Airborne Measurements in Support of the NASA Atmospheric Carbon and Transport - America (ACT-America) Mission

Science.gov (United States)

Meadows, Byron; Davis, Ken; Barrick, John; Browell, Edward; Chen, Gao; Dobler, Jeremy; Fried, Alan; Lauvaux, Thomas; Lin, Bing; McGill, Matt;

The InSAeS4 Airborne X-Band Interferometric SAR System: A First Assessment on Its Imaging and Topographic Mapping Capabilities

Directory of Open Access Journals (Sweden)

Stefano Perna

2016-01-01

Full Text Available We present in this work a first assessment of the imaging and topographic mapping capabilities of the InSAeS4 system, which is a single-pass interferometric airborne X-Band Synthetic Aperture Radar (SAR. In particular, we first provide a brief description of the InSAeS4 sensor. Then, we discuss the results of our analysis on the SAR and interferometric SAR products relevant to the first flight-test campaign. More specifically, we have exploited as reference the GPS measurements relevant to nine Corner Reflectors (CRs deployed over the illuminated area during the campaign and a laser scanner Digital Elevation Model (DEM. From the analysis carried out on the CRs we achieved a mean geometric resolution, for the SAR products, of about 0.14 m in azimuth and 0.49 m in range, a positioning misalignment with standard deviation of 0.07 m in range and 0.08 m in azimuth, and a height error with standard deviation of 0.51 m. From the comparison with the laser scanner DEM we estimated a height error with standard deviation of 1.57 m.

Aerial radiometric and magnetic survey: Woodward National Topographic Map, Oklahoma, West Texas project

International Nuclear Information System (INIS)

1980-05-01

The results of analyses of the airborne gamma radiation and total magnetic field survey flown for the region identified as the Woodward National Topographic Map NJ14-11 are presented. The airborne data gathered are reduced by ground computer facilities to yield profile plots of the basic uranium, thorium and potassium equivalent gamma radiation intensities, ratios of these intensities, aircraft altitude above the earth's surface, total gamma ray and earth's magnetic field intensity, correlated as a function of geologic units. The distribution of data within each geologic unit, for all surveyed map lines and tie lines, has been calculated and is included. Two sets of profiled data for each line are included, with one set displaying the above-cited data. The second set includes only flight line magnetic field, temperature, pressure, altitude data plus magnetic field data as measured at a base station. A general description of the area, including descriptions of the various geologic units and the corresponding airborne data, is included also

Aerial radiometric and magnetic survey: Winchester National topographic map, Kentucky. Southeast US project

International Nuclear Information System (INIS)

1980-01-01

The results of analyses of the airborne gamma radiation and total magnetic field survey flown for the region identified as the Winchester National Topographic Map NJ16-9 are presented. The airborne data gathered are reduced by ground computer facilities to yield profile plots of the basic uranium, thorium and potassium equivalent gamma radiation intensities, ratios of these intensities, aircraft altitude above the earth's surface, total gamma ray and earth's magnetic field intensity, correlated as a function of geologic units. The distribution of data within each geologic unit, for all surveyed map lines and tie lines, has been calculated and is included. Two sets of profiled data for each line are included, with one set displaying the above-cited data. The second set includes only flight line magnetic field, temperature, pressure, altitude data plus magnetic field data as measured at a base station. A general description of the area, including descriptions of the various geologic units and the corresponding airborne data, is included also

Aerial radiometric and magnetic survey: San Antonio National Topographic Map, Texas. Final report

International Nuclear Information System (INIS)

1980-05-01

The results of analyses of the airborne gamma radiation and total magnetic field survey flown for the region identified as the San Antonio National Topographic Map NH14-8 are presented. The airborne data gathered are reduced by ground computer facilities to yield profile plots of the basic uranium, thorium, and potassium equivalent gamma radiation intensities, ratios of these intensities, aircraft altitude above the earth's surface, total gamma ray and earth's magnetic field intensity, correlated as a function of geologic units. The distribution of data within each geologic unit, for all surveyed map lines and tie lines, has been calculated and is included. Two sets of profiled data for each line are included, with one set displaying the above-cited data. The second set includes only flight line magnetic field, temperature, pressure, altitude data plus magnetic field data as measured at a base station. A general description of the area, including descriptions of the various geologic units and the corresponding airborne data, is included also

Aerial radiometric and magnetic survey: Quincy National Topographic map, Illinois/Missouri. Final report

International Nuclear Information System (INIS)

1981-01-01

The results of analyses of the airborne gamma radiation and total magnetic field survey flown for the region identified as the Quincy National Topographic Map NJ15-3 is presented in this report. The airborne data gathered is reduced by ground computer facilities to yield profile plots of the basic uranium, thorium and potassium equivalent gamma radiation intensities, ratios of these intensities, aircraft altitude above the earth's surface, total gamma ray and earth's magnet field intensity, correlated as a function of geologic units. The distribution of data within each geologic unit, for all surveyed map lines and tie lines, has been calculated and is included. Two sets of profiled data for each line are included, with one set displaying the above-cited data. The second set includes only flight line magnetic field, temperature, pressure, altitude data plus magnetic field data as measured at a base station. A general description of the area, including descriptions of the various geologic units and the corresponding airborne data, is included also

Derivation of Ground Surface and Vegetation in a Coastal Florida Wetland with Airborne Laser Technology

Science.gov (United States)

Raabe, Ellen A.; Harris, Melanie S.; Shrestha, Ramesh L.; Carter, William E.

2008-01-01

The geomorphology and vegetation of marsh-dominated coastal lowlands were mapped from airborne laser data points collected on the Gulf Coast of Florida near Cedar Key. Surface models were developed using low- and high-point filters to separate ground-surface and vegetation-canopy intercepts. In a non-automated process, the landscape was partitioned into functional landscape units to manage the modeling of key landscape features in discrete processing steps. The final digital ground surface-elevation model offers a faithful representation of topographic relief beneath canopies of tidal marsh and coastal forest. Bare-earth models approximate field-surveyed heights by + 0.17 m in the open marsh and + 0.22 m under thick marsh or forest canopy. The laser-derived digital surface models effectively delineate surface features of relatively inaccessible coastal habitats with a geographic coverage and vertical detail previously unavailable. Coastal topographic details include tidal-creek tributaries, levees, modest topographic undulations in the intertidal zone, karst features, silviculture, and relict sand dunes under coastal-forest canopy. A combination of laser-derived ground-surface and canopy-height models and intensity values provided additional mapping capabilities to differentiate between tidal-marsh zones and forest types such as mesic flatwood, hydric hammock, and oak scrub. Additional derived products include fine-scale shoreline and topographic profiles. The derived products demonstrate the capability to identify areas of concern to resource managers and unique components of the coastal system from laser altimetry. Because the very nature of a wetland system presents difficulties for access and data collection, airborne coverage from remote sensors has become an accepted alternative for monitoring wetland regions. Data acquisition with airborne laser represents a viable option for mapping coastal topography and for evaluating habitats and coastal change on marsh

Aerial radiometric and magnetic survey: Death Valley National Topographic Map, Nevada, California

International Nuclear Information System (INIS)

1979-01-01

The results of analysis of the airborne gamma radiation survey flown for the region identified as the Death Valley National Topographic Map NJ11-11 is presented in the bound Volume of this report. The airborne data gathered are reduced by ground computer facilities to yield profile plots of the basic uranium, thorium and potassium equivalent gamma radiation intensities, ratios of these intensities, aircraft altitude above the earth's surface, total gamma ray and earth's magnetic field intensity, correlated as a function of geologic units. The distribution of data within each geologic unit, for all surveyed map lines and tie lines, has been calculated and is included. Two sets of profiled data for each line are included with one set displaying the above-cited data. The second set includes only flight line magnetic field, temperature, pressure, altitude data plus magnetic field data as measured at a base station. A general description of the area, including descriptions of the various geologic units and the corresponding airborne data, is included also

Typical Applications of Airborne LIDAR Technolagy in Geological Investigation

Science.gov (United States)

Zheng, X.; Xiao, C.

2018-05-01

The technology of airborne light detection and ranging (LiDAR), also referred to as Airborne Laser Scanning, is widely used for high-resolution topographic data acquisition (even under forest cover) with sub-meter planimetric and vertical accuracy. This contribution constructs the real digital terrain model to provide the direct observation data for the landscape analysis in geological domains. Based on the advantage of LiDAR, the authors mainly deal with the applications of LiDAR data to such fields as surface land collapse, landslide and fault structure extraction. The review conclusion shows that airborne LiDAR technology is becoming an indispensable tool for above mentioned issues, especially in the local and large scale investigations of micro-topography. The technology not only can identify the surface collapse, landslide boundary and subtle faulted landform, but also be able to extract the filling parameters of collapsed surface, the geomorphic parameters of landslide stability evaluation and cracks. This technology has extensive prospect of applications in geological investigation.

TYPICAL APPLICATIONS OF AIRBORNE LIDAR TECHNOLAGY IN GEOLOGICAL INVESTIGATION

Directory of Open Access Journals (Sweden)

X. Zheng

2018-05-01

Full Text Available The technology of airborne light detection and ranging (LiDAR, also referred to as Airborne Laser Scanning, is widely used for high-resolution topographic data acquisition (even under forest cover with sub-meter planimetric and vertical accuracy. This contribution constructs the real digital terrain model to provide the direct observation data for the landscape analysis in geological domains. Based on the advantage of LiDAR, the authors mainly deal with the applications of LiDAR data to such fields as surface land collapse, landslide and fault structure extraction. The review conclusion shows that airborne LiDAR technology is becoming an indispensable tool for above mentioned issues, especially in the local and large scale investigations of micro-topography. The technology not only can identify the surface collapse, landslide boundary and subtle faulted landform, but also be able to extract the filling parameters of collapsed surface, the geomorphic parameters of landslide stability evaluation and cracks. This technology has extensive prospect of applications in geological investigation.

Aerial radiometric and magnetic survey: Perryton National Topographic Map, Texas/Oklahoma/Kansas. Final report

International Nuclear Information System (INIS)

1980-05-01

The results of analyses of the airborne gamma radiation and total magnetic field survey flown for the region identified as the Perryton National Topographic Map NJ14-10 are presented. The airborne data gathered are reduced by ground computer facilities to yield profile plots of the basic uranium, thorium and potassium equivalent gamma radiation intensities, ratios of these intensities, aircraft altitude above the earth's surface, total gamma ray and earth's magnetic field intensity, correlated as a function of geologic units. The distribution of data within each geologic unit, for all surveyed map lines and tie lines, has been calculated and is included. Two sets of profiled data for each line are included, with one set displaying the above-cited data. The second set includes only flight line magnetic field, temperature, pressure, altitude data plus magnetic field data as measured at a base station. A general description of the area, including descriptions of the various geologic units and the corresponding airborne data, is included also

Landscape-scale tropical forest dynamics: Relating canopy traits and topographically derived hydrologic indices in a floodplain system using CAO-AToMS

Science.gov (United States)

Chadwick, K.; Asner, G. P.

2012-12-01

The geomorphology of floodplains in the humid tropics has been used to infer basic classifications of forest types. However, analysis of the landscape-scale topographic and hydrologic patterns underpinning spatial variation in forest composition and function remain elusive due to the sparse coverage of forest plots, coarse resolution remotely sensed data, and the challenges of collecting first order hydrologic data. Airborne remote measurements provide an opportunity to consider the relationship between high-resolution topographic and derived hydrologic environmental gradients, and forest canopy characteristics with important cascading effects on ecosystem function and biosphere-atmosphere interactions. In 2011, the Carnegie Airborne Observatory (CAO) Airborne Taxonomic Mapping System (AToMS) was used to map a large section of the Los Amigos Conservation Concession harboring largely intact lowland humid tropical forest in the southwestern Peruvian Amazon. The CAO Visible-Shortwave Imaging Spectrometer (VSWIR) collected 480-band high-fidelity imaging spectroscopy data of the forest canopy, while its high-resolution dual waveform LiDAR captured information on canopy structure and the underlying terrain. The data were used to quantify relationships between topographic and hydrologic gradients and forest functional traits. Results suggest strong local hydrogeomorphic control over vegetation spectral properties with known relationships to canopy functional traits, including pigment and nutrient concentrations and light capture, as well as canopy structural characteristics, including vegetation height, understory plant cover, and aboveground biomass. Data from CAO-AToMS reveals local-scale patterns in environmental conditions and ecological variation that meets or exceeds the variation previously reported across ecosystems of the Western Amazon Basin.

Wallops' Low Elevation Link Analysis for the Constellation Launch/Ascent Links

Science.gov (United States)

Cheung, Kar-Ming; Ho, Christian; Kantak, Anil; Lee, Charles; Tye, Robert; Richards, Edger; Sham, Catherine; Schlesinger, Adam; Barritt, Brian

2011-01-01

Prior to the redirection of the Constellation Program, the Wallops 11.3-meter ground station was tasked to support the Orion's Dissimilar Voice (DV) link and the Ares's Development Flight Instrument (DFI) link. Detailed analysis of the launch trajectories indicates that during the launch and ascent operation, the critical events of Orion-Ares main engine cut off (MECO) and Separation occur at low elevation angle. We worked with engineers from both Wallops Flight Facility (WFF) and Johnson Space Center (JSC) to perform an intensive measurement and link analysis campaign on the DV and DFI links. The main results were as follows: (1) The DV links have more than 3 dB margin at MECO and Separation. (2) The DFI links have 0 dB margin at Separation during certain weather condition in summer season. (3) Tropospheric scintillation loss is the major impairment at low elevation angle. (4) The current scintillation models in the Recommendation ITU-R P.618 (Propagation data and prediction methods required for the design of Earth-space telecommunication systems), which are based on limited experimental and theoretical work, exhibit idiosyncratic behaviors. We developed an improved model based on the measurements of recent Shuttle mission launch and ascent links and the ITU propagation data. (5) Due to the attitude uncertainty of the Orion-Ares stack, the high dynamics of the launch and ascent trajectory, and the irregularity of the Orion and Ares antenna patterns, we employed new link analysis approach to model the spacecraft antenna gain. In this paper we discuss the details of the aforementioned results.

Aerial radiometric and magnetic survey: Evansville National Topographic Map, Indiana and Kentucky, southeast US Project

International Nuclear Information System (INIS)

1980-01-01

The results of analyses of the airborne gamma radiation and total magnetic field survey flown for the region identified as the Evansville National Topographic Map NJ16-8 are presented. The airborne data gathered are reduced by ground computer facilities to yield profile plots of the basic uranium, thorium and potassium equivalent gamma radiation intensities, ratios of these intensities, aircraft altitude above the earth's surface, total gamma ray and earth's magnetic field intensity, correlated as a function of geologic units. The distribution of data within each geologic unit, for all surveyed map lines and tie lines, has been calculated and is included. Two sets of profiled data for each line are included, with one set displaying the above-cited data. The second set includes only flight line magnetic field, temperature, pressure, altitude data plus magnetic field data as measured at a base station. A general description of the area, including descriptions of the various geologic units and the corresponding airborne data, is included also

2008 US Army Corps of Engineers (USACE) Joint Airborne Lidar Bathymetry Technical Center of Expertise (JALBTCX) Topobathy Lidar: North Carolina

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — These files contain topographic lidar data collected by the Compact Hydrographic Airborne Rapid Total Survey (CHARTS) system along the coast of North Carolina near...

Aerial radiometric and magnetic survey: St. Louis national topographic map, Illinois/Missouri. Final report

International Nuclear Information System (INIS)

1981-01-01

The results of analyses of the airborne gamma radiation and total magnetic field survey flown for the region identified as the St. Louis National Topographic Map NJ15-6 is presented in this report. The airborne data gathered is reduced by ground computer facilities to yield profile plots of the basic uranium, thorium and potassium equivalent gamma radiation intensities, ratios of these intensities, aircraft altitude above the earth's surface, total gamma ray and earth's magnetic field intensity, correlated as a function of geologic units. The distribution of data within each geologic unit, for all surveying map lines and tie lines, has been calculated and is included. Two sets of profiled data for each line are included, with one set displaying the above-cited data. The second set includes only flight line magnetic field, temperature, pressure, altitude data plus magnetic field data as measured at a base station. A general description of the area, including descriptions of the various geologic units and the corresponding airborne data, is included also

Aerial radiometric and magnetic survey: McIntosh National Topographic Map, North Dakota/South Dakota. Final report

International Nuclear Information System (INIS)

1981-01-01

The results of analyses of the airborne gamma radiation and total magnetic field survey flown for the region identified as the McIntosh National Topographic Map NL14-7 are presented. The airborne data gathered are reduced by ground computer facilities to yield profile plots of the basic uranium, thorium and potassium equivalent gamma radiation intensities, ratios of these intensities, aircraft altitude above the earth's surface, total gamma ray and earth's magnetic field intensity, correlated as a function of geologic units. The distribution of data within each geologic unit, for all surveyed map lines and tie lines, has been calculated and is included. Two sets of profiled data for each line are included, with one set displaying the above-cited data. The second set includes only flight line magnetic field, temperature, pressure, altitude data plus magnetic field data as measured at a base station. A general description of the area, including descriptions of the various geologic units and the corresponding airborne data, is included also

Aerial radiometric and magnetic survey, San Angelo National Topographic Map: Texas, West Texas Project. Final report

International Nuclear Information System (INIS)

1980-05-01

The results of analyses of the airborne gamma radiation and total magnetic field survey flown for the region identified as the San Angelo National Topographic Map NH14-1 are presented. The airborne data gathered are reduced by ground computer facilities to yield profile plots of the basic uranium, thorium, and potassium equivalent gamma radiation intensities, ratios of these intensities, aircraft altitude above the earth's surface, total gamma ray and earth's magnetic field intensity, correlated as a function of geologic units. The distribution of data within each geologic unit, for all surveyed map lines and tie lines, has been calculated and is included. Two sets of profiled data for each line are included, with one set displaying the above-cited data. The second set includes only flight line magnetic field, temperature, pressure, altitude data plus magnetic field data as measured at a base station. A general description of the area, including descriptions of the various geologic units and the corresponding airborne data, is included

Prediction of topographic and bathymetric measurement performance of airborne low-SNR lidar systems

Science.gov (United States)

Cossio, Tristan

Low signal-to-noise ratio (LSNR) lidar (light detection and ranging) is an alternative paradigm to traditional lidar based on the detection of return signals at the single photoelectron level. The objective of this work was to predict low altitude (600 m) LSNR lidar system performance with regards to elevation measurement and target detection capability in topographic (dry land) and bathymetric (shallow water) scenarios. A modular numerical sensor model has been developed to provide data for further analysis due to the dearth of operational low altitude LSNR lidar systems. This simulator tool is described in detail, with consideration given to atmospheric effects, surface conditions, and the effects of laser phenomenology. Measurement performance analysis of the simulated topographic data showed results comparable to commercially available lidar systems, with a standard deviation of less than 12 cm for calculated elevation values. Bathymetric results, although dependent largely on water turbidity, were indicative of meter-scale horizontal data spacing for sea depths less than 5 m. The high prevalence of noise in LSNR lidar data introduces significant difficulties in data analysis. Novel algorithms to reduce noise are described, with particular focus on their integration into an end-to-end target detection classifier for both dry and submerged targets (cube blocks, 0.5 m to 1.0 m on a side). The key characteristic exploited to discriminate signal and noise is the temporal coherence of signal events versus the random distribution of noise events. Target detection performance over dry earth was observed to be robust, reliably detecting over 90% of targets with a minimal false alarm rate. Comparable results were observed in waters of high clarity, where the investigated system was generally able to detect more than 70% of targets to a depth of 5 m. The results of the study show that CATS, the University of Florida's LSNR lidar prototype, is capable of high fidelity

ANALYSIS OF RADAR AND OPTICAL SPACE BORNE DATA FOR LARGE SCALE TOPOGRAPHICAL MAPPING

Directory of Open Access Journals (Sweden)

W. Tampubolon

2015-03-01

Full Text Available Normally, in order to provide high resolution 3 Dimension (3D geospatial data, large scale topographical mapping needs input from conventional airborne campaigns which are in Indonesia bureaucratically complicated especially during legal administration procedures i.e. security clearance from military/defense ministry. This often causes additional time delays besides technical constraints such as weather and limited aircraft availability for airborne campaigns. Of course the geospatial data quality is an important issue for many applications. The increasing demand of geospatial data nowadays consequently requires high resolution datasets as well as a sufficient level of accuracy. Therefore an integration of different technologies is required in many cases to gain the expected result especially in the context of disaster preparedness and emergency response. Another important issue in this context is the fast delivery of relevant data which is expressed by the term “Rapid Mapping”. In this paper we present first results of an on-going research to integrate different data sources like space borne radar and optical platforms. Initially the orthorectification of Very High Resolution Satellite (VHRS imagery i.e. SPOT-6 has been done as a continuous process to the DEM generation using TerraSAR-X/TanDEM-X data. The role of Ground Control Points (GCPs from GNSS surveys is mandatory in order to fulfil geometrical accuracy. In addition, this research aims on providing suitable processing algorithm of space borne data for large scale topographical mapping as described in section 3.2. Recently, radar space borne data has been used for the medium scale topographical mapping e.g. for 1:50.000 map scale in Indonesian territories. The goal of this on-going research is to increase the accuracy of remote sensing data by different activities, e.g. the integration of different data sources (optical and radar or the usage of the GCPs in both, the optical and the

EXTRACTION OF BUILDING BOUNDARY LINES FROM AIRBORNE LIDAR POINT CLOUDS

Directory of Open Access Journals (Sweden)

Y.-H. Tseng

2016-10-01

Full Text Available Building boundary lines are important spatial features that characterize the topographic maps and three-dimensional (3D city models. Airborne LiDAR Point clouds provide adequate 3D spatial information for building boundary mapping. However, information of boundary features contained in point clouds is implicit. This study focuses on developing an automatic algorithm of building boundary line extraction from airborne LiDAR data. In an airborne LiDAR dataset, top surfaces of buildings, such as roofs, tend to have densely distributed points, but vertical surfaces, such as walls, usually have sparsely distributed points or even no points. The intersection lines of roof and wall planes are, therefore, not clearly defined in point clouds. This paper proposes a novel method to extract those boundary lines of building edges. The extracted line features can be used as fundamental data to generate topographic maps of 3D city model for an urban area. The proposed method includes two major process steps. The first step is to extract building boundary points from point clouds. Then the second step is followed to form building boundary line features based on the extracted boundary points. In this step, a line fitting algorithm is developed to improve the edge extraction from LiDAR data. Eight test objects, including 4 simple low buildings and 4 complicated tall buildings, were selected from the buildings in NCKU campus. The test results demonstrate the feasibility of the proposed method in extracting complicate building boundary lines. Some results which are not as good as expected suggest the need of further improvement of the method.

Topographic mapping

Science.gov (United States)

,

2008-01-01

The U.S. Geological Survey (USGS) produced its first topographic map in 1879, the same year it was established. Today, more than 100 years and millions of map copies later, topographic mapping is still a central activity for the USGS. The topographic map remains an indispensable tool for government, science, industry, and leisure. Much has changed since early topographers traveled the unsettled West and carefully plotted the first USGS maps by hand. Advances in survey techniques, instrumentation, and design and printing technologies, as well as the use of aerial photography and satellite data, have dramatically improved mapping coverage, accuracy, and efficiency. Yet cartography, the art and science of mapping, may never before have undergone change more profound than today.

Mapping Above- and Below-Ground Carbon Pools in Boreal Forests: The Case for Airborne Lidar.

Science.gov (United States)

Kristensen, Terje; Næsset, Erik; Ohlson, Mikael; Bolstad, Paul V; Kolka, Randall

2015-01-01

A large and growing body of evidence has demonstrated that airborne scanning light detection and ranging (lidar) systems can be an effective tool in measuring and monitoring above-ground forest tree biomass. However, the potential of lidar as an all-round tool for assisting in assessment of carbon (C) stocks in soil and non-tree vegetation components of the forest ecosystem has been given much less attention. Here we combine the use airborne small footprint scanning lidar with fine-scale spatial C data relating to vegetation and the soil surface to describe and contrast the size and spatial distribution of C pools within and among multilayered Norway spruce (Picea abies) stands. Predictor variables from lidar derived metrics delivered precise models of above- and below-ground tree C, which comprised the largest C pool in our study stands. We also found evidence that lidar canopy data correlated well with the variation in field layer C stock, consisting mainly of ericaceous dwarf shrubs and herbaceous plants. However, lidar metrics derived directly from understory echoes did not yield significant models. Furthermore, our results indicate that the variation in both the mosses and soil organic layer C stock plots appears less influenced by differences in stand structure properties than topographical gradients. By using topographical models from lidar ground returns we were able to establish a strong correlation between lidar data and the organic layer C stock at a stand level. Increasing the topographical resolution from plot averages (~2000 m2) towards individual grid cells (1 m2) did not yield consistent models. Our study demonstrates a connection between the size and distribution of different forest C pools and models derived from airborne lidar data, providing a foundation for future research concerning the use of lidar for assessing and monitoring boreal forest C.

On the Atmospheric Correction of Antarctic Airborne Hyperspectral Data

Directory of Open Access Journals (Sweden)

Martin Black

2014-05-01

Full Text Available The first airborne hyperspectral campaign in the Antarctic Peninsula region was carried out by the British Antarctic Survey and partners in February 2011. This paper presents an insight into the applicability of currently available radiative transfer modelling and atmospheric correction techniques for processing airborne hyperspectral data in this unique coastal Antarctic environment. Results from the Atmospheric and Topographic Correction version 4 (ATCOR-4 package reveal absolute reflectance values somewhat in line with laboratory measured spectra, with Root Mean Square Error (RMSE values of 5% in the visible near infrared (0.4–1 µm and 8% in the shortwave infrared (1–2.5 µm. Residual noise remains present due to the absorption by atmospheric gases and aerosols, but certain parts of the spectrum match laboratory measured features very well. This study demonstrates that commercially available packages for carrying out atmospheric correction are capable of correcting airborne hyperspectral data in the challenging environment present in Antarctica. However, it is anticipated that future results from atmospheric correction could be improved by measuring in situ atmospheric data to generate atmospheric profiles and aerosol models, or with the use of multiple ground targets for calibration and validation.

Airborne laser altimeter measurements of landscape topography

International Nuclear Information System (INIS)

Ritchie, J.C.

1995-01-01

Measurements of topography can provide a wealth of information on landscape properties for managing hydrologic and geologic systems and conserving natural and agricultural resources. This article discusses the application of an airborne laser altimeter to measure topography and other landscape surface properties. The airborne laser altimeter makes 4000 measurements per second with a vertical recording resolution of 5 cm. Data are collected digitally with a personal computer. A video camera, borehole sighted with the laser, records an image for locating flight lines. GPS data are used to locate flight line positions on the landscape. Laser data were used to measure vegetation canopy topography, height, cover, and distribution and to measure microtopography of the land surface and gullies with depths of 15–20 cm. Macrotopography of landscape profiles for segments up to 4 km were in agreement with available topographic maps but provided more detail. Larger gullies with and without vegetation, and stream channel cross sections and their associated floodplains have also been measured and reported in other publications. Landscape segments for any length could be measured for either micro- or macrotopography. Airborne laser altimeter measurements of landscape profiles can provide detailed information on landscape properties or specific needs that will allow better decisions on the design and location of structures (i.e., roads, pipe, and power lines) and for improving the management and conservation of natural and agricultural landscapes. (author)

ICESat-2 simulated data from airborne altimetery

Science.gov (United States)

Brunt, K. M.; Neumann, T.; Markus, T.; Brenner, A. C.; Barbieri, K.; Field, C.; Sirota, M.

2010-12-01

Ice, Cloud, and land Elevation Satellite-2 (ICESat-2) is scheduled to launch in 2015 and will carry onboard the Advanced Topographic Laser Altimeter System (ATLAS), which represents a new approach to spaceborne determination of surface elevations. Specifically, the current ATLAS design is for a micropulse, multibeam, photon-counting laser altimeter with lower energy, a shorter pulse width, and a higher repetition rate relative to the Geoscience Laser Altimeter (GLAS), the instrument that was onboard ICESat. Given the new and untested technology associated with ATLAS, airborne altimetry data is necessary (1) to test the proposed ATLAS instrument geometry, (2) to validate instrument models, and (3) to assess the atmospheric effects on multibeam altimeters. We present an overview of the airborne instruments and datasets intended to address the ATLAS instrument concept, including data collected over Greenland (July 2009) using an airborne SBIR prototype 100 channel, photon-counting, terrain mapping altimeter, which addresses the first of these 3 scientific concerns. Additionally, we present the plan for further simulator data collection over vegetated and ice covered regions using Multiple Altimeter Beam Experimental Lidar (MABEL), intended to address the latter two scientific concerns. As the ICESAT-2 project is in the design phase, the particular configuration of the ATLAS instrument may change. However, we expect this work to be relevant as long as ATLAS pursues a photon-counting approach.

Forsmark site investigation. Interpretation of topographic lineaments 2002

International Nuclear Information System (INIS)

Isaksson, Hans

2003-04-01

SKB performs site investigations for localization of a deep repository for high level radioactive waste. The site investigations are performed in two municipalities; Oesthammar and Oskarshamn. The Forsmark investigation area is situated in Oesthammar, close to the Forsmark nuclear power plant. The purpose of interpretation of lineaments from topographic data is to identify linear features (lineaments), which may correspond to deformation zones in the bedrock. The data will be combined with interpretations of lineaments from airborne geophysical data in order to produce an integrated lineament interpretation for the Forsmark area. This integrated interpretation will be combined with geological data in order to establish a bedrock geological map of the Forsmark area. The area for the lineament interpretation is the same as that selected for the bedrock mapping activities during 2002, i.e. the land area around Forsmark

Assessment of NASA airborne laser altimetry data using ground-based GPS data near Summit Station, Greenland

Science.gov (United States)

Brunt, Kelly M.; Hawley, Robert L.; Lutz, Eric R.; Studinger, Michael; Sonntag, John G.; Hofton, Michelle A.; Andrews, Lauren C.; Neumann, Thomas A.

2017-03-01

A series of NASA airborne lidars have been used in support of satellite laser altimetry missions. These airborne laser altimeters have been deployed for satellite instrument development, for spaceborne data validation, and to bridge the data gap between satellite missions. We used data from ground-based Global Positioning System (GPS) surveys of an 11 km long track near Summit Station, Greenland, to assess the surface-elevation bias and measurement precision of three airborne laser altimeters including the Airborne Topographic Mapper (ATM), the Land, Vegetation, and Ice Sensor (LVIS), and the Multiple Altimeter Beam Experimental Lidar (MABEL). Ground-based GPS data from the monthly ground-based traverses, which commenced in 2006, allowed for the assessment of nine airborne lidar surveys associated with ATM and LVIS between 2007 and 2016. Surface-elevation biases for these altimeters - over the flat, ice-sheet interior - are less than 0.12 m, while assessments of measurement precision are 0.09 m or better. Ground-based GPS positions determined both with and without differential post-processing techniques provided internally consistent solutions. Results from the analyses of ground-based and airborne data provide validation strategy guidance for the Ice, Cloud, and land Elevation Satellite 2 (ICESat-2) elevation and elevation-change data products.

Historical Topographic Map Collection bookmark

Science.gov (United States)

Fishburn, Kristin A.; Allord, Gregory J.

2017-06-29

The U.S. Geological Survey (USGS) National Geospatial Program is scanning published USGS 1:250,000-scale and larger topographic maps printed between 1884, the inception of the topographic mapping program, and 2006. The goal of this project, which began publishing the historical scanned maps in 2011, is to provide a digital repository of USGS topographic maps, available to the public at no cost. For more than 125 years, USGS topographic maps have accurately portrayed the complex geography of the Nation. The USGS is the Nation’s largest producer of printed topographic maps, and prior to 2006, USGS topographic maps were created using traditional cartographic methods and printed using a lithographic printing process. As the USGS continues the release of a new generation of topographic maps (US Topo) in electronic form, the topographic map remains an indispensable tool for government, science, industry, land management planning, and leisure.

The alpine Swiss-French airborne gravity survey

Science.gov (United States)

Verdun, Jérôme; Klingelé, Emile E.; Bayer, Roger; Cocard, Marc; Geiger, Alain; Kahle, Hans-Gert

2003-01-01

ground topographic corrections over the highest mountains, results in significantly reducing the differences between airborne and ground upward-continued Bouguer anomalies, which shows that some of the misfit stems from errors in the ground data.

Integrating bathymetric and topographic data

Science.gov (United States)

Teh, Su Yean; Koh, Hock Lye; Lim, Yong Hui; Tan, Wai Kiat

2017-11-01

The quality of bathymetric and topographic resolution significantly affect the accuracy of tsunami run-up and inundation simulation. However, high resolution gridded bathymetric and topographic data sets for Malaysia are not freely available online. It is desirable to have seamless integration of high resolution bathymetric and topographic data. The bathymetric data available from the National Hydrographic Centre (NHC) of the Royal Malaysian Navy are in scattered form; while the topographic data from the Department of Survey and Mapping Malaysia (JUPEM) are given in regularly spaced grid systems. Hence, interpolation is required to integrate the bathymetric and topographic data into regularly-spaced grid systems for tsunami simulation. The objective of this research is to analyze the most suitable interpolation methods for integrating bathymetric and topographic data with minimal errors. We analyze four commonly used interpolation methods for generating gridded topographic and bathymetric surfaces, namely (i) Kriging, (ii) Multiquadric (MQ), (iii) Thin Plate Spline (TPS) and (iv) Inverse Distance to Power (IDP). Based upon the bathymetric and topographic data for the southern part of Penang Island, our study concluded, via qualitative visual comparison and Root Mean Square Error (RMSE) assessment, that the Kriging interpolation method produces an interpolated bathymetric and topographic surface that best approximate the admiralty nautical chart of south Penang Island.

Wallops Low Elevation Link Analysis for the Constellation Launch/Ascent Links

Science.gov (United States)

Cheung, Keith; Ho, C.; Kantak, A.; Lee, C.; Tye, R.; Richards, E.; Sham, C.; Schlesinger, A.; Barritt, B.

2011-01-01

To execute the President's Vision for Space Exploration, the Constellation Program (CxP) was formed to build the next generation spacecraft Orion and launch vehicles Ares, to transport human and cargo to International Space Station (ISS), moon, and Mars. This paper focuses on the detailed link analysis for Orion/Ares s launch and ascent links with Wallops 11.3m antenna (1) Orion's Dissimilar Voice link: 10.24 Kbps, 2-way (2) Ares Developmental Flight Instrument link, 20 Mbps, downlink. Three launch trajectories are considered: TD7-E, F (Feb), and G (Aug). In certain launch scenarios, the critical events of main engine cutoff (MECO) and Separation occur during the low elevation regime of WFF s downrange -- less than 5 degree elevation angle. The goal of the study is to access if there is enough link margins for WFF to track the DV and DFI links.

Topographic laser ranging and scanning principles and processing

CERN Document Server

Shan, Jie

2008-01-01

A systematic, in-depth introduction to theories and principles of Light Detection and Ranging (LiDAR) technology is long overdue, as it is the most important geospatial data acquisition technology to be introduced in recent years. An advanced discussion, this text fills the void.Professionals in fields ranging from geology, geography and geoinformatics to physics, transportation, and law enforcement will benefit from this comprehensive discussion of topographic LiDAR principles, systems, data acquisition, and data processing techniques. The book covers ranging and scanning fundamentals, and broad, contemporary analysis of airborne LiDAR systems, as well as those situated on land and in space. The authors present data collection at the signal level in terms of waveforms and their properties; at the system level with regard to calibration and georeferencing; and at the data level to discuss error budget, quality control, and data organization. They devote the bulk of the book to LiDAR data processing and inform...

Spatiotemporal Variability in Topographic and Vegetative Controls on Basin-Wide Snow Distribution in the Tuolumne River Basin

Science.gov (United States)

Bolliger, I. W.; Molotch, N. P.

2017-12-01

An accurate empirical characterization of topographic and vegetative controls on snow distribution can lead to a greater understanding of the underlying physical processes and an increased ability to downscale lower-resolution observations. As improved water resource forecast methods are sought to address climate-driven nonstationarity in snow distributions, constraining our uncertainty in topographic and vegetative controls on these distributions becomes imperative. The Airborne Snow Observatory (ASO) LiDAR-based observation campaign provides a novel dataset with the necessary spatiotemporal extent and resolution for rigorous assessment of spatiotemporal variance in topographic and vegetative controls. In this study, we examine ASO measurements from 2013-2016 in the Tuolumne River Basin, exploring relationships to topographic and vegetation features derived from analogous snow-free LiDAR flights. To address nonlinearities in these relationships, we use single and ensemble regression tree approaches and assess metrics of feature importance, while for greater interpretability, we assess parameter values from multiple linear regression. These complementary analyses are performed for each flight date in 2013-2016 at resolutions between 3 and 500m. They are performed globally and for each of the 13 HUC12-level watersheds within the study area. Feature importance and parameter values are compared across features and across intra-seasonal, inter-seasonal, spatial, and model scale dimensions. Initial results demonstrate a consistent pattern to the changing influence of topographic and vegetative features over intra-annual timescales. They support previous findings that elevational gradients dominate local topographic and vegetative features in controlling both depth and SWE yet suggest a declining importance of elevation in the ablation period. Together, topographic and vegetative features explain more of the spatial distribution of depth and SWE observed during

Topographic Effects in Geoid Determinations

Directory of Open Access Journals (Sweden)

Lars E. Sjöberg

2018-04-01

Full Text Available Traditionally, geoid determination is applied by Stokes’ formula with gravity anomalies after removal of the attraction of the topography by a simple or refined Bouguer correction, and restoration of topography by the primary indirect topographic effect (PITE after integration. This technique leads to an error of the order of the quasigeoid-to-geoid separation, which is mainly due to an incomplete downward continuation of gravity from the surface to the geoid. Alternatively, one may start from the modern surface gravity anomaly and apply the direct topographic effect on the anomaly, yielding the no-topography gravity anomaly. After downward continuation of this anomaly to sea-level and Stokes integration, a theoretically correct geoid height is obtained after the restoration of the topography by the PITE. The difference between the Bouguer and no-topography gravity anomalies (on the geoid or in space is the “secondary indirect topographic effect”, which is a necessary correction in removing all topographic signals. In modern applications of an Earth gravitational model (EGM in geoid determination a topographic correction is also needed in continental regions. Without the correction the error can range to a few metres in the highest mountains. The remove-compute-restore and Royal Institute of Technology (KTH techniques for geoid determinations usually employ a combination of Stokes’ formula and an EGM. Both techniques require direct and indirect topographic corrections, but in the latter method these corrections are merged as a combined topographic effect on the geoid height. Finally, we consider that any uncertainty in the topographic density distribution leads to the same error in gravimetric and geometric geoid estimates, deteriorating GNSS-levelling as a tool for validating the topographic mass distribution correction in a gravimetric geoid model.

Research on airborne comprehensive survey system of atmosphere quality

International Nuclear Information System (INIS)

Yu Zhentao; Yu Yanbin

1998-01-01

The global atmosphere pollution is becoming more and more serious, affecting the human existence and development. Besides, the high spectrum resolution remote sensing technique, which has been applied to observe topographic features, identify military objectives and distinguish lithology and vegetation, has the relation to atmosphere quality and is influenced by atmosphere pollution (including radon pollution) and dust content in the atmosphere, it is imperative to monitor atmosphere quality. Based upon the selection of some main parameters evaluating atmospheric quality and necessary equipment, the author introduces the design of multiple airborne comprehensive survey system of atmosphere quality and how to deal with problems that crop up during the hardware designing and software programming

UAS-Borne Photogrammetry for Surface Topographic Characterization: A Ground-Truth Baseline for Future Change Detection and Refinement of Scaled Remotely-Sensed Datasets

Science.gov (United States)

Coppersmith, R.; Schultz-Fellenz, E. S.; Sussman, A. J.; Vigil, S.; Dzur, R.; Norskog, K.; Kelley, R.; Miller, L.

2015-12-01

While long-term objectives of monitoring and verification regimes include remote characterization and discrimination of surficial geologic and topographic features at sites of interest, ground truth data is required to advance development of remote sensing techniques. Increasingly, it is desirable for these ground-based or ground-proximal characterization methodologies to be as nimble, efficient, non-invasive, and non-destructive as their higher-altitude airborne counterparts while ideally providing superior resolution. For this study, the area of interest is an alluvial site at the Nevada National Security Site intended for use in the Source Physics Experiment's (Snelson et al., 2013) second phase. Ground-truth surface topographic characterization was performed using a DJI Inspire 1 unmanned aerial system (UAS), at very low altitude (clouds. Within the area of interest, careful installation of surveyed ground control fiducial markers supplied necessary targets for field collection, and information for model georectification. The resulting model includes a Digital Elevation Model derived from 2D imagery. It is anticipated that this flexible and versatile characterization process will provide point cloud data resolution equivalent to a purely ground-based LiDAR scanning deployment (e.g., 1-2cm horizontal and vertical resolution; e.g., Sussman et al., 2012; Schultz-Fellenz et al., 2013). In addition to drastically increasing time efficiency in the field, the UAS method also allows for more complete coverage of the study area when compared to ground-based LiDAR. Comparison and integration of these data with conventionally-acquired airborne LiDAR data from a higher-altitude (~ 450m) platform will aid significantly in the refinement of technologies and detection capabilities of remote optical systems to identify and detect surface geologic and topographic signatures of interest. This work includes a preliminary comparison of surface signatures detected from varying

Delineation of peatland lagg boundaries from airborne LiDAR

Science.gov (United States)

Langlois, Melanie N.; Richardson, Murray C.; Price, Jonathan S.

2017-09-01

In Canada, peatlands are the most common type of wetland, but boundary delineation in peatland complexes has received little attention in the scientific literature. Typically, peatland boundaries are mapped as crisp, absolute features, and the transitional lagg zone—the ecotone found between a raised bog and the surrounding mineral land—is often overlooked. In this study, we aim (1) to advance existing approaches for detecting and locating laggs and lagg boundaries using airborne LiDAR surveys and (2) to describe the spatial distribution of laggs around raised bog peatlands. Two contrasting spatial analytical approaches for lagg detection were tested using five LiDAR-derived topographic and vegetation indices: topography, vegetation height, topographic wetness index, the standard deviation of the vegetation's height (as a proxy for the complexity of the vegetation's structure), and local indices of elevation variance. Using a dissimilarity approach (edge-detection, split-moving window analysis), no one variable accurately depicted both the lagg-mineral land and bog-lagg boundaries. Some indicators were better at predicting the bog-lagg boundary (i.e., vegetation height) and others at finding the lagg-mineral land boundary (i.e., topography). Dissimilarity analysis reinforces the usefulness of derived variables (e.g., wetness indices) in locating laggs, especially for those with weak topographic and vegetation gradients. When the lagg was confined between the bog and the adjacent upland, it took a linear form, parallel to the peatland's edge and was easier to predict. When the adjacent mineral land was flat or sloping away from the peatland, the lagg was discontinuous and intermittent and more difficult to predict.

Regional-scale airborne electromagnetic surveying of the Yucatan karst aquifer (Mexico): geological and hydrogeological interpretation

DEFF Research Database (Denmark)

Gondwe, Bibi Ruth Neuman; Ottowitz, David; Supper, Robert

2012-01-01

-spectral remote sensing imagery, shuttle radar topography data and frequency-domain airborne electromagnetic (AEM) survey data were used to map karst-aquifer structure on the Yucatan Peninsula, Mexico. Anomalous AEM responses correlated with topographic features and anomalous spectral reflectance of the terrain...... as ejecta from the Chicxulub impact (Cretaceous/Paleogene boundary), based on similar resistivity signatures found in borehole logs. Due to limited sensitivity of the AEM survey, the subsurface configuration beneath the low-resistivity layer could not be unambiguously determined. AEM measurements combined...

Topographic processing in developmental prosopagnosia

DEFF Research Database (Denmark)

Klargaard, Solja K.; Starrfelt, Randi; Petersen, Anders

2016-01-01

deficit in visual processing or visual short-term memory. Interestingly, a classical dissociation could be demonstrated between impaired face memory and preserved topographic memory in two developmental prosopagnosics. We conclude that impairments in topographic memory tend to co-occur with developmental......Anecdotal evidence suggests a relation between impaired spatial (navigational) processing and developmental prosopagnosia. To address this formally, we tested two aspects of topographic processing – that is, perception and memory of mountain landscapes shown from different viewpoints. Participants...

Topographical ability in Developmental Prosopagnosia

DEFF Research Database (Denmark)

Klargaard, Solja; Starrfelt, Randi; Petersen, Anders

2016-01-01

and topographical short-term memory (2 sec delay). The stimulus material consisted of computer-generated mountain landscapes shown from seven different viewpoints. In comparison with controls, the individuals with DP had no difficulty in perceiving the spatial aspects of the landscapes, but some were impaired...... in the short-term retention of these mountain landscapes. No systematic relationship (correlation) was found between recognition memory for faces and landscapes. Indeed, three cases with DP showed a statistically significant classical dissociation between these domains. Additional testing revealed...... that the deficit in topographical memory did not relate systematically to impaired visual short-term memory or recognition of more complex material. In conclusion, some individuals with DP show subtle deficits in topographical memory. Importantly, the deficits in topographical memory and face recognition do...

UAV photogrammetry for topographic monitoring of coastal areas

Science.gov (United States)

Gonçalves, J. A.; Henriques, R.

2015-06-01

Coastal areas suffer degradation due to the action of the sea and other natural and human-induced causes. Topographical changes in beaches and sand dunes need to be assessed, both after severe events and on a regular basis, to build models that can predict the evolution of these natural environments. This is an important application for airborne LIDAR, and conventional photogrammetry is also being used for regular monitoring programs of sensitive coastal areas. This paper analyses the use of unmanned aerial vehicles (UAV) to map and monitor sand dunes and beaches. A very light plane (SwingletCam) equipped with a very cheap, non-metric camera was used to acquire images with ground resolutions better than 5 cm. The Agisoft Photoscan software was used to orientate the images, extract point clouds, build a digital surface model and produce orthoimage mosaics. The processing, which includes automatic aerial triangulation with camera calibration and subsequent model generation, was mostly automated. To achieve the best positional accuracy for the whole process, signalised ground control points were surveyed with a differential GPS receiver. Two very sensitive test areas on the Portuguese northwest coast were analysed. Detailed DSMs were obtained with 10 cm grid spacing and vertical accuracy (RMS) ranging from 3.5 to 5.0 cm, which is very similar to the image ground resolution (3.2-4.5 cm). Where possible to assess, the planimetric accuracy of the orthoimage mosaics was found to be subpixel. Within the regular coastal monitoring programme being carried out in the region, UAVs can replace many of the conventional flights, with considerable gains in the cost of the data acquisition and without any loss in the quality of topographic and aerial imagery data.

Corneal topographer based on the Hartmann test.

Science.gov (United States)

Mejía, Yobani; Galeano, Janneth C

2009-04-01

The purpose of this article is to show the performance of a topographer based on the Hartmann test for convex surfaces of F/# approximately 1. This topographer, called "Hartmann Test topographer (HT topographer)," is a prototype developed in the Physics Department of the Universidad Nacional de Colombia. From the Hartmann pattern generated by the surface under test, and by the Fourier analysis and the optical aberration theory we obtain the sagitta (elevation map) of the surface. Then, taking the first and the second derivatives of the sagitta in the radial direction we obtain the meridional curvature map. The method is illustrated with an example. To check the performance of the HT topographer a toric surface, a revolution aspherical surface, and two human corneas were measured. Our results are compared with those obtained with a Placido ring topographer (Tomey TMS-4 videokeratoscope), and we show that our curvature maps are similar to those obtained with the Placido ring topographer. The HT topographer is able to reconstruct the corneal topography potentially eradicating the skew ray problem, therefore, corneal defects can be visualized more. The results are presented by elevation and meridional curvature maps.

A topographic feature taxonomy for a U.S. national topographic mapping ontology

Science.gov (United States)

Varanka, Dalia E.

2013-01-01

Using legacy feature lists from the U.S. National Topographic Mapping Program of the twentieth century, a taxonomy of features is presented for purposes of developing a national topographic feature ontology for geographic mapping and analysis. After reviewing published taxonomic classifications, six basic classes are suggested; terrain, surface water, ecological regimes, built-up areas, divisions, and events. Aspects of ontology development are suggested as the taxonomy is described.

Unveiling topographical changes using LiDAR mapping capability: case study of Belaga in Sarawak, East-Malaysia

Science.gov (United States)

Ganendra, T. R.; Khan, N. M.; Razak, W. J.; Kouame, Y.; Mobarakeh, E. T.

2016-06-01

The use of Light Detection and Ranging (LiDAR) remote sensing technology to scan and map landscapes has proven to be one of the most popular techniques to accurately map topography. Thus, LiDAR technology is the ultimate method of unveiling the surface feature under dense vegetation, and, this paper intends to emphasize the diverse techniques that can be utilized to elucidate topographical changes over the study area, using multi-temporal airborne full waveform LiDAR datasets collected in 2012 and 2014. Full waveform LiDAR data offers access to an almost unlimited number of returns per shot, which enables the user to explore in detail topographical changes, such as vegetation growth measurement. The study also found out topography changes at the study area due to earthwork activities contributing to soil consolidation, soil erosion and runoff, requiring cautious monitoring. The implications of this study not only concurs with numerous investigations undertaken by prominent researchers to improve decision making, but also corroborates once again that investigations employing multi-temporal LiDAR data to unveil topography changes in vegetated terrains, produce more detailed and accurate results than most other remote sensing data.

Ontology-based integration of topographic data sets

NARCIS (Netherlands)

Uitermark, HT; van Oosterom, PJM; Mars, NJI; Molenaar, M

The integration of topographic data sets is defined as the process of establishing relationships between corresponding object instances in different, autonomously produced, topographic data sets of the same geographic space. The problem of integrating topographic data sets is in finding these

Topographic Steering of Enhanced Ice Flow at the Bottleneck Between East and West Antarctica

DEFF Research Database (Denmark)

Winter, Kate; Ross, Neil; Ferraccioli, Fausto

2018-01-01

Hypothesized drawdown of the East Antarctic Ice Sheet through the “bottleneck” zone between East and West Antarctica would have significant impacts for a large proportion of the Antarctic Ice Sheet. Earth observation satellite orbits and a sparseness of radio echo sounding data have restricted...... investigations of basal boundary controls on ice flow in this region until now. New airborne radio echo sounding surveys reveal complex topography of high relief beneath the southernmost Weddell/Ross ice divide, with three subglacial troughs connecting interior Antarctica to the Foundation and Patuxent Ice...... Streams and Siple Coast ice streams. These troughs route enhanced ice flow through the interior of Antarctica but limit potential drawdown of the East Antarctic Ice Sheet through the bottleneck zone. In a thinning or retreating scenario, these topographically controlled corridors of enhanced flow could...

Karoo airborne geophysical survey

International Nuclear Information System (INIS)

Cole, D.J.; Stettler, E.H.

1984-01-01

Thirty four uranium anomalies were selected for ground follow-up from the analogue spectrometer records of Block 4 of the Karoo Airborne Geophysical Survey. The anomalies were plotted on 1:50 000 scale topographic maps and to 1:250 000 scale maps which are included in this report. The anomaly co-ordinates are tabulated together with the farms on which they occur. Results of the ground follow-up of the aerial anomalies are described. Twenty two anomalies are related to uranium mineralisation of which seventeen occur over baked mudstone adjacent to a dolerite intrusion. Five are located over fluvial channel sandstone of the Beaufort Group and subsurface mineralised sandstone may be present. The other twelve anomalies are spurious. Of the anomalies located over baked mudstone, fifteen emanate from ferruginous mudstone of the Whitehill Formation west of longitude 21 degrees 15 minutes. One of the two remaining anomalies over baked mudstone occurs over the Prince Albert Formation and the other anomaly is over baked mudstone and calcareous nodules of the Beaufort Group. The general low uranium values (less than 355 ppm eU3O8) render the occurrences uneconomic

Airborne geoid determination

DEFF Research Database (Denmark)

Forsberg, René; Olesen, Arne Vestergaard; Bastos, L.

2000-01-01

Airborne geoid mapping techniques may provide the opportunity to improve the geoid over vast areas of the Earth, such as polar areas, tropical jungles and mountainous areas, and provide an accurate "seam-less" geoid model across most coastal regions. Determination of the geoid by airborne methods...... relies on the development of airborne gravimetry, which in turn is dependent on developments in kinematic GPS. Routine accuracy of airborne gravimetry are now at the 2 mGal level, which may translate into 5-10 cm geoid accuracy on regional scales. The error behaviour of airborne gravimetry is well......-suited for geoid determination, with high-frequency survey and downward continuation noise being offset by the low-pass gravity to geoid filtering operation. In the paper the basic principles of airborne geoid determination are outlined, and examples of results of recent airborne gravity and geoid surveys...

IMPACT OF DIFFERENT TOPOGRAPHIC CORRECTIONS ON PREDICTION ACCURACY OF FOLIAGE PROJECTIVE COVER (FPC IN A TOPOGRAPHICALLY COMPLEX TERRAIN

Directory of Open Access Journals (Sweden)

S. Ediriweera

2012-07-01

Full Text Available Quantitative retrieval of land surface biological parameters (e.g. foliage projective cover [FPC] and Leaf Area Index is crucial for forest management, ecosystem modelling, and global change monitoring applications. Currently, remote sensing is a widely adopted method for rapid estimation of surface biological parameters in a landscape scale. Topographic correction is a necessary pre-processing step in the remote sensing application for topographically complex terrain. Selection of a suitable topographic correction method on remotely sensed spectral information is still an unresolved problem. The purpose of this study is to assess the impact of topographic corrections on the prediction of FPC in hilly terrain using an established regression model. Five established topographic corrections [C, Minnaert, SCS, SCS+C and processing scheme for standardised surface reflectance (PSSSR] were evaluated on Landsat TM5 acquired under low and high sun angles in closed canopied subtropical rainforest and eucalyptus dominated open canopied forest, north-eastern Australia. The effectiveness of methods at normalizing topographic influence, preserving biophysical spectral information, and internal data variability were assessed by statistical analysis and by comparing field collected FPC data. The results of statistical analyses show that SCS+C and PSSSR perform significantly better than other corrections, which were on less overcorrected areas of faintly illuminated slopes. However, the best relationship between FPC and Landsat spectral responses was obtained with the PSSSR by producing the least residual error. The SCS correction method was poor for correction of topographic effect in predicting FPC in topographically complex terrain.

Modelling of Singapore's topographic transformation based on DEMs

Science.gov (United States)

Wang, Tao; Belle, Iris; Hassler, Uta

2015-02-01

Singapore's topography has been heavily transformed by industrialization and urbanization processes. To investigate topographic changes and evaluate soil mass flows, historical topographic maps of 1924 and 2012 were employed, and basic topographic features were vectorized. Digital elevation models (DEMs) for the two years were reconstructed based on vector features. Corresponding slope maps, a surface difference map and a scatter plot of elevation changes were generated and used to quantify and categorize the nature of the topographic transformation. The surface difference map is aggregated into five main categories of changes: (1) areas without significant height changes, (2) lowered-down areas where hill ranges were cut down, (3) raised-up areas where valleys and swamps were filled in, (4) reclaimed areas from the sea, and (5) new water-covered areas. Considering spatial proximity and configurations of different types of changes, topographic transformation can be differentiated as either creating inland flat areas or reclaiming new land from the sea. Typical topographic changes are discussed in the context of Singapore's urbanization processes. The two slope maps and elevation histograms show that generally, the topographic surface of Singapore has become flatter and lower since 1924. More than 89% of height changes have happened within a range of 20 m and 95% have been below 40 m. Because of differences in land surveying and map drawing methods, uncertainties and inaccuracies inherent in the 1924 topographic maps are discussed in detail. In this work, a modified version of a traditional scatter plot is used to present height transformation patterns intuitively. This method of deriving categorical maps of topographical changes from a surface difference map can be used in similar studies to qualitatively interpret transformation. Slope maps and histograms were also used jointly to reveal additional patterns of topographic change.

Airborne wireless communication systems, airborne communication methods, and communication methods

Science.gov (United States)

Deaton, Juan D [Menan, ID; Schmitt, Michael J [Idaho Falls, ID; Jones, Warren F [Idaho Falls, ID

2011-12-13

An airborne wireless communication system includes circuitry configured to access information describing a configuration of a terrestrial wireless communication base station that has become disabled. The terrestrial base station is configured to implement wireless communication between wireless devices located within a geographical area and a network when the terrestrial base station is not disabled. The circuitry is further configured, based on the information, to configure the airborne station to have the configuration of the terrestrial base station. An airborne communication method includes answering a 911 call from a terrestrial cellular wireless phone using an airborne wireless communication system.

Airborne differential absorption lidar system for measurements of atmospheric water vapor and aerosols

Science.gov (United States)

Carter, Arlen F.; Allen, Robert J.; Mayo, M. Neale; Butler, Carolyn F.; Grossman, Benoist E.; Ismail, Syed; Grant, William B.; Browell, Edward V.; Higdon, Noah S.; Mayor, Shane D.;

Temporal Variability of Upper-level Winds at the Eastern Range, Western Range and Wallops Flight Facility

Science.gov (United States)

Decker, Ryan; Barbre, Robert E.

2014-01-01

Space launch vehicles incorporate upper-level wind profiles to determine wind effects on the vehicle and for a commit to launch decision. These assessments incorporate wind profiles measured hours prior to launch and may not represent the actual wind the vehicle will fly through. Uncertainty in the upper-level winds over the time period between the assessment and launch can be mitigated by a statistical analysis of wind change over time periods of interest using historical data from the launch range. Five sets of temporal wind pairs at various times (.75, 1.5, 2, 3 and 4-hrs) at the Eastern Range, Western Range and Wallops Flight Facility were developed for use in upper-level wind assessments. Database development procedures as well as statistical analysis of temporal wind variability at each launch range will be presented.

VT 100K DRG USGS Topographic Maps

Data.gov (United States)

Vermont Center for Geographic Information — (Link to Metadata) The Vermont Topographic Maps dataset (TOPOVT100K) is a raster image of a scanned USGS 1:100,000 scale topographic map excluding the collar...

Topographic mapping of electroencephalography coherence in hypnagogic state.

Science.gov (United States)

Tanaka, H; Hayashi, M; Hori, T

1998-04-01

The present study examined the topographic characteristics of hypnagogic electroencephalography (EEG), using topographic mapping of EEG power and coherence corresponding to nine EEG stages (Hori's hypnagogic EEG stages). EEG stages 1 and 2, the EEG stages 3-8, and the EEG stage 9 each correspond with standard sleep stage W, 1 and 2, respectively. The dominant topographic components of delta and theta activities increased clearly from the vertex sharp-wave stage (the EEG stages 6 and 7) in the anterior-central areas. The dominant topographic component of alpha 3 activities increased clearly from the EEG stage 9 in the anterior-central areas. The dominant topographic component of sigma activities increased clearly from the EEG stage 8 in the central-parietal area. These results suggested basic sleep process might start before the onset of sleep stage 2 or of the manually scored spindles.

Observations of Munitions Mobility During a Nor'easter at Wallops Island

Science.gov (United States)

Swann, C.; Frank, D. P.; Braithwaite, E. F., III; Hagg, R. K.; Calantoni, J.

2017-12-01

Unexploded ordnance (or munitions) may migrate, bury, or become exposed over time, and may pose a hazard to both humans and environment. Understanding the behavior of munitions under various wave and current conditions is central to management and remediation of contaminated underwater sites. We embedded Inertial Measurement Units (IMUs) into inert replicas of large caliber munitions (81 mm - 155 mm), herein referred to as `smart munitions'. Several smart munitions were deployed in the field with IMUs logging at 16 Hz continuously. Simultaneously the local hydrodynamic conditions were monitored to correlate any resulting munitions mobility. Here, we present the response of the smart munitions to wave and current conditions observed during a nor'easter off the coast of Wallops Island, Virginia USA in about 10 m water depth. During the nor'easter, peak significant wave heights of 2.8 m were observed in 10 m water depth. Over a roughly 10-hour period, an 81 mm smart munition migrated approximately 206 ft in a net onshore direction. Displacement and heading of the migrated smart munition were estimated by divers during the recovery. Integration of the trajectory of motion for the smart munition using a custom signal processing algorithm was in good agreement with the diver measurements. Discussion will focus on the relationship of the local sediment type and the potential for munitions mobility.

Simulating and quantifying legacy topographic data uncertainty: an initial step to advancing topographic change analyses

Science.gov (United States)

Wasklewicz, Thad; Zhu, Zhen; Gares, Paul

2017-12-01

Rapid technological advances, sustained funding, and a greater recognition of the value of topographic data have helped develop an increasing archive of topographic data sources. Advances in basic and applied research related to Earth surface changes require researchers to integrate recent high-resolution topography (HRT) data with the legacy datasets. Several technical challenges and data uncertainty issues persist to date when integrating legacy datasets with more recent HRT data. The disparate data sources required to extend the topographic record back in time are often stored in formats that are not readily compatible with more recent HRT data. Legacy data may also contain unknown error or unreported error that make accounting for data uncertainty difficult. There are also cases of known deficiencies in legacy datasets, which can significantly bias results. Finally, scientists are faced with the daunting challenge of definitively deriving the extent to which a landform or landscape has or will continue to change in response natural and/or anthropogenic processes. Here, we examine the question: how do we evaluate and portray data uncertainty from the varied topographic legacy sources and combine this uncertainty with current spatial data collection techniques to detect meaningful topographic changes? We view topographic uncertainty as a stochastic process that takes into consideration spatial and temporal variations from a numerical simulation and physical modeling experiment. The numerical simulation incorporates numerous topographic data sources typically found across a range of legacy data to present high-resolution data, while the physical model focuses on more recent HRT data acquisition techniques. Elevation uncertainties observed from anchor points in the digital terrain models are modeled using "states" in a stochastic estimator. Stochastic estimators trace the temporal evolution of the uncertainties and are natively capable of incorporating sensor

Airborne Compositae dermatitis

DEFF Research Database (Denmark)

Christensen, Lars Porskjær; Jakobsen, Henrik Byrial; Paulsen, E.

1999-01-01

The air around intact feverfew (Tanacetum parthenium) plants was examined for the presence of airborne parthenolide and other potential allergens using a high-volume air sampler and a dynamic headspace technique. No particle-bound parthenolide was detected in the former. Among volatiles emitted f...... for airborne Compositae dermatitis. Potential allergens were found among the emitted monoterpenes and their importance in airborne Compositae dermatitis is discussed....

Evaluation of Different Topographic Corrections for Landsat TM Data by Prediction of Foliage Projective Cover (FPC in Topographically Complex Landscapes

Directory of Open Access Journals (Sweden)

Sisira Ediriweera

2013-12-01

Full Text Available The reflected radiance in topographically complex areas is severely affected by variations in topography; thus, topographic correction is considered a necessary pre-processing step when retrieving biophysical variables from these images. We assessed the performance of five topographic corrections: (i C correction (C, (ii Minnaert, (iii Sun Canopy Sensor (SCS, (iv SCS + C and (v the Processing Scheme for Standardised Surface Reflectance (PSSSR on the Landsat-5 Thematic Mapper (TM reflectance in the context of prediction of Foliage Projective Cover (FPC in hilly landscapes in north-eastern Australia. The performance of topographic corrections on the TM reflectance was assessed by (i visual comparison and (ii statistically comparing TM predicted FPC with ground measured FPC and LiDAR (Light Detection and Ranging-derived FPC estimates. In the majority of cases, the PSSSR method performed best in terms of eliminating topographic effects, providing the best relationship and lowest residual error when comparing ground measured FPC and LiDAR FPC with TM predicted FPC. The Minnaert, C and SCS + C showed the poorest performance. Finally, the use of TM surface reflectance, which includes atmospheric correction and broad Bidirectional Reflectance Distribution Function (BRDF effects, seemed to account for most topographic variation when predicting biophysical variables, such as FPC.

