WorldWideScience

Sample records for volumes source measurements

  1. Radiation Detection Equipment (RDE) Comparative Evaluation Test Program. Volume 1. Point Source Measurements

    Science.gov (United States)

    1994-08-01

    OC W 1. AGINCY USE ONLY M.enm bika ) 2. REPORT DATE 3. REPORT TYPE AND DATES COVERED I 940801 I Technical 930201 - 930731 4. TITLE AND SUB`TITLE 5...unmoderaled source. 2/18/93 Detector: Ludlum Model 15 Positve radil alis 1000. of counts 9ma A Xakn~mrfli zab .02 Lim mromm 928 32.5 100 0.040 66.7 32.5...16100 16100 161 D- 16 Table D-48. Am(U) measurement data for "strong" shielded source. (page 7 of 7) Detctor. INF Stong Am(U) Afeswemenft-Ostector lim

  2. Macular Choroidal Thickness and Volume Measured by Swept-source Optical Coherence Tomography in Healthy Korean Children.

    Science.gov (United States)

    Lee, Jung Wook; Song, In Seok; Lee, Ju-hyang; Shin, Yong Un; Lim, Han Woong; Lee, Won June; Lee, Byung Ro

    2016-02-01

    To evaluate the thickness and volume of the choroid in healthy Korean children using swept-source optical coherence tomography. We examined 80 eyes of 40 healthy children and teenagers (choroidal thickness map. We also examined 44 eyes of 35 healthy adult volunteers (≥18 years) and compared adult measurements with the findings in children. The mean age of the children and teenagers was 9.47 ± 3.80 (4 to 17) vs. 55.04 ± 12.63 years (36 to 70 years) in the adult group (p choroid were thinner (p = 0.004, p = 0.002, respectively) than the surrounding areas. The mean choroidal volumes of the inner and outer nasal areas were smaller (p = 0.004, p = 0.003, respectively) than those of all the other areas in each circle. Among the nine subfields, all areas in the children, except the outer nasal subfield, were thicker than those in adults (p choroidal thickness (p choroidal thickness and volume in children and teenagers were significantly greater than in adults. The nasal choroid was significantly thinner than the surrounding areas. The pediatric subfoveal choroid is prone to thinning with increasing age, axial length, and refractive error. These differences should be considered when choroidal thickness is evaluated in children with chorioretinal diseases.

  3. Precision volume measurement system.

    Energy Technology Data Exchange (ETDEWEB)

    Fischer, Erin E.; Shugard, Andrew D.

    2004-11-01

    A new precision volume measurement system based on a Kansas City Plant (KCP) design was built to support the volume measurement needs of the Gas Transfer Systems (GTS) department at Sandia National Labs (SNL) in California. An engineering study was undertaken to verify or refute KCP's claims of 0.5% accuracy. The study assesses the accuracy and precision of the system. The system uses the ideal gas law and precise pressure measurements (of low-pressure helium) in a temperature and computer controlled environment to ratio a known volume to an unknown volume.

  4. A compact time-of-flight SANS instrument optimised for measurements of small sample volumes at the European Spallation Source

    Science.gov (United States)

    Kynde, Søren; Hewitt Klenø, Kaspar; Nagy, Gergely; Mortensen, Kell; Lefmann, Kim; Kohlbrecher, Joachim; Arleth, Lise

    2014-11-01

    The high flux at European Spallation Source (ESS) will allow for performing experiments with relatively small beam-sizes while maintaining a high intensity of the incoming beam. The pulsed nature of the source makes the facility optimal for time-of-flight small-angle neutron scattering (ToF-SANS). We find that a relatively compact SANS instrument becomes the optimal choice in order to obtain the widest possible q-range in a single setting and the best possible exploitation of the neutrons in each pulse and hence obtaining the highest possible flux at the sample position. The instrument proposed in the present article is optimised for performing fast measurements of small scattering volumes, typically down to 2×2×2 mm3, while covering a broad q-range from about 0.005 1/Å to 0.5 1/Å in a single instrument setting. This q-range corresponds to that available at a typical good BioSAXS instrument and is relevant for a wide set of biomacromolecular samples. A central advantage of covering the whole q-range in a single setting is that each sample has to be loaded only once. This makes it convenient to use the fully automated high-throughput flow-through sample changers commonly applied at modern synchrotron BioSAXS-facilities. The central drawback of choosing a very compact instrument is that the resolution in terms of δλ / λ obtained with the short wavelength neutrons becomes worse than what is usually the standard at state-of-the-art SANS instruments. Our McStas based simulations of the instrument performance for a set of characteristic biomacromolecular samples show that the resulting smearing effects still have relatively minor effects on the obtained data and can be compensated for in the data analysis. However, in cases where a better resolution is required in combination with the large simultaneous q-range characteristic of the instrument, we show that this can be obtained by inserting a set of choppers.

  5. A compact time-of-flight SANS instrument optimised for measurements of small sample volumes at the European Spallation Source

    Energy Technology Data Exchange (ETDEWEB)

    Kynde, Søren, E-mail: kynde@nbi.ku.dk [Niels Bohr Institute, University of Copenhagen (Denmark); Hewitt Klenø, Kaspar [Niels Bohr Institute, University of Copenhagen (Denmark); Nagy, Gergely [SINQ, Paul Scherrer Institute (Switzerland); Mortensen, Kell; Lefmann, Kim [Niels Bohr Institute, University of Copenhagen (Denmark); Kohlbrecher, Joachim, E-mail: Joachim.kohlbrecher@psi.ch [SINQ, Paul Scherrer Institute (Switzerland); Arleth, Lise, E-mail: arleth@nbi.ku.dk [Niels Bohr Institute, University of Copenhagen (Denmark)

    2014-11-11

    The high flux at European Spallation Source (ESS) will allow for performing experiments with relatively small beam-sizes while maintaining a high intensity of the incoming beam. The pulsed nature of the source makes the facility optimal for time-of-flight small-angle neutron scattering (ToF-SANS). We find that a relatively compact SANS instrument becomes the optimal choice in order to obtain the widest possible q-range in a single setting and the best possible exploitation of the neutrons in each pulse and hence obtaining the highest possible flux at the sample position. The instrument proposed in the present article is optimised for performing fast measurements of small scattering volumes, typically down to 2×2×2 mm{sup 3}, while covering a broad q-range from about 0.005 1/Å to 0.5 1/Å in a single instrument setting. This q-range corresponds to that available at a typical good BioSAXS instrument and is relevant for a wide set of biomacromolecular samples. A central advantage of covering the whole q-range in a single setting is that each sample has to be loaded only once. This makes it convenient to use the fully automated high-throughput flow-through sample changers commonly applied at modern synchrotron BioSAXS-facilities. The central drawback of choosing a very compact instrument is that the resolution in terms of δλ/λ obtained with the short wavelength neutrons becomes worse than what is usually the standard at state-of-the-art SANS instruments. Our McStas based simulations of the instrument performance for a set of characteristic biomacromolecular samples show that the resulting smearing effects still have relatively minor effects on the obtained data and can be compensated for in the data analysis. However, in cases where a better resolution is required in combination with the large simultaneous q-range characteristic of the instrument, we show that this can be obtained by inserting a set of choppers.

  6. Correlation of choroidal thickness and volume measurements with axial length and age using swept source optical coherence tomography and optical low-coherence reflectometry.

    Science.gov (United States)

    Michalewski, Janusz; Michalewska, Zofia; Nawrocka, Zofia; Bednarski, Maciej; Nawrocki, Jerzy

    2014-01-01

    To report choroidal thickness and volume in healthy eyes using swept source optical coherence tomography (SS-OCT). A prospective observational study of 122 patients examined with swept source OCT (DRI-OCT, Topcon, Japan). In each eye, we performed 256 horizontal scans, 12 mm in length and centered on the fovea. We calculated choroidal thickness manually with a built-in caliper and automatically using DRI-OCT mapping software. Choroidal volume was also automatically calculated. We measured axial length with optical low-coherence reflectometry (Lenstar LS 900, Haag-Streit, Switzerland). The choroid has focally increased thickness under the fovea. Choroid was thinnest in the outer nasal quadrant. In stepwise regression analysis, age was estimated as the most significant factor correlating with decreased choroidal thickness (F=23.146, Pchoroidal thickness and volume maps. Choroidal thickness is increased at the fovea and is thinnest nasally. Age and axial length are critical for the estimation of choroidal thickness and volume. Choroidal measurements derived from SS-OCT images have potential value for objectively documenting disease-related choroidal thickness abnormalities and monitoring progressive changes over time.

  7. Volume and Surface-Enhanced Volume Negative Ion Sources

    CERN Document Server

    Stockli, M P

    2013-01-01

    H- volume sources and, especially, caesiated H- volume sources are important ion sources for generating high-intensity proton beams, which then in turn generate large quantities of other particles. This chapter discusses the physics and technology of the volume production and the caesium-enhanced (surface) production of H- ions. Starting with Bacal's discovery of the H- volume production, the chapter briefly recounts the development of some H- sources, which capitalized on this process to significantly increase the production of H- beams. Another significant increase was achieved in the 1990s by adding caesiated surfaces to supplement the volume-produced ions with surface-produced ions, as illustrated with other H- sources. Finally, the focus turns to some of the experience gained when such a source was successfully ramped up in H- output and in duty factor to support the generation of 1 MW proton beams for the Spallation Neutron Source.

  8. Cosmological Measures without Volume Weighting

    CERN Document Server

    Page, Don N

    2008-01-01

    Many cosmologists (myself included) have advocated volume weighting for the cosmological measure problem, weighting spatial hypersurfaces by their volume. However, this often leads to the Boltzmann brain problem, that almost all observations would be by momentary Boltzmann brains that arise very briefly as quantum fluctuations in the late universe when it has expanded to a huge size, so that our observations (too ordered for Boltzmann brains) would be highly atypical and unlikely. Here it is suggested that volume weighting may be a mistake. Volume averaging is advocated as an alternative. One consequence would be a loss of the argument for eternal inflation.

  9. Ultrasonographic Measures of Volume Responsiveness

    Science.gov (United States)

    2017-02-01

    AFRL-SA-WP-SR-2017-0005 Ultrasonographic Measures of Volume Responsiveness Sarah B. Murthi, MD February 2017...use, or sell any patented invention that may relate to them. Qualified requestors may obtain copies of this report from the Defense Technical...TITLE AND SUBTITLE Ultrasonographic Measures of Volume Responsiveness 5a. CONTRACT NUMBER FA8650-13-2-6D10 5b. GRANT NUMBER 5c. PROGRAM

  10. VOLUMNECT: measuring volumes with Kinect

    Science.gov (United States)

    Quintino Ferreira, Beatriz; Griné, Miguel; Gameiro, Duarte; Costeira, João. Paulo; Sousa Santos, Beatriz

    2014-03-01

    This article presents a solution to volume measurement object packing using 3D cameras (such as the Microsoft KinectTM). We target application scenarios, such as warehouses or distribution and logistics companies, where it is important to promptly compute package volumes, yet high accuracy is not pivotal. Our application auto- matically detects cuboid objects using the depth camera data and computes their volume and sorting it allowing space optimization. The proposed methodology applies to a point cloud simple computer vision and image processing methods, as connected components, morphological operations and Harris corner detector, producing encouraging results, namely an accuracy in volume measurement of 8mm. Aspects that can be further improved are identified; nevertheless, the current solution is already promising turning out to be cost effective for the envisaged scenarios.

  11. Volumetric measurement of tank volume

    Science.gov (United States)

    Walter, Richard T. (Inventor); Vanbuskirk, Paul D. (Inventor); Weber, William F. (Inventor); Froebel, Richard C. (Inventor)

    1991-01-01

    A method is disclosed for determining the volume of compressible gas in a system including incompressible substances in a zero-gravity environment consisting of measuring the change in pressure (delta P) for a known volume change rate (delta V/delta t) in the polytrophic region between isothermal and adiabatic conditions. The measurements are utilized in an idealized formula for determining the change in isothermal pressure (delta P sub iso) for the gas. From the isothermal pressure change (delta iso) the gas volume is obtained. The method is also applicable to determination of gas volume by utilizing work (W) in the compression process. In a passive system, the relationship of specific densities can be obtained.

  12. Ecr Driven Multicusp Volume h- Source

    Science.gov (United States)

    Bacal, M.; Ivanov, A. A., Jr.; Rouille, C.; Bechu, S.; Pelletier, J.

    2004-11-01

    The plasma of the source is created by seven elementary multi-dipolar ECR sources (2.45GHz). Each of these sources consists of a permanent magnet mounted at the extremity of a coaxial feedthrough. This plasma is confined by a cylindrical multicusp configuration, which traps the hot electrons at the outer boundary of the system thus favoring the creation of optimum plasma conditions necessary for H^- generation (in particular, the electron temperature of the order of 0.6 1.0 eV). We studied the density and temperature of the plasma and of the hydrogen negative ions in the center of the source, as well as the extracted currents, in the pressure range 1 to 4 mTorr, with a microwave power of 1 kW. The negative ion density measured at 4.5 to 9.5 cm from the ECR sources is going up with pressure, while the extracted current (measured at 19.5 to 24.5 cm from the sources) attains a maximum at 1.5 mTorr. Approaching the multi-dipolar sources to the extractor leads to the increase of the extracted negative ion current. Tantalum evaporation also leads to the increase of the extracted negative ion current . The effect of a collar in front of the plasma electrode will also be described. . The support of EEC (Contract HPRI-CT-2001-50021) is gratefully acknowledged.

  13. Development of production methods of volume source by the resinous solution which has hardening

    CERN Document Server

    Motoki, R

    2002-01-01

    Volume sources is used for standard sources by radioactive measurement using Ge semiconductor detector of environmental sample, e.g. water, soil and etc. that require large volume. The commercial volume source used in measurement of the water sample is made of agar-agar, and that used in measurement of the soil sample is made of alumina powder. When the plastic receptacles of this two kinds of volume sources were damaged, the leakage contents cause contamination. Moreover, if hermetically sealing performance of volume source made of agar-agar fell, volume decrease due to an evaporation off moisture gives an error to radioactive measurement. Therefore, we developed the two type methods using unsaturated polyester resin, vinilester resin, their hardening agent and acrylicresin. The first type is due to dispersing the hydrochloric acid solution included the radioisotopes uniformly in each resin and hardening the resin. The second is due to dispersing the alumina powder absorbed the radioisotopes in each resin an...

  14. Development of limb volume measuring system

    Science.gov (United States)

    Bhagat, P. K.; Kadaba, P. K.

    1983-01-01

    The mechanisms underlying the reductions in orthostatic tolerance associated with weightlessness are not well established. Contradictory results from measurements of leg volume changes suggest that altered venomotor tone and reduced blood flow may not be the only contributors to orthostatic intolerance. It is felt that a more accurate limb volume system which is insensitive to environmental factors will aid in better quantification of the hemodynamics of the leg. Of the varous limb volume techniques presently available, the ultrasonic limb volume system has proven to be the best choice. The system as described herein is free from environmental effects, safe, simple to operate and causes negligible radio frequency interference problems. The segmental ultrasonic ultrasonic plethysmograph is expected to provide a better measurement of limb volume change since it is based on cross-sectional area measurements.

  15. Measured and Calculated Volumes of Wetland Depressions

    Data.gov (United States)

    U.S. Environmental Protection Agency — Measured and calculated volumes of wetland depressions This dataset is associated with the following publication: Wu, Q., and C. Lane. Delineation and quantification...

  16. Transportation Cluster Volume 3 [Small Power Sources].

    Science.gov (United States)

    Pennsylvania State Dept. of Justice, Harrisburg. Bureau of Correction.

    The document is one of seven volumes of instructional materials developed around a cluster of Transportation Industries. Primarily technical in focus, they are designed to be used in a cluster-concept program and to integrate with a regular General Education Development (G.E.D.) program so that students may attain an employable skill level and a…

  17. A wavelength tunable photon source with sealed inner volume

    DEFF Research Database (Denmark)

    2014-01-01

    There is presented a method of providing a wavelength tunable photon source (200), comprising bonding a first element (101) with a first mirror (106), a second element (102) with a second mirror (108) and a third element (103) with a photon emitter together in a structure enclosing an inner volume...... (214) being a sealed volume, and forming a bonding interface (212) which is gas-tight, so that the first mirror (106) is placed in the inner volume (214) so the first mirror (106) may move within the inner volume (214). The method provides a relatively simple way of obtaining a tunable photon source...

  18. Measurable inhomogeneities in stock trading volume flow

    Science.gov (United States)

    Cortines, A. A. G.; Riera, R.; Anteneodo, C.

    2008-08-01

    We investigate the statistics of volumes of shares traded in stock markets. We show that the stochastic process of trading volumes can be understood on the basis of a mixed Poisson process at the microscopic time level. The beta distribution of the second kind (also known as q-gamma distribution), that has been proposed to describe empirical volume histograms, naturally results from our analysis. In particular, the shape of the distribution at small volumes is governed by the degree of granularity in the trading process, while the exponent controlling the tail is a measure of the inhomogeneities in market activity. Furthermore, the present case furnishes empirical evidence of how power law probability distributions can arise as a consequence of a fluctuating intrinsic parameter.

  19. Effects of volume conductor and source configuration on simulated magnetogastrograms

    Energy Technology Data Exchange (ETDEWEB)

    Komuro, Rie; Qiao Wenlian; Pullan, Andrew J; Cheng, Leo K, E-mail: l.cheng@auckland.ac.n [Auckland Bioengineering Institute, University of Auckland, Auckland (New Zealand)

    2010-11-21

    Recordings of the magnetic fields (MFs) arising from gastric electrical activity (GEA) have been shown to be able to distinguish between normal and certain abnormal GEA. Mathematical models provide a powerful tool for revealing the relationship between the underlying GEA and the resultant magnetogastrograms (MGGs). However, it remains uncertain the relative contributions that different volume conductor and dipole source models have on the resultant MFs. In this study, four volume conductor models (free space, sphere, half space and an anatomically realistic torso) and two dipole source configurations (containing 320 moving dipole sources and a single equivalent moving dipole source) were used to simulate the external MFs. The effects of different volume conductor models and dipole source configurations on the MF simulations were examined. The half space model provided the best approximation of the MFs produced by the torso model in the direction normal to the coronal plane. This was despite the fact that the half space model does not produce secondary sources, which have been shown to contribute up to 50% of the total MFs when an anatomically realistic torso model was used. We conclude that a realistic representation of the volume conductor and a detailed dipole source model are likely to be necessary when using a model-based approach for interpreting MGGs.

  20. Facilitating cartilage volume measurement using MRI

    Energy Technology Data Exchange (ETDEWEB)

    Maataoui, Adel, E-mail: adel.maataoui@gmx.d [Institute for Diagnostic and Interventional Radiology, Johann Wolfgang Goethe University, Theodor-Stern-Kai 7, 60590 Frankfurt am Main (Germany); Gurung, Jessen, E-mail: jessen.gurung@gmx.d [Institute for Diagnostic and Interventional Radiology, Johann Wolfgang Goethe University, Theodor-Stern-Kai 7, 60590 Frankfurt am Main (Germany); Ackermann, Hanns, E-mail: h.ackermann@add.uni-frankfurt.d [Institute for Epidemiology and Medical Statistics, Johann Wolfgang Goethe University, Theodor-Stern-Kai 7, 60590 Frankfurt am Main (Germany); Abolmaali, Nasreddin [Biological and Molecular Imaging, ZIK OncoRay - Radiation Research in Oncology, Medical Faculty Carl Gustav Carus, TU Dresden, Fetscherstrasse 74, 01307 Dresden (Germany); Kafchitsas, Konstantinos [Department of Orthopedics and Orthopedic Surgery, Johannes Gutenberg University, Langenbeckstrasse 1, 55131 Mainz (Germany); Vogl, Thomas J., E-mail: t.vogl@em.uni-frankfurt.d [Institute for Diagnostic and Interventional Radiology, Johann Wolfgang Goethe University, Theodor-Stern-Kai 7, 60590 Frankfurt am Main (Germany); Khan, M. Fawad, E-mail: fawad@gmx.d [Institute for Diagnostic and Interventional Radiology, Johann Wolfgang Goethe University, Theodor-Stern-Kai 7, 60590 Frankfurt am Main (Germany)

    2010-08-15

    Purpose: To compare quantitative cartilage volume measurement (CVM) using different slice thicknesses. Materials and methods: Ten knees were scanned with a 1.5 T MRI (Sonata, Siemens, Erlangen, Germany) using a 3D gradient echo sequence (FLASH, fast low-angle shot). Cartilage volume of the medial and lateral tibial plateau was measured by two independent readers in 1.5 mm, 3.0 mm and 5.0 mm slices using the Argus software application. Accuracy and time effectiveness served as control parameters. Results: Determining cartilage volume, time for calculation diminished for the lateral tibial plateau from 384.6 {+-} 127.7 s and 379.1 {+-} 117.6 s to 214.9 {+-} 109.9 s and 213.9 {+-} 102.2 s to 122.1 {+-} 60.1 s and 126.8 {+-} 56.2 s and for the medial tibial plateau from 465.0 {+-} 147.7 s and 461.8 {+-} 142.7 s to 214.0 {+-} 67.9 s and 208.9 {+-} 66.2 s to 132.6 {+-} 41.5 s and 130.6 {+-} 42.0 s measuring 1.5 mm, 3 mm and 5 mm slices, respectively. No statistically significant difference between cartilage volume measurements was observed (p > 0.05) while very good inter-reader correlation was evaluated. Conclusion: CVM using 1.5 mm slices provides no higher accuracy than cartilage volume measurement in 5 mm slices while an overall time saving up to 70% is possible.

  1. Utilising Geological Field Measurements and Historic Eruption Volumes to Estimate the Volume of Santorini's Magma Chamber

    Science.gov (United States)

    Browning, J.; Drymoni, K.; Gudmundsson, A.

    2015-12-01

    An understanding of the amount of magma available to supply any given eruption is useful for determining the potential eruption magnitude and duration. Geodetic measurements and inversion techniques are often used to constrain volume changes within magma chambers, as well as constrain location and depth, but such models are incapable of calculating total magma storage. For example, during the 2012 unrest period at Santorini volcano, approximately 0.021 km3 of new magma entered a shallow chamber residing at around 4 km below the surface. This type of event is not unusual, and is in fact a necessary condition for the formation of a long-lived shallow chamber, of which Santorini must possess. The period of unrest ended without culminating in eruption, i.e the amount of magma which entered the chamber was insufficient to break the chamber and force magma further towards the surface. We combine previously published data on the volume of recent eruptions at Santorini together with geodetic measurements. Measurements of dykes within the caldera wall provide an estimate of the volume of magma transported during eruptions, assuming the dyke does not become arrested. When the combined volume of a dyke and eruption are known (Ve) they can be used to estimate using fracture mechanics principles and poro-elastic constraints the size of an underlying shallow magma chamber. We present field measurements of dykes within Santorini caldera and provide an analytical method to estimate the volume of magma contained underneath Santorini caldera. In addition we postulate the potential volume of magma required as input from deeper sources to switch the shallow magma chamber from an equilibrium setting to one where the pressure inside the chamber exceeds the surrounding host rocks tensile strength, a condition necessary to form a dyke and a possible eruption.

  2. Vector velocity volume flow estimation: Sources of error and corrections applied for arteriovenous fistulas

    DEFF Research Database (Denmark)

    Jensen, Jonas; Olesen, Jacob Bjerring; Stuart, Matthias Bo

    2016-01-01

    A method for vector velocity volume flow estimation is presented, along with an investigation of its sources of error and correction of actual volume flow measurements. Volume flow errors are quantified theoretically by numerical modeling, through flow phantom measurements, and studied in vivo...... than circular, vessel area and correcting the ultrasound beam for being off-axis, gave a significant (p = 0.008) reduction in error from 31.2% to 24.3%. The error is relative to the Ultrasound Dilution Technique, which is considered the gold standard for volume flow estimation for dialysis patients....... This paper investigates errors from estimating volumetric flow using a commercial ultrasound scanner and the common assumptions made in the literature. The theoretical model shows, e.g. that volume flow is underestimated by 15%, when the scan plane is off-axis with the vessel center by 28% of the vessel...

  3. Source fields reconstruction with 3D mapping by means of the virtual acoustic volume concept

    Science.gov (United States)

    Forget, S.; Totaro, N.; Guyader, J. L.; Schaeffer, M.

    2016-10-01

    This paper presents the theoretical framework of the virtual acoustic volume concept and two related inverse Patch Transfer Functions (iPTF) identification methods (called u-iPTF and m-iPTF depending on the chosen boundary conditions for the virtual volume). They are based on the application of Green's identity on an arbitrary closed virtual volume defined around the source. The reconstruction of sound source fields combines discrete acoustic measurements performed at accessible positions around the source with the modal behavior of the chosen virtual acoustic volume. The mode shapes of the virtual volume can be computed by a Finite Element solver to handle the geometrical complexity of the source. As a result, it is possible to identify all the acoustic source fields at the real surface of an irregularly shaped structure and irrespective of its acoustic environment. The m-iPTF method is introduced for the first time in this paper. Conversely to the already published u-iPTF method, the m-iPTF method needs only acoustic pressure and avoids particle velocity measurements. This paper is focused on its validation, both with numerical computations and by experiments on a baffled oil pan.

  4. New concept of ECR driven multicusp volume H- source

    Science.gov (United States)

    Bacal, M.; Ivanov, A. A., Jr.; Rouillé, C.; Arnal, Y.; Béchu, S.; Pelletier, J.

    2003-10-01

    We propose a new concept of a large volume H- source. The plasma necessary to generate the negative hydrogen ions is created by several elementary multi-dipolar ECR sources. Each of these sources consists of a permanent magnet mounted at the extremity of a coaxial feedthrough. This plasma is confined in a periodic magnetic field configuration known as multicusp configuration. It traps the hot electrons at the outer boundary of the system thus favoring the creation of optimum plasma conditions necessary for H- generation (in particular, the electron temperature of the order of 0.6 - 0.8 eV). To test this idea we installed seven ECR sources (2.45GHz) on the top flange of the volume H- source Camembert III with its cylindrical multicusp configuration. The pressure was varied from 1 to 4 mTorr, the total power of the microwave generator was varied between 500 W and 1 kW. We studied the density and temperature of the plasma and of the hydrogen negative ions. We obtained encouraging results confirming the generation of the optimum plasma conditions in this system. We also compared the obtained results with the previous generation scheme, using filaments. Acknowledgement. The support of EEC (Contract HPRI-CT-2001-50021) is gratefully acknowledged.

  5. The validity and reliability of computed tomography orbital volume measurements.

    Science.gov (United States)

    Diaconu, Silviu C; Dreizin, David; Uluer, Mehmet; Mossop, Corey; Grant, Michael P; Nam, Arthur J

    2017-09-01

    Orbital volume calculations allow surgeons to design patient-specific implants to correct volume deficits. It is estimated that changes as small as 1 ml in orbital volume can lead to enophthalmos. Awareness of the limitations of orbital volume computed tomography (CT) measurements is critical to differentiate between true volume differences and measurement error. The aim of this study is to analyze the validity and reliability of CT orbital volume measurements. A total of 12 cadaver orbits were scanned using a standard CT maxillofacial protocol. Each orbit was dissected to isolate the extraocular muscles, fatty tissue, and globe. The empty bony orbital cavity was then filled with sculpting clay. The volumes of the muscle, fat, globe, and clay (i.e., bony orbital cavity) were then individually measured via water displacement. The CT-derived volumes, measured by manual segmentation, were compared to the direct measurements to determine validity. The difference between CT orbital volume measurements and physically measured volumes is not negligible. Globe volumes have the highest agreement with 95% of differences between -0.5 and 0.5 ml, bony volumes are more likely to be overestimated with 95% of differences between -1.8 and 2.6 ml, whereas extraocular muscle volumes have poor validity and should be interpreted with caution. Copyright © 2017 European Association for Cranio-Maxillo-Facial Surgery. Published by Elsevier Ltd. All rights reserved.

  6. Accuracy and Sources of Error for an Angle Independent Volume Flow Estimator

    DEFF Research Database (Denmark)

    Jensen, Jonas; Olesen, Jacob Bjerring; Hansen, Peter Møller

    2014-01-01

    This paper investigates sources of error for a vector velocity volume flow estimator. Quantification of the estima tor’s accuracy is performed theoretically and investigated in vivo . Womersley’s model for pulsatile flow is used to simulate velo city profiles and calculate volume flow errors in c...... % underestimated volume flow according to the simulation. Volume flow estimates were corrected for the beam being off- axis, but was not able to significantly decrease the error rel ative to measurements with the reference method.......This paper investigates sources of error for a vector velocity volume flow estimator. Quantification of the estima tor’s accuracy is performed theoretically and investigated in vivo . Womersley’s model for pulsatile flow is used to simulate velo city profiles and calculate volume flow errors....... A BK Medical UltraView 800 ultrasound scanner with a 9 MHz linear array transducer is used to obtain Vector Flow Imaging sequences of a superficial part of the fistulas. Cross-sectional diameters of each fistu la are measured on B-mode images by rotating the scan plane 90 degrees. The major axis...

  7. Vector velocity volume flow estimation: Sources of error and corrections applied for arteriovenous fistulas.

    Science.gov (United States)

    Jensen, Jonas; Olesen, Jacob Bjerring; Stuart, Matthias Bo; Hansen, Peter Møller; Nielsen, Michael Bachmann; Jensen, Jørgen Arendt

    2016-08-01

    A method for vector velocity volume flow estimation is presented, along with an investigation of its sources of error and correction of actual volume flow measurements. Volume flow errors are quantified theoretically by numerical modeling, through flow phantom measurements, and studied in vivo. This paper investigates errors from estimating volumetric flow using a commercial ultrasound scanner and the common assumptions made in the literature. The theoretical model shows, e.g. that volume flow is underestimated by 15%, when the scan plane is off-axis with the vessel center by 28% of the vessel radius. The error sources were also studied in vivo under realistic clinical conditions, and the theoretical results were applied for correcting the volume flow errors. Twenty dialysis patients with arteriovenous fistulas were scanned to obtain vector flow maps of fistulas. When fitting an ellipsis to cross-sectional scans of the fistulas, the major axis was on average 10.2mm, which is 8.6% larger than the minor axis. The ultrasound beam was on average 1.5mm from the vessel center, corresponding to 28% of the semi-major axis in an average fistula. Estimating volume flow with an elliptical, rather than circular, vessel area and correcting the ultrasound beam for being off-axis, gave a significant (p=0.008) reduction in error from 31.2% to 24.3%. The error is relative to the Ultrasound Dilution Technique, which is considered the gold standard for volume flow estimation for dialysis patients. The study shows the importance of correcting for volume flow errors, which are often made in clinical practice.

  8. Measuring TGV source strength with Syntacan

    NARCIS (Netherlands)

    Toorn, J.D. van der; Hendriks, H.; Dool, T.C. van den

    1996-01-01

    A 10 m high, vertical, synthetic acoustic antenna (Syntacan) has been used to measure the acoustic source strength and the vertical source distribution of a French TGV, as a function of the speed of the train, the frequency of the sound and the coach type (passenger coach, power car). The results ar

  9. Measuring TGV source strength with Syntacan

    NARCIS (Netherlands)

    Toorn, J.D. van der; Hendriks, H.; Dool, T.C. van den

    1996-01-01

    A 10 m high, vertical, synthetic acoustic antenna (Syntacan) has been used to measure the acoustic source strength and the vertical source distribution of a French TGV, as a function of the speed of the train, the frequency of the sound and the coach type (passenger coach, power car). The results

  10. Study on paper moisture measurement method by monochromatic light sources

    Science.gov (United States)

    Mo, Changtao; Du, Xin; He, Ping; Zhang, Lili; Li, Nan; Wang, Ming

    2010-10-01

    We design the emission and detection optical paths of three monochromatic infrared light sources with different wavelength. The three light sources are placed according to the different angles, so that the three kinds of monochromatic lights are converged on the same point of the sample. Using the method, we can detect the same point and improve the measurement accuracy. We choose the standard near-infrared monochromatic light source, so that we can save some equipments, such as tungsten- halogen lamp, filtered wheel, collimation focalizer, electric machine, and so on. In particular, we save the cumbersome cooling system, reduce the volume of the instrument greatly and reduce the cost. The three monochromatic light sources are supplied by the same pulse power source, to ensure their synchronous working.

  11. Dose measurements around spallation neutron sources.

    Science.gov (United States)

    Fragopoulou, M; Stoulos, S; Manolopoulou, M; Krivopustov, M; Zamani, M

    2008-01-01

    Neutron dose measurements and calculations around spallation sources appear to be of great importance in shielding research. Two spallation sources were irradiated by high-energy proton beams delivered by the Nuclotron accelerator (JINR), Dubna. Neutrons produced by the spallation sources were measured by using solid-state nuclear track detectors. In addition, neutron dose was calculated after polyethylene and concrete, using a phenomenological model based on empirical relations applied in high-energy physics. The study provides an analytical and experimental neutron benchmark analysis using the transmission factor and a comparison between the experimental results and calculations.

  12. Tank waste source term inventory validation. Volume 1. Letter report

    Energy Technology Data Exchange (ETDEWEB)

    Brevick, C.H.; Gaddis, L.A.; Johnson, E.D.

    1995-04-28

    The sample data for selection of 11 radionuclides and 24 chemical analytes were extracted from six separate sample data sets, were arranged in a tabular format and were plotted on scatter plots for all of the 149 single-shell tanks, the 24 double-shell tanks and the four aging waste tanks. The solid and liquid sample data was placed in separate tables and plots. The sample data and plots were compiled from the following data sets: characterization raw sample data, recent core samples, D. Braun data base, Wastren (Van Vleet) data base, TRAC and HTCE inventories. This document is Volume I of the Letter Report entitled Tank Waste Source Term Inventory Validation.

  13. Advanced Photon Source research: Volume 1, Number 1, April 1998

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-04-01

    The following articles are included in this publication: (1) The Advanced Photon Source: A Brief Overview; (2) MAD Analysis of FHIT at the Structural Biology Center; (3) Advances in High-Energy-Resolution X-ray Scattering at Beamline 3-ID; (4) X-ray Imaging and Microspectroscopy of the Mycorrhyizal Fungus-Plant Symbiosis; (5) Measurement and Control of Particle-beam Trajectories in the Advanced Photon Storage Ring; (6) Beam Acceleration and Storage at the Advanced Photon Source; and (7) Experimental Facilities Operations and Current Status.

  14. Residual limb volume change: Systematic review of measurement and management

    Directory of Open Access Journals (Sweden)

    Joan E. Sanders, PhD

    2011-10-01

    Full Text Available Management of residual limb volume affects decisions regarding timing of fit of the first prosthesis, when a new prosthetic socket is needed, design of a prosthetic socket, and prescription of accommodation strategies for daily volume fluctuations. This systematic review assesses what is known about measurement and management of residual limb volume change in persons with lower-limb amputation. Publications that met inclusion criteria were grouped into three categories: group I: descriptions of residual limb volume measurement techniques; group II: studies investigating the effect of residual limb volume change on clinical care in people with lower-limb amputation; and group III: studies of residual limb volume management techniques or descriptions of techniques for accommodating or controlling residual limb volume. We found that many techniques for the measurement of residual limb volume have been described but clinical use is limited largely because current techniques lack adequate resolution and in-socket measurement capability. Overall, limited evidence exists regarding the management of residual limb volume, and the evidence available focuses primarily on adults with transtibial amputation in the early postoperative phase. While we can draw some insights from the available research about residual limb volume measurement and management, further research is required.

  15. High dose rate brachytherapy source measurement intercomparison.

    Science.gov (United States)

    Poder, Joel; Smith, Ryan L; Shelton, Nikki; Whitaker, May; Butler, Duncan; Haworth, Annette

    2017-06-01

    This work presents a comparison of air kerma rate (AKR) measurements performed by multiple radiotherapy centres for a single HDR (192)Ir source. Two separate groups (consisting of 15 centres) performed AKR measurements at one of two host centres in Australia. Each group travelled to one of the host centres and measured the AKR of a single (192)Ir source using their own equipment and local protocols. Results were compared to the (192)Ir source calibration certificate provided by the manufacturer by means of a ratio of measured to certified AKR. The comparisons showed remarkably consistent results with the maximum deviation in measurement from the decay-corrected source certificate value being 1.1%. The maximum percentage difference between any two measurements was less than 2%. The comparisons demonstrated the consistency of well-chambers used for (192)Ir AKR measurements in Australia, despite the lack of a local calibration service, and served as a valuable focal point for the exchange of ideas and dosimetry methods.

  16. Software Development for JSA Source Jerk Measurement

    Institute of Scientific and Technical Information of China (English)

    LUO; Huang-da; ZHANG; Tao

    2013-01-01

    We have developed a series of experiment measurement system for Jordan sub-critical assembly.The source jerk measurement system is used for measuring the reactivity of sub-critical reactor.It mainlyconsists of a BF3 neutron detector around the reactor core,main amplifier,the data acquisition and processing software.The software acquires neutron pulse data by controlling DAQ card,and displaying

  17. Clinical Relevance of Brain Volume Measures in Multiple Sclerosis

    DEFF Research Database (Denmark)

    De Stefano, Nicola; Airas, Laura; Grigoriadis, Nikolaos

    2014-01-01

    (e.g. SIENA [Structural Image Evaluation using Normalization of Atrophy]). Although these methods are sensitive and reproducible, caution must be exercised when interpreting brain volume data, as numerous factors (e.g. pseudoatrophy) may have a confounding effect on measurements, especially...... therefore have important clinical implications affecting treatment decisions, with several clinical trials now demonstrating an effect of disease-modifying treatments (DMTs) on reducing brain volume loss. In clinical practice, it may therefore be important to consider the potential impact of a therapy...... on reducing the rate of brain volume loss. This article reviews the measurement of brain volume in clinical trials and practice, the effect of DMTs on brain volume change across trials and the clinical relevance of brain volume loss in MS....

  18. ECR-Driven Multicusp Volume H- Ion Source

    Science.gov (United States)

    Bacal, M.; Ivanov, A. A.; Rouillé, C.; Svarnas, P.; Béchu, S.; Pelletier, J.

    2005-04-01

    We studied the negative ion current extracted from the plasma created by seven elementary ECR sources, operating at 2.45 GHz, placed in the magnetic multipole chamber "Camembert III". We varied the pressure from 1 to 4 mTorr, with a maximum power of 1 kW and studied the plasma created in this system by measuring the various plasma parameters, including the density and temperature of the negative hydrogen ions. We found that the electron temperature is optimal for negative hydrogen ion production at 9.5 cm from the ECR sources. The tantalum-covered wall surface pollution reduces the extracted negative ion current and enhances the electron current. Tantalum evaporation has a positive effect. The use of a grid and of a collar in front of the plasma electrode did not lead to any enhancement of the extracted negative ion current.

  19. Beam emittance measurements on multicusp ion sources

    Energy Technology Data Exchange (ETDEWEB)

    Sarstedt, M.; Lee, Y.; Leung, K.N.; Perkins, L.T.; Pickard, D.S.; Weber, M.; Williams, M.D.

    1995-08-01

    Multicusp ion sources are used for various applications. Presently, the implementation of this type of ion source is planned for the development of an ion beam lithography machine, which will be used for the projection of sub-0.2 micron patterns onto a wafer substrate. Since, for this application, a very good beam quality and a small ion energy spread are required, emittance measurements have been performed on a multicusp ion source for various source conditions. It is shown that the installation of proper capacitors between the extraction electrodes is necessary to avoid rf-pickup, which otherwise leads to a distortion of the beam emittance. The influence of the magnetic filter field on the beam emittance has been investigated, and the beam emittance of a dc filament-discharge plasma has also been compared to that of an rf-generated plasma.

  20. Beam emittance measurements on multicusp ion sources

    Energy Technology Data Exchange (ETDEWEB)

    Sarstedt, M.; Lee, Y.; Leung, K.N. [and others

    1995-08-01

    Multicusp ion sources are used for various applications. Presently, the implementation of this type of ion source planned for the development of an ion beam lithography machine, which will be used for the projection of sub-0.2 {mu}m patterns onto a wafer substrate. Since, for this application, a very good beam quality and a small ion energy spread are required, emittance measurements have been performed on a multicusp ion source for various source conditions. It is shown that the installation of proper capacitors between the extraction electrodes is necessary to avoid rf-pickup, which otherwise leads to a distortion of the beam emittance. The influence of the magnetic filter field on the beam emittance has been investigated, and the beam emittance of a dc filament-discharge plasma has also been compared to that of an rf-generated plasma.

  1. Beam emittance measurements on multicusp ion sources

    Energy Technology Data Exchange (ETDEWEB)

    Sarstedt, M.; Lee, Y.; Leung, K.N.; Perkins, L.T.; Pickard, D.S.; Weber, M.; Williams, M.D. [Lawrence Berkeley National Laboratory, University of California, Berkeley, California 94720 (United States)

    1996-03-01

    Multicusp ion sources are used for various applications. Presently, the implementation of this type of ion source is planned for the development of an ion beam lithography machine, which will be used for the projection of sub-0.2 {mu}m patterns onto a wafer substrate. Since, for this application, a very good beam quality and a small ion energy spread are required, emittance measurements have been performed on a multicusp ion source for various source conditions. It is shown that the installation of proper capacitors between the extraction electrodes is necessary to avoid rf pickup, which otherwise leads to a distortion of the beam emittance. The influence of the magnetic filter field on the beam emittance has been investigated, and the beam emittance of a dc filament-discharge plasma has also been compared to that of a rf-generated plasma. {copyright} {ital 1996 American Institute of Physics.}

  2. Beam emittance measurements on multicusp ion sources

    Science.gov (United States)

    Sarstedt, M.; Lee, Y.; Leung, K. N.; Perkins, L. T.; Pickard, D. S.; Weber, M.; Williams, M. D.

    1996-03-01

    Multicusp ion sources are used for various applications. Presently, the implementation of this type of ion source is planned for the development of an ion beam lithography machine, which will be used for the projection of sub-0.2 μm patterns onto a wafer substrate. Since, for this application, a very good beam quality and a small ion energy spread are required, emittance measurements have been performed on a multicusp ion source for various source conditions. It is shown that the installation of proper capacitors between the extraction electrodes is necessary to avoid rf pickup, which otherwise leads to a distortion of the beam emittance. The influence of the magnetic filter field on the beam emittance has been investigated, and the beam emittance of a dc filament-discharge plasma has also been compared to that of a rf-generated plasma.

  3. The effect of fiber orientation on volume measurement using conductance catheter techniques.

    Science.gov (United States)

    Thaijiam, C; Gale, T J

    2006-01-01

    Estimation of parallel conductance using the impedance electrode technique is usually done assuming isotropic conditions. This may not be the best solution since the myocardium is an anisotropic material. This paper exposes the effect of fiber orientation for volume measurement using a conductor model with asymmetrical source electrodes. Simulation results show calculated volumes between surrounding materials with and without myocardial fiber orientation included in the model. We plan to extend these study results to the real heart for developing conductance catheter techniques for use in blood volume measurements in the right ventricle.

  4. Measuring angular diameters of extended sources

    NARCIS (Netherlands)

    van Hoof, PAM

    2000-01-01

    When measuring diameters of partially resolved sources like planetary nebulae, H II regions or galaxies, often a technique called Gaussian deconvolution is used. This technique yields a Gaussian diameter, which subsequently has to be multiplied by a conversion factor to obtain the true angular

  5. Translation Invariant Extensions of Finite Volume Measures

    Science.gov (United States)

    Goldstein, S.; Kuna, T.; Lebowitz, J. L.; Speer, E. R.

    2017-02-01

    We investigate the following questions: Given a measure μ _Λ on configurations on a subset Λ of a lattice L, where a configuration is an element of Ω ^Λ for some fixed set Ω , does there exist a measure μ on configurations on all of L, invariant under some specified symmetry group of L, such that μ _Λ is its marginal on configurations on Λ ? When the answer is yes, what are the properties, e.g., the entropies, of such measures? Our primary focus is the case in which L=Z^d and the symmetries are the translations. For the case in which Λ is an interval in Z we give a simple necessary and sufficient condition, local translation invariance ( LTI), for extendibility. For LTI measures we construct extensions having maximal entropy, which we show are Gibbs measures; this construction extends to the case in which L is the Bethe lattice. On Z we also consider extensions supported on periodic configurations, which are analyzed using de Bruijn graphs and which include the extensions with minimal entropy. When Λ subset Z is not an interval, or when Λ subset Z^d with d>1, the LTI condition is necessary but not sufficient for extendibility. For Z^d with d>1, extendibility is in some sense undecidable.

  6. Translation Invariant Extensions of Finite Volume Measures

    Science.gov (United States)

    Goldstein, S.; Kuna, T.; Lebowitz, J. L.; Speer, E. R.

    2016-08-01

    We investigate the following questions: Given a measure μ _Λ on configurations on a subset Λ of a lattice L, where a configuration is an element of Ω ^Λ for some fixed set Ω , does there exist a measure μ on configurations on all of L, invariant under some specified symmetry group of L, such that μ _Λ is its marginal on configurations on Λ ? When the answer is yes, what are the properties, e.g., the entropies, of such measures? Our primary focus is the case in which L=Z^d and the symmetries are the translations. For the case in which Λ is an interval in Z we give a simple necessary and sufficient condition, local translation invariance (LTI), for extendibility. For LTI measures we construct extensions having maximal entropy, which we show are Gibbs measures; this construction extends to the case in which L is the Bethe lattice. On Z we also consider extensions supported on periodic configurations, which are analyzed using de Bruijn graphs and which include the extensions with minimal entropy. When Λ subset Z is not an interval, or when Λ subset Z^d with d>1 , the LTI condition is necessary but not sufficient for extendibility. For Z^d with d>1 , extendibility is in some sense undecidable.

  7. Measuring glioma volumes: A comparison of linear measurement based formulae with the manual image segmentation technique

    Directory of Open Access Journals (Sweden)

    Sanjeev A Sreenivasan

    2016-01-01

    Conclusions: Manual region of interest-based image segmentation is the standard technique for measuring glioma volumes. For routine clinical use, the simple formula v = abc/2 (or the formula for volume of an ellipsoid could be used as alternatives.

  8. Transcutaneous measurement of volume blood flow

    Science.gov (United States)

    Daigle, R. E.; Mcleod, F. D.; Miller, C. W.; Histand, M. B.; Wells, M. K.

    1974-01-01

    Blood flow velocity measurements, using Doppler velocimeter, are described. The ability to measure blood velocity using ultrasound is derived from the Doppler effect; the change in frequency which occurs when sound is reflected or transmitted from a moving target. When ultrasound of the appropriate frequency is transmitted through a moving blood stream, the blood cells act as point scatterers of ultrasonic energy. If this scattered ultrasonic energy is detected, it is found to be shifted in frequency according to the velocity of the blood cells, nu, the frequency of the incident sound, f sub o, the speed of sound in the medium, c, and the angle between the sound beam and the velocity vector, o. The relation describing this effect is known as the Doppler equation. Delta f = 2 f sub o x nu x cos alpha/c. The theoretical and experimental methods are evaluated.

  9. Analysis of Partial Volume Effects on Accurate Measurement of the Hippocampus Volume

    Institute of Scientific and Technical Information of China (English)

    Maryam Hajiesmaeili; Jamshid Dehmeshki; Tim Ellis

    2014-01-01

    Hippocampal volume loss is an important biomarker in distinguishing subjects with Alzheimer’s disease (AD) and its measurement in magnetic resonance images (MRI) is influenced by partial volume effects (PVE). This paper describes a post-processing approach to quantify PVE for correction of the hippocampal volume by using a spatial fuzzyC-means (SFCM) method. The algorithm is evaluated on a dataset of 20 T1-weighted MRI scans sampled at two different resolutions. The corrected volumes for left and right hippocampus (HC) which are 23% and 18% for the low resolution and 6% and 5% for the high resolution datasets, respectively are lower than hippocampal volume results from manual segmentation. Results show the importance of applying this technique in AD detection with low resolution datasets.

  10. Measurement of neutron diffraction with compact neutron source RANS

    Science.gov (United States)

    Ikeda, Y.; Takamura, M.; Taketani, A.; Sunaga, H.; Otake, Y.; Suzuki, H.; Kumagai, M.; Oba, Y.; Hama, T.

    2016-11-01

    Diffraction is used as a measurement technique for crystal structure. X-rays or electron beam with wavelength that is close to the lattice constant of the crystal is often used for the measurement. They have sensitivity in surface (0.01mm) of heavy metals due to the mean free path for heavy ions. Neutron diffraction has the probe of the internal structure of the heavy metals because it has a longer mean free path than that of the X-rays or the electrons. However, the neutron diffraction measurement is not widely used because large facilities are required in the many neutron sources. RANS (Riken Accelerator-driven Compact Neutron Source) is developed as a neutron source which is usable easily in laboratories and factories. In RANS, fast neutrons are generated by 7MeV protons colliding on a Be target. Some fast neutrons are moderated with polyethylene to thermal neutrons. The thermal neutrons of 10meV which have wavelength of 10nm can be used for the diffraction measurement. In this study, the texture evolution in steels was measured with RANS and the validity of the compact neutron source was proved. The texture of IF steel sheets with the thickness of 1.0mm was measured with 10minutes run. The resolution is 2% and is enough to analyze a evolution in texture due to compression/tensile deformation or a volume fraction of two phases in the steel sample. These results have proven the possibility to use compact neutron source for the analysis of mesoscopic structure of metallic materials.

  11. Measuring Modularity in Open Source Code Bases

    Directory of Open Access Journals (Sweden)

    Roberto Milev

    2009-03-01

    Full Text Available Modularity of an open source software code base has been associated with growth of the software development community, the incentives for voluntary code contribution, and a reduction in the number of users who take code without contributing back to the community. As a theoretical construct, modularity links OSS to other domains of research, including organization theory, the economics of industry structure, and new product development. However, measuring the modularity of an OSS design has proven difficult, especially for large and complex systems. In this article, we describe some preliminary results of recent research at Carleton University that examines the evolving modularity of large-scale software systems. We describe a measurement method and a new modularity metric for comparing code bases of different size, introduce an open source toolkit that implements this method and metric, and provide an analysis of the evolution of the Apache Tomcat application server as an illustrative example of the insights gained from this approach. Although these results are preliminary, they open the door to further cross-discipline research that quantitatively links the concerns of business managers, entrepreneurs, policy-makers, and open source software developers.

  12. Measuring industrial energy efficiency: Physical volume versus economic value

    Energy Technology Data Exchange (ETDEWEB)

    Freeman, S.L.; Niefer, M.J.; Roop, J.M.

    1996-12-01

    This report examines several different measures of industrial output for use in constructing estimates of industrial energy efficiency and discusses some reasons for differences between the measures. Estimates of volume-based measures of output, as well as 3 value-based measures of output (value of production, value of shipments, and value added), are evaluated for 15 separate 4-digit industries. Volatility, simple growth rate, and trend growth rate estimates are made for each industry and each measure of output. Correlations are made between the volume- and value-based measures of output. Historical energy use data are collected for 5 of the industries for making energy- intensity estimates. Growth rates in energy use, energy intensity, and correlations between volume- and value-based measures of energy intensity are computed. There is large variability in growth trend estimates both long term and from year to year. While there is a high correlation between volume- and value-based measures of output for a few industries, typically the correlation is low, and this is exacerbated for estimates of energy intensity. Analysis revealed reasons for these low correlations. It appears that substantial work must be done before reliable measures of trends in the energy efficiency of industry can be accurately characterized.

  13. A STUDY ON MORPHOMETRIC MEASUREMENT OF VOLUME OF ACETABULUM

    Directory of Open Access Journals (Sweden)

    Leena Khobragade,

    2014-09-01

    Full Text Available Background: Hip joint represents an unique functional unit and has complex biomechanical construction. In today’s era where total hip replacement surgeries have made their way it has become imperative for the anatomists to know the variations in acetabular dimensions. Reconstruction of acetabulum in patients with significant acetabular bone deficiency remains a challenge. Hence the present study was carried out with the aim to study the morphometric measurement of volume of acetabulum in both the sexes. Materials and Methods: Material of the study consisted of 110 human hip bones (60 males and 50 females. Volume of Acetabulum (VA was measured on these hip bones on both the sides. Statistical analysis was done using SPSS (Statistical Package for the Social Sciences version 11 and Microsoft Excel 2007. Results: The mean volume of acetabulum in male was 23.13 ml and female was 17.88 ml. The mean volume of acetabulum on right side was 20.55 ml and left side was 20.91 ml. Volume of the acetabulum was greater in males as compared to females and the differences were statistically significant. Volume was greater on the left side as compared to the right side but the difference was statistically non significant. Discussion: Analysing the differences on human acetabulum is helpful in understanding not only morphological but also medicolegal aspects. Conclusion: Volume of the acetabulum was greater in males as compared to females.

  14. The bigger, the better? Volume measurements of parasites and hosts

    DEFF Research Database (Denmark)

    Nagler, Christina; Hörnig, Marie K.; Haug, Joachim T.

    2017-01-01

    . Using advanced imaging methods (micro-CT in conjunction with 3D modeling), we measured the volume of parasitic structures (externa, interna, egg mass, egg number, visceral mass) and the volume of the entire host. Our results show positive correlations between the volume of (1) entire rhizocephalan...... (externa + interna) and host body, (2) rhizocephalan externa and host body, (3) rhizocephalan visceral mass and rhizocephalan body, (4) egg mass and rhizocephalan externa, (5) rhizocephalan egg mass and their egg number. Comparing the rhizocephalan Sylon hippolytes, a parasite of caridean shrimps...

  15. On-line Measuring Method for Shell Chamber Volume

    Institute of Scientific and Technical Information of China (English)

    ZHANG Li-zhong; WANG De-min; JIANG Tao; CAO Guo-hua; WANG Qi

    2005-01-01

    Using the ideal gas state equation, an on-line measuring method for the shell chamber volume is studied in this paper. After analyzing how various measurement parameters affect the measurement accuracy, the system parameters are optimized in this method. Because the shape and volume of the tested items are similar, the method of using "tamping" to raise the accuracy and speed of the measurement is put forward. Based on the work above, a prototype of the testing instrument for shell chamber volume was developed, automatically testing and controlling. Compared with the method of "water weight", this method is more accurate, quicker and more automotive, so it is adaptable for the use of on-line detection.

  16. Method for measuring anterior chamber volume by image analysis

    Science.gov (United States)

    Zhai, Gaoshou; Zhang, Junhong; Wang, Ruichang; Wang, Bingsong; Wang, Ningli

    2007-12-01

    Anterior chamber volume (ACV) is very important for an oculist to make rational pathological diagnosis as to patients who have some optic diseases such as glaucoma and etc., yet it is always difficult to be measured accurately. In this paper, a method is devised to measure anterior chamber volumes based on JPEG-formatted image files that have been transformed from medical images using the anterior-chamber optical coherence tomographer (AC-OCT) and corresponding image-processing software. The corresponding algorithms for image analysis and ACV calculation are implemented in VC++ and a series of anterior chamber images of typical patients are analyzed, while anterior chamber volumes are calculated and are verified that they are in accord with clinical observation. It shows that the measurement method is effective and feasible and it has potential to improve accuracy of ACV calculation. Meanwhile, some measures should be taken to simplify the handcraft preprocess working as to images.

  17. Micro analysis of fringe field formed inside LDA measuring volume

    Science.gov (United States)

    Ghosh, Abhijit; Nirala, A. K.

    2016-05-01

    In the present study we propose a technique for micro analysis of fringe field formed inside laser Doppler anemometry (LDA) measuring volume. Detailed knowledge of the fringe field obtained by this technique allows beam quality, alignment and fringe uniformity to be evaluated with greater precision and may be helpful for selection of an appropriate optical element for LDA system operation. A complete characterization of fringes formed at the measurement volume using conventional, as well as holographic optical elements, is presented. Results indicate the qualitative, as well as quantitative, improvement of fringes formed at the measurement volume by holographic optical elements. Hence, use of holographic optical elements in LDA systems may be advantageous for improving accuracy in the measurement.

  18. Volume Measurement in Solid Objects Using Artificial Vision Technique

    Science.gov (United States)

    Cordova-Fraga, T.; Martinez-Espinosa, J. C.; Bernal, J.; Huerta-Franco, R.; Sosa-Aquino, M.; Vargas-Luna, M.

    2004-09-01

    A simple system using artificial vision technique for measuring the volume of solid objects is described. The system is based on the acquisition of an image sequence of the object while it is rotating on an automated mechanism controlled by a PC. Volumes of different objects such as a sphere, a cylinder and also a carrot were measured. The proposed algorithm was developed in environment LabView 6.1. This technique can be very useful when it is applied to measure the human body for evaluating its body composition.

  19. Finding the Density of Objects without Measuring Mass and Volume

    Science.gov (United States)

    Mumba, Frackson; Tsige, Mesfin

    2007-01-01

    A simple method based on the moment of forces and Archimedes' principle is described for finding density without measuring the mass and volume of an object. The method involves balancing two unknown objects of masses M[subscript 1] and M[subscript 2] on each side of a pivot on a metre rule and measuring their corresponding moment arms. The object…

  20. Critical Evaluation of Blood Volume Measurements during Hemodialysis

    NARCIS (Netherlands)

    Dasselaar, Judith J.; van der Sande, Frank M.; Franssen, Casper F. M.

    2012-01-01

    Devices that continuously measure relative blood volume (RBV) changes during hemodialysis (HD) are increasingly used for the prevention of dialysis hypotension and fine-tuning of dry weight. However, RBV measurements are subject to various limitations. First, RBV devices provide information on relat

  1. A liquid-independent volume flow measurement principle

    NARCIS (Netherlands)

    Geers, L.F.G.; Volker, A.W.F.; Hunter, T.P.M.

    2010-01-01

    A novel flow measurement principle is presented enabling non-intrusive volume flow measurements of liquids in the ml/min range. It is based on an opto-acoustical time-of-flight principle, where the time interval is recorded in which a thermal label travels a known distance through a flow channel. Bi

  2. Assessment of control technology for stationary sources. Volume II: control technology data tables. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Minicucci, D.; Herther, M.; Babb, L.; Kuby, W.

    1980-02-01

    This report, the Control Technology Data Tables, is the second volume of the three-volume final report for the contract. It presents in tabular format, qualitative descriptions of control options for the various sources and quantitative information on control technology cost, efficiency, reliability, energy consumption, other environmental impacts and application status. Also included is a code list which classifies the stationary sources examined by industry, process, and emission source.

  3. Measurement and determinants of infrarenal aortic thrombus volume

    Energy Technology Data Exchange (ETDEWEB)

    Golledge, Jonathan; Wolanski, Philippe [James Cook University, The Vascular Biology Unit, Townsville, Queensland (Australia); Townsville Hospital, Townsville, Queensland (Australia); Parr, Adam [James Cook University, The Vascular Biology Unit, Townsville, Queensland (Australia); Buttner, Petra [James Cook University, School of Public Health and Tropical Medicine, Townsville, Queensland (Australia)

    2008-09-15

    Intra-luminal thrombus has been suggested to play a role in the progression of abdominal aortic aneurysm (AAA). The aims of this study were twofold. Firstly, to assess the reproducibility of a computer tomography (CT)-based technique for measurement of aortic thrombus volume. Secondly, to examine the determinants of infrarenal aortic thrombus volume in a cohort of patients with aortic dilatation. A consecutive series of 75 patients assessed by CT angiography with maximum aortic diameter {>=}25 mm were recruited. Intra-luminal thrombus volume was measured by a semi-automated workstation protocol based on a previously defined technique to quantitate aortic calcification. Intra- and inter-observer reproducibility were assessed using correlation coefficients, coefficient of variation and Bland-Altman plots. Infrarenal aortic thrombus volume percentage was related to clinical, anatomical and blood characteristics of the patients using univariate and multivariate tests. Infrarenal aortic thrombus volume was related to the severity of aortic dilatation assessed by total aortic volume (r=0.87, P<0.0001) or maximum aortic diameter (r=0.74, P< 0.0001). We therefore examined the clinical determinates of aortic thrombus expressed as a percentage of total aortic volume. Aortic thrombus percentage was negatively correlated with serum high density lipoprotein (HDL, r=-0.31). By ordinal multiple logistic regression analysis serum HDL below median ({<=}1.2 mM) was associated with aortic thrombus percentage in the upper quartile adjusting for other risk factors (odds ratio 5.3, 95% CI 1.1-25.0). Infrarenal aortic thrombus volume can be measured reproducibly on CT. Serum HDL, which can be therapeutically raised, may play a role in discouraging aortic thrombus accumulation with implications in terms of delaying progression of AAA. (orig.)

  4. Enhancement of H{sup -}/D{sup -} volume production in a double plasma type negative ion source

    Energy Technology Data Exchange (ETDEWEB)

    Fukumasa, Osamu; Nishimura, Hideki; Sakiyama, Satoshi [Yamaguchi Univ., Ube (Japan). Faculty of Engineering

    1997-02-01

    H{sup -}/D{sup -} production in a pure volume source has been studied. In our double plasma type negative ion source, both energy and density of fast electrons are well controlled. With the use of this source, the enhancement of H{sup -}/D{sup -} production has been observed. Namely, under the same discharge power, the extracted H{sup -}/D{sup -} current in the double plasma operation is higher than that in the single plasma operation. At the same time, measurements of plasma parameters have been made in the source and the extractor regions for these two cases. (author)

  5. Reliability of brain volume measurements: a test-retest dataset.

    Science.gov (United States)

    Maclaren, Julian; Han, Zhaoying; Vos, Sjoerd B; Fischbein, Nancy; Bammer, Roland

    2014-01-01

    Evaluation of neurodegenerative disease progression may be assisted by quantification of the volume of structures in the human brain using magnetic resonance imaging (MRI). Automated segmentation software has improved the feasibility of this approach, but often the reliability of measurements is uncertain. We have established a unique dataset to assess the repeatability of brain segmentation and analysis methods. We acquired 120 T1-weighted volumes from 3 subjects (40 volumes/subject) in 20 sessions spanning 31 days, using the protocol recommended by the Alzheimer's Disease Neuroimaging Initiative (ADNI). Each subject was scanned twice within each session, with repositioning between the two scans, allowing determination of test-retest reliability both within a single session (intra-session) and from day to day (inter-session). To demonstrate the application of the dataset, all 3D volumes were processed using FreeSurfer v5.1. The coefficient of variation of volumetric measurements was between 1.6% (caudate) and 6.1% (thalamus). Inter-session variability exceeded intra-session variability for lateral ventricle volume (P<0.0001), indicating that ventricle volume in the subjects varied between days.

  6. The orbital volume measurement in patients with ventriculoperitoneal shunt.

    Science.gov (United States)

    Kim, Jong-Min; Chang, Moo-Hwan; Kyung, Sungeun E

    2015-01-01

    Enophthalmos occurs from the increased bony volume or decreased soft tissue volume in the orbit and can be caused in patients with long-term ventriculoperitoneal (VP) shunt. This study tried to find out the change of orbital volume by measuring the orbital volume before and after operation in adult patients who underwent VP shunt for hydrocephalus. The 2 evaluators measured orbital volume by using ITK-SNAP 2.4 program with double-blind test for computed tomography images before and after operation targeting 36 patients over the age of 18 who underwent VP shunt with pressure-controlled valve from 2003 to 2011. Wilcoxon matched-pairs signed-rank test of GraphPad software was used to statistically analyze the difference in orbital volume change before and after operation. In case of mean pre-op orbital volume of total 36 patients, the right was measured as 23.72 ± 4.65 cm(3), the left as 23.47 ± 4.61 cm(3), the post-op right as 24.67 ± 4.70 cm(3), and the left as 24.18 ± 4.63 cm(3), showing no statistically significant difference (P = 0.106). The mean pre-op orbital volume of 14 people (28 eyes) followed for more than 11 months was 25.06 ± 4.58 cm(3) in the right and 24.4 ± 5.02 cm(3) in the left and the mean post-op orbital volume was 27.0 ± 4.28 cm(3) in the right and 25.76 ± 3.92 cm(3) in the left, showing statistically significant differences in the change of the volume before and after shunt operation (P = 0.0057). In patients who maintain long-term shunt devices after VP shunt, remodeling of matured orbital bone may be caused due to the change in pressure gradient between cranial cavity and orbit and the possible occurrence of resulting secondary enophthalmos by increased orbital volume should be considered.

  7. Comparative technique in measurements of Ge detectors effective volumes

    Science.gov (United States)

    Demidova, E. V.; Kirpichnikov, I. V.; Vasenko, A. A.

    1999-01-01

    A simple and quick procedure was proposed for measurements of large coaxial Ge detectors effective volumes. It included a comparison of background spectra collected with several detectors without any shielding in an underground laboratory. Such measurements were performed in Homestake (USA) and Canfranc (Spain) laboratories with several 1 kg and 2 kg detectors. Monte-Carlo calculations confirmed that ratios of numbers of events in continua of the spectra should be either equal or very close to the ratios of the detectors effective volumes.

  8. Beam formation in CERNs cesiated surfaces and volume H- ion sources

    Science.gov (United States)

    Mochalskyy, Serhiy; Lettry, Jacques; Minea, Tiberiu

    2016-08-01

    At CERN, a high performance negative ion (NI) source is required for the 160 MeV H- linear accelerator named Linac4. The source should deliver 80 mA H- ion beams within an emittance of 0.25 mm·mrad. For this purpose two ion sources were developed: IS01 is based on the NI volume production and IS02 provides additional NI by surface production via H interaction on a cesiated Molybdenum plasma electrode. The development of negative ion sources for Linac4 is accompanied by modelling activities. ONIX code has been modified and adapted to investigate the transport of NI and electrons in the extraction region of the CERN negative ion sources. The simulated results from modeling of IS01 and IS02 extraction regions, which were obtained in 2012 during source commissioning, are presented and benchmarked with experimental measurements obtained after 2013. The formation of the plasma meniscus and the screening of the extraction field by the source plasma are discussed. The NI production is compared between two types of sources, the first one based on volume production only and the second one encompassing NI cesiated surface production. For the IS02 source, different states of conditioning were simulated by changing the NI emission flux from the plasma electrode and Cs+ density in the bulk plasma region. The numerical results show that in low work function regime, with high NI surface emission rate of 3000 A m-2 and Cs-density of nCs+ = 3.8 × 1016 m-3, the total extracted NI current could reach ~80 mA. At the less favorable Cs-coverage, when the surface NI emission rate becomes significantly lower, namely 300 A m-2 with nCs+ = 3.3 × 1015 m-3, the total extracted NI current only reaches ~20 mA. A good agreement between simulation and experimental results is observed in terms of extracted NI current for both extraction systems, including the case of reversed extraction potential that corresponds to positive (H+) ion extraction.

  9. Representative volume element of asphalt pavement for electromagnetic measurements

    Directory of Open Access Journals (Sweden)

    Terhi Pellinen

    2015-02-01

    Full Text Available The motivation for this study was to investigate the representative volume element (RVE needed to correlate the nondestructive electromagnetic (EM measurements with the conventional destructive asphalt pavement quality control measurements. A large pavement rehabilitation contract was used as the test site for the experiment. Pavement cores were drilled from the same locations where the stationary and continuous Ground Penetrating Radar (GPR measurements were obtained. Laboratory measurements included testing the bulk density of cores using two methods, the surface-saturated dry method and determining bulk density by dimensions. Also, Vector Network Analyzer (VNA and the through specimen transmission configuration were employed at microwave frequencies to measure the reference dielectric constant of cores using two different footprint areas and therefore volume elements. The RVE for EM measurements turns out to be frequency dependent; therefore in addition to being dependent on asphalt mixture type and method of obtaining bulk density, it is dependent on the resolution of the EM method used. Then, although the average bulk property results agreed with theoretical formulations of higher core air void content giving a lower dielectric constant, for the individual cores there was no correlation for the VNA measurements because the volume element seizes deviated. Similarly, GPR technique was unable to capture the spatial variation of pavement air voids measured from the 150-mm drill cores. More research is needed to determine the usable RVE for asphalt.

  10. Bioimpedance Measurement of Segmental Fluid Volumes and Hemodynamics

    Science.gov (United States)

    Montgomery, Leslie D.; Wu, Yi-Chang; Ku, Yu-Tsuan E.; Gerth, Wayne A.; DeVincenzi, D. (Technical Monitor)

    2000-01-01

    Bioimpedance has become a useful tool to measure changes in body fluid compartment volumes. An Electrical Impedance Spectroscopic (EIS) system is described that extends the capabilities of conventional fixed frequency impedance plethysmographic (IPG) methods to allow examination of the redistribution of fluids between the intracellular and extracellular compartments of body segments. The combination of EIS and IPG techniques was evaluated in the human calf, thigh, and torso segments of eight healthy men during 90 minutes of six degree head-down tilt (HDT). After 90 minutes HDT the calf and thigh segments significantly (P < 0.05) lost conductive volume (eight and four percent, respectively) while the torso significantly (P < 0.05) gained volume (approximately three percent). Hemodynamic responses calculated from pulsatile IPG data also showed a segmental pattern consistent with vascular fluid loss from the lower extremities and vascular engorgement in the torso. Lumped-parameter equivalent circuit analyses of EIS data for the calf and thigh indicated that the overall volume decreases in these segments arose from reduced extracellular volume that was not completely balanced by increased intracellular volume. The combined use of IPG and EIS techniques enables noninvasive tracking of multi-segment volumetric and hemodynamic responses to environmental and physiological stresses.

  11. Alexandrite laser source for atmospheric lidar measurements

    Science.gov (United States)

    Pelon, J.; Loth, C.; Flamant, P.; Megie, G.

    1986-01-01

    During the past years, there has been a marked increase in interest in the applications of vibronic solid state lasers to meteorology and atmospheric physics. Two airborne lidar programs are now under development in France. The differential absorption lidar (DIAL) method with vibronic solid state lasers is very attractive for water vapor, temperature and pressure measurements. Alexandrite laser and titanium-sapphire are both suitable for these applications. However, only alexandrite rods are commercially available. The requirements on the laser source for airborne dial applications are two fold: (1) a restriction on laser linewidth and a requirement on stability and tunability with a good spectral purity; and (2) a requirement on the time separation between the two pulses. These constraints are summarized.

  12. Reliability and Accuracy of Brain Volume Measurement on MR Imaging

    DEFF Research Database (Denmark)

    Yamagchii, Kechiro; Lassen, Anders; Ring, Poul

    1998-01-01

    Yamaguchi, K., Lassen, A. And Ring, P. Reliability and Accuracy of Brain Volume Measurement on MR Imaging. Abstract at ESMRMB98 European Society for Magnetic Resonance in Medicine and Biology, Geneva, Sept 17-20, 1998 Danish Research Center for Magnetic Resonance, Hvidovre University Hospital...

  13. Determination of air-loop volume and radon partition coefficient for measuring radon in water sample.

    Science.gov (United States)

    Lee, Kil Yong; Burnett, William C

    A simple method for the direct determination of the air-loop volume in a RAD7 system as well as the radon partition coefficient was developed allowing for an accurate measurement of the radon activity in any type of water. The air-loop volume may be measured directly using an external radon source and an empty bottle with a precisely measured volume. The partition coefficient and activity of radon in the water sample may then be determined via the RAD7 using the determined air-loop volume. Activity ratios instead of absolute activities were used to measure the air-loop volume and the radon partition coefficient. In order to verify this approach, we measured the radon partition coefficient in deionized water in the temperature range of 10-30 °C and compared the values to those calculated from the well-known Weigel equation. The results were within 5 % variance throughout the temperature range. We also applied the approach for measurement of the radon partition coefficient in synthetic saline water (0-75 ppt salinity) as well as tap water. The radon activity of the tap water sample was determined by this method as well as the standard RAD-H2O and BigBottle RAD-H2O. The results have shown good agreement between this method and the standard methods.

