Refining economics of U.S. gasoline: octane ratings and ethanol content.

Science.gov (United States)

Hirshfeld, David S; Kolb, Jeffrey A; Anderson, James E; Studzinski, William; Frusti, James

2014-10-07

Increasing the octane rating of the U.S. gasoline pool (currently ∼ 93 Research Octane Number (RON)) would enable higher engine efficiency for light-duty vehicles (e.g., through higher compression ratio), facilitating compliance with federal fuel economy and greenhouse gas (GHG) emissions standards. The federal Renewable Fuels Standard calls for increased renewable fuel use in U.S. gasoline, primarily ethanol, a high-octane gasoline component. Linear programming modeling of the U.S. refining sector was used to assess the effects on refining economics, CO2 emissions, and crude oil use of increasing average octane rating by increasing (i) the octane rating of refinery-produced hydrocarbon blendstocks for oxygenate blending (BOBs) and (ii) the volume fraction (Exx) of ethanol in finished gasoline. The analysis indicated the refining sector could produce BOBs yielding finished E20 and E30 gasolines with higher octane ratings at modest additional refining cost, for example, ∼ 1¢/gal for 95-RON E20 or 97-RON E30, and 3-5¢/gal for 95-RON E10, 98-RON E20, or 100-RON E30. Reduced BOB volume (from displacement by ethanol) and lower BOB octane could (i) lower refinery CO2 emissions (e.g., ∼ 3% for 98-RON E20, ∼ 10% for 100-RON E30) and (ii) reduce crude oil use (e.g., ∼ 3% for 98-RON E20, ∼ 8% for 100-RON E30).

40 CFR 80.240 - What are the small refiner gasoline sulfur standards?

Science.gov (United States)

2010-07-01

... volume of gasoline produced by a small refiner's refinery up to the lesser of: (i) 105% of the baseline gasoline volume as determined under § 80.250(a)(1); or (ii) The volume of gasoline produced at that... 40 Protection of Environment 16 2010-07-01 2010-07-01 false What are the small refiner gasoline...

European refining trends to 2030: The advent of multi-area linear programming

International Nuclear Information System (INIS)

Saint-Antonin, V.; Marion, P.

2011-01-01

The current high degree of uncertainty that pervades the global energy landscape is directly impacting on the oil industry, which is having to integrate growing mobility requirements in the context of energy transition due to the emergence of alternatives to petroleum fuels and restrictions on pollutant emissions. In this context, the study 'Raffinage 2030' (Refining 2030), carried out by IFPEN (the French Institute of Petroleum and New Energy Sources), is a prospective exercise for a better understanding of the balance between global supply and demand of petroleum products in order to shed light on the type and geographical location of necessary investments in refineries, as well as to assess the impact on these of the introduction of new fuels and more and more restrictions, such as environmental regulations. To this end, the refinery model used is one of linear programming, breaking the world down into nine geographical areas. This article introduces the programming model and its basic assumptions, before presenting the main lessons drawn om this study regarding the potential evolutions of the refining industry, in particular the European one, to face the market's long term trends. (authors)

AHRQ series paper 3: identifying, selecting, and refining topics for comparative effectiveness systematic reviews: AHRQ and the effective health-care program.

Science.gov (United States)

Whitlock, Evelyn P; Lopez, Sarah A; Chang, Stephanie; Helfand, Mark; Eder, Michelle; Floyd, Nicole

2010-05-01

This article discusses the identification, selection, and refinement of topics for comparative effectiveness systematic reviews within the Agency for Healthcare Research and Quality's Effective Health Care (EHC) program. The EHC program seeks to align its research topic selection with the overall goals of the program, impartially and consistently apply predefined criteria to potential topics, involve stakeholders to identify high-priority topics, be transparent and accountable, and continually evaluate and improve processes. A topic prioritization group representing stakeholder and scientific perspectives evaluates topic nominations that fit within the EHC program (are "appropriate") to determine how "important" topics are as considered against seven criteria. The group then judges whether a new comparative effectiveness systematic review would be a duplication of existing research syntheses, and if not duplicative, if there is adequate type and volume of research to conduct a new systematic review. Finally, the group considers the "potential value and impact" of a comparative effectiveness systematic review. As the EHC program develops, ongoing challenges include ensuring the program addresses truly unmet needs for synthesized research because national and international efforts in this arena are uncoordinated, as well as engaging a range of stakeholders in program decisions while also achieving efficiency and timeliness.

Element Partition Trees For H-Refined Meshes to Optimize Direct Solver Performance. Part I: Dynamic Programming

KAUST Repository

AbouEisha, Hassan M.

2017-07-13

We consider a class of two-and three-dimensional h-refined meshes generated by an adaptive finite element method. We introduce an element partition tree, which controls the execution of the multi-frontal solver algorithm over these refined grids. We propose and study algorithms with polynomial computational cost for the optimization of these element partition trees. The trees provide an ordering for the elimination of unknowns. The algorithms automatically optimize the element partition trees using extensions of dynamic programming. The construction of the trees by the dynamic programming approach is expensive. These generated trees cannot be used in practice, but rather utilized as a learning tool to propose fast heuristic algorithms. In this first part of our paper we focus on the dynamic programming approach, and draw a sketch of the heuristic algorithm. The second part will be devoted to a more detailed analysis of the heuristic algorithm extended for the case of hp-adaptive

Element Partition Trees For H-Refined Meshes to Optimize Direct Solver Performance. Part I: Dynamic Programming

KAUST Repository

AbouEisha, Hassan M.; Calo, Victor Manuel; Jopek, Konrad; Moshkov, Mikhail; Paszyńka, Anna; Paszyński, Maciej; Skotniczny, Marcin

2017-01-01

We consider a class of two-and three-dimensional h-refined meshes generated by an adaptive finite element method. We introduce an element partition tree, which controls the execution of the multi-frontal solver algorithm over these refined grids. We propose and study algorithms with polynomial computational cost for the optimization of these element partition trees. The trees provide an ordering for the elimination of unknowns. The algorithms automatically optimize the element partition trees using extensions of dynamic programming. The construction of the trees by the dynamic programming approach is expensive. These generated trees cannot be used in practice, but rather utilized as a learning tool to propose fast heuristic algorithms. In this first part of our paper we focus on the dynamic programming approach, and draw a sketch of the heuristic algorithm. The second part will be devoted to a more detailed analysis of the heuristic algorithm extended for the case of hp-adaptive

Refinement Types for TypeScript

OpenAIRE

Vekris, Panagiotis; Cosman, Benjamin; Jhala, Ranjit

2016-01-01

We present Refined TypeScript (RSC), a lightweight refinement type system for TypeScript, that enables static verification of higher-order, imperative programs. We develop a formal core of RSC that delineates the interaction between refinement types and mutability. Next, we extend the core to account for the imperative and dynamic features of TypeScript. Finally, we evaluate RSC on a set of real world benchmarks, including parts of the Octane benchmarks, D3, Transducers, and the TypeScript co...

Correction volumes and densities in Vitrea Program

International Nuclear Information System (INIS)

Abrantes, Marcos E.S.; Oliveira, A.H. de

2014-01-01

Introduction: with the increased use of 3D reconstruction techniques to assist in diagnosis, Vitrea® program is widely used. To use this program you need to know the correction values to generate the volumes and number of real CT human tissues. Objective: provide correction values for volumes and number of CT, read the Vitrea program, of the tissues generated by DICOM images from CT. Methodology: this study used a PMMA chest phantom to generate the DICOM images on a scanner. To check the calibration of the scanner was used Catphan phantom and compared the manufacturer of the values associated with its straight linearity. Results: the volume of PMMA phantom was of 11166.58 cm³ and CT number (123.5 ± 33.4) UH. For the volume found in Vitrea program, according to the structures of interest, were 11897.29 cm 3 , 10901.65 cm³, 16906.49 cm 3 and 11848.34 cm³ and corrections values are -6.14%, + 2.43% -6.94% -5.75% respectively for the tissues: lung, bone, soft and full. For the CT numbers found in this program were (97.60 ± 58.9) UH, (72.00 ± 176.00) UH, (143.20 ± 19.50) UH and (31.90 ± 239,10) UH and corrections of + 26.54%, + 71.53%, -13.64% and 387.15% respectively for tissues: lung, bone, soft and full. Conclusion: the procedure performed can be used in other 3D reconstruction programs and where there are tools to reading CT number, observing the necessary corrections

Highway Safety Program Manual: Volume 3: Motorcycle Safety.

Science.gov (United States)

National Highway Traffic Safety Administration (DOT), Washington, DC.

Volume 3 of the 19-volume Highway Safety Program Manual (which provides guidance to State and local governments on preferred highway safety practices) concentrates on aspects of motorcycle safety. The purpose and specific objectives of a State motorcycle safety program are outlined. Federal authority in the highway safety area and general policies…

Refinement in Z and Object-Z foundations and advanced applications

CERN Document Server

Derrick, John

2013-01-01

Refinement is one of the cornerstones of the formal approach to software engineering, and its use in various domains has led to research on new applications and generalisation. This book brings together this important research in one volume, with the addition of examples drawn from different application areas. It covers four main themes:Data refinement and its application to ZGeneralisations of refinement that change the interface and atomicity of operationsRefinement in Object-ZModelling state and behaviour by combining Object-Z with CSPRefinement in Z and Object-Z: Foundations and Advanced A

Petroleum movements and investments in the refining industry: The impact of worldwide environmental regulations

International Nuclear Information System (INIS)

Guariguata U., G.

1995-01-01

Since the enactment of the US Clean Air Act Amendments of 1990, the worldwide refining industry has aligned itself to become increasing attuned to the future well-being of the environment. Refiners must now develop strategies which address careful selection of crude slates, significant increases and changes in product movements, and upgrading of facilities to meet growing demand--in short, strategies which allow them to make substantial increases in capital investments. The objective of this paper is to determine the regional capital investments refiners must make in order to comply with environmental legislation. The methodology in making this determination was founded on a comprehensive analysis of worldwide petroleum supply/demand and distribution patterns for the coming five years, and included evaluation of a set of linear programming (LP) models based on forecasts for regional product demands and projections of regional specifications. The models considered two scenarios, in which either (1) refinery expansion occurs chiefly in the market consuming regions, or (2) crude producers take control of incremental crude volumes and further expand their planned refining projects and the marketing of refined products. The results of these models, coupled with an understanding of geopolitical situations and economic analyses, provided estimates for capital expenditures for the coming decade. In specific, the following issues were addressed, and are discussed in this paper: refined product trade outlook; crude supply; crude quality; shipping; and capital investments

Anomalies in the refinement of isoleucine

International Nuclear Information System (INIS)

Berntsen, Karen R. M.; Vriend, Gert

2014-01-01

The side-chain torsion angles of isoleucines in X-ray protein structures are a function of resolution, secondary structure and refinement software. Detailing the standard torsion angles used in refinement software can improve protein structure refinement. A study of isoleucines in protein structures solved using X-ray crystallography revealed a series of systematic trends for the two side-chain torsion angles χ 1 and χ 2 dependent on the resolution, secondary structure and refinement software used. The average torsion angles for the nine rotamers were similar in high-resolution structures solved using either the REFMAC, CNS or PHENIX software. However, at low resolution these programs often refine towards somewhat different χ 1 and χ 2 values. Small systematic differences can be observed between refinement software that uses molecular dynamics-type energy terms (for example CNS) and software that does not use these terms (for example REFMAC). Detailing the standard torsion angles used in refinement software can improve the refinement of protein structures. The target values in the molecular dynamics-type energy functions can also be improved

Anomalies in the refinement of isoleucine

Energy Technology Data Exchange (ETDEWEB)

Berntsen, Karen R. M.; Vriend, Gert, E-mail: gerrit.vriend@radboudumc.nl [Radboud University Medical Center, Geert Grooteplein 26-28, 6525 GA Nijmegen (Netherlands)

2014-04-01

The side-chain torsion angles of isoleucines in X-ray protein structures are a function of resolution, secondary structure and refinement software. Detailing the standard torsion angles used in refinement software can improve protein structure refinement. A study of isoleucines in protein structures solved using X-ray crystallography revealed a series of systematic trends for the two side-chain torsion angles χ{sub 1} and χ{sub 2} dependent on the resolution, secondary structure and refinement software used. The average torsion angles for the nine rotamers were similar in high-resolution structures solved using either the REFMAC, CNS or PHENIX software. However, at low resolution these programs often refine towards somewhat different χ{sub 1} and χ{sub 2} values. Small systematic differences can be observed between refinement software that uses molecular dynamics-type energy terms (for example CNS) and software that does not use these terms (for example REFMAC). Detailing the standard torsion angles used in refinement software can improve the refinement of protein structures. The target values in the molecular dynamics-type energy functions can also be improved.

Dynamic Programming Algorithm for Generation of Optimal Elimination Trees for Multi-frontal Direct Solver Over H-refined Grids

KAUST Repository

AbouEisha, Hassan M.; Moshkov, Mikhail; Calo, Victor M.; Paszynski, Maciej; Goik, Damian; Jopek, Konrad

2014-01-01

In this paper we present a dynamic programming algorithm for finding optimal elimination trees for computational grids refined towards point or edge singularities. The elimination tree is utilized to guide the multi-frontal direct solver algorithm

Energy-efficient buildings program evaluations. Volume 2: Evaluation summaries

Energy Technology Data Exchange (ETDEWEB)

Lee, A.D.; Mayi, D.; Edgemon, S.D.

1997-04-01

This document presents summaries of code and utility building program evaluations reviewed as the basis for the information presented in Energy-Efficient Buildings Program Evaluations, Volume 1: Findings and Recommendations, DOE/EE/OBT-11569, Vol. 1. The main purpose of this volume is to summarize information from prior evaluations of similar programs that may be useful background for designing and conducting an evaluation of the BSGP. Another purpose is to summarize an extensive set of relevant evaluations and provide a resource for program designers, mangers, and evaluators.

Refining SCJ Mission Specifications into Parallel Handler Designs

Directory of Open Access Journals (Sweden)

Frank Zeyda

2013-05-01

Full Text Available Safety-Critical Java (SCJ is a recent technology that restricts the execution and memory model of Java in such a way that applications can be statically analysed and certified for their real-time properties and safe use of memory. Our interest is in the development of comprehensive and sound techniques for the formal specification, refinement, design, and implementation of SCJ programs, using a correct-by-construction approach. As part of this work, we present here an account of laws and patterns that are of general use for the refinement of SCJ mission specifications into designs of parallel handlers used in the SCJ programming paradigm. Our notation is a combination of languages from the Circus family, supporting state-rich reactive models with the addition of class objects and real-time properties. Our work is a first step to elicit laws of programming for SCJ and fits into a refinement strategy that we have developed previously to derive SCJ programs.

OCCUPATIONAL EDUCATION--PLANNING AND PROGRAMMING. VOLUME TWO.

Science.gov (United States)

KOTZ, ARNOLD

ADDITIONAL POSITION PAPERS BASED ON INFORMATION GATHERED IN THE RECONNAISSANCE SURVEYS OF PLANNING AND PROGRAMING IN OCCUPATIONAL EDUCATION, REPORTED IN VOLUME ONE (VT 005 041), ARE PRESENTED. PART IV, CONCERNED WITH PROGRAM STRUCTURE AND BUDGETING AND THEIR RELATION TO THE PLANNING PROCESS, INCLUDES THE PAPERS--(1) "CURRENT POLICIES AND…

Implementing US Department of Energy lessons learned programs. Volume 2

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-08-01

The DOE Lessons Learned Handbook is a two-volume publication developed to supplement the DOE Lessons Learned Standard (DOE-STD-7501-95) with information that will organizations in developing or improving their lessons learned programs. Volume 1 includes greater detail than the Standard in areas such as identification and documentation of lessons learned; it also contains sections on specific processes such as training and performance measurement. Volume 2 (this document) contains examples of program documents developed by existing lessons learned programs as well as communications material, functional categories, transmittal documents, sources of professional and industry lessons learned, and frequently asked questions about the Lessons Learned List Service.

Refining of raw materials, lignite present economic problems

Energy Technology Data Exchange (ETDEWEB)

Schirmer, G.

1985-06-01

East Germany seeks an economic intensification program that involves refining raw materials to a higher level. Lignite briquetting prior to liquefaction and gasification illustrates both the theoretical and practical aspects of that goal and also introduces questions of secure supplies. The author describes the special labor processes, use of technology, recycling of waste materials, and other new problems that the approach entails as the refined raw materials become new materials or energy sources. Economics based on the value of the refined product and the cost of the materials determine the degree of refinement. The concept also involves the relationship of producer and user as profits increase.

International Nuclear Model. Volume 3. Program description

International Nuclear Information System (INIS)

Andress, D.

1985-01-01

This is Volume 3 of three volumes of documentation of the International Nuclear Model (INM). This volume presents the Program Description of the International Nuclear Model, which was developed for the Nuclear and Alternate Fuels Division (NAFD), Office of Coal, Nuclear, Electric and Alternate Fuels, Energy Information Administration (EIA), US Department of Energy (DOE). The International Nuclear Model (INM) is a comprehensive model of the commercial nuclear power industry. It simulates economic decisions for reactor deployment and fuel management decision based on an input set of technical economic and scenario parameters. The technical parameters include reactor operating characteristics, fuel cycle timing and mass loss factors, and enrichment tails assays. Economic parameters include fuel cycle costs, financial data, and tax alternatives. INM has a broad range of scenario options covering, for example, process constraints, interregional activities, reprocessing, and fuel management selection. INM reports reactor deployment schedules, electricity generation, and fuel cycle requirements and costs. It also has specialized reports for extended burnup and permanent disposal. Companion volumes to Volume 3 are: Volume 1 - Model Overview, and Volume 2 - Data Base Relationships

On mesh refinement and accuracy of numerical solutions

NARCIS (Netherlands)

Zhou, Hong; Peters, Maria; van Oosterom, Adriaan

1993-01-01

This paper investigates mesh refinement and its relation with the accuracy of the boundary element method (BEM) and the finite element method (FEM). TO this end an isotropic homogeneous spherical volume conductor, for which the analytical solution is available, wag used. The numerical results

40 CFR 80.340 - What standards and requirements apply to refiners producing gasoline by blending blendstocks into...

Science.gov (United States)

2010-07-01

... to refiners producing gasoline by blending blendstocks into previously certified gasoline (PCG)? 80... gasoline by blending blendstocks into previously certified gasoline (PCG)? (a) Any refiner who produces...) The sulfur content and volume of each batch of gasoline produced is that of the butane the refiner...

Nuclear proliferation and civilian nuclear power: report of the Nonproliferation Alternative Systems Assessment Program. Volume 1. Program summary

Energy Technology Data Exchange (ETDEWEB)

1979-12-01

This report summarizes the Nonproliferation Alternative Systems Assessment Program (NASAP): its background, its studies, and its results. This introductory chapter traces the growth of the issue of nuclear weapons proliferation and the organization and objectives of NASAP. Chapter 2 summarizes the program's assessments, findings and recommendations. Each of Volumes II-VII reports on an individual assessment (Volume II: Proliferation Resistance; Volume III: Resources and Fuel Cycle Facilities; Volume IV: Commercial Potential; Volume V: Economics and Systems Analysis; Volume VI: Safety and Environmental Considerations for Licensing; Volume VII: International Perspectives). Volume VIII (Advanced Concepts) presents a combined assessment of several less fully developed concepts, and Volume IX (Reactor and Fuel Cycle Descriptions) provides detailed descriptions of the reactor and fuel-cycle systems studied by NASAP.

Nuclear proliferation and civilian nuclear power: report of the Nonproliferation Alternative Systems Assessment Program. Volume 1. Program summary

International Nuclear Information System (INIS)

1979-12-01

This report summarizes the Nonproliferation Alternative Systems Assessment Program (NASAP): its background, its studies, and its results. This introductory chapter traces the growth of the issue of nuclear weapons proliferation and the organization and objectives of NASAP. Chapter 2 summarizes the program's assessments, findings and recommendations. Each of Volumes II-VII reports on an individual assessment (Volume II: Proliferation Resistance; Volume III: Resources and Fuel Cycle Facilities; Volume IV: Commercial Potential; Volume V: Economics and Systems Analysis; Volume VI: Safety and Environmental Considerations for Licensing; Volume VII: International Perspectives). Volume VIII (Advanced Concepts) presents a combined assessment of several less fully developed concepts, and Volume IX (Reactor and Fuel Cycle Descriptions) provides detailed descriptions of the reactor and fuel-cycle systems studied by NASAP

New Process for Grain Refinement of Aluminum. Final Report

Energy Technology Data Exchange (ETDEWEB)

Dr. Joseph A. Megy

2000-09-22

A new method of grain refining aluminum involving in-situ formation of boride nuclei in molten aluminum just prior to casting has been developed in the subject DOE program over the last thirty months by a team consisting of JDC, Inc., Alcoa Technical Center, GRAS, Inc., Touchstone Labs, and GKS Engineering Services. The Manufacturing process to make boron trichloride for grain refining is much simpler than preparing conventional grain refiners, with attendant environmental, capital, and energy savings. The manufacture of boride grain refining nuclei using the fy-Gem process avoids clusters, salt and oxide inclusions that cause quality problems in aluminum today.

Fetching and Parsing Data from the Web with OpenRefine

Directory of Open Access Journals (Sweden)

Evan Peter Williamson

2017-08-01

Full Text Available OpenRefine is a powerful tool for exploring, cleaning, and transforming data. An earlier Programming Historian lesson, “Cleaning Data with OpenRefine”, introduced the basic functionality of Refine to efficiently discover and correct inconsistency in a data set. Building on those essential data wrangling skills, this lesson focuses on Refine’s ability to fetch URLs and parse web content. Examples introduce some of the advanced features to transform and enhance a data set including: - fetch URLs using Refine - construct URL queries to retrieve information from a simple web API - parse HTML and JSON responses to extract relevant data - use array functions to manipulate string values - use Jython to extend Refine’s functionality It will be helpful to have basic familiarity with OpenRefine, HTML, and programming concepts such as variables and loops to complete this lesson.

Nuclear proliferation and civilian nuclear power. Report of the Nonproliferation Alternative Systems Assessment Program. Volume I. Program summary

International Nuclear Information System (INIS)

1980-06-01

This report summarizes the Nonproliferation Alternative Systems Assessment Program (NASAP): its background, its studies, and its results. The introductory chapter traces the growth of the issue of nuclear weapons proliferation and the organization and objectives of NASAP. Chapter 2 summarizes the program's assessments, findings, and recommendations. Each of Volumes II-VII reports on an individual assessment (Volumn II: Proliferation Resistance; Volume III: Resources and Fuel Cycle Facilities; Volume IV: Commercial Potential; Volume V: Economics and Systems Analysis; Volume VI: Safety and Environmental Considerations for Licensing; Volume VII: International Perspectives). Volume VIII (Advanced Concepts) presents a combined assessment of several less fully developed concepts, and Volume IX (Reactor and Fuel Cycle Descriptions) provides detailed descriptions of the reactor and fuel-cycle systems studied by NASAP

Laser program annual report, 1977. Volume 2

International Nuclear Information System (INIS)

Bender, C.F.; Jarman, B.D.

1978-07-01

This volume contains detailed information on each of the following sections: (1) fusion target design, (2) target fabrication, (3) laser fusion experiments and analysis, (4) advanced lasers, (5) systems and applications studies, and (6) laser isotope separation program

Constellation Program: Lessons Learned. Volume 1; Executive Summary

Science.gov (United States)

Rhatigan, Jennifer L. (Editor)

2011-01-01

This document (Volume I) provides an executive summary of the lessons learned from the Constellation Program. A companion Volume II provides more detailed analyses for those seeking further insight and information. In this volume, Section 1.0 introduces the approach in preparing and organizing the content to enable rapid assimilation of the lessons. Section 2.0 describes the contextual framework in which the Constellation Program was formulated and functioned that is necessary to understand most of the lessons. Context of a former program may seem irrelevant in the heady days of new program formulation. However, readers should take some time to understand the context. Many of the lessons would be different in a different context, so the reader should reflect on the similarities and differences in his or her current circumstances. Section 3.0 summarizes key findings developed from the significant lessons learned at the program level that appear in Section 4.0. Readers can use the key findings in Section 3.0 to peruse for particular topics, and will find more supporting detail and analyses in Section 4.0 in a topical format. Appendix A contains a white paper describing the Constellation Program formulation that may be of use to readers wanting more context or background information. The reader will no doubt recognize some very similar themes from previous lessons learned, blue-ribbon committee reviews, National Academy reviews, and advisory panel reviews for this and other large-scale human spaceflight programs; including Apollo, Space Shuttle, Shuttle/Mir, and the ISS. This could represent an inability to learn lessons from previous generations; however, it is more likely that similar challenges persist in the Agency structure and approach to program formulation, budget advocacy, and management. Perhaps the greatest value of these Constellation lessons learned can be found in viewing them in context with these previous efforts to guide and advise the Agency and its

Laser program annual report, 1977. Volume 2

Energy Technology Data Exchange (ETDEWEB)

Bender, C.F.; Jarman, B.D. (eds.)

1978-07-01

This volume contains detailed information on each of the following sections: (1) fusion target design, (2) target fabrication, (3) laser fusion experiments and analysis, (4) advanced lasers, (5) systems and applications studies, and (6) laser isotope separation program. (MOW)

Method of optimization of the natural gas refining process

Energy Technology Data Exchange (ETDEWEB)

Sadykh-Zade, E.S.; Bagirov, A.A.; Mardakhayev, I.M.; Razamat, M.S.; Tagiyev, V.G.

1980-01-01

The SATUM (automatic control system of technical operations) system introduced at the Shatlyk field should assure good quality of gas refining. In order to optimize the natural gas refining processes and experimental-analytical method is used in compiling the mathematical descriptions. The program, compiled in Fortran language, in addition to parameters of optimal conditions gives information on the yield of concentrate and water, concentration and consumption of DEG, composition and characteristics of the gas and condensate. The algorithm for calculating optimum engineering conditions of gas refining is proposed to be used in ''advice'' mode, and also for monitoring progress of the gas refining process.

Synfuel program analysis. Volume 2: VENVAL users manual

Science.gov (United States)

Muddiman, J. B.; Whelan, J. W.

1980-07-01

This volume is intended for program analysts and is a users manual for the VENVAL model. It contains specific explanations as to input data requirements and programming procedures for the use of this model. VENVAL is a generalized computer program to aid in evaluation of prospective private sector production ventures. The program can project interrelated values of installed capacity, production, sales revenue, operating costs, depreciation, investment, dent, earnings, taxes, return on investment, depletion, and cash flow measures. It can also compute related public sector and other external costs and revenues if unit costs are furnished.

Pacific Basin Heavy Oil Refining Capacity

Directory of Open Access Journals (Sweden)

David Hackett

2013-02-01

Full Text Available The United States today is Canada’s largest customer for oil and refined oil products. However, this relationship may be strained due to physical, economic and political influences. Pipeline capacity is approaching its limits; Canadian oil is selling at substantive discounts to world market prices; and U.S. demand for crude oil and finished products (such as gasoline, has begun to flatten significantly relative to historical rates. Lower demand, combined with increased shale oil production, means U.S. demand for Canadian oil is expected to continue to decline. Under these circumstances, gaining access to new markets such as those in the Asia-Pacific region is becoming more and more important for the Canadian economy. However, expanding pipeline capacity to the Pacific via the proposed Northern Gateway pipeline and the planned Trans Mountain pipeline expansion is only feasible when there is sufficient demand and processing capacity to support Canadian crude blends. Canadian heavy oil requires more refining and produces less valuable end products than other lighter and sweeter blends. Canadian producers must compete with lighter, sweeter oils from the Middle East, and elsewhere, for a place in the Pacific Basin refineries built to handle heavy crude blends. Canadian oil sands producers are currently expanding production capacity. Once complete, the Northern Gateway pipeline and the Trans Mountain expansion are expected to deliver an additional 500,000 to 1.1 million barrels a day to tankers on the Pacific coast. Through this survey of the capacity of Pacific Basin refineries, including existing and proposed facilities, we have concluded that there is sufficient technical capacity in the Pacific Basin to refine the additional Canadian volume; however, there may be some modifications required to certain refineries to allow them to process Western Canadian crude. Any additional capacity for Canadian oil would require refinery modifications or

Diversion Path Analysis handbook. Volume 4 (of 4 volumes). Computer Program 2

International Nuclear Information System (INIS)

Schleter, J.C.

1978-11-01

The FORTRAN IV computer program, DPA Computer Program 2 (DPACP-2) is used to produce tables and statistics on modifications identified when performing a Diversion Path Analysis (DPA) in accord with the methodology given in Volume 1. The program requires 259088 bytes exclusive of the operating system. The data assembled and tabulated by DPACP-2 assist the DPA team in analyzing and evaluating modifications to the plant's safeguards system that would eliminate, or reduce the severity of, vulnerabilities identified by means of the DPA. These vulnerabilities relate to the capability of the plant's material control and material accounting subsystems to indicate diversion of special nuclear material (SNM) by a knowledgeable insider

Cleaning Data with OpenRefine

Directory of Open Access Journals (Sweden)

Seth van Hooland

2013-08-01

Full Text Available Duplicate records, empty values and inconsistent formats are phenomena we should be prepared to deal with when using historical data sets. This lesson will teach you how to discover inconsistencies in data contained within a spreadsheet or a database. As we increasingly share, aggregate and reuse data on the web, historians will need to respond to data quality issues which inevitably pop up. Using a program called OpenRefine, you will be able to easily identify systematic errors such as blank cells, duplicates, spelling inconsistencies, etc. OpenRefine not only allows you to quickly diagnose the accuracy of your data, but also to act upon certain errors in an automated manner.

MOD-5A wind turbine generator program design report: Volume 1: Executive Summary

Science.gov (United States)

1984-01-01

The design, development and analysis of the 7.3 MW MOD-5A wind turbine generator covering work performed between July 1980 and June 1984 is discussed. The report is divided into four volumes: Volume 1 summarizes the entire MOD-5A program, Volume 2 discusses the conceptual and preliminary design phases, Volume 3 describes the final design of the MOD-5A, and Volume 4 contains the drawings and specifications developed for the final design. Volume 1, the Executive Summary, summarizes all phases of the MOD-5A program. The performance and cost of energy generated by the MOD-5A are presented. Each subsystem - the rotor, drivetrain, nacelle, tower and foundation, power generation, and control and instrumentation subsystems - is described briefly. The early phases of the MOD-5A program, during which the design was analyzed and optimized, and new technologies and materials were developed, are discussed. Manufacturing, quality assurance, and safety plans are presented. The volume concludes with an index of volumes 2 and 3.

Development of a Refined Staff Group Trainer

National Research Council Canada - National Science Library

Quensel, Susan

1999-01-01

.... As a follow-on effort to the previous SGT project, the goal was to refine a brigade-level staff training program to more effectively and efficiently coordinate the activities within and between the...

Selection methodology for LWR safety programs and proposals. Volume 2. Methodology application

International Nuclear Information System (INIS)

Ritzman, R.L.; Husseiny, A.A.

1980-08-01

The results of work done to update and apply a methodology for selecting (prioritizing) LWR safety technology R and D programs are described. The methodology is based on multiattribute utility (MAU) theory. Application of the methodology to rank-order a group of specific R and D programs included development of a complete set of attribute utility functions, specification of individual attribute scaling constants, and refinement and use of an interactive computer program (MAUP) to process decision-maker inputs and generate overall (multiattribute) program utility values. The output results from several decision-makers are examined for consistency and conclusions and recommendations regarding general use of the methodology are presented. 3 figures, 18 tables

Highly Insulating Windows Volume Purchase Program Final Report

Energy Technology Data Exchange (ETDEWEB)

None

2013-04-01

This report documents the development, execution outcomes and lessons learned of the Highly Insulating Windows Volume Purchase (WVP) Program carried out over a three-year period from 2009 through 2012. The primary goals of the program were met: 1) reduce the incremental cost of highly insulating windows compared to ENERGY STAR windows; and 2) raise the public and potential buyers’ awareness of highly insulating windows and their benefits. A key outcome of the program is that the 2013 ENERGY STAR Most Efficient criteria for primary residential windows were adopted from the technical specifications set forth in the WVP program.

Highway Safety Program Manual: Volume 8: Alcohol in Relation to Highway Safety.

Science.gov (United States)

National Highway Traffic Safety Administration (DOT), Washington, DC.

Volume 8 of the 19-volume Highway Safety Program Manual (which provides guidance to State and local governments on preferred highway safety practices) concentrates on alcohol in relation to highway safety. The purpose and objectives of the alcohol program are outlined. Federal authority in the area of highway safety and general policies regarding…

Genomic multiple sequence alignments: refinement using a genetic algorithm

Directory of Open Access Journals (Sweden)

Lefkowitz Elliot J

2005-08-01

Full Text Available Abstract Background Genomic sequence data cannot be fully appreciated in isolation. Comparative genomics – the practice of comparing genomic sequences from different species – plays an increasingly important role in understanding the genotypic differences between species that result in phenotypic differences as well as in revealing patterns of evolutionary relationships. One of the major challenges in comparative genomics is producing a high-quality alignment between two or more related genomic sequences. In recent years, a number of tools have been developed for aligning large genomic sequences. Most utilize heuristic strategies to identify a series of strong sequence similarities, which are then used as anchors to align the regions between the anchor points. The resulting alignment is globally correct, but in many cases is suboptimal locally. We describe a new program, GenAlignRefine, which improves the overall quality of global multiple alignments by using a genetic algorithm to improve local regions of alignment. Regions of low quality are identified, realigned using the program T-Coffee, and then refined using a genetic algorithm. Because a better COFFEE (Consistency based Objective Function For alignmEnt Evaluation score generally reflects greater alignment quality, the algorithm searches for an alignment that yields a better COFFEE score. To improve the intrinsic slowness of the genetic algorithm, GenAlignRefine was implemented as a parallel, cluster-based program. Results We tested the GenAlignRefine algorithm by running it on a Linux cluster to refine sequences from a simulation, as well as refine a multiple alignment of 15 Orthopoxvirus genomic sequences approximately 260,000 nucleotides in length that initially had been aligned by Multi-LAGAN. It took approximately 150 minutes for a 40-processor Linux cluster to optimize some 200 fuzzy (poorly aligned regions of the orthopoxvirus alignment. Overall sequence identity increased only

A logical approach to determine a waste segregation/volume reduction program

International Nuclear Information System (INIS)

Shriner, G.D.; Carmel, P.G.; Shimmura, H.

1986-01-01

This paper discusses advantages and disadvantages of hand sorting versus use of automated radioactive waste segregation monitors and makes an analysis of costs/versus benefits based on volume with time. Many programs to be employed to prevent unnecessary waste generation with little or no additional cost to the power plant. Parameters needed to perform a cost analysis and methods used to obtain them are discussed. Recommendations on use of vendor-supplied services for segregation, volume reduction, and decontamination are given. The data provided will enable the selection of a program(s) to benefit the individual user's requirements

TRU Waste Sampling Program: Volume I. Waste characterization

International Nuclear Information System (INIS)

Clements, T.L. Jr.; Kudera, D.E.

1985-09-01

Volume I of the TRU Waste Sampling Program report presents the waste characterization information obtained from sampling and characterizing various aged transuranic waste retrieved from storage at the Idaho National Engineering Laboratory and the Los Alamos National Laboratory. The data contained in this report include the results of gas sampling and gas generation, radiographic examinations, waste visual examination results, and waste compliance with the Waste Isolation Pilot Plant-Waste Acceptance Criteria (WIPP-WAC). A separate report, Volume II, contains data from the gas generation studies

A cellular automaton - finite volume method for the simulation of dendritic and eutectic growth in binary alloys using an adaptive mesh refinement

Science.gov (United States)

Dobravec, Tadej; Mavrič, Boštjan; Šarler, Božidar

2017-11-01

A two-dimensional model to simulate the dendritic and eutectic growth in binary alloys is developed. A cellular automaton method is adopted to track the movement of the solid-liquid interface. The diffusion equation is solved in the solid and liquid phases by using an explicit finite volume method. The computational domain is divided into square cells that can be hierarchically refined or coarsened using an adaptive mesh based on the quadtree algorithm. Such a mesh refines the regions of the domain near the solid-liquid interface, where the highest concentration gradients are observed. In the regions where the lowest concentration gradients are observed the cells are coarsened. The originality of the work is in the novel, adaptive approach to the efficient and accurate solution of the posed multiscale problem. The model is verified and assessed by comparison with the analytical results of the Lipton-Glicksman-Kurz model for the steady growth of a dendrite tip and the Jackson-Hunt model for regular eutectic growth. Several examples of typical microstructures are simulated and the features of the method as well as further developments are discussed.

Government will shape China's refining boom

International Nuclear Information System (INIS)

Wang, H.

1995-01-01

China's refining system is undergoing a major overhaul. New refineries are being built as existing ones are upgraded and expanded. The success of refineries funded completely or partially by non-chinese companies will depend in part on Chinese government policy. There will be demand for products from third-party processing facilities, but hard current is necessary for the investors to repatriate profits and for china Petrochemical Corp. (Sinopec) to bid on the products from such facilities. The limited convertibility of chinese current constitutes a major central control over the country's entire economy. This control can be affected by limiting product exchange participants and the volumes to be traded. Such a limitation, however, will reduce access of non-Chinese companies to China's markets, and is not likely to occur in the next 10 years. The paper discusses the current situation in capacity and in refining, capacity, expansion, refinery planning, construction projects, third-party processing, and the prospects for change

Robust Refinement as Implemented in TOPAS

Energy Technology Data Exchange (ETDEWEB)

Stone, K.; Stephens, P

2010-01-01

A robust refinement procedure is implemented in the program TOPAS through an iterative reweighting of the data. Examples are given of the procedure as applied to fitting partially overlapped peaks by full and partial models and also of the structures of ibuprofen and acetaminophen in the presence of unmodeled impurity contributions

The development and refinement of models of less established and more established high school environmental service-learning programs in Florida

Science.gov (United States)

Malikova, Yuliya

2005-07-01

Environmental Service-Learning (Env. S-L) appears to show great promise and practitioners tout its benefits, although there have been fewer than ten studies in this emerging area of environmental education. The overall study purpose was to describe the nature, status, and effects of Grade 9--16 Env. S-L programs in Florida, and develop descriptive models of those programs. The purpose of Phase I was to describe these programs and associated partnerships. Based on Phase I results, the purpose of Phase II was to develop, compare, and refine models for less and more established high school programs. This study involved: (1) defining the population of Florida 9--16 Env. S-L programs (Phase I); (2) developing and administering program surveys (Phase I, quantitative); (3) analyzing Phase I survey data and identifications of options for Phase II (Intermediate stage); (4) designing and implementing methodology for further data collection (Phase II, qualitative); (5) refining and finalizing program models (Phase II, descriptive); and (6) summarizing program data, changes, and comparisons. This study revealed that Env. S-L has been practiced in a variety of ways at the high school and college levels in Florida. There, the number of high school programs, and participating teachers and students has been growing. Among others, major program features include block scheduling, indirect S-L activities, external funding sources, and formal and ongoing community partnerships. Findings based on self-reported program assessment results indicate that S-L has had positive effects on students across Furco's S-L outcome domains (i.e., academic achievement/success, school participation/behavior, carrier development, personal development, interpersonal development, ethical/moral development, and development of civic responsibility). Differences existed between less established and more established Env. S-L programs. Less established programs had relatively few participating teachers

Projections of the impact of expansion of domestic heavy oil production on the U.S. refining industry from 1990 to 2010. Topical report

Energy Technology Data Exchange (ETDEWEB)

Olsen, D.K.; Ramzel, E.B.; Strycker, A.R. [National Institute for Petroleum and Energy Research, Bartlesville, OK (United States). ITT Research Institute; Guariguata, G.; Salmen, F.G. [Bonner and Moore Management Science, Houston, TX (United States)

1994-12-01

This report is one of a series of publications assessing the feasibility of increasing domestic heavy oil (10{degrees} to 20{degrees} API gravity) production. This report provides a compendium of the United States refining industry and analyzes the industry by Petroleum Administration for Defense District (PADD) and by ten smaller refining areas. The refining capacity, oil source and oil quality are analyzed, and projections are made for the U.S. refining industry for the years 1990 to 2010. The study used publicly available data as background. A linear program model of the U.S. refining industry was constructed and validated using 1990 U.S. refinery performance. Projections of domestic oil production (decline) and import of crude oil (increases) were balanced to meet anticipated demand to establish a base case for years 1990 through 2010. The impact of additional domestic heavy oil production, (300 MB/D to 900 MB/D, originating in select areas of the U.S.) on the U.S. refining complex was evaluated. This heavy oil could reduce the import rate and the balance of payments by displacing some imported, principally Mid-east, medium crude. The construction cost for refining units to accommodate this additional domestic heavy oil production in both the low and high volume scenarios is about 7 billion dollars for bottoms conversion capacity (delayed coking) with about 50% of the cost attributed to compliance with the Clean Air Act Amendment of 1990.

International Photovoltaic Program Plan. Volume II. Appendices

Energy Technology Data Exchange (ETDEWEB)

Costello, D.; Koontz, R.; Posner, D.; Heiferling, P.; Carpenter, P.; Forman, S.; Perelman, L.

1979-12-01

This second volume of a two-part report on the International Photovoltaic Program Plan contains appendices summarizing the results of analyses conducted in preparation of the plan. These analyses include compilations of relevant statutes and existing Federal programs; strategies designed to expand the use of photovoltaics abroad; information on the domestic photovoltaic plan and its impact on the proposed international plan; perspectives on foreign competition; industry views on the international photovoltaic market and ideas about how US government actions could affect this market; international financing issues; and information on issues affecting foreign policy and developing countries.

Diversion Path Analysis handbook. Volume 3 (of 4 volumes). Computer Program 1

International Nuclear Information System (INIS)

Schleter, J.C.

1978-11-01

The FORTRAN IV computer program, DPA Computer Program 1 (DPACP-1), is used to assemble and tabulate the data for Specific Diversion Paths (SDPs) identified when performing a Diversion Path Analysis (DPA) in accord with the methodology given in Volume 1. The program requires 255498 bytes exclusive of the operating system. The data assembled and tabulated by DPACP-1 are used by the DPA team to assist in analyzing vulnerabilities, in a plant's material control and material accounting subsystems, to diversion of special nuclear material (SNM) by a knowledgable insider. Based on this analysis, the DPA team can identify, and propose to plant management, modifications to the plant's safeguards system that would eliminate, or reduce the severity of, the identified vulnerabilities. The data are also used by plant supervision when investigating a potential diversion

Refining revolution

Energy Technology Data Exchange (ETDEWEB)

Fesharaki, F.; Isaak, D.

1984-01-01

A review of changes in the oil refining industry since 1973 examines the drop in capacity use and its effect on profits of the Organization of Economic Cooperation and Development (OECD) countries compared to world refining. OPEC countries used their new oil revenues to expand Gulf refineries, which put additional pressure on OECD refiners. OPEC involvement in global marketing, however, could help to secure supplies. Scrapping some older OECD refineries could improve the percentage of capacity in use if new construction is kept to a minimum. Other issues facing refiners are the changes in oil demand patterns and government responses to the market. 2 tables.

Simulation model for wind energy storage systems. Volume III. Program descriptions. [SIMWEST CODE

Energy Technology Data Exchange (ETDEWEB)

Warren, A.W.; Edsinger, R.W.; Burroughs, J.D.

1977-08-01

The effort developed a comprehensive computer program for the modeling of wind energy/storage systems utilizing any combination of five types of storage (pumped hydro, battery, thermal, flywheel and pneumatic). An acronym for the program is SIMWEST (Simulation Model for Wind Energy Storage). The level of detail of SIMWEST is consistent with a role of evaluating the economic feasibility as well as the general performance of wind energy systems. The software package consists of two basic programs and a library of system, environmental, and load components. Volume III, the SIMWEST program description contains program descriptions, flow charts and program listings for the SIMWEST Model Generation Program, the Simulation program, the File Maintenance program and the Printer Plotter program. Volume III generally would not be required by SIMWEST user.

Desulfurization of waste gases of the incinerator after petroleum refining

International Nuclear Information System (INIS)

Samesova, D.; Ladomersky, J.

2001-01-01

Desulfurization of waste gases of the incinerator after petroleum refining was developed. Mixing of wastes with lime (10% of additive of total volume of waste) was proved before introduction into incinerator. Concentrations of CO, CO 2 , O 2 , NO 2 , SO 2 and temperature of combustion products were measured by automatic analyser

The variable potency of TiB{sub 2} nucleant particles in the grain refinement of aluminium by Al-Ti-B additions

Energy Technology Data Exchange (ETDEWEB)

Quested, T.E.; Greer, A.L. [Cambridge Univ. (United Kingdom). Dept. of Metallurgy and Materials Science; Cooper, P.S. [London and Scandinavian Metallurgical Co. Ltd., Rotherham (United Kingdom)

2002-07-01

The development of Al-Ti-B grain-refiners is outlined. The relationships between nucleant particle potency, number and volume efficiencies, and overall refiner performance are explored. The importance of the particle size distribution is illustrated using hypothetical log-normal distributions in a thermal model for grain refinement which uses a free-growth criterion for grain initiation. In this way the degree of optimization of a current commercial refiner is assessed. (orig.)

Petroleum Refining and its Economic and Technological Impact for the Production of Gasoline in Mexico to 2030

Directory of Open Access Journals (Sweden)

Granados-Hernández Elías

2013-10-01

Full Text Available Gas imports in Mexico have increased in the last few years. Nowadays Mexico has no capacity to meet the demands of this fuel in the next twenty years. In this paper we analyze several oil refining projections that enable the oil supply in Mexico until year 2030, taking into consideration four types of refineries, processing the produc- tion of pure oils in the country, using four mixtures of the higher reserve, consider- ing an import to meet the demand of fuel and once met consider exportation. Modeling was carried out analyzing the volume of refined oil and the required in- vestment, based on the kind of refinery and on the processing units that characterize it. As it was mentioned before, there are different refining projections to meet the demand of gas, but considering that the main oil production in Mexico is heavy. The simulated projection with this type of oil would require a higher volume in the exis- tent refineries in the country to meet that demand. Besides, considering the kind of refinery (out of four, the volumes to refine will be less, if very complex refineries are used. However, the cost of investment in this technology would be higher, consider- ing that new refineries will be built in a near future to meet the fuel demands.

PROGRAM HTVOL: The Determination of Tree Crown Volume by Layers

Science.gov (United States)

Joseph C. Mawson; Jack Ward Thomas; Richard M. DeGraaf

1976-01-01

A FORTRAN IV computer program calculates, from a few field measurements, the volume of tree crowns. This volume is in layers of a specified thickness of trees or large shrubs. Each tree is assigned one of 15 solid forms, formed by using one of five side shapes (a circle, an ellipse, a neiloid, a triangle, or a parabolalike shape), and one of three bottom shapes (a...

Adaptive mesh refinement for a finite volume method for flow and transport of radionuclides in heterogeneous porous media

International Nuclear Information System (INIS)

Amaziane, Brahim; Bourgeois, Marc; El Fatini, Mohamed

2014-01-01

In this paper, we consider adaptive numerical simulation of miscible displacement problems in porous media, which are modeled by single phase flow equations. A vertex-centred finite volume method is employed to discretize the coupled system: the Darcy flow equation and the diffusion-convection concentration equation. The convection term is approximated with a Godunov scheme over the dual finite volume mesh, whereas the diffusion-dispersion term is discretized by piecewise linear conforming finite elements. We introduce two kinds of indicators, both of them of residual type. The first one is related to time discretization and is local with respect to the time discretization: thus, at each time, it provides an appropriate information for the choice of the next time step. The second is related to space discretization and is local with respect to both the time and space variable and the idea is that at each time it is an efficient tool for mesh adaptivity. An error estimation procedure evaluates where additional refinement is needed and grid generation procedures dynamically create or remove fine-grid patches as resolution requirements change. The method was implemented in the software MELODIE, developed by the French Institute for Radiological Protection and Nuclear Safety (IRSN, Institut de Radioprotection et de Surete Nucleaire). The algorithm is then used to simulate the evolution of radionuclide migration from the waste packages through a heterogeneous disposal, demonstrating its capability to capture complex behavior of the resulting flow. (authors)

Adaptive Finite Volume Method for the Shallow Water Equations on Triangular Grids

Directory of Open Access Journals (Sweden)

Sudi Mungkasi

2016-01-01

Full Text Available This paper presents a numerical entropy production (NEP scheme for two-dimensional shallow water equations on unstructured triangular grids. We implement NEP as the error indicator for adaptive mesh refinement or coarsening in solving the shallow water equations using a finite volume method. Numerical simulations show that NEP is successful to be a refinement/coarsening indicator in the adaptive mesh finite volume method, as the method refines the mesh or grids around nonsmooth regions and coarsens them around smooth regions.

Refining the Eye: Dermatology and Visual Literacy

Science.gov (United States)

Zimmermann, Corinne; Huang, Jennifer T.; Buzney, Elizabeth A.

2016-01-01

In 2014 the Museum of Fine Arts Boston and Harvard Medical School began a partnership focused on building visual literacy skills for dermatology residents in the Harvard Combined Dermatology Residency Program. "Refining the Eye: Art and Dermatology", a four session workshop, took place in the museum's galleries and utilized the Visual…

Constellation Program Lessons Learned. Volume 2; Detailed Lessons Learned

Science.gov (United States)

Rhatigan, Jennifer; Neubek, Deborah J.; Thomas, L. Dale

2011-01-01

These lessons learned are part of a suite of hardware, software, test results, designs, knowledge base, and documentation that comprises the legacy of the Constellation Program. The context, summary information, and lessons learned are presented in a factual format, as known and described at the time. While our opinions might be discernable in the context, we have avoided all but factually sustainable statements. Statements should not be viewed as being either positive or negative; their value lies in what we did and what we learned that is worthy of passing on. The lessons include both "dos" and "don ts." In many cases, one person s "do" can be viewed as another person s "don t"; therefore, we have attempted to capture both perspectives when applicable and useful. While Volume I summarizes the views of those who managed the program, this Volume II encompasses the views at the working level, describing how the program challenges manifested in day-to-day activities. Here we see themes that were perhaps hinted at, but not completely addressed, in Volume I: unintended consequences of policies that worked well at higher levels but lacked proper implementation at the working level; long-term effects of the "generation gap" in human space flight development, the need to demonstrate early successes at the expense of thorough planning, and the consequences of problems and challenges not yet addressed because other problems and challenges were more immediate or manifest. Not all lessons learned have the benefit of being operationally vetted, since the program was cancelled shortly after Preliminary Design Review. We avoid making statements about operational consequences (with the exception of testing and test flights that did occur), but we do attempt to provide insight into how operational thinking influenced design and testing. The lessons have been formatted with a description, along with supporting information, a succinct statement of the lesson learned, and

The Influence of Grain Refiners on the Efficiency of Ceramic Foam Filters

Science.gov (United States)

Towsey, Nicholas; Schneider, Wolfgang; Krug, Hans-Peter; Hardman, Angela; Keegan, Neil J.

An extensive program of work has been carried out to evaluate the efficiency of ceramic foam filters under carefully controlled conditions. Work reported at previous TMS meetings showed that in the absence of grain refiners, ceramic foam filters have the capacity for high filtration efficiency and consistent, reliable performance. The current phase of the investigation focuses on the impact grain refiner additions have on filter performance. The high filtration efficiencies obtained using 50 or 80ppi CFF's in the absence of grain refiners diminish when Al-3%Ti-1%B grain refiners are added. This, together with the impact of incoming inclusion loading on filter performance and the level of grain refiner addition are considered in detail. The new generation Al-3%Ti-0.15%C grain refiner has also been included. At typical addition levels (1kg/tonne) the effect on filter efficiency is similar to that for TiB2based grain refiners. The work was again conducted on a production scale using AA1050 alloy. Metal quality was determined using LiMCA and PoDFA. Spent filters were also analysed.

