Process for decontaminating objects having radio-active layers of wall

International Nuclear Information System (INIS)

Groessler, P.

1980-01-01

In order to reduce the parts of walls found when decommissioning a nuclear power station in size and be able to transport them in protective containers, an explosion is carried out on the side of the wall opposite the contaminated layers. These layers therefore peel off. Explosives in the form of plates or liquid explosives are used flexibly. (DG) [de

Regulatory inspection of nuclear facilities and enforcement by the regulatory body. Safety guide

International Nuclear Information System (INIS)

2002-01-01

The purpose of this Safety Guide is to provide recommendations for regulatory bodies on the inspection of nuclear facilities, regulatory enforcement and related matters. The objective is to provide the regulatory body with a high level of confidence that operators have the processes in place to ensure compliance and that they do comply with legal requirements, including meeting the safety objectives and requirements of the regulatory body. However, in the event of non-compliance, the regulatory body should take appropriate enforcement action. This Safety Guide covers regulatory inspection and enforcement in relation to nuclear facilities such as: enrichment and fuel manufacturing plants; nuclear power plants; other reactors such as research reactors and critical assemblies; spent fuel reprocessing plants; and facilities for radioactive waste management, such as treatment, storage and disposal facilities. This Safety Guide also covers issues relating to the decommissioning of nuclear facilities, the closure of waste disposal facilities and site rehabilitation. Section 2 sets out the objectives of regulatory inspection and enforcement. Section 3 covers the management of regulatory inspections. Section 4 covers the performance of regulatory inspections, including internal guidance, planning and preparation, methods of inspection and reports of inspections. Section 5 deals with regulatory enforcement actions. Section 6 covers the assessment of regulatory inspections and enforcement activities. The Appendix provides further details on inspection areas for nuclear facilities

Data Quality Objectives for Regulatory Requirements for Hazardous and Radioactive Air Emissions Sampling and Analysis

Energy Technology Data Exchange (ETDEWEB)

MULKEY, C.H.

1999-07-06

This document describes the results of the data quality objective (DQO) process undertaken to define data needs for state and federal requirements associated with toxic, hazardous, and/or radiological air emissions under the jurisdiction of the River Protection Project (RPP). Hereafter, this document is referred to as the Air DQO. The primary drivers for characterization under this DQO are the regulatory requirements pursuant to Washington State regulations, that may require sampling and analysis. The federal regulations concerning air emissions are incorporated into the Washington State regulations. Data needs exist for nonradioactive and radioactive waste constituents and characteristics as identified through the DQO process described in this document. The purpose is to identify current data needs for complying with regulatory drivers for the measurement of air emissions from RPP facilities in support of air permitting. These drivers include best management practices; similar analyses may have more than one regulatory driver. This document should not be used for determining overall compliance with regulations because the regulations are in constant change, and this document may not reflect the latest regulatory requirements. Regulatory requirements are also expected to change as various permits are issued. Data needs require samples for both radionuclides and nonradionuclide analytes of air emissions from tanks and stored waste containers. The collection of data is to support environmental permitting and compliance, not for health and safety issues. This document does not address health or safety regulations or requirements (those of the Occupational Safety and Health Administration or the National Institute of Occupational Safety and Health) or continuous emission monitoring systems. This DQO is applicable to all equipment, facilities, and operations under the jurisdiction of RPP that emit or have the potential to emit regulated air pollutants.

Data Quality Objectives for Regulatory Requirements for Hazardous and Radioactive Air Emissions Sampling and Analysis

International Nuclear Information System (INIS)

MULKEY, C.H.

1999-01-01

This document describes the results of the data quality objective (DQO) process undertaken to define data needs for state and federal requirements associated with toxic, hazardous, and/or radiological air emissions under the jurisdiction of the River Protection Project (RPP). Hereafter, this document is referred to as the Air DQO. The primary drivers for characterization under this DQO are the regulatory requirements pursuant to Washington State regulations, that may require sampling and analysis. The federal regulations concerning air emissions are incorporated into the Washington State regulations. Data needs exist for nonradioactive and radioactive waste constituents and characteristics as identified through the DQO process described in this document. The purpose is to identify current data needs for complying with regulatory drivers for the measurement of air emissions from RPP facilities in support of air permitting. These drivers include best management practices; similar analyses may have more than one regulatory driver. This document should not be used for determining overall compliance with regulations because the regulations are in constant change, and this document may not reflect the latest regulatory requirements. Regulatory requirements are also expected to change as various permits are issued. Data needs require samples for both radionuclides and nonradionuclide analytes of air emissions from tanks and stored waste containers. The collection of data is to support environmental permitting and compliance, not for health and safety issues. This document does not address health or safety regulations or requirements (those of the Occupational Safety and Health Administration or the National Institute of Occupational Safety and Health) or continuous emission monitoring systems. This DQO is applicable to all equipment, facilities, and operations under the jurisdiction of RPP that emit or have the potential to emit regulated air pollutants

Hiding the tobacco power wall reduces cigarette smoking risk in adolescents: using an experimental convenience store to assess tobacco regulatory options at retail point-of-sale.

Science.gov (United States)

Shadel, William G; Martino, Steven C; Setodji, Claude M; Scharf, Deborah M; Kusuke, Daniela; Sicker, Angela; Gong, Min

2015-11-23

This experiment tested whether changing the location or visibility of the tobacco power wall in a life sized replica of a convenience store had any effect on adolescents' susceptibility to future cigarette smoking. The study was conducted in the RAND StoreLab (RSL), a life sized replica of a convenience store that was developed to experimentally evaluate how changing aspects of tobacco advertising displays in retail point-of-sale environments influences tobacco use risk and behaviour. A randomised, between-subjects experimental design with three conditions that varied the location or visibility of the tobacco power wall within the RSL was used. The conditions were: cashier (the tobacco power wall was located in its typical position behind the cash register counter); sidewall (the tobacco power wall was located on a sidewall away from the cash register); or hidden (the tobacco power wall was located behind the cashier but was hidden behind an opaque wall). The sample included 241 adolescents. Hiding the tobacco power wall significantly reduced adolescents' susceptibility to future cigarette smoking compared to leaving it exposed (ie, the cashier condition; p=0.02). Locating the tobacco power wall on a sidewall away from the cashier had no effect on future cigarette smoking susceptibility compared to the cashier condition (p=0.80). Hiding the tobacco power wall at retail point-of-sale locations is a strong regulatory option for reducing the impact of the retail environment on cigarette smoking risk in adolescents. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/

Data Quality Objectives for Regulatory Requirements for Dangerous Waste Sampling and Analysis; FINAL

International Nuclear Information System (INIS)

MULKEY, C.H.

1999-01-01

This document describes sampling and analytical requirements needed to meet state and federal regulations for dangerous waste (DW). The River Protection Project (RPP) is assigned to the task of storage and interim treatment of hazardous waste. Any final treatment or disposal operations, as well as requirements under the land disposal restrictions (LDRs), fall in the jurisdiction of another Hanford organization and are not part of this scope. The requirements for this Data Quality Objective (DQO) Process were developed using the RPP Data Quality Objective Procedure (Banning 1996), which is based on the U.S. Environmental Protection Agency's (EPA) Guidance for the Data Quality Objectives Process (EPA 1994). Hereafter, this document is referred to as the DW DQO. Federal and state laws and regulations pertaining to waste contain requirements that are dependent upon the composition of the waste stream. These regulatory drivers require that pertinent information be obtained. For many requirements, documented process knowledge of a waste composition can be used instead of analytical data to characterize or designate a waste. When process knowledge alone is used to characterize a waste, it is a best management practice to validate the information with analytical measurements

On-Off Switches for Secondary Cell Wall Biosynthesis

Institute of Scientific and Technical Information of China (English)

Huan-Zhong Wang; Richard A.Dixon

2012-01-01

Secondary cell walls provide plants with rigidity and strength to support their body weight and ensure water and nutrient transport.They also provide textiles,timber,and potentially second-generation biofuels for human use.Genes responsible for synthesis of the different cell wall components,namely cellulose,hemicelluloses,and lignin,are coordinately expressed and under transcriptional regulation.In the past several years,cell wall-related NAC and MYB transcription factors have been intensively investigated in different species and shown to be master switches of secondary cell wall biosynthesis.Positive and negative regulators,which function upstream of NAC master switches,have also been identified in different plant tissues.Further elucidation of the regulatory mechanisms of cell wall synthesis will facilitate the engineering of plant feedstocks suitable for biofuel production.

Data Quality Objectives for Regulatory Requirements for Hazardous and Radioactive Air Emissions Sampling and Analysis; FINAL

International Nuclear Information System (INIS)

MULKEY, C.H.

1999-01-01

This document describes the results of the data quality objective (DQO) process undertaken to define data needs for state and federal requirements associated with toxic, hazardous, and/or radiological air emissions under the jurisdiction of the River Protection Project (RPP). Hereafter, this document is referred to as the Air DQO. The primary drivers for characterization under this DQO are the regulatory requirements pursuant to Washington State regulations, that may require sampling and analysis. The federal regulations concerning air emissions are incorporated into the Washington State regulations. Data needs exist for nonradioactive and radioactive waste constituents and characteristics as identified through the DQO process described in this document. The purpose is to identify current data needs for complying with regulatory drivers for the measurement of air emissions from RPP facilities in support of air permitting. These drivers include best management practices; similar analyses may have more than one regulatory driver. This document should not be used for determining overall compliance with regulations because the regulations are in constant change, and this document may not reflect the latest regulatory requirements. Regulatory requirements are also expected to change as various permits are issued. Data needs require samples for both radionuclides and nonradionuclide analytes of air emissions from tanks and stored waste containers. The collection of data is to support environmental permitting and compliance, not for health and safety issues. This document does not address health or safety regulations or requirements (those of the Occupational Safety and Health Administration or the National Institute of Occupational Safety and Health) or continuous emission monitoring systems. This DQO is applicable to all equipment, facilities, and operations under the jurisdiction of RPP that emit or have the potential to emit regulated air pollutants

[Regulatory radiation risks' for the population and natural objects within the Semipalatinsk Test Site].

Science.gov (United States)

Spiridonov, S I; Teten'kin, V L; Mukusheva, M K; Solomatin, V M

2008-01-01

Advisability of using risks as indicators for estimating radiation impacts on environmental objects and humans has been jusified. Results are presented from identification of dose burdens distribution to various cohorts of the population living within the Semipalatinsk Test Site (STS) and consuming contaminated farm products. Parameters of dose burden distributions are estimated for areas of livestock grazing and the most contaminated sectors within these areas. Dose distributions to meadow plants for the above areas have been found. Regulatory radiation risks for the STS population and meadow ecosystem components have been calculated. Based on the parameters estimated, levels of radiation exposure of the population and herbaceous plants have been compared.

Simulation of condensation and liquid break-up on a micro-object with upper and lower movable walls using Lattice Boltzmann Method

Science.gov (United States)

Asadollahi, Arash; Esmaeeli, Asghar

2018-05-01

In this paper, two-dimensional condensation, liquid behavior on the micro-object with moving walls, and breaking up have been investigated by the Shan and Chen multiphase Lattice Boltzmann Method (LBM), which has the ability to incorporate interactions such as fluid-fluid, and also fluid-solid. Four test cases with low, medium, high, and very high Weber numbers are investigated considering the velocity control of walls in detail. Vertical spread fraction n / h (where n is the minimum liquid thickness after deformation and h is the maximum length of liquid deformation in each time) decreases quickly indicating the liquid tendency to breakup in all cases. Except for the case of a very high Weber number, the separation will not happen and finally after fluctuation the fixed bulk of condensed liquid will be placed on the side of the micro-object. The maximum value of reaction parameter h / d becomes larger as the Weber number increases. It is shown that an increase in the Weber number leads to liquid breakup and this mechanism provides an effective way for removing the condensed liquid from micro-devices surfaces. The results by LBM reveal the liquid evolutionary behavior and breaking up over time and show that it is a controllable situation by manipulating the walls velocity. Moreover, it can be used in order to centralize and aggregate all the liquid to a specific direction.

Prevention as a main objective in the regulatory practices relating to research reactors

International Nuclear Information System (INIS)

Waldman, Ricardo M.

2006-01-01

In Argentina the use of research reactors and critical facilities are very diverse, varying since the production of radionuclides, to the investigation or the teaching. Also diverse are the licensing characteristics, going from the National Atomic Energy Commission-Argentina to national universities. The strategy utilized for the regulatory control is based especially in the prevention. The prevention covers: regulatory framework, to emit standards and regulatory guides, to licensing installations and the personnel. (author) [es

Development of guidance on applications of regulatory requirements for low specific activity materials and surface contaminated objects

International Nuclear Information System (INIS)

Pope, R.B.; Easton, E.P.; Shankman, S.F.

1997-01-01

In 1985, the International Atomic Energy Agency issued revised regulations for the safe transport of radioactive material. Significant among the changes were major revisions to requirements for Low Specific Activity (LSA) material and Surface Contaminated Objects (SCOs). In preparation for the adoption of these requirements into regulations in the United States, it became apparent that guidance on how to apply these requirements, clarifying technical uncertainties and ensuring proper implementation, would be needed both by the regulators and those regulated. Thus, the US Department of Transportation and the US Nuclear Regulatory Commission, with the assistance of staff from Oak Ridge National Laboratory, are preparing regulatory guidance for LSA material and SCO transport. The guidance will present examples of acceptable methods for demonstrating compliance with the revised rules. Ideas being investigated for inclusion in the pending guidance are discussed in this paper. Under current plans, the guidance will be issued for public comment prior to final issuance of the guidance in 1997

Development of guidance on applications of regulatory requirements for low specific activity materials and surface contaminated objects

International Nuclear Information System (INIS)

Pope, R.B.; Easton, E.P.; Shankman, S.F.; Boyle, R.W.

1997-01-01

In 1985, the International Atomic Energy Agency issued revised regulations for the safe transport of radioactive material. Significant among the changes were major revisions to requirements for Low Specific Activity (LSA) material and Surface Contaminated Objects (SCOs). In preparation for the adoption of these requirements into regulations in the United States, it became apparent that guidance on how to apply these requirements, clarifying technical uncertainties and ensuring proper implementation, would be needed both by the regulators and those regulated. Thus, the US Department of Transportation and the U.S. Nuclear Regulatory Commission, with the assistance of staff from Oak Ridge National Laboratory, are preparing regulatory guidance for LSA material and SCO transport. The guidance will present examples of acceptable methods for demonstrating compliance with the revised rules. Ideas being investigated for inclusion in the pending guidance are discussed in this paper. Under current plans, the guidance will be issued for public comment prior to final issue of the guidance in 1997. (Author)

Nuclear regulatory decision making

International Nuclear Information System (INIS)

2005-01-01

The fundamental objective of all nuclear safety regulatory bodies is to ensure that nuclear utilities operate their plants at all times in an acceptably safe manner. In meeting this objective, the regulatory body should strive to ensure that its regulatory decisions are technically sound, consistent from case to case, and timely. In addition, the regulator must be aware that its decisions and the circumstances surrounding those decisions can affect how its stakeholders, such as government policy makers, the industry it regulates, and the public, view it as an effective and credible regulator. In order to maintain the confidence of those stakeholders, the regulator should make sure that its decisions are transparent, have a clear basis in law and regulations, and are seen by impartial observers to be fair to all parties. Based on the work of a Nuclear Energy Agency (NEA) expert group, this report discusses some of the basic principles and criteria that a regulatory body should consider in making decisions and describes the elements of an integrated framework for regulatory decision making. (author)

Assessment of regulatory effectiveness. Peer discussions on regulatory practices

International Nuclear Information System (INIS)

1999-09-01

This report arises from the seventh series of peer discussions on regulatory practices entitled 'Assessment of Regulatory Effectiveness'. The term 'regulatory effectiveness' covers the quality of the work and level of performance of a regulatory body. In this sense, regulatory effectiveness applies to regulatory body activities aimed at preventing safety degradation and ensuring that an acceptable level of safety is being maintained by the regulated operating organizations. In addition, regulatory effectiveness encompasses the promotion of safety improvements, the timely and cost effective performance of regulatory functions in a manner which ensures the confidence of the operating organizations, the general public and the government, and striving for continuous improvements to performance. Senior regulators from 22 Member States participated in two peer group discussions during March and May 1999. The discussions were focused on the elements of an effective regulatory body, possible indicators of regulatory effectiveness and its assessment. This report presents the outcome of these meetings and recommendations of good practices identified by senior regulators, which do not necessarily reflect those of the governments of the nominating Member States, the organizations they belong to, or the International Atomic Energy Agency. In order to protect people and the environment from hazards associated with nuclear facilities, the main objective of a nuclear regulatory body is to ensure that a high level of safety in the nuclear activities under its jurisdiction is achieved, maintained and within the control of operating organizations. Even if it is possible to directly judge objective safety levels at nuclear facilities, such safety levels would not provide an exclusive indicator of regulatory effectiveness. The way the regulatory body ensures the safety of workers and the public and the way it discharges its responsibilities also determine its effectiveness. Hence the

Bacillus subtilis as a platform for molecular characterisation of regulatory mechanisms of Enterococcus faecalis resistance against cell wall antibiotics.

Science.gov (United States)

Fang, Chong; Stiegeler, Emanuel; Cook, Gregory M; Mascher, Thorsten; Gebhard, Susanne

2014-01-01

To combat antibiotic resistance of Enterococcus faecalis, a better understanding of the molecular mechanisms, particularly of antibiotic detection, signal transduction and gene regulation is needed. Because molecular studies in this bacterium can be challenging, we aimed at exploiting the genetically highly tractable Gram-positive model organism Bacillus subtilis as a heterologous host. Two fundamentally different regulators of E. faecalis resistance against cell wall antibiotics, the bacitracin sensor BcrR and the vancomycin-sensing two-component system VanSB-VanRB, were produced in B. subtilis and their functions were monitored using target promoters fused to reporter genes (lacZ and luxABCDE). The bacitracin resistance system BcrR-BcrAB of E. faecalis was fully functional in B. subtilis, both regarding regulation of bcrAB expression and resistance mediated by the transporter BcrAB. Removal of intrinsic bacitracin resistance of B. subtilis increased the sensitivity of the system. The lacZ and luxABCDE reporters were found to both offer sensitive detection of promoter induction on solid media, which is useful for screening of large mutant libraries. The VanSB-VanRB system displayed a gradual dose-response behaviour to vancomycin, but only when produced at low levels in the cell. Taken together, our data show that B. subtilis is a well-suited host for the molecular characterization of regulatory systems controlling resistance against cell wall active compounds in E. faecalis. Importantly, B. subtilis facilitates the careful adjustment of expression levels and genetic background required for full functionality of the introduced regulators.

Finite element analyses for seismic shear wall international standard problem

International Nuclear Information System (INIS)

Park, Y.J.; Hofmayer, C.H.

1998-04-01

Two identical reinforced concrete (RC) shear walls, which consist of web, flanges and massive top and bottom slabs, were tested up to ultimate failure under earthquake motions at the Nuclear Power Engineering Corporation's (NUPEC) Tadotsu Engineering Laboratory, Japan. NUPEC provided the dynamic test results to the OECD (Organization for Economic Cooperation and Development), Nuclear Energy Agency (NEA) for use as an International Standard Problem (ISP). The shear walls were intended to be part of a typical reactor building. One of the major objectives of the Seismic Shear Wall ISP (SSWISP) was to evaluate various seismic analysis methods for concrete structures used for design and seismic margin assessment. It also offered a unique opportunity to assess the state-of-the-art in nonlinear dynamic analysis of reinforced concrete shear wall structures under severe earthquake loadings. As a participant of the SSWISP workshops, Brookhaven National Laboratory (BNL) performed finite element analyses under the sponsorship of the U.S. Nuclear Regulatory Commission (USNRC). Three types of analysis were performed, i.e., monotonic static (push-over), cyclic static and dynamic analyses. Additional monotonic static analyses were performed by two consultants, F. Vecchio of the University of Toronto (UT) and F. Filippou of the University of California at Berkeley (UCB). The analysis results by BNL and the consultants were presented during the second workshop in Yokohama, Japan in 1996. A total of 55 analyses were presented during the workshop by 30 participants from 11 different countries. The major findings on the presented analysis methods, as well as engineering insights regarding the applicability and reliability of the FEM codes are described in detail in this report. 16 refs., 60 figs., 16 tabs

Dissecting the regulation of pollen tube growth by modelling the interplay of hydrodynamics, cell wall and ion dynamics

Directory of Open Access Journals (Sweden)

Junli eLiu

2014-08-01

Full Text Available Hydrodynamics, cell wall and ion dynamics are all important properties that regulate pollen tube growth. Currently, the two main pollen tube growth models, the cell wall model and the hydrodynamic model do not appear to be reconcilable. Here we develop an integrative model for pollen tube growth and show that our model reproduces key experimental observations: 1 that the hypertonic condition leads to a much longer oscillatory period and that the hypotonic condition halves the oscillatory period; 2 that oscillations in turgor are experimentally undetectable; 3 that increasing the extracellular calcium concentration or decreasing the pH decreases the growth oscillatory amplitude; 4 that knockout of Raba4d, a member of the Rab family of small GTPase proteins, decreases pollen tube length after germination for 24 hours. Using the model generated here, we reveal that 1 when cell wall extensibility is large, pollen tube may sustain growth at different volume changes and maintain relatively stable turgor; 2 turgor increases if cell wall extensibility decreases; 3 increasing turgor due to decrease in osmolarity in the media, although very small, increases volume change . However, increasing turgor due to decrease in cell wall extensibility decreases volume change. In this way regulation of pollen tube growth by turgor is context dependent. By changing the osmolarity in the media, the main regulatory points are extracellular osmolarity for water flow and turgor for the volume encompassed by the cell wall. However, if the viscosity of cell wall changes, the main regulatory points are turgor for water flow and wall extensibility for the volume encompassed by the cell wall. The novel methodology developed here reveals the underlying context-dependent regulatory principle of pollen tube growth.

Methodology For Evaluation Of Regulatory Effectiveness In Physical Protection

International Nuclear Information System (INIS)

Izmaylov, Alexander; Valente, John; Griggs, James R.; Rexroth, Paul; Piskarev, Alexander; Babkin, Vladimir; Sokolov, Egor; Melton, Ronald B.; Cunningham, Mitchel E.; Baker, Kathryn A.; Brothers, Alan J.

2005-01-01

Material protection, control, and accounting (MPC and A) regulatory documents play an important role in securing and protecting nuclear material by regulating a variety of activities at different hierarchical levels. The development, implementation, and practical application of these regulatory documents requires a significant investment of financial and material resources. Therefore, it is important to evaluate the effectiveness of the regulatory development process and the extent to which regulations improve the effectiveness of MPC and A at nuclear sites. The joint Russian and U.S. Regulatory Development Project has a goal of evaluating the effectiveness of regulatory documents developed for MPC and A. As part of this joint Project, a methodology for evaluating effectiveness has been developed. This methodology was developed around physical protection objectives. The developed methodology specifies physical protection objectives to be accomplished through the implementation of a regulatory system based on the physical protection goals at the nuclear sites. It includes approaches to assessing regulatory effectiveness, the hierarchical structure of physical protection objectives to be accomplished through implementing regulations, a 'mapping' of the physical protection objectives to the regulatory framework, a list of criteria for evaluating the effectiveness of physical protection regulations and effectiveness indicators, as well as means and methods for gathering information and implementation of this evaluation.

KWOC [Key-Word-Out-of-Context] Index of US Nuclear Regulatory Commission Regulatory Guide Series

International Nuclear Information System (INIS)

Jennings, S.D.

1990-04-01

To meet the objectives of the program funded by the Department of Energy (DOE)-Nuclear Energy (NE) Technology Support Programs, the Performance Assurance Project Office (PAPO) administers a Performance Assurance Information Program that collects, compiles, and distributes program-related information, reports, and publications for the benefit of the DOE-NE program participants. THE ''KWOC Index of US Nuclear Regulatory Commission Regulatory Guide Series'' is prepared as an aid in searching for specific topics in the US Nuclear Regulatory Commission, Regulatory Guide Series

Histochemical effects of γ radiation on soft fruit cell walls

International Nuclear Information System (INIS)

Foa, E.; Jona, R.; Vallania, R.

1980-01-01

Irradiation effects in peaches, tomatoes, cherries and grapes on the composition of cell wall polysaccharides were investigated by histochemical techniques. Cell wall polysaccharides, separated by a modified Jensen's method were pectins, hemicellulose, non-cellulosic polysaccharides and cellulose. The extinction values of Periodic Acid Schiff stained tissues was measured by microscopical photometry. Irradiation induced highly significant changes in polysaccharide composition of mesocarp cell walls; these changes were found to be a function of time of irradiation after harvest and of the species tested. A general influence on polysaccharide molecules was not found. Variations produced by irradiation are postulated to be an interference with a regulatory system rather than a breakdown of a functional molecule (metabolic enzyme or polysaccharide. (author)

The Political Economy of Regulatory Risk

OpenAIRE

Strausz, Roland

2009-01-01

I investigate the argument that, in a two–party system with different regulatory objectives, political uncertainty generates regulatory risk. I show that this risk has a fluctuation effect that hurts both parties and an output–expansion effect that benefits one party. Consequently, at least one party dislikes regulatory risk. Moreover, both political parties gain from eliminating regulatory risk when political divergence is small or the winning probability of the regulatory–risk–averse party ...

Risk-based Regulatory Evaluation Program methodology

International Nuclear Information System (INIS)

DuCharme, A.R.; Sanders, G.A.; Carlson, D.D.; Asselin, S.V.

1987-01-01

The objectives of this DOE-supported Regulatory Evaluation Progrwam are to analyze and evaluate the safety importance and economic significance of existing regulatory guidance in order to assist in the improvement of the regulatory process for current generation and future design reactors. A risk-based cost-benefit methodology was developed to evaluate the safety benefit and cost of specific regulations or Standard Review Plan sections. Risk-based methods can be used in lieu of or in combination with deterministic methods in developing regulatory requirements and reaching regulatory decisions

Towards medicines regulatory authorities' quality performance improvement: value for public health.

Science.gov (United States)

Pejović, Gordana; Filipović, Jovan; Tasić, Ljiljana; Marinković, Valentina

2016-01-01

The purpose of this article is to explore the possibility of implementing total quality management (TQM) principles in national medicines regulatory authorities in Europe to achieve all public health objectives. Bearing in mind that medicines regulation is a governmental function that serves societal objectives to protect and promote public health, measuring the effective achievement of quality objectives related to public health is of utmost importance. A generic TQM model for meeting public health objectives was developed and was tested on 10 European national medicines regulatory authorities with different regulatory performances. Participating national medicines regulatory authorities recognised all TQM factors of the proposed model in implemented systems with different degrees of understanding. An analysis of responses was performed within the framework of two established criteria-the regulatory authority's category and size. The value of the paper is twofold. First, the new generic TQM model proposes to integrate four public health objectives with six TQM factors. Second, national medicines regulatory authorities were analysed as public organisations and health authorities to develop a proper tool for assessing their regulatory performance. The paper emphasises the importance of designing an adequate approach to performance measurement of quality management systems in medicines regulatory authorities that will support their public service missions. Copyright © 2014 John Wiley & Sons, Ltd.

Team structure and regulatory focus: the impact of regulatory fit on team dynamic.

Science.gov (United States)

Dimotakis, Nikolaos; Davison, Robert B; Hollenbeck, John R

2012-03-01

We report a within-teams experiment testing the effects of fit between team structure and regulatory task demands on task performance and satisfaction through average team member positive affect and helping behaviors. We used a completely crossed repeated-observations design in which 21 teams enacted 2 tasks with different regulatory focus characteristics (prevention and promotion) in 2 organizational structures (functional and divisional), resulting in 84 observations. Results suggested that salient regulatory demands inherent in the task interacted with structure to determine objective and subjective team-level outcomes, such that functional structures were best suited to (i.e., had best fit with) tasks with a prevention regulatory focus and divisional structures were best suited to tasks with a promotion regulatory focus. This contingency finding integrates regulatory focus and structural contingency theories, and extends them to the team level with implications for models of performance, satisfaction, and team dynamics.

INTEGRATED ENERGY EFFICIENT WINDOW-WALL SYSTEMS

Energy Technology Data Exchange (ETDEWEB)

Michael Arney, Ph.D.

2002-12-31

The building industry faces the challenge of reducing energy use while simultaneously improving construction methods and marketability. This paper describes the first phase of a project to address these concerns by designing an Integrated Window Wall System (IWWS) that can be commercialized. This work builds on previous research conducted during the 1990's by Lawrence Berkeley national Laboratories (LBNL). During this phase, the objective was to identify appropriate technologies, problems and issues and develop a number of design concepts. Four design concepts were developed into prototypes and preliminary energy analyses were conducted Three of these concepts (the foam wall, steel wall, and stiffened plate designs) showed particular potential for meeting the project objectives and will be continued into a second phase where one or two of the systems will be brought closer to commercialization.

Identification of lignin genes and regulatory sequences involved in secondary cell wall formation in Acacia auriculiformis and Acacia mangium via de novo transcriptome sequencing

Directory of Open Access Journals (Sweden)

Cannon Charles H

2011-07-01

Full Text Available Abstract Background Acacia auriculiformis × Acacia mangium hybrids are commercially important trees for the timber and pulp industry in Southeast Asia. Increasing pulp yield while reducing pulping costs are major objectives of tree breeding programs. The general monolignol biosynthesis and secondary cell wall formation pathways are well-characterized but genes in these pathways are poorly characterized in Acacia hybrids. RNA-seq on short-read platforms is a rapid approach for obtaining comprehensive transcriptomic data and to discover informative sequence variants. Results We sequenced transcriptomes of A. auriculiformis and A. mangium from non-normalized cDNA libraries synthesized from pooled young stem and inner bark tissues using paired-end libraries and a single lane of an Illumina GAII machine. De novo assembly produced a total of 42,217 and 35,759 contigs with an average length of 496 bp and 498 bp for A. auriculiformis and A. mangium respectively. The assemblies of A. auriculiformis and A. mangium had a total length of 21,022,649 bp and 17,838,260 bp, respectively, with the largest contig 15,262 bp long. We detected all ten monolignol biosynthetic genes using Blastx and further analysis revealed 18 lignin isoforms for each species. We also identified five contigs homologous to R2R3-MYB proteins in other plant species that are involved in transcriptional regulation of secondary cell wall formation and lignin deposition. We searched the contigs against public microRNA database and predicted the stem-loop structures of six highly conserved microRNA families (miR319, miR396, miR160, miR172, miR162 and miR168 and one legume-specific family (miR2086. Three microRNA target genes were predicted to be involved in wood formation and flavonoid biosynthesis. By using the assemblies as a reference, we discovered 16,648 and 9,335 high quality putative Single Nucleotide Polymorphisms (SNPs in the transcriptomes of A. auriculiformis and A. mangium

Transcriptional regulatory programs underlying barley germination and regulatory functions of Gibberellin and abscisic acid

Science.gov (United States)

2011-01-01

Background Seed germination is a complex multi-stage developmental process, and mainly accomplished through concerted activities of many gene products and biological pathways that are often subjected to strict developmental regulation. Gibberellins (GA) and abscisic acid (ABA) are two key phytohormones regulating seed germination and seedling growth. However, transcriptional regulatory networks underlying seed germination and its associated biological pathways are largely unknown. Results The studies examined transcriptomes of barley representing six distinct and well characterized germination stages and revealed that the transcriptional regulatory program underlying barley germination was composed of early, late, and post-germination phases. Each phase was accompanied with transcriptional up-regulation of distinct biological pathways. Cell wall synthesis and regulatory components including transcription factors, signaling and post-translational modification components were specifically and transiently up-regulated in early germination phase while histone families and many metabolic pathways were up-regulated in late germination phase. Photosynthesis and seed reserve mobilization pathways were up-regulated in post-germination phase. However, stress related pathways and seed storage proteins were suppressed through the entire course of germination. A set of genes were transiently up-regulated within three hours of imbibition, and might play roles in initiating biological pathways involved in seed germination. However, highly abundant transcripts in dry barley and Arabidopsis seeds were significantly conserved. Comparison with transcriptomes of barley aleurone in response to GA and ABA identified three sets of germination responsive genes that were regulated coordinately by GA, antagonistically by ABA, and coordinately by GA but antagonistically by ABA. Major CHO metabolism, cell wall degradation and protein degradation pathways were up-regulated by both GA and seed

Transcriptional regulatory programs underlying barley germination and regulatory functions of Gibberellin and abscisic acid

Directory of Open Access Journals (Sweden)

Lin Li

2011-06-01

Full Text Available Abstract Background Seed germination is a complex multi-stage developmental process, and mainly accomplished through concerted activities of many gene products and biological pathways that are often subjected to strict developmental regulation. Gibberellins (GA and abscisic acid (ABA are two key phytohormones regulating seed germination and seedling growth. However, transcriptional regulatory networks underlying seed germination and its associated biological pathways are largely unknown. Results The studies examined transcriptomes of barley representing six distinct and well characterized germination stages and revealed that the transcriptional regulatory program underlying barley germination was composed of early, late, and post-germination phases. Each phase was accompanied with transcriptional up-regulation of distinct biological pathways. Cell wall synthesis and regulatory components including transcription factors, signaling and post-translational modification components were specifically and transiently up-regulated in early germination phase while histone families and many metabolic pathways were up-regulated in late germination phase. Photosynthesis and seed reserve mobilization pathways were up-regulated in post-germination phase. However, stress related pathways and seed storage proteins were suppressed through the entire course of germination. A set of genes were transiently up-regulated within three hours of imbibition, and might play roles in initiating biological pathways involved in seed germination. However, highly abundant transcripts in dry barley and Arabidopsis seeds were significantly conserved. Comparison with transcriptomes of barley aleurone in response to GA and ABA identified three sets of germination responsive genes that were regulated coordinately by GA, antagonistically by ABA, and coordinately by GA but antagonistically by ABA. Major CHO metabolism, cell wall degradation and protein degradation pathways were up

Shielding wall for thermonuclear device

International Nuclear Information System (INIS)

Uchida, Takaho.

1989-01-01

This invention concerns shielding walls opposing to plasmas of a thermonuclear device and it is an object thereof to conduct reactor operation with no troubles even if a portion of shielding wall tiles should be damaged. That is, the shielding wall tiles are constituted as a dual layer structure in which the lower base tiles are connected by means of bolts to first walls. Further, the upper surface tiles are bolt-connected to the layer base tiles. In this structure, the plasma thermal loads are directly received by the surface layer tiles and heat is conducted by means of conduction and radiation to the underlying base tiles and the first walls. Even upon occurrence of destruction accidents to the surface layer tiles caused by incident heat or electromagnetic force upon elimination of plasmas, since the underlying base tiles remain as they are, the first walls constituted with stainless steels, etc. are not directly exposed to the plasmas. Accordingly, the integrity of the first walls having cooling channels can be maintained and sputtering intrusion of atoms of high atom number into the plasmas can be prevented. (I.S.)

Topological domain walls in helimagnets

Science.gov (United States)

Schoenherr, P.; Müller, J.; Köhler, L.; Rosch, A.; Kanazawa, N.; Tokura, Y.; Garst, M.; Meier, D.

2018-05-01

Domain walls naturally arise whenever a symmetry is spontaneously broken. They interconnect regions with different realizations of the broken symmetry, promoting structure formation from cosmological length scales to the atomic level1,2. In ferroelectric and ferromagnetic materials, domain walls with unique functionalities emerge, holding great promise for nanoelectronics and spintronics applications3-5. These walls are usually of Ising, Bloch or Néel type and separate homogeneously ordered domains. Here we demonstrate that a wide variety of new domain walls occurs in the presence of spatially modulated domain states. Using magnetic force microscopy and micromagnetic simulations, we show three fundamental classes of domain walls to arise in the near-room-temperature helimagnet iron germanium. In contrast to conventional ferroics, the domain walls exhibit a well-defined inner structure, which—analogous to cholesteric liquid crystals—consists of topological disclination and dislocation defects. Similar to the magnetic skyrmions that form in the same material6,7, the domain walls can carry a finite topological charge, permitting an efficient coupling to spin currents and contributions to a topological Hall effect. Our study establishes a new family of magnetic nano-objects with non-trivial topology, opening the door to innovative device concepts based on helimagnetic domain walls.

Regulatory guidance document

International Nuclear Information System (INIS)

1994-05-01

The Office of Civilian Radioactive Waste Management (OCRWM) Program Management System Manual requires preparation of the OCRWM Regulatory Guidance Document (RGD) that addresses licensing, environmental compliance, and safety and health compliance. The document provides: regulatory compliance policy; guidance to OCRWM organizational elements to ensure a consistent approach when complying with regulatory requirements; strategies to achieve policy objectives; organizational responsibilities for regulatory compliance; guidance with regard to Program compliance oversight; and guidance on the contents of a project-level Regulatory Compliance Plan. The scope of the RGD includes site suitability evaluation, licensing, environmental compliance, and safety and health compliance, in accordance with the direction provided by Section 4.6.3 of the PMS Manual. Site suitability evaluation and regulatory compliance during site characterization are significant activities, particularly with regard to the YW MSA. OCRWM's evaluation of whether the Yucca Mountain site is suitable for repository development must precede its submittal of a license application to the Nuclear Regulatory Commission (NRC). Accordingly, site suitability evaluation is discussed in Chapter 4, and the general statements of policy regarding site suitability evaluation are discussed in Section 2.1. Although much of the data and analyses may initially be similar, the licensing process is discussed separately in Chapter 5. Environmental compliance is discussed in Chapter 6. Safety and Health compliance is discussed in Chapter 7

Computer simulations of a generic truck cask in a regulatory fire using the Container Analysis Fire Environment (CAFE) code

International Nuclear Information System (INIS)

Ju, H.; Greiner, M.; Suo-Anttila, A.

2002-01-01

The Container Analysis Fire Environment (CAFE) computer code is designed to predict accurately convection and radiation heat transfer to a thermally massive object engulfed in a large pool fire. It is well suited for design and risk analyses of spent nuclear fuel transport systems. CAFE employs computational fluid dynamics and several fire and radiation models. These models must be benchmarked using experimental results. In this paper, a set of wind velocity conditions are determined which allow CAFE accurately to reproduce recent heat transfer measurements for a thick walled calorimeter in a ST-1 regulatory pool fire. CAFE is then used to predict the response of an intack (thin walled) generic legal weight truck cask. The maximum temperatures reached by internal components are within safe limits. A simple 800 deg. C, grey-radiation fire model gives maximum component temperatures that are somewhat below those predicted by CAFE. (author)

The influence of wall stress on AAA growth and biomarkers

NARCIS (Netherlands)

Speelman, L.; Hellenthal, F.A.M.V.I.; Pulinx, B.; Bosboom, E.M.H.; Breeuwer, M.; Sambeek, M.R.; Vosse, van de F.N.; Jacobs, M.J.H.M.; Wodzig, W.K.W.H.; Schurink, G.W.H.

2010-01-01

Objectives This study investigated the relation between abdominal aortic aneurysm (AAA) wall stress, AAA growth rate and biomarker concentrations. With increasing wall stress, more damage may be caused to the AAA wall, possibly leading to progression of the aneurysm and reflection in up- or

Dynamic wall demonstration project

Energy Technology Data Exchange (ETDEWEB)

Nakatsui, L.; Mayhew, W.

1990-12-01

The dynamic wall concept is a ventilation strategy that can be applied to a single family dwelling. With suitable construction, outside air can be admitted through the exterior walls of the house to the interior space to function as ventilation air. The construction and performance monitoring of a demonstration house built to test the dynamic wall concept in Sherwood Park, Alberta, is described. The project had the objectives of demonstrating and assessing the construction methods; determining the cost-effectiveness of the concept in Alberta; analyzing the operation of the dynamic wall system; and determining how other components and systems in the house interact with the dynamic wall. The exterior wall construction consisted of vinyl siding, spun-bonded polyolefin-backed (SBPO) rigid fiberglass sheathing, 38 mm by 89 mm framing, fiberglass batt insulation and 12.7 mm drywall. The mechanical system was designed to operate in the dynamic (negative pressure) mode, however flexibility was provided to allow operation in the static (balanced pressure) mode to permit monitoring of the walls as if they were in a conventional house. The house was monitored by an extensive computerized monitoring system. Dynamic wall operation was dependent on pressure and temperature differentials between indoor and outdoor as well as wind speed and direction. The degree of heat gain was found to be ca 74% of the indoor-outdoor temperature differential. Temperature of incoming dynamic air was significantly affected by solar radiation and measurement of indoor air pollutants found no significant levels. 4 refs., 34 figs., 11 tabs.

Genome-Wide Association Mapping for Cell Wall Composition and Properties in Temperate Grasses

DEFF Research Database (Denmark)

Bellucci, Andrea

with a wide range of chemical bounds. At present the interest in plant cell wall is growing due to the possibility to convert ligno-cellulosic biomass (e.g. agricultural residues) into bioethanol but also for the benefits to human health of some cell wall constituents found in cereals, in particular beta......-glucans. Plant cell wall biosynthesis is regulated by a large number of genes and regulatory factors but very few of these are known and characterized. This PhD project aimed to the identification of putative candidate genes involved in plant cell wall composition and properties using a genome wide (GWAS......) approach. The species investigate were wheat, barley and B. distachyon, considered a model plant for temperate cereals. Agronomical traits as yield and plant height were also included in the analysis along with cell wall composition and saccharification properties. Several marker-trait associations were...

Reliability-based design of a retaining wall

OpenAIRE

Kim, John Sang

1995-01-01

A retaining wall is subject to various limit states such as sliding, overturning and bearing capacity, and it can fail by anyone of them. Since a great deal of uncertainty is involved in the analysis of the limit states~ the use of detenninistic conventional safety factors may produce a misleading result. The main objective of this study is to develop a procedure for the optimum design of a retaining wall by using the reliability theory. Typical gravity retaining walls with fou...

A film-based wall shear stress sensor for wall-bounded turbulent flows

Science.gov (United States)

Amili, Omid; Soria, Julio

2011-07-01

In wall-bounded turbulent flows, determination of wall shear stress is an important task. The main objective of the present work is to develop a sensor which is capable of measuring surface shear stress over an extended region applicable to wall-bounded turbulent flows. This sensor, as a direct method for measuring wall shear stress, consists of mounting a thin flexible film on the solid surface. The sensor is made of a homogeneous, isotropic, and incompressible material. The geometry and mechanical properties of the film are measured, and particles with the nominal size of 11 μm in diameter are embedded on the film's surface to act as markers. An optical technique is used to measure the film deformation caused by the flow. The film has typically deflection of less than 2% of the material thickness under maximum loading. The sensor sensitivity can be adjusted by changing the thickness of the layer or the shear modulus of the film's material. The paper reports the sensor fabrication, static and dynamic calibration procedure, and its application to a fully developed turbulent channel flow at Reynolds numbers in the range of 90,000-130,000 based on the bulk velocity and channel full height. The results are compared to alternative wall shear stress measurement methods.

Sociotechnical systems as a framework for regulatory system design and evaluation: Using Work Domain Analysis to examine a new regulatory system.

Science.gov (United States)

Carden, Tony; Goode, Natassia; Read, Gemma J M; Salmon, Paul M

2017-03-15

Like most work systems, the domain of adventure activities has seen a series of serious incidents and subsequent calls to improve regulation. Safety regulation systems aim to promote safety and reduce accidents. However, there is scant evidence they have led to improved safety outcomes. In fact there is some evidence that the poor integration of regulatory system components has led to adverse safety outcomes in some contexts. Despite this, there is an absence of methods for evaluating regulatory and compliance systems. This article argues that sociotechnical systems theory and methods provide a suitable framework for evaluating regulatory systems. This is demonstrated through an analysis of a recently introduced set of adventure activity regulations. Work Domain Analysis (WDA) was used to describe the regulatory system in terms of its functional purposes, values and priority measures, purpose-related functions, object-related processes and cognitive objects. This allowed judgement to be made on the nature of the new regulatory system and on the constraints that may impact its efficacy following implementation. Importantly, the analysis suggests that the new system's functional purpose of ensuring safe activities is not fully supported in terms of the functions and objects available to fulfil them. Potential improvements to the design of the system are discussed along with the implications for regulatory system design and evaluation across the safety critical domains generally. Copyright © 2017 Elsevier Ltd. All rights reserved.

Effect of food intake on left ventricular wall stress

OpenAIRE

Gårdinger, Ylva; Hlebowicz, Joanna; Björgell, Ola; Dencker, Magnus

2014-01-01

Objective: Left ventricular wall stress has been investigated in a variety of populations, but the effect of food intake has not been evaluated. We assessed whether left ventricular wall stress is affected by food intake in healthy subjects. Methods: Twenty-three healthy subjects aged 25.6 +/- 4.5 years were investigated. Meridional end-systolic wall stress (ESS) and circumferential end-systolic wall stress (cESS) were measured before, 30 minutes after, and 110 minutes after a standardised me...

Evaluation of masonry wall design at nuclear power plants

International Nuclear Information System (INIS)

Con, V.N.; Subramonian, N.; Chokshi, N.

1983-01-01

The structural integrity of safety-related masonry walls in operating nuclear power plants may not be maintained when subjected to certain loads and load combinations. The paper presents some findings based upon the review of the design and analysis procedures used by the licensees in the reevaluation of safety-related masonry walls. The design criteria developed by the Structural Engineering Branch (SEB) of the United States Nuclear Regulatory Commission (NRC) along with other standard codes such as the Uniform Building Code, ACI 531-79, ATC 3-06, and NCMA were used as guidance in evaluating the design criteria developed by the licensees. The paper deals with the following subject areas: loads and load combinations, allowable stresses, analytical procedures, and modification methods. The paper concludes that, in general, the masonry walls in nuclear power plants comply with the working stress design requirements. In some cases, certain nonlinear analysis methods were used. The applicability of these methods is discussed. (orig.)

Fracture mechanics of thin wall cylindrical pressure vessels: an interim review

International Nuclear Information System (INIS)

Kurtz, R.J.; Olson, N.J.

1977-08-01

The report is a result of activities in the LMFBR Fuel Rod Transient Performance Program sponsored by the LMFBR Branch of the Division of Project Management, U.S. Nuclear Regulatory Commission. One of the objectives is to develop predictions relative to the length, direction, and rate of growth of cladding rips subsequent to (or concurrent with) the initial cladding breach during unprotected transients. To provide a basis for evaluation, Battelle, Pacific Northwest Laboratories has reviewed most available fracture mechanics assessments relative to thin-wall cylindrical pressure vessels. The purpose of the report is to review the various fracture mechanics models and to describe the pertinent fracture parameters. It is intended to provide a formal basis for assessing future analytical predictions of fracture behavior of materials exposed to transient LMFBR thermal and mechanical loading conditions. In addition, the report is expected to provide reference material for evaluating or developing experimental programs required to properly address the problem of predicting fracture behavior of materials during transient events

Quality management of the nuclear regulatory body. Peer discussions on regulatory practices

International Nuclear Information System (INIS)

2001-09-01

This report is the outcome of the ninth series of peer discussions on regulatory practices entitled Nuclear Regulatory Body Quality Management, held in March and May 2001, and which involved the participation of senior nuclear regulators from 23 IAEA Member States. This report conveys the essence of two peer group discussions and highlights some good practices identified by the participating senior regulators. The objective of the discussions was to share experiences of regulatory bodies in implementing QM systems in their own work so as to ensure that the regulatory control over the licensees is effective and efficient and is commensurate with the mandate assigned by their governments. The shared experiences and good practices presented in the report, however, do not necessarily reflect the views of and good practices endorsed by the governments of the nominating Member States, the organizations to which the regulators belong, or the IAEA. The report sets down the peer group's experience in developing, implementing and evaluating QM within their regulatory bodies and identifies points to bear in mind when introducing such a system. This report is structured so that it covers the subject matter under the main headings of: application of quality management to regulatory work; development and implementation of quality management; assessment and improvement of performance; and good practices

Nuclear regulatory decision making

International Nuclear Information System (INIS)

Wieland, Patricia; Almeida, Ivan Pedro Salati de

2011-01-01

The scientific considerations upon which the nuclear regulations are based provide objective criteria for decisions on nuclear safety matters. However, the decisions that a regulatory agency takes go far beyond granting or not an operating license based on assessment of compliance. It may involve decisions about hiring experts or research, appeals, responses to other government agencies, international agreements, etc.. In all cases, top management of the regulatory agency should hear and decide the best balance between the benefits of regulatory action and undue risks and other associated impacts that may arise, including issues of credibility and reputation. The establishment of a decision framework based on well established principles and criteria ensures performance stability and consistency, preventing individual subjectivity. This article analyzes the challenges to the decision-making by regulatory agencies to ensure coherence and consistency in decisions, even in situations where there is uncertainty, lack of reliable information and even divergence of opinions among experts. The article explores the basic elements for a framework for regulatory decision-making. (author)

A review of NRC regulatory processes and functions

International Nuclear Information System (INIS)

1981-05-01

A reexamination by the ACRS of the Regulatory Process has been made. Objectives were to provide in a single source, ACRS' understanding of the Regulatory Process and to point out perceived weaknesses and to make appropriate recommendations for change

Patient-specific AAA wall stress analysis: 99-percentile versus peak stress

NARCIS (Netherlands)

Speelman, L.; Bosboom, E.M.H.; Schurink, G.W.H.; Hellenthal, F.A.M.V.I.; Buth, J.; Breeuwer, M.; Jacobs, M.J.; Vosse, van de F.N.

2008-01-01

Objective Biomechanically, rupture of an Abdominal Aortic Aneurysm (AAA) occurs when the stress acting on the wall due to the blood pressure, exceeds the strength of the wall. Peak wall stress estimations, based on CT reconstruction, may be prone to observer variation. This study focuses on the

Modelling and Order of Acoustic Transfer Functions Due to Reflections from Augmented Objects

Directory of Open Access Journals (Sweden)

Diemer de Vries

2007-01-01

Full Text Available It is commonly accepted that the sound reflections from real physical objects are much more complicated than what usually is and can be modelled by room acoustics modelling software. The main reason for this limitation is the level of detail inherent in the physical object in terms of its geometrical and acoustic properties. In the present paper, the complexity of the sound reflections from a corridor wall is investigated by modelling the corresponding acoustic transfer functions at several receiver positions in front of the wall. The complexity for different wall configurations has been examined and the changes have been achieved by altering its acoustic image. The results show that for a homogenous flat wall, the complexity is significant and for a wall including various smaller objects, the complexity is highly dependent on the position of the receiver with respect to the objects.

Lateral resistance of piles near vertical MSE abutment walls.

Science.gov (United States)

2013-03-01

Full scale lateral load tests were performed on eight piles located at various distances behind MSE walls. The objective of the testing was to determine the effect of spacing from the wall on the lateral resistance of the piles and on the force induc...

Radiation testing of thick-wall objects using a linear accelerator or Co-60

International Nuclear Information System (INIS)

Depending on the energy required, a 60 Co source or various types of betatrons and linear accelerators may be used for radiation testing of thick-walled metal parts. While 60 Co sources are easily transported, accelerators are not, but a transportable linear accelerator is described

Basis for revision 2 of the U.S. Nuclear Regulatory Commission's Regulatory Guide 1.99

International Nuclear Information System (INIS)

Randall, P.N.

1986-01-01

Regulatory Guide 1.99. ''Radiation Damage to Reactor Vessel Materials,'' is being updated to reflect recent studies of the physical basis for neutron radiation damage and efforts to correlate damage to chemical composition and fluence. Revision 2 of the Guide contains several significant changes. Welds and base metal are treated separately. Nickel content is added as a variable and phosphorus removed. The exponent in the fluence factor is reduced, especially at high fluences. And, guidance is given for calculating attenuation of damage through the vessel wall. This paper describes the basis for these changes in the Guide

Abdominal wall closure in bladder exstrophy complex repair by ...

African Journals Online (AJOL)

Background and Objectives: The Exstrophy Complex (EC) is a serious malformation of midline abdominal wall. Wide pubis prevents approximating the lateralized rectus muscle and leads to dehiscence and fi stula formation. Our aim was to recommend an easier method for abdominal wall closure in the Bladder Exstrophy ...

The influence of wall resonances on the levitation of objects in a single-axis acoustic processing chamber

Science.gov (United States)

Ross, B. B.

1980-01-01

Instabilities were observed in high temperature, single axis acoustic processing chambers. At certain temperatures, strong wall resonances were generated within the processing chamber itself and these transverse resonances were thought sufficient to disrupt the levitation well. These wall resonances are apparently not strong enough to cause instabilities in the levitation well.

RAF/9/049: Enhancing and Sustaining the National Regulatory Bodies for safety

International Nuclear Information System (INIS)

Keter, C.J.

2017-01-01

The main objective of this project is to enhance regulatory infrastructure, sustainability and cooperation among national regulatory bodies. This will support strengthening of the existing regulatory framework and capacity building in the region. Self-Assessment using the Self-Assessment Regulatory Infrastructure for Safety (SARIS) was completed on 26th May 2016. Changes made to the legislation is ongoing. The Nuclear Regulatory Bill 2017 is at an advanced stage and about to be tabled to Cabinet. The project objectives shall be addressed under a new project, RAF/9/058 – Improving the Regulatory Framework for the Control of Radiation Sources in Member States. Two major tasks for Kenya to focus include Review of regulations on waste safety, radiation sources and on safety of NPP and advising on drafting of radiation safety guides

Achievement of process control, safety, and regulatory compliance in a mixed waste evaporator system at the Hanford Site using data quality objectives

International Nuclear Information System (INIS)

Von Bargen, B.H.