Biodiversity and Topographic Complexity: Modern and Geohistorical Perspectives

Science.gov (United States)

Badgley, Catherine; Smiley, Tara M.; Terry, Rebecca; Davis, Edward B.; DeSantis, Larisa R.G.; Fox, David L.; Hopkins, Samantha S.B.; Jezkova, Tereza; Matocq, Marjorie D.; Matzke, Nick; McGuire, Jenny L.; Mulch, Andreas; Riddle, Brett R.; Roth, V. Louise; Samuels, Joshua X.; Strömberg, Caroline A.E.; Yanites, Brian J.

2018-01-01

Topographically complex regions on land and in the oceans feature hotspots of biodiversity that reflect geological influences on ecological and evolutionary processes. Over geologic time, topographic diversity gradients wax and wane over millions of years, tracking tectonic or climatic history. Topographic diversity gradients from the present day and the past can result from the generation of species by vicariance or from the accumulation of species from dispersal into a region with strong environmental gradients. Biological and geological approaches must be integrated to test alternative models of diversification along topographic gradients. Reciprocal illumination among phylogenetic, phylogeographic, ecological, paleontological, tectonic, and climatic perspectives is an emerging frontier of biogeographic research. PMID:28196688

Research on Topographic Map Updating

Directory of Open Access Journals (Sweden)

Ivana Javorović

2013-04-01

Full Text Available The investigation of interpretability of panchromatic satellite image IRS-1C integrated with multispectral Landsat TM image with the purpose of updating the topographic map sheet at the scale of 1:25 000 has been described. The geocoding of source map was based on trigonometric points of the map sheet. Satellite images were geocoded using control points selected from the map. The contents of map have been vectorized and topographic database designed. The digital image processing improved the interpretability of images. Then, the vectorization of new contents was made. The change detection of the forest and water area was defined by using unsupervised classification of spatial and spectral merged images. Verification of the results was made using corresponding aerial photographs. Although this methodology could not insure the complete updating of topographic map at the scale of 1:25 000, the database has been updated with huge amount of data. Erdas Imagine 8.3. software was used. 

Topographic characterization of glazed surfaces

International Nuclear Information System (INIS)

Froeberg, Linda; Hupa, Leena

2008-01-01

Detailed characterization of surface microstructure, i.e. phase composition and surface geometry, has become an important criterion of glazed ceramics. Topographic characterization is an important parameter in, e.g. estimating the influence of additional films on the average roughness of a surface. Also, the microscaled and nanoscaled roughnesses correlate with the cleanability and the self-cleaning properties of the surfaces. In this work the surface geometry of several matte glazes were described by topography and roughness as given by whitelight confocal microscopy and atomic force microscopy. Different measuring parameters were compared to justify the usefulness of the techniques in giving a comprehensive description of the surface microstructure. The results suggest that confocal microscopy is well suited for giving reliable topographical parameters for matte surfaces with microscaled crystals in the surfaces. Atomic force microscopy was better suited for smooth surfaces or for describing the local topographic parameters of closely limited areas, e.g. the surroundings of separate crystals in the surface

Topographic characterization of glazed surfaces

Energy Technology Data Exchange (ETDEWEB)

Froeberg, Linda [Process Chemistry Centre, Abo Akademi University, FI-20500 Turku (Finland)], E-mail: lfroberg@abo.fi; Hupa, Leena [Process Chemistry Centre, Abo Akademi University, FI-20500 Turku (Finland)

2008-01-15

Detailed characterization of surface microstructure, i.e. phase composition and surface geometry, has become an important criterion of glazed ceramics. Topographic characterization is an important parameter in, e.g. estimating the influence of additional films on the average roughness of a surface. Also, the microscaled and nanoscaled roughnesses correlate with the cleanability and the self-cleaning properties of the surfaces. In this work the surface geometry of several matte glazes were described by topography and roughness as given by whitelight confocal microscopy and atomic force microscopy. Different measuring parameters were compared to justify the usefulness of the techniques in giving a comprehensive description of the surface microstructure. The results suggest that confocal microscopy is well suited for giving reliable topographical parameters for matte surfaces with microscaled crystals in the surfaces. Atomic force microscopy was better suited for smooth surfaces or for describing the local topographic parameters of closely limited areas, e.g. the surroundings of separate crystals in the surface.

Utilizing Structure-from-Motion Photogrammetry with Airborne Visual and Thermal Images to Monitor Thermal Areas in Yellowstone National Park

Science.gov (United States)

Carr, B. B.; Vaughan, R. G.

2017-12-01

The thermal areas in Yellowstone National Park (Wyoming, USA) are constantly changing. Persistent monitoring of these areas is necessary to better understand the behavior and potential hazards of both the thermal features and the deeper hydrothermal system driving the observed surface activity. As part of the Park's monitoring program, thousands of visual and thermal infrared (TIR) images have been acquired from a variety of airborne platforms over the past decade. We have used structure-from-motion (SfM) photogrammetry techniques to generate a variety of data products from these images, including orthomosaics, temperature maps, and digital elevation models (DEMs). Temperature maps were generated for Upper Geyser Basin and Norris Geyser Basin for the years 2009-2015, by applying SfM to nighttime TIR images collected from an aircraft-mounted forward-looking infrared (FLIR) camera. Temperature data were preserved through the SfM processing by applying a uniform linear stretch over the entire image set to convert between temperature and a 16-bit digital number. Mosaicked temperature maps were compared to the original FLIR image frames and to ground-based temperature data to constrain the accuracy of the method. Due to pixel averaging and resampling, among other issues, the derived temperature values are typically within 5-10 ° of the values of the un-resampled image frame. We also created sub-meter resolution DEMs from airborne daytime visual images of individual thermal areas. These DEMs can be used for resource and hazard management, and in cases where multiple DEMs exist from different times, for measuring topographic change, including change due to thermal activity. For example, we examined the sensitivity of the DEMs to topographic change by comparing DEMs of the travertine terraces at Mammoth Hot Springs, which can grow at > 1 m per year. These methods are generally applicable to images from airborne platforms, including planes, helicopters, and unmanned aerial

History of the topographic branch (division)

Science.gov (United States)

Evans, Richard T.; Frye, Helen M.

2009-01-01

From a very early period of the world's existence, man has endeavored to represent the earth's surface in a graphic form for the information of his fellow men, realizing that no oral or written description is capable of setting forth topographic facts so vividly and so clearly as a map. Mapping of the areas of the United States began with the charting of portions of its coast line by early explorers; the need for topographic maps was first recognized during the war of the Colonies for independence from Great Britain. On July 22, 1777, Congress authorized General Washington to appoint: 'Mr. Robert Erskine, or any other person that he may think proper, geographer and surveyor of the roads, to take sketches of the country and the seat of war.' By several acts during the Revolutionary War, Congress provided 'geographers' for the armies of the United States, some of them with the pay of a colonel, amounting to $60 a month and allowances. At the end of the War, a resolution of May 27, 1785, continued in service the 'geographer of the United States' for a period of 3 years. The War Department recognized the necessity of 'geographical engineers' and requested Congress to authorize their appointment, but it was not until the next war that Congress authorized on March 3, 1813, the appointment of eight topographic engineers and eight assistant topographic engineers under the direction of the General Staff of the Army. These officers formed the nucleus of the first Corps of Topographic Engineers in the Army, and that Corps continued to function as an independent unit until it was absorbed by the Corps of Engineers in 1863, during the Civil War between the States. Between the Louisiana Purchase in 1803, and the outbreak of the Civil War, more than a hundred exploring and mapping expeditions were sent into the vast territory lying west of the Mississippi River to investigate the natural resources of this newly acquired country and to find possible locations for wagon roads to

Airborne Video Surveillance

National Research Council Canada - National Science Library

Blask, Steven

2002-01-01

The DARPA Airborne Video Surveillance (AVS) program was established to develop and promote technologies to make airborne video more useful, providing capabilities that achieve a UAV force multiplier...

Biodiversity and Topographic Complexity: Modern and Geohistorical Perspectives.

Science.gov (United States)

Badgley, Catherine; Smiley, Tara M; Terry, Rebecca; Davis, Edward B; DeSantis, Larisa R G; Fox, David L; Hopkins, Samantha S B; Jezkova, Tereza; Matocq, Marjorie D; Matzke, Nick; McGuire, Jenny L; Mulch, Andreas; Riddle, Brett R; Roth, V Louise; Samuels, Joshua X; Strömberg, Caroline A E; Yanites, Brian J

2017-03-01

Topographically complex regions on land and in the oceans feature hotspots of biodiversity that reflect geological influences on ecological and evolutionary processes. Over geologic time, topographic diversity gradients wax and wane over millions of years, tracking tectonic or climatic history. Topographic diversity gradients from the present day and the past can result from the generation of species by vicariance or from the accumulation of species from dispersal into a region with strong environmental gradients. Biological and geological approaches must be integrated to test alternative models of diversification along topographic gradients. Reciprocal illumination among phylogenetic, phylogeographic, ecological, paleontological, tectonic, and climatic perspectives is an emerging frontier of biogeographic research. Copyright © 2017 Elsevier Ltd. All rights reserved.

Spatial Relation Predicates in Topographic Feature Semantics

Science.gov (United States)

Varanka, Dalia E.; Caro, Holly K.

2013-01-01

Topographic data are designed and widely used for base maps of diverse applications, yet the power of these information sources largely relies on the interpretive skills of map readers and relational database expert users once the data are in map or geographic information system (GIS) form. Advances in geospatial semantic technology offer data model alternatives for explicating concepts and articulating complex data queries and statements. To understand and enrich the vocabulary of topographic feature properties for semantic technology, English language spatial relation predicates were analyzed in three standard topographic feature glossaries. The analytical approach drew from disciplinary concepts in geography, linguistics, and information science. Five major classes of spatial relation predicates were identified from the analysis; representations for most of these are not widely available. The classes are: part-whole (which are commonly modeled throughout semantic and linked-data networks), geometric, processes, human intention, and spatial prepositions. These are commonly found in the ‘real world’ and support the environmental science basis for digital topographical mapping. The spatial relation concepts are based on sets of relation terms presented in this chapter, though these lists are not prescriptive or exhaustive. The results of this study make explicit the concepts forming a broad set of spatial relation expressions, which in turn form the basis for expanding the range of possible queries for topographical data analysis and mapping.

The Combined Use of Airborne Remote Sensing Techniques within a GIS Environment for the Seismic Vulnerability Assessment of Urban Areas: An Operational Application

Directory of Open Access Journals (Sweden)

Antonio Costanzo

2016-02-01

Full Text Available The knowledge of the topographic features, the building properties, and the road infrastructure settings are relevant operational tasks for managing post-crisis events, restoration activities, and for supporting search and rescue operations. Within such a framework, airborne remote sensing tools have demonstrated to be powerful instruments, whose joint use can provide meaningful analyses to support the risk assessment of urban environments. Based on this rationale, in this study, the operational benefits obtained by combining airborne LiDAR and hyperspectral measurements are shown. Terrain and surface digital models are gathered by using LiDAR data. Information about roads and roof materials are provided through the supervised classification of hyperspectral images. The objective is to combine such products within a geographic information system (GIS providing value-added maps to be used for the seismic vulnerability assessment of urban environments. Experimental results are gathered for the city of Cosenza, Italy.

U.S. Topographic Grid

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — isotop.bin - topographic data for conterminous U.S. projected on an 8 km grid. Projection is Albers, central meridian = 96 degrees West, base latitude = 0 degrees...

Specification for the U.S. Geological Survey Historical Topographic Map Collection

Science.gov (United States)

Allord, Gregory J.; Walter, Jennifer L.; Fishburn, Kristin A.; Shea, Gale A.

2014-01-01

This document provides the detailed requirements for producing, archiving, and disseminating a comprehensive digital collection of topographic maps for the U.S. Geological Survey (USGS) Historical Topographic Map Collection (HTMC). The HTMC is a digital archive of about 190,000 printed topographic maps published by the USGS from the inception of the topographic mapping program in 1884 until the last paper topographic map using lithographic printing technology was published in 2006. The HTMC provides a comprehensive digital repository of all scales and all editions of USGS printed topographic maps that is easily discovered, browsed, and downloaded by the public at no cost. The HTMC provides ready access to maps that are no longer available for distribution in print. A digital file representing the original paper historical topographic map is produced for each historical map in the HTMC in georeferenced PDF (GeoPDF) format (a portable document format [PDF] with a geospatial extension).

Airborne detection of magnetic anomalies associated with soils on the Oak Ridge Reservation, Tennessee

International Nuclear Information System (INIS)

Doll, W.E.; Beard, L.P.; Helm, J.M.

1995-01-01

Reconnaissance airborne geophysical data acquired over the 35,000-acre Oak Ridge Reservation (ORR), TN, show several magnetic anomalies over undisturbed areas mapped as Copper Ridge Dolomite (CRD). The anomalies of interest are most apparent in magnetic gradient maps where they exceed 0.06 nT/m and in some cases exceed 0.5 nT/m. Anomalies as large as 25nT are seen on maps. Some of the anomalies correlate with known or suspected karst, or with apparent conductivity anomalies calculated from electromagnetic data acquired contemporaneously with the magnetic data. Some of the anomalies have a strong correlation with topographic lows or closed depressions. Surface magnetic data have been acquired over some of these sites and have confirmed the existence of the anomalies. Ground inspections in the vicinity of several of the anomalies has not led to any discoveries of manmade surface materials of sufficient size to generate the observed anomalies. One would expect an anomaly of approximately 1 nT for a pickup truck from 200 ft altitude. Typical residual magnetic anomalies have magnitudes of 5--10 nT, and some are as large as 25nT. The absence of roads or other indications of culture (past or present) near the anomalies and the modeling of anomalies in data acquired with surface instruments indicate that man-made metallic objects are unlikely to be responsible for the anomaly. The authors show that observed anomalies in the CRD can reasonably be associated with thickening of the soil layer. The occurrence of the anomalies in areas where evidences of karstification are seen would follow because sediment deposition would occur in topographic lows. Linear groups of anomalies on the maps may be associated with fracture zones which were eroded more than adjacent rocks and were subsequently covered with a thicker blanket of sediment. This study indicates that airborne magnetic data may be of use in other sites where fracture zones or buried collapse structures are of interest

Ontology patterns for complex topographic feature yypes

Science.gov (United States)

Varanka, Dalia E.

2011-01-01

Complex feature types are defined as integrated relations between basic features for a shared meaning or concept. The shared semantic concept is difficult to define in commonly used geographic information systems (GIS) and remote sensing technologies. The role of spatial relations between complex feature parts was recognized in early GIS literature, but had limited representation in the feature or coverage data models of GIS. Spatial relations are more explicitly specified in semantic technology. In this paper, semantics for topographic feature ontology design patterns (ODP) are developed as data models for the representation of complex features. In the context of topographic processes, component assemblages are supported by resource systems and are found on local landscapes. The topographic ontology is organized across six thematic modules that can account for basic feature types, resource systems, and landscape types. Types of complex feature attributes include location, generative processes and physical description. Node/edge networks model standard spatial relations and relations specific to topographic science to represent complex features. To demonstrate these concepts, data from The National Map of the U. S. Geological Survey was converted and assembled into ODP.

Topographic precursors and geological structures of deep-seated catastrophic landslides caused by typhoon Talas, determined from the analysis of high-resolution DEMs

Science.gov (United States)

Chigira, Masahiro; Tsou, Ching-Ying; Matsushi, Yuki

2013-04-01

Typhoon Talas crossed the Japanese Islands between 2 and 5 September 2011, causing more than 70 deep-seated catastrophic landslides in a Jurassic to Paleogene-Early Miocene accretion complex. Detailed examination of the topographic features of 10 large landslides before the event, recorded on DEMs with a resolution of 1 m (based on airborne laser scanner surveys), showed that all of the landslides had small scarplets near their future crowns prior to the slide, and one landslide had linear depressions along its future crown as precursor topographic features. These scarplets and linear depressions were caused by gravitational slope deformation that preceded the catastrophic failure. Strains, defined by the ratio of the length of a scarplet to the length of the whole slope (as measured along the slope line), ranged from 5% to 21%, and are the first reliable numerical data relating to the topographic precursor features of large and catastrophic landslides. Careful examination of aerial photographs from another four large landslides, for which no high-resolution DEMs were available, suggested that they also developed scarplets at their heads beforehand, which are not precisely quantified. Twelve of the 14 landslides we surveyed in the field had sliding surfaces with wedge-shaped discontinuities that consisted of faults, shear surfaces that formed during accretion, and bedding, suggesting that the buildup of pore pressure occurs readily in a gravitationally deformed rock body containing wedge-shaped discontinuities. Other types of gravitational deformation were also active; e.g., flexural toppling and buckling were each observed to have preceded one landslide.

Comparative analysis of extracted heights from topographic maps ...

African Journals Online (AJOL)

Topographic maps represent the three-dimensional landscape by providing relief information in the form of contours in addition to plan information on which natural and man-made landmarks are quite accurately represented. Height information, extractible from topographic maps, comes in handy for most land use planning.

The modulation of canine mesenchymal stem cells by nano-topographic cues

International Nuclear Information System (INIS)

Wood, Joshua A.; Ly, Irene; Borjesson, Dori L.; Nealey, Paul F.; Russell, Paul; Murphy, Christopher J.

2012-01-01

Mesenchymal stem cells (MSCs) represent a promising cellular therapeutic for the treatment of a variety of disorders. On transplantation, MSCs interact with diverse extracellular matrices (ECMs) that vary dramatically in topographic feature type, size and surface order. In order to investigate the impact of these topographic cues, surfaces were fabricated with either isotropically ordered holes or anisotropically ordered ridges and grooves. To simulate the biologically relevant nano through micron size scale, a series of topographically patterned substrates possessing features of differing pitch (pitch=feature width+groove width) were created. Results document that the surface order and size of substratum topographic features dramatically modulate fundamental MSC behaviors. Topographically patterned (ridge+groove) surfaces were found to significantly impact MSC alignment, elongation, and aspect ratio. Novel findings also demonstrate that submicron surfaces patterned with holes resulted in increased MSC alignment to adjacent cells as well as increased migration rates. Overall, this study demonstrates that the presentation of substratum topographic cues dramatically influence MSC behaviors in a size and shape dependent manner. The response of MSCs to substratum topographic cues was similar to other cell types that have been studied previously with regards to cell shape on ridge and groove surfaces but differed with respect to proliferation and migration. This is the first study to compare the impact of anisotropically ordered ridge and groove topographic cues to isotropically order holed topographic cues on fundamental MSC behaviors across a range of biologically relevant size scales.

The modulation of canine mesenchymal stem cells by nano-topographic cues

Energy Technology Data Exchange (ETDEWEB)

Wood, Joshua A.; Ly, Irene [Department of Surgical and Radiological Sciences, School of Veterinary Medicine, University of California, Davis (United States); Borjesson, Dori L. [Department of Pathology, Microbiology, and Immunology, School of Veterinary Medicine, University of California, Davis (United States); Nealey, Paul F. [Department of Chemical and Biological Engineering, School of Engineering, University of Wisconsin-Madison (United States); Russell, Paul [Department of Surgical and Radiological Sciences, School of Veterinary Medicine, University of California, Davis (United States); Murphy, Christopher J., E-mail: cjmurphy@ucdavis.edu [Department of Surgical and Radiological Sciences, School of Veterinary Medicine, University of California, Davis (United States); Department of Ophthalmology and Vision Sciences, School of Medicine, University of California, Davis (United States)

2012-11-15

Mesenchymal stem cells (MSCs) represent a promising cellular therapeutic for the treatment of a variety of disorders. On transplantation, MSCs interact with diverse extracellular matrices (ECMs) that vary dramatically in topographic feature type, size and surface order. In order to investigate the impact of these topographic cues, surfaces were fabricated with either isotropically ordered holes or anisotropically ordered ridges and grooves. To simulate the biologically relevant nano through micron size scale, a series of topographically patterned substrates possessing features of differing pitch (pitch=feature width+groove width) were created. Results document that the surface order and size of substratum topographic features dramatically modulate fundamental MSC behaviors. Topographically patterned (ridge+groove) surfaces were found to significantly impact MSC alignment, elongation, and aspect ratio. Novel findings also demonstrate that submicron surfaces patterned with holes resulted in increased MSC alignment to adjacent cells as well as increased migration rates. Overall, this study demonstrates that the presentation of substratum topographic cues dramatically influence MSC behaviors in a size and shape dependent manner. The response of MSCs to substratum topographic cues was similar to other cell types that have been studied previously with regards to cell shape on ridge and groove surfaces but differed with respect to proliferation and migration. This is the first study to compare the impact of anisotropically ordered ridge and groove topographic cues to isotropically order holed topographic cues on fundamental MSC behaviors across a range of biologically relevant size scales.

Topographic precursors and geological structures of deep-seated catastrophic landslides caused by Typhoon Talas

Science.gov (United States)

Chigira, Masahiro; Tsou, Ching-Ying; Matsushi, Yuki; Hiraishi, Narumi; Matsuzawa, Makoto

2013-11-01

Typhoon Talas crossed the Japanese Islands between 2 and 5 September 2011, causing more than 70 deep-seated catastrophic landslides in a Jurassic to Paleogene-lower Miocene accretion complex. Detailed examination of the topographic features of 10 large landslides before the event, recorded on 1-m DEMs based on airborne laser scanner surveys, showed that all landslides had small scarps near their future crowns prior to the slide, and one landslide had linear depressions along its future crown as precursor topographic features. These scarps and linear depressions were caused by gravitational slope deformation that preceded the catastrophic failure. Although the scarps may have been enlarged by degradation, their sizes relative to the whole slopes suggest that minimal slope deformation had occurred in the period immediately before the catastrophic failure. The scarp ratio, defined as the ratio of length of a scarp to that of the whole slope both measured along the slope line, ranged from 5% to 21%. Careful examination of aerial photographs from another four large landslides, for which no high-resolution DEMs were available, suggested that they also developed scarps at their heads beforehand. Twelve of the 14 landslides we surveyed in the field had sliding surfaces with wedge-shaped discontinuities that consisted of faults and bedding, suggesting that the buildup of pore pressure occurs readily on wedge-shaped discontinuities in a gravitationally deformed rock body. Most of the faults were undulatory and were probably thrust faults that formed during accretion. Other types of gravitational deformation were also active; e.g., flexural toppling and buckling were observed to have preceded one landslide.

Seafloor Topographic Analysis in Staged Ocean Resource Exploration

Science.gov (United States)

Ikeda, M.; Okawa, M.; Osawa, K.; Kadoshima, K.; Asakawa, E.; Sumi, T.

2017-12-01

J-MARES (Research and Development Partnership for Next Generation Technology of Marine Resources Survey, JAPAN) has been designing a low-expense and high-efficiency exploration system for seafloor hydrothermal massive sulfide deposits in "Cross-ministerial Strategic Innovation Promotion Program (SIP)" granted by the Cabinet Office, Government of Japan since 2014. We designed a method to focus mineral deposit prospective area in multi-stages (the regional survey, semi-detail survey and detail survey) by extracted topographic features of some well-known seafloor massive sulfide deposits from seafloor topographic analysis using seafloor topographic data acquired by the bathymetric survey. We applied this procedure to an area of interest more than 100km x 100km over Okinawa Trough, including some known seafloor massive sulfide deposits. In Addition, we tried to create a three-dimensional model of seafloor topography by SfM (Structure from Motion) technique using multiple image data of Chimney distributed around well-known seafloor massive sulfide deposit taken with Hi-Vision camera mounted on ROV in detail survey such as geophysical exploration. Topographic features of Chimney was extracted by measuring created three-dimensional model. As the result, it was possible to estimate shape of seafloor sulfide such as Chimney to be mined by three-dimensional model created from image data taken with camera mounted on ROV. In this presentation, we will discuss about focusing mineral deposit prospective area in multi-stages by seafloor topographic analysis using seafloor topographic data in exploration system for seafloor massive sulfide deposit and also discuss about three-dimensional model of seafloor topography created from seafloor image data taken with ROV.

Airborne radionuclide waste-management reference document

International Nuclear Information System (INIS)

Brown, R.A.; Christian, J.D.; Thomas, T.R.

1983-07-01

This report provides the detailed data required to develop a strategy for airborne radioactive waste management by the Department of Energy (DOE). The airborne radioactive materials of primary concern are tritium (H-3), carbon-14 (C-14), krypton-85 (Kr-85), iodine-129 (I-129), and radioactive particulate matter. The introductory section of the report describes the nature and broad objectives of airborne waste management. The relationship of airborne waste management to other waste management programs is described. The scope of the strategy is defined by considering all potential sources of airborne radionuclides and technologies available for their management. Responsibilities of the regulatory agencies are discussed. Section 2 of this document deals primarily with projected inventories, potential releases, and dose commitments of the principal airborne wastes from the light water reactor (LWR) fuel cycle. In Section 3, dose commitments, technologies, costs, regulations, and waste management criteria are analyzed. Section 4 defines goals and objectives for airborne waste management

Nighttime ionization by energetic particles at Wallops Island in the altitude region 120 to 200 km

International Nuclear Information System (INIS)

Voss, H.D.; Smith, L.G.

1979-01-01

Five Nike Apache rockets, each including an energetic particle spectrometer and an electron density-electron temperature experiment, have been launched from Wallops Island (L=2.6) near midnight under varying geomagnetic conditions. On the most recent of these (5 January 1978) an additional spectrometer with a broom magnet, and a 391.4 nm photometer were flown. The data from this flight indicate that the energetic particle flux consists predominantly of protons, neutral hydrogen and possibly other energetic nuclei. The energy spectrum becomes much softer and the flux more intense with increasing Kp for 10 0 indicating that the majority of particles are near their mirroring altitude. Ionization rates are calculated based on the measured energy spectrum and mirror height distribution. The resulting ionization rate profile is found to be nearly constant with altitude in the region 120 to 200 km. The measured energetic particle flux and calculated ionization rate from the five flights are found to vary with magnetic activity (based on the Kp and Dst indexes) in the same way as the independently derived ionization rates deduced from the electron density profile

Airborne relay-based regional positioning system.

Science.gov (United States)

Lee, Kyuman; Noh, Hongjun; Lim, Jaesung

2015-05-28

Ground-based pseudolite systems have some limitations, such as low vertical accuracy, multipath effects and near-far problems. These problems are not significant in airborne-based pseudolite systems. However, the monitoring of pseudolite positions is required because of the mobility of the platforms on which the pseudolites are mounted, and this causes performance degradation. To address these pseudolite system limitations, we propose an airborne relay-based regional positioning system that consists of a master station, reference stations, airborne relays and a user. In the proposed system, navigation signals are generated from the reference stations located on the ground and are relayed via the airborne relays. Unlike in conventional airborne-based systems, the user in the proposed system sequentially estimates both the locations of airborne relays and his/her own position. Therefore, a delay due to monitoring does not occur, and the accuracy is not affected by the movement of airborne relays. We conducted several simulations to evaluate the performance of the proposed system. Based on the simulation results, we demonstrated that the proposed system guarantees a higher accuracy than airborne-based pseudolite systems, and it is feasible despite the existence of clock offsets among reference stations.

Optical Airborne Tracker System

Data.gov (United States)

National Aeronautics and Space Administration — The Optical Airborne Tracker System (OATS) is an airborne dual-axis optical tracking system capable of pointing at any sky location or ground target.  The objectives...

The chang’E-1 topographic atlas of the Moon

CERN Document Server

Li, Chunlai; Mu, Lingli; Ren, Xin; Zuo, Wei

2016-01-01

This atlas is based on the lunar global Digital Elevation Models (DEM) of Chang'E-1 (CE-1), and presents CCD stereo image data with digital photogrammetry. The spatial resolution of the DEM in this atlas is 500m, with horizontal accuracy of 192m and vertical accuracy of 120m. Color-shaded relief maps with contour lines are used to show the lunar topographical characteristics. The topographical data gathered by CE-1 can provide fundamental information for the study of lunar topographical, morphological and geological structures, as well as for lunar evolution research.

2013 NOAA Oahu Topographic Lidar

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The Oahu, Hawaii Elevation Data Task Order involves collecting and delivering topographic elevation point data derived from multiple return light detection and...

Airborne full tensor magnetic gradiometry surveys in the Thuringian basin, Germany

Science.gov (United States)

Queitsch, M.; Schiffler, M.; Goepel, A.; Stolz, R.; Meyer, M.; Meyer, H.; Kukowski, N.

2013-12-01

In this contribution we introduce a newly developed fully operational full tensor magnetic gradiometer (FTMG) instrument based on Superconducting Quantum Interference Devices (SQUIDs) and show example data acquired in 2012 within the framework of the INFLUINS (Integrated Fluid Dynamics in Sedimentary basins) project. This multidisciplinary project aims for a better understanding of movements and interaction between shallow and deep fluids in the Thuringian Basin in the center of Germany. In contrast to mapping total magnetic field intensity (TMI) in conventional airborne magnetic surveys for industrial exploration of mineral deposits and sedimentary basins, our instrument measures all components of the magnetic field gradient tensor using highly sensitive SQUID gradiometers. This significantly constrains the solutions of the inverse problem. Furthermore, information on the ratio between induced and remanent magnetization is obtained. Special care has been taken to reduce motion noise while acquiring data in airborne operation. Therefore, the sensors are mounted in a nonmagnetic and aerodynamically shaped bird made of fiberglas with a high drag tail which stabilizes the bird even at low velocities. The system is towed by a helicopter and kept at 30m above ground during data acquisition. Additionally, the system in the bird incorporates an inertial unit for geo-referencing and enhanced motion noise compensation, a radar altimeter for topographic correction and a GPS system for high precision positioning. Advanced data processing techniques using reference magnetometer and inertial unit data result in a very low system noise of less than 60 pT/m peak to peak in airborne operation. To show the performance of the system we present example results from survey areas within the Thuringian basin and along its bordering highlands. The mapped gradient tensor components show a high correlation to existing geologic maps. Furthermore, the measured gradient components indicate

Airborne Tactical Crossload Planner

Science.gov (United States)

2017-12-01

Regiment AGL above ground level AO area of operation APA American psychological association ASOP airborne standard operating procedure A/C aircraft...awarded a research contract to develop a tactical crossload tool. [C]omputer assisted Airborne Planning Application ( APA ) that provides a

On regulation of radioactive airborne discharge

International Nuclear Information System (INIS)

Stroganov, A.A.; Kuryndin, A.V.; Shapovalov, A.S.; Orlov, M.Yu.

2013-01-01

Authors present the Russian regulatory basis of radioactive airborne discharges which was updated after enactment of the Methodology for airborne discharge limits development. Criteria for establishing of airborne discharge limits, scope and other features of methodology are also considered in the article [ru

USGS Historical Topographic Map Collection

Data.gov (United States)

U.S. Geological Survey, Department of the Interior — USGS Historical Quadrangle in GeoPDF. The USGS Historical Quadrangle Scanning Project (HQSP) is scanning all scales and all editions of topographic maps published by...

Glacier development and topographic context

DEFF Research Database (Denmark)

López-Moreno, J. I.; Nogués-Bravo, David; Chueca-Cía, J.

2006-01-01

This paper analyses the topographic context of the remaining glaciated areas in the Maladeta Massif (Central Spanish Pyrenees). These ice-covered surfaces have been incorporated into a geographic information system (GIS) in an attempt at correlating the presence of ice with a range of topographic...... and recent evolution of each glacial body. Thus, the joint effect of altitude, exposure to incoming solar radiation, slope and mean curvature is able to explain more than 70 per cent of the observed variance. Copyright © 2006 John Wiley & Sons, Ltd....... variables obtained from a digital elevation model. The use of generalized additive models and binary regression tree models enabled us (i) to quantify the spatial variability in the distribution of glaciers attributable to characteristics of the local terrain, (ii) to investigate the interaction between...

A simulator for airborne laser swath mapping via photon counting

Science.gov (United States)

Slatton, K. C.; Carter, W. E.; Shrestha, R.

2005-06-01

Commercially marketed airborne laser swath mapping (ALSM) instruments currently use laser rangers with sufficient energy per pulse to work with return signals of thousands of photons per shot. The resulting high signal to noise level virtually eliminates spurious range values caused by noise, such as background solar radiation and sensor thermal noise. However, the high signal level approach requires laser repetition rates of hundreds of thousands of pulses per second to obtain contiguous coverage of the terrain at sub-meter spatial resolution, and with currently available technology, affords little scalability for significantly downsizing the hardware, or reducing the costs. A photon-counting ALSM sensor has been designed by the University of Florida and Sigma Space, Inc. for improved topographic mapping with lower power requirements and weight than traditional ALSM sensors. Major elements of the sensor design are presented along with preliminary simulation results. The simulator is being developed so that data phenomenology and target detection potential can be investigated before the system is completed. Early simulations suggest that precise estimates of terrain elevation and target detection will be possible with the sensor design.

The Role of Emotional Landmarks on Topographical Memory.

Science.gov (United States)

Palmiero, Massimiliano; Piccardi, Laura

2017-01-01

The investigation of the role of emotional landmarks on human navigation has been almost totally neglected in psychological research. Therefore, the extent to which positive and negative emotional landmarks affect topographical memory as compared to neutral emotional landmark was explored. Positive, negative and neutral affect-laden images were selected as landmarks from the International Affective Picture System (IAPS) Inventory. The Walking Corsi test (WalCT) was used in order to test the landmark-based topographical memory. Participants were instructed to learn and retain an eight-square path encompassing positive, negative or neutral emotional landmarks. Both egocentric and allocentric frames of references were considered. Egocentric representation encompasses the object's relation to the self and it is generated from sensory data. Allocentric representation expresses a location with respect to an external frame regardless of the self and it is the basis for long-term storage of complex layouts. In particular, three measures of egocentric and allocentric topographical memory were taken into account: (1) the ability to learn the path; (2) the ability to recall by walking the path five minutes later; (3) the ability to reproduce the path on the outline of the WalCT. Results showed that both positive and negative emotional landmarks equally enhanced the learning of the path as compared to neutral emotional landmarks. In addition, positive emotional landmarks improved the reproduction of the path on the map as compared to negative and neutral emotional landmarks. These results generally show that emotional landmarks enhance egocentric-based topographical memory, whereas positive emotional landmarks seem to be more effective for allocentric-based topographical memory.

Airborne geophysical radon hazard mapping

International Nuclear Information System (INIS)

Walker, P.

1993-01-01

Shales containing uranium pose a radon health hazard even when covered by several meters of overburden. Such an alum shale in southern Norway has been mapped with a joint helicopter borne electromagnetic (HEM) and radiometric survey. Results are compared with ground spectrometer, radon emanometer and radon gas measurements in dwellings, and a model to predict radon gas concentrations from the airborne data is developed. Since the shale is conductive, combining the HEM data with the radiometric channel allows the shale to be mapped with greater reliability than if the radiometric channel were used alone. Radiometrically more active areas which do not pose a radon gas hazard can thus be separated from the shales which do. The ground follow-up work consisted of spectrometer and radon emanometer measurements over a uranium anomaly coinciding with a conductor. The correlation between the airborne uranium channel, the ground uranium channel and emanometry is extremely good, indicating that airborne geophysics can, in this case, be used to predict areas having a high radon potential. Contingency tables comparing both radon exhalation and concentration in dwellings with the airborne uranium data show a strong relationship exists between exhalation and the airborne data and while a relationship between concentration and the airborne data is present, but weaker

The Relationship between Vestibular Function and Topographical Memory in Older Adults

Directory of Open Access Journals (Sweden)

Fred Henry Previc

2014-06-01

Full Text Available Research during the past two decades has demonstrated an important role of the vestibular system in topographical orientation and memory and the network of neural structures associated with them. Almost all of the supporting data have come from animal or human clinical studies, however. The purpose of the present study was to investigate the link between vestibular function and topographical memory in normal elderly humans. Twenty-five participants aged 70 to 85 years who scored from mildly impaired to normal on the Montreal Cognitive Assessment received three topographical memory tests: the Camden Topographical Recognition Memory Test (CTMRT, a computerized topographical mental rotation test (TMRT, and a virtual pond maze (VPM. They also received six vestibular or oculomotor tests: optokinetic nystagmus (OKN, visual pursuit (VP, actively generated vestibulo-ocular reflex (VOR, the sensory orientation test (SOT for posture, and two measures of rotational memory (error in degrees, or RMº, and correct directional recognition, or RM→. The only significant bivariate correlations were among the three vestibular measures primarily assessing horizontal canal function (VOR, RMº, and RM→. A multiple regression analysis showed significant relationships between vestibular and demographic predictors and both the TMRT (R=.78 and VPM (R=.66 measures. The significant relationship between the vestibular and topographical memory measures supports the theory that vestibular loss may contribute to topographical memory impairment in the elderly.

Routing architecture and security for airborne networks

Science.gov (United States)

Deng, Hongmei; Xie, Peng; Li, Jason; Xu, Roger; Levy, Renato

2009-05-01

Airborne networks are envisioned to provide interconnectivity for terrestial and space networks by interconnecting highly mobile airborne platforms. A number of military applications are expected to be used by the operator, and all these applications require proper routing security support to establish correct route between communicating platforms in a timely manner. As airborne networks somewhat different from traditional wired and wireless networks (e.g., Internet, LAN, WLAN, MANET, etc), security aspects valid in these networks are not fully applicable to airborne networks. Designing an efficient security scheme to protect airborne networks is confronted with new requirements. In this paper, we first identify a candidate routing architecture, which works as an underlying structure for our proposed security scheme. And then we investigate the vulnerabilities and attack models against routing protocols in airborne networks. Based on these studies, we propose an integrated security solution to address routing security issues in airborne networks.

Complex Topographic Feature Ontology Patterns

Science.gov (United States)

Varanka, Dalia E.; Jerris, Thomas J.

2015-01-01

Semantic ontologies are examined as effective data models for the representation of complex topographic feature types. Complex feature types are viewed as integrated relations between basic features for a basic purpose. In the context of topographic science, such component assemblages are supported by resource systems and found on the local landscape. Ontologies are organized within six thematic modules of a domain ontology called Topography that includes within its sphere basic feature types, resource systems, and landscape types. Context is constructed not only as a spatial and temporal setting, but a setting also based on environmental processes. Types of spatial relations that exist between components include location, generative processes, and description. An example is offered in a complex feature type ‘mine.’ The identification and extraction of complex feature types are an area for future research.

The Role of Emotional Landmarks on Topographical Memory

Directory of Open Access Journals (Sweden)

Massimiliano Palmiero

2017-05-01

Full Text Available The investigation of the role of emotional landmarks on human navigation has been almost totally neglected in psychological research. Therefore, the extent to which positive and negative emotional landmarks affect topographical memory as compared to neutral emotional landmark was explored. Positive, negative and neutral affect-laden images were selected as landmarks from the International Affective Picture System (IAPS Inventory. The Walking Corsi test (WalCT was used in order to test the landmark-based topographical memory. Participants were instructed to learn and retain an eight-square path encompassing positive, negative or neutral emotional landmarks. Both egocentric and allocentric frames of references were considered. Egocentric representation encompasses the object’s relation to the self and it is generated from sensory data. Allocentric representation expresses a location with respect to an external frame regardless of the self and it is the basis for long-term storage of complex layouts. In particular, three measures of egocentric and allocentric topographical memory were taken into account: (1 the ability to learn the path; (2 the ability to recall by walking the path five minutes later; (3 the ability to reproduce the path on the outline of the WalCT. Results showed that both positive and negative emotional landmarks equally enhanced the learning of the path as compared to neutral emotional landmarks. In addition, positive emotional landmarks improved the reproduction of the path on the map as compared to negative and neutral emotional landmarks. These results generally show that emotional landmarks enhance egocentric-based topographical memory, whereas positive emotional landmarks seem to be more effective for allocentric-based topographical memory.

Simulation of machine-specific topographic indices for use across platforms.

Science.gov (United States)

Mahmoud, Ashraf M; Roberts, Cynthia; Lembach, Richard; Herderick, Edward E; McMahon, Timothy T

2006-09-01

The objective of this project is to simulate the current published topographic indices used for the detection and evaluation of keratoconus to allow their application to maps acquired from multiple topographic machines. A retrospective analysis was performed on 21 eyes of 14 previously diagnosed keratoconus patients from a single practice using a Tomey TMS-1, an Alcon EyeMap, and a Keratron Topographer. Maps that could not be processed or that contained processing errors were excluded from analysis. Topographic indices native to each of the three devices were recorded from each map. Software was written in ANSI standard C to simulate the indices based on the published formulas and/or descriptions to extend the functionality of The Ohio State University Corneal Topography Tool (OSUCTT), a software package designed to accept the input from many corneal topographic devices and provide consistent display and analysis. Twenty indices were simulated. Linear regression analysis was performed between each simulated index and the corresponding native index. A cross-platform comparison using regression analysis was also performed. All simulated indices were significantly correlated with the corresponding native indices (p simulated. Cross-platform comparisons may be limited for specific indices.

Airborne Cloud Computing Environment (ACCE)

Science.gov (United States)

Hardman, Sean; Freeborn, Dana; Crichton, Dan; Law, Emily; Kay-Im, Liz

2011-01-01

Airborne Cloud Computing Environment (ACCE) is JPL's internal investment to improve the return on airborne missions. Improve development performance of the data system. Improve return on the captured science data. The investment is to develop a common science data system capability for airborne instruments that encompasses the end-to-end lifecycle covering planning, provisioning of data system capabilities, and support for scientific analysis in order to improve the quality, cost effectiveness, and capabilities to enable new scientific discovery and research in earth observation.

2011 SWFWMD Topographic Lidar: Hillsborough County

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — SWFWMD regularly uses digital topographic information to support regulatory, land management and acquisition, planning, engineering and habitat restoration projects....

2011 SWFWMD Topographic Lidar: Pasco County

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — SWFWMD regularly uses digital topographic information to support regulatory, land management and acquisition, planning, engineering and habitat restoration projects....

AIRBORNE LASER BATHYMETRY FOR DOCUMENTATION OF SUBMERGED ARCHAEOLOGICAL SITES IN SHALLOW WATER

Directory of Open Access Journals (Sweden)

M. Doneus

2015-04-01

Full Text Available Knowledge of underwater topography is essential to the understanding of the organisation and distribution of archaeological sites along and in water bodies. Special attention has to be paid to intertidal and inshore zones where, due to sea-level rise, coastlines have changed and many former coastal sites are now submerged in shallow water. Mapping the detailed inshore topography is therefore important to reconstruct former coastlines, identify sunken archaeological structures and locate potential former harbour sites. However, until recently archaeology has lacked suitable methods to provide the required topographical data of shallow underwater bodies. Our research shows that airborne topo-bathymetric laser scanner systems are able to measure surfaces above and below the water table over large areas in high detail using very short and narrow green laser pulses, even revealing sunken archaeological structures in shallow water. Using an airborne laser scanner operating at a wavelength in the green visible spectrum (532 nm two case study areas in different environmental settings (Kolone, Croatia, with clear sea water; Lake Keutschach, Austria, with turbid water were scanned. In both cases, a digital model of the underwater topography with a planimetric resolution of a few decimeters was measured. While in the clear waters of Kolone penetration depth was up to 11 meters, turbid Lake Keutschach allowed only to document the upper 1.6 meters of its underwater topography. Our results demonstrate the potential of this technique to map submerged archaeological structures over large areas in high detail providing the possibility for systematic, large scale archaeological investigation of this environment.

Potential of a novel airborne hydrographic laser scanner for capturing shallow water bodies

Science.gov (United States)

Mandlburger, G.; Pfennigbauer, M.; Steinbacher, F.; Pfeifer, N.

2012-04-01

In this paper, we present the general design of a hydrographic laser scanner (prototype instrument) manufactured by the company Riegl Laser Measurement Systems in cooperation with the University of Innsbruck, Unit of Hydraulic Engineering. The instrument utilizes very short laser pulses (1 ns) in the green wavelength domain (λ=532 nm) capable of penetrating the water column. The backscattered signal is digitized in a waveform recorder at high frequency enabling sophisticated waveform processing, both, online during the flight and in post processing. In combination with a traditional topographic airborne laser scanner (λ=1500 nm) mounted on the same platform a complete hydrographic and topographic survey of the riparian foreland, the water surface and river bed can be carried out in a single campaign. In contrast to existing bathymetric LiDAR systems, the presented system uses only medium pulse energy but a high pulse repetition rate of up to 250 kHz and, thus, focuses on a detailed description of shallow water bodies under clear water conditions. Different potential fields of applications of the instrument (hydraulic modelling, hydro-morphology, hydro-biology, ecology, river restoration and monitoring) are discussed and the results of first real-world test flights in Austria and Germany are presented. It is shown that: (i) the high pulse repetition rate enables a point density on the ground of the water body of 10-20 pts/m2, (ii) the short laser pulses together with waveform processing enable a discrimination between water and ground reflections at a water depth of less than 25 cm, (iii) the combination of a topographic and hydrographic laser scanner enable the acquisition of the geometry data for hydraulic modeling in a single survey, thus, providing a much more homogeneous data basis compared to traditional techniques, and (iv) the high point density and the ranging accuracy of less than 10 cm enable a detailed and precise description of the river bed

Monitoring and evaluation techniques for airborne contamination

Energy Technology Data Exchange (ETDEWEB)

Yihua, Xia [China Inst. of Atomic Energy, Beijing (China)

1997-06-01

Monitoring and evaluation of airborne contamination are of great importance for the purpose of protection of health and safety of workers in nuclear installations. Because airborne contamination is one of the key sources to cause exposure to individuals by inhalation and digestion, and to cause diffusion of contaminants in the environment. The main objectives of monitoring and evaluation of airborne contamination are: to detect promptly a loss of control of airborne material, to help identify those individuals and predict exposure levels, to assess the intake and dose commitment to the individuals, and to provide sufficient documentation of airborne radioactivity. From the viewpoint of radiation protection, the radioactive contaminants in air can be classified into the following types: airborne aerosol, gas and noble gas, and volatile gas. In this paper, the following items are described: sampling methods and techniques, measurement and evaluation, and particle size analysis. (G.K.)

Monitoring and evaluation techniques for airborne contamination

International Nuclear Information System (INIS)

Xia Yihua

1997-01-01

Monitoring and evaluation of airborne contamination are of great importance for the purpose of protection of health and safety of workers in nuclear installations. Because airborne contamination is one of the key sources to cause exposure to individuals by inhalation and digestion, and to cause diffusion of contaminants in the environment. The main objectives of monitoring and evaluation of airborne contamination are: to detect promptly a loss of control of airborne material, to help identify those individuals and predict exposure levels, to assess the intake and dose commitment to the individuals, and to provide sufficient documentation of airborne radioactivity. From the viewpoint of radiation protection, the radioactive contaminants in air can be classified into the following types: airborne aerosol, gas and noble gas, and volatile gas. In this paper, the following items are described: sampling methods and techniques, measurement and evaluation, and particle size analysis. (G.K.)

Topographical Hill Shading Map Production Based Tianditu (map World)

Science.gov (United States)

Wang, C.; Zha, Z.; Tang, D.; Yang, J.

2018-04-01

TIANDITU (Map World) is the public version of National Platform for Common Geospatial Information Service, and the terrain service is an important channel for users on the platform. With the development of TIANDITU, topographical hill shading map production for providing and updating global terrain map on line becomes necessary for the characters of strong intuition, three-dimensional sense and aesthetic effect. As such, the terrain service of TIANDITU focuses on displaying the different scales of topographical data globally. And this paper mainly aims to research the method of topographical hill shading map production globally using DEM (Digital Elevation Model) data between the displaying scales about 1 : 140,000,000 to 1 : 4,000,000, corresponded the display level from 2 to 7 on TIANDITU website.

Topographical heterogeneity in transparent PVA hydrogels studied by AFM

Energy Technology Data Exchange (ETDEWEB)

Pramanick, Ashit Kumar; Gupta, Siddhi, E-mail: siddhigupta@nmlindia.org; Mishra, Trilochan; Sinha, Arvind

2012-02-01

Physically crosslinked poly (vinyl alcohol) (PVA) hydrogels have a wide range of biomedical applications. Transparent and stable PVA hydrogels synthesized by freeze-thawing method are potential candidates to be used as tissue engineering scaffolds provided they exhibit suitable topographical roughness and surface energy. The effect of processing parameters i.e., polymer concentration and number of freeze-thaw cycles on the resulting topography of the freeze-thawed transparent hydrogels has been studied and quantified using non-contact mode of an atomic force microscope (AFM) and image analysis. Simultaneously captured phase contrast images have revealed significant information about morphological changes in the topographical features and crystallinity of the hydrogels. Topographical roughness was found to decrease as a function of number of freeze-thaw cycles.

2013 NOAA Topographic Lidar: US Virgin Islands Digital Elevation Models (DEMs)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The United States Virgin Islands Topographic LiDAR Task Order involved collecting and delivering topographic elevation point data derived from multiple return light...

Active airborne contamination control using electrophoresis

International Nuclear Information System (INIS)

Veatch, B.D.

1994-01-01

In spite of our best efforts, radioactive airborne contamination continues to be a formidable problem at many of the Department of Energy (DOE) weapons complex sites. For workers that must enter areas with high levels of airborne contamination, personnel protective equipment (PPE) can become highly restrictive, greatly diminishing productivity. Rather than require even more restrictive PPE for personnel in some situations, the Rocky Flats Plant (RFP) is actively researching and developing methods to aggressively combat airborne contamination hazards using electrophoretic technology. With appropriate equipment, airborne particulates can be effectively removed and collected for disposal in one simple process. The equipment needed to implement electrophoresis is relatively inexpensive, highly reliable, and very compact. Once airborne contamination levels are reduced, less PPE is required and a significant cost savings may be realized through decreased waste and maximized productivity. Preliminary ''cold,'' or non-radioactive, testing results at the RFP have shown the technology to be effective on a reasonable scale, with several potential benefits and an abundance of applications

ZPR-9 airborne plutonium monitoring system

International Nuclear Information System (INIS)

Rusch, G.K.; McDowell, W.P.; Knapp, W.G.

1975-01-01

An airborne plutonium monitoring system which is installed in the ZPR-9 (Zero Power Reactor No. 9) facility at Argonne National Laboratory is described. The design and operational experience are discussed. This monitoring system utilizes particle size and density discrimination, alpha particle energy discrimination, and a background-subtraction techique operating in cascade to separate airborne-plutonium activity from other, naturally occurring, airborne activity. Relatively high sensitivity and reliability are achieved

Software for airborne radiation monitoring system

International Nuclear Information System (INIS)

Sheinfeld, M.; Kadmon, Y.; Tirosh, D.; Elhanany, I.; Gabovitch, A.; Barak, D.

1997-01-01

The Airborne Radiation Monitoring System monitors radioactive contamination in the air or on the ground. The contamination source can be a radioactive plume or an area contaminated with radionuclides. This system is composed of two major parts: Airborne Unit carried by a helicopter, and Ground Station carried by a truck. The Airborne software is intended to be the core of a computerized airborne station. The software is written in C++ under MS-Windows with object-oriented methodology. It has been designed to be user-friendly: function keys and other accelerators are used for vital operations, a help file and help subjects are available, the Human-Machine-Interface is plain and obvious. (authors)

Construction of radioelement and dose rate baseline maps by combining ground and airborne radiometric data

International Nuclear Information System (INIS)

Rybach, L.; Medici, F.; Schwarz, G.F.

1997-01-01

For emergency situations like nuclear accidents, lost isotopic sources, debris of reactor-powered satellites etc. well-documented baseline information is indispensable. Maps of cosmic, terrestrial natural and artificial radiation can be constructed by assembling different datasets such as ground and airborne gamma spectrometry, direct dose rate measurements, and soil/rock samples. The in situ measurements were calibrated using the soil samples taken at/around the field measurement sites, the airborne measurements by a combination of in situ, and soil/rock sample data. The radioelement concentrations (Bq/kg) were in turn converted to dose-rate (nSv/h). First, the cosmic radiation map was constructed from a digital terrain model, averaging topographic heights within cells of 2 km X 2 km size. For the terrestrial radiation a total of 1615 ground data points were available, in addition to the airborne data. The artificial radiation map (Chernobyl and earlier fallout) has the smallest data base (184 data points from airborne and ground measurements). The dose rate map was constructed by summing up the above-mentioned contributions. It relies on a data base which corresponds to a density of about 1 point per 25 km 2 . The cosmic radiation map shows elevated dose rates in the high parts of the Swiss Alps. The cosmic dose rate ranges from 40 to 190 nSv/h, depending on altitude. The terrestrial dose rate maps show general agreement with lithology: elevated dose rates (100 to 200 nSv/h) characterize the Central Massifs of the Alps where crystalline rocks give a maximum of 370 nSv/h, whereas the sedimentary northern Alpine Foreland (Jura, Molasse basin) shows consistently lower dose rates (40-100 nSv/h). The artificial radiation map has its maximum value in the southern part of Switzerland (90 nSv/h). The map of total dose rate exhibits values from 55 to 570 nSv/h. These values are considerably higher than reported in the Radiation Atlas (''Natural Sources of Ionising

Laser-ranging scanning system to observe topographical deformations of volcanoes.

Science.gov (United States)

Aoki, T; Takabe, M; Mizutani, K; Itabe, T

1997-02-20

We have developed a laser-ranging system to observe the topographical structure of volcanoes. This system can be used to measure the distance to a target by a laser and shows the three-dimensional topographical structure of a volcano with an accuracy of 30 cm. This accuracy is greater than that of a typical laser-ranging system that uses a corner-cube reflector as a target because the reflected light jitters as a result of inclination and unevenness of the target ground surface. However, this laser-ranging system is useful for detecting deformations of topographical features in which placement of a reflector is difficult, such as in volcanic regions.

Recent developments in airborne gamma ray surveying

International Nuclear Information System (INIS)

Grasty, Robert L.

1999-01-01

Standardized procedures have been developed for converting airborne gamma ray measurements to ground concentrations of potassium, uranium and thorium. These procedures make use of an airborne calibration range whose ground concentrations should be measured with a calibrated portable spectrometer rather than by taking geochemical samples. Airborne sensitivities and height attenuation coefficients are normally determined from flights over the calibration range but may not be applicable in mountainous areas. Mathematical techniques have been now developed to reduce statistical noise in the airborne measurements by utilizing up to 256 channels of spectral information. (author)

Evaluation of corneal higher order aberrations in normal topographic patterns

Directory of Open Access Journals (Sweden)

Ali Mirzajani

2016-06-01

Conclusions: Based on results in this study, there were a good correlation between corneal topographic pattern and corneal HOAs in normal eyes. These results indicate that the corneal HOAs values are largely determined by the topographic patterns. A larger sample size would perhaps have been beneficial to yield in more accurate outcomes.

a Semi-Empirical Topographic Correction Model for Multi-Source Satellite Images

Science.gov (United States)

Xiao, Sa; Tian, Xinpeng; Liu, Qiang; Wen, Jianguang; Ma, Yushuang; Song, Zhenwei

2018-04-01

Topographic correction of surface reflectance in rugged terrain areas is the prerequisite for the quantitative application of remote sensing in mountainous areas. Physics-based radiative transfer model can be applied to correct the topographic effect and accurately retrieve the reflectance of the slope surface from high quality satellite image such as Landsat8 OLI. However, as more and more images data available from various of sensors, some times we can not get the accurate sensor calibration parameters and atmosphere conditions which are needed in the physics-based topographic correction model. This paper proposed a semi-empirical atmosphere and topographic corrction model for muti-source satellite images without accurate calibration parameters.Based on this model we can get the topographic corrected surface reflectance from DN data, and we tested and verified this model with image data from Chinese satellite HJ and GF. The result shows that the correlation factor was reduced almost 85 % for near infrared bands and the classification overall accuracy of classification increased 14 % after correction for HJ. The reflectance difference of slope face the sun and face away the sun have reduced after correction.

Airborne iodine-125 arising from surface contamination

International Nuclear Information System (INIS)

Kwok, C.S.; Hilditch, T.E.

1982-01-01

Measurements of airborne 125 I were made during the subdivision of 740 MBq stocks of 125 I iodide solution in a hospital dispensary. Within the fume cupboard the mean airborne 125 I concentration was 3.5 +- 2.9 kBqm -3 . No airborne concentration contamination was found outside the fume cupboard during these dispensing sessions. The airborne 125 I concentration arising from deliberate surface contamination (50 μl, 3.7-6.3 MBq) of the top of a lead pot was measured at a height simulating face level at an open work bench. There was a progressive fall in airborne concentration over seven days but even then the level was still significantly above background. Measurements made with the extraction system of the fume cupboard in operation were 2-3 times lower. (U.K.)

Nighttime ionization by energetic particles at Wallops Island in the altitude region 120 to 200 km

Science.gov (United States)

Voss, H. D.; Smith, L. G.

1979-01-01

Five Nike Apache rockets, each including an energetic particle spectrometer and an electron density-electron temperature experiment, have been launched from Wallops Island (L = 2.6) near midnight under varying geomagnetic conditions. On the most recent of these (5 January 1978) an additional spectrometer with a broom magnet, and a 391.4 nm photometer were flown. The data from this flight indicate that the energetic particle flux consists predominantly of protons, neutral hydrogen and possibly other energetic nuclei. The energy spectrum becomes much softer and the flux more intense with increasing Kp for 10-100 keV. The pitch angle distribution at 180 km is asymmetrical with a peak at 90 deg indicating that the majority of particles are near their mirroring altitude. Ionization rates are calculated based on the measured energy spectrum and mirror height distribution. The resulting ionization rate profile is found to be nearly constant with altitude in the region 120 to 200 km. The measured energetic particle flux and calculated ionization rate from the five flights are found to vary with magnetic activity (based on the Kp and Dst indexes) in the same way as the independently derived ionization rates deduced from the electron density profile.

Geological Mapping of Sabah, Malaysia, Using Airborne Gravity Survey

DEFF Research Database (Denmark)

Fauzi Nordin, Ahmad; Jamil, Hassan; Noor Isa, Mohd

2016-01-01

Airborne gravimetry is an effective tool for mapping local gravity fields using a combination of airborne sensors, aircraft and positioning systems. It is suitable for gravity surveys over difficult terrains and areas mixed with land and ocean. This paper describes the geological mapping of Sabah...... using airborne gravity surveys. Airborne gravity data over land areas of Sabah has been combined with the marine airborne gravity data to provide a seamless land-to-sea gravity field coverage in order to produce the geological mapping. Free-air and Bouguer anomaly maps (density 2.67 g/cm3) have been...... derived from the airborne data both as simple ad-hoc plots (at aircraft altitude), and as final plots from the downward continued airborne data, processed as part of the geoids determination. Data are gridded at 0.025 degree spacing which is about 2.7 km and the data resolution of the filtered airborne...

Historic Low Wall Detection via Topographic Parameter Images Derived from Fine-Resolution DEM

Directory of Open Access Journals (Sweden)

Hone-Jay Chu

2017-11-01

Full Text Available Coral walls protect vegetation gardens from strong winds that sweep across Xiji Island, Taiwan Strait for half the year. Topographic parameters based on light detection and ranging (LiDAR-based high-resolution digital elevation model (DEM provide obvious correspondence with the expected form of landscape features. The information on slope, curvature, and openness can help identify the location of landscape features. This study applied the automatic landscape line detection to extract historic vegetable garden wall lines from a LiDAR-derived DEM. The three rapid processes used in this study included the derivation of topographic parameters, line extraction, and aggregation. The rules were extracted from a decision tree to check the line detection from multiple topographic parameters. Results show that wall line detection with multiple topographic parameter images is an alternative means of obtaining essential historic wall feature information. Multiple topographic parameters are highly related to low wall feature identification. Furthermore, the accuracy of wall feature detection is 74% compared with manual interpretation. Thus, this study provides rapid wall detection systems with multiple topographic parameters for further historic landscape management.

A topo-graph model for indistinct target boundary definition from anatomical images.

Science.gov (United States)

Cui, Hui; Wang, Xiuying; Zhou, Jianlong; Gong, Guanzhong; Eberl, Stefan; Yin, Yong; Wang, Lisheng; Feng, Dagan; Fulham, Michael

2018-06-01

It can be challenging to delineate the target object in anatomical imaging when the object boundaries are difficult to discern due to the low contrast or overlapping intensity distributions from adjacent tissues. We propose a topo-graph model to address this issue. The first step is to extract a topographic representation that reflects multiple levels of topographic information in an input image. We then define two types of node connections - nesting branches (NBs) and geodesic edges (GEs). NBs connect nodes corresponding to initial topographic regions and GEs link the nodes at a detailed level. The weights for NBs are defined to measure the similarity of regional appearance, and weights for GEs are defined with geodesic and local constraints. NBs contribute to the separation of topographic regions and the GEs assist the delineation of uncertain boundaries. Final segmentation is achieved by calculating the relevance of the unlabeled nodes to the labels by the optimization of a graph-based energy function. We test our model on 47 low contrast CT studies of patients with non-small cell lung cancer (NSCLC), 10 contrast-enhanced CT liver cases and 50 breast and abdominal ultrasound images. The validation criteria are the Dice's similarity coefficient and the Hausdorff distance. Student's t-test show that our model outperformed the graph models with pixel-only, pixel and regional, neighboring and radial connections (p-values <0.05). Our findings show that the topographic representation and topo-graph model provides improved delineation and separation of objects from adjacent tissues compared to the tested models. Copyright © 2018 Elsevier B.V. All rights reserved.

SGA-WZ: A New Strapdown Airborne Gravimeter

DEFF Research Database (Denmark)

Huang, Yangming; Olesen, Arne Vestergaard; Wu, Meiping

2012-01-01

Inertial navigation systems and gravimeters are now routinely used to map the regional gravitational quantities from an aircraft with mGal accuracy and a spatial resolution of a few kilometers. However, airborne gravimeter of this kind is limited by the inaccuracy of the inertial sensor performance......, the integrated navigation technique and the kinematic acceleration determination. As the GPS technique developed, the vehicle acceleration determination is no longer the limiting factor in airborne gravity due to the cancellation of the common mode acceleration in differential mode. A new airborne gravimeter...... and discussion of the airborne field test results are also given....

EAARL coastal topography-western Florida, post-Hurricane Charley, 2004: seamless (bare earth and submerged.

