WorldWideScience

Sample records for volumetric expansion coefficient

  1. Correlation dependence of the volumetric thermal expansion coefficient of metallic aluminum on its heat capacity

    Science.gov (United States)

    Bodryakov, V. Yu.; Bykov, A. A.

    2016-05-01

    The correlation between the volumetric thermal expansion coefficient β( T) and the heat capacity C( T) of aluminum is considered in detail. It is shown that a clear correlation is observed in a significantly wider temperature range, up to the melting temperature of the metal, along with the low-temperature range where it is linear. The significant deviation of dependence β( C) from the low-temperature linear behavior is observed up to the point where the heat capacity achieves the classical Dulong-Petit limit of 3 R ( R is the universal gas constant).

  2. A reduced volumetric expansion factor plot

    Science.gov (United States)

    Hendricks, R. C.

    1979-01-01

    A reduced volumetric expansion factor plot has been constructed for simple fluids which is suitable for engineering computations in heat transfer. Volumetric expansion factors have been found useful in correlating heat transfer data over a wide range of operating conditions including liquids, gases and the near critical region.

  3. Thermal expansion coefficient of binary semiconductors

    Energy Technology Data Exchange (ETDEWEB)

    Kumar, V.; Sastry, B.S.R. [Indian School of Mines, Dhanbad (India). Dept. of Electronics and Instrumentation

    2001-07-01

    The linear thermal expansion coefficient of tetrahedrally coordinated A{sup II}B{sup VI} and A{sup III}B{sup V} semiconductors has been calculated using plasmon energy data. A simple relation between the bond length and plasmon energy has been derived. The calculated values of thermal expansion coefficient and bond length have been compared with the experimental values and the values reported by different workers. An excellent experiment has been obtained between them. (orig.)

  4. Thermal Expansion Coefficients of Thin Crystal Films

    Institute of Scientific and Technical Information of China (English)

    2005-01-01

    The formulas for atomic displacements and Hamiltonian of a thin crystal film in phonon occupation number representation are obtained with the aid of Green's function theory. On the basis of these results, the formulas for thermal expansion coefficients of the thin crystal film are derived with the perturbation theory, and the numerical calculations are carried out. The results show that the thinner films have larger thermal expansion coefficients.

  5. Recursive Construction of Operator Product Expansion Coefficients

    Science.gov (United States)

    Holland, Jan; Hollands, Stefan

    2015-06-01

    We derive a novel formula for the derivative of operator product expansion (OPE) coefficients with respect to a coupling constant. The formula involves just the OPE coefficients themselves but no further input, and is in this sense self-consistent. Furthermore, unlike other formal identities of this general nature in quantum field theory (such as the formal expression for the Lagrangian perturbation of a correlation function), our formula requires no further UV-renormalization, i.e., it is completely well-defined from the start. This feature is a result of a cancelation of UV- and IR-divergences between various terms in our identity. Our proof, and an analysis of the features of the identity, is given for the example of massive, Euclidean theory in 4 dimensional Euclidean space. It relies on the renormalization group flow equation method and is valid to arbitrary, but finite orders in perturbation theory. The final formula, however, makes neither explicit reference to the renormalization group flow, nor to perturbation theory, and we conjecture that it also holds non-perturbatively. Our identity can be applied constructively because it gives a novel recursive algorithm for the computation of OPE coefficients to arbitrary (finite) perturbation order in terms of the zeroth order coefficients corresponding to the underlying free field theory, which in turn are trivial to obtain. We briefly illustrate the relation of this method to more standard methods for computing the OPE in some simple examples.

  6. Recursive construction of operator product expansion coefficients

    CERN Document Server

    Holland, J

    2014-01-01

    We derive a novel formula for the derivative of operator product expansion (OPE) coefficients with respect to a coupling constant. The formula only involves the OPE coefficients themselves, and no further input, and is in this sense self-consistent. Furthermore, unlike other formal identities of this general nature in quantum field theory (such as the formal expression for the Lagrangian perturbation of a correlation function), our formula is completely well-defined from the start, i.e. requires no further UV-renormalization. This feature is a result of a cancelation of UV-divergences between various terms in our identity. Our proof, and an analysis of the features, of our identity is given for the example of massive, Euclidean $\\varphi^4$ theory in 4 dimensional Euclidean space, and relies heavily on the framework of the renormalization group flow equations. It is valid to arbitrary, but finite orders in perturbation theory. The final formula, however, makes no explicit reference to the renormalization group...

  7. Virial expansion coefficients in the harmonic approximation

    DEFF Research Database (Denmark)

    R. Armstrong, J.; Zinner, Nikolaj Thomas; V. Fedorov, D.

    2012-01-01

    The virial expansion method is applied within a harmonic approximation to an interacting N-body system of identical fermions. We compute the canonical partition functions for two and three particles to get the two lowest orders in the expansion. The energy spectrum is carefully interpolated...

  8. Expansion Coefficient on Oxides and Oxide Ceramics.

    Science.gov (United States)

    1986-05-01

    Ferroelectrics )," Ph.D. thesis submitted to the Indian Institute of Science, Bangalore- 12, (1969). 29. B. Alefeld. "The Change of Lattice Parameters of...Kamenetskii. "Anomalous Thermal Expansion of ZrO2 and HfO2 Over the Range 20-1200 0 C," Soy. Phy.-Cryst., 14 (1970) pp. 696-99. 89. A. K. Sreedhar. "Thermal...D. Gac. "Axial and Linear Thermal Expansion of ZrO 2 and HfO2 ," Am. Ceram. Soc. RuZl. 60(4) (1981), pp. 504-506. 167. R. Ruh, G. W. Hollenberg, E

  9. VOLUMETRIC MASS TRANSFER COEFFICIENT BETWEEN SLAG AND METAL IN COMBINED BLOWING CONVERTER

    Institute of Scientific and Technical Information of China (English)

    Z.H. Wu; Z.S. Zou; W. Wu

    2005-01-01

    The effects of operation parameters of combined blowing converter on the volumetric mass transfer coefficient between slag and steel are studied with a cold model with water simulating steel, oil simulating slag and benzoic acid as the transferred substance between water and oil. The results show that, with lance level of 2.Im and the top blowing rate of 25000Nm3/h, the volumetric mass transfer coefficient changes most significantly when the bottom blowing rate ranges from 384 to 540Nm3/h. The volumetric mass transfer coefficient reaches its maximum when the lance level is 2. lm, the top blowing rates is 30000Nm3/h, and the bottom blowing rate is 384Nrr3/h with tuyeres located symmetrically at 0.66D of the converter bottom.

  10. Seal assembly for materials with different coefficients of thermal expansion

    Science.gov (United States)

    Minford, Eric

    2009-09-01

    Seal assembly comprising (a) two or more seal elements, each element having having a coefficient of thermal expansion; and (b) a clamping element having a first segment, a second segment, and a connecting segment between and attached to the first and second segments, wherein the two or more seal elements are disposed between the first and second segments of the clamping element. The connecting segment has a central portion extending between the first segment of the clamping element and the second segment of the clamping element, and the connecting segment is made of a material having a coefficient of thermal expansion. The coefficient of thermal expansion of the material of the connecting segment is intermediate the largest and smallest of the coefficients of thermal expansion of the materials of the two or more seal elements.

  11. Empirical correlation of volumetric mass transfer coefficient for a rectangular internal-loop airlift bioreactor

    Science.gov (United States)

    An empirical correlation of volumetric mass transfer coefficient was developed for a pilot scale internal-loop rectangular airlift bioreactor that was designed for biotechnology. The empirical correlation combines classic turbulence theory, Kolmogorov’s isotropic turbulence theory with Higbie’s pen...

  12. An Autologous Muscle Tissue Expansion Approach for the Treatment of Volumetric Muscle Loss

    Science.gov (United States)

    2015-07-01

    ORIGINAL RESEARCH ARTICLE Open Access An Autologous Muscle Tissue Expansion Approach for the Treatment of Volumetric Muscle Loss Catherine L. Ward...regeneration. But they require ample donor muscle tissue and therefore may be limited in their application for large clinical VML. Here, we tested the...autologous minced grafts for the regeneration of muscle tissue after VML, but indicate the need to identify optimal carrier materials for expansion

  13. Determination of effective thermal expansion coefficients of unidirectional fibrous nanocomposites

    Science.gov (United States)

    Dai, Ming; Schiavone, Peter; Gao, Cun-Fa

    2016-10-01

    We present an efficient numerical scheme (based on complex variable techniques) to calculate the effective thermal expansion coefficients of a composite containing unidirectional periodic fibers. Moreover, the mechanical behavior of the fibers incorporates interface effects allowing the ensuing analytical model of the composite to accommodate deformations at the nanoscale. The resulting `nanocomposite' is subjected to a uniform temperature variation which leads to periodic deformations within the plane perpendicular to the fibers and uniform deformations along the direction of the fibers. These deformation fields are determined by analyzing a representative unit cell of the composite subsequently leading to the corresponding effective thermal expansion coefficients. Numerical results are illustrated via several physical examples. We find that the influence of interface effects on the effective thermal expansion coefficients (in particular that corresponding to the transverse direction in the plane perpendicular to the fibers) decays rapidly as the fibers become harder. In addition, by comparing the results obtained here with those from effective medium theories, we show that the latter may induce significant errors in the determination of the effective transverse thermal expansion coefficient when the fibers are much softer than the matrix and the fiber volume fraction is relatively high.

  14. Generalized multitime expansions for equations with slowly varying coefficients

    Directory of Open Access Journals (Sweden)

    L. E. Levine

    1984-01-01

    Full Text Available The successive terms in a uniformly valid multitime expansion of the solutions of constant coefficient differential equations containing a small parameter ϵ may be obtained without resorting to secularity conditions if the time scales ti=ϵit(i=0,1,… are used. Similar results have been achieved in some cases for equations with variable coefficients by using nonlinear time scales generated from the equations themselves. This paper extends the latter approach to the general second order ordinary differential equation with slowly varying coefficients and examines the restrictions imposed by the method.

  15. Measurement of thermal expansion coefficient of nonuniform temperature specimen

    Institute of Scientific and Technical Information of China (English)

    Jingmin Dai; Chunsuo Kin; Xiaowa He

    2008-01-01

    A new technique is developed to measure the longitudinal thermal expansion coefficient of C/C composite material at high temperature. The measuring principle and components of the apparatus are described in detail. The calculation method is derived from the temperature dependence of the thermal expansion coefficient. The apparatus mainly consists of a high temperature environmental chamber, a power circuit of heating, two high-speed pyrometers, and a laser scanning system. A long solid specimen is resistively heated to a steady high-temperature state by a steady electrical current. The temperature profile of the specimen surface is not uniform because of the thermal conduction and radiation. The temperature profile and the total expansion are measured with a high-speed scanning pyrometer and a laser slit scanning measuring system, respectively. The thermal expansion coefficient in a wide temperature range (1000 - 3800 K) of the specimen can therefore be obtained. The perfect consistency between the present and previous results justifies the validity of this technique.

  16. The Coefficients of Thermal Expansion of Boron Arsenide (B12As2) Between 25 C and 850 C

    Energy Technology Data Exchange (ETDEWEB)

    Whiteley, Clinton E. [Kansas State University; Kirkham, Melanie J [ORNL; Edgar, J H [Kansas State University

    2013-01-01

    The semiconductor boron arsenide has a high 10B density, a wide bandgap, and a high melting temperature, all of which make it an interesting candidate for high-temperature electronic devices and radiation detectors. The present investigation was undertaken to determine the coefficients of thermal expansion for boron arsenide. B12As2 powder was synthesized from boron and arsenic heated in a sealed quartz ampoule at 1100 C for 72 hrs with excess boron. Using high temperature X-ray diffraction (HTXRD) between 25 C and 850 C, the average lattice coefficients of thermal expansion were measured perpendicular and parallel to the <111> axis in the rhombohedral setting (equivalent to the a and c axes in the hexagonal setting): 4.9x10-6 K-1 and 5.3x10-6 K-1, respectively. The average unit cell volumetric coefficient of thermal expansion was determined to be 1.5x10-5 K-1.

  17. Measurement of Thermal Expansion Coefficients with Holographic Technique

    Institute of Scientific and Technical Information of China (English)

    ZhifengZhang

    1995-01-01

    A simplified mathematical model was created for measurement of thermal expansion coefficients of thin sheet materials with holographic technique.Experimental set-ups corresponding to the mathematical model were designed and built for both tests above room temperature and at low temperatures.A fringe control technique was introduced for low temperature measurements to compensate rigid body movement,THin sheet specimens of silicon and aluminum alloy(7075) were tested with the developed technique.The tested results are in good agreement with reported data and thus verify the validity of the developed technique.The Thermal expansion coefficients of the tested materials ranged from 2.5×10-60C-1 to 23.6×10-6oC-1.

  18. Quantum elasticity of graphene: Thermal expansion coefficient and specific heat

    Science.gov (United States)

    Burmistrov, I. S.; Gornyi, I. V.; Kachorovskii, V. Yu.; Katsnelson, M. I.; Mirlin, A. D.

    2016-11-01

    We explore thermodynamics of a quantum membrane, with a particular application to suspended graphene membrane and with a particular focus on the thermal expansion coefficient. We show that an interplay between quantum and classical anharmonicity-controlled fluctuations leads to unusual elastic properties of the membrane. The effect of quantum fluctuations is governed by the dimensionless coupling constant, g0≪1 , which vanishes in the classical limit (ℏ →0 ) and is equal to ≃0.05 for graphene. We demonstrate that the thermal expansion coefficient αT of the membrane is negative and remains nearly constant down to extremely low temperatures, T0∝exp(-2 /g0) . We also find that αT diverges in the classical limit: αT∝-ln(1 /g0) for g0→0 . For graphene parameters, we estimate the value of the thermal expansion coefficient as αT≃-0.23 eV-1 , which applies below the temperature Tuv˜g0ϰ0˜500 K (where ϰ0˜1 eV is the bending rigidity) down to T0˜10-14 K. For T specific heat of the membrane and investigate the behavior of the Grüneisen parameter.

  19. 1-D diffusion based solidification model with volumetric expansion and shrinkage effect: A semi-analytical approach

    Science.gov (United States)

    Monde, Aniket D.; Chakraborty, Prodyut R.

    2017-10-01

    Volumetric expansion and shrinkage due to different densities of solid and liquid phases are common phenomena during solidification process. Simple analytical models addressing effect of volumetric expansion/shrinkage during solidification are rarely found. The few existing 1-D solidification models are valid only for semi-infinite domain with limitations of their application for finite domain size. The focus of the present work is to develop a 1-D semi-analytical solidification model addressing effects of volumetric expansion/shrinkage in a finite domain. The proposed semi-analytical scheme involves finding simultaneous solution of transient 1-D heat diffusion equations at solid and liquid domain coupled at the interface by Stefan condition. The change of the total domain length during solidification due to volumetric expansion/shrinkage is addressed by using mass conservation. For validation of the proposed model, solidification of water in a finite domain is studied without considering volumetric expansion/shrinkage effect and results are compared with those obtained from existing enthalpy updating based numerical model. After validation, case studies pertaining to volumetric expansion and shrinkage are performed considering solidification of water and paraffin respectively and physically consistent results are obtained. The study is relevant for understanding unidirectional crystal growth under the effect of controlled boundary condition.

  20. A Noncontact Measurement Technique for the Density and Thermal Expansion Coefficient of Solid and Liquid Materials

    Science.gov (United States)

    Chung, Sang K.; Thiessen, David B.; Rhim, Won-Kyu

    1996-01-01

    A noncontact measurement technique for the density and the thermal expansion refractory materials in their molten as well as solid phases is presented. This technique is based on the video image processing of a levitated sample. Experiments were performed using the high-temperature electrostatic levitator (HTESL) at the Jet Propulsion Laboratory in which 2-3 mm diameter samples can be levitated, melted, and radiatively cooled in a vacuum. Due to the axisymmetric nature of the molten samples when levitated in the HTESL, a rather simple digital image analysis can be employed to accurately measure the volumetric change as a function of temperature. Density and the thermal expansion coefficient measurements were made on a pure nickel sample to test the accuracy of the technique in the temperature range of 1045-1565 C. The result for the liquid phase density can be expressed by p = 8.848 + (6.730 x 10(exp -4)) x T (degC) g/cu cm within 0.8% accuracy, and the corresponding thermal expansion coefficient can be expressed by Beta=(9.419 x 10(exp -5)) - (7.165 x 10(exp -9) x T (degC)/K within 0.2% accuracy.

  1. Coefficient of thermal expansion of stressed thin films

    Institute of Scientific and Technical Information of China (English)

    WANG Zheng-dao; JIANG Shao-qing

    2006-01-01

    A new technique was proposed to determine the coefficient of thermal expansion (CTE) of thin films at low temperature. Different pre-stress could be applied and the elastic modulus of materials at different temperatures was measured with CTE simultaneously to eliminate the influence of mechanical deformation caused by the pre-stress. By using this technique,the CTEs of polyimide/silica nanocomposite films with different silica doping levels were experimentally studied at temperature from 77 K to 287 K,and some characteristics related to this new technique were discussed.

  2. Modulus of Elasticity and Thermal Expansion Coefficient of ITO Film

    Energy Technology Data Exchange (ETDEWEB)

    Carter, Austin D. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Elhadj, S. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

    2016-06-24

    The purpose of this experiment was to determine the modulus of elasticity (E) and thermal expansion coefficient (α) of RF sputtered Indium Tin Oxide (ITO) as a function of temperature (T), and to collect ITO film stress data. In order to accomplish that goal, the Toho FLX-2320-S thin film stress measurement machine was used to collect both single stress and stress-temperature data for ITO coated fused silica and sapphire substrates. The stress measurement function of the FLX-2320-S cannot be used to calculate the elastic modulus of the film because the Stoney formula incorporates the elastic modulus of the substrate, rather than of the film itself.

  3. Effect of MgO Additive on Volumetric Expansion of Self-Degradable Cements

    Energy Technology Data Exchange (ETDEWEB)

    Sugama T.; Warren, J.; Butcher, T.

    2011-09-30

    We identified hard-burned magnesium oxide (MgO) as a suitable expansive additive for improving the plugging performance of self-degradable, temporary sodium silicate-activated slag/Class C fly ash (SSASC) blend cement sealers into rock fractures in Enhanced Geothermal Systems (EGSs). MgO extended the volumetric expansion of sealers during their exposure to a hydrothermal environment at 200 C under pressures, ranging from 300 to 1500 psi. A great expansion ratc of 19.3% was observed by adding 3.0 wt% MgO under 300 psi pressure, thus promising to plug thoroughly inner fracture. When the pressure was increased from 300 psi to 1500 psi, the expansion rate of cement markedly reduced, corresponding to the formaLion of crack-free specimens and the improvement of compressive strength. However, with 3.0 wt% MgO, the specimens still engendered the generation of numerous visual cracks, although they were prepared under a high pressure of 1500 psi. The effective content of MgO in minimizing and eliminating the generation of cracks was 2.0 wt%, which provided a moderate expansion of {ge} 0.5%. The compressive strength of 2.0 wt% MgO specimens made under a pressure of 300 psi rose {approx} 1.7-fold to 4816 psi with an increasing pressure to 1500 psi. The in-situ growth of brucite crystal formed by the hydrothermal hydration of MgO was responsive for such an expansion of the SSASC cement; meanwhile. two crystalline hydrothermal reaction products, 1.1 nm tobermorite and calcium silicate hydrated, contributed to the development of the sealer's compressive strength. Thus, the increasing pressure seems to suppress and control a growth rate of brucite crystal in response to a lower extension of expansion. Furthermore, all MgO-conlaining SSASC sealers possessed the water-catalyzed self-degradable properties.

  4. Effect of MgO Additive on Volumetric Expansion of Self-Degradable Cements

    Energy Technology Data Exchange (ETDEWEB)

    Sugama T.; Warren, J.; Butcher, T.

    2011-09-30

    We identified hard-burned magnesium oxide (MgO) as a suitable expansive additive for improving the plugging performance of self-degradable, temporary sodium silicate-activated slag/Class C fly ash (SSASC) blend cement sealers into rock fractures in Enhanced Geothermal Systems (EGSs). MgO extended the volumetric expansion of sealers during their exposure to a hydrothermal environment at 200 C under pressures, ranging from 300 to 1500 psi. A great expansion ratc of 19.3% was observed by adding 3.0 wt% MgO under 300 psi pressure, thus promising to plug thoroughly inner fracture. When the pressure was increased from 300 psi to 1500 psi, the expansion rate of cement markedly reduced, corresponding to the formaLion of crack-free specimens and the improvement of compressive strength. However, with 3.0 wt% MgO, the specimens still engendered the generation of numerous visual cracks, although they were prepared under a high pressure of 1500 psi. The effective content of MgO in minimizing and eliminating the generation of cracks was 2.0 wt%, which provided a moderate expansion of {ge} 0.5%. The compressive strength of 2.0 wt% MgO specimens made under a pressure of 300 psi rose {approx} 1.7-fold to 4816 psi with an increasing pressure to 1500 psi. The in-situ growth of brucite crystal formed by the hydrothermal hydration of MgO was responsive for such an expansion of the SSASC cement; meanwhile. two crystalline hydrothermal reaction products, 1.1 nm tobermorite and calcium silicate hydrated, contributed to the development of the sealer's compressive strength. Thus, the increasing pressure seems to suppress and control a growth rate of brucite crystal in response to a lower extension of expansion. Furthermore, all MgO-conlaining SSASC sealers possessed the water-catalyzed self-degradable properties.

  5. Volumetric runoff coefficients for experimental rural catchments in the Iberian Peninsula

    Science.gov (United States)

    Taguas, Encarnación V.; Molina, Cecilio; Nadal-Romero, Estela; Ayuso, José L.; Casalí, Javier; Cid, Patricio; Dafonte, Jorge; Duarte, Antonio C.; Farguell, Joaquim; Giménez, Rafael; Giráldez, Juan V.; Gómez, Helena; Gómez, Jose A.; González-Hidalgo, J. Carlos; Keizer, J. Jacob; Lucía, Ana; Mateos, Luciano; Rodríguez-Blanco, M. Luz; Schnabel, Sussane; Serrano-Muela, M. Pilar

    2015-04-01

    crucial for designing appropriate decision making tools for water management. REFERENCES Chow V.T., Maidment D.R. and Mays, L.W. 1988. Applied Hydrology. MCGraw Hill, Nueva York. Dhakal, N., Fang, X., Cleveland, T., Thompson, D., Asquith, W., and Marzen, L. (2012). "Estimation of Volumetric Runoff Coefficients for Texas Watersheds Using Land-Use and Rainfall-Runoff Data." Journal of Irrigation and Drainage Engineering, 1(2012):43-54. Schaake JC, Geyer JC,Knapp JW. 1967. Experimental examination of the rational method. J. Hydr.Div. 93(6),353-70

  6. Low coefficient of thermal expansion polyimides containing metal ion additives

    Science.gov (United States)

    Stoakley, D. M.; St. Clair, A. K.

    1992-01-01

    Polyimides have become widely used as high performance polymers as a result of their excellent thermal stability and toughness. However, lowering their coefficient of thermal expansion (CTE) would increase their usefulness for aerospace and electronic applications where dimensional stability is a requirement. The incorporation of metal ion-containing additives into polyimides, resulting in significantly lowered CTE's, has been studied. Various metal ion additives have been added to both polyamic acid resins and soluble polyimide solutions in the concentration range of 4-23 weight percent. The incorporation of these metal ions has resulted in reductions in the CTE's of the control polyimides of 12 percent to over 100 percent depending on the choice of additive and its concentration.

  7. Emerging morphologies in round bacterial colonies: comparing volumetric versus chemotactic expansion.

    Science.gov (United States)

    Giverso, Chiara; Verani, Marco; Ciarletta, Pasquale

    2016-06-01

    Biological experiments performed on living bacterial colonies have demonstrated the microbial capability to develop finger-like shapes and highly irregular contours, even starting from an homogeneous inoculum. In this work, we study from the continuum mechanics viewpoint the emergence of such branched morphologies in an initially circular colony expanding on the top of a Petri dish coated with agar. The bacterial colony expansion, based on either a source term, representing volumetric mitotic processes, or a nonconvective mass flux, describing chemotactic expansion, is modeled at the continuum scale. We demonstrate that the front of the colony is always linearly unstable, having similar dispersion curves to the ones characterizing branching instabilities. We also perform finite element simulations, which not only prove the emergence of branching, but also highlight dramatic differences between the two mechanisms of colony expansion in the nonlinear regime. Furthermore, the proposed combination of analytical and numerical analysis allowed studying the influence of different model parameters on the selection of specific patterns. A very good agreement has been found between the resulting simulations and the typical structures observed in biological assays. Finally, this work provides a new interpretation of the emergence of branched patterns in living aggregates, depicted as the results of a complex interplay among chemical, mechanical and size effects.

  8. Effects of volumetric expansion in molecular crystals: A quantum mechanical investigation on aspirin and paracetamol most stable polymorphs

    Science.gov (United States)

    Adhikari, Kapil; Flurchick, Kenneth M.; Valenzano, Loredana

    2015-02-01

    This work reports a study performed at hybrid semi-empirical density functional level (B3LYP-D2*) of the physico-chemical properties of aspirin (acetylsalicylic acid) and paracetamol (acetaminophen) in their most stable crystalline forms. It is shown how effects arising from volumetric expansions influence the properties of the materials. Structural, energetic, and vibrational properties are in good agreement with experimental values reported at temperatures far from 0 K. Results show that the proposed approach is reliable enough to reproduce effects of volumetric expansion on lattice energies and other measurable physico-chemical observables related to inter-molecular forces.

  9. Characterization of hydrological responses to rainfall and volumetric coefficients on the event scale in rural catchments of the Iberian Peninsula

    Science.gov (United States)

    Taguas, Encarnación; Nadal-Romero, Estela; Ayuso, José L.; Casalí, Javier; Cid, Patricio; Dafonte, Jorge; Duarte, Antonio C.; Giménez, Rafael; Giráldez, Juan V.; Gómez-Macpherson, Helena; Gómez, José A.; González-Hidalgo, J. Carlos; Lucía, Ana; Mateos, Luciano; Rodríguez-Blanco, M. Luz; Schnabel, Susanne; Serrano-Muela, M. Pilar; Lana-Renault, Noemí; Mercedes Taboada-Castro, M.; Taboada-Castro, M. Teresa

    2016-04-01

    Analysis of storm rainfall-runoff data is essential to improve our understanding of catchment hydrology and to validate models supporting hydrological planning. In a context of climate change, statistical and process-based models are helpful to explore different scenarios which might be represented by simple parameters such as volumetric runoff coefficient. In this work, rainfall-runoff event datasets collected at 17 rural catchments in the Iberian Peninsula were studied. The objectives were: i) to describe hydrological patterns/variability of the relation rainfall-runoff; ii) to explore different methodologies to quantify representative volumetric runoff coefficients. Firstly, the criteria used to define an event were examined in order to standardize the analysis. Linear regression adjustments and statistics of the rainfall-runoff relations were examined to identify possible common patterns. In addition, a principal component analysis was applied to evaluate the variability among catchments based on their physical attributes. Secondly, runoff coefficients at event temporal scale were calculated following different methods. Median, mean, Hawkinś graphic method (Hawkins, 1993), reference values for engineering project of Prevert (TRAGSA, 1994) and the ratio of cumulated runoff and cumulated precipitation of the event that generated runoff (Rcum) were compared. Finally, the relations between the most representative volumetric runoff coefficients with the physical features of the catchments were explored using multiple linear regressions. The mean volumetric runoff coefficient in the studied catchments was 0.18, whereas the median was 0.15, both with variation coefficients greater than 100%. In 6 catchments, rainfall-runoff linear adjustments presented coefficient of determination greater than 0.60 (p hydrological response differences in the catchments. REFERENCES: Hawkins, R. H. (1993). Asymptotic determination of runoff curve numbers from data. J. Irrig. Drain. Eng

  10. PREPARATION OF HIGH THERMAL EXPANSION COEFFICIENT PORCELAINS FUSED TO METALS

    Institute of Scientific and Technical Information of China (English)

    J.P. Yang; J.Q. Wu

    2003-01-01

    Usually the thermal expansion coefficients (TEC) of metals are higher than that of porcelains. In order to match the TECs in the case of coating porcelains on metals, high TEC porcelains are needed. In this research, the high TEC phase leucite(KAlSi2 O6) in the high TEC porcelain was prepared by sol-gel method. The crystal size of leucite made by sol-gel is about 77nm through controlling the process parameters. The process from xerogel to leucite was investigated by means of DSC (differential scanning calorimetry), TG (thermogravimetry), XRD ( X-ray diffraction) and IR(infrared absorption spectrum). Leucite had been detected after the gel was treated at 900°C, this formation temperature is about 250°C lower than that of melting method.The porcelain made from 50% of the leucite powder and 50%o of low fused temperature frit has an average TEC of 19.2× 10-6/° C from room temperature to 450°C, which is much higher than the common porcelains.

  11. The coefficient of bond thermal expansion measured by extended x-ray absorption fine structure.

    Science.gov (United States)

    Fornasini, P; Grisenti, R

    2014-10-28

    The bond thermal expansion is in principle different from the lattice expansion and can be measured by correlation sensitive probes such as extended x-ray absorption fine structure (EXAFS) and diffuse scattering. The temperature dependence of the coefficient α(bond)(T) of bond thermal expansion has been obtained from EXAFS for CdTe and for Cu. A coefficient α(tens)(T) of negative expansion due to tension effects has been calculated from the comparison of bond and lattice expansions. Negative lattice expansion is present in temperature intervals where α(bond) prevails over α(tens); this real-space approach is complementary but not equivalent to the Grüneisen theory. The relevance of taking into account the asymmetry of the nearest-neighbours distribution of distances in order to get reliable bond expansion values and the physical meaning of the third cumulant are thoroughly discussed.

  12. A Simple and Accurate Method for Calculating the Gaussian Beam Expansion Coefficients

    Institute of Scientific and Technical Information of China (English)

    LIU Wei; YANG Jun

    2010-01-01

    @@ The calculation of the diffraction field radiated from the ultrasonic transducer can be simplified by using the Gaussian beam expansion technique.The key problem of this technique is how to determine the coefficients of Gaussian functions.We present a simple and accurate optimization method to calculate the Gaussian beam expansion Coefficients.Half of the coefficients are obtained by solving linear equations.The other half are derived from the Fourier series expansion.Wave field simulation results demonstrate the validity of the new method.

  13. Calculation of thermal expansion coefficient of glasses based on topological constraint theory

    Science.gov (United States)

    Zeng, Huidan; Ye, Feng; Li, Xiang; Wang, Ling; Yang, Bin; Chen, Jianding; Zhang, Xianghua; Sun, Luyi

    2016-10-01

    In this work, the thermal expansion behavior and the structure configuration evolution of glasses were studied. Degree of freedom based on the topological constraint theory is correlated with configuration evolution; considering the chemical composition and the configuration change, the analytical equation for calculating the thermal expansion coefficient of glasses from degree of freedom was derived. The thermal expansion of typical silicate and chalcogenide glasses was examined by calculating their thermal expansion coefficients (TEC) using the approach stated above. The results showed that this approach was energetically favorable for glass materials and revealed the corresponding underlying essence from viewpoint of configuration entropy. This work establishes a configuration-based methodology to calculate the thermal expansion coefficient of glasses that, lack periodic order.

  14. Measurement of Linear Coefficient of Thermal Expansion and Temperature-Dependent Refractive Index Using Interferometric System

    Science.gov (United States)

    Corsetti, James A.; Green, William E.; Ellis, Jonathan D.; Schmidt, Greg R.; Moore, Duncan T.

    2017-01-01

    A system combining an interferometer with an environmental chamber for measuring both coefficient of thermal expansion (CTE) and temperature-dependent refractive index (dn/dT) simultaneously is presented. The operation and measurement results of this instrument are discussed.

  15. Defining chemical expansion: the choice of units for the stoichiometric expansion coefficient

    DEFF Research Database (Denmark)

    Marrocchelli, Dario; Chatzichristodoulou, Christodoulos; Bishop, Sean R.

    2014-01-01

    Chemical expansion refers to the spatial dilation of a material that occurs upon changes in its composition. When this dilation is caused by a gradual, iso-structural increase in the lattice parameter with composition, it is related to the composition change by the stoichiometric expansion coeffi...... are provided for changes in oxygen content in fluorite, perovskite, and Ruddlesden-Popper (K2NiF4) phase materials used in solid oxide fuel cells....

  16. Effect of graphene nanoplatelets on coefficient of thermal expansion of polyetherimide composite

    Energy Technology Data Exchange (ETDEWEB)

    Wu, Huang, E-mail: huang.wu.84@gmail.com [Composite Materials and Structures Center, Michigan State University, East Lansing, MI 48864 (United States); Department of Chemical Engineering and Material Science, Michigan State University, East Lansing, MI 48864 (United States); Drzal, Lawrence T. [Composite Materials and Structures Center, Michigan State University, East Lansing, MI 48864 (United States); Department of Chemical Engineering and Material Science, Michigan State University, East Lansing, MI 48864 (United States)

    2014-07-01

    Thermal expansion is one of the major concerns for polymer composites. In this research, graphene nanoplatelets (GNPs) were added to polyetherimide (PEId) thermoplastic polymer in order to reduce the coefficient of thermal expansion (CTE) of the injection molded composite. First, the coefficient of linear thermal expansion (LTE) was measured in three directions in the anisotropic coupon: 0°, 90° and the out of plane Z direction. It is found that the GNP particles are very effective in terms of reducing the LTE in 0° direction due to high degree of alignment. After annealing above glass transition temperature, significant increase of 0° LTE and decrease of Z° LTE were observed. The bulk CTE was calculated by adding up the LTEs in all three directions and is found to be independent of annealing. Second, several models were applied to predict both CTE and LTE. It is found that Schapery's lower limit model fits the experimental CTE very well. Chow's model was applied for LTEs in three directions. The behavior of GNP-5/PEId composites is explained by the combination of Chow's model and morphology obtained by scanning electron microscope (SEM). - Highlights: • Coefficient of thermal expansion (CTE) of polymer composite is characterized. • Reduction of linear thermal expansion depends on filler orientation. • Filler orientation is characterized based on the location of the specimen. • Filler orientation is changed by annealing, causing subsequent change in CTE. • CTE and linear thermal expansion coefficient are modeled.

  17. Volumetric gas-liquid mass transfer coefficient in an external-loop airlift reactor with inserted membrane

    Directory of Open Access Journals (Sweden)

    Kojić Predrag S.

    2016-01-01

    Full Text Available The effects of the inserted membrane in the downcomer of an external-loop airlift reactor, the gas sparger type (single orifice and sinter plate and added alcohol (ethanol, n-butanol, or n-hexanol on the volumetric gas-liquid mass transfer coefficient (kLa were studied. Due to the presence of the membrane in the downcomer, kLa did not change significantly; the differences were smaller than 10%. The highest values of the kLa were obtained using the sinter plate. It was found that the addition of small amounts of alcohol increased the mass transfer. Using our experimental results and the data of other authors, the feed-forward back propagation neural network for prediction of kLa in external-loop airlift reactors with alcohol solutions was proposed. [Projekat Ministarstva nauke Republike Srbije, br. 172025

  18. Modeling of Thermal Expansion Coefficients of Ni-Based Superalloys Using Artificial Neural Network

    Science.gov (United States)

    Bano, Nafisa; Nganbe, Michel

    2013-04-01

    The objective of this work is to model the thermal expansion coefficients of various Ni-based superalloys used in gas turbine components. The thermal expansion coefficient is described as a function of temperature, chemical composition including Ni, Cr, Co, Mo, W, Ta, Nb, Al, Ti, B, Zr, and C contents as well as heat treatment including solutionizing and aging. Experimental values are well described and their relative changes well correlated by the model. Because gas turbine engine components operate under severe loading conditions and at high and varying temperatures, the prediction of their thermal expansion coefficient is crucial. The model developed in this work can be useful for design optimizations for minimizing thermo-mechanical stresses between the base alloys and potential protective coatings or adjacent components. It can substantially contribute to improve the performance and service life of gas turbine components.

  19. Development of Zero Coefficient of Thermal Expansion composite tubes for stable space structures

    Science.gov (United States)

    Strock, John D.

    1992-09-01

    Advanced composite materials are well suited for stable space structures due to their low Coefficient of Thermal Expansion (CTE), high stiffness and light weight. For a given design application, composite hardware can be tailored for strength, stiffness, CTE, and Coefficient of Moisture Expansion (CME). Computer modeling and laminate testing of high modulus graphite/epoxy tubes were evaluated for compressive strength, stiffness, CTE, CME and microcracking. Thermal cycling and microcracking effects on CTE were evaluated. Thin graphite/epoxy plies exhibited reduced microcracking. A zero CTE thin wall tube design resulted from the development program. Recent work on low moisture absorption resin systems is also discussed.

  20. Grain size and film thickness effect on the thermal expansion coefficient of FCC metallic thin films.

    Science.gov (United States)

    Hwang, Seulgi; Kim, Youngman

    2011-08-01

    Thin films are used in wide range of applications in industry, such as solar cells and LEDs. When thin films are deposited on substrates, various stresses are generated due to the mechanical difference between the film and substrate. These stresses can cause defects, such as cracking and buckling. Therefore, knowledge of the mechanical properties is important for improving their reliability and stability. In this study, the thermal expansion coefficient of FCC metallic thin films, such as Ag and Cu, which have different grain sizes and thicknesses, were calculated using the thermal cycling method. As a result, thermal expansion coefficient increased with increasing grain size. However, the film thickness had no remarkable effect.

  1. Theoretical Prediction of Volumetric Mass Transfer Coefficient (kLa for Designing an Aeration Tank

    Directory of Open Access Journals (Sweden)

    Gilles Hebrard

    2009-11-01

    Full Text Available The objective of this present paper is to propose a new theoretical prediction method of the volumetric mass transfer coefficient (kLa occurring in a gas-liquid contactor based on the dissociation of the liquid-side mass transfer coefficient (kL and the interfacial area (a. The calculated results have been compared with those obtained with the experimental process in a small-scale bubble column. Tap water was used as liquid phase and an elastic membrane with a single orifice as gas sparger. Only the dynamic bubble regime was considered in this work (ReOR= 1501000 and We = 0.0024. This study has clearly shown that, whatever the operating conditions under test, the generated bubble diameters (dB, bubble frequency (fB and their associated rising velocities (UB were the important parameters in order to predict, not only the values of kLa, but also the values of a and of kL. Moreover, these obtained results could provide a better understanding of the parameters which influence the oxygen transfer mechanism in the aeration process. By using the correlations to estimate these bubble hydrodynamics (dB and UB, it diminishes times for measuring the associated mass transfer parameters and also their experimental complexities and errors.

  2. Molecular Dynamics Study of a Thermal Expansion Coefficient: Ti Bulk with an Elastic Minimum Image Method

    Institute of Scientific and Technical Information of China (English)

    Yakup Hundur; Rainer Hippler; Ziya B. Güven(c)

    2006-01-01

    @@ Linear thermal expansion coefficient (TEC) of Ti bulk is investigated by means of molecular dynamics simulation.The elastic minimum image convention of periodic boundary conditions is introduced to allow the bulk to adjust its size according to the new fixed temperature. The TEC and the specific heat of Ti are compared to the available theoretical and experimental data.

  3. Autofrettage to Counteract Coefficient of Thermal Expansion Mismatch in Cryogenic Pressurized Pipes with Metallic Liners

    Science.gov (United States)

    Wen, Ed; Barbero, Ever; Tygielski, Phlip; Turner, James E. (Technical Monitor)

    2001-01-01

    Composite feedlines with metal liners have the potential to reduce weight/cost while providing the same level of permeation resistance and material compatibility of all-metal feedlines carrying cryogenic propellants in spacecraft. The major technical challenges are the large difference in Coefficient of Thermal Expansion between the liner and the composite, and the manufacturing method required to make a very thin liner with the required strength and dimensional tolerance. This study investigates the use of autofrettage (compressive preload) to counteract Coefficient of Thermal Expansion when pre-pressurization procedures cannot be used to solve this problem. Promising materials (aluminum 2219, Inconel 718, nickel, nickel alloy) and manufacturing techniques (chemical milling, electroplating) are evaluated to determine the best liner candidates. Robust, autofrettaged feedlines with a low Coefficient of Thermal Expansion liner (Inconel 718 or nickel alloy) are shown to successfully counteract mismatch at LOX temperature. A new concept, autofrettage by temperature, is introduced for high Coefficient of Thermal Expansion materials (aluminum and pure nickel) where pressure cannot be used to add compressive preload.

  4. Calculation of Thermal Expansion Coefficients of Pure Elements and their Alloys

    Science.gov (United States)

    Abel, Phillip; Bozzolo, Guillermo; Huff, Dennis (Technical Monitor)

    2002-01-01

    A simple algorithm for computing the coefficient of thermal expansion of pure elements and their alloys, based on features of the binding energy curve, is introduced. The BFS method for alloys is used to determine the binding energy curves of intermetallic alloys and Ni-base superalloys.

  5. MULTISCALE ASYMPTOTIC EXPANSION FOR A CLASS OF HYPERBOLIC-PARABOLIC TYPE EQUATION WITH HIGHLY OSCILLATORY COEFFICIENTS

    Institute of Scientific and Technical Information of China (English)

    Li-qun Cao; De-chao Zhu; Jian-Lan Luo

    2002-01-01

    In this paper, we will discuss the asymptotic behaviour for a class of hyper bolic -parabolic type equation with highly oscillatory coefficients arising from the strong-transient heat and mass transfer problems of composite media. A complete multiscale asymptotic expansion and its rigorous verification will be reported.

  6. Effect of heat treatment on the thermal expansion coefficient of austempered ductile iron

    Energy Technology Data Exchange (ETDEWEB)

    Tadayon saidi, M. [Dept. Metallurgy-Karaj Azad Univ.-Karaj (Iran); Baghersaie, N. [Tehran Center, Control Dept., Eng. Research Inst., Ministry of Jihad Agriculture (Iran); Varahram, N. [RAZI Metallurgical Research Inst.-Tehran (Iran)

    2005-07-01

    Austempered ductile iron provide a unique combination of strength and toughness coupled with excellent design flexibility for automotive application as compared to forged or cast steels. Some material properties such as thermal expansion coefficient and its influence in final machining tolerance is a matter of discussion in the automotive industry. In this study the effect of heart treatment cycle on the microstructure and thermal expansion of ADI was investigated. Samples were austempered at 275 C and 375 C for one hour and then dilatometric test carried out in the temperature range of 50 C to 350 C, then the result was compared with the thermal expansion coefficient of forged steel. Microstructure and mechanical investigations were used to the assurance of these results. The results indicate that replacing of forged steel with ADI due to lower cost production and reduction in weight is possible if the correct tolerance were selected. (orig.)

  7. Asymptotic expansion based equation of state for hard-disk fluids offering accurate virial coefficients

    CERN Document Server

    Tian, Jianxiang; Mulero, A

    2016-01-01

    Despite the fact that more that more than 30 analytical expressions for the equation of state of hard-disk fluids have been proposed in the literature, none of them is capable of reproducing the currently accepted numeric or estimated values for the first eighteen virial coefficients. Using the asymptotic expansion method, extended to the first ten virial coefficients for hard-disk fluids, fifty-seven new expressions for the equation of state have been studied. Of these, a new equation of state is selected which reproduces accurately all the first eighteen virial coefficients. Comparisons for the compressibility factor with computer simulations show that this new equation is as accurate as other similar expressions with the same number of parameters. Finally, the location of the poles of the 57 new equations shows that there are some particular configurations which could give both the accurate virial coefficients and the correct closest packing fraction in the future when higher virial coefficients than the t...

  8. Thermal Expansion and Diffusion Coefficients of Carbon Nanotube-Polymer Composites

    Science.gov (United States)

    Wei, Chengyu; Srivastava, Deepak; Cho, Kyeongjae; Biegel, Bryan (Technical Monitor)

    2001-01-01

    Classical molecular dynamics (MD) simulations employing Brenner potential for intra-nanotube interactions and van der Waals forces for polymer-nanotube interface have been used to investigate thermal expansion and diffusion characteristics of carbon nanotube-polyethylene composites. Addition of carbon nanotubes to polymer matrix is found to significantly increase the glass transition temperature Tg, and thermal expansion and diffusion coefficients in the composite above Tg. The increase has been attributed to the temperature dependent increase of the excluded volume for the polymer chains, and the findings could have implications in the composite processing, coating and painting applications.

  9. Preparation and Characteristic of Glass-Ceramics with Super Low Thermal Expansion Coefficient

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    The preparation technics of glass-ceramics with super low coefficient of thermal expansion containing β-quartz solid solution as a main crystal phase based on the glass in the system Li2O-Al2O3-SiO2 was introduced. The composition of base glass, technics of melting and heat treatment effecting on characteristic of glass-ceramics was described. Specimens were prepared by melting, anneal and controlled two steps heat treatment. Crystal phase, microstructure and elementary distributing were studied by using XRD, SEM and EDS respectively. Prepared specimens show excellent transparency and super low thermal expansion coefficient of 2×10-8 ·K-1, which reaches international advanced level.

  10. Estimating the thermal expansion coefficient of graphene: the role of graphene-substrate interactions.

    Science.gov (United States)

    Shaina, P R; George, Lijin; Yadav, Vani; Jaiswal, Manu

    2016-03-02

    The temperature-dependent thermal expansion coefficient of graphene is estimated for as-grown chemical vapor deposited graphene using temperature-dependent Raman spectroscopy. For as-grown graphene on copper, the extent of thermal expansion mismatch between substrate and the graphene layer is significant across the entire measured temperature interval, T  =  90-300 K. This mismatch induces lattice strain in graphene. However, graphene grown on copper substrates has a unique morphology in the form of quasi-periodic nanoripples. This crucially influences the profile of the strain in the graphene membrane, which is uniaxial. An estimate of the thermal expansion coefficient of grapheme α(T) is obtained after consideration of this strain profile and after incorporating temperature-dependent Grüneisen parameter corrections. The value of α(T), is found to be negative (average value, -3.75  ×  10(-6) K(-1)) for the entire temperature range and it approaches close to zero for T  expansion and anharmonic contributions, and the data suggests limited interfacial interaction with the substrate.

  11. Digital image correlation method for calculating coefficients of Williams expansion in compact tension specimen

    Science.gov (United States)

    Ayatollahi, Majid R.; Moazzami, Mostafa

    2017-03-01

    The digital image correlation (DIC) method is used to obtain the coefficients of higher-order terms in the Williams expansion in a compact tension (CT) specimens made of polymethyl methacrylate (PMMA). The displacement field is determined by the correlation between reference image (i.e., before deformation) and deformed image. The part of displacements resulting from rigid body motion and rotation is eliminated from the displacement field. For a large number of points in the vicinity of the crack tip, an over-determined set of simultaneous linear equations is collected, and by using the fundamental concepts of the least-squares method, the coefficients of the Williams expansion are calculated for pure mode I conditions. The experimental results are then compared with the numerical results calculated by finite element method (FEM). Very good agreement is shown to exist between the DIC and FE results confirming the effectiveness of the DIC technique in obtaining the coefficients of higher order terms of Williams series expansion from the displacement field around the crack tip.

  12. Evaluation of thermal expansion coefficient of Fabry-Perot cavity using an optical frequency comb

    Science.gov (United States)

    Oulehla, Jindřich; Šmíd, Radek; Buchta, Zdeněk; Čížek, Martin; Mikel, Břetislav; Jedlička, Petr; Lazar, Josef; Číp, Ondřej

    2011-05-01

    In construction of highly mechanically stable measuring devices like AFM microscopes or nano-comparators the use of low expansion materials is very necessary. We can find Zerodur ceramics or ULE glasses used as a frame or basement of these devices. The expansion coefficient of such low-expansion materials is lower than 0.01 x 10-6 m•K-1. For example in case of a frame or basement 20 cm long it leads to a dilatation approximately 4 nm per 1 K. For calculation of the total uncertainty of the mentioned measuring devices the knowledge of the thermal expansion coefficient of the frame or basement is necessary. In this work we present a method, where small distance changes are transformed into rf-frequency signal. The frequency of this signal is detected by a counter which measures the value of the frequency with respect to an ultra-stable time-base. This method uses a Fabry-Perot cavity as a distance measuring tool. The spacer of the optical resonator is made from the investigated low-expansion material. It is placed into a vacuum chamber where the inside temperature is controlled. A selected mode of the femtosecond frequency of the femtosecond comb which represent the distance changes of the optical resonator. The frequency is measured by the rf-counter which is synchronized by a time-base signal from an atomic clock. The first results show the resolution of the method in the 0.1 nm order. Therefore the method has a potential in characterisation of materials in the nanoworld.

  13. The Effect of Homogenization Heat Treatment on Thermal Expansion Coefficient and Dimensional Stability of Low Thermal Expansion Cast Irons

    Science.gov (United States)

    Chen, Li-Hao; Liu, Zong-Pei; Pan, Yung-Ning

    2016-08-01

    In this paper, the effect of homogenization heat treatment on α value [coefficient of thermal expansion (10-6 K-1)] of low thermal expansion cast irons was studied. In addition, constrained thermal cyclic tests were conducted to evaluate the dimensional stability of the low thermal expansion cast irons with various heat treatment conditions. The results indicate that when the alloys were homogenized at a relatively low temperature, e.g., 1023 K (750 °C), the elimination of Ni segregation was not very effective, but the C concentration in the matrix was moderately reduced. On the other hand, if the alloys were homogenized at a relatively high temperature, e.g., 1473 K (1200 °C), opposite results were obtained. Consequently, not much improvement (reduction) in α value was achieved in both cases. Therefore, a compound homogenization heat treatment procedure was designed, namely 1473 K (1200 °C)/4 hours/FC/1023 K (750 °C)/2 hours/WQ, in which a relatively high homogenization temperature of 1473 K (1200 °C) can effectively eliminate the Ni segregation, and a subsequent holding stage at 1023.15 K (750 °C) can reduce the C content in the matrix. As a result, very low α values of around (1 to 2) × 10-6 K-1 were obtained. Regarding the constrained thermal cyclic testing in 303 K to 473 K (30 °C to 200 °C), the results indicate that regardless of heat treatment condition, low thermal expansion cast irons exhibit exceedingly higher dimensional stability than either the regular ductile cast iron or the 304 stainless steel. Furthermore, positive correlation exists between the α 303.15 K to 473.15 K value and the amount of shape change after the thermal cyclic testing. Among the alloys investigated, Heat I-T3B (1473 K (1200 °C)/4 hours/FC/1023 K (750 °C)/2 hours/WQ) exhibits the lowest α 303 K to 473 K value (1.72 × 10-6 K-1), and hence has the least shape change (7.41 μm) or the best dimensional stability.

  14. Anisotropy of Expansion Coefficient and Slag Resistance of Spinel Carbon Bricks

    Institute of Scientific and Technical Information of China (English)

    YANG Ding'ao; YUAN Shouqian; JIANG Mingxue; DONG Sunzhen; ZHAO Zijian

    2006-01-01

    Effects of the pressure direction on the thermal expansion and slag corrosion resistance were investigated and anisotropic microstructures of flaky graphite in spinel carbon bricks were examined. The experimental results show that slag corrosion velocities in the direction parallel to the pressure direction display a decrease of 34% compared to those in the vertical direction. Meantime, the linear expansion coefficient in the direction parallel to the pressure direction is 2.45 times as large as that in the vertical pressure direction. Slag corrosion velocities of spinel carbon bricks soaked in the AOD melting slag display a 46%-47% decrease compared to those of magnesia carbon bricks. The microstructure observation shows that spinel carbon bricks have a high degree of preferred orientation.

  15. SOME RESULTS ON THE COEFFICIENTS OF INTEGRATED EXPANSIONS OF ULTRASPHERICAL POLYNOMIALS AND THEIR INTEGRALS

    Institute of Scientific and Technical Information of China (English)

    E. H. Doha; S. I. El-Soubhy

    2001-01-01

    The formula of expressing the coefficients of an expansion ofultraspherical polynomials that has been integrated an arbitrary number of times in terms of the coefficients of the original expansion is stated in a more compact form and proved in a simpler way than the formula of Phillips and Karageorghis (1990). A new formula is proved for the q times integration of ultraspherical polynomials, of which the Chebyshev polynomials of the first and second kinds and Legendre polynomials are important special cases. An application of these formulae for solving ordinary differential equations with varying coefficients is discussed.CLC Number:O17 Document ID:AAuthor Resume:E. H. Doha,e-mail: eiddoha@frcu, eun. eg References:[1]Canuto,C. ,Spectral Methods in Fluid Dynamics,Springer,Belrin,1988.[2]Doha,E.H.,An Accurate Solution of Parabolic Equations by Expansion in Ultraspherical Polynomials,Comput. Math. Appl. ,19(1990),75-88.[3]Doha,E. H. ,The Coefficients of Differentiated Expansions and Derivatives of Ultraspherical Polynomials,Comput. Math. Appl.,21(1991),115-122.[4]Doha,E.H. ,The Chebyshev Coefficients of General order Derivatives of an Infinitely Differen-tiable Function in Two or Three Variables,Ann. Univ. Sci. Budapest. Sect. Comput. ,13(1992),83-91.[5]Doha,E. H.,On the Cefficients of Differentiable Expansions of Double and Triple Legendre Polynomials,Ann Univ. Sci. Budapest. Sect. Comput. ,15(1995),25-35.[6]Doha,E.H. ,The Ultraspherical Coefficients of the Moments of a General-Order Derivatives of an Infinitely Differentiable Function,J. Comput. Math. ,89(1998),53-72.[7]Doha,E.H. ,The Coefficients of Differentiated Expansions of Double and Triple Ultraspherical Polynomials,Annales Univ. Sci. Budapest.,Sect. Comp.,19(200),57-73.[8]Doha,E.H. and Al-Kholi,F. M. R. ,An Efficient Double Legerdre Spectral Method for Parabolic and Elliptic Partial Differential Equations,Intern. J. Computer. Math. (toAppear).[9]Fox,L. and Parker,I.B. ,Chebyshev Polynomials in

  16. Size- and Temperature-Dependent Thermal Expansion Coefficient of a Nanofilm

    Institute of Scientific and Technical Information of China (English)

    ZHOU Li-Jun; GUO Jian-Gang; ZHAO Ya-Pu

    2009-01-01

    The thermal expansion coefficient (TEC) of an ideal crystal is derived by using a method of Boltzmann statistics.The Morse potential energy function is adopted to show the dependence of the TEC on the temperature.By taking the effects of the surface relaxation and the surface energy into consideration,the dimensionless TEC of a nanofilm is derived.It is shown that with decreasing thickness,the TEC can increase or decrease,depending on the surface relaxation of the nanofilm.

  17. Sound velocity of high-strength polymer with negative thermal expansion coefficient

    Energy Technology Data Exchange (ETDEWEB)

    Nomura, R.; Ueno, M.; Okuda, Y.; Burmistrov, S.; Yamanaka, A

    2003-05-01

    Sound velocities of fiber reinforced plastics (FRPs) were measured along the fiber axis at temperatures between 360 and 77 K. We used two kinds of the high-strength crystalline polymer fibers, polyethylene (Dyneema) and polybenzobisoxazole (Zylon), which have negative thermal expansion coefficients. They also have high thermal conductivities and high resistances for flash over voltage, and are expected as new materials for coil bobbins or spacers at cryogenic temperatures. They have very large sound velocities of about 9000 (m/s) at 77 K, which are 4.5 times larger than that of the ordinary polyethylene fiber.

  18. Quasilinear diffusion coefficients in a finite Larmor radius expansion for ion cyclotron heated plasmas

    Science.gov (United States)

    Lee, Jungpyo; Wright, John; Bertelli, Nicola; Jaeger, Erwin F.; Valeo, Ernest; Harvey, Robert; Bonoli, Paul

    2017-05-01

    In this paper, a reduced model of quasilinear velocity diffusion by a small Larmor radius approximation is derived to couple the Maxwell's equations and the Fokker Planck equation self-consistently for the ion cyclotron range of frequency waves in a tokamak. The reduced model ensures the important properties of the full model by Kennel-Engelmann diffusion, such as diffusion directions, wave polarizations, and H-theorem. The kinetic energy change ( W ˙ ) is used to derive the reduced model diffusion coefficients for the fundamental damping (n = 1) and the second harmonic damping (n = 2) to the lowest order of the finite Larmor radius expansion. The quasilinear diffusion coefficients are implemented in a coupled code (TORIC-CQL3D) with the equivalent reduced model of the dielectric tensor. We also present the simulations of the ITER minority heating scenario, in which the reduced model is verified within the allowable errors from the full model results.

  19. Determination of the Thermal Expansion Coefficient of Concrete at Early Ages by Using Temperature-stress Testing Machine

    Institute of Scientific and Technical Information of China (English)

    HUO Kaicheng; SHUI Zhonghe; LI Yue

    2006-01-01

    By using the uptodate temperatuer-stress testing machine, the thermal expansion coefficient of concrete at early ages was studied and indicative conclusions were achieved: temperature rising due to hydration heat is not directly correlated with cracking, but the temperature and stress evolution process should be taken into consideration in the same time. Proper chemical admixtures and mineral compositions can improve the mechanical properties of concrete such as thermal expansion coefficient, which is very indicative in practice.

  20. Measurement of thermal expansion coefficient of graphene diaphragm using optical fiber Fabry-Perot interference

    Science.gov (United States)

    Li, Cheng; Liu, Qianwen; Peng, Xiaobin; Fan, Shangchun

    2016-07-01

    Application of the Fabry-Perot (FP) interference method for determining the coefficient of thermal expansion (CTE) of a graphene diaphragm is investigated in this paper. A miniature extrinsic FP interferometric (EFPI) sensor was fabricated by using an approximate 8-layer graphene diaphragm. The extremely thin diaphragm was transferred onto the endface of a ferrule with an inner diameter of 125 μm, and van der Waals interactions between the graphene diaphragm and its substrate created a low finesse FP interferometer with a cavity length of 36.13 μm. Double reference FP cavities using two cleaved optical fibers as reflectors were also constructed to differentially cancel the thermal expansion effects of the trapped gas and adhesive material. A temperature test demonstrated an approximate cavity length change of 166.1 nm °C-1 caused by film thermal expansion in the range of 20-60 °C. Then along with the established thermal deformation model of the suspended circular diaphragm, the calculated CTE ranging from  -9.98  ×  10-6 K-1 to  -2.09  ×  10-6 K-1 conformed well to the previously measured results. The proposed method would be applicable in other types of elastic materials as the sensitive diaphragm of an EFPI sensor over a wide temperature range.

  1. Cryogenic Refractive Index and Coefficient of Thermal Expansion for the S-TIH1 Glass

    Science.gov (United States)

    Quijada, Manuel A.; Leviton, Douglas; Content, David

    2013-01-01

    Using the CHARMS facility at NASA GSFC, we have measured the cryogenic refractive index of the Ohara S-TIH1 glass from 0.40 to 2.53 micrometers and from 120 to 300 K. We have also examined the spectral dispersion and thermo-optic coefficients (dn/dT). We also derived temperature-dependent Sellmeier models from which refractive index may be calculated for any wavelength and temperature within the stated ranges of each model. The S-TIH1 glass we tested exhibited unusual behavior in the thermo-optic coefficient. We found that for delta index of refraction decrease with a decrease in temperature (positive dn/dT). However, the situation was reversed for delta larger than 0.63 micrometers, where the index will increase with a decrease in temperature (negative dn/dT). We also measured the coefficient of thermal expansion (CTE) for the similar batch of S-TIH1 glass in order to understand its thermal properties. The CTE showed a monotonic change with a decrease in temperature.

  2. Micro-Structured Two-Component 3D Metamaterials with Negative Thermal-Expansion Coefficient from Positive Constituents

    Science.gov (United States)

    Qu, Jingyuan; Kadic, Muamer; Naber, Andreas; Wegener, Martin

    2017-01-01

    Controlling the thermal expansion of materials is of great technological importance. Uncontrolled thermal expansion can lead to failure or irreversible destruction of structures and devices. In ordinary crystals, thermal expansion is governed by the asymmetry of the microscopic binding potential, which cannot be adjusted easily. In artificial crystals called metamaterials, thermal expansion can be controlled by structure. Here, following previous theoretical work, we fabricate three-dimensional (3D) two-component polymer micro-lattices by using gray-tone laser lithography. We perform cross-correlation analysis of optical microscopy images taken at different sample temperatures. The derived displacement-vector field reveals that the thermal expansion and resulting bending of the bi-material beams leads to a rotation of the 3D chiral crosses arranged onto a 3D checkerboard pattern within one metamaterial unit cell. These rotations can compensate the expansion of the all positive constituents, leading to an effectively near-zero thermal length-expansion coefficient, or over-compensate the expansion, leading to an effectively negative thermal length-expansion coefficient. This evidences a striking level of thermal-expansion control.

  3. Influence of fluid-mechanical characteristics of the system on the volumetric mass transfer coefficient and gas dispersion in three-phase system

    Directory of Open Access Journals (Sweden)

    Knežević Milena M.

    2014-01-01

    Full Text Available Distribution of gas bubbles and volumetric mass transfer coefficient, Kla, in a three phase system, with different types of solid particles at different operation conditions were studied in this paper. The ranges of superficial gas and liquid velocities used in this study were 0,03-0,09 m/s and 0-0,1 m/s, respectively. The three different types of solid particles were used as a bed in the column (glass dp=3 mm, dp=6 mm; ceramic dp=6 mm. The experiments were carried out in a 2D plexiglas column, 278 x 20,4 x 500 mm and in a cylindrical plexiglas column, with a diameter of 64 mm and a hight of 2000 mm. The Kla coefficient increased with gas and liquid velocities. Results showed that the volumetric mass transfer coefficient has a higher values in three phase system, with solid particles, compared with two phase system. The particles properties (diameter and density have a major impact on oxygen mass transfer in three phase systems.

  4. Transverse Coefficient of Thermal Expansion Measurements of Carbon Fibers Using ESEM at High Temperatures

    Science.gov (United States)

    Ochoa, O.; Jiang, J.; Putnam, D.; Lo, Z.; Ellis, A.; Effinger, Michael

    2003-01-01

    The transverse coefficient of thermal expansion (CTE) of single IM7, T1000, and P55 carbon fibers are measured at elevated temperatures. The specimens are prepared by press-fitting fiber tows into 0.7mm-diameter cavity in a graphite disk of 5mm in diameter and 3mm high. The specimens are placed on a crucible in an ESEM, and images of the fiber cross section are taken as the fibers are heated up to 800 C. Holding time, heating and cool down cycles are also introduced. The geometrical changes are measured using a graphics tablet. The change in area/perimeter is calculated to determine the strain and transverse CTE for each fiber. In a complimentary computational effort, displacements and stresses are calculated with finite element models.

  5. Multilayer Article Characterized by Low Coefficient of Thermal Expansion Outer Layer

    Science.gov (United States)

    Lee, Kang N. (Inventor)

    2004-01-01

    A multilayer article comprises a substrate comprising a ceramic or a silicon-containing metal alloy. The ceramic is a Si-containing ceramic or an oxide ceramic with or without silicon. An outer layer overlies the substrate and at least one intermediate layer is located between the outer layer and thc substrate. An optional bond layer is disposed between thc 1 least one intermediate layer and thc substrate. The at least one intermediate layer may comprise an optional chemical barrier layer adjacent the outer layer, a mullite-containing layer and an optional chemical barrier layer adjacent to the bond layer or substrate. The outer layer comprises a compound having a low coefficient of thermal expansion selected from one of the following systems: rare earth (RE) silicates; at least one of hafnia and hafnia-containing composite oxides; zirconia-containing composite oxides and combinations thereof.

  6. Thermal expansion coefficient of graphene using molecular dynamics simulation: A comparative study on potential functions

    Science.gov (United States)

    Ghasemi, Hamid; Rajabpour, Ali

    2017-01-01

    In this paper, we studied the thermal expansion coefficient (TEC) of pristine graphene sheets (GSs) using molecular dynamics (MD) simulation. We validated our model with previous studies employing AIREBO potential function and repeated the same simulation with the optimized Tersoff potential function. We also discussed the differences of the results and the corresponding reasons: evaluating the negative TEC of graphene by measuring the C-C bond length and out-of-plane vibrations of the GS. We finally showed that the ripples and wrinkles are more represented over the GS during the simulation with the AIREBO potential function rather than the optimized Tersoff. Comparing the results of both potential functions; it is seen that the results obtained by AIREBO potential function are in better agreement with those reported by previous scholars.