Adaptive mesh refinement in titanium

Energy Technology Data Exchange (ETDEWEB)

Colella, Phillip; Wen, Tong

2005-01-21

In this paper, we evaluate Titanium's usability as a high-level parallel programming language through a case study, where we implement a subset of Chombo's functionality in Titanium. Chombo is a software package applying the Adaptive Mesh Refinement methodology to numerical Partial Differential Equations at the production level. In Chombo, the library approach is used to parallel programming (C++ and Fortran, with MPI), whereas Titanium is a Java dialect designed for high-performance scientific computing. The performance of our implementation is studied and compared with that of Chombo in solving Poisson's equation based on two grid configurations from a real application. Also provided are the counts of lines of code from both sides.

Frequency Domain Computer Programs for Prediction and Analysis of Rail Vehicle Dynamics : Volume 1. Technical Report

Science.gov (United States)

1975-12-01

Frequency domain computer programs developed or acquired by TSC for the analysis of rail vehicle dynamics are described in two volumes. Volume I defines the general analytical capabilities required for computer programs applicable to single rail vehi...

An adaptive grid refinement strategy for the simulation of negative streamers

International Nuclear Information System (INIS)

Montijn, C.; Hundsdorfer, W.; Ebert, U.

2006-01-01

The evolution of negative streamers during electric breakdown of a non-attaching gas can be described by a two-fluid model for electrons and positive ions. It consists of continuity equations for the charged particles including drift, diffusion and reaction in the local electric field, coupled to the Poisson equation for the electric potential. The model generates field enhancement and steep propagating ionization fronts at the tip of growing ionized filaments. An adaptive grid refinement method for the simulation of these structures is presented. It uses finite volume spatial discretizations and explicit time stepping, which allows the decoupling of the grids for the continuity equations from those for the Poisson equation. Standard refinement methods in which the refinement criterion is based on local error monitors fail due to the pulled character of the streamer front that propagates into a linearly unstable state. We present a refinement method which deals with all these features. Tests on one-dimensional streamer fronts as well as on three-dimensional streamers with cylindrical symmetry (hence effectively 2D for numerical purposes) are carried out successfully. Results on fine grids are presented, they show that such an adaptive grid method is needed to capture the streamer characteristics well. This refinement strategy enables us to adequately compute negative streamers in pure gases in the parameter regime where a physical instability appears: branching streamers

40 CFR 80.593 - What are the reporting requirements for refiners and importers of motor vehicle diesel fuel...

Science.gov (United States)

2010-07-01

... for refiners and importers of motor vehicle diesel fuel subject to temporary refiner relief standards... PROGRAMS (CONTINUED) REGULATION OF FUELS AND FUEL ADDITIVES Motor Vehicle Diesel Fuel; Nonroad, Locomotive... the reporting requirements for refiners and importers of motor vehicle diesel fuel subject to...

Cleaning Data with OpenRefine

OpenAIRE

Seth van Hooland; Ruben Verborgh; Max De Wilde

2013-01-01

Duplicate records, empty values and inconsistent formats are phenomena we should be prepared to deal with when using historical data sets. This lesson will teach you how to discover inconsistencies in data contained within a spreadsheet or a database. As we increasingly share, aggregate and reuse data on the web, historians will need to respond to data quality issues which inevitably pop up. Using a program called OpenRefine, you will be able to easily identify systematic errors such as blank...

Metal decontamination for waste minimization using liquid metal refining technology

International Nuclear Information System (INIS)

Joyce, E.L. Jr.; Lally, B.; Ozturk, B.; Fruehan, R.J.

1993-01-01

The current Department of Energy Mixed Waste Treatment Project flowsheet indicates that no conventional technology, other than surface decontamination, exists for metal processing. Current Department of Energy guidelines require retrievable storage of all metallic wastes containing transuranic elements above a certain concentration. This project is in support of the National Mixed Low Level Waste Treatment Program. Because of the high cost of disposal, it is important to develop an effective decontamination and volume reduction method for low-level contaminated metals. It is important to be able to decontaminate complex shapes where surfaces are hidden or inaccessible to surface decontamination processes and destruction of organic contamination. These goals can be achieved by adapting commercial metal refining processes to handle radioactive and organic contaminated metal. The radioactive components are concentrated in the slag, which is subsequently vitrified; hazardous organics are destroyed by the intense heat of the bath. The metal, after having been melted and purified, could be recycled for use within the DOE complex. In this project, we evaluated current state-of-the-art technologies for metal refining, with special reference to the removal of radioactive contaminants and the destruction of hazardous organics. This evaluation was based on literature reports, industrial experience, plant visits, thermodynamic calculations, and engineering aspects of the various processes. The key issues addressed included radioactive partitioning between the metal and slag phases, minimization of secondary wastes, operability of the process subject to widely varying feed chemistry, and the ability to seal the candidate process to prevent the release of hazardous species

Proceedings of the 1995 U.S. DOE hydrogen program review, Volume 1

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-09-01

This document containes reports from the proceedings of the 1995 U.S. DOE hydrogen program review. Reports are organized under the topics of systems analysis, utilization, storage, and production. This volume, Volume I, contains the reports concerned with systems analysis and utilization. Individual reports were processed separately for the DOE data bases.

Segmental Refinement: A Multigrid Technique for Data Locality

Energy Technology Data Exchange (ETDEWEB)

Adams, Mark [Columbia Univ., New York, NY (United States). Applied Physics and Applied Mathematics Dept.; Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States)

2014-10-27

We investigate a technique - segmental refinement (SR) - proposed by Brandt in the 1970s as a low memory multigrid method. The technique is attractive for modern computer architectures because it provides high data locality, minimizes network communication, is amenable to loop fusion, and is naturally highly parallel and asynchronous. The network communication minimization property was recognized by Brandt and Diskin in 1994; we continue this work by developing a segmental refinement method for a finite volume discretization of the 3D Laplacian on massively parallel computers. An understanding of the asymptotic complexities, required to maintain textbook multigrid efficiency, are explored experimentally with a simple SR method. A two-level memory model is developed to compare the asymptotic communication complexity of a proposed SR method with traditional parallel multigrid. Performance and scalability are evaluated with a Cray XC30 with up to 64K cores. We achieve modest improvement in scalability from traditional parallel multigrid with a simple SR implementation.

Simultaneous refinement of two components of an exsolution intergrowth

DEFF Research Database (Denmark)

Topa, Dan; Petricek, Vaclav; Dusek, Michal

2008-01-01

Crystal structures of intergrown lindstromite and krupkaite were determined in two distinct samples by a simultaneous crystal-structure refinement using a modified JANA program package. The exsolution intergrowths have a bulk composition, determined by means of electron microprobe, equal to bd(60...

Programmable calculator programs to solve softwood volume and value equations.

Science.gov (United States)

Janet K. Ayer. Sachet

1982-01-01

This paper presents product value and product volume equations as programs for handheld calculators. These tree equations are for inland Douglas-fir, young-growth Douglas-fir, western white pine, ponderosa pine, and western larch. Operating instructions and an example are included.

Automated knowledge-base refinement

Science.gov (United States)

Mooney, Raymond J.

1994-01-01

Over the last several years, we have developed several systems for automatically refining incomplete and incorrect knowledge bases. These systems are given an imperfect rule base and a set of training examples and minimally modify the knowledge base to make it consistent with the examples. One of our most recent systems, FORTE, revises first-order Horn-clause knowledge bases. This system can be viewed as automatically debugging Prolog programs based on examples of correct and incorrect I/O pairs. In fact, we have already used the system to debug simple Prolog programs written by students in a programming language course. FORTE has also been used to automatically induce and revise qualitative models of several continuous dynamic devices from qualitative behavior traces. For example, it has been used to induce and revise a qualitative model of a portion of the Reaction Control System (RCS) of the NASA Space Shuttle. By fitting a correct model of this portion of the RCS to simulated qualitative data from a faulty system, FORTE was also able to correctly diagnose simple faults in this system.

Financial optimisation and risk management in refining activities

International Nuclear Information System (INIS)

Fiorenzani, S.

2006-01-01

The real options approach has become a benchmark in real assets evaluation and optimal management problems, especially in liberalised and competitive markets such as the oil and hydrocarbon markets. This paper describes how the same approach can be a useful tool for both risk management decisions and the financial optimisation problem. Refineries are black boxes, which can be used for the transformation of crude oil into more refined hydrocarbon products. These black boxes are characterised by operational flexibilities and constraints, which should be optimally managed in order to maximise the refiner's economic goals. Stochastic dynamic programming represents the right mathematical instrument employed to solve the decision-making problem in such an economic environment. (author)

The US petroleum refining industry in the 1980's

Energy Technology Data Exchange (ETDEWEB)

1990-10-11

As part of the EIA program on petroleum, The US Petroleum Refining Industry in the 1980's, presents a historical analysis of the changes that took place in the US petroleum refining industry during the 1980's. It is intended to be of interest to analysts in the petroleum industry, state and federal government officials, Congress, and the general public. The report consists of six chapters and four appendices. Included is a detailed description of the major events and factors that affected the domestic refining industry during this period. Some of the changes that took place in the 1980's are the result of events that started in the 1970's. The impact of these events on US refinery configuration, operations, economics, and company ownership are examined. 23 figs., 11 tabs.

Petroleum refining industry in China

International Nuclear Information System (INIS)

Walls, W.D.

2010-01-01

The oil refining industry in China has faced rapid growth in oil imports of increasingly sour grades of crude with which to satisfy growing domestic demand for a slate of lighter and cleaner finished products sold at subsidized prices. At the same time, the world petroleum refining industry has been moving from one that serves primarily local and regional markets to one that serves global markets for finished products, as world refining capacity utilization has increased. Globally, refined product markets are likely to experience continued globalization until refining investments significantly expand capacity in key demand regions. We survey the oil refining industry in China in the context of the world market for heterogeneous crude oils and growing world trade in refined petroleum products. (author)

40 CFR 80.554 - What compliance options are available to NRLM diesel fuel small refiners?

Science.gov (United States)

2010-07-01

... an approved motor vehicle diesel fuel small refiner under § 80.550(a) but does not qualify as a NRLM... to NRLM diesel fuel small refiners? 80.554 Section 80.554 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) REGULATION OF FUELS AND FUEL ADDITIVES Motor Vehicle...

40 CFR 80.910 - How does a refiner or importer apply for a toxics baseline?

Science.gov (United States)

2010-07-01

... for a toxics baseline? 80.910 Section 80.910 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) REGULATION OF FUELS AND FUEL ADDITIVES Gasoline Toxics Baseline Determination § 80.910 How does a refiner or importer apply for a toxics baseline? (a)(1) A refiner or importer...

Decontamination of steel by melt refining: A literature review

International Nuclear Information System (INIS)

Ozturk, B.; Fruehan, R.J.

1994-01-01

It has been reported that a large amount of metal waste is produced annually by nuclear fuel processing and nuclear power plants. These metal wastes are contaminated with radioactive elements, such as uranium and plutonium. Current Department of Energy guidelines require retrievable storage of all metallic wastes containing transuranic elements above a certain level. Because of high cost, it is important to develop an effective decontamination and volume reduction method for low level contaminated metals. It has been shown by some investigators that a melt refining technique can be used for the processing of the contaminated metal wastes. In this process, contaminated metal is melted wit a suitable flux. The radioactive elements are oxidized and transferred to a slag phase. In order to develop a commercial process it is important to have information on the thermodynamics and kinetics of the removal. Therefore, a literature search was carried out to evaluate the available information on the decontamination uranium and transuranic-contaminated plain steel, copper and stainless steel by melt a refining technique. Emphasis was given to the thermodynamics and kinetics of the removal. Data published in the literature indicate that it is possible to reduce the concentration of radioactive elements to a very low level by the melt refining method. 20 refs

North American refining

International Nuclear Information System (INIS)

Osten, James; Haltmaier, Susan

2000-01-01

This article examines the current status of the North American refining industry, and considers the North American economy and the growth in demand in the petroleum industry, petroleum product demand and quality, crude oil upgrading to meet product standards, and changes in crude oil feedstocks such as the use of heavier crudes and bitumens. Refining expansion, the declining profits in refining, and changes due to environmental standards are discussed. The Gross Domestic Product and oil demand for the USA, Canada, Mexico, and Venezuela for the years 1995-2020 are tabulated

Energy extension service pilot program evaluation report: the first year. Volume II: pilot state reports

Energy Technology Data Exchange (ETDEWEB)

1979-09-01

Volume II of the Energy Extension Service Evaluation presents a discussion of the operations of the ten EES pilot-state programs during the period from October 1, 1977 through September 30, 1978. Each of the ten pilot states - Alabama, Connecticut, Michigan, New Mexico, Pennsylvania, Tennessee, Texas, Washington, Wisconsin, and Wyoming - received a grant of approximately $1.1 million to develop and implement a 19-month program beginning on October 1, 1977. Volume II provides a case-study description of the operations of the pilot program in each state, with special attention given to the two programs selected in each state for more detailed study and survey research. Some survey data and analysis are presented for the emphasis programs.

Hydride heat pump. Volume I. Users manual for HYCSOS system design program. [HYCSOS code

Energy Technology Data Exchange (ETDEWEB)

Gorman, R.; Moritz, P.

1978-05-01

A method for the design and costing of a metal hydride heat pump for residential use and a computer program, HYCSOS, which automates that method are described. The system analyzed is one in which a metal hydride heat pump can provide space heating and space cooling powered by energy from solar collectors and electric power generated from solar energy. The principles and basic design of the system are presented, and the computer program is described giving detailed design and performance equations used in the program. The operation of the program is explained, and a sample run is presented. This computer program is part of an effort to design, cost, and evaluate a hydride heat pump for residential use. The computer program is written in standard Fortran IV and was run on a CDC Cyber 74 and Cyber 174 computer. A listing of the program is included as an appendix. This report is Volume 1 of a two-volume document.

Decadal climate prediction with a refined anomaly initialisation approach

Science.gov (United States)

Volpi, Danila; Guemas, Virginie; Doblas-Reyes, Francisco J.; Hawkins, Ed; Nichols, Nancy K.

2017-03-01

In decadal prediction, the objective is to exploit both the sources of predictability from the external radiative forcings and from the internal variability to provide the best possible climate information for the next decade. Predicting the climate system internal variability relies on initialising the climate model from observational estimates. We present a refined method of anomaly initialisation (AI) applied to the ocean and sea ice components of the global climate forecast model EC-Earth, with the following key innovations: (1) the use of a weight applied to the observed anomalies, in order to avoid the risk of introducing anomalies recorded in the observed climate, whose amplitude does not fit in the range of the internal variability generated by the model; (2) the AI of the ocean density, instead of calculating it from the anomaly initialised state of temperature and salinity. An experiment initialised with this refined AI method has been compared with a full field and standard AI experiment. Results show that the use of such refinements enhances the surface temperature skill over part of the North and South Atlantic, part of the South Pacific and the Mediterranean Sea for the first forecast year. However, part of such improvement is lost in the following forecast years. For the tropical Pacific surface temperature, the full field initialised experiment performs the best. The prediction of the Arctic sea-ice volume is improved by the refined AI method for the first three forecast years and the skill of the Atlantic multidecadal oscillation is significantly increased compared to a non-initialised forecast, along the whole forecast time.

NMR structural refinement of an extrahelical adenosine tridecamer d(CGCAGAATTCGCG)2 via a hybrid relaxation matrix procedure

International Nuclear Information System (INIS)

Nikonowicz, E.P.; Meadows, R.P.; Gorenstein, D.G.

1990-01-01

Until very recently interproton distances from NOESY experiments have been derived solely from the two-spin approximation method. Unfortunately, even at short mixing times, there is a significant error in many of these distances. A complete relaxation matrix approach employing a matrix eigenvalue/eigenvector solution to the Bloch equations avoids the approximation of the two-spin method. The authors calculated the structure of an extrahelical adenosine tridecamer oligodeoxyribonucleotide duplex, d-(CGCAGAATTCGCG) 2 , by an iterative refinement approach using a hybrid relaxation matrix method combined with restrained molecular dynamics calculations. Distances from the 2D NOESY spectra have been calculated from the relaxation rate matrix which has been evaluated from a hybrid NOESY volume matrix comprising elements from the experiment and those calculated from an initial structure. The hybrid matrix derived distances have then been used in a restrained molecular dynamics procedure to obtain a new structure that better approximates the NOESY spectra. The resulting partially refined structure is then used to calculate an improved theoretical NOESY volume matrix which is once again merged with the experimental matrix until refinement is complete. Although the crystal structure of the tridecamer clearly shows the extrahelical adenosine looped out way from the duplex, the NOESY distance restrained hybrid matrix/molecular dynamics structural refinement establishes that the extrahelical adenosine stacks into the duplex

Creating value in refining

International Nuclear Information System (INIS)

Cobb, C.B.

2001-01-01

This article focuses on recent developments in the US refining industry and presents a model for improving the performance of refineries based on the analysis of the refining industry by Cap Gemini Ernst and Young. The identification of refineries in risk of failing, the construction of pipelines for refinery products from Gulf State refineries, mergers and acquisitions, and poor financial performance are discussed. Current challenges concerning the stagnant demand for refinery products, environmental regulations, and shareholder value are highlighted. The structure of the industry, the creation of value in refining, and the search for business models are examined. The top 25 US companies and US refining business groups are listed

Small Business Management Volume III: Curriculum. An Adult Education Program.

Science.gov (United States)

Persons, Edgar A.; Swanson, Gordon I.

The small business management adult education program outlined in this curriculum guide is designed to help small business entrepreneurs solve their business management problems and attain the goals they have established for their businesses and their families. (An instructor's manual and practice problems are in separate volumes.) The 3-year…

Refined universal laws for hull volumes and perimeters in large planar maps

International Nuclear Information System (INIS)

Guitter, Emmanuel

2017-01-01

We consider ensembles of planar maps with two marked vertices at distance k from each other, and look at the closed line separating these vertices and lying at distance d from the first one ( d   <   k ). This line divides the map into two components, the hull at distance d which corresponds to the part of the map lying on the same side as the first vertex and its complementary. The number of faces within the hull is called the hull volume, and the length of the separating line the hull perimeter. We study the statistics of the hull volume and perimeter for arbitrary d and k in the limit of infinitely large planar quadrangulations, triangulations and Eulerian triangulations. We consider more precisely situations where both d and k become large with the ratio d / k remaining finite. For infinitely large maps, two regimes may be encountered: either the hull has a finite volume and its complementary is infinitely large, or the hull itself has an infinite volume and its complementary is of finite size. We compute the probability for the map to be in either regime as a function of d / k as well as a number of universal statistical laws for the hull perimeter and volume when maps are conditioned to be in one regime or the other. (paper)

Dynamic Programming Algorithm for Generation of Optimal Elimination Trees for Multi-frontal Direct Solver Over H-refined Grids

KAUST Repository

AbouEisha, Hassan M.

2014-06-06

In this paper we present a dynamic programming algorithm for finding optimal elimination trees for computational grids refined towards point or edge singularities. The elimination tree is utilized to guide the multi-frontal direct solver algorithm. Thus, the criterion for the optimization of the elimination tree is the computational cost associated with the multi-frontal solver algorithm executed over such tree. We illustrate the paper with several examples of optimal trees found for grids with point, isotropic edge and anisotropic edge mixed with point singularity. We show the comparison of the execution time of the multi-frontal solver algorithm with results of MUMPS solver with METIS library, implementing the nested dissection algorithm.

Predictive Software Cost Model Study. Volume I. Final Technical Report.

Science.gov (United States)

1980-06-01

development phase to identify computer resources necessary to support computer programs after transfer of program manangement responsibility and system... classical model development with refinements specifically applicable to avionics systems. The refinements are the result of the Phase I literature search

Southeast Asian oil markets and refining

Energy Technology Data Exchange (ETDEWEB)

Yamaguchi, N.D. [FACTS, Inc., Honolulu, Hawaii (United States)

1999-09-01

An overview of the Southeast Asian oil markets and refining is presented concentrating on Brunei, Malaysia, the Philippines, Singapore and Thailand refiners. Key statistics of the refiners in this region are tabulated. The demand and the quality of Indonesian, Malaysian, Philippine, Singapore and Thai petroleum products are analysed. Crude distillation unit capacity trends in the Southeastern Asian refining industry are discussed along with cracking to distillation ratios, refining in these countries, and the impact of changes in demand and refining on the product trade.

Southeast Asian oil markets and refining

International Nuclear Information System (INIS)

Yamaguchi, N.D.

1999-01-01

An overview of the Southeast Asian oil markets and refining is presented concentrating on Brunei, Malaysia, the Philippines, Singapore and Thailand refiners. Key statistics of the refiners in this region are tabulated. The demand and the quality of Indonesian, Malaysian, Philippine, Singapore and Thai petroleum products are analysed. Crude distillation unit capacity trends in the Southeastern Asian refining industry are discussed along with cracking to distillation ratios, refining in these countries, and the impact of changes in demand and refining on the product trade

The regulations concerning refining business of nuclear source material and nuclear fuel materials

International Nuclear Information System (INIS)

1979-01-01

The regulations are provided for under the law for the regulations of nuclear source materials, nuclear fuel materials and reactors and provisions concerning refining business in the enforcement order for the law. The basic concepts and terms are defined, such as: exposure dose, accumulative dose; controlled area; inspected surrounding area and employee. Refining facilities listed in the application for designation shall be classified into clushing and leaching, thickning, refining facilities, storage facilities of nuclear source materials and nuclear fuel materials, disposal facilities of contaminated substances and building for refining, etc. Business program attached to the application shall include expected time of beginning of refining, estimated production amount of nuclear source materials or nuclear fuel materials for the first three years and funds necessary for construction, etc. Records shall be made and kept for particular periods on delivery and storage of nuclear source materials and nuclear fuel materials, control of radiation, maintenance and accidents of refining facilities. Safety securing, application of internationally regulated substances and measures in dangerous situations are stipulated respectively. Exposure dose of employees and other specified matters shall be reported by the refiner yearly to the Director General of Science and Technology Agency and the Minister of International Trade and Industry. (Okada, K.)

Linkages between the markets for crude oil and the markets for refined products

International Nuclear Information System (INIS)

Didziulis, V.S.

1990-01-01

To understand the crude oil price determination process it is necessary to extend the analysis beyond the markets for petroleum. Crude oil prices are determined in two closely related markets: the markets for crude oil and the markets for refined products. An econometric-linear programming model was developed to capture the linkages between the markets for crude oil and refined products. In the LP refiners maximize profits given crude oil supplies, refining capacities, and prices of refined products. The objective function is profit maximization net of crude oil prices. The shadow price on crude oil gives the netback price. Refined product prices are obtained from the econometric models. The model covers the free world divided in five regions. The model is used to analyze the impacts on the markets of policies that affect crude oil supplies, the demands for refined products, and the refining industry. For each scenario analyzed the demand for crude oil is derived from the equilibrium conditions in the markets for products. The demand curve is confronted with a supply curve which maximizes revenues providing an equilibrium solution for both crude oil and product markets. The model also captures crude oil price differentials by quality. The results show that the demands for crude oil are different across regions due to the structure of the refining industries and the characteristics of the demands for refined products. Changes in the demands for products have a larger impact on the markets than changes in the refining industry. Since markets for refined products and crude oil are interrelated they can't be analyzed individually if an accurate and complete assessment of a policy is to be made. Changes in only one product market in one region affect the other product markets and the prices of crude oil

A survey of electric and hybrid vehicles simulation programs. Volume 2: Questionnaire responses

Science.gov (United States)

Bevan, J.; Heimburger, D. A.; Metcalfe, M. A.

1978-01-01

The data received in a survey conducted within the United States to determine the extent of development and capabilities of automotive performance simulation programs suitable for electric and hybrid vehicle studies are presented. The survey was conducted for the Department of Energy by NASA's Jet Propulsion Laboratory. Volume 1 of this report summarizes and discusses the results contained in Volume 2.

Effect of strontium on the grain refining efficiency of Mg-3Al alloy refined by carbon inoculation

International Nuclear Information System (INIS)

Du Jun; Yang Jian; Kuwabara, Mamoru; Li Wenfang; Peng Jihua

2009-01-01

The effect of Sr on the grain refining efficiency of the Mg-3Al alloy refined by carbon inoculation has been investigated in the present study. A significant grain refinement was obtained for the Mg-3Al alloy treated with either 0.2% C or 0.2% Sr. The Al-C-O particles were found in the sample refined by 0.2% C, and the element O should come from reaction between Al 4 C 3 nuclei of Mg grains and water during the process of sample preparation. The grain size of the sample refined by carbon inoculation was further decreased after the combined addition of Sr. The grain size decreased with increasing Sr content. Much higher refining efficiency was obtained when the Sr addition was increased to 0.5%. Sr is an effective element to improve the grain refining efficiency for the Mg-Al alloys refined by carbon inoculation. The number of Al 4 C 3 particles in the sample refined by the combination of carbon and Sr was more than that in the sample refined by only carbon. No Al-C-O-Sr-rich particles were obviously found in the sample refined by the combination of carbon and a little (<0.5%) Sr addition

40 CFR 80.1347 - What are the sampling and testing requirements for refiners and importers?

Science.gov (United States)

2010-07-01

... reformulated or conventional gasoline or RBOB to produce conventional gasoline at a refinery, must exclude the... refinery and the volume and benzene content of gasoline produced at the refinery, and use the compliance... previously certified gasoline that is used to produce conventional gasoline the refiner must include the...

SCJ-Circus: a refinement-oriented formal notation for Safety-Critical Java

Directory of Open Access Journals (Sweden)

Alvaro Miyazawa

2016-06-01

Full Text Available Safety-Critical Java (SCJ is a version of Java whose goal is to support the development of real-time, embedded, safety-critical software. In particular, SCJ supports certification of such software by introducing abstractions that enforce a simpler architecture, and simpler concurrency and memory models. In this paper, we present SCJ-Circus, a refinement-oriented formal notation that supports the specification and verification of low-level programming models that include the new abstractions introduced by SCJ. SCJ-Circus is part of the family of state-rich process algebra Circus, as such, SCJ-Circus includes the Circus constructs for modelling sequential and concurrent behaviour, real-time and object orientation. We present here the syntax and semantics of SCJ-Circus, which is defined by mapping SCJ-Circus constructs to those of standard Circus. This is based on an existing approach for modelling SCJ programs. We also extend an existing Circus-based refinement strategy that targets SCJ programs to account for the generation of SCJ-Circus models close to implementations in SCJ.

Research program plan: piping. Volume 3

International Nuclear Information System (INIS)

Vagins, M.; Strosnider, J.

1985-07-01

Regulatory issues related to piping can be divided into the three areas of pipe cracking, postulated design basis pipe breaks, and design of piping for seismic and other dynamic loads. The first two of these issues are in the domain of the Materials Engineering Branch (MEBR), while the last of the three issues is the responsibility of the Mechanical/Structural Engineering Branch. This volume of the MEBR Research Plan defines the critical aspects of the pipe cracking and postulated design basis pipe break issues and identifies those research efforts and results necessary for their resolution. In general, the objectives of the MERB Piping Research Program are to provide experimentally validated analytic techniques and appropriate material properties characterization methods and data to support regulatory activities related to evaluating and ensuring piping integrity

Frequency-restrained structure-factor refinement. Pt. 1

International Nuclear Information System (INIS)

Lunin, V.Yu.; Skovoroda, T.P.

1991-01-01

An analysis of the frequencies of different values encountered in protein electron-density syntheses reveals characteristic shapes for their distributions (histograms). This property can be used to refine ill-defined phases (and, perhaps, some of the moduli) of structure factors, and thus to obtain more-interpretable electron-density maps. A simple empirical model is designed which can predict the histogram for a protein with an undetermined structure provided its unit-cell volume and charge are known. The parameters of the histogram model are derived from a set of proteins with known spatial structures. The application of the simulated histogram is illustrated by an improved electron-density map for the 'dry' form of the protein γ-crystallin IIIb. (orig.)

A conformation-dependent stereochemical library improves crystallographic refinement even at atomic resolution

International Nuclear Information System (INIS)

Tronrud, Dale E.; Karplus, P. Andrew

2011-01-01

A script was created to allow SHELXL to use the new CDL v.1.2 stereochemical library which defines the target values for main-chain bond lengths and angles as a function of the residue’s ϕ/ψ angles. Test refinements using this script show that the refinement behavior of structures at resolutions even better than 1 Å is substantially enhanced by the use of the new conformation-dependent ideal geometry paradigm. To utilize a new conformation-dependent backbone-geometry library (CDL) in protein refinements at atomic resolution, a script was written that creates a restraint file for the SHELXL refinement program. It was found that the use of this library allows models to be created that have a substantially better fit to main-chain bond angles and lengths without degrading their fit to the X-ray data even at resolutions near 1 Å. For models at much higher resolution (∼0.7 Å), the refined model for parts adopting single well occupied positions is largely independent of the restraints used, but these structures still showed much smaller r.m.s.d. residuals when assessed with the CDL. Examination of the refinement tests across a wide resolution range from 2.4 to 0.65 Å revealed consistent behavior supporting the use of the CDL as a next-generation restraint library to improve refinement. CDL restraints can be generated using the service at http://pgd.science.oregonstate.edu/cdl_shelxl/

Measuring coalition functioning: refining constructs through factor analysis.

Science.gov (United States)

Brown, Louis D; Feinberg, Mark E; Greenberg, Mark T

2012-08-01

Internal and external coalition functioning is an important predictor of coalition success that has been linked to perceived coalition effectiveness, coalition goal achievement, coalition ability to support evidence-based programs, and coalition sustainability. Understanding which aspects of coalition functioning best predict coalition success requires the development of valid measures of empirically unique coalition functioning constructs. The goal of the present study is to examine and refine the psychometric properties of coalition functioning constructs in the following six domains: leadership, interpersonal relationships, task focus, participation benefits/costs, sustainability planning, and community support. The authors used factor analysis to identify problematic items in our original measure and then piloted new items and scales to create a more robust, psychometrically sound, multidimensional measure of coalition functioning. Scales displayed good construct validity through correlations with other measures. Discussion considers the strengths and weaknesses of the refined instrument.

Commercial refining in the Mediterranean

International Nuclear Information System (INIS)

Packer, P.

1999-01-01

About 9% of the world's oil refining capacity is on the Mediterranean: some of the world's biggest and most advanced refineries are on Sicily and Sardinia. The Mediterranean refineries are important suppliers to southern Europe and N. Africa. The article discusses commercial refining in the Mediterranean under the headings of (i) historic development, (ii) product demand, (iii) refinery configurations, (iv) refined product trade, (v) financial performance and (vi) future outlook. Although some difficulties are foreseen, refining in the Mediterranean is likely to continue to be important well into the 21st century. (UK)

Effects of slag composition and process variables on decontamination of metallic wastes by melt refining

International Nuclear Information System (INIS)

Heshmatpour, B.; Copeland, G.L.

1981-01-01

Melt refining has been suggested as an alternative for decontamination and volume reduction of low-level-contaminated metallic wastes. Knowledge of metallurgical and thermochemical aspects of the process is essential for effective treatment of various metals. Variables such as slag type and composition, melting technique, and refractory materials need to be identified for each metal or alloy. Samples of contaminated metals were melted with fluxes by resistance furnace or induction heating. The resulting ingots as well as the slags were analyzed for their nuclide contents, and the corresponding partition ratios were calculated. Compatibility of slags and refractories was also investigated, and proper refractory materials were identified. Resistance furnace melting appeared to be a better melting technique for nonferrous scrap, while induction melting was more suitable for ferrous metals. In general uranium contents of the metals, except for aluminum, could be reduced to as low as 0.01 to 0.1 ppM by melt refining. Aluminum could be decontaminated to about 1 to 2 ppM U when certain fluoride slags were used. The extent of decontamination was not very sensitive to slag type and composition. However, borosilicate and basic oxidizing slags were more effective on ferrous metals and Cu; NaNO 3 -NaCl-NaOH type fluxes were desirable for Zn, Pb, and Sn; and fluoride type slags were effective for decontamination of Al. Recrystallized alumina proved to be the most compatible refractory for melt refining both ferrous and nonferrous metals, while graphite was suitable for nonferrous metal processing. In conclusion, melt refining is an effective technique for volume reduction ad decontamination of contaminated metal scrap when proper slags, melting technique, and refractories are used

Refining Nodes and Edges of State Machines

DEFF Research Database (Denmark)

Hallerstede, Stefan; Snook, Colin

2011-01-01

State machines are hierarchical automata that are widely used to structure complex behavioural specifications. We develop two notions of refinement of state machines, node refinement and edge refinement. We compare the two notions by means of examples and argue that, by adopting simple conventions...... refinement theory and UML-B state machine refinement influences the style of node refinement. Hence we propose a method with direct proof of state machine refinement avoiding the detour via Event-B that is needed by UML-B....

Research-Based Program Development: Refining the Service Model for a Geographic Alliance

Science.gov (United States)

Rutherford, David J.; Lovorn, Carley

2018-01-01

Research conducted in 2013 identified the perceptions that K-12 teachers and administrators hold with respect to: (1) the perceived needs in education, (2) the professional audiences that are most important to reach, and (3) the service models that are most effective. The specific purpose of the research was to refine and improve the services that…

40 CFR 80.290 - How does a refiner apply for a sulfur baseline?

Science.gov (United States)

2010-07-01

... baseline? 80.290 Section 80.290 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... (abt) Program-General Information § 80.290 How does a refiner apply for a sulfur baseline? (a) The... accordance with § 80.217. (b) The sulfur baseline request must be sent to: U.S. EPA, Attn: Sulfur Program...

Grain refinement of zinc-aluminium alloys

International Nuclear Information System (INIS)

Zaid, A.I.O.

2006-01-01

It is now well-established that the structure of the zinc-aluminum die casting alloys can be modified by the binary Al-Ti or the ternary Al-Ti-B master alloys. in this paper, grain refinement of zinc-aluminum alloys by rare earth materials is reviewed and discussed. The importance of grain refining of these alloys and parameters affecting it are presented and discussed. These include parameters related to the Zn-Al alloys cast, parameters related to the grain refining elements or alloys and parameters related to the process. The effect of addition of other alloying elements e.g. Zr either alone or in the presence of the main grain refiners Ti or Ti + B on the grain refining efficiency is also reviewed and discussed. Furthermore, based on the grain refinement and the parameters affecting it, a criterion for selection of the optimum grain refiner is suggested. Finally, the recent research work on the effect of grain refiners on the mechanical behaviour, impact strength, wear resistance, and fatigue life of these alloys are presented and discussed. (author)

Rietica - a visual Rietveld program

International Nuclear Information System (INIS)

Hunter, B.A.

2000-01-01

Full text: Rietica is a Rietveld analysis program that allows interaction with the refinement process on a cycle by cycle basis using a graphic interface. Rietica was developed to aid in the creation and updating of the Rietveld input files, as well as to control the LHPM program. It is a Windows 95 based program allowing point and click control of all the functionality of LHPM. Some of the features of the Rietica program are: multiple x-ray and/or neutron histograms (datasets) allowing different scales, zeros, peak profile types and values, backgrounds, wavelengths, preferred orientations for each histogram - all of which are refinable, (1) ability to calculate and refine neutron time-of-flight (TOF) data, (2) ability to refine Δf' and Δf'' now allows extra flexibility with synchrotron diffraction data, (3) can interpolate x-ray form factors from a series of (sin(θ)/λ, f) values (eg Bessel functions), (4) a new absorption correction formula allowing μR > 1.0 for cylindrical geometry and a flat plate absorption correction based surface roughness, (5) new background functions, (6) quantitative phase analysis routines, (7) point and click data entry and program control, (8) data display and easy background and excluded region input via mouse control, (9) control of the refinement process, including automatic updating of the calculated pattern display after each step, (10) can refine using 3 strategies: a) a point and click mode of data entry and refinement control (beginners/intermediate/advanced users); b) a manual editing of the input file, but still with all the benefits of the visual interface and online graphics (intermediate/advanced users); and c) a Basic scripting language that can be used to control the refinement process and graphics output. It could be used, say, for automatic refinement of large numbers of datasets (advanced users). The program currently reads in LHPM and GSAS/Fullprof/DWBS experiment files and export in a variety of formats. The

Refining and petrochemicals

Energy Technology Data Exchange (ETDEWEB)

Constancio, Silva

2006-07-01

In 2004, refining margins showed a clear improvement that persisted throughout the first three quarters of 2005. This enabled oil companies to post significantly higher earnings for their refining activity in 2004 compared to 2003, with the results of the first half of 2005 confirming this trend. As for petrochemicals, despite a steady rise in the naphtha price, higher cash margins enabled a turnaround in 2004 as well as a clear improvement in oil company financial performance that should continue in 2005, judging by the net income figures reported for the first half-year. Despite this favorable business environment, capital expenditure in refining and petrochemicals remained at a low level, especially investment in new capacity, but a number of projects are being planned for the next five years. (author)

Refining and petrochemicals

International Nuclear Information System (INIS)

Constancio, Silva

2006-01-01

In 2004, refining margins showed a clear improvement that persisted throughout the first three quarters of 2005. This enabled oil companies to post significantly higher earnings for their refining activity in 2004 compared to 2003, with the results of the first half of 2005 confirming this trend. As for petrochemicals, despite a steady rise in the naphtha price, higher cash margins enabled a turnaround in 2004 as well as a clear improvement in oil company financial performance that should continue in 2005, judging by the net income figures reported for the first half-year. Despite this favorable business environment, capital expenditure in refining and petrochemicals remained at a low level, especially investment in new capacity, but a number of projects are being planned for the next five years. (author)

Isotope Brayton ground demonstration testing and flight qualification. Volume 1. Technical program

Energy Technology Data Exchange (ETDEWEB)

1974-12-09

A program is proposed for the ground demonstration, development, and flight qualification of a radioisotope nuclear heated dynamic power system for use on space missions beginning in the 1980's. This type of electrical power system is based upon and combines two aerospace technologies currently under intense development; namely, the MHW isotope heat source and the closed Brayton cycle gas turbine. This power system represents the next generation of reliable, efficient economic electrical power equipment for space, and will be capable of providing 0.5 to 2.0 kW of electric power to a wide variety of spacecraft for earth orbital and interplanetary missions. The immediate design will be based upon the requirements for the Air Force SURVSATCOM mission. The proposal is presented in three volumes plus an Executive Summary. This volume describes the tasks in the technical program.

Grain refinement of aluminum and its alloys

International Nuclear Information System (INIS)

Zaid, A.I.O.

2001-01-01

Grain refinement of aluminum and its alloys by the binary Al-Ti and Ternary Al-Ti-B master alloys is reviewed and discussed. The importance of grain refining to the cast industry and the parameters affecting it are presented and discussed. These include parameters related to the cast, parameters related to the grain refining alloy and parameters related to the process. The different mechanisms, suggested in the literature for the process of grain refining are presented and discussed, from which it is found that although the mechanism of refining by the binary Al-Ti is well established the mechanism of grain refining by the ternary Al-Ti-B is still a controversial matter and some research work is still needed in this area. The effect of the addition of other alloying elements in the presence of the grain refiner on the grain refining efficiency is also reviewed and discussed. It is found that some elements e.g. V, Mo, C improves the grain refining efficiency, whereas other elements e.g. Cr, Zr, Ta poisons the grain refinement. Based on the parameters affecting the grain refinement and its mechanism, a criterion for selection of the optimum grain refiner is forwarded and discussed. (author)

Savannah River Site Environmental Implementation Plan. Volume 2, Protection programs

Energy Technology Data Exchange (ETDEWEB)

1989-08-01

Formal sitewide environmental planning at the . Savannah River Site (SRS) began in 1986 with the development and adoption of the Strategic Environmental Plan. The Strategic Environmental Plan describes the philosophy, policy, and overall program direction of environmental programs for the operation of the SRS. The Strategic Environmental Plan (Volume 2) provided the basis for development of the Environmental Implementation Plan (EIP). The EIP is the detailed, comprehensive environmental master plan for operating contractor organizations at the SRS. The EIP provides a process to ensure that all environmental requirements and obligations are being met by setting specific measurable goals and objectives and strategies for implementation. The plan is the basis for justification of site manpower and funding requests for environmental projects and programs over a five-year planning period.

Subseabed Disposal Program Plan. Volume II. FY80 budget and subtask work plans

International Nuclear Information System (INIS)

1980-01-01

This volume of the Subseabed Disposal Program Plan presents a breakdown of the master program structure by major activity. Each activity is described and accompanied by a specific cost plan schedule and a milestone plan. The costs have been compiled in the Cost Plan Schedules attached to each Subtask Work Plan. The FY 1980 budget for the Subseabed Disposal Program is summarized at the second level of the Work Breakdown Structure. The milestone plans for FY 80 are presented. The milestones can be changed only with the concurrence of the Sandia Subseabed Program Manager

A parallel adaptive mesh refinement algorithm for predicting turbulent non-premixed combusting flows

International Nuclear Information System (INIS)

Gao, X.; Groth, C.P.T.

2005-01-01

A parallel adaptive mesh refinement (AMR) algorithm is proposed for predicting turbulent non-premixed combusting flows characteristic of gas turbine engine combustors. The Favre-averaged Navier-Stokes equations governing mixture and species transport for a reactive mixture of thermally perfect gases in two dimensions, the two transport equations of the κ-ψ turbulence model, and the time-averaged species transport equations, are all solved using a fully coupled finite-volume formulation. A flexible block-based hierarchical data structure is used to maintain the connectivity of the solution blocks in the multi-block mesh and facilitate automatic solution-directed mesh adaptation according to physics-based refinement criteria. This AMR approach allows for anisotropic mesh refinement and the block-based data structure readily permits efficient and scalable implementations of the algorithm on multi-processor architectures. Numerical results for turbulent non-premixed diffusion flames, including cold- and hot-flow predictions for a bluff body burner, are described and compared to available experimental data. The numerical results demonstrate the validity and potential of the parallel AMR approach for predicting complex non-premixed turbulent combusting flows. (author)

A simple nodal force distribution method in refined finite element meshes

Energy Technology Data Exchange (ETDEWEB)

Park, Jai Hak [Chungbuk National University, Chungju (Korea, Republic of); Shin, Kyu In [Gentec Co., Daejeon (Korea, Republic of); Lee, Dong Won [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of); Cho, Seungyon [National Fusion Research Institute, Daejeon (Korea, Republic of)

2017-05-15

In finite element analyses, mesh refinement is frequently performed to obtain accurate stress or strain values or to accurately define the geometry. After mesh refinement, equivalent nodal forces should be calculated at the nodes in the refined mesh. If field variables and material properties are available at the integration points in each element, then the accurate equivalent nodal forces can be calculated using an adequate numerical integration. However, in certain circumstances, equivalent nodal forces cannot be calculated because field variable data are not available. In this study, a very simple nodal force distribution method was proposed. Nodal forces of the original finite element mesh are distributed to the nodes of refined meshes to satisfy the equilibrium conditions. The effect of element size should also be considered in determining the magnitude of the distributing nodal forces. A program was developed based on the proposed method, and several example problems were solved to verify the accuracy and effectiveness of the proposed method. From the results, accurate stress field can be recognized to be obtained from refined meshes using the proposed nodal force distribution method. In example problems, the difference between the obtained maximum stress and target stress value was less than 6 % in models with 8-node hexahedral elements and less than 1 % in models with 20-node hexahedral elements or 10-node tetrahedral elements.

Experimental Engineering Section semiannual progress report, March 1-August 31, 1976. Volume 2. Biotechnology and environmental programs

Energy Technology Data Exchange (ETDEWEB)

Pitt, Jr., W. W.; Mrochek, J. E. [comps.

1978-03-01

This volume contains the progress report of the biotechnology and environmental programs in the Experimental Engineering Section of the Chemical Technology Division. Research efforts in these programs during this report period have been in five areas: (1) environmental research; (2) centrifugal analyzer development; (3) advanced analytical systems development; (4) bioengineering research; and (5) bioengineering development. Summaries of these programmatic areas are contained in Volume I.

Nucleation mechanisms of refined alpha microstructure in beta titanium alloys

Science.gov (United States)

Zheng, Yufeng

Due to a great combination of physical and mechanical properties, beta titanium alloys have become promising candidates in the field of chemical industry, aerospace and biomedical materials. The microstructure of beta titanium alloys is the governing factor that determines their properties and performances, especially the size scale, distribution and volume fraction of precipitate phase in parent phase matrix. Therefore in order to enhance the performance of beta titanium alloys, it is critical to obtain a thorough understanding of microstructural evolution in beta titanium alloys upon various thermal and/or mechanical processes. The present work is focusing on the study of nucleation mechanisms of refined alpha microstructure and super-refined alpha microstructure in beta titanium alloys in order to study the influence of instabilities within parent phase matrix on precipitates nucleation, including compositional instabilities and/or structural instabilities. The current study is primarily conducted in Ti-5Al-5Mo-5V-3Cr (wt%, Ti-5553), a commercial material for aerospace application. Refined and super-refined precipitates microstructure in Ti-5553 are obtained under specific accurate temperature controlled heat treatments. The characteristics of either microstructure are investigated in details using various characterization techniques, such as SEM, TEM, STEM, HRSTEM and 3D atom probe to describe the features of microstructure in the aspect of morphology, distribution, structure and composition. Nucleation mechanisms of refined and super-refined precipitates are proposed in order to fully explain the features of different precipitates microstructure in Ti-5553. The necessary thermodynamic conditions and detailed process of phase transformations are introduced. In order to verify the reliability of proposed nucleation mechanisms, thermodynamic calculation and phase field modeling simulation are accomplished using the database of simple binary Ti-Mo system

Niobium-base grain refiner for aluminium

International Nuclear Information System (INIS)

Silva Pontes, P. da; Robert, M.H.; Cupini, N.L.

1980-01-01

A new chemical grain refiner for aluminium has been developed, using inoculation of a niobium-base compound. When a bath of molten aluminium is inoculated whith this refiner, an intermetallic aluminium-niobium compound is formed which acts as a powerful nucleant, producing extremely fine structure comparable to those obtained by means of the traditional grain refiner based on titanium and boron. It was found that the refinement of the structure depends upon the weight percentage of the new refiner inoculated as well as the time of holding the bath after inoculation and before pouring, but mainly on the inoculating temperature. (Author) [pt

Alternative fuels for vehicles fleet demonstration program. Final report, volume 2: Appendices

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-06-01

The Alternative Fuels for Vehicles Fleet Demonstration Program (AFV-FDP) was a multiyear effort to collect technical data for use in determining the costs and benefits of alternative-fuel vehicles (AFVs) in typical applications in New York State. This report, Volume 2, includes 13 appendices to Volume 1 that expand upon issues raised therein. Volume 1 provides: (1) Information about the purpose and scope of the AFV-FDP; (2) A summary of AFV-FDP findings organized on the basis of vehicle type and fuel type; (3) A short review of the status of AFV technology development, including examples of companies in the State that are active in developing AFVs and AFV components; and (4) A brief overview of the status of AFV deployment in the State. Volume 3 provides expanded reporting of AFV-FDP technical details, including the complete texts of the brochure Garage Guidelines for Alternative Fuels and the technical report Fleet Experience Survey Report, plus an extensive glossary of AFV terminology. The appendices cover a wide range of issues including: emissions regulations in New York State; production and health effects of ozone; vehicle emissions and control systems; emissions from heavy-duty engines; reformulated gasoline; greenhouse gases; production and characteristics of alternative fuels; the Energy Policy Act of 1992; the Clean Fuel Fleet Program; garage design guidelines for alternative fuels; surveys of fleet managers using alternative fuels; taxes on conventional and alternative fuels; and zero-emission vehicle technology.

Indian refining industry

International Nuclear Information System (INIS)

Singh, I.J.

2002-01-01

The author discusses the history of the Indian refining industry and ongoing developments under the headings: the present state; refinery configuration; Indian capabilities for refinery projects; and reforms in the refining industry. Tables lists India's petroleum refineries giving location and capacity; new refinery projects together with location and capacity; and expansion projects of Indian petroleum refineries. The Indian refinery industry has undergone substantial expansion as well as technological changes over the past years. There has been progressive technology upgrading, energy efficiency, better environmental control and improved capacity utilisation. Major reform processes have been set in motion by the government of India: converting the refining industry from a centrally controlled public sector dominated industry to a delicensed regime in a competitive market economy with the introduction of a liberal exploration policy; dismantling the administered price mechanism; and a 25 year hydrocarbon vision. (UK)

Spanish Refining

International Nuclear Information System (INIS)

Lores, F.R.

2001-01-01

An overview of petroleum refining in Spain is presented (by Repsol YPF) and some views on future trends are discussed. Spain depends heavily on imports. Sub-headings in the article cover: sources of crude imports, investments and logistics and marketing, -detailed data for each are shown diagrammatically. Tables show: (1) economic indicators (e.g. total GDP, vehicle numbers and inflation) for 1998-200; (2) crude oil imports for 1995-2000; (3) oil products balance for 1995-2000; (4) commodities demand, by product; (5) refining in Spain in terms of capacity per region; (6) outlets in Spain and other European countries in 2002 and (7) sales distribution channel by product

Determination of phases of {alpha} - Fe{sub 2}O{sub 3}: SiO{sub 2} compound by the Rietveld refinement

Energy Technology Data Exchange (ETDEWEB)

Palomares S, S.A. [Istituto Materiali Speciali per Elettronica e Magnetismo (MASPEC), Parco Area delle Scienze 37A-43010 Loc. Fontanni, Parma (Italy); Ponce C, S.; Martinez, J.R. [Facultad de Ciencias, Universidad Autonoma de San Luis Potosi, 78000 San Luis Potosi (Mexico); Ruiz, F. [Instituto Potosino de Investigacion Cientifica y Tecnologica, Av. V. Carranza 2025, San Luis Potosi (Mexico)

2002-07-01

We use a variation of the Rietveld refinement method to calculate the amorphous content of composites formed by a silica xerogel amorphous matrix and iron particles embedded into. In order to apply the Rietveld refinement to amorphous structures an initial crystalline model is assumed with the same composition as the material to be modelled. In this work we try to refine the structure of compounds using the program MAUD. It is shown how this program can be used to determine the amorphous and crystalline fractions in composites consisting of an amorphous matrix and incorporated iron oxide particles. The analysed compounds underwent different thermal treatments. (Author)

Comparing Refinements for Failure and Bisimulation Semantics

NARCIS (Netherlands)

Eshuis, H.; Fokkinga, M.M.