  14. Gastric residual volume (GRV) and gastric contents measurement by refractometry.

    Science.gov (United States)

    Chang, Wei-Kuo; McClave, Stephen A; Hsieh, Chung-Bao; Chao, You-Chen

    2007-01-01

    Traditional use of gastric residual volumes (GRVs), obtained by aspiration from a nasogastric tube, is inaccurate and cannot differentiate components of the gastric contents (gastric secretion vs delivered formula). The use of refractometry and 3 mathematical equations has been proposed as a method to calculate the formula concentration, GRV, and formula volume. In this paper, we have validated these mathematical equations so that they can be implemented in clinical practice. Each of 16 patients receiving a nasogastric tube had 50 mL of water followed by 100 mL of dietary formula (Osmolite HN, Abbott Laboratories, Columbus, OH) infused into the stomach. After mixing, gastric content was aspirated for the first Brix value (BV) measurement by refractometry. Then, 50 mL of water was infused into the stomach and a second BV was measured. The procedure of infusion of dietary formula (100 mL) and then water (50 mL) was repeated and followed by subsequent BV measurement. The same procedure was performed in an in vitro experiment. Formula concentration, GRV, and formula volume were calculated from the derived mathematical equations. The formula concentrations, GRVs, and formula volumes calculated by using refractometry and the mathematical equations were close to the true values obtained from both in vivo and in vitro validation experiments. Using this method, measurement of the BV of gastric contents is simple, reproducible, and inexpensive. Refractometry and the derived mathematical equations may be used to measure formula concentration, GRV, and formula volume, and also to serve as a tool for monitoring the gastric contents of patients receiving nasogastric feeding.

  15. The 5-Year Outlook on Science and Technology 1981. Source Materials Volume 2.

    Science.gov (United States)

    National Science Foundation, Washington, DC.

    This is the second of two volumes of source documents commissioned by the National Science Foundation in preparing the second 5-Year Outlook on Science and Technology for transmission to the Congress. This volume consists of the views of individuals selected by the Committee on Science, Engineering and Public Policy of the American Association for…

  16. H- ion production in electron cyclotron resonance driven multicusp volume source

    Science.gov (United States)

    Ivanov, A. A.; Rouillé, C.; Bacal, M.; Arnal, Y.; Béchu, S.; Pelletier, J.

    2004-05-01

    We have used the existing magnetic multicusp configuration of the large volume H- source Camembert III to confine the plasma created by seven elementary multidipolar electron cyclotron resonance (ECR) sources, operating at 2.45 GHz. We varied the pressure from 1 to 4 mTorr, while the total power of the microwave generator was varied between 500 W and 1 kW. We studied the plasma created by this system and measured the various plasma parameters, including the density and temperature of the negative hydrogen ions which are compared to the data obtained in a chamber with elementary ECR sources without multicusp magnetic confinement. The electron temperature is lower than that obtained with similar elementary sources in the absence of the magnetic multicusp field. We found that at pressures in the range from 2 to 4 mTorr and microwave power of up to 1 kW, the electron temperature is optimal for H- ion production (0.6-0.8 eV). This could indicate that the multicusp configuration effectively traps the fast electrons produced by the ECR discharge.

  17. The extraction of negative carbon ions from a volume cusp ion source

    Science.gov (United States)

    Melanson, Stephane; Dehnel, Morgan; Potkins, Dave; McDonald, Hamish; Hollinger, Craig; Theroux, Joseph; Martin, Jeff; Stewart, Thomas; Jackle, Philip; Philpott, Chris; Jones, Tobin; Kalvas, Taneli; Tarvainen, Olli

    2017-08-01

    Acetylene and carbon dioxide gases are used in a filament-powered volume-cusp ion source to produce negative carbon ions for the purpose of carbon implantation for gettering applications. The beam was extracted to an energy of 25 keV and the composition was analyzed with a spectrometer system consisting of a 90° dipole magnet and a pair of slits. It is found that acetylene produces mostly C2- ions (up to 92 µA), while carbon dioxide produces mostly O- with only trace amounts of C-. Maximum C2- current was achieved with 400 W of arc power and, the beam current and composition were found to be highly dependent on the pressure in the source. The beam properties as a function of source settings are analyzed, and plasma properties are measured with a Langmuir probe. Finally, we describe testing of a new RF H- ion source, found to produce more than 6 mA of CW H- beam.

  18. Acoustic beam steering by light refraction: illustration with directivity patterns of a tilted volume photoacoustic source.

    Science.gov (United States)

    Raetz, Samuel; Dehoux, Thomas; Perton, Mathieu; Audoin, Bertrand

    2013-12-01

    The symmetry of a thermoelastic source resulting from laser absorption can be broken when the direction of light propagation in an elastic half-space is inclined relatively to the surface. This leads to an asymmetry of the directivity patterns of both compressional and shear acoustic waves. In contrast to classical surface acoustic sources, the tunable volume source allows one to take advantage of the mode conversion at the surface to control the directivity of specific modes. Physical interpretations of the evolution of the directivity patterns with the increasing light angle of incidence and of the relations between the preferential directions of compressional- and shear-wave emission are proposed. In order to compare calculated directivity patterns with measurements of normal displacement amplitudes performed on plates, a procedure is proposed to transform the directivity patterns into pseudo-directivity patterns representative of the experimental conditions. The comparison of the theoretical with measured pseudo-directivity patterns demonstrates the ability to enhance bulk-wave amplitudes and to steer specific bulk acoustic modes by adequately tuning light refraction.

  19. Impact of the Implementation of ESA 2010 on Volume Measurement

    Directory of Open Access Journals (Sweden)

    Petr Musil

    2016-06-01

    Full Text Available Volume indices are connected with statistical deflation that means recalculation of macro-aggregates to constant prices. Price calculations have to follow changes in definition or delineation of macro-aggregates. New standards of National Accounts (SNA 2008, ESA 2010 respectively bring many changes that should be taken into account in volume measures. The aim of this paper is to present new methods of deflation that respekt updated definitions and principles. Concept of foreign trade has been changed significantly as globalization is going faster and faster. Re-export and merchanting have become more important especially in small open economies such as the Czech Republic. This phenomenon should be reflected in constant prices calculations. Changes in methodology have also affected volume indices.

  20. Radiofrequency and 2.45 GHz electron cyclotron resonance H- volume production ion sources

    Science.gov (United States)

    Tarvainen, O.; Peng, S. X.

    2016-10-01

    The volume production of negative hydrogen ions ({{{H}}}-) in plasma ion sources is based on dissociative electron attachment (DEA) to rovibrationally excited hydrogen molecules (H2), which is a two-step process requiring both, hot electrons for ionization, and vibrational excitation of the H2 and cold electrons for the {{{H}}}- formation through DEA. Traditionally {{{H}}}- ion sources relying on the volume production have been tandem-type arc discharge sources equipped with biased filament cathodes sustaining the plasma by thermionic electron emission and with a magnetic filter separating the main discharge from the {{{H}}}- formation volume. The main motivation to develop ion sources based on radiofrequency (RF) or electron cyclotron resonance (ECR) plasma discharges is to eliminate the apparent limitation of the cathode lifetime. In this paper we summarize the principles of {{{H}}}- volume production dictating the ion source design and highlight the differences between the arc discharge and RF/ECR ion sources from both, physics and technology point-of-view. Furthermore, we introduce the state-of-the-art RF and ECR {{{H}}}- volume production ion sources and review the challenges and future prospects of these yet developing technologies.

  1. Measurement of Gallbladder Volume with Ultrasonography in Pregnant Women

    Directory of Open Access Journals (Sweden)

    Sait Kapicioglu

    2000-01-01

    Full Text Available Fasting and postprandial gallbladder volumes were investigated using ultrasonography in three groups (10 subjects in each of healthy women: third trimester pregnant women, postpartum women up to 10 days after giving birth and nonpregnant controls. The scans were performed at 09:00 after a 12 h fast. After the basal measurement was taken, gallbladder volumes were rescanned in 15 min intervals for 60 mins. At the end of this period, all volunteers received a standard liquid test meal, and scans were performed again for 1 h. The mean basal gallbladder volume was 22.2±4.2 mL in the nonpregnant (control group. In the third trimester group, the basal volume was 37.8±10.5 mL – 70.5% higher than in the nonpregnant group (P<0.001. In the postpartum group, the mean basal volume was 37.9% lower (27.4±6.5 mL than that of the third trimester group (P<0.02. This basal volume was 23.6% greater than that of the control group (P<0.05. After administration of a test meal, the postprandial gallbladder volumes decreased during the first few minutes compared with baseline values. The volumes decreased by 10.2% to 39.8% (23.5±7.3 to 34.0±10.2; P<0.01 in the third trimester group, by 14.9% to 43.2% (16.6±4.3 to 23.3±5.5; P<0.01, 0.001 in the postpartum group and by 19.2% to 51.6% (11.9±3.5 to 17.9±3.6; P<0.02, 0.05, 0.01, 0.001 in the control group. Postprandial mean gallbladder volumes of the third trimester (P<0.02 and postpartum groups (P<0.02 to 0.01 were significantly different from those of the control group. In conclusion, incomplete emptying of the gallbladder after eating during the third trimester of pregnancy may contribute to cholesterol-gallstone formation, and pregnancy may thus increase the risk of gallstones.

  2. Study of accurate volume measurement system for plutonium nitrate solution

    Energy Technology Data Exchange (ETDEWEB)

    Hosoma, T. [Power Reactor and Nuclear Fuel Development Corp., Tokai, Ibaraki (Japan). Tokai Works

    1998-12-01

    It is important for effective safeguarding of nuclear materials to establish a technique for accurate volume measurement of plutonium nitrate solution in accountancy tank. The volume of the solution can be estimated by two differential pressures between three dip-tubes, in which the air is purged by an compressor. One of the differential pressure corresponds to the density of the solution, and another corresponds to the surface level of the solution in the tank. The measurement of the differential pressure contains many uncertain errors, such as precision of pressure transducer, fluctuation of back-pressure, generation of bubbles at the front of the dip-tubes, non-uniformity of temperature and density of the solution, pressure drop in the dip-tube, and so on. The various excess pressures at the volume measurement are discussed and corrected by a reasonable method. High precision-differential pressure measurement system is developed with a quartz oscillation type transducer which converts a differential pressure to a digital signal. The developed system is used for inspection by the government and IAEA. (M. Suetake)

  3. CADDIS Volume 2. Sources, Stressors and Responses: Insecticides

    Science.gov (United States)

    Introduction to the insecticides module, when to list insecticides as a candidate cause, ways to measure insecticides, simple and detailed conceptual diagrams for insecticides, insecticides module references and literature reviews.

  4. CADDIS Volume 2. Sources, Stressors and Responses: Nutrients

    Science.gov (United States)

    Introduction to the nutrients module, when to list nutrients as a candidate cause, ways to measure nutrients, simple and detailed conceptual diagrams for nutrients, nutrients module references and literature reviews.

  5. Measurement of cell volume changes by fluorescence self-quenching

    DEFF Research Database (Denmark)

    Hamann, Steffen; Kiilgaard, J.F.; Litman, Thomas

    2002-01-01

    At high concentrations, certain fluorophores undergo self-quenching, i.e., fluorescence intensity decreases with increasing fluorophore concentration. Accordingly, the self-quenching properties can be used for measuring water volume changes in lipid vesicles. In cells, quantitative determination...... of water transport using fluorescence self-quenching has been complicated by the requirement of relatively high (mM) and often toxic loading concentrations. Here we report a simple method that uses low (muM) loading concentrations of calcein-acetoxymethyl ester (calcein-AM) to obtain intracellular...... concentrations of the fluorophore calcein suitable for measurement of changes in cell water volume by self-quenching. The relationship between calcein fluorescence intensity, when excited at 490 nm (its excitation maximum), and calcein concentration was investigated in vitro and in various cultured cell types...

  6. ECR-driven multicusp H^- volume source operated in pulsed or cw mode

    Science.gov (United States)

    Svarnas, Panayiotis

    2005-10-01

    Electron cyclotron resonance (ECR) driven multicusp H^- volume hybrid source [1, 2] operates in continuous (cw) or pulsed microwave (2.45 GHz) mode up to 3 kW. The hydrogen plasma is produced between 1 and 7 mTorr by seven elementary ECR sources housed in the magnetic multipole chamber ``Camembert III'' [3]. This ECR configuration could be applied both to accelerator and fusion ion sources. Negative ion or electron extracted currents and plasma characteristics are studied in both modes with electrical measurements, electrostatic probe and photodetachment. The role of the plasma electrode bias in the values of the extracted currents is major. H^- current is maximized for a bias voltage close to plasma potential. An optimum pressure at 4-5 mTorr yields enhanced H^- density in the center of the chamber, under cw regime. Finally, the post-discharge formation of H^-, in the pulsed mode, is observed. [1] A.A. Ivanov Jr., C. Rouille, M. Bacal, Y. Arnal, S. Bechu, J. Pelletier, Rev. Sci. Instrum. 75(5), 1750 (2004) [2] M. Bacal, A.A. Ivanov Jr., C. Rouille, P. Svarnas, S. Bechu, J. Pelletier, AIP Conf. Proc. No 763 (Kiev, Ukraine) (2004) [3] C. Courteille, A.M. Bruneteau, M. Bacal, Rev. Sci. Instrum. 66(3), 2533 (1995)

  7. Automatic measurement of orbital volume in unilateral coronal synostosis

    DEFF Research Database (Denmark)

    Dahl, Vedrana Andersen; Einarsson, Gudmundur; Darvann, Tron Andre;

    2016-01-01

    Premature fusion of the coronal suture on one side of the calvaria (unilateral coronal synostosis, UCS) results in asymmetric craniofacial development and the deformation of the orbits. Often this necessitates surgery, where CT scanning is employed to obtain measures of the bony orbit...... segmentations. We obtain similar measures, as well as high Dice scores, compared to the experts. The run time for the proposed approach with a prototype implementation is around 3 minutes on a standard laptop, making the method suitable for rapid evaluation of orbital volume in UCS....

  8. A Repetitive Nanosecond Pulse Source for Generation of Large Volume Streamer Discharge

    Institute of Scientific and Technical Information of China (English)

    TAO Fengbo; ZHANG Qiaogen; GAO Bo; WANG Hu; LI Zhou

    2008-01-01

    Using a unipolar pulse with the rise time and the pulse duration in the order of microsecond as the primary pulse,a nanosecond pulse with the repetitive frequency of several kilohertz is generated by a spark gap switch.By varying both the inter-pulse duration and the pulse frequency,the voltage recovery rate of the spark gap switch is investigated at different working conditions such as the gas pressure,the gas composition as well as the bias voltage.The results reveal that either increase in gas pressure or addition of SF6 to the air can increase the voltage recovery rate.The effect of gas composition on the voltage recovery rate is discussed based on the transferring and distribution of the residual space charges.The repetitive nanosecond pulse source is also applied to the generation of large volume,and the discharge currents are measured to investigate the effect of pulse repetition rate on the large volume streamer discharge.

  9. Laser-induced incandescence: Towards quantitative soot volume fraction measurements

    Energy Technology Data Exchange (ETDEWEB)

    Tzannis, A.P.; Wienbeucker, F.; Beaud, P.; Frey, H.-M.; Gerber, T.; Mischler, B.; Radi, P.P. [Paul Scherrer Inst. (PSI), Villigen (Switzerland)

    1999-08-01

    Laser-Induced Incandescence has recently emerged as a versatile tool for measuring soot volume fraction in a wide range of combustion systems. In this work we investigate the essential features of the method. LII is based on the acquisition of the incandescence of soot when heated through a high power laser pulse. Initial experiments have been performed on a model laboratory flame. The behaviour of the LII signal is studied experimentally. By applying numerical calculations we investigate the possibility to obtain two-dimensional soot volume fraction distributions. For this purpose a combination of LII with other techniques is required. This part is discussed in some extent and the future work is outlined. (author) 4 figs., 3 refs.

  10. Gamma ray densitometry techniques for measuring of volume fractions

    Energy Technology Data Exchange (ETDEWEB)

    Affonso, Renato Raoni Werneck; Silva, Ademir Xavier da; Salgado, Cesar Marques, E-mail: raoniwa@yahoo.com.br, E-mail: ademir@nuclear.ufrj.br, E-mail: otero@ien.gov.br [Instituto de Engenharia Nuclear (IEN/CNEN-RJ), Rio de Janeiro, RJ (Brazil)

    2015-07-01

    Knowledge of the volume fraction in a multiphase flow is of key importance in predicting the performance of many systems and processes. It is therefore an important parameter to characterize such flows. In the context of nuclear techniques, the gamma ray densitometry is promising and this is due to its non-invasive characteristics and very reliable results. It is used in several applications for multiphase flows (water-oil-air), which are employed tools such as: computational fluid dynamics, artificial neural networks and statistical methods of radiation transport, such as the Monte Carlo method. Based on the gamma radiation techniques for measurements of volume fractions, the aim of this paper is to present several techniques developed for this purpose. (author)

  11. Measurement and analysis of grain boundary grooving by volume diffusion

    Science.gov (United States)

    Hardy, S. C.; Mcfadden, G. B.; Coriell, S. R.; Voorhees, P. W.; Sekerka, R. F.

    1991-01-01

    Experimental measurements of isothermal grain boundary grooving by volume diffusion are carried out for Sn bicrystals in the Sn-Pb system near the eutectic temperature. The dimensions of the groove increase with a temporal exponent of 1/3, and measurement of the associated rate constant allows the determination of the product of the liquid diffusion coefficient D and the capillarity length Gamma associated with the interfacial free energy of the crystal-melt interface. The small-slope theory of Mullins is generalized to the entire range of dihedral angles by using a boundary integral formulation of the associated free boundary problem, and excellent agreement with experimental groove shapes is obtained. By using the diffusivity measured by Jordon and Hunt, the present measured values of Gamma are found to agree to within 5 percent with the values obtained from experiments by Gunduz and Hunt on grain boundary grooving in a temperature gradient.

  12. The influence of urine volume on body impedance measurement.

    Science.gov (United States)

    Hong, K H; Park, K S

    2008-01-01

    Bio-signal has some characteristics that the signal is so weak. So, it is good that the factors to influence measured electrical signal are eliminated as much as they can. So, in this paper we will show the influence of urine in bladder on measuring human body impedance. Human urine has different conductivity from other human tissues. Therefore, if the volume of the urine changed, the measured body impedance data also changed.So, in this paper, we will show the influence of urine in bladder with foot-to-foot and thigh-to-thigh current paths. As a result, if the current flows through human bladder, the influence of urine in the bladder must be considered when the body impedance is measured

  13. Multibeam volume acoustic backscatter imagery and reverberation measurements in the northeastern Gulf of Mexico

    Science.gov (United States)

    Gallaudet, Timothy C.; deMoustier, Christian P.

    2002-08-01

    Multibeam volume acoustic backscatter imagery and reverberation measurements are derived from data collected in 200-m-deep waters in the northeastern Gulf of Mexico, with the Toroidal Volume Search Sonar (TVSS), a 68-kHz cylindrical sonar operated by the U.S. Navy's Coastal System Station. The TVSS's 360-degree vertical imaging plane allows simultaneous identification of multiple volume scattering sources and their discrimination from backscatter at the sea surface or the seafloor. This imaging capability is used to construct a three-dimensional representation of a pelagic fish school near the bottom. Scattering layers imaged in the mixed layer and upper thermocline are attributed to assemblages of epipelagic zooplankton. The fine scale patchiness of these scatterers is assessed with the two-dimensional variance spectra of vertical volume scattering strength images in the upper and middle water column. Mean volume reverberation levels exhibit a vertical directionality which is attributed to the volume scattering layers. Boundary echo sidelobe interference and reverberation is shown to be the major limitation in obtaining bioacoustic data with the TVSS. Because net tow and trawl samples were not collected with the acoustic data, the analysis presented is based upon comparison to previous biologic surveys in the northeastern Gulf of Mexico and reference to the bioacoustic literature. copyright 2002 Acoustical Society of America.

  14. Online blind source separation using incremental nonnegative matrix factorization with volume constraint.

    Science.gov (United States)

    Zhou, Guoxu; Yang, Zuyuan; Xie, Shengli; Yang, Jun-Mei

    2011-04-01

    Online blind source separation (BSS) is proposed to overcome the high computational cost problem, which limits the practical applications of traditional batch BSS algorithms. However, the existing online BSS methods are mainly used to separate independent or uncorrelated sources. Recently, nonnegative matrix factorization (NMF) shows great potential to separate the correlative sources, where some constraints are often imposed to overcome the non-uniqueness of the factorization. In this paper, an incremental NMF with volume constraint is derived and utilized for solving online BSS. The volume constraint to the mixing matrix enhances the identifiability of the sources, while the incremental learning mode reduces the computational cost. The proposed method takes advantage of the natural gradient based multiplication updating rule, and it performs especially well in the recovery of dependent sources. Simulations in BSS for dual-energy X-ray images, online encrypted speech signals, and high correlative face images show the validity of the proposed method.

  15. Source preparations for alpha and beta measurements

    Energy Technology Data Exchange (ETDEWEB)

    Holm, E. [Risoe National Lab., Roskilde (Denmark)

    2001-01-01

    Regarding alpha particle emitters subject for environmental studies, electrodeposition or co-precipitation as fluorides are the most common methods. For electro deposition stainless steel is generally used as cathode material but also other metals such as Ni, Ag, and Cu showed promising results. The use of other anode material than platinum, such as graphite should be investigated. For other purposes such as optimal resolution other more sophisticated methods are used but often resulting in poorer recovery. For beta particle emitters the type of detection system will decide the source preparation. Similar methods as for alpha particle emitters, electrodeposition or precipitation techniques can be used. Due to the continuous energy distribution of the beta pulse height distribution a high resolution is not required. Thicker sources from the precipitates or a stable isotopic carrier can be accepted but correction for absorption in the source must be done. (au)

  16. Noninvasive Intracranial Volume and Pressure Measurements Using Ultrasound

    Science.gov (United States)

    Hargens, A. R.

    1998-01-01

    Prevention of secondary brain injuries following head can be accomplished most easily when intracranial pressure (ICP) is monitored. However, current measurement techniques are invasive and thus not practical in the combat environment. The Pulsed Phase Lock Loop (PPLL) devise, which was developed and patented, uses a unique, noninvasive ultrasonic phase comparison method to measure slight changes in cranial volume which occur with changes in ICP. Year one studies involved instrument improvements and measurement of altered intracranial distance with altered ICP in fresh cadavera. Our software was improved to facilitate future studies of normal subjects and trauma patients. Our bench studies proved that PPLL output correlated highly with changes in path length across a model cranium. Cadaveric studies demonstrated excellent compact, noninvasive devise for monitoring changes in intracranial distance may aid in the early detection of elevated ICP, decreasing risk of secondary brain injury and infection, and returning head-injured patients to duty.

  17. Ion beam measurements at the superconducting ECR ion source SECRAL

    Energy Technology Data Exchange (ETDEWEB)

    Maeder, Jan; Rossbach, Jon; Lang, Ralf; Maimone, Fabio; Spaedtke, Peter; Tinschert, Klaus [Gesellschaft fuer Schwerionenforschung mbH, Darmstadt (Germany); Sun, Liangting; Cao, Yun; Zhao, Hongwei [Institute of Modern Physics, Lanzhou, GS (China)

    2009-08-15

    Measurement of the charge-state distribution, the beam profile, the beam emittance of the named ion source are presented. Furthermore computer simulations of the magnetic flux-density distribution in this source are described. (HSI)

  18. Measurements of the volume scattering function in a coastal environment

    Science.gov (United States)

    Berthon, Jean-François; Lee, Michael; Shybanov, Eugeny; Zibordi, Giuseppe

    2007-04-01

    The Volume Scattering Function (VSF) is an essential variable in the context of marine radiative transfer modeling and of the inversion of ocean colour remote sensing data. However, an important lack of knowledge on the VSF natural variability affects the present models, in particular for the coastal environment. Measurements of the Volume Scattering Function between 0.6° and 177.3° with an angular resolution of 0.3° were performed in the northern coastal Adriatic Sea onboard an oceanographic platform in October 2004 using a prototype instrument. Observed differences with the commonly used Petzold's functions are significant, in particular for the "open ocean" and "coastal" types in the backward directions. The use of an empirical relationship for the derivation of b b(λ) from a unique measurement of β(ψ,λ) at ψ=140 for the Hydroscat-6 was validated for this coastal site at that season. Finally, the use of the Kopelevich VSF model together with a measurement of b p(λ) at λ=555 nm allowed the reconstruction of the VSF to within about 35%.

  19. Integrated Optofluidic Chip for Low-Volume Fluid Viscosity Measurement

    Directory of Open Access Journals (Sweden)

    Tie Yang

    2017-02-01

    Full Text Available In the present work, an integrated optofluidic chip for fluid viscosity measurements in the range from 1 mPa·s to 100 mPa·s is proposed. The device allows the use of small sample volumes (<1 µL and the measurement of viscosity as a function of temperature. Thanks to the precise control of the force exerted on dielectric spheres by optical beams, the viscosity of fluids is assessed by comparing the experimentally observed movement of dielectric beads produced by the optical forces with that expected by numerical calculations. The chip and the developed technique are validated by analyzing several fluids, such as Milli-Q water, ethanol and water–glycerol mixtures. The results show a good agreement between the experimental values and those reported in the literature. The extremely reduced volume of the sample required and the high flexibility of this technique make it a good candidate for measuring a wide range of viscosity values as well as for the analysis of nonlinear viscosity in complex fluids.

  20. High-speed volume measurement system and method

    Science.gov (United States)

    Lane, Michael H.; Doyle, Jr., James L.; Brinkman, Michael J.

    2015-11-24

    Disclosed is a volume sensor having first, second, and third laser sources emitting first, second, and third laser beams; first, second, and third beam splitters splitting the first, second, and third laser beams into first, second, and third beam pairs; first, second, and third optical assemblies expanding the first, second, and third beam pairs into first, second, and third pairs of parallel beam sheets; fourth, fifth, and sixth optical assemblies focusing the first, second, and third beam sheet pairs into fourth, fifth, and sixth beam pairs; and first, second, and third detector pairs receiving the fourth, fifth, and sixth beam pairs and converting a change in intensity of at least one of the beam pairs resulting from an object passing through at least one of the first, second, and third parallel beam sheets into at least one electrical signal proportional to a three-dimensional representation of the object.

  1. Assessment of control technology for stationary sources. Volume I: technical discussion. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Minicucci, D.; Herther, M.; Babb, L.; Kuby, W.

    1980-02-01

    The purpose of this project was to develop a reference document for use by the Air Resources Board, local air pollution control districts, and the U.S. Environmental Protection Agency that describes technological options available for the control of emissions from stationary sources located in California. Control technologies were examined for 10 industry groups and six air pollutants. Volume I, Technical Discussion, includes an overall introduction to the project, descriptions of its major elements, background information for each industry group addressed, and the project bibliography. In Volume II, Control Technology Data Tables, qualitative descriptions of control options for the various sources and quantitative information on control technology cost, efficiency, reliability, energy consumption, other environmental impacts, and application status are presented in tabular format. Also included is a code list that classifies the stationary sources examined by industry, process and emission source.

  2. Evaluation of right ventricular volumes measured by magnetic resonance imaging

    DEFF Research Database (Denmark)

    Møgelvang, J; Stubgaard, M; Thomsen, C

    1988-01-01

    Right ventricular volumes were determined in 12 patients with different levels of right and left ventricular function by magnetic resonance imaging (MRI) using an ECG gated multisection technique in planes perpendicular to the diastolic position of the interventricular septum. Right ventricular...... stroke volume was calculated as the difference between end-diastolic and end-systolic volume and compared to left ventricular stroke volume and to stroke volume determined simultaneously by a classical indicator dilution technique. There was good agreement between right ventricular stroke volume...... determined by MRI and by the indicator dilution method and between right and left ventricular stroke volume determined by MRI. Thus, MRI gives reliable values not only for left ventricular volumes, but also for right ventricular volumes. By MRI it is possible to obtain volumes from both ventricles...

  3. Measurement of atmospheric neutrino oscillations with very large volume neutrino telescopes

    CERN Document Server

    Yañez, J P

    2015-01-01

    Neutrino oscillations have been probed during the last few decades using multiple neutrino sources and experimental set-ups. In the recent years, very large volume neutrino telescopes have started contributing to the field. First ANTARES and then IceCube have relied on large and sparsely instrumented volumes to observe atmospheric neutrinos for combinations of baselines and energies inaccessible to other experiments. Using this advantage, the latest result from IceCube starts approaching the precision of other established technologies, and is paving the way for future detectors, such as ORCA and PINGU. These new projects seek to provide better measurements of neutrino oscillation parameters, and eventually determine the neutrino mass ordering. The results from running experiments and the potential from proposed projects are discussed in this review, emphasizing the experimental challenges involved in the measurements.

  4. Measurement of Atmospheric Neutrino Oscillations with Very Large Volume Neutrino Telescopes

    Directory of Open Access Journals (Sweden)

    J. P. Yáñez

    2015-01-01

    Full Text Available Neutrino oscillations have been probed during the last few decades using multiple neutrino sources and experimental set-ups. In the recent years, very large volume neutrino telescopes have started contributing to the field. First ANTARES and then IceCube have relied on large and sparsely instrumented volumes to observe atmospheric neutrinos for combinations of baselines and energies inaccessible to other experiments. Using this advantage, the latest result from IceCube starts approaching the precision of other established technologies and is paving the way for future detectors, such as ORCA and PINGU. These new projects seek to provide better measurements of neutrino oscillation parameters and eventually determine the neutrino mass ordering. The results from running experiments and the potential from proposed projects are discussed in this review, emphasizing the experimental challenges involved in the measurements.

  5. Evaluation of Sources of Uncertainties in Solar Resource Measurement

    Energy Technology Data Exchange (ETDEWEB)

    Habte, Aron M [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Sengupta, Manajit [National Renewable Energy Laboratory (NREL), Golden, CO (United States)

    2017-09-25

    This poster presents a high-level overview of sources of uncertainties in solar resource measurement, demonstrating the impact of various sources of uncertainties -- such as cosine response, thermal offset, spectral response, and others -- on the accuracy of data from several radiometers. The study provides insight on how to reduce the impact of some of the sources of uncertainties.

  6. PM10 source measurement methodology: Field studies

    Energy Technology Data Exchange (ETDEWEB)

    Farthing, W.E.; Martin, R.S.; Dawes, S.S.; Williamson, A.D.

    1989-05-01

    Two candidate measurement methods, Constant Sampling Rate (CSR) and Exhaust Gas Recycle (EGR), have been developed to measure emissions of in-stack PM-10 particulate matter with aerodynamic diameter less than 10 micrometers. Two field tests were performed at the clinker cooler exhaust of a Portland cement plant to quantify precision and comparability of these techniques. In addition, accuracy was determined for total particulate measurement by comparison to Method 17. Collocated sampling trains were operated parallel with two Method 17 trains. In the second test, two CSR and one EGR trains were operated parallel to two Method 17 trains. The operating procedures used for the CSR and EGR trains are described in detail. In measurement of PM-10 and total particulate matter, the precision of both the CSR and EGR techniques was found to be of the same magnitude as Method 17 (approximately 5%). A small bias was found between CSR and EGR PM-10 results (15%) and between EGR and Method 17 total particulate matter (10%). Although small, these observed differences, combined with the results of laboratory studies reported elsewhere, led to a recommendation for an increase in the length of sampling nozzles. This modification improved cyclone performance and is incorporated into the nozzle geometries described in the application guides for CSR and EGR.

  7. Studies on plasma production in a large volume system using multiple compact ECR plasma sources

    Science.gov (United States)

    Tarey, R. D.; Ganguli, A.; Sahu, D.; Narayanan, R.; Arora, N.

    2017-01-01

    This paper presents a scheme for large volume plasma production using multiple highly portable compact ECR plasma sources (CEPS) (Ganguli et al 2016 Plasma Source Sci. Technol. 25 025026). The large volume plasma system (LVPS) described in the paper is a scalable, cylindrical vessel of diameter  ≈1 m, consisting of source and spacer sections with multiple CEPS mounted symmetrically on the periphery of the source sections. Scaling is achieved by altering the number of source sections/the number of sources in a source section or changing the number of spacer sections for adjusting the spacing between the source sections. A series of plasma characterization experiments using argon gas were conducted on the LVPS under different configurations of CEPS, source and spacer sections, for an operating pressure in the range 0.5-20 mTorr, and a microwave power level in the range 400-500 W per source. Using Langmuir probes (LP), it was possible to show that the plasma density (~1  -  2  ×  1011 cm-3) remains fairly uniform inside the system and decreases marginally close to the chamber wall, and this uniformity increases with an increase in the number of sources. It was seen that a warm electron population (60-80 eV) is always present and is about 0.1% of the bulk plasma density. The mechanism of plasma production is discussed in light of the results obtained for a single CEPS (Ganguli et al 2016 Plasma Source Sci. Technol. 25 025026).

  8. Sex Assessment from the Volume of the First Metatarsal Bone: A Comparison of Linear and Volume Measurements.

    Science.gov (United States)

    Gibelli, Daniele; Poppa, Pasquale; Cummaudo, Marco; Mattia, Mirko; Cappella, Annalisa; Mazzarelli, Debora; Zago, Matteo; Sforza, Chiarella; Cattaneo, Cristina

    2017-02-23

    Sexual dimorphism is a crucial characteristic of skeleton. In the last years, volumetric and surface 3D acquisition systems have enabled anthropologists to assess surfaces and volumes, whose potential still needs to be verified. This article aimed at assessing volume and linear parameters of the first metatarsal bone through 3D acquisition by laser scanning. Sixty-eight skeletons underwent 3D scan through laser scanner: Seven linear measurements and volume from each bone were assessed. A cutoff value of 13,370 mm(3) was found, with an accuracy of 80.8%. Linear measurements outperformed volume: metatarsal length and mediolateral width of base showed higher cross-validated accuracies (respectively, 82.1% and 79.1%, raising at 83.6% when both of them were included). Further studies are needed to verify the real advantage for sex assessment provided by volume measurements. © 2017 American Academy of Forensic Sciences.

  9. Self-heating probe instrument and method for measuring high temperature melting volume change rate of material

    Science.gov (United States)

    Wang, Junwei; Wang, Zhiping; Lu, Yang; Cheng, Bo

    2013-03-01

    The castings defects are affected by the melting volume change rate of material. The change rate has an important effect on running safety of the high temperature thermal storage chamber, too. But the characteristics of existing measuring installations are complex structure, troublesome operation and low precision. In order to measure the melting volume change rate of material accurately and conveniently, a self-designed measuring instrument, self-heating probe instrument, and measuring method are described. Temperature in heating cavity is controlled by PID temperature controller; melting volume change rate υ and molten density are calculated based on the melt volume which is measured by the instrument. Positive and negative υ represent expansion and shrinkage of the sample volume after melting, respectively. Taking eutectic LiF+CaF2 for example, its melting volume change rate and melting density at 1 123 K are -20.6% and 2 651 kg·m-3 measured by this instrument, which is only 0.71% smaller than literature value. Density and melting volume change rate of industry pure aluminum at 973 K and analysis pure NaCl at 1 123 K are detected by the instrument too. The measure results are agreed with report values. Measuring error sources are analyzed and several improving measures are proposed. In theory, the measuring errors of the change rate and molten density which are measured by the self-designed instrument is nearly 1/20-1/50 of that measured by the refitted mandril thermal expansion instrument. The self-designed instrument and method have the advantages of simple structure, being easy to operate, extensive applicability for material, relatively high accuracy, and most importantly, temperature and sample vapor pressure have little effect on the measurement accuracy. The presented instrument and method solve the problems of complicated structure and procedures, and large measuring errors for the samples with high vapor pressure by existing installations.

  10. Measurement of negative ion density in a pulsed multicusp negative ion source

    Energy Technology Data Exchange (ETDEWEB)

    Coonan, B.; Mellon, K.N.; Hopkins, M.B. (Dublin City University, Dublin (Ireland))

    1992-10-05

    The production of negative ion beams for use in neutral beam injection heating has become an important area of research in recent years. This paper discusses the negative ion densities measured in a pulsed multicusp volume ion source using photodetachment diagnostic technique. A pulse modulated negative ion source is being used as an alternative to the tandem source and an increase in negative ion extracted current has previously been observed by Hopkins and Mellon. Work with photodetachment quoted in this paper shows an increase in negative ion density during the post discharge similar to previous results obtained using an accelerator to extract the negative ions.

  11. Characteristics of the negative ion beam extracted from an LBL multicusp volume source

    Energy Technology Data Exchange (ETDEWEB)

    Debiak, T.W.; Solensten, L.; Sredniawski, J.J.; Ng, Y.C.; Heuer, R. (Grumman Corporation, Bethpage, New York 11714 (US))

    1990-01-01

    This work encompasses a study of the beam position, profile, and emittance of a Lawrence Berkeley Lab (LBL) multicusp volume source. The study includes a comparison of different extraction geometries with single- and multiple-hole apertures. Our work is currently based on single-gap extraction and acceleration. These experiments are the first of a planned series of studies with various extractor geometries. The beam profile full width at half-maximum ranged from 5.7 to 10.2 mm at a position 69 mm from the emission aperture. Measurements of profile and position in the vertical direction indicate that the beam is significantly bent in the direction expected due to the field of the electron separation magnet. Phase space contour plots in the horizontal plane have been obtained for circular extraction apertures with a diameter of 1.0 and 2.0 mm, and a multiple-hole aperture with an overall diameter of 2.46 mm. Emittances were calculated to be as low as 0.0010 {pi} cm mrad for the 1-mm aperture and 0.0014 {pi} cm mrad for the 2-mm aperture. Emittances are not reported for the multiple-hole aperture due to the shape of the phase space contours; however, analysis of the data is in progress to provide a meaningful comparison of the single-hole and multiple-hole beam characteristics.

  12. Quantitation of mandibular symphysis volume as a source of bone grafting.

    Science.gov (United States)

    Verdugo, Fernando; Simonian, Krikor; Smith McDonald, Roberto; Nowzari, Hessam

    2010-06-01

    Autogenous intramembranous bone graft present several advantages such as minimal resorption and high concentration of bone morphogenetic proteins. A method for measuring the amount of bone that can be harvested from the symphysis area has not been reported in real patients. The aim of the present study was to intrasurgically quantitate the volume of the symphysis bone graft that can be safely harvested in live patients and compare it with AutoCAD (version 16.0, Autodesk, Inc., San Rafael, CA, USA) tomographic calculations. AutoCAD software program quantitated symphysis bone graft in 40 patients using computerized tomographies. Direct intrasurgical measurements were recorded thereafter and compared with AutoCAD data. The bone volume was measured at the recipient sites of a subgroup of 10 patients, 6 months post sinus augmentation. The volume of bone graft measured by AutoCAD averaged 1.4 mL (SD 0.6 mL, range: 0.5-2.7 mL). The volume of bone graft measured intrasurgically averaged 2.3 mL (SD 0.4 mL, range 1.7-2.8 mL). The statistical difference between the two measurement methods was significant. The bone volume measured at the recipient sites 6 months post sinus augmentation averaged 1.9 mL (SD 0.3 mL, range 1.3-2.6 mL) with a mean loss of 0.4 mL. AutoCAD did not overestimate the volume of bone that can be safely harvested from the mandibular symphysis. The use of the design software program may improve surgical treatment planning prior to sinus augmentation.

  13. Rebuilding sources of linear tracers after atmospheric concentration measurements

    Directory of Open Access Journals (Sweden)

    J.-P. Issartel

    2003-01-01

    Full Text Available The identification of widespread sources of passive tracers out of atmospheric concentration measurements has become an important challenge of modern meteorology. The paper proposes some mathematical tracks to address the reconstruction of the complex space-time geometry of the sources of linear tracers. The methods are based upon the use of retroplumes. The inverse problem is addressed in a deterministic non statistical frame. The information obtained by local measurements is spread by introducing the concept of illumination. The constraint that the source is non negative is also addressed. The experimental source ETEX1 is rebuilt in order to evaluate an impulse response of the algorithms.

  14. Source-based morphometry reveals distinct patterns of aberrant brain volume in delusional infestation.

    Science.gov (United States)

    Wolf, Robert Ch; Huber, Markus; Lepping, Peter; Sambataro, Fabio; Depping, Malte S; Karner, Martin; Freudenmann, Roland W

    2014-01-03

    Little is known about the neural correlates of delusional infestation (DI), the delusional belief to be infested with pathogens. So far, evidence comes mainly from case reports and case series. We investigated brain morphology in 16 DI patients and 16 healthy controls using structural magnetic resonance imaging and a multivariate data analysis technique, i.e. source-based morphometry (SBM). In addition, we explored differences in brain structure in patient subgroups based on disease aetiology. SBM revealed two patterns exhibiting significantly (pdisorder) and "organic" DI (DI due to a medical condition). In contrast, aberrant white matter volume was only confirmed for the "organic" DI patient subgroup. These results suggest prefrontal, temporal, parietal, insular, thalamic and striatal dysfunction underlying DI. Moreover, the data suggest that aetiologically distinct presentations of DI share similar patterns of abnormal grey matter volume, whereas aberrant white matter volume appears to be restricted to organic cases. © 2013.

  15. High-frequency radio polarization measurements of WMAP point sources

    CERN Document Server

    Jackson, N; Battye, R A; Gabuzda, D; Taylor, A C

    2009-01-01

    We present polarization measurements at 8.4, 22, and 43 GHz made with the VLA of a complete sample of extragalactic sources stronger than 1 Jy in the 5-year WMAP catalogue and with declinations north of -34 degrees. The observations were motivated by the need to know the polarization properties of radio sources at frequencies of tens of GHz in order to subtract polarized foregrounds for future sensitive Cosmic Microwave Background (CMB) experiments. The total intensity and polarization measurements are generally consistent with comparable VLA calibration measurements for less-variable sources, and within a similar range to WMAP fluxes for unresolved sources. A further paper will present correlations between measured parameters and derive implications for CMB measurements.

  16. The enhanced volume source boundary point method for the calculation of acoustic radiation problem

    Institute of Scientific and Technical Information of China (English)

    WANG Xiufeng; CHEN Xinzhao; WANG Youcheng

    2003-01-01

    The Volume Source Boundary Point Method (VSBPM) is greatly improved so that it will speed up the VSBPM's solution of the acoustic radiation problem caused by the vibrating body. The fundamental solution provided by Helmholtz equation is enforced in a weighted residual sense over a tetrahedron located on the normal line of the boundary node to replace the coefficient matrices of the system equation. Through the enhanced volume source boundary point analysis of various examples and the sound field of a vibrating rectangular box in a semi-anechoic chamber, it has revealed that the calculating speed of the EVSBPM is more than 10 times faster than that of the VSBPM while it works on the aspects of its calculating precision and stability, adaptation to geometric shape of vibrating body as well as its ability to overcome the non-uniqueness problem.

  17. Characterization of volume type ion source for $p$, $H_2^+$ and $H_3^+$ beams

    CERN Document Server

    Joshi, N; Meusel, O; Ratzinger, U

    2016-01-01

    Recently, there is an increasing need for $H_{2}^+$ and $H_{3}^+$ ion sources. One example are ion therapy facilities, where $C^{4+}$ and $H_{3}^+$ ion beams along the linac are of great interest. Another example is a $H_{2}^+$ test beam for linacs finally operated with intense deuteron beams. At Frankfurt, a simple proton ion source is needed to test a new kind of beam injection into a magnetic storage ring\\cite{EPAC08}\\cite{EPAC06}. This article describes a volume type ion source which can deliver upto $3.05~mA$ beam current at $10~keV$ in stable dc operation. It is a hot filament driven ion source which can provide high fractions of $p$, $H_{2}^+$ or $H_{3}^+$, depending on the operation settings.

  18. HTGR accident initiation and progression analysis status report. Volume V. AIPA fission product source terms

    Energy Technology Data Exchange (ETDEWEB)

    Alberstein, D.; Apperson, C.E. Jr.; Hanson, D.L.; Myers, B.F.; Pfeiffer, W.W.

    1976-02-01

    The primary objective of the Accident Initiation and Progression Analysis (AIPA) Program is to provide guidance for high-temperature gas-cooled reactor (HTGR) safety research and development. Among the parameters considered in estimating the uncertainties in site boundary doses are uncertainties in fission product source terms generated under normal operating conditions, i.e., fuel body inventories, circulating coolant activity, total plateout activity in the primary circuit, and plateout distributions. The volume presented documents the analyses of these source term uncertainties. The results are used for the detailed consequence evaluations, and they provide the basis for evaluation of fission products important for HTGR maintenance and shielding.

  19. Advanced energy sources and conversion techniques. Proceedings of a seminar. Volume 1. [35 papers

    Energy Technology Data Exchange (ETDEWEB)

    None

    1958-11-01

    The Seminar was organized as a series of tutorial presentations and round table discussions on a technical level to implement the following: (a) to identify and explore present and projected needs for energy sources and conversion techniques for military applications; (b) to exchange information on current and planned efforts in these fields; (c) to examine the effect of anticipated scientific and technological advances on these efforts; and (d) to present suggested programs aimed at satisfying the military needs for energy sources and conversion techniques. Volume I contains all of the unclassified papers presented at the Seminar. (W.D.M.)

  20. Volume measurement of the leg with the depth camera for quantitative evaluation of edema

    Science.gov (United States)

    Kiyomitsu, Kaoru; Kakinuma, Akihiro; Takahashi, Hiroshi; Kamijo, Naohiro; Ogawa, Keiko; Tsumura, Norimichi

    2017-02-01

    Volume measurement of the leg is important in the evaluation of leg edema. Recently, method for measurement by using a depth camera is proposed. However, many depth cameras are expensive. Therefore, we propose a method using Microsoft Kinect. We obtain a point cloud of the leg by Kinect Fusion technique and calculate the volume. We measured the volume of leg for three healthy students during three days. In each measurement, the increase of volume was confirmed from morning to evening. It is known that the volume of leg is increased in doing office work. Our experimental results meet this expectation.

  1. Volume-scalable high-brightness three-dimensional visible light source

    Science.gov (United States)

    Subramania, Ganapathi; Fischer, Arthur J; Wang, George T; Li, Qiming

    2014-02-18

    A volume-scalable, high-brightness, electrically driven visible light source comprises a three-dimensional photonic crystal (3DPC) comprising one or more direct bandgap semiconductors. The improved light emission performance of the invention is achieved based on the enhancement of radiative emission of light emitters placed inside a 3DPC due to the strong modification of the photonic density-of-states engendered by the 3DPC.

  2. The mechanical measuring method of welding heat source efficiency

    Institute of Scientific and Technical Information of China (English)

    Zhang Jianqiang; Zhang Guodong; He Jie; Wang Chengquan; Chen Bingquan

    2007-01-01

    Based on the principle of residual deformation induced by superposition of the welding residual stress and working stress, the welding heat source efficiency has been determined by measuring displacement changes of specimens under loading and unloading in tensile tests, and combining with calculating welding parameters. Meanwhile, the welding heat source efficiencies obtained are compared with those of the measuring-calculating method. The research results show that the welding heat source efficiencies are almost the same as those obtained by the measuring-calculating method. Therefore, the welding heat source efficiency can be determined accurately by this method, and a new determining method of the heat source efficiency for the welding heat process calculating has been provided.

  3. Application research of tune measurement system in Hefei light source

    CERN Document Server

    Sun Bao Gen; Xu Hong Liang; Lu Ping; Wang Jun; Gao Yun Feng; Wang Li; LiuJinYing

    2002-01-01

    The author introduces the measurement and research of some beam parameters using tune measurement system for Hefei Light Source (HLS), which include the betatron tune, beta function, natural chromaticity, corrected chromaticity, and central frequency. Additionally, it also describes the measurement of the influence of DC clearing electrodes on the betatron tune shift and gives some measurement results. The measurement results are compared with the theoretical values and they are in good agreement

  4. The calorimetric measurement of low energy brachytherapy sources

    Science.gov (United States)

    Aus, Robert John

    Historically, the dose rate to tissue from 125I and 103Pd sources was based on a source's apparent activity in free space. The American Association of Physicists in Medicine Task Group 43 (TG43) established a protocol that clarified this formalism for the dose rate determination that was universally accepted in the Medical Physics community. The TG43 protocol is based on air kerma strength and a different set of conversion factors for determining the dose rate. However, there are still many uncertainties associated with this methodology. These uncertainties are predominantly the result of the unknown effects of variations in the source encapsulation and internal source structure on the dose distribution surrounding a source. Currently, there is no method of nondestructively determining the contained radioactivity of brachytherapy sources. Without the knowledge of the contained activity, the effects of source construction variations cannot be evaluated accurately. The goal of this work was to develop a calorimeter that measures the total power generated by a source. This information could then be used to nondestructively determine the contained radioactivity activity of a source. The power generated by three different, well characterized source designs of 125I brachytherapy seeds was measured with the calorimeter. A theoretical model of the calorimeter was also developed to demonstrate that the calorimeter operated as expected. The measured and theoretical temperature results for the three different source models were consistent within the uncertainty of the measurements. The consistency between the calorimetric measurements and the theoretical expected results demonstrates proof of principle of the calorimeter. The information determined from the model can also be useful for future calorimetric research by identifying required calorimeter design features, potential design improvements and potential difficulties.

  5. Lung Volume Measured during Sequential Swallowing in Healthy Young Adults

    Science.gov (United States)

    Hegland, Karen Wheeler; Huber, Jessica E.; Pitts, Teresa; Davenport, Paul W.; Sapienza, Christine M.

    2011-01-01

    Purpose: Outcomes from studying the coordinative relationship between respiratory and swallow subsystems are inconsistent for sequential swallows, and the lung volume at the initiation of sequential swallowing remains undefined. The first goal of this study was to quantify the lung volume at initiation of sequential swallowing ingestion cycles and…

  6. Urban Run-off Volumes Dependency on Rainfall Measurement Method

    DEFF Research Database (Denmark)

    Pedersen, L.; Jensen, N. E.; Rasmussen, Michael R.;

    2005-01-01

    Urban run-off is characterized with fast response since the large surface run-off in the catchments responds immediately to variations in the rainfall. Modeling such type of catchments is most often done with the input from very few rain gauges, but the large variation in rainfall over small area...... resolutions and single gauge rainfall was fed to a MOUSE run-off model. The flow and total volume over the event is evaluated.......Urban run-off is characterized with fast response since the large surface run-off in the catchments responds immediately to variations in the rainfall. Modeling such type of catchments is most often done with the input from very few rain gauges, but the large variation in rainfall over small areas...... suggests that rainfall needs to be measured with a much higher spatial resolution (Jensen and Pedersen, 2004). This paper evaluates the impact of using high-resolution rainfall information from weather radar compared to the conventional single gauge approach. The radar rainfall in three different...

  7. Sources of errors in the measurements of underwater profiling radiometer

    Digital Repository Service at National Institute of Oceanography (India)

    Silveira, N.; Suresh, T.; Talaulikar, M.; Desa, E.; Matondkar, S.G.P.; Lotlikar, A.

    There are various sources of errors from the measurements of optical parameters using a radiometer, which can be classified as mode of deployment, instrument and environment. The errors from the deployment are primarily from the ship...

  8. Assessment of relative error sources in IR DIAL measurement accuracy

    Science.gov (United States)

    Menyuk, N.; Killinger, D. K.

    1983-01-01

    An assessment is made of the role the various error sources play in limiting the accuracy of infrared differential absorption lidar measurements used for the remote sensing of atmospheric species. An overview is presented of the relative contribution of each error source including the inadequate knowledge of the absorption coefficient, differential spectral reflectance, and background interference as well as measurement errors arising from signal fluctuations.

  9. The Chandra Local Volume Survey: The X-ray Point Source Catalog of NGC 300

    CERN Document Server

    Binder, Breanna; Eracleous, Michael; Gaetz, Terrance J; Plucinsky, Paul P; Skillman, Evan D; Dalcanton, Julianne J; Anderson, Scott F; Weisz, Daniel R; Kong, Albert K H

    2012-01-01

    We present the source catalog of a new Chandra ACIS-I observation of NGC 300 obtained as part of the Chandra Local Volume Survey. Our 63 ks exposure covers ~88% of the D25 isophote (R~6.3 kpc) and yields a catalog of 95 X-ray point sources detected at high significance to a limiting unabsorbed 0.35-8 keV luminosity of ~10^36 erg s^-1. Sources were cross-correlated with a previous XMM-Newton catalog, and we find 75 "X-ray transient candidate" sources that were detected by one observatory, but not the other. We derive an X-ray scale length of 1.7+/-0.2 kpc and a recent star formation rate of 0.12 Msun yr^-1, in excellent agreement with optical observations. Deep, multi-color imaging from the Hubble Space Telescope, covering ~32% of our Chandra field, was used to search for optical counterparts to the X-ray sources, and we have developed a new source classification scheme to determine which sources are likely X-ray binaries, supernova remnants, and background AGN candidates. Finally, we present the X-ray luminos...

  10. High-pitch dual-source CT coronary angiography with low volumes of contrast medium

    Energy Technology Data Exchange (ETDEWEB)

    Lembcke, Alexander; Hein, Patrick A.; Knobloch, Gesine; Durmus, Tahir; Hamm, Bernd [Charite - University Medicine Berlin, Department of Radiology, Berlin (Germany); Schwenke, Carsten [SCO:SSiS - Schwenke Consulting, Berlin (Germany); Huppertz, Alexander [Charite - University Medicine Berlin, Department of Radiology, Berlin (Germany); ISI - Imaging Science Institute Charite, Berlin (Germany)

    2014-01-15

    To assess the effect of lower volumes of contrast medium (CM) on image quality in high-pitch dual-source computed tomography coronary angiography (CTCA). One-hundred consecutive patients (body weight 65-85 kg, stable heart rate ≤65 bpm, cardiac index ≥2.5 L/min/m{sup 2}) referred for CTCA were prospectively enrolled. Patients were randomly assigned to one of five groups of different CM volumes (G{sub 30}, 30 mL; G{sub 40}, 40 mL; G{sub 50}, 50 mL; G{sub 60}, 60 mL; G{sub 70}, 70 mL; flow rate 5 mL/s each, iodine content 370 mg/mL). Attenuation within the proximal and distal coronary artery segments was analysed. Mean attenuation for men and women ranged from 345.0 and 399.1 HU in G{sub 30} to 478.2 and 571.8 HU in G{sub 70}. Mean attenuation values were higher in groups with higher CM volumes (P < 0.0001) and higher in women than in men (P < 0.0001). The proportions of segments with attenuation of at least 300 HU in G{sub 30}, G{sub 40}, G{sub 50}, G{sub 60} and G{sub 70} were 89 %, 95 %, 98 %, 98 % and 99 %. CM volume of 30 mL in women and 40 mL in men proved to be sufficient to guarantee attenuation of at least 300 HU. In selected patients high-pitch dual-source CTCA can be performed with CM volumes of 40 mL in men or 30 mL in women. (orig.)

  11. Linear and volume measurements of pulmonary nodules at different CT dose levels. Interscan and interscan analysis

    Energy Technology Data Exchange (ETDEWEB)

    Hein, P.A.; Romano, V.C.; Rogalla, P.; Klessen, C.; Lembcke, A.; Bauknecht, H.C. [Charite-Universitaetsmedizin Berlin (Germany). Inst. fuer Radiologie; Dicken, V.; Bornemann, L. [MeVis Research, Bremen (Germany)

    2009-01-15

    Purpose: To compare the interobserver variability of the unidimensional diameter and volume measurements of pulmonary nodules in an intrascan and interscan analysis using semi-automated segmentation software on ultra-low-dose computed tomography (ULD-CT) and standard dose CT (SD-CT) data. Materials and Methods: In 33 patients with pulmonary nodules, two chest multi-slice CT (MSCT) datasets (1 mm slice thickness; 20 % reconstruction overlap) had been consecutively acquired with an ultra-low dose (120 kV, 5 mAs) and standard dose technique (120 kV, 75 mAs). MSCT data was retrospectively analyzed using the segmentation software OncoTREAT (MeVis, Bremen, Germany, version 1.3). The volume of 229 solid pulmonary nodules included in the analysis as well as the largest diameter according to RECIST (Response Evaluation Criteria for Solid Tumors) were measured by two radiologists. Interobserver variability was calculated and SD-CT and ULD-CT data compared in an intrascan and interscan analysis. Results: The median nodule diameter (n = 229 nodules) was registered with 8.2 mm (range: 2.8 to 43.6 mm, mean: 10.8 mm). The nodule volume ranged between 0.01 and 49.1 ml (median 0.1 ml, mean 1.5 ml). With respect to interobserver variability, the intrascan analysis did not reveal statistically significant differences (p > 0.05) between ULD-CT and SD-CT with broader limits of agreement for relative differences of RECIST measurements (-31.0 % + 27.0 % mean -2.0 % for SD-CT; -27.0 % + 38.6 %, mean 5.8 % for ULD-CT) than for volume measurements (-9.4 %, 8.0 %, mean 0.7 % for SD-CT; -13 %, 13 %, mean 0.0 % for ULD-CT). The interscan analysis showed broadened 95 % confidence intervals for volume measurements (-26.5 % 29.1 % mean 1.3 %, and -25.2 %, 29.6 %, mean 2.2 %) but yielded comparable limits of agreement for RECIST measurements. Conclusion: The variability of nodule volumetry assessed by semi-automated segmentation software as well as nodule size determination by RECIST appears to be

  12. THE CHANDRA LOCAL VOLUME SURVEY: THE X-RAY POINT-SOURCE CATALOG OF NGC 300

    Energy Technology Data Exchange (ETDEWEB)

    Binder, B.; Williams, B. F.; Dalcanton, J. J.; Anderson, S. F.; Weisz, D. R. [Department of Astronomy, University of Washington, Box 351580, Seattle, WA 98195 (United States); Eracleous, M. [Department of Astronomy and Astrophysics, Pennsylvania State University, 525 Davey Laboratory, University Park, PA 16802 (United States); Gaetz, T. J.; Plucinsky, P. P. [Harvard-Smithsonian Center for Astrophysics, 60 Garden Street Cambridge, MA 02138 (United States); Skillman, E. D. [Astronomy Department, University of Minnesota, 116 Church St. SE, Minneapolis, MN 55455 (United States); Kong, A. K. H. [Institute of Astronomy and Department of Physics, National Tsing Hua University, Hsinchu 30013, Taiwan (China)

    2012-10-10

    We present the source catalog of a new Chandra ACIS-I observation of NGC 300 obtained as part of the Chandra Local Volume Survey. Our 63 ks exposure covers {approx}88% of the D{sub 25} isophote (R Almost-Equal-To 6.3 kpc) and yields a catalog of 95 X-ray point sources detected at high significance to a limiting unabsorbed 0.35-8 keV luminosity of {approx}10{sup 36} erg s{sup -1}. Sources were cross-correlated with a previous XMM-Newton catalog, and we find 75 'X-ray transient candidate' sources that were detected by one observatory, but not the other. We derive an X-ray scale length of 1.7 {+-} 0.2 kpc and a recent star formation rate of 0.12 M{sub Sun} yr{sup -1} in excellent agreement with optical observations. Deep, multi-color imaging from the Hubble Space Telescope, covering {approx}32% of our Chandra field, was used to search for optical counterparts to the X-ray sources, and we have developed a new source classification scheme to determine which sources are likely X-ray binaries, supernova remnants, and background active galactic nucleus candidates. Finally, we present the X-ray luminosity functions (XLFs) at different X-ray energies, and we find the total NGC 300 X-ray point-source population to be consistent with other late-type galaxies hosting young stellar populations ({approx}< 50 Myr). We find that XLF of sources associated with older stellar populations has a steeper slope than the XLF of X-ray sources coinciding with young stellar populations, consistent with theoretical predictions.

  13. A Review of the Definition and Measurement of Poverty: Volume I, Summary Review Paper; Volume II, Annotated Bibliography. The Measure of Poverty, Technical Paper III.

    Science.gov (United States)

    Oster, Sharon; And Others

    This study reviews the existing literature on a series of issues associated with the defintion and measurement of poverty, and it consists of a summary report covering this research (Volume I), and an annotated bibliography (Volume II). Eleven specific issues were identified and reviewed in this study: (1) the historical definitions of poverty,…

  14. Extrasynaptic exocytosis and its mechanisms: a source of molecules mediating volume transmission in the nervous system

    Directory of Open Access Journals (Sweden)

    Citlali eTrueta

    2012-09-01

    Full Text Available We review the evidence of exocytosis from extrasynaptic sites in the soma, dendrites and axonal varicosities of central and peripheral neurons of vertebrates and invertebrates, and how it may contribute to signaling in the nervous system. The finding of secretory vesicles in extrasynaptic sites of neurons, the presence of transmitters in the extracellular space outside synaptic clefts, and the mismatch between exocytosis sites and the location of receptors for these molecules in neurons and glial cells, have long suggested that in addition to synaptic communication, transmitters are released and act extrasynaptically. The catalog of these molecules includes low molecular weight transmitters such as monoamines, acetylcholine, glutamate, GABA, ATP, and a list of peptides including substance P, BDNF, and oxytocin. By comparing the mechanisms of extrasynaptic exocytosis of different molecules in various neuron types we show that extrasynaptic exocytosis is a widespread mechanism for communication in the nervous system that uses certain common mechanisms, which are different from those of synaptic exocytosis but similar to those of exocytosis from excitable endocrine cells. Somatic exocytosis, which has been measured directly in different neuron types, starts after high-frequency electrical activity or long experimental depolarizations and may continue for several minutes after the end of stimulation. Activation of L-type calcium channels, calcium release from intracellular stores and vesicle transport couples excitation and exocytosis from small clear or large dense core vesicles in release sites lacking postsynaptic counterparts. The presence of synaptic and extrasynaptic exocytosis endows individual neurons with a wide variety of time- and space-dependent communication possibilities. Extrasynaptic exocytosis may be the major source of signaling molecules producing volume transmission and by doing so may be part of a long duration signaling mode in

  15. Determining low-frequency source location from acoustic phase measurements

    Science.gov (United States)

    Poole, Travis L.; Frisk, George V.

    2002-11-01

    For low-frequency cw sound sources in shallow water, the time rate-of-change of the measured acoustic phase is well approximated by the time rate-of-change of the source-receiver separation distance. An algorithm for determining a locus of possible source locations based on this idea has been developed. The locus has the general form of a hyperbola, which can be used to provide a bearing estimation at long ranges, and an estimate of source location at short ranges. The algorithm uses only acoustic phase data and receiver geometry as input, and can be used even when the source frequency is slightly unstable and/or imprecisely known. The algorithm has been applied to data from low-frequency experiments (20-300 Hz), both for stable and unstable source frequencies, and shown to perform well. [Work supported by ONR and WHOI Academic Programs Office.

  16. Quantitation of mandibular ramus volume as a source of bone grafting.

    Science.gov (United States)

    Verdugo, Fernando; Simonian, Krikor; Smith McDonald, Roberto; Nowzari, Hessam

    2009-10-01

    When alveolar atrophy impairs dental implant placement, ridge augmentation using mandibular ramus graft may be considered. In live patients, however, an accurate calculation of the amount of bone that can be safely harvested from the ramus has not been reported. The use of a software program to perform these calculations can aid in preventing surgical complications. The aim of the present study was to intra-surgically quantify the volume of the ramus bone graft that can be safely harvested in live patients, and compare it to presurgical computerized tomographic calculations. The AutoCAD software program quantified ramus bone graft in 40 consecutive patients from computerized tomographies. Direct intra-surgical measurements were recorded thereafter and compared to software data (n = 10). In these 10 patients, the bone volume was also measured at the recipient sites 6 months post-sinus augmentation. The mandibular second and third molar areas provided the thickest cortical graft averaging 2.8 +/- 0.6 mm. The thinnest bone was immediately posterior to the third molar (1.9 +/- 0.3 mm). The volume of ramus bone graft measured by AutoCAD averaged 0.8 mL (standard deviation [SD] 0.2 mL, range: 0.4-1.2 mL). The volume of bone graft measured intra-surgically averaged 2.5 mL (SD 0.4 mL, range: 1.8-3.0 mL). The difference between the two measurement methods was significant (p AutoCAD software program did not overestimate the volume of bone that can be safely harvested from the mandibular ramus.

  17. 30 CFR 250.1163 - How must I measure gas flaring or venting volumes and liquid hydrocarbon burning volumes, and...

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 2 2010-07-01 2010-07-01 false How must I measure gas flaring or venting... SULPHUR OPERATIONS IN THE OUTER CONTINENTAL SHELF Oil and Gas Production Requirements Flaring, Venting, and Burning Hydrocarbons § 250.1163 How must I measure gas flaring or venting volumes and liquid...

  18. Intense Pulsed Neutron Source: Progress report 1991--1996. 15. Anniversary edition -- Volume 2

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-05-01

    The 15th Anniversary Edition of the IPNS Progress Report is being published in recognition of the Intense Pulsed Neutron Source`s first 15 years of successful operation as a user facility. To emphasize the importance of this milestone, the author shave made the design and organization of the report significantly different from previous IPNS Progress Reports. This report consists of two volumes. For Volume 1, authors were asked to prepare articles that highlighted recent scientific accomplishments at IPNS, from 1991 to present; to focus on and illustrate the scientific advances achieved through the unique capabilities of neutron studies performed by IPNS users; to report on specific activities or results from an instrument; or to focus on a body of work encompassing different neutron-scattering techniques. Articles were also included on the accelerator system, instrumentation, computing, target, and moderators. A list of published and ``in press` articles in journals, books, and conference proceedings, resulting from work done at IPNS since 1991, was compiled. This list is arranged alphabetically according to first author. Publication references in the articles are listed by last name of first author and year of publication. The IPNS experimental reports received since 1991 are compiled in Volume 2. Experimental reports referenced in the articles are listed by last name of first author, instrument designation, and experiment number.

  19. Intense Pulsed Neutron Source: Progress report 1991--1996. 15. Anniversary edition -- Volume 1

    Energy Technology Data Exchange (ETDEWEB)

    Marzec, B. [ed.

    1996-05-01

    The 15th Anniversary Edition of the IPNS Progress Report is being published in recognition of the Intense Pulsed Neutron Source`s first 15 years of successful operation as a user facility. To emphasize the importance of this milestone, the authors have made the design and organization of the report significantly different from previous IPNS Progress Reports. This report consists of two volumes. For Volume 1, authors were asked to prepare articles that highlighted recent scientific accomplishments at IPNS, from 1991 to present; to focus on and illustrate the scientific advances achieved through the unique capabilities of neutron studies performed by IPNS users; to report on specific activities or results from an instrument; or to focus on a body of work encompassing different neutron-scattering techniques. Articles were also included on the accelerator system, instrumentation, computing, target, and moderators. A list of published and ``in press` articles in journals, books, and conference proceedings, resulting from work done at IPNS since 1991, was compiled. This list is arranged alphabetically according to first author. Publication references in the articles are listed by last name of first author and year of publication. The IPNS experimental reports received since 1991 are compiled in Volume 2. Experimental reports referenced in the articles are listed by last name of first author, instrument designation, and experiment number.

  20. Characterizing heralded single-photon sources with imperfect measurement devices

    Energy Technology Data Exchange (ETDEWEB)

    Razavi, M; Soellner, I; Bocquillon, E; Couteau, C; Laflamme, R; Weihs, G [Institute for Quantum Computing, University of Waterloo, 200 University Ave. W, Waterloo, ON N2L 3G1 (Canada)], E-mail: mrazavi@iqc.ca

    2009-06-14

    Any characterization of a single-photon source is not complete without specifying its second-order degree of coherence, i.e., its g{sup (2)} function. An accurate measurement of such coherence functions commonly requires high-precision single-photon detectors, in whose absence only time-averaged measurements are possible. It is not clear, however, how the resulting time-averaged quantities can be used to properly characterize the source. In this paper, we investigate this issue for a heralded source of single photons that relies on continuous-wave parametric down-conversion. By accounting for major shortcomings of the source and the detectors-i.e., the multiple-photon emissions of the source, the time resolution of photodetectors and our chosen width of coincidence window-our theory enables us to infer the true source properties from imperfect measurements. Our theoretical results are corroborated by an experimental demonstration using a PPKTP crystal pumped by a blue laser that results in a single-photon generation rate about 1.2 millions per second per milliwatt of pump power. This work takes an important step towards the standardization of such heralded single-photon sources.

  1. Comparison of ultracold neutron sources for fundamental physics measurements

    CERN Document Server

    Bison, G; Kirch, K; Lauss, B; Ries, D; Schmidt-Wellenburg, P; Zsigmond, G; Brenner, T; Geltenbort, P; Jenke, T; Zimmer, O; Beck, M; Heil, W; Kahlenberg, J; Karch, J; Ross, K; Eberhardt, K; Geppert, C; Karpuk, S; Reich, T; Siemensen, C; Sobolev, Y; Trautmann, N

    2016-01-01

    Ultracold neutrons (UCNs) are key for precision studies of fundamental parameters of the neutron and in searches for new CP violating processes or exotic interactions beyond the Standard Model of particle physics. The most prominent example is the search for a permanent electric dipole moment of the neutron (nEDM). We have performed an experimental comparison of the leading UCN sources currently operating. We have used a 'standard' UCN storage bottle with a volume of 32 liters, comparable in size to nEDM experiments, which allows us to compare the UCN density available at a given beam port.

  2. The Use of Helmholtz Resonance for Measuring the Volume of Liquids and Solids

    Directory of Open Access Journals (Sweden)

    Clive E. Davies

    2010-11-01

    Full Text Available An experimental investigation was undertaken to ascertain the potential of using Helmholtz resonance for volume determination and the factors that may influence accuracy. The uses for a rapid non-interference volume measurement system range from agricultural produce and mineral sampling through to liquid fill measurements. By weighing the sample the density can also measured indirectly.

  3. The use of Helmholtz resonance for measuring the volume of liquids and solids.

    Science.gov (United States)

    Webster, Emile S; Davies, Clive E

    2010-01-01

    An experimental investigation was undertaken to ascertain the potential of using Helmholtz resonance for volume determination and the factors that may influence accuracy. The uses for a rapid non-interference volume measurement system range from agricultural produce and mineral sampling through to liquid fill measurements. By weighing the sample the density can also measured indirectly.

  4. The Einstein Observatory catalog of IPC x ray sources. Volume 1E: Documentation

    Science.gov (United States)

    Harris, D. E.; Forman, W.; Gioia, I. M.; Hale, J. A.; Harnden, F. R., Jr.; Jones, C.; Karakashian, T.; Maccacaro, T.; Mcsweeney, J. D.; Primini, F. A.

    1993-01-01

    The Einstein Observatory (HEAO-2, launched November 13, 1978) achieved radically improved sensitivity over previous x-ray missions through the use of focusing optics, which simultaneously afforded greatly reduced background and produced true images. During its 2.5-yr mission, the Einstein X-Ray Telescope was pointed toward some 5,000 celestial targets, most of which were detected, and discovered several thousand additional 'serendipitous' sources in the observed fields. This catalog contains contour diagrams and source data, obtained with the imaging proportional counter in the 0.16 to 3.5 keV energy band, and describes methods for recovering upper limits for any sky position within the observed images. The main catalog consists of six volumes (numbered 2 through 7) of right ascension ordered pages, each containing data for one observation. Along with the primary documentation describing how the catalog was constructed, volume 1 contains a complete source list, results for merged fields, a reference system to published papers, and data useful for calculating upper limits and fluxes.