1995-01-01

The Data Quality Objectives (DQO) Process was applied to the operation of the 242-A Evaporator at the Hanford Site. A team consisting of representatives from process engineering, environmental engineering, regulatory compliance, analytical laboratories, and DOE utilized the step by step DQO process to define the issues, variables, and inputs necessary to develop the decision rules which govern plant operations. The sampling and analyses required to make these decisions was then optimized concerning factors such as sample number, total analyses, cost, radiation exposure, quality assurance, and deliverables

Active compliant wall for skin friction reduction

International Nuclear Information System (INIS)

Pätzold, A.; Peltzer, I.; Nitsche, W.; Goldin, N.; King, R.; Haller, D.; Woias, P.

2013-01-01

Highlights: • Objective: Delay of laminar-turbulent transition on a wing by active wall actuation. • Natural, convective TS-instabilities are damped by travelling counter waves. • Piezo driven active wall and model predictive controller were developed. • TS amplitudes were damped by 83.6% (equals 15.7 dB within instability band). • Significant effect on skin friction distribution. -- Abstract: In order to reduce skin friction drag, an active laminarisation method is developed. Laminar-turbulent boundary layer transition caused by Tollmien–Schlichting (TS) waves is delayed by attenuation of these convective instabilities. An actively driven compliant wall is integrated as part of a wing’s surface. Different configurations of piezo-based actuators are combined with an array of sensitive surface flow sensors. Wall-normal actuation as well as inclined wall displacement are investigated. Together with a realtime-control strategy, transition onset is shifted downstream by six average TS-wave lengths. Using the example of flow velocity, the influence of variable flow conditions on TS-damping rates was investigated. Besides, the boundary layer flow downstream of the active wall area as well as required wall deflections and the global damping effect on skin friction are presented in this paper

Diagnosis of bronchiectasis and airway wall thickening in children with cystic fibrosis

DEFF Research Database (Denmark)

Kuo, Wieying; de Bruijne, Marleen; Petersen, Jens

2017-01-01

Objectives: To quantify airway and artery (AA)-dimensions in cystic fibrosis (CF) and control patients for objective CT diagnosis of bronchiectasis and airway wall thickness (AWT). Methods: Spirometer-guided inspiratory and expiratory CTs of 11 CF and 12 control patients were collected retrospect......Objectives: To quantify airway and artery (AA)-dimensions in cystic fibrosis (CF) and control patients for objective CT diagnosis of bronchiectasis and airway wall thickness (AWT). Methods: Spirometer-guided inspiratory and expiratory CTs of 11 CF and 12 control patients were collected...... following airway generation (p

The dynamic interplay of plasma membrane domains and cortical microtubules in secondary cell wall patterning

Directory of Open Access Journals (Sweden)

Yoshihisa eOda

2013-12-01

Full Text Available Patterning of the cellulosic cell wall underlies the shape and function of plant cells. The cortical microtubule array plays a central role in the regulation of cell wall patterns. However, the regulatory mechanisms by which secondary cell wall patterns are established through cortical microtubules remain to be fully determined. Our recent study in xylem vessel cells revealed that a mutual inhibitory interaction between cortical microtubules and distinct plasma membrane domains leads to distinctive patterning in secondary cell walls. Our research revealed that the recycling of active and inactive ROP proteins by a specific GAP and GEF pair establishes distinct de novo plasma membrane domains. Active ROP recruits a plant-specific microtubule-associated protein, MIDD1, which mediates the mutual interaction between cortical microtubules and plasma membrane domains. In this mini review, we summarize recent research regarding secondary wall patterning, with a focus on the emerging interplay between plasma membrane domains and cortical microtubules through MIDD1 and ROP.

Regulatory agencies and regulatory risk

OpenAIRE

Knieps, Günter; Weiß, Hans-Jörg

2008-01-01

The aim of this paper is to show that regulatory risk is due to the discretionary behaviour of regulatory agencies, caused by a too extensive regulatory mandate provided by the legislator. The normative point of reference and a behavioural model of regulatory agencies based on the positive theory of regulation are presented. Regulatory risk with regard to the future behaviour of regulatory agencies is modelled as the consequence of the ex ante uncertainty about the relative influence of inter...

The Safety Culture of an Effective Nuclear Regulatory Body

International Nuclear Information System (INIS)

Carlsson, Lennart; Bernard, Benoit; Lojk, Robert; Koskinen, Kaisa; Rigail, Anne-Cecile; Stoppa, Gisela; Lorand, Ferenc; Aoki, Masahiro; Fujita, Kenichi; Takada, Hiroko; Kurasaki, Takaaki; Choi, Young Sung; Smit, Martin; Bogdanova, Tatiana; Sapozhnikov, Alexander; Smetnik, Alexander; Cid Campo, Rafael; Axelsson, Lars; Carlsson, Lennart; Edland, Anne; Ryser, Cornelia; Cohen, Miriam; Ficks, Ben; Valentin, Andrea; Nicic, Adriana; Lorin, Aurelie; Nezuka, Takayoshi; Creswell, Len

2016-01-01

The fundamental objective of all nuclear safety regulatory bodies is to ensure that activities related to the peaceful use of nuclear energy are carried out in a safe manner within their respective countries. In order to effectively achieve this objective, the nuclear regulatory body requires specific characteristics, one of which is a healthy safety culture. This regulatory guidance report describes five principles that support the safety culture of an effective nuclear regulatory body. These principles concern leadership for safety, individual responsibility and accountability, co-operation and open communication, a holistic approach, and continuous improvement, learning and self-assessment. The report also addresses some of the challenges to a regulatory body's safety culture that must be recognised, understood and overcome. It provides a unique resource to countries with existing, mature regulators and can be used for benchmarking as well as for training and developing staff. It will also be useful for new entrant countries in the process of developing and maintaining an effective nuclear safety regulator. (authors)

Regulatory authority information system RAIS

International Nuclear Information System (INIS)

Ortiz, P.; Mrabit, K.; Miaw, S.

2000-01-01

In this lecture the principles of the regulatory authority information system (RAIS) are presented. RAIS is a tool currently being developed by the IAEA for the Regulatory Authorities. It is a part of a set of supporting actions designed to assist member states in achieving the objectives of the Model project on radiation and waste safety infrastructure. RAIS is a tool that provides the management of the Regulatory Authority with the key information needed for the planning and implementation of activities and to ensure confidence that resources are optimally used. The RAIS contains five modules: Inventory of installations and radiation sources; Authorization process; Inspection and follow-up actions; Information on personal dosimetry; Assessment of effectiveness by means of performance indicators

Enabling legislation and regulatory determinations for a nuclear power programme

International Nuclear Information System (INIS)

Ha Vinh Phuong

1977-01-01

General remarks on objectives and scope of enabling legislation, on the regulatory body and on the IAEA activities and assistance in regulatory matters e.g. the IAEA Safety Guides which are in preparation. (HP) [de

Regulatory analysis technical evaluation handbook. Final report

International Nuclear Information System (INIS)

1997-01-01

The purpose of this Handbook is to provide guidance to the regulatory analyst to promote preparation of quality regulatory analysis documents and to implement the policies of the Regulatory Analysis Guidelines of the US Nuclear Regulatory Commission (NUREG/BR-0058 Rev. 2). This Handbook expands upon policy concepts included in the NRC Guidelines and translates the six steps in preparing regulatory analyses into implementable methodologies for the analyst. It provides standardized methods of preparation and presentation of regulatory analyses, with the inclusion of input that will satisfy all backfit requirements and requirements of NRC's Committee to Review Generic Requirements. Information on the objectives of the safety goal evaluation process and potential data sources for preparing a safety goal evaluation is also included. Consistent application of the methods provided here will result in more directly comparable analyses, thus aiding decision-makers in evaluating and comparing various regulatory actions. The handbook is being issued in loose-leaf format to facilitate revisions. NRC intends to periodically revise the handbook as new and improved guidance, data, and methods become available

Genomic regulatory landscapes and chromosomal rearrangements

DEFF Research Database (Denmark)

Ladegaard, Elisabete L Engenheiro

2008-01-01

The main objectives of the PhD study are to identify and characterise chromosomal rearrangements within evolutionarily conserved regulatory landscapes around genes involved in the regulation of transcription and/or development (trans-dev genes). A frequent feature of trans-dev genes is that they ......The main objectives of the PhD study are to identify and characterise chromosomal rearrangements within evolutionarily conserved regulatory landscapes around genes involved in the regulation of transcription and/or development (trans-dev genes). A frequent feature of trans-dev genes...... the complex spatio-temporal expression of the associated trans-dev gene. Rare chromosomal breakpoints that disrupt the integrity of these regulatory landscapes may be used as a tool, not only to make genotype-phenotype associations, but also to link the associated phenotype with the position and tissue...... specificity of the individual CNEs. In this PhD study I have studied several chromosomal rearrangements with breakpoints in the vicinity of trans-dev genes. This included chromosomal rearrangements compatible with known phenotype-genotype associations (Rieger syndrome-PITX2, Mowat-Wilson syndrome-ZEB2...

National Program Initiative to Prevent Illicit Trafficking for Radioactive Materials Out of Regulatory Control at the Border

International Nuclear Information System (INIS)

Suharyanta, S.

2016-01-01

The existing function of regulatory authority in a country which use a lot of radioactive sources is important key. The regulatory body has to in a position independence from other operators and nuclear research centre activities, so that their justification on Regulatory objective of safety and security can be achieved. The essential function of regulatory authority has to be represented such as development regulations, perform review and assessment, inspection and enforcement, and emergency preparedness and response functions. Under regulatory object coverage is divided into two clusters i.e. licensed nuclear installation and radiation facilities clusters,. There is other regulatory object is radioactive material out of regulatory control. This kind object is new option in the county and there for need priority policy judgement. This paper will discuss the Regulatory infrastructure and functions and it focused on the experience about National Programme Initiative to Prevent Illicit Trafficking for Radioactive Materials out of Regulatory Control at the Border. Regulatory Infrastructure and Functions. In Indonesia the independent regulatory authority ''called BAPETEN'' has been established since early 2000 based on the Act No. 10 year 1997, independent from operator organization and other nuclear research centre. Organization structure of BAPETEN has defined main divisions dealing with developing regulations, perform review and assessments, inspection and enforcement, and emergency preparedness and response, and also covered assessment function as a backup technical support division as a think-tank functions. Regulatory objects are nuclear installations such as three research reactors, Fuel fabrication facility, Isotope production facility, and waste storage facility for spent fuel and dis-used radioactive sources is running well. Recently, Regulatory of radioactive sources out of regulatory control is a new challenges, they need strengthened

Improving nuclear regulation. NEA regulatory guidance booklets volumes 1-14

International Nuclear Information System (INIS)

2011-01-01

A common theme throughout the series of NEA regulatory guidance reports, or 'green booklets', is the premise that the fundamental objective of all nuclear safety regulatory bodies is to ensure that nuclear facilities are continuously maintained and operated in an acceptably safe manner. In meeting this objective the regulator must bear in mind that it is the operator that has responsibility for safely operating the nuclear facility; the role of the regulator is to assess and to provide assurance regarding the operator's activities in terms of assuming that responsibility. The full series of these reports was brought together in one edition for the first time in 2009 and was widely found to be a useful resource. This second edition comprises 14 volumes, including the latest on The Nuclear Regulator's Role in Assessing Licensee Oversight of Vendor and Other Contracted Services. The reports address various challenges that could apply throughout the lifetime of a nuclear facility, including design, siting, manufacturing, construction, commissioning, operation, maintenance and decommissioning. The compilation is intended to serve as a knowledge management tool both for current regulators and the new nuclear professionals and organisations entering the regulatory field. Contents: Executive Summary; Regulatory Challenges: 1. The Role of the Nuclear Regulator in Promoting and Evaluating Safety Culture; 2. Regulatory Response Strategies for Safety Culture Problems; 3. Nuclear Regulatory Challenges Related to Human Performance; 4. Regulatory Challenges in Using Nuclear Operating Experience; 5. Nuclear Regulatory Review of Licensee Self-assessment (LSA); 6. Nuclear Regulatory Challenges Arising from Competition in Electricity Markets; 7. The Nuclear Regulatory Challenge of Judging Safety Back-fits; 8. The Regulatory Challenges of Decommissioning Nuclear Reactors; 9. The Nuclear Regulator's Role in Assessing Licensee Oversight of Vendor and Other Contracted Services

Pattern of abdominal wall herniae in females: a retrospective analysis

African Journals Online (AJOL)

Background: Gender differences are expected to influence the pattern and outcome of management of abdominal wall hernias. Some of these are left to speculations with few published articles on hernias in females. Objectives: To describe the clinical pattern of abdominal wall hernias in females. Method: A 5 year ...

Assessing corrosion of MSE wall reinforcement.

Science.gov (United States)

2010-09-01

The primary objective of this study was to extract reinforcement coupons from select MSE walls and document the extent of corrosion. In doing this, a baseline has been established against which coupons extracted in the future can be compared. A secon...

Aspergillus fumigatus Trehalose-Regulatory Subunit Homolog Moonlights To Mediate Cell Wall Homeostasis through Modulation of Chitin Synthase Activity

Directory of Open Access Journals (Sweden)

Arsa Thammahong

2017-04-01

Full Text Available Trehalose biosynthesis is found in fungi but not humans. Proteins involved in trehalose biosynthesis are essential for fungal pathogen virulence in humans and plants through multiple mechanisms. Loss of canonical trehalose biosynthesis genes in the human pathogen Aspergillus fumigatus significantly alters cell wall structure and integrity, though the mechanistic link between these virulence-associated pathways remains enigmatic. Here we characterize genes, called tslA and tslB, which encode proteins that contain domains similar to those corresponding to trehalose-6-phosphate phosphatase but lack critical catalytic residues for phosphatase activity. Loss of tslA reduces trehalose content in both conidia and mycelia, impairs cell wall integrity, and significantly alters cell wall structure. To gain mechanistic insights into the role that TslA plays in cell wall homeostasis, immunoprecipitation assays coupled with liquid chromatography-tandem mass spectrometry (LC-MS/MS were used to reveal a direct interaction between TslA and CsmA, a type V chitin synthase enzyme. TslA regulates not only chitin synthase activity but also CsmA sub-cellular localization. Loss of TslA impacts the immunopathogenesis of murine invasive pulmonary aspergillosis through altering cytokine production and immune cell recruitment. In conclusion, our data provide a novel model whereby proteins in the trehalose pathway play a direct role in fungal cell wall homeostasis and consequently impact fungus-host interactions.

Monopoles, vortices, domain walls and D-branes: The rules of interaction

International Nuclear Information System (INIS)

Sakai, Norisuke; Tong, David

2005-01-01

Non-abelian gauge theories in the Higgs phase admit a startling variety of BPS solitons. These include domain walls, vortex strings, confined monopoles threaded on vortex strings, vortex strings ending on domain walls, monopoles threaded on strings ending on domain walls, and more. After presenting a self-contained review of these objects, including several new results on the dynamics of domain walls, we go on to examine the possible interactions of solitons of various types. We point out the existence of a classical binding energy when the string ends on the domain wall which can be thought of as a BPS boojum with negative mass. We present an index theorem for domain walls in non-abelian gauge theories. We also answer questions such as: Which strings can end on which walls? What happens when monopoles pass through domain walls? What happens when domain walls pass through each other? (author)

Thermal insulation properties of walls

Directory of Open Access Journals (Sweden)

Zhukov Aleksey Dmitrievich

2014-05-01

Full Text Available Heat-protective qualities of building structures are determined by the qualities of the used materials, adequate design solutions and construction and installation work of high quality. This rule refers both to the structures made of materials similar in their structure and nature and mixed, combined by a construction system. The necessity to ecaluate thermal conductivity is important for a product and for a construction. Methods for evaluating the thermal protection of walls are based on the methods of calculation, on full-scale tests in a laboratory or on objects. At the same time there is a reason to believe that even deep and detailed calculation may cause deviation of the values from real data. Using finite difference method can improve accuracy of the results, but it doesn’t solve all problems. The article discusses new approaches to evaluating thermal insulation properties of walls. The authors propose technique of accurate measurement of thermal insulation properties in single blocks and fragments of walls and structures.

Diagnosis of pelvic wall tumor on multislice CT

International Nuclear Information System (INIS)

Zhang Keyun; Deng Lequn; Lei Hongwei

2011-01-01

Objective: To evaluate the value of multi-slice CT (MSCT) in diagnosing pelvic wall tumors. Methods: MSCT of 21 cases of pelvic wall tumors including metastasis (10), neurogenic tumor (5), chondrosarcoma (2), chordoma (1), aneurysmal bone cyst (1), giant cell tumor (1), and osteochondroma (1) was retrospectively analyzed. Results: CT appearances of pelvic wall tumors include bony destruction and soft tissue masses. Common features were bone destruction in metastasis, expansion of the neuroforamen in neurogenic tumor, pleomorphic calcification in chondrosarcoma, lower sacral vertebral location of chordoma, iliac crest bone destruction in giant cell tumor, cauliflower-like nodules in osteochondroma. Conclusion: MSCT with three-dimensional volume rendering demonstrates well the tumor shape, size, extent, internal structure and relationship with the surrounding organs to aid diagnosis of pelvic wall tumors. (authors)

Regulatory Inspection of Nuclear Power Plants in NEA Member Countries

International Nuclear Information System (INIS)

1978-01-01

Based on the replies to a questionnaire, this report gives a description and comparative evaluation of the regulatory inspection activities in several NEA Member countries. The questionnaire which was circulated to all Member countries requested details on the organisation, system, scope and objectives of nuclear regulatory inspection and the effort required throughout all stages of the life of a nuclear plant including the use of independent bodies or consultants. Additional information was requested on the documentation concerned with regulatory inspections, incident and accident reporting procedures, and the duties, powers and bases for recruitment of regulatory personnel with the object of covering all related aspects. However, because of the differences in national practices and perhaps in the interpretation of the questionnaire, it proved to be extremely difficult to make an evaluation and comparison of inspection activities and effort involved in these Member countries. This report, which includes a section on the nuclear power programme in Member countries, should therefore only be regarded as an initial review but it provides a useful contribution to the exchange of experience and views on regulatory inspection practices

Distribution of alginate and cellulose and regulatory role of calcium in the cell wall of the brown alga Ectocarpus siliculosus (Ectocarpales, Phaeophyceae).

Science.gov (United States)

Terauchi, Makoto; Nagasato, Chikako; Inoue, Akira; Ito, Toshiaki; Motomura, Taizo

2016-08-01

This work investigated a correlation between the three-dimensional architecture and compound-components of the brown algal cell wall. Calcium greatly contributes to the cell wall integrity. Brown algae have a unique cell wall consisting of alginate, cellulose, and sulfated polysaccharides. However, the relationship between the architecture and the composition of the cell wall is poorly understood. Here, we investigated the architecture of the cell wall and the effect of extracellular calcium in the sporophyte and gametophyte of the model brown alga, Ectocarpus siliculosus (Dillwyn) Lyngbye, using transmission electron microscopy, histochemical, and immunohistochemical studies. The lateral cell wall of vegetative cells of the sporophyte thalli had multilayered architecture containing electron-dense and negatively stained fibrils. Electron tomographic analysis showed that the amount of the electron-dense fibrils and the junctions was different between inner and outer layers, and between the perpendicular and tangential directions of the cell wall. By immersing the gametophyte thalli in the low-calcium (one-eighth of the normal concentration) artificial seawater medium, the fibrous layers of the lateral cell wall of vegetative cells became swollen. Destruction of cell wall integrity was also induced by the addition of sorbitol. The results demonstrated that electron-dense fibrils were composed of alginate-calcium fibrous gels, and electron negatively stained fibrils were crystalline cellulose microfibrils. It was concluded that the spatial arrangement of electron-dense fibrils was different between the layers and between the directions of the cell wall, and calcium was necessary for maintaining the fibrous layers in the cell wall. This study provides insights into the design principle of the brown algal cell wall.

Wall Turbulence with Designer Properties: Identification, Characterization and Manipulation of Energy Pathways

Science.gov (United States)

2016-02-26

AFRL-AFOSR-VA-TR-2016-0108 Wall turbulence with designer properties Beverley Mckeon CALIFORNIA INSTITUTE OF TECHNOLOGY Final Report 02/26/2016... Wall turbulence with designer properties: Identification, characterization & manipulation of energy pathways 5a. CONTRACT NUMBER 5b. GRANT NUMBER...identification, characterization and manipulation of energy pathways in wall turbulence . The objectives were pursued separately and collaboratively by the

Brick walls on the brane

International Nuclear Information System (INIS)

Medved, A J M

2002-01-01

The so-called 'brick-wall model' is a semiclassical approach that has been used to explain black hole entropy in terms of thermal matter fields. Here, we apply the brick-wall formalism to thermal bulk fields in a Randall-Sundrum brane world scenario. In this case, the black hole entity is really a string-like object in the anti-de Sitter bulk, while appearing as a Schwarzchild black hole to observers living on the brane. In spite of these exotic circumstances, we establish that the Bekenstein-Hawking entropy law is preserved. Although a similar calculation was recently considered in the literature, this prior study invoked a simplifying assumption (which we avoid) that cannot be adequately justified

Design method of high performance precast external walls for warm climate by multi-objective optimization analysis

International Nuclear Information System (INIS)

Baglivo, Cristina; Congedo, Paolo Maria

2015-01-01

Taking into account the global environmental problems, there is the urgent need to reduce energy consumption and the greenhouse gas emissions in the construction sector. Environmental awareness can be achieved through the extensive application of precast systems in buildings construction. A multi-criteria analysis has been used to obtain energy-efficient precast walls for Zero Energy Building in warm climate focusing on eco-friendly building materials. The modeFRONTIER optimization tool, with the use of computational procedures developed in Matlab, has been used to assess the thermal dynamics of building components. The optimization has been carried out in terms of steady thermal transmittance, periodic thermal transmittance, decrement factor, time shift, areal heat capacity, thermal admittance, surface mass, small thickness, eco sustainability score, light-weight and costs. The best sequences of layers show repetitive features: high surface mass for the first layer (internal side), followed by eco-friendly insulating materials for the middle layer and common insulating materials for the outer layer. The results illustrate that it is possible to obtain high performance precast multi-layered walls also with light and thin solutions; in particular, the superficial mass and the internal areal heat capacity have an important role to obtain the best performance in the warm climate. - Highlights: • Environmental awareness through the application of prefabrication systems. • The precast allows important benefits compared to traditional walls build in situ. • At the end of their useful life, the precast can be re-used. • Precast walls with very high efficiency for warm climates. • High internal areal heat capacity avoids events of overheating/cooling down.

Radiological diagnosis of chest wall tuberculosis: CT versus chest radiograph

International Nuclear Information System (INIS)

Liu Fugeng; Pan Jishu; Chen Qihang; Zhou Cheng; Yu Jingying; Tang Dairong

2006-01-01

Objective: To evaluate the role of CT or Chest radiograph in diagnosis of chest wall tuberculosis. Methods: The study population included 21 patients with chest wall tuberculosis confirmed by operation or biopsy. Chest radiograph and plain CT were performed in all eases, while enhanced CT in 9 cases, and all images were reviewed by 2 radiologists. Results: Single soft tissue mass of the chest wall was detected in all cases on CT, but not on chest radiograph(χ 2 =42.000, P 2 =4.421, P<0.05). Conclusion: CT, especially enhanced CT scan is the first choice in the diagnosis of chest wall tuberculosis. (authors)

Using the IRRS to Strengthen Regulatory Competence in Ireland

International Nuclear Information System (INIS)

Smith, K.

2016-01-01

In 2015, Ireland underwent an IRRS (Integrated Regulatory Review Service) review mission. The purpose of the mission was to review Ireland’s radiation and nuclear safety regulatory framework and activities against the relevant IAEA safety standards, to report on the regulatory effectiveness and to exchange information and experience in the areas covered by the IRRS. The review mission was well-timed as there had been recent changes in the regulatory infrastructure with the merger of the Radiological Protection Institute of Ireland (RPII) and the Environmental Protection Agency (EPA) in 2014, as well as the upcoming implementation of the new Euratom Basic Safety Standards (BSS) Directive. The key objectives of the mission were to enhance the national legal, governmental and regulatory framework for nuclear and radiation safety, and national arrangements for emergency preparedness and response. The agreed scope of the review covered all relevant facilities and activities regulated in Ireland and also included medical exposures and public exposure to radon. In advance of the mission, Ireland completed a process of self-assessment and review. This process identified strengths and weaknesses in the national regulatory framework compared with the international standards. In addition to the value of having Ireland’s radiation protection framework peer reviewed by senior international experts, the mission helped to further strengthen links between all the national bodies (government, licensees, regulatory) with a role in the regulation of radiation safety. The findings from the IRRS review team’s objective evaluation of Ireland’s regulatory infrastructure are being used to prioritise actions for strengthening the regulatory framework, to provide input into the transposition of the Euratom BSS, and to support the revision of the national emergency plan for nuclear accidents. It is planned to have addressed the findings of the IRRS mission in advance of a follow up

The Regulatory Independence of FANR

International Nuclear Information System (INIS)

ALNuaimi, Fatema; Choi, Kwang Shik

2012-01-01

Regulatory independence is meant to provide a conservative system of policy making in order to comply with the problems that are forecasted upon the basis of assumptions. The Federal Authorization of Nuclear Regulation (FANR) is a regulatory commission that was formed to be regulatory body that governs the generation of nuclear power in United Arab Emirates. It was established under the UAE nuclear law (9/2009) as an independent regulatory body that was tasked with the regulation of all nuclear activities in the United Arab Emirates. As an independent body, FANR was tasked with ensuring that the regulation of the nuclear sector is done in effective and transparent manner to ensure its accountability to the people. Being independent, the regulatory body develops national nuclear regulations based on laid down safety standards by the International Atomic Energy Agency, ensuring that they are based on scientific and proven technologies The role of FANR is to ensure that the all corporations that undertake nuclear activities follow the laid down procedures and objectives and ensure safety measures are taken keenly to ensure the safety of the workers and the general public while at the same time ensuring the environment is free from nuclear radiations

The Regulatory Independence of FANR

Energy Technology Data Exchange (ETDEWEB)

ALNuaimi, Fatema; Choi, Kwang Shik [Korea Advanced Institute of Science and Technology, Daejeon (Korea, Republic of)

2012-05-15

Regulatory independence is meant to provide a conservative system of policy making in order to comply with the problems that are forecasted upon the basis of assumptions. The Federal Authorization of Nuclear Regulation (FANR) is a regulatory commission that was formed to be regulatory body that governs the generation of nuclear power in United Arab Emirates. It was established under the UAE nuclear law (9/2009) as an independent regulatory body that was tasked with the regulation of all nuclear activities in the United Arab Emirates. As an independent body, FANR was tasked with ensuring that the regulation of the nuclear sector is done in effective and transparent manner to ensure its accountability to the people. Being independent, the regulatory body develops national nuclear regulations based on laid down safety standards by the International Atomic Energy Agency, ensuring that they are based on scientific and proven technologies The role of FANR is to ensure that the all corporations that undertake nuclear activities follow the laid down procedures and objectives and ensure safety measures are taken keenly to ensure the safety of the workers and the general public while at the same time ensuring the environment is free from nuclear radiations

2009 Plant Cell Walls Gordon Research Conference-August 2-7,2009

Energy Technology Data Exchange (ETDEWEB)

Mohnen, Debra [Univ. of Georgia, Athens, GA (United States)

2009-08-07

Plant cell walls are a complex cellular compartment essential for plant growth, development and response to biotic and abiotic stress and a major biological resource for meeting our future bioenergy and natural product needs. The goal of the 2009 Plant Cell Walls Gordon Research Conference is to summarize and critically evaluate the current level of understanding of the structure, synthesis and function of the whole plant extracellular matrix, including the polysaccharides, proteins, lignin and waxes that comprise the wall, and the enzymes and regulatory proteins that drive wall synthesis and modification. Innovative techniques to study how both primary and secondary wall polymers are formed and modified throughout plant growth will be emphasized, including rapid advances taking place in the use of anti-wall antibodies and carbohydrate binding proteins, comparative and evolutionary wall genomics, and the use of mutants and natural variants to understand and identify wall structure-function relationships. Discussions of essential research advances needed to push the field forward toward a systems biology approach will be highlighted. The meeting will include a commemorative lecture in honor of the career and accomplishments of the late Emeritus Professor Bruce A. Stone, a pioneer in wall research who contributed over 40 years of outstanding studies on plant cell wall structure, function, synthesis and remodeling including emphasis on plant cell wall beta-glucans and arabinogalactans. The dwindling supply of fossil fuels will not suffice to meet our future energy and industrial product needs. Plant biomass is the renewable resource that will fill a large part of the void left by vanishing fossil fuels. It is therefore critical that basic research scientists interact closely with industrial researchers to critically evaluate the current state of knowledge regarding how plant biomass, which is largely plant cell walls, is synthesized and utilized by the plant. A final

Diagnosis of the Brazilian Nuclear Regulatory body

International Nuclear Information System (INIS)

Santos Gomes, Rogerio dos; Magalhaes Ennes Ennes, Edson Carlos

2008-01-01

This work has the objective to present the diagnosis of the existing structure in the Brazilian Government to ensure the radioprotection and nuclear safety in the country, being compared the current situation with the conclusions presented in another studies, carried through in last 30 years, with special attention in the existence of the necessary available to support and independence of the national regulatory body for the development of the regulatory inspections activities in the radioprotection and nuclear safety. (author)

PtrWRKY19, a novel WRKY transcription factor, contributes to the regulation of pith secondary wall formation in Populus trichocarpa

OpenAIRE

Li Yang; Xin Zhao; Fan Yang; Di Fan; Yuanzhong Jiang; Keming Luo

2016-01-01

WRKY proteins are one of the largest transcription factor families in higher plants and play diverse roles in various biological processes. Previous studies have shown that some WRKY members act as negative regulators of secondary cell wall formation in pith parenchyma cells. However, the regulatory mechanism of pith secondary wall formation in tree species remains largely unknown. In this study, PtrWRKY19 encoding a homolog of Arabidopsis WRKY12 was isolated from Populus trichocarpa. PtrWRKY...

CT-Sellink - a new method for demonstrating the gut wall

International Nuclear Information System (INIS)

Thiele, J.; Kloeppel, R.; Schulz, H.G.

1993-01-01

34 patients were examined by CT following a modified enema (CT-Sellink) in order to demonstrate the gut. By introducing a 'gut index' it is possible to define the tone of the gut providing its folds remain constant. By means of a radial density profile the gut wall can be defined objectively and in numerical terms. Gut wall thickness in the small bowel averaged 1.2 mm with a density of 51 Hu and gut wall thickness in the colon averaged 2 mm with a density of 59 Hu. (orig.) [de

Implementation of safety goals in NRC's regulatory process

International Nuclear Information System (INIS)

Murley, T.E.

1985-01-01

In May 1983 the Nuclear Regulatory Commission issued a policy statement on Safety Goals For Nuclear Power Plant Operation. The Commission at the same time judged that a two-year evaluation period was necessary to judge the effectiveness of the goals and design objectives, and directed the staff to develop information and understanding as to how to further define and use the design objectives and the cost-benefit guidelines. In carrying out the Commission's mandate, the staff framed three major questions to be addressed during the safety goal evaluation period. These three questions are: 1) to what extent is it practical to use safety goals in the regulatory process. 2) Should the quantitative design objectives be modified or supplemented. If so, how. 3) How should the safety goals be implemented at the end of the evaluation period. The staff's conclusions are discussed

An overview of an experimental program for testing large reinforced concrete shear walls

International Nuclear Information System (INIS)

Farrar, C.R.; Bennett, J.G.

1989-01-01

The Seismic Category I Structures Program is being carried out at the Los Alamos National Laboratory under sponsorship of the US Nuclear Regulatory Commission (NRC), Office of Nuclear Regulatory Research. In the class of structure being investigated, the primary lateral load-resisting structural element is the reinforced concrete shear wall. Previous results from microconcrete models indicated that these structures responded to seismic excitations with initial frequencies that were reduced by factors of 2 or more over those calculated based on an uncracked cross-section strength-of-materials approach. Furthermore, though the structures themselves were shown to have sufficient reserve margins, the equipment and piping are designed to response spectra that are based on uncracked cross-sectional member properties, and these spectra may not be inappropriate for actual building responses. The current phase of the program is aimed at verification of these conclusions using conventional concrete structures to demonstrate that previous microconcrete results can be scaled to prototype structures. A new configuration of a shear wall structure was designed and tested to investigate the analytical-experimental differences observed during the previous model testing. Shear wall height-to-length aspect ratios were to vary from 1 to 0.25. Percentage steel ratios were to vary from 0.25% to 0.6% by area, in both horizontal and vertical directions. The test structures are shown in Fig. 1. TRG-1 and -2 were constructed with microconcrete. TRG-3, -4, -5, and -6 were constructed with conventional (19-mm aggregate) concrete. 11 refs., 4 figs

Preliminary Consideration for the Development of Regulatory Level 2 PSA Model

International Nuclear Information System (INIS)

Lee, Chang-Ju

2006-01-01

In order to assess the validity of PSA (probabilistic safety assessment) results and to establish regulatory requirements for relevant safety issues most of the regulators want to develop an independent and convenient risk assessment model including Level 2 PSA area. As this model and framework should be implicitly independent on the licensee's PSA model, it has a primary objective directly for applying to the risk-informed regulatory affairs and for supporting those kinds of works. According this, the regulator can take an objective view for the uncertainty of risk information made by the licensee and keep up the capability and decision-making framework for overall risk assessment results. In addition, the regulatory model may be used to verify and validate the operational risk levels of all engineered safety features of nuclear power plants (NPPs). An issue for plant-specific application of safety goals was previously identified in the US NRC's risk-informed regulatory guidance development activities, and discussed in many Commission papers, e. g. SECY-97-287, which identifies the goal for large early release frequency (LERF). LERF defines a containment performance criteria derived from the quantitative health objectives. As we know, the LERF was chosen to assess risk significance in Regulatory Guide 1.174 (2002) again, which provides one measure of the performance of the containment barrier, and represents a surrogate for early health effects

Regulation for continuous improvements - the new regulatory strategy of SKI

International Nuclear Information System (INIS)

Hoegberg, L.; Svensson, G.; Viktorsson, C.

1998-01-01

This paper describes the new regulatory objectives and strategy of the Swedish Nuclear Power Inspectorate. Factors that have influenced the development of the regulatory strategy, including an international peer review, are discussed. In addition to general technical requirements for a defence in depth, the new strategy strongly focuses on the quality of plant safety management processes, to be monitored by process-oriented inspections. Also, quality assurance of regulatory activities is stressed. Experience gained so far shows that the regulatory approach chosen in Sweden promotes utility self assessment, quality of safety management and ownership of safety work within the utility staff. (author)

Genetic engineering of grass cell wall polysaccharides for biorefining.

Science.gov (United States)

Bhatia, Rakesh; Gallagher, Joe A; Gomez, Leonardo D; Bosch, Maurice

2017-09-01

Grasses represent an abundant and widespread source of lignocellulosic biomass, which has yet to fulfil its potential as a feedstock for biorefining into renewable and sustainable biofuels and commodity chemicals. The inherent recalcitrance of lignocellulosic materials to deconstruction is the most crucial limitation for the commercial viability and economic feasibility of biomass biorefining. Over the last decade, the targeted genetic engineering of grasses has become more proficient, enabling rational approaches to modify lignocellulose with the aim of making it more amenable to bioconversion. In this review, we provide an overview of transgenic strategies and targets to tailor grass cell wall polysaccharides for biorefining applications. The bioengineering efforts and opportunities summarized here rely primarily on (A) reprogramming gene regulatory networks responsible for the biosynthesis of lignocellulose, (B) remodelling the chemical structure and substitution patterns of cell wall polysaccharides and (C) expressing lignocellulose degrading and/or modifying enzymes in planta. It is anticipated that outputs from the rational engineering of grass cell wall polysaccharides by such strategies could help in realizing an economically sustainable, grass-derived lignocellulose processing industry. © 2017 The Authors. Plant Biotechnology Journal published by Society for Experimental Biology and The Association of Applied Biologists and John Wiley & Sons Ltd.

Regulatory inspection of the implementation of quality assurance programmes

International Nuclear Information System (INIS)

1989-01-01

This Manual provides guidance to Member States in the organization and performance of their regulatory inspection functions regarding the implementation of nuclear power plant quality assurance programmes. It addresses the interface between, and is consistent with, the IAEA Nuclear Safety Standards (NUSS programme) documents on quality assurance and governmental organization. The Manual offers a practical model and examples for performing regulatory inspections to ensure that the quality assurance programme is operating satisfactorily in the siting, design, manufacturing, construction, commissioning, operation and decommissioning of nuclear power plants. The primary objective is to confirm that the licensee has the capability to manage and control the effective performance of all quality assurance responsibilities during all phases of a nuclear power project. The guidance provided through this Manual for proper establishment and execution of the regulatory inspections helps to enforce the effective implementation of the quality assurance programme as a management control system that the nuclear industry should establish and use in attaining the safety and reliability objectives for nuclear installations. This enforcement action by national regulatory bodies and the emphasis on the purposes and advantages of quality assurance as an important management tool integrated within the total project task have been recommended by the IAEA International Nuclear Safety Advisory Group (INSAG). The primary intended users of this Manual are the management personnel and high level staff from regulatory bodies but it will also be helpful to management personnel from nuclear utilities and vendors. They all are inevitable partners in a nuclear power project and this document offers all of them valuable information on the better accomplishment of quality assurance activities to ensure the common objective of safe and reliable nuclear power production

78 FR 44403 - Unified Agenda of Federal Regulatory and Deregulatory Actions

Science.gov (United States)

2013-07-23

... agenda (the Agenda) in accordance with Public Law 96-354, ``The Regulatory Flexibility Act,'' and... goals; (2) support for the Strategic Plan organizational excellence objectives; (3) a governmental... Flexibility Act Section 610 of the Regulatory Flexibility Act (RFA) requires agencies to conduct a review...

The CWI Pathway: Regulation of the Transcriptional Adaptive Response to Cell Wall Stress in Yeast

Directory of Open Access Journals (Sweden)

Ana Belén Sanz

2017-12-01

Full Text Available Fungi are surrounded by an essential structure, the cell wall, which not only confers cell shape but also protects cells from environmental stress. As a consequence, yeast cells growing under cell wall damage conditions elicit rescue mechanisms to provide maintenance of cellular integrity and fungal survival. Through transcriptional reprogramming, yeast modulate the expression of genes important for cell wall biogenesis and remodeling, metabolism and energy generation, morphogenesis, signal transduction and stress. The yeast cell wall integrity (CWI pathway, which is very well conserved in other fungi, is the key pathway for the regulation of this adaptive response. In this review, we summarize the current knowledge of the yeast transcriptional program elicited to counterbalance cell wall stress situations, the role of the CWI pathway in the regulation of this program and the importance of the transcriptional input received by other pathways. Modulation of this adaptive response through the CWI pathway by positive and negative transcriptional feedbacks is also discussed. Since all these regulatory mechanisms are well conserved in pathogenic fungi, improving our knowledge about them will have an impact in the developing of new antifungal therapies.

Building a Lego wall: Sequential action selection.

Science.gov (United States)

Arnold, Amy; Wing, Alan M; Rotshtein, Pia

2017-05-01

The present study draws together two distinct lines of enquiry into the selection and control of sequential action: motor sequence production and action selection in everyday tasks. Participants were asked to build 2 different Lego walls. The walls were designed to have hierarchical structures with shared and dissociated colors and spatial components. Participants built 1 wall at a time, under low and high load cognitive states. Selection times for correctly completed trials were measured using 3-dimensional motion tracking. The paradigm enabled precise measurement of the timing of actions, while using real objects to create an end product. The experiment demonstrated that action selection was slowed at decision boundary points, relative to boundaries where no between-wall decision was required. Decision points also affected selection time prior to the actual selection window. Dual-task conditions increased selection errors. Errors mostly occurred at boundaries between chunks and especially when these required decisions. The data support hierarchical control of sequenced behavior. (PsycINFO Database Record (c) 2017 APA, all rights reserved).

In vivo wall shear measurements within the developing zebrafish heart.

Directory of Open Access Journals (Sweden)

R Aidan Jamison

Full Text Available Physical forces can influence the embryonic development of many tissues. Within the cardiovascular system shear forces resulting from blood flow are known to be one of the regulatory signals that shape the developing heart. A key challenge in investigating the role of shear forces in cardiac development is the ability to obtain shear force measurements in vivo. Utilising the zebrafish model system we have developed a methodology that allows the shear force within the developing embryonic heart to be determined. Accurate wall shear measurement requires two essential pieces of information; high-resolution velocity measurements near the heart wall and the location and orientation of the heart wall itself. We have applied high-speed brightfield imaging to capture time-lapse series of blood flow within the beating heart between 3 and 6 days post-fertilization. Cardiac-phase filtering is applied to these time-lapse images to remove the heart wall and other slow moving structures leaving only the red blood cell movement. Using particle image velocimetry to calculate the velocity of red blood cells in different regions within the heart, and using the signal-to-noise ratio of the cardiac-phase filtered images to determine the boundary of blood flow, and therefore the position of the heart wall, we have been able to generate the necessary information to measure wall shear in vivo. We describe the methodology required to measure shear in vivo and the application of this technique to the developing zebrafish heart. We identify a reduction in shear at the ventricular-bulbar valve between 3 and 6 days post-fertilization and demonstrate that the shear environment of the ventricle during systole is constantly developing towards a more uniform level.

In vivo wall shear measurements within the developing zebrafish heart.

Science.gov (United States)

Jamison, R Aidan; Samarage, Chaminda R; Bryson-Richardson, Robert J; Fouras, Andreas

2013-01-01

Physical forces can influence the embryonic development of many tissues. Within the cardiovascular system shear forces resulting from blood flow are known to be one of the regulatory signals that shape the developing heart. A key challenge in investigating the role of shear forces in cardiac development is the ability to obtain shear force measurements in vivo. Utilising the zebrafish model system we have developed a methodology that allows the shear force within the developing embryonic heart to be determined. Accurate wall shear measurement requires two essential pieces of information; high-resolution velocity measurements near the heart wall and the location and orientation of the heart wall itself. We have applied high-speed brightfield imaging to capture time-lapse series of blood flow within the beating heart between 3 and 6 days post-fertilization. Cardiac-phase filtering is applied to these time-lapse images to remove the heart wall and other slow moving structures leaving only the red blood cell movement. Using particle image velocimetry to calculate the velocity of red blood cells in different regions within the heart, and using the signal-to-noise ratio of the cardiac-phase filtered images to determine the boundary of blood flow, and therefore the position of the heart wall, we have been able to generate the necessary information to measure wall shear in vivo. We describe the methodology required to measure shear in vivo and the application of this technique to the developing zebrafish heart. We identify a reduction in shear at the ventricular-bulbar valve between 3 and 6 days post-fertilization and demonstrate that the shear environment of the ventricle during systole is constantly developing towards a more uniform level.

An objective method to optimize the MR sequence set for plaque classification in carotid vessel wall images using automated image segmentation.

Directory of Open Access Journals (Sweden)

Ronald van 't Klooster

Full Text Available A typical MR imaging protocol to study the status of atherosclerosis in the carotid artery consists of the application of multiple MR sequences. Since scanner time is limited, a balance has to be reached between the duration of the applied MR protocol and the quantity and quality of the resulting images which are needed to assess the disease. In this study an objective method to optimize the MR sequence set for classification of soft plaque in vessel wall images of the carotid artery using automated image segmentation was developed. The automated method employs statistical pattern recognition techniques and was developed based on an extensive set of MR contrast weightings and corresponding manual segmentations of the vessel wall and soft plaque components, which were validated by histological sections. Evaluation of the results from nine contrast weightings showed the tradeoff between scan duration and automated image segmentation performance. For our dataset the best segmentation performance was achieved by selecting five contrast weightings. Similar performance was achieved with a set of three contrast weightings, which resulted in a reduction of scan time by more than 60%. The presented approach can help others to optimize MR imaging protocols by investigating the tradeoff between scan duration and automated image segmentation performance possibly leading to shorter scanning times and better image interpretation. This approach can potentially also be applied to other research fields focusing on different diseases and anatomical regions.

Interactions of severe accident research and regulatory positions (ISARRP)

International Nuclear Information System (INIS)

Sehgal, B.R.

2001-12-01

The work Programme of the ISARRP Project was divided into several work packages. The work was conducted in the form of presentations and discussions, held during several meetings whose character was that of workshops. Short reports were prepared by the partners assigned to each task. Work Package 1: Critical review of the SA phenomenological research. The objective of this work package was to consider the progress made world-wide in research on the resolution of the outstanding phenomenological issues posed by severe accidents. Work Package 2: Relevance of severe accident research to SAMG requirements and implementation. The objective of this work package was to relate the progress made in the resolution of the SA issues to the practical matter of what results are required or have been used for the management of severe accidents. Clearly, the SAMG is the most important avenue employed by the regulatory organizations to assure themselves of the safe (from public perspective) performance of a nuclear plant in a postulated severe accident event. Work Package 3: Relevance of severe accident research to PSA and the risk informed regulatory approach. The objectives of this work package is to relate the results obtained by the severe accident research to the requirements of a PSA and of the new trend of employing the risk informed approach in promulgating regulations. Clearly a PSA identifies vulnerabilities in the knowledge base, however, their importance is decidedly plant specific. Nevertheless the uncertainties in the phenomenology or in resolution of issues lead to uncertainties in the PSA conclusions and in the adoption of the risk informed approach. Work Package 4: Questionnaire and the evaluation of responses to the questions. The purpose of this work package is to solicit the views of the regulatory organizations towards the results of the SA research and the benefits they have derived from it in terms of regulatory actions, or in the confidence they have gained

Interactions of severe accident research and regulatory positions (ISARRP)

Energy Technology Data Exchange (ETDEWEB)

Sehgal, B.R. (comp.) [Royal Inst. of Tech., Stockholm (Sweden). Nuclear Power Safety

2001-12-01

The work Programme of the ISARRP Project was divided into several work packages. The work was conducted in the form of presentations and discussions, held during several meetings whose character was that of workshops. Short reports were prepared by the partners assigned to each task. Work Package 1: Critical review of the SA phenomenological research. The objective of this work package was to consider the progress made world-wide in research on the resolution of the outstanding phenomenological issues posed by severe accidents. Work Package 2: Relevance of severe accident research to SAMG requirements and implementation. The objective of this work package was to relate the progress made in the resolution of the SA issues to the practical matter of what results are required or have been used for the management of severe accidents. Clearly, the SAMG is the most important avenue employed by the regulatory organizations to assure themselves of the safe (from public perspective) performance of a nuclear plant in a postulated severe accident event. Work Package 3: Relevance of severe accident research to PSA and the risk informed regulatory approach. The objectives of this work package is to relate the results obtained by the severe accident research to the requirements of a PSA and of the new trend of employing the risk informed approach in promulgating regulations. Clearly a PSA identifies vulnerabilities in the knowledge base, however, their importance is decidedly plant specific. Nevertheless the uncertainties in the phenomenology or in resolution of issues lead to uncertainties in the PSA conclusions and in the adoption of the risk informed approach. Work Package 4: Questionnaire and the evaluation of responses to the questions. The purpose of this work package is to solicit the views of the regulatory organizations towards the results of the SA research and the benefits they have derived from it in terms of regulatory actions, or in the confidence they have gained

75 FR 79449 - Introduction to The Regulatory Plan and the Unified Agenda of Federal Regulatory and Deregulatory...

Science.gov (United States)

2010-12-20

... Administration 79677 Office of Personnel Management 79679 Pension Benefit Guaranty Corporation 79681 Small... National Indian Gaming Commission 79706 Postal Regulatory Commission 79708 AGENCY AGENDAS Cabinet... Register twice each year since 1983 and has been available online since 1995. To further the objective of...

Regulatory guide in support of ECCS rule revision

International Nuclear Information System (INIS)

Tovmassian, H.S.

1987-01-01

The US Nuclear Regulatory Commission staff is proposing to amend 10 CFR 50.46 and Appendix K to allow licensees to use best estimate calculations to estimate emergency core cooling system performance. This estimate in conjunction with an estimate of the uncertainty in the calculation would then be used to assure that the licensing limits set forth in 10 CFR 50.46(b) are not exceeded. The NRC staff has prepared a draft regulatory guide to assist licensees and applicants in complying with these proposed amendments. This paper sets forth the objectives of this regulatory guide, the approach taken, the difficulties encountered, and the current status of this effort

Guidelines for IAEA International Regulatory Review Teams (IRRTs)

International Nuclear Information System (INIS)

2002-01-01

The IAEA International Regulatory Review Team (IRRT) programme provides advice and assistance to Member States to strengthen and enhance the effectiveness of the nuclear regulatory body whilst recognizing the ultimate responsibility of each Member State for nuclear safety. The IRRT programme, initiated in 1989, is not restricted to any particular group of Member States, whether developing or industrialized, but is available to all countries with nuclear installations in operation or approaching operation. The basic concepts, purposes and functions of a national regulatory body are well recognized in all Member States having a nuclear power programme. The IAEA Safety Standards Series publication entitled 'Legal and Governmental Infrastructure for Nuclear, Radiation, Radioactive Waste and Transport Safety, Safety: Requirements', No. GS-R-1 (2000), provides a general consensus reference for the practices necessary for a national organization to fulfil the regulatory purposes and discharge the regulatory functions. The Requirements also defines the terms used in these guidelines. The guidance given in the Requirements recognizes that the organizational structure and regulatory processes will vary from country to country depending on their existing constitutional, legal and administrative systems; the size and structure of their nuclear programme; the technical skills and professional and financial resources available to their regulatory body, and social customs and cultural traditions. The objective of this report is to provide guidance on the basic structure of an IRRT mission and provide a common reference both across the various areas covered by an IRRT mission and across all the missions in the programme. As such, it is addressed, principally, to the team members of IRRT missions but it also provides guidance to a host regulatory body receiving a mission. This report identifies the objectives of the IRRT mission and sets out the scope of the topic areas that are

76 FR 13549 - Reducing Regulatory Burden; Retrospective Review Under E.O. 13563

Science.gov (United States)

2011-03-14

...'s regulatory program more effective and less burdensome in achieving its regulatory objectives by... DEPARTMENT OF COMMERCE National Oceanic and Atmospheric Administration 15 CFR Chapter IX 50 CFR.... 13563 AGENCY: National Oceanic and Atmospheric Administration (NOAA), Commerce. ACTION: Request for...

Diagnosis of bronchiectasis and airway wall thickening in children with cystic fibrosis. Objective airway-artery quantification

International Nuclear Information System (INIS)

Kuo, Wieying; Tiddens, Harm A.W.M.; Bruijne, Marleen de; Petersen, Jens; Nasserinejad, Kazem; Ozturk, Hadiye; Chen, Yong; Perez-Rovira, Adria

2017-01-01

To quantify airway and artery (AA)-dimensions in cystic fibrosis (CF) and control patients for objective CT diagnosis of bronchiectasis and airway wall thickness (AWT). Spirometer-guided inspiratory and expiratory CTs of 11 CF and 12 control patients were collected retrospectively. Airway pathways were annotated semi-automatically to reconstruct three-dimensional bronchial trees. All visible AA-pairs were measured perpendicular to the airway axis. Inner, outer and AWT (outer-inner) diameter were divided by the adjacent artery diameter to compute A in A-, A out A- and A WT A-ratios. AA-ratios were predicted using mixed-effects models including disease status, lung volume, gender, height and age as covariates. Demographics did not differ significantly between cohorts. Mean AA-pairs CF: 299 inspiratory; 82 expiratory. Controls: 131 inspiratory; 58 expiratory. All ratios were significantly larger in inspiratory compared to expiratory CTs for both groups (p<0.001). A out A- and A WT A-ratios were larger in CF than in controls, independent of lung volume (p<0.01). Difference of A out A- and A WT A-ratios between patients with CF and controls increased significantly for every following airway generation (p<0.001). Diagnosis of bronchiectasis is highly dependent on lung volume and more reliably diagnosed using outer airway diameter. Difference in bronchiectasis and AWT severity between the two cohorts increased with each airway generation. (orig.)