2002-01-01

Refinement in bisimulation semantics is defined differently from refinement in failure semantics: in bisimulation semantics refinement is based on simulations between labelled transition systems, whereas in failure semantics refinement is based on inclusions between failure systems. There exist

Structure of 3 at.% and 9 at.% Si-doped HfO{sub 2} from combined refinement of X-ray and neutron diffraction patterns

Energy Technology Data Exchange (ETDEWEB)

Zhao, Lili [Department of Materials Science and Engineering, North Carolina State University, NC 27695 (United States); School of Information Science and Technology, Northwest University, Xi' an 710127 (China); Hou, Dong; Usher, Tedi-Marie; Iamsasri, Thanakorn; Fancher, Chris M.; Forrester, Jennifer S. [Department of Materials Science and Engineering, North Carolina State University, NC 27695 (United States); Nishida, Toshikazu [Department of Electrical and Computer Engineering, University of Florida, FL 32611 (United States); Moghaddam, Saeed [Department of Mechanical and Aerospace Engineering, University of Florida, FL 32611 (United States); Jones, Jacob L., E-mail: jacobjones@ncsu.edu [Department of Materials Science and Engineering, North Carolina State University, NC 27695 (United States)

2015-10-15

The crystal structure of 3 at.% and 9 at.% Si-doped HfO{sub 2} powder was determined through refinements using X-ray and neutron diffraction patterns. The lattice parameters, atomic positions, dopant occupancy, and the second phase fraction were determined with high precision using a combined full pattern fitting via the Rietveld method. The results show that both 3 at.% and 9 at.% Si-doped HfO{sub 2} powder exhibit the monoclinic crystal structure with P 1 2{sub 1}/c 1 space group. Through the combined refinement, the crystal structure parameters, especially for the positions and occupancies of the lighter atoms, were more precisely determined compared to independent X-ray diffraction refinement. Although the ionic radius of Si{sup 4+} is smaller than Hf{sup 4+}, with increasing Si occupancy, the unit cell volume slightly increases; possible mechanisms for this effect are discussed. Moreover, the refined results provide evidence of the existence of a non-equilibrium phase of Hf{sub x}Si{sub 1−x}O{sub 2}. The second phase (SiO{sub 2}) fraction is determined as 0.17 at.% for 3 at.% Si-doped HfO{sub 2} powders and 1.7 at.% for 9 at.% Si-doped HfO{sub 2} powders. - Highlights: • X-ray and neutron diffraction patterns were used to determine crystal structure. • Results from independent refinements and a combined refinement were compared. • Highly precise structural parameters were obtained by the combined refinement. • Structural data of 3 at.% and 9 at.% Si-doped HfO{sub 2} are provided. • The unit cell volume slightly increases with Si concentration from 3 to 9 at.%.

The durban beach monitoring program: simple surveys speak volumes

CSIR Research Space (South Africa)

de Wet, p

2010-10-01

Full Text Available program: simple surveys speak volumes Pierre de Wet, Andrew Mather, Andr? Theron SAEON summit, 6 October 2010 ? CSIR 2010 Slide 1www.csir.co.za Outline ? Background / History ? Monitoring area circle6 Examples of survey data & trends circle6...) and near-shore deposition cf. classical understanding / scheme ? CSIR 2010 Slide 6 ? id. areas vulnerable to erosion ? effect of replenishment rates / locations visible Beach survey data s h o r e l i n e p o s i t i o n [ m...

Latin American oil markets and refining

International Nuclear Information System (INIS)

Yamaguchi, N.D.; Obadia, C.

1999-01-01

This paper provides an overview of the oil markets and refining in Argentina, Brazil, Chile, Colombia, Ecuador, Mexico, Peru and Venezuela, and examines the production of crude oil in these countries. Details are given of Latin American refiners highlighting trends in crude distillation unit capacity, cracking to distillation ratios, and refining in the different countries. Latin American oil trade is discussed, and charts are presented illustrating crude production, oil consumption, crude refining capacity, cracking to distillation ratios, and oil imports and exports

Relational Demonic Fuzzy Refinement

Directory of Open Access Journals (Sweden)

Fairouz Tchier

2014-01-01

Full Text Available We use relational algebra to define a refinement fuzzy order called demonic fuzzy refinement and also the associated fuzzy operators which are fuzzy demonic join (⊔fuz, fuzzy demonic meet (⊓fuz, and fuzzy demonic composition (□fuz. Our definitions and properties are illustrated by some examples using mathematica software (fuzzy logic.

Panorama 2012 - Refining 2030

International Nuclear Information System (INIS)

Marion, Pierre; Saint-Antonin, Valerie

2011-11-01

The major uncertainty characterizing the global energy landscape impacts particularly on transport, which remains the virtually-exclusive bastion of the oil industry. The industry must therefore respond to increasing demand for mobility against a background marked by the emergence of alternatives to oil-based fuels and the need to reduce emissions of pollutants and greenhouse gases (GHG). It is in this context that the 'Refining 2030' study conducted by IFP Energies Nouvelles (IFPEN) forecasts what the global supply and demand balance for oil products could be, and highlights the type and geographical location of the refinery investment required. Our study shows that the bulk of the refining investment will be concentrated in the emerging countries (mainly those in Asia), whilst the areas historically strong in refining (Europe and North America) face reductions in capacity. In this context, the drastic reduction in the sulphur specification of bunker oil emerges as a structural issue for European refining, in the same way as increasingly restrictive regulation of refinery CO 2 emissions (quotas/taxation) and the persistent imbalance between gasoline and diesel fuels. (authors)

Solvent-refined-coal (SRC) process. Volume II. Sections V-XIV. Final report

Energy Technology Data Exchange (ETDEWEB)

1982-05-01

This report documents the completion of development work on the Solvent Refined Coal Process by The Pittsburgh and Midway Coal Mining Co. The work was initiated in 1966 under Office of Coal Research, US Department of Interior, Contract No. 14-01-0001-496 and completed under US Department of Energy Contract No. DE-AC05-79ET10104. This report discusses work leading to the development of the SRC-I and SRC-II processes, construction of the Fort Lewis Pilot Plant for the successful development of these processes, and results from the operation of this pilot plant. Process design data generated on a 1 ton-per-day Process Development Unit, bench-scale units and through numerous research projects in support of the design of major demonstration plants are also discussed in summary form and fully referenced in this report.

Refining margins and prospects

International Nuclear Information System (INIS)

Baudouin, C.; Favennec, J.P.

1997-01-01

Refining margins throughout the world have remained low in 1996. In Europe, in spite of an improvement, particularly during the last few weeks, they are still not high enough to finance new investments. Although the demand for petroleum products is increasing, experts are still sceptical about any rapid recovery due to prevailing overcapacity and to continuing capacity growth. After a historical review of margins and an analysis of margins by regions, we analyse refining over-capacities in Europe and the unbalances between production and demand. Then we discuss the current situation concerning barriers to the rationalization, agreements between oil companies, and the consequences on the future of refining capacities and margins. (author)

Block-structured Adaptive Mesh Refinement - Theory, Implementation and Application

Directory of Open Access Journals (Sweden)

Deiterding Ralf

2011-12-01

Full Text Available Structured adaptive mesh refinement (SAMR techniques can enable cutting-edge simulations of problems governed by conservation laws. Focusing on the strictly hyperbolic case, these notes explain all algorithmic and mathematical details of a technically relevant implementation tailored for distributed memory computers. An overview of the background of commonly used finite volume discretizations for gas dynamics is included and typical benchmarks to quantify accuracy and performance of the dynamically adaptive code are discussed. Large-scale simulations of shock-induced realistic combustion in non-Cartesian geometry and shock-driven fluid-structure interaction with fully coupled dynamic boundary motion demonstrate the applicability of the discussed techniques for complex scenarios.

User's operating procedures. Volume 3: Projects directorate information programs

Science.gov (United States)

Haris, C. G.; Harris, D. K.

1985-01-01

A review of the user's operating procedures for the scout project automatic data system, called SPADS is presented. SPADS is the results of the past seven years of software development on a prime mini-computer. SPADS was developed as a single entry, multiple cross-reference data management and information retrieval system for the automation of Project office tasks, including engineering, financial, managerial, and clerical support. This volume, three of three, provides the instructions to operate the projects directorate information programs in data retrieval and file maintenance via the user friendly menu drivers.

A directory of computer programs for assessment of radioactive waste disposal in geological formations. Volume 2

International Nuclear Information System (INIS)

Ashton, J.; Broyd, T.W.; Jones, M.A.; Knowles, N.C.; Liew, S.K.; Mawbey, C.S.; Read, D.; Smith, S.L.

1993-01-01

This directory describes computer programs suitable for the assessment of radioactive waste disposal facilities in geological formations. The programs, which are mainly applicable to the post-closure analysis of the repository, address combinations of the following topics: nuclide inventory, corrosion, leaching, geochemistry, geomechanics, heat transfer, groundwater flow, radionuclide migration, biosphere modelling, safety assessment and site evolution. A total of 320 programs are identified, of which 84 are reviewed in detail, 192 in summary and 44 in tabular fashion. Originally published in 1983, the directory was updated in 1985 with the addition of new programs and the revision of some of the existing program reviews. This directory has been completely rewritten in 1991 with the addition of more new programs and a full revision of all the existing program reviews, some of which have been deleted as they are no longer in general use. Although the directory is specific to the post-closure assessment of a repository site, some of the programs described can also be used in other areas of repository (e.g. repository design). This directory is composed of two volumes, the present volume is the second

A directory of computer programs for assessment of radioactive waste disposal in geological formations. Volume 1

International Nuclear Information System (INIS)

Ashton, J.; Broyd, T.W.; Jones, M.A.; Knowles, N.C.; Liew, S.K.; Mawbey, C.S.; Read, D.; Smith, S.L.

1993-01-01

This directory describes computer programs suitable for the assessment of radioactive waste disposal facilities in geological formations. The programs, which are mainly applicable to the post-closure analysis of the repository, address combinations of the following topics: nuclide inventory, corrosion, leaching, geochemistry, geomechanics, heat transfer, groundwater flow, radionuclide migration, biosphere modelling, safety assessment and site evolution. A total of 320 programs are identified of which 84 are reviewed in detail, 192 in summary and 44 in tabular fashion. Originally published in 1983, the directory was updated in 1985 with the addition of new programs and the revision of some of the existing program reviews. This directory has been completely rewritten in 1991 with the addition of more new programs and a full revision of all the existing program reviews, some of which have been deleted as they are no longer in general use. Although the directory is specific to the post-closure assessment of a repository site, some of the programs described can also be used in other areas of repository (e.g. repository design). This directory is composed of two volumes, the present volume is the first

Minerals Yearbook, volume II, Area Reports—Domestic

Science.gov (United States)

,

2018-01-01

The U.S. Geological Survey (USGS) Minerals Yearbook discusses the performance of the worldwide minerals and materials industries and provides background information to assist in interpreting that performance. Content of the individual Minerals Yearbook volumes follows:Volume I, Metals and Minerals, contains chapters about virtually all metallic and industrial mineral commodities important to the U.S. economy. Chapters on survey methods, summary statistics for domestic nonfuel minerals, and trends in mining and quarrying in the metals and industrial mineral industries in the United States are also included.Volume II, Area Reports: Domestic, contains a chapter on the mineral industry of each of the 50 States and Puerto Rico and the Administered Islands. This volume also has chapters on survey methods and summary statistics of domestic nonfuel minerals.Volume III, Area Reports: International, is published as four separate reports. These regional reports contain the latest available minerals data on more than 180 foreign countries and discuss the importance of minerals to the economies of these nations and the United States. Each report begins with an overview of the region’s mineral industries during the year. It continues with individual country chapters that examine the mining, refining, processing, and use of minerals in each country of the region and how each country’s mineral industry relates to U.S. industry. Most chapters include production tables and industry structure tables, information about Government policies and programs that affect the country’s mineral industry, and an outlook section.The USGS continually strives to improve the value of its publications to users. Constructive comments and suggestions by readers of the Minerals Yearbook are welcomed.

Minerals Yearbook, volume I, Metals and Minerals

Science.gov (United States)

,

2018-01-01

The U.S. Geological Survey (USGS) Minerals Yearbook discusses the performance of the worldwide minerals and materials industries and provides background information to assist in interpreting that performance. Content of the individual Minerals Yearbook volumes follows:Volume I, Metals and Minerals, contains chapters about virtually all metallic and industrial mineral commodities important to the U.S. economy. Chapters on survey methods, summary statistics for domestic nonfuel minerals, and trends in mining and quarrying in the metals and industrial mineral industries in the United States are also included.Volume II, Area Reports: Domestic, contains a chapter on the mineral industry of each of the 50 States and Puerto Rico and the Administered Islands. This volume also has chapters on survey methods and summary statistics of domestic nonfuel minerals.Volume III, Area Reports: International, is published as four separate reports. These regional reports contain the latest available minerals data on more than 180 foreign countries and discuss the importance of minerals to the economies of these nations and the United States. Each report begins with an overview of the region’s mineral industries during the year. It continues with individual country chapters that examine the mining, refining, processing, and use of minerals in each country of the region and how each country’s mineral industry relates to U.S. industry. Most chapters include production tables and industry structure tables, information about Government policies and programs that affect the country’s mineral industry, and an outlook section.The USGS continually strives to improve the value of its publications to users. Constructive comments and suggestions by readers of the Minerals Yearbook are welcomed.

Minerals Yearbook, volume III, Area Reports—International

Science.gov (United States)

,

2018-01-01

The U.S. Geological Survey (USGS) Minerals Yearbook discusses the performance of the worldwide minerals and materials industries and provides background information to assist in interpreting that performance. Content of the individual Minerals Yearbook volumes follows:Volume I, Metals and Minerals, contains chapters about virtually all metallic and industrial mineral commodities important to the U.S. economy. Chapters on survey methods, summary statistics for domestic nonfuel minerals, and trends in mining and quarrying in the metals and industrial mineral industries in the United States are also included.Volume II, Area Reports: Domestic, contains a chapter on the mineral industry of each of the 50 States and Puerto Rico and the Administered Islands. This volume also has chapters on survey methods and summary statistics of domestic nonfuel minerals.Volume III, Area Reports: International, is published as four separate reports. These regional reports contain the latest available minerals data on more than 180 foreign countries and discuss the importance of minerals to the economies of these nations and the United States. Each report begins with an overview of the region’s mineral industries during the year. It continues with individual country chapters that examine the mining, refining, processing, and use of minerals in each country of the region and how each country’s mineral industry relates to U.S. industry. Most chapters include production tables and industry structure tables, information about Government policies and programs that affect the country’s mineral industry, and an outlook section.The USGS continually strives to improve the value of its publications to users. Constructive comments and suggestions by readers of the Minerals Yearbook are welcomed.

pH-zone-refining elution-extrusion countercurrent chromatography: Separation of hydroxyanthraquinones from Cassiae semen.

Science.gov (United States)

Bu, Zhisi; Lv, Liqiong; Li, Xingnuo; Chu, Chu; Tong, Shengqiang

2017-11-01

Seven hydroxyanthraquinones were successfully separated from the traditional Chinese medicinal herb Cassiae semen by conventional and pH-zone-refining countercurrent chromatography with an environmentally friendly biphasic solvent system, in which elution-extrusion mode was investigated for pH-zone-refining countercurrent chromatography for the first time. A two-phase solvent system composed of n-hexane/ethyl acetate/ethanol/water (5:3:4:4, v/v/v/v) was used for the conventional countercurrent chromatography while the same system with a different volume ratio n-hexane/ethyl acetate/ethanol/water (3:5:2:6, v/v/v/v) was used for pH-zone-refining countercurrent chromatography, in which 20 mmol/L of trifluoroacetic acid was added in the organic phase as a retainer and 15 mmol/L of ammonia was added to the aqueous phase as an eluter. A 400 mg crude sample could be well separated by pH-zone-refining countercurrent chromatography, yielding 53 mg of aurantio-obtusin, 40 mg of chryso-obtusin, 18 mg of obtusin, 24 mg of obtusifolin, 10 mg of emodin, and 105 mg of the mixture of chrysophanol and physcion with a purity of over 95.8, 95.7, 96.9, 93.5, 97.4, 77.1, and 19.8%, as determined by high-performance liquid chromatography. Furthermore, the difference in elution sequence between conventional and pH-zone-refining mode was observed and discussed. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Trajectory Optimization Based on Multi-Interval Mesh Refinement Method

Directory of Open Access Journals (Sweden)

Ningbo Li

2017-01-01

Full Text Available In order to improve the optimization accuracy and convergence rate for trajectory optimization of the air-to-air missile, a multi-interval mesh refinement Radau pseudospectral method was introduced. This method made the mesh endpoints converge to the practical nonsmooth points and decreased the overall collocation points to improve convergence rate and computational efficiency. The trajectory was divided into four phases according to the working time of engine and handover of midcourse and terminal guidance, and then the optimization model was built. The multi-interval mesh refinement Radau pseudospectral method with different collocation points in each mesh interval was used to solve the trajectory optimization model. Moreover, this method was compared with traditional h method. Simulation results show that this method can decrease the dimensionality of nonlinear programming (NLP problem and therefore improve the efficiency of pseudospectral methods for solving trajectory optimization problems.

COBRA-SFS [Spent Fuel Storage]: A thermal-hydraulic analysis computer code: Volume 1, Mathematical models and solution method

International Nuclear Information System (INIS)

Rector, D.R.; Wheeler, C.L.; Lombardo, N.J.

1986-11-01

COBRA-SFS (Spent Fuel Storage) is a general thermal-hydraulic analysis computer code used to predict temperatures and velocities in a wide variety of systems. The code was refined and specialized for spent fuel storage system analyses for the US Department of Energy's Commercial Spent Fuel Management Program. The finite-volume equations governing mass, momentum, and energy conservation are written for an incompressible, single-phase fluid. The flow equations model a wide range of conditions including natural circulation. The energy equations include the effects of solid and fluid conduction, natural convection, and thermal radiation. The COBRA-SFS code is structured to perform both steady-state and transient calculations: however, the transient capability has not yet been validated. This volume describes the finite-volume equations and the method used to solve these equations. It is directed toward the user who is interested in gaining a more complete understanding of these methods

Refined geometric transition and qq-characters

Science.gov (United States)

Kimura, Taro; Mori, Hironori; Sugimoto, Yuji

2018-01-01

We show the refinement of the prescription for the geometric transition in the refined topological string theory and, as its application, discuss a possibility to describe qq-characters from the string theory point of view. Though the suggested way to operate the refined geometric transition has passed through several checks, it is additionally found in this paper that the presence of the preferred direction brings a nontrivial effect. We provide the modified formula involving this point. We then apply our prescription of the refined geometric transition to proposing the stringy description of doubly quantized Seiberg-Witten curves called qq-characters in certain cases.

Refinement, testing, and application of an Integrated Data Assimilation/Sounding System (IDASS) for the DOE/ARM Experimental Program. Final report for period September 20, 1990 - May 8, 1997

Energy Technology Data Exchange (ETDEWEB)

Parsons, David B.

2002-04-09

This report describes work done by NCAR under the ''Refinement, Testing, and Application of an Integrated Data Assimilation/Sounding System (IDASS) for the DOE/ARM Experimental Program''. It includes a discussion of the goals, findings and a list of 27 journal articles, 92 non-refereed papers and 30 other presentations not associated with a formal publication.

Proceedings of the 1995 U.S. DOE hydrogen program review. Volume II

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-09-01

The 1995 US DOE Hydrogen Program Review was held April 18-21, 1995 in Coral Gables, FL. Volume II of the Proceedings contains 8 papers presented under the subject of hydrogen storage and 17 papers presented on hydrogen production. Selected papers are indexed separately for inclusion in the Energy Science and Technology Database.

Proceedings of the 1998 U.S. DOE Hydrogen Program Review: Volume 2

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-08-01

This document contains technical progress reports on 42 research projects funded by the DOE Hydrogen Program in Fiscal Year 1998, in support of its mission to make hydrogen a cost-effective energy carrier for utility, building, and transportation applications. Each year, the Program conducts a rigorous review of its portfolio of projects, utilizing teams of experts to provide vital feedback on the progress of research. These proceedings serve as an important technology reference for the DOE Hydrogen Program. The papers in Volume 2 are arranged under the following topical sections: Storage and separation systems; Thermal systems; and Transportation systems. Selected papers have been indexed separately for inclusion in the Energy Science and Technology Database.

Spatially adaptive hp refinement approach for PN neutron transport equation using spectral element method

International Nuclear Information System (INIS)

Nahavandi, N.; Minuchehr, A.; Zolfaghari, A.; Abbasi, M.

2015-01-01

Highlights: • Powerful hp-SEM refinement approach for P N neutron transport equation has been presented. • The method provides great geometrical flexibility and lower computational cost. • There is a capability of using arbitrary high order and non uniform meshes. • Both posteriori and priori local error estimation approaches have been employed. • High accurate results are compared against other common adaptive and uniform grids. - Abstract: In this work we presented the adaptive hp-SEM approach which is obtained from the incorporation of Spectral Element Method (SEM) and adaptive hp refinement. The SEM nodal discretization and hp adaptive grid-refinement for even-parity Boltzmann neutron transport equation creates powerful grid refinement approach with high accuracy solutions. In this regard a computer code has been developed to solve multi-group neutron transport equation in one-dimensional geometry using even-parity transport theory. The spatial dependence of flux has been developed via SEM method with Lobatto orthogonal polynomial. Two commonly error estimation approaches, the posteriori and the priori has been implemented. The incorporation of SEM nodal discretization method and adaptive hp grid refinement leads to high accurate solutions. Coarser meshes efficiency and significant reduction of computer program runtime in comparison with other common refining methods and uniform meshing approaches is tested along several well-known transport benchmarks

On Modal Refinement and Consistency

DEFF Research Database (Denmark)

Nyman, Ulrik; Larsen, Kim Guldstrand; Wasowski, Andrzej

2007-01-01

Almost 20 years after the original conception, we revisit several fundamental question about modal transition systems. First, we demonstrate the incompleteness of the standard modal refinement using a counterexample due to Hüttel. Deciding any refinement, complete with respect to the standard...

Decontamination of metals by melt refining/slagging: First year progress report

International Nuclear Information System (INIS)

Mizia, R.E.; Worcester, S.A.; Twidwell, L.G.; Paolini, D.J.; Weldon, T.A.

1994-03-01

As the number of nuclear installations undergoing decontamination and decommissioning (D ampersand D) increases, current radioactive waste storage space is consumed and establishment of new waste storage areas becomes increasingly difficult. The problem of handling and storing radioactive scrap metal (RSM) gains increasing importance in the DOE Environmental Restoration and Waste Management Program. To alleviate present and future waste storage problems, Westinghouse Idaho Nuclear Company (WINCO) is managing a program for the recycling of RSM for beneficial use within the DOE complex. As part of that effort, Montana Tech has been awarded a contract to help optimize melting and refining technologies for the recycling of stainless steel RSM. The scope of the Montana Tech program includes a literature survey, a decontaminating slag design study, small scale melting studies to determine optimum slag compositions for removal of radioactive contaminant surrogates, analysis of preferred melting techniques, and coordination of pilot scale melting demonstrations (100-500 lbs) to be conducted at selected commercial facilities. This program will identify methods that can be used to recycle stainless steel RSM which will be used to fabricate high and low level waste canisters for the Idaho Waste Immobilization Facility. This report summarizes the results of an extensive literature review and the first year's progress on slag design, small-scale melt refining of surrogate-containing stainless steel (presently only a three month effort), and pilot-scale preparation of surrogate master ingots

Refining - Panorama 2008

International Nuclear Information System (INIS)

2008-01-01

Investment rallied in 2007, and many distillation and conversion projects likely to reach the industrial stage were announced. With economic growth sustained in 2006 and still pronounced in 2007, oil demand remained strong - especially in emerging countries - and refining margins stayed high. Despite these favorable business conditions, tensions persisted in the refining sector, which has fallen far behind in terms of investing in refinery capacity. It will take renewed efforts over a long period to catch up. Looking at recent events that have affected the economy in many countries (e.g. the sub-prime crisis), prudence remains advisable

SMACS - a system of computer programs for probabilistic seismic analysis of structures and subsystems. Volume II. Example problem

International Nuclear Information System (INIS)

Maslenikov, O.R.; Johnson, J.J.; Tiong, L.W.; Mraz, M.J.; Bumpus, S.; Gerhard, M.A.

1985-03-01

In this volume of the SMACS User's Manual an example problem is presented to demonstrate the type of problem that SMACS is capable of solving and to familiarize the user with format of the various data files involved. This volume is organized into thirteen appendices which follow a short description of the problem. Each appendix contains listings of the input and output files associated with each computer run that was necessary to solve the problem. In cases where one SMACS program uses data generated by another SMACS program, the data file is shown in the appendix for the programs which generated it

A method for refining oil

Energy Technology Data Exchange (ETDEWEB)

Bruskin, Yu.A.; Gorokhov, V.V.; Kotler, L.D.; Kovalenko, N.F.; Spasskiy, Yu.B.; Titov, A.M.; Vlasenko, V.Ye.; Vytnov, V.A.

1983-01-01

In the method for refining oil through its distillation with the isolation of directly distilled gases and a benzine fraction (BS) with the use of a benzine fraction pyrolysis, in order to increase the output of the lower olefines and to reduce the energy expenditures, the distillation is conducted with the isolation of 10 to 40 percent of the benzine fraction from its potential content along with the directly distilled gases. The obtained mixture of the remaining part of the benzine fraction is absorbed at a pressure of 1.5 to 6 atmospheres with the feeding of the obtained saturated absorbent to pyrolysis and subsequent mixing of the obtained pyrolysis gas with the unabsorbed product and their joint gas division. As compared to the known method, the proposed method makes it possible to reduce the energy expenditures which is achieved through a reduction in the volume of irrigation in the tower, and to increase the output of the olefines through processing of the steam and gas mixture of the benzine and the directly distilled gases.

Oil Production, Refining and Transportation in Canada

Directory of Open Access Journals (Sweden)

Igbal A. Guliyev

2015-01-01

Full Text Available The article deals with fuel and energy complex of Canada as one of the largest manufacturers of primary energy in the world, which provides up to 6 percent of the world energy supply. Only the Russian Federation, PRC, the United States of America and the Kingdom of Saudi Arabia have larger production volumes. However, oil plays the most significant role in Canada's energy exports. It is estimated that its proven reserves are sufficient to meet the demand for 140 years at current production rate. The relevance of the study, including the analysis of fuel and energy complex of Canada, is due to the fact that such comparison and synthesis of data on the amount of recoverable oil reserves, the volume of its production, imports, exports and transit of oil and oil products, the distribution of oil for transportation (via pipelines, rail, sea, road, strategic oil field, refining and transportation of oil and oil products development projects, as well as implementation of Canada's best practices in the Russian Federation, is being developed for the first time. In addition, the data given in previously published articles on the subject, due to the dynamic development of the industry, are obsolete and do not reflect the real situation.

Refinement by interface instantiation

DEFF Research Database (Denmark)

Hallerstede, Stefan; Hoang, Thai Son

2012-01-01

be easily refined. Our first contribution hence is a proposal for a new construct called interface that encapsulates the external variables, along with a mechanism for interface instantiation. Using the new construct and mechanism, external variables can be refined consistently. Our second contribution...... is an approach for verifying the correctness of Event-B extensions using the supporting Rodin tool. We illustrate our approach by proving the correctness of interface instantiation....

The use of Fourier reverse transforms in crystallographic phase refinement

Energy Technology Data Exchange (ETDEWEB)

Ringrose, Sharon [Iowa State Univ., Ames, IA (United States)

1997-10-08

Often a crystallographer obtains an electron density map which shows only part of the structure. In such cases, the phasing of the trial model is poor enough that the electron density map may show peaks in some of the atomic positions, but other atomic positions are not visible. There may also be extraneous peaks present which are not due to atomic positions. A method for determination of crystal structures that have resisted solution through normal crystallographic methods has been developed. PHASER is a series of FORTRAN programs which aids in the structure solution of poorly phased electron density maps by refining the crystallographic phases. It facilitates the refinement of such poorly phased electron density maps for difficult structures which might otherwise not be solvable. The trial model, which serves as the starting point for the phase refinement, may be acquired by several routes such as direct methods or Patterson methods. Modifications are made to the reverse transform process based on several assumptions. First, the starting electron density map is modified based on the fact that physically the electron density map must be non-negative at all points. In practice a small positive cutoff is used. A reverse Fourier transform is computed based on the modified electron density map. Secondly, the authors assume that a better electron density map will result by using the observed magnitudes of the structure factors combined with the phases calculated in the reverse transform. After convergence has been reached, more atomic positions and less extraneous peaks are observed in the refined electron density map. The starting model need not be very large to achieve success with PHASER; successful phase refinement has been achieved with a starting model that consists of only 5% of the total scattering power of the full molecule. The second part of the thesis discusses three crystal structure determinations.

40 CFR 80.250 - How is the small refiner sulfur baseline and volume determined?

Science.gov (United States)

2010-07-01

...=Baseline volume. VI=Volume of gasoline batch i. n = Total number of batches of gasoline produced from....245(a)(3); or, for a foreign refinery, the total number of batches of gasoline produced and imported... gasoline produced and imported into the U.S. pursuant to § 80.245(c)(2)). i = Individual batch of gasoline...

The relationship between viscosity and refinement efficiency of pure aluminum by Al-Ti-B refiner

Energy Technology Data Exchange (ETDEWEB)

Yu Lina [Key Laboratory of Liquid Structure and Heredity of Materials, Ministry of Education, Shandong University, 73 Jingshi Road, Jinan 250061 (China); Liu Xiangfa [Key Laboratory of Liquid Structure and Heredity of Materials, Ministry of Education, Shandong University, 73 Jingshi Road, Jinan 250061 (China)]. E-mail: xfliu@sdu.edu.cn

2006-11-30

The relationship between viscosity and refinement efficiency of pure aluminum with the addition of Al-Ti-B master alloy was studied in this paper. The experimental results show that when the grain size of solidified sample is finer the viscosity of the melt is higher after the addition of different Al-Ti-B master alloys. This indicates that viscosity can be used to approximately estimate the refinement efficiency of Al-Ti-B refiners in production to a certain extent. The main reason was also discussed in this paper by using transmission electron microscopy (TEM) analysis and differential scanning calorimetry (DSC) experiment.

Relational Demonic Fuzzy Refinement

OpenAIRE

Tchier, Fairouz

2014-01-01

We use relational algebra to define a refinement fuzzy order called demonic fuzzy refinement and also the associated fuzzy operators which are fuzzy demonic join $({\\bigsqcup }_{\\mathrm{\\text{f}}\\mathrm{\\text{u}}\\mathrm{\\text{z}}})$ , fuzzy demonic meet $({\\sqcap }_{\\mathrm{\\text{f}}\\mathrm{\\text{u}}\\mathrm{\\text{z}}})$ , and fuzzy demonic composition $({\\square }_{\\mathrm{\\text{f}}\\mathrm{\\text{u}}\\mathrm{\\text{z}}})$ . Our definitions and properties are illustrated by some examples using ma...

Proceedings of the Advanced Turbine Systems Annual Program Review meeting. Volume 1

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-10-01

Goal of the 8-year program is to develop cleaner, more efficient, and less expensive gas turbine systems for utility and industrial electric power generation, cogeneration, and mechanical drive units. The conference is held annually for energy executives, engineers, scientists, and other interested parties industry, academia, and Government. Advanced turbine systems topics discussed during five technical sessions included policy and strategic issues, program element overviews and technical reviews, related activities, university/industry consortium interactions, and supportive projects. Twenty-one papers presented during the technical sessions are contained in this volume; they are processed separately for the data base.

Nuclear proliferation and civilian nuclear power. Report of the Nonproliferation Alternative Systems Assessment Program. Volume II. Proliferation resistance

International Nuclear Information System (INIS)

1980-06-01

The purpose of this volume is limited to an assessment of the relative effects that particular choices of nuclear-power systems, for whatever reasons, may have on the possible spread of nuclear-weapons capabilities. This volume addresses the concern that non-nuclear-weapons states may be able to initiate efforts to acquire or to improve nuclear-weapons capabilities through civilian nuclear-power programs; it also addresses the concern that subnational groups may obtain and abuse the nuclear materials or facilities of such programs, whether in nuclear-weapons states (NWS's) or nonnuclear-weapons states (NNW's). Accordingly, this volume emphasizes one important factor in such decisions, the resistance of nuclear-power systems to the proliferation of nuclear-weapons capabilities

ALBEMO, a program for the calculation of the radiation transport in void volumes with reflecting walls

International Nuclear Information System (INIS)

Mueller, K.; Vossebrecker, H.

The Monte Carlo Program ALBEMO calculates the distribution of neutrons and gamma rays in void volumes which are bounded by reflecting walls with x, y, z coordinates. The program is based on the albedo method. The effect of significant simplifying assumptions is investigated. Comparisons with experiments show satisfying agreement

Subseabed disposal program annual report, January-December 1980. Volume II. Appendices (principal investigator progress reports). Part 1

International Nuclear Information System (INIS)

Hinga, K.R.

1981-07-01

Volume II of the sixth annual report describing the progress and evaluating the status of the Subseabed Disposal Program contains the appendices referred to in Volume I, Summary and Status. Because of the length of Volume II, it has been split into two parts for publication purposes. Part 1 contains Appendices A-Q; Part 2 contains Appendices R-MM. Separate abstracts have been prepared for each appendix for inclusion in the Energy Data Base

Subseabed disposal program annual report, January-December 1980. Volume II. Appendices (principal investigator progress reports). Part 1

Energy Technology Data Exchange (ETDEWEB)

Hinga, K.R. (ed.)

1981-07-01

Volume II of the sixth annual report describing the progress and evaluating the status of the Subseabed Disposal Program contains the appendices referred to in Volume I, Summary and Status. Because of the length of Volume II, it has been split into two parts for publication purposes. Part 1 contains Appendices A-Q; Part 2 contains Appendices R-MM. Separate abstracts have been prepared for each appendix for inclusion in the Energy Data Base.

Quality assurance program manual for nuclear power plants. Volume I. Policies

International Nuclear Information System (INIS)

1976-01-01

The Consumers Power Company Quality Assurance Program Manual for Nuclear Power Plants consists of policies and procedures which comply with current NRC regulatory requirements and industry codes and standards in effect during the design, procurement, construction, testing, operation, refueling, maintenance, repair and modification activities associated with nuclear power plants. Specific NRC and industry documents that contain the requirements, including the issue dates in effect, are identified in each nuclear power plant's Safety Analysis Report. The requirements established by these documents form the basis for the Consumer Power Quality Assurance Program, which is implemented to control those structures, systems, components and operational safety actions listed in each nuclear power plant's Quality List (Q-List). As additional and revised requirements are issued by the NRC and professional organizations involved in nuclear activities, they will be reviewed for their impact on this manual, and changes will be made where considered necessary. CP Co 1--Consumers Power Company QA Program Topical Report is Volume I of this manual and contains Quality Assurance Program Policies applicable during all phases of nuclear power plant design, construction and operation

Production of Al-Ti-B grain refining master alloys from Na2B4O7 and K2TiF6

International Nuclear Information System (INIS)

Birol, Yuecel

2008-01-01

It is very desirable to replace the KBF 4 salt in the popular 'halide salt' process to reduce the volume of fluoride salts to be added to molten aluminium in the production of Al-Ti-B grain refiners. Being over 2 times richer in B, Na 2 B 4 O 7 is a promising replacement for KBF 4 , and is used in the present work to produce Al-Ti-B grain refiner master alloys. A fraction of the aluminide particles were entrapped in the spent salt giving a relatively lower Ti recovery when KBF 4 was replaced by Na 2 B 4 O 7 . The grain refining performance of the Al-Ti-B grain refiner alloy thus produced was nevertheless acceptable. The spent salt became too viscous with the oxides, aluminides and borides to be removed by decanting when Na 2 B 4 O 7 .5H 2 O was used to supply boron. The viscous spent salt, entrained in the grain refiner alloy, did not only impair its performance, but also hurt the fluidity of the molten alloy and made pouring difficult

Panorama 2007: Refining and Petrochemicals

International Nuclear Information System (INIS)

Silva, C.

2007-01-01

The year 2005 saw a new improvement in refining margins that continued during the first three quarters of 2006. The restoration of margins in the last three years has allowed the refining sector to regain its profitability. In this context, the oil companies reported earnings for fiscal year 2005 that were up significantly compared to 2004, and the figures for the first half-year 2006 confirm this trend. Despite this favorable business environment, investments only saw a minimal increase in 2005 and the improvement expected for 2006 should remain fairly limited. Looking to 2010-2015, it would appear that the planned investment projects with the highest probability of reaching completion will be barely adequate to cover the increase in demand. Refining sector should continue to find itself under pressure. As for petrochemicals, despite a steady up-trend in the naphtha price, the restoration of margins consolidated a comeback that started in 2005. All in all, capital expenditure remained fairly low in both the refining and petrochemicals sectors, but many projects are planned for the next ten years. (author)

EPRI tailored collaboration 3 Calvert Cliffs cost and volume reduction program

International Nuclear Information System (INIS)

Rigsby, M.D.; Watson, B.A.

1995-01-01

Baltimore Gas ampersand Electric's (BGE) Calvert Cliffs Nuclear Power Plant (CCNPP) is a two unit PWR located approximately 60 miles south of Baltimore, Maryland on the Chesapeake Bay. Both units are of Combustion Engineering design, Unit 1 began commercial operation is 1975 and Unit 2 in 1978. BGE contracted with EPRI to participate in the industry initiative to reduce low-level waste volumes with the expectation to: (1) Reduce O ampersand M costs through LLRW reduction by lowering the volume requiring processing, transportation, and storage/disposal. (2) Manage responsibility available resources; i.e., material, equipment, personnel, etc., through segregation. decontamination, recycling and worker awareness. (3) Improve Calvert Cliff's positive image in the community by minimizing the impact on the environment through generating less LLRW. Baltimore Gas ampersand Electric is committed to effective management of low-level radioactive waste (LLRW) at the Calvert Cliffs Nuclear Power Plant. Established Nuclear Program Policies and Procedures support CCNPP's commitment to minimizing generation of low-level radioactive waste (LLRW). Since the mid 1980's, CCNPP has made progress in reducing the volume of LLRW generated and disposed. EPRI's onsite assessment and subsequent assistance pointed out several areas for improvement

Refining margins: recent trends

International Nuclear Information System (INIS)

Baudoin, C.; Favennec, J.P.

1999-01-01

Despite a business environment that was globally mediocre due primarily to the Asian crisis and to a mild winter in the northern hemisphere, the signs of improvement noted in the refining activity in 1996 were borne out in 1997. But the situation is not yet satisfactory in this sector: the low return on invested capital and the financing of environmental protection expenditure are giving cause for concern. In 1998, the drop in crude oil prices and the concomitant fall in petroleum product prices was ultimately rather favorable to margins. Two elements tended to put a damper on this relative optimism. First of all, margins continue to be extremely volatile and, secondly, the worsening of the economic and financial crisis observed during the summer made for a sharp decline in margins in all geographic regions, especially Asia. Since the beginning of 1999, refining margins are weak and utilization rates of refining capacities have decreased. (authors)

40 CFR 80.1285 - How does a refiner apply for a benzene baseline?

Science.gov (United States)

2010-07-01

... baseline? 80.1285 Section 80.1285 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... (abt) Program § 80.1285 How does a refiner apply for a benzene baseline? (a) A benzene baseline... credits. (b) For U.S. Postal delivery, the benzene baseline application shall be sent to: Attn: MSAT2...

Panorama 2009 - refining

International Nuclear Information System (INIS)

2008-01-01

For oil companies to invest in new refining and conversion capacity, favorable conditions over time are required. In other words, refining margins must remain high and demand sustained over a long period. That was the situation prevailing before the onset of the financial crisis in the second half of 2008. The economic conjuncture has taken a substantial turn for the worse since then and the forecasts for 2009 do not look bright. Oil demand is expected to decrease in the OECD countries and to grow much more slowly in the emerging countries. It is anticipated that refining margins will fall in 2009 - in 2008, they slipped significantly in the United States - as a result of increasingly sluggish demand, especially for light products. The next few months will probably be unfavorable to investment. In addition to a gloomy business outlook, there may also be a problem of access to sources of financing. As for investment projects, a mainstream trend has emerged in the last few years: a shift away from the regions that have historically been most active (the OECD countries) towards certain emerging countries, mostly in Asia or the Middle East. The new conjuncture will probably not change this trend

Environmental control technology for mining, milling, and refining thorium

International Nuclear Information System (INIS)

Weakley, S.A.; Blahnik, D.E.; Young, J.K.; Bloomster, C.H.

1980-02-01

The purpose of this report is to evaluate, in terms of cost and effectiveness, the various environmental control technologies that would be used to control the radioactive wastes generated in the mining, milling, and refining of thorium from domestic resources. The technologies, in order to be considered for study, had to reduce the radioactivity in the waste streams to meet Atomic Energy Commission (10 CFR 20) standards for natural thorium's maximum permissible concentration (MPC) in air and water. Further regulatory standards or licensing requirements, either federal, state, or local, were not examined. The availability and cost of producing thorium from domestic resources is addressed in a companion volume. The objectives of this study were: (1) to identify the major waste streams generated during the mining, milling, and refining of reactor-grade thorium oxide from domestic resources; and (2) to determine the cost and levels of control of existing and advanced environmental control technologies for these waste streams. Six potential domestic deposits of thorium oxide, in addition to stockpiled thorium sludges, are discussed in this report. A summary of the location and characteristics of the potential domestic thorium resources and the mining, milling, and refining processes that will be needed to produce reactor-grade thorium oxide is presented in Section 2. The wastes from existing and potential domestic thorium oxide mines, mills, and refineries are identified in Section 3. Section 3 also presents the state-of-the-art technology and the costs associated with controlling the wastes from the mines, mills, and refineries. In Section 4, the available environmental control technologies for mines, mills, and refineries are assessed. Section 5 presents the cost and effectiveness estimates for the various environmental control technologies applicable to the mine, mill, and refinery for each domestic resource

40 CFR 80.335 - What gasoline sample retention requirements apply to refiners and importers?

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 16 2010-07-01 2010-07-01 false What gasoline sample retention... PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) REGULATION OF FUELS AND FUEL ADDITIVES Gasoline Sulfur Sampling, Testing and Retention Requirements for Refiners and Importers § 80.335 What gasoline sample...

Proceedings of the Advanced Turbine Systems Annual Program Review meeting. Volume 2

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-10-01

Goal of the 8-year program are to develop cleaner, more efficient, and less expensive gas turbine systems for utility and industrial electric power generation, cogeneration, and mechanical drive units. The conference is held annually for energy executives, engineers, scientists, and other interested parties in industry, academia, and Government. This volume contains 28 poster presentations and appendices; the poster papers are processed separately for the data base.

Development of computer program for the economic evaluation of the volume reduction system for the low-level radwaste

International Nuclear Information System (INIS)

Yang, Jin Yeong

1994-02-01

This study provides the basis for investigating the benefits of purchasing volume reduction equipment and includes the establishment of a volume reduction data base, the creation of the volume reduction cost analysis computer program PEEVR (Program of Economic Evaluation for the Volume Reduction), and a generic analysis designed to identify the major costs influencing the economics of the various equipment options. In treating the plant types and the wastes, this study considers that condensate polishing system is included or not in PWR and precoat condensate polishing system, deep bed condensate polishing system in BWR and the 5 waste streams, i.e., compatible trash (COTRASH), ion exchange resin (IXRESIN), concentrate liquid (CONCLIQ), filter sludge (FSLUDGE), non compatible trash (COTRASH). This study uses the PVRR and LRR methods to create cost analysis and performs sensitivity analysis for the each cost variable and shows that future burial costs increases are the major factors in the economic evaluation

Romanian refining industry assesses restructuring

International Nuclear Information System (INIS)

Tanasescu, D.G.

1991-01-01

The Romanian crude oil refining industry, as all the other economic sectors, faces the problems accompanying the transition from a centrally planned economy to a market economy. At present, all refineries have registered as joint-stock companies and all are coordinated and assisted by Rafirom S.A., from both a legal and a production point of view. Rafirom S.A. is a joint-stock company that holds shares in refineries and other stock companies with activities related to oil refining. Such activities include technological research, development, design, transportation, storage, and domestic and foreign marketing. This article outlines the market forces that are expected to: drive rationalization and restructuring of refining operations and define the targets toward which the reconfigured refineries should strive

National low-level waste management program radionuclide report series, Volume 14: Americium-241

International Nuclear Information System (INIS)

Winberg, M.R.; Garcia, R.S.

1995-09-01

This report, Volume 14 of the National Low-Level Waste Management Program Radionuclide Report Series, discusses the radiological and chemical characteristics of americium-241 ( 241 Am). This report also includes discussions about waste types and forms in which 241 Am can be found and 241 Am behavior in the environment and in the human body

National Low-Level Waste Management Program radionuclide report series. Volume 13, Curium-242

International Nuclear Information System (INIS)

Adams, J.P.

1995-08-01

This report, Volume 13 of the National Low-Level Waste Management Program Radionuclide Report Series, discusses the radiological and chemical characteristics of curium-242 ( 242 Cm). This report also includes discussions about waste types and forms in which 242 Cm can be found and 242 Cm behavior in the environment and in the human body

Dependence of Achievable Plan Quality on Treatment Technique and Planning Goal Refinement: A Head-and-Neck Intensity Modulated Radiation Therapy Application

International Nuclear Information System (INIS)

Qi, X. Sharon; Ruan, Dan; Lee, Steve P.; Pham, Andrew; Kupelian, Patrick; Low, Daniel A.; Steinberg, Michael; Demarco, John

2015-01-01

Purpose: To develop a practical workflow for retrospectively analyzing target and normal tissue dose–volume endpoints for various intensity modulated radiation therapy (IMRT) delivery techniques; to develop technique-specific planning goals to improve plan consistency and quality when feasible. Methods and Materials: A total of 165 consecutive head-and-neck patients from our patient registry were selected and retrospectively analyzed. All IMRT plans were generated using the same dose–volume guidelines for TomoTherapy (Tomo, Accuray), TrueBeam (TB, Varian) using fixed-field IMRT (TB-IMRT) or RAPIDARC (TB-RAPIDARC), or Siemens Oncor (Siemens-IMRT, Siemens). A MATLAB-based dose–volume extraction and analysis tool was developed to export dosimetric endpoints for each patient. With a fair stratification of patient cohort, the variation of achieved dosimetric endpoints was analyzed among different treatment techniques. Upon identification of statistically significant variations, technique-specific planning goals were derived from dynamically accumulated institutional data. Results: Retrospective analysis showed that although all techniques yielded comparable target coverage, the doses to the critical structures differed. The maximum cord doses were 34.1 ± 2.6, 42.7 ± 2.1, 43.3 ± 2.0, and 45.1 ± 1.6 Gy for Tomo, TB-IMRT, TB-RAPIDARC, and Siemens-IMRT plans, respectively. Analyses of variance showed significant differences for the maximum cord doses but no significant differences for other selected structures among the investigated IMRT delivery techniques. Subsequently, a refined technique-specific dose–volume guideline for maximum cord dose was derived at a confidence level of 95%. The dosimetric plans that failed the refined technique-specific planning goals were reoptimized according to the refined constraints. We observed better cord sparing with minimal variations for the target coverage and other organ at risk sparing for the Tomo cases, and higher

Action Refinement

NARCIS (Netherlands)

Gorrieri, R.; Rensink, Arend; Bergstra, J.A.; Ponse, A.; Smolka, S.A.

2001-01-01

In this chapter, we give a comprehensive overview of the research results in the field of action refinement during the past 12 years. The different approaches that have been followed are outlined in detail and contrasted to each other in a uniform framework. We use two running examples to discuss

Office of Technology Development's Research, Development, Demonstration, Testing and Evaluation Mid-Year Program Review. Volume 2

International Nuclear Information System (INIS)

1994-01-01

This document, Volume 2, presents brief summaries of programs being investigated at USDOE sites for waste processing, remedial action, underground storage tank remediation, and robotic applications in waste management

Industrial Sector Technology Use Model (ISTUM): industrial energy use in the United States, 1974-2000. Volume 1. Primary model documentation. Final report

Energy Technology Data Exchange (ETDEWEB)

Bohn, Roger E.; Herod, J. Steven; Andrews, Gwen L.; Budzik, Philip M.; Eissenstat, Richard S.; Grossmann, John R.; Reiner, Gary M.; Roschke, Thomas E.; Shulman, Michael J.; Toppen, Timothy R.; Veno, William R.; Violette, Daniel M.; Smolinski, Michael D.; Habel, Deborah; Cook, Alvin E.

1979-10-01

ISTUM is designed to predict the commercial market penetration of various energy technologies in the industrial sector out to the year 2000. It is a refinement and further development of Market Oriented Program Planning Study task force in 1977. ISTUM assesses the comparative economic competitiveness of each technology and competes over 100 energy technologies - conventionals, fossil/energy, conservation, cogeneration, solar, and geothermal. A broad overview of the model, the solution of the model, and an in-depth discussion of strength and limitations of the model are provided in Volume I. (MCW)

Optimization of Refining Craft for Vegetable Insulating Oil

Science.gov (United States)

Zhou, Zhu-Jun; Hu, Ting; Cheng, Lin; Tian, Kai; Wang, Xuan; Yang, Jun; Kong, Hai-Yang; Fang, Fu-Xin; Qian, Hang; Fu, Guang-Pan

2016-05-01

Vegetable insulating oil because of its environmental friendliness are considered as ideal material instead of mineral oil used for the insulation and the cooling of the transformer. The main steps of traditional refining process included alkali refining, bleaching and distillation. This kind of refining process used in small doses of insulating oil refining can get satisfactory effect, but can't be applied to the large capacity reaction kettle. This paper using rapeseed oil as crude oil, and the refining process has been optimized for large capacity reaction kettle. The optimized refining process increases the acid degumming process. The alkali compound adds the sodium silicate composition in the alkali refining process, and the ratio of each component is optimized. Add the amount of activated clay and activated carbon according to 10:1 proportion in the de-colorization process, which can effectively reduce the oil acid value and dielectric loss. Using vacuum pumping gas instead of distillation process can further reduce the acid value. Compared some part of the performance parameters of refined oil products with mineral insulating oil, the dielectric loss of vegetable insulating oil is still high and some measures are needed to take to further optimize in the future.

Grain refining efficiency of Al-Ti-C alloys

International Nuclear Information System (INIS)

Birol, Yuecel

2006-01-01

The problems associated with boride agglomeration and the poisoning effect of Zr in Zr-bearing alloys have created a big demand for boron-free grain refiners. The potential benefits of TiC as a direct nucleant for aluminium grains have thus generated a great deal of interest in TiC-bearing alloys in recent years. In Al-Ti-C grain refiners commercially available today, Al 3 Ti particles are introduced into the melt along with the TiC particles. Since the latter are claimed to nucleate α-Al directly, it is of great technological interest to see if reducing the Ti:C ratio further, i.e., increasing the C content of the grain refiner, will produce an increase in the grain refining efficiency of these alloys. A series of grain refiner samples with the Ti concentration fixed at 3% and a range of C contents between 0 and 0.75 were obtained by appropriately mixing an experimental Al-3Ti-0.75C alloy with Al-10Ti alloy and commercial purity aluminium. The grain refining efficiency of these grain refiners was assessed to investigate the role of the insoluble TiC and the soluble Al 3 Ti particles. The optimum chemistry for the Al-Ti-C grain refiners was also identified

Grain refining efficiency of Al-Ti-C alloys

Energy Technology Data Exchange (ETDEWEB)

Birol, Yuecel [Materials Institute, Marmara Research Center, TUBITAK, 41470 Gebze, Kocaeli (Turkey)]. E-mail: yucel.birol@mam.gov.tr

2006-09-28

The problems associated with boride agglomeration and the poisoning effect of Zr in Zr-bearing alloys have created a big demand for boron-free grain refiners. The potential benefits of TiC as a direct nucleant for aluminium grains have thus generated a great deal of interest in TiC-bearing alloys in recent years. In Al-Ti-C grain refiners commercially available today, Al{sub 3}Ti particles are introduced into the melt along with the TiC particles. Since the latter are claimed to nucleate {alpha}-Al directly, it is of great technological interest to see if reducing the Ti:C ratio further, i.e., increasing the C content of the grain refiner, will produce an increase in the grain refining efficiency of these alloys. A series of grain refiner samples with the Ti concentration fixed at 3% and a range of C contents between 0 and 0.75 were obtained by appropriately mixing an experimental Al-3Ti-0.75C alloy with Al-10Ti alloy and commercial purity aluminium. The grain refining efficiency of these grain refiners was assessed to investigate the role of the insoluble TiC and the soluble Al{sub 3}Ti particles. The optimum chemistry for the Al-Ti-C grain refiners was also identified.