Science.gov (United States)

Nayegandhi, Amar; Bonisteel, Jamie M.; Wright, C. Wayne; Sallenger, A.H.; Brock, John C.; Yates, Xan

2010-01-01

Project Description These remotely sensed, geographically referenced elevation measurements of lidar-derived seamless (bare-earth and submerged) topography were produced as a collaborative effort between the U.S. Geological Survey (USGS), Coastal and Marine Geology Program (CMGP), St. Petersburg, FL, and the National Aeronautics and Space Administration (NASA), Wallops Flight Facility, VA. This project provides highly detailed and accurate datasets of a portion of the western Florida coastline beachface, acquired post-Hurricane Charley on August 17 and 18, 2004. The datasets are made available for use as a management tool to research scientists and natural-resource managers. An innovative airborne lidar instrument originally developed at the NASA Wallops Flight Facility, and known as the Experimental Advanced Airborne Research Lidar (EAARL), was used during data acquisition. The EAARL system is a raster-scanning, waveform-resolving, green-wavelength (532-nanometer) lidar designed to map near-shore bathymetry, topography, and vegetation structure simultaneously. The EAARL sensor suite includes the raster-scanning, water-penetrating full-waveform adaptive lidar, a down-looking red-green-blue (RGB) digital camera, a high-resolution multispectral color infrared (CIR) camera, two precision dual-frequency kinematic carrier-phase GPS receivers, and an integrated miniature digital inertial measurement unit, which provide for sub-meter georeferencing of each laser sample. The nominal EAARL platform is a twin-engine Cessna 310 aircraft, but the instrument may be deployed on a range of light aircraft. A single pilot, a lidar operator, and a data analyst constitute the crew for most survey operations. This sensor has the potential to make significant contributions in measuring sub-aerial and submarine coastal topography within cross-environmental surveys. Elevation measurements were collected over the survey area using the EAARL system, and the resulting data were then

Topographic stress and catastrophic collapse of volcanic islands

Science.gov (United States)

Moon, S.; Perron, J. T.; Martel, S. J.

2017-12-01

Flank collapse of volcanic islands can devastate coastal environments and potentially induce tsunamis. Previous studies have suggested that factors such as volcanic eruption events, gravitational spreading, the reduction of material strength due to hydrothermal alteration, steep coastal cliffs, or sea level change may contribute to slope instability and induce catastrophic collapse of volcanic flanks. In this study, we examine the potential influence of three-dimensional topographic stress perturbations on flank collapses of volcanic islands. Using a three-dimensional boundary element model, we calculate subsurface stress fields for the Canary and Hawaiian islands to compare the effects of stratovolcano and shield volcano shapes on topographic stresses. Our model accounts for gravitational stresses from the actual shapes of volcanic islands, ambient stress in the underlying plate, and the influence of pore water pressure. We quantify the potential for slope failure of volcanic flanks using a combined model of three-dimensional topographic stress and slope stability. The results of our analysis show that subsurface stress fields vary substantially depending on the shapes of volcanoes, and can influence the size and spatial distribution of flank failures.

Topographic relationships for design rainfalls over Australia

Science.gov (United States)

Johnson, F.; Hutchinson, M. F.; The, C.; Beesley, C.; Green, J.

2016-02-01

Design rainfall statistics are the primary inputs used to assess flood risk across river catchments. These statistics normally take the form of Intensity-Duration-Frequency (IDF) curves that are derived from extreme value probability distributions fitted to observed daily, and sub-daily, rainfall data. The design rainfall relationships are often required for catchments where there are limited rainfall records, particularly catchments in remote areas with high topographic relief and hence some form of interpolation is required to provide estimates in these areas. This paper assesses the topographic dependence of rainfall extremes by using elevation-dependent thin plate smoothing splines to interpolate the mean annual maximum rainfall, for periods from one to seven days, across Australia. The analyses confirm the important impact of topography in explaining the spatial patterns of these extreme rainfall statistics. Continent-wide residual and cross validation statistics are used to demonstrate the 100-fold impact of elevation in relation to horizontal coordinates in explaining the spatial patterns, consistent with previous rainfall scaling studies and observational evidence. The impact of the complexity of the fitted spline surfaces, as defined by the number of knots, and the impact of applying variance stabilising transformations to the data, were also assessed. It was found that a relatively large number of 3570 knots, suitably chosen from 8619 gauge locations, was required to minimise the summary error statistics. Square root and log data transformations were found to deliver marginally superior continent-wide cross validation statistics, in comparison to applying no data transformation, but detailed assessments of residuals in complex high rainfall regions with high topographic relief showed that no data transformation gave superior performance in these regions. These results are consistent with the understanding that in areas with modest topographic relief, as

2011 U.S. Army Corps of Engineers (USACE) Topographic LiDAR: Massachusetts and New Hampshire

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — These files contain classified topographic and bathymetric lidar data as unclassified valid topographic data (1), valid topographic data classified as ground (2),...

TESTING OF LAND COVER CLASSIFICATION FROM MULTISPECTRAL AIRBORNE LASER SCANNING DATA

Directory of Open Access Journals (Sweden)

K. Bakuła

2016-06-01

Full Text Available Multispectral Airborne Laser Scanning provides a new opportunity for airborne data collection. It provides high-density topographic surveying and is also a useful tool for land cover mapping. Use of a minimum of three intensity images from a multiwavelength laser scanner and 3D information included in the digital surface model has the potential for land cover/use classification and a discussion about the application of this type of data in land cover/use mapping has recently begun. In the test study, three laser reflectance intensity images (orthogonalized point cloud acquired in green, near-infrared and short-wave infrared bands, together with a digital surface model, were used in land cover/use classification where six classes were distinguished: water, sand and gravel, concrete and asphalt, low vegetation, trees and buildings. In the tested methods, different approaches for classification were applied: spectral (based only on laser reflectance intensity images, spectral with elevation data as additional input data, and spectro-textural, using morphological granulometry as a method of texture analysis of both types of data: spectral images and the digital surface model. The method of generating the intensity raster was also tested in the experiment. Reference data were created based on visual interpretation of ALS data and traditional optical aerial and satellite images. The results have shown that multispectral ALS data are unlike typical multispectral optical images, and they have a major potential for land cover/use classification. An overall accuracy of classification over 90% was achieved. The fusion of multi-wavelength laser intensity images and elevation data, with the additional use of textural information derived from granulometric analysis of images, helped to improve the accuracy of classification significantly. The method of interpolation for the intensity raster was not very helpful, and using intensity rasters with both first and

Airborne measurements of CO2 column concentrations made with a pulsed IPDA lidar using a multiple-wavelength-locked laser and HgCdTe APD detector

Science.gov (United States)

Abshire, James B.; Ramanathan, Anand K.; Riris, Haris; Allan, Graham R.; Sun, Xiaoli; Hasselbrack, William E.; Mao, Jianping; Wu, Stewart; Chen, Jeffrey; Numata, Kenji; Kawa, Stephan R.; Yang, Mei Ying Melissa; DiGangi, Joshua

2018-04-01

Here we report on measurements made with an improved CO2 Sounder lidar during the ASCENDS 2014 and 2016 airborne campaigns. The changes made to the 2011 version of the lidar included incorporating a rapidly wavelength-tunable, step-locked seed laser in the transmitter, using a much more sensitive HgCdTe APD detector and using an analog digitizer with faster readout time in the receiver. We also improved the lidar's calibration approach and the XCO2 retrieval algorithm. The 2014 and 2016 flights were made over several types of topographic surfaces from 3 to 12 km aircraft altitudes in the continental US. The results are compared to the XCO2 values computed from an airborne in situ sensor during spiral-down maneuvers. The 2014 results show significantly better performance and include measurement of horizontal gradients in XCO2 made over the Midwestern US that agree with chemistry transport models. The results from the 2016 airborne lidar retrievals show precisions of ˜ 0.7 parts per million (ppm) with 1 s averaging over desert surfaces, which is an improvement of about 8 times compared to similar measurements made in 2011. Measurements in 2016 were also made over fresh snow surfaces that have lower surface reflectance at the laser wavelengths. The results from both campaigns showed that the mean values of XCO2 retrieved from the lidar consistently agreed with those based on the in situ sensor to within 1 ppm. The improved precision and accuracy demonstrated in the 2014 and 2016 flights should benefit future airborne science campaigns and advance the technique's readiness for a space-based instrument.

Challenges and Opportunities of Airborne Metagenomics

KAUST Repository

Behzad, H.

2015-05-06

Recent metagenomic studies of environments, such as marine and soil, have significantly enhanced our understanding of the diverse microbial communities living in these habitats and their essential roles in sustaining vast ecosystems. The increase in the number of publications related to soil and marine metagenomics is in sharp contrast to those of air, yet airborne microbes are thought to have significant impacts on many aspects of our lives from their potential roles in atmospheric events such as cloud formation, precipitation, and atmospheric chemistry to their major impact on human health. In this review, we will discuss the current progress in airborne metagenomics, with a special focus on exploring the challenges and opportunities of undertaking such studies. The main challenges of conducting metagenomic studies of airborne microbes are as follows: 1) Low density of microorganisms in the air, 2) efficient retrieval of microorganisms from the air, 3) variability in airborne microbial community composition, 4) the lack of standardized protocols and methodologies, and 5) DNA sequencing and bioinformatics-related challenges. Overcoming these challenges could provide the groundwork for comprehensive analysis of airborne microbes and their potential impact on the atmosphere, global climate, and our health. Metagenomic studies offer a unique opportunity to examine viral and bacterial diversity in the air and monitor their spread locally or across the globe, including threats from pathogenic microorganisms. Airborne metagenomic studies could also lead to discoveries of novel genes and metabolic pathways relevant to meteorological and industrial applications, environmental bioremediation, and biogeochemical cycles.

Airborne gravimetry for geoid and GOCE

DEFF Research Database (Denmark)

Forsberg, R.; Olesen, A. V.; Nielsen, E.

2014-01-01

DTU-Space has since 1996 carried out large area airborne surveys over both polar, tropical and temperate regions, especially for geoid determination and global geopotential models. Recently we have started flying two gravimeters (LCR and Chekan-AM) side by side for increased reliability and redun......DTU-Space has since 1996 carried out large area airborne surveys over both polar, tropical and temperate regions, especially for geoid determination and global geopotential models. Recently we have started flying two gravimeters (LCR and Chekan-AM) side by side for increased reliability...... in Antarctica and Tanzania based on DTU-Space aerogravity and GOCE. In both cases the airborne data validate GOCE to very high degrees, and confirms the synergy of airborne gravity and GOCE. For Antarctica, the deep interior Antarctic survey (continued in 2013 from a remote field camp), shows...... that it is possible efficiently to cover even the most remote regions on the planet with good aerogravity. With the recent termination of the GOCE mission, it is therefore timely to initiate a coordinated, preferably international, airborne gravity effort to cover the polar gap south of 83° S; such a survey can...

A Decade of High-Resolution Arctic Sea Ice Measurements from Airborne Altimetry

Science.gov (United States)

Duncan, K.; Farrell, S. L.; Connor, L. N.; Jackson, C.; Richter-Menge, J.

2017-12-01

Satellite altimeters carried on board ERS-1,-2, EnviSat, ICESat, CryoSat-2, AltiKa and Sentinel-3 have transformed our ability to map the thickness and volume of the polar sea ice cover, on seasonal and decadal time-scales. The era of polar satellite altimetry has coincided with a rapid decline of the Arctic ice cover, which has thinned, and transitioned from a predominantly multi-year to first-year ice cover. In conjunction with basin-scale satellite altimeter observations, airborne surveys of the Arctic Ocean at the end of winter are now routine. These surveys have been targeted to monitor regions of rapid change, and are designed to obtain the full snow and ice thickness distribution, across a range of ice types. Sensors routinely deployed as part of NASA's Operation IceBridge (OIB) campaigns include the Airborne Topographic Mapper (ATM) laser altimeter, the frequency-modulated continuous-wave snow radar, and the Digital Mapping System (DMS). Airborne measurements yield high-resolution data products and thus present a unique opportunity to assess the quality and characteristics of the satellite observations. We present a suite of sea ice data products that describe the snow depth and thickness of the Arctic ice cover during the last decade. Fields were derived from OIB measurements collected between 2009-2017, and from reprocessed data collected during ad-hoc sea ice campaigns prior to OIB. Our bespoke algorithms are designed to accommodate the heterogeneous sea ice surface topography, that varies at short spatial scales. We assess regional and inter-annual variability in the sea ice thickness distribution. Results are compared to satellite-derived ice thickness fields to highlight the sensitivities of satellite footprints to the tails of the thickness distribution. We also show changes in the dynamic forcing shaping the ice pack over the last eight years through an analysis of pressure-ridge sail-height distributions and surface roughness conditions

Hydrographic & Topographic LIDAR Acquisition, Northwest Coast, Washington State - Bathymetric Survey Data

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — These data were collected by the SHOALS-1000T(Scanning Hydrographic Operational Airborne Lidar Survey)system which consists of an airborne laser transmitter/receiver...

Monitoring of airborne bacteria and aerosols in different wards of hospitals - Particle counting usefulness in investigation of airborne bacteria.

Science.gov (United States)

Mirhoseini, Seyed Hamed; Nikaeen, Mahnaz; Khanahmd, Hossein; Hatamzadeh, Maryam; Hassanzadeh, Akbar

2015-01-01

The presence of airborne bacteria in hospital environments is of great concern because of their potential role as a source of hospital-acquired infections (HAI). The aim of this study was the determination and comparison of the concentration of airborne bacteria in different wards of four educational hospitals, and evaluation of whether particle counting could be predictive of airborne bacterial concentration in different wards of a hospital. The study was performed in an operating theatre (OT), intensive care unit (ICU), surgery ward (SW) and internal medicine (IM) ward of four educational hospitals in Isfahan, Iran. A total of 80 samples were analyzed for the presence of airborne bacteria and particle levels. The average level of bacteria ranged from 75-1194 CFU/m (3) . Mean particle levels were higher than class 100,000 cleanrooms in all wards. A significant correlation was observed between the numbers of 1-5 µm particles and levels of airborne bacteria in operating theatres and ICUs. The results showed that factors which may influence the airborne bacterial level in hospital environments should be properly managed to minimize the risk of HAIs especially in operating theaters. Microbial air contamination of hospital settings should be performed by the monitoring of airborne bacteria, but particle counting could be considered as a good operative method for the continuous monitoring of air quality in operating theaters and ICUs where higher risks of infection are suspected.

Airborne Lidar Surface Topography (LIST) Simulator

Science.gov (United States)

Yu, Anthony W.; Krainak, Michael A.; Harding, David J.; Abshire, James B.; Sun, Xiaoli; Cavanaugh, John; Valett, Susan; Ramos-Izquierdo, Luis; Winkert, Tom; Plants, Michael;

Digital airborne camera introduction and technology

CERN Document Server

Sandau, Rainer

2014-01-01

The last decade has seen great innovations on the airborne camera. This book is the first ever written on the topic and describes all components of a digital airborne camera ranging from the object to be imaged to the mass memory device.

ATM Coastal Topography-Texas, 2001: UTM Zone 14

Science.gov (United States)

Klipp, Emily S.; Nayegandhi, Amar; Brock, John C.; Sallenger, A.H.; Bonisteel, Jamie M.; Yates, Xan; Wright, C. Wayne

2009-01-01

These remotely sensed, geographically referenced elevation measurements of lidar-derived first-surface (FS) topography were produced collaboratively by the U.S. Geological Survey (USGS), Florida Integrated Science Center (FISC), St. Petersburg, FL, and the National Aeronautics and Space Administration (NASA), Wallops Flight Facility, VA. This project provides highly detailed and accurate datasets of a portion of the Texas coastline within UTM zone 14, acquired October 12-13, 2001. The datasets are made available for use as a management tool to research scientists and natural-resource managers. An innovative scanning lidar instrument originally developed by NASA, and known as the Airborne Topographic Mapper (ATM), was used during data acquisition. The ATM system is a scanning lidar system that measures high-resolution topography of the land surface and incorporates a green-wavelength laser operating at pulse rates of 2 to 10 kilohertz. Measurements from the laser-ranging device are coupled with data acquired from inertial navigation system (INS) attitude sensors and differentially corrected global positioning system (GPS) receivers to measure topography of the surface at accuracies of +/-15 centimeters. The nominal ATM platform is a Twin Otter or P-3 Orion aircraft, but the instrument may be deployed on a range of light aircraft. Elevation measurements were collected over the survey area using the ATM system, and the resulting data were then processed using the Airborne Lidar Processing System (ALPS), a custom-built processing system developed in a NASA-USGS collaboration. ALPS supports the exploration and processing of lidar data in an interactive or batch mode. Modules for presurvey flight-line definition, flight-path plotting, lidar raster and waveform investigation, and digital camera image playback have been developed. Processing algorithms have been developed to extract the range to the first and last significant return within each waveform. ALPS is used

ATM Coastal Topography-Florida 2001: Eastern Panhandle

Science.gov (United States)

Yates, Xan; Nayegandhi, Amar; Brock, John C.; Sallenger, A.H.; Bonisteel, Jamie M.; Klipp, Emily S.; Wright, C. Wayne

2009-01-01

These remotely sensed, geographically referenced elevation measurements of Lidar-derived first surface (FS) topography were produced collaboratively by the U.S. Geological Survey (USGS), Florida Integrated Science Center (FISC), St. Petersburg, FL, and the National Aeronautics and Space Administration (NASA), Wallops Flight Facility, VA. This project provides highly detailed and accurate datasets of the eastern Florida panhandle coastline, acquired October 2, 2001. The datasets are made available for use as a management tool to research scientists and natural resource managers. An innovative scanning Lidar instrument originally developed by NASA, and known as the Airborne Topographic Mapper (ATM), was used during data acquisition. The ATM system is a scanning Lidar system that measures high-resolution topography of the land surface and incorporates a green-wavelength laser operating at pulse rates of 2 to 10 kilohertz. Measurements from the laser-ranging device are coupled with data acquired from inertial navigation system (INS) attitude sensors and differentially corrected global positioning system (GPS) receivers to measure topography of the surface at accuracies of +/-15 centimeters. The nominal ATM platform is a Twin Otter or P-3 Orion aircraft, but the instrument may be deployed on a range of light aircraft. Elevation measurements were collected over the survey area using the ATM system, and the resulting data were then processed using the Airborne Lidar Processing System (ALPS), a custom-built processing system developed in a NASA-USGS collaboration. ALPS supports the exploration and processing of Lidar data in an interactive or batch mode. Modules for presurvey flight line definition, flight path plotting, Lidar raster and waveform investigation, and digital camera image playback have been developed. Processing algorithms have been developed to extract the range to the first and last significant return within each waveform. ALPS is routinely used to create

ATM Coastal Topography-Mississippi, 2001

Science.gov (United States)

Nayegandhi, Amar; Yates, Xan; Brock, John C.; Sallenger, A.H.; Klipp, Emily S.; Wright, C. Wayne

2009-01-01

These remotely sensed, geographically referenced elevation measurements of lidar-derived first-surface (FS) topography were produced collaboratively by the U.S. Geological Survey (USGS), Florida Integrated Science Center (FISC), St. Petersburg, FL, and the National Aeronautics and Space Administration (NASA), Wallops Flight Facility, VA. This project provides highly detailed and accurate datasets of the Mississippi coastline, from Lakeshore to Petit Bois Island, acquired September 9-10, 2001. The datasets are made available for use as a management tool to research scientists and natural-resource managers. An innovative scanning lidar instrument originally developed by NASA, and known as the Airborne Topographic Mapper (ATM), was used during data acquisition. The ATM system is a scanning lidar system that measures high-resolution topography of the land surface and incorporates a green-wavelength laser operating at pulse rates of 2 to 10 kilohertz. Measurements from the laser-ranging device are coupled with data acquired from inertial navigation system (INS) attitude sensors and differentially corrected global positioning system (GPS) receivers to measure topography of the surface at accuracies of +/-15 centimeters. The nominal ATM platform is a Twin Otter or P-3 Orion aircraft, but the instrument may be deployed on a range of light aircraft. Elevation measurements were collected over the survey area using the ATM system, and the resulting data were then processed using the Airborne Lidar Processing System (ALPS), a custom-built processing system developed in a NASA-USGS collaboration. ALPS supports the exploration and processing of lidar data in an interactive or batch mode. Modules for presurvey flight-line definition, flight-path plotting, lidar raster and waveform investigation, and digital camera image playback have been developed. Processing algorithms have been developed to extract the range to the first and last significant return within each waveform. ALPS

ATM Coastal Topography-Alabama 2001

Science.gov (United States)

Nayegandhi, Amar; Yates, Xan; Brock, John C.; Sallenger, A.H.; Bonisteel, Jamie M.; Klipp, Emily S.; Wright, C. Wayne

2009-01-01

These remotely sensed, geographically referenced elevation measurements of Lidar-derived first surface (FS) topography were produced collaboratively by the U.S. Geological Survey (USGS), Florida Integrated Science Center (FISC), St. Petersburg, FL, and the National Aeronautics and Space Administration (NASA), Wallops Flight Facility, VA. This project provides highly detailed and accurate datasets of the Alabama coastline, acquired October 3-4, 2001. The datasets are made available for use as a management tool to research scientists and natural resource managers. An innovative scanning Lidar instrument originally developed by NASA, and known as the Airborne Topographic Mapper (ATM), was used during data acquisition. The ATM system is a scanning Lidar system that measures high-resolution topography of the land surface, and incorporates a green-wavelength laser operating at pulse rates of 2 to 10 kilohertz. Measurements from the laser ranging device are coupled with data acquired from inertial navigation system (INS) attitude sensors and differentially corrected global positioning system (GPS) receivers to measure topography of the surface at accuracies of +/-15 centimeters. The nominal ATM platform is a Twin Otter or P-3 Orion aircraft, but the instrument may be deployed on a range of light aircraft. Elevation measurements were collected over the survey area using the ATM system, and the resulting data were then processed using the Airborne Lidar Processing System (ALPS), a custom-built processing system developed in a NASA-USGS collaboration. ALPS supports the exploration and processing of Lidar data in an interactive or batch mode. Modules for pre-survey flight line definition, flight path plotting, Lidar raster and waveform investigation, and digital camera image playback have been developed. Processing algorithms have been developed to extract the range to the first and last significant return within each waveform. ALPS is routinely used to create maps that

ATM Coastal Topography-Florida 2001: Western Panhandle

Science.gov (United States)

Yates, Xan; Nayegandhi, Amar; Brock, John C.; Sallenger, A.H.; Bonisteel, Jamie M.; Klipp, Emily S.; Wright, C. Wayne

2009-01-01

These remotely sensed, geographically referenced elevation measurements of Lidar-derived first surface (FS) topography were produced collaboratively by the U.S. Geological Survey (USGS), Florida Integrated Science Center (FISC), St. Petersburg, FL, and the National Aeronautics and Space Administration (NASA), Wallops Flight Facility, VA. This project provides highly detailed and accurate datasets of the western Florida panhandle coastline, acquired October 2-4 and 7-10, 2001. The datasets are made available for use as a management tool to research scientists and natural resource managers. An innovative scanning Lidar instrument originally developed by NASA, and known as the Airborne Topographic Mapper (ATM), was used during data acquisition. The ATM system is a scanning Lidar system that measures high-resolution topography of the land surface and incorporates a green-wavelength laser operating at pulse rates of 2 to 10 kilohertz. Measurements from the laser-ranging device are coupled with data acquired from inertial navigation system (INS) attitude sensors and differentially corrected global positioning system (GPS) receivers to measure topography of the surface at accuracies of +/-15 centimeters. The nominal ATM platform is a Twin Otter or P-3 Orion aircraft, but the instrument may be deployed on a range of light aircraft. Elevation measurements were collected over the survey area using the ATM system, and the resulting data were then processed using the Airborne Lidar Processing System (ALPS), a custom-built processing system developed in a NASA-USGS collaboration. ALPS supports the exploration and processing of Lidar data in an interactive or batch mode. Modules for presurvey flight line definition, flight path plotting, Lidar raster and waveform investigation, and digital camera image playback have been developed. Processing algorithms have been developed to extract the range to the first and last significant return within each waveform. ALPS is routinely used

Assessing biomass accumulation in second growth forests of Puerto Rico using airborne lidar

Science.gov (United States)

Martinuzzi, S.; Cook, B.; Corp, L. A.; Morton, D. C.; Helmer, E.; Keller, M.

2017-12-01

Degraded and second growth tropical forests provide important ecosystem services, such as carbon sequestration and soil stabilization. Lidar data measure the three-dimensional structure of forest canopies and are commonly used to quantify aboveground biomass in temperate forest landscapes. However, the ability of lidar data to quantify second growth forest biomass in complex, tropical landscapes is less understood. Our goal was to evaluate the use of airborne lidar data to quantify aboveground biomass in a complex tropical landscape, the Caribbean island of Puerto Rico. Puerto Rico provides an ideal place for studying biomass accumulation because of the abundance of second growth forests in different stages of recovery, and the high ecological heterogeneity. Puerto Rico was almost entirely deforested for agriculture until the 1930s. Thereafter, agricultural abandonment resulted in a mosaic of second growth forests that have recovered naturally under different types of climate, land use, topography, and soil fertility. We integrated forest plot data from the US Forest Service, Forest Inventory and Analysis (FIA) Program with recent lidar data from NASA Goddard's Lidar, Hyperspectral, and Thermal (G-LiHT) airborne imager to quantify forest biomass across the island's landscape. The G-LiHT data consisted on targeted acquisitions over the FIA plots and other forested areas representing the environmental heterogeneity of the island. To fully assess the potential of the lidar data, we compared the ability of lidar-derived canopy metrics to quantify biomass alone, and in combination with intensity and topographic metrics. The results presented here are a key step for improving our understanding of the patterns and drivers of biomass accumulation in tropical forests.

US Topo: topographic maps for the nation

Science.gov (United States)

Carswell, William J.

2013-01-01

US Topo is the next generation of topographic maps from the U.S. Geological Survey (USGS). Arranged in the familiar 7.5-minute quadrangle format, digital US Topo maps are designed to look and feel (and perform) like the traditional paper topographic maps for which the USGS is so well known. In contrast to paper-based maps, US Topo maps provide modern technical advantages that support faster, wider public distribution and enable basic, on-screen geographic analysis for all users. The US Topo quadrangle map has been redesigned so that map elements are visually distinguishable with the imagery turned on and off, while keeping the file size as small as possible. The US Topo map redesign includes improvements to various display factors, including symbol definitions (color, line thickness, line symbology, area fills), layer order, and annotation fonts. New features for 2013 include the following: a raster shaded relief layer, military boundaries, cemeteries and post offices, and a US Topo cartographic symbols legend as an attachment. US Topo quadrangle maps are available free on the Web. Each map quadrangle is constructed in GeoPDF® format using key layers of geographic data (orthoimagery, roads, geographic names, topographic contours, and hydrographic features) from The National Map databases. US Topo quadrangle maps can be printed from personal computers or plotters as complete, full-sized, maps or in customized sections, in a user-desired specific format. Paper copies of the maps can also be purchased from the USGS Store. Download links and a users guide are featured on the US Topo Web site. US Topo users can turn geographic data layers on and off as needed; they can zoom in and out to highlight specific features or see a broader area. File size for each digital 7.5-minute quadrangle, about 30 megabytes. Associated electronic tools for geographic analysis are available free for download. The US Topo provides the Nation with a topographic product that users can

Large Topographic Rises on Venus: Implications for Mantle Upwelling

Science.gov (United States)

Stofan, Ellen R.; Smrekar, Suzanne E.; Bindschandler, Duane L.; Senske, David A.

1995-01-01

Topographic rises on Venus have been identified that are interpreted to be the surface manifestation of mantle upwellings. These features are classified into groups based on their dominant morphology. Atla and Beta Regiones are classified as rift-dominated, Dione, western Eistla, Bell, and Imdr Regiones as volcano-dominated, and Themis, eastern Eistla, and central Eistla Regiones as corona-dominated. At several topographic rises, geologic indicators were identified that may provide evidence of uplifted topography (e.g., volcanic flow features trending upslope). We assessed the minimum contribution of volcanic construction to the topography of each rise, which in general represents less than 5% of the volume of the rise, similar to the volumes of edifices at terrestrial hotspot swells. The total melt volume at each rise is approximated to be 10(exp 4) - 10(exp 6) cu km. The variations in morphology, topography, and gravity signatures at topographic rises are not interpreted to indicate variations in stage of evolution of a mantle upwelling. Instead, the morphologic variations between the three classes of topographic rises are interpreted to indicate the varying influences of lithospheric structure, plume characteristics, and regional tectonic environment. Within each class, variations in topography, gravity, and amount of volcanism may be indicative of differing stages of evolution. The similarity between swell and volcanic volumes for terrestrial and Venusian hotspots implies comparable time-integrated plume strengths for individual upwellings on the two planets.

Airborne radioactive contamination following aerosol ventilation studies

International Nuclear Information System (INIS)

Mackie, A.; Hart, G.C.; Ibbett, D.A.; Whitehead, R.J.S.

1994-01-01

Lung aerosol ventilation studies may be accompanied by airborne contamination, with subsequent surface contamination. Airborne contamination has been measured prior to, during and following 59 consecutive 99 Tc m -diethylenetriamine pentaacetate (DTPA) aerosol studies using a personal air sampler. Airborne contamination ranging between 0 and 20 330 kBq m -3 has been measured. Airborne contamination increases with degree of patient breathing difficulty. The effective dose equivalent (EDE) to staff from ingested activity has been calculated to be 0.3 μSv per study. This figure is supported by data from gamma camera images of a contaminated staff member. However, surface contamination measurements reveal that 60% of studies exceed maximum permissible contamination limits for the hands; 16% of studies exceed limits for controlled area surfaces. (author)

Applying Topographic Classification, Based on the Hydrological Process, to Design Habitat Linkages for Climate Change

Directory of Open Access Journals (Sweden)

Yongwon Mo

2017-11-01

Full Text Available The use of biodiversity surrogates has been discussed in the context of designing habitat linkages to support the migration of species affected by climate change. Topography has been proposed as a useful surrogate in the coarse-filter approach, as the hydrological process caused by topography such as erosion and accumulation is the basis of ecological processes. However, some studies that have designed topographic linkages as habitat linkages, so far have focused much on the shape of the topography (morphometric topographic classification with little emphasis on the hydrological processes (generic topographic classification to find such topographic linkages. We aimed to understand whether generic classification was valid for designing these linkages. First, we evaluated whether topographic classification is more appropriate for describing actual (coniferous and deciduous and potential (mammals and amphibians habitat distributions. Second, we analyzed the difference in the linkages between the morphometric and generic topographic classifications. The results showed that the generic classification represented the actual distribution of the trees, but neither the morphometric nor the generic classification could represent the potential animal distributions adequately. Our study demonstrated that the topographic classes, according to the generic classification, were arranged successively according to the flow of water, nutrients, and sediment; therefore, it would be advantageous to secure linkages with a width of 1 km or more. In addition, the edge effect would be smaller than with the morphometric classification. Accordingly, we suggest that topographic characteristics, based on the hydrological process, are required to design topographic linkages for climate change.

Idiopathic ophthalmodynia and idiopathic rhinalgia: two topographic facial pain syndromes.

Science.gov (United States)

Pareja, Juan A; Cuadrado, María L; Porta-Etessam, Jesús; Fernández-de-las-Peñas, César; Gili, Pablo; Caminero, Ana B; Cebrián, José L

2010-09-01

To describe 2 topographic facial pain conditions with the pain clearly localized in the eye (idiopathic ophthalmodynia) or in the nose (idiopathic rhinalgia), and to propose their distinction from persistent idiopathic facial pain. Persistent idiopathic facial pain, burning mouth syndrome, atypical odontalgia, and facial arthromyalgia are idiopathic facial pain syndromes that have been separated according to topographical criteria. Still, some other facial pain syndromes might have been veiled under the broad term of persistent idiopathic facial pain. Through a 10-year period we have studied all patients referred to our neurological clinic because of facial pain of unknown etiology that might deviate from all well-characterized facial pain syndromes. In a group of patients we have identified 2 consistent clinical pictures with pain precisely located either in the eye (n=11) or in the nose (n=7). Clinical features resembled those of other localized idiopathic facial syndromes, the key differences relying on the topographic distribution of the pain. Both idiopathic ophthalmodynia and idiopathic rhinalgia seem specific pain syndromes with a distinctive location, and may deserve a nosologic status just as other focal pain syndromes of the face. Whether all such focal syndromes are topographic variants of persistent idiopathic facial pain or independent disorders remains a controversial issue.

Influence of different topographic correction strategies on mountain vegetation classification accuracy in the Lancang Watershed, China

Science.gov (United States)

Zhang, Zhiming; de Wulf, Robert R.; van Coillie, Frieke M. B.; Verbeke, Lieven P. C.; de Clercq, Eva M.; Ou, Xiaokun

2011-01-01

Mapping of vegetation using remote sensing in mountainous areas is considerably hampered by topographic effects on the spectral response pattern. A variety of topographic normalization techniques have been proposed to correct these illumination effects due to topography. The purpose of this study was to compare six different topographic normalization methods (Cosine correction, Minnaert correction, C-correction, Sun-canopy-sensor correction, two-stage topographic normalization, and slope matching technique) for their effectiveness in enhancing vegetation classification in mountainous environments. Since most of the vegetation classes in the rugged terrain of the Lancang Watershed (China) did not feature a normal distribution, artificial neural networks (ANNs) were employed as a classifier. Comparing the ANN classifications, none of the topographic correction methods could significantly improve ETM+ image classification overall accuracy. Nevertheless, at the class level, the accuracy of pine forest could be increased by using topographically corrected images. On the contrary, oak forest and mixed forest accuracies were significantly decreased by using corrected images. The results also showed that none of the topographic normalization strategies was satisfactorily able to correct for the topographic effects in severely shadowed areas.

CALIOPE airborne CO{sub 2} DIAL (CACDI) system design

Energy Technology Data Exchange (ETDEWEB)

Mietz, D.; Archuleta, B.; Archuleta, J. [and others

1997-09-01

Los Alamos National Laboratory is currently developing an airborne CO{sub 2} Differential Absorption Lidar (DIAL) system based on second generation technology demonstrated last summer at NTS. The CALIOPE Airborne CO{sub 2} DIAL (CACDI) system requirements have been compiled based on the mission objectives and SONDIAL model trade studies. Subsystem designs have been developed based on flow down from these system requirements, as well as experience gained from second generation ground tests and N-ABLE (Non-proliferation AirBorne Lidar Experiments) airborne experiments. This paper presents the CACDI mission objectives, system requirements, the current subsystem design, and provides an overview of the airborne experimental plan.

Challenges and opportunities of airborne metagenomics.

Science.gov (United States)

Behzad, Hayedeh; Gojobori, Takashi; Mineta, Katsuhiko

2015-05-06

Recent metagenomic studies of environments, such as marine and soil, have significantly enhanced our understanding of the diverse microbial communities living in these habitats and their essential roles in sustaining vast ecosystems. The increase in the number of publications related to soil and marine metagenomics is in sharp contrast to those of air, yet airborne microbes are thought to have significant impacts on many aspects of our lives from their potential roles in atmospheric events such as cloud formation, precipitation, and atmospheric chemistry to their major impact on human health. In this review, we will discuss the current progress in airborne metagenomics, with a special focus on exploring the challenges and opportunities of undertaking such studies. The main challenges of conducting metagenomic studies of airborne microbes are as follows: 1) Low density of microorganisms in the air, 2) efficient retrieval of microorganisms from the air, 3) variability in airborne microbial community composition, 4) the lack of standardized protocols and methodologies, and 5) DNA sequencing and bioinformatics-related challenges. Overcoming these challenges could provide the groundwork for comprehensive analysis of airborne microbes and their potential impact on the atmosphere, global climate, and our health. Metagenomic studies offer a unique opportunity to examine viral and bacterial diversity in the air and monitor their spread locally or across the globe, including threats from pathogenic microorganisms. Airborne metagenomic studies could also lead to discoveries of novel genes and metabolic pathways relevant to meteorological and industrial applications, environmental bioremediation, and biogeochemical cycles. © The Author(s) 2015. Published by Oxford University Press on behalf of the Society for Molecular Biology and Evolution.

Accuracy assessment of topographic mapping using UAV image integrated with satellite images

International Nuclear Information System (INIS)

Azmi, S M; Ahmad, Baharin; Ahmad, Anuar

2014-01-01

Unmanned Aerial Vehicle or UAV is extensively applied in various fields such as military applications, archaeology, agriculture and scientific research. This study focuses on topographic mapping and map updating. UAV is one of the alternative ways to ease the process of acquiring data with lower operating costs, low manufacturing and operational costs, plus it is easy to operate. Furthermore, UAV images will be integrated with QuickBird images that are used as base maps. The objective of this study is to make accuracy assessment and comparison between topographic mapping using UAV images integrated with aerial photograph and satellite image. The main purpose of using UAV image is as a replacement for cloud covered area which normally exists in aerial photograph and satellite image, and for updating topographic map. Meanwhile, spatial resolution, pixel size, scale, geometric accuracy and correction, image quality and information contents are important requirements needed for the generation of topographic map using these kinds of data. In this study, ground control points (GCPs) and check points (CPs) were established using real time kinematic Global Positioning System (RTK-GPS) technique. There are two types of analysis that are carried out in this study which are quantitative and qualitative assessments. Quantitative assessment is carried out by calculating root mean square error (RMSE). The outputs of this study include topographic map and orthophoto. From this study, the accuracy of UAV image is ± 0.460 m. As conclusion, UAV image has the potential to be used for updating of topographic maps

Spotlight on topographical pressure pain sensitivity maps: a review

Directory of Open Access Journals (Sweden)

Alburquerque-Sendín F

2018-01-01

Full Text Available Francisco Alburquerque-Sendín,1 Pascal Madeleine,2 César Fernández-de-las-Peñas,3 Paula Rezende Camargo,4 Tania Fátima Salvini4 1Department of Socio-Sanitary Sciences, Radiology and Physical Medicine, Universidad de Córdoba, Córdoba, Spain; 2Physical Activity and Human Performance Group, SMI, Department of Health Science and Technology, Faculty of Medicine, Aalborg University, Aalborg, Denmark; 3Department of Physical Therapy, Occupational Therapy, Physical Medicine and Rehabilitation, Universidad Rey Juan Carlos, Madrid, Spain; 4Department of Physical Therapy, Federal University of São Carlos, São Carlos, SP, Brazil Abstract: Mechanical hyperalgesia defined as decreased pressure pain thresholds (PPTs is commonly associated with pain. In this narrative review, we report the current state of the art within topographical pressure sensitivity maps. Such maps are based on multiple PPT assessments. The PPTs are assessed by an a priori defined grid with special focus on both spatial and temporal summation issues. The grid covers the muscle or the body region of interest using absolute or relative values determined from anatomical landmarks or anthropometric values. The collected PPTs are interpolated by Shepard or Franke and Nielson interpolation methods to create topographical pressure sensitivity maps. This new imaging technique has proven to be valuable in various disciplines including exercise physiology, neurology, physical therapy, occupational medicine, oncology, orthopedics, and sport sciences. The reviewed papers have targeted different body regions like the scalp, low back, neck–shoulder, and upper and lower extremities. The maps have delineated spatial heterogeneity in the pressure pain sensitivity underlining the different extents of pressure pain hyperalgesia in both experimentally induced and disease-associated pain conditions. Furthermore, various intervention studies have proven the utility of topographical pressure pain

NASA's Suborbital Missions Teach Engineering and Technology: Goddard Space Flight Center's Wallops Flight Facility

Science.gov (United States)

Winterton, Joyce L.

2016-01-01

A 50 minute-workshop based on NASA publicly available information will be conducted at the International Technology and Engineering Educator Association annual conference. Attendees will include middle and high school teachers and university teacher educators. Engineering and technology are essential to NASA's suborbital missions including sounding rockets, scientific balloon and airborne science. The attendees will learn how to include NASA information on these missions in their teaching.

Extraction of Urban Trees from Integrated Airborne Based Digital Image and LIDAR Point Cloud Datasets - Initial Results

Science.gov (United States)

Dogon-yaro, M. A.; Kumar, P.; Rahman, A. Abdul; Buyuksalih, G.

2016-10-01

Timely and accurate acquisition of information on the condition and structural changes of urban trees serves as a tool for decision makers to better appreciate urban ecosystems and their numerous values which are critical to building up strategies for sustainable development. The conventional techniques used for extracting tree features include; ground surveying and interpretation of the aerial photography. However, these techniques are associated with some constraint, such as labour intensive field work, a lot of financial requirement, influences by weather condition and topographical covers which can be overcome by means of integrated airborne based LiDAR and very high resolution digital image datasets. This study presented a semi-automated approach for extracting urban trees from integrated airborne based LIDAR and multispectral digital image datasets over Istanbul city of Turkey. The above scheme includes detection and extraction of shadow free vegetation features based on spectral properties of digital images using shadow index and NDVI techniques and automated extraction of 3D information about vegetation features from the integrated processing of shadow free vegetation image and LiDAR point cloud datasets. The ability of the developed algorithms shows a promising result as an automated and cost effective approach to estimating and delineated 3D information of urban trees. The research also proved that integrated datasets is a suitable technology and a viable source of information for city managers to be used in urban trees management.

Airborne Evaluation Facility

Data.gov (United States)

Federal Laboratory Consortium — AFRL's Airborne Evaluation Facility (AEF) utilizes Air Force Aero Club resources to conduct test and evaluation of a variety of equipment and concepts. Twin engine...

Quantitative topographic differentiation of the neonatal EEG.

Science.gov (United States)

Paul, Karel; Krajca, Vladimír; Roth, Zdenek; Melichar, Jan; Petránek, Svojmil

2006-09-01

To test the discriminatory topographic potential of a new method of the automatic EEG analysis in neonates. A quantitative description of the neonatal EEG can contribute to the objective assessment of the functional state of the brain, and may improve the precision of diagnosing cerebral dysfunctions manifested by 'disorganization', 'dysrhythmia' or 'dysmaturity'. 21 healthy, full-term newborns were examined polygraphically during sleep (EEG-8 referential derivations, respiration, ECG, EOG, EMG). From each EEG record, two 5-min samples (one from the middle of quiet sleep, the other from the middle of active sleep) were subject to subsequent automatic analysis and were described by 13 variables: spectral features and features describing shape and variability of the signal. The data from individual infants were averaged and the number of variables was reduced by factor analysis. All factors identified by factor analysis were statistically significantly influenced by the location of derivation. A large number of statistically significant differences were also established when comparing the effects of individual derivations on each of the 13 measured variables. Both spectral features and features describing shape and variability of the signal are largely accountable for the topographic differentiation of the neonatal EEG. The presented method of the automatic EEG analysis is capable to assess the topographic characteristics of the neonatal EEG, and it is adequately sensitive and describes the neonatal electroencephalogram with sufficient precision. The discriminatory capability of the used method represents a promise for their application in the clinical practice.

Predictors of Airborne Endotoxin Concentrations in Inner City Homes

Science.gov (United States)

Mazique, D; Diette, GB; Breysse, PN; Matsui, EC; McCormack, MC; Curtin-Brosnan, J; Williams, D; Peng, RD; Hansel, NN

2011-01-01

Few studies have assessed in-home factors which contribute to airborne endotoxin concentrations. In 85 inner-city Baltimore homes, we found no significant correlation between settled dust and airborne endotoxin concentrations. Certain household activities and characteristics, including frequency of dusting, air conditioner use and type of flooring, explained 36–42% of the variability of airborne concentrations. Measurements of both airborne and settled dust endotoxin concentrations may be needed to fully characterize domestic exposure in epidemiologic investigations. PMID:21429483

Representation for dialect recognition using topographic independent component analysis

Science.gov (United States)

Wei, Qu

2004-10-01

In dialect speech recognition, the feature of tone in one dialect is subject to changes in pitch frequency as well as the length of tone. It is beneficial for the recognition if a representation can be derived to account for the frequency and length changes of tone in an effective and meaningful way. In this paper, we propose a method for learning such a representation from a set of unlabeled speech sentences containing the features of the dialect changed from various pitch frequencies and time length. Topographic independent component analysis (TICA) is applied for the unsupervised learning to produce an emergent result that is a topographic matrix made up of basis components. The dialect speech is topographic in the following sense: the basis components as the units of the speech are ordered in the feature matrix such that components of one dialect are grouped in one axis and changes in time windows are accounted for in the other axis. This provides a meaningful set of basis vectors that may be used to construct dialect subspaces for dialect speech recognition.

Identification of invasive and expansive plant species based on airborne hyperspectral and ALS data

Science.gov (United States)

Szporak-Wasilewska, Sylwia; Kuc, Gabriela; Jóźwiak, Jacek; Demarchi, Luca; Chormański, Jarosław; Marcinkowska-Ochtyra, Adriana; Ochtyra, Adrian; Jarocińska, Anna; Sabat, Anita; Zagajewski, Bogdan; Tokarska-Guzik, Barbara; Bzdęga, Katarzyna; Pasierbiński, Andrzej; Fojcik, Barbara; Jędrzejczyk-Korycińska, Monika; Kopeć, Dominik; Wylazłowska, Justyna; Woziwoda, Beata; Michalska-Hejduk, Dorota; Halladin-Dąbrowska, Anna

2017-04-01

The aim of Natura 2000 network is to ensure the long term survival of most valuable and threatened species and habitats in Europe. The encroachment of invasive alien and expansive native plant species is among the most essential threat that can cause significant damage to protected habitats and their biodiversity. The phenomenon requires comprehensive and efficient repeatable solutions that can be applied to various areas in order to assess the impact on habitats. The aim of this study is to investigate of the issue of invasive and expansive plant species as they affect protected areas at a larger scale of Natura 2000 network in Poland. In order to determine the scale of the problem we have been developing methods of identification of invasive and expansive species and then detecting their occurrence and mapping their distribution in selected protected areas within Natura 2000 network using airborne hyperspectral and airborne laser scanning data. The aerial platform used consists of hyperspectral HySpex scanner (451 bands in VNIR and SWIR), Airborne Laser Scanner (FWF) Riegl Lite Mapper and RGB camera. It allowed to obtain simultaneous 1 meter resolution hyperspectral image, 0.1 m resolution orthophotomaps and point cloud data acquired with 7 points/m2. Airborne images were acquired three times per year during growing season to account for plant seasonal change (in May/June, July/August and September/October 2016). The hyperspectral images were radiometrically, geometrically and atmospherically corrected. Atmospheric correction was performed and validated using ASD FieldSpec 4 measurements. ALS point cloud data were used to generate several different topographic, vegetation and intensity products with 1 m spatial resolution. Acquired data (both hyperspectral and ALS) were used to test different classification methods including Mixture Tuned Matched Filtering (MTMF), Spectral Angle Mapper (SAM), Random Forest (RF), Support Vector Machines (SVM), among others

Study on Site Conditions Based on Topographic Slope

Science.gov (United States)

Wu, X.; Wang, X.; Yuan, X.; Chen, M.; Dou, A.

2018-04-01

The travel-time averaged shear-wave velocity to a depth of 30m (Vs30) below the Earth's surface is widely used to classify sites in many building codes. Vs30 is also used to estimate site classification in recent ground-motion prediction equations (GMPEs), and the distribution of Vs30 has been mapped in a region or country. An alternative method has recently been proposed for evaluating global seismic site conditions or Vs30, from the SRTM (Shuttle Radar Topography Mission) DEMs (digital elevation models). The basic premise of the method is that the topographic slope can be used as a reliable proxy for Vs30 in the absence of geologically and geotechnically based site-condition maps through correlations between Vs30 measurements and topographic gradient. Here, we use different resolutions (3 arcsec, 30 arcsec) DEM data to get Vs30 data separately, analyze and compare the difference of Vs30 data and site conditions obtained from different resolution DEM data. Shandong Province in eastern China and Sichuan Province in Western China are studied respectively. It is found that the higher resolution data is better at defining spatial topographic features than the 30c data, but less improvement in its correlation with Vs30.

STUDY ON SITE CONDITIONS BASED ON TOPOGRAPHIC SLOPE

Directory of Open Access Journals (Sweden)

X. Wu

2018-04-01

Full Text Available The travel-time averaged shear-wave velocity to a depth of 30m (Vs30 below the Earth’s surface is widely used to classify sites in many building codes. Vs30 is also used to estimate site classification in recent ground-motion prediction equations (GMPEs, and the distribution of Vs30 has been mapped in a region or country. An alternative method has recently been proposed for evaluating global seismic site conditions or Vs30, from the SRTM (Shuttle Radar Topography Mission DEMs (digital elevation models. The basic premise of the method is that the topographic slope can be used as a reliable proxy for Vs30 in the absence of geologically and geotechnically based site-condition maps through correlations between Vs30 measurements and topographic gradient. Here, we use different resolutions (3 arcsec, 30 arcsec DEM data to get Vs30 data separately, analyze and compare the difference of Vs30 data and site conditions obtained from different resolution DEM data. Shandong Province in eastern China and Sichuan Province in Western China are studied respectively. It is found that the higher resolution data is better at defining spatial topographic features than the 30c data, but less improvement in its correlation with Vs30.

14 CFR 135.175 - Airborne weather radar equipment requirements.

Science.gov (United States)

2010-01-01

... 14 Aeronautics and Space 3 2010-01-01 2010-01-01 false Airborne weather radar equipment... Aircraft and Equipment § 135.175 Airborne weather radar equipment requirements. (a) No person may operate a large, transport category aircraft in passenger-carrying operations unless approved airborne weather...

14 CFR 135.173 - Airborne thunderstorm detection equipment requirements.

Science.gov (United States)

2010-01-01

... 14 Aeronautics and Space 3 2010-01-01 2010-01-01 false Airborne thunderstorm detection equipment... Aircraft and Equipment § 135.173 Airborne thunderstorm detection equipment requirements. (a) No person may... the aircraft is equipped with either approved thunderstorm detection equipment or approved airborne...

Airborne electromagnetic detection of shallow seafloor topographic features, including resolution of multiple sub-parallel seafloor ridges

Science.gov (United States)

Vrbancich, Julian; Boyd, Graham

2014-05-01

The HoistEM helicopter time-domain electromagnetic (TEM) system was flown over waters in Backstairs Passage, South Australia, in 2003 to test the bathymetric accuracy and hence the ability to resolve seafloor structure in shallow and deeper waters (extending to ~40 m depth) that contain interesting seafloor topography. The topography that forms a rock peak (South Page) in the form of a mini-seamount that barely rises above the water surface was accurately delineated along its ridge from the start of its base (where the seafloor is relatively flat) in ~30 m water depth to its peak at the water surface, after an empirical correction was applied to the data to account for imperfect system calibration, consistent with earlier studies using the same HoistEM system. A much smaller submerged feature (Threshold Bank) of ~9 m peak height located in waters of 35 to 40 m depth was also accurately delineated. These observations when checked against known water depths in these two regions showed that the airborne TEM system, following empirical data correction, was effectively operating correctly. The third and most important component of the survey was flown over the Yatala Shoals region that includes a series of sub-parallel seafloor ridges (resembling large sandwaves rising up to ~20 m from the seafloor) that branch out and gradually decrease in height as the ridges spread out across the seafloor. These sub-parallel ridges provide an interesting topography because the interpreted water depths obtained from 1D inversion of TEM data highlight the limitations of the EM footprint size in resolving both the separation between the ridges (which vary up to ~300 m) and the height of individual ridges (which vary up to ~20 m), and possibly also the limitations of assuming a 1D model in areas where the topography is quasi-2D/3D.

Towards airborne nanoparticle mass spectrometry with nanomechanical string resonators

DEFF Research Database (Denmark)

Schmid, Silvan; Kurek, Maksymilian; Boisen, Anja

2013-01-01

airborne nanoparticle sensors. Recently, nanomechanical mass spectrometry was established. One of the biggest challenges of nanomechanical sensors is the low efficiency of diffusion-based sampling. We developed an inertial-based sampling method that enables the efficient sampling of airborne nanoparticles...... mode. Mass spectrometry of airborne nanoparticles requires the simultaneous operation in the first and second mode, which can be implemented in the transduction scheme of the resonator. The presented results lay the cornerstone for the realization of a portable airborne nanoparticle mass spectrometer....

Neah Bay to Cape Alava, Northwest Coast, Washington State - Topographic Survey Data

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — These data were collected by the SHOALS-1000T(Scanning Hydrographic Operational Airborne Lidar Survey)system which consists of an airborne laser transmitter/receiver...

2009 SWFWMD Topographic Lidar: Peace River South (Florida)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — SWFWMD regularly uses digital topographic information to support regulatory, land management and acquisition, planning, engineering and habitat restoration projects....

ASSESSMENT OF THE VOLUNTEERED GEOGRAPHIC INFORMATION FEEDBACK SYSTEM FOR THE DUTCH TOPOGRAPHICAL KEY REGISTER

Directory of Open Access Journals (Sweden)

M. Grus

2015-08-01

Full Text Available Since Topographical Key Register has become an open data the amount of users increased enormously. The highest grow was in the private users group. The increasing number of users and their growing demand for high actuality of the topographic data sets motivates the Dutch Kadaster to innovate and improve the Topographical Key Register (BRT. One of the initiatives was to provide a voluntary geographical information project aiming at providing a user-friendly feedback system adjusted to all kinds of user groups. The feedback system is a compulsory element of the Topographical Key Register in the Netherlands. The Dutch Kadaster is obliged to deliver a feedback system and the key-users are obliged to use it. The aim of the feedback system is to improve the quality and stimulate the usage of the data. The results of the pilot shows that the user-friendly and open to everyone feedback system contributes enormously to improve the quality of the topographic dataset.

14 CFR 125.223 - Airborne weather radar equipment requirements.

Science.gov (United States)

2010-01-01

... 14 Aeronautics and Space 3 2010-01-01 2010-01-01 false Airborne weather radar equipment... Equipment Requirements § 125.223 Airborne weather radar equipment requirements. (a) No person may operate an airplane governed by this part in passenger-carrying operations unless approved airborne weather radar...

14 CFR 121.357 - Airborne weather radar equipment requirements.

Science.gov (United States)

2010-01-01

... 14 Aeronautics and Space 3 2010-01-01 2010-01-01 false Airborne weather radar equipment... § 121.357 Airborne weather radar equipment requirements. (a) No person may operate any transport... December 31, 1964, unless approved airborne weather radar equipment has been installed in the airplane. (b...

ToF-SIMS measurements with topographic information in combined images.

Science.gov (United States)

Koch, Sabrina; Ziegler, Georg; Hutter, Herbert

2013-09-01

In 2D and 3D time-of-flight secondary ion mass spectrometric (ToF-SIMS) analysis, accentuated structures on the sample surface induce distorted element distributions in the measurement. The origin of this effect is the 45° incidence angle of the analysis beam, recording planar images with distortion of the sample surface. For the generation of correct element distributions, these artifacts associated with the sample surface need to be eliminated by measuring the sample surface topography and applying suitable algorithms. For this purpose, the next generation of ToF-SIMS instruments will feature a scanning probe microscope directly implemented in the sample chamber which allows the performance of topography measurements in situ. This work presents the combination of 2D and 3D ToF-SIMS analysis with topographic measurements by ex situ techniques such as atomic force microscopy (AFM), confocal microscopy (CM), and digital holographic microscopy (DHM). The concept of the combination of topographic and ToF-SIMS measurements in a single representation was applied to organic and inorganic samples featuring surface structures in the nanometer and micrometer ranges. The correct representation of planar and distorted ToF-SIMS images was achieved by the combination of topographic data with images of 2D as well as 3D ToF-SIMS measurements, using either AFM, CM, or DHM for the recording of topographic data.

A system for airborne SAR interferometry

DEFF Research Database (Denmark)

Madsen, Søren Nørvang; Skou, Niels; Granholm, Johan

1996-01-01

Interferometric synthetic aperture radar (INSAR) systems have already demonstrated that elevation maps can be generated rapidly with single pass airborne across-track interferometry systems (XTT), and satellite repeat track interferometry (RTT) techniques have been used to map both elevation...... and perturbations of the surface of the Earth. The Danish Center for Remote Sensing (DCRS) has experimented with airborne INSAR since 1993. Multiple track data are collected in a special mode in which the radar directly steers the aircraft which allows for very precise control of the flight path. Such data sets......) the status of the airborne interferometry activities at DCRS, including the present system configuration, recent results, and some scientific applications of the system....

Adaptive topographic mass correction for satellite gravity and gravity gradient data

Science.gov (United States)

Holzrichter, Nils; Szwillus, Wolfgang; Götze, Hans-Jürgen

2014-05-01

Subsurface modelling with gravity data includes a reliable topographic mass correction. Since decades, this mandatory step is a standard procedure. However, originally methods were developed for local terrestrial surveys. Therefore, these methods often include defaults like a limited correction area of 167 km around an observation point, resampling topography depending on the distance to the station or disregard the curvature of the earth. New satellite gravity data (e.g. GOCE) can be used for large scale lithospheric modelling with gravity data. The investigation areas can include thousands of kilometres. In addition, measurements are located in the flight height of the satellite (e.g. ~250 km for GOCE). The standard definition of the correction area and the specific grid spacing around an observation point was not developed for stations located in these heights and areas of these dimensions. This asks for a revaluation of the defaults used for topographic correction. We developed an algorithm which resamples the topography based on an adaptive approach. Instead of resampling topography depending on the distance to the station, the grids will be resampled depending on its influence at the station. Therefore, the only value the user has to define is the desired accuracy of the topographic correction. It is not necessary to define the grid spacing and a limited correction area. Furthermore, the algorithm calculates the topographic mass response with a spherical shaped polyhedral body. We show examples for local and global gravity datasets and compare the results of the topographic mass correction to existing approaches. We provide suggestions how satellite gravity and gradient data should be corrected.

Reduction of Topographic Effect for Curve Number Estimated from Remotely Sensed Imagery

Science.gov (United States)

Zhang, Wen-Yan; Lin, Chao-Yuan

2016-04-01

The Soil Conservation Service Curve Number (SCS-CN) method is commonly used in hydrology to estimate direct runoff volume. The CN is the empirical parameter which corresponding to land use/land cover, hydrologic soil group and antecedent soil moisture condition. In large watersheds with complex topography, satellite remote sensing is the appropriate approach to acquire the land use change information. However, the topographic effect have been usually found in the remotely sensed imageries and resulted in land use classification. This research selected summer and winter scenes of Landsat-5 TM during 2008 to classified land use in Chen-You-Lan Watershed, Taiwan. The b-correction, the empirical topographic correction method, was applied to Landsat-5 TM data. Land use were categorized using K-mean classification into 4 groups i.e. forest, grassland, agriculture and river. Accuracy assessment of image classification was performed with national land use map. The results showed that after topographic correction, the overall accuracy of classification was increased from 68.0% to 74.5%. The average CN estimated from remotely sensed imagery decreased from 48.69 to 45.35 where the average CN estimated from national LULC map was 44.11. Therefore, the topographic correction method was recommended to normalize the topographic effect from the satellite remote sensing data before estimating the CN.

Topographic Beta Spiral and Onshore Intrusion of the Kuroshio Current

Science.gov (United States)

Yang, De-Zhou; Huang, Rui Xin; Yin, Bao-shu; Feng, Xing-Ru; Chen, Hai-ying; Qi, Ji-Feng; Xu, Ling-jing; Shi, Yun-long; Cui, Xuan; Gao, Guan-Dong; Benthuysen, Jessica A.

2018-01-01

The Kuroshio intrusion plays a vitally important role in carrying nutrients to marginal seas. However, the key mechanism leading to the Kuroshio intrusion remains unclear. In this study we postulate a mechanism: when the Kuroshio runs onto steep topography northeast of Taiwan, the strong inertia gives rise to upwelling over topography, leading to a left-hand spiral in the stratified ocean. This is called the topographic beta spiral, which is a major player regulating the Kuroshio intrusion; this spiral can be inferred from hydrographic surveys. In the world oceans, the topographic beta spirals can be induced by upwelling generated by strong currents running onto steep topography. This is a vital mechanism regulating onshore intruding flow and the cross-shelf transport of energy and nutrients from the Kuroshio Current to the East China Sea. This topographic beta spiral reveals a long-term missing link between the oceanic general circulation theory and shelf dynamic theory.

Topographic evolution of a continental indenter: The eastern Southern Alps

Science.gov (United States)

Robl, Jörg; Heberer, Bianca; Prasicek, Günther; Neubauer, Franz; Hergarten, Stefan

2017-04-01

The topographic evolution of the eastern Southern Alps (ESA) is controlled by the Late Oligocene - Early Miocene indentation of the Adriatic microplate into an overthickened orogenic wedge emplaced on top of the European plate. Rivers follow topographic gradients that evolve during continental collision and in turn incise into bedrock counteracting the formation of topography. In principle, erosional surface processes tend to establish a topographic steady state so that an interpretation of topographic metrics in terms of the latest tectonic history should be straightforward. However, a series of complications impede deciphering the topographic record of the ESA. The Pleistocene glaciations locally excavated alpine valleys and perturbed fluvial drainages. The Late Miocene desiccation of the Mediterranean Sea and the uplift of the northern Molasse Basin led to significant base level changes in the far field of the ESA and the Eastern Alps (EA), respectively. Among this multitude of mechanisms, the processes that dominate the current topographic evolution of the ESA and the ESA-EA drainage divide have not been identified and a number of questions regarding the interaction of crustal deformation, erosion and climate in shaping the present-day topography remain. We demonstrate the expected topographic effects of each mechanism in a 1-dimensional model and compare them with observed channel metrics. Modern uplift rates are largely consistent with long-term exhumation in the ESA and with variations in the normalized steepness index (ksn) indicating a stable uplift and erosion pattern since Miocene times. We find that ksn increases with uplift rate and declines from the indenter tip in the northwest to the foreland basin in the southeast. The number and magnitude of knickpoints and the distortion in longitudinal channel profiles similarly decrease towards the east. Most knickpoints probably evolved during Pleistocene glaciation cycles, but may represent the incrementally

Urban forest topographical mapping using UAV LIDAR

Science.gov (United States)

Putut Ash Shidiq, Iqbal; Wibowo, Adi; Kusratmoko, Eko; Indratmoko, Satria; Ardhianto, Ronni; Prasetyo Nugroho, Budi

2017-12-01

Topographical data is highly needed by many parties, such as government institution, mining companies and agricultural sectors. It is not just about the precision, the acquisition time and data processing are also carefully considered. In relation with forest management, a high accuracy topographic map is necessary for planning, close monitoring and evaluating forest changes. One of the solution to quickly and precisely mapped topography is using remote sensing system. In this study, we test high-resolution data using Light Detection and Ranging (LiDAR) collected from unmanned aerial vehicles (UAV) to map topography and differentiate vegetation classes based on height in urban forest area of University of Indonesia (UI). The semi-automatic and manual classifications were applied to divide point clouds into two main classes, namely ground and vegetation. There were 15,806,380 point clouds obtained during the post-process, in which 2.39% of it were detected as ground.

[Relationships between air conditioning, airborne microorganisms and health].

Science.gov (United States)

Parat, S; Perdrix, A; Baconnier, P

1999-01-01

Concurrently with the increase of air-conditioning, potentially severe or frequent new diseases have emerged, giving rise to social and economical consequences. The first part of this work is a state of the art review of the relationships between air-conditioning, airborne microorganisms and health, through a technical, metrological and medical approach. The second part presents four studies performed in this field. Two of them deal with the relationship between airborne microorganisms and technical features of air-conditioning. Measurements performed on actual sites demonstrated the benefit of using high efficiency filters and low risk components in air-conditioning systems. The third study was aimed to look for a relationship between airborne microorganisms and sick building syndrome symptoms. Statistical analyses of individual data revealed significant associations between airborne bacteria or fungi and symptoms. These results may be the first step in determining a dose-response relationship, in order to define threshold limit values in this field. In the fourth study, the contribution of particle counting in assessing exposure to airborne microorganisms was explored by monitoring simultaneous variations of microbial and particle concentrations. The results showed that associating particle counting may allow to detect microbial variations instantaneously, and therefore improve the assessment of exposure to airborne microorganisms.

