CO2 concentrations. Recently, combining of furrow-ridge with plastic film mulching in spring maize ecosystem was widely applied to boost crop water productivity in the semiarid regions of China. However, there is still limited information about the potentials for increased ecosystem carbon storage of this tillage method. The objective of this study was to quantify and contrast net carbon dioxide exchange, biomass accumulation and carbon budgets of maize (Zea maize L.) fields under the traditional non-mulching with flat tillage (CK) and partial plastic film mulching with furrow-ridge tillage (MFR) on the China Loess Plateau. Half-hourly net ecosystem CO2 exchange (NEE) of both treatments were synchronously measured with two eddy covariance systems during the growing seasons of 2011 through 2013. At same time green leaf area index (GLAI) and biomass were also measured biweekly. Compared with CK, the warmer and wetter (+1.3°C and +4.3%) top soil at MFR accelerated the rates of biomass accumulation, promoted greater green leaf area and thus shortened the growing seasons by an average value of 10.4 days for three years. MFR stimulated assimilation more than respiration during whole growing season, resulting in a higher carbon sequestration in terms of NEE of -79 gC/m2 than CK. However, after considering carbon in harvested grain (or aboveground biomass), there is a slight higher carbon sink (or a stronger carbon source) in MFR due to its greater difference of aboveground biomass than that of grain between both treatments. These results demonstrate that partial plastic film mulched furrow-ridge tillage with aboveground biomass exclusive of grain returned to the soil is an effective way to enhance simultaneously carbon sequestration and grain yield of maize in the semiarid regions.

  5. Warmer and Wetter Soil Stimulates Assimilation More than Respiration in Rainfed Agricultural Ecosystem on the China Loess Plateau: The Role of Partial Plastic Film Mulching Tillage.

    Directory of Open Access Journals (Sweden)

    Daozhi Gong

    Full Text Available Effects of agricultural practices on ecosystem carbon storage have acquired widespread concern due to its alleviation of rising atmospheric CO2 concentrations. Recently, combining of furrow-ridge with plastic film mulching in spring maize ecosystem was widely applied to boost crop water productivity in the semiarid regions of China. However, there is still limited information about the potentials for increased ecosystem carbon storage of this tillage method. The objective of this study was to quantify and contrast net carbon dioxide exchange, biomass accumulation and carbon budgets of maize (Zea maize L. fields under the traditional non-mulching with flat tillage (CK and partial plastic film mulching with furrow-ridge tillage (MFR on the China Loess Plateau. Half-hourly net ecosystem CO2 exchange (NEE of both treatments were synchronously measured with two eddy covariance systems during the growing seasons of 2011 through 2013. At same time green leaf area index (GLAI and biomass were also measured biweekly. Compared with CK, the warmer and wetter (+1.3°C and +4.3% top soil at MFR accelerated the rates of biomass accumulation, promoted greater green leaf area and thus shortened the growing seasons by an average value of 10.4 days for three years. MFR stimulated assimilation more than respiration during whole growing season, resulting in a higher carbon sequestration in terms of NEE of -79 gC/m2 than CK. However, after considering carbon in harvested grain (or aboveground biomass, there is a slight higher carbon sink (or a stronger carbon source in MFR due to its greater difference of aboveground biomass than that of grain between both treatments. These results demonstrate that partial plastic film mulched furrow-ridge tillage with aboveground biomass exclusive of grain returned to the soil is an effective way to enhance simultaneously carbon sequestration and grain yield of maize in the semiarid regions.

  6. Technology installation review. A case study on energy-efficient technologies

    Energy Technology Data Exchange (ETDEWEB)

    Baxter, Van [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

    2001-12-31

    The purpose of this Technology Installation Review is to provide an overview of hybrid geothermal heat pump systems. It presents the results of recent research on these systems, looks at system types, energy savings, maintenance considerations, and measured technology performance from several examples. Using the ground as a thermal energy source and/or a heat sink for heat pumps has long been recognized to have a number of advantages over the similar use of ambient air. Ground temperatures at about 3-ft depth or lower are much less variable than ambient air temperatures. Further, soil or rock at these depths is usually warmer than ambient air during the coldest winter months and cooler than ambient air during the summer months. This fact leads directly to cooler condensation temperatures (during cooling operation) and warmer evaporating temperatures (during heating) for a heat pump with consequent improved energy efficiency. It also results in increased heating and cooling capacity at extreme temperatures, thereby reducing or eliminating the need for auxiliary heat.

  7. Epidemiology: Malaria in a warmer West Africa

    Science.gov (United States)

    Caminade, C.; Jones, A. E.

    2016-11-01

    Malaria risk in West Africa is expected to fall (western region) or remain the same (eastern region) in response to climate change over the twenty-first century. This is primarily due to extreme temperature conditions projected under a high greenhouse gas emissions scenario.

  8. A hypothesis and a case-study projection of an influence of MJO modulation on boreal-summer tropical cyclogenesis in a warmer climate with a global non-hydrostatic model: a transition toward the central Pacific?

    Directory of Open Access Journals (Sweden)

    KAZUYOSHI eOOUCHI

    2014-02-01

    Full Text Available The eastward shift of the enhanced activity of tropical cyclone to the central Pacific is a robust projection result for a future warmer climate, and is shared by most of the state-of-the-art climate models. The shift has been argued to originate from the underlying El-Ñino like sea-surface temperature (SST forcing. This study explores the possibility that the change of the activity of the Madden-Julian Oscillation (MJO can be an additional, if not alternative, contributor to the shift, using the dataset of Yamada et al. (2010 from a global non-hydrostatic 14-km grid mesh time-slice experiment for a boreal-summer case. Within the case-study framework, we develop the hypothesis that an eastward shift of the high-activity area of the MJO, as manifested itself as the significant intra-seasonal modulation of the enhanced precipitation, is associated with the increased tropical cyclogenesis potential over the North central Pacific by regulating cyclonic relative vorticity and vertical shear. In contrast, the North Indian Ocean and maritime continent undergo relatively diminished genesis potential. An implication is that uncertainty in the future tropical cyclogenesis in some part of the Pacific and other ocean basins could be reduced if projection of the MJO and its connection with the underlying SST environment can be better understood and constrained by the improvement of climate models.

  9. CHP Technologies

    Science.gov (United States)

    Learn about CHP technologies, including reciprocating engines, combustion turbines, steam turbines, microturbines, fuel cells, and waste heat to power. Access the Catalog of CHP Technologies and the Biomass CHP Catalog of Technologies.

  10. Assistive Technology

    Science.gov (United States)

    ... Page Resize Text Printer Friendly Online Chat Assistive Technology Assistive technology (AT) is any service or tool that helps ... be difficult or impossible. For older adults, such technology may be a walker to improve mobility or ...

  11. Technology Maturity is Technology Superiority

    Science.gov (United States)

    2008-09-09

    Dominant Air Power: Design For Tomorrow…Deliver Today 2 TECHNOLOGY MATURITY CONFERENCE • ONE DEFINITION OF MATURITY – GOOD JUDGEMENT COMES FROM...EXPERIENCE—EXPERIENCE COMES FROM BAD JUDGEMENT Dominant Air Power: Design For Tomorrow…Deliver Today 3 TECHNOLOGY MATURITY CONFERENCE • THIS WILL BE A...2008 TECHNOLOGY MATURITY CONFERENCE “ TECHNOLOGY MATURITY IS TECHNOLOGY SUPERIORITY” Aeronautical Systems Center Dr. Tom Christian ASC/EN, WPAFB OH

  12. Globalization & technology

    DEFF Research Database (Denmark)

    Narula, Rajneesh

    Technology and globalization are interdependent processes. Globalization has a fundamental influence on the creation and diffusion of technology, which, in turn, affects the interdependence of firms and locations. This volume examines the international aspect of this interdependence at two levels...

  13. Living Technology

    DEFF Research Database (Denmark)

    2010-01-01

    This book is aimed at anyone who is interested in learning more about living technology, whether coming from business, the government, policy centers, academia, or anywhere else. Its purpose is to help people to learn what living technology is, what it might develop into, and how it might impact...... our lives. The phrase 'living technology' was coined to refer to technology that is alive as well as technology that is useful because it shares the fundamental properties of living systems. In particular, the invention of this phrase was called for to describe the trend of our technology becoming...... increasingly life-like or literally alive. Still, the phrase has different interpretations depending on how one views what life is. This book presents nineteen perspectives on living technology. Taken together, the interviews convey the collective wisdom on living technology's power and promise, as well as its...

  14. Living Technology

    DEFF Research Database (Denmark)

    2010-01-01

    This book is aimed at anyone who is interested in learning more about living technology, whether coming from business, the government, policy centers, academia, or anywhere else. Its purpose is to help people to learn what living technology is, what it might develop into, and how it might impact...... our lives. The phrase 'living technology' was coined to refer to technology that is alive as well as technology that is useful because it shares the fundamental properties of living systems. In particular, the invention of this phrase was called for to describe the trend of our technology becoming...... increasingly life-like or literally alive. Still, the phrase has different interpretations depending on how one views what life is. This book presents nineteen perspectives on living technology. Taken together, the interviews convey the collective wisdom on living technology's power and promise, as well as its...

  15. Past Warmer Climate Periods at the Antarctic Margin Detected From Proxies and Measurements of Biogenic Opal in the AND-1B Core: The XRF Spectral Silver (Ag) Peak Used as a new Tool for Biogenic Opal Quantification.

    Science.gov (United States)

    Kuhn, G.; Helling, D.; von Eynatten, H.; Niessen, F.; Magens, D.

    2008-12-01

    Quantification of biogenic opal in marine sediments is a time consuming job, but the results could indicate periods of higher bioproductivity and warmer conditions than today at the Antarctic margin. Within the international Antarctic Geological Drilling Program (ANDRILL), core AND-1B was drilled and recovered a 1285 m sequence from a flexural moat basin filled with glacimarine, terrigenous, volcanic and biogenic sediments below the McMurdo Ice Shelf. Our main goal is to study the variability and the stability of the Ross Ice Shelf from Miocene to Recent. The melting and collapse of large Antarctic ice shelves may cause a significant sea level rise because of accelerated inland ice glacier surges into the ocean. Biogenic opal content in sediments can be deduced indirectly from grain density measurements on single samples, or faster and more continuous by gamma ray attenuation measurements on the core, with subsequent wet bulk and grain density calculations. Spectral colour reflectance (b* value) measurements on the split core surface can also be a fast tool for opal content quantification. Of course, they all have disadvantages in comparison to direct measurement on samples using X-ray diffraction or geochemical leaching methods. Some major and minor chemical elements were measured directly on split core surfaces with a non- destructive X-Ray Fluorescence Core Scanner method (XRF-CS, Avaatech) in the field. Quantitative geochemical analyses like determination of total inorganic and organic carbon (TOC), biogenic opal as well as major and minor elements were done on core samples. We found a strong positive correlation between the counts per second of the XRF-CS Ag peak area and the biogenic opal content of the samples (r=0.81) not only in the AND-1B core but in others as well from the Antarctic margin. In literature, it is noted that diatoms could accumulate Ag in sediments, so at first we were pleased to find this Ag enrichment with our tool. But further

  16. Emerging Technologies

    OpenAIRE

    Salgar, S. M.

    2004-01-01

    Phenomenal advancements have taken place in the field of Information and communication technologies in the last decade. Spectacular and innovative changes are expected to take place in these fields in coming decade. Networking technologies are going through a sea change. This paper enumerates the likely networking technologies which are emerging, particularly WLANs. Most of the personal communication in the country will be through cellular/ mobile technologies, which are also covered in the p...

  17. Soulful Technologies

    DEFF Research Database (Denmark)

    Fausing, Bent

    2010-01-01

    or anthropomorphism is important for the branding of new technology. Technology is seen as creating a techno-transcendence towards a more qualified humanity which is in contact with fundamental human values like intuition, vision, and sensing; all the qualities that technology, industrialization, and rationalization...

  18. Technology Tiers

    DEFF Research Database (Denmark)

    Karlsson, Christer

    2015-01-01

    A technology tier is a level in a product system: final product, system, subsystem, component, or part. As a concept, it contrasts traditional “vertical” special technologies (for example, mechanics and electronics) and focuses “horizontal” feature technologies such as product characteristics...

  19. Technology Tiers

    DEFF Research Database (Denmark)

    Karlsson, Christer

    2015-01-01

    A technology tier is a level in a product system: final product, system, subsystem, component, or part. As a concept, it contrasts traditional “vertical” special technologies (for example, mechanics and electronics) and focuses “horizontal” feature technologies such as product characteristics...

  20. Assistive Technologies

    Science.gov (United States)

    Auat Cheein, Fernando A., Ed.

    2012-01-01

    This book offers the reader new achievements within the Assistive Technology field made by worldwide experts, covering aspects such as assistive technology focused on teaching and education, mobility, communication and social interactivity, among others. Each chapter included in this book covers one particular aspect of Assistive Technology that…

  1. Sensemaking technologies

    DEFF Research Database (Denmark)

    Madsen, Charlotte Øland

    Research scope: The scope of the project is to study technological implementation processes by using Weick's sensemaking concept (Weick, 1995). The purpose of using a social constructivist approach to investigate technological implementation processes is to find out how new technologies transform......, Orlikowski 2000). Viewing the use of technology as a process of enactment opens up for investigating the social processes of interpreting new technology into the organisation (Orlikowski 2000). The scope of the PhD project will therefore be to gain a deeper understanding of how the enactment of new...... & Brass, 1990; Kling 1991; Orlikowski 2000). It also demonstrates that technology is a flexible variable adapted to the organisation's needs, culture, climate and management philosophy, thus leading to different uses and outcomes of the same technology in different organisations (Barley 1986; 1990...

  2. Appropriate Technology as Indian Technology.

    Science.gov (United States)

    Barry, Tom

    1979-01-01

    Describes the mounting enthusiasm of Indian communities for appropriate technology as an inexpensive means of providing much needed energy and job opportunities. Describes the development of several appropriate technology projects, and the goals and activities of groups involved in utilizing low scale solar technology for economic development on…

  3. Sensemaking technologies

    DEFF Research Database (Denmark)

    Madsen, Charlotte Øland

    & Brass, 1990; Kling 1991; Orlikowski 2000). It also demonstrates that technology is a flexible variable adapted to the organisation's needs, culture, climate and management philosophy, thus leading to different uses and outcomes of the same technology in different organisations (Barley 1986; 1990......, Orlikowski 2000). Viewing the use of technology as a process of enactment opens up for investigating the social processes of interpreting new technology into the organisation (Orlikowski 2000). The scope of the PhD project will therefore be to gain a deeper understanding of how the enactment of new...

  4. Chemistry Technology

    Data.gov (United States)

    Federal Laboratory Consortium — Chemistry technology experts at NCATS engage in a variety of innovative translational research activities, including:Design of bioactive small molecules.Development...

  5. Thermally activated technologies: Technology Roadmap

    Energy Technology Data Exchange (ETDEWEB)

    None, None

    2003-05-01

    The purpose of this Technology Roadmap is to outline a set of actions for government and industry to develop thermally activated technologies for converting America’s wasted heat resources into a reservoir of pollution-free energy for electric power, heating, cooling, refrigeration, and humidity control. Fuel flexibility is important. The actions also cover thermally activated technologies that use fossil fuels, biomass, and ultimately hydrogen, along with waste heat.

  6. Thermally activated technologies: Technology Roadmap

    Energy Technology Data Exchange (ETDEWEB)

    None, None

    2003-05-01

    The purpose of this Technology Roadmap is to outline a set of actions for government and industry to develop thermally activated technologies for converting America’s wasted heat resources into a reservoir of pollution-free energy for electric power, heating, cooling, refrigeration, and humidity control. Fuel flexibility is important. The actions also cover thermally activated technologies that use fossil fuels, biomass, and ultimately hydrogen, along with waste heat.

  7. Plastics Technology.

    Science.gov (United States)

    Barker, Tommy G.

    This curriculum guide is designed to assist junior high schools industrial arts teachers in planning new courses and revising existing courses in plastics technology. Addressed in the individual units of the guide are the following topics: introduction to production technology; history and development of plastics; safety; youth leadership,…

  8. Lasers technology

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2011-07-01

    The Lasers Technology Program of IPEN is committed to the development of new lasers based on the research of optical materials and new technologies, as well to laser applications in several areas: Nuclear, Medicine, Dentistry, Industry, Environment and Advanced Research. The Program is basically divided into two main areas: Material and Laser Development and Laser Applications.

  9. Maritime Technology

    DEFF Research Database (Denmark)

    Sørensen, Herman

    1997-01-01

    Elementary introduction to the subject "Maritime Technology".The contents include drawings, sketches and references in English without any supplementary text.......Elementary introduction to the subject "Maritime Technology".The contents include drawings, sketches and references in English without any supplementary text....

  10. Maritime Technology

    DEFF Research Database (Denmark)

    Sørensen, Herman

    1997-01-01

    Elementary introduction to the subject "Maritime Technology".The contents include drawings, sketches and references in English without any supplementary text.......Elementary introduction to the subject "Maritime Technology".The contents include drawings, sketches and references in English without any supplementary text....

  11. Technology Push

    Science.gov (United States)

    Kennedy, Mike

    2008-01-01

    When students, teachers, administrators and others employed in education arrive at work every day on thousands of campuses across the nation, it should come as no surprise that at every step along the way, technology is there to greet them. Technological advancements in education, as well as in facilities operation and management, are not a…

  12. Sensemaking technology

    DEFF Research Database (Denmark)

    Madsen, Charlotte Øland

    Research objective: The object of the LOK research project is to gain a better understanding of the technological strategic processes in organisations by using the concept/metaphor of sensemaking. The project will investigate the technological strategies in organisations in order to gain a deeper...... understanding of the cognitive competencies and barriers towards implementing new technology in organisations. The research will therefore concentrate on researching the development process in the organisation's perception of the external environmental elements of customers, suppliers, competitors, internal...... and external technology and legislation and the internal environmental elements of structure, power relations and political arenas. All of these variables have influence on which/how technologies are implemented thus creating different outcomes all depending on the social dynamics that are triggered by changes...

  13. Sensemaking technology

    DEFF Research Database (Denmark)

    Madsen, Charlotte Øland

    Research objective: The object of the LOK research project is to gain a better understanding of the technological strategic processes in organisations by using the concept/metaphor of sensemaking. The project will investigate the technological strategies in organisations in order to gain a deeper...... understanding of the cognitive competencies and barriers towards implementing new technology in organisations. The research will therefore concentrate on researching the development process in the organisation's perception of the external environmental elements of customers, suppliers, competitors, internal...... and external technology and legislation and the internal environmental elements of structure, power relations and political arenas. All of these variables have influence on which/how technologies are implemented thus creating different outcomes all depending on the social dynamics that are triggered by changes...

  14. Technology collaboration

    Energy Technology Data Exchange (ETDEWEB)

    Thomas, Jacob [Halliburton (Brazil)

    2011-07-01

    The aim of this paper is to present Halliburton's Brazilian technology center. Halliburton has technology centers in the United States, Saudi Arabia, India, Singapore and Brazil, all of which aim at delivering accelerated innovation in the oil sector. The technology centers engage in research and development activities with the help of various universities and in collaboration with the customer or supplier. The Halliburton Brazil technology center provides its customers with timely research and development solutions for enhancing recovery and mitigating reservoir uncertainty; they are specialized in finding solutions for pre- and post-salt carbonate drilling and in the enhancement of production from mature fields. This presentation showcased the work carried out by the Halliburton Brazil technology center to help customers develop their deepwater field activities.

  15. Ergonomics technology

    Science.gov (United States)

    Jones, W. L.

    1977-01-01

    Major areas of research and development in ergonomics technology for space environments are discussed. Attention is given to possible applications of the technology developed by NASA in industrial settings. A group of mass spectrometers for gas analysis capable of fully automatic operation has been developed for atmosphere control on spacecraft; a version for industrial use has been constructed. Advances have been made in personal cooling technology, remote monitoring of medical information, and aerosol particle control. Experience gained by NASA during the design and development of portable life support units has recently been applied to improve breathing equipment used by fire fighters.

  16. Technology Innovation

    Science.gov (United States)

    EPA produces innovative technologies and facilitates their creation in line with the Agency mission to create products such as the stormwater calculator, remote sensing, innovation clusters, and low-cost air sensors.

  17. Banana technology

    Science.gov (United States)

    van Amstel, Willem D.; Schellekens, E. P. A.; Walravens, C.; Wijlaars, A. P. F.

    1999-09-01

    With 'Banana Technology' an unconventional hybrid fabrication technology is indicated for the production of very large parabolic and hyperbolic cylindrical mirror systems. The banana technology uses elastic bending of very large and thin glass substrates and fixation onto NC milled metal moulds. This technology has matured during the last twenty years for the manufacturing of large telecentric flat-bed scanners. Two construction types, called 'internal banana' and 'external banana; are presented. Optical figure quality requirements in terms of slope and curvature deviations are discussed. Measurements of these optical specifications by means of a 'finishing rod' type of scanning deflectometer or slope tester are presented. Design constraints for bending glass and the advantages of a new process will be discussed.

  18. Exploration technology

    Energy Technology Data Exchange (ETDEWEB)

    Roennevik, H.C. [Saga Petroleum A/S, Forus (Norway)

    1996-12-31

    The paper evaluates exploration technology. Topics discussed are: Visions; the subsurface challenge; the creative tension; the exploration process; seismic; geology; organic geochemistry; seismic resolution; integration; drilling; value creation. 4 refs., 22 figs.

  19. UPLIFTING TECHNOLOGY

    National Research Council Canada - National Science Library

    Thomas K Grose

    2015-01-01

      Inspired by Star Trek turbolifts, German engineering firm ThyssenKrupp says it's ready to replace cables and pulleys using maglev, or magnetic levitation technology, that enables the world's fastest...

  20. Videodisc technology

    Energy Technology Data Exchange (ETDEWEB)

    Marsh, F.E. Jr.

    1981-03-01

    An overview of the technology of videodiscs is given. The emphasis is on systems that use reflection or transmission of laser light. Possible use of videodiscs for storage of bibliographic information is considered. 6 figures, 3 tables. (RWR)

  1. Fabrication Technology

    Energy Technology Data Exchange (ETDEWEB)

    Blaedel, K.L.

    1993-03-01

    The mission of the Fabrication Technology thrust area is to have an adequate base of manufacturing technology, not necessarily resident at Lawrence Livermore National Laboratory (LLNL), to conduct the future business of LLNL. The specific goals continue to be to (1) develop an understanding of fundamental fabrication processes; (2) construct general purpose process models that will have wide applicability; (3) document findings and models in journals; (4) transfer technology to LLNL programs, industry, and colleagues; and (5) develop continuing relationships with the industrial and academic communities to advance the collective understanding of fabrication processes. The strategy to ensure success is changing. For technologies in which they are expert and which will continue to be of future importance to LLNL, they can often attract outside resources both to maintain their expertise by applying it to a specific problem and to help fund further development. A popular vehicle to fund such work is the Cooperative Research and Development Agreement with industry. For technologies needing development because of their future critical importance and in which they are not expert, they use internal funding sources. These latter are the topics of the thrust area. Three FY-92 funded projects are discussed in this section. Each project clearly moves the Fabrication Technology thrust area towards the goals outlined above. They have also continued their membership in the North Carolina State University Precision Engineering Center, a multidisciplinary research and graduate program established to provide the new technologies needed by high-technology institutions in the US. As members, they have access to and use of the results of their research projects, many of which parallel the precision engineering efforts at LLNL.

  2. Cognitive technologies

    CERN Document Server

    Mello, Alan; Figueiredo, Fabrício; Figueiredo, Rafael

    2017-01-01

    This book focuses on the next generation optical networks as well as mobile communication technologies. The reader will find chapters on Cognitive Optical Network, 5G Cognitive Wireless, LTE, Data Analysis and Natural Language Processing. It also presents a comprehensive view of the enhancements and requirements foreseen for Machine Type Communication. Moreover, some data analysis techniques and Brazilian Portuguese natural language processing technologies are also described here. .

  3. Lasers technology

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2014-07-01

    The Laser Technology Program of IPEN is developed by the Center for Lasers and Applications (CLA) and is committed to the development of new lasers based on the research of new optical materials and new resonator technologies. Laser applications and research occur within several areas such as Nuclear, Medicine, Dentistry, Industry, Environment and Advanced Research. Additional goals of the Program are human resource development and innovation, in association with Brazilian Universities and commercial partners.

  4. Fabrication Technology

    Energy Technology Data Exchange (ETDEWEB)

    Blaedel, K.L.

    1993-03-01

    The mission of the Fabrication Technology thrust area is to have an adequate base of manufacturing technology, not necessarily resident at Lawrence Livermore National Laboratory (LLNL), to conduct the future business of LLNL. The specific goals continue to be to (1) develop an understanding of fundamental fabrication processes; (2) construct general purpose process models that will have wide applicability; (3) document findings and models in journals; (4) transfer technology to LLNL programs, industry, and colleagues; and (5) develop continuing relationships with the industrial and academic communities to advance the collective understanding of fabrication processes. The strategy to ensure success is changing. For technologies in which they are expert and which will continue to be of future importance to LLNL, they can often attract outside resources both to maintain their expertise by applying it to a specific problem and to help fund further development. A popular vehicle to fund such work is the Cooperative Research and Development Agreement with industry. For technologies needing development because of their future critical importance and in which they are not expert, they use internal funding sources. These latter are the topics of the thrust area. Three FY-92 funded projects are discussed in this section. Each project clearly moves the Fabrication Technology thrust area towards the goals outlined above. They have also continued their membership in the North Carolina State University Precision Engineering Center, a multidisciplinary research and graduate program established to provide the new technologies needed by high-technology institutions in the US. As members, they have access to and use of the results of their research projects, many of which parallel the precision engineering efforts at LLNL.

  5. Technology and technology transfer: some basic issues

    OpenAIRE

    Shamsavari, Ali; Adikibi, Owen; Taha, Yasser

    2002-01-01

    This paper addresses various issues relating to technology and transfer of technology such as technology and society, technology and science, channels and models of technology transfer, the role of multinational companies in transfer of technology, etc. The ultimate objective is to pose the question of relevance of some existing models and ideas like technological independence in an increasingly globalised world economy.

  6. Technology cycles and technology revolutions

    Energy Technology Data Exchange (ETDEWEB)

    Paganetto, Luigi; Scandizzo, Pasquale Lucio

    2010-09-15

    Technological cycles have been characterized as the basis of long and continuous periods economic growth through sustained changes in total factor productivity. While this hypothesis is in part consistent with several theories of growth, the sheer magnitude and length of the economic revolutions experienced by humankind seems to indicate surmise that more attention should be given to the origin of major technological and economic changes, with reference to one crucial question: role of production and use of energy in economic development.

  7. Knowledge Technologies

    CERN Document Server

    Milton, Nick

    2008-01-01

    Several technologies are emerging that provide new ways to capture, store, present and use knowledge. This book is the first to provide a comprehensive introduction to five of the most important of these technologies: Knowledge Engineering, Knowledge Based Engineering, Knowledge Webs, Ontologies and Semantic Webs. For each of these, answers are given to a number of key questions (What is it? How does it operate? How is a system developed? What can it be used for? What tools are available? What are the main issues?). The book is aimed at students, researchers and practitioners interested in Knowledge Management, Artificial Intelligence, Design Engineering and Web Technologies. During the 1990s, Nick worked at the University of Nottingham on the application of AI techniques to knowledge management and on various knowledge acquisition projects to develop expert systems for military applications. In 1999, he joined Epistemics where he worked on numerous knowledge projects and helped establish knowledge management...

  8. Persuasive Technology

    DEFF Research Database (Denmark)

    This book constitutes the proceedings of the 5th International Conference on Persuasive Technology, PERSUASIVE 2010, held in Copenhagen Denmark in June 2010. The 25 papers presented were carefully reviewed and selected from 80 submissions. In addition three keynote papers are included in this vol......This book constitutes the proceedings of the 5th International Conference on Persuasive Technology, PERSUASIVE 2010, held in Copenhagen Denmark in June 2010. The 25 papers presented were carefully reviewed and selected from 80 submissions. In addition three keynote papers are included...... in this volume. The topics covered are emotions and user experience, ambient persuasive systems, persuasive design, persuasion profiles, designing for health, psychology of persuasion, embodied and conversational agents, economic incentives, and future directions for persuasive technology....

  9. Seafood Technology

    DEFF Research Database (Denmark)

    Børresen, Torger

    This presentation will fill the total picture of this conference between fisheries and aquaculture, blue biotech and bioconservation, by considering the optimal processing technology of marine resources from the raw material until the seafood reaches the plate of the consumer. The situation today...... must be performed such that total traceability and authenticity of the final products can be presented on demand. The most important aspects to be considered within seafood technology today are safety, healthy products and high eating quality. Safety can be divided into microbiological safety...... and not presenting any safety risk per se. Seafood is healthy due to the omega-3 fatty acids and the nutritional value of vitamins, peptides and proteins. The processing technology must however be performed such that these valuable features are not lost during production. The same applies to the eating quality. Any...

  10. Persuasive Technology

    DEFF Research Database (Denmark)

    This book constitutes the proceedings of the 5th International Conference on Persuasive Technology, PERSUASIVE 2010, held in Copenhagen Denmark in June 2010. The 25 papers presented were carefully reviewed and selected from 80 submissions. In addition three keynote papers are included in this vol......This book constitutes the proceedings of the 5th International Conference on Persuasive Technology, PERSUASIVE 2010, held in Copenhagen Denmark in June 2010. The 25 papers presented were carefully reviewed and selected from 80 submissions. In addition three keynote papers are included...... in this volume. The topics covered are emotions and user experience, ambient persuasive systems, persuasive design, persuasion profiles, designing for health, psychology of persuasion, embodied and conversational agents, economic incentives, and future directions for persuasive technology....

  11. Technology Transfer

    Science.gov (United States)

    Smith, Nanette R.

    1995-01-01

    The objective of this summer's work was to attempt to enhance Technology Application Group (TAG) ability to measure the outcomes of its efforts to transfer NASA technology. By reviewing existing literature, by explaining the economic principles involved in evaluating the economic impact of technology transfer, and by investigating the LaRC processes our William & Mary team has been able to lead this important discussion. In reviewing the existing literature, we identified many of the metrics that are currently being used in the area of technology transfer. Learning about the LaRC technology transfer processes and the metrics currently used to track the transfer process enabled us to compare other R&D facilities to LaRC. We discuss and diagram impacts of technology transfer in the short run and the long run. Significantly, it serves as the basis for analysis and provides guidance in thinking about what the measurement objectives ought to be. By focusing on the SBIR Program, valuable information regarding the strengths and weaknesses of this LaRC program are to be gained. A survey was developed to ask probing questions regarding SBIR contractors' experience with the program. Specifically we are interested in finding out whether the SBIR Program is accomplishing its mission, if the SBIR companies are providing the needed innovations specified by NASA and to what extent those innovations have led to commercial success. We also developed a survey to ask COTR's, who are NASA employees acting as technical advisors to the SBIR contractors, the same type of questions, evaluating the successes and problems with the SBIR Program as they see it. This survey was developed to be implemented interactively on computer. It is our hope that the statistical and econometric studies that can be done on the data collected from all of these sources will provide insight regarding the direction to take in developing systematic evaluations of programs like the SBIR Program so that they can

  12. Soulful Technologies

    DEFF Research Database (Denmark)

    Fausing, Bent

    2010-01-01

    Samsung introduced in 2008 a mobile phone called "Soul" made with a human touch and including itself a "magic touch". Through the analysis of a Nokia mobile phone TV-commercials I want to examine the function and form of digital technology in everyday images. The mobile phone and its digital came...... commercials and internet commercials for mobile phones from Nokia, or handheld computers, as Sony-Ericsson prefers to call them. Digital technology points towards a forgotten pre-human and not only post-human condition....

  13. Playful Technology

    DEFF Research Database (Denmark)

    Johansen, Stine Liv; Eriksson, Eva

    2013-01-01

    In this paper, the design of future services for children in Danish public libraries is discussed, in the light of new challenges and opportunities in relation to new media and technologies. The Danish government has over the last few years initiated and described a range of initiatives regarding...... in the library, the changing role of the librarians and the library space. We argue that intertwining traditional library services with new media forms and engaging play is the core challenge for future design in physical public libraries, but also that it is through new media and technology that new...