Standard practice for estimating the approximate residual circumferential stress in straight thin-walled tubing

CERN Document Server

American Society for Testing and Materials. Philadelphia

2007-01-01

1.1 A qualitative estimate of the residual circumferential stress in thin-walled tubing may be calculated from the change in outside diameter that occurs upon splitting a length of the tubing. This practice assumes a linear stress distribution through the tube wall thickness and will not provide an estimate of local stress distributions such as surface stresses. (Very high local residual stress gradients are common at the surface of metal tubing due to cold drawing, peening, grinding, etc.) The Hatfield and Thirkell formula, as later modified by Sachs and Espey, provides a simple method for calculating the approximate circumferential stress from the change in diameter of straight, thin-walled, metal tubing. 1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Improving nuclear regulation. Compilation of Nea regulatory guidance booklets

International Nuclear Information System (INIS)

2009-01-01

A common theme throughout the series of NEA regulatory guidance reports, or 'green booklets', is the premise that the fundamental objective of all nuclear safety regulatory bodies is to ensure that nuclear facilities are operated at all times and later decommissioned in an acceptably safe manner. In meeting this objective the regulator must keep in mind that it is the operator that has responsibility for safely operating a nuclear facility; the role of the regulator is to oversee the operator's activities as related to assuming that responsibility. For the first time, the full series of these reports have been brought together in one edition. As such, it is intended to serve as a knowledge management tool both for current regulators and the younger generation of nuclear experts entering the regulatory field. While the audience for this publication is primarily nuclear regulators, the information and ideas may also be of interest to nuclear operators, other nuclear industry organisations and the general public. (author)

The Atomic Energy Control Board's regulatory research and support program

International Nuclear Information System (INIS)

1988-04-01

The purpose of the Regulatory Research and Support Program is to augment and extend the capability of the Atomic Energy Control Board's (AECB) regulatory program beyond the capability of in-house resources. The overall objective of the program is to produce pertinent and independent scientific and other knowledge and expertise that will assist the AECB in making correct, timely and credible decisions on regulating the development, application and use of atomic energy. The objectives are achieved through contracted research, development, studies, consultant and other kinds of projects administered by the Research and Radiation Protection Branch (RRB) of the AECB

Structures of masonry walls in buildings of permanent ruin – causes of damage and methods of repairs

OpenAIRE

Bartosz Szostak

2017-01-01

Currently there is a lot of castles classified as objects of the permanent ruin. In according to conservation doctrine, it is needed to protect this objects and prevent further degradation. Usually one of the most destructed element in this type of object is masonry wall. In this article has been described selected types of the masonry walls of the permanent ruin, causes of their damages and repairs methods.

Structures of masonry walls in buildings of permanent ruin – causes of damage and methods of repairs

Directory of Open Access Journals (Sweden)

Bartosz Szostak

2017-12-01

Full Text Available Currently there is a lot of castles classified as objects of the permanent ruin. In according to conservation doctrine, it is needed to protect this objects and prevent further degradation. Usually one of the most destructed element in this type of object is masonry wall. In this article has been described selected types of the masonry walls of the permanent ruin, causes of their damages and repairs methods.

Reinforcement mechanism of multi-anchor wall with double wall facing

Science.gov (United States)

Suzuki, Kouta; Kobayashi, Makoto; Miura, Kinya; Konami, Takeharu; Hayashi, Taketo

2017-10-01

The reinforced soil wall has high seismic performance as generally known. However, the seismic behavior has not been clarified accurately yet, especially on multi-anchor wall with double wall facing. Indefinite behavior of reinforced soil wall during earthquake make us complicated in case with adopting to the abutment, because of arrangement of anchor plate as reinforcement often different according to the width of roads. In this study, a series of centrifuge model tests were carried out to investigate the reinforcement mechanism of multi anchor wall with double wall facing from the perspective of the vertical earth pressure. Several types of reinforce arrangement and rigid wall were applied in order to verify the arch function in the reinforced regions. The test results show unique behavior of vertical earth pressure, which was affected by arch action. All the vertical earth pressure placed behind facing panel, are larger than that of middle part between facing panel despite of friction between backfill and facing panel. Similar results were obtained in case using rigid wall. On the other hands, the vertical earth pressure, which were measured at the 3cm high from bottom of model container, shows larger than that of bottom. This results show the existence of arch action between double walls. In addition, it implies that the wall facing of such soil structure confined the backfill as pseudo wall, which is very reason that the multi anchor wall with double wall facing has high seismic performance.

Regulatory issues and assumptions associated with barriers in the vadose zone surrounding buried waste

International Nuclear Information System (INIS)

Siskind, B.; Heiser, J.

1993-02-01

One of the options for control of contaminant migration from buried waste sites is the construction of a subsurface barrier that consists of a wall of low permeability material. The barrier material should be compatible with soil and waste conditions specific to the site and have as low an effective diffusivity as is reasonably achievable to minimize or inhibit transport of moisture and contaminants. This report addresses the regulatory issues associated with the use of non-traditional organic polymer barriers as well as the use of soil-bentonite or cement-bentonite mixtures for such barriers, considering barriers constructed from these latter materials to be a regulatory baseline. The regulatory issues fall into two categories. The first category consists of issues associated with the acceptability of such barriers to the EPA as a method for achieving site or performanceimprovement. The second category encompasses those regulatory issues concerning health, safety and the environment which must be addressed regarding barrier installation and performance, especially if non-traditional materials are to be used

As to achieve regulatory action, regulatory approaches

International Nuclear Information System (INIS)

Cid, R.; Encinas, D.

2014-01-01

The achievement of the effectiveness in the performance of a nuclear regulatory body has been a permanent challenge in the recent history of nuclear regulation. In the post-Fukushima era this challenge is even more important. This article addresses the subject from two complementary points of view: the characteristics of an effective regulatory body and the regulatory approaches. This work is based on the most recent studies carried out by the Committee on Nuclear Regulatory Activities, CNRA (OECD/NEA), as well as on the experience of the Consejo de Seguridad Nuclear, CSN, the Spanish regulatory body. Rafael Cid is the representative of CSN in these project: Diego Encinas has participated in the study on regulatory approaches. (Author)

Dynamic behavior and functional integrity tests on RC shear walls

International Nuclear Information System (INIS)

Akino, Kinji; Nasuda, Toshiaki; Shibata, Akenori.

1991-01-01

A project consisting of seven subprojects has been conducted to study the dynamic behavior and functional integrity of reinforced concrete (RC) shear walls in reactor buildings. The objective of this project is to obtain the data to improve and prepare the seismic analysis code regarding the nonlinear structural behavior and integrity of reactor buildings during and after earthquakes. The project started in April, 1986, and will end in March, 1994. Seven subprojects are strain rate test, damping characteristic test, ultimate state response test and the verification test for the test of restoring force characteristics regarding dynamic restoring force characteristics and damping performance; the restoring force characteristic test on the shear walls with openings; and pull-out strength test and the test on air leakage through concrete cracks regarding the functional integrity. The objectives of respective subprojects, the test models and the interim results are reported. Three subprojects have been completed by March, 1990. The results of these projects will be used for the overall evaluation. The strain rate test showed that the ultimate strength of shear walls increased with strain rate. A formula for estimating air flow through the cracks in walls was given by the leakage test. (K.I.)

Regulatory control of maintenance activities in Argentine nuclear power plants

International Nuclear Information System (INIS)

Calvo, J.C.; Caruso, G.

2000-01-01

The main maintenance objective is to assure that the safety features of structures, components and systems of nuclear power plants are kept as designed. Therefore, there is a direct relationship between safety and maintenance. Owing to the above mentioned, maintenance activities are considered a relevant regulatory issue for the Argentine Nuclear Regulatory Authority (ARN). This paper describes the regulatory control to maintenance activities of Argentine nuclear power plants. It also addresses essential elements for maintenance control, routine inspections, special inspections during planned outages, audits and license conditions and requirements. (author)

SUBSTANTIATION OF DESIGN MEASURES TO INCREASE ENERGY EFFICIENCY OF EXTERIOR WALLS

Directory of Open Access Journals (Sweden)

Musorina Tat'yana Aleksandrovna

2017-11-01

Full Text Available Subject: multi-layer building envelope is the subject of the paper. Recently, in the context of energy conservation policies, the heat engineering requirements for enveloping structures of buildings and structures have significantly increased. At the same time, their moisture condition has a significant impact on the operational properties of materials of structures and on microclimate of rooms constrained by these structures. Research objectives: emphasize importance of the task of predicting the temperature and moisture condition of the walling at the stage of design and construction of building envelopes. In this paper, the temperature distributions in layered walls are analyzed. Materials and methods: to achieve the objectives, computational and experimental studies are conducted. By alternating (rearranging layers and preserving the thermal resistance of the wall on the whole, we find the optimal alternation of layers that minimizes deviation of the maximum wall temperature from the average temperature. Results: for the optimal location of layers in the wall’s structure, the moisture penetration into the wall is minimal or absent altogether. This is possible if the heat-insulating layer is mounted on the outer surface of the structure. Conclusions: the obtained results of computational and experimental studies allow us to verify appropriateness of accounting for alternation of layers in multilayer structures. These calculations proved that the higher the average temperature level, the more energy-efficient the structure will be.

Objective of the regulatory system for the physical protection of facilities and nuclear materials

International Nuclear Information System (INIS)

Polo, Rolando

1996-01-01

During the work that is developed in our country in order to have a regulatory system, recommendation on the issue have been considered. Such recommendation are gathered in the informative regulation 225 rev, 3 of the IAEA and the requirements are collected in the Informative Regulation 274 rev 1 of the IAEA, as well as the good national and international practices

Functional residual capacity increase during laparoscopic surgery with abdominal wall lift

Directory of Open Access Journals (Sweden)

Hiroshi Ueda

Full Text Available Abstract Background and objectives: The number of laparoscopic surgeries performed is increasing every year and in most cases the pneumoperitoneum method is used. One alternative is the abdominal wall lifting method and this study was undertaken to evaluate changes of functional residual capacity during the abdominal wall lift procedure. Methods: From January to April 2013, 20 patients underwent laparoscopic cholecystectomy at a single institution. All patients were anesthetized using propofol, remifentanil and rocuronium. FRC was measured automatically by Engstrom Carestation before the abdominal wall lift and again 15 minutes after the start of the procedure. Results: After abdominal wall lift, there was a significant increase in functional residual capacity values (before abdominal wall lift 1.48 × 103 mL, after abdominal wall lift 1.64 × 103 mL (p < 0.0001. No complications such as desaturation were observed in any patient during this study. Conclusions: Laparoscopic surgery with abdominal wall lift may be appropriate for patients who have risk factors such as obesity and respiratory disease.

The influence of wall permeability on laminar and turbulent flows : Theory and simulations

NARCIS (Netherlands)

Breugem, W.P.

2005-01-01

The study of flows over permeable walls is relevant to many applications. Examples are flows over and through porous river beds, vegetation, snow, heat exchangers of foam metal, and oil wells. The main objectives of this thesis are to gain insight in the influence of wall permeability on both

Phenomenology of wall-bounded Newtonian turbulence.

Science.gov (United States)

L'vov, Victor S; Pomyalov, Anna; Procaccia, Itamar; Zilitinkevich, Sergej S

2006-01-01

We construct a simple analytic model for wall-bounded turbulence, containing only four adjustable parameters. Two of these parameters are responsible for the viscous dissipation of the components of the Reynolds stress tensor. The other two parameters control the nonlinear relaxation of these objects. The model offers an analytic description of the profiles of the mean velocity and the correlation functions of velocity fluctuations in the entire boundary region, from the viscous sublayer, through the buffer layer, and further into the log-law turbulent region. In particular, the model predicts a very simple distribution of the turbulent kinetic energy in the log-law region between the velocity components: the streamwise component contains a half of the total energy whereas the wall-normal and cross-stream components contain a quarter each. In addition, the model predicts a very simple relation between the von Kármán slope k and the turbulent velocity in the log-law region v+ (in wall units): v+=6k. These predictions are in excellent agreement with direct numerical simulation data and with recent laboratory experiments.

Understanding and Exploiting Wind Tunnels with Porous Flexible Walls for Aerodynamic Measurement

OpenAIRE

Brown, Kenneth Alexander

2016-01-01

The aerodynamic behavior of wind tunnels with porous, flexible walls formed from tensioned Kevlar has been characterized and new measurement techniques in such wind tunnels explored. The objective is to bring the aerodynamic capabilities of so-called Kevlar-wall test sections in-line with those of traditional solid-wall test sections. The primary facility used for this purpose is the 1.85-m by 1.85-m Stability Wind Tunnel at Virginia Tech, and supporting data is provided by the 2-m by 2-m L...

Expansible apparatus for removing the surface layer from a concrete object

International Nuclear Information System (INIS)

Allen, C.H.

1979-01-01

A method and apparatus for removing the surface layer from a concrete object are described. The method consists of providing a hole having a circular wall in the surface layer of the object, the hole being at least as deep as the thickness of the surface layer to be removed, and applying an outward wedging pressure on the wall of the hole sufficient to spall the surface layer around the hole. By the proper spacing of an appropriate number of holes, it is possible to remove the entire surface layer. The apparatus consists of an elongated tubular-shaped body having a relatively short handle with a solid wall at one end. The wall of the remainder of the body contains a plurality of evenly spaced longitudinal cuts to form a relatively long expandable section. The outer end of the expandable section has an expandable, wedge-shaped spalling edge extending from the outer surface of the wall, perpendicular to the longitudinal axis of the body, and expanding means in the body for outwardly expanding the expandable section and forcing the spalling edge into the wall of a hole with sufficient outward pressure to spall away the surface layer of concrete. The method and apparatus are particularly suitable for removing surface layers of concrete which are radioactively contaminated

Regulatory research and support program for 1993/1994 - project descriptions

International Nuclear Information System (INIS)

1993-01-01

The Regulatory Research and Support Program (RSP) is intended to augment and extend the Atomic Energy Control Board's regulatory program beyond the capability of in-house resources. The overall objective of the research and support program is to produce pertinent and independent information that will assist the Board and its staff in making sound, timely and credible decisions on regulating nuclear facilities and materials. The program is divided into nine main areas of research (mission objects) covering the safety of nuclear facilities, radioactive waste management, health physics, physical security, the development of regulatory processes, and special services. In addition, for the first time in this year's program, sub-programs (collections of related projects) have been organized in some areas of study; these sub-programs may cut across several mission objects. More sub-programs will be introduced in future years. A total of 96 projects are planned for 1993/94, including a number which are ongoing from the previous fiscal year. Projects that are held in reserve in case funding becomes available are also listed and provisionally ranked. The spending estimates for the RSP were calculated on the basis of an expected budget of $3.85 M

Regulatory research and support program for 1993/1994 - project descriptions

Energy Technology Data Exchange (ETDEWEB)

NONE

1993-03-01

The Regulatory Research and Support Program (RSP) is intended to augment and extend the Atomic Energy Control Board`s regulatory program beyond the capability of in-house resources. The overall objective of the research and support program is to produce pertinent and independent information that will assist the Board and its staff in making sound, timely and credible decisions on regulating nuclear facilities and materials. The program is divided into nine main areas of research (mission objects) covering the safety of nuclear facilities, radioactive waste management, health physics, physical security, the development of regulatory processes, and special services. In addition, for the first time in this year`s program, sub-programs (collections of related projects) have been organized in some areas of study; these sub-programs may cut across several mission objects. More sub-programs will be introduced in future years. A total of 96 projects are planned for 1993/94, including a number which are ongoing from the previous fiscal year. Projects that are held in reserve in case funding becomes available are also listed and provisionally ranked. The spending estimates for the RSP were calculated on the basis of an expected budget of $3.85 M.

Nuclear Fuel Cycle Objectives

International Nuclear Information System (INIS)

2013-01-01

One of the IAEA's statutory objectives is to 'seek to accelerate and enlarge the contribution of atomic energy to peace, health and prosperity throughout the world'. One way this objective is achieved is through the publication of a range of technical series. Two of these are the IAEA Nuclear Energy Series and the IAEA Safety Standards Series. According to Article III.A.6 of the IAEA Statute, the safety standards establish 'standards of safety for protection of health and minimization of danger to life and property'. The safety standards include the Safety Fundamentals, Safety Requirements and Safety Guides. These standards are written primarily in a regulatory style, and are binding on the IAEA for its own programmes. The principal users are the regulatory bodies in member States and other national authorities. The IAEA Nuclear Energy Series comprises reports designed to encourage and assist R and D on, and application of, nuclear energy for peaceful uses. This includes practical examples to be used by owners and operators of utilities in member States, implementing organizations, academia and government officials, among others. This information is presented in guides, reports on technology status and advances, and best practices for peaceful uses of nuclear energy based on inputs from international experts. The IAEA Nuclear Energy Series complements the IAEA Safety Standards Series. The Nuclear Energy Basic Principles is the highest level publication in the IAEA Nuclear Energy Series, and describes the rationale and vision for the peaceful uses of nuclear energy. It presents eight Basic Principles on which nuclear energy systems should be based to fulfil nuclear energy's potential to help meet growing global energy needs. The Nuclear Energy Series Objectives are the second level publications. They describe what needs to be considered and the specific goals to be achieved at different stages of implementation, all of which are consistent with the Basic Principles

Wind tunnels with adapted walls for reducing wall interference

Science.gov (United States)

Ganzer, U.

1979-01-01

The basic principle of adaptable wind tunnel walls is explained. First results of an investigation carried out at the Aero-Space Institute of Berlin Technical University are presented for two dimensional flexible walls and a NACA 0012 airfoil. With five examples exhibiting very different flow conditions it is demonstrated that it is possible to reduce wall interference and to avoid blockage at transonic speeds by wall adaptation.

Inverse measurement of wall pressure field in flexible-wall wind tunnels using global wall deformation data

Science.gov (United States)

Brown, Kenneth; Brown, Julian; Patil, Mayuresh; Devenport, William

2018-02-01

The Kevlar-wall anechoic wind tunnel offers great value to the aeroacoustics research community, affording the capability to make simultaneous aeroacoustic and aerodynamic measurements. While the aeroacoustic potential of the Kevlar-wall test section is already being leveraged, the aerodynamic capability of these test sections is still to be fully realized. The flexibility of the Kevlar walls suggests the possibility that the internal test section flow may be characterized by precisely measuring small deflections of the flexible walls. Treating the Kevlar fabric walls as tensioned membranes with known pre-tension and material properties, an inverse stress problem arises where the pressure distribution over the wall is sought as a function of the measured wall deflection. Experimental wall deformations produced by the wind loading of an airfoil model are measured using digital image correlation and subsequently projected onto polynomial basis functions which have been formulated to mitigate the impact of measurement noise based on a finite-element study. Inserting analytic derivatives of the basis functions into the equilibrium relations for a membrane, full-field pressure distributions across the Kevlar walls are computed. These inversely calculated pressures, after being validated against an independent measurement technique, can then be integrated along the length of the test section to give the sectional lift of the airfoil. Notably, these first-time results are achieved with a non-contact technique and in an anechoic environment.

First Wall, Blanket, Shield Engineering Technology Program

International Nuclear Information System (INIS)

Nygren, R.E.

1982-01-01

The First Wall/Blanket/Shield Engineering Technology Program sponsored by the Office of Fusion Energy of DOE has the overall objective of providing engineering data that will define performance parameters for nuclear systems in advanced fusion reactors. The program comprises testing and the development of computational tools in four areas: (1) thermomechanical and thermal-hydraulic performance of first-wall component facsimiles with emphasis on surface heat loads; (2) thermomechanical and thermal-hydraulic performance of blanket and shield component facsimiles with emphasis on bulk heating; (3) electromagnetic effects in first wall, blanket, and shield component facsimiles with emphasis on transient field penetration and eddy-current effects; (4) assembly, maintenance and repair with emphasis on remote-handling techniques. This paper will focus on elements 2 and 4 above and, in keeping with the conference participation from both fusion and fission programs, will emphasize potential interfaces between fusion technology and experience in the fission industry

Safety Culture Implementation in Indonesian Nuclear Energy Regulatory Agency (BAPETEN)

International Nuclear Information System (INIS)

Nurwidi Astuti, Y.H.; Dewanto, P.

2016-01-01

The Indonesia Nuclear Energy Act no. 10 of 1997 clearly stated that Nuclear Energy Regulatory Agency (BAPETEN) is the Nuclear Regulatory Body. This is the legal basis of BAPETEN to perform regulatory functions on the use of nuclear energy in Indonesia, including regulation, authorisation, inspection and enforcement. The Independent regulatory functions are stipulated in Article 4 and Article 14 of the Nuclear Energy Act no. 10 (1997) which require the government to establish regulatory body that is reporting directly to the president and has responsibility to control of the use of nuclear energy. BAPETEN has been start fully its functioning on January 4, 1999. In it roles as a regulatory body, the main aspect that continues and always to be developed is the safety culture. One of the objectives of regulatory functions is “to increase legal awareness of nuclear energy of the user to develop safety culture” (Article 15, point d), while in the elucidation of article 15 it is stipulated that “safety culture is that of characteristics and attitudes in organizations and individual that emphasise the importance of safety”.

Preparation of safety and regulatory document for BARC Facilities

International Nuclear Information System (INIS)

Prasad, S.S.; Jayarajan, K.

2017-01-01

In India, the necessary codes and safety guidelines for achieving the safety objectives are provided by the Atomic Energy Regulatory Board (AERB), which are in conformity with the principles of radiation protection as formulated by the International Council of Radiation Protection (ICRP) and International Atomic Energy Agency (IAEA). The same is followed by BARC Safety Council (BSC), which is the regulatory body for the BARC facilities. In addition to all types of fuel cycle facilities, BSC regulates safety of many types of conventional facilities. Many such types of facilities and projects are not under the regulatory purview of AERB. Therefore, the Council has also initiated a programme for development and publication of safety documents for installations in BARC in the fields/ topics yet not addressed by IAEA or AERB. This makes the task pioneering, as some of the areas taken up for defining the regulatory requirements are new, where standard regulatory documents are not available

Diagnosis of bronchiectasis and airway wall thickening in children with cystic fibrosis. Objective airway-artery quantification

Energy Technology Data Exchange (ETDEWEB)

Kuo, Wieying; Tiddens, Harm A.W.M. [Erasmus MC - Sophia Children' s Hospital, Department of Pediatric Pulmonology and Allergology, Rotterdam (Netherlands); Erasmus MC, Department of Radiology, Rotterdam (Netherlands); Bruijne, Marleen de [Erasmus MC, Biomedical Imaging Group Rotterdam, Departments of Medical Informatics and Radiology, Rotterdam (Netherlands); University of Copenhagen, Department of Computer Science, Copenhagen (Denmark); Petersen, Jens [University of Copenhagen, Department of Computer Science, Copenhagen (Denmark); Nasserinejad, Kazem [Erasmus MC Cancer Institute, HOVON Data Center, Clinical Trial Center, Rotterdam (Netherlands); Erasmus MC, Department of Biostatistics, Rotterdam (Netherlands); Ozturk, Hadiye [Erasmus MC - Sophia Children' s Hospital, Department of Pediatric Pulmonology and Allergology, Rotterdam (Netherlands); Chen, Yong [General Hospital of Ningxia Medical University, Department of Radiology, Yinchuan (China); Perez-Rovira, Adria [Erasmus MC - Sophia Children' s Hospital, Department of Pediatric Pulmonology and Allergology, Rotterdam (Netherlands); Erasmus MC, Biomedical Imaging Group Rotterdam, Departments of Medical Informatics and Radiology, Rotterdam (Netherlands)

2017-11-15

To quantify airway and artery (AA)-dimensions in cystic fibrosis (CF) and control patients for objective CT diagnosis of bronchiectasis and airway wall thickness (AWT). Spirometer-guided inspiratory and expiratory CTs of 11 CF and 12 control patients were collected retrospectively. Airway pathways were annotated semi-automatically to reconstruct three-dimensional bronchial trees. All visible AA-pairs were measured perpendicular to the airway axis. Inner, outer and AWT (outer-inner) diameter were divided by the adjacent artery diameter to compute A{sub in}A-, A{sub out}A- and A{sub WT}A-ratios. AA-ratios were predicted using mixed-effects models including disease status, lung volume, gender, height and age as covariates. Demographics did not differ significantly between cohorts. Mean AA-pairs CF: 299 inspiratory; 82 expiratory. Controls: 131 inspiratory; 58 expiratory. All ratios were significantly larger in inspiratory compared to expiratory CTs for both groups (p<0.001). A{sub out}A- and A{sub WT}A-ratios were larger in CF than in controls, independent of lung volume (p<0.01). Difference of A{sub out}A- and A{sub WT}A-ratios between patients with CF and controls increased significantly for every following airway generation (p<0.001). Diagnosis of bronchiectasis is highly dependent on lung volume and more reliably diagnosed using outer airway diameter. Difference in bronchiectasis and AWT severity between the two cohorts increased with each airway generation. (orig.)

Geosynthetic wall performance : facing pressure and deformation : final report.

Science.gov (United States)

2017-02-01

The objective of the study was to validate the performance of blocked-faced Geosynthetic Reinforced Soil (GRS) wall and to validate the Colorado Department of Transportations (CDOT) decision to waive the positive block connection for closely-space...

Creating a safety culture in the regulatory authority: The Cuban experience

International Nuclear Information System (INIS)

Ferro Fernandez, R.; Guillen Campos, A.

2002-01-01

The Cuban regulatory authority has been working during several years for the fostering and development of a high Safety Culture level in nuclear activities in the country. As starting point to achieve this objective the assessment of the Safety Culture level in the regulatory authority performance was considered an important issue. For this purpose a preliminary diagnosis was carried out by means of a national survey that allowed identifying some areas of the regulatory activity that required improvements in order to achieve a higher Safety Culture and to immediately implement appropriate actions. Two of the most important actions undertaken were: the statement of the regulatory authority Safety Policy which governs and determines the performance of this organization and its staff and also the implementation of a new interaction practice at top level between the regulatory authority and the utilities of the nuclear sector through the Annual Regulatory Conference. The present paper summarizes these two introduced practices into the Cuban regulatory activity. (author)

Manipulation of near-wall turbulence by surface slip and permeability

Science.gov (United States)

Gómez-de-Segura, G.; Fairhall, C. T.; MacDonald, M.; Chung, D.; García-Mayoral, R.

2018-04-01

We study the effect on near-wall turbulence of tangential slip and wall-normal transpiration, typically produced by textured surfaces and other surface manipulations. For this, we conduct direct numerical simulations (DNSs) with different virtual origins for the different velocity components. The different origins result in a relative wall-normal displacement of the near-wall, quasi-streamwise vortices with respect to the mean flow, which in turn produces a change in drag. The objective of this work is to extend the existing understanding on how these virtual origins affect the flow. In the literature, the virtual origins for the tangential velocities are typically characterised by slip boundary conditions, while the wall-normal velocity is assumed to be zero at the boundary plane. Here we explore different techniques to define and implement the three virtual origins, with special emphasis on the wall-normal one. We investigate impedance conditions relating the wall-normal velocity to the pressure, and linear relations between the velocity components and their wall-normal gradients, as is typically done to impose slip conditions. These models are first tested to represent a smooth wall below the boundary plane, with all virtual origins equal, and later for different tangential and wall-normal origins. Our results confirm that the change in drag is determined by the offset between the origins perceived by mean flow and the quasi-streamwise vortices or, more generally, the near-wall turbulent cycle. The origin for the latter, however, is not set by the spanwise virtual origin alone, as previously proposed, but by a combination of the spanwise and wall-normal origins, and mainly determined by the shallowest of the two. These observations allow us to extend the existing expression to predict the change in drag, accounting for the wall-normal effect when the transpiration is not negligible.

Techniques of analyzing the impacts of certain electric-utility ratemaking and regulatory-policy concepts. Bibliography

Energy Technology Data Exchange (ETDEWEB)

None

1980-08-01

This bibliography provides documentation for use by state public utility commissions and major nonregulated utilities in evaluating the applicability of a wide range of electric utility rate design and regulatory concepts in light of certain regulatory objectives. Part I, Utility Regulatory Objectives, contains 2084 citations on conservation of energy and capital; efficient use of facilities and resources; and equitable rates to electricity consumers. Part II, Rate Design Concepts, contains 1238 citations on time-of-day rates; seasonally-varying rates; cost-of-service rates; interruptible rates (including the accompanying use of load management techniques); declining block rates; and lifeline rates. Part III, Regulatory Concepts, contains 1282 references on restrictions on master metering; procedures for review of automatic adjustment clauses; prohibitions of rate or regulatory discrimination against solar, wind, or other small energy systems; treatment of advertising expenses; and procedures to protect ratepayers from abrupt termination of service.

Basic elements of a regulatory programme for radiation safety

International Nuclear Information System (INIS)

Bilbao, A.A.

2000-01-01

In this lecture the objectives of IAEA TECDOC 1067: Organization and implementation of a national regulatory infrastructure governing protection against ionizing radiation and the safety of sources (1999) is presented

Radioactive Waste Management Objectives

International Nuclear Information System (INIS)

2011-01-01

One of the IAEA's statutory objectives is to 'seek to accelerate and enlarge the contribution of atomic energy to peace, health and prosperity throughout the world'. One way it achieves this objective is to issue publications in various series. Two of these series are the IAEA Nuclear Energy Series and the IAEA Safety Standards Series. According to Article III, paragraph A.6, of the IAEA Statute, the IAEA safety standards establish 'standards of safety for protection of health and minimization of danger to life and property.' The safety standards include the Safety Fundamentals, Safety Requirements and Safety Guides. These standards are primarily written in a regulatory style, and are binding on the IAEA for its own activities. The principal users are Member State regulatory bodies and other national authorities. The IAEA Nuclear Energy Series consists of reports designed to encourage and assist research on, and development and practical application of, nuclear energy for peaceful uses. This includes practical examples to be used by owners and operators of utilities in Member States, implementing organizations, academia and politicians, among others. The information is presented in guides, reports on the status of technology and advances, and best practices for peaceful uses of nuclear energy based on inputs from international experts. The series complements the IAEA's safety standards, and provides detailed guidance, experience, good practices and examples on the five areas covered in the IAEA Nuclear Energy Series. The Nuclear Energy Basic Principles is the highest level publication in the IAEA Nuclear Energy Series and describes the rationale and vision for the peaceful uses of nuclear energy. It presents eight Basic Principles on which nuclear energy systems should be based to fulfil nuclear energy's potential to help meet growing global energy needs. The Nuclear Energy Series Objectives are the second level publications. They describe what needs to be

FEM analysis of impact of external objects to pipelines

Energy Technology Data Exchange (ETDEWEB)

Gracie, Robert; Konuk, Ibrahim [Geological Survey of Canada, Ottawa, ON (Canada)]. E-mail: ikonuk@NRCan.gc.ca; Fredj, Abdelfettah [BMT Fleet Technology Limited, Ottawa, ON (Canada)

2003-07-01

One of the most common hazards to pipelines is impact of external objects. Earth moving machinery, farm equipment or bullets can dent or fail land pipelines. External objects such as anchors, fishing gear, ice can damage offshore pipelines. This paper develops an FEM model to simulate the impact process and presents investigations using the FEM model to determine the influence of the geometry and velocity of the impacting object and also will study the influence of the pipe diameter, wall thickness, and concrete thickness along with internal pressure. The FEM model is developed by using LS-DYNA explicit FEM software utilizing shell and solid elements. The model allows damage and removal of the concrete and corrosion coating elements during impact. Parametric studies will be presented relating the dent size to pipe diameter, wall thickness and concrete thickness, internal pipe pressure, and impacting object geometry. The primary objective of this paper is to develop and present the FEM model. The model can be applied to both offshore and land pipeline problems. Some examples are used to illustrate how the model can be applied to real life problems. A future paper will present more detailed parametric studies. (author)

Domain wall solitons and Hopf algebraic translational symmetries in noncommutative field theories

International Nuclear Information System (INIS)

Sasai, Yuya; Sasakura, Naoki

2008-01-01

Domain wall solitons are the simplest topological objects in field theories. The conventional translational symmetry in a field theory is the generator of a one-parameter family of domain wall solutions, and induces a massless moduli field which propagates along a domain wall. We study similar issues in braided noncommutative field theories possessing Hopf algebraic translational symmetries. As a concrete example, we discuss a domain wall soliton in the scalar φ 4 braided noncommutative field theory in Lie-algebraic noncommutative space-time, [x i ,x j ]=2iκε ijk x k (i,j,k=1,2,3), which has a Hopf algebraic translational symmetry. We first discuss the existence of a domain wall soliton in view of Derrick's theorem, and construct explicitly a one-parameter family of solutions in perturbation of the noncommutativity parameter κ. We then find the massless moduli field which propagates on the domain wall soliton. We further extend our analysis to the general Hopf algebraic translational symmetry

Data fusion of ultrasound and GPR signals for analysis of historic walls

International Nuclear Information System (INIS)

Salazar, A; Gosalbez, J; Safont, G; Vergara, L

2012-01-01

This paper presents an application of ultrasounds and ground-penetrating radar (GPR) for analysis of historic walls. The objectives are to characterize the deformation of a historic wall under different levels of load weights and to obtain an enhanced image of the wall. A new method that fuses data from ultrasound and GPR traces is proposed which is based on order statistics digital filters. Application results are presented for non destructive testing (NDT) of two replicates of historic ashlars' masonry walls: the first one homogeneous and the second one containing controlled defects such as cracks and nooks. The walls are measured separately using ultrasounds and GPR at different load steps. Time and frequency parameters extracted from the signals and different B-Scans for each of the NDT techniques are obtained. After this, a new fused representation is obtained, which results demonstrate the improvement of characterization and defect detection in historic walls using data fusion.

Well device for removing small objects

Energy Technology Data Exchange (ETDEWEB)

Rastorguyev, M.A.; Mubashirov, S.G.; Nikolayev, G.I.; Prokopov, O.I.

1982-01-01

A well device is proposed for removing small objects. It contains a hollow housing with worm and crown installed with the possibility of rotation in relation to the housing. It is distinguished by the fact that in order to increase reliability of holding the trapped objects, on the lower end of the housing there is a disc which forms with the housing a chamber for the trapped objects. In this case the disc is made with sector slit, one of whose sidewalls is superposed with the worm blade rigidly connected to the disc, while along the other side wall a plate is vertically attached.

Avoidance goal pursuit depletes self-regulatory resources

NARCIS (Netherlands)

Oertig, D.; Schüler, J.; Schnelle, J.; Brandstätter, V.; Roskes, M.; Elliot, A.J.

2013-01-01

Objective: Research on the strength model of self-regulation is burgeoning, but little empirical work has focused on the link between distinct types of daily goal pursuit and the depletion of self-regulatory resources. Here we conducted two studies on the link between avoidance goals and resource

Avoidance goal pursuit depletes self-regulatory resources

NARCIS (Netherlands)

Oertig, Daniela; Schüler, Julia; Schnelle, Jessica; Brandstätter, Veronika; Roskes, Marieke; Elliot, Andrew J.

Objective: Research on the strength model of self-regulation is burgeoning, but little empirical work has focused on the link between distinct types of daily goal pursuit and the depletion of self-regulatory resources. The authors conducted two studies on the link between avoidance goals and

The nuclear regulatory process in Canada experience and possible future direction

International Nuclear Information System (INIS)

Sainsbury, J.D.

1987-01-01

The underlying principle in the Canadian licensing process is that the licensee (owner/operatopr) bears the responsibility for safety while the regulatory authority sets safety objectives and audits their achievement. As a consequence, Canadian Regulatory Requirements emphasize numerical safety goals, and minimize specific design or operational rules. This paper traces the evolution of this approach, and indicates direction for the future. (author)

Wall-based identification of coherent structures in wall-bounded turbulence

Science.gov (United States)

Sanmiguel Vila, C.; Flores, O.

2018-04-01

During the last decades, a number of reduced order models based on coherent structures have been proposed to describe wall-bounded turbulence. Many of these models emphasize the importance of coherent wall-normal velocity eddies (ν-eddies), which drive the generation of the very long streamwise velocity structures observed in the logarithmic and outer region. In order to use these models to improve our ability to control wall-bounded turbulence in realistic applications, these ν-eddies need to be identified from the wall in a non-intrusive way. In this paper, the possibility of using the pressure signal at the wall to identify these ν-eddies is explored, analyzing the cross-correlation between the wall-normal velocity component and the pressure fluctuations at the wall in a DNS of a turbulent channel flow at Reτ = 939. The results show that the cross-correlation has a region of negative correlation upstream, and a region of positive correlation backwards. In the spanwise direction the correlation decays monotonously, except very close to the wall where a change of sign of the correlation coefficient is observed. Moreover, filtering the pressure fluctuations at the wall in space results in an increase of the region where the cross-correlation is strong, both for the positively and the negatively correlated regions. The use of a time filter for the pressure fluctuations at the wall yields different results, displacing the regions of strong correlation without changing much their sizes. The results suggest that space-filtering the pressure at the wall is a feasible way to identify ν-eddies of different sizes, which could be used to trigger turbulent control strategies.

Role of the Regulatory Body in Implementing Defence in Depth in Nuclear Installations - Regulatory Oversight in Egypt

Energy Technology Data Exchange (ETDEWEB)

El-Sheikh, B. M., E-mail: badawymel@yahoo.com [Egyptian Nuclear and Radiological Regulatory Authority Cairo (Egypt)

2014-10-15

The fundamental objective of all nuclear safety regulatory bodies is to ensure that nuclear facilities are operated at all times in an acceptably safe manner including the safe conduct of decommissioning activities. Defence in depth is recognized as one of the fundamental safety principles that underlie the safety of nuclear power plants. Defence in depth is implemented to provide a graded protection against a wide variety of transients, incidents and accidents, including equipment failures and human errors within nuclear power plants and events initiated outside plants. The Regulator Body plays an important role in implementing defence in depth in nuclear installations in the context of a clear allocation of responsibilities with an operating organization. This role starting with setting safety objectives and by its own independent review and technical assessment of the safety justifications provided by the operating organization in addition to safety culture investigating within relevant organizations. This paper briefly reviews this role in normal operation and post accidents, and its effects on overall nuclear safety in nuclear installations with reference to Egyptian regulatory oversight. (author)

INTOR first wall/blanket/shield activity

International Nuclear Information System (INIS)

Gohar, Y.; Billone, M.C.; Cha, Y.S.; Finn, P.A.; Hassanein, A.M.; Liu, Y.Y.; Majumdar, S.; Picologlou, B.F.; Smith, D.L.

1986-01-01

The main emphasis of the INTOR first wall/blanket/shield (FWBS) during this period has been upon the tritium breeding issues. The objective is to develop a FWBS concept which produces the tritium requirement for INTOR operation and uses a small fraction of the first wall surface area. The FWBS is constrained by the dimensions of the reference design and the protection criteria required for different reactor components. The blanket extrapolation to commercial power reactor conditions and the proper temperature for power extraction have been sacrificed to achieve the highest possible local tritium breeding ratio (TBR). In addition, several other factors that have been considered in the blanket survey study include safety, reliability, lifetime fluence, number of burn cycles, simplicity, cost, and development issues. The implications of different tritium supply scenarios were discussed from the cost and availability for INTOR conditions. A wide variety of blanket options was explored in a preliminary way to determine feasibility and to see if they can satisfy the INTOR conditions. This survey and related issues are summarized in this report. Also discussed are material design requirements, thermal hydraulic considerations, structure analyses, tritium permeation through the first wall into the coolant, and tritium inventory

Wall Shear Stress, Wall Pressure and Near Wall Velocity Field Relationships in a Whirling Annular Seal

Science.gov (United States)

Morrison, Gerald L.; Winslow, Robert B.; Thames, H. Davis, III

1996-01-01

The mean and phase averaged pressure and wall shear stress distributions were measured on the stator wall of a 50% eccentric annular seal which was whirling in a circular orbit at the same speed as the shaft rotation. The shear stresses were measured using flush mounted hot-film probes. Four different operating conditions were considered consisting of Reynolds numbers of 12,000 and 24,000 and Taylor numbers of 3,300 and 6,600. At each of the operating conditions the axial distribution (from Z/L = -0.2 to 1.2) of the mean pressure, shear stress magnitude, and shear stress direction on the stator wall were measured. Also measured were the phase averaged pressure and shear stress. These data were combined to calculate the force distributions along the seal length. Integration of the force distributions result in the net forces and moments generated by the pressure and shear stresses. The flow field inside the seal operating at a Reynolds number of 24,000 and a Taylor number of 6,600 has been measured using a 3-D laser Doppler anemometer system. Phase averaged wall pressure and wall shear stress are presented along with phase averaged mean velocity and turbulence kinetic energy distributions located 0.16c from the stator wall where c is the seal clearance. The relationships between the velocity, turbulence, wall pressure and wall shear stress are very complex and do not follow simple bulk flow predictions.

Bacterial cell wall preservation during organic matter diagenesis in sediments off Peru

DEFF Research Database (Denmark)

Lomstein, Bente Aagaard; Niggemann, Jutta; Jørgensen, Bo Barker

BACTERIAL CELL WALL PRESERVATION DURING ORGANIC MATTER DIAGENESIS IN SEDIMENTS OFF PERU The spatial distribution of total hydrolysable amino acids, total hydrolysable amino sugars and amino acid enantiomers (D- and L-forms) were investigated in surface sediments at 20 stations in the Peru margin: 9......°45 S - 13º32 S. The objective of this study was to assess the preservation of bacterial cell walls during diagenesis of organic matter. Bacterial cell walls were traced by analysis of biomarkers uniquely produced by bacteria (D-amino acids and muramic acid). The diagenetic status of the sediments......:00 Presentation is given by student: No...

Nuclear Energy General Objectives

International Nuclear Information System (INIS)

2011-01-01

One of the IAEA's statutory objectives is to 'seek to accelerate and enlarge the contribution of atomic energy to peace, health and prosperity throughout the world'. One way it achieves this objective is to issue publications in various series. Two of these series are the IAEA Nuclear Energy Series and the IAEA Safety Standards Series. According to Article III, paragraph A.6, of the IAEA Statute, the IAEA safety standards establish 'standards of safety for protection of health and minimization of danger to life and property.' The safety standards include the Safety Fundamentals, Safety Requirements and Safety Guides. These standards are primarily written in a regulatory style, and are binding on the IAEA for its own activities. The principal users are Member State regulatory bodies and other national authorities. The IAEA Nuclear Energy Series consists of reports designed to encourage and assist research on, and development and practical application of, nuclear energy for peaceful uses. This includes practical examples to be used by owners and operators of utilities in Member States, implementing organizations, academia and politicians, among others. The information is presented in guides, reports on the status of technology and advances, and best practices for peaceful uses of nuclear energy based on inputs from international experts. The series complements the IAEA's safety standards, and provides detailed guidance, experience, good practices and examples on the five areas covered in the IAEA Nuclear Energy Series. The Nuclear Energy Basic Principles is the highest level publication in the IAEA Nuclear Energy Series and describes the rationale and vision for the peaceful uses of nuclear energy. It presents eight Basic Principles on which nuclear energy systems should be based to fulfil nuclear energy's potential to help meet growing global energy needs. The Nuclear Energy Series Objectives are the second level publications. They describe what needs to be

Regulatory practices and safety standards for nuclear power plants

International Nuclear Information System (INIS)

1989-01-01

The International Symposium on Regulatory Practices and Safety Standards for Nuclear Power Plants was jointly organized by the International Atomic Energy Agency (IAEA), for Nuclear Energy Agency of the OECD and the Government of the Federal Republic of Germany with the objective of providing an international forum for the exchange of information on regulatory practices and safety standards for nuclear power plants. The Symposium was held in Munich, Federal Republic of Germany, from 7 to 10 November 1988. It was attended by 201 experts from some 32 Member States and 4 international organizations. Fifty-one papers from 19 Member States and 2 international organizations were presented and discussed in 5 technical sessions covering the following subjects: National Regulatory Practices and Safety Standards (14 papers); Implementation of Regulatory Practices - Technical Issues (8 papers); Implementation of Regulatory Practices - Operational Aspects (8 papers); Developments and Trends in Safety Standards and Practices (11 papers); International Aspects (10 papers). A separate abstract was prepared for each of these papers. Refs, figs and tabs

Electrical resisitivity of mechancially stablized earth wall backfill

Science.gov (United States)

Snapp, Michael; Tucker-Kulesza, Stacey; Koehn, Weston

2017-06-01

Mechanically stabilized earth (MSE) retaining walls utilized in transportation projects are typically backfilled with coarse aggregate. One of the current testing procedures to select backfill material for construction of MSE walls is the American Association of State Highway and Transportation Officials standard T 288: ;Standard Method of Test for Determining Minimum Laboratory Soil Resistivity.; T 288 is designed to test a soil sample's electrical resistivity which correlates to its corrosive potential. The test is run on soil material passing the No. 10 sieve and believed to be inappropriate for coarse aggregate. Therefore, researchers have proposed new methods to measure the electrical resistivity of coarse aggregate samples in the laboratory. There is a need to verify that the proposed methods yield results representative of the in situ conditions; however, no in situ measurement of the electrical resistivity of MSE wall backfill is established. Electrical resistivity tomography (ERT) provides a two-dimensional (2D) profile of the bulk resistivity of backfill material in situ. The objective of this study was to characterize bulk resistivity of in-place MSE wall backfill aggregate using ERT. Five MSE walls were tested via ERT to determine the bulk resistivity of the backfill. Three of the walls were reinforced with polymeric geogrid, one wall was reinforced with metallic strips, and one wall was a gravity retaining wall with no reinforcement. Variability of the measured resistivity distribution within the backfill may be a result of non-uniform particle sizes, thoroughness of compaction, and the presence of water. A quantitative post processing algorithm was developed to calculate mean bulk resistivity of in-situ backfill. Recommendations of the study were that the ERT data be used to verify proposed testing methods for coarse aggregate that are designed to yield data representative of in situ conditions. A preliminary analysis suggests that ERT may be utilized

Ambiguous walls

DEFF Research Database (Denmark)

Mody, Astrid

2012-01-01

The introduction of Light Emitting Diodes (LEDs) in the built environment has encouraged myriad applications, often embedded in surfaces as an integrated part of the architecture. Thus the wall as responsive luminous skin is becoming, if not common, at least familiar. Taking into account how walls...... have encouraged architectural thinking of enclosure, materiality, construction and inhabitation in architectural history, the paper’s aim is to define new directions for the integration of LEDs in walls, challenging the thinking of inhabitation and program. This paper introduces the notion...... of “ambiguous walls” as a more “critical” approach to design [1]. The concept of ambiguous walls refers to the diffuse status a lumious and possibly responsive wall will have. Instead of confining it can open up. Instead of having a static appearance, it becomes a context over time. Instead of being hard...

Regulatory inspection of nuclear power plants in NEA member countries

International Nuclear Information System (INIS)

Gronow, W.S.; Ilani, O.

1977-01-01

The increasing use of nuclear power and public interest in the safety controls led to the proposal by the sub-Committe on Licensing of the NEA Committee on the Safety of Nuclear Installations for a specialist meeting on regulatory inspection practices. This report which was prepared at the request of the sub-Committee to assist in the exchange of views and experience at the meeting reviews the response to a questionnaire on the systems employed, the scope and objectives and the effort involved in regulatory inspection throughout all stages of the life of a nuclear power plant. Other aspects of regulatory inspection activities are discussed including documentation, procedures for changes in technical specification and modifications to plant, powers and duties of regulatory inspection personnel and actions to be taken in the event of an accident or emergency. The report concludes with some comments on those aspects of regulatory inspection practices where further information and an exchange of experience might prove to be beneficial to Member countries. (author)

Technical Status Report of the Regulatory Assistance Project: October 2001-February 2003

Energy Technology Data Exchange (ETDEWEB)

2003-08-01

This report details the work undertaken from October 2001 to February 2003 by the Regulatory Assistance Project under subcontract to the National Renewable Energy Laboratory. The objectives of this work were to develop regulatory policy options that would reduce the institutional and infrastructure barriers to full-value deployment of distributed power systems. Specific tasks included leading technical workshops on removing or overcoming regulatory barriers to distributed resources for state utility regulators and developing a draft model rule on emission performance standards for distributed generation.

Search for domain wall dark matter with atomic clocks on board global positioning system satellites.

Science.gov (United States)

Roberts, Benjamin M; Blewitt, Geoffrey; Dailey, Conner; Murphy, Mac; Pospelov, Maxim; Rollings, Alex; Sherman, Jeff; Williams, Wyatt; Derevianko, Andrei

2017-10-30

Cosmological observations indicate that dark matter makes up 85% of all matter in the universe yet its microscopic composition remains a mystery. Dark matter could arise from ultralight quantum fields that form macroscopic objects. Here we use the global positioning system as a ~ 50,000 km aperture dark matter detector to search for such objects in the form of domain walls. Global positioning system navigation relies on precision timing signals furnished by atomic clocks. As the Earth moves through the galactic dark matter halo, interactions with domain walls could cause a sequence of atomic clock perturbations that propagate through the satellite constellation at galactic velocities ~ 300 km s -1 . Mining 16 years of archival data, we find no evidence for domain walls at our current sensitivity level. This improves the limits on certain quadratic scalar couplings of domain wall dark matter to standard model particles by several orders of magnitude.

Regulatory control of the use of contractors by operating organizations. Peer discussions on regulatory practices

International Nuclear Information System (INIS)

2000-09-01

This report arises from the eighth series of peer discussions on regulatory practices entitled 'Regulatory control of the use of contractors by operating organizations'. Senior regulators from 19 Member States participated in two peer group discussions in March 2000 and May 2000. This report gives an account of the outcomes of these meetings and of practical suggestions put forward by senior regulators. These suggestions do not necessarily reflect the views of the governments of the nominating Member States, the organizations they belong to, or the International Atomic Energy Agency. The objective of this document is to share experience between regulatory bodies and provide practical suggestions for controlling the use of contractors and subcontractors by the operating organizations during all stages, especially operation, of a nuclear power plant, so as to ensure that the quality of work and services delivered is commensurate with the safety importance of the activities and that these are carried out in a manner that will not adversely affect the safe or reliable operation of the facility. These documented practical suggestions and experiences are the result of a series of peer discussions at the IAEA in 2000. It is considered that the manner in which control is exercised, and the various challenges connected to this control, are highly dependent upon the legislative framework, maturity of the nuclear programme, the size of the national nuclear industry and the culture in each country. The report is structured so that it covers the subject matter under the following main headings: Legal Provisions, Regulatory Strategy and Requirements; Regulatory Approaches for Controlling the Use of Contractors; Types of Contracts; Practical Suggestions

Primordial black hole and wormhole formation by domain walls

Energy Technology Data Exchange (ETDEWEB)

Deng, Heling; Garriga, Jaume; Vilenkin, Alexander, E-mail: heling.deng@tufts.edu, E-mail: garriga@cosmos.phy.tufts.edu, E-mail: vilenkin@cosmos.phy.tufts.edu [Institute of Cosmology, Tufts University, 574 Boston Ave, Medford, MA, 02155 (United States)

2017-04-01

In theories with a broken discrete symmetry, Hubble sized spherical domain walls may spontaneously nucleate during inflation. These objects are subsequently stretched by the inflationary expansion, resulting in a broad distribution of sizes. The fate of the walls after inflation depends on their radius. Walls smaller than a critical radius fall within the cosmological horizon early on and collapse due to their own tension, forming ordinary black holes. But if a wall is large enough, its repulsive gravitational field becomes dominant much before the wall can fall within the cosmological horizon. In this ''supercritical'' case, a wormhole throat develops, connecting the ambient exterior FRW universe with an interior baby universe, where the exponential growth of the wall radius takes place. The wormhole pinches off in a time-scale comparable to its light-crossing time, and black holes are formed at its two mouths. As discussed in previous work, the resulting black hole population has a wide distribution of masses and can have significant astrophysical effects. The mechanism of black hole formation has been previously studied for a dust-dominated universe. Here we investigate the case of a radiation-dominated universe, which is more relevant cosmologically, by using numerical simulations in order to find the initial mass of a black hole as a function of the wall size at the end of inflation. For large supercritical domain walls, this mass nearly saturates the upper bound according to which the black hole cannot be larger than the cosmological horizon. We also find that the subsequent accretion of radiation satisfies a scaling relation, resulting in a mass increase by about a factor of 2.

High-R Walls for Remodeling: Wall Cavity Moisture Monitoring

Energy Technology Data Exchange (ETDEWEB)

Wiehagen, J.; Kochkin, V.

2012-12-01

The focus of the study is on the performance of wall systems, and in particular, the moisture characteristics inside the wall cavity and in the wood sheathing. Furthermore, while this research will initially address new home construction, the goal is to address potential moisture issues in wall cavities of existing homes when insulation and air sealing improvements are made.

High-R Walls for Remodeling. Wall Cavity Moisture Monitoring

Energy Technology Data Exchange (ETDEWEB)

Wiehagen, J. [NAHB Research Center Industry Partnership, Upper Marlboro, MD (United States); Kochkin, V. [NAHB Research Center Industry Partnership, Upper Marlboro, MD (United States)

2012-12-01

The focus of the study is on the performance of wall systems, and in particular, the moisture characteristics inside the wall cavity and in the wood sheathing. Furthermore, while this research will initially address new home construction, the goal is to address potential moisture issues in wall cavities of existing homes when insulation and air sealing improvements are made.

Regulatory philosophy and requirements for radiation control in Canadian uranium mine-mill facilities

International Nuclear Information System (INIS)

Dory, A.B.