  7. CP: AN INVESTIGATION OF COEFFICIENT OF THERMAL EXPANSION, DECOMPOSITION KINETICS, AND REACTION TO VARIOUS STIMULI

    Energy Technology Data Exchange (ETDEWEB)

    Weese, R K; Burnham, A K; Fontes, A T

    2005-03-23

    The properties of pentaamine (5-cyano-2H-tetrazolato-N2) cobalt (III) perchlorate (CP), which was first synthesized in 1968, continues to be of interest for predicting behavior in handling, shipping, aging, and thermal cook-off situations. We report coefficient of thermal expansion (CTE) values over four specific temperature ranges, decomposition kinetics using linear heating rates, and the reaction to three different types of stimuli: impact, spark, and friction. The CTE was measured using a Thermal Mechanical Analyzer (TMA) for samples that were uniaxially compressed at 10,000 psi and analyzed over a dynamic temperature range of -20 C to 70 C. Using differential scanning calorimetry, DSC, CP was decomposed at linear heating rates of 1, 3, and 7 C/min and the kinetic triplet calculated using the LLNL code Kinetics05. Values are also reported for spark, friction, and impact sensitivity.

  8. Models of coefficient of thermal expansion (CTE) for Gilsocarbon graphites irradiated in inert and oxidising environments

    Energy Technology Data Exchange (ETDEWEB)

    Eason, Ernest D., E-mail: eeason@ix.netcom.com [Modeling and Computing Services, P.O. Box 18583, Boulder, CO 80308 (United States); Hall, Graham N., E-mail: graham.n.hall@manchester.ac.uk [Nuclear Graphite Research Group, School of Mechanical, Aerospace and Civil Engineering, University of Manchester, Manchester M13 9PL (United Kingdom); Marsden, Barry J., E-mail: barry.j.marsden@manchester.ac.uk [Nuclear Graphite Research Group, School of Mechanical, Aerospace and Civil Engineering, University of Manchester, Manchester M13 9PL (United Kingdom); Heys, Graham B., E-mail: Graham.Heys@hse.gsi.gov.uk [Office for Nuclear Regulation, An Agency of the Health and Safety Executive, Building 3, Redgrave Court, Merton Road, Bootle, Merseyside L20 7HS (United Kingdom)

    2013-05-15

    This paper presents the development and validation of an empirical model of radiation effects on coefficient of thermal expansion (CTE) for the Gilsocarbon graphites used in Advanced Gas-cooled Reactors (AGRs). The combined irradiation and oxidation model is based in part on a new model of fast neutron damage in inert environment. The new inert model shows an increase to an “upper shelf” irradiated CTE value at very low dose, then CTE values decrease with increasing dose following a hyperbolic tangent function. The effect of the actual exposure in AGRs is modelled by shifting the inert model in both dose and CTE directions to agree with the CTE measurements on material trepanned from moderator bricks in operating AGRs. The shift in the inert model that is needed to match the trepanned data varies significantly by reactor. The new model predicts randomly-selected validation data that were not used in model fitting as well as it fits the calibration data.

  9. A Micro-Test Structure for the Thermal Expansion Coefficient of Metal Materials

    Directory of Open Access Journals (Sweden)

    Qingying Ren

    2017-02-01

    Full Text Available An innovative micro-test structure for detecting the thermal expansion coefficient (TEC of metal materials is presented in this work. Throughout this method, a whole temperature sensing moveable structures are supported by four groups of cascaded chevrons beams and packed together. Thermal expansion of the metal material causes the deflection of the cascaded chevrons, which leads to the capacitance variation. By detecting the capacitance value at different temperatures, the TEC value of the metal materials can be calculated. A finite element model has been established to verify the relationship between the TEC of the material and the displacement of the structure on horizontal and vertical directions, thus a function of temperature for different values of TEC can be deduced. In order to verify the analytical model, a suspended-capacitive micro-test structure has been fabricated by MetalMUMPs process and tested in a climate chamber. Test results show that in the temperature range from 30 °C to 80 °C, the TEC of the test material is 13.4 × 10−6 °C−1 with a maximum relative error of 0.8% compared with the given curve of relationship between displacement and temperature.

  10. Cryogenic coefficient of thermal expansion measurements of type 440 and 630 stainless steel

    Science.gov (United States)

    Cease, H.; Alvarez, M.; Flaugher, B.; Montes, J.

    2014-01-01

    The Dark Energy Camera is now installed on the Blanco 4m telescope at the Cerro Tololo Inter-American Observatory in Chile. The camera is cooled to 170K using a closed loop two-phase liquid nitrogen system. A submerged centrifugal pump is used to circulate the liquid from the base of the telescope to the camera in the prime focus cage. As part of the pump maintenance schedule, the rotor shaft bearings are periodically replaced. Common bearing and shaft materials are type 440 and 630 (17-4 PH) stainless steel. The coefficient of thermal expansion of the materials used is needed to predict the shaft and bearing housing dimensional changes at the 77K pump operating temperature. The thermal expansion from room temperature to 77K of type 440 and 630 stainless steel is presented . Measurements are performed using the ASTM E228 standard with a quartz push-rod dilatometer test stand. Aluminum 6061-T6 is used to calibrate the test stand.

  11. Modified Fourth-Order Kinetic Energy Gradient Expansion with Hartree Potential-Dependent Coefficients.

    Science.gov (United States)

    Constantin, Lucian A; Fabiano, Eduardo; Della Sala, Fabio

    2017-09-12

    Using the semiclassical neutral atom theory, we developed a modified fourth-order kinetic energy (KE) gradient expansion (GE4m) that keeps unchanged all the linear-response terms of the uniform electron gas and gives a significant improvement with respect to the known semilocal functionals for both large atoms and jellium surfaces. On the other hand, GE4m is not accurate for light atoms; thus, we modified the GE4m coefficients making them dependent on a novel ingredient, the reduced Hartree potential, recently introduced in the Journal of Chemical Physics 2016, 145, 084110, in the context of exchange functionals. The resulting KE gradient expansion functional, named uGE4m, belongs to the novel class of u-meta-generalized-gradient-approximations (uMGGA) whose members depend on the conventional ingredients (i.e., the reduced gradient and Laplacian of the density) as well as on the reduced Hartree potential. To test uGE4m, we defined an appropriate benchmark (including total KE and KE differences for atoms, molecules and jellium clusters) for gradient expansion functionals, that is, including only those systems which are mainly described by a slowly varying density regime. While most of the GGA and meta-GGA KE functionals (we tested 18 of them) are accurate for some properties and inaccurate for others, uGE4m shows a consistently good performance for all the properties considered. This represents a qualitative boost in the KE functional development and highlights the importance of the reduced Hartree potential for the construction of next-generation KE functionals.

  12. Composite Laminate With Coefficient of Thermal Expansion Matching D263 Glass

    Science.gov (United States)

    Robinson, David; Rodini, Benjamin

    2012-01-01

    The International X-ray Observatory project seeks to make an X-ray telescope assembly with 14,000 flexible glass segments. The glass used is commercially available SCHOTT D263 glass. Thermal expansion causes the mirror to distort out of alignment. A housing material is needed that has a matching coefficient of thermal expansion (CTE) so that when temperatures change in the X-ray mirror assembly, the glass and housing pieces expand equally, thus reducing or eliminating distortion. Desirable characteristics of this material include a high stiffness/weight ratio, and low density. Some metal alloys show promise in matching the CTE of D263 glass, but their density is high compared to aluminum, and their stiffness/weight ratio is not favorable. A laminate made from carbon fiber reinforced plastic (CFRP) should provide more favorable characteristics, but there has not been any made with the CTE matching D263 Glass. It is common to create CFRP laminates of various CTEs by stacking layers of prepreg material at various angles. However, the CTE of D263 glass is 6.3 ppm/ C at 20 C, which is quite high, and actually unachievable solely with carbon fiber and resin. A composite laminate has been developed that has a coefficient of thermal expansion identical to that of SCHOTT D263 glass. The laminate is made of a combination of T300 carbon fiber, Eglass, and RS3C resin. The laminate has 50% uni-T300 plies and 50% uni-E-glass plies, with each fiber-layer type laid up in a quasi-isotropic laminate for a total of 16 plies. The fiber volume (percent of fiber compared to the resin) controls the CTE to a great extent. Tests have confirmed that a fiber volume around 48% gives a CTE of 6.3 ppm/ C. This is a fairly simple composite laminate, following well established industry procedures. The unique feature of this laminate is a somewhat unusual combination of carbon fiber with E-glass (fiberglass). The advantage is that the resulting CTE comes out to 6.3 ppm/ C at 20 C, which matches D

  13. Wave field synthesis of a sound field described by spherical harmonics expansion coefficients.

    Science.gov (United States)

    Ahrens, Jens; Spors, Sascha

    2012-03-01

    Near-field compensated higher order Ambisonics (NFC-HOA) and wave field synthesis (WFS) constitute the two best-known analytic sound field synthesis methods. While WFS is typically used for the synthesis of virtual sound scenes, NFC-HOA is typically employed in order to synthesize sound fields that have been captured with appropriate microphone arrays. Such recorded sound fields are essentially represented by the coefficients of the underlying surface spherical harmonics expansion. A sound field described by such coefficients cannot be straightforwardly synthesized in WFS. This is a consequence of the fact that, unlike in NFC-HOA, it is critical in WFS to carefully select those loudspeakers that contribute to the synthesis of a given sound source in a sound field under consideration. In order to enable such a secondary source selection, it is proposed to employ the well-known concept of decomposing the sound field under consideration into a continuum of plane waves, for which the secondary source selection is straightforward. The plane wave representation is projected onto the horizontal plane and a closed form expression of the secondary source driving signals for horizontal WFS systems of arbitrary convex shape is derived.

  14. Experimental investigation of the liquid volumetric mass transfer coefficient for upward gas-liquid two-phase flow in rectangular microchannels

    Directory of Open Access Journals (Sweden)

    X. Y. Ji

    2010-12-01

    Full Text Available The gas-liquid two-phase mass transfer process in microchannels is complicated due to the special dynamical characteristics. In this work, a novel method was explored to measure the liquid side volumetric mass transfer coefficient kLa. Pressure transducers were utilized to measure the pressure variation of upward gas-liquid two-phase flow in three vertical rectangular microchannels and the liquid side volumetric mass transfer coefficient kLa was calculated through the Pressure-Volume-Temperature correlation of the gas phase. Carbon dioxide-water, carbon dioxide-ethanol and carbon dioxide-n-propanol were used as working fluids, respectively. The dimensions of the microchannels were 40 µm×240 µm (depth×width, 100 µm×800 µm and 100 µm×2000 µm, respectively. Results showed that the channel diameter and the capillary number influence kLa remarkably and that the maximum value of kLa occurs in the annular flow regime. A new correlation of kLa was proposed based on the Sherwood number, Schmidt number and the capillary number. The predicted values of kLa agreed well with the experimental data.

  15. Local overall volumetric gas-liquid mass transfer coefficients in gas-liquid-solid reversed flow jet loop bioreactor with a non-Newtonian fluid.

    Science.gov (United States)

    Jianping; Ping; Lin; Yunlin

    2000-07-01

    The local overall volumetric gas-liquid mass transfer coefficients at the specified point in a gas-liquid-solid three-phase reversed flow jet loop bioreactor (JLB) with a non-Newtonian fluid was experimentally investigated by a transient gassing-in method. The effects of liquid jet flow rate, gas jet flow rate, particle density, particle diameter, solids loading, nozzle diameter and CMC concentration on the local overall volumetric gas-liquid mass transfer coefficient (K(L)a) profiles were discussed. It was observed that local overall K(L)a profiles in the three-phase reversed flow JLB with non-Newtonian fluid increased with the increase of gas jet flow rate, liquid jet flow rate, particle density and particle diameter, but decreased with the increase of the nozzle diameter and CMC concentration. The presence of solids at a low concentration increased the local overall K(L)a profiles, and the optimum of solids loading for a maximum profile of the local overall K(L)a was found to be 0.18x10(-3)m(3) corresponding to a solids volume fraction, varepsilon(S)=2.8%.

  16. The effect of grain size and film thickness on the thermal expansion coefficient of copper thin films.

    Science.gov (United States)

    Hwang, Seulgi; Kim, Youngman

    2011-02-01

    Cu thin films underwent thermal cycling to determine their coefficient of thermal expansion (CTE). The thermal stress of the Cu thin films with various microstructures (different grain size and film thickness) was measured using a curvature measurement system. The thermal expansion coefficients of the films were obtained from the slope of the stress-temperature curve with the knowledge of the Young's modulus and Poisson's ratio. The change in thermal stress with temperature of the Cu thin films tended to decrease with increasing grain size, resulting in an increase in the CTE. The thickness of Cu thin film had little effect on the thermal stress or the CTE.

  17. Thermal expansion coefficient prediction of fuel-cell seal materials from silica sand

    Science.gov (United States)

    Hidayat, Nurul; Triwikantoro, Baqiya, Malik A.; Pratapa, Suminar

    2013-09-01

    This study is focused on the prediction of coefficient of thermal expansion (CTE) of silica-sand-based fuel-cell seal materials (FcSMs) which in principle require a CTE value in the range of 9.5-12 ppm/°C. A semi-quantitative theoretical method to predict the CTE value is proposed by applying the analyzed phase compositions from XRD data and characterized density-porosity behavior. A typical silica sand was milled at 150 rpm for 1 hour followed by heating at 1000 °C for another hour. The sand and heated samples were characterized by means of XRD to perceive the phase composition correlation between them. Rietveld refinement was executed to investigate the weight fraction of the phase contained in the samples, and then converted to volume fraction for composite CTE calculations. The result was applied to predict their potential physical properties for FcSM. Porosity was taken into account in the calculation after which it was directly measured by the Archimedes method.

  18. Coefficient of Thermal Expansion of the Beta and Delta Polymorphs of HMX

    Energy Technology Data Exchange (ETDEWEB)

    Weese, R K; Burnham, A K; Maienschein, J L

    2004-08-05

    Dimensional changes related to temperature cycling of the beta and delta polymorphs of HMX (octahydro-1,3,5,7-tetranitro-1,3,5,7-tetrazocine) are important for a variety of applications. The coefficient of thermal expansion (CTE) of the beta and delta phases are measured and reported in this work over a temperature range of -20 C to 215 C. In addition, dimensional changes associated with the phase transition were measured, both through the transition and back down. Initially, differential scanning calorimetry (DSC) was used to investigate back conversion of the delta phase to the beta phase polymorph. The most successful approach was first to measure the amount of the beta to delta conversion, then after a given cooling period a repeat analysis, to measure the heat consumed by a second pass through the beta to delta phase transition. In addition, TMA is used to measure the dimensional change of a 0.20-gram sample of HMX during its initial heating and then three days later during a 2nd heating. This HMX shows the beta to delta phase transition a second time, thereby confirming the back conversion from delta to beta phase HMX.

  19. PROPERTIES OF CP: COEFFICIENT OF THERMAL EXPANSION, DECOMPOSITION KINETICS, AND REACTION TO SPARK, FRICTION AND IMPACT

    Energy Technology Data Exchange (ETDEWEB)

    Weese, R K; Burnham, A K

    2005-09-28

    The properties of pentaamine (5-cyano-2H-tetrazolato-N2) cobalt (III) perchlorate (CP), which was first synthesized in 1968, continues to be of interest for predicting behavior in handling, shipping, aging, and thermal cook-off situations. We report coefficient of thermal expansion (CTE) values over four specific temperature ranges, decomposition kinetics using linear and isothermal heating, and the reaction to three different types of stimuli: impact, spark, and friction. The CTE was measured using a Thermal Mechanical Analyzer (TMA) for samples that were uniaxially compressed at 10,000 psi and analyzed over a dynamic temperature range of -20 C to 70 C. Differential scanning calorimetry, DSC, was used to monitor CP decomposition at linear heating rates of 1-7 C min{sup -1} in perforated pans and of 0.1-1.0 C min{sup -1} in sealed pans. The kinetic triplet was calculated using the LLNL code Kinetics05, and predictions for 210 and 240 C are compared to isothermal thermogravimetric analysis (TGA) experiments. Values are also reported for spark, friction, and impact sensitivity.

  20. Measurements of the densities, isobaric thermal expansion coefficients and isothermal compressibilities of linear alkylbenzene in large liquid scintillator detectors

    CERN Document Server

    Zhou, Xiang; Liu, Qian; Zhang, Zhenyu; Ding, Yayun; Zhou, Li; Cao, Jun

    2014-01-01

    We report the measurements of the densities of linear alkylbenzene at three temperatures over 4 to 23 Celsius degree with pressures up to 10 MPa. The measurements have been analysed to yield the isobaric thermal expansion coefficients and, so far for the first time, isothermal compressibilities of linear alkylbenzene.

  1. Size- and temperature-dependent Young's modulus and size-dependent thermal expansion coefficient of thin films.

    Science.gov (United States)

    Zhou, Xiao-Ye; Huang, Bao-Ling; Zhang, Tong-Yi

    2016-08-21

    Nanomaterials possess a high surface/volume ratio and surfaces play an essential role in size-dependent material properties. In the present study, nanometer-thick thin films were taken as an ideal system to investigate the surface-induced size- and temperature-dependent Young's modulus and size-dependent thermal expansion coefficient. The surface eigenstress model was further developed with the consideration of thermal expansion, leading to analytic formulas of size- and temperature-dependent Young's modulus, and size-dependent thermal expansion coefficient of thin films. Molecular dynamics (MD) simulations on face-centered cubic (fcc) Ag, Cu, and Ni(001) thin films were conducted at temperatures ranging from 300 K to 600 K. The MD simulation results are perfectly consistent with the theoretical predictions, thereby verifying the theoretical approach. The newly developed surface eigenstress model will be able to attack similar problems in other types of nanomaterials.

  2. Nanoparticle shapes of LiMnPO4, Li+ diffusion orientation and diffusion coefficients for high volumetric energy Li+ ion cathodes

    Science.gov (United States)

    Kwon, Nam Hee; Yin, Hui; Vavrova, Tatiana; Lim, Jonathan H.-W.; Steiner, Ullrich; Grobéty, Bernard; Fromm, Katharina M.

    2017-02-01

    Nanoparticles of LiMnPO4 were fabricated in rod, elongated as well as cubic shapes. The 1D Li+ preferred diffusion direction for each shape was determined via electron diffraction spot patterns. The shape of nano-LiMnPO4 varied the diffusion coefficient of Li+ because the Li+ diffusion direction and the path length were different. The particles with the shortest dimension along the b-axis provided the highest diffusion coefficient, resulting in the highest gravimetric capacity of 135, 100 and 60 mAh g-1 at 0.05C, 1C and 10C, respectively. Using ball-milling, a higher loading of nano-LiMnPO4 in the electrode was achieved, increasing the volumetric capacity to 263 mAh cm-3, which is ca. 3.5 times higher than the one obtained by hand-mixing of electrode materials. Thus, the electrochemical performance is governed by both the diffusion coefficient of Li+, which is dependent on the shape of LiMnPO4 nanoparticles and the secondary composite structure.

  3. Thermo-optic and thermal expansion coefficients of RTP and KTP crystals over 300-350 K

    CERN Document Server

    Smith, Arlee V; Do, Binh T

    2016-01-01

    We report new measurements of the thermal expansion and thermo-optic coefficients of RbTiOPO$_4$ (RTP) and KTiOPO$_4$ (KTP) crystals over the temperature range 300-350 K. For RTP/KTP our coefficients of linear thermal expansion at 305 K are: $\\alpha_x=9.44/7.88\\times 10^{-6}$/K, $\\alpha_y=12.49/9.48\\times 10^{-6}$/K, $\\alpha_z=-4.16/0.02\\times 10^{-6}$/K. Our normalized thermo-optic coefficients $\\beta=(1/n)dn/dT$ at 632.8 nm and 305 K are: $\\beta_x=5.39/3.78\\times 10^{-6}$/K, $\\beta_y=7.11/5.24\\times 10^{-6}$/K, $\\beta_z=12.35/9.34\\times 10^{-6}$/K.

  4. Determination of Coefficient of Thermal Expansion (CTE) of 20MPa Mass Concrete Using Granite Aggregate

    Science.gov (United States)

    Chee Siang, GO

    2017-07-01

    Experimental test was carried out to determine the coefficient of thermal expansion (CTE) value of 20MPa mass concrete using granite aggregate. The CTE value was established using procedure proposed by Kada et al. 2002 in determining the magnitude of early-ages CTE through laboratory test which is a rather accurate way by eliminating any possible superimposed effect of others early-age thermal deformation shrinkages such as autogenous, carbonation, plastic and drying shrinkage. This was done by submitting granite concrete block samples instrumented with ST4 vibrating wire extensometers to thermal shocks. The response of the concrete samples to this shock results in a nearly instantaneous deformation, which are measured by the sensor. These deformations, as well as the temperature signal, are used to calculate the CTE. By repeating heat cycles, the variation in the early-ages of concrete CTE over time was monitored and assessed for a period of upto 7 days. The developed CTE value facilitating the verification and validation of actual maximum permissible critical temperature differential limit (rather than arbitrarily follow published value) of cracking potential. For thick sections, internal restraint is dominant and this is governed by differentials mainly. Of the required physical properties for thermal modelling, CTE is of paramount importance that with given appropriate internal restraint factor the condition of cracking due to internal restraint is governs by equation, ΔTmax= 3.663ɛctu / αc. Thus, it can be appreciated that an increase in CTE will lower the maximum allowable differential for cracking avoidance in mass concrete while an increase of tensile strain capacity will increase the maximum allowable temperature differential.

  5. Correlation between metal-ceramic bond strength and coefficient of linear thermal expansion difference

    Directory of Open Access Journals (Sweden)

    Stella Crosara Lopes

    2009-04-01

    Full Text Available The purpose of this study was to evaluate the metal-ceramic bond strength (MCBS of 6 metal-ceramic pairs (2 Ni-Cr alloys and 1 Pd-Ag alloy with 2 dental ceramics and correlate the MCBS values with the differences between the coefficients of linear thermal expansion (CTEs of the metals and ceramics. Verabond (VB Ni-Cr-Be alloy, Verabond II (VB2, Ni-Cr alloy, Pors-on 4 (P, Pd-Ag alloy, and IPS (I and Duceram (D ceramics were used for the MCBS test and dilatometric test. Forty-eight ceramic rings were built around metallic rods (3.0 mm in diameter and 70.0 mm in length made from the evaluated alloys. The rods were subsequently embedded in gypsum cast in order to perform a tensile load test, which enabled calculating the CMBS. Five specimens (2.0 mm in diameter and 12.0 mm in length of each material were made for the dilatometric test. The chromel-alumel thermocouple required for the test was welded into the metal test specimens and inserted into the ceramics. ANOVA and Tukey's test revealed significant differences (p=0.01 for the MCBS test results (MPa, with PI showing higher MCBS (67.72 than the other pairs, which did not present any significant differences. The CTE (10-6 oC-1 differences were: VBI (0.54, VBD (1.33, VB2I (-0.14, VB2D (0.63, PI (1.84 and PD (2.62. Pearson's correlation test (r=0.17 was performed to evaluate of correlation between MCBS and CTE differences. Within the limitations of this study and based on the obtained results, there was no correlation between MCBS and CTE differences for the evaluated metal-ceramic pairs.

  6. Interferometric measurement of the temperature coefficient of the refractive index dn/dT and the coefficient of thermal expansion of Pr:YLF laser crystals.

    Science.gov (United States)

    Kazasidis, Orestis S; Wittrock, Ulrich

    2014-12-15

    We report interferometric measurements of the temperature coefficient of the refractive index (dn/dT) and the coefficient of thermal expansion (α) of a praseodymium-doped yttrium lithium fluoride (Pr:YLF) crystal and of a fused silica reference sample. Our phase-resolved interferometric method yields a large number of data points and thus allows a precise measurement and a good error estimation. Furthermore, both dn/dT and α are obtained simultaneously from a single measurement which reduces errors that can occur in separate measurements. Over the temperature range from 20 °C to 80 °C, the value of dn/dT of Pr:YLF decreases from −5.2 × 10(−6)/K to −6.2 × 10(−6)/K for the ordinary refractive index and from −7.6 × 10(−6)/K to −8.6 × 10(−6)/K for the extraordinary refractive index. The coefficient of thermal expansion for the a-axis of Pr:YLF increases from 16.4 × 10(−6)/K to 17.8 × 10(−6)/K over the same temperature range.

  7. Using a Michelson Interferometer to Measure Coefficient of Thermal Expansion of Copper

    Science.gov (United States)

    Scholl, Ryan; Liby, Bruce W.

    2009-01-01

    When most materials are heated they expand. This concept is usually demonstrated using some type of mechanical measurement of the linear expansion of a metal rod. We have developed an alternative laboratory method for measuring thermal expansion by using a Michelson interferometer. Using the method presented, interference, interferometry, and the…

  8. Analysis of rail cooling strategies through numerical simulation with instant calculation of thermal expansion coefficient

    Directory of Open Access Journals (Sweden)

    Pernía-Espinoza, A.

    2010-08-01

    Full Text Available This article describes a new methodology to simulate the cooling process for an asymmetrical Ri60 grooved rail, designed for city tramways, in a more realistic manner than that conducted previously by other authors for long steel sections. The approach considers the phase transformation of the steel and the forced convection cooling. The process is modelled as an uncoupled thermo-mechanical problem. First, the rail’s temperature history is obtained from a computer fluid dynamic model and subsequently introduced in the finite element model, in order to model the stresses and displacements. This second stage involves the calculation of the thermal expansion coefficient, for each element and at each iteration. The calculation is made according to the continuous cooling transformation diagram. These results lead to the extremely reliable determination of residual stresses as proved by the comparison with experimental data obtained in the industrial plant. The methodology allows for an accurate study of two types of cooling strategies for the Ri60 and the selection of the more suitable one.

    En este artículo se describe una nueva metodología para simular el proceso de enfriamiento de un rail asimétrico Ri60, diseñado para tranvías, de una forma mucho más realista que lo realizado hasta ahora para perfiles largos de acero. La propuesta considera los efectos de la transformación de fases del acero y el enfriamiento por convección forzada. El proceso es simulado como un proceso termo-mecánico desacoplado. Primero, las curvas de enfriamiento del rail son obtenidas a partir de un modelo basado en dinámica de fluidos computacional y posteriormente introducidas en el modelo de elementos finitos para calcular las tensiones y desplazamientos. En esta segunda fase se calcula, para cada elemento finito y en cada iteración, el coeficiente de dilatación térmica lineal según el diagrama de curvas de enfriamiento continuo. Estos resultados

  9. End plate for e.g. solid oxide fuel cell stack, sets thermal expansion coefficient of material to predetermined value

    DEFF Research Database (Denmark)

    2011-01-01

    .05-0.3 mm. USE - End plate for solid oxide fuel cell stack (claimed). Can also be used in polymer electrolyte fuel cell stack and direct methanol fuel cell stack. ADVANTAGE - The robustness of the end plate is improved. The structure of the end plate is simplified. The risk of delamination of the stack......NOVELTY - The end plate is made of material whose thermal expansion coefficient is corresponding to that of material of a cell (103). The thermal expansion coefficient of material is 9asterisk10-6 K-1 to 14asterisk10-6 K11. The thickness of the end plate is within the range of 0.001-1 mm and 0...

  10. Influence of Chemical Composition on Phase Transformation Temperature and Thermal Expansion Coefficient of Hot Work Die Steel

    Institute of Scientific and Technical Information of China (English)

    XIE Hao-jie; WU Xiao-chun; MIN Yong-an

    2008-01-01

    On the basis of the uniform design method,six kinds of martensitie hot work die steels were designed.The phase transformation temperatures including Ac1,Ac3,and M,were measured by DIL805A quenching dilatometer.The influences of the main elements on phase transformation temperatures were analyzed by quadratic stepwise regression analysis,and three corresponding equations were obtained.These equations,in which the interactions of the elements were considered,showed more effectiveness than the traditional ones.In addition,the thermal expansion coefficients of these steels in annealed state and quenched state were also obtained during the tests.The influences of chemical composition and temperature on the thermal expansion coefficient were analyzed;the equations obtained Were verified by using several kinds of steels.The predicted values were in accordance with the results of the experiments.

  11. Dependence of Ionicity and Thermal Expansion Coefficient on Valence Electron Density in AIIBIVC2V Chalcopyrite Semiconductors

    Directory of Open Access Journals (Sweden)

    Amar BAHADUR

    2013-06-01

    Full Text Available A striking correlation has been found to exist between the free electron density parameter, average bond length, homoplar energy gap, heteropolar energy gap, ionicity and thermal expansion coefficient for AIIBIVC2V chalcopyrite semiconductors. The estimated values of these parameters are in good agreement with the available experimental values and theoretical findings. The electron density parameter data is the only one input data to estimate all above properties.

  12. Application of inverse models and XRD analysis to the determination of Ti-17 {beta}-phase coefficients of thermal expansion

    Energy Technology Data Exchange (ETDEWEB)

    Freour, S. [GeM, Institut de Recherche en Genie Civil et Mecanique (UMR CNRS 6183), Universite de Nantes, Ecole Centrale de Nantes, 37 Boulevard de l' Universite, BP 406, 44 602 Saint-Nazaire cedex (France)]. E-mail: freour@crttsn.univ-nantes.fr; Gloaguen, D. [GeM, Institut de Recherche en Genie Civil et Mecanique (UMR CNRS 6183), Universite de Nantes, Ecole Centrale de Nantes, 37 Boulevard de l' Universite, BP 406, 44 602 Saint-Nazaire cedex (France); Francois, M. [Laboratoire des Systemes Mecaniques et d' Ingenierie Simultanee (LASMIS FRE CNRS 2719), Universite de Technologie de Troyes, 12 Rue Marie Curie, BP 2060, 10010 Troyes (France); Guillen, R. [GeM, Institut de Recherche en Genie Civil et Mecanique (UMR CNRS 6183), Universite de Nantes, Ecole Centrale de Nantes, 37 Boulevard de l' Universite, BP 406, 44 602 Saint-Nazaire cedex (France)

    2006-04-15

    scope of this work is the determination of the coefficients of thermal expansion of the Ti-17 {beta}-phase. A rigorous inverse thermo-elastic self-consistent scale transition micro-mechanical model extended to multi-phase materials was used. The experimental data required for the application of the inverse method were obtained from both the available literature and especially dedicated X-ray diffraction lattice strain measurements performed on the studied ({alpha} + {beta}) two-phase titanium alloy.

  13. An Irreducible Form for the Asymptotic Expansion Coefficients of the Heat Kernel of Fermions

    Science.gov (United States)

    Yajima, S.; Fukuda, M.; Tokuo, S.; Kubota, S.-I.; Higashida, Y.; Kamo, Y.

    2008-09-01

    We consider the asymptotic coefficients of the heat kernel for a fermion of spin (1)/(2) interacting with all types of non-abelian boson fields, i.e. totally antisymmetric tensor fields, in even dimensional Riemannian space. The coefficients are decomposed by irreducible matrices which are the totally antisymmetric product of the γ-matrices. The form of the coefficients given in our method is useful to evaluate some fermionic anomalies.

  14. The effect of aeration conditions, characterized by the volumetric mass transfer coefficient K(L)a, on the fermentation kinetics of Bacillus thuringiensis kurstaki.

    Science.gov (United States)

    Mounsef, Jihane Rahbani; Salameh, Dominique; Louka, Nicolas; Brandam, Cedric; Lteif, Roger

    2015-09-20

    The aeration is a key factor for Bacillus thuringiensis growth, sporulation and δ-endotoxins production. The objective of our work was to study the effect of aeration on the fermentation kinetics of Bacillus thuringiensis kurstaki (Btk), cultivated in a cereal milling byproduct (CMB) mono-component medium, in order to improve the δ-endotoxins productivity. Aeration conditions were systematically characterized by the volumetric mass transfer coefficient KLa. In the 6% CMB culture medium, different values of the maximal specific oxygen uptake rate were obtained at different values of KLa. For KLa of 7.2 h(-1), the growth was inhibited and the sporulation was defective. There was a linear increase of the average specific growth rate and faster sporulation and liberation of spores and δ-endotoxins crystals when KLa was increased between 13.3 h(-1) and 65.5 h(-1). Similar kinetic was observed in cultures performed at KLa equal to 65.5 h(-1) and 106.2 h(-1). The highest toxins productivity of 96.1 mg L(-1) (h)-1 was obtained in the 9% CMB culture medium for KLa of 102 h(-1). It was possible to track the evolution of the bacterial cells between vegetative growth, sporulation and liberation of mature spores by following the variation of the CO2 percent in the effluent gas.

  15. Excellence of numerical differentiation method in calculating the coefficients of high temperature series expansion of the free energy and convergence problem of the expansion

    Energy Technology Data Exchange (ETDEWEB)

    Zhou, S., E-mail: chixiayzsq@yahoo.com [School of Physics and Electronics, Central South University, Changsha, Hunan 410083 (China); Solana, J. R. [Departamento de Física Aplicada, Universidad de Cantabria, 39005 Santander (Spain)

    2014-12-28

    In this paper, it is shown that the numerical differentiation method in performing the coupling parameter series expansion [S. Zhou, J. Chem. Phys. 125, 144518 (2006); AIP Adv. 1, 040703 (2011)] excels at calculating the coefficients a{sub i} of hard sphere high temperature series expansion (HS-HTSE) of the free energy. Both canonical ensemble and isothermal-isobaric ensemble Monte Carlo simulations for fluid interacting through a hard sphere attractive Yukawa (HSAY) potential with extremely short ranges and at very low temperatures are performed, and the resulting two sets of data of thermodynamic properties are in excellent agreement with each other, and well qualified to be used for assessing convergence of the HS-HTSE for the HSAY fluid. Results of valuation are that (i) by referring to the results of a hard sphere square well fluid [S. Zhou, J. Chem. Phys. 139, 124111 (2013)], it is found that existence of partial sum limit of the high temperature series expansion series and consistency between the limit value and the true solution depend on both the potential shapes and temperatures considered. (ii) For the extremely short range HSAY potential, the HS-HTSE coefficients a{sub i} falls rapidly with the order i, and the HS-HTSE converges from fourth order; however, it does not converge exactly to the true solution at reduced temperatures lower than 0.5, wherein difference between the partial sum limit of the HS-HTSE series and the simulation result tends to become more evident. Something worth mentioning is that before the convergence order is reached, the preceding truncation is always improved by the succeeding one, and the fourth- and higher-order truncations give the most dependable and qualitatively always correct thermodynamic results for the HSAY fluid even at low reduced temperatures to 0.25.

  16. Dilatometer setup for low coefficient of thermal expansion materials measurements in the 140 K-250 K temperature range

    Science.gov (United States)

    Spannagel, Ruven; Hamann, Ines; Sanjuan, Josep; Schuldt, Thilo; Gohlke, Martin; Johann, Ulrich; Weise, Dennis; Braxmaier, Claus

    2016-10-01

    Space applications demand light weight materials with excellent dimensional stability for telescopes, optical benches, optical resonators, etc. Glass-ceramics and composite materials can be tuned to reach very low coefficient of thermal expansion (CTE) at different temperatures. In order to determine such CTEs, very accurate setups are needed. Here we present a dilatometer that is able to measure the CTE of a large variety of materials in the temperature range of 140 K to 250 K. The dilatometer is based on a heterodyne interferometer with nanometer noise levels to measure the expansion of a sample when applying small amplitude controlled temperature signals. In this article, the CTE of a carbon fiber reinforced polymer sample has been determined with an accuracy in the 10-8 K-1 range.

  17. The effect of bromination of carbon fibers on the coefficient of thermal expansion of graphite fiber-epoxy composites

    Science.gov (United States)

    Jaworske, D. A.; Maciag, C.

    1987-01-01

    To examine the effect of bromination of carbon fibers on the coefficient of thermal expansion (CTE) of carbon fiber epoxy composites, several pristine and brominated carbon fiber-epoxy composite samples were subjected to thermomechanical analysis. The CTE's of these samples were measured in the uniaxial and transverse directions. The CTE was dominated by the fibers in the uniaxial direction, while it was dominated by the matrix in the transverse directions. Bromination had no effect on the CTE of any of the composites. In addition, the CTE of fiber tow was measured in the absence of a polymer matrix, using an extension probe. The results from this technique were inconclusive.

  18. Flow and linear coefficient of thermal expansion of four types of Base Plate waxes compared with ADA standard

    Directory of Open Access Journals (Sweden)

    Monzavi A

    2002-07-01

    Full Text Available Waxes have a lot of applications in dentistry. Such materials are of thermoplastic type that undergoes deformation in different temperatures. Two important properties of base plate waxes are flow and their coefficient of linear thermal expansion. Recently, different institutions, inside the country, produce dentistry waxes, while they have not been standardized. Consequently, consumers' dissatisfaction are observed. In this research, the two above- mentioned factors were compared between three kinds of Iranian waxes with Cavex that is foreign production, based on test number 24 of ADA. To measure the flow rate in the temperatures of 23, 37 and 45°c, Wilcoxon statistical analysis was used. The results showed that in 23°c, the flow rate of Cavex and Azardent waxes met ADA standards; however, it was not true for two others types. In 37°c, the flow of none of the waxes was standardized and in 45°c their flow was acceptable, moreover, thermal expansion coefficient, for Cavex and Azardent types, was based on ADA standard.

  19. Temperature dependence of density, thermal expansion coefficient and shear viscosity of supercooled glycerol as a reflection of its structure.

    Science.gov (United States)

    Blazhnov, Ivan V; Malomuzh, Nikolay P; Lishchuk, Sergey V

    2004-10-01

    The relationship of the microstructure of supercooled, highly viscous glycerol to the temperature dependence of its density, thermal expansion coefficient, and shear viscosity are discussed. The character of this temperature dependence at the transition from low viscosity state to the solid amorphous state (solidified state without nuclei) is described with help of function psi, which can be interpreted as the effective number of degrees of freedom responsible for the change of viscosity of glycerol over a broad range; these degrees of freedom are those related to the alpha-relaxation process. It is shown that the change in effective activation energy of the viscosity is completely determined by the parameter psi. The change in the shear viscosity of glycerol due to the influence of the solid-phase nuclei is considered. It is shown that the introduction of the parameter phi, equal to the specific volume occupied by the nuclei of the solid phase, together with psi provides a natural explanation of the temperature dependence of density and thermal expansion coefficients of glycerol in its liquid, solid amorphous, glassy, and crystal states. The peculiarities of the temperature dependence of phi(T) and psi(T) for glycerol and o-terphenyl are compared.

  20. Study of performance of high speed turning using the volumetric dimension coefficient of resultant cutting force; Estudio del rendimiento del torneado de alta velocidad utilizando el coeficiente de dimension volumetrica de la fuerza de corte resultante

    Energy Technology Data Exchange (ETDEWEB)

    Hernandez-Gonzalez, L. W.; Perez-Rodriguez, R.; Zambrano-Robledo, P. C.; Siller-Carrillo, H. R.; Toscano-Reyes, H.

    2013-07-01

    This work deals with the experimental study of the resultant cutting force evolution of two coating carbide and a cermet inserts, during the dry turning of AISI 1045 steel with 400, 500 and 600 m/min cutting speeds. A new criterion for machinability study, the coefficient of volumetric dimension of cutting force, it is introduced. The investigation showed a better performance of cermet for moderate and intermediate cutting speeds, while at high cutting speed and final machining time, the three layers coated carbide achieved the best result. The factorial analysis of variance demonstrated a significant effect of machining time on the coefficient of volumetric dimension of resultant cutting force, while the material insert factor and their interaction, for intermediate cutting speed was just significant. (Author)

  1. Asymptotic expansions of recursion coefficients of orthogonal polynomials with truncated exponential weights

    OpenAIRE

    Joung, Haewon

    2002-01-01

    Let $\\beta>0$ and $W_\\beta (x) = \\exp (-|x|^\\beta )$, $x \\in \\mathbb{R}$. For $c>0$, define $W_{\\beta, cn} (x) = W_\\beta (x)$ if $|x| \\leq c^{1/\\beta}\\,a_{2n}$ and $W_{\\beta, cn} (x) = 0$ if $|x| > c^{1/\\beta}\\,a_{2n}$, where $a_{2n}$ denotes Mhaskar-Rahmanov-Saff number for $W_\\beta$. Let $\\gamma_n (W_{\\beta, cn})$ be the leading coefficient of the $n$th orthonormal polynomial corresponding to $W_{\\beta, cn}$ and write $\\alpha_n(W_{\\beta, cn}) = \\gamma_{n-1}(W_{\\beta, cn})/...

  2. NEW TRUNCATED EXPANSION METHOD AND SOLITON-LIKE SOLUTION OF VARIABLE COEFFICIENT KdV-MKdV EQUATION WITH THREE ARBITRARY FUNCTIONS

    Institute of Scientific and Technical Information of China (English)

    张解放; 刘宇陆

    2003-01-01

    The truncated expansion method for finding explicit and exact soliton- like solution of variable coefficient nonlinear evolution equation was described. The crucial idea of the method was first the assumption that coefficients of the truncated expansion formal solution are functions of time satisfying a set of algebraic equations, and then a set of ordinary different equations of undetermined functions that can be easily integrated were obtained. The simplicity and effectiveness of the method by application to a general variable coefficient KdV-MKdV equation with three arbitrary functions of time is illustrated.

  3. Thermoacoustic Effects at a Solid-Fluid Boundary: The Role of a Second-Order Thermal Expansion Coefficient

    Science.gov (United States)

    Gopinath, Ashok

    1996-01-01

    Analytical and numerical studies are to be carried out to examine time-averaged thermal effects which are induced by the interaction of strong acoustic fields with a rigid boundary (thermoacoustic streaming). Also of interest is the significance of a second-order thermal expansion coefficient that emerges from this analysis. The model problem to be considered is that of a sphere that is acoustically levitated such that it is effectively isolated in a high-intensity standing acoustic field. The solution technique involves matched asymptotic analysis along with numerical solution of the boundary layer equations. The objective of this study is to predict the thermoacoustic streaming behavior and fully understand the role of the associated second-order thermodynamic modulus.

  4. Variable-coefficient discrete ((G{sup '})/G )-expansion method for nonlinear differential-difference equations

    Energy Technology Data Exchange (ETDEWEB)

    Tang, Bo [School of Science, Xi' an Jiaotong University, Xi' an 710049 (China); He, Yinnian, E-mail: heyn@mail.xjtu.edu.cn [School of Science, Xi' an Jiaotong University, Xi' an 710049 (China); Wei, Leilei; Wang, Shaoli [School of Science, Xi' an Jiaotong University, Xi' an 710049 (China)

    2011-09-05

    In this Letter, a variable-coefficient discrete ((G{sup '})/G )-expansion method is proposed to seek new and more general exact solutions of nonlinear differential-difference equations. Being concise and straightforward, this method is applied to the (2+1)-dimension Toda equation. As a result, many new and more general exact solutions are obtained including hyperbolic function solutions, trigonometric function solutions and rational solutions. It is shown that the proposed method provides a very effective and powerful mathematical tool for solving a great many nonlinear differential-difference equations in mathematical physics. -- Highlights: → We propose a novel method for non-linear differential-difference equations. → Some new exact traveling wave solutions of Toda equation are obtained. → Some solutions develop a singularity at a finite point. → It appears that these singular solutions will model the physical phenomena.

  5. A STUDY OF THE PROPERTIES OF CP: COEFFICIENT OF THERMAL EXPANSION, DECOMPOSITION KINETICS AND REACTION TO SPARK, FRICTION AND IMPACT

    Energy Technology Data Exchange (ETDEWEB)

    Weese, R K; Burnham, A K; Fontes, A T

    2005-03-30

    The properties of pentaamine (5-cyano-2H-tetrazolato-N2) cobalt (III) perchlorate (CP), which was first synthesized in 1968, continues to be of interest for predicting behavior in handling, shipping, aging, and thermal cook-off situations. We report coefficient of thermal expansion (CTE) values over four specific temperature ranges, decomposition kinetics using linear heating rates, and the reaction to three different types of stimuli: impact, spark, and friction. The CTE was measured using a Thermal Mechanical Analyzer (TMA) for samples that were uniaxially compressed at 10,000 psi and analyzed over a dynamic temperature range of -20 C to 70 C. Using differential scanning calorimetry, DSC, CP was decomposed at linear heating rates of 1, 3, and 7 C/min and the kinetic triplet calculated using the LLNL code Kinetics05. Values are also reported for spark, friction, and impact sensitivity.

  6. An Investigation of the Thermal Expansion Coefficient for Resin Concrete with ZrW2O8

    Directory of Open Access Journals (Sweden)

    Kuangzhe Lin

    2015-08-01

    Full Text Available This paper presents a novel resin concrete obtained by adding cubic zirconium tungstate (ZrW2O8 as filler. A prediction algorithm on the thermal expansion coefficient (CTE of resin concrete (including filler was established on the basis of the meso-mechanics method and a three-phase model for concrete. The concept of twice mixing was also proposed for prediction accuracy. Then, a 2D and 3D irregular polygon aggregate particles packing model was set up by Matlab and the properties of the packing model were simulated by finite element analysis. Finally, resin concrete samples were made and their CTE were measured. Mix proportion and addition of ZrW2O8 as influencing factors were considered in this experiment. The CTE of resin concrete was verified by comparing results of the prediction model, simulation model and experiment. The optimum CTE obtained from the experiment was 1.504 × 10−6/K. Compared with 6.817 × 10−6/K without ZrW2O8, it was found that the addition of ZrW2O8 to resin concrete can make it perform significantly better in thermal expansion.

  7. Compressibility, thermal expansion coefficient and heat capacity of CH4 and CO2 hydrate mixtures using molecular dynamics simulations.

    Science.gov (United States)

    Ning, F L; Glavatskiy, K; Ji, Z; Kjelstrup, S; H Vlugt, T J

    2015-01-28

    Understanding the thermal and mechanical properties of CH4 and CO2 hydrates is essential for the replacement of CH4 with CO2 in natural hydrate deposits as well as for CO2 sequestration and storage. In this work, we present isothermal compressibility, isobaric thermal expansion coefficient and specific heat capacity of fully occupied single-crystal sI-CH4 hydrates, CO2 hydrates and hydrates of their mixture using molecular dynamics simulations. Eight rigid/nonpolarisable water interaction models and three CH4 and CO2 interaction potentials were selected to examine the atomic interactions in the sI hydrate structure. The TIP4P/2005 water model combined with the DACNIS united-atom CH4 potential and TraPPE CO2 rigid potential were found to be suitable molecular interaction models. Using these molecular models, the results indicate that both the lattice parameters and the compressibility of the sI hydrates agree with those from experimental measurements. The calculated bulk modulus for any mixture ratio of CH4 and CO2 hydrates varies between 8.5 GPa and 10.4 GPa at 271.15 K between 10 and 100 MPa. The calculated thermal expansion and specific heat capacities of CH4 hydrates are also comparable with experimental values above approximately 260 K. The compressibility and expansion coefficient of guest gas mixture hydrates increase with an increasing ratio of CO2-to-CH4, while the bulk modulus and specific heat capacity exhibit the opposite trend. The presented results for the specific heat capacities of 2220-2699.0 J kg(-1) K(-1) for any mixture ratio of CH4 and CO2 hydrates are the first reported so far. These computational results provide a useful database for practical natural gas recovery from CH4 hydrates in deep oceans where CO2 is considered to replace CH4, as well as for phase equilibrium and mechanical stability of gas hydrate-bearing sediments. The computational schemes also provide an appropriate balance between computational accuracy and cost for predicting

  8. The relationship between bond ionicity, lattice energy, coefficient of thermal expansion and microwave dielectric properties of Nd(Nb(1-x)Sb(x))O4 ceramics.

    Science.gov (United States)

    Zhang, Ping; Zhao, Yonggui; Wang, Xiuyu

    2015-06-28

    The crystalline structure refinement, chemical bond ionicity, lattice energy and coefficient of thermal expansion were carried out for Nd(Nb(1-x)Sb(x))O4 ceramics with a monoclinic fergusonite structure to investigate the correlations between the crystalline structure, phase stability, bond ionicity, lattice energy, coefficient of thermal expansion, and microwave dielectric properties. The bond ionicity, lattice energy, and coefficient of thermal expansion of Nd(Nb(1-x)Sb(x))O4 ceramics were calculated using a semiempirical method based on the complex bond theory. The phase structure stability varied with the lattice energy which was resulted by the substitution constant of Sb(5+). With the increasing of the Sb(5+) contents, the decrease of Nb/Sb-O bond ionicity was observed, which could be contributed to the electric polarization. The ε(r) had a close relationship with the Nb/Sb-O bond ionicity. The increase of the Q×f and |τ(f)| values could be attributed to the lattice energy and the coefficient of thermal expansion. The microwave dielectric properties of Nd(Nb(1-x)Sb(x))O4 ceramics with the monoclinic fergusonite structure were strongly dependent on the chemical bond ionicity, lattice energy and coefficient of thermal expansion.

  9. Numerical investigation of multi-beam laser heterodyne measurement with ultra-precision for linear expansion coefficient of metal based on oscillating mirror modulation

    Institute of Scientific and Technical Information of China (English)

    Li Yan-Chao; Wang Chun-Hui; Qu Yang; Gao Long; Cong Hai-Fang; Yang Yan-Ling; Gao Jie; Wang Ao-You

    2011-01-01

    This paper proposes a novel method of multi-beam laser heterodyne measurement for metal linear expansion coefficient. Based on the Doppler effect and heterodyne technology, the information is loaded of length variation to the frequency difference of the multi-beam laser heterodyne signal by the frequency modulation of the oscillating mirror,this method can obtain many values of length variation caused by temperature variation after the multi-beam laser heterodyne signal demodulation simultaneously. Processing these values by weighted-average, it can obtain length variation accurately, and eventually obtain the value of linear expansion coefficient of metal by the calculation. This novel method is used to simulate measurement for linear expansion coefficient of metal rod under different temperatures by MATLAB, the obtained result shows that the relative measurement error of this method is just 0.4%.

  10. Polynomial Chaos Expansion of Random Coefficients and the Solution of Stochastic Partial Differential Equations in the Tensor Train Format

    KAUST Repository

    Dolgov, Sergey

    2015-11-03

    We apply the tensor train (TT) decomposition to construct the tensor product polynomial chaos expansion (PCE) of a random field, to solve the stochastic elliptic diffusion PDE with the stochastic Galerkin discretization, and to compute some quantities of interest (mean, variance, and exceedance probabilities). We assume that the random diffusion coefficient is given as a smooth transformation of a Gaussian random field. In this case, the PCE is delivered by a complicated formula, which lacks an analytic TT representation. To construct its TT approximation numerically, we develop the new block TT cross algorithm, a method that computes the whole TT decomposition from a few evaluations of the PCE formula. The new method is conceptually similar to the adaptive cross approximation in the TT format but is more efficient when several tensors must be stored in the same TT representation, which is the case for the PCE. In addition, we demonstrate how to assemble the stochastic Galerkin matrix and to compute the solution of the elliptic equation and its postprocessing, staying in the TT format. We compare our technique with the traditional sparse polynomial chaos and the Monte Carlo approaches. In the tensor product polynomial chaos, the polynomial degree is bounded for each random variable independently. This provides higher accuracy than the sparse polynomial set or the Monte Carlo method, but the cardinality of the tensor product set grows exponentially with the number of random variables. However, when the PCE coefficients are implicitly approximated in the TT format, the computations with the full tensor product polynomial set become possible. In the numerical experiments, we confirm that the new methodology is competitive in a wide range of parameters, especially where high accuracy and high polynomial degrees are required.

  11. Polynomial Chaos Expansion of Random Coefficients and the Solution of Stochastic Partial Differential Equations in the Tensor Train Format

    KAUST Repository

    Dolgov, Sergey

    2015-11-03

    We apply the tensor train (TT) decomposition to construct the tensor product polynomial chaos expansion (PCE) of a random field, to solve the stochastic elliptic diffusion PDE with the stochastic Galerkin discretization, and to compute some quantities of interest (mean, variance, and exceedance probabilities). We assume that the random diffusion coefficient is given as a smooth transformation of a Gaussian random field. In this case, the PCE is delivered by a complicated formula, which lacks an analytic TT representation. To construct its TT approximation numerically, we develop the new block TT cross algorithm, a method that computes the whole TT decomposition from a few evaluations of the PCE formula. The new method is conceptually similar to the adaptive cross approximation in the TT format but is more efficient when several tensors must be stored in the same TT representation, which is the case for the PCE. In addition, we demonstrate how to assemble the stochastic Galerkin matrix and to compute the solution of the elliptic equation and its postprocessing, staying in the TT format. We compare our technique with the traditional sparse polynomial chaos and the Monte Carlo approaches. In the tensor product polynomial chaos, the polynomial degree is bounded for each random variable independently. This provides higher accuracy than the sparse polynomial set or the Monte Carlo method, but the cardinality of the tensor product set grows exponentially with the number of random variables. However, when the PCE coefficients are implicitly approximated in the TT format, the computations with the full tensor product polynomial set become possible. In the numerical experiments, we confirm that the new methodology is competitive in a wide range of parameters, especially where high accuracy and high polynomial degrees are required.

  12. A novel implementation algorithm of asymptotic homogenization for predicting the effective coefficient of thermal expansion of periodic composite materials

    Science.gov (United States)

    Zhang, Yongcun; Shang, Shipeng; Liu, Shutian

    2017-01-01

    Asymptotic homogenization (AH) is a general method for predicting the effective coefficient of thermal expansion (CTE) of periodic composites. It has a rigorous mathematical foundation and can give an accurate solution if the macrostructure is large enough to comprise an infinite number of unit cells. In this paper, a novel implementation algorithm of asymptotic homogenization (NIAH) is developed to calculate the effective CTE of periodic composite materials. Compared with the previous implementation of AH, there are two obvious advantages. One is its implementation as simple as representative volume element (RVE). The new algorithm can be executed easily using commercial finite element analysis (FEA) software as a black box. The detailed process of the new implementation of AH has been provided. The other is that NIAH can simultaneously use more than one element type to discretize a unit cell, which can save much computational cost in predicting the CTE of a complex structure. Several examples are carried out to demonstrate the effectiveness of the new implementation. This work is expected to greatly promote the widespread use of AH in predicting the CTE of periodic composite materials.

  13. Spatial variability in the coefficient of thermal expansion induces pre-service stresses in computer models of virgin Gilsocarbon bricks

    Science.gov (United States)

    Arregui-Mena, José David; Margetts, Lee; Griffiths, D. V.; Lever, Louise; Hall, Graham; Mummery, Paul M.

    2015-10-01

    In this paper, the authors test the hypothesis that tiny spatial variations in material properties may lead to significant pre-service stresses in virgin graphite bricks. To do this, they have customised ParaFEM, an open source parallel finite element package, adding support for stochastic thermo-mechanical analysis using the Monte Carlo Simulation method. For an Advanced Gas-cooled Reactor brick, three heating cases have been examined: a uniform temperature change; a uniform temperature gradient applied through the thickness of the brick and a simulated temperature profile from an operating reactor. Results are compared for mean and stochastic properties. These show that, for the proof-of-concept analyses carried out, the pre-service von Mises stress is around twenty times higher when spatial variability of material properties is introduced. The paper demonstrates that thermal gradients coupled with material incompatibilities may be important in the generation of stress in nuclear graphite reactor bricks. Tiny spatial variations in coefficient of thermal expansion (CTE) and Young's modulus can lead to the presence of thermal stresses in bricks that are free to expand.

  14. The first three coefficients in the high temperature series expansion of free energy for simple potential models with hard-sphere cores and continuous tails.

    Science.gov (United States)

    Zhou, Shiqi; Solana, J R

    2013-08-08

    The first three coefficients of the high temperature series expansion (HTSE) of the Helmholtz free energy for a number of simple potential models with hard-sphere cores plus continuous tails are obtained for the first time from Monte Carlo simulations. The potential models considered include Square-well, Sutherland, attractive Yukawa, and triangle-well with different potential ranges, as well as a model potential qualitatively resembling the depletion potential in colloidal dispersions. The simulation data are used to evaluate performance of a recent coupling parameter series expansion (CPSE) in calculating for these coefficients, and a traditional macroscopic compressibility approximation (MCA) for the second-order coefficient only. A comprehensive comparison based on these coefficients from the two theoretical approaches and simulations enables one to conclude that (i) unlike one common experience that the widely used MCA usually underestimates the second-order coefficient, the MCA can both overestimate and underestimate the second-order coefficient, and worsens as the range of the potential decreases; and (ii) in contrast, the CPSE not only reproduce the trends in the density dependence of the perturbation coefficients, even the third one, observed in the simulations, but also the agreement is quantitative in most cases, and this clearly highlights the potential of the CPSE in providing accurate estimations for the higher-order coefficients, thus giving rise to an accurate higher-order HTSE.

  15. The Heat Resistance of Microbial Cells Represented by D Values Can be Estimated by the Transition Temperature and the Coefficient of Linear Expansion.

    Science.gov (United States)

    Nakanishi, Koichi; Kogure, Akinori; Deuchi, Keiji; Kuwana, Ritsuko; Takamatsu, Hiromu; Ito, Kiyoshi

    2015-01-01

    We previously developed a method for evaluating the heat resistance of microorganisms by measuring the transition temperature at which the coefficient of linear expansion of a cell changes. Here, we performed heat resistance measurements using a scanning probe microscope with a nano thermal analysis system. The microorganisms studied included six strains of the genus Bacillus or related genera, one strain each of the thermophilic obligate anaerobic bacterial genera Thermoanaerobacter and Moorella, two strains of heat-resistant mold, two strains of non-sporulating bacteria, and one strain of yeast. Both vegetative cells and spores were evaluated. The transition temperature at which the coefficient of linear expansion due to heating changed from a positive value to a negative value correlated strongly with the heat resistance of the microorganism as estimated from the D value. The microorganisms with greater heat resistance exhibited higher transition temperatures. There was also a strong negative correlation between the coefficient of linear expansion and heat resistance in bacteria and yeast, such that microorganisms with greater heat resistance showed lower coefficients of linear expansion. These findings suggest that our method could be useful for evaluating the heat resistance of microorganisms.

  16. Large pyroelectric and thermal expansion coefficients in the [(CH3)2NH2]Mn (HCOO)3 metal-organic framework

    Science.gov (United States)

    Ma, Yinina; Cong, Junzhuang; Chai, Yisheng; Yan, Liqin; Shang, Dashan; Sun, Young

    2017-07-01

    The [(CH3)2NH2]Mn(HCOO)3 perovskite metal-organic framework exhibits a first-order ferroelectric phase transition with a high polarization at Tc ˜ 192 K, induced by the order-disorder transition of hydrogen bonds. Accompanying this sharp phase transition, a huge pyroelectric coefficient with a peak value of 5.16 × 10-2 C/m2 K is detected. In addition, there is a large lattice expansion along the [012] direction at Tc, resulting in a giant linear thermal expansion coefficient as high as 35 000 ppm/K. These striking results indicate that ferroelectric metal-organic frameworks combing both merits of inorganic and organic compounds hold a great potential in generating superior pyroelectric and thermal expansion properties.

  17. Effect of colouring green stage zirconia on the adhesion of veneering ceramics with different thermal expansion coefficients.

    Science.gov (United States)

    Aktas, Guliz; Sahin, Erdal; Vallittu, Pekka; Ozcan, Mutlu; Lassila, Lippo

    2013-12-01

    This study evaluated the adhesion of zirconia core ceramics with their corresponding veneering ceramics, having different thermal expansion coefficients (TECs), when zirconia ceramics were coloured at green stage. Zirconia blocks (N=240; 6 mm×7 mm×7 mm) were manufactured from two materials namely, ICE Zirconia (Group 1) and Prettau Zirconia (Group 2). In their green stage, they were randomly divided into two groups. Half of the specimens were coloured with colouring liquid (shade A2). Three different veneering ceramics with different TEC (ICE Ceramic, GC Initial Zr and IPS e.max Ceram) were fired on both coloured and non-coloured zirconia cores. Specimens of high noble alloys (Esteticor Plus) veneered with ceramic (VM 13) (n=16) acted as the control group. Core-veneer interface of the specimens were subjected to shear force in the Universal Testing Machine (0.5 mm⋅min(-1)). Neither the zirconia core material (P=0.318) nor colouring (P=0.188) significantly affected the results (three-way analysis of variance, Tukey's test). But the results were significantly affected by the veneering ceramic (P=0.000). Control group exhibited significantly higher mean bond strength values (45.7±8) MPa than all other tested groups ((27.1±4.1)-(39.7±4.7) and (27.4±5.6)-(35.9±4.7) MPa with and without colouring, respectively) (Pceramic covering ceramic group, veneering ceramic was left adhered >1/3 of the metal surface. Colouring zirconia did not impair adhesion of veneering ceramic, but veneering ceramic had a significant influence on the core-veneer adhesion. Metal-ceramic adhesion was more reliable than all zirconia-veneer ceramics tested.

  18. Direct calculation of the linear thermal expansion coefficients of MoS2 via symmetry-preserving deformations

    Science.gov (United States)

    Gan, Chee Kwan; Liu, Yu Yang Fredrik

    2016-10-01

    Using density-functional perturbation theory and the Grüneisen formalism, we directly calculate the linear thermal expansion coefficients (TECs) of a hexagonal bulk system MoS2 in the crystallographic a and c directions. The TEC calculation depends critically on the evaluation of a temperature-dependent quantity Ii(T ) , which is the integral of the product of heat capacity and Γi(ν ) , of frequency ν and strain type i , where Γi(ν ) is the phonon density of states weighted by the Grüneisen parameters. We show that to determine the linear TECs we may use minimally two uniaxial strains in the z direction and either the x or y direction. However, a uniaxial strain in either the x or y direction drastically reduces the symmetry of the crystal from a hexagonal one to a base-centered orthorhombic one. We propose to use an efficient and accurate symmetry-preserving biaxial strain in the x y plane to derive the same result for Γ (ν ) . We highlight that the Grüneisen parameter associated with a biaxial strain may not be the same as the average of Grüneisen parameters associated with two separate uniaxial strains in the x and y directions due to possible preservation of degeneracies of the phonon modes under a biaxial deformation. Large anisotropy of TECs is observed where the linear TEC in the c direction is about 1.8 times larger than that in the a or b direction at high temperatures. Our theoretical TEC results are compared with experiment. The symmetry-preserving approach adopted here may be applied to a broad class of two lattice-parameter systems such as hexagonal, trigonal, and tetragonal systems, which allows many complicated systems to be treated on a first-principles level.

  19. Effect of colouring green stage zirconia on the adhesion of veneering ceramics with different thermal expansion coefficients

    Institute of Scientific and Technical Information of China (English)

    Guliz Aktas; Erdal Sahin; Pekka Vallittu; Mutlu Ozcan; Lippo Lassila

    2013-01-01

    This study evaluated the adhesion of zirconia core ceramics with their corresponding veneering ceramics, having different thermal expansion coefficients (TECs), when zirconia ceramics were coloured at green stage. Zirconia blocks (N5240;6 mm37 mm37 mm) were manufactured from two materials namely, ICE Zirconia (Group 1) and Prettau Zirconia (Group 2). In their green stage, they were randomly divided into two groups. Half of the specimens were coloured with colouring liquid (shade A2). Three different veneering ceramics with different TEC (ICE Ceramic, GC Initial Zr and IPS e.max Ceram) were fired on both coloured and non-coloured zirconia cores. Specimens of high noble alloys (Esteticor Plus) veneered with ceramic (VM 13) (n516) acted as the control group. Core-veneer interface of the specimens were subjected to shear force in the Universal Testing Machine (0.5 mm?min21). Neither the zirconia core material (P50.318) nor colouring (P50.188) significantly affected the results (three-way analysis of variance, Tukey’s test). But the results were significantly affected by the veneering ceramic (P50.000). Control group exhibited significantly higher mean bond strength values (45.768) MPa than all other tested groups ((27.164.1)2(39.764.7) and (27.465.6)2(35.964.7) MPa with and without colouring, respectively) (P,0.001). While in zirconia-veneer test groups, predominantly mixed type of failures were observed with the veneering ceramic covering ,1/3 of the substrate surface, in the metal-ceramic group, veneering ceramic was left adhered .1/3 of the metal surface. Colouring zirconia did not impair adhesion of veneering ceramic, but veneering ceramic had a significant influence on the core-veneer adhesion. Metal-ceramic adhesion was more reliable than all zirconia-veneer ceramics tested.