Characterisation of particulate matter on airborne pollen grains

International Nuclear Information System (INIS)

Ribeiro, Helena; Guimarães, Fernanda; Duque, Laura; Noronha, Fernando; Abreu, Ilda

2015-01-01

A characterization of the physical–chemical composition of the atmospheric PM adsorbed to airborne pollen was performed. Airborne pollen was sampled using a Hirst-type volumetric spore sampler and observed using a Field Emission Electron Probe Microanalyser for PM analysis. A secondary electron image was taken of each pollen grain and EDS spectra were obtained for individually adsorbed particles. All images were analysed and the size parameters of the particles adsorbed to pollen was determined. The measured particles’ equivalent diameter varied between 0.1 and 25.8 μm, mostly in the fine fraction. The dominant particulates identified were Si-rich, Organic-rich, SO-rich, Metals & Oxides and Cl-rich. Significant daily differences were observed in the physical–chemical characteristics of particles adsorbed to the airborne pollen wall. These differences were correlated with weather parameters and atmospheric PM concentration. Airborne pollen has the ability to adsorb fine particles that may enhance its allergenicity. - Highlights: • Airborne pollen sorbs other PM found in suspension. • 84% of the particles sorbed belonged to the fine aerosol fraction. • Adsorbed PM presented daily physical–chemical variations. • Particles sorbed dominated by Si-rich, Organic-rich, SO-rich, Fe-rich and Cl-rich. - Airborne pollen is able to transport finer particulate matter, which presents daily physical–chemical variations.

Airborne laser: a tool to study landscape surface features

International Nuclear Information System (INIS)

Ritchie, J.C.; Jackson, T.J.; Everitt, J.H.; Escobar, D.E.; Murphey, J.B.; Grissinger, E.H.

1992-01-01

Landscape surface features related to erosion and hydrology were measured using an airborne laser profiler. The airborne laser profiler made 4,000 measurements per second with a recording accuracy of 5 cm (1.9 inches) on a single measurement. Digital data from the laser are recorded and analyzed with a personal computer. These airborne laser profiles provide information on surface landscape features. Topography and canopy heights, cover, and distribution of natural vegetation were determined in studies in South Texas. Laser measurements of shrub cover along flightlines were highly correlated (R 2 = 0.98) with ground measurements made with line-intercept methods. Stream channel cross sections on Goodwin Creek in Mississippi were measured quickly and accurately with airborne laser data. Airborne laser profile data were used to measure small gullies in a level fallow field and in field with mature soybeans. While conventional ground-based techniques can be used to make these measurements, airborne laser profiler techniques allow data to be collected quickly, at a high density, and in areas that are essentially inaccessible for ground surveys. Airborne laser profiler data can quantify landscape features related to erosion and runoff, and the laser proler has the potential to be a useful tool for providing other data for studying and managing natural resources

30 CFR 57.5001 - Exposure limits for airborne contaminants.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Exposure limits for airborne contaminants. 57... Underground § 57.5001 Exposure limits for airborne contaminants. Except as permitted by § 57.5005— (a) Except as provided in paragraph (b), the exposure to airborne contaminants shall not exceed, on the basis of...

Characterization of airborne uranium from test firing of XM774 ammunition

International Nuclear Information System (INIS)

Glissmeyer, J.A.; Mishima, J.

1979-11-01

Pacific Northwest Laboratory conducted experiments at Aberdeen Proving Grounds, Maryland, to characterize the airborne depleted uranium (DU) resulting from the test firings of 105-mm, APFSDS-T XM774 ammunition. The goal was to obtain data pertinent to evaluations of human inhalation exposure to the airborne DU. Data was desired concerning the following: (1) size distribution of airborne DU; (2) quantity of airborne DU; (3) dispersion of airborne DU from the target vicinity; (4) amount of DU deposited on the ground; (5) solubility of airborne DU compounds in lung fluid; and (6) oxide forms of airborne and fallout DU. The experiments involved extensive air sampling for total airborne DU particulates and respirable DU particles both above the targets and at distances downwind. Fallout and fragments were collected around the target area. High-speed movies of the smoke generated from the impact of the penetrators were taken to estimate the cloud volumes. Results of the experiments are presented

Airborne Nicotine, Secondhand Smoke, and Precursors to Adolescent Smoking.

Science.gov (United States)

McGrath, Jennifer J; Racicot, Simon; Okoli, Chizimuzo T C; Hammond, S Katharine; O'Loughlin, Jennifer

2018-01-01

Secondhand smoke (SHS) directly increases exposure to airborne nicotine, tobacco's main psychoactive substance. When exposed to SHS, nonsmokers inhale 60% to 80% of airborne nicotine, absorb concentrations similar to those absorbed by smokers, and display high levels of nicotine biomarkers. Social modeling, or observing other smokers, is a well-established predictor of smoking during adolescence. Observing smokers also leads to increased pharmacological exposure to airborne nicotine via SHS. The objective of this study is to investigate whether greater exposure to airborne nicotine via SHS increases the risk for smoking initiation precursors among never-smoking adolescents. Secondary students ( N = 406; never-smokers: n = 338, 53% girls, mean age = 12.9, SD = 0.4) participated in the AdoQuest II longitudinal cohort. They answered questionnaires about social exposure to smoking (parents, siblings, peers) and known smoking precursors (eg, expected benefits and/or costs, SHS aversion, smoking susceptibility, and nicotine dependence symptoms). Saliva and hair samples were collected to derive biomarkers of cotinine and nicotine. Adolescents wore a passive monitor for 1 week to measure airborne nicotine. Higher airborne nicotine was significantly associated with greater expected benefits ( R 2 = 0.024) and lower expected costs ( R 2 = 0.014). Higher social exposure was significantly associated with more temptation to try smoking ( R 2 = 0.025), lower aversion to SHS ( R 2 = 0.038), and greater smoking susceptibility ( R 2 = 0.071). Greater social exposure was significantly associated with more nicotine dependence symptoms; this relation worsened with higher nicotine exposure (cotinine R 2 = 0.096; airborne nicotine R 2 = 0.088). Airborne nicotine exposure via SHS is a plausible risk factor for smoking initiation during adolescence. Public health implications include limiting airborne nicotine through smoking bans in homes and cars, in addition to stringent restrictions

2013 NOAA Topographic Lidar: U.S. Virgin Islands (St. Croix, St. John, St. Thomas)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The United States Virgin Islands Topographic LiDAR project collected topographic elevation point data derived from multiple return light detection and ranging...

A dedicated system for topographical working memory: evidence from domain-specific interference tests.

Science.gov (United States)

Piccardi, L; Nori, R; Boccia, M; Barbetti, S; Verde, P; Guariglia, C; Ferlazzo, F

2015-08-01

In the present study, we used single- and dual-task conditions to investigate the nature of topographical working memory to better understand what type of task can hamper performance during navigation. During dual-task conditions, we considered four different sources of interference: motor (M), spatial motor (SM), verbal (i.e. articulatory suppression AS) and spatial environmental (SE). In order to assess the nature of topographical working memory, we used the Walking Corsi Test, asking the participants to perform two tasks simultaneously (M, SM, AS and SE). Our results showed that only spatial-environmental interference hampers the execution of a topographical working memory task, suggesting a task-domain-specific effect. We also found general gender differences in the topographical working memory capabilities: men were more proficient than women, regardless of the type of interferences. However, like men, women performed worse when a spatial-environmental interference was present.

Alternative analysis of airborne laser data collected within conventional multi-parameter airborne geophysical surveys

Science.gov (United States)

Ahl, Andreas; Supper, R.; Motschka, K.; Schattauer, I.

2010-05-01

For the interpretation of airborne gamma-ray spectrometry as well as airborne electromagnetics it is of great importance to determine the distance between the geophysical sensor and the ground surface. Since radar altimeters do not penetrate vegetation, laser altimeters became popular in airborne geophysics over the past years. Currently the airborne geophysical platform of the Geological Survey of Austria (GBA) is equipped with a Riegl LD90-3800VHS-FLP high resolution laser altimeter, measuring the distances according to the first and the last reflected pulse. The goal of the presented study was to explore the possibilities of deriving additional information about the survey area from the laser data and to determine the accuracy of such results. On one hand the difference between the arrival time of the first and the last reflected pulse can be used to determine the height of the vegetation. This parameter is for example important for the correction of damping effects on airborne gamma-ray measurements caused by vegetation. Moreover especially for groundwater studies at catchment scale, this parameter can also be applied to support the spatial assessment of evapotranspiration. In combination with the altitude above geoid, determined by a GPS receiver, a rough digital elevation model of the survey area can be derived from the laser altimetry. Based on a data set from a survey area in the northern part of Austria, close to the border with the Czech Republic, the reliability of such a digital elevation model and the calculated vegetation height was tested. In this study a mean deviation of -1.4m, with a standard deviation of ±3.4m, between the digital elevation model from Upper Austria (25m spatial resolution) and the determined elevation model was determined. We also found an obvious correlation between the calculated vegetation heights greater 15m and the mapped forest published by the ‘Department of Forest Inventory' of the ‘Federal Forest Office' of Austria

Topographic features over the continental shelf off Visakhapatnam

Digital Repository Service at National Institute of Oceanography (India)

Rao, T.C.S.; Machado, T.; Murthy, K.S.R.

water depth and the continental shelfedge several interesting topographic features such as Terraces, Karstic structures associated with pinnacles and troughs and smooth dome shaped reef structures are recorded. The nature of these features...

Topographic Digital Raster Graphics - USGS DIGITAL RASTER GRAPHICS

Data.gov (United States)

NSGIC Local Govt | GIS Inventory — USGS Topographic Digital Raster Graphics downloaded from LABINS (http://data.labins.org/2003/MappingData/drg/drg_stpl83.cfm). A digital raster graphic (DRG) is a...

Short communication: Multi-scale topographic anisotropy patterns on a Barrier Island

Science.gov (United States)

Houser, Chris; Bishop, Michael; Wernette, Phil

2017-11-01

Barrier islands exhibit a range of landforms that reflect the complex and varied combination of coastal and aeolian processes realized over the evolution of the island. A detailed analysis of the topography can be used to describe the evolution of a barrier island and provide insight on how it may be affected by a change in sea level, storm activity and wind exposure patterns. Topographic anisotropy, or the directional dependence of relief of landforms, can be used to determine the relative importance of different processes to island evolution at a range of scales. This short communication describes the use of scale-dependent topographic anisotropy to characterize the structure of Santa Rosa Island in northwest Florida. Scale-dependent topographic relief and asymmetry were assessed from a LiDAR-derived DEM from May 2004, a few months before the island experienced widespread erosion and overwash during Hurricane Ivan. This application demonstrates how anisotropy can be used to identify unique scale-dependent structures that can be used to interpret the evolution of this barrier island. Results of this preliminary study further highlight the potential of using topographic anisotropy to controls on barrier island response and recovery to storms as well as island resiliency with sea level rise and storm activity.

Enhancement of osteogenesis on micro/nano-topographical carbon fiber-reinforced polyetheretherketone–nanohydroxyapatite biocomposite

Energy Technology Data Exchange (ETDEWEB)

Xu, Anxiu [College of Stomatology, Chongqing Medical University, Chongqing 401147 (China); Chongqing Key Laboratory of Oral Diseases and Biomedical Sciences, Chongqing Medical University, Chongqing 401147 (China); Liu, Xiaochen [Center for Biomedical Materials and Tissue Engineering, Academy for Advanced Interdisciplinary Studies, Peking University, Beijing 100871 (China); Gao, Xiang; Deng, Feng [College of Stomatology, Chongqing Medical University, Chongqing 401147 (China); Chongqing Key Laboratory of Oral Diseases and Biomedical Sciences, Chongqing Medical University, Chongqing 401147 (China); Deng, Yi, E-mail: 18210357357@163.com [College of Stomatology, Chongqing Medical University, Chongqing 401147 (China); Chongqing Key Laboratory of Oral Diseases and Biomedical Sciences, Chongqing Medical University, Chongqing 401147 (China); Wei, Shicheng, E-mail: weishicheng99@163.com [College of Stomatology, Chongqing Medical University, Chongqing 401147 (China); Chongqing Key Laboratory of Oral Diseases and Biomedical Sciences, Chongqing Medical University, Chongqing 401147 (China)

2015-03-01

As an FDA-approved implantable material, carbon fiber-reinforced polyetheretherketone (CFRPEEK) possesses excellent mechanical properties similar to those of human cortical bone and is a prime candidate to replace conventional metallic implants. The bioinertness and inferior osteogenic properties of CFRPEEK, however, limit its clinical application as orthopedic/dental implants. The present work aimed at developing a novel carbon fiber-reinforced polyetheretherketone–nanohydroxyapatite (PEEK/CF/n-HA) ternary biocomposite with micro/nano-topographical surface for the enhancement of the osteogenesis as a potential bioactive material for bone grafting and bone tissue-engineering applications. The combined modification of oxygen plasma and sand-blasting could improve the hydrophily and generate micro/nano-topographical structures on the surface of the CFRPEEK-based ternary biocomposite. The results clearly showcased that the micro-/nano-topographical PEEK/n-HA/CF ternary biocomposite demonstrated the outstanding ability to promote the proliferation and differentiation of MG-63 cells in vitro as well as to boost the osseointegration between implant and bone in vivo, thereby boding well application to bone tissue engineering. - Highlights: • A novel micro/nano-topographical PEEK/n-HA/CF ternary biocomposite was developed. • The modified PEEK biocomposite promotes proliferation and differentiation of cells. • In vivo osseointegration of the micro/nano-topographical PEEK/n-HA/CF was enhanced.

Enhancement of osteogenesis on micro/nano-topographical carbon fiber-reinforced polyetheretherketone–nanohydroxyapatite biocomposite

International Nuclear Information System (INIS)

Xu, Anxiu; Liu, Xiaochen; Gao, Xiang; Deng, Feng; Deng, Yi; Wei, Shicheng

2015-01-01

As an FDA-approved implantable material, carbon fiber-reinforced polyetheretherketone (CFRPEEK) possesses excellent mechanical properties similar to those of human cortical bone and is a prime candidate to replace conventional metallic implants. The bioinertness and inferior osteogenic properties of CFRPEEK, however, limit its clinical application as orthopedic/dental implants. The present work aimed at developing a novel carbon fiber-reinforced polyetheretherketone–nanohydroxyapatite (PEEK/CF/n-HA) ternary biocomposite with micro/nano-topographical surface for the enhancement of the osteogenesis as a potential bioactive material for bone grafting and bone tissue-engineering applications. The combined modification of oxygen plasma and sand-blasting could improve the hydrophily and generate micro/nano-topographical structures on the surface of the CFRPEEK-based ternary biocomposite. The results clearly showcased that the micro-/nano-topographical PEEK/n-HA/CF ternary biocomposite demonstrated the outstanding ability to promote the proliferation and differentiation of MG-63 cells in vitro as well as to boost the osseointegration between implant and bone in vivo, thereby boding well application to bone tissue engineering. - Highlights: • A novel micro/nano-topographical PEEK/n-HA/CF ternary biocomposite was developed. • The modified PEEK biocomposite promotes proliferation and differentiation of cells. • In vivo osseointegration of the micro/nano-topographical PEEK/n-HA/CF was enhanced

Surface forces between rough and topographically structured interfaces

DEFF Research Database (Denmark)

Thormann, Esben

2017-01-01

Within colloidal science, direct or indirect measurements of surface forces represent an important tool for developing a fundamental understanding of colloidal systems, as well as for predictions of the stability of colloidal suspensions. While the general understanding of colloidal interactions...... and manufactured materials, which possess topographical variations. Further, with technological advances in nanotechnology, fabrication of nano- or micro-structured surfaces has become increasingly important for many applications, which calls for a better understanding of the effect of surface topography...... on the interaction between interfaces. This paper presents a review of the current state of understanding of the effect of surface roughness on DLVO forces, as well as on the interactions between topographically structured hydrophobic surfaces in water. While the first case is a natural choice because it represents...

Use of Airborne Hyperspectral Imagery to Map Soil Properties in Tilled Agricultural Fields

International Nuclear Information System (INIS)

Hively, W.D; McCarty, G.W; Reeves, J.B; Lang, M.W; Oesterling, R.A; Delwiche, S.R

2011-01-01

Soil hyperspectral reflectance imagery was obtained for six tilled (soil) agricultural fields using an airborne imaging spectrometer (400-2450 nm, -10 nm resolution, 2.5 m spatial resolution). Surface soil samples (n=315) were analyzed for carbon content, particle size distribution, and 15 agronomically important elements (Mehlich-III extraction). When partial least squares (PLS) regression of imagery-derived reflectance spectra was used to predict analyte concentrations, 13 of the 19 analytes were predicted with R 2 >0.50, including carbon (0.65), aluminum (0.76), iron (0.75), and silt content (0.79). Comparison of 15 spectral math preprocessing treatments showed that a simple first derivative worked well for nearly all analytes. The resulting PLS factors were exported as a vector of coefficients and used to calculate predicted maps of soil properties for each field. Image smoothing with a 3 x 3 low-pass filter prior to spectral data extraction improved prediction accuracy. The resulting raster maps showed variation associated with topographic factors, indicating the effect of soil redistribution and moisture regime on in-field spatial variability. High-resolution maps of soil analyte concentrations can be used to improve precision environmental management of farmlands.

Modeling streamflow from coupled airborne laser scanning and acoustic Doppler current profiler data

Science.gov (United States)

Norris, Lam; Kean, Jason W.; Lyon, Steve

2016-01-01

The rating curve enables the translation of water depth into stream discharge through a reference cross-section. This study investigates coupling national scale airborne laser scanning (ALS) and acoustic Doppler current profiler (ADCP) bathymetric survey data for generating stream rating curves. A digital terrain model was defined from these data and applied in a physically based 1-D hydraulic model to generate rating curves for a regularly monitored location in northern Sweden. Analysis of the ALS data showed that overestimation of the streambank elevation could be adjusted with a root mean square error (RMSE) block adjustment using a higher accuracy manual topographic survey. The results of our study demonstrate that the rating curve generated from the vertically corrected ALS data combined with ADCP data had lower errors (RMSE = 0.79 m3/s) than the empirical rating curve (RMSE = 1.13 m3/s) when compared to streamflow measurements. We consider these findings encouraging as hydrometric agencies can potentially leverage national-scale ALS and ADCP instrumentation to reduce the cost and effort required for maintaining and establishing rating curves at gauging station sites similar to the Röån River.

MorphoTester: An Open Source Application for Morphological Topographic Analysis.

Directory of Open Access Journals (Sweden)

Julia M Winchester

Full Text Available The increased prevalence and affordability of 3D scanning technology is beginning to have significant effects on the research questions and approaches available for studies of morphology. As the current trend of larger and more precise 3D datasets is unlikely to slow in the future, there is a need for efficient and capable tools for high-throughput quantitative analysis of biological shape. The promise and the challenge of implementing relatively automated methods for characterizing surface shape can be seen in the example of dental topographic analysis. Dental topographic analysis comprises a suite of techniques for quantifying tooth surfaces and component features. Topographic techniques have provided insight on mammalian molar form-function relationships and these methods could be applied to address other topics and questions. At the same time implementing multiple complementary topographic methods can have high time and labor costs, and comparability of data formats and approaches is difficult to predict. To address these challenges I present MorphoTester, an open source application for visualizing and quantifying topography from 3D triangulated polygon meshes. This application is Python-based and is free to use. MorphoTester implements three commonly used dental topographic metrics-Dirichlet normal energy, relief index, and orientation patch count rotated (OPCR. Previous OPCR algorithms have used raster-based grid data, which is not directly interchangeable with vector-based triangulated polygon meshes. A 3D-OPCR algorithm is provided here for quantifying complexity from polygon meshes. The efficacy of this metric is tested in a sample of mandibular second molars belonging to four species of cercopithecoid primates. Results suggest that 3D-OPCR is at least as effective for quantifying complexity as previous approaches, and may be more effective due to finer resolution of surface data considered here. MorphoTester represents an advancement

Delineation, characterization, and classification of topographic eminences

Science.gov (United States)

Sinha, Gaurav

Topographic eminences are defined as upwardly rising, convex shaped topographic landforms that are noticeably distinct in their immediate surroundings. As opposed to everyday objects, the properties of a topographic eminence are dependent not only on how it is conceptualized, but is also intrinsically related to its spatial extent and its relative location in the landscape. In this thesis, a system for automated detection, delineation and characterization of topographic eminences based on an analysis of digital elevation models is proposed. Research has shown that conceptualization of eminences (and other landforms) is linked to the cultural and linguistic backgrounds of people. However, the perception of stimuli from our physical environment is not subject to cultural or linguistic bias. Hence, perceptually salient morphological and spatial properties of the natural landscape can form the basis for generically applicable detection and delineation of topographic eminences. Six principles of cognitive eminence modeling are introduced to develop the philosophical foundation of this research regarding eminence delineation and characterization. The first step in delineating eminences is to automatically detect their presence within digital elevation models. This is achieved by the use of quantitative geomorphometric parameters (e.g., elevation, slope and curvature) and qualitative geomorphometric features (e.g., peaks, passes, pits, ridgelines, and valley lines). The process of eminence delineation follows that of eminence detection. It is posited that eminences may be perceived either as monolithic terrain objects, or as composites of morphological parts (e.g., top, bottom, slope). Individual eminences may also simultaneously be conceived as comprising larger, higher order eminence complexes (e.g., mountain ranges). Multiple algorithms are presented for the delineation of simple and complex eminences, and the morphological parts of eminences. The proposed eminence

Automatic 3d Building Model Generations with Airborne LiDAR Data

Science.gov (United States)

Yastikli, N.; Cetin, Z.

2017-11-01

LiDAR systems become more and more popular because of the potential use for obtaining the point clouds of vegetation and man-made objects on the earth surface in an accurate and quick way. Nowadays, these airborne systems have been frequently used in wide range of applications such as DEM/DSM generation, topographic mapping, object extraction, vegetation mapping, 3 dimensional (3D) modelling and simulation, change detection, engineering works, revision of maps, coastal management and bathymetry. The 3D building model generation is the one of the most prominent applications of LiDAR system, which has the major importance for urban planning, illegal construction monitoring, 3D city modelling, environmental simulation, tourism, security, telecommunication and mobile navigation etc. The manual or semi-automatic 3D building model generation is costly and very time-consuming process for these applications. Thus, an approach for automatic 3D building model generation is needed in a simple and quick way for many studies which includes building modelling. In this study, automatic 3D building models generation is aimed with airborne LiDAR data. An approach is proposed for automatic 3D building models generation including the automatic point based classification of raw LiDAR point cloud. The proposed point based classification includes the hierarchical rules, for the automatic production of 3D building models. The detailed analyses for the parameters which used in hierarchical rules have been performed to improve classification results using different test areas identified in the study area. The proposed approach have been tested in the study area which has partly open areas, forest areas and many types of the buildings, in Zekeriyakoy, Istanbul using the TerraScan module of TerraSolid. The 3D building model was generated automatically using the results of the automatic point based classification. The obtained results of this research on study area verified that automatic 3D

AUTOMATIC 3D BUILDING MODEL GENERATIONS WITH AIRBORNE LiDAR DATA

Directory of Open Access Journals (Sweden)

N. Yastikli

2017-11-01

Full Text Available LiDAR systems become more and more popular because of the potential use for obtaining the point clouds of vegetation and man-made objects on the earth surface in an accurate and quick way. Nowadays, these airborne systems have been frequently used in wide range of applications such as DEM/DSM generation, topographic mapping, object extraction, vegetation mapping, 3 dimensional (3D modelling and simulation, change detection, engineering works, revision of maps, coastal management and bathymetry. The 3D building model generation is the one of the most prominent applications of LiDAR system, which has the major importance for urban planning, illegal construction monitoring, 3D city modelling, environmental simulation, tourism, security, telecommunication and mobile navigation etc. The manual or semi-automatic 3D building model generation is costly and very time-consuming process for these applications. Thus, an approach for automatic 3D building model generation is needed in a simple and quick way for many studies which includes building modelling. In this study, automatic 3D building models generation is aimed with airborne LiDAR data. An approach is proposed for automatic 3D building models generation including the automatic point based classification of raw LiDAR point cloud. The proposed point based classification includes the hierarchical rules, for the automatic production of 3D building models. The detailed analyses for the parameters which used in hierarchical rules have been performed to improve classification results using different test areas identified in the study area. The proposed approach have been tested in the study area which has partly open areas, forest areas and many types of the buildings, in Zekeriyakoy, Istanbul using the TerraScan module of TerraSolid. The 3D building model was generated automatically using the results of the automatic point based classification. The obtained results of this research on study area verified

Voxel inversion of airborne EM data

DEFF Research Database (Denmark)

Fiandaca, Gianluca G.; Auken, Esben; Christiansen, Anders Vest C A.V.C.

2013-01-01

We present a geophysical inversion algorithm working directly in a voxel grid disconnected from the actual measuring points, which allows for straightforward integration of different data types in joint inversion, for informing geological/hydrogeological models directly and for easier incorporation...... of prior information. Inversion of geophysical data usually refers to a model space being linked to the actual observation points. For airborne surveys the spatial discretization of the model space reflects the flight lines. Often airborne surveys are carried out in areas where other ground......-based geophysical data are available. The model space of geophysical inversions is usually referred to the positions of the measurements, and ground-based model positions do not generally coincide with the airborne model positions. Consequently, a model space based on the measuring points is not well suited...

Complex Relationships of the Effects of Topographic Characteristics and Susceptible Tree Cover on Burn Severity

Directory of Open Access Journals (Sweden)

Hyun-Joo Lee

2018-01-01

Full Text Available Forest fires and burn severity mosaics have profound impacts on the post-fire dynamics and complexity of forest ecosystems. Numerous studies have investigated the relationship between topographic variables and susceptible tree covers with regard to burn severity. However, these relationships have not been fully elucidated, because most studies have assumed linearity in these relationships. Therefore, we examined the linearity and the nonlinearity in the relationships between topographic variables and susceptible tree covers with burn severity by comparing linear and nonlinear models. The site of the Samcheok fire, the largest recorded forest fire in Korea, was used as the study area. We generated 802 grid cells with a 500-m resolution that encompassed the entire study area and collected a dataset that included the topographic variables and percentage of red pine trees, which are the most susceptible tree cover types in Korea. We used conventional linear models and generalized additive models to estimate the linear and the nonlinear models based on topographic variables and Japanese red pine trees. The results revealed that the percentage of red pine trees had linear effects on burn severity, reinforcing the importance of silviculture and forest management to lower burn severity. Meanwhile, the topographic variables had nonlinear effects on burn severity. Among the topographic variables, elevation had the strongest nonlinear effect on burn severity, possibly by overriding the effects of susceptible fuels over elevation effects or due to the nonlinear effects of topographic characteristics on pre-fire fuel conditions, including the spatial distribution and availability of susceptible tree cover. To validate and generalize the nonlinear effects of elevation and other topographic variables, additional research is required at different fire sites with different tree cover types in different geographic locations.

Data processing of remotely sensed airborne hyperspectral data using the Airborne Processing Library (APL): Geocorrection algorithm descriptions and spatial accuracy assessment

Science.gov (United States)

Warren, Mark A.; Taylor, Benjamin H.; Grant, Michael G.; Shutler, Jamie D.

2014-03-01

Remote sensing airborne hyperspectral data are routinely used for applications including algorithm development for satellite sensors, environmental monitoring and atmospheric studies. Single flight lines of airborne hyperspectral data are often in the region of tens of gigabytes in size. This means that a single aircraft can collect terabytes of remotely sensed hyperspectral data during a single year. Before these data can be used for scientific analyses, they need to be radiometrically calibrated, synchronised with the aircraft's position and attitude and then geocorrected. To enable efficient processing of these large datasets the UK Airborne Research and Survey Facility has recently developed a software suite, the Airborne Processing Library (APL), for processing airborne hyperspectral data acquired from the Specim AISA Eagle and Hawk instruments. The APL toolbox allows users to radiometrically calibrate, geocorrect, reproject and resample airborne data. Each stage of the toolbox outputs data in the common Band Interleaved Lines (BILs) format, which allows its integration with other standard remote sensing software packages. APL was developed to be user-friendly and suitable for use on a workstation PC as well as for the automated processing of the facility; to this end APL can be used under both Windows and Linux environments on a single desktop machine or through a Grid engine. A graphical user interface also exists. In this paper we describe the Airborne Processing Library software, its algorithms and approach. We present example results from using APL with an AISA Eagle sensor and we assess its spatial accuracy using data from multiple flight lines collected during a campaign in 2008 together with in situ surveyed ground control points.

Estimating variability in placido-based topographic systems.

Science.gov (United States)

Kounis, George A; Tsilimbaris, Miltiadis K; Kymionis, George D; Ginis, Harilaos S; Pallikaris, Ioannis G

2007-10-01

To describe a new software tool for the detailed presentation of corneal topography measurements variability by means of color-coded maps. Software was developed in Visual Basic to analyze and process a series of 10 consecutive measurements obtained by a topographic system on calibration spheres, and individuals with emmetropic, low, high, and irregular astigmatic corneas. Corneal surface was segmented into 1200 segments and the coefficient of variance of each segment's keratometric dioptric power was used as the measure of variability. The results were presented graphically in color-coded maps (Variability Maps). Two topographic systems, the TechnoMed C-Scan and the TOMEY Topographic Modeling System (TMS-2N), were examined to demonstrate our method. Graphic representation of coefficient of variance offered a detailed representation of examination variability both in calibration surfaces and human corneas. It was easy to recognize an increase in variability, as the irregularity of examination surfaces increased. In individuals with high and irregular astigmatism, a variability pattern correlated with the pattern of corneal topography: steeper corneal areas possessed higher variability values compared with flatter areas of the same cornea. Numerical data permitted direct comparisons and statistical analysis. We propose a method that permits a detailed evaluation of the variability of corneal topography measurements. The representation of the results both graphically and quantitatively improves interpretability and facilitates a spatial correlation of variability maps with original topography maps. Given the popularity of topography based custom refractive ablations of the cornea, it is possible that variability maps may assist clinicians in the evaluation of corneal topography maps of patients with very irregular corneas, before custom ablation procedures.

State Base Map for GIS – New Digital Topographic Map of the Republic of Macedonia

Directory of Open Access Journals (Sweden)

Zlatko Srbinoski

2009-12-01

Full Text Available The basic aim of the National Spatial Data Infrastructure (NSDI built in accordance with INSPIRE directive is to standardize spatial data infrastructure on national level. In that direction, topographic maps are a basic platform for acquiring spatial data within geoinformation systems and one of the most important  segments of NSDI. This paper presents methodology of establishing the new digital topographic map of the Republic of Macedonia titled “State Base Map for GIS in Macedonia”. This paper analyzes geometrical accuracy of new digital topographic maps. Production of the new digital topographic map has been the most important cartographic project in the Republic of Macedonia since it became independent.

Airborne Gravity: NGS' Airborne Gravity Data for AN01 (2009-2010)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — Airborne gravity data for Alaska collected in 2009-2010 over 2 surveys. This data set is part of the Gravity for the Re-definition of the American Vertical Datum...

30 CFR 57.5005 - Control of exposure to airborne contaminants.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Control of exposure to airborne contaminants... Underground § 57.5005 Control of exposure to airborne contaminants. Control of employee exposure to harmful airborne contaminants shall be, insofar as feasible, by prevention of contamination, removal by exhaust...

Appendix : airborne incidents : an econometric analysis of severity

Science.gov (United States)

2014-12-19

This is the Appendix for Airborne Incidents: An Econometric Analysis of Severity Report. : Airborne loss of separation incidents occur when an aircraft breaches the defined separation limit (vertical and/or horizontal) with another aircraft or terrai...

Networked Airborne Communications Using Adaptive Multi Beam Directional Links

Science.gov (United States)

2016-03-05

Networked Airborne Communications Using Adaptive Multi-Beam Directional Links R. Bruce MacLeod Member, IEEE, and Adam Margetts Member, IEEE MIT...provide new techniques for increasing throughput in airborne adaptive directional net- works. By adaptive directional linking, we mean systems that can...techniques can dramatically increase the capacity in airborne networks. Advances in digital array technology are beginning to put these gains within reach

30 CFR 56.5005 - Control of exposure to airborne contaminants.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Control of exposure to airborne contaminants... Air Quality and Physical Agents Air Quality § 56.5005 Control of exposure to airborne contaminants. Control of employee exposure to harmful airborne contaminants shall be, insofar as feasible, by prevention...

An Improved Physics-Based Model for Topographic Correction of Landsat TM Images

Directory of Open Access Journals (Sweden)

Ainong Li

2015-05-01

Full Text Available Optical remotely sensed images in mountainous areas are subject to radiometric distortions induced by topographic effects, which need to be corrected before quantitative applications. Based on Li model and Sandmeier model, this paper proposed an improved physics-based model for the topographic correction of Landsat Thematic Mapper (TM images. The model employed Normalized Difference Vegetation Index (NDVI thresholds to approximately divide land targets into eleven groups, due to NDVI’s lower sensitivity to topography and its significant role in indicating land cover type. Within each group of terrestrial targets, corresponding MODIS BRDF (Bidirectional Reflectance Distribution Function products were used to account for land surface’s BRDF effect, and topographic effects are corrected without Lambertian assumption. The methodology was tested with two TM scenes of severely rugged mountain areas acquired under different sun elevation angles. Results demonstrated that reflectance of sun-averted slopes was evidently enhanced, and the overall quality of images was improved with topographic effect being effectively suppressed. Correlation coefficients between Near Infra-Red band reflectance and illumination condition reduced almost to zero, and coefficients of variance also showed some reduction. By comparison with the other two physics-based models (Sandmeier model and Li model, the proposed model showed favorable results on two tested Landsat scenes. With the almost half-century accumulation of Landsat data and the successive launch and operation of Landsat 8, the improved model in this paper can be potentially helpful for the topographic correction of Landsat and Landsat-like data.

Dispersion model for airborne particulates inside a building

International Nuclear Information System (INIS)

Perkins, W.C.; Stoddard, D.H.

1985-01-01

An empirical model has been developed for the spread of airborne radioactive particles after they are released inside a building. The model has been useful in performing safety analyses of actinide materials facilities at the Savannah River Plant (SRP). These facilities employ the multiple-air-zone concept; that is, ventilation air flows from rooms or areas of least radioactive material hazard, through zones of increasing hazard, to a treatment system. A composite of the data for dispersion of airborne activity during 12 actual case incidents at SRP forms the basis for this model. These incidents occurred during approximately 90 plant-years of experience at SRP with the chemical and metallurgical processing of purified neptunium and plutonium after their recovery from irradiated uranium. The model gives ratios of the airborne activity concentrations in rooms and corridors near the site of the release. The multiple-air-zone concept has been applied to many designs of nuclear facilities as a safety feature to limit the spread of airborne activity from a release. The model illustrates the limitations of this concept: it predicts an apparently anomalous behavior of airborne particulates; namely, a small migration against the flow of the ventilation air

Interaction of a monopole vortex with an isolated topographic feature in a three-layer geophysical flow

Directory of Open Access Journals (Sweden)

E. A. Ryzhov

2013-02-01

Full Text Available In the frame of a three-layer, quasi-geostrophic analytical model of an f-plane geophysical flow, the Lagrangian advection induced by the interaction of a monopole vortex with an isolated topographic feature is addressed. Two different cases when the monopole is located either within the upper or the middle layer are of our interest. In the bottom layer, there is a delta-function topographic feature, which generates a closed recirculation region in its vicinity due to the background flow. This recirculation region extends to the middle and upper layers, and it plays the role of a topographic vortex. The interaction between the monopole and the topographic vortex causes a complex, including chaotic, advection of fluid particles. We show that the model's parameters, namely the monopole and topographic vortices' strengths and initial positions, and the layers' depths and densities, are responsible for the diverse advection patterns. While the patterns are rather complicated, one can single out two major processes, which mostly govern the fluid particle advection. The first one is the variation in time of the system's phase space structure, so that within the closed region of the topographic vortex, there appear periodically unclosed particle pathways by which the particles leave the topographic vortex. The second one is chaotic advection that arises from the nonstationarity of the monopole–topography interaction.

Advances and perspectives in bathymetry by airborne lidar

Science.gov (United States)

Zhou, Guoqing; Wang, Chenxi; Li, Mingyan; Wang, Yuefeng; Ye, Siqi; Han, Caiyun

2015-12-01

In this paper, the history of the airborne lidar and the development stages of the technology are reviewed. The basic principle of airborne lidar and the method of processing point-cloud data were discussed. At present, single point laser scanning method is widely used in bathymetric survey. Although the method has high ranging accuracy, the data processing and hardware system is too much complicated and expensive. For this reason, this paper present a kind of improved dual-frequency method for bathymetric and sea surface survey, in this method 176 units of 1064nm wavelength laser has been used by push-broom scanning and due to the airborne power limits still use 532nm wavelength single point for bathymetric survey by zigzag scanning. We establish a spatial coordinates for obtaining the WGS-84 of point cloud by using airborne POS system.

Predicting aboveground forest biomass with topographic variables in human-impacted tropical dry forest landscapes

NARCIS (Netherlands)

Salinas-Melgoza, Miguel A.; Skutsch, Margaret; Lovett, Jon C.

2018-01-01

Topographic variables such as slope and elevation partially explain spatial variations in aboveground biomass (AGB) within landscapes. Human activities that impact vegetation, such as cattle grazing and shifting cultivation, often follow topographic features and also play a key role in determining

Unsupervised detection of salt marsh platforms: a topographic method

Science.gov (United States)

Goodwin, Guillaume C. H.; Mudd, Simon M.; Clubb, Fiona J.

2018-03-01

Salt marshes filter pollutants, protect coastlines against storm surges, and sequester carbon, yet are under threat from sea level rise and anthropogenic modification. The sustained existence of the salt marsh ecosystem depends on the topographic evolution of marsh platforms. Quantifying marsh platform topography is vital for improving the management of these valuable landscapes. The determination of platform boundaries currently relies on supervised classification methods requiring near-infrared data to detect vegetation, or demands labour-intensive field surveys and digitisation. We propose a novel, unsupervised method to reproducibly isolate salt marsh scarps and platforms from a digital elevation model (DEM), referred to as Topographic Identification of Platforms (TIP). Field observations and numerical models show that salt marshes mature into subhorizontal platforms delineated by subvertical scarps. Based on this premise, we identify scarps as lines of local maxima on a slope raster, then fill landmasses from the scarps upward, thus isolating mature marsh platforms. We test the TIP method using lidar-derived DEMs from six salt marshes in England with varying tidal ranges and geometries, for which topographic platforms were manually isolated from tidal flats. Agreement between manual and unsupervised classification exceeds 94 % for DEM resolutions of 1 m, with all but one site maintaining an accuracy superior to 90 % for resolutions up to 3 m. For resolutions of 1 m, platforms detected with the TIP method are comparable in surface area to digitised platforms and have similar elevation distributions. We also find that our method allows for the accurate detection of local block failures as small as 3 times the DEM resolution. Detailed inspection reveals that although tidal creeks were digitised as part of the marsh platform, unsupervised classification categorises them as part of the tidal flat, causing an increase in false negatives and overall platform

Unsupervised detection of salt marsh platforms: a topographic method

Directory of Open Access Journals (Sweden)

G. C. H. Goodwin

2018-03-01

Full Text Available Salt marshes filter pollutants, protect coastlines against storm surges, and sequester carbon, yet are under threat from sea level rise and anthropogenic modification. The sustained existence of the salt marsh ecosystem depends on the topographic evolution of marsh platforms. Quantifying marsh platform topography is vital for improving the management of these valuable landscapes. The determination of platform boundaries currently relies on supervised classification methods requiring near-infrared data to detect vegetation, or demands labour-intensive field surveys and digitisation. We propose a novel, unsupervised method to reproducibly isolate salt marsh scarps and platforms from a digital elevation model (DEM, referred to as Topographic Identification of Platforms (TIP. Field observations and numerical models show that salt marshes mature into subhorizontal platforms delineated by subvertical scarps. Based on this premise, we identify scarps as lines of local maxima on a slope raster, then fill landmasses from the scarps upward, thus isolating mature marsh platforms. We test the TIP method using lidar-derived DEMs from six salt marshes in England with varying tidal ranges and geometries, for which topographic platforms were manually isolated from tidal flats. Agreement between manual and unsupervised classification exceeds 94 % for DEM resolutions of 1 m, with all but one site maintaining an accuracy superior to 90 % for resolutions up to 3 m. For resolutions of 1 m, platforms detected with the TIP method are comparable in surface area to digitised platforms and have similar elevation distributions. We also find that our method allows for the accurate detection of local block failures as small as 3 times the DEM resolution. Detailed inspection reveals that although tidal creeks were digitised as part of the marsh platform, unsupervised classification categorises them as part of the tidal flat, causing an increase in false negatives

Inter-agency Working Group for Airborne Data and Telemetry Systems (IWGADTS)

Science.gov (United States)

Webster, Chris; Freudinger, Lawrence; Sorenson, Carl; Myers, Jeff; Sullivan, Don; Oolman, Larry

2009-01-01

The Interagency Coordinating Committee for Airborne Geosciences Research and Applications (ICCAGRA) was established to improve cooperation and communication among agencies sponsoring airborne platforms and instruments for research and applications, and to serve as a resource for senior level management on airborne geosciences issues. The Interagency Working Group for Airborne Data and Telecommunications Systems (IWGADTS) is a subgroup to ICCAGRA for the purpose of developing recommendations leading to increased interoperability among airborne platforms and instrument payloads, producing increased synergy among research programs with similar goals, and enabling the suborbital layer of the Global Earth Observing System of Systems.

Spatiotemporal interpolation of elevation changes derived from satellite altimetry for Jakobshavn Isbræ, Greenland

DEFF Research Database (Denmark)

Hurkmans, R.T.W.L.; Bamber, J.L.; Sørensen, Louise Sandberg

2012-01-01

. In those areas, straightforward interpolation of data is unlikely to reflect the true patterns of dH/dt. Here, four interpolation methods are compared and evaluated over Jakobshavn Isbræ, an outlet glacier for which widespread airborne validation data are available from NASA's Airborne Topographic Mapper...

Rehabilitation in a complex case of topographical disorientation

NARCIS (Netherlands)

Bouwmeester, Lies; van de Wege, Anja; Haaxma, Rob; Snoek, Jos W.

2015-01-01

This paper describes the rehabilitation process of a patient with severe topographical disorientation. The study demonstrates the sustained effects of a tailor-made, meticulous rehabilitation programme based on the gradual development of compensatory strategies. The patient (RB) had a memory

Use of SRTM data to calculate the (RUSLE topographic factor - doi: 10.4025/actascitechnol.v35i3.15792

Directory of Open Access Journals (Sweden)

Paulo Tarso Sanches Oliveira

2013-06-01

Full Text Available The topographic factor of the Universal Soil Loss Equation and its revised version (RUSLE are currently calculated by Digital Elevation Models (DEM integrated to Geographic Information Systems (GIS. However, some countries have no topographic information to calculate DEM. In this study we evaluated the use of the Shuttle Radar Topography Mission (SRTM data for computing the (RUSLE topographic factor. Furthermore, 90 m SRTM DEM, refined 30 m SRTM DEM and DEMs 30 m and 90 m derived from official topographic maps (1:100,000 scale were used. Using DEMs the topographic factor was calculated by USLE-2D software. The topographic factor calculated from SRTM data showed greater detail levels (especially in flat areas than those obtained from topographic maps. The reduction of spatial resolution of DEM-SRTM provided the topographic factor’s average rate decrease. SRTM data may be employed in further studies for soil loss predictions. The methodology may be useful in Brazil for the development of soil and water conservation programs.  

Improved Topographic Normalization for Landsat TM Images by Introducing the MODIS Surface BRDF

Directory of Open Access Journals (Sweden)

Yanli Zhang

2015-05-01

Full Text Available In rugged terrain, the accuracy of surface reflectance estimations is compromised by atmospheric and topographic effects. We propose a new method to simultaneously eliminate atmospheric and terrain effects in Landsat Thematic Mapper (TM images based on a 30 m digital elevation model (DEM and Moderate Resolution Imaging Spectroradiometer (MODIS atmospheric products. Moreover, we define a normalized factor of a Bidirectional Reflectance Distribution Function (BRDF to convert the sloping pixel reflectance into a flat pixel reflectance by using the Ross Thick-Li Sparse BRDF model (Ambrals algorithm and MODIS BRDF/albedo kernel coefficient products. Sole atmospheric correction and topographic normalization were performed for TM images in the upper stream of the Heihe River Basin. The results show that using MODIS atmospheric products can effectively remove atmospheric effects compared with the Fast Line-of-Sight Atmospheric Analysis of Spectral Hypercubes (FLAASH model and the Landsat Climate Data Record (CDR. Moreover, superior topographic effect removal can be achieved by considering the surface BRDF when compared with the surface Lambertian assumption of topographic normalization.

Airborne Test Bed Facility

Data.gov (United States)

Federal Laboratory Consortium — The Laboratory operates the main hangar on the Hanscom Air Force Base flight line. This very large building (~93,000sqft) accommodates the Laboratory's airborne test...

Simulation and Analysis of the Topographic Effects on Snow-Free Albedo over Rugged Terrain

Directory of Open Access Journals (Sweden)

Dalei Hao

2018-02-01

Full Text Available Topography complicates the modeling and retrieval of land surface albedo due to shadow effects and the redistribution of incident radiation. Neglecting topographic effects may lead to a significant bias when estimating land surface albedo over a single slope. However, for rugged terrain, a comprehensive and systematic investigation of topographic effects on land surface albedo is currently ongoing. Accurately estimating topographic effects on land surface albedo over a rugged terrain presents a challenge in remote sensing modeling and applications. In this paper, we focused on the development of a simplified estimation method for snow-free albedo over a rugged terrain at a 1-km scale based on a 30-m fine-scale digital elevation model (DEM. The proposed method was compared with the radiosity approach based on simulated and real DEMs. The results of the comparison showed that the proposed method provided adequate computational efficiency and satisfactory accuracy simultaneously. Then, the topographic effects on snow-free albedo were quantitatively investigated and interpreted by considering the mean slope, subpixel aspect distribution, solar zenith angle, and solar azimuth angle. The results showed that the more rugged the terrain and the larger the solar illumination angle, the more intense the topographic effects were on black-sky albedo (BSA. The maximum absolute deviation (MAD and the maximum relative deviation (MRD of the BSA over a rugged terrain reached 0.28 and 85%, respectively, when the SZA was 60° for different terrains. Topographic effects varied with the mean slope, subpixel aspect distribution, SZA and SAA, which should not be neglected when modeling albedo.

OPTIMIZING THE PAKS METHOD FOR MEASURING AIRBORNE ACROLEIN

Science.gov (United States)

Airborne acrolein is produced from the combustion of fuel and tobacco and is of concern due to its potential for respiratory tract irritation and other adverse health effects. DNPH active-sampling is a method widely used for sampling airborne aldehydes and ketones (carbonyls); ...

Airborne Magnetic Trackline Database

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The NOAA National Centers for Environmental Information (formerly National Geophysical Data Center) receive airborne magnetic survey data from US and non-US...

A first attempt to derive soil erosion rates from 137Cs airborne gamma measurements in two Alpine valleys

Science.gov (United States)

Arata, Laura; Meusburger, Katrin; Bucher, Benno; Mabit, Lionel; Alewell, Christine

2016-04-01

The application of fallout radionuclides (FRNs) as soil tracers is currently one of the most promising and effective approach for evaluating soil erosion magnitudes in mountainous grasslands. Conventional assessment or measurement methods are laborious and constrained by the topographic and climatic conditions of the Alps. The 137Cs (half-life = 30.2 years) is the most frequently used FRN to study soil redistribution. However the application of 137Cs in alpine grasslands is compromised by the high heterogeneity of the fallout due to the origin of 137Cs fallout in the Alps, which is linked to single rain events occurring just after the Chernobyl accident when most of the Alpine soils were still covered by snow. The aim of this study was to improve our understanding of the 137Cs distribution in two study areas in the Central Swiss Alps: the Ursern valley (Canton Uri), and the Piora valley (Canton Ticino). In June 2015, a helicopter equipped with a NaI gamma detector flew over the two study sites and screened the 137Cs activity of the top soil. The use of airborne gamma measurements is particularly efficient in case of higher 137Cs concentration in the soil. Due to their high altitude and high precipitation rates, the Swiss Alps are expected to be more contaminated by 137Cs fallout than other parts of Switzerland. The airborne gamma measurements have been related to several key parameters which characterize the areas, such as soil properties, slopes, expositions and land uses. The ground truthing of the airborne measurements (i.e. the 137Cs laboratory measurements of the soil samples collected at the same points) returned a good fit. The obtained results offer an overview of the 137Cs concentration in the study areas, which allowed us to identify suitable reference sites, and to analyse the relationship between the 137Cs distribution and the above cited parameters. The authors also derived a preliminary qualitative and a quantitative assessment of soil redistribution

77 FR 3323 - Airborne Radar Altimeter Equipment (For Air Carrier Aircraft)

Science.gov (United States)

2012-01-23

... DEPARTMENT OF TRANSPORTATION Federal Aviation Administration Airborne Radar Altimeter Equipment... to cancel Technical Standard Order (TSO)-C67, Airborne Radar Altimeter Equipment (For Air Carrier Aircraft). SUMMARY: This notice announces the FAA's intent to cancel TSO-C67, Airborne Radar Altimeter...

Classification of topographical pattern of spasticity in cerebral palsy: a registry perspective.

Science.gov (United States)

Reid, Susan M; Carlin, John B; Reddihough, Dinah S

2011-01-01

This study used data from a population-based cerebral palsy (CP) registry and systematic review to assess the amount of heterogeneity between registries in topographical patterns when dichotomised into unilateral (USCP) and bilateral spastic CP (BSCP), and whether the terms diplegia and quadriplegia provide useful additional epidemiological information. From the Victorian CP Register, 2956 individuals (1658 males, 1298 females), born 1970-2003, with spastic CP were identified. The proportions with each topographical pattern were analysed overall and by gestational age. Binary logistic regression analysis was used to assess temporal trends. For the review, data were systematically collected on topographical patterns from 27 registries. Estimates of heterogeneity were obtained, overall and by region, reporting period and definition of quadriplegia. Among individuals born <32 weeks, 48% had diplegia, whereas the proportion for children born ≥ 32 weeks was 24% (p < 0.001). Evidence was weak for a temporal trend in the relative proportions of USCP and BSCP (p = 0.038), but much clearer for an increase in the proportion of spastic diplegia relative to quadriplegia (p < 0.001). The review revealed wide variations across studies in the proportion of diplegia (range 34-90%) and BSCP (range 51-86%). These findings argue against a topographical classification based solely on laterality. Copyright © 2011 Elsevier Ltd. All rights reserved.

Determination of Important Topographic Factors for Landslide Mapping Analysis Using MLP Network

Directory of Open Access Journals (Sweden)

Mutasem Sh. Alkhasawneh

2013-01-01

Full Text Available Landslide is one of the natural disasters that occur in Malaysia. Topographic factors such as elevation, slope angle, slope aspect, general curvature, plan curvature, and profile curvature are considered as the main causes of landslides. In order to determine the dominant topographic factors in landslide mapping analysis, a study was conducted and presented in this paper. There are three main stages involved in this study. The first stage is the extraction of extra topographic factors. Previous landslide studies had identified mainly six topographic factors. Seven new additional factors have been proposed in this study. They are longitude curvature, tangential curvature, cross section curvature, surface area, diagonal line length, surface roughness, and rugosity. The second stage is the specification of the weight of each factor using two methods. The methods are multilayer perceptron (MLP network classification accuracy and Zhou's algorithm. At the third stage, the factors with higher weights were used to improve the MLP performance. Out of the thirteen factors, eight factors were considered as important factors, which are surface area, longitude curvature, diagonal length, slope angle, elevation, slope aspect, rugosity, and profile curvature. The classification accuracy of multilayer perceptron neural network has increased by 3% after the elimination of five less important factors.

Three dimensional fuzzy influence analysis of fitting algorithms on integrated chip topographic modeling

International Nuclear Information System (INIS)

Liang, Zhong Wei; Wang, Yi Jun; Ye, Bang Yan; Brauwer, Richard Kars

2012-01-01

In inspecting the detailed performance results of surface precision modeling in different external parameter conditions, the integrated chip surfaces should be evaluated and assessed during topographic spatial modeling processes. The application of surface fitting algorithms exerts a considerable influence on topographic mathematical features. The influence mechanisms caused by different surface fitting algorithms on the integrated chip surface facilitate the quantitative analysis of different external parameter conditions. By extracting the coordinate information from the selected physical control points and using a set of precise spatial coordinate measuring apparatus, several typical surface fitting algorithms are used for constructing micro topographic models with the obtained point cloud. In computing for the newly proposed mathematical features on surface models, we construct the fuzzy evaluating data sequence and present a new three dimensional fuzzy quantitative evaluating method. Through this method, the value variation tendencies of topographic features can be clearly quantified. The fuzzy influence discipline among different surface fitting algorithms, topography spatial features, and the external science parameter conditions can be analyzed quantitatively and in detail. In addition, quantitative analysis can provide final conclusions on the inherent influence mechanism and internal mathematical relation in the performance results of different surface fitting algorithms, topographic spatial features, and their scientific parameter conditions in the case of surface micro modeling. The performance inspection of surface precision modeling will be facilitated and optimized as a new research idea for micro-surface reconstruction that will be monitored in a modeling process

An association between human hippocampal volume and topographical memory in healthy young adults.

Directory of Open Access Journals (Sweden)

Tom eHartley

2012-12-01

Full Text Available The association between human hippocampal structure and topographical memory was investigated in healthy adults (N=30. Structural MR images were acquired, and voxel-based morphometry (VBM was used to estimate local gray matter volume throughout the brain. A complementary automated mesh-based segmentation approach was used to independently isolate and measure specified structures including the hippocampus. Topographical memory was assessed using a version of the Four Mountains Task, a short test designed to target hippocampal spatial function. Each item requires subjects to briefly study a landscape scene before recognizing the depicted place from a novel viewpoint and under altered non-spatial conditions when presented amongst similar alternative scenes. Positive correlations between topographical memory performance and hippocampal volume were observed in both VBM and segmentation-based analyses. Score on the topographical memory task was also correlated with the volume of some subcortical structures, extra-hippocampal gray matter and total brain volume, with the most robust and extensive covariation seen in circumscribed neocortical regions in the insula and anterior temporal lobes. Taken together with earlier findings, the results suggest that global variations in brain morphology affect the volume of the hippocampus and its specific contribution to topographical memory. We speculate that behavioral variation might arise directly through the impact of resource constraints on spatial representations in the hippocampal formation and its inputs, and perhaps indirectly through an increased reliance on non-allocentric strategies.

Three dimensional fuzzy influence analysis of fitting algorithms on integrated chip topographic modeling

Energy Technology Data Exchange (ETDEWEB)

Liang, Zhong Wei; Wang, Yi Jun [Guangzhou Univ., Guangzhou (China); Ye, Bang Yan [South China Univ. of Technology, Guangzhou (China); Brauwer, Richard Kars [Indian Institute of Technology, Kanpur (India)

2012-10-15

In inspecting the detailed performance results of surface precision modeling in different external parameter conditions, the integrated chip surfaces should be evaluated and assessed during topographic spatial modeling processes. The application of surface fitting algorithms exerts a considerable influence on topographic mathematical features. The influence mechanisms caused by different surface fitting algorithms on the integrated chip surface facilitate the quantitative analysis of different external parameter conditions. By extracting the coordinate information from the selected physical control points and using a set of precise spatial coordinate measuring apparatus, several typical surface fitting algorithms are used for constructing micro topographic models with the obtained point cloud. In computing for the newly proposed mathematical features on surface models, we construct the fuzzy evaluating data sequence and present a new three dimensional fuzzy quantitative evaluating method. Through this method, the value variation tendencies of topographic features can be clearly quantified. The fuzzy influence discipline among different surface fitting algorithms, topography spatial features, and the external science parameter conditions can be analyzed quantitatively and in detail. In addition, quantitative analysis can provide final conclusions on the inherent influence mechanism and internal mathematical relation in the performance results of different surface fitting algorithms, topographic spatial features, and their scientific parameter conditions in the case of surface micro modeling. The performance inspection of surface precision modeling will be facilitated and optimized as a new research idea for micro-surface reconstruction that will be monitored in a modeling process.

Detecting geomorphic processes and change with high resolution topographic data

Science.gov (United States)

Mudd, Simon; Hurst, Martin; Grieve, Stuart; Clubb, Fiona; Milodowski, David; Attal, Mikael

2016-04-01

The first global topographic dataset was released in 1996, with 1 km grid spacing. It is astonishing that in only 20 years we now have access to tens of thousands of square kilometres of LiDAR data at point densities greater than 5 points per square meter. This data represents a treasure trove of information that our geomorphic predecessors could only dream of. But what are we to do with this data? Here we explore the potential of high resolution topographic data to dig deeper into geomorphic processes across a wider range of landscapes and using much larger spatial coverage than previously possible. We show how this data can be used to constrain sediment flux relationships using relief and hillslope length, and how this data can be used to detect landscape transience. We show how the nonlinear sediment flux law, proposed for upland, soil mantled landscapes by Roering et al. (1999) is consistent with a number of topographic tests. This flux law allows us to predict how landscapes will respond to tectonic forcing, and we show how these predictions can be used to detect erosion rate perturbations across a range of tectonic settings.

Resuscitation effects of catalase on airborne bacteria.

OpenAIRE

Marthi, B; Shaffer, B T; Lighthart, B; Ganio, L

1991-01-01

Catalase incorporation into enumeration media caused a significant increase (greater than 63%) in the colony-forming abilities of airborne bacteria. Incubation for 30 to 60 min of airborne bacteria in collection fluid containing catalase caused a greater than 95% increase in colony-forming ability. However, catalase did not have any effects on enumeration at high relative humidities (80 to 90%).

High resolution and simultaneous monitoring of airborne radionuclides

International Nuclear Information System (INIS)

Abe, T.; Yamaguchi, Y.; Muguntha Manikandan, N.; Komura, K.

2005-01-01

By using 11 extremely low background Ge detectors at Ogoya Underground Laboratory, it became possible to investigate temporal variations of airborne 212 Pb (T 1/2 =10.6 h) along with 210 Pb and 7 Be with order of magnitude higher time resolution. Then, we have measured airborne nuclides at three monitoring points, (1) roof of our laboratory (LLRL; 40 m ASL), (2) Shinshiku Plateau (640 m ASL) located about 8 km from LLRL as a comparison of vertical distribution, and (3) Hegura Island (10 m ASL) at about 50 km from Wajima located north of Noto Peninsula facing on the Sea of Japan (about 180 km to the north-northeast of LLRL), to investigate influence of Asian continent. Airborne nuclides were collected by high volume air samplers at intervals of a few hours at either two or three points simultaneously. In the same manner, high resolution monitoring was carried out also at the time of passage of typhoon and cold front. In this study, we observed drastic temporal variations of airborne radionuclides and correlations of multiple monitoring points. The results indicate that high resolution and simultaneous monitoring is very useful to understand dynamic state of variations of airborne nuclides due to short and long-term air-mass movement. (author)

Study on analysis from sources of error for Airborne LIDAR

Science.gov (United States)

Ren, H. C.; Yan, Q.; Liu, Z. J.; Zuo, Z. Q.; Xu, Q. Q.; Li, F. F.; Song, C.

2016-11-01

With the advancement of Aerial Photogrammetry, it appears that to obtain geo-spatial information of high spatial and temporal resolution provides a new technical means for Airborne LIDAR measurement techniques, with unique advantages and broad application prospects. Airborne LIDAR is increasingly becoming a new kind of space for earth observation technology, which is mounted by launching platform for aviation, accepting laser pulses to get high-precision, high-density three-dimensional coordinate point cloud data and intensity information. In this paper, we briefly demonstrates Airborne laser radar systems, and that some errors about Airborne LIDAR data sources are analyzed in detail, so the corresponding methods is put forwarded to avoid or eliminate it. Taking into account the practical application of engineering, some recommendations were developed for these designs, which has crucial theoretical and practical significance in Airborne LIDAR data processing fields.

Topographic Anterograde and Retrograde Memory for Spatial ...

African Journals Online (AJOL)

The present study was on the effects of haloperidol injection on anterograde and retrograde topographic memories for spatial behaviours in Long Evan rats. Twelve Long Evan albino rats weighing 0.5 – 0.8 kg (6 males, 6 females) were used for the study. Complex Maze Box of 14 unit T Alley from the Royal Institute of ...

77 FR 21834 - Airborne Radar Altimeter Equipment (For Air Carrier Aircraft)

Science.gov (United States)

2012-04-11

... DEPARTMENT OF TRANSPORTATION Federal Aviation Administration Airborne Radar Altimeter Equipment... Technical Standard Order (TSO)-C67, Airborne Radar Altimeter Equipment (For Air Carrier Aircraft). SUMMARY: This is a confirmation notice of the cancellation of TSO-C67, Airborne Radar Altimeter Equipment (For...

AirborneWind Energy: Airfoil-Airmass Interaction

OpenAIRE

Zanon , Mario; Gros , Sebastien; Meyers , Johan; Diehl , Moritz

2014-01-01

The Airborne Wind Energy paradigm proposes to generate energy by flying a tethered airfoil across the wind flow at a high velocity. While Airborne Wind Energy enables flight in higher-altitude, stronger wind layers, the extra drag generated by the tether motion imposes a significant limit to the overall system efficiency. To address this issue, two airfoils with a shared tether can reduce overall system drag. A study proposed in Zanon et al. (2013) confirms this claim by showing that, in the ...

Airborne plutonium and americium concentrations measured from the top of Rattlesnake Mountain

International Nuclear Information System (INIS)

Sehmel, G.A.

1979-01-01

Airborne plutonium-239+240 and americium-241 blowing from offsite was measured in an initial experiment at the top of Rattlesnake Mountain. Average airborne concentration measured was similar to fallout concentrations. Airborne plutonium concentrations were independent of wind speed for seven wind speed increments between 0.5 and 31 m/sec. In contrast the airborne americium concentration was a minimum at a wind speed of approximately 7 m/sec. Similarly, the airborne solids concentration in μg/m 3 was a minimum at an intermediate wind speed increment of 7 to 11 m/sec

A Visual Framework for Digital Reconstruction of Topographic Maps

KAUST Repository

Thabet, Ali Kassem; Smith, Neil; Wittmann, Roland; Schneider, Jens

2014-01-01

, this method has broad applicability for digitization and reconstruction of the world's old topographic maps that are often the only record of past landscapess and cultural heritage before their destruction under modern development.

SGA-WZ: A New Strapdown Airborne Gravimeter

Directory of Open Access Journals (Sweden)

Kaidong Zhang

2012-07-01

Full Text Available Inertial navigation systems and gravimeters are now routinely used to map the regional gravitational quantities from an aircraft with mGal accuracy and a spatial resolution of a few kilometers. However, airborne gravimeter of this kind is limited by the inaccuracy of the inertial sensor performance, the integrated navigation technique and the kinematic acceleration determination. As the GPS technique developed, the vehicle acceleration determination is no longer the limiting factor in airborne gravity due to the cancellation of the common mode acceleration in differential mode. A new airborne gravimeter taking full advantage of the inertial navigation system is described with improved mechanical design, high precision time synchronization, better thermal control and optimized sensor modeling. Apart from the general usage, the Global Positioning System (GPS after differentiation is integrated to the inertial navigation system which provides not only more precise altitude information along with the navigation aiding, but also an effective way to calculate the vehicle acceleration. Design description and test results on the performance of the gyroscopes and accelerations will be emphasized. Analysis and discussion of the airborne field test results are also given.