  14. Playful Technology

    DEFF Research Database (Denmark)

    Johansen, Stine Liv; Eriksson, Eva

    2013-01-01

    in the library, the changing role of the librarians and the library space. We argue that intertwining traditional library services with new media forms and engaging play is the core challenge for future design in physical public libraries, but also that it is through new media and technology that new......In this paper, the design of future services for children in Danish public libraries is discussed, in the light of new challenges and opportunities in relation to new media and technologies. The Danish government has over the last few years initiated and described a range of initiatives regarding...

  15. Architectural technology

    DEFF Research Database (Denmark)

    2005-01-01

    The booklet offers an overall introduction to the Institute of Architectural Technology and its projects and activities, and an invitation to the reader to contact the institute or the individual researcher for further information. The research, which takes place at the Institute of Architectural...... Technology at the Roayl Danish Academy of Fine Arts, School of Architecture, reflects a spread between strategic, goal-oriented pilot projects, commissioned by a ministry, a fund or a private company, and on the other hand projects which originate from strong personal interests and enthusiasm of individual...

  16. Manufacturing technologies

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-09-01

    The Manufacturing Technologies Center is an integral part of Sandia National Laboratories, a multiprogram engineering and science laboratory, operated for the Department of Energy (DOE) with major facilities at Albuquerque, New Mexico, and Livermore, California. Our Center is at the core of Sandia`s Advanced Manufacturing effort which spans the entire product realization process.

  17. Blast Technologies

    Science.gov (United States)

    2011-06-27

    Team Leader Risa Scherer Blast Mitigation Interior and Laboratory Team Leader Blast Technologies POC’s Government Point Of Contacts (POCs): To...to yield injury assessments at higher fidelities and with higher confidence UNCLASSIFIED UNCLASSIFIED Risa Scherer Blast Mitigation Interior and

  18. Energy Technology.

    Science.gov (United States)

    Eaton, William W.

    Reviewed are technological problems faced in energy production including locating, recovering, developing, storing, and distributing energy in clean, convenient, economical, and environmentally satisfactory manners. The energy resources of coal, oil, natural gas, hydroelectric power, nuclear energy, solar energy, geothermal energy, winds, tides,…

  19. Strategic Technology

    Science.gov (United States)

    2012-03-11

    the spectrum of future conflict and engagement. Technology Surprise Francis Fukuyama , in his introduction to the book Blindside, summarizes recent...atrocities or large-scale natural disasters abroad 12 Francis Fukuyama , ed, Blindside (Baltimore, MD: Brookings Institute Press, 2007), 1. 13 Defense

  20. (Environmental technology)

    Energy Technology Data Exchange (ETDEWEB)

    Boston, H.L.

    1990-10-12

    The traveler participated in a conference on environmental technology in Paris, sponsored by the US Embassy-Paris, US Environmental Protection Agency (EPA), the French Environmental Ministry, and others. The traveler sat on a panel for environmental aspects of energy technology and made a presentation on the potential contributions of Oak Ridge National Laboratory (ORNL) to a planned French-American Environmental Technologies Institute in Chattanooga, Tennessee, and Evry, France. This institute would provide opportunities for international cooperation on environmental issues and technology transfer related to environmental protection, monitoring, and restoration at US Department of Energy (DOE) facilities. The traveler also attended the Fourth International Conference on Environmental Contamination in Barcelona. Conference topics included environmental chemistry, land disposal of wastes, treatment of toxic wastes, micropollutants, trace organics, artificial radionuclides in the environment, and the use biomonitoring and biosystems for environmental assessment. The traveler presented a paper on The Fate of Radionuclides in Sewage Sludge Applied to Land.'' Those findings corresponded well with results from studies addressing the fate of fallout radionuclides from the Chernobyl nuclear accident. There was an exchange of new information on a number of topics of interest to DOE waste management and environmental restoration needs.

  1. GIG Technologies

    Science.gov (United States)

    2008-08-08

    caching • GIG as a sensor • Cyber SA/defense • Cross Domain Information Sharing • Multi-Level Security solutions • Enterprise Service Bus ( ESB ...Link Layer Technologies Integrated Link Layer All Optical Core For Terrestrial and Space Networks Separate Transmission Networks Mid-Term Integrated

  2. Geospatial Technology

    Science.gov (United States)

    Reed, Philip A.; Ritz, John

    2004-01-01

    Geospatial technology refers to a system that is used to acquire, store, analyze, and output data in two or three dimensions. This data is referenced to the earth by some type of coordinate system, such as a map projection. Geospatial systems include thematic mapping, the Global Positioning System (GPS), remote sensing (RS), telemetry, and…

  3. Sport Technology

    CSIR Research Space (South Africa)

    Kirkbride, T

    2007-11-01

    Full Text Available in design and manufacturing to virtual reality. There are carbon fiber materials used and in performance analysis that use video base technology. In the 1999 cricket World Cup, small earphones were used for Hansie to communicate with the coach and were later...

  4. Vacuum Technology

    Energy Technology Data Exchange (ETDEWEB)

    Biltoft, P J

    2004-10-15

    The environmental condition called vacuum is created any time the pressure of a gas is reduced compared to atmospheric pressure. On earth we typically create a vacuum by connecting a pump capable of moving gas to a relatively leak free vessel. Through operation of the gas pump the number of gas molecules per unit volume is decreased within the vessel. As soon as one creates a vacuum natural forces (in this case entropy) work to restore equilibrium pressure; the practical effect of this is that gas molecules attempt to enter the evacuated space by any means possible. It is useful to think of vacuum in terms of a gas at a pressure below atmospheric pressure. In even the best vacuum vessels ever created there are approximately 3,500,000 molecules of gas per cubic meter of volume remaining inside the vessel. The lowest pressure environment known is in interstellar space where there are approximately four molecules of gas per cubic meter. Researchers are currently developing vacuum technology components (pumps, gauges, valves, etc.) using micro electro mechanical systems (MEMS) technology. Miniature vacuum components and systems will open the possibility for significant savings in energy cost and will open the doors to advances in electronics, manufacturing and semiconductor fabrication. In conclusion, an understanding of the basic principles of vacuum technology as presented in this summary is essential for the successful execution of all projects that involve vacuum technology. Using the principles described above, a practitioner of vacuum technology can design a vacuum system that will achieve the project requirements.

  5. Technology Programme

    Energy Technology Data Exchange (ETDEWEB)

    Batistoni, Paola; De Marco, Francesco; Pieroni, Leonardo (ed.)

    2005-07-01

    The technology activities carried out by the Euratom-ENEA Association in the framework of the European Fusion Development Agreement concern the Next Step (International Thermonuclear Experimental Reactor - ITER), the Long-Term Programme (breeder blanket, materials, International Fusion Materials Irradiation Facility - IFMIF), Power Plant Conceptual Studies and Socio-Economic Studies. The Underlying Technology Programme was set up to complement the fusion activities as well to develop technologies with a wider range of interest. The Technology Programme mainly involves staff from the Frascati laboratories of the Fusion Technical and Scientific Unit and from the Brasimone laboratories of the Advanced Physics Technologies Unit. Other ENEA units also provide valuable contributions to the programme. ENEA is heavily engaged in component development/testing and in design and safety activities for the European Fusion Technology Programme. Although the work documented in the following covers a large range of topics that differ considerably because they concern the development of extremely complex systems, the high level of integration and coordination ensures the capability to cover the fusion system as a whole. In 2004 the most significant testing activities concerned the ITER primary beryllium-coated first wall. In the field of high-heat-flux components, an important achievement was the qualification of the process for depositing a copper liner on carbon fibre composite (CFC) hollow tiles. This new process, pre-brazed casting (PBC), allows the hot radial pressing (HRP) joining procedure to be used also for CFC-based armour monoblock divertor components. The PBC and HRP processes are candidates for the construction of the ITER divertor. In the materials field an important milestone was the commissioning of a new facility for chemical vapour infiltration/deposition, used for optimising silicon carbide composite (SiCf/SiC) components. Eight patents were deposited during 2004

  6. Hearing Assistive Technology

    Science.gov (United States)

    ... for the Public / Hearing and Balance Hearing Assistive Technology Hearing Assistive Technology: FM Systems | Infrared Systems | Induction ... Assistive Technology Systems Solutions What are hearing assistive technology systems (HATS)? Hearing assistive technology systems (HATS) are ...

  7. Communications technology

    Science.gov (United States)

    Cuccia, C. Louis; Sivo, Joseph

    1986-01-01

    The technologies for optimized, i.e., state of the art, operation of satellite-based communications systems are surveyed. Features of spaceborne active repeater systems, low-noise signal amplifiers, power amplifiers, and high frequency switches are described. Design features and capabilities of various satellite antenna systems are discussed, including multiple beam, shaped reflector shaped beam, offset reflector multiple beam, and mm-wave and laser antenna systems. Attitude control systems used with the antenna systems are explored, along with multiplexers, filters, and power generation, conditioning and amplification systems. The operational significance and techniques for exploiting channel bandwidth, baseband and modulation technologies are described. Finally, interconnectivity among communications satellites by means of RF and laser links is examined, as are the roles to be played by the Space Station and future large space antenna systems.

  8. Manufacturing technology

    Energy Technology Data Exchange (ETDEWEB)

    Leonard, J.A.; Floyd, H.L.; Goetsch, B.; Doran, L. [eds.

    1993-08-01

    This bulletin depicts current research on manufacturing technology at Sandia laboratories. An automated, adaptive process removes grit overspray from jet engine turbine blades. Advanced electronic ceramics are chemically prepared from solution for use in high- voltage varistors. Selective laser sintering automates wax casting pattern fabrication. Numerical modeling improves performance of photoresist stripper (simulation on Cray supercomputer reveals path to uniform plasma). And mathematical models help make dream of low- cost ceramic composites come true.

  9. Emerging technologies

    Energy Technology Data Exchange (ETDEWEB)

    Lu, Shin-yee

    1993-03-01

    The mission of the Emerging Technologies thrust area at Lawrence Livermore National Laboratory is to help individuals establish technology areas that have national and commercial impact, and are outside the scope of the existing thrust areas. We continue to encourage innovative ideas that bring quality results to existing programs. We also take as our mission the encouragement of investment in new technology areas that are important to the economic competitiveness of this nation. In fiscal year 1992, we have focused on nine projects, summarized in this report: (1) Tire, Accident, Handling, and Roadway Safety; (2) EXTRANSYT: An Expert System for Advanced Traffic Management; (3) Odin: A High-Power, Underwater, Acoustic Transmitter for Surveillance Applications; (4) Passive Seismic Reservoir Monitoring: Signal Processing Innovations; (5) Paste Extrudable Explosive Aft Charge for Multi-Stage Munitions; (6) A Continuum Model for Reinforced Concrete at High Pressures and Strain Rates: Interim Report; (7) Benchmarking of the Criticality Evaluation Code COG; (8) Fast Algorithm for Large-Scale Consensus DNA Sequence Assembly; and (9) Using Electrical Heating to Enhance the Extraction of Volatile Organic Compounds from Soil.

  10. Technology Management

    DEFF Research Database (Denmark)

    Pilkington, Alan

    2014-01-01

    This paper reports a bibliometric analysis (co-citation network analysis) of 10 journals in the management of technology (MOT) field. As well as introducing various bibliometric ideas, network analysis tools identify and explore the concepts covered by the field and their inter-relationships. Spe......This paper reports a bibliometric analysis (co-citation network analysis) of 10 journals in the management of technology (MOT) field. As well as introducing various bibliometric ideas, network analysis tools identify and explore the concepts covered by the field and their inter......-relationships. Specific results from different levels of analysis show the different dimensions of technology management: • Co-word terms identify themes • Journal co-citation network: linking to other disciplines • Co-citation network show concentrations of themes The analysis shows that MOT has a bridging role...... in integrating ideas from several distinct disciplines. This suggests that management and strategy are central to MOT which essentially relates to the firm rather than policy. Similarly we have a dual focus on capabilities, but can see subtle differences in how we view these ideas, either through an inwards...

  11. Agreement technologies

    CERN Document Server

    Ossowski, Sascha

    2013-01-01

    More and more transactions, whether in business or related to leisure activities, are mediated automatically by computers and computer networks, and this trend is having a significant impact on the conception and design of new computer applications. The next generation of these applications will be based on software agents to which increasingly complex tasks can be delegated, and which interact with each other in sophisticated ways so as to forge agreements in the interest of their human users. The wide variety of technologies supporting this vision is the subject of this volume. It summarises

  12. Seafood Technology

    DEFF Research Database (Denmark)

    Børresen, Torger

    -Trophic Aquaculture (IMTA) is needed to pay attention to environmental protection and continued biodiversity. Further, it is necessary to use all the raw materials provided such that present by-products and side streams in processing are being upgraded for a better use than today. Principles of blue biotechnology may......This presentation will fill the total picture of this conference between fisheries and aquaculture, blue biotech and bioconservation, by considering the optimal processing technology of marine resources from the raw material until the seafood reaches the plate of the consumer. The situation today...

  13. Photon technology. Hard photon technology; Photon technology. Hard photon gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    Research results of hard photon technology have been summarized as a part of novel technology development highly utilizing the quantum nature of photon. Hard photon technology refers to photon beam technologies which use photon in the 0.1 to 200 nm wavelength region. Hard photon has not been used in industry due to the lack of suitable photon sources and optical devices. However, hard photon in this wavelength region is expected to bring about innovations in such areas as ultrafine processing and material synthesis due to its atom selective reaction, inner shell excitation reaction, and spatially high resolution. Then, technological themes and possibility have been surveyed. Although there are principle proposes and their verification of individual technologies for the technologies of hard photon generation, regulation and utilization, they are still far from the practical applications. For the photon source technology, the laser diode pumped driver laser technology, laser plasma photon source technology, synchrotron radiation photon source technology, and vacuum ultraviolet photon source technology are presented. For the optical device technology, the multi-layer film technology for beam mirrors and the non-spherical lens processing technology are introduced. Also are described the reduction lithography technology, hard photon excitation process, and methods of analysis and measurement. 430 refs., 165 figs., 23 tabs.

  14. Wearable Technology

    Science.gov (United States)

    Watson, Amanda

    2013-01-01

    Wearable technology projects, to be useful, in the future, must be seamlessly integrated with the Flight Deck of the Future (F.F). The lab contains mockups of space vehicle cockpits, habitat living quarters, and workstations equipped with novel user interfaces. The Flight Deck of the Future is one element of the Integrated Power, Avionics, and Software (IPAS) facility, which, to a large extent, manages the F.F network and data systems. To date, integration with the Flight Deck of the Future has been limited by a lack of tools and understanding of the Flight Deck of the Future data handling systems. To remedy this problem it will be necessary to learn how data is managed in the Flight Deck of the Future and to develop tools or interfaces that enable easy integration of WEAR Lab and EV3 products into the Flight Deck of the Future mockups. This capability is critical to future prototype integration, evaluation, and demonstration. This will provide the ability for WEAR Lab products, EV3 human interface prototypes, and technologies from other JSC organizations to be evaluated and tested while in the Flight Deck of the Future. All WEAR Lab products must be integrated with the interface that will connect them to the Flight Deck of the Future. The WEAR Lab products will primarily be programmed in Arduino. Arduino will be used for the development of wearable controls and a tactile communication garment. Arduino will also be used in creating wearable methane detection and warning system.

  15. Technology maturity and technology development

    Energy Technology Data Exchange (ETDEWEB)

    Underhill, Gary K.; Carlson, Ronald A.; Clendinning, William A.; Erdos, Jozsef; Gault, John; Hall, James W.; Jones, Robert L.; Michael, Herbert K.; Powell, Paul H.; Riemann, Carl F.; Rios-Castellon, Lorenzo; Shepherd, Burchard P.; Wilson, John S.

    1976-01-01

    All of the work reported in the preceding chapters was performed in order to assess the technical, economic, and energetic feasibility of proceeding with more detailed studies of the geopressured geothermal resource. The preliminary conceptual design and costing activities represented the prime activity for component by component review of the maturity of the technology available for resource utilization facilities. The economics and energetics studies focussed attentions on the areas of major capital and energy investment; these results comprise a useful guide for focussing design in order to reduce initial and operations and maintenance costs and/or investment. The following presents a discussion of the primary technical problems identified.

  16. Incineration technologies

    CERN Document Server

    Buekens, Alfons

    2013-01-01

    Waste incineration is the art of completely combusting waste, while maintaining or reducing emission levels below current emission standards. Where possible, objectives include the recovering of energy as well as the  combustion residues.  Successful waste incineration makes it possible to achieve a deep reduction in waste volume, obtain a compact and sterile residue, and eliminate a wide array of pollutants. This book places waste incineration within the wider context of waste management, and demonstrates that, in contrast to landfills and composting, waste incineration can eliminate objectionable and hazardous properties such as flammability and toxicity, result in a significant reduction in volume, and destroy gaseous and liquid waste streams leaving little or no residues beyond those linked to flue gas neutralization and treatment. Moreover, waste incineration sterilizes and destroys putrescible matter, and produces usable heat.  Incineration Technologies first appeared as a peer-reviewed contribution ...

  17. BIOGAS TECHNOLOGY

    Directory of Open Access Journals (Sweden)

    D.B. SALUNKHE

    2012-12-01

    Full Text Available Due to scarcity of petroleum and coal it threatens supply of fuel throughout the world also problem of their combustion leads to research in different corners to get access the new sources of energy, like renewable energy resources. Solar energy, wind energy, different thermal and hydro sources of energy, biogas are all renewable energy resources. But, biogas is distinct from other renewable energies because of its characteristics of using, controlling and collecting organic wastes and at the same time producing fertilizer and water for use in agricultural irrigation. Biogas does not have any geographical limitations nor does it require advanced technology for producing energy, also it is very simple to use and apply. Anaerobic digestion is controlled biological degradation process which allows efficient capturing & utilization of biogas (approximately 60% methane and 40% carbon dioxide for energy generation. Anaerobic digestion of food waste is achievable but different types, composition of food waste results in varying degrees of methane yields, and thus the effects of mixing various types of food waste and their proportions should be determined on case by case basis.

  18. CMM Technology

    Energy Technology Data Exchange (ETDEWEB)

    Ward, Robert C.

    2008-10-20

    This project addressed coordinate measuring machine (CMM) technology and model-based engineering. CMM data analysis and delivery were enhanced through the addition of several machine types to the inspection summary program. CMM hardware and software improvements were made with the purchases of calibration and setup equipment and new model-based software for the creation of inspection programs. Kansas City Plant (KCP) personnel contributed to and influenced the development of dimensional metrology standards. Model-based engineering capabilities were expanded through the development of software for the tolerance analysis of piece parts and for the creation of model-based CMM inspection programs and inspection plans and through the purchase of off-the-shelf software for the tolerance analysis of mechanical assemblies. An obsolete database application used to track jobs in Precision Measurement was replaced by a web-based application with improved query and reporting capabilities. A potential project to address the transformation of the dimensional metrology enterprise at the Kansas City Plant was identified.

  19. Continuity of microblade technology in the Indian Subcontinent since 45 ka: implications for the dispersal of modern humans.

    Directory of Open Access Journals (Sweden)

    Sheila Mishra

    Full Text Available We extend the continuity of microblade technology in the Indian Subcontinent to 45 ka, on the basis of optical dating of microblade assemblages from the site of Mehtakheri, (22° 13' 44″ N Lat 76° 01' 36″ E Long in Madhya Pradesh, India. Microblade technology in the Indian Subcontinent is continuously present from its first appearance until the Iron Age (~3 ka, making its association with modern humans undisputed. It has been suggested that microblade technology in the Indian Subcontinent was developed locally by modern humans after 35 ka. The dates reported here from Mehtakheri show this inference to be untenable and suggest alternatively that this technology arrived in the Indian Subcontinent with the earliest modern humans. It also shows that modern humans in Indian Subcontinent and SE Asia were associated with differing technologies and this calls into question the "southern dispersal" route of modern humans from Africa through India to SE Asia and then to Australia. We suggest that modern humans dispersed from Africa in two stages coinciding with the warmer interglacial conditions of MIS 5 and MIS 3. Competitive interactions between African modern humans and Indian archaics who shared an adaptation to tropical environments differed from that between modern humans and archaics like Neanderthals and Denisovans, who were adapted to temperate environments. Thus, while modern humans expanded into temperate regions during warmer climates, their expansion into tropical regions, like the Indian Subcontinent, in competition with similarly adapted populations, occurred during arid climates. Thus modern humans probably entered the Indian Subcontinent during the arid climate of MIS 4 coinciding with their disappearance from the Middle East and Northern Africa. The out of phase expansion of modern humans into tropical versus temperate regions has been one of the factors affecting the dispersal of modern humans from Africa during the period 200

  20. Continuity of microblade technology in the Indian Subcontinent since 45 ka: implications for the dispersal of modern humans.

    Science.gov (United States)

    Mishra, Sheila; Chauhan, Naveen; Singhvi, Ashok K

    2013-01-01

    We extend the continuity of microblade technology in the Indian Subcontinent to 45 ka, on the basis of optical dating of microblade assemblages from the site of Mehtakheri, (22° 13' 44″ N Lat 76° 01' 36″ E Long) in Madhya Pradesh, India. Microblade technology in the Indian Subcontinent is continuously present from its first appearance until the Iron Age (~3 ka), making its association with modern humans undisputed. It has been suggested that microblade technology in the Indian Subcontinent was developed locally by modern humans after 35 ka. The dates reported here from Mehtakheri show this inference to be untenable and suggest alternatively that this technology arrived in the Indian Subcontinent with the earliest modern humans. It also shows that modern humans in Indian Subcontinent and SE Asia were associated with differing technologies and this calls into question the "southern dispersal" route of modern humans from Africa through India to SE Asia and then to Australia. We suggest that modern humans dispersed from Africa in two stages coinciding with the warmer interglacial conditions of MIS 5 and MIS 3. Competitive interactions between African modern humans and Indian archaics who shared an adaptation to tropical environments differed from that between modern humans and archaics like Neanderthals and Denisovans, who were adapted to temperate environments. Thus, while modern humans expanded into temperate regions during warmer climates, their expansion into tropical regions, like the Indian Subcontinent, in competition with similarly adapted populations, occurred during arid climates. Thus modern humans probably entered the Indian Subcontinent during the arid climate of MIS 4 coinciding with their disappearance from the Middle East and Northern Africa. The out of phase expansion of modern humans into tropical versus temperate regions has been one of the factors affecting the dispersal of modern humans from Africa during the period 200-40 ka.

  1. TECHNOLOGICAL WASTE DISPOSAL BY SUBSURFACE INJECTION TECHNOLOGY

    Directory of Open Access Journals (Sweden)

    Janković Branimir

    2002-12-01

    Full Text Available The application of oilfield and solution mining technology to subsurface disposal of technological wastes has proven to be an environmentally, technically and economically suitable method for the disposal of the waste generated in petroleum industry as well as other industrial branches. This paper describes the subsurface injection technology, the disposal formation characteristics, the waste disposal well design, evaluates the environmental impact of above mentioned technology and proposes a solutions for disposing of technological wastes in Croatia or nerby region by implementing underground injection technology according to the world experience (the paper is published in Croatian.

  2. Sino-EU Relations in 2009 Will Be Warmer

    Institute of Scientific and Technical Information of China (English)

    Guo Yan

    2009-01-01

    @@ In 2009, the Czech Republic officially took over the six-month EU presidency from France. Following Slovenia, the Czech Republic is the second new EU member to hold the EU presidency. The Czech Republic is currently faced with the challenge of coping with the global financial crisis and promoting EU political reform, as well as handling its own internal issues. On January 15, H.E. Mr. Vitezslav GREPL,the ambassador of the Czech Republic in China, held a press conference to address the Sino-EU relationship in 2009. H.E.Mr. Serge Abou, the EU ambassador to China and H.E. Mr. Mikael Lindstrom,the ambassador of Sweden to China also attended this conference.

  3. Stochastic dynamics of a warmer Great Barrier Reef.

    Science.gov (United States)

    Cooper, Jennifer K; Spencer, Matthew; Bruno, John F

    2015-07-01

    Pressure on natural communities from human activities continues to increase. Even unique ecosystems like the Great Barrier Reef (GBR), that until recently were considered near-pristine and well-protected, are showing signs of rapid degradation. We collated recent (1996-2006) spatiotemporal relationships between benthic community composition on the GBR and environmental variables (ocean temperature and local threats resulting from human activity). We built multivariate models of the effects of these variables on short-term dynamics, and developed an analytical approach to study their long-term consequences. We used this approach to study the effects of ocean warming under different levels of local threat. Observed short-term changes in benthic community structure (e.g., declining coral cover) were associated with ocean temperature (warming) and local threats. Our model projected that, in the long-term, coral cover of less than 10% was not implausible. With increasing temperature and/or local threats, corals were initially replaced by sponges, gorgonians, and other taxa, with an eventual moderately high probability of domination (> 50%) by macroalgae when temperature increase was greatest (e.g., 3.5 degrees C of warming). Our approach to modeling community dynamics, based on multivariate statistical models, enabled us to project how environmental change (and thus local and international policy decisions) will influence the future state of coral reefs. The same approach could be applied to other systems for which time series of ecological and environmental variables are available.

  4. Climate mechanism for stronger typhoons in a warmer world

    Science.gov (United States)

    Kang, Nam-Young; Elsner, James B.; Shin, Dong-hyun

    2016-04-01

    Violent typhoons continue to have catastrophic impacts on economies and welfare but how they are responding to global warming has yet to be fully understood. Here we use an empirical framework to explain physically why observations support a tight connection between increasing ocean warmth and the increasing intensity of super typhoons in the western North Pacific. We show that the energy needed for deep convection is on the rise with greater heat and moisture in the lower tropical troposphere but that this energy remains untapped when air pressure is high. Accordingly, tropical cyclone formation is becoming less common but those that do form are likely to reach extreme intensities from the discharge of stored energy. These thermodynamic changes to the environment most significantly influence the upper portion of extreme typhoon intensities indicating that super typhoons are likely to be stronger at the expense of overall tropical cyclone occurrences in the western North Pacific.

  5. Teleconnections in a warmer climate: the pliocene perspective

    Energy Technology Data Exchange (ETDEWEB)

    Shukla, Sonali P. [Columbia University, Deptartment of Earth and Environmental Sciences and the NASA Goddard Institute for Space Studies, New York, NY (United States); Chandler, Mark A.; Sohl, Linda E.; Jonas, Jeff; Lerner, Jean [Columbia University, Center for Climate Systems Research, New York, NY (United States); Rind, David [National Aeronautics and Space Administration, Goddard Institute for Space Studies, New York, NY (United States)

    2011-11-15

    Migrations toward altered sea surface temperature (SST) patterns in the Indo-Pacific region are present in the recent observational record and in future global warming projections. These SSTs are in the form of ''permanent'' El Nino-like (herein termed ''El Padre'') and Indian Ocean Dipole (IOD)-like patterns. The Early Pliocene Warm Period, which bears similarity to future warming projections, may have also exhibited these Indo-Pacific SST patterns, as suggested by regional terrestrial paleo-climatic data and general circulation model studies. The ability to corroborate this assessment with paleo-data reconstructions is an advantage of the warm Pliocene period that is not afforded by future warming scenarios. Thus, the Pliocene period provides us with a warm-climate perspective and test bed for understanding potential changes to future atmospheric interactions given these altered SST states. This study specifically assesses how atmospheric teleconnections from El Padre/IOD SST patterns are generated and propagate to create the regional climate signals of the Pliocene period, as these signals may be representative of future regional climatic changes as well. To do this, we construct a holistic diagnostic rubric that allows us to examine atmospheric teleconnections, both energetically and dynamically, as produced by a general circulation model. We incorporate KE', a diagnostic adapted from the eddy kinetic energy generation field, to assess the available energy transferred to these teleconnections. Using this methodology, we found that relative to our Modern Control experiments, weaker atmospheric teleconnections prevail under warm Pliocene conditions, although pathways of propagation still appear directed toward the southwestern United States from our tropical Pacific sector forcing. Propagation directly emanating from the Indian Ocean forcing sector appears to be largely blocked, although indirect teleconnective pathways appear traversing the Asian continent toward the North Pacific. The changes in the atmospheric circulation of Indian Ocean region in response to the underlying specified SST forcing (and indicated by Pliocene paleo-data) may have a host of implications for energy transfer out of and into the region, including interactions with the Asian jet stream and changes to the seasonal monsoon cycle. These interactions warrant further study in both past and future warm climate scenarios. (orig.)

  6. 21 CFR 880.5130 - Infant radiant warmer.

    Science.gov (United States)

    2010-04-01

    ...) MEDICAL DEVICES GENERAL HOSPITAL AND PERSONAL USE DEVICES General Hospital and Personal Use Therapeutic... limits, and device component failure, respectively. The device may be placed over a pediatric hospital bed or it may be built into the bed as a complete unit. (b) Classification. Class II (Special Controls...

  7. In-line Microwave Warmer for Blood and Intravenous Fluids.

    Science.gov (United States)

    1989-12-14

    34 O.D. PVC tubing or three windings of 0.12" I.D.x 0.19" O.D. Silicone tubing). 2.3 Development of Variable Power Control Several control mechanisms have...and three-pass he•ating was in Lactic acid dehydrogenase( LDH ), the absolu:2 levels of which were ciinically normal. Changes recorded here maybe

  8. Photon technology. Laser process technology; Photon technology. Laser process gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    For developing laser process technology by interaction between substance and photon, the present state, system, R and D issues and proposal of such technology were summarized. Development of the photon technology aims at the modification of bonding conditions of substances by quantum energy of photon, and the new process technology for generating ultra- high temperature and pressure fields by concentrating photon on a minute region. Photon technology contributes to not only the conventional mechanical and thermal forming and removal machining but also function added machining (photon machining) in quantum level and new machining technology ranging from macro- to micro-machining, creating a new industrial field. This technology extends various fields from the basis of physics and chemistry to new bonding technology. Development of a compact high-quality high-power high-efficiency photon source, and advanced photon transmission technology are necessary. The basic explication of an unsolved physicochemical phenomenon related to photon and substance, and development of related application technologies are essential. 328 refs., 147 figs., 13 tabs.

  9. Excimer Laser Technology

    CERN Document Server

    Basting, Dirk

    2005-01-01

    This comprehensive survey on Excimer Lasers investigates the current range of the technology, applications and devices of this commonly used laser source, as well as the future of new technologies, such as F2 laser technology. Additional chapters on optics, devices and laser systems complete this compact handbook. A must read for laser technology students, process application researchers, engineers or anyone interested in excimer laser technology. An effective and understandable introduction to the current and future status of excimer laser technology.

  10. Technology transfer by multinationals

    OpenAIRE

    Kostyantyn Zuzik

    2003-01-01

    The paper analyses the issue of technology transfer by multinational corporations. The following questions are explored: (a) world market of technologies, the role of MNCs (b) Choice of the technology transfer mode, Dunning's OLI-theory as a factor of the choice of the mode of transfer (c) measurement and profitability of technology transfer (d) transfer of technology through partnerships, JVs, alliances and through M&As (e) aspects of technology transfer by services multinationals. Paper uti...

  11. Technology transfer by multinationals

    OpenAIRE

    2003-01-01

    The paper analyses the issue of technology transfer by multinational corporations. The following questions are explored: (a) world market of technologies, the role of MNCs (b) Choice of the technology transfer mode, Dunning's OLI-theory as a factor of the choice of the mode of transfer (c) measurement and profitability of technology transfer (d) transfer of technology through partnerships, JVs, alliances and through M&As (e) aspects of technology transfer by services multinationals. Paper uti...

  12. Water Innovation and Technology

    Science.gov (United States)

    Water technologies are a specific sector that EPA works to address through the water technology cluster, aging infrastructure research, green infrastructure, and major industry meetings such as WEFTEC.

  13. Morgantown Energy Technology Center, technology summary

    Energy Technology Data Exchange (ETDEWEB)

    1994-06-01

    This document has been prepared by the DOE Environmental Management (EM) Office of Technology Development (OTD) to highlight its research, development, demonstration, testing, and evaluation activities funded through the Morgantown Energy Technology Center (METC). Technologies and processes described have the potential to enhance DOE`s cleanup and waste management efforts, as well as improve US industry`s competitiveness in global environmental markets. METC`s R&D programs are focused on commercialization of technologies that will be carried out in the private sector. META has solicited two PRDAs for EM. The first, in the area of groundwater and soil technologies, resulted in twenty-one contact awards to private sector and university technology developers. The second PRDA solicited novel decontamination and decommissioning technologies and resulted in eighteen contract awards. In addition to the PRDAs, METC solicited the first EM ROA in 1993. The ROA solicited research in a broad range of EM-related topics including in situ remediation, characterization, sensors, and monitoring technologies, efficient separation technologies, mixed waste treatment technologies, and robotics. This document describes these technology development activities.

