WorldWideScience

Sample records for volume measuring system

  1. Precision volume measurement system.

    Energy Technology Data Exchange (ETDEWEB)

    Fischer, Erin E.; Shugard, Andrew D.

    2004-11-01

    A new precision volume measurement system based on a Kansas City Plant (KCP) design was built to support the volume measurement needs of the Gas Transfer Systems (GTS) department at Sandia National Labs (SNL) in California. An engineering study was undertaken to verify or refute KCP's claims of 0.5% accuracy. The study assesses the accuracy and precision of the system. The system uses the ideal gas law and precise pressure measurements (of low-pressure helium) in a temperature and computer controlled environment to ratio a known volume to an unknown volume.

  2. Development of limb volume measuring system

    Science.gov (United States)

    Bhagat, P. K.; Kadaba, P. K.

    1983-01-01

    The mechanisms underlying the reductions in orthostatic tolerance associated with weightlessness are not well established. Contradictory results from measurements of leg volume changes suggest that altered venomotor tone and reduced blood flow may not be the only contributors to orthostatic intolerance. It is felt that a more accurate limb volume system which is insensitive to environmental factors will aid in better quantification of the hemodynamics of the leg. Of the varous limb volume techniques presently available, the ultrasonic limb volume system has proven to be the best choice. The system as described herein is free from environmental effects, safe, simple to operate and causes negligible radio frequency interference problems. The segmental ultrasonic ultrasonic plethysmograph is expected to provide a better measurement of limb volume change since it is based on cross-sectional area measurements.

  3. Study of accurate volume measurement system for plutonium nitrate solution

    Energy Technology Data Exchange (ETDEWEB)

    Hosoma, T. [Power Reactor and Nuclear Fuel Development Corp., Tokai, Ibaraki (Japan). Tokai Works

    1998-12-01

    It is important for effective safeguarding of nuclear materials to establish a technique for accurate volume measurement of plutonium nitrate solution in accountancy tank. The volume of the solution can be estimated by two differential pressures between three dip-tubes, in which the air is purged by an compressor. One of the differential pressure corresponds to the density of the solution, and another corresponds to the surface level of the solution in the tank. The measurement of the differential pressure contains many uncertain errors, such as precision of pressure transducer, fluctuation of back-pressure, generation of bubbles at the front of the dip-tubes, non-uniformity of temperature and density of the solution, pressure drop in the dip-tube, and so on. The various excess pressures at the volume measurement are discussed and corrected by a reasonable method. High precision-differential pressure measurement system is developed with a quartz oscillation type transducer which converts a differential pressure to a digital signal. The developed system is used for inspection by the government and IAEA. (M. Suetake)

  4. High-speed volume measurement system and method

    Science.gov (United States)

    Lane, Michael H.; Doyle, Jr., James L.; Brinkman, Michael J.

    2015-11-24

    Disclosed is a volume sensor having first, second, and third laser sources emitting first, second, and third laser beams; first, second, and third beam splitters splitting the first, second, and third laser beams into first, second, and third beam pairs; first, second, and third optical assemblies expanding the first, second, and third beam pairs into first, second, and third pairs of parallel beam sheets; fourth, fifth, and sixth optical assemblies focusing the first, second, and third beam sheet pairs into fourth, fifth, and sixth beam pairs; and first, second, and third detector pairs receiving the fourth, fifth, and sixth beam pairs and converting a change in intensity of at least one of the beam pairs resulting from an object passing through at least one of the first, second, and third parallel beam sheets into at least one electrical signal proportional to a three-dimensional representation of the object.

  5. Single CMOS sensor system for high resolution double volume measurement applied to membrane distillation system

    Science.gov (United States)

    Lorenz, M. G.; Izquierdo-Gil, M. A.; Sanchez-Reillo, R.; Fernandez-Pineda, C.

    2007-01-01

    Membrane distillation (MD) [1] is a relatively new process that is being investigated world-wide as a low cost, energy saving alternative to conventional separation processes such as distillation and reverse osmosis (RO). This process offers some advantages compared to other more popular separation processes, such as working at room conditions (pressure and temperature); low-grade, waste and/or alternative energy sources such as solar and geothermal energy may be used; a very high level of rejection with inorganic solutions; small equipment can be employed, etc. The driving force in MD processes is the vapor pressure difference across the membrane. A temperature difference is imposed across the membrane, which results in a vapor pressure difference. The principal problem in this kind of system is the accurate measurement of the recipient volume change, especially at very low flows. A cathetometer, with up to 0,05 mm resolution, is the instrument used to take these measurements, but the necessary human intervention makes this instrument not suitable for automated systems. In order to overcome this lack, a high resolution system is proposed, that makes automatic measurements of the volume of both recipients, cold and hot, at a rate of up to 10 times per second.

  6. Validity and repeatability of a depth camera-based surface imaging system for thigh volume measurement.

    Science.gov (United States)

    Bullas, Alice M; Choppin, Simon; Heller, Ben; Wheat, Jon

    2016-10-01

    Complex anthropometrics such as area and volume, can identify changes in body size and shape that are not detectable with traditional anthropometrics of lengths, breadths, skinfolds and girths. However, taking these complex with manual techniques (tape measurement and water displacement) is often unsuitable. Three-dimensional (3D) surface imaging systems are quick and accurate alternatives to manual techniques but their use is restricted by cost, complexity and limited access. We have developed a novel low-cost, accessible and portable 3D surface imaging system based on consumer depth cameras. The aim of this study was to determine the validity and repeatability of the system in the measurement of thigh volume. The thigh volumes of 36 participants were measured with the depth camera system and a high precision commercially available 3D surface imaging system (3dMD). The depth camera system used within this study is highly repeatable (technical error of measurement (TEM) of <1.0% intra-calibration and ~2.0% inter-calibration) but systematically overestimates (~6%) thigh volume when compared to the 3dMD system. This suggests poor agreement yet a close relationship, which once corrected can yield a usable thigh volume measurement.

  7. Reliability and validity of the lung volume measurement made by the BOD POD body composition system.

    Science.gov (United States)

    Davis, James A; Dorado, Silvia; Keays, Kathleen A; Reigel, Kimberly A; Valencia, Kristoffer S; Pham, Patrick H

    2007-01-01

    The BOD POD Body Composition System uses air-displacement plethysmography to measure body volume. To correct the body volume measurement for the subject's lung volume, the BOD POD utilizes pulmonary plethysmography to measure functional residual capacity (FRC) at mid-exhalation as that is the subject's lung volume during the body volume measurement. Normally, FRC is measured at end-exhalation. The BOD POD FRC measurement can be corrected to an end-exhalation volume by subtracting approximately one-half of the measured tidal volume. Our purpose was to determine the reliability and validity of the BOD POD FRC measurement at end-exhalation. Ninety-two healthy adults (half female) underwent duplicate FRC measurements by the BOD POD and one FRC measurement by a traditional gas dilution technique. The latter method was used as the reference method for the validity component of the study. The order of the FRC measurements by the two methods was randomized. The test-retest correlation coefficients for the duplicate BOD POD FRC measurements for the male and female subjects were 0.966 and 0.948, respectively. The mean differences between the BOD POD FRC trial #1 measurement and gas dilution FRC measurement for the male and female subjects were -32 and -23 ml, respectively. Neither difference was statistically significant. The correlation coefficients for these two measurements in the male and female subjects were 0.925 and 0.917, respectively. Based on these results, we conclude that the BOD POD FRC measurement in healthy males and females is both reliable and valid.

  8. A universal and flexible theodolite-camera system for making accurate measurements over large volumes

    Science.gov (United States)

    Zhang, Xiaohu; Zhu, Zhaokun; Yuan, Yun; Li, Lichun; Sun, Xiangyi; Yu, Qifeng; Ou, Jianliang

    2012-11-01

    Typically, optical measurement systems can achieve high accuracy over a limited volume, or cover a large volume with low accuracy. In this paper, we propose a universal way of integrating a camera with a theodolite to construct a theodolite-camera (TC) measurement system that can make measurements over a large volume with high accuracy. The TC inherits the advantages of high flexibility and precision from theodolite and camera, but it avoids the need to perform elaborate adjustments on the camera and theodolite. The TC provides a universal and flexible approach to the camera-on-theodolite system. We describe three types of TC based separately on: (i) a total station; (ii) a theodolite; and (iii) a general rotation frame. We also propose three corresponding calibration methods for the different TCs. Experiments have been conducted to verify the measuring accuracy of each of the three types of TC.

  9. Color structured light system of chest wall motion measurement for respiratory volume evaluation.

    Science.gov (United States)

    Chen, Huijun; Cheng, Yuan; Liu, Dongdong; Zhang, Xiaodong; Zhang, Jue; Que, Chengli; Wang, Guangfa; Fang, Jing

    2010-01-01

    We present a structured light system to dynamically measure human chest wall motion for respiratory volume estimation. Based on a projection of an encoded color pattern and a few active markers attached to the trunk, respiratory volumes are obtained by evaluating the 3-D topographic changes of the chest wall in an anatomically consistent measuring region during respiration. Three measuring setups are established: a single-sided illuminating-recording setup for standing posture, an inclined single-sided setup for supine posture, and a double-sided setup for standing posture. Results are compared with the pneumotachography and show good agreement in volume estimations [correlation coefficient: R>0.99 (Pevaluation with high accuracy, but also regional pulmonary function assessment in different chest wall behaviors, with the advantage of whole-field measurement.

  10. Reliable measurements for an image-derived sample volume in an open-configuration MR system

    Science.gov (United States)

    Han, Bong Soo; Lee, Man Woo; Hong, Cheolpyo

    2016-11-01

    Open-configuration magnetic resonance (MR) systems are becoming desirable for volume measurements of off-center samples due to their non-claustrophobic system configuration, excellent soft-tissue contrast, high efficiency, and low-cost. However, geometric distortion is produced by the unwanted background magnetic field and hinders volume measurements. The present study describes the characteristics of geometric distortion in off-center samples such as the thigh muscle and adipose tissue measurements using an open-type MR system. The American Association of Physicists in Medicine uniformity and linearity phantom was used for the detection and the evaluation of the geometric distortion. The geometric distortion decreased near the isocenter and increased toward the off-center. A cylindrical phantom image was acquired at the isocenter and was used as the distortion-free, reference image. Two cylindrical phantoms were scanned off-center at a position analogous to that of the human thigh. The differences between the two cylindrical phantom volumes and the reference volume were 1.62 % ± 0.16 and 5.18 % ± 0.14. Off-center-related MR imaging requires careful consideration for image interpretation and volumetric assessment of tissue.

  11. Improvement of fringe quality at LDA measuring volume using compact two hololens imaging system

    Science.gov (United States)

    Ghosh, Abhijit; Nirala, A. K.

    2015-03-01

    Design, analysis and construction of an LDA optical setup using conventional as well as compact two hololens imaging system have been performed. Fringes formed at measurement volume by both the imaging systems have been recorded. After experimentally analyzing these fringes, it is found that fringes obtained using compact two hololens imaging system get improved both qualitatively and quantitatively compared to that obtained using conventional imaging system. Hence it is concluded that use of the compact two hololens imaging system for making LDA optical setup is a better choice over the conventional one.

  12. The Development of a Flexible Measuring System for Muscle Volume Using Ultrasonography

    Science.gov (United States)

    Fukumoto, Kiyotaka; Fukuda, Osamu; Tsubai, Masayoshi; Muraki, Satoshi

    Quantification of muscle volume can be used as a means for the estimation of muscle strength. Its measuring process does not need the subject's muscular contractions so it is completely safe and particularly suited for elderly people. Therefore, we have developed a flexible measuring system for muscle volume using ultrasonography. In this system, an ultrasound probe is installed on a link mechanism which continuously scans fragmental images along the human body surface. These images are then measured and composed into a wide area cross-sectional image based on the spatial compounding method. The flexibility of the link mechanism enables the operator to measure the images under any body postures and body site. The spatial compounding method significantly reduces speckle and artifact noises from the composed cross-sectional image so that the operator can observe the individual muscles, such as Rectus femoris, Vastus intermedius, and so on, in detail. We conducted the experiments in order to examine the advantages of this system we have developed. The experimental results showed a high accuracy of the measuring position which was calculated using the link mechanism and presented the noise reduction effect based on the spatial compounding method. Finally, we confirmed high correlations between the MRI images and the ones of the developed system to verify the validity of the system.

  13. Fetal lung volume measurement by MRI with high-speed imaging systems

    Energy Technology Data Exchange (ETDEWEB)

    Osada, Hisao; Kaku, Kenshi [Chiba Univ. (Japan). Hospital

    2002-08-01

    Although ultrasonography is widely used for fetal morphologic observation, magnetic resonance imaging (MRI) has gained popularity as a new prenatal diagnostic method with recent introduction of high-speed imaging systems. Infants with lung hypoplasia affecting respiratory function require intensive management starting immediately after birth. Therefore, accurate prenatal differential diagnosis and severity evaluation are extremely important for these fetuses. The aim of this study is to measure fetal lung volume using a computer-based, three-dimensional MRI imaging system and to evaluate the possibility of clinical applications of this procedure. A total of 96 fetuses were evaluated, all were morphologically abnormal, and MRI was done for advanced assessment from 24 to 39 weeks gestation. Three-directional views of fetal chest were imaged by Signa Horizon, 1.5 Tesla, version 5.6 (General Electronics) with the following conditions; coil: TORSO coil, sequence: SSFSE (single shot fast spin echo), slice thickness: 5 mm, and imaging speed: 2 seconds/slice. To calculate the lung volume and create three-dimensional image, the lung area in each slice was traced out, then multiplied using computer image processing. Simultaneously, the volumes of all slices were summed to give the volume of each lung. Linear regression analysis and analysis of covariance (ANCOVA) were used for statistical analyses. In all cases, clear images were obtained, and were adequate for three-dimensional evaluation of the fetal lung. Thirty-five fetuses had poor outcomes, such as intrauterine fetal death, neonatal death, and intensive respiratory care. Regression lines of lung volume versus gestational week were calculated for these fetuses with poor outcome and 61 other fetuses with good outcome. ANCOVA, with gestational week as a covariant, revealed a significant intergroup difference in the lung volume (p<0.001). Similarly, regression lines of lung volume versus fetal body weight estimated by

  14. Volumetric measurement of tank volume

    Science.gov (United States)

    Walter, Richard T. (Inventor); Vanbuskirk, Paul D. (Inventor); Weber, William F. (Inventor); Froebel, Richard C. (Inventor)

    1991-01-01

    A method is disclosed for determining the volume of compressible gas in a system including incompressible substances in a zero-gravity environment consisting of measuring the change in pressure (delta P) for a known volume change rate (delta V/delta t) in the polytrophic region between isothermal and adiabatic conditions. The measurements are utilized in an idealized formula for determining the change in isothermal pressure (delta P sub iso) for the gas. From the isothermal pressure change (delta iso) the gas volume is obtained. The method is also applicable to determination of gas volume by utilizing work (W) in the compression process. In a passive system, the relationship of specific densities can be obtained.

  15. Can cerebral blood volume be measured reproducibly with an improved near infrared spectroscopy system?

    NARCIS (Netherlands)

    Ven, M.T.P. van de; Colier, W.N.J.M.; Sluijs, M.C. van der; Walraven, D.; Oeseburg, B.; Folgering, H.T.M.

    2001-01-01

    In some circumstances, cerebral blood volume (CBV) can be used as a measure for cerebral blood flow. A new near infrared spectroscope was used for determining the reproducibility of CBV measurements assessed by the O2-method. Twenty-seven healthy subjects were investigated. An intrasubject coefficie

  16. Software Quality Measurement for Distributed Systems. Volume 3. Distributed Computing Systems: Impact on Software Quality.

    Science.gov (United States)

    1983-07-01

    methodology precludes two computers from being casually linked together (as with SEAC and DYSEAC), but also lessens the likelihood of major innovations ...provide a more natural computer achitecture for applications such as artificial intelligence, real time command and control, and data base management. 3-7...state-of-the- art in how we can separate C31 nodes. A truly distributed C31 system may not be achievable for another 5 to 10 years. However, unless we

  17. Effect of the volume of the drainage system on the measurement of undrained thermo-poro-elastic parameters

    CERN Document Server

    Ghabezloo, Siavash; 10.1016/j.ijrmms.2009.03.001

    2009-01-01

    For evaluation of the undrained thermo-poro-elastic properties of saturated porous materials in conventional triaxial cells, it is important to take into account the effect of the dead volume of the drainage system. The compressibility and the thermal expansion of the drainage system along with the dead volume of the fluid filling this system, influence the measured pore pressure and volumetric strain during an undrained thermal or mechanical loading in a triaxial cell. The correction methods previously presented by Wissa (1969), Bishop (1976) and Ghabezloo and Sulem (2009) only permit to correct the measured pore pressures during an undrained isotropic compression test or an undrained heating test. An extension of these methods is presented in this paper to correct also the measured volumetric strain and consequently the measured undrained bulk compressibility and undrained thermal expansion coefficients during these tests. Two examples of application of the proposed correction method are presented on the re...

  18. A self-calibrating telemetry system for measurement of ventricular pressure-volume relations in conscious, freely moving rats.

    Science.gov (United States)

    Uemura, Kazunori; Kawada, Toru; Sugimachi, Masaru; Zheng, Can; Kashihara, Koji; Sato, Takayuki; Sunagawa, Kenji

    2004-12-01

    Using Bluetooth wireless technology, we developed an implantable telemetry system for measurement of the left ventricular pressure-volume relation in conscious, freely moving rats. The telemetry system consisted of a pressure-conductance catheter (1.8-Fr) connected to a small (14-g) fully implantable signal transmitter. To make the system fully telemetric, calibrations such as blood resistivity and parallel conductance were also conducted telemetrically. To estimate blood resistivity, we used four electrodes arranged 0.2 mm apart on the pressure-conductance catheter. To estimate parallel conductance, we used a dual-frequency method. We examined the accuracy of calibrations, stroke volume (SV) measurements, and the reproducibility of the telemetry. The blood resistivity estimated telemetrically agreed with that measured using an ex vivo cuvette method (y=1.09x - 11.9, r2= 0.88, n=10). Parallel conductance estimated by the dual-frequency (2 and 20 kHz) method correlated well with that measured by a conventional saline injection method (y=1.59x - 1.77, r2= 0.87, n=13). The telemetric SV closely correlated with the flowmetric SV during inferior vena cava occlusions (y=0.96x + 7.5, r2=0.96, n=4). In six conscious rats, differences between the repeated telemetries on different days (3 days apart on average) were reasonably small: 13% for end-diastolic volume, 20% for end-systolic volume, 28% for end-diastolic pressure, and 6% for end-systolic pressure. We conclude that the developed telemetry system enables us to estimate the pressure-volume relation with reasonable accuracy and reproducibility in conscious, untethered rats.

  19. Evaluation of solar radiation measurement systems: EPRI/NREL final test report. Volume 1

    Energy Technology Data Exchange (ETDEWEB)

    Stoffel, T; Riordan, C; Bigger, J

    1992-11-01

    Measured solar radiation resource data are needed by electric utilities to evaluate the potential of renewable energy options like photovoltaics in their service territory. In this final test report, we document a cooperative project of the Electric Power Research Institute (EPRI) and the National Renewable Energy Laboratory (NREL) to compare available measurement system options for performing solar radiation resource assessments. We present the detailed results of a 6-month field comparison of thermopile-based pyranometer and pyrheliometer solar irradiance measurement systems with two different implementations of the rotating shadowband radiometer (RSR) concept installed at NREL`s Solar Radiation Research Laboratory (SRRL) in Golden, Colorado.

  20. A Feasibility Study of Pressure Retarded Osmosis Power Generation System based on Measuring Permeation Volume using Reverse Osmosis Membrane

    Science.gov (United States)

    Enomoto, Hiroshi; Fujitsuka, Masashi; Hasegawa, Tomoyasu; Kuwada, Masatoshi; Tanioka, Akihiko; Minagawa, Mie

    Pressure Retarded Osmosis (PRO) power generation system is a hydroelectric power system which utilize permeation flow through a semi-permeable membrane. Permeation flow is generated by potential energy of salinity difference between sea water and fresh water. As membrane cost is expensive, permeation performance of membrane must be higher to realize PRO system. We have investigated Reverse Osmosis (RO) membrane products as semi-permeable membrane and measured permeation volume of a few products. Generation power by membrane area calculated from permeation volume is about 0.62W/m2. But by our improvements (more salt water volume, spacer of fresh water channel with a function of discharging concentrated salinity, extra low pressure type of membrane, washing support layer of membrane when generation power reduces to half), generation power may be 2.43W/m2. Then power system cost is about 4.1 million yen/kW. In addition, if support layer of membrane makes thinner and PRO system is applied to the equipment that pumping power on another purpose is avairable (wastewater treatment plant located at the seaside, thermal and nuclear power plant or sea water desalination plant), generation power may be more. By these improvements PRO system may be able to realize at the cost close to photovoltaic power system.

  1. Cosmological Measures without Volume Weighting

    CERN Document Server

    Page, Don N

    2008-01-01

    Many cosmologists (myself included) have advocated volume weighting for the cosmological measure problem, weighting spatial hypersurfaces by their volume. However, this often leads to the Boltzmann brain problem, that almost all observations would be by momentary Boltzmann brains that arise very briefly as quantum fluctuations in the late universe when it has expanded to a huge size, so that our observations (too ordered for Boltzmann brains) would be highly atypical and unlikely. Here it is suggested that volume weighting may be a mistake. Volume averaging is advocated as an alternative. One consequence would be a loss of the argument for eternal inflation.

  2. Optimal use of buffer volumes for the measurement of atmospheric gas concentration in multi-point systems

    Science.gov (United States)

    Cescatti, Alessandro; Marcolla, Barbara; Goded, Ignacio; Gruening, Carsten

    2016-09-01

    Accurate multi-point monitoring systems are required to derive atmospheric measurements of greenhouse gas concentrations both for the calculation of surface fluxes with inversion transport models and for the estimation of non-turbulent components of the mass balance equation (i.e. advection and storage fluxes) at eddy covariance sites. When a single analyser is used to monitor multiple sampling points, the deployment of buffer volumes (BVs) along sampling lines can reduce the uncertainty due to the discrete temporal sampling of the signal. In order to optimize the use of buffer volumes we explored various set-ups by simulating their effect on time series of high-frequency CO2 concentration collected at three Fluxnet sites. Besides, we proposed a novel scheme to calculate half-hourly weighted arithmetic means from discrete point samples, accounting for the probabilistic fraction of the signal generated in the averaging period. Results show that the use of BVs with the new averaging scheme reduces the mean absolute error (MAE) up to 80 % compared to a set-up without BVs and up to 60 % compared to the case with BVs and a standard, non-weighted averaging scheme. The MAE of CO2 concentration measurements was observed to depend on the variability of the concentration field and on the size of BVs, which therefore have to be carefully dimensioned. The optimal volume size depends on two main features of the instrumental set-up: the number of measurement points and the time needed to sample at one point (i.e. line purging plus sampling time). A linear and consistent relationship was observed at all sites between the sampling frequency, which summarizes the two features mentioned above, and the renewal frequency associated with the volume. Ultimately, this empirical relationship can be applied to estimate the optimal volume size according to the technical specifications of the sampling system.

  3. Ultrasonographic Measures of Volume Responsiveness

    Science.gov (United States)

    2017-02-01

    AFRL-SA-WP-SR-2017-0005 Ultrasonographic Measures of Volume Responsiveness Sarah B. Murthi, MD February 2017...use, or sell any patented invention that may relate to them. Qualified requestors may obtain copies of this report from the Defense Technical...TITLE AND SUBTITLE Ultrasonographic Measures of Volume Responsiveness 5a. CONTRACT NUMBER FA8650-13-2-6D10 5b. GRANT NUMBER 5c. PROGRAM

  4. VOLUMNECT: measuring volumes with Kinect

    Science.gov (United States)

    Quintino Ferreira, Beatriz; Griné, Miguel; Gameiro, Duarte; Costeira, João. Paulo; Sousa Santos, Beatriz

    2014-03-01

    This article presents a solution to volume measurement object packing using 3D cameras (such as the Microsoft KinectTM). We target application scenarios, such as warehouses or distribution and logistics companies, where it is important to promptly compute package volumes, yet high accuracy is not pivotal. Our application auto- matically detects cuboid objects using the depth camera data and computes their volume and sorting it allowing space optimization. The proposed methodology applies to a point cloud simple computer vision and image processing methods, as connected components, morphological operations and Harris corner detector, producing encouraging results, namely an accuracy in volume measurement of 8mm. Aspects that can be further improved are identified; nevertheless, the current solution is already promising turning out to be cost effective for the envisaged scenarios.

  5. Cortical thickness, surface area and volume measures in Parkinson's disease, multiple system atrophy and progressive supranuclear palsy.

    Directory of Open Access Journals (Sweden)

    Amanda Worker

    Full Text Available Parkinson's disease (PD, Multiple System Atrophy (MSA and Progressive Supranuclear Palsy (PSP are neurodegenerative diseases that can be difficult to distinguish clinically. The objective of the current study was to use surface-based analysis techniques to assess cortical thickness, surface area and grey matter volume to identify unique morphological patterns of cortical atrophy in PD, MSA and PSP and to relate these patterns of change to disease duration and clinical features.High resolution 3D T1-weighted MRI volumes were acquired from 14 PD patients, 18 MSA, 14 PSP and 19 healthy control participants. Cortical thickness, surface area and volume analyses were carried out using the automated surface-based analysis package FreeSurfer (version 5.1.0. Measures of disease severity and duration were assessed for correlation with cortical morphometric changes in each clinical group.Results show that in PSP, widespread cortical thinning and volume loss occurs within the frontal lobe, particularly the superior frontal gyrus. In addition, PSP patients also displayed increased surface area in the pericalcarine. In comparison, PD and MSA did not display significant changes in cortical morphology.These results demonstrate that patients with clinically established PSP exhibit distinct patterns of cortical atrophy, particularly affecting the frontal lobe. These results could be used in the future to develop a useful clinical application of MRI to distinguish PSP patients from PD and MSA patients.

  6. Excess molar volume of the acetonitrile + alcohol systems at 298.15 K. Part I: Density measurements for acetonitrile + methanol, + ethanol systems

    Directory of Open Access Journals (Sweden)

    SLOBODAN P. SERBANOVIC

    2002-09-01

    Full Text Available The excess molar volume VE of the binary liquid systems acetonitrile + methanol and acetonitrile + ethanol has been evaluated from density measurements at 298.15 K and at atmospheric pressure over the entire composition range. A vibrating tube densimeter, type Anton Paar DMA 55, was applied for these measurements. The Redlich–Kister equation was used to fit the experimental VE data.

  7. Predicted versus measured thoracic gas volumes of collegiate athletes made by the BOD POD air displacement plethysmography system.

    Science.gov (United States)

    Wagner, Dale R

    2015-10-01

    Measured (TGVm) and predicted (TGVp) thoracic gas volumes from the BOD POD were compared in 33 lean, university athletes. On average, TGVp (3.529 L) was not significantly different (p = 0.343) from TGVm (3.628 L); however, there was a bias (r = -0.703, p < 0.001). The difference in the percentage of body fat (BF) was within ±2% BF for 76% of the sample, but athletes at the extremes of height should have TGV measured.

  8. Test-retest reliability of automated whole body and compartmental muscle volume measurements on a wide bore 3T MR system

    Energy Technology Data Exchange (ETDEWEB)

    Thomas, Marianna S.; Newman, David; Kasmai, Bahman; Greenwood, Richard; Malcolm, Paul N. [Norfolk and Norwich University Hospital, Department of Radiology, Norwich (United Kingdom); Leinhard, Olof Dahlqvist [Linkoeping University, Center for Medical Image Science and Visualization, Linkoeping (Sweden); Linkoeping University, Department of Medical and Health Sciences, Linkoeping (Sweden); Karlsson, Anette; Borga, Magnus [Linkoeping University, Center for Medical Image Science and Visualization, Linkoeping (Sweden); Linkoeping University, Department of Biomedical Engineering, Linkoeping (Sweden); Rosander, Johannes [Advanced MR Analytics AB, Linkoeping (Sweden); Toms, Andoni P. [Norfolk and Norwich University Hospital, Department of Radiology, Norwich (United Kingdom); Radiology Academy, Cotman Centre, Norwich, Norfolk (United Kingdom)

    2014-09-15

    To measure the test-retest reproducibility of an automated system for quantifying whole body and compartmental muscle volumes using wide bore 3 T MRI. Thirty volunteers stratified by body mass index underwent whole body 3 T MRI, two-point Dixon sequences, on two separate occasions. Water-fat separation was performed, with automated segmentation of whole body, torso, upper and lower leg volumes, and manually segmented lower leg muscle volumes. Mean automated total body muscle volume was 19.32 L (SD9.1) and 19.28 L (SD9.12) for first and second acquisitions (Intraclass correlation coefficient (ICC) = 1.0, 95 % level of agreement -0.32-0.2 L). ICC for all automated test-retest muscle volumes were almost perfect (0.99-1.0) with 95 % levels of agreement 1.8-6.6 % of mean volume. Automated muscle volume measurements correlate closely with manual quantification (right lower leg: manual 1.68 L (2SD0.6) compared to automated 1.64 L (2SD 0.6), left lower leg: manual 1.69 L (2SD 0.64) compared to automated 1.63 L (SD0.61), correlation coefficients for automated and manual segmentation were 0.94-0.96). Fully automated whole body and compartmental muscle volume quantification can be achieved rapidly on a 3 T wide bore system with very low margins of error, excellent test-retest reliability and excellent correlation to manual segmentation in the lower leg. (orig.)

  9. Camera on Vessel: A Camera-Based System to Measure Change in Water Volume in a Drinking Glass

    Directory of Open Access Journals (Sweden)

    Idowu Ayoola

    2015-09-01

    Full Text Available A major problem related to chronic health is patients’ “compliance” with new lifestyle changes, medical prescriptions, recommendations, or restrictions. Heart-failure and hemodialysis patients are usually placed on fluid restrictions due to their hemodynamic status. A holistic approach to managing fluid imbalance will incorporate the monitoring of salt-water intake, body-fluid retention, and fluid excretion in order to provide effective intervention at an early stage. Such an approach creates a need to develop a smart device that can monitor the drinking activities of the patient. This paper employs an empirical approach to infer the real water level in a conically shapped glass and the volume difference due to changes in water level. The method uses a low-resolution miniaturized camera to obtain images using an Arduino microcontroller. The images are processed in MATLAB. Conventional segmentation techniques (such as a Sobel filter to obtain a binary image are applied to extract the level gradient, and an ellipsoidal fitting helps to estimate the size of the cup. The fitting (using least-squares criterion between derived measurements in pixel and the real measurements shows a low covariance between the estimated measurement and the mean. The correlation between the estimated results to ground truth produced a variation of 3% from the mean.

  10. Measured and Calculated Volumes of Wetland Depressions

    Data.gov (United States)

    U.S. Environmental Protection Agency — Measured and calculated volumes of wetland depressions This dataset is associated with the following publication: Wu, Q., and C. Lane. Delineation and quantification...

  11. Measurable inhomogeneities in stock trading volume flow

    Science.gov (United States)

    Cortines, A. A. G.; Riera, R.; Anteneodo, C.

    2008-08-01

    We investigate the statistics of volumes of shares traded in stock markets. We show that the stochastic process of trading volumes can be understood on the basis of a mixed Poisson process at the microscopic time level. The beta distribution of the second kind (also known as q-gamma distribution), that has been proposed to describe empirical volume histograms, naturally results from our analysis. In particular, the shape of the distribution at small volumes is governed by the degree of granularity in the trading process, while the exponent controlling the tail is a measure of the inhomogeneities in market activity. Furthermore, the present case furnishes empirical evidence of how power law probability distributions can arise as a consequence of a fluctuating intrinsic parameter.

  12. Volume Measurement in Solid Objects Using Artificial Vision Technique

    Science.gov (United States)

    Cordova-Fraga, T.; Martinez-Espinosa, J. C.; Bernal, J.; Huerta-Franco, R.; Sosa-Aquino, M.; Vargas-Luna, M.

    2004-09-01

    A simple system using artificial vision technique for measuring the volume of solid objects is described. The system is based on the acquisition of an image sequence of the object while it is rotating on an automated mechanism controlled by a PC. Volumes of different objects such as a sphere, a cylinder and also a carrot were measured. The proposed algorithm was developed in environment LabView 6.1. This technique can be very useful when it is applied to measure the human body for evaluating its body composition.

  13. Facilitating cartilage volume measurement using MRI

    Energy Technology Data Exchange (ETDEWEB)

    Maataoui, Adel, E-mail: adel.maataoui@gmx.d [Institute for Diagnostic and Interventional Radiology, Johann Wolfgang Goethe University, Theodor-Stern-Kai 7, 60590 Frankfurt am Main (Germany); Gurung, Jessen, E-mail: jessen.gurung@gmx.d [Institute for Diagnostic and Interventional Radiology, Johann Wolfgang Goethe University, Theodor-Stern-Kai 7, 60590 Frankfurt am Main (Germany); Ackermann, Hanns, E-mail: h.ackermann@add.uni-frankfurt.d [Institute for Epidemiology and Medical Statistics, Johann Wolfgang Goethe University, Theodor-Stern-Kai 7, 60590 Frankfurt am Main (Germany); Abolmaali, Nasreddin [Biological and Molecular Imaging, ZIK OncoRay - Radiation Research in Oncology, Medical Faculty Carl Gustav Carus, TU Dresden, Fetscherstrasse 74, 01307 Dresden (Germany); Kafchitsas, Konstantinos [Department of Orthopedics and Orthopedic Surgery, Johannes Gutenberg University, Langenbeckstrasse 1, 55131 Mainz (Germany); Vogl, Thomas J., E-mail: t.vogl@em.uni-frankfurt.d [Institute for Diagnostic and Interventional Radiology, Johann Wolfgang Goethe University, Theodor-Stern-Kai 7, 60590 Frankfurt am Main (Germany); Khan, M. Fawad, E-mail: fawad@gmx.d [Institute for Diagnostic and Interventional Radiology, Johann Wolfgang Goethe University, Theodor-Stern-Kai 7, 60590 Frankfurt am Main (Germany)

    2010-08-15

    Purpose: To compare quantitative cartilage volume measurement (CVM) using different slice thicknesses. Materials and methods: Ten knees were scanned with a 1.5 T MRI (Sonata, Siemens, Erlangen, Germany) using a 3D gradient echo sequence (FLASH, fast low-angle shot). Cartilage volume of the medial and lateral tibial plateau was measured by two independent readers in 1.5 mm, 3.0 mm and 5.0 mm slices using the Argus software application. Accuracy and time effectiveness served as control parameters. Results: Determining cartilage volume, time for calculation diminished for the lateral tibial plateau from 384.6 {+-} 127.7 s and 379.1 {+-} 117.6 s to 214.9 {+-} 109.9 s and 213.9 {+-} 102.2 s to 122.1 {+-} 60.1 s and 126.8 {+-} 56.2 s and for the medial tibial plateau from 465.0 {+-} 147.7 s and 461.8 {+-} 142.7 s to 214.0 {+-} 67.9 s and 208.9 {+-} 66.2 s to 132.6 {+-} 41.5 s and 130.6 {+-} 42.0 s measuring 1.5 mm, 3 mm and 5 mm slices, respectively. No statistically significant difference between cartilage volume measurements was observed (p > 0.05) while very good inter-reader correlation was evaluated. Conclusion: CVM using 1.5 mm slices provides no higher accuracy than cartilage volume measurement in 5 mm slices while an overall time saving up to 70% is possible.

  14. Micro analysis of fringe field formed inside LDA measuring volume

    Science.gov (United States)

    Ghosh, Abhijit; Nirala, A. K.

    2016-05-01

    In the present study we propose a technique for micro analysis of fringe field formed inside laser Doppler anemometry (LDA) measuring volume. Detailed knowledge of the fringe field obtained by this technique allows beam quality, alignment and fringe uniformity to be evaluated with greater precision and may be helpful for selection of an appropriate optical element for LDA system operation. A complete characterization of fringes formed at the measurement volume using conventional, as well as holographic optical elements, is presented. Results indicate the qualitative, as well as quantitative, improvement of fringes formed at the measurement volume by holographic optical elements. Hence, use of holographic optical elements in LDA systems may be advantageous for improving accuracy in the measurement.

  15. Novel system using microliter order sample volume for measuring arterial radioactivity concentrations in whole blood and plasma for mouse PET dynamic study.