  5. Single CMOS sensor system for high resolution double volume measurement applied to membrane distillation system

    Science.gov (United States)

    Lorenz, M. G.; Izquierdo-Gil, M. A.; Sanchez-Reillo, R.; Fernandez-Pineda, C.

    2007-01-01

    Membrane distillation (MD) [1] is a relatively new process that is being investigated world-wide as a low cost, energy saving alternative to conventional separation processes such as distillation and reverse osmosis (RO). This process offers some advantages compared to other more popular separation processes, such as working at room conditions (pressure and temperature); low-grade, waste and/or alternative energy sources such as solar and geothermal energy may be used; a very high level of rejection with inorganic solutions; small equipment can be employed, etc. The driving force in MD processes is the vapor pressure difference across the membrane. A temperature difference is imposed across the membrane, which results in a vapor pressure difference. The principal problem in this kind of system is the accurate measurement of the recipient volume change, especially at very low flows. A cathetometer, with up to 0,05 mm resolution, is the instrument used to take these measurements, but the necessary human intervention makes this instrument not suitable for automated systems. In order to overcome this lack, a high resolution system is proposed, that makes automatic measurements of the volume of both recipients, cold and hot, at a rate of up to 10 times per second.

  6. Measurements of the subcriticality using advanced technique of shooting source during operation of NPP reactors

    Science.gov (United States)

    Lebedev, G. V.; Petrov, V. V.; Bobylyov, V. T.; Butov, R. I.; Zhukov, A. M.; Sladkov, A. A.

    2014-12-01

    According to the rules of nuclear safety, the measurements of the subcriticality of reactors should be carried out in the process of performing nuclear hazardous operations. An advanced technique of shooting source of neutrons is proposed to meet this requirement. As such a source, a pulsed neutron source (PNS) is used. In order to realize this technique, it is recommended to enable a PNS with a frequency of 1-20 Hz. The PNS is stopped after achieving a steady-state (on average) number of neutrons in the reactor volume. The change in the number of neutrons in the reactor volume is measured in time with an interval of discreteness of ˜0.1 s. The results of these measurements with the application of a system of point-kinetics equations are used in order to calculate the sought subcriticality. The basic idea of the proposed technique used to measure the subcriticality is elaborated in a series of experiments on the Kvant assembly. The conditions which should be implemented in order to obtain a positive result of measurements are formulated. A block diagram of the basic version of the experimental setup is presented, whose main element is a pulsed neutron generator.

  7. Negative hydrogen ion production in multicusp volume source with a pulsed discharge (abstract)a)

    Science.gov (United States)

    Bacal, M.; Belchenko, Yu. I.

    1996-03-01

    The pulsed operation of a negative ion volume source has been investigated, both with a magnetic filter present and without it, under conditions of full-scale acceleration of the extracted negative hydrogen ion beam. We report the observation of three afterglow negative ion peaks. As the negative ion current during the discharge pulse, each of the afterglow peaks can be optimized by varying the pressure, the plasma electrode bias and the extraction voltage. Under optimum conditions, the negative ion current during the discharge pulse exceeds the afterglow peaks.

  8. Inversion of Atmospheric Tracer Measurements, Localization of Sources

    Science.gov (United States)

    Issartel, J.-P.; Cabrit, B.; Hourdin, F.; Idelkadi, A.

    When abnormal concentrations of a pollutant are observed in the atmosphere, the question of its origin arises immediately. The radioactivity from Tchernobyl was de- tected in Sweden before the accident was announced. This situation emphasizes the psychological, political and medical stakes of a rapid identification of sources. In tech- nical terms, most industrial sources can be modeled as a fixed point at ground level with undetermined duration. The classical method of identification involves the cal- culation of a backtrajectory departing from the detector with an upstream integration of the wind field. We were first involved in such questions as we evaluated the ef- ficiency of the international monitoring network planned in the frame of the Com- prehensive Test Ban Treaty. We propose a new approach of backtracking based upon the use of retroplumes associated to available measurements. Firstly the retroplume is related to inverse transport processes, describing quantitatively how the air in a sam- ple originates from regions that are all the more extended and diffuse as we go back far in the past. Secondly it clarifies the sensibility of the measurement with respect to all potential sources. It is therefore calculated by adjoint equations including of course diffusive processes. Thirdly, the statistical interpretation, valid as far as sin- gle particles are concerned, should not be used to investigate the position and date of a macroscopic source. In that case, the retroplume rather induces a straightforward constraint between the intensity of the source and its position. When more than one measurements are available, including zero valued measurements, the source satisfies the same number of linear relations tightly related to the retroplumes. This system of linear relations can be handled through the simplex algorithm in order to make the above intensity-position correlation more restrictive. This method enables to manage in a quantitative manner the

  9. Measuring x-ray spectra of flash radiographic sources

    Science.gov (United States)

    Gehring, Amanda E.; Espy, Michelle A.; Haines, Todd J.; Mendez, Jacob; Moir, David C.; Sedillo, Robert; Shurter, Roger P.; Volegov, Petr; Webb, Timothy J.

    2015-08-01

    A Compton spectrometer has been re-commissioned for measurements of flash radiographic sources. The determination of the energy spectrum of these sources is difficult due to the high count rates and short nature of the pulses (~50 ns). The spectrometer is a 300 kg neodymium-iron magnet which measures spectra in the <1 MeV to 20 MeV energy range. Incoming x-rays are collimated into a narrow beam incident on a converter foil. The ejected Compton electrons are collimated so that the forward-directed electrons enter the magnetic field region of the spectrometer. The position of the electrons at the magnet's focal plane is a function of their momentum, allowing the x-ray spectrum to be reconstructed. Recent measurements of flash sources are presented.

  10. Development of point source PM10 measurement methods

    Energy Technology Data Exchange (ETDEWEB)

    McCain, J.D.; Fowler, C.S.; Farthing, W.E. [Southern Research Institute, Birmingham, AL (United States)

    1994-09-01

    The purpose is to develop measurement methods for sampling high temperature and high moisture flue gases that contain particles with diameters larger than 10 micrometres. In a procedure developed to sample wet sources, the large droplets are removed and the sample gas stream is heated to dry the smaller droplets. Special construction materials and an air cooled probe are required to sample high temperature sources. The hardware and methodology developed for these procedures (EPA Methods 201 and 201A) are suitable for measuring PM{sub 10} emissions. Adaptation of these methods to solve some of the difficulties of measuring and characterizing particulate emissions is discussed. Background, the right angle precollector (RAPC), and development and testing of prototypes of a high temperature system and a wet source system are described. 14 refs., 5 figs.

  11. SU-E-I-79: Source Geometry Dependence of Gamma Well-Counter Measurements

    Energy Technology Data Exchange (ETDEWEB)

    Park, M; Belanger, A; Kijewski, M [Brigham and Women’s Hospital and Harvard Medical School, Boston, MA (United States)

    2015-06-15

    Purpose: To determine the effect of liquid sample volume and geometry on counting efficiency in a gamma well-counter, and to assess the relative contributions of sample geometry and self-attenuation. Gamma wellcounters are standard equipment in clinical and preclinical studies, for measuring patient blood radioactivity and quantifying animal tissue uptake for tracer development and other purposes. Accurate measurements are crucial. Methods: Count rates were measured for aqueous solutions of 99m- Tc at four liquid volume values in a 1-cm-diam tube and at six volume values in a 2.2-cm-diam vial. Total activity was constant for all volumes, and data were corrected for decay. Count rates from a point source in air, supported by a filter paper, were measured at seven heights between 1.3 and 5.7 cm from the bottom of a tube. Results: Sample volume effects were larger for the tube than for the vial. For the tube, count efficiency relative to a 1-cc volume ranged from 1.05 at 0.05 cc to 0.84 at 3 cc. For the vial, relative count efficiency ranged from 1.02 at 0.05 cc to 0.87 at 15 cc. For the point source, count efficiency relative to 1.3 cm from the tube bottom ranged from 0.98 at 1.8 cm to 0.34 at 5.7 cm. The relative efficiency of a 3-cc liquid sample in a tube compared to a 1-cc sample is 0.84; the average relative efficiency for the solid sample in air between heights in the tube corresponding to the surfaces of those volumes (1.3 and 4.8 cm) is 0.81, implying that the major contribution to efficiency loss is geometry, rather than attenuation. Conclusion: Volume-dependent correction factors should be used for accurate quantitation radioactive of liquid samples. Solid samples should be positioned at the bottom of the tube for maximum count efficiency.

  12. Triphasic MRI of pelvic organ descent: sources of measurement error

    Energy Technology Data Exchange (ETDEWEB)

    Morren, Geert L. [Bowel and Digestion Centre, The Oxford Clinic, 38 Oxford Terrace, Christchurch (New Zealand)]. E-mail: geert_morren@hotmail.com; Balasingam, Adrian G. [Christchurch Radiology Group, P.O. Box 21107, 4th Floor, Leicester House, 291 Madras Street, Christchurch (New Zealand); Wells, J. Elisabeth [Department of Public Health and General Medicine, Christchurch School of Medicine, St. Elmo Courts, Christchurch (New Zealand); Hunter, Anne M. [Christchurch Radiology Group, P.O. Box 21107, 4th Floor, Leicester House, 291 Madras Street, Christchurch (New Zealand); Coates, Richard H. [Christchurch Radiology Group, P.O. Box 21107, 4th Floor, Leicester House, 291 Madras Street, Christchurch (New Zealand); Perry, Richard E. [Bowel and Digestion Centre, The Oxford Clinic, 38 Oxford Terrace, Christchurch (New Zealand)

    2005-05-01

    Purpose: To identify sources of error when measuring pelvic organ displacement during straining using triphasic dynamic magnetic resonance imaging (MRI). Materials and methods: Ten healthy nulliparous woman underwent triphasic dynamic 1.5 T pelvic MRI twice with 1 week between studies. The bladder was filled with 200 ml of a saline solution, the vagina and rectum were opacified with ultrasound gel. T2 weighted images in the sagittal plane were analysed twice by each of the two observers in a blinded fashion. Horizontal and vertical displacement of the bladder neck, bladder base, introitus vaginae, posterior fornix, cul-de sac, pouch of Douglas, anterior rectal wall, anorectal junction and change of the vaginal axis were measured eight times in each volunteer (two images, each read twice by two observers). Variance components were calculated for subject, observer, week, interactions of these three factors, and pure error. An overall standard error of measurement was calculated for a single observation by one observer on a film from one woman at one visit. Results: For the majority of anatomical reference points, the range of displacements measured was wide and the overall measurement error was large. Intra-observer error and week-to-week variation within a subject were important sources of measurement error. Conclusion: Important sources of measurement error when using triphasic dynamic MRI to measure pelvic organ displacement during straining were identified. Recommendations to minimize those errors are made.

  13. Capillary plasma jet: A low volume plasma source for life science applications

    Energy Technology Data Exchange (ETDEWEB)

    Topala, I., E-mail: ionut.topala@uaic.ro, E-mail: tmnagat@ipc.shizuoka.ac.jp [Alexandru Ioan Cuza University of Iasi, Faculty of Physics, Iasi Plasma Advanced Research Center (IPARC), Bd. Carol I No. 11, Iasi 700506 (Romania); Nagatsu, M., E-mail: ionut.topala@uaic.ro, E-mail: tmnagat@ipc.shizuoka.ac.jp [Graduate School of Science and Technology, Shizuoka University, 3-5-1 Johoku, Naka-ku, Hamamatsu 432-8561 (Japan)

    2015-02-02

    In this letter, we present results from multispectroscopic analysis of protein films, after exposure to a peculiar plasma source, i.e., the capillary plasma jet. This plasma source is able to generate very small pulsed plasma volumes, in kilohertz range, with characteristic dimensions smaller than 1 mm. This leads to specific microscale generation and transport of all plasma species. Plasma diagnosis was realized using general electrical and optical methods. Depending on power level and exposure duration, this miniature plasma jet can induce controllable modifications to soft matter targets. Detailed discussions on protein film oxidation and chemical etching are supported by results from absorption, X-ray photoelectron spectroscopy, and microscopy techniques. Further exploitation of principles presented here may consolidate research interests involving plasmas in biotechnologies and plasma medicine, especially in patterning technologies, modified biomolecule arrays, and local chemical functionalization.

  14. Evaluation of left ventricular volumes measured by magnetic resonance imaging

    DEFF Research Database (Denmark)

    Møgelvang, J; Thomsen, C; Mehlsen, J

    1986-01-01

    Left ventricular end-diastolic and end-systolic volumes were determined in 17 patients with different levels of left ventricular function by magnetic resonance imaging (MRI). A 1.5 Tesla Magnet was used obtaining ECG triggered single and multiple slices. Calculated cardiac outputs were compared...

  15. Comparative analysis of two methods for measuring sales volumes during malaria medicine outlet surveys

    OpenAIRE

    Patouillard, Edith; Kleinschmidt, Immo; Hanson, Kara; Pok, Sochea; Palafox, Benjamin; Tougher, Sarah; O’Connell, Kate; Goodman, Catherine

    2013-01-01

    Background There is increased interest in using commercial providers for improving access to quality malaria treatment. Understanding their current role is an essential first step, notably in terms of the volume of diagnostics and anti-malarials they sell. Sales volume data can be used to measure the importance of different provider and product types, frequency of parasitological diagnosis and impact of interventions. Several methods for measuring sales volumes are available, yet all have met...

  16. Comparative analysis of two methods for measuring sales volumes during malaria medicine outlet surveys.

    OpenAIRE

    Patouillard, E; Kleinschmidt, I.; Hanson, K.; Pok, S; Palafox, B; Tougher, S; O Connell, K.; Goodman, C.

    2013-01-01

    BACKGROUND There is increased interest in using commercial providers for improving access to quality malaria treatment. Understanding their current role is an essential first step, notably in terms of the volume of diagnostics and anti-malarials they sell. Sales volume data can be used to measure the importance of different provider and product types, frequency of parasitological diagnosis and impact of interventions. Several methods for measuring sales volumes are available, yet all have met...

  17. Volumes of chronic traumatic frontal brain lesions measured by MR imaging and CBF tomography

    Energy Technology Data Exchange (ETDEWEB)

    Maeder, P.; Wirsen, A.; Bajc, M.; Schalen, W.; Sjoeholm, H.; Skeidsvoll, H.; Cronqvist, S.; Ingvar, D.H. (University Hospital, Lund (Sweden). Dept. of Neuroradiology University Hospital, Lund (Sweden). Dept. of Clinical Neurophysiology University Hospital, Lund (Sweden). Dept. of Neurosurgery)

    1991-07-01

    The volumes (ml) of chronic traumatic frontal brain lesions were compared measured 'morphologically' with MR imaging (T1 and T2 weighted images) and 'functionally' with a tomographic rCBF technique (SPECT with {sup 133}Xe i.v.). The T1 volumes varied between 11 and 220 ml. The correlation between T1 and T2 volumes was 0.95, the T2 volumes being 33% larger than T1 volumes (p<0.001). The functional SPECT volumes were considerably larger (range 16-324 ml) than the MR volumes. The mean volume difference was 81% between T1 and SPECT images (p<0.001), and 35% between T2 and SPECT images (p<0.001). Correlations between the MR and SPECT volumes were also higher for T2 than T1 volumes. The volume difference is most likely explained by a functional decrease in regions around the lesion in which no morphologic change visible on MR images had taken place. MR and SPECT volume measurements were positively related to persistent lack of energy and personality changes, but only moderately related to duration of impaired consciousness and neuropsychologie outcome. (orig.).

  18. Measurements of Martin-Puplett Interferometer Limitations using Blackbody Source

    Energy Technology Data Exchange (ETDEWEB)

    Evtushenko, Pavel E. [JLAB; Klopf, John M. [JLAB

    2013-06-01

    Frequency domain measurements with Martin-Puplett interferometer is one of a few techniques capable of bunch length measurements at the level of ~ 100 fs. As the bunch length becomes shorter, it is important to know and be able to measure the limitations of the instrument in terms of shortest measurable bunch length. In this paper we describe an experiment using a blackbody source with the modified Martin-Puplett interferometer that is routine- ly used for bunch length measurements at the JLab FEL, as a way to estimate the shortest, measurable bunch length. The limitation comes from high frequency cut-off of the wire-grid polarizer currently used and is estimated to be 50 fs RMS. The measurements are made with the same Golay cell detector that is used for beam measure- ments. We demonstrate that, even though the blackbody source is many orders of magnitude less bright than the coherent transition or synchrotron radiation, it can be used for the measurements and gives a very good signal to noise ratio in combination with lock-in detection. We also compare the measurements made in air and in vacuum to characterize the very strong effect of the atmospheric absorption.

  19. Measurement of parameters in Indus-2 synchrotron radiation source.

    Science.gov (United States)

    Ghodke, A D; Husain, Riyasat; Kumar, Pradeep; Yadav, Surendra; Puntambekar, T A

    2012-10-01

    The paper presents the measurement of optics parameters in Indus-2 synchrotron radiation source, which include betatron tune, beta function, dispersion function, natural chromaticity, corrected chromaticity, central RF frequency, momentum compaction factor, and linear betatron coupling. Two methods were used for beta function measurement; a conventional quadrupole scan method and a method using the fitting of the orbit response matrix. A robust Levenberg-Marquardt algorithm was used for nonlinear least square fitting of the orbit response matrix. In this paper, detailed methods for the parameter measurements are described. The measured results are discussed and compared with the theoretical values obtained using accelerator simulation code Accelerator Toolbox in MATLAB.

  20. The Chandra Local Volume Survey: The X-ray Point Source Population of NGC 404

    CERN Document Server

    Binder, B; Eracleous, M; Gaetz, T J; Kong, A K H; Skillman, E D; Weisz, D R

    2012-01-01

    We present a comprehensive X-ray point source catalog of NGC 404 obtained as part of the Chandra Local Volume Survey. A new, 97 ks Chandra ACIS-S observation of NGC 404 was combined with archival observations for a total exposure of ~123 ks. Our survey yields 74 highly significant X-ray point sources and is sensitive to a limiting unabsorbed luminosity of ~6x10^35 erg s^-1 in the 0.35-8 keV band. To constrain the nature of each X-ray source, cross-correlations with multi-wavelength data were generated. We searched overlapping HST observations for optical counterparts to our X-ray detections, but find only two X-ray sources with candidate optical counterparts. We find 21 likely low mass X-ray binaries (LMXBs), although this number is a lower limit due to the difficulties in separating LMXBs from background AGN. The X-ray luminosity functions (XLFs) in both the soft and hard energy bands are presented. The XLFs in the soft band (0.5-2 keV) and the hard band (2-8 keV) have a limiting luminosity at the 90% comple...

  1. A High-Temperature, "Volume-Type" ECR Ion Source for RIB Generation

    Energy Technology Data Exchange (ETDEWEB)

    Alton, G.D.; Liu, Y.; Reed, C.A.; Williams, C.; Zhang, T.

    1999-03-29

    A high temperature, low-charge-state, "volume-type" source has been designed for use in the nuclear physics and nuclear astrophysics research radioactive ion beam (RIB) programs at the Holifield Radioactive Ion beam Facility (HRIBF). The source utilizes electromagnetic coils to generate a large and uniformly distributed central magnetic field with magnitude (875 G) chosen to be in electron-cyclotron-resonance (ECR) with single- frequency (2.45 GHz) microwave radiation. Among the features of the source includti a variable mirror-ratio at ion extraction as required for optimizing low-charge state ion beam generation, a right-hand, circularly-polarized RF injection system to overcome the relatively-low, cutoff-density, (nC - 7.4x10'0/cm3) associated with the use of 2.45 GHz microwave radiatiom, and a high temperature, Ir- or Re-coated-Ta plasma chamber to reduce the residence times of radioactive species that are adsorbed on the walls of the chamber. No provisions are made for radial plasma confinement due to the sensitivity of permanent magnets to degradation by the huge fluxes of neutrons incumbent during target irradiation, routinely used for this purpose. Aspects of the design features of the source are described in this report.

  2. Advisory Committee on human radiation experiments. Final report, Supplemental Volume 2. Sources and documentation

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-01-01

    This volume and its appendixes supplement the Advisory Committee`s final report by reporting how we went about looking for information concerning human radiation experiments and intentional releases, a description of what we found and where we found it, and a finding aid for the information that we collected. This volume begins with an overview of federal records, including general descriptions of the types of records that have been useful and how the federal government handles these records. This is followed by an agency-by-agency account of the discovery process and descriptions of the records reviewed, together with instructions on how to obtain further information from those agencies. There is also a description of other sources of information that have been important, including institutional records, print resources, and nonprint media and interviews. The third part contains brief accounts of ACHRE`s two major contemporary survey projects (these are described in greater detail in the final report and another supplemental volume) and other research activities. The final section describes how the ACHRE information-nation collections were managed and the records that ACHRE created in the course of its work; this constitutes a general finding aid for the materials deposited with the National Archives. The appendices provide brief references to federal records reviewed, descriptions of the accessions that comprise the ACHRE Research Document Collection, and descriptions of the documents selected for individual treatment. Also included are an account of the documentation available for ACHRE meetings, brief abstracts of the almost 4,000 experiments individually described by ACHRE staff, a full bibliography of secondary sources used, and other information.

  3. Blood volume measurement with indocyanine green pulse spectrophotometry: dose and site of dye administration

    NARCIS (Netherlands)

    M.R. Germans; P.C. de Witt Hamer; L.J. van Boven; K.A.H. Zwinderman; G.J. Bouma

    2010-01-01

    (1) To determine the optimal administration site and dose of indocyanine green (ICG) for blood volume measurement using pulse spectrophotometry, (2) to assess the variation in repeated blood volume measurements for patients after subarachnoid hemorrhage and (3) to evaluate the safety and efficacy of

  4. Archimedes Revisited: A Faster, Better, Cheaper Method of Accurately Measuring the Volume of Small Objects

    Science.gov (United States)

    Hughes, Stephen W.

    2005-01-01

    A little-known method of measuring the volume of small objects based on Archimedes' principle is described, which involves suspending an object in a water-filled container placed on electronic scales. The suspension technique is a variation on the hydrostatic weighing technique used for measuring volume. The suspension method was compared with two…

  5. Spatial Visualization Tasks to Support Students' Spatial Structuring in Learning Volume Measurement

    Science.gov (United States)

    Revina, Shintia; Zulkardi; Darmawijoyo; van Galen, Frans

    2011-01-01

    Many prior researches found that most of students in grade five tended to have difficulty in fully grasping the concept of volume measurement because they have to build their competence in spatial structuring. The unit of volume "packing" measurement must be integrated and coordinated in three-dimension. On the other hand, it is revealed…

  6. Three-dimensional sonographic measurement of normal fetal brain volume during the second half of pregnancy

    NARCIS (Netherlands)

    N.M. Roelfsema; W.C.J. Hop (Wim); S.M. Boito; J.W. Wladimiroff (Juriy)

    2004-01-01

    textabstractObjectives: This study was undertaken to develop a three-dimensional (3D) ultrasound method of measuring fetal brain volume. Study design: Serial 3D sonographic measurements of fetal brain volume were made in 68 normal singleton pregnancies at 18 to 34 weeks of gestation. A comparison

  7. The Effect of a Finite Measurement Volume on Power Spectra from a Burst Type LDA

    DEFF Research Database (Denmark)

    Buchhave, Preben; Velte, Clara Marika; K. George, William

    2014-01-01

    We analyze the effects of a finite size measurement volume on the power spectrum computed fromdata acquired with a burst-type laser Doppler anemometer. The finite measurement volume causes temporal distortions in acquisition of the data resulting in phenomena such as finite processing time and de...

  8. Pile volume measurement by range imaging camera in indoor environment

    OpenAIRE

    C. Altuntas

    2014-01-01

    Range imaging (RIM) camera is recent technology in 3D location measurement. The new study areas have been emerged in measurement and data processing together with RIM camera. It has low-cost and fast measurement technique compared to the current measurement techniques. However its measurement accuracy varies according to effects resulting from the device and the environment. The direct sunlight is affect measurement accuracy of the camera. Thus, RIM camera should be used for indoor ...

  9. Emittance measurements for the Illinois/CEBAF polarized electron source

    Energy Technology Data Exchange (ETDEWEB)

    Dunham, B.M.; Cardman, L.S. [Illinois Univ., Urbana, IL (United States); Sinclair, C.K. [Continuous Electron Beam Accelerator Facility, Newport News, VA (United States)

    1995-01-01

    The transverse thermal properties of the electrons photoemitted from GaAs determine the intrinsic beam emittance, an important quantity in applications such as polarized electron sources and high-brightness sources. In this paper, emittance measurements using the Illinois/CEBAF polarized electron source are described. The emittance was measured as a function of both the laser beam spot size and laser wavelength at low currents. The data was used to infer the transverse thermal energy of the electrons photoemitted from GaAs for wavelengths between 514 and 840 nm. Near the bandgap the transverse energy is {approximately}34 meV, a factor of 3 lower than that of the beam from a typical thermionic electron gun. 8 refs., 2 figs.

  10. Comparison of medical of volume measurement of the prostate by transrectal ultrasound: Experiment with jelly models

    Energy Technology Data Exchange (ETDEWEB)

    Cho, Jeong Yeon; Lee, Hak Jong; Kim, Sung Hyun [Samsung Seoul Hospital, Sungkyunkwan University School of Medicine, Seoul (Korea, Republic of); Kim, Seung Hyup [Seoul National University College of Medicine, Seoul (Korea, Republic of)

    2002-03-15

    To evaluate the accuracy of measuring the volume of the prostate using the prolate ellipsoid volume calculation method (antero-posterior (AP) diameter X length X width X {pi}6) when the antero-posterior diameter of the prostate was measured on midsagittal (sagittal volume) and axial plane (axial volume).The devil's tongue jelly was used for the creation of ultrasound model of the prostate (volume: 15-40 cc) by cutting and shaping the surface. The volume in 10 prostatic models and 30 patients was measured and calculated. First, the AP diameter and length of the prostate models in midsagittal plane, and the height and width of the models in axial plane were measured for 3 times. The volume was calculated in two ways, one using the AP diameter an midsagittal plane and the other using the AP diameter in axial plane. The true volume of the model was measured using mess cylinder. The calculated volume and true volume were compared, and the accuracy of two method of measuring the prostatic volume was evaluated by Friedman test. The intraobserver variation was evaluated by General Linear Model, Repeated Measure. The reproducibility was evaluated by Cronbach's {alpha}. In vivo study was also performed in 30 patients. The prostate volume was calculated in the same manner. These volume data were analyzed by statistical method, and the intraobeserver variation was evaluated. While there was a statistically significant difference between the sagittal and true volume of the models, there was no statistical significant difference between the axial and true volumes. There was no significant intraobserver variation between both methods. The reproducibility was high in both methods with Cronbach's {alpha} of 0.977 and 0.942. The sagittal volume was larger than the axial volume in 30 patients with a statistically significant difference. There was no significant intraobserver variation in both methods. The reproducibility was high in both methods Cronbach's {alpha

  11. Precise Measurement of Separation Between Two Spherical Source Masses

    Institute of Scientific and Technical Information of China (English)

    陈德才; 罗俊; 胡忠坤; 赵亮

    2004-01-01

    A driving gauge method is performed to determine the separation between two spherical source masses in the measurement of Newtonian gravitational constant G. The experimental result shows that the uncertainty of determining the separation is about 0.35μm, which would contribute an uncertainty of 7.3ppm to the value of G.

  12. Recent Developments in Using Measured Sources in Computational EMC

    DEFF Research Database (Denmark)

    Sørensen, Morten; Franek, Ondrej; Pedersen, Gert F.

    2015-01-01

    This paper gives an overview of the recent developments in using near-field scanning for proactive EMC work. The aim is to use measured near fields as a source for simulations in order to predict radiated emission from printed circuit boards placed in a product. Far fields were predicted based...

  13. Measurement of and Factors Associated with the Anterior Chamber Volume in Healthy Chinese Adults

    Directory of Open Access Journals (Sweden)

    Yuan Zong

    2017-01-01

    Full Text Available Purpose. To measure the anterior chamber volume (ACV and determine factors associated with the ACV in healthy Chinese adults. Methods. In this cross-sectional study, we used swept-source optical coherence tomography (SS-OCT to measure ACV and other anterior segment parameters. Factors associated with ACV were also determined. Results. A total of 313 healthy Chinese adults were enrolled. The anterior segment parameters, including ACV, could be measured by SS-OCT with excellent repeatability and reproducibility. There was a significant difference between the horizontal and vertical anterior chamber widths (ACW (P<0.05, with a mean difference of 390 μm. The ACV (mean 153.83±32.42 mm3 was correlated with most of the anterior segment parameters, especially anterior chamber depth (ACD, which accounted for about 85% of the variation of ACV. Most of the anterior segment parameters were significantly correlated with age, and the relative changes in ACV and ACD were greatest in subjects aged 41–50 years. Conclusion. ACV was correlated with most of the anterior segment parameters measured in this study, particularly ACD. The relatively large difference between horizontal and vertical ACW suggests that the ACV could and should be measured using multiple OCT scans.

  14. Measurement of and Factors Associated with the Anterior Chamber Volume in Healthy Chinese Adults.

    Science.gov (United States)

    Zong, Yuan; Xu, Qian; Jiang, Chunhui; Zhu, Haohao; Yu, Jian; Sun, Xinghuai

    2017-01-01

    Purpose. To measure the anterior chamber volume (ACV) and determine factors associated with the ACV in healthy Chinese adults. Methods. In this cross-sectional study, we used swept-source optical coherence tomography (SS-OCT) to measure ACV and other anterior segment parameters. Factors associated with ACV were also determined. Results. A total of 313 healthy Chinese adults were enrolled. The anterior segment parameters, including ACV, could be measured by SS-OCT with excellent repeatability and reproducibility. There was a significant difference between the horizontal and vertical anterior chamber widths (ACW) (P ACV (mean 153.83 ± 32.42 mm(3)) was correlated with most of the anterior segment parameters, especially anterior chamber depth (ACD), which accounted for about 85% of the variation of ACV. Most of the anterior segment parameters were significantly correlated with age, and the relative changes in ACV and ACD were greatest in subjects aged 41-50 years. Conclusion. ACV was correlated with most of the anterior segment parameters measured in this study, particularly ACD. The relatively large difference between horizontal and vertical ACW suggests that the ACV could and should be measured using multiple OCT scans.

  15. Source apportionment of hydrocarbons measured in the Eagle Ford shale

    Science.gov (United States)

    Roest, G. S.; Schade, G. W.

    2016-12-01

    The rapid development of unconventional oil and gas in the US has led to hydrocarbon emissions that are yet to be accurately quantified. Emissions from the Eagle Ford Shale in southern Texas, one of the most productive shale plays in the U.S., have received little attention due to a sparse air quality monitoring network, thereby limiting studies of air quality within the region. We use hourly atmospheric hydrocarbon and meteorological data from three locations in the Eagle Ford Shale to assess their sources. Data are available from the Texas commission of environmental quality (TCEQ) air quality monitors in Floresville, a small town southeast of San Antonio and just north of the shale area; and Karnes city, a midsize rural city in the center of the shale. Our own measurements were carried out at a private ranch in rural Dimmit County in southern Texas from April to November of 2015. Air quality monitor data from the TCEQ were selected for the same time period. Non-negative matrix factorization in R (package NMF) was used to determine likely sources and their contributions above background. While the TCEQ monitor data consisted mostly of hydrocarbons, our own data include both CO, CO2, O3, and NOx. We find that rural Dimmit County hydrocarbons are dominated by oil and gas development sources, while central shale hydrocarbons at the TCEQ monitoring sites have a mix of sources including car traffic. However, oil and gas sources also dominate hydrocarbons at Floresville and Karnes City. Toxic benzene is nearly exclusively due to oil and gas development sources, including flaring, which NMF identifies as a major hydrocarbon source in Karnes City. Other major sources include emissions of light weight alkanes (C2-C5) from raw natural gas emissions and a larger set of alkanes (C2-C10) from oil sources, including liquid storage tanks.

  16. Two-dimensional ultrasound measurement of thyroid gland volume: a new equation with higher correlation with 3-D ultrasound measurement.

    Science.gov (United States)

    Ying, Michael; Yung, Dennis M C; Ho, Karen K L

    2008-01-01

    This study aimed to develop a new two-dimensional (2-D) ultrasound thyroid volume estimation equation using three-dimensional (3-D) ultrasound as the standard of reference, and to compare the thyroid volume estimation accuracy of the new equation with three previously reported equations. 2-D and 3-D ultrasound examinations of the thyroid gland were performed in 150 subjects with normal serum thyrotropin (TSH, thyroid-stimulating hormone) and free thyroxine (fT4) levels (63 men and 87 women, age range: 17 to 71 y). In each subject, the volume of both thyroid lobes was measured by 3-D ultrasound. On 2-D ultrasound, the craniocaudal (CC), lateromedial (LM) and anteroposterior (AP) dimensions of the thyroid lobes were measured. The equation was derived by correlating the volume of the thyroid lobes measured with 3-D ultrasound and the product of the three dimensions measured with 2-D ultrasound using linear regression analysis, in 75 subjects without thyroid nodule. The accuracy of thyroid volume estimation of the new equation and the three previously reported equations was evaluated and compared in another 75 subjects (without thyroid nodule, n = 30; with thyroid nodule, n = 45). It is suggested that volume of thyroid lobe may be estimated as: volume of thyroid lobe = 0.38.(CC.LM.AP) + 1.76. Result showed that the new equation (16.9% to 36.1%) had a significantly smaller thyroid volume estimation error than the previously reported equations (20.8% to 54.9%) (p thyroid volume estimation error when thyroid glands with nodules were examined (p thyroid volume equation, 2-D ultrasound can be a useful alternative in thyroid volume measurement when 3-D ultrasound is not available.

  17. Adrenal gland volume measurement in septic shock and control patients: a pilot study

    Energy Technology Data Exchange (ETDEWEB)

    Nougaret, Stephanie; Aufort, S.; Gallix, B. [Hopital Saint Eloi, Department of Abdominal Imaging, CHU Montpellier, Montpellier, Cedex 5 (France); Jung, B.; Chanques, G.; Jaber, S. [Hopital Saint Eloi, Intensive Care Unit, Department of Critical Care and Anesthesiology: DAR B, CHU Montpellier, Montpellier, Cedex 5 (France)

    2010-10-15

    To compare adrenal gland volume in septic shock patients and control patients by using semi-automated volumetry. Adrenal gland volume and its inter-observer variability were measured with tomodensitometry using semi-automated software in 104 septic shock patients and in 40 control patients. The volumes of control and septic shock patients were compared and the relationship between volume and outcome in intensive care was studied. The mean total volume of both adrenal glands was 7.2 {+-} 2.0 cm{sup 3} in control subjects and 13.3 {+-} 4.7 cm{sup 3} for total adrenal gland volume in septic shock patients (p < 0.0001). Measurement reproducibility was excellent with a concordance correlation coefficient value of 0.87. The increasing adrenal gland volume was associated with a higher rate of survival in intensive care. The present study reports that with semi-automated software, adrenal gland volume can be measured easily and reproducibly. Adrenal gland volume was found to be nearly double in sepsis compared with control patients. The absence of increased volume during sepsis would appear to be associated with a higher rate of mortality and may represent a prognosis factor which may help the clinician to guide their strategy. (orig.)

  18. THE CHANDRA LOCAL VOLUME SURVEY: THE X-RAY POINT-SOURCE POPULATION OF NGC 404

    Energy Technology Data Exchange (ETDEWEB)

    Binder, B.; Williams, B. F.; Weisz, D. R. [University of Washington, Department of Astronomy, Box 351580, Seattle, WA 98195 (United States); Eracleous, M. [Department of Astronomy and Astrophysics and Center for Gravitational Wave Physics, The Pennsylvania State University, 525 Davey Lab, University Park, PA 16802 (United States); Gaetz, T. J. [Harvard-Smithsonian Center for Astrophysics, 60 Garden Street Cambridge, MA 02138 (United States); Kong, A. K. H. [Institute of Astronomy and Department of Physics, National Tsing Hua University, Hsinchu 30013, Taiwan (China); Skillman, E. D. [University of Minnesota, Astronomy Department, 116 Church St. SE, Minneapolis, MN 55455 (United States)

    2013-02-15

    We present a comprehensive X-ray point-source catalog of NGC 404 obtained as part of the Chandra Local Volume Survey. A new 97 ks Chandra ACIS-S observation of NGC 404 was combined with archival observations for a total exposure of {approx}123 ks. Our survey yields 74 highly significant X-ray point sources and is sensitive to a limiting unabsorbed luminosity of {approx}6 Multiplication-Sign 10{sup 35} erg s{sup -1} in the 0.35-8 keV band. To constrain the nature of each X-ray source, cross-correlations with multi-wavelength data were generated. We searched overlapping Hubble Space Telescope observations for optical counterparts to our X-ray detections, but find only two X-ray sources with candidate optical counterparts. We find 21 likely low-mass X-ray binaries (LMXBs), although this number is a lower limit due to the difficulties in separating LMXBs from background active galactic nuclei. The X-ray luminosity functions (XLFs) in both the soft and hard energy bands are presented. The XLFs in the soft band (0.5-2 keV) and the hard band (2-8 keV) have a limiting luminosity at the 90% completeness limit of 10{sup 35} erg s{sup -1} and 10{sup 36} erg s{sup -1}, respectively, significantly lower than previous X-ray studies of NGC 404. We find the XLFs to be consistent with those of other X-ray populations dominated by LMXBs. However, the number of luminous (>10{sup 37} erg s{sup -1}) X-ray sources per unit stellar mass in NGC 404 is lower than is observed for other galaxies. The relative lack of luminous XRBs may be due to a population of LMXBs with main-sequence companions formed during an epoch of elevated star formation {approx}0.5 Gyr ago.

  19. Spam Source Clustering by Constructing Spammer Network with Correlation Measure

    Science.gov (United States)

    Shin, Jeongkyu; Kim, Seunghwan

    Spam filtering is one of the most challenging problems in electric message systems. In general, recent studies on specifying real spam source are based on content filtering because spammers usually falsify their origin. We propose a method to specify spam source based on structural analysis with complex network. We assume that each spam sources either has the same victim list or uses the same spam-hosting program. We treat spam source - target relationship as a bipartite network and construct weighted spam source network by network projection using correlation measure. We find that community clustering methods are inappropriate with spammer network. We group spammers with gradient-based grouping, which uses correlations between nodes as gradient between nodes. We convert them into local minima, which helps to cluster spammers into a few spam source groups. We investigate the weblog spam data with the proposed method and validate it. The method that we propose can be applied to diverse categorization problems, such as multiple text categorization and network subunit clustering.

  20. Environmental Toxicology: A Guide to Information Sources. Volume 7 in the "Man and the Environment Information Guide" Series.

    Science.gov (United States)

    Rudd, Robert L.

    This annotated bibliography on environmental toxicology brings together a diverse set of information sources from the physical, social, and natural sciences. These sources include periodical literature, government documents, scientific journals, and teaching materials. The volume is divided into sixteen sections organized into four parts: (1)…

  1. Semiautomatic regional segmentation to measure orbital fat volumes in thyroid-associated ophthalmopathy. A validation study.

    Science.gov (United States)

    Comerci, M; Elefante, A; Strianese, D; Senese, R; Bonavolontà, P; Alfano, B; Bonavolontà, B; Brunetti, A

    2013-08-01

    This study was designed to validate a novel semi-automated segmentation method to measure regional intra-orbital fat tissue volume in Graves' ophthalmopathy. Twenty-four orbits from 12 patients with Graves' ophthalmopathy, 24 orbits from 12 controls, ten orbits from five MRI study simulations and two orbits from a digital model were used. Following manual region of interest definition of the orbital volumes performed by two operators with different levels of expertise, an automated procedure calculated intra-orbital fat tissue volumes (global and regional, with automated definition of four quadrants). In patients with Graves' disease, clinical activity score and degree of exophthalmos were measured and correlated with intra-orbital fat volumes. Operator performance was evaluated and statistical analysis of the measurements was performed. Accurate intra-orbital fat volume measurements were obtained with coefficients of variation below 5%. The mean operator difference in total fat volume measurements was 0.56%. Patients had significantly higher intra-orbital fat volumes than controls (p<0.001 using Student's t test). Fat volumes and clinical score were significantly correlated (p<0.001). The semi-automated method described here can provide accurate, reproducible intra-orbital fat measurements with low inter-operator variation and good correlation with clinical data.

  2. Measurement of transplanted pancreatic volume using computed tomography: reliability by intra- and inter-observer variability

    Energy Technology Data Exchange (ETDEWEB)

    Lundqvist, Eva; Segelsjoe, Monica; Magnusson, Anders [Uppsala Univ., Dept. of Radiology, Oncology and Radiation Science, Section of Radiology, Uppsala (Sweden)], E-mail: eva.lundqvist.8954@student.uu.se; Andersson, Anna; Biglarnia, Ali-Reza [Dept. of Surgical Sciences, Section of Transplantation Surgery, Uppsala Univ. Hospital, Uppsala (Sweden)

    2012-11-15

    Background Unlike other solid organ transplants, pancreas allografts can undergo a substantial decrease in baseline volume after transplantation. This phenomenon has not been well characterized, as there are insufficient data on reliable and reproducible volume assessments. We hypothesized that characterization of pancreatic volume by means of computed tomography (CT) could be a useful method for clinical follow-up in pancreas transplant patients. Purpose To evaluate the feasibility and reliability of pancreatic volume assessment using CT scan in transplanted patients. Material and Methods CT examinations were performed on 21 consecutive patients undergoing pancreas transplantation. Volume measurements were carried out by two observers tracing the pancreatic contours in all slices. The observers performed the measurements twice for each patient. Differences in volume measurement were used to evaluate intra- and inter-observer variability. Results The intra-observer variability for the pancreatic volume measurements of Observers 1 and 2 was found to be in almost perfect agreement, with an intraclass correlation coefficient (ICC) of 0.90 (0.77-0.96) and 0.99 (0.98-1.0), respectively. Regarding inter-observer validity, the ICCs for the first and second measurements were 0.90 (range, 0.77-0.96) and 0.95 (range, 0.85-0.98), respectively. Conclusion CT volumetry is a reliable and reproducible method for measurement of transplanted pancreatic volume.

  3. Accuracy of MRI volume measurements of breast lesions: comparison between automated, semiautomated and manual assessment

    Energy Technology Data Exchange (ETDEWEB)

    Rominger, Marga B.; Fournell, Daphne; Nadar, Beenarose Thanka; Figiel, Jens H.; Keil, Boris; Heverhagen, Johannes T. [Philipps University, Department of Radiology, Marburg (Germany); Behrens, Sarah N.M. [MeVis GmbH, Bremen (Germany)

    2009-05-15

    The aim of this study was to investigate the efficacy of a dedicated software tool for automated and semiautomated volume measurement in contrast-enhanced (CE) magnetic resonance mammography (MRM). Ninety-six breast lesions with histopathological workup (27 benign, 69 malignant) were re-evaluated by different volume measurement techniques. Volumes of all lesions were extracted automatically (AVM) and semiautomatically (SAVM) from CE 3D MRM and compared with manual 3D contour segmentation (manual volume measurement, MVM, reference measurement technique) and volume estimates based on maximum diameter measurement (MDM). Compared with MVM as reference method MDM, AVM and SAVM underestimated lesion volumes by 63.8%, 30.9% and 21.5%, respectively, with significantly different accuracy for benign (102.4%, 18.4% and 11.4%) and malignant (54.9%, 33.0% and 23.1%) lesions (p<0.05). Inter- and intraobserver reproducibility was best for AVM (mean difference {+-}2SD, 1.0{+-}9.7% and 1.8{+-}12.1%) followed by SAVM (4.3{+-}25.7% and 4.3{+-}7.9%), MVM (2.3{+-}38.2% and 8.6{+-}31.8%) and MDM (33.9{+-}128.4% and 9.3{+-}55.9%). SAVM is more accurate for volume assessment of breast lesions than MDM and AVM. Volume measurement is less accurate for malignant than benign lesions. (orig.)

  4. Source appointment of fine particle number and volume concentration during severe haze pollution in Beijing in January 2013.

    Science.gov (United States)

    Liu, Zirui; Wang, Yuesi; Hu, Bo; Ji, Dongsheng; Zhang, Junke; Wu, Fangkun; Wan, Xin; Wang, Yonghong

    2016-04-01

    Extreme haze episodes repeatedly shrouded Beijing during the winter of 2012-2013, causing major environmental and health problems. To better understand these extreme events, particle number size distribution (PNSD) and particle chemical composition (PCC) data collected in an intensive winter campaign in an urban site of Beijing were used to investigate the sources of ambient fine particles. Positive matrix factorization (PMF) analysis resolved a total of eight factors: two traffic factors, combustion factors, secondary aerosol, two accumulation mode aerosol factors, road dust, and long-range transported (LRT) dust. Traffic emissions (54%) and combustion aerosol (27%) were found to be the most important sources for particle number concentration, whereas combustion aerosol (33%) and accumulation mode aerosol (37%) dominated particle volume concentrations. Chemical compositions and sources of fine particles changed dynamically in the haze episodes. An enhanced role of secondary inorganic species was observed in the formation of haze pollution. Regional transport played an important role for high particles, contribution of which was on average up to 24-49% during the haze episodes. Secondary aerosols from urban background presented the largest contributions (45%) for the rapid increase of fine particles in the severest haze episode. In addition, the invasion of LRT dust aerosols further elevated the fine particles during the extreme haze episode. Our results showed a clear impact of regional transport on the local air pollution, suggesting the importance of regional-scale emission control measures in the local air quality management of Beijing.

  5. A Cosmic Bell Test with Measurement Settings from Astronomical Sources

    CERN Document Server

    Handsteiner, Johannes; Rauch, Dominik; Gallicchio, Jason; Liu, Bo; Hosp, Hannes; Kofler, Johannes; Bricher, David; Fink, Matthias; Leung, Calvin; Mark, Anthony; Nguyen, Hien T; Sanders, Isabella; Steinlechner, Fabian; Ursin, Rupert; Wengerowsky, Sören; Guth, Alan H; Kaiser, David I; Scheidl, Thomas; Zeilinger, Anton

    2016-01-01

    Bell's theorem states that some predictions of quantum mechanics cannot be reproduced by a local-realist theory. That conflict is expressed by Bell's inequality, which is usually derived under the assumption that there are no statistical correlations between the choices of measurement settings and anything else that can causally affect the measurement outcomes. In previous experiments, this "freedom of choice" was addressed by ensuring that selection of measurement settings via conventional "quantum random number generators" (QRNGs) was space-like separated from the entangled particle creation. This, however, left open the possibility that an unknown cause affected both the setting choices and measurement outcomes as recently as mere microseconds before each experimental trial. Here we report on a new experimental test of Bell's inequality that, for the first time, uses distant astronomical sources as "cosmic setting generators." In our tests with polarization-entangled photons, measurement settings were chos...

  6. Reliability and validity of the lung volume measurement made by the BOD POD body composition system.

    Science.gov (United States)

    Davis, James A; Dorado, Silvia; Keays, Kathleen A; Reigel, Kimberly A; Valencia, Kristoffer S; Pham, Patrick H

    2007-01-01

    The BOD POD Body Composition System uses air-displacement plethysmography to measure body volume. To correct the body volume measurement for the subject's lung volume, the BOD POD utilizes pulmonary plethysmography to measure functional residual capacity (FRC) at mid-exhalation as that is the subject's lung volume during the body volume measurement. Normally, FRC is measured at end-exhalation. The BOD POD FRC measurement can be corrected to an end-exhalation volume by subtracting approximately one-half of the measured tidal volume. Our purpose was to determine the reliability and validity of the BOD POD FRC measurement at end-exhalation. Ninety-two healthy adults (half female) underwent duplicate FRC measurements by the BOD POD and one FRC measurement by a traditional gas dilution technique. The latter method was used as the reference method for the validity component of the study. The order of the FRC measurements by the two methods was randomized. The test-retest correlation coefficients for the duplicate BOD POD FRC measurements for the male and female subjects were 0.966 and 0.948, respectively. The mean differences between the BOD POD FRC trial #1 measurement and gas dilution FRC measurement for the male and female subjects were -32 and -23 ml, respectively. Neither difference was statistically significant. The correlation coefficients for these two measurements in the male and female subjects were 0.925 and 0.917, respectively. Based on these results, we conclude that the BOD POD FRC measurement in healthy males and females is both reliable and valid.

  7. Blood volume measurements in gopher snakes, using autologous 51Cr-labeled red blood cells.

    Science.gov (United States)

    Smeller, J M; Bush, M; Seal, U S

    1978-02-01

    Blood volume determinations were performed in 5 anesthetized gopher snakes (Pituophis melanoleucus catenifer) by means of a 51Cr-labeled red blood cell (RBC) method. The mean blood volume was 52.8 ml/kg of body weight (+/- 6.21 SE). Previous blood volume measurements have not been reported for this species. The RBC survival rate was estimated to be greater than 660 days. The RBC survival rate is long, but it cannot be determined accurately by this method.

  8. Numerical study of cesium effects on negative ion production in volume sources

    Energy Technology Data Exchange (ETDEWEB)

    Fukumasa, Osamu; Niitani, Eiji [Yamaguchi Univ., Ube (Japan). Faculty of Engineering

    1997-02-01

    Effects of cesium vapor injection of H{sup -} production in a tandem negative ion source are studied numerically as a function of plasma parameters. Model calculation is done by solving a set of particle balance equations in a steady-state hydrogen discharge plasmas. Here, the results which focus on gas pressure and electron temperature dependences of H{sup -} volume production are presented and discussed. With including H{sup -} surface production processes caused by both H atoms and positive hydrogen ions, enhancement of H{sup -} production and pressure dependence of H{sup -} production observed experimentally are well reproduced in the model. To enhance H{sup -} production, however, so-called electron cooling is not so effective if plasma parameters are initially optimized with the use of magnetic filter. (author)

  9. Monte Carlo method with heuristic adjustment for irregularly shaped food product volume measurement.

    Science.gov (United States)

    Siswantoro, Joko; Prabuwono, Anton Satria; Abdullah, Azizi; Idrus, Bahari

    2014-01-01

    Volume measurement plays an important role in the production and processing of food products. Various methods have been proposed to measure the volume of food products with irregular shapes based on 3D reconstruction. However, 3D reconstruction comes with a high-priced computational cost. Furthermore, some of the volume measurement methods based on 3D reconstruction have a low accuracy. Another method for measuring volume of objects uses Monte Carlo method. Monte Carlo method performs volume measurements using random points. Monte Carlo method only requires information regarding whether random points fall inside or outside an object and does not require a 3D reconstruction. This paper proposes volume measurement using a computer vision system for irregularly shaped food products without 3D reconstruction based on Monte Carlo method with heuristic adjustment. Five images of food product were captured using five cameras and processed to produce binary images. Monte Carlo integration with heuristic adjustment was performed to measure the volume based on the information extracted from binary images. The experimental results show that the proposed method provided high accuracy and precision compared to the water displacement method. In addition, the proposed method is more accurate and faster than the space carving method.

  10. Evaluation of Anterior Chamber Volume in Cataract Patients with Swept-Source Optical Coherence Tomography.

    Science.gov (United States)

    He, Wenwen; Zhu, Xiangjia; Wolff, Don; Zhao, Zhennan; Sun, Xinghuai; Lu, Yi

    2016-01-01

    Purpose. To evaluate the anterior chamber volume in cataract patients with Swept-Source Optical Coherence Tomography (SS-OCT) and its influencing factors. Methods. Anterior chamber volume of 92 cataract patients was evaluated with SS-OCT in this cross-sectional study. Univariate analyses and multiple linear regression were used to investigate gender, age, operated eye, posterior vitreous detachment, lens opacity grading, and axial length (AXL) related variables capable of influencing the ACV. Results. The average ACV was 139.80 ± 38.21 mm(3) (range 59.41 to 254.09 mm(3)). The average ACV was significantly larger in male patients than in female patients (P = 0.001). ACV was negatively correlated with age and LOCS III cortical (C) grading of the lens (Pearson's correlation analysis, r = -0.443, P ACV was also increased with AXL (Pearson's correlation analysis, r = 0.552, P ACV (F = 10.252  P ACV varied significantly among different subjects. Influencing factors that contribute to reduced ACV were female gender, increased age, LOCS III C grade, and shorter AXL.

  11. Generalized source Finite Volume Method for radiative transfer equation in participating media

    Science.gov (United States)

    Zhang, Biao; Xu, Chuan-Long; Wang, Shi-Min

    2017-03-01

    Temperature monitoring is very important in a combustion system. In recent years, non-intrusive temperature reconstruction has been explored intensively on the basis of calculating arbitrary directional radiative intensities. In this paper, a new method named Generalized Source Finite Volume Method (GSFVM) was proposed. It was based on radiative transfer equation and Finite Volume Method (FVM). This method can be used to calculate arbitrary directional radiative intensities and is proven to be accurate and efficient. To verify the performance of this method, six test cases of 1D, 2D, and 3D radiative transfer problems were investigated. The numerical results show that the efficiency of this method is close to the radial basis function interpolation method, but the accuracy and stability is higher than that of the interpolation method. The accuracy of the GSFVM is similar to that of the Backward Monte Carlo (BMC) algorithm, while the time required by the GSFVM is much shorter than that of the BMC algorithm. Therefore, the GSFVM can be used in temperature reconstruction and improvement on the accuracy of the FVM.

  12. Hanford 67-series: a volume of atmospheric field diffusion measurements

    Energy Technology Data Exchange (ETDEWEB)

    Nickola, P.W.

    1977-11-01

    This volume documents atmospheric diffusion experiments carried out at the Hanford reservation during the period 1967 to 1973. A total of 103 tracer releases during 54 release periods is tabulated. Multi-tracer releases (generally from different elevations) were made during most of the experimental periods. Release heights varied from ground level to an elevation of 111 m. Tracers were sampled simultaneously on as many as 10 arcs at distances of up to 12.8 km from the tracer release point. As many as 718 field sampling locations were employed during some of the experiments. Vertical profiles of concentration were monitored on towers during 23 of the 54 release periods. Concurrent vertical profiles of mean temperature, of mean wind speed and direction, and of direction standard deviation are also tabled for elevations up to 122 m.

  13. Dedicated breast CT: Fibroglandular volume measurements in a diagnostic population

    Energy Technology Data Exchange (ETDEWEB)

    Vedantham, Srinivasan; Shi Linxi; Karellas, Andrew; O' Connell, Avice M. [Department of Radiology, University of Massachusetts Medical School, Worcester, Massachusetts 01655 (United States); Department of Imaging Sciences, University of Rochester Medical Center, Rochester, New York 14642 (United States)

    2012-12-15

    Purpose: To determine the mean and range of volumetric glandular fraction (VGF) of the breast in a diagnostic population using a high-resolution flat-panel cone-beam dedicated breast CT system. This information is important for Monte Carlo-based estimation of normalized glandular dose coefficients and for investigating the dependence of VGF on breast dimensions, race, and pathology. Methods: Image data from a clinical trial investigating the role of dedicated breast CT that enrolled 150 women were retrospectively analyzed to determine the VGF. The study was conducted in adherence to a protocol approved by the institutional human subjects review boards and written informed consent was obtained from all study participants. All participants in the study were assigned BI-RADS{sup Registered-Sign} 4 or 5 as per the American College of Radiology assessment categories after standard diagnostic work-up and underwent dedicated breast CT exam prior to biopsy. A Gaussian-kernel based fuzzy c-means algorithm was used to partition the breast CT images into adipose and fibroglandular tissue after segmenting the skin. Upon determination of the accuracy of the algorithm with a phantom, it was applied to 137 breast CT volumes from 136 women. VGF was determined for each breast and the mean and range were determined. Pathology results with classification as benign, malignant, and hyperplasia were available for 132 women, and were used to investigate if the distributions of VGF varied with pathology. Results: The algorithm was accurate to within {+-}1.9% in determining the volume of an irregular shaped phantom. The study mean ({+-} inter-breast SD) for the VGF was 0.172 {+-} 0.142 (range: 0.012-0.719). VGF was found to be negatively correlated with age, breast dimensions (chest-wall to nipple length, pectoralis to nipple length, and effective diameter at chest-wall), and total breast volume, and positively correlated with fibroglandular volume. Based on pathology, pairwise statistical

  14. Dispersion Measure Variation of Repeating Fast Radio Burst Sources

    Science.gov (United States)

    Yang, Yuan-Pei; Zhang, Bing

    2017-09-01

    The repeating fast radio burst (FRB) 121102 was recently localized in a dwarf galaxy at a cosmological distance. The dispersion measure (DM) derived for each burst from FRB 121102 so far has not shown significant evolution, even though an apparent increase was recently seen with newly detected VLA bursts. It is expected that more repeating FRB sources may be detected in the future. In this work, we investigate a list of possible astrophysical processes that might cause DM variation of a particular FRB source. The processes include (1) cosmological scale effects such as Hubble expansion and large-scale structure fluctuations; (2) FRB local effects such as gas density fluctuation, expansion of a supernova remnant (SNR), a pulsar wind nebula, and an H ii region; and (3) the propagation effect due to plasma lensing. We find that the DM variations contributed by the large-scale structure are extremely small, and any observable DM variation is likely caused by the plasma local to the FRB source. In addition to mechanisms that decrease DM over time, we suggest that an FRB source in an expanding SNR around a nearly neutral ambient medium during the deceleration (Sedov–Taylor and snowplow) phases or in a growing H ii region can increase DM. Some effects (e.g., an FRB source moving in an H ii region or plasma lensing) can produce either positive or negative DM variations. Future observations of DM variations of FRB 121102 and other repeating FRB sources can provide important clues regarding the physical origin of these sources.

  15. Feasibility of the left ventricular volume measurement by acoustic quantification method. Comparison with ultrafast computed tomography

    Energy Technology Data Exchange (ETDEWEB)

    Tomimoto, Shigehiro; Nakatani, Satoshi; Tanaka, Norio; Uematsu, Masaaki; Beppu, Shintaro; Nagata, Seiki; Hamada, Seiki; Takamiya, Makoto; Miyatake, Kunio [National Cardiovascular Center, Suita, Osaka (Japan)

    1995-01-01

    Acoustic quantification (AQ: the real-time automated boundary detection system) allows instantaneous measurement of cardiac chamber volumes. The feasibility of this method was evaluated by comparing the left ventricular (LV) volumes obtained with AQ to those derived from ultrafast computed tomography (UFCT), which enables accurate measurements of LV volumes even in the presence of LV asynergy, in 23 patients (8 with ischemic heart disease, 5 with cardiomyopathy, 3 with valvular heart disease). Both LV end-diastolic and end-systolic volumes obtained with the AQ method were in good agreement with those obtained with UFCT (y=1.04{chi}-16.9, r=0.95; y=0.87{chi}+15.7, r=0.91; respectively). AQ was reliable even in the presence of LV asynergy. Interobserver variability for the AQ measurement was 10.2%. AQ provides a new, clinically useful method for real-time accurate estimation of the left ventricular volume. (author).

  16. Effective shielding to measure beam current from an ion source

    Energy Technology Data Exchange (ETDEWEB)

    Bayle, H., E-mail: bayle@bergoz.com [Bergoz Instrumentation, Saint-Genis-Pouilly (France); Delferrière, O.; Gobin, R.; Harrault, F.; Marroncle, J.; Senée, F.; Simon, C.; Tuske, O. [CEA, Saclay (France)

    2014-02-15

    To avoid saturation, beam current transformers must be shielded from solenoid, quad, and RFQ high stray fields. Good understanding of field distribution, shielding materials, and techniques is required. Space availability imposes compact shields along the beam pipe. This paper describes compact effective concatenated magnetic shields for IFMIF-EVEDA LIPAc LEBT and MEBT and for FAIR Proton Linac injector. They protect the ACCT Current Transformers beyond 37 mT radial external fields. Measurements made at Saclay on the SILHI source are presented.

  17. Practical do-it-yourself device for accurate volume measurement of breast.

    Science.gov (United States)

    Tezel, E; Numanoğlu, A

    2000-03-01

    A simple and accurate method of measuring differences in breast volume based on Archimedes' principle is described. In this method, a plastic container is placed on the breast of the patient who is lying in supine position. While the breast occupies part of the container, the remaining part is filled with water and the volume is measured. This method allows the measurement of the volume differences of asymmetric breasts and also helps the surgeon to estimate the size of the prosthesis to be used in augmentation mammaplasty.

  18. Recent Developments in Using Measured Sources in Computational EMC

    DEFF Research Database (Denmark)

    Sørensen, Morten; Franek, Ondrej; Pedersen, Gert F.

    2015-01-01

    This paper gives an overview of the recent developments in using near-field scanning for proactive EMC work. The aim is to use measured near fields as a source for simulations in order to predict radiated emission from printed circuit boards placed in a product. Far fields were predicted based...... on only H-fields on the top and bottom surface on a Huygens’ box surrounding the board. Simulation of a simple board with microstrips and measurements of a complicated signal board were used to evaluate the proposed method....

  19. Recent Developments in Using Measured Sources in Computational EMC

    DEFF Research Database (Denmark)

    Sørensen, Morten; Franek, Ondrej; Pedersen, Gert F.

    2015-01-01

    This paper gives an overview of the recent developments in using near-field scanning for proactive EMC work. The aim is to use measured near fields as a source for simulations in order to predict radiated emission from printed circuit boards placed in a product. Far fields were predicted based...... on only H-fields on the top and bottom surface on a Huygens’ box surrounding the board. Simulation of a simple board with microstrips and measurements of a complicated signal board were used to evaluate the proposed method....

  20. Error Sources in the ETA Energy Analyzer Measurement

    Energy Technology Data Exchange (ETDEWEB)

    Nexsen, W E

    2004-12-13

    At present the ETA beam energy as measured by the ETA energy analyzer and the DARHT spectrometer differ by {approx}12%. This discrepancy is due to two sources, an overestimate of the effective length of the ETA energy analyzer bending-field, and data reduction methods that are not valid. The discrepancy can be eliminated if we return to the original process of measuring the angular deflection of the beam and use a value of 43.2cm for the effective length of the axial field profile.

  1. Variation in Measurements of Transtibial Stump Model Volume A Comparison of Five Methods

    NARCIS (Netherlands)

    Bolt, A.; de Boer-Wilzing, V. G.; Geertzen, J. H. B.; Emmelot, C. H.; Baars, E. C. T.; Dijkstra, P. U.

    2010-01-01

    Objective: To determine the right moment for fitting the first prosthesis, it is necessary to know when the volume of the stump has stabilized. The aim of this study is to analyze variation in measurements of transtibial stump model volumes using the water immersion method, the Design TT system, the

  2. Measuring External Sources of Background (R&D) at Homestake

    Science.gov (United States)

    Mei, Dongming; Chan, Yuen-Dat; Elliott, Steve; Gray, Frederick; Keller, Christina; Sun, Yongchen

    2008-04-01

    Measuring external sources of radioactivity at the DUSEL site is the key to success in low-energy neutrino and dark matter (WIMP searches) experiments. Natural radioactivity can be measured using germanium and NaI detectors. Muon-induced neutrons and (a,n) neutrons will be measured utilizing liquid scintillators and germanium detectors through the 72Ge(n,nxe) reaction. External sources of background, particularly fast neutrons and cosmogenic radioactivity from muon-induced processes, are background matter that must be eliminated for underground experiments in pursuit of double beta decay, WIMPs, and oscillations of low-energy neutrinos. However, muon-induced neutron production rates with heavy elements, such as lead and copper, are not well understood. The discrepancy between the measurements and FLUKA simulations is as large as about a factor of 3. This discrepancy needs be understood for the muon- induced fast neutron production rate in lead and copper, which are the most popular materials for shielding underground experiments. We propose an experiment at 300-ft level to measure the muon-induced fast neutron production rate in different targets.

  3. Measuring stone volume - three-dimensional software reconstruction or an ellipsoid algebra formula?

    Science.gov (United States)

    Finch, William; Johnston, Richard; Shaida, Nadeem; Winterbottom, Andrew; Wiseman, Oliver

    2014-04-01

    To determine the optimal method for assessing stone volume, and thus stone burden, by comparing the accuracy of scalene, oblate, and prolate ellipsoid volume equations with three-dimensional (3D)-reconstructed stone volume. Kidney stone volume may be helpful in predicting treatment outcome for renal stones. While the precise measurement of stone volume by 3D reconstruction can be accomplished using modern computer tomography (CT) scanning software, this technique is not available in all hospitals or with routine acute colic scanning protocols. Therefore, maximum diameters as measured by either X-ray or CT are used in the calculation of stone volume based on a scalene ellipsoid formula, as recommended by the European Association of Urology. In all, 100 stones with both X-ray and CT (1-2-mm slices) were reviewed. Complete and partial staghorn stones were excluded. Stone volume was calculated using software designed to measure tissue density of a certain range within a specified region of interest. Correlation coefficients among all measured outcomes were compared. Stone volumes were analysed to determine the average 'shape' of the stones. The maximum stone diameter on X-ray was 3-25 mm and on CT was 3-36 mm, with a reasonable correlation (r = 0.77). Smaller stones (15 mm towards scalene ellipsoids. There was no difference in stone shape by location within the kidney. As the average shape of renal stones changes with diameter, no single equation for estimating stone volume can be recommended. As the maximum diameter increases, calculated stone volume becomes less accurate, suggesting that larger stones have more asymmetric shapes. We recommend that research looking at stone clearance rates should use 3D-reconstructed stone volumes when available, followed by prolate, oblate, or scalene ellipsoid formulas depending on the maximum stone diameter. © 2013 The Authors. BJU International © 2013 BJU International.

  4. Molar Volume Analysis of Molten Ni-Al-Co Alloy by Measuring the Density

    Institute of Scientific and Technical Information of China (English)

    XIAO Feng; FANG Liang; FU Yuechao; YANG Lingchuan

    2004-01-01

    The density of molten Ni-Al-Co alloys was measured in the temperature range of 1714~1873K using a modified pycnometric method, and the molar volume of molten alloys was analyzed. The density of molten Ni-Al-Co alloys was found to decrease with increasing temperature and Co concentration in alloys. The molar volume of molten Ni-Al-Co alloys increases with increasing Co concentration in alloys. The molar volume of molten Ni-Al-Co alloys shows a negative deviation from the linear molar volume.

  5. Source regions for atmospheric aerosol measured at Barrow, Alaska.

    Science.gov (United States)

    Polissar, A V; Hopke, P K; Harris, J M

    2001-11-01

    Aerosol data consisting of condensation nuclei (CN) counts, black carbon (BC) mass concentration, and aerosol light scattering coefficient at the wavelength of 450 nm (SC) measured at Barrow, AK, from 1986 to 1997 have been analyzed. BC and SC show an annual cycle with the Arctic haze maxima in the winter and spring and the minima in the summer. The CN time series shows two maxima in March and August. Potential source contribution function (PSCF) that combines the aerosol data with air parcel backward trajectories was applied to identify potential source areas and the preferred pathways that give rise to the observed high aerosol concentrations at Barrow. Ten-day isentropic back trajectories arriving twice daily at 500 and 1500 m above sea level were calculated for the period from 1986 to 1997. The PSCF analyses were performed based on the 80th percentile criterion values for the 2- and 24-h averages of the measured aerosol parameters. There was a good correspondence between PSCF maps for the 2- and 24-h averages, indicating that 1-day aerosol sampling in the Arctic adequately represents the aerosol source areas. In winter, the high PSCF values for BC and SC are related to industrial source areas in Eurasia. The trajectory domain in winter and spring is larger than in summer, reflecting weaker transport in summer. No high PSCF areas for BC and SC can be observed in summer. The result is related to the poor transport into the Arctic plus the strong removal of aerosol by precipitation in summer. In contrast to the BC and SC maps, the CN plot for summer shows high PSCF areas in the North Pacific Ocean. High CN values appearto be mostly connected with the long-range transport from Eurasia in winter and spring and with the reduced sulfur compound emission from biogenic activities in the ocean in the summer. PSCF analysis was found to be effective in identifying potential aerosol source areas.

  6. Light-assisted drying (LAD) of small volume biologics: a comparison of two IR light sources

    Science.gov (United States)

    Young, Madison A.; Van Vorst, Matthew; Elliott, Gloria D.; Trammell, Susan R.

    2016-03-01

    Protein therapeutics have been developed to treat diseases ranging from arthritis and psoriasis to cancer. A challenge in the development of protein-based drugs is maintaining the protein in the folded state during processing and storage. We are developing a novel processing method, light-assisted drying (LAD), to dehydrate proteins suspended in a sugar (trehalose) solution for storage at supra-zero temperatures. Our technique selectively heats the water in small volume samples using near-IR light to speed dehydration which prevents sugar crystallization that can damage embedded proteins. In this study, we compare the end moisture content (EMC) as a function of processing time of samples dried with two different light sources, Nd:YAG (1064 nm) and Thulium fiber (1850 nm) lasers. EMC is the ratio of water to dry weight in a sample and the lower the EMC the higher the possible storage temperature. LAD with the 1064 and 1850 nm lasers yielded 78% and 65% lower EMC, respectively, than standard air-drying. After 40 minutes of LAD with 1064 and 1850 nm sources, EMCs of 0.27+/-.27 and 0.15+/-.05 gH2O/gDryWeight were reached, which are near the desired value of 0.10 gH2O/gDryWeight that enables storage in a glassy state without refrigeration. LAD is a promising new technique for the preparation of biologics for anhydrous preservation.

  7. Environmental effects of energy production and utilization in the U. S. Volume I. Sources, trends, and costs of control

    Energy Technology Data Exchange (ETDEWEB)

    Newkirk, H.W. (comp.)

    1976-05-01

    Volume I deals with sources (what the emissions are and where they come from), trends (quantities of emissions and their dispersion with time), and costs of control (what it takes in time, energy, and money to meet minimum standards). Volume II concerns itself with the public health effects of energy production and utilization. Volume III summarizes the various techniques for controlling emissions, technological as well as economic, social, and political. (For abstracts of Vols. II and III, see ERDA Energy Research Abstracts, Vol. 2, Absts. 5764 and 5670, respectively) Each volume is divided into sections dealing with the atmosphere, water, land, and social activities--each division indicating a particular sphere of man's environment affected by energy production and use. The sources of information that were used in this study included textbooks, journal articles, technical reports, memoranda, letters, and personal communications. These are cited in the text at the end of each subsection and on the applicable tables and figures.