  14. Fundamentals of technology roadmapping

    Energy Technology Data Exchange (ETDEWEB)

    Garcia, M.L.; Bray, O.H.

    1997-04-01

    Technology planning is important for many reasons. Globally, companies are facing many competitive problems. Technology roadmapping, a form of technology planning can help deal with this increasingly competitive environment. While it has been used by some companies and industries, the focus has always been on the technology roadmap as a product, not on the process. This report focuses on formalizing the process so that it can be more broadly and easily used. As a DOE national security laboratory with R&D as a major product, Sandia must do effective technology planning to identify and develop the technologies required to meet its national security mission. Once identified, technology enhancements or new technologies may be developed internally or collaboratively with external partners. For either approach, technology roadmapping, as described in this report, is an effective tool for technology planning and coordination, which fits within a broader set of planning activities. This report, the second in a series on technology roadmapping, develops and documents this technology roadmapping process, which can be used by Sandia, other national labs, universities, and industry. The main benefit of technology roadmapping is that it provides information to make better technology investment decisions by identifying critical technologies and technology gaps and identifying ways to leverage R&D investments. It can also be used as a marketing tool. Technology roadmapping is critical when the technology investment decision is not straight forward. This occurs when it is not clear which alternative to pursue, how quickly the technology is needed, or when there is a need to coordinate the development of multiple technologies. The technology roadmapping process consists of three phases - preliminary activity, development of the technology roadmap, and follow-up activity.

  15. Marketing technology in macroeconomics.

    Science.gov (United States)

    Tamegawa, Kenichi

    2012-01-01

    In this paper, we incorporate a marketing technology into a dynamic stochastic general equilibrium model by assuming a matching friction for consumption. An improvement in matching can be interpreted as an increase in matching technology, which we call marketing technology because of similar properties. Using a simulation analysis, we confirm that a positive matching technology shock can increase output and consumption.

  16. Educational Technology in China

    Science.gov (United States)

    Meifeng, Liu; Jinjiao, Lv; Cui, Kang

    2010-01-01

    This paper elaborates the two different academic views of the identity of educational technology in China at the current time--advanced-technology-oriented cognition, known as Electrifying Education, and problem-solving-oriented cognition, known as Educational Technology. It addresses five main modes of educational technology in China: as a…

  17. Marketing technologically advanced products

    NARCIS (Netherlands)

    Bender, Horst

    1989-01-01

    This paper calls for a merger of technology and marketing under a customer value perspective; for an enhancement of the traditional technological innovation orientation of the technology-based firm with a market thrust. It establishes technology-based products as product-service offerings that are d

  18. Emerging technology and ethics

    CERN Document Server

    Wakunuma, Kutoma

    2011-01-01

    This e-book on Emerging Technologies and Ethics includes a collection of essays which explore the future and ethics of emerging information and communication technologies. Articles in the collection include an overview of the legal implications which may be relevant to the ethical aspects of emerging technologies and also ethical issues arising from the mass-take up of mobile technologies.

  19. Composite Technology for Exploration

    Science.gov (United States)

    Fikes, John

    2017-01-01

    The CTE (Composite Technology for Exploration) Project will develop and demonstrate critical composites technologies with a focus on joints that utilize NASA expertise and capabilities. The project will advance composite technologies providing lightweight structures to support future NASA exploration missions. The CTE project will demonstrate weight-saving, performance-enhancing bonded joint technology for Space Launch System (SLS)-scale composite hardware.

  20. Newnes communications technology handbook

    CERN Document Server

    Lewis, Geoff

    1994-01-01

    Newnes Communications Technology Handbook provides a discussion on different topics relevant to communications technology. The book is comprised of 39 chapters that tackle a wide variety of concern in communications technology. The coverage of the text includes technologies, such as analog digital communications systems, radio frequency receiver, and satellite systems. The book also discusses some methods and techniques used in communications technology, including mixer signal processing, modulation and demodulation, and spread spectrum techniques. The text will be of great use to engineers, t

  1. Technology and Nursing

    OpenAIRE

    Maria Vera Lúcia Moreira Leitão Cardoso

    2012-01-01

    In the present age we cannot disassociate from emerging issues, which involve science, communication, health and technology, the influence of media, technological advances, and the use of computers in all spheres of life. The concepts created for technology cover various evaluation approaches, which depend upon which type of technology, approaches, usefulness and influences in a particular area of knowledge. Technological advances cover several areas, figuring quantum physics, nanotechnology,...

  2. Entry and Technological Performance in New Technology Domains : Technological Opportunities, Technology Competition and Technological Relatedness

    NARCIS (Netherlands)

    Leten, B.; Belderbos, R.; Van Looy, B.

    2016-01-01

    Entry and success in new technology domains (NTDs) is essential for firms' long-term performance. We argue that firms' choices to enter NTDs and their subsequent performance in these domains are not only governed by firm-level factors but also by environmental characteristics. Entry is encouraged by

  3. GRACE BIOREMEDIATION TECHNOLOGIES - DARAMEND™ BIOREMEDIATION TECHNOLOGY. INNOVATIVE TECHNOLOGY EVALUATION REPORT

    Science.gov (United States)

    Grace Dearborn's DARAMEND™ Bioremediation Technology was developed to treat soils/sediment contaminated with organic contaminants using solid-phase organic amendments. The amendments increase the soil’s ability to supply biologically available water/nutrients to micro...

  4. Emerging Technologies Integrating Technology into Study Abroad

    Science.gov (United States)

    Godwin-Jones, Robert

    2016-01-01

    "Ready access to travel and to technology-enhanced social networking (e.g., Facebook or Skype) has changed the nature of study abroad to the point where today's experiences are fundamentally different from those of earlier eras" (Kinginger, 2013a, p. 345). In addition to more travel options and greater technology availability, study…

  5. Payload software technology: Software technology development plan

    Science.gov (United States)

    1977-01-01

    Programmatic requirements for the advancement of software technology are identified for meeting the space flight requirements in the 1980 to 1990 time period. The development items are described, and software technology item derivation worksheets are presented along with the cost/time/priority assessments.

  6. Search Technologies | NCI Technology Transfer Center | TTC

    Science.gov (United States)

    Our team of technology transfer specialists has specialized training in invention reporting, patenting, patent strategy, executing technology transfer agreements and marketing. TTC is comprised of professionals with diverse legal, scientific, and business/marketing expertise. Most of our staff hold doctorate-level technical and/or legal training.

  7. Available Technologies | NCI Technology Transfer Center | TTC

    Science.gov (United States)

    Our team of technology transfer specialists has specialized training in invention reporting, patenting, patent strategy, executing technology transfer agreements and marketing. TTC is comprised of professionals with diverse legal, scientific, and business/marketing expertise. Most of our staff hold doctorate-level technical and/or legal training.

  8. Educational technology and the new technologies

    NARCIS (Netherlands)

    Verhagen, Pløn W.; Plomp, Tjeerd

    1989-01-01

    Like everywhere in our culture, new technologies gradually penetrate the field of education. This may be seen as a problem area, which asks for appropriate, actions by teachers, curriculum experts, instructional designers and others. As "technology" seems to be the main issue,one may quation whether

  9. SHARED TECHNOLOGY TRANSFER PROGRAM

    Energy Technology Data Exchange (ETDEWEB)

    GRIFFIN, JOHN M. HAUT, RICHARD C.

    2008-03-07

    The program established a collaborative process with domestic industries for the purpose of sharing Navy-developed technology. Private sector businesses were educated so as to increase their awareness of the vast amount of technologies that are available, with an initial focus on technology applications that are related to the Hydrogen, Fuel Cells and Infrastructure Technologies (Hydrogen) Program of the U.S. Department of Energy. Specifically, the project worked to increase industry awareness of the vast technology resources available to them that have been developed with taxpayer funding. NAVSEA-Carderock and the Houston Advanced Research Center teamed with Nicholls State University to catalog NAVSEA-Carderock unclassified technologies, rated the level of readiness of the technologies and established a web based catalog of the technologies. In particular, the catalog contains technology descriptions, including testing summaries and overviews of related presentations.

  10. ACR-700 advanced technologies

    Energy Technology Data Exchange (ETDEWEB)

    Tapping, R.L.; Turner, C.W. [Atomic Energy of Canada Limited, Chalk River, Ontario (Canada); Yu, S.K.W. [Atomic Energy of Canada Limited, Mississauga, Ontario (Canada); Olmstead, R.; Speranzini, R.A. [Atomic Energy of Canada Limited, Chalk River, Ontario (Canada)

    2004-12-01

    A successful advanced reactor plant will have optimized economics including reduced operating and maintenance costs, improved performance, and enhanced safety. Incorporating improvements based on advanced technologies ensures cost, safety and operational competitiveness of the ACR-700. These advanced technologies include modern configuration management; construction technologies; operational technology for the control centre and information systems for plant monitoring and analysis. This paper summarizes the advanced technologies used to achieve construction and operational improvements to enhance plant economic competitiveness, advances in the operational technology used for reactor control, and presents the development of the Smart CANDU suite of tools and its application to existing operating reactors and to the ACR-700. (author)

  11. [Health technology in Mexico].

    Science.gov (United States)

    Cruz, C; Faba, G; Martuscelli, J

    1992-01-01

    The features of the health technology cycle are presented, and the effects of the demographic, epidemiologic and economic transition on the health technology demand in Mexico are discussed. The main problems of science and technology in the context of a decreasing scientific and technological activity due to the economic crisis and the adjustment policies are also analyzed: administrative and planning problems, low impact of scientific production, limitations of the Mexican private sector, and the obstacles for technology assessment. Finally, this paper also discusses the main support strategies for science and technology implemented by the Mexican government during the 1980s and the challenges and opportunities that lie ahead.

  12. Technological Style is History

    DEFF Research Database (Denmark)

    Blond, Lasse

    culture, and just as importantly that culture shapes technology. By looking at a recent transfer of technology this reciprocal exchange is elaborated by considering the cultural or contextual influence in the adaptation of technology. In this connection the notion of technological style is revisited...... by questioning whether it pays due attention to the non-technical factors of the process? In order to compensate for the deficiencies of the technological style as a sensitizing device the concept of sociotechnical style is introduced – a concept more in tune with resent research in technology studies....

  13. Cloud Computing Technologies

    Directory of Open Access Journals (Sweden)

    Sean Carlin

    2012-06-01

    Full Text Available This paper outlines the key characteristics that cloud computing technologies possess and illustrates the cloud computing stack containing the three essential services (SaaS, PaaS and IaaS that have come to define the technology and its delivery model. The underlying virtualization technologies that make cloud computing possible are also identified and explained. The various challenges that face cloud computing technologies today are investigated and discussed. The future of cloud computing technologies along with its various applications and trends are also explored, giving a brief outlook of where and how the technology will progress into the future.

  14. Technology Matters - When new technology reshape innovation

    DEFF Research Database (Denmark)

    Edwards, Kasper; Pedersen, Jørgen Lindgaard

    2004-01-01

    not to be managed in the sense that aims, instruments and resources are unclear. It is observed that new technology is adopted with a limited scope and fo-cus – often to solve a particular technical problem e.g. the quality of specifica-tion are too low. For a single reason a new technology is introduced within...... the firm, which over time becomes a source of innovation. However, through adoption of this new technology firms engage in a mu-tual learning and forming process where the firm learn by using the new technol-ogy. When learning, the firm and the new technology is mutually formed as the firm tries to adopt...... learning. As the possibilities of the new hybrid tech-nology are recognised a new strategy based on the new hybrid technology is formed trying to exploit its advantages. The paper uses a number of case studies in firms implementing product configuration systems to substantiate these claims. It has been...

  15. Focus on Technologies: Worry or Technology?

    Directory of Open Access Journals (Sweden)

    Saulius Kanišauskas

    2015-10-01

    Full Text Available The paper analyses different attitudes towards technologies in contemporary philosophical discourses. It points out that classical notion of technology formulated by Martin Heidegger seems to be more and more often questioned and even forgotten. As a result, it is being replaced by the theory of determinism, according to which the change of technologies determines the changes in social systems, the human being including. This happens this way and not vice versa. Nowadays technē, or “technika” (in English: technology is mostly understood in the instrumental meaning or in the meaning of power. It is considered to be a powerful means, tool or mechanism to influence, change, control and manipulate human consciousness and human feelings. Despite the fact that technologies have already been tamed, the problem of huge responsibility for using and developing them arises. It is questioned whether the increasing society’s attention to modern technologies is not a particular “technology” of the postmodern capitalism to manipulate social consciousness. In parallel with “yes” answer to this question, Albert Borgmann’s idea that the causes of technological development have an ontological dimension, i.e. the causes are rooted in the nature of human beings themselves and their desire to adore own creativity, is discussed. Thus, it becomes necessary to probe deeper into the nature of creativity.

  16. Resources, Technology, and Strategy

    DEFF Research Database (Denmark)

    Resources, Technology and Strategy brings together contributors from Europe, North America and Asia to consider the strategic relationship between technology and other resources, such as production capabilities, marketing prowess, finance and organisational culture. Throughout the book...

  17. TECHNOLOGICAL IMPLEMENTATION PLAN

    DEFF Research Database (Denmark)

    Bellini, Anna

    2004-01-01

    This document has the purpose to describe the technological implementation plan in the IDEAL project.......This document has the purpose to describe the technological implementation plan in the IDEAL project....

  18. Technologies. [space power sources

    Science.gov (United States)

    Brandhorst, Henry W., Jr.

    1992-01-01

    Energy technologies to meet the power requirements of future space missions are reviewed. Photovoltaic, solar dynamic, and solar thermal technologies are discussed along with techniques for energy storage and power management and distribution.

  19. Technology Implementation Plan

    DEFF Research Database (Denmark)

    Jensen, Karsten Ingerslev; Schultz, Jørgen Munthe

    The Technology Implementation Plan (TIP) describes the main project results and the intended future use. The TIP is confidential.......The Technology Implementation Plan (TIP) describes the main project results and the intended future use. The TIP is confidential....

  20. INFORMATION TECHNOLOGIES IN TOURISM

    Directory of Open Access Journals (Sweden)

    Radka Tosheva

    2016-12-01

    Full Text Available In this article the focus is on the role of information technology in tourism, tourism business, electronic payments, software used by tourist companies, new technologies for online advertising and shopping, software for mobile devices.

  1. Geothermal Power Technologies

    DEFF Research Database (Denmark)

    Montagud, Maria E. Mondejar; Chamorro, C.R.

    2016-01-01

    Although geothermal energy has been widely deployed for direct use in locations with especial geologic manifestations, its potential for power generation has been traditionally underestimated. Recent technology developments in drilling techniques and power conversion technologies from low...

  2. Technology transfer for adaptation

    Science.gov (United States)

    Biagini, Bonizella; Kuhl, Laura; Gallagher, Kelly Sims; Ortiz, Claudia

    2014-09-01

    Technology alone will not be able to solve adaptation challenges, but it is likely to play an important role. As a result of the role of technology in adaptation and the importance of international collaboration for climate change, technology transfer for adaptation is a critical but understudied issue. Through an analysis of Global Environment Facility-managed adaptation projects, we find there is significantly more technology transfer occurring in adaptation projects than might be expected given the pessimistic rhetoric surrounding technology transfer for adaptation. Most projects focused on demonstration and early deployment/niche formation for existing technologies rather than earlier stages of innovation, which is understandable considering the pilot nature of the projects. Key challenges for the transfer process, including technology selection and appropriateness under climate change, markets and access to technology, and diffusion strategies are discussed in more detail.

  3. Effects of New Technologies.

    Science.gov (United States)

    Social and Labour Bulletin, 1980

    1980-01-01

    Transnational implications of technological change and innovation in telecommunications are discussed, including impact on jobs and industrial relations, computer security, access to information, and effects of technological innovation on international economic systems. (SK)

  4. CSIR Technology Impact 2000

    CSIR Research Space (South Africa)

    CSIR

    2000-01-01

    Full Text Available This millennium issue of Technology Impact celebrates the CSIR's contributions during the transitional 1999/2000 year. It presents a rich canvas portrays technology solutions and information which have touched the lives of people both within...

  5. Genealogies of Modern Technology

    DEFF Research Database (Denmark)

    Riis, Søren

    2008-01-01

    Does modern technology differ from ancient technology and does it have a unique essence? This twofold question opens one of Martin Heidegger's most influential philosophical inquiries, The Question Concerning Technology. The answer Heidegger offers has inspired various critiques and appraisals from...... a vast number of contemporary scholars of technology.1 Heidegger's answer is traditionally thought to suggest a great difference between ancient and modern technology. However, by re-examining Heidegger's text, it is possible to discover previously ignored or misunderstood lines of thoughts that affirm...... a multi-stable interpretation of the origin of modern technology. In what follows, we shall see how The Question Concerning Technology in fact supports three different genealogies of modern technology...

  6. CSIR Technology Impact 1993

    CSIR Research Space (South Africa)

    CSIR

    1993-01-01

    Full Text Available This issue of Technology Impact offers a brief snapshot of CSIR activities during the year under review by highlighting a number of innovative projects and initiatives in these areas. It presents a rich canvas portrays technology solutions...

  7. Advancement in Engineering Technology

    DEFF Research Database (Denmark)

    Kalia, Kartik; Rehman, M. Atiqur; Hussain, Dil muhammed Akbar

    2016-01-01

    In this paper we will be discussing about the impact of technology on our daily lives. How everybody is dependent upon technology in one or other way. Methods/Statistical Analysis: Technology has played a significant role in the evolution of the society. Science has produced many new ideas...... but to harvest those ideas, technology is a must. With the huge requirement of engineering equipment's, the industry needs specialists who can manage and operate these technologies. Detailed information about the merits and demerits of technology is also mentioned in this paper. Findings: Technology has affected...... the environment on a great scale; in some cases, technology is even replacing human being or use of manpower. So proper counter measures have been mentioned, which can be used to control and limit harmful effect....

  8. Technology licensing in China

    DEFF Research Database (Denmark)

    Wang, Yuandi; Li-Ying, Jason; Chen, Jin

    2015-01-01

    We explore the landscape of technology licensing among Chinese entities in the period 2000–12, using a unique database on technological licensing from the State Intellectual Property Office of China. We find that: first, among Chinese licensee organizations, firms have dominated in terms...... of the number of licensed technologies; second, the geographical distribution of licensed technologies among the provinces has gradually reached a new quantitative balance; third, utility models are the most popular technologies to be licensed and the majority of technology licensing in China has been between...... Chinese entities, and most transactions have been local within provinces; and finally, Chinese firms have gradually in-licensed newer and newer technologies, but the technologies in-licensed from foreign sources are by no means state-of-the-art. We make several suggestions for innovation policy...

  9. CSIR Technology Impact 1999

    CSIR Research Space (South Africa)

    CSIR

    1999-01-01

    Full Text Available This issue of Technology Impact offers a brief snapshot of CSIR activities during the year under review by highlighting a number of innovative projects and initiatives in these areas. It presents a rich canvas portrays technology solutions...

  10. Discourses of Technology

    DEFF Research Database (Denmark)

    Sommer, Jannek K.; Knudsen, Gry Høngsmark

    (Kozinets, 2008) as drivers of consumer acceptance of new technology. Similarly, Giesler (2008) has conceptualized consumer acceptance of technology as a form of marketplace drama, in which market ideologies are negotiated between consumers and media discourses. We suggest to study discourses around failed......In this poster we address consumption of technology from the perspective of failure. A large body of studies of consumption of technology have focused on consumer acceptance (Kozinets, 2008). These studies have identified particular narratives about social and economic progress, and pleasure...... to understand how rejection and resistance build in the imagined use of technology. The study extends research on consumption of technology by demonstrating the importance of emergent discourses of new technology. We argue that the success of a particular new technology partly depends on the imagined...

  11. CSIR Technology Impact 1996

    CSIR Research Space (South Africa)

    CSIR

    1996-01-01

    Full Text Available This issue of Technology Impact offers a brief snapshot of CSIR activities during the year under review by highlighting a number of innovative projects and initiatives in these areas. It presents a rich canvas portrays technology solutions...

  12. CSIR Technology Impact 1994

    CSIR Research Space (South Africa)

    CSIR

    1994-01-01

    Full Text Available This issue of Technology Impact offers a brief snapshot of CSIR activities during the year under review by highlighting a number of innovative projects and initiatives in these areas. It presents a rich canvas portrays technology solutions...

  13. Advancement in Engineering Technology

    DEFF Research Database (Denmark)

    Kalia, Kartik; Rehman, M. Atiqur; Hussain, Dil muhammed Akbar

    2016-01-01

    In this paper we will be discussing about the impact of technology on our daily lives. How everybody is dependent upon technology in one or other way. Methods/Statistical Analysis: Technology has played a significant role in the evolution of the society. Science has produced many new ideas...... but to harvest those ideas, technology is a must. With the huge requirement of engineering equipment's, the industry needs specialists who can manage and operate these technologies. Detailed information about the merits and demerits of technology is also mentioned in this paper. Findings: Technology has affected...... the environment on a great scale; in some cases, technology is even replacing human being or use of manpower. So proper counter measures have been mentioned, which can be used to control and limit harmful effect....

  14. Genealogies of Modern Technology

    DEFF Research Database (Denmark)

    Riis, Søren

    2008-01-01

    Does modern technology differ from ancient technology and does it have a unique essence? This twofold question opens one of Martin Heidegger's most influential philosophical inquiries, The Question Concerning Technology. The answer Heidegger offers has inspired various critiques and appraisals from...... a vast number of contemporary scholars of technology.1 Heidegger's answer is traditionally thought to suggest a great difference between ancient and modern technology. However, by re-examining Heidegger's text, it is possible to discover previously ignored or misunderstood lines of thoughts that affirm...... a multi-stable interpretation of the origin of modern technology. In what follows, we shall see how The Question Concerning Technology in fact supports three different genealogies of modern technology...

  15. New Reductive Desulfurization Technology

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    @@ The project for the research of the pulse plasma reductive desulfurization technology undertaken by Huazhong University of Science and Technology recently passed the research achievement appraisal in Wuhan, Hubei province.

  16. Nigerian journal of technology

    African Journals Online (AJOL)

    student1

    sieved into abrasive grains that were used to produce the grinding wheels. These locally ... Nigerian Journal of Technology (NIJOTECH). Vol. 32. No. 2. July 2013, pp. 318 – 324 ..... [10] Salmon, S. C. Modern Grinding Process. Technology.

  17. Neuroanatomy and transgenic technologies

    Science.gov (United States)

    This is a short review that introduces recent advances of neuroanatomy and transgenic technologies. The anatomical complexity of the nervous system remains a subject of tremendous fascination among neuroscientists. In order to tackle this extraordinary complexity, powerful transgenic technologies a...

  18. FY04 Engineering Technology Reports Technology Base

    Energy Technology Data Exchange (ETDEWEB)

    Sharpe, R M

    2005-01-27

    Lawrence Livermore National Laboratory's Engineering Directorate has two primary discretionary avenues for its investment in technologies: the Laboratory Directed Research and Development (LDRD) program and the ''Tech Base'' program. This volume summarizes progress on the projects funded for technology-base efforts in FY2004. The Engineering Technical Reports exemplify Engineering's more than 50-year history of researching and developing (LDRD), and reducing to practice (technology-base) the engineering technologies needed to support the Laboratory's missions. Engineering has been a partner in every major program and project at the Laboratory throughout its existence, and has prepared for this role with a skilled workforce and technical resources. This accomplishment is well summarized by Engineering's mission: ''Enable program success today and ensure the Laboratory's vitality tomorrow''. LDRD is the vehicle for creating those technologies and competencies that are cutting edge. These require a significant level of research or contain some unknown that needs to be fully understood. Tech Base is used to apply those technologies, or adapt them to a Laboratory need. The term commonly used for Tech Base projects is ''reduction to practice''. Tech Base projects effect the natural transition to reduction-to-practice of scientific or engineering methods that are well understood and established. They represent discipline-oriented, core competency activities that are multi-programmatic in application, nature, and scope. The objectives of technology-base funding include: (1) the development and enhancement of tools and processes to provide Engineering support capability, such as code maintenance and improved fabrication methods; (2) support of Engineering science and technology infrastructure, such as the installation or integration of a new capability; (3) support for technical and

  19. Developments in lubricant technology

    CERN Document Server

    Srivastava, S P

    2014-01-01

    Provides a fundamental understanding of lubricants and lubricant technology including emerging lubricants such as synthetic and environmentally friendly lubricants Teaches the reader to understand the role of technology involved in the manufacture of lubricants Details both major industrial oils and automotive oils for various engines Covers emerging lubricant technology such as synthetic and environmentally friendly lubricants Discusses lubricant blending technology, storage, re-refining and condition monitoring of lubricant in equipment

  20. Promoting Renewable Energy Technologies

    DEFF Research Database (Denmark)

    Olsen, Ole Jess; Skytte, Klaus

    % of its annual electricity production. In this paper, we present and discuss the Danish experience as a case of promoting renewable energy technologies. The development path of the two technologies has been very different. Wind power is considered an outright success with fast deployment to decreasing...... technology and its particular context, it is possible to formulate some general principles that can help to create an effective and efficient policy for promoting new renewable energy technologies....

  1. Emerging Technologies for Telemedicine

    Energy Technology Data Exchange (ETDEWEB)

    Minh, Cao Duc [National Agency for Science and Technology Information, Hanoi (Viet Nam); Shimizu, Shuji; Antoku, Yasuaki; Torata, Nobuhiro; Kudo, Kuriko; Okamura, Koji; Nakashima, Naoki; Tanaka, Masao [Kyushu University Hospital, Fukuoka (Japan)

    2012-02-15

    This paper focuses on new technologies that are practically useful for telemedicine. Three representative systems are introduced: a Digital Video Transport System (DVTS), an H.323 compatible videoconferencing system, and Vidyo. Based on some of our experiences, we highlight the advantages and disadvantages of each technology, and point out technologies that are especially targeted at doctors and technicians, so that those interested in using similar technologies can make appropriate choices and achieve their own goals depending on their specific conditions.

  2. Promoting Renewable Energy Technologies

    DEFF Research Database (Denmark)

    Olsen, Ole Jess; Skytte, Klaus

    % of its annual electricity production. In this paper, we present and discuss the Danish experience as a case of promoting renewable energy technologies. The development path of the two technologies has been very different. Wind power is considered an outright success with fast deployment to decreasing...... technology and its particular context, it is possible to formulate some general principles that can help to create an effective and efficient policy for promoting new renewable energy technologies....

  3. SIXTH SENSE TECHNOLOGY

    OpenAIRE

    2014-01-01

    The aim of this thesis was to explain the development of the technology by describing current hot concept in its field. The thesis describes the trend of development and current phase of the technology. The trend was described by explaining the concept of sixth sense technology and the effort that have been applied for this technology. As the concept is new, finding the suitable material related to the subject matter was the challenge for this project. The objective was completed by condu...

  4. Magnetic fusion technology

    CERN Document Server

    Dolan, Thomas J

    2014-01-01

    Magnetic Fusion Technology describes the technologies that are required for successful development of nuclear fusion power plants using strong magnetic fields. These technologies include: ? magnet systems, ? plasma heating systems, ? control systems, ? energy conversion systems, ? advanced materials development, ? vacuum systems, ? cryogenic systems, ? plasma diagnostics, ? safety systems, and ? power plant design studies. Magnetic Fusion Technology will be useful to students and to specialists working in energy research.

  5. New Mobile Technologies

    DEFF Research Database (Denmark)

    Tan, Su-En; Henten, Anders

    2006-01-01

    This paper takes a look at Clayton Christensen 's theory of disruptive technologies and how Christensen's theory relates to other innovation theories. It also proposes a new layer of analysis to this theory to better link the technology analysis to the market analysis of any given technology...... product. This layer suggests that complementarity and substitutability are important criteria for technologies to be market disruptions or sustaining changes....

  6. NASA Astrophysics Technology Needs

    Science.gov (United States)

    Stahl, H. Philip

    2012-01-01

    July 2010, NASA Office of Chief Technologist (OCT) initiated an activity to create and maintain a NASA integrated roadmap for 15 key technology areas which recommend an overall technology investment strategy and prioritize NASA?s technology programs to meet NASA?s strategic goals. Science Instruments, Observatories and Sensor Systems(SIOSS) roadmap addresses technology needs to achieve NASA?s highest priority objectives -- not only for the Science Mission Directorate (SMD), but for all of NASA.

  7. Photon technology. Laser processing technology; Photon technology. Laser process gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    Survey has been conducted to develop laser processing technology utilizing the interaction between substance and photon. This is a part of the leading research on photon technology development. The photon technology development is aimed at novel technology development highly utilizing the quantum nature of photons. In the field of laser processing, high quality photons are used as tools, special functions of atoms and molecules will be discovered, and processing for functional fabrication (photon machining) will be established. A role of laser processing in industries has become significant, which is currently spreading not only into cutting and welding of materials and scalpels but also into such a special field as ultrafine processing of materials. The spreading is sometimes obstructed due to the difficulty of procurement of suitable machines and materials, and the increase of cost. The purpose of this study is to develop the optimal laser technology, to elucidate the interaction between substance and photon, and to develop the laser system and the transmission and regulation systems which realize the optimal conditions. 387 refs., 115 figs., 25 tabs.

  8. Photon technology. Hard photon technology; Photon technology. Hard photon gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    For the application of photon to industrial technologies, in particular, a hard photon technology was surveyed which uses photon beams of 0.1-200nm in wavelength. Its features such as selective atom reaction, dense inner shell excitation and spacial high resolution by quantum energy are expected to provide innovative techniques for various field such as fine machining, material synthesis and advanced inspection technology. This wavelength region has been hardly utilized for industrial fields because of poor development of suitable photon sources and optical devices. The developmental meaning, usable time and issue of a hard photon reduction lithography were surveyed as lithography in ultra-fine region below 0.1{mu}m. On hard photon analysis/evaluation technology, the industrial use of analysis, measurement and evaluation technologies by micro-beam was viewed, and optimum photon sources and optical systems were surveyed. Prediction of surface and surface layer modification by inner shell excitation, the future trend of this process and development of a vacuum ultraviolet light source were also surveyed. 383 refs., 153 figs., 17 tabs.

  9. Enhancing Teaching with Technology.

    Science.gov (United States)

    Pedras, Melvin J.; Oaks, Merrill

    Students who are not educated in the modern advances of our technological society will be ill-prepared for the world of work in the 21st century. It is therefore incumbent upon all educators to modify traditional curriculum to reflect contemporary technology. School technology education programs today are being developed to reflect the needs of…

  10. Conducting a Technology Audit

    Science.gov (United States)

    Flaherty, William

    2011-01-01

    Technology is a critical component in the success of any high-functioning school district, thus it is important that education leaders should examine it closely. Simply put, the purpose of a technology audit is to assess the effectiveness of the technology for administrative or instructional use. Rogers Public Schools in Rogers, Arkansas, recently…

  11. Moralizing Food Technology

    DEFF Research Database (Denmark)

    Coff, Christian Eyde

    2015-01-01

    Food technologies are common on many levels in society and used by both food professionals and consumers. Food technologies are not neutral. They inform and shape the behaviour of people. This paper presents a theoretical framework for analysing the mediating role of food technology and its influ...

  12. The Human Technology

    DEFF Research Database (Denmark)

    Fausing, Bent

    with fundamental human values like intuition, vision and sensing; all the qualities the technology, the industrialisation and rationalisation, or in short modernity, has been criticized for having taken away from human existence. What technology has taken away now comes back through new technology as an aid...

  13. Technological Style is History

    DEFF Research Database (Denmark)

    Blond, Lasse

    The effort to comprehend innovation across cultures and time highlights the importance of the explicating factors external to technology. It becomes relevant to nuance or differentiate the understanding of social and cultural responses to adopted technologies by recognizing that technology shapes...

  14. Advanced manufacturing: Technology diffusion

    Energy Technology Data Exchange (ETDEWEB)

    Tesar, A.

    1995-12-01

    In this paper we examine how manufacturing technology diffuses rom the developers of technology across national borders to those who do not have the capability or resources to develop advanced technology on their own. None of the wide variety of technology diffusion mechanisms discussed in this paper are new, yet the opportunities to apply these mechanisms are growing. A dramatic increase in technology diffusion occurred over the last decade. The two major trends which probably drive this increase are a worldwide inclination towards ``freer`` markets and diminishing isolation. Technology is most rapidly diffusing from the US In fact, the US is supplying technology for the rest of the world. The value of the technology supplied by the US more than doubled from 1985 to 1992 (see the Introduction for details). History shows us that technology diffusion is inevitable. It is the rates at which technologies diffuse to other countries which can vary considerably. Manufacturers in these countries are increasingly able to absorb technology. Their manufacturing efficiency is expected to progress as technology becomes increasingly available and utilized.