    Science.gov (United States)

    Kimura, Yuichi; Seki, Chie; Hashizume, Nobuya; Yamada, Takashi; Wakizaka, Hidekatsu; Nishimoto, Takahiro; Hatano, Kentaro; Kitamura, Keishi; Toyama, Hiroshi; Kanno, Iwao

    2013-11-21

    This study aimed to develop a new system, named CD-Well, for mouse PET dynamic study. CD-Well allows the determination of time-activity curves (TACs) for arterial whole blood and plasma using 2-3 µL of blood per sample; the minute sample size is ideal for studies in small animals. The system has the following merits: (1) measures volume and radioactivity of whole blood and plasma separately; (2) allows measurements at 10 s intervals to capture initial rapid changes in the TAC; and (3) is compact and easy to handle, minimizes blood loss from sampling, and delay and dispersion of the TAC. CD-Well has 36 U-shaped channels. A drop of blood is sampled into the opening of the channel and stored there. After serial sampling is completed, CD-Well is centrifuged and scanned using a flatbed scanner to define the regions of plasma and blood cells. The length measured is converted to volume because the channels have a precise and uniform cross section. Then, CD-Well is exposed to an imaging plate to measure radioactivity. Finally, radioactivity concentrations are computed. We evaluated the performance of CD-Well in in vitro measurement and in vivo (18)F-fluorodeoxyglucose and [(11)C]2-carbomethoxy-3β-(4-fluorophenyl) tropane studies. In in vitro evaluation, per cent differences (mean±SE) from manual measurement were 4.4±3.6% for whole blood and 4.0±3.5% for plasma across the typical range of radioactivity measured in mouse dynamic study. In in vivo studies, reasonable TACs were obtained. The peaks were captured well, and the time courses coincided well with the TAC derived from PET imaging of the heart chamber. The total blood loss was less than 200 µL, which had no physiological effect on the mice. CD-Well demonstrates satisfactory performance, and is useful for mouse PET dynamic study.

  16. On-line Measuring Method for Shell Chamber Volume

    Institute of Scientific and Technical Information of China (English)

    ZHANG Li-zhong; WANG De-min; JIANG Tao; CAO Guo-hua; WANG Qi

    2005-01-01

    Using the ideal gas state equation, an on-line measuring method for the shell chamber volume is studied in this paper. After analyzing how various measurement parameters affect the measurement accuracy, the system parameters are optimized in this method. Because the shape and volume of the tested items are similar, the method of using "tamping" to raise the accuracy and speed of the measurement is put forward. Based on the work above, a prototype of the testing instrument for shell chamber volume was developed, automatically testing and controlling. Compared with the method of "water weight", this method is more accurate, quicker and more automotive, so it is adaptable for the use of on-line detection.

  17. Calorimetric measuring systems

    DEFF Research Database (Denmark)

    Ritchie, Andrew Ewen; Pedersen, John Kim; Blaabjerg, Frede

    2004-01-01

    the system cooling requirement. A common problem is that high-frequency phenomena like proximity effect, skin effect, hysteresis losses, and eddy current losses appear in the systems. These losses are very difficult to treat both theoretically and in practice. It is often difficult to measure the effect......Power Electronics remains an emerging technology. New materials, new devices, and new circuit topologies reduce the cost, weight, and volume for important applications [1]. Two important factors in power electronic circuits are the switching speed of the devices and the total power losses...... in the system. If the switching speed can be increased, improvements may be possible (e.g., current ripple in an electrical machine or physical size of passive components may be reduced). On the other hand, increased switching speed may cause additional losses in a power electronic system and increase...

  18. Enterprise performance measurement systems

    Directory of Open Access Journals (Sweden)

    Milija Bogavac

    2014-10-01

    Full Text Available Performance measurement systems are an extremely important part of the control and management actions, because in this way a company can determine its business potential, its market power, potential and current level of business efficiency. The significance of measurement consists in influencing the relationship between the results of reproduction (total volume of production, value of production, total revenue and profit and investments to achieve these results (factors of production spending and hiring capital in order to achieve the highest possible quality of the economy. (The relationship between the results of reproduction and investment to achieve them quantitatively determines economic success as the quality of the economy. Measuring performance allows the identification of the economic resources the company has, so looking at the key factors that affect its performance can help to determine the appropriate course of action.

  19. Bioimpedance Measurement of Segmental Fluid Volumes and Hemodynamics

    Science.gov (United States)

    Montgomery, Leslie D.; Wu, Yi-Chang; Ku, Yu-Tsuan E.; Gerth, Wayne A.; DeVincenzi, D. (Technical Monitor)

    2000-01-01

    Bioimpedance has become a useful tool to measure changes in body fluid compartment volumes. An Electrical Impedance Spectroscopic (EIS) system is described that extends the capabilities of conventional fixed frequency impedance plethysmographic (IPG) methods to allow examination of the redistribution of fluids between the intracellular and extracellular compartments of body segments. The combination of EIS and IPG techniques was evaluated in the human calf, thigh, and torso segments of eight healthy men during 90 minutes of six degree head-down tilt (HDT). After 90 minutes HDT the calf and thigh segments significantly (P < 0.05) lost conductive volume (eight and four percent, respectively) while the torso significantly (P < 0.05) gained volume (approximately three percent). Hemodynamic responses calculated from pulsatile IPG data also showed a segmental pattern consistent with vascular fluid loss from the lower extremities and vascular engorgement in the torso. Lumped-parameter equivalent circuit analyses of EIS data for the calf and thigh indicated that the overall volume decreases in these segments arose from reduced extracellular volume that was not completely balanced by increased intracellular volume. The combined use of IPG and EIS techniques enables noninvasive tracking of multi-segment volumetric and hemodynamic responses to environmental and physiological stresses.

  20. The validity and reliability of computed tomography orbital volume measurements.

    Science.gov (United States)

    Diaconu, Silviu C; Dreizin, David; Uluer, Mehmet; Mossop, Corey; Grant, Michael P; Nam, Arthur J

    2017-09-01

    Orbital volume calculations allow surgeons to design patient-specific implants to correct volume deficits. It is estimated that changes as small as 1 ml in orbital volume can lead to enophthalmos. Awareness of the limitations of orbital volume computed tomography (CT) measurements is critical to differentiate between true volume differences and measurement error. The aim of this study is to analyze the validity and reliability of CT orbital volume measurements. A total of 12 cadaver orbits were scanned using a standard CT maxillofacial protocol. Each orbit was dissected to isolate the extraocular muscles, fatty tissue, and globe. The empty bony orbital cavity was then filled with sculpting clay. The volumes of the muscle, fat, globe, and clay (i.e., bony orbital cavity) were then individually measured via water displacement. The CT-derived volumes, measured by manual segmentation, were compared to the direct measurements to determine validity. The difference between CT orbital volume measurements and physically measured volumes is not negligible. Globe volumes have the highest agreement with 95% of differences between -0.5 and 0.5 ml, bony volumes are more likely to be overestimated with 95% of differences between -1.8 and 2.6 ml, whereas extraocular muscle volumes have poor validity and should be interpreted with caution. Copyright © 2017 European Association for Cranio-Maxillo-Facial Surgery. Published by Elsevier Ltd. All rights reserved.

  1. The Use of Helmholtz Resonance for Measuring the Volume of Liquids and Solids

    Directory of Open Access Journals (Sweden)

    Clive E. Davies

    2010-11-01

    Full Text Available An experimental investigation was undertaken to ascertain the potential of using Helmholtz resonance for volume determination and the factors that may influence accuracy. The uses for a rapid non-interference volume measurement system range from agricultural produce and mineral sampling through to liquid fill measurements. By weighing the sample the density can also measured indirectly.

  2. The use of Helmholtz resonance for measuring the volume of liquids and solids.

    Science.gov (United States)

    Webster, Emile S; Davies, Clive E

    2010-01-01

    An experimental investigation was undertaken to ascertain the potential of using Helmholtz resonance for volume determination and the factors that may influence accuracy. The uses for a rapid non-interference volume measurement system range from agricultural produce and mineral sampling through to liquid fill measurements. By weighing the sample the density can also measured indirectly.

  3. High Production Volume Information System (HPVIS)

    Data.gov (United States)

    U.S. Environmental Protection Agency — The High Production Volume Information System (HPVIS) provides access to select health and environmental effect information on chemicals that are manufactured in...

  4. Sex Assessment from the Volume of the First Metatarsal Bone: A Comparison of Linear and Volume Measurements.

    Science.gov (United States)

    Gibelli, Daniele; Poppa, Pasquale; Cummaudo, Marco; Mattia, Mirko; Cappella, Annalisa; Mazzarelli, Debora; Zago, Matteo; Sforza, Chiarella; Cattaneo, Cristina

    2017-02-23

    Sexual dimorphism is a crucial characteristic of skeleton. In the last years, volumetric and surface 3D acquisition systems have enabled anthropologists to assess surfaces and volumes, whose potential still needs to be verified. This article aimed at assessing volume and linear parameters of the first metatarsal bone through 3D acquisition by laser scanning. Sixty-eight skeletons underwent 3D scan through laser scanner: Seven linear measurements and volume from each bone were assessed. A cutoff value of 13,370 mm(3) was found, with an accuracy of 80.8%. Linear measurements outperformed volume: metatarsal length and mediolateral width of base showed higher cross-validated accuracies (respectively, 82.1% and 79.1%, raising at 83.6% when both of them were included). Further studies are needed to verify the real advantage for sex assessment provided by volume measurements. © 2017 American Academy of Forensic Sciences.

  5. Laser-induced incandescence: Towards quantitative soot volume fraction measurements

    Energy Technology Data Exchange (ETDEWEB)

    Tzannis, A.P.; Wienbeucker, F.; Beaud, P.; Frey, H.-M.; Gerber, T.; Mischler, B.; Radi, P.P. [Paul Scherrer Inst. (PSI), Villigen (Switzerland)

    1999-08-01

    Laser-Induced Incandescence has recently emerged as a versatile tool for measuring soot volume fraction in a wide range of combustion systems. In this work we investigate the essential features of the method. LII is based on the acquisition of the incandescence of soot when heated through a high power laser pulse. Initial experiments have been performed on a model laboratory flame. The behaviour of the LII signal is studied experimentally. By applying numerical calculations we investigate the possibility to obtain two-dimensional soot volume fraction distributions. For this purpose a combination of LII with other techniques is required. This part is discussed in some extent and the future work is outlined. (author) 4 figs., 3 refs.

  6. Gamma ray densitometry techniques for measuring of volume fractions

    Energy Technology Data Exchange (ETDEWEB)

    Affonso, Renato Raoni Werneck; Silva, Ademir Xavier da; Salgado, Cesar Marques, E-mail: raoniwa@yahoo.com.br, E-mail: ademir@nuclear.ufrj.br, E-mail: otero@ien.gov.br [Instituto de Engenharia Nuclear (IEN/CNEN-RJ), Rio de Janeiro, RJ (Brazil)

    2015-07-01

    Knowledge of the volume fraction in a multiphase flow is of key importance in predicting the performance of many systems and processes. It is therefore an important parameter to characterize such flows. In the context of nuclear techniques, the gamma ray densitometry is promising and this is due to its non-invasive characteristics and very reliable results. It is used in several applications for multiphase flows (water-oil-air), which are employed tools such as: computational fluid dynamics, artificial neural networks and statistical methods of radiation transport, such as the Monte Carlo method. Based on the gamma radiation techniques for measurements of volume fractions, the aim of this paper is to present several techniques developed for this purpose. (author)

  7. Measurement and analysis of grain boundary grooving by volume diffusion

    Science.gov (United States)

    Hardy, S. C.; Mcfadden, G. B.; Coriell, S. R.; Voorhees, P. W.; Sekerka, R. F.

    1991-01-01

    Experimental measurements of isothermal grain boundary grooving by volume diffusion are carried out for Sn bicrystals in the Sn-Pb system near the eutectic temperature. The dimensions of the groove increase with a temporal exponent of 1/3, and measurement of the associated rate constant allows the determination of the product of the liquid diffusion coefficient D and the capillarity length Gamma associated with the interfacial free energy of the crystal-melt interface. The small-slope theory of Mullins is generalized to the entire range of dihedral angles by using a boundary integral formulation of the associated free boundary problem, and excellent agreement with experimental groove shapes is obtained. By using the diffusivity measured by Jordon and Hunt, the present measured values of Gamma are found to agree to within 5 percent with the values obtained from experiments by Gunduz and Hunt on grain boundary grooving in a temperature gradient.

  8. Residual limb volume change: Systematic review of measurement and management

    Directory of Open Access Journals (Sweden)

    Joan E. Sanders, PhD

    2011-10-01

    Full Text Available Management of residual limb volume affects decisions regarding timing of fit of the first prosthesis, when a new prosthetic socket is needed, design of a prosthetic socket, and prescription of accommodation strategies for daily volume fluctuations. This systematic review assesses what is known about measurement and management of residual limb volume change in persons with lower-limb amputation. Publications that met inclusion criteria were grouped into three categories: group I: descriptions of residual limb volume measurement techniques; group II: studies investigating the effect of residual limb volume change on clinical care in people with lower-limb amputation; and group III: studies of residual limb volume management techniques or descriptions of techniques for accommodating or controlling residual limb volume. We found that many techniques for the measurement of residual limb volume have been described but clinical use is limited largely because current techniques lack adequate resolution and in-socket measurement capability. Overall, limited evidence exists regarding the management of residual limb volume, and the evidence available focuses primarily on adults with transtibial amputation in the early postoperative phase. While we can draw some insights from the available research about residual limb volume measurement and management, further research is required.

  9. Prediction of forage intake using in vitro gas production methods: Comparison of multiphase fermentation kinetics measured in an automated gas test, and combined gas volume and substrate degradability measurements in a manual syringe system

    NARCIS (Netherlands)

    Blümmel, M.; Cone, J.W.; Gelder, van A.H.; Nshalai, I.; Umunna, N.N.; Makkar, H.P.S.; Becker, K.

    2005-01-01

    This study investigated two approaches to in vitro analysis of gas production data, being a three phase model with long (¿72 h) incubation times, to obtain kinetics and asymptotic values of gas production, and combination of gas volume measurements with residue determinations after a relatively shor

  10. Excess Molar Volume of Binary Systems Containing Mesitylene

    Directory of Open Access Journals (Sweden)

    Morávková, L.

    2013-05-01

    Full Text Available This paper presents a review of density measurements for binary systems containing 1,3,5-trimethylbenzene (mesitylene with a variety of organic compounds at atmospheric pressure. Literature data of the binary systems were divided into nine basic groups by the type of contained organic compound with mesitylene. The excess molar volumes calculated from the experimental density values have been compared with literature data. Densities were measured by a few experimental methods, namely using a pycnometer, a dilatometer or a commercial apparatus. The overview of the experimental data and shape of the excess molar volume curve versus mole fraction is presented in this paper. The excess molar volumes were correlated by Redlich–Kister equation. The standard deviations for fitting of excess molar volume versus mole fraction are compared. Found literature data cover a huge temperature range from (288.15 to 343.15 K.

  11. Measurement and COrrelation on Viscosity and Apparent Molar Volume of Ternary System for L—ascorbic Acid in Aqueous D—Glucose and Sucrose Solutions

    Institute of Scientific and Technical Information of China (English)

    赵长伟; 马沛生

    2003-01-01

    Visosities and densities at ,several temperatures from 293.15 K to 313.15K are reported for L-ascorbic acid in aqueous glucose and sucrose solutions at different concentrations.The parameters of density,Viscosity coefficient B and partial molar volume are calculated by regression.The experimental results show that densities and viscositis decrease as temperature increases at the same solute and solvent (glucose and sucrose aueous solution)concentrations,and increase with concentration of glucose and sucrose at the same solute concentration and temperature,B increases with concentration of glucose and sucrose and temaperature,L-ascorbic acid is sturcture-breaker or structure-making for the glucose and sucrose aqueous solutions ,Furthermore,the solute-solvent interactions in ternary systems of water-glucose-electrolyte and water-sucrose-electrolyte are discussed.

  12. Clinical Relevance of Brain Volume Measures in Multiple Sclerosis

    DEFF Research Database (Denmark)

    De Stefano, Nicola; Airas, Laura; Grigoriadis, Nikolaos

    2014-01-01

    (e.g. SIENA [Structural Image Evaluation using Normalization of Atrophy]). Although these methods are sensitive and reproducible, caution must be exercised when interpreting brain volume data, as numerous factors (e.g. pseudoatrophy) may have a confounding effect on measurements, especially...... therefore have important clinical implications affecting treatment decisions, with several clinical trials now demonstrating an effect of disease-modifying treatments (DMTs) on reducing brain volume loss. In clinical practice, it may therefore be important to consider the potential impact of a therapy...... on reducing the rate of brain volume loss. This article reviews the measurement of brain volume in clinical trials and practice, the effect of DMTs on brain volume change across trials and the clinical relevance of brain volume loss in MS....

  13. Membrane diffusion- and capillary blood volume measurements are not useful as screening tools for pulmonary arterial hypertension in systemic sclerosis: a case control study

    Directory of Open Access Journals (Sweden)

    Spreeuwenberg Marieke D

    2008-10-01

    Full Text Available Abstract Background There is no optimal screening tool for the assessment of pulmonary arterial hypertension (PAH in patients with systemic sclerosis (SSc. A decreasing transfer factor of the lung for CO (TLCO is associated with the development of PAH in SSc. TLCO can be partitioned into the diffusion of the alveolar capillary membrane (Dm and the capillary blood volume (Vc. The use of the partitioned diffusion to detect PAH in SSc is not well established yet. This study evaluates whether Dm and Vc could be candidates for further study of the use for screening for PAH in SSc. Methods Eleven SSc patients with PAH (SScPAH+, 13 SSc patients without PAH (SScPAH- and 10 healthy control subjects were included. Pulmonary function testing took place at diagnosis of PAH. TLCO was partitioned according to Roughton and Forster. As pulmonary fibrosis in SSc influences values of the (partitioned TLCO, these were adjusted for fibrosis score as assessed on HRCT. Results TLCO as percentage of predicted (% was lower in SScPAH+ than in SScPAH- (41 ± 7% vs. 63 ± 12%, p vs. 39 ± 12%, p Conclusion SScPAH+ patients have lower Dm% than SScPAH- patients. There are no correlations between Dm% and hemodynamic parameters of PAH in SScPAH+. These findings do not support further study of the role of partitioning TLCO in the diagnostic work- up for PAH in SSc.

  14. The KamLAND Full-Volume Calibration System

    Energy Technology Data Exchange (ETDEWEB)

    KamLAND Collaboration; Berger, B. E.; Busenitz, J.; Classen, T.; Decowski, M. P.; Dwyer, D. A.; Elor, G.; Frank, A.; Freedman, S. J.; Fujikawa, B. K.; Galloway, M.; Gray, F.; Heeger, K. M.; Hsu, L.; Ichimura, K.; Kadel, R.; Keefer, G.; Lendvai, C.; McKee, D.; O' Donnell, T.; Piepke, A.; Steiner, H. M.; Syversrud, D.; Wallig, J.; Winslow, L. A.; Ebihara, T.; Enomoto, S.; Furuno, K.; Gando, Y.; Ikeda, H.; Inoue, K.; Kibe, Y.; Kishimoto, Y.; Koga, M.; Minekawa, Y.; Mitsui, T.; Nakajima, K.; Nakajima, K.; Nakamura, K.; Owada, K.; Shimizu, I.; Shimizu, Y.; Shirai, J.; Suekane, F.; Suzuki, A.; Tamae, K.; Yoshida, S.; Kozlov, A.; Murayama, H.; Grant, C.; Leonard, D. S.; Luk, K.-B.; Jillings, C.; Mauger, C.; McKeown, R. D.; Zhang, C.; Lane, C. E.; Maricic, J.; Miletic, T.; Batygov, M.; Learned, J. G.; Matsuno, S.; Pakvasa, S.; Foster, J.; Horton-Smith, G. A.; Tang, A.; Dazeley, S.; Downum, K. E.; Gratta, G.; Tolich, K.; Bugg, W.; Efremenko, Y.; Kamyshkov, Y.; Perevozchikov, O.; Karwowski, H. J.; Markoff, D. M.; Tornow, W.; Piquemal, F.; Ricol, J.-S.

    2009-03-05

    We have successfully built and operated a source deployment system for the KamLAND detector. This system was used to position radioactive sources throughout the delicate 1-kton liquid scintillator volume, while meeting stringent material cleanliness, material compatibility, and safety requirements. The calibration data obtained with this device were used to fully characterize detector position and energy reconstruction biases. As a result, the uncertainty in the size of the detector fiducial volume was reduced by a factor of two. Prior to calibration with this system, the fiducial volume was the largest source of systematic uncertainty in measuring the number of antineutrinos detected by KamLAND. This paper describes the design, operation and performance of this unique calibration system.

  15. Translation Invariant Extensions of Finite Volume Measures

    Science.gov (United States)

    Goldstein, S.; Kuna, T.; Lebowitz, J. L.; Speer, E. R.

    2017-02-01

    We investigate the following questions: Given a measure μ _Λ on configurations on a subset Λ of a lattice L, where a configuration is an element of Ω ^Λ for some fixed set Ω , does there exist a measure μ on configurations on all of L, invariant under some specified symmetry group of L, such that μ _Λ is its marginal on configurations on Λ ? When the answer is yes, what are the properties, e.g., the entropies, of such measures? Our primary focus is the case in which L=Z^d and the symmetries are the translations. For the case in which Λ is an interval in Z we give a simple necessary and sufficient condition, local translation invariance ( LTI), for extendibility. For LTI measures we construct extensions having maximal entropy, which we show are Gibbs measures; this construction extends to the case in which L is the Bethe lattice. On Z we also consider extensions supported on periodic configurations, which are analyzed using de Bruijn graphs and which include the extensions with minimal entropy. When Λ subset Z is not an interval, or when Λ subset Z^d with d>1, the LTI condition is necessary but not sufficient for extendibility. For Z^d with d>1, extendibility is in some sense undecidable.

  16. Translation Invariant Extensions of Finite Volume Measures

    Science.gov (United States)

    Goldstein, S.; Kuna, T.; Lebowitz, J. L.; Speer, E. R.

    2016-08-01

    We investigate the following questions: Given a measure μ _Λ on configurations on a subset Λ of a lattice L, where a configuration is an element of Ω ^Λ for some fixed set Ω , does there exist a measure μ on configurations on all of L, invariant under some specified symmetry group of L, such that μ _Λ is its marginal on configurations on Λ ? When the answer is yes, what are the properties, e.g., the entropies, of such measures? Our primary focus is the case in which L=Z^d and the symmetries are the translations. For the case in which Λ is an interval in Z we give a simple necessary and sufficient condition, local translation invariance (LTI), for extendibility. For LTI measures we construct extensions having maximal entropy, which we show are Gibbs measures; this construction extends to the case in which L is the Bethe lattice. On Z we also consider extensions supported on periodic configurations, which are analyzed using de Bruijn graphs and which include the extensions with minimal entropy. When Λ subset Z is not an interval, or when Λ subset Z^d with d>1 , the LTI condition is necessary but not sufficient for extendibility. For Z^d with d>1 , extendibility is in some sense undecidable.

  17. Measuring glioma volumes: A comparison of linear measurement based formulae with the manual image segmentation technique

    Directory of Open Access Journals (Sweden)

    Sanjeev A Sreenivasan

    2016-01-01

    Conclusions: Manual region of interest-based image segmentation is the standard technique for measuring glioma volumes. For routine clinical use, the simple formula v = abc/2 (or the formula for volume of an ellipsoid could be used as alternatives.

  18. Variation in Measurements of Transtibial Stump Model Volume A Comparison of Five Methods

    NARCIS (Netherlands)

    Bolt, A.; de Boer-Wilzing, V. G.; Geertzen, J. H. B.; Emmelot, C. H.; Baars, E. C. T.; Dijkstra, P. U.

    2010-01-01

    Objective: To determine the right moment for fitting the first prosthesis, it is necessary to know when the volume of the stump has stabilized. The aim of this study is to analyze variation in measurements of transtibial stump model volumes using the water immersion method, the Design TT system, the

  19. Transcutaneous measurement of volume blood flow

    Science.gov (United States)

    Daigle, R. E.; Mcleod, F. D.; Miller, C. W.; Histand, M. B.; Wells, M. K.

    1974-01-01

    Blood flow velocity measurements, using Doppler velocimeter, are described. The ability to measure blood velocity using ultrasound is derived from the Doppler effect; the change in frequency which occurs when sound is reflected or transmitted from a moving target. When ultrasound of the appropriate frequency is transmitted through a moving blood stream, the blood cells act as point scatterers of ultrasonic energy. If this scattered ultrasonic energy is detected, it is found to be shifted in frequency according to the velocity of the blood cells, nu, the frequency of the incident sound, f sub o, the speed of sound in the medium, c, and the angle between the sound beam and the velocity vector, o. The relation describing this effect is known as the Doppler equation. Delta f = 2 f sub o x nu x cos alpha/c. The theoretical and experimental methods are evaluated.

  20. The order and volume fill rates in inventory control systems

    DEFF Research Database (Denmark)

    Thorstenson, Anders; Larsen, Christian

    2011-01-01

    measure. The main result shows how the order and volume fill rates are related in magnitude. Earlier results derived for a single-item, single-stage, continuous review inventory system with backordering and constant lead times controlled by a base-stock policy are extended in different directions......This paper differentiates between an order (line) fill rate and a volume fill rate and specifies their performance for different inventory control systems. When the focus is on filling complete customer orders rather than total quantities the order fill rate would be the preferred service level...

  1. The order and volume fill rates in inventory control systems

    DEFF Research Database (Denmark)

    Thorstenson, Anders; Larsen, Christian

    2011-01-01

    This paper differentiates between an order (line) fill rate and a volume fill rate and specifies their performance for different inventory control systems. When the focus is on filling complete customer orders rather than total quantities the order fill rate would be the preferred service level...... measure. The main result shows how the order and volume fill rates are related in magnitude. Earlier results derived for a single-item, single-stage, continuous review inventory system with backordering and constant lead times controlled by a base-stock policy are extended in different directions...

  2. Measurement System & Calibration report

    DEFF Research Database (Denmark)

    Kock, Carsten Weber; Vesth, Allan

    This Measurement System & Calibration report is describing DTU’s measurement system installed at a specific wind turbine. A major part of the sensors has been installed by others (see [1]) the rest of the sensors have been installed by DTU. The results of the measurements, described in this report...

  3. Analysis of Partial Volume Effects on Accurate Measurement of the Hippocampus Volume

    Institute of Scientific and Technical Information of China (English)

    Maryam Hajiesmaeili; Jamshid Dehmeshki; Tim Ellis

    2014-01-01

    Hippocampal volume loss is an important biomarker in distinguishing subjects with Alzheimer’s disease (AD) and its measurement in magnetic resonance images (MRI) is influenced by partial volume effects (PVE). This paper describes a post-processing approach to quantify PVE for correction of the hippocampal volume by using a spatial fuzzyC-means (SFCM) method. The algorithm is evaluated on a dataset of 20 T1-weighted MRI scans sampled at two different resolutions. The corrected volumes for left and right hippocampus (HC) which are 23% and 18% for the low resolution and 6% and 5% for the high resolution datasets, respectively are lower than hippocampal volume results from manual segmentation. Results show the importance of applying this technique in AD detection with low resolution datasets.

  4. The order and volume fill rates in inventory control systems

    DEFF Research Database (Denmark)

    Thorstenson, Anders; Larsen, Christian

    2014-01-01

    level measure. The main result shows how the order and volume fill rates are related in magnitude. Earlier results derived for a single-item, single-stage, continuous review inventory system with backordering and constant lead times controlled by a base-stock policy are extended in different directions......This paper differentiates between an order (line) fill rate and a volume fill rate and specifies their performance for different inventory control systems. When the focus is on filling complete customer orders rather than total demanded quantity the order fill rate would be the preferred service...... extensions consider more general inventory control review policies with backordering, as well as some relations between service measures. A particularly important result in the paper concerns an alternative service measure, the customer order fill rate, and shows how this measure always exceeds the other two...

  5. Accurate monitoring of intravascular fluid volume: A novel application of intrathoracic impedance measures for the guidance of volume reduction therapy

    Directory of Open Access Journals (Sweden)

    Barbara A. Lara

    2015-09-01

    Conclusion: Impedance vectors derived from a multivector monitoring system reflect changes in intravascular plasma volume. Two of these vectors most closely track changes in plasma volume and may be used to more accurately guide and optimize volume reduction therapy.

  6. Systemic risk measures

    Science.gov (United States)

    Guerra, Solange Maria; Silva, Thiago Christiano; Tabak, Benjamin Miranda; de Souza Penaloza, Rodrigo Andrés; de Castro Miranda, Rodrigo César

    2016-01-01

    In this paper we present systemic risk measures based on contingent claims approach and banking sector multivariate density. We also apply network measures to analyze bank common risk exposure. The proposed measures aim to capture credit risk stress and its potential to become systemic. These indicators capture not only individual bank vulnerability, but also the stress dependency structure between them. Furthermore, these measures can be quite useful for identifying systemically important banks. The empirical results show that these indicators capture with considerable fidelity the moments of increasing systemic risk in the Brazilian banking sector in recent years.

  7. Health System Measurement Project

    Data.gov (United States)

    U.S. Department of Health & Human Services — The Health System Measurement Project tracks government data on critical U.S. health system indicators. The website presents national trend data as well as detailed...

  8. Measuring industrial energy efficiency: Physical volume versus economic value

    Energy Technology Data Exchange (ETDEWEB)

    Freeman, S.L.; Niefer, M.J.; Roop, J.M.

    1996-12-01

    This report examines several different measures of industrial output for use in constructing estimates of industrial energy efficiency and discusses some reasons for differences between the measures. Estimates of volume-based measures of output, as well as 3 value-based measures of output (value of production, value of shipments, and value added), are evaluated for 15 separate 4-digit industries. Volatility, simple growth rate, and trend growth rate estimates are made for each industry and each measure of output. Correlations are made between the volume- and value-based measures of output. Historical energy use data are collected for 5 of the industries for making energy- intensity estimates. Growth rates in energy use, energy intensity, and correlations between volume- and value-based measures of energy intensity are computed. There is large variability in growth trend estimates both long term and from year to year. While there is a high correlation between volume- and value-based measures of output for a few industries, typically the correlation is low, and this is exacerbated for estimates of energy intensity. Analysis revealed reasons for these low correlations. It appears that substantial work must be done before reliable measures of trends in the energy efficiency of industry can be accurately characterized.

  9. Measuring Systemic Risk

    DEFF Research Database (Denmark)

    Acharya, Viral V.; Heje Pedersen, Lasse; Philippon, Thomas

    We present a simple model of systemic risk and we show that each financial institution's contribution to systemic risk can be measured as its systemic expected shortfall (SES), i.e., its propensity to be undercapitalized when the system as a whole is undercapitalized. SES increases...

  10. A STUDY ON MORPHOMETRIC MEASUREMENT OF VOLUME OF ACETABULUM

    Directory of Open Access Journals (Sweden)

    Leena Khobragade,

    2014-09-01

    Full Text Available Background: Hip joint represents an unique functional unit and has complex biomechanical construction. In today’s era where total hip replacement surgeries have made their way it has become imperative for the anatomists to know the variations in acetabular dimensions. Reconstruction of acetabulum in patients with significant acetabular bone deficiency remains a challenge. Hence the present study was carried out with the aim to study the morphometric measurement of volume of acetabulum in both the sexes. Materials and Methods: Material of the study consisted of 110 human hip bones (60 males and 50 females. Volume of Acetabulum (VA was measured on these hip bones on both the sides. Statistical analysis was done using SPSS (Statistical Package for the Social Sciences version 11 and Microsoft Excel 2007. Results: The mean volume of acetabulum in male was 23.13 ml and female was 17.88 ml. The mean volume of acetabulum on right side was 20.55 ml and left side was 20.91 ml. Volume of the acetabulum was greater in males as compared to females and the differences were statistically significant. Volume was greater on the left side as compared to the right side but the difference was statistically non significant. Discussion: Analysing the differences on human acetabulum is helpful in understanding not only morphological but also medicolegal aspects. Conclusion: Volume of the acetabulum was greater in males as compared to females.

  11. The bigger, the better? Volume measurements of parasites and hosts

    DEFF Research Database (Denmark)

    Nagler, Christina; Hörnig, Marie K.; Haug, Joachim T.

    2017-01-01

    . Using advanced imaging methods (micro-CT in conjunction with 3D modeling), we measured the volume of parasitic structures (externa, interna, egg mass, egg number, visceral mass) and the volume of the entire host. Our results show positive correlations between the volume of (1) entire rhizocephalan...... (externa + interna) and host body, (2) rhizocephalan externa and host body, (3) rhizocephalan visceral mass and rhizocephalan body, (4) egg mass and rhizocephalan externa, (5) rhizocephalan egg mass and their egg number. Comparing the rhizocephalan Sylon hippolytes, a parasite of caridean shrimps...

  12. Quantifying Volume Changing Perturbations in a Wave Chaotic System

    CERN Document Server

    Taddese, Biniyam Tesfaye; Moglie, Franco; Antonsen, Thomas M; Ott, Edward; Anlage, Steven M

    2012-01-01

    A sensor was developed to quantitatively measure perturbations which change the volume of a wave chaotic cavity while leaving its shape intact. The sensors work in the time domain by using either scattering fidelity of the transmitted signals or the classical analog of the Loschmidt echo. The sensors were tested experimentally by inducing volume changing perturbations to a one cubic meter pseudo-integrable, real-world cavity. Perturbations which caused a volume change that is as small as 54 parts in a million were quantitatively measured. These results were obtained by using electromagnetic waves with a wavelength of about $5cm$, therefore, the sensor is sensitive to extreme sub-wavelength changes of the boundaries of a cavity. The experimental results were compared with Finite Difference Time Domain (FDTD) simulation results, and good agreement was found. Furthermore, the sensor was tested using a frequency domain approach on a numerical model of the star graph, which is a representative wave chaotic system....

  13. Method for measuring anterior chamber volume by image analysis

    Science.gov (United States)

    Zhai, Gaoshou; Zhang, Junhong; Wang, Ruichang; Wang, Bingsong; Wang, Ningli

    2007-12-01

    Anterior chamber volume (ACV) is very important for an oculist to make rational pathological diagnosis as to patients who have some optic diseases such as glaucoma and etc., yet it is always difficult to be measured accurately. In this paper, a method is devised to measure anterior chamber volumes based on JPEG-formatted image files that have been transformed from medical images using the anterior-chamber optical coherence tomographer (AC-OCT) and corresponding image-processing software. The corresponding algorithms for image analysis and ACV calculation are implemented in VC++ and a series of anterior chamber images of typical patients are analyzed, while anterior chamber volumes are calculated and are verified that they are in accord with clinical observation. It shows that the measurement method is effective and feasible and it has potential to improve accuracy of ACV calculation. Meanwhile, some measures should be taken to simplify the handcraft preprocess working as to images.

  14. Finding the Density of Objects without Measuring Mass and Volume

    Science.gov (United States)

    Mumba, Frackson; Tsige, Mesfin

    2007-01-01

    A simple method based on the moment of forces and Archimedes' principle is described for finding density without measuring the mass and volume of an object. The method involves balancing two unknown objects of masses M[subscript 1] and M[subscript 2] on each side of a pivot on a metre rule and measuring their corresponding moment arms. The object…

  15. Critical Evaluation of Blood Volume Measurements during Hemodialysis

    NARCIS (Netherlands)

    Dasselaar, Judith J.; van der Sande, Frank M.; Franssen, Casper F. M.

    2012-01-01

    Devices that continuously measure relative blood volume (RBV) changes during hemodialysis (HD) are increasingly used for the prevention of dialysis hypotension and fine-tuning of dry weight. However, RBV measurements are subject to various limitations. First, RBV devices provide information on relat

  16. A liquid-independent volume flow measurement principle

    NARCIS (Netherlands)

    Geers, L.F.G.; Volker, A.W.F.; Hunter, T.P.M.

    2010-01-01

    A novel flow measurement principle is presented enabling non-intrusive volume flow measurements of liquids in the ml/min range. It is based on an opto-acoustical time-of-flight principle, where the time interval is recorded in which a thermal label travels a known distance through a flow channel. Bi

  17. Feasibility of the left ventricular volume measurement by acoustic quantification method. Comparison with ultrafast computed tomography

    Energy Technology Data Exchange (ETDEWEB)

    Tomimoto, Shigehiro; Nakatani, Satoshi; Tanaka, Norio; Uematsu, Masaaki; Beppu, Shintaro; Nagata, Seiki; Hamada, Seiki; Takamiya, Makoto; Miyatake, Kunio [National Cardiovascular Center, Suita, Osaka (Japan)

    1995-01-01

    Acoustic quantification (AQ: the real-time automated boundary detection system) allows instantaneous measurement of cardiac chamber volumes. The feasibility of this method was evaluated by comparing the left ventricular (LV) volumes obtained with AQ to those derived from ultrafast computed tomography (UFCT), which enables accurate measurements of LV volumes even in the presence of LV asynergy, in 23 patients (8 with ischemic heart disease, 5 with cardiomyopathy, 3 with valvular heart disease). Both LV end-diastolic and end-systolic volumes obtained with the AQ method were in good agreement with those obtained with UFCT (y=1.04{chi}-16.9, r=0.95; y=0.87{chi}+15.7, r=0.91; respectively). AQ was reliable even in the presence of LV asynergy. Interobserver variability for the AQ measurement was 10.2%. AQ provides a new, clinically useful method for real-time accurate estimation of the left ventricular volume. (author).