  20. 基础养老保险缴费率膨胀系数研究%A STUDY OF EXPANSION COEFFICIENT OF ENDOWMENT INSURANCE PAYMENT RATE

    Institute of Scientific and Technical Information of China (English)

    穆怀中; 陈洋; 陈曦

    2015-01-01

    围绕国家提出降低养老保险缴费率的宗旨,本文研究适度降低基础养老保险缴费率的路径,提出养老保险缴费率膨胀系数概念和定量研究数理模型。本文提出,社会保障体制转轨的“成本叠加”、全社会代际交叠的“有限责任”、个人生命周期的“不可预期”是导致养老保险缴费率膨胀的主要原因和内在规律。定量研究发现,现存养老保险缴费率膨胀系数为9.44%,其中覆盖面膨胀系数为5.59%,遵缴率膨胀系数为3.69%,提前退休膨胀系数为0.16%。纵向回归研究发现,覆盖面的膨胀系数弹性为-0.15,遵缴率的膨胀系数弹性为-0.2,提前退休的膨胀系数弹性为0.938。在此基础上,本文提出了相关建议。%In order to reduce the endowment insurance payment rate and moderately reduce the urban employee basic pension payment rate,this paper put forward the concept of endowment insurance payment rate expansion coefficient and set up quantitative mathematical model.This paper concluded the superposi-tion cost of social security system in transition,the limited liability of intergenerational overlapping in the whole society and the unpredictable of personal life cycle were the main reasons and internal rules of en-dowment insurance payment rate’ s expansion.Quantitative study found that the current expansion coeffi-cient of endowment insurance payment rate was 9. 44%and the coverage expansion coefficient was 5. 5 9%, the rate of payment according to system requirements expansion coefficient was 3. 6 9%and the early retire-ment expansion coefficient was 0. 1 6%.Longitudinal regression analysis showed that the coverage expan-sion coefficient elasticity was -0. 1 5 ,the rate of payment according to system requirements expansion co-efficient elasticity was -0. 2,the early retirement expansion coefficient elasticity was 0. 938.Some policy suggestions were provided.

  1. Influence of sodalite zeolite infiltration on the coefficient of thermal expansion and bond strength of all-ceramic dental prostheses.

    Science.gov (United States)

    Naji, Ghassan Abdul-Hamid; Omar, Ros Anita; Yahya, Rosiyah

    2017-03-01

    In all-ceramic systems, a high incidence of veneer chip-off has been reported in clinical studies. Coefficient of thermal expansion (CTE) behaviour is one of the factors that may increase residual stress in the interface and influence the veneer/core bond strength. Therefore, this study aimed to evaluate the effect of sodalite zeolite-infiltration on the CTE behaviour and bond strength of different all-ceramic prostheses. The case-study groups were synthesized sodalite zeolite-infiltrated alumina (IA-SOD) and synthesized sodalite zeolite-infiltrated zirconia-toughened alumina (ZTA) (IZ-SOD), while the control groups were glass-infiltrated alumina (IA-glass) and glass-infiltrated ZTA (IZ-glass). Forty cylindrical-shaped samples measuring 5 mm in diameter and 10 mm in height were tested for CTE using a thermo-mechanical analyser machine, and forty disc-shaped ceramic samples measuring 12 mm in diameter and 1.2 ± 0.2 mm in thickness were prepared using specially designed stainless steel split mould and veneered by cylinder-shaped (2 mm high × 2 mm diameter) low-fusing porcelain (Vita VM7). The veneer/core samples were sintered and tested for shear bond strength using a high precision universal testing machine. Scanning electron microscope, stereo microscope, atomic force microscope, and energy-dispersive X-ray spectroscopy were used to investigate the structural characteristics of samples at the fracture surface. The collected data were analyzed with a one-way ANOVA and Tukey HSD test (α=.05). IZ-SOD revealed highest CTE and shear bond strength values, while the IA-glass revealed the lowest values than the other groups. There was no significant difference in CTE and bond strength among IZ-SOD, IA-SOD and IZ-glass samples (p>0.05). The experimental SOD zeolite-infiltrated samples revealed higher CTE mismatch and bond strength along with a more favourable mode of failure than did the commercial glass-infiltrated samples. Sandblast technique is considered as effective

  2. Effect of porosity on the thermal expansion coefficient: A discussion on the paper ‘Effects of mineral admixtures on the thermal expansion properties of hardened cement paste' by Z.H. Shui, R. Zhang, W. Chen, D. Xuan, Constr. Build. Mater. 24(9) (2010) 1761–1767

    OpenAIRE

    Ghabezloo, Siavash

    2010-01-01

    A discussion is presented on the effect of porosity change on the thermal expansion coefficient of porous materials. It is shown that both drained and undrained thermal expansion coefficients normally increase with porosity increase. Consequently the reduction of the thermal expansion coefficient with the porosity increase, as obtained in the experimental results of Shui et al. (Constr. Build. Mater. (2010), 24(9), 1761-1767), can not be considered as a general trend for the behaviour of poro...

  3. Determination of Thermal Expansion Coefficients and Locating the Temperature-Induced Phase Transition in Methylammonium Lead Perovskites Using X-ray Diffraction.

    Science.gov (United States)

    Jacobsson, T Jesper; Schwan, L Josef; Ottosson, Mikael; Hagfeldt, Anders; Edvinsson, Tomas

    2015-11-16

    Lead halogen perovskites, and particularly methylammonium lead iodine, CH3NH3PbI3, have recently attracted considerable interest as alternative solar cell materials, and record solar cell efficiencies have now surpassed 20%. Concerns have, however, been raised about the thermal stability of methylammonium lead iodine, and a phase transformation from a tetragonal to a cubic phase has been reported at elevated temperature. Here, this phase transition has been investigated in detail using temperature-dependent X-ray diffraction measurements. The phase transformation is pinpointed to 54 °C, which is well within the normal operating range of a typical solar cell. The cell parameters were extracted as a function of the temperature, from which the thermal expansion coefficient was calculated. The latter was found to be rather high (αv = 1.57 × 10(-4) K(-1)) for both the tetragonal and cubic phases. This is 6 times higher than the thermal expansion coefficient for soda lime glass and CIGS and 11 times larger than that of CdTe. This could potentially be of importance for the mechanical stability of perovskite solar cells in the temperature cycling experienced under normal day-night operation. The experimental knowledge of the thermal expansion coefficients and precise determination of the cell parameters can potentially also be valuable while conducting density functional theory simulations on these systems in order to deliver more accurate band structure calculations.

  4. Research Progress of Lowing Thermal Expansion Coefficient of Thermoplastic Plastics%降低热塑性塑料热膨胀系数的研究进展

    Institute of Scientific and Technical Information of China (English)

    吴银财; 郑嘉玮; 宁冲冲; 崔益华

    2012-01-01

    综述了国内外关于降低热塑性塑料热膨胀系数的主要方法,按添加物的种类分为:一般颗粒材料填充改性、空心玻璃微珠填充改性、负热膨胀系数材料填充改性、稀土氧化物填充改性、高热稳定性材料填充改性、橡胶共混改性、多种材料混杂复合改性等.对未来降低热塑性塑料热膨胀系数的发展方向进行了展望.%Main methods of lowing the thermal expansion coefficient of thermoplastic plastics at home and abroad were summarized. According to the types of additives the methods could be divided into the following categories : general granular materials filling modification, hollow glass bead filling modification, materials with negative thermal expansion coefficient filling modification, rare earth oxide filling modification, high thermal stability materials filling modification, rubber blending modification, a variety of materials hybrid mixing modification and so on. The future development trend of lowing the thermal expansion coefficeint of thermoplastic plastics was prospected.

  5. Determination of the linear coefficient of thermal expansion in polymer films at the nanoscale: influence of the composition of EVA copolymers and the molecular weight of PMMA.

    Science.gov (United States)

    González-Benito, J; Castillo, E; Cruz-Caldito, J F

    2015-07-28

    Nanothermal-expansion of poly(ethylene-co-vinylacetate), EVA, and poly(methyl methacrylate), PMMA, in the form of films was measured to finally obtain linear coefficients of thermal expansion, CTEs. The simple deflection of a cantilever in an atomic force microscope, AFM, was used to monitor thermal expansions at the nanoscale. The influences of: (a) the structure of EVA in terms of its composition (vinylacetate content) and (b) the size of PMMA chains in terms of the molecular weight were studied. To carry out this, several polymer samples were used, EVA copolymers with different weight percents of the vinylacetate comonomer (12, 18, 25 and 40%) and PMMA polymers with different weight average molecular weights (33.9, 64.8, 75.600 and 360.0 kg mol(-1)). The dependencies of the vinyl acetate weight fraction of EVA and the molecular weight of PMMA on their corresponding CTEs were analyzed to finally explain them using new, intuitive and very simple models based on the rule of mixtures. In the case of EVA copolymers a simple equation considering the weighted contributions of each comonomer was enough to estimate the final CTE above the glass transition temperature. On the other hand, when the molecular weight dependence is considered the free volume concept was used as novelty. The expansion of PMMA, at least at the nanoscale, was well and easily described by the sum of the weighted contributions of the occupied and free volumes, respectively.

  6. Predictions of thermal expansion coefficients of rare-earth zirconate pyrochlores: A quasi-harmonic approximation based on stable phonon modes

    Science.gov (United States)

    Lan, Guoqiang; Ouyang, Bin; Xu, Yushuai; Song, Jun; Jiang, Yong

    2016-06-01

    Rare-earth (RE) pyrochlores are considered as promising candidate materials for the thermal barrier coating. In this study, we performed first-principles calculations, augmented by quasi-harmonic phonon calculations, to investigate the thermal expansion behaviors of several RE2Zr2O7 (RE = La, Nd, Sm, Gd) pyrochlores. Our findings show that RE2Zr2O7 pyrochlores exhibit low-lying optical phonon frequencies that correspond to RE-cation rattling vibrational modes. These frequencies become imaginary upon volume expansion, preventing correct determination of the free energy versus volume relation and thereby quantification of thermal expansion using QH phonon calculations. To address this challenge, we proposed a QH approximation approach based on stable phonon modes where the RE-cation rattling modes were systematically eliminated. This approach is shown to provide accurate predictions of the coefficients of thermal expansion (CTEs) of RE2Zr2O7 pyrochlores, in good agreement with experimental measurements and data from first-principles molecular dynamics simulations. In addition, we showed that the QH Debye model considerably overestimates the magnitudes and wrongly predicts the trend for the CTEs of RE2Zr2O7 pyrochlores.

  7. Thermally induced changes in the focal distance of composite mirrors - Composites with a zero coefficient of thermal expansion of the radius of curvature

    Science.gov (United States)

    Dolgin, Benjamin P.

    1992-01-01

    Calculations are presented of the coefficient of thermal expansion (CTE) of the radius of curvature of the reflector face sheets made of a quasi-isotropic composite. It is shown that, upon cooling, the change of the CTE of the focal distance of the mirror is equal to that of the radius of the curvature of the reflector face sheet. The CTE of the radius of the curvature of a quasi-isotropic composite face sheet depends on both the in-plane and the out-of-plane CTEs. The zero in-plane CTE of a face sheet does not guarantee mirrors with no focal length changes.

  8. A Novel SOFC/SOEC Sealing Glass with a Low SiO2 Content and a High Thermal Expansion Coefficient  

    DEFF Research Database (Denmark)

    Kiebach, Wolff-Ragnar; Agersted, Karsten; Zielke, Philipp

    2017-01-01

    phase boundaries. To reduce the amount of Si emission, a low Si containing sealing glass (chemical composition: 48 mol% CaO, 19 mol% ZnO, 21 mol% B2O3 and 12 mol% SiO2) was developed at DTU. In this presentation, the results from thermal characterization, like thermal expansion coefficient, glass......Solid oxide cells require seals that can function in harsh, elevated temperature environments. In the case of solid oxide electrolysis (SOEC), also a low Si content is desired, since Si impurities from the glass sealing can be transported to the active fuel electrode and poison the Ni-YSZ triple...

  9. Effect of surface tension and coefficient of thermal expansion in 30 nm scale nanoimprinting with two flexible polymer molds.

    Science.gov (United States)

    Kim, Jae Kwan; Cho, Hye Sung; Jung, Ho-Sup; Lim, Kipil; Kim, Ki-Bum; Choi, Dae-Geun; Jeong, Jun-Ho; Suh, Kahp-Yang

    2012-06-15

    We report on nanoimprinting of polymer thin films at 30 nm scale resolution using two types of ultraviolet (UV)-curable, flexible polymer molds: perfluoropolyether (PFPE) and polyurethane acrylate (PUA). It was found that the quality of nanopatterning at the 30 nm scale is largely determined by the combined effects of surface tension and the coefficient of thermal expansion of the polymer mold. In particular, the polar component of surface tension may play a critical role in clean release of the mold, as evidenced by much reduced delamination or broken structures for the less polarized PFPE mold when patterning a relatively hydrophilic PMMA film. In contrast, such problems were not notably observed with a relatively hydrophobic PS film for both polymer molds. In addition, the demolding characteristic was also influenced by the coefficient of thermal expansion so that no delamination or uniformity problems were observed when patterning a UV-curable polymer film at room temperature. These results suggest that a proper polymeric mold material needs to be chosen for patterning polymer films under different surface properties and processing conditions, providing insights into how a clean demolding characteristic can be obtained at 30 nm scale nanopatterning.

  10. Volumetric properties of human islet amyloid polypeptide in liquid water.

    Science.gov (United States)

    Brovchenko, I; Andrews, M N; Oleinikova, A

    2010-04-28

    The volumetric properties of human islet amyloid polypeptide (hIAPP) in water were studied in a wide temperature range by computer simulations. The intrinsic density rho(p) and the intrinsic thermal expansion coefficient alpha(p) of hIAPP were evaluated by taking into account the difference between the volumetric properties of hydration and bulk water. The density of hydration water rho(h) was found to decrease almost linearly with temperature upon heating and its thermal expansion coefficient was found to be notably higher than that of bulk water. The peptide surface exposed to water is more hydrophobic and its rho(h) is smaller in conformation with a larger number of intrapeptide hydrogen bonds. The two hIAPP peptides studied (with and without disulfide bridge) show negative alpha(p), which is close to zero at 250 K and decreases to approximately -1.5 x 10(-3) K(-1) upon heating to 450 K. The analysis of various structural properties of peptides shows a correlation between the intrinsic peptide volumes and the number of intrapeptide hydrogen bonds. The obtained negative values of alpha(p) can be attributed to the shrinkage of the inner voids of the peptides upon heating.

  11. 基于膨胀系数的正则表达式分组算法%Regular Expression Grouping Algorithm Based on Expansion Coefficient

    Institute of Scientific and Technical Information of China (English)

    王美阳; 唐学文; 杨正益

    2014-01-01

    确定性有限自动机( Deterministic Finite Automata , DFA)匹配速度远快于非确定性有限状态自动机( Non-determinis-tic Finite state Automata , NFA),但大量正则表达式转换为DFA时会引起状态爆炸而占用巨大的存储空间。首先定义膨胀系数( Expansion Coefficient , EC)来描述正则表达式的膨胀特性,然后在膨胀系数这一概念基础上,提出一种高效的分组算法---IGA( Improved Grouping Algorithm )算法对正则表达式进行有效分组,将容易引起状态爆炸的正则表达式相互隔离,从而节省存储空间。实验结果表明,与原有算法相比,在相同分组数目时IGA算法平均能够减少25%的状态数。%Matching speed of deterministic finite automata ( DFA) is far faster than that of the non-deterministic finite state au-tomata ( NFA) .However , when a large number of regular expressions transform into a DFA , the DFA may consume huge storage space because of state explosion .Firstly, to describe characteristics of the regular expressions , expansion coefficient was defined . Based on the concept of expansion coefficient , a more efficient grouping algorithm which named IGA algorithm was proposed .IGA algorithm isolated those regular expressions which easily lead to state explosion , thus saved storage space .Experimental results show that, compared with the original algorithm , when the number of groups is same to the original one , IGA algorithm could re-duce 25 percents of the number of states averagely .

  12. Real time investigation of the effect of thermal expansion coefficient mismatch on film-substrate strain partitioning in Ag/Si systems

    Science.gov (United States)

    Das, Debolina; Banu, Nasrin; Bisi, Bhaskar; Mahato, J. C.; Srihari, V.; Halder, Rumu; Dev, B. N.

    2016-10-01

    We have used X-ray diffraction (XRD) to investigate strain partitioning between an epitaxial layer and the substrate as a function of temperature, where the substrate (Si) and the epilayer material (Ag) have large thermal expansion coefficient (α) mismatch. The Ag/Si(111) system undergoes morphological changes upon heating, and the larger and taller islands are formed exposing more substrate surfaces. Sample heating was carried out under nitrogen flow. At >300 °C, the Si(111) diffraction peak splits into three. One of these components conforms to the thermal expansion of bulk Si. The other two components correspond to a highly nonlinear decrease and increase of Si-d(111) planar spacing. The decreasing component has been associated with strained Si under Ag and the increasing component with strained Si under SiO2, which has been formed partly prior to the XRD experiment and partly during sample heating. The opposite trends of these two Si-d(111) components are because of the larger value of α for Ag (7 times) and smaller for SiO2 (1/5th) compared to Si. The out-of-plane strain partitioning has been such that at room temperature, the Si substrate is unstrained and the strain in Ag is ˜0.3%. At 800 °C, Ag is practically relaxed, while Si under Ag is ˜-0.7% strained. A temperature dependent strain partitioning factor has been introduced to fit the data.

  13. Behavior of the thermal expansion coefficient of {alpha}-MoO{sub 3} as a function of the concentration of the Nd{sup 3+} ion

    Energy Technology Data Exchange (ETDEWEB)

    Alfonso, J.E., E-mail: jealfonsoo@unal.edu.co [Department of Physics, Universidad Nacional de Colombia, Carrera 30 No. 45-03, Bogota 11001000 (Colombia); Garzon, R. [Engineering project, Universidad Distrital Francisco Jose de Caldas, Carrera 7 No. 40-53, Bogota 11001000 (Colombia); Moreno, L.C. [Department of Chemistry, Universidad Nacional de Colombia, Carrera 30 No 45-03, Bogota 11001000 (Colombia)

    2012-10-01

    We carried out a comparative study of the thermal dilatation coefficient of molybdenum trioxide with and without Nd{sup 3+} doping. The doped samples were obtained from a solid state reaction of MoO{sub 3} and Nd{sub 2}O{sub 3} in concentrations from 0.2 to 20.0 at%. The prepared samples were analyzed as a function of the temperature through X-Ray diffraction (XRD), the chemical composition of the resultant material was studied using Energy Dispersive X-ray Spectroscopy (EDS). The results of the XRD show that the MoO{sub 3} doped with Nd in concentrations of 0.2 and 1.0% atomic grows iso-structurally with {alpha}-MoO{sub 3}. Moreover, MoO{sub 3} doped with Nd{sup 3+} in concentrations of 5.0, 10.0 and 20.0% atomic exhibits the monoclinic phase Mo{sub 9}O{sub 26}. Finally, we determined that the values of the thermal expansion coefficient of MoO{sub 3}, doped and un-doped, differ by less than 3%.

  14. Monte Carlo and theoretical calculations of the first four perturbation coefficients in the high temperature series expansion of the free energy for discrete and core-softened potential models

    Science.gov (United States)

    Zhou, Shiqi; Solana, J. R.

    2013-06-01

    The first four perturbation coefficients in the expansion of the Helmholtz free energy in power series of the inverse of the reduced temperature for a number of potential models with hard-sphere cores plus core-softened and discontinuous tails are obtained from Monte Carlo simulations. The potential models considered include square-well, double square-well, and square-shoulder plus square-well, with different potential parameters. These simulation data are used to evaluate the performance of a traditional macroscopic compressibility approximation (MCA) for the second order coefficient and a recent coupling parameter series expansion (CPSE) for the first four coefficients. Comprehensive comparison indicates the incapability of the MCA for the second order coefficient in most non-stringent situations, and significance of the CPSE in accurately calculating these four coefficients.

  15. Volumetric Virtual Environments

    Institute of Scientific and Technical Information of China (English)

    HE Taosong

    2000-01-01

    Driven by fast development of both virtual reality and volume visualization, we discuss some critical techniques towards building a volumetric VR system, specifically the modeling, rendering, and manipulations of a volumetric scene.Techniques such as voxel-based object simplification, accelerated volume rendering,fast stereo volume rendering, and volumetric "collision detection" are introduced and improved, with the idea of demonstrating the possibilities and potential benefits of incorporating volumetric models into VR systems.

  16. Expansion in chickpea (Cicer arietinum L.) seed during soaking and cooking

    Science.gov (United States)

    Sayar, Sedat; Turhan, Mahir; Köksel, Hamit

    2016-01-01

    The linear and volumetric expansion of chickpea seeds during water absorption at 20, 30, 50, 70, 85 and 100°C was studied. Length, width and thickness of chickpea seeds linearly increased with the increase in moisture content at all temperatures studied, where the greatest increase was found in length. Two different mathematical approaches were used for the determination of the expansion coefficients. The plots of the both linear and volumetric expansion coefficients versus temperature exhibited two linear lines, the first one was through 20, 30 and 50ºC and the second one was trough 70, 85 and 100ºC. The crossing point (58ºC) of these lines was very close to the gelatinisation temperature (60ºC) of chickpea starch.

  17. Superplastic forming of Ti6Al4V alloy using ZrO_2-TiO_2 ceramic die with adjustable linear thermal expansion coefficient

    Institute of Scientific and Technical Information of China (English)

    JIANG Shao-song; ZHANG Kai-feng

    2009-01-01

    Firstly, the relation between the coefficient of thermal expansion(CTE) and the volume fraction of TiO_2 was investigated, and also the influence of relative density of ceramic on the CTE was studied. The results show that the volume fraction, of TiO_2 and the relative density both make influence on the CTE of ZrO_2-TiO_2 ceramic. According to the results, the ZrO_2-TiO_2(volume fraction of TiO_2 is 27%) ceramic die with the similar CTE (8.92×10~(-6)℃~(-1)) to Ti6Al4V was fabricated. Secondly, to evaluate the dimensional accuracy of the workpiece superplastically formed, the Ti6Al4V impression experiment was performed. The result shows that the dimensional inaccuracy of workpieee is 0.003. Thirdly, in order to evaluate the practicability, the experiment of superplastic forming Ti6Al4V using ZrO_2-TiO_2 cylinder ceramic die was carried out. The Ti6Al4V cylinder shows good shape retention and surface quality, and high dimensional accuracy. The ceramic dies seem to be adequate for superplastic forming the high accuracy Ti6Al4V,and the trials have confirmed the potential of the ZrO2-TiO2 ceramic die.

  18. The enhanced range of temperature for coefficient of low thermal expansion, electrical and thermal conductivities of Cu substituted Fe-Ni invar alloys

    Science.gov (United States)

    Khan, S. A.; Ziya, A. B.; Ibrahim, A.; Atiq, S.; Ahmad, N.; Bashir, F.

    2016-03-01

    Six alloys of Fe65Ni35-x Cu x (x = 0, 0.2, 0.6, 1, 1.4, 1.8 at.%) have been prepared by conventional arc-melting technique and characterized by utilizing high temperature x-ray diffraction (HTXRD) technique at a range from room temperature to 773 K for determination of phase, lattice parameter (a), coefficient of thermal expansion (α(T)), mean square amplitude of vibration (\\bar{{u}2}), characteristic Debye temperature (ΘD), electrical resistivity (ρ) and thermal conductivity (κ). The studies showed that these alloys form face centered cubic structure (fcc) throughout the investigated temperature range. The values of α(T) were found to be comparable to those for conventional Fe-Ni invar alloys but have increased temperature span to a significant extent. The mean square amplitude of vibration (\\bar{{u}2}) and Debye temperature were found to remain almost unchanged in the invar temperature range, whereas the electrical and thermal conductivity were found to improve.

  19. Effects of heat treatment temperature on crystallization and thermal expansion coefficient of Li2 O-Al2 O3-SiO2

    Institute of Scientific and Technical Information of China (English)

    卢安贤; 贾明; 刘树江

    2004-01-01

    The basic glass of Li2 O-Al2 O3-SiO2 system using P2O5 as nucleator was prepared by means of conventional melt quenching technology, and the heat-treatment process was determined by using differential thermal analysis. The crystalline phases and the microstructure of the glass-ceramics were investigated by using X-ray diffraction and scanning electron microscopy. The results show that the glass based on Li2 O-Al2 O3-SiO2 oxides using P2 O5 as nucleator can be prepared at lower melt temperature of 1 450 ℃ and the glass-ceramics with lower thermal expansion coefficient of 21.6 × 10-7 ℃ 1 can also be obtained at 750 ℃. The glass-ceramics contain a few crystal phases in which the main crystal phase is β-quartz solid solution and the second crystal phase is β-spodumene solid solution. When the heat treatment temperature is not higher than 650 ℃, the transparent glass-ceramics containing β-quartzsolid solution can be prepared. β-quartz solid solution changes into β-spodumene solid solution at about 750 ℃. And the appearance of the glass-ceramics changes from translucent, part opaque to complete opaque with increasing temperature.

  20. Metal Linear Expansion Coefficient Measuring Based on Laser Diffraction%激光衍射法测金属线胀系数

    Institute of Scientific and Technical Information of China (English)

    许巧平

    2015-01-01

    In this paper,we proposed a new method for measuring metal linear expansion coefficient based on the principle of single slit diffraction of light. By using the two blades to make a slit,one blade is fixed on the hob,the other is fixed on the metal bar indirectly. Activity slit width becomes smaller when the metal bar heated to be expanded. And the diffraction fringe width changes when the laser passes through the slit. The elongation of metal bar can be calculated by measuring fringe change.%介绍了一种利用光的衍射原理测量金属线胀系数的新方法。利用两个刀片构成一活动狭缝。其中一刀片固定在铁架台支架上,另一刀片间接固定在金属棒上,当金属棒受热膨胀时,活动狭缝变小。在激光照射下,形成单缝衍射条纹的宽度发生变化,通过测量条纹的变化计算出金属丝的伸长量。

  1. New Family of Materials with Negative Coefficients of Thermal Expansion: The Effect of MgO, CoO, MnO, NiO, or CuO on the Phase Stability and Thermal Expansion of Solid Solution Phases Derived from BaZn2Si2O7.

    Science.gov (United States)

    Thieme, Christian; Waurischk, Tina; Heitmann, Stephan; Rüssel, Christian

    2016-05-02

    Recently, a silicate with the composition SrxBa1-xZn2Si2O7 was reported, which exhibits a negative coefficient of thermal expansion. The compound BaZn2Si2O7 shows a highly positive coefficient of thermal expansion up to a temperature of 280 °C and then transfers to a high temperature phase, which exhibits a coefficient of thermal expansion near zero or negative over a limited temperature range up to around 500 °C. This high temperature modification can be stabilized to room temperature if Ba(2+) is replaced by Sr(2+). In the solid solution SrxBa1-xZn2Si2O7, also Zn(2+) can be replaced in a wide concentration range by other cations with the respective valency. In the present study, Zn was partially or completely replaced by Mg, Co, Mn, Ni, or Cu. If the high temperature phase is stable at room temperature, the thermal expansion is negative, and if the partial substitution exceeds a certain concentration threshold, the low temperature phase with the crystal structure of BaZn2Si2O7 and highly positive thermal expansion is formed. The lowest mean coefficients of thermal expansion were measured for the composition Ba0.5Sr0.5Zn1.4Co0.6Si2O7 with a value of -2.9 × 10(-6) K(-1). In general, a lower Zn-concentration leads to a higher anisotropy and a lower mean coefficient of thermal expansion.

  2. ARCH(0,1)系数中位无偏估计分布的渐近展开%Asymptotic Expansion for the Distribution of a Median Unbiased Estimator of ARCH(0,1) Coefficient

    Institute of Scientific and Technical Information of China (English)

    王德辉

    2007-01-01

    This paper is concerned with the distributional properties of a median unbiased estimator of ARCH(0,1) coefficient. The exact distribution of the estimator can be easily derived, however its practical calculations are too heavy to implement,even though the middle range of sample sizes. Since the estimator is shown to have asymptotic normality, asymptotic expansions for the distribution and the percentiles of the estimator are derived as the refinements. Accuracies of expansion formulas are evaluated numerically, and the results of which show that we can effectively use the expansion as a fine approximatioh of the distribution with rapid calculations. Derived expansion are applied to testing hypothesis of stationarity, and an implementation for a real data set is illustrated.

  3. Prediction of the thermal expansion coefficients of bio diesels from several sources through the application of linear regression; Predicao dos coeficientes de expansao termica de biodieseis de diversas origens atraves da aplicacao da regressa linear

    Energy Technology Data Exchange (ETDEWEB)

    Canciam, Cesar Augusto [Universidade Tecnologica Federal do Parana (UTFPR), Campus Ponta Grossa, PR (Brazil)], e-mail: canciam@utfpr.edu.br

    2012-07-01

    When evaluating the consumption of bio fuels, the knowledge of the density is of great importance for rectify the effect of temperature. The thermal expansion coefficient is a thermodynamic property that provides a measure of the density variation in response to temperature variation, keeping the pressure constant. This study aimed to predict the thermal expansion coefficients of ethyl bio diesels from castor beans, soybeans, sunflower seeds and Mabea fistulifera Mart. oils and of methyl bio diesels from soybeans, sunflower seeds, souari nut, cotton, coconut, castor beans and palm oils, from beef tallow, chicken fat and hydrogenated vegetable fat residual. For this purpose, there was a linear regression analysis of the density of each bio diesel a function of temperature. These data were obtained from other works. The thermal expansion coefficients for bio diesels are between 6.3729x{sup 10-4} and 1.0410x10{sup -3} degree C-1. In all the cases, the correlation coefficients were over 0.99. (author)

  4. Effect of Main Components on the Linear Thermal Expansion Coefficient of Wood-Plastic Composite%木塑复合材料配方组成对其线性热膨胀系数的影响

    Institute of Scientific and Technical Information of China (English)

    蔡培鑫; 吕群; 梁梦杰; 来国桥

    2011-01-01

    Wood plastic composites(WPC) were prepared by extrusion with PP, HDPE,POE,EPDM or their blends as a plastic substrate and wood flour as a filler. The effects of the thermal expansion characteristics of the components, the plastic substrate composition and wood flour content in the formulas on the linear thermal expansion coefficient of WPC were studied. The results showed that the order of linear thermal expansion coefficients of main raw materials in WPC was that wood flour < PP < PE < toughening agent and the linear thermal expansion coefficient of WPC increased with increasing the plastic content because that the linear thermal expansion coefficient of the plastic was much greater than wood flour. The linear thermal expansion coefficient of WPC decreased with increasing PP/PE ratio in the formula and increased with increasing the amount of toughening agents EPDM or POE.%以PP、HDPE、POE、EPDM或其共混物作为塑料基体,以木粉作为填充料,用挤出成型法制备了PP/PE基和PP基木塑复合材料(WPC),研究了配方中各组分的热膨胀特性、配方中塑料基体组成变化、以及配方中木粉含量变化等因素对所制得的WPC线性热膨胀系数的影响.结果表明:制备WPC的主要原料线性热膨胀系数的大小顺序为:木粉<聚丙烯<聚乙烯<增韧剂,其中各塑料成分的线性热膨胀系数均远大于木粉,随着WPC中塑料含量增加,WPC的线性热膨胀系数增加;随着配方中PP/PE比值增加,WPC的线性热膨胀系数减小;随着配方中增韧剂EPDM或POE用量增加,WPC的线性热膨胀系数增大.

  5. Probing volumetric properties of biomolecular systems by pressure perturbation calorimetry (PPC)--the effects of hydration, cosolvents and crowding.

    Science.gov (United States)

    Suladze, Saba; Kahse, Marie; Erwin, Nelli; Tomazic, Daniel; Winter, Roland

    2015-04-01

    Pressure perturbation calorimetry (PPC) is an efficient technique to study the volumetric properties of biomolecules in solution. In PPC, the coefficient of thermal expansion of the partial volume of the biomolecule is deduced from the heat consumed or produced after small isothermal pressure-jumps. The expansion coefficient strongly depends on the interaction of the biomolecule with the solvent or cosolvent as well as on its packing and internal dynamic properties. This technique, complemented with molecular acoustics and densimetry, provides valuable insights into the basic thermodynamic properties of solvation and volume effects accompanying interactions, reactions and phase transitions of biomolecular systems. After outlining the principles of the technique, we present representative examples on protein folding, including effects of cosolvents and crowding, together with a discussion of the interpretation, and further applications. Copyright © 2014 Elsevier Inc. All rights reserved.

  6. Prediction of final settlements of buildings constructed on expansive soils

    Directory of Open Access Journals (Sweden)

    María-de-la-Luz Pérez-Rea

    2015-06-01

    Full Text Available Because the action of the swelling pressure, the settlements caused by the transmitted load from the structure on expansive soils, and the settlements calculated by classic theories of soils mechanics are different. This swelling pressure acts in opposite direction to the weight of the building. In this paper, the authors propose the use of a volumetric strain coefficient by settlements exp, in a soil-structure interaction algorithm taking into account the expansive soil behavior in the reduction of the settlement magnitude when a building is placed above soil. It’s necessary to know the initial properties of the expansive unsaturated soil and the load building conditions. A laboratory process is described for determining the aexpcoefficient.

  7. Contrast Enhanced Microscopy Digital Image Correlation: A General Method to Contact-Free Coefficient of Thermal Expansion Measurement of Polymer Films

    Science.gov (United States)

    Jairo A. Diaz; Robert J. Moon; Jeffrey P. Youngblood

    2014-01-01

    Thermal expansion represents a vital indicator of the processing history and dimensional stability of materials. Solvent-sensitive, thin, and compliant samples are particularly challenging to test. Here we describe how textures highlighted by contrast enhanced optical microscopy modes (i.e., polarized light (PL), phase contrast (PC)) and bright field (BF) can be used...

  8. Thermal expansion of lattice parameter of (powder) silicon up to 1473 K

    Institute of Scientific and Technical Information of China (English)

    XING Xianran; CHEN Jun; DENG Jinxia; LIU Guirong

    2004-01-01

    The XRPD (X-ray powder diffractometry) patterns of silicon powder with a unit cell structure of diamond were determined from 298 to 1473 K. Lattice parameters of Si linearly increase with temperature. The thermal shifts of the positions of all reflection peaks are linearly correlated with the temperature. The coefficients of the intrinsic linear thermal expansion and volumetric thermal expansion were determined as 3.87×10-6/K and 1.16 × 10-5/K respectively. It indicates that Si is still a suitable standard in the XRPD method at high temperatures.

  9. Mechanical properties and coefficient of thermal expansion of β-eucryptite sintered by microwave technique; Propiedades mecanicas y coeficiente de dilatacion termica de la β-eucriptita sinterizada por la tecnica de microondas

    Energy Technology Data Exchange (ETDEWEB)

    Benavente, R.; Borrell, A.; Salvador, M. D.; Garcia-Moreno, O.; Penaranda-Foix, F. L.; Catala-Civera, J. M.

    2014-10-01

    Microwave non-conventional sintering technique allows obtaining fully dense glass-free β-eucryptite bulk material (∼99 %). A considerable difference in the densification, microstructure, coefficient of thermal expansion behaviour and mechanical properties, between conventional and non-conventional sintered specimens was observed. The hardness and Young's modulus values obtained by microwaves at 1200 degree centigrade-5min have been relatively high, 6.8 GPa and 101 GPa, respectively, compared to conventional sintering (3.9 GPa and 58 GPa, respectively). Very low thermal expansion materials have been obtained in a wide temperature range including cryogenic temperatures (from -150 degree centigrade to 150 degree centigrade). The high heating rate along with the lower energy consumption makes microwave technique a clear alternative to other types of sintering methods. (Author)

  10. MR volumetric assessment of endolymphatic hydrops

    Energy Technology Data Exchange (ETDEWEB)

    Guerkov, R.; Berman, A.; Jerin, C.; Krause, E. [University of Munich, Department of Otorhinolaryngology Head and Neck Surgery, Grosshadern Medical Centre, Munich (Germany); University of Munich, German Centre for Vertigo and Balance Disorders, Grosshadern Medical Centre, Marchioninistr. 15, 81377, Munich (Germany); Dietrich, O.; Flatz, W.; Ertl-Wagner, B. [University of Munich, Institute of Clinical Radiology, Grosshadern Medical Centre, Munich (Germany); Keeser, D. [University of Munich, Institute of Clinical Radiology, Grosshadern Medical Centre, Munich (Germany); University of Munich, German Centre for Vertigo and Balance Disorders, Grosshadern Medical Centre, Marchioninistr. 15, 81377, Munich (Germany); University of Munich, Department of Psychiatry and Psychotherapy, Innenstadtkliniken Medical Centre, Munich (Germany)

    2014-10-16

    We aimed to volumetrically quantify endolymph and perilymph spaces of the inner ear in order to establish a methodological basis for further investigations into the pathophysiology and therapeutic monitoring of Meniere's disease. Sixteen patients (eight females, aged 38-71 years) with definite unilateral Meniere's disease were included in this study. Magnetic resonance (MR) cisternography with a T2-SPACE sequence was combined with a Real reconstruction inversion recovery (Real-IR) sequence for delineation of inner ear fluid spaces. Machine learning and automated local thresholding segmentation algorithms were applied for three-dimensional (3D) reconstruction and volumetric quantification of endolymphatic hydrops. Test-retest reliability was assessed by the intra-class coefficient; correlation of cochlear endolymph volume ratio with hearing function was assessed by the Pearson correlation coefficient. Endolymph volume ratios could be reliably measured in all patients, with a mean (range) value of 15 % (2-25) for the cochlea and 28 % (12-40) for the vestibulum. Test-retest reliability was excellent, with an intra-class coefficient of 0.99. Cochlear endolymphatic hydrops was significantly correlated with hearing loss (r = 0.747, p = 0.001). MR imaging after local contrast application and image processing, including machine learning and automated local thresholding, enable the volumetric quantification of endolymphatic hydrops. This allows for a quantitative assessment of the effect of therapeutic interventions on endolymphatic hydrops. (orig.)

  11. The Dependence of the Change in the Coefficient of Thermal Expansion of Graphite Fiber Reinforced Polyimide IM7-K3B on Microcracking due to Thermal Cycling

    Science.gov (United States)

    Stewart, Melissa C.

    1995-01-01

    Composite IM7-K3B was subjected to a simulated high speed aircraft thermal environment to determine the effects of microcracking on the change in CTE. IM7-K3B is a graphite fiber reinforced polyimide laminate, manufactured by Dupont. The lay-up for the material was (0.90((Sub 3)(Sub s))). The specimens were placed in a laser-interferometric dilatometer to obtain thermal expansion measurements and were then repeatedly cycled between -65 F and 350 F up to 1000 cycles. After cycling they were scanned for microcracks at a magnification of 400x. The material was expected not to crack and to have a near zero CTE. Some microcracking did occur in all specimens and extensive microcracking occurred in one specimen. Further testing is required to determine how closely the CTE and microcracking are related.

  12. 以改进的迈克尔逊干涉仪测量LED封装材料的热膨胀系数%Measurement of Coefficient of Thermal Expansion of Encapsulation Material in LED Using Michelson Interferometer

    Institute of Scientific and Technical Information of China (English)

    李相剑; 李华祯; 郑改革; 陈玉林; 张成义

    2014-01-01

    LED封装材料在封装的过程中由于热膨胀的缘故会产生应力,将对LED的发光效率产生较大影响。本文将改装的迈克尔逊干涉仪用于测量二氧化钛/有机硅复合的LED封装材料在不同温度范围内的热膨胀系数,具有测量准确,分辨率高等优点。%LED packaging material can cause stress due to thermal expansion in the packaging process, will have a greater impact on the luminous efficiency of LED. The modified Michelson interferometer is used to measure the thermal expansion coefficient of composite LED packaging material with TiO2 and organic Si in dif-ferent temperature range expansions;it has the advantages of accurate measurement,high resolution.

  13. Volumetric composition of nanocomposites

    DEFF Research Database (Denmark)

    Madsen, Bo; Lilholt, Hans; Mannila, Juha

    2015-01-01

    Detailed characterisation of the properties of composite materials with nanoscale fibres is central for the further progress in optimization of their manufacturing and properties. In the present study, a methodology for the determination and analysis of the volumetric composition of nanocomposites...... is presented, using cellulose/epoxy and aluminosilicate/polylactate nanocomposites as case materials. The buoyancy method is used for the accurate measurements of materials density. The accuracy of the method is determined to be high, allowing the measured nanocomposite densities to be reported with 5...... significant figures. The plotting of the measured nanocomposite density as a function of the nanofibre weight content is shown to be a first good approach of assessing the porosity content of the materials. The known gravimetric composition of the nanocomposites is converted into a volumetric composition...

  14. Colossal positive and negative thermal expansion and thermosalient effect in a pentamorphic organometallic martensite.

    Science.gov (United States)

    Panda, Manas K; Runčevski, Tomče; Sahoo, Subash Chandra; Belik, Alexei A; Nath, Naba K; Dinnebier, Robert E; Naumov, Panče

    2014-09-04

    The thermosalient effect is an extremely rare propensity of certain crystalline solids for self-actuation by elastic deformation or by a ballistic event. Here we present direct evidence for the driving force behind this impressive crystal motility. Crystals of a prototypical thermosalient material, (phenylazophenyl)palladium hexafluoroacetylacetonate, can switch between five crystal structures (α-ε) that are related by four phase transitions including one thermosalient transition (α↔γ). The mechanical effect is driven by a uniaxial negative expansion that is compensated by unusually large positive axial expansion (260 × 10(-6)  K(-1)) with volumetric expansion coefficients (≈250 × 10(-6)  K(-1)) that are among the highest values reported in molecular solids thus far. The habit plane advances at ~10(4) times the rate observed with non-thermosalient transitions. This rapid expansion of the crystal following the phase switching is the driving force for occurrence of the thermosalient effect.

  15. Pore size and concentration effect of mesoporous silica nanoparticles on the coefficient of thermal expansion and optical transparency of poly(ether sulfone) films.

    Science.gov (United States)

    Vo, Nhat Tri; Patra, Astam K; Kim, Dukjoon

    2017-01-18

    Mesoporous silica nanoparticles (MSNs) with uniform size (thermal expansion (CTE) without sacrificing optical transparency. Here, both CTE and optical transparency of the MSN/PES nanocomposite films gradually decreased with increasing MSN concentration. The PES films containing MSNs with larger pores showed the best performance in CTE and optical transparency. While the CTE decreased by 32.3% with increasing MSN content up to 0.5 wt%, the optical transparency decreased by only less than 6.9% because of the small and uniform particle size of less than 50 nm, which minimizes light scattering. This pore size effect is more clearly observed via an annealing process, which enables the polymer chains to slowly move and fill in the free volume in the pores of the MSN, and thus restricts the thermal motion. The effect of the silica nanoparticles was investigated not only on the thermal stability but also on the mechanical stability. We expect the MSNs synthesized in this study to be used as a promising filler to enhance the thermal and mechanical stability of the PES substrate without sacrificing its optical transparency.

  16. Thermal expansion of glassy polymers.

    Science.gov (United States)

    Davy, K W; Braden, M

    1992-01-01

    The thermal expansion of a number of glassy polymers of interest in dentistry has been studied using a quartz dilatometer. In some cases, the expansion was linear and therefore the coefficient of thermal expansion readily determined. Other polymers exhibited non-linear behaviour and values appropriate to different temperature ranges are quoted. The linear coefficient of thermal expansion was, to a first approximation, a function of both the molar volume and van der Waal's volume of the repeating unit.

  17. Flexible Volumetric Structure

    Science.gov (United States)

    Cagle, Christopher M. (Inventor); Schlecht, Robin W. (Inventor)

    2014-01-01

    A flexible volumetric structure has a first spring that defines a three-dimensional volume and includes a serpentine structure elongatable and compressible along a length thereof. A second spring is coupled to at least one outboard edge region of the first spring. The second spring is a sheet-like structure capable of elongation along an in-plane dimension thereof. The second spring is oriented such that its in-plane dimension is aligned with the length of the first spring's serpentine structure.

  18. Connectivity network measures predict volumetric atrophy in mild cognitive impairment.

    Science.gov (United States)

    Nir, Talia M; Jahanshad, Neda; Toga, Arthur W; Bernstein, Matt A; Jack, Clifford R; Weiner, Michael W; Thompson, Paul M

    2015-01-01

    Alzheimer's disease (AD) is characterized by cortical atrophy and disrupted anatomic connectivity, and leads to abnormal interactions between neural systems. Diffusion-weighted imaging (DWI) and graph theory can be used to evaluate major brain networks and detect signs of a breakdown in network connectivity. In a longitudinal study using both DWI and standard magnetic resonance imaging (MRI), we assessed baseline white-matter connectivity patterns in 30 subjects with mild cognitive impairment (MCI, mean age 71.8 ± 7.5 years, 18 males and 12 females) from the Alzheimer's Disease Neuroimaging Initiative. Using both standard MRI-based cortical parcellations and whole-brain tractography, we computed baseline connectivity maps from which we calculated global "small-world" architecture measures, including mean clustering coefficient and characteristic path length. We evaluated whether these baseline network measures predicted future volumetric brain atrophy in MCI subjects, who are at risk for developing AD, as determined by 3-dimensional Jacobian "expansion factor maps" between baseline and 6-month follow-up anatomic scans. This study suggests that DWI-based network measures may be a novel predictor of AD progression.

  19. 温度监测层数对坝体线膨胀系数反演影响%Effect of Number of Temperature Monitoring Layers on Inversion for Dam Concrete's Linear Thermal Expansion Coefficient

    Institute of Scientific and Technical Information of China (English)

    刘杨; 李含; 孔令娇

    2013-01-01

    Some analyses are made here with function fitting, basic principles of temperature displacement and relative mathematical calculation method to explain the difference and regularity between the adjusting parameters and inversion results of dam concrete' s linear thermal expansion coefficient, and the verification is made with some calculation examples . It is obtained that as the number of temperature monitoring layers increasing, the dam concrete's linear thermal expansion coefficient obtained from inversion would gradually approach to the true value. The conclusion would have high value of reference in the comprehensive analysis for the condition parameters of dam materials and related aspects of dam safety evaluation.%以函数拟合法、温度位移基本原理以及应用相关的数学计算方法进行分析解释坝体混凝土线膨胀系数的调整参数与反演的线膨胀系数出现一定差异呈现一定的规律性并通过实例计算予以验证.得出随着温度监测层数的增多,所反演得出的坝体混凝土线膨胀系数逐渐趋近真值,该结论对坝体材料性态参数的综合分析以及大坝相关方面安全评价具有参考价值.

  20. Transient and residual stresses and displacements in self-curing bone cement - Part I: characterization of relevant volumetric behavior of bone cement.

    Science.gov (United States)

    Ahmed, A M; Pak, W; Burke, D L; Miller, J

    1982-02-01

    In this first part of a two-part report, some aspects of the volumetric behavior of bone cement during its curing process are examined as a prelude to an analysis for the transient and residual stresses and displacements in stem fixation systems. Experiments show that stress generation in the cement is associated with its temperature while curing and that during the cooling phase, the stresses are mainly due to thermal as opposed to bulk shrinkage. The appropriate coefficient of thermal expansion of bone cement has been evaluated from measurements in a simulated fixation system in conjuction with a thermoelastic analysis.

  1. Design of Measuring Equipment to Explore Solid Linear Expansion Coefficient Based on Aplanatism Method%基于等光程法测量固体线膨胀系数装置的设计

    Institute of Scientific and Technical Information of China (English)

    李儒颂; 孙继远; 徐芹

    2015-01-01

    基于迈克尔逊干涉仪能够测量微小长度变化量的原理,自行改装并设计出利用等光程法实现对固体材料线膨胀系数精确测量的装置。基本思路是将原迈克尔逊干涉仪上的两个反射镜都改装成动镜,并将改装后的一动镜放在新增的导轨上,然后将其和待测金属棒的一端相连接,当金属棒受热后会产生细微的伸长,进而顶着动镜产生细微的移动,通过调节并观测受热前后屏上干涉条纹“缩进”和“涌出”的分界点来确定金属棒产生的微小形变量,然后根据公式计算出待测金属棒的线膨胀系数。该测量方法克服了传统数条纹方式的缺陷,可实现对金属棒线膨胀系数的精确测量,具有操作简便,实用性强的优点。%Based on the principle that the Michelson interferometer can be used to measure the slight variation in length, a device for accurate measurement of thermal expansion coefficient of solid material line by using the method of equal optical path is revised and designed. The basic idea is that two pieces of mirror on original Michel⁃son interferometer are converted into moving mirror, are put on the new added rail, and are connected with one end of the tested metal rod. When the metal rod is heated, it will lengthen slightly, which drives the moving mirror to pro⁃duce a slight movement. By adjusting and observing the demarcation point of the interference fringes ’“indenta⁃tion”and“emission”on the observation screen before and after heating, the micro change of the shape of the metal rod can be determined. And then, the coefficient of linear thermal expansion of the tested metal rod is calculated ac⁃cording to the formula. The method overcomes the defects of traditional fringe method, and can realize the accurate measurement of the coefficient of linear thermal expansion of the metal rods. This method has the advantages of sim⁃ple in operation and practical.

  2. Effect of the working liquid compressibility on the picture of volumetric and mechanical losses in a high pressure displacement pump used in a hydrostatic drive

    National Research Council Canada - National Science Library

    Paszota, Zygmunt

    2012-01-01

    Working liquid compressibility may considerably change the values and proportions of coefficients of volumetric and mechanical energy losses in the displacement pump used in a hydrostatic drive system...

  3. Performance characteristics of low global warming potential R134a alternative refrigerants in ejector-expansion refrigeration system

    Directory of Open Access Journals (Sweden)

    Mishra Shubham

    2016-12-01

    Full Text Available Performance assessment of ejector-expansion vapor compression refrigeration system with eco-friendly R134a alternative refrigerants (R152a, R1234yf, R600a, R600, R290, R161, R32, and propylene is presented for air-conditioning application. Ejector has been modeled by considering experimental data based correlations of component efficiencies to take care of all irreversibilities. Ejector area ratio has been optimized based on maximum coefficient of performance (COP for typical air-conditioner operating temperatures. Selected refrigerants have been compared based on area ratio, pressure lift ratio, entrainment ratio, COP, COP improvement and volumetric cooling capacity. Effects of normal boiling point and critical point on the performances have been studied as well. Using ejector as an expansion device, maximum improvement in COP is noted in R1234yf (10.1%, which reduces the COP deviation with R134a (4.5% less in basic cycle and 2.5% less in ejector cycle. Hence, R1234yf seems to be best alternative for ejector expansion system due to its mild flammability and comparable volumetric capacity and cooling COP. refrigerant R161 is superior to R134a in terms of both COP and volumetric cooling capacity, although may be restricted for low capacity application due to its flammability.

  4. Disentangling volumetric and hydrational properties of proteins.

    Science.gov (United States)

    Voloshin, Vladimir P; Medvedev, Nikolai N; Smolin, Nikolai; Geiger, Alfons; Winter, Roland

    2015-02-05

    We used molecular dynamics simulations of a typical monomeric protein, SNase, in combination with Voronoi-Delaunay tessellation to study and analyze the temperature dependence of the apparent volume, Vapp, of the solute. We show that the void volume, VB, created in the boundary region between solute and solvent, determines the temperature dependence of Vapp to a major extent. The less pronounced but still significant temperature dependence of the molecular volume of the solute, VM, is essentially the result of the expansivity of its internal voids, as the van der Waals contribution to VM is practically independent of temperature. Results for polypeptides of different chemical nature feature a similar temperature behavior, suggesting that the boundary/hydration contribution seems to be a universal part of the temperature dependence of Vapp. The results presented here shine new light on the discussion surrounding the physical basis for understanding and decomposing the volumetric properties of proteins and biomolecules in general.

  5. Influence of Temperature on Thermal Expansion Coefficient and Thermal Conductivity of HMX Based Polymer Bonded Explosive%温度对HMX基PBX炸药热膨胀系数和热导率的影响

    Institute of Scientific and Technical Information of China (English)

    韦兴文; 周筱雨; 王培; 涂小珍; 王翕

    2012-01-01

    The effect of temperature on thermal expansion and thermal conductivity of the HMX based polymer bonded explosive (PBX) were investigated by a thermal expansion analyzer and a flash thermal conductivity analyzer. The results show that coefficient of thermal expansion of HMX based PBX is about 5. 34 × 10-5 K-1 below 330K, which rapidly reachs to 13. 47 ×10-3 K-1 at temperature ranging from 330K to 350K, and decreases to 8. 04 × 10-5 K-1 above 350K. The specific heat capacity increases monotonically as temperature increasing, which ranging from 0. 978J · g-1 · K-1 to 1. 254J · g-1 · K-1 between 293K and 373K. But it is abnormal big at temperature about 343K as a result of the molten of the binder. The thermal diffusivity is 0. 256mm2 · s-1 at 293K and decreases to 0. 179mm2 · s-1 at 373K. The thermal conductivity is 0. 462W · m-1 · K-1 at 293K, decreasing to 0. 406W · m-1 · K-1 at 373K. The thermal conductivity and specific heat capacty variation with the temperature are established based on heat transfer theory of molecular crystal, and the thermal conductivities of HMX based PBX calculated from the two-phase vertical system model are in good agreement with the experiment%用热膨胀仪和闪光导热仪研究了温度对HMX基PBX的热膨胀系数和热导率的影响.结果表明,在低于330K时,HMX基PBX的线膨胀系数约为5.34×10-5 K-1;在330~350K,线膨胀系数迅速增大到13.47×10-5K-1,随着黏结剂软化,线膨胀系数随之减小到8.04×10-5K-1.在293~373K,HMX基PBX的比热容从0.978J·g-1·K-1线性增长到1.254J·g-1·K-1,但在343K附近黏结剂融化存在异常偏大值;HMX基PBX的热扩散率从0.256mm2·s-1下降至0.179mm2·s-1,通过比热和热扩散率实验数据计算获得的热导率从0.462W·m-1·K-1下降至0.406W·m-1·K-1.基于分子晶体传热理论模型建立了比热和导热系数的温度关系函数,HMX基PBX的导热机制符合两相串联模型.

  6. Quantitative Techniques in Volumetric Analysis

    Science.gov (United States)

    Zimmerman, John; Jacobsen, Jerrold J.

    1996-12-01

    Quantitative Techniques in Volumetric Analysis is a visual library of techniques used in making volumetric measurements. This 40-minute VHS videotape is designed as a resource for introducing students to proper volumetric methods and procedures. The entire tape, or relevant segments of the tape, can also be used to review procedures used in subsequent experiments that rely on the traditional art of quantitative analysis laboratory practice. The techniques included are: Quantitative transfer of a solid with a weighing spoon Quantitative transfer of a solid with a finger held weighing bottle Quantitative transfer of a solid with a paper strap held bottle Quantitative transfer of a solid with a spatula Examples of common quantitative weighing errors Quantitative transfer of a solid from dish to beaker to volumetric flask Quantitative transfer of a solid from dish to volumetric flask Volumetric transfer pipet A complete acid-base titration Hand technique variations The conventional view of contemporary quantitative chemical measurement tends to focus on instrumental systems, computers, and robotics. In this view, the analyst is relegated to placing standards and samples on a tray. A robotic arm delivers a sample to the analysis center, while a computer controls the analysis conditions and records the results. In spite of this, it is rare to find an analysis process that does not rely on some aspect of more traditional quantitative analysis techniques, such as careful dilution to the mark of a volumetric flask. Figure 2. Transfer of a solid with a spatula. Clearly, errors in a classical step will affect the quality of the final analysis. Because of this, it is still important for students to master the key elements of the traditional art of quantitative chemical analysis laboratory practice. Some aspects of chemical analysis, like careful rinsing to insure quantitative transfer, are often an automated part of an instrumental process that must be understood by the

  7. Quadrature formulas for Fourier coefficients

    KAUST Repository

    Bojanov, Borislav

    2009-09-01

    We consider quadrature formulas of high degree of precision for the computation of the Fourier coefficients in expansions of functions with respect to a system of orthogonal polynomials. In particular, we show the uniqueness of a multiple node formula for the Fourier-Tchebycheff coefficients given by Micchelli and Sharma and construct new Gaussian formulas for the Fourier coefficients of a function, based on the values of the function and its derivatives. © 2009 Elsevier B.V. All rights reserved.

  8. Test Facility for Volumetric Absorber

    Energy Technology Data Exchange (ETDEWEB)

    Ebert, M.; Dibowski, G.; Pfander, M.; Sack, J. P.; Schwarzbozl, P.; Ulmer, S.

    2006-07-01

    Long-time testing of volumetric absorber modules is an inevitable measure to gain the experience and reliability required for the commercialization of the open volumetric receiver technology. While solar tower test facilities are necessary for performance measurements of complete volumetric receivers, the long-term stability of individual components can be tested in less expensive test setups. For the qualification of the aging effects of operating cycles on single elements of new absorber materials and designs, a test facility was developed and constructed in the framework of the KOSMOSOL project. In order to provide the concentrated solar radiation level, the absorber test facility is integrated into a parabolic dish system at the Plataforma Solar de Almeria (PSA) in Spain. Several new designs of ceramic absorbers were developed and tested during the last months. (Author)

  9. Structure and thermal expansion of liquid bismuth

    Directory of Open Access Journals (Sweden)

    Mudry S.

    2015-12-01

    Full Text Available Experimental structural data for liquid Bi were used for estimation of the main structure parameters as well as the thermal expansion coefficient both in supercooled and superheated temperature ranges. It was shown that the equilibrium melt had a positive thermal expansion coefficient within a temperature range upon melting and a negative one at higher temperatures. The former was related to structure changes upon melting, whereas the latter with topologic disordering upon further heating. It was found that the superheated melt had a negative thermal expansion coefficient. The results obtained from structural data were compared with the thermal expansion coefficient calculated from the data of density for liquid Bi.

  10. Thermal expansion of simulated thoria-urania fuel by high temperature XRD

    Science.gov (United States)

    Bhagat, R. K.; Krishnan, K.; Kutty, T. R. G.; Kumar, Arun; Kamath, H. S.; Banerjee, S.

    2012-03-01

    The thermal expansion behavior of polycrystalline samples of ThO2-3.45% UO2 and SIMFUEL corresponding to burn-up of 43,000 MWd/Te has been investigated from room temperature to 1473 K, and for SIMFUEL corresponding to burn-up of 28,000 MWd/Te has been investigated from room temperature to 1173 K, using a high temperature X-ray diffraction (HTXRD). Linear and volumetric thermal expansion data like, percentage thermal expansion, average or mean coefficient of thermal expansion (CTE) was generated using the lattice parameters. It is observed that SIMFUEL has a lower lattice parameter compared to ThO2-3.45% UO2 and this is attributed to the dissolution of the rare earths and part of the Zr and Ce in fuel matrix. Also SIMFUEL has slightly higher thermal expansion than ThO2-3.45% UO2 and this is related to the lower melting point of SIMFUEL.

  11. Thermal expansion of simulated thoria-urania fuel by high temperature XRD

    Energy Technology Data Exchange (ETDEWEB)

    Bhagat, R.K. [Radiometallurgy Division, Bhabha Atomic Research Centre, Trombay, Mumbai 400 085 (India); Krishnan, K. [Fuel Chemistry Division, Bhabha Atomic Research Centre, Trombay, Mumbai 400 085 (India); Kutty, T.R.G., E-mail: tkutty@barc.gov.in [Radiometallurgy Division, Bhabha Atomic Research Centre, Trombay, Mumbai 400 085 (India); Kumar, Arun [Radiometallurgy Division, Bhabha Atomic Research Centre, Trombay, Mumbai 400 085 (India); Kamath, H.S. [Nuclear Fuels Group, Bhabha Atomic Research Centre, Trombay, Mumbai 400 085 (India); Banerjee, S. [Department of Atomic Energy, Anushakti Bhavan, Mumbai 400 001 (India)

    2012-03-15

    The thermal expansion behavior of polycrystalline samples of ThO{sub 2}-3.45% UO{sub 2} and SIMFUEL corresponding to burn-up of 43,000 MWd/Te has been investigated from room temperature to 1473 K, and for SIMFUEL corresponding to burn-up of 28,000 MWd/Te has been investigated from room temperature to 1173 K, using a high temperature X-ray diffraction (HTXRD). Linear and volumetric thermal expansion data like, percentage thermal expansion, average or mean coefficient of thermal expansion (CTE) was generated using the lattice parameters. It is observed that SIMFUEL has a lower lattice parameter compared to ThO{sub 2}-3.45% UO{sub 2} and this is attributed to the dissolution of the rare earths and part of the Zr and Ce in fuel matrix. Also SIMFUEL has slightly higher thermal expansion than ThO{sub 2}-3.45% UO{sub 2} and this is related to the lower melting point of SIMFUEL.

  12. Zernike aberration coefficients transformed to and from Fourier series coefficients for wavefront representation.

    Science.gov (United States)

    Dai, Guang-Ming

    2006-02-15

    The set of Fourier series is discussed following some discussion of Zernike polynomials. Fourier transforms of Zernike polynomials are derived that allow for relating Fourier series expansion coefficients to Zernike polynomial expansion coefficients. With iterative Fourier reconstruction, Zernike representations of wavefront aberrations can easily be obtained from wavefront derivative measurements.

  13. Isotropic Negative Thermal Expansion Metamaterials.

    Science.gov (United States)

    Wu, Lingling; Li, Bo; Zhou, Ji

    2016-07-13

    Negative thermal expansion materials are important and desirable in science and engineering applications. However, natural materials with isotropic negative thermal expansion are rare and usually unsatisfied in performance. Here, we propose a novel method to achieve two- and three-dimensional negative thermal expansion metamaterials via antichiral structures. The two-dimensional metamaterial is constructed with unit cells that combine bimaterial strips and antichiral structures, while the three-dimensional metamaterial is fabricated by a multimaterial 3D printing process. Both experimental and simulation results display isotropic negative thermal expansion property of the samples. The effective coefficient of negative thermal expansion of the proposed models is demonstrated to be dependent on the difference between the thermal expansion coefficient of the component materials, as well as on the circular node radius and the ligament length in the antichiral structures. The measured value of the linear negative thermal expansion coefficient of the three-dimensional sample is among the largest achieved in experiments to date. Our findings provide an easy and practical approach to obtaining materials with tunable negative thermal expansion on any scale.

  14. Operator product expansion algebra

    Energy Technology Data Exchange (ETDEWEB)

    Holland, Jan [CPHT, Ecole Polytechnique, Paris-Palaiseau (France)

    2014-07-01

    The Operator Product Expansion (OPE) is a theoretical tool for studying the short distance behaviour of products of local quantum fields. Over the past 40 years, the OPE has not only found widespread computational application in high-energy physics, but, on a more conceptual level, it also encodes fundamental information on algebraic structures underlying quantum field theories. I review new insights into the status and properties of the OPE within Euclidean perturbation theory, addressing in particular the topics of convergence and ''factorisation'' of the expansion. Further, I present a formula for the ''deformation'' of the OPE algebra caused by a quartic interaction. This formula can be used to set up a novel iterative scheme for the perturbative computation of OPE coefficients, based solely on the zeroth order coefficients (and renormalisation conditions) as initial input.

  15. Volumetric Three-Dimensional Display Systems

    Science.gov (United States)

    Blundell, Barry G.; Schwarz, Adam J.