  15. Appropriate technology directories

    Energy Technology Data Exchange (ETDEWEB)

    Frankena, F.

    1984-01-01

    An alphabetical and annotated list of 107 directories of appropriate technologies includes the publications of numerous small firms and residential groups as well as government and industry sources. The references cover neighborhood, village, and community efforts to develop decentralized technologies. Some list private and public funding sources, while others deal with legal, technical, and social aspects of renewable and alternative technologies.

  16. Stretching Your Technology Dollar

    Science.gov (United States)

    Johnson, Doug

    2012-01-01

    A school district technology director offers 10 strategies to help schools make the most of their technology dollar. These include using effective budgeting techniques, taking advantage of the buying power of groups, practicing sustainable technology, purchasing the right tool for the right job, taking advantage of free software, using cloud…

  17. Technology in Education

    Science.gov (United States)

    Roden, Kasi

    2011-01-01

    This paper was written to support a position on using technology in education. The purpose of this study was to support the use of technology in education by synthesizing previous research. A variety of sources including books and journal articles were studied in order to compile an overview of the benefits of using technology in elementary,…

  18. Teaching Information Technology Law

    Science.gov (United States)

    Taylor, M. J.; Jones, R. P.; Haggerty, J.; Gresty, D.

    2009-01-01

    In this paper we discuss an approach to the teaching of information technology law to higher education computing students that attempts to prepare them for professional computing practice. As information technology has become ubiquitous its interactions with the law have become more numerous. Information technology practitioners, and in particular…

  19. Creative Technology and Rap

    Science.gov (United States)

    Ch'ien, Evelyn

    2011-01-01

    This paper describes how a linguistic form, rap, can evolve in tandem with technological advances and manifest human-machine creativity. Rather than assuming that the interplay between machines and technology makes humans robotic or machine-like, the paper explores how the pressure of executing artistic visions using technology can drive…

  20. Biometric technology overview

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    Biometrics was identified as one amongst 10 emerging technologies which would change the world in the twenty-first century. Components and processes of biometric system and the relevant technologies are explained in this article. Examples of biometric applications and trends of biometric research, together with industry development,are introduced, which illustrate the challenges and opportunities of this technology.

  1. Technology or Process First?

    DEFF Research Database (Denmark)

    Siurdyban, Artur Henryk; Svejvig, Per; Møller, Charles

    between them using strategic alignment, Enterprise Systems and Business Process Management theories. We argue that the insights from these cases can lead to a better alignment between process and technology. Implications for practice include the direction towards a closer integration of process...... and technology factors in organizations. Theoretical implications call for a design-oriented view of technology and process alignment....

  2. New Technologies in Mathematics.

    Science.gov (United States)

    Sarmiento, Jorge

    An understanding of past technological advancements can help educators understand the influence of new technologies in education. Inventions such as the abacus, logarithms, the slide rule, the calculating machine, computers, and electronic calculators have all found their place in mathematics education. While new technologies can be very useful,…

  3. Mineral Processing Technology Roadmap

    Energy Technology Data Exchange (ETDEWEB)

    none,

    2000-09-01

    This document represents the roadmap for Processing Technology Research in the US Mining Industry. It was developed based on the results of a Processing Technology Roadmap Workshop sponsored by the National Mining Association in conjunction with the US Department of Energy, Office of Energy Efficiency and Renewable Energy, Office of Industrial Technologies. The Workshop was held January 24 - 25, 2000.

  4. Sharing Science and Technology.

    Science.gov (United States)

    Morgan, Robert P.

    1983-01-01

    Defining development as some combination of improving the standard of living and quality of life, meeting basic needs, and increasing per capita gross national product, this article discusses the role science and technology can play in developing countries. Considers technology transfer, appropriate technology, and other issues. (JN)

  5. Stretching Your Technology Dollar

    Science.gov (United States)

    Johnson, Doug

    2012-01-01

    A school district technology director offers 10 strategies to help schools make the most of their technology dollar. These include using effective budgeting techniques, taking advantage of the buying power of groups, practicing sustainable technology, purchasing the right tool for the right job, taking advantage of free software, using cloud…

  6. Selecting Security Technology Providers

    Science.gov (United States)

    Schneider, Tod

    2009-01-01

    The world of security technology holds great promise, but it is fraught with opportunities for expensive missteps and misapplications. The quality of the security technology consultants and system integrators one uses will have a direct bearing on how well his school masters this complex subject. Security technology consultants help determine…

  7. Teaching with Technology

    Science.gov (United States)

    Attard, Catherine

    2011-01-01

    New technologies continue to change every aspect of home, life and work: the way people communicate, calculate, analyse, shop, make presentations and socialise. "The Australian Curriculum" acknowledges the importance of teaching and learning with technology by including the use of information and communication technology (ICT) as one of…

  8. Education Technology Success Stories

    Science.gov (United States)

    West, Darrell M.; Bleiberg, Joshua

    2013-01-01

    Advances in technology are enabling dramatic changes in education content, delivery, and accessibility. Throughout history, new technologies have facilitated the exponential growth of human knowledge. In the early twentieth century, the focus was on the use of radios in education. But since then, innovators have seen technology as a way to improve…

  9. Creative Technology and Rap

    Science.gov (United States)

    Ch'ien, Evelyn

    2011-01-01

    This paper describes how a linguistic form, rap, can evolve in tandem with technological advances and manifest human-machine creativity. Rather than assuming that the interplay between machines and technology makes humans robotic or machine-like, the paper explores how the pressure of executing artistic visions using technology can drive…

  10. Technology Assessment Report: Aqueous Sludge Gasification Technologies

    Science.gov (United States)

    The study reveals that sludge gasification is a potentially suitable alternative to conventional sludge handling and disposal methods. However, very few commercial operations are in existence. The limited pilot, demonstration or commercial application of gasification technology t...

  11. Technology Matters - When new technology reshape innovation

    DEFF Research Database (Denmark)

    Edwards, Kasper; Pedersen, Jørgen Lindgaard

    2004-01-01

    Management of innovation is an important issue for firms and being good at this may be the deciding difference between death and survival. This paper ar-gues, based on 12 case studies, that new technology influence the innovative ca-pability of firms and disturbingly the process appears...... the firm, which over time becomes a source of innovation. However, through adoption of this new technology firms engage in a mu-tual learning and forming process where the firm learn by using the new technol-ogy. When learning, the firm and the new technology is mutually formed as the firm tries to adopt...... not to be managed in the sense that aims, instruments and resources are unclear. It is observed that new technology is adopted with a limited scope and fo-cus – often to solve a particular technical problem e.g. the quality of specifica-tion are too low. For a single reason a new technology is introduced within...

  12. Applied Semantic Web Technologies

    CERN Document Server

    Sugumaran, Vijayan

    2011-01-01

    The rapid advancement of semantic web technologies, along with the fact that they are at various levels of maturity, has left many practitioners confused about the current state of these technologies. Focusing on the most mature technologies, Applied Semantic Web Technologies integrates theory with case studies to illustrate the history, current state, and future direction of the semantic web. It maintains an emphasis on real-world applications and examines the technical and practical issues related to the use of semantic technologies in intelligent information management. The book starts with

  13. Technology reviews: Glazing systems

    Energy Technology Data Exchange (ETDEWEB)

    Schuman, J.; Rubinstein, F.; Papamichael, K.; Beltran, L.; Lee, E.S.; Selkowitz, S.

    1992-09-01

    We present a representative review of existing, emerging, and future technology options in each of five hardware and systems areas in envelope and lighting technologies: lighting systems, glazing systems, shading systems, daylighting optical systems, and dynamic curtain wall systems. The term technology is used here to describe any design choice for energy efficiency, ranging from individual components to more complex systems to general design strategies. The purpose of this task is to characterize the state of the art in envelope and lighting technologies in order to identify those with promise for advanced integrated systems, with an emphasis on California commercial buildings. For each technology category, the following activities have been attempted to the extent possible: Identify key performance characteristics and criteria for each technology; determine the performance range of available technologies; identify the most promising technologies and promising trends in technology advances; examine market forces and market trends; and develop a continuously growing in-house database to be used throughout the project. A variety of information sources have been used in these technology characterizations, including miscellaneous periodicals, manufacturer catalogs and cut sheets, other research documents, and data from previous computer simulations. We include these different sources in order to best show the type and variety of data available, however publication here does not imply our guarantee of these data. Within each category, several broad classes are identified, and within each class we examine the generic individual technologies that fag into that class.

  14. Technology reviews: Shading systems

    Energy Technology Data Exchange (ETDEWEB)

    Schuman, J.; Rubinstein, F.; Papamichael, K.; Beltran, L.; Lee, E.S.; Selkowitz, S.

    1992-09-01

    We present a representative review of existing, emerging, and future technology options in each of five hardware and systems areas in envelope and lighting technologies: lighting systems, glazing systems, shading systems, daylighting optical systems, and dynamic curtain wall systems. The term technology is used here to describe any design choice for energy efficiency, ranging from individual components to more complex systems to general design strategies. The purpose of this task is to characterize the state of the art in envelope and lighting technologies in order to identify those with promise for advanced integrated systems, with an emphasis on California commercial buildings. For each technology category, the following activities have been attempted to the extent possible: Identify key performance characteristics and criteria for each technology. Determine the performance range of available technologies. Identify the most promising technologies and promising trends in technology advances. Examine market forces and market trends. Develop a continuously growing in-house database to be used throughout the project. A variety of information sources have been used in these technology characterizations, including miscellaneous periodicals, manufacturer catalogs and cut sheets, other research documents, and data from previous computer simulations. We include these different sources in order to best show the type and variety of data available, however publication here does not imply our guarantee of these data. Within each category, several broad classes are identified, and within each class we examine the generic individual technologies that fall into that class.

  15. Technology-Use Mediation

    DEFF Research Database (Denmark)

    Bansler, Jørgen P.; Havn, Erling C.

    2003-01-01

    This study analyzes how a group of ‘mediators’ in a large, multinational company adapted a computer-mediated communication technology (a ‘virtual workspace’) to the organizational context (and vice versa) by modifying features of the technology, providing ongoing support for users, and promoting...... of technology-use mediation is more complex and indeterminate than earlier literature suggests. In particular, we want to draw attention to the fact that advanced computer-mediated communication technologies are equivocal and that technology-use mediation consequently requires ongoing sensemaking (Weick 1995)....... appropriate conventions of use. Our findings corroborate earlier research on technology-use mediation, which suggests that such mediators can exert considerable influence on how a particular technology will be established and used in an organization. However, this study also indicates that the process...

  16. Technology and Global Change

    Science.gov (United States)

    Grübler, Arnulf

    2003-10-01

    Technology and Global Change describes how technology has shaped society and the environment over the last 200 years. Technology has led us from the farm to the factory to the internet, and its impacts are now global. Technology has eliminated many problems, but has added many others (ranging from urban smog to the ozone hole to global warming). This book is the first to give a comprehensive description of the causes and impacts of technological change and how they relate to global environmental change. Written for specialists and nonspecialists alike, it will be useful for researchers and professors, as a textbook for graduate students, for people engaged in long-term policy planning in industry (strategic planning departments) and government (R & D and technology ministries, environment ministries), for environmental activists (NGOs), and for the wider public interested in history, technology, or environmental issues.

  17. Technology Museums in Denmark

    DEFF Research Database (Denmark)

    Søndergaard, Morten Karnøe

    2012-01-01

    This article presents an exhibit review of some of the major technology museums in Denmark. First comes an introduction to the Danish museum ”landscape”. Second a total of six museums and their technology focused exhibits are presented. Among the museums are the Fisheries and Maritime Museum...... in Esbjerg, housing one of the most impressive and representative exhibitions on the technology behind the strong Danish maritime sector. Another museum being mentioned is the Energy Museum, which covers the background for some of the major breakthroughs performed in Denmark within this area; particularly...... within wind power technology. Finally special attention is devoted to the Danish Technological Museum. A museum which is the oldest and most elaborate of all the technology museums. The museum covers virtually every technological breakthrough with any relevance in a Danish section, with a special focus...

  18. Technologies as incarnated action

    DEFF Research Database (Denmark)

    Schraube, Ernst

    Contemporary conceptualizations of technology go beyond the traditional interpretation of created things as simply neutral means to an end. They theorize technologies as objects, which embody regimes of power (the theory of technological politics), or scripts (actor-network theory), or values...... (critical theory of technology), or patriarchal thought structures (feminist theories of technology). As helpful as these theories may be to understand the inner relationship between the technosphere and human life, the way in which the life of the individuals in the world of things is imagined remains...... vague and imprecise. In this paper I will argue for a social theory of technology, which includes the subjective and intersubjective implications of technological artifacts. I will show how acting has shifted from the province of human subjects to the sphere of work and products. The created things now...

  19. Technology Empowerment: Security Challenges.

    Energy Technology Data Exchange (ETDEWEB)

    Warren, Drake Edward [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Backus, George A. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Jones, Wendell [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Nelson, Thomas R. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Skocypec, Russell D. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2017-03-01

    Technology empowerment” means that innovation is increasingly accessible to ordinary people of limited means. As powerful technologies become more affordable and accessible, and as people are increasingly connected around the world, ordinary people are empowered to participate in the process of innovation and share the fruits of collaborative innovation. This annotated briefing describes technology empowerment and focuses on how empowerment may create challenges to U.S. national security. U.S. defense research as a share of global innovation has dwindled in recent years. With technology empowerment, the role of U.S. defense research is likely to shrink even further while technology empowerment will continue to increase the speed of innovation. To avoid falling too far behind potential technology threats to U.S. national security, U.S. national security institutions will need to adopt many of the tools of technology empowerment.

  20. JPRS Report, Science & Technology, Japan

    Science.gov (United States)

    2007-11-02

    This is Japan Report with Science and Technology. It contains the issues with different topics on biotecnology , defense industry, nuclear engineering, Marine technology, science and technology policy.

  1. Technology '90

    Energy Technology Data Exchange (ETDEWEB)

    1991-01-01

    The US Department of Energy (DOE) laboratories have a long history of excellence in performing research and development in a number of areas, including the basic sciences, applied-energy technology, and weapons-related technology. Although technology transfer has always been an element of DOE and laboratory activities, it has received increasing emphasis in recent years as US industrial competitiveness has eroded and efforts have increased to better utilize the research and development resources the laboratories provide. This document, Technology '90, is the latest in a series that is intended to communicate some of the many opportunities available for US industry and universities to work with the DOE and its laboratories in the vital activity of improving technology transfer to meet national needs. Technology '90 is divided into three sections: Overview, Technologies, and Laboratories. The Overview section describes the activities and accomplishments of the DOE research and development program offices. The Technologies section provides descriptions of new technologies developed at the DOE laboratories. The Laboratories section presents information on the missions, programs, and facilities of each laboratory, along with a name and telephone number of a technology transfer contact for additional information. Separate papers were prepared for appropriate sections of this report.

  2. Technology transfer 1994

    Energy Technology Data Exchange (ETDEWEB)

    1994-01-01

    This document, Technology Transfer 94, is intended to communicate that there are many opportunities available to US industry and academic institutions to work with DOE and its laboratories and facilities in the vital activity of improving technology transfer to meet national needs. It has seven major sections: Introduction, Technology Transfer Activities, Access to Laboratories and Facilities, Laboratories and Facilities, DOE Office, Technologies, and an Index. Technology Transfer Activities highlights DOE`s recent developments in technology transfer and describes plans for the future. Access to Laboratories and Facilities describes the many avenues for cooperative interaction between DOE laboratories or facilities and industry, academia, and other government agencies. Laboratories and Facilities profiles the DOE laboratories and facilities involved in technology transfer and presents information on their missions, programs, expertise, facilities, and equipment, along with data on whom to contact for additional information on technology transfer. DOE Offices summarizes the major research and development programs within DOE. It also contains information on how to access DOE scientific and technical information. Technologies provides descriptions of some of the new technologies developed at DOE laboratories and facilities.

  3. Technology and teen drivers.

    Science.gov (United States)

    Lee, John D

    2007-01-01

    The rapid evolution of computing, communication, and sensor technology is likely to affect young drivers more than others. The distraction potential of infotainment technology stresses the same vulnerabilities that already lead young drivers to crash more frequently than other drivers. Cell phones, text messaging, MP3 players, and other nomadic devices all present a threat because young drivers may lack the spare attentional capacity for vehicle control and the ability to anticipate and manage hazards. Moreover, young drivers are likely to be the first and most aggressive users of new technology. Fortunately, emerging technology can also support safe driving. Electronic stability control, collision avoidance systems, intelligent speed adaptation, and vehicle tracking systems can all help mitigate the threats to young drivers. However, technology alone is unlikely to make young drivers safer. One promising approach to tailoring technology to teen drivers is to extend proven methods for enhancing young driver safety. The success of graduated drivers license programs (GDL) and the impressive safety benefit of supervised driving suggest ways of tailoring technology to the needs of young drivers. To anticipate the effects of technology on teen driving it may be useful to draw an analogy between the effects of passengers and the effects of technology. Technology can act as a teen passenger and undermine safety or it can act as an adult passenger and enhance safety. Rapidly developing technology may have particularly large effects on teen drivers. To maximize the positive effects and minimize the negative effects will require a broad range of industries to work together. Ideally, vehicle manufacturers would work with infotainment providers, insurance companies, and policy makers to craft new technologies so that they accommodate the needs of young drivers. Without such collaboration young drivers will face even greater challenges to their safety as new technologies emerge.

  4. [Earth Science Technology Office's Computational Technologies Project

    Science.gov (United States)

    Fischer, James (Technical Monitor); Merkey, Phillip

    2005-01-01

    This grant supported the effort to characterize the problem domain of the Earth Science Technology Office's Computational Technologies Project, to engage the Beowulf Cluster Computing Community as well as the High Performance Computing Research Community so that we can predict the applicability of said technologies to the scientific community represented by the CT project and formulate long term strategies to provide the computational resources necessary to attain the anticipated scientific objectives of the CT project. Specifically, the goal of the evaluation effort is to use the information gathered over the course of the Round-3 investigations to quantify the trends in scientific expectations, the algorithmic requirements and capabilities of high-performance computers to satisfy this anticipated need.

  5. Technology Transfer and Commercialization

    Science.gov (United States)

    Martin, Katherine; Chapman, Diane; Giffith, Melanie; Molnar, Darwin

    2001-01-01

    During concurrent sessions for Materials and Structures for High Performance and Emissions Reduction, the UEET Intellectual Property Officer and the Technology Commercialization Specialist will discuss the UEET Technology Transfer and Commercialization goals and efforts. This will include a review of the Technology Commercialization Plan for UEET and what UEET personnel are asked to do to further the goals of the Plan. The major goal of the Plan is to define methods for how UEET assets can best be infused into industry. The National Technology Transfer Center will conduct a summary of its efforts in assessing UEET technologies in the areas of materials and emissions reduction for commercial potential. NTTC is assisting us in completing an inventory and prioritization by commercialization potential. This will result in increased exposure of UEET capabilities to the private sector. The session will include audience solicitation of additional commercializable technologies.

  6. Designing Human Technologies

    DEFF Research Database (Denmark)

    Simonsen, Jesper

    and the design process, in ethical and society-related concerns, and in evaluating how designs fulfill needs and solve problems. Designing Human Technologies subscribes to a broad technology concept including information and communication, mobile, environmental/sustainable and energy technologies......, the Humanities, and Social Science. The initiative broadens the perspective of IS and recognize reflections on aesthetics, ethics, values, connections to politics, and strategies for enabling a better future as legitimate parts of the research agenda. Designing Human Technologies is a design-oriented Strategic...... a shared interdisciplinary research and educational collaboration. As a creative research initiative it focuses on change and innovative thinking. The innovativeness is a result of the strongly interdisciplinary perspective which is at the heart of Designing Human Technologies. Designing Human Technologies...

  7. Implementation of Emerging Technologies

    DEFF Research Database (Denmark)

    Barba, F. J.; Orlien, Vibeke; Mota, Maria J.

    2016-01-01

    resources. Lastly, studies with specific examples of the implementation of these novel processing technologies in food industry are described, focusing on the application of high-pressure processing and pulsed electric fields to orange juice, milk, and oysters. Higher implementation costs were observed...... for the emerging processing technologies compared to the conventional processing technologies, which can be explained by the fact that the industrial application of these novel technologies is still under development. In the future the costs are expected to reduce with further technology advances......Novel processing technologies have been gaining interest among food researchers due to their lower impact on nutritional and sensory properties of the products compared to the conventional thermal techniques. In this chapter some of the most well-studied (eg, high-pressure processing, pulsed...

  8. Sensor technology foresight

    DEFF Research Database (Denmark)

    Andersen, Per Dannemand; Jørgensen, Birte Holst; Rasmussen, Birgitte

    2001-01-01

    The Sensor Technology Center A/S (STC) in co-operation with Risoe National Laboratory has carried out a sensor technology foresight in order to strengthen a strategic outlook on sensor technology. The technology foresight (with a timeframe of 2000 to2015) has been performed in the period October...... 2000 - September 2001. The conclusions of the sensor technology report are based on 1) a scanning of existing forward looking literature on sensor technology, 2) a number of workshops with Danish andinternational participants and 3) an international survey with 174 respondents. Half of the respondents...... came from universities and other research institutes, and approximately one-third came from industry. The study has analysed six types of sensors(covering 13 sub-types) and, in addition, a number of systemic issues. All three sources of information indicate the same pattern regarding future...

  9. Technology Transfer and Commercialization

    Science.gov (United States)

    Martin, Katherine; Chapman, Diane; Giffith, Melanie; Molnar, Darwin

    2001-01-01

    During concurrent sessions for Materials and Structures for High Performance and Emissions Reduction, the UEET Intellectual Property Officer and the Technology Commercialization Specialist will discuss the UEET Technology Transfer and Commercialization goals and efforts. This will include a review of the Technology Commercialization Plan for UEET and what UEET personnel are asked to do to further the goals of the Plan. The major goal of the Plan is to define methods for how UEET assets can best be infused into industry. The National Technology Transfer Center will conduct a summary of its efforts in assessing UEET technologies in the areas of materials and emissions reduction for commercial potential. NTTC is assisting us in completing an inventory and prioritization by commercialization potential. This will result in increased exposure of UEET capabilities to the private sector. The session will include audience solicitation of additional commercializable technologies.

  10. Geothermal innovative technologies catalog

    Energy Technology Data Exchange (ETDEWEB)

    Kenkeremath, D. (ed.)

    1988-09-01

    The technology items in this report were selected on the basis of technological readiness and applicability to current technology transfer thrusts. The items include technologies that are considered to be within 2 to 3 years of being transferred. While the catalog does not profess to be entirely complete, it does represent an initial attempt at archiving innovative geothermal technologies with ample room for additions as they occur. The catalog itself is divided into five major functional areas: Exploration; Drilling, Well Completion, and Reservoir Production; Materials and Brine Chemistry; Direct Use; and Economics. Within these major divisions are sub-categories identifying specific types of technological advances: Hardware; Software; Data Base; Process/Procedure; Test Facility; and Handbook.

  11. Information Technology Resources Assessment

    Energy Technology Data Exchange (ETDEWEB)

    1993-04-01

    The Information Technology Resources Assessment (ITRA) is being published as a companion document to the Department of Energy (DOE) FY 1994--FY 1998 Information Resources Management Long-Range Plan. This document represents a collaborative effort between the Office of Information Resources Management and the Office of Energy Research that was undertaken to achieve, in part, the Technology Strategic Objective of IRM Vision 21. An integral part of this objective, technology forecasting provides an understanding of the information technology horizon and presents a perspective and focus on technologies of particular interest to DOE program activities. Specifically, this document provides site planners with an overview of the status and use of new information technology for their planning consideration.

  12. NAND flash memory technologies

    CERN Document Server

    Aritome, Seiichi

    2016-01-01

    This book discusses basic and advanced NAND flash memory technologies, including the principle of NAND flash, memory cell technologies, multi-bits cell technologies, scaling challenges of memory cell, reliability, and 3-dimensional cell as the future technology. Chapter 1 describes the background and early history of NAND flash. The basic device structures and operations are described in Chapter 2. Next, the author discusses the memory cell technologies focused on scaling in Chapter 3, and introduces the advanced operations for multi-level cells in Chapter 4. The physical limitations for scaling are examined in Chapter 5, and Chapter 6 describes the reliability of NAND flash memory. Chapter 7 examines 3-dimensional (3D) NAND flash memory cells and discusses the pros and cons in structure, process, operations, scalability, and performance. In Chapter 8, challenges of 3D NAND flash memory are dis ussed. Finally, in Chapter 9, the author summarizes and describes the prospect of technologies and market for the fu...

  13. Emerging and Disruptive Technologies

    Science.gov (United States)

    2016-01-01

    Several emerging or disruptive technologies can be identified that might, at some point in the future, displace established laboratory medicine technologies and practices. These include increased automation in the form of robots, 3-D printing, technology convergence (e.g., plug-in glucose meters for smart phones), new point-of-care technologies (e.g., contact lenses with sensors, digital and wireless enabled pregnancy tests) and testing locations (e.g., Retail Health Clinics, new at-home testing formats), new types of specimens (e.g., cell free DNA), big biology/data (e.g., million genome projects), and new regulations (e.g., for laboratory developed tests). In addition, there are many emerging technologies (e.g., planar arrays, mass spectrometry) that might find even broader application in the future and therefore also disrupt current practice. One interesting source of disruptive technology may prove to be the Qualcomm Tricorder XPrize, currently in its final stages. PMID:27683538

  14. Wibree: wireless communication technology

    Science.gov (United States)

    Fernandes e Fizardo, Trima Piedade

    2011-12-01

    Nowadays everywhere we come across electronic devices and now the world has become entirely mobile with so many new electronic equipments. The number of computing and telecommunications devices is increasing and consequently the focus on how to connect them to each other. The usual solution is to connect the device with cables or using infra red light to make file transfer and synchronizations possible but infrared light requires line of sight. To solve these problems a new technology,Wibree radio technology complements other local connectivity technologies, consuming only a fraction of the power compared to other radio technologies, enabling smaller and less costly implementations and being easy to integrate with Bluetooth solutions, Furthermore it can be also used to enable communication between several units such as small radio LANs.This paper focuses on why this technology has got large attention although there are pro's and con's with respect to other technologies.

  15. Emerging and Disruptive Technologies.

    Science.gov (United States)

    Kricka, Larry J

    2016-08-01

    Several emerging or disruptive technologies can be identified that might, at some point in the future, displace established laboratory medicine technologies and practices. These include increased automation in the form of robots, 3-D printing, technology convergence (e.g., plug-in glucose meters for smart phones), new point-of-care technologies (e.g., contact lenses with sensors, digital and wireless enabled pregnancy tests) and testing locations (e.g., Retail Health Clinics, new at-home testing formats), new types of specimens (e.g., cell free DNA), big biology/data (e.g., million genome projects), and new regulations (e.g., for laboratory developed tests). In addition, there are many emerging technologies (e.g., planar arrays, mass spectrometry) that might find even broader application in the future and therefore also disrupt current practice. One interesting source of disruptive technology may prove to be the Qualcomm Tricorder XPrize, currently in its final stages.

  16. Wireless communication technology NFC

    OpenAIRE

    MÁROVÁ, Kateřina

    2014-01-01

    Aim of this bachelor thesis is to handle the issue of new wireless communication technology NFC (Near Field Communication) including a comparison of advantages and disadvantages of NFC with other wireless technologies (Bluetooth, Wi-Fi, etc.). NFC is a technology for wireless communications between different electronic devices, one of which is typically a mobile phone. Near Field Communication allows wireless communication at very short distance by approaching or enclosing two devices and can...

  17. Digital Sensor Technology

    Energy Technology Data Exchange (ETDEWEB)

    Ted Quinn; Jerry Mauck; Richard Bockhorst; Ken Thomas

    2013-07-01

    The nuclear industry has been slow to incorporate digital sensor technology into nuclear plant designs due to concerns with digital qualification issues. However, the benefits of digital sensor technology for nuclear plant instrumentation are substantial in terms of accuracy, reliability, availability, and maintainability. This report demonstrates these benefits in direct comparisons of digital and analog sensor applications. It also addresses the qualification issues that must be addressed in the application of digital sensor technology.

  18. SNP genotyping technologies

    DEFF Research Database (Denmark)

    Studer, Bruno; Kölliker, Roland

    2013-01-01

    for this is the availability of high-throughput platforms for multiplexed SNP genotyping. Advancements in these technologies have enabled increased flexibility and throughput, allowing for the generation of adequate SNP marker data at very competitive cost per data point.......In the recent years, single nucleotide polymorphism (SNP) markers have emerged as the marker technology of choice for plant genetics and breeding applications. Besides the efficient technologies available for SNP discovery even in complex genomes, one of the main reasons...

  19. SNP genotyping technologies

    DEFF Research Database (Denmark)

    Studer, Bruno; Kölliker, Roland

    2013-01-01

    In the recent years, single nucleotide polymorphism (SNP) markers have emerged as the marker technology of choice for plant genetics and breeding applications. Besides the efficient technologies available for SNP discovery even in complex genomes, one of the main reasons...... for this is the availability of high-throughput platforms for multiplexed SNP genotyping. Advancements in these technologies have enabled increased flexibility and throughput, allowing for the generation of adequate SNP marker data at very competitive cost per data point....

  20. Software Architecture Technology Initiative

    Science.gov (United States)

    2008-04-01

    2008 Carnegie Mellon University 2008 PLS March 2008 © 2008 Carnegie Mellon University Software Architecture Technology Initiative SATURN 2008...SUBTITLE Software Architecture Technology Initiative 5a. CONTRACT NUMBER 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 6. AUTHOR(S) 5d. PROJECT...SUPPLEMENTARY NOTES presented at the SEI Software Architecture Technology User Network (SATURN) Workshop, 30 Apr ? 1 May 2008, Pittsburgh, PA. 14

  1. Software Partitioning Technologies

    Science.gov (United States)

    2001-05-29

    1 Software Partitioning Technologies Tim Skutt Smiths Aerospace 3290 Patterson Ave. SE Grand Rapids, MI 49512-1991 (616) 241-8645 skutt_timothy...Limitation of Abstract UU Number of Pages 12 2 Agenda n Software Partitioning Overview n Smiths Software Partitioning Technology n Software Partitioning...Partition Level OS Core Module Level OS Timers MMU I/O API Layer Partitioning Services 6 Smiths Software Partitioning Technology n Smiths has developed

  2. Trends in Technology Use

    OpenAIRE

    Florin Frant

    2009-01-01

    This study aims to investigate the relationship between the use of technology, working conditions and the health and well-being of workers in Europe. As it is known that characteristics of work organisation may reinforce or impair both positive and negative effects of technology use, the role of these characteristics is also considered in this study. The research will provide an insight into the trends and changes in technology use and working conditions in European count...

  3. Mixed plastics recycling technology

    CERN Document Server

    Hegberg, Bruce

    1995-01-01

    Presents an overview of mixed plastics recycling technology. In addition, it characterizes mixed plastics wastes and describes collection methods, costs, and markets for reprocessed plastics products.

  4. Advanced Surface Technology

    DEFF Research Database (Denmark)

    Møller, Per; Nielsen, Lars Pleht

    This new significant book on advanced modern surface technology in all its variations, is aimed at both teaching at engineering schools and practical application in industry. The work covers all the significant aspects of modern surface technology and also describes how new advanced techniques make......, nitriding, carbonitriding, and many other lesser-known thermochemical processes used for solving technological problems. The book is richly illustrated with pictures and figures showing how the technology creates new innovative solutions for industry and how surfaces are becoming integral to the function...

  5. Explosive Technology Group

    Data.gov (United States)

    Federal Laboratory Consortium — The Explosive Technology Group (ETG) provides diverse technical expertise and an agile, integrated approach to solve complex challenges for all classes of energetic...

  6. Active ageing technologies

    DEFF Research Database (Denmark)

    Lassen, Aske Juul

    the elderly. As part of this rearticulation of old age, many new technologies take form. This paper uses a wide concept of technologies (devices, regimes, strategies and ways of doing) and argues that technologies form active aging subjectivities, and on the other hand, that these subjectivities...... ‘sites of active aging’ in Denmark. By presenting three technologies of active aging (billiards at an activity center for elderly persons, dancing tiles for rehabilitation after falls and an online fitness community for elderly persons) the paper suggests that active aging is more than regimes...