Kilowatt isotope power system. Phase II plan. Volume I. Phase II program plan

International Nuclear Information System (INIS)

1978-01-01

The development of a Kilowatt Isotope Power System (KIPS) was begun in 1975 for the purpose of satisfying the power requirements of satellites in the 1980's. The KIPS is a 238 PuO 2 -fueled organic Rankine cycle turbine power system to provide a design output of 500 to 2000 W. Phase II of the overall 3-phase KIPS program is described. This volume presents a program plan for qualifying the organic Rankine power system for flight test in 1982. The program plan calls for the design and fabrication of the proposed flight power system; conducting a development and a qualification program including both environmental and endurance testing, using an electrical and a radioisotope heat source; planning for flight test and spacecraft integration; and continuing ground demonstration system testing to act as a flight system breadboard and to accumulate life data

Superconductivity Program for electric power systems: 1994 annual PEER review. Volume 1, Meeting proceedings

International Nuclear Information System (INIS)

1994-01-01

This is Volume I of information presented at the Annual Peer Review of the Superconductivity Program For Electric Power Systems. Topics include: Wire development; powder synthesis; characterization of superconducting materials; electric power applications; magnetic refrigerators; and motor cooling issues. Individual reports were processed separately for the database

National Low-Level Waste Management Program radionuclide report series. Volume 13, Curium-242

Energy Technology Data Exchange (ETDEWEB)

Adams, J.P.

1995-08-01

This report, Volume 13 of the National Low-Level Waste Management Program Radionuclide Report Series, discusses the radiological and chemical characteristics of curium-242 ({sup 242}Cm). This report also includes discussions about waste types and forms in which {sup 242}Cm can be found and {sup 242}Cm behavior in the environment and in the human body.

Substitute Energy Carriers from Refinement of Coal using HTR-Module

International Nuclear Information System (INIS)

Barnert, Heiko; Kugeler, Kurt; Will, Michael

2014-01-01

There is a revival of coal refinement in the world: a recent press article in Germany titled “The Renaissance of Coal Refinement”. It reports about a large number of conventional plans and plants for coal refinement in many countries in the world, and in particular in China. Nuclear energy can be of assistance, in particular the High Temperature Reactor-Module, because it offers all needed process energies. The status of the research, development, and demonstration, RDD, of technology is summarized, in particular of the former programs in Germany: The primary energy carriers were hard coal and lignite. The envisaged products were: Substitute Natural Gas, SNG, for the gas market, Hydrogen, H2, for a future H2-market, e.g. for airplane traffic, Liquid Fuels, as Substitute Gasoline, or as Energy Alcohol, e.g. Methanol CH3OH, in mixture with higher alcohols, for the car traffic and for home heating. (author)

Balanced program plan. Volume 10. Fusion: analysis for biomedical and environmental research

International Nuclear Information System (INIS)

Hungate, F.P.

1976-06-01

Development of the Balanced Program Plan for analysis for biomedical and environmental research was initiated in the spring of 1975. The goal was a redefinition of research efforts and priorities to meet ERDA's requirements for a program of health and environmental research to support the development and commercialization of energy technologies. As part of the Balanced Program planning effort the major ERDA-supported multidisciplinary laboratories were assigned responsibility for analyzing the research needs of each of nine energy technologies and describing a research program to meet these needs. The staff of the Division of Biomedical and Environmental Research was assigned the task of defining a research program addressed to each of five biomedical and environmental research categories (characterization, measurement and monitoring; physical and chemical processes and effects; health effects; ecological effects; and integrated assessment and socioeconomic processes and effects) applicable to all energy technologies. The first drafts of these documents were available for a work-shop in June 1975 at which the DBER staff and scientists from the laboratories developed a comprehensive set of program recommendations. Pacific Northwest Laboratory was assigned responsibility for defining research needs and a recommended research program for fusion and fission technologies. This report, Volume 10, presents the input for fusion

Panorama 2010: Refining: Adjusting to a changing business environment

International Nuclear Information System (INIS)

Silva, C.

2010-01-01

During the latter half of 2008, the sharp deterioration in the economic situation translated into a decline in world oil demand and, after a certain time lag, a collapse in refining margins. In 2009, this downtrend continued and was aggravated by the emergence of large amounts of surplus capacity. For one thing, the investment programs undertaken in recent years to cover growing demand for petroleum products cannot be discontinued in an abrupt manner. For another, the growth rate in 2009 was obviously flagging and inertia was strong, contributing to the accumulation of excess capacity. In the OECD countries, the current slump is expected to persist. In the medium term, a reorganization of the sector is anticipated, especially in Europe and in the United States: refining capacity will be scaled back and more stringent refinery emissions standards (SO 2 , CO 2 quota) and fuel specifications (sulfur content in bunker fuels) will be enforced. Projects will gravitate even more towards the regions of high-growth demand: the bulk of new capacity will be located in Asia. (author)

Refining of high-temperature uranium melt by filtration through foam-ceramic filters

International Nuclear Information System (INIS)

Antsiferov, V.N.; Porozova, S.E.; Filippov, V.B.; Shtutsa, M.G.; Il'enko, E.V.; Kolotygina, N.S.

2004-01-01

An opportunity of applying foam-ceramic filters of corundum-mullite composition has been studied in refining natural uranium melts. Uranium melting conditions were chosen depending on technical characteristics of the foam ceramic filters. When their using, a portion of nonmetallic inclusions decreases by 20-30% (as little as 2.0-3.5% ingot weight), their size is reduced and their distribution in the ingot volume is equalized, contamination of uranium by the filter material being failed to be noticed. The parameters of foam-ceramic filters are optimized for provision of stable characteristics of uranium melt filtration process [ru

Technical summary of groundwater quality protection program at Savannah River Plant. Volume 1. Site geohydrology, and solid and hazardous wastes

International Nuclear Information System (INIS)

Christensen, E.J.; Gordon, D.E.

1983-12-01

The program for protecting the quality of groundwater underlying the Savannah River Plant (SRP) is described in this technical summary report. The report is divided into two volumes. Volume I contains a discussion of the general site geohydrology and of both active and inactive sites used for disposal of solid and hazardous wastes. Volume II includes a discussion of radioactive waste disposal. Most information contained in these two volumes is current as of December 1983. The groundwater quality protection program has several elements which, taken collectively, are designed to achieve three major goals. These goals are to evaluate the impact on groundwater quality as a result of SRP operations, to restore or protect groundwater quality by taking corrective action as necessary, and to ensure disposal of waste materials in accordance with regulatory guidelines

Advanced Transportation System Studies. Technical Area 3: Alternate Propulsion Subsystems Concepts. Volume 3; Program Cost Estimates

Science.gov (United States)

Levack, Daniel J. H.

2000-01-01

The objective of this contract was to provide definition of alternate propulsion systems for both earth-to-orbit (ETO) and in-space vehicles (upper stages and space transfer vehicles). For such propulsion systems, technical data to describe performance, weight, dimensions, etc. was provided along with programmatic information such as cost, schedule, needed facilities, etc. Advanced technology and advanced development needs were determined and provided. This volume separately presents the various program cost estimates that were generated under three tasks: the F- IA Restart Task, the J-2S Restart Task, and the SSME Upper Stage Use Task. The conclusions, technical results , and the program cost estimates are described in more detail in Volume I - Executive Summary and in individual Final Task Reports.

Data refinement for true concurrency

Directory of Open Access Journals (Sweden)

Brijesh Dongol

2013-05-01

Full Text Available The majority of modern systems exhibit sophisticated concurrent behaviour, where several system components modify and observe the system state with fine-grained atomicity. Many systems (e.g., multi-core processors, real-time controllers also exhibit truly concurrent behaviour, where multiple events can occur simultaneously. This paper presents data refinement defined in terms of an interval-based framework, which includes high-level operators that capture non-deterministic expression evaluation. By modifying the type of an interval, our theory may be specialised to cover data refinement of both discrete and continuous systems. We present an interval-based encoding of forward simulation, then prove that our forward simulation rule is sound with respect to our data refinement definition. A number of rules for decomposing forward simulation proofs over both sequential and parallel composition are developed.

TFTR lithium blanket module program. Final design report. Volume VII. LBM instrumentation and Program of Experiments and Analysis

International Nuclear Information System (INIS)

Harker, Y.D.; Tsang, F.Y.; Jassby, D.L.

1983-07-01

The Program of Experiments and Analysis comprises 3 spheres of activity: (1) measurements of neutron fluence and flux spectra inside and around the LBM, and of tritium production in the LBM central zone; (2) neutronic-code modeling and analysis of the TFTR/LBM system to predict the quantities measured in (1); (3) comparisons of the predicted and measured quantities, and improvements of the code modeling and analysis and the experimental techniques, in order to resolve any discrepancy between prediction and measurement. The measurement techniques are discussed. Section 5 of this volume discusses the strategy for carrying out the measurement program, for making comparisons with the neutronics code predictions, and for resolving discrepancies

Grain Refinement of Permanent Mold Cast Copper Base Alloys

Energy Technology Data Exchange (ETDEWEB)

M.Sadayappan; J.P.Thomson; M.Elboujdaini; G.Ping Gu; M. Sahoo

2005-04-01

Grain refinement is a well established process for many cast and wrought alloys. The mechanical properties of various alloys could be enhanced by reducing the grain size. Refinement is also known to improve casting characteristics such as fluidity and hot tearing. Grain refinement of copper-base alloys is not widely used, especially in sand casting process. However, in permanent mold casting of copper alloys it is now common to use grain refinement to counteract the problem of severe hot tearing which also improves the pressure tightness of plumbing components. The mechanism of grain refinement in copper-base alloys is not well understood. The issues to be studied include the effect of minor alloy additions on the microstructure, their interaction with the grain refiner, effect of cooling rate, and loss of grain refinement (fading). In this investigation, efforts were made to explore and understand grain refinement of copper alloys, especially in permanent mold casting conditions.

Comparing Syntactic and Semantics Action Refinement

NARCIS (Netherlands)

Goltz, Ursula; Gorrieri, Roberto; Rensink, Arend

The semantic definition of action refinement on labelled configuration structures is compared with the notion of syntactic substitution, which can be used as another notion of action refinement in a process algebraic setting. The comparison is done by studying a process algebra equipped with

National low-level waste management program radionuclide report series, Volume 15: Uranium-238

International Nuclear Information System (INIS)

Adams, J.P.

1995-09-01

This report, Volume 15 of the National Low-Level Waste Management Program Radionuclide Report Series, discusses the radiological and chemical characteristics of uranium-238 ( 238 U). The purpose of the National Low-Level Waste Management Program Radionuclide Report Series is to provide information to state representatives and developers of low-level radioactive waste disposal facilities about the radiological, chemical, and physical characteristics of selected radionuclides and their behavior in the waste disposal facility environment. This report also includes discussions about waste types and forms in which 238 U can be found, and 238 U behavior in the environment and in the human body

Procurement planning in oil refining industries considering blending operations

DEFF Research Database (Denmark)

Oddsdottir, Thordis Anna; Grunow, Martin; Akkerman, Renzo

2013-01-01

This paper addresses procurement planning in oil refining, which has until now only had limited attention in the literature. We introduce a mixed integer nonlinear programming (MINLP) model and develop a novel two-stage solution approach, which aims at computational efficiency while addressing...... parameters than in previous literature. The developed approach is tested using historical data from Statoil A/S as well as through a comprehensive numerical analysis. The approach generates a feasible procurement plan within acceptable computation time, is able to quickly adjust an existing plan to take...

COBRA-SFS [Spent Fuel Storage]: A thermal-hydraulic analysis computer code: Volume 2, User's manual

International Nuclear Information System (INIS)

Rector, D.R.; Cuta, J.M.; Lombardo, N.J.; Michener, T.E.; Wheeler, C.L.

1986-11-01

COBRA-SFS (Spent Fuel Storage) is a general thermal-hydraulic analysis computer code used to predict temperatures and velocities in a wide variety of systems. The code was refined and specialized for spent fuel storage system analyses for the US Department of Energy's Commercial Spent Fuel Management Program. The finite-volume equations governing mass, momentum, and energy conservation are written for an incompressible, single-phase fluid. The flow equations model a wide range of conditions including natural circulation. The energy equations include the effects of solid and fluid conduction, natural convection, and thermal radiation. The COBRA-SFS code is structured to perform both steady-state and transient calculations; however, the transient capability has not yet been validated. This volume contains the input instructions for COBRA-SFS and an auxiliary radiation exchange factor code, RADX-1. It is intended to aid the user in becoming familiar with the capabilities and modeling conventions of the code

Steel refining possibilities in LF

Science.gov (United States)

Dumitru, M. G.; Ioana, A.; Constantin, N.; Ciobanu, F.; Pollifroni, M.

2018-01-01

This article presents the main possibilities for steel refining in Ladle Furnace (LF). These, are presented: steelmaking stages, steel refining through argon bottom stirring, online control of the bottom stirring, bottom stirring diagram during LF treatment of a heat, porous plug influence over the argon stirring, bottom stirring porous plug, analysis of porous plugs disposal on ladle bottom surface, bottom stirring simulation with ANSYS, bottom stirring simulation with Autodesk CFD.

On Syntactic and Semantic Action Refinement

NARCIS (Netherlands)

Hagiya, M.; Goltz, U.; Mitchell, J.C.; Gorrieri, R.; Rensink, Arend

1994-01-01

The semantic definition of action refinement on labelled event structures is compared with the notion of syntactic substitution, which can be used as another notion of action refinement in a process algebraic setting. This is done by studying a process algebra equipped with the ACP sequential

Noise bias in the refinement of structures derived from single particles

International Nuclear Information System (INIS)

Stewart, Alex; Grigorieff, Nikolaus

2004-01-01

One of the main goals in the determination of three-dimensional macromolecular structures from electron microscope images of individual molecules and complexes (single particles) is a sufficiently high spatial resolution, about 4 A, at which the interpretation with an atomic model becomes possible. To reach high resolution, an iterative refinement procedure using an expectation maximization algorithm is often used that leads to a more accurate alignment of the positional and orientational parameters for each particle. We show here the results of refinement algorithms that use a phase residual, a linear correlation coefficient, or a weighted correlation coefficient to align individual particles. The algorithms were applied to computer-generated data sets that contained projections from model structures, as well as noise. The algorithms show different degrees of over-fitting, especially at high resolution where the signal is weak. We demonstrate that the degree of over-fitting is reduced with a weighting scheme that depends on the signal-to-noise ratio in the data. The weighting also improves the accuracy of resolution measurement by the commonly used Fourier shell correlation. The performance of the refinement algorithms is compared to that using a maximum likelihood approach. The weighted correlation coefficient was implemented in the computer program FREALIGN

Refinement for Transition Systems with Responses

Directory of Open Access Journals (Sweden)

Marco Carbone

2012-07-01

Full Text Available Motivated by the response pattern for property specifications and applications within flexible workflow management systems, we report upon an initial study of modal and mixed transition systems in which the must transitions are interpreted as must eventually, and in which implementations can contain may behaviors that are resolved at run-time. We propose Transition Systems with Responses (TSRs as a suitable model for this study. We prove that TSRs correspond to a restricted class of mixed transition systems, which we refer to as the action-deterministic mixed transition systems. We show that TSRs allow for a natural definition of deadlocked and accepting states. We then transfer the standard definition of refinement for mixed transition systems to TSRs and prove that refinement does not preserve deadlock freedom. This leads to the proposal of safe refinements, which are those that preserve deadlock freedom. We exemplify the use of TSRs and (safe refinements on a small medication workflow.

Design of Grain Refiners for Aluminium Alloys

Science.gov (United States)

Tronche, A.; Greer, A. L.

The efficiency of a grain refiner can be quantified as the number of grains per nucleant particle in the solidified product. Even for effective refiners in aluminium, such as Al-5Ti-1B, it is known from experiments that efficiencies are very low, at best 10-3 to 102. It is of interest to explore the reasons for such low values, and to assess the prospects for increased efficiency though design of refiners. Recently it has been shown [1] that a simple recalescence-based model can make quantitative predictions of grain size as a function of refiner addition level, cooling rate and solute content. In the model, the initiation of grains is limited by the free growth from nucleant particles, the size distribution of which is very important. The present work uses this model as the basis for discussing the effect of particle size distribution on grain refiner performance. Larger particles (of TiB2 in the case of present interest) promote greater efficiency, as do narrower size distributions. It is shown that even if the size distribution could be exactly specified, compromises would have to be made to balance efficiency (defined as above) with other desirable characteristics of a refiner.

Structure refinement of commensurately modulated bismuth tungstate, Bi2WO6

International Nuclear Information System (INIS)

Rae, A.D.; Thompson, J.G.; Withers, R.L.

1991-01-01

The displacive ferroelectric Bi 2 WO 6 [M r = 697.81, a = 5.4559 (4), b = 5.4360 (4), c = 16.4298 (17) A, Z = 4, D x = 9.512 g cm -3 , MoKα, λ = 0sun7107 A, μ = 958.6 cm -1 , F(000) = 1151.73], is described at room temperature as a commensurate modulation of an idealized Fmmm parent structure derived from an I4/mmm structure. Transmission electron microscopy clearly showed that there are coherent intergrowths of two distinct modulated variants in Bi 2 WO 6 crystals. Displacive models of inherent F2mm and Bmab symmetry are substantial and coherent over a large volume. They reduce the space-group symmetry to B2ab. A further substantial displacive mode corresponds to rotation of corner-connected WO 6 octahedra about axes parallel to c and has either of two inherent symmetries, Abam or Bbam, the difference being associated with the way this mode reduces the space-group symmetry to P2 1 ab, while the existence of the Bbam mode reduces the intensity of h + l = 2n + 1 data and acts like a stacking fault. Group theoretical analysis of the problem details how the X-ray data can be classified so as to monitor the refinement. Anomalous dispersion selects the overall sign of the F2mm mode and determines the polarity. The overall signs chosen for the Bmab and Abam symmetry components of atom displacements select between equivalent origins. The overall signs of induced modes of inherent Amam, Bbab and Ccma symmetry had to be determined by comparative refinement since the assumption that calculated phases are best estimates can retain the initial overall sign choice for these modes during least-squares refinement. Correlations between the dominant modes and the induced modes allowed a meaningful choice of signs to resolve the pseudo homometry. Only the sign of the Bbab mode was capable of self-correction during refinement. (orig./BHO)

National Low-Level Waste Management Program Radionuclide Report Series, Volume 17: Plutonium-239

International Nuclear Information System (INIS)

Adams, J.P.; Carboneau, M.L.

1999-01-01

This report, Volume 17 of the National Low-Level Waste Management Program Radionuclide Report Series, discusses the radiological and chemical characteristics of plutonium-239 (Pu-239). This report also discusses waste types and forms in which Pu-239 can be found, waste and disposal information on Pu-239, and Pu-239 behavior in the environment and in the human body

National Low-Level Waste Management Program Radionuclide Report Series, Volume 17: Plutonium-239

Energy Technology Data Exchange (ETDEWEB)

J. P. Adams; M. L. Carboneau

1999-03-01

This report, Volume 17 of the National Low-Level Waste Management Program Radionuclide Report Series, discusses the radiological and chemical characteristics of plutonium-239 (Pu-239). This report also discusses waste types and forms in which Pu-239 can be found, waste and disposal information on Pu-239, and Pu-239 behavior in the environment and in the human body.

Bauxite Mining and Alumina Refining

Science.gov (United States)

Frisch, Neale; Olney, David

2014-01-01

Objective: To describe bauxite mining and alumina refining processes and to outline the relevant physical, chemical, biological, ergonomic, and psychosocial health risks. Methods: Review article. Results: The most important risks relate to noise, ergonomics, trauma, and caustic soda splashes of the skin/eyes. Other risks of note relate to fatigue, heat, and solar ultraviolet and for some operations tropical diseases, venomous/dangerous animals, and remote locations. Exposures to bauxite dust, alumina dust, and caustic mist in contemporary best-practice bauxite mining and alumina refining operations have not been demonstrated to be associated with clinically significant decrements in lung function. Exposures to bauxite dust and alumina dust at such operations are also not associated with the incidence of cancer. Conclusions: A range of occupational health risks in bauxite mining and alumina refining require the maintenance of effective control measures. PMID:24806720

Impact of operating variables on re-refining of vehicle waste oil to base-oil by acid-clay process

International Nuclear Information System (INIS)

Durrani, H.A.; Panhwar, M.I.; Kazi, R.A.

2009-01-01

A large volume of waste oil is generated each year as the number of vehicles in the country is increasing every day. This used lubricant oil constitutes a serious pollution problem. It easily be converted as a resource depending on the manners of utilization and management. This paper compares various end uses of waste oil and develops technology by which basic properties of the base oil can be regained. An experimental setup (Experimental rig) of acid-clay method was used to regain waste oil collected and number of experiments were conducted by varying different process variables. The impacts of the operating variables on the quality of re-refined oil are also discussed. The recovery of re-refined base oil was found in between 44-49%. (author)

South Korea - oil refining overview

International Nuclear Information System (INIS)

Hayes, D.

1999-01-01

Following the economic problems of the 1990s, the petroleum refining industry of South Korea underwent much involuntary restructuring in 1999 with respect to takeovers and mergers and these are discussed. The demand for petroleum has now pretty well recovered. The reasons for fluctuating prices in the 1990s, how the new structure should be cushioned against changes in the future, and the potential for South Korea to export refined petroleum, are all discussed

Adaptive Mesh Refinement in CTH

International Nuclear Information System (INIS)

Crawford, David

1999-01-01

This paper reports progress on implementing a new capability of adaptive mesh refinement into the Eulerian multimaterial shock- physics code CTH. The adaptivity is block-based with refinement and unrefinement occurring in an isotropic 2:1 manner. The code is designed to run on serial, multiprocessor and massive parallel platforms. An approximate factor of three in memory and performance improvements over comparable resolution non-adaptive calculations has-been demonstrated for a number of problems

Development of computer program for the economic evaluation of the volume reduction system for the low-level radioactive waste

International Nuclear Information System (INIS)

Yang, Jin Yeong; Lee, Kun Jai

1994-01-01

This study provides the basis for investigating the benefits of purchasing volume reduction equipment and includes the establishment of a volume reduction data base, the creation of the volume reduction cost analysis computer program PEEVR (Program of Economic Evaluation for the Volume Reduction), and a generic analysis designed to identify the major costs influencing the economics of the various equipment options. In treating the plant types and the wastes, this study considers that condensate polishing system is included or not in PWR and precoatcondensate polishing system, deep bed condensate polishing system in BWR and the 5 waste streams, i. e., compactibIe trash (COTRASH), ion exchange resin (IXRESIN), concentrate liquid (CONCLIQ), filter sludge (FSLUDGE), non compactible trash (COTRASH). This study uses the PVRR and LRR methods to create cost analysis and performs sensitivity analysis for the each cost variables and shows that future burial costs increases are the major factors in the economic evaluation

Price implications for Russia's oil refining

International Nuclear Information System (INIS)

Khartukov, Eugene M.

1998-01-01

Over the past several years, Russia's oil industry has undergone its radical transformation from a wholly state-run and generously subsidized oil distribution system toward a substantially privatized, cash-strapped, and quasi-market ''petropreneurship''. This fully applies to the industry's downstream sector. Still unlike more dynamic E and C operations, the country's refining has turned out better fenced off competitive market forces and is less capable to respond to market imperatives. Consequently, jammed between depressed product prices and persistent feedstock costs, Russian refiners were badly hit by the world oil glut - which has made a radical modernization of the obsolete refining sector clearly a must. (author)

Optimizing refiner operation with statistical modelling

Energy Technology Data Exchange (ETDEWEB)

Broderick, G [Noranda Research Centre, Pointe Claire, PQ (Canada)

1997-02-01

The impact of refining conditions on the energy efficiency of the process and on the handsheet quality of a chemi-mechanical pulp was studied as part of a series of pilot scale refining trials. Statistical models of refiner performance were constructed from these results and non-linear optimization of process conditions were conducted. Optimization results indicated that increasing the ratio of specific energy applied in the first stage led to a reduction of some 15 per cent in the total energy requirement. The strategy can also be used to obtain significant increases in pulp quality for a given energy input. 20 refs., 6 tabs.

Refining and end use study of coal liquids

International Nuclear Information System (INIS)

1998-01-01

Two direct coal liquids were evaluated by linear programming analysis to determine their value as petroleum refinery feedstock. The first liquid, DL1, was produced from bitiuminous coal using the Hydrocarbon Technologies, Inc.(HTI) two-stage hydrogenation process in Proof of Concept Run No.1, POC-1. The second liquid, DL2,was produced from sub-bituminous coal using a three-stage HTI process in Proof of Concept Run No. 2, POC-2; the third stage being a severe hydrogenation process. A linear programming (LP) model was developed which simulates a generic 150,000 barrel per day refinery in the Midwest U.S. Data from upgrading tests conducted on the coal liquids and related petroleum fractions in the pilot plant testing phase of the Refining and End Use Study was inputed into the model. The coal liquids were compared against a generic petroleum crude feedstock. under two scenarios. In the first scenario, it was assumed that the refinery capacity and product slate/volumes were fixed. The coal liquids would be used to replace a portion of the generic crude. The LP results showed that the DL1 material had essentially the same value as the generic crude. Due to its higher quality, the DL2 material had a value of approximately 0.60 $/barrel higher than the petroleum crude. In the second scenario, it was assumed that a market opportunity exists to increase production by one-third. This requires a refinery expansion. The feedstock for this scenario could be either 100% petroleum crude or a combination of petroleum crude and the direct coal liquids. Linear programming analysis showed that the capital cost of the refinery expansion was significantly less when coal liquids are utilized. In addition, the pilot plant testing showed that both of the direct coal liquids demonstrated superior catalytic cracking and naphtha reforming yields. Depending on the coal liquid flow rate, the value of the DL1 material was 2.5-4.0 $/barrel greater than the base petroleum crude, while the DL2

Grain refinement mechanism in A3003 alloy

International Nuclear Information System (INIS)

Cho, Hoon; Shin, Je-Sik; Lee, Byoung-Soo; Jo, Hyung-Ho

2009-01-01

In the present study, in order to find out an grain refinement mechanism, 0.1wt.% Al-10wt.%Ti master alloy was added into A3003 alloy melt contained in graphite crucible and in alumina crucible, and then the melt holding time at 750 deg. C was systematically changed from 1 min up to 120 min. It is interesting to note that the grain refinement and fading phenomena remarkably depend on the crucible material. The fading effect in the specimens using alumina crucible can be explained as the result of TiAl 3 phase dissolution into molten aluminium matrix. In the specimens using graphite crucible, the grain refinement was occurred gradually with increasing holding time. It was suggest that the continuous grain refinement is due to transition of refinement mechanism from TiAl 3 phase to TiC phase. It can be mentioned that the TiC formed from titanium and carbon solute in the aluminium melt, which came from the Al-10Ti alloy and the graphite crucible.

Concurrent reduction and distillation: an improved technique for the recovery and chemical refinement of the isotopes of cadmium and zinc

International Nuclear Information System (INIS)

Caudill, H.H.; McBride, L.E.; McDaniel, E.W.

1982-01-01

The Electromagnetic Isotope Separations Program of the Oak Ridge National Laboratory has been involved in the separation, chemical recovery, and refinement of the stable isotopes of cadmium and zinc since 1946. Traditionally, the chemical refinement procedures for these elements consisted of ion exchange separations using anion exchange resins followed by pH-controlled hydrogen sulfide precipitations. The procedures were quite time-consuming and made it difficult to remove trace quantities of sulfur which interferes in subsequent attempts to prepare rolled metal foils. As demands for 113 Cd and 68 Zn (a precursor for the production of the radiopharmaceutical 67 Ga) increased, it became evident that a quicker, more efficient refinement procedure was needed. Details of an improved method, which employs concurrent hydrogen reduction and distillation in the recovery and refinement of isotopically enriched zinc, are described. Modifications of the procedure suitable for the refinement of cadmium isotopes are also described. 3 figures, 1 table

Refining discordant gene trees.

Science.gov (United States)

Górecki, Pawel; Eulenstein, Oliver

2014-01-01

Evolutionary studies are complicated by discordance between gene trees and the species tree in which they evolved. Dealing with discordant trees often relies on comparison costs between gene and species trees, including the well-established Robinson-Foulds, gene duplication, and deep coalescence costs. While these costs have provided credible results for binary rooted gene trees, corresponding cost definitions for non-binary unrooted gene trees, which are frequently occurring in practice, are challenged by biological realism. We propose a natural extension of the well-established costs for comparing unrooted and non-binary gene trees with rooted binary species trees using a binary refinement model. For the duplication cost we describe an efficient algorithm that is based on a linear time reduction and also computes an optimal rooted binary refinement of the given gene tree. Finally, we show that similar reductions lead to solutions for computing the deep coalescence and the Robinson-Foulds costs. Our binary refinement of Robinson-Foulds, gene duplication, and deep coalescence costs for unrooted and non-binary gene trees together with the linear time reductions provided here for computing these costs significantly extends the range of trees that can be incorporated into approaches dealing with discordance.

Basic effects of pulp refining on fiber properties--a review.

Science.gov (United States)

Gharehkhani, Samira; Sadeghinezhad, Emad; Kazi, Salim Newaz; Yarmand, Hooman; Badarudin, Ahmad; Safaei, Mohammad Reza; Zubir, Mohd Nashrul Mohd

2015-01-22

The requirement for high quality pulps which are widely used in paper industries has increased the demand for pulp refining (beating) process. Pulp refining is a promising approach to improve the pulp quality by changing the fiber characteristics. The diversity of research on the effect of refining on fiber properties which is due to the different pulp sources, pulp consistency and refining equipment has interested us to provide a review on the studies over the last decade. In this article, the influence of pulp refining on structural properties i.e., fibrillations, fine formation, fiber length, fiber curl, crystallinity and distribution of surface chemical compositions is reviewed. The effect of pulp refining on electrokinetic properties of fiber e.g., surface and total charges of pulps is discussed. In addition, an overview of different refining theories, refiners as well as some tests for assessing the pulp refining is presented. Copyright © 2014 Elsevier Ltd. All rights reserved.

User's operating procedures. Volume 2: Scout project financial analysis program

Science.gov (United States)

Harris, C. G.; Haris, D. K.

1985-01-01

A review is presented of the user's operating procedures for the Scout Project Automatic Data system, called SPADS. SPADS is the result of the past seven years of software development on a Prime mini-computer located at the Scout Project Office, NASA Langley Research Center, Hampton, Virginia. SPADS was developed as a single entry, multiple cross-reference data management and information retrieval system for the automation of Project office tasks, including engineering, financial, managerial, and clerical support. This volume, two (2) of three (3), provides the instructions to operate the Scout Project Financial Analysis program in data retrieval and file maintenance via the user friendly menu drivers.

Highly Efficient Training, Refinement, and Validation of a Knowledge-based Planning Quality-Control System for Radiation Therapy Clinical Trials

Energy Technology Data Exchange (ETDEWEB)

Li, Nan; Carmona, Ruben [Department of Radiation Medicine and Applied Sciences, University of California San Diego, La Jolla, California (United States); Sirak, Igor; Kasaova, Linda [Department of Oncology and Radiotherapy, University Hospital, Hradec Kralove (Czech Republic); Followill, David [Department of Radiation Physics, University of Texas MD Anderson Cancer Center, Houston, Texas (United States); Michalski, Jeff; Bosch, Walter; Straube, William [Department of Radiation Oncology, Washington University in St Louis, St Louis, Missouri (United States); Mell, Loren K. [Department of Radiation Medicine and Applied Sciences, University of California San Diego, La Jolla, California (United States); Moore, Kevin L., E-mail: kevinmoore@ucsd.edu [Department of Radiation Medicine and Applied Sciences, University of California San Diego, La Jolla, California (United States)

2017-01-01

Purpose: To demonstrate an efficient method for training and validation of a knowledge-based planning (KBP) system as a radiation therapy clinical trial plan quality-control system. Methods and Materials: We analyzed 86 patients with stage IB through IVA cervical cancer treated with intensity modulated radiation therapy at 2 institutions according to the standards of the INTERTECC (International Evaluation of Radiotherapy Technology Effectiveness in Cervical Cancer, National Clinical Trials Network identifier: 01554397) protocol. The protocol used a planning target volume and 2 primary organs at risk: pelvic bone marrow (PBM) and bowel. Secondary organs at risk were rectum and bladder. Initial unfiltered dose-volume histogram (DVH) estimation models were trained using all 86 plans. Refined training sets were created by removing sub-optimal plans from the unfiltered sample, and DVH estimation models… and DVH estimation models were constructed by identifying 30 of 86 plans emphasizing PBM sparing (comparing protocol-specified dosimetric cutpoints V{sub 10} (percentage volume of PBM receiving at least 10 Gy dose) and V{sub 20} (percentage volume of PBM receiving at least 20 Gy dose) with unfiltered predictions) and another 30 of 86 plans emphasizing bowel sparing (comparing V{sub 40} (absolute volume of bowel receiving at least 40 Gy dose) and V{sub 45} (absolute volume of bowel receiving at least 45 Gy dose), 9 in common with the PBM set). To obtain deliverable KBP plans, refined models must inform patient-specific optimization objectives and/or priorities (an auto-planning “routine”). Four candidate routines emphasizing different tradeoffs were composed, and a script was developed to automatically re-plan multiple patients with each routine. After selection of the routine that best met protocol objectives in the 51-patient training sample (KBP{sub FINAL}), protocol-specific DVH metrics and normal tissue complication probability were compared for original

National Aeronautics and Space Administration (NASA)/American Society for Engineering Education (ASEE) Summer Faculty Fellowship Program, 1998. Volume 1

Science.gov (United States)

Bannerot, Richard B. (Editor); Sickorez, Donn G. (Editor)

1999-01-01

JSC NASA/ASEE Summer Faculty Fellowship Program was conducted by the University of Houston and JSC, under ASEE. The objectives of the program are to further the professional knowledge of qualified engineering and science members; stimulate an exchange of ideas between participants and NASA; enrich and refresh the research and teaching activities of participants; and contribute to the research objectives of the NASA Centers. Each faculty fellow spent at least 10 weeks at JSC engaged in a research project commensurate with his/her interests and background and worked in collaboration with a NASA/JSC colleague. This document is a compilation of the final reports on the fellows' research projects performed during the summer of 1998. Volume 1, current volume, contains the first reports, and volume 2 contains the remaining reports.

Subseabed disposal program annual report, January-December 1979. Volume II. Appendices (principal investigator progress reports). Part 1 of 2

International Nuclear Information System (INIS)

Talbert, D.M.

1981-04-01

Volume II of the sixth annual report describing the progress and evaluating the status of the Subseabed Disposal Program contains the appendices referred to in Volume I, Summary and Status. Because of the length of Volume II, it has been split into two parts for publication purposes. Part 1 contains Appendices A-O; Part 2 contains Appendices P-FF. Separate abstracts have been prepared of each Appendix for inclusion in the Energy Data Base

Subseabed disposal program annual report, January-December 1979. Volume II. Appendices (principal investigator progress reports). Part 2 of 2

International Nuclear Information System (INIS)

Talbert, D.M.

1981-04-01

Volume II of the sixth annual report describing the progress and evaluating the status of the Subseabed Disposal Program contains the appendices referred to in Volume II, Summary and Status. Because of the length of Volume II, it has been split into two parts for publication purposes. Part 1 contains Appendices A-O; Part 2 contains Appendices P-FF. Separate abstracts have been prepared for each appendix for inclusion in the Energy Data Base

Interactive visual exploration and refinement of cluster assignments.

Science.gov (United States)

Kern, Michael; Lex, Alexander; Gehlenborg, Nils; Johnson, Chris R

2017-09-12

With ever-increasing amounts of data produced in biology research, scientists are in need of efficient data analysis methods. Cluster analysis, combined with visualization of the results, is one such method that can be used to make sense of large data volumes. At the same time, cluster analysis is known to be imperfect and depends on the choice of algorithms, parameters, and distance measures. Most clustering algorithms don't properly account for ambiguity in the source data, as records are often assigned to discrete clusters, even if an assignment is unclear. While there are metrics and visualization techniques that allow analysts to compare clusterings or to judge cluster quality, there is no comprehensive method that allows analysts to evaluate, compare, and refine cluster assignments based on the source data, derived scores, and contextual data. In this paper, we introduce a method that explicitly visualizes the quality of cluster assignments, allows comparisons of clustering results and enables analysts to manually curate and refine cluster assignments. Our methods are applicable to matrix data clustered with partitional, hierarchical, and fuzzy clustering algorithms. Furthermore, we enable analysts to explore clustering results in context of other data, for example, to observe whether a clustering of genomic data results in a meaningful differentiation in phenotypes. Our methods are integrated into Caleydo StratomeX, a popular, web-based, disease subtype analysis tool. We show in a usage scenario that our approach can reveal ambiguities in cluster assignments and produce improved clusterings that better differentiate genotypes and phenotypes.

Oil refining expansion criteria for Brazil

International Nuclear Information System (INIS)

Tavares, M.E.E.; Szklo, A.S.; Machado, G.V.; Schaeffer, R.; Mariano, J.B.; Sala, J.F.

2006-01-01

This paper assesses different strategies for the expansion of Brazil's oil refining segment, using criteria that range from energy security (reducing imports and vulnerability for key products) through to maximizing the profitability of this sector (boosting the output of higher value oil products) and adding value to Brazil's oil production (reducing exports of heavy acid oil). The development prospects are analyzed for conventional fuel production technology routes, sketching out three possible refining schemes for Brazilian oil and a GTL plant for producing gasoil from natural gas. Market scenario simulations indicate that investments will be required in Brazil's oil refining segment over and above those allocated to planned modifications in its current facilities, reducing the nation's vulnerability in terms of gasoil and petrochemical naphtha imports. Although not economically attractive, oil refining is a key activity that is crucial to oil company strategies. The decision to invest in this segment depends on local infrastructure conditions, environmental constraints and fuel specifications, in addition to oil company strategies, steady growth in demand and the definition of a government policy that eases institutional risks. (author)

Oil refining expansion criteria for Brazil

International Nuclear Information System (INIS)

Tavares, Marina Elisabete Espinho; Szklo, Alexandre Salem; Machado, Giovani Vitoria; Schaeffer, Roberto; Mariano, Jacqueline Barboza; Sala, Janaina Francisco

2006-01-01

This paper assesses different strategies for the expansion of Brazil's oil refining segment, using criteria that range from energy security (reducing imports and vulnerability for key products) through to maximizing the profitability of this sector (boosting the output of higher value oil products) and adding value to Brazil's oil production (reducing exports of heavy acid oil). The development prospects are analyzed for conventional fuel production technology routes, sketching out three possible refining schemes for Brazilian oil and a GTL plant for producing gasoil from natural gas. Market scenario simulations indicate that investments will be required in Brazil's oil refining segment over and above those allocated to planned modifications in its current facilities, reducing the nation's vulnerability in terms of gasoil and petrochemical naphtha imports. Although not economically attractive, oil refining is a key activity that is crucial to oil company strategies. The decision to invest in this segment depends on local infrastructure conditions, environmental constraints and fuel specifications, in addition to oil company strategies, steady growth in demand and the definition of a government policy that eases institutional risks

Short-term moderate intensive high volume training program provides aerobic endurance benefit in wheelchair basketball players.

Science.gov (United States)

Skucas, Kestutis; Pokvytyte, Vaida

2017-04-01

The aim of this paper was to investigate the effect of short-term period, moderate intensity and high volume endurance training on physiological variables in elite wheelchair basketball players. Eight wheelchair basketball players were examined. The subjects participated in a two-week intervention program of mainly two training types: wheelchair basketball and wheelchair driving endurance training. The subjects performed the continuously increasing cycling exercise (CCE) at the constant 60 rpm arm cranking speed at the beginning of the program and after two weeks of the program. The initial workload was 20 W, then the workload was increased by 2 W every 5 seconds until fatigue. The post training of the wheelchair basketball group in the study showed a significant improvement in the peak oxygen uptake (VO2peak) and the peak power output (POpeak). VO2peak increased by 9% from 2.32±0.16 L/min to 2.53±0.2 L/min (Pbasketball squad had relatively high levels of aerobic fitness prior to participating in the endurance training program. Nevertheless, the high-volume, moderate-intensity, short-term training program, which evolved over the two-weeks period, resulted in the improvement of the athlete's aerobic endurance. The ventilatory threshold (VT) and the second ventilatory threshold (VT2) are good markers for aerobic capacity of wheelchair athletes.

Hybrid-hybrid matrix structural refinement of a DNA three-way junction from 3D NOESY-NOESY

International Nuclear Information System (INIS)

Thiviyanathan, Varatharasa; Luxon, Bruce A.; Leontis, Neocles B.; Illangasekare, Nishantha; Donne, David G.; Gorenstein, David G.

1999-01-01

Homonuclear 3D NOESY-NOESY has shown great promise for the structural refinement of large biomolecules. A computationally efficient hybrid-hybrid relaxation matrix refinement methodology, using 3D NOESY-NOESY data, was used to refine the structure of a DNA three-way junction having two unpaired bases at the branch point of the junction. The NMR data and the relaxation matrix refinement confirm that the DNA three-way junction exists in a folded conformation with two of the helical stems stacked upon each other. The third unstacked stem extends away from the junction, forming an acute angle (∼60 deg.) with the stacked stems. The two unpaired bases are stacked upon each other and are exposed to the solvent. Helical parameters for the bases in all three strands show slight deviations from typical values expected for right-handed B-form DNA. Inter-nucleotide imino-imino NOEs between the bases at the branch point of the junction show that the junction region is well defined. The helical stems show mobility (± 20 deg.) indicating dynamic processes around the junction region. The unstacked helical stem adjacent to the unpaired bases shows greater mobility compared to the other two stems. The results from this study indicate that the 3D hybrid-hybrid matrix MORASS refinement methodology, by combining the spectral dispersion of 3D NOESY-NOESY and the computational efficiency of 2D refinement programs, provides an accurate and robust means for structure determination of large biomolecules. Our results also indicate that the 3D MORASS method gives higher quality structures compared to the 2D complete relaxation matrix refinement method

Refined large N duality for knots

DEFF Research Database (Denmark)

Kameyama, Masaya; Nawata, Satoshi

We formulate large N duality of U(N) refined Chern-Simons theory with a torus knot/link in S³. By studying refined BPS states in M-theory, we provide the explicit form of low-energy effective actions of Type IIA string theory with D4-branes on the Ω-background. This form enables us to relate...

Region-of-interest volumetric visual hull refinement

KAUST Repository

Knoblauch, Daniel; Kuester, Falko

2010-01-01

This paper introduces a region-of-interest visual hull refinement technique, based on flexible voxel grids for volumetric visual hull reconstructions. Region-of-interest refinement is based on a multipass process, beginning with a focussed visual

Mod-5A wind turbine generator program design report. Volume 3: Final design and system description, book 2

Science.gov (United States)

1984-01-01

The design, development and analysis of the 7.3MW MOD-5A wind turbine generator is documented. The report is divided into four volumes: Volume 1 summarizes the entire MOD-5A program, Volume 2 discusses the conceptual and preliminary design phases, Volume 3 describes the final design of the MOD-5A, and Volume 4 contains the drawings and specifications developed for the final design. Volume 3, book 2 describes the performance and characteristics of the MOD-5A wind turbine generator in its final configuration. The subsystem for power generation, control, and instrumentation subsystems is described in detail. The manufacturing and construction plans, and the preparation of a potential site on Oahu, Hawaii, are documented. The quality assurance and safety plan, and analyses of failure modes and effects, and reliability, availability and maintainability are presented.

US refining reviewed

International Nuclear Information System (INIS)

Yamaguchi, N.D.

1998-01-01

The paper reviews the history, present position and future prospects of the petroleum industry in the USA. The main focus is on supply and demand, the high quality of the products, refinery capacity and product trade balances. Diagrams show historical trends in output, product demand, demand for transport fuels and oil, refinery capacity, refinery closures, and imports and exports. Some particularly salient points brought out were (i) production of US crude shows a marked downward trend but imports of crude will continue to increase, (ii) product demand will continue to grow even though the levels are already high, (iii) the demand is dominated by those products that typically yield the highest income for the refiner, (i.e. high quality transport fuels for environmental compliance), (iv) refinery capacity has decreased since 1980 and (v) refining will continue to have financial problems but will still be profitable. (UK)

Neutrosophic Refined Similarity Measure Based on Cosine Function

Directory of Open Access Journals (Sweden)

Said Broumi

2014-12-01

Full Text Available In this paper, the cosine similarity measure of neutrosophic refined (multi- sets is proposed and its properties are studied. The concept of this cosine similarity measure of neutrosophic refined sets is the extension of improved cosine similarity measure of single valued neutrosophic. Finally, using this cosine similarity measure of neutrosophic refined set, the application of medical diagnosis is presented.

Future of French refining

International Nuclear Information System (INIS)

Calvet, B.

1993-01-01

Over recent years, the refining industry has had to grapple with a growing burden of environmental and safety regulations concerning not only its plants and other facilities, but also its end products. At the same time, it has had to bear the effects of the reduction of the special status that used to apply to petroleum, and the consequences of economic freedom, to which we should add, as specifically concerns the French market, the impact of energy policy and the pro-nuclear option. The result is a drop in heavy fuel oil from 36 million tonnes per year in 1973 to 6.3 million in 1992, and in home-heating fuel from 37 to 18 million per year. This fast-moving market is highly competitive. The French market in particular is wide open to imports, but the refining companies are still heavy exporters for those products with high added-value, like lubricants, jet fuel, and lead-free gasolines. The competition has led the refining companies to commit themselves to quality, and to publicize their efforts in this direction. This is why the long-term perspectives for petroleum fuels are still wide open. This is supported by the probable expectation that the goal of economic efficiency is likely to soften the effects of the energy policy, which penalizes petroleum products, in that they have now become competitive again. In the European context, with the challenge of environmental protection and the decline in heavy fuel outlets, French refining has to keep on improving the quality of its products and plants, which means major investments. The industry absolutely must return to a more normal level of profitability, in order to sustain this financial effort, and generate the prosperity of its high-performance plants and equipment. 1 fig., 5 tabs

The evolution of oil refining in Europe

Energy Technology Data Exchange (ETDEWEB)

Reid, A. [CONCAWE, Brussels (Belgium)

2013-04-01

Back in 1963 when CONCAWE was founded, the world looked very different from what it is today, and so did the global and European refining industry. Oil product markets were expanding fast and new refineries were being built at a steady rate. The oil crisis of the 1970s brought an abrupt end to this, heralding a long era of consolidation and stepwise adaptation. At the same time the nature of the global oil business shifted from fully integrated companies producing, transporting and refining their own oil to a much more diversified situation where oil production ('upstream') and refining/distribution ('downstream') gradually became two essentially separate businesses. From being purely a 'cost centre' in an integrated chain, refining has become a separate activity in its own right, operating as a 'profit centre' between two global markets - crude oil and products - which, although not entirely independent, have their own dynamics and influences. In addition demand gradually shifted towards lighter products while the quality requirements on all products were considerably tightened. This article explores the new challenges that these changes have imposed on EU refiners, and describes CONCAWE's contributions to understanding their impact on refinery production and investments.

40 CFR 80.217 - How does a refiner or importer apply for the GPA standards?

Science.gov (United States)

2010-07-01

... annual average sulfur standard for gasoline produced for use in the GPA for the 2004 through 2006 annual... for gasoline produced for use in the GPA. (d) If EPA finds that a refiner or importer provided false... (CONTINUED) AIR PROGRAMS (CONTINUED) REGULATION OF FUELS AND FUEL ADDITIVES Gasoline Sulfur Geographic Phase...

Energy Extension Service Pilot Program: evaluation report after two years. Volume II. State reports

Energy Technology Data Exchange (ETDEWEB)

None

1980-04-01

This report, Vol. II, presents a discussion of the operations of the ten EES pilot state programs during the period from October 1, 1977 through September 30, 1979. Each of the ten pilot states - Alabama, Connecticut, Michigan, New Mexico, Pennsylvania, Tennessee, Texas, Washington, Wisconsin, and Wyoming - received a grant of approximately $1.1 million to develop and implement an 18-month program beginning on October 1, 1977. In September 1978, each State received an additional $370,000 for service-delivery programs for the extension of the pilot program, April 1979 through September 1979. A case-study description of the operations of the pilot program in each State is provided here, with special attention given to the two programs selected in each State for more-detailed study and survey research. Although the thrust of this volume is descriptive, some survey data and analyses are presented for the emphasis programs. Two telephone surveys of clients and a non-client sample were conducted, one at the end of the first year of the pilot program (October 1977 - September 1978) and one at the end of the second year (October 1978 - September 1979).

U.S. petroleum refining: Meeting requirements for cleaner fuels and refineries

International Nuclear Information System (INIS)

Warden, R.B.

1993-01-01

A review is presented of a study carried out by the National Petroleum Council that assessed the ability of the U.S. oil industry to manufacture and supply the quantity and quality of products required in the 1990s and beyond. The competitiveness of domestic supply vs product imports was analyzed and the investment requirements and other costs associated with meeting new environmental legislation and regulations on petroleum products and refineries were addressed. In particular, the requirements of the 1990 Clean Air Act Amendments and other environmental, health, and safety initiatives, both current and prospective, were evaluated. Refineries and the logistics system were studied but not crude oil supply or service stations. The costs of stationary source health, safety and environmental regulations and requirements were evaluated for the years 1995, 2000 and 2010, and sources of U.S. light products and U.S. refinery utilization were modelled for these years. Three demand scenarios were considered: growth, no-growth, and decline. Annual expenditures for health, safety and environment programs inside refineries are expected to double in the 1990s. Expenditures of $106 billion are projected over the period 1990-2010 for new facilities and programs necessary for current and anticipated stationary source regulations. Refining and logistics costs will increase substantially. Other conclusions related to capital expenditures, refining capability, product compatibility, oxygenates and foreign product supply cost are drawn. 26 figs

A spatially adaptive grid-refinement approach for the finite element solution of the even-parity Boltzmann transport equation

International Nuclear Information System (INIS)

Mirza, Anwar M.; Iqbal, Shaukat; Rahman, Faizur

2007-01-01

A spatially adaptive grid-refinement approach has been investigated to solve the even-parity Boltzmann transport equation. A residual based a posteriori error estimation scheme has been utilized for checking the approximate solutions for various finite element grids. The local particle balance has been considered as an error assessment criterion. To implement the adaptive approach, a computer program ADAFENT (adaptive finite elements for neutron transport) has been developed to solve the second order even-parity Boltzmann transport equation using K + variational principle for slab geometry. The program has a core K + module which employs Lagrange polynomials as spatial basis functions for the finite element formulation and Legendre polynomials for the directional dependence of the solution. The core module is called in by the adaptive grid generator to determine local gradients and residuals to explore the possibility of grid refinements in appropriate regions of the problem. The a posteriori error estimation scheme has been implemented in the outer grid refining iteration module. Numerical experiments indicate that local errors are large in regions where the flux gradients are large. A comparison of the spatially adaptive grid-refinement approach with that of uniform meshing approach for various benchmark cases confirms its superiority in greatly enhancing the accuracy of the solution without increasing the number of unknown coefficients. A reduction in the local errors of the order of 10 2 has been achieved using the new approach in some cases

A spatially adaptive grid-refinement approach for the finite element solution of the even-parity Boltzmann transport equation

Energy Technology Data Exchange (ETDEWEB)

Mirza, Anwar M. [Department of Computer Science, National University of Computer and Emerging Sciences, NUCES-FAST, A.K. Brohi Road, H-11, Islamabad (Pakistan)], E-mail: anwar.m.mirza@gmail.com; Iqbal, Shaukat [Faculty of Computer Science and Engineering, Ghulam Ishaq Khan (GIK) Institute of Engineering Science and Technology, Topi-23460, Swabi (Pakistan)], E-mail: shaukat@giki.edu.pk; Rahman, Faizur [Department of Physics, Allama Iqbal Open University, H-8 Islamabad (Pakistan)

2007-07-15

A spatially adaptive grid-refinement approach has been investigated to solve the even-parity Boltzmann transport equation. A residual based a posteriori error estimation scheme has been utilized for checking the approximate solutions for various finite element grids. The local particle balance has been considered as an error assessment criterion. To implement the adaptive approach, a computer program ADAFENT (adaptive finite elements for neutron transport) has been developed to solve the second order even-parity Boltzmann transport equation using K{sup +} variational principle for slab geometry. The program has a core K{sup +} module which employs Lagrange polynomials as spatial basis functions for the finite element formulation and Legendre polynomials for the directional dependence of the solution. The core module is called in by the adaptive grid generator to determine local gradients and residuals to explore the possibility of grid refinements in appropriate regions of the problem. The a posteriori error estimation scheme has been implemented in the outer grid refining iteration module. Numerical experiments indicate that local errors are large in regions where the flux gradients are large. A comparison of the spatially adaptive grid-refinement approach with that of uniform meshing approach for various benchmark cases confirms its superiority in greatly enhancing the accuracy of the solution without increasing the number of unknown coefficients. A reduction in the local errors of the order of 10{sup 2} has been achieved using the new approach in some cases.