  8. Spray ignition measurements in a constant volume combustion vessel under engine-relevant conditions

    Science.gov (United States)

    Ramesh, Varun

    Pressure-based and optical diagnostics for ignition delay (ID) measurement of a diesel spray from a multi-hole nozzle were investigated in a constant volume combustion vessel (CVCV) at conditions similar to those in a conventional diesel engine at the start of injection (SOI). It was first hypothesized that compared to an engine, the shorter ID in a CVCV was caused by NO, a byproduct of premixed combustion. The presence of a significant concentration of NO+NO2 was confirmed experimentally and by using a multi-zone model of premixed combustion. Experiments measuring the effect of NO on ID were performed at conditions relevant to a conventional diesel engine. Depending on the temperature regime and the nature of the fuel, NO addition was found to advance or retard ignition. Constant volume ignition simulations were capable of describing the observed trends; the magnitudes were different due to the physical processes involved in spray ignition, not modeled in the current study. The results of the study showed that ID is sensitive to low NO concentrations (<100 PPM) in the low-temperature regime. A second source of uncertainty in pressure-based ID measurement is the systematic error associated with the correction used to account for the speed of sound. Simultaneous measurements of volumetric OH chemiluminescence (OHC) and pressure during spray ignition found the OHC to closely resemble the pressure-based heat release rate for the full combustion duration. The start of OHC was always found to be shorter than the pressure-based ID for all fuels and conditions tested by 100 ms. Experiments were also conducted measuring the location and timing of high-temperature ignition and the steady-state lift-off length by high-speed imaging of OHC during spray ignition. The delay period calculated using the measured ignition location and the bulk average speed of sound was in agreement with the delay between OHC and the pressure-based ID. Results of the study show that start of OHC

  9. Mapping methane emission sources over California based on airborne measurements

    Science.gov (United States)

    Karl, T.; Guha, A.; Peischl, J.; Misztal, P. K.; Jonsson, H.; Goldstein, A. H.; Ryerson, T. B.

    2011-12-01

    The California Global Warming Solutions Act of 2006 (AB 32) has created a need to accurately characterize the emission sources of various greenhouse gases (GHGs) and verify the existing state GHG inventory. Methane (CH4) is a major GHG with a global warming potential of 20 times that of CO2 and currently constitutes about 6% of the total statewide GHG emissions on a CO2 equivalent basis. Some of the major methane sources in the state are area sources where methane is biologically produced (e.g. dairies, landfills and waste treatment plants) making bottom-up estimation of emissions a complex process. Other potential sources include fugitive emissions from oil extraction processes and natural gas distribution network, emissions from which are not well-quantified. The lack of adequate field measurement data to verify the inventory and provide independently generated estimates further contributes to the overall uncertainty in the CH4 inventory. In order to gain a better perspective of spatial distribution of major CH4 sources in California, a real-time measurement instrument based on Cavity Ring Down Spectroscopy (CRDS) was installed in a Twin Otter aircraft for the CABERNET (California Airborne BVOC Emissions Research in Natural Ecosystems Transects) campaign, where the driving research goal was to understand the spatial distribution of biogenic VOC emissions. The campaign took place in June 2011 and encompassed over forty hours of airborne CH4 and CO2 measurements during eight unique flights which covered much of the Central Valley and its eastern edge, the Sacramento-San Joaquin delta and the coastal range. The coincident VOC measurements, obtained through a high frequency proton transfer reaction mass spectrometer (PTRMS), aid in CH4 source identification. High mixing ratios of CH4 (> 2000 ppb) are observed consistently in all the flight transects above the Central Valley. These high levels of CH4 are accompanied by high levels of methanol which is an important

  10. Idaho field experiment 1981. Volume 2: measurement data

    Energy Technology Data Exchange (ETDEWEB)

    Start, G E; Sagendorf, J F; Ackermann, G R; Cate, J H; Hukari, N F; Dickson, C R

    1984-04-01

    The 1981 Idaho Field Experiment was conducted in southeastern Idaho over the upper Snake River Plain. Nine test-day case studies were conducted between July 15 and 30, 1981. Releases of SF/sub 6/ gaseous tracer were made for 8-hour periods from 46m above ground. Tracer was sampled hourly, for 12 sequential hours, at about 100 locations within an area 24km square. Also, a single total integrated sample of about 30 hours duration was collected at approximately 100 sites within an area 48 by 72km square (using 6km spacings). Extensive tower profiles of meteorology at the release point were collected. RAWINSONDES, RABALS and PIBALS were collected at 3 to 5 sites. Horizontal, low-altitude winds were monitored using the INEL MESONET. SF/sub 6/ tracer plume releases were marked with co-located oil fog releases and bi-hourly sequential launches of tetroon pairs. Aerial LIDAR observations of the oil fog plume and airborne samples of SF/sub 6/ were collected. High altitude aerial photographs of daytime plumes were collected. Volume II lists the data in tabular form or cites the special supplemental reports by other participating contractors. While the primary user file and the data archive are maintained on 9 track/1600 cpi magnetic tapes, listings of the individual values are provided for the user who either cannot utilize the tapes or wishes to preview the data. The accuracies and quality of these data are described.

  11. Mapping methane sources and emissions over California from direct airborne flux and VOC source tracer measurements

    Science.gov (United States)

    Guha, A.; Misztal, P. K.; Peischl, J.; Karl, T.; Jonsson, H. H.; Woods, R. K.; Ryerson, T. B.; Goldstein, A. H.

    2013-12-01

    Quantifying the contributions of methane (CH4) emissions from anthropogenic sources in the Central Valley of California is important for validation of the statewide greenhouse gas (GHG) inventory and subsequent AB32 law implementation. The state GHG inventory is largely based on activity data and emission factor based estimates. The 'bottom-up' emission factors for CH4 have large uncertainties and there is a lack of adequate 'top-down' measurements to characterize emission rates. Emissions from non-CO2 GHG sources display spatial heterogeneity and temporal variability, and are thus, often, poorly characterized. The Central Valley of California is an agricultural and industry intensive region with large concentration of dairies and livestock operations, active oil and gas fields and refining operations, as well as rice cultivation all of which are known CH4 sources. In order to gain a better perspective of the spatial distribution of major CH4 sources in California, airborne measurements were conducted aboard a Twin Otter aircraft for the CABERNET (California Airborne BVOC Emissions Research in Natural Ecosystems Transects) campaign, where the driving research goal was to understand the spatial distribution of biogenic VOC emissions. The campaign took place in June 2011 and encompassed over forty hours of low-altitude and mixed layer airborne CH4 and CO2 measurements alongside coincident VOC measurements. Transects during eight unique flights covered much of the Central Valley and its eastern edge, the Sacramento-San Joaquin delta and the coastal range. We report direct quantification of CH4 fluxes using real-time airborne Eddy Covariance measurements. CH4 and CO2 were measured at 1-Hz data rate using an instrument based on Cavity Ring Down Spectroscopy (CRDS) along with specific VOCs (like isoprene, methanol, acetone etc.) measured at 10-Hz using Proton Transfer Reaction Mass Spectrometer - Eddy Covariance (PTRMS-EC) flux system. Spatially resolved eddy covariance

  12. Neutron-emission measurements at a white neutron source

    Energy Technology Data Exchange (ETDEWEB)

    Haight, Robert C [Los Alamos National Laboratory

    2010-01-01

    Data on the spectrum of neutrons emittcd from neutron-induced reactions are important in basic nuclear physics and in applications. Our program studies neutron emission from inelastic scattering as well as fission neutron spectra. A ''white'' neutron source (continuous in energy) allows measurements over a wide range of neutron energies all in one experiment. We use the tast neutron source at the Los Alamos Neutron Science Center for incident neutron energies from 0.5 MeV to 200 MeV These experiments are based on double time-of-flight techniques to determine the energies of the incident and emitted neutrons. For the fission neutron measurements, parallel-plate ionization or avalanche detectors identify fission in actinide samples and give the required fast timing pulse. For inelastic scattering, gamma-ray detectors provide the timing and energy spectroscopy. A large neutron-detector array detects the emitted neutrons. Time-of-flight techniques are used to measure the energies of both the incident and emitted neutrons. Design considerations for the array include neutron-gamma discrimination, neutron energy resolution, angular coverage, segmentation, detector efficiency calibration and data acquisition. We have made preliminary measurements of the fission neutron spectra from {sup 235}U, {sup 238}U, {sup 237}Np and {sup 239}Pu. Neutron emission spectra from inelastic scattering on iron and nickel have also been investigated. The results obtained will be compared with evaluated data.

  13. A technique for fast and accurate measurement of hand volumes using Archimedes' principle.

    Science.gov (United States)

    Hughes, S; Lau, J

    2008-03-01

    A new technique for measuring hand volumes using Archimedes principle is described. The technique involves the immersion of a hand in a water container placed on an electronic balance. The volume is given by the change in weight divided by the density of water. This technique was compared with the more conventional technique of immersing an object in a container with an overflow spout and collecting and weighing the volume of overflow water. The hand volume of two subjects was measured. Hand volumes were 494 +/- 6 ml and 312 +/- 7 ml for the immersion method and 476 +/- 14 ml and 302 +/- 8 ml for the overflow method for the two subjects respectively. Using plastic test objects, the mean difference between the actual and measured volume was -0.3% and 2.0% for the immersion and overflow techniques respectively. This study shows that hand volumes can be obtained more quickly than the overflow method. The technique could find an application in clinics where frequent hand volumes are required.

  14. Special Properties of Coherence Scanning Interferometers for large Measurement Volumes

    Science.gov (United States)

    Bauer, W.

    2011-08-01

    In contrast to many other optical methods the uncertainty of Coherence Scanning Interferometer (CSI) in vertical direction is independent from the field of view. Therefore CSIs are ideal instruments for measuring 3D-profiles of larger areas (36×28mm2, e.g.) with high precision. This is of advantage for the determination of form parameters like flatness, parallelism and steps heights within a short time. In addition, using a telecentric beam path allows measurements of deep lying surfaces (automotive suppliers or from the steel industry.

  15. Limb volume measurement: from the past methods to optoelectronic technologies, bioimpedance analysis and laser based devices.

    Science.gov (United States)

    Cavezzi, A; Schingale, F; Elio, C

    2010-10-01

    Accurate measurement of limb volume is considered crucial to lymphedema management. Various non-invasive methods may be used and have been validated in recent years, though suboptimal standardisation has been highlighted in different publications.

  16. Variation in the measurement of cranial volume and surface area using 3D laser scanning technology.

    Science.gov (United States)

    Sholts, Sabrina B; Wärmländer, Sebastian K T S; Flores, Louise M; Miller, Kevin W P; Walker, Phillip L

    2010-07-01

    Three-dimensional (3D) laser scanner models of human crania can be used for forensic facial reconstruction, and for obtaining craniometric data useful for estimating age, sex, and population affinity of unidentified human remains. However, the use of computer-generated measurements in a casework setting requires the measurement precision to be known. Here, we assess the repeatability and precision of cranial volume and surface area measurements using 3D laser scanner models created by different operators using different protocols for collecting and processing data. We report intraobserver measurement errors of 0.2% and interobserver errors of 2% of the total area and volume values, suggesting that observer-related errors do not pose major obstacles for sharing, combining, or comparing such measurements. Nevertheless, as no standardized procedure exists for area or volume measurements from 3D models, it is imperative to report the scanning and postscanning protocols employed when such measurements are conducted in a forensic setting.

  17. Neutron source capability assessment for cumulative fission yields measurements

    Energy Technology Data Exchange (ETDEWEB)

    Descalle, M A; Dekin, W; Kenneally, J

    2011-04-06

    A recent analysis of high-quality cumulative fission yields data for Pu-239 published in the peer-reviewed literature showed that the quoted experimental uncertainties do not allow a clear statement on how the fission yields vary as a function of energy. [Prussin2009] To make such a statement requires a set of experiments with well 'controlled' and understood sources of experimental errors to reduce uncertainties as low as possible, ideally in the 1 to 2% range. The Inter Laboratory Working Group (ILWOG) determined that Directed Stockpile Work (DSW) would benefit from an experimental program with the stated goal to reduce the measurement uncertainties significantly in order to make a definitive statement of the relationship of energy dependence to the cumulative fission yields. Following recent discussions between Lawrence Livermore National Laboratory (LLNL) and Los Alamos National Laboratory (LANL), there is a renewed interest in developing a concerted experimental program to measure fission yields in a neutron energy range from thermal energy (0.025 eV) to 14 MeV with an emphasis on discrete energies from 0.5 to 4 MeV. Ideally, fission yields would be measured at single energies, however, in practice there are only 'quasi-monoenergetic' neutrons sources of finite width. This report outlines a capability assessment as of June 2011 of available neutron sources that could be used as part of a concerted experimental program to measure cumulative fission yields. In a framework of international collaborations, capabilities available in the United States, at the Atomic Weapons Establishment (AWE) in the United Kingdom and at the Commissariat Energie Atomique (CEA) in France are listed. There is a need to develop an experimental program that will reduce the measurement uncertainties significantly in order to make a definitive statement of the relationship of energy dependence to the cumulative fission yields. Fission and monoenergetic neutron sources

  18. Evaluation of Anterior Chamber Volume in Cataract Patients with Swept-Source Optical Coherence Tomography

    Directory of Open Access Journals (Sweden)

    Wenwen He

    2016-01-01

    Full Text Available Purpose. To evaluate the anterior chamber volume in cataract patients with Swept-Source Optical Coherence Tomography (SS-OCT and its influencing factors. Methods. Anterior chamber volume of 92 cataract patients was evaluated with SS-OCT in this cross-sectional study. Univariate analyses and multiple linear regression were used to investigate gender, age, operated eye, posterior vitreous detachment, lens opacity grading, and axial length (AXL related variables capable of influencing the ACV. Results. The average ACV was 139.80 ± 38.21 mm3 (range 59.41 to 254.09 mm3. The average ACV was significantly larger in male patients than in female patients (P=0.001. ACV was negatively correlated with age and LOCS III cortical (C grading of the lens (Pearson’s correlation analysis, r=-0.443, P<0.001, and Spearman’s correlation analysis, ρ=-0.450, P<0.001. ACV was also increased with AXL (Pearson’s correlation analysis, r=0.552, P<0.001. Multiple linear regression showed that, with all of the covariates entered into the model, gender (P=0.002, age (P=0.015, LOCS III C grade (P=0.043, and AXL (P=0.001 were still associated with ACV (F=10.252  P<0.001  R2=0.498. Conclusion. With SS-OCT, we found that, in healthy cataract patients, ACV varied significantly among different subjects. Influencing factors that contribute to reduced ACV were female gender, increased age, LOCS III C grade, and shorter AXL.

  19. Measuring the volume of uterine fibroids using 2- and 3-dimensional ultrasound and comparison with histopathology.

    Science.gov (United States)

    Zivković, Nikica; Zivković, Kreiimir; Despot, Albert; Paić, Josip; Zelić, Ana

    2012-12-01

    The aim of this study was clinical testing of the reliability and usability of three-dimensional (3D) and two-dimensional (2D) ultrasound (US) technology. The ultimate aim and purpose of this study was to establish ultrasound methods, standards and protocols for determining the volume of any gynecologic organ or tumor. The study included 31 women in reproductive age and postmenopause. All patients were examined with a RIC 5-9 3D-endovaginal probe (4.3-7.5 MHz) on a Voluson 730 Pro ultrasound device. The volume of myomas was measured by using the existing 2D and 3D ultrasound methods on the above mentioned device. All patients underwent myomectomy or hysterectomy due to clinically and ultrasonographically diagnosed uterine myomas indicating operative intervention. After the operation, the pathologist determined the volume of removed myomas by measuring them in a gauge bowl containing water, i.e. using Archimedes' principle (lift), serving as the control group with histopathologic diagnosis. A total of 155 myoma volumes were processed on 2D display, 31 myoma volumes were preoperatively measured on 3D display and 31 myoma volumes were measured by the pathologist. The values of US measurements for each US method were expressed as mean value of all measurements of myoma volumes. Statistical processing of the results and Student's t-test for independent samples revealed that the 2nd examined US method (measuring of myoma by using an ellipse and the longer tumor diameter) and 4th examined US method (measuring of myoma by using the longer and shorter tumor diameters together with establishing their mean values) in 2D US technique, as well as the 6th examined US method in 3D US technique showed no significant measurement differences in comparison with control measurement in a gauge bowl containing water (p < 0.05), indicating acceptability of the US methods for verifying tumor volumes. The standard error in determining the volume of myomas by the above US methods varied

  20. Special Properties of Coherence Scanning Interferometers for large Measurement Volumes

    Energy Technology Data Exchange (ETDEWEB)

    Bauer, W, E-mail: W.bauer@polytec.de [Polytec GmbH, Polytec Platz 1-7, 76337 Waldbronn (Germany)

    2011-08-19

    In contrast to many other optical methods the uncertainty of Coherence Scanning Interferometer (CSI) in vertical direction is independent from the field of view. Therefore CSIs are ideal instruments for measuring 3D-profiles of larger areas (36x28mm{sup 2}, e.g.) with high precision. This is of advantage for the determination of form parameters like flatness, parallelism and steps heights within a short time. In addition, using a telecentric beam path allows measurements of deep lying surfaces (<70mm) and the determination of form parameters with large step-heights. The lateral and spatial resolution, however, are reduced. In this presentation different metrological characteristics together with their potential errors are analyzed for large-scale measuring CSIs. Therefore these instruments are ideal tools in quality control for good/bad selections, e.g. The consequences for the practical use in industry and for standardization are discussed by examples of workpieces of automotive suppliers or from the steel industry.

  1. Low contrast medium-volume third-generation dual-source computed tomography angiography for transcatheter aortic valve replacement planning

    Energy Technology Data Exchange (ETDEWEB)

    Felmly, Lloyd M. [Medical University of South Carolina, Division of Cardiovascular Imaging, Department of Radiology and Radiological Science, Charleston, SC (United States); Medical University of South Carolina, Division of Cardiothoracic Surgery, Department of Surgery, Charleston, SC (United States); De Cecco, Carlo N.; Varga-Szemes, Akos; McQuiston, Andrew D. [Medical University of South Carolina, Division of Cardiovascular Imaging, Department of Radiology and Radiological Science, Charleston, SC (United States); Schoepf, U.J.; Litwin, Sheldon E.; Bayer, Richard R. [Medical University of South Carolina, Division of Cardiovascular Imaging, Department of Radiology and Radiological Science, Charleston, SC (United States); Medical University of South Carolina, Division of Cardiology, Department of Medicine, Charleston, SC (United States); Mangold, Stefanie [Medical University of South Carolina, Division of Cardiovascular Imaging, Department of Radiology and Radiological Science, Charleston, SC (United States); University Hospital of Tuebingen, Department of Diagnostic and Interventional Radiology, Tuebingen (Germany); Vogl, Thomas J. [University Hospital Frankfurt, Department of Diagnostic and Interventional Radiology, Frankfurt (Germany); Wichmann, Julian L. [Medical University of South Carolina, Division of Cardiovascular Imaging, Department of Radiology and Radiological Science, Charleston, SC (United States); University Hospital Frankfurt, Department of Diagnostic and Interventional Radiology, Frankfurt (Germany)

    2017-05-15

    To investigate feasibility, image quality and safety of low-tube-voltage, low-contrast-volume comprehensive cardiac and aortoiliac CT angiography (CTA) for planning transcatheter aortic valve replacement (TAVR). Forty consecutive TAVR candidates prospectively underwent combined CTA of the aortic root and vascular access route (270 mgI/ml iodixanol). Patients were assigned to group A (second-generation dual-source CT [DSCT], 100 kV, 60 ml contrast, 4.0 ml/s flow rate) or group B (third-generation DSCT, 70 kV, 40 ml contrast, 2.5 ml/s flow rate). Vascular attenuation, noise, signal-to-noise (SNR) and contrast-to-noise ratios (CNR) were compared. Subjective image quality was assessed by two observers. Estimated glomerular filtration (eGFR) at CTA and follow-up were measured. Besides a higher body-mass-index in group B (24.8±3.8 kg/m{sup 2} vs. 28.1±5.4 kg/m{sup 2}, P=0.0339), patient characteristics between groups were similar (P≥0.0922). Aortoiliac SNR (P=0.0003) was higher in group B. Cardiac SNR (P=0.0003) and CNR (P=0.0181) were higher in group A. Subjective image quality was similar (P≥0.213) except for aortoiliac image noise (4.42 vs. 4.12, P=0.0374). TAVR-planning measurements were successfully obtained in all patients. There were no significant changes in eGFR among and between groups during follow-up (P≥0.302). TAVR candidates can be safely and effectively evaluated by a comprehensive CTA protocol with low contrast volume using low-tube-voltage acquisition. (orig.)

  2. Accurate monitoring of intravascular fluid volume: A novel application of intrathoracic impedance measures for the guidance of volume reduction therapy

    Directory of Open Access Journals (Sweden)

    Barbara A. Lara

    2015-09-01

    Conclusion: Impedance vectors derived from a multivector monitoring system reflect changes in intravascular plasma volume. Two of these vectors most closely track changes in plasma volume and may be used to more accurately guide and optimize volume reduction therapy.

  3. Comparison of aerosol volume size distributions between column and surface measurements downwind of Seoul, Korea

    Science.gov (United States)

    Park, J. S.; Choi, Y.; Ghim, Y. S.

    2015-12-01

    The aerosol volume size distribution is one of the most important parameters in retrieving aerosol optical properties and studying radiative forcing. The column-integrated aerosol volume size distribution for AERONET was obtained from inversion product level 1.5 (22 bins between 0.1 and 30 μm in diameter) from the measurements of CIMEL sunphotometer (CE-318); that for SKYNET was obtained using skyrad.pack V5 (20 bins, 0.02-33 μm) from the measurements of PREDE skyradiometer (POM-02). The aerosol volume size distribution at the surface was measured using a wide range aerosol spectrometer system consisting of a scanning mobility particle scanner (Grimm, Model 5.419; 89 bins, 0.005-0.35 μm) and an optical particle counter (Grimm, Model 1.109; 31 bins, 0.27-34 μm). The measurement was conducted in Yongin, downwind of Seoul, Korea, from April 30 to June 27, 2015. The measurement site is located on the rooftop of a five-story building on the hill (37.34°N, 127.27°E, 167 m above sea level) in the global campus of Hankuk University of Foreign Studies. To investigate the discrepancy in effective diameter and fine mode volume fraction, we compared the volume size distributions when the measurement time coincided within 5 minutes because the measurement intervals were different between instruments.

  4. sources

    Directory of Open Access Journals (Sweden)

    Shu-Yin Chiang

    2002-01-01

    Full Text Available In this paper, we study the simplified models of the ATM (Asynchronous Transfer Mode multiplexer network with Bernoulli random traffic sources. Based on the model, the performance measures are analyzed by the different output service schemes.

  5. A new method for the measurement of meteorite bulk volume via ideal gas pycnometry

    Science.gov (United States)

    Li, Shijie; Wang, Shijie; Li, Xiongyao; Li, Yang; Liu, Shen; Coulson, Ian M.

    2012-10-01

    To date, of the many techniques used to measure the bulk volume of meteorites, only three methods (Archimedean bead method, 3-D laser imaging and X-ray microtomography) can be considered as nondestructive or noncontaminating. The bead method can show large, random errors for sample sizes of smaller than 5 cm3. In contrast, 3-D laser imaging is a high-accuracy method even when measuring the bulk volumes of small meteorites. This method is both costly and time consuming, however, and meteorites of a certain shape may lead to some uncertainties in the analysis. The method of X-ray microtomography suffers from the same problems as 3-D laser imaging. This study outlines a new method of high-accuracy, nondestructive and noncontaminating measurement of the bulk volume of meteorite samples. In order to measure the bulk volume of a meteorite, one must measure the total volume of the balloon vacuum packaged meteorite and the volume of balloon that had been used to enclose the meteorite using ideal gas pycnometry. The difference between the two determined volumes is the bulk volume of the meteorite. Through the measurement of zero porosity metal spheres and tempered glass fragments, our results indicate that for a sample which has a volume of between 0.5 and 2 cm3, the relative error of the measurement is less than ±0.6%. Furthermore, this error will be even smaller (less than ±0.1%) if the determined sample size is larger than 2 cm3. The precision of this method shows some volume dependence. For samples smaller than 1 cm3, the standard deviations are less than ±0.328%, and these values will fall to less than ±0.052% for samples larger than 2 cm3. The porosities of nine fragments of Jilin, GaoGuenie, Zaoyang and Zhaodong meteorites have been measured using our vacuum packaging-pycnometry method, with determined average porosities of Jilin, GaoGuenie, Zaoyang and Zhaodong of 9.0307%, 2.9277%, 17.5437% and 5.9748%, respectively. These values agree well with the porosities

  6. Greenhouse Gas Source Attribution: Measurements Modeling and Uncertainty Quantification

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Zhen [Sandia National Lab. (SNL-CA), Livermore, CA (United States); Safta, Cosmin [Sandia National Lab. (SNL-CA), Livermore, CA (United States); Sargsyan, Khachik [Sandia National Lab. (SNL-CA), Livermore, CA (United States); Najm, Habib N. [Sandia National Lab. (SNL-CA), Livermore, CA (United States); van Bloemen Waanders, Bart Gustaaf [Sandia National Lab. (SNL-CA), Livermore, CA (United States); LaFranchi, Brian W. [Sandia National Lab. (SNL-CA), Livermore, CA (United States); Ivey, Mark D. [Sandia National Lab. (SNL-CA), Livermore, CA (United States); Schrader, Paul E. [Sandia National Lab. (SNL-CA), Livermore, CA (United States); Michelsen, Hope A. [Sandia National Lab. (SNL-CA), Livermore, CA (United States); Bambha, Ray P. [Sandia National Lab. (SNL-CA), Livermore, CA (United States)

    2014-09-01

    In this project we have developed atmospheric measurement capabilities and a suite of atmospheric modeling and analysis tools that are well suited for verifying emissions of green- house gases (GHGs) on an urban-through-regional scale. We have for the first time applied the Community Multiscale Air Quality (CMAQ) model to simulate atmospheric CO2 . This will allow for the examination of regional-scale transport and distribution of CO2 along with air pollutants traditionally studied using CMAQ at relatively high spatial and temporal resolution with the goal of leveraging emissions verification efforts for both air quality and climate. We have developed a bias-enhanced Bayesian inference approach that can remedy the well-known problem of transport model errors in atmospheric CO2 inversions. We have tested the approach using data and model outputs from the TransCom3 global CO2 inversion comparison project. We have also performed two prototyping studies on inversion approaches in the generalized convection-diffusion context. One of these studies employed Polynomial Chaos Expansion to accelerate the evaluation of a regional transport model and enable efficient Markov Chain Monte Carlo sampling of the posterior for Bayesian inference. The other approach uses de- terministic inversion of a convection-diffusion-reaction system in the presence of uncertainty. These approaches should, in principle, be applicable to realistic atmospheric problems with moderate adaptation. We outline a regional greenhouse gas source inference system that integrates (1) two ap- proaches of atmospheric dispersion simulation and (2) a class of Bayesian inference and un- certainty quantification algorithms. We use two different and complementary approaches to simulate atmospheric dispersion. Specifically, we use a Eulerian chemical transport model CMAQ and a Lagrangian Particle Dispersion Model - FLEXPART-WRF. These two models share the same WRF

  7. Inter-observer variation in ultrasound measurement of the volume and diameter of thyroid nodules

    Energy Technology Data Exchange (ETDEWEB)

    Choi, Young Jun; Baek, Jung Hwan; Hong, Min Ji; Lee, Jeong Hyun [Dept. of Radiology, and Research Institute of Radiology, Asan Medical Center, University of Ulsan College of Medicine, Seoul (Korea, Republic of)

    2015-06-15

    Thyroid nodule measurement using ultrasonography (US) is widely performed in various clinical scenarios. The purpose of this study was to evaluate inter-observer variation in US measurement of the volume and maximum diameter of thyroid nodules. This retrospective study included 73 consecutive patients with 85 well-defined thyroid nodules greater than 1 cm in their maximum diameter. US examinations were independently performed by using standardized measurement methods, conducted by two clinically experienced thyroid radiologists. The maximum nodule diameter and nodule volume, calculated from nodule diameters using the ellipsoid formula, were obtained by each reader. Inter-observer variations in volume and maximum diameter were determined using 95% Bland-Altman limits of agreement. The degree of inter-observer variations in volumes and the maximum diameters were compared using the Student's t test, between nodules < 2 cm in maximum diameter and those with > or = 2 cm. The mean inter-observer difference in measuring the nodule volume was -1.6%, in terms of percentage of the nodule volume, and the 95% limit of agreement was +/- 13.1%. For maximum nodule diameter, the mean inter-observer difference was -0.6%, in terms of percentage of the nodule diameter, and the 95% limit of agreement was +/- 7.3%. Inter-observer variation in volume was greater in nodules of < 2 cm in maximum diameter, compared to the larger nodules (p = 0.035). However, no statistically significant difference was noted between the two groups regarding maximum nodule diameters (p = 0.511). Any differences smaller than 13.1% and 7.3% in volume and maximum diameter, respectively, measured by using US for well-defined thyroid nodules of > 1 cm should not be considered as a real change in size.

  8. 3D photography is a reliable method of measuring infantile haemangioma volume over time.

    Science.gov (United States)

    Robertson, Sarah A; Kimble, Roy M; Storey, Kristen J; Gee Kee, Emma L; Stockton, Kellie A

    2016-09-01

    Infantile haemangiomas are common lesions of infancy. With the development of novel treatments utilised to accelerate their regression, there is a need for a method of assessing these lesions over time. Volume is an ideal assessment method because of its quantifiable nature. This study investigated whether 3D photography is a valid tool for measuring the volume of infantile haemangiomas over time. Thirteen children with infantile haemangiomas presenting to the Vascular Anomalies Clinic, Royal Children's Hospital/Lady Cilento Children's Hospital treated with propranolol were included in the study. Lesion volume was assessed using 3D photography at presentation, one month and three months follow up. Intrarater reliability was determined by retracing all images several months after the initial mapping. Interrater reliability of the 3D camera software was determined by two investigators, blinded to each other's results, independently assessing infantile haemangioma volume. Lesion volume decreased significantly between presentation and three-month follow-up (p<0.001). Volume intra- and interrater reliability were excellent with ICC 0.991 (95% CI 0.982, 0.995) and 0.978 (95% CI 0.955, 0.989), respectively. This study demonstrates images taken with the 3D LifeViz™ camera and lesion volume calculated with Dermapix® software is a reliable method for assessing infantile haemangioma volume over time. Copyright © 2016 Elsevier Inc. All rights reserved.

  9. Significance of left ventricular volume measurement after heart transplantation using radionuclide techniques

    Energy Technology Data Exchange (ETDEWEB)

    Novitzky, D.; Cooper, D.; Boniaszczuk, J.; Isaacs, S.; Fraser, R.C.; Commerford, P.J.; Uys, C.J.; Rose, A.G.; Smith, J.A.; Barnard, C.N.

    1985-02-01

    Multigated equilibrium blood pool scanning using Technetium 99m labeled red blood cells was used to measure left ventricular volumes in three heterotopic and one orthotopic heart transplant recipient(s). Simultaneously, an endomyocardial biopsy was performed and the degree of acute rejection was assessed by a histological scoring system. The scores were correlated to changes in ejection fraction and heart rate. Technetium 99m scanning data were pooled according to the endomyocardial biopsy score: no rejection; mild rejection; moderate rejection, and severe rejection. In each group, the median of the left ventricular volume parameters was calculated and correlated with the endomyocardial biopsy score, using a non-parametric one-way analysis of variance. A decrease in stroke volume correlated best with the endomyocardial biopsy score during acute rejection. A decrease in end-diastolic left ventricular volumes did not correlate as well. Changes in the end-systolic left ventricular volumes were not statistically significant, but using a simple correlation between end-systolic left ventricular volumes and endomyocardial biopsy the correlation reached significance. Changes in left ventricular volumes measured by Technetium 99m scanning may be useful to confirm the presence or absence of acute rejection in patients with heart grafts.

  10. Hospital procedure volume should not be used as a measure of surgical quality.

    Science.gov (United States)

    LaPar, Damien J; Kron, Irving L; Jones, David R; Stukenborg, George J; Kozower, Benjamin D

    2012-10-01

    The Agency for Healthcare Research and Quality and the Leapfrog Group use hospital procedure volume as a quality measure for pancreatic resection (PR), abdominal aortic aneurysm (AAA) repair, esophageal resection (ER), and coronary artery bypass grafting (CABG). However, controversy exists regarding the strength and validity of the evidence for the volume-outcome association. The purpose of this study was to reevaluate the volume-outcome relationship for these procedures. Discharge data for 261,412 patients were extracted from the 2008 Nationwide Inpatient Sample. The relationship between hospital procedure volume and mortality was rigorously assessed using hierarchical general linear modeling with restricted cubic splines, adjusted for patient demographics, comorbid disease, and elective procedure status. Unadjusted mortality rates were PR (4.7%), AAA (12.7%), ER (5.8%), and CABG (2.2%), and the majority of operations were elective. Hospital procedure volume was not a statistically significant predictor of in-hospital mortality for any of the 4 procedures. Strong predictors of mortality included age, elective procedure status, renal failure, and malnutrition (P procedure volume is not a significant predictor of mortality for the performance of pancreatectomy, AAA repair, esophagectomy, or CABG. Procedure volume by itself should not be used as a proxy measure for surgical quality. Patient mortality risk is primarily attributable to patient-level characteristics such as age and comorbidity.

  11. Measurement of breast volume is a useful supplement to select candidates for surgical breast reduction

    DEFF Research Database (Denmark)

    Ikander, Peder; Drejøe, Jennifer Berg; Lumholt, Pavia

    2014-01-01

    for breast reduction surgery, thus establishing a standard decision basis that can be shared by surgeons and departments to secure patients fair and equal treatment opportunities. MATERIAL AND METHODS: A total of 427 patients who were referred to three Danish public hospitals with breast hypertrophy...... in the period from January 2007 to March 2011 were included prospectively in the study. The patients' subjective complaints, height, weight and standard breast measurements were registered as well as the decision for or against surgery. Breast volume was measured using transparent plastic cups. RESULTS: Cut......-off values for breast volume were calculated based on whether or not the patients were offered reduction surgery. Most patients (93%) with a breast volume below 800 cc were not offered surgery, while most with a volume exceeding 900 cc were offered surgery (94%). In the grey zone between 800 and 900 cc...

  12. Accuracy of cancellous bone volume fraction measured by micro-CT scanning

    DEFF Research Database (Denmark)

    Ding, Ming; Odgaard, A; Hvid, I

    1999-01-01

    Volume fraction, the single most important parameter in describing trabecular microstructure, can easily be calculated from three-dimensional reconstructions of micro-CT images. This study sought to quantify the accuracy of this measurement. One hundred and sixty human cancellous bone specimens...... which covered a large range of volume fraction (9.8-39.8%) were produced. The specimens were micro-CT scanned, and the volume fraction based on Archimedes' principle was determined as a reference. After scanning, all micro-CT data were segmented using individual thresholds determined by the scanner...

  13. LARGE VOLUME IONIZATION CHAMBER USED AS LABORATORY REFERENCE FOR LOW ENERGY X—RAY MEASUREMENT

    Institute of Scientific and Technical Information of China (English)

    杨国山; 薛永库; 等

    1994-01-01

    A large volume spherical ionization chamber of 195mm diameter and 0.36mg/cm2 wall thickness made from conducting carbon-fibre epoxy composite material has been developed.The mechanical intensity of the chamber is satisfactory for a good longterm volume stability.Owing to its large volume and thin wall,the chamber is sensitive to low energy photon beams and has excellent energy-response characteristics.This ionization chamber is suitable not only for a laboratory reference but also for measurement of low energy photon beam exposure rates at protection-level.

  14. Open-source software for demand forecasting of clinical laboratory test volumes using time-series analysis

    Directory of Open Access Journals (Sweden)

    Emad A Mohammed

    2017-01-01

    Full Text Available Background: Demand forecasting is the area of predictive analytics devoted to predicting future volumes of services or consumables. Fair understanding and estimation of how demand will vary facilitates the optimal utilization of resources. In a medical laboratory, accurate forecasting of future demand, that is, test volumes, can increase efficiency and facilitate long-term laboratory planning. Importantly, in an era of utilization management initiatives, accurately predicted volumes compared to the realized test volumes can form a precise way to evaluate utilization management initiatives. Laboratory test volumes are often highly amenable to forecasting by time-series models; however, the statistical software needed to do this is generally either expensive or highly technical. Method: In this paper, we describe an open-source web-based software tool for time-series forecasting and explain how to use it as a demand forecasting tool in clinical laboratories to estimate test volumes. Results: This tool has three different models, that is, Holt-Winters multiplicative, Holt-Winters additive, and simple linear regression. Moreover, these models are ranked and the best one is highlighted. Conclusion: This tool will allow anyone with historic test volume data to model future demand.

  15. Open-source Software for Demand Forecasting of Clinical Laboratory Test Volumes Using Time-series Analysis.

    Science.gov (United States)

    Mohammed, Emad A; Naugler, Christopher

    2017-01-01

    Demand forecasting is the area of predictive analytics devoted to predicting future volumes of services or consumables. Fair understanding and estimation of how demand will vary facilitates the optimal utilization of resources. In a medical laboratory, accurate forecasting of future demand, that is, test volumes, can increase efficiency and facilitate long-term laboratory planning. Importantly, in an era of utilization management initiatives, accurately predicted volumes compared to the realized test volumes can form a precise way to evaluate utilization management initiatives. Laboratory test volumes are often highly amenable to forecasting by time-series models; however, the statistical software needed to do this is generally either expensive or highly technical. In this paper, we describe an open-source web-based software tool for time-series forecasting and explain how to use it as a demand forecasting tool in clinical laboratories to estimate test volumes. This tool has three different models, that is, Holt-Winters multiplicative, Holt-Winters additive, and simple linear regression. Moreover, these models are ranked and the best one is highlighted. This tool will allow anyone with historic test volume data to model future demand.

  16. On-line dynamic measurement of blood viscosity, hematocrit and change of blood volume

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    Objective: To develop an on-line system for the measurement of blood viscosity and hematocrit. The dynamic changes of the macrovascular blood volumes,microvascular blood volumes and the total blood volume were observed by means of calculating from the testing result. Methods: Applying traditional viscosity measurement principle and specific wavelength optic density measurement method, an on-line system for the measurement of blood viscosity and hematocrit was developed, and the A/D multifunctionai board and the testing circuit were designed by ourselves. The system was validated by experiments both in vitro and in vivo. Therapeutic effects of hypertonic saline dextran solution (HSD) and Lactatic Ringer's solution at the early stage after burn-blast combined injury were compared by this method. Results: The results showed that the system has attained the goal of the design. The changes of the blood viscosity and hematocrit could be detected effectively and continuously. The changes of macrovascular, microvascular and total blood volume could be calculated approximately. Conclusions: The system and the method can continuously on-line test the blood viscosity and hematocrit, and reveal the change and distribution of blood volumes more accurately and dearly in the therapy process by estimating changes of the macrovascular, microvascular and total blood volumes, respectively. It has confirmed that HSD treatment could increase blood pressure and attenuate tissue edema by significantly increasing total blood volume,improving macrocirculatory and microcirculatory blood volumes. This study suggested that it could be desirable to develop an experiment technique based on the method mentioned above.

  17. Measurement of Density Inhomogeneity for Source Masses in Time-of-Swing Method of Measuring G

    Institute of Scientific and Technical Information of China (English)

    LIU Lin-Xia; SHAO Cheng-Gang; TU Liang-Cheng; LUO Jun

    2009-01-01

    A method with scanning electron microscopy (SEM) is presented to measure the density inhomogeneity of the stainless steel (SS316) sphere prepared for measuring G using time-of-swing method. The experimental result shows that the relative density inhomogeneity of the sphere is better than 5.9 × 10-4 over the volume of 0.272 × 0.234 × 0.005 mm3. If we assume that the density inhomogeneity of the spheres used in our G measurement is the same as that of the sphere destroyed in testing, it will contribute to G value with an uncertainty of less than O.034 ppm in our G measurement. Furthermore, the mass centre offset from the geometric centre of the sphere will be less than 4.3 × 10-4 μm due to this inhomogeneity.

  18. Volume measurement by using super-resolution MRI: application to prostate volumetry

    CERN Document Server

    Oubel, Estanislao; Iannessi, Antoine

    2015-01-01

    Accuracy and precision of measurements are important for patient follow up in oncology but, unfortunately, partial volume effects introduce an undesired variability between observers. Super resolution techniques (SR) combine multiple acquisitions of an object into a single image richer in details. Herein, the use of SR for reducing variability is investigated in the specific context of prostate measurements. Prostate is typically imaged by T2-weighted MRI in three perpendicular low resolution images, each of them presenting partial volume effects in the direction of the slice selection gradient. SR techniques allow to combine these images into an image presenting the same level of details in all directions. This is expected to increase the accuracy and reproducibility of volume measurements, which in turn improves other derived measurements like PSA density.

  19. Color structured light system of chest wall motion measurement for respiratory volume evaluation.

    Science.gov (United States)

    Chen, Huijun; Cheng, Yuan; Liu, Dongdong; Zhang, Xiaodong; Zhang, Jue; Que, Chengli; Wang, Guangfa; Fang, Jing

    2010-01-01

    We present a structured light system to dynamically measure human chest wall motion for respiratory volume estimation. Based on a projection of an encoded color pattern and a few active markers attached to the trunk, respiratory volumes are obtained by evaluating the 3-D topographic changes of the chest wall in an anatomically consistent measuring region during respiration. Three measuring setups are established: a single-sided illuminating-recording setup for standing posture, an inclined single-sided setup for supine posture, and a double-sided setup for standing posture. Results are compared with the pneumotachography and show good agreement in volume estimations [correlation coefficient: R>0.99 (Pevaluation with high accuracy, but also regional pulmonary function assessment in different chest wall behaviors, with the advantage of whole-field measurement.

  20. A universal and flexible theodolite-camera system for making accurate measurements over large volumes

    Science.gov (United States)

    Zhang, Xiaohu; Zhu, Zhaokun; Yuan, Yun; Li, Lichun; Sun, Xiangyi; Yu, Qifeng; Ou, Jianliang

    2012-11-01

    Typically, optical measurement systems can achieve high accuracy over a limited volume, or cover a large volume with low accuracy. In this paper, we propose a universal way of integrating a camera with a theodolite to construct a theodolite-camera (TC) measurement system that can make measurements over a large volume with high accuracy. The TC inherits the advantages of high flexibility and precision from theodolite and camera, but it avoids the need to perform elaborate adjustments on the camera and theodolite. The TC provides a universal and flexible approach to the camera-on-theodolite system. We describe three types of TC based separately on: (i) a total station; (ii) a theodolite; and (iii) a general rotation frame. We also propose three corresponding calibration methods for the different TCs. Experiments have been conducted to verify the measuring accuracy of each of the three types of TC.

  1. Can cerebral blood volume be measured reproducibly with an improved near infrared spectroscopy system?

    NARCIS (Netherlands)

    Ven, M.T.P. van de; Colier, W.N.J.M.; Sluijs, M.C. van der; Walraven, D.; Oeseburg, B.; Folgering, H.T.M.

    2001-01-01

    In some circumstances, cerebral blood volume (CBV) can be used as a measure for cerebral blood flow. A new near infrared spectroscope was used for determining the reproducibility of CBV measurements assessed by the O2-method. Twenty-seven healthy subjects were investigated. An intrasubject coefficie

  2. A practical method for randoms subtraction in volume imaging PET from detector singles countrate measurements

    Energy Technology Data Exchange (ETDEWEB)

    Smith, R.J.; Karp, J.S. [Univ. of Pennsylvania, Philadelphia, PA (United States). Dept. of Radiology

    1996-06-01

    Randoms subtraction in a volume imaging PET scanner is a significant problem due to the high singles countrates experienced. The delayed coincidence method requires double counting of randoms events and results in a lowered countrate capability. Calculations based on detector singles countrates require complex corrections for countrate dependent livetime and event acceptance due to the camera coincidence processing between the detector and rebinned randoms countrates. The profile distribution method has been used to estimate and subtract both scatter and randoms background but this method is a compromise and couples these 2 sources of background together. In order to avoid these problems and provide accurate subtraction of both the distribution and magnitude of randoms contamination in the scan data the authors have developed an alternative singles based method. The singles distributions are measured across the detectors and are used to construct a randoms distribution sinogram. This distribution is scaled to the appropriate rebinned randoms countrate by means of a lookup table of randoms countrate vs detector singles countrate, generated from phantom calibrations. The advantages of performing randoms subtraction by this method are: (1) there is no increase in camera deadtime, (2) the method compensates for nonuniformities in randoms distributions due to both the activity distribution and nonuniform geometric response of the camera for on and off bankpairs, and (3) it deals with randoms subtraction independently of scatter so that different scatter correction routines may then be applied to the data.

  3. Measuring air layer volumes retained by submerged floating-ferns Salvinia and biomimetic superhydrophobic surfaces

    Directory of Open Access Journals (Sweden)

    Matthias J. Mayser

    2014-06-01

    Full Text Available Some plants and animals feature superhydrophobic surfaces capable of retaining a layer of air when submerged under water. Long-term air retaining surfaces (Salvinia-effect are of high interest for biomimetic applications like drag reduction in ship coatings of up to 30%. Here we present a novel method for measuring air volumes and air loss under water. We recorded the buoyancy force of the air layer on leaf surfaces of four different Salvinia species and on one biomimetic surface using a highly sensitive custom made strain gauge force transducer setup. The volume of air held by a surface was quantified by comparing the buoyancy force of the specimen with and then without an air layer. Air volumes retained by the Salvinia-surfaces ranged between 0.15 and 1 L/m2 depending on differences in surface architecture. We verified the precision of the method by comparing the measured air volumes with theoretical volume calculations and could find a good agreement between both values. In this context we present techniques to calculate air volumes on surfaces with complex microstructures. The introduced method also allows to measure decrease or increase of air layers with high accuracy in real-time to understand dynamic processes.

  4. Three-dimensional measurement of bubble volume based on dual perspective imaging

    Science.gov (United States)

    Xue, Ting; Zhang, Shao-jie; Wu, Bin

    2017-01-01

    This paper presents a new three-dimensional (3D) volume measurement approach of bubble in gas-liquid two-phase flow. According to the dual perspective imaging principle, bubble feature images can be captured from two different view angles. The least square ellipse fitting algorithm is used to figure out the feature parameters from the captured images. Then the 3D volume of bubble can be quantitatively measured. Compaerd with the traditional volume estimation methods based on single perspective imaging, it can effectively reduce the loss of bubble feature information. In the experiment, the 3D volume reconstruction of bubbles from dual perspective images is conducted, and the variation of bubble volume in the bubble rising process is studied. The results show that the measurement accuracy based on the proposed 3D method is higher than those based on traditional methods. The volume of rising bubble is periodically changed, which indicates that bubble achieves periodic rotation and deformation in the rising process.

  5. Spatial Visualization Tasks To Support Students’ Spatial Structuring In Learning Volume Measurement

    Directory of Open Access Journals (Sweden)

    Shintia Revina

    2011-07-01

    Full Text Available Many prior researches found that most of students in grade five tended to have difficulty in fully grasping the concept of volume measurement because they have to build their competence in spatial structuring. The unit of volume “packing” measurement must be integrated and coordinated in three-dimension. On the other hand, it is revealed the errors that students made on the volume measurement tasks with threedimensional cube arrays are related to some aspects of spatial visualization, such as the skill to "read off" two-dimensional representation of solid objects. For those reasons, this research is aimed to develop classroom activities with the use of spatial visualization tasks to support students’ spatial structuring in learning volume measurement. Consequently, design research was chosen as an appropriate means to achieve this research goal. In this research, a sequence of instructional activities is designed and developed based on the hypothesis of students’ learning processes. This research was conducted in grade 5 of SD Pupuk Sriwijaya Palembang, Indonesia.Keywords: volume measurement, spatial structuring, spatial visualization, design research. DOI: http://dx.doi.org/10.22342/jme.2.2.745.127-146

  6. Validity and repeatability of a depth camera-based surface imaging system for thigh volume measurement.

    Science.gov (United States)

    Bullas, Alice M; Choppin, Simon; Heller, Ben; Wheat, Jon

    2016-10-01

    Complex anthropometrics such as area and volume, can identify changes in body size and shape that are not detectable with traditional anthropometrics of lengths, breadths, skinfolds and girths. However, taking these complex with manual techniques (tape measurement and water displacement) is often unsuitable. Three-dimensional (3D) surface imaging systems are quick and accurate alternatives to manual techniques but their use is restricted by cost, complexity and limited access. We have developed a novel low-cost, accessible and portable 3D surface imaging system based on consumer depth cameras. The aim of this study was to determine the validity and repeatability of the system in the measurement of thigh volume. The thigh volumes of 36 participants were measured with the depth camera system and a high precision commercially available 3D surface imaging system (3dMD). The depth camera system used within this study is highly repeatable (technical error of measurement (TEM) of <1.0% intra-calibration and ~2.0% inter-calibration) but systematically overestimates (~6%) thigh volume when compared to the 3dMD system. This suggests poor agreement yet a close relationship, which once corrected can yield a usable thigh volume measurement.

  7. Magnetic Resonance Venous Volume Measurements in Peripheral Artery Disease (from ELIMIT).

    Science.gov (United States)

    Kamran, Hassan; Nambi, Vijay; Negi, Smita; Yang, Eric Y; Chen, Changyi; Virani, Salim S; Kougias, Panos; Lumsden, Alan B; Morrisett, Joel D; Ballantyne, Christie M; Brunner, Gerd

    2016-11-01

    The relation between the arterial and venous systems in patients with impaired lower extremity blood flow remains poorly described. The objective of this secondary analysis of the Effectiveness of Intensive Lipid Modification Medication in Preventing the Progression on Peripheral Artery Disease Trial was to determine the association between femoral vein (FV) volumes and measurements of peripheral artery disease. FV wall, lumen, and total volumes were quantified with fast spin-echo proton density-weighted magnetic resonance imaging scans in 79 patients with peripheral artery disease over 2 years. Reproducibility was excellent for FV total vessel (intraclass correlation coefficient 0.924, confidence interval 0.910 to 0.935) and lumen volumes (intraclass correlation coefficient 0.893, confidence interval 0.873 to 0.910). Baseline superficial femoral artery volumes were directly associated with FV wall (r = 0.46, p <0.0001), lumen (r = 0.42, p = 0.0001), and total volumes (r = 0.46, p <0.0001). The 2-year change in maximum walking time was inversely associated with the 24-month change in FV total volume (r = -0.45, p = 0.03). In conclusion, FV volumes can be measured reliably with fast spin-echo proton density-weighted magnetic resonance imaging, and baseline superficial femoral artery plaque burden is positively associated with FV volumes, whereas the 2-year change in FV volumes and leg function show an inverse relation.

  8. Location studies of prostate volume measurement by using transrectal ultrasonography: Experimental study by self-produced prostate phantom

    Energy Technology Data Exchange (ETDEWEB)

    Yoon, Joon; Byeon, Il Kyun; Lee, Hoo Min [Dept. of Radiological Science, (Korea, Republic of); Kim, Yun Min; Kim, Hyeong Gyun [Dept. of Radiological Technology, Dongnam Health University, Suwon (Korea, Republic of)

    2015-12-15

    Accurate volume measurement of the prostate is a significant role in determining the result of diagnosis and treatment of benign prostate hyperplasia. The purpose of this study was to determine, when measuring prostate volume by TRUS, whether location is more accurately determined by transaxial or longitudinal scanning. With reference to the patient’s image, it was produced six prostate model. It compares the actual volume and the measurement volume, and find the optimal measurement position of each specific model. Prostate volume measured by TRUS closely correlates with prostate phantom volume. There was no significant difference(p = .156). To measure the accurate volume of prostate with focal protrusion, its length should be measured exclude the protrusions.

  9. TOF Spectroscopy measurement with waveform Digitizer at TMSR Photoneutron Source

    CERN Document Server

    Liu, Longxiang; Ma, Yugang; Cao, Xiguang; Cai, Xiangzhou; Chen, Jingen; Zhang, Guilin; Han, Jianlong; Zhang, Guogiang; Hu, Jifeng; Wang, Xiaohe

    2015-01-01

    The Photo-Neutron Source(PNS,phase 1), is an electron linear accelerator (linac) based pulsed neutron facility, combined with TOF technique, was constructed for nuclear data measurement of Thorium Molten Salt Reactor(TMSR) in Shanghai Institute of Applied Physics(SINAP) at JiaDing campus. The TOF detector signal, with the arrive time, pulse shape and pulse hight information, was recorded by a waveform digitizer. Through the pulse-shape discrimination(PSD) between neutrons and gamma-rays and time of Gamma Flash and Neutron signal analyse, the neutron TOF spectrum was deduced with this simple electronics design, and a new DAQ system based on waveform digitizer was used in this test experiment.

  10. Finite Volume Based Computer Program for Ground Source Heat Pump System

    Energy Technology Data Exchange (ETDEWEB)

    Menart, James A. [Wright State University

    2013-02-22

    This report is a compilation of the work that has been done on the grant DE-EE0002805 entitled ?Finite Volume Based Computer Program for Ground Source Heat Pump Systems.? The goal of this project was to develop a detailed computer simulation tool for GSHP (ground source heat pump) heating and cooling systems. Two such tools were developed as part of this DOE (Department of Energy) grant; the first is a two-dimensional computer program called GEO2D and the second is a three-dimensional computer program called GEO3D. Both of these simulation tools provide an extensive array of results to the user. A unique aspect of both these simulation tools is the complete temperature profile information calculated and presented. Complete temperature profiles throughout the ground, casing, tube wall, and fluid are provided as a function of time. The fluid temperatures from and to the heat pump, as a function of time, are also provided. In addition to temperature information, detailed heat rate information at several locations as a function of time is determined. Heat rates between the heat pump and the building indoor environment, between the working fluid and the heat pump, and between the working fluid and the ground are computed. The heat rates between the ground and the working fluid are calculated as a function time and position along the ground loop. The heating and cooling loads of the building being fitted with a GSHP are determined with the computer program developed by DOE called ENERGYPLUS. Lastly COP (coefficient of performance) results as a function of time are provided. Both the two-dimensional and three-dimensional computer programs developed as part of this work are based upon a detailed finite volume solution of the energy equation for the ground and ground loop. Real heat pump characteristics are entered into the program and used to model the heat pump performance. Thus these computer tools simulate the coupled performance of the ground loop and the heat pump

  11. Recovery Act: Finite Volume Based Computer Program for Ground Source Heat Pump Systems

    Energy Technology Data Exchange (ETDEWEB)

    James A Menart, Professor

    2013-02-22

    This report is a compilation of the work that has been done on the grant DE-EE0002805 entitled Finite Volume Based Computer Program for Ground Source Heat Pump Systems. The goal of this project was to develop a detailed computer simulation tool for GSHP (ground source heat pump) heating and cooling systems. Two such tools were developed as part of this DOE (Department of Energy) grant; the first is a two-dimensional computer program called GEO2D and the second is a three-dimensional computer program called GEO3D. Both of these simulation tools provide an extensive array of results to the user. A unique aspect of both these simulation tools is the complete temperature profile information calculated and presented. Complete temperature profiles throughout the ground, casing, tube wall, and fluid are provided as a function of time. The fluid temperatures from and to the heat pump, as a function of time, are also provided. In addition to temperature information, detailed heat rate information at several locations as a function of time is determined. Heat rates between the heat pump and the building indoor environment, between the working fluid and the heat pump, and between the working fluid and the ground are computed. The heat rates between the ground and the working fluid are calculated as a function time and position along the ground loop. The heating and cooling loads of the building being fitted with a GSHP are determined with the computer program developed by DOE called ENERGYPLUS. Lastly COP (coefficient of performance) results as a function of time are provided. Both the two-dimensional and three-dimensional computer programs developed as part of this work are based upon a detailed finite volume solution of the energy equation for the ground and ground loop. Real heat pump characteristics are entered into the program and used to model the heat pump performance. Thus these computer tools simulate the coupled performance of the ground loop and the heat pump. The

  12. In Situ Void Fraction and Gas Volume in Hanford Tank 241-SY-101 as Measured with the Void Fraction Instrument

    Energy Technology Data Exchange (ETDEWEB)

    CW Stewart; G Chen; JM Alzheimer; PA Meyer

    1998-11-10

    The void fraction instrument (WI) was deployed in Tank 241-SY-101 three times in 1998 to confm and locate the retained gas (void) postulated to be causing the accelerating waste level rise observed since 1995. The design, operation, and data reduction model of the WI are described along with validation testing and potential sources of uncertainty. The test plans, field observations and void measurements are described in detail, including the total gas volume calculations and the gas volume model. Based on 1998 data, the void fraction averaged 0.013 i 0.001 in the mixed slurry and 0.30 ~ 0.04 in the crust. This gives gas volumes (at standard pressure and temperature) of 87 t 9 scm in the slurry and 138 ~ 22 scm in the crust for a total retained gas volume of221 *25 scm. This represents an increase of about 74 scm in the crust and a decrease of about 34 scm in the slurry from 1994/95 results. The overall conclusion is that the gas retention is occurring mainly in the crust layer and there is very little gas in the mixed slurry and loosely settled layers below. New insights on crust behavior are also revealed.

  13. Comparison between CT volume measurement and histopathological assessment of response to neoadjuvant therapy in rectal cancer

    Energy Technology Data Exchange (ETDEWEB)

    Pomerri, Fabio, E-mail: fabio.pomerri@unipd.it [Veneto Institute of Oncology IOV-IRCCS, via Gattamelata 64, 35128 Padua (Italy); Department of Medicine, University of Padua, via Giustiniani 2, 35128 Padua (Italy); Pucciarelli, Salvatore, E-mail: puc@unipd.it [Department of Oncological and Surgical Sciences, University of Padua, via Giustiniani 2, 35128 Padua (Italy); Gennaro, Gisella, E-mail: gisella.gennaro@pd.infn.it [Veneto Institute of Oncology IOV-IRCCS, via Gattamelata 64, 35128 Padua (Italy); Maretto, Isacco, E-mail: isac77@gmail.com [Veneto Institute of Oncology IOV-IRCCS, via Gattamelata 64, 35128 Padua (Italy); Nitti, Donato, E-mail: donato.nitti@unipd.it [Department of Oncological and Surgical Sciences, University of Padua, via Giustiniani 2, 35128 Padua (Italy); Muzzio, Pier Carlo, E-mail: pcmuzzio@unipd.it [Veneto Institute of Oncology IOV-IRCCS, via Gattamelata 64, 35128 Padua (Italy)

    2012-12-15

    Objectives: The aim of this study was to compare volume measurements on computed tomography (CT) images with histopathological assessments of chemoradiotherapy (CRT)-induced tumor regression in locally advanced rectal cancer (RC). Methods: In 25 patients (13 males, 12 females; median age, 63 years; age range, 44–79 years) with locally advanced RC treated with preoperative CRT and surgery, two radiologists measured tumor volume on CT images before and after CRT. CT-based tumor volumetry and the modified response evaluation criteria in solid tumors (mRECISTs) were compared with T and N downstaging after CRT, and with the tumor regression grade (TRG). Results: Tumor volumes were significantly smaller on CT images after CRT. The tumors regressed in 52% (13/25), 36% (9/25) and 40% (10/25) of patients, based on T downstaging, TRG and mRECIST findings, respectively. In terms of T downstaging, the pre- and post-CRT tumor volumes of responders and non-responders to the treatment differed statistically, while their tumor volume reduction rates and volume reductions according to the 65% mRECIST threshold did not. In terms of N downstaging and TRG, the differences between the responders’ and the non-responders’ pre- and post-CRT tumor volumes, tumor volume reduction rates, and mRECIST thresholds were never statistically significant. Conclusion: Measuring tumor size on CT images is of limited value in predicting the histopathological response to preoperative CRT in RC patients, so it may be unwise to select surgical treatment strategies based on CT volumetry.

  14. Effect of malaria on placental volume measured using three-dimensional ultrasound: a pilot study

    Directory of Open Access Journals (Sweden)

    Rijken Marcus J

    2012-01-01

    Full Text Available Abstract Background The presence of malaria parasites and histopathological changes in the placenta are associated with a reduction in birth weight, principally due to intrauterine growth restriction. The aim of this study was to examine the feasibility of studying early pregnancy placental volumes using three-dimensional (3D ultrasound in a malaria endemic area, as a small volume in the second trimester may be an indicator of intra-uterine growth restriction and placental insufficiency. Methods Placenta volumes were acquired using a portable ultrasound machine and a 3D ultrasound transducer and estimated using the Virtual Organ Computer-aided AnaLysis (VOCAL image analysis software package. Intra-observer reliability and limits of agreement of the placenta volume measurements were calculated. Polynomial regression models for the mean and standard deviation as a function of gestational age for the placental volumes of uninfected women were created and tested. Based on these equations each measurement was converted into a z -score. The z-scores of the placental volumes of malaria infected and uninfected women were then compared. Results Eighty-four women (uninfected = 65; infected = 19 with a posterior placenta delivered congenitally normal, live born, single babies. The mean placental volumes in the uninfected women were modeled to fit 5th, 10th, 50th, 90th and 95th centiles for 14-24 weeks' gestation. Most placenta volumes in the infected women were below the 50th centile for gestational age; most of those with Plasmodium falciparum were below the 10th centile. The 95% intra-observer limits of agreement for first and second measurements were ± 37.0 mL and ± 25.4 mL at 30 degrees and 15 degrees rotation respectively. Conclusion The new technique of 3D ultrasound volumetry of the placenta may be useful to improve our understanding of the pathophysiological constraints on foetal growth caused by malaria infection in early pregnancy.

  15. MRI markers for mild cognitive impairment: comparisons between white matter integrity and gray matter volume measurements.

    Directory of Open Access Journals (Sweden)

    Yu Zhang

    Full Text Available The aim of the study was to evaluate the value of assessing white matter integrity using diffusion tensor imaging (DTI for classification of mild cognitive impairment (MCI and prediction of cognitive impairments in comparison to brain atrophy measurements using structural MRI. Fifty-one patients with MCI and 66 cognitive normal controls (CN underwent DTI and T1-weighted structural MRI. DTI measures included fractional anisotropy (FA and radial diffusivity (DR from 20 predetermined regions-of-interest (ROIs in the commissural, limbic and association tracts, which are thought to be involved in Alzheimer's disease; measures of regional gray matter (GM volume included 21 ROIs in medial temporal lobe, parietal cortex, and subcortical regions. Significant group differences between MCI and CN were detected by each MRI modality: In particular, reduced FA was found in splenium, left isthmus cingulum and fornix; increased DR was found in splenium, left isthmus cingulum and bilateral uncinate fasciculi; reduced GM volume was found in bilateral hippocampi, left entorhinal cortex, right amygdala and bilateral thalamus; and thinner cortex was found in the left entorhinal cortex. Group classifications based on FA or DR was significant and better than classifications based on GM volume. Using either DR or FA together with GM volume improved classification accuracy. Furthermore, all three measures, FA, DR and GM volume were similarly accurate in predicting cognitive performance in MCI patients. Taken together, the results imply that DTI measures are as accurate as measures of GM volume in detecting brain alterations that are associated with cognitive impairment. Furthermore, a combination of DTI and structural MRI measurements improves classification accuracy.

  16. Quantitative absorption cytometry for measuring red blood cell hemoglobin mass and volume.

    Science.gov (United States)

    Schonbrun, Ethan; Malka, Roy; Di Caprio, Giuseppe; Schaak, Diane; Higgins, John M

    2014-04-01

    We present an optical system, called the quantitative absorption cytometer (QAC), to measure the volume and hemoglobin mass of red blood cells flowing through a microfluidic channel. In contrast to clinical hematology analyzers, where cells are sphered in order for both volume and hemoglobin to be measured accurately, the QAC measures cells in their normal physiological shape. Human red blood cells are suspended in a refractive index-matching absorbing buffer, driven through a microfluidic channel, and imaged using a transmission light microscope onto a color camera. A red and a blue LED illuminate cells and images at each color are used to independently retrieve cell volume and hemoglobin mass. This system shows good agreement with red blood cell indices retrieved by a clinical hematology analyzer and in fact measures a smaller coefficient of variation of hemoglobin concentration. In addition to cell indices, the QAC returns height and mass maps of each measured cell. These quantitative images are valuable for analyzing the detailed morphology of individual cells as well as statistical outliers found in the data. We also measured red blood cells in hypertonic and hypotonic buffers to quantify the correlation between volume and hemoglobin mass under osmotic stress. Because this method is invariant to cell shape, even extremely nonspherical cells in hypertonic buffers can be measured accurately.

  17. Comparative analysis of two methods for measuring sales volumes during malaria medicine outlet surveys.

    Science.gov (United States)

    Patouillard, Edith; Kleinschmidt, Immo; Hanson, Kara; Pok, Sochea; Palafox, Benjamin; Tougher, Sarah; O'Connell, Kate; Goodman, Catherine

    2013-09-05

    There is increased interest in using commercial providers for improving access to quality malaria treatment. Understanding their current role is an essential first step, notably in terms of the volume of diagnostics and anti-malarials they sell. Sales volume data can be used to measure the importance of different provider and product types, frequency of parasitological diagnosis and impact of interventions. Several methods for measuring sales volumes are available, yet all have methodological challenges and evidence is lacking on the comparability of different methods. Using sales volume data on anti-malarials and rapid diagnostic tests (RDTs) for malaria collected through provider recall (RC) and retail audits (RA), this study measures the degree of agreement between the two methods at wholesale and retail commercial providers in Cambodia following the Bland-Altman approach. Relative strengths and weaknesses of the methods were also investigated through qualitative research with fieldworkers. A total of 67 wholesalers and 107 retailers were sampled. Wholesale sales volumes were estimated through both methods for 62 anti-malarials and 23 RDTs and retail volumes for 113 anti-malarials and 33 RDTs. At wholesale outlets, RA estimates for anti-malarial sales were on average higher than RC estimates (mean difference of four adult equivalent treatment doses (95% CI 0.6-7.2)), equivalent to 30% of mean sales volumes. For RDTs at wholesalers, the between-method mean difference was not statistically significant (one test, 95% CI -6.0-4.0). At retail outlets, between-method differences for both anti-malarials and RDTs increased with larger volumes being measured, so mean differences were not a meaningful measure of agreement between the methods. Qualitative research revealed that in Cambodia where sales volumes are small, RC had key advantages: providers were perceived to remember more easily their sales volumes and find RC less invasive; fieldworkers found it more

  18. GEANT4 simulation of water volume fraction measurement in dehydrated crude oil

    Institute of Scientific and Technical Information of China (English)

    JING Chunguo; XING Guangzhong; LIU Bin

    2007-01-01

    Online measurement of water volume fraction (WVF) in dehydrated crude oil is a difficult task due to very little water in dehydrated crude oil and high precision requirements. We presents a method to measure water volume fraction in dehydrated crude oil with γ-ray densitometry. The Monte Carlo computer simulation packet GEANT4 was used to analyze the WVF measuring sensitivity of the γ-ray densitometry at different γ-ray energies, and effects of temperature, pressure, salinity and oil components on WVF measurement. The results show that the γ-ray densitome-try has high sensitivity in γ-ray energy ranges of 16~25 keV, and it can distinguish WVF changes of 0.0005. The calculated WVF decreases about 0.0002 with 1 ℃ of temperature increase and they have approximately linear relation with temperature when water volume fraction remains the same. Effects of pressure, salinity and oil components on water volume fraction can be neglected. Experiments were done to analyze sensitivity of the γ-ray densitometry. The results, as compared with simulations, demonstrate that simulation method is reliable and it is feasible to gauge low water volume fraction using low energy γ-rays.

  19. Seneca Falls: Achieving Woman's Rights. Teaching with Primary Sources Series, Volume 12.

    Science.gov (United States)

    Hodges, Elaine Prater

    This volume provides documentation on the origin of the women's rights movement placing the documents in a context that aims to show the rationale that blocked women from achieving full equality. The volume contains 127 fully annotated documents presented in chronological order (with a few exceptions) beginning in 1632 with colonial laws regarding…

  20. Measurement of testicular volume in smaller testes: how accurate is the conventional orchidometer?

    Science.gov (United States)

    Lin, Chih-Chieh; Huang, William J S; Chen, Kuang-Kuo

    2009-01-01

    The aim of this study was to evaluate the accuracy of different methods, including the Seager orchidometer (SO) and ultrasonography (US), for assessing testicular volume of smaller testes (testes volume less than 18 mL). Moreover, the equations used for the calculations--the Hansen formula (length [L] x width [W](2) x 0.52, equation A), the prolate ellipsoid formula (L x W x height [H] x 0.52, equation B), and the Lambert equation (L x W x H x 0.71, equation C)--were also examined and compared with the gold standard testicular volume obtained by water displacement (Archimedes principle). In this study, 30 testes from 15 men, mean age 75.3 (+/-8.3) years, were included. They all had advanced prostate cancer and were admitted for orchiectomy. Before the procedure, all the testes were assessed using SO and US. The dimensions were then input into each equation to obtain the volume estimates. The testicular volume by water displacement was 8.1 +/- 3.5 mL. Correlation coefficients (R(2)) of the 2 different methods (SO, US) to the gold standard were 0.70 and 0.85, respectively. The calculated testicular volumes were 9.2 +/- 3.9 mL (measured by SO, equation A), 11.9 +/- 5.2 mL (measured by SO, equation C), 7.3 +/- 4.2 mL (measured by US, equation A), 6.5 +/- 3.3 mL (measured by US, equation B) and 8.9 +/- 4.5 mL (measured by US, equation C). Only the mean size measured by US and volume calculated with the Hansen equation (equation A) and the mean size measured by US and volume calculated with the Lambert equation (equation C) showed no significant differences when compared with the volumes estimated by water displacement (mean difference 0.81 mL, P = .053, and 0.81 mL, P = .056, respectively). Based on our measurements, we categorized testicular volume by different cutoff values (7.0 mL, 7.5 mL, 8.0 mL, and 8.5 mL) to calculate a new constant for use in the Hansen equation. The new constant was 0.59. We then reexamined the equations using the new 0.59 constant, and found

  1. Revisiting the returns-volume relationship: Time variation, alternative measures and the financial crisis

    Science.gov (United States)

    Cook, Steve; Watson, Duncan

    2017-03-01

    Following its introduction in the seminal study of Osborne (1959), a voluminous literature has emerged examining the returns-volume relationship for financial assets. The present paper revisits this relationship in an examination of the FTSE100 which extends the existing literature in two ways. First, alternative daily measures of the FTSE100 index are used to create differing returns and absolute returns series to employ in an examination of returns-volume causality. Second, rolling regression analysis is utilised to explore potential time variation in the returns-volume relationship. The findings obtained depict a hitherto unconsidered complexity in this relationship with the type of returns series considered and financial crisis found to be significant underlying factors. The implications of the newly derived results for both the understanding of the nature of the returns-volume relationship and the development of theories in connection to it are discussed.

  2. Fan Noise Source Diagnostic Test: LDV Measured Flow Field Results

    Science.gov (United States)

    Podboy, Gary C.; Krupar, Martin J.; Hughes, Christopher E.; Woodward, Richard P.

    2003-01-01

    Results are presented of an experiment conducted to investigate potential sources of noise in the flow developed by two 22-in. diameter turbofan models. The R4 and M5 rotors that were tested were designed to operate at nominal take-off speeds of 12,657 and 14,064 RPMC, respectively. Both fans were tested with a common set of swept stators installed downstream of the rotors. Detailed measurements of the flows generated by the two were made using a laser Doppler velocimeter system. The wake flows generated by the two rotors are illustrated through a series of contour plots. These show that the two wake flows are quite different, especially in the tip region. These data are used to explain some of the differences in the rotor/stator interaction noise generated by the two fan stages. In addition to these wake data, measurements were also made in the R4 rotor blade passages. These results illustrate the tip flow development within the blade passages, its migration downstream, and (at high rotor speeds) its merging with the blade wake of the adjacent (following) blade. Data also depict the variation of this tip flow with tip clearance. Data obtained within the rotor blade passages at high rotational speeds illustrate the variation of the mean shock position across the different blade passages.