    2000-03-01

    A comprehensive study of approaches to three-dimensional visualization by volumetric display systems This groundbreaking volume provides an unbiased and in-depth discussion on a broad range of volumetric three-dimensional display systems. It examines the history, development, design, and future of these displays, and considers their potential for application to key areas in which visualization plays a major role. Drawing substantially on material that was previously unpublished or available only in patent form, the authors establish the first comprehensive technical and mathematical formalization of the field, and examine a number of different volumetric architectures. System level design strategies are presented, from which proposals for the next generation of high-definition predictable volumetric systems are developed. To ensure that researchers will benefit from work already completed, they provide: * Descriptions of several recent volumetric display systems prepared from material supplied by the teams that created them * An abstract volumetric display system design paradigm * An historical summary of 90 years of development in volumetric display system technology * An assessment of the strengths and weaknesses of many of the systems proposed to date * A unified presentation of the underlying principles of volumetric display systems * A comprehensive bibliography Beautifully supplemented with 17 color plates that illustrate volumetric images and prototype displays, Volumetric Three-Dimensional Display Systems is an indispensable resource for professionals in imaging systems development, scientific visualization, medical imaging, computer graphics, aerospace, military planning, and CAD/CAE.

  16. Thermal expansion of ceramics around room temperature

    OpenAIRE

    橋本, 忍; 安達, 信泰; 太田, 敏孝; 宮崎, 英敏; ハシモト, シノブ; アダチ, ノブヤス; オオタ, トシタカ; Hashimoto, Shinobu; Adachi, Nobuyasu; Ota, Toshitaka

    2010-01-01

    Thermal expansion of some ceramics, polymers and metals was measured by dilatometer around room temperature (from -140℃to +200℃), and compared with thermal expansion in the high temperature region. The CTE (coefficient of thermal expansion)of almost ceramics changed drastically between room temperature and high temperature region. On the other hand, the CTE ofmetals did not change between room temperature and high temperature region. The difference on thermal expansion betweenceramics and met...

  17. Design of materials with extreme thermal expansion using a three-phase topology optimization method

    DEFF Research Database (Denmark)

    Sigmund, Ole; Torquato, S.

    1997-01-01

    We show how composites with extremal or unusual thermal expansion coefficients can be designed using a numerical topology optimization method. The composites are composed of two different material phases and void. The optimization method is illustrated by designing materials having maximum thermal...... expansion, zero thermal expansion, and negative thermal expansion. Assuming linear elasticity, it is shown that materials with effective negative thermal expansion coefficients can be obtained by mixing two phases with positive thermal expansion coefficients and void. We also show...

  18. Estimation of thermal expansion properties of quasicrystalline alloys

    Institute of Scientific and Technical Information of China (English)

    齐育红; 张占平; 黑祖昆

    2004-01-01

    By investigating the thermal expansion properties of three quasicrystalline alloys Al65 Cu20 Cr15 quenched,Al65Cu20Cr15 cast and Al65Cu20Fe15 cast particles reinforced Al matrix composites from 25 ℃ to 500 ℃, the thermal expansion coefficients of three quasicrystalline alloys were theoretically estimated. The results show that the thermal expansion coefficients of the composites are much lower than that of pure Al, and the thermal expansion coefficients of the composites reinforced by Al-Cu-Cr quasicrystalline particles are lower than those of the composites reinforced by Al-Cu-Fe quasicrystalline particles. According to estimating, quasicrystalline alloys have negative thermal expansion coefficients, and the thermal expansion coefficients of Al-Cu-Cr quasicrystalline alloys are lower than those of Al-Cu-Fe quasicrystalline alloys. In the alloys, the more the qusicrystalline content, the lower the thermal expansion coefficient.

  19. Chemical and Thermal Expansion of Calcium-Doped Lanthanum Chromite

    Science.gov (United States)

    Williford, R. E.; Armstrong, T. R.; Gale, J. D.

    2000-02-01

    Atomistic free-energy minimization techniques were used to simulate three simultaneous volumetric shrinkage/expansion phenomena in calcium-doped lanthanum chromite solid oxide fuel cell (SOFC) interconnect materials. Four sets of interatomic potentials were developed and tested over the temperature range 0-1273 K. The predicted unit-cell volumes, elastic properties, volumetric shrinkage due to A-site doping of the ABO3 perovskite (La1-xCax)CrO3, defect-induced volumetric expansion due to reducing atmospheres, and thermal expansion were in reasonable agreement with experiment, though not all concurrently with a single set of potentials. Potentials based either on simple oxides or on partial charge models appeared to give the best overall predictions. Additional experimental data are needed to improve the potentials.

  20. Pressurized electrolysis stack with thermal expansion capability

    Science.gov (United States)

    Bourgeois, Richard Scott

    2015-07-14

    The present techniques provide systems and methods for mounting an electrolyzer stack in an outer shell so as to allow for differential thermal expansion of the electrolyzer stack and shell. Generally, an electrolyzer stack may be formed from a material with a high coefficient of thermal expansion, while the shell may be formed from a material having a lower coefficient of thermal expansion. The differences between the coefficients of thermal expansion may lead to damage to the electrolyzer stack as the shell may restrain the thermal expansion of the electrolyzer stack. To allow for the differences in thermal expansion, the electrolyzer stack may be mounted within the shell leaving a space between the electrolyzer stack and shell. The space between the electrolyzer stack and the shell may be filled with a non-conductive fluid to further equalize pressure inside and outside of the electrolyzer stack.

  1. Thermal expansion and structural distortion of perovskite — data for NaMgF 3 perovskite. Part I

    Science.gov (United States)

    Zhao, Yusheng; Weidner, Donald J.; Parise, John B.; Cox, David E.

    1993-02-01

    The crystal structure of NaMgF 3 perovskite (Neighborite) has been studied at high temperature by X-ray powder diffraction. Data were collected using a position sensitive detector with a monochromatic synchroton radiation source. Changes in unit cell and atomic positions of the perovskite structure were defined using the Rietveld refinement technique. The linear and volumetric thermal expansion coefficients are observed to be αa = 4.04 × 10 -5 K -1, αb = 1.53 × 10 -5 K -1, αc = 3.06 × 10 -5 K -1, αv = 8.80 × 10 -5 K -1 for the orthorhombic Pbnm phase, and αa0 = 3.16 × 10 -5 K -1, αv0 = 9.49 × 10 -5 K -1 for the cubic Pm3m phase of NaMgF 3 perovskite, respectively. The temperature-induced linear and volumetric changes of the centrosymmetrically distorted ABX 3 perovskite structure can be empirically expressed as a combination of the change of the (BX) bond length and the change of tilting of the BX 6 octahedral framework. The considerable anisotropy of linear thermal expansion, αa > αc > αb, for the orthorhombic Pbnm phase reflects the progressive decrease of structural distortion and the development of the phase transition of the NaMgF 3 perovskite. The tilting angle of the MgF 6 octahedral framework is observed to decrease rapidly toward zero as the temperature approaches Tc = 765°C in the manner expected for a ferroelastic phase transition. More interestingly, the apparent (MgF) bond lengths of the MgF 6 octahedra shrink dramatically throughout a temperature interval of about 100°C before the phase transition. The volumetric thermal expansion increases drastically in a critical manner as the temperature approaches Tc.

  2. Thermal Expansion of Irradiated Polytetrafluoroethylene

    OpenAIRE

    Subrahmanyam, HN; Subramanyam, SV

    1987-01-01

    The thermal expansion coefficient of gamma-irradiated Polytetrafluoroethylene (PTFE) has been measured in the temperature range 80-340 K by using a three-terminal capacitance technique. The samples are irradiated in air at room temperature with gamma rays from a $Co^{60}$ source at a dose rate of 0.26 Mrad/h. The change in crystallinity is measured by an x-ray technique. The expansion coefficient is found to increase with radiation dose below 140 K owing to the predominant effect of degradati...

  3. Mathematical Model Defining Volumetric Losses of Hydraulic Oil Compression in a Variable Capacity Displacement Pump

    Directory of Open Access Journals (Sweden)

    Paszota Zygmunt

    2015-01-01

    Full Text Available The objective of the work is to develop the capability of evaluating the volumetric losses of hydraulic oil compression in the working chambers of high pressure variable capacity displacement pump. Volumetric losses of oil compression must be determined as functions of the same parameters, which the volumetric losses due to leakage, resulting from the quality of design solution of the pump, are evaluated as dependent on and also as function of the oil aeration coefficient Ɛ. A mathematical model has been developed describing the hydraulic oil compressibility coefficient klc|Δppi;Ɛ;v as a relation to the ratio ΔpPi/pn of indicated increase ΔpPi of pressure in the working chambers and the nominal pressure pn, to the pump capacity coefficient bP, to the oil aeration coefficient  and to the ratio v/vnof oil viscosity v and reference viscosity vn. A mathematical model is presented of volumetric losses qpvc|ΔpPi;bp;;vof hydraulic oil compression in the pump working chambers in the form allowing to use it in the model of power of losses and energy efficiency

  4. Mass transfer coefficients in a hanson mixer-settler extraction column

    Directory of Open Access Journals (Sweden)

    M. Torab-Mostaedi

    2008-09-01

    Full Text Available The volumetric overall mass transfer coefficients in a pilot plant Hanson mixer-settler extraction column of seven stages have been measured using toluene-acetone-water system. The effects of agitation speed and dispersed and continuous phases flow rates on volumetric overall mass transfer coefficients have been investigated. The results show that the volumetric overall mass transfer coefficient increases with increase in agitation speed and reaches a maximum. After having reached its maximum, it falls with further increase in agitation speed. It was found that the volumetric overall mass transfer coefficient increases with increase in dispersed phase flow rate, while it decreases with increase in continuous phase flow rate. By using interfacial area, the overall mass transfer coefficients for continuous and dispersed phases are determined from volumetric coefficients. An empirical correlation for prediction of the continuous phase overall mass transfer coefficient is proposed in terms of Sherwood and Reynolds numbers. Also the experimental data of the column investigated are compared with data for various extraction columns. Comparison between theoretical models and experimental results for the dispersed phase mass transfer coefficient shows that these models do not have enough accuracy for column design. Using effective diffusivity in the Gröber equation results in more accurate prediction of overall mass transfer coefficient. The prediction of overall mass transfer coefficients from the presented equations is in good agreement with experimental results.

  5. Expansive Cements

    Science.gov (United States)

    1970-10-01

    sale: is disributici is unlimited = F’)RIWRD Seior Ignacio Soto, Rrecutive President, Instituto Mexicano del Cementc y Concreto , invited Mr. Bryant... Concreto , a.c., Kwidco, D. F., Mexico. Based on info.mation largely obtained from ACT Committee 223, Expansive ’ement. Concretes, ACI Journal, August 1Q70

  6. Reentrant Structural and Optical Properties and Large Positive Thermal Expansion in Perovskite Formamidinium Lead Iodide.

    Science.gov (United States)

    Fabini, Douglas H; Stoumpos, Constantinos C; Laurita, Geneva; Kaltzoglou, Andreas; Kontos, Athanassios G; Falaras, Polycarpos; Kanatzidis, Mercouri G; Seshadri, Ram

    2016-12-05

    The structure of the hybrid perovskite HC(NH2 )2 PbI3 (formamidinium lead iodide) reflects competing interactions associated with molecular motion, hydrogen bonding tendencies, thermally activated soft octahedral rotations, and the propensity for the Pb(2+) lone pair to express its stereochemistry. High-resolution synchrotron X-ray powder diffraction reveals a continuous transition from the cubic α-phase (Pm3‾ m, #221) to a tetragonal β-phase (P4/mbm, #127) at around 285 K, followed by a first-order transition to a tetragonal γ-phase (retaining P4/mbm, #127) at 140 K. An unusual reentrant pseudosymmetry in the β-to-γ phase transition is seen that is also reflected in the photoluminescence. Around room temperature, the coefficient of volumetric thermal expansion is among the largest for any extended crystalline solid.

  7. A new low-expansion nonflammable printed circuit board

    Science.gov (United States)

    Kennedy, B. W.

    1970-01-01

    Printed circuit board has a thermal coefficient of expansion similar to that of the electronic component leads. High-expansion composite materials are sandwiched between the outer layers of copper and woven fiber glass.

  8. Negative thermal expansion materials: technological key for control of thermal expansion

    OpenAIRE

    Koshi Takenaka

    2012-01-01

    Most materials expand upon heating. However, although rare, some materials contract upon heating. Such negative thermal expansion (NTE) materials have enormous industrial merit because they can control the thermal expansion of materials. Recent progress in materials research enables us to obtain materials exhibiting negative coefficients of linear thermal expansion over −30 ppm K−1. Such giant NTE is opening a new phase of control of thermal expansion in composites. Specifically examining pra...

  9. Surfactant enhanced volumetric sweep efficiency

    Energy Technology Data Exchange (ETDEWEB)

    Harwell, J.H.; Scamehorn, J.F.

    1989-10-01

    Surfactant-enhanced waterflooding is a novel EOR method aimed to improve the volumetric sweep efficiencies in reservoirs. The technique depends upon the ability to induce phase changes in surfactant solutions by mixing with surfactants of opposite charge or with salts of appropriate type. One surfactant or salt solution is injected into the reservoir. It is followed later by injection of another surfactant or salt solution. The sequence of injections is arranged so that the two solutions do not mix until they are into the permeable regions well away from the well bore. When they mix at this point, by design they form a precipitate or gel-like coacervate phase, plugging this permeable region, forcing flow through less permeable regions of the reservoir, improving sweep efficiency. The selectivity of the plugging process is demonstrated by achieving permeability reductions in the high permeable regions of Berea sandstone cores. Strategies were set to obtain a better control over the plug placement and the stability of plugs. A numerical simulator has been developed to investigate the potential increases in oil production of model systems. Furthermore, the hardness tolerance of anionic surfactant solutions is shown to be enhanced by addition of monovalent electrolyte or nonionic surfactants. 34 refs., 32 figs., 8 tabs.

  10. Conformal expansions and renormalons

    CERN Document Server

    Gardi, E; Gardi, Einan; Grunberg, Georges

    2001-01-01

    The large-order behaviour of QCD is dominated by renormalons. On the other hand renormalons do not occur in conformal theories, such as the one describing the infrared fixed-point of QCD at small beta_0 (the Banks--Zaks limit). Since the fixed-point has a perturbative realization, all-order perturbative relations exist between the conformal coefficients, which are renormalon-free, and the standard perturbative coefficients, which contain renormalons. Therefore, an explicit cancellation of renormalons should occur in these relations. The absence of renormalons in the conformal limit can thus be seen as a constraint on the structure of the QCD perturbative expansion. We show that the conformal constraint is non-trivial: a generic model for the large-order behaviour violates it. We also analyse a specific example, based on a renormalon-type integral over the two-loop running-coupling, where the required cancellation does occur.

  11. Colossal negative thermal expansion with an extended temperature interval covering room temperature in fine-powdered Mn0.98CoGe

    Science.gov (United States)

    Lin, Jianchao; Tong, Peng; Zhang, Kui; Tong, Haiyun; Guo, Xinge; Yang, Cheng; Wu, Ying; Wang, Meng; Lin, Shuai; Chen, Li; Song, Wenhai; Sun, Yuping

    2016-12-01

    MnM'X (M' = Co, Ni; X = Ge, Si, etc.) alloys usually present a large volumetric change during the Martensitic (MA) transformation. This offers a great opportunity for exploring new negative thermal expansion (NTE) materials if the temperature interval of NTE can be extended. Here, we report colossal NTE in fine-powdered Mn0.98CoGe prepared by repeated thermal cycling (TC) through the MA transition or ball milling. Both treatments can expand the MA transformation, and thus broaden the NTE temperature window (ΔT). For the powders that have gone through TC for ten times, ΔT reaches 90 K (309 K-399 K), and the linear expansion coefficient (αL) is about -141 ppm/K, which rank among the largest values of colossal NTE materials. The difference between two kinds of treatments and the possible mechanisms of the extended MA transformation window are discussed based on the introduced strain.

  12. Spatially uniform microflows induced by thermoviscous expansion along a traveling temperature wave: Analogies with electro-osmotic transport

    Science.gov (United States)

    Pal, Debashis; Chakraborty, Suman

    2012-07-01

    We discover that thermoviscous expansion along a traveling wave in a microfluidic channel may be capable of generating a spatially uniform flow profile in a time-averaged sense. We further delineate that the resultant complex flow characteristics, realized by virtue of an intricate interplay between thermal compression-expansion waves and temperature-dependent viscosity variations and controlled by an external heating, may be remarkably characterized by a unique thermal penetration depth scale (analogous to Debye length in electro-osmosis) and a velocity scale (analogous to the Helmholtz Smulochowski velocity in electro-osmosis) that in turn depends on the considerations of “thin” and “thick” microchannel limits, as dictated by the thermal penetration depth as compared to the lateral extent of the microfluidic channel. We show that, when the thermal penetration depth is small as compared to the channel height, a uniform velocity profile is generated in the channel in a time-averaged sense. The velocity scale characterizing this uniform flow may be represented by a function of the thermal diffusivity, volumetric expansion coefficient and thermal viscosity coefficient of the fluid, characteristic amplitude and speed of the thermal wave, as well as the channel height. Results from the present study are expected to provide valuable insights towards arresting hydrodynamic dispersion in microchannels by nonelectrochemical means, following a pH-independent route.

  13. Laser Based 3D Volumetric Display System

    Science.gov (United States)

    1993-03-01

    Literature, Costa Mesa, CA July 1983. 3. "A Real Time Autostereoscopic Multiplanar 3D Display System", Rodney Don Williams, Felix Garcia, Jr., Texas...8217 .- NUMBERS LASER BASED 3D VOLUMETRIC DISPLAY SYSTEM PR: CD13 0. AUTHOR(S) PE: N/AWIU: DN303151 P. Soltan, J. Trias, W. Robinson, W. Dahlke 7...laser generated 3D volumetric images on a rotating double helix, (where the 3D displays are computer controlled for group viewing with the naked eye

  14. Hydration and Thermal Expansion in Anatase Nanoparticles.

    Science.gov (United States)

    Zhu, He; Li, Qiang; Ren, Yang; Fan, Longlong; Chen, Jun; Deng, Jinxia; Xing, Xianran

    2016-08-01

    A tunable thermal expansion is reported in nanosized anatase by taking advantage of surface hydration. The coefficient of thermal expansion of 4 nm TiO2 along a-axis is negative with a hydrated surface and is positive without a hydrated surface. High-energy synchrotron X-ray pair distribution function analysis combined with ab initio calculations on the specific hydrated surface are carried out to reveal the local structure distortion that is responsible for the unusual negative thermal expansion.

  15. Hydration and Thermal Expansion in Anatase Nanoparticles

    Energy Technology Data Exchange (ETDEWEB)

    Zhu, He [Department of Physical Chemistry, University of Science and Technology Beijing, Beijing 100083 China; Li, Qiang [Department of Physical Chemistry, University of Science and Technology Beijing, Beijing 100083 China; Ren, Yang [Argonne National Laboratory, X-Ray Science Division, Argonne IL 60439 USA; Fan, Longlong [Department of Physical Chemistry, University of Science and Technology Beijing, Beijing 100083 China; Chen, Jun [Department of Physical Chemistry, University of Science and Technology Beijing, Beijing 100083 China; Deng, Jinxia [Department of Physical Chemistry, University of Science and Technology Beijing, Beijing 100083 China; Xing, Xianran [Department of Physical Chemistry, University of Science and Technology Beijing, Beijing 100083 China

    2016-06-06

    A tunable thermal expansion is reported in nanosized anatase by taking advantage of surface hydration. The coefficient of thermal expansion of 4 nm TiO2 along a-axis is negative with a hydrated surface and is positive without a hydrated surface. High-energy synchrotron X-ray pair distribution function analysis combined with ab initio calculations on the specific hydrated surface are carried out to reveal the local structure distortion that is responsible for the unusual negative thermal expansion.

  16. Design of materials with extreme thermal expansion using a three-phase topology optimization method

    DEFF Research Database (Denmark)

    Sigmund, Ole; Torquato, S.

    1997-01-01

    Composites with extremal or unusual thermal expansion coefficients are designed using a three-phase topology optimization method. The composites are made of two different material phases and a void phase. The topology optimization method consists in finding the distribution of material phases...... materials having maximum directional thermal expansion (thermal actuators), zero isotropic thermal expansion, and negative isotropic thermal expansion. It is shown that materials with effective negative thermal expansion coefficients can be obtained by mixing two phases with positive thermal expansion...

  17. Gas-Liquid Mass Transfer Coefficient in Stirred Tank Reactors

    NARCIS (Netherlands)

    Yawalkar, Archis A.; Heesink, Albertus B.M.; Versteeg, Geert F.; Pangarkar, Vishwas G.

    2002-01-01

    Volumetric gas—liquid mass transfer coefficient (kLa) data available in the literature for larger tanks (T = 0.39 m to 2.7 m) have been analyzed on the basis of relative dispersion parameter, N/Ncd. It was observed that at a given superficial gas velocity (VG), kLa values were approximately the same

  18. Gas–Liquid Mass Transfer Coefficient in Stirred Tank Reactors

    NARCIS (Netherlands)

    Yawalkar, Archis A.; Heesink, Albertus B.M.; Versteeg, Geert F.; Pangarkar, Vishwas G.

    2002-01-01

    Volumetric gas–liquid mass transfer coefficient (kLa) data available in the literature for larger tanks (T = 0.39 m to 2.7 m) have been analyzed on the basis of relative dispersion parameter, N/Ncd. It was observed that at a given superficial gas velocity (VG), kLa values were approximately the same

  19. Effect of core-shell polymer particles on the coefficient of thermal expansion of epoxy resin%核壳聚合物粒子对环氧树脂热膨胀系数的影响

    Institute of Scientific and Technical Information of China (English)

    赫玉欣; 张丽; 朱伸兵; 姚大虎; 张志强; 张玉清

    2012-01-01

    The epoxy resins were modified by core-shell polymer(CSP) particles.The effect of CSP on the coefficient of thermal expansion(CTE) of modified epoxy resins was investigated by infrared spectroscopy,thermal mechanical analysis and scanning electron microscopy.The results showed that hydrogen bond was formed between C= =O of CSP particle shell and — OH of DGEBA epoxy resin side chain during the curing pocess,thereby strengthening the interface role of core-shell polymer particles and epoxy matrix.The glass transition temperatures of CSP particles modified epoxy resin were decreased and CTE values of modified resin below the Tg range were decreased,then increased compared with that of neat epoxy resins with the increasing of CSP content.The CTE of the resins with 0.5% CSP was decreased by 12.88%.But the CTE values of modified resins were all higher than that of neat epoxy resins above the Tg range.%采用核壳聚合物(Core-Shell Polymer,CSP)粒子改性环氧树脂,通过红外光谱、热力学分析和扫描电镜研究了CSP粒子对环氧树脂基体热膨胀系数(CTE)的影响。结果表明:CSP粒子壳材料分子链中的羰基在环氧树脂固化过程中可与环氧分子侧链上的羟基形成氢键作用,从而加强了核壳聚合物粒子与环氧树脂的界面作用。随着CSP粒子质量分数的增加,改性环氧树脂基体的玻璃化转变温度呈下降趋势;相对于纯环氧树脂,改性环氧树脂在玻璃化转变温度下的CTE呈现先下降后上升的趋势,添加质量分数为0.5%的CSP后,其CTE值降低了12.88%。但在玻璃化转变温度上的热膨胀系数均高于纯环氧树脂。

  20. Synthesis and evaluation of effective parameters in thermal expansion coefficient of Ln0.6Sr0.4Co0.2M0.8O3− (Ln = La,Nd and M = Mn,Fe) perovskite oxide

    Indian Academy of Sciences (India)

    Fatemeh Heydari; Amir Maghsoudipour; Masoud Alizadeh; Zahra Khakpour; Masoumeh Javaheri

    2015-08-01

    In this study, oxides Ln0.6Sr0.4Co0.2M0.8O3− (Ln = La,Nd and M = Mn,Fe) have been prepared and characterized to study the influence of the different cations on thermal expansion coefficient (TEC). TEC decreases favourably with replacement of Nd3+ and Mn3+ ions in the lattice. Nd3+ leads to decreasing ionicity of the Ln–O bond and phase transition from rhombohedral to orthorhombic. Structural parameters of compounds have been determined by X-ray diffraction (XRD). FT-IR analysis has been used to compare the bond strength of different cations in the lattice. Variations of lattice parameters of compounds have been monitored by in-situ XRD at different temperatures in order to study the thermo-chemical expansivity. Concentration of oxide ion vacancy has been determined by high temperature gravimetry. The results show more stability of Mn4+ ions in high temperature in comparison with Fe4+ ions, which suppreses the tendency to lose oxygen from the lattice with the increase in temperature.

  1. DIFFERENCE SCHEMES BASING ON COEFFICIENT APPROXIMATION

    Institute of Scientific and Technical Information of China (English)

    MOU Zong-ze; LONG Yong-xing; QU Wen-xiao

    2005-01-01

    In respect of variable coefficient differential equations, the equations of coefficient function approximation were more accurate than the coefficient to be frozen as a constant in every discrete subinterval. Usually, the difference schemes constructed based on Taylor expansion approximation of the solution do not suit the solution with sharp function.Introducing into local bases to be combined with coefficient function approximation, the difference can well depict more complex physical phenomena, for example, boundary layer as well as high oscillatory, with sharp behavior. The numerical test shows the method is more effective than the traditional one.

  2. Evolutionarily Conserved Pattern of Interactions in a Protein Revealed by Local Thermal Expansion Properties.

    Science.gov (United States)

    Dellarole, Mariano; Caro, Jose A; Roche, Julien; Fossat, Martin; Barthe, Philippe; García-Moreno E, Bertrand; Royer, Catherine A; Roumestand, Christian

    2015-07-29

    The way in which the network of intramolecular interactions determines the cooperative folding and conformational dynamics of a protein remains poorly understood. High-pressure NMR spectroscopy is uniquely suited to examine this problem because it combines the site-specific resolution of the NMR experiments with the local character of pressure perturbations. Here we report on the temperature dependence of the site-specific volumetric properties of various forms of staphylococcal nuclease (SNase), including three variants with engineered internal cavities, as measured with high-pressure NMR spectroscopy. The strong temperature dependence of pressure-induced unfolding arises from poorly understood differences in thermal expansion between the folded and unfolded states. A significant inverse correlation was observed between the global thermal expansion of the folded proteins and the number of strong intramolecular hydrogen bonds, as determined by the temperature coefficient of the backbone amide chemical shifts. Comparison of the identity of these strong H-bonds with the co-evolution of pairs of residues in the SNase protein family suggests that the architecture of the interactions detected in the NMR experiments could be linked to a functional aspect of the protein. Moreover, the temperature dependence of the residue-specific volume changes of unfolding yielded residue-specific differences in expansivity and revealed how mutations impact intramolecular interaction patterns. These results show that intramolecular interactions in the folded states of proteins impose constraints against thermal expansion and that, hence, knowledge of site-specific thermal expansivity offers insight into the patterns of strong intramolecular interactions and other local determinants of protein stability, cooperativity, and potentially also of function.

  3. Volumetric response classification in metastatic solid tumors on MSCT: Initial results in a whole-body setting

    Energy Technology Data Exchange (ETDEWEB)

    Wulff, A.M., E-mail: a.wulff@rad.uni-kiel.de [Klinik für Diagnostische Radiologie, Arnold-Heller-Straße 3, Haus 23, 24105 Kiel (Germany); Fabel, M. [Klinik für Diagnostische Radiologie, Arnold-Heller-Straße 3, Haus 23, 24105 Kiel (Germany); Freitag-Wolf, S., E-mail: freitag@medinfo.uni-kiel.de [Institut für Medizinische Informatik und Statistik, Brunswiker Str. 10, 24105 Kiel (Germany); Tepper, M., E-mail: m.tepper@rad.uni-kiel.de [Klinik für Diagnostische Radiologie, Arnold-Heller-Straße 3, Haus 23, 24105 Kiel (Germany); Knabe, H.M., E-mail: h.knabe@rad.uni-kiel.de [Klinik für Diagnostische Radiologie, Arnold-Heller-Straße 3, Haus 23, 24105 Kiel (Germany); Schäfer, J.P., E-mail: jp.schaefer@rad.uni-kiel.de [Klinik für Diagnostische Radiologie, Arnold-Heller-Straße 3, Haus 23, 24105 Kiel (Germany); Jansen, O., E-mail: o.jansen@neurorad.uni-kiel.de [Klinik für Diagnostische Radiologie, Arnold-Heller-Straße 3, Haus 23, 24105 Kiel (Germany); Bolte, H., E-mail: hendrik.bolte@ukmuenster.de [Klinik für Nuklearmedizin, Albert-Schweitzer-Campus 1, Gebäude A1, 48149 Münster (Germany)

    2013-10-01

    Purpose: To examine technical parameters of measurement accuracy and differences in tumor response classification using RECIST 1.1 and volumetric assessment in three common metastasis types (lung nodules, liver lesions, lymph node metastasis) simultaneously. Materials and methods: 56 consecutive patients (32 female) aged 41–82 years with a wide range of metastatic solid tumors were examined with MSCT for baseline and follow up. Images were evaluated by three experienced radiologists using manual measurements and semi-automatic lesion segmentation. Institutional ethics review was obtained and all patients gave written informed consent. Data analysis comprised interobserver variability operationalized as coefficient of variation and categorical response classification according to RECIST 1.1 for both manual and volumetric measures. Continuous data were assessed for statistical significance with Wilcoxon signed-rank test and categorical data with Fleiss kappa. Results: Interobserver variability was 6.3% (IQR 4.6%) for manual and 4.1% (IQR 4.4%) for volumetrically obtained sum of relevant diameters (p < 0.05, corrected). 4–8 patients’ response to therapy was classified differently across observers by using volumetry compared to standard manual measurements. Fleiss kappa revealed no significant difference in categorical agreement of response classification between manual (0.7558) and volumetric (0.7623) measurements. Conclusion: Under standard RECIST thresholds there was no advantage of volumetric compared to manual response evaluation. However volumetric assessment yielded significantly lower interobserver variability. This may allow narrower thresholds for volumetric response classification in the future.

  4. Volumetric properties of sunflower methyl ester oil at high pressure.

    Science.gov (United States)

    Aparicio, Cristina; Guignon, Bérengère; Rodríguez-Antón, Luis M; Sanz, Pedro D

    2007-09-01

    Biodiesel is an alternative to diesel oil (DO), because it is a fuel obtained from renewable resources that has lower emissions than DO. Biomass production should promote agricultural activity to obtain fuels for the transport sector. The study of the behavior of biodiesel at varying pressure and temperature is very interesting because diesel engines are mechanical systems that work with fuels submitted to high pressure. The specific volume, isothermal compressibility, and cubic expansion coefficients of refined sunflower methyl ester oil (SMEO) and unrefined sunflower methyl ester oil (URSMEO) were obtained and compared with those of DO from 0.1 to 350 MPa and 288.15 to 328.15 K. This work shows that oil refinement did not significantly modify any of the properties studied of the final biodiesel. Compared with DO, both SMEOs were about 6% denser, whereas isothermal compressibility and cubic expansion coefficients were bigger or smaller for DO depending on pressure and temperature.

  5. Origami Metamaterials for Tunable Thermal Expansion.

    Science.gov (United States)

    Boatti, Elisa; Vasios, Nikolaos; Bertoldi, Katia

    2017-07-01

    Materials with engineered thermal expansion, capable of achieving targeted area/volume changes in response to variations in temperature, are important for a number of aerospace, optical, energy, and microelectronic applications. While most of the proposed structures with engineered coefficient of thermal expansion consist of bi-material 2D or 3D lattices, here it is shown that origami metamaterials also provide a platform for the design of systems with a wide range of thermal expansion coefficients. Experiments and simulations are combined to demonstrate that by tuning the geometrical parameters of the origami structure and the arrangement of plates and creases, an extremely broad range of thermal expansion coefficients can be obtained. Differently from all previously reported systems, the proposed structure is tunable in situ and nonporous. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  6. Asymptotic expansions for high-contrast linear elasticity

    KAUST Repository

    Poveda, Leonardo A.

    2015-03-01

    We study linear elasticity problems with high contrast in the coefficients using asymptotic limits recently introduced. We derive an asymptotic expansion to solve heterogeneous elasticity problems in terms of the contrast in the coefficients. We study the convergence of the expansion in the H1 norm. © 2015 Elsevier B.V.

  7. Influence of Cobb Angle and ISIS2 Surface Topography Volumetric Asymmetry on Scoliosis Research Society-22 Outcome Scores in Scoliosis.

    Science.gov (United States)

    Brewer, Paul; Berryman, Fiona; Baker, De; Pynsent, Paul; Gardner, Adrian

    2013-11-01

    Retrospective sequential patient series. To establish the relationship between the magnitude of the deformity in scoliosis and patients' perception of their condition, as measured with Scoliosis Research Society-22 scores. A total of 93 untreated patients with adolescent idiopathic scoliosis were included retrospectively. The Cobb angle was measured from a plain radiograph, and volumetric asymmetry was measured by ISIS2 surface topography. The association between Scoliosis Research Society scores for function, pain, self-image, and mental health against Cobb angle and volumetric asymmetry was investigated using the Pearson correlation coefficient. Correlation of both Cobb angle and volumetric asymmetry with function and pain was weak (all self-image, was higher, although still moderate (-.37 for Cobb angle and -.44 for volumetric asymmetry). Both were statistically significant (Cobb angle, p = .0002; volumetric asymmetry; p = .00001). Cobb angle contributed 13.8% to the linear relationship with self-image, whereas volumetric asymmetry contributed 19.3%. For mental health, correlation was statistically significant with Cobb angle (p = .011) and volumetric asymmetry (p = .0005), but the correlation was low to moderate (-.26 and -.35, respectively). Cobb angle contributed 6.9% to the linear relationship with mental health, whereas volumetric asymmetry contributed 12.4%. Volumetric asymmetry correlates better with both mental health and self-image compared with Cobb angle, but the correlation was only moderate. This study suggests that a patient's own perception of self-image and mental health is multifactorial and not completely explained through present objective measurements of the size of the deformity. This helps to explain the difficulties in any objective analysis of a problem with multifactorial perception issues. Further study is required to investigate other physical aspects of the deformity that may have a role in how patients view themselves. Copyright

  8. Nonequilibrium volumetric response of shocked polymers

    Energy Technology Data Exchange (ETDEWEB)

    Clements, B E [Los Alamos National Laboratory

    2009-01-01

    Polymers are well known for their non-equilibrium deviatoric behavior. However, investigations involving both high rate shock experiments and equilibrium measured thermodynamic quantities remind us that the volumetric behavior also exhibits a non-equilibrium response. Experiments supporting the notion of a non-equilibrium volumetric behavior will be summarized. Following that discussion, a continuum-level theory is proposed that will account for both the equilibrium and non-equilibrium response. Upon finding agreement with experiment, the theory is used to study the relaxation of a shocked polymer back towards its shocked equilibrium state.

  9. Chemical Expansion: Implications for Electrochemical Energy Storage and Conversion Devices

    DEFF Research Database (Denmark)

    Bishop, S.R.; Marrocchelli, D.; Chatzichristodoulou, Christodoulos

    2014-01-01

    Many energy-related materials rely on the uptake and release of large quantities of ions, for example, Li+ in batteries, H+ in hydrogen storage materials, and O2− in solid-oxide fuel cell and related materials. These compositional changes often result in large volumetric dilation of the material...... modeling and an overview of factors impacting chemical expansion. We discuss the implications of chemical expansion for mechanical stability and functionality in the energy applications above, as well as in other oxide-based systems. The use of chemical expansion as a new means to probe other materials...... properties, as well as its contribution to recently investigated electromechanical coupling, is also highlighted....

  10. Electrical Resistance Alloys and Low-Expansion Alloys

    DEFF Research Database (Denmark)

    Kjer, Torben

    1996-01-01

    The article gives an overview of electrical resistance alloys and alloys with low thermal expansion. The electrical resistance alloys comprise resistance alloys, heating alloys and thermostat alloys. The low expansion alloys comprise alloys with very low expansion coefficients, alloys with very low...

  11. Re-evaluation of experimental data on the second virial coefficient for steam and development of its analytical representation as a function of the internal energy

    Directory of Open Access Journals (Sweden)

    Hrubý J.

    2013-04-01

    Full Text Available A re-evaluation of the second virial coefficient of steam is presented in the paper. The work is a part of broader effort to develop a formulation of the properties of dry and metastable steam suitable for CFD computations. The re-evaluation follows up previous work by Harvey and Lemmon [1], however with a special care for the lower temperature region close to the triple point and including more experimental data. The second virial coefficient was evaluated from volumetric (pvT data, calorimetric measurements for saturated vapor, steam expansion experiments (measurements of the Joule–Thomson coefficient and the isothermal throttling coefficient and measurements of the speed of sound. To accurately evaluate the uncertainty of calorimetric measurements, the uncertainty of the temperature derivative of the saturation pressure was determined based on refitting of the IAPWS saturation pressure formula to the experimental data. In the second step, the evaluated data and their uncertainties were used to develop an analytical formula to compute the second virial coefficient as function of internal energy in a range corresponding to the ideal-gas temperatures from 273.16 K to 1073.15 K. The choice of internal energy and density as independent variables is required for the CFD computations to avoid time-consuming iterations.

  12. Re-evaluation of experimental data on the second virial coefficient for steam and development of its analytical representation as a function of the internal energy

    Science.gov (United States)

    Duška, M.; Hrubý, J.

    2013-04-01

    A re-evaluation of the second virial coefficient of steam is presented in the paper. The work is a part of broader effort to develop a formulation of the properties of dry and metastable steam suitable for CFD computations. The re-evaluation follows up previous work by Harvey and Lemmon [1], however with a special care for the lower temperature region close to the triple point and including more experimental data. The second virial coefficient was evaluated from volumetric (pvT) data, calorimetric measurements for saturated vapor, steam expansion experiments (measurements of the Joule-Thomson coefficient and the isothermal throttling coefficient) and measurements of the speed of sound. To accurately evaluate the uncertainty of calorimetric measurements, the uncertainty of the temperature derivative of the saturation pressure was determined based on refitting of the IAPWS saturation pressure formula to the experimental data. In the second step, the evaluated data and their uncertainties were used to develop an analytical formula to compute the second virial coefficient as function of internal energy in a range corresponding to the ideal-gas temperatures from 273.16 K to 1073.15 K. The choice of internal energy and density as independent variables is required for the CFD computations to avoid time-consuming iterations.

  13. Expansive Soil Crack Depth under Cumulative Damage

    Directory of Open Access Journals (Sweden)

    Bei-xiao Shi

    2014-01-01

    Full Text Available The crack developing depth is a key problem to slope stability of the expansive soil and its project governance and the crack appears under the roles of dry-wet cycle and gradually develops. It is believed from the analysis that, because of its own cohesion, the expansive soil will have a certain amount of deformation under pulling stress but without cracks. The soil body will crack only when the deformation exceeds the ultimate tensile strain that causes cracks. And it is also believed that, due to the combined effect of various environmental factors, particularly changes of the internal water content, the inherent basic physical properties of expansive soil are weakened, and irreversible cumulative damages are eventually formed, resulting in the development of expansive soil cracks in depth. Starting from the perspective of volumetric strain that is caused by water loss, considering the influences of water loss rate and dry-wet cycle on crack developing depth, the crack developing depth calculation model which considers the water loss rate and the cumulative damages is established. Both the proposal of water loss rate and the application of cumulative damage theory to the expansive soil crack development problems try to avoid difficulties in matrix suction measurement, which will surely play a good role in promoting and improving the research of unsaturated expansive soil.

  14. Operator product expansion algebra

    Energy Technology Data Exchange (ETDEWEB)

    Holland, Jan [School of Mathematics, Cardiff University, Senghennydd Rd, Cardiff CF24 4AG (United Kingdom); Hollands, Stefan [School of Mathematics, Cardiff University, Senghennydd Rd, Cardiff CF24 4AG (United Kingdom); Institut für Theoretische Physik, Universität Leipzig, Brüderstr. 16, Leipzig, D-04103 (Germany)

    2013-07-15

    We establish conceptually important properties of the operator product expansion (OPE) in the context of perturbative, Euclidean φ{sup 4}-quantum field theory. First, we demonstrate, generalizing earlier results and techniques of hep-th/1105.3375, that the 3-point OPE, =Σ{sub C}C{sub A{sub 1A{sub 2A{sub 3}{sup C}}}}, usually interpreted only as an asymptotic short distance expansion, actually converges at finite, and even large, distances. We further show that the factorization identity C{sub A{sub 1A{sub 2A{sub 3}{sup B}}}}=Σ{sub C}C{sub A{sub 1A{sub 2}{sup C}}}C{sub CA{sub 3}{sup B}} is satisfied for suitable configurations of the spacetime arguments. Again, the infinite sum is shown to be convergent. Our proofs rely on explicit bounds on the remainders of these expansions, obtained using refined versions, mostly due to Kopper et al., of the renormalization group flow equation method. These bounds also establish that each OPE coefficient is a real analytic function in the spacetime arguments for non-coinciding points. Our results hold for arbitrary but finite loop orders. They lend support to proposals for a general axiomatic framework of quantum field theory, based on such “consistency conditions” and akin to vertex operator algebras, wherein the OPE is promoted to the defining structure of the theory.

  15. Process conditions and volumetric composition in composites

    DEFF Research Database (Denmark)

    Madsen, Bo

    2013-01-01

    The obtainable volumetric composition in composites is linked to the gravimetric composition, and it is influenced by the conditions of the manufacturing process. A model for the volumetric composition is presented, where the volume fractions of fibers, matrix and porosity are calculated as a fun...... is increased. Altogether, the model is demonstrated to be a valuable tool for a quantitative analysis of the effect of process conditions. Based on the presented findings and considerations, examples of future work are mentioned for the further improvement of the model.......The obtainable volumetric composition in composites is linked to the gravimetric composition, and it is influenced by the conditions of the manufacturing process. A model for the volumetric composition is presented, where the volume fractions of fibers, matrix and porosity are calculated...... as a function of the fiber weight fraction, and where parameters are included for the composite microstructure, and the fiber assembly compaction behavior. Based on experimental data of composites manufactured with different process conditions, together with model predictions, different types of process related...

  16. Indexing Volumetric Shapes with Matching and Packing.

    Science.gov (United States)

    Koes, David Ryan; Camacho, Carlos J

    2015-04-01

    We describe a novel algorithm for bulk-loading an index with high-dimensional data and apply it to the problem of volumetric shape matching. Our matching and packing algorithm is a general approach for packing data according to a similarity metric. First an approximate k-nearest neighbor graph is constructed using vantage-point initialization, an improvement to previous work that decreases construction time while improving the quality of approximation. Then graph matching is iteratively performed to pack related items closely together. The end result is a dense index with good performance. We define a new query specification for shape matching that uses minimum and maximum shape constraints to explicitly specify the spatial requirements of the desired shape. This specification provides a natural language for performing volumetric shape matching and is readily supported by the geometry-based similarity search (GSS) tree, an indexing structure that maintains explicit representations of volumetric shape. We describe our implementation of a GSS tree for volumetric shape matching and provide a comprehensive evaluation of parameter sensitivity, performance, and scalability. Compared to previous bulk-loading algorithms, we find that matching and packing can construct a GSS-tree index in the same amount of time that is denser, flatter, and better performing, with an observed average performance improvement of 2X.

  17. Effective Expansion: Balance between Shrinkage and Hygroscopic Expansion.

    Science.gov (United States)

    Suiter, E A; Watson, L E; Tantbirojn, D; Lou, J S B; Versluis, A

    2016-05-01

    The purpose of this study was to investigate the relationship between hygroscopic expansion and polymerization shrinkage for compensation of polymerization shrinkage stresses in a restored tooth. One resin-modified glass-ionomer (RMGI) (Ketac Nano, 3M ESPE), 2 compomers (Dyract, Dentsply; Compoglass, Ivoclar), and a universal resin-based composite (Esthet•X HD, Dentsply) were tested. Volumetric change after polymerization ("total shrinkage") and during 4 wk of water storage at 37°C was measured using an optical method (n= 10). Post-gel shrinkage was measured during polymerization using a strain gauge method (n= 10). Extracted human molars with large mesio-occluso-distal slot preparations were restored with the tested restorative materials. Tooth surfaces at baseline (preparation), after restoration, and during 4 wk of 37°C water storage were scanned with an optical scanner to determine cuspal flexure (n= 8). Occlusal interface integrity was measured using dye penetration. Data were analyzed using analysis of variance and post hoc tests (significance level 0.05). All tested materials shrunk after polymerization. RMGI had the highest total shrinkage (4.65%) but lowest post-gel shrinkage (0.35%). Shrinkage values dropped significantly during storage in water but had not completely compensated polymerization shrinkage after 4 wk. All restored teeth initially exhibited inward (negative) cuspal flexure due to polymerization shrinkage. Cuspal flexure with the RMGI restoration was significantly less (-6.4 µm) than with the other materials (-12.1 to -14.1 µm). After 1 d, cuspal flexure reversed to +5.0 µm cuspal expansion with the RMGI and increased to +9.3 µm at 4 wk. After 4 wk, hygroscopic expansion compensated cuspal flexure in a compomer (Compoglass) and reduced flexure with Dyract and resin-based composite. Marginal integrity (93.7% intact restoration wall) was best for the Compoglass restorations and lowest (73.1%) for the RMGI restorations. Hygroscopic

  18. Novel thermal expansion of lead titanate

    Institute of Scientific and Technical Information of China (English)

    XING Xianran; DENG Jinxia; CHEN Jun; LIU Guirong

    2003-01-01

    Lattice parameters of lead titanate were precisely re-determined in the ternperature range of-150-950℃ by high precision XRPD measurements. It was clarified that there was no any evidence for a new phase transition at low temperatures. Tetragonal distortion strain decreases with temperature increasing. A novel thermal expansion was observed, positive thermal expansion from-150℃ to room temperature (RT) and above 490℃, and the negative thermal expansion in the temperature range of RT-490℃. A big jump of thermal expansion coefficient is attributed to the tetragonal-cubic phase transition. A rationalization for the negative thermal expansion of PbTiO3 is due to the decrease of anion-anion repulsion as polyhedra become more regular at heating. The mechanisms of positive and negative thermal expansions were elucidated as the same nature in the homogenous tetragonal phase at present case.

  19. Thermal expansion of layered cobaltites Y(Ba{sub 1-x}Sr{sub x})Co{sub 2}O{sub 5+{delta}} with x = 0, 0.05 and 0.10

    Energy Technology Data Exchange (ETDEWEB)

    Aurelio, G; Bustingorry, S; Sanchez, R D [Consejo Nacional de Investigaciones CientIficas y Tecnicas, Centro Atomico Bariloche-Comision Nacional de EnergIa Atomica, Av. Bustillo 9500, 8400 S. C. de Bariloche, RN (Argentina); Cuello, G J, E-mail: gaurelio@cab.cnea.gov.ar [Institut Laue-Langevin, F-38042 Grenoble (France)

    2011-08-10

    The crystal structure and thermal expansion of Sr-doped layered cobaltites Y(Ba{sub 1-x}Sr{sub x})Co{sub 2}O{sub 5+{delta}} (x = 0, 0.05 and 0.10) were studied by means of in situ neutron thermodiffraction in the temperature range 20 K {<=} T {<=} 570 K. The evolution with temperature of lattice parameters for the phases which crystallize in this system is presented, as well as their dependence on the oxygen non-stoichiometry {delta}. Each phase's volume has been fitted using available models based on the Grueneisen approximation to the zero-pressure equation of state and using the Ruffa model based on the Morse potential, both using a Debye model for the internal energy. The coefficient of volumetric thermal expansion, Debye temperature and other thermodynamic parameters are presented and compared with other perovskite compounds.

  20. Brain stem and cerebellum volumetric analysis of Machado Joseph disease patients

    Directory of Open Access Journals (Sweden)

    S T Camargos

    2011-01-01

    Full Text Available Machado-Joseph disease, or spinocerebellar ataxia type 3(MJD/SCA3, is the most frequent late onset spinocerebellar ataxia and results from a CAG repeat expansion in the ataxin-3 gene. Previous studies have found correlation between atrophy of cerebellum and brainstem with age and CAG repeats, although no such correlation has been found with disease duration and clinical manifestations. In this study we test the hypothesis that atrophy of cerebellum and brainstem in MJD/SCA3 is related to clinical severity, disease duration and CAG repeat length as well as to other variables such as age and ICARS (International Cooperative Ataxia Rating Scale. Whole brain high resolution MRI and volumetric measurement with cranial volume normalization were obtained from 15 MJD/SCA3 patients and 15 normal, age and sex-matchedcontrols. We applied ICARS and compared the score with volumes and CAG number, disease duration and age. We found significant correlation of both brain stem and cerebellar atrophy with CAG repeat length, age, disease duration and degree of disability. The Spearman rank correlation was stronger with volumetric reduction of the cerebellum than with brain stem. Our data allow us to conclude that volumetric analysis might reveal progressive degeneration after disease onset, which in turn is linked to both age and number of CAG repeat expansions in SCA 3.

  1. Expansion and Shrinkage Coefficient of Crystal Face Distance of the MC Nylon and MC Nylon/ZnO Nanocomposites%MC尼龙和MC尼龙/纳米ZnO复合材料晶面间距的膨胀系数和收缩系数

    Institute of Scientific and Technical Information of China (English)

    周莉; 田彦文

    2011-01-01

    MC nylon/ZnO nanocomposite was prepared by in-situ polymerization and analyzed by the dynamic high temperature X-ray diffraction(XRD). Changes of interplanar (crystal) spacing between α1 (200) and α2 (002 + 202 )and thermal stability of crystal structure in war ming and cooling process were in research. The results show that α1 and α2 of MC nylon shrink and expand respectively as the temperature increases, and reverse as the temperature decreases. The thermal expansion coefficient of the lattice planes of MC nylon is αa1T = - 1.45515 × 10-4℃ -1 and αa2T = 4.03985 × 10-4 °C- 1 and the shrinkage coefficient of the lattice planes of MC nylon isβa1T = -2. 53341 × 10-4℃ -1 and βa2T = 3.77188 × 10-4℃-1. The thermal expansion coefficients of MC nylon/ZnO nanocomposites is αa1T 1. 45984 × 10-4℃ - 1 andαT-α2 - 3.18063 × 10-4℃ - 1 and the shrinkage coefficient of the lattice planes of MC nylon/ZnO nanocomposites isβa1T = - 1.23801 × 10-4℃ -1 and βa2T = 2.98470 × 10-4℃ -1 It can be concluded that the addition of nano-ZnO reduces the sensitivity of MC nylon to the temperature, and enhances the thermal stability of MC nylon.%采用原位聚合反应制备铸型(MC)尼龙6/纳米ZnO复合材料,并用动态高温X射线衍射(XRD)法对合成的MC尼龙/纳米ZnO复合材料进行研究,考察其在升温和降温过程中α和α晶面间距的变化、结晶结构的热稳定性.结果表明,随着温度的升高,MC尼龙的α(200)和α(002+202)晶面分别发生了收缩和膨胀,降温过程中分别为膨胀和收缩.纯Mc尼龙在升温过程中晶面的线膨胀系数为α>=-1.45515×10℃、α>=4.03985×10℃;降温过程中晶面的线收缩系数为β>=-2.53341×10℃、β>=3.77188×10℃.MC尼龙/纳米ZnO复合材料在升温过程中α和α晶面的线膨胀系数为α>=-1.45984×10℃、α>=3.18063×10℃;降温过程中α和α晶面的线收缩系数为β>=-1.23801×10℃、β>=2.98470×10℃.可见,纳米ZnO的加入,使MC尼

  2. Infinite matrices, wavelet coefficients and frames

    Directory of Open Access Journals (Sweden)

    N. A. Sheikh

    2004-01-01

    Full Text Available We study the action of A on f∈L2(ℝ and on its wavelet coefficients, where A=(almjklmjk is a double infinite matrix. We find the frame condition for A-transform of f∈L2(ℝ whose wavelet series expansion is known.

  3. Structure, phase transition, and controllable thermal expansion behaviors of Sc(2-x)Fe(x)Mo₃O₁₂.

    Science.gov (United States)

    Wu, Meimei; Liu, Xinzhi; Chen, Dongfeng; Huang, Qingzhen; Wu, Hui; Liu, Yuntao

    2014-09-02

    The crystal structures, phase transition, and thermal expansion behaviors of solid solutions of Sc(2-x)Fe(x)Mo3O12 (0 ≤ x ≤ 2) have been examined using X-ray diffraction (XRD), neutron powder diffraction (NPD), and differential scanning calorimetry (DSC). At room temperature, samples crystallize in a single orthorhombic structure for the compositions of x thermal expansion, and the volumetric coefficients of thermal expansion derived from XRD and NPD are 0.28 × 10(-6) °C(-1) (250-800 °C) and 0.65 × 10(-6) °C(-1) (227-427 °C), respectively. NPD results of Sc2Mo3O12 (x = 0) and Sc(1.3)Fe(0.7)Mo3O12 (x = 0.7) indicate that Fe substitution for Sc induces reduction of the mean Sc(Fe)-Mo nonbond distance and the different thermal variations of Sc(Fe)-O5-Mo2 and Sc(Fe)-O3-Mo2 bond angles. The correlation between the displacements of oxygen atoms and the variation of unit cell parameters was investigated in detail for Sc2Mo3O12.

  4. Influence of the filler content on the thermal expansion behavior of an epoxy matrix particulate composite

    Energy Technology Data Exchange (ETDEWEB)

    Tognana, S. [IFIMAT - Universidad Nacional del Centro de la Provincia de Buenos Aires, Pinto 399, B7000GHG Tandil (Argentina); Consejo Nacional de Investigaciones Cientificas y Tecnicas (Argentina); Salgueiro, W. [IFIMAT - Universidad Nacional del Centro de la Provincia de Buenos Aires, Pinto 399, B7000GHG Tandil (Argentina); Somoza, A. [IFIMAT - Universidad Nacional del Centro de la Provincia de Buenos Aires, Pinto 399, B7000GHG Tandil (Argentina); Comision de Investigaciones Cientificas de la Provincia de Buenos Aires (Argentina)], E-mail: asomoza@exa.unicen.edu.ar; Pomarico, J.A.; Ranea-Sandoval, H.F. [Consejo Nacional de Investigaciones Cientificas y Tecnicas (Argentina); IFAS - Universidad Nacional del Centro de la Provincia de Buenos Aires, Pinto 399, B7000GHG Tandil (Argentina)

    2009-02-15

    The thermal expansion behavior of epoxy matrix particulate composites prepared with different volumetric filler contents ({phi}) up to 25 vol.% was studied. Using a very simple absolute optical dilatometer developed in our laboratory, the coefficients of thermal expansion (CTE) for pure epoxy resin matrix and the composites in the glassy and rubbery states (293 K {<=} T {<=} 493 K) were obtained. For the matrix, the CTE obtained in the two states are in good agreement with those reported. For composites the results are discussed into the frame of different approaches using well-known mechanical models. In the glassy state, the CTE behavior could be well described by the upper bound of the Hashin-Shtrikman model. In the rubbery state it was necessary to evaluate the contribution of the average volume of nanoholes in the epoxy matrix as a consequence of the addition of particles. To this aim, using positron annihilation lifetime spectroscopy, the dependence of the average volume of nanoholes with {phi} was measured.

  5. Two-dimensional and volumetric airway changes after bimaxillary surgery for class III malocclusion.

    Science.gov (United States)

    Vaezi, Toraj; Zarch, Seyed Hossein Hosseini; Eshghpour, Majid; Kermani, Hamed

    2017-04-01

    Any change in maxilla and mandible position can alter the upper airway, and any decrease in the upper airway can cause sleep disorders. Thus, it is necessary to assess airway changes after repositioning of the maxilla and mandible during orthognathic surgery. The purpose of this study was to evaluate linear and volumetric changes in the upper airway after bimaxillary surgery to correct class III malocclusion via cone-beam computed tomography (CBCT) and to identify correlations between linear and volumetric changes. This was a prospective cohort study. CBCTs from 10 class III patients were evaluated before surgery and three months after. The Wilcoxon one-sample test was used to evaluate the differences in measurements before and after surgery. Spearman's rank correlation coefficient was used to test the correlation between linear and volumetric changes. The results show that the nasopharyngeal space increased significantly, and that this increase correlated with degree of maxillary advancement. No significant changes were found in volumes before and after surgery. A correlation was found between linear and volumetric oropharyngeal changes. Bimaxillary surgical correction of class III malocclusion did not cause statistically significant changes in the posterior airway space.

  6. Negative thermal expansion materials: technological key for control of thermal expansion.

    Science.gov (United States)

    Takenaka, Koshi

    2012-02-01

    Most materials expand upon heating. However, although rare, some materials contract upon heating. Such negative thermal expansion (NTE) materials have enormous industrial merit because they can control the thermal expansion of materials. Recent progress in materials research enables us to obtain materials exhibiting negative coefficients of linear thermal expansion over -30 ppm K(-1). Such giant NTE is opening a new phase of control of thermal expansion in composites. Specifically examining practical aspects, this review briefly summarizes materials and mechanisms of NTE as well as composites containing NTE materials, based mainly on activities of the last decade.

  7. Combined surface and volumetric occlusion shading

    KAUST Repository

    Schott, Matthias O.

    2012-02-01

    In this paper, a method for interactive direct volume rendering is proposed that computes ambient occlusion effects for visualizations that combine both volumetric and geometric primitives, specifically tube shaped geometric objects representing streamlines, magnetic field lines or DTI fiber tracts. The proposed algorithm extends the recently proposed Directional Occlusion Shading model to allow the rendering of those geometric shapes in combination with a context providing 3D volume, considering mutual occlusion between structures represented by a volume or geometry. © 2012 IEEE.

  8. Buoyancy Driven Mixing with Continuous Volumetric Energy Deposition

    Science.gov (United States)

    Wachtor, Adam J.; Jebrail, Farzaneh F.; Dennisen, Nicholas A.; Andrews, Malcolm J.; Gore, Robert A.

    2014-11-01

    An experiment involving a miscible fluid pair is presented which transitioned from a Rayleigh-Taylor (RT) stable to RT unstable configuration through continuous volumetric energy deposition (VED) by microwave radiation. Initially a light, low microwave absorbing fluid rested above a heavier, more absorbing fluid. The alignment of the density gradient with gravity made the system stable, and the Atwood number (At) for the initial setup was approximately -0.12. Exposing the fluid pair to microwave radiation preferentially heated the bottom fluid, and caused its density to drop due to thermal expansion. As heating of the bottom fluid continued, the At varied from negative to positive, and after the system passed through the neutral stability point, At = 0, buoyancy driven mixing ensued. Continuous VED caused the At to continue increasing and further drive the mixing process. Successful VED mixing required careful design of the fluid pair used in the experiment. Therefore, fluid selection is discussed, along with challenges and limitations of data collection using the experimental microwave facility. Experimental and model predictions of the neutral stability point, and onset of buoyancy driven mixing, are compared, and differences with classical, constant At RT driven turbulence are discussed.

  9. Effects of Different Reconstruction Parameters on CT Volumetric Measurement 
of Pulmonary Nodules

    Directory of Open Access Journals (Sweden)

    Rongrong YANG

    2012-02-01

    Full Text Available Background and objective It has been proven that volumetric measurements could detect subtle changes in small pulmonary nodules in serial CT scans, and thus may play an important role in the follow-up of indeterminate pulmonary nodules and in differentiating malignant nodules from benign nodules. The current study aims to evaluate the effects of different reconstruction parameters on the volumetric measurements of pulmonary nodules in chest CT scans. Methods Thirty subjects who underwent chest CT scan because of indeterminate pulmonary nodules in General Hospital of Tianjin Medical University from December 2009 to August 2011 were retrospectively analyzed. A total of 52 pulmonary nodules were included, and all CT data were reconstructed using three reconstruction algorithms and three slice thicknesses. The volumetric measurements of the nodules were performed using the advanced lung analysis (ALA software. The effects of the reconstruction algorithms, slice thicknesses, and nodule diameters on the volumetric measurements were assessed using the multivariate analysis of variance for repeated measures, the correlation analysis, and the Bland-Altman method. Results The reconstruction algorithms (F=13.6, P<0.001 and slice thicknesses (F=4.4, P=0.02 had significant effects on the measured volume of pulmonary nodules. In addition, the coefficients of variation of nine measurements were inversely related with nodule diameter (r=-0.814, P<0.001. The volume measured at the 2.5 mm slice thickness had poor agreement with the volumes measured at 1.25 mm and 0.625 mm, respectively. Moreover, the best agreement was achieved between the slice thicknesses of 1.25 mm and 0.625 mm using the bone algorithm. Conclusion Reconstruction algorithms and slice thicknesses have significant impacts on the volumetric measurements of lung nodules, especially for the small nodules. Therefore, the reconstruction setting in serial CT scans should be consistent in the follow

  10. Wave Reflection Coefficient Spectrum

    Institute of Scientific and Technical Information of China (English)

    俞聿修; 邵利民; 柳淑学

    2003-01-01

    The wave reflection coefficient frequency spectrum and directional spectrum for concrete face slope breakwaters and rubble mound breakwaters are investigated through physical model tests in the present study. The reflection coefficients of oblique irregular waves are analyzed by the Modified Two-Point Method (MTPM) proposed by the authors. The results show that the wave reflection coefficient decreases with increasing wave frequency and incident angle or decreasing structure slope. The reflection coefficient frequency spectrum and its variation with Iribarren number are given in this paper. The paper also suggests an empirical 3-dimensional reflection coefficient spectrum, i.e. reflection coefficient directional spectrum, which can be used to illustrate quantitatively the variation of reflection coefficient with the incident angle and the Iribarren number for oblique irregular waves.

  11. Comparison of experimental methods for determination of the volumetric mass transfer coefficient in fermentation processes

    Science.gov (United States)

    Tobajas, M.; García-Calvo, E.

    Mass transfer in bioreactors has been examined. In the present work, dynamic methods are used for the determination of KLa values for water, model media and a fermentation broth (Candida utilis) in an airlift reactor. The conventional dynamic method is applied at the end of the microbial process in order to avoid an alteration in the metabolism of the microorganisms. New dynamic methods are used to determine KLa in an airlift reactor during the microbial growth of Candida utilis on glucose. One of the methods is based on the continuous measurement of carbon dioxide production while the other method is based on the relationship between the oxygen transfer and biomass growth rates. These methods of determining KLa does not interfere with the microorganisms action. A theoretical mass transfer model has been used for KLa estimation for the systems described above. Some differences between calculated and measured values are found for fermentation processes due to the model is developed for two-phase air-water systems. Nevertheless, the average deviation between the predicted values and those obtained from the relationship between oxygen transfer and biomass production rates are lower than 25% in any case.

  12. Anisotropy in Thermo-Optic Coefficient of Different Polymer Systems by Attenuated Total Reflection Configuration

    Institute of Scientific and Technical Information of China (English)

    LI Xiang; CAO Zhuang-Qi; SHEN Qi-Shun; MENG Qing-Hua; HUANG De-Ying; GUO Kun-Peng; QIU Ling; SHEN Yu-Quan

    2006-01-01

    @@ Thermo-optic coefficient dn/dT as well as volume expansion coefficients β of different polymer systems are measured for both TE and TM polarizations in an attenuated total reflection (ATR) configuration. Experimental results indicate that cross-linked polymer systems exhibit the thermal expansion coefficients smaller than those of the original side-chain systems. Moreover, the anisotropies in thermo-optic coefficients of the polymer systems with small birefringence exhibit linear relationship with the anisotropies in volume expansion coefficients, but the polymer systems with larger birefringence exhibit more complicated relationship.

  13. Supercongruences satisfied by coefficients of 2F1 hypergeometric series

    CERN Document Server

    Chan, Heng Huat; Krattenthaler, Christian; Osburn, Robert

    2009-01-01

    Recently, Chan, Cooper and Sica conjectured two congruences for coefficients of classical 2F1 hypergeometric series which also arise from power series expansions of modular forms in terms of modular functions. We prove these two congruences using combinatorial properties of the coefficients.