  18. Measurement and determinants of infrarenal aortic thrombus volume

    Energy Technology Data Exchange (ETDEWEB)

    Golledge, Jonathan; Wolanski, Philippe [James Cook University, The Vascular Biology Unit, Townsville, Queensland (Australia); Townsville Hospital, Townsville, Queensland (Australia); Parr, Adam [James Cook University, The Vascular Biology Unit, Townsville, Queensland (Australia); Buttner, Petra [James Cook University, School of Public Health and Tropical Medicine, Townsville, Queensland (Australia)

    2008-09-15

    Intra-luminal thrombus has been suggested to play a role in the progression of abdominal aortic aneurysm (AAA). The aims of this study were twofold. Firstly, to assess the reproducibility of a computer tomography (CT)-based technique for measurement of aortic thrombus volume. Secondly, to examine the determinants of infrarenal aortic thrombus volume in a cohort of patients with aortic dilatation. A consecutive series of 75 patients assessed by CT angiography with maximum aortic diameter {>=}25 mm were recruited. Intra-luminal thrombus volume was measured by a semi-automated workstation protocol based on a previously defined technique to quantitate aortic calcification. Intra- and inter-observer reproducibility were assessed using correlation coefficients, coefficient of variation and Bland-Altman plots. Infrarenal aortic thrombus volume percentage was related to clinical, anatomical and blood characteristics of the patients using univariate and multivariate tests. Infrarenal aortic thrombus volume was related to the severity of aortic dilatation assessed by total aortic volume (r=0.87, P<0.0001) or maximum aortic diameter (r=0.74, P< 0.0001). We therefore examined the clinical determinates of aortic thrombus expressed as a percentage of total aortic volume. Aortic thrombus percentage was negatively correlated with serum high density lipoprotein (HDL, r=-0.31). By ordinal multiple logistic regression analysis serum HDL below median ({<=}1.2 mM) was associated with aortic thrombus percentage in the upper quartile adjusting for other risk factors (odds ratio 5.3, 95% CI 1.1-25.0). Infrarenal aortic thrombus volume can be measured reproducibly on CT. Serum HDL, which can be therapeutically raised, may play a role in discouraging aortic thrombus accumulation with implications in terms of delaying progression of AAA. (orig.)

  19. Measuring Systemic Risk

    DEFF Research Database (Denmark)

    Acharya, Viral V.; Heje Pedersen, Lasse; Philippon, Thomas

    2017-01-01

    We present an economic model of systemic risk in which undercapitalization of the financial sector as a whole is assumed to harm the real economy, leading to a systemic risk externality. Each financial institution’s contribution to systemic risk can be measured as its systemic expected shortfall...... of components of SES to predict emerging systemic risk during the financial crisis of 2007–2009....

  20. Monte Carlo method with heuristic adjustment for irregularly shaped food product volume measurement.

    Science.gov (United States)

    Siswantoro, Joko; Prabuwono, Anton Satria; Abdullah, Azizi; Idrus, Bahari

    2014-01-01

    Volume measurement plays an important role in the production and processing of food products. Various methods have been proposed to measure the volume of food products with irregular shapes based on 3D reconstruction. However, 3D reconstruction comes with a high-priced computational cost. Furthermore, some of the volume measurement methods based on 3D reconstruction have a low accuracy. Another method for measuring volume of objects uses Monte Carlo method. Monte Carlo method performs volume measurements using random points. Monte Carlo method only requires information regarding whether random points fall inside or outside an object and does not require a 3D reconstruction. This paper proposes volume measurement using a computer vision system for irregularly shaped food products without 3D reconstruction based on Monte Carlo method with heuristic adjustment. Five images of food product were captured using five cameras and processed to produce binary images. Monte Carlo integration with heuristic adjustment was performed to measure the volume based on the information extracted from binary images. The experimental results show that the proposed method provided high accuracy and precision compared to the water displacement method. In addition, the proposed method is more accurate and faster than the space carving method.

  1. Truck Loaded Sand and Gravel Volume Measuring System Based on Laser Range%基于激光测距的车载沙石体积测量系统

    Institute of Scientific and Technical Information of China (English)

    吉华; 戴健伟; 孔令钊; 岳显; 樊刚

    2013-01-01

    车载沙石的体积测量对于控制混凝土的生产成本以及质量都具有重要意义.在系统中,x-y平面旋转和y-z平面偏转配合工作机构实现了一个激光测距仪对沙石表面扫描测量,延时策略简单有效地保证了电机运动和激光测距的协同工作,边界判断方法能有效地筛除测量过程中产生的无效数据.工业应用表明:采用机械、测控、软件技术实现的车载沙石体积测量系统能够解决车载沙石的体积测量问题.%The sand and gravel are main raw materials of ready-mixed concrete which is basic material for national construction. The volume measurement of truck loaded sand and gravel is important for the quality and costs control of ready-mixed concrete. In this system,the mechanism of x-y plane rotation cooperative with z-direction deflection realized that one laser range instrument scaned the sand and gravel surface,and the delay strategy made the motor motion and range measurement working together simply and efficiently, and boundary determination strategy removes the invalid measuring data efficiently. The appellation cases show that the system,which is implemented by making use of mechanics,control and measurement,software technology synthetically , can measure the volume of the truck loaded sand and gravel accurately.

  2. Reliability of brain volume measurements: a test-retest dataset.

    Science.gov (United States)

    Maclaren, Julian; Han, Zhaoying; Vos, Sjoerd B; Fischbein, Nancy; Bammer, Roland

    2014-01-01

    Evaluation of neurodegenerative disease progression may be assisted by quantification of the volume of structures in the human brain using magnetic resonance imaging (MRI). Automated segmentation software has improved the feasibility of this approach, but often the reliability of measurements is uncertain. We have established a unique dataset to assess the repeatability of brain segmentation and analysis methods. We acquired 120 T1-weighted volumes from 3 subjects (40 volumes/subject) in 20 sessions spanning 31 days, using the protocol recommended by the Alzheimer's Disease Neuroimaging Initiative (ADNI). Each subject was scanned twice within each session, with repositioning between the two scans, allowing determination of test-retest reliability both within a single session (intra-session) and from day to day (inter-session). To demonstrate the application of the dataset, all 3D volumes were processed using FreeSurfer v5.1. The coefficient of variation of volumetric measurements was between 1.6% (caudate) and 6.1% (thalamus). Inter-session variability exceeded intra-session variability for lateral ventricle volume (P<0.0001), indicating that ventricle volume in the subjects varied between days.

  3. The orbital volume measurement in patients with ventriculoperitoneal shunt.

    Science.gov (United States)

    Kim, Jong-Min; Chang, Moo-Hwan; Kyung, Sungeun E

    2015-01-01

    Enophthalmos occurs from the increased bony volume or decreased soft tissue volume in the orbit and can be caused in patients with long-term ventriculoperitoneal (VP) shunt. This study tried to find out the change of orbital volume by measuring the orbital volume before and after operation in adult patients who underwent VP shunt for hydrocephalus. The 2 evaluators measured orbital volume by using ITK-SNAP 2.4 program with double-blind test for computed tomography images before and after operation targeting 36 patients over the age of 18 who underwent VP shunt with pressure-controlled valve from 2003 to 2011. Wilcoxon matched-pairs signed-rank test of GraphPad software was used to statistically analyze the difference in orbital volume change before and after operation. In case of mean pre-op orbital volume of total 36 patients, the right was measured as 23.72 ± 4.65 cm(3), the left as 23.47 ± 4.61 cm(3), the post-op right as 24.67 ± 4.70 cm(3), and the left as 24.18 ± 4.63 cm(3), showing no statistically significant difference (P = 0.106). The mean pre-op orbital volume of 14 people (28 eyes) followed for more than 11 months was 25.06 ± 4.58 cm(3) in the right and 24.4 ± 5.02 cm(3) in the left and the mean post-op orbital volume was 27.0 ± 4.28 cm(3) in the right and 25.76 ± 3.92 cm(3) in the left, showing statistically significant differences in the change of the volume before and after shunt operation (P = 0.0057). In patients who maintain long-term shunt devices after VP shunt, remodeling of matured orbital bone may be caused due to the change in pressure gradient between cranial cavity and orbit and the possible occurrence of resulting secondary enophthalmos by increased orbital volume should be considered.

  4. Comparative technique in measurements of Ge detectors effective volumes

    Science.gov (United States)

    Demidova, E. V.; Kirpichnikov, I. V.; Vasenko, A. A.

    1999-01-01

    A simple and quick procedure was proposed for measurements of large coaxial Ge detectors effective volumes. It included a comparison of background spectra collected with several detectors without any shielding in an underground laboratory. Such measurements were performed in Homestake (USA) and Canfranc (Spain) laboratories with several 1 kg and 2 kg detectors. Monte-Carlo calculations confirmed that ratios of numbers of events in continua of the spectra should be either equal or very close to the ratios of the detectors effective volumes.

  5. New photosensitive systems for volume phase holography

    Science.gov (United States)

    Bianco, Andrea; Colella, Letizia; Galli, Paola; Zanutta, Alessio; Bertarelli, Chiara

    2017-05-01

    Volume phase holographic elements are becoming attractive thanks to the large efficiency and good optical quality. They are based on photosensitive materials where a modulation of the refractive index is induced. In this paper, we highlight the strategies to obtain a change in the refractive index in a dielectric material, namely a change in the material density and/or in the molecular polarizability. Moreover, we show the results achieved for materials that undergo the photo-Fries reaction as function of the molecular structure and the illumination conditions. We also report the results on a system based on the diazo Meldrum's acid where volatile molecules are produced upon light exposure.

  6. Representative volume element of asphalt pavement for electromagnetic measurements

    Directory of Open Access Journals (Sweden)

    Terhi Pellinen

    2015-02-01

    Full Text Available The motivation for this study was to investigate the representative volume element (RVE needed to correlate the nondestructive electromagnetic (EM measurements with the conventional destructive asphalt pavement quality control measurements. A large pavement rehabilitation contract was used as the test site for the experiment. Pavement cores were drilled from the same locations where the stationary and continuous Ground Penetrating Radar (GPR measurements were obtained. Laboratory measurements included testing the bulk density of cores using two methods, the surface-saturated dry method and determining bulk density by dimensions. Also, Vector Network Analyzer (VNA and the through specimen transmission configuration were employed at microwave frequencies to measure the reference dielectric constant of cores using two different footprint areas and therefore volume elements. The RVE for EM measurements turns out to be frequency dependent; therefore in addition to being dependent on asphalt mixture type and method of obtaining bulk density, it is dependent on the resolution of the EM method used. Then, although the average bulk property results agreed with theoretical formulations of higher core air void content giving a lower dielectric constant, for the individual cores there was no correlation for the VNA measurements because the volume element seizes deviated. Similarly, GPR technique was unable to capture the spatial variation of pavement air voids measured from the 150-mm drill cores. More research is needed to determine the usable RVE for asphalt.

  7. Utilising Geological Field Measurements and Historic Eruption Volumes to Estimate the Volume of Santorini's Magma Chamber

    Science.gov (United States)

    Browning, J.; Drymoni, K.; Gudmundsson, A.

    2015-12-01

    An understanding of the amount of magma available to supply any given eruption is useful for determining the potential eruption magnitude and duration. Geodetic measurements and inversion techniques are often used to constrain volume changes within magma chambers, as well as constrain location and depth, but such models are incapable of calculating total magma storage. For example, during the 2012 unrest period at Santorini volcano, approximately 0.021 km3 of new magma entered a shallow chamber residing at around 4 km below the surface. This type of event is not unusual, and is in fact a necessary condition for the formation of a long-lived shallow chamber, of which Santorini must possess. The period of unrest ended without culminating in eruption, i.e the amount of magma which entered the chamber was insufficient to break the chamber and force magma further towards the surface. We combine previously published data on the volume of recent eruptions at Santorini together with geodetic measurements. Measurements of dykes within the caldera wall provide an estimate of the volume of magma transported during eruptions, assuming the dyke does not become arrested. When the combined volume of a dyke and eruption are known (Ve) they can be used to estimate using fracture mechanics principles and poro-elastic constraints the size of an underlying shallow magma chamber. We present field measurements of dykes within Santorini caldera and provide an analytical method to estimate the volume of magma contained underneath Santorini caldera. In addition we postulate the potential volume of magma required as input from deeper sources to switch the shallow magma chamber from an equilibrium setting to one where the pressure inside the chamber exceeds the surrounding host rocks tensile strength, a condition necessary to form a dyke and a possible eruption.

  8. Electrochemical thermodynamic measurement system

    Science.gov (United States)

    Reynier, Yvan; Yazami, Rachid; Fultz, Brent T.

    2009-09-29

    The present invention provides systems and methods for accurately characterizing thermodynamic and materials properties of electrodes and electrochemical energy storage and conversion systems. Systems and methods of the present invention are configured for simultaneously collecting a suite of measurements characterizing a plurality of interconnected electrochemical and thermodynamic parameters relating to the electrode reaction state of advancement, voltage and temperature. Enhanced sensitivity provided by the present methods and systems combined with measurement conditions that reflect thermodynamically stabilized electrode conditions allow very accurate measurement of thermodynamic parameters, including state functions such as the Gibbs free energy, enthalpy and entropy of electrode/electrochemical cell reactions, that enable prediction of important performance attributes of electrode materials and electrochemical systems, such as the energy, power density, current rate and the cycle life of an electrochemical cell.

  9. Reliability and Accuracy of Brain Volume Measurement on MR Imaging

    DEFF Research Database (Denmark)

    Yamagchii, Kechiro; Lassen, Anders; Ring, Poul

    1998-01-01

    Yamaguchi, K., Lassen, A. And Ring, P. Reliability and Accuracy of Brain Volume Measurement on MR Imaging. Abstract at ESMRMB98 European Society for Magnetic Resonance in Medicine and Biology, Geneva, Sept 17-20, 1998 Danish Research Center for Magnetic Resonance, Hvidovre University Hospital...

  10. Measurement System Reliability Assessment

    Directory of Open Access Journals (Sweden)

    Kłos Ryszard

    2015-06-01

    Full Text Available Decision-making in problem situations is based on up-to-date and reliable information. A great deal of information is subject to rapid changes, hence it may be outdated or manipulated and enforce erroneous decisions. It is crucial to have the possibility to assess the obtained information. In order to ensure its reliability it is best to obtain it with an own measurement process. In such a case, conducting assessment of measurement system reliability seems to be crucial. The article describes general approach to assessing reliability of measurement systems.

  11. Measuring Systemic Risk

    DEFF Research Database (Denmark)

    Acharya, Viral V.; Heje Pedersen, Lasse; Philippon, Thomas

    We present a simple model of systemic risk and we show that each financial institution's contribution to systemic risk can be measured as its systemic expected shortfall (SES), i.e., its propensity to be undercapitalized when the system as a whole is undercapitalized. SES increases...... with the institution's leverage and with its expected loss in the tail of the system's loss distribution. Institutions internalize their externality if they are ‘taxed’ based on their SES. We demonstrate empirically the ability of SES to predict emerging risks during the financial crisis of 2007-2009, in particular...

  12. On-line dynamic measurement of blood viscosity, hematocrit and change of blood volume

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    Objective: To develop an on-line system for the measurement of blood viscosity and hematocrit. The dynamic changes of the macrovascular blood volumes,microvascular blood volumes and the total blood volume were observed by means of calculating from the testing result. Methods: Applying traditional viscosity measurement principle and specific wavelength optic density measurement method, an on-line system for the measurement of blood viscosity and hematocrit was developed, and the A/D multifunctionai board and the testing circuit were designed by ourselves. The system was validated by experiments both in vitro and in vivo. Therapeutic effects of hypertonic saline dextran solution (HSD) and Lactatic Ringer's solution at the early stage after burn-blast combined injury were compared by this method. Results: The results showed that the system has attained the goal of the design. The changes of the blood viscosity and hematocrit could be detected effectively and continuously. The changes of macrovascular, microvascular and total blood volume could be calculated approximately. Conclusions: The system and the method can continuously on-line test the blood viscosity and hematocrit, and reveal the change and distribution of blood volumes more accurately and dearly in the therapy process by estimating changes of the macrovascular, microvascular and total blood volumes, respectively. It has confirmed that HSD treatment could increase blood pressure and attenuate tissue edema by significantly increasing total blood volume,improving macrocirculatory and microcirculatory blood volumes. This study suggested that it could be desirable to develop an experiment technique based on the method mentioned above.

  13. Gastric residual volume (GRV) and gastric contents measurement by refractometry.

    Science.gov (United States)

    Chang, Wei-Kuo; McClave, Stephen A; Hsieh, Chung-Bao; Chao, You-Chen

    2007-01-01

    Traditional use of gastric residual volumes (GRVs), obtained by aspiration from a nasogastric tube, is inaccurate and cannot differentiate components of the gastric contents (gastric secretion vs delivered formula). The use of refractometry and 3 mathematical equations has been proposed as a method to calculate the formula concentration, GRV, and formula volume. In this paper, we have validated these mathematical equations so that they can be implemented in clinical practice. Each of 16 patients receiving a nasogastric tube had 50 mL of water followed by 100 mL of dietary formula (Osmolite HN, Abbott Laboratories, Columbus, OH) infused into the stomach. After mixing, gastric content was aspirated for the first Brix value (BV) measurement by refractometry. Then, 50 mL of water was infused into the stomach and a second BV was measured. The procedure of infusion of dietary formula (100 mL) and then water (50 mL) was repeated and followed by subsequent BV measurement. The same procedure was performed in an in vitro experiment. Formula concentration, GRV, and formula volume were calculated from the derived mathematical equations. The formula concentrations, GRVs, and formula volumes calculated by using refractometry and the mathematical equations were close to the true values obtained from both in vivo and in vitro validation experiments. Using this method, measurement of the BV of gastric contents is simple, reproducible, and inexpensive. Refractometry and the derived mathematical equations may be used to measure formula concentration, GRV, and formula volume, and also to serve as a tool for monitoring the gastric contents of patients receiving nasogastric feeding.

  14. CIRMIS Data system. Volume 2. Program listings

    Energy Technology Data Exchange (ETDEWEB)

    Friedrichs, D.R.

    1980-01-01

    The Assessment of Effectiveness of Geologic Isolation Systems (AEGIS) Program is developing and applying the methodology for assessing the far-field, long-term post-closure safety of deep geologic nuclear waste repositories. AEGIS is being performed by Pacific Northwest Laboratory (PNL) under contract with the Office of Nuclear Waste Isolation (OWNI) for the Department of Energy (DOE). One task within AEGIS is the development of methodology for analysis of the consequences (water pathway) from loss of repository containment as defined by various release scenarios. Analysis of the long-term, far-field consequences of release scenarios requires the application of numerical codes which simulate the hydrologic systems, model the transport of released radionuclides through the hydrologic systems, model the transport of released radionuclides through the hydrologic systems to the biosphere, and, where applicable, assess the radiological dose to humans. The various input parameters required in the analysis are compiled in data systems. The data are organized and prepared by various input subroutines for utilization by the hydraulic and transport codes. The hydrologic models simulate the groundwater flow systems and provide water flow directions, rates, and velocities as inputs to the transport models. Outputs from the transport models are basically graphs of radionuclide concentration in the groundwater plotted against time. After dilution in the receiving surface-water body (e.g., lake, river, bay), these data are the input source terms for the dose models, if dose assessments are required.The dose models calculate radiation dose to individuals and populations. CIRMIS (Comprehensive Information Retrieval and Model Input Sequence) Data System is a storage and retrieval system for model input and output data, including graphical interpretation and display. This is the second of four volumes of the description of the CIRMIS Data System.

  15. Impact of the Implementation of ESA 2010 on Volume Measurement

    Directory of Open Access Journals (Sweden)

    Petr Musil

    2016-06-01

    Full Text Available Volume indices are connected with statistical deflation that means recalculation of macro-aggregates to constant prices. Price calculations have to follow changes in definition or delineation of macro-aggregates. New standards of National Accounts (SNA 2008, ESA 2010 respectively bring many changes that should be taken into account in volume measures. The aim of this paper is to present new methods of deflation that respekt updated definitions and principles. Concept of foreign trade has been changed significantly as globalization is going faster and faster. Re-export and merchanting have become more important especially in small open economies such as the Czech Republic. This phenomenon should be reflected in constant prices calculations. Changes in methodology have also affected volume indices.

  16. Measurement of Gallbladder Volume with Ultrasonography in Pregnant Women

    Directory of Open Access Journals (Sweden)

    Sait Kapicioglu

    2000-01-01

    Full Text Available Fasting and postprandial gallbladder volumes were investigated using ultrasonography in three groups (10 subjects in each of healthy women: third trimester pregnant women, postpartum women up to 10 days after giving birth and nonpregnant controls. The scans were performed at 09:00 after a 12 h fast. After the basal measurement was taken, gallbladder volumes were rescanned in 15 min intervals for 60 mins. At the end of this period, all volunteers received a standard liquid test meal, and scans were performed again for 1 h. The mean basal gallbladder volume was 22.2±4.2 mL in the nonpregnant (control group. In the third trimester group, the basal volume was 37.8±10.5 mL – 70.5% higher than in the nonpregnant group (P<0.001. In the postpartum group, the mean basal volume was 37.9% lower (27.4±6.5 mL than that of the third trimester group (P<0.02. This basal volume was 23.6% greater than that of the control group (P<0.05. After administration of a test meal, the postprandial gallbladder volumes decreased during the first few minutes compared with baseline values. The volumes decreased by 10.2% to 39.8% (23.5±7.3 to 34.0±10.2; P<0.01 in the third trimester group, by 14.9% to 43.2% (16.6±4.3 to 23.3±5.5; P<0.01, 0.001 in the postpartum group and by 19.2% to 51.6% (11.9±3.5 to 17.9±3.6; P<0.02, 0.05, 0.01, 0.001 in the control group. Postprandial mean gallbladder volumes of the third trimester (P<0.02 and postpartum groups (P<0.02 to 0.01 were significantly different from those of the control group. In conclusion, incomplete emptying of the gallbladder after eating during the third trimester of pregnancy may contribute to cholesterol-gallstone formation, and pregnancy may thus increase the risk of gallstones.

  17. Measurement of cell volume changes by fluorescence self-quenching

    DEFF Research Database (Denmark)

    Hamann, Steffen; Kiilgaard, J.F.; Litman, Thomas

    2002-01-01

    At high concentrations, certain fluorophores undergo self-quenching, i.e., fluorescence intensity decreases with increasing fluorophore concentration. Accordingly, the self-quenching properties can be used for measuring water volume changes in lipid vesicles. In cells, quantitative determination...... of water transport using fluorescence self-quenching has been complicated by the requirement of relatively high (mM) and often toxic loading concentrations. Here we report a simple method that uses low (muM) loading concentrations of calcein-acetoxymethyl ester (calcein-AM) to obtain intracellular...... concentrations of the fluorophore calcein suitable for measurement of changes in cell water volume by self-quenching. The relationship between calcein fluorescence intensity, when excited at 490 nm (its excitation maximum), and calcein concentration was investigated in vitro and in various cultured cell types...

  18. Comparison of aerosol volume size distributions between column and surface measurements downwind of Seoul, Korea

    Science.gov (United States)

    Park, J. S.; Choi, Y.; Ghim, Y. S.

    2015-12-01

    The aerosol volume size distribution is one of the most important parameters in retrieving aerosol optical properties and studying radiative forcing. The column-integrated aerosol volume size distribution for AERONET was obtained from inversion product level 1.5 (22 bins between 0.1 and 30 μm in diameter) from the measurements of CIMEL sunphotometer (CE-318); that for SKYNET was obtained using skyrad.pack V5 (20 bins, 0.02-33 μm) from the measurements of PREDE skyradiometer (POM-02). The aerosol volume size distribution at the surface was measured using a wide range aerosol spectrometer system consisting of a scanning mobility particle scanner (Grimm, Model 5.419; 89 bins, 0.005-0.35 μm) and an optical particle counter (Grimm, Model 1.109; 31 bins, 0.27-34 μm). The measurement was conducted in Yongin, downwind of Seoul, Korea, from April 30 to June 27, 2015. The measurement site is located on the rooftop of a five-story building on the hill (37.34°N, 127.27°E, 167 m above sea level) in the global campus of Hankuk University of Foreign Studies. To investigate the discrepancy in effective diameter and fine mode volume fraction, we compared the volume size distributions when the measurement time coincided within 5 minutes because the measurement intervals were different between instruments.

  19. Effect of volume expansion on systemic hemodynamics and central and arterial blood volume in cirrhosis

    DEFF Research Database (Denmark)

    Møller, Søren; Bendtsen, Flemming; Henriksen, Jens Henrik

    1995-01-01

    and in controls. METHODS: Thirty-nine patients with cirrhosis (12 patients with Child-Turcotte class A, 14 with class B, and 13 with class C) and 6 controls were studied. During hepatic vein catheterization, cardiac output, systemic vascular resistance, central and arterial blood volume, noncentral blood volume...... in patients with either class B or class C. Conversely, the noncentral blood volume increased in patients with class B and C. In both patients and controls, the cardiac output increased and the systemic vascular resistance decreased, whereas the mean arterial blood pressure did not change significantly......BACKGROUND & AIMS: Systemic vasodilatation in cirrhosis may lead to hemodynamic alterations with reduced effective blood volume and decreased arterial blood pressure. This study investigates the response of acute volume expansion on hemodynamics and regional blood volumes in patients with cirrhosis...

  20. Measuring Systemic Risk

    DEFF Research Database (Denmark)

    Heje Pedersen, Lasse

    We present a simple model of systemic risk and we show that each financial institution’s contribution to systemic risk can be measured as its systemic expected shortfall (SES), i.e., its propensity to be undercapitalized when the system as a whole is undercapitalized. SES increases...... with the institution’s leverage and with its expected loss in the tail of the system’s loss distribution. Institutions internalize their externality if they are “taxed” based on their SES. We demonstrate empirically the ability of SES to predict emerging risks during the financial crisis of 2007-2009, in particular......, (i) the outcome of stress tests performed by regulators; (ii) the decline in equity valuations of large financial firms in the crisis; and, (iii) the widening of their credit default swap spreads....

  1. Automatic measurement of orbital volume in unilateral coronal synostosis

    DEFF Research Database (Denmark)

    Dahl, Vedrana Andersen; Einarsson, Gudmundur; Darvann, Tron Andre;

    2016-01-01

    Premature fusion of the coronal suture on one side of the calvaria (unilateral coronal synostosis, UCS) results in asymmetric craniofacial development and the deformation of the orbits. Often this necessitates surgery, where CT scanning is employed to obtain measures of the bony orbit...... segmentations. We obtain similar measures, as well as high Dice scores, compared to the experts. The run time for the proposed approach with a prototype implementation is around 3 minutes on a standard laptop, making the method suitable for rapid evaluation of orbital volume in UCS....

  2. Determination of air-loop volume and radon partition coefficient for measuring radon in water sample.

    Science.gov (United States)

    Lee, Kil Yong; Burnett, William C

    A simple method for the direct determination of the air-loop volume in a RAD7 system as well as the radon partition coefficient was developed allowing for an accurate measurement of the radon activity in any type of water. The air-loop volume may be measured directly using an external radon source and an empty bottle with a precisely measured volume. The partition coefficient and activity of radon in the water sample may then be determined via the RAD7 using the determined air-loop volume. Activity ratios instead of absolute activities were used to measure the air-loop volume and the radon partition coefficient. In order to verify this approach, we measured the radon partition coefficient in deionized water in the temperature range of 10-30 °C and compared the values to those calculated from the well-known Weigel equation. The results were within 5 % variance throughout the temperature range. We also applied the approach for measurement of the radon partition coefficient in synthetic saline water (0-75 ppt salinity) as well as tap water. The radon activity of the tap water sample was determined by this method as well as the standard RAD-H2O and BigBottle RAD-H2O. The results have shown good agreement between this method and the standard methods.

  3. Quantitative absorption cytometry for measuring red blood cell hemoglobin mass and volume.

    Science.gov (United States)

    Schonbrun, Ethan; Malka, Roy; Di Caprio, Giuseppe; Schaak, Diane; Higgins, John M

    2014-04-01

    We present an optical system, called the quantitative absorption cytometer (QAC), to measure the volume and hemoglobin mass of red blood cells flowing through a microfluidic channel. In contrast to clinical hematology analyzers, where cells are sphered in order for both volume and hemoglobin to be measured accurately, the QAC measures cells in their normal physiological shape. Human red blood cells are suspended in a refractive index-matching absorbing buffer, driven through a microfluidic channel, and imaged using a transmission light microscope onto a color camera. A red and a blue LED illuminate cells and images at each color are used to independently retrieve cell volume and hemoglobin mass. This system shows good agreement with red blood cell indices retrieved by a clinical hematology analyzer and in fact measures a smaller coefficient of variation of hemoglobin concentration. In addition to cell indices, the QAC returns height and mass maps of each measured cell. These quantitative images are valuable for analyzing the detailed morphology of individual cells as well as statistical outliers found in the data. We also measured red blood cells in hypertonic and hypotonic buffers to quantify the correlation between volume and hemoglobin mass under osmotic stress. Because this method is invariant to cell shape, even extremely nonspherical cells in hypertonic buffers can be measured accurately.

  4. Wireless Acoustic Measurement System

    Science.gov (United States)

    Anderson, Paul D.; Dorland, Wade D.; Jolly, Ronald L.

    2007-01-01

    A prototype wireless acoustic measurement system (WAMS) is one of two main subsystems of the Acoustic Prediction/ Measurement Tool, which comprises software, acoustic instrumentation, and electronic hardware combined to afford integrated capabilities for predicting and measuring noise emitted by rocket and jet engines. The other main subsystem is described in the article on page 8. The WAMS includes analog acoustic measurement instrumentation and analog and digital electronic circuitry combined with computer wireless local-area networking to enable (1) measurement of sound-pressure levels at multiple locations in the sound field of an engine under test and (2) recording and processing of the measurement data. At each field location, the measurements are taken by a portable unit, denoted a field station. There are ten field stations, each of which can take two channels of measurements. Each field station is equipped with two instrumentation microphones, a micro- ATX computer, a wireless network adapter, an environmental enclosure, a directional radio antenna, and a battery power supply. The environmental enclosure shields the computer from weather and from extreme acoustically induced vibrations. The power supply is based on a marine-service lead-acid storage battery that has enough capacity to support operation for as long as 10 hours. A desktop computer serves as a control server for the WAMS. The server is connected to a wireless router for communication with the field stations via a wireless local-area network that complies with wireless-network standard 802.11b of the Institute of Electrical and Electronics Engineers. The router and the wireless network adapters are controlled by use of Linux-compatible driver software. The server runs custom Linux software for synchronizing the recording of measurement data in the field stations. The software includes a module that provides an intuitive graphical user interface through which an operator at the control server

  5. Significance of left ventricular volume measurement after heart transplantation using radionuclide techniques

    Energy Technology Data Exchange (ETDEWEB)

    Novitzky, D.; Cooper, D.; Boniaszczuk, J.; Isaacs, S.; Fraser, R.C.; Commerford, P.J.; Uys, C.J.; Rose, A.G.; Smith, J.A.; Barnard, C.N.

    1985-02-01

    Multigated equilibrium blood pool scanning using Technetium 99m labeled red blood cells was used to measure left ventricular volumes in three heterotopic and one orthotopic heart transplant recipient(s). Simultaneously, an endomyocardial biopsy was performed and the degree of acute rejection was assessed by a histological scoring system. The scores were correlated to changes in ejection fraction and heart rate. Technetium 99m scanning data were pooled according to the endomyocardial biopsy score: no rejection; mild rejection; moderate rejection, and severe rejection. In each group, the median of the left ventricular volume parameters was calculated and correlated with the endomyocardial biopsy score, using a non-parametric one-way analysis of variance. A decrease in stroke volume correlated best with the endomyocardial biopsy score during acute rejection. A decrease in end-diastolic left ventricular volumes did not correlate as well. Changes in the end-systolic left ventricular volumes were not statistically significant, but using a simple correlation between end-systolic left ventricular volumes and endomyocardial biopsy the correlation reached significance. Changes in left ventricular volumes measured by Technetium 99m scanning may be useful to confirm the presence or absence of acute rejection in patients with heart grafts.

  6. The influence of urine volume on body impedance measurement.

    Science.gov (United States)

    Hong, K H; Park, K S

    2008-01-01

    Bio-signal has some characteristics that the signal is so weak. So, it is good that the factors to influence measured electrical signal are eliminated as much as they can. So, in this paper we will show the influence of urine in bladder on measuring human body impedance. Human urine has different conductivity from other human tissues. Therefore, if the volume of the urine changed, the measured body impedance data also changed.So, in this paper, we will show the influence of urine in bladder with foot-to-foot and thigh-to-thigh current paths. As a result, if the current flows through human bladder, the influence of urine in the bladder must be considered when the body impedance is measured

  7. Left Atrial Volume and Pulmonary Artery Diameter Are Noninvasive Measures of Age-Related Diastolic Dysfunction in Mice.

    Science.gov (United States)

    Medrano, Guillermo; Hermosillo-Rodriguez, Jesus; Pham, Thuy; Granillo, Alejandro; Hartley, Craig J; Reddy, Anilkumar; Osuna, Patricia Mejia; Entman, Mark L; Taffet, George E

    2016-09-01

    Impaired cardiac diastolic function occurs with aging in many species and may be difficult to measure noninvasively. In humans, left atrial (LA) volume is a robust measure of chronic diastolic function as the LA is exposed to increased left ventricular filling pressures. We hypothesized that LA volume would be a useful indicator of diastolic function in aging mice. Further, we asked whether pressures were propagated backwards affecting pulmonary arteries (PAs) and right ventricle (RV). We measured LA, PA, and RV infundibulum dimensions with echocardiography and used mouse-specific Doppler systems and pressure catheters for noninvasive and invasive measures. As C57BL/6 mice aged from 3 to 29-31 months, LA volume almost tripled. LA volume increases correlated with traditional diastolic function measures. Within groups of 14- and 31-month-old mice, LA volume correlated with diastolic function measured invasively. In serial studies, mice evaluated at 20 and 24 months showed monotonic increases in LA volume; other parameters changed less predictably. PA diameters, larger in 30-month-old mice than 6-month-old mice, correlated with LA volumes. Noninvasive LA volume and PA diameter assessments are useful and state independent measures of diastolic function in mice, correlating with other measures of diastolic dysfunction in aging. Furthermore, serial measurements over 4 months demonstrated consistent increases in LA volume suitable for longitudinal cardiac aging studies.

  8. A CO2 laser based two-volume collective scattering instrument for spatially localized turbulence measurements

    DEFF Research Database (Denmark)

    Saffman, Mark; Zoletnik, S.; Basse, Nils Plesner

    2001-01-01

    We describe and demonstrate a two-volume collective scattering system for localized measurements of plasma turbulence. The finite crossfield correlation length of plasma turbulence combined with spatial variations in the magnetic field direction are used to obtain spatially localized turbulence...

  9. Handbook of Systems Analysis: Volume 1. Overview. Chapter 2. The Genesis of Applied Systems Analysis

    OpenAIRE

    1981-01-01

    The International Institute for Applied Systems Analysis is preparing a Handbook of Systems Analysis, which will appear in three volumes: Volume 1: Overview is aimed at a widely varied audience of producers and users of systems analysis studies. Volume 2: Methods is aimed at systems analysts and other members of systems analysis teams who need basic knowledge of methods in which they are not expert; this volume contains introductory overviews of such methods. Volume 3: Cases co...

  10. Noninvasive Intracranial Volume and Pressure Measurements Using Ultrasound

    Science.gov (United States)

    Hargens, A. R.

    1998-01-01

    Prevention of secondary brain injuries following head can be accomplished most easily when intracranial pressure (ICP) is monitored. However, current measurement techniques are invasive and thus not practical in the combat environment. The Pulsed Phase Lock Loop (PPLL) devise, which was developed and patented, uses a unique, noninvasive ultrasonic phase comparison method to measure slight changes in cranial volume which occur with changes in ICP. Year one studies involved instrument improvements and measurement of altered intracranial distance with altered ICP in fresh cadavera. Our software was improved to facilitate future studies of normal subjects and trauma patients. Our bench studies proved that PPLL output correlated highly with changes in path length across a model cranium. Cadaveric studies demonstrated excellent compact, noninvasive devise for monitoring changes in intracranial distance may aid in the early detection of elevated ICP, decreasing risk of secondary brain injury and infection, and returning head-injured patients to duty.

  11. Measurements of the volume scattering function in a coastal environment

    Science.gov (United States)

    Berthon, Jean-François; Lee, Michael; Shybanov, Eugeny; Zibordi, Giuseppe

    2007-04-01

    The Volume Scattering Function (VSF) is an essential variable in the context of marine radiative transfer modeling and of the inversion of ocean colour remote sensing data. However, an important lack of knowledge on the VSF natural variability affects the present models, in particular for the coastal environment. Measurements of the Volume Scattering Function between 0.6° and 177.3° with an angular resolution of 0.3° were performed in the northern coastal Adriatic Sea onboard an oceanographic platform in October 2004 using a prototype instrument. Observed differences with the commonly used Petzold's functions are significant, in particular for the "open ocean" and "coastal" types in the backward directions. The use of an empirical relationship for the derivation of b b(λ) from a unique measurement of β(ψ,λ) at ψ=140 for the Hydroscat-6 was validated for this coastal site at that season. Finally, the use of the Kopelevich VSF model together with a measurement of b p(λ) at λ=555 nm allowed the reconstruction of the VSF to within about 35%.