  7. World Technology Usage Lags

    OpenAIRE

    Diego A. Comin; Bart Hobijn; Emilie Rovito

    2006-01-01

    We present evidence on the differences in the intensity with which ten major technologies are used in 185 countries across the world. We do so by calculating how many years ago these technologies were used in the U.S. at the same intensity as they are used in the countries in our sample. We denote these time lags as technology usage lags and compare them with lags in real GDP per capita. We find that (i) technology usage lags are large, often comparable to lags in real GDP per capita, (ii) us...

  8. Health care technology assessment

    Science.gov (United States)

    Goodman, Clifford

    1994-12-01

    The role of technology in the cost of health care is a primary issue in current debates concerning national health care reform. The broad scope of studies for understanding technological impacts is known as technology assessment. Technology policy makers can improve their decision making by becoming more aware, and taking greater advantage, of key trends in health care technology assessment (HCTA). HCTA is the systematic evaluation of the properties, impacts, and other attributes of health care technologies, including: technical performance; clinical safety and efficacy/effectiveness; cost-effectiveness and other economic attributes; appropriate circumstances/indications for use; and social, legal, ethical, and political impacts. The main purpose of HCTA is to inform technology-related policy making in health care. Among the important trends in HCTA are: (1) proliferation of HCTA groups in the public and private sectors; (2) higher standards for scientific evidence concerning technologies; (3) methodological development in cost analyses, health-related quality of life measurement, and consolidation of available scientific evidence (e.g., meta-analysis); (4) emphasis on improved data on how well technologies work in routine practice and for traditionally under-represented patient groups; (5) development of priority-setting methods; (6) greater reliance on medical informatics to support and disseminate HCTA findings.

  9. Distributed Energy Technology Laboratory

    Data.gov (United States)

    Federal Laboratory Consortium — The Distributed Energy Technologies Laboratory (DETL) is an extension of the power electronics testing capabilities of the Photovoltaic System Evaluation Laboratory...

  10. Acoustic Technology Laboratory

    Data.gov (United States)

    Federal Laboratory Consortium — This laboratory contains an electro-magnetic worldwide data collection and field measurement capability in the area of acoustic technology. Outfitted by NASA Langley...

  11. Solar Cooker Technological Change

    DEFF Research Database (Denmark)

    Ahmad, Bashir

    1997-01-01

    The challenges which solar cooking technology is facing right now is discussed. Based on a field study in Madras and Gujarat, it is asserted that there is an important incompatibility between the technology and the every day real-life conditions of the "users" of solar cooker. An evaluation report...... on a solar cooker technology in Burkina Faso supports the findings of the study. It is concluded that the users and other important actors have to be incorporated in the technological development process of solar cookers in the future....

  12. SCIENTIFIC AND TECHNOLOGICAL INNOVATION

    Directory of Open Access Journals (Sweden)

    Gabriel I. NASTASE

    2011-11-01

    Full Text Available Today, science and, accordingly, scientific research is widely recognized as the main driving force of production and source of innovation and technology transfer. There are many definitions in this regard that seek to express the concept of scientific research, experimental development (engineering and technical progress. Practically in the developed countries the phenomenon of innovation is being analyzed in relation to the concept of technology transfer, based on the experience and knowledge in science and technology. Innovation has to be addressed systematically, it involving: science, technology, financial and economic principles, management.

  13. Moralizing Food Technology

    DEFF Research Database (Denmark)

    Coff, Christian Eyde

    2015-01-01

    Food technologies are common on many levels in society and used by both food professionals and consumers. Food technologies are not neutral. They inform and shape the behaviour of people. This paper presents a theoretical framework for analysing the mediating role of food technology and its...... influence on food ethics. Post-phenomenology and the idea of a technologically mediated morality are central theoretical approaches. Four elements are included in the analytical framework: perception, interpretation, intentionality, and mediated morality. The framework is applied to two cases; food safety...

  14. Application Technology Research Unit

    Data.gov (United States)

    Federal Laboratory Consortium — To conduct fundamental and developmental research on new and improved application technologies to protect floricultural, nursery, landscape, turf, horticultural, and...

  15. Industrial communication technology handbook

    CERN Document Server

    Zurawski, Richard

    2005-01-01

    The Industrial Communication Technology Handbook focuses on current and newly emerging communication technologies and systems that are evolving in response to the needs of industry and the demands of industry-led consortia and organizations.Organized into two parts, the text first summarizes the basics of data communications and IP networks, then presents a comprehensive overview of the field of industrial communications. This book extensively covers the areas of fieldbus technology, industrial Ethernet and real-time extensions, wireless and mobile technologies in industrial applications, the

  16. Technology Roadmaps: Cement

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2009-07-01

    To support its roadmap work focusing on key technologies for emissions reductions, the International Energy Agency (IEA) also investigated one particular industry: cement. Cement production includes technologies that are both specific to this industry and those that are shared with other industries (e.g., grinding, fuel preparation, combustion, crushing, transport). An industry specific roadmap provides an effective mechanism to bring together several technology options. It outlines the potential for technological advancement for emissions reductions in one industry, as well as potential cross-industry collaboration.

  17. Technology for Boundaries

    DEFF Research Database (Denmark)

    Bødker, Susanne; Kristensen, Jannie Friis; Nielsen, Christina

    2003-01-01

    This paper presents a study of an organisation, which is undergoing a process transforming organisational and technological boundaries. In particular, we shall look at three kinds of boundaries: the work to maintain and change the boundary between the organisation and its customers; boundaries.......After analysing the history and the current boundary work, the paper will propose new technological support for boundary work. In particular the paper will suggest means of supporting boundaries when these are productive and for changing boundaries when this seems more appropriate. In total, flexible technologies...... seem a core issue when dealing with technology for boundaries....

  18. Future Information Technology

    CERN Document Server

    Stojmenovic, Ivan; Choi, Min; Xhafa, Fatos; FutureTech 2013

    2014-01-01

    Future technology information technology stands for all of continuously evolving and converging information technologies, including digital convergence, multimedia convergence, intelligent applications, embedded systems, mobile and wireless communications, bio-inspired computing, grid and cloud computing, semantic web, user experience and HCI, security and trust computing and so on, for satisfying our ever-changing needs. In past twenty five years or so, Information Technology (IT) influenced and changed every aspect of our lives and our cultures. These proceedings foster the dissemination of state-of-the-art research in all future IT areas, including their models, services, and novel applications associated with their utilization.

  19. The Next Technology Revolution - Nano Electronic Technology

    Science.gov (United States)

    Turlik, Iwona

    2004-03-01

    Nanotechnology is a revolutionary engine that will engender enormous changes in a vast majority of today's industries and markets, while potentially creating whole new industries. The impact of nanotechnology is particularly significant in the electronics industry, which is constantly driven by the need for higher performance, increased functionality, smaller size and lower cost. Nanotechnology can influence many of the hundreds of components that are typically assembled to manufacture modern electronic devices. Motorola manufactures electronics for a wide range of industries and communication products. In this presentation, the typical components of a cellular phone are outlined and technology requirements for future products, the customer benefits, and the potential impact of nanotechnology on many of the components are discussed. Technology needs include reliable materials supply, processes for high volume production, experimental and simulation tools, etc. For example, even routine procedures such as failure characterization may require the development of new tools for investigating nano-scale phenomena. Business needs include the development of an effective, high volume supply chain for nano-materials and devices, disruptive product platforms, and visible performance impact on the end consumer. An equally significant long-term industry need is the availability of science and engineering graduates with a multidisciplinary focus and a deep understanding of the fundamentals of nano-technology, that can harness the technology to create revolutionary products.

  20. PCP IMMUMOASSAY TECHNOLOGIES - INNOVATIVE TECHNOLOGY EVALUATION REPORT

    Science.gov (United States)

    Three enzyme-linked immunosorbent assay technologies for pentachlorophenol (PCP) testing in soil and water were evaluated. Penta RISc Test Systems (formerly ENSYS, Inc.), EnviroGard™ PCP Immunoassay Test Kit (Millipore Corp.), and Pentachlorophenol RaPID Assay (formerly Ohmicron ...

  1. Robotics Technology Crosscutting Program. Technology summary

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-06-01

    The Robotics Technology Development Program (RTDP) is a needs-driven effort. A length series of presentations and discussions at DOE sites considered critical to DOE`s Environmental Restoration and Waste Management (EM) Programs resulted in a clear understanding of needed robotics applications toward resolving definitive problems at the sites. A detailed analysis of the resulting robotics needs assessment revealed several common threads running through the sites: Tank Waste Retrieval (TWR), Contaminant Analysis Automation (CAA), Mixed Waste Operations (MWO), and Decontamination and Dismantlement (D and D). The RTDP Group also realized that some of the technology development in these four areas had common (Cross Cutting-CC) needs, for example, computer control and sensor interface protocols. Further, the OTD approach to the Research, Development, Demonstration, Testing, and Evaluation (RDDT and E) process urged an additional organizational breakdown between short-term (1--3 years) and long-term (3--5 years) efforts (Advanced Technology-AT). These factors lead to the formation of the fifth application area for Crosscutting and Advanced Technology (CC and AT) development. The RTDP is thus organized around these application areas -- TWR, CAA, MWO, D and D, and CC and AT -- with the first four developing short-term applied robotics. An RTDP Five-Year Plan was developed for organizing the Program to meet the needs in these application areas.

  2. Biosensor technology: technology push versus market pull.

    Science.gov (United States)

    Luong, John H T; Male, Keith B; Glennon, Jeremy D

    2008-01-01

    Biosensor technology is based on a specific biological recognition element in combination with a transducer for signal processing. Since its inception, biosensors have been expected to play a significant analytical role in medicine, agriculture, food safety, homeland security, environmental and industrial monitoring. However, the commercialization of biosensor technology has significantly lagged behind the research output as reflected by a plethora of publications and patenting activities. The rationale behind the slow and limited technology transfer could be attributed to cost considerations and some key technical barriers. Analytical chemistry has changed considerably, driven by automation, miniaturization, and system integration with high throughput for multiple tasks. Such requirements pose a great challenge in biosensor technology which is often designed to detect one single or a few target analytes. Successful biosensors must be versatile to support interchangeable biorecognition elements, and in addition miniaturization must be feasible to allow automation for parallel sensing with ease of operation at a competitive cost. A significant upfront investment in research and development is a prerequisite in the commercialization of biosensors. The progress in such endeavors is incremental with limited success, thus, the market entry for a new venture is very difficult unless a niche product can be developed with a considerable market volume.

  3. Technology Transfer and Technology Transfer Intermediaries

    Science.gov (United States)

    Bauer, Stephen M.; Flagg, Jennifer L.

    2010-01-01

    A standard and comprehensive model is needed to evaluate and compare technology transfer systems and the stakeholders within these systems. The principle systems considered include federal laboratories, U.S. universities, the rehabilitation engineering research centers (RERCs), and large small business innovation research programs. An earlier…

  4. Emerging Technologies - Capturing Innovation with Technology

    Energy Technology Data Exchange (ETDEWEB)

    None

    2012-12-01

    ET team research results are critical to achieving 50% energy savings across U.S. buildings within the next two decades. The ET team focuses on supporting research, development, and tech-to-market opportunities of high impact technologies, or those that demonstrate potential for achieving significant energy savings cost effectively.

  5. Digital Actuator Technology

    Energy Technology Data Exchange (ETDEWEB)

    Ken Thomas; Ted Quinn; Jerry Mauck; Richard Bockhorst

    2014-09-01

    There are significant developments underway in new types of actuators for power plant active components. Many of these make use of digital technology to provide a wide array of benefits in performance of the actuators and in reduced burden to maintain them. These new product offerings have gained considerable acceptance in use in process plants. In addition, they have been used in conventional power generation very successfully. This technology has been proven to deliver the benefits promised and substantiate the claims of improved performance. The nuclear industry has been reluctant to incorporate digital actuator technology into nuclear plant designs due to concerns due to a number of concerns. These could be summarized as cost, regulatory uncertainty, and a certain comfort factor with legacy analog technology. The replacement opportunity for these types of components represents a decision point for whether to invest in more modern technology that would provide superior operational and maintenance benefits. Yet, the application of digital technology has been problematic for the nuclear industry, due to qualification and regulatory issues. With some notable exceptions, the result has been a continuing reluctance to undertake the risks and uncertainties of implementing digital actuator technology when replacement opportunities present themselves. Rather, utilities would typically prefer to accept the performance limitations of the legacy analog actuator technologies to avoid impacts to project costs and schedules. The purpose of this report is to demonstrate that the benefits of digital actuator technology can be significant in terms of plant performance and that it is worthwhile to address the barriers currently holding back the widespread development and use of this technology. It addresses two important objectives in pursuit of the beneficial use of digital actuator technology for nuclear power plants: 1. To demonstrate the benefits of digital actuator

  6. Technology Catalogue. First edition

    Energy Technology Data Exchange (ETDEWEB)

    1994-02-01

    The Department of Energy`s Office of Environmental Restoration and Waste Management (EM) is responsible for remediating its contaminated sites and managing its waste inventory in a safe and efficient manner. EM`s Office of Technology Development (OTD) supports applied research and demonstration efforts to develop and transfer innovative, cost-effective technologies to its site clean-up and waste management programs within EM`s Office of Environmental Restoration and Office of Waste Management. The purpose of the Technology Catalogue is to provide performance data on OTD-developed technologies to scientists and engineers assessing and recommending technical solutions within the Department`s clean-up and waste management programs, as well as to industry, other federal and state agencies, and the academic community. OTD`s applied research and demonstration activities are conducted in programs referred to as Integrated Demonstrations (IDs) and Integrated Programs (IPs). The IDs test and evaluate.systems, consisting of coupled technologies, at specific sites to address generic problems, such as the sensing, treatment, and disposal of buried waste containers. The IPs support applied research activities in specific applications areas, such as in situ remediation, efficient separations processes, and site characterization. The Technology Catalogue is a means for communicating the status. of the development of these innovative technologies. The FY93 Technology Catalogue features technologies successfully demonstrated in the field through IDs and sufficiently mature to be used in the near-term. Technologies from the following IDs are featured in the FY93 Technology Catalogue: Buried Waste ID (Idaho National Engineering Laboratory, Idaho); Mixed Waste Landfill ID (Sandia National Laboratories, New Mexico); Underground Storage Tank ID (Hanford, Washington); Volatile organic compound (VOC) Arid ID (Richland, Washington); and VOC Non-Arid ID (Savannah River Site, South Carolina).

  7. Technology Applications Team: Applications of aerospace technology

    Science.gov (United States)

    1993-01-01

    Highlights of the Research Triangle Institute (RTI) Applications Team activities over the past quarter are presented in Section 1.0. The Team's progress in fulfilling the requirements of the contract is summarized in Section 2.0. In addition to our market-driven approach to applications project development, RTI has placed increased effort on activities to commercialize technologies developed at NASA Centers. These Technology Commercialization efforts are summarized in Section 3.0. New problem statements prepared by the Team in the reporting period are presented in Section 4.0. The Team's transfer activities for ongoing projects with the NASA Centers are presented in Section 5.0. Section 6.0 summarizes the status of four add-on tasks. Travel for the reporting period is described in Section 7.0. The RTI Team staff and consultants and their project responsibilities are listed in Appendix A. The authors gratefully acknowledge the contributions of many individuals to the RTI Technology Applications Team program. The time and effort contributed by managers, engineers, and scientists throughout NASA were essential to program success. Most important to the program has been a productive working relationship with the NASA Field Center Technology Utilization (TU) Offices. The RTI Team continues to strive for improved effectiveness as a resource to these offices. Industry managers, technical staff, medical researchers, and clinicians have been cooperative and open in their participation. The RTI Team looks forward to continuing expansion of its interaction with U.S. industry to facilitate the transfer of aerospace technology to the private sector.

  8. Emerging wind energy technologies

    DEFF Research Database (Denmark)

    Rasmussen, Flemming; Grivel, Jean-Claude; Faber, Michael Havbro

    2014-01-01

    This chapter will discuss emerging technologies that are expected to continue the development of the wind sector to embrace new markets and to become even more competitive.......This chapter will discuss emerging technologies that are expected to continue the development of the wind sector to embrace new markets and to become even more competitive....

  9. School Security Technologies

    Science.gov (United States)

    Schneider, Tod

    2010-01-01

    Over the past decade electronic security technology has evolved from an exotic possibility into an essential safety consideration. Before resorting to high-tech security solutions, school officials should think carefully about the potential for unintended consequences. Technological fixes may be mismatched to the problems being addressed. They can…

  10. Information technology ethics

    DEFF Research Database (Denmark)

    Hongladarom, Soraj; Ess, Charles

    This book was the first publication to take a genuinely global approach to the diverse ethical issues evoked by Information and Communication Technologies and their possible resolutions. Readers will gain a greater appreciation for the problems and possibilities of genuinely global information...... ethics, which are urgently needed as information and communication technologies continue their exponential growth...

  11. Electron tunnel sensor technology

    Science.gov (United States)

    Waltman, S. B.; Kaiser, W. J.

    1989-01-01

    The recent development of Scanning Tunneling Microscopy technology allows the application of electron tunneling to position detectors for the first time. The vacuum tunnel junction is one of the most sensitive position detection mechanisms available. It is also compact, simple, and requires little power. A prototype accelerometer based on electron tunneling, and other sensor applications of this promising new technology are described.

  12. Technological advances transforming rheumatology

    Science.gov (United States)

    Robinson, William H.; Mao, Rong

    2016-01-01

    Technological advances over the past decade have revolutionized many areas of rheumatology, ranging from diagnosis, prognosis and therapeutic development to the mechanistic understanding of rheumatic diseases. This overview highlights key technological innovations and discusses the major impact that these developments are having on research and clinical practice. PMID:26439404

  13. Technology and Teaching Philosophy

    Science.gov (United States)

    King, Paul C.

    2012-01-01

    This article discusses the challenges faced when integrating new technologies into the classroom. Viewing the experiences of teaching a first year learning community through the lens of the principles of the Reflective Teaching Portfolio, the author looks to answer the question: "How should Technology relate to our Teaching Philosophy?" While a…

  14. Technology and Teaching Philosophy

    Science.gov (United States)

    King, Paul C.

    2012-01-01

    This article discusses the challenges faced when integrating new technologies into the classroom. Viewing the experiences of teaching a first year learning community through the lens of the principles of the Reflective Teaching Portfolio, the author looks to answer the question: "How should Technology relate to our Teaching Philosophy?"…

  15. Danish SDHW Technology

    DEFF Research Database (Denmark)

    Furbo, Simon

    1996-01-01

    The status of Danish technology for solar heating systems for hot water supply as well as R&D work in the field is presented.......The status of Danish technology for solar heating systems for hot water supply as well as R&D work in the field is presented....

  16. Shopping for Technology.

    Science.gov (United States)

    Middleton, James A.; Flores, Alfinio; Knaupp, Jonathan

    1997-01-01

    To avoid underuse, inaccessibility, and obsolescence when choosing, purchasing, and using technology, educators should maximize the number of students sharing machines, build technology into the curriculum, ensure continuous accessibility, network computers, and build physical plant considerations into their purchase plans. A single high-end…

  17. Introducing New Technology

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    The 5th China Fujian Technology and Project Fair (CFTPF) will be held from June 18 to 20 this year. Established in 2003, the CFTPF is one of the most impor - tant fairs for promoting advanced science and technological products for the benefit of Chinese

  18. Technology and sustainability

    NARCIS (Netherlands)

    Kroeze, C.; Boersema, J.J.; Tellegen, E.; Cremers, A.

    2011-01-01

    In ten essays, this book addresses a broad range of issues related to the interplay of sustainability and technology. How do population growth and technology relate to sustainable development? Can globalization be reconciled with sustainable development? Is sustainability a subjective or an

  19. Arts and Technology

    DEFF Research Database (Denmark)

    This book constitutes the thoroughly refereed post-conference proceedings of the Second International Conference on Arts and Technology, ArtsIT 2011, which was held in December 2011 in Esbjerg, Denmark. The 19 revised full papers and the two poster papers cover various topics such as Interaction...... and Art, Music and Performance, and Digital Technology....

  20. Information Technology Initiative (Videorecording),

    Science.gov (United States)

    Physical description: 1 VHS video; col.; sd.; mono.; standard playback sp.; 35:40 mins.; 1/2 in. In this video, Dr. Kurt Fisher, Deputy Director for Information Technology , introduces the Corporate Information Management (CIM) program and explains the following major technical initiatives: reuse/repositories; I-case; data administration; information technology architecture; software process improvement; standards.

  1. Advanced Cell Technology, Inc.

    Science.gov (United States)

    Caldwell, William M

    2007-03-01

    Advanced Cell Technology, Inc. (OTCBB: ACTC) is a biotechnology company applying novel human embryonic stem cell technologies in the emerging field of regenerative medicine. We believe that regenerative medicine has the potential to revolutionize the field by enabling scientists to produce human cells of any kind for use in a wide array of therapies.

  2. Advanced Mirror Technology Development

    Science.gov (United States)

    Stahl, H. Philip

    2017-01-01

    The Advanced Mirror Technology Development (AMTD) project matures critical technologies required to enable ultra-stable 4-m-or-larger monolithic or segmented ultraviolet, optical, and infrared (UVOIR) space telescope primary-mirror assemblies for general astrophysics and ultra-high-contrast observations of exoplanets.

  3. Teaching with Technology

    Science.gov (United States)

    Martineau, Pamela

    2009-01-01

    In an era when technology seems to be changing almost daily, school boards, administrators, and teachers need to revisit their technology policies almost as rapidly, education experts advise. Internet chat rooms, online video games, and other electronic features that once seemed inappropriate for the classroom are proving useful for meeting many…

  4. Assistive Technologies for Reading

    Science.gov (United States)

    Ruffin, Tiece M.

    2012-01-01

    Twenty-first century teachers working with diverse readers are often faced with the question of how to integrate technology in reading instruction that meets the needs of the techno-generation. Are today's teachers equipped with the knowledge of how to effectively use Assistive Technologies (AT) for reading? This position paper discusses AT for…

  5. CSIR Technology Impact 1998

    CSIR Research Space (South Africa)

    CSIR

    1998-01-01

    Full Text Available stream_source_info CSIR Technology Impact 1998.pdf.txt stream_content_type text/plain stream_size 23 Content-Encoding ISO-8859-1 stream_name CSIR Technology Impact 1998.pdf.txt Content-Type text/plain; charset=ISO-8859-1 ...

  6. Technology transfer and learning

    NARCIS (Netherlands)

    Steenhuis, Harm-Jan; Bruijn, de Erik J.

    2002-01-01

    Despite the fact that international technology transfer has been widely studied its management still encounters many difficulties. To fully understand the issues that are relevant to the process of transferring production technology, it is necessary to determine the important factors that influence

  7. Computers: Educational Technology Paradox?

    Science.gov (United States)

    Hashim, Hajah Rugayah Hj.; Mustapha, Wan Narita

    2005-01-01

    As we move further into the new millennium, the need to involve and adapt learners with new technology have been the main aim of many institutions of higher learning in Malaysia. The involvement of the government in huge technology-based projects like the Multimedia Super Corridor Highway (MSC) and one of its flagships, the Smart Schools have…

  8. Use of Payment Technology

    DEFF Research Database (Denmark)

    Xiao, Xiao; Hedman, Jonas; Runnemark, Emma

    2015-01-01

    Drawing on the theory of consumption value, this research-in-progress strives to provide a theoretical explanation of payment technology use by investigating the relationship between consumers’ perceptions of different consumption values associated with a certain payment technology and their choi...... behavior, as well as the debate on moving towards a cashless society....

  9. Riding the Technology Wave.

    Science.gov (United States)

    Malan, Pierre

    This paper presents an overview of information technology development. The first section sets the scene, comparing the first WAN (Wide Area Network) and Intel processor to current technology. The birth of the microcomputer is described in the second section, including historical background on semiconductors, microprocessors, and the microcomputer.…

  10. Wind technology issues

    Energy Technology Data Exchange (ETDEWEB)

    Martinez, Antoni; Prats, Pep [Ecotecnia S.C.C.L., Barcelona (Spain)

    1999-01-01

    The paper focuses on the main trends of the technology behind the present wind energy applications. The technology characteristics and main challenges are analysed. The important links between political decisions and the development to date of wind turbines signal a direction for forecasting future tendencies and the possible technical characteristics of future turbines. (Author)

  11. Arts and Technology

    DEFF Research Database (Denmark)

    This book constitutes the thoroughly refereed post-conference proceedings of the Second International Conference on Arts and Technology, ArtsIT 2011, which was held in December 2011 in Esbjerg, Denmark. The 19 revised full papers and the two poster papers cover various topics such as Interaction...... and Art, Music and Performance, and Digital Technology....

  12. Use of Payment Technology

    DEFF Research Database (Denmark)

    Xiao, Xiao; Hedman, Jonas; Runnemark, Emma

    2015-01-01

    Drawing on the theory of consumption value, this research-in-progress strives to provide a theoretical explanation of payment technology use by investigating the relationship between consumers’ perceptions of different consumption values associated with a certain payment technology and their choi...

  13. Nuclear safeguards technology handbook

    Energy Technology Data Exchange (ETDEWEB)

    1977-12-01

    The purpose of this handbook is to present to United States industrial organizations the Department of Energy's (DOE) Safeguards Technology Program. The roles and missions for safeguards in the U.S. government and application of the DOE technology program to industry safeguards planning are discussed. A guide to sources and products is included. (LK)

  14. Technology and sustainability

    NARCIS (Netherlands)

    Kroeze, C.; Boersema, J.J.; Tellegen, E.; Cremers, A.

    2011-01-01

    In ten essays, this book addresses a broad range of issues related to the interplay of sustainability and technology. How do population growth and technology relate to sustainable development? Can globalization be reconciled with sustainable development? Is sustainability a subjective or an objectiv

  15. Presidents and Technology

    Science.gov (United States)

    Ekman, Richard

    2005-01-01

    Almost everyone on campus today grasps the benefits of easy availability of information technology, but for college presidents, the expectations for information technology have been high from the early days. The grail in futurist dreams has been a machine that "thinks," using a very big base of information to sift evidence, make judgments, and…

  16. Institutionalized Technological Foresight

    DEFF Research Database (Denmark)

    Koch, Christian; Hansen, Hans Henrik; Stissing Jensen, Jens

    2008-01-01

    in the national strategy of coordinating and strengthening policy on research, technology and innovation in one superministry. The paper evaluates the methods, impact and role in policy making of these technological foresights. The particular role of institutionalized public foresight in relation to enterprise...

  17. Technology and Educational Structure

    Science.gov (United States)

    Boocock, Sarane S.

    2012-01-01

    Most current debate on instructional technology is characterized either by grandiose speculation on the salvation of education through automation (without specification of "what" and "how" technological innovations will actually be introduced in specific classroom situations, and how the changes will be financed), or by jargon-filled hairsplitting…

  18. Bridging the Technological Gap.

    Science.gov (United States)

    Lazow, Robert; And Others

    The aim of "Bridging the Technological Gap" (BTG), a federally funded demonstration project, is to use microcomputer technology in the rehabilitation of the psychiatrically disabled. Through the use of a custom designed microcomputer software package, clients receive remediation in areas of specific cognitive and behavioral deficits. The project…

  19. Science and Technology Policy

    DEFF Research Database (Denmark)

    Baark, Erik

    1996-01-01

    This paper examines the status of science and technology in Mongolia, and discusses the policy issues which have emerged with the transition to market economy in recent years.......This paper examines the status of science and technology in Mongolia, and discusses the policy issues which have emerged with the transition to market economy in recent years....

  20. Educational Technology Funding Models

    Science.gov (United States)

    Mark, Amy E.

    2008-01-01

    Library and cross-disciplinary literature all stress the increasing importance of instructional technology in higher education. However, there is a dearth of articles detailing funding for library instructional technology. The bulk of library literature on funding for these projects focuses on one-time grant opportunities and on the architecture…

  1. Advanced Materials Technology

    Science.gov (United States)

    Blankenship, C. P. (Compiler); Teichman, L. A. (Compiler)

    1982-01-01

    Composites, polymer science, metallic materials (aluminum, titanium, and superalloys), materials processing technology, materials durability in the aerospace environment, ceramics, fatigue and fracture mechanics, tribology, and nondestructive evaluation (NDE) are discussed. Research and development activities are introduced to the nonaerospace industry. In order to provide a convenient means to help transfer aerospace technology to the commercial mainstream in a systematic manner.

  2. Graphite technology development plan

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1986-07-01

    This document presents the plan for the graphite technology development required to support the design of the 350 MW(t) Modular HTGR within the US National Gas-Cooled Reactor Program. Besides descriptions of the required technology development, cost estimates, and schedules, the plan also includes the associated design functions and design requirements.

  3. Mechatronics and hybrid technologies

    DEFF Research Database (Denmark)

    2008-01-01

    R&D international contributions to control and design of novel intelligent mechatronic products and solutions with sensor- and actuator technology.......R&D international contributions to control and design of novel intelligent mechatronic products and solutions with sensor- and actuator technology....

  4. Interpretation of Internet technology

    DEFF Research Database (Denmark)

    Madsen, Charlotte Øland

    2001-01-01

    -cognitive competencies of organisations (Rindova & Fombrunn, 1999). The aim is to contribute to the existing technological implementation theory complex by studying the relationships between the elements of the socio-cognitive processes and the resulting interpretations and actions when new technologies are implemented......Research scope: The topic of the research project is to investigate how new internet technologies such as e-trade and customer relation marketing and management are implemented in Danish food processing companies. The aim is to use Weick's (1995) sensemaking concept to analyse the strategic...... processes leading to the use of internet marketing technologies and to investigate how these new technologies are interpreted into the organisation. Investigating the organisational socio-cognitive processes underlying the decision making processes will give further insight into the socio...

  5. MODERN BIOGAS TECHNOLOGIES

    Directory of Open Access Journals (Sweden)

    Yu. I. Sidorov

    2013-02-01

    Full Text Available The modern technical level of biogas technologies is considered, in particular in Ukraine. It is shown that in Ukraine the level of introduction of these technologies remains unsatisfactory. The main reason of such state is absence of the government program of development of sufficiently not profitable biogas industry, which again depends on availability of investment facilities including the state one. On the example of the company’s data Zorg Biogas AG, which is dominant in Ukraine among the foreign ones that offer their products using the technique of the net present value — NPV — it is shown insolvency of functioning of profitable biogas power plants. A conclusion is done about the necessity of orientation on own development in area of biogas technologies, State support and intensive technologies. The world level of modern intensive biogas technologies, in particular the use of the cogeneration plants.

  6. Technology in L1

    DEFF Research Database (Denmark)

    Elf, Nikolaj Frydensbjerg; Hanghøj, Thorkild; Skaar, Håvard

    2015-01-01

    In recent decades, several Scandinavian research projects have had an explicit focus on how technology intervenes in L1 (or so-called Mother Tongue Education) practices in Swedish, Norwegian and Danish educational contexts, and how this may impact on understanding of the subject. There is currently......-of-school literacy practices. A final find-ing is the emphasis on teacher uncertainty regarding how and why to integrate technology within exist-ing paradigms of the subject. This calls for further research on how technology may be justified in L1 practice, including various forms of teacher education....... no systematic overview of the documented possibilities and challenges related to the use of technology in L1. At the same time, there is terminological confusion in use of ‘technology’ and related concepts in L1. Finally, there is a general lack of critical reflection on the relation between technological...

  7. Globalization and Technology

    Directory of Open Access Journals (Sweden)

    Traian-Alexandru Miu

    2016-01-01

    Full Text Available Globalization, very complex phenomenon, involves overcoming the barriers between different states, which allowed the rapid transfer of capital, technology, information, and the "toxins" from one country to another. First, the technology formed the basis of rapid expansion of great ideas promoted by globalization. Undeniable progress in the field of technology and science, has conferred to the man extraordinary powers that have been used most often to the detriment of his spiritual progress. We must not deny that science and technology have brought many benefits to human, and he could expand the knowledge horizon upon the world in which he lives, exploiting information acquired and share them with others. Science and technology must become for postmodern man ways of talk and communion between human and divinity, all to the praise of God and the perfection of the creature.

  8. Art, Technology and Nature

    DEFF Research Database (Denmark)

    Since 1900, the connections between art and technology with nature have become increasingly inextricable. Through a selection of innovative readings by international scholars, this book presents the first investigation of the intersections between art, technology and nature in post-medieval times....... Transdisciplinary in approach, this volume’s 14 essays explore art, technology and nature’s shifting constellations that are discernible at the micro level and as part of a larger chronological pattern. Included are subjects ranging from Renaissance wooden dolls, science in the Italian art academies, and artisanal...... Camilla Skovbjerg Paldam and Jacob Wamberg trace the Kantian heritage of radically separating art and technology, and inserting both at a distance to nature, suggesting this was a transient chapter in history. Thus, they argue, the present renegotiation between art, technology and nature is reminiscent...