Characterization of airborne bacteria at an underground subway station.

Science.gov (United States)

Dybwad, Marius; Granum, Per Einar; Bruheim, Per; Blatny, Janet Martha

2012-03-01

The reliable detection of airborne biological threat agents depends on several factors, including the performance criteria of the detector and its operational environment. One step in improving the detector's performance is to increase our knowledge of the biological aerosol background in potential operational environments. Subway stations are enclosed public environments, which may be regarded as potential targets for incidents involving biological threat agents. In this study, the airborne bacterial community at a subway station in Norway was characterized (concentration level, diversity, and virulence- and survival-associated properties). In addition, a SASS 3100 high-volume air sampler and a matrix-assisted laser desorption ionization-time of flight mass spectrometry-based isolate screening procedure was used for these studies. The daytime level of airborne bacteria at the station was higher than the nighttime and outdoor levels, and the relative bacterial spore number was higher in outdoor air than at the station. The bacterial content, particle concentration, and size distribution were stable within each environment throughout the study (May to September 2010). The majority of the airborne bacteria belonged to the genera Bacillus, Micrococcus, and Staphylococcus, but a total of 37 different genera were identified in the air. These results suggest that anthropogenic sources are major contributors to airborne bacteria at subway stations and that such airborne communities could harbor virulence- and survival-associated properties of potential relevance for biological detection and surveillance, as well as for public health. Our findings also contribute to the development of realistic testing and evaluation schemes for biological detection/surveillance systems by providing information that can be used to mimic real-life operational airborne environments in controlled aerosol test chambers.

Characterization of Airborne Bacteria at an Underground Subway Station

Science.gov (United States)

Dybwad, Marius; Granum, Per Einar; Bruheim, Per

2012-01-01

The reliable detection of airborne biological threat agents depends on several factors, including the performance criteria of the detector and its operational environment. One step in improving the detector's performance is to increase our knowledge of the biological aerosol background in potential operational environments. Subway stations are enclosed public environments, which may be regarded as potential targets for incidents involving biological threat agents. In this study, the airborne bacterial community at a subway station in Norway was characterized (concentration level, diversity, and virulence- and survival-associated properties). In addition, a SASS 3100 high-volume air sampler and a matrix-assisted laser desorption ionization–time of flight mass spectrometry-based isolate screening procedure was used for these studies. The daytime level of airborne bacteria at the station was higher than the nighttime and outdoor levels, and the relative bacterial spore number was higher in outdoor air than at the station. The bacterial content, particle concentration, and size distribution were stable within each environment throughout the study (May to September 2010). The majority of the airborne bacteria belonged to the genera Bacillus, Micrococcus, and Staphylococcus, but a total of 37 different genera were identified in the air. These results suggest that anthropogenic sources are major contributors to airborne bacteria at subway stations and that such airborne communities could harbor virulence- and survival-associated properties of potential relevance for biological detection and surveillance, as well as for public health. Our findings also contribute to the development of realistic testing and evaluation schemes for biological detection/surveillance systems by providing information that can be used to mimic real-life operational airborne environments in controlled aerosol test chambers. PMID:22247150

Airborne Microalgae: Insights, Opportunities, and Challenges

Science.gov (United States)

Skjøth, Carsten Ambelas; Šantl-Temkiv, Tina; Löndahl, Jakob

2016-01-01

Airborne dispersal of microalgae has largely been a blind spot in environmental biological studies because of their low concentration in the atmosphere and the technical limitations in investigating microalgae from air samples. Recent studies show that airborne microalgae can survive air transportation and interact with the environment, possibly influencing their deposition rates. This minireview presents a summary of these studies and traces the possible route, step by step, from established ecosystems to new habitats through air transportation over a variety of geographic scales. Emission, transportation, deposition, and adaptation to atmospheric stress are discussed, as well as the consequences of their dispersal on health and the environment and state-of-the-art techniques to detect and model airborne microalga dispersal. More-detailed studies on the microalga atmospheric cycle, including, for instance, ice nucleation activity and transport simulations, are crucial for improving our understanding of microalga ecology, identifying microalga interactions with the environment, and preventing unwanted contamination events or invasions. PMID:26801574

Estimating continuous floodplain and major river bed topography mixing ordinal coutour lines and topographic points

Science.gov (United States)

Bailly, J. S.; Dartevelle, M.; Delenne, C.; Rousseau, A.

2017-12-01

Floodplain and major river bed topography govern many river biophysical processes during floods. Despite the grow of direct topographic measurements from LiDARS on riverine systems, it still room to develop methods for large (e.g. deltas) or very local (e.g. ponds) riverine systems that take advantage of information coming from simple SAR or optical image processing on floodplain, resulting from waterbodies delineation during flood up or down, and producing ordered coutour lines. The next challenge is thus to exploit such data in order to estimate continuous topography on the floodplain combining heterogeneous data: a topographic points dataset and a located but unknown and ordered contourline dataset. This article is comparing two methods designed to estimate continuous topography on the floodplain mixing ordinal coutour lines and continuous topographic points. For both methods a first estimation step is to value each contourline with elevation and a second step is next to estimate the continuous field from both topographic points and valued contourlines. The first proposed method is a stochastic method starting from multigaussian random-fields and conditional simualtion. The second is a deterministic method based on radial spline fonction for thin layers used for approximated bivariate surface construction. Results are first shown and discussed from a set of synoptic case studies presenting various topographic points density and topographic smoothness. Next, results are shown and discuss on an actual case study in the Montagua laguna, located in the north of Valparaiso, Chile.

Airborne microorganisms from waste containers.

Science.gov (United States)

Jedlicka, Sabrina S; Stravitz, David M; Lyman, Charles E

2012-01-01

In physician's offices and biomedical labs, biological waste is handled every day. This waste is disposed of in waste containers designed for holding red autoclave bags. The containers used in these environments are closed hands-free containers, often with a step pedal. While these containers protect the user from surface-borne microorganisms, the containers may allow airborne microorganisms to escape via the open/close mechanism because of the air current produced upon open/close cycles. In this study, the air current was shown to be sufficient to allow airborne escape of microorganisms held in the container, including Aspergillus niger. However, bacterial cultures, such as Escherichia coli and Lactococcus lactis did not escape. This may be due to the choice of bacterial cultures and the absence of solid waste, such as dust or other particulate matter in the waste containers, that such strains of bacteria could travel on during aerosolization. We compared these results to those obtained using a re-designed receptacle, which mimimizes air currents, and detected no escaping microorganisms. This study highlights one potential source of airborne contamination in labs, hospitals, and other environments that dispose of biological waste.

Inactivation of an enterovirus by airborne disinfectants

Science.gov (United States)

2013-01-01

Background The activity of airborne disinfectants on bacteria, fungi and spores has been reported. However, the issue of the virucidal effect of disinfectants spread by fogging has not been studied thoroughly. Methods A procedure has been developed to determine the virucidal activity of peracetic acid-based airborne disinfectants on a resistant non-enveloped virus poliovirus type 1. This virus was laid on a stainless carrier. The products were spread into the room by hot fogging at 55°C for 30 minutes at a concentration of 7.5 mL.m-3. Poliovirus inoculum, supplemented with 5%, heat inactivated non fat dry organic milk, were applied into the middle of the stainless steel disc and were dried under the air flow of a class II biological safety cabinet at room temperature. The Viral preparations were recovered by using flocked swabs and were titered on Vero cells using the classical Spearman-Kärber CPE reading method, the results were expressed as TCID50.ml-1. Results The infectious titer of dried poliovirus inocula was kept at 105 TCID50.mL-1 up to 150 minutes at room temperature. Dried inocula exposed to airborne peracetic acid containing disinfectants were recovered at 60 and 120 minutes post-exposition and suspended in culture medium again. The cytotoxicity of disinfectant containing medium was eliminated through gel filtration columns. A 4 log reduction of infectious titer of dried poliovirus inocula exposed to peracetic-based airborne disinfectant was obtained. Conclusion This study demonstrates that the virucidal activity of airborne disinfectants can be tested on dried poliovirus. PMID:23587047

[Development of a microenvironment test chamber for airborne microbe research].

Science.gov (United States)

Zhan, Ningbo; Chen, Feng; Du, Yaohua; Cheng, Zhi; Li, Chenyu; Wu, Jinlong; Wu, Taihu

2017-10-01

One of the most important environmental cleanliness indicators is airborne microbe. However, the particularity of clean operating environment and controlled experimental environment often leads to the limitation of the airborne microbe research. This paper designed and implemented a microenvironment test chamber for airborne microbe research in normal test conditions. Numerical simulation by Fluent showed that airborne microbes were evenly dispersed in the upper part of test chamber, and had a bottom-up concentration growth distribution. According to the simulation results, the verification experiment was carried out by selecting 5 sampling points in different space positions in the test chamber. Experimental results showed that average particle concentrations of all sampling points reached 10 7 counts/m 3 after 5 minutes' distributing of Staphylococcus aureus , and all sampling points showed the accordant mapping of concentration distribution. The concentration of airborne microbe in the upper chamber was slightly higher than that in the middle chamber, and that was also slightly higher than that in the bottom chamber. It is consistent with the results of numerical simulation, and it proves that the system can be well used for airborne microbe research.

Short-range airborne transmission of expiratory droplets between two people

DEFF Research Database (Denmark)

Liu, Li; Li, Yuguo; Nielsen, Peter Vilhelm

2017-01-01

, ventilation, and breathing mode. Under the specific set of conditions studied, we found a substantial increase in airborne exposure to droplet nuclei exhaled by the source manikin when a susceptible manikin is within about 1.5 m of the source manikin, referred to as the proximity effect. The threshold...... distance of about 1.5 m distinguishes the two basic transmission processes of droplets and droplet nuclei, that is, short-range modes and the long-range airborne route. The short-range modes include both the conventional large droplet route and the newly defined short-range airborne transmission. We thus...... reveal that transmission occurring in close proximity to the source patient includes both droplet-borne (large droplet) and short-range airborne routes, in addition to the direct deposition of large droplets on other body surfaces. The mechanisms of the droplet-borne and short-range airborne routes...

Airborne Doppler Wind Lidar Post Data Processing Software DAPS-LV

Science.gov (United States)

Beyon, Jeffrey Y. (Inventor); Koch, Grady J. (Inventor); Kavaya, Michael J. (Inventor)

2015-01-01

Systems, methods, and devices of the present invention enable post processing of airborne Doppler wind LIDAR data. In an embodiment, airborne Doppler wind LIDAR data software written in LabVIEW may be provided and may run two versions of different airborne wind profiling algorithms. A first algorithm may be the Airborne Wind Profiling Algorithm for Doppler Wind LIDAR ("APOLO") using airborne wind LIDAR data from two orthogonal directions to estimate wind parameters, and a second algorithm may be a five direction based method using pseudo inverse functions to estimate wind parameters. The various embodiments may enable wind profiles to be compared using different algorithms, may enable wind profile data for long haul color displays to be generated, may display long haul color displays, and/or may enable archiving of data at user-selectable altitudes over a long observation period for data distribution and population.

Integrated application of the database for airborne geophysical survey achievement information

International Nuclear Information System (INIS)

Ji Zengxian; Zhang Junwei

2006-01-01

The paper briefly introduces the database of information for airborne geophysical survey achievements. This database was developed on the platform of Microsoft Windows System with the technical methods of Visual C++ 6.0 and MapGIS. It is an information management system concerning airborne geophysical surveying achievements with perfect functions in graphic display, graphic cutting and output, query of data, printing of documents and reports, maintenance of database, etc. All information of airborne geophysical survey achievements in nuclear industry from 1972 to 2003 was embedded in. Based on regional geological map and Meso-Cenozoic basin map, the detailed statistical information of each airborne survey area, each airborne radioactive anomalous point and high field point can be presented visually by combining geological or basin research result. The successful development of this system will provide a fairly good base and platform for management of archives and data of airborne geophysical survey achievements in nuclear industry. (authors)

Airborne gamma-ray spectrometer and magnetometer survey. Volume I. Final report

International Nuclear Information System (INIS)

An airborne combined radiometric and magnetic survey was performed for the Department of Energy (DOE) over the area covered by the Mariposa, California and Nevada; Fresno, California; and Bakersfield, Caifornia 1:250,000 National Topographic Map Series (NTMS) 1 0 x 2 0 quadrangle maps. The survey was a part of DOE's National Aerial Radiometric Reconnaissance (ARR) program, which in turn is a part of the National Uranium Resource Evaluation (NURE) program. Data were collected by a helicopter equipped with a gamma-ray spectrometer having a large crystal volume, and a high sensitivity proton precession magnetometer. The radiometric system was calibrated at the Walker Field Calibration pads and the Lake Mead Dynamic Test range. Data quality was ensured throughout the survey by daily test flights and equipment checks. Radiometric data were corrected for live time, aircraft and equipment background, cosmic background, atmospheric radon, Compton scatter, and altitude dependence. The corrected data were statistically evaluated, plotted, and contoured to produce anomaly maps based on the radiometric response of individual geological units. These maps were interpreted and an anomaly interpretation map produced. Volume I contains a description of the systems used in the survey, a discussion of the calibration of the systems, the data processing procedures, the data display format, the interpretation rationale, and the interpretation methodology. A separate Volume II for each quadrangle contains the data displays and the interpretation results

Kilometer-Scale Topographic Roughness of Mercury: Correlation with Geologic Features and Units

Science.gov (United States)

Kreslavsky, Mikhail A.; Head, James W.; Neumann, Gregory A.; Zuber, Maria T.; Smith, David E.

2014-01-01

We present maps of the topographic roughness of the northern circumpolar area of Mercury at kilometer scales. The maps are derived from range profiles obtained by the Mercury Laser Altimeter (MLA) instrument onboard the MErcury Surface, Space ENvironment, GEochemistry, and Ranging (MESSENGER) mission. As measures of roughness, we used the interquartile range of profile curvature at three baselines: 0.7 kilometers, 2.8 kilometers, and 11 kilometers. The maps provide a synoptic overview of variations of typical topographic textures. They show a dichotomy between the smooth northern plains and rougher, more heavily cratered terrains. Analysis of the scale dependence of roughness indicates that the regolith on Mercury is thicker than on the Moon by approximately a factor of three. Roughness contrasts within northern volcanic plains of Mercury indicate a younger unit inside Goethe basin and inside another unnamed stealth basin. These new data permit interplanetary comparisons of topographic roughness.

Topographically-controlled site conditions drive vegetation pattern on inland dunes in Poland

Science.gov (United States)

Sewerniak, Piotr; Jankowski, Michał

2017-07-01

The inland dunes of Central Europe are commonly overplanted by Scots pine (Pinus sylvestris) monocultures in which the primary occurrence of the natural vegetation pattern is obliterated. We hypothesize that on naturally revegetated inland dunes the pattern is clear and driven by topographically-controlled site conditions. To test this hypothesis, we addressed the following research questions: (1) Does topography drive vegetation patterns on inland dunes and if so, what are main differences between vegetation in varying relief positions? (2) To what extent does topography involve the variability of microclimates and of soil properties, and how does the topographically-induced differentiation of these site conditions control vegetation patterns? We conducted interdisciplinary studies (applying floristic, pedological and microclimatic research techniques) on a naturally revegetated inland dune area situated on a military artillery training ground near Toruń, northern Poland. We investigated vegetation patterns with reference to three topographical position variants (north-facing slopes, south-facing slopes, and intra-dune depressions). We found distinct differences in vegetation characteristics covering the aforementioned topographical positions. This primarily concerned species composition of ground vegetation: Calluna vulgaris was dominant species on north-facing slopes, Corynephorus canescens on south-facing slopes, while Calamagrostis epigejos in intra-dune depressions. In comparison to dune slopes, the depressions were characterized by much higher biodiversity of vascular plant species. This followed the most favorable soil conditions for the existence of plants (higher moisture and nutrient pools) occurring in low topographical positions. However, tree succession was most advanced not in depressions, where the competitive impact of tall grasses on seedlings was recognized, but on north-facing slopes. Based on our results, we formulated some suggestions, which

New tools for aquatic habitat modeling

Science.gov (United States)

D. Tonina; J. A. McKean; C. Tang; P. Goodwin

2011-01-01

Modeling of aquatic microhabitat in streams has been typically done over short channel reaches using one-dimensional simulations, partly because of a lack of high resolution. subaqueous topographic data to better define model boundary conditions. The Experimental Advanced Airborne Research Lidar (EAARL) is an airborne aquatic-terrestrial sensor that allows simultaneous...

Bilateral topographic symmetry patterns across Aphrodite Terra, Venus

International Nuclear Information System (INIS)

Crumpler, L.S.; Head, J.W.

1988-01-01

Western Aphrodite Terra, Venus, is characterized by a series of parallel linear structural discontinuities 2000--4000 km in length and 100--200 km wide, which strike at high angles to the general topographic trend of the Aphrodite Terra highlands. The broad chracteristics of the cross-strike discontinuities (CSDs) are similar to both strike-slip fault zones and terrestrial oceanic fracture zones. In an effort to distinguish between these two hypotheses, topographic profiles were taken across Aphrodite Terra to test for bilateral symmetry of the type associated with thermal boundary layer topography at divergent plate boundaries on Earth. In addition to a broad bilateral symmetry at a range of angles across Aphrodite Terra, detailed bilateral symmetry is observed within domains between linear discontinuities in directions generally parallel to the strike of the discontinuities. In addition, within a domain the centers of symmetry of several profiles define a linear rise crest that is oriented normal to the bounding CSDs and terminates against them

Sandmeier model based topographic correction to lunar spectral profiler (SP) data from KAGUYA satellite.

Science.gov (United States)

Chen, Sheng-Bo; Wang, Jing-Ran; Guo, Peng-Ju; Wang, Ming-Chang

2014-09-01

The Moon may be considered as the frontier base for the deep space exploration. The spectral analysis is one of the key techniques to determine the lunar surface rock and mineral compositions. But the lunar topographic relief is more remarkable than that of the Earth. It is necessary to conduct the topographic correction for lunar spectral data before they are used to retrieve the compositions. In the present paper, a lunar Sandmeier model was proposed by considering the radiance effect from the macro and ambient topographic relief. And the reflectance correction model was also reduced based on the Sandmeier model. The Spectral Profile (SP) data from KAGUYA satellite in the Sinus Iridum quadrangle was taken as an example. And the digital elevation data from Lunar Orbiter Laser Altimeter are used to calculate the slope, aspect, incidence and emergence angles, and terrain-viewing factor for the topographic correction Thus, the lunar surface reflectance from the SP data was corrected by the proposed model after the direct component of irradiance on a horizontal surface was derived. As a result, the high spectral reflectance facing the sun is decreased and low spectral reflectance back to the sun is compensated. The statistical histogram of reflectance-corrected pixel numbers presents Gaussian distribution Therefore, the model is robust to correct lunar topographic effect and estimate lunar surface reflectance.

Tensor SOM and tensor GTM: Nonlinear tensor analysis by topographic mappings.

Science.gov (United States)

Iwasaki, Tohru; Furukawa, Tetsuo

2016-05-01

In this paper, we propose nonlinear tensor analysis methods: the tensor self-organizing map (TSOM) and the tensor generative topographic mapping (TGTM). TSOM is a straightforward extension of the self-organizing map from high-dimensional data to tensorial data, and TGTM is an extension of the generative topographic map, which provides a theoretical background for TSOM using a probabilistic generative model. These methods are useful tools for analyzing and visualizing tensorial data, especially multimodal relational data. For given n-mode relational data, TSOM and TGTM can simultaneously organize a set of n-topographic maps. Furthermore, they can be used to explore the tensorial data space by interactively visualizing the relationships between modes. We present the TSOM algorithm and a theoretical description from the viewpoint of TGTM. Various TSOM variations and visualization techniques are also described, along with some applications to real relational datasets. Additionally, we attempt to build a comprehensive description of the TSOM family by adapting various data structures. Copyright © 2016 Elsevier Ltd. All rights reserved.

New approach to airborne monitoring of radioactive pollution

International Nuclear Information System (INIS)

Hoeschl, V.; Jurza, P.; Pavlik, B.

1997-01-01

The use of remote sensing methods in the monitoring of an environment is increasing. The best results are obtained when various types of exploration methods are available. This paper presents the use of airborne gamma ray methods, which can be included in a wide scope of works related to environmental problems. It may concern uranium mining areas, areas surrounding various nuclear facilities or areas of Chernobyl fallout. Gamma ray spectrometry data can be combined with airborne magnetic, surface gravity and satellite imagery data to obtain maximum information in data output. Airborne geophysics is able to detect and delineate radioactive contamination and to find important geological trends defining the geological structure of the monitored area. Our company PICODAS Prague Ltd. introduces new sophisticated airborne instrumentation as well as up-to-date data processing and data presentation techniques. In the Czech Cretaceous, a long term project, ''The Structurally-tectonic Survey of the South-West Foreland of the Straz Deposit'' has been undertaken, concerning the ecological load on the environment, especially the pollution of the underground water level horizons due to uranium mining in that area. The major interest is the complicated tectonic structure which interferes heavily with the hydrogeological situation of the region. The paper presents the results of airborne surveys and the interpretation of other geophysical data from the surroundings of Straz pod Ralskem and from Karlovy Vary. (author)

Characteristics of airborne bacteria in Mumbai urban environment.

Science.gov (United States)

Gangamma, S

2014-08-01

Components of biological origin constitute small but a significant proportion of the ambient airborne particulate matter (PM). However, their diversity and role in proinflammatory responses of PM are not well understood. The present study characterizes airborne bacterial species diversity in Mumbai City and elucidates the role of bacterial endotoxin in PM induced proinflammatory response in ex vivo. Airborne bacteria and endotoxin samples were collected during April-May 2010 in Mumbai using six stage microbial impactor and biosampler. The culturable bacterial species concentration was measured and factors influencing the composition were identified by principal component analysis (PCA). The biosampler samples were used to stimulate immune cells in whole blood assay. A total of 28 species belonging to 17 genera were identified. Gram positive and spore forming groups of bacteria dominated the airborne culturable bacterial concentration. The study indicated the dominance of spore forming and human or animal flora derived pathogenic/opportunistic bacteria in the ambient air environment. Pathogenic and opportunistic species of bacteria were also present in the samples. TNF-α induction by PM was reduced (35%) by polymyxin B pretreatment and this result was corroborated with the results of blocking endotoxin receptor cluster differentiation (CD14). The study highlights the importance of airborne biological particles and suggests need of further studies on biological characterization of ambient PM. Copyright © 2014 Elsevier B.V. All rights reserved.

2012 USACE Post Sandy Topographic LiDAR: Coastal Connecticut

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — This data has been acquired and developed by the U.S. Corps of Engineers ST. Louis District to collect and deliver topographic elevation point data derived from...

Topographic Signatures of Meandering Rivers with Differences in Outer Bank Cohesion

Science.gov (United States)

Kelly, S. A.; Belmont, P.

2014-12-01

Within a given valley setting, interactions between river hydraulics, sediment, topography, and vegetation determine attributes of channel morphology, including planform, width and depth, slope, and bed and bank properties. These feedbacks also govern river behavior, including migration and avulsion. Bank cohesion, from the addition of fine sediment and/or vegetation has been recognized in flume experiments as a necessary component to create and maintain a meandering channel planform. Greater bank cohesion slows bank erosion, limiting the rate at which a river can adjust laterally and preventing so-called "runaway widening" to a braided state. Feedbacks of bank cohesion on channel hydraulics and sediment transport may thus produce distinct topographic signatures, or patterns in channel width, depth, and point bar transverse slope. We expect that in bends of greater outer bank cohesion the channel will be narrower, deeper, and bars will have greater transverse slopes. Only recently have we recognized that biotic processes may imprint distinct topographic signatures on the landscape. This study explores topographic signatures of three US rivers: the lower Minnesota River, near Mankato, MN, the Le Sueur River, south central MN, and the Fall River, Rocky Mountain National Park, CO. Each of these rivers has variability in outer bank cohesion, quantified based on geotechnical and vegetation properties, and in-channel topography, which was derived from rtkGPS and acoustic bathymetry surveys. We present methods for incorporating biophysical feedbacks into geomorphic transport laws so that models can better simulate the spatial patterns and variability of topographic signatures.

Topographic Brain Mapping: A Window on Brain Function?

Science.gov (United States)

Karniski, Walt M.

1989-01-01

The article reviews the method of topographic mapping of the brain's electrical activity. Multiple electroencephalogram (EEG) electrodes and computerized analysis of the EEG signal are used to generate maps of frequency and voltage (evoked potential). This relatively new technique holds promise in the evaluation of children with behavioral and…

The NRL 2011 Airborne Sea-Ice Thickness Campaign

Science.gov (United States)

Brozena, J. M.; Gardner, J. M.; Liang, R.; Ball, D.; Richter-Menge, J.

2011-12-01

In March of 2011, the US Naval Research Laboratory (NRL) performed a study focused on the estimation of sea-ice thickness from airborne radar, laser and photogrammetric sensors. The study was funded by ONR to take advantage of the Navy's ICEX2011 ice-camp /submarine exercise, and to serve as a lead-in year for NRL's five year basic research program on the measurement and modeling of sea-ice scheduled to take place from 2012-2017. Researchers from the Army Cold Regions Research and Engineering Laboratory (CRREL) and NRL worked with the Navy Arctic Submarine Lab (ASL) to emplace a 9 km-long ground-truth line near the ice-camp (see Richter-Menge et al., this session) along which ice and snow thickness were directly measured. Additionally, US Navy submarines collected ice draft measurements under the groundtruth line. Repeat passes directly over the ground-truth line were flown and a grid surrounding the line was also flown to collect altimeter, LiDAR and Photogrammetry data. Five CRYOSAT-2 satellite tracks were underflown, as well, coincident with satellite passage. Estimates of sea ice thickness are calculated assuming local hydrostatic balance, and require the densities of water, ice and snow, snow depth, and freeboard (defined as the elevation of sea ice, plus accumulated snow, above local sea level). Snow thickness is estimated from the difference between LiDAR and radar altimeter profiles, the latter of which is assumed to penetrate any snow cover. The concepts we used to estimate ice thickness are similar to those employed in NASA ICEBRIDGE sea-ice thickness estimation. Airborne sensors used for our experiment were a Reigl Q-560 scanning topographic LiDAR, a pulse-limited (2 nS), 10 GHz radar altimeter and an Applanix DSS-439 digital photogrammetric camera (for lead identification). Flights were conducted on a Twin Otter aircraft from Pt. Barrow, AK, and averaged ~ 5 hours in duration. It is challenging to directly compare results from the swath LiDAR with the

Vector Topographic Map Data over the BOREAS NSA and SSA in SIF Format

Science.gov (United States)

Knapp, David; Nickeson, Jaime; Hall, Forrest G. (Editor)

2000-01-01

This data set contains vector contours and other features of individual topographic map sheets from the National Topographic Series (NTS). The map sheet files were received in Standard Interchange Format (SIF) and cover the BOReal Ecosystem-Atmosphere Study (BOREAS) Northern Study Area (NSA) and Southern Study Area (SSA) at scales of 1:50,000 and 1:250,000. The individual files are stored in compressed Unix tar archives.

Multi-scale Visualization of Remote Sensing and Topographic Data of the Amazon Rain Forest for Environmental Monitoring of the Petroleum Industry.

Science.gov (United States)

Fonseca, L.; Miranda, F. P.; Beisl, C. H.; Souza-Fonseca, J.

2002-12-01

PETROBRAS (the Brazilian national oil company) built a pipeline to transport crude oil from the Urucu River region to a terminal in the vicinities of Coari, a city located in the right margin of the Solimoes River. The oil is then shipped by tankers to another terminal in Manaus, capital city of the Amazonas state. At the city of Coari, changes in water level between dry and wet seasons reach up to 14 meters. This strong seasonal character of the Amazonian climate gives rise to four distinct scenarios in the annual hydrological cycle: low water, high water, receding water, and rising water. These scenarios constitute the main reference for the definition of oil spill response planning in the region, since flooded forests and flooded vegetation are the most sensitive fluvial environments to oil spills. This study focuses on improving information about oil spill environmental sensitivity in Western Amazon by using 3D visualization techniques to help the analysis and interpretation of remote sensing and digital topographic data, as follows: (a) 1995 low flood and 1996 high flood JERS-1 SAR mosaics, band LHH, 100m pixel; (b) 2000 low flood and 2001 high flood RADARSAT-1 W1 images, band CHH, 30m pixel; (c) 2002 high flood airborne SAR images from the SIVAM project (System for Surveillance of the Amazon), band LHH, 3m pixel and band XHH, 6m pixel; (d) GTOPO30 digital elevation model, 30' resolution; (e) Digital elevation model derived from topographic information acquired during seismic surveys, 25m resolution; (f) panoramic views obtained from low altitude helicopter flights. The methodology applied includes image processing, cartographic conversion and generation of value-added product using 3D visualization. A semivariogram textural classification was applied to the SAR images in order to identify areas of flooded forest and flooded vegetation. The digital elevation models were color shaded to highlight subtle topographic features. Both datasets were then converted to

Airborne concentrations of radioactive materials in severe accidents

International Nuclear Information System (INIS)

Ross, D.F. Jr.; Denning, R.S.

1989-01-01

Radioactive materials would be released to the containment building of a commercial nuclear reactor during each of the stages of a severe accident. Results of analyses of two accident sequences are used to illustrate the magnitudes of these sources of radioactive materials, the resulting airborne mass concentrations, the characteristics of the airborne aerosols, the potential for vapor forms of radioactive materials, the effectiveness of engineered safety features in reducing airborne concentrations, and the release of radioactive materials to the environment. Ability to predict transport and deposition of radioactive materials is important to assessing the performance of containment safety features in severe accidents and in the development of accident management procedures to reduce the consequences of severe accidents

An experimental and theoretical study of pendellösung fringes in synchrotron section topographs of silicon wafers.

Science.gov (United States)

Partanen, J; Tuomi, T

1990-01-01

X-ray section topographs of nearly perfect Czochralski-grown wafers were made with synchrotron radiation having a continuous spectrum. An intensity curve measured from the x-ray film is compared to the calculated curve obtained using the dynamical theory of x-ray diffraction. A computer simulation of the topograph is also presented. A good agreement between theory and experiment is found except in the middle part of the topograph.

Topographic Patterns of Mortality and Succession in the Alpine Treeline Ecotone Suggest Hydrologic Controls on Post-Fire Tree Establishment

Science.gov (United States)

McCaffrey, D. R.; Hopkinson, C.

2017-12-01

Alpine Treeline Ecotone (ATE), the transition zone between closed canopy forest and alpine tundra, is a prominent vegetation pattern in mountain regions. At continental scales, the elevation of ATE is negatively correlated with latitude and is generally explained by thermal limitations. However, at landscape scales, precipitation and moisture regimes can suppress ATE elevation below thermal limits, causing variability and patterning in ATE position. Recent studies have investigated the relative effects of hydroclimatic variables on ATE position at multiple scales, but less attention has been given to interactions between hydroclimatic variables and disturbance agents, such as fire. Observing change in the ATE at sufficient spatial resolution and temporal extent to identify correlations between topographic variables and disturbance agents has proved challenging. Recent advances in monoplotting have enabled the extraction of canopy cover information from oblique photography, at a resolution of 20 m. Using airborne lidar and repeat photography from the Mountain Legacy Project, we observed canopy cover change in West Castle Watershed (Alberta, Canada; 103 km2; 49.3° N, 114.4° W) over a 92-year period (i.e. 1914-2006). Two wildfires, occurring 1934 and 1936, affected 63% of the watershed area, providing an opportunity to contrast topographic patterns of mortality and succession in the ATE, while factoring by exposure to fire. Slope aspect was a strong predictor of mortality and succession: the frequency of mortality was four times higher in fire-exposed areas, with 72% of all mortality occurring on south- and east-facing slope aspects; the frequency of succession was balanced between fire-exposed and unexposed areas, with 66% of all succession occurred on north- and east-facing slope aspects. Given previous experiments have demonstrated that moisture limitation inhibits tree establishment, suppressing elevation of ATE below thermal growth boundaries, we hypothesize

Factors contributing to airborne particle dispersal in the operating room.

Science.gov (United States)

Noguchi, Chieko; Koseki, Hironobu; Horiuchi, Hidehiko; Yonekura, Akihiko; Tomita, Masato; Higuchi, Takashi; Sunagawa, Shinya; Osaki, Makoto

2017-07-06

Surgical-site infections due to intraoperative contamination are chiefly ascribable to airborne particles carrying microorganisms. The purpose of this study is to identify the actions that increase the number of airborne particles in the operating room. Two surgeons and two surgical nurses performed three patterns of physical movements to mimic intraoperative actions, such as preparing the instrument table, gowning and donning/doffing gloves, and preparing for total knee arthroplasty. The generation and behavior of airborne particles were filmed using a fine particle visualization system, and the number of airborne particles in 2.83 m 3 of air was counted using a laser particle counter. Each action was repeated five times, and the particle measurements were evaluated through one-way analysis of variance multiple comparison tests followed by Tukey-Kramer and Bonferroni-Dunn multiple comparison tests for post hoc analysis. Statistical significance was defined as a P value ≤ .01. A large number of airborne particles were observed while unfolding the surgical gown, removing gloves, and putting the arms through the sleeves of the gown. Although numerous airborne particles were observed while applying the stockinet and putting on large drapes for preparation of total knee arthroplasty, fewer particles (0.3-2.0 μm in size) were detected at the level of the operating table under laminar airflow compared to actions performed in a non-ventilated preoperative room (P airborne particles near a sterile area and that laminar airflow has the potential to reduce the incidence of bacterial contamination.

Effects of riparian vegetation on topographic change during a large flood event, Rio Puerco, New Mexico, USA

Science.gov (United States)

Perignon, M. C.; Tucker, G. E.; Griffin, E. R.; Friedman, J. M.

2013-09-01

The spatial distribution of riparian vegetation can strongly influence the geomorphic evolution of dryland rivers during large floods. We present the results of an airborne lidar differencing study that quantifies the topographic change that occurred along a 12 km reach of the Lower Rio Puerco, New Mexico, during an extreme event in 2006. Extensive erosion of the channel banks took place immediately upstream of the study area, where tamarisk and sandbar willow had been removed. Within the densely vegetated study reach, we measure a net volumetric change of 578,050 ± ˜ 490,000 m3, with 88.3% of the total aggradation occurring along the floodplain and channel and 76.7% of the erosion focusing on the vertical valley walls. The sediment derived from the devegetated reach deposited within the first 3.6 km of the study area, with depth decaying exponentially with distance downstream. Elsewhere, floodplain sediments were primarily sourced from the erosion of valley walls. Superimposed on this pattern are the effects of vegetation and valley morphology on sediment transport. Sediment thickness is seen to be uniform among sandbar willows and highly variable within tamarisk groves. These reach-scale patterns of sedimentation observed in the lidar differencing likely reflect complex interactions of vegetation, flow, and sediment at the scale of patches to individual plants.

Particle dry-deposition experiment using ambient airborne soil

International Nuclear Information System (INIS)

Sehmel, G.A.

1979-01-01

Airborne solid concentrations were measured simultaneously at sampling towers upwind and 305-m downwind of a site. When the wind speed and wind direction were identical at each site, isokinetic air samplers on the sampling towers were automatically activated. The fraction of the airborne solid plume remaining after the 305-m fetch ranged from 0.53 to 1.07

Generating Topographic Map Data from Classification Results

Directory of Open Access Journals (Sweden)

Joachim Höhle

2017-03-01

Full Text Available The use of classification results as topographic map data requires cartographic enhancement and checking of the geometric accuracy. Urban areas are of special interest. The conversion of the classification result into topographic map data of high thematic and geometric quality is subject of this contribution. After reviewing the existing literature on this topic, a methodology is presented. The extraction of point clouds belonging to line segments is solved by the Hough transform. The mathematics for deriving polygons of orthogonal, parallel and general line segments by least squares adjustment is presented. A unique solution for polylines, where the Hough parameters are optimized, is also given. By means of two data sets land cover maps of six classes were produced and then enhanced by the proposed method. The classification used the decision tree method applying a variety of attributes including object heights derived from imagery. The cartographic enhancement is carried out with two different levels of quality. The user’s accuracies for the classes “impervious surface” and “building” were above 85% in the “Level 1” map of Example 1. The geometric accuracy of building corners at the “Level 2” maps is assessed by means of reference data derived from ortho-images. The obtained root mean square errors (RMSE of the generated coordinates (x, y were RMSEx = 1.2 m and RMSEy = 0.7 m (Example 1 and RMSEx = 0.8 m and RMSEy = 1.0 m (Example 2 using 31 and 62 check points, respectively. All processing for Level 1 (raster data could be carried out with a high degree of automation. Level 2 maps (vector data were compiled for the classes “building” and “road and parking lot”. For urban areas with numerous classes and of large size, universal algorithms are necessary to produce vector data fully automatically. The recent progress in sensors and machine learning methods will support the generation of topographic map data of high

Teaching Topographic Map Skills and Geomorphology Concepts with Google Earth in a One-Computer Classroom

Science.gov (United States)

Hsu, Hsiao-Ping; Tsai, Bor-Wen; Chen, Che-Ming

2018-01-01

Teaching high-school geomorphological concepts and topographic map reading entails many challenges. This research reports the applicability and effectiveness of Google Earth in teaching topographic map skills and geomorphological concepts, by a single teacher, in a one-computer classroom. Compared to learning via a conventional instructional…

Airborne evaluation/verification of antenna patterns of broadcasting stations

NARCIS (Netherlands)

Witvliet, Ben

2006-01-01

This paper describes a method for airborne evaluation and verification of the antenna patterns of broadcasting stations. Although it is intended for governmental institutions and broadcasters it may be also of interest to anyone who wants to evaluate large radiating structures. An airborne

Solar Terminator Waves in the Ionosphere Measured by the Wallops Island, VA Dynasonde

Science.gov (United States)

Zabotin, N. A.; Song, H.; Bullett, T. W.

2017-12-01

Solar terminator represents a unique source of atmospheric waves possessing of near-ideal coherent properties: its geometry and magnitude of the impact changes very little from day to day. This feature has been used in [Forbes et al., GRL, 2008] to obtain "snapshots" of terminator waves in the neutral atmosphere at the altitude 400 km by averaging CHAMP accelerometer data over relatively long sequences of the satellite passes. The results were represented in the geographic latitude vs local time coordinates. We apply a similar approach averaging time series of Wallops Island, VA Dynasonde Doppler data to obtain "snapshots" of terminator waves in the ionosphere in the true altitude vs local "terminator time" coordinates. The averaging is performed independently for every month of the yearlong observation period from May 2013 to April 2014. The altitude range covered is 90 km to 400 km with 2 km resolution, representing the entire bottom-side ionosphere. Individual local time segments used for the averaging were 12 hours long and all centered at the times of the sunrise or sunset terminator passing at every specific altitude. This procedure effectively suppresses all kinds of incoherent wave activity and allows one to reveal the perturbation phenomenon mainly caused by the solar terminator. This is an important advantage of this technique compared to multiple "terminator wave" studies based on simple time coincidence. Both sunrise and sunset terminator waves are easily visualized in all of the monthly images. Our results confirm observations of [Forbes et al., GRL, 2008] of the wave structures existing on both sides of the terminator. The phase fronts of the sunset terminator wave are propagating downward indicating upward movement of the terminator-related disturbance and of the wave energy generated by it. The phase fronts of the sunrise terminator waves are propagating upward indicating downward movement of the terminator-related disturbance and of the wave energy

Airborne Next: Rethinking Airborne Organization and Applying New Concepts

Science.gov (United States)

2015-06-01

9 Kenneth Macksey, Guderian: Panzer General-revised EDITION (South Yorkshire, England: Greenhill Books, 2003), 1–20. 10 Dr. John Arquilla...Airborne Operations: Field Manual 90=26, 1–5. 14 The 1st Special Forces Regiment has five active Special Forces Groups (1st, 3rd, 5th , 7th, 10th...Oxford University Press, 1981). Headrick, in his book, describes the interplay between technology and imperialism. For the purposes of this research

CAMEX-4 ER-2 MODIS AIRBORNE SIMULATOR (MAS) V1

Data.gov (United States)

National Aeronautics and Space Administration — The MODIS Airborne Simulator (MAS) is an airborne scanning spectrometer that acquires high spatial resolution imagery of cloud and surface features from its vantage...

Elements of the Chicxulub Impact Structure as revealed in SRTM and surface GPS topographic data

Science.gov (United States)

Kobrick, M.; Kinsland, G. L.; Sanchez, G.; Cardador, M. H.

2003-04-01

Pope et al have utilized elevations from the Petroleos Mexicanos (PEMEX) gravity data files to show that the main component of the surface expression of the Chicxu-lub Impact Structure is a roughly semi-circular, low-relief depression about 90 km in diameter. They also identified other topographic features and the elements of the buried impact which possibly led to the development of these features. Kinsland et al presented a connection between these topographic anomalies, small gravity anomalies and buried structure of the impact. Shaded relief images from recently acquired SRTM elevation data clearly show the circular depression of the crater and the moat/cenote ring. In addition we can readily identify Inner trough 1, Inner trough 2 and Outer trough as defined by Pope et al. The agreement between the topographic maps of Pope et al, Kinsland et al and SRTM data are remarkable considering that the distribution and types of data in the sets are so different. We also have ground topographic data collected with a special "autonomous differ-ential GPS" system during summer 2002. Profiles from these data generally agree with both the gravity data based topographic maps and profiles extracted from the SRTM data. Preliminary analyses of our new data, SRTM and GPS, have uncovered features not previously recognized: 1) as shown by the GPS data the moat/cenote ring consists of two distinct depressions separated by about 10 km...perhaps separate ring faults, 2) in the SRTM data over the southern part of the crater and on southward for perhaps 20 km beyond the moat/ cenote ring there exists a pattern, as yet unexplained, of roughly concentric topographic features whose center lies at about 21deg 40min N and 89deg 25min W, about 50km NNE of the moat/cenote ring center. The corroboration and better definition of the previously recognized topographic features yielded by the two new forms of data strengthens the cases for these fea-tures and for their relevance to the underlying

EUFAR training opportunities to advance European airborne research

Science.gov (United States)

Reusen, I.; Brenguier, J.-L.; Brown, P.; Wendish, M.

2009-04-01

EUFAR, EUropean Facilities for Airborne Research, is an FP7 project (http://www.eufar.net) funded by the European Commission with 33 partners that aims at providing and improving the access to European airborne facilities (i.e. aircraft, airborne instruments, data processing centres) for researchers in environmental and geo-sciences through Networking Activities, Transnational Access and Joint Research Activities. This paper reports on the training opportunities within EUFAR for European researchers. In EUFAR three types of training opportunities are offered: 1) Participate in training courses (ET-TC) 2) Join an existing field campaign (ET-EC) 3) Participate in the design of a new field campaign (ET-TA), in the frame of EUFAR Transnational Access and tutored by more experienced researchers. During the 4-year EUFAR project (2008-2012), 4 training courses covering the complete chain from acquisition to interpretation of airborne data and images will be organised during spring/summer for early-stage researchers as well as university lecturers (new in FP7 EUFAR) in airborne research. The training courses will have an equal focus on theory and practical training/demonstration and each training course will be accompanied by a "student" airborne field campaign. Participants will be trained by top-class scientists, aircraft and/or instrument operators and each participant will get the opportunity to design his/her own experiment and to participate to that flight experiment. Furthermore, researchers have the opportunity to join an existing field campaign and work with more experienced researchers, aircraft and/or instrument operators. The list of airborne field campaigns open to join and the eligibility criteria, can be consulted at the EUFAR website. Finally, researchers have the opportunity to participate in the design of a new field campaign in the frame of EUFAR Transnational Access (TA). TA provides access to either aircraft or instrumentation that are not otherwise

Airborne Nanostructured Particles and Occupational Health

Science.gov (United States)

Maynard, Andrew D.; Kuempel, Eileen D.

2005-12-01

Nanotechnology is leading to the development in many field, of new materials and devices in many fields that demonstrate nanostructure-dependent properties. However, concern has been expressed that these same properties may present unique challenges to addressing potential health impact. Airborne particles associated with engineered nanomaterials are of particular concern, as they can readily enter the body through inhalation. Research into the potential occupational health risks associated with inhaling engineered nanostructured particles is just beginning. However, there is a large body of data on occupational and environmental aerosols, which is applicable to developing an initial assessment of potential risk and risk reduction strategies. Epidemiological and pathological studies of occupational and environmental exposures to airborne particles and fibers provide information on the aerosol-related lung diseases and conditions that have been observed in humans. Toxicological studies provide information on the specific disease mechanisms, dose-response relationships, and the particle characteristics that influence toxicity, including the size, surface area, chemistry or reactivity, solubility, and shape. Potential health risk will depend on the magnitude and nature of exposures to airborne nanostructured particles, and on the release, dispersion, transformation and control of materials in the workplace. Aerosol control methods have not been well-characterized for nanometer diameter particles, although theory and limited experimental data indicate that conventional ventilation, engineering control and filtration approaches should be applicable in many situations. Current information supports the development of preliminary guiding principles on working with engineered nanomaterials. However critical research questions remain to be answered before the potential health risk of airborne nanostructured particles in the workplace can be fully addressed.

Toolsets for Airborne Data (TAD): Enhanced Airborne Data Merging Functionality through Spatial and Temporal Subsetting

Science.gov (United States)

Early, A. B.; Chen, G.; Beach, A. L., III; Northup, E. A.

2016-12-01

NASA has conducted airborne tropospheric chemistry studies for over three decades. These field campaigns have generated a great wealth of observations, including a wide range of the trace gases and aerosol properties. The Atmospheric Science Data Center (ASDC) at NASA Langley Research Center in Hampton Virginia originally developed the Toolsets for Airborne Data (TAD) web application in September 2013 to meet the user community needs for manipulating aircraft data for scientific research on climate change and air quality relevant issues. The analysis of airborne data typically requires data subsetting, which can be challenging and resource intensive for end users. In an effort to streamline this process, the TAD toolset enhancements will include new data subsetting features and updates to the current database model. These will include two subsetters: temporal and spatial, and vertical profile. The temporal and spatial subsetter will allow users to both focus on data from a specific location and/or time period. The vertical profile subsetter will retrieve data collected during an individual aircraft ascent or descent spiral. This effort will allow for the automation of the typically labor-intensive manual data subsetting process, which will provide users with data tailored to their specific research interests. The development of these enhancements will be discussed in this presentation.

An integrated compact airborne multispectral imaging system using embedded computer

Science.gov (United States)

Zhang, Yuedong; Wang, Li; Zhang, Xuguo

2015-08-01

An integrated compact airborne multispectral imaging system using embedded computer based control system was developed for small aircraft multispectral imaging application. The multispectral imaging system integrates CMOS camera, filter wheel with eight filters, two-axis stabilized platform, miniature POS (position and orientation system) and embedded computer. The embedded computer has excellent universality and expansibility, and has advantages in volume and weight for airborne platform, so it can meet the requirements of control system of the integrated airborne multispectral imaging system. The embedded computer controls the camera parameters setting, filter wheel and stabilized platform working, image and POS data acquisition, and stores the image and data. The airborne multispectral imaging system can connect peripheral device use the ports of the embedded computer, so the system operation and the stored image data management are easy. This airborne multispectral imaging system has advantages of small volume, multi-function, and good expansibility. The imaging experiment results show that this system has potential for multispectral remote sensing in applications such as resource investigation and environmental monitoring.

Evaluation of topographic index in relation to terrain roughness and ...

Indian Academy of Sciences (India)

of landslide susceptibility (Yesilnacar and Topal .... network. Topographic index is used by different researchers considering different DEM grid ...... TOPMODEL into GIS; Environ. .... ping: A comparison of logistic regression and neural net-.

2006 URS Corporation Bare Earth Topographic Lidar: Shawsheen River, Massachusetts

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — URS Corporation contracted EarthData International to aquire topographic elevation data for 82 square miles in Essex and Middlesex Counties, Massachusetts during...

ATM Coastal Topography-Louisiana, 2001: UTM Zone 15 (Part 1 of 2)

Science.gov (United States)

Yates, Xan; Nayegandhi, Amar; Brock, John C.; Sallenger, A.H.; Klipp, Emily S.; Wright, C. Wayne

2010-01-01

These remotely sensed, geographically referenced elevation measurements of lidar-derived first-surface (FS) topography were produced collaboratively by the U.S. Geological Survey (USGS), Florida Integrated Science Center (FISC), St. Petersburg, FL, and the National Aeronautics and Space Administration (NASA), Wallops Flight Facility, VA. This project provides highly detailed and accurate datasets of a portion of the Louisiana coastline beach face within UTM Zone 15, from Isles Dernieres to Grand Isle, acquired September 7 and 10, 2001. The datasets are made available for use as a management tool to research scientists and natural-resource managers. An innovative scanning lidar instrument originally developed by NASA, and known as the Airborne Topographic Mapper (ATM), was used during data acquisition. The ATM system is a scanning lidar system that measures high-resolution topography of the land surface and incorporates a green-wavelength laser operating at pulse rates of 2 to 10 kilohertz. Measurements from the laser-ranging device are coupled with data acquired from inertial navigation system (INS) attitude sensors and differentially corrected global positioning system (GPS) receivers to measure topography of the surface at accuracies of +/-15 centimeters. The nominal ATM platform is a Twin Otter or P-3 Orion aircraft, but the instrument may be deployed on a range of light aircraft. Elevation measurements were collected over the survey area using the ATM system, and the resulting data were then processed using the Airborne Lidar Processing System (ALPS), a custom-built processing system developed in a NASA-USGS collaboration. ALPS supports the exploration and processing of lidar data in an interactive or batch mode. Modules for presurvey flight-line definition, flight-path plotting, lidar raster and waveform investigation, and digital camera image playback have been developed. Processing algorithms have been developed to extract the range to the first and last

ATM Coastal Topography-Texas, 2001: UTM Zone 15

Science.gov (United States)

Klipp, Emily S.; Nayegandhi, Amar; Brock, John C.; Sallenger, A.H.; Bonisteel, Jamie M.; Yates, Xan; Wright, C. Wayne

2009-01-01

These remotely sensed, geographically referenced elevation measurements of lidar-derived first-surface (FS) topography were produced collaboratively by the U.S. Geological Survey (USGS), Florida Integrated Science Center (FISC), St. Petersburg, FL, and the National Aeronautics and Space Administration (NASA), Wallops Flight Facility, VA. This project provides highly detailed and accurate datasets of a portion of the Texas coastline within UTM zone 15, from Matagorda Peninsula to Galveston Island, acquired October 12-13, 2001. The datasets are made available for use as a management tool to research scientists and natural-resource managers. An innovative scanning lidar instrument originally developed by NASA, and known as the Airborne Topographic Mapper (ATM), was used during data acquisition. The ATM system is a scanning lidar system that measures high-resolution topography of the land surface and incorporates a green-wavelength laser operating at pulse rates of 2 to 10 kilohertz. Measurements from the laser-ranging device are coupled with data acquired from inertial navigation system (INS) attitude sensors and differentially corrected global positioning system (GPS) receivers to measure topography of the surface at accuracies of +/-15 centimeters. The nominal ATM platform is a Twin Otter or P-3 Orion aircraft, but the instrument may be deployed on a range of light aircraft. Elevation measurements were collected over the survey area using the ATM system, and the resulting data were then processed using the Airborne Lidar Processing System (ALPS), a custom-built processing system developed in a NASA-USGS collaboration. ALPS supports the exploration and processing of lidar data in an interactive or batch mode. Modules for presurvey flight-line definition, flight-path plotting, lidar raster and waveform investigation, and digital camera image playback have been developed. Processing algorithms have been developed to extract the range to the first and last significant

ATM Coastal Topography - Louisiana, 2001: UTM Zone 16 (Part 2 of 2)

Science.gov (United States)

Yates, Xan; Nayegandhi, Amar; Brock, John C.; Sallenger, Asbury H.; Klipp, Emily S.; Wright, C. Wayne

2009-01-01

These remotely sensed, geographically referenced elevation measurements of lidar-derived first-surface (FS) topography were produced collaboratively by the U.S. Geological Survey (USGS), Florida Integrated Science Center (FISC), St. Petersburg, FL, and the National Aeronautics and Space Administration (NASA), Wallops Flight Facility, VA. This project provides highly detailed and accurate datasets of a portion of the Louisiana coastline beach face within UTM Zone 16, from Grand Isle to the Chandeleur Islands, acquired September 7 and 9, 2001. The datasets are made available for use as a management tool to research scientists and natural-resource managers. An innovative scanning lidar instrument originally developed by NASA, and known as the Airborne Topographic Mapper (ATM), was used during data acquisition. The ATM system is a scanning lidar system that measures high-resolution topography of the land surface and incorporates a green-wavelength laser operating at pulse rates of 2 to 10 kilohertz. Measurements from the laser-ranging device are coupled with data acquired from inertial navigation system (INS) attitude sensors and differentially corrected global positioning system (GPS) receivers to measure topography of the surface at accuracies of +/-15 centimeters. The nominal ATM platform is a Twin Otter or P-3 Orion aircraft, but the instrument may be deployed on a range of light aircraft. Elevation measurements were collected over the survey area using the ATM system, and the resulting data were then processed using the Airborne Lidar Processing System (ALPS), a custom-built processing system developed in a NASA-USGS collaboration. ALPS supports the exploration and processing of lidar data in an interactive or batch mode. Modules for presurvey flight-line definition, flight-path plotting, lidar raster and waveform investigation, and digital camera image playback have been developed. Processing algorithms have been developed to extract the range to the first and

Detection in Urban Scenario Using Combined Airborne Imaging Sensors

NARCIS (Netherlands)

Renhorn, I.; Axelsson, M.; Benoist, K.W.; Bourghys, D.; Boucher, Y.; Xavier Briottet, X.; Sergio De CeglieD, S. De; Dekker, R.J.; Dimmeler, A.; Dost, R.; Friman, O.; Kåsen, I.; Maerker, J.; Persie, M. van; Resta, S.; Schwering, P.B.W.; Shimoni, M.; Vegard Haavardsholm, T.

2012-01-01

The EDA project “Detection in Urban scenario using Combined Airborne imaging Sensors” (DUCAS) is in progress. The aim of the project is to investigate the potential benefit of combined high spatial and spectral resolution airborne imagery for several defense applications in the urban area. The

Detection in Urban Scenario using Combined Airborne Imaging Sensors

NARCIS (Netherlands)

Renhorn, I.; Axelsson, M.; Benoist, K.W.; Bourghys, D.; Boucher, Y.; Xavier Briottet, X.; Sergio De CeglieD, S. De; Dekker, R.J.; Dimmeler, A.; Dost, R.; Friman, O.; Kåsen, I.; Maerker, J.; Persie, M. van; Resta, S.; Schwering, P.B.W.; Shimoni, M.; Vegard Haavardsholm, T.

2012-01-01

The EDA project “Detection in Urban scenario using Combined Airborne imaging Sensors” (DUCAS) is in progress. The aim of the project is to investigate the potential benefit of combined high spatial and spectral resolution airborne imagery for several defense applications in the urban area. The

Acoustically sticky topographic metasurfaces for underwater sound absorption.

Science.gov (United States)

Lee, Hunki; Jung, Myungki; Kim, Minsoo; Shin, Ryung; Kang, Shinill; Ohm, Won-Suk; Kim, Yong Tae

2018-03-01

A class of metasurfaces for underwater sound absorption, based on a design principle that maximizes thermoviscous loss, is presented. When a sound meets a solid surface, it leaves a footprint in the form of thermoviscous boundary layers in which energy loss takes place. Considered to be a nuisance, this acoustic to vorticity/entropy mode conversion and the subsequent loss are often ignored in the existing designs of acoustic metamaterials and metasurfaces. The metasurface created is made of a series of topographic meta-atoms, i.e., intaglios and reliefs engraved directly on the solid object to be concealed. The metasurface is acoustically sticky in that it rather facilitates the conversion of the incident sound to vorticity and entropy modes, hence the thermoviscous loss, leading to the desired anechoic property. A prototype metasurface machined on a brass object is tested for its anechoicity, and shows a multitude of absorption peaks as large as unity in the 2-5 MHz range. Computations also indicate that a topographic metasurface is robust to hydrostatic pressure variation, a quality much sought-after in underwater applications.

Ferromagnetic resonance in a topographically modulated permalloy film

Science.gov (United States)

Sklenar, J.; Tucciarone, P.; Lee, R. J.; Tice, D.; Chang, R. P. H.; Lee, S. J.; Nevirkovets, I. P.; Heinonen, O.; Ketterson, J. B.

2015-04-01

A major focus within the field of magnonics involves the manipulation and control of spin-wave modes. This is usually done by patterning continuous soft magnetic films. Here, we report on work in which we use topographic modifications of a continuous magnetic thin film, rather than lithographic patterning techniques, to modify the ferromagnetic resonance spectrum. To demonstrate this technique we have performed in-plane, broadband, ferromagnetic resonance studies on a 100-nm-thick permalloy film sputtered onto a colloidal crystal with individual sphere diameters of 200 nm. Effects resulting from the, ideally, sixfold-symmetric underlying colloidal crystal were studied as a function of the in-plane field angle through experiment and micromagnetic modeling. Experimentally, we find two primary modes; the ratio of the intensities of these two modes exhibits a sixfold dependence. Detailed micromagnetic modeling shows that both modes are quasiuniform and nodeless in the unit cell but that they reside in different demagnetized regions of the unit cell. Our results demonstrate that topographic modification of magnetic thin films opens additional directions for manipulating ferromagnetic resonant excitations.

Planning a radar system for protection from the airborne threat

International Nuclear Information System (INIS)

Greneker, E.F.; McGee, M.C.

1986-01-01

A planning methodology for developing a radar system to protect nuclear materials facilities from the airborne threat is presented. Planning for physical security to counter the airborne threat is becoming even more important because hostile acts by terrorists are increasing and airborne platforms that can be used to bypass physical barriers are readily available. The comprehensive system planning process includes threat and facility surveys, defense hardening, analysis of detection and early warning requirements, optimization of sensor mix and placement, and system implementation considerations

Potential airborne release from soil-working operations in a contaminated area

International Nuclear Information System (INIS)

Sutter, S.L.

1980-08-01

Experiments were performed to provide an indication of how much material could be made airborne during soil-working operations in a contaminated area. Approximately 50 kg of contaminated soil were collected, dried, and mixed, and particle size distribution and 137 Cs content were characterized. In four experiments performed in a 2 ft x 2 ft wind tunnel at the Radioactive Aerosol Release Test Facility, soil was pumped into an airstream moving at 3.2, 10.4, 15.2, and 20 mph. These experiments were designed to maximize airborne releases by fluidizing the soil as it was pumped into the wind tunnel. Thus the airborne releases should represent upper limit values for soil-working operations. Airborne concentration and particle size samples were collected and all of the material deposited downstream was collected to calculate a mass balance. The fraction airborne was calculated using these measurements

Airborne chemicals cause respiratory symptoms in individuals with contact allergy

DEFF Research Database (Denmark)

Elberling, J; Linneberg, A; Mosbech, H

2005-01-01

Exposure to fragrance chemicals causes various eye and airway symptoms. Individuals with perfume contact allergy report these symptoms more frequently than individuals with nickel allergy or no contact allergies. However, the associations between contact allergy and respiratory symptoms elicited...... by airborne chemicals other than perfumes are unclear. The study aimed to investigate the association between eye and airway symptoms elicited by airborne chemicals (other than perfumes) and contact allergy in a population-based sample. A questionnaire on respiratory symptoms was posted, in 2002, to 1189...... individuals who participated in 1997/1998 in a Danish population-based study of allergic diseases. Questions about eye and airway symptoms elicited by different airborne chemicals and airborne proteins were included in the questionnaire. Data from the questionnaire were compared with data on patch testing...

Dispersion model for airborne radioactive particulates inside a process building

International Nuclear Information System (INIS)

Perkins, W.C.; Stoddard, D.H.

1984-02-01

An empirical model, predicting the spread of airborne radioactive particles after they are released inside a building, has been developed. The basis for this model is a composite of data for dispersion of airborne activity recorded during 12 case incidents. These incidents occurred at the Savannah River Plant (SRP) during approximately 90 plant-years of experience with the chemical and metallurgical processing of purified neptunium and plutonium. The model illustrates that the multiple-air-zone concept, used in the designs of many nuclear facilities, can be an efficient safety feature to limit the spread of airborne activity from a release. This study also provides some insight into an apparently anomalous behavior of airborne particulates, namely, their migration against the prevailing flow of ventilation air. 2 references, 12 figures, 4 tables

Airborne particulate concentrations and fluxes at an active uranium mill tailings site

International Nuclear Information System (INIS)

Sehmel, G.A.

1978-01-01

Direct measurements of airborne particulate concentrations and fluxes of transported mill tailing materials were measured at an active mill tailings site. Experimental measurement equipment consisted of meteorological instrumentation to automatically activate total particulate air samplers as a function of wind speed increments and direction, as well as particle cascade impactors to measure airborne respirable concentrations as a function of particle size. In addition, an inertial impaction device measured nonrespirable fluxes of airborne particles. Caclulated results are presented in terms of the airborne solid concentration in g/m 3 , the horizontal airborne mass flux in g/(m 2 -day) for total collected nonrespirable particles and the radionuclide concentrations in dpm/g as a function of particle diameter for respirable and nonrespirable particles

Airborne and Maritime/Fixed Station Joint Tactical Radio System (AMF JTRS)

Science.gov (United States)

2015-12-01

Selected Acquisition Report (SAR) RCS: DD-A&T(Q&A)823-421 Airborne & Maritime/Fixed Station Joint Tactical Radio System (AMF JTRS) As of FY 2017...Information Program Name Airborne & Maritime/Fixed Station Joint Tactical Radio System (AMF JTRS) DoD Component Army Responsible Office References SAR...UNCLASSIFIED 5 Mission and Description Airborne & Maritime/Fixed Station Joint Tactical Radio System (AMF JTRS) products are software programmable

Safety certification of airborne software: An empirical study

International Nuclear Information System (INIS)

Dodd, Ian; Habli, Ibrahim

2012-01-01

Many safety-critical aircraft functions are software-enabled. Airborne software must be audited and approved by the aerospace certification authorities prior to deployment. The auditing process is time-consuming, and its outcome is unpredictable, due to the criticality and complex nature of airborne software. To ensure that the engineering of airborne software is systematically regulated and is auditable, certification authorities mandate compliance with safety standards that detail industrial best practice. This paper reviews existing practices in software safety certification. It also explores how software safety audits are performed in the civil aerospace domain. The paper then proposes a statistical method for supporting software safety audits by collecting and analysing data about the software throughout its lifecycle. This method is then empirically evaluated through an industrial case study based on data collected from 9 aerospace projects covering 58 software releases. The results of this case study show that our proposed method can help the certification authorities and the software and safety engineers to gain confidence in the certification readiness of airborne software and predict the likely outcome of the audits. The results also highlight some confidentiality issues concerning the management and retention of sensitive data generated from safety-critical projects.

Topographic Data Development for Miami County 1m LiDAR

Data.gov (United States)

Federal Emergency Management Agency, Department of Homeland Security — Terrain data, as defined in FEMA Guidelines and Specifications, Appendix N: Data Capture Standards, describes the digital topographic data that was used to create...

An Airborne Capability for South Africa from a Special Operations ...