  3. Ultrafast Magnetism Dynamics Measure Using Tabletop Ultrafast EUV Sources

    Energy Technology Data Exchange (ETDEWEB)

    Silva, Thomas J. [NIST; Murnane, Margaret [University of Colorado

    2013-08-21

    In our work to date, we made two significant advances. First we demonstrated element-selective demagnetization dynamics for the first time, with a record time resolution for x-ray probing of 55 fs. Second, in new work, we were able to probe the timescale of the exchange interaction in magnetic materials, also for the first time. Our measurements were made using the transverse magneto-optic Kerr effect (T-MOKE) geometry, since the reflectivity of a magnetic material changes with the direction of the magnetization vector of a surface. In our experiment, we periodically reversed the magnetization direction of a grating structure made of Permalloy (Ni80Fe20) using an external magnetic field. To achieve maximum contrast, we used HHG light spanning the M-shell (3p) absorption edges of Fe and Ni. Our characterization of the static magnetization of a Permalloy sample shows high magnetic asymmetry at photon energies just above and below the absorption edges at 55 eV and 65 eV, respectively. This result is in excellent agreement with measurements done on the same using a synchrotron source.

  4. H- extraction from electron-cyclotron-resonance-driven multicusp volume source operated in pulsed mode

    Science.gov (United States)

    Svarnas, P.; Bacal, M.; Auvray, P.; Béchu, S.; Pelletier, J.

    2006-03-01

    H2 microwave (2.45GHz) pulsed plasma is produced from seven elementary electron cyclotron resonance sources installed into the magnetic multipole chamber "Camembert III" (École Polytechnique—Palaiseau) from which H- extraction takes place. The negative-ion and electron extracted currents are studied through electrical measurements and the plasma parameters by means of electrostatic probe under various experimental conditions. The role of the plasma electrode bias and the discharge duty cycle in the extraction process is emphasized. The gas breakdown at the beginning of every pulse gives rise to variations of the plasma characteristic parameters in comparison with those established at the later time of the pulse, where the electron temperature, the plasma potential, and the floating potential converge to the values obtained for a continuous plasma. The electron density is significantly enhanced in the pulsed mode.

  5. Corneal Volume Measurements with Pentacam for Detection of Keratoconus and Subclinical Keratoconus

    OpenAIRE

    Nurullah Çağıl; Nagihan Uğurlu; Hasan Basri Çakmak; Sucattin İlker Kocamış; Hüseyin Simavlı; Şaban Şimşek

    2013-01-01

    Pur po se: To estimate the sensitivity and specificity of corneal volume (CV) measurements in discriminating keratoconus and subclinical keratoconus from normal corneas. Ma te ri al and Met hod: Clinical records and Pentacam measurements of ninety-four patients with keratoconus, 36 patients with subclinical keratoconus, and 166 refractive surgery candidates with normal corneas were evaluated retrospectively. CV within 3, 5, 7, and 10 mm circles around the central cornea was measur...

  6. A Novel Technology for Measurements of Dielectric Properties of Extremely Small Volumes of Liquids

    Directory of Open Access Journals (Sweden)

    Wei-Na Liu

    2016-01-01

    Full Text Available A high sensitivity sensor for measurement radio frequency (RF dielectric permittivity of liquids is described. Interference is used and parasitic effects are cancellation, which makes the sensor can catch weak signals caused by liquids with extremely small volumes. In addition, we present the relationship between transmission coefficient and permittivity of liquids under test (LUT. Using this sensor, quantitative measurements of the dielectric properties at 5.8 GHz are demonstrated of LUTs. Experiments show that the proposed method only requires the volume of 160 nanoliters for liquids. Therefore, the technology can be used for RF spectroscopic analysis of biological samples and extremely precious liquids.

  7. E ring dust sources: Implications from Cassini's dust measurements

    Science.gov (United States)

    Spahn, Frank; Albers, Nicole; Hörning, Marcel; Kempf, Sascha; Krivov, Alexander V.; Makuch, Martin; Schmidt, Jürgen; Seiß, Martin; Miodrag Sremčević

    2006-08-01

    The Enceladus flybys of the Cassini spacecraft are changing our understanding of the origin and sustainment of Saturn's E ring. Surprisingly, beyond the widely accepted dust production caused by micrometeoroid impacts onto the atmosphereless satellites (the impactor-ejecta process), geophysical activities have been detected at the south pole of Enceladus, providing an additional, efficient dust source. The dust detector data obtained during the flyby E11 are used to identify the amount of dust produced in the impactor-ejecta process and to improve related modeling [Spahn, F., Schmidt, J., Albers, N., Hörning, M., Makuch, M., Seiß, M., Kempf, S., Srama, R., Dikarev, V.V., Helfert, S., Moragas-Klostermeyer, G., Krivov, A.V., Sremčević, M., Tuzzolino, A., Economou, T., Grün, E., 2006. Cassini dust measurements at Enceladus: implications for Saturn's E ring. Science, in press]. With this, we estimate the impact-generated dust contributions of the other E ring satellites and find significant differences in the dust ejection efficiency by two projectile families - the E ring particles (ERPs) and the interplanetary dust particles (IDPs). Together with the Enceladus south-pole source, the ERP impacts play a crucial role in the inner region, whereas the IDP impacts dominate the particle production in the outer E ring, possibly accounting for its large radial extent. Our results can be verified in future Cassini flybys of the E ring satellites. In this way poorly known parameters of the dust particle production in hypervelocity impacts can be constrained by comparison of the data and theory.

  8. Measuring and monitoring KIPT Neutron Source Facility Reactivity

    Energy Technology Data Exchange (ETDEWEB)

    Cao, Yan [Argonne National Lab. (ANL), Argonne, IL (United States); Gohar, Yousry [Argonne National Lab. (ANL), Argonne, IL (United States); Zhong, Zhaopeng [Argonne National Lab. (ANL), Argonne, IL (United States)

    2015-08-01

    Argonne National Laboratory (ANL) of USA and Kharkov Institute of Physics and Technology (KIPT) of Ukraine have been collaborating on developing and constructing a neutron source facility at Kharkov, Ukraine. The facility consists of an accelerator-driven subcritical system. The accelerator has a 100 kW electron beam using 100 MeV electrons. The subcritical assembly has keff less than 0.98. To ensure the safe operation of this neutron source facility, the reactivity of the subcritical core has to be accurately determined and continuously monitored. A technique which combines the area-ratio method and the flux-to-current ratio method is purposed to determine the reactivity of the KIPT subcritical assembly at various conditions. In particular, the area-ratio method can determine the absolute reactivity of the subcritical assembly in units of dollars by performing pulsed-neutron experiments. It provides reference reactivities for the flux-to-current ratio method to track and monitor the reactivity deviations from the reference state while the facility is at other operation modes. Monte Carlo simulations are performed to simulate both methods using the numerical model of the KIPT subcritical assembly. It is found that the reactivities obtained from both the area-ratio method and the flux-to-current ratio method are spatially dependent on the neutron detector locations and types. Numerical simulations also suggest optimal neutron detector locations to minimize the spatial effects in the flux-to-current ratio method. The spatial correction factors are calculated using Monte Carlo methods for both measuring methods at the selected neutron detector locations. Monte Carlo simulations are also performed to verify the accuracy of the flux-to-current ratio method in monitoring the reactivity swing during a fuel burnup cycle.

  9. Quantitative radiology: automated measurement of polyp volume in computed tomography colonography using Hessian matrix-based shape extraction and volume growing

    Science.gov (United States)

    Epstein, Mark L.; Obara, Piotr R.; Chen, Yisong; Liu, Junchi; Zarshenas, Amin; Makkinejad, Nazanin; Dachman, Abraham H.

    2015-01-01

    Background Current measurement of the single longest dimension of a polyp is subjective and has variations among radiologists. Our purpose was to develop a computerized measurement of polyp volume in computed tomography colonography (CTC). Methods We developed a 3D automated scheme for measuring polyp volume at CTC. Our scheme consisted of segmentation of colon wall to confine polyp segmentation to the colon wall, extraction of a highly polyp-like seed region based on the Hessian matrix, a 3D volume growing technique under the minimum surface expansion criterion for segmentation of polyps, and sub-voxel refinement and surface smoothing for obtaining a smooth polyp surface. Our database consisted of 30 polyp views (15 polyps) in CTC scans from 13 patients. Each patient was scanned in the supine and prone positions. Polyp sizes measured in optical colonoscopy (OC) ranged from 6-18 mm with a mean of 10 mm. A radiologist outlined polyps in each slice and calculated volumes by summation of volumes in each slice. The measurement study was repeated 3 times at least 1 week apart for minimizing a memory effect bias. We used the mean volume of the three studies as “gold standard”. Results Our measurement scheme yielded a mean polyp volume of 0.38 cc (range, 0.15-1.24 cc), whereas a mean “gold standard” manual volume was 0.40 cc (range, 0.15-1.08 cc). The “gold-standard” manual and computer volumetric reached excellent agreement (intra-class correlation coefficient =0.80), with no statistically significant difference [P (F≤f) =0.42]. Conclusions We developed an automated scheme for measuring polyp volume at CTC based on Hessian matrix-based shape extraction and volume growing. Polyp volumes obtained by our automated scheme agreed excellently with “gold standard” manual volumes. Our fully automated scheme can efficiently provide accurate polyp volumes for radiologists; thus, it would help radiologists improve the accuracy and efficiency of polyp volume

  10. AFM-porosimetry: density and pore volume measurements of particulate materials.

    Science.gov (United States)

    Sörensen, Malin H; Valle-Delgado, Juan J; Corkery, Robert W; Rutland, Mark W; Alberius, Peter C

    2008-06-01

    We introduced the novel technique of AFM-porosimetry and applied it to measure the total pore volume of porous particles with a spherical geometry. The methodology is based on using an atomic force microscope as a balance to measure masses of individual particles. Several particles within the same batch were measured, and by plotting particle mass versus particle volume, the bulk density of the sample can be extracted from the slope of the linear fit. The pore volume is then calculated from the densities of the bulk and matrix materials, respectively. In contrast to nitrogen sorption and mercury porosimetry, this method is capable of measuring the total pore volume regardless of pore size distribution and pore connectivity. In this study, three porous samples were investigated by AFM-porosimetry: one ordered mesoporous sample and two disordered foam structures. All samples were based on a matrix of amorphous silica templated by a block copolymer, Pluronic F127, swollen to various degrees with poly(propylene glycol). In addition, the density of silica spheres without a template was measured by two independent techniques: AFM and the Archimedes principle.

  11. Relations between various measures of iodine intake and thyroid volume, thyroid nodularity, and serum thyroglobulin

    DEFF Research Database (Denmark)

    Rasmussen, Lone Banke; Ovesen, L.; Bulow, I.

    2002-01-01

    plus supplements, iodine intake from diet/kg body wt, and milk intake (P = 0.001 for all), but not urinary iodine excretion measured as a concentration (P = 0.40). All measures of iodine intake were significantly related to serum thyroglobulin concentration (P less than or equal to 0.002), but only...... excretion measured as a urinary concentration, predicted thyroid volume. Serum thyroglobulin concentration appears to be a good marker of iodine status. Subgroups with low intakes of milk and milk products had an increased risk of thyroid disease.......Background: Iodine intake can be measured in various ways, and each method may have advantages and disadvantages. Objective: We sought to investigate the potential associations of various measures of iodine intake with thyroid volume, prevalence of thyroid nodules, and serum thyroglobulin. We also...

  12. Mobile measurements of aerosol number and volume size distributions in an Alpine valley: Influence of traffic versus wood burning

    Science.gov (United States)

    Weimer, S.; Mohr, C.; Richter, R.; Keller, J.; Mohr, M.; Prévôt, A. S. H.; Baltensperger, U.

    The spatial variability of highly time resolved size distributions was investigated in a narrow valley which provides the opportunity to study the impact of different sources on ambient particle concentrations during summer and winter time. The measurements were performed with a Fast Mobility Particle Sizer (FMPS) from TSI, Inc. on a mobile laboratory in Southern Switzerland. The results indicate enhanced number concentrations (between 150 000 and 500 000 cm -3) along the busy highway A2 which is the main transit route through the Swiss Alps connecting the northern and southern part of Switzerland. Especially the nanoparticles with diameters lower than 30 nm showed strongly increased number concentrations on the highway both in summer and winter. In winter time, high aerosol volume concentrations (PM 0.3) were found in villages where wood burning is often used for heating purposes. Both traffic and wood burning were found to be important sources for particulate mass which accumulates during temperature inversions in winter time. Traffic was the dominant and wood burning a minor source for the nanoparticle number concentration. This is important regarding health impacts and its attribution to different sources because wood burning might contribute most to particulate mass whereas at the same time and place traffic contributes most to particulate number. In addition, during summer time volatility measurements were performed with the FMPS showing that the nucleation mode prevalently seen on the highway was removed by more than 95% by thermal treatment.

  13. A fibre optic scintillator dosemeter for absorbed dose measurements of low-energy X-ray-emitting brachytherapy sources.

    Science.gov (United States)

    Sliski, Alan; Soares, Christopher; Mitch, Michael G

    2006-01-01

    A newly developed dosemeter using a 0.5 mm diameter x 0.5 mm thick cylindrical plastic scintillator coupled to the end of a fibre optic cable is capable of measuring the absorbed dose rate in water around low-activity, low-energy X-ray emitters typically used in prostate brachytherapy. Recent tests of this dosemeter showed that it is possible to measure the dose rate as a function of distance in water from 2 to 30 mm of a (103)Pd source of air-kerma strength 3.4 U (1 U = 1 microGy m(2) h(-1)), or 97 MBq (2.6 mCi) apparent activity, with good signal-to-noise ratio. The signal-to-noise ratio is only dependent on the integration time and background subtraction. The detector volume is enclosed in optically opaque, nearly water-equivalent materials so that there is no polar response other than that due to the shape of the scintillator volume chosen, in this case cylindrical. The absorbed dose rate very close to commercial brachytherapy sources can be mapped in an automated water phantom, providing a 3-D dose distribution with sub-millimeter spatial resolution. The sensitive volume of the detector is 0.5 mm from the end of the optically opaque waterproof housing, enabling measurements at very close distances to sources. The sensitive detector electronics allow the measurement of very low dose rates, as exist at centimeter distances from these sources. The detector is also applicable to mapping dose distributions from more complex source geometries such as eye applicators for treating macular degeneration.

  14. Ultrasonic methods for measuring liquid viscosity and volume percent of solids

    Energy Technology Data Exchange (ETDEWEB)

    Sheen, S.H.; Chien, H.T.; Raptis, A.C.

    1997-02-01

    This report describes two ultrasonic techniques under development at Argonne National Laboratory (ANL) in support of the tank-waste transport effort undertaken by the U.S. Department of Energy in treating low-level nuclear waste. The techniques are intended to provide continuous on-line measurements of waste viscosity and volume percent of solids in a waste transport line. The ultrasonic technique being developed for waste-viscosity measurement is based on the patented ANL viscometer. Focus of the viscometer development in this project is on improving measurement accuracy, stability, and range, particularly in the low-viscosity range (<30 cP). A prototype instrument has been designed and tested in the laboratory. Better than 1% accuracy in liquid density measurement can be obtained by using either a polyetherimide or polystyrene wedge. To measure low viscosities, a thin-wedge design has been developed and shows good sensitivity down to 5 cP. The technique for measuring volume percent of solids is based on ultrasonic wave scattering and phase velocity variation. This report covers a survey of multiple scattering theories and other phenomenological approaches. A theoretical model leading to development of an ultrasonic instrument for measuring volume percent of solids is proposed, and preliminary measurement data are presented.

  15. The Munich Compact Light Source: initial performance measures.

    Science.gov (United States)

    Eggl, Elena; Dierolf, Martin; Achterhold, Klaus; Jud, Christoph; Günther, Benedikt; Braig, Eva; Gleich, Bernhard; Pfeiffer, Franz

    2016-09-01

    While large-scale synchrotron sources provide a highly brilliant monochromatic X-ray beam, these X-ray sources are expensive in terms of installation and maintenance, and require large amounts of space due to the size of storage rings for GeV electrons. On the other hand, laboratory X-ray tube sources can easily be implemented in laboratories or hospitals with comparatively little cost, but their performance features a lower brilliance and a polychromatic spectrum creates problems with beam hardening artifacts for imaging experiments. Over the last decade, compact synchrotron sources based on inverse Compton scattering have evolved as one of the most promising types of laboratory-scale X-ray sources: they provide a performance and brilliance that lie in between those of large-scale synchrotron sources and X-ray tube sources, with significantly reduced financial and spatial requirements. These sources produce X-rays through the collision of relativistic electrons with infrared laser photons. In this study, an analysis of the performance, such as X-ray flux, source size and spectra, of the first commercially sold compact light source, the Munich Compact Light Source, is presented.

  16. An open source workflow for 3D printouts of scientific data volumes

    Science.gov (United States)

    Loewe, P.; Klump, J. F.; Wickert, J.; Ludwig, M.; Frigeri, A.

    2013-12-01

    As the amount of scientific data continues to grow, researchers need new tools to help them visualize complex data. Immersive data-visualisations are helpful, yet fail to provide tactile feedback and sensory feedback on spatial orientation, as provided from tangible objects. The gap in sensory feedback from virtual objects leads to the development of tangible representations of geospatial information to solve real world problems. Examples are animated globes [1], interactive environments like tangible GIS [2], and on demand 3D prints. The production of a tangible representation of a scientific data set is one step in a line of scientific thinking, leading from the physical world into scientific reasoning and back: The process starts with a physical observation, or from a data stream generated by an environmental sensor. This data stream is turned into a geo-referenced data set. This data is turned into a volume representation which is converted into command sequences for the printing device, leading to the creation of a 3D printout. As a last, but crucial step, this new object has to be documented and linked to the associated metadata, and curated in long term repositories to preserve its scientific meaning and context. The workflow to produce tangible 3D data-prints from science data at the German Research Centre for Geosciences (GFZ) was implemented as a software based on the Free and Open Source Geoinformatics tools GRASS GIS and Paraview. The workflow was successfully validated in various application scenarios at GFZ using a RapMan printer to create 3D specimens of elevation models, geological underground models, ice penetrating radar soundings for planetology, and space time stacks for Tsunami model quality assessment. While these first pilot applications have demonstrated the feasibility of the overall approach [3], current research focuses on the provision of the workflow as Software as a Service (SAAS), thematic generalisation of information content and

  17. Relation of the volume of the olfactory bulb to psychophysical measures of olfactory function.

    Science.gov (United States)

    Mazal, Patricia Portillo; Haehner, Antje; Hummel, Thomas

    2016-01-01

    The aim of this review is to investigate whether changes in olfactory bulb volume relate to changes in specific olfactory functions. We studied currently available peer-reviewed articles on the volume of the human olfactory bulb that also included a psychophysical measure of olfactory function. In the present review, we observed a very clear and consistent correlation between general olfactory function and olfactory bulb (OB) volume. We were not able to find a clear relationship between a specific smell component and OB volume, even when analyzing pathologic conditions separately. In some cases, changes were observed for different subtests, but these changes did not significantly correlate with OB volume or had only a borderline correlation. In other cases, we found contradictory data. Several factors may contribute to the difficulties in finding correlations with the different components of smell: (1) the OB volume may be influenced by information from olfactory receptor neurons (bottom-up effect), information from central nervous system (top-down effect) and by direct damage; (2) most pathologic conditions affect more than one area of the olfactory pathway; (3) small sample sizes of hyposmic subjects were used. We believe that it is necessary to do further studies with larger numbers of subjects to answer the currently investigated question.

  18. Measuring the Sources of the Intergalactic Ionizing Flux

    Science.gov (United States)

    Cowie, L. L.; Barger, A. J.; Trouille, L.

    2009-02-01

    We use a wide-field (0.9 deg2) X-ray sample with optical and Galaxy Evolution Explorer (GALEX) ultraviolet observations to measure the contribution of active galactic nuclei (AGNs) to the ionizing flux as a function of redshift. Our analysis shows that the AGN contribution to the metagalactic ionizing background peaks at around z = 2. The measured values of the ionizing background from the AGNs are lower than previous estimates and confirm that ionization from AGNs is insufficient to maintain the observed ionization of the intergalactic medium (IGM) at z > 3. We show that only X-ray sources with broad lines in their optical spectra have detectable ionizing flux and that the ionizing flux seen in an AGN is not correlated with its X-ray color. We also use the GALEX observations of the GOODS-N region to place a 2σ upper limit of 0.008 on the average ionization fraction f ν(700 Å)/f ν(1500 Å) for 626 UV selected galaxies in the redshift range z = 0.9-1.4. We then use this limit to estimate an upper bound to the galaxy contribution in the redshift range z = 0-5. If the z ~ 1.15 ionization fraction is appropriate for higher-redshift galaxies, then contributions from the galaxy population are also too low to account for the IGM ionization at the highest redshifts (z > 4). Based in part on data obtained at the W. M. Keck Observatory, which is operated as a scientific partnership among the California Institute of Technology, the University of California, and NASA and was made possible by the generous financial support of the W. M. Keck Foundation.

  19. Sources of variability in musculo-articular stiffness measurement.

    Science.gov (United States)

    Ditroilo, Massimiliano; Watsford, Mark; Murphy, Aron; De Vito, Giuseppe

    2013-01-01

    The assessment of musculo-articular stiffness (MAS) with the free-oscillation technique is a popular method with a variety of applications. This study examined the sources of variability (load applied and frequency of oscillation) when MAS is assessed. Over two testing occasions, 14 healthy men (27.7±5.2 yr, 1.82±0.04 m, 79.5±8.4 kg) were measured for isometric maximum voluntary contraction and MAS of the knee flexors using submaximal loads relative to the individual's maximum voluntary contraction (MAS%MVC) and a single absolute load (MASABS). As assessment load increased, MAS%MVC (coefficient of variation (CV)  =  8.1-12.1%; standard error of measurement (SEM)  =  51.6-98.8 Nm⁻¹) and frequency (CV  =  4.8-7.0%; SEM  =  0.060-0.075 s⁻¹) variability increased consequently. Further, similar levels of variability arising from load (CV  =  6.7%) and frequency (CV  =  4.8-7.0%) contributed to the overall MAS%MVC variability. The single absolute load condition yielded better reliability scores for MASABS (CV  =  6.5%; SEM  =  40.2 Nm⁻¹) and frequency (CV  =  3.3%; SEM  =  0.039 s⁻¹). Low and constant loads for MAS assessment, which are particularly relevant in the clinical setting, exhibited superior reliability compared to higher loads expressed as a percentage of maximum voluntary contraction, which are more suitable for sporting situations. Appropriate sample size and minimum detectable change can therefore be determined when prospective studies are carried out.

  20. Measurement of track structure parameters of low and medium energy helium and carbon ions in nanometric volumes

    Science.gov (United States)

    Hilgers, G.; Bug, M. U.; Rabus, H.

    2017-10-01

    Ionization cluster size distributions produced in the sensitive volume of an ion-counting wall-less nanodosimeter by monoenergetic carbon ions with energies between 45 MeV and 150 MeV were measured at the TANDEM-ALPI ion accelerator facility complex of the LNL-INFN in Legnaro. Those produced by monoenergetic helium ions with energies between 2 MeV and 20 MeV were measured at the accelerator facilities of PTB and with a 241Am alpha particle source. C3H8 was used as the target gas. The ionization cluster size distributions were measured in narrow beam geometry with the primary beam passing the target volume at specified distances from its centre, and in broad beam geometry with a fan-like primary beam. By applying a suitable drift time window, the effective size of the target volume was adjusted to match the size of a DNA segment. The measured data were compared with the results of simulations obtained with the PTB Monte Carlo code PTra. Before the comparison, the simulated cluster size distributions were corrected with respect to the background of additional ionizations produced in the transport system of the ionized target gas molecules. Measured and simulated characteristics of the particle track structure are in good agreement for both types of primary particles and for both types of the irradiation geometry. As the range in tissue of the ions investigated is within the typical extension of a spread-out Bragg peak, these data are useful for benchmarking not only ‘general purpose’ track structure simulation codes, but also treatment planning codes used in hadron therapy. Additionally, these data sets may serve as a data base for codes modelling the induction of radiation damages at the DNA-level as they almost completely characterize the ionization component of the nanometric track structure.

  1. Research Note Difference between low-volume and high-volume Andersen samplers in measuring atmospheric aerosols

    Institute of Scientific and Technical Information of China (English)

    Fengfu Fu; Nobuo Shinohaya; Mitsuo Ito; Xueqin Xu; Mincong Shen; Liangjun Xu

    2008-01-01

    The mass concentration and size distribution of aerosols in Tokaimura were investigated using a high-volume and a low-volume Andersen sampler. A difference was found using the two samplers: the concentration of total aerosols determined with the high-volume sampler is smaller than that of the low-volume sampler by 70-90% throughout the year. Compared to the high-volume sampler, low-volume sampler gave lower concentration for aerosols7μm, higher concentration for aerosols of 3.3-7.0μm and<1.1μm, though similar results for aerosols of 1.1-3.3μm. The low-volume sampler was found to have better separation efficiency and higher accuracy.

  2. VUV emission spectroscopy combined with H- density measurements in the ion source Prometheus I

    Science.gov (United States)

    Aleiferis, S.; Laulainen, J.; Svarnas, P.; Tarvainen, O.; Bacal, M.; Béchu, S.

    2017-08-01

    "Prometheus I" is a volume H- negative ion source, driven by a network of dipolar electron cyclotron resonance (ECR; 2.45 GHz) modules. The vacuum-ultraviolet (VUV) emission spectrum of low-temperature hydrogen plasmas may be related to molecular and atomic processes involved directly or indirectly in the production of negative ions. In this work, VUV spectroscopy has been performed in the above source, Prometheus I, both in the ECR zones and the bulk (far from ECR zones and surfaces) plasma. The acquired VUV spectra are correlated with the negative ion densities, as measured by means of laser photodetachment, and the possible mechanisms of negative ion production are considered. The well-established H- formation process of dissociative attachment to vibrationally excited molecules is evaluated, while an additional production path (i.e. neutral resonant ionization) is tested due to the recently attracted interest. The obtained results indicate that for the source Prometheus I, the dominant formation process is dissociative attachment.

  3. The error analysis of Lobular and segmental division of right liver by volume measurement.

    Science.gov (United States)

    Zhang, Jianfei; Lin, Weigang; Chi, Yanyan; Zheng, Nan; Xu, Qiang; Zhang, Guowei; Yu, Shengbo; Li, Chan; Wang, Bin; Sui, Hongjin

    2017-07-01

    The aim of this study is to explore the inconsistencies between right liver volume as measured by imaging and the actual anatomical appearance of the right lobe. Five healthy donated livers were studied. The liver slices were obtained with hepatic segments multicolor-infused through the portal vein. In the slices, the lobes were divided by two methods: radiological landmarks and real anatomical boundaries. The areas of the right anterior lobe (RAL) and right posterior lobe (RPL) on each slice were measured using Photoshop CS5 and AutoCAD, and the volumes of the two lobes were calculated. There was no statistically significant difference between the volumes of the RAL or RPL as measured by the radiological landmarks (RL) and anatomical boundaries (AB) methods. However, the curves of the square error value of the RAL and RPL measured using CT showed that the three lowest points were at the cranial, intermediate, and caudal levels. The U- or V-shaped curves of the square error rate of the RAL and RPL revealed that the lowest value is at the intermediate level and the highest at the cranial and caudal levels. On CT images, less accurate landmarks were used to divide the RAL and RPL at the cranial and caudal layers. The measured volumes of hepatic segments VIII and VI would be less than their true values, and the measured volumes of hepatic segments VII and V would be greater than their true values, according to radiological landmarks. Clin. Anat. 30:585-590, 2017. © 2017 Wiley Periodicals, Inc. © 2017 Wiley Periodicals, Inc.

  4. Calculation of the Residual Blood Volume after Acute, Non-Ongoing Hemorrhage Using Serial Hematocrit Measurements and the Volume of Isotonic Fluid Infused: Theoretical Hypothesis Generating Study.

    Science.gov (United States)

    Oh, Won Sup; Chon, Sung-Bin

    2016-05-01

    Fluid resuscitation, hemostasis, and transfusion is essential in care of hemorrhagic shock. Although estimation of the residual blood volume is crucial, the standard measuring methods are impractical or unsafe. Vital signs, central venous or pulmonary artery pressures are inaccurate. We hypothesized that the residual blood volume for acute, non-ongoing hemorrhage was calculable using serial hematocrit measurements and the volume of isotonic solution infused. Blood volume is the sum of volumes of red blood cells and plasma. For acute, non-ongoing hemorrhage, red blood cell volume would not change. A certain portion of the isotonic fluid would increase plasma volume. Mathematically, we suggest that the residual blood volume after acute, non-ongoing hemorrhage might be calculated as 0·25N/[(Hct1/Hct2)-1], where Hct1 and Hct2 are the initial and subsequent hematocrits, respectively, and N is the volume of isotonic solution infused. In vivo validation and modification is needed before clinical application of this model.

  5. A CO2 laser based two-volume collective scattering instrument for spatially localized turbulence measurements

    DEFF Research Database (Denmark)

    Saffman, Mark; Zoletnik, S.; Basse, Nils Plesner

    2001-01-01

    We describe and demonstrate a two-volume collective scattering system for localized measurements of plasma turbulence. The finite crossfield correlation length of plasma turbulence combined with spatial variations in the magnetic field direction are used to obtain spatially localized turbulence...

  6. Technical Note: Stored grain volume measurement using a low density point cloud

    Science.gov (United States)

    The mass of stored grain is often determined from volume measurements by crop insurers, government auditors, and stored grain managers conducting inventories. Recent increases in bin size have accentuated the difficulty of accounting for irregularities and variations in surface conditions in calcula...

  7. Quantitative measure for the "nakedness" of fluoride ion sources.

    Science.gov (United States)

    Christe, Karl O; Jenkins, H Donald Brooke

    2003-08-01

    A quantitative measure for the donor strength or "nakedness" of fluoride ion donors is presented. It is based on the free energy change associated with the transfer of a fluoride ion from the donor to a given acceptor molecule. Born-Haber cycle calculations were used to calculate both the free energy and the enthalpy change for this process. The enthalpy change is given by the sum of the fluoride ion affinity of the acceptor (as defined in strict thermodynamic convention) and the lattice energy difference (DeltaU(POT)) between the fluoride ion donor and the salt formed with the acceptor. Because, for a given acceptor, the fluoride affinity has a constant value, the relative enthalpy (and also the corresponding free energy) changes are governed exclusively by the lattice energy differences. In this study, BF(3), PF(5), AsF(5), and SbF(5) were used as the acceptors, and the following seven fluoride ion donors were evaluated: CsF, N(CH(3))(4)F (TMAF), N-methylurotropinium fluoride (MUF), hexamethylguanidinium fluoride (HMGF), hexamethylpiperidinium fluoride (HMPF), N,N,N-trimethyl-1-adamantylammonium fluoride (TMAAF), and hexakis(dimethylamino)phosphazenium fluoride (HDMAPF). Smooth relationships between the enthalpy changes and the molar volumes of the donor cations were found which asymptotically approach constant values for infinitely large cations. Whereas CsF is a relatively poor F(-) donor [(U(POT)(CsF) - U(POT)(CsSbF(6))) = 213 kJ mol(-)(1)], when compared to N(CH(3))(4)F [(U(POT)(TMAF) - U(POT)(TMASbF(6))) = 69 kJ mol(-)(1)], a 4 times larger cation (phosphazenium salt) and an infinitely large cation are required to decrease DeltaU(POT) to 17 and 0 kJ mol(-)(1), respectively. These results clearly demonstrate that very little is gained by increasing the cation size past a certain level and that secondary factors, such as chemical and physical properties, become overriding considerations.

  8. Is the difference in the volume of the pharyngeal space, as measured by acoustic pharyngometry, before and after tonsillectomy proportional to the volume of the excised tonsils?

    Directory of Open Access Journals (Sweden)

    Renata C. Di Francesco

    Full Text Available OBJECTIVE: Adenotonsillectomy is recognized as an effective therapy for snoring and sleep disorders in children. It is important to understand whether adenotonsillectomy significantly increases the volume of the pharyngeal space. The goal of this study was to evaluate the change in oropharyngeal volume after adenotonsillectomy and the correlation of this change with the objective volume of the tonsils and body mass index. METHODS: We included 27 subjects (14 males with snoring caused by tonsil and adenoid hypertrophy. The mean age of the subjects was 7.92 (±2.52 years. Children with craniofacial malformations or neuromuscular diseases or syndromes were excluded. The parents/caregivers answered an adapted questionnaire regarding sleep-disordered breathing. All patients were subjected to weight and height measurements and body mass index was calculated. The subjects underwent pharyngometry before and after adenotonsillectomy and the volume of both excised tonsils together was measured in cm3 in the operating room. RESULTS: Pharyngometric analysis showed that the mean pharyngeal volume was 28.63 (±5.57 cm3 before surgery and 31.23 (±6.76 cm3 after surgery; the volume of the oropharynx was significantly increased post-surgery (p=0.015, Wilcoxon test. No correlation was found between the objective tonsil volume and the post-surgical volume increase (p=0.6885. There was a fair correlation between the oropharyngeal volume and body mass index (p=0.0224. CONCLUSION: Adenotonsillectomy increases the volume of the pharyngeal space, but this increase does not correlate with the objective tonsil size. Furthermore, greater BMI was associated with a smaller increase in the pharyngeal volume. Oropharyngeal structures and craniofacial morphology may also play a role in the increase in oropharyngeal volume.

  9. Development of ultrasonic velocity profile method for flow rate measurements of power plant (effect of measurement volume on turbulent flow measurement)

    Energy Technology Data Exchange (ETDEWEB)

    Hiroshige, Kikura; Gentaro, Yamanaka; Tsuyoshi, Taishi; Masanori, Aritomi [Tokyo Institute of Technology, Tokyo (Japan); Yasushi, Takeda [Paul Scherrer Inst. (PSI), Villigen (Switzerland); Michitsugu, Mori [Tokyo Electric Power Co., Inc. (Japan)

    2001-07-01

    Ultrasonic Velocity Profile method has many advantages for flow rate measurement of power plant over the conventional flow measurement methods, such as measurement of the instantaneous velocity profile along the measuring line and its applicability to opaque liquids. Furthermore, the method has an advantage of being non-intrusive. Hence, it is applicable to various flow conditions, although it requires a relatively large measurement volume. In this paper, the effects of the measurement volume on the mean velocity profile for flow rate measurements of power plant and the Reynolds stress measurement have been investigated for fully developed turbulent pipe flows in a vertical pipe. The results are then compared with data obtained by Direct Numerical Simulation (DNS). (authors)

  10. Validation of Respiratory Inductance Plethysmography for Measuring Tidal Volume in Swine

    OpenAIRE

    2015-01-01

    Measuring tidal volume (VT) in nonintubated swine or swine with leaking breathing circuits is challenging. The aim of this study was to validate respiratory inductance plethysmography (RIP) for measuring VT in swine that are comparable in size to adult humans. To determine calibration curves, VT and RIP readings were obtained from anesthetized swine (n = 8; weight, 46–50 kg) during positive-pressure (mechanical) ventilation and spontaneous breathing. For positive-pressure ventilation, 6 pigs ...

  11. Sonographic Parameters for Prediction of Miscarriage: Role of 3-Dimensional Volume Measurement.

    Science.gov (United States)

    Wie, Jeong Ha; Choe, Suyearn; Kim, Sa Jin; Shin, Jong Chul; Kwon, Ji Young; Park, In Yang

    2015-10-01

    To evaluate the value of volume measurement using 3-dimensional sonography for prediction of miscarriage. We prospectively enrolled 188 singleton pregnant women at 5 to 9 weeks' gestation. The 3-dimensional sonographic gestational sac volume and yolk sac volume were measured together with the fetal heart rate, gestational sac diameter, and yolk sac diameter. For each sonographic parameter, nomograms were created; z scores were calculated for each measurement, and the values were compared between miscarriage and ongoing pregnancy groups. Sonographic parameters for prediction of miscarriage were evaluated by multivariate analysis, and the screening performance was assessed by a receiver operating characteristic curve. Among the 188 pregnancies, 30 (16.0%) had miscarriage. Multivariate analysis showed that fetal heart rate below the 5th percentile (odds ratio, 6.43), gestational sac diameter below the 5th percentile (odds ratio, 4.87), gestational sac volume below the 5th percentile (odds ratio, 5.25), and yolk sac diameter below the 2.5th or above the 97.5th percentile (odds ratio, 15.86) were significant predictors of miscarriage (P = .018; P = .018; P = .033; and P < .001, respectively). At a false-positive rate of 30%, the detection rate for miscarriage in screening by a combination of fetal heart rate, gestational sac diameter, gestational sac volume, and yolk sac diameter was 77.8%. A small-for-gestational-age gestational sac volume is a significant sonographic predictor of miscarriage, as are fetal bradycardia, a small gestational sac diameter, and a small or large yolk sac diameter. © 2015 by the American Institute of Ultrasound in Medicine.

  12. DIAGNOdent measurements and correlation with the depth and volume of minimally invasive cavity preparations.

    Science.gov (United States)

    Hamilton, James C; Gregory, William A; Valentine, John B

    2006-01-01

    In this clinical study, DIAGNOdent (KaVo) was used to assess previously diagnosed carious lesions in the pits and fissures of first and second molars. The measurements from this device were correlated with the depth and volume of the cavity preparations that resulted from minimal intervention to remove occlusal carious lesions. Twenty-five patients, 18 years of age and older, who were previously scheduled for an occlusal restoration due to caries, were recruited and enrolled in this clinical study. These patients had 48 qualifying teeth without previous restorations, sealants or other carious lesions. The occlusal surface of each study tooth was cleaned utilizing ProphyFlex2 (KaVo). Two dentists separately traced the pit and fissure system of each tooth using DIAGNOdent for two 15-second periods each. The peak reading of each of the four measurements was recorded. An impression of the occlusal surface of each tooth was recorded with a polyvinyl siloxane bite registration material. The carious lesions were removed with an air abrasion unit employing a 0.015-inch nozzle opening utilizing minimal operative intervention. A low viscosity polyvinyl siloxane was used to take an impression of the cavity preparation impression, using the bite registration impression to form the occlusal surface of the preparation impression. The preparation impression volume was calculated from its weight, using the known density of the impression material. The greatest depth of the preparation was measured. The Pearson correlation coefficient was used to investigate any relationship between depth or volume of the preparation impression and the DIAGNOdent measurements. The correlation for preparation volume and maximum DIAGNOdent measurement was 0.191 (p = 0.189). Other logical subsets of cases also did not result in any statistically significant correlations between the DIAGNOdent readings and the depth or volume of the final cavity preparations.

  13. Bymixer provides on-line calibration of measurement of CO2 volume exhaled per breath.

    Science.gov (United States)

    Breen, P H; Serina, E R

    1997-01-01

    The measurement of CO2 volume exhaled per breath (VCO2.br) can be determined during anesthesia by the multiplication and integration of tidal flow (V) and PCO2. During side-stream capnometry, PCO2 must be advanced in time by transport delay (TD), the time to suction gas through the sampling tube. During ventilation, TD can vary due to sample line connection internal volume or flow rate changes. To determine correct TD and measure accurate VCO2.br during actual ventilation. TD can be iteratively adjusted (TDADJ) until VCO2-br/tidal volume equals PCO2 measured in a mixed expired gas collection (PECO2) (J Appl. Physiol. 72:2029-2035, 1992). However. PECO2 is difficult to measure during anesthesia because CO2 is absorbed in the circle circuit. Accordingly, we implemented a bypass flow-mixing chamber device (bymixer) that was interposed in the expiration limb of the circle circuit and accurately measured PECO2 over a wide range of conditions of ventilation of a test lung-metabolic chamber (regression slope = 1.01: R2 = 0.99). The bymixer response (time constant) varied from 18.1 +/- 0.03 sec (12.5 l/min ventilation) to 66.7 +/- 0.9 sec (2.5 l/min). Bymixer PECO2 was used to correctly determine TDADJ (without interrupting respiration) to enable accurate measurement of VCO2.br over widely changing expiratory flow patterns.

  14. Mexico City air quality research initiative. Volume IV. Characterization and measurement

    Energy Technology Data Exchange (ETDEWEB)

    Mauzy, A. [ed.

    1994-04-01

    This volume describes the methods and the data gathered in an attempt to measure and characterize the meteorological factors and the concentration of different pollutants in the Mexico City Metropolitan Area. The main objective of this document was to provide input for the simulation models and to obtain information that could be used to test and improve the models` performance. Four field campaigns were conducted, as well as routine monitoring, in order to obtain a database of atmospheric dynamics and air pollution characteristics. Sections include Airborne measurements, Remote sensing measurements, and Traditional (in situ) measurements.

  15. Spatial Visualization Tasks To Support Students’ Spatial Structuring In Learning Volume Measurement

    Directory of Open Access Journals (Sweden)

    Shintia Revina

    2011-07-01

    Full Text Available Many prior researches found that most of students in grade five tendedto have difficulty in fully grasping the concept of volume measurementbecause they have to build their competence in spatial structuring. The unit of volume “packing” measurement must be integrated andcoordinated in three-dimension. On the other hand, it is revealed theerrors that students made on the volume measurement tasks with threedimensional cube arrays are related to some aspects of spatialvisualization, such as the skill to "read off" two-dimensionalrepresentation of solid objects. For those reasons, this research is aimed to develop classroom activities with the use of spatial visualization tasks to support students’ spatial structuring in learning volume measurement. Consequently, design research was chosen as an appropriate means to achieve this research goal. In this research, a sequence of instructional activities is designed and developed based on the hypothesis of students’ learning processes. This research was conducted in grade 5 of SD Pupuk Sriwijaya Palembang, Indonesia

  16. Visceral adipose tissue area measurement at a single level: can it represent visceral adipose tissue volume?

    Science.gov (United States)

    Noumura, Yusuke; Kamishima, Tamotsu; Sutherland, Kenneth; Nishimura, Hideho

    2017-08-01

    Measurement of visceral adipose tissue (VAT) needs to be accurate and sensitive to change for risk monitoring. The purpose of this study is to determine the CT slice location where VAT area can best reflect changes in VAT volume and body weight. 60 plain abdominal CT images from 30 males [mean age (range) 51 (41-68) years, mean body weight (range) 71.1 (101.9-50.9) kg] who underwent workplace screenings twice within a 1-year interval were evaluated. Automatically calculated and manually corrected areas of the VAT of various scan levels using "freeform curve" region of interest on CT were recorded and compared with body weight changes. The strongest correlations of VAT area with VAT volume and body weight changes were shown in a slice 3 cm above the lower margin of L3 with r values of 0.853 and 0.902, respectively. VAT area measurement at a single level 3 cm above the lower margin of the L3 vertebra is feasible and can reflect changes in VAT volume and body weight. Advances in knowledge: As VAT area at a CT slice 3cm above the lower margin of L3 can best reflect interval changes in VAT volume and body weight, VAT area measurement should be selected at this location.

  17. Reliable measurements for an image-derived sample volume in an open-configuration MR system

    Science.gov (United States)

    Han, Bong Soo; Lee, Man Woo; Hong, Cheolpyo

    2016-11-01

    Open-configuration magnetic resonance (MR) systems are becoming desirable for volume measurements of off-center samples due to their non-claustrophobic system configuration, excellent soft-tissue contrast, high efficiency, and low-cost. However, geometric distortion is produced by the unwanted background magnetic field and hinders volume measurements. The present study describes the characteristics of geometric distortion in off-center samples such as the thigh muscle and adipose tissue measurements using an open-type MR system. The American Association of Physicists in Medicine uniformity and linearity phantom was used for the detection and the evaluation of the geometric distortion. The geometric distortion decreased near the isocenter and increased toward the off-center. A cylindrical phantom image was acquired at the isocenter and was used as the distortion-free, reference image. Two cylindrical phantoms were scanned off-center at a position analogous to that of the human thigh. The differences between the two cylindrical phantom volumes and the reference volume were 1.62 % ± 0.16 and 5.18 % ± 0.14. Off-center-related MR imaging requires careful consideration for image interpretation and volumetric assessment of tissue.

  18. Accurate mass replacement method for the sediment concentration measurement with a constant volume container

    Science.gov (United States)

    Ban, Yunyun; Chen, Tianqin; Yan, Jun; Lei, Tingwu

    2017-04-01

    The measurement of sediment concentration in water is of great importance in soil erosion research and soil and water loss monitoring systems. The traditional weighing method has long been the foundation of all the other measuring methods and instrument calibration. The development of a new method to replace the traditional oven-drying method is of interest in research and practice for the quick and efficient measurement of sediment concentration, especially field measurements. A new method is advanced in this study for accurately measuring the sediment concentration based on the accurate measurement of the mass of the sediment-water mixture in the confined constant volume container (CVC). A sediment-laden water sample is put into the CVC to determine its mass before the CVC is filled with water and weighed again for the total mass of the water and sediments in the container. The known volume of the CVC, the mass of sediment-laden water, and sediment particle density are used to calculate the mass of water, which is replaced by sediments, therefore sediment concentration of the sample is calculated. The influence of water temperature was corrected by measuring water density to determine the temperature of water before measurements were conducted. The CVC was used to eliminate the surface tension effect so as to obtain the accurate volume of water and sediment mixture. Experimental results showed that the method was capable of measuring the sediment concentration from 0.5 up to 1200 kg m‑3. A good liner relationship existed between the designed and measured sediment concentrations with all the coefficients of determination greater than 0.999 and the averaged relative error less than 0.2%. All of these seem to indicate that the new method is capable of measuring a full range of sediment concentration above 0.5 kg m‑3 to replace the traditional oven-drying method as a standard method for evaluating and calibrating other methods.

  19. Validity and intra- and interobserver reliability of an indirect volume measurements in patients with upper extremity lymphedema

    NARCIS (Netherlands)

    Meijer, R.S.; Rietman, J.S.; Geertzen, J.H.B.; Bosmans, J.C.; Dijkstra, P.U.

    2004-01-01

    We investigated a method of indirect volume measurement that utilized surface measurements and a simplified formula derived from the formula for a frustum (Sitzia's method) to determine limb volumes in patients with breast cancer-related lymphedema of the upper extremity. Repeated measurements of up

  20. Validity and intra- and interobserver reliability of an indirect volume measurements in patients with upper extremity lymphedema

    NARCIS (Netherlands)

    Meijer, R.S.; Rietman, J.S.; Geertzen, J.H.B.; Bosmans, J.C.; Dijkstra, P.U.

    We investigated a method of indirect volume measurement that utilized surface measurements and a simplified formula derived from the formula for a frustum (Sitzia's method) to determine limb volumes in patients with breast cancer-related lymphedema of the upper extremity. Repeated measurements of

  1. A new method of measuring radio source parameters of a partially polarized distributed source from spacecraft observations

    Science.gov (United States)

    Manning, R.; Fainberg, J.

    1980-01-01

    An experimental system is analyzed which is designed to determine the angular and polarization properties of low frequency radio sources from measurements made on a spinning spacecraft. The system has been optimized to provide high accuracies for sources at high as well as low elevation angles. Theoretical expressions are derived for the response of this system to a partially polarized point source. Integrations are then carried out to get the system response to a uniform circular distributed source. Data processing techniques are derived so that computer simulations can be carried out to investigate the accuracy of this technique. It is shown that using 24 measurements of a partially polarized source (with Q = U = V = 0.5), taken in one spacecraft rotation, the resulting rms errors in angular position are less than one degree and the errors in determining the Stokes parameters are generally 1-10% for a wide range of source elevations.

  2. Repeatability of Volume and Regional Body Composition Measurements of the Lower Limb Using Dual-energy X-ray Absorptiometry

    DEFF Research Database (Denmark)

    Gjorup, Caroline A; Zerahn, Bo; Juul, Sarah

    2016-01-01

    Lower limb lymphedema is a dynamic condition in which tissue composition and volume measurements are affected. Various definitions of lower limb lymphedema exist but volume differences between the limbs are widely used. It is therefore necessary to have a readily available noninvasive measurement...... of agreement on the Bland-Altman plots. These results confirm DXA to be a highly repeatable method for volume and tissue composition measurements of the lower limb. In a population at risk of lymphedema, DXA offers a clinically readily available noninvasive method allowing multiple measurements of volume...... and tissue composition on a routine basis, important for diagnosing, monitoring, managing, and researching lymphedema....

  3. Left Atrial Volume and Pulmonary Artery Diameter Are Noninvasive Measures of Age-Related Diastolic Dysfunction in Mice.

    Science.gov (United States)

    Medrano, Guillermo; Hermosillo-Rodriguez, Jesus; Pham, Thuy; Granillo, Alejandro; Hartley, Craig J; Reddy, Anilkumar; Osuna, Patricia Mejia; Entman, Mark L; Taffet, George E

    2016-09-01

    Impaired cardiac diastolic function occurs with aging in many species and may be difficult to measure noninvasively. In humans, left atrial (LA) volume is a robust measure of chronic diastolic function as the LA is exposed to increased left ventricular filling pressures. We hypothesized that LA volume would be a useful indicator of diastolic function in aging mice. Further, we asked whether pressures were propagated backwards affecting pulmonary arteries (PAs) and right ventricle (RV). We measured LA, PA, and RV infundibulum dimensions with echocardiography and used mouse-specific Doppler systems and pressure catheters for noninvasive and invasive measures. As C57BL/6 mice aged from 3 to 29-31 months, LA volume almost tripled. LA volume increases correlated with traditional diastolic function measures. Within groups of 14- and 31-month-old mice, LA volume correlated with diastolic function measured invasively. In serial studies, mice evaluated at 20 and 24 months showed monotonic increases in LA volume; other parameters changed less predictably. PA diameters, larger in 30-month-old mice than 6-month-old mice, correlated with LA volumes. Noninvasive LA volume and PA diameter assessments are useful and state independent measures of diastolic function in mice, correlating with other measures of diastolic dysfunction in aging. Furthermore, serial measurements over 4 months demonstrated consistent increases in LA volume suitable for longitudinal cardiac aging studies.

  4. Ionization-cluster distributions of alpha-particles in nanometric volumes of propane: measurement and calculation.

    Science.gov (United States)

    De Nardo, L; Colautti, P; Conte, V; Baek, W Y; Grosswendt, B; Tornielli, G

    2002-12-01

    The probability of the formation of ionization clusters by primary alpha-particles at 5.4 MeV in nanometric volumes of propane was studied experimentally and by Monte Carlo simulation, as a function of the distance between the center line of the particle beam and the center of the target volume. The volumes were of cylindrical shape, 3.7 mm in diameter and height. As the investigations were performed at gas pressures of 300 Pa and 350 Pa, the dimensions of the target volume were equivalent to 20.6 nm or 24.0 nm in a material of density 1.0 g/cm(3). The dependence of ionization-cluster formation on distance was studied up to values equivalent to about 70 nm. To validate the measurements, a Monte Carlo model was developed which allows the experimental arrangement and the interactions of alpha-particles and secondary electrons in the counter gas to be properly simulated. This model is supplemented by a mathematical formulation of cluster size formation in nanometric targets. The main results of our study are (i) that the mean ionization-cluster size in the delta-electron cloud of an alpha-particle track segment, decreases as a function of the distance between the center line of the alpha-particle beam and the center of the sensitive target volume to the power of 2.6, and (ii) that the mean cluster size in critical volumes and the relative variance of mean cluster size due to delta-electrons are invariant at distances greater than about 20 nm. We could imagine that the ionization-cluster formation in nanometric volumes might in future provide the physical basis for a redefinition of radiation quality.

  5. Influence of the turbinate volumes as measured by magnetic resonance imaging on nasal air conditioning.

    Science.gov (United States)

    Lindemann, Joerg; Tsakiropoulou, Evangelia; Vital, Victor; Keck, Tilman; Leiacker, Richard; Pauls, Sandra; Wacke, Florian; Wiesmiller, Kerstin M

    2009-01-01

    Changes in nasal airflow caused by varying intranasal volumes and cross-sectional areas affect the contact between air and surrounding mucosa entailing alterations in nasal air conditioning. This study evaluates the correlation between nasal air conditioning and the volumes of the inferior and middle turbinates as measured by magnetic resonance imaging (MRI). Fourteen healthy volunteers were enrolled. Each volunteer had been examined by rhinomanometry, acoustic rhinometry, intranasal air temperature, and humidity measurements at defined intranasal sites as well as MRI of the nasal cavity and the paranasal sinuses. The volumetric data of the turbinates was based on the volumetric software Amira. Comparable results were obtained regarding absolute humidity values and temperature values within the nasal valve area and middle turbinate area for both the right and the left side of the nasal cavity. No statistically significant differences were found in the rhinomanometric values and the acoustic rhinometry results of both sides (p > 0.05). No statistical correlations were found between the volumes of the inferior (mean, 6.1 cm3) and middle turbinate (mean, 1.8 cm3) and the corresponding humidity and temperature values. Additionally, the air temperature and humidity values did not correlate with the rhinometrical endonasal volumes (0-20 mm and 20-50 mm from the nasal entrance). The normal range of volumes of the inferior and middle turbinate does not seem to have a significant impact on intranasal air conditioning in healthy subjects. The exact limits where alterations of the turbinate volume negatively affect nasal air conditioning are still unknown.

  6. Three-dimensional direct measurement of cardiomyocyte volume, nuclearity, and ploidy in thick histological sections.

    Science.gov (United States)

    Bensley, Jonathan Guy; De Matteo, Robert; Harding, Richard; Black, Mary Jane

    2016-01-01

    Quantitative assessment of myocardial development and disease requires accurate measurement of cardiomyocyte volume, nuclearity (nuclei per cell), and ploidy (genome copies per cell). Current methods require enzymatically isolating cells, which excludes the use of archived tissue, or serial sectioning. We describe a method of analysis that permits the direct simultaneous measurement of cardiomyocyte volume, nuclearity, and ploidy in thick histological sections. To demonstrate the utility of our technique, heart tissue was obtained from four species (rat, mouse, rabbit, sheep) at up to three life stages: prenatal, weaning and adulthood. Thick (40 μm) paraffin sections were stained with Wheat Germ Agglutinin-Alexa Fluor 488 to visualise cell membranes, and DAPI (4',6-diamidino-2-phenylindole) to visualise nuclei and measure ploidy. Previous methods have been restricted to thin sections (2-10 μm) and offer an incomplete picture of cardiomyocytes. Using confocal microscopy and three-dimensional image analysis software (Imaris Version 8.2, Bitplane AG, Switzerland), cardiomyocyte volume, nuclearity, and ploidy were measured. This method of staining and analysis of cardiomyocytes enables accurate morphometric measurements in thick histological sections, thus unlocking the potential of archived tissue. Our novel time-efficient method permits the entire cardiomyocyte to be visualised directly in 3D, eliminating the need for precise alignment of serial sections.

  7. Three-dimensional direct measurement of cardiomyocyte volume, nuclearity, and ploidy in thick histological sections

    Science.gov (United States)

    Bensley, Jonathan Guy; de Matteo, Robert; Harding, Richard; Black, Mary Jane

    2016-04-01

    Quantitative assessment of myocardial development and disease requires accurate measurement of cardiomyocyte volume, nuclearity (nuclei per cell), and ploidy (genome copies per cell). Current methods require enzymatically isolating cells, which excludes the use of archived tissue, or serial sectioning. We describe a method of analysis that permits the direct simultaneous measurement of cardiomyocyte volume, nuclearity, and ploidy in thick histological sections. To demonstrate the utility of our technique, heart tissue was obtained from four species (rat, mouse, rabbit, sheep) at up to three life stages: prenatal, weaning and adulthood. Thick (40 μm) paraffin sections were stained with Wheat Germ Agglutinin-Alexa Fluor 488 to visualise cell membranes, and DAPI (4‧,6-diamidino-2-phenylindole) to visualise nuclei and measure ploidy. Previous methods have been restricted to thin sections (2–10 μm) and offer an incomplete picture of cardiomyocytes. Using confocal microscopy and three-dimensional image analysis software (Imaris Version 8.2, Bitplane AG, Switzerland), cardiomyocyte volume, nuclearity, and ploidy were measured. This method of staining and analysis of cardiomyocytes enables accurate morphometric measurements in thick histological sections, thus unlocking the potential of archived tissue. Our novel time-efficient method permits the entire cardiomyocyte to be visualised directly in 3D, eliminating the need for precise alignment of serial sections.

  8. Quantitative measurement of regional lung gas volume by synchrotron radiation computed tomography

    Energy Technology Data Exchange (ETDEWEB)

    Monfraix, Sylvie [European Synchrotron Radiation Facility, BP 220, F-38043 Grenoble (France); Bayat, Sam [European Synchrotron Radiation Facility, BP 220, F-38043 Grenoble (France); Porra, Liisa [Department of Physical Sciences, University of Helsinki, POB 64, FIN-00014 Helsinki (Finland); Berruyer, Gilles [European Synchrotron Radiation Facility, BP 220, F-38043 Grenoble (France); Nemoz, Christian [European Synchrotron Radiation Facility, BP 220, F-38043 Grenoble (France); Thomlinson, William [Canadian Light Source, 101 Perimeter Road, Saskatoon, SK S7N 0X4 (Canada); Suortti, Pekka [Department of Physical Sciences, University of Helsinki, POB 64, FIN-00014 Helsinki (Finland); Sovijaervi, Anssi R A [Department of Clinical Physiology and Nuclear Medicine, Helsinki University Central Hospital, POB 340, FIN-00029 HUS, Helsinki (Finland)

    2005-01-07

    The aim of this study was to assess the feasibility of a novel respiration-gated spiral synchrotron radiation computed tomography (SRCT) technique for direct quantification of absolute regional lung volumes, using stable xenon (Xe) gas as an inhaled indicator. Spiral SRCT with K-edge subtraction using two monochromatic x-ray beams was used to visualize and directly quantify inhaled Xe concentrations and airspace volumes in three-dimensional (3D) reconstructed lung images. Volume measurements were validated using a hollow Xe-filled phantom. Spiral images spanning 49 mm in lung height were acquired following 60 breaths of an 80% Xe-20% O{sub 2} gas mixture, in two anaesthetized and mechanically ventilated rabbits at baseline and after histamine aerosol inhalation. Volumetric images of 20 mm lung sections were obtained at functional residual capacity (FRC) and at end-inspiration. 3D images showed large patchy filling defects in peripheral airways and alveoli following histamine provocation. Local specific lung compliance was calculated based on FRC/end-inspiration images in normal lung. This study demonstrates spiral SRCT as a new technique for direct determination of regional lung volume, offering possibilities for non-invasive investigation of regional lung function and mechanics, with a uniquely high spatial resolution. An example of non-uniform volume distribution in rabbit lung following histamine inhalation is presented.

  9. Measurement and correlation of excess molar volumes for mixtures of 1-propanol and aromatic hydrocarbons

    Energy Technology Data Exchange (ETDEWEB)

    Gahlyan, Suman; Rani, Manju; Maken, Sanjeev Kumar [Deenbandhu Chhotu Ram University of Science and Technology, Murthal (India); Lee, Inkyu; Moon, Il [Yonsei University, Seoul (Korea, Republic of)

    2015-01-15

    Excess molar volumes (V{sub m}{sup E} ) have been measured at 303.15 K for 1-propanol+benzene or toluene or o- or m- or p-xylene mixtures using V-shape dilatometer. The V{sub m}{sup E} values, for an equimolar composition, vary in the order: benzene>toluene-m-xylene>o-xylene>p-xylene. The V{sub m}{sup E} data have been used to calculate partial molar volumes, excess partial molar volumes, and apparent molar volumes of 1-propanol and aromatic hydrocarbons over the entire range of composition. The excess volume data have also been interpreted in terms of graph-theoretical approach and Prigogine-Flory-Patterson theory (PFP). While PFP theory fails to predict the V{sub m}{sup E} values for systems with s-shaped V{sub m}{sup E} versus x{sub 1} graph, the V{sub m}{sup E} values calculated by graph theory compare reasonably well with the corresponding experimental values. This graph theory analysis has further yielded information about the state of aggregation of pure components as well as of the mixtures.

  10. Decreased left temporal lobe volume of panic patients measured by magnetic resonance imaging

    Energy Technology Data Exchange (ETDEWEB)

    Uchida, R.R.; Del-Ben, C.M.; Araujo, D.; Crippa, J.A.; Graeff, F.G. [Sao Paulo Univ., Ribeirao Preto, SP (Brazil). Dept. de Neurologia e Psicologia Medica]. E-mail: fgraeff@keynet.com.br; Santos, A.C. [Sao Paulo Univ., Ribeirao Preto, SP (Brazil). Dept. de Clinica Medica; Guimaraes, F.S. [Sao Paulo Univ., Ribeirao Preto, SP (Brazil). Dept. de Farmacologia

    2003-07-01

    Reported neuroimaging studies have shown functional and morphological changes of temporal lobe structures in panic patients, but only one used a volumetric method. The aim of the present study was to determine the volume of temporal lobe structures in patients with panic disorder, measured by magnetic resonance imaging. Eleven panic patients and eleven controls matched for age, sex, handedness, socioeconomic status and years of education participated in the study. The mean volume of the left temporal lobe of panic patients was 9% smaller than that of controls (t{sub 21} = 2.37, P = 0.028). In addition, there was a trend (P values between 0.05 and 0.10) to smaller volumes of the right temporal lobe (7%, t{sub 21} = 1.99, P = 0.06), right amygdala (8%, t{sub 21} = 1.83, P = 0.08), left amygdala (5%, t{sub 21} = 1.78, P 0.09) and left hippocampus (9%, t{sub 21} = 1.93, P = 0.07) in panic patients compared to controls. There was a positive correlation between left hippocampal volume and duration of panic disorder (r = 0.67, P = 0.025), with recent cases showing more reduction than older cases. The present results show that panic patients have a decreased volume of the left temporal lobe and indicate the presence of volumetric abnormalities of temporal lobe structures. (author)

  11. Human cerebral blood volume measurements using dynamic contrast enhancement in comparison to dynamic susceptibility contrast MRI

    Energy Technology Data Exchange (ETDEWEB)

    Artzi, Moran [Tel Aviv Sourasky Medical Center, Functional Brain Center, The Wohl Institute for Advanced Imaging, Tel Aviv (Israel); Tel Aviv University, Sackler Faculty of Medicine, Tel Aviv (Israel); Liberman, Gilad; Vitinshtein, Faina; Aizenstein, Orna [Tel Aviv Sourasky Medical Center, Functional Brain Center, The Wohl Institute for Advanced Imaging, Tel Aviv (Israel); Nadav, Guy [Tel Aviv Sourasky Medical Center, Functional Brain Center, The Wohl Institute for Advanced Imaging, Tel Aviv (Israel); Tel Aviv University, Faculty of Engineering, Tel Aviv (Israel); Blumenthal, Deborah T.; Bokstein, Felix [Tel Aviv Sourasky Medical Center, Neuro-Oncology Service, Tel Aviv (Israel); Bashat, Dafna Ben [Tel Aviv Sourasky Medical Center, Functional Brain Center, The Wohl Institute for Advanced Imaging, Tel Aviv (Israel); Tel Aviv University, Sackler Faculty of Medicine and Sagol School of Neuroscience, Tel Aviv (Israel)

    2015-07-15

    Cerebral blood volume (CBV) is an important parameter for the assessment of brain tumors, usually obtained using dynamic susceptibility contrast (DSC) MRI. However, this method often suffers from low spatial resolution and high sensitivity to susceptibility artifacts and usually does not take into account the effect of tissue permeability. The plasma volume (v{sub p}) can also be extracted from dynamic contrast enhancement (DCE) MRI. The aim of this study was to investigate whether DCE can be used for the measurement of cerebral blood volume in place of DSC for the assessment of patients with brain tumors. Twenty-eight subjects (17 healthy subjects and 11 patients with glioblastoma) were scanned using DCE and DSC. v{sub p} and CBV values were measured and compared in different brain components in healthy subjects and in the tumor area in patients. Significant high correlations were detected between v{sub p} and CBV in healthy subjects in the different brain components; white matter, gray matter, and arteries, correlating with the known increased tissue vascularity, and within the tumor area in patients. This work proposes the use of DCE as an alternative method to DSC for the assessment of blood volume, given the advantages of its higher spatial resolution, its lower sensitivity to susceptibility artifacts, and its ability to provide additional information regarding tissue permeability. (orig.)

  12. The New York Head-A precise standardized volume conductor model for EEG source localization and tES targeting.

    Science.gov (United States)

    Huang, Yu; Parra, Lucas C; Haufe, Stefan

    2016-10-15

    In source localization of electroencephalograpic (EEG) signals, as well as in targeted transcranial electric current stimulation (tES), a volume conductor model is required to describe the flow of electric currents in the head. Boundary element models (BEM) can be readily computed to represent major tissue compartments, but cannot encode detailed anatomical information within compartments. Finite element models (FEM) can capture more tissue types and intricate anatomical structures, but with the higher precision also comes the need for semi-automated segmentation, and a higher computational cost. In either case, adjusting to the individual human anatomy requires costly magnetic resonance imaging (MRI), and thus head modeling is often based on the anatomy of an 'arbitrary' individual (e.g. Colin27). Additionally, existing reference models for the human head often do not include the cerebro-spinal fluid (CSF), and their field of view excludes portions of the head and neck-two factors that demonstrably affect current-flow patterns. Here we present a highly detailed FEM, which we call ICBM-NY, or "New York Head". It is based on the ICBM152 anatomical template (a non-linear average of the MRI of 152 adult human brains) defined in MNI coordinates, for which we extended the field of view to the neck and performed a detailed segmentation of six tissue types (scalp, skull, CSF, gray matter, white matter, air cavities) at 0.5mm(3) resolution. The model was solved for 231 electrode locations. To evaluate its performance, additional FEMs and BEMs were constructed for four individual subjects. Each of the four individual FEMs (regarded as the 'ground truth') is compared to its BEM counterpart, the ICBM-NY, a BEM of the ICBM anatomy, an 'individualized' BEM of the ICBM anatomy warped to the individual head surface, and FEMs of the other individuals. Performance is measured in terms of EEG source localization and tES targeting errors. Results show that the ICBM-NY outperforms

  13. Relationship between testicular volume and testicular function: comparison of the Prader orchidometric and ultrasonographic measurements in patients with infertility

    Institute of Scientific and Technical Information of China (English)

    Hideo Sakamoto; Yoshio Ogawa; Hideki Yoshida

    2008-01-01

    Aim: To evaluate the relationship between testicular function and testicular volume measured by using Prader orchidometry and ultrasonography (US) to determine the critical testicular volume indicating normal testicular func-tion by each method. Methods: Total testicular volume (right plus left testicular volume) was measured in 794 testes in 397 men with infertility (mean age, 35.6 years) using a Prader orchidometer and also by ultrasonography.Ultrasonographic testicular volumes were calculated as length×width×height×0.71. To evaluate volume-function relationships, patients were divided into 10 groups representing 5-mL increments of total testicular volume by each method from below 10 mL to 50 mL or more. Results: Mean total testicular volume based on Prader orchidometry and US were 36.8 mL and 26.3 mL, respectively. Semen volume, sperm density, total sperm count, total motile sperm count, and serum FSH, LH, and testosterone all correlated significantly with total testicular volume measured by either method. Mean sperm density was in the oligozoospermic range in patients with total testicular volume below 35 mL by orchidometry or below 20 mL by ultrasonography. Mean total sperm count was subnormal in patients with total testicular volume below 30 mL by orchidometry or under 20 mL by ultrasonography. Conclusion: Testicular volume measured by either ultrasonography or Prader orchidometry correlated significantly with testicular function.However, critical total testicular volume indicating normal or nearly normal testicular function was 30 mL to 35 mL using Prader orchidometer and 20 mL using ultrasonography. Prader orchidometry morphometrically and function-ally overestimated the testicular volume in comparison to US.

  14. Fetal lung volume measurement by MRI with high-speed imaging systems

    Energy Technology Data Exchange (ETDEWEB)

    Osada, Hisao; Kaku, Kenshi [Chiba Univ. (Japan). Hospital

    2002-08-01

    Although ultrasonography is widely used for fetal morphologic observation, magnetic resonance imaging (MRI) has gained popularity as a new prenatal diagnostic method with recent introduction of high-speed imaging systems. Infants with lung hypoplasia affecting respiratory function require intensive management starting immediately after birth. Therefore, accurate prenatal differential diagnosis and severity evaluation are extremely important for these fetuses. The aim of this study is to measure fetal lung volume using a computer-based, three-dimensional MRI imaging system and to evaluate the possibility of clinical applications of this procedure. A total of 96 fetuses were evaluated, all were morphologically abnormal, and MRI was done for advanced assessment from 24 to 39 weeks gestation. Three-directional views of fetal chest were imaged by Signa Horizon, 1.5 Tesla, version 5.6 (General Electronics) with the following conditions; coil: TORSO coil, sequence: SSFSE (single shot fast spin echo), slice thickness: 5 mm, and imaging speed: 2 seconds/slice. To calculate the lung volume and create three-dimensional image, the lung area in each slice was traced out, then multiplied using computer image processing. Simultaneously, the volumes of all slices were summed to give the volume of each lung. Linear regression analysis and analysis of covariance (ANCOVA) were used for statistical analyses. In all cases, clear images were obtained, and were adequate for three-dimensional evaluation of the fetal lung. Thirty-five fetuses had poor outcomes, such as intrauterine fetal death, neonatal death, and intensive respiratory care. Regression lines of lung volume versus gestational week were calculated for these fetuses with poor outcome and 61 other fetuses with good outcome. ANCOVA, with gestational week as a covariant, revealed a significant intergroup difference in the lung volume (p<0.001). Similarly, regression lines of lung volume versus fetal body weight estimated by

  15. Portal blood flow volume measurement in schistosomal patients: evaluation of Doppler ultrasonography reproducibility

    Energy Technology Data Exchange (ETDEWEB)

    Leao, Alberto Ribeiro de Souza; Santos, Jose Eduardo Mourao; Moulin, Danilo Sales; Shigueoka, David Carlos; D' Ippolito, Giuseppe [Universidade Federal de Sao Paulo (UNIFESP/EPM), SP (Brazil). Escola Paulista de Medicina. Dept. de Diagnostico por Imagem]. E-mail: ar.leao@uol.com.br; Colleoni, Ramiro [Universidade Federal de Sao Paulo (UNIFESP/EPM), SP (Brazil). Escola Paulista de Medicina. Dept. de Gastroenterologia

    2008-09-15

    Objective: To evaluate the reproducibility of Doppler ultrasonography in the measurement of portal blood flow volume in schistosomal patients. Materials and methods: Prospective, transversal, observational and self-paired study evaluating 21 patients with hepatosplenic schistosomiasis submitted to Doppler ultrasonography performed by three independent observers for measurement of portal blood flow. Pairwise interobserver agreement was calculated by means of the intraclass correlation coefficient, paired t-test and Pearson's correlation coefficient. Results: Interobserver agreement was excellent. Intraclass correlation ranged from 80.6% to 93.0% (IC at 95% [65.3% ; 95.8%]), with the Pearson's correlation coefficient ranging between 81.6% and 92.7% with no statistically significant interobserver difference regarding the mean portal blood flow volume measured by Doppler ultrasonography (p = 0.954 / 0.758 / 0.749). Conclusion: Doppler ultrasonography has demonstrated to be a reliable method for measuring the portal blood flow volume in patients with portal hypertension secondary to schistosomiasis, with a good interobserver agreement. (author)

  16. Volume Measurement Algorithm for Food Product with Irregular Shape using Computer Vision based on Monte Carlo Method

    Directory of Open Access Journals (Sweden)

    Joko Siswantoro

    2014-11-01

    Full Text Available Volume is one of important issues in the production and processing of food product. Traditionally, volume measurement can be performed using water displacement method based on Archimedes’ principle. Water displacement method is inaccurate and considered as destructive method. Computer vision offers an accurate and nondestructive method in measuring volume of food product. This paper proposes algorithm for volume measurement of irregular shape food product using computer vision based on Monte Carlo method. Five images of object were acquired from five different views and then processed to obtain the silhouettes of object. From the silhouettes of object, Monte Carlo method was performed to approximate the volume of object. The simulation result shows that the algorithm produced high accuracy and precision for volume measurement.