1981-10-01

With the point made that radiation exposure is one of the health hazards of uranium mining and accordingly has to be controlled, the Canadian regulatory philosophy is outlined as it pertains to the uranium mining industry. Two extremes in regulatory approach are examined, and the joint regulatory process is explained. Two examples of poor management performance are given, and the role of mine unions in the regulatory process is touched upon. The development of new regulations to cover ventilation and employee training is sketched briefly. The author concludes with a general expression of objectives for the eighties which include improved personal dosimetry

Near Wall measurement in Turbulent Flow over Rough Wall using microscopic HPIV

Science.gov (United States)

Talapatra, Siddharth; Hong, Jiarong; Katz, Joseph

2009-11-01

Using holographic PIV, 3D velocity measurements are being performed in a turbulent rough wall channel flow. Our objective is to examine the contribution of coherent structures to the flow dynamics, momentum and energy fluxes in the roughness sublayer. The 0.45mm high, pyramid-shaped roughness is uniformly distributed on the top and bottom surfaces of a 5X20cm rectangular channel flow, where the Reτ is 3400. To facilitate recording of holograms through a rough plate, the working fluid is a concentrated solution of NaI in water, whose optical refractive index is matched with that of the acrylic rough plates. The test section is illuminated by a collimated laser beam from the top, and the sample volume extends from the bottom wall up to 7 roughness heights. After passing through the sample volume, the in-line hologram is magnified and recorded on a 4864X3248 pixels camera at a resolution of 0.74μm/pixel. The flow is locally seeded with 2μm particles. Reconstruction, spatial filtering and particle tracking provide the 3D velocity field. This approach has been successfully implemented recently, as preliminary data demonstrate.

Investigation of the functional role of CSLD proteins in plant cell wall deposition

Energy Technology Data Exchange (ETDEWEB)

Nielsen, Erik Etlar [Univ. of Michigan, Ann Arbor, MI (United States)

2017-11-21

The overall goal of this research proposal was to characterize the molecular machinery responsible for polarized secretion of cell wall components in Arabidopsis thaliana. We have used the polarized expansion that occurs during root hair cell growth to identify membrane trafficking pathways involved in polarized secretion of cell wall components to the expanding tips of these cells, and we have recently shown that CSLD3 is preferentially targeted to the apical plasma membranes in root hair cells, where it plays essential roles during cell wall deposition in these cells. The specific aims of the project are designed to answer the following objective: Identification of the cell wall polysaccharide class that CSLD proteins synthesize.

78 FR 1562 - Improving Government Regulations; Unified Agenda of Federal Regulatory and Deregulatory Actions

Science.gov (United States)

2013-01-08

... agenda incorporates the objective and criteria, when applicable, of the regulatory reform program under the Executive Order and other regulatory guidance. It contains DoD issuances initiated by DoD... statutory administration requirements as required. Starting with the fall 2007 edition, the Internet became...

Liquid Wall Chambers

Energy Technology Data Exchange (ETDEWEB)

Meier, W R

2011-02-24

The key feature of liquid wall chambers is the use of a renewable liquid layer to protect chamber structures from target emissions. Two primary options have been proposed and studied: wetted wall chambers and thick liquid wall (TLW) chambers. With wetted wall designs, a thin layer of liquid shields the structural first wall from short ranged target emissions (x-rays, ions and debris) but not neutrons. Various schemes have been proposed to establish and renew the liquid layer between shots including flow-guiding porous fabrics (e.g., Osiris, HIBALL), porous rigid structures (Prometheus) and thin film flows (KOYO). The thin liquid layer can be the tritium breeding material (e.g., flibe, PbLi, or Li) or another liquid metal such as Pb. TLWs use liquid jets injected by stationary or oscillating nozzles to form a neutronically thick layer (typically with an effective thickness of {approx}50 cm) of liquid between the target and first structural wall. In addition to absorbing short ranged emissions, the thick liquid layer degrades the neutron flux and energy reaching the first wall, typically by {approx}10 x x, so that steel walls can survive for the life of the plant ({approx}30-60 yrs). The thick liquid serves as the primary coolant and tritium breeding material (most recent designs use flibe, but the earliest concepts used Li). In essence, the TLW places the fusion blanket inside the first wall instead of behind the first wall.

Regulatory research program for 1987/88

International Nuclear Information System (INIS)

1987-01-01

The regulatory research program of Canada's Atomic Energy Control Board (AECB) is intended to augment the AECB's research program beyond the capability of in-house resources. The overall objective of the research program is to produce pertinent and independent information that will assist the Board and its staff in making correct, timely and credible decisions on regulating nuclear energy. The program covers the following areas: the safety of nuclear facilities, radioactive waste management, health physics, physical security, and the development of regulatory processes. Sixty-seven projects are planned for 1987/88; as well, there are some projects held in reserve in case funding becomes available. This information bulletin contains a list of the projects with a brief description of each

Desalination of Walls and Façades

Science.gov (United States)

Wedekind, W.; Jáuregui Arreola, K.; Siegesmund, S.

2012-04-01

For large monumental objects like walls and façades, the common technique of applying poultices for desalination often are not effective. This practice is neither cost effective nor does it lead to the desired result of desalination. To manage the conservation and desalination of these kinds of objects, several sprinkling techniques are known and have been applied on historical objects. For example, in the wooden warship Vasa, which was excavated from the sea bottom in Stockholm/Sweden, a sprinkling method was applied in 1961 for conservation and desalination. A sprinkling method to desalinate porous mineral materials will be presented using three different case studies: the rock cut monument no. 825 in Petra/Jordan, the medieval monastary church of the former Franziscan convent in Zeitz/Germany and the baroque monastary church Santa Monica in Guadalajara/Mexico. Before to start with practical conservation, the material- and petropysical properties, focoussed on water transport properties, like porosity, pore size distribution, water uptake and drying rate were investigadet. Diagnostic investigations on the objects included the mapping of deterioration, moister content measurements and salt accumulation determined by borehole cuts samples at depth. In the sprinkling method water is sprayed onto the wall surface through nozzels arranged in a modular grid. Depending on the sprinkling duration, a small or a large amount of water seeps into the porous materials, whereby the depth penetration can be adjusted accordingly. The water not absorbed by the stone runs off the facade and can be collected in liter amounts and tested by electrical conductivity with respect to the dissolved substances. After the drying of the wall's surface and the accumulation of salt at the material's surface, the procedure is repeated. For each subsequent washing a lower content of salt should be brought to the surface. Step by step the salt concentration will eventually decrease to almost

Rising damp in building walls: the wall base ventilation system

Energy Technology Data Exchange (ETDEWEB)

Guimaraes, A.S.; Delgado, J.M.P.Q.; Freitas, V.P. de [Faculdade de Engenharia da Universidade do Porto, Laboratorio de Fisica das Construcoes (LFC), Departamento de Engenharia Civil, Porto (Portugal)

2012-12-15

This work intends to validate a new system for treating rising damp in historic buildings walls. The results of laboratory experiments show that an efficient way of treating rising damp is by ventilating the wall base, using the HUMIVENT technique. The analytical model presented describes very well the observed features of rising damp in walls, verified by laboratory tests, who contributed for a simple sizing of the wall base ventilation system that will be implemented in historic buildings. (orig.)

Governmental, Legal and Regulatory Framework for Safety. General Safety Requirements. Part 1

Energy Technology Data Exchange (ETDEWEB)

NONE

2010-09-15

The objective of this publication is to establish requirements in respect of the governmental, legal and regulatory framework for safety. It covers the essential aspects of the framework for establishing a regulatory body and taking other actions necessary to ensure the effective regulatory control of facilities and activities utilized for peaceful purposes. Other responsibilities and functions, such as liaison within the global safety regime and on support services for safety (including radiation protection), emergency preparedness and response, nuclear security, and the State system of accounting for and control of nuclear material, are also covered.

CD4-regulatory cells in COPD patients

DEFF Research Database (Denmark)

Smyth, Lucy J C; Starkey, Cerys; Vestbo, Jørgen

2007-01-01

BACKGROUND: The numbers of airway CD8 and B lymphocytes are increased in COPD patients, suggesting an autoimmune process. CD4-regulatory T cells control autoimmunity but have not been studied in patients with COPD. OBJECTIVE: To compare T-regulatory cell numbers in the BAL from COPD patients......, smokers with normal lung function, and healthy nonsmokers (HNS). METHODS: BAL and peripheral blood mononuclear cell (PBMC) samples were obtained from 26 COPD patients, 19 smokers, and 8 HNS. Flow cytometry was performed for regulatory phenotypic markers. RESULTS: COPD patients had increased BAL CD8...... numbers compared to smokers and HNS. CD4 numbers were similar between groups. There was increased BAL CD4CD25(bright) expression in smokers (median 28.8%) and COPD patients (median 23.1%) compared to HNS (median 0%). Increased FoxP3 expression was confirmed in BAL CD4CD25(bright) cells. BAL CD4CD25 cells...

Abdominal wall reconstruction for incisional hernia optimizes truncal function and quality of life

DEFF Research Database (Denmark)

Jensen, Kristian K.; Munim, Kanzah; Kjaer, Michael

2017-01-01

Objective: The aim of the study was to examine abdominal wall function in patients undergoing abdominal wall reconstruction (AWR) for incisional hernia. Background: The literature on abdominal wall function in patients with incisional hernia is sparse. It has been suggested that AWR leads...... to improvement in function, but it is unknown whether this is specific to the abdominal wall or due to an improvement in overall physical fitness. Methods: We performed a prospective case-control study of 18 consecutive patients with large incisional hernia undergoing AWR with linea alba restoration. Truncal...... flexion and extension strength, hand grip strength, leg extension power, and quality of life (SF-36 and Carolinas Comfort Scale) were assessed preoperatively and 1 year postoperatively. Patients were compared with a control group of patients with an intact abdominal wall undergoing colorectal resection (n...

Handbook for value-impact assessments of NRC regulatory actions

International Nuclear Information System (INIS)

Mullen, M.F.; DiPalo, A.J.

1985-01-01

According to current Nuclear Regulatory Commission (NRC) procedures, value-impact (cost-benefit) assessments must be prepared for all rulemaking actions and for a broad range of other regulatory requirements and guidance. Probabilistic risk assessment (PRA) methods furnish an important part of the information base for these assessments. PRA methods are frequently the principal quantitative tool for estimating the benefits (e.g., public risk reduction) of proposed regulatory actions. In December 1983, the NRC published A Handbook for Value-Impact Assessment, NUREG/CR-3568, which provides a set of systematic procedures for performing value-impact assessments. The Handbook contains methods, data, and sources of information that can assist the regulatory analyst in conducting such assessments. The use of probabilistic risk analysis to estimate the benefits of proposed regulatory actions is described. Procedures and methods are also given for evaluating the costs and other consequences associated with regulatory actions. The Handbook has been adopted by the NRC as the recommended guideline for value impact assessments. This paper presents the background, objectives, and scope of the Handbook, describes the value-impact assessment methods (including the use of probabilistic risk assessment to estimate benefits), and discusses a selection of current and planned applications, with examples to illustrate how the methods are used

Clinical impact of ' in-treatment' wall motion abnormalities in hypertensive patients with left ventricular hypertrophy: the LIFE study

DEFF Research Database (Denmark)

Cicala, S.; Simone, G. de; Wachtell, K.

2008-01-01

Objectives Left ventricular systolic wall motion abnormalities have prognostic value. Whether wall motion detected by serial echocardiographic examinations predicts prognosis in hypertensive patients with left ventricular hypertrophy ( LVH) without clinically recognized atherosclerotic disease ha...

Supertube domain walls and elimination of closed timelike curves in string theory

International Nuclear Information System (INIS)

Drukker, Nadav

2004-01-01

We show that some novel physics of supertubes removes closed timelike curves from many supersymmetric spaces which naively suffer from this problem. The main claim is that supertubes naturally form domain walls, so while analytical continuation of the metric would lead to closed timelike curves, across the domain wall the metric is nondifferentiable, and the closed timelike curves are eliminated. In the examples we study, the metric inside the domain wall is always of the Goedel type, while outside the shell it looks like a localized rotating object, often a rotating black hole. Thus this mechanism prevents the appearance of closed timelike curves behind the horizons of certain rotating black holes

Roughness Effects on Organized Motions in a Wall Shear Layer Flow

Science.gov (United States)

Haigermoser, Christian; Vesely, Lukas; Lapolla, Massimillano; Onorato, Michele

2006-11-01

Turbulent boundary layer measurements on a zero-pressure gradient flat plate with two different roughness, a 2D and a 3D roughness, were carried out. The main object of the study was to investigate the impact of the wall roughness on the turbulent flow structures. The momentum thickness Reynolds number for the smooth wall was Reθ˜ 1900. PIV measurements were taken in the streamwise wall-normal plane. The PIV images covered the whole logarithmic region and the major part of the outer layer. The instant flow images for the two roughness show features similar to the one expected in a smooth wall turbulent boundary layer, as described by Adrian et al. (JFM 2000). Statistical analysis was performed to enlighten quantitative differences between the different flow fields. For instance, two point streamwise velocity correlations show that the major effect of the roughness is to tilt the inclination of the hairpin vortex packets towards the wall normal direction; being the 3D roughness more effective in producing this displacement. Full results will be shown and discussed during the presentation.

Interaction analysis of back-to-back mechanically stabilized earth walls

Directory of Open Access Journals (Sweden)

Sadok Benmebarek

2016-10-01

Full Text Available Back-to-back mechanically stabilized earth walls (BBMSEWs are encountered in bridge approaches, ramp ways, rockfall protection systems, earth dams, levees and noise barriers. However, available design guidelines for BBMSEWs are limited and not applicable to numerical modeling when back-to-back walls interact with each other. The objective of this paper is to investigate, using PLAXIS code, the effects of the reduction in the distance between BBMSEW, the reinforcement length, the quality of backfill material and the connection of reinforcements in the middle, when the back-to-back walls are close. The results indicate that each of the BBMSEWs behaves independently if the width of the embankment between mechanically stabilized earth walls is greater than that of the active zone. This is in good agreement with the result of FHWA design guideline. However, the results show that the FHWA design guideline underestimates the lateral earth pressure when back-to-back walls interact with each other. Moreover, for closer BBMSEWs, FHWA design guideline strongly overestimates the maximum tensile force in the reinforcement. The investigation of the quality of backfill material shows that the minor increase in embankment cohesion can lead to significant reductions in both the lateral earth pressure and the maximum tensile force in geosynthetic. When the distance between the two earth walls is close to zero, the connection of reinforcement between back-to-back walls significantly improves the factor of safety.

Performance-based quality assurance: the regulatory viewpoint

International Nuclear Information System (INIS)

Sajaroff, Pedro M.

2000-01-01

This paper complements and upgrades a previous one recently presented, the aim is a further contribution to a wide dissemination of this new methodology and way of thinking. Modern quality management techniques emphasizes errors prevention instead of finding and correcting them, in line with the new generation of ISO-9000 documents. Performance-based QA is coherent with this 'right-first-time' attitude, resting on the managerial role (establishing and applying policies and instructions allowing to integrate quality objectives to everyday work) and on the responsibility of every single involved person (the attainment of such objectives). The contents of the final draft of the revised IAEA NUSS Code on QA -namely 'Quality Assurance for Safety in Nuclear Power Plants and other Nuclear Facilities', is based on that approach, so it is not perspective. The text only contains ten basic requirements, where the objective is improving nuclear safety through an improvement in the methods applied for attaining quality during design, construction, commissioning, operation and decommissioning of nuclear installations. These requirements are assigned to: 'Management' (QA programme; training and qualification; non-conformance control and corrective actions; document control and records); 'Performance' (work; design; procurement; inspection and testing for acceptance) and 'Assessment' (management self-assessment; independent assessment). The management is responsible for planning, organization, direction, control and support; the line groups are responsible for attaining quality; and the assessment group is responsible for analyzing the management's and the line groups' effectiveness. From the regulatory point of view in the performance context, operating organizations will have to demonstrate the effective fulfillment of QA requirements to the satisfaction of regulatory authorities. This is not a novel mechanism, it is usual within the regulatory performance approach. The Code is

Regulatory activities

International Nuclear Information System (INIS)

2001-01-01

This publication, compiled in 8 chapters, presents the regulatory system developed by the Nuclear Regulatory Authority (NRA) of the Argentine Republic. The following activities and developed topics in this document describe: the evolution of the nuclear regulatory activity in Argentina; the Argentine regulatory system; the nuclear regulatory laws and standards; the inspection and safeguards of nuclear facilities; the emergency systems; the environmental systems; the environmental monitoring; the analysis laboratories on physical and biological dosimetry, prenatal irradiation, internal irradiation, radiation measurements, detection techniques on nuclear testing, medical program on radiation protection; the institutional relations with national and international organization; the training courses and meeting; the technical information

Classifying patients' complaints for regulatory purposes : A Pilot Study

NARCIS (Netherlands)

Bouwman, R.J.R.; Bomhoff, Manja; Robben, Paul; Friele, R.D.

2018-01-01

Objectives: It is assumed that classifying and aggregated reporting of patients' complaints by regulators helps to identify problem areas, to respond better to patients and increase public accountability. This pilot study addresses what a classification of complaints in a regulatory setting

Tension tests of concrete containment wall elements

International Nuclear Information System (INIS)

Schultz, D.M.; Julien, J.T.; Russel, H.G.

1984-01-01

Tension tests of concrete containment wall elements were conducted as part of a three-phase research program sponsored by the Electric Power Research Institute (EPRI). The objective of the EPRI experimental/analytical program is twofold. The first objective is to provide the utility industry with a test-verified analytical method for making realistic estimates of actual capacities of reinforced and prestressed concrete containments under internal over-pressurization from postulated degraded core accidents. The second objective is to determine qualitative and quantitative leak rate characteristics of typical containment cross-sections with and without penetrations. This paper covers the experimental portion to the EPRI program. The testing program for Phase 1 included eight large-scale specimens representing elements from the wall of a containment. Each specimen was 60-in (1525-mm) square, 24-in (610-mm) thick, and had full-size reinforcing bars. Six specimens were representative of prototypical reinforced concrete containment designs. The remaining two specimens represented prototypical prestressed containment designs. Various reinforcement configurations and loading arrangements resulted in data that permit comparisons of the effects of controlled variables on cracking and subsequent concrete/reinforcement/liner interaction in containment elements. Subtle differences, due to variations in reinforcement patterns and load applications among the eight specimens, are being used to benchmark the codes being developed in the analytical portion of the EPRI program. Phases 2 and 3 of the test program will examine leak rate characteristics and failure mechanisms at penetrations and structural discontinuities. (orig.)

Regulatory research and support program for 1992/93 - project descriptions. Information bulletin

International Nuclear Information System (INIS)

1992-01-01

The Regulatory Research and Support Program (RSP) is intended to augment and extend the Atomic Energy Control Board's regulatory program beyond the capability of in-house resources. The overall objective of the research and support program is to produce pertinent and independent information that will assist the Board and its staff in making correct, timely and credible decisions on regulating nuclear facilities and materials

Regulatory research and support program for 1992/93 - project descriptions. Information bulletin

Energy Technology Data Exchange (ETDEWEB)

NONE

1992-03-02

The Regulatory Research and Support Program (RSP) is intended to augment and extend the Atomic Energy Control Board`s regulatory program beyond the capability of in-house resources. The overall objective of the research and support program is to produce pertinent and independent information that will assist the Board and its staff in making correct, timely and credible decisions on regulating nuclear facilities and materials.

Automation of fusion first wall design using artificial intelligence technique

International Nuclear Information System (INIS)

Yoshimura, Shinobu; Yagawa, Genki; Mochizuki, Yoshihiko

1990-01-01

This paper describes the application of artificial intelligence techniques to a design automation of the fusion first wall to be operated in the complex environment where huge electromagnetic and thermal loading as well as heavy neutron irradiation occur. As a basic strategy of designing structure shape considering many coupled phenomena, an ordinary design procedure based on the generate and test strategy is adopted because of its simplicity and broad applicability. To automate the design procedure with maintaining its flexibility, extensibility and efficiency, artificial intelligence techniques are utilized in the following. An object-oriented knowledge representation technique is adopted to store knowledge modules, that is, objects, related to the first wall design, while a data-flow processing technique is utilized as an inference mechanism among the knowledge modules. These techniques realize the flexibility and extensibility of the system. Moreover, as an efficient design modification mechanism, which is essential in a design process, an empirical approach based on experts' empirical knowledge and a mathematical approach based on a kind of numerical sensitivity analysis are introduced. The developed system is applied to a simple example of the design of a two-dimensional model of the first wall with a cooling channel, and its fundamental performance is clearly demonstrated. (author)

Remnant Cholesterol Elicits Arterial Wall Inflammation and a Multilevel Cellular Immune Response in Humans

DEFF Research Database (Denmark)

Bernelot Moens, Sophie J; Verweij, Simone L; Schnitzler, Johan G

2017-01-01

cholesterol accumulates in human hematopoietic stem and progenitor cells coinciding with myeloid skewing. CONCLUSIONS: Patients with FD have increased arterial wall and cellular inflammation. These findings imply an important inflammatory component to the atherogenicity of remnant cholesterol, contributing......OBJECTIVE: Mendelian randomization studies revealed a causal role for remnant cholesterol in cardiovascular disease. Remnant particles accumulate in the arterial wall, potentially propagating local and systemic inflammation. We evaluated the impact of remnant cholesterol on arterial wall...... inflammation, circulating monocytes, and bone marrow in patients with familial dysbetalipoproteinemia (FD). APPROACH AND RESULTS: Arterial wall inflammation and bone marrow activity were measured using 18F-FDG PET/CT. Monocyte phenotype was assessed with flow cytometry. The correlation between remnant levels...

Current Status of Regulatory Science Education in Faculties of Pharmaceutical Science in Japan.

Science.gov (United States)

Tohkin, Masahiro

2017-01-01

I introduce the current pharmaceutical education system in Japan, focusing on regulatory science. University schools or faculties of pharmaceutical science in Japan offer two courses: a six-year course for pharmacists and a four-year course for scientists and technicians. Students in the six-year pharmaceutical course receive training in hospitals and pharmacies during their fifth year, and those in the four-year life science course start research activities during their third year. The current model core curriculum for pharmaceutical education requires them to "explain the necessity and significance of regulatory science" as a specific behavior object. This means that pharmacists should understand the significance of "regulatory science", which will lead to the proper use of pharmaceuticals in clinical practice. Most regulatory science laboratories are in the university schools or faculties of pharmaceutical sciences; however, there are too few to conduct regulatory science education. There are many problems in regulatory science education, and I hope that those problems will be resolved not only by university-based regulatory science researchers but also by those from the pharmaceutical industry and regulatory authorities.

Experimental assessment of dry stone retaining wall stability on a rigid foundation

OpenAIRE

Villemus , B.; Morel , J.C.; Boutin , C.

2007-01-01

International audience; Dry stone masonry retaining walls are present in the majority of mountainous areas all around the world, but the technique is marginal today in developed countries. The emergence of the concept of sustainable development calls for renewed use of this technique, both for the repair of existing retaining walls and the building of new ones. The objective of this research was to seek the knowledge necessary to ensure the stability of these structures, using experimental in...

Selection of exterior wall using advantageousness comparison; Ulkoseinaen valinta elinkaariedullisuuden perusteella

Energy Technology Data Exchange (ETDEWEB)

Saari, A.; Vesa, M.

2001-07-01

The objective of the study was to clarify the advantageousness of six chosen exterior wall solutions and at the same time to produce the procedure the measurement of the advantageousness. The examined wall types were: (1) brick wall, (2) brick-wool-concrete wall, (2b) brick-wool-concrete wall (not plastered), (3) brick-wool-wood wall, (4) precast concrete wall, and (5) plaster-wool-concrete wall. The analysis was made to a residential construction project which is built in a frame municipality of the metropolitan area. Here the life cycle costs, environmental burdens, and other factors (the aesthetic character, image, a comfort and easy maintenance) have an affect to the advantageousness of exterior wall. The averages of appreciation of the seven members of the supervising body of this study were used as the weights of the aforementioned value factors in the comparison. The result of the analysis was that the unplastered brick-wool-concrete wall had the equal life cycle costs as the precast concrete wall (an annual cost FIM 70 per apartment floor area). They were superior in relation to other examined wall types. In turn the brick wall had the highest life cycle costs (an annual cost nearly FIM 200 per apartment floor area) from the examined wall solutions on the advantageousness measuring straightforwardly likewise. It was chosen for an examination time period for 50 years. Likewise the brick wall was the distinctly weakest solution eco-economically, irrespective of, how costs and environmental factors are weighted. The brick wall was both the most expensive and unecological from the examined exterior wall types. It had a weak ecological qualities because considerably more building material than to other examined wall types. Also it's thermal insulation capacity was the weakest. But if in the decision-making also the aesthetic character, image, the effect on the comfort, and easy maintenance of the exterior wall indeed are included in addition to the eco

Automatic Adviser on Mobile Objects Status Identification and Classification

Science.gov (United States)

Shabelnikov, A. N.; Liabakh, N. N.; Gibner, Ya M.; Saryan, A. S.

2018-05-01

A mobile object status identification task is defined within the image discrimination theory. It is proposed to classify objects into three classes: object operation status; its maintenance is required and object should be removed from the production process. Two methods were developed to construct the separating boundaries between the designated classes: a) using statistical information on the research objects executed movement, b) basing on regulatory documents and expert commentary. Automatic Adviser operation simulation and the operation results analysis complex were synthesized. Research results are commented using a specific example of cuts rolling from the hump yard. The work was supported by Russian Fundamental Research Fund, project No. 17-20-01040.

Fabrication of a first wall panel by diffusion bonding

International Nuclear Information System (INIS)

Moreschi, L.F.; Pizzuto, A.; Alessandrini, I.

2002-01-01

Separated First Wall Panels mechanically attached to a shield block is now the reference concept for the Primary Wall Modules of RTO/RC ITER. The objective of the present work is to demonstrate the practical feasibility of a First Wall Panel utilizing a duplex round (steel) in square (copper) heat sink wound around a steel core and covered by Beryllium armour tiles. These three different materials (Be, Cu, steel) are joined together by diffusion bonding. The Copper alloy/stainless steel and Copper alloy/Beryllium joints were studied and developed selecting the optimal parameters for the related diffusion process. Several specimens were manufactured to be mechanically and thermally tested. The joints were mechanically tested using dedicated press equipment and investigated by micro-structural analysis with optical and SEM microscopy. Some thermal tests were finally carried out using an Electron Beam Facility. A dedicated R and D programme has led to the development of a co-drawing process, suitable for manufacturing the duplex Copper alloy-stainless steel heat sink. Two mock-ups were manufactured, the first in reduced-scale to test the thermal performance of the system, the second of larger scale and geometry better to represent the First Wall Panel

Evaluation of Coating Removal and Aggressive Surface Removal Surface Technologies Applied to Concrete Walls, Brick Walls, and Concrete Ceilings

International Nuclear Information System (INIS)

Ebadian, M.A.; Lagos, L.E.

1997-01-01

The purpose of this investigation was to test and evaluate innovative and commercially available technologies for the surface decontamination of walls and ceilings. This investigation supports the DOE's objectives of reducing risks to human health and the environment through its restoration projects at FEMP and MEMP. This project was performed at the Hemispheric Center for Environmental Technology (HCET) at Florida International University (FIU), where one innovative and four commercially available decontamination technologies were evaluated under standard, non-nuclear testing conditions. The performance data generated by this project will assist DOE site managers in the selection of the safest, most efficient, and most cost-effective decontamination technologies to accomplish their remediation objectives

Cell Wall Remodeling Enzymes Modulate Fungal Cell Wall Elasticity and Osmotic Stress Resistance.

Science.gov (United States)

Ene, Iuliana V; Walker, Louise A; Schiavone, Marion; Lee, Keunsook K; Martin-Yken, Hélène; Dague, Etienne; Gow, Neil A R; Munro, Carol A; Brown, Alistair J P

2015-07-28

The fungal cell wall confers cell morphology and protection against environmental insults. For fungal pathogens, the cell wall is a key immunological modulator and an ideal therapeutic target. Yeast cell walls possess an inner matrix of interlinked β-glucan and chitin that is thought to provide tensile strength and rigidity. Yeast cells remodel their walls over time in response to environmental change, a process controlled by evolutionarily conserved stress (Hog1) and cell integrity (Mkc1, Cek1) signaling pathways. These mitogen-activated protein kinase (MAPK) pathways modulate cell wall gene expression, leading to the construction of a new, modified cell wall. We show that the cell wall is not rigid but elastic, displaying rapid structural realignments that impact survival following osmotic shock. Lactate-grown Candida albicans cells are more resistant to hyperosmotic shock than glucose-grown cells. We show that this elevated resistance is not dependent on Hog1 or Mkc1 signaling and that most cell death occurs within 10 min of osmotic shock. Sudden decreases in cell volume drive rapid increases in cell wall thickness. The elevated stress resistance of lactate-grown cells correlates with reduced cell wall elasticity, reflected in slower changes in cell volume following hyperosmotic shock. The cell wall elasticity of lactate-grown cells is increased by a triple mutation that inactivates the Crh family of cell wall cross-linking enzymes, leading to increased sensitivity to hyperosmotic shock. Overexpressing Crh family members in glucose-grown cells reduces cell wall elasticity, providing partial protection against hyperosmotic shock. These changes correlate with structural realignment of the cell wall and with the ability of cells to withstand osmotic shock. The C. albicans cell wall is the first line of defense against external insults, the site of immune recognition by the host, and an attractive target for antifungal therapy. Its tensile strength is conferred by

Solar Walls in tsbi3

DEFF Research Database (Denmark)

Wittchen, Kim Bjarne

tsbi3 is a user-friendly and flexible computer program, which provides support to the design team in the analysis of the indoor climate and the energy performance of buildings. The solar wall module gives tsbi3 the capability of simulating solar walls and their interaction with the building....... This version, C, of tsbi3 is capable of simulating five types of solar walls say: mass-walls, Trombe-walls, double Trombe-walls, internally ventilated walls and solar walls for preheating ventilation air. The user's guide gives a description of the capabilities and how to simulate solar walls in tsbi3....

Innovations in rocking wall-frame systems-theory and development

Science.gov (United States)

Grigorian, Mark; Tavousi, Shayan

2017-09-01

The need to improve the seismic performance of buildings has brought about innovative systems such as rocking wall-moment frame (RWMF) combinations. The behavior of RWMFs can best be visualized by the moment-frame (MF) restraining the wall in place, and the rigid rocking wall (RRW) providing additional damping and imposing uniform drift along the height of the frame. A novel method of analysis followed by the development of a new lateral resisting system is introduced. The proposed concepts lead to an efficient structural configuration with provisions for self-centering, reparability, performance control, damage tolerance and collapse prevention. Exact, unique, closed form formulae have been provided to assess the collapse prevention and self-centering capabilities of the system. The objective is to provide an informative account of RWMF behavior for preliminary design as well as educational purposes. All formulae have been verified by independent computer analysis. Parametric examples have been provided to verify the validity of the proposed solutions.

Nuclear regulatory organisations: Learning from stakeholders to enhance communication

International Nuclear Information System (INIS)

Lorin, Aurelie

2015-01-01

Since its creation 15 years ago, the NEA Committee on Nuclear Regulatory Activities (CNRA) Working Group on Public Communication of Nuclear Regulatory Organisations (WGPC) has been addressing a broad range of communication issues, with two reports recently issued on Nuclear Regulatory Organisations, the Internet and Social Media: The What, How and Why of Their Use as Communication Tools and on Nuclear Regulatory Organisations and Communication Strategies. After the Fukushima Daiichi nuclear power plant accident in 2011, nuclear regulatory organisations around the world reaffirmed the need to strengthen stakeholder outreach and communication, and to create more robust avenues for stakeholder involvement in regulatory matters. The WGPC proposed a means for stakeholders to play a more active role in the group by holding one-day workshops in conjunction with regular meetings. These workshops offer a platform for stakeholder exchange with communication experts from nuclear regulatory organisations (NROs). The objective is to stimulate co-operation and improve communication by better understanding stakeholder perceptions, needs and expectations, and by discussing how to use traditional and social media more effectively. While nuclear regulatory organisations may have a common willingness to improve their communication methods and to build constructive relationships with stakeholders, every country has its own practices and cultural background, and thus its own challenges. Following the first workshop in Paris, which brought together European stakeholders, and the second in North America, the NEA is now organising a third workshop in Asia (Japan) to be held in April 2016. This third workshop will enable the NEA to gather stakeholder views from a third continent. A report on the workshops' findings will be issued after the completion of this third workshop, thus giving a broader idea of how to improve the overall communication methods of nuclear regulatory

Development of Questionnaire for Self-Assessment of Regulatory Capture

Energy Technology Data Exchange (ETDEWEB)

Muhmood, Ul Hassan; Lee, Young Eal [Pakistan Nuclear Regulatory Authority, Islamabad (Pakistan); Choi, Kwang Sik [Korea Institute of Nuclear Safety, Daejeon (Korea, Republic of)

2014-10-15

Nuclear industry with its evolution in 60s came with a number of pros and cons. In order to avoid any accident or incident, highest safety standards and quality control mechanism were established. The relation of regulator with its licensee is critical in the sense of public safety and welfare. The situation when the regulator starts to work for the interests of the industry instead of the public interest and fails to cling with his mission is known as 'regulatory capture' which may cause a number of serious negative effects like radiological or radiation risk. According to George Stigler, as a rule regulation is acquired by the industry and is designed and operated primarily for its benefit. The phenomenon of regulatory capture may hamper the safety culture and can also be considered as regulatory failure. It is therefore necessary to clearly understand this type of government failure to avoid the happening of serious accidents like TMI and Fukushima in the future. This paper aims to explore whether the regulatory body works independently and effectively to achieve its assigned tasks and objectives. Hence we proposed a questionnaire for the self-assessment of regulatory capture within the regulatory body. It also includes the results of an experimental assessment which was carried out to check the relevance and reliability of the questions to this subject. This assessment survey was conducted with the officers and staff members of Pakistan Nuclear Regulatory Authority (PNRA). We checked the significance of the proposed questionnaire and found some of the questions like Q. 27, 30 and 33 (written in italic) are not directly related to the phenomenon of regulatory capture. However, the existence of the situation which has been asked in these questions may lead towards the hampering of regulatory culture.

Development of Questionnaire for Self-Assessment of Regulatory Capture

International Nuclear Information System (INIS)

Muhmood, Ul Hassan; Lee, Young Eal; Choi, Kwang Sik

2014-01-01

Nuclear industry with its evolution in 60s came with a number of pros and cons. In order to avoid any accident or incident, highest safety standards and quality control mechanism were established. The relation of regulator with its licensee is critical in the sense of public safety and welfare. The situation when the regulator starts to work for the interests of the industry instead of the public interest and fails to cling with his mission is known as 'regulatory capture' which may cause a number of serious negative effects like radiological or radiation risk. According to George Stigler, as a rule regulation is acquired by the industry and is designed and operated primarily for its benefit. The phenomenon of regulatory capture may hamper the safety culture and can also be considered as regulatory failure. It is therefore necessary to clearly understand this type of government failure to avoid the happening of serious accidents like TMI and Fukushima in the future. This paper aims to explore whether the regulatory body works independently and effectively to achieve its assigned tasks and objectives. Hence we proposed a questionnaire for the self-assessment of regulatory capture within the regulatory body. It also includes the results of an experimental assessment which was carried out to check the relevance and reliability of the questions to this subject. This assessment survey was conducted with the officers and staff members of Pakistan Nuclear Regulatory Authority (PNRA). We checked the significance of the proposed questionnaire and found some of the questions like Q. 27, 30 and 33 (written in italic) are not directly related to the phenomenon of regulatory capture. However, the existence of the situation which has been asked in these questions may lead towards the hampering of regulatory culture

Politically Induced Regulatory Risk and Independent Regulatory Agencies

OpenAIRE

Strausz, Roland

2015-01-01

Uncertainty in election outcomes generates politically induced regulatory risk. Political parties' risk attitudes towards such risk depend on a fluctuation effect that hurts both parties and an output--expansion effect that benefits at least one party. Notwithstanding the parties' risk attitudes, political parties have incentives to negotiate away all regulatory risk by pre-electoral bargaining. Efficient pre-electoral bargaining outcomes fully eliminate politically induced regulatory risk. P...

Prioritization of gene regulatory interactions from large-scale modules in yeast

Directory of Open Access Journals (Sweden)

Bringas Ricardo

2008-01-01

Full Text Available Abstract Background The identification of groups of co-regulated genes and their transcription factors, called transcriptional modules, has been a focus of many studies about biological systems. While methods have been developed to derive numerous modules from genome-wide data, individual links between regulatory proteins and target genes still need experimental verification. In this work, we aim to prioritize regulator-target links within transcriptional modules based on three types of large-scale data sources. Results Starting with putative transcriptional modules from ChIP-chip data, we first derive modules in which target genes show both expression and function coherence. The most reliable regulatory links between transcription factors and target genes are established by identifying intersection of target genes in coherent modules for each enriched functional category. Using a combination of genome-wide yeast data in normal growth conditions and two different reference datasets, we show that our method predicts regulatory interactions with significantly higher predictive power than ChIP-chip binding data alone. A comparison with results from other studies highlights that our approach provides a reliable and complementary set of regulatory interactions. Based on our results, we can also identify functionally interacting target genes, for instance, a group of co-regulated proteins related to cell wall synthesis. Furthermore, we report novel conserved binding sites of a glycoprotein-encoding gene, CIS3, regulated by Swi6-Swi4 and Ndd1-Fkh2-Mcm1 complexes. Conclusion We provide a simple method to prioritize individual TF-gene interactions from large-scale transcriptional modules. In comparison with other published works, we predict a complementary set of regulatory interactions which yields a similar or higher prediction accuracy at the expense of sensitivity. Therefore, our method can serve as an alternative approach to prioritization for

Nuclear facilities and environment - an overview of regulatory aspects

International Nuclear Information System (INIS)

Chande, S.K.

2007-01-01

The Department of Atomic Energy (DAE) operates the entire range of nuclear fuel cycle facilities in the country. The radioactive wastes generated in these facilities have to be disposed into the environment without any adverse effect. In doing so, utmost care is taken to ensure the highest level of safety to the environment, the general public and the occupational workers. Atomic Energy Regulatory Board (AERB) is entrusted with the responsibility of protecting workers, public and environment against undue hazards from ionising radiations. To achieve this objective, AERB exercises regulatory control on the disposal of radioactive wastes from nuclear facilities. The disposal of radioactive effluents into the environment is governed by the Atomic Energy (Safe Disposal of Radioactive Wastes) Rules, 1987. The regulatory aspects with respect to disposal of radioactive wastes are discussed in this paper. (author)

Innovations in the Delivery of Regulatory Services in Australia

International Nuclear Information System (INIS)

Dillich, J.

2016-01-01

The Australian Radiation Protection and Nuclear Safety Agency (ARPANSA) is the country’s primary authority on radiation protection and nuclear safety. ARPANSA aims to promote safety, security, and emergency preparedness through efficient and effective regulation of nuclear installations, controlled facilities, and radiation sources. Recent initiatives to improve regulation by ‘cutting red tape’ and reducing regulatory burden have been introduced. ARPANSA’s Regulatory Delivery Model emphasises the key elements to good regulation and describes initiatives such as baseline inspection schedule, Performance Objectives and Criteria, and performance deficiencies. These and other initiatives have streamlined inspection efforts, increased risk-based oversight and risk-informed decision making, leading to increased efficiencies for both regulator and licence holder. In addition, ARPANSA has introduced 12 key performance indicators in its self-assessment of regulatory performance against the Australian Government’s Regulator Performance Framework. (author)

Using Piezoelectric Devices to Transmit Power through Walls

Science.gov (United States)

Sherrit, Stewart; Bar-Cohen, Yoseph; Bao, Xiaoqi

2008-01-01

A method denoted wireless acoustic-electric feed-through (WAEF) has been conceived for transmitting power and/or data signals through walls or other solid objects made of a variety of elastic materials that could be electrically conductive or nonconductive. WAEF would make it unnecessary to use wires, optical fibers, tubes, or other discrete wall-penetrating signal-transmitting components, thereby eliminating the potential for structural weakening or leakage at such penetrations. Avoidance of such penetrations could be essential in some applications in which maintenance of pressure, vacuum, or chemical or biological isolation is required. In a basic WAEF setup, a transmitting piezoelectric transducer on one side of a wall would be driven at resonance to excite ultrasonic vibrations in the wall. A receiving piezoelectric transducer on the opposite side of the wall would convert the vibrations back to an ultrasonic AC electric signal, which would then be detected and otherwise processed in a manner that would depend on the modulation (if any) applied to the signal and whether the signal was used to transmit power, data, or both. An electromechanical-network model has been derived as a computationally efficient means of analyzing and designing a WAEF system. This model is a variant of a prior model, known in the piezoelectric-transducer art as Mason's equivalent-circuit model, in which the electrical and mechanical dynamics, including electromechanical couplings, are expressed as electrical circuit elements that can include inductors, capacitors, and lumped-parameter complex impedances. The real parts of the complex impedances are used to account for dielectric, mechanical, and coupling losses in all components (including all piezoelectric-transducer, wall, and intermediate material layers). In an application to a three-layer piezoelectric structure, this model was shown to yield the same results as do solutions of the wave equations of piezoelectricity and acoustic

Solar collector wall with active curtain system; Lasikatteinen massiivienen aurinkokeraeaejaeseinae

Energy Technology Data Exchange (ETDEWEB)

Ojanen, T.; Heimonen, I. [VTT Building Technology, Espoo (Finland). Building Physics, Building Services and Fire Technology

1998-12-01

Integration of solar collector into the building envelope structure brings many advantages. The disadvantage of a passive solar collector wall is that its thermal performance can not be controlled, which may cause temporary overheating and low thermal efficiency of the collector. The thermal performance of the collector wall can be improved by using controllable, active collector systems. In this paper a solar collector wall with a controllable curtain between the transparent and absorption layers is investigated. The curtain is made of several low-emissivity foil layers, which ensures low radiation heat transfer through the curtain. The curtain decreases the heat losses out from the collector wall and it improves the U-value of the wall. The curtain is used when the solar radiation intensity to the wall is not high enough or when the wall needs protection against overheating during warm weather conditions. The materials and building components used in the collector wall, except those of the curtain, are ordinary in buildings. The transparent layer can be made by using normal glazing technology and the thermal storage layer can be made out of brick or similar material. The solar energy gains through the glazing can be utilised better than in passive systems, because the curtain provides the wall with high thermal resistance outside the solar radiation periods. The thermal performance of the collector wall was studied experimentally using a Hot-Box apparatus equipped with a solar lamp. Numerical simulations were carried out to study the yearly performance of the collector wall under real climate conditions. The objectives were to determine the thermal performance of the collector wall and to study how to optimise the use of solar radiation in this system. When the curtain with high thermal resistance is used actively, the temperature level of the thermal storage layer in the wall is relatively high also during dark periods and the heat losses out from the storage

Finite element limit loads for non-idealized through-wall cracks in thick-walled pipe

International Nuclear Information System (INIS)

Shim, Do-Jun; Han, Tae-Song; Huh, Nam-Su

2013-01-01

Highlights: • The lower bound bulging factor of thin-walled pipe can be used for thick-walled pipe. • The limit loads are proposed for thick-walled, transition through-wall cracked pipe. • The correction factors are proposed for estimating limit loads of transition cracks. • The limit loads of short transition cracks are similar to those of idealized cracks. - Abstract: The present paper provides plastic limit loads for non-idealized through-wall cracks in thick-walled pipe. These solutions are based on detailed 3-dimensional finite element (FE) analyses which can be used for structural integrity assessment of nuclear piping. To cover a practical range of interest, the geometric variables and loading conditions affecting the plastic limit loads of thick-walled pipe with non-idealized through-wall cracks were systematically varied. In terms of crack orientation, both circumferential and axial through-wall cracks were considered. As for loading conditions, axial tension, global bending, and internal pressure were considered for circumferential cracks, whereas only internal pressure was considered for axial cracks. Furthermore, the values of geometric factor representing shape characteristics of non-idealized through-wall cracks were also systematically varied. In order to provide confidence in the present FE analyses results, plastic limit loads of un-cracked, thick-walled pipe resulting from the present FE analyses were compared with the theoretical solutions. Finally, correction factors to the idealized through-wall crack solutions were developed to determine the plastic limit loads of non-idealized through-wall cracks in thick-walled pipe

Regulatory research and support program for 1989/90

International Nuclear Information System (INIS)

1989-01-01

The Regulatory Research and Support Program is intended to augment and extend the Atomic Energy Control Board's regulatory program beyond the capability of in-house resources. The overall objective of the research and support program is to produce pertinent and independent information that will assist the Board and its staff in making correct, timely and credible decisions on regulating nuclear energy. The program is divided into eight main areas of research covering the safety of nuclear facilities, radioactive waste management, health physics, physical security and the development of regulatory processes. A total of 83 projects are planned for 1989/90, including a number which are ongoing from the previous fiscal year. Projects that are held in reserve in case funding becomes available are also listed. Most of the projects will be carried out under contracts issued through the Department of Supply and Services. This Information Bulletin contains a list of the projects with a brief description of each, and additional supporting information

The PREEV project of the Latin American Forum.Regulatory practices on aging and life extension

International Nuclear Information System (INIS)

Figueras, J. M.

2011-01-01

The American Forum Plenary approved in 2008 the PREEV project, Regulatory Practices in Aging and Life Extension, whose main objective is to improve the regulatory action with regard to the management programs of life and long-term operation of nuclear power plants in the countries of the region Latin American.

Ascending Aortic Wall Cohesion: Comparison of Bicuspid and Tricuspid Valves

Directory of Open Access Journals (Sweden)

Jaroslav Benedik

2012-01-01

Full Text Available Objectives. Bicuspid aortic valve (AV represents the most common form of congenital AV malformation, which is frequently associated with pathologies of the ascending aorta. We compared the mechanical properties of the aortic wall between patients with bicuspid and tricuspid AV using a new custom-made device mimicking transversal aortic wall shear stress. Methods. Between 03/2010 and 07/2011, 190 consecutive patients undergoing open aortic valve replacement at our institution were prospectively enrolled, presenting either with a bicuspid (group 1, n=44 or a tricuspid (group 2, n=146 AV. Aortic wall specimen were examined with the “dissectometer” resulting in nine specific aortic-wall parameters derived from tensile strength curves (TSC. Results. Patients with a bicuspid AV showed significantly more calcified valves (43.2% versus 15.8%, P<0.001, and a significantly thinner aortic wall (2.04±0.42 mm versus 2.24±0.41 mm, P=0.008. Transesophageal echocardiography diameters (annulus, aortic sinuses, and sinotubular junction were significantly larger in the bicuspid group (P=0.003, P=0.02, P=0.01. We found no difference in the aortic wall cohesion between both groups as revealed by shear stress testing (P=0.72, P=0.40, P=0.41. Conclusion. We observed no differences of TSC in patients presenting with tricuspid or bicuspid AVs. These results may allow us to assume that the morphology of the AV and the pathology of the ascending aorta are independent.

Regulatory requirements for groundwater monitoring networks at hazardous waste sites

International Nuclear Information System (INIS)

Keller, J.F.

1989-10-01

In the absence of an explicit national mandate to protect groundwater quality, operators of active and inactive hazardous waste sites must use a number of statutes and regulations as guidance for detecting, correcting, and preventing groundwater contamination. The objective of this paper is to provide a framework of the technical and regulatory considerations that are important to the development of groundwater monitoring programs at hazardous waste sites. The technical site-specific needs and regulatory considerations, including existing groundwater standards and classifications, will be presented. 14 refs., 2 tabs

Development of K and COD Solutions of Non-idealized Circumferential Through-wall Cracks for PARTRIDGE

International Nuclear Information System (INIS)

Park, Jeong Soon; Kim, Sun Hye; Kim, Jin Su and others

2013-01-01

PARTRIDGE (Probabilistic Analysis as a Regulatory Tool for Risk Informed Decision GuidancE) is an international research program, main purposes of which are to enhance PRO-LOCA (PRObabilistic-Loss Of Coolant Accident) code, a research piping probabilistic fracture mechanics code originally developed for USNRC, and to support the development of a new modular probabilistic fracture mechanics code, xLPR(Extremely Low Probability of Rupture). KINS, KHNP, and KEPCO E and C established a Korea Consortium to take part in the PARTRIDGE and have provided not only financial but also technical contribution to it. As part of the research in-kind contribution, Korea Consortium has developed new Mode I stress intensity factors (KI) and crack opening displacements (COD, δ) for non-idealized through-wall cracks along with EMC2 (Engineering Mechanics Corporation of Columbus). In this paper, the results of linear elastic fracture mechanics (LEFM) analysis for non-idealized circumferential through-wall cracks performed by Korea Consortium were provided. Korea Consortium, KINS, KHNP, and KEPCO E and C, performs LEFM analyses for non-idealized circumferential through-wall cracks as part of in-kind contribution to the international research program called PARTRIDGE

Organization of nuclear regulatory activities

International Nuclear Information System (INIS)

Blidaru, Valentin

2008-01-01

The paper presents the structure, missions and organizational aspects of the CNCAN, the National Commission for the control of nuclear activities in Romania. The paper addresses the following main issues: 1.General aspects; 2.Organizational structure of the NRA in Romania; 3.General description of the Division for Nuclear Safety Assessments; 4.Specific activities; 5.Regulatory approaches and practices. Under the title of 'General aspects' the following three basic statements are highlighted: 1.CNCAN is a governmental organization responsible for the development of the regulatory framework, the control of its implementation and the licensing of nuclear facilities; 2.CNCAN is the national authority competent in exercising the regulatory activity, authorization and control in the nuclear field provided by the law No. 111/ 1996 republished in 1998; 3.The Commission exercises its functions independently of the ministries and other authorities of the public control administration being subordinated to the Romanian Government. The organizational structure is as follows: - President, the Managerial Council and the Advisory Council coordinating the four General Divisions that are responsible for: - Nuclear Safety with Division of Nuclear Safety Assessment and Division of Nuclear Objectives Surveillance; - Radiological Safety with Division of Radiological Safety Assessment and Division of Operational Radiation Protection; - Surveillance of Environmental Radioactivity with Division of Assessment and Analysis and Division of National Network; - Development and Resource with the Division of Economy and Division of Human Resources. In addition under direct coordination of the President operate the Division of Radiation Protection, Transport and Radioactive Waste and the Division of International Cooperation and Communication. Specific activities are listed describing among others the issues of: - Safety of nuclear installation; - Evaluation relating to licensing of nuclear

Reflections on a flat wall

International Nuclear Information System (INIS)

Stevenson, G.R.; Huhtinen, M.

1995-01-01

This paper describes an investigation into whether estimates of attenuation in the flat sidewalls of the tunnel for the MC main ring can be based on a simple point-source/line-of-sight model. Having seen the limitations of such a model, an alternative is proposed where the main radiation source is not the initial object struck by the beam but the plane source provided by the first interactions of secondaries from the target in the shield-wall. This is shown to have a closer relation to reality than the point-source/line-of-sight model. (author)

Regulatory research program for 1986/87 project descriptions. Information bulletin 86-1

Energy Technology Data Exchange (ETDEWEB)

NONE

1986-07-08

The regulatory research program is intended to augment and extend the Atomic Energy Control Board`s regulatory program beyond the capability of in-house resources. The overall objective of the research program is to produce pertinent and independent information that will assist the Board and its staff in making correct, timely and credible decisions on regulating nuclear energy. The program is divided into ten main areas of research covering the safety of nuclear facilities, radioactive waste management, health physics, physical security and the development of regulatory processes. A total of 92 projects are planned for 1986/87, including a number which are ongoing from the previous fiscal year.

Regulatory research program for 1986/87 project descriptions. Information bulletin 86-1

International Nuclear Information System (INIS)

1986-01-01

The regulatory research program is intended to augment and extend the Atomic Energy Control Board's regulatory program beyond the capability of in-house resources. The overall objective of the research program is to produce pertinent and independent information that will assist the Board and its staff in making correct, timely and credible decisions on regulating nuclear energy. The program is divided into ten main areas of research covering the safety of nuclear facilities, radioactive waste management, health physics, physical security and the development of regulatory processes. A total of 92 projects are planned for 1986/87, including a number which are ongoing from the previous fiscal year

The use of joint reinforcement in qualifying masonry walls in nuclear power plants

International Nuclear Information System (INIS)

Harris, H.G.; Becica, I.J.; Chokshi, N.C.; Con, V.N.; Hamid, A.A.

1984-01-01

Wire joint reinforcement has been traditionally used in block masonry walls for crack control and to provide continuity for multiple wythe walls. In a number of nuclear power plants, vertically unreinforced masonry walls that failed to meet the code allowable stresses for unreinforced masonry were qualified using joint reinforcement as a structural steel to carry lateral loads in the horizontal direction. It is the objective of this paper to examine the adequacy of this approach for seismic load application. A state-of-the-art review of available test data and code design provisions will be presented. It is concluded that the use of joint reinforcement to resist tensile stresses due to seismic loading is questionable because of the lack of test data available and especially the characterization of the cyclic behavior of joint reinforced masonry walls. Further research in this area is recommended

Ambiguous walls

DEFF Research Database (Denmark)

Mody, Astrid

2012-01-01

The introduction of Light Emitting Diodes (LEDs) in the built environment has encouraged myriad applications, often embedded in surfaces as an integrated part of the architecture. Thus the wall as responsive luminous skin is becoming, if not common, at least familiar. Taking into account how wall...