  9. Designing Human Technologies

    DEFF Research Database (Denmark)

    Simonsen, Jesper

    and the design process, in ethical and society-related concerns, and in evaluating how designs fulfill needs and solve problems. Designing Human Technologies subscribes to a broad technology concept including information and communication, mobile, environmental/sustainable and energy technologies......, the Humanities, and Social Science. The initiative broadens the perspective of IS and recognize reflections on aesthetics, ethics, values, connections to politics, and strategies for enabling a better future as legitimate parts of the research agenda. Designing Human Technologies is a design-oriented Strategic...... and technologies relating to performances and experiences, urban design, climate adaptation, etc. The research takes a process-oriented and participatory approach and involves interaction between different user interests and designs. It is based on empirical, typical case- and action research-oriented studies...

  10. Introduction to microarray technology.

    Science.gov (United States)

    Dufva, Martin

    2009-01-01

    DNA microarrays can be used for large number of application where high-throughput is needed. The ability to probe a sample for hundred to million different molecules at once has made DNA microarray one of the fastest growing techniques since its introduction about 15 years ago. Microarray technology can be used for large scale genotyping, gene expression profiling, comparative genomic hybridization and resequencing among other applications. Microarray technology is a complex mixture of numerous technology and research fields such as mechanics, microfabrication, chemistry, DNA behaviour, microfluidics, enzymology, optics and bioinformatics. This chapter will give an introduction to each five basic steps in microarray technology that includes fabrication, target preparation, hybridization, detection and data analysis. Basic concepts and nomenclature used in the field of microarray technology and their relationships will also be explained.

  11. NASA priority technologies

    Science.gov (United States)

    Sadin, S. R.; Slone, H. O.

    1983-01-01

    Significant research areas deserving of attention within the NASA Space Research and Technology program are discussed, noting that the program is pursed to strengthen the U.S. technology base, improve low-cost access to space, and to aid in the expanded use of space, including a space station. Study areas being pursued include new Orbiter thermal protection system materials, developing longer-life reusable engines, and providing the technology for orbital transfer vehicle propulsion and aeroassisted braking. Attention is also being given to CFD techniques for entry body and rocket engine design, verifying the feasibility of advanced sensor concepts, defining the technology for large deployable RF antennas, and improving on-board data management systems. Of particular concern is to establish technologies which will enhance and extend a permanent manned presence in space.

  12. Making technology public

    DEFF Research Database (Denmark)

    Winthereik, Brit Ross; Johannsen, Nis; Strand, Dixi Louise

    2008-01-01

    secure the future of the technology and organisation behind it. Research limitations/implications – The paper extends the script metaphor beyond a limited designer-technology-user configuration and argues that scripts in the paraphernalia of technologies also can and should be “de......Purpose – Through an analysis of a demonstration video presenting a new national e-health portal, this paper aims to explore the assumptions and limitations of the concept of “script” and suggests a different approach to analysing the moral order of technology design. Design...... the transformative potential of the portal presentation for reconfiguring relationships between citizens, health care systems, and information and communication technology (ICT). The analysis is guided by Haraway's notion of diffraction. Findings – The analysis demonstrates the particular way in which the user...

  13. Working around technologies

    DEFF Research Database (Denmark)

    Dupret, Katia

    2017-01-01

    in Denmark. The aim and contribution of the study is twofold. First, it attempts to revitalise the discussion on technology workaround strategies as responsible professionalism. Second, it will direct attention to and contribute to an understanding of how the normativity embedded in technological development......This study discusses how professionalism and work ethics influence how health care professionals work around new technologies. When people avoid using technologies, they are not necessarily ceasing to engage in their work activities. The workaround strategies presented here are rather practical...... expressions of professionals’ active encounter with the complexity of work situations, and can therefore be important signs of professional ethical judgement. Drawing on science and technology studies and the concept of invisible work, the study discusses workaround situations that arise in health care work...

  14. Communication technology update and fundamentals

    CERN Document Server

    Grant, August E

    2010-01-01

    New communication technologies are being introduced at an astonishing rate. Making sense of these technologies is increasingly difficult. Communication Technology Update and Fundamentals is the single best source for the latest developments, trends, and issues in communication technology. Featuring the fundamental framework along with the history and background of communication technologies, Communication Technology Update and Fundamentals, 12th edition helps you stay ahead of these ever-changing and emerging technologies.As always, every chapter ha

  15. The technology vicinity: a location based view on technology

    NARCIS (Netherlands)

    Steenhuis, H.J.; de Bruijn, E.J.; Kocaoglu, D.F.; Anderson, T.R.

    2001-01-01

    The issue of technology transfer has been viewed from many different perspectives. In this case the focus is on the process of (production) technology transfer. One of the difficulties in studying international technology transfer is the definition of technology. The many technology definitions that

  16. Robotics Technology Development Program. Technology summary

    Energy Technology Data Exchange (ETDEWEB)

    1994-02-01

    The Robotics Technology Development Program (RTDP) is a ``needs-driven`` effort. A lengthy series of presentations and discussions at DOE sites considered critical to DOE`s Environmental Restoration and Waste Management (EM) Programs resulted in a clear understanding of needed robotics applications toward resolving definitive problems at the sites. A detailed analysis of the Tank Waste Retrieval (TWR), Contaminant Analysis Automation (CAA), Mixed Waste Operations (MWO), and Decontamination & Dismantlement (D&D). The RTDP Group realized that much of the technology development was common (Cross Cutting-CC) to each of these robotics application areas, for example, computer control and sensor interface protocols. Further, the OTD approach to the Research, Development, Demonstration, Testing, and Evaluation (RDDT&E) process urged an additional organizational break-out between short-term (1--3 years) and long-term (3--5 years) efforts (Advanced Technology-AT). The RDTP is thus organized around these application areas -- TWR, CAA, MWO, D&D and CC&AT -- with the first four developing short-term applied robotics. An RTDP Five-Year Plan was developed for organizing the Program to meet the needs in these application areas.

  17. Flexibility of MIP Technology

    Institute of Scientific and Technical Information of China (English)

    Tang Jinlian; Gong Jianhong; Xu Youhao

    2015-01-01

    The lfexibility of MIP technology to meet market demand is mainly introduced in this study. Their commercial application and technical principle are analyzed too. The MIP technology with wide feed adaptability can form a good com-bination with other technologies. The MIP technology has been applied extensively in China. Based on this platform, the CGP, MIP-LTG and MIP-DCR technologies have been developed, which can further improve the lfexibility of MIP tech-nology. Based on its novel reaction control technique with a sole sequential two-zone riser, the MIP users can easily switch to different operating modes between producing either more clean gasoline and propylene or diesel through changing the catalysts and varying the operating conditions. That offers MIP users with enough production lfexibility and a rational pro-duction arrangement to meet the market demand. The MIP-DCR technology with less dry gas and coke yields can provide a more lfexible operating mode since the catalysts to oil ratio has become an independent variable.

  18. Technology and medicine.

    Science.gov (United States)

    Booth, C

    1985-05-22

    Technology, which is older than science, has been of vital importance in the development of modern medicine. Even so, there are voices of dissent to be heard. The disenchantment with technology expressed by Aldous Huxley in Brave new world has been echoed by contemporary writers on the technology of modern medicine. Medicine is seen by some to have been dehumanized by technology, and techniques that are expensive are thought to be consuming a greater proportion of health resources than they deserve. The practice of medicine has, nevertheless, been transformed by modern technology and diagnostic techniques and therapeutic measures undreamed of a few short decades ago are now commonplace. There is no reason why these developments should be any more dehumanizing than the use of similar techniques in modern transportation or communication, nor is their expense out of proportion when compared with other demands on the nation's purse. British workers have been at the forefront of many recent advances. Yet, even though the National Health Service provides a ready market for the products of British medical technology, the nation depends to an inordinate degree on imported products. In the development of appropriate medical technology there is an urgent need for better communication between inventors, scientists, industrialists and the National Health Service. At the same time there is an equal need for improved evaluation of untried techniques. The pressure for a central integrating body to coordinate resources could well be supported by the establishment of evaluation units in the different health authorities in this country.

  19. Emergent technologies: 25 years

    Science.gov (United States)

    Rising, Hawley K.

    2013-03-01

    This paper will talk about the technologies that have been emerging over the 25 years since the Human Vision and Electronic Imaging conference began that the conference has been a part of, and that have been a part of the conference, and will look at those technologies that are emerging today, such as social networks, haptic technologies, and still emerging imaging technologies, and what we might look at for the future.Twenty-five years is a long time, and it is not without difficulty that we remember what was emerging in the late 1980s. Yet to be developed: The first commercial digital still camera was not yet on the market, although there were hand held electronic cameras. Personal computers were not displaying standardized images, and image quality was not something that could be talked about in a standardized fashion, if only because image compression algorithms were not standardized yet for several years hence. Even further away were any standards for movie compression standards, there was no personal computer even on the horizon which could display them. What became an emergent technology and filled many sessions later, image comparison and search, was not possible, nor the current emerging technology of social networks- the world wide web was still several years away. Printer technology was still devising dithers and image size manipulations which would consume many years, as would scanning technology, and image quality for both was a major issue for dithers and Fourier noise.From these humble beginnings to the current moves that are changing computing and the meaning of both electronic devices and human interaction with them, we will see a course through the changing technology that holds some features constant for many years, while others come and go.

  20. Communication and collaboration technologies.

    Science.gov (United States)

    Cheeseman, Susan E

    2012-01-01

    This is the third in a series of columns exploring health information technology (HIT) in the neonatal intensive care unit (NICU). The first column provided background information on the implementation of information technology throughout the health care delivery system, as well as the requisite informatics competencies needed for nurses to fully engage in the digital era of health care. The second column focused on information and resources to master basic computer competencies described by the TIGER initiative (Technology Informatics Guiding Education Reform) as learning about computers, computer networks, and the transfer of data.1 This column will provide additional information related to basic computer competencies, focusing on communication and collaboration technologies. Computers and the Internet have transformed the way we communicate and collaborate. Electronic communication is the ability to exchange information through the use of computer equipment and software.2 Broadly defined, any technology that facilitates linking one or more individuals together is a collaborative tool. Collaboration using technology encompasses an extensive range of applications that enable groups of individuals to work together including e-mail, instant messaging (IM ), and several web applications collectively referred to as Web 2.0 technologies. The term Web 2.0 refers to web applications where users interact and collaborate with each other in a collective exchange of ideas generating content in a virtual community. Examples of Web 2.0 technologies include social networking sites, blogs, wikis, video sharing sites, and mashups. Many organizations are developing collaborative strategies and tools for employees to connect and interact using web-based social media technologies.3.

  1. Advances in Gyroscope Technologies

    CERN Document Server

    Armenise, Mario N; Dell'Olio, Francesco; Passaro, Vittorio MN

    2011-01-01

    This monograph collects and critically reviews the main results obtained by the scientific community in gyroscope technologies research field. It describes architectures, design techniques and fabrication technology of angular rate sensors proposed in literature. MEMS, MOEMS, optical and mechanical technologies are discussed together with achievable performance. The book also considers future research trends aimed to cover special applications. The book is intended for researchers and Ph.D. students interested in modelling, design and fabrication of gyros. The book may be a useful education su

  2. Interpretation of Internet technology

    DEFF Research Database (Denmark)

    Madsen, Charlotte Øland

    2001-01-01

    Research scope: The topic of the research project is to investigate how new internet technologies such as e-trade and customer relation marketing and management are implemented in Danish food processing companies. The aim is to use Weick's (1995) sensemaking concept to analyse the strategic....... Additionally, the project will investigate the technological strategies in organisations in order to gain a deeper understanding of the cognitive barriers towards implementing new technology in organisations. The research will therefore concentrate on the development process in the organisation's perception...

  3. Benchmarking semantic web technology

    CERN Document Server

    García-Castro, R

    2009-01-01

    This book addresses the problem of benchmarking Semantic Web Technologies; first, from a methodological point of view, proposing a general methodology to follow in benchmarking activities over Semantic Web Technologies and, second, from a practical point of view, presenting two international benchmarking activities that involved benchmarking the interoperability of Semantic Web technologies using RDF(S) as the interchange language in one activity and OWL in the other.The book presents in detail how the different resources needed for these interoperability benchmarking activities were defined:

  4. Biometrics Bodies, Technologies, Biopolitics

    CERN Document Server

    Pugliese, Joseph

    2012-01-01

    Biometric technologies, such as finger- or facial-scan, are being deployed across a variety of social contexts in order to facilitate and guarantee identity verification and authentication. In the post-9/11 world, biometric technologies have experienced an extraordinary period of growth as concerns about security and screening have increased. This book analyses biometric systems in terms of the application of biopolitical power - corporate, military and governmental - on the human body. It deploys cultural theory in examining the manner in which biometric technologies constitute the body as a

  5. Power generation technologies

    CERN Document Server

    Breeze, Paul

    2014-01-01

    The new edition of Power Generation Technologies is a concise and readable guide that provides an introduction to the full spectrum of currently available power generation options, from traditional fossil fuels and the better established alternatives such as wind and solar power, to emerging renewables such as biomass and geothermal energy. Technology solutions such as combined heat and power and distributed generation are also explored. However, this book is more than just an account of the technologies - for each method the author explores the economic and environmental costs and risk factor

  6. Educational technology, reimagined.

    Science.gov (United States)

    Eisenberg, Michael

    2010-01-01

    "Educational technology" is often equated in the popular imagination with "computers in the schools." But technology is much more than merely computers, and education is much more than mere schooling. The landscape of child-accessible technologies is blossoming in all sorts of directions: tools for communication, for physical construction and fabrication, and for human-computer interaction. These new systems and artifacts allow educational designers to think much more creatively about when and where learning takes place in children's lives, both within and outside the classroom.

  7. Communications technology handbook

    CERN Document Server

    Lewis, Geoff

    2013-01-01

    This is the first point of reference for the communications industries. It offers an introduction to a wide range of topics and concepts encountered in the field of communications technology. Whether you are looking for a simple explanation, or need to go into a subject in more depth, the Communications Technology Handbook provides all the information you need in one single volume.This second edition has been updated to include the latest technology including: Video on DemandWire-less Distribution systemsHigh spee

  8. Bridge technology report

    CERN Document Server

    2013-01-01

    Please note this is a Short Discount publication. As LANs have proliferated, new technologies and system concepts have come to the fore. One of the key issues is how to interconnect networks. One means of interconnection is to use a 'bridge'. Other competing technologies are repeaters, routers, and gateways. Bridges permit traffic isolation, connect network segments together and operate at the MAC layer. Further, because they operate at the MAC layer, they can handle a variety of protocols such as TCP/IP, SNA, and X.25. This report focuses on the specific technology of bridging two netw

  9. Strategic Health Technology Incorporation

    CERN Document Server

    Wang, Binseng

    2009-01-01

    Technology is essential to the delivery of health care but it is still only a tool that needs to be deployed wisely to ensure beneficial outcomes at reasonable costs. Among various categories of health technology, medical equipment has the unique distinction of requiring both high initial investments and costly maintenance during its entire useful life. This characteristic does not, however, imply that medical equipment is more costly than other categories, provided that it is managed properly. The foundation of a sound technology management process is the planning and acquisition of equipment

  10. Calculations in furnace technology

    CERN Document Server

    Davies, Clive; Hopkins, DW; Owen, WS

    2013-01-01

    Calculations in Furnace Technology presents the theoretical and practical aspects of furnace technology. This book provides information pertinent to the development, application, and efficiency of furnace technology. Organized into eight chapters, this book begins with an overview of the exothermic reactions that occur when carbon, hydrogen, and sulfur are burned to release the energy available in the fuel. This text then evaluates the efficiencies to measure the quantity of fuel used, of flue gases leaving the plant, of air entering, and the heat lost to the surroundings. Other chapters consi

  11. OHVT technology roadmap [2000

    Energy Technology Data Exchange (ETDEWEB)

    Bradley, R.A.

    2000-02-01

    The OHVT Technology Roadmap for 2000 presents the multiyear program plan of the U.S. DOE's Office of Heavy Vehicle Technologies (OHVT). It is an update of the 1997 plan, reflecting changes in regulations and ongoing discussions with DOE's heavy vehicle customers. The technical plan covers three classes of trucks: (1) class 7-8 (large, on-highway trucks); (2) class 3-6 (medium duty trucks); (3) class 1-2 (pickups, vans, and sport utility vehicles) as well as enabling and supporting technologies. The Roadmap documents program goals, schedules, and milestones.

  12. Digital security technology simplified.

    Science.gov (United States)

    Scaglione, Bernard J

    2007-01-01

    Digital security technology is making great strides in replacing analog and other traditional security systems including CCTV card access, personal identification and alarm monitoring applications. Like any new technology, the author says, it is important to understand its benefits and limitations before purchasing and installing, to ensure its proper operation and effectiveness. This article is a primer for security directors on how digital technology works. It provides an understanding of the key components which make up the foundation for digital security systems, focusing on three key aspects of the digital security world: the security network, IP cameras and IP recorders.

  13. Footprints of alien technology

    Science.gov (United States)

    Davies, P. C. W.

    2012-04-01

    If alien civilizations do, or did, exist, their technology will impact their environment. Some consideration has been given to the detection of large-scale astro-engineering, such as Dyson spheres. However, a very advanced technology might leave more subtle footprints requiring sophisticated scientific methods to uncover. We must not overlook the possibility that alien technology has impacted our immediate astronomical environment, even Earth itself, but probably a very long time ago. This raises the question of what traces, if anything, might remain today. I shall consider the possibilities of biological, geological and physical traces, and suggest ways that we might search for them.

  14. Humanitarian demining technology toolbox

    Science.gov (United States)

    Joynt, Vernon P.

    2003-09-01

    This is a keynote address surveying the field of Humanitarian Demining (HD) from the viewpoint of a participating company. The controlling bodies, funding structures and some of the important sources of R&D relevant to HD are identified. The various techniques and technologies in common use as also technologies freshly put into field use are mentioned. The way in which they all fit into the demining toolbox is explained. Finally a view of future technologies that are potentially able to change HD efficiency and safety is discussed.

  15. Responsible technology acceptance

    DEFF Research Database (Denmark)

    Toft, Madeleine Broman; Schuitema, Geertje; Thøgersen, John

    2014-01-01

    As a response to climate change and the desire to gain independence from imported fossil fuels, there is a pressure to increase the proportion of electricity from renewable sources which is one of the reasons why electricity grids are currently being turned into Smart Grids. In this paper, we focus...... in terms of a positive impact for society and the environment. Therefore, we expect that Smart Grid technology acceptance can be better explained when the well-known technology acceptance parameters included in the Technology Acceptance Model are supplemented by moral norms as suggested by the Norm...

  16. ACCELERATING NANO-TECHNOLOGICAL

    DEFF Research Database (Denmark)

    Jensen, Jens Stissing; Koch, Christian

    2007-01-01

    By viewing the construction industry as a technological innovation system (TIS) this paper discusses possible initiatives to accelerate nanotechnological innovations. The point of departure is a recent report on the application of nano-technology in the Danish construction industry, which concludes...... of the system are furthermore poorly equipped at identifying potentials within high-tech areas. In order to exploit the potentials of nano-technology it is thus argued that an alternative TIS needs to be established. Initiatives should identify and support “incubation rooms” or marked niches in order...

  17. Mobile Router Technology Development

    Science.gov (United States)

    Ivancic, William D.; Stewart, David H.; Bell, Terry L.; Kachmar, Brian A.; Shell, Dan; Leung, Kent

    2002-01-01

    Cisco Systems and NASA have been performing joint research on mobile routing technology under a NASA Space Act Agreement. Cisco developed mobile router technology and provided that technology to NASA for applications to aeronautic and space-based missions. NASA has performed stringent performance testing of the mobile router, including the interaction of routing and transport-level protocols. This paper describes mobile routing, the mobile router, and some key configuration parameters. In addition, the paper describes the mobile routing test network and test results documenting the performance of transport protocols in dynamic routing environments.

  18. Technology Transfer/Commercialization Report

    Science.gov (United States)

    2002-01-01

    Contents include the following: (1) Who we are. (2) Technology opportunities and successes in 2002: Hilbert-Huang transform; new sensors via sol-gel-filled fiber optics; hierarchical segmentation software. (3) Activities in 2002: encouraging researcher involvement; inventorying new technologies; patenting Goddard technologies; promoting Goddard technologies; establishing new agreements;seeking and bestowing awards. (4) How to reach Goddard's: technology commercialization office.

  19. Gauging Technology Costs and Benefits

    Science.gov (United States)

    Kaestner, Rich

    2007-01-01

    Regardless of the role technology plays in a school district, district personnel should know the costs associated with technology, understand the consequences of technology purchases, and be able to measure the benefits of technology, so they can make more informed decisions. However, determining costs and benefits of current technology or…

  20. Technology Transfer/Commercialization Report

    Science.gov (United States)

    2002-01-01

    Contents include the following: (1) Who we are. (2) Technology opportunities and successes in 2002: Hilbert-Huang transform; new sensors via sol-gel-filled fiber optics; hierarchical segmentation software. (3) Activities in 2002: encouraging researcher involvement; inventorying new technologies; patenting Goddard technologies; promoting Goddard technologies; establishing new agreements;seeking and bestowing awards. (4) How to reach Goddard's: technology commercialization office.

  1. GENERAL ENVIRONMENTAL CORPORATION; CURE ELECTROCOAGULATION TECHNOLOGY: INNOVATIVE TECHNOLOGY EVALUATION REPORT

    Science.gov (United States)

    The CURE electrocoagulation technology was demonstrated under the Superfund Innovative Technology Evaluation (SITE) program at the U.S. Department of Energy (DOE) Rocky Flats Environmental Technology Site (RFETS), where water from the solar evaporation ponds (SEPs) was contaminat...

  2. Technology development and technology gap among Latin American countries

    OpenAIRE

    Serrano Moya, Edgar David

    2014-01-01

    Objective: to study the source of the technology gaps amongst some Latin American countries and to identify whether a regional system of technological progress may be strengthened. ethodology: technology development within some Latin America countries was researched based on the technology frontier concept. In order to do that, the technological advancement of such countries was compared using standard variables and institutional systems. The concept and scope of the technology frontier, whic...

  3. Technology-Use Mediation

    DEFF Research Database (Denmark)

    Bansler, Jørgen P.; Havn, Erling C.

    2004-01-01

    Implementation of new computer-mediated communication (CMC) systems in organizations is a complex socio-technical endeavour, involving the mutual adaptation of technology and organization over time. Drawing on the analytic concept of sensemaking, this paper provides a theoretical perspective...... that deepens our understanding of how organizations appropriate new electronic communication media. The paper analyzes how a group of mediators in a large, multinational company adapted a new web-based CMC technology (a virtual workspace) to the local organizational context (and vice versa) by modifying...... features of the technology, providing ongoing support for users, and promoting appropriate conventions of use. We found that these mediators exerted considerable influence on how the technology was established and used in the organization. The mediators were not neutral facilitators of a well...

  4. Ocean Technology Development Tank

    Data.gov (United States)

    Federal Laboratory Consortium — The new SWFSC laboratory in La Jolla incorporates a large sea- and fresh-water Ocean Technology Development Tank. This world-class facility expands NOAA's ability to...

  5. Technologies, Transformations, and Responses

    Directory of Open Access Journals (Sweden)

    Sha Li Zhang

    2000-04-01

    Full Text Available

    頁次:18-23

    Technological innovations have played significant roles in improving human conditions in the history of civilization. The quality of life is expected to improve further as a result of the evolving technologies. Libraries have benefited by the many advantages offered through technology. Positive responses to new technological breakthroughs will enable libraries to provide improved and value-added services in our rapidly changing environment.

  6. Modern technologies in Endodontics

    Directory of Open Access Journals (Sweden)

    Alfredo Iandolo

    2016-06-01

    Conclusions: The positive results highlighted by these clinical cases demonstrate how the use of modern technologies are essential to avoid iatrogenic injury, and guarantee, on the other hand, safe and reproducible results.

  7. Modern technologies in Endodontics

    National Research Council Canada - National Science Library

    Iandolo, Alfredo; Iandolo, Giuseppe; Malvano, Mariano; Pantaleo, Giuseppe; Simeone, Michele

    2016-01-01

    .... Materials and methods: Today, thanks to modern technologies as Operative Microscope, ultrasonic tips, M-Wire Files, devices to activate irrigation and tridimensional obturation performed with thermo plasticized gutta...

  8. Applied machining technology

    CERN Document Server

    Tschätsch, Heinz

    2010-01-01

    Machining and cutting technologies are still crucial for many manufacturing processes. This reference presents all important machining processes in a comprehensive and coherent way. It includes many examples of concrete calculations, problems and solutions.

  9. Insider protection technology developments

    Energy Technology Data Exchange (ETDEWEB)

    Foesch, J.; Bortniak, P.; Waddoups, I.

    1994-08-01

    Sandia National Laboratories evaluates and develops new techniques and technologies to ensure the integrity of special nuclear material (SNM) against potential insider threats. We have evaluated several types of sensor technologies and subsystems to monitor and/or track materials and personnel. This past year`s effort has been directed at characterizing commercial developments that meet the Department of Energy`s (DOE) needs in some of these areas. Some of these evaluations are complete and some are still in progress. This paper discusses our work with infrared light (IR), radio frequency (RF), and RF proximity technologies. After these technologies are judged to be applicable to DOE`s needs, we incorporate them into the generic, real time, personnel tracking and material monitoring system.

  10. Power conversion technologies

    Energy Technology Data Exchange (ETDEWEB)

    Newton, M. A.

    1997-02-01

    The Power Conversion Technologies thrust area identifies and sponsors development activities that enhance the capabilities of engineering at Lawrence Livermore National Laboratory (LLNL) in the area of solid- state power electronics. Our primary objective is to be a resource to existing and emerging LLNL programs that require advanced solid-state power electronic technologies.. Our focus is on developing and integrating technologies that will significantly impact the capability, size, cost, and reliability of future power electronic systems. During FY-96, we concentrated our research efforts on the areas of (1) Micropower Impulse Radar (MIR); (2) novel solid-state opening switches; (3) advanced modulator technology for accelerators; (4) compact accelerators; and (5) compact pulse generators.

  11. Prosthetics and Related Technology

    Science.gov (United States)

    ... of prostheses, using leading- edge technologies such as robotics, tissue engineering, and nanotechnology to create lighter limbs ... and respiration. In a study of 32 chronic stroke patients, VA researchers found that functional neuromuscu- lar ...

  12. Armament Technology Facility (ATF)

    Data.gov (United States)

    Federal Laboratory Consortium — The Armament Technology Facility is a 52,000 square foot, secure and environmentally-safe, integrated small arms and cannon caliber design and evaluation facility....

  13. Extravehicular activity technology discipline

    Science.gov (United States)

    Webbon, Bruce W.

    1990-01-01

    Viewgraphs on extravehicular activity technology discipline for Space Station Freedom are presented. Topics covered include: extravehicular mobility unit; airlock and EMU support equipment; tools, mobility aids, and workstations; and telerobotic work aids interfaces.

  14. Fiber Optics Technology.

    Science.gov (United States)

    Burns, William E.

    1986-01-01

    Discusses various applications of fiber optics technology: information systems, industrial robots, medicine, television, transportation, and training. Types of jobs that will be available with fiber optics training (such as electricians and telephone cable installers and splicers) are examined. (CT)

  15. Utopian Approaches to Technology.

    Science.gov (United States)

    Lewis, Arthur O.

    1987-01-01

    Differentiates between utopian societies and their opposite, anti-utopias. Cites literary works which refer to the relationships between utopias and technology. Provides a bibliography of works cited as well as secondary sources. (TW)

  16. Sustainable advanced construction technologies

    CSIR Research Space (South Africa)

    Kuchena, JC

    2009-11-01

    Full Text Available Advanced Construction Technologies (ACTs) are set to become the sustainable mainstay of the construction industry due to the demand for innovative housing solutions. Like most emerging economies, South Africa from a historical perspective and global...

  17. Radiologic Technology Program Standards.

    Science.gov (United States)

    Georgia Univ., Athens. Dept. of Vocational Education.

    This publication contains statewide standards for the radiologic technology program in Georgia. The standards are divided into 12 categories; Foundations (philosophy, purpose, goals, program objectives, availability, evaluation); Admissions (admission requirements, provisional admission requirements, recruitment, evaluation and planning); Program…

  18. Handbook of vacuum technology

    CERN Document Server

    2016-01-01

    This comprehensive, standard work has been updated to remain an important resource for all those needing detailed knowledge of the theory and applications of vacuum technology. With many numerical examples and illustrations to visualize the theoretical issues.

  19. Manned systems technology discipline

    Science.gov (United States)

    Bretoi, Remus

    1990-01-01

    Viewgraphs on manned systems technology discipline for Space Station Freedom are presented. Topics covered include: crew-systems interfaces and interactions; crew training; on-board systems maintenance and support; habitability and environment; and computational human factors.

  20. CSIR Technology Impact 2003

    CSIR Research Space (South Africa)

    CSIR

    2003-01-01

    Full Text Available This issue of Technology Impact offers a brief snapshot of CSIR activities during the year under review (1 March 2002 - 28 February 2003) by highlighting a number of innovative projects and initiatives in various CSIR business units....

  1. Technology in cardiology

    African Journals Online (AJOL)

    Repro

    noticeable link with advanced medical technology for ... function by echocardiography allows opti- ... blood vessels smaller than 1 mm in diameter, but also the accurate placement of devices such as stents. ... of a darkened room for the light.

  2. Information and Communication Technology

    DEFF Research Database (Denmark)

    Kaila, Heidi Kristiina

    2017-01-01

    The emergence and development of the information and communication sector has been rapid in rural Viet Nam over 2006–14, and a true information and communication technology (ICT) revolution has taken place. This chapter examines household ownership and use of ICT. It studies the geographic...... and demographic differences across ownership of technology, especially phones and the Internet, and the determinants of ICT adoption. First, it finds that expansion of telephones has been much more rapid than the expansion of the Internet. Second, it finds that even though in 2014 internet users were relatively...... wealthier and more educated than households with phones on average, the adoption patterns of these two technologies are very similar. ICT adoption is driven by education and income, as well as wealth and ownership of other technology....

  3. Will Technology Humanize Us?

    Science.gov (United States)

    Snider, Robert C.

    1972-01-01

    The author considers the question of whether technology will cause humanization or dehumanization in the schools. He concludes that we can not stop tecchnology; we can only give it direction and purpose. (Author/MS)

  4. Transforming Lessons with Technology

    Science.gov (United States)

    Currie, Brad

    2016-01-01

    Using a fictitious learning environment, the author demonstrates a variety of technological tools that teachers can infuse into their classrooms. Come away with some innovative, practical methods to help students show what they know about the topic at hand.

  5. Technology Enhanced Learning

    NARCIS (Netherlands)

    Klemke, Roland; Specht, Marcus

    2013-01-01

    Klemke, R., & Specht, M. (2013, 26-27 September). Technology Enhanced Learning. Presentation at the fourth international conference on eLearning (eLearning 2013), Belgrade, Serbia. http://econference.metropolitan.ac.rs/

  6. Technologies for Legionella Control

    Science.gov (United States)

    Presentation includes a review of new Office of Water document entitled "Technologies for Legionella Control in Premise Plumbing Systems", and discussion on ORD research projects involving Legionella and disinfection.

  7. Technology catalogue. Second edition

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-04-01

    The Department of Energy`s (DOE`s) Office of Environmental Management (EM) is responsible for remediating DOE contaminated sites and managing the DOE waste inventory in a safe and efficient manner. EM`s Office of Technology Development (OTD) supports applied research and demonstration efforts to develop and transfer innovative, cost-effective technologies to its site clean-up and waste-management programs within EM. The purpose of the Technology Catalogue is to: (a) provide performance data on OTD-developed technologies to scientists and engineers responsible for preparing Remedial Investigation/Feasibility Studies (RI/FSs) and other compliance documents for the DOE`s clean-up and waste-management programs; and (b) identify partnering and commercialization opportunities with industry, other federal and state agencies, and the academic community.

  8. Digital Technology Entrepreneurship

    DEFF Research Database (Denmark)

    Giones, Ferran; Brem, Alexander

    2017-01-01

    Technology entrepreneurship is an established concept in academia. However, recent developments in the context of digital entrepreneurship call for revision and advance- ment. The multiple possible combinations of technology and entrepreneurship have res- ulted in a diversity of phenomena...... with significantly different characteristics and socio-economic impact. This article is focused on the identification and description of technology entrepreneurship in times of digitization. Based on current examples, we identify and describe characterizations of technology entrepreneurship, digital techno- logy...... entrepreneurship, and digital entrepreneurship. With this new delineation of terms, we would like to foster discussion between researchers, entrepreneurs, and policy makers on the impact of digitization on entrepreneurship, and set a future research agenda....