  14. Volumetric polymerization shrinkage of contemporary composite resins

    Directory of Open Access Journals (Sweden)

    Halim Nagem Filho

    2007-10-01

    Full Text Available The polymerization shrinkage of composite resins may affect negatively the clinical outcome of the restoration. Extensive research has been carried out to develop new formulations of composite resins in order to provide good handling characteristics and some dimensional stability during polymerization. The purpose of this study was to analyze, in vitro, the magnitude of the volumetric polymerization shrinkage of 7 contemporary composite resins (Definite, Suprafill, SureFil, Filtek Z250, Fill Magic, Alert, and Solitaire to determine whether there are differences among these materials. The tests were conducted with precision of 0.1 mg. The volumetric shrinkage was measured by hydrostatic weighing before and after polymerization and calculated by known mathematical equations. One-way ANOVA (a or = 0.05 was used to determine statistically significant differences in volumetric shrinkage among the tested composite resins. Suprafill (1.87±0.01 and Definite (1.89±0.01 shrank significantly less than the other composite resins. SureFil (2.01±0.06, Filtek Z250 (1.99±0.03, and Fill Magic (2.02±0.02 presented intermediate levels of polymerization shrinkage. Alert and Solitaire presented the highest degree of polymerization shrinkage. Knowing the polymerization shrinkage rates of the commercially available composite resins, the dentist would be able to choose between using composite resins with lower polymerization shrinkage rates or adopting technical or operational procedures to minimize the adverse effects deriving from resin contraction during light-activation.

  15. A SUBDIVISION SCHEME FOR VOLUMETRIC MODELS

    Institute of Scientific and Technical Information of China (English)

    GhulamMustafa; LiuXuefeng

    2005-01-01

    In this paper, a subdivision scheme which generalizes a surface scheme in previous papers to volume meshes is designed. The scheme exhibits significant control over shrink-age/size of volumetric models. It also has the ability to conveniently incorporate boundaries and creases into a smooth limit shape of models. The method presented here is much simpler and easier as compared to MacCracken and Joy's. This method makes no restrictions on the local topology of meshes. Particularly, it can be applied without any change to meshes of nonmanifold topology.

  16. Volumetric composition in composites and historical data

    DEFF Research Database (Denmark)

    Lilholt, Hans; Madsen, Bo

    2013-01-01

    guidance to the optimal combination of fibre content, matrix content and porosity content, in order to achieve the best obtainable properties. Several composite materials systems have been shown to be handleable with this model. An extensive series of experimental data for the system of cellulose fibres...... and polymer (resin) was produced in 1942 – 1944, and these data have been (re-)analysed by the volumetric composition model, and the property values for density, stiffness and strength have been evaluated. Good agreement has been obtained and some further observations have been extracted from the analysis....

  17. IMITATION OF STANDARD VOLUMETRIC ACTIVITY METAL SAMPLES

    Directory of Open Access Journals (Sweden)

    A. I. Zhukouski

    2016-01-01

    Full Text Available Due to the specific character of problems in the field of ionizing radiation spectroscopy, the R&D and making process of standard volumetric activity metal samples (standard samples for calibration and verification of spectrometric equipment is not only expensive, but also requires the use of highly qualified experts and a unique specific equipment. Theoretical and experimental studies performed have shown the possibility to use imitators as a set of alternating point sources of gamma radiation and metal plates and their use along with standard volumetric activity metal samples for calibration of scintillation-based detectors used in radiation control in metallurgy. Response functions or instrumental spectra of such spectrometer to radionuclides like 137Cs, 134Cs, 152Eu, 154Eu, 60Co, 54Mn, 232Th, 226Ra, 65Zn, 125Sb+125mTe, 106Ru+106Rh, 94Nb, 110mAg, 233U, 234U, 235U and 238U are required for calibration in a given measurement geometry. Standard samples in the form of a probe made of melt metal of a certain diameter and height are used in such measurements. However, the production of reference materials is costly and even problematic for such radionuclides as 94Nb, 125Sb+125mTe, 234U, 235U  etc. A recognized solution to solve this problem is to use the Monte-Carlo simulation method. Instrumental experimental and theoretical spectra obtained by using standard samples and their imitators show a high compliance between experimental spectra of real samples and the theoretical ones of their Monte-Carlo models, between spectra of real samples and the ones of their imitators and finally, between experimental spectra of real sample imitators and the theoretical ones of their Monte-Carlo models. They also have shown the adequacy and consistency of the approach in using a combination of metal scattering layers and reference point gamma-ray sources instead of standard volumetric activity metal samples. As for using several reference point gamma-ray sources

  18. Magnetic volumetric hologram memory with magnetic garnet.

    Science.gov (United States)

    Nakamura, Yuichi; Takagi, Hiroyuki; Lim, Pang Boey; Inoue, Mitsuteru

    2014-06-30

    Holographic memory is a promising next-generation optical memory that has a higher recording density and a higher transfer rate than other types of memory. In holographic memory, magnetic garnet films can serve as rewritable holographic memory media by use of magneto-optical effect. We have now demonstrated that a magnetic hologram can be recorded volumetrically in a ferromagnetic garnet film and that the signal image can be reconstructed from it for the first time. In addition, multiplicity of the magnetic hologram was also confirmed; the image could be reconstructed from a spot overlapped by other spots.

  19. Heat capacity and thermal expansion of water and helium

    Science.gov (United States)

    Putintsev, N. M.; Putintsev, D. N.

    2017-04-01

    Original expressions for heat capacity CV and its components, vibrational and configurational components of thermal expansion coefficient were established. The values of CV, Cvib, Cconf, αvib and αconf for water and helium 4He were calculated.

  20. Towards finite density QCD with Taylor expansions

    CERN Document Server

    Karsch, Frithjof; Wagner, Mathias; Wambach, Jochen

    2011-01-01

    We analyze general convergence properties of the Taylor expansion of observables to finite chemical potential in the framework of an effective 2+1 flavor Polyakov-quark-meson model. To compute the required higher order coefficients a novel technique based on algorithmic differentiation has been developed. Results for thermodynamic observables as well as the phase structure obtained through the series expansion up to 24th order are compared to the full model solution at finite chemical potential. The available higher order coefficients also allow for resummations, e.g. Pade series, which improve the convergence behavior. In view of our results we discuss the prospects for locating the QCD phase boundary and a possible critical endpoint with the Taylor expansion method.

  1. Thermal expansion of doped lanthanum gallates

    Indian Academy of Sciences (India)

    K T Jacob; S Jain; V S Saji; P V K Srikanth

    2010-08-01

    Thermal expansion of several compositions of Sr and Mg-doped LaGaO3 including an -site deficient composition (La0.9Sr0.1)0.98(Ga0.8Mg0.2)O2.821 were measured in the temperature range from 298 to 1273 K. The effect of doping on thermal expansion was studied by varying the composition at one site of the perovskite structure (either or ), while keeping the composition at the other site invariant. Thermal expansion varied nonlinearly with temperature and exhibited an inflexion between 550 and 620 K, probably related to the change in crystal structure from orthorhombic to rhombohedral. The dependence of average thermal expansion coefficient (av) on the dopant concentration on either or site of the perovskite structure was found to be linear, when the composition at the other site was kept constant. Mg doping on the -site had a greater effect on the average thermal expansion coefficient than Sr doping on the -site. Cation deficiency at the -site decreases thermal expansion when compositions at both sites are held constant.

  2. Heterodiffusion coefficients in alpha-iron

    Energy Technology Data Exchange (ETDEWEB)

    Katsika-Tsigourakou, Vassiliki, E-mail: vkatsik@phys.uoa.g [Department of Solid State Physics, Faculty of Physics, University of Athens, Panepistimiopolis Zografos, 15784 Athens (Greece); Skordas, Efthimios S. [Department of Solid State Physics, Faculty of Physics, University of Athens, Panepistimiopolis Zografos, 15784 Athens (Greece)

    2010-04-01

    The diffusion of tungsten in alpha-iron is important for the application of ferritic-iron alloys to thermal power plants. These data, over a wide temperature range across the Curie temperature, have been recently reported. We show that these diffusion coefficients can be satisfactory reproduced in terms of the bulk elastic and expansivity data by means of a thermodynamical model that interconnects point defects parameters with bulk qualities.

  3. Metal-Ion Additives Reduce Thermal Expansion Of Polyimides

    Science.gov (United States)

    Stoakley, Diane M.; St. Clair, Anne K.; Emerson, Burt R., Jr.; Willis, George L.

    1994-01-01

    Polyimides widely used as high-performance polymers because of their excellent thermal stability and toughness. However, their coefficients of thermal expansion (CTE's) greater than those of metals, ceramics, and glasses. Decreasing CTE's of polyimides increase usefulness for aerospace and electronics applications in which dimensional stability required. Additives containing metal ions reduce coefficients of thermal expansion of polyimides. Reductions range from 11 to over 100 percent.

  4. Thermal expansion of spinel-type Si3N4

    DEFF Research Database (Denmark)

    Paszkowics, W.; Minkikayev, R.; Piszora, P.

    2004-01-01

    The lattice parameter and thermal expansion coefficient (TEC) for the spinel-type Si3N4 phase prepared under high-pressure and high-temperature conditions are determined for 14 K......The lattice parameter and thermal expansion coefficient (TEC) for the spinel-type Si3N4 phase prepared under high-pressure and high-temperature conditions are determined for 14 K...

  5. Modified Biserial Correlation Coefficients.

    Science.gov (United States)

    Kraemer, Helena Chmura

    1981-01-01

    Asymptotic distribution theory of Brogden's form of biserial correlation coefficient is derived and large sample estimates of its standard error obtained. Its relative efficiency to the biserial correlation coefficient is examined. Recommendations for choice of estimator of biserial correlation are presented. (Author/JKS)

  6. On skin expansion.

    Science.gov (United States)

    Pamplona, Djenane C; Velloso, Raquel Q; Radwanski, Henrique N

    2014-01-01

    This article discusses skin expansion without considering cellular growth of the skin. An in vivo analysis was carried out that involved expansion at three different sites on one patient, allowing for the observation of the relaxation process. Those measurements were used to characterize the human skin of the thorax during the surgical process of skin expansion. A comparison between the in vivo results and the numerical finite elements model of the expansion was used to identify the material elastic parameters of the skin of the thorax of that patient. Delfino's constitutive equation was chosen to model the in vivo results. The skin is considered to be an isotropic, homogeneous, hyperelastic, and incompressible membrane. When the skin is extended, such as with expanders, the collagen fibers are also extended and cause stiffening in the skin, which results in increasing resistance to expansion or further stretching. We observed this phenomenon as an increase in the parameters as subsequent expansions continued. The number and shape of the skin expanders used in expansions were also studied, both mathematically and experimentally. The choice of the site where the expansion should be performed is discussed to enlighten problems that can lead to frustrated skin expansions. These results are very encouraging and provide insight into our understanding of the behavior of stretched skin by expansion. To our knowledge, this study has provided results that considerably improve our understanding of the behavior of human skin under expansion.

  7. The Thermal Expansion Of Feldspars

    Science.gov (United States)

    Hovis, G. L.; Medford, A.; Conlon, M.

    2009-12-01

    Hovis and others (1) investigated the thermal expansion of natural and synthetic AlSi3 feldspars and demonstrated that the coefficient of thermal expansion (α) decreases significantly, and linearly, with increasing room-temperature volume (VRT). In all such feldspars, therefore, chemical expansion limits thermal expansion. The scope of this work now has been broadened to include plagioclase and Ba-K feldspar crystalline solutions. X-ray powder diffraction data have been collected between room temperature and 925 °C on six plagioclase specimens ranging in composition from anorthite to oligoclase. When combined with thermal expansion data for albite (2,3,4) a steep linear trend of α as a function of VRT emerges, reflecting how small changes in composition dramatically affect expansion behavior. The thermal expansion data for five synthetic Ba-K feldspars ranging in composition from 20 to 100 mole percent celsian, combined with data for pure K-feldspar (3,4), show α-VRT relationships similar in nature to the plagioclase series, but with a slope and intercept different from the latter. Taken as a group all Al2Si2 feldspars, including anorthite and celsian from the present study along with Sr- (5) and Pb-feldspar (6) from other workers, show very limited thermal expansion that, unlike AlSi3 feldspars, has little dependence on the divalent-ion (or M-) site occupant. This apparently is due to the necessitated alternation of Al and Si in the tetrahedral sites of these minerals (7), which in turn locks the tetrahedral framework and makes the M-site occupant nearly irrelevant to expansion behavior. Indeed, in feldspar series with coupled chemical substitution it is the change away from a 1:1 Al:Si ratio that gives feldspars greater freedom to expand. Overall, the relationships among α, chemical composition, and room-temperature volume provide useful predictive tools for estimating feldspar thermal expansion and give insight into the controls of expansion behavior in

  8. Enhancing Volumetric Bouligand-Minkowski Fractal Descriptors by using Functional Data Analysis

    CERN Document Server

    Florindo, João Batista; Bruno, Odemir Martinez; 10.1142/S0129183111016701

    2012-01-01

    This work proposes and study the concept of Functional Data Analysis transform, applying it to the performance improving of volumetric Bouligand-Minkowski fractal descriptors. The proposed transform consists essentially in changing the descriptors originally defined in the space of the calculus of fractal dimension into the space of coefficients used in the functional data representation of these descriptors. The transformed decriptors are used here in texture classification problems. The enhancement provided by the FDA transform is measured by comparing the transformed to the original descriptors in terms of the correctness rate in the classification of well known datasets.

  9. Energy transfer, volumetric expansion, and removal of oral biofilms by non-contact brushing

    NARCIS (Netherlands)

    Busscher, H. J.; Jager, D.; Finger, G.; Schaefer, N.; van der Mei, H. C.

    2010-01-01

    Non-contact removal of oral biofilms offers advantages beyond the reach of bristles, but it is unknown how energy transfer for removal from brush-to-biofilm occurs. In the present study we evaluated non-contact, oral biofilm removal by oscillating-rotating and sonic toothbrushes, and their acoustic

  10. All Photons Imaging Through Volumetric Scattering

    Science.gov (United States)

    Satat, Guy; Heshmat, Barmak; Raviv, Dan; Raskar, Ramesh

    2016-01-01

    Imaging through thick highly scattering media (sample thickness ≫ mean free path) can realize broad applications in biomedical and industrial imaging as well as remote sensing. Here we propose a computational “All Photons Imaging” (API) framework that utilizes time-resolved measurement for imaging through thick volumetric scattering by using both early arrived (non-scattered) and diffused photons. As opposed to other methods which aim to lock on specific photons (coherent, ballistic, acoustically modulated, etc.), this framework aims to use all of the optical signal. Compared to conventional early photon measurements for imaging through a 15 mm tissue phantom, our method shows a two fold improvement in spatial resolution (4db increase in Peak SNR). This all optical, calibration-free framework enables widefield imaging through thick turbid media, and opens new avenues in non-invasive testing, analysis, and diagnosis. PMID:27683065

  11. A Technique for Volumetric CSG Based on Morphology

    DEFF Research Database (Denmark)

    Bærentzen, Jakob Andreas; Christensen, Niels Jørgen

    2001-01-01

    In this paper, a new technique for volumetric CSG is presented. The technique requires the input volumes to correspond to solids which fulfill a voxelization suitability criterion. Assume the CSG operation is union. The volumetric union of two such volumes is defined in terms of the voxelization...

  12. Transport Coefficients of Fluids

    CERN Document Server

    Eu, Byung Chan

    2006-01-01

    Until recently the formal statistical mechanical approach offered no practicable method for computing the transport coefficients of liquids, and so most practitioners had to resort to empirical fitting formulas. This has now changed, as demonstrated in this innovative monograph. The author presents and applies new methods based on statistical mechanics for calculating the transport coefficients of simple and complex liquids over wide ranges of density and temperature. These molecular theories enable the transport coefficients to be calculated in terms of equilibrium thermodynamic properties, and the results are shown to account satisfactorily for experimental observations, including even the non-Newtonian behavior of fluids far from equilibrium.

  13. Planning strategies in volumetric modulated are therapy for breast.

    Science.gov (United States)

    Giorgia, Nicolini; Antonella, Fogliata; Alessandro, Clivio; Eugenio, Vanetti; Luca, Cozzi

    2011-07-01

    In breast radiotherapy with intensity modulation, it is a well established practice to extend the dose fluence outside the limit of the body contour to account for small changes in size and position of the target and the rest of the tissues due to respiration or to possible oedema. A simple approach is not applicable with RapidArc volumetric modulated are therapy not being based on a fixed field fluence delivery. In this study, a viable technical strategy to account for this need is presented. RapidArc (RA) plans for six breast cancer patients (three right and three left cases), were optimized (PRO version III) on the original CT data set (0) and on an alternative CT (E) generated with an artificial expansion (and assignment of soft-tissue equivalent HU) of 10 mm of the body in the breast region and of the PTV contours toward the external direction. Final dose calculations for the two set of plans were performed on the same original CT data set O, normalizing the dose prescription (50 Gy) to the target mean. In this way, two treatment plans on the same CT set O for each patient were obtained: the no action plan (OO) and the alternative plan based on an expanded optimization (EO). Fixing MU, these two plans were then recomputed on the expanded CT data set and on an intermediate one (with expansion = 5 mm), to mimic, possible changes in size due to edema during treatment or residual displacements due to breathing not properly controlled. Aim of the study was to quantify the robustness of this planning strategy on dose distributions when either the OO or the EO strategies were adopted. For all the combinations, a DVH analysis of all involved structures is reported. I. The two optimization approaches gave comparable dose distributions on the original CT data set. II. When plans were evaluated on the expanded CTs (mimicking the presence of edema), the EO approach showed improved target coverage if compared to OO: on CT_10 mm, Dv = 98% [%]= 92.5 +/- 0.9 and 68.5 +/- 3

  14. Gas sorption and the consequent volumetric and permeability change of coal

    Science.gov (United States)

    Lin, Wenjuan

    in the injection gas, the greater the amount of total adsorption. Volumetric strain followed the same trend as the amount of adsorption with pressure and injection gas composition. Permeability showed opposite behaviors, decreasing with the increase of pressure and the percentage of CO2 in the injection gas. The experimental adsorption, volumetric strain, and permeability data were analyzed to investigate the numerical correlations between gas sorption, sorption-induced volumetric strain and permeability, and pressure and injection gas composition. The relationship between the amount of adsorption and pressure for pure gases (CO2 and N2) were readily represented by parametric isotherm models, such as Langmuir and the N-layer BET equations. Modeling efforts of multicomponent adsorption included predicting amount of adsorption and adsorbed phase composition based on the extended Langmuir equations and the ideal adsorbed solution model. Activity coefficients of the components in the adsorbed phase were computed based on the real adsorbed solution model and the ABC excess Gibbs free energy model. Algorithms for modeling the CO 2/N2-Coal system were developed, and the constraints and strength of each model were discussed. The experimental volumetric strain was found to be linearly proportional to the total amount of adsorption and independent of the injection gas composition. The permeability reduction could not be readily correlated by the models in the literature unless the change of other coal properties (bulk modulus, axial constrained modulus, etc.) due to gas sorption was incorporated. The sorption, volumetric strain, and permeability data collected in this study can be used for comparison by other researchers conducting similar studies. The algorithms of sorption modeling and the correlations developed in this study are readily incorporated into the simulation of enhanced coalbed methane recovery and CO2 sequestration in coalbeds. (Abstract shortened by UMI.)

  15. Ultrasound attenuation dependence on air compression or expansion processes

    NARCIS (Netherlands)

    Jakevicius, L.; Demcenko, A.; Mardosaite, R.

    2010-01-01

    In this work variation of ultrasonic attenuation coefficient is analyzed in terms of air compression or expansion processes. In closed spaces changing air volume, the ultrasound attenuation coefficient depends on thermodynamic processes which occur during the air volume change. Two limiting cases ar

  16. Asymptotic expansions for the Gaussian unitary ensemble

    DEFF Research Database (Denmark)

    Haagerup, Uffe; Thorbjørnsen, Steen

    2012-01-01

    Let g : R ¿ C be a C8-function with all derivatives bounded and let trn denote the normalized trace on the n × n matrices. In Ref. 3 Ercolani and McLaughlin established asymptotic expansions of the mean value ¿{trn(g(Xn))} for a rather general class of random matrices Xn, including the Gaussian...... Unitary Ensemble (GUE). Using an analytical approach, we provide in the present paper an alternative proof of this asymptotic expansion in the GUE case. Specifically we derive for a random matrix Xn that where k is an arbitrary positive integer. Considered as mappings of g, we determine the coefficients...

  17. Micro-architected Composite Lattices with Tunable Negative Thermal Expansions

    Science.gov (United States)

    Wang, Qiming

    Solid materials with minimum or negative thermal expansion (NTE) have broad applications, from dental fillings to thermal-sensitive precision instruments. Previous studies on NTE structures were mostly focused on theoretically design and 2D experimental demonstrations. Here, aided with multimaterial projection micro-stereolithography, we experimentally fabricate multi-material composite lattices that exhibit significant negative thermal expansion in three directions and over a large range of temperature variations. The negative thermal expansion is induced by the structural interaction of material components with distinct thermal expansion coefficients. The NTE performance can be tuned over a large range by varying the thermal expansion coefficient difference between constituent beams and geometrical arrangement. Our experimental results match qualitatively with a simple scaling law and quantitatively consistently with computational models.

  18. Optical property characterization of molten salt mixtures for thermal modeling of volumetrically absorbing solar receiver applications

    Science.gov (United States)

    Tetreault-Friend, Melanie; McKrell, Thomas; Baglietto, Emilio; Gil, Antoni; Slocum, Alexander H.; Calvet, Nicolas

    2017-06-01

    A method for experimentally determining the attenuation coefficient of high temperature semi-transparent liquids for volumetrically absorbing solar receiver applications was developed. The method was used to measure the attenuation coefficient over a broad spectral range in a 40 wt. % KNO3:60 wt. % NaNO3 binary nitrate molten salt mixture (solar salt). The measured absorption bands extend over 98% of the re-emission spectrum of the salt, indicating that thermal redistribution within the salt itself via radiative participating media effects is negligible. In addition, the effects of the salt's purity and thermal decomposition on the optical properties were also investigated and the light penetration depth is shown to vary significantly in the presence of impurities. The implications of these results for solar receiver design and modeling are discussed.

  19. Optimization of volumetric breast density estimation in digital mammograms.

    Science.gov (United States)

    Holland, Katharina; Gubern-Mérida, Albert; Mann, Ritse M; Karssemeijer, Nico

    2017-05-07

    Fibroglandular tissue volume and percent density can be estimated in unprocessed mammograms using a physics-based method, which relies on an internal reference value representing the projection of fat only. However, pixels representing fat only may not be present in dense breasts, causing an underestimation of density measurements. In this work, we investigate alternative approaches for obtaining a tissue reference value to improve density estimations, particularly in dense breasts. Two of three investigated reference values (F1, F2) are percentiles of the pixel value distribution in the breast interior (the contact area of breast and compression paddle). F1 is determined in a small breast interior, which minimizes the risk that peripheral pixels are included in the measurement at the cost of increasing the chance that no proper reference can be found. F2 is obtained using a larger breast interior. The new approach which is developed for very dense breasts does not require the presence of a fatty tissue region. As reference region we select the densest region in the mammogram and assume that this represents a projection of entirely dense tissue embedded between the subcutaneous fatty tissue layers. By measuring the thickness of the fat layers a reference (F3) can be computed. To obtain accurate breast density estimates irrespective of breast composition we investigated a combination of the results of the three reference values. We collected 202 pairs of MRI's and digital mammograms from 119 women. We compared the percent dense volume estimates based on both modalities and calculated Pearson's correlation coefficients. With the references F1-F3 we found respectively a correlation of [Formula: see text], [Formula: see text] and [Formula: see text]. Best results were obtained with the combination of the density estimations ([Formula: see text]). Results show that better volumetric density estimates can be obtained with the hybrid method, in particular for dense

  20. Soil volumetric water content measurements using TDR technique

    Directory of Open Access Journals (Sweden)

    S. Vincenzi

    1996-06-01

    Full Text Available A physical model to measure some hydrological and thermal parameters in soils will to be set up. The vertical profiles of: volumetric water content, matric potential and temperature will be monitored in different soils. The volumetric soil water content is measured by means of the Time Domain Reflectometry (TDR technique. The result of a test to determine experimentally the reproducibility of the volumetric water content measurements is reported together with the methodology and the results of the analysis of the TDR wave forms. The analysis is based on the calculation of the travel time of the TDR signal in the wave guide embedded in the soil.

  1. Iterative reconstruction of volumetric particle distribution

    Science.gov (United States)

    Wieneke, Bernhard

    2013-02-01

    For tracking the motion of illuminated particles in space and time several volumetric flow measurement techniques are available like 3D-particle tracking velocimetry (3D-PTV) recording images from typically three to four viewing directions. For higher seeding densities and the same experimental setup, tomographic PIV (Tomo-PIV) reconstructs voxel intensities using an iterative tomographic reconstruction algorithm (e.g. multiplicative algebraic reconstruction technique, MART) followed by cross-correlation of sub-volumes computing instantaneous 3D flow fields on a regular grid. A novel hybrid algorithm is proposed here that similar to MART iteratively reconstructs 3D-particle locations by comparing the recorded images with the projections calculated from the particle distribution in the volume. But like 3D-PTV, particles are represented by 3D-positions instead of voxel-based intensity blobs as in MART. Detailed knowledge of the optical transfer function and the particle image shape is mandatory, which may differ for different positions in the volume and for each camera. Using synthetic data it is shown that this method is capable of reconstructing densely seeded flows up to about 0.05 ppp with similar accuracy as Tomo-PIV. Finally the method is validated with experimental data.

  2. Lung, liver and lymph node metastases in follow-up MSCT. Comprehensive volumetric assessment of lesion size changes

    Energy Technology Data Exchange (ETDEWEB)

    Wulff, A.M.; Fischer, S.; Biederer, J.; Heller, M.; Fabel, M. [Universitaetsklinikum Schleswig-Holstein, Kiel (Germany). Klinik fuer Diagnostische Radiologie; Bolte, H. [Universitaetsklinikum Muenster (Germany). Klinik und Poliklinik fuer Nuklearmedizin; Freitag-Wolf, S. [Universitaetsklinikum Schleswig-Holstein, Kiel (Germany). Inst. fuer Medizinische Informatik und Statistik; Soza, G.; Tietjen, C. [Siemens AG (Germany). Imaging and IT Div. Computed Tomography

    2012-09-15

    Purpose: To investigate measurement accuracy in terms of precision and inter-rater variability in the simultaneous volumetric assessment of lung, liver and lymph node metastasis size change over time in comparison to RECIST 1.1. Materials and Methods: Three independent readers evaluated multislice CT data from clinical follow-up studies (chest/abdomen) in 50 patients with metastases. A total of 117 lung, 77 liver and 97 lymph node metastases were assessed manually (RECIST 1.1) and by volumetry with semi-automated software. The quality of segmentation and need for manual adjustments were recorded. Volumes were converted to effective diameters to allow comparison to RECIST. For statistical assessment of precision and interobserver agreement, the Wilcoxon-signed rank test and Bland-Altman plots were utilized. Results: The quality of segmentation after manual correction was acceptable to excellent in 95 % of lesions and manual corrections were applied in 21 - 36 % of all lesions, most predominantly in lymph nodes. Mean precision was 2.6 - 6.3 % (manual) with 0.2 - 1.5 % (effective) relative measurement deviation (p <.001). Inter-reader median variation coefficients ranged from 9.4 - 12.8 % (manual) and 2.9 - 8.2 % (volumetric) for different lesion types (p <.001). The limits of agreement were {+-} 9.8 to {+-} 11.2 % for volumetric assessment. Conclusion: Superior precision and inter-rater variability of volumetric over manual measurement of lesion change over time was demonstrated in a whole body setting. (orig.)

  3. Multidimensional extremal dependence coefficients

    OpenAIRE

    2017-01-01

    Extreme values modeling has attracting the attention of researchers in diverse areas such as the environment, engineering, or finance. Multivariate extreme value distributions are particularly suitable to model the tails of multidimensional phenomena. The analysis of the dependence among multivariate maxima is useful to evaluate risk. Here we present new multivariate extreme value models, as well as, coefficients to assess multivariate extremal dependence.

  4. Re-expansion method for circular waveguide discontinuities: Application to concentric expansion chambers

    Science.gov (United States)

    Homentcovschi, Dorel; Miles, Ronald N.

    2012-01-01

    The paper applies the re-expansion method for analyzing planar discontinuities at the junction of two axi-symmetrical circular waveguides. The normal modes in the two waveguides are expanded at the junction plane into a system of functions accounting for velocity singularities at the corner points. As the new expansion has a high convergence order, only a few terms have to be considered for obtaining the solution of most practical problems. This paper gives the equivalent impedance accounting for nonplanar waves into a plane-wave analysis and also the scattering matrix describing the coupling of arbitrary modes at each side of the discontinuity valid in the case of many propagating modes in both sides of the duct. The last section applies the re-expansion technique to some concentric expansion chambers providing an explicit formula for the transmission loss coefficient. PMID:22352491

  5. Correction of the volumetric effect in a 2D-array of ionisation chambers; Correccion del efecto volumetrico en una matriz 2D de camaras de ionizacion

    Energy Technology Data Exchange (ETDEWEB)

    Diaz Fuentes, R.; Cabello Murillo, E.; Rodriguez Rodriguez, C.; Ferrando Sanchez, A.; Clemente Gutierrez, F.; Casas de Julian, M. A. de la; Adaimi Hernandez, P.

    2011-07-01

    There are three main snags related to the measurement of spatial distributions of absorbed dose with two-dimensional array devices of ionisation chambers: spatial under-sampling, volumetric effect and inaccuracy in electric charge to absorbed dose conversion coefficient due to lack of lateral electronic equilibrium. In this work we have experimentally estimated the error in the raw measurement of dose by one of such chambers. We have found that the major error factor is the volumetric effect, which can be corrected through the well-known techniques of convolution/deconvolution. (Author) 14 refs.

  6. Planning strategies in volumetric modulated arc therapy for breast.

    Science.gov (United States)

    Nicolini, Giorgia; Fogliata, Antonella; Clivio, Alessandro; Vanetti, Eugenio; Cozzi, Luca

    2011-07-01

    In breast radiotherapy with intensity modulation, it is a well established practice to extend the dose fluence outside the limit of the body contour to account for small changes in size and position of the target and the rest of the tissues due to respiration or to possible oedema. A simple approach is not applicable with RapidArc volumetric modulated arc therapy not being based on a fixed field fluence delivery. In this study, a viable technical strategy to account for this need is presented. RapidArc (RA) plans for six breast cancer patients (three right and three left cases), were optimized (PRO version III) on the original CT data set (O) and on an alternative CT (E) generated with an artificial expansion (and assignment of soft-tissue equivalent HU) of 10 mm of the body in the breast region and of the PTV contours toward the external direction. Final dose calculations for the two set of plans were performed on the same original CT data set O, normalizing the dose prescription (50 Gy) to the target mean. In this way, two treatment plans on the same CT set O for each patient were obtained: the no action plan (OO) and the alternative plan based on an expanded optimization (EO). Fixing MU, these two plans were then recomputed on the expanded CT data set and on an intermediate one (with expansion = 5 mm), to mimic, possible changes in size due to edema during treatment or residual displacements due to breathing not properly controlled. Aim of the study was to quantify the robustness of this planning strategy on dose distributions when either the OO or the EO strategies were adopted. For all the combinations, a DVH analysis of all involved structures is reported. I. The two optimization approaches gave comparable dose distributions on the original CT data set. II. When plans were evaluated on the expanded CTs (mimicking the presence of edema), the EO approach showed improved target coverage if compared to OO: on CT_10 mm, DV = 98% [%] = 92.5 ± 0

  7. Real-time volumetric image reconstruction and 3D tumor localization based on a single x-ray projection image for lung cancer radiotherapy

    CERN Document Server

    Li, Ruijiang; Lewis, John H; Gu, Xuejun; Folkerts, Michael; Men, Chunhua; Jiang, Steve B

    2010-01-01

    Purpose: To develop an algorithm for real-time volumetric image reconstruction and 3D tumor localization based on a single x-ray projection image for lung cancer radiotherapy. Methods: Given a set of volumetric images of a patient at N breathing phases as the training data, we perform deformable image registration between a reference phase and the other N-1 phases, resulting in N-1 deformation vector fields (DVFs). These DVFs can be represented efficiently by a few eigenvectors and coefficients obtained from principal component analysis (PCA). By varying the PCA coefficients, we can generate new DVFs, which, when applied on the reference image, lead to new volumetric images. We then can reconstruct a volumetric image from a single projection image by optimizing the PCA coefficients such that its computed projection matches the measured one. The 3D location of the tumor can be derived by applying the inverted DVF on its position in the reference image. Our algorithm was implemented on graphics processing units...

  8. Thermal expansion in lead zirconate titanate

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    The volume anomalies with temperature variations in tin-modified lead zirconate titanate ceramics are investigated. Experimental results show that the volume changes are related to the phase transitions induced with temperature. The magnitude and orientation of crystal volume changes are dependent on the particular phase transition. When antiferroelectrics is transformed to ferroelectrics or paraelectrics the volume expands. Oppositely when ferroelectrics is transformed to antiferroelectrics or paraelectrics the volume contracts. In the transition of antiferroelectric orthorhombic structure to tetragonal structure or ferroelectric low-temperature rhombohedral structure to high-tem- perature rhombohedral structure, there are also revealed apparent anomalies in the curves of thermal expansion. Among them, the volume strain caused by the transition between antiferroelectrics and ferroelectrics is the biggest in magnitude, and the linear expansion dL/L0 and the expansion coefficient (dL/L0)/dT can reach 2.810?3 and 7.5 × 10?4 K?1 respectively.

  9. Radial expansion for spinning conformal blocks

    CERN Document Server

    Costa, Miguel; Hansen, Tobias; Penedones, João; Trevisani, Emilio

    2016-01-01

    This paper develops a method to compute any bosonic conformal block as a series expansion in the optimal radial coordinate introduced by Hogervorst and Rychkov. The method reduces to the known result when the external operators are all the same scalar operator, but it allows to compute conformal blocks for external operators with spin. Moreover, we explain how to write closed form recursion relations for the coefficients of the expansions. We study three examples of four point functions in detail: one vector and three scalars; two vectors and two scalars; two spin 2 tensors and two scalars. Finally, for the case of two external vectors, we also provide a more efficient way to generate the series expansion using the analytic structure of the blocks as a function of the scaling dimension of the exchanged operator.

  10. Eigenvalues and expansion of bipartite graphs

    DEFF Research Database (Denmark)

    Høholdt, Tom; Janwa, Heeralal

    2012-01-01

    We prove lower bounds on the largest and second largest eigenvalue of the adjacency matrix of bipartite graphs and give necessary and sufficient conditions for equality. We give several examples of classes that are optimal with respect to the bouns. We prove that BIBD-graphs are characterized by ...... by their eigenvalues. Finally we present a new bound on the expansion coefficient of (c,d)-regular bipartite graphs and compare that with aclassical bound....

  11. Operator product expansion at finite temperature

    OpenAIRE

    Mallik, S.

    1997-01-01

    We extend an earlier, configuration space method to find the Wilson coefficients of operators appearing in the short distance expansion of thermal correlation functions of different quark bilinears. Considering all the different correlation functions, there arise, up to dimension four, two new operators, in addition to the two appearing already in the vacuum correlation functions. They would contribute substantially to the QCD sum rules, when the temperature is not too low.

  12. Low-Thermal-Expansion Filled Polytetrafluoroethylene

    Science.gov (United States)

    Shapiro, Sanford S.

    1989-01-01

    PTFE made thermally compatible with aluminum without changing dielectric constant. Manufactured with fillers and pores to reduce coefficient of thermal expansion by factor of 6 to match aluminum. Material retains 2.1 dielectric constant of pure PTFE. Combines filler and micropore concepts. Particles and voids embedded in PTFE matrix function cooperatively. Particles take up compressive stress imposed by contracting PTFE, and voids take up expanding material. Increases dielectric constant, while voids reduce it.

  13. Characterizing volumetric deformation behavior of naturally occuring bituminous sand materials

    CSIR Research Space (South Africa)

    Anochie-Boateng, Joseph

    2009-05-01

    Full Text Available newly proposed hydrostatic compression test procedure. The test procedure applies field loading conditions of off-road construction and mining equipment to closely simulate the volumetric deformation and stiffness behaviour of oil sand materials. Based...

  14. Hyperspectral image classification based on volumetric texture and dimensionality reduction

    Science.gov (United States)

    Su, Hongjun; Sheng, Yehua; Du, Peijun; Chen, Chen; Liu, Kui

    2015-06-01

    A novel approach using volumetric texture and reduced-spectral features is presented for hyperspectral image classification. Using this approach, the volumetric textural features were extracted by volumetric gray-level co-occurrence matrices (VGLCM). The spectral features were extracted by minimum estimated abundance covariance (MEAC) and linear prediction (LP)-based band selection, and a semi-supervised k-means (SKM) clustering method with deleting the worst cluster (SKMd) bandclustering algorithms. Moreover, four feature combination schemes were designed for hyperspectral image classification by using spectral and textural features. It has been proven that the proposed method using VGLCM outperforms the gray-level co-occurrence matrices (GLCM) method, and the experimental results indicate that the combination of spectral information with volumetric textural features leads to an improved classification performance in hyperspectral imagery.

  15. Designing remote web-based mechanical-volumetric flow meter ...

    African Journals Online (AJOL)

    ... remote web-based mechanical-volumetric flow meter reading systems based on ... damage and also provides the ability to control and manage consumption. ... existing infrastructure of the telecommunications is used in data transmission.

  16. Buchdahl's glass dispersion coefficients calculated from Schott equation constants.

    Science.gov (United States)

    Reardon, P J; Chipman, R A

    1989-08-15

    A method for the rapid evaluation of Buchdahl's dispersion coefficients at an arbitrary base wavelength given the Schott equation constants is presented. Buchdahl's chromatic coordinate transformation is performed on the Schott equation for the refractive index. A Taylor series expansion of the transformed Schott equation is then equated to the square of the Buchdahl dispersion model. Equations for Buchdahl's dispersion coefficients are then obtained for any base wavelength by matching the power of Buchdahl's chromatic coordinate omega out to fourth order.

  17. Negative thermal expansion

    Energy Technology Data Exchange (ETDEWEB)

    Barrera, G D [Departamento de QuImica, Universidad Nacional de la Patagonia SJB, Ciudad Universitaria, 9000 Comodoro Rivadavia (Argentina); Bruno, J A O [Universidad de Buenos Aires, Facultad de Ciencias Exactas y Naturales, Departamento de QuImica Inorganica, AnalItica y QuImica FIsica, Pabellon 2, Ciudad Universitaria, 1428 Buenos Aires (Argentina); Barron, T H K [School of Chemistry, University of Bristol, Cantock' s Close, Bristol BS8 1TS (United Kingdom); Allan, N L [School of Chemistry, University of Bristol, Cantock' s Close, Bristol BS8 1TS (United Kingdom)

    2005-02-02

    There has been substantial renewed interest in negative thermal expansion following the discovery that cubic ZrW{sub 2}O{sub 8} contracts over a temperature range in excess of 1000 K. Substances of many different kinds show negative thermal expansion, especially at low temperatures. In this article we review the underlying thermodynamics, emphasizing the roles of thermal stress and elasticity. We also discuss vibrational and non-vibrational mechanisms operating on the atomic scale that are responsible for negative expansion, both isotropic and anisotropic, in a wide range of materials. (topical review)

  18. Increasing the volumetric efficiency of Diesel engines by intake pipes

    Science.gov (United States)

    List, Hans

    1933-01-01

    Development of a method for calculating the volumetric efficiency of piston engines with intake pipes. Application of this method to the scavenging pumps of two-stroke-cycle engines with crankcase scavenging and to four-stroke-cycle engines. The utility of the method is demonstrated by volumetric-efficiency tests of the two-stroke-cycle engines with crankcase scavenging. Its practical application to the calculation of intake pipes is illustrated by example.

  19. Serial volumetric registration of pulmonary CT studies

    Science.gov (United States)

    Silva, José Silvestre; Silva, Augusto; Sousa Santos, Beatriz

    2008-03-01

    Detailed morphological analysis of pulmonary structures and tissue, provided by modern CT scanners, is of utmost importance as in the case of oncological applications both for diagnosis, treatment, and follow-up. In this case, a patient may go through several tomographic studies throughout a period of time originating volumetric sets of image data that must be appropriately registered in order to track suspicious radiological findings. The structures or regions of interest may change their position or shape in CT exams acquired at different moments, due to postural, physiologic or pathologic changes, so, the exams should be registered before any follow-up information can be extracted. Postural mismatching throughout time is practically impossible to avoid being particularly evident when imaging is performed at the limiting spatial resolution. In this paper, we propose a method for intra-patient registration of pulmonary CT studies, to assist in the management of the oncological pathology. Our method takes advantage of prior segmentation work. In the first step, the pulmonary segmentation is performed where trachea and main bronchi are identified. Then, the registration method proceeds with a longitudinal alignment based on morphological features of the lungs, such as the position of the carina, the pulmonary areas, the centers of mass and the pulmonary trans-axial principal axis. The final step corresponds to the trans-axial registration of the corresponding pulmonary masked regions. This is accomplished by a pairwise sectional registration process driven by an iterative search of the affine transformation parameters leading to optimal similarity metrics. Results with several cases of intra-patient, intra-modality registration, up to 7 time points, show that this method provides accurate registration which is needed for quantitative tracking of lesions and the development of image fusion strategies that may effectively assist the follow-up process.

  20. Volumetric optoacoustic monitoring of endovenous laser treatments

    Science.gov (United States)

    Fehm, Thomas F.; Deán-Ben, Xosé L.; Schaur, Peter; Sroka, Ronald; Razansky, Daniel

    2016-03-01

    Chronic venous insufficiency (CVI) is one of the most common medical conditions with reported prevalence estimates as high as 30% in the adult population. Although conservative management with compression therapy may improve the symptoms associated with CVI, healing often demands invasive procedures. Besides established surgical methods like vein stripping or bypassing, endovenous laser therapy (ELT) emerged as a promising novel treatment option during the last 15 years offering multiple advantages such as less pain and faster recovery. Much of the treatment success hereby depends on monitoring of the treatment progression using clinical imaging modalities such as Doppler ultrasound. The latter however do not provide sufficient contrast, spatial resolution and three-dimensional imaging capacity which is necessary for accurate online lesion assessment during treatment. As a consequence, incidence of recanalization, lack of vessel occlusion and collateral damage remains highly variable among patients. In this study, we examined the capacity of volumetric optoacoustic tomography (VOT) for real-time monitoring of ELT using an ex-vivo ox foot model. ELT was performed on subcutaneous veins while optoacoustic signals were acquired and reconstructed in real-time and at a spatial resolution in the order of 200μm. VOT images showed spatio-temporal maps of the lesion progression, characteristics of the vessel wall, and position of the ablation fiber's tip during the pull back. It was also possible to correlate the images with the temperature elevation measured in the area adjacent to the ablation spot. We conclude that VOT is a promising tool for providing online feedback during endovenous laser therapy.

  1. Treatment planning for volumetric modulated arc therapy

    Energy Technology Data Exchange (ETDEWEB)

    Bedford, James L. [Joint Department of Physics, Institute of Cancer Research and The Royal Marsden NHS Foundation Trust, Downs Road, Sutton, Surrey SM2 5PT (United Kingdom)

    2009-11-15

    Purpose: Volumetric modulated arc therapy (VMAT) is a specific type of intensity-modulated radiation therapy (IMRT) in which the gantry speed, multileaf collimator (MLC) leaf position, and dose rate vary continuously during delivery. A treatment planning system for VMAT is presented. Methods: Arc control points are created uniformly throughout one or more arcs. An iterative least-squares algorithm is used to generate a fluence profile at every control point. The control points are then grouped and all of the control points in a given group are used to approximate the fluence profiles. A direct-aperture optimization is then used to improve the solution, taking into account the allowed range of leaf motion of the MLC. Dose is calculated using a fast convolution algorithm and the motion between control points is approximated by 100 interpolated dose calculation points. The method has been applied to five cases, consisting of lung, rectum, prostate and seminal vesicles, prostate and pelvic lymph nodes, and head and neck. The resulting plans have been compared with segmental (step-and-shoot) IMRT and delivered and verified on an Elekta Synergy to ensure practicality. Results: For the lung, prostate and seminal vesicles, and rectum cases, VMAT provides a plan of similar quality to segmental IMRT but with faster delivery by up to a factor of 4. For the prostate and pelvic nodes and head-and-neck cases, the critical structure doses are reduced with VMAT, both of these cases having a longer delivery time than IMRT. The plans in general verify successfully, although the agreement between planned and measured doses is not very close for the more complex cases, particularly the head-and-neck case. Conclusions: Depending upon the emphasis in the treatment planning, VMAT provides treatment plans which are higher in quality and/or faster to deliver than IMRT. The scheme described has been successfully introduced into clinical use.

  2. Visualization and volumetric structures from MR images of the brain

    Energy Technology Data Exchange (ETDEWEB)

    Parvin, B.; Johnston, W.; Robertson, D.

    1994-03-01

    Pinta is a system for segmentation and visualization of anatomical structures obtained from serial sections reconstructed from magnetic resonance imaging. The system approaches the segmentation problem by assigning each volumetric region to an anatomical structure. This is accomplished by satisfying constraints at the pixel level, slice level, and volumetric level. Each slice is represented by an attributed graph, where nodes correspond to regions and links correspond to the relations between regions. These regions are obtained by grouping pixels based on similarity and proximity. The slice level attributed graphs are then coerced to form a volumetric attributed graph, where volumetric consistency can be verified. The main novelty of our approach is in the use of the volumetric graph to ensure consistency from symbolic representations obtained from individual slices. In this fashion, the system allows errors to be made at the slice level, yet removes them when the volumetric consistency cannot be verified. Once the segmentation is complete, the 3D surfaces of the brain can be constructed and visualized.

  3. Soft bilateral filtering volumetric shadows using cube shadow maps

    Science.gov (United States)

    Ali, Hatam H.; Sunar, Mohd Shahrizal; Kolivand, Hoshang

    2017-01-01

    Volumetric shadows often increase the realism of rendered scenes in computer graphics. Typical volumetric shadows techniques do not provide a smooth transition effect in real-time with conservation on crispness of boundaries. This research presents a new technique for generating high quality volumetric shadows by sampling and interpolation. Contrary to conventional ray marching method, which requires extensive time, this proposed technique adopts downsampling in calculating ray marching. Furthermore, light scattering is computed in High Dynamic Range buffer to generate tone mapping. The bilateral interpolation is used along a view rays to smooth transition of volumetric shadows with respect to preserving-edges. In addition, this technique applied a cube shadow map to create multiple shadows. The contribution of this technique isreducing the number of sample points in evaluating light scattering and then introducing bilateral interpolation to improve volumetric shadows. This contribution is done by removing the inherent deficiencies significantly in shadow maps. This technique allows obtaining soft marvelous volumetric shadows, having a good performance and high quality, which show its potential for interactive applications. PMID:28632740

  4. Prestarlike functions with negative coefficients

    Directory of Open Access Journals (Sweden)

    H. Silverman

    1979-01-01

    Full Text Available The extreme points for prestarlike functions having negative coefficients are determined. Coefficient, distortion and radii of univalence, starlikeness, and convexity theorems are also obtained.

  5. Thermal Expansion "Paradox."

    Science.gov (United States)

    Fakhruddin, Hasan

    1993-01-01

    Describes a paradox in the equation for thermal expansion. If the calculations for heating a rod and subsequently cooling a rod are determined, the new length of the cool rod is shorter than expected. (PR)

  6. Integral transform solution of natural convection in a square cavity with volumetric heat generation

    Directory of Open Access Journals (Sweden)

    C. An

    2013-12-01

    Full Text Available The generalized integral transform technique (GITT is employed to obtain a hybrid numerical-analytical solution of natural convection in a cavity with volumetric heat generation. The hybrid nature of this approach allows for the establishment of benchmark results in the solution of non-linear partial differential equation systems, including the coupled set of heat and fluid flow equations that govern the steady natural convection problem under consideration. Through performing the GITT, the resulting transformed ODE system is then numerically solved by making use of the subroutine DBVPFD from the IMSL Library. Therefore, numerical results under user prescribed accuracy are obtained for different values of Rayleigh numbers, and the convergence behavior of the proposed eigenfunction expansions is illustrated. Critical comparisons against solutions produced by ANSYS CFX 12.0 are then conducted, which demonstrate excellent agreement. Several sets of reference results for natural convection with volumetric heat generation in a bi-dimensional square cavity are also provided for future verification of numerical results obtained by other researchers.

  7. Gorenstein Hilbert Coefficients

    CERN Document Server

    Khoury, Sabine El

    2012-01-01

    We prove upper and lower bounds for all the coefficients in the Hilbert Polynomial of a graded Gorenstein algebra $S=R/I$ with a quasi-pure resolution over $R$. The bounds are in terms of the minimal and the maximal shifts in the resolution of $R$ . These bounds are analogous to the bounds for the multiplicity found in \\cite{S} and are stronger than the bounds for the Cohen Macaulay algebras found in \\cite{HZ}.

  8. Improving plan quality for prostate volumetric-modulated arc therapy.

    Science.gov (United States)

    Wright, Katrina; Ferrari-Anderson, Janet; Barry, Tamara; Bernard, Anne; Brown, Elizabeth; Lehman, Margot; Pryor, David

    2017-08-04

    We critically evaluated the quality and consistency of volumetric-modulated arc therapy (VMAT) prostate planning at a single institution to quantify objective measures for plan quality and establish clear guidelines for plan evaluation and quality assurance. A retrospective analysis was conducted on 34 plans generated on the Pinnacle(3) version 9.4 and 9.8 treatment planning system to deliver 78 Gy in 39 fractions to the prostate only using VMAT. Data were collected on contoured structure volumes, overlaps and expansions, planning target volume (PTV) and organs at risk volumes and relationship, dose volume histogram, plan conformity, plan homogeneity, low-dose wash, and beam parameters. Standard descriptive statistics were used to describe the data. Despite a standardized planning protocol, we found variability was present in all steps of the planning process. Deviations from protocol contours by radiation oncologists and radiation therapists occurred in 12% and 50% of cases, respectively, and the number of optimization parameters ranged from 12 to 27 (median 17). This contributed to conflicts within the optimization process reflected by the mean composite objective value of 0.07 (range 0.01 to 0.44). Methods used to control low-intermediate dose wash were inconsistent. At the PTV rectum interface, the dose-gradient distance from the 74.1 Gy to 40 Gy isodose ranged from 0.6 cm to 2.0 cm (median 1.0 cm). Increasing collimator angle was associated with a decrease in monitor units and a single full 6 MV arc was sufficient for the majority of plans. A significant relationship was found between clinical target volume-rectum distance and rectal tolerances achieved. A linear relationship was determined between the PTV volume and volume of 40 Gy isodose. Objective values and composite objective values were useful in determining plan quality. Anatomic geometry and overlap of structures has a measurable impact on the plan quality achieved for prostate patients

  9. On the use of volumetric strain meters to infer additional characteristics of short-period seismic radiation

    Science.gov (United States)

    Borcherdt, R.D.; Johnston, M.J.S.; Glassmoyer, G.

    1989-01-01

    Volumetric strain meters (Sacks-Evertson design) are installed at 15 sites along the San Andreas fault system, to monitor long-term strain changes for earthquake prediction. Deployment of portable broadband, high-resolution digital recorders (GEOS) at several of the sites extends the detection band for volumetric strain to periods shorter than 5 ?? 10-2 sec and permits the simultaneous observation of seismic radiation fields using conventional short-period pendulum seismometers. Recordings of local and regional earthquakes indicate that dilatometers respond to P energy but not direct shear energy and that straingrams can be used to resolve superimposed reflect P and S waves for inference of wave characteristics not permitted by either sensor alone. Simultaneous measurements of incident P- and S-wave amplitudes are used to introduce a technique for single-station estimates of wave field inhomogeneity, free-surface reflection coefficients and local material P velocity. -from Authors

  10. Engineering three-dimensionally electrodeposited Si-on-Ni inverse opal structure for high volumetric capacity Li-ion microbattery anode.

    Science.gov (United States)

    Liu, Hao; Cho, Hyung-Man; Meng, Ying Shirley; Li, Quan

    2014-06-25

    Aiming at improving the volumetric capacity of nanostructured Li-ion battery anode, an electrodeposited Si-on-Ni inverse opal structure has been proposed in the present work. This type of electrode provides three-dimensional bi-continuous pathways for ion/electron transport and high surface area-to-volume ratios, and thus exhibits lower interfacial resistance, but higher effective Li ions diffusion coefficients, when compared to the Si-on-Ni nanocable array electrode of the same active material mass. As a result, improved volumetric capacities and rate capabilities have been demonstrated in the Si-on-Ni inverse opal anode. We also show that optimization of the volumetric capacities and the rate performance of the inverse opal electrode can be realized by manipulating the pore size of the Ni scaffold and the thickness of the Si deposit.

  11. Closed-Form Expansions for Transition Densities of Convenience Yield Processes

    Directory of Open Access Journals (Sweden)

    Sanae RUJIVAN

    2009-01-01

    Full Text Available In this paper, we derive closed-form expansions for transition densities of convenience yield processes modeled by using extended Cox-Ingersoll-Ross (ECIR processes. The closed-form expansions can be used for all cases of model having appropriate drift and diffusion coefficients. In terms of the efficiency, the closed-form expansions are close to the exact transition densities when the number of terms in the expansions is large and the time step size is small.

  12. Solving the Boltzmann equation to obtain electron transport coefficients and rate coefficients for fluid models

    Energy Technology Data Exchange (ETDEWEB)

    Hagelaar, G J M; Pitchford, L C [Centre de Physique des Plasmas et de leurs Applications de Toulouse, Universite Paul Sabatier, 118 route de Narbonne, 31062 Toulouse Cedex 9 (France)

    2005-11-15

    Fluid models of gas discharges require the input of transport coefficients and rate coefficients that depend on the electron energy distribution function. Such coefficients are usually calculated from collision cross-section data by solving the electron Boltzmann equation (BE). In this paper we present a new user-friendly BE solver developed especially for this purpose, freely available under the name BOLSIG+, which is more general and easier to use than most other BE solvers available. The solver provides steady-state solutions of the BE for electrons in a uniform electric field, using the classical two-term expansion, and is able to account for different growth models, quasi-stationary and oscillating fields, electron-neutral collisions and electron-electron collisions. We show that for the approximations we use, the BE takes the form of a convection-diffusion continuity-equation with a non-local source term in energy space. To solve this equation we use an exponential scheme commonly used for convection-diffusion problems. The calculated electron transport coefficients and rate coefficients are defined so as to ensure maximum consistency with the fluid equations. We discuss how these coefficients are best used in fluid models and illustrate the influence of some essential parameters and approximations.

  13. Utilization of sensitivity coefficients to guide the design of a thermal battery

    Energy Technology Data Exchange (ETDEWEB)

    Blackwell, B.F.; Dowding, K.J.; Cochran, R.J.; Dobranich, D.

    1998-08-01

    Equations are presented to describe the sensitivity of the temperature field in a heat-conducting body to changes in the volumetric heat source and volumetric heat capacity. These sensitivity equations, along with others not presented, are applied to a thermal battery problem to compute the sensitivity of the temperature field to 19 model input parameters. Sensitivity coefficients, along with assumed standard deviation in these parameters, are used to estimate the uncertainty in the temperature prediction. From the 19 parameters investigated, the battery cell heat source and volumetric heat capacity were clearly identified as being the major contributors to the overall uncertainty in the temperature predictions. The operational life of the thermal battery was shown to be very sensitive to uncertainty in these parameters.

  14. The Truth About Ballistic Coefficients

    CERN Document Server

    Courtney, Michael

    2007-01-01

    The ballistic coefficient of a bullet describes how it slows in flight due to air resistance. This article presents experimental determinations of ballistic coefficients showing that the majority of bullets tested have their previously published ballistic coefficients exaggerated from 5-25% by the bullet manufacturers. These exaggerated ballistic coefficients lead to inaccurate predictions of long range bullet drop, retained energy and wind drift.

  15. Associativity of the operator product expansion

    CERN Document Server

    Holland, Jan

    2015-01-01

    We consider a recursive scheme for defining the coefficients in the operator product expansion (OPE) of an arbitrary number of composite operators in the context of perturbative, Euclidean quantum field theory in four dimensions. Our iterative scheme is consistent with previous definitions of OPE coefficients via the flow equation method, or methods based on Feynman diagrams. It allows us to prove that a strong version of the "associativity" condition holds for the OPE to arbitrary orders in perturbation theory. Such a condition was previously proposed in an axiomatic setting in [1] and has interesting conceptual consequences: 1) One can characterise perturbations of quantum field theories abstractly in a sort of "Hochschild-like" cohomology setting, 2) one can prove a "coherence theorem" analogous to that in an ordinary algebra: The OPE coefficients for a product of two composite operators uniquely determine those for $n$ composite operators. We concretely prove our main results for the Euclidean $\\varphi^4_...

  16. Experimental investigation of friction coefficient in tube hydroforming

    Institute of Scientific and Technical Information of China (English)

    Hyae Kyung YI; Hong Sup YIM; Gun Yeop LEE; Sung Mun LEE; Gi Suk CHUNG; Young-Hoon MOON

    2011-01-01

    The friction coefficient between tube and die in guide zone of tube hydroforming was obtained. In hydroforming, the tube is expanded by an internal pressure against the tool wall. By pushing the tube through tool, a friction force at the contact surface between the tube and the tool occurs. In guiding zone, the friction coefficients between tube and die can be estimated from the measured axial feeding forces. In expansion zone, the friction coefficients between tube and die can be evaluated from the measured geometries of expanded tubes and FE analysis.

  17. Non-linear Bayesian update of PCE coefficients

    KAUST Repository

    Litvinenko, Alexander

    2014-01-06

    Given: a physical system modeled by a PDE or ODE with uncertain coefficient q(?), a measurement operator Y (u(q), q), where u(q, ?) uncertain solution. Aim: to identify q(?). The mapping from parameters to observations is usually not invertible, hence this inverse identification problem is generally ill-posed. To identify q(!) we derived non-linear Bayesian update from the variational problem associated with conditional expectation. To reduce cost of the Bayesian update we offer a unctional approximation, e.g. polynomial chaos expansion (PCE). New: We apply Bayesian update to the PCE coefficients of the random coefficient q(?) (not to the probability density function of q).

  18. Lightweight Mechanical Metamaterials with Tunable Negative Thermal Expansion.

    Science.gov (United States)

    Wang, Qiming; Jackson, Julie A; Ge, Qi; Hopkins, Jonathan B; Spadaccini, Christopher M; Fang, Nicholas X

    2016-10-21

    Ice floating on water is a great manifestation of negative thermal expansion (NTE) in nature. The limited examples of natural materials possessing NTE have stimulated research on engineered structures. Previous studies on NTE structures were mostly focused on theoretical design with limited experimental demonstration in two-dimensional planar geometries. In this work, aided with multimaterial projection microstereolithography, we experimentally fabricate lightweight multimaterial lattices that exhibit significant negative thermal expansion in three directions and over a temperature range of 170 degrees. Such NTE is induced by the structural interaction of material components with distinct thermal expansion coefficients. The NTE can be tuned over a large range by varying the thermal expansion coefficient difference between constituent beams and geometrical arrangements. Our experimental results match qualitatively with a simple scaling law and quantitatively with computational models.

  19. Lightweight Mechanical Metamaterials with Tunable Negative Thermal Expansion

    Science.gov (United States)

    Wang, Qiming; Jackson, Julie A.; Ge, Qi; Hopkins, Jonathan B.; Spadaccini, Christopher M.; Fang, Nicholas X.

    2016-10-01

    Ice floating on water is a great manifestation of negative thermal expansion (NTE) in nature. The limited examples of natural materials possessing NTE have stimulated research on engineered structures. Previous studies on NTE structures were mostly focused on theoretical design with limited experimental demonstration in two-dimensional planar geometries. In this work, aided with multimaterial projection microstereolithography, we experimentally fabricate lightweight multimaterial lattices that exhibit significant negative thermal expansion in three directions and over a temperature range of 170 degrees. Such NTE is induced by the structural interaction of material components with distinct thermal expansion coefficients. The NTE can be tuned over a large range by varying the thermal expansion coefficient difference between constituent beams and geometrical arrangements. Our experimental results match qualitatively with a simple scaling law and quantitatively with computational models.

  20. Bilocal expansion of Borel amplitude and hadronic tau decay width

    CERN Document Server

    Cvetic, G; Cvetic, Gorazd; Lee, Taekoon

    2001-01-01

    The singular part of Borel transform of a QCD amplitude near the infrared renormalon can be expanded in terms of higher order Wilson coefficients of the operators associated with the renormalon. In this paper we observe that this expansion gives nontrivial constraints on the Borel amplitude that can be used to improve the accuracy of the ordinary perturbative expansion of the Borel amplitude. In particular, we consider the Borel transform of the Adler function and its expansion around the first infrared renormalon due to the gluon condensate. Using the next-to-leading order Wilson coefficient of the gluon condensate operator, we obtain an exact constraint on the Borel amplitude at the first IR renormalon. We then extrapolate, using judiciously chosen conformal transformations and Pade approximants, the ordinary perturbative expansion of the Borel amplitude in such a way that this constraint is satisfied. This procedure allows us to predict the four-loop Adler function, which gives a result consistent with the...

  1. Structure and thermal expansion of NbC complex carbides

    Energy Technology Data Exchange (ETDEWEB)

    Khatsinskaya, I.M.; Chaporova, I.N.; Cheburaeva, R.F.; Samojlov, A.I.; Logunov, A.V.; Ignatova, I.A.; Dodonova, L.P.

    1983-11-01

    Alloying dependences of the crystal lattice parameters at indoor temperature and coefficient of thermal linear expansion within a 373-1273 K range are determined for complex NbC-base carbides by the method of mathematical experimental design. It is shown that temperature changes in the linear expansion coefficient of certain complex carbides as distinct from NbC have an anomaly (minimum) within 773-973 K caused by occurring reversible phase transformations. An increase in the coefficient of thermal linear expansion and a decrease in hardness of NbC-base tungsten-, molybdenum-, vanadium- and hafnium-alloyed carbides show a weakening of a total chemical bond in the complex carbides during alloying.

  2. Expansion of tabulated scattering matrices in generalized spherical functions

    Science.gov (United States)

    Mishchenko, Michael I.; Geogdzhayev, Igor V.; Yang, Ping

    2016-11-01

    An efficient way to solve the vector radiative transfer equation for plane-parallel turbid media is to Fourier-decompose it in azimuth. This methodology is typically based on the analytical computation of the Fourier components of the phase matrix and is predicated on the knowledge of the coefficients appearing in the expansion of the normalized scattering matrix in generalized spherical functions. Quite often the expansion coefficients have to be determined from tabulated values of the scattering matrix obtained from measurements or calculated by solving the Maxwell equations. In such cases one needs an efficient and accurate computer procedure converting a tabulated scattering matrix into the corresponding set of expansion coefficients. This short communication summarizes the theoretical basis of this procedure and serves as the user guide to a simple public-domain FORTRAN program.

  3. Pressure drop coefficient of laminar Newtonian flow in axisymmetric diffusers

    Energy Technology Data Exchange (ETDEWEB)

    Rosa, S. [Escola Superior de Tecnologia e Gestao, Instituto Politecnico, Campus de Santa Apolonia, 5301-857 Braganca (Portugal)]. E-mail: srosa@ipb.pt; Pinho, F.T. [Centro de Estudos de Fenomenos de Transporte, DEM, Universidade do Minho, Campus de Azurem, 4800-058 Guimaraes (Portugal)]. E-mail: fpinho@fe.up.pt

    2006-04-15

    The laminar flow of Newtonian fluids in axisymmetric diffusers has been numerically investigated to evaluate the pressure-loss coefficient as a function of Reynolds number, diffusion angle and expansion ratio. The numerical simulations were carried out with a finite-volume based code using non-orthogonal collocated grids and second order accurate differencing schemes to discretize all terms of the transport equations. The calculations were carried out for Reynolds numbers between 2 and 200, diffusion angles from 0 deg. to 90 deg. and expansion ratios of 1.5 and 2 and the data are presented in tabular form and as correlations. A simplified 1D theoretical analysis helped explain the various contributions to the loss coefficient and its difference relative to the reversible pressure variation due to differences between the actual and fully developed friction losses, distortions of the velocity profiles and pressure non-uniformity upstream and downstream of the expansion section.