  12. Integrated Optofluidic Chip for Low-Volume Fluid Viscosity Measurement

    Directory of Open Access Journals (Sweden)

    Tie Yang

    2017-02-01

    Full Text Available In the present work, an integrated optofluidic chip for fluid viscosity measurements in the range from 1 mPa·s to 100 mPa·s is proposed. The device allows the use of small sample volumes (<1 µL and the measurement of viscosity as a function of temperature. Thanks to the precise control of the force exerted on dielectric spheres by optical beams, the viscosity of fluids is assessed by comparing the experimentally observed movement of dielectric beads produced by the optical forces with that expected by numerical calculations. The chip and the developed technique are validated by analyzing several fluids, such as Milli-Q water, ethanol and water–glycerol mixtures. The results show a good agreement between the experimental values and those reported in the literature. The extremely reduced volume of the sample required and the high flexibility of this technique make it a good candidate for measuring a wide range of viscosity values as well as for the analysis of nonlinear viscosity in complex fluids.

  13. Effect of volume expansion on systemic hemodynamics and central and arterial blood volume in cirrhosis

    DEFF Research Database (Denmark)

    Møller, S; Bendtsen, F; Henriksen, Jens Henrik Sahl

    1995-01-01

    and in controls. METHODS: Thirty-nine patients with cirrhosis (12 patients with Child-Turcotte class A, 14 with class B, and 13 with class C) and 6 controls were studied. During hepatic vein catheterization, cardiac output, systemic vascular resistance, central and arterial blood volume, noncentral blood volume...

  14. Magnetic Resonance Venous Volume Measurements in Peripheral Artery Disease (from ELIMIT).

    Science.gov (United States)

    Kamran, Hassan; Nambi, Vijay; Negi, Smita; Yang, Eric Y; Chen, Changyi; Virani, Salim S; Kougias, Panos; Lumsden, Alan B; Morrisett, Joel D; Ballantyne, Christie M; Brunner, Gerd

    2016-11-01

    The relation between the arterial and venous systems in patients with impaired lower extremity blood flow remains poorly described. The objective of this secondary analysis of the Effectiveness of Intensive Lipid Modification Medication in Preventing the Progression on Peripheral Artery Disease Trial was to determine the association between femoral vein (FV) volumes and measurements of peripheral artery disease. FV wall, lumen, and total volumes were quantified with fast spin-echo proton density-weighted magnetic resonance imaging scans in 79 patients with peripheral artery disease over 2 years. Reproducibility was excellent for FV total vessel (intraclass correlation coefficient 0.924, confidence interval 0.910 to 0.935) and lumen volumes (intraclass correlation coefficient 0.893, confidence interval 0.873 to 0.910). Baseline superficial femoral artery volumes were directly associated with FV wall (r = 0.46, p <0.0001), lumen (r = 0.42, p = 0.0001), and total volumes (r = 0.46, p <0.0001). The 2-year change in maximum walking time was inversely associated with the 24-month change in FV total volume (r = -0.45, p = 0.03). In conclusion, FV volumes can be measured reliably with fast spin-echo proton density-weighted magnetic resonance imaging, and baseline superficial femoral artery plaque burden is positively associated with FV volumes, whereas the 2-year change in FV volumes and leg function show an inverse relation.

  15. Evaluation of right ventricular volumes measured by magnetic resonance imaging

    DEFF Research Database (Denmark)

    Møgelvang, J; Stubgaard, M; Thomsen, C

    1988-01-01

    Right ventricular volumes were determined in 12 patients with different levels of right and left ventricular function by magnetic resonance imaging (MRI) using an ECG gated multisection technique in planes perpendicular to the diastolic position of the interventricular septum. Right ventricular...... stroke volume was calculated as the difference between end-diastolic and end-systolic volume and compared to left ventricular stroke volume and to stroke volume determined simultaneously by a classical indicator dilution technique. There was good agreement between right ventricular stroke volume...... determined by MRI and by the indicator dilution method and between right and left ventricular stroke volume determined by MRI. Thus, MRI gives reliable values not only for left ventricular volumes, but also for right ventricular volumes. By MRI it is possible to obtain volumes from both ventricles...

  16. Thermal microstructure measurement system

    Science.gov (United States)

    Carver, Michael J. (Inventor)

    1985-01-01

    A thermal microstructure measurement system (TMMS) operates autonomously h its own internal power supply and telemeters data to a platform. A thermal array is mounted on a cross-braced frame designed to orient itself normal to existing currents with fixed sensor positioning bars protruding from the cross bars. A plurality of matched thermistors, conductivity probes and inclinometers are mounted on the frame. A compass and pressure transducer are contained in an electronics package suspended below the array. The array is deployed on a taut mooring below a subsurface float. Data are digitized, transmitted via cable to a surface buoy and then telemetered to the platform where the data is processed via a computer, recorded and/or displayed. The platform computer also sends commands to the array via telemetry.

  17. Speech Understanding Systems. Volume 5. Trip

    Science.gov (United States)

    1976-12-01

    modeling, parsing, pattern recognition, phonetic labeling, phonetic segmentation, phonological rules, phonology , pragmatic grammar, pragmatics...extraction, acoustic- phonetic analysis of the signal, phonological expansion of the lexicon, lexical matching and retrieval, syntactic analysis and...used by the assistant. Because acoustic, phonetic or phonological knowledge have been covered elsewhere (Volumes 1-3), we will be focusing on so-called

  18. SLSF loop handling system. Volume I. Structural analysis. [LMFBR

    Energy Technology Data Exchange (ETDEWEB)

    Ahmed, H.; Cowie, A.; Ma, D.

    1978-10-01

    SLSF loop handling system was analyzed for deadweight and postulated dynamic loading conditions, identified in Chapters II and III in Volume I of this report, using a linear elastic static equivalent method of stress analysis. Stress analysis of the loop handling machine is presented in Volume I of this report. Chapter VII in Volume I of this report is a contribution by EG and G Co., who performed the work under ANL supervision.

  19. A time-of-flight flow sensor for the volume measurement of trace amount of interstitial fluid

    Science.gov (United States)

    Yu, H.; Li, D.; Roberts, R. C.; Xu, K.; Tien, N. C.

    2012-05-01

    Transdermal extraction of interstitial fluid (ISF) offers an attractive method for noninvasive blood glucose monitoring. The existing macroscale systems are not suitable for ISF collection, mainly because of the minute volume of the transdermally extracted ISF which scatters on the skin surface. Human skin's low permeability to glucose and its varying permeability exemplify the crucial need to make precise ISF volume measurements in order to calculate blood glucose concentrations accurately. In this paper, we present a novel time-of-flight flow sensor consisting of four electrode pairs fabricated directly into the channel of a polydimethylsiloxane (PDMS) microfluidic device designed to accurately measure the volume of transdermally extracted ISF. As fluid traverses the channel, it bridges each electrode pair and changes its resistance. By measuring the time difference in resistance change between each electrode pair, a precise fluid volume can be measured. In order to verify the suitability of the sensor for biological applications, experiments were conducted using a normal saline solution which is similar to ISF. The stability of the sensor was tested using a fixed volume, and the coefficient of variation for 20 tests was determined to be 0.0041. The consistency of the sensor for varied volume measurements was shown by the high correlation coefficient (R2 = 0.9992) between the tested volume and the volume measured by a commercial micro syringe. The excellent functionality of the flow sensor can be extended toward the measurement of conductive chemical and biochemical buffers and reagents.

  20. Multibeam volume acoustic backscatter imagery and reverberation measurements in the northeastern Gulf of Mexico

    Science.gov (United States)

    Gallaudet, Timothy C.; deMoustier, Christian P.

    2002-08-01

    Multibeam volume acoustic backscatter imagery and reverberation measurements are derived from data collected in 200-m-deep waters in the northeastern Gulf of Mexico, with the Toroidal Volume Search Sonar (TVSS), a 68-kHz cylindrical sonar operated by the U.S. Navy's Coastal System Station. The TVSS's 360-degree vertical imaging plane allows simultaneous identification of multiple volume scattering sources and their discrimination from backscatter at the sea surface or the seafloor. This imaging capability is used to construct a three-dimensional representation of a pelagic fish school near the bottom. Scattering layers imaged in the mixed layer and upper thermocline are attributed to assemblages of epipelagic zooplankton. The fine scale patchiness of these scatterers is assessed with the two-dimensional variance spectra of vertical volume scattering strength images in the upper and middle water column. Mean volume reverberation levels exhibit a vertical directionality which is attributed to the volume scattering layers. Boundary echo sidelobe interference and reverberation is shown to be the major limitation in obtaining bioacoustic data with the TVSS. Because net tow and trawl samples were not collected with the acoustic data, the analysis presented is based upon comparison to previous biologic surveys in the northeastern Gulf of Mexico and reference to the bioacoustic literature. copyright 2002 Acoustical Society of America.

  1. Relation of the volume of the olfactory bulb to psychophysical measures of olfactory function.

    Science.gov (United States)

    Mazal, Patricia Portillo; Haehner, Antje; Hummel, Thomas

    2016-01-01

    The aim of this review is to investigate whether changes in olfactory bulb volume relate to changes in specific olfactory functions. We studied currently available peer-reviewed articles on the volume of the human olfactory bulb that also included a psychophysical measure of olfactory function. In the present review, we observed a very clear and consistent correlation between general olfactory function and olfactory bulb (OB) volume. We were not able to find a clear relationship between a specific smell component and OB volume, even when analyzing pathologic conditions separately. In some cases, changes were observed for different subtests, but these changes did not significantly correlate with OB volume or had only a borderline correlation. In other cases, we found contradictory data. Several factors may contribute to the difficulties in finding correlations with the different components of smell: (1) the OB volume may be influenced by information from olfactory receptor neurons (bottom-up effect), information from central nervous system (top-down effect) and by direct damage; (2) most pathologic conditions affect more than one area of the olfactory pathway; (3) small sample sizes of hyposmic subjects were used. We believe that it is necessary to do further studies with larger numbers of subjects to answer the currently investigated question.

  2. Formation of uniform fringe pattern free from diffraction noise at LDA measurement volume using holographic imaging configuration

    Science.gov (United States)

    Ghosh, Abhijit; Nirala, A. K.

    2016-05-01

    In the present study we have proposed a technique for improving fringe quality at laser Doppler anemometry measurement volume in real time using single hololens imaging configuration over conventional imaging configuration with Gaussian beam optics. In order to remove interference fringe gradients as well as higher order diffraction noise formed at measurement volume in the former approach, a combined hololens imaging system has also been proposed. For qualitative as well as quantitative analysis of fringes formed at measurement volume, atomic force microscopy (AFM) analysis has been performed.

  3. Research on Canal System Operation Based on Controlled Volume Method

    Directory of Open Access Journals (Sweden)

    Zhiliang Ding

    2009-10-01

    Full Text Available An operating simulation mode based on storage volume control method for multireach canal system in series was established. In allusion to the deficiency of existing controlled volume algorithm, the improved algorithm was proposed, that is the controlled volume algorithm of whole canal pools, the simulation results indicate that the storage volume and water level of each canal pool can be accurately controlled after the improved algorithm was adopted. However, for some typical discharge demand change operating conditions of canal, if the controlled volume algorithm of whole canal pool is still adopted, then it certainly will cause some unnecessary regulation, and consequently increases the disturbed canal reaches. Therefor, the idea of controlled volume operation method of continuous canal pools was proposed, and its algorithm was designed. Through simulation to practical project, the results indicate that the new controlled volume algorithm proposed for typical operating condition can comparatively obviously reduce the number of regulated check gates and disturbed canal pools for some typical discharge demand change operating conditions of canal, thus the control efficiency of canal system was improved. The controlled volume method of operation is specially suitable for large-scale water delivery canal system which possesses complex operation requirements.

  4. Two-Nucleon Systems in a Finite Volume

    Energy Technology Data Exchange (ETDEWEB)

    Briceno, Raul

    2014-11-01

    I present the formalism and methodology for determining the nucleon-nucleon scattering parameters from the finite volume spectra obtained from lattice quantum chromodynamics calculations. Using the recently derived energy quantization conditions and the experimentally determined scattering parameters, the bound state spectra for finite volume systems with overlap with the 3S1-3D3 channel are predicted for a range of volumes. It is shown that the extractions of the infinite-volume deuteron binding energy and the low-energy scattering parameters, including the S-D mixing angle, are possible from Lattice QCD calculations of two-nucleon systems with boosts of |P| <= 2pi sqrt{3}/L in volumes with spatial extents L satisfying fm <~ L <~ 14 fm.

  5. Dedicated breast CT: Fibroglandular volume measurements in a diagnostic population

    Energy Technology Data Exchange (ETDEWEB)

    Vedantham, Srinivasan; Shi Linxi; Karellas, Andrew; O' Connell, Avice M. [Department of Radiology, University of Massachusetts Medical School, Worcester, Massachusetts 01655 (United States); Department of Imaging Sciences, University of Rochester Medical Center, Rochester, New York 14642 (United States)

    2012-12-15

    Purpose: To determine the mean and range of volumetric glandular fraction (VGF) of the breast in a diagnostic population using a high-resolution flat-panel cone-beam dedicated breast CT system. This information is important for Monte Carlo-based estimation of normalized glandular dose coefficients and for investigating the dependence of VGF on breast dimensions, race, and pathology. Methods: Image data from a clinical trial investigating the role of dedicated breast CT that enrolled 150 women were retrospectively analyzed to determine the VGF. The study was conducted in adherence to a protocol approved by the institutional human subjects review boards and written informed consent was obtained from all study participants. All participants in the study were assigned BI-RADS{sup Registered-Sign} 4 or 5 as per the American College of Radiology assessment categories after standard diagnostic work-up and underwent dedicated breast CT exam prior to biopsy. A Gaussian-kernel based fuzzy c-means algorithm was used to partition the breast CT images into adipose and fibroglandular tissue after segmenting the skin. Upon determination of the accuracy of the algorithm with a phantom, it was applied to 137 breast CT volumes from 136 women. VGF was determined for each breast and the mean and range were determined. Pathology results with classification as benign, malignant, and hyperplasia were available for 132 women, and were used to investigate if the distributions of VGF varied with pathology. Results: The algorithm was accurate to within {+-}1.9% in determining the volume of an irregular shaped phantom. The study mean ({+-} inter-breast SD) for the VGF was 0.172 {+-} 0.142 (range: 0.012-0.719). VGF was found to be negatively correlated with age, breast dimensions (chest-wall to nipple length, pectoralis to nipple length, and effective diameter at chest-wall), and total breast volume, and positively correlated with fibroglandular volume. Based on pathology, pairwise statistical

  6. Finite volume evolution Galerkin (FVEG) methods for hyperbolic systems

    OpenAIRE

    Lukácová-Medvid'ová, Maria; Morton, K.W.; Warnecke, Gerald

    2003-01-01

    The subject of the paper is the derivation and analysis of new multidimensional, high-resolution, finite volume evolution Galerkin (FVEG) schemes for systems of nonlinear hyperbolic conservation laws. Our approach couples a finite volume formulation with approximate evolution operators. The latter are constructed using the bicharacteristics of the multidimensional hyperbolic system, such that all of the infinitely many directions of wave propagation are taken into account. In particular, we p...

  7. Computer Sciences and Data Systems, volume 1

    Science.gov (United States)

    1987-01-01

    Topics addressed include: software engineering; university grants; institutes; concurrent processing; sparse distributed memory; distributed operating systems; intelligent data management processes; expert system for image analysis; fault tolerant software; and architecture research.

  8. Multiple IMU system development, volume 1

    Science.gov (United States)

    Landey, M.; Mckern, R.

    1974-01-01

    A redundant gimballed inertial system is described. System requirements and mechanization methods are defined and hardware and software development is described. Failure detection and isolation algorithms are presented and technology achievements described. Application of the system as a test tool for shuttle avionics concepts is outlined.

  9. DIAGNOdent measurements and correlation with the depth and volume of minimally invasive cavity preparations.

    Science.gov (United States)

    Hamilton, James C; Gregory, William A; Valentine, John B

    2006-01-01

    In this clinical study, DIAGNOdent (KaVo) was used to assess previously diagnosed carious lesions in the pits and fissures of first and second molars. The measurements from this device were correlated with the depth and volume of the cavity preparations that resulted from minimal intervention to remove occlusal carious lesions. Twenty-five patients, 18 years of age and older, who were previously scheduled for an occlusal restoration due to caries, were recruited and enrolled in this clinical study. These patients had 48 qualifying teeth without previous restorations, sealants or other carious lesions. The occlusal surface of each study tooth was cleaned utilizing ProphyFlex2 (KaVo). Two dentists separately traced the pit and fissure system of each tooth using DIAGNOdent for two 15-second periods each. The peak reading of each of the four measurements was recorded. An impression of the occlusal surface of each tooth was recorded with a polyvinyl siloxane bite registration material. The carious lesions were removed with an air abrasion unit employing a 0.015-inch nozzle opening utilizing minimal operative intervention. A low viscosity polyvinyl siloxane was used to take an impression of the cavity preparation impression, using the bite registration impression to form the occlusal surface of the preparation impression. The preparation impression volume was calculated from its weight, using the known density of the impression material. The greatest depth of the preparation was measured. The Pearson correlation coefficient was used to investigate any relationship between depth or volume of the preparation impression and the DIAGNOdent measurements. The correlation for preparation volume and maximum DIAGNOdent measurement was 0.191 (p = 0.189). Other logical subsets of cases also did not result in any statistically significant correlations between the DIAGNOdent readings and the depth or volume of the final cavity preparations.

  10. Volume measurement of the leg with the depth camera for quantitative evaluation of edema

    Science.gov (United States)

    Kiyomitsu, Kaoru; Kakinuma, Akihiro; Takahashi, Hiroshi; Kamijo, Naohiro; Ogawa, Keiko; Tsumura, Norimichi

    2017-02-01

    Volume measurement of the leg is important in the evaluation of leg edema. Recently, method for measurement by using a depth camera is proposed. However, many depth cameras are expensive. Therefore, we propose a method using Microsoft Kinect. We obtain a point cloud of the leg by Kinect Fusion technique and calculate the volume. We measured the volume of leg for three healthy students during three days. In each measurement, the increase of volume was confirmed from morning to evening. It is known that the volume of leg is increased in doing office work. Our experimental results meet this expectation.

  11. The analysis of deviations on measured volumes between OSBRA pipeline tank farms and its customers

    Energy Technology Data Exchange (ETDEWEB)

    Kotchetkoff Neto, Andre Paulo; Kawamoto, Fabio Yoshikazu [Petrobas Transporte S.A. - Transpetro, (Brazil)

    2010-07-01

    The Sao Paulo - Brasilia pipeline (OSBRA) is a very long multi product pipeline in Brazil. It has a network of several tank farms, pump stations and truck loadings to deliver oil, gas and LPG to customers. The volume of these fuels is usually measured before delivery at two measure points. This paper reports the use of statistical tools to analyze the measurement data. The purpose was to understand the computed differences between the OSBRA tank farm installations and the customer tank farm installations. The use of statistical tools brought new insights, such as the existence of systematic error or the variability of each individual system. These tools were also used to verify the accuracy of operational measurement devices. An analysis based on in-field data was carried out between two OSBRA tank farms. This paper showed that the use of statistical tools, rather than fixed limits, can provide more precise information about measurement systems behaviors.

  12. Living Expert System (LEXSYS). Volume 6

    Science.gov (United States)

    1989-05-15

    PROTOLEX SUBNET DISCUSSIONS: Attack Helicopter Operations; Low Intensity Conflict; Continuous Operations. Keywords: Dialogue; Discussions; Military commanders; Decision making; Decision aids; LEXSYS (Living Expert System ).

  13. Accurate mass replacement method for the sediment concentration measurement with a constant volume container

    Science.gov (United States)

    Ban, Yunyun; Chen, Tianqin; Yan, Jun; Lei, Tingwu

    2017-04-01

    The measurement of sediment concentration in water is of great importance in soil erosion research and soil and water loss monitoring systems. The traditional weighing method has long been the foundation of all the other measuring methods and instrument calibration. The development of a new method to replace the traditional oven-drying method is of interest in research and practice for the quick and efficient measurement of sediment concentration, especially field measurements. A new method is advanced in this study for accurately measuring the sediment concentration based on the accurate measurement of the mass of the sediment-water mixture in the confined constant volume container (CVC). A sediment-laden water sample is put into the CVC to determine its mass before the CVC is filled with water and weighed again for the total mass of the water and sediments in the container. The known volume of the CVC, the mass of sediment-laden water, and sediment particle density are used to calculate the mass of water, which is replaced by sediments, therefore sediment concentration of the sample is calculated. The influence of water temperature was corrected by measuring water density to determine the temperature of water before measurements were conducted. The CVC was used to eliminate the surface tension effect so as to obtain the accurate volume of water and sediment mixture. Experimental results showed that the method was capable of measuring the sediment concentration from 0.5 up to 1200 kg m‑3. A good liner relationship existed between the designed and measured sediment concentrations with all the coefficients of determination greater than 0.999 and the averaged relative error less than 0.2%. All of these seem to indicate that the new method is capable of measuring a full range of sediment concentration above 0.5 kg m‑3 to replace the traditional oven-drying method as a standard method for evaluating and calibrating other methods.

  14. Effect of electrode location on bladder volume measurement in bioimpedance system%生物电阻抗系统的电极位置对膀胱尿量测量的影响

    Institute of Scientific and Technical Information of China (English)

    王倩; 陈世雄; 许欢; 周广敏; 刘官正; 蒋庆

    2014-01-01

    研究生物电阻抗测量系统中电极位置对膀胱尿量信号特征的影响,提高检测过程中信号的敏感度,以帮助尿潴留患者定时排尿。方法健康男性大学生8名,采用双路开关同时采集两路电极位置的信号,分别观察电极在小腹部不同位置及测量电极和刺激电极的相对距离对阻抗变化值ΔZ和阻抗变化率ΔZ/Z的影响。结果在使用生物电阻抗技术测量膀胱积尿过程中,生物电阻抗 Z呈现变小的趋势,不同的刺激/测量电极位置对应的阻抗变化值ΔZ和变化率ΔZ/Z不同。结论肚脐下10 cm,正负两个测量电极距肚脐中线均为3 cm的位置,正负两个刺激电极与对应正负两个测量电极间距离均为5 cm的位置为最佳的测量位置,其阻抗变化值ΔZ 达(1.2±0.6)Ω,变化率ΔZ/Z 达8.2%±4.9%。该位置的确定对使用生物电阻抗技术提醒尿潴留患者在恰当的时间排空膀胱具有重要的临床意义。%This paper investigates the effect of electrode position on bladder volume measurement with bioimpedance system which is helpful for the patients with urine retention to micturate. Methods The variation of bioimpedance ΔZ and gradient of bioimpedance ΔZ/Z in eight healthy male students are observed in bladder filling,when the stimulating or measuring electrodes are fixed different positions in abdomen by using a two-way switch.Results During the measurement of bladder filling,there is a decrease trend for bioimpedance Z.The variation and gradient of bioimpedance are different with the different electrode positions.Conclusions The optimal location is:1 0 cm under navel,the measuring electrodes both are 3 cm to navel’s midcourt line,and the distance between stimulating and measuring electrodes both are 5 cm.In this electrode location,the variation (ΔZ ) of bioimpedance is up to (1.2 ±0.6 ) ohm,and the gradient of bioimpedance (ΔZ/Z ) is up to 8.2% ±4.9%.The location is

  15. Measurement and correlation of excess molar volumes for mixtures of 1-propanol and aromatic hydrocarbons

    Energy Technology Data Exchange (ETDEWEB)

    Gahlyan, Suman; Rani, Manju; Maken, Sanjeev Kumar [Deenbandhu Chhotu Ram University of Science and Technology, Murthal (India); Lee, Inkyu; Moon, Il [Yonsei University, Seoul (Korea, Republic of)

    2015-01-15

    Excess molar volumes (V{sub m}{sup E} ) have been measured at 303.15 K for 1-propanol+benzene or toluene or o- or m- or p-xylene mixtures using V-shape dilatometer. The V{sub m}{sup E} values, for an equimolar composition, vary in the order: benzene>toluene-m-xylene>o-xylene>p-xylene. The V{sub m}{sup E} data have been used to calculate partial molar volumes, excess partial molar volumes, and apparent molar volumes of 1-propanol and aromatic hydrocarbons over the entire range of composition. The excess volume data have also been interpreted in terms of graph-theoretical approach and Prigogine-Flory-Patterson theory (PFP). While PFP theory fails to predict the V{sub m}{sup E} values for systems with s-shaped V{sub m}{sup E} versus x{sub 1} graph, the V{sub m}{sup E} values calculated by graph theory compare reasonably well with the corresponding experimental values. This graph theory analysis has further yielded information about the state of aggregation of pure components as well as of the mixtures.

  16. Lung Volume Measured during Sequential Swallowing in Healthy Young Adults

    Science.gov (United States)

    Hegland, Karen Wheeler; Huber, Jessica E.; Pitts, Teresa; Davenport, Paul W.; Sapienza, Christine M.

    2011-01-01

    Purpose: Outcomes from studying the coordinative relationship between respiratory and swallow subsystems are inconsistent for sequential swallows, and the lung volume at the initiation of sequential swallowing remains undefined. The first goal of this study was to quantify the lung volume at initiation of sequential swallowing ingestion cycles and…

  17. Urban Run-off Volumes Dependency on Rainfall Measurement Method

    DEFF Research Database (Denmark)

    Pedersen, L.; Jensen, N. E.; Rasmussen, Michael R.;

    2005-01-01

    Urban run-off is characterized with fast response since the large surface run-off in the catchments responds immediately to variations in the rainfall. Modeling such type of catchments is most often done with the input from very few rain gauges, but the large variation in rainfall over small area...... resolutions and single gauge rainfall was fed to a MOUSE run-off model. The flow and total volume over the event is evaluated.......Urban run-off is characterized with fast response since the large surface run-off in the catchments responds immediately to variations in the rainfall. Modeling such type of catchments is most often done with the input from very few rain gauges, but the large variation in rainfall over small areas...... suggests that rainfall needs to be measured with a much higher spatial resolution (Jensen and Pedersen, 2004). This paper evaluates the impact of using high-resolution rainfall information from weather radar compared to the conventional single gauge approach. The radar rainfall in three different...

  18. Systems Measures of Water Distribution System Resilience

    Energy Technology Data Exchange (ETDEWEB)

    Klise, Katherine A. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Murray, Regan [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Walker, La Tonya Nicole [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2015-01-01

    Resilience is a concept that is being used increasingly to refer to the capacity of infrastructure systems to be prepared for and able to respond effectively and rapidly to hazardous events. In Section 2 of this report, drinking water hazards, resilience literature, and available resilience tools are presented. Broader definitions, attributes and methods for measuring resilience are presented in Section 3. In Section 4, quantitative systems performance measures for water distribution systems are presented. Finally, in Section 5, the performance measures and their relevance to measuring the resilience of water systems to hazards is discussed along with needed improvements to water distribution system modeling tools.

  19. Radial Internal Material Handling System (RIMS) for Circular Habitat Volumes

    Science.gov (United States)

    Howe, Alan S.; Haselschwardt, Sally; Bogatko, Alex; Humphrey, Brian; Patel, Amit

    2013-01-01

    On planetary surfaces, pressurized human habitable volumes will require a means to carry equipment around within the volume of the habitat, regardless of the partial gravity (Earth, Moon, Mars, etc.). On the NASA Habitat Demonstration Unit (HDU), a vertical cylindrical volume, it was determined that a variety of heavy items would need to be carried back and forth from deployed locations to the General Maintenance Work Station (GMWS) when in need of repair, and other equipment may need to be carried inside for repairs, such as rover parts and other external equipment. The vertical cylindrical volume of the HDU lent itself to a circular overhead track and hoist system that allows lifting of heavy objects from anywhere in the habitat to any other point in the habitat interior. In addition, the system is able to hand-off lifted items to other material handling systems through the side hatches, such as through an airlock. The overhead system consists of two concentric circle tracks that have a movable beam between them. The beam has a hoist carriage that can move back and forth on the beam. Therefore, the entire system acts like a bridge crane curved around to meet itself in a circle. The novelty of the system is in its configuration, and how it interfaces with the volume of the HDU habitat. Similar to how a bridge crane allows coverage for an entire rectangular volume, the RIMS system covers a circular volume. The RIMS system is the first generation of what may be applied to future planetary surface vertical cylinder habitats on the Moon or on Mars.

  20. Digital Systems Validation Handbook. Volume 2

    Science.gov (United States)

    1989-02-01

    Horizontal Situation Indicator HSRB (6) High-Speed Ring Bus HVDC (15) High Voltage dc Hz (3,15) Hertz I/O (5,10,15) Input/Output I (13) Current I-dot (13... HVDC VS CONVENTIONAL POWER 15-78 15-vi 0 1.0 Electromechanical Actuation Systems Technology I Introduction and Scope This chapter covers the...system. Size, weight, and maintainability were all improved over the conventional system. A trade study conducted to compare the High Voltage dc ( HVDC

  1. Measurement System and Calibration report

    DEFF Research Database (Denmark)

    Kock, Carsten Weber; Vesth, Allan

    This Measurement System & Calibration report is describing DTU’s measurement system installed at a specific wind turbine. A major part of the sensors has been installed by others (see [1]) the rest of the sensors have been installed by DTU. The results of the measurements, described in this report...

  2. Measurement System and Calibration report

    DEFF Research Database (Denmark)

    Gómez Arranz, Paula; Villanueva, Héctor

    This Measurement System & Calibration report is describing DTU’s measurement system installed at a specific wind turbine. A major part of the sensors has been installed by others (see [1]) the rest of the sensors have been installed by DTU. The results of the measurements, described in this repor...

  3. Fluid Vessel Quantity Using Non-invasive PZT Technology Flight Volume Measurements Under Zero G Analysis

    Science.gov (United States)

    Garofalo, Anthony A

    2013-01-01

    The purpose of the project is to perform analysis of data using the Systems Engineering Educational Discovery (SEED) program data from 2011 and 2012 Fluid Vessel Quantity using Non-Invasive PZT Technology flight volume measurements under Zero G conditions (parabolic Plane flight data). Also experimental planning and lab work for future sub-orbital experiments to use the NASA PZT technology for fluid volume measurement. Along with conducting data analysis of flight data, I also did a variety of other tasks. I provided the lab with detailed technical drawings, experimented with 3d printers, made changes to the liquid nitrogen skid schematics, and learned how to weld. I also programmed microcontrollers to interact with various sensors and helped with other things going on around the lab.

  4. Fluid Vessel Quantity using Non-Invasive PZT Technology Flight Volume Measurements Under Zero G Analysis

    Science.gov (United States)

    Garofalo, Anthony A.

    2013-01-01

    The purpose of the project is to perform analysis of data using the Systems Engineering Educational Discovery (SEED) program data from 2011 and 2012 Fluid Vessel Quantity using Non-Invasive PZT Technology flight volume measurements under Zero G conditions (parabolic Plane flight data). Also experimental planning and lab work for future sub-orbital experiments to use the NASA PZT technology for fluid volume measurement. Along with conducting data analysis of flight data, I also did a variety of other tasks. I provided the lab with detailed technical drawings, experimented with 3d printers, made changes to the liquid nitrogen skid schematics, and learned how to weld. I also programmed microcontrollers to interact with various sensors and helped with other things going on around the lab.

  5. Measurement Systems Advisory Group

    Science.gov (United States)

    1974-04-01

    noted with the aluminum wire used in the lacing. For these reasons the tests were concluded and deemed unsatisfactory. The second system tested was an...vehicle for "bringing many particulate pollutants into contact with the tape or magnetic heads, e.g., from deodorant spray powders, face powder and

  6. Measuring name system health

    NARCIS (Netherlands)

    Casalicchio, Emiliano; Caselli, M.; Coletta, Alessio; Di Blasi, Salvatore; Fovino, Igor Nai; Butts, Jonathan; Shenoi, Sujeet

    2012-01-01

    Modern critical infrastructure assets are exposed to security threats arising from their use of IP networks and the Domain Name System (DNS). This paper focuses on the health of DNS. Indeed, due to the increased reliance on the Internet, the degradation of DNS could have significant consequences for

  7. Measuring name system health

    NARCIS (Netherlands)

    Casalicchio, Emiliano; Caselli, Marco; Coletta, Alessio; Di Blasi, Salvatore; Fovino, Igor Nai; Butts, Jonathan; Shenoi, Sujeet

    2012-01-01

    Modern critical infrastructure assets are exposed to security threats arising from their use of IP networks and the Domain Name System (DNS). This paper focuses on the health of DNS. Indeed, due to the increased reliance on the Internet, the degradation of DNS could have significant consequences for

  8. OMERACT Rheumatoid Arthritis Magnetic Resonance Imaging Studies. Exercise 5: an international multicenter reliability study using computerized MRI erosion volume measurements

    DEFF Research Database (Denmark)

    Bird, P; Ejbjerg, B; McQueen, F;

    2003-01-01

    with metacarpophalangeal (MCP) joints 2 to 5 of the dominant hand included in the field of view. Three readers were instructed to grade MCP 2 and 3 using the OMERACT grading system and then to measure the erosion volume of the same joints using OSIRIS software. The inter-reader reliability of the grading method....... Good correlation was demonstrated between the total erosion scores and the total erosion volumes. For both erosion volumes and erosion scores, 1 mm and 3 mm acquisitions produced variable results between readers, with no clear pattern of underestimation or overestimation for either slice thickness....... The volume estimation method was more time consuming, taking roughly 5 times as long as the scoring method. Computerized MRI erosion volume measurements are feasible, with high intra-observer and inter-occasion reliabilities. Despite high ICC, the inter-observer reliability is not sufficient for multicenter...

  9. Integrated safety management system verification: Volume 2

    Energy Technology Data Exchange (ETDEWEB)

    Christensen, R.F.

    1998-08-10

    Department of Energy (DOE) Policy (P) 450.4, Safety Management System Policy, commits to institutionalization of an Integrated Safety Management System (ISMS) throughout the DOE complex. The DOE Acquisition Regulations (DEAR, 48 CFR 970) requires contractors to manage and perform work in accordance with a documented Integrated Safety Management System (ISMS). Guidance and expectations have been provided to PNNL by incorporation into the operating contract (Contract DE-ACM-76FL0 1830) and by letter. The contract requires that the contractor submit a description of their ISMS for approval by DOE. PNNL submitted their proposed Safety Management System Description for approval on November 25,1997. RL tentatively approved acceptance of the description pursuant to a favorable recommendation from this review. The Integrated Safety Management System Verification is a review of the adequacy of the ISMS description in fulfilling the requirements of the DEAR and the DOE Policy. The purpose of this review is to provide the Richland Operations Office Manager with a recommendation for approval of the ISMS description of the Pacific Northwest Laboratory based upon compliance with the requirements of 49 CFR 970.5204(-2 and -78); and to verify the extent and maturity of ISMS implementation within the Laboratory. Further the review will provide a model for other DOE laboratories managed by the Office of Assistant Secretary for Energy Research.

  10. A Review of the Definition and Measurement of Poverty: Volume I, Summary Review Paper; Volume II, Annotated Bibliography. The Measure of Poverty, Technical Paper III.

    Science.gov (United States)

    Oster, Sharon; And Others

    This study reviews the existing literature on a series of issues associated with the defintion and measurement of poverty, and it consists of a summary report covering this research (Volume I), and an annotated bibliography (Volume II). Eleven specific issues were identified and reviewed in this study: (1) the historical definitions of poverty,…

  11. Transportation systems analyses: Volume 1: Executive Summary

    Science.gov (United States)

    1993-05-01

    The principal objective of this study is to accomplish a systems engineering assessment of the nation's space transportation infrastructure. This analysis addresses the necessary elements to perform man delivery and return, cargo transfer, cargo delivery, payload servicing, and the exploration of the Moon and Mars. Specific elements analyzed, but not limited to, include the Space Exploration Initiative (SEI), the National Launch System (NLS), the current expendable launch vehicle (ELV) fleet, ground facilities, the Space Station Freedom (SSF), and other civil, military and commercial payloads. The performance of this study entails maintaining a broad perspective on the large number of transportation elements that could potentially comprise the U.S. space infrastructure over the next several decades. To perform this systems evaluation, top-level trade studies are conducted to enhance our understanding of the relationships between elements of the infrastructure. This broad 'infrastructure-level perspective' permits the identification of preferred infrastructures. Sensitivity analyses are performed to assure the credibility and usefulness of study results. This executive summary of the transportation systems analyses (TSM) semi-annual report addresses the SSF logistics resupply. Our analysis parallels the ongoing NASA SSF redesign effort. Therefore, there could be no SSF design to drive our logistics analysis. Consequently, the analysis attempted to bound the reasonable SSF design possibilities (and the subsequent transportation implications). No other strategy really exists until after a final decision is rendered on the SSF configuration.

  12. Eddy Correlation Flux Measurement System

    Data.gov (United States)

    Oak Ridge National Laboratory — The eddy correlation (ECOR) flux measurement system provides in situ, half-hour measurements of the surface turbulent fluxes of momentum, sensible heat, latent heat,...

  13. 30 CFR 250.1163 - How must I measure gas flaring or venting volumes and liquid hydrocarbon burning volumes, and...

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 2 2010-07-01 2010-07-01 false How must I measure gas flaring or venting... SULPHUR OPERATIONS IN THE OUTER CONTINENTAL SHELF Oil and Gas Production Requirements Flaring, Venting, and Burning Hydrocarbons § 250.1163 How must I measure gas flaring or venting volumes and liquid...