Simulations and Experiments on Vibration Control of Aerospace Thin-Walled Parts via Preload

Directory of Open Access Journals (Sweden)

Qiong Wu

2017-01-01

Full Text Available Thin-walled parts primarily comprise the entire piece of rough machining, and the material removal rate can surpass 95%. Numerous components with thin-walled structures are preferred in the aerospace industry for their light weight, high strength, and other advantages. In aerospace thin-walled workpiece machining processes and practical applications, they are excited by the vibration. The preload changing the modal stiffness of the part is found and this change causes continuous changes in the natural frequency. Researching on the influence of pretightening force on dynamic characteristics of thin-walled components is highly significant for controlling vibration. In this study, the typical aviation thin-walled part is the research object. Finite element numerical simulation and experimental verification are employed to analyze the dynamic characteristics of 7075 aluminum alloy thin-walled plates under different preloads for exploring the relationship between natural frequency and preload. The relationship is validated by comparative results. Both the simulation and experimental results show that the natural frequencies of plates increase following the augmentation of the preload. Thus, this research introduces the method where vibration of aerospace thin-walled parts is reduced by preload. For practical engineering application, a program showing the relationship between natural frequency and preload is written using Visual Basic language.

Governmental, Legal and Regulatory Framework for Safety. General Safety Requirements. Part 1 (Spanish Edition)

International Nuclear Information System (INIS)

2010-01-01

The objective of this publication is to establish requirements in respect of the governmental, legal and regulatory framework for safety. It covers the essential aspects of the framework for establishing a regulatory body and taking other actions necessary to ensure the effective regulatory control of facilities and activities utilized for peaceful purposes. Other responsibilities and functions, such as liaison within the global safety regime and on support services for safety (including radiation protection), emergency preparedness and response, nuclear security, and the State system of accounting for and control of nuclear material, are also covered

Governmental, Legal and Regulatory Framework for Safety. General Safety Requirements. Part 1 (French Edition)

International Nuclear Information System (INIS)

2010-01-01

The objective of this publication is to establish requirements in respect of the governmental, legal and regulatory framework for safety. It covers the essential aspects of the framework for establishing a regulatory body and taking other actions necessary to ensure the effective regulatory control of facilities and activities utilized for peaceful purposes. Other responsibilities and functions, such as liaison within the global safety regime and on support services for safety (including radiation protection), emergency preparedness and response, nuclear security, and the State system of accounting for and control of nuclear material, are also covered

Governmental, Legal and Regulatory Framework for Safety. General Safety Requirements. Part 1 (Chinese Edition)

International Nuclear Information System (INIS)

2010-01-01

The objective of this publication is to establish requirements in respect of the governmental, legal and regulatory framework for safety. It covers the essential aspects of the framework for establishing a regulatory body and taking other actions necessary to ensure the effective regulatory control of facilities and activities utilized for peaceful purposes. Other responsibilities and functions, such as liaison within the global safety regime and on support services for safety (including radiation protection), emergency preparedness and response, nuclear security, and the State system of accounting for and control of nuclear material, are also covered

Governmental, Legal and Regulatory Framework for Safety. General Safety Requirements. Part 1 (Arabic Edition)

Energy Technology Data Exchange (ETDEWEB)

NONE

2010-09-15

The objective of this publication is to establish requirements in respect of the governmental, legal and regulatory framework for safety. It covers the essential aspects of the framework for establishing a regulatory body and taking other actions necessary to ensure the effective regulatory control of facilities and activities utilized for peaceful purposes. Other responsibilities and functions, such as liaison within the global safety regime and on support services for safety (including radiation protection), emergency preparedness and response, nuclear security, and the State system of accounting for and control of nuclear material, are also covered.

Evaluation of Coating Removal and Aggressive Surface Removal Surface Technologies Applied to Concrete Walls, Brick Walls, and Concrete Ceilings

Energy Technology Data Exchange (ETDEWEB)

Lagos, L.E.; Ebadian, M.A.

1997-11-01

The purpose of this investigation was to test and evaluate innovative and commercially available technologies for the surface decontamination of walls and ceilings. This investigation supports the DOE's objectives of reducing risks to human health and the environment through its restoration projects at FEMP and MEMP. This project was performed at the Hemispheric Center for Environmental Technology (HCET) at Florida International University (FIU), where one innovative and four commercially available decontamination technologies were evaluated under standard, non-nuclear testing conditions. The performance data generated by this project will assist DOE site managers in the selection of the safest, most efficient, and most cost-effective decontamination technologies to accomplish their remediation objectives.

Regulatory networks in pollen development under cold stress

Directory of Open Access Journals (Sweden)

Kamal Dev Sharma

2016-03-01

Full Text Available Cold stress modifies anthers’ metabolic pathways to induce pollen sterility. Cold-tolerant plants, unlike the susceptible ones, produce high proportion of viable pollen. Anthers in susceptible plants, when exposed to cold stress, increase abscisic acid (ABA metabolism and reduce ABA catabolism. Increased ABA negatively regulates expression of tapetum cell wall bound invertase and monosaccharide transport genes resulting in distorted carbohydrate pool in anther. Cold-stress also reduces endogenous levels of the bioactive gibberellins (GAs, GA4 and GA7, in susceptible anthers by repression of the GA biosynthesis genes. Here we discuss recent findings on mechanisms of cold susceptibility in anthers which determine pollen sterility. We also discuss differences in regulatory pathways between cold-stressed anthers of susceptible and tolerant plants that decide pollen sterility or viability.

Effects of wall roughness and entry length on void profile in vertical bubbly flow

International Nuclear Information System (INIS)

Takamasa, Tomoji

1988-01-01

An experimental study of upward air-water bubbly two-phase flow in an entry region was performed with various rough wall test tubes. The objective of the work is to clarify the effects of wall roughness and entry length on void profile. The fluid flows in the vertical circular test tube of 25 mm I.D. under nearly atmospheric pressure, at room temperature. The void profile changes from a pattern similar in appearance to the saddle shape which has local void peaks near the wall, into the power law shape whose curve is approximated by a power law formula, with increasing wall roughness and/or entry length. That is, wall roughness and entry length have a similar effect upon void profile. There are two patterns in the power law shape, a pattern with sharp center peak and a pattern with obtuse center peak. As wall roughness and/or entry length increase, the void profile changes from the former pattern to the latter pattern. At enough long entry length (L/D ≅ 150), every void profile has almost the same power law shape independent of wall roughness. Some void profiles are asymmetric to the axis. (author)

Operational Windows for Dry-Wall and Wetted-Wall IFE Chambers

International Nuclear Information System (INIS)

Najmabadi, F.; Raffray, A.R.; Bromberg, L.

2004-01-01

The ARIES-IFE study was an integrated study of inertial fusion energy (IFE) chambers and chamber interfaces with the driver and target systems. Detailed analysis of various subsystems was performed parametrically to uncover key physics/technology uncertainties and to identify constraints imposed by each subsystem. In this paper, these constraints (e.g., target injection and tracking, thermal response of the first wall, and driver propagation and focusing) were combined to understand the trade-offs, to develop operational windows for chamber concepts, and to identify high-leverage research and development directions for IFE research. Some conclusions drawn in this paper are (a) the detailed characterization of the target yield and spectrum has a major impact on the chamber; (b) it is prudent to use a thin armor instead of a monolithic first wall for dry-wall concepts; (c) for dry-wall concepts with direct-drive targets, the most stringent constraint is imposed by target survival during the injection process; (d) for relatively low yield targets (<250 MJ), an operational window with no buffer gas may exist; (e) for dry-wall concepts with indirect-drive targets, a high buffer gas pressure would be necessary that may preclude propagation of the laser driver and require assisted pinch transport for the heavy-ion driver; and (f) generation and transport of aerosols in the chamber is the key feasibility issue for wetted-wall concepts

Hard wall - soft wall - vorticity scattering in shear flow

NARCIS (Netherlands)

Rienstra, S.W.; Singh, D.K.

2014-01-01

An analytically exact solution, for the problem of lowMach number incident vorticity scattering at a hard-soft wall transition, is obtained in the form of Fourier integrals by using theWiener-Hopf method. Harmonic vortical perturbations of inviscid linear shear flow are scattered at the wall

Hard wall - soft wall - vorticity scattering in shear flow

NARCIS (Netherlands)

Rienstra, S.W.; Singh, D.K.

2014-01-01

An analytically exact solution, for the problem of low Mach number incident vorticity scattering at a hard-soft wall transition, is obtained in the form of Fourier integrals by using the Wiener-Hopf method. Harmonic vortical perturbations of inviscid linear shear flow are scattered at the wall

Safety culture competition - expectations of a regulatory authority

International Nuclear Information System (INIS)

Keil, D.; Gloeckle, W.

2000-01-01

The accident at the Chernobyl nuclear power station on April 26, 1986 influenced the development of reactor safety and promulgated two basic concepts especially in Germany. On the one hand, extensive measures of in-plant accident management have greatly reduced the so-called residual risk. On the other hand, a comprehensive safety approach has been initiated which comprises the nuclear power plant as a system together with people, technology, and organization and also includes safety culture. In a modern regulatory concept based on the dynamic development of safety, the authority's classical regulatory function of controlling is supplemented by the objective of promoting safety. While preserving the division of responsibilities between the regulatory authority and plant operators, the authority uses 'constructive critical dialog' as a tool to enhance safety. Besides the regulatory assessment of safety culture on the basis of indications or indicators, also the continuous promotion of safety culture in a dialog with plant operators is seen as one of the duties of a regulatory authority. Continued efforts are necessary to maintain the high level of safety culture in German nuclear power plants. Operators are expected to establish a safety management which assigns top priority to safety issues, and which pursues the goal of supervising and promoting safety culture. Developments on the deregulated electricity markets must not lead to safety aspects ranking second to economic aspects. Moreover, also under changed boundary conditions, only the safe operation of nuclear power plants ensures economic viability. (orig.) [de

Plant cell wall extensibility: connecting plant cell growth with cell wall structure, mechanics, and the action of wall-modifying enzymes

Energy Technology Data Exchange (ETDEWEB)

Cosgrove, Daniel J.

2015-11-25

The advent of user-friendly instruments for measuring force/deflection curves of plant surfaces at high spatial resolution has resulted in a recent outpouring of reports of the ‘Young's modulus’ of plant cell walls. The stimulus for these mechanical measurements comes from biomechanical models of morphogenesis of meristems and other tissues, as well as single cells, in which cell wall stress feeds back to regulate microtubule organization, auxin transport, cellulose deposition, and future growth directionality. In this article I review the differences between elastic modulus and wall extensibility in the context of cell growth. Some of the inherent complexities, assumptions, and potential pitfalls in the interpretation of indentation force/deflection curves are discussed. Reported values of elastic moduli from surface indentation measurements appear to be 10- to >1000-fold smaller than realistic tensile elastic moduli in the plane of plant cell walls. Potential reasons for this disparity are discussed, but further work is needed to make sense of the huge range in reported values. The significance of wall stress relaxation for growth is reviewed and connected to recent advances and remaining enigmas in our concepts of how cellulose, hemicellulose, and pectins are assembled to make an extensible cell wall. A comparison of the loosening action of α-expansin and Cel12A endoglucanase is used to illustrate two different ways in which cell walls may be made more extensible and the divergent effects on wall mechanics.

Strengthening Regulatory Competence in a Changing Nuclear Regulatory Environment

International Nuclear Information System (INIS)

Illizastigui, P.F.

2016-01-01

The paper addresses the approach followed by the Cuban National Center for Nuclear Safety for the management of current and new competences of its regulatory staff with the aim of allowing those staff to effectively fulfill their core regulatory functions. The approach is realized through an Integrated System for Competence Building, which is based on the IAEA recommendations, shown to be effective in ensuring the necessary competence in the relevant areas. In the author’s opinion, competence of the regulatory staff in the area of human and organizational factors is of paramount importance and needs to be further strengthened in order to be able to assess safety performance at the facilities and detect early signs of deteriorating safety performance. The former is defined by the author as the core regulatory function “Analysis” which covers the entire spectrum of assessment tasks carried out by the regulatory staff to: a) detect declining safety performance, b) diagnose latent weaknesses (root causes) and c) make effective safety culture interventions. The author suggests that competence associated with the fulfillment of the analysis function is distinctly identified and dealt with separately in the current system of managing regulatory competence. (author)

Regulatory approaches to hydrocarbon contamination from underground storage tanks

International Nuclear Information System (INIS)

Daugherty, S.J.

1991-01-01

Action or lack of action by the appropriate regulatory agency is often the most important factor in determining remedial action or closure requirements for hydrocarbon contaminated sites. This paper reports that the diversity of regulatory criteria is well known statewide and well documented nationally. In California, the diversity of approaches is due to: that very lack of a clear understanding of the true impact of hydrocarbon contamination: lack of state or federal standards for soil cleanup, and state water quality objectives that are not always achievable; vagueness in the underground storage tank law; and the number and diversity of agencies enforcing the underground storage tank regulations

Airway wall thickening and emphysema show independent familial aggregation in chronic obstructive pulmonary disease

DEFF Research Database (Denmark)

Patel, Bipen D; Coxson, Harvey O; Pillai, Sreekumar G

2008-01-01

RATIONALE: It is unclear whether airway wall thickening and emphysema make independent contributions to airflow limitation in chronic obstructive pulmonary disease (COPD) and whether these phenotypes cluster within families. OBJECTIVES: To determine whether airway wall thickening and emphysema (1...... to airflow obstruction in COPD. These phenotypes show independent aggregation within families of individuals with COPD, suggesting that different genetic factors influence these disease processes....... the severity of airway wall thickening and emphysema. MEASUREMENTS AND MAIN RESULTS: A total of 3,096 individuals were recruited to the study, of whom 1,159 (519 probands and 640 siblings) had technically adequate high-resolution computed tomography scans without significant non-COPD-related thoracic disease...

Improved cost-benefit techniques in the US Nuclear Regulatory Commission

Energy Technology Data Exchange (ETDEWEB)

Cronin, F.J.; Nesse, R.J.; Vaeth, M.; Wusterbarth, A.R.; Currie, J.W.

1983-06-01

The major objective of this report is to help the US Nuclear Regulatory Commission (NRC) in its regulatory mission, particularly with respect to improving the use of cost-benefit analysis and the economic evaluation of resources within the NRC. The objectives of this effort are: (1) to identify current and future NRC requirements (e.g., licensing) for valuing nonmarket goods; (2) to identify, highlight, and present the relevant efforts of selected federal agencies, some with over two decades of experience in valuing nonmarket goods, in this area; and (3) to review methods for valuing nonmarket impacts and to provide estimats of their magnitudes. Recently proposed legislation may result in a requirement for not only more sophisticated valuation analyses, but more extensive applications of these techniques to issues of concern to the NRC. This paper is intended to provide the NRC with information to more efficiently meet such requirements.

Improving clinical drug development regulatory procedures for anticonvulsants

Directory of Open Access Journals (Sweden)

Janković Slobodan

2015-01-01

Full Text Available Background: Clinical development of antiepileptic drugs is demanding due to complex character of the disorder and to diversity of its forms and etiologies. Objective: The aim of this review was to suggest improvements in regulatory procedures for clinical development of antiepileptic drugs. Methods: The following databases of scientific articles were searched: MEDLINE, SCOPUS and SCINDEKS. In total 558 publications were retrieved. The types of articles selected were reviews, reports on clinical trials and letters to the Editor. Results: There are several changes of regulatory documents necessary for improving process of clinical development of antiepileptic drugs: preference of parallel groups design for add-on trials should be explicit; the noninferiority design for monotherapy clinical trials should be acceptable; restrictive formulations when trials of antiepileptic drugs in children are in question should be avoided; requirements in regard to the efficacy measures should be harmonized among the regulatory bodies; proactive attitude towards discovery of adverse events; and precise requirements for clinical trials specifically designed to prove anti-epileptogenic effects should be made clear. Conclusion: Current regulatory documents are incomplete in many aspects; an international effort to improve and harmonize guidelines for clinical development of antiepileptic drugs is necessary for improvement of this process.

WASTE HANDLING BUILDING SHIELD WALL ANALYSIS

International Nuclear Information System (INIS)

Padula, D.

2000-01-01

The scope of this analysis is to estimate the shielding wall, ceiling or equivalent door thicknesses that will be required in the Waste Handling Building to maintain the radiation doses to personnel within acceptable limits. The shielding thickness calculated is the minimum required to meet administrative limits, and not necessarily what will be recommended for the final design. The preliminary evaluations will identify the areas which have the greatest impact on mechanical and facility design concepts. The objective is to provide the design teams with the necessary information to assure an efficient and effective design

Abdominal wall fat pad biopsy

Science.gov (United States)

Amyloidosis - abdominal wall fat pad biopsy; Abdominal wall biopsy; Biopsy - abdominal wall fat pad ... is the most common method of taking an abdominal wall fat pad biopsy . The health care provider cleans the ...

Spontaneous and controlled-diameter synthesis of single-walled and few-walled carbon nanotubes

Science.gov (United States)

Inoue, Shuhei; Lojindarat, Supanat; Kawamoto, Takahiro; Matsumura, Yukihiko; Charinpanitkul, Tawatchai

2018-05-01

In this study, we explored the spontaneous and controlled-diameter growth of carbon nanotubes. We evaluated the effects of catalyst density, reduction time, and a number of catalyst coating on the substrate (for multi-walled carbon nanotubes) on the diameter of single-walled carbon nanotubes and the number of layers in few-walled carbon nanotubes. Increasing the catalyst density and reduction time increased the diameters of the carbon nanotubes, with the average diameter increasing from 1.05 nm to 1.86 nm for single-walled carbon nanotubes. Finally, we succeeded in synthesizing a significant double-walled carbon nanotube population of 24%.

Regulation of Cell Wall Biogenesis in Saccharomyces cerevisiae: The Cell Wall Integrity Signaling Pathway

Science.gov (United States)

Levin, David E.

2011-01-01

The yeast cell wall is a strong, but elastic, structure that is essential not only for the maintenance of cell shape and integrity, but also for progression through the cell cycle. During growth and morphogenesis, and in response to environmental challenges, the cell wall is remodeled in a highly regulated and polarized manner, a process that is principally under the control of the cell wall integrity (CWI) signaling pathway. This pathway transmits wall stress signals from the cell surface to the Rho1 GTPase, which mobilizes a physiologic response through a variety of effectors. Activation of CWI signaling regulates the production of various carbohydrate polymers of the cell wall, as well as their polarized delivery to the site of cell wall remodeling. This review article centers on CWI signaling in Saccharomyces cerevisiae through the cell cycle and in response to cell wall stress. The interface of this signaling pathway with other pathways that contribute to the maintenance of cell wall integrity is also discussed. PMID:22174182

Regulatory Challenges for Cartilage Repair Technologies.

Science.gov (United States)

McGowan, Kevin B; Stiegman, Glenn

2013-01-01

In the United States, few Food and Drug Administration (FDA)-approved options exist for the treatment of focal cartilage and osteochondral lesions. Developers of products for cartilage repair face many challenges to obtain marketing approval from the FDA. The objective of this review is to discuss the necessary steps for FDA application and approval for a new cartilage repair product. FDA Guidance Documents, FDA Panel Meetings, scientific organization recommendations, and clinicaltrials.gov were reviewed to demonstrate the current thinking of FDA and the scientific community on the regulatory process for cartilage repair therapies. Cartilage repair therapies can receive market approval from FDA as medical devices, drugs, or biologics, and the specific classification of product can affect the nonclinical, clinical, and regulatory strategy to bring the product to market. Recent FDA guidance gives an outline of the required elements to bring a cartilage repair product to market, although these standards are often very general. As a result, companies have to carefully craft their study patient population, comparator group, and clinical endpoint to best showcase their product's attributes. In addition, regulatory strategy and manufacturing process validation need to be considered early in the clinical study process to allow for timely product approval following the completion of clinical study. Although the path to regulatory approval for a cartilage repair therapy is challenging and time-consuming, proper clinical trial planning and attention to the details can eventually save companies time and money by bringing a product to the market in the most expeditious process possible.

Orbital wall fractures

International Nuclear Information System (INIS)

Iinuma, Toshitaka; Ishio, Ken-ichirou; Yoshinami, Hiroyoshi; Kuriyama, Jun-ichi; Hirota, Yoshiharu.

1993-01-01

A total of 59 cases of mild facial fractures (simple orbital wall fractures, 34 cases, other facial fractures, 25 cases) with the clinical suspects of orbital wall fractures were evaluated both by conventional views (Waters' and Caldwell views) and coronal CT scans. Conventional views were obtained, as an average, after 4 days and CT after 7 days of injuries. Both the medial wall and the floor were evaluated at two sites, i.e., anterior and posterior. The ethmoid-maxillary plate was also included in the study. The degree of fractures was classified as, no fractures, fractures of discontinuity, dislocation and fragmentation. The coronal CT images in bone window condition was used as reference and the findings were compared between conventional views and CT. The correct diagnosis was obtained as follows: orbital floor (anterior, 78%, posterior, 73%), medial orbital wall (anterior, 72%, posterior, 72%) and ethmoid-maxillary plate (64%). The false positive diagnosis was as follows: orbital floor (anterior only, 13%), medial orbital wall (anterior only, 7%) and ethmoid-maxillary plate (11%). The false negative diagnosis was as follows: orbital floor (anterior, 9%, posterior, 10%), medial orbital wall (anterior, 21%, posterior, 28%) and ethmoid-maxillary plate (21%). The results were compared with those of others in the past. (author)

PREFACE: Domain wall dynamics in nanostructures Domain wall dynamics in nanostructures

Science.gov (United States)

Marrows, C. H.; Meier, G.

2012-01-01

Domain structures in magnetic materials are ubiquitous and have been studied for decades. The walls that separate them are topological defects in the magnetic order parameter and have a wide variety of complex forms. In general, their investigation is difficult in bulk materials since only the domain structure on the surface of a specimen is visible. Cutting the sample to reveal the interior causes a rearrangement of the domains into a new form. As with many other areas of magnetism, the study of domain wall physics has been revitalised by the advent of nanotechnology. The ability to fabricate nanoscale structures has permitted the formation of simplified and controlled domain patterns; the development of advanced microscopy methods has permitted them to be imaged and then modelled; subjecting them to ultrashort field and current pulses has permitted their dynamics to be explored. The latest results from all of these advances are described in this special issue. Not only has this led to results of great scientific beauty, but also to concepts of great applicability to future information technologies. In this issue the reader will find the latest results for these domain wall dynamics and the high-speed processes of topological structures such as domain walls and magnetic vortices. These dynamics can be driven by the application of magnetic fields, or by flowing currents through spintronic devices using the novel physics of spin-transfer torque. This complexity has been studied using a wide variety of experimental techniques at the edge of the spatial and temporal resolution currently available, and can be described using sophisticated analytical theory and computational modelling. As a result, the dynamics can be engineered to give rise to finely controlled memory and logic devices with new functionality. Moreover, the field is moving to study not only the conventional transition metal ferromagnets, but also complex heterostructures, novel magnets and even other

Analytical Study on the Beyond Design Seismic Capacity of Reinforced Concrete Shear Walls

Energy Technology Data Exchange (ETDEWEB)

Nugroho, Tino Sawaldi Adi [Korea Advanced Institute of Science and Technology, Daejeon (Korea, Republic of); Chi, Ho-Seok [Korea Institute of Nuclear Safety, Daejeon (Korea, Republic of)

2015-10-15

The OECD-NEA has organized an international benchmarking program to better understand this critical issue. The benchmark program provides test specimen geometry, test setup, material properties, loading conditions, recorded measures, and observations of the test specimens. The main objective of this research is to assess the beyond design seismic capacity of the reinforced concrete shear walls tested at the European Laboratory for Structural Assessment between 1997 and 1998 through participation in the OECD-NEA benchmark program. In this study, assessing the beyond design seismic capacity of reinforced concrete shear walls is performed analytically by comparing numerical results with experimental results. The seismic shear capacity of the reinforced concrete shear wall was predicted reasonably well using ABAQUS program. However, the proper calibration of the concrete material model was necessary for better prediction of the behavior of the reinforced concrete shear walls since the response was influenced significantly by the material constitutive model.

Regulatory networks, legal federalism, and multi-level regulatory systems

OpenAIRE

Kerber, Wolfgang; Wendel, Julia

2016-01-01

Transnational regulatory networks play important roles in multi-level regulatory regimes, as e.g, the European Union. In this paper we analyze the role of regulatory networks from the perspective of the economic theory of legal federalism. Often sophisticated intermediate institutional solutions between pure centralisation and pure decentralisation can help to solve complex tradeoff problems between the benefits and problems of centralised and decentralised solutions. Drawing upon the insight...

Human Factors Regulatory Research Program Plan, FY 1989--FY 1992

International Nuclear Information System (INIS)

Coffman, F.; Persensky, J.; Ryan, T.; Ramey-Smith, A.; Goodman, C.; Serig, D.; Trager, E; Nuclear Regulatory Commission, Washington, DC; Nuclear Regulatory Commission, Washington, DC; Nuclear Regulatory Commission, Washington, DC

1989-10-01

This report describes the currently ongoing (FY 1989) and planned (FY 1989-1992) Human Factors Regulatory Research Program in the NRC Office of Nuclear Regulatory Research (RES). Examples of the influence of human factors on nuclear safety are presented, and the role of personnel is discussed. Current regulatory issues associated with human factors in the nuclear system and the purpose of the research plan are provided. The report describes the research process applied to the human factors research issues and the program activities: Personnel Performance Measurement, Personnel Subsystem, Human-System Interface. Organization and Management, and Reliability Assessment. The research being conducted within each activity is summarized along with the objectives, background information, and expected regulatory products. Budget and personnel forecasts are provided along with a summary of contractors performing some of the ongoing research. Appendices contain a chronology of human factors research at NRC, a description of the research approach, an update on human factors programs and initiatives in RES and other NRC offices, and the integration among these programs. 46 refs., 5 tabs

International Conference on Effective Nuclear Regulatory Systems: Sustaining Improvements Globally. Book of Abstracts

International Nuclear Information System (INIS)

2016-01-01

The objective of this conference is to review and assess ways of further improving the effectiveness of regulatory systems for nuclear facilities and activities for both nuclear safety and nuclear security. The action items in the summary presented by the President of the conference held in 2013 in Ottawa, the lessons of the Fukushima Daiichi accident, the discussions at other international conferences and at international experts’ meetings conducted within the framework of the IAEA Action Plan on Nuclear Safety, as well as the CNS and the principles outlined in the Vienna Declaration on Nuclear Safety, will continue to have a significant impact on regulatory systems. All the aforementioned need to be taken into account to sustain improvements to regulatory systems. The expected outcomes of the conference are: - Enhanced safety and security of nuclear installations worldwide; - Challenges in regulating radiation sources and radioactive waste addressed; - Enhanced international cooperation for sustaining regulatory effectiveness; - Strengthened and sustained regulatory competence for nuclear safety and security; and - Strategies and actions for the future identified, as well as issues for consideration by governments, regulatory bodies and international organizations.

Quantitative estimation of myocardial thickness by the wall thickness map with Tl-201 myocardial SPECT and its clinical use

International Nuclear Information System (INIS)

Sekiai, Yasuhiro; Sawai, Michihiko; Murayama, Susumu

1988-01-01

To estimate the wall thickness of left ventricular myocardium objectively and quantitatively, we adopted the device of wall thickness map (WTM) with Tl-201 myocardial SPECT. For validation on measuring left ventricular wall thickness with SPECT, fundamental studies were carried out with phantom models, and clinical studies were performed in 10 cases comparing the results from SPECT with those in echocardiography. To draw the WTM, left ventricular wall thickness was measured using the cut off method from SPECT images obtained at 5.6 mm intervals from the base and middle of left ventricle: short-axis image for the base and middle of left ventricle and vertical and horizontal long-axis images for the apical region. Wall thickness was defined from the number of pixel above the cut off level. Results of fundamental studies disclosed that it is impossible to evaluate the thickness of less than 10 mm by Tl-201 myocardial SPECT but possible to discriminate wall thickness of 10 mm, 15 mm, and 20 mm by Tl-201 myocardial SPECT. Echocardiographic results supported the validity of WTM, showing a good linear correlation (r = 0.96) between two methods on measuring wall thickness of left ventricle. We conclude that the WTM applied in this report may be useful for objective and quantitative estimation of myocardial hypertrophy. (author)

Electroweak bubble wall speed limit

Energy Technology Data Exchange (ETDEWEB)

Bödeker, Dietrich [Fakultät für Physik, Universität Bielefeld, 33501 Bielefeld (Germany); Moore, Guy D., E-mail: bodeker@physik.uni-bielefeld.de, E-mail: guymoore@ikp.physik.tu-darmstadt.de [Institut für Kernphysik, Technische Universität Darmstadt, Schlossgartenstraße 2, 64289 Darmstadt (Germany)

2017-05-01

In extensions of the Standard Model with extra scalars, the electroweak phase transition can be very strong, and the bubble walls can be highly relativistic. We revisit our previous argument that electroweak bubble walls can 'run away,' that is, achieve extreme ultrarelativistic velocities γ ∼ 10{sup 14}. We show that, when particles cross the bubble wall, they can emit transition radiation. Wall-frame soft processes, though suppressed by a power of the coupling α, have a significance enhanced by the γ-factor of the wall, limiting wall velocities to γ ∼ 1/α. Though the bubble walls can move at almost the speed of light, they carry an infinitesimal share of the plasma's energy.

Discrimination of Cylinders with Different Wall Thicknesses using Neural Networks and Simulated Dolphin Sonar Signals

DEFF Research Database (Denmark)

Andersen, Lars Nonboe; Au, Whitlow; Larsen, Jan

1999-01-01

This paper describes a method integrating neural networks into a system for recognizing underwater objects. The system is based on a combination of simulated dolphin sonar signals, simulated auditory filters and artificial neural networks. The system is tested on a cylinder wall thickness...... difference experiment and demonstrates high accuracy for small wall thickness differences. Results from the experiment are compared with results obtained by a false killer whale (pseudorca crassidens)....

Improvement of the effectiveness of regulatory management

International Nuclear Information System (INIS)

2001-01-01

The project ARCAL LXVI has as its objective strengthening the national capabilities of the regulatory authorities to achieve an adequate level of radiation safety by training their staff in the implementation of the safety guidelines developed by a prior TC regional project under the framework of the ARCAL Programme and to measure its effectiveness. Detailed program of activities for the years 2001/2002 is presented at this meeting

Objective Self Awareness, Self-Esteem and Causal Attributions for Success and Failure.

Science.gov (United States)

2 (high vs. low self - esteem subjects) design was employed. Objective self -awareness was manipulated by exposing subjects to their image on a wall...The investigation has applied the theory of objective self awareness (Duval and Wicklund, 1972) to the study of causal attributions that actors make...for their past performance. A 2 (male vs. female subject) by 2 (success vs. failure) by 3 (objective self -awareness vs. control vs. time control) by

Safety culture as a matter of regulatory control and regulatory effectiveness

International Nuclear Information System (INIS)

Camargo, C.T.M.; Furieri, E.B.; Arrieta, L.A.I.; Almeida, C.U.C.

2002-01-01

More than 15 years have passed since the term 'safety culture' was introduced by the International Nuclear Safety Advisory Group (INSAG), and although the concept now is widely accepted, practical applications and characteristics have been disseminated mainly for nuclear power plant operating organizations. There is still a lack of international guidance on the use of safety culture as a regulatory matter and on the application of the concept within regulatory organizations. This work explores the meaning of safety culture in two different fields: as an element of safety management systems it shall be a matter of regulatory control; as a complementary tool for quality management it should be used to enhance regulatory effectiveness. Brazilian recent experience on regulating nuclear power reactors provide some examples on how the concept of safety culture may influence regulatory strategies and regulatory management. (author)

Development of an international BRC [Below Regulatory Concern] limit

International Nuclear Information System (INIS)

Kennedy, W.E. Jr.

1987-07-01

The International Atomic Energy Agency (IAEA) has recently investigated the exemption from regulatory control of radiation sources containing limited quantities of radioactive materials. Early efforts were entitled de minimis and were aimed at establishing a philosophical basis and radiation dose limits. The main objectives of more recent work on exemption are to illustrate a method for developing practical radiological criteria, to establish generic criteria, and to determine the practicability of the preliminary exemption principles. The method used to develop the criteria relies on models to evaluate the potential radiation exposure pathways and scenarios for individuals and population groups potentially present following the unrestricted release of materials. This paper describes the assessment methods, presents the generic results expressed in terms of the limiting concentrations of selected radionuclides in municipal waste, and provides a comparison with recent regulatory efforts in the United States for considering selected wastes being Below Regulatory Concern (BRC). 17 refs., 4 tabs

Development of digital library system on regulatory documents for nuclear power plants

International Nuclear Information System (INIS)

Lee, K. H.; Kim, K. J.; Yoon, Y. H.; Kim, M. W.; Lee, J. I.

2001-01-01

The main objective of this study is to establish nuclear regulatory document retrieval system based on internet. With the advancement of internet and information processing technology, information management patterns are going through a new paradigm. Getting along the current of the time, it is general tendency to transfer paper-type documents into electronic-type documents through document scanning and indexing. This system consists of nuclear regulatory documents, nuclear safety documents, digital library, and information system with index and full text

Economic analysis requirements in support of orbital debris regulatory policy

Science.gov (United States)

Greenberg, Joel S.

1996-10-01

As the number of Earth orbiting objects increases so does the potential for generating orbital debris with the consequent increase in the likelihood of impacting and damaging operating satellites. Various debris remediation approaches are being considered that encompass both in-orbit and return-to-Earth schema and have varying degrees of operations, cost, international competitiveness, and safety implications. Because of the diversity of issues, concerns and long-term impacts, there is a clear need for the setting of government policies that will lead to an orderly abatement of the potential orbital debris hazards. These policies may require the establishment of a supportive regulatory regime. The Department of Transportation is likely to have regulatory responsibilities relating to orbital debris stemming from its charge to protect the public health and safety, safety of property, and national security interests and foreign policy interests of the United States. This paper describes DOT's potential regulatory role relating to orbital debris remediation, the myriad of issues concerning the need for establishing government policies relating to orbital debris remediation and their regulatory implications, the proposed technological solutions and their economic and safety implications. Particular emphasis is placed upon addressing cost-effectiveness and economic analyses as they relate to economic impact analysis in support of regulatory impact analysis.

Review of SFR Design Safety using Preliminary Regulatory PSA Model

International Nuclear Information System (INIS)

Na, Hyun Ju; Lee, Yong Suk; Shin, Andong; Suh, Nam Duk

2013-01-01

The major objective of this research is to develop a risk model for regulatory verification of the SFR design, and thereby, make sure that the SFR design is adequate from a risk perspective. In this paper, the development result of preliminary regulatory PSA model of SFR is discussed. In this paper, development and quantification result of preliminary regulatory PSA model of SFR is discussed. It was confirmed that the importance PDRC and ADRC dampers is significant as stated in the result of KAERI PSA model. However, the importance can be changed significantly depending on assumption of CCCG and CCF factor of PDRC and ADRC dampers. SFR (sodium-cooled fast reactor) which is Gen-IV nuclear energy system, is designed to accord with the concept of stability, sustainability and proliferation resistance. KALIMER-600, which is under development in Korea, includes passive safety systems (e. g. passive reactor shutdown, passive residual heat removal, and etc.) as well as active safety systems. Risk analysis from a regulatory perspective is needed to support the regulatory body in its safety and licensing review for SFR (KALIMER-600). Safety issues should be identified in the early design phase in order to prevent the unexpected cost increase and delay of the SFR licensing schedule that may be caused otherwise

The effect of partial poloidal wall sections on the wall stabilization of external kink modes

International Nuclear Information System (INIS)

Ward, D.J.

1996-02-01

An analysis of the effect on the wall stabilization of external kink modes due to toroidally continuous gaps in the resistive wall is performed. The effects with and without toroidal rotation are studied. For a high-β equilibrium, the mode structure is localized on the outboard side. Therefore, outboard gaps greatly increase the growth rate when there is no rotation. For resistive wall stabilization by toroidal rotation, the presence of gaps has the same effect as moving the wall farther away, i.e. destabilizing for the ideal plasma mode, and stabilizing for the resistive wall mode. The region of stability, in terms of wall position, is reduced in size and moved closer to the plasma. However, complete stabilization becomes possible at considerably reduced rotation frequencies. For a high-β, reverse-shear equilibrium both the resistive wall mode and the ideal plasma mode can be stabilized by close fitting discrete passive plates on the outboard side. The necessary toroidal rotation frequency to stabilize the resistive wall mode using these plates is reduced by a factor of three compared to that for a poloidally continuous and complete wall at the same plasma-wall separation. (author) 15 figs., 24 refs

A Structurally Specialized Uniform Wall Layer is Essential for Constructing Wall Ingrowth Papillae in Transfer Cells

Science.gov (United States)

Xia, Xue; Zhang, Hui-Ming; Offler, Christina E.; Patrick, John W.

2017-01-01

Transfer cells are characterized by wall labyrinths with either a flange or reticulate architecture. A literature survey established that reticulate wall ingrowth papillae ubiquitously arise from a modified component of their wall labyrinth, termed the uniform wall layer; a structure absent from flange transfer cells. This finding sparked an investigation of the deposition characteristics and role of the uniform wall layer using a Vicia faba cotyledon culture system. On transfer of cotyledons to culture, their adaxial epidermal cells spontaneously trans-differentiate to a reticulate architecture comparable to their abaxial epidermal transfer cell counterparts formed in planta. Uniform wall layer construction commenced once adaxial epidermal cell expansion had ceased to overlay the original outer periclinal wall on its inner surface. In contrast to the dense ring-like lattice of cellulose microfibrils in the original primary wall, the uniform wall layer was characterized by a sparsely dispersed array of linear cellulose microfibrils. A re-modeled cortical microtubule array exerted no influence on uniform wall layer formation or on its cellulose microfibril organization. Surprisingly, formation of the uniform wall layer was not dependent upon depositing a cellulose scaffold. In contrast, uniform wall cellulose microfibrils were essential precursors for constructing wall ingrowth papillae. On converging to form wall ingrowth papillae, the cellulose microfibril diameters increased 3-fold. This event correlated with up-regulated differential, and transfer-cell specific, expression of VfCesA3B while transcript levels of other cellulose biosynthetic-related genes linked with primary wall construction were substantially down-regulated. PMID:29259611

Sequential injection of domain walls into ferroelectrics at different bias voltages: Paving the way for “domain wall memristors”

Energy Technology Data Exchange (ETDEWEB)

Whyte, J. R.; McQuaid, R. G. P.; Einsle, J. F.; Gregg, J. M., E-mail: m.gregg@qub.ac.uk [Centre for Nanostructured Media (CNM), School of Maths and Physics, Queen' s University Belfast, University Road, Belfast BT7 1NN (United Kingdom); Ashcroft, C. M. [Centre for Nanostructured Media (CNM), School of Maths and Physics, Queen' s University Belfast, University Road, Belfast BT7 1NN (United Kingdom); Department of Physics, Cavendish Laboratory, J. J. Thomson Avenue, Cambridge CB3 0HE (United Kingdom); Canalias, C. [Department of Applied Physics, Royal Institute of Technology, Roslagstullsbacken 21, 10691 Stockholm (Sweden); Gruverman, A. [Department of Physics and Astronomy, University of Nebraska Lincoln, Nebraska 68588–0299 (United States)

2014-08-14

Simple meso-scale capacitor structures have been made by incorporating thin (∼300 nm) single crystal lamellae of KTiOPO{sub 4} (KTP) between two coplanar Pt electrodes. The influence that either patterned protrusions in the electrodes or focused ion beam milled holes in the KTP have on the nucleation of reverse domains during switching was mapped using piezoresponse force microscopy imaging. The objective was to assess whether or not variations in the magnitude of field enhancement at localised “hot-spots,” caused by such patterning, could be used to both control the exact locations and bias voltages at which nucleation events occurred. It was found that both the patterning of electrodes and the milling of various hole geometries into the KTP could allow controlled sequential injection of domain wall pairs at different bias voltages; this capability could have implications for the design and operation of domain wall electronic devices, such as memristors, in the future.

Frequency of left ventricular thrombus after anterior wall st-segment elevation acute myocardial infarction

International Nuclear Information System (INIS)

Iqbal, M.W.; Fayyaz, A.

2014-01-01

Left ventricular thrombus (LVT) formation is a well known complication seen in patients presenting with acute anterior wall ST-segment elevation myocardial infarction (STEMI). In previous studies the incidence of this complication, after acute myocardial infarction (AMI) has been reported to be 4% to 60% in large anterior wall STEMI, depending significantly upon the method as well as time of reperfusion therapy after STEMI. Objective: The objective of this descriptive case series study was to evaluate the frequency of left ventricular thrombus formation in patients after acute anterior wall ST-Segment elevation myocardial infarction. Methodology: In this study, 100 patients with anterior wall STEMI presenting to cardiac emergency or coronary care unit (CCU) of Cardiac complex, Gulab Devi Hospital, were selected on non-probability, purposive sampling meeting inclusion criteria, after taking written informed consent. All the patients were treated initially for management of acute STEMI, including use of thrombolytics where indicated. 2-D Transthoracic echocardiography (TTE) was performed during the same admission to assess presence of LV thrombus (LVT). Results: The mean age of the patients was 54.3 +- 11.4 years. There were 84(84%) male patients and 16 (16%) female patients. LVT was present in 28 (28%) patients on TTE. Among those, there were 23 (82.1%) male and 5 (17.9%) female patients. However, out of 84 male patients 27.4% develop LVT and among 16 female patients this ratio was 31.3%. The LV thrombus was independent of age and gender. LV thrombus was significantly less in thrombolytic group as compared to those who were not given this therapy, i.e. p value <0.05. Conclusion: Patients with anterior wall acute STEMI not infrequently develop the complication of development of LV thrombus. In this study the frequency of LV thrombus formation after anterior wall acute STEMI was 28%. (author)

Conceptual Design and Feasibility Analyses of a Robotic System for Automated Exterior Wall Painting

Directory of Open Access Journals (Sweden)

Young S. Kim

2008-11-01

Full Text Available There are approximately 6,677,000 apartment housing units in South Korea. Exterior wall painting for such multi-dwelling apartment housings in South Korea represents a typical area to which construction automation technology can be applied for improvement in safety, productivity, quality, and cost over the conventional method. The conventional exterior wall painting is costly and labor-intensive, and it especially exposes workers to significant health and safety risks. The primary objective of this study is to design a conceptual model of an exterior wall painting robot which is applicable to apartment housing construction and maintenance, and to conduct its technical?economical feasibility analyses. In this study, a design concept using a high ladder truck is proposed as the best alternative for automation of the exterior wall painting. Conclusions made in this study show that the proposed exterior wall painting robot is technically and economically feasible, and can greatly enhance safety, productivity, and quality compared to the conventional method. Finally, it is expected that the conceptual model of the exterior wall painting robot would be efficiently used in various applications in exterior wall finishing and maintenance of other architectural and civil structures such as commercial buildings, towers, and high-rise storage tanks.

Shear localization and effective wall friction in a wall bounded granular flow

Science.gov (United States)

Artoni, Riccardo; Richard, Patrick

2017-06-01

In this work, granular flow rheology is investigated by means of discrete numerical simulations of a torsional, cylindrical shear cell. Firstly, we focus on azimuthal velocity profiles and study the effect of (i) the confining pressure, (ii) the particle-wall friction coefficient, (iii) the rotating velocity of the bottom wall and (iv) the cell diameter. For small cell diameters, azimuthal velocity profiles are nearly auto-similar, i.e. they are almost linear with the radial coordinate. Different strain localization regimes are observed : shear can be localized at the bottom, at the top of the shear cell, or it can be even quite distributed. This behavior originates from the competition between dissipation at the sidewalls and dissipation in the bulk of the system. Then we study the effective friction at the cylindrical wall, and point out the strong link between wall friction, slip and fluctuations of forces and velocities. Even if the system is globally below the sliding threshold, force fluctuations trigger slip events, leading to a nonzero wall slip velocity and an effective wall friction coefficient different from the particle-wall one. A scaling law was found linking slip velocity, granular temperature in the main flow direction and effective friction. Our results suggest that fluctuations are an important ingredient for theories aiming to capture the interface rheology of granular materials.

Improvement of quality of 3D printed objects by elimination of microscopic structural defects in fused deposition modeling.

Directory of Open Access Journals (Sweden)

Evgeniy G Gordeev

Full Text Available Additive manufacturing with fused deposition modeling (FDM is currently optimized for a wide range of research and commercial applications. The major disadvantage of FDM-created products is their low quality and structural defects (porosity, which impose an obstacle to utilizing them in functional prototyping and direct digital manufacturing of objects intended to contact with gases and liquids. This article describes a simple and efficient approach for assessing the quality of 3D printed objects. Using this approach it was shown that the wall permeability of a printed object depends on its geometric shape and is gradually reduced in a following series: cylinder > cube > pyramid > sphere > cone. Filament feed rate, wall geometry and G-code-defined wall structure were found as primary parameters that influence the quality of 3D-printed products. Optimization of these parameters led to an overall increase in quality and improvement of sealing properties. It was demonstrated that high quality of 3D printed objects can be achieved using routinely available printers and standard filaments.

Optimization of Steady Wall Temperature for Disturbance Control

OpenAIRE

Pralits, Jan; Ardeshir, Hanifi

2003-01-01

We present a theory for computing the optimal steady wall temperature distribution to suppress the growth of convectively unstable disturbances in compressible boundary layer flows on flat plates. A gradient based iterative procedure is used to minimize an objective function measuring the disturbance kinetic energy. The gradient of interest is obtained from the solution of the adjoint of the boundary layer and parabolized stability equations, which are derived using a Lagrange multiplier tech...

Numerical analysis for the optimal location of a thin PCM layer in frame walls

International Nuclear Information System (INIS)

Jin, Xing; Medina, Mario A.; Zhang, Xiaosong

2016-01-01

Highlights: • The optimal PCM location was estimated by a mathematical model. • The optimal PCM location was affected by the properties of PCM. • The optimal PCM location was affected by the environmental conditions. - Abstract: The thermal performance of building walls can be improved using phase change materials (PCMs). The objective of this study was to estimate the optimal location of a “thin” PCM layer to be incorporated into frame walls, parallel to the frame and insulation, for the purpose of increasing thermal mass and reducing peak heat fluxes through the wall. Based on a mathematical model built in this paper, it was found that an optimal location of this “thin” PCM layer can be estimated, and it was affected by the thermal properties of PCM and the environmental conditions. The optimal locations for the PCM layer were found to be closer to the exterior surface of the wall when the thickness of PCM layer, the heat of fusion of PCM, and the PCM melting temperature were increased, while the optimal location was closer to the interior surface of the wall when the interior surface temperature of the wall was increased.

76 FR 21932 - Self-Regulatory Organizations; Financial Industry Regulatory Authority, Inc.; Order Granting...

Science.gov (United States)

2011-04-19

... statement therein, as follows: I. Introduction On February 4, 2011, the Financial Industry Regulatory...-Regulatory Organizations; Financial Industry Regulatory Authority, Inc.; Order Granting Approval of a... Financial Industry Regulatory Authority, Inc. (``FINRA'') to amend Rule 13806 of the Code of Arbitration...

Enzymes in biogenesis of plant cell wall polysaccharides. Enzyme characterization using tracer techniques

International Nuclear Information System (INIS)

Dickinson, D.B.

1975-01-01

Enzymes and metabolic pathways, by which starch and cell wall polysaccharides are formed, were investigated in order to learn how these processes are regulated and to identify the enzymatic regulatory mechanisms involved. Germinating lily pollen was used for studies of cell wall formation, and pollen and maize endosperm for studies of starch biosynthesis. Hexokinase being the first step in conversion of hexoses to starch, wall polysaccharides and respiratory substrates, maize endosperm enzyme was assayed by its conversion of 14 C-hexose to 14 C-hexose-6-P, and rapid separation of the two labelled compounds on anion-exchange paper. This enzyme did not appear to be under tight regulation by feed-back inhibition or activation, nor to be severely inhibited by glucose-6-P or activated by citrate. ADP-glucose pyrophosphorylase and other pyrophosphorylases were assayed radiochemically with 14 C-glucose-1-P (forward direction) or 32-PPsub(i) (reverse direction). They showed that the maize endosperm enzyme was activated by the glycolytic intermediates fructose-6-P and 3-phosphoglycerate, and that low levels of the enzyme were present in the high sucrose-low starch mutant named shrunken-2. Under optimal in-vitro assay conditions, the pollen enzyme reacted four times faster than the observed in-vivo rate of starch accumulation. Biogenesis of plant cell wall polysaccharides requires the conversion of hexose phosphates to various sugar nucleotides and utilization of the latter by the appropriate polysaccharide synthetases. Lily pollen possesses a β-1,3-glucan synthetase which is activated up to six-fold by β-linked oligosaccharides. Hence, the in-vivo activity of this enzyme may be modulated by such effector molecules

Application of the LBB regulatory approach to the steamlines of advanced WWER 1000 reactor

Energy Technology Data Exchange (ETDEWEB)

Kiselyov, V.A.; Sokov, L.M.

1997-04-01

The LBB regulatory approach adopted in Russia in 1993 as an extra safety barrier is described for advanced WWER 1000 reactor steamline. The application of LBB concept requires the following additional protections. First, the steamline should be a highly qualified piping, performed in accordance with the applicable regulations and guidelines, carefully screened to verify that it is not subjected to any disqualifying failure mechanism. Second, a deterministic fracture mechanics analysis and leak rate evaluation have been performed to demonstrate that postulated through-wall crack that yields 95 1/min at normal operation conditions is stable even under seismic loads. Finally, it has been verified that the leak detection systems are sufficiently reliable, diverse and sensitive, and that adequate margins exist to detect a through wall crack smaller than the critical size. The obtained results are encouraging and show the possibility of the application of the LBB case to the steamline of advanced WWER 1000 reactor.

Application of the LBB regulatory approach to the steamlines of advanced WWER 1000 reactor

International Nuclear Information System (INIS)

Kiselyov, V.A.; Sokov, L.M.

1997-01-01

The LBB regulatory approach adopted in Russia in 1993 as an extra safety barrier is described for advanced WWER 1000 reactor steamline. The application of LBB concept requires the following additional protections. First, the steamline should be a highly qualified piping, performed in accordance with the applicable regulations and guidelines, carefully screened to verify that it is not subjected to any disqualifying failure mechanism. Second, a deterministic fracture mechanics analysis and leak rate evaluation have been performed to demonstrate that postulated through-wall crack that yields 95 1/min at normal operation conditions is stable even under seismic loads. Finally, it has been verified that the leak detection systems are sufficiently reliable, diverse and sensitive, and that adequate margins exist to detect a through wall crack smaller than the critical size. The obtained results are encouraging and show the possibility of the application of the LBB case to the steamline of advanced WWER 1000 reactor

The role of wall calcium in the extension of cell walls of soybean hypocotyls

Science.gov (United States)

Virk, S. S.; Cleland, R. E.

1990-01-01

Calcium crosslinks are load-bearing bonds in soybean (Glycine max (L.) Merr.) hypocotyl cell walls, but they are not the same load-bearing bonds that are broken during acid-mediated cell elongation. This conclusion is reached by studying the relationship between wall calcium, pH and the facilitated creep of frozen-thawed soybean hypocotyl sections. Supporting data include the following observations: 1) 2-[(2-bis-[carboxymethyl]amino-5-methylphenoxy)methyl]-6-methoxy-8-bis[car boxymethyl]aminoquinoline (Quin 2) and ethylene glycol-bis(2-aminoethyl ether)-N,N,N',N'-tetraacetic acid (EGTA) caused only limited facilitated creep as compared with acid, despite removal of comparable or larger amounts of wall calcium; 2) the pH-response curves for calcium removal and acid-facilitated creep were different; 3) reversible acid-extension occurred even after removal of almost all wall calcium with Quin 2; and 4) growth of abraded sections did not involve a proportional loss of wall calcium. Removal of wall calcium, however, increased the capacity of the walls to undergo acid-facilitated creep. These data indicate that breakage of calcium crosslinks is not a major mechanism of cell-wall loosening in soybean hypocotyl tissues.

Traumatic abdominal wall hernia - four cases and a review of the ...

African Journals Online (AJOL)

Objective: To review blunt traumatic abdominal wall hernias (TAWHs) in our institution. Method: Retrospective review of blunt abdominal trauma cases over a 6-month period. Results: Four patients with TAWH were identified. The mean age was 36 years. Three had been involved in vehicular collisions, and 1 had been ...

Systematisation of the use of experience feedback from NPP's in the regulatory field

International Nuclear Information System (INIS)

Vandewalle, A.

2004-01-01

Operating experience activities are important to maintain and to improve nuclear safety for nuclear power plant installations. Although with somewhat other objectives, the same kind of activities has to be performed by the regulatory organisations to support their functions, responsibilities and missions, without duplications and wastage of resources. International cooperation to share experience gained from events is also essential in this improvement process and each regulatory organisation should participate to this fundamental support to nuclear safety. (orig.)