  9. Research and Technology 1980

    Science.gov (United States)

    1980-01-01

    Topics are divided into three major areas: Earth resources, advanced development, and technology transfer. Topics include: aerial color infrared photography, fiber optics, lightning research, soil mechanics, corrosion prevention, image processing, and communication systems development.

  10. CSIR Technology Impact 2002

    CSIR Research Space (South Africa)

    CSIR

    2002-01-01

    Full Text Available This issue of Technology Impact offers a brief snapshot of CSIR activities during the year under review (1 March 2001 - 28 February 2002) by highlighting a number of innovative projects and initiatives in these areas....

  11. Launching technological innovations

    DEFF Research Database (Denmark)

    Talke, Katrin; Salomo, Søren

    2009-01-01

    have received less attention. This study considers the interdependencies between strategic, internally and externally, directed tactical launch activities and investigates both direct and indirect performance effects. The analysis is based upon data from 113 technological innovations launched...

  12. Accelerator Technology Division

    Science.gov (United States)

    1992-04-01

    In fiscal year (FY) 1991, the Accelerator Technology (AT) division continued fulfilling its mission to pursue accelerator science and technology and to develop new accelerator concepts for application to research, defense, energy, industry, and other areas of national interest. This report discusses the following programs: The Ground Test Accelerator Program; APLE Free-Electron Laser Program; Accelerator Transmutation of Waste; JAERI, OMEGA Project, and Intense Neutron Source for Materials Testing; Advanced Free-Electron Laser Initiative; Superconducting Super Collider; The High-Power Microwave Program; (Phi) Factory Collaboration; Neutral Particle Beam Power System Highlights; Accelerator Physics and Special Projects; Magnetic Optics and Beam Diagnostics; Accelerator Design and Engineering; Radio-Frequency Technology; Free-Electron Laser Technology; Accelerator Controls and Automation; Very High-Power Microwave Sources and Effects; and GTA Installation, Commissioning, and Operations.

  13. Lessons of Educational Technology

    Directory of Open Access Journals (Sweden)

    Manuela Repetto

    2006-01-01

    Full Text Available Reception of the book "Lessons of Educational Technology." The book contains materials work in certain aspects relevant to the formation of a teacher who is able to meet the challenges of society 'knowledge.

  14. Advances in production technology

    CERN Document Server

    2015-01-01

    This edited volume contains the selected papers presented at the scientific board meeting of the German Cluster of Excellence on “Integrative Production Technology for High-Wage Countries”,  held in November 2014. The topical structure of the book is clustered in six sessions: Integrative Production Technology, Individualised Production, Virtual Production Systems, Integrated Technologies, Self-Optimising Production Systems and Human Factors in Production Technology. The Aachen perspective on a holistic theory of production is complemented by conference papers from external leading researchers in the fields of production, materials science and bordering disciplines. The target audience primarily comprises research experts and practitioners in the field but the book may also be beneficial for graduate students.

  15. Wavelength converter technology

    DEFF Research Database (Denmark)

    Kloch, Allan; Hansen, Peter Bukhave; Poulsen, Henrik Nørskov;

    1999-01-01

    Wavelength conversion is important since it ensures full flexibility of the WDM network layer. Progress in optical wavelength converter technology is reviewed with emphasis on all-optical wavelength converter types based on semiconductor optical amplifiers....

  16. Wavelength converter technology

    DEFF Research Database (Denmark)

    Kloch, Allan; Hansen, Peter Bukhave; Poulsen, Henrik Nørskov;

    1999-01-01

    Wavelength conversion is important since it ensures full flexibility of the WDM network layer. Progress in optical wavelength converter technology is reviewed with emphasis on air-optical wavelength converter types based on semiconductor optical amplifiers....

  17. Handbook of antenna technologies

    CERN Document Server

    Liu, Duixian; Nakano, Hisamatsu; Qing, Xianming; Zwick, Thomas

    2016-01-01

    The Handbook of Antenna Technologies aims to present the rapid development of antenna technologies, particularly in the past two decades, and also showcasing the newly developed technologies and the latest applications. The handbook will provide readers with the comprehensive updated reference information covering theory, modeling and optimization methods, design and measurement, new electromagnetic materials, and applications of antennas. The handbook will widely cover not only all key antenna design issues but also fundamentals, issues related to antennas (transmission, propagation, feeding structure, materials, fabrication, measurement, system, and unique design challenges in specific applications). This handbook will benefit the readers as a full and quick technical reference with a high-level historic review of technology, detailed technical descriptions and the latest practical applications.

  18. Melter Technologies Assessment

    Energy Technology Data Exchange (ETDEWEB)

    Perez, J.M. Jr. [Pacific Northwest National Lab., Richland, WA (United States); Schumacher, R.F. [Savannah River Technology Center, Aiken, SC (United States); Forsberg, C.W. [Oak Ridge National Lab., TN (United States)

    1996-05-01

    The problem of controlling and disposing of surplus fissile material, in particular plutonium, is being addressed by the US Department of Energy (DOE). Immobilization of plutonium by vitrification has been identified as a promising solution. The Melter Evaluation Activity of DOE`s Plutonium Immobilization Task is responsible for evaluating and selecting the preferred melter technologies for vitrification for each of three immobilization options: Greenfield Facility, Adjunct Melter Facility, and Can-In-Canister. A significant number of melter technologies are available for evaluation as a result of vitrification research and development throughout the international communities for over 20 years. This paper describes an evaluation process which will establish the specific requirements of performance against which candidate melter technologies can be carefully evaluated. Melter technologies that have been identified are also described.

  19. Mississippi Technology Transfer Center

    Science.gov (United States)

    1987-01-01

    The Mississippi Technology Transfer Center at the John C. Stennis Space Center in Hancock County, Miss., was officially dedicated in 1987. The center is home to several state agencies as well as the Center For Higher Learning.

  20. Tablet Technologies and Education

    OpenAIRE

    Heidi L. Schnackenberg

    2013-01-01

    Recently, tablet technologies have grown tremendously in popularity. They lend themselves to a myriad of learning modalities and therefore may be well suited to use in schools and universities. While teachers work to find useful applications for tablets, students have already begun using them at home and, in secondary and higher education, in classes. Unfortunately, sometimes when students use tablets for courses they play with “apps,” rather than using the technology as a useful and powerful...

  1. Technology which desires

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Sangyook

    2009-03-15

    The table of contents are technology, human and society, Frankenstein, prometheus in modern, modern technology which are pressing human and nature, utopia and dystopia don't come, progressing of bicycle, Edison built the system, clock and human from nano paint to nano machine, diesel locomotive and KTX, airplanes is disappearing, machine is monsters, Taylorism and dream of engineer, union between mass production and public consumption, go away mass production, humanoid and a cyborg and beginning of global village.

  2. Grating image technology

    Science.gov (United States)

    Iwata, Fujio

    1995-07-01

    The word 'grating image' was first named by Toppan Printing Company, Ltd. It means that an image consists of grating dots. In 1988, we presented this new technology at the Optical Security Systems Symposium, in Switzerland. Then it was improved and applied in display application. Recently, it was further applied in 3D video systems. In this report, the development history and the recent situations of grating image technology are described.

  3. Industrial communication technology handbook

    CERN Document Server

    Zurawski, Richard

    2014-01-01

    Featuring contributions from major technology vendors, industry consortia, and government and private research establishments, the Industrial Communication Technology Handbook, Second Edition provides comprehensive and authoritative coverage of wire- and wireless-based specialized communication networks used in plant and factory automation, automotive applications, avionics, building automation, energy and power systems, train applications, and more.New to the Second Edition:46 brand-new chapters and 21 substantially revised chaptersInclusion of the latest, most significant developments in spe

  4. Advanced GPS Technologies (AGT)

    Science.gov (United States)

    2015-05-01

    V Air Force Research Laboratory ••• Advanced GPS Technologies (AGT) Integrity *Service *Excellence 1 May 2015 Kevin Slimak Program Manager...2015 2. REPORT TYPE 3. DATES COVERED 00-00-2015 to 00-00-2015 4. TITLE AND SUBTITLE Advanced GPS Technologies (AGT) 5a. CONTRACT NUMBER 5b...DISTRIBUTION/AVAILABILITY STATEMENT Approved for public release; distribution unlimited 13. SUPPLEMENTARY NOTES Presented at the GPS Partnership

  5. Industry Service - Technology Centre

    DEFF Research Database (Denmark)

    Hollensen, Svend; Grünbaum, Niels Nolsøe

    2011-01-01

    The chapter describes and explains the development of an Industry Service Technology (IS-T) portal solution at Danfoss for testing of products, including booking system for standardised 'service packages' in order to reduce waiting time.......The chapter describes and explains the development of an Industry Service Technology (IS-T) portal solution at Danfoss for testing of products, including booking system for standardised 'service packages' in order to reduce waiting time....

  6. Technology development for safeguards

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Ho Dong; Kang, H. Y.; Song, D. Y. [and others

    2005-04-01

    The objective of this project are to establish the safeguards technology of the nuclear proliferation resistance to the facilities which handle with high radioactivity nuclear materials like the spent fuel, to provide the foundation of the technical independency for the establishment of the effective management of domestic spent fuels, and to construct the base of the early introduction of the key technology relating to the back-end nuclear fuel cycle through the development of the safeguards technology of the DFDF of the nuclear non-proliferation. The essential safeguards technologies of the facility such as the measurement and account of nuclear materials and the C/S technology were carried out in this stage (2002-2004). The principal results of this research are the development of error reduction technology of the NDA equipment and a new NDA system for the holdup measurement of process materials, the development of the intelligent surveillance system based on the COM, the evaluation of the safeguardability of the Pyroprocessing facility which is the core process of the nuclear fuel cycle, the derivation of the research and development items which are necessary to satisfy the safeguards criteria of IAEA, and the presentation of the direction of the technology development relating to the future safeguards of Korea. This project is the representative research project in the field of the Korea's safeguards. The safeguards technology and equipment developed while accomplishing this project can be applied to other nuclear fuel cycle facilities as well as DFDF and will be contributed to increase the international confidence in the development of the nuclear fuel cycle facility of Korea and its nuclear transparency.

  7. Department of Reactor Technology

    DEFF Research Database (Denmark)

    Risø National Laboratory, Roskilde

    The general development of the Department of Reactor Technology at Risø during 1981 is presented, and the activities within the major subject fields are described in some detail. Lists of staff, publications, and computer programs are included.......The general development of the Department of Reactor Technology at Risø during 1981 is presented, and the activities within the major subject fields are described in some detail. Lists of staff, publications, and computer programs are included....

  8. Technology makes life better

    Institute of Scientific and Technical Information of China (English)

    李红

    2015-01-01

    There are many theories about the relationship between technology and society.With the development of world economy,technology has made great progress.However,many changes were taken place in our daily life,especially the appearance of computer.Sending emails,chatting with others online,search for information which is what we need to learn and many other demands in people’s daily life,computers make all of it into possibility.

  9. Technology of Quantum Devices

    CERN Document Server

    Razeghi, Manijeh

    2010-01-01

    Technology of Quantum Devices offers a multi-disciplinary overview of solid state physics, photonics and semiconductor growth and fabrication. Readers will find up-to-date coverage of compound semiconductors, crystal growth techniques, silicon and compound semiconductor device technology, in addition to intersubband and semiconductor lasers. Recent findings in quantum tunneling transport, quantum well intersubband photodetectors (QWIP) and quantum dot photodetectors (QWDIP) are described, along with a thorough set of sample problems.

  10. Maturity in technology

    Directory of Open Access Journals (Sweden)

    L. Alberts

    1988-03-01

    Full Text Available The concept is developed that modern technology, because of its relationship with pure science, can never really become mature, but will always grow as the pool of scientific knowledge grows. Parameters indicating to some extent the degree of technological prowess in a society are compared for a spectrum of countries. It is clear that in spite of some internationally outstanding successes. South Africa must be regarded on average as a developing society.

  11. Hybrid microelectronic technology

    Science.gov (United States)

    Moran, P.

    Various areas of hybrid microelectronic technology are discussed. The topics addressed include: basic thick film processing, thick film pastes and substrates, add-on components and attachment methods, thin film processing, and design of thick film hybrid circuits. Also considered are: packaging hybrid circuits, automating the production of hybrid circuits, application of hybrid techniques, customer's view of hybrid technology, and quality control and assurance in hybrid circuit production.

  12. Information technology made simple

    CERN Document Server

    Carter, Roger

    1991-01-01

    Information Technology: Made Simple covers the full range of information technology topics, including more traditional subjects such as programming languages, data processing, and systems analysis. The book discusses information revolution, including topics about microchips, information processing operations, analog and digital systems, information processing system, and systems analysis. The text also describes computers, computer hardware, microprocessors, and microcomputers. The peripheral devices connected to the central processing unit; the main types of system software; application soft

  13. Advocacy and technology assessment

    Science.gov (United States)

    Jones, E. M.

    1975-01-01

    A highly structured treatment is presented of adversarial systems as they apply to technology assessment. One approach to the problem of adequate criteria of assessment focuses upon the internal operations of assessment entities; operations include problem perception, problem formulation, selection, utilization, determination, and evaluation. Potential contributions of advocacy as a mode of inquiry in technology are discussed; advocacy is evaluated by representative sets of criteria of adequate assessment which include participant criteria, perspectives criteria, situations criteria, base values criteria, and strategies criteria.

  14. Polymer optical motherboard technology

    Science.gov (United States)

    Keil, N.; Yao, H.; Zawadzki, C.; Grote, N.; Schell, M.

    2008-02-01

    In this paper, different hybridly integrated optical devices including optical multiplexer/ demultiplexer and optical transceivers are described. The devices were made using polymer planar light wave circuit (P2LC) technology. Laser diodes, photodiodes, and thin-film filters have been integrated. Key issues involved in this technology, in particular the coupling between laser diodes and polymer waveguides, and between waveguides and photodiodes and also fibers are discussed.

  15. Survey of Web Technologies

    OpenAIRE

    Špoljar, Boris

    2011-01-01

    The World Wide Web bas become an important platform for developing and running applications. A vital process while developing web applications is the choice of web technologies, on which the application will be build. The developers face a dizzying array of platforms, languages, frameworks and technical artifacts to choose from. The decison carries consequences on most other decisions in the development process. Thesis contains analisis, classifications and comparison of web technologies s...

  16. Market Leadership Through Technology

    DEFF Research Database (Denmark)

    Claussen, Jörg; Kretschmer, Tobias; Spengler, Thomas

    .S. market for handheld game consoles, we show that backward compatibility lets incumbents transfer network effects from the old generation to the new to some extent but that it also reduces supply of new software. We examine the tradeoff between technological progress and backward compatibility and find...... that backward compatibility matters less if there is a large technological leap between two generations. We subsequently use our results to assess the role of backward compatibility as a strategy to sustain market leadership....

  17. Broadcast sound technology

    CERN Document Server

    Talbot-Smith, Michael

    1990-01-01

    Broadcast Sound Technology provides an explanation of the underlying principles of modern audio technology. Organized into 21 chapters, the book first describes the basic sound; behavior of sound waves; aspects of hearing, harming, and charming the ear; room acoustics; reverberation; microphones; phantom power; loudspeakers; basic stereo; and monitoring of audio signal. Subsequent chapters explore the processing of audio signal, sockets, sound desks, and digital audio. Analogue and digital tape recording and reproduction, as well as noise reduction, are also explained.

  18. Technology Commercialization Program 1991

    Energy Technology Data Exchange (ETDEWEB)

    1991-11-01

    This reference compilation describes the Technology Commercialization Program of the Department of Energy, Defense Programs. The compilation consists of two sections. Section 1, Plans and Procedures, describes the plans and procedures of the Defense Programs Technology Commercialization Program. The second section, Legislation and Policy, identifies legislation and policy related to the Program. The procedures for implementing statutory and regulatory requirements are evolving with time. This document will be periodically updated to reflect changes and new material.

  19. Recombinant Technology and Probiotics

    OpenAIRE

    Icy D’Silva

    2011-01-01

    Recombinant technology has led the way to monumental advances in the development of useful molecules, including the development of safe probiotics. The development of novel approaches using recombinant technology and probiotics that allow accurate targeting of therapeutics to the mucosa is an interesting area of research. The creation and use of recombinant probiotics expressing recombinantovalbumin, recombinant ovalbumin mutants and yet-to-be-designed recombinant hypo/non-allergenic molecule...

  20. Technology Logic Diagrams

    Energy Technology Data Exchange (ETDEWEB)

    Rudin, M.J. [Univ. of Nevada, Las Vegas NV (United States); O`Brien, M.C. [Univ. of Arizona, Tucson, AZ (United States)

    1995-04-01

    A planning and management tool was developed that relates environmental restoration and waste management problems to technologies that can be used to remediate these problems. Although the Technology Logic Diagram has been widely used within the US Department of Energy`s Office of Environmental Restoration and Waste Management, it can be modified for use during the planning of any waste management and environmental cleanup effort.

  1. Token ring technology report

    CERN Document Server

    2013-01-01

    Please note this is a Short Discount publication. This report provides an overview of the IBM Token-Ring technology and products built by IBM and compatible vendors. It consists of two sections: 1. A summary of the design trade-offs for the IBM Token-Ring. 2. A summary of the products of the major token-ring compatible vendors broken down by adapters and components, wiring systems, testing, and new chip technology.

  2. Endogenous Technological Change

    OpenAIRE

    Paul Romer

    1989-01-01

    Growth in this model is driven by technological change that arises from intentional investment decisions made by profit maximizing agents. The distinguishing feature of the technology as an input is that it is neither a conventional good nor a public good; it is a nonrival, partially excludable good. Because of the nonconvexity introduced by a nonrival good, price-taking competition cannot be supported, and instead, the equilibriumis one with monopolistic competition. The main conclusions are...

  3. Technology of the Guitar

    CERN Document Server

    French, Richard Mark

    2012-01-01

    Featuring chapters on physics, structure, sound and design specifics, Technology of the Guitar also includes coverage of  historical content, composition of strings and their effects on sound quality, and important designs. Additionally, author Mark French discusses case studies of historically significant and technologically innovative instruments. This is a complete reference useful for a broad range of readers including guitar manufacturer employees, working luthiers, and interested guitar enthusiasts who do not have a science or engineering background.

  4. Virtual Campus Hub technology

    DEFF Research Database (Denmark)

    Vercoulen, Frank; Badger, Merete; Monaco, Lucio;

    This deliverable briefly describes which technological components have been delivered for the Virtual Campus Hub and how they can be used. A detailed discussion of the technical details of the components, how they were realized and how they fit the VCH concept can be found in deliverables D5.......4. Virtual Campus Hub Technology Evaluation Report and D6.7 The Virtual Campus Hub Concept....

  5. Energy Technology Innovation

    DEFF Research Database (Denmark)

    Brix, Jacob

    2015-01-01

    Anmeldelse af bogen: Energy Technology Innovation – Learning from Historical Successes and Failures, A. Grubler, C. Wilson (eds.) Cambridge University Press, New York (2014) 387p., ISBN: 978-1-107-02322-2......Anmeldelse af bogen: Energy Technology Innovation – Learning from Historical Successes and Failures, A. Grubler, C. Wilson (eds.) Cambridge University Press, New York (2014) 387p., ISBN: 978-1-107-02322-2...

  6. MOBILE AGENT: EMERGING TECHNOLOGY

    OpenAIRE

    RAJGURU P. V. DR. DESHMUKH S. D

    2011-01-01

    Mobile agent technology has been promoted as an emerging technology that makes it much easier to design, implement, and maintain distributed systems, introduction to basic concepts of mobile agents like agent mobility, agent types and places and agent communication. Then benefits of the usage of mobile agents are summarized and illustrated by selected applications. The next section lists requirements and desirable properties for mobile agent languages and systems. We study the main features, ...

  7. Geolocation Technologies Final Report

    Energy Technology Data Exchange (ETDEWEB)

    Magnoli, D E

    2003-06-02

    This paper is the final report for LL998 In Situ Sensing Subtask 7 (Geo-location) undertaken for NNSA NA-22 enabling technologies R&D for Counterproliferation Detection. A few state-of-the-art resolution parameters are presented for accelerometers, indoor and outdoor GPS (Global Positioning Satellite) systems, and INSs (Inertial Navigation Systems). New technologies are described, including one which has demonstrated the ability to track within a building to a resolution of under a foot.

  8. Market Leadership Through Technology

    DEFF Research Database (Denmark)

    Claussen, Jörg; Kretschmer, Tobias; Spengler, Thomas

    .S. market for handheld game consoles, we show that backward compatibility lets incumbents transfer network effects from the old generation to the new to some extent but that it also reduces supply of new software. We examine the tradeoff between technological progress and backward compatibility and find...... that backward compatibility matters less if there is a large technological leap between two generations. We subsequently use our results to assess the role of backward compatibility as a strategy to sustain market leadership....

  9. Nuclear Reactors and Technology

    Energy Technology Data Exchange (ETDEWEB)

    Cason, D.L.; Hicks, S.C. [eds.

    1992-01-01

    This publication Nuclear Reactors and Technology (NRT) announces on a monthly basis the current worldwide information available from the open literature on nuclear reactors and technology, including all aspects of power reactors, components and accessories, fuel elements, control systems, and materials. This publication contains the abstracts of DOE reports, journal articles, conference papers, patents, theses, and monographs added to the Energy Science and Technology Database during the past month. Also included are US information obtained through acquisition programs or interagency agreements and international information obtained through the International Energy Agency`s Energy Technology Data Exchange or government-to-government agreements. The digests in NRT and other citations to information on nuclear reactors back to 1948 are available for online searching and retrieval on the Energy Science and Technology Database and Nuclear Science Abstracts (NSA) database. Current information, added daily to the Energy Science and Technology Database, is available to DOE and its contractors through the DOE Integrated Technical Information System. Customized profiles can be developed to provide current information to meet each user`s needs.

  10. German energy technology prospects.

    Science.gov (United States)

    Popp, M

    1982-12-24

    After more than 25 years of development of nuclear power and almost 10 years of research and development in numerous areas of nonnuclear energy, there is now a good basis for judging the future prospects of energy technologies in the Federal Republic of Germany. The development of nuclear power has provided an important and economically advantageous new source of energy. Further efforts are needed to establish the nuclear fuel cycle in all stages and to exploit the potential of advanced reactors. In all other areas of energy technology, including energy conservation, new energy sources, and coal, economics has turned out to be the key problem, even at today's energy prices. Opportunities to overcome these economic problems through additional R & D are limited. There is some potential for special applications, and there are many technologies that could contribute to the energy supply of developing countries. In general, however, progress in energy conservation and the use of renewable energy sources will depend on the degree to which energy policy measures can improve their economic basis. For some technologies, such as solar thermal power stations and coal liquefaction, large-scale economic deployment cannot be foreseen today. Instead of establishing costly demonstration projects, emphasis will be put on improving key components of these technologies with the aim of having the most advanced technology available when the economic parameters are more favorable.

  11. Information technology resources assessment

    Energy Technology Data Exchange (ETDEWEB)

    Stevens, D.F. [ed.

    1992-01-01

    This year`s Information Technology Resources Assessment (ITRA) is something of a departure from traditional practice. Past assessments have concentrated on developments in fundamental technology, particularly with respect to hardware. They form an impressive chronicle of decreasing cycle times, increasing densities, decreasing costs (or, equivalently, increasing capacity and capability per dollar spent), and new system architectures, with a leavening of operating systems and languages. Past assessments have aimed -- and succeeded -- at putting information technology squarely in the spotlight; by contrast, in the first part of this assessment, we would like to move it to the background, and encourage the reader to reflect less on the continuing technological miracles of miniaturization in space and time and more on the second- and third-order implications of some possible workplace applications of these miracles. This Information Technology Resources Assessment is intended to provide a sense of technological direction for planners in projecting the hardware, software, and human resources necessary to support the diverse IT requirements of the various components of the DOE community. It is also intended to provide a sense of our new understanding of the place of IT in our organizations.

  12. Information technology resources assessment

    Energy Technology Data Exchange (ETDEWEB)

    Stevens, D.F. (ed.)

    1992-01-01

    This year's Information Technology Resources Assessment (ITRA) is something of a departure from traditional practice. Past assessments have concentrated on developments in fundamental technology, particularly with respect to hardware. They form an impressive chronicle of decreasing cycle times, increasing densities, decreasing costs (or, equivalently, increasing capacity and capability per dollar spent), and new system architectures, with a leavening of operating systems and languages. Past assessments have aimed -- and succeeded -- at putting information technology squarely in the spotlight; by contrast, in the first part of this assessment, we would like to move it to the background, and encourage the reader to reflect less on the continuing technological miracles of miniaturization in space and time and more on the second- and third-order implications of some possible workplace applications of these miracles. This Information Technology Resources Assessment is intended to provide a sense of technological direction for planners in projecting the hardware, software, and human resources necessary to support the diverse IT requirements of the various components of the DOE community. It is also intended to provide a sense of our new understanding of the place of IT in our organizations.

  13. Versions Of Care Technology

    Directory of Open Access Journals (Sweden)

    Sampsa Hyysalo

    2007-01-01

    Full Text Available The importance of users for innovation has been increasingly emphasized in the literatures on design and management of technology. However, less attention has been given to how people shape technology-in-use. This paper first provides a review of literature on technology use in the social and cultural studies of technology. It then moves to examine empirically how a novel alarm and monitoring appliance was appropriated in the work of home-care nurses and in the everyday living of elderly people. Analysis shows that even these technically unsavvy users shaped the technology considerably by various, even if mundane, acts of adapting it materially, as well as by attributing different meanings to it. However, the paper goes on to argue that such commonplace phrasing of the findings obscures their significance and interrelations. Consequently, the final section of the paper reframes the key findings of this study using the concepts of practice, enactment, and versions of technology to reach a more adequate description.

  14. Turbine imaging technology assessment

    Energy Technology Data Exchange (ETDEWEB)

    Moursund, R. A. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Carlson, T. J. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

    2004-12-01

    The goal of this project was to identify and evaluate imaging technologies for observing juvenile fish within a Kaplan turbine, and specifically that would enable scientists to determine mechanisms of fish injury within an operating turbine unit. This report documents the opportunities and constraints for observing juvenile fish at specific locations during turbine passage. These observations were used to make modifications to dam structures and operations to improve conditions for fish passage while maintaining or improving hydropower production. The physical and hydraulic environment that fish experience as they pass through the hydroelectric plants were studied and the regions with the greatest potential for injury were defined. Biological response data were also studied to determine the probable types of injuries sustained in the turbine intake and what types of injuries are detectable with imaging technologies. The study grouped injury-causing mechanisms into two categories: fluid (pressure/cavitation, shear, turbulence) and mechanical (strike/collision, grinding/pinching, scraping). The physical constraints of the environment, together with the likely types of injuries to fish, provided the parameters needed for a rigorous imaging technology evaluation. Types of technology evaluated included both tracking and imaging systems using acoustic technologies (such as sonar and acoustic tags) and optic technologies (such as pulsed-laser videography, which is high-speed videography using a laser as the flash). Criteria for determining image data quality such as frame rate, target detectability, and resolution were used to quantify the minimum requirements of an imaging sensor.

  15. Darwinism determines technological survivors

    Energy Technology Data Exchange (ETDEWEB)

    Bevc, F.; Harkness, S.

    1996-10-01

    In an industry where new power plant planning and budgeting cycles stretch from one to three years, where a typical new generation product takes from five to 10 years to successfully enter the market and where some plants have a 30- to 50-year economic life, change is an evolutionary process. However, that change, driven by the application of new technologies, is inevitable. Twenty-five years ago, in 1971, gas turbines were perceived to have limited applications and were primarily used for part-time peaking duty. Today, they are the baseload, new power generation technology of choice. Nevertheless, more than 55% of the US`s electricity is still generated by coal-fired steam turbine plants, the technology of choice 25 years ago. Power generation technologies will evolve further, but it`s doubtful there will be any new concepts that are not evident in today`s laboratories. Twenty-five years from now, today`s coal-fires team turbine plants will still provide the majority of the electricity generated in the US. However, new natural gas or syngas-fired combined-cycle plants will make up the majority of the new additions, perhaps as much as 20% of the overall installed capacity in 2021. Still, during the next 25 years, a number of new generation technologies should become economically competitive and enter the market. Technologies moving from today`s demonstrations to widespread applications include: gasification, pressurized fluidized bed combustion, fuel cell hybrid cycles, and solar photovoltaics.

  16. Information technology resources assessment

    Energy Technology Data Exchange (ETDEWEB)

    Loken, S.C. [ed.

    1993-01-01

    The emphasis in Information Technology (IT) development has shifted from technology management to information management, and the tools of information management are increasingly at the disposal of end-users, people who deal with information. Moreover, the interactive capabilities of technologies such as hypertext, scientific visualization, virtual reality, video conferencing, and even database management systems have placed in the hands of users a significant amount of discretion over how these resources will be used. The emergence of high-performance networks, as well as network operating systems, improved interoperability, and platform independence of applications will eliminate technical barriers to the use of data, increase the power and range of resources that can be used cooperatively, and open up a wealth of possibilities for new applications. The very scope of these prospects for the immediate future is a problem for the IT planner or administrator. Technology procurement and implementation, integration of new technologies into the existing infrastructure, cost recovery and usage of networks and networked resources, training issues, and security concerns such as data protection and access to experiments are just some of the issues that need to be considered in the emerging IT environment. As managers we must use technology to improve competitiveness. When procuring new systems, we must take advantage of scalable resources. New resources such as distributed file systems can improve access to and efficiency of existing operating systems. In addition, we must assess opportunities to improve information worker productivity and information management through tedmologies such as distributed computational visualization and teleseminar applications.

  17. 不同升温阈值下中国地区极端气候事件变化预估%Changes in Climate Extremes over China in a 2°C, 3°C, and 4°C Warmer World

    Institute of Scientific and Technical Information of China (English)

    陈晓晨; 徐影; 姚遥

    2015-01-01

    Due to human-induced global warming, global Average Surface Air Temperature (ASAT) will reach certain thresholds with reference to the pre-industrial period. Quantitative assessments of climate extremes across China when reaching these thresholds are important indicators in disaster risk management and policymaking. In this study, based on outputs of 18 General Circulation Models (GCMs) from the Coupled Model Intercomparison Project Phase 5 (CMIP5), 27 climate-extreme indices computed with a consistent methodology are used to quantify the changes in the mean and extreme climate across China when the 2°C, 3°C, and 4°C thresholds under different Representative Concentration Pathways (RCP) scenarios are exceeded. In general, the ASAT warms faster over China than the global mean in the 21st century. Extreme warm events (e.g., warm nights, warm days, and tropical nights) increase greatly, while extreme cold events (e.g., cold nights, cold days, and frost days) decrease. When the 4°C threshold is exceeded, warm nights index (spatially averaged over China) are projected to show an increase of about 49.9% relative to the reference period. Accompanied by the increase in global mean temperature, the northern part of China will see more precipitation when the 2°C threshold is exceeded. Extreme precipitation shows obvious intensification in both frequency and magnitude when different temperature thresholds are exceeded. China is dominated by lengthening heavy and very heavy precipitation days and increasing maximum consecutive 5-day precipitation and extremely wet days. Under the RCP8.5 scenario, the maximum consecutive 5-day precipitation amount increases by 12.5 mm and 17.0 mm when the global ASAT becomes 3°C and 4°C warmer, respectively. The changes are found to be more pronounced under higher temperature thresholds. Southwest China, however, exhibits larger changes in the magnitude of extreme precipitation than other regions.%本文基于耦合模式

  18. Sscience & technology review; Science Technology Review

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-07-01

    This review is published ten times a year to communicate, to a broad audience, Lawrence Livermore National Laboratory`s scientific and technological accomplishments, particularly in the Laboratory`s core mission areas - global security, energy and the environment, and bioscience and biotechnology. This review for the month of July 1996 discusses: Frontiers of research in advanced computations, The multibeam Fabry-Perot velocimeter: Efficient measurement of high velocities, High-tech tools for the American textile industry, and Rock mechanics: can the Tuff take the stress.

  19. Nigerian Journal of Technological Research

    African Journals Online (AJOL)

    The Nigerian Journal of Technological Research is a pure scientific journal with a ... technology to its immediate environs and the international community. ... and communication Technology; Management and Entrepreneurship sciences.