Refining's-clean new jingle

International Nuclear Information System (INIS)

Anon.

1992-01-01

This paper reports that at a time when profit margins are slim and gasoline demand is down, the U.S. petroleum-refining industry is facing one of its greatest challenges; How to meet new federal and state laws for reformulated gasoline, oxygenated fuels, low-sulfur diesel and other measures to improve the environment. The American Petroleum Institute (API) estimates that industry will spend between $15 and $23 billion by the end of the decade to meet the U.S. Clean Air Act Amendments (CAAA) of 1990, and other legislation. ENSR Consulting and Engineering's capital-spending figure runs to between $70 and 100 billion this decade, including $24 billion to produce reformulated fuels and $10-12 billion to reduce refinery emissions. M.W. Kellogg Co. estimates that refiners may have to spend up to $30 billion this decade to meet the demand for reformulated gasoline. The estimates are wide-ranging because refiners are still studying their options and delaying final decisions as long as they can, to try to ensure they are the best and least-costly decisions. Oxygenated fuels will be required next winter, but federal regulations for reformulated gasoline won't go into effect until 1995, while California's tougher reformulated-fuels law will kick in the following year

Sustainable design guidelines to support the Washington State ferries terminal design manual : design guideline application and refinement.

Science.gov (United States)

2013-08-01

The Sustainable Design Guidelines were developed in Phase I of this research program (WA-RD : 816.1). Here we are reporting on the Phase II effort that beta-tested the Phase I Guidelines on : example ferry terminal designs and refinements made ...

Refining of crude uranium by solvent extraction for production of nuclear pure uranium metal

International Nuclear Information System (INIS)

Gupta, S.K.; Manna, S.; Singha, M.; Hareendran, K.N.; Chowdhury, S.; Satpati, S.K.; Kumar, K.

2007-01-01

Uranium is the primary fuel material for any nuclear fission energy program. Natural uranium contains only 0.712% of 235 U as fissile constituent. This low concentration of fissile isotope in natural uranium calls for a very high level of purity, especially with respect to neutron poisons like B, Cd, Gd etc. before it can be used as nuclear fuel. Solvent extraction is a widely used technique by which crude uranium is purified for reactor use. Uranium metal plant (UMP), BARC, Trombay is engaged in refining of uranium concentrate for production of nuclear pure uranium metal for fabrication of fuel for research reactors. This paper reviews some of the fundamental aspects of this refining process with some special references to UMP, BARC. (author)

Finite Volume Based Computer Program for Ground Source Heat Pump System

Energy Technology Data Exchange (ETDEWEB)

Menart, James A. [Wright State University

2013-02-22

This report is a compilation of the work that has been done on the grant DE-EE0002805 entitled ?Finite Volume Based Computer Program for Ground Source Heat Pump Systems.? The goal of this project was to develop a detailed computer simulation tool for GSHP (ground source heat pump) heating and cooling systems. Two such tools were developed as part of this DOE (Department of Energy) grant; the first is a two-dimensional computer program called GEO2D and the second is a three-dimensional computer program called GEO3D. Both of these simulation tools provide an extensive array of results to the user. A unique aspect of both these simulation tools is the complete temperature profile information calculated and presented. Complete temperature profiles throughout the ground, casing, tube wall, and fluid are provided as a function of time. The fluid temperatures from and to the heat pump, as a function of time, are also provided. In addition to temperature information, detailed heat rate information at several locations as a function of time is determined. Heat rates between the heat pump and the building indoor environment, between the working fluid and the heat pump, and between the working fluid and the ground are computed. The heat rates between the ground and the working fluid are calculated as a function time and position along the ground loop. The heating and cooling loads of the building being fitted with a GSHP are determined with the computer program developed by DOE called ENERGYPLUS. Lastly COP (coefficient of performance) results as a function of time are provided. Both the two-dimensional and three-dimensional computer programs developed as part of this work are based upon a detailed finite volume solution of the energy equation for the ground and ground loop. Real heat pump characteristics are entered into the program and used to model the heat pump performance. Thus these computer tools simulate the coupled performance of the ground loop and the heat pump

The National Shipbuilding Research Program 1985 Ship Production Symposium Volume 2 Paper No. 22: Expanded Planning Yard Concept and Configuration Accounting or Improving Navy Ship Engineering

National Research Council Canada - National Science Library

1985-01-01

.... Requirements for ship acquisition programs have been refined to reflect these improvements. We have learned that there is a need for clearly assigned responsibility in engineering, that configuration identification must be an integral part of engineering, and that logistics support must be an integral part of engineering.

Transpiration and film cooling boundary layer computer program. Volume 1: Numerical solutions of the turbulent boundary layer equations with equilibrium chemistry

Science.gov (United States)

Levine, J. N.

1971-01-01

A finite difference turbulent boundary layer computer program has been developed. The program is primarily oriented towards the calculation of boundary layer performance losses in rocket engines; however, the solution is general, and has much broader applicability. The effects of transpiration and film cooling as well as the effect of equilibrium chemical reactions (currently restricted to the H2-O2 system) can be calculated. The turbulent transport terms are evaluated using the phenomenological mixing length - eddy viscosity concept. The equations of motion are solved using the Crank-Nicolson implicit finite difference technique. The analysis and computer program have been checked out by solving a series of both laminar and turbulent test cases and comparing the results to data or other solutions. These comparisons have shown that the program is capable of producing very satisfactory results for a wide range of flows. Further refinements to the analysis and program, especially as applied to film cooling solutions, would be aided by the acquisition of a firm data base.

Refinement of the concept of uncertainty.

Science.gov (United States)

Penrod, J

2001-04-01

To analyse the conceptual maturity of uncertainty; to develop an expanded theoretical definition of uncertainty; to advance the concept using methods of concept refinement; and to analyse congruency with the conceptualization of uncertainty presented in the theory of hope, enduring, and suffering. Uncertainty is of concern in nursing as people experience complex life events surrounding health. In an earlier nursing study that linked the concepts of hope, enduring, and suffering into a single theoretical scheme, a state best described as 'uncertainty' arose. This study was undertaken to explore how this conceptualization fit with the scientific literature on uncertainty and to refine the concept. Initially, a concept analysis using advanced methods described by Morse, Hupcey, Mitcham and colleagues was completed. The concept was determined to be partially mature. A theoretical definition was derived and techniques of concept refinement using the literature as data were applied. The refined concept was found to be congruent with the concept of uncertainty that had emerged in the model of hope, enduring and suffering. Further investigation is needed to explore the extent of probabilistic reasoning and the effects of confidence and control on feelings of uncertainty and certainty.

Refinement Checking on Parametric Modal Transition Systems

DEFF Research Database (Denmark)

Benes, Nikola; Kretínsky, Jan; Larsen, Kim Guldstrand

2015-01-01

Modal transition systems (MTS) is a well-studied specification formalism of reactive systems supporting a step-wise refinement methodology. Despite its many advantages, the formalism as well as its currently known extensions are incapable of expressing some practically needed aspects in the refin...

Hydroprocessing and premium II refinery: a new refining philosophy for an era of clean fuels

Energy Technology Data Exchange (ETDEWEB)

Delgaudio, Caio Veiga Penna; Pinotti, Rafael [Petroleo Brasileiro S.A. (PETROBRAS), Rio de Janeiro, RJ (Brazil)

2012-07-01

This paper discusses a brief history of Brazilian's emission and fuel specifications, since the appearance of PROCONVE until the late stages of the program for vehicles powered by gasoline and diesel. The development of the Brazilian refining is analyzed taking into account the emission and specification evolutions, and it can be perceived that the system's complexity increases while new constraints are imposed by the regulator. This aspect is even more apparent when the detailed scheme of the Premium II refinery and its main unit, the catalytic hydrocracker (HCC, which has not yet been part of PETROBRAS' refining park and will appear in three of the four new refineries of the company) is described. The new projects represent the culmination of the intensive use of energy and raw material for obtaining the products with the new specifications. There is a price for this development, both in investments and increased operating costs due to greater complexity of the system. To adapt to the era of clean fuels, refiners will present a series of challenges that will lead them to seek for more efficient processes and operational excellence (and ongoing efforts to reduce their emissions) in order to ensure positive refining margins. (author)

Japan's refiner/marketers headed for major shakeout

International Nuclear Information System (INIS)

Anon.

1996-01-01

Japan's downstream oil industry is in a state of crisis and headed for a major shakeout. The major catalyst for this was a dramatic deregulation step during April 1996 that allowed refined petroleum product imports by non-refiners. The move, together with a sharp drop in refining margins, falling retail gasoline prices, and a service station sector on the brink of collapse, are all leading to massive changes in the way the country's refiners and marketers do business. This paper reviews the collapse of corporate profits during this period of deregulation; the development of a new price system geared toward bringing the prices of gasoline, fuel oil, and kerosene into line with each other to offset the fall in gasoline prices; and industry restructuring including mergers, acquisitions, and marketing consolidation. The paper then makes predictions on the outcome of these changes on the Japanese oil industry

Minerals Yearbook, volume III, Area Reports—International—Europe and Central Eurasia

Science.gov (United States)

Geological Survey, U.S.

2018-01-01

The U.S. Geological Survey (USGS) Minerals Yearbook discusses the performance of the worldwide minerals and materials industries and provides background information to assist in interpreting that performance. Content of the individual Minerals Yearbook volumes follows:Volume I, Metals and Minerals, contains chapters about virtually all metallic and industrial mineral commodities important to the U.S. economy. Chapters on survey methods, summary statistics for domestic nonfuel minerals, and trends in mining and quarrying in the metals and industrial mineral industries in the United States are also included.Volume II, Area Reports: Domestic, contains a chapter on the mineral industry of each of the 50 States and Puerto Rico and the Administered Islands. This volume also has chapters on survey methods and summary statistics of domestic nonfuel minerals.Volume III, Area Reports: International, is published as four separate reports. These regional reports contain the latest available minerals data on more than 180 foreign countries and discuss the importance of minerals to the economies of these nations and the United States. Each report begins with an overview of the region’s mineral industries during the year. It continues with individual country chapters that examine the mining, refining, processing, and use of minerals in each country of the region and how each country’s mineral industry relates to U.S. industry. Most chapters include production tables and industry structure tables, information about Government policies and programs that affect the country’s mineral industry, and an outlook section.The USGS continually strives to improve the value of its publications to users. Constructive comments and suggestions by readers of the Minerals Yearbook are welcomed.

Minerals Yearbook, volume III, Area Reports—International—Asia and the Pacific

Science.gov (United States)

Geological Survey, U.S.

2018-01-01

The U.S. Geological Survey (USGS) Minerals Yearbook discusses the performance of the worldwide minerals and materials industries and provides background information to assist in interpreting that performance. Content of the individual Minerals Yearbook volumes follows:Volume I, Metals and Minerals, contains chapters about virtually all metallic and industrial mineral commodities important to the U.S. economy. Chapters on survey methods, summary statistics for domestic nonfuel minerals, and trends in mining and quarrying in the metals and industrial mineral industries in the United States are also included.Volume II, Area Reports: Domestic, contains a chapter on the mineral industry of each of the 50 States and Puerto Rico and the Administered Islands. This volume also has chapters on survey methods and summary statistics of domestic nonfuel minerals.Volume III, Area Reports: International, is published as four separate reports. These regional reports contain the latest available minerals data on more than 180 foreign countries and discuss the importance of minerals to the economies of these nations and the United States. Each report begins with an overview of the region’s mineral industries during the year. It continues with individual country chapters that examine the mining, refining, processing, and use of minerals in each country of the region and how each country’s mineral industry relates to U.S. industry. Most chapters include production tables and industry structure tables, information about Government policies and programs that affect the country’s mineral industry, and an outlook section.The USGS continually strives to improve the value of its publications to users. Constructive comments and suggestions by readers of the Minerals Yearbook are welcomed.

Minerals Yearbook, volume III, Area Reports—International—Latin America and Canada

Science.gov (United States)

,

2018-01-01

The U.S. Geological Survey (USGS) Minerals Yearbook discusses the performance of the worldwide minerals and materials industries and provides background information to assist in interpreting that performance. Content of the individual Minerals Yearbook volumes follows:Volume I, Metals and Minerals, contains chapters about virtually all metallic and industrial mineral commodities important to the U.S. economy. Chapters on survey methods, summary statistics for domestic nonfuel minerals, and trends in mining and quarrying in the metals and industrial mineral industries in the United States are also included.Volume II, Area Reports: Domestic, contains a chapter on the mineral industry of each of the 50 States and Puerto Rico and the Administered Islands. This volume also has chapters on survey methods and summary statistics of domestic nonfuel minerals.Volume III, Area Reports: International, is published as four separate reports. These regional reports contain the latest available minerals data on more than 180 foreign countries and discuss the importance of minerals to the economies of these nations and the United States. Each report begins with an overview of the region’s mineral industries during the year. It continues with individual country chapters that examine the mining, refining, processing, and use of minerals in each country of the region and how each country’s mineral industry relates to U.S. industry. Most chapters include production tables and industry structure tables, information about Government policies and programs that affect the country’s mineral industry, and an outlook section.The USGS continually strives to improve the value of its publications to users. Constructive comments and suggestions by readers of the Minerals Yearbook are welcomed.

Considerations in reviewing the waste volume reduction program in a large utility

International Nuclear Information System (INIS)

Kohout, R.; Calzolari, L.M.

1987-01-01

A program is underway at Ontario Hydro to establish a desirable future scheme for central processing/volume reduction of solid radioactive Low-Level Wastes (LLW) prior to their placement into the centralized storage, and in the future into a disposal facility. The approach being investigated is to furnish the current Waste Volume Reduction Facility (WVRF) with state-of-art processes, reclassify the waste categories and segregate the wastes such that each volume reduction (VR) process is then applied where it would be most effective. The ''optimized'' approach is then compared with other, specific schemes, which basically differ in that each scheme omits one of the major VR processes, thus allowing the next most effective process to take over its role. Each scheme is assessed quantitatively from the viewpoint of cost and VR effectiveness, and qualitatively from the viewpoint of resultant waste form. The economic assessments take into consideration the long term (20 year) impact of selected VR schemes on the overall waste management cost, including construction and operation of the storage facility. This paper highlights the overall study, includes the major results, and identifies aspects that need to be addressed in the selection of a desirable combination of VR processes in absence of knowledge of future waste disposal costs

An adaptive maneuvering logic computer program for the simulation of one-on-one air-to-air combat. Volume 1: General description

Science.gov (United States)

Burgin, G. H.; Fogel, L. J.; Phelps, J. P.

1975-01-01

A technique for computer simulation of air combat is described. Volume 1 decribes the computer program and its development in general terms. Two versions of the program exist. Both incorporate a logic for selecting and executing air combat maneuvers with performance models of specific fighter aircraft. In the batch processing version the flight paths of two aircraft engaged in interactive aerial combat and controlled by the same logic are computed. The realtime version permits human pilots to fly air-to-air combat against the adaptive maneuvering logic (AML) in Langley Differential Maneuvering Simulator (DMS). Volume 2 consists of a detailed description of the computer programs.

Pilot scale refinning of crude soybean oil | Mensah | Journal of ...

African Journals Online (AJOL)

Pilot scale refinning of crude soybean oil. ... Abstract. A laboratory process for refining soybean has been scaled up to a 145 tonne per annum pilot plant to refine crude soybean oil. ... The quality of the refined oil was found to be within national and codex standard specifications for edible oil from vegetable sources.

Technological studies on uranium refining at nuclear materials authority, Egypt

International Nuclear Information System (INIS)

Mohammed, H.S.

1997-01-01

In 1992 nuclear materials authority (NMA) took a decision to establish yellow cake refining. Unit so as to study refining of El-Atshan yellow cake which recently produced by ion-exchange pilot plant, production sector. The research studies followed the conventional refining rout to produce nuclear grade UO 3 . This implies investigations on some common solvents to refine the cake viz. tri alkyl phosphates, tri alkyl phosphine oxides, dialkyl phosphoric acid as well as high-molecular weight long-chain tertiary amines. Moreover, non-conventional refining process has also been presented depending on the selectivity of uranyl ion to be dissolved by carbonate and to be precipitated by hydrogen peroxide. Most of the proposed processes were found feasible to refine El-Atshan yellow cake. however, the non- conventional refining process appears to be the most promising, owing to its superior performance and economy

Cavitation-aided grain refinement in aluminium alloys

NARCIS (Netherlands)

Atamanenko, T.V.

2010-01-01

This thesis deals with grain refinement under the influence of ultrasonic-driven cavitation in aluminium casting processes. Three major goals of this research were: (1) to identify the mechanism of the cavitation-aided grain refinement at different stages of solidification; (2) to reveal the

40 CFR 80.169 - Liability for violations of the detergent certification program controls and prohibitions.

Science.gov (United States)

2010-07-01

... review of product transfer documents by the refiner to ensure compliance with such contractual obligation..., a periodic review of its supporting product transfer and volume measurement documents to confirm the... refined, imported, manufactured, sold, offered for sale, dispensed, supplied, offered for supply, stored...

A posteriori estimator and adaptive mesh refinement for finite volume finite element method for monophasic flow and solute transport in porous media

International Nuclear Information System (INIS)

Amor, H.; Bourgeois, M.

2012-01-01

Document available in extended abstract form only. The disposal of high level, long lived waste in deep underground clay formations is investigated by several countries including France. In the safety assessment of such geological repositories, a thoughtful consideration must be given to the mechanisms and possible pathways of migration of radionuclides released from waste packages. However, when modelling the transfer of radionuclides throughout the disposal facilities and geological formations, the numerical simulations must take into consideration, in addition to long durations of concern, the variety in the properties as well as in geometrical scales of the different components of the overall disposal, including the host formation. This task presents significant computational challenges. Numerical methods used in the MELODIE software The MELODIE software is developed by IRSN, and constantly upgraded, with the aim to assess the long-term containment capabilities of underground and surface radioactive waste repositories. The MELODIE software models water flow and the phenomena involved in the transport of radionuclides in saturated and unsaturated porous media in 2 and 3 dimensions; chemical processes are represented by a retardation factor and a solubility limit, for sorption and solubility respectively, integrated in the computational equations. These equations are discretized using a so-called Finite Volume Finite Element method (FVFE), which is based on a Galerkin method to discretize time and variables, together with a Finite Volume method using the Godunov scheme for the convection term. The FVFE method is used to convert partial differential equations into a finite number of algebraic equations that match the number of nodes in the mesh used to model the considered domain. It is also used to stabilise the numerical scheme. In order to manage the variety in properties and geometrical scales of underground disposal components, an a posteriori error estimator

MODIFIED N.R.C. VERSION OF THE U.S.G.S. SOLUTE TRANSPORT MODEL. VOLUME 2. INTERACTIVE PREPROCESSOR PROGRAM

Science.gov (United States)

The methods described in the report can be used with the modified N.R.C. version of the U.S.G.S. Solute Transport Model to predict the concentration of chemical parameters in a contaminant plume. The two volume report contains program documentation and user's manual. The program ...

Optimization bitumen-based upgrading and refining schemes

Energy Technology Data Exchange (ETDEWEB)

Munteanu, M.; Chen, J. [National Centre for Upgrading Technology, Devon, AB (Canada); Natural Resources Canada, Devon, AB (Canada). CanmetENERGY

2009-07-01

This poster highlighted the results of a study in which the entire refining scheme for Canadian bitumen as feedstocks was modelled and simulated under different process configurations, operating conditions and product structures. The aim of the study was to optimize the economic benefits, product quality and energy use under a range of operational scenarios. Optimal refining schemes were proposed along with process conditions for existing refinery configurations and objectives. The goal was to provide guidelines and information for upgrading and refining process design and retrofitting. Critical steps were identified with regards to the upgrading process. It was concluded that the information obtained from this study would lead to significant improvement in process performance and operations, and in reducing the capital cost for building new upgraders and refineries. The simulation results provided valuable information for increasing the marketability of bitumen, reducing greenhouse gas emissions and other environmental impacts associated with bitumen upgrading and refining. tabs., figs.

1991 worldwide refining and gas processing directory

International Nuclear Information System (INIS)

Anon.

1990-01-01

This book ia an authority for immediate information on the industry. You can use it to find new business, analyze market trends, and to stay in touch with existing contacts while making new ones. The possibilities for business applications are numerous. Arranged by country, all listings in the directory include address, phone, fax and telex numbers, a description of the company's activities, names of key personnel and their titles, corporate headquarters, branch offices and plant sites. This newly revised edition lists more than 2000 companies and nearly 3000 branch offices and plant locations. This east-to-use reference also includes several of the most vital and informative surveys of the industry, including the U.S. Refining Survey, the Worldwide Construction Survey in Refining, Sulfur, Gas Processing and Related Fuels, the Worldwide Refining and Gas Processing Survey, the Worldwide Catalyst Report, and the U.S. and Canadian Lube and Wax Capacities Report from the National Petroleum Refiner's Association

Morphological pyramids in multiresolution MIP rendering of large volume data : Survey and new results

NARCIS (Netherlands)

Roerdink, J.B.T.M.

We survey and extend nonlinear signal decompositions based on morphological pyramids, and their application to multiresolution maximum intensity projection (MIP) volume rendering with progressive refinement and perfect reconstruction. The structure of the resulting multiresolution rendering

A Macdonald refined topological vertex

Science.gov (United States)

Foda, Omar; Wu, Jian-Feng

2017-07-01

We consider the refined topological vertex of Iqbal et al (2009 J. High Energy Phys. JHEP10(2009)069), as a function of two parameters ≤ft\\lgroup x, y \\right\\rgroup , and deform it by introducing the Macdonald parameters ≤ft\\lgroup q, t \\right\\rgroup , as in the work of Vuletić on plane partitions (Vuletić M 2009 Trans. Am. Math. Soc. 361 2789-804), to obtain ‘a Macdonald refined topological vertex’. In the limit q → t , we recover the refined topological vertex of Iqbal et al and in the limit x → y , we obtain a qt-deformation of the original topological vertex of Aganagic et al (2005 Commun. Math. Phys. 25 425-78). Copies of the vertex can be glued to obtain qt-deformed 5D instanton partition functions that have well-defined 4D limits and, for generic values of ≤ft\\lgroup q, t\\right\\rgroup , contain infinite-towers of poles for every pole present in the limit q → t .

RELAP4/MOD5: a computer program for transient thermal-hydraulic analysis of nuclear reactors and related systems. User's manual. Volume II. Program implementation

International Nuclear Information System (INIS)

1976-06-01

A discussion is presented of the use of the RELAP4/MOD5 computer program in simulating the thermal-hydraulic behavior of light-water reactor systems when subjected to postulated transients such as a LOCA, pump failure, or nuclear excursion. The volume is divided into main sections which cover: (1) program description, (2) input data, (3) problem initialization, (4) user guidelines, (5) output discussion, (6) source program description, (7) implementation requirements, (8) data files, (9) description of PLOTR4M, (10) description of STH20, (11) summary flowchart, (12) sample problems, (13) problem definition, and (14) problem input

Modified process for refining niobium by electron beam

International Nuclear Information System (INIS)

Pinatti, D.G.; Takano, C.

1982-01-01

The experimental results, thermodynamic equilibrium and kinetic theory of the metal/gas interaction in refractory metals are reviewed. The adsorption and desorption of nitrogen, hydrogen and CO are reversible, whereas those of oxygen are irreversible, with adsorption of an oxygen atom and volatilisation of the metal oxide. Based upon this fact, a new electron beam refining technology is proposed for niobium, consisting of four points: preparation of an electrode by aluminothermic reduction; zone refining in the first melt; kinetic refining in subsequent melts and compact design of the refining plant. Experimental results from a 300 kW pilot plant were in complete agreement with the technology proposed, giving 2.4 times the productivity predicted by the conventional technology. (Author) [pt

Grain refinement of AZ31 magnesium alloy by electromagnetic ...

Indian Academy of Sciences (India)

Low-frequency electromagnetic field; AZ31 magnesium alloy; Al4C3; grain refinement. Abstract. The effects of electromagnetic stirring and Al4C3 grain refiner on the grain refinement of semicontinuously cast AZ31 magnesium alloy were discussed in this investigation. The results indicate that electromagnetic stirring has an ...

Refinement of RAIM via Implementation of Implicit Euler Method

Energy Technology Data Exchange (ETDEWEB)

Lee, Yoonhee; Kim, Han-Chul [Korea Institute of Nuclear and Safety, Daejeon (Korea, Republic of)

2016-10-15

The first approach is a mechanistic approach which is used in LIRIC in which more than 200 reactions are modeled in detail. This approach enables to perform the detailed analysis. However, it requires huge computation burden. The other approach is a simplified model approach which is used in the IMOD, ASTEC/IODE, and etc. Recently, KINS has developed RAIM (Radio-Active Iodine chemistry Model) based on the simplified model approach. Since the numerical analysis module in RAIM is based on the explicit Euler method, there are major issues on the stability of the module. Therefore, implementation of a stable numerical method becomes essential. In this study, RAIM is refined via implementation of implicit Euler method in which the Newton method is used to find the solutions at each time step. The refined RAIM is tested by comparing to RAIM based on the explicit Euler method. In this paper, RAIM was refined by implementing the implicit Euler method. At each time step of the method in the refined RAIM, the reaction kinetics equations are solved by the Newton method in which elements of the Jacobian matrix are expressed analytically. With the results of OECD-BIP P10T2 test, the refined RAIM was compared to RAIM with the explicit Euler method. The refined RAIM shows better agreement with the experimental data than those from the explicit Euler method. For the rapid change of pH during the experiment, the refined RAIM gives more realistic changes in the concentrations of chemical species than those from the explicit Euler method. In addition, in terms of computing time, the refined RAIM shows comparable computing time to that with explicit Euler method. These comparisons are attributed to ⁓10 times larger time step size used in the implicit Euler method, even though computation burden at each time step in the refined RAIM is much higher than that of the explicit Euler method. Compared to the experimental data, the refined RAIM still shows discrepancy, which are attributed

Refinement of RAIM via Implementation of Implicit Euler Method

International Nuclear Information System (INIS)

Lee, Yoonhee; Kim, Han-Chul

2016-01-01

The first approach is a mechanistic approach which is used in LIRIC in which more than 200 reactions are modeled in detail. This approach enables to perform the detailed analysis. However, it requires huge computation burden. The other approach is a simplified model approach which is used in the IMOD, ASTEC/IODE, and etc. Recently, KINS has developed RAIM (Radio-Active Iodine chemistry Model) based on the simplified model approach. Since the numerical analysis module in RAIM is based on the explicit Euler method, there are major issues on the stability of the module. Therefore, implementation of a stable numerical method becomes essential. In this study, RAIM is refined via implementation of implicit Euler method in which the Newton method is used to find the solutions at each time step. The refined RAIM is tested by comparing to RAIM based on the explicit Euler method. In this paper, RAIM was refined by implementing the implicit Euler method. At each time step of the method in the refined RAIM, the reaction kinetics equations are solved by the Newton method in which elements of the Jacobian matrix are expressed analytically. With the results of OECD-BIP P10T2 test, the refined RAIM was compared to RAIM with the explicit Euler method. The refined RAIM shows better agreement with the experimental data than those from the explicit Euler method. For the rapid change of pH during the experiment, the refined RAIM gives more realistic changes in the concentrations of chemical species than those from the explicit Euler method. In addition, in terms of computing time, the refined RAIM shows comparable computing time to that with explicit Euler method. These comparisons are attributed to ⁓10 times larger time step size used in the implicit Euler method, even though computation burden at each time step in the refined RAIM is much higher than that of the explicit Euler method. Compared to the experimental data, the refined RAIM still shows discrepancy, which are attributed

The European refining and distribution industry at the 2010 vista

International Nuclear Information System (INIS)

Lacour, J.J.; Tessmer, G.; Ward, I.

1998-01-01

Oil company chairmen belonging to the AFTP, DGMK and IP associations met together to debate about the future of the European refining industry. The following topics were discussed: is it the end of the refining crisis? Which uncertainties will have to be met? What is the situation of petroleum products supply and demand? What are the consumers' expectations? How to face the environmental constraints? Which future for the refining activities in Europe? Seven round-tables took place with the following themes: the factors of uncertainty in the future of refining activities, the petroleum products supply and demand (automotive fuels, fuel oils, lubricants), the refining activities and the supply of consumers (service stations and supermarkets), the situation of the European petroleum policy, the European refining industry and the public regulations (development of more efficient environmental approaches), the impact of environmental constraints and the technical solutions, and the future of the refining industry. (J.S.)

Zone refining high-purity germanium

International Nuclear Information System (INIS)

Hubbard, G.S.; Haller, E.E.; Hansen, W.L.

1977-10-01

The effects of various parameters on germanium purification by zone refining have been examined. These parameters include the germanium container and container coatings, ambient gas and other operating conditions. Four methods of refining are presented which reproducibly yield 3.5 kg germanium ingots from which high purity (vertical barN/sub A/ - N/sub D/vertical bar less than or equal to2 x 10 10 cm -3 ) single crystals can be grown. A qualitative model involving binary and ternary complexes of Si, O, B, and Al is shown to account for the behavior of impurities at these low concentrations

Refining processes of selected copper alloys

Directory of Open Access Journals (Sweden)

S. Rzadkosz

2009-04-01

Full Text Available The analysis of the refining effectiveness of the liquid copper and selected copper alloys by various micro additions and special refiningsubstances – was performed. Examinations of an influence of purifying, modifying and deoxidation operations performed in a metal bath on the properties of certain selected alloys based on copper matrix - were made. Refining substances, protecting-purifying slag, deoxidation and modifying substances containing micro additions of such elements as: zirconium, boron, phosphor, sodium, lithium, or their compounds introduced in order to change micro structures and properties of alloys, were applied in examinations. A special attention was directed to macro and micro structures of alloys, their tensile and elongation strength and hot-cracks sensitivity. Refining effects were estimated by comparing the effectiveness of micro structure changes with property changes of copper and its selected alloys from the group of tin bronzes.

Refinement of the ferri and paramagnetic phases of magnetite measured by neutron multiple diffraction

International Nuclear Information System (INIS)

Mazzochi, V.L.; Parente, C.B.R.

1989-10-01

Structural parameters of the ferri and paramagnetic phases of magnetite have been refined from neutron multiple diffraction data. Experimental patterns were obtained by measuring the III primary reflection of a natural single crystal of this compound, at room temperature for the ferrimagnetic phase and 703 0 C for the paramagnetic phase. Theoretical multiple diffraction patterns for both phases have been calculated by the program MULTI which uses the iterative method. In this method intensities are caluclated as Taylor series expansions summed up to a order sufficient for a good approximation. A step by step process has been used in the refinements similarly to the parameter-shift method. Final values for the discrepancy factor found for the ferri and paramagnetic phases were R = 3.96% and R = 3.46%, respectively. (author) [pt

Adaptive mesh refinement for shocks and material interfaces

Energy Technology Data Exchange (ETDEWEB)

Dai, William Wenlong [Los Alamos National Laboratory

2010-01-01

There are three kinds of adaptive mesh refinement (AMR) in structured meshes. Block-based AMR sometimes over refines meshes. Cell-based AMR treats cells cell by cell and thus loses the advantage of the nature of structured meshes. Patch-based AMR is intended to combine advantages of block- and cell-based AMR, i.e., the nature of structured meshes and sharp regions of refinement. But, patch-based AMR has its own difficulties. For example, patch-based AMR typically cannot preserve symmetries of physics problems. In this paper, we will present an approach for a patch-based AMR for hydrodynamics simulations. The approach consists of clustering, symmetry preserving, mesh continuity, flux correction, communications, management of patches, and load balance. The special features of this patch-based AMR include symmetry preserving, efficiency of refinement across shock fronts and material interfaces, special implementation of flux correction, and patch management in parallel computing environments. To demonstrate the capability of the AMR framework, we will show both two- and three-dimensional hydrodynamics simulations with many levels of refinement.

Regulatory Oversight Program, July 1, 1993--March 3, 1997. Volume 2: Appendices

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-12-31

On July, 1993, a Regulatory Oversight (RO) organization was established within the US DOE, Oak Ridge Operations to provide regulatory oversight of the DOE uranium enrichment facilities leased to the United States Enrichment Corporation (USEC). The purpose of the OR program was to ensure continued plant safety, safeguards and security while the plants were transitioned to regulatory oversight by the Nuclear Regulatory Commission (NRC). Volume 2 contains copies of the documents which established the relationship between NRC, DOE, USEC, and DOL (Dept of Labor) required to facilitate regulatory oversight transition.

Regulatory Oversight Program, July 1, 1993 - March 3, 1997. Volume 2: Appendices

International Nuclear Information System (INIS)

1997-01-01

On July, 1993, a Regulatory Oversight (RO) organization was established within the US DOE, Oak Ridge Operations to provide regulatory oversight of the DOE uranium enrichment facilities leased to the United States Enrichment Corporation (USEC). The purpose of the OR program was to ensure continued plant safety, safeguards and security while the plants were transitioned to regulatory oversight by the Nuclear Regulatory Commission (NRC). Volume 2 contains copies of the documents which established the relationship between NRC, DOE, USEC, and DOL (Dept of Labor) required to facilitate regulatory oversight transition

Chinese refining capacity for Canadian heavy oil

International Nuclear Information System (INIS)

Bruce, G.W.

2006-01-01

This paper discussed China's refining capacity in relation to exports of Canadian heavy oil. Demand for oil is increasing throughout the world, and China is expected to consume 25 per cent of the projected yearly oil supplies. Alberta currently has an estimated 174 billion barrels of recoverable bitumen, and produces 1.06 million barrels per day. Production is expected to increase to 4.5 million barrels per day by the year 2020. Currently bitumen blends are refined and diluted with naphtha and sweet synthetic crude oil. Bitumen is a challenging feedstock for refineries, and requires thermal production methods or gasification processes. Primary conversion into sour synthetic crude is typically followed by hydrocracking and further refining into finished petroleum products. There are currently 50 refineries in China with a 7.4 million barrel per day capacity. Coastal refineries using imported crude oil have a 4 million barrel per day capacity. New facilities are being constructed and existing plants are being upgraded in order to process heavier and more sour crude oils. However, current refining capabilities in Chinese refineries have a limited ability for resid conversion. It was concluded that while China has a refining infrastructure, only refineries on the coast will use oil sands-derived feedstocks. However, there are currently opportunities to design refineries to match future feedstocks. tabs., figs

On macromolecular refinement at subatomic resolution with interatomic scatterers

Energy Technology Data Exchange (ETDEWEB)

Afonine, Pavel V., E-mail: pafonine@lbl.gov; Grosse-Kunstleve, Ralf W.; Adams, Paul D. [Lawrence Berkeley National Laboratory, One Cyclotron Road, BLDG 64R0121, Berkeley, CA 94720 (United States); Lunin, Vladimir Y. [Institute of Mathematical Problems of Biology, Russian Academy of Sciences, Pushchino 142290 (Russian Federation); Urzhumtsev, Alexandre [IGMBC, 1 Rue L. Fries, 67404 Illkirch and IBMC, 15 Rue R. Descartes, 67084 Strasbourg (France); Faculty of Sciences, Nancy University, 54506 Vandoeuvre-lès-Nancy (France); Lawrence Berkeley National Laboratory, One Cyclotron Road, BLDG 64R0121, Berkeley, CA 94720 (United States)

2007-11-01

Modelling deformation electron density using interatomic scatters is simpler than multipolar methods, produces comparable results at subatomic resolution and can easily be applied to macromolecules. A study of the accurate electron-density distribution in molecular crystals at subatomic resolution (better than ∼1.0 Å) requires more detailed models than those based on independent spherical atoms. A tool that is conventionally used in small-molecule crystallography is the multipolar model. Even at upper resolution limits of 0.8–1.0 Å, the number of experimental data is insufficient for full multipolar model refinement. As an alternative, a simpler model composed of conventional independent spherical atoms augmented by additional scatterers to model bonding effects has been proposed. Refinement of these mixed models for several benchmark data sets gave results that were comparable in quality with the results of multipolar refinement and superior to those for conventional models. Applications to several data sets of both small molecules and macromolecules are shown. These refinements were performed using the general-purpose macromolecular refinement module phenix.refine of the PHENIX package.

Review of Grain Refinement of Cast Metals Through Inoculation: Theories and Developments

Science.gov (United States)

Liu, Zhilin

2017-10-01

The inoculation method of grain refinement is widely used in research and industry. Because of its commercial and engineering importance, extensive research on the mechanisms/theories of grain refinement and development of effective grain refiners for diverse cast metals/alloys has been conducted. In 1999, Easton and St. John reviewed the mechanisms of grain refinement of cast Al alloys. Since then, grain refinement in alloys of Al, Mg, Fe, Ti, Cu, and Zn has evolved a lot. However, there is still no full consensus on the mechanisms/theories of grain refinement. Moreover, some new grain refiners developed based on the theories do not ensure efficient grain refinement. Thus, the factors that contribute to grain refinement are still not fully understood. Clarification of the prerequisite issues that occur in grain refinement is required using recent theories. This review covers multiple metals/alloys and developments in grain refinement from the last twenty years. The characteristics of effective grain refiners are considered from four perspectives: effective particle/matrix wetting configuration, sufficiently powerful segregating elements, preferential crystallographic matching, and geometrical features of effective nucleants. Then, recent mechanisms/theories on the grain refinement of cast metals/alloys are reviewed, including the peritectic-related, hypernucleation, inert nucleant, and constitutional supercooling-driven theories. Further, developments of deterministic and probabilistic modeling and nucleation crystallography in the grain refinement of cast metals are reviewed. Finally, the latest progress in the grain refinement of cast Zn and its alloys is described, and future work on grain refinement is summarized.

Total antioxidant content of alternatives to refined sugar.

Science.gov (United States)

Phillips, Katherine M; Carlsen, Monica H; Blomhoff, Rune

2009-01-01

Oxidative damage is implicated in the etiology of cancer, cardiovascular disease, and other degenerative disorders. Recent nutritional research has focused on the antioxidant potential of foods, while current dietary recommendations are to increase the intake of antioxidant-rich foods rather than supplement specific nutrients. Many alternatives to refined sugar are available, including raw cane sugar, plant saps/syrups (eg, maple syrup, agave nectar), molasses, honey, and fruit sugars (eg, date sugar). Unrefined sweeteners were hypothesized to contain higher levels of antioxidants, similar to the contrast between whole and refined grain products. To compare the total antioxidant content of natural sweeteners as alternatives to refined sugar. The ferric-reducing ability of plasma (FRAP) assay was used to estimate total antioxidant capacity. Major brands of 12 types of sweeteners as well as refined white sugar and corn syrup were sampled from retail outlets in the United States. Substantial differences in total antioxidant content of different sweeteners were found. Refined sugar, corn syrup, and agave nectar contained minimal antioxidant activity (sugar had a higher FRAP (0.1 mmol/100 g). Dark and blackstrap molasses had the highest FRAP (4.6 to 4.9 mmol/100 g), while maple syrup, brown sugar, and honey showed intermediate antioxidant capacity (0.2 to 0.7 mmol FRAP/100 g). Based on an average intake of 130 g/day refined sugars and the antioxidant activity measured in typical diets, substituting alternative sweeteners could increase antioxidant intake an average of 2.6 mmol/day, similar to the amount found in a serving of berries or nuts. Many readily available alternatives to refined sugar offer the potential benefit of antioxidant activity.

Investment in exploration-production and refining 2015

International Nuclear Information System (INIS)

Maisonnier, G.; Hureau, G.; Serbutoviez, S.; Silva, C.

2016-01-01

IFPEN analyses in this study the 2015 evolution of global investment in the field of exploration-production and refining: - Changes in oil and gas prices; - Investment in Exploration/Production: the end of an upward cycle; - Drilling and the global drilling market, upstream activities and markets; - 2015, a breath of fresh air for refining

Hirshfeld atom refinement.

Science.gov (United States)

Capelli, Silvia C; Bürgi, Hans-Beat; Dittrich, Birger; Grabowsky, Simon; Jayatilaka, Dylan

2014-09-01

Hirshfeld atom refinement (HAR) is a method which determines structural parameters from single-crystal X-ray diffraction data by using an aspherical atom partitioning of tailor-made ab initio quantum mechanical molecular electron densities without any further approximation. Here the original HAR method is extended by implementing an iterative procedure of successive cycles of electron density calculations, Hirshfeld atom scattering factor calculations and structural least-squares refinements, repeated until convergence. The importance of this iterative procedure is illustrated via the example of crystalline ammonia. The new HAR method is then applied to X-ray diffraction data of the dipeptide Gly-l-Ala measured at 12, 50, 100, 150, 220 and 295 K, using Hartree-Fock and BLYP density functional theory electron densities and three different basis sets. All positions and anisotropic displacement parameters (ADPs) are freely refined without constraints or restraints - even those for hydrogen atoms. The results are systematically compared with those from neutron diffraction experiments at the temperatures 12, 50, 150 and 295 K. Although non-hydrogen-atom ADPs differ by up to three combined standard uncertainties (csu's), all other structural parameters agree within less than 2 csu's. Using our best calculations (BLYP/cc-pVTZ, recommended for organic molecules), the accuracy of determining bond lengths involving hydrogen atoms from HAR is better than 0.009 Å for temperatures of 150 K or below; for hydrogen-atom ADPs it is better than 0.006 Å(2) as judged from the mean absolute X-ray minus neutron differences. These results are among the best ever obtained. Remarkably, the precision of determining bond lengths and ADPs for the hydrogen atoms from the HAR procedure is comparable with that from the neutron measurements - an outcome which is obtained with a routinely achievable resolution of the X-ray data of 0.65 Å.

Creating a simplified model of oil refining and solution of the model using a linear programming method. Part 1, Model presentation

Energy Technology Data Exchange (ETDEWEB)

Duric, M; Novakovic, M; Stojkanovic, L

1983-01-01

Based on a detailed analysis of technological limitations in oil refining at an oil refinery (NPZ) in the separation of petroleum products, specifications with regard to quality and market limitations, a general model is created of oil refining. The number of actual variables is reduced to a minimum, while the number of linear limitations is adapted to the selected technology and raw material quality. The nonlinearity of certain characteristics is overcome using the so called movement factor.

Stepwise-refinement for performance: a methodology for many-core programming

NARCIS (Netherlands)

Hijma, P.; van Nieuwpoort, R.V.; Jacobs, C.J.H.; Bal, H.E.

2015-01-01

Many-core hardware is targeted specifically at obtaining high performance, but reaching high performance is often challenging because hardware-specific details have to be taken into account. Although there are many programming systems that try to alleviate many-core programming, some providing a

Biomolecular structure refinement using the GROMOS simulation software

International Nuclear Information System (INIS)

Schmid, Nathan; Allison, Jane R.; Dolenc, Jožica; Eichenberger, Andreas P.; Kunz, Anna-Pitschna E.; Gunsteren, Wilfred F. van

2011-01-01

For the understanding of cellular processes the molecular structure of biomolecules has to be accurately determined. Initial models can be significantly improved by structure refinement techniques. Here, we present the refinement methods and analysis techniques implemented in the GROMOS software for biomolecular simulation. The methodology and some implementation details of the computation of NMR NOE data, 3 J-couplings and residual dipolar couplings, X-ray scattering intensities from crystals and solutions and neutron scattering intensities used in GROMOS is described and refinement strategies and concepts are discussed using example applications. The GROMOS software allows structure refinement combining different types of experimental data with different types of restraining functions, while using a variety of methods to enhance conformational searching and sampling and the thermodynamically calibrated GROMOS force field for biomolecular simulation.

Biomolecular structure refinement using the GROMOS simulation software

Energy Technology Data Exchange (ETDEWEB)

Schmid, Nathan; Allison, Jane R.; Dolenc, Jozica; Eichenberger, Andreas P.; Kunz, Anna-Pitschna E.; Gunsteren, Wilfred F. van, E-mail: wfvgn@igc.phys.chem.ethz.ch [Swiss Federal Institute of Technology ETH, Laboratory of Physical Chemistry (Switzerland)

2011-11-15

For the understanding of cellular processes the molecular structure of biomolecules has to be accurately determined. Initial models can be significantly improved by structure refinement techniques. Here, we present the refinement methods and analysis techniques implemented in the GROMOS software for biomolecular simulation. The methodology and some implementation details of the computation of NMR NOE data, {sup 3}J-couplings and residual dipolar couplings, X-ray scattering intensities from crystals and solutions and neutron scattering intensities used in GROMOS is described and refinement strategies and concepts are discussed using example applications. The GROMOS software allows structure refinement combining different types of experimental data with different types of restraining functions, while using a variety of methods to enhance conformational searching and sampling and the thermodynamically calibrated GROMOS force field for biomolecular simulation.

Pakistan stepping up expansion of refining, transportation sectors

International Nuclear Information System (INIS)

Anon.

1992-01-01

This paper reports that Pakistan is taking steps to speed expansion of its refining and oil transportation infrastructure. While the country has made significant progress toward energy self-efficiency by boosting oil and gas production it still must modernize and expand an aging, inadequate refining sector to meet rapidly growing demand for refined products. Pakistan's government has disclosed plans to build two refineries in the country, one at Rawalpindi near a string of recent oil discoveries, the other somewhere in the southern part of the country, likely Karachi. At the same time, efforts are proceeding to upgrade Pakistan's refineries. In addition, Pakistani state companies continue to press joint ventures in refining and marketing with foreign companies and expand downstream ties with neighbors that are key oil and gas exporters

Minerals Yearbook, volume III, Area Reports—International—Africa and the Middle East

Science.gov (United States)

,

2018-01-01

The U.S. Geological Survey (USGS) Minerals Yearbook discusses the performance of the worldwide minerals and materials industries and provides background information to assist in interpreting that performance. Content of the individual Minerals Yearbook volumes follows:Volume I, Metals and Minerals, contains chapters about virtually all metallic and industrial mineral commodities important to the U.S. economy. Chapters on survey methods, summary statistics for domestic nonfuel minerals, and trends in mining and quarrying in the metals and industrial mineral industries in the United States are also included.Volume II, Area Reports: Domestic, contains a chapter on the mineral industry of each of the 50 States and Puerto Rico and the Administered Islands. This volume also has chapters on survey methods and summary statistics of domestic nonfuel minerals.Volume III, Area Reports: International, is published as four separate reports. These regional reports contain the latest available minerals data on more than 180 foreign countries and discuss the importance of minerals to the economies of these nations and the United States. Each report begins with an overview of the region’s mineral industries during the year. It continues with individual country chapters that examine the mining, refining, processing, and use of minerals in each country of the region and how each country’s mineral industry relates to U.S. industry. Most chapters include production tables and industry structure tables, information about Government policies and programs that affect the country’s mineral industry, and an outlook section.The USGS continually strives to improve the value of its publications to users. Constructive comments and suggestions by readers of the Minerals Yearbook are welcomed.

NASA Aerospace Flight Battery Program: Wet Life of Nickel-Hydrogen (Ni-H2) Batteries. Volume 2, Part 3; Appendices

Science.gov (United States)

Jung, David S,; Lee, Leonine S.; Manzo, Michelle A.

2010-01-01

This NASA Aerospace Flight Battery Systems Working Group was chartered within the NASA Engineering and Safety Center (NESC). The Battery Working Group was tasked to complete tasks and to propose proactive work to address battery related, agency-wide issues on an annual basis. In its first year of operation, this proactive program addressed various aspects of the validation and verification of aerospace battery systems for NASA missions. Studies were performed, issues were discussed and in many cases, test programs were executed to generate recommendations and guidelines to reduce risk associated with various aspects of implementing battery technology in the aerospace industry. This document contains Part 3 - Volume II Appendices to Part 3 - Volume I.

Decontamination of metals by melt refinings/slagging: An annotated bibliography

International Nuclear Information System (INIS)

Mizia, R.E.; Worcester, S.A.; Twidwell, L.G.; Paolini, D.J.; Weldon, T.A.

1993-07-01

As the number of nuclear installations undergoing decontamination and decommissioning (D ampersand D) increases, current radioactive waste storage space is consumed and establishment of new waste storage areas becomes increasingly difficult, the problem of handling and storing radioactive scrap metal (RSM) gains increasing importance in the DOE Environmental Restoration and Waste Management Program. To alleviate present and future waste storage problems, Westinghouse Idaho Nuclear Company (WINCO) is managing a program for the recycling of RSM for beneficial use within the DOE complex. As part of that effort, Montana Tech has been awarded a contract to help optimize melting and refining technology for the recycling of stainless steel RSM. The scope of the Montana Tech program includes a literature survey, a decontaminating slag design study, small scale melting studies to determine optimum slag compositions for removal of radioactive contaminant surrogates, analysis of preferred melting techniques, and coordination of large scale melting demonstrations (100--500 lbs) to be conducted at selected facilities. The program will support recycling and decontaminating stainless steel RSM for use in waste canisters for Idaho Waste Immobilization Facility densified high level waste. This report is the result of the literature search conducted to establish a basis for experimental melt/slag program development

Decontamination of metals by melt refinings/slagging: An annotated bibliography

Energy Technology Data Exchange (ETDEWEB)

Mizia, R.E. [ed.; Worcester, S.A.; Twidwell, L.G.; Paolini, D.J.; Weldon, T.A.

1993-07-01

As the number of nuclear installations undergoing decontamination and decommissioning (D&D) increases, current radioactive waste storage space is consumed and establishment of new waste storage areas becomes increasingly difficult, the problem of handling and storing radioactive scrap metal (RSM) gains increasing importance in the DOE Environmental Restoration and Waste Management Program. To alleviate present and future waste storage problems, Westinghouse Idaho Nuclear Company (WINCO) is managing a program for the recycling of RSM for beneficial use within the DOE complex. As part of that effort, Montana Tech has been awarded a contract to help optimize melting and refining technology for the recycling of stainless steel RSM. The scope of the Montana Tech program includes a literature survey, a decontaminating slag design study, small scale melting studies to determine optimum slag compositions for removal of radioactive contaminant surrogates, analysis of preferred melting techniques, and coordination of large scale melting demonstrations (100--500 lbs) to be conducted at selected facilities. The program will support recycling and decontaminating stainless steel RSM for use in waste canisters for Idaho Waste Immobilization Facility densified high level waste. This report is the result of the literature search conducted to establish a basis for experimental melt/slag program development.