Granular packings with moving side walls

International Nuclear Information System (INIS)

Landry, James W.; Grest, Gary Stephen

2004-01-01

The effects of movement of the side walls of a confined granular packing are studied by discrete element, molecular dynamics simulations. The dynamical evolution of the stress is studied as a function of wall movement both in the direction of gravity as well as opposite to it. For all wall velocities explored, the stress in the final state of the system after wall movement is fundamentally different from the original state obtained by pouring particles into the container and letting them settle under the influence of gravity. The original packing possesses a hydrostaticlike region at the top of the container which crosses over to a depth-independent stress. As the walls are moved in the direction opposite to gravity, the saturation stress first reaches a minimum value independent of the wall velocity, then increases to a steady-state value dependent on the wall velocity. After wall movement ceases and the packing reaches equilibrium, the stress profile fits the classic Janssen form for high wall velocities, while some deviations remain for low wall velocities. The wall movement greatly increases the number of particle-wall and particle-particle forces at the Coulomb criterion. Varying the wall velocity has only small effects on the particle structure of the final packing so long as the walls travel a similar distance.

Leveraging network utility management practices for regulatory purposes

International Nuclear Information System (INIS)

2009-11-01

Electric utilities around the globe are entering a phase where they must modernize and implement smart grid technologies. In order to optimize system architecture, asset replacement, and future operating costs, it the utilities must implement robust and flexible asset management structures. This report discussed the ways in which regulators assess investment plans. It focused on the implicit or explicit use of an asset management approach, including principles; processes; input and outputs; decision-making criteria and prioritization methods. The Ontario Energy Board staff were familiarized with the principles and objectives of established and emerging asset management processes and underlying analytic processes, systems and tools in order to ensure that investment information provided by network utilities regarding rates and other applications could be evaluated effectively. Specifically, the report discussed the need for and importance of asset management and provided further details of international markets and their regulatory approaches to asset management. The report also discussed regulatory approaches for review of asset management underlying investment plans as well as an overview of international regulatory practice for review of network utility asset management. It was concluded that options for strengthening regulatory guidance and assessment included utilizing appropriate and effective benchmarking to assess, promote and provide incentives for best practices and steer clear of the potential perverse incentives. 21 tabs., 17 figs., 1 appendix.

Plasma-wall interactions

International Nuclear Information System (INIS)

Behrisch, Rainer

1978-01-01

The plasma wall interactions for two extreme cases, the 'vacuum model' and the 'cold gas blanket' are outlined. As a first step for understanding the plasma wall interactions the elementary interaction processes at the first wall are identified. These are energetic ion and neutral particle trapping and release, ion and neutral backscattering, ion sputtering, desorption by ions, photons and electrons and evaporation. These processes have only recently been started to be investigated in the parameter range of interest for fusion research. The few measured data and their extrapolation into regions not yet investigated are reviewed

Combined aerobic and resistance exercise training decreases peripheral but not central artery wall thickness in subjects with type 2 diabetes.

NARCIS (Netherlands)

Schreuder, T.H.A.; Munckhof, I.C.L. van den; Poelkens, F.; Hopman, M.T.; Thijssen, D.H.

2015-01-01

OBJECTIVE: Little is known about the impact of exercise training on conduit artery wall thickness in type 2 diabetes. We examined the local and systemic impact of exercise training on superficial femoral (SFA), brachial (BA), and carotid artery (CA) wall thickness in type 2 diabetes patients and

Argentina's regulatory body: its communication activities

International Nuclear Information System (INIS)

Cesario, Pablo A.; Terigi, Gabriel E.

2008-01-01

Full text: The Nuclear Regulatory Authority of Argentina (ARN) is empowered to regulate and control the nuclear activity with regard to radiation and nuclear safety, physical protection and nuclear non-proliferation issues. It must also advise the Executive on issues under its purview. The objective of the Nuclear Regulatory Authority is to establish, develop and enforce a regulatory system applicable to all nuclear activities carried out in Argentina. Two of the goals of this regulatory system are to provide an appropriate standard of protection for individuals against the harmful effects of ionizing radiation, and to maintain a reasonable degree of radiological and nuclear safety in the nuclear activities performed in Argentina. The responsibility of the radiation protection community in performing the tasks to accomplish this goals is twofold. On one hand, it must ensure a high technical quality in performing these functions. It must also provide information on its activities which has to be accurate, comprehensive and understandable. The way a society understands the concept of 'risk' needs to be kept in mind. Risk perception is the subjective judgment that people make about the characteristics and severity of a risk. Cultural theory refers to theories of risk perception that focus on culture, rather than individual psychology as an explanation for differences in risk judgments. It is widely agreed that trust is a key factor in influencing people's perceptions of risk. It is understood there are two main ways trust may impact in risk perceptions: an activity is perceived as more risky if the people or agencies managing it are perceived as untrustworthy; and information presented by trusted sources is given more credibility than information from untrusted sources. One of the primary purposes of ARN's Communication Program is to provide a means whereby those engaged in radiation protection activities may communicate more readily with each other and the public and

The Bacillus subtilis GntR family repressor YtrA responds to cell wall antibiotics.

Science.gov (United States)

Salzberg, Letal I; Luo, Yun; Hachmann, Anna-Barbara; Mascher, Thorsten; Helmann, John D

2011-10-01

The transglycosylation step of cell wall synthesis is a prime antibiotic target because it is essential and specific to bacteria. Two antibiotics, ramoplanin and moenomycin, target this step by binding to the substrate lipid II and the transglycosylase enzyme, respectively. Here, we compare the ramoplanin and moenomycin stimulons in the Gram-positive model organism Bacillus subtilis. Ramoplanin strongly induces the LiaRS two-component regulatory system, while moenomycin almost exclusively induces genes that are part of the regulon of the extracytoplasmic function (ECF) σ factor σ(M). Ramoplanin additionally induces the ytrABCDEF and ywoBCD operons, which are not part of a previously characterized antibiotic-responsive regulon. Cluster analysis reveals that these two operons are selectively induced by a subset of cell wall antibiotics that inhibit lipid II function or recycling. Repression of both operons requires YtrA, which recognizes an inverted repeat in front of its own operon and in front of ywoB. These results suggest that YtrA is an additional regulator of cell envelope stress responses.

Enhanced wall pumping in JET

International Nuclear Information System (INIS)

Ehrenberg, J.; Harbour, P.J.

1991-01-01

The enhanced wall pumping phenomenon in JET is observed for hydrogen or deuterium plasmas which are moved from the outer (larger major radius) limiter position either to the inner wall or to the top/bottom wall of the vacuum vessel. This phenomenon is analysed by employing a particle recycling model which combines plasma particle transport with particle re-emission from and retention within material surfaces. The model calculates the important experimentally observable quantities, such as particle fluxes, global particle confinement time, plasma density and density profile. Good qualitative agreement is found and, within the uncertainties, the agreement is quantitative if the wall pumping is assumed to be caused by two simultaneously occurring effects: (1) Neutral particle screening at the inner wall and the top/bottom wall is larger than that at the outer limiter because of different magnetic topologies at different poloidal positions; and (2) although most of the particles (≥ 90%) impacting on the wall can be promptly re-emitted, a small fraction (≤ 10%) of them must be retained in the wall for a period of time which is similar to or larger than the global plasma particle confinement time. However, the wall particle retention time need not be different from that of the outer limiter, i.e. pumping can occur when there is no difference between the material properties of the limiter and those of the wall. (author). 45 refs, 18 figs

Fuel retention under elevated wall temperature in KSTAR with a carbon wall

Science.gov (United States)

Cao, B.; Hong, S. H.

2018-03-01

The fuel retention during KSTAR discharges with elevated wall temperature (150 °C) has been studied by using the method of global particle balance. The results show that the elevated wall temperature could reduce the dynamic retention via implantation and absorption, especially for the short pulse shots with large injected fuel particles. There is no signature changing of long-term retention, which related to co-deposition, under elevated wall temperature. For soft-landing shots (normal shots), the exhausted fuel particles during discharges is larger with elevated wall temperature than without, but the exhausted particles after discharges within 90 s looks similar. The outgassing particles because of disruption could be exhausted within 15 s.

New Methods for Imaging Evaluation of Chest Wall Deformities

Directory of Open Access Journals (Sweden)

Ana Lain

2017-12-01

Full Text Available AimThe purpose of this study is to describe the development of an external 3-dimensional (3D scanner as a noninvasive method for imaging chest wall deformities. It allows objective assessment, reconstruction of the area of interest, and evaluation of the severity of the deformity by using external indexes.External 3D scanning systemThe OrtenBodyOne scanner (Orten, Lyon, France uses depth sensors to scan the entire 3D external body surface of a patient. The depth sensors combine structured light with two classic computer vision techniques: depth from focus and depth from stereo. The data acquired are processed and analyzed using the Orten-Clinic software.Materials and methodsTo investigate the performance of the device, a preliminary prospective study (January 2015–March 2016 was carried out in patients attending our hospital chest wall deformities unit. In total, 100 patients (children and young adults with pectus excavatum or pectus carinatum, treated by surgery or non-operative methods were included. In patients undergoing non-operative treatment, external 3D scanning was performed monthly until complete correction was achieved. In surgically treated patients, scanning was done before and after surgical correction. In 42 patients, computed tomography (CT was additionally performed and correlations between the Haller index calculated by CT and the external Haller index using external scanning were investigated using a Student’s test (r = 0.83.ConclusionExternal scanning is an effective, objective, radiation-free means to diagnose and follow-up patients with chest wall deformities. Externally measured indexes can be used to evaluate the severity of these conditions and the treatment outcomes.

Serviceability limit state related to excessive lateral deformations to account for infill walls in the structural model

Directory of Open Access Journals (Sweden)

G. M. S. ALVA

Full Text Available Brazilian Codes NBR 6118 and NBR 15575 provide practical values for interstory drift limits applied to conventional modeling in order to prevent negative effects in masonry infill walls caused by excessive lateral deformability, however these codes do not account for infill walls in the structural model. The inclusion of infill walls in the proposed model allows for a quantitative evaluation of structural stresses in these walls and an assessment of cracking in these elements (sliding shear diagonal tension and diagonal compression cracking. This paper presents the results of simulations of single-story one-bay infilled R/C frames. The main objective is to show how to check the serviceability limit states under lateral loads when the infill walls are included in the modeling. The results of numerical simulations allowed for an evaluation of stresses and the probable cracking pattern in infill walls. The results also allowed an identification of some advantages and limitations of the NBR 6118 practical procedure based on interstory drift limits.

Regulation of Telecommunications: The Choice Between Market and Regulatory Failures

Directory of Open Access Journals (Sweden)

Dmitrii Trubnikov

2017-04-01

Full Text Available Purpose – The paper examines the main regulatory frameworks of the telecommunications industry through the concept of market failure and analyses how and why the policy often leads to undesirable outcomes that might be considered as regulatory failure. Methodology/approach/design – The research uses the EU regulatory framework for electronic communications as a base for the analysis of the main policy objectives through the prism of the market failure theory with an eye to the interests of the main market players in the telecommunications markets. Findings – About any aspect of regulation allows to find ways to create opportunities for some groups of the industry and stifle activity of others. Despite the theory of market failure provides reasonable justifications for regulation of telecommunications markets, it is possible to argue that many of these problems are mainly the consequence of the policy and could be better solved by market mechanisms. Originality/value – The results of the research allow to look at the problems of telecommunications development and issues of the high level of concentration of the telecommunications markets as regulatory formed problems rather than consequences of the inherited industry’s characteristics.

Needs of research for regulatory purposes

International Nuclear Information System (INIS)

Wanner, H.

2010-01-01

question whether or not it is the duty of the regulator to carry out such complementary work is the subject of controversial discussions. A further issue is the source of the budget from which research for regulatory purposes should be funded since frequent sources of funding are the waste producers and the national budgets. The question of how much regulatory research is needed is difficult to answer on a general basis. It appears obvious that the regulator must achieve the objectives of competence and independence. The research needed for this purpose is the least the regulator must undertake. The verification of key safety issues and the investigation of issues not addressed by the implementer may be considered as optional

International Divider Walls

NARCIS (Netherlands)

Kruis, A.; Sneller, Lineke

2013-01-01

The subject of this teaching case is the Enterprise Resource Planning (ERP) system implementation at International Divider Walls, the world market leader in design, production, and sales of divider walls. The implementation in one of the divisions of this multinational company had been successful,

Aspergillus fumigatus Cell Wall α-(1,3)-Glucan Stimulates Regulatory T-Cell Polarization by Inducing PD-L1 Expression on Human Dendritic Cells.

Science.gov (United States)

Stephen-Victor, Emmanuel; Karnam, Anupama; Fontaine, Thierry; Beauvais, Anne; Das, Mrinmoy; Hegde, Pushpa; Prakhar, Praveen; Holla, Sahana; Balaji, Kithiganahalli N; Kaveri, Srini V; Latgé, Jean-Paul; Aimanianda, Vishukumar; Bayry, Jagadeesh

2017-12-05

Human dendritic cell (DC) response to α-(1,3)-glucan polysaccharide of Aspergillus fumigatus and ensuing CD4+ T-cell polarization are poorly characterized. α-(1,3)-Glucan was isolated from A. fumigatus conidia and mycelia cell wall. For the analysis of polarization, DCs and autologous naive CD4+ T cells were cocultured. Phenotype of immune cells was analyzed by flow cytometry, and cytokines by enzyme-linked immunosorbent assay (ELISA). Blocking antibodies were used to dissect the role of Toll-like receptor 2 (TLR2) and programmed death-ligand 1 (PD-L1) in regulating α-(1,3)-glucan-mediated DC activation and T-cell responses. DCs from TLR2-deficient mice were additionally used to consolidate the findings. α-(1,3)-Glucan induced the maturation of DCs and was dependent in part on TLR2. "α-(1,3)-Glucan-educated" DCs stimulated the activation of naive T cells and polarized a subset of these cells into CD4+CD25+FoxP3+ regulatory T cells (Tregs). Mechanistically, Treg stimulation by α-(1,3)-glucan was dependent on the PD-L1 pathway that negatively regulated interferon-gamma (IFN-γ) secretion. Short α-(1,3)-oligosaccharides lacked the capacity to induce maturation of DCs but significantly blocked α-(1,3)-glucan-induced Treg polarization. PD-L1 dictates the balance between Treg and IFN-γ responses induced by α-(1,3)-glucan. Our data provide a rationale for the exploitation of immunotherapeutic approaches that target PD-1-PD-L1 to enhance protective immune responses to A. fumigatus infections. © The Author 2017. Published by Oxford University Press for the Infectious Diseases Society of America. All rights reserved. For permissions, e-mail: journals.permissions@oup.com.

e-Communications: Investment and the Regulatory Framework

OpenAIRE

Jones, Siôn; Jones, Pau

2006-01-01

The EU regulatory framework for e-communications was adopted by the European Parliament and the Council in 2002, and became applicable from 2003. It has three primary objectives: (1) to promote competition; (2) to develop the single market; and (3) to promote citizens' rights. The European Commission's DG Information Society commissioned London Economics to estimate the level of e-communications investment in the EU and to examine its main drivers as part of a contributio to the Commission's...

Wall Street som kreationistisk forkynder

DEFF Research Database (Denmark)

Ekman, Susanne

2016-01-01

Artiklen gennemgår Karen Hos etnografi om Wall Street: "Liquidated: An ethnography of Wall Street" set i lyset af den offentlige debat vedrørende Goldman Sachs opkøb af Dong......Artiklen gennemgår Karen Hos etnografi om Wall Street: "Liquidated: An ethnography of Wall Street" set i lyset af den offentlige debat vedrørende Goldman Sachs opkøb af Dong...

A black body absorber from vertically aligned single-walled carbon nanotubes

Science.gov (United States)

Mizuno, Kohei; Ishii, Juntaro; Kishida, Hideo; Hayamizu, Yuhei; Yasuda, Satoshi; Futaba, Don N.; Yumura, Motoo; Hata, Kenji

2009-01-01

Among all known materials, we found that a forest of vertically aligned single-walled carbon nanotubes behaves most similarly to a black body, a theoretical material that absorbs all incident light. A requirement for an object to behave as a black body is to perfectly absorb light of all wavelengths. This important feature has not been observed for real materials because materials intrinsically have specific absorption bands because of their structure and composition. We found a material that can absorb light almost perfectly across a very wide spectral range (0.2–200 μm). We attribute this black body behavior to stem from the sparseness and imperfect alignment of the vertical single-walled carbon nanotubes. PMID:19339498

Assessment of short through-wall circumferential cracks in pipes. Experiments and analysis: March 1990--December 1994

Energy Technology Data Exchange (ETDEWEB)

Brust, F.W.; Scott, P.; Rahman, S. [Battelle, Columbus, OH (United States)] [and others

1995-04-01

This topical report summarizes the work performed for the Nuclear Regulatory Commission`s (NRC) research program entitled ``Short Cracks in Piping and Piping Welds`` that specifically focuses on pipes with short through-wall cracks. Previous NRC efforts, conducted under the Degraded Piping Program, focused on understanding the fracture behavior of larger cracks in piping and fundamental fracture mechanics developments necessary for this technology. This report gives details on: (1) material property determinations, (2) pipe fracture experiments, and (3) development, modification, and validation of fracture analysis methods. The material property data required to analyze the experimental results are included. These data were also implemented into the NRC`s PIFRAC database. Three pipe experiments with short through-wall cracks were conducted on large diameter pipe. Also, experiments were conducted on a large-diameter uncracked pipe and a pipe with a moderate-size through-wall crack. The analysis results reported here focus on simple predictive methods based on the J-Tearing theory as well as limit-load and ASME Section 11 analyses. Some of these methods were improved for short-crack-length predictions. The accuracy of the various methods was determined by comparisons with experimental results from this and other programs. 69 refs., 124 figs, 49 tabs.

Assessment of short through-wall circumferential cracks in pipes. Experiments and analysis: March 1990--December 1994

International Nuclear Information System (INIS)

Brust, F.W.; Scott, P.; Rahman, S.

1995-04-01

This topical report summarizes the work performed for the Nuclear Regulatory Commission's (NRC) research program entitled ''Short Cracks in Piping and Piping Welds'' that specifically focuses on pipes with short through-wall cracks. Previous NRC efforts, conducted under the Degraded Piping Program, focused on understanding the fracture behavior of larger cracks in piping and fundamental fracture mechanics developments necessary for this technology. This report gives details on: (1) material property determinations, (2) pipe fracture experiments, and (3) development, modification, and validation of fracture analysis methods. The material property data required to analyze the experimental results are included. These data were also implemented into the NRC's PIFRAC database. Three pipe experiments with short through-wall cracks were conducted on large diameter pipe. Also, experiments were conducted on a large-diameter uncracked pipe and a pipe with a moderate-size through-wall crack. The analysis results reported here focus on simple predictive methods based on the J-Tearing theory as well as limit-load and ASME Section 11 analyses. Some of these methods were improved for short-crack-length predictions. The accuracy of the various methods was determined by comparisons with experimental results from this and other programs. 69 refs., 124 figs, 49 tabs

Observations on resistive wall modes

International Nuclear Information System (INIS)

Gerwin, R.A.; Finn, J.M.

1996-01-01

Several results on resistive wall modes and their application to tokamaks are presented. First, it is observed that in the presence of collisional parallel dynamics there is an exact cancellation to lowest order of the dissipative and sound wave effects for an ideal Ohm's law. This is easily traced to the fact that the parallel dynamics occurs along the perturbed magnetic field lines for such electromagnetic modes. Such a cancellation does not occur in the resistive layer of a tearing-like mode. The relevance to models for resistive wall modes using an electrostatic Hammett-Perkins type operator to model Landau damping will be discussed. Second, we observe that with an ideal Ohm's law, resistive wall modes can be destabilized by rotation in that part of parameter space in which the ideal MHD modes are stable with the wall at infinity. This effect can easily be explained by interpreting the resistive wall instability in terms of mode coupling between the backward stable MHD mode and a stable mode locked into the wall. Such an effect can occur for very small rotation for tearing-resistive wall modes in which inertia dominates viscosity in the layer, but the mode is stabilized by further rotation. For modes for which viscosity dominates in the layer, rotation is purely stabilizing. For both tearing models, a somewhat higher rotation frequency gives stability essentially whenever the tearing mode is stable with a perfectly conducting wall. These tearing/resistive wall results axe also simply explained in terms of mode coupling. It has been shown that resonant external ideal modes can be stabilized in the presence of resistive wall and resistive plasma with rotation of order the nominal tearing mode growth rate. We show that these modes behave as resistive wall tearing modes in the sense above. This strengthens the suggestion that rotational stabilization of the external kink with a resistive wall is due to the presence of resistive layers, even for ideal modes

75 FR 11166 - Joint Meeting of the Nuclear Regulatory Commission and the Federal Energy Regulatory Commission...

Science.gov (United States)

2010-03-10

... the Nuclear Regulatory Commission and the Federal Energy Regulatory Commission; Notice of Joint Meeting of the Nuclear Regulatory Commission and the Federal Energy Regulatory Commission March 2, 2010. The Federal Energy Regulatory Commission (FERC) and the Nuclear Regulatory Commission (NRC) will hold...

Supersymmetric domain walls

NARCIS (Netherlands)

Bergshoeff, Eric A.; Kleinschmidt, Axel; Riccioni, Fabio

2012-01-01

We classify the half-supersymmetric "domain walls," i.e., branes of codimension one, in toroidally compactified IIA/IIB string theory and show to which gauged supergravity theory each of these domain walls belong. We use as input the requirement of supersymmetric Wess-Zumino terms, the properties of

Abdominal wall blocks in adults

DEFF Research Database (Denmark)

Børglum, Jens; Gögenür, Ismail; Bendtsen, Thomas F

2016-01-01

been introduced with success. Future research should also investigate the effect of specific abdominal wall blocks on neuroendocrine and inflammatory stress response after surgery.  Summary USG abdominal wall blocks in adults are commonplace techniques today. Most abdominal wall blocks are assigned......Purpose of review Abdominal wall blocks in adults have evolved much during the last decade; that is, particularly with the introduction of ultrasound-guided (USG) blocks. This review highlights recent advances of block techniques within this field and proposes directions for future research.......  Recent findings Ultrasound guidance is now considered the golden standard for abdominal wall blocks in adults, even though some landmark-based blocks are still being investigated. The efficiency of USG transversus abdominis plane blocks in relation to many surgical procedures involving the abdominal wall...

Near-Wall Turbulence Modelling of Rotating and Curved Shear Flows

Energy Technology Data Exchange (ETDEWEB)

Pettersson, Bjoern Anders

1997-12-31

This thesis deals with verification and refinement of turbulence models within the framework of the Reynolds-averaged approach. It pays special attention to modelling the near-wall region, where the turbulence is strongly non-homogeneous and anisotropic. It also studies in detail the effects associated with an imposed rotation of the reference frame or streamline curvature. The objective with near-wall turbulence closure modelling is to formulate a set of equations governing single point turbulence statistics, which can be solved in the region of the flow which extends to the wall. This is in contrast to the commonly adopted wall-function approach in which the wall-boundary conditions are replaced by matching conditions in the logarithmic region. The near-wall models allow more flexibility by not requiring any such universal behaviour. Assessment of the novel elliptic relaxation approach to model the proximity of a solid boundary reveals an encouraging potential used in conjunction with second-moment and eddy-viscosity closures. The most natural level of closure modelling to predict flows affected by streamline curvatures or an imposed rotation of the reference frame is at the second-moment closure (SMC) level. Although SMCs naturally accounts for the effects of system rotation, the usual application of a scalar dissipation rate equation is shown to require ad hoc corrections in some cases in order to give good results. The elliptic relaxation approach is also used in conjunction with non-linear pressure-strain models and very encouraging results are obtained for rotating flows. Rotational induced secondary motions are vital to predicting the effects of system rotation. Some severe weaknesses of non-linear pressure-strain models are also indicated. Finally, a modelling methodology for anisotropic dissipation in nearly homogeneous turbulence are proposed. 84 refs., 56 figs., 16 tabs.

Seismic Behaviour of Composite Steel Fibre Reinforced Concrete Shear Walls

Science.gov (United States)

Boita, Ioana-Emanuela; Dan, Daniel; Stoian, Valeriu

2017-10-01

In this paper is presented an experimental study conducted at the “Politehnica” University of Timisoara, Romania. This study provides results from a comprehensive experimental investigation on the behaviour of composite steel fibre reinforced concrete shear walls (CSFRCW) with partially or totally encased profiles. Two experimental composite steel fibre reinforced concrete walls (CSFRCW) and, as a reference specimen, a typical reinforced concrete shear wall (RCW), (without structural reinforcement), were fabricated and tested under constant vertical load and quasi-static reversed cyclic lateral loads, in displacement control. The tests were performed until failure. The tested specimens were designed as 1:3 scale steel-concrete composite elements, representing a three storeys and one bay element from the base of a lateral resisting system made by shear walls. Configuration/arrangement of steel profiles in cross section were varied within the specimens. The main objective of this research consisted in identifying innovative solutions for composite steel-concrete shear walls with enhanced performance, as steel fibre reinforced concrete which was used in order to replace traditional reinforced concrete. A first conclusion was that replacing traditional reinforcement with steel fibre changes the failure mode of the elements, as from a flexural mode, in case of element RCW, to a shear failure mode for CSFRCW. The maximum lateral force had almost similar values but test results indicated an improvement in cracking response, and a decrease in ductility. The addition of steel fibres in the concrete mixture can lead to an increase of the initial cracking force, and can change the sudden opening of a crack in a more stable process.

The interplay between regulatory focus and temporal distance in the health context

NARCIS (Netherlands)

Berezowska, Aleksandra; Fischer, Arnout R.H.; Trijp, van Hans C.M.

2018-01-01

Objectives: This study identifies how the interaction between temporal distance, regulatory focus, and framing of health outcomes affects individuals' intention to adopt a personalized nutrition service. Design: A 2 (temporal distance: immediate health outcomes vs. delayed health outcomes) × 2

Systems Level Engineering of Plant Cell Wall Biosynthesis to Improve Biofuel Feedstock Quality

Energy Technology Data Exchange (ETDEWEB)

Hazen, Samuel

2013-09-27

Our new regulatory model of cell wall biosynthesis proposes original network architecture with several newly incorporated components. The mapped set of protein-DNA interactions will serve as a foundation for 1) understanding the regulation of a complex and integral plant component and 2) the manipulation of crop species for biofuel and biotechnology purposes. This study revealed interesting and novel aspects of grass growth and development and further enforce the importance of a grass model system. By functionally characterizing a suite of genes, we have begun to improve the sparse model for transcription regulation of biomass accumulation in grasses. In the process, we have advanced methodology and brachy molecular genetic tools that will serve as valuable community resource.

Profiling cellular and inflammatory changes in the airway wall of mild to moderate COPD.

Science.gov (United States)

Eapen, Mathew S; McAlinden, Kielan; Tan, Daniel; Weston, Steven; Ward, Chris; Muller, Hans K; Walters, Eugene H; Sohal, Sukhwinder S

2017-08-01

The objective of this study was to enumerate total cells and the number of inflammatory cell differentials in large airways (LAs) versus small airways (SAs) of mild-moderate COPD, and against appropriate controls. For LA, we used endobronchial biopsies and for SA resected lung tissues. Immunostaining was enumerated (cells per mm 2 ) for macrophages, neutrophils, CD4 and CD8 T cells in the lamina propria (LP) up to 150 µM deep for LA and full wall thickness for SA. We confirmed hypocellularity in the LA and in the SA wall in smokers and COPD (P cellularity was least in current smokers with COPD (COPD-CS) (P cellularity was similar across smoker/COPD groups. LA neutrophils were decreased in COPD-CS (P wall inflammation in COPD is oversimplified, and contrast with innate inflammatory activation in the lumen, at least in mild-moderate disease. Any abnormalities in airway wall cell differentials are small, although exaggerated in percentage terms. © 2017 Asian Pacific Society of Respirology.

Measurement of the near-wall velocity profile for a nanofluid flow inside a microchannel

Science.gov (United States)

Kanjirakat, Anoop; Sadr, Reza

2015-11-01

Hydrodynamics and anomalous heat transfer enhancements have been reported in the past for colloidal suspensions of nano-sized particles dispersed in a fluid (nanofluids). However, such augmentations may manifest itself by study of fluid flow characteristics near in the wall region. Present experimental study reports near-wall velocity profile for nanofluids (silicon dioxide nanoparticles in water) measured inside a microchannel. An objective-based nano-Particle Image Velocimetry (nPIV) technique is used to measure fluid velocity within three visible depths, O(100nm), from the wall. The near-wall fluid velocity profile is estimated after implementing the required corrections for optical properties and effects caused by hindered Brownian motion, wall-particle interactions, and non-uniform exponential illumination on the measurement technique. The fluid velocities of nanofluids at each of the three visible depths are observed to be higher than that of the base fluid resulting in a higher shear rate in this region. The relative increase in shear rates for nanofluids is believed to be the result of the near-wall shear-induced particle migration along with the Brownian motion of the nanoparticles. This research is funded by NPRP grant # 08-574-2-239 from the Qatar National Research Fund (a member of Qatar Foundation).

The regulatory process for the decommissioning of nuclear facilities

International Nuclear Information System (INIS)

1990-01-01

The objective of this publication is to provide general guidance to Member States for regulating the decommissioning of nuclear facilities within the established nuclear regulatory framework. The Guide should also be useful to those responsible for, or interested in, the decommissioning of nuclear facilities. The Guide describes in general terms the process to be used in regulating decommissioning and the considerations to be applied in the development of decommissioning regulations and guides. It also delineates the responsibilities of the regulatory body and the licensee in decommissioning. The provisions of this Guide are intended to apply to all facilities within the nuclear fuel cycle and larger industrial installations using long lived radionuclides. For smaller installations, however, less extensive planning and less complex regulatory control systems should be acceptable. The Guide deals primarily with decommissioning after planned shutdown. Most provisions, however, are also applicable to decommissioning after an abnormal event, once cleanup operations have been terminated. The decommissioning planning in this case must take account of the abnormal event. 28 refs, 1 fig

Selection of a discount rate for use in NRC regulatory analyses and application of discount rates to future averted health effects

International Nuclear Information System (INIS)

Paananen, O.H.; Hendrickson, P.L.

1993-01-01

The principal objective of this report is to provide background information and recommendations on the use of discount rates in the regulatory analysis process. The report focuses on two issues selecting the appropriate discount rate or rates to use when conducting a regulatory analysis, and applying the selected discount rate to future health-related benefits estimated to result from alternative regulatory actions

Application of principles of quality assurance recommended by ISO 9000 Standards to Regulatory Program

International Nuclear Information System (INIS)

Jova Sed, Luis Andres; Bilbao Alfonso, Alejandro Victor

2001-01-01

For several years, the necessity of applying the programs of quality assurance to the radiation protection activities has been highlighted; however there has been little progress in this direction, even in the philosophical and methodological development of the topic. The objective of this work is to transmit some recommendations of how the Regulatory Authorities of developing countries can organize the quality assurance system of their own activity, following the main precepts of the international standard series ISO 9000. In very tight synthesis it describes the importance that has the definition of a policy of quality for a Regulatory Authority, the quality objectives, the definition of the responsibilities and attributions in relation with quality assurance, and others elements of the ISO 9000, and how to apply it. (author)

Log-layer mismatch and modeling of the fluctuating wall stress in wall-modeled large-eddy simulations

Science.gov (United States)

Yang, Xiang I. A.; Park, George Ilhwan; Moin, Parviz

2017-10-01

Log-layer mismatch refers to a chronic problem found in wall-modeled large-eddy simulation (WMLES) or detached-eddy simulation, where the modeled wall-shear stress deviates from the true one by approximately 15 % . Many efforts have been made to resolve this mismatch. The often-used fixes, which are generally ad hoc, include modifying subgrid-scale stress models, adding a stochastic forcing, and moving the LES-wall-model matching location away from the wall. An analysis motivated by the integral wall-model formalism suggests that log-layer mismatch is resolved by the built-in physics-based temporal filtering. In this work we investigate in detail the effects of local filtering on log-layer mismatch. We show that both local temporal filtering and local wall-parallel filtering resolve log-layer mismatch without moving the LES-wall-model matching location away from the wall. Additionally, we look into the momentum balance in the near-wall region to provide an alternative explanation of how LLM occurs, which does not necessarily rely on the numerical-error argument. While filtering resolves log-layer mismatch, the quality of the wall-shear stress fluctuations predicted by WMLES does not improve with our remedy. The wall-shear stress fluctuations are highly underpredicted due to the implied use of LES filtering. However, good agreement can be found when the WMLES data are compared to the direct numerical simulation data filtered at the corresponding WMLES resolutions.

75 FR 63878 - Self-Regulatory Organizations; Self-Regulatory Organizations; Notice of Filing and Immediate...

Science.gov (United States)

2010-10-18

...-Regulatory Organizations; Self-Regulatory Organizations; Notice of Filing and Immediate Effectiveness of...(b)(1). \\2\\ 17 CFR 240.19b-4. I. Self-Regulatory Organization's Statement of the Terms of Substance... Public Reference Room. II. Self-Regulatory Organization's Statement of the Purpose of, and Statutory...

Regulatory Office for Network Industries

International Nuclear Information System (INIS)

2005-01-01

The main goal of the economic regulation of network industries is to ensure a balance between the interests of consumers and investors and to encourage providing high-quality goods and services. The task of the regulatory authority is to protect the interests of consumers against monopolistic behaviour of regulated enterprises. At the same time, the regulatory office has to protect the interests of investors by giving them an opportunity to achieve an adequate return on their investments. And last, but not least, the regulatory office has to provide regulated enterprises with appropriate incentives to make them function in an efficient and effective manner and to guarantee the security of delivery of energies and related services. All this creates an efficient regulatory framework that is capable of attracting the required amount and type of investments. This also means providing third party access to the grids, the opening of energy markets, the un-bundling of accounts according to production, distribution, transmission and other activities and the establishment of a transparent and stable legislative environment for regulated companies, investors and consumers. Otherwise, in the long run consumers may suffer from a serious deterioration of service quality, although in the short run they are protected against increased prices. Under the Act No. 276/2001 Coll. on Regulation of Network Industries and on amendment of some acts the Office for Regulation of Network Industries has been commissioned to implement the main objectives of regulation of network industries. By network industries the Act No. 276/2001 Coll. on Regulation means the following areas: (a) Production, purchase, transit and distribution of electricity; (b) Production, purchase, transit and distribution of gas; (c) Production, purchase and distribution of heat; (d) Water management activities relating to the operation of the public water supply system or the public sewerage system; (e) Water management

Communication planning by the nuclear regulatory body

International Nuclear Information System (INIS)

2002-01-01

The national regulatory body, whose primary mission is to exercise regulatory control over nuclear facilities and the use of radiation sources, but not to promote their use, may be the most credible source of neutral, balanced and accurate information about issues relating to nuclear and radiation safety. It is therefore important for a regulatory body to establish and exercise an effective communication programme to acquaint the public with its oversight functions, capabilities and effectiveness. If the regulatory body is to maintain credibility and to deal promptly and effectively with nuclear or radiological accidents and any other events that may give rise to significant public concerns, and is to communicate clearly and effectively with the public, it must have adequate resources, including experts in nuclear safety. And if maintaining public confidence in the authorities and avoiding unnecessary concerns are among its principal objectives, it must be able to communicate understandably and truthfully about the known extent of any accident, the actions taken in response to it and its implications. In the past, psychological effects as a result of certain severe nuclear and radiological accidents have been compounded by a lack of candour with the public on the part of the authorities and an absence of an appropriate programme of public information. This publication describes good practices and gives practical examples of how the regulatory body can establish a systematic and structured programme for enhancing effective communication with various parties and under various circumstances. The report presupposes an adequate national infrastructure, including an independent regulatory body with sufficient authority and resources to discharge its responsibilities for the regulation of safety. This Safety Report covers the elements of a regulatory body's programme for communication with various audiences and under the different circumstances that may be encountered

Regulatory challenges in using nuclear operating experience

International Nuclear Information System (INIS)

2006-01-01

The fundamental objective of all nuclear safety regulatory bodies is to ensure that nuclear utilities operate their plants in an acceptably safe manner at all times. Learning from experience has been a key element in meeting this objective. It is therefore very important for nuclear power plant operators to have an active programme for collecting, analysing and acting on the lessons of operating experience that could affect the safety of their plants. NEA experts have noted that almost all of the recent, significant events reported at international meetings have occurred earlier in one form or another. Counteractions are usually well-known, but information does not always seem to reach end users, or corrective action programmes are not always rigorously applied. Thus, one of the challenges that needs to be met in order to maintain good operational safety performance is to ensure that operating experience is promptly reported to established reporting systems, preferably international in order to benefit from a larger base of experience, and that the lessons from operating experience are actually used to promote safety. This report focuses on how regulatory bodies can ensure that operating experience is used effectively to promote the safety of nuclear power plants. While directed at nuclear power plants, the principles in this report may apply to other nuclear facilities as well. (author)

Evolution of Cis-Regulatory Elements and Regulatory Networks in Duplicated Genes of Arabidopsis.

Science.gov (United States)

Arsovski, Andrej A; Pradinuk, Julian; Guo, Xu Qiu; Wang, Sishuo; Adams, Keith L

2015-12-01

Plant genomes contain large numbers of duplicated genes that contribute to the evolution of new functions. Following duplication, genes can exhibit divergence in their coding sequence and their expression patterns. Changes in the cis-regulatory element landscape can result in changes in gene expression patterns. High-throughput methods developed recently can identify potential cis-regulatory elements on a genome-wide scale. Here, we use a recent comprehensive data set of DNase I sequencing-identified cis-regulatory binding sites (footprints) at single-base-pair resolution to compare binding sites and network connectivity in duplicated gene pairs in Arabidopsis (Arabidopsis thaliana). We found that duplicated gene pairs vary greatly in their cis-regulatory element architecture, resulting in changes in regulatory network connectivity. Whole-genome duplicates (WGDs) have approximately twice as many footprints in their promoters left by potential regulatory proteins than do tandem duplicates (TDs). The WGDs have a greater average number of footprint differences between paralogs than TDs. The footprints, in turn, result in more regulatory network connections between WGDs and other genes, forming denser, more complex regulatory networks than shown by TDs. When comparing regulatory connections between duplicates, WGDs had more pairs in which the two genes are either partially or fully diverged in their network connections, but fewer genes with no network connections than the TDs. There is evidence of younger TDs and WGDs having fewer unique connections compared with older duplicates. This study provides insights into cis-regulatory element evolution and network divergence in duplicated genes. © 2015 American Society of Plant Biologists. All Rights Reserved.

Quantitative CT: Associations between Emphysema, Airway Wall Thickness and Body Composition in COPD

DEFF Research Database (Denmark)

Rutten, Erica P A; Grydeland, Thomas B; Pillai, Sreekumar G

2011-01-01

, CT scans were performed to determine emphysema (%LAA), airway wall thickness (AWT-Pi10), and lung mass. Muscle wasting based on FFMI was assessed by bioelectrical impedance. In both the men and women with COPD, FFMI was negatively associated with %LAA. FMI was positively associated with AWT-Pi10......The objective of the present study was to determine the association between CT phenotypes-emphysema by low attenuation area and bronchitis by airway wall thickness-and body composition parameters in a large cohort of subjects with and without COPD. In 452 COPD subjects and 459 subjects without COPD...... in both subjects with and without COPD. Among the subjects with muscle wasting, the percentage emphysema was high, but the predictive value was moderate. In conclusion, the present study strengthens the hypothesis that the subgroup of COPD cases with muscle wasting have emphysema. Airway wall thickness...

Quantitative CT: Associations between Emphysema, Airway Wall Thickness and Body Composition in COPD

DEFF Research Database (Denmark)

Rutten, Erica P A; Grydeland, Thomas B; Pillai, Sreekumar G

2011-01-01

The objective of the present study was to determine the association between CT phenotypes-emphysema by low attenuation area and bronchitis by airway wall thickness-and body composition parameters in a large cohort of subjects with and without COPD. In 452 COPD subjects and 459 subjects without COPD......, CT scans were performed to determine emphysema (%LAA), airway wall thickness (AWT-Pi10), and lung mass. Muscle wasting based on FFMI was assessed by bioelectrical impedance. In both the men and women with COPD, FFMI was negatively associated with %LAA. FMI was positively associated with AWT-Pi10...... in both subjects with and without COPD. Among the subjects with muscle wasting, the percentage emphysema was high, but the predictive value was moderate. In conclusion, the present study strengthens the hypothesis that the subgroup of COPD cases with muscle wasting have emphysema. Airway wall thickness...

Towards a single European electricity market. A structured approach to regulatory mode decision-making

International Nuclear Information System (INIS)

De Jong, H.M.

2009-01-01

This study focuses on the processes through which the rules and regulations that govern European electricity markets - and inherently, their integration process - are established. So far, European policy makers have largely followed a 'trial-and-error' approach to finding an appropriate regulatory mode (process) for dealing effectively with market integration issues. This unstructured approach to regulatory mode selection leads to several problems: - Today's trial-and-error strategy of shifting from one regulatory mode to another is time-consuming. - In the regulatory mode selection process, certain key principles of good governance are insufficiently considered. - European regulatory processes are experienced as vague, intransparent, and illegitimate by 'outside' stakeholders. This study develops a 'structured approach to regulatory mode decision-making' (STARMODE) based on the theory of decision modelling in policy management and a case study exploring three key market integration issues in the field of electricity markets: interconnector investment, congestion management and market transparency. The main objective is to present a systematic and comprehensive framework for analysing and improving regulatory mode decision-making in the context of the European Union, focusing on electricity market integration. The STARMODE approach is generally applicable to (and relevant for) European market integration issues in industries characterized by a natural monopoly and/or an essential service. The approach may also contribute to national regulatory mode decision-making and multi-state decision-making in other continents.

Crisis Communication of Nuclear Regulatory Organisations: Towards global thinking

International Nuclear Information System (INIS)

Martell, Meritxell; Menendez, Susan; Calvo, Marina

2013-01-01

The OECD Nuclear Energy Agency (NEA) Committee on Nuclear Regulatory Activities (CNRA) Working Group on Public Communication of Nuclear Regulatory Organisations (WGPC) organised the workshop 'Crisis communication: facing the challenges' on 9-10 May 2012 in Madrid to address the international dimension of the communicative responses to crises by assessing the experience of Nuclear Regulatory Organisations of the NEA member countries and their stakeholders. The CNRA/WGPC also prepared in 2011, before the Fukushima-Daiichi nuclear accident occurred, a Road Map for Crisis Communication of Nuclear Regulatory Organisations which focused only on national aspects. This 'road map' had not considered the international dimension. CNRA mandated the WGPC to expand the Road Map so as to conclude the follow-up activity on crisis communication. The objective of the present document is to firstly, identify the key messages which can be extracted from three surveys carried out among the WGPC members after Fukushima-Daiichi's accident (Appendices II, III and IV), and incorporate them into the Road Map for Crisis Communication. Secondly, the good practices on public communication of NROs, which were presented during the OECD/NEA Workshop on Crisis Communication: Facing the Challenges, are reported. Following the structure of the road map for public communication responses during crisis included in the NEA report entitled 'Road Map for Crisis Communication of Nuclear Regulatory Organisations - National aspects', the good practices on communication before, during and after a crisis are provided. Overall, the emphasis of this report is on the international aspects of crisis communication, rather than the national dimension. (authors)

Effects of Wall-Normal and Angular Momentum Injections in Airfoil Separation Control

Science.gov (United States)

Munday, Phillip M.; Taira, Kunihiko

2018-05-01

The objective of this computational study is to quantify the influence of wall-normal and angular momentum injections in suppressing laminar flow separation over a canonical airfoil. Open-loop control of fully separated, incompressible flow over a NACA 0012 airfoil at $\\alpha = 9^\\circ$ and $Re = 23,000$ is examined with large-eddy simulations. This study independently introduces wall-normal momentum and angular momentum into the separated flow using swirling jets through model boundary conditions. The response of the flow field and the surface vorticity fluxes to various combinations of actuation inputs are examined in detail. It is observed that the addition of angular momentum input to wall-normal momentum injection enhances the suppression of flow separation. Lift enhancement and suppression of separation with the wall-normal and angular momentum inputs are characterized by modifying the standard definition of the coefficient of momentum. The effect of angular momentum is incorporated into the modified coefficient of momentum by introducing a characteristic swirling jet velocity based on the non-dimensional swirl number. With this single modified coefficient of momentum, we are able to categorize each controlled flow into separated, transitional, and attached flows.

Regulatory activities; Actividades regulatorias

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-07-01

This publication, compiled in 8 chapters, presents the regulatory system developed by the Nuclear Regulatory Authority (NRA) of the Argentine Republic. The following activities and developed topics in this document describe: the evolution of the nuclear regulatory activity in Argentina; the Argentine regulatory system; the nuclear regulatory laws and standards; the inspection and safeguards of nuclear facilities; the emergency systems; the environmental systems; the environmental monitoring; the analysis laboratories on physical and biological dosimetry, prenatal irradiation, internal irradiation, radiation measurements, detection techniques on nuclear testing, medical program on radiation protection; the institutional relations with national and international organization; the training courses and meeting; the technical information.

Nuclear safety and security culture - an integrated approach to regulatory oversight

International Nuclear Information System (INIS)

Tronea, M.; Ciurea Ercau, C.

2013-01-01

The paper presents the development and implementation of regulatory guidelines for the oversight of safety and security culture within licensees organizations. CNCAN (the National Commission for Nuclear Activities of Romania) has used the International Atomic Energy Agency (IAEA) attributes for a strong safety culture as the basis for its regulatory guidelines providing support to the reviewers and inspectors for recognizing and gathering information relevant to safety culture. These guidelines are in process of being extended to address also security culture, based on the IAEA Nuclear Security Series No. 7 document Nuclear Security Culture: Implementing Guide. Recognizing that safety and security cultures coexist and need to reinforce each other because they share the common objective of limiting risk and that similar regulatory review and inspection processes are in place for nuclear security oversight, an integrated approach is considered justified, moreover since the common elements of these cultures outweigh the differences. (authors)

Prediction of wall shear stresses in transitional boundary layers using near-wall mean velocity profiles

International Nuclear Information System (INIS)

Jeon, Woo Pyung; Shin, Sung Ho; Kang, Shin Hyoung

2000-01-01

The local wall shear stress in transitional boundary layer was estimated from the near-wall mean velocity data using the principle of Computational Preston tube Method(CPM). The previous DNS and experimental databases of transitional boundary layers were used to demonstrate the accuracy of the method and to provide the applicable range of wall unit y + . The skin friction coefficients predicted by the CPM agreed well with those from previous studies. To reexamine the applicability of the CPM, near-wall hot-wire measurements were conducted in developing transitional boundary layers on a flat plate with different freestream turbulence intensities. The intermittency profiles across the transitional boundary layers were reasonably obtained from the conditional sampling technique. An empirical correlation between the representative intermittency near the wall and the free parameter K 1 of the extended wall function of CPM has been newly proposed using the present and other experimental data. The CPM has been verified as a useful tool to measure the wall shear stress in transitional boundary layer with reasonable accuracy

A waste package strategy for regulatory compliance

International Nuclear Information System (INIS)

Stahl, D.; Cloninger, M.O.

1990-01-01

This paper summarizes the strategy given in the Site Characterization Plan for demonstrating compliance with the post closure performance objectives for the waste package and the Engineered Barrier System contained in the Code of Federal Regulations. The strategy consists of the development of a conservative waste package design that will meet the regulatory requirements with sufficient margin for uncertainty using a multi-barrier approach that takes advantage of the unsaturated nature of the Yucca Mountain site. 7 refs., 1 fig

Assessment of wall-thinning in carbon steel pipe by using laser-generated guided wave

Energy Technology Data Exchange (ETDEWEB)

Kim, Do Yong; Cho, Youn Ho; Lee, Joon Hyun [Pusan National University, School of Mechanical Engineering, Busan (Korea, Republic of)

2010-10-15

The objective of this research is to estimate the crack location and size of a carbon steel pipe by using a laser ultrasound guided wave for the wall thinning evaluation of an elbow. The wall thinning of the carbon steel pipe is one of the most serious problems in nuclear power plants, especially the wall thinning of the carbon steel elbow caused by Flow-Accelerated Corrosion (FAC). Therefore, a non-destructive inspection method of elbow is essential for the nuclear power plants to operate safely. The specimens used in this study were carbon steel elbows, which represented the main elements of real nuclear power plants. The shape of the wall thinning was an oval with a width of 120mm, a length of 80mm, and a depth of 5mm. The L(0,1) and L(0,2) modes variation of the ultrasound guided wave signal is obtained from the response of the laser generation/air-coupled detection ultrasonic hybrid system represent the characteristics of the defect. The trends of these characteristics and signal processing were use dto estimate the size and location of wall thinning

Assessment of wall-thinning in carbon steel pipe by using laser-generated guided wave

International Nuclear Information System (INIS)

Kim, Do Yong; Cho, Youn Ho; Lee, Joon Hyun

2010-01-01

The objective of this research is to estimate the crack location and size of a carbon steel pipe by using a laser ultrasound guided wave for the wall thinning evaluation of an elbow. The wall thinning of the carbon steel pipe is one of the most serious problems in nuclear power plants, especially the wall thinning of the carbon steel elbow caused by Flow-Accelerated Corrosion (FAC). Therefore, a non-destructive inspection method of elbow is essential for the nuclear power plants to operate safely. The specimens used in this study were carbon steel elbows, which represented the main elements of real nuclear power plants. The shape of the wall thinning was an oval with a width of 120mm, a length of 80mm, and a depth of 5mm. The L(0,1) and L(0,2) modes variation of the ultrasound guided wave signal is obtained from the response of the laser generation/air-coupled detection ultrasonic hybrid system represent the characteristics of the defect. The trends of these characteristics and signal processing were use dto estimate the size and location of wall thinning

Conserved Transcriptional Regulatory Programs Underlying Rice and Barley Germination

Science.gov (United States)

Lin, Li; Tian, Shulan; Kaeppler, Shawn; Liu, Zongrang; An, Yong-Qiang (Charles)

2014-01-01

Germination is a biological process important to plant development and agricultural production. Barley and rice diverged 50 million years ago, but share a similar germination process. To gain insight into the conservation of their underlying gene regulatory programs, we compared transcriptomes of barley and rice at start, middle and end points of germination, and revealed that germination regulated barley and rice genes (BRs) diverged significantly in expression patterns and/or protein sequences. However, BRs with higher protein sequence similarity tended to have more conserved expression patterns. We identified and characterized 316 sets of conserved barley and rice genes (cBRs) with high similarity in both protein sequences and expression patterns, and provided a comprehensive depiction of the transcriptional regulatory program conserved in barley and rice germination at gene, pathway and systems levels. The cBRs encoded proteins involved in a variety of biological pathways and had a wide range of expression patterns. The cBRs encoding key regulatory components in signaling pathways often had diverse expression patterns. Early germination up-regulation of cell wall metabolic pathway and peroxidases, and late germination up-regulation of chromatin structure and remodeling pathways were conserved in both barley and rice. Protein sequence and expression pattern of a gene change quickly if it is not subjected to a functional constraint. Preserving germination-regulated expression patterns and protein sequences of those cBRs for 50 million years strongly suggests that the cBRs are functionally significant and equivalent in germination, and contribute to the ancient characteristics of germination preserved in barley and rice. The functional significance and equivalence of the cBR genes predicted here can serve as a foundation to further characterize their biological functions and facilitate bridging rice and barley germination research with greater confidence. PMID

The Bacillus subtilis GntR Family Repressor YtrA Responds to Cell Wall Antibiotics▿§

Science.gov (United States)

Salzberg, Letal I.; Luo, Yun; Hachmann, Anna-Barbara; Mascher, Thorsten; Helmann, John D.

2011-01-01

The transglycosylation step of cell wall synthesis is a prime antibiotic target because it is essential and specific to bacteria. Two antibiotics, ramoplanin and moenomycin, target this step by binding to the substrate lipid II and the transglycosylase enzyme, respectively. Here, we compare the ramoplanin and moenomycin stimulons in the Gram-positive model organism Bacillus subtilis. Ramoplanin strongly induces the LiaRS two-component regulatory system, while moenomycin almost exclusively induces genes that are part of the regulon of the extracytoplasmic function (ECF) σ factor σM. Ramoplanin additionally induces the ytrABCDEF and ywoBCD operons, which are not part of a previously characterized antibiotic-responsive regulon. Cluster analysis reveals that these two operons are selectively induced by a subset of cell wall antibiotics that inhibit lipid II function or recycling. Repression of both operons requires YtrA, which recognizes an inverted repeat in front of its own operon and in front of ywoB. These results suggest that YtrA is an additional regulator of cell envelope stress responses. PMID:21856850

Regulatory Technology Development Plan - Sodium Fast Reactor. Mechanistic Source Term - Trial Calculation. Work Plan

International Nuclear Information System (INIS)

Grabaskas, David; Bucknor, Matthew; Jerden, James; Brunett, Acacia J.