  4. Composite asymptotic expansions

    CERN Document Server

    Fruchard, Augustin

    2013-01-01

    The purpose of these lecture notes is to develop a theory of asymptotic expansions for functions involving two variables, while at the same time using functions involving one variable and functions of the quotient of these two variables. Such composite asymptotic expansions (CAsEs) are particularly well-suited to describing solutions of singularly perturbed ordinary differential equations near turning points. CAsEs imply inner and outer expansions near turning points. Thus our approach is closely related to the method of matched asymptotic expansions. CAsEs offer two unique advantages, however. First, they provide uniform expansions near a turning point and away from it. Second, a Gevrey version of CAsEs is available and detailed in the lecture notes. Three problems are presented in which CAsEs are useful. The first application concerns canard solutions near a multiple turning point. The second application concerns so-called non-smooth or angular canard solutions. Finally an Ackerberg-O’Malley resonance pro...

  5. Improved volumetric imaging in tomosynthesis using combined multiaxial sweeps.

    Science.gov (United States)

    Gersh, Jacob A; Wiant, David B; Best, Ryan C M; Bennett, Marcus C; Munley, Michael T; King, June D; McKee, Mahta M; Baydush, Alan H

    2010-09-03

    This study explores the volumetric reconstruction fidelity attainable using tomosynthesis with a kV imaging system which has a unique ability to rotate isocentrically and with multiple degrees of mechanical freedom. More specifically, we seek to investigate volumetric reconstructions by combining multiple limited-angle rotational image acquisition sweeps. By comparing these reconstructed images with those of a CBCT reconstruction, we can gauge the volumetric fidelity of the reconstructions. In surgical situations, the described tomosynthesis-based system could provide high-quality volumetric imaging without requiring patient motion, even with rotational limitations present. Projections were acquired using the Digital Integrated Brachytherapy Unit, or IBU-D. A phantom was used which contained several spherical objects of varying contrast. Using image projections acquired during isocentric sweeps around the phantom, reconstructions were performed by filtered backprojection. For each image acquisition sweep configuration, a contrasting sphere is analyzed using two metrics and compared to a gold standard CBCT reconstruction. Since the intersection of a reconstructed sphere and an imaging plane is ideally a circle with an eccentricity of zero, the first metric presented compares the effective eccentricity of intersections of reconstructed volumes and imaging planes. As another metric of volumetric reconstruction fidelity, the volume of one of the contrasting spheres was determined using manual contouring. By comparing these manually delineated volumes with a CBCT reconstruction, we can gauge the volumetric fidelity of reconstructions. The configuration which yielded the highest overall volumetric reconstruction fidelity, as determined by effective eccentricities and volumetric contouring, consisted of two orthogonally-offset 60° L-arm sweeps and a single C-arm sweep which shared a pivot point with one the L-arm sweeps. When compared to a similar configuration that

  6. Aspects of volumetric efficiency measurement for reciprocating engines

    Directory of Open Access Journals (Sweden)

    Pešić Radivoje B.

    2013-01-01

    Full Text Available The volumetric efficiency significantly influences engine output. Both design and dimensions of an intake and exhaust system have large impact on volumetric efficiency. Experimental equipment for measuring of airflow through the engine, which is placed in the intake system, may affect the results of measurements and distort the real picture of the impact of individual structural factors. This paper deals with the problems of experimental determination of intake airflow using orifice plates and the influence of orifice plate diameter on the results of the measurements. The problems of airflow measurements through a multi-process Otto/Diesel engine were analyzed. An original method for determining volumetric efficiency was developed based on in-cylinder pressure measurement during motored operation, and appropriate calibration of the experimental procedure was performed. Good correlation between the results of application of the original method for determination of volumetric efficiency and the results of theoretical model used in research of influence of the intake pipe length on volumetric efficiency was determined. [Acknowledgments. The paper is the result of the research within the project TR 35041 financed by the Ministry of Science and Technological Development of the Republic of Serbia

  7. A Technique for Generating Volumetric Cine MRI (VC-MRI)

    Science.gov (United States)

    Harris, Wendy; Ren, Lei; Cai, Jing; Zhang, You; Chang, Zheng; Yin, Fang-Fang

    2016-01-01

    Purpose To develop a technique to generate on-board volumetric-cine MRI (VC-MRI) using patient prior images, motion modeling and on-board 2D-cine MRI. Methods One phase of a 4D-MRI acquired during patient simulation is used as patient prior images. 3 major respiratory deformation patterns of the patient are extracted from 4D-MRI based on principal-component-analysis. The on-board VC-MRI at any instant is considered as a deformation of the prior MRI. The deformation field is represented as a linear combination of the 3 major deformation patterns. The coefficients of the deformation patterns are solved by the data fidelity constraint using the acquired on-board single 2D-cine MRI. The method was evaluated using both XCAT simulation of lung cancer patients and MRI data from four real liver cancer patients. The accuracy of the estimated VC-MRI was quantitatively evaluated using Volume-Percent-Difference(VPD), Center-of-Mass-Shift(COMS), and target tracking errors. Effects of acquisition orientation, region-of-interest(ROI) selection, patient breathing pattern change and noise on the estimation accuracy were also evaluated. Results Image subtraction of ground-truth with estimated on-board VC-MRI shows fewer differences than image subtraction of ground-truth with prior image. Agreement between profiles in the estimated and ground-truth VC-MRI was achieved with less than 6% error for both XCAT and patient data. Among all XCAT scenarios, the VPD between ground-truth and estimated lesion volumes was on average 8.43±1.52% and the COMS was on average 0.93±0.58mm across all time-steps for estimation based on the ROI region in the sagittal cine images. Matching to ROI in the sagittal view achieved better accuracy when there was substantial breathing pattern change. The technique was robust against noise levels up to SNR=20. For patient data, average tracking errors were less than 2 mm in all directions for all patients. Conclusions Preliminary studies demonstrated the

  8. A Technique for Generating Volumetric Cine-Magnetic Resonance Imaging.

    Science.gov (United States)

    Harris, Wendy; Ren, Lei; Cai, Jing; Zhang, You; Chang, Zheng; Yin, Fang-Fang

    2016-06-01

    The purpose of this study was to develop a techique to generate on-board volumetric cine-magnetic resonance imaging (VC-MRI) using patient prior images, motion modeling, and on-board 2-dimensional cine MRI. One phase of a 4-dimensional MRI acquired during patient simulation is used as patient prior images. Three major respiratory deformation patterns of the patient are extracted from 4-dimensional MRI based on principal-component analysis. The on-board VC-MRI at any instant is considered as a deformation of the prior MRI. The deformation field is represented as a linear combination of the 3 major deformation patterns. The coefficients of the deformation patterns are solved by the data fidelity constraint using the acquired on-board single 2-dimensional cine MRI. The method was evaluated using both digital extended-cardiac torso (XCAT) simulation of lung cancer patients and MRI data from 4 real liver cancer patients. The accuracy of the estimated VC-MRI was quantitatively evaluated using volume-percent-difference (VPD), center-of-mass-shift (COMS), and target tracking errors. Effects of acquisition orientation, region-of-interest (ROI) selection, patient breathing pattern change, and noise on the estimation accuracy were also evaluated. Image subtraction of ground-truth with estimated on-board VC-MRI shows fewer differences than image subtraction of ground-truth with prior image. Agreement between normalized profiles in the estimated and ground-truth VC-MRI was achieved with less than 6% error for both XCAT and patient data. Among all XCAT scenarios, the VPD between ground-truth and estimated lesion volumes was, on average, 8.43 ± 1.52% and the COMS was, on average, 0.93 ± 0.58 mm across all time steps for estimation based on the ROI region in the sagittal cine images. Matching to ROI in the sagittal view achieved better accuracy when there was substantial breathing pattern change. The technique was robust against noise levels up to SNR = 20. For

  9. Novel Foraminal Expansion Technique

    Science.gov (United States)

    Senturk, Salim; Ciplak, Mert; Oktenoglu, Tunc; Sasani, Mehdi; Egemen, Emrah; Yaman, Onur; Suzer, Tuncer

    2016-01-01

    The technique we describe was developed for cervical foraminal stenosis for cases in which a keyhole foraminotomy would not be effective. Many cervical stenosis cases are so severe that keyhole foraminotomy is not successful. However, the technique outlined in this study provides adequate enlargement of an entire cervical foraminal diameter. This study reports on a novel foraminal expansion technique. Linear drilling was performed in the middle of the facet joint. A small bone graft was placed between the divided lateral masses after distraction. A lateral mass stabilization was performed with screws and rods following the expansion procedure. A cervical foramen was linearly drilled medially to laterally, then expanded with small bone grafts, and a lateral mass instrumentation was added with surgery. The patient was well after the surgery. The novel foraminal expansion is an effective surgical method for severe foraminal stenosis. PMID:27559460

  10. High-throughput volumetric reconstruction for 3D wheat plant architecture studies

    Directory of Open Access Journals (Sweden)

    Wei Fang

    2016-09-01

    Full Text Available For many tiller crops, the plant architecture (PA, including the plant fresh weight, plant height, number of tillers, tiller angle and stem diameter, significantly affects the grain yield. In this study, we propose a method based on volumetric reconstruction for high-throughput three-dimensional (3D wheat PA studies. The proposed methodology involves plant volumetric reconstruction from multiple images, plant model processing and phenotypic parameter estimation and analysis. This study was performed on 80 Triticum aestivum plants, and the results were analyzed. Comparing the automated measurements with manual measurements, the mean absolute percentage error (MAPE in the plant height and the plant fresh weight was 2.71% (1.08cm with an average plant height of 40.07cm and 10.06% (1.41g with an average plant fresh weight of 14.06g, respectively. The root mean square error (RMSE was 1.37cm and 1.79g for the plant height and plant fresh weight, respectively. The correlation coefficients were 0.95 and 0.96 for the plant height and plant fresh weight, respectively. Additionally, the proposed methodology, including plant reconstruction, model processing and trait extraction, required only approximately 20s on average per plant using parallel computing on a graphics processing unit (GPU, demonstrating that the methodology would be valuable for a high-throughput phenotyping platform.

  11. Proposal for a material with negative thermal expansion

    Science.gov (United States)

    Abdullah, Mikrajuddin

    2016-09-01

    I propose a model of a material that exhibits negative thermal expansion (NTE) properties and criteria for the occurrence of linear and volumetric NTE. I derived the criteria for an arbitrary force between rigid units in the material. These criteria are also discussed specifically for the Lennard-Jones (6-12) potential and in more detail for metal-organic framework (MOF) materials comprising rigid units connected by organic linkers. Qualitatively, the model predictions can explain some observed results. Surprisingly, the model can produce equations for the transition temperature from NTE to positive thermal expansion (PTE), Tc ≈ T0 - 50 K, which is exactly the same as the temperature at which the glass transition begins to occur in most polymers, i.e., Tc ≈ Tg - 50 K.

  12. Steppe expansion in Patagonia?

    Science.gov (United States)

    Veblen, Thomas T.; Markgraf, Vera

    1988-11-01

    Westward expansion of the Patagonian steppe and retrocession of Andean forests due to increasing aridity over the past one or two millennia has been a persistent theme in the ecological and paleoecological literature for at least half a century. New evidence from pollen profiles, tree-ring analysis, vegetation structure, and photographic and documentary historical sources does not show the expansion of the steppe. Instead, over the past century trees have invaded the steppe as a consequence mainly of human-induced changes in the fire regime, and trees have regenerated in forest areas that were heavily burnt at the onset of European colonization.

  13. Uniform gradient expansions

    Directory of Open Access Journals (Sweden)

    Massimo Giovannini

    2015-06-01

    Full Text Available Cosmological singularities are often discussed by means of a gradient expansion that can also describe, during a quasi-de Sitter phase, the progressive suppression of curvature inhomogeneities. While the inflationary event horizon is being formed the two mentioned regimes coexist and a uniform expansion can be conceived and applied to the evolution of spatial gradients across the protoinflationary boundary. It is argued that conventional arguments addressing the preinflationary initial conditions are necessary but generally not sufficient to guarantee a homogeneous onset of the conventional inflationary stage.

  14. Uniform gradient expansions

    Energy Technology Data Exchange (ETDEWEB)

    Giovannini, Massimo, E-mail: massimo.giovannini@cern.ch [Department of Physics, Theory Division, CERN, 1211 Geneva 23 (Switzerland); INFN, Section of Milan-Bicocca, 20126 Milan (Italy)

    2015-06-30

    Cosmological singularities are often discussed by means of a gradient expansion that can also describe, during a quasi-de Sitter phase, the progressive suppression of curvature inhomogeneities. While the inflationary event horizon is being formed the two mentioned regimes coexist and a uniform expansion can be conceived and applied to the evolution of spatial gradients across the protoinflationary boundary. It is argued that conventional arguments addressing the preinflationary initial conditions are necessary but generally not sufficient to guarantee a homogeneous onset of the conventional inflationary stage.

  15. Dynamic thermal expansivity of liquids near the glass transition

    DEFF Research Database (Denmark)

    Niss, Kristine; Gundermann, Ditte; Christensen, Tage Emil;

    2012-01-01

    Based on previous works on polymers by Bauer et al. [ Phys. Rev. E 61 1755 (2000)], this paper describes a capacitative method for measuring the dynamical expansion coefficient of a viscous liquid. Data are presented for the glass-forming liquid tetramethyl tetraphenyl trisiloxane (DC704) in the ......Based on previous works on polymers by Bauer et al. [ Phys. Rev. E 61 1755 (2000)], this paper describes a capacitative method for measuring the dynamical expansion coefficient of a viscous liquid. Data are presented for the glass-forming liquid tetramethyl tetraphenyl trisiloxane (DC704...

  16. Energetic and Exergetic Analysis of an Ejector-Expansion Refrigeration Cycle Using the Working Fluid R32

    Directory of Open Access Journals (Sweden)

    Zhenying Zhang

    2015-07-01

    Full Text Available The performance characteristics of an ejector-expansion refrigeration cycle (EEC using R32 have been investigated in comparison with that using R134a. The coefficient of performance (COP, the exergy destruction, the exergy efficiency and the suction nozzle pressure drop (SNPD are discussed. The results show that the application of an ejector instead of a throttle valve in R32 cycle decreases the cycle’s total exergy destruction by 8.84%–15.84% in comparison with the basic cycle (BC. The R32 EEC provides 5.22%–13.77% COP improvement and 5.13%–13.83% exergy efficiency improvement respectively over the BC for the given ranges of evaporating and condensing temperatures. There exists an optimum suction nozzle pressure drop (SNPD which gives a maximum system COP and volumetric cooling capacity (VCC under a specified condition. The value of the optimum SNPD mainly depends on the efficiencies of the ejector components, but is virtually independent of evaporating temperature and condensing temperature. In addition, the improvement of the component efficiency, especially the efficiencies of diffusion nozzle and the motive nozzle, can enhance the EEC performance.

  17. A high volume, high throughput volumetric sorption analyzer

    Science.gov (United States)

    Soo, Y. C.; Beckner, M.; Romanos, J.; Wexler, C.; Pfeifer, P.; Buckley, P.; Clement, J.

    2011-03-01

    In this talk we will present an overview of our new Hydrogen Test Fixture (HTF) constructed by the Midwest Research Institute for The Alliance for Collaborative Research in Alternative Fuel Technology to test activated carbon monoliths for hydrogen gas storage. The HTF is an automated, computer-controlled volumetric instrument for rapid screening and manipulation of monoliths under an inert atmosphere (to exclude degradation of carbon from exposure to oxygen). The HTF allows us to measure large quantity (up to 500 g) of sample in a 0.5 l test tank, making our results less sensitive to sample inhomogeneity. The HTF can measure isotherms at pressures ranging from 1 to 300 bar at room temperature. For comparison, other volumetric instruments such as Hiden Isochema's HTP-1 Volumetric Analyser can only measure carbon samples up to 150 mg at pressures up to 200 bar. Work supported by the US DOD Contract # N00164-08-C-GS37.

  18. Volumetric (3D) compressive sensing spectral domain optical coherence tomography.

    Science.gov (United States)

    Xu, Daguang; Huang, Yong; Kang, Jin U

    2014-11-01

    In this work, we proposed a novel three-dimensional compressive sensing (CS) approach for spectral domain optical coherence tomography (SD OCT) volumetric image acquisition and reconstruction. Instead of taking a spectral volume whose size is the same as that of the volumetric image, our method uses a sub set of the original spectral volume that is under-sampled in all three dimensions, which reduces the amount of spectral measurements to less than 20% of that required by the Shan-non/Nyquist theory. The 3D image is recovered from the under-sampled spectral data dimension-by-dimension using the proposed three-step CS reconstruction strategy. Experimental results show that our method can significantly reduce the sampling rate required for a volumetric SD OCT image while preserving the image quality.

  19. Negative thermal expansion induced by intermetallic charge transfer.

    Science.gov (United States)

    Azuma, Masaki; Oka, Kengo; Nabetani, Koichiro

    2015-06-01

    Suppression of thermal expansion is of great importance for industry. Negative thermal expansion (NTE) materials which shrink on heating and expand on cooling are therefore attracting keen attention. Here we provide a brief overview of NTE induced by intermetallic charge transfer in A-site ordered double perovskites SaCu3Fe4O12 and LaCu3Fe4-x Mn x O12, as well as in Bi or Ni substituted BiNiO3. The last compound shows a colossal dilatometric linear thermal expansion coefficient exceeding -70 × 10(-6) K(-1) near room temperature, in the temperature range which can be controlled by substitution.

  20. Uniform Asymptotic Expansion for the Incomplete Beta Function

    Science.gov (United States)

    Nemes, Gergő; Olde Daalhuis, Adri B.

    2016-10-01

    In [Temme N.M., Special functions. An introduction to the classical functions of mathematical physics, A Wiley-Interscience Publication, John Wiley & Sons, Inc., New York, 1996, Section 11.3.3.1] a uniform asymptotic expansion for the incomplete beta function was derived. It was not obvious from those results that the expansion is actually an asymptotic expansion. We derive a remainder estimate that clearly shows that the result indeed has an asymptotic property, and we also give a recurrence relation for the coefficients.

  1. Frequency dependent thermal expansion in binary viscoelasticcomposites

    Energy Technology Data Exchange (ETDEWEB)

    Berryman, James G.

    2007-12-01

    The effective thermal expansion coefficient beta* of abinary viscoelastic composite is shown to be frequency dependent even ifthe thermal expansion coefficients beta A and beta B of both constituentsare themselves frequency independent. Exact calculations for binaryviscoelastic systems show that beta* is related to constituent valuesbeta A, beta B, volume fractions, and bulk moduli KA, KB, as well as tothe overall bulk modulus K* of the composite system. Then, beta* isdetermined for isotropic systems by first bounding (or measuring) K* andtherefore beta*. For anisotropic systems with hexagonal symmetry, theprincipal values of the thermal expansion beta*perp and beta*para can bedetermined exactly when the constituents form a layered system. In allthe examples studied, it is shown explicitly that the eigenvectors of thethermoviscoelastic system possess non-negative dissipation -- despite thecomplicated analytical behavior of the frequency dependent thermalexpansivities themselves. Methods presented have a variety ofapplications from fluid-fluid mixtures to fluid-solid suspensions, andfrom fluid-saturated porous media to viscoelastic solid-solidcomposites.

  2. Multiple sparse volumetric priors for distributed EEG source reconstruction.

    Science.gov (United States)

    Strobbe, Gregor; van Mierlo, Pieter; De Vos, Maarten; Mijović, Bogdan; Hallez, Hans; Van Huffel, Sabine; López, José David; Vandenberghe, Stefaan

    2014-10-15

    We revisit the multiple sparse priors (MSP) algorithm implemented in the statistical parametric mapping software (SPM) for distributed EEG source reconstruction (Friston et al., 2008). In the present implementation, multiple cortical patches are introduced as source priors based on a dipole source space restricted to a cortical surface mesh. In this note, we present a technique to construct volumetric cortical regions to introduce as source priors by restricting the dipole source space to a segmented gray matter layer and using a region growing approach. This extension allows to reconstruct brain structures besides the cortical surface and facilitates the use of more realistic volumetric head models including more layers, such as cerebrospinal fluid (CSF), compared to the standard 3-layered scalp-skull-brain head models. We illustrated the technique with ERP data and anatomical MR images in 12 subjects. Based on the segmented gray matter for each of the subjects, cortical regions were created and introduced as source priors for MSP-inversion assuming two types of head models. The standard 3-layered scalp-skull-brain head models and extended 4-layered head models including CSF. We compared these models with the current implementation by assessing the free energy corresponding with each of the reconstructions using Bayesian model selection for group studies. Strong evidence was found in favor of the volumetric MSP approach compared to the MSP approach based on cortical patches for both types of head models. Overall, the strongest evidence was found in favor of the volumetric MSP reconstructions based on the extended head models including CSF. These results were verified by comparing the reconstructed activity. The use of volumetric cortical regions as source priors is a useful complement to the present implementation as it allows to introduce more complex head models and volumetric source priors in future studies.

  3. Thermal expansion behavior of a β-LiA1SiO4/Cu composite

    Institute of Scientific and Technical Information of China (English)

    WANG Lidong; XUE Zongwei; LIU Zhe; FEI Weidong

    2009-01-01

    A copper matrix composite reinforced by β-LiAlSiO4 with negative thermal expansion coefficient was fabricated using vacuum hot-pressed sintering technique. The thermal expansion behavior of the composite was investigated, and the average residual stress in the matrix was analyzed by a simple model. The results indicate that the residual stress in the matrix affects the thermal expansion properties. After heat treatment, the coefficient of thermal expansion (CTE) of the composite decreases greatly. The CTE of the composite after thermal cycling between 50-350℃ is the lowest.

  4. Expansion of Pannes

    Science.gov (United States)

    For the Long Island, New Jersey, and southern New England region, one facet of marsh drowning as a result of accelerated sea level rise is the expansion of salt marsh ponds and pannes. Over the past century, marsh ponds and pannes have formed and expanded in areas of poor drainag...

  5. Sieve in expansion

    CERN Document Server

    Kowalski, Emmanuel

    2010-01-01

    This is a survey report for the Bourbaki Seminar (Exp. no. 1028, November 2010) concerning sieve and expanders, in particular the recent works of Bourgain, Gamburd and Sarnak introducing "sieve in orbits", and the related developments concerning expansion properties of Cayley graphs of finite linear groups.

  6. AUTO-EXPANSIVE FLOW

    Science.gov (United States)

    Physics suggests that the interplay of momentum, continuity, and geometry in outward radial flow must produce density and concomitant pressure reductions. In other words, this flow is intrinsically auto-expansive. It has been proposed that this process is the key to understanding...

  7. Volumetric measurements of a spatially growing dust acoustic wave

    Science.gov (United States)

    Williams, Jeremiah D.

    2012-11-01

    In this study, tomographic particle image velocimetry (tomo-PIV) techniques are used to make volumetric measurements of the dust acoustic wave (DAW) in a weakly coupled dusty plasma system in an argon, dc glow discharge plasma. These tomo-PIV measurements provide the first instantaneous volumetric measurement of a naturally occurring propagating DAW. These measurements reveal over the measured volume that the measured wave mode propagates in all three spatial dimensional and exhibits the same spatial growth rate and wavelength in each spatial direction.

  8. Volumetric measurements of a spatially growing dust acoustic wave

    Energy Technology Data Exchange (ETDEWEB)

    Williams, Jeremiah D. [Physics Department, Wittenberg University, Springfield, Ohio 45504 (United States)

    2012-11-15

    In this study, tomographic particle image velocimetry (tomo-PIV) techniques are used to make volumetric measurements of the dust acoustic wave (DAW) in a weakly coupled dusty plasma system in an argon, dc glow discharge plasma. These tomo-PIV measurements provide the first instantaneous volumetric measurement of a naturally occurring propagating DAW. These measurements reveal over the measured volume that the measured wave mode propagates in all three spatial dimensional and exhibits the same spatial growth rate and wavelength in each spatial direction.

  9. Volumetric Pricing of Agricultural Water Supplies: A Case Study

    Science.gov (United States)

    Griffin, Ronald C.; Perry, Gregory M.

    1985-07-01

    Models of water consumption by rice producers are conceptualized and then estimated using cross-sectional time series data obtained from 16 Texas canal operators for the years 1977-1982. Two alternative econometric models demonstrate that both volumetric and flat rate water charges are strongly and inversely related to agricultural water consumption. Nonprice conservation incentives accompanying flat rates are hypothesized to explain the negative correlation of flat rate charges and water consumption. Application of these results suggests that water supply organizations in the sample population converting to volumetric pricing will generally reduce water consumption.

  10. EXPLICIT SOLUTIONS TO THE COUPLED KdV EQUATIONS WITH VARIABLE COEFFICIENTS

    Institute of Scientific and Technical Information of China (English)

    徐桂琼; 李志斌

    2005-01-01

    By means of sn-function expansion method and cn-function expansion method,several kinds of explicit solutions to the coupled KdV equations with variable coefficients are obtained, which include three sets of periodic wave-like solutions. These solutions degenerate to solitary wave-like solutions at a certain limit. Some new solutions are presented.

  11. Non-invasive volumetric assessment of aortic atheroma: a core laboratory validation using computed tomography angiography.

    Science.gov (United States)

    Hammadah, Muhammad; Qintar, Mohammed; Nissen, Steven E; John, Julie St; Alkharabsheh, Saqer; Mobolaji-Lawal, Motunrayo; Philip, Femi; Uno, Kiyoko; Kataoka, Yu; Babb, Brett; Poliszczuk, Roman; Kapadia, Samir R; Tuzcu, E Murat; Schoenhagen, Paul; Nicholls, Stephen J; Puri, Rishi

    2016-01-01

    Aortic atherosclerosis has been linked with worse peri- and post-procedural outcomes following a range of aortic procedures. Yet, there are currently no standardized methods for non-invasive volumetric pan-aortic plaque assessment. We propose a novel means of more accurately assessing plaque volume across whole aortic segments using computed tomography angiography (CTA) imaging. Sixty patients who underwent CTA prior to trans-catheter aortic valve implantation were included in this analysis. Specialized software analysis (3mensio Vascular™, Pie Medical, Maastricht, Netherlands) was used to reconstruct images using a centerline approach, thus creating true cross-sectional aortic images, akin to those images produced with intravascular ultrasonography. Following aortic segmentation (from the aortic valve to the renal artery origin), atheroma areas were measured across multiple contiguous evenly spaced (10 mm) cross-sections. Percent atheroma volume (PAV), total atheroma volume (TAV) and calcium score were calculated. In our populations (age 79.9 ± 8.5 years, male 52 %, diabetes 27 %, CAD 84 %, PVD 20 %), mean ± SD number of cross sections measured for each patient was 35.1 ± 3.5 sections. Mean aortic PAV and TAV were 33.2 ± 2.51 % and 83,509 ± 17,078 mm(3), respectively. Median (IQR) calcium score was 1.5 (0.7-2.5). Mean (SD) inter-observer coefficient of variation and agreement for plaque area among 4 different analysts was 14.1 (5.4), and the mean (95 % CI) Lin's concordance correlation coefficient was 0.79 (0.62-0.89), effectively simulating a Core Laboratory scenario. We provide an initial validation of cross-sectional volumetric aortic atheroma assessment using CTA. This proposed methodology highlights the potential for utilizing non-invasive aortic plaque imaging for risk prediction across a range of clinical scenarios.

  12. Converting Sabine absorption coefficients to random incidence absorption coefficients

    DEFF Research Database (Denmark)

    Jeong, Cheol-Ho

    2013-01-01

    Absorption coefficients measured by the chamber method are referred to as Sabine absorption coefficients, which sometimes exceed unity due to the finite size of a sample and non-uniform intensity in the reverberation chambers under test. In this study, conversion methods from Sabine absorption...... coefficients to random incidence absorption coefficients are proposed. The overestimations of the Sabine absorption coefficient are investigated theoretically based on Miki's model for porous absorbers backed by a rigid wall or an air cavity, resulting in conversion factors. Additionally, three optimizations...

  13. An initial study on the estimation of time-varying volumetric treatment images and 3D tumor localization from single MV cine EPID images.

    Science.gov (United States)

    Mishra, Pankaj; Li, Ruijiang; Mak, Raymond H; Rottmann, Joerg; Bryant, Jonathan H; Williams, Christopher L; Berbeco, Ross I; Lewis, John H

    2014-08-01

    In this work the authors develop and investigate the feasibility of a method to estimate time-varying volumetric images from individual MV cine electronic portal image device (EPID) images. The authors adopt a two-step approach to time-varying volumetric image estimation from a single cine EPID image. In the first step, a patient-specific motion model is constructed from 4DCT. In the second step, parameters in the motion model are tuned according to the information in the EPID image. The patient-specific motion model is based on a compact representation of lung motion represented in displacement vector fields (DVFs). DVFs are calculated through deformable image registration (DIR) of a reference 4DCT phase image (typically peak-exhale) to a set of 4DCT images corresponding to different phases of a breathing cycle. The salient characteristics in the DVFs are captured in a compact representation through principal component analysis (PCA). PCA decouples the spatial and temporal components of the DVFs. Spatial information is represented in eigenvectors and the temporal information is represented by eigen-coefficients. To generate a new volumetric image, the eigen-coefficients are updated via cost function optimization based on digitally reconstructed radiographs and projection images. The updated eigen-coefficients are then multiplied with the eigenvectors to obtain updated DVFs that, in turn, give the volumetric image corresponding to the cine EPID image. The algorithm was tested on (1) Eight digital eXtended CArdiac-Torso phantom datasets based on different irregular patient breathing patterns and (2) patient cine EPID images acquired during SBRT treatments. The root-mean-squared tumor localization error is (0.73 ± 0.63 mm) for the XCAT data and (0.90 ± 0.65 mm) for the patient data. The authors introduced a novel method of estimating volumetric time-varying images from single cine EPID images and a PCA-based lung motion model. This is the first method to estimate

  14. An initial study on the estimation of time-varying volumetric treatment images and 3D tumor localization from single MV cine EPID images

    Energy Technology Data Exchange (ETDEWEB)

    Mishra, Pankaj, E-mail: pankaj.mishra@varian.com; Mak, Raymond H.; Rottmann, Joerg; Bryant, Jonathan H.; Williams, Christopher L.; Berbeco, Ross I.; Lewis, John H. [Brigham and Women' s Hospital, Dana-Farber Cancer Institute and Harvard Medical School, Boston, Massachusetts 02115 (United States); Li, Ruijiang [Department of Radiation Oncology, Stanford University School of Medicine, Stanford, California 94305 (United States)

    2014-08-15

    Purpose: In this work the authors develop and investigate the feasibility of a method to estimate time-varying volumetric images from individual MV cine electronic portal image device (EPID) images. Methods: The authors adopt a two-step approach to time-varying volumetric image estimation from a single cine EPID image. In the first step, a patient-specific motion model is constructed from 4DCT. In the second step, parameters in the motion model are tuned according to the information in the EPID image. The patient-specific motion model is based on a compact representation of lung motion represented in displacement vector fields (DVFs). DVFs are calculated through deformable image registration (DIR) of a reference 4DCT phase image (typically peak-exhale) to a set of 4DCT images corresponding to different phases of a breathing cycle. The salient characteristics in the DVFs are captured in a compact representation through principal component analysis (PCA). PCA decouples the spatial and temporal components of the DVFs. Spatial information is represented in eigenvectors and the temporal information is represented by eigen-coefficients. To generate a new volumetric image, the eigen-coefficients are updated via cost function optimization based on digitally reconstructed radiographs and projection images. The updated eigen-coefficients are then multiplied with the eigenvectors to obtain updated DVFs that, in turn, give the volumetric image corresponding to the cine EPID image. Results: The algorithm was tested on (1) Eight digital eXtended CArdiac-Torso phantom datasets based on different irregular patient breathing patterns and (2) patient cine EPID images acquired during SBRT treatments. The root-mean-squared tumor localization error is (0.73 ± 0.63 mm) for the XCAT data and (0.90 ± 0.65 mm) for the patient data. Conclusions: The authors introduced a novel method of estimating volumetric time-varying images from single cine EPID images and a PCA-based lung motion model

  15. An Experimental study of the initial volumetric strain rate effect on the creep behaviour of reconstituted clays

    Science.gov (United States)

    Bagheri, M.; Rezania, M.; Nezhad, M. M.

    2015-09-01

    Clayey soils tend to undergo continuous compression with time, even after excess pore pressures have substantially dissipated. The effect of time on deformation and mechanical response of these soft soils has been the subject of numerous studies. Based on these studies, the observed time-dependent behaviour of clays is mainly related to the evolution of soil volume and strength characteristics with time, which are classified as creep and/or relaxation properties of the soil. Apart from many empirical relationships that have been proposed in the literature to capture the rheological behaviour of clays, a number of viscid constitutive relationships have also been developed which have more attractive theoretical attributes. A particular feature of these viscid models is that their creep parameters often have clear physical meaning (e.g. coefficient of secondary compression, Cα). Sometimes with these models, a parameter referred to as initial/reference volumetric strain rate, has also been alluded as a model parameter. However, unlike Cα, the determination of and its variations with stress level is not properly documented in the literature. In an attempt to better understand , this paper presents an experimental investigation of the reference volumetric strain rate in reconstituted clay specimens. A long-term triaxial creep test, at different shear stress levels and different strain rates, was performed on clay specimen whereby the volumetric strain rate was measured. The obtained results indicated the stress-level dependency and non-linear variation of with time.

  16. Principles of Thermal Expansion in Feldspars

    Science.gov (United States)

    Hovis, Guy; Medford, Aaron; Conlon, Maricate; Tether, Allison; Romanoski, Anthony

    2010-05-01

    Following the recent thermal expansion work of Hovis et al. (1) on AlSi3 feldspars, we have investigated the thermal expansion of plagioclase, Ba-K, and Ca-K feldspar crystalline solutions. X-ray powder diffraction data were collected between room temperature and 925 °C on six natural plagioclase specimens ranging in composition from anorthite to oligoclase, the K-exchanged equivalents of these plagioclase specimens, and five synthetic Ba-K feldspars with compositions ranging from 25 to 99 mol % BaAl2Si2O8. The resulting thermal expansion coefficients (α) for volume have been combined with earlier results for end-member Na- and K-feldspars (2,3). Unlike AlSi3 feldspars, Al2Si2 feldspars, including anorthite and celsian from the present study plus Sr- and Pb-feldspar from other workers (4,5), show essentially constant and very limited thermal expansion, regardless of divalent cation size. In the context of structures where the Lowenstein rule (6) requires Al and Si to alternate among tetrahedra, the proximity of bridging Al-O-Si oxygen ions to divalent neighbors (ranging from 0 to 2) produces short Ca-O (or Ba-O) bonds (7,8) that apparently are the result of local charge-balance requirements (9). Gibbs et al. (10) suggest that short bonds such as these have a partially covalent character. This in turn stiffens the structure. Thus, for feldspar series with coupled substitution the change away from a purely divalent M-site occupant gives the substituting (less strongly bonded) monovalent cations increasingly greater influence on thermal expansion. Overall, then, thermal expansion in the feldspar system is well represented on a plot of α against room-temperature volume, where one sees a quadrilateral bounded by data for (A) AlSi3 feldspars whose expansion behavior is controlled largely by the size of the monovalent alkali-site occupant, (B) Al2Si2 feldspars whose expansion is uniformly limited by partially-covalent bonds between divalent M-site occupants and

  17. Negative thermal expansion in framework compounds

    Indian Academy of Sciences (India)

    R Mittal

    2008-10-01

    We have studied negative thermal expansion (NTE) compounds with chemi- cal compositions of NX2O8 and NX2O7 (N=Zr, Hf and X=W, Mo, V) and M2O (M=Cu, Ag) using the techniques of inelastic neutron scattering and lattice dynamics. There is a large variation in the negative thermal expansion coefficients of these compounds. The inelastic neutron scattering experiments have been carried out using polycrystalline and single crystal samples at ambient pressure as well as at high pressures. Experimental data are useful to confirm the predictions made from our lattice dynamical calculations as well as to check the quality of the interatomic potentials developed by us. We have been able to successfully model the NTE behaviour of these compounds. Our studies show that unusual phonon softening of low energy modes is able to account for NTE in these compounds.

  18. Towards finite density QCD with Taylor expansions

    CERN Document Server

    Karsch, Frithjof; Wagner, Mathias; Wambach, Jochen

    2010-01-01

    Convergence properties of Taylor expansions of observables, which are also used in lattice QCD calculations at non-zero chemical potential, are analyzed in an effective N_f = 2+1 flavor Polyakov-quark-meson model. A recently developed algorithmic technique allows the calculation of higher-order Taylor expansion coefficients in functional approaches. This novel technique is for the first time applied to an effective N_f = 2+1 flavor Polyakov-quark-meson model and the findings are compared with the full model solution at finite densities. The results are used to discuss prospects for locating the QCD phase boundary and a possible critical endpoint in the phase diagram.

  19. Space-Time Transfinite Interpolation of Volumetric Material Properties.

    Science.gov (United States)

    Sanchez, Mathieu; Fryazinov, Oleg; Adzhiev, Valery; Comninos, Peter; Pasko, Alexander

    2015-02-01

    The paper presents a novel technique based on extension of a general mathematical method of transfinite interpolation to solve an actual problem in the context of a heterogeneous volume modelling area. It deals with time-dependent changes to the volumetric material properties (material density, colour, and others) as a transformation of the volumetric material distributions in space-time accompanying geometric shape transformations such as metamorphosis. The main idea is to represent the geometry of both objects by scalar fields with distance properties, to establish in a higher-dimensional space a time gap during which the geometric transformation takes place, and to use these scalar fields to apply the new space-time transfinite interpolation to volumetric material attributes within this time gap. The proposed solution is analytical in its nature, does not require heavy numerical computations and can be used in real-time applications. Applications of this technique also include texturing and displacement mapping of time-variant surfaces, and parametric design of volumetric microstructures.

  20. In Vivo Real Time Volumetric Synthetic Aperture Ultrasound Imaging

    DEFF Research Database (Denmark)

    Bouzari, Hamed; Rasmussen, Morten Fischer; Brandt, Andreas Hjelm;

    2015-01-01

    Synthetic aperture (SA) imaging can be used to achieve real-time volumetric ultrasound imaging using 2-D array transducers. The sensitivity of SA imaging is improved by maximizing the acoustic output, but one must consider the limitations of an ultrasound system, both technical and biological...

  1. Automatic segmentation of pulmonary segments from volumetric chest CT scans.

    NARCIS (Netherlands)

    Rikxoort, E.M. van; Hoop, B. de; Vorst, S. van de; Prokop, M.; Ginneken, B. van

    2009-01-01

    Automated extraction of pulmonary anatomy provides a foundation for computerized analysis of computed tomography (CT) scans of the chest. A completely automatic method is presented to segment the lungs, lobes and pulmonary segments from volumetric CT chest scans. The method starts with lung segmenta

  2. Volumetric T-spline Construction Using Boolean Operations

    Science.gov (United States)

    2013-07-01

    15213, USA 2 Institute for Computational Engineering and Sciences, The University of Texas at Austin, Austin, TX 78712, USA 3 Department of Civil and...and S. Yau. Volumetric harmonic map. Communications in Information and Systems, 3(3):191–202, 2003. 12. C.A.R. Guerra . Simultaneous untangling and

  3. Volumetric motion quantification by 3D tissue phase mapped CMR

    Directory of Open Access Journals (Sweden)

    Lutz Anja

    2012-10-01

    Full Text Available Abstract Background The objective of this study was the quantification of myocardial motion from 3D tissue phase mapped (TPM CMR. Recent work on myocardial motion quantification by TPM has been focussed on multi-slice 2D acquisitions thus excluding motion information from large regions of the left ventricle. Volumetric motion assessment appears an important next step towards the understanding of the volumetric myocardial motion and hence may further improve diagnosis and treatments in patients with myocardial motion abnormalities. Methods Volumetric motion quantification of the complete left ventricle was performed in 12 healthy volunteers and two patients applying a black-blood 3D TPM sequence. The resulting motion field was analysed regarding motion pattern differences between apical and basal locations as well as for asynchronous motion pattern between different myocardial segments in one or more slices. Motion quantification included velocity, torsion, rotation angle and strain derived parameters. Results All investigated motion quantification parameters could be calculated from the 3D-TPM data. Parameters quantifying hypokinetic or asynchronous motion demonstrated differences between motion impaired and healthy myocardium. Conclusions 3D-TPM enables the gapless volumetric quantification of motion abnormalities of the left ventricle, which can be applied in future application as additional information to provide a more detailed analysis of the left ventricular function.

  4. Video-rate volumetric optical coherence tomography-based microangiography

    Science.gov (United States)

    Baran, Utku; Wei, Wei; Xu, Jingjiang; Qi, Xiaoli; Davis, Wyatt O.; Wang, Ruikang K.

    2016-04-01

    Video-rate volumetric optical coherence tomography (vOCT) is relatively young in the field of OCT imaging but has great potential in biomedical applications. Due to the recent development of the MHz range swept laser sources, vOCT has started to gain attention in the community. Here, we report the first in vivo video-rate volumetric OCT-based microangiography (vOMAG) system by integrating an 18-kHz resonant microelectromechanical system (MEMS) mirror with a 1.6-MHz FDML swept source operating at ˜1.3 μm wavelength. Because the MEMS scanner can offer an effective B-frame rate of 36 kHz, we are able to engineer vOMAG with a video rate up to 25 Hz. This system was utilized for real-time volumetric in vivo visualization of cerebral microvasculature in mice. Moreover, we monitored the blood perfusion dynamics during stimulation within mouse ear in vivo. We also discussed this system's limitations. Prospective MEMS-enabled OCT probes with a real-time volumetric functional imaging capability can have a significant impact on endoscopic imaging and image-guided surgery applications.

  5. Bigravity from gradient expansion

    Energy Technology Data Exchange (ETDEWEB)

    Yamashita, Yasuho [Yukawa Institute for Theoretical Physics, Kyoto University,606-8502, Kyoto (Japan); Tanaka, Takahiro [Yukawa Institute for Theoretical Physics, Kyoto University,606-8502, Kyoto (Japan); Department of Physics, Kyoto University,606-8502, Kyoto (Japan)

    2016-05-04

    We discuss how the ghost-free bigravity coupled with a single scalar field can be derived from a braneworld setup. We consider DGP two-brane model without radion stabilization. The bulk configuration is solved for given boundary metrics, and it is substituted back into the action to obtain the effective four-dimensional action. In order to obtain the ghost-free bigravity, we consider the gradient expansion in which the brane separation is supposed to be sufficiently small so that two boundary metrics are almost identical. The obtained effective theory is shown to be ghost free as expected, however, the interaction between two gravitons takes the Fierz-Pauli form at the leading order of the gradient expansion, even though we do not use the approximation of linear perturbation. We also find that the radion remains as a scalar field in the four-dimensional effective theory, but its coupling to the metrics is non-trivial.

  6. Analysis of Changing Swarm Rate using Volumetric Strain

    Science.gov (United States)

    Kumazawa, T.; Ogata, Y.; Kimura, K.; Maeda, K.; Kobayashi, A.

    2015-12-01

    Near the eastern coast of Izu peninsula is an active submarine volcanic region in Japan, where magma intrusions have been observed many times. The forecast of earthquake swarm activities and eruptions are serious concern particularly in nearby hot spring resort areas. It is well known that temporal durations of the swarm activities have been correlated with early volumetric strain changes at a certain observation station of about 20 km distance apart. Therefore the Earthquake Research Committee (2010) investigated some empirical statistical relations to predict sizes of the swarm activity. Here we looked at the background seismicity rate changes during these swarm periods using the non-stationary ETAS model (Kumazawa and Ogata, 2013, 2014), and have found the followings. The modified volumetric strain data, by removing the effect of earth tides, precipitation and coseismic jumps, have significantly higher cross-correlations to the estimated background rates of the ETAS model than to the swarm rate-changes. Specifically, the background seismicity rate synchronizes clearer to the strain change by the lags around a half day. These relations suggest an enhanced prediction of earthquakes in this region using volumetric strain measurements. Hence we propose an extended ETAS model where the background rate is modulated by the volumetric strain data. We have also found that the response function to the strain data can be well approximated by an exponential functions with the same decay rate, but that their intersects are inversely proportional to the distances between the volumetric strain-meter and the onset location of the swarm. Our numerical results by the same proposed model show consistent outcomes for the various major swarms in this region.

  7. Thermal expansion in dysprosium tungstate Dy10W2O21

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    The complex oxide Dy10W2O21 was synthesized by a solid-state reaction and isolated in cubic symmetry by an X-ray diffractometry (XRD) method. Differential scanning calorimetry (DSC) measurements show that the compound is thermodynamically stable. The intrinsic thermal expansion coefficients were determined by extra-power powder Xray diffractometry from room temperature to 1000 ℃: linear coefficient α = 1.07 × 10-5 ℃-1 and bulk coefficient β=3.20 × 10-5℃-1. Dilatometry was used to measure the extrinsic thermal expansion coefficient (9.2 × 10-6℃-1).

  8. Translation of Bernstein Coefficients Under an Affine Mapping of the Unit Interval

    Science.gov (United States)

    Alford, John A., II

    2012-01-01

    We derive an expression connecting the coefficients of a polynomial expanded in the Bernstein basis to the coefficients of an equivalent expansion of the polynomial under an affine mapping of the domain. The expression may be useful in the calculation of bounds for multi-variate polynomials.

  9. Second- and Higher-Order Virial Coefficients Derived from Equations of State for Real Gases

    Science.gov (United States)

    Parkinson, William A.

    2009-01-01

    Derivation of the second- and higher-order virial coefficients for models of the gaseous state is demonstrated by employing a direct differential method and subsequent term-by-term comparison to power series expansions. This communication demonstrates the application of this technique to van der Waals representations of virial coefficients.…

  10. Comparing Visually Assessed BI-RADS Breast Density and Automated Volumetric Breast Density Software: A Cross-Sectional Study in a Breast Cancer Screening Setting.

    Directory of Open Access Journals (Sweden)

    Daniëlle van der Waal

    Full Text Available The objective of this study is to compare different methods for measuring breast density, both visual assessments and automated volumetric density, in a breast cancer screening setting. These measures could potentially be implemented in future screening programmes, in the context of personalised screening or screening evaluation.Digital mammographic exams (N = 992 of women participating in the Dutch breast cancer screening programme (age 50-75y in 2013 were included. Breast density was measured in three different ways: BI-RADS density (5th edition and with two commercially available automated software programs (Quantra and Volpara volumetric density. BI-RADS density (ordinal scale was assessed by three radiologists. Quantra (v1.3 and Volpara (v1.5.0 provide continuous estimates. Different comparison methods were used, including Bland-Altman plots and correlation coefficients (e.g., intraclass correlation coefficient [ICC].Based on the BI-RADS classification, 40.8% of the women had 'heterogeneously or extremely dense' breasts. The median volumetric percent density was 12.1% (IQR: 9.6-16.5 for Quantra, which was higher than the Volpara estimate (median 6.6%, IQR: 4.4-10.9. The mean difference between Quantra and Volpara was 5.19% (95% CI: 5.04-5.34 (ICC: 0.64. There was a clear increase in volumetric percent dense volume as BI-RADS density increased. The highest accuracy for predicting the presence of BI-RADS c+d (heterogeneously or extremely dense was observed with a cut-off value of 8.0% for Volpara and 13.8% for Quantra.Although there was no perfect agreement, there appeared to be a strong association between all three measures. Both volumetric density measures seem to be usable in breast cancer screening programmes, provided that the required data flow can be realized.

  11. From Free Expansion to Abrupt Compression of an Ideal Gas

    Science.gov (United States)

    Anacleto, Joaquim; Pereira, Mario G.

    2009-01-01

    Using macroscopic thermodynamics, the general law for adiabatic processes carried out by an ideal gas was studied. It was shown that the process reversibility is characterized by the adiabatic reversibility coefficient r, in the range 0 [less than or equal] r [less than or equal] 1 for expansions and r [greater than or equal] 1 for compressions.…

  12. Modeling urban expansion by using variable weights logistic cellular automata

    NARCIS (Netherlands)

    Shu, Bangrong; Bakker, Martha M.; Zhang, Honghui; Li, Yongle; Qin, Wei; Carsjens, Gerrit J.

    2017-01-01

    Simulation models based on cellular automata (CA) are widely used for understanding and simulating complex urban expansion process. Among these models, logistic CA (LCA) is commonly adopted. However, the performance of LCA models is often limited because the fixed coefficients obtained from binary

  13. From Free Expansion to Abrupt Compression of an Ideal Gas

    Science.gov (United States)

    Anacleto, Joaquim; Pereira, Mario G.

    2009-01-01

    Using macroscopic thermodynamics, the general law for adiabatic processes carried out by an ideal gas was studied. It was shown that the process reversibility is characterized by the adiabatic reversibility coefficient r, in the range 0 [less than or equal] r [less than or equal] 1 for expansions and r [greater than or equal] 1 for compressions.…

  14. Legendre Expansions for Two-Hadron Reactions

    Science.gov (United States)

    Strakovsky, Igor; Azimov, Yakov; Briscoe, William

    2017-01-01

    Modern experimental facilities and detectors provide tremendous volumes of detailed data. For two-hadron reactions, they are usually presented as a set of multiple panels, e . g . , angular distributions at many particular energies. Such presentations lose visuality, and their physical content may be extracted only through some model-dependent treatment. Instead, we suggest to use expansion into the Legendre series with a relatively small number of essential coefficients. This approach was applied in several experimental investigations and demonstrated its higher visualization. This talk presents some general properties of the Legendre coefficients which allow one to extract physical information even without any model-dependent assumptions. The U.S. Department of Energy, Office of Science, Office of Nuclear Physics, Award Numbers DE-SC0014133 and DE-SC0016582 and the Russian Science Foundation, Award No.14-22-00281.

  15. Sabine absorption coefficients to random incidence absorption coefficients

    DEFF Research Database (Denmark)

    Jeong, Cheol-Ho

    2014-01-01

    Absorption coefficients measured by the chamber method are referred to as Sabine absorption coefficients, which sometimes exceed unity due to the finite size of a specimen and non-uniform intensity in the test chamber. In this study, several methods that convert Sabine absorption coefficients...... into random incidence absorption coefficients for porous absorbers are investigated. Two optimization-based conversion methods are suggested: the surface impedance estimation for locally reacting absorbers and the flow resistivity estimation for extendedly reacting absorbers. The suggested conversion methods...

  16. Constructing Cross-Linked Polymer Networks Using Monte Carlo Simulated Annealing Technique for Atomistic Molecular Simulations

    Science.gov (United States)

    2014-10-01

    of these networks, the specific volume and the coefficient of volumetric thermal expansion (CVTE), are shown in Fig. 4. Specific volume is...CVTE values are somewhat lower than expected from experimental measurements of the coefficient of linear thermal expansion ,27 which can be...coefficient of volumetric thermal expansion db equilibrium bond length DCPD dicyclopentadiene GAFF general AMBER force field ID identification K

  17. Controllable rectification of the axial expansion in the thermally driven artificial muscle

    Science.gov (United States)

    Yue, Donghua; Zhang, Xingyi; Yong, Huadong; Zhou, Jun; Zhou, You-He

    2015-09-01

    At present, the concept of artificial muscle twisted by polymers or fibers has become a hot issue in the field of intelligent material research according to its distinguishing advantages, e.g., high energy density, large-stroke, non-hysteresis, and inexpensive. The axial thermal expansion coefficient is an important parameter which can affect its demanding applications. In this letter, a device with high accuracy capacitive sensor is constructed to measure the axial thermal expansion coefficient of the twisted carbon fibers and yarns of Kevlar, and a theoretical model based on the thermal elasticity and the geometrical features of the twisted structure are also presented to predict the axial expansion coefficient. It is found that the calculated results take good agreements with the experimental data. According to the present experiment and analyses, a method to control the axial thermal expansion coefficient of artificial muscle is proposed. Moreover, the mechanism of this kind of thermally driven artificial muscle is discussed.

  18. Elastic and thermal expansion asymmetry in dense molecular materials.

    Science.gov (United States)

    Burg, Joseph A; Dauskardt, Reinhold H

    2016-09-01

    The elastic modulus and coefficient of thermal expansion are fundamental properties of elastically stiff molecular materials and are assumed to be the same (symmetric) under both tension and compression loading. We show that molecular materials can have a marked asymmetric elastic modulus and coefficient of thermal expansion that are inherently related to terminal chemical groups that limit molecular network connectivity. In compression, terminal groups sterically interact to stiffen the network, whereas in tension they interact less and disconnect the network. The existence of asymmetric elastic and thermal expansion behaviour has fundamental implications for computational approaches to molecular materials modelling and practical implications on the thermomechanical strains and associated elastic stresses. We develop a design space to control the degree of elastic asymmetry in molecular materials, a vital step towards understanding their integration into device technologies.

  19. Low temperature thermal expansion measurements on optical materials.

    Science.gov (United States)

    Browder, J S; Ballard, S S

    1969-04-01

    A three-terminal capacitance type dilatometer has been developed for investigating the thermal expansion of optical materials at low temperatures. The method is applicable when only small sample lengths (13 mm or less) are available. The thermal expansion coefficients of six polycrystalline materials (the Irtrans) and of one nonoxide glass have been determined in the range from room temperature down to about 60 K. Minute changes of the length of a sample produce a change of the spacing of a parallel plate capacitor with guard ring; the resulting change of capacitance is measured on a highly sensitive bridge. The expansion coefficients are then determined by relating the change of capacitance to the change of dimensions of the sample.

  20. Elastic and thermal expansion asymmetry in dense molecular materials

    Science.gov (United States)

    Burg, Joseph A.; Dauskardt, Reinhold H.

    2016-09-01

    The elastic modulus and coefficient of thermal expansion are fundamental properties of elastically stiff molecular materials and are assumed to be the same (symmetric) under both tension and compression loading. We show that molecular materials can have a marked asymmetric elastic modulus and coefficient of thermal expansion that are inherently related to terminal chemical groups that limit molecular network connectivity. In compression, terminal groups sterically interact to stiffen the network, whereas in tension they interact less and disconnect the network. The existence of asymmetric elastic and thermal expansion behaviour has fundamental implications for computational approaches to molecular materials modelling and practical implications on the thermomechanical strains and associated elastic stresses. We develop a design space to control the degree of elastic asymmetry in molecular materials, a vital step towards understanding their integration into device technologies.

  1. Measuring thermal expansion using X-band persistent scatterer interferometry

    Science.gov (United States)

    Crosetto, Michele; Monserrat, Oriol; Cuevas-González, María; Devanthéry, Núria; Luzi, Guido; Crippa, Bruno

    2015-02-01

    This paper is focused on the estimation of the thermal expansion of buildings and infrastructures using X-band Persistent Scatterer Interferometry (PSI) observations. For this purpose an extended PSI model is used, which allows separating the thermal expansion from the total observed deformation thus generating a new PSI product: the map of the thermal expansion parameter, named thermal map. The core of the paper is devoted to the exploitation of the information contained in the thermal maps: three examples are discussed in detail, which concern a viaduct, a set of industrial buildings and two skyscrapers. The thermal maps can be used to derive the thermal expansion coefficient of the observed objects and information on their static structure. In addition, the paper illustrates the distortions in the PSI deformation products that occur if the thermal expansion is not explicitly modelled. Finally, an inter-comparison exercise is described, where the thermal expansion coefficients estimated by PSI are compared with those derived by a Ku-band ground-based SAR campaign.

  2. Strong anisotropic thermal expansion in cristobalite-type BPO 4

    Science.gov (United States)

    Achary, S. N.; Tyagi, A. K.

    2004-11-01

    In this communication, the thermal expansion behavior of cristobalite-type BPO 4, determined from high-temperature X-ray diffraction studies, is being reported. BPO 4 crystallizes in tetragonal lattice, with space group I-4 (No. 82) at room temperature, with unit cell parameters: a=4.3447(2), c=6.6415(5) Å and V=125.37(1) Å 3. The tetragonal unit cell parameters at 900 °C are: a=4.3939(2), c=6.6539(6) Å and V=128.46(1) Å 3. The results show a very strong anisotropic expansion in the lattice, with the typical thermal expansion coefficients along a- and c-axis 12.9×10 -6 and 2.1×10 -6/°C, respectively. The volume thermal expansion coefficient of the lattice is 28.2×10 -6/°C in the temperature range of 25-900 °C. The variation of the crystal structure with temperature and the thermal expansion behavior are explained in this manuscript. The role of inter-polyhedral angle on the thermal expansion behavior has also been established.

  3. Thermal expansion behaviour of Long-Period Stacking Ordered (LPSO) phase

    Energy Technology Data Exchange (ETDEWEB)

    Garces, G.; Requena, G.; Tolnai, D.; Perez, P.; Adeva, P.; Jimenez, J. A.; Stark, A.; Schell, N.

    2015-07-01

    The lineal thermal expansion coefficient of the 18R Long-Period Stacking Ordered (LPSO) structure was determined in the range between room temperature and 400 degree centigrade by dilatometry and synchrotron radiation diffraction. Results clearly show that the lineal thermal expansion coefficients for magnesium and the LPSO phase are similar and therefore no mismatch thermal stresses are generated at their interface in two-phase Mg-Y-Zn alloys containing this phase during thermomechanical processing. (Author)

  4. Conformal invariant Painlevé expansions and higher dimensional integrable models

    Institute of Scientific and Technical Information of China (English)

    楼森岳

    1999-01-01

    After the (1+1)-dimensional nonlinear Schr(?)dinger equation is embedded in higher dimensions and the usual singularity analysis approach is extended such that all the Painlev(?) expansion coefficients are conformal invariant, many higher dimensional integrable models are got after the nontrivial conformal invariant expansion coefficients are taken to be zero simply. The Painlev(?) properties of the obtained higher dimensional models (including some (3+1)-dimensional models) are proved.

  5. Partially linear varying coefficient models stratified by a functional covariate

    KAUST Repository

    Maity, Arnab

    2012-10-01

    We consider the problem of estimation in semiparametric varying coefficient models where the covariate modifying the varying coefficients is functional and is modeled nonparametrically. We develop a kernel-based estimator of the nonparametric component and a profiling estimator of the parametric component of the model and derive their asymptotic properties. Specifically, we show the consistency of the nonparametric functional estimates and derive the asymptotic expansion of the estimates of the parametric component. We illustrate the performance of our methodology using a simulation study and a real data application.

  6. Calculation of self-diffusion coefficients in iron

    Directory of Open Access Journals (Sweden)

    Baohua Zhang

    2014-01-01

    Full Text Available On the basis of available P-V-T equation of state of iron, the temperature and pressure dependence of self-diffusion coefficients in iron polymorphs (α, δ, γ and ɛ phases have been successfully reproduced in terms of the bulk elastic and expansivity data by means of a thermodynamical model that interconnects point defects parameters with bulk properties. The calculated diffusion parameters, such as self-diffusion coefficient, activation energy and activation volume over a broad temperature range (500-2500 K and pressure range (0-100 GPa, compare favorably well with experimental or theoretical ones when the uncertainties are considered.

  7. Partially Linear Varying Coefficient Models Stratified by a Functional Covariate.

    Science.gov (United States)

    Maity, Arnab; Huang, Jianhua Z

    2012-10-01

    We consider the problem of estimation in semiparametric varying coefficient models where the covariate modifying the varying coefficients is functional and is modeled nonparametrically. We develop a kernel-based estimator of the nonparametric component and a profiling estimator of the parametric component of the model and derive their asymptotic properties. Specifically, we show the consistency of the nonparametric functional estimates and derive the asymptotic expansion of the estimates of the parametric component. We illustrate the performance of our methodology using a simulation study and a real data application.

  8. Coefficient Alpha: A Reliability Coefficient for the 21st Century?

    Science.gov (United States)

    Yang, Yanyun; Green, Samuel B.

    2011-01-01

    Coefficient alpha is almost universally applied to assess reliability of scales in psychology. We argue that researchers should consider alternatives to coefficient alpha. Our preference is for structural equation modeling (SEM) estimates of reliability because they are informative and allow for an empirical evaluation of the assumptions…

  9. Measuring of heat transfer coefficient

    DEFF Research Database (Denmark)

    Henningsen, Poul; Lindegren, Maria

    Subtask 3.4 Measuring of heat transfer coefficient Subtask 3.4.1 Design and setting up of tests to measure heat transfer coefficient Objective: Complementary testing methods together with the relevant experimental equipment are to be designed by the two partners involved in order to measure...... the heat transfer coefficient for a wide range of interface conditions in hot and warm forging processes. Subtask 3.4.2 Measurement of heat transfer coefficient The objective of subtask 3.4.2 is to determine heat transfer values for different interface conditions reflecting those typically operating in hot...

  10. Measuring of heat transfer coefficient

    DEFF Research Database (Denmark)

    Henningsen, Poul; Lindegren, Maria

    Subtask 3.4 Measuring of heat transfer coefficient Subtask 3.4.1 Design and setting up of tests to measure heat transfer coefficient Objective: Complementary testing methods together with the relevant experimental equipment are to be designed by the two partners involved in order to measure...... the heat transfer coefficient for a wide range of interface conditions in hot and warm forging processes. Subtask 3.4.2 Measurement of heat transfer coefficient The objective of subtask 3.4.2 is to determine heat transfer values for different interface conditions reflecting those typically operating in hot...

  11. Unravelling the fundamentals of thermal and chemical expansion of BaCeO3 from first principles phonon calculations.

    Science.gov (United States)

    Løken, Andreas; Haugsrud, Reidar; Bjørheim, Tor S

    2016-11-16

    Differentiating chemical and thermal expansion is virtually impossible to achieve experimentally. While thermal expansion stems from a softening of the phonon spectra, chemical expansion depends on the chemical composition of the material. In the present contribution, we, for the first time, completely decouple thermal and chemical expansion through first principles phonon calculations on BaCeO3, providing new fundamental insights to lattice expansion. We assess the influence of defects on thermal expansion, and how this in turn affects the interpretation of chemical expansion and defect thermodynamics. The calculations reveal that the linear thermal expansion coefficient is lowered by the introduction of oxygen vacancies being 10.6 × 10(-6) K(-1) at 300 K relative to 12.2 × 10(-6) K(-1) for both the protonated and defect-free bulk lattice. We further demonstrate that the chemical expansion coefficient upon hydration varies with temperature, ranging from 0.070 to 0.115 per mole oxygen vacancy. Ultimately, we find that, due to differences in the thermal expansion coefficients under dry and wet conditions, the chemical expansion coefficients determined experimentally are grossly underestimated - around 55% lower in the case of 10 mol% acceptor doped BaCeO3. Lastly, we evaluate the effect of these volume changes on the vibrational thermodynamics.

  12. Testing Machine for Expansive Mortar

    CERN Document Server

    Silva, Romulo Augusto Ventura

    2011-01-01

    The correct evaluation of a material property is fundamental to, on their application; they met all expectations that were designed for. In development of an expansive cement for ornamental rocks purpose, was denoted the absence of methodologies and equipments to evaluate the expansive pressure and temperature of expansive cement during their expansive process, having that data collected in a static state of the specimen. In that paper, is described equipment designed for evaluation of pressure and temperature of expansive cements applied to ornamental rocks.

  13. Engineering Properties of Expansive Soil

    Institute of Scientific and Technical Information of China (English)

    DAI Shaobin; SONG Minghai; HUANG Jun

    2005-01-01

    The components of expansive soil were analyzed with EDAX, and it is shown that the main contents of expansive soil in the northern Hubei have some significant effects on engineering properties of expansive soil. Furthermore, the soil modified by lime has an obvious increase of Ca2+ and an improvement of connections between granules so as to reduce the expansibility and contractility of soil. And it also has a better effect on the modified expansive soil than the one modified by pulverized fuel ash.

  14. Second virial coefficient for the dipolar hard sphere fluid.

    Science.gov (United States)

    Henderson, Douglas

    2011-07-28

    The dipolar hard sphere fluid is a useful model for a polar fluid. Some years ago, the second virial coefficient, B(2), of this fluid was obtained as a series expansion in the inverse temperature or (dipole strength) by Keesom. Little work on this problem seems to have been done since that time. Using a result of Chan and Henderson for the spherical average of the Boltzmann factor of this fluid, more complete results are obtained for B(2). The more complete results are more negative than the Keesom series, as one would expect, but his expansion is remarkably accurate. This method can be used to obtain the second virial coefficient of the dipolar Lennard-Jones (Stockmayer) or dipolar Yukawa fluids.