Simultaneous use of solution NMR and X-ray data in REFMAC5 for joint refinement/detection of structural differences

Energy Technology Data Exchange (ETDEWEB)

Rinaldelli, Mauro; Ravera, Enrico; Calderone, Vito; Parigi, Giacomo [University of Florence, Via L. Sacconi 6, 50019 Sesto Fiorentino (Finland) (Italy); University of Florence, Via della Lastruccia 3, 50019 Sesto Fiorentino (Finland) (Italy); Murshudov, Garib N., E-mail: garib@mrc-lmb.cam.ac.uk [MRC Laboratory of Molecular Biology, Francis Crick Avenue, Cambridge Biomedical Campus, Cambridge CB2 0QH (United Kingdom); Luchinat, Claudio, E-mail: garib@mrc-lmb.cam.ac.uk [University of Florence, Via L. Sacconi 6, 50019 Sesto Fiorentino (Finland) (Italy); University of Florence, Via della Lastruccia 3, 50019 Sesto Fiorentino (Finland) (Italy)

2014-04-01

Paramagnetic NMR data (pseudocontact shifts and self-orientation residual dipolar couplings) and diamagnetic residual dipolar couplings can now be used in the program REFMAC5 from CCP4 as structural restraints together with X-ray crystallographic data. These NMR restraints can reveal differences between solid state and solution conformations of molecules or, in their absence, can be used together with X-ray crystallographic data for structural refinement. The program REFMAC5 from CCP4 was modified to allow the simultaneous use of X-ray crystallographic data and paramagnetic NMR data (pseudocontact shifts and self-orientation residual dipolar couplings) and/or diamagnetic residual dipolar couplings. Incorporation of these long-range NMR restraints in REFMAC5 can reveal differences between solid-state and solution conformations of molecules or, in their absence, can be used together with X-ray crystallographic data for structural refinement. Since NMR and X-ray data are complementary, when a single structure is consistent with both sets of data and still maintains reasonably ‘ideal’ geometries, the reliability of the derived atomic model is expected to increase. The program was tested on five different proteins: the catalytic domain of matrix metalloproteinase 1, GB3, ubiquitin, free calmodulin and calmodulin complexed with a peptide. In some cases the joint refinement produced a single model consistent with both sets of observations, while in other cases it indicated, outside the experimental uncertainty, the presence of different protein conformations in solution and in the solid state.

Simultaneous use of solution NMR and X-ray data in REFMAC5 for joint refinement/detection of structural differences

International Nuclear Information System (INIS)

Rinaldelli, Mauro; Ravera, Enrico; Calderone, Vito; Parigi, Giacomo; Murshudov, Garib N.; Luchinat, Claudio

2014-01-01

Paramagnetic NMR data (pseudocontact shifts and self-orientation residual dipolar couplings) and diamagnetic residual dipolar couplings can now be used in the program REFMAC5 from CCP4 as structural restraints together with X-ray crystallographic data. These NMR restraints can reveal differences between solid state and solution conformations of molecules or, in their absence, can be used together with X-ray crystallographic data for structural refinement. The program REFMAC5 from CCP4 was modified to allow the simultaneous use of X-ray crystallographic data and paramagnetic NMR data (pseudocontact shifts and self-orientation residual dipolar couplings) and/or diamagnetic residual dipolar couplings. Incorporation of these long-range NMR restraints in REFMAC5 can reveal differences between solid-state and solution conformations of molecules or, in their absence, can be used together with X-ray crystallographic data for structural refinement. Since NMR and X-ray data are complementary, when a single structure is consistent with both sets of data and still maintains reasonably ‘ideal’ geometries, the reliability of the derived atomic model is expected to increase. The program was tested on five different proteins: the catalytic domain of matrix metalloproteinase 1, GB3, ubiquitin, free calmodulin and calmodulin complexed with a peptide. In some cases the joint refinement produced a single model consistent with both sets of observations, while in other cases it indicated, outside the experimental uncertainty, the presence of different protein conformations in solution and in the solid state

Optimal algebraic multilevel preconditioning for local refinement along a line

NARCIS (Netherlands)

Margenov, S.D.; Maubach, J.M.L.

1995-01-01

The application of some recently proposed algebraic multilevel methods for the solution of two-dimensional finite element problems on nonuniform meshes is studied. The locally refined meshes are created by the newest vertex mesh refinement method. After the introduction of this refinement technique

Directory of certificates of compliance for radioactive materials packages. Volume 3, Revision 14: Report of NRC approved quality assurance programs for radioactive materials packages

International Nuclear Information System (INIS)

1994-10-01

This directory contains a Report of NRC Approved Packages (Volume 1), Certificates of Compliance (Volume 2), and a Report of NRC Approved Quality Assurance Programs for Radioactive Materials Packages (Volume 3). The purpose of this directory is to make available a convenient source of information on Quality Assurance Programs and Packagings which have been approved by the US Nuclear Regulatory Commission. Shipments of radioactive material utilizing these packagings must be in accordance with the provisions of 49 CFR section 173.471 and 10 CFR Part 71, as applicable. In satisfying the requirements of Section 71.12, it is the responsibility of the licensees to insure themselves that they have a copy of the current approval and conduct their transportation activities in accordance with an NRC approved quality assurance program

RBT—A Tool for Building Refined Buneman Trees

DEFF Research Database (Denmark)

Besenbacher, Søren; Mailund; Westh-Nielsen, Lasse

2005-01-01

We have developed a tool implementing an efficient algorithm for refined Buneman tree reconstruction. The algorithm—which has the same complexity as the neighbour-joining method and the (plain) Buneman tree construction—enables refined Buneman tree reconstruction on large taxa sets....

Utilities and offsites design baseline. Outside Battery Limits Facility 6000 tpd SRC-I Demonstration Plant. Volume 1

Energy Technology Data Exchange (ETDEWEB)

None

1984-05-25

As part of the overall Solvent Refined Coal (SRC-1) project baseline being prepared by International Coal Refining Company (ICRC), the RUST Engineering Company is providing necessary input for the Outside Battery Limits (OSBL) Facilities. The project baseline is comprised of: design baseline - technical definition of work; schedule baseline - detailed and management level 1 schedules; and cost baseline - estimates and cost/manpower plan. The design baseline (technical definition) for the OSBL Facilities has been completed and is presented in Volumes I, II, III, IV, V and VI. The OSBL technical definition is based on, and compatible with, the ICRC defined statement of work, design basis memorandum, master project procedures, process and mechanical design criteria, and baseline guidance documents. The design basis memorandum is included in Paragraph 1.3 of Volume I. The baseline design data is presented in 6 volumes. Volume I contains the introduction section and utility systems data through steam and feedwater. Volume II continues with utility systems data through fuel system, and contains the interconnecting systems and utility system integration information. Volume III contains the offsites data through water and waste treatment. Volume IV continues with offsites data, including site development and buildings, and contains raw materials and product handling and storage information. Volume V contains wastewater treatment and solid wastes landfill systems developed by Catalytic, Inc. to supplement the information contained in Volume III. Volume VI contains proprietary information of Resources Conservation Company related to the evaporator/crystallizer system of the wastewater treatment area.

India's refining prospects linked to economic growth

International Nuclear Information System (INIS)

Lewis, E.

1996-01-01

International investors assess refining ventures in India the same way they do comparable projects elsewhere in the world: according to their expectations about investment returns. By that standard, India's appeal is mixed, although its need for some measure of additional refining capacity seems certain. The success of future refinery investments will depend heavily on the government's commitment to policies allowing the economy to grow faster than the population. Unless accompanied by economic growth, expected increases in the population will not automatically raise demand for petroleum products. Decisions about investments in India's refining sector, therefore, must carefully weigh market fundamentals, the business environment, and likely investment performance. This paper reviews the market for the various products and predicts new economic trends

Global Energetics of Solar Flares. VI. Refined Energetics of Coronal Mass Ejections

Science.gov (United States)

Aschwanden, Markus J.

2017-09-01

In this study, we refine the coronal mass ejection (CME) model that was presented in an earlier study of the global energetics of solar flares and associated CMEs and apply it to all (860) GOES M- and X-class flare events observed during the first seven years (2010-2016) of the Solar Dynamics Observatory (SDO) mission. The model refinements include (1) the CME geometry in terms of a 3D volume undergoing self-similar adiabatic expansion, (2) the solar gravitational deceleration during the propagation of the CME, which discriminates between eruptive and confined CMEs, (3) a self-consistent relationship between the CME center-of-mass motion detected during EUV dimming and the leading-edge motion observed in white-light coronagraphs, (4) the equipartition of the CME’s kinetic and thermal energies, and (5) the Rosner-Tucker-Vaiana scaling law. The refined CME model is entirely based on EUV-dimming observations (using Atmospheric Imager Assembly (AIA)/SDO data) and complements the traditional white-light scattering model (using Large-Angle and Spectrometric Coronagraph Experiment (LASCO)/Solar and Heliospheric Observatory data), and both models are independently capable of determining fundamental CME parameters. Comparing the two methods, we find that (1) LASCO is less sensitive than AIA in detecting CMEs (in 24% of the cases), (2) CME masses below {m}{cme}≲ {10}14 g are underestimated by LASCO, (3) AIA and LASCO masses, speeds, and energies agree closely in the statistical mean after the elimination of outliers, and (4) the CME parameters speed v, emission measure-weighted flare peak temperature T e , and length scale L are consistent with the following scaling laws: v\\propto {T}e1/2, v\\propto {({m}{cme})}1/4, and {m}{cme}\\propto {L}2.

Development of a performance-based industrial energy efficiency indicator for corn refining plants.

Energy Technology Data Exchange (ETDEWEB)

Boyd, G. A.; Decision and Information Sciences; USEPA

2006-07-31

Organizations that implement strategic energy management programs have the potential to achieve sustained energy savings if the programs are carried out properly. A key opportunity for achieving energy savings that plant managers can take is to determine an appropriate level of energy performance by comparing their plant's performance with that of similar plants in the same industry. Manufacturing facilities can set energy efficiency targets by using performance-based indicators. The U.S. Environmental Protection Agency (EPA), through its ENERGY STAR{reg_sign} program, has been developing plant energy performance indicators (EPIs) to encourage a variety of U.S. industries to use energy more efficiently. This report describes work with the corn refining industry to provide a plant-level indicator of energy efficiency for facilities that produce a variety of products--including corn starch, corn oil, animal feed, corn sweeteners, and ethanol--for the paper, food, beverage, and other industries in the United States. Consideration is given to the role that performance-based indicators play in motivating change; the steps needed to develop indicators, including interacting with an industry to secure adequate data for an indicator; and the actual application and use of an indicator when complete. How indicators are employed in the EPA's efforts to encourage industries to voluntarily improve their use of energy is discussed as well. The report describes the data and statistical methods used to construct the EPI for corn refining plants. Individual equations are presented, as are the instructions for using them in an associated Excel spreadsheet.

Effects of a Modified German Volume Training Program on Muscular Hypertrophy and Strength.

Science.gov (United States)

Amirthalingam, Theban; Mavros, Yorgi; Wilson, Guy C; Clarke, Jillian L; Mitchell, Lachlan; Hackett, Daniel A

2017-11-01

Amirthalingam, T, Mavros, Y, Wilson, GC, Clarke, JL, Mitchell, L, and Hackett, DA. Effects of a modified German volume training program on muscular hypertrophy and strength. J Strength Cond Res 31(11): 3109-3119, 2017-German Volume Training (GVT), or the 10 sets method, has been used for decades by weightlifters to increase muscle mass. To date, no study has directly examined the training adaptations after GVT. The purpose of this study was to investigate the effect of a modified GVT intervention on muscular hypertrophy and strength. Nineteen healthy men were randomly assign to 6 weeks of 10 or 5 sets of 10 repetitions for specific compound resistance exercises included in a split routine performed 3 times per week. Total and regional lean body mass, muscle thickness, and muscle strength were measured before and after the training program. Across groups, there were significant increases in lean body mass measures, however, greater increases in trunk (p = 0.043; effect size [ES] = -0.21) and arm (p = 0.083; ES = -0.25) lean body mass favored the 5-SET group. No significant increases were found for leg lean body mass or measures of muscle thickness across groups. Significant increases were found across groups for muscular strength, with greater increases in the 5-SET group for bench press (p = 0.014; ES = -0.43) and lat pull-down (p = 0.003; ES = -0.54). It seems that the modified GVT program is no more effective than performing 5 sets per exercise for increasing muscle hypertrophy and strength. To maximize hypertrophic training effects, it is recommended that 4-6 sets per exercise be performed, as it seems gains will plateau beyond this set range and may even regress due to overtraining.

Production of Al-Ti-B grain refining master alloys from Na{sub 2}B{sub 4}O{sub 7} and K{sub 2}TiF{sub 6}

Energy Technology Data Exchange (ETDEWEB)

Birol, Yuecel [Materials Institute, Marmara Research Center, TUBITAK, Gebze, Kocaeli (Turkey)], E-mail: yucel.birol@mam.gov.tr

2008-06-30

It is very desirable to replace the KBF{sub 4} salt in the popular 'halide salt' process to reduce the volume of fluoride salts to be added to molten aluminium in the production of Al-Ti-B grain refiners. Being over 2 times richer in B, Na{sub 2}B{sub 4}O{sub 7} is a promising replacement for KBF{sub 4}, and is used in the present work to produce Al-Ti-B grain refiner master alloys. A fraction of the aluminide particles were entrapped in the spent salt giving a relatively lower Ti recovery when KBF{sub 4} was replaced by Na{sub 2}B{sub 4}O{sub 7}. The grain refining performance of the Al-Ti-B grain refiner alloy thus produced was nevertheless acceptable. The spent salt became too viscous with the oxides, aluminides and borides to be removed by decanting when Na{sub 2}B{sub 4}O{sub 7}.5H{sub 2}O was used to supply boron. The viscous spent salt, entrained in the grain refiner alloy, did not only impair its performance, but also hurt the fluidity of the molten alloy and made pouring difficult.

Refinement-Animation for Event-B - Towards a Method of Validation

DEFF Research Database (Denmark)

Hallerstede, Stefan; Leuschel, Michael; Plagge, Daniel

2010-01-01

We provide a detailed description of refinement in Event-B, both as a contribution in itself and as a foundation for the approach to simultaneous animation of multiple levels of refinement that we propose. We present an algorithm for simultaneous multi-level animation of refinement, and show how ...

Outlook for Canadian refining

International Nuclear Information System (INIS)

Boje, G.

1998-01-01

The petroleum supply and demand balance was discussed and a comparison between Canadian and U.S. refineries was provided. The impact of changing product specifications on the petroleum industry was also discussed. The major changes include sulphur reductions in gasoline, benzene and MMT additives. These changes have been made in an effort to satisfy environmental needs. Geographic margin variations in refineries between east and west were reviewed. An overview of findings from the Solomon Refining Study of Canadian and American refineries, which has been very complimentary of the Canadian refining industry, was provided. From this writer's point of view refinery utilization has improved but there is a threat from increasing efficiency of US competitors. Environmental issues will continue to impact upon the industry and while the chances for making economic returns on investment are good for the years ahead, it will be a challenge to maintain profitability

Oil refining in U.S. foreign-trade zones

International Nuclear Information System (INIS)

Powell, S.J.; Potter, T.J.

1991-01-01

With the crude-oil import supply being as inexpensive as it is today, relative to domestic supply, many independents have been sourcing their crude-oil needs from abroad and have found it an opportune time to step up their level of refining activity. To further enhance their competitive position with respect to foreign refineries, certain domestic refiners have discovered the operational benefits and savings that result from having a refinery designated as a foreign-trade zone (FTZ) under the Foreign-Trade Zones Act of 1934, as amended. This paper examines the history and use of foreign-trade subzones for refining activities

English-Chinese oil refining dictionary. [English-Chinese

Energy Technology Data Exchange (ETDEWEB)

Chou, P; Zing, Z [eds.

1979-01-01

The dictionary is a collection of many disciplines but specialized in the terminology related to petroleum refining. It contains terms in areas such as refining, factory equipment and installation, petroleum products and test analysis, and instrument automation. It also contains terms in areas of petrochemistry, oil storage and transport, computer technology, and environmental protection. The total number of terms collected was approximately 53,000.

Stirling Space Engine Program. Volume 2; Appendixes A, B, C and D

Science.gov (United States)

Dhar, Manmohan

1999-01-01

The objective of this program was to develop the technology necessary for operating Stirling power converters in a space environment and to demonstrate this technology in full-scale engine tests. Volume 2 of the report includes the following appendices: Appendix A: Heater Head Development (Starfish Heater Head Program, 1/10th Segment and Full-Scale Heat Pipes, and Sodium Filling and Processing); Appendix B: Component Test Power Converter (CTPC) Component Development (High-temperature Organic Materials, Heat Exchanger Fabrication, Beryllium Issues, Sodium Issues, Wear Couple Tests, Pressure Boundary Penetrations, Heating System Heaters, and Cooler Flow Test); Appendix C: Udimet Testing (Selection of the Reference Material for the Space Stirling Engine Heater Head, Udimet 720LI Creep Test Result Update, Final Summary of Space Stirling Endurance Engine Udimet 720L1 Fatigue Testing Results, Udimet 720l1 Weld Development Summary, and Udimet 720L1 Creep Test Final Results Summary), and Appendix D: CTPC Component Development Photos.

Design of Training Systems, Phase II Report, Volume III; Model Program Descriptions and Operating Procedures. TAEG Report No. 12-2.

Science.gov (United States)

Naval Training Equipment Center, Orlando, FL. Training Analysis and Evaluation Group.

The Design of Training Systems (DOTS) project was initiated by the Department of Defense (DOD) to develop tools for the effective management of military training organizations. Volume 3 contains the model and data base program descriptions and operating procedures designed for phase 2 of the project. Flow charts and program listings for the…

Contextual Distance Refining for Image Retrieval

KAUST Repository

Islam, Almasri

2014-01-01

Recently, a number of methods have been proposed to improve image retrieval accuracy by capturing context information. These methods try to compensate for the fact that a visually less similar image might be more relevant because it depicts the same object. We propose a new quick method for refining any pairwise distance metric, it works by iteratively discovering the object in the image from the most similar images, and then refine the distance metric accordingly. Test show that our technique improves over the state of art in terms of accuracy over the MPEG7 dataset.

Contextual Distance Refining for Image Retrieval

KAUST Repository

Islam, Almasri

2014-09-16

Recently, a number of methods have been proposed to improve image retrieval accuracy by capturing context information. These methods try to compensate for the fact that a visually less similar image might be more relevant because it depicts the same object. We propose a new quick method for refining any pairwise distance metric, it works by iteratively discovering the object in the image from the most similar images, and then refine the distance metric accordingly. Test show that our technique improves over the state of art in terms of accuracy over the MPEG7 dataset.

Singapore refiners in midst of huge construction campaign

International Nuclear Information System (INIS)

Land, R.

1992-01-01

This paper reports that Singapore's downstream capacity continues to mushroom. Singapore refiners, upbeat about long term prospects for petroleum products demand in the Asia-Pacific region, and are pressing plans to boost processing capacity. Their plans go beyond capacity expansions. They are proceeding with projects to upgrade refineries to emphasize production of higher value products and to further integrate refining capabilities wit the region's petrochemical industry. Planned expansion and upgrading projects at Singapore refineries call for outlays of more than $1 billion to boost total capacity to about 1.1 million b/d in 1993 and 1.27 million b/d by 1995. That would be the highest level since the mid-1980s, when refiners such as Shell Singapore cut capacity amid an oil glut. Singapore refineries currently are running at effective full capacity of 1.04 million b/d. Meanwhile, Singapore refiners are aggressively courting customers in the Indochina subcontinent, where long isolated centrally planned economies are turning gradually to free markets

Directions in refining and upgrading of heavy oil and bitumen

International Nuclear Information System (INIS)

Dawson, B.; Parker, R. J.; Flint, L.

1997-01-01

The expansion of heavy oil transportation, marketing and refining facilities over the past two decades have been reviewed to show the strides that several Canadian refiners have taken to build up the facilities required to process synthetic crude oil (SCO). Key points made at a conference, convened by the National Centre for Upgrading Technology (NCUT), held in Edmonton during September 1997 to discuss current and future directions in the refining and marketing of heavy oil, bitumen and SCO, were summarized. Among the key points mentioned were: (1) the high entry barriers faced by centralized upgraders, (2) the advantages of integrating SCO or heavy oil production with downstream refining, (3) the stiff competition from Venezuela and Mexico that both SCO and heavy oil will face in the U.S. PADD II market, (4) the differences between Canadian refiners who have profited from hydrocracking and are better able to handle coker-based SCO, and American refiners who rely chiefly on catalytic cracking and are less able to process the highly aromatic SCO, and (5) the disproportionate cost in the upgrading process represented by the conversion of asphaltenes. Challenges and opportunities for key stakeholders, i.e. producers, refiners, marketers and technology licensors also received much attention at the Edmonton conference

30 CFR 208.4 - Royalty oil sales to eligible refiners.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false Royalty oil sales to eligible refiners. 208.4... MANAGEMENT SALE OF FEDERAL ROYALTY OIL General Provisions § 208.4 Royalty oil sales to eligible refiners. (a... and defense. The Secretary will review these items and will determine whether eligible refiners have...

Development of an efficient grain refiner for Al-7Si alloy

Energy Technology Data Exchange (ETDEWEB)

Kori, S.A.; Murty, B.S.; Chakraborty, M. [Indian Inst. of Technol., Kharagpur (India). Dept. of Metall. and Mater. Eng.

2000-03-15

The response of Al-7Si alloy towards grain refinement by Al-Ti-B master alloys (with different Ti-B ratios) at different addition levels has been studied in detail. The results indicate that high B-containing master alloys are powerful grain refiners when compared to conventional grain refiners like Al-5Ti-lB master alloys. In the present study, indigenously developed master alloys have been used for the grain refinement of alloys Al-7Si and LM-25. Significant improvements in mechanical properties have been obtained with a combination of grain refiner and Sr as modifier. (orig.)

Local grid refinement for free-surface flow simulations

NARCIS (Netherlands)

van der Plas, Peter

2017-01-01

The principal goal of the current study is to explore and investigate the potential of local grid refinement for increasing the numerical efficiency of free-surface flow simulations in a practical context. In this thesis we propose a method for local grid refinement in the free-surface flow model

Oil refining in South Asia and Australasia

International Nuclear Information System (INIS)

Yamaguchi, N.D.

2000-01-01

An overview of the oil markets of Southeast Asia and Australasia is presented focussing on oil refining. Key statistics of both areas are tabulated, and figures providing information on GDP/capita, crude production, comparison of demand barrels, and product demand are provided. Crude oil production and supply, oil product demand, and the refining industries are examined with details given of evolution of capacity and cracking to distillation ratios

Investment in Exploration-Production and Refining - 2016

International Nuclear Information System (INIS)

Maisonnier, Guy; Hureau, Geoffroy; Serbutoviez, Sylvain; Silva, Constancio

2017-03-01

IFPEN analyses in this study the 2016 evolution of global investment in the field of exploration-production and refining: - Trends in oil and gas prices; - Investment in exploration/production: in sharp decline for the second consecutive year - the first time this has happened since 1986; - The global drilling market; - Geophysical: global activity and markets; - Offshore construction: market and business; - A significant reduction in refining projects (atmospheric distillation and conversion)

Refinement of Crystalline Boron and the Superconducting Properties of MgB2 by Attrition Ball Milling

International Nuclear Information System (INIS)

Lee, J. H.; Shin, S. Y.; Park, H. W.; Jun, B. H.; Kim, C. J.

2008-01-01

We report refinement of crystalline boron by an attrition ball milling system and the superconducting properties of the MgB 2 pellets prepared from the refined boron. In this work, we have conducted the ball milling with only crystalline boron powder, in order to improve homogeneity and control the grain size of the MgB 2 that is formed from it. We observed that the crystalline responses in the ball-milled boron became broader and weaker when the ball-milling time was further increased. On the other hand, the B 2 O 3 peak became stronger in the powders, resulting in an increase in the amount of MgO within the MgB 2 volume. The main reason for this is a greater oxygen uptake. From the perspective of the superconducting properties, however, the sample prepared from boron that was ball milled for 5 hours showed an improvement of critical current density (J c ), even with increased MgO phase, under an external magnetic field at 5 and 20 K.

Problems persist for French refining sector

International Nuclear Information System (INIS)

Beck, R.J.

1992-01-01

This paper reports that France's refiners face a continuing shortfall of middle distillate capacity and a persistent surplus of heavy fuel oil. That's the main conclusion of the official Hydrocarbon Directorate's report on how France's refining sector performed in 1991. Imports up---The directorate noted that although net production of refined products in French refineries rose to 1.534 million b/d in 1991 from 1.48 million b/d in 1990, products imports jumped 9.7% to 602,000 b/d in the period. The glut of heavy fuel oil eased to some extent last year because French nuclear power capacity, heavily dependent on ample water supplies, was crimped by drought. That spawned fuel switching. The most note worthy increase in imports was for motor diesel, climbing to 176,000 b/d from 148,000 b/d in 1990. Tax credits are spurring French consumption of that fuel. For the first time, consumption of motor diesel in 1991 outstripped that of gasoline at 374,000 b/d and 356,000 b/d respectively

Refining glass structure in two dimensions

Science.gov (United States)

Sadjadi, Mahdi; Bhattarai, Bishal; Drabold, D. A.; Thorpe, M. F.; Wilson, Mark

2017-11-01

Recently determined atomistic scale structures of near-two dimensional bilayers of vitreous silica (using scanning probe and electron microscopy) allow us to refine the experimentally determined coordinates to incorporate the known local chemistry more precisely. Further refinement is achieved by using classical potentials of varying complexity: one using harmonic potentials and the second employing an electrostatic description incorporating polarization effects. These are benchmarked against density functional calculations. Our main findings are that (a) there is a symmetry plane between the two disordered layers, a nice example of an emergent phenomena, (b) the layers are slightly tilted so that the Si-O-Si angle between the two layers is not 180∘ as originally thought but rather 175 ±2∘ , and (c) while interior areas that are not completely imagined can be reliably reconstructed, surface areas are more problematic. It is shown that small crystallites that appear are just as expected statistically in a continuous random network. This provides a good example of the value that can be added to disordered structures imaged at the atomic level by implementing computer refinement.

Application of discriminative models for interactive query refinement in video retrieval

Science.gov (United States)

Srivastava, Amit; Khanwalkar, Saurabh; Kumar, Anoop

2013-12-01

The ability to quickly search for large volumes of videos for specific actions or events can provide a dramatic new capability to intelligence agencies. Example-based queries from video are a form of content-based information retrieval (CBIR) where the objective is to retrieve clips from a video corpus, or stream, using a representative query sample to find more like this. Often, the accuracy of video retrieval is largely limited by the gap between the available video descriptors and the underlying query concept, and such exemplar queries return many irrelevant results with relevant ones. In this paper, we present an Interactive Query Refinement (IQR) system which acts as a powerful tool to leverage human feedback and allow intelligence analyst to iteratively refine search queries for improved precision in the retrieved results. In our approach to IQR, we leverage discriminative models that operate on high dimensional features derived from low-level video descriptors in an iterative framework. Our IQR model solicits relevance feedback on examples selected from the region of uncertainty and updates the discriminating boundary to produce a relevance ranked results list. We achieved 358% relative improvement in Mean Average Precision (MAP) over initial retrieval list at a rank cutoff of 100 over 4 iterations. We compare our discriminative IQR model approach to a naïve IQR and show our model-based approach yields 49% relative improvement over the no model naïve system.

Segmental Refinement: A Multigrid Technique for Data Locality

KAUST Repository

Adams, Mark F.; Brown, Jed; Knepley, Matt; Samtaney, Ravi

2016-01-01

We investigate a domain decomposed multigrid technique, termed segmental refinement, for solving general nonlinear elliptic boundary value problems. We extend the method first proposed in 1994 by analytically and experimentally investigating its complexity. We confirm that communication of traditional parallel multigrid is eliminated on fine grids, with modest amounts of extra work and storage, while maintaining the asymptotic exactness of full multigrid. We observe an accuracy dependence on the segmental refinement subdomain size, which was not considered in the original analysis. We present a communication complexity analysis that quantifies the communication costs ameliorated by segmental refinement and report performance results with up to 64K cores on a Cray XC30.

Segmental Refinement: A Multigrid Technique for Data Locality

KAUST Repository

Adams, Mark F.

2016-08-04

We investigate a domain decomposed multigrid technique, termed segmental refinement, for solving general nonlinear elliptic boundary value problems. We extend the method first proposed in 1994 by analytically and experimentally investigating its complexity. We confirm that communication of traditional parallel multigrid is eliminated on fine grids, with modest amounts of extra work and storage, while maintaining the asymptotic exactness of full multigrid. We observe an accuracy dependence on the segmental refinement subdomain size, which was not considered in the original analysis. We present a communication complexity analysis that quantifies the communication costs ameliorated by segmental refinement and report performance results with up to 64K cores on a Cray XC30.

HASSP and HEAVY: Tools for automated heavy atom searches and refinement

International Nuclear Information System (INIS)

Terwilliger, T.T.

1994-06-01

In this tutorial, a simple example using model data for one derivative with anomalous information will be used to demonstrate the use of HASSP and HEAVY in heavy atom determination and refinement. The data used here will actually be based on model MAD data that has been converted to MIR format using MADMRG, but the treatment is identical to that for any other SIR+anomalous data. The data nd most of the programs discussed here can be obtained by e-mail from ''terwil at sign prov2.lanl.gov'' along with VAX-specific command files to run the data through

Weapon container catalog. Volumes 1 & 2

Energy Technology Data Exchange (ETDEWEB)

Brown, L.A.; Higuera, M.C.

1998-02-01

The Weapon Container Catalog describes H-gear (shipping and storage containers, bomb hand trucks and the ancillary equipment required for loading) used for weapon programs and for special use containers. When completed, the catalog will contain five volumes. Volume 1 for enduring stockpile programs (B53, B61, B83, W62, W76, W78, W80, W84, W87, and W88) and Volume 2, Special Use Containers, are being released. The catalog is intended as a source of information for weapon program engineers and also provides historical information. The catalog also will be published on the SNL Internal Web and will undergo periodic updates.

Single Shell Tank (SST) Program Plan

International Nuclear Information System (INIS)

HAASS, C.C.

2000-01-01

This document provides an initial program plan for retrieval of the single-shell tank waste. Requirements, technical approach, schedule, organization, management, and cost and funding are discussed. The program plan will be refined and updated in fiscal year 2000

Single Shell Tank (SST) Program Plan

Energy Technology Data Exchange (ETDEWEB)

HAASS, C.C.

2000-03-21

This document provides an initial program plan for retrieval of the single-shell tank waste. Requirements, technical approach, schedule, organization, management, and cost and funding are discussed. The program plan will be refined and updated in fiscal year 2000.

Solving the Sophistication-Population Paradox of Game Refinement Theory

OpenAIRE

Xiong , Shuo; Tiwary , Parth ,; Iida , Hiroyuki

2016-01-01

Part 4: Short Papers; International audience; A mathematical model of game refinement was proposed based on uncertainty of game outcome. This model has been shown to be useful in measuring the entertainment element in the domains such as boardgames and sport games. However, game refinement theory has not been able to explain the correlation between the popularity of a game and the game refinement value. This paper introduces another aspect in the study of game entertainment, the concept of “a...

A refined approach: Saudi Arabia moves beyond crude

International Nuclear Information System (INIS)

Krane, Jim

2015-01-01

Saudi Arabia's role in global energy markets is changing. The kingdom is reshaping itself as a supplier of refined petroleum products while moving beyond its long-held role as a simple exporter of crude oil. This change is commensurate with the typical development trajectory of a state progressing to a more advanced stage of global economic integration. Gains from increased refining include reducing fuel imports and capturing margins now bequeathed to competitors. Refining also allows the kingdom to export its heavy crude oil to a wider array of customers, beyond select importers configured to handle heavy crudes. However, the move also presents strategic complications. The world's 'swing supplier' of oil may grow less willing or able to adjust supply to suit market demands. In the process, Saudi Arabia may have to update the old “oil for security” relationship that links it with Washington, augmenting it with a more diverse set of economic and investment ties with individual companies and countries, including China. -- Highlights: •Saudi Arabia is diverting crude oil into an expanding refining sector. •In doing so, the kingdom is moving beyond its role as global “swing supplier” of crude oil. •The kingdom will benefit from increased refining, including enhanced demand for heavy crude. •Strategic complications may force it to seek security partners beyond Washington

Bayesian ensemble refinement by replica simulations and reweighting

Science.gov (United States)

Hummer, Gerhard; Köfinger, Jürgen

2015-12-01

We describe different Bayesian ensemble refinement methods, examine their interrelation, and discuss their practical application. With ensemble refinement, the properties of dynamic and partially disordered (bio)molecular structures can be characterized by integrating a wide range of experimental data, including measurements of ensemble-averaged observables. We start from a Bayesian formulation in which the posterior is a functional that ranks different configuration space distributions. By maximizing this posterior, we derive an optimal Bayesian ensemble distribution. For discrete configurations, this optimal distribution is identical to that obtained by the maximum entropy "ensemble refinement of SAXS" (EROS) formulation. Bayesian replica ensemble refinement enhances the sampling of relevant configurations by imposing restraints on averages of observables in coupled replica molecular dynamics simulations. We show that the strength of the restraints should scale linearly with the number of replicas to ensure convergence to the optimal Bayesian result in the limit of infinitely many replicas. In the "Bayesian inference of ensembles" method, we combine the replica and EROS approaches to accelerate the convergence. An adaptive algorithm can be used to sample directly from the optimal ensemble, without replicas. We discuss the incorporation of single-molecule measurements and dynamic observables such as relaxation parameters. The theoretical analysis of different Bayesian ensemble refinement approaches provides a basis for practical applications and a starting point for further investigations.

The future of refining industry is in Asia

International Nuclear Information System (INIS)

Dupin, L.

2010-01-01

The decision of Total Group to close down the refining activity of its Flandres' site at Dunkerque (France) is a testimony of the deep restructuring that is affecting this sector. The migration of the refining activity towards Middle-East and Asia has started several years ago. The World capacities are increasing: in 2009 4.36 billion tons of petroleum products were refined in the world, representing a 1.9% rise with respect to 2008. 661 refineries exist in the world, among which 6 were inaugurated in 2009, 115 are located in Europe and 12 in France. The bad health of the European refining activity is beneficial to Middle and Asia where investments in new production capacities follow on from one another. From now to 2030, these areas will benefit from 70% of the worldwide investments compared to 11% only for Europe and North America. The decline of the European refining industry is directly linked to decay of the automotive fuel consumption and to the increase of the diesel fuel share with respect to gasoline. On the other hand, Asia, and in particular China and India, follow the exactly opposite trend thanks to their population and economic growths. Therefore, European oil companies try to invest in Asia and are looking for new production capacities in China and India. (J.S.)

Decontamination and decarburization of stainless and carbon steel by melt refining

International Nuclear Information System (INIS)

Mizia, R.E.; Worcester, S.A.; Twidwell, L.G.; Webber, D.; Paolini, D.J.; Weldon, T.A.

1996-01-01

With many nuclear reactors and facilities being decommissioned in the next ten to twenty years the concern for handling and storing Radioactive Scrap Metal (RSM) is growing. Upon direction of the DOE Office of Environmental Restoration and Waste Management, Lockheed Idaho Technology Company (LITCO) is developing technologies for the conditioning of spent fuels and high-level wastes for interim storage and repository acceptance, including the recycling of Radioactive Scrap Metals (RSM) for beneficial reuse with the DOE complex. In February 1993, Montana Tech of the University of Montana was contracted to develop and demonstrate technologies for the decontamination of stainless steel RSM. The general objectives of the Montana Tech research program included conducting a literature survey, performing laboratory scale melt refining experiments to optimize decontaminating slag compositions, performing an analysis of preferred melting techniques, coordinating pilot scale and commercial scale demonstrations, and producing sufficient quantities of surrogate-containing material for all of the laboratory, pilot and commercial scale test programs. Later on, the program was expanded to include decontamination of carbon steel RSM. Each research program has been completed, and results are presented in this report

Study on structural refinement and electrochemical behaviour of Ba0.5Sr0.5Co0.8Fe0.2O3-δ as cathode materials for intermediate temperature solid oxide fuel cells (IT-SOFC)

Science.gov (United States)

Kautkar, Pranay R.; Shirbhate, Shraddha C.; Acharya, Smita A.

2018-05-01

Ba0.5Sr0.5Co0.8Fe0.2O3-δ (BSCF) was prepared by ethylene glycol-citrate combined sol-gel combustion route and calcined at optimized temperature 1050°C. The X-ray Diffraction (XRD) data revealing the crystal purity of BSCF cathode was refined by the Cubic-type structure having the space group Pm-3m by Rietveld analysis. Refined lattice parameter of BSCF cathode is a = 3.9759 Å and unit cell volume is 62.85 (4) Å3, Co/Fe-O bond length from VESTA program figured out to be 1.987 (3) Å. Electron density distribution (EDD) of the unit cell of BSCF cathode shows the bonding feature with oxygen ions, this could represent oxygen vacancies are present in the lattice. These results reflected in electrochemical impedance spectra measurement of symmetric cell. Area of specific resistance (ASR) of the BSCF cathode was found to be 0.17 Ω.cm2 at 700°C and respective activation energy (Ea) 1.15 eV. It shows surface exchange at cathode interface, surface diffusion and self-diffusion happened through Ce0.85Sd0.15O1.95 (SDC15) electrolyte.

Regulatory Oversight Program, July 1, 1993--March 3, 1997. Volume 3

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-12-31

On July, 1993, a Regulatory Oversight (RO) organization was established within the US DOE, Oak Ridge Operations (ORO) to provide regulatory oversight of the DOE uranium enrichment facilities leased to the United States Enrichment Corporation (USEC). The purpose of the OR program was to ensure continued plant safety, safeguards and security while the plants were transitioned to regulatory oversight by the Nuclear Regulatory Commission (NRC). Volume 3 contains copies of two reports that document the DOE/ORO regulatory oversight inspection and enforcement history for each gaseous diffusion plant site. Each report provides a formal mechanism by which DOE/ORO could communicate the inspection and enforcement history to NRC. The reports encompass the inspection activities that occurred during July 1, 1993 through March 2, 1997.

Refining - Panorama 2008; Raffinage - Panorama 2008

Energy Technology Data Exchange (ETDEWEB)

NONE

2008-07-01

Investment rallied in 2007, and many distillation and conversion projects likely to reach the industrial stage were announced. With economic growth sustained in 2006 and still pronounced in 2007, oil demand remained strong - especially in emerging countries - and refining margins stayed high. Despite these favorable business conditions, tensions persisted in the refining sector, which has fallen far behind in terms of investing in refinery capacity. It will take renewed efforts over a long period to catch up. Looking at recent events that have affected the economy in many countries (e.g. the sub-prime crisis), prudence remains advisable.

Volume-change-free GeTeN films for high-performance phase-change memory

International Nuclear Information System (INIS)

Yin, You; Hosaka, Sumio; Zhang, Hui; Liu, Yang; Yu, Qi

2013-01-01

N-doping into GeTe is investigated with the aim of reducing the volume change upon crystallization, which usually induces a huge internal stress in phase-change memory devices. It is demonstrated that the thickness change upon crystallization of a N-doped GeTe (GeTeN) film is almost zero when N is doped in an appropriate amount. Cracks resulting from the stress caused by volume change disappear and the mean crystal size decreases by more than 50% upon N-doping into GeTe. It is thought that the volume-change-free behaviour is due to the formation of low-density nitride and grain refinement. (paper)

The Charfuel coal refining process

International Nuclear Information System (INIS)

Meyer, L.G.

1991-01-01

The patented Charfuel coal refining process employs fluidized hydrocracking to produce char and liquid products from virtually all types of volatile-containing coals, including low rank coal and lignite. It is not gasification or liquefaction which require the addition of expensive oxygen or hydrogen or the use of extreme heat or pressure. It is not the German pyrolysis process that merely 'cooks' the coal, producing coke and tar-like liquids. Rather, the Charfuel coal refining process involves thermal hydrocracking which results in the rearrangement of hydrogen within the coal molecule to produce a slate of co-products. In the Charfuel process, pulverized coal is rapidly heated in a reducing atmosphere in the presence of internally generated process hydrogen. This hydrogen rearrangement allows refinement of various ranks of coals to produce a pipeline transportable, slurry-type, environmentally clean boiler fuel and a slate of value-added traditional fuel and chemical feedstock co-products. Using coal and oxygen as the only feedstocks, the Charfuel hydrocracking technology economically removes much of the fuel nitrogen, sulfur, and potential air toxics (such as chlorine, mercury, beryllium, etc.) from the coal, resulting in a high heating value, clean burning fuel which can increase power plant efficiency while reducing operating costs. The paper describes the process, its thermal efficiency, its use in power plants, its pipeline transport, co-products, environmental and energy benefits, and economics

Accuracy of the all patient refined diagnosis related groups classification system in congenital heart surgery.

Science.gov (United States)

Parnell, Aimee S; Shults, Justine; Gaynor, J William; Leonard, Mary B; Dai, Dingwei; Feudtner, Chris

2014-02-01

Administrative data are increasingly used to evaluate clinical outcomes and quality of care in pediatric congenital heart surgery (CHS) programs. Several published analyses of large pediatric administrative data sets have relied on the All Patient Refined Diagnosis Related Groups (APR-DRG, version 24) diagnostic classification system. The accuracy of this classification system for patients undergoing CHS is unclear. We performed a retrospective cohort study of all 14,098 patients 0 to 5 years of age undergoing any of six selected congenital heart operations, ranging in complexity from isolated closure of a ventricular septal defect to single-ventricle palliation, at 40 tertiary-care pediatric centers in the Pediatric Health Information Systems database between 2007 and 2010. Assigned APR-DRGs (cardiac versus noncardiac) were compared using χ2 or Fisher's exact tests between those patients admitted during the first day of life versus later and between those receiving extracorporeal membrane oxygenation support versus those not. Recursive partitioning was used to assess the greatest determinants of APR-DRG type in the model. Every patient admitted on day 1 of life was assigned to a noncardiac APR-DRG (pDRG (pDRG experienced a significantly increased mortality (pDRG coding has systematic misclassifications, which may result in inaccurate reporting of CHS case volumes and mortality. Copyright © 2014 The Society of Thoracic Surgeons. Published by Elsevier Inc. All rights reserved.

Clean Coal Technology Programs: Program Update 2003 (Volume 1)

Energy Technology Data Exchange (ETDEWEB)

Assistant Secretary for Fossil Energy

2003-12-01

Annual report on the Clean Coal Technology Demonstration Program (CCTDP), Power Plant Improvement Initiative (PPII), and Clean Coal Power Initiative (CCPI). The report addresses the roles of the programs, implementation, funding and costs, project descriptions, legislative history, program history, environmental aspects, and project contacts. The project descriptions describe the technology and provides a brief summary of the demonstration results.

User's guide for PRISM (Plant Risk Status Information Management System) Arkansas Nuclear One-Unit 1: Volume 1, Program for inspectors

International Nuclear Information System (INIS)

Campbell, D.J.; Guthrie, V.H.; Kirchner, J.R.; Kirkman, J.Q.; Paula, H.M.; Ellison, B.C.; Dycus, F.M.; Farquharson, J.A.; Flanagan, G.F.

1988-03-01

This user's guide is a two-volume document designed to teach NRC inspectors and NRC regulators how to access probabilistic risk assessment information from the two Plant Risk Status Information Management System (PRISIM) programs developed for Arkansas Nuclear One -- Unit One (ANO-1). This document, Volume 1, describes how the PRA information available in Version 1.0 of PRISIM is useful for planning inspections. Using PRISIM, inspectors can quickly access PRA information and use that information to update risk analysis results, reflecting a plant's status at any particular time. Both volumes are stand-alone documents, and each volume presents several sample computer sessions designed to lead the user through a variety of PRISIM applications used to obtain PRA-related information for monitoring and controlling plant risk

Asian oil refining. Demand growth and deregulation - an uncertain future

International Nuclear Information System (INIS)

Sameer Nawaz.

1996-01-01

The objective of the report is to identify the most important features of the oil refining industry in Asia. Major developments in consumption patterns changes in regional importance of countries are discussed, highlighting potential future developments. The first chapter introduces the various refining processes and presents a simple model for the analysis of complex refineries. Chapter 2 examines the development of the Asian refining industry against a background of economic growth and analyses trends in consumption of all products in Asian countries. In Chapter 3, the key issues concerning the refining industry are examined, among them the forces driving consumption, including the importance of economic development, and electricity and transport demand. The importance of product imports and international trade is discussed, and the extent of government involvement and the effects of changing retail and market prices are analysed. Chapter 4 looks at the strategies that oil and gas companies are following in the Asian refining industry. Particular significance is attached to the vertical integration of the oil majors, Japanese and Middle Eastern oil companies. A brief overview of the importance of the petrochemical industry is presented. The countries of Asia that are involved in the refining industry are profiled in Chapter 5. The future trend in oil consumption is examined in Chapter 6. There follows a brief discussion of the plans to expand crude refining capacity in the various countries and a forecast of the state of overcapacity which will result. In the final chapter, brief profiles of some of the most important companies in the Asian refining industry are presented, discussing their major activities and future plans. (Author)

Connected Vehicle Pilot Deployment Program Independent Evaluation: Mobility, Environmental, and Public Agency Efficiency Refined Evaluation Plan - New York City

Science.gov (United States)

2018-03-01

The purpose of this report is to provide a refined evaluation plan detailing the approach to be used by the Texas A&M Transportation Institute Connected Vehicle Pilot Deployment Evaluation Team for evaluating the mobility, environmental, and public a...

Grain refinement of permanent mold cast copper base alloys. Final report

Energy Technology Data Exchange (ETDEWEB)

Sadayappan, M.; Thomson, J. P.; Elboujdaini, M.; Gu, G. Ping; Sahoo, M.

2004-04-29

Grain refinement behavior of copper alloys cast in permanent molds was investigated. This is one of the least studied subjects in copper alloy castings. Grain refinement is not widely practiced for leaded copper alloys cast in sand molds. Aluminum bronzes and high strength yellow brasses, cast in sand and permanent molds, were usually fine grained due to the presence of more than 2% iron. Grain refinement of the most common permanent mold casting alloys, leaded yellow brass and its lead-free replacement EnviroBrass III, is not universally accepted due to the perceived problem of hard spots in finished castings and for the same reason these alloys contain very low amounts of iron. The yellow brasses and Cu-Si alloys are gaining popularity in North America due to their low lead content and amenability for permanent mold casting. These alloys are prone to hot tearing in permanent mold casting. Grain refinement is one of the solutions for reducing this problem. However, to use this technique it is necessary to understand the mechanism of grain refinement and other issues involved in the process. The following issues were studied during this three year project funded by the US Department of Energy and the copper casting industry: (1) Effect of alloying additions on the grain size of Cu-Zn alloys and their interaction with grain refiners; (2) Effect of two grain refining elements, boron and zirconium, on the grain size of four copper alloys, yellow brass, EnviroBrass II, silicon brass and silicon bronze and the duration of their effect (fading); (3) Prediction of grain refinement using cooling curve analysis and use of this method as an on-line quality control tool; (4) Hard spot formation in yellow brass and EnviroBrass due to grain refinement; (5) Corrosion resistance of the grain refined alloys; (6) Transfer the technology to permanent mold casting foundries; It was found that alloying elements such as tin and zinc do not change the grain size of Cu-Zn alloys

The present state of refining in France

International Nuclear Information System (INIS)

1996-01-01

The european refining industry suffers from a production over-capacity and closures are inevitable; the situation is even worse in France due to the imbalance between gas oil and gasoline prices and the weak margin for distributors. The French refining industry is however an important and essential link for its strategic fuel and petroleum product supply, and represent 17000 jobs. Several measures are introduced by the French Industry department towards restructuring, capacity reduction and fuel price harmonization

A new process of electron beam refining of niobium

International Nuclear Information System (INIS)

Pinatti, D.G.

1981-01-01

A review of thermodynamic equilibrium, the kinetic theory and experimental results of the metal-gas interaction in refractory metals is presented. N 2 , H 2 and CO absorption and desorption take place by a reversible process while O 2 takes place by a irreversible process with atom absorption and metal oxide desorption. A new technology of electron beam refining of Niobium is proposed based on four points: 1) preparation of the aluminothermic reduced electrode, 2) zone refining in the first melt, 3) kinetic theory of refining in the following melts and 4) design of a compact furnace. Experimental results in a pilot plant of 300 KW have shown complete agreement with the proposed technology yielding a productivity 2.4 times larger than the value predicted by the conventional technology of electron beam refining of Niobium. (Author) [pt

Energy Extension Service Pilot Program: evaluation report after two years. Volume I. Evaluation summary

Energy Technology Data Exchange (ETDEWEB)

None

1980-04-01

The EES pilot program was initiated in August 1977, when 10 states were selected on a competitive basis for participation. The pilot states (Alabama, Connecticut, Michigan, New Mexico, Pennsylvania, Tennessee, Texas, Washington, Wisconsin, and Wyoming) devoted the first 6 months to start-up activities. This document is a follow-up report to the three volume Evaluation Summary of the first year of the pilot EES program published in September 1979. The purpose of this report is to provide an overview of the impacts and costs of the two years of the pilot program, and to check the consistency of findings over the two year period. The analysis addresses the following: (1) were the impact findings of Year I and Year II consistent, or did Year I and Year II attitudes and behavior vary. If variation existed, could it be attributed to program changes as the EES progressed from a start-up phase (Year I) to more normal service delivery (Year II); and (2) did costs of service delivery change (again reflecting start-up and normal service delivery costs). Did cost changes affect conclusions about the relative cost effectiveness of delivering services to different target audiences.

European refining: evolution or revolution?

International Nuclear Information System (INIS)

Cuthbert, N.