2016-01-01

The overall objective of the SFR Regulatory Technology Development Plan (RTDP) effort is to identify and address potential impediments to the SFR regulatory licensing process. In FY14, an analysis by Argonne identified the development of an SFR-specific MST methodology as an existing licensing gap with high regulatory importance and a potentially long lead-time to closure. This work was followed by an initial examination of the current state-of-knowledge regarding SFR source term development (ANLART-3), which reported several potential gaps. Among these were the potential inadequacies of current computational tools to properly model and assess the transport and retention of radionuclides during a metal fuel pool-type SFR core damage incident. The objective of the current work is to determine the adequacy of existing computational tools, and the associated knowledge database, for the calculation of an SFR MST. To accomplish this task, a trial MST calculation will be performed using available computational tools to establish their limitations with regard to relevant radionuclide release/retention/transport phenomena. The application of existing modeling tools will provide a definitive test to assess their suitability for an SFR MST calculation, while also identifying potential gaps in the current knowledge base and providing insight into open issues regarding regulatory criteria/requirements. The findings of this analysis will assist in determining future research and development needs.

Hot wire production of single-wall and multi-wall carbon nanotubes

Science.gov (United States)

Dillon, Anne C.; Mahan, Archie H.; Alleman, Jeffrey L.

2010-10-26

Apparatus (210) for producing a multi-wall carbon nanotube (213) may comprise a process chamber (216), a furnace (217) operatively associated with the process chamber (216), and at least one filament (218) positioned within the process chamber (216). At least one power supply (220) operatively associated with the at least one filament (218) heats the at least one filament (218) to a process temperature. A gaseous carbon precursor material (214) operatively associated with the process chamber (216) provides carbon for forming the multi-wall carbon nanotube (213). A metal catalyst material (224) operatively associated with the process (216) catalyzes the formation of the multi-wall carbon nanotube (213).

A method to quantitate regional wall motion in left ventriculography using Hildreth algorithm

Energy Technology Data Exchange (ETDEWEB)

Terashima, Mikio [Hyogo Red Cross Blood Center (Japan); Naito, Hiroaki; Sato, Yoshinobu; Tamura, Shinichi; Kurosawa, Tsutomu

1998-06-01

Quantitative measurement of ventricular wall motion is indispensable for objective evaluation of cardiac function associated with coronary artery disease. We have modified the Hildreth`s algorithm to estimate excursions of the ventricular wall on left ventricular images yielded by various imaging techniques. Tagging cine-MRI was carried out on 7 healthy volunteers. The original Hildreth method, the modified Hildreth method and the centerline method were applied to the outlines of the images obtained, to estimate excursion of the left ventricular wall and regional shortening and to evaluate the accuracy of these methods when measuring these parameters, compared to the values of these parameters measured actually using the attached tags. The accuracy of the original Hildreth method was comparable to that of the centerline method, while the modified Hildreth method was significantly more accurate than the centerline method (P<0.05). Regional shortening as estimated using the modified Hildreth method differed less from the actually measured regional shortening than did the shortening estimated using the centerline method (P<0.05). The modified Hildreth method allowed reasonable estimation of left ventricular wall excursion in all cases where it was applied. These results indicate that when applied to left ventriculograms for ventricular wall motion analysis, the modified Hildreth method is more useful than the original Hildreth method. (author)

Implementing Green Walls in Schools.

Science.gov (United States)

McCullough, Michael B; Martin, Michael D; Sajady, Mollika A

2018-01-01

Numerous studies in applied pedagogical design have shown that, at all educational levels, direct exposure to the natural environment can enhance learning by improving student attention and behaviors. Implementing green walls-a "vertical garden," or "living wall" interior wall that typically includes greenery, a growing medium (soil or substrate) and a water delivery system-provides environmental health benefits, but also provides a practical application within classrooms for minimizing directed attention fatigue in students by connecting them to "outdoor nature" within the indoor environment. Hands-on "project-based" learning is another pedagogical strategy that has proved to be effective across the spectrum of educational levels and across subject areas. Green walls have the potential to inspire critical thinking through a combination of project-based learning strategies and environmental education. The authors have outlined a curriculum involving the implementation of an indoor living wall system within a classroom-learning environment, incorporating project-based learning modules that interact with the wall. In conjunction with the passive health benefits of a green wall, project-based curriculum models can connect students interactively with indoor nature and have the potential to inspire real-world thinking related to science, technology, engineering, art, and mathematics fields within the indoor learning environment. Through a combination of these passive and interactive modes, students are connected to nature in the indoor environment regardless of weather conditions outdoors. Future research direction could include post-construction studies of the effectiveness of project-based curricula related to living walls, and the long-term impacts of implementing green walls in classrooms on school achievement and student behaviors.

Assessment of dry-stone terrace wall degradation with a 3D approach

Science.gov (United States)

Djuma, Hakan; Camera, Corrado; Faka, Marina; Bruggeman, Adriana; Hermon, Sorin

2016-04-01

In the Mediterranean basin, terracing is a common element of agricultural lands. Terraces retained by dry-stone walls are used to conserve arable soil, delay erosion processes and retain rainfall runoff. Currently, agricultural land abandonment is widespread in the Mediterranean region leading to terrace wall failure due to lack of maintenance and consequently an increase in soil erosion. The objective of this study is to test the applicability of digital 3D documentation on mountainous agricultural areas for assessing changes in terrace wall geometry, including terrace wall failures and associated soil erosion. The study area is located at 800-1100 m above sea level, in the Ophiolite complex of the Troodos Mountains in Cyprus. Average annual precipitation is 750 mm. Two sites with dry-stone terraces were selected for this study. The first site had a sequence of three terrace walls that were surveyed. The uppermost terrace wall was collapsed at several locations; the middle at few locations; and the lowest was still intact. Three fieldwork campaigns were conducted at this site: during the dry season (initial conditions), the middle and end of the wet season. The second site had one terrace wall that was almost completely collapsed. This terrace was restored during a communal terrace rehabilitation event. Two fieldwork campaigns were conducted for this terrace: before and after the terrace wall restoration. Terrace walls were documented with a set of digital images, and transformed into a 3D point cloud (using web-based services and commercial software - Autodesk 123D catch and Menci Software uMap, respectively). A set of points, registered with the total station and geo-referenced with a GPS, enabled the scaling of the 3D model and aligning the terrace walls within the same reference system. The density (distance between each point) of the reconstructed point clouds is 0.005 m by Umap and 0.025 m by 123D Catch. On the first site, the model analysis identified wall

Anisotropy of domain wall resistance

Science.gov (United States)

Viret; Samson; Warin; Marty; Ott; Sondergard; Klein; Fermon

2000-10-30

The resistive effect of domain walls in FePd films with perpendicular anisotropy was studied experimentally as a function of field and temperature. The films were grown directly on MgO substrates, which induces an unusual virgin magnetic configuration composed of 60 nm wide parallel stripe domains. This allowed us to carry out the first measurements of the anisotropy of domain wall resistivity in the two configurations of current perpendicular and parallel to the walls. At 18 K, we find 8.2% and 1.3% for the domain wall magnetoresistance normalized to the wall width (8 nm) in these two respective configurations. These values are consistent with the predictions of Levy and Zhang.

The core to regulatory reform

International Nuclear Information System (INIS)

Partridge, J.W. Jr.

1993-01-01

Federal Energy Regulatory Commission (FERC) Orders 436, 500, and 636, the Clean Air Act Amendments of 1990, Public Utility Holding Company Act reform, and the 1992 Energy Policy Act all can have significant effects on an LDC's operations. Such changes in an LDC's environments must be balanced by changes within the utility, its marketplace, and its state regulatory environment. The question is where to start. For Columbia Gas Distribution Cos., based in Columbus, OH, the new operating foundation begins with each employee. Internal strength is critical in designing initiatives that meet the needs of the marketplace and are well-received by regulators. Employees must understand not only the regulatory environment in which the LDC operates, but also how their work contributes to a positive regulatory relationship. To achieve this, Columbia initiated the COntinuing Regulatory Education program, or CORE, in 1991. CORE is a regulatory-focused, information-initiative program coordinated by Columbia's Regulatory Policy, Planning, and Government Affairs Department. The CORE programs can take many forms, such as emerging issue discussions, dialogues with regulators and key parties, updates on regulatory fillings, regulatory policy meetings, and formal training classes. The speakers and discussion facilitators can range from human resource department trainers to senior officers, from regulatory department staff members to external experts, or from state commissioners to executives from other LDCs. The goals of CORE initiatives are to: Support a professional level of regulatory expertise through employee participation in well-developed regulatory programs presented by credible experts. Encourage a constructive state regulatory environment founded on communication and cooperation. CORE achieves these goals via five program levels: introductory basics, advanced learning, professional expertise, crossfunctional dialogues, and external idea exchanges

Canada's regulatory framework: The Canadian Nuclear Safety Commission's regulatory framework

International Nuclear Information System (INIS)

Howard, D.

2011-01-01

non-proliferation of nuclear weapons and nuclear explosive devices; dissemination of scientific, technical and regulatory information concerning the activities of CNSC, and the effects on the environment, on the health and safety of persons, of the development, production, possession, transport and use of nuclear substances. The prime responsibility for safety including the management of low- and intermediate-level radioactive waste rests with the licensee in possession of the nuclear material. While neither the NSCA nor its associated regulations define radioactive waste, Regulatory Policy P-290, Managing Radioactive Waste, asserts that radioactive waste is any liquid, gaseous or solid material that contains a nuclear substance, as defined in section 2 of the NSCA and for which the owner of the material foresees no further use and the owner had declared as waste. By definition, a radioactive waste may contain non-radioactive constituents. Radioactive waste is therefore regulated in the same manner as all other materials that contain a nuclear substance. The generation of radioactive waste cannot be prevented entirely but it should be kept to the minimum practicable as an essential objective of radioactive waste management. This objective is in line with CNSC Regulatory Policy P-290. Waste minimization relates to both volume and activity and to both the waste generated by an initial undertaking and the secondary waste resulting from the management of radioactive waste. The chemical characteristics of the waste should also be controlled at source in order to facilitate subsequent processing. As part of the CNSC's effort to improve and modernize its Regulatory Framework, the CNSC is considering several upgrades to the Framework. The CNSC as part of its licensing framework introduced Safety and Control Areas. One of the Safety and Control Areas is waste management. To address the SCA of waste management, the CNSC will be implementing a requirement that each licensee

The regulatory effects of interleukin-12 on interleukin-18 and ...

African Journals Online (AJOL)

Soheir R. Demian

2011-08-24

Aug 24, 2011 ... Objective: To investigate the regulatory effects of IL-12 on IL-18 and IFN-c production in patients with breast cancer. ... IL-18 and IFN-c levels assessed using ELISA before and after ... Multiple factors are associated with increased risk of its ... role in the manifestations of T cell mediated immunity in cancer.

KETERASINGAN DALAM FILM WALL-E

Directory of Open Access Journals (Sweden)

Rahmadya Putra Nugraha

2017-05-01

Full Text Available Modern society nowadays technological advances at first create efficiency in human life. Further development of the technology thus drown human in a routine and automation of work created. The State is to be one of the causes of man separated from fellow or the outside world and eventually experiencing alienation. The movie as a mass media function to obtain the movie and entertainment can be informative or educative function is contained, even persuasive. The purpose of this research was conducted to find out the alienation in the movie Wall E. The concepts used to analyze the movie Wall E this is communication, movie, and alienation. The concept of alienation of human alienation from covering its own products of human alienation from its activities, the human alienation from nature of his humanity and human alienation from each other. Paradigm used is a critical paradigm with type a descriptive research with qualitative approach. The method used is the analysis of semiotics Roland Barthes to interpretation the scope of social alienation and fellow humans in the movie.This writing research results found that alienation of humans with other humans influenced the development of the technology and how the human it self represented of technology, not from our fellow human beings. Masyarakat modern saat ini kemajuan teknologi pada awalnya membuat efisiensi dalam kehidupan manusia. Perkembangan selanjutnya teknologi justru menenggelamkan manusia dalam suatu rutinitas dan otomatisasi kerja yang diciptakan. Keadaan itulah yang menjadi salah satu penyebab manusia terpisah dari sesama atau dunia luar dan akhirnya mengalami keterasingan. Film sebagai media massa berfungsi untuk memperoleh hiburan dan dalam film dapat terkandung fungsi informatif maupun edukatif, bahkan persuasif. Tujuan Penelitian ini dilakukan untuk mengetahui Keterasingan dalam film Wall E. Konsep-konsep yang digunakan untuk menganalisis film Wall E ini adalah komunikasi, film, dan

76 FR 66344 - Self-Regulatory Organizations; Financial Industry Regulatory Authority, Inc.; Order Approving...

Science.gov (United States)

2011-10-26

...-Regulatory Organizations; Financial Industry Regulatory Authority, Inc.; Order Approving Proposed Rule Change... 31, 2011, Financial Industry Regulatory Authority, Inc. (``FINRA'') (f/k/a National Association of... consolidation process, see Information Notice, March 12, 2008 (Rulebook Consolidation Process). For convenience...

75 FR 17456 - Self-Regulatory Organizations; Financial Industry Regulatory Authority, Inc.; Order Approving...

Science.gov (United States)

2010-04-06

...-Regulatory Organizations; Financial Industry Regulatory Authority, Inc.; Order Approving Proposed Rule Change..., Financial Industry Regulatory Authority, Inc. (``FINRA'') filed with the Securities and Exchange Commission... terms. For more information about the rulebook consolidation process, see Information Notice, March 12...

Temporal Regulation of the Bacillus subtilis Acetylome and Evidence for a Role of MreB Acetylation in Cell Wall Growth.

Science.gov (United States)

Carabetta, Valerie J; Greco, Todd M; Tanner, Andrew W; Cristea, Ileana M; Dubnau, David

2016-05-01

N ε -Lysine acetylation has been recognized as a ubiquitous regulatory posttranslational modification that influences a variety of important biological processes in eukaryotic cells. Recently, it has been realized that acetylation is also prevalent in bacteria. Bacteria contain hundreds of acetylated proteins, with functions affecting diverse cellular pathways. Still, little is known about the regulation or biological relevance of nearly all of these modifications. Here we characterize the cellular growth-associated regulation of the Bacillus subtilis acetylome. Using acetylation enrichment and quantitative mass spectrometry, we investigate the logarithmic and stationary growth phases, identifying over 2,300 unique acetylation sites on proteins that function in essential cellular pathways. We determine an acetylation motif, EK(ac)(D/Y/E), which resembles the eukaryotic mitochondrial acetylation signature, and a distinct stationary-phase-enriched motif. By comparing the changes in acetylation with protein abundances, we discover a subset of critical acetylation events that are temporally regulated during cell growth. We functionally characterize the stationary-phase-enriched acetylation on the essential shape-determining protein MreB. Using bioinformatics, mutational analysis, and fluorescence microscopy, we define a potential role for the temporal acetylation of MreB in restricting cell wall growth and cell diameter. The past decade highlighted N ε -lysine acetylation as a prevalent posttranslational modification in bacteria. However, knowledge regarding the physiological importance and temporal regulation of acetylation has remained limited. To uncover potential regulatory roles for acetylation, we analyzed how acetylation patterns and abundances change between growth phases in B. subtilis . To demonstrate that the identification of cell growth-dependent modifications can point to critical regulatory acetylation events, we further characterized MreB, the cell

Guideline for regulatory agencies in evaluating contents of root cause analysis by operators

International Nuclear Information System (INIS)

Hata, Takaya; Makino, Maomi; Kosaka, Atsuhiko

2008-01-01

'Guideline for Regulatory Agencies in Evaluating Contents of Root cause Analysis by Operators' was enacted as the policy for new inspection system in Japan. The objective is to indicate the view point to verify the appropriateness of the corrective actions and preventive actions implemented by operators based on root cause analysis and its analysis results. This guideline is leading to take four points into special consideration for adequate application. They are encouragement of further activities of the operators, flexible interpretation of the intention, versatility of the analysis methods and concepts and consideration of no blame culture. Moreover, as view point for regulatory agencies, it indicates with special emphasis that neutrality of the analyzing party, objectivity of analysis result, and logicality of the analysis method are ensured. This guideline shall be continuously reviewed through integration of lessons learned from active use in future. (author)

78 FR 62784 - Self-Regulatory Organizations; Financial Industry Regulatory Authority, Inc.; Notice of...

Science.gov (United States)

2013-10-22

...-Regulatory Organizations; Financial Industry Regulatory Authority, Inc.; Notice of Designation of a Longer... 5210 (Publication of Transactions and Quotations) October 4, 2013. I. Introduction On August 15, 2013, Financial Industry Regulatory Authority, Inc. (``FINRA'') filed with the Securities and Exchange Commission...

Dressed Domain Walls and holography

International Nuclear Information System (INIS)

Grisa, Luca; Pujolas, Oriol

2008-01-01

The cutoff version of the AdS/CFT correspondence states that the Randall Sundrum scenario is dual to a Conformal Field Theory (CFT) coupled to gravity in four dimensions. The gravitational field produced by relativistic Domain Walls can be exactly solved in both sides of the correspondence, and thus provides one further check of it. We show in the two sides that for the most symmetric case, the wall motion does not lead to particle production of the CFT fields. Still, there are nontrivial effects. Due to the trace anomaly, the CFT effectively renormalizes the Domain Wall tension. On the five dimensional side, the wall is a codimension 2 brane localized on the Randall-Sundrum brane, which pulls the wall in a uniform acceleration. This is perceived from the brane as a Domain Wall with a tension slightly larger than its bare value. In both cases, the deviation from General Relativity appears at nonlinear level in the source, and the leading corrections match to the numerical factors.

Regulatory Politic for the radiological protection to the patient

International Nuclear Information System (INIS)

Betancourt Hernandez, L.A.; De la Fuente Puch, A.; Jerez Vegueria, P.

1998-01-01

The present work has as objective to propose on based to the national experience the Regulatory Authority, the reach the competition to this authorization in the regulation to the topics with the patients protection and to base starting from the content the apendice II to the Basic Standards, the approaches in those that it should impact directly in the acting give their functions to assure it

Role of 3.0 T MR vessel wall imaging for identifying the activity of takayasu arteritis

International Nuclear Information System (INIS)

Liu Xiaosheng; Xu Jianrong; Zhao Huilin; Cheng Fang; Lu Qing; Yao Qiuying

2010-01-01

Objective: To analyze and explore the value of 3 T high resolution magnetic resonance vessel wall imaging for identifying the activity of Takayasu arteritis. Methods: Twenty-six consecutive patients with Takayasu arteritis underwent 3.0 T high resolution MR vessel wall imaging on supraortic vessels (according to the classification of Lupi-Herrea, type I and III were included). Sixteen patients were in active phase and 10 in inactive phase based on the Kerr criteria. The MR vessel wall imaging appearances of Takayasu arteritis were compared between the active phase and inactive phase cases. Results: Wall thickening was demonstrated in all involved arteries. There were statistically significant differences between active phase and inactive phase cases in MR appearances including multi-ring thickening of vessel wall (75/80 and 18/50), arterial inner wail enhancement (50/80 and 19/50), obscurity of perivascular fat (55/80 and 18/50, X 2 =50.39, 7.41, 13.40, P<0.01). There was also a statistically significant difference in the thickness of carotid artery wall between the two groups [ (3.8 ± 0.2) mm vs (2.5 ± 0.8) mm]. Conclusion: 3 T high resolution MR vessel wall imaging is valuable for identifying the activity of Takayasu arteritis. (authors)

Bacillus subtilis as a Platform for Molecular Characterisation of Regulatory Mechanisms of Enterococcus faecalis Resistance against Cell Wall Antibiotics

OpenAIRE

Fang, Chong; Stiegeler, Emanuel; Cook, Gregory M.; Mascher, Thorsten; Gebhard, Susanne

2014-01-01

To combat antibiotic resistance of Enterococcus faecalis, a better understanding of the molecular mechanisms, particularly of antibiotic detection, signal transduction and gene regulation is needed. Because molecular studies in this bacterium can be challenging, we aimed at exploiting the genetically highly tractable Gram-positive model organism Bacillus subtilis as a heterologous host. Two fundamentally different regulators of E. faecalis resistance against cell wall antibiotics, the bacitra...

75 FR 21686 - Self-Regulatory Organizations; Financial Industry Regulatory Authority, Inc.; Notice of Filing of...

Science.gov (United States)

2010-04-26

... to pay arbitration awards to remain in the securities industry presents regulatory risks and is...-Regulatory Organizations; Financial Industry Regulatory Authority, Inc.; Notice of Filing of Proposed Rule... Regulatory Authority, Inc. (``FINRA'') filed with the Securities and Exchange Commission (``SEC'' or...

Cerebrovascular plaque segmentation using object class uncertainty snake in MR images

Science.gov (United States)

Das, Bipul; Saha, Punam K.; Wolf, Ronald; Song, Hee Kwon; Wright, Alexander C.; Wehrli, Felix W.

2005-04-01

Atherosclerotic cerebrovascular disease leads to formation of lipid-laden plaques that can form emboli when ruptured causing blockage to cerebral vessels. The clinical manifestation of this event sequence is stroke; a leading cause of disability and death. In vivo MR imaging provides detailed image of vascular architecture for the carotid artery making it suitable for analysis of morphological features. Assessing the status of carotid arteries that supplies blood to the brain is of primary interest to such investigations. Reproducible quantification of carotid artery dimensions in MR images is essential for plaque analysis. Manual segmentation being the only method presently makes it time consuming and sensitive to inter and intra observer variability. This paper presents a deformable model for lumen and vessel wall segmentation of carotid artery from MR images. The major challenges of carotid artery segmentation are (a) low signal-to-noise ratio, (b) background intensity inhomogeneity and (c) indistinct inner and/or outer vessel wall. We propose a new, effective object-class uncertainty based deformable model with additional features tailored toward this specific application. Object-class uncertainty optimally utilizes MR intensity characteristics of various anatomic entities that enable the snake to avert leakage through fuzzy boundaries. To strengthen the deformable model for this application, some other properties are attributed to it in the form of (1) fully arc-based deformation using a Gaussian model to maximally exploit vessel wall smoothness, (2) construction of a forbidden region for outer-wall segmentation to reduce interferences by prominent lumen features and (3) arc-based landmark for efficient user interaction. The algorithm has been tested upon T1- and PD- weighted images. Measures of lumen area and vessel wall area are computed from segmented data of 10 patient MR images and their accuracy and reproducibility are examined. These results correspond

Stories with and about wall carpets. An anthropological account on the inhabitation of Ursari Romanian Roma

Directory of Open Access Journals (Sweden)

Andreea Racleş

2014-12-01

Full Text Available The aim of this paper is to discuss the ways in which objects assist us in telling small stories about our positions in relation to our inhabited space, but also in relation to perceived dichotomised categories like us-others, the modern-the outmoded, civilized-backward. Acknowledging that narratives emerge from interactions between people, this paper is an attempt to show that an important role in the emergence of stories is played by interactions between people and objects. The wall carpets hung by Ursari Roma from a north-eastern Romanian town and the stories developed with and about these items constitute the main focus of this analysis. From an anthropological and material culture perspective, wall carpets are discussed as material presences in storytelling events and as objects of experience-centred stories that assist Roma people in negotiating and enacting their identities and belongings. Taking a cue from Georgakopoulou, who argues that narratives count on both discourses and activities (2007, home making practices and domestic activities (such as those related to the maintenance of the wall carpets are essential to this paper, as they enable an understanding of the “performative narrative of daily life” (Langellier 2004. The analysis is based on ethnographic material collected in 2014 in the aforementioned community, while the unit of analysis consists of excerpts from discussions with two Roma families, which became storytelling episodes.

The effect of wall geometry in particle-laden turbulent flow

Science.gov (United States)

Abdehkakha, Hoora; Iaccarino, Gianluca

2016-11-01

Particle-laden turbulent flow plays a significant role in various industrial applications, as turbulence alters the exchange of momentum and energy between particles and fluid flow. In wall-bounded flows, inhomogeneity in turbulent properties is the primary cause of turbophoresis that leads the particles toward the walls. Conversely, shear-induced lift force on the particles can become important if large scale vortical structures are present. The objective of this study is to understand the effects of geometry on fluid flows and consequently on particles transport and concentration. Direct numerical simulations combined with point particle Lagrangian tracking are performed for several geometries such as a pipe, channel, square duct, and squircle (rounded-corners duct). In non-circular ducts, anisotropic and inhomogeneous Reynolds stresses are the most influential phenomena that produce the secondary flows. It has been shown that these motions can have a significant impact on transporting momentum, vorticity, and energy from the core of the duct to the corners. The main focus of the present study is to explore the effects of near the wall structures and secondary flows on turbophoresis, lift, and particle concentration.

Deformation Measurements of Gabion Walls Using Image Based Modeling

Directory of Open Access Journals (Sweden)

Marek Fraštia

2014-06-01

Full Text Available The image based modeling finds use in applications where it is necessary to reconstructthe 3D surface of the observed object with a high level of detail. Previous experiments showrelatively high variability of the results depending on the camera type used, the processingsoftware, or the process evaluation. The authors tested the method of SFM (Structure fromMotion to determine the stability of gabion walls. The results of photogrammetricmeasurements were compared to precise geodetic point measurements.

Build an Interactive Word Wall

Science.gov (United States)

Jackson, Julie

2018-01-01

Word walls visually display important vocabulary covered during class. Although teachers have often been encouraged to post word walls in their classrooms, little information is available to guide them. This article describes steps science teachers can follow to transform traditional word walls into interactive teaching tools. It also describes a…

75 FR 5157 - Self-Regulatory Organizations; Financial Industry Regulatory Authority, Inc.; Order Approving...

Science.gov (United States)

2010-02-01

...-Regulatory Organizations; Financial Industry Regulatory Authority, Inc.; Order Approving Proposed Rule Change... Consolidated FINRA Rulebook January 25, 2010. On December 2, 2009, the Financial Industry Regulatory Authority... later in the rulebook consolidation process. It is therefore ordered, pursuant to Section 19(b)(2) of...

77 FR 47470 - Self-Regulatory Organizations; Financial Industry Regulatory Authority, Inc.; Notice of...

Science.gov (United States)

2012-08-08

...-Regulatory Organizations; Financial Industry Regulatory Authority, Inc.; Notice of Withdrawal of Proposed Rule Change To Adopt FINRA Rule 2231 (Customer Account Statements) in the Consolidated FINRA Rulebook August 2, 2012. On April 22, 2009, the Financial Industry Regulatory Authority, Inc. (``FINRA'') (f/k/a...

76 FR 21084 - Self-Regulatory Organizations; Financial Industry Regulatory Authority, Inc.; Notice of...

Science.gov (United States)

2011-04-14

... Securities April 8, 2011. I. Introduction On March 3, 2011, the Financial Industry Regulatory Authority, Inc... SECURITIES AND EXCHANGE COMMISSION [Release No. 34-64283; File No. SR-FINRA-2011-012] Self-Regulatory Organizations; Financial Industry Regulatory Authority, Inc.; Notice of Designation of a Longer...

Experimental Study of Multi-Walled Composite Shell Fragments under Thermal Force Effects

Directory of Open Access Journals (Sweden)

L. P. Tairova

2015-01-01

Full Text Available Multi-walled composite shells are a relatively new prospective type of load carrying structures for rocket and space engineering. These CFRP structures are produced by injection and infusion methods and have several advantages in comparison with common structures such as stringer-frame, grid and sandwich structures with a light core. In particular, those have more structural parameters, which enable one to control mechanical properties of the structure, and this is important in designing the load carrying structures of different purpose.Presently, there are few national and foreign publications on experimental investigations of mechanical properties of multi-walled shells. That is why the objective of the paper is to conduct the experimental study of deformation and failure processes of a multi-walled panel both under steady-state heating and under unsteady-state one.The paper presents the results of two tests: (1 the study of deformation and failure modes under compression and complete heating up to a specified temperature and (2 validation of working capability of multi-walled samples under single-side heating and compression simulating a start and flight version of the “ Proton” launch vehicle.Experimental results have shown that average elastic properties of multi-walled samples slightly depend on temperature for the studied range (from room temperature up to 195C while strength properties considerably decrease with increasing temperature, and this is typical for CFRP structures under compression. However, under unsteady-state short-term heating the structure has a strength that exceeds the minimal necessary strength of load carrying structures of the “Proton” launch vehicle (the samples satisfy simulated start conditions of the “Proton” launch vehicle. This is because of a low heat conductivity of the multi-walled core: an unheated sheet holds a low temperature and high load carrying capacity.Obtained results can be used in

Near wall combustion modeling in spark ignition engines. Part A: Flame–wall interaction

International Nuclear Information System (INIS)

Demesoukas, Sokratis; Caillol, Christian; Higelin, Pascal; Boiarciuc, Andrei; Floch, Alain

2015-01-01

Highlights: • A model for flame–wall interaction in addition to flame wrinkling by turbulence is proposed. • Two sparkplug positions and two lengths are used in a test engine for model validation. • Flame–wall interaction decreases the maximum values of cylinder pressure and heat release rates. • The impact of combustion chamber geometry is taken into account by the flame–wall interaction model. - Abstract: Research and design in the field of spark ignition engines seek to achieve high performance while conserving fuel economy and low pollutant emissions. For the evaluation of various engine configurations, numerical simulations are favored, since they are quick and less expensive than experiments. Various zero-dimensional combustion models are currently used. Both flame front reactions and post-flame processes contribute to the heat release rate. The first part of this study focuses on the role of the flame front on the heat release rate, by modeling the interaction of the flame front with the chamber wall. Post-flame reactions are dealt with in Part B of the study. The basic configurations of flame quenching in laminar flames are also applicable in turbulent flames, which is the case in spark ignition engines. A simplified geometric model of the combustion chamber was used to calculate the mean flame surface, the flame volume and the distribution of flame surface as a function of the distance from the wall. The flame–wall interaction took into account the geometry of the combustion chamber and of the flame, aerodynamic turbulence and the in-cylinder pressure and temperature conditions, through a phenomenological attenuation function of the wrinkling factor. A modified global wrinkling factor as a function of the mean surface distance distribution from the wall was calculated. The impact of flame–wall interaction was simulated for four configurations of the sparkplug position and length: centered and lateral position, and standard and projected

Self-Regulatory Processes Mediate the Intention-Behavior Relation for Adherence and Exercise Behaviors

NARCIS (Netherlands)

Bruin, de M.; Sheeran, P.; Kok, G.; Hiemstra, A.; Prins, J.M.; Hospers, H.J.; Breukelen, G.J.P.

2012-01-01

Objectives: Understanding the gap between people's intentions and actual health behavior is an important issue in health psychology. Our aim in this study was to investigate whether self-regulatory processes (monitoring goal progress and responding to discrepancies) mediate the intention-behavior

Managing Regulatory Body Competence

International Nuclear Information System (INIS)

2013-01-01

In 2001, the IAEA published TECDOC 1254, which examined the way in which the recognized functions of a regulatory body for nuclear facilities results in competence needs. Using the systematic approach to training (SAT), TECDOC 1254 provided a framework for regulatory bodies for managing training and developing and their maintaining their competence. It has been successfully used by many regulators. The IAEA has also introduced a methodology and an assessment tool - Guidelines for Systematic Assessment of Regulatory Competence Needs (SARCoN) - which provides practical guidance on analysing the training and development needs of a regulatory body and, through a gap analysis, guidance on establishing competence needs and how to meet them. In 2009, the IAEA established a steering committee (supported by a bureau) with the mission to advise the IAEA on how it could best assist Member States to develop suitable competence management systems for their regulatory bodies. The committee recommended the development of a safety report on managing staff competence as an integral part of a regulatory body's management system. This Safety Report was developed in response to this request. It supersedes TECDOC 1254, broadens its application to regulatory bodies for all facilities and activities, and builds upon the experience gained through the application of TECDOC 1254 and SARCoN and the feedback received from Member States. This Safety Report applies to the management of adequate competence as needs change, and as such is equally applicable to the needs of States 'embarking' on a nuclear power programme. It also deals with the special case of building up the competence of regulatory bodies as part of the overall process of establishing an 'embarking' State's regulatory system

Croatian energy regulatory council - independent Croatian regulatory body

International Nuclear Information System (INIS)

Klepo, M.

2002-01-01

By means of approving five energy laws, the Republic of Croatia established an appropriate legislative framework for energy sector regulation. A series of sub-law acts is presently being elaborated as well as some additional documents in order to bring about transparent and non-discriminatory provisions for the establishment of electric energy, gas, oil/oil derivatives and thermal energy markets, i.e. for the introduction and management of market activities and public services. A considerable share of these activities relates to the definition of transparent regulatory mechanisms that would guarantee the implementation of regulation rules based on the law, and be carried out by the independent regulatory body - Croatian Energy Regulatory Council. The Council's rights and obligations include firm executive functions, which present obligations to every energy entity. A dissatisfied party may set in motion a settlement of dispute, if it maintains that the decisions are not based on the law or reveal a flaw in the procedure. Therefore, it is the Council's priority to always make careful and law-abiding decisions. This paper gives insight into the regulatory framework elements based on the laws including the Council's organisational structure and non-profit entities that will prepare act proposals for the Council and perform other professional activities. (author)

The Interaction Features of the Multi-Level Retaining Walls with Soil Mass

Science.gov (United States)

Boyko, Igor; Skochko, Liudmyla; Zhuk, Veronica

2017-09-01

The interaction features of multi-level retaining walls with soil base were researched by changing their geometric parameters and locality at the plan. During excavation of deep foundation pits it is important to choose the type of constructions which influences on the horizontal displacements. The distance between the levels of retaining walls should be based on the results of numerical modelling. The objective of this paper is to present a comparison between the data of numerical simulations and the results of the in-situ lateral tests of couple piles. The problems have been solved by using the following soil models: Coulomb-Mohr model; model, which is based on the dilatation theory; elastic-plastic model with variable stiffness parameters.

First wall of thermonuclear device

International Nuclear Information System (INIS)

Kizawa, Makoto; Koizumi, Makoto; Nishihara, Yoshihiro.

1990-01-01

The first wall of a thermonuclear device is constituted with inner wall tiles, e.g. made of graphite and metal substrates for fixing them. However, since the heat expansion coefficient is different between the metal substrates and intermediate metal members, thermal stresses are caused to deteriorate the endurance of the inner wall tiles. In view of the above, low melting metals are disposed at the portion of contact between the inner wall tiles and the metal substrates and, further, a heat pipe structure is incorporated into the metal substrates. Under the thermal load, for example, during operation of the thermonuclear device, the low melting metals at the portion of contact are melted into liquid metals to enhance the state of contact between the inner wall tiles and the metal substrate to reduce the heat resistance and improve the heat conductivity. Even if there is a difference in the heat expansion coefficient between the inner wall tiles and the metal substrates, neither sharing stresses not thermal stresses are caused. Further, since the heat pipe structure is incorporated into the metal substrates, the lateral unevenness of the temperature in the metal substrates can be eliminated. Thus, the durability of the inner wall tiles can be improved. (N.H.)

Influence of Slip Condition on Unsteady Free Convection Flow of Viscous Fluid with Ramped Wall Temperature

Directory of Open Access Journals (Sweden)

Sami Ul Haq

2015-01-01

Full Text Available The objective of this study is to explore the influence of wall slip condition on a free convection flow of an incompressible viscous fluid with heat transfer and ramped wall temperature. Exact solution of the problem is obtained by using Laplace transform technique. Graphical results to see the effects of Prandtl number Pr, time t, and slip parameter η on velocity and skin friction for the case of ramped and constant temperature of the plate are provided and discussed.

A Novel Plasma Membrane-Anchored Protein Regulates Xylem Cell-Wall Deposition through Microtubule-Dependent Lateral Inhibition of Rho GTPase Domains.

Science.gov (United States)

Sugiyama, Yuki; Wakazaki, Mayumi; Toyooka, Kiminori; Fukuda, Hiroo; Oda, Yoshihisa

2017-08-21

Spatial control of cell-wall deposition is essential for determining plant cell shape [1]. Rho-type GTPases, together with the cortical cytoskeleton, play central roles in regulating cell-wall patterning [2]. In metaxylem vessel cells, which are the major components of xylem tissues, active ROP11 Rho GTPases form oval plasma membrane domains that locally disrupt cortical microtubules, thereby directing the formation of oval pits in secondary cell walls [3-5]. However, the regulatory mechanism that determines the planar shape of active Rho of Plants (ROP) domains is still unknown. Here we show that IQD13 associates with cortical microtubules and the plasma membrane to laterally restrict the localization of ROP GTPase domains, thereby directing the formation of oval secondary cell-wall pits. Loss and overexpression of IQD13 led to the formation of abnormally round and narrow secondary cell-wall pits, respectively. Ectopically expressed IQD13 increased the presence of parallel cortical microtubules by promoting microtubule rescue. A reconstructive approach revealed that IQD13 confines the area of active ROP domains within the lattice of the cortical microtubules, causing narrow ROP domains to form. This activity required the interaction of IQD13 with the plasma membrane. These findings suggest that IQD13 positively regulates microtubule dynamics as well as their linkage to the plasma membrane, which synergistically confines the area of active ROP domains, leading to the formation of oval secondary cell-wall pits. This finding sheds light on the role of microtubule-plasma membrane linkage as a lateral fence that determines the planar shape of Rho GTPase domains. Copyright © 2017 Elsevier Ltd. All rights reserved.

Domain wall engineering through exchange bias

International Nuclear Information System (INIS)

Albisetti, E.; Petti, D.

2016-01-01

The control of the structure and position of magnetic domain walls is at the basis of the development of different magnetic devices and architectures. Several nanofabrication techniques have been proposed to geometrically confine and shape domain wall structures; however, a fine tuning of the position and micromagnetic configuration is hardly achieved, especially in continuous films. This work shows that, by controlling the unidirectional anisotropy of a continuous ferromagnetic film through exchange bias, domain walls whose spin arrangement is generally not favored by dipolar and exchange interactions can be created. Micromagnetic simulations reveal that the domain wall width, position and profile can be tuned by establishing an abrupt change in the direction and magnitude of the exchange bias field set in the system. - Highlights: • Micromagnetic simulations study domain walls in exchange biased thin films. • Novel domain wall configurations can be stabilized via exchange bias. • Domain walls nucleate at the boundary of regions with different exchange bias. • Domain wall width and spin profile are controlled by tuning the exchange bias.

76 FR 63276 - Reducing Regulatory Burden; Retrospective Review Under E.O. 13563

Science.gov (United States)

2011-10-12

... submitted either via the Board's e-filing process or in the traditional paper format. Any person using e... objectives. The order also called for public participation in this regulatory process. Although Executive... Uniform Rail Costing System, which is the Board's general purpose costing methodology for the nation's...

Electricity generation: regulatory mechanisms to incentive renewable alternative energy sources in Brazil

International Nuclear Information System (INIS)

Cavaliero, Carla Kazue Nakao; Silva, E.P. da

2005-01-01

The dissemination of renewable alternative energy sources for electricity generation has always being done through regulatory mechanisms, created and managed by the government of each country. Since these sources are more costly to generate, they have received incentives in response to worldwide environmental concerns, above all with regard to the reduction of CO 2 emissions. In Brazil, the electricity generation from renewable alternative sources is experiencing a new phase of growth. Until a short time ago, environmental appeal was the strongest incentive to these sources in Brazil but it was insufficient to attain its objective. With the electricity crisis and the rationing imposed in 2001, another important factor gained awareness: the need to diversify energy sources. Within this context, this work has the objective of analyzing the regulatory mechanisms recently developed to stimulate electricity generation from renewable alternative energy sources in Brazil by following the experience of other countries such as the United States, United Kingdom and Germany

Hyphal walls of isolated lichen fungi

International Nuclear Information System (INIS)

Galun, M.; Braun, A.; Frensdorff, A.; Galun, E.

1976-01-01

The hyphal walls of three mycobionts, isolated from the lichens Xanthoria parietina, Tornabenia intricata and Sarcogyne sp. were investigated by two techniques: microaudiography of fungal colonies exposed to radioactive carbohydrate precursors; and binding, in vivo, of fluorescein conjugated lectins to hyphal walls of such colonies. N-( 3 H) acetylglucosamine was readily incorporated into tips, young hyphal walls and septa of the three mycobionts and the free-living fungus Trichoderma viride, but not into Phytophthora citrophthora, indicating that chitin is a major component of the mycobionts' hyphal walls. All three mycobionts, but neither of the free-living fungi, incorporated ( 3 H) mannose and ( 3 H) mannitol into their hyphal walls. Fluorescein-conjugated wheat germ agglutinin was bound to the hyphal walls of the three mycobionts and T. viride, but not to the walls of P. citrophthora; the binding pattern was similar to the grain pattern obtained in audiographs after short N-( 3 H) acetylglucosamine labelling. As wheat germ agglutinin binds specifically to chitin oligomers, the lectin binding tests further confirmed that chitin is a mycobiont hyphal wall component. Binding characteristics of several fluorescein-conjugated lectins to the three mycobionts indicated that this technique can yield useful information concerning the chemical composition of hyphal wall surfaces. (orig./AJ) [de

Yeast casein kinase 2 governs morphology, biofilm formation, cell wall integrity, and host cell damage of Candida albicans.

Science.gov (United States)

Jung, Sook-In; Rodriguez, Natalie; Irrizary, Jihyun; Liboro, Karl; Bogarin, Thania; Macias, Marlene; Eivers, Edward; Porter, Edith; Filler, Scott G; Park, Hyunsook

2017-01-01

The regulatory networks governing morphogenesis of a pleomorphic fungus, Candida albicans are extremely complex and remain to be completely elucidated. This study investigated the function of C. albicans yeast casein kinase 2 (CaYck2p). The yck2Δ/yck2Δ strain displayed constitutive pseudohyphae in both yeast and hyphal growth conditions, and formed enhanced biofilm under non-biofilm inducing condition. This finding was further supported by gene expression analysis of the yck2Δ/yck2Δ strain which showed significant upregulation of UME6, a key transcriptional regulator of hyphal transition and biofilm formation, and cell wall protein genes ALS3, HWP1, and SUN41, all of which are associated with morphogenesis and biofilm architecture. The yck2Δ/yck2Δ strain was hypersensitive to cell wall damaging agents and had increased compensatory chitin deposition in the cell wall accompanied by an upregulation of the expression of the chitin synthase genes, CHS2, CHS3, and CHS8. Absence of CaYck2p also affected fungal-host interaction; the yck2Δ/yck2Δ strain had significantly reduced ability to damage host cells. However, the yck2Δ/yck2Δ strain had wild-type susceptibility to cyclosporine and FK506, suggesting that CaYck2p functions independently from the Ca+/calcineurin pathway. Thus, in C. albicans, Yck2p is a multifunctional kinase that governs morphogenesis, biofilm formation, cell wall integrity, and host cell interactions.

Thin walls in regions with vacuum energy

Energy Technology Data Exchange (ETDEWEB)

Garfinkle, D [Florida Univ., Gainesville, FL (USA). Dept. of Physics; Vuille, C [Embry-Riddle Aeronautical Univ., Prescott, AZ (USA). Dept. of Math/Physical Science

1989-12-01

The motion of a thin wall is treated in the case where the regions on either side of the wall have vacuum energy. This treatment generalises previous results involving domain walls in vacuum and also previous results involving the properties of false vacuum bubbles. The equation of state for a domain wall is{tau} = {sigma} where {tau} is the tension in the wall and {sigma} is the energy density. We consider the motion of a more general class of walls having equation of state {tau}{Gamma}{sigma} with 0{le}{Gamma}{le}1. Spherically symmetric and planar symmetric walls are examined. We also find the global structure of the wall spacetime. (author).

Anti-regulatory T cells

DEFF Research Database (Denmark)

Andersen, Mads Hald

2017-01-01

responses to tumours or inhibiting autoimmunity development. However, recent studies report the discovery of self-reactive pro-inflammatory T cells—termed anti-regulatory T cells (anti-Tregs)—that target immune-suppressive cells. Thus, regulatory cells can now be defined as both cells that suppress immune...... reactions as well as effector cells that counteract the effects of suppressor cells and support immune reactions. Self-reactive anti-Tregs have been described that specifically recognize human leukocyte antigen-restricted epitopes derived from proteins that are normally expressed by regulatory immune cells......Our initial understanding of immune-regulatory cells was based on the discovery of suppressor cells that assure peripheral T-cell tolerance and promote immune homeostasis. Research has particularly focused on the importance of regulatory T cells (Tregs) for immune modulation, e.g. directing host...

12 CFR 562.2 - Regulatory reports.

Science.gov (United States)

2010-01-01

... § 562.2 Regulatory reports. (a) Definition and scope. This section applies to all regulatory reports, as... (TFR) are examples of regulatory reports. Regulatory reports are regulatory documents, not accounting... limited to, the accounting instructions provided in the TFR, guidance contained in OTS regulations...

Plasma-wall interaction

International Nuclear Information System (INIS)

Reichle, R.

2004-01-01

This document gathers the 43 slides presented in the framework of the week long lecture 'hot plasmas 2004' and dedicated to plasma-wall interaction in a tokamak. This document is divided into 4 parts: 1) thermal load on the wall, power extraction and particle recovery, 2) basic edge plasma physics, 3) processes that drive the plasma-solid interaction, and 4) material conditioning (surface treatment...) for ITER

Reconstitution of a secondary cell wall in a secondary cell wall-deficient Arabidopsis mutant.

Science.gov (United States)

Sakamoto, Shingo; Mitsuda, Nobutaka

2015-02-01

The secondary cell wall constitutes a rigid frame of cells in plant tissues where rigidity is required. Deposition of the secondary cell wall in fiber cells contributes to the production of wood in woody plants. The secondary cell wall is assembled through co-operative activities of many enzymes, and their gene expression is precisely regulated by a pyramidal cascade of transcription factors. Deposition of a transmuted secondary cell wall in empty fiber cells by expressing selected gene(s) in this cascade has not been attempted previously. In this proof-of-concept study, we expressed chimeric activators of 24 transcription factors that are preferentially expressed in the stem, in empty fiber cells of the Arabidopsis nst1-1 nst3-1 double mutant, which lacks a secondary cell wall in fiber cells, under the control of the NST3 promoter. The chimeric activators of MYB46, SND2 and ANAC075, as well as NST3, reconstituted a secondary cell wall with different characteristics from those of the wild type in terms of its composition. The transgenic lines expressing the SND2 or ANAC075 chimeric activator showed increased glucose and xylose, and lower lignin content, whereas the transgenic line expressing the MYB46 chimeric activator showed increased mannose content. The expression profile of downstream genes in each transgenic line was also different from that of the wild type. This study proposed a new screening strategy to identify factors of secondary wall formation and also suggested the potential of the artificially reconstituted secondary cell walls as a novel raw material for production of bioethanol and other chemicals. © The Author 2014. Published by Oxford University Press on behalf of Japanese Society of Plant Physiologists.

Increased numbers of CD5+ B lymphocytes with a regulatory phenotype in spondylarthritis

NARCIS (Netherlands)

Cantaert, Tineke; Doorenspleet, Marieke E.; Francosalinas, Gabriela; Paramarta, Jaqueline E.; Klarenbeek, Paul L.; Tiersma, Yvonne; van der Loos, Chris M.; de Vries, Niek; Tak, Paul Peter; Baeten, Dominique L.

2012-01-01

Objective Whether and how B lymphocytes contribute to the pathogenesis of spondylarthritis (SpA), a seronegative arthritis associated with gut inflammation, remains unknown. Because innate-like CD5+ B lymphocytes with regulatory functions have been identified in colitis models, we undertook the

Optimization of multiplane ?PIV for wall shear stress and wall topography characterization

NARCIS (Netherlands)

Rossi, M.; Lindken, R.; Westerweel, J.

2009-01-01

Multiplane ?PIV can be utilized to determine the wall shear stress and wall topology from the measured flow over a structured surface. A theoretical model was developed to predict the measurement error for the surface topography and shear stress, based on a theoretical analysis of the precision in

Review of decision methodologies for evaluating regulatory actions affecting public health and safety

International Nuclear Information System (INIS)

Hendrickson, P.L.; McDonald, C.L.; Schilling, A.H.

1976-12-01

This report examines several aspects of the problems and choices facing the governmental decision maker who must take regulatory actions with multiple decision objectives and attributes. Particular attention is given to the problems facing the U.S. Nuclear Regulatory Commission (NRC) and to the decision attribute of chief concern to NRC, the protection of human health and safety, with emphasis on nuclear power plants. The study was undertaken to provide background information for NRC to use in refining its process of value/impact assessment of proposed regulatory actions. The principal conclusion is that approaches to rationally consider the value and impact of proposed regulatory actions are available. These approaches can potentially improve the decision-making process and enable the agency to better explain and defend its decisions. They also permit consistent examination of the impacts, effects of uncertainty and sensitivity to various assumptions of the alternatives being considered. Finally, these approaches can help to assure that affected parties are heard and that technical information is used appropriately and to the extent possible. The principal aspects of the regulatory decision problem covered in the report are: the legal setting for regulatory decisions which affect human health and safety, elements of the decision-making process, conceptual approaches to decision making, current approaches to decision making in several Federal agencies, and the determination of acceptable risk levels

Contaminated Non-Food Products. Regulatory Deficit Regarding Contaminated Non-Food Products

International Nuclear Information System (INIS)

2015-11-01

An INES 7 event in Europe will generate tremendous amounts of class 7 goods. From roofing tile to motor cycle, everything becomes a surface contaminated object and therefore a dangerous good. Along with the classification as a dangerous good goes the classification as waste. Who would buy a commodity that cannot be shipped without special care? Thus, ADR/RID induce a de facto dose limit for commodities, whether intended or not. Within the present ADR/RID this regulatory checkmate can hardly be avoided. National exemptions are impossible and with a view to the European internal market even pointless. Here we present a harmonised description of this particular checkmate. We discuss two specific scenarios and the corresponding regulatory issues

Wall roughness induces asymptotic ultimate turbulence

Science.gov (United States)

Zhu, Xiaojue; Verschoof, Ruben A.; Bakhuis, Dennis; Huisman, Sander G.; Verzicco, Roberto; Sun, Chao; Lohse, Detlef

2018-04-01

Turbulence governs the transport of heat, mass and momentum on multiple scales. In real-world applications, wall-bounded turbulence typically involves surfaces that are rough; however, characterizing and understanding the effects of wall roughness on turbulence remains a challenge. Here, by combining extensive experiments and numerical simulations, we examine the paradigmatic Taylor-Couette system, which describes the closed flow between two independently rotating coaxial cylinders. We show how wall roughness greatly enhances the overall transport properties and the corresponding scaling exponents associated with wall-bounded turbulence. We reveal that if only one of the walls is rough, the bulk velocity is slaved to the rough side, due to the much stronger coupling to that wall by the detaching flow structures. If both walls are rough, the viscosity dependence is eliminated, giving rise to asymptotic ultimate turbulence—the upper limit of transport—the existence of which was predicted more than 50 years ago. In this limit, the scaling laws can be extrapolated to arbitrarily large Reynolds numbers.

Near-wall serpentine cooled turbine airfoil

Science.gov (United States)

Lee, Ching-Pang

2013-09-17

A serpentine coolant flow path (54A-54G) formed by inner walls (50, 52) in a cavity (49) between pressure and suction side walls (22, 24) of a turbine airfoil (20A). A coolant flow (58) enters (56) an end of the airfoil, flows into a span-wise channel (54A), then flows forward (54B) over the inner surface of the pressure side wall, then turns behind the leading edge (26), and flows back along a forward part of the suction side wall, then follows a loop (54E) forward and back around an inner wall (52), then flows along an intermediate part of the suction side wall, then flows into an aft channel (54G) between the pressure and suction side walls, then exits the trailing edge (28). This provides cooling matched to the heating topography of the airfoil, minimizes differential thermal expansion, revives the coolant, and minimizes the flow volume needed.

Thinner regions of intracranial aneurysm wall correlate with regions of higher wall shear stress: a 7.0 tesla MRI

Science.gov (United States)

Blankena, Roos; Kleinloog, Rachel; Verweij, Bon H.; van Ooij, Pim; ten Haken, Bennie; Luijten, Peter R.; Rinkel, Gabriel J.E.; Zwanenburg, Jaco J.M.

2016-01-01

Purpose To develop a method for semi-quantitative wall thickness assessment on in vivo 7.0 tesla (7T) MRI images of intracranial aneurysms for studying the relation between apparent aneurysm wall thickness and wall shear stress. Materials and Methods Wall thickness was analyzed in 11 unruptured aneurysms in 9 patients, who underwent 7T MRI with a TSE based vessel wall sequence (0.8 mm isotropic resolution). A custom analysis program determined the in vivo aneurysm wall intensities, which were normalized to signal of nearby brain tissue and were used as measure for apparent wall thickness (AWT). Spatial wall thickness variation was determined as the interquartile range in AWT (the middle 50% of the AWT range). Wall shear stress was determined using phase contrast MRI (0.5 mm isotropic resolution). We performed visual and statistical comparisons (Pearson’s correlation) to study the relation between wall thickness and wall shear stress. Results 3D colored AWT maps of the aneurysms showed spatial AWT variation, which ranged from 0.07 to 0.53, with a mean variation of 0.22 (a variation of 1.0 roughly means a wall thickness variation of one voxel (0.8mm)). In all aneurysms, AWT was inversely related to WSS (mean correlation coefficient −0.35, P<0.05). Conclusions A method was developed to measure the wall thickness semi-quantitatively, using 7T MRI. An inverse correlation between wall shear stress and AWT was determined. In future studies, this non-invasive method can be used to assess spatial wall thickness variation in relation to pathophysiologic processes such as aneurysm growth and –rupture. PMID:26892986

Regulatory practice for safety of nuclear energy in the German Democratic Republic

International Nuclear Information System (INIS)

Krueger, F.W.; Arndt, H.; Nessau, L.; Rabold, H.; Roehnsch, W.; Scheel, H.