  15. Relativistic quantum transport coefficients for second-order viscous hydrodynamics

    CERN Document Server

    Florkowski, Wojciech; Maksymiuk, Ewa; Ryblewski, Radoslaw; Strickland, Michael

    2015-01-01

    We express the transport coefficients appearing in the second-order evolution equations for bulk viscous pressure and shear stress tensor using Bose-Einstein, Boltzmann, and Fermi-Dirac statistics for the equilibrium distribution function and Grad's 14-moment approximation as well as the method of Chapman-Enskog expansion for the non-equilibrium part. Specializing to the case of boost-invariant and transversally homogeneous longitudinal expansion of the viscous medium, we compare the results obtained using the above methods with those obtained from the exact solution of massive 0+1d Boltzmann equation in the relaxation-time approximation. We show that compared to the 14-moment approximation, the hydrodynamic transport coefficients obtained using the Chapman-Enskog method result in better agreement with the exact solution of the Boltzmann equation in relaxation-time approximation.

  16. Soliton solutions of the generalized sinh-Gordon equation by the binary (′/)-expansion method

    Indian Academy of Sciences (India)

    A Neirameh

    2015-10-01

    The aim of this paper is to extend the applications of (′/)-expansion method to solve a generalized sinh-Gordon equation. In fact, the binary (′/)-expansion method is introduced for finding different new exact solutions. It is shown that this method is a powerful mathematical tool for solving nonlinear evolution equations with time-dependent coefficients in mathematical physics.

  17. Parallel optical Walsh expansion in a pattern recognition preprocessor using planar microlens array

    Science.gov (United States)

    Murashige, Kimio; Akiba, Atsushi; Baba, Toshihiko; Iga, Kenichi

    1992-05-01

    A parallel optical processor developed for a pattern recognition system using a planar microlens array and a Walsh orthogonal expansion spatial filter is developed. The parallel optical Walsh expansion of multiple images made by the planar microlens array with good accuracy, which assures 99-percent recognition of simple numeral characters in the system, is demonstrated. A novel selection method of Walsh expansion coefficients is proposed in order to enlarge the tolerance of the recognition rate against the deformation of input patterns.

  18. Resonant-state expansion of light propagation in non-uniform waveguides

    OpenAIRE

    Lobanov, S. V.; Zoriniants, G.; Langbein, W.; Muljarov, E. A.

    2016-01-01

    A new rigorous approach for precise and efficient calculation of light propagation along non-uniform waveguides is presented. Resonant states of a uniform waveguide, which satisfy outgoing-wave boundary conditions, form a natural basis for expansion of the local electromagnetic field. Using such an expansion at fixed frequency, we convert the light propagation along a non-uniform waveguide into an ordinary second-order matrix differential equation for the expansion coefficients along the wave...

  19. Colossal negative thermal expansion in reduced layered ruthenate

    Science.gov (United States)

    Takenaka, Koshi; Okamoto, Yoshihiko; Shinoda, Tsubasa; Katayama, Naoyuki; Sakai, Yuki

    2017-01-01

    Large negative thermal expansion (NTE) has been discovered during the last decade in materials of various kinds, particularly materials associated with a magnetic, ferroelectric or charge-transfer phase transition. Such NTE materials have attracted considerable attention for use as thermal-expansion compensators. Here, we report the discovery of giant NTE for reduced layered ruthenate. The total volume change related to NTE reaches 6.7% in dilatometry, a value twice as large as the largest volume change reported to date. We observed a giant negative coefficient of linear thermal expansion α=-115 × 10-6 K-1 over 200 K interval below 345 K. This dilatometric NTE is too large to be attributable to the crystallographic unit-cell volume variation with temperature. The highly anisotropic thermal expansion of the crystal grains might underlie giant bulk NTE via microstructural effects consuming open spaces in the sintered body on heating.

  20. Impact of size and temperature on thermal expansion of nanomaterials

    Indian Academy of Sciences (India)

    Madan Singh; Mahipal Singh

    2015-04-01

    A theoretical method has been discussed to study the size dependency of thermal expansion of nanomaterials at higher temperature by considering the surface effect. A thermodynamical analysis of the equation of state (EoS) is studied from the knowledge of thermal expansion of nano-materials based on theoretical thermodynamical relations. It is observed that thermal expansion coefficient increases with decrease in grain size whereas, /0 increases with increase in temperature for nanomaterials of different grain sizes. We have studied the size and temperature dependence of thermal expansion of Cu, Ag, Ni, Sn, Se and Zn nanomaterials in different shapes (spherical, nanowire and nanofilm). The available experimental data confirm these theoretical predictions that demonstrate the validity of our work.

  1. Volumetric, ultrasonic speed, and viscometric studies of salbutamol sulphate in aqueous methanol solution at different temperatures

    Energy Technology Data Exchange (ETDEWEB)

    Rajagopal, K., E-mail: krpal25@yahoo.co [Department of Physics, Government College of Engineering, Tirunelveli 627 007, Tamil Nadu (India); Jayabalakrishnan, S.S., E-mail: krishnanpsr@yahoo.co [Department of Physics, P.S.R. Engineering College, Sivakasi 626 140, Tamil Nadu (India)

    2010-08-15

    Values of density, ultrasonic speed, and viscosity of salbutamol sulphate (SBS) have been determined in aqueous methanol solutions at T = (303.15, 308.15, 313.15, and 318.15) K. The apparent molar volume V{sub {phi}}, partial molar volume V{sub {phi}}{sup 0}, molar expansivity E{sub 2}{sup 0}, isobaric thermal expansion coefficient ({alpha}{sub 2}), and second derivative of infinite dilution of partial molar volume with temperature {partial_derivative}{sup 2}V{sub {phi}}{sup 0}/{partial_derivative}T{sup 2} are evaluated using density data. Isentropic compressibility {beta}{sub s}, change in isothermal compressibility {Delta}{beta}{sub s}, relative change in isentropic compressibility ({Delta}{beta}{sub s}/{beta}{sub s}{sup 0}), apparent molar compressibility K{sub {phi}}and partial molar compressibility K{sub {phi}}{sup 0} values are calculated by using data on density with ultrasonic speed. Viscosity B-coefficient, variation of B-coefficient with temperature, i.e.,dB/dT, free energy of activation per mole of solvent {Delta}{mu}{sub 1}{sup 0*} and solute {Delta}{mu}{sub 2}{sup 0*} are evaluated using viscosity data. The above parameters are used to interpret the solute-solute, solute-solvent interactions and structure making/breaking ability of the drug in the given aqueous methanol solution.

  2. Exploring non-linear cosmological matter diffusion coefficients

    CERN Document Server

    Velten, Hermano

    2014-01-01

    Since microscopic velocity diffusion can be incorporated into general relativity in a consistent way, we study cosmological background solutions when the diffusion phenomena takes place in an expanding universe. Our focus here relies on the nature of the diffusion coefficient $\\sigma$ which measures the magnitude of such transport phenomena. We test dynamics where $\\sigma$ has a phenomenological dependence on the scale factor, the matter density, the dark energy and the expansion rate.

  3. Thermal expansion of glasses at low temperatures

    Energy Technology Data Exchange (ETDEWEB)

    Lyon, K.G.

    1979-01-01

    The linear thermal expansion coefficient (..cap alpha.. = (par. deltalnL/par. deltaT)/sub p/) was measured at temperatures to 1.2K for two amorphous solids, fused silica and PMMA (polymethylmethacrylate, plexiglas), using a parallel plate capacitor differential dilatometer. The low temperature expansion coefficients for these solids have the same temperature dependences as the specific heats, and show a contribution which is linear in the temperature and which can be associated with the postulate of a broad distribution of two level states. The Grueneisen parameters which are associated with this contribution are comparable for the two solids (Y approx. = -16), and suggest a further indication of common behavior for amorphous solids at low temperature. Large magnitudes for Grueneisen parameters (/..gamma../ > 5) generally are associated with tunneling models. A symmetric double harmonic oscillator tunneling model can be used to understand the sign and magnitude of ..gamma.. for these solids. This model is inconsistent with other thermal and thermodynamic data for fused silica. The existence of similar negative and large magnitude Grueneisen parameters for these two amorphous solids places an additional constraint on theories for the low temperature properties of glasses.

  4. Pulse sequence for dynamic volumetric imaging of hyperpolarized metabolic products

    Science.gov (United States)

    Cunningham, Charles H.; Chen, Albert P.; Lustig, Michael; Hargreaves, Brian A.; Lupo, Janine; Xu, Duan; Kurhanewicz, John; Hurd, Ralph E.; Pauly, John M.; Nelson, Sarah J.; Vigneron, Daniel B.

    2008-07-01

    Dynamic nuclear polarization and dissolution of a 13C-labeled substrate enables the dynamic imaging of cellular metabolism. Spectroscopic information is typically acquired, making the acquisition of dynamic volumetric data a challenge. To enable rapid volumetric imaging, a spectral-spatial excitation pulse was designed to excite a single line of the carbon spectrum. With only a single resonance present in the signal, an echo-planar readout trajectory could be used to resolve spatial information, giving full volume coverage of 32 × 32 × 16 voxels every 3.5 s. This high frame rate was used to measure the different lactate dynamics in different tissues in a normal rat model and a mouse model of prostate cancer.

  5. Nonrigid registration of volumetric images using ranked order statistics

    DEFF Research Database (Denmark)

    Tennakoon, Ruwan; Bab-Hadiashar, Alireza; Cao, Zhenwei

    2014-01-01

    Non-rigid image registration techniques using intensity based similarity measures are widely used in medical imaging applications. Due to high computational complexities of these techniques, particularly for volumetric images, finding appropriate registration methods to both reduce the computation...... burden and increase the registration accuracy has become an intensive area of research. In this paper we propose a fast and accurate non-rigid registration method for intra-modality volumetric images. Our approach exploits the information provided by an order statistics based segmentation method, to find...... the important regions for registration and use an appropriate sampling scheme to target those areas and reduce the registration computation time. A unique advantage of the proposed method is its ability to identify the point of diminishing returns and stop the registration process. Our experiments...

  6. Volumetric characterization of delamination fields via angle longitudinal wave ultrasound

    Science.gov (United States)

    Wertz, John; Wallentine, Sarah; Welter, John; Dierken, Josiah; Aldrin, John

    2017-02-01

    The volumetric characterization of delaminations necessarily precedes rigorous composite damage progression modeling. Yet, inspection of composite structures for subsurface damage remains largely focused on detection, resulting in a capability gap. In response to this need, angle longitudinal wave ultrasound was employed to characterize a composite surrogate containing a simulated three-dimensional delamination field with distinct regions of occluded features (shadow regions). Simple analytical models of the specimen were developed to guide subsequent experimentation through identification of optimal scanning parameters. The ensuing experiments provided visual evidence of the complete delamination field, including indications of features within the shadow regions. The results of this study demonstrate proof-of-principle for the use of angle longitudinal wave ultrasonic inspection for volumetric characterization of three-dimensional delamination fields. Furthermore, the techniques developed herein form the foundation of succeeding efforts to characterize impact delaminations within inhomogeneous laminar materials such as polymer matrix composites.

  7. Magnetic Resonance Image Segmentation and its Volumetric Measurement

    Directory of Open Access Journals (Sweden)

    Rahul R. Ambalkar

    2013-02-01

    Full Text Available Image processing techniques make it possible to extract meaningful information from medical images. Magnetic resonance (MR imaging has been widely applied in biological research and diagnostics because of its excellent soft tissue contrast, non-invasive character, high spatial resolution and easy slice selection at any orientation. The MRI-based brain volumetric is concerned with the analysis of volumes and shapes of the structural components of the human brain. It also provides a criterion, by which we recognize the presence of degenerative diseases and characterize their rates of progression to make the diagnosis and treatments as a easy task. In this paper we have proposed an automated method for volumetric measurement of Magnetic Resonance Imaging and used Self Organized Map (SOM clustering method for their segmentations. We have used the MRI data set of 61 slices of 256×256 pixels in DICOM standard format

  8. Two-dimensional random arrays for real time volumetric imaging

    DEFF Research Database (Denmark)

    Davidsen, Richard E.; Jensen, Jørgen Arendt; Smith, Stephen W.

    1994-01-01

    Two-dimensional arrays are necessary for a variety of ultrasonic imaging techniques, including elevation focusing, 2-D phase aberration correction, and real time volumetric imaging. In order to reduce system cost and complexity, sparse 2-D arrays have been considered with element geometries...... real time volumetric imaging system, which employs a wide transmit beam and receive mode parallel processing to increase image frame rate. Depth-of-field comparisons were made from simulated on-axis and off-axis beamplots at ranges from 30 to 160 mm for both coaxial and offset transmit and receive...... selected ad hoc, by algorithm, or by random process. Two random sparse array geometries and a sparse array with a Mills cross receive pattern were simulated and compared to a fully sampled aperture with the same overall dimensions. The sparse arrays were designed to the constraints of the Duke University...

  9. In Vivo Real Time Volumetric Synthetic Aperture Ultrasound Imaging

    DEFF Research Database (Denmark)

    Bouzari, Hamed; Rasmussen, Morten Fischer; Brandt, Andreas Hjelm

    2015-01-01

    . This paper investigates the in vivo applicability and sensitivity of volumetric SA imaging. Utilizing the transmit events to generate a set of virtual point sources, a frame rate of 25 Hz for a 90° x 90° field-of-view was achieved. Data were obtained using a 3.5 MHz 32 x 32 elements 2-D phased array......Synthetic aperture (SA) imaging can be used to achieve real-time volumetric ultrasound imaging using 2-D array transducers. The sensitivity of SA imaging is improved by maximizing the acoustic output, but one must consider the limitations of an ultrasound system, both technical and biological...... transducer connected to the experimental scanner (SARUS). Proper scaling is applied to the excitation signal such that intensity levels are in compliance with the U.S. Food and Drug Administration regulations for in vivo ultrasound imaging. The measured Mechanical Index and spatial-peak- temporal...

  10. COMPARISON OF VOLUMETRIC REGISTRATION ALGORITHMS FOR TENSOR-BASED MORPHOMETRY

    Science.gov (United States)

    Villalon, Julio; Joshi, Anand A.; Toga, Arthur W.; Thompson, Paul M.

    2015-01-01

    Nonlinear registration of brain MRI scans is often used to quantify morphological differences associated with disease or genetic factors. Recently, surface-guided fully 3D volumetric registrations have been developed that combine intensity-guided volume registrations with cortical surface constraints. In this paper, we compare one such algorithm to two popular high-dimensional volumetric registration methods: large-deformation viscous fluid registration, formulated in a Riemannian framework, and the diffeomorphic “Demons” algorithm. We performed an objective morphometric comparison, by using a large MRI dataset from 340 young adult twin subjects to examine 3D patterns of correlations in anatomical volumes. Surface-constrained volume registration gave greater effect sizes for detecting morphometric associations near the cortex, while the other two approaches gave greater effects sizes subcortically. These findings suggest novel ways to combine the advantages of multiple methods in the future. PMID:26925198

  11. Volumetric 3D display using a DLP projection engine

    Science.gov (United States)

    Geng, Jason

    2012-03-01

    In this article, we describe a volumetric 3D display system based on the high speed DLPTM (Digital Light Processing) projection engine. Existing two-dimensional (2D) flat screen displays often lead to ambiguity and confusion in high-dimensional data/graphics presentation due to lack of true depth cues. Even with the help of powerful 3D rendering software, three-dimensional (3D) objects displayed on a 2D flat screen may still fail to provide spatial relationship or depth information correctly and effectively. Essentially, 2D displays have to rely upon capability of human brain to piece together a 3D representation from 2D images. Despite the impressive mental capability of human visual system, its visual perception is not reliable if certain depth cues are missing. In contrast, volumetric 3D display technologies to be discussed in this article are capable of displaying 3D volumetric images in true 3D space. Each "voxel" on a 3D image (analogous to a pixel in 2D image) locates physically at the spatial position where it is supposed to be, and emits light from that position toward omni-directions to form a real 3D image in 3D space. Such a volumetric 3D display provides both physiological depth cues and psychological depth cues to human visual system to truthfully perceive 3D objects. It yields a realistic spatial representation of 3D objects and simplifies our understanding to the complexity of 3D objects and spatial relationship among them.

  12. Forecasting Urban Expansion Based on Night Lights

    Science.gov (United States)

    Stathakis, D.

    2016-06-01

    Forecasting urban expansion models are a very powerful tool in the hands of urban planners in order to anticipate and mitigate future urbanization pressures. In this paper, a linear regression forecasting urban expansion model is implemented based on the annual composite night lights time series available from National Oceanic and Atmospheric Administration (NOAA). The product known as 'stable lights' is used in particular, after it has been corrected with a standard intercalibration process to reduce artificial year-to-year fluctuations as much as possible. Forecasting is done for ten years after the end of the time series. Because the method is spatially explicit the predicted expansion trends are relatively accurately mapped. Two metrics are used to validate the process. The first one is the year-to-year Sum of Lights (SoL) variation. The second is the year-to-year image correlation coefficient. Overall it is evident that the method is able to provide an insight on future urbanization pressures in order to be taken into account in planning. The trends are quantified in a clear spatial manner.

  13. Expansion Compression Contacts for Thermoelectric Legs

    Science.gov (United States)

    Sakamoto, Jeffrey

    2009-01-01

    In a proposed alternative to previous approaches to making hot-shoe contacts to the legs of thermoelectric devices, one relies on differential thermal expansion to increase contact pressures for the purpose of reducing the electrical resistances of contacts as temperatures increase. The proposed approach is particularly applicable to thermoelectric devices containing p-type (positive-charge-carrier) legs made of a Zintl compound (specifically, Yb14MnSb11) and n-type (negative charge-carrier) legs made of SiGe. This combination of thermoelectric materials has been selected for further development, primarily on the basis of projected thermoelectric performance. However, it is problematic to integrate, into a practical thermoelectric device, legs made of these materials along with a metal or semiconductor hot shoe that is required to be in thermal and electrical contact with the legs. This is partly because of the thermal-expansion mismatch of these materials: The coefficient of thermal expansion (CTE) of SiGe is 4.5 x 10(exp -6) C (exp -1), while the CTE of Yb14MnSb11 is 20 x 10(exp -6) C(exp -1). Simply joining a Yb14MnSb11 and a SiGe leg to a common hot shoe could be expected to result in significant thermal stresses in either or both legs during operation. Heretofore, such thermal stresses have been regarded as disadvantageous. In the proposed approach, stresses resulting from the CTE mismatch would be turned to advantage.

  14. Effectively control negative thermal expansion of single-phase ferroelectrics of PbTiO3-(Bi,La)FeO3 over a giant range

    OpenAIRE

    Chen, Jun; Wang, Fangfang; Huang, Qingzhen; Hu, Lei; Song, Xiping; Deng, Jinxia; Yu, Ranbo; Xing, Xianran

    2013-01-01

    Control of negative thermal expansion is a fundamentally interesting topic in the negative thermal expansion materials in order for the future applications. However, it is a challenge to control the negative thermal expansion in individual pure materials over a large scale. Here, we report an effective way to control the coefficient of thermal expansion from a giant negative to a near zero thermal expansion by means of adjusting the spontaneous volume ferroelectrostriction (SVFS) in the syste...

  15. Using surface heave to estimate reservoir volumetric strain

    Energy Technology Data Exchange (ETDEWEB)

    Nanayakkara, A.S.; Wong, R.C.K. [Calgary Univ., AB (Canada)

    2008-07-01

    This paper presented a newly developed numerical tool for estimating reservoir volumetric strain distribution using surface vertical displacements and solving an inverse problem. Waterflooding, steam injection, carbon dioxide sequestration and aquifer storage recovery are among the subsurface injection operations that are responsible for reservoir dilations which propagate to the surrounding formations and extend to the surface resulting in surface heaves. Global positioning systems and surface tiltmeters are often used to measure the characteristics of these surface heaves and to derive valuable information regarding reservoir deformation and flow characteristics. In this study, Tikhonov regularization techniques were adopted to solve the ill-posed inversion problem commonly found in standard inversion techniques such as Gaussian elimination and least squares methods. Reservoir permeability was then estimated by inverting the volumetric strain distribution. Results of the newly developed numerical tool were compared with results from fully-coupled finite element simulation of fluid injection problems. The reservoir volumetric strain distribution was successfully estimated along with an approximate value for reservoir permeability.

  16. Volumetric Light-field Encryption at the Microscopic Scale

    Science.gov (United States)

    Li, Haoyu; Guo, Changliang; Muniraj, Inbarasan; Schroeder, Bryce C.; Sheridan, John T.; Jia, Shu

    2017-01-01

    We report a light-field based method that allows the optical encryption of three-dimensional (3D) volumetric information at the microscopic scale in a single 2D light-field image. The system consists of a microlens array and an array of random phase/amplitude masks. The method utilizes a wave optics model to account for the dominant diffraction effect at this new scale, and the system point-spread function (PSF) serves as the key for encryption and decryption. We successfully developed and demonstrated a deconvolution algorithm to retrieve both spatially multiplexed discrete data and continuous volumetric data from 2D light-field images. Showing that the method is practical for data transmission and storage, we obtained a faithful reconstruction of the 3D volumetric information from a digital copy of the encrypted light-field image. The method represents a new level of optical encryption, paving the way for broad industrial and biomedical applications in processing and securing 3D data at the microscopic scale.

  17. Volumetric Light-field Encryption at the Microscopic Scale

    Science.gov (United States)

    Li, Haoyu; Guo, Changliang; Muniraj, Inbarasan; Schroeder, Bryce C.; Sheridan, John T.; Jia, Shu

    2017-01-01

    We report a light-field based method that allows the optical encryption of three-dimensional (3D) volumetric information at the microscopic scale in a single 2D light-field image. The system consists of a microlens array and an array of random phase/amplitude masks. The method utilizes a wave optics model to account for the dominant diffraction effect at this new scale, and the system point-spread function (PSF) serves as the key for encryption and decryption. We successfully developed and demonstrated a deconvolution algorithm to retrieve both spatially multiplexed discrete data and continuous volumetric data from 2D light-field images. Showing that the method is practical for data transmission and storage, we obtained a faithful reconstruction of the 3D volumetric information from a digital copy of the encrypted light-field image. The method represents a new level of optical encryption, paving the way for broad industrial and biomedical applications in processing and securing 3D data at the microscopic scale. PMID:28059149

  18. Volumetric Light-field Encryption at the Microscopic Scale

    CERN Document Server

    Li, Haoyu; Muniraj, Inbarasan; Schroeder, Bryce C; Sheridan, John T; Jia, Shu

    2016-01-01

    We report a light-field based method that allows the optical encryption of three-dimensional (3D) volumetric information at the microscopic scale in a single 2D light-field image. The system consists of a microlens array and an array of random phase/amplitude masks. The method utilizes a wave optics model to account for the dominant diffraction effect at this new scale, and the system point-spread function (PSF) serves as the key for encryption and decryption. We successfully developed and demonstrated a deconvolution algorithm to retrieve spatially multiplexed discrete and continuous volumetric data from 2D light-field images. Showing that the method is practical for data transmission and storage, we obtained a faithful reconstruction of the 3D volumetric information from a digital copy of the encrypted light-field image. The method represents a new level of optical encryption, paving the way for broad industrial and biomedical applications in processing and securing 3D data at the microscopic scale.

  19. Volumetric Light-field Encryption at the Microscopic Scale.

    Science.gov (United States)

    Li, Haoyu; Guo, Changliang; Muniraj, Inbarasan; Schroeder, Bryce C; Sheridan, John T; Jia, Shu

    2017-01-06

    We report a light-field based method that allows the optical encryption of three-dimensional (3D) volumetric information at the microscopic scale in a single 2D light-field image. The system consists of a microlens array and an array of random phase/amplitude masks. The method utilizes a wave optics model to account for the dominant diffraction effect at this new scale, and the system point-spread function (PSF) serves as the key for encryption and decryption. We successfully developed and demonstrated a deconvolution algorithm to retrieve both spatially multiplexed discrete data and continuous volumetric data from 2D light-field images. Showing that the method is practical for data transmission and storage, we obtained a faithful reconstruction of the 3D volumetric information from a digital copy of the encrypted light-field image. The method represents a new level of optical encryption, paving the way for broad industrial and biomedical applications in processing and securing 3D data at the microscopic scale.

  20. Optical imaging. Expansion microscopy.

    Science.gov (United States)

    Chen, Fei; Tillberg, Paul W; Boyden, Edward S

    2015-01-30

    In optical microscopy, fine structural details are resolved by using refraction to magnify images of a specimen. We discovered that by synthesizing a swellable polymer network within a specimen, it can be physically expanded, resulting in physical magnification. By covalently anchoring specific labels located within the specimen directly to the polymer network, labels spaced closer than the optical diffraction limit can be isotropically separated and optically resolved, a process we call expansion microscopy (ExM). Thus, this process can be used to perform scalable superresolution microscopy with diffraction-limited microscopes. We demonstrate ExM with apparent ~70-nanometer lateral resolution in both cultured cells and brain tissue, performing three-color superresolution imaging of ~10(7) cubic micrometers of the mouse hippocampus with a conventional confocal microscope.

  1. Thermophysical Properties of Matter - the TPRC Data Series. Volume 13. Thermal Expansion - Nonmetallic Solids

    Science.gov (United States)

    1977-01-01

    Amer. Dental Assoc., 20, 108-19, 1933. 267 52429 Nielsen, T. H. and Leipold, M. H., "Thermal Expansion of Yttria-Stpbilized Zirconia , "J. Amer. Ceram...isotropic the coefficient of thermal Symmetres expansion is equal to three times the coefficient of linear thermal expansion; i.e., Cubic at a, a1 0 0 0...can Where sj (j = 4, 5, 6) = 0, as in cubic , hexagonal, happen in open-structure crystals, such as silicon orthorhombic, and some tetragonal crystals, a

  2. Modeling laser beam diffraction and propagation by the mode-expansion method.

    Science.gov (United States)

    Snyder, James J

    2007-08-01

    In the mode-expansion method for modeling propagation of a diffracted beam, the beam at the aperture can be expanded as a weighted set of orthogonal modes. The parameters of the expansion modes are chosen to maximize the weighting coefficient of the lowest-order mode. As the beam propagates, its field distribution can be reconstructed from the set of weighting coefficients and the Gouy phase of the lowest-order mode. We have developed a simple procedure to implement the mode-expansion method for propagation through an arbitrary ABCD matrix, and we have demonstrated that it is accurate in comparison with direct calculations of diffraction integrals and much faster.

  3. Thermal expansion behaviour of barium and strontium zirconium phosphates

    Indian Academy of Sciences (India)

    P Srikari Tantri; K Geetha; A M Umarji; Sheela K Ramasesha

    2000-12-01

    Ba1.5–SrZr4P5SiO24 compounds with = 0, 0.25, 0.5, 0.75, 1.0, 1.25 and 1.5, belonging to the low thermal expansion NZP family were synthesized by the solid state reaction method. The XRD pattern could be completely indexed with respect to R$\\bar{3}$ space group indicating the ordering of vacancy at the divalent cation octahedral sites. The microstructure and bulk thermal expansion coefficient from room temperature to 800°C of the sintered samples have been studied. All the samples show very low coefficient of thermal expansion (CTE), with = 0 samples showing negative expansion. A small substitution of strontium in the pure barium compound changes the sign of CTE. Similarly, = 1.5 sample (pure strontium) shows a positive CTE and a small substitution of barium changes its sign. = 1.0 and 1.25 samples have almost constant CTE over the entire temperature range. The low thermal expansion of these samples can be attributed to the ordering of the ions in the crystal structure of these materials.

  4. Ab-initio study of thermal expansion in pure graphene

    Energy Technology Data Exchange (ETDEWEB)

    Mann, Sarita; Kumar, Ranjan; Jindal, V. K., E-mail: jindal@pu.ac.in [Department of Physics, Panjab University, Chandigarh-160014 (India); Rani, Pooja [D.A.V. College, Sec-10, Chandigarh-160010 (India)

    2016-05-23

    Graphene is a zero band gap semiconductor with exceptionally high thermal conductivity. The electronic properties having been studied, therole of phonon in contributing to thermal expansion, thermal conductivity and other thermodynamic properties, is required to be investigated. This paper focuses more on thermal expansion. Some others results like phonon dispersion, Grüneisenparameters and bulk modulus,which are essential to estimation of thermal expansion, are also presented. The dynamical matrix was calculated using VASP code using both DFT and DFPT and the phonon frequencies were calculated using phonopy code under harmonic approximation. The linear thermal expansion coefficient of graphene is found to be strongly dependent on temperature but remains negative upto 470 K and positive thereafter, with a room temperature value of −1.44×10{sup −6}. The negative expansion coefficient is very interesting and is found to be in conformity with experimental as well as with recent theoretical estimates. There is only qualitative agreement of our results with experimental data and motivates further investigation, primarily on the high negative values of Grüneisen parameters.

  5. Ab-initio study of thermal expansion in pure graphene

    Science.gov (United States)

    Mann, Sarita; Rani, Pooja; Kumar, Ranjan; Jindal, V. K.

    2016-05-01

    Graphene is a zero band gap semiconductor with exceptionally high thermal conductivity. The electronic properties having been studied, therole of phonon in contributing to thermal expansion, thermal conductivity and other thermodynamic properties, is required to be investigated. This paper focuses more on thermal expansion. Some others results like phonon dispersion, Grüneisenparameters and bulk modulus,which are essential to estimation of thermal expansion, are also presented. The dynamical matrix was calculated using VASP code using both DFT and DFPTand the phonon frequencies were calculated using phonopy code under harmonic approximation. The linear thermal expansion coefficient of graphene is found to be strongly dependent on temperature but remains negative upto 470 K and positive thereafter, with a room temperature value of -1.44×10-6. The negative expansion coefficient is very interesting and is found to be in conformity with experimental as well as with recent theoretical estimates. There is only qualitative agreement of our results with experimental data and motivates further investigation, primarily on the high negative values of Grüneisen parameters.

  6. Performance Analysis of Electronic Expansion Valve in 1 TR Window Air Conditioner using Various Refrigerants

    Directory of Open Access Journals (Sweden)

    CHENNUCHETTY CHINNARAJ,

    2010-09-01

    Full Text Available A window air conditioner of 3.5 K.W capacity fitted with expansion devices such as capillary tube, thermostatic expansion valve and Electronic expansion valve was tested for its coefficient of performance, power required and refrigeration effect with respect to the refrigerants R22 and R407C under different operating conditions .Initially evaporator temperature was maintained at 279 K and condenser temperature was varied and then the test was conducted again in the same window air conditioner with electronic expansion valve alone as expansion device and by varying the refrigerant super heat temperature at inlet to the compressor from 273K to 293K for the refrigerants R 22, R 407C and R 290 The performance of electronic expansion valve with eco friendly refrigerants shows a positive effect and enable the industry to favorably displace the R22 and other types of expansion devices.

  7. Hydrodynamic transport coefficients for the non-conformal quark-gluon plasma from holography

    CERN Document Server

    Finazzo, Stefano I; Marrochio, Hugo; Noronha, Jorge

    2014-01-01

    In this paper we obtain holographic formulas for the transport coefficients $\\kappa$ and $\\tau_\\pi$ present in the second-order derivative expansion of relativistic hydrodynamics in curved spacetime associated with a non-conformal strongly coupled plasma described holographically by an Einstein+Scalar action in the bulk. We compute these coefficients as functions of the temperature in a bottom-up non-conformal model that is tuned to reproduce lattice QCD thermodynamics at zero baryon chemical potential. We directly compute, besides the speed of sound, 6 other transport coefficients that appear at second-order in the derivative expansion. We also give an estimate for the temperature dependence of 11 other transport coefficients taking into account the simplest contribution from non-conformal effects that appear near the QCD crossover phase transition. Using these results, we construct an Israel-Stewart-like theory in flat spacetime containing 13 of these 17 transport coefficients that should be suitable for ph...

  8. DISCONTINUOUS FLOW OF TURBID DENSITY CURRENTS I. CHANNEL EXPANSION AND CONTRACTION

    Institute of Scientific and Technical Information of China (English)

    Jiahua FAN

    2005-01-01

    Laboratory experiments on turbid density currents were conducted to observe the flow features of these currents with abrupt contracted and expanded reaches. Experimental data were used to determine water entrainment coefficients for both channel expansion and contraction. Expressions for turbid density currents with water entrainment coefficients in abrupt contracted and expanded reaches were derived,and compared with experimental data.

  9. Silicon carbide-free graphene growth on silicon for lithium-ion battery with high volumetric energy density

    Science.gov (United States)

    Son, In Hyuk; Hwan Park, Jong; Kwon, Soonchul; Park, Seongyong; Rümmeli, Mark H.; Bachmatiuk, Alicja; Song, Hyun Jae; Ku, Junhwan; Choi, Jang Wook; Choi, Jae-man; Doo, Seok-Gwang; Chang, Hyuk

    2015-01-01

    Silicon is receiving discernable attention as an active material for next generation lithium-ion battery anodes because of its unparalleled gravimetric capacity. However, the large volume change of silicon over charge–discharge cycles weakens its competitiveness in the volumetric energy density and cycle life. Here we report direct graphene growth over silicon nanoparticles without silicon carbide formation. The graphene layers anchored onto the silicon surface accommodate the volume expansion of silicon via a sliding process between adjacent graphene layers. When paired with a commercial lithium cobalt oxide cathode, the silicon carbide-free graphene coating allows the full cell to reach volumetric energy densities of 972 and 700 Wh l−1 at first and 200th cycle, respectively, 1.8 and 1.5 times higher than those of current commercial lithium-ion batteries. This observation suggests that two-dimensional layered structure of graphene and its silicon carbide-free integration with silicon can serve as a prototype in advancing silicon anodes to commercially viable technology. PMID:26109057

  10. Silicon carbide-free graphene growth on silicon for lithium-ion battery with high volumetric energy density.

    Science.gov (United States)

    Son, In Hyuk; Hwan Park, Jong; Kwon, Soonchul; Park, Seongyong; Rümmeli, Mark H; Bachmatiuk, Alicja; Song, Hyun Jae; Ku, Junhwan; Choi, Jang Wook; Choi, Jae-Man; Doo, Seok-Gwang; Chang, Hyuk

    2015-06-25

    Silicon is receiving discernable attention as an active material for next generation lithium-ion battery anodes because of its unparalleled gravimetric capacity. However, the large volume change of silicon over charge-discharge cycles weakens its competitiveness in the volumetric energy density and cycle life. Here we report direct graphene growth over silicon nanoparticles without silicon carbide formation. The graphene layers anchored onto the silicon surface accommodate the volume expansion of silicon via a sliding process between adjacent graphene layers. When paired with a commercial lithium cobalt oxide cathode, the silicon carbide-free graphene coating allows the full cell to reach volumetric energy densities of 972 and 700 Wh l(-1) at first and 200th cycle, respectively, 1.8 and 1.5 times higher than those of current commercial lithium-ion batteries. This observation suggests that two-dimensional layered structure of graphene and its silicon carbide-free integration with silicon can serve as a prototype in advancing silicon anodes to commercially viable technology.

  11. Burial Ground Expansion Hydrogeologic Characterization

    Energy Technology Data Exchange (ETDEWEB)

    Gaughan , T.F.

    1999-02-26

    Sirrine Environmental Consultants provided technical oversight of the installation of eighteen groundwater monitoring wells and six exploratory borings around the location of the Burial Ground Expansion.

  12. White matter development in early puberty: a longitudinal volumetric and diffusion tensor imaging twin study.

    Science.gov (United States)

    Brouwer, Rachel M; Mandl, René C W; Schnack, Hugo G; van Soelen, Inge L C; van Baal, G Caroline; Peper, Jiska S; Kahn, René S; Boomsma, Dorret I; Hulshoff Pol, H E

    2012-01-01

    White matter microstructure and volume show synchronous developmental patterns in children. White matter volume increases considerably during development. Fractional anisotropy, a measure for white matter microstructural directionality, also increases with age. Development of white matter volume and development of white matter microstructure seem to go hand in hand. The extent to which the same or different genetic and/or environmental factors drive these two aspects of white matter maturation is currently unknown. We mapped changes in white matter volume, surface area and diffusion parameters in mono- and dizygotic twins who were scanned at age 9 (203 individuals) and again at age 12 (126 individuals). Over the three-year interval, white matter volume (+6.0%) and surface area (+1.7%) increased, fiber bundles expanded (most pronounced in the left arcuate fasciculus and splenium), and fractional anisotropy increased (+3.0%). Genes influenced white matter volume (heritability ~85%), surface area (~85%), and fractional anisotropy (locally 7% to 50%) at both ages. Finally, volumetric white matter growth was negatively correlated with fractional anisotropy increase (r = -0.62) and this relationship was driven by environmental factors. In children who showed the most pronounced white matter growth, fractional anisotropy increased the least and vice-versa. Thus, white matter development in childhood may reflect a process of both expansion and fiber optimization.

  13. White matter development in early puberty: a longitudinal volumetric and diffusion tensor imaging twin study.

    Directory of Open Access Journals (Sweden)

    Rachel M Brouwer

    Full Text Available White matter microstructure and volume show synchronous developmental patterns in children. White matter volume increases considerably during development. Fractional anisotropy, a measure for white matter microstructural directionality, also increases with age. Development of white matter volume and development of white matter microstructure seem to go hand in hand. The extent to which the same or different genetic and/or environmental factors drive these two aspects of white matter maturation is currently unknown. We mapped changes in white matter volume, surface area and diffusion parameters in mono- and dizygotic twins who were scanned at age 9 (203 individuals and again at age 12 (126 individuals. Over the three-year interval, white matter volume (+6.0% and surface area (+1.7% increased, fiber bundles expanded (most pronounced in the left arcuate fasciculus and splenium, and fractional anisotropy increased (+3.0%. Genes influenced white matter volume (heritability ~85%, surface area (~85%, and fractional anisotropy (locally 7% to 50% at both ages. Finally, volumetric white matter growth was negatively correlated with fractional anisotropy increase (r = -0.62 and this relationship was driven by environmental factors. In children who showed the most pronounced white matter growth, fractional anisotropy increased the least and vice-versa. Thus, white matter development in childhood may reflect a process of both expansion and fiber optimization.

  14. Adaptive Cell Segmentation and Tracking for Volumetric Confocal Microscopy Images of a Developing Plant Meristem

    Institute of Scientific and Technical Information of China (English)

    Min Liu; Anirban Chakraborty; Damanpreet Singh; Ram Kishor Yadav; Gopi Meenakshisundaram; G. Venugopala Reddy; Amit Roy-Chowdhury

    2011-01-01

    Automated segmentation and tracking of cells in actively developing tissues can provide high-throughput and quantitative spatiotemporal measurements of a range of cell behaviors; cell expansion and cell-division kinetics leading to a better understanding of the underlying dynamics of morphogenesis.Here,we have studied the problem of constructing cell lineages in time-lapse volumetric image stacks obtained using Confocal Laser Scanning Microscopy (CLSM).The novel contribution of the work lies in its ability to segment and track cells in densely packed tissue,the shoot apical meristem (SAM),through the use of a close-loop,adaptive segmentation,and tracking approach.The tracking output acts as an indicator of the quality of segmentation and,in turn,the segmentation can be improved to obtain better tracking results.We construct an optimization function that minimizes the segmentation error,which is,in turn,estimated from the tracking results.This adaptive approach significantly improves both tracking and segmentation when compared to an open loop framework in which segmentation and tracking modules operate separately.

  15. Broadband computation of the scattering coefficients of infinite arbitrary cylinders.

    Science.gov (United States)

    Blanchard, Cédric; Guizal, Brahim; Felbacq, Didier

    2012-07-01

    We employ a time-domain method to compute the near field on a contour enclosing infinitely long cylinders of arbitrary cross section and constitution. We therefore recover the cylindrical Hankel coefficients of the expansion of the field outside the circumscribed circle of the structure. The recovered coefficients enable the wideband analysis of complex systems, e.g., the determination of the radar cross section becomes straightforward. The prescription for constructing such a numerical tool is provided in great detail. The method is validated by computing the scattering coefficients for a homogeneous circular cylinder illuminated by a plane wave, a problem for which an analytical solution exists. Finally, some radiation properties of an optical antenna are examined by employing the proposed technique.

  16. The Kauffman Constraint Coefficients Kw

    CERN Document Server

    Griggs, Kenneth A

    2011-01-01

    The Kauffman Constraint Coefficients Kw and their corresponding Elementals Ew are presented as solutions to the construction of the (beta)-derivative of Kauffman's Theta-function. Additionally, a new recursion relation is provided to construct the (beta)-derivative of Theta that requires only operational substitutions and summations; this algorithmically simplifies Kauffman's original technique. To demonstrate Kw, we generate the 30 Kw Coefficients from the corresponding Elementals Ew for the (9)-derivative of Theta and find that our results are in complete agreement with Kauffman's Mathematica\\texttrademark solutions. We further present a calculation of two coefficients for the (12)-derivative of Theta and invite readers to use Mathematica\\texttrademark or any other means to calculate and verify our results. Finally, we present a challenging calculation for a coefficient of the (40)-derivative of Theta; owing to the vast numbers of permutations involved, a Mathematica\\texttrademark approach may require subst...

  17. Kappa Coefficients for Circular Classifications

    NARCIS (Netherlands)

    Warrens, Matthijs J.; Pratiwi, Bunga C.

    2016-01-01

    Circular classifications are classification scales with categories that exhibit a certain periodicity. Since linear scales have endpoints, the standard weighted kappas used for linear scales are not appropriate for analyzing agreement between two circular classifications. A family of kappa coefficie

  18. Thermal expansion of d10 dicyanometallate-based coordination polymers

    OpenAIRE

    Korcok, Jasmine Lynn

    2010-01-01

    The thermal expansion of several new d10, dicyanometallate-based coordination polymers was examined by powder and single-crystal X-ray diffraction. In isostructural KNi[Au(CN)2]3, KCd[M(CN)2]3, and In[M(CN)2]3 (M=Ag(I), Au(I)), extremely large positive and negative thermal expansion (PTE/NTE) coefficients were discovered. Weaker metallophilic interactions promote larger PTE and NTE. Similarly, the M[Au(CN)2]2 series (M=Mn, Fe, Co, Zn, Hg) showed sizeable PTE and NTE effects. HgCN(NO3) exhibit...

  19. Stress Response of Offshore Structures by Equivalent Polynomial Expansion Techniques

    DEFF Research Database (Denmark)

    Sigurdsson, Gudfinnur; Nielsen, Søren R.K.

    This paper concerns an investigation of the effects of nonlinearity of drag loading on offshore structures excited by 2D wave fields, where the nonlinear term in the Morison equation is replaced by an equivalent cubic expansion. The equivalent cubic expansion coefficients for the equivalent drag...... model are obtained using the least mean square procedure. Numerical results are given. The displacement response and stress response processes obtained using the above loading model are compared with simulation results and those obtained from equivalent linearization of the drag term....

  20. Thermal Expansion Behavior of Hot-Pressed Engineered Matrices

    Science.gov (United States)

    Raj, S. V.

    2016-01-01

    Advanced engineered matrix composites (EMCs) require that the coefficient of thermal expansion (CTE) of the engineered matrix (EM) matches those of the fiber reinforcements as closely as possible in order to reduce thermal compatibility strains during heating and cooling of the composites. The present paper proposes a general concept for designing suitable matrices for long fiber reinforced composites using a rule of mixtures (ROM) approach to minimize the global differences in the thermal expansion mismatches between the fibers and the engineered matrix. Proof-of-concept studies were conducted to demonstrate the validity of the concept.

  1. Properties of Traffic Risk Coefficient

    Institute of Scientific and Technical Information of China (English)

    TANG Tie-Qiao; HUANG Hai-Jun; SHANG Hua-Yan; XUE Yu

    2009-01-01

    We use the model with the consideration of the traffic interruption probability (Physica A 387(2008)6845) to study the relationship between the traffic risk coefficient and the traffic interruption probability.The analytical and numerical results show that the traffic interruption probability will reduce the traffic risk coefficient and that the reduction is related to the density, which shows that this model can improve traffic security.

  2. Wrong Signs in Regression Coefficients

    Science.gov (United States)

    McGee, Holly

    1999-01-01

    When using parametric cost estimation, it is important to note the possibility of the regression coefficients having the wrong sign. A wrong sign is defined as a sign on the regression coefficient opposite to the researcher's intuition and experience. Some possible causes for the wrong sign discussed in this paper are a small range of x's, leverage points, missing variables, multicollinearity, and computational error. Additionally, techniques for determining the cause of the wrong sign are given.

  3. The gas-liquid mass transfer coefficient (k(L)a) in the gas-liquid Multi-stage Agitated Contactor (MAC)

    NARCIS (Netherlands)

    Breman, B.B; Beenackers, A.A C M; Bouma, M.J; VanderWerf, M.H.

    1996-01-01

    Data on the volumetric liquid-side gas-liquid mass transfer coefficient, k(L)a, in a Multi-stage Agitated Contractor (MAC) are reported for three gas-liquid systems (air-water, helium-n-octane, and air-Monoethylene Glycol (MEG)). k(L)a (s(-1)) was determined using a dynamic method with moderately so

  4. Volumetric CT-images improve testing of radiological image interpretation skills

    Energy Technology Data Exchange (ETDEWEB)

    Ravesloot, Cécile J., E-mail: C.J.Ravesloot@umcutrecht.nl [Radiology Department at University Medical Center Utrecht, Heidelberglaan 100, 3508 GA Utrecht, Room E01.132 (Netherlands); Schaaf, Marieke F. van der, E-mail: M.F.vanderSchaaf@uu.nl [Department of Pedagogical and Educational Sciences at Utrecht University, Heidelberglaan 1, 3584 CS Utrecht (Netherlands); Schaik, Jan P.J. van, E-mail: J.P.J.vanSchaik@umcutrecht.nl [Radiology Department at University Medical Center Utrecht, Heidelberglaan 100, 3508 GA Utrecht, Room E01.132 (Netherlands); Cate, Olle Th.J. ten, E-mail: T.J.tenCate@umcutrecht.nl [Center for Research and Development of Education at University Medical Center Utrecht, Heidelberglaan 100, 3508 GA Utrecht (Netherlands); Gijp, Anouk van der, E-mail: A.vanderGijp-2@umcutrecht.nl [Radiology Department at University Medical Center Utrecht, Heidelberglaan 100, 3508 GA Utrecht, Room E01.132 (Netherlands); Mol, Christian P., E-mail: C.Mol@umcutrecht.nl [Image Sciences Institute at University Medical Center Utrecht, Heidelberglaan 100, 3508 GA Utrecht (Netherlands); Vincken, Koen L., E-mail: K.Vincken@umcutrecht.nl [Image Sciences Institute at University Medical Center Utrecht, Heidelberglaan 100, 3508 GA Utrecht (Netherlands)

    2015-05-15

    Rationale and objectives: Current radiology practice increasingly involves interpretation of volumetric data sets. In contrast, most radiology tests still contain only 2D images. We introduced a new testing tool that allows for stack viewing of volumetric images in our undergraduate radiology program. We hypothesized that tests with volumetric CT-images enhance test quality, in comparison with traditional completely 2D image-based tests, because they might better reflect required skills for clinical practice. Materials and methods: Two groups of medical students (n = 139; n = 143), trained with 2D and volumetric CT-images, took a digital radiology test in two versions (A and B), each containing both 2D and volumetric CT-image questions. In a questionnaire, they were asked to comment on the representativeness for clinical practice, difficulty and user-friendliness of the test questions and testing program. Students’ test scores and reliabilities, measured with Cronbach's alpha, of 2D and volumetric CT-image tests were compared. Results: Estimated reliabilities (Cronbach's alphas) were higher for volumetric CT-image scores (version A: .51 and version B: .54), than for 2D CT-image scores (version A: .24 and version B: .37). Participants found volumetric CT-image tests more representative of clinical practice, and considered them to be less difficult than volumetric CT-image questions. However, in one version (A), volumetric CT-image scores (M 80.9, SD 14.8) were significantly lower than 2D CT-image scores (M 88.4, SD 10.4) (p < .001). The volumetric CT-image testing program was considered user-friendly. Conclusion: This study shows that volumetric image questions can be successfully integrated in students’ radiology testing. Results suggests that the inclusion of volumetric CT-images might improve the quality of radiology tests by positively impacting perceived representativeness for clinical practice and increasing reliability of the test.

  5. Thermal Expansion Anomaly of Tb2Fe14Cr3 Compound

    Institute of Scientific and Technical Information of China (English)

    HAO Yan-Ming; HE Xiao-Hong; AN Li-Qun; Fu Bin

    2008-01-01

    We investigate the thermal expansion property of the Tb2Fe14Cr3 compound by means of x-ray diffraction.The result shows that the Tb2Fe14Cr3 compound has a hexagonal Th2Ni17-type structure.Negative thermal expansion is found in the Tb2Fe14Cr3 compound from 296 to 493K by x-ray dilatometry.The coefficient of the average thermal expansion is (a)=-2.82×10-5 K-1.In the temperature range 493-692K,the coefficient of the average thermal expansion is (a)=1.59×10-5 K-1.The physical mechanism of thermal expansion anomaly of the Tb2Fe14Cr3 compound is discussed according to the temperature dependence of magnetization measured by a superconducting quantum interference device.

  6. Orthogonal Query Expansion

    CERN Document Server

    Ackerman, Margareta; Lopez-Ortiz, Alejandro

    2011-01-01

    Over the last fifteen years, web searching has seen tremendous improvements. Starting from a nearly random collection of matching pages in 1995, today, search engines tend to satisfy the user's informational need on well-formulated queries. One of the main remaining challenges is to satisfy the users' needs when they provide a poorly formulated query. When the pages matching the user's original keywords are judged to be unsatisfactory, query expansion techniques are used to alter the result set. These techniques find keywords that are similar to the keywords given by the user, which are then appended to the original query leading to a perturbation of the result set. However, when the original query is sufficiently ill-posed, the user's informational need is best met using entirely different keywords, and a small perturbation of the original result set is bound to fail. We propose a novel approach that is not based on the keywords of the original query. We intentionally seek out orthogonal queries, which are r...

  7. Lattice harmonics expansion revisited

    Science.gov (United States)

    Kontrym-Sznajd, G.; Holas, A.

    2017-04-01

    The main subject of the work is to provide the most effective way of determining the expansion of some quantities into orthogonal polynomials, when these quantities are known only along some limited number of sampling directions. By comparing the commonly used Houston method with the method based on the orthogonality relation, some relationships, which define the applicability and correctness of these methods, are demonstrated. They are verified for various sets of sampling directions applicable for expanding quantities having the full symmetry of the Brillouin zone of cubic and non-cubic lattices. All results clearly show that the Houston method is always better than the orthogonality-relation one. For the cubic symmetry we present a few sets of special directions (SDs) showing how their construction and, next, a proper application depend on the choice of various sets of lattice harmonics. SDs are important mainly for experimentalists who want to reconstruct anisotropic quantities from their measurements, performed at a limited number of sampling directions.

  8. A semi-automated volumetric software for segmentation and perfusion parameter quantification of brain tumors using 320-row multidetector computed tomography: a validation study

    Energy Technology Data Exchange (ETDEWEB)

    Chae, Soo Young; Suh, Sangil; Ryoo, Inseon; Park, Arim; Seol, Hae Young [Korea University Guro Hospital, Department of Radiology, Seoul (Korea, Republic of); Noh, Kyoung Jin [Soonchunhyang University, Department of Electronic Engineering, Asan (Korea, Republic of); Shim, Hackjoon [Toshiba Medical Systems Korea Co., Seoul (Korea, Republic of)

    2017-05-15

    We developed a semi-automated volumetric software, NPerfusion, to segment brain tumors and quantify perfusion parameters on whole-brain CT perfusion (WBCTP) images. The purpose of this study was to assess the feasibility of the software and to validate its performance compared with manual segmentation. Twenty-nine patients with pathologically proven brain tumors who underwent preoperative WBCTP between August 2012 and February 2015 were included. Three perfusion parameters, arterial flow (AF), equivalent blood volume (EBV), and Patlak flow (PF, which is a measure of permeability of capillaries), of brain tumors were generated by a commercial software and then quantified volumetrically by NPerfusion, which also semi-automatically segmented tumor boundaries. The quantification was validated by comparison with that of manual segmentation in terms of the concordance correlation coefficient and Bland-Altman analysis. With NPerfusion, we successfully performed segmentation and quantified whole volumetric perfusion parameters of all 29 brain tumors that showed consistent perfusion trends with previous studies. The validation of the perfusion parameter quantification exhibited almost perfect agreement with manual segmentation, with Lin concordance correlation coefficients (ρ {sub c}) for AF, EBV, and PF of 0.9988, 0.9994, and 0.9976, respectively. On Bland-Altman analysis, most differences between this software and manual segmentation on the commercial software were within the limit of agreement. NPerfusion successfully performs segmentation of brain tumors and calculates perfusion parameters of brain tumors. We validated this semi-automated segmentation software by comparing it with manual segmentation. NPerfusion can be used to calculate volumetric perfusion parameters of brain tumors from WBCTP. (orig.)

  9. Modal analysis of the scattering coefficients of an open cavity in a waveguide

    CERN Document Server

    Tong, Yuhui

    2016-01-01

    The characteristics of an acoustic scatterer are often described by scattering coefficients. The understanding of the mechanisms involved in the frequency dependent features of the coefficients has been a challenge task, owing to the complicated coupling between the waves in open space and the modes inside the finite scatterer. In this paper, a frequency-dependent modal description of the scattering coefficient is utilized to study the modal properties of the scatterer. The important role that eigenmodes play in defining the features of the scattering coefficients is revealed via an expansion of the coefficients by the eigenmodes. The results show the local extrema of the scattering coefficients can be attributed to the constructive/destructive interference of resonant and non-resonant modes. In particular, an approximated equation, which is equivalent to the standard Fano formula, is obtained to describe the sharp anti-symmetric Fano characteristics of the scattering coefficients. The special cases where sca...

  10. Personalized heterogeneous deformable model for fast volumetric registration.

    Science.gov (United States)

    Si, Weixin; Liao, Xiangyun; Wang, Qiong; Heng, Pheng Ann

    2017-02-20

    Biomechanical deformable volumetric registration can help improve safety of surgical interventions by ensuring the operations are extremely precise. However, this technique has been limited by the accuracy and the computational efficiency of patient-specific modeling. This study presents a tissue-tissue coupling strategy based on penalty method to model the heterogeneous behavior of deformable body, and estimate the personalized tissue-tissue coupling parameters in a data-driven way. Moreover, considering that the computational efficiency of biomechanical model is highly dependent on the mechanical resolution, a practical coarse-to-fine scheme is proposed to increase runtime efficiency. Particularly, a detail enrichment database is established in an offline fashion to represent the mapping relationship between the deformation results of high-resolution hexahedral mesh extracted from the raw medical data and a newly constructed low-resolution hexahedral mesh. At runtime, the mechanical behavior of human organ under interactions is simulated with this low-resolution hexahedral mesh, then the microstructures are synthesized in virtue of the detail enrichment database. The proposed method is validated by volumetric registration in an abdominal phantom compression experiments. Our personalized heterogeneous deformable model can well describe the coupling effects between different tissues of the phantom. Compared with high-resolution heterogeneous deformable model, the low-resolution deformable model with our detail enrichment database can achieve 9.4× faster, and the average target registration error is 3.42 mm, which demonstrates that the proposed method shows better volumetric registration performance than state-of-the-art. Our framework can well balance the precision and efficiency, and has great potential to be adopted in the practical augmented reality image-guided robotic systems.

  11. Volumetric measurements of pulmonary nodules: variability in automated analysis tools

    Science.gov (United States)

    Juluru, Krishna; Kim, Woojin; Boonn, William; King, Tara; Siddiqui, Khan; Siegel, Eliot

    2007-03-01

    Over the past decade, several computerized tools have been developed for detection of lung nodules and for providing volumetric analysis. Incidentally detected lung nodules have traditionally been followed over time by measurements of their axial dimensions on CT scans to ensure stability or document progression. A recently published article by the Fleischner Society offers guidelines on the management of incidentally detected nodules based on size criteria. For this reason, differences in measurements obtained by automated tools from various vendors may have significant implications on management, yet the degree of variability in these measurements is not well understood. The goal of this study is to quantify the differences in nodule maximum diameter and volume among different automated analysis software. Using a dataset of lung scans obtained with both "ultra-low" and conventional doses, we identified a subset of nodules in each of five size-based categories. Using automated analysis tools provided by three different vendors, we obtained size and volumetric measurements on these nodules, and compared these data using descriptive as well as ANOVA and t-test analysis. Results showed significant differences in nodule maximum diameter measurements among the various automated lung nodule analysis tools but no significant differences in nodule volume measurements. These data suggest that when using automated commercial software, volume measurements may be a more reliable marker of tumor progression than maximum diameter. The data also suggest that volumetric nodule measurements may be relatively reproducible among various commercial workstations, in contrast to the variability documented when performing human mark-ups, as is seen in the LIDC (lung imaging database consortium) study.

  12. Volumetric hemispheric ratio as a useful tool in personality psychology.

    Science.gov (United States)

    Montag, Christian; Schoene-Bake, Jan-Christoph; Wagner, Jan; Reuter, Martin; Markett, Sebastian; Weber, Bernd; Quesada, Carlos M

    2013-02-01

    The present study investigates the link between volumetric hemispheric ratios (VHRs) and personality measures in N=267 healthy participants using Eysenck's Personality Inventory-Revised (EPQ-R) and the BIS/BAS scales. A robust association between extraversion and VHRs was observed for gray matter in males but not females. Higher gray matter volume in the left than in the right hemisphere was associated with higher extraversion in males. The results are discussed in the context of positive emotionality and laterality of the human brain.

  13. AN ATTRIBUTION OF CAVITATION RESONANCE: VOLUMETRIC OSCILLATIONS OF CLOUD

    Institute of Scientific and Technical Information of China (English)

    ZUO Zhi-gang; LI Sheng-cai; LIU Shu-hong; LI Shuang; CHEN Hui

    2009-01-01

    In order to further verify the proposed theory of cavitation resonance, as well as to proceed the investigations into microscopic level, a series of studies are being carried out on the Warwick venturi. The analysis of the oscillation characteristics of the cavitation resonance has conclusively verified the macro-mechanism proposed through previous studies on other cavitating flows by the authors. The initial observations using high-speed photographic approach have revealed a new attribution of cavitation resonance. That is, the volumetric oscillation of cavitation cloud is associated with the cavitation resonance, which is a collective behaviour of the bubbles in the cloud.

  14. Synthesis of Volumetric Ring Antenna Array for Terrestrial Coverage Pattern

    Directory of Open Access Journals (Sweden)

    Alberto Reyna

    2014-01-01

    Full Text Available This paper presents a synthesis of a volumetric ring antenna array for a terrestrial coverage pattern. This synthesis regards the spacing among the rings on the planes X-Y, the positions of the rings on the plane X-Z, and uniform and concentric excitations. The optimization is carried out by implementing the particle swarm optimization. The synthesis is compared with previous designs by resulting with proper performance of this geometry to provide an accurate coverage to be applied in satellite applications with a maximum reduction of the antenna hardware as well as the side lobe level reduction.

  15. Synthesis of Volumetric Ring Antenna Array for Terrestrial Coverage Pattern

    Science.gov (United States)

    Reyna, Alberto; Panduro, Marco A.; Del Rio Bocio, Carlos

    2014-01-01

    This paper presents a synthesis of a volumetric ring antenna array for a terrestrial coverage pattern. This synthesis regards the spacing among the rings on the planes X-Y, the positions of the rings on the plane X-Z, and uniform and concentric excitations. The optimization is carried out by implementing the particle swarm optimization. The synthesis is compared with previous designs by resulting with proper performance of this geometry to provide an accurate coverage to be applied in satellite applications with a maximum reduction of the antenna hardware as well as the side lobe level reduction. PMID:24701150

  16. Estimation of volumetric breast density for breast cancer risk prediction

    Science.gov (United States)

    Pawluczyk, Olga; Yaffe, Martin J.; Boyd, Norman F.; Jong, Roberta A.

    2000-04-01

    Mammographic density (MD) has been shown to be a strong risk predictor for breast cancer. Compared to subjective assessment by a radiologist, computer-aided analysis of digitized mammograms provides a quantitative and more reproducible method for assessing breast density. However, the current methods of estimating breast density based on the area of bright signal in a mammogram do not reflect the true, volumetric quantity of dense tissue in the breast. A computerized method to estimate the amount of radiographically dense tissue in the overall volume of the breast has been developed to provide an automatic, user-independent tool for breast cancer risk assessment. The procedure for volumetric density estimation consists of first correcting the image for inhomogeneity, then performing a volume density calculation. First, optical sensitometry is used to convert all images to the logarithm of relative exposure (LRE), in order to simplify the image correction operations. The field non-uniformity correction, which takes into account heel effect, inverse square law, path obliquity and intrinsic field and grid non- uniformity is obtained by imaging a spherical section PMMA phantom. The processed LRE image of the phantom is then used as a correction offset for actual mammograms. From information about the thickness and placement of the breast, as well as the parameters of a breast-like calibration step wedge placed in the mammogram, MD of the breast is calculated. Post processing and a simple calibration phantom enable user- independent, reliable and repeatable volumetric estimation of density in breast-equivalent phantoms. Initial results obtained on known density phantoms show the estimation to vary less than 5% in MD from the actual value. This can be compared to estimated mammographic density differences of 30% between the true and non-corrected values. Since a more simplistic breast density measurement based on the projected area has been shown to be a strong indicator

  17. Volumetric 3D Display System with Static Screen

    Science.gov (United States)

    Geng, Jason

    2011-01-01

    Current display technology has relied on flat, 2D screens that cannot truly convey the third dimension of visual information: depth. In contrast to conventional visualization that is primarily based on 2D flat screens, the volumetric 3D display possesses a true 3D display volume, and places physically each 3D voxel in displayed 3D images at the true 3D (x,y,z) spatial position. Each voxel, analogous to a pixel in a 2D image, emits light from that position to form a real 3D image in the eyes of the viewers. Such true volumetric 3D display technology provides both physiological (accommodation, convergence, binocular disparity, and motion parallax) and psychological (image size, linear perspective, shading, brightness, etc.) depth cues to human visual systems to help in the perception of 3D objects. In a volumetric 3D display, viewers can watch the displayed 3D images from a completely 360 view without using any special eyewear. The volumetric 3D display techniques may lead to a quantum leap in information display technology and can dramatically change the ways humans interact with computers, which can lead to significant improvements in the efficiency of learning and knowledge management processes. Within a block of glass, a large amount of tiny dots of voxels are created by using a recently available machining technique called laser subsurface engraving (LSE). The LSE is able to produce tiny physical crack points (as small as 0.05 mm in diameter) at any (x,y,z) location within the cube of transparent material. The crack dots, when illuminated by a light source, scatter the light around and form visible voxels within the 3D volume. The locations of these tiny voxels are strategically determined such that each can be illuminated by a light ray from a high-resolution digital mirror device (DMD) light engine. The distribution of these voxels occupies the full display volume within the static 3D glass screen. This design eliminates any moving screen seen in previous

  18. On genus expansion of superpolynomials

    CERN Document Server

    Mironov, A; Sleptsov, A; Smirnov, A

    2013-01-01

    Recently it was shown that the (Ooguri-Vafa) generating function of HOMFLY polynomials is the Hurwitz partition function, i.e. that the dependence of the HOMFLY polynomials on representation is naturally captured by symmetric group characters (cut-and-join eigenvalues). The genus expansion and expansion through Vassiliev invariants explicitly demonstrate this phenomenon. In the present letter we claim that the superpolynomials are not functions of such a type: symmetric group characters do not provide an adequate linear basis for their expansions. Deformation to superpolynomials is, however, straightforward in the multiplicative basis:the Casimir operators are beta-deformed to Hamiltonians of the Calogero-Moser-Sutherland system. Applying this trick to the genus and Vassiliev expansions, we observe that the deformation is rather straightforward only for the thin knots. Beyond this family additional algebraically independent terms appear in the Vassiliev and genus expansions. This can suggest that the superpol...