1999-01-01

A recent detailed analysis of the refining business in Europe (by Purvin and Gurtz) was used to highlight some key issues facing the industry. The article was written under five sub-sections: (i) economic environment (assessment of the economic prospects for Europe), (ii) energy efficiency and global warming (lists the four points of the EU car makers' voluntary agreement), (iii) fuel quality and refinery investment (iv) refinery capacity and utilisation and (v) industry structure and development. Diagrams show GDP per capita for East and West, European road fuel demand to 2015 and European net trade and European refinery ownership by crude capacity. It was concluded that the future of refining in Europe is 'exciting and challenging' and there are likely to be more large joint venture refineries. (UK)

Cosmos++: relativistic magnetohydrodynamics on unstructured grids with local adaptive refinement

International Nuclear Information System (INIS)

Salmonson, Jay D; Anninos, Peter; Fragile, P Chris; Camarda, Karen

2007-01-01

A code and methodology are introduced for solving the fully general relativistic magnetohydrodynamic (GRMHD) equations using time-explicit, finite-volume discretization. The code has options for solving the GRMHD equations using traditional artificial-viscosity (AV) or non-oscillatory central difference (NOCD) methods, or a new extended AV (eAV) scheme using artificial-viscosity together with a dual energy-flux-conserving formulation. The dual energy approach allows for accurate modeling of highly relativistic flows at boost factors well beyond what has been achieved to date by standard artificial viscosity methods. It provides the benefit of Godunov methods in capturing high Lorentz boosted flows but without complicated Riemann solvers, and the advantages of traditional artificial viscosity methods in their speed and flexibility. Additionally, the GRMHD equations are solved on an unstructured grid that supports local adaptive mesh refinement using a fully threaded oct-tree (in three dimensions) network to traverse the grid hierarchy across levels and immediate neighbors. Some recent studies will be summarized

Recovery Act: Finite Volume Based Computer Program for Ground Source Heat Pump Systems

Energy Technology Data Exchange (ETDEWEB)

James A Menart, Professor

2013-02-22

This report is a compilation of the work that has been done on the grant DE-EE0002805 entitled Finite Volume Based Computer Program for Ground Source Heat Pump Systems. The goal of this project was to develop a detailed computer simulation tool for GSHP (ground source heat pump) heating and cooling systems. Two such tools were developed as part of this DOE (Department of Energy) grant; the first is a two-dimensional computer program called GEO2D and the second is a three-dimensional computer program called GEO3D. Both of these simulation tools provide an extensive array of results to the user. A unique aspect of both these simulation tools is the complete temperature profile information calculated and presented. Complete temperature profiles throughout the ground, casing, tube wall, and fluid are provided as a function of time. The fluid temperatures from and to the heat pump, as a function of time, are also provided. In addition to temperature information, detailed heat rate information at several locations as a function of time is determined. Heat rates between the heat pump and the building indoor environment, between the working fluid and the heat pump, and between the working fluid and the ground are computed. The heat rates between the ground and the working fluid are calculated as a function time and position along the ground loop. The heating and cooling loads of the building being fitted with a GSHP are determined with the computer program developed by DOE called ENERGYPLUS. Lastly COP (coefficient of performance) results as a function of time are provided. Both the two-dimensional and three-dimensional computer programs developed as part of this work are based upon a detailed finite volume solution of the energy equation for the ground and ground loop. Real heat pump characteristics are entered into the program and used to model the heat pump performance. Thus these computer tools simulate the coupled performance of the ground loop and the heat pump. The

Multilevel local refinement and multigrid methods for 3-D turbulent flow

Energy Technology Data Exchange (ETDEWEB)

Liao, C.; Liu, C. [UCD, Denver, CO (United States); Sung, C.H.; Huang, T.T. [David Taylor Model Basin, Bethesda, MD (United States)

1996-12-31

A numerical approach based on multigrid, multilevel local refinement, and preconditioning methods for solving incompressible Reynolds-averaged Navier-Stokes equations is presented. 3-D turbulent flow around an underwater vehicle is computed. 3 multigrid levels and 2 local refinement grid levels are used. The global grid is 24 x 8 x 12. The first patch is 40 x 16 x 20 and the second patch is 72 x 32 x 36. 4th order artificial dissipation are used for numerical stability. The conservative artificial compressibility method are used for further improvement of convergence. To improve the accuracy of coarse/fine grid interface of local refinement, flux interpolation method for refined grid boundary is used. The numerical results are in good agreement with experimental data. The local refinement can improve the prediction accuracy significantly. The flux interpolation method for local refinement can keep conservation for a composite grid, therefore further modify the prediction accuracy.

Uranium refining process using ion exchange membrane

International Nuclear Information System (INIS)

Yamaguchi, Akira

1977-01-01

As for the method of refining uranium ore being carried out in Europe and America at present, uranium ore is roughly refined at the mine sites to yellow cake, then this is transported to refineries and refined by dry method. This method has the following faults, namely the number of processes is large, it requires expensive corrosion-resistant materials because of high temperature treatment, and the impurities in uranium tend to increase. On the other hand, in case of EXCER method, treatment is carried out at low temperature, and high purity uranium can be obtained, but the efficiency of electrolytic reduction process is extremely low, and economically infeasible. In the wet refining method called PNC process, uranium tetrafluoride is produced from uranium ore without making yellow cake, therefore the process is rationalized largely, and highly economical. The electrolytic reduction process in this method was developed by Asahi Chemical Industry Co., Ltd. by constructing the pilot plant in Ningyotoge Mine. The ion exchange membrane, the electrodes, and the problems concerning the process and the engineering for commercial plants were investigated. The electrolytic reduction process, the pilot plant, the development of the elements of electrolytic cells, the establishment of analytical process, the measurement of the electrolytic characteristics, the demonstration operation, and the life time of the electrolytic diaphragm are reported. (Kako, I.)

Ocean Thermal Energy Converstion (OTEC) test facilities study program. Final report. Volume II. Part B

Energy Technology Data Exchange (ETDEWEB)

None

1977-01-17

Results are presented of an 8-month study to develop alternative non-site-specific OTEC facilities/platform requirements for an integrated OTEC test program which may include land and floating test facilities. Volume II--Appendixes is bound in three parts (A, B, and C) which together comprise a compendium of the most significant detailed data developed during the study. Part B provides an annotated test list and describes component tests and system tests.

The Harwell TAILS computer program user's manual

International Nuclear Information System (INIS)

Rouse, K.D.; Cooper, M.J.

1980-11-01

The Harwell TAILS computer program is a versatile program for crystal structure refinement through the analysis of neutron or X-ray diffraction data from single crystals or powders. The main features of the program are described and details are given of the data input and output specifications. (author)

Adaptive mesh refinement for storm surge

KAUST Repository

Mandli, Kyle T.; Dawson, Clint N.

2014-01-01

An approach to utilizing adaptive mesh refinement algorithms for storm surge modeling is proposed. Currently numerical models exist that can resolve the details of coastal regions but are often too costly to be run in an ensemble forecasting framework without significant computing resources. The application of adaptive mesh refinement algorithms substantially lowers the computational cost of a storm surge model run while retaining much of the desired coastal resolution. The approach presented is implemented in the GeoClaw framework and compared to ADCIRC for Hurricane Ike along with observed tide gauge data and the computational cost of each model run. © 2014 Elsevier Ltd.

Adaptive mesh refinement for storm surge

KAUST Repository

Mandli, Kyle T.

2014-03-01

An approach to utilizing adaptive mesh refinement algorithms for storm surge modeling is proposed. Currently numerical models exist that can resolve the details of coastal regions but are often too costly to be run in an ensemble forecasting framework without significant computing resources. The application of adaptive mesh refinement algorithms substantially lowers the computational cost of a storm surge model run while retaining much of the desired coastal resolution. The approach presented is implemented in the GeoClaw framework and compared to ADCIRC for Hurricane Ike along with observed tide gauge data and the computational cost of each model run. © 2014 Elsevier Ltd.

Russian refining - an industry in transition

Energy Technology Data Exchange (ETDEWEB)

Barrett, E [CentreInvest, Moscow (Russian Federation)

1999-02-01

In the old Soviet Union (now called the CIS), the refining industry is undergoing much modernisation, although the process is far from complete. Eventually, the CIS is expected to have a market-responsive competitive refining business. The expected transformation is discussed according to a five-stage plan. The stages are (i) the change from horizontally integrated entity to vertically integrated global concerns, (ii) the change from over-manned dinosaurs to modern efficient businesses, (iii) the move towards smaller, more advanced market-orientated processes, (iv) improving the transport and storage infrastructures and (v) improving accountability and profitability. The predictions for 2005 onwards are for sustained profitability. (UK)

Variability-Specific Abstraction Refinement for Family-Based Model Checking

DEFF Research Database (Denmark)

Dimovski, Aleksandar; Wasowski, Andrzej

2017-01-01

and property, while the number of possible scenarios is very large. In this work, we present an automatic iterative abstraction refinement procedure for family-based model checking. We use Craig interpolation to refine abstract variational models based on the obtained spurious counterexamples (traces...

Zone refining of sintered, microwave-derived YBCO superconductors

International Nuclear Information System (INIS)

Warrier, K.G.K.; Varma, H.K.; Mani, T.V.; Damodaran, A.D.; Balachandran, U.

1993-07-01

Post-sintering treatments such as zone melting under thermal gradient has been conducted on sintered YBCO tape cast films. YBCO precursor powder was derived through decomposition of a mixture of nitrates of cations in a microwave oven for ∼4 min. The resulting powder was characterized and made into thin sheets by tape casting and then sintered at 945 C for 5 h. The sintered tapes were subjected to repeated zone refining operations at relatively high speeds of ∼30 mm/h. A microstructure having uniformly oriented grains in the a-b plane throughout the bulk of the sample was obtained by three repeated zone refining operations. Details of precursor preparation, microwave processing and its advantages, zone refining conditions, and microstructural features are presented in this paper

Report to Congress on the feasibility of establishing a heating oil component to the Strategic Petroleum Reserve. Volume 2: Appendices

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-06-01

Nine appendices to the main report are included in this volume. They are: Northeastern US distillate supply systems; New England fuel oil storage capacities and inventories; Characteristics of the northeast natural gas market; Documentation of statistical models and calculation of benefits; Regional product reserve study; Other countries` experience with refined product storage; Global refining supply demand appraisal; Summary of federal authorities relevant to the establishment of petroleum product reserves; Product stability and turnover requirements.

Site Environmental Report for 1999 - Volume 1

Energy Technology Data Exchange (ETDEWEB)

Ruggieri, M

2000-08-12

Each year, Ernest Orlando Lawrence Berkeley National Laboratory prepares an integrated report on its environmental programs to satisfy the requirements of United States Department of Energy Order 231.1. The Site Environmental Report for 1999 is intended to summarize Berkeley Lab's compliance with environmental standards and requirements, characterize environmental management efforts through surveillance and monitoring activities, and highlight significant programs and efforts for calendar year 1999. The report is separated into two volumes. Volume I contains a general overview of the Laboratory, the status of environmental programs, and summary results from surveillance and monitoring activities. Each chapter in Volume I begins with an outline of the sections that follow, including any tables or figures found in the chapter. Readers should use section numbers (e.g., {section}1.5) as navigational tools to find topics of interest in either the printed or the electronic version of the report. Volume II contains the individual data results from monitoring programs.

New 2D adaptive mesh refinement algorithm based on conservative finite-differences with staggered grid

Science.gov (United States)

Gerya, T.; Duretz, T.; May, D. A.

2012-04-01

We present new 2D adaptive mesh refinement (AMR) algorithm based on stress-conservative finite-differences formulated for non-uniform rectangular staggered grid. The refinement approach is based on a repetitive cell splitting organized via a quad-tree construction (every parent cell is split into 4 daughter cells of equal size). Irrespective of the level of resolution every cell has 5 staggered nodes (2 horizontal velocities, 2 vertical velocities and 1 pressure) for which respective governing equations, boundary conditions and interpolation equations are formulated. The connectivity of the grid is achieved via cross-indexing of grid cells and basic nodal points located in their corners: four corner nodes are indexed for every cell and up to 4 surrounding cells are indexed for every node. The accuracy of the approach depends critically on the formulation of the stencil used at the "hanging" velocity nodes located at the boundaries between different levels of resolution. Most accurate results are obtained for the scheme based on the volume flux balance across the resolution boundary combined with stress-based interpolation of velocity orthogonal to the boundary. We tested this new approach with a number of 2D variable viscosity analytical solutions. Our tests demonstrate that the adaptive staggered grid formulation has convergence properties similar to those obtained in case of a standard, non-adaptive staggered grid formulation. This convergence is also achieved when resolution boundary crosses sharp viscosity contrast interfaces. The convergence rates measured are found to be insensitive to scenarios when the transition in grid resolution crosses sharp viscosity contrast interfaces. We compared various grid refinement strategies based on distribution of different field variables such as viscosity, density and velocity. According to these tests the refinement allows for significant (0.5-1 order of magnitude) increase in the computational accuracy at the same

Quantitative analysis of retained austenite in laser melted martensitic stainless steel

CSIR Research Space (South Africa)

Seleka, T

2007-11-01

Full Text Available of this study was to determine if X-ray diffraction (XRD) was sufficient for quantifying the volume percentage of retained austenite. After a preliminary qualitative analysis, a Rietveld full pattern refinement program was used to quantify the volume percentage...

Environmental Restoration Program pollution prevention performance measures for FY 1993 and 1994 remedial investigations

International Nuclear Information System (INIS)

1993-03-01

The Martin Marietta Energy Systems, Inc., Environmental Restoration (ER) Program adopted a Pollution Prevention Program in March 1991. The program's mission is to minimize waste and prevent pollution in remedial investigations (RI), feasibility studies (FS), decontamination and decommissioning (D ampersand D), and surveillance and maintenance (S ampersand M) site program activities. Mission success will result in volume and/or toxicity reduction of generated waste. Energy Systems is producing a fully developed a Numerical Scoring System (NSS) and actually scoring the generators of Investigation Derived Waste (IDW) at six ER sites: Oak Ridge National Laboratory (ORNL), the Oak Ridge Y-12 Plant, the Oak Ridge K-25 site, Paducah Gaseous Diffusion Plant (Paducah), and Portsmouth Uranium Enrichment Complex (Portsmouth). This report summarizes the findings of this initial numerical scoring evaluation and shows where improvements in the overall ER Pollution prevention program may be required. This report identifies a number of recommendations that, if implemented, would help to improve site-performance measures. The continued development of the NSS will support generators in maximizing their Pollution Prevention/Waste Minimization efforts. Further refinements of the NSS, as applicable suggest comments and/or recommendations for improvement

Oil refining and product marketing developments in southeast Asia

International Nuclear Information System (INIS)

Szabo, A.M.

1992-01-01

Views on the future are based on supplies from a relatively stable Middle East and continued economic growth in the southeast Asian and Pacific countries. Under these circumstances the oil market for the Association of Southeast Asian Nations (ASEAN) will expand considerably during the decade of the 90's. Pacific country demand, 5.92 MMB/D, in 1990 is likely to grow to 7.06 MMB/D in 2000. Regional production could supply about 40% of this. The Asia-Pacific shortage of refining capacity could lead to high regional refined product prices and health refining profit margins. (author)

Electromyogram refinement using muscle synergy based regulation of uncertain information.

Science.gov (United States)

Min, Kyuengbo; Shin, Duk; Lee, Jongho; Kakei, Shinji

2018-04-27

Electromyogram signal (EMG) measurement frequently experiences uncertainty attributed to issues caused by technical constraints such as cross talk and maximum voluntary contraction. Due to these problems, individual EMGs exhibit uncertainty in representing their corresponding muscle activations. To regulate this uncertainty, we proposed an EMG refinement, which refines EMGs with regulating the contribution redundancy of the signals from EMGs to approximating torques through EMG-driven torque estimation (EDTE) using the muscular skeletal forward dynamic model. To regulate this redundancy, we must consider the synergistic contribution redundancy of muscles, including "unmeasured" muscles, to approximating torques, which primarily causes redundancy of EDTE. To suppress this redundancy, we used the concept of muscle synergy, which is a key concept of analyzing the neurophysiological regulation of contribution redundancy of muscles to exerting torques. Based on this concept, we designed a muscle-synergy-based EDTE as a framework for EMG refinement, which regulates the abovementioned uncertainty of individual EMGs in consideration of unmeasured muscles. In achieving the proposed EMG refinement, the most considerable point is to suppress a large change such as overestimation attributed to enhancement of the contribution of particular muscles to estimating torques. Therefore it is reasonable to refine EMGs by minimizing the change in EMGs. To evaluate this model, we used a Bland-Altman plot, which quantitatively evaluates the proportional bias of refined signals to EMGs. Through this evaluation, we showed that the proposed EDTE minimizes the bias while approximating torques. Therefore this minimization optimally regulates the uncertainty of EMGs and thereby leads to optimal EMG refinement. Copyright © 2018 Elsevier Ltd. All rights reserved.

Directory of Certificates of Compliance for Radioactive Materials Packages. Summary Report of NRC Approved Quality Assurance Programs for Radioactive Material Packages. Volume 3. Revision 5

International Nuclear Information System (INIS)

1985-10-01

This directory contains a Summary Report of the US Nuclear Regulatory Commission's Approved Packages (Volume I), all Certificates of Compliance (Volume 2), and Summary Report of NRC Approved Quality Assurance Programs (Volume 3) for Radioactive Material Packages effective October 1, 1985. The purpose of this directory is to make available a convenient source of information on packagings which have been approved by the US Nuclear Regulatory Commission. To assist in identifying packaging, an index by Model Number and corresponding Certificate of Compliance Number is included at the back of Volumes 1 and 2 of the directory. A listing by packaging types is included in the back of Volume 2. An alphabetical listing by Company name is included in the back of Volume 3 for approved QA programs. The Summary Reports include a listing of all users of each package design and approved QA programs prior to the publication date of the directory. Shipments of radioactive material utilizing these packages must be in accordance with the provisions of 49 CFR Section 173.471 and 10 CFR Part 71, as applicable. In satisfying the requirements of Section 71.12, it is the responsibility of the licensees to insure themselves that they have a copy of the current approval and conduct their transportation activities in accordance with a Nuclear Regulatory Commission approved quality assurance program. Copies of the current approval may be obtained from the US Nuclear Regulatory Commission Public Document Room files (see Docket No. listed on each certificate) at 1717 H Street, Washington, DC 20555. Note that the general license of 10 CFR Section 71.12 does not authorize the receipt, possession, use or transfer of byproduct, source or special nuclear material; such authorization must be obtained pursuant to 10 CFR Parts 30 to 36, 40, or 70

Decontamination of transuranic contaminated metals by melt refining

International Nuclear Information System (INIS)

Heshmatpour, B.; Copeland, G.L.; Heestand, R.L.

1983-01-01

Melt refining of transuranic contaminated metals is a possible decontamination process with the potential advantages of producing metal for reuse and of simplifying chemical analyses. By routinely achieving the 10 nCi/g( about0.1ppm) level by melt refining, scrap metal can be removed from the transuranic waste category. (To demonstrate the effectiveness of this melt refining process, mild steel, stainless steel, nickel, and copper were contaminated with 500 ppm (μg/g) PuO 2 and melted with various fluxes. The solidified slags and metals were analyzed for their plutonium contents, and corresponding partition ratios for plutonium were calculated. Some metals were double refined in order to study the effect of secondary slag treatment. The initial weight of the slags was also varied to investigate the effect of slag weight on the degree of plutonium removal. In general, all four metals could be decontaminated below 1 ppm (μg/g) Pu ( about100 nCi/g) by a single slag treatment. Doubling the slag weight did not improve decontamination significantly; however, double slag treatment using 5 wt.% slag did decontaminate the metals to below 0.1 ppm (μg/g) Pu (10 nCi/g).)

Role of manganese on the grain refining efficiency of AZ91D magnesium alloy refined by Al4C3

International Nuclear Information System (INIS)

Liu Shengfa; Zhang Yuan; Han Hui

2010-01-01

A novel Mg-50% Al 4 C 3 (hereafter in wt.%) master alloy has been developed by powder in situ synthesis process, the role of manganese on the grain refining efficiency of AZ91D magnesium alloy refined by this master alloy has been investigated. X-ray diffraction (XRD) and energy dispersive X-ray spectroscopy (EDS) results show the existence of Al 4 C 3 particles in this master alloy. After addition of 0.6% Al 4 C 3 or combined addition of 0.6% Al 4 C 3 and 0.27% Mn, the average grain size of AZ91D decreased dramatically from 360 μm to 210 μm, and from 360 μm to130 μm, respectively. However, no further refinement of grain size was achieved with additional amount of Mn exceeding 0.27% for AZ91D alloy refined by 0.6% Al 4 C 3 in the present investigation. Al-C-O-Mn-Fe-rich intermetallic particles with an Al-C-O-rich coating film, often observed in the central region of magnesium grains of the AZ91D alloy treated by the combination of Al 4 C 3 and Mn, are proposed to be the potent nucleating substrates for primary α-Mg.

40 CFR 80.555 - What provisions are available to a large refiner that acquires a small refiner or one or more of...

Science.gov (United States)

2010-07-01

... FUELS AND FUEL ADDITIVES Motor Vehicle Diesel Fuel; Nonroad, Locomotive, and Marine Diesel Fuel; and ECA... May 31, 2010 for a refinery acquired from a motor vehicle diesel fuel small refiner or beyond the... motor vehicle diesel fuel small refiner or beyond the dates specified in § 80.554(a) or (b), as...

Chromatography Analysis of Jatropha Curcas L Oil Raw and Refined

International Nuclear Information System (INIS)

Chitue de Assuncao Nascimento, Juliano; Lafargue Perez, Francisco; Diaz Velazquez, Manuel

2013-01-01

The chromatography of gases is one of the most versatile methods utilized in the chemical laboratory, which permits the determinations of the percentages and types of fatty acids present in vegetable oils. The objective of this work was to carry out a comparative study of the composition of the fatty acids, of the mechanically extracted oil from the seed of the Jatropha curcas L plant in the raw and refined state, using the data obtained by gas chromatography. The fatty acids of the oil were determined as methylic esteres. The analyst was carried out in a gas chromatographer, with a detector of ionization by way of flame (FID), Agilent 7890A (Agilent, USA) coupled to HP Pentium 4 computer, with a data processing program. The temperatures of the injector and of the detector were 250 °C and 260 °C respectively. The data obtained chromatographically of the oil of Jatropha curcas L, raw and refined indicates that the refinery process did not vary the composition of the fatty acid, because there are no significant differences between them. Also, the results obtained by other investigators, showed that the predominant fatty acids obtained from the oil of the Jatropha curcas L were palmitic and stearic in the saturated fatty acids, and oleic and linoleic in the unsaturated fatty acids

Chromatography analysis of Jatropha Curcas L oil raw and refined

International Nuclear Information System (INIS)

Chitue de Assuncao Nascimento, Juliano; Lafargue Perez, Francisco; Diaz Velazquez, Manuel

2013-01-01

The chromatography of gases is one of the most versatile methods utilized in the chemical laboratory, which permits the determinations of the percentages and types of fatty acids present in vegetable oils. The objective of this work was to carry out a comparative study of the composition of the fatty acids, of the mechanically extracted oil from the seed of the Jatropha curcas L plant in the raw and refined state, using the data obtained by gas chromatography. The fatty acids of the oil were determined as methylic esteres. The analyst was carried out in a gas chromatographer, with a detector of ionization by way of flame (FID), Agilent 7890A (Agilent, USA) coupled to HP Pentium 4 computer, with a data processing program. The temperatures of the injector and of the detector were 250℃ and 260℃ respectively. The data obtained chromatographically of the oil of Jatropha curcas L, raw and refined indicates that the refinery process did not vary the composition of the fatty acid, because there are no significant differences between them. Also, the results obtained by other investigators, showed that the predominant fatty acids obtained from the oil of the Jatropha curcas L were palmitic and stearic in the saturated fatty acids, and oleic and linoleic in the unsaturated fatty acids

Directory of Certificates of Compliance for radioactive materials packages: Report of NRC approved quality assurance programs for radioactive materials packages. Volume 3, Revision 15

International Nuclear Information System (INIS)

1995-10-01

The purpose of this directory is to make available a convenient source of information on packagings which have been approved by the US Nuclear Regulatory Commission. To assist in identifying packaging, an index by Model Number and corresponding Certificate of Compliance Number is included at the front of Volumes 1 and 2. An alphabetical listing by user name is included in the back of Volume 3 of approved QA programs. The reports include a listing of all users of each package design and approved QA programs prior to the publication date

ASEAN-USAID buildings energy conservation project. Volume 1, Energy standards: Final report

Energy Technology Data Exchange (ETDEWEB)

Levine, M.D.; Busch, J.F. [eds.][Lawrence Berkeley Lab., CA (United States); Deringer, J.J. [Deringer Group, Riva, MD (United States)

1992-06-01

Mandatory or voluntary energy-efficiency standards for new or existing buildings can play an important role in a national program aimed at promoting energy conservation. Building codes and standards can provide a degree of control over design and building practices throughout the construction process, and encourage awareness of energy-conscious design. Studies in developed countries indicate that efficiency standards can produce energy reductions on the order of 20 to 40% or more. Within ASEAN, analyses of the savings potential from the proposed standards suggest that if implemented, these standards would produce savings over current new design practice of 19% to 24%. In this volume we provide an overview of the ASEAN-USAID project aimed at promulgating standards for energy efficiency in commercial buildings. The process of developing and implementing energy-efficiency standards for buildings can be subdivided into two key components: policy development; and technical and economic analysis. Each of these involves a number of steps and processes, as outlined in Figure 1-1. This volume describes the technical and economic analyses used to develop the proposed energy efficiency standards for four countries (Malaysia, Thailand, the Philippines, and Indonesia), and to refine an energy standard existing in Singapore since 1979. Though oriented toward the ASEAN region, the analysis methods described here are applicable in a range of settings, provided appropriate modifications are made for local building construction, climatic, economic, and political conditions. Implementation issues are not specifically addressed here; rather this volume is oriented towards the analytical work needed to establish or revise an energy standard for buildings.

Development, Verification and Validation of Parallel, Scalable Volume of Fluid CFD Program for Propulsion Applications

Science.gov (United States)

West, Jeff; Yang, H. Q.

2014-01-01

There are many instances involving liquid/gas interfaces and their dynamics in the design of liquid engine powered rockets such as the Space Launch System (SLS). Some examples of these applications are: Propellant tank draining and slosh, subcritical condition injector analysis for gas generators, preburners and thrust chambers, water deluge mitigation for launch induced environments and even solid rocket motor liquid slag dynamics. Commercially available CFD programs simulating gas/liquid interfaces using the Volume of Fluid approach are currently limited in their parallel scalability. In 2010 for instance, an internal NASA/MSFC review of three commercial tools revealed that parallel scalability was seriously compromised at 8 cpus and no additional speedup was possible after 32 cpus. Other non-interface CFD applications at the time were demonstrating useful parallel scalability up to 4,096 processors or more. Based on this review, NASA/MSFC initiated an effort to implement a Volume of Fluid implementation within the unstructured mesh, pressure-based algorithm CFD program, Loci-STREAM. After verification was achieved by comparing results to the commercial CFD program CFD-Ace+, and validation by direct comparison with data, Loci-STREAM-VoF is now the production CFD tool for propellant slosh force and slosh damping rate simulations at NASA/MSFC. On these applications, good parallel scalability has been demonstrated for problems sizes of tens of millions of cells and thousands of cpu cores. Ongoing efforts are focused on the application of Loci-STREAM-VoF to predict the transient flow patterns of water on the SLS Mobile Launch Platform in order to support the phasing of water for launch environment mitigation so that vehicle determinantal effects are not realized.

Variable thickness transient ground-water flow model. Volume 3. Program listings

International Nuclear Information System (INIS)

Reisenauer, A.E.

1979-12-01

The Assessment of Effectiveness of Geologic Isolation Systems (AEGIS) Program is developing and applying the methodology for assessing the far-field, long-term post-closure safety of deep geologic nuclear waste repositories. AEGIS is being performed by Pacific Northwest Laboratory (PNL) under contract with the Office of Nuclear Waste Isolation (OWNI) for the Department of Energy (DOE). One task within AEGIS is the development of methodology for analysis of the consequences (water pathway) from loss of repository containment as defined by various release scenarios. Analysis of the long-term, far-field consequences of release scenarios requires the application of numerical codes which simulate the hydrologic systems, model the transport of released radionuclides through the hydrologic systems to the biosphere, and, where applicable, assess the radiological dose to humans. Hydrologic and transport models are available at several levels of complexity or sophistication. Model selection and use are determined by the quantity and quality of input data. Model development under AEGIS and related programs provides three levels of hydrologic models, two levels of transport models, and one level of dose models (with several separate models). This is the third of 3 volumes of the description of the VTT (Variable Thickness Transient) Groundwater Hydrologic Model - second level (intermediate complexity) two-dimensional saturated groundwater flow

Strategic issues and implications for the refining and marketing sector

International Nuclear Information System (INIS)

Jeffe, R.A.

1995-01-01

Refiners have faced a challenging business environment for the past decade. During this period, the industry has made approximately $25 billion of capital expenditures primarily to comply with increased governmental mandates, faced highly volatile petroleum product prices and garnered a return to equity of only 5%. While worldwide and US refining capacity has been flat in recent years, demand for refined petroleum products has been on the upswing and domestic supplies have also increased due to improved US capacity utilization rates (76% in 1984 and 93% in 1994) and increased imports (gasoline sales up 11% since 1984). The result has been highly volatile and generally weak refining margins (net Gulf Coast crack spread ranging from ($.95)/bbl in 1984 to $1.84/bbl in 1990 and averaging $.81/bbl since 1984). In response to the sustained difficulties in the marketplace, one has recently witnessed some strategic realignment in the industry. Several of the integrated companies, frustrated with the required capital expenditures and meager returns, have decided to shed non-core, non-strategic refining assets. For the most part, these assets have been bought by independents at, by historical measures, very attractive terms. This paper will provide an overview of the economics of the refining business, discuss the recent trends in refinery M and A activity and summarize possible implications of the recent strategic realignment

Field Operations and Enforcement Manual for Air Pollution Control. Volume III: Inspection Procedures for Specific Industries.

Science.gov (United States)

Weisburd, Melvin I.

The Field Operations and Enforcement Manual for Air Pollution Control, Volume III, explains in detail the following: inspection procedures for specific sources, kraft pulp mills, animal rendering, steel mill furnaces, coking operations, petroleum refineries, chemical plants, non-ferrous smelting and refining, foundries, cement plants, aluminum…

EFFECT OF REFINED PETROLEUM PRODUCTS CONTAMINATION ON BACTERIAL POPULATION AND PHYSICOCHEMICAL CHARACTERISTICS OF CULTIVATED AGRICULTURAL SOIL

Directory of Open Access Journals (Sweden)

Adewale Sogo Olalemi

2012-10-01

Full Text Available An investigation into the effect of refined petroleum products contamination on bacterial population and physicochemical characteristics of cultivated agricultural soil was carried out. The soil samples obtained from the Teaching and Research Farm, Obakekere, Federal University of Technology, Akure, Ondo State were contaminated with varying volumes of petrol, diesel and kerosene. The results revealed higher bacterial populations in uncontaminated soils than contaminated soils. The counts of bacteria ranged from 3.0 × 105 to 5.0 × 105 cfu/g in uncontaminated soils and 1.0 × 105 to 3.0 × 105 cfu/g in contaminated soils. The isolated bacteria were identified as Bacillus subtilis, Flavobacterium lutescens, Micrococcus luteus, Corynebacterium variabilis, Pseudomonas fluorescens. The contamination had no significant effect on pH, potassium, sodium, organic carbon and nitrogen content of the soils, while the moisture, calcium, phosphorus and magnesium content of the contaminated soils were significantly different (P < 0.05 compared with the uncontaminated soils. The ability of Bacillus subtilis, Flavobacterium lutescens, Micrococcus luteus, and Pseudomonas fluorescens to utilize the refined petroleum products suggest that these bacteria had potential to bioremediate petroleum contaminated soils.

Preparation of Al-Ti-B grain refiner by SHS technology

International Nuclear Information System (INIS)

Nikitin, V.I.; Wanqi, J.I.E.; Kandalova, E.G.; Makarenko, A.G.; Yong, L.

2000-01-01

Since the discovery of the grain refinement effect of aluminum by titanium, especially with the existence of B or C in 1950, grain refiners are widely accepted in industry for microstructure control of aluminum alloys. Research on this topic is to obtain the highest grain refinement efficiency with the lowest possible addition of master alloy. It is widely accepted that the morphology and size of TiAl 3 particles, which are known as heterogeneous nucleation centers, are important factors deterring the grain refinement efficiency. Fine TiAl 3 particles are favorable. The grain refinement process shows a heredity phenomenon, which means that structural information from initial materials transfers through a melt to the final product. It is important to find the connection between microstructural parameters of the master alloy and the final product. To improve the quality of Al-Ti-B master alloys for the use as a grain refiner, a new method based on SHS (self-propagating high-temperature synthesis) technology has been developed in Samara State Technical University to produce the master alloys. SHS, as a new method for preparation of materials, was first utilized by Merzhanov in 1967. This method uses the energy from highly exothermic reactions to sustain the chemical reaction in a combustion wave. The advantages of SHS include simplicity, low energy requirement, and higher product purity. Because SHS reactions can take place between elemental reactants, it is easy to control product composition. The purposes of this investigation were to fabricate an SHS Al-5%Ti-1%B master alloy, to analyze its structure and to test its grain refining performance

Formal refinement of extended state machines

Directory of Open Access Journals (Sweden)

Thomas Fayolle

2016-06-01

Full Text Available In a traditional formal development process, e.g. using the B method, the informal user requirements are (manually translated into a global abstract formal specification. This translation is especially difficult to achieve. The Event-B method was developed to incrementally and formally construct such a specification using stepwise refinement. Each increment takes into account new properties and system aspects. In this paper, we propose to couple a graphical notation called Algebraic State-Transition Diagrams (ASTD with an Event-B specification in order to provide a better understanding of the software behaviour. The dynamic behaviour is captured by the ASTD, which is based on automata and process algebra operators, while the data model is described by means of an Event-B specification. We propose a methodology to incrementally refine such specification couplings, taking into account new refinement relations and consistency conditions between the control specification and the data specification. We compare the specifications obtained using each approach for readability and proof complexity. The advantages and drawbacks of the traditional approach and of our methodology are discussed. The whole process is illustrated by a railway CBTC-like case study. Our approach is supported by tools for translating ASTD's into B and Event-B into B.

Mirror of the refined topological vertex from a matrix model

CERN Document Server

Eynard, B

2011-01-01

We find an explicit matrix model computing the refined topological vertex, starting from its representation in terms of plane partitions. We then find the spectral curve of that matrix model, and thus the mirror symmetry of the refined vertex. With the same method we also find a matrix model for the strip geometry, and we find its mirror curve. The fact that there is a matrix model shows that the refined topological string amplitudes also satisfy the remodeling the B-model construction.

Direct Reduction of Waste through Refining of DOE Metal Assets - 13632

International Nuclear Information System (INIS)

Hargett, Michael C.; Terekhov, Dimitri; Khozan, Kamran M.

2013-01-01

CVMR R presents a technology for refining nickel from the enrichment barrier materials of the DOE that is proven through 100 years of use by the metals industry. CVMR R applies modern controls, instrumentation for process and monitoring of the system, and innovative production methods to produce a wide spectrum of products that generate new technology applications and improvements to our society and economy. CVMR R will receive barrier materials as a secure operation and size reduce the metal to a shred that is fed to a carbonylation reactor where nickel is reacted with carbon monoxide and generate nickel carbonyl. The carbonyl will be filtered and decomposed with heat to form a variety of products that include high value nano powders, coated substrates, net shapes and pure nickel. The residue from the reactor will retain radionuclides from enrichment activities. The carbon monoxide will only react and extract nickel under the operating conditions to leave volumetric contamination in the unreacted residue. A demonstration plant was designed and built by CVMR R and operated by BWXT, to demonstrate the systems capabilities to DOE in 2006. A pilot plant operation precedes the detailed design of the nickel refinery and provides essential data for design, safe work practices, waste characterizations and system kinetics and confirms the project feasibility. CVMR R produces nickel products that are cleaner than the nickel in U.S. commerce and used by industry today. The CVMR R process and systems for nickel refining is well suited for DOE materials and will provide value through environmental stewardship, recovery of high value assets, and support of the DOE environmental remediation programs as the refined nickel generates additional long term benefits to local communities. (authors)

Ab initio structure determination and refinement of a scorpion protein toxin.

Science.gov (United States)

Smith, G D; Blessing, R H; Ealick, S E; Fontecilla-Camps, J C; Hauptman, H A; Housset, D; Langs, D A; Miller, R

1997-09-01

The structure of toxin II from the scorpion Androctonus australis Hector has been determined ab initio by direct methods using SnB at 0.96 A resolution. For the purpose of this structure redetermination, undertaken as a test of the minimal function and the SnB program, the identity and sequence of the protein was withheld from part of the research team. A single solution obtained from 1 619 random atom trials was clearly revealed by the bimodal distribution of the final value of the minimal function associated with each individual trial. Five peptide fragments were identified from a conservative analysis of the initial E-map, and following several refinement cycles with X-PLOR, a model was built of the complete structure. At the end of the X-PLOR refinement, the sequence was compared with the published sequence and 57 of the 64 residues had been correctly identified. Two errors in sequence resulted from side chains with similar size while the rest of the errors were a result of severe disorder or high thermal motion in the side chains. Given the amino-acid sequence, it is estimated that the initial E-map could have produced a model containing 99% of all main-chain and 81% of side-chain atoms. The structure refinement was completed with PROFFT, including the contributions of protein H atoms, and converged at a residual of 0.158 for 30 609 data with F >or= 2sigma(F) in the resolution range 8.0-0.964 A. The final model consisted of 518 non-H protein atoms (36 disordered), 407 H atoms, and 129 water molecules (43 with occupancies less than unity). This total of 647 non-H atoms represents the largest light-atom structure solved to date.

Effect of Chemical Refining on Citrullus Colocynthis and Pongamia ...

African Journals Online (AJOL)

Oil from the both plant seeds was evaluated (both before and after refining) for different physico-chemical parameters like free fatty acids, iodine value, peroxide value, saponification value, unsaponifiable matter and fatty acid composition. Oil yield (30-35 %) in both plants was found average. After refining, per cent reduction ...

Dancetime! 500 Years of Social Dance. Volume I: 15th-19th Centuries. [Videotape].

Science.gov (United States)

Teten, Carol

This VHS videotape recording is the first in a two-volume series that presents 500 years of social dance, music, and fashion. It focuses on the 15th-19th centuries, including Renaissance nobility, Baroque extravagance, Regency refinement, and Victorian romanticism. Each era reflects the changing relationships between men and women through the…

Nuclear proliferation and civilian nuclear power. Report of the Nonproliferation Alternative Systems Assessment Program. Volume IV. Commercial potential

Energy Technology Data Exchange (ETDEWEB)

1980-06-01

This volume of the Nonproliferation Alternative Systems Assessment Program (NASAP) report provides time and cost estimates for positioning new nuclear power systems for commercial deployment. The assessment also estimates the rates at which the new systems might penetrate the domestic market, assuming the continuing viability of the massive light-water reactor network that now exists worldwide. This assessment does not recommend specific, detailed program plans and budgets for individual systems; however, it is clear from this analysis that any of the systems investigated could be deployed if dictated by national interest.

Nuclear proliferation and civilian nuclear power. Report of the Nonproliferation Alternative Systems Assessment Program. Volume IV. Commercial potential

International Nuclear Information System (INIS)

1980-06-01

This volume of the Nonproliferation Alternative Systems Assessment Program (NASAP) report provides time and cost estimates for positioning new nuclear power systems for commercial deployment. The assessment also estimates the rates at which the new systems might penetrate the domestic market, assuming the continuing viability of the massive light-water reactor network that now exists worldwide. This assessment does not recommend specific, detailed program plans and budgets for individual systems; however, it is clear from this analysis that any of the systems investigated could be deployed if dictated by national interest

Rotorcraft Flight Simulation Computer Program C81 with Datamap Interface, Volume 2. Programmer’s Manual

Science.gov (United States)

1981-10-01

overview of the computer program capabilities and the principal mathematical models incorporated in the program are given in Volume I of the documentation...blank card must still be placed in the appropriate place in the Model Data Set. For example, the mathematical model of a UH-lH would not need a wing...SIN %4114 LV OADs CC £6 $ 2. 27 4L 4+ 4 l’l <m L & % CC O 04i18K5 twsSTVEL 13L4.S2 ASK 2? b 41.815 . 8 ’ILbLS a CL 7 8 £0 1 £0 £0 12 £6 1 M90 A/ MUfI H

Refined analysis results for multimedia network costs and profits

DEFF Research Database (Denmark)

Tahkokorpi, M.; Falch, Morten; Skouby, Knud Erik

This deliverable describes the techno-economic business model developed in EURORIM WP3 and presents the refined results of the multimedia service delivery cost-profit calculations......This deliverable describes the techno-economic business model developed in EURORIM WP3 and presents the refined results of the multimedia service delivery cost-profit calculations...

Refining and petrochemicals

International Nuclear Information System (INIS)

Benazzi, E.

2003-01-01

Down sharply in 2002, refining margins showed a clear improvement in the first half-year of 2003. As a result, the earnings reported by oil companies for financial year 2002 were significantly lower than in 2001, but the prospects are brighter for 2003. In the petrochemicals sector, slow demand and higher feedstock prices eroded margins in 2002, especially in Europe and the United States. The financial results for the first part of 2003 seem to indicate that sector profitability will not improve before 2004. (author)

Refining of biodiesel by ceramic membrane separation

Energy Technology Data Exchange (ETDEWEB)

Wang, Yong; Ou, Shiyi; Tan, Yanlai; Tang, Shuze [Department of Food Science and Engineering, Jinan University, Guangzhou 510632 (China); Wang, Xingguo; Liu, Yuanfa [School of Food Science and Technology, Jiangnan University, Wuxi 214112 (China)

2009-03-15

A ceramic membrane separation process for biodiesel refining was developed to reduce the considerable usage of water needed in the conventional water washing process. Crude biodiesel produced by refined palm oil was micro-filtered by ceramic membranes of the pore size of 0.6, 0.2 and 0.1 {mu}m to remove the residual soap and free glycerol, at the transmembrane pressure of 0.15 MPa and temperature of 60 C. The flux through membrane maintained at 300 L m{sup -} {sup 2} h{sup -} {sup 1} when the volumetric concentrated ratio reached 4. The content of potassium, sodium, calcium and magnesium in the whole permeate was 1.40, 1.78, 0.81 and 0.20 mg/kg respectively, as determined by inductively coupled plasma-atomic emission spectroscopy. These values are lower than the EN 14538 specifications. The residual free glycerol in the permeate was estimated by water extraction, its value was 0.0108 wt.%. This ceramic membrane technology was a potential environmental process for the refining of biodiesel. (author)

Production of Al-Ti-C grain refiners with the addition of elemental carbon

International Nuclear Information System (INIS)

Gezer, Berke Turgay; Toptan, Fatih; Daglilar, Sibel; Kerti, Isil

2010-01-01

Grain refining process used in aluminium alloys, has an important role for preventing columnar, coarse grains and encouraging fine, equiaxed grain formation. Al-Ti-B grain refiners are widely used as aluminium grain refiners despite the problems in application Al-Ti-C refiners have an increasing demand in recent years. In the present work, Al-Ti-C grain refiners with different Ti:C ratios were produced by insitu method with the addition of elemental carbon. Microstructures were characterised by optic microscope and scanning electron microscope equipped with energy dispersive spectroscopy. The effects of temperature, holding time and Ti:C ratio on the grain refinement process were investigated and optimum conditions were determined.

European oil refining: strategies for a competitive future

International Nuclear Information System (INIS)

MacDonald, James.

1997-07-01

European Oil Refining investigates how the industry came to be in crisis and what the future holds. As well as an extensive analysis of past and present market shifts, the report predicts likely future developments and their consequences for investors. The report reviews the European oil sector in a global context, calculates the cost to refiners of key environmental legislation, assesses the problems caused by changing product demand and crude supply, examines possible solutions to the problems of low margins and overcapacity, evaluates the key players' main strategies to increase their competitiveness, analyses the western European oil refining industry by country, details the refinery operations of the major countries of central and eastern Europe, profiles 15 of the major oil companies and estimates the increase in investment required as a result of legislative and demand changes. (author)

An adaptive mesh refinement approach for average current nodal expansion method in 2-D rectangular geometry

International Nuclear Information System (INIS)

Poursalehi, N.; Zolfaghari, A.; Minuchehr, A.

2013-01-01

Highlights: ► A new adaptive h-refinement approach has been developed for a class of nodal method. ► The resulting system of nodal equations is more amenable to efficient numerical solution. ► The benefit of the approach is reducing computational efforts relative to the uniform fine mesh modeling. ► Spatially adaptive approach greatly enhances the accuracy of the solution. - Abstract: The aim of this work is to develop a spatially adaptive coarse mesh strategy that progressively refines the nodes in appropriate regions of domain to solve the neutron balance equation by zeroth order nodal expansion method. A flux gradient based a posteriori estimation scheme has been utilized for checking the approximate solutions for various nodes. The relative surface net leakage of nodes has been considered as an assessment criterion. In this approach, the core module is called in by adaptive mesh generator to determine gradients of node surfaces flux to explore the possibility of node refinements in appropriate regions and directions of the problem. The benefit of the approach is reducing computational efforts relative to the uniform fine mesh modeling. For this purpose, a computer program ANRNE-2D, Adaptive Node Refinement Nodal Expansion, has been developed to solve neutron diffusion equation using average current nodal expansion method for 2D rectangular geometries. Implementing the adaptive algorithm confirms its superiority in enhancing the accuracy of the solution without using fine nodes throughout the domain and increasing the number of unknown solution. Some well-known benchmarks have been investigated and improvements are reported

Current research progress in grain refinement of cast magnesium alloys: A review article

International Nuclear Information System (INIS)

Ali, Yahia; Qiu, Dong; Jiang, Bin; Pan, Fusheng; Zhang, Ming-Xing

2015-01-01

Grain refinement of cast magnesium alloys, particularly in magnesium–aluminium (Mg–Al) based alloys, has been an active research topic in the past two decades, because it has been considered as one of the most effective approaches to simultaneously increase the strength, ductility and formability. The development of new grain refiners was normally based on the theories/models that were established through comprehensive and considerable studies of grain refinement in cast Al alloys. Generally, grain refinement in cast Al can be achieved through either inoculation treatment, which is a process of adding, or in situ forming, foreign particles to promote heterogeneous nucleation rate, or restricting grain growth by controlling the constitutional supercooling or both. But, the concrete and tangible grain refinement mechanism in cast metals is still not fully understood and there are a number of controversies. Therefore, most of the new developed grain refiners for Mg–Al based alloys are not as efficient as the commercially available ones, such as zirconium in non-Al containing Mg alloys. To facilitate the research in grain refinement of cast magnesium alloys, this review starts with highlighting the theoretical aspects of grain refinement in cast metals, followed by reviewing the latest research progress in grain refinement of magnesium alloys in terms of the solute effect and potent nucleants

Current research progress in grain refinement of cast magnesium alloys: A review article

Energy Technology Data Exchange (ETDEWEB)

Ali, Yahia; Qiu, Dong [School of Mechanical and Mining Engineering, University of Queensland, St Lucia, QLD 4072 (Australia); Jiang, Bin; Pan, Fusheng [College of Materials Science and Engineering, Chongqing University, Chongqing 400030 (China); Zhang, Ming-Xing, E-mail: Mingxing.Zhang@uq.edu.au [School of Mechanical and Mining Engineering, University of Queensland, St Lucia, QLD 4072 (Australia)

2015-01-15

Grain refinement of cast magnesium alloys, particularly in magnesium–aluminium (Mg–Al) based alloys, has been an active research topic in the past two decades, because it has been considered as one of the most effective approaches to simultaneously increase the strength, ductility and formability. The development of new grain refiners was normally based on the theories/models that were established through comprehensive and considerable studies of grain refinement in cast Al alloys. Generally, grain refinement in cast Al can be achieved through either inoculation treatment, which is a process of adding, or in situ forming, foreign particles to promote heterogeneous nucleation rate, or restricting grain growth by controlling the constitutional supercooling or both. But, the concrete and tangible grain refinement mechanism in cast metals is still not fully understood and there are a number of controversies. Therefore, most of the new developed grain refiners for Mg–Al based alloys are not as efficient as the commercially available ones, such as zirconium in non-Al containing Mg alloys. To facilitate the research in grain refinement of cast magnesium alloys, this review starts with highlighting the theoretical aspects of grain refinement in cast metals, followed by reviewing the latest research progress in grain refinement of magnesium alloys in terms of the solute effect and potent nucleants.

STRCMACS: An extensive set of Macros for structured programming in OS/360 assembly language

Science.gov (United States)

Barth, C. W.

1974-01-01

Two techniques are discussed that have been most often referred to as structured programming. One is that of programming with high level control structures (such as the if and while) replacing the branch instruction (goto-less programming); the other is the process of developing a program by progressively refining descriptions of components in terms of more primitive components (called stepwise refinement or top-down programming). In addition to discussing what these techniques are, it is shown why their use is advised and how both can be implemented in OS assembly language by the use of a special macro instruction package.

Analysis model for forecasting extreme temperature using refined rank set pair

Directory of Open Access Journals (Sweden)

Qiao Ling-Xia

2013-01-01

Full Text Available In order to improve the precision of forecasting extreme temperature time series, a refined rank set pair analysis model with a refined rank transformation function is proposed to improve precision of its prediction. The measured values of the annual highest temperature of two China’s cities, Taiyuan and Shijiazhuang, in July are taken to examine the performance of a refined rank set pair model.

Potency of high-intensity ultrasonic treatment for grain refinement of magnesium alloys

International Nuclear Information System (INIS)

Ramirez, A.; Qian Ma; Davis, B.; Wilks, T.; StJohn, D.H.

2008-01-01

High-intensity ultrasonic treatment (UT) for grain refinement of magnesium alloys has been investigated using a novel theoretical approach in order to better understand its grain-refining potential and the mechanism of nucleation. The process demonstrated significantly superior grain-refining potency to carbon inoculation for Al-containing magnesium alloys but inferior potency to zirconium for Al-free alloys. Details revealed by applying the theoretical approach to ultrasonic grain refinement provide new clues to understanding the mechanism of grain nucleation by UT

Trends in heavy oil production and refining in California

International Nuclear Information System (INIS)

Olsen, D.K.; Ramzel, E.B.; Pendergrass, R.A. II.

1992-07-01

This report is one of a series of publications assessing the feasibility of increasing domestic heavy oil production and is part of a study being conducted for the US Department of Energy. This report summarizes trends in oil production and refining in Canada. Heavy oil (10 degrees to 20 degrees API gravity) production in California has increased from 20% of the state's total oil production in the early 1940s to 70% in the late 1980s. In each of the three principal petroleum producing districts (Los Angeles Basin, Coastal Basin, and San Joaquin Valley) oil production has peaked then declined at different times throughout the past 30 years. Thermal production of heavy oil has contributed to making California the largest producer of oil by enhanced oil recovery processes in spite of low oil prices for heavy oil and stringent environmental regulation. Opening of Naval Petroleum Reserve No. 1, Elk Hills (CA) field in 1976, brought about a major new source of light oil at a time when light oil production had greatly declined. Although California is a major petroleum-consuming state, in 1989 the state used 13.3 billion gallons of gasoline or 11.5% of US demand but it contributed substantially to the Nation's energy production and refining capability. California is the recipient and refines most of Alaska's 1.7 million barrel per day oil production. With California production, Alaskan oil, and imports brought into California for refining, California has an excess of oil and refined products and is a net exporter to other states. The local surplus of oil inhibits exploitation of California heavy oil resources even though the heavy oil resources exist. Transportation, refining, and competition in the market limit full development of California heavy oil resources

RETRAN-02: a program for transient thermal-hydraulic analysis of complex fluid-flow systems. Volume 4. Applications

International Nuclear Information System (INIS)

Peterson, C.E.; Gose, G.C.; McFadden, J.H.

1983-01-01

RETRAN-02 represents a significant achievement in the development of a versatile and reliable computer program for use in best estimate transient thermal-hydraulic analysis of light water reactor systems. The RETRAN-02 computer program is an extension of the RETRAN-01 program designed to provide analysis capabilities for 1) BWR and PWR transients, 2) small break loss of coolant accidents, 3) balance of plant modeling, and 4) anticipated transients without scram, while maintaining the analysis capabilities of the predecessor code. The RETRAN-02 computer code is constructed in a semimodular and dynamic dimensioned form where additions to the code can be easily carried out as new and improved models are developed. This report (the fourth of a five volume computer code manual) describes the verification and validation of RETRAN-02

The relation between media promotions and service volume for a statewide tobacco quitline and a web-based cessation program

Directory of Open Access Journals (Sweden)

Schillo Barbara A

2011-12-01

Full Text Available Abstract Background This observational study assessed the relation between mass media campaigns and service volume for a statewide tobacco cessation quitline and stand-alone web-based cessation program. Methods Multivariate regression analysis was used to identify how weekly calls to a cessation quitline and weekly registrations to a web-based cessation program are related to levels of broadcast media, media campaigns, and media types, controlling for the impact of external and earned media events. Results There was a positive relation between weekly broadcast targeted rating points and the number of weekly calls to a cessation quitline and the number of weekly registrations to a web-based cessation program. Additionally, print secondhand smoke ads and online cessation ads were positively related to weekly quitline calls. Television and radio cessation ads and radio smoke-free law ads were positively related to web program registration levels. There was a positive relation between the number of web registrations and the number of calls to the cessation quitline, with increases in registrations to the web in 1 week corresponding to increases in calls to the quitline in the subsequent week. Web program registration levels were more highly influenced by earned media and other external events than were quitline call volumes. Conclusion Overall, broadcast advertising had a greater impact on registrations for the web program than calls to the quitline. Furthermore, registrations for the web program influenced calls to the quitline. These two findings suggest the evolving roles of web-based cessation programs and Internet-use practices should be considered when creating cessation programs and media campaigns to promote them. Additionally, because different types of media and campaigns were positively associated with calls to the quitline and web registrations, developing mass media campaigns that offer a variety of messages and communicate through

Need for refining capacity creates opportunities for producers in Middle East

International Nuclear Information System (INIS)

Ali, M.S.S.