1988-01-01

An outline of the regulatory practice applied in the GDR to ensure the safe use of nuclear energy is given in the form of answers to a questionnaire issued by the IAEA with the objective of giving the international community confidence in the safety of nuclear power programmes. (author)

75 FR 60157 - Self-Regulatory Organizations; Financial Industry Regulatory Authority, Inc.; Notice of Filing...

Science.gov (United States)

2010-09-29

...-Regulatory Organizations; Financial Industry Regulatory Authority, Inc.; Notice of Filing and Immediate..., 2010, Financial Industry Regulatory Authority, Inc. (``FINRA'') filed with the Securities and Exchange... information about the rulebook consolidation process, see Information Notice, March 12, 2008 (Rulebook...

Development of P4140 video data wall projector; Video data wall projector

Energy Technology Data Exchange (ETDEWEB)

Watanabe, H.; Inoue, H. [Toshiba Corp., Tokyo (Japan)

1998-12-01

The P4140 is a 3 cathode-ray tube (CRT) video data wall projector for super video graphics array (SVGA) signals. It is used as an image display unit, providing a large screen when several sets are put together. A high-quality picture has been realized by higher resolution and improved color uniformity technology. A new convergence adjustment system has also been developed through the optimal combination of digital and analog technologies. This video data wall installation has been greatly enhanced by the automation of cubes and cube performance settings. The P4140 video data wall projector can be used for displaying not only data but video as well. (author)

Regulatory decision making by decision analyses

International Nuclear Information System (INIS)

Holmberg, J.; Pulkkinen, U.

1993-11-01

The Technical Research Centre of Finland (VTT) has studied with the Finnish Centre for Radiation and Nuclear Safety (STUK) the applicability of decision analytic approach to the treatment of nuclear safety related problems at the regulatory body. The role of probabilistic safety assessment (PSA) in decision making has also been discussed. In the study, inspectors from STUK exercised with a decision analytic approach by reoperationalizing two occurred and solved problems. The research scientist from VTT acted as systems analysts guiding the analysis process. The first case was related to a common cause failure phenomenon in solenoid valves controlling pneumatic valves important to safety of the plant. The problem of the regulatory body was to judge whether to allow continued operation or to require more detailed inspections and in which time chedule the inspections should be done. The latter problem was to evaluate design changes of external electrical grid connections after a fire incident had revealed weakness in the separation of electrical system. In both cases, the decision analysis was carried out several sessions in which decision makers, technical experts as well as experts of decision analysis participated. A multi-attribute value function was applied as a decision model so that attributes had to be defined to quantify the levels of achievements of the objectives. The attributes included both indicators related to the level of operational safety of the plant such as core damage frequency given by PSA, and indicators related to the safety culture, i.e., how well the chosen option fits on the regulatory policy. (24 refs., 6 figs., 9 tabs.)

Inplane shear capacity of reinforced composite masonry block walls

International Nuclear Information System (INIS)

White, W.H.; Tseng, W.S.

1981-01-01

The objective of this paper is to describe a test program performed to determine the inplane shear capacity, stiffness and ductility of composite masonry walls subjected to earthquake type loadings. Specimens were simultaneously subjected to a range of compressive loads to simulate dead load; and inplane shear loads with full load reversal to simulate the earthquake cycling load. The influence of horizontal and vertical reinforcing steel percentages on the inplane shear capacity, stiffness and ductility was also investigated. (orig./HP)

76 FR 20759 - Self-Regulatory Organizations; Financial Industry Regulatory Authority, Inc.; Notice of Filing...

Science.gov (United States)

2011-04-13

...-Regulatory Organizations; Financial Industry Regulatory Authority, Inc.; Notice of Filing and Immediate..., 2011, Financial Industry Regulatory Authority, Inc. (``FINRA'') filed with the Securities and Exchange.... For more information about the rulebook consolidation process, see Information Notice, March 12, 2008...

76 FR 40412 - Self-Regulatory Organizations; Financial Industry Regulatory Authority, Inc.; Notice of Filing...

Science.gov (United States)

2011-07-08

...-Regulatory Organizations; Financial Industry Regulatory Authority, Inc.; Notice of Filing and Immediate..., Financial Industry Regulatory Authority, Inc. (``FINRA'') filed with the Securities and Exchange Commission... a more limited application by their terms. For more information about the rulebook consolidation...

75 FR 71164 - Self-Regulatory Organizations; Financial Industry Regulatory Authority, Inc.; Notice of Filing...

Science.gov (United States)

2010-11-22

...-Regulatory Organizations; Financial Industry Regulatory Authority, Inc.; Notice of Filing and Immediate..., 2010, Financial Industry Regulatory Authority, Inc. (``FINRA'') filed with the Securities and Exchange.... For more information about the rulebook consolidation process, see Information Notice, March 12, 2008...

77 FR 34379 - Notice of Joint Meeting of the Nuclear Regulatory Commission and the Federal Energy Regulatory...

Science.gov (United States)

2012-06-11

... DEPARTMENT OF ENERGY Federal Energy Regulatory Commission [Docket No. AD06-6-000] Notice of Joint Meeting of the Nuclear Regulatory Commission and the Federal Energy Regulatory Commission The Federal Energy Regulatory Commission (FERC) and the Nuclear Regulatory Commission (NRC) will hold a joint meeting...

Etonogestrel implant migration to the vasculature, chest wall, and distant body sites: cases from a pharmacovigilance database.

Science.gov (United States)

Kang, Sarah; Niak, Ali; Gada, Neha; Brinker, Allen; Jones, S Christopher

2017-12-01

To describe clinical outcomes of etonogestrel implant patients with migration to the vasculature, chest wall and other distant body sites spontaneously reported to the US Food and Drug Administration Adverse Event Reporting System (FAERS) database. We performed a standardized Medical Dictionary for Regulatory Activities (MedDRA) query in the FAERS database (through November 15, 2015), with reports coded with one or more MedDRA preferred terms that indicate complications with device placement or migration of the device from the original site of insertion to the vasculature, chest wall and other distant body sites. We excluded any cases previously described in the medical literature. We identified 38 cases of pronounced etonogestrel implant migration. Migration locations included the lung/pulmonary artery (n=9), chest wall (n=1), vasculature at locations other than the lung/pulmonary artery (n=14) and extravascular migrations (n=14) to other body sites (e.g., the axilla and clavicle/neck line/shoulder). The majority of cases were asymptomatic and detected when the patient desired implant removal; however, seven cases reported symptoms such as pain, discomfort and dyspnea in association with implant migration. Three cases also describe pulmonary fibrosis and skin reactions as a result of implant migration to the vasculature, chest wall and other distant body sites. Sixteen cases reported surgical removal in an operating room setting. Our FAERS case series demonstrates etonogestrel implant migration to the vasculature, chest wall and other body sites distant from the site of original insertion. As noted by the sponsor in current prescribing information, a key determinant in the risk for etonogestrel contraceptive implant migration appears to be improper insertion technique. Although migration of etonogestrel implants to the vasculature is rare, awareness of migration and education on proper insertion technique may reduce the risk. Published by Elsevier Inc.

Mapping regulatory models for medicinal cannabis: a matrix of options.

Science.gov (United States)

Belackova, Vendula; Shanahan, Marian; Ritter, Alison

2017-05-30

Objective The aim of the present study was to develop a framework for assessing regulatory options for medicinal cannabis in Australia. Methods International regulatory regimes for medicinal cannabis were reviewed with a qualitative policy analysis approach and key policy features were synthesised, leading to a conceptual framework that facilitates decision making across multiple dimensions. Results Two central organising dimensions of medicinal cannabis regulation were identified: cannabis supply and patient authorisation (including patient access). A number of the different supply options can be matched with a number of different patient authorisation options, leading to a matrix of possible regulatory regimes. Conclusions The regulatory options, as used internationally, involve different forms of cannabis (synthetic and plant-based pharmaceutical preparations or herbal cannabis) and the varying extent to which patient authorisation policies and procedures are stringently or more loosely defined. The optimal combination of supply and patient authorisation options in any jurisdiction that chooses to make medicinal cannabis accessible will depend on policy goals. What is known about the topic? Internationally, regulation of medicinal cannabis has developed idiosyncratically, depending on formulations that were made available and local context. There has been no attempt to date in the scientific literature to systematically document the variety of regulatory possibilities for medicinal cannabis. What does this paper add? This paper presents a new conceptual schema for considering options for the regulation of medicinal cannabis, across both supply and patient authorisation aspects. What are the implications for practitioners? The design of regulatory systems in Australia, whether for pharmaceutical or herbal products, is a vital issue for policy makers right now as federal and state and territory governments grapple with the complexities of medicinal cannabis

Effects of natalizumab treatment on Foxp3+ T regulatory cells.

Science.gov (United States)

Stenner, Max-Philipp; Waschbisch, Anne; Buck, Dorothea; Doerck, Sebastian; Einsele, Hermann; Toyka, Klaus V; Wiendl, Heinz

2008-10-06

Natalizumab, a monoclonal humanized antibody targeting the alpha-4 chain of very late activation antigen 4 (VLA-4) exerts impressive therapeutic effects in patients with relapsing-remitting multiple sclerosis. Our objective was to study impacts of Natalizumab therapy on Foxp3+ T regulatory cells (Tregs) in multiple sclerosis (MS) patients. A combined approach of in vitro and ex vivo experiments using T cells isolated from the peripheral blood of healthy donors and Natalizumab treated MS patients was chosen. We determined binding of Natalizumab and its effects on the frequency, transmigratory behaviour and suppressive function of Tregs. Binding of Natalizumab and expression of CD49d (alpha-4 chain of VLA-4) differed between non-regulatory and regulatory cells. Albeit Foxp3+ Tregs had lower levels of CD49d, Natalizumab blocked the transmigration of Foxp3+ Tregs similar to non-regulatory T cells. The frequency of peripheral blood Tregs was unaffected by Natalizumab treatment. Natalizumab does not alter the suppressive capacity of CD4+CD25(high)CD127(low)Foxp3+ Tregs under in vitro conditions. Furthermore, the impaired function of Tregs in MS patients is not restored by Natalizumab treatment. We provide a first detailed analysis of Natalizumab effects on the regulatory T cell population. Our prospective study shows that Foxp3+ Tregs express lower levels of VLA-4 and bind less Natalizumab. We further the understanding of the mechanisms of action of Natalizumab by demonstrating that unlike other immunomodulatory drugs the beneficial therapeutic effects of the monoclonal antibody are largely independent of alterations in Treg frequency or function.

The Regulatory Cooperation Forum, an Opportunity to Strengthen International Cooperation

International Nuclear Information System (INIS)

Lachaume, J.L.; Mamoru, M.

2016-01-01

The Regulatory Cooperation Forum (RCF) is a member-driven forum of nuclear power regulators created in 2010 that promotes the sharing of regulatory knowledge and experience through international cooperation and collaboration using the IAEA Safety Standards as its basis. The RCF involves countries with advanced nuclear power programmes, countries embarking on nuclear power for the first time and countries with smaller programmes considering expansion. The primary objectives of the RCF are: • To promote collaboration and cooperation among RCF members to improve coordination of support for regulatory infrastructure development; • To contribute to achieving and sustaining a high level of nuclear safety, consistent with the IAEA Safety Standards and Guidance; • To optimize resources among RCF members and avoid unnecessary support duplication through improved coordination. Membership of the RCF is open to all Member States of the IAEA. Participants in RCF activities will normally be senior representatives from regulatory bodies in Member States and from other providers, including the IAEA, European Commission (EC) and the Nuclear Energy Agency (NEA) of the Organization for Economic Co-operation and Development (OECD). So far, more than 30 countries are members of the RCF. The RCF has developed Action Plans to support Jordan, Vietnam, Belarus and Poland. The IAEA’s Nuclear Safety Action Plan urges Member States to strengthen the effectiveness of national regulatory bodies as well as base the development of their nuclear infrastructures on IAEA Safety Standards. The RCF assists Member States in implementing both of these actions for embarking, existing and expanding nuclear programmes. (author)

Modulating activity of vancomycin and daptomycin on the expression of autolysis cell-wall turnover and membrane charge genes in hVISA and VISA strains.

Directory of Open Access Journals (Sweden)

Viviana Cafiso

Full Text Available Glycopeptides are still the gold standard to treat MRSA (Methicillin Resistant Staphylococcus aureus infections, but their widespread use has led to vancomycin-reduced susceptibility [heterogeneous Vancomycin-Intermediate-Staphylococcus aureus (hVISA and Vancomycin-Intermediate-Staphylococcus aureus (VISA], in which different genetic loci (regulatory, autolytic, cell-wall turnover and cell-envelope positive charge genes are involved. In addition, reduced susceptibility to vancomycin can influence the development of resistance to daptomycin. Although the phenotypic and molecular changes of hVISA/VISA have been the focus of different papers, the molecular mechanisms responsible for these different phenotypes and for the vancomycin and daptomycin cross-resistance are not clearly understood. The aim of our study was to investigate, by real time RT-PCR, the relative quantitative expression of genes involved in autolysis (atl-lytM, cell-wall turnover (sceD, membrane charges (mprF-dltA and regulatory mechanisms (agr-locus-graRS-walKR, in hVISA and VISA cultured with or without vancomycin and daptomycin, in order to better understand the molecular basis of vancomycin-reduced susceptibility and the modulating activity of vancomycin and daptomycin on the expression of genes implicated in their reduced susceptibility mechanisms. Our results show that hVISA and VISA present common features that distinguish them from Vancomycin-Susceptible Staphylococcus aureus (VSSA, responsible for the intermediate glycopeptide resistance i.e. an increased cell-wall turnover, an increased positive cell-wall charge responsible for a repulsion mechanism towards vancomycin and daptomycin, and reduced agr-functionality. Indeed, VISA emerges from hVISA when VISA acquires a reduced autolysis caused by a down-regulation of autolysin genes, atl/lytM, and a reduction of the net negative cell-envelope charge via dltA over-expression. Vancomycin and daptomycin, acting in a similar

76 FR 60106 - Self-Regulatory Organizations; Financial Industry Regulatory Authority, Inc.; Notice of Filing...

Science.gov (United States)

2011-09-28

...-Regulatory Organizations; Financial Industry Regulatory Authority, Inc.; Notice of Filing and Immediate... 14, 2011, Financial Industry Regulatory Authority, Inc. (``FINRA'') (f/k/a National Association of.... For more information about the rulebook consolidation process, see Information Notice, March 12, 2008...

75 FR 41254 - Self-Regulatory Organizations; Financial Industry Regulatory Authority, Inc.; Order Approving a...

Science.gov (United States)

2010-07-15

... registered capacity, may work in other investment-related industries, such as financial planning, or may seek...-Regulatory Organizations; Financial Industry Regulatory Authority, Inc.; Order Approving a Proposed Rule..., 2010, the Financial Industry Regulatory Authority, Inc. (``FINRA'') filed with the Securities and...

COMPARISON OF SENSORS FOR RESISTIVE WALL MODE FEEDBACK CONTROL. MILESTONE No.145 ''CONTAINING PLASMA INSTABILITIES WITH METAL WALLS''

International Nuclear Information System (INIS)

STRAIT, E.J.; CHU, M.S.; GAROFALO, A.M.; LAHAYE, R.J.; OKABAYASHI, M.; REIMERDES, H.; SCOVILLE, J.T.; TURNBULL, A.D.

2002-01-01

OAK A271 COMPARISON OF SENSORS FOR RESISTIVE WALL MODE FEEDBACK CONTROL MILESTONE No.145 CONTAINING PLASMA INSTABILITIES WITH METAL WALLS. The most serious instabilities in the tokamak are those described by ideal magneto-hydrodynamic theory. These modes limit the stable operating space of the tokamak. The ideal MHD calculations predict the stable operating space of the tokamak may be approximately doubled when a perfectly conducting metal wall is placed near the plasma boundary, compared to the case with no wall (free boundary). The unstable mode distortions of the plasma column cannot bulge out through a perfectly conducting wall. However, real walls have finite conductivity and when plasmas are operated in the regime between the free boundary stability limit and the perfectly conducting wall limit, the unstable mode encountered in that case the resistive wall mode, can leak out through the metal wall, allowing the mode to keep slowly growing. The slow growth affords the possibility of feedback stabilizing this mode with external coils. DIII-D is making good progress in such feedback stabilization research and in 2002 will use an improved set of mode sensors inside the vacuum vessel and closer to the plasma surface which are expected theoretically to improve the ability to stabilize the resistive wall mode

Diurnal Periodicity in the Supply of Cell Wall Components during Wood Cell Wall Formation

OpenAIRE

細尾, 佳宏

2012-01-01

This review summarizes recent studies on the diurnal periodicity in wood cell wall formation, with a major focus on those that we have conducted. Differences in the innermost surface of developing secondary walls of differentiating conifer tracheids can be seen from day to night Cellulose microfibrils are clearly evident during the day, and amorphous material containing abundant hemicelluloses is prevalent at night. These findings suggest a diurnal periodicity in the supply of cell wall compo...

Mid-infrared pulsed laser ablation of the arterial wall. Mechanical origin of "acoustic" wall damage and its effect on wall healing

NARCIS (Netherlands)

van Erven, L.; van Leeuwen, T. G.; Post, M. J.; van der Veen, M. J.; Velema, E.; Borst, C.

1992-01-01

Pulsed mid-infrared lasers are an alternative to excimer lasers for transluminal angioplasty. The mid-infrared lasers, however, were reported to produce "acoustic" wall damage that might impair the immediate and long-term results. To study the immediate and long-term effects on the arterial wall,

Turbine airfoil with outer wall thickness indicators

Science.gov (United States)

Marra, John J; James, Allister W; Merrill, Gary B

2013-08-06

A turbine airfoil usable in a turbine engine and including a depth indicator for determining outer wall blade thickness. The airfoil may include an outer wall having a plurality of grooves in the outer surface of the outer wall. The grooves may have a depth that represents a desired outer surface and wall thickness of the outer wall. The material forming an outer surface of the outer wall may be removed to be flush with an innermost point in each groove, thereby reducing the wall thickness and increasing efficiency. The plurality of grooves may be positioned in a radially outer region of the airfoil proximate to the tip.

Finite element modeling of single-walled carbon nanotubes with introducing a new wall thickness

International Nuclear Information System (INIS)

Jalalahmadi, B; Naghdabadi, R

2007-01-01

A three-dimensional finite element (FE) model for armchair, zigzag and chiral single-walled carbon nanotubes (SWCNTs) is proposed. By considering the covalent bonds as connecting elements between carbon atoms, a nanotube is simulated as a space frame-like structure. Here, the carbon atoms act as joints of the connecting elements. To create the FE models, nodes are placed at the locations of carbon atoms and the bonds between them are modeled using three-dimensional elastic beam elements. Using Morse atomic potential, the elastic moduli of beam elements are obtained via considering a linkage between molecular and continuum mechanics. Also, a new wall thickness ( bond diameter) equal to 0.1296 nm is introduced. In order to demonstrate the applicability of FE model and new wall thickness, the influence of tube wall thickness, diameter and chirality on the Young's modulus of SWCNTs is investigated. It is found that the choice of wall thickness significantly affects the calculation of Young's modulus. For the values of wall thickness used in the literature, the Young's moduli are estimated which agree very well with the corresponding theoretical results and experimental measurements. We also investigate the dependence of elastic moduli on diameter and chirality of the nanotube. The larger tube diameter, the higher Young's modulus of SWCNT. The Young's modulus of chiral SWCNTs is found to be generally larger than that of armchair and zigzag SWCNTs. The presented results demonstrate that the proposed FE model and wall thickness may provide a valuable tool for studying the mechanical behavior of carbon nanotubes and their application in nano-composites

Fusion: first wall problems

International Nuclear Information System (INIS)

Behrisch, R.

1976-01-01

Some of the relevant elementary atomic processes which are expected to be of significance to the first wall of a fusion reactor are reviewed. Up to the present, most investigations have been performed at relatively high ion energies, typically E greater than 5 keV, and even in this range the available data are very poor. If the plasma wall interaction takes place at energies of E greater than 1 keV the impurity introduction and first wall erosion which will take place predominantly by sputtering, will be large and may severely limit the burning time of the plasma. The wall bombardment and surface erosion will presumably not decrease substantially by introducing a divertor. The erosion can only be kept low if the energy of the bombarding ions and neutrals can be kept below the threshold for sputtering of 1 to 10 eV. 93 refs

Future nuclear regulatory challenges

International Nuclear Information System (INIS)

Royen, J.

1998-01-01

In December 1996, the NEA Committee on Nuclear Regulatory Activities concluded that changes resulting from economic deregulation and other recent developments affecting nuclear power programmes have consequences both for licensees and regulatory authorities. A number of potential problems and issues which will present a challenge to nuclear regulatory bodies over the next ten years have been identified in a report just released. (author)

77 FR 7218 - Self-Regulatory Organizations; Financial Industry Regulatory Authority, Inc.; Notice of Filing...

Science.gov (United States)

2012-02-10

...-Regulatory Organizations; Financial Industry Regulatory Authority, Inc.; Notice of Filing and Immediate... thereunder,\\2\\ notice is hereby given that on January 30, 2012, Financial Industry Regulatory Authority, Inc.... For more information about the rulebook consolidation process, see Information Notice, March 12, 2008...

75 FR 59771 - Self-Regulatory Organizations; Financial Industry Regulatory Authority, Inc.; Order Approving the...

Science.gov (United States)

2010-09-28

...-Regulatory Organizations; Financial Industry Regulatory Authority, Inc.; Order Approving the Proposed Rule.... I. Introduction On July 27, 2010, the Financial Industry Regulatory Authority, Inc. (``FINRA'') (f/k... pertinent distribution-related information from its members in a timely fashion to facilitate its Regulation...

76 FR 50796 - Self-Regulatory Organizations; Financial Industry Regulatory Authority, Inc.; Notice of Filing...

Science.gov (United States)

2011-08-16

...-Regulatory Organizations; Financial Industry Regulatory Authority, Inc.; Notice of Filing and Immediate Effectiveness of Proposed Rule Change To Increase the Position Limit for Options on the Standard and Poor's... Financial Industry Regulatory Authority, Inc. (``FINRA'') filed with the Securities and Exchange Commission...

Ultrasonography of chest wall lesion

Energy Technology Data Exchange (ETDEWEB)

Park, Cheol Min; Kim, C. H.; Cha, I. H.; Chung, K. B.; Ser, W. H.; Choi, Y. H. [Seoul National University College of Medicine, Seoul (Korea, Republic of)

1989-12-15

Thirty-one patients with chest wall diseases were studied with ultrasound to evaluate its role in chest wall lesions. There were eight infectious conditions, 9 benign tumors, 11 malignant lesions and 3 miscellaneous cases. Diffuse chest wall thickening with heterogeneous echogenicity and obliteration of subcutaneous fat layer are findings of acute infection. In cases of tuberculous smpyema necessitates, pleural abnormality extended to the chest wall through intercostal space. Benign tumors were well demarcated, except in 4 cases of lipoma/lipomatosis. Malignant lesions showed irregular soft tissue masses, bone destruction, pleural effusion and subcutaneous invasion. Multiple enlarged lymph nodes were also shown. Ultrasound can demonstrate te internal structure, extent, depth and associated findings such as pleural effusion, bone destruction and peripheral lung involvement. Ultrasound is not only safe, non-invasive and an effective diagnostic imaging modality for chest wall disease, but can also guide aspiration or biopsy for pathologic diagnosis

Ultrasonography of chest wall lesion

International Nuclear Information System (INIS)

Park, Cheol Min; Kim, C. H.; Cha, I. H.; Chung, K. B.; Ser, W. H.; Choi, Y. H.

1989-01-01

Thirty-one patients with chest wall diseases were studied with ultrasound to evaluate its role in chest wall lesions. There were eight infectious conditions, 9 benign tumors, 11 malignant lesions and 3 miscellaneous cases. Diffuse chest wall thickening with heterogeneous echogenicity and obliteration of subcutaneous fat layer are findings of acute infection. In cases of tuberculous smpyema necessitates, pleural abnormality extended to the chest wall through intercostal space. Benign tumors were well demarcated, except in 4 cases of lipoma/lipomatosis. Malignant lesions showed irregular soft tissue masses, bone destruction, pleural effusion and subcutaneous invasion. Multiple enlarged lymph nodes were also shown. Ultrasound can demonstrate te internal structure, extent, depth and associated findings such as pleural effusion, bone destruction and peripheral lung involvement. Ultrasound is not only safe, non-invasive and an effective diagnostic imaging modality for chest wall disease, but can also guide aspiration or biopsy for pathologic diagnosis

Domain wall networks on solitons

International Nuclear Information System (INIS)

Sutcliffe, Paul

2003-01-01

Domain wall networks on the surface of a soliton are studied in a simple theory. It consists of two complex scalar fields, in 3+1 dimensions, with a global U(1)xZ n symmetry, where n>2. Solutions are computed numerically in which one of the fields forms a Q ball and the other field forms a network of domain walls localized on the surface of the Q ball. Examples are presented in which the domain walls lie along the edges of a spherical polyhedron, forming junctions at its vertices. It is explained why only a small restricted class of polyhedra can arise as domain wall networks

Regulatory difficulties in a developing country

International Nuclear Information System (INIS)

Jacobs, W.R. Jr.

1978-01-01

The regulatory agency assigned the task of regulating the initial entry into the field of nuclear power generation by a developing country has a very difficult job. Based on the authors' experience during the start-up and initial operation of Ko-Ri Unit I, the first power reactor in the Republic of Korea, observations on regulatory difficulties and recommendations for improved regulatory effectiveness are offered. The problem areas can be loosely grouped into three general categories: (1) Lack of adequate technical knowledge which is the basis for all effective regulation; (2) Difficulties with understanding and utilization of the required regulatory documentation; (3) Failure to establish the proper regulatory environment. Examples are cited from actual experience during the Ko-Ri Unit I start-up to demonstrate the impact that regulatory activities can have on a plant construction and testing programme. The problems encountered are not unique to developing countries but also exist in the United States of America. Recommendations are offered which should be beneficial to either newly formed regulatory agencies or agencies wishing to improve their abilities and effectiveness. These include: (1) Additional training of regulatory inspectors in plant operations; (2) Additional experience gained by participation in regulatory activities in other countries; (3) Increased attention given to regulatory documents, especially plant technical specifications; (4) Establishment of formal lines of communication between the utility and the regulatory agency; (5) Clear definition of regulatory responsibilities to avoid areas of overlapping jurisdiction; (6) Active participation by the regulatory staff very early in the project. It is hoped that these and other recommendations offered will greatly improve regulatory effectiveness and at the same time demonstrate that when the decision is made to 'go nuclear', a strong commitment must be made to develop and support a technically

Regulatory control of nuclear power plants

International Nuclear Information System (INIS)

2002-01-01

The purpose of this book is to support IAEA training courses and workshops in the field of regulatory control of nuclear power plants as well as to support the regulatory bodies of Member States in their own training activities. The target group is the professional staff members of nuclear safety regulatory bodies supervising nuclear power plants and having duties and responsibilities in the following regulatory fields: regulatory framework; regulatory organization; regulatory guidance; licensing and licensing documents; assessment of safety; and regulatory inspection and enforcement. Important topics such as regulatory competence and quality of regulatory work as well as emergency preparedness and public communication are also covered. The book also presents the key issues of nuclear safety such as 'defence-in-depth' and safety culture and explains how these should be taken into account in regulatory work, e.g. during safety assessment and regulatory inspection. The book also reflects how nuclear safety has been developed during the years on the basis of operating experience feedback and results of safety research by giving topical examples. The examples cover development of operating procedures and accident management to cope with complicated incidents and severe accidents to stress the importance of regulatory role in nuclear safety research. The main target group is new staff members of regulatory bodies, but the book also offers good examples for more experienced inspectors to be used as comparison and discussion basis in internal workshops organized by the regulatory bodies for refreshing and continuing training. The book was originally compiled on the basis of presentations provided during the two regulatory control training courses in 1997 and 1998. The textbook was reviewed at the beginning of the years 2000 and 2002 by IAEA staff members and consistency with the latest revisions of safety standards have been ensured. The textbook was completed in the

Relationship between regulatory issues and probabilistic risk assessments

International Nuclear Information System (INIS)

Ilberg, D.; Papazoglou, I.

1985-01-01

The objective of this study was to obtain some perspective on the characteristics and the relative number of regulatory issues that are PRA related, i.e., can be effectively addressed by plant specific PRA studies. It was also aimed at developing approaches to resolution of regulatory issues as part of plant specific PRAs. Several ongoing NRC programs include a number of safety-related issues which are applicable to operating plants. A number of these issues include aspects that strongly interact with items addressed in PRA studies. The resolution of several generic issues using PRA studies has already started. A review of over 335 issues included in three NRC programs was conducted: Generic Issue Program (GI); Systematic Evaluation Program (SEP); and TMI Action Plan (TMI). The review identifid 240 items related to PRA, 120 of which were judged to have significant effect on core damage frequency. It is believed that these items can be effectively treated in a PRA study that includes internal and external events

Application of flexi-wall in noise barriers renewal

Directory of Open Access Journals (Sweden)

B. Daee

2015-12-01

Full Text Available This paper presents an experimental study on structural performance of an innovative noise barrier consisting of poly-block, light polyurethane foam (LPF and polyurea. This wall system (flexi-wall is intended to be employed as a vertical extension to existing noise barriers (sound walls in an accelerated construction method. To aid in the wall design, several mechanical tests were conducted on LPF specimens and two full-scale walls were then fabricated employing the same LPF material. The full-scale walls were subjected to lateral loading in order to establish their lateral resistance. A cyclic fatigue test was also performed on a full-scale flexi-wall in order to evaluate the performance of the wall under a repetitive loading condition. The results of the experiments indicated the suitability of flexi-wall in accelerated construction and confirmed that the structural performance of the wall system under lateral loading is satisfactory for the sound wall application. The experimental results were discussed and a preliminary design procedure for application of flexi-wall in sound wall applications was also developed.

Regulatory Reform and License Termination Planning in Decommissioning

International Nuclear Information System (INIS)

Michael J. Meisner

2000-01-01

Decommissioning of commercial nuclear power plants (NPPs) must be safe and cost-effective and consider the needs of a wide range of stakeholders. The creative tension among these objectives has provided opportunities to reform the way these plants are regulated and managed in decommissioning. Enlightened and visionary leaders from the U.S. Nuclear Regulatory Commission (NRC) and industry are seizing these opportunities to create new paradigms for risk-informed regulation; creative stakeholder involvement; and effective, end-state focused, license termination planning

A unified wall function for compressible turbulence modelling

Science.gov (United States)

Ong, K. C.; Chan, A.

2018-05-01

Turbulence modelling near the wall often requires a high mesh density clustered around the wall and the first cells adjacent to the wall to be placed in the viscous sublayer. As a result, the numerical stability is constrained by the smallest cell size and hence requires high computational overhead. In the present study, a unified wall function is developed which is valid for viscous sublayer, buffer sublayer and inertial sublayer, as well as including effects of compressibility, heat transfer and pressure gradient. The resulting wall function applies to compressible turbulence modelling for both isothermal and adiabatic wall boundary conditions with the non-zero pressure gradient. Two simple wall function algorithms are implemented for practical computation of isothermal and adiabatic wall boundary conditions. The numerical results show that the wall function evaluates the wall shear stress and turbulent quantities of wall adjacent cells at wide range of non-dimensional wall distance and alleviate the number and size of cells required.

Improving nuclear regulatory effectiveness

International Nuclear Information System (INIS)

2001-01-01

Ensuring that nuclear installations are operated and maintained in such a way that their impact on public health and safety is as low as reasonably practicable has been and will continue to be the cornerstone of nuclear regulation. In the past, nuclear incidents provided the main impetus for regulatory change. Today, economic factors, deregulation, technological advancements, government oversight and the general requirements for openness and accountability are leading regulatory bodies to review their effectiveness. In addition, seeking to enhance the present level of nuclear safety by continuously improving the effectiveness of regulatory bodies is seen as one of the ways to strengthen public confidence in the regulatory systems. This report covers the basic concepts underlying nuclear regulatory effectiveness, advances being made and future requirements. The intended audience is primarily nuclear safety regulators, but government authorities, nuclear power plant operators and the general public may also be interested. (author)

The Interaction Features of the Multi-Level Retaining Walls with Soil Mass

Directory of Open Access Journals (Sweden)

Boyko Igor

2017-09-01

Full Text Available The interaction features of multi-level retaining walls with soil base were researched by changing their geometric parameters and locality at the plan. During excavation of deep foundation pits it is important to choose the type of constructions which influences on the horizontal displacements. The distance between the levels of retaining walls should be based on the results of numerical modelling. The objective of this paper is to present a comparison between the data of numerical simulations and the results of the in-situ lateral tests of couple piles. The problems have been solved by using the following soil models: Coulomb-Mohr model; model, which is based on the dilatation theory; elastic-plastic model with variable stiffness parameters.

Engineering the Oryza sativa cell wall with rice NAC transcription factors regulating secondary wall formation

Directory of Open Access Journals (Sweden)

Kouki eYoshida

2013-10-01

Full Text Available Plant tissues that require structural rigidity synthesize a thick, strong secondary cell wall of lignin, cellulose and hemicelluloses in a complicated bridged structure. Master regulators of secondary wall synthesis were identified in dicots, and orthologs of these regulators have been identified in monocots, but regulation of secondary cell wall formation in monocots has not been extensively studied. Here we demonstrate that the rice transcription factors SECONDARY WALL NAC DOMAIN PROTEINs (SWNs can regulate secondary wall formation in rice (Oryza sativa and are potentially useful for engineering the monocot cell wall. The OsSWN1 promoter is highly active in sclerenchymatous cells of the leaf blade and less active in xylem cells. By contrast, the OsSWN2 promoter is highly active in xylem cells and less active in sclerenchymatous cells. OsSWN2 splicing variants encode two proteins; the shorter protein (OsSWN2S has very low transcriptional activation ability, but the longer protein (OsSWN2L and OsSWN1 have strong transcriptional activation ability. In rice, expression of an OsSWN2S chimeric repressor, driven by the OsSWN2 promoter, resulted in stunted growth and para-wilting (leaf rolling and browning under normal water conditions due to impaired vascular vessels. The same OsSWN2S chimeric repressor, driven by the OsSWN1 promoter, caused a reduction of cell wall thickening in sclerenchymatous cells, a drooping leaf phenotype, reduced lignin and xylose contents and increased digestibility as forage. These data suggest that OsSWNs regulate secondary wall formation in rice and manipulation of OsSWNs may enable improvements in monocotyledonous crops for forage or biofuel applications.

Hydrodynamics of ultra-relativistic bubble walls

Energy Technology Data Exchange (ETDEWEB)

Leitao, Leonardo, E-mail: lleitao@mdp.edu.ar; Mégevand, Ariel, E-mail: megevand@mdp.edu.ar

2016-04-15

In cosmological first-order phase transitions, gravitational waves are generated by the collisions of bubble walls and by the bulk motions caused in the fluid. A sizeable signal may result from fast-moving walls. In this work we study the hydrodynamics associated to the fastest propagation modes, namely, ultra-relativistic detonations and runaway solutions. We compute the energy injected by the phase transition into the fluid and the energy which accumulates in the bubble walls. We provide analytic approximations and fits as functions of the net force acting on the wall, which can be readily evaluated for specific models. We also study the back-reaction of hydrodynamics on the wall motion, and we discuss the extrapolation of the friction force away from the ultra-relativistic limit. We use these results to estimate the gravitational wave signal from detonations and runaway walls.

Performance Objective for Tank Farm Closure Risk Assessments

International Nuclear Information System (INIS)

MANN, F.M.; KNEPP, A.J.; BADDEN, J.

2003-01-01

To be meaningful, results from a numeric risk assessment of the consequences of an action must be compared against the standards for such an action. That is, before one disposes of waste or closes a facility with waste, one must show that the disposal or closure action protects the public health and safety and the environment. These standards are called performance objectives. Regulations requiring performing performance assessments, (whether federal ones like the Department of Energy [DOE] Order 435.1, Radioactive Waste Management and its implementing guides or Washington State ones like the regulations implementing the Washington Administrative Code [WAC] 173-340 ''Model Toxics Control Act - Cleanup''), usually require that the determination of performance objectives be one of the first steps performed. These performance objectives not only set comparison level for the numeric results, but also define the media, pathways, exposure scenarios (receptors), spatial locations, and times that the performance assessment must consider. Thus, a performance objective consists of a compliance level, place(s) of compliance, and time(s) of compliance. Performance objectives are not the levels that a regulatory agency will enforce in a permit or authorization. Those levels, often called enforcement levels, will be set in the permit or authorization. Rather, performance objectives are those levels against which the results of the numeric simulation will be compared to judge the success of the proposed cleanup or disposal actions. Additional comparison levels may be requested for information purposes, but are not officially part of the decision on the adequacy of the proposed action. To emphasize that the performance objectives discussed in this document are not regulatory performance objectives, the three components of the performance objective will be renamed in this document as assessment standard, point(s) of assessment, and time(s) of assessment. However, whenever

75 FR 27606 - Self-Regulatory Organizations; Financial Industry Regulatory Authority, Inc.; Notice of Filing...

Science.gov (United States)

2010-05-17

...-Regulatory Organizations; Financial Industry Regulatory Authority, Inc.; Notice of Filing and Immediate...\\ and Rule 19b-4 thereunder,\\2\\ notice is hereby given that on April 27, 2010, the Financial Industry... restated following the formation of FINRA through the consolidation of NASD and the member regulatory...

Regulatory audit to the Argentine teletherapy units

International Nuclear Information System (INIS)

Kay, J.M.

1995-01-01

As a consequence of an erroneous calibration of the ionization chamber dosimeter of a new licensed 6 Mev electron lineal accelerator that caused accidental overexposures in the first patients under treatment, the Regulatory Board decided to perform an audit to every teletherapy unit (accelerator and telegammatherapy units) in Argentina. The audit was carried out at the en of 1994 in 27 accelerators and 107 telegammatherapy units. The objectives of the audit were the control of the mechanical and optical aspects of the each accelerator and telegammatherapy unit and the control of the calibration of their radiation beams. The last action was undertaken to detect as soon as possible, any eventual accidental overexposure or underexposure of patients under treatment. The audit was conducted by the author and performed for a team of 22 inspectors who worked in groups of 2 to 3 people and completed the inspection of the teletherapy units of the whole country in 3 months. As a result of the audit, the Regulatory Board had in a short period a clear panorama of the performance of each teletherapy unit of the country and also confirmed that no accidental situation had happened. The audit revealed the necessity of imposing urgent regulatory requirements not related to the calibration of the radiation beam in 5% of the cases, as well as non-urgent requirements of different importance in approximately other 60% of the cases. (author)

Nuclear Regulatory legislation

International Nuclear Information System (INIS)

1984-06-01

This compilation of statutes and material pertaining to nuclear regulatory legislation through the 97th Congress, 2nd Session, has been prepared by the Office of the Executive Legal Director, U.S. Nuclear Regulatory Commission, with the assistance of staff, for use as an internal resource document

Molecular regulation of plant cell wall extensibility

Science.gov (United States)

Cosgrove, D. J.

1998-01-01

Gravity responses in plants often involve spatial and temporal changes in cell growth, which is regulated primarily by controlling the ability of the cell wall to extend. The wall is thought to be a cellulose-hemicellulose network embedded in a hydrated matrix of complex polysaccharides and a small amount of structural protein. The wall extends by a form of polymer creep, which is mediated by expansins, a novel group of wall-loosening proteins. Expansins were discovered during a molecular dissection of the "acid growth" behavior of cell walls. Expansin alters the rheology of plant walls in profound ways, yet its molecular mechanism of action is still uncertain. It lacks detectable hydrolytic activity against the major components of the wall, but it is able to disrupt noncovalent adhesion between wall polysaccharides. The discovery of a second family of expansins (beta-expansins) sheds light on the biological role of a major group of pollen allergens and implies that expansins have evolved for diverse developmental functions. Finally, the contribution of other processes to wall extensibility is briefly summarized.

A Review of Double-Walled and Triple-Walled Carbon Nanotube Synthesis and Applications

Directory of Open Access Journals (Sweden)

Kazunori Fujisawa

2016-04-01

Full Text Available Double- and triple-walled carbon nanotubes (DWNTs and TWNTs consist of coaxially-nested two and three single-walled carbon nanotubes (SWNTs. They act as the geometrical bridge between SWNTs and multi-walled carbon nanotubes (MWNTs, providing an ideal model for studying the coupling interactions between different shells in MWNTs. Within this context, this article comprehensively reviews various synthetic routes of DWNTs’ and TWNTs’ production, such as arc discharge, catalytic chemical vapor deposition and thermal annealing of pea pods (i.e., SWNTs encapsulating fullerenes. Their structural features, as well as promising applications and future perspectives are also discussed.

75 FR 53998 - Self-Regulatory Organizations; Financial Industry Regulatory Authority, Inc.; Notice of Filing...

Science.gov (United States)

2010-09-02

... characteristics and risks of security futures. \\6\\ 15 U.S.C. 78o-3(b)(6). B. Self-Regulatory Organization's...-Regulatory Organizations; Financial Industry Regulatory Authority, Inc.; Notice of Filing and Immediate Effectiveness of Proposed Rule Change To Amend the Security Futures Risk Disclosure Statement August 27, 2010...

Reactor pressure vessel failure probability following through-wall cracks due to pressurized thermal shock events

International Nuclear Information System (INIS)

Simonen, F.A.; Garnich, M.R.; Simonen, E.P.; Bian, S.H.; Nomura, K.K.; Anderson, W.E.; Pedersen, L.T.

1986-04-01

A fracture mechanics model was developed at the Pacific Northwest Laboratory (PNL) to predict the behavior of a reactor pressure vessel following a through-wall crack that occurs during a pressurized thermal shock (PTS) event. This study, which contributed to a US Nuclear Regulatory Commission (NRC) program to study PTS risk, was coordinated with the Integrated Pressurized Thermal Shock (IPTS) Program at Oak Ridge National Laboratory (ORNL). The PNL fracture mechanics model uses the critical transients and probabilities of through-wall cracks from the IPTS Program. The PNL model predicts the arrest, reinitiation, and direction of crack growth for a postulated through-wall crack and thereby predicts the mode of vessel failure. A Monte-Carlo type of computer code was written to predict the probabilities of the alternative failure modes. This code treats the fracture mechanics properties of the various welds and plates of a vessel as random variables. Plant-specific calculations were performed for the Oconee-1, Calvert Cliffs-1, and H.B. Robinson-2 reactor pressure vessels for the conditions of postulated transients. The model predicted that 50% or more of the through-wall axial cracks will turn to follow a circumferential weld. The predicted failure mode is a complete circumferential fracture of the vessel, which results in a potential vertically directed missile consisting of the upper head assembly. Missile arrest calculations for the three nuclear plants predict that such vertical missiles, as well as all potential horizontally directed fragmentation type missiles, will be confined to the vessel enclosre cavity. The PNL failure mode model is recommended for use in future evaluations of other plants, to determine the failure modes that are most probable for postulated PTS events

The practicality of defensive ice walls: How would the great ice wall in Game of Thrones hold up?

Science.gov (United States)

Truffer, M.

2017-12-01

The Game of Thrones great ice wall is a colossal feature stretching several hundred miles and over 200 m high. Its purpose is to defend the realm from the wildlings. It is generally pictured as a near vertical wall. An ice wall of these proportions poses interesting challenges, mainly because ice acts as a non-linear shear-thinning fluid. A 200 m high vertical wall would create a large effective stress near its base of almost 1.8 MPa. Typical stresses responsible for ice flow in glaciers and ice sheets are more than a magnitude lower (0.1 MPa). Extrapolating a commonly used flow law for temperate ice to such high stresses would lead to strain rates at the bottom of the wall in excess of 1/day, meaning the wall would rapidly collapse and spread laterally under its own weight. To keep the wall stable, it would help to cool it significantly, as the flow of ice is also very temperature dependent. Cooling to a chilly -40 C would reduce strain rates by two orders of magnitude, but this still leads to significant slumping of the wall within just a few weeks. A time-dependent similarity solution for simplified ice flow equations that describe the evolving shape of the ice wall was provided by Halfar (1981), and demonstrates the rapid decay of the wall. A simple estimate can be derived by assuming that ice is a perfectly plastic fluid, able to maintain a basal shear stress of about 0.1 MPa. A stable ice wall would then spread laterally to about 4 km width. The resulting slope would only be steep at the very margin and the ice wall would loose much of its defensive capabilities. I conclude that the ice wall as proposed would not be a practicable defense under typical Earth conditions, and special magical powers would be necessary to maintain its shape, even for just a few days.

The cell wall of Fusarium oxysporum

NARCIS (Netherlands)

Schoffelmeer, EAM; Klis, FM; Sietsma, JH; Cornelissen, BJC

1999-01-01

Sugar analysis of isolated cell walls from three formae speciales of Fusarium oxysporum showed that they contained not only glucose and (N-acetyl)-glucosamine, but also mannose, galactose, and uronic acids, presumably originating from cell wall glycoproteins. Cell wall glycoproteins accounted for

Characterization of the Sclerotinia sclerotiorum cell wall proteome.

Science.gov (United States)

Liu, Longzhou; Free, Stephen J

2016-08-01

We used a proteomic analysis to identify cell wall proteins released from Sclerotinia sclerotiorum hyphal and sclerotial cell walls via a trifluoromethanesulfonic acid (TFMS) digestion. Cell walls from hyphae grown in Vogel's glucose medium (a synthetic medium lacking plant materials), from hyphae grown in potato dextrose broth and from sclerotia produced on potato dextrose agar were used in the analysis. Under the conditions used, TFMS digests the glycosidic linkages in the cell walls to release intact cell wall proteins. The analysis identified 24 glycosylphosphatidylinositol (GPI)-anchored cell wall proteins and 30 non-GPI-anchored cell wall proteins. We found that the cell walls contained an array of cell wall biosynthetic enzymes similar to those found in the cell walls of other fungi. When comparing the proteins in hyphal cell walls grown in potato dextrose broth with those in hyphal cell walls grown in the absence of plant material, it was found that a core group of cell wall biosynthetic proteins and some proteins associated with pathogenicity (secreted cellulases, pectin lyases, glucosidases and proteases) were expressed in both types of hyphae. The hyphae grown in potato dextrose broth contained a number of additional proteins (laccases, oxalate decarboxylase, peroxidase, polysaccharide deacetylase and several proteins unique to Sclerotinia and Botrytis) that might facilitate growth on a plant host. A comparison of the proteins in the sclerotial cell wall with the proteins in the hyphal cell wall demonstrated that sclerotia formation is not marked by a major shift in the composition of cell wall protein. We found that the S. sclerotiorum cell walls contained 11 cell wall proteins that were encoded only in Sclerotinia and Botrytis genomes. © 2015 The Authors. Molecular Plant Pathology published by British Society for Plant Pathology and John Wiley & Sons Ltd.

Hydrodynamics of ultra-relativistic bubble walls

Directory of Open Access Journals (Sweden)

Leonardo Leitao

2016-04-01

Full Text Available In cosmological first-order phase transitions, gravitational waves are generated by the collisions of bubble walls and by the bulk motions caused in the fluid. A sizeable signal may result from fast-moving walls. In this work we study the hydrodynamics associated to the fastest propagation modes, namely, ultra-relativistic detonations and runaway solutions. We compute the energy injected by the phase transition into the fluid and the energy which accumulates in the bubble walls. We provide analytic approximations and fits as functions of the net force acting on the wall, which can be readily evaluated for specific models. We also study the back-reaction of hydrodynamics on the wall motion, and we discuss the extrapolation of the friction force away from the ultra-relativistic limit. We use these results to estimate the gravitational wave signal from detonations and runaway walls.

NRC regulatory agenda

International Nuclear Information System (INIS)

1990-01-01

The NRC Regulatory Agenda is a compilation of all rules on which the NRC has proposed or is considering action and all petitions for rulemaking which have been received by the Commission and are pending disposition by the Commission. The Regulatory Agenda is updated and issued each quarter

Nonsingular walls in plane cholesteric layers

International Nuclear Information System (INIS)

Belyakov, V A; Osipov, M A; Stewart, I W

2006-01-01

The structure of a straight interface (wall) between regions with differing values of the pitch in planar cholesteric layers with finite strength of the surface anchoring is investigated theoretically. It is found that the shape and strength of the anchoring potential influences essentially the structure of the wall and a motionless wall between thermodynamically stable regions without a singularity in the director distribution in the layer can exist for sufficiently weak anchoring only. More specifically, for the existence of such a wall the dimensionless parameter S d = K 22 /Wd (where W is the depth of the anchoring potential, K 22 is the elastic twist modulus and d is the layer thickness) should exceed its critical value, which is dependent on the shape of the anchoring potential. General equations describing the director distribution in the wall are presented. Detailed analysis of these equations is carried out for the case of infinitely strong anchoring at one surface and finite anchoring strength at the second layer surface. It is shown that the wall width L is directly dependent upon the shape and strength of the anchoring potential and that its estimate ranges from d to (dL p ) 1/2 (where L p = K 22 /W is the penetration length), corresponding to different anchoring strengths and shape potentials. The dependence of the director distribution in the wall upon all three Frank elastic moduli is analytically found for some specific limiting cases of the model anchoring potentials. Motion of the wall is briefly investigated and the corresponding calculations performed under the assumption that the shape of a moving wall is the same as a motionless one. It is noted that experimental investigation of the walls in planar cholesteric layers can be used for the determination of the actual shape of surface anchoring potentials

Immersion Refractometry of Isolated Bacterial Cell Walls

Science.gov (United States)

Marquis, Robert E.

1973-01-01

Immersion-refractometric and light-scattering measurements were adapted to determinations of average refractive indices and physical compactness of isolated bacterial cell walls. The structures were immersed in solutions containing various concentrations of polymer molecules that cannot penetrate into wall pores, and then an estimate was made of the polymer concentration or the refractive index of the polymer solution in which light scattering was reduced to zero. Because each wall preparation was heterogeneous, the refractive index of the medium for zero light scattering had to be estimated by extrapolation. Refractive indices for walls suspended in bovine serum albumin solutions ranged from 1.348 for walls of the rod form of Arthrobacter crystallopoietes to 1.382 for walls of the teichoic acid deficient, 52A5 strain of Staphylococcus aureus. These indices were used to calculate approximate values for solids content per milliliter, and the calculated values agreed closely with those estimated from a knowledge of dextran-impermeable volumes per gram, dry weight, of the walls. When large molecules such as dextrans or serum albumin were used for immersion refractometry, the refractive indices obtained were for entire walls, including both wall polymers and wall water. When smaller molecules that can penetrate wall pores to various extents were used with Micrococcus lysodeikticus walls, the average, apparent refractive index of the structures increased as the molecular size of probing molecules was decreased. It was possible to obtain an estimate of 1.45 to 1.46 for the refractive index of wall polymers, predominantly peptidoglycans in this case, by extrapolating the curve for refractive index versus molecular radius to a value of 0.2 nm, the approximate radius of a water molecule. This relatively low value for polymer refractive index was interpreted as evidence in favor of the amorphous, elastic model of peptidoglycan structure and against the crystalline, rigid

Numerical investigation into the failure of a micropile retaining wall

OpenAIRE

Prat Catalán, Pere

2017-01-01

The paper presents a numerical investigation on the failure of a micropile wall that collapsed while excavating the adjacent ground. The main objectives are: to estimate the strength parameters of the ground; to perform a sensitivity analysis on the back slope height and to obtain the shape and position of the failure surface. Because of uncertainty of the original strength parameters, a simplified backanalysis using a range of cohesion/friction pairs has been used to estimate the most realis...

Wall motion abnormality of myocardial infarction

International Nuclear Information System (INIS)

Hayashi, Senji; Tsuda, Takashi; Ojima, Kenji

1984-01-01

By use of the gated blood pool scan, we divided the left ventricular LAO 45 image into 8 sections with the center of the volume as the basal point, and devised a method of quantitative evaluation of the regional wall motion from 2 aspects: 1) wall movement and 2) phase abnormality. To evaluate the wall movement, we obtained the following indeces from count curves of each section: 1) EF1=(end-diastolic count-end-systolic count)/ end-diastolic count, 2) EF2=(maximum count-minimum count)/maximum count, and 3) the difference of the two (EF2-EF1). As indeces of the phase abnormality, the mean value of phases of the pixels (phase characteristics) and the standard deviation (variation) of each section were calculated. Furthermore, the phase delay of each section was calculated as the difference from the earliest phase value of the 8 sections. Control values and standard deviation were obtained from 8 healthy controls. By this method, we analyzed 20 patients with old myocardial infarction. And following results were obtained: 1. Applying this method, we could evaluate the regional wall motion of the left ventricle more precisely, and we considered it would be useful clinically. 2. The abnormal regional wall motion of old myocardial infarction were classified into 4 typical forms as follows: 1) the wall movement decreased extremely. 2) the wall movement decreased, but no phase delay recognized. 3) the wall movement did not decrease, but phase delay was recognized. 4) the wall movement decreased, and phase delay was recognized. (author)