African Journals Online (AJOL)

term strategy, and airborne forces form an important component in its envisioned Contingency Brigade. This article examines the utility of contemporary airborne forces despite the decline in major parachute assaults. It also explains the ...

Geoid of Nepal from airborne gravity survey

DEFF Research Database (Denmark)

Forsberg, René; Olesen, Arne Vestergaard; Einarsson, Indriði

2011-01-01

An airborne gravity survey of Nepal was carried out December 2010 in a cooperation between DTU-Space, Nepal Survey Department, and NGA, USA. The entire country was flown with survey lines spaced 6 nm with a King Air aircraft, with a varying flight altitude from 4 to 10 km. The survey operations...... as well as recent GPS-heights of Mt. Everest. The new airborne data also provide an independent validation of GOCE gravity field results at the local ~100 km resolution scale....

Airborne gamma-ray spectrometer and magnetometer survey: Peoria, Decater, Belleville Quadrangles, (IL). Final report

International Nuclear Information System (INIS)

1981-01-01

An airborne combined radiometric and magnetic survey was performed for the Department of Energy (DOE) over the area covered by the Peoria, Decatur, and Belleville, 1:250,000 National Topographic Map Series (NTMS), quadrangle maps. The survey was part of DOE's National Uranium Resource Evaluation (NURE) program. Data were collected by a helicopter equipped with a gamma-ray spectrometer with a large crystal volume, and with a high sensitivity proton procession magnetometer. The radiometric system was calibrated at the Walker Field Calibration pads and the Lake Mead Dynamic Test Range. Data quality was ensured during the survey by daily test flights and equipment checks. Radiometric data were corrected for live time, aircraft and equipment background, cosmic background, atmospheric radon, Compton scatter, and altitude dependence. The corrected data were statistically evaluated, plotted, and contoured to produce anomaly maps based on the radiometric response of individual geological units. The anomalies were interpreted and an interpretation map produced. Volume I contains a description of the systems used in the survey, a discussion of the calibration of the systems, the data collection procedures, the data processing procedures, the data presentation, the interpretation rationale, and the interpretation methodology. A separate Volume II for each quadrangle contains the data displays and the interpretation results

A geologic analysis of the Side-Looking Airborne Radar imagery of southern New England

Science.gov (United States)

Banks, Paul T.

1975-01-01

Analysis of the side looking airborn radar imagery of Massachusetts, Connecticut and Rhode Island indicates that radar shows the topography in great detail. Since bedrock geologic features are frequently expressed in the topography the radar lends itself to geologic interpretation. The radar was studied by comparisons with field mapped geologic data first at a scale of approximately 1:125,000 and then at a scale of 1:500,000. The larger scale comparison revealed that faults, minor faults, joint sets, bedding and foliation attitudes, lithology and lithologic contacts all have a topographic expression interpretable on the imagery. Surficial geologic features were far less visible on the imagery over most of the area studied. The smaller scale comparisons revealed a pervasive, near orthogonal fracture set cutting all types and ages of rock and trending roughly N40?E and N30?W. In certain places the strike of bedding and foliation attitudes and some lithologic Contacts were visible in addition to the fractures. Fracturing in southern New England is apparently far more important than has been previously recognized. This new information, together with the visibility of many bedding and foliation attitudes and lithologic contacts, indicates the importance of radar imagery in improving the geologic interpretation of an area.

Topographic Correction Module at Storm (TC@Storm)

Science.gov (United States)

Zaksek, K.; Cotar, K.; Veljanovski, T.; Pehani, P.; Ostir, K.

2015-04-01

Different solar position in combination with terrain slope and aspect result in different illumination of inclined surfaces. Therefore, the retrieved satellite data cannot be accurately transformed to the spectral reflectance, which depends only on the land cover. The topographic correction should remove this effect and enable further automatic processing of higher level products. The topographic correction TC@STORM was developed as a module within the SPACE-SI automatic near-real-time image processing chain STORM. It combines physical approach with the standard Minnaert method. The total irradiance is modelled as a three-component irradiance: direct (dependent on incidence angle, sun zenith angle and slope), diffuse from the sky (dependent mainly on sky-view factor), and diffuse reflected from the terrain (dependent on sky-view factor and albedo). For computation of diffuse irradiation from the sky we assume an anisotropic brightness of the sky. We iteratively estimate a linear combination from 10 different models, to provide the best results. Dependent on the data resolution, we mask shades based on radiometric (image) or geometric properties. The method was tested on RapidEye, Landsat 8, and PROBA-V data. Final results of the correction were evaluated and statistically validated based on various topography settings and land cover classes. Images show great improvements in shaded areas.

Improved ice loss estimate of the northwestern Greenland ice sheet

DEFF Research Database (Denmark)

Kjeldsen, Kristian Kjellerup; Khan, Shfaqat Abbas; Wahr, J.

2013-01-01

We estimate ice volume change rates in the northwest Greenland drainage basin during 2003–2009 using Ice, Cloud and land Elevation Satellite (ICESat) laser altimeter data. Elevation changes are often reported to be largest near the frontal portion of outlet glaciers. To improve the volume change...... estimate, we supplement the ICESat data with altimeter surveys from NASA's Airborne Topographic Mapper from 2002 to 2010 and NASA's Land, Vegetation and Ice Sensor from 2010. The Airborne data are mainly concentrated along the ice margin and thus have a significant impact on the estimate of the volume...... change. Our results show that adding Airborne Topographic Mapper and Land, Vegetation and Ice Sensor data to the ICESat data increases the catchment-wide estimate of ice volume loss by 11%, mainly due to an improved volume loss estimate along the ice sheet margin. Furthermore, our results show...

Role of interoceptive accuracy in topographical changes in emotion-induced bodily sensations

Science.gov (United States)

Jung, Won-Mo; Ryu, Yeonhee; Lee, Ye-Seul; Wallraven, Christian; Chae, Younbyoung

2017-01-01

The emotion-associated bodily sensation map is composed of a specific topographical distribution of bodily sensations to categorical emotions. The present study investigated whether or not interoceptive accuracy was associated with topographical changes in this map following emotion-induced bodily sensations. This study included 31 participants who observed short video clips containing emotional stimuli and then reported their sensations on the body map. Interoceptive accuracy was evaluated with a heartbeat detection task and the spatial patterns of bodily sensations to specific emotions, including anger, fear, disgust, happiness, sadness, and neutral, were visualized using Statistical Parametric Mapping (SPM) analyses. Distinct patterns of bodily sensations were identified for different emotional states. In addition, positive correlations were found between the magnitude of sensation in emotion-specific regions and interoceptive accuracy across individuals. A greater degree of interoceptive accuracy was associated with more specific topographical changes after emotional stimuli. These results suggest that the awareness of one’s internal bodily states might play a crucial role as a required messenger of sensory information during the affective process. PMID:28877218

Airborne system for mapping and tracking extended gamma ray sources

International Nuclear Information System (INIS)

Stuart, T.P.; Hendricks, T.J.; Wallace, G.G.; Cleland, J.R.

1976-01-01

An airborne system was developed for mapping and tracking extended sources of airborne or terrestrially distributed γ-ray emitters. The system records 300 channel γ-ray spectral data every three seconds on magnetic tape. Computer programs have been written to isolate the contribution from the particular radionuclide of interest. Aircraft position as sensed by a microwave ranging system is recorded every second on magnetic tape. Measurements of airborne stack releases of 41 A concentrations versus time or aircraft position agree well with computer code predictions

The Topographic Data Deluge - Collecting and Maintaining Data in a 21ST Century Mapping Agency

Science.gov (United States)

Holland, D. A.; Pook, C.; Capstick, D.; Hemmings, A.

2016-06-01

In the last few years, the number of sensors and data collection systems available to a mapping agency has grown considerably. In the field, in addition to total stations measuring position, angles and distances, the surveyor can choose from hand-held GPS devices, multi-lens imaging systems or laser scanners, which may be integrated with a laptop or tablet to capture topographic data directly in the field. These systems are joined by mobile mapping solutions, mounted on large or small vehicles, or sometimes even on a backpack carried by a surveyor walking around a site. Such systems allow the raw data to be collected rapidly in the field, while the interpretation of the data can be performed back in the office at a later date. In the air, large format digital cameras and airborne lidar sensors are being augmented with oblique camera systems, taking multiple views at each camera position and being used to create more realistic 3D city models. Lower down in the atmosphere, Unmanned Aerial Vehicles (or Remotely Piloted Aircraft Systems) have suddenly become ubiquitous. Hundreds of small companies have sprung up, providing images from UAVs using ever more capable consumer cameras. It is now easy to buy a 42 megapixel camera off the shelf at the local camera shop, and Canon recently announced that they are developing a 250 megapixel sensor for the consumer market. While these sensors may not yet rival the metric cameras used by today's photogrammetrists, the rapid developments in sensor technology could eventually lead to the commoditization of high-resolution camera systems. With data streaming in from so many sources, the main issue for a mapping agency is how to interpret, store and update the data in such a way as to enable the creation and maintenance of the end product. This might be a topographic map, ortho-image or a digital surface model today, but soon it is just as likely to be a 3D point cloud, textured 3D mesh, 3D city model, or Building Information Model

Analysis of Alabama Airborne Gravity at Three Altitudes: Expected Accuracy and Spatial Resolution from a Future Tibetan Airborne Gravity Survey

Directory of Open Access Journals (Sweden)

Chi-Hsun Huang

2013-01-01

Full Text Available In situ airborne gravity data at altitudes of 11, 6.3, and 1.7 km over a smooth area of Alabama are used to assess gravity accuracy and errors in upward and downward continuations. Analysis of the Alabama free-air anomaly gravity data at crossover points at the three altitudes suggests 1 - 2 mgal accuracy for the dataset. Gravity data at each altitude are then expanded into local 3D Fourier series, to prepare for continuation. This Fourier representation results in continuation errors at few-mgal level in Alabama, even in the extreme case of downward continuation from 11 km to sea level. The result in Alabama inspires an airborne gravity survey over the rough, inaccessible terrain of Tibet. Similar investigations as in Alabama are made in Tibet using EGM08-derived airborne gravity data at flight altitudes of 10, 5, and 0 km. Bouguer anomalies at the 10-km altitude preserve the major tectonic features of Tibet. Downward continuation errors increase with terrain roughness, but the survey can enhance local tectonic features. This study highlights the value of a future Tibetan airborne gravity survey and points out the expected gravity accuracy and spatial resolution from this survey.

Space-Wise approach for airborne gravity data modelling

Science.gov (United States)

Sampietro, D.; Capponi, M.; Mansi, A. H.; Gatti, A.; Marchetti, P.; Sansò, F.

2017-05-01

Regional gravity field modelling by means of remove-compute-restore procedure is nowadays widely applied in different contexts: it is the most used technique for regional gravimetric geoid determination, and it is also used in exploration geophysics to predict grids of gravity anomalies (Bouguer, free-air, isostatic, etc.), which are useful to understand and map geological structures in a specific region. Considering this last application, due to the required accuracy and resolution, airborne gravity observations are usually adopted. However, due to the relatively high acquisition velocity, presence of atmospheric turbulence, aircraft vibration, instrumental drift, etc., airborne data are usually contaminated by a very high observation error. For this reason, a proper procedure to filter the raw observations in both the low and high frequencies should be applied to recover valuable information. In this work, a software to filter and grid raw airborne observations is presented: the proposed solution consists in a combination of an along-track Wiener filter and a classical Least Squares Collocation technique. Basically, the proposed procedure is an adaptation to airborne gravimetry of the Space-Wise approach, developed by Politecnico di Milano to process data coming from the ESA satellite mission GOCE. Among the main differences with respect to the satellite application of this approach, there is the fact that, while in processing GOCE data the stochastic characteristics of the observation error can be considered a-priori well known, in airborne gravimetry, due to the complex environment in which the observations are acquired, these characteristics are unknown and should be retrieved from the dataset itself. The presented solution is suited for airborne data analysis in order to be able to quickly filter and grid gravity observations in an easy way. Some innovative theoretical aspects focusing in particular on the theoretical covariance modelling are presented too

Airborne Tactical Intent-Based Conflict Resolution Capability

Science.gov (United States)

Wing, David J.; Vivona, Robert A.; Roscoe, David A.

2009-01-01

Trajectory-based operations with self-separation involve the aircraft taking the primary role in the management of its own trajectory in the presence of other traffic. In this role, the flight crew assumes the responsibility for ensuring that the aircraft remains separated from all other aircraft by at least a minimum separation standard. These operations are enabled by cooperative airborne surveillance and by airborne automation systems that provide essential monitoring and decision support functions for the flight crew. An airborne automation system developed and used by NASA for research investigations of required functionality is the Autonomous Operations Planner. It supports the flight crew in managing their trajectory when responsible for self-separation by providing monitoring and decision support functions for both strategic and tactical flight modes. The paper focuses on the latter of these modes by describing a capability for tactical intent-based conflict resolution and its role in a comprehensive suite of automation functions supporting trajectory-based operations with self-separation.

Neural correlates of British sign language comprehension: spatial processing demands of topographic language.

Science.gov (United States)

MacSweeney, Mairéad; Woll, Bencie; Campbell, Ruth; Calvert, Gemma A; McGuire, Philip K; David, Anthony S; Simmons, Andrew; Brammer, Michael J

2002-10-01

In all signed languages used by deaf people, signs are executed in "sign space" in front of the body. Some signed sentences use this space to map detailed "real-world" spatial relationships directly. Such sentences can be considered to exploit sign space "topographically." Using functional magnetic resonance imaging, we explored the extent to which increasing the topographic processing demands of signed sentences was reflected in the differential recruitment of brain regions in deaf and hearing native signers of the British Sign Language. When BSL signers performed a sentence anomaly judgement task, the occipito-temporal junction was activated bilaterally to a greater extent for topographic than nontopographic processing. The differential role of movement in the processing of the two sentence types may account for this finding. In addition, enhanced activation was observed in the left inferior and superior parietal lobules during processing of topographic BSL sentences. We argue that the left parietal lobe is specifically involved in processing the precise configuration and location of hands in space to represent objects, agents, and actions. Importantly, no differences in these regions were observed when hearing people heard and saw English translations of these sentences. Despite the high degree of similarity in the neural systems underlying signed and spoken languages, exploring the linguistic features which are unique to each of these broadens our understanding of the systems involved in language comprehension.

Topographically mediated controls on aboveground biomass across a mediterranean-type landscape

Science.gov (United States)

Dahlin, K.; Asner, G. P.; Field, C. B.

2009-12-01

Aboveground biomass accumulation is a useful metric for evaluating habitat restoration and ecosystem services projects, in addition to being a robust measure of carbon sequestration. However, at the landscape scale non-anthropogenic controls on biomass accumulation are poorly understood. In this study we combined field measurements, high resolution data from the NASA JPL Airborne Visible/Infrared Imaging Spectrometer (AVIRIS), and the Carnegie Airborne Observatory (CAO) airborne light detection and ranging (lidar) system to create a comprehensive map of aboveground biomass across a patchy mediterranean-type landscape (Jasper Ridge Biological Preserve, Stanford, CA). Candidate explanatory variables (e.g. slope, elevation, incident solar radiation) were developed using a geologic map and a digital elevation model derived from the lidar data. Finally, candidate variables were tested, and a model was produced to predict aboveground biomass from environmental data. Though many of the explanatory variables have only indirect effects on plant growth, the model permits inferences to be made about the relative importance of light, water, temperature, and edaphic characteristics on carbon accumulation in mediterranean-type systems.

30 CFR 56.5001 - Exposure limits for airborne contaminants.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Exposure limits for airborne contaminants. 56... Quality and Physical Agents Air Quality § 56.5001 Exposure limits for airborne contaminants. Except as... contaminants shall not exceed, on the basis of a time weighted average, the threshold limit values adopted by...

An Assessment of the Evolving Common Metadata Repository Standards for Airborne Field Campaigns

Science.gov (United States)

Northup, E. A.; Chen, G.; Early, A. B.; Beach, A. L., III; Walter, J.; Conover, H.

2016-12-01

The NASA Earth Venture Program has led to a dramatic increase in airborne observations, requiring updated data management practices with clearly defined data standards and protocols for metadata. While the current data management practices demonstrate some success in serving airborne science team data user needs, existing metadata models and standards such as NASA's Unified Metadata Model (UMM) for Collections (UMM-C) present challenges with respect to accommodating certain features of airborne science metadata. UMM is the model implemented in the Common Metadata Repository (CMR), which catalogs all metadata records for NASA's Earth Observing System Data and Information System (EOSDIS). One example of these challenges is with representation of spatial and temporal metadata. In addition, many airborne missions target a particular geophysical event, such as a developing hurricane. In such cases, metadata about the event is also important for understanding the data. While coverage of satellite missions is highly predictable based on orbit characteristics, airborne missions feature complicated flight patterns where measurements can be spatially and temporally discontinuous. Therefore, existing metadata models will need to be expanded for airborne measurements and sampling strategies. An Airborne Metadata Working Group was established under the auspices of NASA's Earth Science Data Systems Working Group (ESDSWG) to identify specific features of airborne metadata that can not be currently represented in the UMM and to develop new recommendations. The group includes representation from airborne data users and providers. This presentation will discuss the challenges and recommendations in an effort to demonstrate how airborne metadata curation/management can be improved to streamline data ingest and discoverability to a broader user community.

Airborne plutonium transported during southwesterly winds near the Hanford Prosser Barricade

International Nuclear Information System (INIS)

Sehmel, G.A.

1980-01-01

Airborne plutonium could result from resuspension of nuclear-weapons-testing stratospheric fallout deposition. To determine this possible resuspension at the Hanford site, two field experiments between April 12 to june 29, 1976 and August 12, 1976 to January 11, 1977 were conducted near the Prosser Barricade in the Hanford area about 19 to 22 km southeast (140 0 to 160 0 ) of the fuel-processing areas. The primary objective of these experimentss was to determine if stratospheric fallout resuspension was reflected by airborne plutonium concentrations increasing with increasing wind speed. A secondary objective was to confirm the source of the airborne plutonium by determining the plutonium-240 isotopic content or the plutonium-240/plutonium-239-mass ratio. Stratospheric fallout can be identified by the ratio of 240 Pu to other plutonium isotopes in surface soils. Plutonium was transported during southwesterly winds during the two study periods at the Prosser Barricade. Airborne 239 240 Pu concentrations varied as powers of wind speed (U):U -0 2 to U 7 8 . The airborne solids content ranged from 6 x 10 -8 to 1.7 x 10 -6 μCi/g. The 240 Pu isotopic content ranged from 5.6 to 8.1 atom percent and the 240 Pu/ 239 Pu mass ratio ranged from 0.065 to 0.089. The estimated fraction of stratospheric fallout plutonium in these samples was less than 0.24. The remaining airborne plutonium was probably of Hanford origin. Airborne plutonium probably represents resuspension of plutonium from undetermined sites by mechanisms and events not clear at present. An increasing airborne plutonium concentration with increasing wind speed might be expected for an upwind resuspension source(s). However, the geographical source(s) location was not investigated in this study

Detection Range of Airborne Magnetometers in Magnetic Anomaly Detection

Directory of Open Access Journals (Sweden)

Chengjing Li

2015-11-01

Full Text Available Airborne magnetometers are utilized for the small-range search, precise positioning, and identification of the ferromagnetic properties of underwater targets. As an important performance parameter of sensors, the detection range of airborne magnetometers is commonly set as a fixed value in references regardless of the influences of environment noise, target magnetic properties, and platform features in a classical model to detect airborne magnetic anomalies. As a consequence, deviation in detection ability analysis is observed. In this study, a novel detection range model is proposed on the basis of classic detection range models of airborne magnetometers. In this model, probability distribution is applied, and the magnetic properties of targets and the environment noise properties of a moving submarine are considered. The detection range model is also constructed by considering the distribution of the moving submarine during detection. A cell-averaging greatest-of-constant false alarm rate test method is also used to calculate the detection range of the model at a desired false alarm rate. The detection range model is then used to establish typical submarine search probabilistic models. Results show that the model can be used to evaluate not only the effects of ambient magnetic noise but also the moving and geomagnetic features of the target and airborne detection platform. The model can also be utilized to display the actual operating range of sensor systems.

Evaluation and parameterization of ATCOR3 topographic correction method for forest cover mapping in mountain areas

Science.gov (United States)

Balthazar, Vincent; Vanacker, Veerle; Lambin, Eric F.

2012-08-01

A topographic correction of optical remote sensing data is necessary to improve the quality of quantitative forest cover change analyses in mountainous terrain. The implementation of semi-empirical correction methods requires the calibration of model parameters that are empirically defined. This study develops a method to improve the performance of topographic corrections for forest cover change detection in mountainous terrain through an iterative tuning method of model parameters based on a systematic evaluation of the performance of the correction. The latter was based on: (i) the general matching of reflectances between sunlit and shaded slopes and (ii) the occurrence of abnormal reflectance values, qualified as statistical outliers, in very low illuminated areas. The method was tested on Landsat ETM+ data for rough (Ecuadorian Andes) and very rough mountainous terrain (Bhutan Himalayas). Compared to a reference level (no topographic correction), the ATCOR3 semi-empirical correction method resulted in a considerable reduction of dissimilarities between reflectance values of forested sites in different topographic orientations. Our results indicate that optimal parameter combinations are depending on the site, sun elevation and azimuth and spectral conditions. We demonstrate that the results of relatively simple topographic correction methods can be greatly improved through a feedback loop between parameter tuning and evaluation of the performance of the correction model.

Topographical effects of climate dataset and their impacts on the estimation of regional net primary productivity

Science.gov (United States)

Sun, L. Qing; Feng, Feng X.

2014-11-01

In this study, we first built and compared two different climate datasets for Wuling mountainous area in 2010, one of which considered topographical effects during the ANUSPLIN interpolation was referred as terrain-based climate dataset, while the other one did not was called ordinary climate dataset. Then, we quantified the topographical effects of climatic inputs on NPP estimation by inputting two different climate datasets to the same ecosystem model, the Boreal Ecosystem Productivity Simulator (BEPS), to evaluate the importance of considering relief when estimating NPP. Finally, we found the primary contributing variables to the topographical effects through a series of experiments given an overall accuracy of the model output for NPP. The results showed that: (1) The terrain-based climate dataset presented more reliable topographic information and had closer agreements with the station dataset than the ordinary climate dataset at successive time series of 365 days in terms of the daily mean values. (2) On average, ordinary climate dataset underestimated NPP by 12.5% compared with terrain-based climate dataset over the whole study area. (3) The primary climate variables contributing to the topographical effects of climatic inputs for Wuling mountainous area were temperatures, which suggest that it is necessary to correct temperature differences for estimating NPP accurately in such a complex terrain.

Simulation of X-ray topographs: a new method to calculate the diffracted field

International Nuclear Information System (INIS)

Carvalho, C.A.M.; Epelboin, Y.

1993-01-01

The precision of the numerical algorithms used to integrate the Takagi-Taupin equations has been in the past a severe limitation for the simulation of accurate topographs. The intensity, especially in the direct image of the defect, is underestimated. This has forbidden the use of the reciprocity theorem for the simulation of traverse and white-beam synchrotron topographs. A new algorithm is described, based on two different methods of expressing the partial-derivative equations, which permits a faster and more accurate calculation. (orig.)

Influence of salt concentration and topographical position on water ...

African Journals Online (AJOL)

Water resource quality (WRQ) is affected by salt concentration and topographical position. Indeed, an increase in salt concentration, which decreases water availability for animal and plant nutrition, and lower altitude, which diminishes the potential for production of hydropower, negatively affects WRQ. Therefore, it is useful ...

X-ray Topographic Investigations of Domain Structure in Czochralski Grown PrxLa1-xAlO3 Crystals

International Nuclear Information System (INIS)

Wieteska, K.; Wierzchowski, W.; Malinowska, A.; Turczynski, S.; Pawlak, D.A.; Lukasiewicz, T.; Lefeld-Sosnowska, M.; Graeff, W.

2010-01-01

In the present paper X-ray diffraction topographic techniques were applied to a number of samples cut from Czochralski grown Pr x La 1-x AlO 3 crystals with different ratio of praseodymium and lanthanum. Conventional and synchrotron X-ray topographic investigations revealed differently developed domain structures dependent on the composition of mixed praseodymium lanthanum aluminium perovskites. Some large mosaic blocks were observed together with the domains. In the best crystals, X-ray topographs revealed striation fringes and individual dislocations inside large domains. Synchrotron topographs allowed us to indicate that the domains correspond to three different crystallographic planes, and to evaluate the lattice misorientation between domains in the range of 20-50 arc min (authors)

Air ICP uses for instantaneous monitoring of airborne pollutants

International Nuclear Information System (INIS)

Thouzeau, F.; Birolleau, J.C.; Fieni, J.M.; Bergey, C.

1987-01-01

Recently the development of a pure AIR-ICP which breathes in and excites the analysed air without sample dilution, allowed the application of this technique to the real time analysis of airborne metallic pollutants. First results obtained on airborne Beryllium in a laboratory and a test-site apparatus are presented in this paper

76 FR 50808 - Airborne Supplemental Navigation Equipment Using the Global Positioning System (GPS)

Science.gov (United States)

2011-08-16

... DEPARTMENT OF TRANSPORTATION Federal Aviation Administration Airborne Supplemental Navigation.... ACTION: Notice of intent to cancel Technical Standard Order (TSO)- C129a, Airborne Supplemental... notice announces the FAA's intent to cancel TSO-C129a, Airborne Supplemental Navigation Equipment Using...

Application of Ifsar Technology in Topographic Mapping: JUPEM's Experience

Science.gov (United States)

Zakaria, Ahamad

2018-05-01

The application of Interferometric Synthetic Aperture Radar (IFSAR) in topographic mapping has increased during the past decades. This is due to the advantages that IFSAR technology offers in solving data acquisition problems in tropical regions. Unlike aerial photography, radar technology offers wave penetration through cloud cover, fog and haze. As a consequence, images can be made free of any natural phenomenon defects. In Malaysia, Department of Survey and Mapping Malaysia (JUPEM) has been utilizing the IFSAR products since 2009 to update topographic maps at 1 : 50,000 map scales. Orthorectified radar imagery (ORI), Digital Surface Models (DSM) and Digital Terrain Models (DTM) procured under the project have been further processed before the products are ingested into a revamped mapping workflow consisting of stereo and mono digitizing processes. The paper will highlight the experience of Department of Survey and Mapping Malaysia (DSMM)/ JUPEM in using such technology in order to speed up mapping production.

Construction Method of the Topographical Features Model for Underwater Terrain Navigation

Directory of Open Access Journals (Sweden)

Wang Lihui

2015-09-01

Full Text Available Terrain database is the reference basic for autonomous underwater vehicle (AUV to implement underwater terrain navigation (UTN functions, and is the important part of building topographical features model for UTN. To investigate the feasibility and correlation of a variety of terrain parameters as terrain navigation information metrics, this paper described and analyzed the underwater terrain features and topography parameters calculation method. Proposing a comprehensive evaluation method for terrain navigation information, and constructing an underwater navigation information analysis model, which is associated with topographic features. Simulation results show that the underwater terrain features, are associated with UTN information directly or indirectly, also affect the terrain matching capture probability and the positioning accuracy directly.

AIRBORNE CONTACT DERMATITIS – CURRENT PERSPECTIVES IN ETIOPATHOGENESIS AND MANAGEMENT

Science.gov (United States)

Handa, Sanjeev; De, Dipankar; Mahajan, Rahul

2011-01-01

The increasing recognition of occupational origin of airborne contact dermatitis has brought the focus on the variety of irritants, which can present with this typical morphological picture. At the same time, airborne allergic contact dermatitis secondary to plant antigens, especially to Compositae family, continues to be rampant in many parts of the world, especially in the Indian subcontinent. The recognition of the contactant may be difficult to ascertain and the treatment may be even more difficult. The present review focuses on the epidemiological, clinical and therapeutic issues in airborne contact dermatitis. PMID:22345774

Airborne gravimetry used in precise geoid computations by ring integration

DEFF Research Database (Denmark)

Kearsley, A.H.W.; Forsberg, René; Olesen, Arne Vestergaard

1998-01-01

Two detailed geoids have been computed in the region of North Jutland. The first computation used marine data in the offshore areas. For the second computation the marine data set was replaced by the sparser airborne gravity data resulting from the AG-MASCO campaign of September 1996. The results...... of comparisons of the geoid heights at on-shore geometric control showed that the geoid heights computed from the airborne gravity data matched in precision those computed using the marine data, supporting the view that airborne techniques have enormous potential for mapping those unsurveyed areas between...

Multispectral Terrain Background Simulation Techniques For Use In Airborne Sensor Evaluation

Science.gov (United States)

Weinberg, Michael; Wohlers, Ronald; Conant, John; Powers, Edward

1988-08-01

A background simulation code developed at Aerodyne Research, Inc., called AERIE is designed to reflect the major sources of clutter that are of concern to staring and scanning sensors of the type being considered for various airborne threat warning (both aircraft and missiles) sensors. The code is a first principles model that could be used to produce a consistent image of the terrain for various spectral bands, i.e., provide the proper scene correlation both spectrally and spatially. The code utilizes both topographic and cultural features to model terrain, typically from DMA data, with a statistical overlay of the critical underlying surface properties (reflectance, emittance, and thermal factors) to simulate the resulting texture in the scene. Strong solar scattering from water surfaces is included with allowance for wind driven surface roughness. Clouds can be superimposed on the scene using physical cloud models and an analytical representation of the reflectivity obtained from scattering off spherical particles. The scene generator is augmented by collateral codes that allow for the generation of images at finer resolution. These codes provide interpolation of the basic DMA databases using fractal procedures that preserve the high frequency power spectral density behavior of the original scene. Scenes are presented illustrating variations in altitude, radiance, resolution, material, thermal factors, and emissivities. The basic models utilized for simulation of the various scene components and various "engineering level" approximations are incorporated to reduce the computational complexity of the simulation.

Unravelling spatio-temporal evapotranspiration patterns in topographically complex landscapes

Science.gov (United States)

Metzen, Daniel; Sheridan, Gary; Nyman, Petter; Lane, Patrick

2016-04-01

Vegetation co-evolves with soils and topography under a given long-term climatic forcing. Previous studies demonstrated a strong eco-hydrologic feedback between topography, vegetation and energy and water fluxes. Slope orientation (aspect and gradient) alter the magnitude of incoming solar radiation resulting in larger evaporative losses and less water availability on equator-facing slopes. Furthermore, non-local water inputs from upslope areas potentially contribute to available water at downslope positions. The combined effect of slope orientation and drainage position creates complex spatial patterns in biological productivity and pedogenesis, which in turn alter the local hydrology. In complex upland landscapes, topographic alteration of incoming radiation can cause substantial aridity index (ratio of potential evapotranspiration to precipitation) variations over small spatial extents. Most of the upland forests in south-east Australia are located in an aridity index (AI) range of 1-2, around the energy limited to water limited boundary, where forested systems are expected to be most sensitive to AI changes. In this research we aim to improve the fundamental understanding of spatio-temporal evolution of evapotranspiration (ET) patterns in complex terrain, accounting for local topographic effects on system properties (e.g. soil depth, sapwood area, leaf area) and variation in energy and water exchange processes due to slope orientation and drainage position. Six measurement plots were set-up in a mixed species eucalypt forest on a polar and equatorial-facing hillslope (AI ˜1.3 vs. 1.8) at varying drainage position (ridge, mid-slope, gully), while minimizing variations in other factors, e.g. geology and weather patterns. Sap flow, soil water content, incoming solar radiation and throughfall were continuously monitored at field sites spanning a wide range of soil depth (0.5 - >3m), maximum tree heights (17 - 51m) and LAI (1.2 - 4.6). Site-specific response curves

Exhumation and topographic evolution of the Namche Barwa Syntaxis, eastern Himalaya

Science.gov (United States)

Yang, Rong; Herman, Frédéric; Fellin, Maria Giuditta; Maden, Colin

2018-01-01

The Namche Barwa Syntaxis, as one of the most tectonically active regions, remains an appropriate place to explore the relationship between tectonics, surface processes, and landscape evolution. Two leading models have been proposed for the formation and evolution of this syntaxis, including the tectonic aneurysm model and the syntaxis expansion model. Here we use a multi-disciplinary approach based on low-temperature thermochronometry, numerical modeling, river profile and topographic analyses to investigate the interactions between tectonics, erosion, and landscape evolution and to test these models. Our results emphasize the presence of young cooling ages (i.e., River, to the north of the syntaxis. Using numerical modeling we argue that a recent increase in exhumation rate is required to expose these young ages. Our river analysis reveals spatial variations in channel steepness, which we interpret to reflect the rock uplift pattern. By establishing the relationship between erosion rates and topographic features, we find that erosion rates are poorly to weakly correlated with topographic features, suggesting that the landscape is still evolving. Altogether, these results seem better explained by a mechanism that involves a northward expansion of the syntaxis, which causes high rock uplift rates to the north of the syntaxis and a transient state of topography adjusting to an evolving tectonic setting.

Debris flow-induced topographic changes: effects of recurrent debris flow initiation.

Science.gov (United States)

Chen, Chien-Yuan; Wang, Qun

2017-08-12

Chushui Creek in Shengmu Village, Nantou County, Taiwan, was analyzed for recurrent debris flow using numerical modeling and geographic information system (GIS) spatial analysis. The two-dimensional water flood and mudflow simulation program FLO-2D were used to simulate debris flow induced by rainfall during typhoon Herb in 1996 and Mindulle in 2004. Changes in topographic characteristics after the debris flows were simulated for the initiation of hydrological characteristics, magnitude, and affected area. Changes in topographic characteristics included those in elevation, slope, aspect, stream power index (SPI), topographic wetness index (TWI), and hypsometric curve integral (HI), all of which were analyzed using GIS spatial analysis. The results show that the SPI and peak discharge in the basin increased after a recurrence of debris flow. The TWI was higher in 2003 than in 2004 and indicated higher potential of landslide initiation when the slope of the basin was steeper. The HI revealed that the basin was in its mature stage and was shifting toward the old stage. Numerical simulation demonstrated that the parameters' mean depth, maximum depth, affected area, mean flow rate, maximum flow rate, and peak flow discharge were increased after recurrent debris flow, and peak discharge occurred quickly.

Plutonium concentrations in airborne soil at Rocky Flats and Hanford determined during resuspension experiments

International Nuclear Information System (INIS)

Sehmel, G.A.

1978-01-01

Plutonium resuspension results are summarized for experiments conducted by the author at Rocky Flats, onsite on the Hanford reservation, and for winds blowing from offsite onto the Hanford reservation near the Prosser barricade boundary. In each case, plutonium resuspension was shown by increased airborne plutonium concentrations as a function of either wind speed or as compared to fallout levels. All measured airborne concentrations were far below maximum permissible concentrations (MPC). Both plutonium and cesium concentrations on airborne soil were normalized by the quantity of airborne soil sampled. Airborne radionuclide concentrations in μCi/g were related to published values for radionuclide concentrations on surface soils. For this ratio of radionuclide concentration per gram on airborne soil divided by that for ground surface soil, there are eight orders of magnitude uncertainty from 10 -4 to 10 4 . This uncertainty in the equality between plutonium concentrations per gram on airborne and surface soils is caused by only a fraction of the collected airborne soil being transported from offsite rather than all being resuspended from each study site and also by the great variabilities in surface contamination. Horizontal plutonium fluxes on airborne nonrespirable soils at all three sites were bracketed within the same four orders of magnitude from 10 -7 to 10 -3 μCi/(m 2 day) for 239 Pu and 10 -8 to 10 -5 μCi/(m 2 day) for 238 Pu. Airborne respirable 239 Pu concentrations increased with wind speed for a southwest wind direction coming from offsite near the Hanford reservation Prosser barricade. Airborne plutonium fluxes on nonrespirable particles had isotopic ratios, 240 Pu/ 239 240 Pu, similar to weapons grade plutonium rather than fallout plutonium

Research Note Topographical units and soil types prove more ...

African Journals Online (AJOL)

The floristic data (species presence at each site) were grouped into Land Types, topographical units and broad soil types. Each group was analysed independently using multivariate detrended correspondence analysis (DCA) and the mean similarity test. The floristic data in each Land Type showed a 42% range of ...

Modelling topographic potential for erosion and deposition using GIS

Science.gov (United States)

Helena Mitasova; Louis R. Iverson

1996-01-01

Modelling of erosion and deposition in complex terrain within a geographical information system (GIS) requires a high resolution digital elevation model (DEM), reliable estimation of topographic parameters, and formulation of erosion models adequate for digital representation of spatially distributed parameters. Regularized spline with tension was integrated within a...

Topographic attributes as a guide for automated detection or highlighting of geological features

Science.gov (United States)

Viseur, Sophie; Le Men, Thibaud; Guglielmi, Yves

2015-04-01

Photogrammetry or LIDAR technology combined with photography allow geoscientists to obtain 3D high-resolution numerical representations of outcrops, generally termed as Digital Outcrop Models (DOM). For over a decade, these 3D numerical outcrops serve as support for precise and accurate interpretations of geological features such as fracture traces or plans, strata, facies mapping, etc. These interpretations have the benefit to be directly georeferenced and embedded into the 3D space. They are then easily integrated into GIS or geomodeler softwares for modelling in 3D the subsurface geological structures. However, numerical outcrops generally represent huge data sets that are heavy to manipulate and hence to interpret. This may be particularly tedious as soon as several scales of geological features must be investigated or as geological features are very dense and imbricated. Automated tools for interpreting geological features from DOMs would be then a significant help to process these kinds of data. Such technologies are commonly used for interpreting seismic or medical data. However, it may be noticed that even if many efforts have been devoted to easily and accurately acquire 3D topographic point clouds and photos and to visualize accurate 3D textured DOMs, few attentions have been paid to the development of algorithms for automated detection of the geological structures from DOMs. The automatic detection of objects on numerical data generally assumes that signals or attributes computed from this data allows the recognition of the targeted object boundaries. The first step consists then in defining attributes that highlight the objects or their boundaries. For DOM interpretations, some authors proposed to use differential operators computed on the surface such as normal or curvatures. These methods generally extract polylines corresponding to fracture traces or bed limits. Other approaches rely on the PCA technology to segregate different topographic plans

Tropical Airborne LiDAR for Landslide Assessment in Malaysia: a technical perspective

Science.gov (United States)

Abd Manap, Mohamad; Azhari Razak, Khamarrul; Mohamad, Zakaria; Ahmad, Azhari; Ahmad, Ferdaus; Mohamad Zin, Mazlan; A'zad Rosle, Qalam

2015-04-01

Malaysia has faced a substantial number of landslide events every year. Cameron Highlands, Pahang is one of the badly areas affected by slope failures characterized by extreme climate, rugged topographic and weathered geological structures in a tropical environment. A high frequency of landslide occurrence in the hilly areas is predominantly due to the geological materials, tropical monsoon seasons and uncontrolled agricultural activities. Therefore the Government of Malaysia through the Prime Minister Department has allocated a special budget to conduct national level hazard and risk mapping project through Minerals and Geoscience Department Malaysia, the Ministry of Natural Resources and Environment. The primary aim of this project is to provide slope hazard risk information for a better slope management in Malaysia. In addition this project will establish national infrastructure for geospatial information on the geological terrain and slope by emphasizing the disaster risk throughout the country. The areas of interest are located in the three different selected areas i.e. Cameron Highlands (275 square kilometers), Ipoh (200 square kilometers) and Cheras Kajang -- Batang kali (650 square kilometers). These areas are selected based on National Slope Master Plan (2009 -- 2023) that endorsed by Malaysia Government Cabinet. The national hazard and risk mapping project includes six parts of major tasks: (1) desk study and mobilization, (2) airborne LiDAR data acquisition and analysis, (3) field data acquisition and verification, (4) hazard and risk for natural terrain, (5) hazard and risk analysis for man-made slope and (6) Man-made slope mitigation/preventive measures. The project was authorized in September, 2014 and will be ended in March, 2016. In this paper, the main focus is to evaluate the suitability of integrated capability of airborne- and terrestrial LiDAR data acquisition and analysis, and also digital photography for regional landslide assessment. The

Optimization of Structural Design for Sustainable Construction of Transmission Tower Based on Topographical Algorithm

International Nuclear Information System (INIS)

Muda, Zakaria Che; Thiruchelvam, Sivadass; Mustapha, Kamal Nasharuddin; Omar, Rohayu Che; Usman, Fathoni; Alam, Md Ashrafu

2013-01-01

Optimization of transmission tower structures is traditionally based on either optimization of members sizes with fixed topographical shape or based on structural analysis modelling strategies without taking cognizance of fabrication and constructability issue facing the contractors . This paper look into an integrated optimum design approach strategies whereby size, shape and topology are combined together with the fabrication issues in the construction of the transmission tower. The topographical algorithm is based on changing the inclination degree of the legs of the tower at first with optimum individual members sizing and later rationalized member sizes are performed through member groupings for the ease fabrication and construction of the transmission tower. The optimum weight using topographical algorithm obtained for the transmission tower is 10,924 kg for singular members and 18,430 kg for element grouping at 10° inclination angle.

Airborne Precursors Predict Maternal Serum Perfluoroalkyl Acid Concentrations.

Science.gov (United States)

Makey, Colleen M; Webster, Thomas F; Martin, Jonathan W; Shoeib, Mahiba; Harner, Tom; Dix-Cooper, Linda; Webster, Glenys M

2017-07-05

Human exposure to persistent perfluoroalkyl acids (PFAAs), including perfluorooctanoic acid (PFOA), perfluorononanoic acid (PFNA), and perfluorooctanesulfonate (PFOS), can occur directly from contaminated food, water, air, and dust. However, precursors to PFAAs (PreFAAs), such as dipolyfluoroalkyl phosphates (diPAPs), fluorotelomer alcohols (FTOHs), perfluorooctyl sulfonamides (FOSAs), and sulfonamidoethanols (FOSEs), which can be biotransformed to PFAAs, may also be a source of exposure. PFAAs were analyzed in 50 maternal sera samples collected in 2007-2008 from participants in Vancouver, Canada, while PFAAs and PreFAAs were measured in matching samples of residential bedroom air collected by passive sampler and in sieved vacuum dust (<150 μm). Concentrations of PreFAAs were higher than for PFAAs in air and dust. Positive associations were discovered between airborne 10:2 FTOH and serum PFOA and PFNA and between airborne MeFOSE and serum PFOS. On average, serum PFOS concentrations were 2.3 ng/mL (95%CI: 0.40, 4.3) higher in participants with airborne MeFOSE concentrations in the highest tertile relative to the lowest tertile. Among all PFAAs, only PFNA in air and vacuum dust predicted serum PFNA. Results suggest that airborne PFAA precursors were a source of PFOA, PFNA, and PFOS exposure in this population.

Modelling airborne dispersion of coarse particulate material

International Nuclear Information System (INIS)

Apsley, D.D.

1989-03-01

Methods of modelling the airborne dispersion and deposition of coarse particulates are presented, with the emphasis on the heavy particles identified as possible constituents of releases from damaged AGR fuel. The first part of this report establishes the physical characteristics of the irradiated particulate in airborne emissions from AGR stations. The second part is less specific and describes procedures for extending current dispersion/deposition models to incorporate a coarse particulate component: the adjustment to plume spread parameters, dispersion from elevated sources and dispersion in conjunction with building effects and plume rise. (author)

Topographic mapping support in the South African military during the

African Journals Online (AJOL)

andre

In doing so, the operational importance of topographic maps is also ...... Police and later the South African Defence Force tried to stem this growing tide and ... first annual intake of national service women, and though trained internally as.

Polar gravity fields from GOCE and airborne gravity

DEFF Research Database (Denmark)

Forsberg, René; Olesen, Arne Vestergaard; Yidiz, Hasan

2011-01-01

Airborne gravity, together with high-quality surface data and ocean satellite altimetric gravity, may supplement GOCE to make consistent, accurate high resolution global gravity field models. In the polar regions, the special challenge of the GOCE polar gap make the error characteristics...... of combination models especially sensitive to the correct merging of satellite and surface data. We outline comparisons of GOCE to recent airborne gravity surveys in both the Arctic and the Antarctic. The comparison is done to new 8-month GOCE solutions, as well as to a collocation prediction from GOCE gradients...... in Antarctica. It is shown how the enhanced gravity field solutions improve the determination of ocean dynamic topography in both the Arctic and in across the Drake Passage. For the interior of Antarctica, major airborne gravity programs are currently being carried out, and there is an urgent need...

A metagenomic framework for the study of airborne microbial communities.

Science.gov (United States)

Yooseph, Shibu; Andrews-Pfannkoch, Cynthia; Tenney, Aaron; McQuaid, Jeff; Williamson, Shannon; Thiagarajan, Mathangi; Brami, Daniel; Zeigler-Allen, Lisa; Hoffman, Jeff; Goll, Johannes B; Fadrosh, Douglas; Glass, John; Adams, Mark D; Friedman, Robert; Venter, J Craig

2013-01-01

Understanding the microbial content of the air has important scientific, health, and economic implications. While studies have primarily characterized the taxonomic content of air samples by sequencing the 16S or 18S ribosomal RNA gene, direct analysis of the genomic content of airborne microorganisms has not been possible due to the extremely low density of biological material in airborne environments. We developed sampling and amplification methods to enable adequate DNA recovery to allow metagenomic profiling of air samples collected from indoor and outdoor environments. Air samples were collected from a large urban building, a medical center, a house, and a pier. Analyses of metagenomic data generated from these samples reveal airborne communities with a high degree of diversity and different genera abundance profiles. The identities of many of the taxonomic groups and protein families also allows for the identification of the likely sources of the sampled airborne bacteria.

South African Airborne Operations

African Journals Online (AJOL)

South Africa carried out numerous airborne operations during the latter part .... It was a lesson the French had learned and were learning in Indo-China and ..... South African government, concerned that the conflict would spill across their northern border, ...... the Super Frelon and it was an outstanding helicopter at sea level.

Characteristics of airborne plutonium resuspended from near-background aged surface-sources

International Nuclear Information System (INIS)

Sehmel, G.A.

1982-11-01

Plutonium content in samples of airborne solids collected at five Hanford sites was determined in several experiments directed toward investigating resuspension processes for aged surface sources. Though airborne plutonium concentrations are extremely low, radiochemical technique sensitivities allow plutonium characterization to be considered as a function of host-particle diameter in samples of airborne solids. Plutonium concentrations and activity densities are a function of aerodynamic particle diameter, sampling height, wind speed, wind direction and plutonium isotopic ratios

Stereo Pair, with Topographic Height as Color, Manicouagan Crater, Quebec, Canada

Science.gov (United States)

2003-01-01

Manicouagan Crater is one of the world's largest and oldest known impact craters and perhaps the one most readily apparent to astronauts in orbit. The age of the impact is estimated at 214 million years before present. Since then erosion has removed about one kilometer (0.6 miles) of rock from the region and has created a topographic pattern that follows the structural pattern of the crater. A ring depression (prominently seen as green) encloses a central peak. The ring depression now hosts the Manicouagan Reservoir and so appears as a distinct ring lake to astronauts and as a smooth and flat feature in this topographic visualization. A fine pattern of topographic striations trending south-southeast, most prominent within the crater itself, indicates the flow direction of glaciers that covered this area during the last ice age. Three visualization methods were combined to produce this image: shading, color coding, and synthetic stereoscopy. The shade image was derived by computing topographic slope in the north-south direction. Northern slopes appear bright and southern slopes appear dark. Color coding is directly related to topographic height, with green at the lower elevations, rising through yellow, red, and magenta, to blue at the highest elevations. The stereoscopic effect was then created by generating two differing perspectives, one for each eye. The image can be seen in 3-D by viewing the left image with the right eye and the right image with the left eye (cross-eyed viewing) or by downloading, printing, and splitting the image pair and viewing them with a stereoscope. When stereoscopically merged, the result is a vertically exaggerated view of Earth's surface in its full three dimensions. Total topographic relief from the ring lake level to the central crater peak is about 600 meters (2000 feet). Elevation data used in this image were acquired by the Shuttle Radar Topography Mission aboard the Space Shuttle Endeavour, launched on February 11, 2000. The

Variations of airborne and waterborne Rn-222 in houses in Maine

Energy Technology Data Exchange (ETDEWEB)

Hess, C.T.; Weiffenbach, C.V.; Norton, S.A. (Maine Univ., Orono (USA))

1982-01-01

Concentrations of airborne radon ranging from 0.05 to 135 pCi/L were found in houses in Maine. To investigate the association between elevated radon concentrations in well water and the indoor airborne radon concentrations, the radon in the water supplies of these houses was measured by liquid scintillation. Monitors of airborne radon were used for dynamic studies in 18 houses, determining the component of airborne radon associated with showers, laundry and dishwashing, which liberate radon in bursts. The component of airborne radon associated with water sources was found to vary inversely with ventilation rate and directly with waterborne radon concentration, with 0.8 +- 0.2 pCi Rn/L air per nCi Rn/L water at a ventilation rate of 1.0 air change per hour. The data are pertinent to a study which has revealed significant correlations between county averages, from the National Cancer Institute, or age-adjusted cancer mortality rates in Maine and average values of radon concentrations in water for the counties.

Variations of airborne and waterborne Rn-222 in houses in Maine

International Nuclear Information System (INIS)

Hess, C.T.; Weiffenbach, C.V.; Norton, S.A.

1982-01-01

Concentrations of airborne radon ranging from 0.05 to 135 pCi/L were found in houses in Maine. To investigate the association between elevated radon concentrations in well water and the indoor airborne radon concentrations, the radon in the water supplies of these houses was measured by liquid scintillation. Monitors of airborne radon were used for dynamic studies in 18 houses, determining the component of airborne radon associated with showers, laundry and dishwashing, which liberate radon in bursts. The component of airborne radon associated with water sources was found to vary inversely with ventilation rate and directly with waterborne radon concentration, with 0.8 +- 0.2 pCi Rn/L air per nCi Rn/L water at a ventilation rate of 1.0 air change per hour. The data are pertinent to a study which has revealed significant correlations between county averages, from the National Cancer Institute, or age-adjusted cancer mortality rates in Maine and average values of radon concentrations in water for the counties. (author)

Topographical memory analyzed in mice using the Hamlet test, a novel complex maze.

Science.gov (United States)

Crouzier, Lucie; Gilabert, Damien; Rossel, Mireille; Trousse, Françoise; Maurice, Tangui

2018-03-01

The Hamlet test is an innovative device providing a complex environment for testing topographic memory in mice. Animals were trained in groups for weeks in a small village with a central agora, streets expanding from it towards five functionalized houses, where they can drink, eat, hide, run, interact with a stranger mouse. Memory was tested by depriving mice from water or food and analyzing their ability to locate the Drink/Eat house. Exploration and memory were analyzed in different strains, gender, and after different training periods and delays. After 2 weeks training, differences in exploration patterns were observed between strains, but not gender. Neuroanatomical structures activated by training, identified using FosB/ΔFosB immunolabelling, showed an involvement of the hippocampus-subiculum-parahippocampal gyrus axis and dopaminergic structures. Training increased hippocampal neurogenesis (cell proliferation and neuronal maturation) and modified the amnesic efficacy of muscarinic or nicotinic cholinergic antagonists. Moreover, topographical disorientation in Alzheimer's disease was addressed using intracerebroventricular injection of amyloid β 25-35 peptide in trained mice. When retested after 7 days, Aβ 25-35 -treated mice showed memory impairment. The Hamlet test specifically allows analysis of topographical memory in mice, based on complex environment. It offers an innovative tool for various ethological or pharmacological research needs. For instance, it allowed to examine topographical disorientation, a warning sign in Alzheimer's disease. Copyright © 2018 Elsevier Inc. All rights reserved.

Plutonium concentrations in airborne soil at Rocky Flats and Hanford determined during resuspension experiments

Energy Technology Data Exchange (ETDEWEB)

Sehmel, G.A.

1978-01-01

Plutonium resuspension results are summarized for experiments conducted by the author at Rocky Flats, onsite on the Hanford reservation, and for winds blowing from offsite onto the Hanford reservation near the Prosser barricade boundary. In each case, plutonium resuspension was shown by increased airborne plutonium concentrations as a function of either wind speed or as compared to fallout levels. All measured airborne concentrations were far below maximum permissible concentrations (MPC). Both plutonium and cesium concentrations on airborne soil were normalized by the quantity of airborne soil sampled. Airborne radionuclide concentrations in ..mu..Ci/g were related to published values for radionuclide concentrations on surface soils. For this ratio of radionuclide concentration per gram on airborne soil divided by that for ground surface soil, there are eight orders of magnitude uncertainty from 10/sup -4/ to 10/sup 4/. This uncertainty in the equality between plutonium concentrations per gram on airborne and surface soils is caused by only a fraction of the collected airborne soil being transported from offsite rather than all being resuspended from each study site and also by the great variabilities in surface contamination. Horizontal plutonium fluxes on airborne nonrespirable soils at all three sites were bracketed within the same four orders of magnitude from 10/sup -7/ to 10/sup -3/ ..mu..Ci/(m/sup 2/ day) for /sup 239/Pu and 10/sup -8/ to 10/sup -5/ ..mu..Ci/(m/sup 2/ day) for /sup 238/Pu. Airborne respirable /sup 239/Pu concentrations increased with wind speed for a southwest wind direction coming from offsite near the Hanford reservation Prosser barricade. Airborne plutonium fluxes on nonrespirable particles had isotopic ratios, /sup 240/Pu//sup 239/ /sup 240/Pu, similar to weapons grade plutonium rather than fallout plutonium.

Elevational Shifts in the Topographic Position of Polylepis Forest Stands in the Andes of Southern Peru

Directory of Open Access Journals (Sweden)

Johanna M. Toivonen

2017-12-01

Full Text Available The patchy distribution of high-Andean treeline forests has provoked discussion about the relative importance of anthropogenic and climatic causes of this pattern, both of which vary with topography. We aimed to understand the topographic controls on the distribution of Polylepis subsericans treeline forests in the Andes of southern Peru, and the changes in these controls along an elevational gradient. We mapped Polylepis forests in the Cordillera Urubamba, Cusco, using high-resolution aerial images and related forest cover to topographic variables extracted from a digital terrain model (30-m resolution. The variables were selected based on their expected biological relevance for tree growth at high elevations. We constructed logistic regression models of forest cover, separately for each of five 100-m elevational belts. To deal with spatial autocorrelation, models were based on randomized 10% subsampling of the data with 1000 repetitions. The results suggest a consistent shift in topographic preference with elevation, with forests at lower elevations showing a preference for topographically protected sites near rivers and forests at higher elevations being increasingly restricted to north-facing and well-drained sites. Our study offers the first indication of the ability of Andean treeline forests to benefit from the topographic heterogeneity of the high-Andes. Providing that dispersal and establishment are possible, local relocation between microsites could help these forests to persist regionally in spite of changing climatic conditions.

Airborne and food sensitization patterns in children and adults with eosinophilic esophagitis.

Science.gov (United States)

He, Yu Ting; Christos, Paul J; Reisacher, William R

2018-05-01

The pathogenesis of eosinophilic esophagitis (EoE) is currently unknown, but evidence suggests that allergic sensitization to food and airborne allergens may play a key role. This retrospective study examines the rate of sensitization to both food and airborne allergens in EoE patients, and compares their sensitivity patterns to control groups. We identified 103 patients with a diagnosis of EoE via esophageal eosinophilia (≥15 eosinophils/high-power field [hpf]), who had undergone comprehensive food and/or airborne allergen testing through either skin or in vitro methods. Food and airborne allergen sensitization was defined as positive testing in at least 1 food subgroup (milk, peanut, tree nut, seafood/fish, soy, grain, egg) or airborne subgroup (tree, grass, weed, mite/cockroach, animal, mold), respectively. The same sensitization criterion was applied to allergic rhinitis (AR) patients, with and without a clinical suspicion of food allergy (FA), in order to create control groups. Sensitization in the EoE group to at least 1 subgroup of food allergen and airborne allergen was seen in 77.1% (64/83) and 71.7% (38/53), respectively (p = 0.82). There were significant differences in sensitization between EoE and control groups for tree nut, soy, grain, and egg, but no differences noted in any of the other food or airborne allergen subgroups, even after accounting for age and gender. EoE and control groups had similar airborne allergen sensitization patterns, yet dissimilar food allergen sensitization patterns, suggesting that specific allergens may play a more prominent role in the pathogenesis of EoE. The EoE group had a more uniform distribution pattern for food allergens, compared to controls. © 2018 ARS-AAOA, LLC.

Challenges and Opportunities of Airborne Metagenomics

KAUST Repository

Behzad, H.; Gojobori, Takashi; Mineta, K.

2015-01-01

microorganisms. Airborne metagenomic studies could also lead to discoveries of novel genes and metabolic pathways relevant to meteorological and industrial applications, environmental bioremediation, and biogeochemical cycles.

Airborne particulate matter in spacecraft

Science.gov (United States)

1988-01-01

Acceptability limits and sampling and monitoring strategies for airborne particles in spacecraft were considered. Based on instances of eye and respiratory tract irritation reported by Shuttle flight crews, the following acceptability limits for airborne particles were recommended: for flights of 1 week or less duration (1 mg/cu m for particles less than 10 microns in aerodynamic diameter (AD) plus 1 mg/cu m for particles 10 to 100 microns in AD); and for flights greater than 1 week and up to 6 months in duration (0.2 mg/cu m for particles less than 10 microns in AD plus 0.2 mg/cu m for particles 10 to 100 microns in AD. These numerical limits were recommended to aid in spacecraft atmosphere design which should aim at particulate levels that are a low as reasonably achievable. Sampling of spacecraft atmospheres for particles should include size-fractionated samples of 0 to 10, 10 to 100, and greater than 100 micron particles for mass concentration measurement and elementary chemical analysis by nondestructive analysis techniques. Morphological and chemical analyses of single particles should also be made to aid in identifying airborne particulate sources. Air cleaning systems based on inertial collection principles and fine particle collection devices based on electrostatic precipitation and filtration should be considered for incorporation into spacecraft air circulation systems. It was also recommended that research be carried out in space in the areas of health effects and particle characterization.

Reconstucted topographs of polycrystalline (110) Fe-3 wt% Si samples and the observation of their magnetic domain images using synchrotron radiation

International Nuclear Information System (INIS)

Stephenson, J.D.; Kelhae, V.; Tilli, M.; Tuomi, T.

1978-01-01

'White' synchrotron radiation topography has been employed to reconstruct almost complete, though slightly shape distorted topographs of polycrystalline samples. Those used in the experiments were commercial (110) Fe-3wt%Si crystals containing several misorientated subgrains and were of thickness between 0.15 and 0.20 mm. The topographs were reassembled 'jig-saw puzzle' fashion from photographically enlarged subgrain mini-topographs located near the centres of each film. Magnetic domains were observed in several subgrain topographs recorded in the Laue-reflection and Laue-transmission modes. The technique emphasizes one of the advantages in using 'white' synchrotron radiation to produce rapid high resolution topographs of polycrystalline samples in relatively hazard free radiation conditions. (Auth.)

Comparison Between Topographic Expression of RADARSAT and DEM in Simpang Pulai to Pos Selim, Malaysia

Directory of Open Access Journals (Sweden)

M.F.Ramli

2010-01-01

Full Text Available Radar and digital elevation model had been utilised in many structural studies. The main objective of this study is to compare the RADARSAT and digital elevation model for lineament interpretation which probably represent the main joints or faults along the Simpang Pulai to Pos Selim highway, Malaysia. These joints and faults may influence the instability along the highway. Manual comparison in terms of topographical aspect was undertaken between RADARSAT with 25 m spatial resolution and digital elevation model derived from 20 m contour interval of the topographical map. The previously interpreted lineaments of more than 2 km in the study area was draped over the RADARSAT and digital elevation model to compared whether the lineament concurred with the topographical representation. The interpreted lineaments were derived from Landsat TM of 1990 and 2002, where the DEM had been utilised in the negative lineament determination. It is concluded that the application RADARSAT is not very useful in terms of topographical expression in the structural geological interpretation for the study area compared to DEM derived from contour data. Further work is suggested before any conclusion can be confidently derived.

STM topographical images of C60

International Nuclear Information System (INIS)

Wang, Z.; Zhang, P.; Moskovits, M.

1991-01-01

In this paper STM topographical images of C 60 are reported. The images are consistent with a molecule approximately 9 Angstrom in diameter possessing the now-famous soccer ball structure. With the molecule deposited on gold, its atomic structure is not resolved. On graphite the structure of the within the borders of the C 60 molecule is dominated by that of the graphite forming a moire-like pattern. Some evidence of atomic structure is seen in multilayers of C 60 where some five- and six-membered rings are visible. These may, however, be features of fragments of the fullerene rather than whole molecules

Airborne pollen trends in the Iberian Peninsula.

Science.gov (United States)

Galán, C; Alcázar, P; Oteros, J; García-Mozo, H; Aira, M J; Belmonte, J; Diaz de la Guardia, C; Fernández-González, D; Gutierrez-Bustillo, M; Moreno-Grau, S; Pérez-Badía, R; Rodríguez-Rajo, J; Ruiz-Valenzuela, L; Tormo, R; Trigo, M M; Domínguez-Vilches, E

2016-04-15

Airborne pollen monitoring is an effective tool for studying the reproductive phenology of anemophilous plants, an important bioindicator of plant behavior. Recent decades have revealed a trend towards rising airborne pollen concentrations in Europe, attributing these trends to an increase in anthropogenic CO2 emissions and temperature. However, the lack of water availability in southern Europe may prompt a trend towards lower flowering intensity, especially in herbaceous plants. Here we show variations in flowering intensity by analyzing the Annual Pollen Index (API) of 12 anemophilous taxa across 12 locations in the Iberian Peninsula, over the last two decades, and detecting the influence of the North Atlantic Oscillation (NAO). Results revealed differences in the distribution and flowering intensity of anemophilous species. A negative correlation was observed between airborne pollen concentrations and winter averages of the NAO index. This study confirms that changes in rainfall in the Mediterranean region, attributed to climate change, have an important impact on the phenology of plants. Copyright © 2016 Elsevier B.V. All rights reserved.

Accuracy of topographic index models at identifying ephemeral gully trajectories on agricultural fields

Science.gov (United States)

Sheshukov, Aleksey Y.; Sekaluvu, Lawrence; Hutchinson, Stacy L.

2018-04-01

Topographic index (TI) models have been widely used to predict trajectories and initiation points of ephemeral gullies (EGs) in agricultural landscapes. Prediction of EGs strongly relies on the selected value of critical TI threshold, and the accuracy depends on topographic features, agricultural management, and datasets of observed EGs. This study statistically evaluated the predictions by TI models in two paired watersheds in Central Kansas that had different levels of structural disturbances due to implemented conservation practices. Four TI models with sole dependency on topographic factors of slope, contributing area, and planform curvature were used in this study. The observed EGs were obtained by field reconnaissance and through the process of hydrological reconditioning of digital elevation models (DEMs). The Kernel Density Estimation analysis was used to evaluate TI distribution within a 10-m buffer of the observed EG trajectories. The EG occurrence within catchments was analyzed using kappa statistics of the error matrix approach, while the lengths of predicted EGs were compared with the observed dataset using the Nash-Sutcliffe Efficiency (NSE) statistics. The TI frequency analysis produced bi-modal distribution of topographic indexes with the pixels within the EG trajectory having a higher peak. The graphs of kappa and NSE versus critical TI threshold showed similar profile for all four TI models and both watersheds with the maximum value representing the best comparison with the observed data. The Compound Topographic Index (CTI) model presented the overall best accuracy with NSE of 0.55 and kappa of 0.32. The statistics for the disturbed watershed showed higher best critical TI threshold values than for the undisturbed watershed. Structural conservation practices implemented in the disturbed watershed reduced ephemeral channels in headwater catchments, thus producing less variability in catchments with EGs. The variation in critical thresholds for all

Fine-resolution repeat topographic surveying of dryland landscapes using UAS-based structure-from-motion photogrammetry: Assessing accuracy and precision against traditional ground-based erosion measurements

Science.gov (United States)

Gillian, Jeffrey K.; Karl, Jason W.; Elaksher, Ahmed; Duniway, Michael C.