  14. Integrated safety management system verification: Volume 1

    Energy Technology Data Exchange (ETDEWEB)

    Christensen, R.F.

    1998-08-12

    Department of Energy (DOE) Policy (P) 450.4, Safety Management System Policy, commits to institutionalizing an Integrated Safety Management System (ISMS) throughout the DOE complex. The DOE Acquisition Regulations (DEAR 48 CFR 970) requires contractors to manage and perform work in accordance with a documented Integrated Safety Management System. The Manager, Richland Operations Office (RL), initiated a combined Phase 1 and Phase 2 Integrated Safety Management Verification review to confirm that PNNL had successfully submitted a description of their ISMS and had implemented ISMS within the laboratory facilities and processes. A combined review was directed by the Manager, RL, based upon the progress PNNL had made in the implementation of ISM. This report documents the results of the review conducted to verify: (1) that the PNNL integrated safety management system description and enabling documents and processes conform to the guidance provided by the Manager, RL; (2) that corporate policy is implemented by line managers; (3) that PNNL has provided tailored direction to the facility management; and (4) the Manager, RL, has documented processes that integrate their safety activities and oversight with those of PNNL. The general conduct of the review was consistent with the direction provided by the Under Secretary`s Draft Safety Management System Review and Approval Protocol. The purpose of this review was to provide the Manager, RL, with a recommendation to the adequacy of the ISMS description of the Pacific Northwest Laboratory based upon compliance with the requirements of 49 CFR 970.5204(-2 and -78); and, to provide an evaluation of the extent and maturity of ISMS implementation within the Laboratory. Further, this review was intended to provide a model for other DOE Laboratories. In an effort to reduce the time and travel costs associated with ISM verification the team agreed to conduct preliminary training and orientation electronically and by phone. These

  15. Integrated safety management system verification: Volume 1

    Energy Technology Data Exchange (ETDEWEB)

    Christensen, R.F.

    1998-08-12

    Department of Energy (DOE) Policy (P) 450.4, Safety Management System Policy, commits to institutionalizing an Integrated Safety Management System (ISMS) throughout the DOE complex. The DOE Acquisition Regulations (DEAR 48 CFR 970) requires contractors to manage and perform work in accordance with a documented Integrated Safety Management System. The Manager, Richland Operations Office (RL), initiated a combined Phase 1 and Phase 2 Integrated Safety Management Verification review to confirm that PNNL had successfully submitted a description of their ISMS and had implemented ISMS within the laboratory facilities and processes. A combined review was directed by the Manager, RL, based upon the progress PNNL had made in the implementation of ISM. This report documents the results of the review conducted to verify: (1) that the PNNL integrated safety management system description and enabling documents and processes conform to the guidance provided by the Manager, RL; (2) that corporate policy is implemented by line managers; (3) that PNNL has provided tailored direction to the facility management; and (4) the Manager, RL, has documented processes that integrate their safety activities and oversight with those of PNNL. The general conduct of the review was consistent with the direction provided by the Under Secretary`s Draft Safety Management System Review and Approval Protocol. The purpose of this review was to provide the Manager, RL, with a recommendation to the adequacy of the ISMS description of the Pacific Northwest Laboratory based upon compliance with the requirements of 49 CFR 970.5204(-2 and -78); and, to provide an evaluation of the extent and maturity of ISMS implementation within the Laboratory. Further, this review was intended to provide a model for other DOE Laboratories. In an effort to reduce the time and travel costs associated with ISM verification the team agreed to conduct preliminary training and orientation electronically and by phone. These

  16. Living Expert System (LEXSYS). Volume 7

    Science.gov (United States)

    1989-05-15

    Partial contents: Army: LEXSYS--What Its All About; Summary of Team Meeting; How Can We Build a Non-Maintenance Intensive Expert Data Base; Cost Data for LEXSYS Prototype Issues; Search for the Perfect Rolodex; Reaching Decision Points in LEXSYS Subnets; An Architecture for a Prototype Net?; Helicopter FLOT Operations; Battlestaff Integration; Hardware Availability. Keywords: Dialogue; Conversation; LEXSYS (Living Expert System ); Decision making; Decision aids.

  17. Omega Navigation System Course Book. Volume 2

    Science.gov (United States)

    1994-07-01

    GPS) - 0846 6. PCD ASSIGNMENT: None G.2.3 Hawaii 1. LETTER DESIGNATION: "C" 2. LQCATION: a. Geographic: Haiku Valley, Oahu Island, Hawaii, U.S.A. b...systems, 2-25, 12-27 inductively matching, 3-23 Haiku , 2-3, 2-11 2inertial navigation, 4-39HYDROLANT, 2-29 hard-copy coverage diagrams, 2-33 inertial

  18. 21 CFR 862.1130 - Blood volume test system.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Blood volume test system. 862.1130 Section 862.1130 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES CLINICAL CHEMISTRY AND CLINICAL TOXICOLOGY DEVICES Clinical Chemistry Test Systems §...

  19. Omega Navigation System Course Book. Volume 1.

    Science.gov (United States)

    1994-07-01

    antenna must be about 15 percent taller . Figure 3.4-9 is a photograph of a grounded tower antenna systemn at the La Reuinion iransmittingy station. .3...provides the 0-30613 10-2-92 F Indicatec1 Inertial Craft Position + Navigation " Cora ected System Craft Position Position Indicated + Position Error...o0 o0 la Na % ;6 0i0~~oCOC~ H NNa oil r- corA t Cl~𔃺 A0A 9 co HQL (n oHI- HHH~~~~~~~~~~f ClllNMNllll~Nlll(JCi~llA CliC to w N0000000a000& 0’c", 100

  20. Compendium of Practical Astronomy. Volume 2: Earth and Solar System.

    Science.gov (United States)

    Augensen, H. J.; Heintz, W. D.; Roth, Günter D.

    The Compendium of Practical Astronomy is a revised and enlarged English version of the fourth edition of G. Roth's handbook for stargazers. In three volumes 28 carefully edited articles aimed especially at amateur astronomers and students and teachers of astronomy in high schools and colleges cover the length and breadth of practical astronomy. Volume 1 contains information on modern instrumentation and reduction techniques, including spherical astronomy, error estimations, telescope mountings, astrophotography, and more. Volume 2 covers the planetary system, with contributions on artificial satellites, comets, the polar aurorae, and the effects of the atmosphere on observational data. Volume 3 is devoted to stellar objects, variable stars and binary stars in particular. An introduction to the astronomical literature and a comprehensive chapter on astronomy education and instructional aids make the Compedium a useful complement to any college library.

  1. Compendium of Practical Astronomy. Volume 3: Stars and Stellar Systems.

    Science.gov (United States)

    Augensen, H. J.; Heintz, W. D.; Roth, Günter D.

    The Compendium of Practical Astronomy is a revised and enlarged English version of the fourth edition of G. Roth's famous handbook for stargazers. In three volumes 28 carefully edited articles aimed especially at amateur astronomers and students and teachers of astronomy in high schools and colleges cover the length and breadth of practical astronomy. Volume 1 contains information on modern instrumentation and reduction techniques, including spherical astronomy, error estimations, telescope mountings, astrophotography, and more. Volume 2 covers the planetary system, with contributions on artificial satellites, comets, the polar aurorae, and the effects of the atmophere on observational data. Volume 3 is devoted to stellar objects, variable stars and binary stars in particular, the Milky Way and Galaxies. An introduction to the astronomical literature and a comprehensive chapter on astronomy education and instructional aids make the Compendium a useful complement to any college library.

  2. A transient method for measuring the gas volume fraction in a mixed gas-liquid flow using acoustic resonance spectroscopy

    Institute of Scientific and Technical Information of China (English)

    2010-01-01

    In this paper, the feasibility of measuring the gas volume fraction in a mixed gas-liquid flow by using an acoustic resonant spectroscopy (ARS) method in a transient way is studied theoretically and experimentally. Firstly, the effects of sizes and locations of a single air bubble in a cylindrical cavity with two open ends on resonant frequencies are investigated numerically. Then, a transient measurement system for ARS is established, and the trends of the resonant frequencies (RFs) and resonant amplitudes (RAs) in the cylindrical cavity with gas flux inside are investigated experimentally. The measurement results by the proposed transient method are compared with those by steady-state ones and numerical ones. The numerical results show that the RFs of the cavity are highly sensitive to the volume of the single air bubble. A tiny bubble volume perturbation may cause a prominent RF shift even though the volume of the air bubble is smaller than 0.1% of that of the cavity. When the small air bubble moves, the RF shift will change and reach its maximum value as it is located at the middle of the cavity. As the gas volume fraction of the two-phase flow is low, both the RFs and RAs from the measurement results decrease dramatically with the increasing gas volume, and this decreasing trend gradually becomes even as the gas volume fraction increases further. These experimental results agree with the theoretical ones qualitatively. In addition, the transient method for ARS is more suitable for measuring the gas volume fraction with randomness and instantaneity than the steady-state one, because the latter could not reflect the random and instant characteristics of the mixed fluid due to the time consumption for frequency sweeping. This study will play a very important role in the quantitative measurement of the gas volume fraction of multiphase flows.

  3. Precise measurement of liquid petroleum tank volume based on data cloud analysis

    Science.gov (United States)

    Wang, Jintao; Liu, Ziyong; Zhang, Long; Guo, Ligong; Bao, Xuesong; Tong, Lin

    2010-08-01

    Metal tanks are generally used for the measurement of liquid petroleum products for fiscal or custody transfer application. One tank volume precise measurement method based on data cloud analysis was studied, which was acquired by laser scanning principle. Method of distance measurement by laser phase shift and angular measurement by optical grating were applied to acquire coordinates of points in tank shell under the control of a servo system. Direct Iterative Method (DIM) and Section Area Method (SAM) were used to process measured data for vertical and horizontal tanks respectively. In comparison experiment, one 1000m3 vertical tank and one 30m3 horizontal tank were used as test objects. In the vertical tank experiment, the largest measured radius difference between the new laser method and strapping method (international arbitrary standard) is 2.8mm. In the horizontal tank experiment, the calibration result from laser scanning method is more close to reference than manual geometric method, and the mean deviation in full-scale range of the former and latter method are 75L and 141L respectively; with the increase of liquid level, the relative errors of laser scanning method and manual geometric method become smaller, and the mean relative errors are 0.6% and 1.5% respectively. By using the method discussed, the calibration efficiency of tank volume can be improved.

  4. Measurement of average density and relative volumes in a dispersed two-phase fluid

    Science.gov (United States)

    Sreepada, Sastry R.; Rippel, Robert R.

    1992-01-01

    An apparatus and a method are disclosed for measuring the average density and relative volumes in an essentially transparent, dispersed two-phase fluid. A laser beam with a diameter no greater than 1% of the diameter of the bubbles, droplets, or particles of the dispersed phase is directed onto a diffraction grating. A single-order component of the diffracted beam is directed through the two-phase fluid and its refraction is measured. Preferably, the refracted beam exiting the fluid is incident upon a optical filter with linearly varing optical density and the intensity of the filtered beam is measured. The invention can be combined with other laser-based measurement systems, e.g., laser doppler anemometry.

  5. Evaluation of left ventricular volumes measured by magnetic resonance imaging

    DEFF Research Database (Denmark)

    Møgelvang, J; Thomsen, C; Mehlsen, J

    1986-01-01

    Left ventricular end-diastolic and end-systolic volumes were determined in 17 patients with different levels of left ventricular function by magnetic resonance imaging (MRI). A 1.5 Tesla Magnet was used obtaining ECG triggered single and multiple slices. Calculated cardiac outputs were compared...

  6. Torsional ultrasonic wave based level measurement system

    Energy Technology Data Exchange (ETDEWEB)

    Holcomb, David E. (Oak Ridge, TN); Kisner, Roger A. (Knoxville, TN)

    2012-07-10

    A level measurement system suitable for use in a high temperature and pressure environment to measure the level of coolant fluid within the environment, the system including a volume of coolant fluid located in a coolant region of the high temperature and pressure environment and having a level therein; an ultrasonic waveguide blade that is positioned within the desired coolant region of the high temperature and pressure environment; a magnetostrictive electrical assembly located within the high temperature and pressure environment and configured to operate in the environment and cooperate with the waveguide blade to launch and receive ultrasonic waves; and an external signal processing system located outside of the high temperature and pressure environment and configured for communicating with the electrical assembly located within the high temperature and pressure environment.

  7. Coupled-channel systems in a finite volume

    Science.gov (United States)

    Davoudi, Zohreh

    2012-10-01

    In this talk I will motivate studies of two-body coupled-channel systems in a finite volume in connection with the ultimate goal of studying nuclear reactions, as well as hadronic resonances, directly from lattice QCD. I will discuss how one can determine phase shifts and mixing parameters of coupled-channels such as that of pipi-KK isosinglet system from the energy spectrum in a finite volume with periodic boundary conditions. From the energy quantization condition, the volume dependence of electroweak matrix elements of two-hadron processes can also be extracted. This is necessary for studying weak processes that mix isosinglet-isotriplet two-nucleon states, e.g. proton-proton fusion. I will show how one can obtain such transition amplitudes from lattice QCD using the formalism developed.

  8. Comparative analysis of two methods for measuring sales volumes during malaria medicine outlet surveys

    OpenAIRE

    Patouillard, Edith; Kleinschmidt, Immo; Hanson, Kara; Pok, Sochea; Palafox, Benjamin; Tougher, Sarah; O’Connell, Kate; Goodman, Catherine

    2013-01-01

    Background There is increased interest in using commercial providers for improving access to quality malaria treatment. Understanding their current role is an essential first step, notably in terms of the volume of diagnostics and anti-malarials they sell. Sales volume data can be used to measure the importance of different provider and product types, frequency of parasitological diagnosis and impact of interventions. Several methods for measuring sales volumes are available, yet all have met...

  9. Comparative analysis of two methods for measuring sales volumes during malaria medicine outlet surveys.

    OpenAIRE

    Patouillard, E; Kleinschmidt, I.; Hanson, K.; Pok, S; Palafox, B; Tougher, S; O Connell, K.; Goodman, C.

    2013-01-01

    BACKGROUND There is increased interest in using commercial providers for improving access to quality malaria treatment. Understanding their current role is an essential first step, notably in terms of the volume of diagnostics and anti-malarials they sell. Sales volume data can be used to measure the importance of different provider and product types, frequency of parasitological diagnosis and impact of interventions. Several methods for measuring sales volumes are available, yet all have met...

  10. Volumes of chronic traumatic frontal brain lesions measured by MR imaging and CBF tomography

    Energy Technology Data Exchange (ETDEWEB)

    Maeder, P.; Wirsen, A.; Bajc, M.; Schalen, W.; Sjoeholm, H.; Skeidsvoll, H.; Cronqvist, S.; Ingvar, D.H. (University Hospital, Lund (Sweden). Dept. of Neuroradiology University Hospital, Lund (Sweden). Dept. of Clinical Neurophysiology University Hospital, Lund (Sweden). Dept. of Neurosurgery)

    1991-07-01

    The volumes (ml) of chronic traumatic frontal brain lesions were compared measured 'morphologically' with MR imaging (T1 and T2 weighted images) and 'functionally' with a tomographic rCBF technique (SPECT with {sup 133}Xe i.v.). The T1 volumes varied between 11 and 220 ml. The correlation between T1 and T2 volumes was 0.95, the T2 volumes being 33% larger than T1 volumes (p<0.001). The functional SPECT volumes were considerably larger (range 16-324 ml) than the MR volumes. The mean volume difference was 81% between T1 and SPECT images (p<0.001), and 35% between T2 and SPECT images (p<0.001). Correlations between the MR and SPECT volumes were also higher for T2 than T1 volumes. The volume difference is most likely explained by a functional decrease in regions around the lesion in which no morphologic change visible on MR images had taken place. MR and SPECT volume measurements were positively related to persistent lack of energy and personality changes, but only moderately related to duration of impaired consciousness and neuropsychologie outcome. (orig.).

  11. Verification and validation guidelines for high integrity systems. Volume 1

    Energy Technology Data Exchange (ETDEWEB)

    Hecht, H.; Hecht, M.; Dinsmore, G.; Hecht, S.; Tang, D. [SoHaR, Inc., Beverly Hills, CA (United States)

    1995-03-01

    High integrity systems include all protective (safety and mitigation) systems for nuclear power plants, and also systems for which comparable reliability requirements exist in other fields, such as in the process industries, in air traffic control, and in patient monitoring and other medical systems. Verification aims at determining that each stage in the software development completely and correctly implements requirements that were established in a preceding phase, while validation determines that the overall performance of a computer system completely and correctly meets system requirements. Volume I of the report reviews existing classifications for high integrity systems and for the types of errors that may be encountered, and makes recommendations for verification and validation procedures, based on assumptions about the environment in which these procedures will be conducted. The final chapter of Volume I deals with a framework for standards in this field. Volume II contains appendices dealing with specific methodologies for system classification, for dependability evaluation, and for two software tools that can automate otherwise very labor intensive verification and validation activities.

  12. Osmosensory mechanisms in cellular and systemic volume regulation

    DEFF Research Database (Denmark)

    Pedersen, Stine Helene Falsig; Kapus, András; Hoffmann, Else K

    2011-01-01

    Perturbations of cellular and systemic osmolarity severely challenge the function of all organisms and are consequently regulated very tightly. Here we outline current evidence on how cells sense volume perturbations, with particular focus on mechanisms relevant to the kidneys and to extracellular...

  13. Remote-handled transuranic system assessment appendices. Volume 2

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-11-01

    Volume 2 of this report contains six appendices to the report: Inventory and generation of remote-handled transuranic waste; Remote-handled transuranic waste site storage; Characterization of remote-handled transuranic waste; RH-TRU waste treatment alternatives system analysis; Packaging and transportation study; and Remote-handled transuranic waste disposal alternatives.

  14. Remote-handled transuranic system assessment appendices. Volume 2

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-11-01

    Volume 2 of this report contains six appendices to the report: Inventory and generation of remote-handled transuranic waste; Remote-handled transuranic waste site storage; Characterization of remote-handled transuranic waste; RH-TRU waste treatment alternatives system analysis; Packaging and transportation study; and Remote-handled transuranic waste disposal alternatives.

  15. Blood volume measurement with indocyanine green pulse spectrophotometry: dose and site of dye administration

    NARCIS (Netherlands)

    M.R. Germans; P.C. de Witt Hamer; L.J. van Boven; K.A.H. Zwinderman; G.J. Bouma

    2010-01-01

    (1) To determine the optimal administration site and dose of indocyanine green (ICG) for blood volume measurement using pulse spectrophotometry, (2) to assess the variation in repeated blood volume measurements for patients after subarachnoid hemorrhage and (3) to evaluate the safety and efficacy of

  16. Archimedes Revisited: A Faster, Better, Cheaper Method of Accurately Measuring the Volume of Small Objects

    Science.gov (United States)

    Hughes, Stephen W.

    2005-01-01

    A little-known method of measuring the volume of small objects based on Archimedes' principle is described, which involves suspending an object in a water-filled container placed on electronic scales. The suspension technique is a variation on the hydrostatic weighing technique used for measuring volume. The suspension method was compared with two…

  17. Spatial Visualization Tasks to Support Students' Spatial Structuring in Learning Volume Measurement

    Science.gov (United States)

    Revina, Shintia; Zulkardi; Darmawijoyo; van Galen, Frans

    2011-01-01

    Many prior researches found that most of students in grade five tended to have difficulty in fully grasping the concept of volume measurement because they have to build their competence in spatial structuring. The unit of volume "packing" measurement must be integrated and coordinated in three-dimension. On the other hand, it is revealed…

  18. Three-dimensional sonographic measurement of normal fetal brain volume during the second half of pregnancy

    NARCIS (Netherlands)

    N.M. Roelfsema; W.C.J. Hop (Wim); S.M. Boito; J.W. Wladimiroff (Juriy)

    2004-01-01

    textabstractObjectives: This study was undertaken to develop a three-dimensional (3D) ultrasound method of measuring fetal brain volume. Study design: Serial 3D sonographic measurements of fetal brain volume were made in 68 normal singleton pregnancies at 18 to 34 weeks of gestation. A comparison

  19. The Effect of a Finite Measurement Volume on Power Spectra from a Burst Type LDA

    DEFF Research Database (Denmark)

    Buchhave, Preben; Velte, Clara Marika; K. George, William

    2014-01-01

    We analyze the effects of a finite size measurement volume on the power spectrum computed fromdata acquired with a burst-type laser Doppler anemometer. The finite measurement volume causes temporal distortions in acquisition of the data resulting in phenomena such as finite processing time and de...

  20. Thermodynamics of small systems two volumes bound as one

    CERN Document Server

    Hill, Terrel L

    1994-01-01

    This authoritative summary of the basics of small system, or nonmacroscopic, thermodynamics was written by the field's founder. Originally published in two volumes, the text remains essential reading in an area in which the practical aim is to derive equations that provide interconnections among various thermodynamic functions. Part I introduces the basics of small system thermodynamics, exploring environmental variables, noting throughout the ways in which small thermodynamic systems differ operationally from macroscopic systems. Part II explores binding on macromolecules and aggregation, completes the discussion of environmental variables, and includes brief summaries of certain special topics, including electric and magnetic fields, spherical drops and bubbles, and polydisperse systems.

  1. Pile volume measurement by range imaging camera in indoor environment

    OpenAIRE

    C. Altuntas

    2014-01-01

    Range imaging (RIM) camera is recent technology in 3D location measurement. The new study areas have been emerged in measurement and data processing together with RIM camera. It has low-cost and fast measurement technique compared to the current measurement techniques. However its measurement accuracy varies according to effects resulting from the device and the environment. The direct sunlight is affect measurement accuracy of the camera. Thus, RIM camera should be used for indoor ...

  2. Comparison of medical of volume measurement of the prostate by transrectal ultrasound: Experiment with jelly models

    Energy Technology Data Exchange (ETDEWEB)

    Cho, Jeong Yeon; Lee, Hak Jong; Kim, Sung Hyun [Samsung Seoul Hospital, Sungkyunkwan University School of Medicine, Seoul (Korea, Republic of); Kim, Seung Hyup [Seoul National University College of Medicine, Seoul (Korea, Republic of)

    2002-03-15

    To evaluate the accuracy of measuring the volume of the prostate using the prolate ellipsoid volume calculation method (antero-posterior (AP) diameter X length X width X {pi}6) when the antero-posterior diameter of the prostate was measured on midsagittal (sagittal volume) and axial plane (axial volume).The devil's tongue jelly was used for the creation of ultrasound model of the prostate (volume: 15-40 cc) by cutting and shaping the surface. The volume in 10 prostatic models and 30 patients was measured and calculated. First, the AP diameter and length of the prostate models in midsagittal plane, and the height and width of the models in axial plane were measured for 3 times. The volume was calculated in two ways, one using the AP diameter an midsagittal plane and the other using the AP diameter in axial plane. The true volume of the model was measured using mess cylinder. The calculated volume and true volume were compared, and the accuracy of two method of measuring the prostatic volume was evaluated by Friedman test. The intraobserver variation was evaluated by General Linear Model, Repeated Measure. The reproducibility was evaluated by Cronbach's {alpha}. In vivo study was also performed in 30 patients. The prostate volume was calculated in the same manner. These volume data were analyzed by statistical method, and the intraobeserver variation was evaluated. While there was a statistically significant difference between the sagittal and true volume of the models, there was no statistical significant difference between the axial and true volumes. There was no significant intraobserver variation between both methods. The reproducibility was high in both methods with Cronbach's {alpha} of 0.977 and 0.942. The sagittal volume was larger than the axial volume in 30 patients with a statistically significant difference. There was no significant intraobserver variation in both methods. The reproducibility was high in both methods Cronbach's {alpha

  3. Carbon Dioxide Flux Measurement Systems

    Data.gov (United States)

    Oak Ridge National Laboratory — The Southern Great Plains (SGP) carbon dioxide flux (CO2 flux) measurement systems provide half-hour average fluxes of CO2, H2O (latent heat), and sensible heat. The...

  4. Two-dimensional ultrasound measurement of thyroid gland volume: a new equation with higher correlation with 3-D ultrasound measurement.

    Science.gov (United States)

    Ying, Michael; Yung, Dennis M C; Ho, Karen K L

    2008-01-01

    This study aimed to develop a new two-dimensional (2-D) ultrasound thyroid volume estimation equation using three-dimensional (3-D) ultrasound as the standard of reference, and to compare the thyroid volume estimation accuracy of the new equation with three previously reported equations. 2-D and 3-D ultrasound examinations of the thyroid gland were performed in 150 subjects with normal serum thyrotropin (TSH, thyroid-stimulating hormone) and free thyroxine (fT4) levels (63 men and 87 women, age range: 17 to 71 y). In each subject, the volume of both thyroid lobes was measured by 3-D ultrasound. On 2-D ultrasound, the craniocaudal (CC), lateromedial (LM) and anteroposterior (AP) dimensions of the thyroid lobes were measured. The equation was derived by correlating the volume of the thyroid lobes measured with 3-D ultrasound and the product of the three dimensions measured with 2-D ultrasound using linear regression analysis, in 75 subjects without thyroid nodule. The accuracy of thyroid volume estimation of the new equation and the three previously reported equations was evaluated and compared in another 75 subjects (without thyroid nodule, n = 30; with thyroid nodule, n = 45). It is suggested that volume of thyroid lobe may be estimated as: volume of thyroid lobe = 0.38.(CC.LM.AP) + 1.76. Result showed that the new equation (16.9% to 36.1%) had a significantly smaller thyroid volume estimation error than the previously reported equations (20.8% to 54.9%) (p thyroid volume estimation error when thyroid glands with nodules were examined (p thyroid volume equation, 2-D ultrasound can be a useful alternative in thyroid volume measurement when 3-D ultrasound is not available.

  5. Endovascular blood flow measurement system

    Science.gov (United States)

    Khe, A. K.; Cherevko, A. A.; Chupakhin, A. P.; Krivoshapkin, A. L.; Orlov, K. Yu

    2016-06-01

    In this paper an endovascular measurement system used for intraoperative cerebral blood flow monitoring is described. The system is based on a Volcano ComboMap Pressure and Flow System extended with analogue-to-digital converter and PC laptop. A series of measurements performed in patients with cerebrovascular pathologies allows us to introduce “velocity-pressure” and “flow rate-energy flow rate” diagrams as important characteristics of the blood flow. The measurement system presented here can be used as an additional instrument in neurosurgery for assessment and monitoring of the operation procedure. Clinical data obtained with the system are used for construction of mathematical models and patient-specific simulations. The monitoring of the blood flow parameters during endovascular interventions was approved by the Ethics Committee at the Meshalkin Novosibirsk Research Institute of Circulation Pathology and included in certain surgical protocols for pre-, intra- and postoperative examinations.

  6. Volume weighting the measure of the universe from classical slow-roll expansion

    Science.gov (United States)

    Sloan, David; Silk, Joseph

    2016-05-01

    One of the most frustrating issues in early universe cosmology centers on how to reconcile the vast choice of universes in string theory and in its most plausible high energy sibling, eternal inflation, which jointly generate the string landscape with the fine-tuned and hence relatively small number of universes that have undergone a large expansion and can accommodate observers and, in particular, galaxies. We show that such observations are highly favored for any system whereby physical parameters are distributed at a high energy scale, due to the conservation of the Liouville measure and the gauge nature of volume, asymptotically approaching a period of large isotropic expansion characterized by w =-1 . Our interpretation predicts that all observational probes for deviations from w =-1 in the foreseeable future are doomed to failure. The purpose of this paper is not to introduce a new measure for the multiverse, but rather to show how what is perhaps the most natural and well-known measure, volume weighting, arises as a consequence of the conservation of the Liouville measure on phase space during the classical slow-roll expansion.

  7. Adrenal gland volume measurement in septic shock and control patients: a pilot study

    Energy Technology Data Exchange (ETDEWEB)

    Nougaret, Stephanie; Aufort, S.; Gallix, B. [Hopital Saint Eloi, Department of Abdominal Imaging, CHU Montpellier, Montpellier, Cedex 5 (France); Jung, B.; Chanques, G.; Jaber, S. [Hopital Saint Eloi, Intensive Care Unit, Department of Critical Care and Anesthesiology: DAR B, CHU Montpellier, Montpellier, Cedex 5 (France)

    2010-10-15

    To compare adrenal gland volume in septic shock patients and control patients by using semi-automated volumetry. Adrenal gland volume and its inter-observer variability were measured with tomodensitometry using semi-automated software in 104 septic shock patients and in 40 control patients. The volumes of control and septic shock patients were compared and the relationship between volume and outcome in intensive care was studied. The mean total volume of both adrenal glands was 7.2 {+-} 2.0 cm{sup 3} in control subjects and 13.3 {+-} 4.7 cm{sup 3} for total adrenal gland volume in septic shock patients (p < 0.0001). Measurement reproducibility was excellent with a concordance correlation coefficient value of 0.87. The increasing adrenal gland volume was associated with a higher rate of survival in intensive care. The present study reports that with semi-automated software, adrenal gland volume can be measured easily and reproducibly. Adrenal gland volume was found to be nearly double in sepsis compared with control patients. The absence of increased volume during sepsis would appear to be associated with a higher rate of mortality and may represent a prognosis factor which may help the clinician to guide their strategy. (orig.)

  8. Future Wireless Networks and Information Systems Volume 1

    CERN Document Server

    2012-01-01

    This volume contains revised and extended research articles written by prominent researchers participating in ICFWI 2011 conference. The 2011 International Conference on Future Wireless Networks and Information Systems (ICFWI 2011) has been held on November 30 ~ December 1, 2011, Macao, China. Topics covered include Wireless Information Networks, Wireless Networking Technologies, Mobile Software and Services, intelligent computing, network management, power engineering, control engineering, Signal and Image Processing, Machine Learning, Control Systems and Applications, The book will offer the states of arts of tremendous advances in Wireless Networks and Information Systems and also serve as an excellent reference work for researchers and graduate students working on Wireless Networks and Information Systems.

  9. 'Orbital volume restoration rate after orbital fracture'; a CT-based orbital volume measurement for evaluation of orbital wall reconstructive effect.

    Science.gov (United States)

    Wi, J M; Sung, K H; Chi, M

    2017-01-13

    PurposeTo evaluate the effect of orbital reconstruction and factors related to the effect of orbital reconstruction by assessing of orbital volume using orbital computed tomography (CT) in cases of orbital wall fracture.MethodsIn this retrospective study, 68 patients with isolated blowout fractures were evaluated. The volumes of orbits and herniated orbital tissues were determined by CT scans using a three-dimensional reconstruction technique (the Eclipse Treatment Planning System). Orbital CT was performed preoperatively, immediately after surgery, and at final follow ups (minimum of 6 months). We evaluated the reconstructive effect of surgery making a new formula, 'orbital volume reconstruction rate' from orbital volume differences between fractured and contralateral orbits before surgery, immediately after surgery, and at final follow up.ResultsMean volume of fractured orbits before surgery was 23.01±2.60 cm(3) and that of contralateral orbits was 21.31±2.50 cm(3) (P=0.005). Mean volume of the fractured orbits immediately after surgery was 21.29±2.42 cm(3), and that of the contralateral orbits was 21.33±2.52 cm(3) (P=0.921). Mean volume of fractured orbits at final follow up was 21.50±2.44 cm(3), and that of contralateral orbits was 21.32±2.50 cm(3) (P=0.668). The mean orbital volume reconstruction rate was 100.47% immediately after surgery and 99.17% at final follow up. No significant difference in orbital volume reconstruction rate was observed with respect to fracture site or orbital implant type. Patients that underwent operation within 14 days of trauma had a better reconstruction rate at final follow up than patients who underwent operation over 14 days after trauma (P=0.039).ConclusionComputer-based measurements of orbital fracture volume can be used to evaluate the reconstructive effect of orbital implants and provide useful quantitative information. Significant reduction of orbital volume is observed immediately after orbital wall

  10. Tree Root System Characterization and Volume Estimation by Terrestrial Laser Scanning and Quantitative Structure Modeling

    Directory of Open Access Journals (Sweden)

    Aaron Smith

    2014-12-01

    Full Text Available The accurate characterization of three-dimensional (3D root architecture, volume, and biomass is important for a wide variety of applications in forest ecology and to better understand tree and soil stability. Technological advancements have led to increasingly more digitized and automated procedures, which have been used to more accurately and quickly describe the 3D structure of root systems. Terrestrial laser scanners (TLS have successfully been used to describe aboveground structures of individual trees and stand structure, but have only recently been applied to the 3D characterization of whole root systems. In this study, 13 recently harvested Norway spruce root systems were mechanically pulled from the soil, cleaned, and their volumes were measured by displacement. The root systems were suspended, scanned with TLS from three different angles, and the root surfaces from the co-registered point clouds were modeled with the 3D Quantitative Structure Model to determine root architecture and volume. The modeling procedure facilitated the rapid derivation of root volume, diameters, break point diameters, linear root length, cumulative percentages, and root fraction counts. The modeled root systems underestimated root system volume by 4.4%. The modeling procedure is widely applicable and easily adapted to derive other important topological and volumetric root variables.

  11. Measuring Complexity of SAP Systems

    Directory of Open Access Journals (Sweden)

    Ilja Holub

    2016-10-01

    Full Text Available The paper discusses the reasons of complexity rise in ERP system SAP R/3. It proposes a method for measuring complexity of SAP. Based on this method, the computer program in ABAP for measuring complexity of particular SAP implementation is proposed as a tool for keeping ERP complexity under control. The main principle of the measurement method is counting the number of items or relations in the system. The proposed computer program is based on counting of records in organization tables in SAP.

  12. Semiautomatic regional segmentation to measure orbital fat volumes in thyroid-associated ophthalmopathy. A validation study.

    Science.gov (United States)

    Comerci, M; Elefante, A; Strianese, D; Senese, R; Bonavolontà, P; Alfano, B; Bonavolontà, B; Brunetti, A

    2013-08-01

    This study was designed to validate a novel semi-automated segmentation method to measure regional intra-orbital fat tissue volume in Graves' ophthalmopathy. Twenty-four orbits from 12 patients with Graves' ophthalmopathy, 24 orbits from 12 controls, ten orbits from five MRI study simulations and two orbits from a digital model were used. Following manual region of interest definition of the orbital volumes performed by two operators with different levels of expertise, an automated procedure calculated intra-orbital fat tissue volumes (global and regional, with automated definition of four quadrants). In patients with Graves' disease, clinical activity score and degree of exophthalmos were measured and correlated with intra-orbital fat volumes. Operator performance was evaluated and statistical analysis of the measurements was performed. Accurate intra-orbital fat volume measurements were obtained with coefficients of variation below 5%. The mean operator difference in total fat volume measurements was 0.56%. Patients had significantly higher intra-orbital fat volumes than controls (p<0.001 using Student's t test). Fat volumes and clinical score were significantly correlated (p<0.001). The semi-automated method described here can provide accurate, reproducible intra-orbital fat measurements with low inter-operator variation and good correlation with clinical data.

  13. Measurement of transplanted pancreatic volume using computed tomography: reliability by intra- and inter-observer variability

    Energy Technology Data Exchange (ETDEWEB)

    Lundqvist, Eva; Segelsjoe, Monica; Magnusson, Anders [Uppsala Univ., Dept. of Radiology, Oncology and Radiation Science, Section of Radiology, Uppsala (Sweden)], E-mail: eva.lundqvist.8954@student.uu.se; Andersson, Anna; Biglarnia, Ali-Reza [Dept. of Surgical Sciences, Section of Transplantation Surgery, Uppsala Univ. Hospital, Uppsala (Sweden)

    2012-11-15

    Background Unlike other solid organ transplants, pancreas allografts can undergo a substantial decrease in baseline volume after transplantation. This phenomenon has not been well characterized, as there are insufficient data on reliable and reproducible volume assessments. We hypothesized that characterization of pancreatic volume by means of computed tomography (CT) could be a useful method for clinical follow-up in pancreas transplant patients. Purpose To evaluate the feasibility and reliability of pancreatic volume assessment using CT scan in transplanted patients. Material and Methods CT examinations were performed on 21 consecutive patients undergoing pancreas transplantation. Volume measurements were carried out by two observers tracing the pancreatic contours in all slices. The observers performed the measurements twice for each patient. Differences in volume measurement were used to evaluate intra- and inter-observer variability. Results The intra-observer variability for the pancreatic volume measurements of Observers 1 and 2 was found to be in almost perfect agreement, with an intraclass correlation coefficient (ICC) of 0.90 (0.77-0.96) and 0.99 (0.98-1.0), respectively. Regarding inter-observer validity, the ICCs for the first and second measurements were 0.90 (range, 0.77-0.96) and 0.95 (range, 0.85-0.98), respectively. Conclusion CT volumetry is a reliable and reproducible method for measurement of transplanted pancreatic volume.