  20. Wind Technologies & Evolving Opportunities (Presentation)

    Energy Technology Data Exchange (ETDEWEB)

    Robichaud, R.

    2014-07-01

    This presentation covers opportunities for wind technology; wind energy market trends; an overview of the National Wind Technology Center near Boulder, Colorado; wind energy price and cost trends; wind turbine technology improvements; and wind resource characterization improvements.

  1. IT-BT convergence technology

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2012-12-15

    This book explains IT-BT convergence technology as the future technology, which includes a prolog, easy IT-BT convergence technology that has infinite potentials for new value, policy of IT-BT convergence technology showing the potential of smart Korea, IT-BT convergence opening happy future, for the new future of IT powerful nation Korea with IT-BT convergence technology and an epilogue. This book reveals the conception, policy, performance and future of IT-BT convergence technology.

  2. Mapping Technology Space by Normalizing Technology Relatedness Networks

    CERN Document Server

    Alstott, Jeff; Yan, Bowen; Luo, Jianxi

    2015-01-01

    Technology is a complex system, with technologies relating to each other in a space that can be mapped as a network. The technology relatedness network's structure can reveal properties of technologies and of human behavior, if it can be mapped accurately. Technology networks have been made from patent data, using several measures of relatedness. These measures, however, are influenced by factors of the patenting system that do not reflect technologies or their relatedness. We created technology networks that precisely controlled for these impinging factors and normalized them out, using data from 3.9 million patents. The normalized technology relatedness networks were sparse, with only ~20% of technology domain pairs more related than would be expected by chance. Different measures of technology relatedness became more correlated with each other after normalization, approaching a single dimension of technology relatedness. The normalized network corresponded with human behavior: we analyzed the patenting his...

  3. Environmental science and technology

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2014-07-01

    The Program on Environmental Science and Technology developed at the Chemical and Environmental Technology Center comprehends environmental chemistry (water, soil and atmospheric chemistry), clean technologies (desulfurization of diesel and oil, biodegradable polymers and structural modification of polymers, recycling, pyrolysis of dangerous chemicals by molten salt technology), nanotechnology (magnetic nanoparticles, dendrimers, nano biomarkers, catalysts) and chemical characterization of nuclear fuel and nuclear fuel cycle waste (chemical and isotopic characterization). The Chemical and Environmental Technology Center was established in 1995, as an evolution of the former Department of Chemistry Engineering (1970). The program on environment science and technology was structured as consequence of the continuous growth of environmental activities on areas related to nuclear programs of IPEN. Moreover, it was an answer to the society concerning the climate changes and biodiversity preservation. All activities of research and development, services, supervision of graduate and under graduated students and courses performance at the center were related to the development, improvement and establishment of new technologies. The highlights of this period (2011 - 2013) were: - Development and use of modern analytical technology for the characterization of persistent pollutants and endocrine disrupters (metals, PAHA’s, PCBs, Pesticides, hormones, surfactants, plasticizer and human pharmaceuticals) in order to evaluate water quality and/or sediments; - Atmospheric chemistry and greenhouse gases: Evaluating an estimation of surface trace gas fluxes from aircraft measurements above the Amazon; - Cooperation with SABESP (Water and Sewage Company) and CETESB (State Environment Agency) in program for the development of public policies; - Studies and development in biodegradable polymers, polyolefins and advanced methods for polymer and rubber recycling and re-use; - Studies

  4. Trusted Computing Technologies, Intel Trusted Execution Technology.

    Energy Technology Data Exchange (ETDEWEB)

    Guise, Max Joseph; Wendt, Jeremy Daniel

    2011-01-01

    We describe the current state-of-the-art in Trusted Computing Technologies - focusing mainly on Intel's Trusted Execution Technology (TXT). This document is based on existing documentation and tests of two existing TXT-based systems: Intel's Trusted Boot and Invisible Things Lab's Qubes OS. We describe what features are lacking in current implementations, describe what a mature system could provide, and present a list of developments to watch. Critical systems perform operation-critical computations on high importance data. In such systems, the inputs, computation steps, and outputs may be highly sensitive. Sensitive components must be protected from both unauthorized release, and unauthorized alteration: Unauthorized users should not access the sensitive input and sensitive output data, nor be able to alter them; the computation contains intermediate data with the same requirements, and executes algorithms that the unauthorized should not be able to know or alter. Due to various system requirements, such critical systems are frequently built from commercial hardware, employ commercial software, and require network access. These hardware, software, and network system components increase the risk that sensitive input data, computation, and output data may be compromised.

  5. Advanced Situation Awareness Technologies Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Advanced Situation Awareness Technologies (ASAT) will facilitate exploration of the moon surface, and other planetary bodies. This powerful technology will also find...

  6. Energetics Manufacturing Technology Center (EMTC)

    Data.gov (United States)

    Federal Laboratory Consortium — The Energetics Manufacturing Technology Center (EMTC), established in 1994 by the Office of Naval Research (ONR) Manufacturing Technology (ManTech) Program, is Navy...

  7. Methods and Technologies Branch (MTB)

    Science.gov (United States)

    The Methods and Technologies Branch focuses on methods to address epidemiologic data collection, study design and analysis, and to modify technological approaches to better understand cancer susceptibility.

  8. Society for Assisted Reproductive Technology

    Science.gov (United States)

    The Society for Assisted Reproductive Technology PATIENTS Patient Information What Is SART? Risks of IVF Third Party Reproduction A Patient's Guide to Assisted Reproductive Technology Frequently Asked ...

  9. Space Technology Research Grants Program

    Data.gov (United States)

    National Aeronautics and Space Administration — The Space Technology Research Grants Program will accelerate the development of "push" technologies to support the future space science and exploration...

  10. Ceramic Technology Project

    Energy Technology Data Exchange (ETDEWEB)

    1992-03-01

    The Ceramic Technology Project was developed by the USDOE Office of Transportation Systems (OTS) in Conservation and Renewable Energy. This project, part of the OTS's Materials Development Program, was developed to meet the ceramic technology requirements of the OTS's automotive technology programs. Significant accomplishments in fabricating ceramic components for the USDOE and NASA advanced heat engine programs have provided evidence that the operation of ceramic parts in high-temperature engine environments is feasible. These programs have also demonstrated that additional research is needed in materials and processing development, design methodology, and data base and life prediction before industry will have a sufficient technology base from which to produce reliable cost-effective ceramic engine components commercially. A five-year project plan was developed with extensive input from private industry. In July 1990 the original plan was updated through the estimated completion of development in 1993. The objective is to develop the industrial technology base required for reliable ceramics for application in advanced automotive heat engines. The project approach includes determining the mechanisms controlling reliability, improving processes for fabricating existing ceramics, developing new materials with increased reliability, and testing these materials in simulated engine environments to confirm reliability. Although this is a generic materials project, the focus is on the structural ceramics for advanced gas turbine and diesel engines, ceramic bearings and attachments, and ceramic coatings for thermal barrier and wear applications in these engines. To facilitate the rapid transfer of this technology to US industry, the major portion of the work is being done in the ceramic industry, with technological support from government laboratories, other industrial laboratories, and universities.

  11. Technologies for lake restoration

    Directory of Open Access Journals (Sweden)

    Helmut KLAPPER

    2003-09-01

    Full Text Available Lakes are suffering from different stress factors and need to be restored using different approaches. The eutrophication remains as the main water quality management problem for inland waters: both lakes and reservoirs. The way to curb the degradation is to stop the nutrient sources and to accelerate the restoration with help of in-lake technologies. Especially lakes with a long retention time need (eco- technological help to decrease the nutrient content in the free water. The microbial and other organic matter from sewage and other autochthonous biomasses, causes oxygen depletion, which has many adverse effects. In less developed countries big reservoirs function as sewage treatment plants. Natural aeration solves problems only partly and many pollutants tend to accumulate in the sediments. The acidification by acid rain and by pyrite oxidation has to be controlled by acid neutralizing technologies. Addition of alkaline chemicals is useful only for soft waters, and technologies for (microbial alkalinization of very acidic hardwater mining lakes are in development. The corrective measures differ from those in use for eutrophication control. The salinization and water shortage mostly occurs if more water is used than available. L. Aral, L. Tschad, the Dead Sea or L. Nasser belong to waters with most severe environmental problems on a global scale. Their hydrologic regime needs to be evaluated. The inflow of salt water at the bottom of some mining lakes adds to stability of stratification, and thus accumulation of hydrogen sulphide in the monimolimnion of the meromictic lakes. Destratification, which is the most used technology, is only restricted applicable because of the dangerous concentrations of the byproducts of biological degradation. The contamination of lakes with hazardous substances from industry and agriculture require different restoration technologies, including subhydric isolation and storage, addition of nutrients for better self

  12. Securing smart grid technology

    Science.gov (United States)

    Chaitanya Krishna, E.; Kosaleswara Reddy, T.; Reddy, M. YogaTeja; Reddy G. M., Sreerama; Madhusudhan, E.; AlMuhteb, Sulaiman

    2013-03-01

    In the developing countries electrical energy is very important for its all-round improvement by saving thousands of dollars and investing them in other sector for development. For Growing needs of power existing hierarchical, centrally controlled grid of the 20th Century is not sufficient. To produce and utilize effective power supply for industries or people we should have Smarter Electrical grids that address the challenges of the existing power grid. The Smart grid can be considered as a modern electric power grid infrastructure for enhanced efficiency and reliability through automated control, high-power converters, modern communications infrastructure along with modern IT services, sensing and metering technologies, and modern energy management techniques based on the optimization of demand, energy and network availability and so on. The main objective of this paper is to provide a contemporary look at the current state of the art in smart grid communications as well as critical issues on smart grid technologies primarily in terms of information and communication technology (ICT) issues like security, efficiency to communications layer field. In this paper we propose new model for security in Smart Grid Technology that contains Security Module(SM) along with DEM which will enhance security in Grid. It is expected that this paper will provide a better understanding of the technologies, potential advantages and research challenges of the smart grid and provoke interest among the research community to further explore this promising research area.

  13. Technology Roadmap: Energy Storage

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2014-03-01

    Energy storage technologies are valuable components in most energy systems and could be an important tool in achieving a low-carbon future. These technologies allow for the decoupling of energy supply and demand, in essence providing a valuable resource to system operators. There are many cases where energy storage deployment is competitive or near-competitive in today's energy system. However, regulatory and market conditions are frequently ill-equipped to compensate storage for the suite of services that it can provide. Furthermore, some technologies are still too expensive relative to other competing technologies (e.g. flexible generation and new transmission lines in electricity systems). One of the key goals of this new roadmap is to understand and communicate the value of energy storage to energy system stakeholders. This will include concepts that address the current status of deployment and predicted evolution in the context of current and future energy system needs by using a ''systems perspective'' rather than looking at storage technologies in isolation.

  14. Small engine technology programs

    Science.gov (United States)

    Niedzwiecki, Richard W.

    1990-01-01

    Described here is the small engine technology program being sponsored at the Lewis Research Center. Small gas turbine research is aimed at general aviation, commuter aircraft, rotorcraft, and cruise missile applications. The Rotary Engine program is aimed at supplying fuel flexible, fuel efficient technology to the general aviation industry, but also has applications to other missions. The Automotive Gas Turbine (AGT) and Heavy-Duty Diesel Transport Technology (HDTT) programs are sponsored by DOE. The Compound Cycle Engine program is sponsored by the Army. All of the programs are aimed towards highly efficient engine cycles, very efficient components, and the use of high temperature structural ceramics. This research tends to be generic in nature and has broad applications. The HDTT, rotary technology, and the compound cycle programs are all examining approaches to minimum heat rejection, or 'adiabatic' systems employing advanced materials. The AGT program is also directed towards ceramics application to gas turbine hot section components. Turbomachinery advances in the gas turbine programs will benefit advanced turbochargers and turbocompounders for the intermittent combustion systems, and the fundamental understandings and analytical codes developed in the research and technology programs will be directly applicable to the system projects.

  15. Transmutation Technology Development

    Energy Technology Data Exchange (ETDEWEB)

    Song, T. Y.; Park, W. S.; Kim, Y. H. (and others)

    2007-06-15

    The spent fuel coming from the PWR is one of the most difficult problems to be solved for the continuous use of nuclear power. It takes a few million years to be safe under the ground. Therefore, it is not easy to take care of the spent fuel for such a long time. Transmutation technology is the key technology which can solve the spent fuel problem basically. Transmutation is to transmute long-lived radioactive nuclides in the spent fuel into short-lived or stable nuclide through nuclear reactions. The long-lived radioactive nuclides can be TRU and fission products such as Tc-99 and I-129. Although the transmutation technology does not make the underground disposal totally unnecessary, the period to take care of the spent fuel can be reduced to the order of a few hundred years. In addition to the environmental benefit, transmutation can be considered to recycle the energy in the spent fuel since the transmutation is performed through nuclear fission reaction of the TRU in the spent fuel. Therefore, transmutation technology is worth being developed in economical aspect. The results of this work can be a basis for the next stage research. The objective of the third stage research was to complete the core conceptual design and verification of the key technologies. The final results will contribute to the establishment of Korean back end fuel cycle policy by providing technical guidelines.

  16. Technology transfer within the telecare technology innovation system

    NARCIS (Netherlands)

    Vlies, R.D. van der; Felix, E.

    2013-01-01

    Telecare technology is not common yet, although it is perceived as promising. Most studies on telecare technology transfer present a case involving the use of a single methodology and approach during some steps of technology transfer. Technology transfer models cannot be sensibly constructed if they

  17. Philosophy of Technology Assumptions in Educational Technology Leadership

    Science.gov (United States)

    Webster, Mark David

    2017-01-01

    A qualitative study using grounded theory methods was conducted to (a) examine what philosophy of technology assumptions are present in the thinking of K-12 technology leaders, (b) investigate how the assumptions may influence technology decision making, and (c) explore whether technological determinist assumptions are present. Subjects involved…

  18. Mini Technology Manual for Schools: An Introduction to Technology Integration

    Science.gov (United States)

    Grismore, Brian A.

    2012-01-01

    The purpose of this manual is to assist school leaders in beginning or developing the use of educational technology within their school or district. The manual covers topics: 1) advantages of educational technology; 2) types of technology used for learning and teaching; 3) how to make good decisions about the use of technology in schools; 4) the…

  19. Philosophy of Technology Assumptions in Educational Technology Leadership

    Science.gov (United States)

    Webster, Mark David

    2017-01-01

    A qualitative study using grounded theory methods was conducted to (a) examine what philosophy of technology assumptions are present in the thinking of K-12 technology leaders, (b) investigate how the assumptions may influence technology decision making, and (c) explore whether technological determinist assumptions are present. Subjects involved…

  20. Understanding Technology Literacy: A Framework for Evaluating Educational Technology Integration

    Science.gov (United States)

    Davies, Randall S.

    2011-01-01

    Federal legislation in the United States currently mandates that technology be integrated into school curricula because of the popular belief that learning is enhanced through the use of technology. The challenge for educators is to understand how best to teach with technology while developing the technological expertise of their students. This…

  1. Technology Transfer Issues and a New Technology Transfer Model

    Science.gov (United States)

    Choi, Hee Jun

    2009-01-01

    The following are major issues that should be considered for efficient and effective technology transfer: conceptions of technology, technological activity and transfer, communication channels, factors affecting transfer, and models of transfer. In particular, a well-developed model of technology transfer could be used as a framework for…

  2. Dielectric heating. Technologies; Chauffage dielectrique. Technologies

    Energy Technology Data Exchange (ETDEWEB)

    Roussy, G. [Universite Henri-Poincare, Dir. de Recherche, 54 - Nancy (France); Rochas, J.F. [Societe Sairem, 69 - Lyon (France); Oberlin, C. [Electricite de France (EDF), 75 - Paris (France)

    2003-08-01

    The electrothermal heating processes are of two types: the indirect heating (indirect resistance, infrared, indirect arc and plasma heating) in which the energy transfer from the source to the receptor complies with the usual thermal laws, and the direct heating (direct ohmic, induction, high-frequency, microwave, electron bombardment, laser and direct arc heating) in which the receptor is crossed by an electric current which generates a heat release inside the receptor. This paper treats of the technologies used in high frequency and microwave heating: 1 - techniques of implementation of high-frequency (HF) heating: HF generator, energy transmission line, HF applicator, impedance adjustment system, auxiliary devices; 2 - techniques of implementation of microwave heating: microwave generator, wave guide, microwave applicator, impedance adjustment circuit, auxiliary devices. (J.S.)

  3. Wind energy technology developments

    DEFF Research Database (Denmark)

    Madsen, Peter Hauge; Hansen, Morten Hartvig; Pedersen, Niels Leergaard

    2014-01-01

    turbine blades and towers are very large series-produced components, which costs and quality are strongly dependent on the manufacturing methods. The industrial wind energy sector is well developed in Denmark, and the competitive advantage of the Danish sector and the potential for job creation......This chapter describes the present mainstream development of the wind turbine technology at present. The turbine technology development trend is characterized by up-scaling to turbines with larger capacity for both onshore and offshore applications, larger rotors and new drivetrain solution......, including the direct-drive solution without gearbox. The technology solutions are strongly influenced by the development of the international industry with a global market for components and a trend towards a “shared” development effort in collaboration between the OEM’s and component sub-suppliers. Wind...

  4. Technology and Sport

    DEFF Research Database (Denmark)

    Møller, Rasmus Bysted; Møller, Verner

    2015-01-01

    The relationship between sport and technology is close and can be both fruitful and destructive. Technology has a constitutive function in sport as it makes the activity possible and it can enhance performance as well as the sporting experience. The use of football boots is clearly more comfortable...... and effective than playing in bare feet in a game of football. However, sport challenges its athletes by demanding the employment of less efficient means rather than more efficient means in pursuit of sport specific goals. Therefore technology can potentially subtract from the sporting experience and even...... threaten the internal logic of sport. If as an example very efficient hail cartridges were allowed for use in double trap shooting it would reduce the skills required to excel at that discipline reducing its value for participants and spectators alike. The use of forbidden performance enhancing substances...

  5. Drying and energy technologies

    CERN Document Server

    Lima, A

    2016-01-01

    This book provides a comprehensive overview of essential topics related to conventional and advanced drying and energy technologies, especially motivated by increased industry and academic interest. The main topics discussed are: theory and applications of drying, emerging topics in drying technology, innovations and trends in drying, thermo-hydro-chemical-mechanical behaviors of porous materials in drying, and drying equipment and energy. Since the topics covered are inter- and multi-disciplinary, the book offers an excellent source of information for engineers, energy specialists, scientists, researchers, graduate students, and leaders of industrial companies. This book is divided into several chapters focusing on the engineering, science and technology applied in essential industrial processes used for raw materials and products.

  6. Technology Roadmap: Hydropower

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2012-07-01

    Hydropower could double its contribution by 2050, reaching 2,000 GW of global capacity and over 7,000 TWh. This achievement, driven primarily by the quest of clean electricity, could prevent annual emissions of up to 3 billion tonnes of CO2 from fossil-fuel plants. The bulk of this growth would come from large plants in emerging economies and developing countries. Hydroelectricity’s many advantages include reliability, proven technology, large storage capacity, and very low operating and maintenance costs. Hydropower is highly flexible, a precious asset for electricity network operators, especially given rapid expansion of variable generation from other renewable energy technologies such as wind power and photovoltaics. Many hydropower plants also provide flood control, irrigation, navigation and freshwater supply. The technology roadmap for Hydropower details action needed from policy makers to allow hydroelectric production to double, and addresses necessary conditions, including resolving environmental issues and gaining public acceptance.

  7. Electron Technology: ELTE 2016

    Science.gov (United States)

    Pisarkiewicz, Tadeusz; Kucewicz, Wojciech

    2016-12-01

    In this paper we present a review of research results and technical accomplishments presented by researchers from technical universities, governmental institutes and research companies during the XIIth Scientific Conference Electron Technology, ELTE 2016. This review is based on materials presented at four topical conference sessions: Microelectronics and Nanoelectronics, Photonics, Materials and Technologies, and Microsystems and also on materials presented by invited speakers at two dedicated sessions. Oral sessions were accompanied by the poster sessions. In effect about 50 papers gathered in this volume reflect the topics discussed at the Conference. A short description of technological and measurement possibilities in the laboratories of Academic Centre for Materials and Nanotechnology and also in the Department of Electronics of the Faculty of Computer Science, Electronics and Telecommunications AGH UST are given.

  8. Multi-technology positioning

    CERN Document Server

    Lohan, Elena-Simona; Wymeersch, Henk; Seco-Granados, Gonzalo; Nykänen, Ossi

    2017-01-01

    This book provides an overview of positioning technologies, applications and services in a format accessible to a wide variety of readers. Readers who have always wanted to understand how satellite-based positioning, wireless network positioning, inertial navigation, and their combinations work will find great value in this book. Readers will also learn about the advantages and disadvantages of different positioning methods, their limitations and challenges. Cognitive positioning, adding the brain to determine which technologies to use at device runtime, is introduced as well. Coverage also includes the use of position information for Location Based Services (LBS), as well as context-aware positioning services, designed for better user experience. • Brings understanding of positioning technology to readers from a variety of disciplines • Reviews multiple techniques, providing insight on the pros, cons and challenges related to each • Designed to be a tutorial on basic principles, avoiding unnecessary de...

  9. Technologic advances in endodontics.

    Science.gov (United States)

    Mortman, Rory E

    2011-07-01

    This article addresses technologic advances in endodontics pertaining to new and emerging technology. Cone-beam computed tomography and optical occurrence tomography are 2 new imaging technologies that can assist the practitioner in the diagnosis of pulpal disease. The self-adjusting file and the Apexum device can be used for instrumentation and bulk debridement of an apical lesion, respectively. Neodymium:yttrium-aluminum-garnet laser, erbium:chromium:yttrium-scandium-gallium-garnet laser, EndoActivator, EndoVac, and light-activated disinfection may assist the practitioner in cleaning the root canal system. Computed tomography-guided surgery shows promise in making endodontic surgery easier, as does mineral trioxide aggregate cement for regenerative endodontic procedures.

  10. Technology or Process First?

    DEFF Research Database (Denmark)

    Siurdyban, Artur Henryk; Svejvig, Per; Møller, Charles

    Enterprise Systems Management (ESM) and Business Pro- cess Management (BPM), although highly correlated, have evolved as alternative and mutually exclusive approaches to corporate infrastruc- ture. As a result, companies struggle to nd the right balance between technology and process factors...... in infrastructure implementation projects. The purpose of this paper is articulate a need and a direction to medi- ate between the process-driven and the technology-driven approaches. Using a cross-case analysis, we gain insight into two examples of sys- tems and process implementation. We highlight the dierences...... between them using strategic alignment, Enterprise Systems and Business Process Management theories. We argue that the insights from these cases can lead to a better alignment between process and technology. Implications for practice include the direction towards a closer integration of process...

  11. Minerals in environmental technology

    Energy Technology Data Exchange (ETDEWEB)

    Schuiling, R.D. [Utrecht Univ., Utrecht (Netherlands). Faculty of Earth Sciences

    2000-07-01

    Minerals play a key role in the environment; this role is often not well understood, because the emphasis of most environmentalists is on air, water, or the composition of solid wastes as a whole, without paying attention to their mineralogical composition. Several minerals can serve as effective and cheap adsorbents for many toxic chemicals. Several minerals can be used as a cheap substitute for expensive chemicals in environmental technologies. Environmental technologies that produce an economically interesting mineral will have an edge over competing technologies. Most of the problems, overreaction, panicky and expensive measures with regard to exposure from quartz and asbestos stem from a poor understanding of natural levels of common contaminants, a disregard for mineralogy, and a lack of insight into natural processes in general.

  12. Metalcasting Industry Technology Roadmap

    Energy Technology Data Exchange (ETDEWEB)

    none,

    1998-01-01

    The Roadmap sets out the strategy for pursuing near-, mid-, and long-term goals set out by industry and for carrying out the cooperative agreement between the U.S. Department of Energy and industry. The Roadmap outlines key goals for products and markets, materials technology, manufacturing technology, environmental technology, human resources, and industry health programs. The Roadmap sets out the strategy for pursuing near-, mid-, and long-term goals set out by industry and for carrying out the cooperative agreement between the U.S. Department of Energy and industry. The Roadmap sets out the strategy for pursuing near-, mid-, and long-term goals set out by industry and for carrying out the cooperative agreement between the U.S. Department of Energy and industry.

  13. Cell-SELEX Technology

    Science.gov (United States)

    2012-01-01

    Abstract Aptamers are molecules identified from large combinatorial nucleic acid libraries by their high affinity to target molecules. Due to a variety of desired properties, aptamers are attractive alternatives to antibodies in molecular biology and medical applications. Aptamers are identified through an iterative selection–amplification process known as systematic evolution of ligands by exponential enrichment (SELEX). Although SELEX is typically carried out using purified target molecules, whole live cells are also employable as selection targets. This technology, Cell-SELEX, has several advantages. For example, generated aptamers are functional with a native conformation of the target molecule on live cells, and thus, cell surface transmembrane proteins would be targets even when their purifications in native conformations are difficult. In addition, cell-specific aptamers can be obtained without any knowledge about cell surface molecules on the target cells. Here, I review the progress of Cell-SELEX technology and discuss advantages of the technology. PMID:23515081

  14. Technological Aspects: High Voltage

    CERN Document Server

    Faircloth, D C

    2013-01-01

    This paper covers the theory and technological aspects of high-voltage design for ion sources. Electric field strengths are critical to understanding high-voltage breakdown. The equations governing electric fields and the techniques to solve them are discussed. The fundamental physics of high-voltage breakdown and electrical discharges are outlined. Different types of electrical discharges are catalogued and their behaviour in environments ranging from air to vacuum are detailed. The importance of surfaces is discussed. The principles of designing electrodes and insulators are introduced. The use of high-voltage platforms and their relation to system design are discussed. The use of commercially available high-voltage technology such as connectors, feedthroughs and cables are considered. Different power supply technologies and their procurement are briefly outlined. High-voltage safety, electric shocks and system design rules are covered.

  15. Developing human technology curriculum

    Directory of Open Access Journals (Sweden)

    Teija Vainio

    2012-10-01

    Full Text Available During the past ten years expertise in human-computer interaction has shifted from humans interacting with desktop computers to individual human beings or groups of human beings interacting with embedded or mobile technology. Thus, humans are not only interacting with computers but with technology. Obviously, this shift should be reflected in how we educate human-technology interaction (HTI experts today and in the future. We tackle this educational challenge first by analysing current Master’s-level education in collaboration with two universities and second, discussing postgraduate education in the international context. As a result, we identified core studies that should be included in the HTI curriculum. Furthermore, we discuss some practical challenges and new directions for international HTI education.

  16. Technology transfer 1995

    Energy Technology Data Exchange (ETDEWEB)

    1995-01-01

    Technology Transfer 1995 is intended to inform the US industrial and academic sectors about the many opportunities they have to form partnerships with the US Department of Energy (DOE) for the mutual advantage of the individual institutions, DOE, and the nation as a whole. It also describes some of the growing number of remarkable achievements resulting from such partnerships. These partnership success stories offer ample evidence that Americans are learning how to work together to secure major benefits for the nation--by combining the technological, scientific, and human resources resident in national laboratories with those in industry and academia. The benefits include more and better jobs for Americans, improved productivity and global competitiveness for technology-based industries, and a more efficient government laboratory system.

  17. Hybrid propulsion technology program

    Science.gov (United States)

    1990-01-01

    Technology was identified which will enable application of hybrid propulsion to manned and unmanned space launch vehicles. Two design concepts are proposed. The first is a hybrid propulsion system using the classical method of regression (classical hybrid) resulting from the flow of oxidizer across a fuel grain surface. The second system uses a self-sustaining gas generator (gas generator hybrid) to produce a fuel rich exhaust that was mixed with oxidizer in a separate combustor. Both systems offer cost and reliability improvement over the existing solid rocket booster and proposed liquid boosters. The designs were evaluated using life cycle cost and reliability. The program consisted of: (1) identification and evaluation of candidate oxidizers and fuels; (2) preliminary evaluation of booster design concepts; (3) preparation of a detailed point design including life cycle costs and reliability analyses; (4) identification of those hybrid specific technologies needing improvement; and (5) preperation of a technology acquisition plan and large scale demonstration plan.

  18. Small Artifacts - Big Technologies

    DEFF Research Database (Denmark)

    Kreiner, Kristian

    2005-01-01

    The computer IC is the heart of the information and telecommunication technology. It is a tiny artifact, but with incredible organizing powers. We use this physical artifact as the location for studying central problems of the knowledge economy. First, the paper describes the history of chip design...... and the emergence of the technological community involved in designing and manufacturing computer chips. The community is structured in a way that reflects the underlying physical nature silicon and the numerous other materials and chemicals involved. But it also reflects the human agency of defining new projects...... instrument. It is found that technological progress is not hindered, but rather aided by the use of imperfect principles, abstractions and representations of reality. The power of such imperfections is discussed and generalized....

  19. IGCC technology and demonstration

    Energy Technology Data Exchange (ETDEWEB)

    Palonen, J. [A. Ahlstrom Corporation, Karhula (Finland). Hans Ahlstrom Lab.; Lundqvist, R.G. [A. Ahlstrom Corporation, Helsinki (Finland); Staahl, K. [Sydkraft AB, Malmoe (Sweden)

    1996-12-31

    Future energy production will be performed by advanced technologies that are more efficient, more environmentally friendly and less expensive than current technologies. Integrated gasification combined cycle (IGCC) power plants have been proposed as one of these systems. Utilising biofuels in future energy production will also be emphasised since this lowers substantially carbon dioxide emissions into the atmosphere due to the fact that biomass is a renewable form of energy. Combining advanced technology and biomass utilisation is for this reason something that should and will be encouraged. A. Ahlstrom Corporation of Finland and Sydkraft AB of Sweden have as one part of company strategies adopted this approach for the future. The companies have joined their resources in developing a biomass-based IGCC system with the gasification part based on pressurised circulating fluidized-bed technology. With this kind of technology electrical efficiency can be substantially increased compared to conventional power plants. As a first concrete step, a decision has been made to build a demonstration plant. This plant, located in Vaernamo, Sweden, has already been built and is now in commissioning and demonstration stage. The system comprises a fuel drying plant, a pressurised CFB gasifier with gas cooling and cleaning, a gas turbine, a waste heat recovery unit and a steam turbine. The plant is the first in the world where the integration of a pressurised gasifier with a gas turbine will be realised utilising a low calorific gas produced from biomass. The capacity of the Vaernamo plant is 6 MW of electricity and 9 MW of district heating. Technology development is in progress for design of plants of sizes from 20 to 120 MWe. The paper describes the Bioflow IGCC system, the Vaernamo demonstration plant and experiences from the commissioning and demonstration stages. (orig.)

  20. CONVERGENCE OF TECHNOLOGIES

    Directory of Open Access Journals (Sweden)

    R. Siriram

    2012-01-01

    Full Text Available

    ENGLISH ABSTRACT: Technology is a catalyst for competitive advantage. However, it is how technology is used that leads to a firm’s improved performance. In this article, an investigative framework is constructed to understand better what strategically drives new technology adoption. The strategic drivers include technology and business strategy alignment, better technology planning and selection of new technologies, the effects on a firm’s culture and climate, links to a firm’s organisational and environmental evolution, and benefits through convergence and collaboration. Using an investigative framework, it is shown how the strategic drivers link to improve a firm’s performance, producing competitive advantage. The investigative framework is tested using structural equation modelling. Various hypotheses are formed, and recommendations for further research are made.

    AFRIKAANSE OPSOMMING: Tegnologie is ‘n katalisator vir mededingende voordeel. Dit is egter hoe tegnologie aangewend word wat aanleiding gee tot ‘n onderneming se verbeterde prestasie. In hierdie artikel word ‘n ondersoekende raamwerk gekonstrueer om insig te kry in dit wat die aanvaarding van nuwe tegnologie strategies dryf. Die strategiese dryfvere sluit in die belyning van tegnologie en ondernemingstrategie, beter tegnologiebeplanning en seleksie van nuwe tegnologieë, die effek op ‘n onderneming se kultuur en klimaat, koppeling na ‘n onderneming se organisatoriese en omgewingsevolusie, en voordele verkry deur konvergensie en samewerking. Deur ‘n ondersoekende raamwerk te gebruik, word daar getoon dat die strategiese dryfvere koppel om ‘n onderneming se prestasie te verbeter en sodoende ‘n mededingende voordeel te skep. Die raamwerk word getoets en hipoteses geformuleer waarna aanbevelings oor verdere navorsing aan die hand gedoen word.