2017-01-01

Structure-from-motion (SfM) photogrammetry from unmanned aerial system (UAS) imagery is an emerging tool for repeat topographic surveying of dryland erosion. These methods are particularly appealing due to the ability to cover large landscapes compared to field methods and at reduced costs and finer spatial resolution compared to airborne laser scanning. Accuracy and precision of high-resolution digital terrain models (DTMs) derived from UAS imagery have been explored in many studies, typically by comparing image coordinates to surveyed check points or LiDAR datasets. In addition to traditional check points, this study compared 5 cm resolution DTMs derived from fixed-wing UAS imagery with a traditional ground-based method of measuring soil surface change called erosion bridges. We assessed accuracy by comparing the elevation values between DTMs and erosion bridges along thirty topographic transects each 6.1 m long. Comparisons occurred at two points in time (June 2014, February 2015) which enabled us to assess vertical accuracy with 3314 data points and vertical precision (i.e., repeatability) with 1657 data points. We found strong vertical agreement (accuracy) between the methods (RMSE 2.9 and 3.2 cm in June 2014 and February 2015, respectively) and high vertical precision for the DTMs (RMSE 2.8 cm). Our results from comparing SfM-generated DTMs to check points, and strong agreement with erosion bridge measurements suggests repeat UAS imagery and SfM processing could replace erosion bridges for a more synoptic landscape assessment of shifting soil surfaces for some studies. However, while collecting the UAS imagery and generating the SfM DTMs for this study was faster than collecting erosion bridge measurements, technical challenges related to the need for ground control networks and image processing requirements must be addressed before this technique could be applied effectively to large landscapes.

Detection of coastal and submarine discharge on the Florida Gulf Coast with an airborne thermal-infrared mapping system

Science.gov (United States)

Raabe, Ellen; Stonehouse, David; Ebersol, Kristin; Holland, Kathryn; Robbins, Lisa

2011-01-01

Along the Gulf Coast of Florida north of Tampa Bay lies a region characterized by an open marsh coast, low topographic gradient, water-bearing limestone, and scattered springs. The Floridan aquifer system is at or near land surface in this region, discharging water at a consistent 70-72°F. The thermal contrast between ambient water and aquifer discharge during winter months can be distinguished using airborne thermal-infrared imagery. An airborne thermal-infrared mapping system was used to collect imagery along 126 miles of the Gulf Coast from Jefferson to Levy County, FL, in March 2009. The imagery depicts a large number of discharge locations and associated warm-water plumes in ponds, creeks, rivers, and nearshore waters. A thermal contrast of 6°F or more was set as a conservative threshold for identifying sites, statistically significant at the 99% confidence interval. Almost 900 such coastal and submarine-discharge locations were detected, averaging seven to nine per mile along this section of coast. This represents approximately one hundred times the number of previously known discharge sites in the same area. Several known coastal springs in Taylor and Levy Counties were positively identified with the imagery and were used to estimate regional discharge equivalent to one 1st-order spring, discharging 100 cubic feet per second or more, for every two miles of coastline. The number of identified discharge sites is a conservative estimate and may represent two-thirds of existing features due to low groundwater levels at time of overflight. The role of aquifer discharge in coastal and estuarine health is indisputable; however, mapping and quantifying discharge in a complex karst environment can be an elusive goal. The results of this effort illustrate the effectiveness of the instrument and underscore the influence of coastal springs along this stretch of the Florida coast.

Why Gas Hydrate Occurrenced Over Topographic Highs in Shenhu Area Northern South China Sea？

Science.gov (United States)

Liao, J.

2015-12-01

Methane gas hydrate has been drilled by China Geological Survey in shenhu area northern south china sea in 2007 .Shenhu area is located in the middle-lower continental slope and 17 submarine canyons are incised into the shelf,gas hydrtae was observed in boreholes over topographic highs,but origin of the hydrate is controversial.Accumulation of gas hydrate is depending on temperature-pressure field and supply quantities of methane and some other factors,in the same depth of the shallow sediments there is the same press,so temperature field and supply quantities of methane become the most important factors.Lachenbruch(1968) calculated the topographic disturbance to geothermal gradients,in shenhu area consistent local variations were observed, notably low heat flow values over prominent topographic highs and high heat flow values over the flanks of the topographic highs. At some localities over a horizontal distance of 2.5 km, heat flow increased by as much as 50%, from typical values of 65 to 100 mW/m2 .Some vertical fractures were observed beneath topographic highs in previous studies.Based on the profile across borehole SH7,we designed four experiments:A,uniform distribution of heat flux with no vertical fractures；B,Uniform distribution of heat flux with vertical fractures beneath geographic highs;C,uneven distribution of heat flux with no vertical fractures;D,uneven distribution of heat flux with vertical fractures beneath geographic highs.According to previous studies,we restored Palaeobathymetry,abundance of organic matters, sandstone-madstone ratio ,porosity and permeability of each,and parameters of vertical fractures.The result of experiment D shows the similar distribution characteristic with the drilling result,so We believe that low heat flux and Vertical fractures are the most important factors . This work was supported by the National Science Foundation of China(grant no. 41406080).

Assessing the impact of different sources of topographic data on 1-D hydraulic modelling of floods

Science.gov (United States)

Ali, A. Md; Solomatine, D. P.; Di Baldassarre, G.

2015-01-01

Topographic data, such as digital elevation models (DEMs), are essential input in flood inundation modelling. DEMs can be derived from several sources either through remote sensing techniques (spaceborne or airborne imagery) or from traditional methods (ground survey). The Advanced Spaceborne Thermal Emission and Reflection Radiometer (ASTER), the Shuttle Radar Topography Mission (SRTM), the light detection and ranging (lidar), and topographic contour maps are some of the most commonly used sources of data for DEMs. These DEMs are characterized by different precision and accuracy. On the one hand, the spatial resolution of low-cost DEMs from satellite imagery, such as ASTER and SRTM, is rather coarse (around 30 to 90 m). On the other hand, the lidar technique is able to produce high-resolution DEMs (at around 1 m), but at a much higher cost. Lastly, contour mapping based on ground survey is time consuming, particularly for higher scales, and may not be possible for some remote areas. The use of these different sources of DEM obviously affects the results of flood inundation models. This paper shows and compares a number of 1-D hydraulic models developed using HEC-RAS as model code and the aforementioned sources of DEM as geometric input. To test model selection, the outcomes of the 1-D models were also compared, in terms of flood water levels, to the results of 2-D models (LISFLOOD-FP). The study was carried out on a reach of the Johor River, in Malaysia. The effect of the different sources of DEMs (and different resolutions) was investigated by considering the performance of the hydraulic models in simulating flood water levels as well as inundation maps. The outcomes of our study show that the use of different DEMs has serious implications to the results of hydraulic models. The outcomes also indicate that the loss of model accuracy due to re-sampling the highest resolution DEM (i.e. lidar 1 m) to lower resolution is much less than the loss of model accuracy due

Methods of sampling airborne fungi in working environments of waste treatment facilities.

Science.gov (United States)

Černá, Kristýna; Wittlingerová, Zdeňka; Zimová, Magdaléna; Janovský, Zdeněk

2016-01-01

The objective of the present study was to evaluate and compare the efficiency of a filter based sampling method and a high volume sampling method for sampling airborne culturable fungi present in waste sorting facilities. Membrane filters method was compared with surface air system method. The selected sampling methods were modified and tested in 2 plastic waste sorting facilities. The total number of colony-forming units (CFU)/m3 of airborne fungi was dependent on the type of sampling device, on the time of sampling, which was carried out every hour from the beginning of the work shift, and on the type of cultivation medium (p airborne fungi ranged 2×102-1.7×106 CFU/m3 when using the membrane filters (MF) method, and 3×102-6.4×104 CFU/m3 when using the surface air system (SAS) method. Both methods showed comparable sensitivity to the fluctuations of the concentrations of airborne fungi during the work shifts. The SAS method is adequate for a fast indicative determination of concentration of airborne fungi. The MF method is suitable for thorough assessment of working environment contamination by airborne fungi. Therefore we recommend the MF method for the implementation of a uniform standard methodology of airborne fungi sampling in working environments of waste treatment facilities. This work is available in Open Access model and licensed under a CC BY-NC 3.0 PL license.

Characteristics of airborne micro-organisms in a neurological intensive care unit: Results from China.

Science.gov (United States)

Yu, Yao; Yin, Sufeng; Kuan, Yi; Xu, Yingjun; Gao, Xuguang

2015-06-01

To describe the characteristics of airborne micro-organisms in the environment in a Chinese neurological intensive care unit (NICU). This prospective study monitored the air environment in two wards (large and small) of an NICU in a tertiary hospital in China for 12 months, using an LWC-1 centrifugal air sampler. Airborne micro-organisms were identified using standard microbiology techniques. The mean ± SD number of airborne bacteria was significantly higher in the large ward than in the small ward (200 ± 51 colony-forming units [CFU]/m(3) versus 110 ± 40 CFU/m(3), respectively). In the large ward only, the mean number of airborne bacteria in the autumn was significantly higher than in any of the other three seasons. A total of 279 airborne micro-organisms were identified (large ward: 195; small ward: 84). There was no significant difference in the type and distribution of airborne micro-organisms between the large and small wards. The majority of airborne micro-organisms were Gram-positive cocci in both wards. These findings suggest that the number of airborne micro-organisms was related to the number of patients on the NICU ward. © The Author(s) 2015 Reprints and permissions: sagepub.co.uk/journalsPermissions.nav.

MGN V RDRS 5 GLOBAL DATA RECORD TOPOGRAPHIC V1.0

Data.gov (United States)

National Aeronautics and Space Administration — This data set contains the Magellan Global Topographic Data Record (GTDR). The range to surface is derived by fitting altimeter echoes from the fan-beam altimetry...

Validation of meter-scale surface faulting offset measurements from high-resolution topographic data

Science.gov (United States)

Salisbury, Barrett; Haddad, D.E.; Rockwell, T.K.; Arrowsmith, R.; Madugo, C.; Zielke, O.; Scharer, Katherine M.

2015-01-01

Studies of active fault zones have flourished with the availability of high-resolution topographic data, particularly where airborne light detection and ranging (lidar) and structure from motion (SfM) data sets provide a means to remotely analyze submeter-scale fault geomorphology. To determine surface offset at a point along a strike-slip earthquake rupture, geomorphic features (e.g., stream channels) are measured days to centuries after the event. Analysis of these and cumulatively offset features produces offset distributions for successive earthquakes that are used to understand earthquake rupture behavior. As researchers expand studies to more varied terrain types, climates, and vegetation regimes, there is an increasing need to standardize and uniformly validate measurements of tectonically displaced geomorphic features. A recently compiled catalog of nearly 5000 earthquake offsets across a range of measurement and reporting styles provides insight into quality rating and uncertainty trends from which we formulate best-practice and reporting recommendations for remote studies. In addition, a series of public and beginner-level studies validate the remote methodology for a number of tools and emphasize considerations to enhance measurement accuracy and precision for beginners and professionals. Our investigation revealed that (1) standardizing remote measurement methods and reporting quality rating schemes is essential for the utility and repeatability of fault-offset measurements; (2) measurement discrepancies often involve misinterpretation of the offset geomorphic feature and are a function of the investigator’s experience; (3) comparison of measurements made by a single investigator in different climatic regions reveals systematic differences in measurement uncertainties attributable to variation in feature preservation; (4) measuring more components of a displaced geomorphic landform produces more consistently repeatable estimates of offset; and (5

Validation of meter-scale surface faulting offset measurements from high-resolution topographic data

KAUST Repository

Salisbury, J. Barrett

2015-10-24

Studies of active fault zones have flourished with the availability of high-resolution topographic data, particularly where airborne light detection and ranging (lidar) and structure from motion (SfM) data sets provide a means to remotely analyze submeter- scale fault geomorphology. To determine surface offset at a point along a strike-slip earthquake rupture, geomorphic features (e.g., stream channels) are measured days to centuries after the event. Analysis of these and cumulatively offset features produces offset distributions for successive earthquakes that are used to understand earthquake rupture behavior. As researchers expand studies to more varied terrain types, climates, and vegetation regimes, there is an increasing need to standardize and uniformly validate measurements of tectonically displaced geomorphic features. A recently compiled catalog of nearly 5000 earthquake offsets across a range of measurement and reporting styles provides insight into quality rating and uncertainty trends from which we formulate best-practice and reporting recommendations for remote studies. In addition, a series of public and beginner-level studies validate the remote methodology for a number of tools and emphasize considerations to enhance measurement accuracy and precision for beginners and professionals. Our investigation revealed that (1) standardizing remote measurement methods and reporting quality rating schemes is essential for the utility and repeatability of fault-offset measurements; (2) measurement discrepancies often involve misinterpretation of the offset geomorphic feature and are a function of the investigator\\'s experience; (3) comparison of measurements made by a single investigator in different climatic regions reveals systematic differences in measurement uncertainties attributable to variation in feature preservation; (4) measuring more components of a displaced geomorphic landform produces more consistently repeatable estimates of offset; and (5

Practical Consideration Factors to Design Array Configuration of Direction Finding System for Airborne Signal Intelligence

Directory of Open Access Journals (Sweden)

Jong-Hwan Lee

2018-01-01

Full Text Available Airborne signal intelligence (SIGINT systems must be capable of locating radio signal sources. Direction finding (DF to support this capability is an important factor. There are some practical considerations to be taken when designing the array configuration of a DF system for airborne SIGINT systems. This paper summarizes the practical factors when designing the array configuration of the DF system for airborne SIGINT. In particular, it focuses on four areas: antenna consideration factors when installing the DF system for airborne SIGINT from a practical point of view, array configuration methods for airborne communications intelligence and electronic intelligence, and a numerical analysis to select the optimum antenna position for airborne SIGINT.

Ears and Eyes in the Sky: The Evolution of Manned Airborne ISR

Science.gov (United States)

2012-05-25

immeasurably grateful. I would be remiss not to mention Mr. Larry Tart. His work on manned airborne ISR has educated and inspired the latest...comprehensive summary of airborne ISR such as that presented in this thesis. Several prominent works contain significant sections on airborne ISR. Larry ...Historic Cryptographic Collection, RG 457, Box 1369, NARA. 77 William E. Burrows , By Any Means Necessary (New York, NY: Farrar, Straus, and Giroux

Local topographic wetness indices predict household malaria risk better than land-use and land-cover in the western Kenya highlands.

Science.gov (United States)

Cohen, Justin M; Ernst, Kacey C; Lindblade, Kim A; Vulule, John M; John, Chandy C; Wilson, Mark L

2010-11-16

Identification of high-risk malaria foci can help enhance surveillance or control activities in regions where they are most needed. Associations between malaria risk and land-use/land-cover are well-recognized, but these environmental characteristics are closely interrelated with the land's topography (e.g., hills, valleys, elevation), which also influences malaria risk strongly. Parsing the individual contributions of land-cover/land-use variables to malaria risk requires examining these associations in the context of their topographic landscape. This study examined whether environmental factors like land-cover, land-use, and urban density improved malaria risk prediction based solely on the topographically-determined context, as measured by the topographic wetness index. The topographic wetness index, an estimate of predicted water accumulation in a defined area, was generated from a digital terrain model of the landscape surrounding households in two neighbouring western Kenyan highland communities. Variables determined to best encompass the variance in this topographic wetness surface were calculated at a household level. Land-cover/land-use information was extracted from a high-resolution satellite image using an object-based classification method. Topographic and land-cover variables were used individually and in combination to predict household-level malaria in the communities through an iterative split-sample model fitting and testing procedure. Models with only topographic variables were compared to those with additional predictive factors related to land-cover/land-use to investigate whether these environmental factors improved prediction of malaria based on the shape of the land alone. Variables related to topographic wetness proved most useful in predicting the households of individuals contracting malaria in this region of rugged terrain. Other variables related to human modification of the environment also demonstrated clear associations with

Local topographic wetness indices predict household malaria risk better than land-use and land-cover in the western Kenya highlands

Directory of Open Access Journals (Sweden)

Vulule John M

2010-11-01

Full Text Available Abstract Background Identification of high-risk malaria foci can help enhance surveillance or control activities in regions where they are most needed. Associations between malaria risk and land-use/land-cover are well-recognized, but these environmental characteristics are closely interrelated with the land's topography (e.g., hills, valleys, elevation, which also influences malaria risk strongly. Parsing the individual contributions of land-cover/land-use variables to malaria risk requires examining these associations in the context of their topographic landscape. This study examined whether environmental factors like land-cover, land-use, and urban density improved malaria risk prediction based solely on the topographically-determined context, as measured by the topographic wetness index. Methods The topographic wetness index, an estimate of predicted water accumulation in a defined area, was generated from a digital terrain model of the landscape surrounding households in two neighbouring western Kenyan highland communities. Variables determined to best encompass the variance in this topographic wetness surface were calculated at a household level. Land-cover/land-use information was extracted from a high-resolution satellite image using an object-based classification method. Topographic and land-cover variables were used individually and in combination to predict household-level malaria in the communities through an iterative split-sample model fitting and testing procedure. Models with only topographic variables were compared to those with additional predictive factors related to land-cover/land-use to investigate whether these environmental factors improved prediction of malaria based on the shape of the land alone. Results Variables related to topographic wetness proved most useful in predicting the households of individuals contracting malaria in this region of rugged terrain. Other variables related to human modification of the

Experiences in monitoring airborne radioactive contamination in JAERI

International Nuclear Information System (INIS)

Ikezawa, Y.; Okamoto, T.; Yabe, A.

1980-01-01

The following results were obtained at the Japan Atomic Energy Research Institute (JAERI) from experience in air monitoring at the hot cells for handling highly radioactive materials, the glove box containing plutonium and the cell for producing 99 Mo. (1) The ratios of activities of airborne dust to those of whole dust were of the order of 10 -2 for the semi-volatile form of 125 Sb, and 10 -3 to 10 -4 for the particulate form of 137 Cs, 144 Ce and 144 Pr, when irradiated fuels were cut in the hot cells. (2) The activity median aerodynamic diameter (AMAD) of airborne particle size distributions varied from O.4 to 15 μm with changing geometric standard deviation (sigmasub(g)) 1.7 to 7, depending on types of metallurgical treatment of fuels and on kinds of work in the cells. (3) A resuspension factor (the ratio of the concentration of airborne contamination to the surface contamination) was found to be 4x10 -8 to approximately 2x10 -7 cm -1 for plutonium oxide deposited on the floor surface. (4) The collection efficiency of the charcoal-loaded filter paper for airborne radioiodine, consisting of 60% inorganic and 40% organic iodide, was over 95% under conditions of relative humidity 40 to approximately 80% and face velocity 50 cm/sec, during the production of 99 Mo. (H.K.)

Topographic Pattern Distribution of Head And Neck Squamous Cell ...

African Journals Online (AJOL)

FINEPRINT

value of 71% of SCC in Turkey. Nevertheless a similar report documented a relatively lower value especially in. Yemen where head and neck SCC constituted only 8% of all head and neck cancers. Reports from Yemen revealed that oral cavity SCC was the most common topographic site of all head and. 3 neck cancers.

Topographic controls on shallow groundwater levels in a steep, prealpine catchment: When are the TWI assumptions valid?

NARCIS (Netherlands)

Rinderer, M.; van Meerveld, H.J.; Seibert, J.

2014-01-01

Topographic indices like the Topographic Wetness Index (TWI) have been used to predict spatial patterns of average groundwater levels and to model the dynamics of the saturated zone during events (e.g., TOPMODEL). However, the assumptions underlying the use of the TWI in hydrological models, of

[Airborne Fungal Aerosol Concentration and Distribution Characteristics in Air- Conditioned Wards].

Science.gov (United States)

Zhang, Hua-ling; Feng, He-hua; Fang, Zi-liang; Wang, Ben-dong; Li, Dan

2015-04-01

The effects of airborne fungus on human health in the hospital environment are related to not only their genera and concentrations, but also their particle sizes and distribution characteristics. Moreover, the mechanisms of aerosols with different particle sizes on human health are different. Fungal samples were obtained in medicine wards of Chongqing using a six-stage sampler. The airborne fungal concentrations, genera and size distributions of all the sampling wards were investigated and identified in detail. Results showed that airborne fungal concentrations were not correlated to the diseases or personnel density, but were related to seasons, temperature, and relative humidity. The size distribution rule had roughly the same for testing wards in winter and summer. The size distributions were not related with diseases and seasons, the percentage of airborne fungal concentrations increased gradually from stage I to stage III, and then decreased dramatically from stage V to stage VI, in general, the size of airborne fungi was a normal distribution. There was no markedly difference for median diameter of airborne fungi which was less 3.19 μm in these wards. There were similar dominant genera in all wards. They were Aspergillus spp, Penicillium spp and Alternaria spp. Therefore, attention should be paid to improve the filtration efficiency of particle size of 1.1-4.7 μm for air conditioning system of wards. It also should be targeted to choose appropriate antibacterial methods and equipment for daily hygiene and air conditioning system operation management.

Real-time monitoring of non-viable airborne particles correlates with airborne colonies and represents an acceptable surrogate for daily assessment of cell-processing cleanroom performance.

Science.gov (United States)

Raval, Jay S; Koch, Eileen; Donnenberg, Albert D

2012-10-01

Airborne particulate monitoring is mandated as a component of good manufacturing practice. We present a procedure developed to monitor and interpret airborne particulates in an International Organization for Standardization (ISO) class 7 cleanroom used for the cell processing of Section 351 and Section 361 products. We collected paired viable and non-viable airborne particle data over a period of 1 year in locations chosen to provide a range of air quality. We used receiver operator characteristic (ROC) analysis to determine empirically the relationship between non-viable and viable airborne particle counts. Viable and non-viable particles were well-correlated (r(2) = 0.78), with outlier observations at the low end of the scale (non-viable particles without detectable airborne colonies). ROC analysis predicted viable counts ≥ 0.5/feet(3) (a limit set by the United States Pharmacopeia) at an action limit of ≥ 32 000 particles (≥ 0.5 µ)/feet(3), with 95.6% sensitivity and 50% specificity. This limit was exceeded 2.6 times during 18 months of retrospective daily cleanroom data (an expected false alarm rate of 1.3 times/year). After implementing this action limit, we were alerted in real time to an air-handling failure undetected by our hospital facilities management. A rational action limit for non-viable particles was determined based on the correlation with airborne colonies. Reaching or exceeding the action limit of 32 000 non-viable particles/feet(3) triggers suspension of cleanroom cell-processing activities, deep cleaning, investigation of air handling, and a deviation management process. Our full procedure for particle monitoring is available as an online supplement.

75 FR 22674 - Airborne Area Navigation Equipment Using Loran-C Inputs

Science.gov (United States)

2010-04-29

... DEPARTMENT OF TRANSPORTATION Federal Aviation Administration Airborne Area Navigation Equipment Using Loran-C Inputs AGENCY: Federal Aviation Administration (FAA), DOT. ACTION: Notice of cancellation... the cancellation of Technical Standard Order (TSO) C-60, Airborne Area Navigation Equipment Using...

75 FR 42819 - Airborne Area Navigation Equipment Using Loran-C Inputs

Science.gov (United States)

2010-07-22

... DEPARTMENT OF TRANSPORTATION Federal Aviation Administration Airborne Area Navigation Equipment Using Loran-C Inputs AGENCY: Federal Aviation Administration (FAA), DOT ACTION: Notice of cancellation... the cancellation of Technical Standard Order (TSO) C-60, Airborne Area Navigation Equipment Using...

Prevalence of food and airborne allergens in allergic patients in Kerman

Directory of Open Access Journals (Sweden)

Hamed Fouladseresht

2014-07-01

Full Text Available Background: Detection of various environmental allergens is the major challenge in allergic diseases and the only treatment is avoiding these allergens. The aim of this study was to determine the prevalence of food and airborne allergens in allergic patients using Skin Prick Test (SPT. Methods: A cross-sectional study was done on clinically confirmed patients of atopic-dermatitis (n=54, allergenic-rhinitis (n=64 and chronic-urticaria (n=39 who referred to asthma and allergy clinic at Afzali-Pour hospital in Kerman during 2008-2010. Skin prick test was done using allergen extracts to determine the patients' sensitivity to food and airborne antigens. Results: Fifty-nine percent of patients responded to at least one allergen. Allergy to airborne and food allergens was 55.9 % and 21.7%, respectively. Chenopodiaceae (22.9% and egg white (10.2% were most prevalent airborne and food allergens. Allergy to cockroach, egg white, egg yolk and tomato was significantly higher in males than in females (P<0.05. Conclusion: The results indicated that allergy to food and airborne allergens is different depending on the nutrition and environmental conditions.

78 FR 44625 - Proposed Information Collection (Open Burn Pit Registry Airborne Hazard Self-Assessment...

Science.gov (United States)

2013-07-24

... DEPARTMENT OF VETERANS AFFAIRS Proposed Information Collection (Open Burn Pit Registry Airborne... to ``OMB Control No. 2900--NEW, Open Burn Pit Registry Airborne Hazard Self-Assessment Questionnaire... health effects of service members' exposure to toxic airborne chemicals and fumes caused by open burn...

Adobe Illustrator drawing showing geophysical and topographical survey data and interpretations

OpenAIRE

Wallace, Lacey; Ferraby, Rose

2016-01-01

Adobe Illustrator drawing at 1:2000 that shows the rasters and interpretations of the geophysics, the topographical contours, and the survey areas, with British National Grid coordinates and Ordnance Survey Master Map data included.

Airborne Radar Search for Diesel Submarines

National Research Council Canada - National Science Library

Pilnick, Steven E; Landa, Jose

2005-01-01

.... In this research, a detection rate model is developed to analyze the effectiveness of airborne radar search for a diesel submarine assumed to be intermittently operating with periscopes or masts...

Biophysical influence of airborne carbon nanomaterials on natural pulmonary surfactant.

Science.gov (United States)

Valle, Russell P; Wu, Tony; Zuo, Yi Y

2015-05-26

Inhalation of nanoparticles (NP), including lightweight airborne carbonaceous nanomaterials (CNM), poses a direct and systemic health threat to those who handle them. Inhaled NP penetrate deep pulmonary structures in which they first interact with the pulmonary surfactant (PS) lining at the alveolar air-water interface. In spite of many research efforts, there is a gap of knowledge between in vitro biophysical study and in vivo inhalation toxicology since all existing biophysical models handle NP-PS interactions in the liquid phase. This technical limitation, inherent in current in vitro methodologies, makes it impossible to simulate how airborne NP deposit at the PS film and interact with it. Existing in vitro NP-PS studies using liquid-suspended particles have been shown to artificially inflate the no-observed adverse effect level of NP exposure when compared to in vivo inhalation studies and international occupational exposure limits (OELs). Here, we developed an in vitro methodology called the constrained drop surfactometer (CDS) to quantitatively study PS inhibition by airborne CNM. We show that airborne multiwalled carbon nanotubes and graphene nanoplatelets induce a concentration-dependent PS inhibition under physiologically relevant conditions. The CNM aerosol concentrations controlled in the CDS are comparable to those defined in international OELs. Development of the CDS has the potential to advance our understanding of how submicron airborne nanomaterials affect the PS lining of the lung.

Airborne systems for emergency radiological monitoring

International Nuclear Information System (INIS)

Jupiter, C.; Boyns, P.

1976-01-01

A variety of aerial radiological monitoring systems are available to respond to a radiological accident or incident affecting large areas. These are operated by EG and G, Inc. for ERDA's Division of Operational Safety. A survey system can be airborne within approximately two hours after notification. Both airborne and terrestrial radioactivity can be measured and mapped. Special analysis procedures allow discrimination between radioactivity from most man-made radioelements and naturally occurring radioelements. A position accuracy of +-54 feet can be maintained over a large area survey. Detection sensitivity for gamma sources employing NaI detector arrays on board an airplane flying at 500 feet altitude is better than 2 μR/hr for surface planar contaminants and approximately 10 mCi for a point gamma source

Measuring canopy structure with an airborne laser altimeter

International Nuclear Information System (INIS)

Ritchie, J.C.; Evans, D.L.; Jacobs, D.; Everitt, J.H.; Weltz, M.A.

1993-01-01

Quantification of vegetation patterns and properties is needed to determine their role on the landscape and to develop management plans to conserve our natural resources. Quantifying vegetation patterns from the ground, or by using aerial photography or satellite imagery is difficult, time consuming, and often expensive. Digital data from an airborne laser altimeter offer an alternative method to quantify selected vegetation properties and patterns of forest and range vegetation. Airborne laser data found canopy heights varied from 2 to 6 m within even-aged pine forests. Maximum canopy heights measured with the laser altimeter were significantly correlated to measurements made with ground-based methods. Canopy shape could be used to distinguish deciduous and evergreen trees. In rangeland areas, vegetation heights, spatial patterns, and canopy cover measured with the laser altimeter were significantly related with field measurements. These studies demonstrate the potential of airborne laser data to measure canopy structure and properties for large areas quickly and quantitatively

EUFAR the unique portal for airborne research in Europe

Science.gov (United States)

Gérard, Elisabeth; Brown, Philip

2016-04-01

Created in 2000 and supported by the EU Framework Programmes since then, EUFAR was born out of the necessity to create a central network and access point for the airborne research community in Europe. With the aim to support researchers by granting them access to research infrastructures, not accessible in their home countries, EUFAR also provides technical support and training in the field of airborne research for the environmental and geo-sciences. Today, EUFAR2 (2014-2018) coordinates and facilitates transnational access to 18 instrumented aircraft and 3 remote-sensing instruments through the 13 operators who are part of EUFAR's current 24-partner European consortium. In addition, the current project supports networking and research activities focused on providing an enabling environment for and promoting airborne research. The EUFAR2 activities cover three objectives, supported by the internet website www.eufar.net: (I - Institutional) improvement of the access to the research infrastructures and development of the future fleet according to the strategic advisory committee (SAC) recommendations; (ii - Innovation) improvement of the scientific knowledge and promotion of innovating instruments, processes and services for the emergence of new industrial technologies, with an identification of industrial needs by the SAC; (iii - Service) optimisation and harmonisation of the use of the research infrastructures through the development of the community of young researches in airborne science, of the standards and protocols and of the airborne central database. With the launch of a brand new website (www.eufar.net) in mid-November 2015, EUFAR aims to improve user experience on the website, which serves as a source of information and a hub where users are able to collaborate, learn, share expertise and best practices, and apply for transnational access, and education and training funded opportunities within the network. With its newly designed eye-catching interface

Exposure level and distribution characteristics of airborne bacteria and fungi in Seoul metropolitan subway stations.

Science.gov (United States)

Kim, Ki Youn; Kim, Yoon Shin; Kim, Daekeun; Kim, Hyeon Tae

2011-01-01

The exposure level and distribution characteristics of airborne bacteria and fungi were assessed in the workers' activity areas (station office, bedroom, ticket office and driver's seat) and passengers' activity areas (station precinct, inside the passenger carriage, and platform) of the Seoul metropolitan subway. Among investigated areas, the levels of airborne bacteria and fungi in the workers' bedroom and station precincts were relatively high. No significant difference was found in the concentration of airborne bacteria and fungi between the underground and above ground activity areas of the subway. The genera identified in all subway activity areas with a 5% or greater detection rate were Staphylococcus, Micrococcus, Bacillus and Corynebacterium for airborne bacteria and Penicillium, Cladosporium, Chrysosporium, Aspergillus for airborne fungi. Staphylococcus and Micrococcus comprised over 50% of the total airborne bacteria and Penicillium and Cladosporium comprised over 60% of the total airborne fungi, thus these four genera are the predominant genera in the subway station.

SOFIA's Airborne Astronomy Ambassadors: An External Evaluation of Cycle 1

Science.gov (United States)

Phillips, Michelle

2015-01-01

The Stratospheric Observatory for Infrared Astronomy (SOFIA) represents a partnership between NASA and the German Aerospace Center (DLR). The observatory itself is a Boeing 747 SP that has been modified to serve as the world's largest airborne research observatory. The SOFIA Airborne Astronomy Ambassadors (AAA) program is a component of SOFIA's…

Fabrication of disposable topographic silicon oxide from sawtoothed patterns: control of arrays of gold nanoparticles.

Science.gov (United States)

Cho, Heesook; Yoo, Hana; Park, Soojin

2010-05-18

Disposable topographic silicon oxide patterns were fabricated from polymeric replicas of sawtoothed glass surfaces, spin-coating of poly(dimethylsiloxane) (PDMS) thin films, and thermal annealing at certain temperature and followed by oxygen plasma treatment of the thin PDMS layer. A simple imprinting process was used to fabricate the replicated PDMS and PS patterns from sawtoothed glass surfaces. Next, thin layers of PDMS films having different thicknesses were spin-coated onto the sawtoothed PS surfaces and annealed at 60 degrees C to be drawn the PDMS into the valley of the sawtoothed PS surfaces, followed by oxygen plasma treatment to fabricate topographic silicon oxide patterns. By control of the thickness of PDMS layers, silicon oxide patterns having various line widths were fabricated. The silicon oxide topographic patterns were used to direct the self-assembly of polystyrene-block-poly(2-vinylpyridine) (PS-b-P2VP) block copolymer thin films via solvent annealing process. A highly ordered PS-b-P2VP micellar structure was used to let gold precursor complex with P2VP chains, and followed by oxygen plasma treatment. When the PS-b-P2VP thin films containing gold salts were exposed to oxygen plasma environments, gold salts were reduced to pure gold nanoparticles without changing high degree of lateral order, while polymers were completely degraded. As the width of trough and crest in topographic patterns increases, the number of gold arrays and size of gold nanoparticles are tuned. In the final step, the silicon oxide topographic patterns were selectively removed by wet etching process without changing the arrays of gold nanoparticles.

New implementation of a shear-force microscope suitable to study topographical features over wide areas

International Nuclear Information System (INIS)

Ustione, A.; Cricenti, A.; Piacentini, M.; Felici, A. C.

2006-01-01

A new implementation of a shear-force microscope is described that uses a shear-force detection system to perform topographical imaging of large areas (∼1x1 mm 2 ). This implementation finds very interesting application in the study of archeological or artistic samples. Three dc motors are used to move a sample during a scan, allowing the probe tip to follow the surface and to face height differences of several tens of micrometers. This large-area topographical imaging mode exploits new subroutines that were added to the existing homemade software; these subroutines were created in Microsoft VISUAL BASIC 6.0 programming language. With this new feature our shear-force microscope can be used to study topographical details over large areas of archaeological samples in a nondestructive way. We show results detecting worn reliefs over a coin

Topographic filtering simulation model for sediment source apportionment

Science.gov (United States)

Cho, Se Jong; Wilcock, Peter; Hobbs, Benjamin

2018-05-01

We propose a Topographic Filtering simulation model (Topofilter) that can be used to identify those locations that are likely to contribute most of the sediment load delivered from a watershed. The reduced complexity model links spatially distributed estimates of annual soil erosion, high-resolution topography, and observed sediment loading to determine the distribution of sediment delivery ratio across a watershed. The model uses two simple two-parameter topographic transfer functions based on the distance and change in elevation from upland sources to the nearest stream channel and then down the stream network. The approach does not attempt to find a single best-calibrated solution of sediment delivery, but uses a model conditioning approach to develop a large number of possible solutions. For each model run, locations that contribute to 90% of the sediment loading are identified and those locations that appear in this set in most of the 10,000 model runs are identified as the sources that are most likely to contribute to most of the sediment delivered to the watershed outlet. Because the underlying model is quite simple and strongly anchored by reliable information on soil erosion, topography, and sediment load, we believe that the ensemble of simulation outputs provides a useful basis for identifying the dominant sediment sources in the watershed.

Airborne campaigns for CryoSat pre-launch calibration and validation

DEFF Research Database (Denmark)

Hvidegaard, Sine Munk; Forsberg, René; Skourup, Henriette

2010-01-01

From 2003 to 2008 DTU Space together with ESA and several international partners carried out airborne and ground field campaigns in preparation for CryoSat validation; called CryoVEx: CryoSat Validation Experiments covering the main ice caps in Greenland, Canada and Svalbard and sea ice in the Ar......From 2003 to 2008 DTU Space together with ESA and several international partners carried out airborne and ground field campaigns in preparation for CryoSat validation; called CryoVEx: CryoSat Validation Experiments covering the main ice caps in Greenland, Canada and Svalbard and sea ice...... in the Arctic Ocean. The main goal of the airborne surveys was to acquire coincident scanning laser and CryoSat type radar elevation measurements of the surface; either sea ice or land ice. Selected lines have been surveyed along with detailed mapping of validation sites coordinated with insitu field work...... and helicopter electromagnetic surveying. This paper summarises the pre-launch campaigns and presents some of the result from the coincident measurement from airborne and ground observations....

Relationships between Arctic shrub dynamics and topographically derived hydrologic characteristics

International Nuclear Information System (INIS)

Naito, Adam T; Cairns, David M

2011-01-01

Shrub expansion is a global phenomenon that is gaining increased attention in the Arctic. Recent work employing the use of oblique aerial photographs suggested a consistent pattern of positive change in shrub cover across the North Slope of Alaska. The greatest amounts of change occurred in valley slopes and floodplains. We studied the association between shrub cover change and topographically derived hydrologic characteristics in five areas in northern Alaska between the 1970s and 2000s. Change in total shrub cover ranged from − 0.65% to 46.56%. Change in floodplain shrub cover ranged from 3.38% to 76.22%. Shrubs are preferentially expanding into areas of higher topographic wetness index (TWI) values where the potential for moisture accumulation or drainage is greater. In addition, we found that floodplain shrub development was strongly associated with high TWI values and a decreasing average distance between shrubs and the river bank. This suggests an interacting influence of substrate removal and stabilization as a consequence of increased vegetation cover.

Airborne gamma-ray spectrometer and magnetometer survey: Lund quadrangle, Ely quadrangle, Nevada. Volume I. Final report

International Nuclear Information System (INIS)

1980-01-01

An airborne combined radiometric and magnetic survey was performed for the Department of Energy (DOE) over the area covered by the Ely and Lund 1:250,000 National Topographic Map Series (NTMS quadrangle maps). The survey was part of DOE's National Uranium Resource Evaluation (NURE) Aerial Radiometric Reconnaissance program. Data were collected by a helicopter equipped with a gamma-ray spectrometer having a large crystal volume, and a high sensitivity proton precession magnetometer. The radiometric system was calibrated at the Walker Field Calibration pads and the Lake Mead Dynamic Test range. Data quality was ensured during the survey by daily test flights and equipment checks. Radiometric data were corrected for live time, aircraft and equipment background, cosmic background, atmospheric radon, Compton scatter, and altitude dependence. The corrected data were statistically evaluated, plotted, and contoured to produce anomaly maps based on the radiometric response of individual geological units. The maps were interpreted and an anomaly interpretation map produced. Volume I contains a description of the systems used in the survey, a discussion of the calibration of the systems, the data processing procedures, the data display format, the interpretation rationale, and interpretation methodology. Volume II contains the data displays for a quadrangle and the interpretation results

Urban Airborne Lead: X-Ray Absorption Spectroscopy Establishes Soil as Dominant Source

OpenAIRE

Pingitore, Nicholas E.; Clague, Juan W.; Amaya, Maria A.; Maciejewska, Beata; Reynoso, Jes?s J.

2009-01-01

BACKGROUND: Despite the dramatic decrease in airborne lead over the past three decades, there are calls for regulatory limits on this potent pediatric neurotoxin lower even than the new (2008) US Environmental Protection Agency standard. To achieve further decreases in airborne lead, what sources would need to be decreased and what costs would ensue? Our aim was to identify and, if possible, quantify the major species (compounds) of lead in recent ambient airborne particulate matter collected...

A fast approach to generate large-scale topographic maps based on new Chinese vehicle-borne Lidar system

International Nuclear Information System (INIS)

Youmei, Han; Bogang, Yang

2014-01-01

Large -scale topographic maps are important basic information for city and regional planning and management. Traditional large- scale mapping methods are mostly based on artificial mapping and photogrammetry. The traditional mapping method is inefficient and limited by the environments. While the photogrammetry methods(such as low-altitude aerial mapping) is an economical and effective way to map wide and regulate range of large scale topographic map but doesn't work well in the small area due to the high cost of manpower and resources. Recent years, the vehicle-borne LIDAR technology has a rapid development, and its application in surveying and mapping is becoming a new topic. The main objective of this investigation is to explore the potential of vehicle-borne LIDAR technology to be used to fast mapping large scale topographic maps based on new Chinese vehicle-borne LIDAR system. It studied how to use the new Chinese vehicle-borne LIDAR system measurement technology to map large scale topographic maps. After the field data capture, it can be mapped in the office based on the LIDAR data (point cloud) by software which programmed by ourselves. In addition, the detailed process and accuracy analysis were proposed by an actual case. The result show that this new technology provides a new fast method to generate large scale topographic maps, which is high efficient and accuracy compared to traditional methods

Computer-controlled sampling system for airborne particulates

International Nuclear Information System (INIS)

Hall, C.F.; Anspaugh, L.R.; Koval, J.S.; Phelps, P.L.; Steinhaus, R.J.

1975-01-01

A self-contained, mobile, computer-controlled air-sampling system has been designed and fabricated that also collects and records the data from eight meteorological sensors. The air-samplers are activated automatically when the collected meteorological data meet the criteria specified at the beginning of the data-collection run. The filters from the samplers are intended to collect airborne 239 Pu for later radionuclide analysis and correlation with the meteorological data for the study of resuspended airborne radioactivity and for the development of a predictive model. This paper describes the system hardware, discusses the system and software concepts, and outlines the operational procedures for the system

Attenuation of airborne debris from LMFBR accidents

International Nuclear Information System (INIS)

Morewitz, H.A.; Johnson, R.P.; Nelson, C.T.; Vaughan, E.U.; Guderjahn, C.A.; Hilliard, R.K.; McCormack, J.D.; Postma, A.K.

1978-01-01

Experimental and theoretical studies have been performed to characterize the behavior of airborne particulates (aerosols) expected to be produced by hypothetical core disassembly accidents (HCDA's) in liquid metal fast breeder reactors (LMFBR's). These aerosol studies include work on aerosol transport in a 20-m high, 850-m 3 closed vessel at moderate concentrations; aerosol transport in a small vessel under conditions of high concentration (approximately 1,000 g/m 3 ), high turbulence, and high temperature (approximately 2000 0 C); and aerosol transport through various leak paths. These studies have shown that tittle, if any, airborne debris from LMFBR HCDA's would reach the atmosphere exterior to an intact reactor containment building. (author)

Correction of systematic behaviour in topographical surface analysis

DEFF Research Database (Denmark)

Quagliotti, Danilo; Baruffi, Federico; Tosello, Guido

2016-01-01

Four specimens in the sub-micrometre range and with different polishing were topographically investigated in fiveareas over their respective surfaces. Uncertainties were evaluated with and without correction for systematicbehaviour and successively analysed by a design of experiment (DOE). Result...... showed that the correction forsystematic behaviour allowed for a lower value of the estimated uncertainty when the correction was adequate tocompletely recognise the systematic effects. If not, the correction can produce an overestimation of the uncertainty....

Airborne Mission Concept for Coastal Ocean Color and Ecosystems Research

Science.gov (United States)

Guild, Liane S.; Hooker, Stanford B.; Morrow, John H.; Kudela, Raphael M.; Palacios, Sherry L.; Torres Perez, Juan L.; Hayashi, Kendra; Dunagan, Stephen E.

2016-01-01

NASA airborne missions in 2011 and 2013 over Monterey Bay, CA, demonstrated novel above- and in-water calibration and validation measurements supporting a combined airborne sensor approach (imaging spectrometer, microradiometers, and a sun photometer). The resultant airborne data characterize contemporaneous coastal atmospheric and aquatic properties plus sea-truth observations from state-of-the-art instrument systems spanning a next-generation spectral domain (320-875 nm). This airborne instrument suite for calibration, validation, and research flew at the lowest safe altitude (ca. 100 ft or 30 m) as well as higher altitudes (e.g., 6,000 ft or 1,800 m) above the sea surface covering a larger area in a single synoptic sortie than ship-based measurements at a few stations during the same sampling period. Data collection of coincident atmospheric and aquatic properties near the sea surface and at altitude allows the input of relevant variables into atmospheric correction schemes to improve the output of corrected imaging spectrometer data. Specific channels support legacy and next-generation satellite capabilities, and flights are planned to within 30 min of satellite overpass. This concept supports calibration and validation activities of ocean color phenomena (e.g., river plumes, algal blooms) and studies of water quality and coastal ecosystems. The 2011 COAST mission flew at 100 and 6,000 ft on a Twin Otter platform with flight plans accommodating the competing requirements of the sensor suite, which included the Coastal-Airborne In-situ Radiometers (C-AIR) for the first time. C-AIR (Biospherical Instruments Inc.) also flew in the 2013 OCEANIA mission at 100 and 1,000 ft on the Twin Otter below the California airborne simulation of the proposed NASA HyspIRI satellite system comprised of an imaging spectrometer and thermal infrared multispectral imager on the ER-2 at 65,000 ft (20,000 m). For both missions, the Compact-Optical Profiling System (Biospherical

Experience with airborne detection of radioactive pollution (ENMOS, IRIS)

International Nuclear Information System (INIS)

PAVLIK, B.; ENGELSMANN, J.

2003-01-01

Technological advancements of our society create with the increased level of comfort, increased risk of either unintentional or intentional radioactive pollution. New instrumentation and processing techniques can rapidly produce visual images of areas exposed to radiation. Protecting the health of the population in case of a nuclear accident is an essential social priority. Monitoring of existing levels of natural and manmade radioactive contamination, in and around nuclear installations and nuclear materials handling facilities is a valuable reference in case of a nuclear accident. Fast deployment of airborne radiation monitoring systems in the case of nuclear accidents is essential. The portability of the new range of instrumentation with accurate navigation, data acquisition and real time processing can provide fast and low cost estimates of potential problems. Many examples of real situations assessed on the basis of data gained by the airborne measurements demonstrate, that the use of airborne data is reliable, fast and relatively inexpensive. Short period of time required for data acquisition assures data consistency. Practically unrestricted access provides good and homogeneous data. Today advanced measuring and processing techniques are result of many years of hard and slow progress mostly in airborne geophysics, together with advancements in mathematics, physics, data processing and electronics. (authors)

Experience with airborne detection of radioactive pollution (ENMOS, IRIS)

Energy Technology Data Exchange (ETDEWEB)

PAVLIK, B [Pico Envirotec Inc. Division of Eikon Envirotec Technologies Inc., Concord, Ontario (Canada); ENGELSMANN, J [AURA s.r.o., Brno (Czech Republic)

2003-07-01

Technological advancements of our society create with the increased level of comfort, increased risk of either unintentional or intentional radioactive pollution. New instrumentation and processing techniques can rapidly produce visual images of areas exposed to radiation. Protecting the health of the population in case of a nuclear accident is an essential social priority. Monitoring of existing levels of natural and manmade radioactive contamination, in and around nuclear installations and nuclear materials handling facilities is a valuable reference in case of a nuclear accident. Fast deployment of airborne radiation monitoring systems in the case of nuclear accidents is essential. The portability of the new range of instrumentation with accurate navigation, data acquisition and real time processing can provide fast and low cost estimates of potential problems. Many examples of real situations assessed on the basis of data gained by the airborne measurements demonstrate, that the use of airborne data is reliable, fast and relatively inexpensive. Short period of time required for data acquisition assures data consistency. Practically unrestricted access provides good and homogeneous data. Today advanced measuring and processing techniques are result of many years of hard and slow progress mostly in airborne geophysics, together with advancements in mathematics, physics, data processing and electronics. (authors)

Airborne monitoring system

International Nuclear Information System (INIS)

Kadmon, Y.; Gabovitch, A.; Tirosh, D.; Ellenbogen, M.; Mazor, T.; Barak, D.

1997-01-01

A complete system for tracking, mapping, and performing a composition analysis of a radioactive plume and contaminated area was developed at the NRCN. The system includes two major units : An airborne unit for monitoring and a ground station for analyzing. The airborne unit is mounted on a helicopter and includes file following. Four radiation sensor, two 2'' x 2'' Nal (Tl) sensors horizontally separated by lead shield for mapping and spectroscopy, and two Geiger Mueller (GM) tubes as part of the safety system. A multichannel analyzer card is used for spectroscopy. A navigation system, based on GPS and a barometric altitude meter, is used to locate the plume or ground data. The telemetry system, consisting of a transceiver and a modem, transfers all the data in real time to the ground station. An industrial PC (Field Works) runs a dedicated C++ Windows application to manage the acquired data. An independent microprocessor based backup system includes a recorder, display, and key pad. The ground station is based on an industrial PC, a telemetry system, a color printer and a modem to communicate with automatic meteorology stations in the relevant area. A special software controls the ground station. Measurement results are analyzed in the ground station to estimate plume parameters including motion, location, size, velocity, and perform risk assessment. (authors)

Airborne lead and particulate levels in Semarang, Indonesia and potential health impacts.

Science.gov (United States)

Browne, D R; Husni, A; Risk, M J

1999-03-09

Spatial and temporal variation in airborne lead and total suspended particulates was examined in the city of Semarang, Indonesia, and surrounding area. Both airborne lead and TSP varied significantly with the type of urban development. Mean urban airborne lead levels were 0.35 microgram/m3 in the highway zone, 0.95 microgram/m3 in the residential zone, and 0.99 microgram/m3 in the commercial zone. Airborne lead levels in the industrial zone were significantly higher than all other areas, with a mean of 8.41 micrograms/m3. Airborne lead concentrations of this magnitude have not been reported in Indonesia previously. Mean TSP levels ranged from 115.5 micrograms/m3 to 165.8 micrograms/m3 in urban areas. Increased levels of TSP were associated with areas adjacent to major transportation routes. On a seasonal basis, TSP levels were significantly lower during the rainy season, while mean airborne lead levels did not show a significant seasonal trend. Observed ambient pollution levels were translated into potential heath impacts based on previously established relationships. Increased levels of TSP pollution near major roads was estimated to result in a 1.6% increase in mortality for all causes of death and a 7.9% increase in mortality due to respiratory disease. Estimated child blood lead levels indicated possible lead toxicity among Semarang children.

Structural Modeling and Analysis on Dynamic Characteristics of Antenna Pedestal in Airborne SAR

Directory of Open Access Journals (Sweden)

He Li-ping

2012-06-01

Full Text Available Finite element modeling and structural dynamic characteristics of antenna pedestal in airborne SAR were studied in this paper. The Finite element model of antenna pedestal in airborne SAR was set up on the basis of structural dynamic theory, then, the key technologies of dynamic simulation were pointed out, and the modal analysis and transient analysis were carried out. Simulation results show that the dynamic characteristics of antenna pedestal in airborne SAR can meet the requirements of servo bandwidth and structural strength. The fast finite element modeling and simulation method proposed in this paper are of great significance to the weight reducing design of antenna pedestal in airborne SAR.

47 CFR 22.925 - Prohibition on airborne operation of cellular telephones.

Science.gov (United States)

2010-10-01

... 47 Telecommunication 2 2010-10-01 2010-10-01 false Prohibition on airborne operation of cellular... CARRIER SERVICES PUBLIC MOBILE SERVICES Cellular Radiotelephone Service § 22.925 Prohibition on airborne operation of cellular telephones. Cellular telephones installed in or carried aboard airplanes, balloons or...

Effect of ADS-B Characteristics on Airborne Conflict Detection and Resolution

NARCIS (Netherlands)

Langejan, T.P.; Sunil, E.; Ellerbroek, J.; Hoekstra, J.M.

2016-01-01

Most Free-Flight concepts rely on self-separation by means of airborne Conflict Detection and Resolution (CD&R) algorithms. A key enabling technology for airborne CD&R is the Automatic Dependent Surveillance-Broadcast (ADS-B) system, which is used for direct state information exchange

Airborne soil particulates as vehicles for Salmonella contamination of tomatoes.

Science.gov (United States)

Kumar, Govindaraj Dev; Williams, Robert C; Al Qublan, Hamzeh M; Sriranganathan, Nammalwar; Boyer, Renee R; Eifert, Joseph D

2017-02-21

The presence of dust is ubiquitous in the produce growing environment and its deposition on edible crops could occur. The potential of wind-distributed soil particulate to serve as a vehicle for S. Newport transfer to tomato blossoms and consequently, to fruits, was explored. Blossoms were challenged with previously autoclaved soil containing S. Newport (9.39log CFU/g) by brushing and airborne transfer. One hundred percent of blossoms brushed with S. Newport-contaminated soil tested positive for presence of the pathogen one week after contact (PCompressed air was used to simulate wind currents and direct soil particulates towards blossoms. Airborne soil particulates resulted in contamination of 29% of the blossoms with S. Newport one week after contact. Biophotonic imaging of blossoms post-contact with bioluminescent S. Newport-contaminated airborne soil particulates revealed transfer of the pathogen on petal, stamen and pedicel structures. Both fruits and calyxes that developed from blossoms contaminated with airborne soil particulates were positive for presence of S. Newport in both fruit (66.6%) and calyx (77.7%). Presence of S. Newport in surface-sterilized fruit and calyx tissue tested indicated internalization of the pathogen. These results show that airborne soil particulates could serve as a vehicle for Salmonella. Hence, Salmonella contaminated dust and soil particulate dispersion could contribute to pathogen contamination of fruit, indicating an omnipresent yet relatively unexplored contamination route. Copyright © 2016 Elsevier B.V. All rights reserved.

Airborne Particulate Matter Induces Nonallergic Eosinophilic Sinonasal Inflammation in Mice.

Science.gov (United States)

Ramanathan, Murugappan; London, Nyall R; Tharakan, Anuj; Surya, Nitya; Sussan, Thomas E; Rao, Xiaoquan; Lin, Sandra Y; Toskala, Elina; Rajagopalan, Sanjay; Biswal, Shyam

2017-07-01

Exposure to airborne particulate matter (PM) has been linked to aggravation of respiratory symptoms, increased risk of cardiovascular disease, and all-cause mortality. Although the health effects of PM on the lower pulmonary airway have been extensively studied, little is known regarding the impact of chronic PM exposure on the upper sinonasal airway. We sought to test the impact of chronic airborne PM exposure on the upper respiratory system in vivo. Mice were subjected, by inhalation, to concentrated fine (2.5 μm) PM 6 h/d, 5 d/wk, for 16 weeks. Mean airborne fine PM concentration was 60.92 μm/m 3 , a concentration of fine PM lower than that reported in some major global cities. Mice were then killed and analyzed for evidence of inflammation and barrier breakdown compared with control mice. Evidence of the destructive effects of chronic airborne PM on sinonasal health in vivo, including proinflammatory cytokine release, and macrophage and neutrophil inflammatory cell accumulation was observed. A significant increase in epithelial barrier dysfunction was observed, as assessed by serum albumin accumulation in nasal airway lavage fluid, as well as decreased expression of adhesion molecules, including claudin-1 and epithelial cadherin. A significant increase in eosinophilic inflammation, including increased IL-13, eotaxin-1, and eosinophil accumulation, was also observed. Collectively, although largely observational, these studies demonstrate the destructive effects of chronic airborne PM exposure on the sinonasal airway barrier disruption and nonallergic eosinophilic inflammation in mice.

Modeling Change of Topographic Spatial Structures with DEM Resolution Using Semi-Variogram Analysis and Filter Bank

Directory of Open Access Journals (Sweden)

Chunmei Wang

2016-06-01

Full Text Available In this paper, the way topographic spatial information changes with resolution was investigated using semi-variograms and an Independent Structures Model (ISM to identify the mechanisms involved in changes of topographic parameters as resolution becomes coarser or finer. A typical Loess Hilly area in the Loess Plateau of China was taken as the study area. DEMs with resolutions of 2.5 m and 25 m were derived from topographic maps with map scales of 1:10,000 using ANUDEM software. The ISM, in which the semi-variogram was modeled as the sum of component semi-variograms, was used to model the measured semi-variogram of the elevation surface. Components were modeled using an analytic ISM model and corresponding landscape components identified using Kriging and filter bank analyses. The change in the spatial components as resolution became coarser was investigated by modeling upscaling as a low pass linear filter and applying a general result to obtain an analytic model for the scaling process in terms of semi-variance. This investigation demonstrated how topographic structures could be effectively characterised over varying scales using the ISM model for the semi-variogram. The loss of information in the short range components with resolution is a major driver for the observed change in derived topographic parameters such as slope. This paper has helped to quantify how information is distributed among scale components and how it is lost in natural terrain surfaces as resolution becomes coarser. It is a basis for further applications in the field of geomorphometry.

Occurrence of airborne vancomycin- and gentamicin-resistant bacteria in various hospital wards in Isfahan, Iran.

Science.gov (United States)

Mirhoseini, Seyed Hamed; Nikaeen, Mahnaz; Khanahmad, Hossein; Hassanzadeh, Akbar

2016-01-01

Airborne transmission of pathogenic resistant bacteria is well recognized as an important route for the acquisition of a wide range of nosocomial infections in hospitals. The aim of this study was to determine the prevalence of airborne vancomycin and gentamicin (VM and GM) resistant bacteria in different wards of four educational hospitals. A total of 64 air samples were collected from operating theater (OT), Intensive Care Unit (ICU), surgery ward, and internal medicine ward of four educational hospitals in Isfahan, Iran. Airborne culturable bacteria were collected using all glass impingers. Samples were analyzed for the detection of VM- and GM-resistant bacteria. The average level of bacteria ranged from 99 to 1079 CFU/m(3). The highest level of airborne bacteria was observed in hospital 4 (628 CFU/m(3)) and the highest average concentration of GM- and VM-resistant airborne bacteria were found in hospital 3 (22 CFU/m(3)). The mean concentration of airborne bacteria was the lowest in OT wards and GM- and VM-resistant airborne bacteria were not detected in this ward of hospitals. The highest prevalence of antibiotic-resistant airborne bacteria was observed in ICU ward. There was a statistically significant difference for the prevalence of VM-resistant bacteria between hospital wards (P = 0.012). Our finding showed that the relatively high prevalence of VM- and GM-resistant airborne bacteria in ICUs could be a great concern from the point of view of patients' health. These results confirm the necessity of application of effective control measures which significantly decrease the exposure of high-risk patients to potentially airborne nosocomial infections.

Separating topographical and chemical analysis of nanostructure of polymer composite in low voltage SEM

International Nuclear Information System (INIS)

Wan, Q; Plenderleith, R A; Claeyssens, F; Rodenburg, C; Dapor, M; Rimmer, S

2015-01-01

The possibility of separating the topographical and chemical information in a polymer nano-composite using low-voltage SEM imaging is demonstrated, when images are acquired with a Concentric Backscattered (CBS) detector. This separation of chemical and topographical information is based on the different angular distribution of electron scattering which were calculated using a Monte Carlo simulation. The simulation based on angular restricted detection was applied to a semi-branched PNIPAM/PEGDA interpenetration network for which a linear relationship of topography SEM contrast and feature height data was observed. (paper)

Issues relating to airborne applications of HTS SQUIDs

International Nuclear Information System (INIS)

Foley, C P; Leslie, K E; Binks, R A; Lam, S H K; Du, J; Tilbrook, D L; Mitchell, E E; Macfarlane, J C; Lee, J B; Turner, R; Downey, M; Maddever, A

2002-01-01

Airborne application of HTS SQUIDs is the most difficult environment for their successful deployment. In order to operate with the sensitivity required for a particular application, there are many issues to be addressed such as the need for very wide dynamic range electronics, motion noise elimination, immunity to large changing magnetic fields and cultural noise sources. This paper reviews what is necessary to achieve an airborne system giving examples in geophysical mineral exploration. It will consider issues relating to device design and fabrication, electronics, dewar design, suspension system requirements and noise elimination methods

Issues relating to airborne applications of HTS SQUIDs

CERN Document Server

Foley, C P; Binks, R A; Lam, S H K; Du, J; Tilbrook, D L; Mitchell, E E; MacFarlane, J C; Lee, J B; Turner, R; Downey, M; Maddever, A

2002-01-01

Airborne application of HTS SQUIDs is the most difficult environment for their successful deployment. In order to operate with the sensitivity required for a particular application, there are many issues to be addressed such as the need for very wide dynamic range electronics, motion noise elimination, immunity to large changing magnetic fields and cultural noise sources. This paper reviews what is necessary to achieve an airborne system giving examples in geophysical mineral exploration. It will consider issues relating to device design and fabrication, electronics, dewar design, suspension system requirements and noise elimination methods.

Meteorological factors associated with abundance of airborne fungal spores over natural vegetation

Science.gov (United States)

Crandall, Sharifa G.; Gilbert, Gregory S.

2017-08-01

The abundance of airborne fungal spores in agricultural and urban settings increases with greater air temperature, relative humidity, or precipitation. The same meteorological factors that affect temporal patterns in spore abundance in managed environments also vary spatially across natural habitats in association with differences in vegetation structure. Here we investigated how temporal and spatial variation in aerial spore abundance is affected by abiotic (weather) and biotic (vegetation) factors as a foundation for predicting how fungi may respond to changes in weather and land-use patterns. We measured the phenology of airborne fungal spores across a mosaic of naturally occurring vegetation types at different time scales to describe (1) how spore abundance changes over time, (2) which local meteorological variables are good predictors for airborne spore density, and (3) whether spore abundance differs across vegetation types. Using an air volumetric vacuum sampler, we collected spore samples at 3-h intervals over a 120-h period in a mixed-evergreen forest and coastal prairie to measure diurnal, nocturnal, and total airborne spore abundance across vegetation types. Spore samples were also collected at weekly and monthly intervals in mixed-evergreen forest, redwood forest, and maritime chaparral vegetation types from 12 field sites across two years. We found greater airborne spore densities during the wetter winter months compared to the drier summer months. Mean total spore abundance in the mixed-evergreen forest was twice than in the coastal prairie, but there were no significant differences in total airborne spore abundance among mixed-evergreen forest, redwood forest, and maritime chaparral vegetation types. Weekly and monthly peaks in airborne spore abundance corresponded with rain events and peaks in soil moisture. Overall, temporal patterns in meteorological factors were much more important in determining airborne fungal spore abundance than the

A suite of global, cross-scale topographic variables for environmental and biodiversity modeling

Science.gov (United States)

Amatulli, Giuseppe; Domisch, Sami; Tuanmu, Mao-Ning; Parmentier, Benoit; Ranipeta, Ajay; Malczyk, Jeremy; Jetz, Walter

2018-03-01

Topographic variation underpins a myriad of patterns and processes in hydrology, climatology, geography and ecology and is key to understanding the variation of life on the planet. A fully standardized and global multivariate product of different terrain features has the potential to support many large-scale research applications, however to date, such datasets are unavailable. Here we used the digital elevation model products of global 250 m GMTED2010 and near-global 90 m SRTM4.1dev to derive a suite of topographic variables: elevation, slope, aspect, eastness, northness, roughness, terrain roughness index, topographic position index, vector ruggedness measure, profile/tangential curvature, first/second order partial derivative, and 10 geomorphological landform classes. We aggregated each variable to 1, 5, 10, 50 and 100 km spatial grains using several aggregation approaches. While a cross-correlation underlines the high similarity of many variables, a more detailed view in four mountain regions reveals local differences, as well as scale variations in the aggregated variables at different spatial grains. All newly-developed variables are available for download at Data Citation 1 and for download and visualization at http://www.earthenv.org/topography.