  14. Accuracy of MRI volume measurements of breast lesions: comparison between automated, semiautomated and manual assessment

    Energy Technology Data Exchange (ETDEWEB)

    Rominger, Marga B.; Fournell, Daphne; Nadar, Beenarose Thanka; Figiel, Jens H.; Keil, Boris; Heverhagen, Johannes T. [Philipps University, Department of Radiology, Marburg (Germany); Behrens, Sarah N.M. [MeVis GmbH, Bremen (Germany)

    2009-05-15

    The aim of this study was to investigate the efficacy of a dedicated software tool for automated and semiautomated volume measurement in contrast-enhanced (CE) magnetic resonance mammography (MRM). Ninety-six breast lesions with histopathological workup (27 benign, 69 malignant) were re-evaluated by different volume measurement techniques. Volumes of all lesions were extracted automatically (AVM) and semiautomatically (SAVM) from CE 3D MRM and compared with manual 3D contour segmentation (manual volume measurement, MVM, reference measurement technique) and volume estimates based on maximum diameter measurement (MDM). Compared with MVM as reference method MDM, AVM and SAVM underestimated lesion volumes by 63.8%, 30.9% and 21.5%, respectively, with significantly different accuracy for benign (102.4%, 18.4% and 11.4%) and malignant (54.9%, 33.0% and 23.1%) lesions (p<0.05). Inter- and intraobserver reproducibility was best for AVM (mean difference {+-}2SD, 1.0{+-}9.7% and 1.8{+-}12.1%) followed by SAVM (4.3{+-}25.7% and 4.3{+-}7.9%), MVM (2.3{+-}38.2% and 8.6{+-}31.8%) and MDM (33.9{+-}128.4% and 9.3{+-}55.9%). SAVM is more accurate for volume assessment of breast lesions than MDM and AVM. Volume measurement is less accurate for malignant than benign lesions. (orig.)

  15. Mars power system concept definition study. Volume 1: Study results

    Science.gov (United States)

    Littman, Franklin D.

    1994-12-01

    A preliminary top level study was completed to define power system concepts applicable to Mars surface applications. This effort included definition of power system requirements and selection of power systems with the potential for high commonality. These power systems included dynamic isotope, Proton Exchange Membrane (PEM) regenerative fuel cell, sodium sulfur battery, photovoltaic, and reactor concepts. Design influencing factors were identified. Characterization studies were then done for each concept to determine system performance, size/volume, and mass. Operations studies were done to determine emplacement/deployment maintenance/servicing, and startup/shutdown requirements. Technology development roadmaps were written for each candidate power system (included in Volume 2). Example power system architectures were defined and compared on a mass basis. The dynamic isotope power system and nuclear reactor power system architectures had significantly lower total masses than the photovoltaic system architectures. Integrated development and deployment time phasing plans were completed for an example DIPS and reactor architecture option to determine the development strategies required to meet the mission scenario requirements.

  16. Airborne Atmospheric Aerosol Measurement System

    Science.gov (United States)

    Ahn, K.; Park, Y.; Eun, H.; Lee, H.

    2015-12-01

    It is important to understand the atmospheric aerosols compositions and size distributions since they greatly affect the environment and human health. Particles in the convection layer have been a great concern in global climate changes. To understand these characteristics satellite, aircraft, and radio sonde measurement methods have usually been used. An aircraft aerosol sampling using a filter and/or impactor was the method commonly used (Jay, 2003). However, the flight speed particle sampling had some technical limitations (Hermann, 2001). Moreover, the flight legal limit, altitude, prohibited airspace, flight time, and cost was another demerit. To overcome some of these restrictions, Tethered Balloon Package System (T.B.P.S.) and Recoverable Sonde System(R.S.S.) were developed with a very light optical particle counter (OPC), impactor, and condensation particle counter (CPC). Not only does it collect and measure atmospheric aerosols depending on altitudes, but it also monitors the atmospheric conditions, temperature, humidity, wind velocity, pressure, GPS data, during the measurement (Eun, 2013). In this research, atmospheric aerosol measurement using T.B.P.S. in Ansan area is performed and the measurement results will be presented. The system can also be mounted to an unmanned aerial vehicle (UAV) and create an aerial particle concentration map. Finally, we will present measurement data using Tethered Balloon Package System (T.B.P.S.) and R.S.S (Recoverable Sonde System).

  17. Blood volume measurements in gopher snakes, using autologous 51Cr-labeled red blood cells.

    Science.gov (United States)

    Smeller, J M; Bush, M; Seal, U S

    1978-02-01

    Blood volume determinations were performed in 5 anesthetized gopher snakes (Pituophis melanoleucus catenifer) by means of a 51Cr-labeled red blood cell (RBC) method. The mean blood volume was 52.8 ml/kg of body weight (+/- 6.21 SE). Previous blood volume measurements have not been reported for this species. The RBC survival rate was estimated to be greater than 660 days. The RBC survival rate is long, but it cannot be determined accurately by this method.

  18. Finite Volume Evolution Galerkin Methods for Nonlinear Hyperbolic Systems

    Science.gov (United States)

    Lukáčová-Medvid'ová, M.; Saibertová, J.; Warnecke, G.

    2002-12-01

    We present new truly multidimensional schemes of higher order within the frame- work of finite volume evolution Galerkin (FVEG) methods for systems of nonlinear hyperbolic conservation laws. These methods couple a finite volume formulation with approximate evolution operators. The latter are constructed using the bicharacteristics of the multidimensional hyperbolic system, such that all of the infinitely many directions of wave propagation are taken into account. Following our previous results for the wave equation system, we derive approximate evolution operators for the linearized Euler equations. The integrals along the Mach cone and along the cell interfaces are evaluated exactly, as well as by means of numerical quadratures. The influence of these numerical quadratures will be discussed. Second-order resolution is obtained using a conservative piecewise bilinear recovery and the midpoint rule approximation for time integration. We prove error estimates for the finite volume evolution Galerkin scheme for linear systems with constant coefficients. Several numerical experiments for the nonlinear. Euler equations, which confirm the accuracy and good multidimensional behavior of the FVEG schemes, are presented as well.

  19. Conceptual design and systems analysis of photovoltaic systems. Volume II. Study results. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Kirpich, A.

    1977-03-19

    This investigation of terrestrial PV systems considered the technical and economic feasibility for systems in three size categories: a small system of about 12 kW peak output for on-site residential use; a large 1500 MW central power plant contributing to the bulk energy of a utility system power grid; and an intermediate size system of about 250 kW for use on public or commercial buildings. In each category, conceptual designs were developed, performance was analyzed for a range of climatic regions, economic analyses were performed, and assessments were made of pertinent institutional issues. The report consists of three volumes. Volume I contains a Study Summary of the major study results. This volume contains the detailed results pertaining to on-site residential photovoltaic systems, central power plant photovoltaic systems, and intermediate size systems applied to commercial and public buildings. Volume III contains supporting appendix material. (WHK)

  20. Hanford 67-series: a volume of atmospheric field diffusion measurements

    Energy Technology Data Exchange (ETDEWEB)

    Nickola, P.W.

    1977-11-01

    This volume documents atmospheric diffusion experiments carried out at the Hanford reservation during the period 1967 to 1973. A total of 103 tracer releases during 54 release periods is tabulated. Multi-tracer releases (generally from different elevations) were made during most of the experimental periods. Release heights varied from ground level to an elevation of 111 m. Tracers were sampled simultaneously on as many as 10 arcs at distances of up to 12.8 km from the tracer release point. As many as 718 field sampling locations were employed during some of the experiments. Vertical profiles of concentration were monitored on towers during 23 of the 54 release periods. Concurrent vertical profiles of mean temperature, of mean wind speed and direction, and of direction standard deviation are also tabled for elevations up to 122 m.

  1. HLS bunch current measurement system

    Institute of Scientific and Technical Information of China (English)

    2011-01-01

    Bunch current is an important parameter for studying the injection fill-pattern in the storage ring and the instability threshold of the bunch, and the bunch current monitor also is an indispensable tool for the top-up injection. A bunch current measurement (BCM) system has been developed to meet the needs of the upgrade project of Hefei Light Source (HLS). This paper presents the layout of the BCM system. The system based on a high-speed digital oscilloscope can be used to measure the bunch current and synchronous phase shift. To obtain the absolute value of bunch-by-bunch current, the calibration coefficient is measured and analyzed. Error analysis shows that the RMS of bunch current is less than 0.01 mA when bunch current is about 5 mA, which can meet project requirement.

  2. Practical do-it-yourself device for accurate volume measurement of breast.

    Science.gov (United States)

    Tezel, E; Numanoğlu, A

    2000-03-01

    A simple and accurate method of measuring differences in breast volume based on Archimedes' principle is described. In this method, a plastic container is placed on the breast of the patient who is lying in supine position. While the breast occupies part of the container, the remaining part is filled with water and the volume is measured. This method allows the measurement of the volume differences of asymmetric breasts and also helps the surgeon to estimate the size of the prosthesis to be used in augmentation mammaplasty.

  3. Measuring stone volume - three-dimensional software reconstruction or an ellipsoid algebra formula?

    Science.gov (United States)

    Finch, William; Johnston, Richard; Shaida, Nadeem; Winterbottom, Andrew; Wiseman, Oliver

    2014-04-01

    To determine the optimal method for assessing stone volume, and thus stone burden, by comparing the accuracy of scalene, oblate, and prolate ellipsoid volume equations with three-dimensional (3D)-reconstructed stone volume. Kidney stone volume may be helpful in predicting treatment outcome for renal stones. While the precise measurement of stone volume by 3D reconstruction can be accomplished using modern computer tomography (CT) scanning software, this technique is not available in all hospitals or with routine acute colic scanning protocols. Therefore, maximum diameters as measured by either X-ray or CT are used in the calculation of stone volume based on a scalene ellipsoid formula, as recommended by the European Association of Urology. In all, 100 stones with both X-ray and CT (1-2-mm slices) were reviewed. Complete and partial staghorn stones were excluded. Stone volume was calculated using software designed to measure tissue density of a certain range within a specified region of interest. Correlation coefficients among all measured outcomes were compared. Stone volumes were analysed to determine the average 'shape' of the stones. The maximum stone diameter on X-ray was 3-25 mm and on CT was 3-36 mm, with a reasonable correlation (r = 0.77). Smaller stones (15 mm towards scalene ellipsoids. There was no difference in stone shape by location within the kidney. As the average shape of renal stones changes with diameter, no single equation for estimating stone volume can be recommended. As the maximum diameter increases, calculated stone volume becomes less accurate, suggesting that larger stones have more asymmetric shapes. We recommend that research looking at stone clearance rates should use 3D-reconstructed stone volumes when available, followed by prolate, oblate, or scalene ellipsoid formulas depending on the maximum stone diameter. © 2013 The Authors. BJU International © 2013 BJU International.

  4. Molar Volume Analysis of Molten Ni-Al-Co Alloy by Measuring the Density

    Institute of Scientific and Technical Information of China (English)

    XIAO Feng; FANG Liang; FU Yuechao; YANG Lingchuan

    2004-01-01

    The density of molten Ni-Al-Co alloys was measured in the temperature range of 1714~1873K using a modified pycnometric method, and the molar volume of molten alloys was analyzed. The density of molten Ni-Al-Co alloys was found to decrease with increasing temperature and Co concentration in alloys. The molar volume of molten Ni-Al-Co alloys increases with increasing Co concentration in alloys. The molar volume of molten Ni-Al-Co alloys shows a negative deviation from the linear molar volume.

  5. Measurement of mobile antenna systems

    CERN Document Server

    Arai, Hiroyuki

    2012-01-01

    If you're involved with the design, installation or maintenance of mobile antenna systems, this thoroughly revised and updated edition of a classic Artech book offers you the most current and comprehensive coverage of all the mandatory measurement techniques you need for your work in the field. This Second Edition presents critical new material in key areas, including radiation efficiency measurement, mobile phone usage position, and MIMO (multiple-input/multiple-output) antennas.This unique resource provides in-depth examinations of all relevant mobile antenna measurement theories, along with

  6. Idaho field experiment 1981. Volume 2: measurement data

    Energy Technology Data Exchange (ETDEWEB)

    Start, G E; Sagendorf, J F; Ackermann, G R; Cate, J H; Hukari, N F; Dickson, C R

    1984-04-01

    The 1981 Idaho Field Experiment was conducted in southeastern Idaho over the upper Snake River Plain. Nine test-day case studies were conducted between July 15 and 30, 1981. Releases of SF/sub 6/ gaseous tracer were made for 8-hour periods from 46m above ground. Tracer was sampled hourly, for 12 sequential hours, at about 100 locations within an area 24km square. Also, a single total integrated sample of about 30 hours duration was collected at approximately 100 sites within an area 48 by 72km square (using 6km spacings). Extensive tower profiles of meteorology at the release point were collected. RAWINSONDES, RABALS and PIBALS were collected at 3 to 5 sites. Horizontal, low-altitude winds were monitored using the INEL MESONET. SF/sub 6/ tracer plume releases were marked with co-located oil fog releases and bi-hourly sequential launches of tetroon pairs. Aerial LIDAR observations of the oil fog plume and airborne samples of SF/sub 6/ were collected. High altitude aerial photographs of daytime plumes were collected. Volume II lists the data in tabular form or cites the special supplemental reports by other participating contractors. While the primary user file and the data archive are maintained on 9 track/1600 cpi magnetic tapes, listings of the individual values are provided for the user who either cannot utilize the tapes or wishes to preview the data. The accuracies and quality of these data are described.

  7. The SIFT hardware/software systems. Volume 2: Software listings

    Science.gov (United States)

    Palumbo, Daniel L.

    1985-01-01

    This document contains software listings of the SIFT operating system and application software. The software is coded for the most part in a variant of the Pascal language, Pascal*. Pascal* is a cross-compiler running on the VAX and Eclipse computers. The output of Pascal* is BDX-390 assembler code. When necessary, modules are written directly in BDX-390 assembler code. The listings in this document supplement the description of the SIFT system found in Volume 1 of this report, A Detailed Description.

  8. Numerical simulations of volume holographic imaging system resolution characteristics

    Science.gov (United States)

    Sun, Yajun; Jiang, Zhuqing; Liu, Shaojie; Tao, Shiquan

    2009-05-01

    Because of the Bragg selectivity of volume holographic gratings, it helps VHI system to optically segment the object space. In this paper, properties of point-source diffraction imaging in terms of the point-spread function (PSF) are investigated, and characteristics of depth and lateral resolutions in a VHI system is numerically simulated. The results show that the observed diffracted field obviously changes with the displacement in the z direction, and is nearly unchanged with displacement in the x and y directions. The dependence of the diffracted imaging field on the z-displacement provides a way to possess 3-D image by VHI.

  9. A technique for fast and accurate measurement of hand volumes using Archimedes' principle.

    Science.gov (United States)

    Hughes, S; Lau, J

    2008-03-01

    A new technique for measuring hand volumes using Archimedes principle is described. The technique involves the immersion of a hand in a water container placed on an electronic balance. The volume is given by the change in weight divided by the density of water. This technique was compared with the more conventional technique of immersing an object in a container with an overflow spout and collecting and weighing the volume of overflow water. The hand volume of two subjects was measured. Hand volumes were 494 +/- 6 ml and 312 +/- 7 ml for the immersion method and 476 +/- 14 ml and 302 +/- 8 ml for the overflow method for the two subjects respectively. Using plastic test objects, the mean difference between the actual and measured volume was -0.3% and 2.0% for the immersion and overflow techniques respectively. This study shows that hand volumes can be obtained more quickly than the overflow method. The technique could find an application in clinics where frequent hand volumes are required.

  10. Process simulator for wind turbine control. Volume 2. System analyses; Processimulator voor windturbinebesturingen. Volume 2. Systeemanalyses

    Energy Technology Data Exchange (ETDEWEB)

    Van der Hooft, E.L.; Verbruggen, T.W.; Van Engelen, T.G. [ECN Wind Energy, Petten (Netherlands)

    2002-10-01

    Because of upscaling and less accessible offshore sites control systems of wind turbines must be tested in advance to fulfill requirements of reliability. By means of process simulations the operation and performance of the control system and how it deals with failures of components and subsystems and extreme operating conditions can be assessed. In a previous report (Volume 1) attention is paid to the development of the planned real-time process simulation tool WindConTest (Wind Turbine Control Systems Test, Evaluation and Simulation Tool). In this volume results of system analyses for wind turbines with constant speed and variable speed are presented. Based on those results process models and programs can be deducted in order to realize a process simulation tool in phase 2 of the project. [Dutch] Door opschaling en minder toegankelijke offshore locaties is vooraf testen van besturingssystemen van windturbines steeds belangrijker om te kunnen voldoen aan hoge betrouwbaarheidseisen. Met processimulaties kan beoordeeld worden of het besturingssysteem het falen van componenten en (deel)systemen naar behoren afhandelt en of extreme bedrijfstoestanden goed worden doorstaan. Het project, met als einddoel het real-time processimulatie-gereedschap voor windturbine besturingssystemen, WINDCONTEST, bestaat uit twee fasen. De werkzaamheden in fase I betreffen probleemanalyse en systeemanalyse, in de voorziene fase II zijn dit modellering en implementatie. Systeemanalyses zijn uitgevoerd voor windturbines met constant toerental en variabel toerental. De analyses geven invullingen aan de inventarisatie- en definitietaak. In het rapport 'systeemanalyses' worden de definitie resultaten beschreven volgens de werkwijze zoals bepaald in het eerste rapport (probleemanalyse). De inventarisatieresultaten bevatten veelal specifieke windturbine gegevens en zijn daarom opgenomen in vertrouwelijke annexen, die apart zijn uitgebracht. Op basis van de analyseresultaten kunnen in

  11. Special Properties of Coherence Scanning Interferometers for large Measurement Volumes

    Science.gov (United States)

    Bauer, W.

    2011-08-01

    In contrast to many other optical methods the uncertainty of Coherence Scanning Interferometer (CSI) in vertical direction is independent from the field of view. Therefore CSIs are ideal instruments for measuring 3D-profiles of larger areas (36×28mm2, e.g.) with high precision. This is of advantage for the determination of form parameters like flatness, parallelism and steps heights within a short time. In addition, using a telecentric beam path allows measurements of deep lying surfaces (automotive suppliers or from the steel industry.

  12. Limb volume measurement: from the past methods to optoelectronic technologies, bioimpedance analysis and laser based devices.

    Science.gov (United States)

    Cavezzi, A; Schingale, F; Elio, C

    2010-10-01

    Accurate measurement of limb volume is considered crucial to lymphedema management. Various non-invasive methods may be used and have been validated in recent years, though suboptimal standardisation has been highlighted in different publications.

  13. Variation in the measurement of cranial volume and surface area using 3D laser scanning technology.

    Science.gov (United States)

    Sholts, Sabrina B; Wärmländer, Sebastian K T S; Flores, Louise M; Miller, Kevin W P; Walker, Phillip L

    2010-07-01

    Three-dimensional (3D) laser scanner models of human crania can be used for forensic facial reconstruction, and for obtaining craniometric data useful for estimating age, sex, and population affinity of unidentified human remains. However, the use of computer-generated measurements in a casework setting requires the measurement precision to be known. Here, we assess the repeatability and precision of cranial volume and surface area measurements using 3D laser scanner models created by different operators using different protocols for collecting and processing data. We report intraobserver measurement errors of 0.2% and interobserver errors of 2% of the total area and volume values, suggesting that observer-related errors do not pose major obstacles for sharing, combining, or comparing such measurements. Nevertheless, as no standardized procedure exists for area or volume measurements from 3D models, it is imperative to report the scanning and postscanning protocols employed when such measurements are conducted in a forensic setting.

  14. How to get spatial resolution inside probe volumes of commercial 3D LDA systems

    Energy Technology Data Exchange (ETDEWEB)

    Strunck, V.; Sodomann, T.; Mueller, H.; Dopheide, D. [Section of Fluid Flow Measuring Techniques, Physikalisch-Technische Bundesanstalt, Bundesallee 100, 38116, Braunschweig (Germany)

    2004-01-01

    In laser Doppler anemometry (LDA) it is often the aim to determine the velocity profile for a given fluid flow. The spatial resolution of such velocity profiles is limited in principal by the size of the probe volume. The method of using time of flight data from two probe volumes allows improvements of the spatial resolution by at least one order of magnitude and measurements of small-scale velocity profiles inside the measuring volume along the optical axis of commercial available 3D anemometers without moving the probe. No change of the optical set-up is necessary. An increased spatial resolution helps to acquire more precise data in areas where the flow velocity changes rapidly as shown in the vicinity of the stagnation point of a cuboid. In the overlapping region of three measuring volumes a spatially resolved 3D velocity vector profile is obtained in the direction of the optical axis in near plane flow conditions. In plane laminar flows the probe volume is extended by a few millimetres. The limitation of the method to a plane flow is that it would require a two-component LDA in a very special off-axis arrangement, but this arrangement is available in most commercial 3D systems. (orig.)

  15. System Engineering Concept Demonstration, System Engineering Needs. Volume 2

    Science.gov (United States)

    1992-12-01

    support, executable specification, quality assessment), management support, and communications (especially for organizationally or geographically ...34* Technical Management Plan (equivalent to SEMP) "* New Program Startup Guide "* System Specification "* Segement Specifications "* Design Analysis

  16. The effect of fiber orientation on volume measurement using conductance catheter techniques.

    Science.gov (United States)

    Thaijiam, C; Gale, T J

    2006-01-01

    Estimation of parallel conductance using the impedance electrode technique is usually done assuming isotropic conditions. This may not be the best solution since the myocardium is an anisotropic material. This paper exposes the effect of fiber orientation for volume measurement using a conductor model with asymmetrical source electrodes. Simulation results show calculated volumes between surrounding materials with and without myocardial fiber orientation included in the model. We plan to extend these study results to the real heart for developing conductance catheter techniques for use in blood volume measurements in the right ventricle.

  17. Measuring the volume of uterine fibroids using 2- and 3-dimensional ultrasound and comparison with histopathology.

    Science.gov (United States)

    Zivković, Nikica; Zivković, Kreiimir; Despot, Albert; Paić, Josip; Zelić, Ana

    2012-12-01

    The aim of this study was clinical testing of the reliability and usability of three-dimensional (3D) and two-dimensional (2D) ultrasound (US) technology. The ultimate aim and purpose of this study was to establish ultrasound methods, standards and protocols for determining the volume of any gynecologic organ or tumor. The study included 31 women in reproductive age and postmenopause. All patients were examined with a RIC 5-9 3D-endovaginal probe (4.3-7.5 MHz) on a Voluson 730 Pro ultrasound device. The volume of myomas was measured by using the existing 2D and 3D ultrasound methods on the above mentioned device. All patients underwent myomectomy or hysterectomy due to clinically and ultrasonographically diagnosed uterine myomas indicating operative intervention. After the operation, the pathologist determined the volume of removed myomas by measuring them in a gauge bowl containing water, i.e. using Archimedes' principle (lift), serving as the control group with histopathologic diagnosis. A total of 155 myoma volumes were processed on 2D display, 31 myoma volumes were preoperatively measured on 3D display and 31 myoma volumes were measured by the pathologist. The values of US measurements for each US method were expressed as mean value of all measurements of myoma volumes. Statistical processing of the results and Student's t-test for independent samples revealed that the 2nd examined US method (measuring of myoma by using an ellipse and the longer tumor diameter) and 4th examined US method (measuring of myoma by using the longer and shorter tumor diameters together with establishing their mean values) in 2D US technique, as well as the 6th examined US method in 3D US technique showed no significant measurement differences in comparison with control measurement in a gauge bowl containing water (p < 0.05), indicating acceptability of the US methods for verifying tumor volumes. The standard error in determining the volume of myomas by the above US methods varied

  18. Experience of ENEA in measuring volume and/or mass of input solutions needs for further R&D

    Energy Technology Data Exchange (ETDEWEB)

    Dionisi, M.

    1992-05-01

    Solution volume and mass measurements are an essential component of any system to control and account for nuclear materials that are processed or stored in a liquid medium, both from the operators and the safeguards authorities points of view. ENEA (Italian Agency for Energy, New Technologies and the Environment) engaged a comprehensive R&D programme and, in cooperation with national and international organizations, undertook theoretical and experimental studies on tank volume calibration and measurements in order to fill the recognized technological gap. The ENEA activities included: theoretical and experimental studies; development of an improved time domain reflectometer system for solution level measurement in an accountability tank; in-field testing of tracer techniques for volume and mass determination in accountability tanks. This report presents the experience of ENEA in the field of R&D on solution volume and mass determination; gives impressions and judgements over the state-of-the-art and of practice of these measurements; and provides suggestions on what could and/or must be improved, indicating further R&D activities.

  19. Special Properties of Coherence Scanning Interferometers for large Measurement Volumes

    Energy Technology Data Exchange (ETDEWEB)

    Bauer, W, E-mail: W.bauer@polytec.de [Polytec GmbH, Polytec Platz 1-7, 76337 Waldbronn (Germany)

    2011-08-19

    In contrast to many other optical methods the uncertainty of Coherence Scanning Interferometer (CSI) in vertical direction is independent from the field of view. Therefore CSIs are ideal instruments for measuring 3D-profiles of larger areas (36x28mm{sup 2}, e.g.) with high precision. This is of advantage for the determination of form parameters like flatness, parallelism and steps heights within a short time. In addition, using a telecentric beam path allows measurements of deep lying surfaces (<70mm) and the determination of form parameters with large step-heights. The lateral and spatial resolution, however, are reduced. In this presentation different metrological characteristics together with their potential errors are analyzed for large-scale measuring CSIs. Therefore these instruments are ideal tools in quality control for good/bad selections, e.g. The consequences for the practical use in industry and for standardization are discussed by examples of workpieces of automotive suppliers or from the steel industry.

  20. Understanding Process Performance Measurement Systems

    Directory of Open Access Journals (Sweden)

    Ljubica MilanoviÊ Glavan

    2011-01-01

    Full Text Available The purpose of this paper is to analyze the current state of Process Performance Measurement Systems (PPMS by means of a systematic review of literature. The PPMS literature is reviewed using a systematic approach. Based on an extensive literature review only twelve articles that contain the term PPMS in the title were found. The literature analysis showed that PPMS is a relatively new topic in the area of performance measurement. In order to understand PPMS, it was crucial to explain the concepts of business process management, business performance measurement and Performance Measurement System (PMS which are well known and used in the literature and practice. PPMS is a special type of PMS that should be used in process-oriented organizations. Limitations of this research lie in the fact that all the conclusions were derived only from the literature, not empirical research. The results presented in the paper continue towards providing an updated overview of the current state of performance measurement, especially PPMS in order to identify the existing research gaps on which ongoing and future research efforts regarding this topic can be focused.

  1. DC Magnetics Measurement System Design

    Science.gov (United States)

    Mastny, Timothy

    2012-01-01

    This report will detail the updates to the magnetics measurement system design and testing procedures that are required for performing static (DC) magnetics testing of future flight hardware. An older magnetics testing system had to be integrated with new procedures and hardware to meet the demands of future testing programs and accommodate an upcoming magnetics tests. The next test will be for the Geostationary Operational Environmental Satellite R-Series (GOES-R), which will verify that the SAFT Battery component meets its specifications for magnetic cleanliness. The satellite is scheduled to launch in 2015 with magnetics testing to be completed on the battery in November 2012.

  2. OMERACT Rheumatoid Arthritis Magnetic Resonance Imaging Studies. Exercise 5: an international multicenter reliability study using computerized MRI erosion volume measurements

    DEFF Research Database (Denmark)

    Bird, P; Ejbjerg, B; McQueen, F

    2003-01-01

    Scoring erosions on magnetic resonance imaging (MRI) is one method of estimating damage in patients with rheumatoid arthritis (RA), but it has limitations. The aim of this pilot study was to assess the feasibility and inter-reader reliability of computer assisted erosion volume estimation...... with metacarpophalangeal (MCP) joints 2 to 5 of the dominant hand included in the field of view. Three readers were instructed to grade MCP 2 and 3 using the OMERACT grading system and then to measure the erosion volume of the same joints using OSIRIS software. The inter-reader reliability of the grading method...

  3. Artificial Neural Network-Based System for PET Volume Segmentation

    Directory of Open Access Journals (Sweden)

    Mhd Saeed Sharif

    2010-01-01

    Full Text Available Tumour detection, classification, and quantification in positron emission tomography (PET imaging at early stage of disease are important issues for clinical diagnosis, assessment of response to treatment, and radiotherapy planning. Many techniques have been proposed for segmenting medical imaging data; however, some of the approaches have poor performance, large inaccuracy, and require substantial computation time for analysing large medical volumes. Artificial intelligence (AI approaches can provide improved accuracy and save decent amount of time. Artificial neural networks (ANNs, as one of the best AI techniques, have the capability to classify and quantify precisely lesions and model the clinical evaluation for a specific problem. This paper presents a novel application of ANNs in the wavelet domain for PET volume segmentation. ANN performance evaluation using different training algorithms in both spatial and wavelet domains with a different number of neurons in the hidden layer is also presented. The best number of neurons in the hidden layer is determined according to the experimental results, which is also stated Levenberg-Marquardt backpropagation training algorithm as the best training approach for the proposed application. The proposed intelligent system results are compared with those obtained using conventional techniques including thresholding and clustering based approaches. Experimental and Monte Carlo simulated PET phantom data sets and clinical PET volumes of nonsmall cell lung cancer patients were utilised to validate the proposed algorithm which has demonstrated promising results.

  4. Artificial Neural Network-Based System for PET Volume Segmentation.

    Science.gov (United States)

    Sharif, Mhd Saeed; Abbod, Maysam; Amira, Abbes; Zaidi, Habib

    2010-01-01

    Tumour detection, classification, and quantification in positron emission tomography (PET) imaging at early stage of disease are important issues for clinical diagnosis, assessment of response to treatment, and radiotherapy planning. Many techniques have been proposed for segmenting medical imaging data; however, some of the approaches have poor performance, large inaccuracy, and require substantial computation time for analysing large medical volumes. Artificial intelligence (AI) approaches can provide improved accuracy and save decent amount of time. Artificial neural networks (ANNs), as one of the best AI techniques, have the capability to classify and quantify precisely lesions and model the clinical evaluation for a specific problem. This paper presents a novel application of ANNs in the wavelet domain for PET volume segmentation. ANN performance evaluation using different training algorithms in both spatial and wavelet domains with a different number of neurons in the hidden layer is also presented. The best number of neurons in the hidden layer is determined according to the experimental results, which is also stated Levenberg-Marquardt backpropagation training algorithm as the best training approach for the proposed application. The proposed intelligent system results are compared with those obtained using conventional techniques including thresholding and clustering based approaches. Experimental and Monte Carlo simulated PET phantom data sets and clinical PET volumes of nonsmall cell lung cancer patients were utilised to validate the proposed algorithm which has demonstrated promising results.

  5. Measurement and modeling of advanced coal conversion processes, Volume II

    Energy Technology Data Exchange (ETDEWEB)

    Solomon, P.R.; Serio, M.A.; Hamblen, D.G. [and others

    1993-06-01

    A two dimensional, steady-state model for describing a variety of reactive and nonreactive flows, including pulverized coal combustion and gasification, is presented. The model, referred to as 93-PCGC-2 is applicable to cylindrical, axi-symmetric systems. Turbulence is accounted for in both the fluid mechanics equations and the combustion scheme. Radiation from gases, walls, and particles is taken into account using a discrete ordinates method. The particle phase is modeled in a lagrangian framework, such that mean paths of particle groups are followed. A new coal-general devolatilization submodel (FG-DVC) with coal swelling and char reactivity submodels has been added.

  6. Wireless sap flow measurement system

    Science.gov (United States)

    Kuo, C.; Davis, T. W.; Tseng, C.; Cheng, C.; Liang, X.; Yu, P.

    2010-12-01

    This study exhibits a measurement system for wireless sensor networks to measure sap flow in multiple locations simultaneously. Transpiration is a major component of the land-surface system because it is indicative of the water movement between the soil and the air. Sap flow can be used to approximate transpiration. In forests, transpiration cannot be represented by the sap flow from a single tree. Multi-location sap flow measurements are required to show the heterogeneity caused by different trees or soil conditions. Traditional multi-location measurements require manpower and capital for data collection and instrument maintenance. Fortunately, multi-location measurements can be achieved by using the new technology of wireless sensor networks. With multi-hop communication protocol, data can be forwarded to the base station via multiple sensor nodes. This communication protocol can provide reliable data collection with the least power consumption. This study encountered two major problems. The first problem was signal amplification. The Crossbow IRIS mote was selected as the sensor node that receives the temperature data of the sap flow probe (thermocouple) through a MDA300 data acquisition board. However, the wireless sensor node could not directly receive any data from the thermocouples since the least significant bit value of the MDA300, 0.6 mV, is much higher than the voltage signal generated. Thus, the signal from the thermocouple must be amplified to exceed this threshold. The second problem is power management. A specific heat differential is required for the thermal dissipation method of measuring sap flow. Thus, an adjustable DC power supply is necessary for calibrating the heater's temperature settings. A circuit was designed to combine the signal amplifier and power regulator. The regulator has been designed to also provide power to the IRIS mote to extend battery life. This design enables wireless sap flow measurements in the forest. With the

  7. Measuring the mode volume of plasmonic nanocavities using coupled optical emitters

    CERN Document Server

    Russell, Kasey J; Hu, Evelyn; 10.1103/PhysRevB.85.245445

    2012-01-01

    Metallic optical systems can confine light to deep sub-wavelength dimensions, but verifying the level of confinement at these length scales typically requires specialized techniques and equipment for probing the near-field of the structure. We experimentally measured the confinement of a metal-based optical cavity by using the cavity modes themselves as a sensitive probe of the cavity characteristics. By perturbing the cavity modes with conformal dielectric layers of sub-nm thickness using atomic layer deposition, we find the exponential decay length of the modes to be less than 5% of the free-space wavelength (\\lambda) and the mode volume to be of order \\lambda^3/1000. These results provide experimental confirmation of the deep sub-wavelength confinement capabilities of metal-based optical cavities.

  8. Simulation of Variable Air Volume System with Different Duct Layout

    Institute of Scientific and Technical Information of China (English)

    CHEN Hua(陈华); TU Guang-bei(涂光备); FRANCIS W H Yik

    2004-01-01

    The duct static pressure reset (DSPR) control method is a popular modern control method widely applied to variable air volume (VAV) systems of commercial buildings. In this paper, a VAV system simulation program was used to predict the system performance and zone air temperature of two kinds of layouts that were applied to a typical floor of an existing building office in Hong Kong. The position where the static pressure sensor was placed should affect the zones temperature and energy consumption. The comparison of predictions of the two kinds of layouts indicates that with the same DSPR control method the layout of the air duct might influence the fan control result and energy savings.

  9. Stochastic measurements and systems implications

    Science.gov (United States)

    Collins, J. L.; Greene, R. R.

    1985-06-01

    The U.S. Navy is defining the baseline performance of the current SSN ASW suite in the Arctic operating environment. This suite includes the AN/BQQ-5 sonar suit (including the Towed Array, the sphere and other sensor and processor sub-systems), communications subsystems and weapon systems (Mk 48 and ADCAP). An effective acoustic measurement program in the Arctic must support the evaluation of how well the different subsystems are able to carry out their assigned functions. Unique aspects of the operating environment in the Arctic include unusual noise properties, unusual transmission effects and an unusual sea surface. This report addresses those acoustic transmission effects which affect system performance due to fluctuations or spreads in the acoustic field space, angle time and frequency.

  10. A new method for the measurement of meteorite bulk volume via ideal gas pycnometry

    Science.gov (United States)

    Li, Shijie; Wang, Shijie; Li, Xiongyao; Li, Yang; Liu, Shen; Coulson, Ian M.

    2012-10-01

    To date, of the many techniques used to measure the bulk volume of meteorites, only three methods (Archimedean bead method, 3-D laser imaging and X-ray microtomography) can be considered as nondestructive or noncontaminating. The bead method can show large, random errors for sample sizes of smaller than 5 cm3. In contrast, 3-D laser imaging is a high-accuracy method even when measuring the bulk volumes of small meteorites. This method is both costly and time consuming, however, and meteorites of a certain shape may lead to some uncertainties in the analysis. The method of X-ray microtomography suffers from the same problems as 3-D laser imaging. This study outlines a new method of high-accuracy, nondestructive and noncontaminating measurement of the bulk volume of meteorite samples. In order to measure the bulk volume of a meteorite, one must measure the total volume of the balloon vacuum packaged meteorite and the volume of balloon that had been used to enclose the meteorite using ideal gas pycnometry. The difference between the two determined volumes is the bulk volume of the meteorite. Through the measurement of zero porosity metal spheres and tempered glass fragments, our results indicate that for a sample which has a volume of between 0.5 and 2 cm3, the relative error of the measurement is less than ±0.6%. Furthermore, this error will be even smaller (less than ±0.1%) if the determined sample size is larger than 2 cm3. The precision of this method shows some volume dependence. For samples smaller than 1 cm3, the standard deviations are less than ±0.328%, and these values will fall to less than ±0.052% for samples larger than 2 cm3. The porosities of nine fragments of Jilin, GaoGuenie, Zaoyang and Zhaodong meteorites have been measured using our vacuum packaging-pycnometry method, with determined average porosities of Jilin, GaoGuenie, Zaoyang and Zhaodong of 9.0307%, 2.9277%, 17.5437% and 5.9748%, respectively. These values agree well with the porosities

  11. Large range rotation distortion measurement for remote sensing images based on volume holographic optical correlator

    Science.gov (United States)

    Zheng, Tianxiang; Cao, Liangcai; Zhao, Tian; He, Qingsheng; Jin, Guofan

    2012-10-01

    Volume holographic optical correlator can compute the correlation results between images at a super-high speed. In the application of remote imaging processing such as scene matching, 6,000 template images have been angularly multiplexed in the photorefractive crystal and the 6,000 parallel processing channels are achieved. In order to detect the correlation pattern of images precisely and distinguishingly, an on-off pixel inverted technology of images is proposed. It can fully use the CCD's linear range for detection and expand the normalized correlation value differences as the target image rotates. Due to the natural characteristics of the remote sensing images, the statistical formulas between the rotation distortions and the correlation results can be estimated. The rotation distortion components can be estimated by curve fitting method with the data of correlation results. The intensities of the correlation spots are related to the distortion between the two images. The rotation distortion could be derived from the intensities in the post processing procedure. With 18 rotations of the input image and sending them into the volume holographic system, the detection of the rotation variation in the range of 180° can be fulfilled. So the large range rotation distortion detection is firstly realized. It offers a fast, large range rotation measurement method for image distortions.