  19. Floating volumetric image formation using a dihedral corner reflector array device.

    Science.gov (United States)

    Miyazaki, Daisuke; Hirano, Noboru; Maeda, Yuki; Yamamoto, Siori; Mukai, Takaaki; Maekawa, Satoshi

    2013-01-01

    A volumetric display system using an optical imaging device consisting of numerous dihedral corner reflectors placed perpendicular to the surface of a metal plate is proposed. Image formation by the dihedral corner reflector array (DCRA) is free from distortion and focal length. In the proposed volumetric display system, a two-dimensional real image is moved by a mirror scanner to scan a three-dimensional (3D) space. Cross-sectional images of a 3D object are displayed in accordance with the position of the image plane. A volumetric image is observed as a stack of the cross-sectional images. The use of the DCRA brings compact system configuration and volumetric real image generation with very low distortion. An experimental volumetric display system including a DCRA, a galvanometer mirror, and a digital micro-mirror device was constructed to verify the proposed method. A volumetric image consisting of 1024×768×400 voxels was formed by the experimental system.

  20. Transport coefficients of heavy baryons

    Science.gov (United States)

    Tolos, Laura; Torres-Rincon, Juan M.; Das, Santosh K.

    2016-08-01

    We compute the transport coefficients (drag and momentum diffusion) of the low-lying heavy baryons Λc and Λb in a medium of light mesons formed at the later stages of high-energy heavy-ion collisions. We employ the Fokker-Planck approach to obtain the transport coefficients from unitarized baryon-meson interactions based on effective field theories that respect chiral and heavy-quark symmetries. We provide the transport coefficients as a function of temperature and heavy-baryon momentum, and analyze the applicability of certain nonrelativistic estimates. Moreover we compare our outcome for the spatial diffusion coefficient to the one coming from the solution of the Boltzmann-Uehling-Uhlenbeck transport equation, and we find a very good agreement between both calculations. The transport coefficients for Λc and Λb in a thermal bath will be used in a subsequent publication as input in a Langevin evolution code for the generation and propagation of heavy particles in heavy-ion collisions at LHC and RHIC energies.

  1. A Combined Random Forests and Active Contour Model Approach for Fully Automatic Segmentation of the Left Atrium in Volumetric MRI

    Directory of Open Access Journals (Sweden)

    Chao Ma

    2017-01-01

    Full Text Available Segmentation of the left atrium (LA from cardiac magnetic resonance imaging (MRI datasets is of great importance for image guided atrial fibrillation ablation, LA fibrosis quantification, and cardiac biophysical modelling. However, automated LA segmentation from cardiac MRI is challenging due to limited image resolution, considerable variability in anatomical structures across subjects, and dynamic motion of the heart. In this work, we propose a combined random forests (RFs and active contour model (ACM approach for fully automatic segmentation of the LA from cardiac volumetric MRI. Specifically, we employ the RFs within an autocontext scheme to effectively integrate contextual and appearance information from multisource images together for LA shape inferring. The inferred shape is then incorporated into a volume-scalable ACM for further improving the segmentation accuracy. We validated the proposed method on the cardiac volumetric MRI datasets from the STACOM 2013 and HVSMR 2016 databases and showed that it outperforms other latest automated LA segmentation methods. Validation metrics, average Dice coefficient (DC and average surface-to-surface distance (S2S, were computed as 0.9227±0.0598 and 1.14±1.205 mm, versus those of 0.6222–0.878 and 1.34–8.72 mm, obtained by other methods, respectively.

  2. A Combined Random Forests and Active Contour Model Approach for Fully Automatic Segmentation of the Left Atrium in Volumetric MRI

    Science.gov (United States)

    Luo, Gongning

    2017-01-01

    Segmentation of the left atrium (LA) from cardiac magnetic resonance imaging (MRI) datasets is of great importance for image guided atrial fibrillation ablation, LA fibrosis quantification, and cardiac biophysical modelling. However, automated LA segmentation from cardiac MRI is challenging due to limited image resolution, considerable variability in anatomical structures across subjects, and dynamic motion of the heart. In this work, we propose a combined random forests (RFs) and active contour model (ACM) approach for fully automatic segmentation of the LA from cardiac volumetric MRI. Specifically, we employ the RFs within an autocontext scheme to effectively integrate contextual and appearance information from multisource images together for LA shape inferring. The inferred shape is then incorporated into a volume-scalable ACM for further improving the segmentation accuracy. We validated the proposed method on the cardiac volumetric MRI datasets from the STACOM 2013 and HVSMR 2016 databases and showed that it outperforms other latest automated LA segmentation methods. Validation metrics, average Dice coefficient (DC) and average surface-to-surface distance (S2S), were computed as 0.9227 ± 0.0598 and 1.14 ± 1.205 mm, versus those of 0.6222–0.878 and 1.34–8.72 mm, obtained by other methods, respectively. PMID:28316992

  3. Volumetric display containing multiple two-dimensional color motion pictures

    Science.gov (United States)

    Hirayama, R.; Shiraki, A.; Nakayama, H.; Kakue, T.; Shimobaba, T.; Ito, T.

    2014-06-01

    We have developed an algorithm which can record multiple two-dimensional (2-D) gradated projection patterns in a single three-dimensional (3-D) object. Each recorded pattern has the individual projected direction and can only be seen from the direction. The proposed algorithm has two important features: the number of recorded patterns is theoretically infinite and no meaningful pattern can be seen outside of the projected directions. In this paper, we expanded the algorithm to record multiple 2-D projection patterns in color. There are two popular ways of color mixing: additive one and subtractive one. Additive color mixing used to mix light is based on RGB colors and subtractive color mixing used to mix inks is based on CMY colors. We made two coloring methods based on the additive mixing and subtractive mixing. We performed numerical simulations of the coloring methods, and confirmed their effectiveness. We also fabricated two types of volumetric display and applied the proposed algorithm to them. One is a cubic displays constructed by light-emitting diodes (LEDs) in 8×8×8 array. Lighting patterns of LEDs are controlled by a microcomputer board. The other one is made of 7×7 array of threads. Each thread is illuminated by a projector connected with PC. As a result of the implementation, we succeeded in recording multiple 2-D color motion pictures in the volumetric displays. Our algorithm can be applied to digital signage, media art and so forth.

  4. Volumetric three-dimensional display system with rasterization hardware

    Science.gov (United States)

    Favalora, Gregg E.; Dorval, Rick K.; Hall, Deirdre M.; Giovinco, Michael; Napoli, Joshua

    2001-06-01

    An 8-color multiplanar volumetric display is being developed by Actuality Systems, Inc. It will be capable of utilizing an image volume greater than 90 million voxels, which we believe is the greatest utilizable voxel set of any volumetric display constructed to date. The display is designed to be used for molecular visualization, mechanical CAD, e-commerce, entertainment, and medical imaging. As such, it contains a new graphics processing architecture, novel high-performance line- drawing algorithms, and an API similar to a current standard. Three-dimensional imagery is created by projecting a series of 2-D bitmaps ('image slices') onto a diffuse screen that rotates at 600 rpm. Persistence of vision fuses the slices into a volume-filling 3-D image. A modified three-panel Texas Instruments projector provides slices at approximately 4 kHz, resulting in 8-color 3-D imagery comprised of roughly 200 radially-disposed slices which are updated at 20 Hz. Each slice has a resolution of 768 by 768 pixels, subtending 10 inches. An unusual off-axis projection scheme incorporating tilted rotating optics is used to maintain good focus across the projection screen. The display electronics includes a custom rasterization architecture which converts the user's 3- D geometry data into image slices, as well as 6 Gbits of DDR SDRAM graphics memory.

  5. Myocardial kinematics based on tagged MRI from volumetric NURBS models

    Science.gov (United States)

    Tustison, Nicholas J.; Amini, Amir A.

    2004-04-01

    We present current research in which left ventricular deformation is estimated from tagged cardiac magnetic resonance imaging using volumetric deformable models constructed from nonuniform rational B-splines (NURBS). From a set of short and long axis images at end-diastole, the initial NURBS model is constructed by fitting two surfaces with the same parameterization to the set of epicardial and endocardial contours from which a volumetric model is created. Using normal displacements of the three sets of orthogonal tag planes as well as displacements of both tag line and contour/tag line intersection points, one can solve for the optimal homogeneous coordinates, in a least squares sense, of the control points of the NURBS model at a later time point using quadratic programming. After fitting to all time points of data, lofting the NURBS model at each time point creates a comprehensive 4-D NURBS model. From this model, we can extract 3-D myocardial displacement fields and corresponding strain maps, which are local measures of non-rigid deformation.

  6. Volumetric breast density affects performance of digital screening mammography.

    Science.gov (United States)

    Wanders, Johanna O P; Holland, Katharina; Veldhuis, Wouter B; Mann, Ritse M; Pijnappel, Ruud M; Peeters, Petra H M; van Gils, Carla H; Karssemeijer, Nico

    2017-02-01

    To determine to what extent automatically measured volumetric mammographic density influences screening performance when using digital mammography (DM). We collected a consecutive series of 111,898 DM examinations (2003-2011) from one screening unit of the Dutch biennial screening program (age 50-75 years). Volumetric mammographic density was automatically assessed using Volpara. We determined screening performance measures for four density categories comparable to the American College of Radiology (ACR) breast density categories. Of all the examinations, 21.6% were categorized as density category 1 ('almost entirely fatty') and 41.5, 28.9, and 8.0% as category 2-4 ('extremely dense'), respectively. We identified 667 screen-detected and 234 interval cancers. Interval cancer rates were 0.7, 1.9, 2.9, and 4.4‰ and false positive rates were 11.2, 15.1, 18.2, and 23.8‰ for categories 1-4, respectively (both p-trend density categories: 85.7, 77.6, 69.5, and 61.0% for categories 1-4, respectively (p-trend density, automatically measured on digital mammograms, impacts screening performance measures along the same patterns as established with ACR breast density categories. Since measuring breast density fully automatically has much higher reproducibility than visual assessment, this automatic method could help with implementing density-based supplemental screening.

  7. Volumetric verification of multiaxis machine tool using laser tracker.

    Science.gov (United States)

    Aguado, Sergio; Samper, David; Santolaria, Jorge; Aguilar, Juan José

    2014-01-01

    This paper aims to present a method of volumetric verification in machine tools with linear and rotary axes using a laser tracker. Beyond a method for a particular machine, it presents a methodology that can be used in any machine type. Along this paper, the schema and kinematic model of a machine with three axes of movement, two linear and one rotational axes, including the measurement system and the nominal rotation matrix of the rotational axis are presented. Using this, the machine tool volumetric error is obtained and nonlinear optimization techniques are employed to improve the accuracy of the machine tool. The verification provides a mathematical, not physical, compensation, in less time than other methods of verification by means of the indirect measurement of geometric errors of the machine from the linear and rotary axes. This paper presents an extensive study about the appropriateness and drawbacks of the regression function employed depending on the types of movement of the axes of any machine. In the same way, strengths and weaknesses of measurement methods and optimization techniques depending on the space available to place the measurement system are presented. These studies provide the most appropriate strategies to verify each machine tool taking into consideration its configuration and its available work space.

  8. The Volumetric Rate of Superluminous Supernovae at z~1

    CERN Document Server

    Prajs, S; Smith, M; Levan, A; Karpenka, N V; Edwards, T D P; Walker, C R; Wolf, W M; Balland, C; Carlberg, R; Howell, A; Lidman, C; Pain, R; Pritchet, C; Ruhlmann-Kleider, V

    2016-01-01

    We present a measurement of the volumetric rate of superluminous supernovae (SLSNe) at z~1, measured using archival data from the first four years of the Canada-France-Hawaii Telescope Supernova Legacy Survey (SNLS). We develop a method for the photometric classification of SLSNe to construct our sample. Our sample includes two previously spectroscopically-identified objects, and a further new candidate selected using our classification technique. We use the point-source recovery efficiencies from Perrett et.al. (2010) and a Monte Carlo approach to calculate the rate based on our SLSN sample. We find that the three identified SLSNe from SNLS give a rate of 91 (+76/-36) SNe/Yr/Gpc^3 at a volume-weighted redshift of z=1.13. This is equivalent to 2.2 (+1.8/-0.9) x10^-4 of the volumetric core collapse supernova rate at the same redshift. When combined with other rate measurements from the literature, we show that the rate of SLSNe increases with redshift in a manner consistent with that of the cosmic star formati...

  9. Global Monte Carlo Simulation with High Order Polynomial Expansions

    Energy Technology Data Exchange (ETDEWEB)

    William R. Martin; James Paul Holloway; Kaushik Banerjee; Jesse Cheatham; Jeremy Conlin

    2007-12-13

    The functional expansion technique (FET) was recently developed for Monte Carlo simulation. The basic idea of the FET is to expand a Monte Carlo tally in terms of a high order expansion, the coefficients of which can be estimated via the usual random walk process in a conventional Monte Carlo code. If the expansion basis is chosen carefully, the lowest order coefficient is simply the conventional histogram tally, corresponding to a flat mode. This research project studied the applicability of using the FET to estimate the fission source, from which fission sites can be sampled for the next generation. The idea is that individual fission sites contribute to expansion modes that may span the geometry being considered, possibly increasing the communication across a loosely coupled system and thereby improving convergence over the conventional fission bank approach used in most production Monte Carlo codes. The project examined a number of basis functions, including global Legendre polynomials as well as “local” piecewise polynomials such as finite element hat functions and higher order versions. The global FET showed an improvement in convergence over the conventional fission bank approach. The local FET methods showed some advantages versus global polynomials in handling geometries with discontinuous material properties. The conventional finite element hat functions had the disadvantage that the expansion coefficients could not be estimated directly but had to be obtained by solving a linear system whose matrix elements were estimated. An alternative fission matrix-based response matrix algorithm was formulated. Studies were made of two alternative applications of the FET, one based on the kernel density estimator and one based on Arnoldi’s method of minimized iterations. Preliminary results for both methods indicate improvements in fission source convergence. These developments indicate that the FET has promise for speeding up Monte Carlo fission source

  10. Harmonic functions with varying coefficients

    Directory of Open Access Journals (Sweden)

    Jacek Dziok

    2016-05-01

    Full Text Available Abstract Complex-valued harmonic functions that are univalent and sense preserving in the open unit disk can be written in the form f = h + g ‾ $f=h+\\overline{g}$ , where h and g are analytic. In this paper we investigate some classes of univalent harmonic functions with varying coefficients related to Janowski functions. By using the extreme points theory we obtain necessary and sufficient convolution conditions, coefficients estimates, distortion theorems, and integral mean inequalities for these classes of functions. The radii of starlikeness and convexity for these classes are also determined.

  11. Surgical Splint Design Influences Transverse Expansion in Segmental Maxillary Osteotomies

    DEFF Research Database (Denmark)

    Stokbro, Kasper; Aagaard, Esben; Torkov, Peter

    2017-01-01

    splint designs on achieving the planned transverse expansion in bimaxillary surgery with segmental maxillary procedures. Materials and Methods: Forty-two participants were included in a retrospective observational study. All participants had completed virtually planned bimaxillary surgery with 3-piece....... To test measurement reliability, all measurements were performed twice by the same observer. The primary predictor variable was the planned expansion according to the virtual surgical plan. The primary covariate with influence on the obtained expansion was the surgical splint design. Other covariates...... of interest included patient age, patient gender, and surgeon. Descriptive and bivariate statistics were performed using Student t tests and linear regression analysis. Results: Measurements showed high reliability, with an intraclass correlation coefficient of 0.99 and Bland-Altman plots without systematic...

  12. Thin films with ultra-low thermal expansion.

    Science.gov (United States)

    Yamamoto, Namiko; Gdoutos, Eleftherios; Toda, Risaku; White, Victor; Manohara, Harish; Daraio, Chiara

    2014-05-21

    Ultra-low coefficient of thermal expansion (CTE) is an elusive property, and narrow temperature ranges of operation and poor mechanical properties limit the use of conventional materials with low CTE. We structured a periodic micro-array of bi-metallic cells to demonstrate ultra-low effective CTE with a wide temperature range. These engineered tunable CTE thin film can be applied to minimize thermal fatigue and failure of optics, semiconductors, biomedical sensors, and solar energy applications.

  13. Effect of anatomical backgrounds on detectability in volumetric cone beam CT images

    Science.gov (United States)

    Han, Minah; Park, Subok; Baek, Jongduk

    2016-03-01

    As anatomical noise is often a dominating factor affecting signal detection in medical imaging, we investigate the effects of anatomical backgrounds on signal detection in volumetric cone beam CT images. Signal detection performances are compared between transverse and longitudinal planes with either uniform or anatomical backgrounds. Sphere objects with diameters of 1mm, 5mm, 8mm, and 11mm are used as the signals. Three-dimensional (3D) anatomical backgrounds are generated using an anatomical noise power spectrum, 1/fβ, with β=3, equivalent to mammographic background [1]. The mean voxel value of the 3D anatomical backgrounds is used as an attenuation coefficient of the uniform background. Noisy projection data are acquired by the forward projection of the uniform and anatomical 3D backgrounds with/without sphere lesions and by the addition of quantum noise. Then, images are reconstructed by an FDK algorithm [2]. For each signal size, signal detection performances in transverse and longitudinal planes are measured by calculating the task SNR of a channelized Hotelling observer with Laguerre-Gauss channels. In the uniform background case, transverse planes yield higher task SNR values for all sphere diameters but 1mm. In the anatomical background case, longitudinal planes yield higher task SNR values for all signal diameters. The results indicate that it is beneficial to use longitudinal planes to detect spherical signals in anatomical backgrounds.

  14. Tensor integrand reduction via Laurent expansion

    CERN Document Server

    Hirschi, Valentin

    2016-01-01

    We introduce a new method for the application of one-loop integrand reduction via the Laurent expansion algorithm, as implemented in the public C++ library Ninja. We show how the coefficients of the Laurent expansion can be computed by suitable contractions of the loop numerator tensor with cut-dependent projectors, making it possible to interface Ninja to any one-loop matrix element generator that can provide the components of this tensor. We implemented this technique in the Ninja library and interfaced it to MadLoop, which is part of the public MadGraph5_aMC@NLO framework. We performed a detailed performance study, comparing against other public reduction tools, namely CutTools, Samurai, IREGI, PJFry++ and Golem. We find that Ninja outperforms traditional integrand reduction in both speed and numerical stability, the latter being on par with that of the tensor integral reduction tool Golem which is however more limited and slower than Ninja. We considered many benchmark multi-scale processes of increasing ...

  15. Thermal Expansion of Polyurethane Foam

    Science.gov (United States)

    Lerch, Bradley A.; Sullivan, Roy M.

    2006-01-01

    Closed cell foams are often used for thermal insulation. In the case of the Space Shuttle, the External Tank uses several thermal protection systems to maintain the temperature of the cryogenic fuels. A few of these systems are polyurethane, closed cell foams. In an attempt to better understand the foam behavior on the tank, we are in the process of developing and improving thermal-mechanical models for the foams. These models will start at the microstructural level and progress to the overall structural behavior of the foams on the tank. One of the key properties for model characterization and verification is thermal expansion. Since the foam is not a material, but a structure, the modeling of the expansion is complex. It is also exacerbated by the anisoptropy of the material. During the spraying and foaming process, the cells become elongated in the rise direction and this imparts different properties in the rise direction than in the transverse directions. Our approach is to treat the foam as a two part structure consisting of the polymeric cell structure and the gas inside the cells. The polymeric skeleton has a thermal expansion of its own which is derived from the basic polymer chemistry. However, a major contributor to the thermal expansion is the volume change associated with the gas inside of the closed cells. As this gas expands it exerts pressure on the cell walls and changes the shape and size of the cells. The amount that this occurs depends on the elastic and viscoplastic properties of the polymer skeleton. The more compliant the polymeric skeleton, the more influence the gas pressure has on the expansion. An additional influence on the expansion process is that the polymeric skeleton begins to breakdown at elevated temperatures and releases additional gas species into the cell interiors, adding to the gas pressure. The fact that this is such a complex process makes thermal expansion ideal for testing the models. This report focuses on the thermal

  16. When epsilon-expansion of hypergeometric functions is expressible in terms of multiple polylogarithms: the two-variables examples

    CERN Document Server

    Bytev, Vladimir V; Kniehl, Bernd A

    2012-01-01

    In this talk, we discuss the algorithm for the construction of analytical coefficients of higher order epsilon expansion of some Horn type hypergeometric functions of two variables around rational values of parameters.

  17. New Exact Solutions for the Generalized (2+1)-dimensional Nonlinear Schr(o)dinger Equation with Variable Coefficients

    Institute of Scientific and Technical Information of China (English)

    JIANG Zhi-ping

    2012-01-01

    With the help of the variable-coefficient generalized projected Ricatti equation expansion method,we present exact solutions for the generalized (2+1)-dimensional nonlinear Schr(o)dinger equation with variable coefficients.These solutions include solitary wave solutions,soliton-like solutions and trigonometric function solutions.Among these solutions,some are found for the first time.

  18. Effective Viscosity Coefficient of Nanosuspensions

    Science.gov (United States)

    Rudyak, V. Ya.; Belkin, A. A.; Egorov, V. V.

    2008-12-01

    Systematic calculations of the effective viscosity coefficient of nanosuspensions have been performed using the molecular dynamics method. It is established that the viscosity of a nanosuspension depends not only on the volume concentration of the nanoparticles but also on their mass and diameter. Differences from Einstein's relation are found even for nanosuspensions with a low particle concentration.

  19. Irrational "Coefficients" in Renaissance Algebra.

    Science.gov (United States)

    Oaks, Jeffrey A

    2017-06-01

    Argument From the time of al-Khwārizmī in the ninth century to the beginning of the sixteenth century algebraists did not allow irrational numbers to serve as coefficients. To multiply by x, for instance, the result was expressed as the rhetorical equivalent of . The reason for this practice has to do with the premodern concept of a monomial. The coefficient, or "number," of a term was thought of as how many of that term are present, and not as the scalar multiple that we work with today. Then, in sixteenth-century Europe, a few algebraists began to allow for irrational coefficients in their notation. Christoff Rudolff (1525) was the first to admit them in special cases, and subsequently they appear more liberally in Cardano (1539), Scheubel (1550), Bombelli (1572), and others, though most algebraists continued to ban them. We survey this development by examining the texts that show irrational coefficients and those that argue against them. We show that the debate took place entirely in the conceptual context of premodern, "cossic" algebra, and persisted in the sixteenth century independent of the development of the new algebra of Viète, Decartes, and Fermat. This was a formal innovation violating prevailing concepts that we propose could only be introduced because of the growing autonomy of notation from rhetorical text.

  20. Gradient expansion for anisotropic hydrodynamics

    Science.gov (United States)

    Florkowski, Wojciech; Ryblewski, Radoslaw; Spaliński, Michał

    2016-12-01

    We compute the gradient expansion for anisotropic hydrodynamics. The results are compared with the corresponding expansion of the underlying kinetic-theory model with the collision term treated in the relaxation time approximation. We find that a recent formulation of anisotropic hydrodynamics based on an anisotropic matching principle yields the first three terms of the gradient expansion in agreement with those obtained for the kinetic theory. This gives further support for this particular hydrodynamic model as a good approximation of the kinetic-theory approach. We further find that the gradient expansion of anisotropic hydrodynamics is an asymptotic series, and the singularities of the analytic continuation of its Borel transform indicate the presence of nonhydrodynamic modes.

  1. Gradient expansion for anisotropic hydrodynamics

    CERN Document Server

    Florkowski, Wojciech; Spaliński, Michał

    2016-01-01

    We compute the gradient expansion for anisotropic hydrodynamics. The results are compared with the corresponding expansion of the underlying kinetic-theory model with the collision term treated in the relaxation time approximation. We find that a recent formulation of anisotropic hydrodynamics based on an anisotropic matching principle yields the first three terms of the gradient expansion in agreement with those obtained for the kinetic theory. This gives further support for this particular hydrodynamic model as a good approximation of the kinetic-theory approach. We further find that the gradient expansion of anisotropic hydrodynamics is an asymptotic series, and the singularities of the analytic continuation of its Borel transform indicate the presence of non-hydrodynamic modes.

  2. Rapid mapping of volumetric machine errors using distance measurements

    Energy Technology Data Exchange (ETDEWEB)

    Krulewich, D.A.

    1998-04-01

    This paper describes a relatively inexpensive, fast, and easy to execute approach to maping the volumetric errors of a machine tool, coordinate measuring machine, or robot. An error map is used to characterize a machine or to improve its accuracy by compensating for the systematic errors. The method consists of three steps: (1) models the relationship between volumetric error and the current state of the machine, (2) acquiring error data based on distance measurements throughout the work volume; and (3)fitting the error model using the nonlinear equation for the distance. The error model is formulated from the kinematic relationship among the six degrees of freedom of error an each moving axis. Expressing each parametric error as function of position each is combined to predict the error between the functional point and workpiece, also as a function of position. A series of distances between several fixed base locations and various functional points in the work volume is measured using a Laser Ball Bar (LBB). Each measured distance is a non-linear function dependent on the commanded location of the machine, the machine error, and the location of the base locations. Using the error model, the non-linear equation is solved producing a fit for the error model Also note that, given approximate distances between each pair of base locations, the exact base locations in the machine coordinate system determined during the non-linear filling procedure. Furthermore, with the use of 2048 more than three base locations, bias error in the measuring instrument can be removed The volumetric errors of three-axis commercial machining center have been mapped using this procedure. In this study, only errors associated with the nominal position of the machine were considered Other errors such as thermally induced and load induced errors were not considered although the mathematical model has the ability to account for these errors. Due to the proprietary nature of the projects we are

  3. Equation of state for hard sphere fluids offering accurate virial coefficients

    CERN Document Server

    Tian, Jianxiang; Gui, Yuanxing; Mulero, A

    2016-01-01

    The asymptotic expansion method is extended by using currently available accurate values for the first ten virial coefficients for hard sphere fluids. It is then used to yield an equation of state for hard sphere fluids, which accurately represents the currently accepted values for the first sixteen virial coefficients and compressibility factor data in both the stable and the metastable regions of the phase diagram.

  4. New Exact Solutions to (2+1)-Dimensional Variable Coefficients Broer-Kaup Equations

    Institute of Scientific and Technical Information of China (English)

    ZHU Jia-Min; MA Zheng-Yi

    2006-01-01

    In this paper, using the variable coefficient generalized projected Ricatti equation expansion method, we present explicit solutions of the (2+1)-dimensional variable coefficients Broer-Kaup (VCBK) equations. These solutions include Weierstrass function solution, solitary wave solutions, soliton-like solutions and trigonometric function solutions.Among these solutions, some are found for the first time. Because of the three or four arbitrary functions, rich localized excitations can be found.

  5. Strategic Complexity and Global Expansion

    DEFF Research Database (Denmark)

    Oladottir, Asta Dis; Hobdari, Bersant; Papanastassiou, Marina

    2012-01-01

    The purpose of this paper is to analyse the determinants of global expansion strategies of newcomer Multinational Corporations (MNCs) by focusing on Iceland, Israel and Ireland. We argue that newcomer MNCs from small open economies pursue complex global expansion strategies (CGES). We distinguish....... The empirical evidence suggests that newcomer MNCs move away from simplistic dualities in the formulation of their strategic choices towards more complex options as a means of maintaining and enhancing their global competitiveness....

  6. Effectively control negative thermal expansion of single-phase ferroelectrics of PbTiO3-(Bi,La)FeO3 over a giant range.

    Science.gov (United States)

    Chen, Jun; Wang, Fangfang; Huang, Qingzhen; Hu, Lei; Song, Xiping; Deng, Jinxia; Yu, Ranbo; Xing, Xianran

    2013-01-01

    Control of negative thermal expansion is a fundamentally interesting topic in the negative thermal expansion materials in order for the future applications. However, it is a challenge to control the negative thermal expansion in individual pure materials over a large scale. Here, we report an effective way to control the coefficient of thermal expansion from a giant negative to a near zero thermal expansion by means of adjusting the spontaneous volume ferroelectrostriction (SVFS) in the system of PbTiO3-(Bi,La)FeO3 ferroelectrics. The adjustable range of thermal expansion contains most negative thermal expansion materials. The abnormal property of negative or zero thermal expansion previously observed in ferroelectrics is well understood according to the present new concept of spontaneous volume ferroelectrostriction. The present studies could be useful to control of thermal expansion of ferroelectrics, and could be extended to multiferroic materials whose properties of both ferroelectricity and magnetism are coupled with thermal expansion.

  7. Generalized transport coefficients for inelastic Maxwell mixtures under shear flow

    Science.gov (United States)

    Garzó, Vicente; Trizac, Emmanuel

    2015-11-01

    The Boltzmann equation framework for inelastic Maxwell models is considered to determine the transport coefficients associated with the mass, momentum, and heat fluxes of a granular binary mixture in spatially inhomogeneous states close to the simple shear flow. The Boltzmann equation is solved by means of a Chapman-Enskog-type expansion around the (local) shear flow distributions fr(0 ) for each species that retain all the hydrodynamic orders in the shear rate. Due to the anisotropy induced by the shear flow, tensorial quantities are required to describe the transport processes instead of the conventional scalar coefficients. These tensors are given in terms of the solutions of a set of coupled equations, which can be analytically solved as functions of the shear rate a , the coefficients of restitution αr s, and the parameters of the mixture (masses, diameters, and composition). Since the reference distribution functions fr(0 ) apply for arbitrary values of the shear rate and are not restricted to weak dissipation, the corresponding generalized coefficients turn out to be nonlinear functions of both a and αr s. The dependence of the relevant elements of the three diffusion tensors on both the shear rate and dissipation is illustrated in the tracer limit case, the results showing that the deviation of the generalized transport coefficients from their forms for vanishing shear rates is in general significant. A comparison with the previous results obtained analytically for inelastic hard spheres by using Grad's moment method is carried out, showing a good agreement over a wide range of values for the coefficients of restitution. Finally, as an application of the theoretical expressions derived here for the transport coefficients, thermal diffusion segregation of an intruder immersed in a granular gas is also studied.

  8. STUDY ON EFFECT OF ATMOSPHERIC PRESSURE ON VOLUMETRIC STRAIN OF INCLINED ROCK LAYER%岩层倾斜对体应变受气压影响研究

    Institute of Scientific and Technical Information of China (English)

    马京杰; 李海亮; 马相波

    2012-01-01

    On the basis of the measured data at station, when the rock layer is tilted, the interference coefficient of atmospheric pressure on volumetric strain increases significantly. By theoretical calculation, we have found that the relation of the surface inclination with coefficient of atmospheric pressure. When the interference of atmospheric pressure is removed, the earth tides observed by the volumetric strain instrument is improved significantly.%台站实测资料反映地表倾斜时,体应变气压干扰系数明显变大.通过理论计算,求出了地表倾斜度与体应变气压系数的关系,去除气压干扰后,体应变观测的固体潮汐明显改善.

  9. Phenomenological model of maize starches expansion by extrusion

    Science.gov (United States)

    Kristiawan, M.; Della Valle, G.; Kansou, K.; Ndiaye, A.; Vergnes, B.

    2016-10-01

    During extrusion of starchy products, the molten material is forced through a die so that the sudden abrupt pressure drop causes part of the water to vaporize giving an expanded, cellular structure. The objective of this work was to elaborate a phenomenological model of expansion and couple it with Ludovic® mechanistic model of twin screw extrusion process. From experimental results that cover a wide range of thermomechanical conditions, a concept map of influence relationships between input and output variables was built. It took into account the phenomena of bubbles nucleation, growth, coalescence, shrinkage and setting, in a viscoelastic medium. The input variables were the moisture content MC, melt temperature T, specific mechanical energy SME, shear viscosity η at the die exit, computed by Ludovic®, and the melt storage moduli E'(at T > Tg). The outputs of the model were the macrostructure (volumetric expansion index VEI, anisotropy) and cellular structure (fineness F) of solid foams. Then a general model was established: VEI = α (η/η0)n in which α and n depend on T, MC, SME and E' and the link between anisotropy and fineness was established.

  10. Quantitative volumetric Raman imaging of three dimensional cell cultures

    Science.gov (United States)

    Kallepitis, Charalambos; Bergholt, Mads S.; Mazo, Manuel M.; Leonardo, Vincent; Skaalure, Stacey C.; Maynard, Stephanie A.; Stevens, Molly M.

    2017-03-01

    The ability to simultaneously image multiple biomolecules in biologically relevant three-dimensional (3D) cell culture environments would contribute greatly to the understanding of complex cellular mechanisms and cell-material interactions. Here, we present a computational framework for label-free quantitative volumetric Raman imaging (qVRI). We apply qVRI to a selection of biological systems: human pluripotent stem cells with their cardiac derivatives, monocytes and monocyte-derived macrophages in conventional cell culture systems and mesenchymal stem cells inside biomimetic hydrogels that supplied a 3D cell culture environment. We demonstrate visualization and quantification of fine details in cell shape, cytoplasm, nucleus, lipid bodies and cytoskeletal structures in 3D with unprecedented biomolecular specificity for vibrational microspectroscopy.

  11. Optimization approaches to volumetric modulated arc therapy planning

    Energy Technology Data Exchange (ETDEWEB)

    Unkelbach, Jan, E-mail: junkelbach@mgh.harvard.edu; Bortfeld, Thomas; Craft, David [Department of Radiation Oncology, Massachusetts General Hospital and Harvard Medical School, Boston, Massachusetts 02114 (United States); Alber, Markus [Department of Medical Physics and Department of Radiation Oncology, Aarhus University Hospital, Aarhus C DK-8000 (Denmark); Bangert, Mark [Department of Medical Physics in Radiation Oncology, German Cancer Research Center, Heidelberg D-69120 (Germany); Bokrantz, Rasmus [RaySearch Laboratories, Stockholm SE-111 34 (Sweden); Chen, Danny [Department of Computer Science and Engineering, University of Notre Dame, Notre Dame, Indiana 46556 (United States); Li, Ruijiang; Xing, Lei [Department of Radiation Oncology, Stanford University, Stanford, California 94305 (United States); Men, Chunhua [Department of Research, Elekta, Maryland Heights, Missouri 63043 (United States); Nill, Simeon [Joint Department of Physics at The Institute of Cancer Research and The Royal Marsden NHS Foundation Trust, London SM2 5NG (United Kingdom); Papp, Dávid [Department of Mathematics, North Carolina State University, Raleigh, North Carolina 27695 (United States); Romeijn, Edwin [H. Milton Stewart School of Industrial and Systems Engineering, Georgia Institute of Technology, Atlanta, Georgia 30332 (United States); Salari, Ehsan [Department of Industrial and Manufacturing Engineering, Wichita State University, Wichita, Kansas 67260 (United States)

    2015-03-15

    Volumetric modulated arc therapy (VMAT) has found widespread clinical application in recent years. A large number of treatment planning studies have evaluated the potential for VMAT for different disease sites based on the currently available commercial implementations of VMAT planning. In contrast, literature on the underlying mathematical optimization methods used in treatment planning is scarce. VMAT planning represents a challenging large scale optimization problem. In contrast to fluence map optimization in intensity-modulated radiotherapy planning for static beams, VMAT planning represents a nonconvex optimization problem. In this paper, the authors review the state-of-the-art in VMAT planning from an algorithmic perspective. Different approaches to VMAT optimization, including arc sequencing methods, extensions of direct aperture optimization, and direct optimization of leaf trajectories are reviewed. Their advantages and limitations are outlined and recommendations for improvements are discussed.

  12. Volumetric properties of water/AOT/isooctane microemulsions.

    Science.gov (United States)

    Du, Changfei; He, Wei; Yin, Tianxiang; Shen, Weiguo

    2014-12-23

    The densities of AOT/isooctane micelles and water/AOT/isooctane microemulsions with the molar ratios R of water to AOT being 2, 8, 10, 12, 16, 18, 20, 25, 30, and 40 were measured at 303.15 K. The apparent specific volumes of AOT and the quasi-component water/AOT at various concentrations were calculated and used to estimate the volumetric properties of AOT and water in the droplets and in the continuous oil phase, to discuss the interaction between the droplets, and to determine the critical micelle concentration and the critical microemulsion concentrations. A thermodynamic model was proposed to analysis the stability boundary of the microemulsion droplets, which confirms the maximum value of R being about 65 for the stable AOT/water/isooctane microemulsion droplets.

  13. Quantitative volumetric Raman imaging of three dimensional cell cultures

    KAUST Repository

    Kallepitis, Charalambos

    2017-03-22

    The ability to simultaneously image multiple biomolecules in biologically relevant three-dimensional (3D) cell culture environments would contribute greatly to the understanding of complex cellular mechanisms and cell–material interactions. Here, we present a computational framework for label-free quantitative volumetric Raman imaging (qVRI). We apply qVRI to a selection of biological systems: human pluripotent stem cells with their cardiac derivatives, monocytes and monocyte-derived macrophages in conventional cell culture systems and mesenchymal stem cells inside biomimetic hydrogels that supplied a 3D cell culture environment. We demonstrate visualization and quantification of fine details in cell shape, cytoplasm, nucleus, lipid bodies and cytoskeletal structures in 3D with unprecedented biomolecular specificity for vibrational microspectroscopy.

  14. In-line hologram segmentation for volumetric samples.

    Science.gov (United States)

    Orzó, László; Göröcs, Zoltán; Fehér, András; Tőkés, Szabolcs

    2013-01-01

    We propose a fast, noniterative method to segment an in-line hologram of a volumetric sample into in-line subholograms according to its constituent objects. In contrast to the phase retrieval or twin image elimination algorithms, we do not aim or require to reconstruct the complex wave field of all the objects, which would be a more complex task, but only provide a good estimate about the contribution of the particular objects to the original hologram quickly. The introduced hologram segmentation algorithm exploits the special inner structure of the in-line holograms and applies only the estimated supports and reconstruction distances of the corresponding objects as parameters. The performance of the proposed method is demonstrated and analyzed experimentally both on synthetic and measured holograms. We discussed how the proposed algorithm can be efficiently applied for object reconstruction and phase retrieval tasks.

  15. Three-Dimensional Volumetric Restoration by Structural Fat Grafting

    Science.gov (United States)

    Clauser, Luigi C.; Consorti, Giuseppe; Elia, Giovanni; Galié, Manlio; Tieghi, Riccardo

    2013-01-01

    The use of adipose tissue transfer for correction of maxillofacial defects was reported for the first time at the end of the 19th century. Structural fat grafting (SFG) was introduced as a way to improve facial esthetics and in recent years has evolved into applications in craniomaxillofacial reconstructive surgery. Several techniques have been proposed for harvesting and grafting the fat. However, owing to the damage of many adipocytes during these maneuvers, the results have not been satisfactory and have required several fat injection procedures for small corrections. The author's (L.C.) overview the application of SFG in the management of volumetric deficit in the craniomaxillofacial in patients treated with a long-term follow-up. PMID:24624259

  16. Semi-automatic volumetrics system to parcellate ROI on neocortex

    Science.gov (United States)

    Tan, Ou; Ichimiya, Tetsuya; Yasuno, Fumihiko; Suhara, Tetsuya

    2002-05-01

    A template-based and semi-automatic volumetrics system--BrainVol is build to divide the any given patient brain to neo-cortical and sub-cortical regions. The standard region is given as standard ROI drawn on a standard brain volume. After normalization between the standard MR image and the patient MR image, the sub-cortical ROIs' boundary are refined based on gray matter. The neo-cortical ROIs are refined by sulcus information that is semi-automatically marked on the patient brain. Then the segmentation is applied to 4D PET image of same patient for calculation of TAC (Time Activity Curve) by co-registration between MR and PET.

  17. Out-of-core clustering of volumetric datasets

    Institute of Scientific and Technical Information of China (English)

    GRANBERG Carl J.; LI Ling

    2006-01-01

    In this paper we present a novel method for dividing and clustering large volumetric scalar out-of-core datasets. This work is based on the Ordered Cluster Binary Tree (OCBT) structure created using a top-down or divisive clustering method. The OCBT structure allows fast and efficient sub volume queries to be made in combination with level of detail (LOD) queries of the tree. The initial partitioning of the large out-of-core dataset is done by using non-axis aligned planes calculated using Principal Component Analysis (PCA). A hybrid OCBT structure is also proposed where an in-core cluster binary tree is combined with a large out-of-core file.

  18. Volumetric Survey Speed: A Figure of Merit for Transient Surveys

    CERN Document Server

    Bellm, Eric C

    2016-01-01

    Time-domain surveys can exchange sky coverage for revisit frequency, complicating the comparison of their relative capabilities. By using different revisit intervals, a specific camera may execute surveys optimized for discovery of different classes of transient objects. We propose a new figure of merit, the instantaneous volumetric survey speed, for evaluating transient surveys. This metric defines the trade between cadence interval and snapshot survey volume and so provides a natural means of comparing survey capability. The related metric of areal survey speed imposes a constraint on the range of possible revisit times: we show that many modern time-domain surveys are limited by the amount of fresh sky available each night. We introduce the concept of "spectroscopic accessibility" and discuss its importance for transient science goals requiring followup observing. We present an extension of the control time algorithm for cases where multiple consecutive detections are required. Finally, we explore how surv...

  19. Low-energy expansion formula for one-dimensional Fokker-Planck and Schr\\"odinger equations with periodic potentials

    CERN Document Server

    Miyazawa, Toru

    2011-01-01

    We study the low-energy behavior of the Green function for one-dimensional Fokker-Planck and Schr\\"odinger equations with periodic potentials. We derive a formula for the power series expansion of reflection coefficients in terms of the wave number, and apply it to the low-energy expansion of the Green function.

  20. Oxidation resistant and low coefficient of thermal expansion Nia1-CoCrAly alloy

    Science.gov (United States)

    Hebsur, Mohan G. (Inventor)

    2004-01-01

    A bond coat composition for use in thermal barrier coatings comprises a NiAl--CoCrAlY matrix containing particles of AlN dispersed therein. The bond coat composition is prepared by croymilling NiAl and CoCrAlY in liquid nitrogen.

  1. Iridescent cellulose nanocrystal/polyethylene oxide composite films with low coefficient of thermal expansion

    Science.gov (United States)

    Jairo A. Diaz; Julia L. Braun; Robert J. Moon; Jeffrey P. Youngblood

    2015-01-01

    Simultaneous control over optical and thermal properties is particularly challenging and highly desired in fields like organic electronics. Here we incorporated cellulose nanocrystals (CNCs) into polyethylene oxide (PEO) in an attempt to preserve the iridescent CNC optical reflection given by their chiral nematic organisation, while reducing the composite thermal...

  2. Joining of silicon carbide using interlayer with matching coefficient of thermal expansion

    Energy Technology Data Exchange (ETDEWEB)

    Perham, T. [Univ. of California, Berkeley, CA (United States). Dept. of Materials Science and Mineral Engineering]|[Lawrence Berkeley National Lab., CA (United States)

    1996-11-01

    The primary objective of this study is to develop a technique for joining a commercially available Silicon Carbide that gives good room temperature strength and the potential for good high temperature strength. One secondary objective is that the joining technique be adaptable to SiC{sub f}/SiC composites and/or Nickel based superalloys, and another secondary objective is that the materials provide good neutron irradiation resistance and low activation for potential application inside nuclear fusion reactors. The joining techniques studied here are: (1) reaction bonding with Al-Si/Si/SiC/C; (2) reaction/infiltration with calcium aluminum silicate; (3) ion exchange mechanism to form calcium hexaluminate (a refractory cement); and (4) oxide frit brazing with cordierite.

  3. Generalized quantum Onsager coefficients from a symmetrized Campbell-Hausdorff expansion

    NARCIS (Netherlands)

    Lendi, K.; van Wonderen, A.J.

    2001-01-01

    The analogue of the classical Onsager theory of entropy production is systematically derived for weakly irreversible processes in open quantum systems with finite-dimensional Hilbert space. The dynamics is assumed to be given by a quantum dynamical semigroup with infinitesimal generator of Gorini-Ko

  4. Deriving Second Osmotic Virial Coefficients from Equations of State and from Experiment.

    Science.gov (United States)

    Koga, K; Holten, Vincent; Widom, B

    2015-10-22

    The osmotic virial coefficients, which are measures of the effective interactions between solute molecules in dilute solution, may be obtained from expansions of the osmotic pressure or of the solute activity in powers of the solute concentration. In these expansions, the temperature is held fixed, and one additional constraint is imposed. When the additional constraint is that of fixed chemical potential of the solvent, the coefficient of the second-order term yields directly the second osmotic virial coefficient itself. Alternative constraints, such as fixed pressure, fixed solvent density, or the specification of liquid-vapor equilibrium, yield alternative measures of the solute-solute interaction, different from but related to the osmotic virial coefficient. These relations are summarized and, where new, are derived here. The coefficient in question may be calculated from equations of state in which the parameters have been obtained by fitting to other experimental properties. Alternatively, the coefficients may be calculated from direct experimental measurements of the deviations from Henry's law based on measurements of the activity of the solute in a coexisting gas phase. It is seen for propane in water as a test case that with the latter method, even with what appear to be the best available experimental data, there are still large uncertainties in the resulting second osmotic virial coefficient. With the former method, by contrast, the coefficient may be obtained with high numerical precision but then depends for its accuracy on the quality of the equation of state from which it is derived.

  5. Volumetric optical coherence microscopy enabled by aberrated optics (Conference Presentation)

    Science.gov (United States)

    Mulligan, Jeffrey A.; Liu, Siyang; Adie, Steven G.

    2017-02-01

    Optical coherence microscopy (OCM) is an interferometric imaging technique that enables high resolution, non-invasive imaging of 3D cell cultures and biological tissues. Volumetric imaging with OCM suffers a trade-off between high transverse resolution and poor depth-of-field resulting from defocus, optical aberrations, and reduced signal collection away from the focal plane. While defocus and aberrations can be compensated with computational methods such as interferometric synthetic aperture microscopy (ISAM) or computational adaptive optics (CAO), reduced signal collection must be physically addressed through optical hardware. Axial scanning of the focus is one approach, but comes at the cost of longer acquisition times, larger datasets, and greater image reconstruction times. Given the capabilities of CAO to compensate for general phase aberrations, we present an alternative method to address the signal collection problem without axial scanning by using intentionally aberrated optical hardware. We demonstrate the use of an astigmatic spectral domain (SD-)OCM imaging system to enable single-acquisition volumetric OCM in 3D cell culture over an extended depth range, compared to a non-aberrated SD-OCM system. The transverse resolution of the non-aberrated and astigmatic imaging systems after application of CAO were 2 um and 2.2 um, respectively. The depth-range of effective signal collection about the nominal focal plane was increased from 100 um in the non-aberrated system to over 300 um in the astigmatic system, extending the range over which useful data may be acquired in a single OCM dataset. We anticipate that this method will enable high-throughput cellular-resolution imaging of dynamic biological systems over extended volumes.

  6. Marginal Space Deep Learning: Efficient Architecture for Volumetric Image Parsing.

    Science.gov (United States)

    Ghesu, Florin C; Krubasik, Edward; Georgescu, Bogdan; Singh, Vivek; Yefeng Zheng; Hornegger, Joachim; Comaniciu, Dorin

    2016-05-01

    Robust and fast solutions for anatomical object detection and segmentation support the entire clinical workflow from diagnosis, patient stratification, therapy planning, intervention and follow-up. Current state-of-the-art techniques for parsing volumetric medical image data are typically based on machine learning methods that exploit large annotated image databases. Two main challenges need to be addressed, these are the efficiency in scanning high-dimensional parametric spaces and the need for representative image features which require significant efforts of manual engineering. We propose a pipeline for object detection and segmentation in the context of volumetric image parsing, solving a two-step learning problem: anatomical pose estimation and boundary delineation. For this task we introduce Marginal Space Deep Learning (MSDL), a novel framework exploiting both the strengths of efficient object parametrization in hierarchical marginal spaces and the automated feature design of Deep Learning (DL) network architectures. In the 3D context, the application of deep learning systems is limited by the very high complexity of the parametrization. More specifically 9 parameters are necessary to describe a restricted affine transformation in 3D, resulting in a prohibitive amount of billions of scanning hypotheses. The mechanism of marginal space learning provides excellent run-time performance by learning classifiers in clustered, high-probability regions in spaces of gradually increasing dimensionality. To further increase computational efficiency and robustness, in our system we learn sparse adaptive data sampling patterns that automatically capture the structure of the input. Given the object localization, we propose a DL-based active shape model to estimate the non-rigid object boundary. Experimental results are presented on the aortic valve in ultrasound using an extensive dataset of 2891 volumes from 869 patients, showing significant improvements of up to 45

  7. The volumetric rate of superluminous supernovae at z ˜ 1

    Science.gov (United States)

    Prajs, S.; Sullivan, M.; Smith, M.; Levan, A.; Karpenka, N. V.; Edwards, T. D. P.; Walker, C. R.; Wolf, W. M.; Balland, C.; Carlberg, R.; Howell, D. A.; Lidman, C.; Pain, R.; Pritchet, C.; Ruhlmann-Kleider, V.

    2017-01-01

    We present a measurement of the volumetric rate of superluminous supernovae (SLSNe) at z ˜ 1.0, measured using archival data from the first four years of the Canada-France-Hawaii Telescope Supernova Legacy Survey (SNLS). We develop a method for the photometric classification of SLSNe to construct our sample. Our sample includes two previously spectroscopically identified objects, and a further new candidate selected using our classification technique. We use the point-source recovery efficiencies from Perrett et al. and a Monte Carlo approach to calculate the rate based on our SLSN sample. We find that the three identified SLSNe from SNLS give a rate of 91^{+76}_{-36} SNe yr-1 Gpc-3 at a volume-weighted redshift of z = 1.13. This is equivalent to 2.2^{+1.8}_{-0.9}× 10^{-4} of the volumetric core-collapse supernova rate at the same redshift. When combined with other rate measurements from the literature, we show that the rate of SLSNe increases with redshift in a manner consistent with that of the cosmic star formation history. We also estimate the rate of ultra-long gamma-ray bursts based on the events discovered by the Swift satellite, and show that it is comparable to the rate of SLSNe, providing further evidence of a possible connection between these two classes of events. We also examine the host galaxies of the SLSNe discovered in SNLS, and find them to be consistent with the stellar-mass distribution of other published samples of SLSNe.

  8. Volumetric analysis of corticocancellous bones using CT data

    Energy Technology Data Exchange (ETDEWEB)

    Krappinger, Dietmar; Linde, Astrid von; Rosenberger, Ralf; Blauth, Michael [Medical University Innsbruck, Department of Trauma Surgery and Sports Medicine, Innsbruck (Austria); Glodny, Bernhard; Niederwanger, Christian [Medical University Innsbruck, Department of Radiology I, Innsbruck (Austria)

    2012-05-15

    To present a method for an automated volumetric analysis of corticocancellous bones such as the superior pubic ramus using CT data and to assess the reliability of this method. Computed tomography scans of a consecutive series of 250 patients were analyzed. A Hounsfield unit (HU) thresholding-based reconstruction technique (''Vessel Tracking,'' GE Healthcare) was used. A contiguous space of cancellous bone with similar HU values between the starting and end points was automatically identified as the region of interest. The identification was based upon the density gradient to the adjacent cortical bone. The starting point was defined as the middle of the parasymphyseal corticocancellous transition zone on the axial slice showing the parasymphyseal superior pubic ramus in its maximum anteroposterior width. The end point was defined as the middle of the periarticular corticocancellous transition zone on the axial slice showing the quadrilateral plate as a thin cortical plate. The following parameters were automatically obtained on both sides: length of the center line, volume of the superior pubic ramus between the starting point and end point, minimum, maximum and mean diameter perpendicular to the center line, and mean cross-sectional area perpendicular to the center line. An automated analysis without manual adjustments was successful in 207 patients (82.8%). The center line showed a significantly greater length in female patients (67.6 mm vs 65.0 mm). The volume was greater in male patients (21.8 cm{sup 3} vs 19.4 cm{sup 3}). The intersite reliability was high with a mean difference between the left and right sides of between 0.1% (cross-sectional area) and 2.3% (volume). The method presented allows for an automated volumetric analysis of a corticocancellous bone using CT data. The method is intended to provide preoperative information for the use of intramedullary devices in fracture fixation and percutaneous cement augmentation techniques

  9. Simulating the market coefficient of relative risk aversion

    Directory of Open Access Journals (Sweden)

    Samih Antoine Azar

    2014-12-01

    Full Text Available In this paper, expected utility, defined by a Taylor series expansion around expected wealth, is maximized. The coefficient of relative risk aversion (CRRA that is commensurate with a 100% investment in the risky asset is simulated. The following parameters are varied: the riskless return, the market standard deviation, the market stock premium, and the skewness and the kurtosis of the risky return. Both the high extremes and the low extremes are considered. With these figures, the upper bound of the market CRRA is 3.021 and the lower bound is 0.466. Log utility, which corresponds to a CRRA of 1, is not excluded.

  10. An Analysis Methodology for Stochastic Characteristic of Volumetric Error in Multiaxis CNC Machine Tool

    Directory of Open Access Journals (Sweden)

    Qiang Cheng

    2013-01-01

    Full Text Available Traditional approaches about error modeling and analysis of machine tool few consider the probability characteristics of the geometric error and volumetric error systematically. However, the individual geometric error measured at different points is variational and stochastic, and therefore the resultant volumetric error is aslo stochastic and uncertain. In order to address the stochastic characteristic of the volumetric error for multiaxis machine tool, a new probability analysis mathematical model of volumetric error is proposed in this paper. According to multibody system theory, a mean value analysis model for volumetric error is established with consideration of geometric errors. The probability characteristics of geometric errors are obtained by statistical analysis to the measured sample data. Based on probability statistics and stochastic process theory, the variance analysis model of volumetric error is established in matrix, which can avoid the complex mathematics operations during the direct differential. A four-axis horizontal machining center is selected as an illustration example. The analysis results can reveal the stochastic characteristic of volumetric error and are also helpful to make full use of the best workspace to reduce the random uncertainty of the volumetric error and improve the machining accuracy.

  11. Volumetric and two-dimensional image interpretation show different cognitive processes in learners

    NARCIS (Netherlands)

    van der Gijp, Anouk; Ravesloot, C.J.; van der Schaaf, Marieke F; van der Schaaf, Irene C; Huige, Josephine C B M; Vincken, Koen L; Ten Cate, Olle Th J; van Schaik, JPJ

    2015-01-01

    RATIONALE AND OBJECTIVES: In current practice, radiologists interpret digital images, including a substantial amount of volumetric images. We hypothesized that interpretation of a stack of a volumetric data set demands different skills than interpretation of two-dimensional (2D) cross-sectional imag

  12. Relationships between elastic anisotropy and thermal expansion in A2Mo3O12 materials.

    Science.gov (United States)

    Romao, Carl P; Donegan, S P; Zwanziger, J W; White, Mary Anne

    2016-11-09

    We report calculated elastic tensors, axial Grüneisen parameters, and thermal stress distributions in Al2Mo3O12, ZrMgMo3O12, Sc2Mo3O12, and Y2Mo3O12, a series of isomorphic materials for which the coefficients of thermal expansion range from low-positive to negative. Thermal stress in polycrystalline materials arises from interactions between thermal expansion and mechanical properties, and both can be highly anisotropic. Thermal expansion anisotropy was found to be correlated with elastic anisotropy: axes with negative thermal expansion were less compliant. Calculations of axial Grüneisen parameters revealed that the thermal expansion anisotropy in these materials is in part due to the Poisson effect. Models of thermal stress due to thermal expansion anisotropy in polycrystals following cooling showed thermal stresses of sufficient magnitude to cause microcracking in all cases. The thermal expansion anisotropy was found to couple to elastic anisotropy, decreasing the bulk coefficient of thermal expansion and leading to lognormal extremes of the thermal stress distributions.

  13. Study of Dispersion Coefficient Channel

    Science.gov (United States)

    Akiyama, K. R.; Bressan, C. K.; Pires, M. S. G.; Canno, L. M.; Ribeiro, L. C. L. J.

    2016-08-01

    The issue of water pollution has worsened in recent times due to releases, intentional or not, of pollutants in natural water bodies. This causes several studies about the distribution of pollutants are carried out. The water quality models have been developed and widely used today as a preventative tool, ie to try to predict what will be the concentration distribution of constituent along a body of water in spatial and temporal scale. To understand and use such models, it is necessary to know some concepts of hydraulic high on their application, including the longitudinal dispersion coefficient. This study aims to conduct a theoretical and experimental study of the channel dispersion coefficient, yielding more information about their direct determination in the literature.

  14. Clustering Coefficients in Multiplex Networks

    CERN Document Server

    Cozzo, Emanuele; De Domenico, Manlio; Solé, Albert; Arenas, Alex; Gómez, Sergio; Porter, Mason A; Moreno, Yamir

    2013-01-01

    Recent advances in the study of complex networked systems has highlighted that our interconnected world is made of networks that are coupled together through different layers that each stand for one type of interaction or system. Despite this situation, it is traditional to aggregate multiplex data into a single weighted network in order take advantage of existing tools. This is admittedly convenient, but it is also extremely problematic. In this paper, we generalize the concept of clustering coefficients for multiplex networks. We show how the layered structure of multiplex networks introduces a new degree of freedom that has a fundamental effect on transitivity. We compute our new multiplex clustering coefficients for several real multiplex networks and illustrate why generalizing monoplex concepts to multiplex networks must be done with great care.

  15. Reproducibility of The Random Incidence Absorption Coefficient Converted From the Sabine Absorption Coefficient

    DEFF Research Database (Denmark)

    Jeong, Cheol-Ho; Chang, Ji-ho

    2015-01-01

    Absorption coefficients measured in reverberation chambers, Sabine absorption coefficients, suffer from two major problems. Firstly, they sometimes exceed unity. Secondly, the reproducibility of the Sabine absorption coefficients is quite poor, meaning that the Sabine absorption coefficients vary...

  16. Bone lead (Pb) content at the tibia is associated with thinner distal tibia cortices and lower volumetric bone density in postmenopausal women.

    Science.gov (United States)

    Wong, Andy K O; Beattie, Karen A; Bhargava, Aakash; Cheung, Marco; Webber, Colin E; Chettle, David R; Papaioannou, Alexandra; Adachi, Jonathan D

    2015-10-01

    Conflicting evidence suggests that bone lead or blood lead may reduce areal bone mineral density (BMD). Little is known about how lead at either compartment affects bone structure. This study examined postmenopausal women (N=38, mean age 76 ± 8, body mass index (BMI): 26.74 ± 4.26 kg/m(2)) within the Hamilton cohort of the Canadian Multicentre Osteoporosis Study (CaMos), measuring bone lead at 66% of the non-dominant leg and at the calcaneus using (109)Cadmium X-ray fluorescence. Volumetric BMD and structural parameters were obtained from peripheral quantitative computed tomography images (200 μm in-plane resolution, 2.3 ± 0.5mm slice thickness) of the same 66% site and of the distal 4% site of the tibia length. Blood lead was measured using atomic absorption spectrometry and blood-to-bone lead partition coefficients (PBB, log ratio) were computed. Multivariable linear regression examined each of bone lead at the 66% tibia, calcaneus, blood lead and PBB as related to each of volumetric BMD and structural parameters, adjusting for age and BMI, diabetes or antiresorptive therapy. Regression coefficients were reported along with 95% confidence intervals. Higher amounts of bone lead at the tibia were associated with thinner distal tibia cortices (-0.972 (-1.882, -0.061) per 100 μg Pb/g of bone mineral) and integral volumetric BMD (-3.05 (-6.05, -0.05) per μg Pb/g of bone mineral). A higher PBB was associated with larger trabecular separation (0.115 (0.053, 0.178)), lower trabecular volumetric BMD (-26.83 (-50.37, -3.29)) and trabecular number (-0.08 (-0.14, -0.02)), per 100 μg Pb/g of bone mineral after adjusting for age and BMI, and remained significant while accounting for diabetes or use of antiresorptives. Total lead exposure activities related to bone lead at the calcaneus (8.29 (0.11, 16.48)) and remained significant after age and antiresorptives-adjustment. Lead accumulated in bone can have a mild insult on bone structure; but greater partitioning of lead

  17. High Volumetric Energy Density Hybrid Supercapacitors Based on Reduced Graphene Oxide Scrolls.

    Science.gov (United States)

    Rani, Janardhanan R; Thangavel, Ranjith; Oh, Se-I; Woo, Jeong Min; Chandra Das, Nayan; Kim, So-Yeon; Lee, Yun-Sung; Jang, Jae-Hyung

    2017-07-12

    The low volumetric energy density of reduced graphene oxide (rGO)-based electrodes limits its application in commercial electrochemical energy storage devices that require high-performance energy storage capacities in small volumes. The volumetric energy density of rGO-based electrode materials is very low due to their low packing density. A supercapacitor with enhanced packing density and high volumetric energy density is fabricated using doped rGO scrolls (GFNSs) as the electrode material. The restacking of rGO sheets is successfully controlled through synthesizing the doped scroll structures while increasing the packing density. The fabricated cell exhibits an ultrahigh volumetric energy density of 49.66 Wh/L with excellent cycling stability (>10 000 cycles). This unique design strategy for the electrode material has significant potential for the future supercapacitors with high volumetric energy densities.

  18. Global segmentation and curvature analysis of volumetric data sets using trivariate B-spline functions.

    Science.gov (United States)

    Soldea, Octavian; Elber, Gershon; Rivlin, Ehud

    2006-02-01

    This paper presents a method to globally segment volumetric images into regions that contain convex or concave (elliptic) iso-surfaces, planar or cylindrical (parabolic) iso-surfaces, and volumetric regions with saddle-like (hyperbolic) iso-surfaces, regardless of the value of the iso-surface level. The proposed scheme relies on a novel approach to globally compute, bound, and analyze the Gaussian and mean curvatures of an entire volumetric data set, using a trivariate B-spline volumetric representation. This scheme derives a new differential scalar field for a given volumetric scalar field, which could easily be adapted to other differential properties. Moreover, this scheme can set the basis for more precise and accurate segmentation of data sets targeting the identification of primitive parts. Since the proposed scheme employs piecewise continuous functions, it is precise and insensitive to aliasing.

  19. The duct selective volumetric receiver: potential for different selectivity strategies and stability issues

    Energy Technology Data Exchange (ETDEWEB)

    Garcia-Casals, X. [Universidad Pontificia Comillas-ICAI, Madrid (Spain). Dept. de Fluidos y Calor; Ajona, J.I. [Departamento de Energia Solar, Viessemann, Poligono Industrial San Marcos, Getafe (Spain)

    1999-07-01

    Recently much theoretical and experimental work has been conducted on volumetric receivers. However, not much attention has been paid to the possibilities of using different selectivity mechanisms to minimize radiation thermal losses, which are the main ones at high operating temperature. In this paper we present a duct volumetric receiver model and its results, which allow the evaluation of different selectivity strategies such as: conventional {epsilon}/{alpha}, geometry, frontal absorption and diffuse/specular reflection. We propose a new concept of selective volumetric receivers based on a solar-specular/infrared-diffuse radiative behaviour and evaluate its potential for efficiency improvement. In recent work on volumetric receivers based on simplified models, it has been concluded that the duct volumetric receiver is inherently unstable when working with high solar flux. We didn't find any unstable receiver behaviour even at very high solar fluxes, and conclude that a substantial potential for efficiency improvement exists if selectivity mechanisms are properly combined. (author)

  20. Enhanced volumetric visualization for real time 4D intraoperative ophthalmic swept-source OCT.

    Science.gov (United States)

    Viehland, Christian; Keller, Brenton; Carrasco-Zevallos, Oscar M; Nankivil, Derek; Shen, Liangbo; Mangalesh, Shwetha; Viet, Du Tran; Kuo, Anthony N; Toth, Cynthia A; Izatt, Joseph A

    2016-05-01

    Current-generation software for rendering volumetric OCT data sets based on ray casting results in volume visualizations with indistinct tissue features and sub-optimal depth perception. Recent developments in hand-held and microscope-integrated intrasurgical OCT designed for real-time volumetric imaging motivate development of rendering algorithms which are both visually appealing and fast enough to support real time rendering, potentially from multiple viewpoints for stereoscopic visualization. We report on an enhanced, real time, integrated volumetric rendering pipeline which incorporates high performance volumetric median and Gaussian filtering, boundary and feature enhancement, depth encoding, and lighting into a ray casting volume rendering model. We demonstrate this improved model implemented on graphics processing unit (GPU) hardware for real-time volumetric rendering of OCT data during tissue phantom and live human surgical imaging. We show that this rendering produces enhanced 3D visualizations of pathology and intraoperative maneuvers compared to standard ray casting.