Combining 137Cs and topographic surveys for measuring soil erosion/deposition patterns in a rapidly accreting area

International Nuclear Information System (INIS)

Ritchie, J.C.

2000-01-01

Narrow, stiff grass hedges are biological barriers designed to slow runoff and capture soils carried in runoff water. This study was designed to measure quantitatively the deposition of soil up slope of a narrow, stiff grass hedge using topographic and 137 Cs surveys. Topographic surveys made in 1991, 1995, and 1998 measured 1 to 2 cm yr -1 of recent sediment deposited up slope of the grass hedge. 137 Cs analyses of soil samples were used to determine the medium-term (45 years) soil redistribution patterns. Erosion rates and patterns determined using 137 Cs measured medium-term erosion near the hedge do not reflect the recent deposition patterns near the grass hedge measured by topographic surveys. Using the combination of topographic and 137 Cs surveys allows a better understanding of the role of grass hedges as barriers for capturing eroding soils and suggest that the recent deposition is associated with the grass hedge but that there is still a net loss of soil near the hedge position over the past 45 years. (author)

Topographic separation of two sympatric palms in the central Amazon - does dispersal play a role?

Science.gov (United States)

Gomes de Freitas, Cintia; Capellotto Costa, Flávia Regina; Svenning, Jens-Christian; Balslev, Henrik

2012-02-01

Despite broadly overlapping geographic distributions in the central Amazon basin, two congeneric palm species (Attalea attaleoides and Attalea microcarpa) have topographically separated distributions on a local scale in Reserva Ducke near Manaus. Our aim here was to determine if this local scale separation can be linked to (1) seedling stage specialization to different habitat conditions of the two species, and/or (2) environmentally-controlled seed dispersal. We assessed the role of these potential drivers by mapping the local distribution of the two species over a 25-km2 grid and testing for correlation to seed removal and seed germination patterns using seed sowing experiments. 360 seeds of each species were sown in 30 uniformly distributed plots (12 seeds of each species in each plot), and seed removal and germination were subsequently monitored. Adult populations of the two species showed opposite distribution patterns linked to topography. However, there was little evidence for specialization to different habitat conditions at the seedling stage: after 11 months, 26.1% of seeds of A. microcarpa had germinated along the entire topographic gradient, albeit with a tendency toward higher germination in more inclined areas. For A. attaleoides, only 2.2% seeds had germinated, and again along the entire topographic gradient. In contrast, there was evidence for environmentally-controlled seed dispersal: for both species, seed removal was higher in flat areas. Presence of adults did not affect germination or seed removal. Our results suggest that topographically differentiated distributions of A. attaleoides and A. microcarpa may be reinforced by steep slope avoidance by their seed dispersers. A direct environmental control mechanism remains to be identified to explain the consistent topographic associations, but our results show that this mechanism does not work at the seed germination stage.

THE DESIGN AND PRODUCT OF NATIONAL 1:1000000 CARTOGRAPHIC DATA OF TOPOGRAPHIC MAP

Directory of Open Access Journals (Sweden)

G. Wang

2016-06-01

Full Text Available National administration of surveying, mapping and geoinformation started to launch the project of national fundamental geographic information database dynamic update in 2012. Among them, the 1:50000 database was updated once a year, furthermore the 1:250000 database was downsized and linkage-updated on the basis. In 2014, using the latest achievements of 1:250000 database, comprehensively update the 1:1000000 digital line graph database. At the same time, generate cartographic data of topographic map and digital elevation model data. This article mainly introduce national 1:1000000 cartographic data of topographic map, include feature content, database structure, Database-driven Mapping technology, workflow and so on.

Integrated Data Processing Methodology for Airborne Repeat-pass Differential SAR Interferometry

Science.gov (United States)

Dou, C.; Guo, H.; Han, C.; Yue, X.; Zhao, Y.

2014-11-01

Short temporal baseline and multiple ground deformation information can be derived from the airborne differential synthetic aperture radar Interforemetry (D-InSAR). However, affected by the turbulence of the air, the aircraft would deviate from the designed flight path with high frequent vibrations and changes both in the flight trajectory and attitude. Restricted by the accuracy of the position and orientation system (POS), these high frequent deviations can not be accurately reported, which would pose great challenges in motion compensation and interferometric process. Thus, these challenges constrain its wider applications. The objective of this paper is to investigate the accurate estimation and compensation of the residual motion errors in the airborne SAR imagery and time-varying baseline errors between the diffirent data acquirations, furthermore, to explore the integration data processing theory for the airborne D-InSAR system, and thus help to accomplish the correct derivation of the ground deformation by using the airborne D-InSAR measurements.

Occupational airborne exposure of the general population of a Norwegian county.

Science.gov (United States)

Bakke, P; Baste, V; Hanoa, R; Gulsvik, A

1992-02-01

Occupational airborne exposure was examined for a stratified sample (N = 1275) of the general population aged 18-73 years in Hordaland County, Norway. The subjects identified all jobs of more than six months since leaving school and stated whether they had been occupationally exposed to specific agents and work processes potentially harmful to the lungs. The prevalence in the population ever having been exposed was 18% for asbestos, 9% for quartz, 5% for aluminum dust, 6% for wood dust, 12% for metal gases, 12% for welding, 9% for soldering, and 1% for hairdressing. According to occupational title (last job), 3% of the population had held a job with a high degree of airborne exposure, 26% a job with moderate exposure, and 70% a job with no airborne exposure. During their worklife both the men and the women tended to leave polluted jobs more often than unpolluted jobs. Occupational exposure to airborne pollutants potentially harmful to the lungs is widespread in this Norwegian general population.

CryoSat-2 Validation using CryoVEX 2011-12 Airborne Campaigns

DEFF Research Database (Denmark)

Skourup, Henriette; Forsberg, René; Kildegaard Rose, Stine

Sat-2 by comparison to airborne and ground measurements. This is possible only through a major effort involving a large group of international partners. DTU Space has been involved in the CryoVEx campaigns with airborne activities since 2003. To validate the performance of the CryoSat-2 radar altimeter...... (SIRAL), the aircraft is equipped with an airborne version of the SIRAL altimeter (ASIRAS) together with a laser scanner. The campaigns are focused on five main validation sites: Devon ice cap (Canada), Austfonna ice cap (Svalbard), the EGIG line crossing the Greenland Ice Sheet, as well as the sea ice...... north of Alert and sea ice around Svalbard in the Fram Strait. Selected tracks were planned to match CryoSat-2 passes and a few of them were flown in formation flight with the Alfred Wegener Institute (AWI) Polar-5 carrying an EM-bird. This presentation summarizes the 2011-12 airborne campaigns...

Untangling Topographic and Climatic Forcing of Earthflow Motion

Science.gov (United States)

Finnegan, N. J.; Nereson, A. L.

2017-12-01

Earthflows commonly form in steep river canyons and are argued to initiate from rapid incision that destabilizes hill slope toes. At the same time, earthflows are known to exhibit a temporal pattern of movement that is correlated with seasonal precipitation and associated changes in effective stress. In this contribution, we use infinite slope analysis to illuminate the relative roles of topographic slope and climate (via its control on pore fluid pressure) in influencing earthflow motion at Oak Ridge earthflow, near San Jose, CA. To this end, we synthesize two years of shallow (2.7 m depth) pore fluid pressure data and continuous GPS-derived velocities with an 80-year record of historical deformation derived from tracking of trees and rocks on orthophotos along much of the 1.4 km length and 400 m relief of the earthflow. Multiple lines of evidence suggest that motion of Oak Ridge earthflow occurs as frictional sliding along a discrete failure surface, as argued for other earthflows. Spatial patterns of sliding velocity along the earthflow show the same sensitivity to topographic slope for five discrete periods of historical sliding, accelerating by roughly an order of magnitude along a 20 degree increase in earthflow gradient. In contrast, during the 2016-2017 winter, velocity increased much more rapidly for an equivalent increase in driving stress due to pore-fluid pressure rise at our GPS antenna. During this time period, Oak Ridge earthflow moved approximately 30 cm and we observed a relatively simple, non-linear relationship between GPS-derived sliding velocity and shallow pore fluid pressure. Rapid sliding in 2016-2017 (> 0.6 cm/day) occurred exclusively during the week following a large winter storm event that raised pore pressures to seasonal highs within only 1-2 days of the storm peak. These observations suggests that a mechanism, such as dilatant strengthening, acts to stabilize velocities for a given value of pore fluid pressure in the landslide mass

True Polar Wander of Enceladus From Topographic Data

Science.gov (United States)

Tajeddine, Radwan; Soderlund, Krista M.; Thomas, Peter C.; Helfenstein, Paul; Hedman, Matthew M.; Burns, Joseph A.; Schenk, Paul M.

2016-10-01

Besides the relative motion of lithospheric plates, the Earth as a whole moves with respect to its rotation pole, as shown by paleomagnetic, astrometric and geodetic measurements [1]. Such so-called true polar wander (TPW) occurs because our planet's moments of inertia change temporally owing to internal thermal convection and to the redistribution of surficial mass during ice ages. Thus, to conserve angular momentum while losing rotational energy, Earth's axis of maximum moment of inertia aligns with its spin axis. Theoreticians suspect similar reorientations of other celestial bodies but supporting evidence is fragmentary, at best [2]. Here we report the discovery of a global series of topographic lows on Saturn's satellite Enceladus indicating that this synchronously locked moon has undergone reorientation by ~55°. We use improved topographic data from spherical harmonic expansion of Cassini limb [3,4,5] and stereogrammetric [5,6,7] measurements to characterize regional topography over the surface of Enceladus. We identify a group of nearly antipodal basins orthogonal to a topographic basin chain tracing a non-equatorial circumglobal belt across Enceladus' surface. We argue that the belt and the antipodal regions are fossil remnants of old equator and poles, respectively. These lows are argued to arise from isostasic compensation [7,8] with their pattern reflecting variations in internal dynamics of the ice shell. Our hypothesis is consistent with many geological features visible in Cassini images [9].References:[1] Mitrovica, J.X. & Wahr, Annual Review of Earth and Planetary Sciences, 39, 577-616 (2011).[2] Matsuyama, I. et al. Annual Review of Earth and Planetary Sciences, 42, 605-634 (2014).[3] Thomas, P.C. et al. Icarus, 190, 573-584 (2007).[4] Thomas, P.C. Icarus, 208, 395-401 (2010).[5] Thomas, P.C. et al. Icarus, 264, 37-47 (2016).[6] Edwards, K. Photogrammetric Engineering and Remote Sensing, 53, 1219-1222 (1987).[7] Schenk, P.M. & McKinnon, W. B

Adaptive Restoration of Airborne Daedalus AADS1268 ATM Thermal Data

International Nuclear Information System (INIS)

D. Yuan; E. Doak; P. Guss; A. Will

2002-01-01

To incorporate the georegistration and restoration processes into airborne data processing in support of U.S. Department of Energy's nuclear emergency response task, we developed an adaptive restoration filter for airborne Daedalus AADS1268 ATM thermal data based on the Wiener filtering theory. Preliminary assessment shows that this filter enhances the detectability of small weak thermal anomalies in AADS1268 thermal images

Application of carbon nanotubes to topographical resolution enhancement of tapered fiber scanning near field optical microscopy probes

Science.gov (United States)

Huntington, S. T.; Jarvis, S. P.

2003-05-01

Scanning near field optical microscopy (SNOM) probes are typically tapered optical fibers with metallic coatings. The tip diameters are generally in excess of 300 nm and thus provide poor topographical resolution. Here we report on the attachment multiwalled carbon nanotubes to the probes in order to substantially enhance the topographical resolution, without adversely affecting the optical resolution.

Parametric estimation of time varying baselines in airborne interferometric SAR

DEFF Research Database (Denmark)

Mohr, Johan Jacob; Madsen, Søren Nørvang

1996-01-01

A method for estimation of time varying spatial baselines in airborne interferometric synthetic aperture radar (SAR) is described. The range and azimuth distortions between two images acquired with a non-linear baseline are derived. A parametric model of the baseline is then, in a least square...... sense, estimated from image shifts obtained by cross correlation of numerous small patches throughout the image. The method has been applied to airborne EMISAR imagery from the 1995 campaign over the Storstrommen Glacier in North East Greenland conducted by the Danish Center for Remote Sensing. This has...... reduced the baseline uncertainties from several meters to the centimeter level in a 36 km scene. Though developed for airborne SAR the method can easily be adopted to satellite data...

Airborne incidents : an econometric analysis of severity, December 31, 2014 : technical summary

Science.gov (United States)

2014-12-31

This is a technical summary of the Airborne Incidents: An Econometric Analysis of Severity main report. : Airborne loss of separation incidents occur when an aircraft breaches the defined separation limit (vertical and/or horizontal) with anoth...

Capabilities of current wildfire models when simulating topographical flow

Science.gov (United States)

Kochanski, A.; Jenkins, M.; Krueger, S. K.; McDermott, R.; Mell, W.

2009-12-01

Accurate predictions of the growth, spread and suppression of wild fires rely heavily on the correct prediction of the local wind conditions and the interactions between the fire and the local ambient airflow. Resolving local flows, often strongly affected by topographical features like hills, canyons and ridges, is a prerequisite for accurate simulation and prediction of fire behaviors. In this study, we present the results of high-resolution numerical simulations of the flow over a smooth hill, performed using (1) the NIST WFDS (WUI or Wildland-Urban-Interface version of the FDS or Fire Dynamic Simulator), and (2) the LES version of the NCAR Weather Research and Forecasting (WRF-LES) model. The WFDS model is in the initial stages of development for application to wind flow and fire spread over complex terrain. The focus of the talk is to assess how well simple topographical flow is represented by WRF-LES and the current version of WFDS. If sufficient progress has been made prior to the meeting then the importance of the discrepancies between the predicted and measured winds, in terms of simulated fire behavior, will be examined.

Non-allergic cutaneous reactions in airborne chemical sensitivity--a population based study

DEFF Research Database (Denmark)

Berg, Nikolaj Drimer; Linneberg, Allan; Thyssen, Jacob Pontoppidan

2011-01-01

the relationship between cutaneous reactions from patch testing and self-reported severity of chemical sensitivity to common airborne chemicals. A total of 3460 individuals participating in a general health examination, Health 2006, were patch tested with allergens from the European standard series and screened...... most severe groups of self-reported sensitivity to airborne chemicals. When adjusting for confounding, associations were weakened, and only non-allergic cutaneous reactions were significantly associated with individuals most severely affected by inhalation of airborne chemicals (odds ratio = 2.5, p = 0...

MIDWEST PROGRAM ON AIRBORNE TELEVISION INSTRUCTION -- A REGIONAL EXPLORATION IN EDUCATION.

Science.gov (United States)

IVEY, JOHN E.; AND OTHERS

STARTING IN FEBRUARY 1961, THE MIDWEST PROGRAM ON AIRBORNE TELEVISION INSTRUCTION (MPATI) TRANSMITTED COURSES IN FOREIGN LANGUAGES, SCIENCE, ARITHMETIC, ART, THE HUMANITIES, MUSIC, SOCIAL STUDIES, AND INTERNATIONAL RELATIONS TO 18 SCHOOLS IN THE MIDWEST. THE AIRBORNE TELECAST OPERATED OVER NORTH CENTRAL INDIANA AND TRANSMITTED COURSES OVER AN AREA…

Can airborne ultrasound monitor bubble size in chocolate?

International Nuclear Information System (INIS)

Watson, N; Hazlehurst, T; Povey, M; Vieira, J; Sundara, R; Sandoz, J-P

2014-01-01

Aerated chocolate products consist of solid chocolate with the inclusion of bubbles and are a popular consumer product in many countries. The volume fraction and size distribution of the bubbles has an effect on their sensory properties and manufacturing cost. For these reasons it is important to have an online real time process monitoring system capable of measuring their bubble size distribution. As these products are eaten by consumers it is desirable that the monitoring system is non contact to avoid food contaminations. In this work we assess the feasibility of using an airborne ultrasound system to monitor the bubble size distribution in aerated chocolate bars. The experimental results from the airborne acoustic experiments were compared with theoretical results for known bubble size distributions using COMSOL Multiphysics. This combined experimental and theoretical approach is used to develop a greater understanding of how ultrasound propagates through aerated chocolate and to assess the feasibility of using airborne ultrasound to monitor bubble size distribution in these systems. The results indicated that a smaller bubble size distribution would result in an increase in attenuation through the product

Lidar technologies for airborne and space-based applications

International Nuclear Information System (INIS)

Henson, T.D.; Schmitt, R.L.; Sobering, T.J.; Raymond, T.D.; Stephenson, D.A.

1994-10-01

This study identifies technologies required to extend the capabilities of airborne light detection and ranging (lidar) systems and establish the feasibility of autonomous space-based lidars. Work focused on technologies that enable the development of a lightweight, low power, rugged and autonomous Differential Absorption Lidar (DIAL) instruments. Applications for airborne or space-based DIAL include the measurement of water vapor profiles in support of climate research and processing-plant emissions signatures for environmental and nonproliferation monitoring. A computer-based lidar performance model was developed to allow trade studies to be performed on various technologies and system configurations. It combines input from the physics (absorption line strengths and locations) of the problem, the system requirements (weight, power, volume, accuracy), and the critical technologies available (detectors, lasers, filters) to produce the best conceptual design. Conceptual designs for an airborne and space-based water vapor DIAL, and a detailed design of a ground-based water vapor DIAL demonstration system were completed. Future work planned includes the final testing, integration, and operation of the demonstration system to prove the capability of the critical enabling technologies identified

Microbial Transformation of Dicarboxylic Acids by Airborne Bacteria

Science.gov (United States)

Cote, V.; Ariya, P.

2004-05-01

Organic aerosols are assumed to be key players in driving climatic changes and can cause health problems for human. Dicarboxylic acids (DCA) include a large fraction of identified important class of organic aerosols. In addition to direct sources, DCA are partly formed as the result of ozonolysis of terpenes and cyclic alkenes. Previous works in our laboratory show that airborne fungi collected from urban and suburban air play an important role in the transformation of severals organic aerosols such as DCA. Our present study focuses on understanding the potential chemical transformation induced by airborne bacteria and on identification of the transformation products. Airborne bacteria have been collected using a biosampler and cultivated on a solid media. Each bacterial colony is being tested by HPLC for their ability to transform DCA in liquid cultures. Also, GC-MS, SPME and NMR are being used to identify the metabolites generated from the transformation. We will present our preliminary results and we will discuss the application of bacterial activities on the chemical transformation of organics in atmosphere.

Can airborne ultrasound monitor bubble size in chocolate?

Science.gov (United States)

Watson, N.; Hazlehurst, T.; Povey, M.; Vieira, J.; Sundara, R.; Sandoz, J.-P.

2014-04-01

Aerated chocolate products consist of solid chocolate with the inclusion of bubbles and are a popular consumer product in many countries. The volume fraction and size distribution of the bubbles has an effect on their sensory properties and manufacturing cost. For these reasons it is important to have an online real time process monitoring system capable of measuring their bubble size distribution. As these products are eaten by consumers it is desirable that the monitoring system is non contact to avoid food contaminations. In this work we assess the feasibility of using an airborne ultrasound system to monitor the bubble size distribution in aerated chocolate bars. The experimental results from the airborne acoustic experiments were compared with theoretical results for known bubble size distributions using COMSOL Multiphysics. This combined experimental and theoretical approach is used to develop a greater understanding of how ultrasound propagates through aerated chocolate and to assess the feasibility of using airborne ultrasound to monitor bubble size distribution in these systems. The results indicated that a smaller bubble size distribution would result in an increase in attenuation through the product.

Electrospray Collection of Airborne Contaminants, Phase I

Data.gov (United States)

National Aeronautics and Space Administration — In stark contrast to current stagnation-based methods for capturing airborne particulates and biological aerosols, our demonstrated, cost-effective electrospray...

Airborne spread of foot-and-mouth disease - Model intercomparison

DEFF Research Database (Denmark)

Gloster, John; Jones, Andrew; Redington, Alison

2010-01-01

Foot-and-mouth disease virus (FMDV) spreads by direct contact between animals, by animal products (milk, meat and semen), by mechanical transfer on people or fomites and by the airborne route, with the relative importance of each mechanism depending on the particular outbreak characteristics....... Atmospheric dispersion models have been developed to assess airborne spread of FMDV in a number of countries, including the UK, Denmark, Australia, New Zealand, USA and Canada. These models were compared at a Workshop hosted by the Institute for Animal Health/Met Office in 2008. Each modeller was provided...... with data relating to the 1967 outbreak of FMD in Hampshire, UK, and asked to predict the spread of FMDV by the airborne route. A number of key issues emerged from the Workshop and subsequent modelling work: (1) in general all models predicted similar directions for livestock at risk, with much...

Analyzing Options for Airborne Emergency Wireless Communications

Energy Technology Data Exchange (ETDEWEB)

Michael Schmitt; Juan Deaton; Curt Papke; Shane Cherry

2008-03-01

In the event of large-scale natural or manmade catastrophic events, access to reliable and enduring commercial communication systems is critical. Hurricane Katrina provided a recent example of the need to ensure communications during a national emergency. To ensure that communication demands are met during these critical times, Idaho National Laboratory (INL) under the guidance of United States Strategic Command has studied infrastructure issues, concerns, and vulnerabilities associated with an airborne wireless communications capability. Such a capability could provide emergency wireless communications until public/commercial nodes can be systematically restored. This report focuses on the airborne cellular restoration concept; analyzing basic infrastructure requirements; identifying related infrastructure issues, concerns, and vulnerabilities and offers recommended solutions.

All-Fiber Airborne Coherent Doppler Lidar to Measure Wind Profiles

Directory of Open Access Journals (Sweden)

Liu Jiqiao

2016-01-01

Full Text Available An all-fiber airborne pulsed coherent Doppler lidar (CDL prototype at 1.54μm is developed to measure wind profiles in the lower troposphere layer. The all-fiber single frequency pulsed laser is operated with pulse energy of 300μJ, pulse width of 400ns and pulse repetition rate of 10kHz. To the best of our knowledge, it is the highest pulse energy of all-fiber eye-safe single frequency laser that is used in airborne coherent wind lidar. The telescope optical diameter of monostatic lidar is 100 mm. Velocity-Azimuth-Display (VAD scanning is implemented with 20 degrees elevation angle in 8 different azimuths. Real-time signal processing board is developed to acquire and process the heterodyne mixing signal with 10000 pulses spectra accumulated every second. Wind profiles are obtained every 20 seconds. Several experiments are implemented to evaluate the performance of the lidar. We have carried out airborne wind lidar experiments successfully, and the wind profiles are compared with aerological theodolite and ground based wind lidar. Wind speed standard error of less than 0.4m/s is shown between airborne wind lidar and balloon aerological theodolite.

Topographic Correction of Wind-driven Rainfall for Landslide Analysis in Central Taiwan with Validation from Aerial and Satellite Optical Images

Directory of Open Access Journals (Sweden)

Jin-King Liu

2013-05-01

Full Text Available Rainfall intensity plays an important role in landslide prediction especially in mountain areas. However, the rainfall intensity of a location is usually interpolated from rainfall recorded at nearby gauges without considering any possible effects of topographic slopes. In order to obtain reliable rainfall intensity for disaster mitigation, this study proposes a rainfall-vector projection method for topographic-corrected rainfall. The topographic-corrected rainfall is derived from wind speed, terminal velocity of raindrops, and topographical factors from digital terrain model. In addition, scatter plot was used to present landslide distribution with two triggering factors and kernel density analysis is adopted to enhance the perception of the distribution. Numerical analysis is conducted for a historic event, typhoon Mindulle, which occurred in 2004, in a location in central Taiwan. The largest correction reaches 11%, which indicates that topographic correction is significant. The corrected rainfall distribution is then applied to the analysis of landslide triggering factors. The result with corrected rainfall distribution provides better agreement with the actual landslide occurrence than the result without correction.

Government-industry conference on airborne radioiodine

International Nuclear Information System (INIS)

Burchsted, C.A.

1975-01-01

The Working Group on Airborne Radioiodine met at AEC Headquarters on March 28, 1974. Dr. Alex Perge gave the introduction for the Division of Waste Management and Transportation, noting the Commission hopes that private industry will take a bigger share in the future in funding and initiating needed research; that there should be a greater effort in the direction of reducing the quantity of material that becomes contaminated as an avenue toward reducing the airborne radioiodine problem, and toward reducing the waste generated to a form suitable for direct storage; and that the Commission must ensure valid bases for future regulations governing airborne releases and contamination. Dr. First discussed the background of the review committee and its outgrowth from the earlier organization meeting. He noted that its function will be the coordination of efforts concerned with the radioiodine problem and the dissemination of information and research data. A major objective of this meeting was to identify subjects for discussion at the Government-Industry Conference of Adsorbers and Adsorbents which will be held in conjunction with the 13th AEC Air Cleaning Conference in August. Mr. Dempsey noted that the gaseous effluent program had been inherited by WMT from the Division of Operational Safety, and that an important function of these continuing meetings of the Working Group will be to guide WMT in the expenditure of funds and assignment of research related to the radioiodine problem. (U.S.)

Topographical Short-Term Memory Differentiates Alzheimer's Disease From Frontotemporal Lobar Degeneration

NARCIS (Netherlands)

Bird, C.M.; Chan, D.; Hartley, T.; Pijnenburg, Y.A.L.; Rossor, M.N.; Burgess, N.

2010-01-01

We used a recently developed test of spatial memory-the Four Mountains Test-to investigate the core cognitive processes underpinning topographical disorientation in patients with amnestic mild cognitive impairment (a-MCI) and mild Alzheimer's disease (AD). Performance of these clinical groups was

Tracing the Base: A Topographic Test for Collusive Basing-Point Pricing

NARCIS (Netherlands)

Bos, Iwan; Schinkel, Maarten Pieter

2009-01-01

Basing-point pricing is known to have been abused by geographically dispersed firms in order to eliminate competition on transportation costs. This paper develops a topographic test for collusive basing-point pricing. The method uses transaction data (prices, quantities) and customer project site

Tracing the base: A topographic test for collusive basing-point pricing

NARCIS (Netherlands)

Bos, I.; Schinkel, M.P.

2008-01-01

Basing-point pricing is known to have been abused by geographically dispersed firms in order to eliminate competition on transportation costs. This paper develops a topographic test for collusive basing-point pricing. The method uses transaction data (prices, quantities) and customer project site

Topographic recording of the Slalom racing route in snow

Directory of Open Access Journals (Sweden)

V.F. Giovanis

2018-02-01

Full Text Available Purpose: The purpose of the present research was the study and evaluation of the theodolite’s (topographic speedometer use in tracing a path in slalom racing on snow conditions with 58 gates and also to record the optimal method of tracing a slalom route in relation to: a the "velocity" of the race track (degree of difficulty of slalom, b safety of tracing the slalom route. Methods: This research was based on methodology and measurements of a race track in giant slalom with 35 gates in the ski resort "3-5 Pigadia" of Naoussa - Greece. The topographic speedometer was fixed in place at the start of the route. From this point, measurements were taken, for the placement of all 58 gates throughout the route. The measurement was taken using the pole-prism, placed in each interior gate turn, at which the theodolite was aimed. With the help of topographic speedometer the following geometrical parameters have been registered: distance between the gates (Δs, altitude difference of points (Δh with an accuracy up to 1cm, terrain slope (θ, gate angular deviation (δ with an accuracy of up to 1 minute of the angle (°. This allows the creation of the top-view, side-view (profile and three-dimensional aspect of the track, under race conditions on snow and not on dry ground. Results: The correlation coefficient (r between the geometry factor (V.gs and average the above geometry parameters had the following respective values: V.gs -Ms = 0,15, V.gs -Mθ = - 0,52, V.gs -Mδ = - 0,29 for 58 gates on a level of statistical significance of p < 0,05. Conclusions: The first part comprised of 10 gates was the "fastest" (V.gs = 18 degrees of the total slalom route in Naoussa with 58 gates (V.gs = 14 degrees. With the above criteria, slaloms will be compared to each other and will be evaluated against age and safety.

3D Marine MT Modeling for a Topographic Seafloor

Science.gov (United States)

Zhang, B., Sr.; Yin, C.; Ren, X.; Liu, Y.; Huang, X.; Liu, L.

2017-12-01

As an effective geophysical tool, marine magnetotelluric (MMT) exploration has been widely used in offshore oil and gas exploration. Accordingly, the MMT forward modelling has made big progress. However, most of the researches are focused on a flat seafloor. In this paper, we present a 3D finite-element (FE) algorithm for marine MT forward modelling based on unstructured grids that can accurately model the MMT responses for a topographic seafloor. The boundary value problem for the forward modelling is described by an Helmholtz equation together with the boundary conditions derived by assuming the electrical polarizations respectively along the x- and y-direction on the top surface of the modelling domain. Applying the Galerkin method to the boundary value problem and substituting the unstructured finite-element vector shape function into the equation, we derive the final large linear system for the two polarizations, from which the EM fields is obtained for the calculation of impedance apparent resistivities and phases. To verify the effectiveness of our algorithm, we compare our modelling results with those by Key's (2013) 2D marine MT open source code of Scripps Institution of Oceanography (Figure 1). From Figure 1, one sees that the two agree well, implying that our 3D modelling method based unstructured FE is an effective modelling tool for topographic seafloor. From the MMT modelling responses for other topographic seafloor models (not shown here), we further observe that 1) the apparent resistivities have a similar profile pattern to the topography at the seafloor; 2) at the edges of the topography, there exist sharp changes; 3) the seafloor topography may dominate the responses from the abnormal bodies under the seafloor. This paper is supported by Key Program of National Natural Science Foundation of China (41530320), China Natural Science Foundation for Young Scientists (41404093), and Key National Research Project of China (2016YFC0303100, 2017YFC0601900)

Automated Detection of Salt Marsh Platforms : a Topographic Method

Science.gov (United States)

Goodwin, G.; Mudd, S. M.; Clubb, F. J.

2017-12-01

Monitoring the topographic evolution of coastal marshes is a crucial step toward improving the management of these valuable landscapes under the pressure of relative sea level rise and anthropogenic modification. However, determining their geometrically complex boundaries currently relies on spectral vegetation detection methods or requires labour-intensive field surveys and digitisation.We propose a novel method to reproducibly isolate saltmarsh scarps and platforms from a DEM. Field observations and numerical models show that saltmarshes mature into sub-horizontal platforms delineated by sub-vertical scarps: based on this premise, we identify scarps as lines of local maxima on a slope*relief raster, then fill landmasses from the scarps upward, thus isolating mature marsh platforms. Non-dimensional search parameters allow batch-processing of data without recalibration. We test our method using lidar-derived DEMs of six saltmarshes in England with varying tidal ranges and geometries, for which topographic platforms were manually isolated from tidal flats. Agreement between manual and automatic segregation exceeds 90% for resolutions of 1m, with all but one sites maintaining this performance for resolutions up to 3.5m. For resolutions of 1m, automatically detected platforms are comparable in surface area and elevation distribution to digitised platforms. We also find that our method allows the accurate detection of local bloc failures 3 times larger than the DEM resolution.Detailed inspection reveals that although tidal creeks were digitised as part of the marsh platform, automatic detection classifies them as part of the tidal flat, causing an increase in false negatives and overall platform perimeter. This suggests our method would benefit from a combination with existing creek detection algorithms. Fallen blocs and pioneer zones are inconsistently identified, particularly in macro-tidal marshes, leading to differences between digitisation and the automated method

Volatility of 210Po in airborne dusts in an atmosphere of nitrogen

International Nuclear Information System (INIS)

Abe, Michiko; Abe, Siro; Ikeda, Nagao.

1976-01-01

Volatilization behavior of 210 Po contained in airborne dusts in the temperature range of 200 - 800 0 C was investigated in an atmosphere of nitrogen. It was revealed that the volatilization of 210 Po in airborne dusts in an atmosphere of nitrogen as a function of temperature can be expressed in a stairlike shape with two steps. This tendency is similar to the previous results obtained in air. The previous and present data may suggest that 210 Po in airborne dusts consists of two or more different kinds of chemical species. (auth.)

Hardware Design for a Fixed-Wing Airborne Gravity Measurement System

Science.gov (United States)

1986-12-22

worldwide navigation system currently available that is sufficiently accurate for deter- mining Eotvos correction in airborne gravimetry is the Global...better in defining the strength of precipitation . The radar display is compact enough to be mounted on the cockpit, thus giving the pilots better...of the proposed AGMS version 3 MISCELLANEOUS AIRCRAFT CONSIDERATIONS Autopilot One of the most important considerations in airborne gravimetry is

Catchment-Scale Terrain Modelling with Structure-from-Motion Photogrammetry: a replacement for airborne lidar?

Science.gov (United States)

Brasington, James; James, Joe; Cook, Simon; Cox, Simon; Lotsari, Eliisa; McColl, Sam; Lehane, Niall; Williams, Richard; Vericat, Damia

2016-04-01

In recent years, 3D terrain reconstructions based on Structure-from-Motion photogrammetry have dramatically democratized the availability of high quality topographic data. This approach involves the use of a non-linear bundle adjustment to estimate simultaneously camera position, pose, distortion and 3D model coordinates. In contrast to traditional aerial photogrammetry, the bundle adjustment is typically solved without external constraints and instead ground control is used a posteriori to transform the modelled coordinates to an established datum using a similarity transformation. The limited data requirements, coupled with the ability to self-calibrate compact cameras, has led to a burgeoning of applications using low-cost imagery acquired terrestrially or from low-altitude platforms. To date, most applications have focused on relatively small spatial scales (0.1-5 Ha), where relaxed logistics permit the use of dense ground control networks and high resolution, close-range photography. It is less clear whether this low-cost approach can be successfully upscaled to tackle larger, watershed-scale projects extending over 102-3 km2 where it could offer a competitive alternative to established landscape modelling with airborne lidar. At such scales, compromises over the density of ground control, the speed and height of sensor platform and related image properties are inevitable. In this presentation we provide a systematic assessment of the quality of large-scale SfM terrain products derived for over 80 km2 of the braided Dart River and its catchment in the Southern Alps of NZ. Reference data in the form of airborne and terrestrial lidar are used to quantify the quality of 3D reconstructions derived from helicopter photography and used to establish baseline uncertainty models for geomorphic change detection. Results indicate that camera network design is a key determinant of model quality, and that standard aerial photogrammetric networks based on strips of nadir

Development of unauthorized airborne emission source identification procedure

Science.gov (United States)

Shtripling, L. O.; Bazhenov, V. V.; Varakina, N. S.; Kupriyanova, N. P.

2018-01-01

The paper presents the procedure for searching sources of unauthorized airborne emissions. To make reasonable regulation decisions on airborne pollutant emissions and to ensure the environmental safety of population, the procedure provides for the determination of a pollutant mass emission value from the source being the cause of high pollution level and the search of a previously unrecognized contamination source in a specified area. To determine the true value of mass emission from the source, the minimum of the mean-root-square mismatch criterion between the computed and measured pollutant concentration in the given location is used.

Manual of respiratory protection against airborne radioactive materials

International Nuclear Information System (INIS)

Caplin, J.L.; Held, B.J.; Catlin, R.J.

1976-10-01

The manual supplements Regulatory Guide 8.15, ''Acceptable Programs for Respiratory Protection''. It provides broad guidance for the planned use of respirators to protect individuals from airborne radioactive materials that might be encountered during certain operations. The guidance is intended for use by management in establishing and supervising programs and by operating personnel in implementing programs. Guidance is primarily directed to the use of respirators to prevent the inhalation of airborne radioactive materials. Protection against other modes of intake (e.g., absorption, swallowing, wound injection) is, in general, not covered nor is the use of protective equipment for head, eye, or skin protection

Simulation and Analysis of Topographic Effect on Land Surface Albedo over Mountainous Areas

Science.gov (United States)

Hao, D.; Wen, J.; Xiao, Q.

2017-12-01

Land surface albedo is one of the significant geophysical variables affecting the Earth's climate and controlling the surface radiation budget. Topography leads to the formation of shadows and the redistribution of incident radiation, which complicates the modeling and estimation of the land surface albedo. Some studies show that neglecting the topography effect may lead to significant bias in estimating the land surface albedo for the sloping terrain. However, for the composite sloping terrain, the topographic effects on the albedo remain unclear. Accurately estimating the sub-topographic effect on the land surface albedo over the composite sloping terrain presents a challenge for remote sensing modeling and applications. In our study, we focus on the development of a simplified estimation method for land surface albedo including black-sky albedo (BSA) and white-sky albedo (WSA) of the composite sloping terrain at a kilometer scale based on the fine scale DEM (30m) and quantitatively investigate and understand the topographic effects on the albedo. The albedo is affected by various factors such as solar zenith angle (SZA), solar azimuth angle (SAA), shadows, terrain occlusion, and slope and aspect distribution of the micro-slopes. When SZA is 30°, the absolute and relative deviations between the BSA of flat terrain and that of rugged terrain reaches 0.12 and 50%, respectively. When the mean slope of the terrain is 30.63° and SZA=30°, the absolute deviation of BSA caused by SAA can reach 0.04. The maximal relative and relative deviation between the WSA of flat terrain and that of rugged terrain reaches 0.08 and 50%. These results demonstrate that the topographic effect has to be taken into account in the albedo estimation.

Airborne Geophysical/Geological Mineral Inventory CIP Program

National Research Council Canada - National Science Library

1999-01-01

The Airborne-Geophysical/Geological Mineral Inventory project is a special multi-year investment to expand the knowledge base of Alaska's mineral resources and catalyze private-sector mineral development...

US Topo—Topographic maps for the Nation

Science.gov (United States)

Fishburn, Kristin A.; Carswell, William J.

2017-06-23

Building on the success of 125 years of mapping, the U.S. Geological Survey created US Topo, a georeferenced digital map produced from The National Map data. US Topo maps are designed to be used like the traditional 7.5-minute quadrangle paper topographic maps for which the U.S. Geological Survey is so well known. However, in contrast to paper-based maps, US Topo maps provide modern technological advantages that support faster, wider public distribution and basic, onscreen geospatial analysis, including the georeferencing capability to display the ground coordinate location as the user moves the cursor around the map.

Dense image matching of terrestrial imagery for deriving high-resolution topographic properties of vegetation locations in alpine terrain

Science.gov (United States)

Niederheiser, R.; Rutzinger, M.; Bremer, M.; Wichmann, V.

2018-04-01

The investigation of changes in spatial patterns of vegetation and identification of potential micro-refugia requires detailed topographic and terrain information. However, mapping alpine topography at very detailed scales is challenging due to limited accessibility of sites. Close-range sensing by photogrammetric dense matching approaches based on terrestrial images captured with hand-held cameras offers a light-weight and low-cost solution to retrieve high-resolution measurements even in steep terrain and at locations, which are difficult to access. We propose a novel approach for rapid capturing of terrestrial images and a highly automated processing chain for retrieving detailed dense point clouds for topographic modelling. For this study, we modelled 249 plot locations. For the analysis of vegetation distribution and location properties, topographic parameters, such as slope, aspect, and potential solar irradiation were derived by applying a multi-scale approach utilizing voxel grids and spherical neighbourhoods. The result is a micro-topography archive of 249 alpine locations that includes topographic parameters at multiple scales ready for biogeomorphological analysis. Compared with regional elevation models at larger scales and traditional 2D gridding approaches to create elevation models, we employ analyses in a fully 3D environment that yield much more detailed insights into interrelations between topographic parameters, such as potential solar irradiation, surface area, aspect and roughness.

2012 USACE Post Sandy Topographic LiDAR: Rhode Island and Massachusetts Coast

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — This topographic elevation point data derived from multiple return light detection and ranging (LiDAR) represents 354.272 square miles of coastline for Rhode Island...

Topographical characteristics and principal component structure of the hypnagogic EEG.

Science.gov (United States)

Tanaka, H; Hayashi, M; Hori, T

1997-07-01

The purpose of the present study was to identify the dominant topographic components of electroencephalographs (EEG) and their behavior during the waking-sleeping transition period. Somnography of nocturnal sleep was recorded on 10 male subjects. Each recording, from "lights-off" to 5 minutes after the appearance of the first sleep spindle, was analyzed. The typical EEG patterns during hypnagogic period were classified into nine EEG stages. Topographic maps demonstrated that the dominant areas of alpha-band activity moved from the posterior areas to anterior areas along the midline of the scalp. In delta-, theta-, and sigma-band activities, the differences of EEG amplitude between the focus areas (the dominant areas) and the surrounding areas increased as a function of EEG stage. To identify the dominant topographic components, a principal component analysis was carried out on a 12-channel EEG data set for each of six frequency bands. The dominant areas of alpha 2- (9.6-11.4 Hz) and alpha 3- (11.6-13.4 Hz) band activities moved from the posterior to anterior areas, respectively. The distribution of alpha 2-band activity on the scalp clearly changed just after EEG stage 3 (alpha intermittent, < 50%). On the other hand, alpha 3-band activity became dominant in anterior areas after the appearance of vertex sharp-wave bursts (EEG stage 7). For the sigma band, the amplitude of extensive areas from the frontal pole to the parietal showed a rapid rise after the onset of stage 7 (the appearance of vertex sharp-wave bursts). Based on the results, sleep onset process probably started before the onset of sleep stage 1 in standard criteria. On the other hand, the basic sleep process may start before the onset of sleep stage 2 or the manually scored spindles.

Topographic variations in chaos on Europa: Implications for diapiric formation

Science.gov (United States)

Schenk, Paul M.; Pappalardo, Robert T.

2004-01-01

Disrupted terrain, or chaos, on Europa, might have formed through melting of a floating ice shell from a subsurface ocean [Cam et al., 1998; Greenberg et al., 19991, or breakup by diapirs rising from the warm lower portion of the ice shell [Head and Pappalardo, 1999; Collins et al., 20001. Each model makes specific and testable predictions for topographic expression within chaos and relative to surrounding terrains on local and regional scales. High-resolution stereo-controlled photoclinometric topography indicates that chaos topography, including the archetypal Conamara Chaos region, is uneven and commonly higher than surrounding plains by up to 250 m. Elevated and undulating topography is more consistent with diapiric uplift of deep material in a relatively thick ice shell, rather than melt-through and refreezing of regionally or globally thin ice by a subsurface ocean. Vertical and horizontal scales of topographic doming in Conamara Chaos are consistent with a total ice shell thickness >15 km. Contact between Europa's ocean and surface may most likely be indirectly via diapirism or convection.

Optimization of airborne wind energy generators

NARCIS (Netherlands)

Fagiano, L.; Milanese, M.; Piga, D.

2012-01-01

This paper presents novel results related to an innovative airborne wind energy technology, named Kitenergy, for the conversion of high-altitude wind energy into electricity. The research activities carried out in the last five years, including theoretical analyses, numerical simulations, and

Topology optimized cloak for airborne sound

DEFF Research Database (Denmark)

Andkjær, Jacob Anders; Sigmund, Ole

2013-01-01

Directional acoustic cloaks that conceal an aluminum cylinder for airborne sound waves are presented in this paper. Subwavelength cylindrical aluminum inclusions in air constitute the cloak design to aid practical realizations. The positions and radii of the subwavelength cylinders are determined...

The risk of airborne influenza transmission in passenger cars.

Science.gov (United States)

Knibbs, L D; Morawska, L; Bell, S C

2012-03-01

Travel in passenger cars is a ubiquitous aspect of the daily activities of many people. During the 2009 influenza A(H1N1) pandemic a case of probable transmission during car travel was reported in Australia, to which spread via the airborne route may have contributed. However, there are no data to indicate the likely risks of such events, and how they may vary and be mitigated. To address this knowledge gap, we estimated the risk of airborne influenza transmission in two cars (1989 model and 2005 model) by employing ventilation measurements and a variation of the Wells-Riley model. Results suggested that infection risk can be reduced by not recirculating air; however, estimated risk ranged from 59% to 99·9% for a 90-min trip when air was recirculated in the newer vehicle. These results have implications for interrupting in-car transmission of other illnesses spread by the airborne route.

Airborne campaigns for CryoSat prelaunch calibration and validation

DEFF Research Database (Denmark)

Skourup, Henriette; Hanson, Susanne; Hvidegaard, Sine Munk

2011-01-01

After the successful launch of CryoSat-2 in April 2010, the first direct validation campaign of the satellite is planned for spring 2011. DTU Space has been involved in ESA’s CryoSat Validation Experiment (CryoVEx) with airborne activities since 2003. To validate the prelaunch performance...... of the CryoSat radar altimeter (SIRAL), an airborne version of the SIRAL altimeter (ASIRAS) has been flown together with a laser scanner in 2006 and 2008. Of particular interest is to study the penetration depth of the radar altimeter over both land- and sea ice. This can be done by comparing the radar...... and laser measurements with in situ observations. Here, an overview of the prelaunch airborne campaigns is given, together with results of the ASIRAS performance over land- and sea ice. The observations, used in this study, are obtained from the Greenland ice sheet and from both multiyear and first year sea...

Subsetting Tools for Enabling Easy Access to International Airborne Chemistry Data

Science.gov (United States)

Northup, E. A.; Chen, G.; Quam, B. M.; Beach, A. L., III; Silverman, M. L.; Early, A. B.

2017-12-01

In response to the Research Opportunities in Earth and Space Science (ROSES) 2015 release announcement for Advancing Collaborative Connections for Earth System Science (ACCESS), researchers at NASA Langley Research Center (LaRC) proposed to extend the capabilities of the existing Toolsets for Airborne Data (TAD) to include subsetting functionality to allow for easier access to international airborne field campaign data. Airborne field studies are commonly used to gain a detailed understanding of atmospheric processes for scientific research on international climate change and air quality issues. To accommodate the rigorous process for manipulating airborne field study chemistry data, and to lessen barriers for researchers, TAD was created with the ability to geolocate data from various sources measured on different time scales from a single flight. The analysis of airborne chemistry data typically requires data subsetting, which can be challenging and resource-intensive for end users. In an effort to streamline this process, new data subsetting features and updates to the current database model will be added to the TAD toolset. These will include two subsetters: temporal and spatial, and vertical profile. The temporal and spatial subsetter will allow users to both focus on data from a specific location and/or time period. The vertical profile subsetter will retrieve data collected during an individual aircraft ascent or descent spiral. These new web-based tools will allow for automation of the typically labor-intensive manual data subsetting process, which will provide users with data tailored to their specific research interests. The system has been designed to allow for new in-situ airborne missions to be added as they become available, with only minor pre-processing required. The development of these enhancements will be discussed in this presentation.

Characteristics of Airborne Particulates Containing Naturally Occurring Radioactive Materials in Monazite Industry

Energy Technology Data Exchange (ETDEWEB)

Kim, Yong Geon; Choi, Cheol Kyu; Park, Il; Kim, Min Jun; Go, A Ra; Ji, Seung Woo; Kim, Kwang Pyo [Kyunghee University, Yongin (Korea, Republic of); Koo, Bon Cheol [KINS, Daejeon (Korea, Republic of)

2016-05-15

The objective of this study was to characterize physicochemical properties of airborne particulates at a monazite pulverization industry. The properties included particulate size distribution, concentration, shape, density, and radioactivity concentration. Monazite is one of the minerals containing naturally occurring radioactive material (NORM). Therefore, external and internal exposure can be occurred to the workers in monazite industry. The major exposure pathway of the workers is internal exposure due to inhalation of airborne particulates. According to International Commission on Radiological Protection (ICRP), radiation dose due to inhaled particulates containing NORM depends on particulate properties. Therefore, ICRP recommended the internal dose assessment using measured physicochemical properties of the airborne particulates. In the absence of specific information, ICRP provided default reference values. In this study, we characterized physicochemical properties of airborne particulates at a monazite pulverization industry. The databases of particulate information can be used for accurate internal dose assessment of worker.

Topographic outcomes after corneal collagen crosslinking in progressive keratoconus: 1-year follow-up

Directory of Open Access Journals (Sweden)

Mauro C. Tiveron Jr

Full Text Available ABSTRACT Purpose: We aimed to report and analyze topographic and refractive outcomes following corneal collagen crosslinking (CXL in patients with progressive keratoconus (KC. Methods: We performed a retrospective, analytical, and observational study of 100 eyes from 74 progressive KC patients who underwent CXL at the Eye Hospital of Paraná. Keratometric values were analyzed preoperatively as well as 3 and 12 months postoperatively. Results: For a total of 100 eyes, 68 belonged to male patients. The mean age of our study population was 19.9 ± 5.61 years. The average visual acuity and topographic parameters overall were stable after 1 year (p<0.05. After 3 months, steepest keratometry reading (K2 and maximum keratometry (Kmax were significantly decreased (p<0.05. Regarding topographic astigmatism (dK, there was no significant difference between the 3-month and 12-month follow-ups. When we made comparisons between genders following CXL, there were no significant differences related to the changes in Kmax, K2, and spectacle-corrected distance visual acuity (SCDVA. Conclusions: CXL promoted stabilization or improvement of keratometric values and visual acuity. We found that keratoconus apex stability may be achieved 3 months after the procedure. There was no significant difference in keratometric and refractive values measured between male and female patients.

Using UAV photogrammetry to study topographic change: application to Saskatchewan Glacier, Alberta, Canada

Science.gov (United States)

Meunier Cardinal, G.; Demuth, M. N.; Kinnard, C.

2016-12-01

Glaciers are an important source of fresh water in the headwaters of the Canadian Rocky Mountains, and ongoing climate warming could reduce their future hydrological contribution. Unmanned Aerial Vehicles UAVs) are an emergent technology that allow studying glacial processes with an unprecedented level of detail, but their usefulness for deriving accurate topographic data on glaciers has not yet been fully assessed. In this perspective we tested the use of a UAV platform to acquire images at a very high spatial resolution (using the Structure from Motion (SfM) algorithm. A detailed assessment of DEM errors was performed by cross-validation of an network of ground control points (GCPs) deployed on the glacier surface. The influence of checkpoint position in the network, border effects, number of photos calibrated and GPS accuracy were examined. Topographical changes were measured from the DEM difference and surface displacements estimated by applying feature tracking techniques to the orthomosaics. Further, the dominant scales of topographic spatial variability were examined using a semivariogram analysis of the DEMs. Results show that UAV-based photogrammetry is promising to further our understanding of high-resolution glacier surface processes and to perform repeat, on-demand monitoring of glacier changes, but their application on remote glaciers remains challenging.

The theoretical study of full spectrum analysis method for airborne gamma-ray spectrometric data

International Nuclear Information System (INIS)

Ni Weichong

2011-01-01

Spectra of airborne gamma-ray spectrometry was found to be the synthesis of spectral components of radioelement sources by analyzing the constitution of radioactive sources for airborne gamma-ray spectrometric survey and establishing the models of gamma-ray measurement. The mathematical equation for analysising airborne gamma-ray full spectrometric data can be expressed into matrix and related expansions were developed for the mineral resources exploration, environmental radiation measurement, nuclear emergency monitoring, and so on. Theoretical study showed that the atmospheric radon could be directly computed by airborne gamma-ray spectrometric data with full spectrum analysis without the use of the accessional upward-looking detectors. (authors)

Landslide Change Detection Based on Multi-Temporal Airborne LiDAR-Derived DEMs

Directory of Open Access Journals (Sweden)

Omar E. Mora

2018-01-01

Full Text Available Remote sensing technologies have seen extraordinary improvements in both spatial resolution and accuracy recently. In particular, airborne laser scanning systems can now provide data for surface modeling with unprecedented resolution and accuracy, which can effectively support the detection of sub-meter surface features, vital for landslide mapping. Also, the easy repeatability of data acquisition offers the opportunity to monitor temporal surface changes, which are essential to identifying developing or active slides. Specific methods are needed to detect and map surface changes due to landslide activities. In this paper, we present a methodology that is based on fusing probabilistic change detection and landslide surface feature extraction utilizing multi-temporal Light Detection and Ranging (LiDAR derived Digital Elevation Models (DEMs to map surface changes demonstrating landslide activity. The proposed method was tested in an area with numerous slides ranging from 200 m2 to 27,000 m2 in area under low vegetation and tree cover, Zanesville, Ohio, USA. The surface changes observed are probabilistically evaluated to determine the likelihood of the changes being landslide activity related. Next, based on surface features, a Support Vector Machine (SVM quantifies and maps the topographic signatures of landslides in the entire area. Finally, these two processes are fused to detect landslide prone changes. The results demonstrate that 53 out of 80 inventory mapped landslides were identified using this method. Additionally, some areas that were not mapped in the inventory map displayed changes that are likely to be developing landslides.

Identification of distinct topographical surface microstructures favoring either undifferentiated expansion or differentiation of murine embryonic stem cells.

Science.gov (United States)

Markert, Lotte D'Andrea; Lovmand, Jette; Foss, Morten; Lauridsen, Rune Hoff; Lovmand, Michael; Füchtbauer, Ernst-Martin; Füchtbauer, Annette; Wertz, Karin; Besenbacher, Flemming; Pedersen, Finn Skou; Duch, Mogens

2009-11-01

The potential of embryonic stem (ES) cells for both self-renewal and differentiation into cells of all three germ layers has generated immense interest in utilizing these cells for tissue engineering or cell-based therapies. However, the ability to culture undifferentiated ES cells without the use of feeder cells as well as means to obtain homogeneous, differentiated cell populations devoid of residual pluripotent ES cells still remain major challenges. Here we have applied murine ES cells to topographically microstructured surface libraries, BioSurface Structure Arrays (BSSA), and investigated whether these could be used to (i) identify topographically microstructured growth supports alleviating the need for feeder cells for expansion of undifferentiated ES cells and (ii) identify specific types of microstructures enforcing differentiation of ES cells. The BSSA surfaces arrays consisted of 504 different topographical microstructures each located in a tester field of 3 x 3 mm. The murine ES cell lines CJ7 and KH2 were seeded upon the BSSA libraries and specific topographical structures facilitating either undifferentiated ES cell growth or enhancing spreading indicative of differentiation of the ES cells were identified. Secondly serial passage of undifferentiated CJ7 ES cells on selected microstructures, identified in the screening of these BSSA libraries, showed that these cells had retained germ-line potential. These results indicate that one specific type of topographical surface microstructures, identified by the BSSA technology, can substitute for feeder cells and that another subset may be used to eliminate undifferentiated ES cells from a population of differentiated ES cells.

Geophex Airborne Unmanned Survey System

International Nuclear Information System (INIS)

Won, I.L.; Keiswetter, D.

1995-01-01

Ground-based surveys place personnel at risk due to the proximity of buried unexploded ordnance (UXO) items or by exposure to radioactive materials and hazardous chemicals. The purpose of this effort is to design, construct, and evaluate a portable, remotely-piloted, airborne, geophysical survey system. This non-intrusive system will provide stand-off capability to conduct surveys and detect buried objects, structures, and conditions of interest at hazardous locations. During a survey, the operators remain remote from, but within visual distance of, the site. The sensor system never contacts the Earth, but can be positioned near the ground so that weak geophysical anomalies can be detected. The Geophex Airborne Unmanned Survey System (GAUSS) is designed to detect and locate small-scale anomalies at hazardous sites using magnetic and electromagnetic survey techniques. The system consists of a remotely-piloted, radio-controlled, model helicopter (RCH) with flight computer, light-weight geophysical sensors, an electronic positioning system, a data telemetry system, and a computer base-station. The report describes GAUSS and its test results

Geophex Airborne Unmanned Survey System

Energy Technology Data Exchange (ETDEWEB)

Won, I.L.; Keiswetter, D.

1995-12-31

Ground-based surveys place personnel at risk due to the proximity of buried unexploded ordnance (UXO) items or by exposure to radioactive materials and hazardous chemicals. The purpose of this effort is to design, construct, and evaluate a portable, remotely-piloted, airborne, geophysical survey system. This non-intrusive system will provide stand-off capability to conduct surveys and detect buried objects, structures, and conditions of interest at hazardous locations. During a survey, the operators remain remote from, but within visual distance of, the site. The sensor system never contacts the Earth, but can be positioned near the ground so that weak geophysical anomalies can be detected. The Geophex Airborne Unmanned Survey System (GAUSS) is designed to detect and locate small-scale anomalies at hazardous sites using magnetic and electromagnetic survey techniques. The system consists of a remotely-piloted, radio-controlled, model helicopter (RCH) with flight computer, light-weight geophysical sensors, an electronic positioning system, a data telemetry system, and a computer base-station. The report describes GAUSS and its test results.

LBA-ECO LC-01 Topographic Data for Intensive Study Areas, Northern Ecuadorian Amazon

Data.gov (United States)

National Aeronautics and Space Administration — ABSTRACT: This data set contains topographic/geomorphological data associated with the four Intensive Study Areas (ISAs) in the Northern Ecuadorian Amazon (northern...

LBA-ECO LC-01 Topographic Data for Intensive Study Areas, Northern Ecuadorian Amazon

Data.gov (United States)

National Aeronautics and Space Administration — This data set contains topographic/geomorphological data associated with the four Intensive Study Areas (ISAs) in the Northern Ecuadorian Amazon (northern Oriente)...

THE TOPOGRAPHIC DATA DELUGE – COLLECTING AND MAINTAINING DATA IN A 21ST CENTURY MAPPING AGENCY

Directory of Open Access Journals (Sweden)

D. A. Holland

2016-06-01

Full Text Available In the last few years, the number of sensors and data collection systems available to a mapping agency has grown considerably. In the field, in addition to total stations measuring position, angles and distances, the surveyor can choose from hand-held GPS devices, multi-lens imaging systems or laser scanners, which may be integrated with a laptop or tablet to capture topographic data directly in the field. These systems are joined by mobile mapping solutions, mounted on large or small vehicles, or sometimes even on a backpack carried by a surveyor walking around a site. Such systems allow the raw data to be collected rapidly in the field, while the interpretation of the data can be performed back in the office at a later date. In the air, large format digital cameras and airborne lidar sensors are being augmented with oblique camera systems, taking multiple views at each camera position and being used to create more realistic 3D city models. Lower down in the atmosphere, Unmanned Aerial Vehicles (or Remotely Piloted Aircraft Systems have suddenly become ubiquitous. Hundreds of small companies have sprung up, providing images from UAVs using ever more capable consumer cameras. It is now easy to buy a 42 megapixel camera off the shelf at the local camera shop, and Canon recently announced that they are developing a 250 megapixel sensor for the consumer market. While these sensors may not yet rival the metric cameras used by today’s photogrammetrists, the rapid developments in sensor technology could eventually lead to the commoditization of high-resolution camera systems. With data streaming in from so many sources, the main issue for a mapping agency is how to interpret, store and update the data in such a way as to enable the creation and maintenance of the end product. This might be a topographic map, ortho-image or a digital surface model today, but soon it is just as likely to be a 3D point cloud, textured 3D mesh, 3D city model, or

Application of porous foams for size-selective measurements of airborne wheat allergen

NARCIS (Netherlands)

Bogdanovic, J.; Pater, A.J. de; Doekes, G.; Wouters, I.M.; Heederik, D.J.J.

2006-01-01

Background: Exposure to airborne wheat allergen is a well-known cause of bakers' allergy and asthma. Airborne wheat allergen can be measured by enzyme immunoassays (EIAs) in extracts of inhalable dust samples, but only limited knowledge is available on the size distribution of wheat

Pig Farmers’ Homes Harbor More Diverse Airborne Bacterial Communities Than Pig Stables or Suburban Homes

Directory of Open Access Journals (Sweden)

Ditte V. Vestergaard

2018-05-01

Full Text Available Airborne bacterial communities are subject to conditions ill-suited to microbial activity and growth. In spite of this, air is an important transfer medium for bacteria, with the bacteria in indoor air having potentially major consequences for the health of a building’s occupants. A major example is the decreased diversity and altered composition of indoor airborne microbial communities as a proposed explanation for the increasing prevalence of asthma and allergies worldwide. Previous research has shown that living on a farm confers protection against development of asthma and allergies, with airborne bacteria suggested as playing a role in this protective effect. However, the composition of this beneficial microbial community has still not been identified. We sampled settled airborne dust using a passive dust sampler from Danish pig stables, associated farmers’ homes, and from suburban homes (267 samples in total and carried out quantitative PCR measurements of bacterial abundance and MiSeq sequencing of the V3–V4 region of bacterial 16S rRNA genes found in these samples. Airborne bacteria had a greater diversity and were significantly more abundant in pig stables and farmers’ homes than suburban homes (Wilcoxon rank sum test P < 0.05. Moreover, bacterial taxa previously suggested to contribute to a protective effect had significantly higher relative and absolute abundance in pig stables and farmers’ homes than in suburban homes (ALDEx2 with P < 0.05, including Firmicutes, Peptostreptococcaceae, Prevotellaceae, Lachnospiraceae, Ruminococcaceae, Ruminiclostridium, and Lactobacillus. Pig stables had significantly lower airborne bacterial diversity than farmers’ homes, and there was no discernable direct transfer of airborne bacteria from stable to home. This study identifies differences in indoor airborne bacterial communities that may be an important component of this putative protective effect, while showing that pig stables

Pig Farmers’ Homes Harbor More Diverse Airborne Bacterial Communities Than Pig Stables or Suburban Homes

Science.gov (United States)

Vestergaard, Ditte V.; Holst, Gitte J.; Basinas, Ioannis; Elholm, Grethe; Schlünssen, Vivi; Linneberg, Allan; Šantl-Temkiv, Tina; Finster, Kai; Sigsgaard, Torben; Marshall, Ian P. G.

2018-01-01

Airborne bacterial communities are subject to conditions ill-suited to microbial activity and growth. In spite of this, air is an important transfer medium for bacteria, with the bacteria in indoor air having potentially major consequences for the health of a building’s occupants. A major example is the decreased diversity and altered composition of indoor airborne microbial communities as a proposed explanation for the increasing prevalence of asthma and allergies worldwide. Previous research has shown that living on a farm confers protection against development of asthma and allergies, with airborne bacteria suggested as playing a role in this protective effect. However, the composition of this beneficial microbial community has still not been identified. We sampled settled airborne dust using a passive dust sampler from Danish pig stables, associated farmers’ homes, and from suburban homes (267 samples in total) and carried out quantitative PCR measurements of bacterial abundance and MiSeq sequencing of the V3–V4 region of bacterial 16S rRNA genes found in these samples. Airborne bacteria had a greater diversity and were significantly more abundant in pig stables and farmers’ homes than suburban homes (Wilcoxon rank sum test P < 0.05). Moreover, bacterial taxa previously suggested to contribute to a protective effect had significantly higher relative and absolute abundance in pig stables and farmers’ homes than in suburban homes (ALDEx2 with P < 0.05), including Firmicutes, Peptostreptococcaceae, Prevotellaceae, Lachnospiraceae, Ruminococcaceae, Ruminiclostridium, and Lactobacillus. Pig stables had significantly lower airborne bacterial diversity than farmers’ homes, and there was no discernable direct transfer of airborne bacteria from stable to home. This study identifies differences in indoor airborne bacterial communities that may be an important component of this putative protective effect, while showing that pig stables themselves do not appear