1994-01-01

Oil industry interest in refining has revived in the past few years in response to rising oil consumption. The trend creates opportunities, for countries in the Middle East, which do not own refining assets nearly in proportion to their crude oil reserved. By closing this gap between reserves and refining capacity, the countries can ease some of the instability now characteristic of the oil market. Some major oil producing countries have begun to move downstream. During the 1980s, Venezuela, Kuwait, Saudi Arabia, Libya, and other members of the Organization of Petroleum Exporting Countries acquired refining assets through direct total purchase or joint ventures. Nevertheless, the oil industry remains largely unintegrated, with the Middle East holding two thirds of worldwide oil reserves but only a small share downstream. As worldwide refining capacity swings from a period of surplus toward one in which the need for new capacity will be built. The paper discusses background of the situation, shrinking surplus, investment requirements, sources of capital, and shipping concerns

A grid-enabled web service for low-resolution crystal structure refinement.

Science.gov (United States)

O'Donovan, Daniel J; Stokes-Rees, Ian; Nam, Yunsun; Blacklow, Stephen C; Schröder, Gunnar F; Brunger, Axel T; Sliz, Piotr

2012-03-01

Deformable elastic network (DEN) restraints have proved to be a powerful tool for refining structures from low-resolution X-ray crystallographic data sets. Unfortunately, optimal refinement using DEN restraints requires extensive calculations and is often hindered by a lack of access to sufficient computational resources. The DEN web service presented here intends to provide structural biologists with access to resources for running computationally intensive DEN refinements in parallel on the Open Science Grid, the US cyberinfrastructure. Access to the grid is provided through a simple and intuitive web interface integrated into the SBGrid Science Portal. Using this portal, refinements combined with full parameter optimization that would take many thousands of hours on standard computational resources can now be completed in several hours. An example of the successful application of DEN restraints to the human Notch1 transcriptional complex using the grid resource, and summaries of all submitted refinements, are presented as justification.

Refining and petrochemicals

International Nuclear Information System (INIS)

Benazzi, E.; Alario, F.

2004-01-01

In 2003, refining margins showed a clear improvement that continued throughout the first three quarters of 2004. Oil companies posted significantly higher earnings in 2003 compared to 2002, with the results of first quarter 2004 confirming this trend. Due to higher feedstock prices, the implementation of new capacity and more intense competition, the petrochemicals industry was not able to boost margins in 2003. In such difficult business conditions, aggravated by soaring crude prices, the petrochemicals industry is not likely to see any improvement in profitability before the second half of 2004. (author)

Initiating technical refinements in high-level golfers: Evidence for contradictory procedures.

Science.gov (United States)

Carson, Howie J; Collins, Dave; Richards, Jim

2016-01-01

When developing motor skills there are several outcomes available to an athlete depending on their skill status and needs. Whereas the skill acquisition and performance literature is abundant, an under-researched outcome relates to the refinement of already acquired and well-established skills. Contrary to current recommendations for athletes to employ an external focus of attention and a representative practice design,  Carson and  Collins' (2011) [Refining and regaining skills in fixation/diversification stage performers: The Five-A Model. International Review of Sport and Exercise Psychology, 4, 146-167. doi: 10.1080/1750984x.2011.613682 ] Five-A Model requires an initial narrowed internal focus on the technical aspect needing refinement: the implication being that environments which limit external sources of information would be beneficial to achieving this task. Therefore, the purpose of this paper was to (1) provide a literature-based explanation for why techniques counter to current recommendations may be (temporarily) appropriate within the skill refinement process and (2) provide empirical evidence for such efficacy. Kinematic data and self-perception reports are provided from high-level golfers attempting to consciously initiate technical refinements while executing shots onto a driving range and into a close proximity net (i.e. with limited knowledge of results). It was hypothesised that greater control over intended refinements would occur when environmental stimuli were reduced in the most unrepresentative practice condition (i.e. hitting into a net). Results confirmed this, as evidenced by reduced intra-individual movement variability for all participants' individual refinements, despite little or no difference in mental effort reported. This research offers coaches guidance when working with performers who may find conscious recall difficult during the skill refinement process.

Ion channels involved in cell volume regulation: effects on migration, proliferation, and programmed cell death in non adherent EAT cells and adherent ELA cells.

Science.gov (United States)

Hoffmann, Else Kay

2011-01-01

This mini review outlines studies of cell volume regulation in two closely related mammalian cell lines: nonadherent Ehrlich ascites tumour cells (EATC) and adherent Ehrlich Lettre ascites (ELA) cells. Focus is on the regulatory volume decrease (RVD) that occurs after cell swelling, the volume regulatory ion channels involved, and the mechanisms (cellular signalling pathways) that regulate these channels. Finally, I shall also briefly review current investigations in these two cell lines that focuses on how changes in cell volume can regulate cell functions such as cell migration, proliferation, and programmed cell death. Copyright © 2011 S. Karger AG, Basel.

Grain refinement through severe plastic deformation (SPD) processing

International Nuclear Information System (INIS)

Izairi, N.; Vevecka - Priftaj, A.

2012-01-01

There is considerable current interest in processing metallic samples through procedures involving the imposition of severe plastic deformation (SPD). These procedures lead to very significant grain refinement to the submicrometer or even the nanometer level, resulting in advanced physical properties. Among various SPD processes, Equal Channel Angular Pressing, High pressure Torsion and Accumulated Roll Bonding have been widely used for many metals and alloys. In the present work, we present an overview of the most used methods of SPD for grain refinement and the production of bulk nano structured materials with enhancement in their mechanical and functional properties. In order to examine the potential for using ECAP to refine the grain size and improve the mechanical properties, two commercial 5754 Al alloy and AA 3004 , were selected for study. Processing by ECAP gives a reduction in the grain size and an increase in the microhardness. (Author)

Future prospects for palm oil refining and modifications

Directory of Open Access Journals (Sweden)

Gibon Véronique

2009-07-01

Full Text Available Palm oil is rich in minor components that impart unique nutritional properties and need to be preserved. In this context, refining technologies have been improved, with the dual temperature deodorizer, the double condensing unit and the ice condensing system. The DOBI is a good tool to assess quality of the crude palm oil and its ability to be properly refined. Specially refined oils open a market for new high quality products (golden palm oil, red palm oil, white soaps, etc.. Palm oil is a good candidate for the multi-step dry fractionation process, aiming to the production of commodity oils and specialty fats (cocoa butter replacers. New technological developments allow quality and yield improvements. Palm oil and fractions are also valuable feedstock for enzymatic interesterification in which applications are for commodity oil (low-trans margarines and shortenings and for special products (cocoa butter equivalents, infant formulation, ….

Unilever food safety assurance system for refined vegetable oils and fats

Directory of Open Access Journals (Sweden)

van Duijn Gerrit

2010-03-01

Full Text Available The Unilever Food Safety Assurance system for refined oils and fats is based on risk assessments for the presence of contaminants or pesticide residues in crude oils, and refining process studies to validate the removal of these components. Crude oil risk assessments were carried out by combining supply chain visits, and analyses of the contaminant and pesticide residue levels in a large number of crude oil samples. Contaminants like poly-aromatic hydrocarbons and hydrocarbons of mineral origin, and pesticide residues can largely be removed by refining. For many years, this Food Safety Assurance System has proven to be effective in controlling contaminant levels in refined vegetable oils and fats.

Hirshfeld atom refinement for modelling strong hydrogen bonds.

Science.gov (United States)

Woińska, Magdalena; Jayatilaka, Dylan; Spackman, Mark A; Edwards, Alison J; Dominiak, Paulina M; Woźniak, Krzysztof; Nishibori, Eiji; Sugimoto, Kunihisa; Grabowsky, Simon

2014-09-01

High-resolution low-temperature synchrotron X-ray diffraction data of the salt L-phenylalaninium hydrogen maleate are used to test the new automated iterative Hirshfeld atom refinement (HAR) procedure for the modelling of strong hydrogen bonds. The HAR models used present the first examples of Z' > 1 treatments in the framework of wavefunction-based refinement methods. L-Phenylalaninium hydrogen maleate exhibits several hydrogen bonds in its crystal structure, of which the shortest and the most challenging to model is the O-H...O intramolecular hydrogen bond present in the hydrogen maleate anion (O...O distance is about 2.41 Å). In particular, the reconstruction of the electron density in the hydrogen maleate moiety and the determination of hydrogen-atom properties [positions, bond distances and anisotropic displacement parameters (ADPs)] are the focus of the study. For comparison to the HAR results, different spherical (independent atom model, IAM) and aspherical (free multipole model, MM; transferable aspherical atom model, TAAM) X-ray refinement techniques as well as results from a low-temperature neutron-diffraction experiment are employed. Hydrogen-atom ADPs are furthermore compared to those derived from a TLS/rigid-body (SHADE) treatment of the X-ray structures. The reference neutron-diffraction experiment reveals a truly symmetric hydrogen bond in the hydrogen maleate anion. Only with HAR is it possible to freely refine hydrogen-atom positions and ADPs from the X-ray data, which leads to the best electron-density model and the closest agreement with the structural parameters derived from the neutron-diffraction experiment, e.g. the symmetric hydrogen position can be reproduced. The multipole-based refinement techniques (MM and TAAM) yield slightly asymmetric positions, whereas the IAM yields a significantly asymmetric position.

Oil price scenarios and refining profitability

International Nuclear Information System (INIS)

Sweeney, B.

1993-01-01

Currently refining profitability is low because there has been an overbuilding of conversion capacity in Western Europe in the last round. Oil marketing, the chemicals business and the fundamental economy itself are at low points in their cycles which have not coincided, at least in the UK, since 1975. Against that gloomy background, it is predicted that downstream profitability will recover in the mid-1990s. Crude oil prices will remain low until the call on OPEC crude increases again and takes up the capacity which has been brought on stream in response to the Gulf War. When this happens, it is likely to trigger another price spike and another round of investment in production capacity. Environmentally driven investments in desulphurisation or emissions reduction will be poorly remunerated all the way through the value chain. Refining margins will recover when white oil demand growth tightens up the need for conversion capacity. Marketing will need to reduce the retail network overcapacity in the mature markets if it is to improve its profitability. In this period of low profitability, even with the light at the end of the tunnel for refiners in the middle of the decade, the industry structure is under threat. There is a strong argument for new modes of competitive behaviour which are backed by strong elements of cooperation. (author)

Influences of different degassing processes on refining effect and properties of 4004 Al alloy

Directory of Open Access Journals (Sweden)

Wang Liping

2013-03-01

Full Text Available In order to improve the plasticity of 4004 Al alloy and subsequently the productivity of 4004 Al foil, the research studied in detail the influence of the rotary impeller degassing process on the refining effect of 4004 Al alloy, in which the impacts of four major parameters: gas flow, rotational speed, refining time, and stewing time, on degassing rate of 4004 Al alloy was systematically studied by using an orthogonal experiment methodology. Results show that the rotational speed has the greatest impact on the degassing of 4004 Al alloy, followed by gas flow and refining time; stewing time has the least impact. The optimum purification parameters obtained by current orthogonal analysis were: rotor speed of 500 r·min-1, inert gas flow of 0.4 mL·h-1, refining time of 15 min, and stewing time of 6 min. Degassing rate using the optimum parameters reaches 68%. In addition, the comparison experiments among C2Cl6 refining, rotary impeller degassing, and combined treatment of C2Cl6 refining and rotary impeller degassing for 4004 Al alloy were performed. The experimental data indicated that the combined treatment of C2Cl6 refining and rotary impeller degassing has the best degassing effect. Degassing rate of C2Cl6 refining, rotary impeller degassing and combined refining treatment is 39%, 69.1% and 76.9%, respectively. The mechanical properties of the specimen refined by rotary impeller degassing were higher than those by C2Cl6 refining, but lower than those by combined refining treatment.

The Analysis of the Refined Financial Management of Modern Enterprises

Directory of Open Access Journals (Sweden)

Li Ran

2016-01-01

Full Text Available This paper briefly introduces the concept of the refined financial management, elaborates on its characteristics and puts forward some main points about it. It also comes up with some personal suggestions for reference on effective ways of refining financial management.

TRIPOLI I: energy-dependent three-dimensional Monte Carlo Program. Volume I. Conception and presentation of the TRIPOLI I System

International Nuclear Information System (INIS)

Katz, S.; Nimal, J.C.

In its present version TRIPOLI/1/ is an energy dependent three-dimensional program which treats the slowing down and diffusion of neutrons for source problems. The version presented here is essentially oriented towards reactor shielding problems. It is written in FORTRAN for IBM (series 360) computer. This volume is devoted to a summary of the essential characteristics of the program as well as to a description of the constants required for the description of the chaining together of the work to be carried out

View from the market : the refiners' perspective

International Nuclear Information System (INIS)

Earnest, N.K.

2003-01-01

The western Canadian crude market area is vast, ranging from Puget Sound to Oklahoma to western Pennsylvania. The three main challenges facing western Canadian crude oil producers are high crude production volumes of heavy sour grades, strong competition for market share from the United States and offshore crudes, and the inability to access offshore global crude markets in meaningful volumes. The paper includes a map depicting core markets which have historically processed most of the crude produced in western Canada. The map also includes extended market areas where western Canadian crude sales are expected to increase as production increases. These regions will become the price setting areas for Canadian crude. Currently more than 40 per cent of the total crude produced in western Canada flows into the upper Midwest market. This paper summarized Canadian crude pricing mechanisms, noting that more than half of the oil consumed in North America is imported, linking North America with the pricing dynamics and supply/demand considerations of the global crude markets. The two key points that have to be considered in the Canadian crude pricing mechanisms is the economics of refining and parity point location. Crude grades such as light sweet or medium sour, are priced relative to one another depending on their differing values as a feedstock. The greatest determinant of relative crude grade value is the proportion produced of high value, light transportation fuels compared to low value, heavy products such as asphalt and heavy fuel oil. The value of crude oil is also influenced by the level of sulphur and metal content. A section of the paper was devoted to the pricing of heavy sour conventional and bitumen blend crudes, which is different than for lighter crude grades because of the near lack of competition from similar imported crude grades. A market optimization model used to analyze the future price relationships for Canadian crudes showed that the Canadian crude

Statistics Anxiety Update: Refining the Construct and Recommendations for a New Research Agenda.

Science.gov (United States)

Chew, Peter K H; Dillon, Denise B

2014-03-01

Appreciation of the importance of statistics literacy for citizens of a democracy has resulted in an increasing number of degree programs making statistics courses mandatory for university students. Unfortunately, empirical evidence suggests that students in nonmathematical disciplines (e.g., social sciences) regard statistics courses as the most anxiety-inducing course in their degree programs. Although a literature review exists for statistics anxiety, it was done more than a decade ago, and newer studies have since added findings for consideration. In this article, we provide a current review of the statistics anxiety literature. Specifically, related variables, definitions, and measures of statistics anxiety are reviewed with the goal of refining the statistics anxiety construct. Antecedents, effects, and interventions of statistics anxiety are also reviewed to provide recommendations for statistics instructors and for a new research agenda. © The Author(s) 2014.

Process for refining hydrocarbons

Energy Technology Data Exchange (ETDEWEB)

Risenfeld, E H

1924-11-26

A process is disclosed for the refining of hydrocarbons or other mixtures through treatment in vapor form with metal catalysts, characterized by such metals being used as catalysts, which are obtained by reduction of the oxide of minerals containing the iron group, and by the vapors of the hydrocarbons, in the presence of the water vapor, being led over these catalysts at temperatures from 200 to 300/sup 0/C.

NASA Aerospace Flight Battery Program: Wet Life of Nickel-Hydrogen (Ni-H2) Batteries. Volume 1, Part 3

Science.gov (United States)

Jung, David S.; Lee, Leonine S.; Manzo, Michelle A.

2010-01-01

This NASA Aerospace Flight Battery Systems Working Group was chartered within the NASA Engineering and Safety Center (NESC). The Battery Working Group was tasked to complete tasks and to propose proactive work to address battery related, agency-wide issues on an annual basis. In its first year of operation, this proactive program addressed various aspects of the validation and verification of aerospace battery systems for NASA missions. Studies were performed, issues were discussed and in many cases, test programs were executed to generate recommendations and guidelines to reduce risk associated with various aspects of implementing battery technology in the aerospace industry. This document contains Part 3 - Volume I: Wet Life of Nickel-Hydrogen (Ni-H2) Batteries of the program's operations.

National Low-Level Waste Management Program radionuclide report series. Volume 2, Niobium-94

International Nuclear Information System (INIS)

Adams, J.P.; Carboneau, M.L.

1995-04-01

The Purpose of the National Low-Level Waste Management Program Radionuclide Report Series is to provide information to, state representatives and developers of low-level radioactive waste disposal facilities about the radiological chemical, and physical characteristics of selected radionuclides and their behavior in the low-level radioactive waste disposal facility environment. Extensive surveys of available literature provided information used to produce this series of reports and an introductory report. This report is Volume 11 of the series. It outlines the basic radiological, chemical, and physical characteristics of niobium-94, waste types and forms that contain it, and its behavior in environmental media such as soils, plants, groundwater, air, animals and the human body

Investment in exploration-production and refining 2014

International Nuclear Information System (INIS)

Hureau, Geoffroy; Serbutoviez, Sylvain; Silva, Constancio; Maisonnier, Guy

2014-11-01

IFPEN analyses in this study the 2014 evolution of global investment in the field of exploration-production and refining: 1 - Changes in oil and gas prices: General background: weak economy and global disorder, Oil prices: fundamentals that could help to relax oil prices?, Gas prices: fall in Europe, stability in Japan, increase in the US; 2 - Exploration and production - Slowdown in growth: moderate rise in investment in 2014, exploration - Discoveries in 2014, Russia: sanctions will have limited short term impact, implications of the reforms to the Mexican energy sector; 3 - Drilling activity and market throughout the world: onshore and offshore drilling (Number of wells drilled throughout the world, Number of onshore wells, Number of offshore wells, Drilling, equipment and well services markets, Onshore drilling market, Offshore drilling market, Fracking market), Geophysical activity and the geophysical market, Offshore construction activity and the offshore construction market (Offshore construction activities, Rig construction activity, Floating Platform Systems (FPS), Sub-sea constructions, Offshore construction market); 4 - Refining - Significant increase in spending: increase in industrial costs, a slowdown in the increase in excess capacity in the future?, A bleak future for the european refining sector

P-Refinement and P-Threads (Preprint)

National Research Council Canada - National Science Library

Dong, Steven; Karniadakis, George E

2002-01-01

...]) in d dimensions, which is higher than lower-order methods. In this paper, we demonstrate that by employing multi-threading within MPI processes we manage to counter- balance the cost increase associated with P-refinement...

Dedicated Perioperative Hip Fracture Comanagement Programs are Cost-effective in High-volume Centers: An Economic Analysis.

Science.gov (United States)

Swart, Eric; Vasudeva, Eshan; Makhni, Eric C; Macaulay, William; Bozic, Kevin J

2016-01-01

Osteoporotic hip fractures are common injuries typically occurring in patients who are older and medically frail. Studies have suggested that creation of a multidisciplinary team including orthopaedic surgeons, internal medicine physicians, social workers, and specialized physical therapists, to comanage these patients can decrease complication rates, improve time to surgery, and reduce hospital length of stay; however, they have yet to achieve widespread implementation, partly owing to concerns regarding resource requirements necessary for a comanagement program. We performed an economic analysis to determine whether implementation of a comanagement model of care for geriatric patients with osteoporotic hip fractures would be a cost-effective intervention at hospitals with moderate volume. We also calculated what annual volume of cases would be needed for a comanagement program to "break even", and finally we evaluated whether universal or risk-stratified comanagement was more cost effective. Decision analysis techniques were used to model the effect of implementing a systems-based strategy to improve inpatient perioperative care. Costs were obtained from best-available literature and included salary to support personnel and resources to expedite time to the operating room. The major economic benefit was decreased initial hospital length of stay, which was determined via literature review and meta-analysis, and a health benefit was improvement in perioperative mortality owing to expedited preoperative evaluation based on previously conducted meta-analyses. A break-even analysis was conducted to determine the annual case volume necessary for comanagement to be either (1) cost effective (improve health-related quality of life enough to be worth additional expenses) or (2) result in cost savings (actually result in decreased total expenses). This calculation assumed the scenario in which a hospital could hire only one hospitalist (and therapist and social worker) on

International Nuclear Model. Volume 3. Program description. Appendix A-H (Part 1)

International Nuclear Information System (INIS)

Andress, D.

1985-01-01

The International Nuclear Model (INM) is a comprehensive model of the commercial nuclear power industry. It simulates economic decisions for reactor deployment and fuel management decisions based on an input set of technical, economic and scenario parameters. The technical parameters include reactor operating characteristics, fuel cycle timing and mass loss factors, and enrichment tails assays. Economic parameters include fuel cycle costs, financial data, and tax alternatives. INM has a broad range of scenario options covering, for example, process constraints, interregional activities, reprocessing, and fuel management selection. INM reports reactor deployment schedules, electricity generation, and fuel cycle requirements and costs. It also has specialized reports for extended burnup and permanent disposal. This volume contains appendices A through H including a description of subroutines and the Fortran listing of the program

Carcinogenicity of petroleum lubricating oil distillates: effects of solvent refining, hydroprocessing, and blending.

Science.gov (United States)

Halder, C A; Warne, T M; Little, R Q; Garvin, P J

1984-01-01

Certain refining processes were investigated to determine their influence on the dermal carcinogenic activity of petroleum-derived lubricating oil distillates. Specifically, the effects of solvent refining, hydroprocessing, a combination of both processes, and the blending of oils processed using each technique were evaluated in standard mouse skin-painting bioassays. The refining process used as well as the level or severity of treatment greatly influenced the carcinogenic outcome of processed lubricating oils. Solvent refining at severities normally used appeared to eliminate carcinogenicity. In contrast, hydroprocessing alone at mild levels of treatment was successful only in reducing the carcinogenic potency; severe hydroprocessing conditions were necessary to eliminate carcinogenic activity without the use of additional refining processes. Carcinogenic activity could also be eliminated by following moderate solvent refining with mild hydroprocessing. Blending of hydroprocessed oils with solvent-refined oils resulted in a substantial reduction or even elimination of carcinogenic activity. However, the degree of protection obtained varied with the particular distillates used and appeared largely dependent on the inherent biological activity of the hydroprocessed oil.

Refining in the 1990's: Restructuring and resurgence

International Nuclear Information System (INIS)

Cobb, C.B.

1994-01-01

After two years of uncertainty in dealing with the 1990 Clean Air Act Amendments coupled with the shutdown of 5% of total US refining capacity, the industry is now positioning itself for continued operations throughout the remainder of the decade. However, refineries are experiencing a shift in the mode of operations to a period of more restructuring (closings, ventures, alliances, etc.) followed by a resurgence in financial performance. The purpose of this paper is to examine the current industry and highlight the reasons for industry's current plans. The authors also speculate about the strategies companies will choose to better their financial performance. Fundamentally, the characteristics of a mature domestic business remain the driving force that shape decision making. In responding to the maturing of refining, the authors suggest that refiners will change the way they conduct business over the next few years. Building on the theme of the 1993 NPRA paper, strategies will target the domestic side of the business while simultaneously shifting to a global perspective

Assume-Guarantee Abstraction Refinement Meets Hybrid Systems

Science.gov (United States)

Bogomolov, Sergiy; Frehse, Goran; Greitschus, Marius; Grosu, Radu; Pasareanu, Corina S.; Podelski, Andreas; Strump, Thomas

2014-01-01

Compositional verification techniques in the assume- guarantee style have been successfully applied to transition systems to efficiently reduce the search space by leveraging the compositional nature of the systems under consideration. We adapt these techniques to the domain of hybrid systems with affine dynamics. To build assumptions we introduce an abstraction based on location merging. We integrate the assume-guarantee style analysis with automatic abstraction refinement. We have implemented our approach in the symbolic hybrid model checker SpaceEx. The evaluation shows its practical potential. To the best of our knowledge, this is the first work combining assume-guarantee reasoning with automatic abstraction-refinement in the context of hybrid automata.

India beckons participants in burgeoning refining sector

International Nuclear Information System (INIS)

Anon.

1992-01-01

This paper reports that India has opened its refining sector to full private investment for the first time in more than 2 decades. The government again gave a green light to construction of three 120,000 b/d grassroots refineries in East, West, and Central India. The projects had won various governmental approvals in the past few years, but never moved off high center for a variety of economic and regulatory reasons. The difference this time is that the government is offering interests in the projects to private foreign and domestic investors. It's part of India's push to boost overall refining capacity by more than 80% this century

Macromolecular refinement by model morphing using non-atomic parameterizations.

Science.gov (United States)

Cowtan, Kevin; Agirre, Jon

2018-02-01

Refinement is a critical step in the determination of a model which explains the crystallographic observations and thus best accounts for the missing phase components. The scattering density is usually described in terms of atomic parameters; however, in macromolecular crystallography the resolution of the data is generally insufficient to determine the values of these parameters for individual atoms. Stereochemical and geometric restraints are used to provide additional information, but produce interrelationships between parameters which slow convergence, resulting in longer refinement times. An alternative approach is proposed in which parameters are not attached to atoms, but to regions of the electron-density map. These parameters can move the density or change the local temperature factor to better explain the structure factors. Varying the size of the region which determines the parameters at a particular position in the map allows the method to be applied at different resolutions without the use of restraints. Potential applications include initial refinement of molecular-replacement models with domain motions, and potentially the use of electron density from other sources such as electron cryo-microscopy (cryo-EM) as the refinement model.

Horn clause verification with convex polyhedral abstraction and tree automata-based refinement

DEFF Research Database (Denmark)

Kafle, Bishoksan; Gallagher, John Patrick

2017-01-01

In this paper we apply tree-automata techniques to refinement of abstract interpretation in Horn clause verification. We go beyond previous work on refining trace abstractions; firstly we handle tree automata rather than string automata and thereby can capture traces in any Horn clause derivations...... underlying the Horn clauses. Experiments using linear constraint problems and the abstract domain of convex polyhedra show that the refinement technique is practical and that iteration of abstract interpretation with tree automata-based refinement solves many challenging Horn clause verification problems. We...... compare the results with other state-of-the-art Horn clause verification tools....

Refining capacity in Quebec : the Quebec market, industry viewpoint

International Nuclear Information System (INIS)

Trudelle, F.

2004-01-01

Canada's second largest oil refinery is operated by Ultramar Ltd. in Levis, Quebec. The refinery, which supplies 45 per cent of all Quebec's petroleum, distributes its products to Quebec, Ontario and the Maritime provinces. The refinery currently produces 215,000 barrels per day. Ultramar is a division of Valero, an American firm which has a total refining capacity of 2.4 million barrels per day. A summary of the company's petroleum energy distribution, consumption, and reserves was presented and compared with the national and global position. It was noted that world demand for petroleum products increases yearly by 1 to 1.5 per cent while the demand for automobile fuel in North America increases by 2.5 to 3.5 per cent. In the last 10 years, world demand has increased by more than 22 per cent but refining capacity has only increased by 12 per cent. The average profitability of the refining industry from 1992 to 2002 was approximately 5.5 per cent, which limited investments in new refinery installations. Much of the industry's profits have been utilized to modify installations in order to reduce the sulphur content in gasoline and diesel fuels. Furthermore, the obtention of permits to construct new refining installations has become a major obstacle and the ratification of the Kyoto Protocol may signify a 30 per cent reduction in automotive fuel demand. Given this, there is currently some hesitation and uncertainty by the refining industry to proceed with new major installations. tabs., figs

Department of Energy Programmatic Spent Nuclear Fuel Management and Idaho National Engineering Laboratory Environmental Restoration and Waste Management Programs draft environmental impact statement. Volume 1, Appendix B: Idaho National Engineering Laboratory Spent Nuclear Fuel Management Program

Energy Technology Data Exchange (ETDEWEB)

1994-06-01

The US Department of Energy (DOE) has prepared this report to assist its management in making two decisions. The first decision, which is programmatic, is to determine the management program for DOE spent nuclear fuel. The second decision is on the future direction of environmental restoration, waste management, and spent nuclear fuel management activities at the Idaho National Engineering Laboratory. Volume 1 of the EIS, which supports the programmatic decision, considers the effects of spent nuclear fuel management on the quality of the human and natural environment for planning years 1995 through 2035. DOE has derived the information and analysis results in Volume 1 from several site-specific appendixes. Volume 2 of the EIS, which supports the INEL-specific decision, describes environmental impacts for various environmental restoration, waste management, and spent nuclear fuel management alternatives for planning years 1995 through 2005. This Appendix B to Volume 1 considers the impacts on the INEL environment of the implementation of various DOE-wide spent nuclear fuel management alternatives. The Naval Nuclear Propulsion Program, which is a joint Navy/DOE program, is responsible for spent naval nuclear fuel examination at the INEL. For this appendix, naval fuel that has been examined at the Naval Reactors Facility and turned over to DOE for storage is termed naval-type fuel. This appendix evaluates the management of DOE spent nuclear fuel including naval-type fuel.

BASIC program to compute uranium density and void volume fraction in laboratory-scale uranium silicide aluminum dispersion plate-type fuel

International Nuclear Information System (INIS)

Ugajin, Mitsuhiro

1991-05-01

BASIC program simple and easy to operate has been developed to compute uranium density and void volume fraction for laboratory-scale uranium silicide aluminum dispersion plate-type fuel, so called miniplate. An example of the result of calculation is given in order to demonstrate how the calculated void fraction correlates with the microstructural distribution of the void in a miniplate prepared in our laboratory. The program is also able to constitute data base on important parameters for miniplates from experimentally-determined values of density, weight of each constituent and dimensions of miniplates. Utility programs pertinent to the development of the BASIC program are also given which run in the popular MS-DOS environment. All the source lists are attached and brief description for each program is made. (author)

Thermosphere-ionosphere-mesosphere energetics and dynamics (TIMED). The TIMED mission and science program report of the science definition team. Volume 1: Executive summary

Science.gov (United States)

1991-01-01

A Science Definition Team was established in December 1990 by the Space Physics Division, NASA, to develop a satellite program to conduct research on the energetics, dynamics, and chemistry of the mesosphere and lower thermosphere/ionosphere. This two-volume publication describes the TIMED (Thermosphere-Ionosphere-Mesosphere, Energetics and Dynamics) mission and associated science program. The report outlines the scientific objectives of the mission, the program requirements, and the approach towards meeting these requirements.

User's guide for PRISIM (Plant Risk Status Information Management System) Arkansas Nuclear One--Unit 1: Volume 2, Program for regulators

Energy Technology Data Exchange (ETDEWEB)

Campbell, D.J.; Guthrie, V.H.; Kirchner, J.R.; Kirkman, J.Q.; Paula, H.M.; Ellison, B.C.; Dycus, F.M.; Farquharson, J.A.; Flanagan, G.F.

1988-03-01

This user's guide is a two-volume document designed to teach NRC inspectors and NRC regulators how to access probabilistic risk assessment information from the two Plant Risk Status Information Management System (PRISIM) programs developed for Arkansas Nuclear One--Unit One (ANA-1). This document, Volume 2, describes how the PRA information available in Version 2.0 of PRISIM is useful as an evaluation tool for regulatory activities. Using PRISIM is useful as an evaluation tool for regulatory activities. Using PRISIM, regulators can both access PRA information and modify the information to assess the impact these changes may have on plant safety. Each volume is a stand-alone document.

Report on the analysis of the quality assurance and quality control data for the petroleum refining sector

International Nuclear Information System (INIS)

Thorton, N.; Michajluk, S.; Powell, T.; Lee, G.

1992-07-01

The Ontario Municipal-Industrial Strategy for Abatement (MISA) program has the ultimate goal of virtual elimination of persistent toxic contaminants from all discharges to provincial waterways. MISA effluent monitoring regulations, first promulgated for the petroleum refining sector, require direct dischargers to monitor their effluents for a specified number of contaminants and a specified frequency over a one-year period. The refineries were also required to carry out a quality control program on all process effluent streams and for specified analytical test groups. Two types of quality assurance/quality control (QA/QC) data were required: field QA/QC, which would indicate problems with field contamination or sampling, and laboratory QA/QC, which would indicate problems with the laboratory. The objectives of QA/QC analysis are to identify the significance of biases, chronic contamination, data variability, and false results, to assess data validity, and to allow data comparability among companies and laboratories. Of the 149 parameters monitored in the petroleum refining sector, 34 qualified as candidates for setting effluent limits. The QA/QC evaluation of monitoring data for the 34 parameters confirmed the presence of 18 parameters at such levels that they could be used to set statistically valid quantitative limits. 50 tabs

NOMAD-Ref: visualization, deformation and refinement of macromolecular structures based on all-atom normal mode analysis.

Science.gov (United States)

Lindahl, Erik; Azuara, Cyril; Koehl, Patrice; Delarue, Marc

2006-07-01

Normal mode analysis (NMA) is an efficient way to study collective motions in biomolecules that bypasses the computational costs and many limitations associated with full dynamics simulations. The NOMAD-Ref web server presented here provides tools for online calculation of the normal modes of large molecules (up to 100,000 atoms) maintaining a full all-atom representation of their structures, as well as access to a number of programs that utilize these collective motions for deformation and refinement of biomolecular structures. Applications include the generation of sets of decoys with correct stereochemistry but arbitrary large amplitude movements, the quantification of the overlap between alternative conformations of a molecule, refinement of structures against experimental data, such as X-ray diffraction structure factors or Cryo-EM maps and optimization of docked complexes by modeling receptor/ligand flexibility through normal mode motions. The server can be accessed at the URL http://lorentz.immstr.pasteur.fr/nomad-ref.php.

Refining mineral oils

Energy Technology Data Exchange (ETDEWEB)

1946-07-05

A process is described refining raw oils such as mineral oils, shale oils, tar, their fractions and derivatives, by extraction with a selected solvent or a mixture of solvents containing water, forming a solvent more favorable for the hydrocarbons poor in hydrogen than for hydrocarbons rich in hydrogen, this process is characterized by the addition of an aiding solvent for the water which can be mixed or dissolved in the water and the solvent or in the dissolving mixture and increasing in this way the solubility of the water in the solvent or the dissolving mixture.

Assessing food allergy risks from residual peanut protein in highly refined vegetable oil

NARCIS (Netherlands)

Blom, W.M.; Kruizinga, A.G.; Rubingh, C.M.; Remington, B.C.; Crevel, R.W.R.; Houben, G.F.

2017-01-01

Refined vegetable oils including refined peanut oil are widely used in foods. Due to shared production processes, refined non-peanut vegetable oils can contain residual peanut proteins. We estimated the predicted number of allergic reactions to residual peanut proteins using probabilistic risk

User's guide for PRISM (Plant Risk Status Information Management System) Arkansas Nuclear One-Unit 1: Volume 1, Program for inspectors

Energy Technology Data Exchange (ETDEWEB)

Campbell, D.J.; Guthrie, V.H.; Kirchner, J.R.; Kirkman, J.Q.; Paula, H.M.; Ellison, B.C.; Dycus, F.M.; Farquharson, J.A.; Flanagan, G.F.

1988-03-01

This user's guide is a two-volume document designed to teach NRC inspectors and NRC regulators how to access probabilistic risk assessment information from the two Plant Risk Status Information Management System (PRISIM) programs developed for Arkansas Nuclear One -- Unit One (ANO-1). This document, Volume 1, describes how the PRA information available in Version 1.0 of PRISIM is useful for planning inspections. Using PRISIM, inspectors can quickly access PRA information and use that information to update risk analysis results, reflecting a plant's status at any particular time. Both volumes are stand-alone documents, and each volume presents several sample computer sessions designed to lead the user through a variety of PRISIM applications used to obtain PRA-related information for monitoring and controlling plant risk.

The changing face of U.S. refining: Ominous notes

International Nuclear Information System (INIS)

Anon.

1992-01-01

As environmental protection comes of age in the US, a complex series of structural changes is also expected - in enforcement bureaucracy, manufacturing, and in energy consumption. It is already quite obvious in the petroleum refining industry. A side effect may be the export of jobs. Buyouts and closures are expected, as is increased refined product import dependency. This issue updates expected changes in gasoline and distillate product requirements in the US, and reports some ominous statements from some of the oil industry's affected parties. This issue also presented the following: (1) the ED Refining Netback Data Series for the US Gulf and West Coasts, Rotterdam, and Singapore as of Jan. 24, 1992; and (2) the ED Fuel Price Tax Series for countries of the Eastern Hemisphere, Jan. 1992 edition

Taiwan: refined need for consuming population

International Nuclear Information System (INIS)

Hayes, David.

1995-01-01

A brief discussion is given of the oil and gas industry in Taiwan. Topics covered include the possibility of privatization, refineries and refining contracts overseas, plans for a new petrochemical complex and an offshore submarine transmission pipeline. (UK)

Effect of some grain refiners on the mechanical properties of aluminum

International Nuclear Information System (INIS)

Zaid, A.I.O.

2001-01-01

It is well established that aluminum and its alloys are grain refined by some refractory metals to enhance their surface qualities and mechanical strengths. In this paper, the literature on grain refining, and its mechanism is reviewed and discussed. Also, the effect of grain refining of commercially pure aluminum by the addition of titanium, boron, vanadium, molybdenum, and zirconium is investigated. The effect of each of these elements on grain size, hardness and mechanical behavior is presented and discussed. It was found that the addition of any of these elements except zirconium resulted in enhancement of grain size, hardness and mechanical strength. An increase of 2.1 % in flow stress of Al grain refined by Ti+B was achieved by addition of 0.1 % V at 0.2 strain. (author)

Refined 3d-3d correspondence

Energy Technology Data Exchange (ETDEWEB)

Alday, Luis F.; Genolini, Pietro Benetti; Bullimore, Mathew; Loon, Mark van [Mathematical Institute, University of Oxford, Andrew Wiles Building,Radcliffe Observatory Quarter, Woodstock Road, Oxford, OX2 6GG (United Kingdom)

2017-04-28

We explore aspects of the correspondence between Seifert 3-manifolds and 3d N=2 supersymmetric theories with a distinguished abelian flavour symmetry. We give a prescription for computing the squashed three-sphere partition functions of such 3d N=2 theories constructed from boundary conditions and interfaces in a 4d N=2{sup ∗} theory, mirroring the construction of Seifert manifold invariants via Dehn surgery. This is extended to include links in the Seifert manifold by the insertion of supersymmetric Wilson-’t Hooft loops in the 4d N=2{sup ∗} theory. In the presence of a mass parameter for the distinguished flavour symmetry, we recover aspects of refined Chern-Simons theory with complex gauge group, and in particular construct an analytic continuation of the S-matrix of refined Chern-Simons theory.

Heavy Truck Engine Program

Energy Technology Data Exchange (ETDEWEB)

Nelson, Christopher

2009-01-08

The Heavy Duty Truck Engine Program at Cummins embodied three significant development phases. All phases of work strove to demonstrate a high level of diesel engine efficiency in the face of increasingly stringent emission requirements. Concurrently, aftertreatment system development and refinement was pursued in support of these efficiency demonstrations. The program's first phase focused on the demonstration in-vehicle of a high level of heavy duty diesel engine efficiency (45% Brake Thermal Efficiency) at a typical cruise condition while achieving composite emissions results which met the 2004 U.S. EPA legislated standards. With a combination of engine combustion calibration tuning and the development and application of Urea-based SCR and particulate aftertreatment, these demonstrations were successfully performed by Q4 of 2002. The second phase of the program directed efforts towards an in-vehicle demonstration of an engine system capable of meeting 2007 U.S. EPA legislated emissions requirements while achieving 45% Brake Thermal Efficiency at cruise conditions. Through further combustion optimization, the refinement of Cummins Cooled EGR architecture, the application of a high pressure common rail fuel system and the incorporation of optimized engine parasitics, Cummins Inc. successfully demonstrated these deliverables in Q2 of 2004. The program's final phase set a stretch goal of demonstrating 50% Brake Thermal Efficiency from a heavy duty diesel engine system capable of meeting 2010 U.S. EPA legislated emissions requirements. Cummins chose to pursue this goal through further combustion development and refinement of the Cooled EGR system architecture and also applied a Rankine cycle Waste Heat Recovery technique to convert otherwise wasted thermal energy to useful power. The engine and heat recovery system was demonstrated to achieve 50% Brake Thermal Efficiency while operating at a torque peak condition in second quarter, 2006. The 50% efficient

Using atomic energy in the oil refining and petrochemical industry

Energy Technology Data Exchange (ETDEWEB)

Feigin, E.A.; Barashkov, R.Ia.; Raud, E.A.

1982-01-01

A short description of the basic large scale processes for oil refining and petrochemistry in which nuclear reactors can be used is given. The possible industrial plans for using nuclear reactors are examined together with the problems in using the advances in atomic technology in oil refining and petrochemical processes.

Repetitive Identification of Structural Systems Using a Nonlinear Model Parameter Refinement Approach

Directory of Open Access Journals (Sweden)

Jeng-Wen Lin

2009-01-01

Full Text Available This paper proposes a statistical confidence interval based nonlinear model parameter refinement approach for the health monitoring of structural systems subjected to seismic excitations. The developed model refinement approach uses the 95% confidence interval of the estimated structural parameters to determine their statistical significance in a least-squares regression setting. When the parameters' confidence interval covers the zero value, it is statistically sustainable to truncate such parameters. The remaining parameters will repetitively undergo such parameter sifting process for model refinement until all the parameters' statistical significance cannot be further improved. This newly developed model refinement approach is implemented for the series models of multivariable polynomial expansions: the linear, the Taylor series, and the power series model, leading to a more accurate identification as well as a more controllable design for system vibration control. Because the statistical regression based model refinement approach is intrinsically used to process a “batch” of data and obtain an ensemble average estimation such as the structural stiffness, the Kalman filter and one of its extended versions is introduced to the refined power series model for structural health monitoring.

Refining borders of genome-rearrangements including repetitions

Directory of Open Access Journals (Sweden)

JA Arjona-Medina

2016-10-01

Full Text Available Abstract Background DNA rearrangement events have been widely studied in comparative genomic for many years. The importance of these events resides not only in the study about relatedness among different species, but also to determine the mechanisms behind evolution. Although there are many methods to identify genome-rearrangements (GR, the refinement of their borders has become a huge challenge. Until now no accepted method exists to achieve accurate fine-tuning: i.e. the notion of breakpoint (BP is still an open issue, and despite repeated regions are vital to understand evolution they are not taken into account in most of the GR detection and refinement methods. Methods and results We propose a method to refine the borders of GR including repeated regions. Instead of removing these repetitions to facilitate computation, we take advantage of them using a consensus alignment sequence of the repeated region in between two blocks. Using the concept of identity vectors for Synteny Blocks (SB and repetitions, a Finite State Machine is designed to detect transition points in the difference between such vectors. The method does not force the BP to be a region or a point but depends on the alignment transitions within the SBs and repetitions. Conclusion The accurate definition of the borders of SB and repeated genomic regions and consequently the detection of BP might help to understand the evolutionary model of species. In this manuscript we present a new proposal for such a refinement. Features of the SBs borders and BPs are different and fit with what is expected. SBs with more diversity in annotations and BPs short and richer in DNA replication and stress response, which are strongly linked with rearrangements.

Chemical sensitive interfacial free volume studies of nanophase Al-rich alloys

International Nuclear Information System (INIS)

Lechner, W.; Puff, W.; Wuerschum, R.; Wilde, G.

2006-01-01

Full text: Al-based nanocrystalline alloys have attracted substantial interest due to their outstanding mechanical properties. These alloys can be obtained by crystallization of melt-spun amorphous precursors or by grain refinement upon repeated cold-rolling of elemental layers. For both synthesis routes, the nanocrystallization process is sensitively affected by interfacial chemistry and free volumes. In order to contribute to an atomistic understanding of the interfacial structure and processes during nanocrystallization, the present work deals with studies of interfacial free volumes by means of positron-annihilation-spectroscopy. In addition to positron lifetime spectroscopy which yields information on the size of free volumes, coincident Doppler broadening of the positron-electron annihilation photons is applied as novel technique for studying the chemistry of interfaces in nanophase materials on an atomistic scale. Al-rich alloys of the above mentioned synthesis routes were studied in this work. (author)

Grain refinement of AZ31 by (SiC)P: Theoretical calculation and experiment

International Nuclear Information System (INIS)

Guenther, R.; Hartig, Ch.; Bormann, R.

2006-01-01

Grain refinement of gravity die-cast Mg-alloys can be achieved via two methods: in situ refinement by primary precipitated metallic or intermetallic phases, and inoculation of the melt via ceramic particles that remain stable in the melt due to their high thermodynamic stability. In order to clarify grain refinement mechanisms and optimize possible potent refiners in Mg-alloys, a simulation method for heterogeneous nucleation based on a free growth model has been developed. It allows the prediction of the grain size as a function of the particle size distribution, the volumetric content of ceramic inoculants, the cooling rate and the alloy constitution. The model assumptions were examined experimentally by a study of the grain refinement of (SiC) P in AZ31. Additions of (SiC) P result in significant grain refinement, if appropriate parameters for ceramic particles are chosen. The model makes quantitatively correct predictions for the grain size and its variation with cooling rate

Process for refining shale bitumen

Energy Technology Data Exchange (ETDEWEB)

Plauson, H

1920-09-19

A process is disclosed for refining shale bitumen for use as heavy mineral oil, characterized by mixtures of blown hard shale pitch and heavy mineral oil being blown with hot air at temperatures of 120 to 150/sup 0/ with 1 to 3 percent sulfur, and if necessary with 0.5 to 3 percent of an aldehyde.

Multigrid for refined triangle meshes

Energy Technology Data Exchange (ETDEWEB)

Shapira, Yair

1997-02-01

A two-level preconditioning method for the solution of (locally) refined finite element schemes using triangle meshes is introduced. In the isotropic SPD case, it is shown that the condition number of the preconditioned stiffness matrix is bounded uniformly for all sufficiently regular triangulations. This is also verified numerically for an isotropic diffusion problem with highly discontinuous coefficients.

Unit-cell refinement from powder diffraction scans

International Nuclear Information System (INIS)

Pawley, G.S.

1981-01-01

A procedure for the refinement of the crystal unit cell from a powder diffraction scan is presented. In this procedure knowledge of the crystal structure is not required, and at the end of the refinement a list of indexed intensities is produced. This list may well be usable as the starting point for the application of direct methods. The problems of least-squares ill-conditioning due to overlapping reflections are overcome by constraints. An example using decafluorocyclohexene, C 6 F 10 , shows the quality of fit obtained in a case which may even be a false minimum. The method should become more relevant as powder scans of improved resolution become available, through the use of pulsed neutron sources. (Auth.)

Refining crude oils and gasolines, etc

Energy Technology Data Exchange (ETDEWEB)

1931-11-23

A process of refining crude oils and gasolines distilled from shale and the like is described, consisting of submitting them to a prewash with soda, an oxidation preferably with hypochlorite solution, a hydrogenation with nascent hydrogen, and finally rectification and neutralization.

Southern forest inventory and analysis volume equation user’s guide

Science.gov (United States)

Christopher M. Oswalt; Roger C. Conner

2011-01-01

Reliable volume estimation procedures are fundamental to the mission of the Forest Inventory and Analysis (FIA) program. Moreover, public access to FIA program procedures is imperative. Here we present the volume estimation procedures used by the southern FIA program of the U.S. Department of Agriculture Forest Service Southern Research Station. The guide presented...

Microcomputer based program for predicting heat transfer under reactor accident conditions. Volume I

International Nuclear Information System (INIS)

Cheng, S.C.; Groeneveld, D.C.; Leung, L.K.H.; Wong, Y.L.; Nguyen, C.

1987-07-01

A microcomputer based program called Heat Transfer Prediction Software (HTPS) has been developed. It calculates the heat transfer for the tube and bundle geometries for steady state and transient conditions. This program is capable of providing the best estimated of the hot pin temperatures during slow transients for 37- and 28-element CANDU type fuel bundles. The program is designed for an IBM-PC AT/XT (or IBM-PC compatible computer) equipped with a Math Co-processor. The following input parameters are required: pressure, mass flux, hydraulic diameter, and quality. For the steady state case, the critical heat flux (CHF), the critical heat flux temperature, the minimum film boiling temperature, and the minimum film boiling heat flux are the primary outputs. With either the surface heat flux or wall temperature specified, the program determines the heat transfer regime and calculates the surface heat flux, wall temperatures and heat transfer coefficient. For the slow transient case, the pressure, mass flux, quality, and volumetric heat generation rate are the time dependent input parameters required to calculate the hot pin sheath temperatures and surface heat fluxes. A simple routine for generating properties has been developed for light water to support the above program. It contains correlations that have been verified for pressures ranging from 0.6kPa to 30 MPa, and temperatures up to 1100 degrees Celcius. The thermodynamic and transport properties that can be generated from this routine are: density, specific volume, enthalpy, specific heat capacity, conductivity, viscosity, surface tension and Prandtl number for saturated liquid, saturated vapour, subcooled liquid for superheated vapour. A software for predicting flow regime has also been developed. It determines the flow pattern at specific flow conditions, and provides a correction factor for calculating the CHF during partially stratified horizontal flow. The technical bases for the program and its

Microcomputer based program for predicting heat transfer under reactor accident conditions. Volume II

International Nuclear Information System (INIS)

Cheng, S.C.; Groeneveld, D.C.; Leung, L.K.H.; Wong, Y.L.; Nguyen, C.

1987-07-01

A microcomputer based program called Heat Transfer Prediction Software (HTPS) has been developed. It calculates the heat transfer for tube and bundle geometries for steady state and transient conditions. This program is capable of providing the best estimated of the hot pin temperatures during slow transients for 37- and 28-element CANDU type fuel bundles. The program is designed for an IBM-PC AT/XT (or IBM-PC compatible computer) equipped with a Math Co-processor. The following input parameters are required: pressure, mass flux, hydraulic diameter, and quality. For the steady state case, the critical heat flux (CHF), the critical heat flux temperature, the minimum film boiling temperature, and the minimum film boiling heat flux are the primary outputs. With either the surface heat flux or wall temperature specified, the program determines the heat transfer regime and calculates the surface heat flux, wall temperature and heat transfer coefficient. For the slow transient case, the pressure, mass flux, quality, and volumetric heat generation rate are the time dependent input parameters are required to calculate the hot pin sheath temperatures and surface heat fluxes. A simple routine for generating properties has been developed for light water to support the above program. It contains correlations that have been verified for pressures ranging from 0.6kPa to 30 MPa, and temperatures up to 1100 degrees Celcius. The thermodynamic and transport properties that can be generated from this routine are: density, specific volume, enthalpy, specific heat capacity, conductivity, viscosity, surface tension and Prandtle number for saturated liquid, saturated vapour, subcooled liquid of superheated vapour. A software for predicting flow regime has also been developed. It determines the flow pattern at specific flow conditions, and provides a correction factor for calculating the CHF during partially stratified horizontal flow. The technical bases for the program and its structure

Gulf Coast geopressured-geothermal program summary report compilation. Volume 2-A: Resource description, program history, wells tested, university and company based research, site restoration