  12. Inter-observer variation in ultrasound measurement of the volume and diameter of thyroid nodules

    Energy Technology Data Exchange (ETDEWEB)

    Choi, Young Jun; Baek, Jung Hwan; Hong, Min Ji; Lee, Jeong Hyun [Dept. of Radiology, and Research Institute of Radiology, Asan Medical Center, University of Ulsan College of Medicine, Seoul (Korea, Republic of)

    2015-06-15

    Thyroid nodule measurement using ultrasonography (US) is widely performed in various clinical scenarios. The purpose of this study was to evaluate inter-observer variation in US measurement of the volume and maximum diameter of thyroid nodules. This retrospective study included 73 consecutive patients with 85 well-defined thyroid nodules greater than 1 cm in their maximum diameter. US examinations were independently performed by using standardized measurement methods, conducted by two clinically experienced thyroid radiologists. The maximum nodule diameter and nodule volume, calculated from nodule diameters using the ellipsoid formula, were obtained by each reader. Inter-observer variations in volume and maximum diameter were determined using 95% Bland-Altman limits of agreement. The degree of inter-observer variations in volumes and the maximum diameters were compared using the Student's t test, between nodules < 2 cm in maximum diameter and those with > or = 2 cm. The mean inter-observer difference in measuring the nodule volume was -1.6%, in terms of percentage of the nodule volume, and the 95% limit of agreement was +/- 13.1%. For maximum nodule diameter, the mean inter-observer difference was -0.6%, in terms of percentage of the nodule diameter, and the 95% limit of agreement was +/- 7.3%. Inter-observer variation in volume was greater in nodules of < 2 cm in maximum diameter, compared to the larger nodules (p = 0.035). However, no statistically significant difference was noted between the two groups regarding maximum nodule diameters (p = 0.511). Any differences smaller than 13.1% and 7.3% in volume and maximum diameter, respectively, measured by using US for well-defined thyroid nodules of > 1 cm should not be considered as a real change in size.

  13. 3D photography is a reliable method of measuring infantile haemangioma volume over time.

    Science.gov (United States)

    Robertson, Sarah A; Kimble, Roy M; Storey, Kristen J; Gee Kee, Emma L; Stockton, Kellie A

    2016-09-01

    Infantile haemangiomas are common lesions of infancy. With the development of novel treatments utilised to accelerate their regression, there is a need for a method of assessing these lesions over time. Volume is an ideal assessment method because of its quantifiable nature. This study investigated whether 3D photography is a valid tool for measuring the volume of infantile haemangiomas over time. Thirteen children with infantile haemangiomas presenting to the Vascular Anomalies Clinic, Royal Children's Hospital/Lady Cilento Children's Hospital treated with propranolol were included in the study. Lesion volume was assessed using 3D photography at presentation, one month and three months follow up. Intrarater reliability was determined by retracing all images several months after the initial mapping. Interrater reliability of the 3D camera software was determined by two investigators, blinded to each other's results, independently assessing infantile haemangioma volume. Lesion volume decreased significantly between presentation and three-month follow-up (p<0.001). Volume intra- and interrater reliability were excellent with ICC 0.991 (95% CI 0.982, 0.995) and 0.978 (95% CI 0.955, 0.989), respectively. This study demonstrates images taken with the 3D LifeViz™ camera and lesion volume calculated with Dermapix® software is a reliable method for assessing infantile haemangioma volume over time. Copyright © 2016 Elsevier Inc. All rights reserved.

  14. Federal Logistics Information System. FLIS Procedures Manual Publications. Volume 15.

    Science.gov (United States)

    1995-01-01

    4,5,7,15 dress Code DEMIL Demilitarization 4,15 DoDAAD Department of De- fense Activity Ad- DESC Defense Electronics 2,14 dress Dictionary Supply Center...Supply 2.14 DoDAAC Department of De- Center fense Activity Ad- dress Code iv CH 2 DoD 4100.39-M Volume 15 Volume(s) Volume(s) DoDAAD Department of De

  15. Hospital procedure volume should not be used as a measure of surgical quality.

    Science.gov (United States)

    LaPar, Damien J; Kron, Irving L; Jones, David R; Stukenborg, George J; Kozower, Benjamin D

    2012-10-01

    The Agency for Healthcare Research and Quality and the Leapfrog Group use hospital procedure volume as a quality measure for pancreatic resection (PR), abdominal aortic aneurysm (AAA) repair, esophageal resection (ER), and coronary artery bypass grafting (CABG). However, controversy exists regarding the strength and validity of the evidence for the volume-outcome association. The purpose of this study was to reevaluate the volume-outcome relationship for these procedures. Discharge data for 261,412 patients were extracted from the 2008 Nationwide Inpatient Sample. The relationship between hospital procedure volume and mortality was rigorously assessed using hierarchical general linear modeling with restricted cubic splines, adjusted for patient demographics, comorbid disease, and elective procedure status. Unadjusted mortality rates were PR (4.7%), AAA (12.7%), ER (5.8%), and CABG (2.2%), and the majority of operations were elective. Hospital procedure volume was not a statistically significant predictor of in-hospital mortality for any of the 4 procedures. Strong predictors of mortality included age, elective procedure status, renal failure, and malnutrition (P procedure volume is not a significant predictor of mortality for the performance of pancreatectomy, AAA repair, esophagectomy, or CABG. Procedure volume by itself should not be used as a proxy measure for surgical quality. Patient mortality risk is primarily attributable to patient-level characteristics such as age and comorbidity.

  16. Measurement of breast volume is a useful supplement to select candidates for surgical breast reduction

    DEFF Research Database (Denmark)

    Ikander, Peder; Drejøe, Jennifer Berg; Lumholt, Pavia

    2014-01-01

    for breast reduction surgery, thus establishing a standard decision basis that can be shared by surgeons and departments to secure patients fair and equal treatment opportunities. MATERIAL AND METHODS: A total of 427 patients who were referred to three Danish public hospitals with breast hypertrophy...... in the period from January 2007 to March 2011 were included prospectively in the study. The patients' subjective complaints, height, weight and standard breast measurements were registered as well as the decision for or against surgery. Breast volume was measured using transparent plastic cups. RESULTS: Cut......-off values for breast volume were calculated based on whether or not the patients were offered reduction surgery. Most patients (93%) with a breast volume below 800 cc were not offered surgery, while most with a volume exceeding 900 cc were offered surgery (94%). In the grey zone between 800 and 900 cc...

  17. Accuracy of cancellous bone volume fraction measured by micro-CT scanning

    DEFF Research Database (Denmark)

    Ding, Ming; Odgaard, A; Hvid, I

    1999-01-01

    Volume fraction, the single most important parameter in describing trabecular microstructure, can easily be calculated from three-dimensional reconstructions of micro-CT images. This study sought to quantify the accuracy of this measurement. One hundred and sixty human cancellous bone specimens...... which covered a large range of volume fraction (9.8-39.8%) were produced. The specimens were micro-CT scanned, and the volume fraction based on Archimedes' principle was determined as a reference. After scanning, all micro-CT data were segmented using individual thresholds determined by the scanner...

  18. LARGE VOLUME IONIZATION CHAMBER USED AS LABORATORY REFERENCE FOR LOW ENERGY X—RAY MEASUREMENT

    Institute of Scientific and Technical Information of China (English)

    杨国山; 薛永库; 等

    1994-01-01

    A large volume spherical ionization chamber of 195mm diameter and 0.36mg/cm2 wall thickness made from conducting carbon-fibre epoxy composite material has been developed.The mechanical intensity of the chamber is satisfactory for a good longterm volume stability.Owing to its large volume and thin wall,the chamber is sensitive to low energy photon beams and has excellent energy-response characteristics.This ionization chamber is suitable not only for a laboratory reference but also for measurement of low energy photon beam exposure rates at protection-level.

  19. Small power systems study. Volume. Study results. Technical summary report

    Energy Technology Data Exchange (ETDEWEB)

    Sitney, L.R.

    1978-05-31

    The Division of Solar Technology of the Department of Energy is currently examining the market potential of a number of dispersed solar energy systems, including the small (less than or equal to 10 MW/sub e/) solar thermal power system. Small fossil-fueled generating units in the United States utility system, (i.e., investor-owned, municipal, and cooperatives) have a current capacity of approximately 8000 MW/sub e/ or about 1.5 percent of the total US electrical capacity, and provide a large potential market for small solar thermal power systems. The Small Power Systems Study has as its objective the determination of conditions under which small (less than or equal to 10 MW/sub e/) solar thermal power units can provide cost-effective electrical power to a variety of users. Potential users, in addition to the utility systems; include Department of Defense installations and applications, remote mining and/or lumbering operations, and other industrial power systems with and without cogeneration. The first year's results on the Small Power Systems Study are summarized. The data base used and the breakeven cost analysis are discussed. Information on both small (less than or equal to 10 MW/sub e/) generating units and the utility systems using them is presented as well as data on fossil fuel costs, solar plant costs, and solar insolation values. The results of a survey of Department of Defense (DOD) worldwide electrical generating capacity at its military bases and on a potential DOD application are presented. Information on a potential small solar power system experiment in the interior of Alaska is given, and a limited amount of information on a remote application which would provide power or a large open pit copper mine is presented. Volume II of this Technical Summary Report contains an inventory, by state, of the small (less than or equal to 10 MW/sub e/) generating units in the US utility system. (WHK)

  20. Shared Communications: Volume 2. In-Depth Systems Research

    Energy Technology Data Exchange (ETDEWEB)

    Truett, LF

    2004-09-22

    This report is the second of two documents that examine the literature for actual examples of organizations and agencies that share communications resources. While the primary emphasis is on rural, intelligent transportation system (ITS) communications involving transit, examples will not be limited to rural activities, nor to ITS implementation, nor even to transit. In addition, the term ''communication'' will be broadly applied to include all information resources. The first document of this series, ''Shared Communications: Volume I. A Summary and Literature Review'', defines the meaning of the term ''shared communication resources'' and provides many examples of agencies that share resources. This document, ''Shared Communications: Volume II. In-Depth Systems Research'', reviews attributes that contributed to successful applications of the sharing communication resources concept. A few examples of each type of communication sharing are provided. Based on the issues and best practice realworld examples, recommendations for potential usage and recommended approaches for field operational tests are provided.

  1. Volume measurement by using super-resolution MRI: application to prostate volumetry

    CERN Document Server

    Oubel, Estanislao; Iannessi, Antoine

    2015-01-01

    Accuracy and precision of measurements are important for patient follow up in oncology but, unfortunately, partial volume effects introduce an undesired variability between observers. Super resolution techniques (SR) combine multiple acquisitions of an object into a single image richer in details. Herein, the use of SR for reducing variability is investigated in the specific context of prostate measurements. Prostate is typically imaged by T2-weighted MRI in three perpendicular low resolution images, each of them presenting partial volume effects in the direction of the slice selection gradient. SR techniques allow to combine these images into an image presenting the same level of details in all directions. This is expected to increase the accuracy and reproducibility of volume measurements, which in turn improves other derived measurements like PSA density.

  2. Data collection system. Volume 1, Overview and operators manual; Volume 2, Maintenance manual; Appendices

    Energy Technology Data Exchange (ETDEWEB)

    Caudell, R.B.; Bauder, M.E.; Boyer, W.B.; French, R.E.; Isidoro, R.J.; Kaestner, P.C.; Perkins, W.G.

    1993-09-01

    Sandia National Laboratories (SNL) Instrumentation Development Department was tasked by the Defense Nuclear Agency (DNA) to record data on Tektronix RTD720 Digitizers on the HUNTERS TROPHY field test conducted at the Nevada Test Site (NTS) on September 18, 1992. This report contains a overview and description of the computer hardware and software that was used to acquire, reduce, and display the data. The document is divided into two volumes: an overview and operators manual (Volume 1) and a maintenance manual (Volume 2).

  3. Coal gasification systems engineering and analysis. Volume 1: Executive summary

    Science.gov (United States)

    1980-01-01

    Feasibility analyses and systems engineering studies for a 20,000 tons per day medium Btu (MBG) coal gasification plant to be built by TVA in Northern Alabama were conducted. Major objectives were as follows: (1) provide design and cost data to support the selection of a gasifier technology and other major plant design parameters, (2) provide design and cost data to support alternate product evaluation, (3) prepare a technology development plan to address areas of high technical risk, and (4) develop schedules, PERT charts, and a work breakdown structure to aid in preliminary project planning. Volume one contains a summary of gasification system characterizations. Five gasification technologies were selected for evaluation: Koppers-Totzek, Texaco, Lurgi Dry Ash, Slagging Lurgi, and Babcock and Wilcox. A summary of the trade studies and cost sensitivity analysis is included.

  4. Measuring air layer volumes retained by submerged floating-ferns Salvinia and biomimetic superhydrophobic surfaces

    Directory of Open Access Journals (Sweden)

    Matthias J. Mayser

    2014-06-01

    Full Text Available Some plants and animals feature superhydrophobic surfaces capable of retaining a layer of air when submerged under water. Long-term air retaining surfaces (Salvinia-effect are of high interest for biomimetic applications like drag reduction in ship coatings of up to 30%. Here we present a novel method for measuring air volumes and air loss under water. We recorded the buoyancy force of the air layer on leaf surfaces of four different Salvinia species and on one biomimetic surface using a highly sensitive custom made strain gauge force transducer setup. The volume of air held by a surface was quantified by comparing the buoyancy force of the specimen with and then without an air layer. Air volumes retained by the Salvinia-surfaces ranged between 0.15 and 1 L/m2 depending on differences in surface architecture. We verified the precision of the method by comparing the measured air volumes with theoretical volume calculations and could find a good agreement between both values. In this context we present techniques to calculate air volumes on surfaces with complex microstructures. The introduced method also allows to measure decrease or increase of air layers with high accuracy in real-time to understand dynamic processes.

  5. Three-dimensional measurement of bubble volume based on dual perspective imaging

    Science.gov (United States)

    Xue, Ting; Zhang, Shao-jie; Wu, Bin

    2017-01-01

    This paper presents a new three-dimensional (3D) volume measurement approach of bubble in gas-liquid two-phase flow. According to the dual perspective imaging principle, bubble feature images can be captured from two different view angles. The least square ellipse fitting algorithm is used to figure out the feature parameters from the captured images. Then the 3D volume of bubble can be quantitatively measured. Compaerd with the traditional volume estimation methods based on single perspective imaging, it can effectively reduce the loss of bubble feature information. In the experiment, the 3D volume reconstruction of bubbles from dual perspective images is conducted, and the variation of bubble volume in the bubble rising process is studied. The results show that the measurement accuracy based on the proposed 3D method is higher than those based on traditional methods. The volume of rising bubble is periodically changed, which indicates that bubble achieves periodic rotation and deformation in the rising process.

  6. Spatial Visualization Tasks To Support Students’ Spatial Structuring In Learning Volume Measurement

    Directory of Open Access Journals (Sweden)

    Shintia Revina

    2011-07-01

    Full Text Available Many prior researches found that most of students in grade five tended to have difficulty in fully grasping the concept of volume measurement because they have to build their competence in spatial structuring. The unit of volume “packing” measurement must be integrated and coordinated in three-dimension. On the other hand, it is revealed the errors that students made on the volume measurement tasks with threedimensional cube arrays are related to some aspects of spatial visualization, such as the skill to "read off" two-dimensional representation of solid objects. For those reasons, this research is aimed to develop classroom activities with the use of spatial visualization tasks to support students’ spatial structuring in learning volume measurement. Consequently, design research was chosen as an appropriate means to achieve this research goal. In this research, a sequence of instructional activities is designed and developed based on the hypothesis of students’ learning processes. This research was conducted in grade 5 of SD Pupuk Sriwijaya Palembang, Indonesia.Keywords: volume measurement, spatial structuring, spatial visualization, design research. DOI: http://dx.doi.org/10.22342/jme.2.2.745.127-146

  7. Deep Drilling Basic Research: Volume 5 - System Evaluations. Final Report, November 1988--August 1990

    Energy Technology Data Exchange (ETDEWEB)

    None

    1990-06-01

    This project is aimed at decreasing the costs and increasing the efficiency of drilling gas wells in excess of 15,000 feet. This volume presents a summary of an evaluation of various drilling techniques. Drilling solutions were compared quantitatively against typical penetration rates derived from conventional systems. A qualitative analysis measured the impact of a proposed system on the drilling industry. The evaluations determined that the best candidates f o r improving the speed and efficiency of drilling deep gas wells include: PDC/TSD bits, slim-hole drilling, roller-cone bits, downhole motors, top-driven systems, and coiled-tubing drilling.

  8. Location studies of prostate volume measurement by using transrectal ultrasonography: Experimental study by self-produced prostate phantom

    Energy Technology Data Exchange (ETDEWEB)

    Yoon, Joon; Byeon, Il Kyun; Lee, Hoo Min [Dept. of Radiological Science, (Korea, Republic of); Kim, Yun Min; Kim, Hyeong Gyun [Dept. of Radiological Technology, Dongnam Health University, Suwon (Korea, Republic of)

    2015-12-15

    Accurate volume measurement of the prostate is a significant role in determining the result of diagnosis and treatment of benign prostate hyperplasia. The purpose of this study was to determine, when measuring prostate volume by TRUS, whether location is more accurately determined by transaxial or longitudinal scanning. With reference to the patient’s image, it was produced six prostate model. It compares the actual volume and the measurement volume, and find the optimal measurement position of each specific model. Prostate volume measured by TRUS closely correlates with prostate phantom volume. There was no significant difference(p = .156). To measure the accurate volume of prostate with focal protrusion, its length should be measured exclude the protrusions.

  9. Calibration system for measuring the radon flux density.

    Science.gov (United States)

    Onishchenko, A; Zhukovsky, M; Bastrikov, V

    2015-06-01

    The measurement of radon flux from soil surface is the useful tool for the assessment of radon-prone areas and monitoring of radon releases from uranium mining and milling residues. The accumulation chambers with hollow headspace and chambers with activated charcoal are the most used devices for these purposes. Systematic errors of the measurements strongly depend on the geometry of the chamber and diffusion coefficient of the radon in soil. The calibration system for the attestation of devices for radon flux measurements was constructed. The calibration measurements of accumulation chambers and chambers with activated charcoal were conducted. The good agreement between the results of 2D modelling of radon flux and measurements results was observed. It was demonstrated that reliable measurements of radon flux can be obtained by chambers with activated charcoal (equivalent volume ~75 l) or by accumulation chambers with hollow headspace of ~7-10 l and volume/surface ratio (height) of >15 cm.

  10. High-Temperature-High-Volume Lifting for Enhanced Geothermal Systems

    Energy Technology Data Exchange (ETDEWEB)

    Turnquist, Norman [GE Global Research, Munchen (Germany); Qi, Xuele [GE Global Research, Munchen (Germany); Raminosoa, Tsarafidy [GE Global Research, Munchen (Germany); Salas, Ken [GE Global Research, Munchen (Germany); Samudrala, Omprakash [GE Global Research, Munchen (Germany); Shah, Manoj [GE Global Research, Munchen (Germany); Van Dam, Jeremy [GE Global Research, Munchen (Germany); Yin, Weijun [GE Global Research, Munchen (Germany); Zia, Jalal [GE Global Research, Munchen (Germany)

    2013-12-20

    This report summarizes the progress made during the April 01, 2010 – December 30, 2013 period under Cooperative Agreement DE-EE0002752 for the U.S. Department of Energy entitled “High-Temperature-High-Volume Lifting for Enhanced Geothermal Systems.” The overall objective of this program is to advance the technology for well fluids lifting systems to meet the foreseeable pressure, temperature, and longevity needs of the Enhanced Geothermal Systems (EGS) industry for the coming ten years. In this program, lifting system requirements for EGS wells were established via consultation with industry experts and site visits. A number of artificial lift technologies were evaluated with regard to their applicability to EGS applications; it was determined that a system based on electric submersible pump (ESP) technology was best suited to EGS. Technical barriers were identified and a component-level technology development program was undertaken to address each barrier, with the most challenging being the development of a power-dense, small diameter motor that can operate reliably in a 300°C environment for up to three years. Some of the targeted individual component technologies include permanent magnet motor construction, high-temperature insulation, dielectrics, bearings, seals, thrust washers, and pump impellers/diffusers. Advances were also made in thermal management of electric motors. In addition to the overall system design for a full-scale EGS application, a subscale prototype was designed and fabricated. Like the full-scale design, the subscale prototype features a novel “flow-through-the-bore” permanent magnet electric motor that combines the use of high temperature materials with an internal cooling scheme that limits peak internal temperatures to <330°C. While the full-scale high-volume multi-stage pump is designed to lift up to 80 kg/s of process water, the subscale prototype is based on a production design that can pump 20 kg/s and has been modified

  11. Comparison between CT volume measurement and histopathological assessment of response to neoadjuvant therapy in rectal cancer

    Energy Technology Data Exchange (ETDEWEB)

    Pomerri, Fabio, E-mail: fabio.pomerri@unipd.it [Veneto Institute of Oncology IOV-IRCCS, via Gattamelata 64, 35128 Padua (Italy); Department of Medicine, University of Padua, via Giustiniani 2, 35128 Padua (Italy); Pucciarelli, Salvatore, E-mail: puc@unipd.it [Department of Oncological and Surgical Sciences, University of Padua, via Giustiniani 2, 35128 Padua (Italy); Gennaro, Gisella, E-mail: gisella.gennaro@pd.infn.it [Veneto Institute of Oncology IOV-IRCCS, via Gattamelata 64, 35128 Padua (Italy); Maretto, Isacco, E-mail: isac77@gmail.com [Veneto Institute of Oncology IOV-IRCCS, via Gattamelata 64, 35128 Padua (Italy); Nitti, Donato, E-mail: donato.nitti@unipd.it [Department of Oncological and Surgical Sciences, University of Padua, via Giustiniani 2, 35128 Padua (Italy); Muzzio, Pier Carlo, E-mail: pcmuzzio@unipd.it [Veneto Institute of Oncology IOV-IRCCS, via Gattamelata 64, 35128 Padua (Italy)

    2012-12-15

    Objectives: The aim of this study was to compare volume measurements on computed tomography (CT) images with histopathological assessments of chemoradiotherapy (CRT)-induced tumor regression in locally advanced rectal cancer (RC). Methods: In 25 patients (13 males, 12 females; median age, 63 years; age range, 44–79 years) with locally advanced RC treated with preoperative CRT and surgery, two radiologists measured tumor volume on CT images before and after CRT. CT-based tumor volumetry and the modified response evaluation criteria in solid tumors (mRECISTs) were compared with T and N downstaging after CRT, and with the tumor regression grade (TRG). Results: Tumor volumes were significantly smaller on CT images after CRT. The tumors regressed in 52% (13/25), 36% (9/25) and 40% (10/25) of patients, based on T downstaging, TRG and mRECIST findings, respectively. In terms of T downstaging, the pre- and post-CRT tumor volumes of responders and non-responders to the treatment differed statistically, while their tumor volume reduction rates and volume reductions according to the 65% mRECIST threshold did not. In terms of N downstaging and TRG, the differences between the responders’ and the non-responders’ pre- and post-CRT tumor volumes, tumor volume reduction rates, and mRECIST thresholds were never statistically significant. Conclusion: Measuring tumor size on CT images is of limited value in predicting the histopathological response to preoperative CRT in RC patients, so it may be unwise to select surgical treatment strategies based on CT volumetry.

  12. Effect of malaria on placental volume measured using three-dimensional ultrasound: a pilot study

    Directory of Open Access Journals (Sweden)

    Rijken Marcus J

    2012-01-01

    Full Text Available Abstract Background The presence of malaria parasites and histopathological changes in the placenta are associated with a reduction in birth weight, principally due to intrauterine growth restriction. The aim of this study was to examine the feasibility of studying early pregnancy placental volumes using three-dimensional (3D ultrasound in a malaria endemic area, as a small volume in the second trimester may be an indicator of intra-uterine growth restriction and placental insufficiency. Methods Placenta volumes were acquired using a portable ultrasound machine and a 3D ultrasound transducer and estimated using the Virtual Organ Computer-aided AnaLysis (VOCAL image analysis software package. Intra-observer reliability and limits of agreement of the placenta volume measurements were calculated. Polynomial regression models for the mean and standard deviation as a function of gestational age for the placental volumes of uninfected women were created and tested. Based on these equations each measurement was converted into a z -score. The z-scores of the placental volumes of malaria infected and uninfected women were then compared. Results Eighty-four women (uninfected = 65; infected = 19 with a posterior placenta delivered congenitally normal, live born, single babies. The mean placental volumes in the uninfected women were modeled to fit 5th, 10th, 50th, 90th and 95th centiles for 14-24 weeks' gestation. Most placenta volumes in the infected women were below the 50th centile for gestational age; most of those with Plasmodium falciparum were below the 10th centile. The 95% intra-observer limits of agreement for first and second measurements were ± 37.0 mL and ± 25.4 mL at 30 degrees and 15 degrees rotation respectively. Conclusion The new technique of 3D ultrasound volumetry of the placenta may be useful to improve our understanding of the pathophysiological constraints on foetal growth caused by malaria infection in early pregnancy.

  13. MRI markers for mild cognitive impairment: comparisons between white matter integrity and gray matter volume measurements.

    Directory of Open Access Journals (Sweden)

    Yu Zhang

    Full Text Available The aim of the study was to evaluate the value of assessing white matter integrity using diffusion tensor imaging (DTI for classification of mild cognitive impairment (MCI and prediction of cognitive impairments in comparison to brain atrophy measurements using structural MRI. Fifty-one patients with MCI and 66 cognitive normal controls (CN underwent DTI and T1-weighted structural MRI. DTI measures included fractional anisotropy (FA and radial diffusivity (DR from 20 predetermined regions-of-interest (ROIs in the commissural, limbic and association tracts, which are thought to be involved in Alzheimer's disease; measures of regional gray matter (GM volume included 21 ROIs in medial temporal lobe, parietal cortex, and subcortical regions. Significant group differences between MCI and CN were detected by each MRI modality: In particular, reduced FA was found in splenium, left isthmus cingulum and fornix; increased DR was found in splenium, left isthmus cingulum and bilateral uncinate fasciculi; reduced GM volume was found in bilateral hippocampi, left entorhinal cortex, right amygdala and bilateral thalamus; and thinner cortex was found in the left entorhinal cortex. Group classifications based on FA or DR was significant and better than classifications based on GM volume. Using either DR or FA together with GM volume improved classification accuracy. Furthermore, all three measures, FA, DR and GM volume were similarly accurate in predicting cognitive performance in MCI patients. Taken together, the results imply that DTI measures are as accurate as measures of GM volume in detecting brain alterations that are associated with cognitive impairment. Furthermore, a combination of DTI and structural MRI measurements improves classification accuracy.

  14. Efficient Traducer Tracing System Using Traffic Volume Information

    Directory of Open Access Journals (Sweden)

    K.V.Ramana

    2011-08-01

    Full Text Available Many leading Broadband access technologies and their accessing abilities have the capability to meet the future requirements of the Broadband consumer. With the enormous growth in the broadband technologies, there is a need of applying simmering technology in many applications like video conference systems and content transmission systems. Streaming content enables users to get access the files quickly and not have to wait until the file is done downloading. Security remains one of the main challenges for Content Streaming. Digital Rights Management (DRM system must be implemented to avoid content spreading and un-intentional content usage. Water marking technology can also be used to implement the DRM system but it has its own limitations and attacks. A control method for the steaming content delivery is required to prevent abuse of the content. For this reason, authors have proposed a contended methodology that uses traffic volume information obtained from routers. Traducer tracing is one of the essential technologies that designs DRM systems, and empowers content distributors to notice and control content acquisition. This technology utilizes the main concept of traffic contours that helps to determine who is watching the streaming content and whether or not a secondary content delivery exists i.e., mainly used to determine whether the network is being traced out by the intruder or not.

  15. Precise quantification of dialysis using continuous sampling of spent dialysate and total dialysate volume measurement.

    Science.gov (United States)

    Argilés, A; Ficheux, A; Thomas, M; Bosc, J Y; Kerr, P G; Lorho, R; Flavier, J L; Stec, F; Adelé, C; Leblanc, M; Garred, L J; Canaud, B; Mion, H; Mion, C M

    1997-08-01

    The "gold standard" method to evaluate the mass balances achieved during dialysis for a given solute remains total dialysate collection (TDC). However, since handling over 100 liter volumes is unfeasible in our current dialysis units, alternative methods have been proposed, including urea kinetic modeling, partial dialysate collection (PDC) and more recently, monitoring of dialysate urea by on-line devices. Concerned by the complexity and costs generated by these devices, we aimed to adapt the simple "gold standard" TDC method to clinical practice by diminishing the total volumes to be handled. We describe a new system based on partial dialysate collection, the continuous spent sampling of dialysate (CSSD), and present its technical validation. Further, and for the first time, we report a long-term assessment of dialysis dosage in a dialysis clinic using both the classical PDC and the new CSSD system in a group of six stable dialysis patients who were followed for a period of three years. For the CSSD technique, spent dialysate was continuously sampled by a reversed automatic infusion pump at a rate of 10 ml/hr. The piston was automatically driven by the dialysis machine: switched on when dialysis started, off when dialysis terminated and held during the by pass periods. At the same time the number of production cycles of dialysate was monitored and the total volume of dialysate was calculated by multiplying the volume of the production chamber by the number of cycles. Urea and creatinine concentrations were measured in the syringe and the masses were obtained by multiplying this concentration by the total volume. CSSD and TDC were simultaneously performed in 20 dialysis sessions. The total mass of urea removed was calculated as 58038 and 60442 mmol/session (CSSD and TDC respectively; 3.1 +/- 1.2% variation; r = 0.99; y = 0.92x -28.9; P urea removal: 510 +/- 59 during the first year with PDC and 516 +/- 46 mmol/dialysis session during the third year, using CSSD

  16. Comparative analysis of two methods for measuring sales volumes during malaria medicine outlet surveys.

    Science.gov (United States)

    Patouillard, Edith; Kleinschmidt, Immo; Hanson, Kara; Pok, Sochea; Palafox, Benjamin; Tougher, Sarah; O'Connell, Kate; Goodman, Catherine

    2013-09-05

    There is increased interest in using commercial providers for improving access to quality malaria treatment. Understanding their current role is an essential first step, notably in terms of the volume of diagnostics and anti-malarials they sell. Sales volume data can be used to measure the importance of different provider and product types, frequency of parasitological diagnosis and impact of interventions. Several methods for measuring sales volumes are available, yet all have methodological challenges and evidence is lacking on the comparability of different methods. Using sales volume data on anti-malarials and rapid diagnostic tests (RDTs) for malaria collected through provider recall (RC) and retail audits (RA), this study measures the degree of agreement between the two methods at wholesale and retail commercial providers in Cambodia following the Bland-Altman approach. Relative strengths and weaknesses of the methods were also investigated through qualitative research with fieldworkers. A total of 67 wholesalers and 107 retailers were sampled. Wholesale sales volumes were estimated through both methods for 62 anti-malarials and 23 RDTs and retail volumes for 113 anti-malarials and 33 RDTs. At wholesale outlets, RA estimates for anti-malarial sales were on average higher than RC estimates (mean difference of four adult equivalent treatment doses (95% CI 0.6-7.2)), equivalent to 30% of mean sales volumes. For RDTs at wholesalers, the between-method mean difference was not statistically significant (one test, 95% CI -6.0-4.0). At retail outlets, between-method differences for both anti-malarials and RDTs increased with larger volumes being measured, so mean differences were not a meaningful measure of agreement between the methods. Qualitative research revealed that in Cambodia where sales volumes are small, RC had key advantages: providers were perceived to remember more easily their sales volumes and find RC less invasive; fieldworkers found it more

  17. GEANT4 simulation of water volume fraction measurement in dehydrated crude oil

    Institute of Scientific and Technical Information of China (English)

    JING Chunguo; XING Guangzhong; LIU Bin

    2007-01-01

    Online measurement of water volume fraction (WVF) in dehydrated crude oil is a difficult task due to very little water in dehydrated crude oil and high precision requirements. We presents a method to measure water volume fraction in dehydrated crude oil with γ-ray densitometry. The Monte Carlo computer simulation packet GEANT4 was used to analyze the WVF measuring sensitivity of the γ-ray densitometry at different γ-ray energies, and effects of temperature, pressure, salinity and oil components on WVF measurement. The results show that the γ-ray densitome-try has high sensitivity in γ-ray energy ranges of 16~25 keV, and it can distinguish WVF changes of 0.0005. The calculated WVF decreases about 0.0002 with 1 ℃ of temperature increase and they have approximately linear relation with temperature when water volume fraction remains the same. Effects of pressure, salinity and oil components on water volume fraction can be neglected. Experiments were done to analyze sensitivity of the γ-ray densitometry. The results, as compared with simulations, demonstrate that simulation method is reliable and it is feasible to gauge low water volume fraction using low energy γ-rays.

  18. Image Data Processing System (IDAPS) user manual, S-056 experiment. Volume 1: System description. Volume 2: Batch IDAPS. Volume 3: Interactive IDAPS

    Science.gov (United States)

    1975-01-01

    Image data processing system (IDAPS) developed to satisfy the image processing requirements of the Skylab S-056 experiment is described. The S-056 experiment was designed to obtain high-resolution photographs of the sun in the far ultraviolet, or soft X-ray, portion of the electromagnetic spectrum. Thirty-five thousand photographs were obtained by the three flights of the program; and, faced with such a massive volume of imagery, the designers of the experiment decided to develop a computer-based system which would reduce the image processing workload. The purpose of the IDAPS User Manual is to give the IDAPS user the necessary information and instructions to effectively utilize the system.

  19. Measurement of testicular volume in smaller testes: how accurate is the conventional orchidometer?

    Science.gov (United States)

    Lin, Chih-Chieh; Huang, William J S; Chen, Kuang-Kuo

    2009-01-01

    The aim of this study was to evaluate the accuracy of different methods, including the Seager orchidometer (SO) and ultrasonography (US), for assessing testicular volume of smaller testes (testes volume less than 18 mL). Moreover, the equations used for the calculations--the Hansen formula (length [L] x width [W](2) x 0.52, equation A), the prolate ellipsoid formula (L x W x height [H] x 0.52, equation B), and the Lambert equation (L x W x H x 0.71, equation C)--were also examined and compared with the gold standard testicular volume obtained by water displacement (Archimedes principle). In this study, 30 testes from 15 men, mean age 75.3 (+/-8.3) years, were included. They all had advanced prostate cancer and were admitted for orchiectomy. Before the procedure, all the testes were assessed using SO and US. The dimensions were then input into each equation to obtain the volume estimates. The testicular volume by water displacement was 8.1 +/- 3.5 mL. Correlation coefficients (R(2)) of the 2 different methods (SO, US) to the gold standard were 0.70 and 0.85, respectively. The calculated testicular volumes were 9.2 +/- 3.9 mL (measured by SO, equation A), 11.9 +/- 5.2 mL (measured by SO, equation C), 7.3 +/- 4.2 mL (measured by US, equation A), 6.5 +/- 3.3 mL (measured by US, equation B) and 8.9 +/- 4.5 mL (measured by US, equation C). Only the mean size measured by US and volume calculated with the Hansen equation (equation A) and the mean size measured by US and volume calculated with the Lambert equation (equation C) showed no significant differences when compared with the volumes estimated by water displacement (mean difference 0.81 mL, P = .053, and 0.81 mL, P = .056, respectively). Based on our measurements, we categorized testicular volume by different cutoff values (7.0 mL, 7.5 mL, 8.0 mL, and 8.5 mL) to calculate a new constant for use in the Hansen equation. The new constant was 0.59. We then reexamined the equations using the new 0.59 constant, and found

  20. Revisiting the returns-volume relationship: Time variation, alternative measures and the financial crisis

    Science.gov (United States)

    Cook, Steve; Watson, Duncan

    2017-03-01

    Following its introduction in the seminal study of Osborne (1959), a voluminous literature has emerged examining the returns-volume relationship for financial assets. The present paper revisits this relationship in an examination of the FTSE100 which extends the existing literature in two ways. First, alternative daily measures of the FTSE100 index are used to create differing returns and absolute returns series to employ in an examination of returns-volume causality. Second, rolling regression analysis is utilised to explore potential time variation in the returns-volume relationship. The findings obtained depict a hitherto unconsidered complexity in this relationship with the type of returns series considered and financial crisis found to be significant underlying factors. The implications of the newly derived results for both the understanding of the nature of the returns-volume relationship and the development of theories in connection to it are discussed.