  17. Light sources for high-volume manufacturing EUV lithography: technology, performance, and power scaling

    Science.gov (United States)

    Fomenkov, Igor; Brandt, David; Ershov, Alex; Schafgans, Alexander; Tao, Yezheng; Vaschenko, Georgiy; Rokitski, Slava; Kats, Michael; Vargas, Michael; Purvis, Michael; Rafac, Rob; La Fontaine, Bruno; De Dea, Silvia; LaForge, Andrew; Stewart, Jayson; Chang, Steven; Graham, Matthew; Riggs, Daniel; Taylor, Ted; Abraham, Mathew; Brown, Daniel

    2017-06-01

    Extreme ultraviolet (EUV) lithography is expected to succeed in 193-nm immersion multi-patterning technology for sub-10-nm critical layer patterning. In order to be successful, EUV lithography has to demonstrate that it can satisfy the industry requirements in the following critical areas: power, dose stability, etendue, spectral content, and lifetime. Currently, development of second-generation laser-produced plasma (LPP) light sources for the ASML's NXE:3300B EUV scanner is complete, and first units are installed and operational at chipmaker customers. We describe different aspects and performance characteristics of the sources, dose stability results, power scaling, and availability data for EUV sources and also report new development results.

  18. Gas Injection And Fast Pressure-Rise Measurements For The Linac4 H− Source

    CERN Document Server

    Mahner, E; Lettry, J; Mattei, S; O'Neil, M; Neupert, H; Pasquino, C; Schmitzer, C

    2013-01-01

    In the era of the Large Hadron Collider, the CERN injector complex comprising the 34 years old Linac2 with its primary proton source, is presently upgraded with a new linear accelerator for H− (Linac4). The design, construction, and test of volume production and cesiated RF-driven H− ion sources is presently ongoing with the final goal of producing an H− beam with 80 mA beam current, 45 keV beam energy, 500 s pulse length, and a repetition rate of 2 Hz. In order to have quantitative information of the hydrogen gas density at the moment of plasma ignition the dynamic vacuum properties of the plasma generator were studied experimentally. We describe the experimental setup and present fast pressure-rise measurements for different parameters of the gas injection system, such as gas species (H2, He, N2, Ar), piezo valve voltage pulse length (200 - 500 s), and injection pressure (400 - 2800 mbar). The obtained data are compared with a conductance model of the plasma generator.

  19. Fluid Vessel Quantity Using Non-invasive PZT Technology Flight Volume Measurements Under Zero G Analysis

    Science.gov (United States)

    Garofalo, Anthony A

    2013-01-01

    The purpose of the project is to perform analysis of data using the Systems Engineering Educational Discovery (SEED) program data from 2011 and 2012 Fluid Vessel Quantity using Non-Invasive PZT Technology flight volume measurements under Zero G conditions (parabolic Plane flight data). Also experimental planning and lab work for future sub-orbital experiments to use the NASA PZT technology for fluid volume measurement. Along with conducting data analysis of flight data, I also did a variety of other tasks. I provided the lab with detailed technical drawings, experimented with 3d printers, made changes to the liquid nitrogen skid schematics, and learned how to weld. I also programmed microcontrollers to interact with various sensors and helped with other things going on around the lab.

  20. Automated digital volume measurement of melanoma metastases in sentinel nodes predicts disease recurrence and survival

    DEFF Research Database (Denmark)

    Riber-Hansen, Rikke; Nyengaard, Jens R; Hamilton-Dutoit, Stephen J

    2011-01-01

    aim was to investigate whether digital image analysis can estimate TMV accurately in melanoma SLNs. Methods and results: TMV was measured in 147 SLNs from 95 patients both manually and by automated digital image analysis. The results were compared by Bland-Altman plots (numerical data) and kappa......Aims: Total metastatic volume (TMV) is an important prognostic factor in melanoma sentinel lymph nodes (SLNs) that avoids both the interobserver variation and unidirectional upstaging seen when using semi-quantitative size estimates. However, it is somewhat laborious for routine application. Our...... statistics (categorical data). In addition, disease-free and melanoma-specific survivals were calculated. Mean metastatic volume per patient was 10.6 mm(3) (median 0.05 mm(3); range 0.0001-621.3 mm(3)) and 9.62 mm(3) (median 0.05 mm(3); range 0.00001-564.3 mm(3)) with manual and digital measurement...

  1. Fluid Vessel Quantity using Non-Invasive PZT Technology Flight Volume Measurements Under Zero G Analysis

    Science.gov (United States)

    Garofalo, Anthony A.

    2013-01-01

    The purpose of the project is to perform analysis of data using the Systems Engineering Educational Discovery (SEED) program data from 2011 and 2012 Fluid Vessel Quantity using Non-Invasive PZT Technology flight volume measurements under Zero G conditions (parabolic Plane flight data). Also experimental planning and lab work for future sub-orbital experiments to use the NASA PZT technology for fluid volume measurement. Along with conducting data analysis of flight data, I also did a variety of other tasks. I provided the lab with detailed technical drawings, experimented with 3d printers, made changes to the liquid nitrogen skid schematics, and learned how to weld. I also programmed microcontrollers to interact with various sensors and helped with other things going on around the lab.

  2. Dynamic measures of regional lung air volume using phase contrast x-ray imaging

    Energy Technology Data Exchange (ETDEWEB)

    Kitchen, M J; Lewis, R A; Morgan, M J; Siu, K K W; Habib, A [School of Physics, Monash University, Melbourne VIC 3800 (Australia); Wallace, M J; Siew, M L; Hooper, S B [Department of Physiology, Monash University, Melbourne VIC 3800 (Australia); Fouras, A [Division of Biological Engineering, Monash University, Melbourne VIC 3800 (Australia); Yagi, N; Uesugi, K [SPring-8/JASRI, Sayo, Hyogo 679-5198 (Japan)], E-mail: Marcus.Kitchen@sci.monash.edu.au

    2008-11-07

    Phase contrast x-ray imaging can provide detailed images of lung morphology with sufficient spatial resolution to observe the terminal airways (alveoli). We demonstrate that quantitative functional and anatomical imaging of lung ventilation can be achieved in vivo using two-dimensional phase contrast x-ray images with high contrast and spatial resolution (<100 {mu}m) in near real time. Changes in lung air volume as small as 25 {mu}L were calculated from the images of term and preterm rabbit pup lungs (n = 28) using a single-image phase retrieval algorithm. Comparisons with plethysmography and computed tomography showed that the technique provided an accurate and robust method of measuring total lung air volumes. Furthermore, regional ventilation was measured by partitioning the phase contrast images, which revealed differences in aeration for different ventilation strategies.

  3. Metabolic tumour volumes measured at staging in lymphoma: methodological evaluation on phantom experiments and patients

    Energy Technology Data Exchange (ETDEWEB)

    Meignan, Michel [Hopital Henri Mondor and Paris-Est University, Department of Nuclear Medicine, Creteil (France); Paris-Est University, Service de Medecine Nucleaire, EAC CNRS 7054, Hopital Henri Mondor AP-HP, Creteil (France); Sasanelli, Myriam; Itti, Emmanuel [Hopital Henri Mondor and Paris-Est University, Department of Nuclear Medicine, Creteil (France); Casasnovas, Rene Olivier [CHU Le Bocage, Department of Hematology, Dijon (France); Luminari, Stefano [University of Modena and Reggio Emilia, Department of Diagnostic, Clinic and Public Health Medicine, Modena (Italy); Fioroni, Federica [Santa Maria Nuova Hospital-IRCCS, Department of Medical Physics, Reggio Emilia (Italy); Coriani, Chiara [Santa Maria Nuova Hospital-IRCCS, Department of Radiology, Reggio Emilia (Italy); Masset, Helene [Henri Mondor Hospital, Department of Radiophysics, Creteil (France); Gobbi, Paolo G. [University of Pavia, Department of Internal Medicine and Gastroenterology, Fondazione IRCCS Policlinico San Matteo, Pavia (Italy); Merli, Francesco [Santa Maria Nuova Hospital-IRCCS, Department of Hematology, Reggio Emilia (Italy); Versari, Annibale [Santa Maria Nuova Hospital-IRCCS, Department of Nuclear Medicine, Reggio Emilia (Italy)

    2014-06-15

    The presence of a bulky tumour at staging on CT is an independent prognostic factor in malignant lymphomas. However, its prognostic value is limited in diffuse disease. Total metabolic tumour volume (TMTV) determined on {sup 18}F-FDG PET/CT could give a better evaluation of the total tumour burden and may help patient stratification. Different methods of TMTV measurement established in phantoms simulating lymphoma tumours were investigated and validated in 40 patients with Hodgkin lymphoma and diffuse large B-cell lymphoma. Data were processed by two nuclear medicine physicians in Reggio Emilia and Creteil. Nineteen phantoms filled with {sup 18}F-saline were scanned; these comprised spherical or irregular volumes from 0.5 to 650 cm{sup 3} with tumour-to-background ratios from 1.65 to 40. Volumes were measured with different SUVmax thresholds. In patients, TMTV was measured on PET at staging by two methods: volumes of individual lesions were measured using a fixed 41 % SUVmax threshold (TMTV{sub 41}) and a variable visually adjusted SUVmax threshold (TMTV{sub var}). In phantoms, the 41 % threshold gave the best concordance between measured and actual volumes. Interobserver agreement was almost perfect. In patients, the agreement between the reviewers for TMTV{sub 41} measurement was substantial (ρ {sub c} = 0.986, CI 0.97 - 0.99) and the difference between the means was not significant (212 ± 218 cm{sup 3} for Creteil vs. 206 ± 219 cm{sup 3} for Reggio Emilia, P = 0.65). By contrast the agreement was poor for TMTV{sub var}. There was a significant direct correlation between TMTV{sub 41} and normalized LDH (r = 0.652, CI 0.42 - 0.8, P <0.001). Higher disease stages and bulky tumour were associated with higher TMTV{sub 41}, but high TMTV{sub 41} could be found in patients with stage 1/2 or nonbulky tumour. Measurement of baseline TMTV in lymphoma using a fixed 41% SUVmax threshold is reproducible and correlates with the other parameters for tumour mass evaluation

  4. Validation of a continuous penile blood-flow measurement by pulse-volume-plethysmography.

    Science.gov (United States)

    Lavoisier, P; Barbe, R; Gally, M

    2002-04-01

    Today, in the assessment of cavernous artery blood-flow, the most commonly used technique is Doppler ultrasound velocimetry (continuous, pulsed, color-coded or power), which is often considered as the gold standard. Plethysmographic techniques and radioactive tracers have been widely used for the assessment of global penis flow variations but are not adequate for continuous blood-flow measurement. A new pulse-volume plethysmographic (PVP) device using a water-filled penile cuff was employed to assess continuous blood-flow measurement in the penis. Simultaneously Doppler velocity was recorded and served as a gold standard. A penile water-cuff is connected through a pressure tube to a three-way tap. The pulse-volume changes in the penile water-cuff are measured by means of a latex membrane placed over one of the three-way taps. The displacements of the latex are recorded by a photoplethysmograph. The third tap is connected to a 5 l perfusion bag placed 30 cm above the penis so as to maintain constant pressure in the whole device whatever the penis volume. Twenty-four volunteers were tested. The Doppler velocity signal and pulse volume of cavernous arteries were measured simultaneously after PGE1 intra-cavernous injection. Blood-flow variations were induced by increasing penis artery compression with a second penile water-cuff used as a tourniquet fitted onto the penis root, and the pressure of which could be modified by a water-filled syringe. The amplitude of the plethysmographic pulse-volume signal and the area under the Doppler velocity signal were correlated. The inter-patient (n=24) correlation ranged from 0.455 to 0.904, with a mean correlation of 0.704 and P<0.0001. PVP measurement by a water-filled cuff was validated by ultrasound velocimetry. This new continuous, non-invasive and easy-to-use technique enables physiological and physiopathological flow-measurement during sleep, under visual sexual stimulation (VSS), or following artificial erection

  5. International Source Book: Nuclear Fuel Cycle Research and Development Vol 1 Volume 1

    Energy Technology Data Exchange (ETDEWEB)

    Harmon, K. M. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Lakey, L. T. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

    1983-07-01

    This document starts with an overview that summarizes nuclear power policies and waste management activities for nations with significant commercial nuclear fuel cycle activities either under way or planned. A more detailed program summary is then included for each country or international agency conducting nuclear fuel cycle and waste management research and development. This first volume includes the overview and the program summaries of those countries listed alphabetically from Argentina to Italy.

  6. Measurement Combination for Acoustic Source Localization in a Room Environment

    Directory of Open Access Journals (Sweden)

    Pasi Pertilä

    2008-07-01

    Full Text Available The behavior of time delay estimation (TDE is well understood and therefore attractive to apply in acoustic source localization (ASL. A time delay between microphones maps into a hyperbola. Furthermore, the likelihoods for different time delays are mapped into a set of weighted nonoverlapping hyperbolae in the spatial domain. Combining TDE functions from several microphone pairs results in a spatial likelihood function (SLF which is a combination of sets of weighted hyperbolae. Traditionally, the maximum SLF point is considered as the source location but is corrupted by reverberation and noise. Particle filters utilize past source information to improve localization performance in such environments. However, uncertainty exists on how to combine the TDE functions. Results from simulated dialogues in various conditions favor TDE combination using intersection-based methods over union. The real-data dialogue results agree with the simulations, showing a 45% RMSE reduction when choosing the intersection over union of TDE functions.

  7. Measurement Combination for Acoustic Source Localization in a Room Environment

    Directory of Open Access Journals (Sweden)

    Pertilä Pasi

    2008-01-01

    Full Text Available The behavior of time delay estimation (TDE is well understood and therefore attractive to apply in acoustic source localization (ASL. A time delay between microphones maps into a hyperbola. Furthermore, the likelihoods for different time delays are mapped into a set of weighted nonoverlapping hyperbolae in the spatial domain. Combining TDE functions from several microphone pairs results in a spatial likelihood function (SLF which is a combination of sets of weighted hyperbolae. Traditionally, the maximum SLF point is considered as the source location but is corrupted by reverberation and noise. Particle filters utilize past source information to improve localization performance in such environments. However, uncertainty exists on how to combine the TDE functions. Results from simulated dialogues in various conditions favor TDE combination using intersection-based methods over union. The real-data dialogue results agree with the simulations, showing a 45% RMSE reduction when choosing the intersection over union of TDE functions.

  8. Paul Scherrer Institute Scientific Report 1998. Volume VII: Swiss Light Source

    Energy Technology Data Exchange (ETDEWEB)

    Weyer, Heinz Josef; Bugmann, Marlen; Neuhaus, Sibylle [eds.

    1999-09-01

    The Swiss Light Source (SLS) is a medium energy range light source that also provides light with high brilliance in the regime of hard X-rays. It is being constructed at PSI and scheduled to be operational in 2001. A series of new features that were adopted for the design and operation of this machine, is described in this annual report for 1998 figs., tabs., refs.

  9. Know your tools - concordance of different methods for measuring brain volume change after ischemic stroke

    Energy Technology Data Exchange (ETDEWEB)

    Yassi, Nawaf; Campbell, Bruce C.V.; Davis, Stephen M.; Bivard, Andrew [The University of Melbourne, Departments of Medicine and Neurology, Melbourne Brain Centre rate at The Royal Melbourne Hospital, Parkville, Victoria (Australia); Moffat, Bradford A.; Steward, Christopher; Desmond, Patricia M. [The University of Melbourne, Department of Radiology, The Royal Melbourne Hospital, Parkville (Australia); Churilov, Leonid [The University of Melbourne, The Florey Institute of Neurosciences and Mental Health, Parkville (Australia); Parsons, Mark W. [University of Newcastle and Hunter Medical Research Institute, Priority Research Centre for Translational Neuroscience and Mental Health, Newcastle (Australia)

    2015-07-15

    Longitudinal brain volume changes have been investigated in a number of cerebral disorders as a surrogate marker of clinical outcome. In stroke, unique methodological challenges are posed by dynamic structural changes occurring after onset, particularly those relating to the infarct lesion. We aimed to evaluate agreement between different analysis methods for the measurement of post-stroke brain volume change, and to explore technical challenges inherent to these methods. Fifteen patients with anterior circulation stroke underwent magnetic resonance imaging within 1 week of onset and at 1 and 3 months. Whole-brain as well as grey- and white-matter volume were estimated separately using both an intensity-based and a surface watershed-based algorithm. In the case of the intensity-based algorithm, the analysis was also performed with and without exclusion of the infarct lesion. Due to the effects of peri-infarct edema at the baseline scan, longitudinal volume change was measured as percentage change between the 1 and 3-month scans. Intra-class and concordance correlation coefficients were used to assess agreement between the different analysis methods. Reduced major axis regression was used to inspect the nature of bias between measurements. Overall agreement between methods was modest with strong disagreement between some techniques. Measurements were variably impacted by procedures performed to account for infarct lesions. Improvements in volumetric methods and consensus between methodologies employed in different studies are necessary in order to increase the validity of conclusions derived from post-stroke cerebral volumetric studies. Readers should be aware of the potential impact of different methods on study conclusions. (orig.)

  10. On-chip acidification rate measurements from single cardiac cells confined in sub-nanoliter volumes

    OpenAIRE

    Ges, Igor A.; Dzhura, Igor A.; Baudenbacher, Franz J.

    2008-01-01

    The metabolic activity of cells can be monitored by measuring the pH in the extracellular environment. Microfabrication and microfluidic technologies allow the sensor size and the extracellular volumes to be comparable to single cells. A glass substrate with thin film pH sensitive IrOx electrodes was sealed to a replica-molded polydimethylsiloxane (PDMS) microfluidic network with integrated valves. The device, termed NanoPhysiometer, allows the trapping of single cardiac myocytes and the meas...

  11. Measurement of fluid viscosity at microliter volumes using quartz impedance analysis.

    Science.gov (United States)

    Saluja, Atul; Kalonia, Devendra S

    2004-08-05

    The purpose of this work was to measure viscosity of fluids at low microliter volumes by means of quartz crystal impedance analysis. To achieve this, a novel setup was designed that allowed for measurement of viscosity at volumes of 8 to 10 microL. The technique was based on the principle of electromechanical coupling of piezoelectric quartz crystals. The arrangement was simple with measurement times ranging from 2 to 3 minutes. The crystal setup assembly did not impose any unwanted initial stress on the unloaded quartz crystal. Quartz crystals of 5- and 10-MHz fundamental frequency were calibrated with glycerol-water mixtures of known density and viscosity prior to viscosity measurements. True frequency shifts, for the purpose of this work, were determined followed by viscosity measurement of aqueous solutions of sucrose, urea, PEG-400, glucose, and ethylene glycol at 25 degrees C +/- 0.5 degrees C. The measured viscosities were found to be reproducible and consistent with the values reported in the literature. Minor inconsistencies in the measured resistance and frequency shifts did not affect the results significantly, and were found to be experimental in origin rather than due to electrode surface roughness. Besides, as expected for a viscoelastic fluid, PEG 8000 solutions, the calculated viscosities were found to be less than the reported values due to frequency dependence of storage and loss modulus components of complex viscosity. From the results, it can be concluded that the present setup can provide accurate assessment of viscosity of Newtonian fluids and also shows potential for analyzing non-Newtonian fluids at low microliter volumes.

  12. Should ascitis volume and anthropometric measurements be estimated in hospitalized alcoholic cirrotics?

    Directory of Open Access Journals (Sweden)

    E. M. Silva

    2012-12-01

    Full Text Available Introduction: Ascitis and undernutrition are frequent complications of cirrhosis, however ascitis volume and anthropometric assessment are not routinely documented or considered in prognostic evaluation. In a homogeneous cohort followed during two years these variables were scrutinized, aiming to ascertain relevance for longterm outcome. Methods: Population (N = 25, all males with alcoholic cirrhosis was recruited among patients hospitalized for uncomplicated ascitis. Exclusion criteria were refractory or tense ascitis, cancer, spontaneous bacterial peritonitis, bleeding varices and critical illness. Measurements included ultrasonographically estimated ascitis volume, dry body mass index/BMI , upper arm anthropometrics, hematologic counts and liver function tests. Results: Population (age 48.3 ± 11.3 years, BMI 21.1± 3.5 kg/m², serum albumin 2.5 ± 0.8 g/dL was mostly in the Child-Pugh C category (77.8% but clinically stable. During the follow-up period of 22.6 ±3.8 months, additional hospitalizations numbered 1.7 ± 1.0 and more than one quarter succumbed. Admission ascitis volume corresponded to 7.1 ± 3.6 L and dry BMI to 18.3 ± 3.5 kg/m². Child Pugh index was relevant for both mortality and rehospitalization. Nevertheless, similar matches for mortality were documented with ascitis volume and dry BMI, and arm circumference below the 5th percentile was highly significantly associated with rehospitalization. Conclusions: A greater association than hitherto acknowledged, between ascitis volume and anthropometric measurements from one side, and long-term rehospitalization and mortality from the other, was demonstrated in male stable alcoholic cirrhotics. Further studies with alcoholic and other modalities of cirrhosis including women are recommended.

  13. Trabecular-Iris Circumference Volume in Open Angle Eyes Using Swept-Source Fourier Domain Anterior Segment Optical Coherence Tomography

    Directory of Open Access Journals (Sweden)

    Mohammed Rigi

    2014-01-01

    Full Text Available Purpose. To introduce a new anterior segment optical coherence tomography parameter, trabecular-iris circumference volume (TICV, which measures the integrated volume of the peripheral angle, and establish a reference range in normal, open angle eyes. Methods. One eye of each participant with open angles and a normal anterior segment was imaged using 3D mode by the CASIA SS-1000 (Tomey, Nagoya, Japan. Trabecular-iris space area (TISA and TICV at 500 and 750 µm were calculated. Analysis of covariance was performed to examine the effect of age and its interaction with spherical equivalent. Results. The study included 100 participants with a mean age of 50 (±15 years (range 20–79. TICV showed a normal distribution with a mean (±SD value of 4.75 µL (±2.30 for TICV500 and a mean (±SD value of 8.90 µL (±3.88 for TICV750. Overall, TICV showed an age-related reduction (P=0.035. In addition, angle volume increased with increased myopia for all age groups, except for those older than 65 years. Conclusions. This study introduces a new parameter to measure peripheral angle volume, TICV, with age-adjusted normal ranges for open angle eyes. Further investigation is warranted to determine the clinical utility of this new parameter.

  14. Reproducibility of techniques using Archimedes' principle in measuring cancellous bone volume.

    Science.gov (United States)

    Zou, L; Bloebaum, R D; Bachus, K N

    1997-01-01

    Researchers have been interested in developing techniques to accurately and reproducibly measure the volume fraction of cancellous bone. Historically bone researchers have used Archimedes' principle with water to measure the volume fraction of cancellous bone. Preliminary results in our lab suggested that the calibrated water technique did not provide reproducible results. Because of this difficulty, it was decided to compare the conventional water method to a water with surfactant and a helium method using a micropycnometer. The water/surfactant and the helium methods were attempts to improve the fluid penetration into the small voids present in the cancellous bone structure. In order to compare the reproducibility of the new methods with the conventional water method, 16 cancellous bone specimens were obtained from femoral condyles of human and greyhound dog femora. The volume fraction measurements on each specimen were repeated three times with all three techniques. The results showed that the helium displacement method was more than an order of magnitudes more reproducible than the two other water methods (p < 0.05). Statistical analysis also showed that the conventional water method produced the lowest reproducibility (p < 0.05). The data from this study indicate that the helium displacement technique is a very useful, rapid and reproducible tool for quantitatively characterizing anisotropic porous tissue structures such as cancellous bone.

  15. A measurement-based X-ray source model characterization for CT dosimetry computations.

    Science.gov (United States)

    Sommerville, Mitchell; Poirier, Yannick; Tambasco, Mauro

    2015-11-08

    less than 3.50%. Thirty-five out of a total of 36 simulation conditions were within the experimental uncertainties associated with measurement reproducibility and chamber volume effects for the PMMA phantom. The agreement between calculation and measurement was within experimental uncertainty for 19 out of 20 simulation conditions at five points of interest in the anthropomorphic thorax phantom for the four beam energies modeled. The source model and characterization technique based on HVL measurements and nominal kVp can be used to accurately compute CT dose. This accuracy provides experimental validation of kVDoseCalc for computing CT dose.

  16. Higher Education Costs: Concepts, Measurement Issues, Data Sources, and Uses.

    Science.gov (United States)

    Layzell, Daniel T.; Caruthers, J. Kent

    2002-01-01

    Provides a basic overview of the concept of cost in higher education and related issues, discusses major consumers of higher education cost data and their perspectives, outlines the major sources of data on higher education costs, and describes some of the major (and perennial) issues related to higher education costs. (EV)

  17. Precise measurement of liquid petroleum tank volume based on data cloud analysis

    Science.gov (United States)

    Wang, Jintao; Liu, Ziyong; Zhang, Long; Guo, Ligong; Bao, Xuesong; Tong, Lin

    2010-08-01

    Metal tanks are generally used for the measurement of liquid petroleum products for fiscal or custody transfer application. One tank volume precise measurement method based on data cloud analysis was studied, which was acquired by laser scanning principle. Method of distance measurement by laser phase shift and angular measurement by optical grating were applied to acquire coordinates of points in tank shell under the control of a servo system. Direct Iterative Method (DIM) and Section Area Method (SAM) were used to process measured data for vertical and horizontal tanks respectively. In comparison experiment, one 1000m3 vertical tank and one 30m3 horizontal tank were used as test objects. In the vertical tank experiment, the largest measured radius difference between the new laser method and strapping method (international arbitrary standard) is 2.8mm. In the horizontal tank experiment, the calibration result from laser scanning method is more close to reference than manual geometric method, and the mean deviation in full-scale range of the former and latter method are 75L and 141L respectively; with the increase of liquid level, the relative errors of laser scanning method and manual geometric method become smaller, and the mean relative errors are 0.6% and 1.5% respectively. By using the method discussed, the calibration efficiency of tank volume can be improved.

  18. Usefulness and limitation of punched-out orchidometer in testicular volume measurement

    Institute of Scientific and Technical Information of China (English)

    Koji Shiraishi; Hiroshi Takihara; Yoriaki Kamiryo; Katsusuke Naito

    2005-01-01

    Aim: To determine the limitations of a punched-out orchidometer in practical use, we compared with a scrotal ultrasound (USG). Methods: A total of 281 testes from 142 males were examined using both a punched-out orchidometer and a USG. The volume differential between both methods was calculated and expressed as orchidometer/USG volume (O/U ratio). Distribution of the O/U ratio was determined and subdivided by clinical or pathological diagnosis. The correlations between the O/U ratio and patient age or orchidometer results were assessed. Results:There was a significant linear relationship between the results of orchidometer and USG (r = 0.94, P < 0.0001). The relationship between the O/U ratio and age or testicular volumes showed significant inverse correlations (r = 0.22,P = 0.0002, r = 0.45, P<0.0001, respectively). Klinefelter's syndrome, ipsilateral detorted testes and hypogonadotropic hypogonadism comparatively showed a high O/U ratio. No incidental lesion was detected by USG necessitating treatment. Conclusion: The punched-out orchidometer gives estimates that correlated well with the USG measurements and provides enough information for routine andrological evaluation. We should be aware that the orchidometer often overestimates the testicular volume, especially for the patients with small testis or adolescents.

  19. Composite-Light-Source Interferometer for Real-Time Micro-Vibration Measurements

    Institute of Scientific and Technical Information of China (English)

    Dailin Li; Xiangzhao Wang

    2003-01-01

    A novel interferometer using a composite light source for real time measurements of micro-vibrations is proposed.The experimental results make it clear that it is insensitive to external disturbances and intensity fluctuations of the source light.

  20. Composite-Light-Source Interferometer for Real-Time Micro-Vibration Measurements

    Institute of Scientific and Technical Information of China (English)

    2003-01-01

    A novel interferometer using a composite light source for real time measurements of micro-vibrations is proposed. The experimental results make it clear that it is insensitive to external disturbances and intensity fluctuations of the source light.

  1. The analysis of deviations on measured volumes between OSBRA pipeline tank farms and its customers

    Energy Technology Data Exchange (ETDEWEB)

    Kotchetkoff Neto, Andre Paulo; Kawamoto, Fabio Yoshikazu [Petrobas Transporte S.A. - Transpetro, (Brazil)

    2010-07-01

    The Sao Paulo - Brasilia pipeline (OSBRA) is a very long multi product pipeline in Brazil. It has a network of several tank farms, pump stations and truck loadings to deliver oil, gas and LPG to customers. The volume of these fuels is usually measured before delivery at two measure points. This paper reports the use of statistical tools to analyze the measurement data. The purpose was to understand the computed differences between the OSBRA tank farm installations and the customer tank farm installations. The use of statistical tools brought new insights, such as the existence of systematic error or the variability of each individual system. These tools were also used to verify the accuracy of operational measurement devices. An analysis based on in-field data was carried out between two OSBRA tank farms. This paper showed that the use of statistical tools, rather than fixed limits, can provide more precise information about measurement systems behaviors.

  2. CT-measured regional specific volume change reflects regional ventilation in supine sheep.

    Science.gov (United States)

    Fuld, Matthew K; Easley, R Blaine; Saba, Osama I; Chon, Deokiee; Reinhardt, Joseph M; Hoffman, Eric A; Simon, Brett A

    2008-04-01

    Computer tomography (CT) imaging techniques permit the noninvasive measurement of regional lung function. Regional specific volume change (sVol), determined from the change in lung density over a tidal breath, should correlate with regional ventilation and regional lung expansion measured with other techniques. sVol was validated against xenon (Xe)-CT-specific ventilation (sV) in four anesthetized, intubated, mechanically ventilated sheep. Xe-CT used expiratory gated axial scanning during the washin and washout of 55% Xe. sVol was measured from the tidal changes in tissue density (H, houndsfield units) of lung regions using the relationship sVol = [1,000(Hi - He)]/[He(1,000 + Hi)], where He and Hi are expiratory and inspiratory regional density. Distinct anatomical markings were used to define corresponding lung regions of interest between inspiratory, expiratory, and Xe-CT images, with an average region of interest size of 1.6 +/- 0.7 ml. In addition, sVol was compared with regional volume changes measured directly from the positions of implanted metal markers in an additional animal. A linear relationship between sVol and sV was demonstrated over a wide range of regional sV found in the normal supine lung, with an overall correlation coefficient (R(2)) of 0.66. There was a tight correlation (R(2) = 0.97) between marker-measured volume changes and sVol. Regional sVol, which involves significantly reduced exposure to radiation and Xe gas compared with the Xe-CT method, represents a safe and efficient surrogate for measuring regional ventilation in experimental studies and patients.

  3. Capillary method for measuring near-infrared spectra of microlitre volume liquids

    Institute of Scientific and Technical Information of China (English)

    YUAN Bo; MURAYAMA Koichi

    2007-01-01

    The present study theoretically explored the feasibility of the capillary method for measuring near-infrared (NIR) spectra of liquid or solution samples with microlitre volume, which was proposed in our previous studies. Lambert-Beer absorbance rule was applied to establish a model for the integral absorbance of capillary, which was then implemented in numerical analyses of the effects of capillary on various spectral features and dynamic range of absorption measurement. The theoretical speculations indicated that the capillary method might be used in NIR spectroscopy, which was further supported by the empirical data collected from our experiments by comparison between capillary NIR spectra of several organic solvents and cuvette cell NIR spectra.

  4. Noninvasive Intracranial Volume and Pressure Measurements Using Ultrasound (Head and Spinal)

    Science.gov (United States)

    Hargens, Alan R.

    1999-01-01

    Prevention of secondary brain injuries following head trauma can be accomplished most easily when intracranial pressure (ICP) is monitored. However, current measurement techniques are invasive and thus not practical in the combat environment. The Pulsed Phase Lock Loop device, which was developed and patented by consultants Drs. Yost and Cantrell, uses a unique, noninvasive ultrasonic phase comparison method to measure slight changes in cranial volume which occur with changes in ICP. Year two studies included whole body head-up and head-down tilting effects on intracranial compliance and pressure in six healthy volunteers.

  5. On the efficiency of stochastic volume sources for the determination of light meson masses

    CERN Document Server

    Endress, E; Wittig, H

    2011-01-01

    We investigate the efficiency of single timeslice stochastic sources for the calculation of light meson masses on the lattice as one varies the quark mass. Simulations are carried out with Nf = 2 flavours of non-perturbatively O(a) improved Wilson fermions for pion masses in the range of 450 - 760 MeV. Results for pseudoscalar and vector meson two-point correlation functions computed using stochastic as well as point sources are presented and compared. At fixed computational cost the stochastic approach reduces the variance considerably in the pseudoscalar channel for all simulated quark masses. The vector channel is more affected by the intrinsic stochastic noise. In order to obtain stable estimates of the statistical errors and a more pronounced plateau for the effective vector meson mass, a relatively large number of stochastic sources must be used.

  6. A time-of-flight flow sensor for the volume measurement of trace amount of interstitial fluid

    Science.gov (United States)

    Yu, H.; Li, D.; Roberts, R. C.; Xu, K.; Tien, N. C.

    2012-05-01

    Transdermal extraction of interstitial fluid (ISF) offers an attractive method for noninvasive blood glucose monitoring. The existing macroscale systems are not suitable for ISF collection, mainly because of the minute volume of the transdermally extracted ISF which scatters on the skin surface. Human skin's low permeability to glucose and its varying permeability exemplify the crucial need to make precise ISF volume measurements in order to calculate blood glucose concentrations accurately. In this paper, we present a novel time-of-flight flow sensor consisting of four electrode pairs fabricated directly into the channel of a polydimethylsiloxane (PDMS) microfluidic device designed to accurately measure the volume of transdermally extracted ISF. As fluid traverses the channel, it bridges each electrode pair and changes its resistance. By measuring the time difference in resistance change between each electrode pair, a precise fluid volume can be measured. In order to verify the suitability of the sensor for biological applications, experiments were conducted using a normal saline solution which is similar to ISF. The stability of the sensor was tested using a fixed volume, and the coefficient of variation for 20 tests was determined to be 0.0041. The consistency of the sensor for varied volume measurements was shown by the high correlation coefficient (R2 = 0.9992) between the tested volume and the volume measured by a commercial micro syringe. The excellent functionality of the flow sensor can be extended toward the measurement of conductive chemical and biochemical buffers and reagents.

  7. International Source Book: Nuclear Fuel Cycle Research and Development Volume 2

    Energy Technology Data Exchange (ETDEWEB)

    Harmon, K. M.; Lakey, L. T.

    1982-11-01

    This document starts with an overview that summarizes nuclear power policies and waste management activities for nations with significant commercial nuclear fuel cycle activities either under way or planned. A more detailed program summary is then included for each country or international agency conducting nuclear fuel cycle and waste management research and development. This second volume includes the program summaries of those countries listed alphabetically from Japan to Yugoslavia. Information on international agencies and associations, particularly the IAEA, NEA, and CEC, is provided also.

  8. Verification of Conjugate Heat Transfer Models in a Closed Volume with Radiative Heat Source

    Directory of Open Access Journals (Sweden)

    Maksimov Vyacheslav I.

    2016-01-01

    Full Text Available The results of verification of mathematical model of convective-conductive heat transfer in a closed volume with a thermally conductive enclosing structures are presented. Experiments were carried out to determine the temperature of floor premises in the working conditions of radiant heating systems. Comparison of mathematical modelling of temperature fields and experiments showed their good agreement. It is concluded that the mathematical model of conjugate heat transfers in the air cavity with a heat-conducting and heat-retaining walls correspond to the real process of formation of temperature fields in premises with gas infrared heaters system.

  9. Contrast volume reduction using third generation dual source computed tomography for the evaluation of patients prior to transcatheter aortic valve implantation

    Energy Technology Data Exchange (ETDEWEB)

    Bittner, Daniel O. [University Hospital Erlangen, Friedrich-Alexander University Erlangen-Nuernberg (FAU), Department of Internal Medicine 2 (Cardiology), Erlangen (Germany); Harvard Medical School, Cardiac MR PET CT Program, Massachusetts General Hospital, Boston, MA (United States); Arnold, Martin; Klinghammer, Lutz; Schuhbaeck, Annika; Hell, Michaela M.; Muschiol, Gerd; Gauss, Soeren; Achenbach, Stephan; Marwan, Mohamed [University Hospital Erlangen, Friedrich-Alexander University Erlangen-Nuernberg (FAU), Department of Internal Medicine 2 (Cardiology), Erlangen (Germany); Lell, Michael; Uder, Michael [University Hospital Erlangen, Friedrich-Alexander University Erlangen-Nuernberg (FAU), Department of Radiology, Erlangen (Germany); Hoffmann, Udo [Harvard Medical School, Cardiac MR PET CT Program, Massachusetts General Hospital, Boston, MA (United States)

    2016-12-15

    Chronic renal failure is common in patients referred for transcatheter aortic valve implantation (TAVI). CT angiography is recommended and provides crucial information prior to TAVI. We evaluated the feasibility of a reduced contrast volume protocol for pre-procedural CT imaging. Forty consecutive patients were examined with prospectively ECG-triggered high-pitch spiral acquisition using a novel third-generation dual-source CT system; 38 ml contrast agent was used. Image quality was graded on a visual scale (1-4). Contrast attenuation was measured at the level of the aortic root and at the iliac bifurcation. Mean patient age was 82 ± 6 years (23 males; 58 %). Mean attenuation/average image quality was 285 ± 60 HU/1.5 at the aortic annulus compared to 289 ± 74 HU/1.8 at the iliac bifurcation (p = 0.77/p = 0.29). Mean estimated effective radiation dose was 2.9 ± 0.3 mSv. A repeat acquisition was necessary in one patient due to image quality. Out of the 35 patients who underwent TAVI, 31 (89 %) patients had no or mild aortic regurgitation. Thirty-two (91 %) patients were discharged successfully. Pre-procedural CTA with a total of 38 ml contrast volume is feasible and clinically useful, using third-generation dual-source CT, allowing comprehensive imaging for procedural success. (orig.)

  10. The Development of a Flexible Measuring System for Muscle Volume Using Ultrasonography

    Science.gov (United States)

    Fukumoto, Kiyotaka; Fukuda, Osamu; Tsubai, Masayoshi; Muraki, Satoshi

    Quantification of muscle volume can be used as a means for the estimation of muscle strength. Its measuring process does not need the subject's muscular contractions so it is completely safe and particularly suited for elderly people. Therefore, we have developed a flexible measuring system for muscle volume using ultrasonography. In this system, an ultrasound probe is installed on a link mechanism which continuously scans fragmental images along the human body surface. These images are then measured and composed into a wide area cross-sectional image based on the spatial compounding method. The flexibility of the link mechanism enables the operator to measure the images under any body postures and body site. The spatial compounding method significantly reduces speckle and artifact noises from the composed cross-sectional image so that the operator can observe the individual muscles, such as Rectus femoris, Vastus intermedius, and so on, in detail. We conducted the experiments in order to examine the advantages of this system we have developed. The experimental results showed a high accuracy of the measuring position which was calculated using the link mechanism and presented the noise reduction effect based on the spatial compounding method. Finally, we confirmed high correlations between the MRI images and the ones of the developed system to verify the validity of the system.

  11. Technical Note: Influence of Compton currents on profile measurements in small-volume ion chambers

    Energy Technology Data Exchange (ETDEWEB)

    Tanny, Sean; Sperling, Nicholas; Parsai, E. Ishmael, E-mail: e.parsai@utoledo.edu [Department of Radiation Oncology, University of Toledo Medical Center, 1325 Conference Drive, Toledo, Ohio 43614 (United States); Holmes, Shannon [Standard Imaging, 3120 Deming Way, Middleton, Wisconsin 53562 (United States)

    2015-10-15

    Purpose: This work is to evaluate the effects of Compton current generation in three small-volume ionization chambers on measured beam characteristics for electron fields. Methods: Beam scans were performed using Exradin A16, A26, and PTW 31014 microchambers. Scans with varying chamber components shielded were performed. Static point measurements, output factors, and cable only irradiations were performed to determine the contribution of Compton currents to various components of the chamber. Monte Carlo simulations were performed to evaluate why one microchamber showed a significant reduction in Compton current generation. Results: Beam profiles demonstrated significant distortion for two of the three chambers when scanned parallel to the chamber axis, produced by electron deposition within the wire. Measurements of ionization produced within the cable identified Compton current generation as the cause of these distortions. The size of the central collecting wire was found to have the greatest influence on the magnitude of Compton current generation. Conclusions: Microchambers can demonstrate significant (>5%) deviations from properties as measured with larger volume chambers (0.125 cm{sup 3} and above). These deviations can be substantially reduced by averaging measurements conducted at opposite polarities.

  12. Simulation study of a magnetocardiogram based on a virtual heart model: effect of a cardiac equivalent source and a volume conductor

    Institute of Scientific and Technical Information of China (English)

    Shou Guo-Fa; Xia Ling; Ma Ping; Tang Fa-Kuan; Dai Ling

    2011-01-01

    In this paper, we present a magnetocardiogram (MCG) simulation study using the boundary element method (BEM) and based on the virtual heart model and the realistic human volume conductor model. The different contributions of cardiac equivalent source models and volume conductor models to the MCG are deeply and comprehensively investigated. The single dipole source model, the multiple dipoles source model and the equivalent double layer (EDL) source model are analysed and compared with the cardiac equivalent source models. Meanwhile, the effect of the volume conductor model on the MCG combined with these cardiac equivalent sources is investigated. The simulation results demonstrate that the cardiac electrophysiological information will be partly missed when only the single dipole source is taken, while the EDL source is a good option for MCG simulation and the effect of the volume conductor is smallest for the EDL source. Therefore, the EDL source is suitable for the study of MCG forward and inverse problems, and more attention should be paid to it in future MCG studies.

  13. Validation of Respiratory Inductance Plethysmography for Measuring Tidal Volume in Swine.

    Science.gov (United States)

    Su, Zhenbo; Oto, Jun; Wang, Jingwen; Kimball, William R; Chenelle, Christopher T; Kacmarek, Robert M; King, David R; Jiang, Yandong; Duggan, Michael J

    2015-06-01

    Measuring tidal volume (VT) in nonintubated swine or swine with leaking breathing circuits is challenging. The aim of this study was to validate respiratory inductance plethysmography (RIP) for measuring VT in swine that are comparable in size to adult humans. To determine calibration curves, VT and RIP readings were obtained from anesthetized swine (n = 8; weight, 46-50 kg) during positive-pressure (mechanical) ventilation and spontaneous breathing. For positive-pressure ventilation, 6 pigs were mechanically ventilated by using the pressure-control mode. The 2 pigs in the spontaneously breathing cohort each received a single intravenous bolus dose of propofol to abolish spontaneous breathing; VT was measured during gradual return of their respiratory drive. A flow-volume sensor was placed between the proximal end of the endotracheal tube and breathing circuit for the recording of inspiratory and expiratory VT. RIP readings were recorded by using 2 bands, which simultaneously measured ribcage and abdominal excursions. The data revealed that VT was linearly correlated with the movements of both ribcage and abdomen as measured by using plethysmography over a large range of tidal volume (44 to 1065 mL). In addition, the intercept of the linear equation was small or even negative during spontaneous breathing but increased significantly (maximum, 145 mL, 59.2 ± 35.1 mL) during positive pressure ventilation. Our results indicate that VT in swine can be calculated by using a simple univariate linear regression equation with RIP readings obtained during either mechanical ventilation or spontaneous breathing.

  14. Measurement of maxillary sinus volume and available alveolar bone height using computed tomography

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Jae Hak; Han, Won Jeong; Choi, Young Hi; Kim, Eun Kyung [Dankook University College of Medicine, Seoul (Korea, Republic of)

    2003-03-15

    To aid in determining the volume of graft bone required before a maxillary sinus lift procedure and compare the alveolar bone height measurements taken by panoramic radiographs to those by CT images. Data obtained by both panoramic radiographs and CT examination of 25 patients were used in this study. Maxillary sinus volumes from the antral floor to heights of 5 mm, 10 mm, 15 mm, and 20 mm , were calculated. Alveolar bone height was measured on the panoramic images at each maxillary tooth site and corrected by magnification rate (PBH). Available bone height (ABH) and full bone height (FBH) was measured on reconstructed CT images. PBH was compared with ABH and FBH at the maxillary incisors, canines, premolars, and molars. Volumes of the inferior portion of the sinuses were 0.55 {+-} 0.41 cm{sup 3} for 5 mm lifts, 2.11 {+-} 0.68 cm{sup 3} for 10 mm, 4.26 {+-} 1.32 cm{sup 3} for 15 mm, 6.95 {+-} 2.01 cm{sup 3} for 20 mm. For the alveolar bone measurement, measurements by panoramic images were longer than available bone heights determined by CT images at the incisor and canine areas, and shorter than full bone heights on CT images at incisor, premolar, and molar areas (p<0.001). In bone grafting of the maxillary sinus floor, 0,96 cm{sup 3} or more is required for a 5 mm - lift, 2.79 cm{sup 3} or more for a 10 mm - lift, 5.58 cm{sup 3} or more for a 15 mm - lift, and 8.96 cm{sup 3} or more for a 20 mm - lift. Maxillary implant length determined using panoramic radiograph alone could result in underestimation or overestimation, according to the site involved.

  15. Directivity of Spherical Polyhedron Sound Source Used in Near-Field HRTF Measurements

    Institute of Scientific and Technical Information of China (English)

    YU Guang-Zheng; XIE Bo-Sun; RAO Dan

    2010-01-01

    @@ The omnidirectional character is one of important requirements for the sound source used in near-field headrelated transfer function(HRTF)measurements.Based on the analysis on the radiation sound pressure and directivity character of various spherical polyhedron sound sources,a spherical dodecahedral sound source with radius of 0.035 m is proposed and manufactured.Theoretical and measured results indicate that the sound source is approximately omnidirectional below the frequency of 8 kHz.In addition,the sound source has reasonable magnitude response from 350Hz to 20kHz and linear phase characteristics.Therefore.it is suitahle for the near-field HRTF measurements.

  16. Accounting for uncertainty in volumes of seabed change measured with repeat multibeam sonar surveys

    Science.gov (United States)

    Schimel, Alexandre C. G.; Ierodiaconou, Daniel; Hulands, Lachlan; Kennedy, David M.

    2015-12-01

    Seafloors of unconsolidated sediment are highly dynamic features; eroding or accumulating under the action of tides, waves and currents. Assessing which areas of the seafloor experienced change and measuring the corresponding volumes involved provide insights into these important active sedimentation processes. Computing the difference between Digital Elevation Models (DEMs) obtained from repeat Multibeam Echosounders (MBES) surveys has become a common technique to identify these areas, but the uncertainty in these datasets considerably affects the estimation of the volumes displaced. The two main techniques used to take into account uncertainty in volume estimations are the limitation of calculations to areas experiencing a change in depth beyond a chosen threshold, and the computation of volumetric confidence intervals. However, these techniques are still in their infancy and, as a result, are often crude, seldom used or poorly understood. In this article, we explored a number of possible methodological advances to address this issue, including: (1) using the uncertainty information provided by the MBES data processing algorithm CUBE, (2) adapting fluvial geomorphology techniques for volume calculations using spatially variable thresholds and (3) volumetric histograms. The nearshore seabed off Warrnambool harbour - located in the highly energetic southwest Victorian coast, Australia - was used as a test site. Four consecutive MBES surveys were carried out over a four-months period. The difference between consecutive DEMs revealed an area near the beach experiencing large sediment transfers - mostly erosion - and an area of reef experiencing increasing deposition from the advance of a nearby sediment sheet. The volumes of sediment displaced in these two areas were calculated using the techniques described above, both traditionally and using the suggested improvements. We compared the results and discussed the applicability of the new methodological improvements

  17. Intraobserver and interobserver agreement of volume perfusion CT (VPCT) measurements in patients with lung lesions

    Energy Technology Data Exchange (ETDEWEB)

    Sauter, Alexander W., E-mail: alexander.sauter@klinikum.uni-tuebingen.de [Department of Diagnostic and Interventional Radiology, University Hospital of Tuebingen, Hoppe-Seyler-Str. 3, 72076 Tuebingen (Germany); Merkle, Anne, E-mail: anne_merkle@web.de [Department of Diagnostic and Interventional Radiology, University Hospital of Tuebingen, Hoppe-Seyler-Str. 3, 72076 Tuebingen (Germany); Schulze, Maximilian, E-mail: maximilian.schulze@med.uni-tuebingen.de [Department of Diagnostic and Interventional Radiology, University Hospital of Tuebingen, Hoppe-Seyler-Str. 3, 72076 Tuebingen (Germany); Spira, Daniel, E-mail: daniel.spira@med.uni-tuebingen.de [Department of Diagnostic and Interventional Radiology, University Hospital of Tuebingen, Hoppe-Seyler-Str. 3, 72076 Tuebingen (Germany); Hetzel, Juergen, E-mail: juergen.hetzel@med.uni-tuebingen.de [Departments of Oncology, Hematology, Immunology, Rheumatology and Pulmonology, University Hospital of Tuebingen, Otfried-Mueller-Str. 10, 72076 Tuebingen (Germany); Claussen, Claus D., E-mail: claus.claussen@med.uni-tuebingen.de [Department of Diagnostic and Interventional Radiology, University Hospital of Tuebingen, Hoppe-Seyler-Str. 3, 72076 Tuebingen (Germany); Horger, Marius S., E-mail: marius.horger@med.uni-tuebingen.de [Department of Diagnostic and Interventional Radiology, University Hospital of Tuebingen, Hoppe-Seyler-Str. 3, 72076 Tuebingen (Germany)

    2012-10-15

    Objectives: To evaluate intraobserver and interobserver agreement of manually encompassed lung lesions for perfusion measurements using volume-perfusion computed tomography (VPCT). Materials and methods: Institutional review board approval and informed consent were obtained. HIPAA guidelines were followed. A 65-s dynamic study was acquired with scan parameters 80 kV, 60 mA s (80 mA s for patients ≥70 kg), 128 × 0.6 mm collimation. Blood flow (BF), blood volume (BV) and K{sup trans} parameters were determined by syngo volume perfusion CT body with 88 lesions analyzed retrospectively. Results: Within-subject coefficients of variation for intraobserver agreement (range 6.59–12.82%) were superior to those for interobserver agreement (range 21.75–38.30%). Size-dependent analysis revealed lower agreements for lesions <4 cm as compared to larger lesions. Additionally, agreements of the upper, middle and lower lung zones were different. Conclusions: Intraobserver agreement was substantial for VPCT lung cancer perfusion measurements encouraging the use for tumor characterization and therapy response monitoring. Interobserver agreement is limited and unexperienced readers should be trained before using this new method.

  18. Determination of volume fractions in two-phase flows from sound speed measurement

    Energy Technology Data Exchange (ETDEWEB)

    Chaudhuri, Anirban [Los Alamos National Laboratory; Sinha, Dipen N. [Los Alamos National Laboratory; Osterhoudt, Curtis F. [University of Alaska

    2012-08-15

    Accurate measurement of the composition of oil-water emulsions within the process environment is a challenging problem in the oil industry. Ultrasonic techniques are promising because they are non-invasive and can penetrate optically opaque mixtures. This paper presents a method of determining the volume fractions of two immiscible fluids in a homogenized two-phase flow by measuring the speed of sound through the composite fluid along with the instantaneous temperature. Two separate algorithms are developed by representing the composite density as (i) a linear combination of the two densities, and (ii) a non-linear fractional formulation. Both methods lead to a quadratic equation with temperature dependent coefficients, the root of which yields the volume fraction. The densities and sound speeds are calibrated at various temperatures for each fluid component, and the fitted polynomial is used in the final algorithm. We present results when the new algorithm is applied to mixtures of crude oil and process water from two different oil fields, and a comparison of our results with a Coriolis meter; the difference between mean values is less than 1%. Analytical and numerical studies of sensitivity of the calculated volume fraction to temperature changes and calibration errors are also presented.

  19. Accurately measuring volume of soil samples using low cost Kinect 3D scanner

    Science.gov (United States)

    van der Sterre, Boy-Santhos; Hut, Rolf; van de Giesen, Nick

    2013-04-01

    The 3D scanner of the Kinect game controller can be used to increase the accuracy and efficiency of determining in situ soil moisture content. Soil moisture is one of the principal hydrological variables in both the water and energy interactions between soil and atmosphere. Current in situ measurements of soil moisture either rely on indirect measurements (of electromagnetic constants or heat capacity) or on physically taking a sample and weighing it in a lab. The bottleneck in accurately retrieving soil moisture using samples is the determining of the volume of the sample. Currently this is mostly done by the very time consuming "sand cone method" in which the volume were the sample used to sit is filled with sand. We show that 3D scanner that is part of the 150 game controller extension "Kinect" can be used to make 3D scans before and after taking the sample. The accuracy of this method is tested by scanning forms of known volume. This method is less time consuming and less error-prone than using a sand cone.

  20. Repeatability and reproducibility of anterior chamber volume measurements using 3-dimensional corneal and anterior segment optical coherence tomography.

    Science.gov (United States)

    Fukuda, Shinichi; Kawana, Keisuke; Yasuno, Yoshiaki; Oshika, Tetsuro

    2011-03-01

    To evaluate the repeatability and reproducibility of anterior chamber volume (ACV) measurements using swept-source 3-dimensional corneal and anterior segment optical coherence tomography (CAS-OCT) and dual Scheimpflug imaging. Department of Ophthalmology, Institute of Clinical Medicine, University of Tsukuba, Ibaraki, Japan. Nonrandomized clinical trial. Measurements were taken in normal eyes (subject group) and in eyes with primary angle closure (PAC) (patient group). In the subject group, the entire ACV and the central 8.0 mm diameter ACV were measured using CAS-OCT and dual Scheimpflug imaging. In the patient group, the entire ACV and 8.0 mm ACV were measured using CAS-OCT. The coefficient of variation and intraclass correlation coefficient (ICC) were calculated to evaluate repeatability and reproducibility, and the correlation between the 2 devices was assessed. In the subject group, the mean 8.0 mm ACV was 110.14 mm(3) ± 12.57 (SD) using CAS-OCT and 114.51 ± 14.69 mm(3) using Scheimpflug imaging; there was a significant linear correlation (r = 0.878, P ACV on CAS-OCT was 165.15 ± 29.29 mm(3). The ICCs of the 8.0 mm and entire ACV measurements were greater than 0.94. The coefficients of repeatability and reproducibility of the 8.0 mm ACV and entire ACV measurements were less than 5%. In the patient group, the 8.0 mm and entire ACV measurements showed good reproducibility and repeatability. The CAS-OCT method allowed noninvasive measurement of the entire ACV with sufficient repeatability and reproducibility. The 8.0 mm ACV measurements with CAS-OCT and Scheimpflug imaging were comparable. Copyright © 2011 ASCRS and ESCRS. Published by Elsevier Inc. All rights reserved.

  1. Volumic activities measurements and equivalent doses calculation of indoor 222Rn in Morocco

    Directory of Open Access Journals (Sweden)

    Abdelmajid Choukri

    2015-09-01

    Full Text Available Purpose: As a way of prevention, we have measured the volumic activities of indoor 222Rn and we have calculated the corresponding effective dose in some dwellings and enclosed areas in Morocco. Seasonal variation of Radon activities and Relationships between variation of these activities and some parameters such height, depth and type of construction were also established in this work.Methods: The passive time-integrated method of using a solid state nuclear track detector (LR-115 type II was employed. These films, cut in pieces of 3.4 ´ 2.5 cm2, were placed in detector holders and enclosed in heat-scaled polyethylene bags.Results: The measured volumic activities of radon vary in houses, between 31 and 136 Bq/m3 (0.55 and 2.39 mSv/year with an average value of 80 Bq/m3 (1.41 mSv/year. In enclosed work area, they vary between 60 Bq/m3 (0.38 mSv/year in an ordinary area to 1884 Bq/m3 (11.9 mSv/year at not airy underground level of 12 m. the relatively higher volumic activities of 222Rn in houses were measured in Youssoufia and khouribga towns situated in regions rich in phosphate deposits. Measurements at the geophysical observatory of Berchid show that the volumic activity of radon increases with depth, this is most probably due to decreased ventilation. Conclusion: The obtained results show that the effective dose calculated for indoor dwellings are comparable to those obtained in other regions in the word. The risks related to the volumic activities of indoor radon could be avoided by simple precautions such the continuous ventilation. The reached high value of above 1884 Bq/m3 don't present any risk for workers health in the geophysical observatory of Berchid because workers spend only a few minutes by day in the cellar to control and reregister data.

  2. Does bioimpedance analysis or measurement of natriuretic peptides aid volume assessment in peritoneal dialysis patients?

    Science.gov (United States)

    Davenport, Andrew

    2013-01-01

    Cardiovascular mortality remains the commonest cause of death for peritoneal dialysis patients. As such, preventing persistent hypervolemia is important. On the other hand, hypovolemia may potentially risk episodes of acute kidney injury and loss of residual renal function, a major determinant of peritoneal dialysis technique survival. Bioimpedance has developed from a single-frequency research tool to a multi-frequency bioelectrical impedance analysis readily available in the clinic and capable of measuring extracellular, intracellular, and total body water. Similarly, natriuretic peptides released from the heart because of myocardial stretch and increased intracardiac volume have also been variously reported to be helpful in assessing volume status in peritoneal dialysis patients. The question then arises whether these newer technologies and biomarkers have supplanted the time-honored clinical assessment of hydration status or whether they are merely adjuncts that aid the experienced clinician.

  3. Measurement of average density and relative volumes in a dispersed two-phase fluid

    Science.gov (United States)

    Sreepada, Sastry R.; Rippel, Robert R.

    1992-01-01

    An apparatus and a method are disclosed for measuring the average density and relative volumes in an essentially transparent, dispersed two-phase fluid. A laser beam with a diameter no greater than 1% of the diameter of the bubbles, droplets, or particles of the dispersed phase is directed onto a diffraction grating. A single-order component of the diffracted beam is directed through the two-phase fluid and its refraction is measured. Preferably, the refracted beam exiting the fluid is incident upon a optical filter with linearly varing optical density and the intensity of the filtered beam is measured. The invention can be combined with other laser-based measurement systems, e.g., laser doppler anemometry.

  4. Shape and deformation measurements of 3D objects using volume speckle field and phase retrieval

    DEFF Research Database (Denmark)

    Anand, A; Chhaniwal, VK; Almoro, Percival;

    2009-01-01

    Shape and deformation measurement of diffusely reflecting 3D objects are very important in many application areas, including quality control, nondestructive testing, and design. When rough objects are exposed to coherent beams, the scattered light produces speckle fields. A method to measure...... the shape and deformation of 3D objects from the sequential intensity measurements of volume speckle field and phase retrieval based on angular-spectrum propagation technique is described here. The shape of a convex spherical surface was measured directly from the calculated phase map, and micrometer......-sized deformation induced on a metal sheet was obtained upon subtraction of the phase, corresponding to unloaded and loaded states. Results from computer simulations confirm the experiments. (C) 2009 Optical Society of America....

  5. The new magnetic measurement system at the Advanced Photon Source.

    Energy Technology Data Exchange (ETDEWEB)

    Eidelman, Y.; Deriy, B.; Makarov, O.; Vasserman, I.

    2002-03-15

    A new system for precise measurements of the field integrals and multipole components of the APS magnetic insertion devices is described. A stretched coil is used to measure magnetic field characteristics. The hardware includes a number of servomotors to move (translate or rotate) the coil and a fast data acquisition board to measure the coil signal. A PC under Linux is used as a control workstation. The user interface is written as a Tcl/tk script; the hardware is accessed from the script through a shared C-library. A description of the hardware system and the control program is given.

  6. The new Magnetic Measurement System at the Advanced Photon Source

    CERN Document Server

    Eidelman, Y; Makarov, O P; Vasserman, I B; Eidelman, Yu.

    2001-01-01

    A new system for precise measurements of the field integrals and multipole components of the APS magnetic insertion devices is described. A stretched coil is used to measure magnetic field characteristics. The hardware includes a number of servomotors to move (translate or rotate) the coil and a fast data acquisition board to measure the coil signal. A PC under Linux is used as a control workstation. The user interface is written as a Tcl/tk script. The hardware is accessed from the script through a shared C-library. A description of the hardware system and the control program is given.

  7. Measurements on a little known sound source - the Vortex Whistle

    CERN Document Server

    Kristiansen, Ulf

    2016-01-01

    Acoustic measurements on a vortex whistle corroborates earlier findings that the frequency increases linearly with the velocity of the air flowing into the whistle. Measurements in a reverberant chamber shows that the acoustic power generated by the whistle increases close to the sixth power of the frequency. PIV and hot-wire measurements give quantitative information on the flow. It is shown that the flow exits the pipe as a swirling annulus with a rotation corresponding to the frequency of the sound, and that the center of the swirl follows a nearly circular path in the exit plane. The PIV measurements also indicate a toroidal vortex with inflow along the center line close to the exit of the whistle.

  8. Measurements and modeling of the volume scattering function in the coastal northern Adriatic Sea

    Science.gov (United States)

    Berthon, Jean-François; Shybanov, Eugeny; Lee, Michael E.-G.; Zibordi, Giuseppe

    2007-08-01

    We performed measurements of the volume scattering function (VSF) between 0.5° and 179° with an angular resolution of 0.3° in the northern Adriatic Sea onboard an oceanographic platform during three different seasons, using the multispectral volume scattering meter (MVSM) instrument. We observed important differences with respect to Petzold's commonly used functions, whereas the Fournier-Forand's analytical formulation provided a rather good description of the measured VSF. The comparison of the derived scattering, bp(λ) and backscattering, bbp(λ) coefficients for particles with the measurements performed with the classical AC-9 and Hydroscat-6 showed agreement to within 20%. The use of an empirical relationship for the derivation of bb(λ) from β(ψ,λ) at ψ=140° was validated for this coastal site although ψ=118° was confirmed to be the most appropriate angle. The low value of the factor used to convert β(ψ,λ) into bb(λ) within the Hydroscat-6 processing partially contributed to the underestimation of bb(λ) with respect to the MVSM. Finally, use of the Kopelevich model together with a measurement of bp(λ) at λ=555 nm allowed us to reconstruct the VSF with average rms percent differences between 8 and 15%.

  9. Volume weighting the measure of the universe from classical slow-roll expansion

    Science.gov (United States)

    Sloan, David; Silk, Joseph

    2016-05-01

    One of the most frustrating issues in early universe cosmology centers on how to reconcile the vast choice of universes in string theory and in its most plausible high energy sibling, eternal inflation, which jointly generate the string landscape with the fine-tuned and hence relatively small number of universes that have undergone a large expansion and can accommodate observers and, in particular, galaxies. We show that such observations are highly favored for any system whereby physical parameters are distributed at a high energy scale, due to the conservation of the Liouville measure and the gauge nature of volume, asymptotically approaching a period of large isotropic expansion characterized by w =-1 . Our interpretation predicts that all observational probes for deviations from w =-1 in the foreseeable future are doomed to failure. The purpose of this paper is not to introduce a new measure for the multiverse, but rather to show how what is perhaps the most natural and well-known measure, volume weighting, arises as a consequence of the conservation of the Liouville measure on phase space during the classical slow-roll expansion.

  10. Measuring tree height and preparation volume table using an innovative method.

    Science.gov (United States)

    Lotfalian, Majid; Nouri, Zahra; Kooch, Yahya; Zobeiri, Mahmoud

    2007-10-15

    Zarbin (Cupressus sempervirence var. horizontalis) with its unique characteristics is one of the worthiest species which can be found in the central area of Alborz in the North of Iran. Especially in the Roodbar-manjil area, Chaloos-Hassanabad valley as well as it extends from Zarringol area to Gorgan. Although the distribution areas of this species have been protected, these forests have been invaded by the villagers who use this useful wood. For this reason in the Roodbar area, trees with DBH>30 cm are extremely rare. To recognize and to be aware of the stand quantity, the current research tries to calculate the species volume table in Roodbar area, to be the basis for any calculation of the volume of stand in the region. For this purpose, trees have been sampled using the line sampling method. After estimating the form factor, Tarif table have been prepared. In this study, a new method for measuring tree height is presented, in which, instead of measuring slope distance from observer to tree (which is difficult in young conifers because of existence branches in lower height) distance between the eye level of observer to tree butt is measured. Which doing of it is easier, time of field work is decreased and accuracy of measurement and calculation is increased.

  11. Paul Scherrer Institute Scientific Report 1999. Volume VII: Swiss Light Source

    Energy Technology Data Exchange (ETDEWEB)

    Weyer, Heinz Josef; Bugmann, Marlen; Schuetz, Christine [eds.

    2000-07-01

    The Swiss Synchrotron Light Source (SLS) is a medium energy range light source that also provides light with high brilliance in the regime of hard X-rays. It is being constructed at PSI and scheduled to be operational in 2001. The progress of the construction of pre-injector, booster and storage ring as well as some of the details of new features that were adopted for the design and operation of this machine, are described in this annual report for 1999. An overview of the concept and status of the four SLS beamlines and the related infrastructure is also given. The last chapter contains 11 contributions which report on scientific activities of SLS staff members at synchrotron radiation facilities all over the world.

  12. Singles transmission in volume-imaging PET with a 137Cs source.

    Science.gov (United States)

    Karp, J S; Muehllehner, G; Qu, H; Yan, X H

    1995-05-01

    The feasibility of a new method of attenuation correction in PET has been investigated, using a single-photon emitter for the transmission scan. The transmission scan is predicted to be more than a factor of ten faster with the singles method than the standard coincidence method, for comparable statistics. Thus, a transmission scan be completed in 1-2 min, rather than 10-20 min, as is common practice with the coincidence method. In addition, a potential advantage of using the single-photon source 137Cs, which has an energy of 662 keV, is that postinjection transmission studies can be performed using energy discrimination to separate the transmission from the emission data at 511 keV. In order to compensate for the energy difference of the attenuation coefficients at 662 keV compared to 511 keV, the transmission images are segmented into two compartments, tissue and lung, and known values (for 511 keV) of attenuation are inserted into these compartments. This technique also compensates for the higher amount of scatter present with the singles method, since it is not possible to use a position gate (based on collinearity of the source and two detector positions) as is commonly done with a positron-emitting source. We have demonstrated, with experimental phantom studies, that the singles transmission method combined with segmentation gives results equivalent both qualitatively and quantitatively to the coincidence method, but requires significantly less time.

  13. Sourcing tactics to achieve cost savings: developing a formative method of measurement

    NARCIS (Netherlands)

    Hesping, Frank; Schiele, Holger

    2016-01-01

    Sourcing levers describe tactics to achieve sourcing targets for diverse categories of materials or services. However, relevant research has been prevented inasmuch as the sourcing lever concept lacks explicit conceptualisation and a method of measurement. To fill this gap, this study developed a

  14. Sourcing tactics to achieve cost savings: developing a formative method of measurement

    NARCIS (Netherlands)

    Hesping, Frank; Schiele, Holger

    2016-01-01

    Sourcing levers describe tactics to achieve sourcing targets for diverse categories of materials or services. However, relevant research has been prevented inasmuch as the sourcing lever concept lacks explicit conceptualisation and a method of measurement. To fill this gap, this study developed a fo

  15. A review of international sources for road safety measures assessment.

    NARCIS (Netherlands)

    Yannis, G. Weijermars, W. & Kauppila, J.

    2012-01-01

    The efficiency assessment of road safety measures is considered to be an extremely useful tool in decision making; in particular, cost-benefit and cost-effectiveness analyses are carried out in several countries, in a more or less systematic way. The objective of this paper is to present findings fr

  16. Open-source algorithm for automatic choroid segmentation of OCT volume reconstructions

    Science.gov (United States)

    Mazzaferri, Javier; Beaton, Luke; Hounye, Gisèle; Sayah, Diane N.; Costantino, Santiago

    2017-02-01

    The use of optical coherence tomography (OCT) to study ocular diseases associated with choroidal physiology is sharply limited by the lack of available automated segmentation tools. Current research largely relies on hand-traced, single B-Scan segmentations because commercially available programs require high quality images, and the existing implementations are closed, scarce and not freely available. We developed and implemented a robust algorithm for segmenting and quantifying the choroidal layer from 3-dimensional OCT reconstructions. Here, we describe the algorithm, validate and benchmark the results, and provide an open-source implementation under the General Public License for any researcher to use (https://www.mathworks.com/matlabcentral/fileexchange/61275-choroidsegmentation).

  17. CADDIS Volume 2. Sources, Stressors and Responses: Insecticides - Detailed Conceptual Diagram

    Science.gov (United States)

    Introduction to the insecticides module, when to list insecticides as a candidate cause, ways to measure insecticides, simple and detailed conceptual diagrams for insecticides, insecticides module references and literature reviews.

  18. CADDIS Volume 2. Sources, Stressors and Responses: Insecticides - Simple Conceptual Diagram

    Science.gov (United States)

    Introduction to the insecticides module, when to list insecticides as a candidate cause, ways to measure insecticides, simple and detailed conceptual diagrams for insecticides, insecticides module references and literature reviews.

  19. CADDIS Volume 2. Sources, Stressors and Responses: Nutrients - Detailed Conceptual Diagram (P)

    Science.gov (United States)

    Introduction to the nutrients module, when to list nutrients as a candidate cause, ways to measure nutrients, simple and detailed conceptual diagrams for nutrients, nutrients module references and literature reviews.

  20. CADDIS Volume 2. Sources, Stressors and Responses: Nutrients - Detailed Conceptual Diagram (N)

    Science.gov (United States)

    Introduction to the nutrients module, when to list nutrients as a candidate cause, ways to measure nutrients, simple and detailed conceptual diagrams for nutrients, nutrients module references and literature reviews.

  1. CADDIS Volume 2. Sources, Stressors and Responses: Nutrients - Simple Conceptual Diagram

    Science.gov (United States)

    Introduction to the nutrients module, when to list nutrients as a candidate cause, ways to measure nutrients, simple and detailed conceptual diagrams for nutrients, nutrients module references and literature reviews.

  2. Measurement of anterior chamber volume with rotating scheimpflug camera and anterior segment optical coherence tomography

    Institute of Scientific and Technical Information of China (English)

    FU Jing; LI Shu-ning; WANG Xiao-zhen; WU Ge-wei; MU Da-peng; WANG Jian; WANG Ning-li

    2010-01-01

    Background Measurement of anterior segment parameters plays an important role in diagnosis and treatment of glaucoma. The objective of this study was to evaluate the repeatability and reproducibility of anterior chamber volume (ACV) measurements with rotating scheimpflug camera (RSC) and to examine agreement with anterior segment optical coherence tomography (AS-OCT). Methods Thirty nine healthy normal subjects were recruited from the Eye Center of Tongren Hospital. ACV was measured using RSC and AS-OCT in a randomly selected eye for each subject. For RSC measurements, both automatic and manual ACV measurements and 2 independent operators' ACV measurements were obtained. All subjects were invited for 3 visits within a week to evaluate repeatability and reproducibility of ACV measurement by RSC. Agreement was evaluated between RSC and AS-OCT. Results Good repeatability and reproducibility were found for both automatic and manual ACV measurements obtained by RSC. For intrasession repeatability, coefficient of variation (CVw) and intraclass correlation coefficient (ICC) values for automatic were 3.52% and 0.98; the values for manual were 3.44% and 0.97, respectively. For intersession reproducibility, the respective CVw and ICC values were 3.96% and 0.96. Good agreement was also found in 2 operators for both automatic and manual ACV measurements; nevertheless, poor agreement was found between RSC and AS-OCT (95% confidence interval (CI) for agreement of automatic RSC measurement versus AS-OCT were -96.3 to 72.8 μl and 95% CI for agreement of manual RSC measurement versus AS-OCT were between -41.7 to 10.1 μl). Conclusions Both RSC automatic and manual ACV measurements showed good repeatability and reproducibility, and showed comparable agreement between 2 independent operators, but poor agreement was found between RSC and AS-OCT.

  3. Measurement of anterior chamber volume with rotating scheimpflug camera and anterior segment optical coherence tomography.

    Science.gov (United States)

    Fu, Jing; Li, Shu-ning; Wang, Xiao-zhen; Wu, Ge-wei; Mu, Da-peng; Wang, Jian; Wang, Ning-li

    2010-01-20

    Measurement of anterior segment parameters plays an important role in diagnosis and treatment of glaucoma. The objective of this study was to evaluate the repeatability and reproducibility of anterior chamber volume (ACV) measurements with rotating scheimpflug camera (RSC) and to examine agreement with anterior segment optical coherence tomography (AS-OCT). Thirty nine healthy normal subjects were recruited from the Eye Center of Tongren Hospital. ACV was measured using RSC and AS-OCT in a randomly selected eye for each subject. For RSC measurements, both automatic and manual ACV measurements and 2 independent operators' ACV measurements were obtained. All subjects were invited for 3 visits within a week to evaluate repeatability and reproducibility of ACV measurement by RSC. Agreement was evaluated between RSC and AS-OCT. Good repeatability and reproducibility were found for both automatic and manual ACV measurements obtained by RSC. For intrasession repeatability, coefficient of variation (CVw) and intraclass correlation coefficient (ICC) values for automatic were 3.52% and 0.98; the values for manual were 3.44% and 0.97, respectively. For intersession reproducibility, the respective CVw and ICC values were 3.96% and 0.96. Good agreement was also found in 2 operators for both automatic and manual ACV measurements; nevertheless, poor agreement was found between RSC and AS-OCT (95% confidence interval (CI) for agreement of automatic RSC measurement versus AS-OCT were -96.3 to 72.8 microl and 95% CI for agreement of manual RSC measurement versus AS-OCT were between -41.7 to 10.1 microl). Both RSC automatic and manual ACV measurements showed good repeatability and reproducibility, and showed comparable agreement between 2 independent operators, but poor agreement was found between RSC and AS-OCT.

  4. Formation of uniform fringe pattern free from diffraction noise at LDA measurement volume using holographic imaging configuration

    Science.gov (United States)

    Ghosh, Abhijit; Nirala, A. K.

    2016-05-01

    In the present study we have proposed a technique for improving fringe quality at laser Doppler anemometry measurement volume in real time using single hololens imaging configuration over conventional imaging configuration with Gaussian beam optics. In order to remove interference fringe gradients as well as higher order diffraction noise formed at measurement volume in the former approach, a combined hololens imaging system has also been proposed. For qualitative as well as quantitative analysis of fringes formed at measurement volume, atomic force microscopy (AFM) analysis has been performed.

  5. A Polypyrrole-based Strain Sensor Dedicated to Measure Bladder Volume in Patients with Urinary Dysfunction

    Directory of Open Access Journals (Sweden)

    Vamsy P. Chodavarapu

    2008-08-01

    Full Text Available This paper describes a new technique to measure urine volume in patients with urinary bladder dysfunction. Polypyrrole – an electronically conducting polymer - is chemically deposited on a highly elastic fabric. This fabric, when placed around a phantom bladder, produced a reproducible change in electrical resistance on stretching. The resistance response to stretching is linear in 20%-40% strain variation. This change in resistance is influenced by chemical fabrication conditions. We also demonstrate the dynamic mechanical testing of the patterned polypyrrole on fabric in order to show the feasibility of passive interrogation of the strain sensor for biomedical sensing applications.

  6. Improvement of fringe quality at LDA measuring volume using compact two hololens imaging system

    Science.gov (United States)

    Ghosh, Abhijit; Nirala, A. K.

    2015-03-01

    Design, analysis and construction of an LDA optical setup using conventional as well as compact two hololens imaging system have been performed. Fringes formed at measurement volume by both the imaging systems have been recorded. After experimentally analyzing these fringes, it is found that fringes obtained using compact two hololens imaging system get improved both qualitatively and quantitatively compared to that obtained using conventional imaging system. Hence it is concluded that use of the compact two hololens imaging system for making LDA optical setup is a better choice over the conventional one.

  7. Volume-Averaged Model of Inductively-Driven Multicusp Ion Source

    Science.gov (United States)

    Patel, Kedar K.; Lieberman, M. A.; Graf, M. A.

    1998-10-01

    A self-consistent spatially averaged model of high-density oxygen and boron trifluoride discharges has been developed for a 13.56 MHz, inductively coupled multicusp ion source. We determine positive ion, negative ion, and electron densities, the ground state and metastable densities, and the electron temperature as functions of the control parameters: gas pressure, gas flow rate, input power and reactor geometry. Neutralization and fragmentation into atomic species are assumed for all ions hitting the wall. For neutrals, a wall recombination coefficient for oxygen atoms and a wall sticking coefficient for boron trifluoride (BF_3) and its dissociation products are the single adjustable parameters used to model the surface chemistry. For the aluminum walls of the ion source used in the Eaton ULE2 ion implanter, complete wall recombination of O atoms is found to give the best match to the experimental data for oxygen, whereas a sticking coefficient of 0.62 for all neutral species in a BF3 discharge was found to best match experimental data.

  8. Paul Scherrer Institute Scientific Report 2000. Volume VII: Swiss Light Source

    Energy Technology Data Exchange (ETDEWEB)

    Weyer, Heinz Josef; Bugmann, Marlen; Schuetz, Christine [eds.

    2001-07-01

    The Swiss Synchrotron Light Source (SLS) is a medium energy range light source that also provides light with high brilliance in the regime of hard X-rays. It is presently being constructed at PSI. The year 2000 was crucial for maintaining the project milestones with the start of storage ring commissioning for beginning of 2001 and first light on the probe at the four beamlines of phase I for August 2001. The major goals of 2000 were the completion of accelerator installation, the commissioning of linac and booster and the beginning of beamline assembly. In the first half of the year in parallel to the installation, major fabrication procedures were going on, that had to be thoroughly followed up in order to guarantee their completion in time. The overview and detailed description of these developments is supplemented in this annual report by 8 contributions on scientific activities of SLS staff members at synchrotron radiation facilities all over the world. A list of scientific publications in 2000 is also provided.

  9. A white matter lesion-filling approach to improve brain tissue volume measurements

    Directory of Open Access Journals (Sweden)

    Sergi Valverde

    2014-01-01

    Full Text Available Multiple sclerosis white matter (WM lesions can affect brain tissue volume measurements of voxel-wise segmentation methods if these lesions are included in the segmentation process. Several authors have presented different techniques to improve brain tissue volume estimations by filling WM lesions before segmentation with intensities similar to those of WM. Here, we propose a new method to refill WM lesions, where contrary to similar approaches, lesion voxel intensities are replaced by random values of a normal distribution generated from the mean WM signal intensity of each two-dimensional slice. We test the performance of our method by estimating the deviation in tissue volume between a set of 30 T1-w 1.5 T and 30 T1-w 3 T images of healthy subjects and the same images where: WM lesions have been previously registered and afterwards replaced their voxel intensities to those between gray matter (GM and WM tissue. Tissue volume is computed independently using FAST and SPM8. When compared with the state-of-the-art methods, on 1.5 T data our method yields the lowest deviation in WM between original and filled images, independently of the segmentation method used. It also performs the lowest differences in GM when FAST is used and equals to the best method when SPM8 is employed. On 3 T data, our method also outperforms the state-of-the-art methods when FAST is used while performs similar to the best method when SPM8 is used. The proposed technique is currently available to researchers as a stand-alone program and as an SPM extension.

  10. 76 FR 53897 - EPA Seeking Input Materials Measurement; Municipal Solid Waste (MSW), Recycling, and Source...

    Science.gov (United States)

    2011-08-30

    ... From the Federal Register Online via the Government Publishing Office ENVIRONMENTAL PROTECTION AGENCY EPA Seeking Input Materials Measurement; Municipal Solid Waste (MSW), Recycling, and Source... management, recycling, measurement, data, data collection, construction and demolition (C&D)...

  11. Effect of Sound Source Scattering on Measurement of Near-Field Head-Related Transfer Functions

    Institute of Scientific and Technical Information of China (English)

    YU Guang-Zheng; XIE Bo-Sun; RAO Dan

    2008-01-01

    @@ A simple spherical head and pulsating spherical sound source model are proposed to investigate the effect of multiple scattering between the head and the sound source on near-field head-related transfer function (HRTF) measurement. Multipole expansion method is used to calculate HRTFs of the model, then the relationships among the magnitude error of HRTF with frequency, source direction, source size, and the distance between the head centre and the sound source are analysed. The results show that to ensure the magnitude error of HRTF within 1.0 dB up to 20 kHz, for source distance not less than 0.15m or 0.20 m, the radius of the sound source should not exceed 0.03 m or 0.05 m, respectively. The conclusion suggests an appropriate size of sound source in near-field HRTF measurement.

  12. Volume Measurements of Laser-generated Pits for In Situ Geochronology using KArLE (Potassium-Argon Laser Experiment)

    Science.gov (United States)

    French, R. A.; Cohen, B. A.; Miller, J. S.

    2014-01-01

    The Potassium-Argon Laser Experiment( KArLE), is composed of two main instruments: a spectrometer as part of the Laser-Induced Breakdown Spectroscopy (LIBS) method and a Mass Spectrometer (MS). The LIBS laser ablates a sample and creates a plasma cloud, generating a pit in the sample. The LIBS plasma is measured for K abundance in weight percent and the released gas is measured using the MS, which calculates Ar abundance in mols. To relate the K and Ar measurements, total mass of the ablated sample is needed but can be difficult to directly measure. Instead, density and volume are used to calculate mass, where density is calculated based on the elemental composition of the rock (from the emission spectrum) and volume is determined by pit morphology. This study aims to reduce the uncertainty for KArLE by analyzing pit volume relationships in several analog materials and comparing methods of pit volume measurements and their associated uncertainties.

  13. Assessing Model Characterization of Single Source Secondary Pollutant Impacts Using 2013 SENEX Field Study Measurements.

    Science.gov (United States)

    Baker, Kirk R; Woody, Matthew C

    2017-03-15

    Aircraft measurements made downwind from specific coal fired power plants during the 2013 Southeast Nexus field campaign provide a unique opportunity to evaluate single source photochemical model predictions of both O3 and secondary PM2.5 species. The model did well at predicting downwind plume placement. The model shows similar patterns of an increasing fraction of PM2.5 sulfate ion to the sum of SO2 and PM2.5 sulfate ion by distance from the source compared with ambient based estimates. The model was less consistent in capturing downwind ambient based trends in conversion of NOX to NOY from these sources. Source sensitivity approaches capture near-source O3 titration by fresh NO emissions, in particular subgrid plume treatment. However, capturing this near-source chemical feature did not translate into better downwind peak estimates of single source O3 impacts. The model estimated O3 production from these sources but often was lower than ambient based source production. The downwind transect ambient measurements, in particular secondary PM2.5 and O3, have some level of contribution from other sources which makes direct comparison with model source contribution challenging. Model source attribution results suggest contribution to secondary pollutants from multiple sources even where primary pollutants indicate the presence of a single source.

  14. Intercorrelations of Anthropometric Measurements: A Source Book for USA Data

    Science.gov (United States)

    1978-05-01

    The surface distance, along the spine, from waist level to cervicale , to the tip of the 7th cervical vertebra . 924. Waist Breadth. The breadth of the...leg. 219. Cervicale Height. The height of cervicale . 223. Chest Breadth. The breadth of the torso measured at nipple level. 227. Chest Breadth (Bone...the tape held tense and not following the body contour. 637. Neck- Cervicale Length. The tape distance from cervicale to the superior point of the

  15. The accuracy and optimal slice thickness of multislice helical computed tomography for right and left ventricular volume measurement

    Institute of Scientific and Technical Information of China (English)

    崔炜; 近藤武; 安野泰史; 郭玉印; 佐藤贵久; 皿井正義; 篠崎仁史; 柿澤聡士; 杉浦厚司; 大岛慶太; 片田和廣; 菱田仁

    2004-01-01

    Background Multislice helical computed tomography (MSCT) has been used to depict coronary anatomy noninvasively, and proved useful for evaluating ventricular function. The aim of our study was to assess the accuracy of ventricular volume as measured by MSCT. Methods Fourteen human left ventricular (LV) and 15 right ventricular (RV) casts were scanned by MSCT. A series of LV and RV short-axis images were reconstructed later with slice thickness of 2.0 mm, 3.5 mm, 5.0 mm, 7.0 mm, and 10.0 mm. Ventricular volume was calculated by the multislice tomographic Simpson's method. True LV and RV cast volumes were determined by water displacement. Results Both calculated LV and RV volumes correlated highly with the corresponding true volumes (all r>0.95, P<0.01). But with slice thickness from 2.0 mm to 10.0 mm, MSCT scanning overestimated the corresponding true volume by (3.21±5.95) ml to (12.58±8.56) ml for LV and (10.22±8.45) ml to (23.91±12.24) ml for RV (all P<0.01). There was a very high correlation between the overestimation and the selected slice thickness for both LV and RV volume measurements (r=0.998 and 0.996, P<0.01, respectively). However, when slice thickness was reduced to 5.0 mm, the overestimation for both LV and RV volume measurements became nonsignificant for slice thickness from 2.0 mm to 5.0 mm. Conclusions Both LV and RV volumes can be accurately estimated by MSCT. Thinner slice has more accurate calculated volume. However, 5.0 mm slice thickness is thin enough for an accurate measurement of LV or RV volume.

  16. A multiple-source consecutive localization algorithm based on quantized measurement for wireless sensor network

    Science.gov (United States)

    Chu, Hao; Wu, Chengdong

    2016-10-01

    The source localization base on wireless sensor network has attracted considerable attention in recent years. However, most of the previous works focus on the accurate measurement or single source localization. The multiple-source localization has extensive application prospect in many fields. The quantized measurement is a low-cost and low energy consumption solution for wireless sensor network. In this paper, we present a novel multiple-source consecutive localization algorithm using the quantized measurement. We first introduce the multiple acoustic sources model and quantized measurement method. Then the maximum likelihood method is used to establish the localization function and the particle swarm optimization is employed to estimate the initial position of the source. Finally the Kalman filter is used to mitigate the random processing noise. Simulation results show that the proposed method owns high localization accuracy.

  17. Time-specific measurements of energy deposition from radiation fields in simulated sub-micron tissue volumes

    Energy Technology Data Exchange (ETDEWEB)

    Famiano, M.A.

    1997-07-07

    A tissue-equivalent spherical proportional counter is used with a modified amplifier system to measure specific energy deposited from a uniform radiation field for short periods of time ({approximately}1 {micro}s to seconds) in order to extrapolate to dose in sub-micron tissue volumes. The energy deposited during these time intervals is compared to biological repair processes occurring within the same intervals after the initial energy deposition. The signal is integrated over a variable collection time which is adjusted with a square-wave pulse. Charge from particle passages is collected on the anode during the period in which the integrator is triggered, and the signal decays quickly to zero after the integrator feedback switch resets; the process repeats for every triggering pulse. Measurements of energy deposited from x rays, {sup 137}Cs gamma rays, and electrons from a {sup 90}Sr/{sup 90}Y source for various time intervals are taken. Spectral characteristics as a function of charge collection time are observed and frequency plots of specific energy and collection time-interval are presented. In addition, a threshold energy flux is selected for each radiation type at which the formation of radicals (based on current measurements) in mammalian cells equals the rate at which radicals are repaired.

  18. New source performance standards for industrial boilers. Volume 2. Review of industry operating practices

    Energy Technology Data Exchange (ETDEWEB)

    Bryan, R.J.; Weisenberg, I.J.; Wilson, K.

    1980-09-01

    The applicability is evaluated of several possible versions of a revised New Source Performance Standards (NSPS) for industrial boilers to boilers that are operated according to typical industry practices. A survey of operating practices is presented, and it is concluded that an NSPS that includes too high a percent removal requirement for SO/sub 2/ (90%) might be excessively costly and cause operating problems for the industrial operator. More field evaluations of low excess air and low Btu gasification are required to validate these techniques for pollution control under industrial boiler operating conditions. The cost of two small boilers with no SO/sub 2/ controls was less than one large boiler of twice the capacity with SO/sub 2/ controls. The annual cost of operating and maintaining the control system accounted for the difference.

  19. Advisory Committee on human radiation experiments. Supplemental Volume 2a, Sources and documentation appendices. Final report

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-01-01

    This large document provides a catalog of the location of large numbers of reports pertaining to the charge of the Presidential Advisory Committee on Human Radiation Research and is arranged as a series of appendices. Titles of the appendices are Appendix A- Records at the Washington National Records Center Reviewed in Whole or Part by DoD Personnel or Advisory Committee Staff; Appendix B- Brief Descriptions of Records Accessions in the Advisory Committee on Human Radiation Experiments (ACHRE) Research Document Collection; Appendix C- Bibliography of Secondary Sources Used by ACHRE; Appendix D- Brief Descriptions of Human Radiation Experiments Identified by ACHRE, and Indexes; Appendix E- Documents Cited in the ACHRE Final Report and other Separately Described Materials from the ACHRE Document Collection; Appendix F- Schedule of Advisory Committee Meetings and Meeting Documentation; and Appendix G- Technology Note.

  20. National Synchrotron Light Source annual report 1991. Volume 1, October 1, 1990--September 30, 1991

    Energy Technology Data Exchange (ETDEWEB)

    Hulbert, S.L.; Lazarz, N.M. [eds.

    1992-04-01

    This report discusses the following research conducted at NSLS: atomic and molecular science; energy dispersive diffraction; lithography, microscopy and tomography; nuclear physics; UV photoemission and surface science; x-ray absorption spectroscopy; x-ray scattering and crystallography; x-ray topography; workshop on surface structure; workshop on electronic and chemical phenomena at surfaces; workshop on imaging; UV FEL machine reviews; VUV machine operations; VUV beamline operations; VUV storage ring parameters; x-ray machine operations; x-ray beamline operations; x-ray storage ring parameters; superconducting x-ray lithography source; SXLS storage ring parameters; the accelerator test facility; proposed UV-FEL user facility at the NSLS; global orbit feedback systems; and NSLS computer system.

  1. Measuring x-ray spectra of flash radiographic sources [PowerPoint

    Energy Technology Data Exchange (ETDEWEB)

    Gehring, Amanda Elizabeth [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Espy, Michelle A. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Haines, Todd Joseph [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Mendez, Jacob [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Moir, David C. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Sedillo, Robert [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Shurter, Roger P. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Volegov, Petr Lvovich [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Webb, Timothy J [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2015-11-02

    The x-ray spectra of flash radiographic sources are difficult to measure. The sources measured were Radiographic Integrated Test Stand-6 (370 rad at 1 m; 50 ns pulse) and Dual Axis Radiographic Hydrodynamic Test Facility (DARHT) (550 rad at 1 m; 50 ns pulse). Features of the Compton spectrometer are described, and spectra are shown. Additional slides present data on instrumental calibration.

  2. 'Orbital volume restoration rate after orbital fracture'; a CT-based orbital volume measurement for evaluation of orbital wall reconstructive effect.

    Science.gov (United States)

    Wi, J M; Sung, K H; Chi, M

    2017-01-13

    PurposeTo evaluate the effect of orbital reconstruction and factors related to the effect of orbital reconstruction by assessing of orbital volume using orbital computed tomography (CT) in cases of orbital wall fracture.MethodsIn this retrospective study, 68 patients with isolated blowout fractures were evaluated. The volumes of orbits and herniated orbital tissues were determined by CT scans using a three-dimensional reconstruction technique (the Eclipse Treatment Planning System). Orbital CT was performed preoperatively, immediately after surgery, and at final follow ups (minimum of 6 months). We evaluated the reconstructive effect of surgery making a new formula, 'orbital volume reconstruction rate' from orbital volume differences between fractured and contralateral orbits before surgery, immediately after surgery, and at final follow up.ResultsMean volume of fractured orbits before surgery was 23.01±2.60 cm(3) and that of contralateral orbits was 21.31±2.50 cm(3) (P=0.005). Mean volume of the fractured orbits immediately after surgery was 21.29±2.42 cm(3), and that of the contralateral orbits was 21.33±2.52 cm(3) (P=0.921). Mean volume of fractured orbits at final follow up was 21.50±2.44 cm(3), and that of contralateral orbits was 21.32±2.50 cm(3) (P=0.668). The mean orbital volume reconstruction rate was 100.47% immediately after surgery and 99.17% at final follow up. No significant difference in orbital volume reconstruction rate was observed with respect to fracture site or orbital implant type. Patients that underwent operation within 14 days of trauma had a better reconstruction rate at final follow up than patients who underwent operation over 14 days after trauma (P=0.039).ConclusionComputer-based measurements of orbital fracture volume can be used to evaluate the reconstructive effect of orbital implants and provide useful quantitative information. Significant reduction of orbital volume is observed immediately after orbital wall

  3. Measurement of accidental coincidences for higher activity sources

    CERN Document Server

    Yull Hwang, H; Jae-Oh, P; Man-Lee, J; Kie-Lee, M

    1999-01-01

    The multi-channel time-scaling (MCTS) technique has been applied for the measurement of accidental coincidences for the cases of higher activity samples in beta-gamma coincidence counting. Two beta samples of sup 1 sup 3 sup 4 Cs were prepared and the nominal activities observed in the beta counter were about 7000 and 11000 s sup - sup 1 , respectively. The obtained true coincidence rates are independent of resolving times and dead times. They are compared with those calculated from the mathematical model derived by Cox and Isham.

  4. Development of a plume-in-grid model for industrial point and volume sources: application to power plant and refinery sources in the Paris region

    Science.gov (United States)

    Kim, Y.; Seigneur, C.; Duclaux, O.

    2014-04-01

    Plume-in-grid (PinG) models incorporating a host Eulerian model and a subgrid-scale model (usually a Gaussian plume or puff model) have been used for the simulations of stack emissions (e.g., fossil fuel-fired power plants and cement plants) for gaseous and particulate species such as nitrogen oxides (NOx), sulfur dioxide (SO2), particulate matter (PM) and mercury (Hg). Here, we describe the extension of a PinG model to study the impact of an oil refinery where volatile organic compound (VOC) emissions can be important. The model is based on a reactive PinG model for ozone (O3), which incorporates a three-dimensional (3-D) Eulerian model and a Gaussian puff model. The model is extended to treat PM, with treatments of aerosol chemistry, particle size distribution, and the formation of secondary aerosols, which are consistent in both the 3-D Eulerian host model and the Gaussian puff model. Furthermore, the PinG model is extended to include the treatment of volume sources to simulate fugitive VOC emissions. The new PinG model is evaluated over Greater Paris during July 2009. Model performance is satisfactory for O3, PM2.5 and most PM2.5 components. Two industrial sources, a coal-fired power plant and an oil refinery, are simulated with the PinG model. The characteristics of the sources (stack height and diameter, exhaust temperature and velocity) govern the surface concentrations of primary pollutants (NOx, SO2 and VOC). O3 concentrations are impacted differently near the power plant than near the refinery, because of the presence of VOC emissions at the latter. The formation of sulfate is influenced by both the dispersion of SO2 and the oxidant concentration; however, the former tends to dominate in the simulations presented here. The impact of PinG modeling on the formation of secondary organic aerosol (SOA) is small and results mostly from the effect of different oxidant concentrations on biogenic SOA formation. The investigation of the criteria for injecting

  5. Measured Performance of a Low Temperature Air Source Heat Pump

    Energy Technology Data Exchange (ETDEWEB)

    Johnson, R. K. [Johnson Research LLC, Pueblo West, CO (United States)

    2013-09-01

    A 4-ton Low Temperature Heat Pump (LTHP) manufactured by Hallowell International was installed in a residence near New Haven, Connecticut and monitored over two winters of operation. After attending to some significant service issues, the heat pump operated as designed. This report should be considered a review of the dual compressor 'boosted heat pump' technology. The Low Temperature Heat Pumpsystem operates with four increasing levels of capacity (heat output) as the outdoor temperature drops. The system was shown to select capacity correctly, supplying the appropriate amount of heat to the house across the full range of outdoor temperatures. The system's Coefficient of Performance (Seasonal COP, or SCOP) over two entire winters was calculated, based on measured data, to be 3.29over the first winter and 2.68 over the second winter. A second seasonal efficiency calculation by a different method yielded a SCOP of 2.78 for the first winter and 2.83 for the second winter. This second seasonal efficiency calculation was determined by comparing measured heat pump energy use to the in situ energy use with resistance heat alone. This method is the ratio of the slopes of thedaily energy use load lines.

  6. Velocity measurements in jets with application to noise source modeling

    Science.gov (United States)

    Morris, Philip J.; Zaman, K. B. M. Q.

    2010-02-01

    This paper describes an experimental investigation of the statistical properties of turbulent velocity fluctuations in an axisymmetric jet. The focus is on those properties that are relevant to the prediction of noise. Measurements are performed using two single hot-wire anemometers as well as a two-component anemometer. Two-point cross correlations of the axial velocity fluctuations and of the fluctuations in the square of the axial velocity fluctuations are presented. Several reference locations in the jet are used including points on the jet lip and centerline. The scales of the turbulence and the convection velocity are determined, both in an overall sense as well as a function of frequency. The relationship between the second and fourth order correlations is developed and compared with the experimental data. The implications of the use of dimensional as well as non-dimensional correlations are considered. Finally, a comparison is made between the length scales deduced from the flow measurements and a RANS CFD calculation.

  7. Measurement of tumor volumes of hepatocellular carcinoma (HCC) by computed tomography (CT). Correlation with several tumor markers

    Energy Technology Data Exchange (ETDEWEB)

    Yoneshima, Manabu; Sawabu, Norio; Toya, Daishu

    1984-09-01

    Tumor volumes of HCC were measured by CT using planimeter and the clinical value of this measurement was evaluated by comparing several tumor markers. Tumor volumes measured by CT roughly agreed with those measured by angiography. In some cases, volumes from ultrasonography were smaller than those from CT and angiography. Tumor volumes measured by CT correlated significantly with the levels of ..cap alpha..-fetoprotein (AFP) but didn't relate to the presence of hepatoma specific ..gamma..-GTP isoenzyme (novel ..gamma..-GTP) nor to the values and positivities of LAI assay. In small HCCs (<=30 cm/sup 3/), the presence of novel ..gamma..-GTP and the levels of AFP were significantly lower than for larger tumors of HCC, but LAI assay wasn't lower. The non-tumorous volumes and the ratio of the non-tumorous volume to the whole liver volume didn't relate to the tests of liver function except for the presence of ascites.

  8. Importance of evaluation of uncertainties on the measurement of natural gas and petroleum volumes; Importancia da avaliacao das incertezas na medicao dos volumes de petroleo e gas natural

    Energy Technology Data Exchange (ETDEWEB)

    Silva Filho, Jose Alberto Pinheiro da; Oliveira, Thiago Barra Vidal de; Mata, Josaphat Dias da [PETROBRAS, Rio de Janeiro, RJ (Brazil)], Emails: jose.pinheiro@petrobras.com.br, thiagovidal@petrobras.com.br, josaphat@petrobras.com.br; Val, Luiz Gustavo do [Instituto de Qualidade e Metrologia (IQM), Rio de Janeiro, RJ (Brazil)], E-mail: gdoval.iqm@petrobras.com.br

    2009-07-01

    The measurement is considered as the 'cash register' of the enterprises, increasing the accuracy and the exigence at each step when come close to the delivery points, where the 0.1 % of differences are discussed. The work presents the approach used in the evaluation of measurement uncertainties in the volumes obtained of petroleum and natural gas at the processes of production in Brazil, and in the international level as well.

  9. Equations of bark thickness and volume profiles at different heights with easy-measurement variables

    Energy Technology Data Exchange (ETDEWEB)

    Cellini, J. M.; Galarza, M.; Burns, S. L.; Martinez-Pastur, G. J.; Lencinas, M. V.

    2012-11-01

    The objective of this work was to develop equations of thickness profile and bark volume at different heights with easy-measurement variables, taking as a study case Nothofagus pumilio forests, growing in different site qualities and growth phases in Southern Patagonia. Data was collected from 717 harvested trees. Three models were fitted using multiple, non-lineal regression and generalized linear model, by stepwise methodology, iteratively reweighted least squares method for maximum likelihood estimation and Marquardt algorithm. The dependent variables were diameter at 1.30 m height (DBH), relative height (RH) and growth phase (GP). The statistic evaluation was made through the adjusted determinant coefficient (r2-adj), standard error of the estimation (SEE), mean absolute error and residual analysis. All models presented good fitness with a significant correlation with the growth phase. A decrease in the thickness was observed when the relative height increase. Moreover, a bark coefficient was made to calculate volume with and without bark of individual trees, where significant differences according to site quality of the stands and DBH class of the trees were observed. It can be concluded that the prediction of bark thickness and bark coefficient is possible using DBH, height, site quality and growth phase, common and easy measurement variables used in forest inventories. (Author) 23 refs.

  10. Simulation method for cardiac stroke volume estimation by intracardiac electrical impedance measurement.

    Science.gov (United States)

    Barak, C; Leviatan, Y; Inbar, G F; Hoekstein, K N

    1992-09-01

    Using the electrical impedance measurement technique to investigate stroke volume estimation, three models of the ventricle were simulated. A four-electrode impedance catheter was used; two electrodes to set up an electric field in the model and the other two to measure the potential difference. A new approach, itself an application of the quasi-static case of a method used to solve electromagnetic field problems, was used to solve the electric field in the model. The behaviour of the estimation is examined with respect to the electrode configuration on the catheter and to catheter location with respect to the ventricle walls. Cardiac stroke volume estimation was found to be robust to catheter location generating a 10 per cent error for an offset of 40 per cent of the catheter from the chamber axis and rotation of 20 degrees with respect to the axis. The electrode configuration has a dominant effect on the sensitivity and accuracy of the estimation. Certain configurations gave high accuracy, whereas in others high sensitivity was found with lower accuracy. This led to the conclusion that the electrode configuration should be carefully chosen according to the desired criteria.

  11. Accurate measurement of volume and shape of resting and activated blood platelets from light scattering

    Science.gov (United States)

    Moskalensky, Alexander E.; Yurkin, Maxim A.; Konokhova, Anastasiya I.; Strokotov, Dmitry I.; Nekrasov, Vyacheslav M.; Chernyshev, Andrei V.; Tsvetovskaya, Galina A.; Chikova, Elena D.; Maltsev, Valeri P.

    2013-01-01

    We introduce a novel approach for determination of volume and shape of individual blood platelets modeled as an oblate spheroid from angle-resolved light scattering with flow-cytometric technique. The light-scattering profiles (LSPs) of individual platelets were measured with the scanning flow cytometer and the platelet characteristics were determined from the solution of the inverse light-scattering problem using the precomputed database of theoretical LSPs. We revealed a phenomenon of parameter compensation, which is partly explained in the framework of anomalous diffraction approximation. To overcome this problem, additional a priori information on the platelet refractive index was used. It allowed us to determine the size of each platelet with subdiffraction precision and independent of the particular value of the platelet aspect ratio. The shape (spheroidal aspect ratio) distributions of platelets showed substantial differences between native and activated by 10 μM adenosine diphosphate samples. We expect that the new approach may find use in hematological analyzers for accurate measurement of platelet volume distribution and for determination of the platelet activation efficiency.

  12. Accurate measurement of volume and shape of resting and activated blood platelets from light scattering.

    Science.gov (United States)

    Moskalensky, Alexander E; Yurkin, Maxim A; Konokhova, Anastasiya I; Strokotov, Dmitry I; Nekrasov, Vyacheslav M; Chernyshev, Andrei V; Tsvetovskaya, Galina A; Chikova, Elena D; Maltsev, Valeri P

    2013-01-01

    We introduce a novel approach for determination of volume and shape of individual blood platelets modeled as an oblate spheroid from angle-resolved light scattering with flow-cytometric technique. The light-scattering profiles (LSPs) of individual platelets were measured with the scanning flow cytometer and the platelet characteristics were determined from the solution of the inverse light-scattering problem using the precomputed database of theoretical LSPs. We revealed a phenomenon of parameter compensation, which is partly explained in the framework of anomalous diffraction approximation. To overcome this problem, additional a priori information on the platelet refractive index was used. It allowed us to determine the size of each platelet with subdiffraction precision and independent of the particular value of the platelet aspect ratio. The shape (spheroidal aspect ratio) distributions of platelets showed substantial differences between native and activated by 10 μM adenosine diphosphate samples. We expect that the new approach may find use in hematological analyzers for accurate measurement of platelet volume distribution and for determination of the platelet activation efficiency.

  13. The effects of renal variation upon measurements of perfusion and leakage volume in breast tumours

    Science.gov (United States)

    Ahearn, T. S.; Staff, R. T.; Redpath, T. W.; Semple, S. I. K.

    2004-05-01

    Dynamic contrast enhanced MRI (DCE-MRI) and pharmacokinetic models have been used to measure tumour permeability (Ktrans) and leakage volume (ve) in numerous studies. The construction of pharmacokinetic models describing such tissue properties relies on defining the blood plasma concentration of contrast agent with respect to time (Cp(t)). When direct measurement is not possible a bi-exponential decay has been applied using data from healthy volunteers. This work investigates, by simulation, the magnitude of errors resulting from this definition with respect to normal variation in renal function and for cases with renal impairment. Errors up to 23% in ve and 28% in Ktrans were found for the normal simulations, and 67% in ve and 61% in Ktrans for the impaired simulations. If this bi-exponential curve is used as an input function to the generalized kinetic model and used in oncology, estimates of tissue permeability and leakage volume will possess large errors due to variation in Cp(t) curves between subjects.

  14. Subject positioning in the BOD POD® only marginally affects measurement of body volume and estimation of percent body fat in young adult men.

    Directory of Open Access Journals (Sweden)

    Maarten W Peeters

    Full Text Available INTRODUCTION: The aim of the study was to evaluate whether subject positioning would affect the measurement of raw body volume, thoracic gas volume, corrected body volume and the resulting percent body fat as assessed by air displacement plethysmography (ADP. METHODS: Twenty-five young adult men (20.7±1.1 y, BMI = 22.5±1.4 kg/m(2 were measured using the BOD POD® system using a measured thoracic gas volume sitting in a 'forward bent' position and sitting up in a straight position in random order. RESULTS: Raw body volume was 58±124 ml (p<0.05 higher in the 'straight' position compared to the 'bent' position. The mean difference in measured thoracic gas volume (bent-straight = -71±211 ml was not statistically significant. Corrected body volume and percent body fat in the bent position consequently were on average 86±122 ml (p<0.05 and 0.5±0.7% (p<0.05 lower than in the straight position respectively. CONCLUSION: Although the differences reached statistical significance, absolute differences are rather small. Subject positioning should be viewed as a factor that may contribute to between-test variability and hence contribute to (inprecision in detecting small individual changes in body composition, rather than a potential source of systematic bias. It therefore may be advisable to pay attention to standardizing subject positioning when tracking small changes in PF are of interest. The cause of the differences is shown not to be related to changes in the volume of isothermal air in the lungs. It is hypothesized and calculated that the observed direction and magnitude of these differences may arise from the surface area artifact which does not take into account that a subject in the bent position exposes more skin to the air in the device therefore potentially creating a larger underestimation of the actual body volume due to the isothermal effect of air close to the skin.

  15. Measurement of Single Cell Refractive Index, Dry Mass, Volume, and Density Using a Transillumination Microscope

    Science.gov (United States)

    Phillips, Kevin G.; Jacques, Steven L.; McCarty, Owen J. T.

    2012-09-01

    Phase contrast microscopy has become ubiquitous in the field of biology, particularly in qualitative investigations of cellular morphology. However, the use of quantitative phase retrieval methods and their connection to cellular refractive index and dry mass density remain under utilized. This is due in part to the restriction of phase and cellular mass determination to custom built instruments, involved mathematical analysis, and prohibitive sample perturbations. We introduce tomographic bright field imaging, an accessible optical imaging technique enabling the three dimensional measurement of cellular refractive index and dry mass density using a standard transillumination optical microscope. The validity of the technique is demonstrated on polystyrene spheres. The technique is then applied to the measurement of the refractive index, dry mass, volume, and density of red blood cells. This optical technique enables a simple and robust means to perform quantitative investigations of engineered and biological specimens in three dimensions using standard optical microscopes.

  16. Measurement of slice thickness using partial volume effect in MR imaging

    Energy Technology Data Exchange (ETDEWEB)

    Higashida, Mitsuji; Yamazaki, Masaru [Osaka City Univ. (Japan). Hospital; Ogura, Akio; Inoue, Hiroshi; Hongou, Takaharu

    1998-08-01

    The NEMA standard and AAPM method have been approved for the determination of slice thickness in diagnostic magnetic resonance imaging. In these methods, the slice thickness is obtained as the full width at half maximum of the slice profile. However, these methods are affected by the signal-to-noise ratio (SNR) and pixel size. In addition, the measurement procedure required for accurate evaluation is troublesome. Therefore, a new method of evaluation using the partial volume effect, called the PVE method, is proposed. With the PVE method, slice thickness can be evaluated without the slice profile. A comparison of accuracy and simplicity of measurement is made between the PVE method and the wedge method of the NEMA standard. Results showed the PVE method to be accurate and easier to use than the wedge method. (author)

  17. OMERACT Rheumatoid Arthritis Magnetic Resonance Imaging Studies. Exercise 5: an international multicenter reliability study using computerized MRI erosion volume measurements

    DEFF Research Database (Denmark)

    Bird, P; Ejbjerg, B; McQueen, F;

    2003-01-01

    with metacarpophalangeal (MCP) joints 2 to 5 of the dominant hand included in the field of view. Three readers were instructed to grade MCP 2 and 3 using the OMERACT grading system and then to measure the erosion volume of the same joints using OSIRIS software. The inter-reader reliability of the grading method....... Good correlation was demonstrated between the total erosion scores and the total erosion volumes. For both erosion volumes and erosion scores, 1 mm and 3 mm acquisitions produced variable results between readers, with no clear pattern of underestimation or overestimation for either slice thickness....... The volume estimation method was more time consuming, taking roughly 5 times as long as the scoring method. Computerized MRI erosion volume measurements are feasible, with high intra-observer and inter-occasion reliabilities. Despite high ICC, the inter-observer reliability is not sufficient for multicenter...

  18. Temperature and relative density of atomic hydrogen in a multicusp H sup minus volume source

    Energy Technology Data Exchange (ETDEWEB)

    Bruneteau, A.M.; Hollos, G.; Bacal, M. (Laboratoire de Physique des Milieux Ionises, Laboratoire du Centre National de la Recherche Scientifique, Ecole Polytechnique, 91128 Palaiseau Cedex, (France)); Bretagne, J. (Laboratoire de Physique des Gaz et des Plasmas, LA73 du Centre National de la Recherche Scientifique, Universite de Paris-Sud, 91405 Orsay (France))

    1990-06-15

    The Balmer {beta} and {gamma} line shapes have been analyzed to determine the relative density and the temperature of hydrogen atoms in magnetic multicusp plasma generators. Results for a 90-V, 4--40-mTorr, 1--18-A conventional multicusp plasma generator and a 50-V, 4-mTorr, 1--15-A hybrid multicusp plasma generator are presented. The relative number density of hydrogen atoms increased smoothly with pressure and discharge current but never exceeded 10%. The absolute atomic number density in a 90-V 10-A discharge varied in proportion with pressure. The atomic temperature (in the 0.1--0.4-eV range) decreased with pressure and slowly increased with the discharge current. The role of atoms in the processes determining the H{sup {minus}} temperature and the H{sub 2} vibrational and rotational temperatures is discussed. The results confirm that in multicusp negative-ion sources collisional excitation of ground state atoms and molecules by energetic electrons is the dominant process in Balmer-{beta} and -{gamma} light emission.

  19. Atomic temperature and density in multicusp H sup minus volume sources

    Energy Technology Data Exchange (ETDEWEB)

    Bruneteau, A.M.; Hollos, G.; Leroy, R.; Berlemont, P.; Bacal, M. (Laboratoire du C.N.R.S., Ecole Polytechnique, 91128 Palaiseau Cedex (France)); Bertagne, J. (Laboratoire de Physique des Gaz et des Plasmas, LA73 du CNRS, Universite de Paris-Sud, 91405 Orsay (France))

    1990-08-05

    The Balmer {beta} and {gamma} line shapes have been analyzed to determine the relative density and the temperature of hydrogen atoms in magnetic multicusp plasma generators. Results for a 90 V, 4--40 mTorr, 1--18 A conventional multicusp plasma generator and a 50 V, 4 mTorr, 1--15 A hybrid multicusp plasma generator are presented. The relative number density of hydrogen atoms increases smoothly with pressure and discharge current but never exceeds 10%. The absolute atomic number density in a 90 V--10 A discharge varies in proportion with pressure. The atomic temperature (in the 0.1--0.4 eV range) decreases with pressure and slowly increases with the discharge current. The role of atoms in the processes determining the H{sup {minus}} temperature and the H{sub 2} vibrational and rotational temperatures is discussed. The results confirm that in multicusp negative ion sources collisional excitation of ground-state atoms and molecules by energetic electrons is the dominant process in Balmer {beta} and {gamma} light emission.

  20. LIGHT SOURCE: RF deflecting cavity for bunch length measurement in Tsinghua Thomson scattering X-ray source

    Science.gov (United States)

    Shi, Jia-Ru; Chen, Huai-Bi; Tang, Chuan-Xiang; Huang, Wen-Hui; Du, Ying-Chao; Zheng, Shu-Xin; Ren, Li

    2009-06-01

    An RF deflecting cavity used for bunch length measurement has been designed and fabricated at Tsinghua University for the Thomson Scattering X-Ray Source. The cavity is a 2856 MHz, π-mode, 3-cell standing-wave cavity, to diagnose the 3.5 MeV beam produced by photocathode electron gun. With a larger power source, the same cavity will again be used to measure the accelerated beam with energy of 50 MeV before colliding with the laser pulse. The RF design using MAFIA for both the cavity shape and the power coupler is reviewed, followed by presenting the fabrication procedure and bench measurement results of two cavities.

  1. A transient method for measuring the gas volume fraction in a mixed gas-liquid flow using acoustic resonance spectroscopy

    Institute of Scientific and Technical Information of China (English)

    2010-01-01

    In this paper, the feasibility of measuring the gas volume fraction in a mixed gas-liquid flow by using an acoustic resonant spectroscopy (ARS) method in a transient way is studied theoretically and experimentally. Firstly, the effects of sizes and locations of a single air bubble in a cylindrical cavity with two open ends on resonant frequencies are investigated numerically. Then, a transient measurement system for ARS is established, and the trends of the resonant frequencies (RFs) and resonant amplitudes (RAs) in the cylindrical cavity with gas flux inside are investigated experimentally. The measurement results by the proposed transient method are compared with those by steady-state ones and numerical ones. The numerical results show that the RFs of the cavity are highly sensitive to the volume of the single air bubble. A tiny bubble volume perturbation may cause a prominent RF shift even though the volume of the air bubble is smaller than 0.1% of that of the cavity. When the small air bubble moves, the RF shift will change and reach its maximum value as it is located at the middle of the cavity. As the gas volume fraction of the two-phase flow is low, both the RFs and RAs from the measurement results decrease dramatically with the increasing gas volume, and this decreasing trend gradually becomes even as the gas volume fraction increases further. These experimental results agree with the theoretical ones qualitatively. In addition, the transient method for ARS is more suitable for measuring the gas volume fraction with randomness and instantaneity than the steady-state one, because the latter could not reflect the random and instant characteristics of the mixed fluid due to the time consumption for frequency sweeping. This study will play a very important role in the quantitative measurement of the gas volume fraction of multiphase flows.

  2. Anatomic guidelines defined by reformatting images on MRI for volume measurement of amygdala and hippocampus

    Energy Technology Data Exchange (ETDEWEB)

    Hoshida, Tohru; Sakaki, Toshisuke [Nara Medical Univ., Kashihara (Japan); Uematsu, Sumio

    1995-03-01

    Twelve patients with intractable partial epilepsy underwent MR scans at the Epilepsy Center of the Johns Hopkins Hospital. There were five women and seven men, ranging in age from five to 51 years (mean age: 26 years). Coronal images were obtained using a 3-D SPGR. The coronal images were transferred to an Allegro 5.1 workstation, and reformatted along the cardinal axes (axial and sagittal) in multiple view points. The anterior end of the amygdala was measured at the level just posterior to the disappearance of the temporal stem. The semilunar gyrus of the amygdala was separated from the ambient gyrus by the semianular sulcus that forms the boundary between the amygdala and the entorhinal cortex. The delineation of the hippocampal formation included the subicular complex, hippocampal proper, dentate gyrus, alveus, and fimbria. The uncal cleft separated the uncus above from the parahippocampal gyrus below. The roof of this cleft was formed by the hippocampus and the dentate gyrus, and the floor, by the presubiculum and subiculum. Although using some guidelines, strictly separating the hippocampal head from the posterior part of the amygdala was not feasible as was previously reported, because of the isointensity on MRI between the cortex of the amygdala and the hippocampus. The most posterior portion of the hippocampus was measured at the level of the subsplenial gyri, just below the splenium of the corpus callosum, to measure the hippocampal volume in its near totality. Therefore, it is reliable, and clinically useful, to measure the combined total volume of the amygdala and the hippocampus when comparing results with those of other centers. (S.Y.).

  3. Accuracy and Consistency of Respiratory Inductive Plethysmography for Overnight Tidal Volume Measurement

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    To validate the accuracy and consistency of respiratory inductive plethysmography (RIP) in measuring tidal volume after an overnight sleep, tidal volumes of 18 patients with suspected sleep-disordered breathing and 8 normal volunteers were measured simultaneously with RIP (VTRIP) and with an ultrasonic airflow meter (VTUFM) before and after an unstrained overnight sleep on supine and lateral decubitus. The bias of the VTRIP was expressed as (VTRIP-VTUFM)/ VTUFM*100 %, limits of agreement between VTRIP and VTUFM was measured by averaged bias ±2 s. Results showed that in normal subjects, the bias of RIP before and after overnight sleep was precise and consistent in both supine (0.7 % and -1.6 %) and lateral decubitus (3.7 % and -0.56 %). In these patients, the bias of RIP before and after sleep in supine also remained small (1.9 % and 1.7 %), but it became larger in lateral decubitus (24.5 % and 20.4 %) and 11.5 % exceeded the limits of agreement observed in the evening. The patients′ body mass indices (BMI) were higher than those of normal subjects (median 34.2 vs. 27.8 kg/m2). Pooled data showed that the bias of VTRIP in the morning on lateral decubitus but not on supine was correlated to BMI (Spearman R=0.32, n=52, P=0.02). Thus, we were led to conclude that the accuracy of VTRIP overnight was precise and consistent in normal subjects, but the deviation of VTRIP measured on lateral decubitus in patients especially in those with excessive obesity was greater, thus, the method should not be used for quantitative determination.

  4. Limitations and pitfalls in measurements of right ventricular stroke volume in an animal model of right heart failure.

    Science.gov (United States)

    Vildbrad, Mads Dam; Andersen, Asger; Andersen, Thomas Krarup; Axelgaard, Sofie; Holmboe, Sarah; Andersen, Stine; Ringgaard, Steffen; Nielsen-Kudsk, Jens Erik

    2015-05-01

    Right heart failure occurs in various heart and pulmonary vascular diseases and may be fatal. We aimed to identify limitations in non-invasive measurements of right ventricular stroke volume in an animal model of right ventricular failure. Data from previous studies randomising rats to pulmonary trunk banding (PTB, n = 33) causing pressure-overload right ventricular failure or sham operation (n = 16) was evaluated retrospectively. We measured right ventricular stroke volume by high frequency echocardiography and magnetic resonance imaging (MRI). We found correlation between right ventricular stroke volume measured by echocardiography and MRI in the sham animals (r = 0.677, p = 0.004) but not in the PTB group. Echocardiography overestimated the stroke volume compared to MRI in both groups. Intra- and inter-observer variation did not explain the difference. Technical, physiological and anatomical issues in the pulmonary artery might explain why echocardiography over-estimates stroke volume. Flow acceleration close to the pulmonary artery banding can cause uncertainties in the PTB model and might explain the lack of correlation. In conclusion, we found a correlation in right ventricular stroke volume measured by echocardiography versus MRI in the sham group but not the PTB group. Echocardiography overestimated right ventricular stroke volume compared to MRI.

  5. A test method for the measurement of arylamines in stationary source emissions

    Energy Technology Data Exchange (ETDEWEB)

    Peterson, M.R.; Pate, B.A.; Wright, R.S. [Research Triangle Institute, Research Triangle Park, NC (United States)] [and others

    1996-12-31

    Title III of the Clean Air Act Amendments of 1990 lists eighteen arylamines as hazardous air pollutants to be regulated. The eighteen arylamines range from semivolatile to almost nonvolatile, from almost water-insoluble to hygroscopic, from thermally quite stable to unstable, and from fairly toxic to confirmed human carcinogens. This paper presents a report on progress in the development of a method to measure this quite disparate group of compounds in stationary source emissions. The proposed method involves collection in an acidic aqueous solution, sorption of collected arylamines on a cation exchange resin, desorption of arylamines from the resin with a small volume of a basic solution, and separation and measurement by high pressure liquid chromatography with photodiode array (HPLC-PDA) detection. Evaluation of cation exchange resins and resin elution solvents and the analytical portions of the method are being conducted using a subset of eight arylamines: aniline, chloramben, 2,4-diaminotoluene, N,N-dimethylaniline, 3,3`-dimethylbenzidine, quinoline, o-toluidine, and trifluralin. Sorption on a solid-phase extraction resin (LC-SCX, Supelco) followed by elution off the resin with a 2.2 normal solution of ammonia in a 50:35:15 mixture of 1-butanol, 1-propanol, and water gave the best recoveries of the test compounds (except chloramben, which contains a carboxylic acid group and does not elute) from the acidified collection solution. The compounds were separated on an Alltech Alltima C18 5{mu}m, 150 {times} 4.6 mm HPLC column using solvent programming with acetonitrile and either water or an acetate/acetic acid pH 7 buffer. 1 fig., 3 tabs.

  6. In situ calibrated defocusing PTV for wall-bounded measurement volumes

    Science.gov (United States)

    Fuchs, T.; Hain, R.; Kähler, C. J.

    2016-08-01

    In many situations, 3D velocity measurements in thin (∼1 mm) but wide (∼100  ×  100 mm2) flow channels is an important task. To resolve the in-plane and out-of-plane velocity gradients properly, a precise calibration is required, since 3D measurement approaches rely strongly on the accuracy of the calibration procedure. It is likely that calibration targets do not fit domains with small depths, due to their size. Furthermore, in fields where such measurements are of interest, the accessibility of the measurement volume is often limited or even impossible. To overcome these drawbacks, this paper introduces an in situ calibrated defocusing particle tracking velocimetry approach for wall-bounded measurement domains with depths in the low millimeter range. The calibration function for the particle depth location is directly derived from the particle image geometries and their displacements between two frames. Employing only a single camera, this defocusing approach is capable of measuring the air flow between two parallel glass plates at a distance of 1 mm with an average uncertainty of 2.43% for each track, relative to the maximum velocity. A tomographic particle tracking velocimetry measurement, serving as a benchmark for the single camera technique, reaches an average uncertainty of 1.59%. Altogether, with its straightforward set-up and without requiring a calibration target, this in situ calibrated defocusing approach opens new areas of application for optical flow velocimetry. In particular, for measurement domains with small optical windows and a lack of accessibility.

  7. VUV emission spectroscopy combined with H− density measurements in the ion source Prometheus I

    OpenAIRE

    Aleiferis, S.; Laulainen, Janne; Svarnas, P.; Tarvainen, Olli; Bacal, M.; Béchu, S.

    2017-01-01

    “Prometheus I” is a volume H− negative ion source, driven by a network of dipolar electron cyclotron resonance (ECR; 2.45 GHz) modules. The vacuum-ultraviolet (VUV) emission spectrum of low-temperature hydrogen plasmas may be related to molecular and atomic processes involved directly or indirectly in the production of negative ions. In this work, VUV spectroscopy has been performed in the above source, Prometheus I, both in the ECR zones and the bulk (far from ECR zones and surfaces) plasma....

  8. Advanced NSCLC First Pass Perfusion at 64-slice CT: Reproducibility of Volume-based Quantitative Measurement

    Directory of Open Access Journals (Sweden)

    Jie HU

    2010-05-01

    Full Text Available Background and objective The aim of this study is to explore the reproducibility of volume-based quantitative measurement of non-small cell lung cancer (NSCLC perfusion at 64-slice CT. Methods Fourteen patients with proved advanced NSCLC were enrolled in this dynamic first pass volume-based CT perfusion (CTP study (8×5 mm collimation, and they underwent the second scan within 24 h. According to the longest diameters, those patients were classified to ≤3 cm and >3 cm groups, and each group had 7 patients. Intraclass correlation coefficient (ICC and Bland-Altman statistics were used to evaluate the reproducibility of CTP imaging. Results In both groups of advanced NSCLC, the reproducibility with BF, BV, and PS values were good (ICC >0.75 for all, but mean transit time (MTT values. For advanced NSCLC (≤3 cm, repeatability coefficient (RC values with blood flow (BF, blood volume (BV, MTT and permeability surface area product (PS values were 56%, 45%, 114%, and 78%, respectively, and the 95% change intervals of RC were -39%-53%, -29%-62%, -83%-145%, and -57%-98%, respectively. For advanced NSCLC (>3 cm, those values were 46%, 30%, 59%, and 33%, respectively, and the 95% change intervals of RC were -48%-45%, -33%-26%, -54%-64%, and -18%-48%. Conclusion There is greater reproducibility of tumor size >3 cm than that of ≤3 cm. BF and BV could be addressed for reliable clinical application in antiangiogenesis therapeutic monitoring with advanced NSCLC patients.

  9. Dyslexia and voxel-based morphometry: correlations between five behavioural measures of dyslexia and gray and white matter volumes.

    Science.gov (United States)

    Tamboer, Peter; Scholte, H Steven; Vorst, Harrie C M

    2015-10-01

    In voxel-based morphometry studies of dyslexia, the relation between causal theories of dyslexia and gray matter (GM) and white matter (WM) volume alterations is still under debate. Some alterations are consistently reported, but others failed to reach significance. We investigated GM alterations in a large sample of Dutch students (37 dyslexics and 57 non-dyslexics) with two analyses: group differences in local GM and total GM and WM volume and correlations between GM and WM volumes and five behavioural measures. We found no significant group differences after corrections for multiple comparisons although total WM volume was lower in the group of dyslexics when age was partialled out. We presented an overview of uncorrected clusters of voxels (p  200) with reduced or increased GM volume. We found four significant correlations between factors of dyslexia representing various behavioural measures and the clusters found in the first analysis. In the whole sample, a factor related to performances in spelling correlated negatively with GM volume in the left posterior cerebellum. Within the group of dyslexics, a factor related to performances in Dutch-English rhyme words correlated positively with GM volume in the left and right caudate nucleus and negatively with increased total WM volume. Most of our findings were in accordance with previous reports. A relatively new finding was the involvement of the caudate nucleus. We confirmed the multiple cognitive nature of dyslexia and suggested that experience greatly influences anatomical alterations depending on various subtypes of dyslexia, especially in a student sample.

  10. Comparison of vertebral artery velocity and flow volume measurements for diagnosis of vertebrobasilar insufficiency using color duplex sonography

    Energy Technology Data Exchange (ETDEWEB)

    Acar, Murat [Department of Radiology, Faculty of Medicine, Afyon Kocatepe University, Kirmizi Hastane, 03200 Afyon (Turkey)]. E-mail: drmacar@hotmail.com; Degirmenci, Bumin [Department of Radiology, Faculty of Medicine, Afyon Kocatepe University, Kirmizi Hastane, 03200 Afyon (Turkey); Yucel, Aylin [Department of Radiology, Faculty of Medicine, Afyon Kocatepe University, Kirmizi Hastane, 03200 Afyon (Turkey); Albayrak, Ramazan [Department of Radiology, Faculty of Medicine, Afyon Kocatepe University, Kirmizi Hastane, 03200 Afyon (Turkey); Haktanir, Alpay [Department of Radiology, Faculty of Medicine, Afyon Kocatepe University, Kirmizi Hastane, 03200 Afyon (Turkey); Yaman, Mehmet [Department of Neurology, Faculty of Medicine, Afyon Kocatepe University, 03200 Afyon (Turkey)

    2005-05-01

    Introduction: The aim of this study was to compare the measurements of vertebral artery (VA) systolic flow velocity and flow volume for diagnosis of vertebrobasilar insufficiency (VBI). Material and methods: We examined 96 patients who were referred for evaluation of VBI. Net vertebral artery flow volume and mean systolic flow velocity were determined by using color duplex sonography. We had grouped the patients into three according to VA flow volume: group 1 was consisted of patients with severely damped VA flow volume (lower than 120 mL/min), group 2 was consisted of patients with moderately damped VA flow volume (120-200 mL/min), group 3 was consisted of patients with normal VA flow volume (>200 mL/min). The mean systolic flow velocities in each group were compared by one-way ANOVA. Results: Mean VA systolic flow velocities of groups 1, 2 and 3 were 32 {+-} 12, 42 {+-} 10 and 46 {+-} 8 cm/s, respectively. Mean VA systolic flow velocity in group 1 was significantly lower than that of group 2 (P = 0.001). However, there were no significant differences between VA systolic flow velocities in groups 2 and 3 (P = 0.2). Conclusions: According to our findings, measurement of volume in addition to velocity is more valuable in detection of moderately damped VA flow volumes in diagnosis of VBI.

  11. Evaluation of severe accident risks: Methodology for the containment, source term, consequence, and risk integration analyses; Volume 1, Revision 1

    Energy Technology Data Exchange (ETDEWEB)

    Gorham, E.D.; Breeding, R.J.; Brown, T.D.; Harper, F.T. [Sandia National Labs., Albuquerque, NM (United States); Helton, J.C. [Arizona State Univ., Tempe, AZ (United States); Murfin, W.B. [Technadyne Engineering Consultants, Inc., Albuquerque, NM (United States); Hora, S.C. [Hawaii Univ., Hilo, HI (United States)

    1993-12-01

    NUREG-1150 examines the risk to the public from five nuclear power plants. The NUREG-1150 plant studies are Level III probabilistic risk assessments (PRAs) and, as such, they consist of four analysis components: accident frequency analysis, accident progression analysis, source term analysis, and consequence analysis. This volume summarizes the methods utilized in performing the last three components and the assembly of these analyses into an overall risk assessment. The NUREG-1150 analysis approach is based on the following ideas: (1) general and relatively fast-running models for the individual analysis components, (2) well-defined interfaces between the individual analysis components, (3) use of Monte Carlo techniques together with an efficient sampling procedure to propagate uncertainties, (4) use of expert panels to develop distributions for important phenomenological issues, and (5) automation of the overall analysis. Many features of the new analysis procedures were adopted to facilitate a comprehensive treatment of uncertainty in the complete risk analysis. Uncertainties in the accident frequency, accident progression and source term analyses were included in the overall uncertainty assessment. The uncertainties in the consequence analysis were not included in this assessment. A large effort was devoted to the development of procedures for obtaining expert opinion and the execution of these procedures to quantify parameters and phenomena for which there is large uncertainty and divergent opinions in the reactor safety community.

  12. Prognostic value of epicardial fat volume measurements by computed tomography: a systematic review of the literature

    Energy Technology Data Exchange (ETDEWEB)

    Spearman, James V.; Krazinski, Aleksander W. [Medical University of South Carolina, Department of Radiology and Radiological Science, Charleston, SC (United States); Renker, Matthias [Medical University of South Carolina, Department of Radiology and Radiological Science, Charleston, SC (United States); Giessen University, Department of Internal Medicine I, Cardiology/Angiology, Giessen (Germany); Schoepf, U.J. [Medical University of South Carolina, Department of Radiology and Radiological Science, Charleston, SC (United States); Medical University of South Carolina, Division of Cardiology, Department of Medicine, Charleston, SC (United States); Herbert, Teri L. [Medical University of South Carolina, Department of Library Science and Informatics, Charleston, SC (United States); De Cecco, Carlo N. [Medical University of South Carolina, Department of Radiology and Radiological Science, Charleston, SC (United States); University of Rome ' Sapienza' - Polo Pontino, Department of Radiological Sciences, Oncology and Pathology, Latina (Italy); Nietert, Paul J. [Medical University of South Carolina, Department of Public Health Sciences, Charleston, SC (United States); Meinel, Felix G. [Medical University of South Carolina, Department of Radiology and Radiological Science, Charleston, SC (United States); Ludwig-Maximilians-University Hospital, Institute for Clinical Radiology, Munich (Germany)

    2015-11-15

    To perform a systematic review of the growing body of literature evaluating the prognostic value of epicardial fat volume (EFV) quantified by cross-sectional imaging. Two independent reviewers performed systematic searches on both PubMed and Scopus using search terms developed with a medical librarian. Peer-reviewed articles were selected based on the inclusion of outcome data, utilization of epicardial fat volume and sufficient reporting for analysis. A total of 411 studies were evaluated with nine studies meeting the inclusion criteria. In all, the studies evaluated 10,252 patients. All nine studies were based on CT measurements. Seven studies evaluated the prognostic value of EFV unadjusted for calcium score, and six of these studies found a significant association between EFV and clinical outcomes. Seven studies evaluated the incremental value of EFV beyond calcium scoring, and six of these studies found a significant association. The majority of studies suggest that EFV quantification is significantly associated with clinical outcomes and provides incremental prognostic value over coronary artery calcium scoring. Future research should use a binary cutoff of 125 mL for evaluation of EFV to provide consistency with other research. (orig.)

  13. Large range rotation distortion measurement for remote sensing images based on volume holographic optical correlator

    Science.gov (United States)

    Zheng, Tianxiang; Cao, Liangcai; Zhao, Tian; He, Qingsheng; Jin, Guofan

    2012-10-01

    Volume holographic optical correlator can compute the correlation results between images at a super-high speed. In the application of remote imaging processing such as scene matching, 6,000 template images have been angularly multiplexed in the photorefractive crystal and the 6,000 parallel processing channels are achieved. In order to detect the correlation pattern of images precisely and distinguishingly, an on-off pixel inverted technology of images is proposed. It can fully use the CCD's linear range for detection and expand the normalized correlation value differences as the target image rotates. Due to the natural characteristics of the remote sensing images, the statistical formulas between the rotation distortions and the correlation results can be estimated. The rotation distortion components can be estimated by curve fitting method with the data of correlation results. The intensities of the correlation spots are related to the distortion between the two images. The rotation distortion could be derived from the intensities in the post processing procedure. With 18 rotations of the input image and sending them into the volume holographic system, the detection of the rotation variation in the range of 180° can be fulfilled. So the large range rotation distortion detection is firstly realized. It offers a fast, large range rotation measurement method for image distortions.

  14. Quantitative measurements of cerebral blood flow in volume imaging PET scanners

    Energy Technology Data Exchange (ETDEWEB)

    Smith, R.J.; Shao, L.; Freifelder, R.; Karp, J.S.; Ragland, J.D. [Univ. of Pennsylvania, Philadelphia, PA (United States)

    1995-08-01

    Quantitative measurements of Cerebral Blood Flow (CBF) are performed in a volume imaging PET Scanner by means of moderate activity infusions. In equilibrium infusions, activations are measured by scanning over 10 minutes with 16 minute activations. Typical measured whole brain CBF values are 37{+-}8 ml/min/100g, close to the value of 42 ml/min/100g reported by other groups using this method. For ramped infusions, scanning over 4 minutes with 5 minute activations results in whole brain CBFs of 49 {+-} 9 ml/min/100g, close to the Kety and Schmidt value of 50 ml/min/100g. Both equilibrium and ramped infusion methods have been used to study face and word memory in human subjects. Both methods were able to detect significant activations in regions implicated in human memory. The authors conclude that precise quantitation of regional CBF is achieved using both methods, and that ramped infusions also provide accurate measures of CBF. In addition a simplified protocol for ramped infusion studies has been developed. In this method the whole brain tissue time activity curve generated from dynamic scanning is replaced by an appropriately scaled camera coincidence countrate curve. The resulting whole brain CBF values are only 7% different from the dynamic scan and fit results. Regional CBFs (rCBF) may then be generated from the summed image (4.25 minutes) using a count density vs flow lookup table.

  15. Tumor-to-breast volume ratio as measured on MRI: a possible predictor of breast-conserving surgery versus mastectomy.

    Science.gov (United States)

    Faermann, Renata; Sperber, Fani; Schneebaum, Schlomo; Barsuk, Daphna

    2014-02-01

    The surgical approach to breast cancer changed dramatically in the past 20 years. The surgical objective today is to remove the tumor, ensuring negative margins and good cosmetic results, and preserving the breast when possible. Magnetic resonance imaging of the breast has become an essential imaging tool prior to surgery, diagnosing additional tumors and assessing tumor extent. Tumor-to-breast volume ratio, an important predictor of breast conservation, can be measured with MRI and may change the surgical decision. To measure the tumor-to-breast volume ratio using MRI in order to assess whether there is a correlation between this ratio and the type of surgery selected (breast-conserving or mastectomy). The volumes of the tumor and the breast and the tumor-to-breast volume ratio were retrospectively calculated using preoperative breast MRI in 76 patients who underwent breast-conserving surgery or mastectomy. Breast-conserving surgery (lumpectomy) was performed in 64 patients and mastectomy in 12. The average tumor-to-breast volume ratio was 0.06 (6%) in the lumpectomy group and 0.30 (30%) in the mastectomy group (P < 0.0001). The tumor-to-breast volume ratio correlated with the type of surgery. As measured on MRI, this ratio is an accurate means of determining the type of surgery best suited for a given patient. It is recommended that MRI-determined tumor-to-breast volume ratio become part of the surgical planning protocol for patients diagnosed with breast cancer.

  16. Comparison of volume and diameter measurement in assessing small abdominal aortic aneurysm expansion examined using computed tomographic angiography

    Energy Technology Data Exchange (ETDEWEB)

    Parr, Adam; Jayaratne, Chanaka; Buttner, Petra [Vascular Biology Unit, James Cook University, Townsville, Queensland 4811 (Australia); Golledge, Jonathan, E-mail: Jonathan.Golledge@jcu.edu.au [Vascular Biology Unit, James Cook University, Townsville, Queensland 4811 (Australia)

    2011-07-15

    Aim: First we aimed to assess the reproducibility of a computer tomography angiography (CTA) based technique for measuring infra-renal aortic volume and diameter. Second we sought to investigate whether changes in aortic volume and diameter were similar during follow-up. Materials and methods: A prospective series of 57 patients, with aortic diameter initially measuring between 25 and 55 mm, were assessed with 2 CTAs a median of 14 months apart. Aortic volume and maximum diameter (both axial and orthogonal) were measured by a semi-automated workstation protocol based on previously defined techniques. Intra- and inter-observer reproducibility were assessed by repeat assessment of the initial CTA images of the first 33 patients included in the study, in order to estimate the 95% limits of agreements. Changes in aortic dimensions between the first and follow-up CTA, were defined for volume and diameter separately as changes greater than their respective 95% limits of agreement. Results: Reproducibility of aortic volume and diameter was excellent with an average coefficient of variation <4%. The median (inter-quartile range) increases in total volume, orthogonal and axial diameters were 4.9 cm{sup 3} (0.01-14.18), 1.2 mm (0.40-3.50) and 1.4 mm (-0.15 to 3.55) respectively. Forty-two percent of patients who had increased aortic volume above the 95% limit of agreement did not display corresponding axial or orthogonal diameter changes. Conclusions: Infra-renal total aortic volume, axial and orthogonal diameter can all be measured reproducibly from CTA. Aortic volume changes are not always reflected by similar changes in diameter and therefore provide complementary information when assessing AAA expansion over time.

  17. Blind source separation of internal combustion engine piston slap from other measured vibration signals

    Science.gov (United States)

    Liu, Xianhua; Randall, R. B.

    2005-11-01

    Internal combustion engines have several vibration sources, such as combustion, fuel injection, piston slap and valve operation. For machine condition monitoring or design improvement purposes, it is necessary to separate the vibration signals caused by different sources and then analyse each of them individually. However, traditional frequency analysis techniques are not very useful due to overlap of the different sources over a wide frequency range. This paper attempts to separate the vibration sources, especially piston slap, by using blind source separation techniques with the intention of revealing the potential of the new technique for solving mechanical vibration problems. The BSS method and the Blind least mean square algorithm using Gray's variable norm as a measure of non-Gaussianity of the sources is briefly described and separation results for both simulated and measured data are presented and discussed.

  18. Gas permeation measurement under defined humidity via constant volume/variable pressure method

    KAUST Repository

    Jan Roman, Pauls

    2012-02-01

    Many industrial gas separations in which membrane processes are feasible entail high water vapour contents, as in CO 2-separation from flue gas in carbon capture and storage (CCS), or in biogas/natural gas processing. Studying the effect of water vapour on gas permeability through polymeric membranes is essential for materials design and optimization of these membrane applications. In particular, for amine-based CO 2 selective facilitated transport membranes, water vapour is necessary for carrier-complex formation (Matsuyama et al., 1996; Deng and Hägg, 2010; Liu et al., 2008; Shishatskiy et al., 2010) [1-4]. But also conventional polymeric membrane materials can vary their permeation behaviour due to water-induced swelling (Potreck, 2009) [5]. Here we describe a simple approach to gas permeability measurement in the presence of water vapour, in the form of a modified constant volume/variable pressure method (pressure increase method). © 2011 Elsevier B.V.

  19. Measuring the mode volume of plasmonic nanocavities using coupled optical emitters

    CERN Document Server

    Russell, Kasey J; Hu, Evelyn; 10.1103/PhysRevB.85.245445

    2012-01-01

    Metallic optical systems can confine light to deep sub-wavelength dimensions, but verifying the level of confinement at these length scales typically requires specialized techniques and equipment for probing the near-field of the structure. We experimentally measured the confinement of a metal-based optical cavity by using the cavity modes themselves as a sensitive probe of the cavity characteristics. By perturbing the cavity modes with conformal dielectric layers of sub-nm thickness using atomic layer deposition, we find the exponential decay length of the modes to be less than 5% of the free-space wavelength (\\lambda) and the mode volume to be of order \\lambda^3/1000. These results provide experimental confirmation of the deep sub-wavelength confinement capabilities of metal-based optical cavities.

  20. A measurement-based generalized source model for Monte Carlo dose simulations of CT scans

    Science.gov (United States)

    Ming, Xin; Feng, Yuanming; Liu, Ransheng; Yang, Chengwen; Zhou, Li; Zhai, Hezheng; Deng, Jun

    2017-03-01

    The goal of this study is to develop a generalized source model for accurate Monte Carlo dose simulations of CT scans based solely on the measurement data without a priori knowledge of scanner specifications. The proposed generalized source model consists of an extended circular source located at x-ray target level with its energy spectrum, source distribution and fluence distribution derived from a set of measurement data conveniently available in the clinic. Specifically, the central axis percent depth dose (PDD) curves measured in water and the cone output factors measured in air were used to derive the energy spectrum and the source distribution respectively with a Levenberg–Marquardt algorithm. The in-air film measurement of fan-beam dose profiles at fixed gantry was back-projected to generate the fluence distribution of the source model. A benchmarked Monte Carlo user code was used to simulate the dose distributions in water with the developed source model as beam input. The feasibility and accuracy of the proposed source model was tested on a GE LightSpeed and a Philips Brilliance Big Bore multi-detector CT (MDCT) scanners available in our clinic. In general, the Monte Carlo simulations of the PDDs in water and dose profiles along lateral and longitudinal directions agreed with the measurements within 4%/1 mm for both CT scanners. The absolute dose comparison using two CTDI phantoms (16 cm and 32 cm in diameters) indicated a better than 5% agreement between the Monte Carlo-simulated and the ion chamber-measured doses at a variety of locations for the two scanners. Overall, this study demonstrated that a generalized source model can be constructed based only on a set of measurement data and used for accurate Monte Carlo dose simulations of patients’ CT scans, which would facilitate patient-specific CT organ dose estimation and cancer risk management in the diagnostic and therapeutic radiology.

  1. Measurement of an image jitter of an extended incoherent radiation source

    Science.gov (United States)

    Lukin, V. P.; Nosov, V. V.

    2017-06-01

    A scheme of an image jitter measuring device, which uses an extended incoherent source as a radiation source, is presented. The efficiency of the measuring device is analysed analytically and numerically in order to justify the operation of the adaptive optical system that does not require special creation or formation of a reference source. The features of the formed image of incoherent radiation are considered, in particular from the point of view of its possible application for measuring the phase fluctuations of optical waves propagating in a turbulent atmosphere (the adaptive system monitors the image of a self-luminous object illuminated by extraneous sources). The possibility of utilising a Shack-Hartmann wavefront sensor in adaptive systems using the image of an arbitrary object (or its fragment) as a reference source is shown.

  2. First common volume measurements of PMSE and NLC layers above EISCAT, Tromsö

    Science.gov (United States)

    Dalin, Peter; Mann, Ingrid; Häggström, Ingemar

    2016-04-01

    Close to the mesopause in the atmosphere at medium to high latitudes ice particles form during the summer months. The ice particles are observed in noctilucent clouds (NLC) and cause the formation of specific radar echoes, Polar Mesospheric Summer Echoes (PMSE). While NLC and PMSE are both linked to the presence of ice particles and observed at similar overlapping altitudes, they are also influenced by other parameters, e.g. neutral atmospheric dynamics, turbulence and dusty plasma effects, and their exact formation conditions are still subject to investigations. We here present first results from a number of simultaneous observations of both phenomena. The "Mesoclouds" campaign was conducted between 8-20 August 2015 with the aim to investigate PMSE and NLC activity in the common volume of the atmosphere above the Tromsö EISCAT station. For simultaneous optical and radar measurements of NLC and PMSE layers we ran EISCAT VHF (224 MHz) and UHF (930 MHz) radars at Tromsö (Norway) as well as two optical NLC cameras located at Kiruna and Nikkaluokta (Sweden). Both locations of the NLC cameras are about 200 km south of Tromsö, which permits making NLC triangulation measurements. Three NLC/PMSE cases above Tromsö are discussed. The first case on 9-10 August displayed NLC and PMSE layers simultaneously above Tromsö. The second case on 12-13 August showed a partial coincidence of NLC and PMSE: NLC were observed in the evening and morning hours whereas PMSE were mostly seen in the morning hours. In the third case on 19-20 August no NLC were observed, while PMSE were observed in the morning hours. We present the observational data, investigate peculiar dynamical features intrinsic to PMSE and NLC layers in the common atmospheric volume and discuss its implications for observation of ice particles.

  3. Measurement-device-independent quantum key distribution with source state errors and statistical fluctuation

    Science.gov (United States)

    Jiang, Cong; Yu, Zong-Wen; Wang, Xiang-Bin

    2017-03-01

    We show how to calculate the secure final key rate in the four-intensity decoy-state measurement-device-independent quantum key distribution protocol with both source errors and statistical fluctuations with a certain failure probability. Our results rely only on the range of only a few parameters in the source state. All imperfections in this protocol have been taken into consideration without assuming any specific error patterns of the source.

  4. THE Q/U IMAGING EXPERIMENT: POLARIZATION MEASUREMENTS OF RADIO SOURCES AT 43 AND 95 GHz

    Energy Technology Data Exchange (ETDEWEB)

    Huffenberger, K. M. [Department of Physics, Florida State University, P.O. Box 3064350, Tallahassee, FL 32306-4350 (United States); Araujo, D.; Zwart, J. T. L. [Department of Physics and Columbia Astrophysics Laboratory, Columbia University, New York, NY 10027 (United States); Bischoff, C.; Buder, I. [Kavli Institute for Cosmological Physics, Department of Physics, Enrico Fermi Institute, The University of Chicago, Chicago, IL 60637 (United States); Chinone, Y.; Hasegawa, M. [High Energy Accelerator Research Organization (KEK), 1-1 Oho, Tsukuba, Ibaraki 305-0801 (Japan); Cleary, K. [Cahill Center for Astronomy and Astrophysics, California Institute of Technology, 1200 E. California Blvd M/C 249-17, Pasadena, CA 91125 (United States); Kusaka, A. [Physics Division, Lawrence Berkeley National Laboratory, 1 Cyclotron Road, Berkeley, CA 94720 (United States); Monsalve, R. [School of Earth and Space Exploration, Arizona State University, 781 E. Terrace Road, Tempe, AZ 85287 (United States); Næss, S. K. [Department of Astrophysics, University of Oxford, Keble Road, Oxford, OX1 3RH (United Kingdom); Newburgh, L. B. [Dunlap Institute, University of Toronto, 50 St. George Street, Toronto, ON M5S 3H4 (Canada); Reeves, R. [CePIA, Departamento de Astronomía, Universidad de Concepción (Chile); Ruud, T. M.; Eriksen, H. K. [Institute of Theoretical Astrophysics, University of Oslo, P.O. Box 1029 Blindern, NO-0315 Oslo (Norway); Wehus, I. K.; Gaier, T. [Jet Propulsion Laboratory, California Institute of Technology, 4800 Oak Grove Drive, Pasadena, CA 91109 (United States); Dickinson, C. [Jodrell Bank Centre for Astrophysics, Alan Turing Building, School of Physics and Astronomy, The University of Manchester, Oxford Road, Manchester M13 9PL (United Kingdom); Gundersen, J. O., E-mail: huffenbe@physics.fsu.edu [Department of Physics, University of Miami, 1320 Campo Sano Drive, Coral Gables, FL 33146 (United States); Collaboration: QUIET Collaboration; and others

    2015-06-10

    We present polarization measurements of extragalactic radio sources observed during the cosmic microwave background polarization survey of the Q/U Imaging Experiment (QUIET), operating at 43 GHz (Q-band) and 95 GHz (W-band). We examine sources selected at 20 GHz from the public, >40 mJy catalog of the Australia Telescope (AT20G) survey. There are ∼480 such sources within QUIET’s four low-foreground survey patches, including the nearby radio galaxies Centaurus A and Pictor A. The median error on our polarized flux density measurements is 30–40 mJy per Stokes parameter. At signal-to-noise ratio > 3 significance, we detect linear polarization for seven sources in Q-band and six in W-band; only 1.3 ± 1.1 detections per frequency band are expected by chance. For sources without a detection of polarized emission, we find that half of the sources have polarization amplitudes below 90 mJy (Q-band) and 106 mJy (W-band), at 95% confidence. Finally, we compare our polarization measurements to intensity and polarization measurements of the same sources from the literature. For the four sources with WMAP and Planck intensity measurements >1 Jy, the polarization fractions are above 1% in both QUIET bands. At high significance, we compute polarization fractions as much as 10%–20% for some sources, but the effects of source variability may cut that level in half for contemporaneous comparisons. Our results indicate that simple models—ones that scale a fixed polarization fraction with frequency—are inadequate to model the behavior of these sources and their contributions to polarization maps.

  5. Volumetric apparatus for hydrogen adsorption and diffusion measurements: sources of systematic error and impact of their experimental resolutions.

    Science.gov (United States)

    Policicchio, Alfonso; Maccallini, Enrico; Kalantzopoulos, Georgios N; Cataldi, Ugo; Abate, Salvatore; Desiderio, Giovanni; Agostino, Raffaele Giuseppe

    2013-10-01

    The development of a volumetric apparatus (also known as a Sieverts' apparatus) for accurate and reliable hydrogen adsorption measurement is shown. The instrument minimizes the sources of systematic errors which are mainly due to inner volume calibration, stability and uniformity of the temperatures, precise evaluation of the skeletal volume of the measured samples, and thermodynamical properties of the gas species. A series of hardware and software solutions were designed and introduced in the apparatus, which we will indicate as f-PcT, in order to deal with these aspects. The results are represented in terms of an accurate evaluation of the equilibrium and dynamical characteristics of the molecular hydrogen adsorption on two well-known porous media. The contribution of each experimental solution to the error propagation of the adsorbed moles is assessed. The developed volumetric apparatus for gas storage capacity measurements allows an accurate evaluation over a 4 order-of-magnitude pressure range (from 1 kPa to 8 MPa) and in temperatures ranging between 77 K and 470 K. The acquired results are in good agreement with the values reported in the literature.

  6. [Instrumentation for blood pressure measurements: historical aspects, concepts and sources of error].

    Science.gov (United States)

    de Araujo, T L; Arcuri, E A; Martins, E

    1998-04-01

    According to the International Council of Nurses the measurement of blood pressure is the procedure most performed by nurses in all the world. The aim of this study is to analyse the polemical aspects of instruments used in blood pressure measurement. Considering the analyses of the literature and the American Heart Association Recommendations, the main source of errors when measuring blood pressure are discussed.

  7. Small-scale structures in common-volume meteor wind measurements

    Science.gov (United States)

    Fraser, G. J.; Marsh, S. H.; Baggaley, W. J.; Bennett, R. G. T.; Lawrence, B. N.; McDonald, A. J.; Plank, G. E.

    2006-02-01

    Observational differences occur when different techniques are used for measuring mesospheric winds because the different instruments observe different physical quantities to infer the wind velocity, and have differing time and space resolution. The AMOR meteor wind radar near Christchurch, New Zealand [Marsh et al., 2000. Journal of Atmospheric and Solar-Terrestrial Physics 62,1129 1133.] has good resolution in time (˜0.1 s) and height (˜1 km) and a narrow beam centred in the geographic N S meridian. The meteor echoes randomly sample the atmosphere in a region extending over several hundred kilometres to the South of the radar. The volume of data obtained from the one instrument has made it possible to use correlations between measurements made from individual meteor trails to identify the contribution of atmospheric variability to the observational differences. Measurements of the meridional wind component made from May July 1997 inclusive show that a large part (20 30 m/s r.m.s.) of the atmospheric variation is due to inhomogeneities with small scales, of the order of 10 km and 1 h. There is also a component which has a random time phase over the observation interval but a spatial scale which is coherent over several hundred kilometres, consistent with the behaviour of gravity waves.

  8. Curling probe measurement of a large-volume pulsed plasma with surface magnetic confinement

    Science.gov (United States)

    Pandey, A.; Tashiro, H.; Sakakibara, W.; Nakamura, K.; Sugai, H.

    2016-12-01

    A curling probe (CP) based on microwave resonance is applied to the measurement of electron density in a pulsed DC glow discharge under surface magnetic confinement (SMC) provided by a number of permanent magnets on a chamber wall. Owing to the SMC effects, a 1 m scale large-volume plasma is generated by a relatively low voltage (~1 kV) at low pressure (~1 Pa) in various gases (Ar, CH4, and C2H2). Temporal variation of the electron density is measured for pulse frequency f  =  0.5-25 kHz for various discharge-on times (T ON) with a high resolution time (~0.2 µs), using the on-point mode. In general, the electron density starts to increase at time t  =  0 after turn-on of the discharge voltage, reaches peak density at t  =  T ON, and then decreases after turn-off. The peak electron density is observed to increase with the pulse frequency f for constant T ON owing to the residual plasma. This dependence is successfully formulated using a semi-empirical model. The spatio-temporal evolution of the cathode sheath in the pulsed discharge is revealed by a 1 m long movable CP. The measured thickness of the high-voltage cathode fall in a steady state coincides with the value of the so-called Child-Langmuir sheath.

  9. Volume Entropy

    CERN Document Server

    Astuti, Valerio; Rovelli, Carlo

    2016-01-01

    Building on a technical result by Brunnemann and Rideout on the spectrum of the Volume operator in Loop Quantum Gravity, we show that the dimension of the space of the quadrivalent states --with finite-volume individual nodes-- describing a region with total volume smaller than $V$, has \\emph{finite} dimension, bounded by $V \\log V$. This allows us to introduce the notion of "volume entropy": the von Neumann entropy associated to the measurement of volume.

  10. Measurement of the neutron spectrum of a Pu-C source with a liquid scintillator

    Institute of Scientific and Technical Information of China (English)

    WANG Song-Lin; HUANG Han-Xiong; RUAN Xi-Chao; LI Xia; BAO Jie; NIE Yang-So; ZHONG Qi-Ping; ZHOU Zu-Ying; KONG Xiang-Zhong

    2009-01-01

    The neutron response function for a BC501A liquid scintillator (LS) has been measured using a series of monoenergetic neutrons produced by the p-T reaction. The proton energies were chosen such as to produce neutrons in the energy range of 1 to 20 MeV. The principles of the technique of unfolding a neutron energy spectrum by using the measured neutron response function and the measured Pulse Height (PH) spectrum is briefly described. The PH spectrum of neutrons from the Pu-C source, which will be used for the calibration of the reactor antineutrino detectors for the Daya Bay neutrino experiment, was measured and analyzed to get the neutron energy spectrum. Simultaneously the neutron energy spectrum of an Am-Be source was measured and compared with other measurements as a check of the result for the Pu-C source. Finally, an error analysis and a discussion of the results are given.

  11. Impact of blood volume changes within the human skin on the diffuse reflectance measurements in visible and NIR spectral ranges

    Science.gov (United States)

    Zherebtsov, Evgeny; Bykov, Alexander; Popov, Alexey; Doronin, Alexander; Meglinski, Igor

    2017-03-01

    We consider changes in the volume of blood and oxygen saturation caused by a pulse wave and their influence on the diffuse reflectance spectra in the visible/NIR spectral range. CUDA-based Monte-Carlo model was used for routine simulation of detector depth sensitivity (sampling volume) and skin spectra, and their variations associated with physiological changes in the human skin. The results presented in the form of animated graphs of sampling volume changes for scaling of the parameters of the main human skin layers related to the results of experimental measurements are of particular interest for pulse oximetry, photoplethysmography, Doppler flowmetry, reflectance spectroscopy.

  12. Error sources in atomic force microscopy for dimensional measurements: Taxonomy and modeling

    DEFF Research Database (Denmark)

    Marinello, F.; Voltan, A.; Savio, E.

    2010-01-01

    This paper aimed at identifying the error sources that occur in dimensional measurements performed using atomic force microscopy. In particular, a set of characterization techniques for errors quantification is presented. The discussion on error sources is organized in four main categories......: scanning system, tip-surface interaction, environment, and data processing. The discussed errors include scaling effects, squareness errors, hysteresis, creep, tip convolution, and thermal drift. A mathematical model of the measurement system is eventually described, as a reference basis for errors...

  13. Precise quantification of dialysis using continuous sampling of spent dialysate and total dialysate volume measurement.

    Science.gov (United States)

    Argilés, A; Ficheux, A; Thomas, M; Bosc, J Y; Kerr, P G; Lorho, R; Flavier, J L; Stec, F; Adelé, C; Leblanc, M; Garred, L J; Canaud, B; Mion, H; Mion, C M

    1997-08-01

    The "gold standard" method to evaluate the mass balances achieved during dialysis for a given solute remains total dialysate collection (TDC). However, since handling over 100 liter volumes is unfeasible in our current dialysis units, alternative methods have been proposed, including urea kinetic modeling, partial dialysate collection (PDC) and more recently, monitoring of dialysate urea by on-line devices. Concerned by the complexity and costs generated by these devices, we aimed to adapt the simple "gold standard" TDC method to clinical practice by diminishing the total volumes to be handled. We describe a new system based on partial dialysate collection, the continuous spent sampling of dialysate (CSSD), and present its technical validation. Further, and for the first time, we report a long-term assessment of dialysis dosage in a dialysis clinic using both the classical PDC and the new CSSD system in a group of six stable dialysis patients who were followed for a period of three years. For the CSSD technique, spent dialysate was continuously sampled by a reversed automatic infusion pump at a rate of 10 ml/hr. The piston was automatically driven by the dialysis machine: switched on when dialysis started, off when dialysis terminated and held during the by pass periods. At the same time the number of production cycles of dialysate was monitored and the total volume of dialysate was calculated by multiplying the volume of the production chamber by the number of cycles. Urea and creatinine concentrations were measured in the syringe and the masses were obtained by multiplying this concentration by the total volume. CSSD and TDC were simultaneously performed in 20 dialysis sessions. The total mass of urea removed was calculated as 58038 and 60442 mmol/session (CSSD and TDC respectively; 3.1 +/- 1.2% variation; r = 0.99; y = 0.92x -28.9; P urea removal: 510 +/- 59 during the first year with PDC and 516 +/- 46 mmol/dialysis session during the third year, using CSSD

  14. High-precision RCS measurement of aircraft’s weak scattering source

    Directory of Open Access Journals (Sweden)

    Hu Chufeng

    2016-06-01

    Full Text Available The radar cross section (RCS of weak scattering source on the surface of an aircraft is usually less than −40 dBsm. How to accurately measure the RCS characteristics of weak scattering source is a technical challenge for the aircraft’s RCS measurement. This paper proposes separating and extracting the two-dimensional (2D reflectivity distribution of the weak scattering source with the microwave imaging algorithm and spectral transform so as to enhance its measurement precision. Firstly, we performed the 2D microwave imaging of the target and then used the 2D gating function to separate and extract the reflectivity distribution of the weak scattering source. Secondly, we carried out the spectral transform of the reflectivity distribution and eventually obtained the RCS of the weak scattering source through calibration. The prototype experimental results and their analysis show that the measurement method is effective. The experiments on an aircraft’s low-scattering conformal antenna verify that the measurement method can eliminate the clutter on the surface of aircraft. The precision of measuring a −40 dBsm target is 3–5 dB better than the existing RCS measurement methods. The measurement method can more accurately obtain the weak scattering source’s RCS characteristics.

  15. High-precision RCS measurement of aircraft’s weak scattering source

    Institute of Scientific and Technical Information of China (English)

    Hu Chufeng; Li Nanjing; Chen Weijun; Zhang Linxi

    2016-01-01

    The radar cross section (RCS) of weak scattering source on the surface of an aircraft is usually less than ?40 dBsm. How to accurately measure the RCS characteristics of weak scattering source is a technical challenge for the aircraft’s RCS measurement. This paper proposes separating and extracting the two-dimensional (2D) reflectivity distribution of the weak scattering source with the microwave imaging algorithm and spectral transform so as to enhance its measurement preci-sion. Firstly, we performed the 2D microwave imaging of the target and then used the 2D gating function to separate and extract the reflectivity distribution of the weak scattering source. Secondly, we carried out the spectral transform of the reflectivity distribution and eventually obtained the RCS of the weak scattering source through calibration. The prototype experimental results and their analysis show that the measurement method is effective. The experiments on an aircraft’s low-scattering conformal antenna verify that the measurement method can eliminate the clutter on the surface of aircraft. The precision of measuring a ?40 dBsm target is 3–5 dB better than the existing RCS measurement methods. The measurement method can more accurately obtain the weak scattering source’s RCS characteristics.

  16. Response of a BGO detector to photon and neutron sources simulations and measurements

    CERN Document Server

    Vincke, H H; Fabjan, Christian Wolfgang; Otto, T

    2002-01-01

    In this paper Monte Carlo simulations (FLUKA) and measurements of the response of a BGO detector are reported. %For the measurements different radioactive sources were used to irradiate the BGO crystal. For the measurements three low-energy photon emitters $\\left({}^{60}\\rm{Co},\\right.$ ${}^{54}\\rm{Mn},$ $\\left. {}^{137}\\rm{Cs}\\right)$ were used to irradiate the BGO from various distances and angles. The neutron response was measured with an Am--Be neutron source. Simulations of the experimental irradiations were carried out. Our study can also be considered as a benchmark for FLUKA in terms of its reliability to predict the detector response of a BGO scintillator.

  17. The fuzzy two-load method for measurement of ducted one-port source characteristics

    Science.gov (United States)

    Dokumaci, Erkan

    2017-06-01

    Knowledge of source characteristics is important for the calculation of sound pressure level and insertion loss of a silencer in sourced ducts. Measurement is usually the only feasible approach for the determination of source characteristics. The present paper is concerned with the measurement methods based on the Helmholtz-Thévenin equivalent of ducted one-port plane wave sources. Existing methods are classified as crisp and over-determined methods. In the crisp methods, the measured data are just sufficient for unique characterization of the source. This calls for two loads if their phase relative to the source is known, otherwise three loads are required. Over-determined methods use more number of loads than the crisp methods and are motivated for possible minimization of variations due to measurement errors. The point estimates for the source parameters are, however, still subject to some uncertainty, but estimation of confidence intervals is not feasible because the loads do not constitute a probability sample. The present paper proposes an approach which can yield the source characteristics in intervals from auto-power spectral density measurements with only two loads. The method is based on a novel Apollonian circle formulation. It is called the fuzzy two-load method, because uncertainty inherent to measurements is modelled by fuzzification of a characteristic parameter of the Apollonian circle of two loads. Fuzzy number transformations leading to the source pressure strength, sound pressure level and insertion loss interval predictions are discussed in depth. The paper includes an application showing the working features of the fuzzy two-load method.

  18. Dipole source analysis for readiness potential and field using simultaneously measured EEG and MEG signals.

    Science.gov (United States)

    Mideksa, K G; Hellriegel, H; Hoogenboom, N; Krause, H; Schnitzler, A; Deuschl, G; Raethjen, J; Heute, U; Muthuraman, M

    2013-01-01

    Various source localization techniques have indicated the generators of each identifiable component of movement-related cortical potentials, since the discovery of the surface negative potential prior to self-paced movement by Kornhuber and Decke. Readiness potentials and fields preceding self-paced finger movements were recorded simultaneously using multichannel electroencephalography (EEG) and magnetoencephalography (MEG) from five healthy subjects. The cortical areas involved in this paradigm are the supplementary motor area (SMA) (bilateral), pre-SMA (bilateral), and contralateral motor area of the moving finger. This hypothesis is tested in this paper using the dipole source analysis independently for only EEG, only MEG, and both combined. To localize the sources, the forward problem is first solved by using the boundary-element method for realistic head models and by using a locally-fitted-sphere approach for spherical head models consisting of a set of connected volumes, typically representing the scalp, skull, and brain. In the source reconstruction it is to be expected that EEG predominantly localizes radially oriented sources while MEG localizes tangential sources at the desired region of the cortex. The effect of MEG on EEG is also observed when analyzing both combined data. When comparing the two head models, the spherical and the realistic head models showed similar results. The significant points for this study are comparing the source analysis between the two modalities (EEG and MEG) so as to assure that EEG is sensitive to mostly radially orientated sources while MEG is only sensitive to only tangential sources, and comparing the spherical and individual head models.

  19. Water volume estimates of the Greenland Perennial Firn Aquifer from in situ measurements

    Science.gov (United States)

    Koenig, L.; Miege, C.; Forster, R. R.; Brucker, L.

    2013-12-01

    Improving our understanding of the complex Greenland hydrologic system is necessary for assessing change across the Greenland Ice Sheet and its contribution to sea level rise (SLR). A new component of the Greenland hydrologic system, a Perennial Firn Aquifer (PFA), was recently discovered in April 2011. The PFA represents a large storage of liquid water within the Greenland Ice Sheet with an area of 70,000 × 10,000 km2 simulated by the RACMO2/GR regional climate model which closely follows airborne radar-derived mapping (Forster et al., in press). The average top surface depth of the PFA as detected by radar is 23 m. In April 2013, our team drilled through the PFA for the first time to gain an understanding of firn structure constraining the PFA, to estimate the water volume within the PFA, and to measure PFA temperatures and densities. At our drill site in Southeast Greenland (~100 km Northwest of Kulusuk), water fills or partially fills the available firn pore space from depths of ~12 to 37 m. The temperature within the PFA depths is constant at 0.1 × 0.1° C while the 12 m of seasonally dry firn above the PFA has a temperature profile dominated by surface temperature forcing. Near the bottom of the PFA water completely fills available pore space as the firn is compressed to ice entrapping water filled bubbles, as opposed to air filled bubbles, which then start to refreeze. A PFA maximum density is reached as the water filling the pore space, increasing density, begins refreezing back into ice at a lower density. We define this depth as the pore water refreeze depth and use this depth as the bottom of the PFA to calculate volume. It is certain, however that a small amount of water does exist below this depth, which we do not account for. The density profile obtained from the ACT11B firn core, the closest seasonally dry firn core, is compared to both gravitational densities and high resolution densities derived from a neutron density probe at the PFA site. The

  20. Can endocranial volume be estimated accurately from external skull measurements in great-tailed grackles (Quiscalus mexicanus?

    Directory of Open Access Journals (Sweden)

    Corina J. Logan

    2015-06-01

    Full Text Available There is an increasing need to validate and collect data approximating brain size on individuals in the field to understand what evolutionary factors drive brain size variation within and across species. We investigated whether we could accurately estimate endocranial volume (a proxy for brain size, as measured by computerized tomography (CT scans, using external skull measurements and/or by filling skulls with beads and pouring them out into a graduated cylinder for male and female great-tailed grackles. We found that while females had higher correlations than males, estimations of endocranial volume from external skull measurements or beads did not tightly correlate with CT volumes. We found no accuracy in the ability of external skull measures to predict CT volumes because the prediction intervals for most data points overlapped extensively. We conclude that we are unable to detect individual differences in endocranial volume using external skull measurements. These results emphasize the importance of validating and explicitly quantifying the predictive accuracy of brain size proxies for each species and each sex.

  1. A Method for Measuring the Volume of Transdermally Extracted Interstitial Fluid by a Three-Electrode Skin Resistance Sensor

    Directory of Open Access Journals (Sweden)

    Dachao Li

    2014-04-01

    Full Text Available It is difficult to accurately measure the volume of transdermally extracted interstitial fluid (ISF, which is important for improving blood glucose prediction accuracy. Skin resistance, which is a good indicator of skin permeability, can be used to determine the volume of extracted ISF. However, it is a challenge to realize in vivo longitudinal skin resistance measurements of microareas. In this study, a three-electrode sensor was presented for measuring single-point skin resistance in vivo, and a method for determining the volume of transdermally extracted ISF using this sensor was proposed. Skin resistance was measured under static and dynamic conditions. The correlation between the skin resistance and the permeation rate of transdermally extracted ISF was proven. The volume of transdermally extracted ISF was determined using skin resistance. Factors affecting the volume prediction accuracy of transdermally extracted ISF were discussed. This method is expected to improve the accuracy of blood glucose prediction, and is of great significance for the clinical application of minimally invasive blood glucose measurement.

  2. Comparison of loess and purple rill erosions measured with volume replacement method

    Science.gov (United States)

    Chen, Xiao-yan; Huang, Yu-han; Zhao, Yu; Mo, Bin; Mi, Hong-xing

    2015-11-01

    Rills are commonly found on sloping farm fields in both the loess and the purple soil regions of China. A comparative study on rill erosion between the two soils is important to increase research knowledge and exchange application experiences. Rill erosion processes of loess and purple soils were determined through laboratory experiments with the volume replacement method. Water was used to refill the eroded rill segments to compute eroded volume before sediment concentration distribution along the rill was computed using the soil bulk density, flow rate, and water flow duration. The experimental loess soil materials were from the Loess Plateau and purple soil from the southwestern part of China, Chongqing City. A laboratory experimental platform was used to construct flumes to simulate rills with 12.0 m length, 0.1 m width, and 0.3 m depth. Soil materials were filled into the flumes at a bulk density of 1.2 g cm-3 to a depth of 20 cm to form rills for experiments on five slope gradients (5°, 10°, 15°, 20°, and 25°) and three flow rates (2, 4, and 8 L/min). After each experimental run under the given slope gradient and flow rate, the rill segments from the upper slope between 0-0.5, 0.5-1, 1-2, 2-3, …, 7-8, 8-10, and 10-12 m were lined with plastic sheets before be re-filled with water to determine sediment concentration after the eroded volumes was measured. Rill erosion differed between the two soils. As purple soil started to erode at a higher erosive force than loess soil, it possibly exhibits higher resistance to water erosion. The subsequent erosion process in the eroding purple rill was similar to that in the loess rill. However, the total erosion in the eroding loess rill was more than that in the eroding purple rill. The maximum sediment concentration transported by the eroding purple rills was significantly lower, approximately 55% of those transported by the loess rills under the same flow rate and slope gradient. Hence, less purple sediments can

  3. Best single-slice location to measure visceral adipose tissue on paediatric CT scans and the relationship between anthropometric measurements, gender and VAT volume in children

    OpenAIRE

    2015-01-01

    Objective: Visceral adipose tissue (VAT) is a significant risk factor for obesity-related metabolic diseases. This study investigates (1) the best single CT slice location for predicting total abdominal VAT volume in paediatrics and (2) the relationship between waist circumference (WC), sagittal diameter (SD), gender and VAT volume. Methods: A random sample of 130 paediatric abdomen CT scans, stratified according to age and gender, was collected. Three readers measured VAT area at each interv...

  4. Measurement and Analysis System for the Identification of Shielded Neutron Sources

    Energy Technology Data Exchange (ETDEWEB)

    Flaska, Marek [ORNL; Pozzi, Sara A [ORNL

    2007-01-01

    Accurate identification of radioactive materials is essential in areas such as nuclear nonproliferation, international safeguards, nuclear material control and accountability, and national security. Recently, a new application of a technique that acquires neutron pulse-height spectra using a liquid scintillation detector, a digitizer, and an optimized pulse shape discrimination technique was proposed. The method can be used for accurate identification of neutron sources such as Cf-252, Am-Be, and Am-Li. All these sources were investigated in combination with several shielding blocks made of polyethylene and lead. From the results it is apparent that source identification is possible by the data inspection of the measured pulse-height distributions. The general slope of the distributions can be used for the source identification and all sources tested can be accurately identified. All measured pulse-height distributions were also compared to distributions simulated with the MCNP-PoliMi code and very good agreement was achieved.

  5. Brightness measurement of an electron impact gas ion source for proton beam writing applications

    Energy Technology Data Exchange (ETDEWEB)

    Liu, N.; Santhana Raman, P. [Centre for Ion Beam Applications, Department of Physics, National University of Singapore, Singapore 117542 (Singapore); Department of Electrical and Computer Engineering, National University of Singapore, Singapore 117583 (Singapore); Xu, X.; Pang, R.; Kan, J. A. van, E-mail: phyjavk@nus.edu.sg [Centre for Ion Beam Applications, Department of Physics, National University of Singapore, Singapore 117542 (Singapore); Khursheed, A. [Department of Electrical and Computer Engineering, National University of Singapore, Singapore 117583 (Singapore)

    2016-02-15

    We are developing a high brightness nano-aperture electron impact gas ion source, which can create ion beams from a miniature ionization chamber with relatively small virtual source sizes, typically around 100 nm. A prototype source of this kind was designed and successively micro-fabricated using integrated circuit technology. Experiments to measure source brightness were performed inside a field emission scanning electron microscope. The total output current was measured to be between 200 and 300 pA. The highest estimated reduced brightness was found to be comparable to the injecting focused electron beam reduced brightness. This translates into an ion reduced brightness that is significantly better than that of conventional radio frequency ion sources, currently used in single-ended MeV accelerators.

  6. Renal cortical volume measured using automatic contouring software for computed tomography and its relationship with BMI, age and renal function

    Energy Technology Data Exchange (ETDEWEB)

    Muto, Natalia Sayuri, E-mail: nataliamuto@gmail.com [Department of Radiology, Hokkaido University Hospital, N15 W7, kita-ku, Sapporo City, 0608638 (Japan); Kamishima, Tamotsu, E-mail: ktamotamo2@yahoo.co.jp [Department of Radiology, Hokkaido University Hospital, N15 W7, kita-ku, Sapporo City, 0608638 (Japan); Harris, Ardene A., E-mail: ardene_b@yahoo.com [Department of Radiology, Hokkaido University Hospital, N15 W7, kita-ku, Sapporo City, 0608638 (Japan); Kato, Fumi, E-mail: fumikato@med.hokudai.ac.jp [Department of Radiology, Hokkaido University Hospital, N15 W7, kita-ku, Sapporo City, 0608638 (Japan); Onodera, Yuya, E-mail: yuyaonodera@med.hokudai.ac.jp [Department of Radiology, Hokkaido University Hospital, N15 W7, kita-ku, Sapporo City, 0608638 (Japan); Terae, Satoshi, E-mail: saterae@yahoo.co.jp [Department of Radiology, Hokkaido University Hospital, N15 W7, kita-ku, Sapporo City, 0608638 (Japan); Shirato, Hiroki, E-mail: shirato@med.hokudai.ac.jp [Department of Radiology, Hokkaido University Hospital, N15 W7, kita-ku, Sapporo City, 0608638 (Japan)

    2011-04-15

    Purpose: To evaluate the relationship between renal cortical volume, measured by an automatic contouring software, with body mass index (BMI), age and renal function. Materials and methods: The study was performed in accordance to the institutional guidelines at our hospital. Sixty-four patients (34 men, 30 women), aged 19 to 79 years had their CT scans for diagnosis or follow-up of hepatocellular carcinoma retrospectively examined by a computer workstation using a software that automatically contours the renal cortex and the renal parenchyma. Body mass index and estimated glomerular filtration rate (eGFR) were calculated based on data collected. Statistical analysis was done using the Student t-test, multiple regression analysis, and intraclass correlation coefficient (ICC). Results: The ICC for total renal and renal cortical volumes were 0.98 and 0.99, respectively. Renal volume measurements yielded a mean cortical volume of 105.8 cm{sup 3} {+-} 28.4 SD, mean total volume of 153 cm{sup 3} {+-} 39 SD and mean medullary volume of 47.8 cm{sup 3} {+-} 19.5 SD. The correlation between body weight/height/BMI and both total renal and cortical volumes presented r = 0.6, 0.6 and 0.4, respectively, p < 0.05, while the correlation between renal cortex and age was r = -0.3, p < 0.05. eGFR showed correlation with renal cortical volume r = 0.6, p < 0.05. Conclusion: This study demonstrated that renal cortical volume had a moderate positive relationship with BMI, moderate negative relationship with age, and a strong positive relationship with the renal function, and provided a new method to routinely produce volumetric assessment of the kidney.

  7. Measurement of Throughput Variation Across A Large Format Volume-Phase Holographic Grating

    CERN Document Server

    Tamura, N; Sharples, R M; Robertson, D J; Allington-Smith, J R; Tamura, Naoyuki; Murray, Graham J.; Sharples, Ray M.; Robertson, David J.

    2005-01-01

    In this paper, we report measurements of diffraction efficiency and angular dispersion for a large format (~ 25 cm diameter) Volume-Phase Holographic (VPH) grating optimized for near-infrared wavelengths (0.9 -- 1.8 micron). The aim of this experiment is to see whether optical characteristics vary significantly across the grating. We sampled three positions in the grating aperture with a separation of 5 cm between each. A 2 cm diameter beam is used to illuminate the grating. At each position, throughput and diffraction angle were measured at several wavelengths. It is found that whilst the relationship between diffraction angle and wavelength is nearly the same at the three positions, the throughputs vary by up to ~ 10\\% from position to position. We explore the origin of the throughput variation by comparing the data with predictions from coupled-wave analysis. We find that it can be explained by a combination of small variations over the grating aperture in gelatin depth and/or refractive index modulation a...

  8. Curling probe measurement of large-volume pulsed plasma confined by surface magnetic field

    Science.gov (United States)

    Pandey, Anil; Sakakibara, Wataru; Matsuoka, Hiroyuki; Nakamura, Keiji; Sugai, Hideo; Chubu University Team; DOWA Thermotech Collaboration

    2015-09-01

    Curling probe (CP) has recently been developed which enables the local electron density measurement even in plasma for non-conducting film CVD. The electron density is obtained from a shift of resonance frequency of spiral antenna in discharge ON and OFF monitored by a network analyzer (NWA). In case of a pulsed glow discharge, synchronization of discharge pulse with frequency sweep of NWA must be established. In this paper, we report time and space-resolved CP measurement of electron density in a large volume plasma (80 cm diameter, 110 cm length) confined by surface magnetic field (multipole cusp field ~0.03 T). For plasma-aided modification of metal surface, the plasma is produced by 1 kV glow discharge at pulse frequency of 0.3 - 25 kHz with various duty ratio in gas (Ar, N2, C2H2) at pressure ~ 1 Pa. A radially movable CP revealed a remarkable effect of surface magnetic confinement: detach of plasma from the vessel wall and a fairly uniform plasma in the central region. In afterglow phase, the electron density was observed to decrease much faster in C2H2 discharge than in Ar discharge.

  9. Splenic volume measurements on computed tomography utilizing automatically contouring software and its relationship with age, gender, and anthropometric parameters

    Energy Technology Data Exchange (ETDEWEB)

    Harris, Ardene, E-mail: ardene_b@yahoo.co [Department of Radiology, Hokkaido University Hospital, North 15, West 7, Kita-ku, Sapporo 060-0815 (Japan); Kamishima, Tamotsu, E-mail: ktamotamo2@yahoo.co.j [Department of Radiology, Hokkaido University Hospital, North 15, West 7, Kita-ku, Sapporo 060-0815 (Japan); Hao, Hong Yi, E-mail: haohongyi88@yahoo.co.j [Department of Radiology, Hokkaido University Hospital, North 15, West 7, Kita-ku, Sapporo 060-0815 (Japan); Kato, Fumi [Department of Radiology, Hokkaido University Hospital, North 15, West 7, Kita-ku, Sapporo 060-0815 (Japan); Omatsu, Tokuhiko, E-mail: omatoku@me.co [Department of Radiology, Hokkaido University Hospital, North 15, West 7, Kita-ku, Sapporo 060-0815 (Japan); Onodera, Yuya, E-mail: yuyaonodera@med.hokudai.ac.j [Department of Radiology, Hokkaido University Hospital, North 15, West 7, Kita-ku, Sapporo 060-0815 (Japan); Terae, Satoshi, E-mail: saterae@med.hokudai.ac.j [Department of Radiology, Hokkaido University Hospital, North 15, West 7, Kita-ku, Sapporo 060-0815 (Japan); Shirato, Hiroki, E-mail: shirato@med.hokudai.ac.j [Department of Radiology, Hokkaido University Hospital, North 15, West 7, Kita-ku, Sapporo 060-0815 (Japan)

    2010-07-15

    Objective: The present research was conducted to establish the normal splenic volume in adults using a novel and fast technique. The relationship between splenic volume and age, gender, and anthropometric parameters was also examined. Materials and methods: The splenic volume was measured in 230 consecutive patients who underwent computed tomography (CT) scans for various indications. Patients with conditions that have known effect on the spleen size were not included in this study. A new technique using volumetric software to automatically contour the spleen in each CT slice and quickly calculate splenic volume was employed. Inter- and intra-observer variability were also examined. Results: The average splenic volume of all the subjects was 127.4 {+-} 62.9 cm{sup 3}, ranging from 22 to 417 cm{sup 3}. The splenic volume (S) correlated with age (A) (r = -0.33, p < 0.0001), body weight (W) (r = 0.35, p < 0.0001), body mass index (r = 0.24, p < 0.0001) and body surface area (BSA) (r = 0.31, p < 0.0001). The age-adjusted splenic volume index correlated with gender (p = 0.0089). The formulae S = W[6.47A{sup (-0.31)}] and S = BSA[278A{sup (-0.36)}] were derived and can be used to estimate the splenic volume. Inter- and intra-observer variability were 6.4 {+-} 9.8% and 2.8 {+-} 3.5% respectively. Conclusion: Of the anthropometric parameters, the splenic volume was most closely linked to body weight. The automatically contouring software as well as formulae can be used to obtain the volume of the spleen in regular practice.

  10. Assessment of Volume Measurement of Breast Cancer-Related Lymphedema by Three Methods: Circumference Measurement, Water Displacement, and Dual Energy X-Ray Absorptiometry

    DEFF Research Database (Denmark)

    Gjørup, Caroline; Zerahn, B.; Hendel, Helle Westergren

    2010-01-01

    Background: Following treatment for breast cancer 12%-60% develop breast cancer-related lymphedema (BCRL). There are several ways of assessing BCRL. Circumference measurement (CM) and water displacement (WD) for volume measurements (VM) are frequently used methods in practice and research...

  11. Design aspects of a compact, single-frequency, permanent magnet ECR ion source with a large uniformly distributed resonant plasma volume

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Y.; Alton, G.D.; Mills, G.D.; Reed, C.A.; Haynes, D.L.

    1997-09-01

    A compact, all-permanent-magnet single-frequency ECR ion source with a large uniformly distributed ECR plasma volume has been designed and is presently under construction at the Oak Ridge National Laboratory (ORNL). The central region of the field is designed to achieve a flat-field (constant mod-B) which extends over the length of the central field region along the axis of symmetry and radially outward to form a uniformly distributed ECR plasma volume. The magnetic field design strongly contrasts with those used in conventional ECR ion sources where the central field regions are approximately parabolic and the consequent ECR zones are surfaces. The plasma confinement magnetic field mirror has a mirror ratio B{sub max}/B{sub ECR} of slightly greater than two. The source is designed to operate at a nominal RF frequency of 6 GHz. The central flat magnetic field region can be easily adjusted by mechanical means to tune the source to the resonant conditions within the limits of 5.5 to 6.8 GHz. The RF injection system is broadband to ensure excitation of transverse electric (TE) modes so that the RF power is largely concentrated in the resonant plasma volume which lies along and surrounds the axis of symmetry of the source. Because of the much larger ECR zone, the probability for absorption of microwave power is dramatically increased thereby increasing the probability for acceleration of electrons, the electron temperature of the plasma and, consequently, the hot electron population within the plasma volume of the source. The creation of an ECR volume rather than a surface is commensurate with higher charge states and higher beam intensities within a particular charge state.

  12. Dose response explorer: an integrated open-source tool for exploring and modelling radiotherapy dose-volume outcome relationships

    Energy Technology Data Exchange (ETDEWEB)

    Naqa, I El [Washington University, Saint Louis, MO (United States); Suneja, G [Brown Medical School, Providence, RI (United States); Lindsay, P E [Washington University, St. Louis, MO (United States); Hope, A J [Washington University, Saint Louis, MO (United States); Alaly, J R [Washington University, Saint Louis, MO (United States); Vicic, M [Washington University, Saint Louis, MO (United States); Bradley, J D [Washington University, Saint Louis, MO (United States); Apte, A [Washington University, Saint Louis, MO (United States); Deasy, J O [Washington University, Saint Louis, MO (United States)

    2006-11-21

    Radiotherapy treatment outcome models are a complicated function of treatment, clinical and biological factors. Our objective is to provide clinicians and scientists with an accurate, flexible and user-friendly software tool to explore radiotherapy outcomes data and build statistical tumour control or normal tissue complications models. The software tool, called the dose response explorer system (DREES), is based on Matlab, and uses a named-field structure array data type. DREES/Matlab in combination with another open-source tool (CERR) provides an environment for analysing treatment outcomes. DREES provides many radiotherapy outcome modelling features, including (1) fitting of analytical normal tissue complication probability (NTCP) and tumour control probability (TCP) models, (2) combined modelling of multiple dose-volume variables (e.g., mean dose, max dose, etc) and clinical factors (age, gender, stage, etc) using multi-term regression modelling, (3) manual or automated selection of logistic or actuarial model variables using bootstrap statistical resampling, (4) estimation of uncertainty in model parameters, (5) performance assessment of univariate and multivariate analyses using Spearman's rank correlation and chi-square statistics, boxplots, nomograms, Kaplan-Meier survival plots, and receiver operating characteristics curves, and (6) graphical capabilities to visualize NTCP or TCP prediction versus selected variable models using various plots. DREES provides clinical researchers with a tool customized for radiotherapy outcome modelling. DREES is freely distributed. We expect to continue developing DREES based on user feedback.

  13. Dose response explorer: an integrated open-source tool for exploring and modelling radiotherapy dose volume outcome relationships

    Science.gov (United States)

    El Naqa, I.; Suneja, G.; Lindsay, P. E.; Hope, A. J.; Alaly, J. R.; Vicic, M.; Bradley, J. D.; Apte, A.; Deasy, J. O.

    2006-11-01

    Radiotherapy treatment outcome models are a complicated function of treatment, clinical and biological factors. Our objective is to provide clinicians and scientists with an accurate, flexible and user-friendly software tool to explore radiotherapy outcomes data and build statistical tumour control or normal tissue complications models. The software tool, called the dose response explorer system (DREES), is based on Matlab, and uses a named-field structure array data type. DREES/Matlab in combination with another open-source tool (CERR) provides an environment for analysing treatment outcomes. DREES provides many radiotherapy outcome modelling features, including (1) fitting of analytical normal tissue complication probability (NTCP) and tumour control probability (TCP) models, (2) combined modelling of multiple dose-volume variables (e.g., mean dose, max dose, etc) and clinical factors (age, gender, stage, etc) using multi-term regression modelling, (3) manual or automated selection of logistic or actuarial model variables using bootstrap statistical resampling, (4) estimation of uncertainty in model parameters, (5) performance assessment of univariate and multivariate analyses using Spearman's rank correlation and chi-square statistics, boxplots, nomograms, Kaplan-Meier survival plots, and receiver operating characteristics curves, and (6) graphical capabilities to visualize NTCP or TCP prediction versus selected variable models using various plots. DREES provides clinical researchers with a tool customized for radiotherapy outcome modelling. DREES is freely distributed. We expect to continue developing DREES based on user feedback.

  14. Performance of a corona ion source for measurement of sulfuric acid by chemical ionization mass spectrometry

    Directory of Open Access Journals (Sweden)

    A. Kürten

    2010-11-01

    Full Text Available The performance of an ion source based on corona discharge has been studied. This source is used for the detection of gaseous sulfuric acid by chemical ionization mass spectrometry (CIMS through the reaction of NO3 ions with H2SO4. The ion source is operated under atmospheric pressure and its design is similar to the one of a radioactive (Americium 241 ion source which has been used previously. Our results show that the detection limit for the corona ion source is sufficiently good for most applications. For an integration time of one minute it is ~6 × 104 molecules of H2SO4 per cm3. In addition, only a small cross-sensitivity to SO2 has been observed for concentrations as high as 1 ppmv in the sample gas. This low sensitivity to SO2 is achieved even without the addition of an OH scavenger. When comparing the new corona ion source with the americium ion source for the same provided H2SO4 concentration, both ion sources yield almost identical values. These features make the corona ion source investigated here favorable over the more commonly used radioactive ion sources for most applications where H2SO4 is measured by CIMS.

  15. Performance of a corona ion source for measurement of sulfuric acid by chemical ionization mass spectrometry

    Directory of Open Access Journals (Sweden)

    A. Kürten

    2011-03-01

    Full Text Available The performance of an ion source based on corona discharge has been studied. This source is used for the detection of gaseous sulfuric acid by chemical ionization mass spectrometry (CIMS through the reaction of NO3 ions with H2SO4. The ion source is operated under atmospheric pressure and its design is similar to the one of a radioactive (americium-241 ion source which has been used previously. The results show that the detection limit for the corona ion source is sufficiently good for most applications. For an integration time of 1 min it is ~6 × 104 molecule cm−3 of H2SO4. In addition, only a small cross-sensitivity to SO2 has been observed for concentrations as high as 1 ppmv in the sample gas. This low sensitivity to SO2 is achieved even without the addition of an OH scavenger. When comparing the new corona ion source with the americium ion source for the same provided H2SO4 concentration, both ion sources yield almost identical values. These features make the corona ion source investigated here favorable over the more commonly used radioactive ion sources for most applications where H2SO4 is measured by CIMS.

  16. Measurement of breast volume is a useful supplement to select candidates for surgical breast reduction

    DEFF Research Database (Denmark)

    Ikander, Peder; Drejøe, Jennifer Berg; Lumholt, Pavia

    2014-01-01

    -off values for breast volume were calculated based on whether or not the patients were offered reduction surgery. Most patients (93%) with a breast volume below 800 cc were not offered surgery, while most with a volume exceeding 900 cc were offered surgery (94%). In the grey zone between 800 and 900 cc...... with breast hypertrophy as a tool which facilitates their decision-making and patients' acceptance of the decisions made. FUNDING: not relevant. TRIAL REGISTRATION: not relevant....

  17. Effects of pore-scale dispersion, degree of heterogeneity, sampling size, and source volume on the concentration moments of conservative solutes in heterogeneous formations

    Science.gov (United States)

    Daniele Tonina; Alberto Bellin

    2008-01-01

    Pore-scale dispersion (PSD), aquifer heterogeneity, sampling volume, and source size influence solute concentrations of conservative tracers transported in heterogeneous porous formations. In this work, we developed a new set of analytical solutions for the concentration ensemble mean, variance, and coefficient of variation (CV), which consider the effects of all these...

  18. Volume measurements of 28Si-enriched spheres using an improved optical interferometer for the determination of the Avogadro constant

    Science.gov (United States)

    Kuramoto, Naoki; Azuma, Yasushi; Inaba, Hajime; Fujii, Kenichi

    2017-04-01

    For the determination of the Avogadro constant by the x-ray crystal density method, an accurate volume measurement of 1 kg Si spheres is of primary importance. For this purpose, an optical interferometer was improved and used to measure the volumes of two 1 kg silicon spheres which were manufactured from a silicon crystal highly enriched in 28Si. The apparent volumes of the spheres, which do not take into account the influence of the surface layers on the volume measurement by interferometry, were determined with a relative standard uncertainty of as small as 2.0  ×  10‑8. The surface of the spheres was characterized by using an improved spectroscopic ellipsometer. By considering the influence of the surface layers, the core volumes of the spheres, which exclude the surface layers, were determined. These results were used for the determination of the Avogadro constant in 2015 as a framework organized by the International Avogadro Coordination project. This paper provides details on the measurements, the improvements made to the apparatus, the data analysis and the uncertainty evaluation.

  19. Volume and enthalpy changes of proton transfers in the bacteriorhodopsin photocycle studied by millisecond time-resolved photopressure measurements.

    Science.gov (United States)

    Liu, Yan; Edens, Gregory J; Grzymski, Joseph; Mauzerall, David

    2008-07-22

    The volume and enthalpy changes associated with proton translocation steps during the bacteriorhodopsin (BR) photocycle were determined by time-resolved photopressure measurements. The data at 25 degrees C show a prompt increase in volume followed by two further increases and one decrease to the original state to complete the cycle. These volume changes are decomposed into enthalpy and inherent volume changes. The positive enthalpy changes support the argument for inherent entropy-driven late steps in the BR photocycle [Ort, D. R., and Parson, W. M. (1979) Enthalpy changes during the photochemical cycle of bacteriorhodopsin. Biophys. J. 25, 355-364]. The volume change data can be interpreted by the electrostriction effect as charges are canceled and formed during the proton transfers. A simple glutamic acid-glutamate ion model or a diglutamate-arginine-protonated water charge-delocalized model for the proton-release complex (PRC) fit the data. A conformational change with a large positive volume change is required in the slower rise (M --> N of the optical cycle) step and is reversed in the decay (N --> O --> BR) steps. The large variation in the published values for both the volume and enthalpy changes is greatly ameliorated if the values are presented per absorbed photon instead of per mole of BR. Thus, it is the highly differing assumptions about the quantum or reaction yields that cause the variations in the published results.

  20. Idealized Shale Sorption Isotherm Measurements to Determine Pore Volume, Pore Size Distribution, and Surface Area

    Science.gov (United States)

    Holmes, R.; Wang, B.; Aljama, H.; Rupp, E.; Wilcox, J.

    2014-12-01

    One method for mitigating the impacts of anthropogenic CO2-related climate change is the sequestration of CO2 in depleted gas and oil reservoirs, including shale. The accurate characterization of the heterogeneous material properties of shale, including pore volume, surface area, pore size distributions (PSDs) and composition is needed to understand the interaction of CO2 with shale. Idealized powdered shale sorption isotherms were created by varying incremental amounts of four essential components by weight. The first two components, organic carbon and clay, have been shown to be the most important components for CO2 uptake in shales. Organic carbon was represented by kerogen isolated from a Silurian shale, and clay groups were represented by illite from the Green River shale formation. The rest of the idealized shale was composed of equal parts by weight of SiO2 to represent quartz and CaCO3 to represent carbonate components. Baltic, Eagle Ford, and Barnett shale sorption measurements were used to validate the idealized samples. The idealized and validation shale sorption isotherms were measured volumetrically using low pressure N2 (77K) and CO2 (273K) adsorbates on a Quantachrome Autosorb IQ2. Gravimetric isotherms were also produced for a subset of these samples using CO2 and CH4adsorbates under subsurface temperature and pressure conditions using a Rubotherm magnetic suspension balance. Preliminary analyses were inconclusive in validating the idealized samples. This could be a result of conflicting reports of total organic carbon (TOC) content in each sample, a problem stemming from the heterogeneity of the samples and different techniques used for measuring TOC content. The TOC content of the validation samples (Eagle Ford and Barnett) was measured by Rock-Eval pyrolysis at Weatherford Laboratories, while the TOC content in the Baltic validation samples was determined by LECO TOC. Development of a uniform process for measuring TOC in the validation samples is

  1. Effect of Sildenafil on Pressure–Volume Loop Measures of Ventricular Function in Fontan Patients

    Science.gov (United States)

    Butts, Ryan J.; Chowdhury, Shahryar M.; Baker, George H.; Bandisode, Varsha; Savage, Andrew J.; Atz, Andrew M.

    2016-01-01

    Sildenafil has been reported to improve exercise capacity in Fontan patients, but the physiologic mechanisms behind these findings are not completely understood. The objective of this study was to study the acute effect of sildenafil on pressure–volume loop (PVL) measures of ventricular function in Fontan patients. Patients after Fontan operation who were presenting for a clinically indicated catheterization were enrolled. Patients were randomized in a double-blinded fashion to receive placebo (n = 9) or sildenafil (n = 10) 30–90 min prior to catheterization. PVLs were recorded using microconductance catheters at baseline and after infusion of dobutamine (10 mcg/kg/min). The primary outcome was change in ventriculoarterial (VA) coupling. For the entire cohort, VA coupling trended toward improvement with dobutamine (1.4 ± 0.4 to 1.8 ± 0.9, p = 0.07). End-systolic elastance showed improvement (2.6 ± 0.9 to 3.8 ± 1.4 mmHg m2/ml, p sildenafil cohort trended toward having less of an improvement in VA coupling with dobutamine stress (p = 0.06). There were no differences between PVL measures of systolic or diastolic function between treatment groups, both at baseline and after dobutamine infusion. Patients with Fontan circulation had improved contractility and trended toward improvement in VA coupling with dobutamine stress. Acute sildenafil administration was not associated with improved PVL measurements of ventricular function in this population. These results suggest that clinical improvements seen with administration of sildenafil in Fontan patients are not associated with an acute improvement in ventricular function. PMID:26409473

  2. Assessment of the intraobserver and interobserver reliability of a communicating vessels volumeter to measure wrist-hand volume.

    Science.gov (United States)

    de Carvalho, Rogério Mendonca; Perez, Maria Del Carmen Janerio; Miranda, Fausto

    2012-10-01

    Traditional volumetry based on Archimedes' principle is the gold standard for the measurement of limb volume, but the routine use of this technique is discouraged because of several disadvantages. The purpose of this study was to evaluate intraobserver and interobserver reliability of direct measurements of wrist-hand volume using a new communicating vessels volumeter based on Pascal's law. A reliability study was conducted. To evaluate the reliability of the communicating vessels volumeter in generating measurements, 30 hands of 15 participants (9 women, 6 men) were measured 3 times each by 3 observers, totaling 270 volumetric results. Measurement time was short (X =3 minutes 42 seconds). The intraclass correlation coefficient (ICC) was .9977 for observer 1 and .9976 for observers 2 and 3. The interobserver ICC was .9998. The standard error of measurement was about 3 mL for all observers; the interobserver result was 1 mL. The interrater coefficient of variance (CV) was 1.15% for the series of 9 measurements collected for each segment; the intrarater CV was 1.20%. Limitations No swollen hands were measured, and measurements were not compared with the gold standard technique. Thus, accuracy of the new volumeter was not determined in this study. A new device has been developed for plethysmography of the extremities, and the results of its use to measure the volume of the wrist-hand segment were reliable in both intraobserver and interobserver analyses.

  3. Measurement of hold-up volumes in reverse-phase liquid chromatography Definition and comparison between static and dynamic methods.

    Science.gov (United States)

    Gritti, Fabrice; Kazakevich, Yuri; Guiochon, Georges

    2007-08-17

    The hold-up volumes, V(M) of two series of RPLC adsorbents were measured using three different approaches. The first method is based on the difference between the volumes of the empty column tube (150x4.6mm) and of the material packed inside the column. It is considered as giving the correct value of V(M). This method combines the results of the BET characterization of the adsorbent before packing (giving the specific pore volume), of carbon element analysis (giving the mass fraction of silica and alkyl bonded chains), of Helium pycnometry (providing silica density), and of inverse size exclusion chromatography (ISEC) performed on the packed column (yielding the interparticle volume). The second method is static pycnometry, which consists in weighing the masses of the chromatographic column filled with two distinct solvents of different densities. The last method is based on the thermodynamic definition of the hold-up volume and uses the dynamic minor disturbance method (MDM) with binary eluents. The experimental results of these three non-destructive methods are compared. They exhibit significant, systematic differences. Pycnometry underestimates V(M) by a few percent for adsorbents having a high carbon content. The results of the MDM method depend strongly on the choice of the binary solution used and may underestimate or overestimate V(M). The hold-up volume V(M) of the RPLC adsorbents tested is best measured by the MDM method using a mixture of ethanol and water.

  4. A method for the coherence measurement of the supercontinuum source using Michelson interferometer

    Science.gov (United States)

    Semenova, V. A.; Tsypkin, A. V.; Putilin, S. E.; Bespalov, V. G.

    2014-09-01

    Coherent properties of supercontinuum sources are highly significant for various applications, including low-coherence interferometry and optical frequency metrology. We propose a fast method for the spatial and temporal self-coherence of the SC measurement using Michelson interferometer without a mirror movement. Furthermore, we present self-coherence measurements of the supercontinuum, generated in microstructured fiber at 780 nm.

  5. Standardization of flux chambers and wind tunnels for area source emission measurements at animal feeding operations

    Science.gov (United States)

    Researchers and practitioners have used many varied designs of wind tunnels and flux chambers to measure the flux of volatile organic compounds, odor, and ammonia from area sources at animal feeding operations. The measured fluxes are used to estimate emission factors or compare treatments. We sho...

  6. Spatial resolution and measurement uncertainty of strains in bone and bone-cement interface using digital volume correlation.

    Science.gov (United States)

    Zhu, Ming-Liang; Zhang, Qing-Hang; Lupton, Colin; Tong, Jie

    2016-04-01

    The measurement uncertainty of strains has been assessed in a bone analogue (sawbone), bovine trabecular bone and bone-cement interface specimens under zero load using the Digital Volume Correlation (DVC) method. The effects of sub-volume size, sample constraint and preload on the measured strain uncertainty have been examined. There is generally a trade-off between the measurement uncertainty and the spatial resolution. Suitable sub-volume sizes have been be selected based on a compromise between the measurement uncertainty and the spatial resolution of the cases considered. A ratio of sub-volume size to a microstructure characteristic (Tb.Sp) was introduced to reflect a suitable spatial resolution, and the measurement uncertainty associated was assessed. Specifically, ratios between 1.6 and 4 appear to give rise to standard deviations in the measured strains between 166 and 620 με in all the cases considered, which would seem to suffice for strain analysis in pre as well as post yield loading regimes. A microscale finite element (μFE) model was built from the CT images of the sawbone, and the results from the μFE model and a continuum FE model were compared with those from the DVC. The strain results were found to differ significantly between the two methods at tissue level, consistent in trend with the results found in human bones, indicating mainly a limitation of the current DVC method in mapping strains at this level.

  7. Development of source range measurement instrument in Xi'an pulsed reactor

    CERN Document Server

    Wang Li

    2002-01-01

    Source range measurement instrument in Xi'an pulsed reactor is key equipment of low-side measuring in source range. At the same time, it is also weighty component of out-of-pile neutron-flux level observation system. The authors have done some researching and renovating based on the similar type devices used in nuclear reactor to improve the meter sensitivity, measuring range, noise proof features, reliability in running and maintainability which belong to the main performance index of the instrument. The design ideas, configurations, working principle, performance indexes, technique features and effect in utilizing are introduced briefly

  8. Single element of the matrix source of negative hydrogen ions: Measurements of the extracted currents combined with diagnostics

    Energy Technology Data Exchange (ETDEWEB)

    Yordanov, D., E-mail: yordanov@phys.uni-sofia.bg; Lishev, St.; Shivarova, A. [Faculty of Physics, Sofia University, BG-1164 Sofia (Bulgaria)

    2016-02-15

    Combining measurements of the extracted currents with probe and laser-photodetachment diagnostics, the study is an extension of recent tests of factors and gas-discharge conditions stimulating the extraction of volume produced negative ions. The experiment is in a single element of a rf source with the design of a matrix of small-radius inductively driven discharges. The results are for the electron and negative-ion densities, for the plasma potential and for the electronegativity in the vicinity of the plasma electrode as well as for the currents of the extracted negative ions and electrons. The plasma-electrode bias and the rf power have been varied. Necessity of a high bias to the plasma electrode and stable linear increase of the extracted currents with the rf power are the main conclusions.

  9. Measuring Acoustic Wave Transit Time in Furnace Based on Active Acoustic Source Signal

    Institute of Scientific and Technical Information of China (English)

    Zhen Luo; Feng Tian; Xiao-Ping Sun

    2007-01-01

    Accurate measurement of transit time for acoustic wave between two sensors installed on two sides of a furnace is a key to implementing the temperature field measurement technique based on acoustical method. A new method for measuring transit time of acoustic wave based on active acoustic source signal is proposed in this paper, which includes the followings: the time when the acoustic source signal arrives at the two sensors is measured first; then, the difference of two arriving time arguments is computed, thereby we get the transit time of the acoustic wave between two sensors installed on the two sides of the furnace. Avoiding the restriction on acoustic source signal and background noise, the new method can get the transit time of acoustic wave with higher precision and stronger ability of resisting noise interference.

  10. Electrical shielding box measurement of the negative hydrogen beam from Penning ion gauge ion source.

    Science.gov (United States)

    Wang, T; Yang, Z; Dong, P; long, J D; He, X Z; Wang, X; Zhang, K Z; Zhang, L W

    2012-06-01

    The cold-cathode Penning ion gauge (PIG) type ion source has been used for generation of negative hydrogen (H(-)) ions as the internal ion source of a compact cyclotron. A novel method called electrical shielding box dc beam measurement is described in this paper, and the beam intensity was measured under dc extraction inside an electrical shielding box. The results of the trajectory simulation and dc H(-) beam extraction measurement were presented. The effect of gas flow rate, magnetic field strength, arc current, and extraction voltage were also discussed. In conclusion, the dc H(-) beam current of about 4 mA from the PIG ion source with the puller voltage of 40 kV and arc current of 1.31 A was extrapolated from the measurement at low extraction dc voltages.

  11. The influence of sample volume applied to the Makler sperm counting chamber upon the measured concentration of latex beads:A multi-centre study

    Institute of Scientific and Technical Information of China (English)

    Melanie Walls; Cherise Mooy; Patrick Mohan; Sally Catt; Matthew Wiltshire; Hassan W Bakos; Mary Whyte; Phillip Matson; Emily Zuvela; Cheryl Ayres; Deborah Sherrin; Asma Chhotani; Liz Butler; Kelli Peirce; Jenny Krapez; Renae Parker

    2012-01-01

    Objective:To undertake a multi-centre study to maximize the number ofMakler chambers used.Methods:A total of15 laboratories participated with31Makler chambers.A suspension of latex beads was prepared to a concentration of20 millions per milliliter, and0.5 mL aliquots distributed to each participating laboratory.They measured the concentration on theirMakler chamber(s) used for routine semen analysis by adding3,4,5,7 and10µL volumes of bead suspension to the chamber.Results:There was no difference in within-chamber analysis of the bead concentration according to the volume of bead suspension applied within the range of 3-10µL(F4,14=2.634,P=0.056).However, the between-chamber effects were significantly different (F30,124=4.937,P=0.000), and24/31(77.5%) chambers tested had an average bias>10% compared to the target bead concentration.Conclusions:A volume of3-10µL added toMakler counting chambers does not influence the concentration measured of latex beads, but the between-chamber variability and positive bias seen would suggest that other sources of error are present which are yet to be identified.

  12. Left ventricular volume measurement in mice by conductance catheter: evaluation and optimization of calibration

    DEFF Research Database (Denmark)

    Nielsen, Jan Møller; Kristiansen, Steen B; Ringgaard, Steffen;

    2007-01-01

    . The dual-frequency method for estimation of parallel conductance failed to produce V(CC) that correlated with V(MRI). We conclude that selection of the calibration procedure for the CC has significant implications for the accuracy and precision of volume estimation and pressure-volume loop...

  13. Prediction of free-volume-type correlations in glassy chalcogenides from positron annihilation lifetime measurements

    Energy Technology Data Exchange (ETDEWEB)

    Shpotyuk, O., E-mail: shpotyuk@novas.lviv.ua [Institute of Materials of SRC “Carat”, 212 Stryjska Str., Lviv 79031 (Ukraine); Institute of Physics of Jan Dlugosz University, 13/15 al. Armii Krajowej, Czestcochowa 42200 (Poland); Ingram, A. [Opole University of Technology, 75 Ozimska Str., Opole 45370 (Poland); Shpotyuk, M. [Institute of Materials of SRC “Carat”, 212 Stryjska Str., Lviv 79031 (Ukraine); Lviv Polytechnic National University, 12 Bandery Str., Lviv 79013 (Ukraine); Filipecki, J. [Institute of Physics of Jan Dlugosz University, 13/15 al. Armii Krajowej, Czestcochowa 42200 (Poland)

    2014-11-01

    Highlights: • Decisive role of specific chemical environment in free-volume correlations in glass. • Realistic free volumes in As–S/Se glass are defined by newly modified τ{sub 2}-R formula. • Overestimated void sizes in chalcogenide glass as compared with molecular polymers. - Abstract: A newly modified correlation equation between defect-related positron lifetime determined within two-state trapping model and radius of corresponding free-volume-type defects was proposed to describe compositional variations in atomic-deficient structure of covalent-bonded chalcogenides like binary As–S/Se glasses. Specific chemical environment of free-volume voids around neighboring network-forming polyhedrons was shown to play a decisive role in this correlation, leading to systematically enhanced volumes in comparison with typical molecular substrates, such as polymers.

  14. Long-term measurements of particle number size distributions and the relationships with air mass history and source apportionment in the summer of Beijing

    Science.gov (United States)

    Wang, Z. B.; Hu, M.; Wu, Z. J.; Yue, D. L.; He, L. Y.; Huang, X. F.; Liu, X. G.; Wiedensohler, A.

    2013-10-01

    A series of long-term and temporary measurements were conducted to study the improvement of air quality in Beijing during the Olympic Games period (8-24 August 2008). To evaluate actions taken to improve the air quality, comparisons of particle number and volume size distributions of August 2008 and 2004-2007 were performed. The total particle number and volume concentrations were 14 000 cm-3 and 37 μm-3 cm-3 in August of 2008, respectively. These were reductions of 41% and 35% compared with mean values of August 2004-2007. A cluster analysis on air mass history and source apportionment were performed, exploring reasons for the reduction of particle concentrations. Back trajectories were classified into five major clusters. Air masses from the south direction are always associated with pollution events during the summertime in Beijing. In August 2008, the frequency of air mass arriving from the south was 1.3 times higher compared to the average of the previous years, which however did not result in elevated particle volume concentrations in Beijing. Therefore, the reduced particle number and volume concentrations during the 2008 Beijing Olympic Games cannot be only explained by meteorological conditions. Four factors were found influencing particle concentrations using a positive matrix factorization (PMF) model. They were identified as local and remote traffic emissions, combustion sources as well as secondary transformation. The reductions of the four sources were calculated to 47%, 44%, 43% and 30%, respectively. The significant reductions of particle number and volume concentrations may attribute to actions taken, focusing on primary emissions, especially related to the traffic and combustion sources.

  15. Surface area and volume measurements of volcanic ash particles by SEM stereoscopic imaging

    Science.gov (United States)

    Ersoy, Orkun

    2010-05-01

    Surface area of volcanic ash particles is of great importance to research including plume dynamics, particle chemical and water reactions in the plume, modelling (i.e. plume shape, particle interactions , dispersion etc.), remote sensing of transport and SO2, HCl, H2O, CO2 levels, forecasting plume location, and transportation and deposition of ash particles. The implemented method presented in this study offer new insights for surface characterization of volcanic ash particles on macro-pore regions. Surface area and volumes of volcanic ash particles were measured using digital elevation models (DEM) reconstructed from stereoscopic images acquired from different angles by scanning electron microscope (SEM). The method was tested using glycidyl methacrylate (GMA) micro-spheres which exhibit low spherical imperfections. The differences between measured and geometrically calculated surface areas were introduced for both micro-spheres and volcanic ash particles in order to highlight the probable errors in modelling on volcanic ash behaviour. The specific surface areas of volcanic ash particles using this method are reduced by half (from mean values of 0.045 m2/g to 0.021 m2/g) for the size increment 63 μm to 125 μm. Ash particles mostly have higher specific surface area values than the geometric forms irrespective of particle size. The specific surface area trends of spheres and ash particles resemble for finer particles (63 μm). Approximation to sphere and ellipsoid have similar margin of error for coarser particles (125 μm) but both seem to be inadequate for representation of real ash surfaces