  1. Corneal Volume Measurements with Pentacam for Detection of Keratoconus and Subclinical Keratoconus

    OpenAIRE

    Nurullah Çağıl; Nagihan Uğurlu; Hasan Basri Çakmak; Sucattin İlker Kocamış; Hüseyin Simavlı; Şaban Şimşek

    2013-01-01

    Pur po se: To estimate the sensitivity and specificity of corneal volume (CV) measurements in discriminating keratoconus and subclinical keratoconus from normal corneas. Ma te ri al and Met hod: Clinical records and Pentacam measurements of ninety-four patients with keratoconus, 36 patients with subclinical keratoconus, and 166 refractive surgery candidates with normal corneas were evaluated retrospectively. CV within 3, 5, 7, and 10 mm circles around the central cornea was measur...

  2. A Novel Technology for Measurements of Dielectric Properties of Extremely Small Volumes of Liquids

    Directory of Open Access Journals (Sweden)

    Wei-Na Liu

    2016-01-01

    Full Text Available A high sensitivity sensor for measurement radio frequency (RF dielectric permittivity of liquids is described. Interference is used and parasitic effects are cancellation, which makes the sensor can catch weak signals caused by liquids with extremely small volumes. In addition, we present the relationship between transmission coefficient and permittivity of liquids under test (LUT. Using this sensor, quantitative measurements of the dielectric properties at 5.8 GHz are demonstrated of LUTs. Experiments show that the proposed method only requires the volume of 160 nanoliters for liquids. Therefore, the technology can be used for RF spectroscopic analysis of biological samples and extremely precious liquids.

  3. Guidelines for the verification and validation of expert system software and conventional software: Bibliography. Volume 8

    Energy Technology Data Exchange (ETDEWEB)

    Miller, L.A.; Hayes, J.E.; Mirsky, S.M. [Science Applications International Corp., McLean, VA (United States)

    1995-03-01

    This volume contains all of the technical references found in Volumes 1-7 concerning the development of guidelines for the verification and validation of expert systems, knowledge-based systems, other AI systems, object-oriented systems, and conventional systems.

  4. A dynamical system of deposit and loan volumes based on the Lotka-Volterra model

    Science.gov (United States)

    Sumarti, N.; Nurfitriyana, R.; Nurwenda, W.

    2014-02-01

    In this research, we proposed a dynamical system of deposit and loan volumes of a bank using a predator-prey paradigm, where the predator is loan volumes, and the prey is deposit volumes. The existence of loan depends on the existence of deposit because the bank will allocate the loan volume from a portion of the deposit volume. The dynamical systems have been constructed are a simple model, a model with Michaelis-Menten Response and a model with the Reserve Requirement. Equilibria of the systems are analysed whether they are stable or unstable based on their linearised system.

  5. Analysis of automated highway system risks and uncertainties. Volume 5

    Energy Technology Data Exchange (ETDEWEB)

    Sicherman, A.

    1994-10-01

    This volume describes a risk analysis performed to help identify important Automated Highway System (AHS) deployment uncertainties and quantify their effect on costs and benefits for a range of AHS deployment scenarios. The analysis identified a suite of key factors affecting vehicle and roadway costs, capacities and market penetrations for alternative AHS deployment scenarios. A systematic protocol was utilized for obtaining expert judgments of key factor uncertainties in the form of subjective probability percentile assessments. Based on these assessments, probability distributions on vehicle and roadway costs, capacity and market penetration were developed for the different scenarios. The cost/benefit risk methodology and analysis provide insights by showing how uncertainties in key factors translate into uncertainties in summary cost/benefit indices.

  6. Integrating model of the Project Independence Evaluation System. Volume 1. Executive summary

    Energy Technology Data Exchange (ETDEWEB)

    Shaw, M.L.; Hutzler, M.J.

    1979-04-01

    This report is Volume I of a six-volume series documenting the Integrating Model of the Project Independence Evaluation System (PIES) as it existed on January 1, 1978. It offers a review of entire PIES system, including the basic components of the Integrating Model, which are described in detail in Volume IV of this series. In particular, this volume addresses the problem that PIES solves and the major features and applications of PIES.

  7. Interdependence of the volume and stress ensembles and equipartition in statistical mechanics of granular systems.

    Science.gov (United States)

    Blumenfeld, Raphael; Jordan, Joe F; Edwards, Sam F

    2012-12-07

    We discuss the statistical mechanics of granular matter and derive several significant results. First, we show that, contrary to common belief, the volume and stress ensembles are interdependent, necessitating the use of both. We use the combined ensemble to calculate explicitly expectation values of structural and stress-related quantities for two-dimensional systems. We thence demonstrate that structural properties may depend on the angoricity tensor and that stress-based quantities may depend on the compactivity. This calls into question previous statistical mechanical analyses of static granular systems and related derivations of expectation values. Second, we establish the existence of an intriguing equipartition principle-the total volume is shared equally amongst both structural and stress-related degrees of freedom. Third, we derive an expression for the compactivity that makes it possible to quantify it from macroscopic measurements.

  8. Quantitative radiology: automated measurement of polyp volume in computed tomography colonography using Hessian matrix-based shape extraction and volume growing

    Science.gov (United States)

    Epstein, Mark L.; Obara, Piotr R.; Chen, Yisong; Liu, Junchi; Zarshenas, Amin; Makkinejad, Nazanin; Dachman, Abraham H.

    2015-01-01

    Background Current measurement of the single longest dimension of a polyp is subjective and has variations among radiologists. Our purpose was to develop a computerized measurement of polyp volume in computed tomography colonography (CTC). Methods We developed a 3D automated scheme for measuring polyp volume at CTC. Our scheme consisted of segmentation of colon wall to confine polyp segmentation to the colon wall, extraction of a highly polyp-like seed region based on the Hessian matrix, a 3D volume growing technique under the minimum surface expansion criterion for segmentation of polyps, and sub-voxel refinement and surface smoothing for obtaining a smooth polyp surface. Our database consisted of 30 polyp views (15 polyps) in CTC scans from 13 patients. Each patient was scanned in the supine and prone positions. Polyp sizes measured in optical colonoscopy (OC) ranged from 6-18 mm with a mean of 10 mm. A radiologist outlined polyps in each slice and calculated volumes by summation of volumes in each slice. The measurement study was repeated 3 times at least 1 week apart for minimizing a memory effect bias. We used the mean volume of the three studies as “gold standard”. Results Our measurement scheme yielded a mean polyp volume of 0.38 cc (range, 0.15-1.24 cc), whereas a mean “gold standard” manual volume was 0.40 cc (range, 0.15-1.08 cc). The “gold-standard” manual and computer volumetric reached excellent agreement (intra-class correlation coefficient =0.80), with no statistically significant difference [P (F≤f) =0.42]. Conclusions We developed an automated scheme for measuring polyp volume at CTC based on Hessian matrix-based shape extraction and volume growing. Polyp volumes obtained by our automated scheme agreed excellently with “gold standard” manual volumes. Our fully automated scheme can efficiently provide accurate polyp volumes for radiologists; thus, it would help radiologists improve the accuracy and efficiency of polyp volume

  9. Nuclear Engine System Simulation (NESS). Volume 1: Program user's guide

    Science.gov (United States)

    Pelaccio, Dennis G.; Scheil, Christine M.; Petrosky, Lyman J.

    1993-03-01

    example problem, and compares the results to related NTP engine system designs. Initial installation instructions and program disks are in Volume 2 of the NESS Program User's Guide.

  10. Nuclear Engine System Simulation (NESS). Volume 1: Program user's guide

    Science.gov (United States)

    Pelaccio, Dennis G.; Scheil, Christine M.; Petrosky, Lyman J.

    1993-01-01

    example problem, and compares the results to related NTP engine system designs. Initial installation instructions and program disks are in Volume 2 of the NESS Program User's Guide.

  11. AFM-porosimetry: density and pore volume measurements of particulate materials.

    Science.gov (United States)

    Sörensen, Malin H; Valle-Delgado, Juan J; Corkery, Robert W; Rutland, Mark W; Alberius, Peter C

    2008-06-01

    We introduced the novel technique of AFM-porosimetry and applied it to measure the total pore volume of porous particles with a spherical geometry. The methodology is based on using an atomic force microscope as a balance to measure masses of individual particles. Several particles within the same batch were measured, and by plotting particle mass versus particle volume, the bulk density of the sample can be extracted from the slope of the linear fit. The pore volume is then calculated from the densities of the bulk and matrix materials, respectively. In contrast to nitrogen sorption and mercury porosimetry, this method is capable of measuring the total pore volume regardless of pore size distribution and pore connectivity. In this study, three porous samples were investigated by AFM-porosimetry: one ordered mesoporous sample and two disordered foam structures. All samples were based on a matrix of amorphous silica templated by a block copolymer, Pluronic F127, swollen to various degrees with poly(propylene glycol). In addition, the density of silica spheres without a template was measured by two independent techniques: AFM and the Archimedes principle.

  12. Relations between various measures of iodine intake and thyroid volume, thyroid nodularity, and serum thyroglobulin

    DEFF Research Database (Denmark)

    Rasmussen, Lone Banke; Ovesen, L.; Bulow, I.

    2002-01-01

    plus supplements, iodine intake from diet/kg body wt, and milk intake (P = 0.001 for all), but not urinary iodine excretion measured as a concentration (P = 0.40). All measures of iodine intake were significantly related to serum thyroglobulin concentration (P less than or equal to 0.002), but only...... excretion measured as a urinary concentration, predicted thyroid volume. Serum thyroglobulin concentration appears to be a good marker of iodine status. Subgroups with low intakes of milk and milk products had an increased risk of thyroid disease.......Background: Iodine intake can be measured in various ways, and each method may have advantages and disadvantages. Objective: We sought to investigate the potential associations of various measures of iodine intake with thyroid volume, prevalence of thyroid nodules, and serum thyroglobulin. We also...

  13. Water volume estimates of the Greenland Perennial Firn Aquifer from in situ measurements

    Science.gov (United States)

    Koenig, L.; Miege, C.; Forster, R. R.; Brucker, L.

    2013-12-01

    Improving our understanding of the complex Greenland hydrologic system is necessary for assessing change across the Greenland Ice Sheet and its contribution to sea level rise (SLR). A new component of the Greenland hydrologic system, a Perennial Firn Aquifer (PFA), was recently discovered in April 2011. The PFA represents a large storage of liquid water within the Greenland Ice Sheet with an area of 70,000 × 10,000 km2 simulated by the RACMO2/GR regional climate model which closely follows airborne radar-derived mapping (Forster et al., in press). The average top surface depth of the PFA as detected by radar is 23 m. In April 2013, our team drilled through the PFA for the first time to gain an understanding of firn structure constraining the PFA, to estimate the water volume within the PFA, and to measure PFA temperatures and densities. At our drill site in Southeast Greenland (~100 km Northwest of Kulusuk), water fills or partially fills the available firn pore space from depths of ~12 to 37 m. The temperature within the PFA depths is constant at 0.1 × 0.1° C while the 12 m of seasonally dry firn above the PFA has a temperature profile dominated by surface temperature forcing. Near the bottom of the PFA water completely fills available pore space as the firn is compressed to ice entrapping water filled bubbles, as opposed to air filled bubbles, which then start to refreeze. A PFA maximum density is reached as the water filling the pore space, increasing density, begins refreezing back into ice at a lower density. We define this depth as the pore water refreeze depth and use this depth as the bottom of the PFA to calculate volume. It is certain, however that a small amount of water does exist below this depth, which we do not account for. The density profile obtained from the ACT11B firn core, the closest seasonally dry firn core, is compared to both gravitational densities and high resolution densities derived from a neutron density probe at the PFA site. The

  14. Ultrasonic methods for measuring liquid viscosity and volume percent of solids

    Energy Technology Data Exchange (ETDEWEB)

    Sheen, S.H.; Chien, H.T.; Raptis, A.C.

    1997-02-01

    This report describes two ultrasonic techniques under development at Argonne National Laboratory (ANL) in support of the tank-waste transport effort undertaken by the U.S. Department of Energy in treating low-level nuclear waste. The techniques are intended to provide continuous on-line measurements of waste viscosity and volume percent of solids in a waste transport line. The ultrasonic technique being developed for waste-viscosity measurement is based on the patented ANL viscometer. Focus of the viscometer development in this project is on improving measurement accuracy, stability, and range, particularly in the low-viscosity range (<30 cP). A prototype instrument has been designed and tested in the laboratory. Better than 1% accuracy in liquid density measurement can be obtained by using either a polyetherimide or polystyrene wedge. To measure low viscosities, a thin-wedge design has been developed and shows good sensitivity down to 5 cP. The technique for measuring volume percent of solids is based on ultrasonic wave scattering and phase velocity variation. This report covers a survey of multiple scattering theories and other phenomenological approaches. A theoretical model leading to development of an ultrasonic instrument for measuring volume percent of solids is proposed, and preliminary measurement data are presented.

  15. Research Note Difference between low-volume and high-volume Andersen samplers in measuring atmospheric aerosols

    Institute of Scientific and Technical Information of China (English)

    Fengfu Fu; Nobuo Shinohaya; Mitsuo Ito; Xueqin Xu; Mincong Shen; Liangjun Xu

    2008-01-01

    The mass concentration and size distribution of aerosols in Tokaimura were investigated using a high-volume and a low-volume Andersen sampler. A difference was found using the two samplers: the concentration of total aerosols determined with the high-volume sampler is smaller than that of the low-volume sampler by 70-90% throughout the year. Compared to the high-volume sampler, low-volume sampler gave lower concentration for aerosols7μm, higher concentration for aerosols of 3.3-7.0μm and<1.1μm, though similar results for aerosols of 1.1-3.3μm. The low-volume sampler was found to have better separation efficiency and higher accuracy.

  16. The error analysis of Lobular and segmental division of right liver by volume measurement.

    Science.gov (United States)

    Zhang, Jianfei; Lin, Weigang; Chi, Yanyan; Zheng, Nan; Xu, Qiang; Zhang, Guowei; Yu, Shengbo; Li, Chan; Wang, Bin; Sui, Hongjin

    2017-07-01

    The aim of this study is to explore the inconsistencies between right liver volume as measured by imaging and the actual anatomical appearance of the right lobe. Five healthy donated livers were studied. The liver slices were obtained with hepatic segments multicolor-infused through the portal vein. In the slices, the lobes were divided by two methods: radiological landmarks and real anatomical boundaries. The areas of the right anterior lobe (RAL) and right posterior lobe (RPL) on each slice were measured using Photoshop CS5 and AutoCAD, and the volumes of the two lobes were calculated. There was no statistically significant difference between the volumes of the RAL or RPL as measured by the radiological landmarks (RL) and anatomical boundaries (AB) methods. However, the curves of the square error value of the RAL and RPL measured using CT showed that the three lowest points were at the cranial, intermediate, and caudal levels. The U- or V-shaped curves of the square error rate of the RAL and RPL revealed that the lowest value is at the intermediate level and the highest at the cranial and caudal levels. On CT images, less accurate landmarks were used to divide the RAL and RPL at the cranial and caudal layers. The measured volumes of hepatic segments VIII and VI would be less than their true values, and the measured volumes of hepatic segments VII and V would be greater than their true values, according to radiological landmarks. Clin. Anat. 30:585-590, 2017. © 2017 Wiley Periodicals, Inc. © 2017 Wiley Periodicals, Inc.

  17. Calculation of the Residual Blood Volume after Acute, Non-Ongoing Hemorrhage Using Serial Hematocrit Measurements and the Volume of Isotonic Fluid Infused: Theoretical Hypothesis Generating Study.

    Science.gov (United States)

    Oh, Won Sup; Chon, Sung-Bin

    2016-05-01

    Fluid resuscitation, hemostasis, and transfusion is essential in care of hemorrhagic shock. Although estimation of the residual blood volume is crucial, the standard measuring methods are impractical or unsafe. Vital signs, central venous or pulmonary artery pressures are inaccurate. We hypothesized that the residual blood volume for acute, non-ongoing hemorrhage was calculable using serial hematocrit measurements and the volume of isotonic solution infused. Blood volume is the sum of volumes of red blood cells and plasma. For acute, non-ongoing hemorrhage, red blood cell volume would not change. A certain portion of the isotonic fluid would increase plasma volume. Mathematically, we suggest that the residual blood volume after acute, non-ongoing hemorrhage might be calculated as 0·25N/[(Hct1/Hct2)-1], where Hct1 and Hct2 are the initial and subsequent hematocrits, respectively, and N is the volume of isotonic solution infused. In vivo validation and modification is needed before clinical application of this model.

  18. Technical Note: Stored grain volume measurement using a low density point cloud

    Science.gov (United States)

    The mass of stored grain is often determined from volume measurements by crop insurers, government auditors, and stored grain managers conducting inventories. Recent increases in bin size have accentuated the difficulty of accounting for irregularities and variations in surface conditions in calcula...

  19. Measurements of system sharpness for two digital breast tomosynthesis systems.

    Science.gov (United States)

    Marshall, N W; Bosmans, H

    2012-11-21

    The aim of this work was to propose system sharpness parameters for digital breast tomosynthesis (DBT) systems that include the influence of focus size and focus motion for use in quality assurance protocols. X-ray focus size was measured using a multiple pinhole test object, while detector presampling modulation transfer function (MTF) was measured from projection images of a 10 cm × 10 cm, 1 mm thick steel edge, for the Siemens Inspiration and Hologic Selenia Dimensions DBT systems. The height of the edge above the table was then varied from 1 to 78 mm. The MTF expected from theory for the projection images was calculated from the measured detector MTF, focus size MTF and focus motion MTF and was compared against measured curves. Two methods were used to measure the in-plane MTF in the DBT volume: a tungsten wire of diameter 25 µm and an Al edge 0.2 mm thick, both imaged with a 15 mm thick poly(methyl methacrylate) (PMMA) plate. The in-depth point spread function (PSF) was measured using an angled tungsten wire. The full 3D MTF was estimated with a 0.5 mm diameter aluminium bead held in a 45 mm thick PMMA phantom, with the bead 15 and 65 mm above the table. Inspiration DBT projection images are saved at native detector resolution (85 µm), while the Dimensions re-bins projections to 140 µm pixels (2 × 2 binning); both systems used 2 × 2 binning of projection data before reconstruction. The 50% point for the MTF (MTF(0.50)) measured in the DBT projection images for the tube-travel direction fell as a function of height above the table from 3.60 to 0.90 mm(-1) for the Inspiration system and from 2.50 to 1.20 mm(-1) for the Dimensions unit. The maximum deviation of measured MTF(0.50) from the calculated value was 13%. MTF(0.50) measured in-plane (tube-travel direction) fell as a function of height above the table from 1.66 to 0.97 mm(-1) for the Inspiration system and from 2.21 to 1.31 mm(-1) for the Dimensions system. The full-width half-maximum for the in

  20. Is the difference in the volume of the pharyngeal space, as measured by acoustic pharyngometry, before and after tonsillectomy proportional to the volume of the excised tonsils?

    Directory of Open Access Journals (Sweden)

    Renata C. Di Francesco

    Full Text Available OBJECTIVE: Adenotonsillectomy is recognized as an effective therapy for snoring and sleep disorders in children. It is important to understand whether adenotonsillectomy significantly increases the volume of the pharyngeal space. The goal of this study was to evaluate the change in oropharyngeal volume after adenotonsillectomy and the correlation of this change with the objective volume of the tonsils and body mass index. METHODS: We included 27 subjects (14 males with snoring caused by tonsil and adenoid hypertrophy. The mean age of the subjects was 7.92 (±2.52 years. Children with craniofacial malformations or neuromuscular diseases or syndromes were excluded. The parents/caregivers answered an adapted questionnaire regarding sleep-disordered breathing. All patients were subjected to weight and height measurements and body mass index was calculated. The subjects underwent pharyngometry before and after adenotonsillectomy and the volume of both excised tonsils together was measured in cm3 in the operating room. RESULTS: Pharyngometric analysis showed that the mean pharyngeal volume was 28.63 (±5.57 cm3 before surgery and 31.23 (±6.76 cm3 after surgery; the volume of the oropharynx was significantly increased post-surgery (p=0.015, Wilcoxon test. No correlation was found between the objective tonsil volume and the post-surgical volume increase (p=0.6885. There was a fair correlation between the oropharyngeal volume and body mass index (p=0.0224. CONCLUSION: Adenotonsillectomy increases the volume of the pharyngeal space, but this increase does not correlate with the objective tonsil size. Furthermore, greater BMI was associated with a smaller increase in the pharyngeal volume. Oropharyngeal structures and craniofacial morphology may also play a role in the increase in oropharyngeal volume.

  1. Development of ultrasonic velocity profile method for flow rate measurements of power plant (effect of measurement volume on turbulent flow measurement)

    Energy Technology Data Exchange (ETDEWEB)

    Hiroshige, Kikura; Gentaro, Yamanaka; Tsuyoshi, Taishi; Masanori, Aritomi [Tokyo Institute of Technology, Tokyo (Japan); Yasushi, Takeda [Paul Scherrer Inst. (PSI), Villigen (Switzerland); Michitsugu, Mori [Tokyo Electric Power Co., Inc. (Japan)

    2001-07-01

    Ultrasonic Velocity Profile method has many advantages for flow rate measurement of power plant over the conventional flow measurement methods, such as measurement of the instantaneous velocity profile along the measuring line and its applicability to opaque liquids. Furthermore, the method has an advantage of being non-intrusive. Hence, it is applicable to various flow conditions, although it requires a relatively large measurement volume. In this paper, the effects of the measurement volume on the mean velocity profile for flow rate measurements of power plant and the Reynolds stress measurement have been investigated for fully developed turbulent pipe flows in a vertical pipe. The results are then compared with data obtained by Direct Numerical Simulation (DNS). (authors)

  2. Directional spectral emissivity measurement system

    Science.gov (United States)

    Halyo, Nesim (Inventor); Pandey, Dhirendra K. (Inventor)

    1992-01-01

    Apparatus and process for determining the emissivity of a test specimen including an integrated sphere having two concentric walls with a coolant circulating therebetween, and disposed within a chamber which may be under ambient, vacuum or inert gas conditions. A reference sample is disposed within the sphere with a monochromatic light source in optical alignment therewith. A pyrometer is in optical alignment with the test sample for obtaining continuous test sample temperature measurements during a test. An arcuate slit port is provided through the spaced concentric walls of the integrating sphere with a movable monochromatic light source extending through and movable along the arcuate slit port. A detector system extends through the integrating sphere for continuously detecting an integrated signal indicative of all radiation within its field of view, as a function of the emissivity of the test specimen at various temperatures and various angle position of the monochromatic light source. A furnace for heating the test sample to approximately 3000 K. and control mechanism for transferring the heated sample from the furnace to the test sample port in the integrating sphere is also contained within the chamber.

  3. Indicators System for Poverty Measurement

    Directory of Open Access Journals (Sweden)

    Constantin Mitrut

    2006-10-01

    Full Text Available Poverty represents a life aspect which is focusing the attention of both the macroeconomic analysis and the international comparisons. In order to measure the level being recorded by this phenomenon, there is a system of indicators which are used in order to underline, in a correlated manner, a number of aspects which are characterizing, quality and quantity wise, the evolution of the poverty in a specific country or, to a larger extent, through comparative surveys, at international level. Despite the fact that they are not the only instrument being used within the process of comparison of the stages of social and economic development at the international level, however the poverty indicators are providing a clear significance to the worked out surveys. In fact, the very purpose of the economic activity consists of increasing welfare and, as much as possible, at least reducing, if not eradicating, the poverty. The present work is broadly presenting the methodology as well as, both theoretical and practical, the way of computing the poverty, making a synthesis of the specific used indicators.

  4. Validation of Respiratory Inductance Plethysmography for Measuring Tidal Volume in Swine

    OpenAIRE

    2015-01-01

    Measuring tidal volume (VT) in nonintubated swine or swine with leaking breathing circuits is challenging. The aim of this study was to validate respiratory inductance plethysmography (RIP) for measuring VT in swine that are comparable in size to adult humans. To determine calibration curves, VT and RIP readings were obtained from anesthetized swine (n = 8; weight, 46–50 kg) during positive-pressure (mechanical) ventilation and spontaneous breathing. For positive-pressure ventilation, 6 pigs ...

  5. Sonographic Parameters for Prediction of Miscarriage: Role of 3-Dimensional Volume Measurement.

    Science.gov (United States)

    Wie, Jeong Ha; Choe, Suyearn; Kim, Sa Jin; Shin, Jong Chul; Kwon, Ji Young; Park, In Yang

    2015-10-01

    To evaluate the value of volume measurement using 3-dimensional sonography for prediction of miscarriage. We prospectively enrolled 188 singleton pregnant women at 5 to 9 weeks' gestation. The 3-dimensional sonographic gestational sac volume and yolk sac volume were measured together with the fetal heart rate, gestational sac diameter, and yolk sac diameter. For each sonographic parameter, nomograms were created; z scores were calculated for each measurement, and the values were compared between miscarriage and ongoing pregnancy groups. Sonographic parameters for prediction of miscarriage were evaluated by multivariate analysis, and the screening performance was assessed by a receiver operating characteristic curve. Among the 188 pregnancies, 30 (16.0%) had miscarriage. Multivariate analysis showed that fetal heart rate below the 5th percentile (odds ratio, 6.43), gestational sac diameter below the 5th percentile (odds ratio, 4.87), gestational sac volume below the 5th percentile (odds ratio, 5.25), and yolk sac diameter below the 2.5th or above the 97.5th percentile (odds ratio, 15.86) were significant predictors of miscarriage (P = .018; P = .018; P = .033; and P < .001, respectively). At a false-positive rate of 30%, the detection rate for miscarriage in screening by a combination of fetal heart rate, gestational sac diameter, gestational sac volume, and yolk sac diameter was 77.8%. A small-for-gestational-age gestational sac volume is a significant sonographic predictor of miscarriage, as are fetal bradycardia, a small gestational sac diameter, and a small or large yolk sac diameter. © 2015 by the American Institute of Ultrasound in Medicine.

  6. NASA System Safety Handbook. Volume 2: System Safety Concepts, Guidelines, and Implementation Examples

    Science.gov (United States)

    Dezfuli, Homayoon; Benjamin, Allan; Everett, Christopher; Feather, Martin; Rutledge, Peter; Sen, Dev; Youngblood, Robert

    2015-01-01

    This is the second of two volumes that collectively comprise the NASA System Safety Handbook. Volume 1 (NASASP-210-580) was prepared for the purpose of presenting the overall framework for System Safety and for providing the general concepts needed to implement the framework. Volume 2 provides guidance for implementing these concepts as an integral part of systems engineering and risk management. This guidance addresses the following functional areas: 1.The development of objectives that collectively define adequate safety for a system, and the safety requirements derived from these objectives that are levied on the system. 2.The conduct of system safety activities, performed to meet the safety requirements, with specific emphasis on the conduct of integrated safety analysis (ISA) as a fundamental means by which systems engineering and risk management decisions are risk-informed. 3.The development of a risk-informed safety case (RISC) at major milestone reviews to argue that the systems safety objectives are satisfied (and therefore that the system is adequately safe). 4.The evaluation of the RISC (including supporting evidence) using a defined set of evaluation criteria, to assess the veracity of the claims made therein in order to support risk acceptance decisions.

  7. Scanning laser optical computed tomography system for large volume 3D dosimetry

    Science.gov (United States)

    Dekker, Kurtis H.; Battista, Jerry J.; Jordan, Kevin J.

    2017-04-01

    Stray light causes artifacts in optical computed tomography (CT) that negatively affect the accuracy of radiation dosimetry in gels or solids. Scatter effects are exacerbated by a large dosimeter volume, which is desirable for direct verification of modern radiotherapy treatment plans such as multiple-isocenter radiosurgery. The goal in this study was to design and characterize an optical CT system that achieves high accuracy primary transmission measurements through effective stray light rejection, while maintaining sufficient scan speed for practical application. We present an optical imaging platform that uses a galvanometer mirror for horizontal scanning, and a translation stage for vertical movement of a laser beam and small area detector for minimal stray light production and acceptance. This is coupled with a custom lens-shaped optical CT aquarium for parallel ray sampling of projections. The scanner images 15 cm diameter, 12 cm height cylindrical volumes at 0.33 mm resolution in approximately 30 min. Attenuation coefficients reconstructed from CT scans agreed with independent cuvette measurements within 2% for both absorbing and scattering solutions as well as small 1.25 cm diameter absorbing phantoms placed within a large, scattering medium that mimics gel. Excellent linearity between the optical CT scanner and the independent measurement was observed for solutions with between 90% and 2% transmission. These results indicate that the scanner should achieve highly accurate dosimetry of large volume dosimeters in a reasonable timeframe for clinical application to radiotherapy dose verification procedures.

  8. Scanning laser optical computed tomography system for large volume 3D dosimetry.

    Science.gov (United States)

    Dekker, Kurtis H; Battista, Jerry J; Jordan, Kevin J

    2017-04-07

    Stray light causes artifacts in optical computed tomography (CT) that negatively affect the accuracy of radiation dosimetry in gels or solids. Scatter effects are exacerbated by a large dosimeter volume, which is desirable for direct verification of modern radiotherapy treatment plans such as multiple-isocenter radiosurgery. The goal in this study was to design and characterize an optical CT system that achieves high accuracy primary transmission measurements through effective stray light rejection, while maintaining sufficient scan speed for practical application. We present an optical imaging platform that uses a galvanometer mirror for horizontal scanning, and a translation stage for vertical movement of a laser beam and small area detector for minimal stray light production and acceptance. This is coupled with a custom lens-shaped optical CT aquarium for parallel ray sampling of projections. The scanner images 15 cm diameter, 12 cm height cylindrical volumes at 0.33 mm resolution in approximately 30 min. Attenuation coefficients reconstructed from CT scans agreed with independent cuvette measurements within 2% for both absorbing and scattering solutions as well as small 1.25 cm diameter absorbing phantoms placed within a large, scattering medium that mimics gel. Excellent linearity between the optical CT scanner and the independent measurement was observed for solutions with between 90% and 2% transmission. These results indicate that the scanner should achieve highly accurate dosimetry of large volume dosimeters in a reasonable timeframe for clinical application to radiotherapy dose verification procedures.

  9. Bymixer provides on-line calibration of measurement of CO2 volume exhaled per breath.

    Science.gov (United States)

    Breen, P H; Serina, E R

    1997-01-01

    The measurement of CO2 volume exhaled per breath (VCO2.br) can be determined during anesthesia by the multiplication and integration of tidal flow (V) and PCO2. During side-stream capnometry, PCO2 must be advanced in time by transport delay (TD), the time to suction gas through the sampling tube. During ventilation, TD can vary due to sample line connection internal volume or flow rate changes. To determine correct TD and measure accurate VCO2.br during actual ventilation. TD can be iteratively adjusted (TDADJ) until VCO2-br/tidal volume equals PCO2 measured in a mixed expired gas collection (PECO2) (J Appl. Physiol. 72:2029-2035, 1992). However. PECO2 is difficult to measure during anesthesia because CO2 is absorbed in the circle circuit. Accordingly, we implemented a bypass flow-mixing chamber device (bymixer) that was interposed in the expiration limb of the circle circuit and accurately measured PECO2 over a wide range of conditions of ventilation of a test lung-metabolic chamber (regression slope = 1.01: R2 = 0.99). The bymixer response (time constant) varied from 18.1 +/- 0.03 sec (12.5 l/min ventilation) to 66.7 +/- 0.9 sec (2.5 l/min). Bymixer PECO2 was used to correctly determine TDADJ (without interrupting respiration) to enable accurate measurement of VCO2.br over widely changing expiratory flow patterns.

  10. Mexico City air quality research initiative. Volume IV. Characterization and measurement

    Energy Technology Data Exchange (ETDEWEB)

    Mauzy, A. [ed.

    1994-04-01

    This volume describes the methods and the data gathered in an attempt to measure and characterize the meteorological factors and the concentration of different pollutants in the Mexico City Metropolitan Area. The main objective of this document was to provide input for the simulation models and to obtain information that could be used to test and improve the models` performance. Four field campaigns were conducted, as well as routine monitoring, in order to obtain a database of atmospheric dynamics and air pollution characteristics. Sections include Airborne measurements, Remote sensing measurements, and Traditional (in situ) measurements.

  11. Spatial Visualization Tasks To Support Students’ Spatial Structuring In Learning Volume Measurement

    Directory of Open Access Journals (Sweden)

    Shintia Revina

    2011-07-01

    Full Text Available Many prior researches found that most of students in grade five tendedto have difficulty in fully grasping the concept of volume measurementbecause they have to build their competence in spatial structuring. The unit of volume “packing” measurement must be integrated andcoordinated in three-dimension. On the other hand, it is revealed theerrors that students made on the volume measurement tasks with threedimensional cube arrays are related to some aspects of spatialvisualization, such as the skill to "read off" two-dimensionalrepresentation of solid objects. For those reasons, this research is aimed to develop classroom activities with the use of spatial visualization tasks to support students’ spatial structuring in learning volume measurement. Consequently, design research was chosen as an appropriate means to achieve this research goal. In this research, a sequence of instructional activities is designed and developed based on the hypothesis of students’ learning processes. This research was conducted in grade 5 of SD Pupuk Sriwijaya Palembang, Indonesia

  12. Visceral adipose tissue area measurement at a single level: can it represent visceral adipose tissue volume?

    Science.gov (United States)

    Noumura, Yusuke; Kamishima, Tamotsu; Sutherland, Kenneth; Nishimura, Hideho

    2017-08-01

    Measurement of visceral adipose tissue (VAT) needs to be accurate and sensitive to change for risk monitoring. The purpose of this study is to determine the CT slice location where VAT area can best reflect changes in VAT volume and body weight. 60 plain abdominal CT images from 30 males [mean age (range) 51 (41-68) years, mean body weight (range) 71.1 (101.9-50.9) kg] who underwent workplace screenings twice within a 1-year interval were evaluated. Automatically calculated and manually corrected areas of the VAT of various scan levels using "freeform curve" region of interest on CT were recorded and compared with body weight changes. The strongest correlations of VAT area with VAT volume and body weight changes were shown in a slice 3 cm above the lower margin of L3 with r values of 0.853 and 0.902, respectively. VAT area measurement at a single level 3 cm above the lower margin of the L3 vertebra is feasible and can reflect changes in VAT volume and body weight. Advances in knowledge: As VAT area at a CT slice 3cm above the lower margin of L3 can best reflect interval changes in VAT volume and body weight, VAT area measurement should be selected at this location.

  13. Measurement System and Calibration report

    DEFF Research Database (Denmark)

    Vesth, Allan; Kock, Carsten Weber

    The report describes power curve measurements carried out on a given wind turbine. The measurements are carried out in accordance to Ref. [1]. A site calibration has been carried out; see Ref. [2], and the measured flow correction factors for different wind directions are used in the present...

  14. Validity and intra- and interobserver reliability of an indirect volume measurements in patients with upper extremity lymphedema

    NARCIS (Netherlands)

    Meijer, R.S.; Rietman, J.S.; Geertzen, J.H.B.; Bosmans, J.C.; Dijkstra, P.U.

    2004-01-01

    We investigated a method of indirect volume measurement that utilized surface measurements and a simplified formula derived from the formula for a frustum (Sitzia's method) to determine limb volumes in patients with breast cancer-related lymphedema of the upper extremity. Repeated measurements of up

  15. Validity and intra- and interobserver reliability of an indirect volume measurements in patients with upper extremity lymphedema

    NARCIS (Netherlands)

    Meijer, R.S.; Rietman, J.S.; Geertzen, J.H.B.; Bosmans, J.C.; Dijkstra, P.U.

    We investigated a method of indirect volume measurement that utilized surface measurements and a simplified formula derived from the formula for a frustum (Sitzia's method) to determine limb volumes in patients with breast cancer-related lymphedema of the upper extremity. Repeated measurements of

  16. Repeatability of Volume and Regional Body Composition Measurements of the Lower Limb Using Dual-energy X-ray Absorptiometry

    DEFF Research Database (Denmark)

    Gjorup, Caroline A; Zerahn, Bo; Juul, Sarah

    2016-01-01

    Lower limb lymphedema is a dynamic condition in which tissue composition and volume measurements are affected. Various definitions of lower limb lymphedema exist but volume differences between the limbs are widely used. It is therefore necessary to have a readily available noninvasive measurement...... of agreement on the Bland-Altman plots. These results confirm DXA to be a highly repeatable method for volume and tissue composition measurements of the lower limb. In a population at risk of lymphedema, DXA offers a clinically readily available noninvasive method allowing multiple measurements of volume...... and tissue composition on a routine basis, important for diagnosing, monitoring, managing, and researching lymphedema....

  17. Mobile measurement system for wind turbines

    Energy Technology Data Exchange (ETDEWEB)

    Kildemoes Moeller, T.

    1997-06-01

    The aim of this project `Udviklingsafproevning af smaa moellevinger` has been to develop a mobile measurement system for wind turbines. The following report describes the measurement system. The project has been financed by the Danish Ministry of Energy. (au)

  18. Study of the $\\bar K N$ system and coupled channels in a finite volume

    CERN Document Server

    Torres, A Martínez; Jido, D; Oset, E

    2013-01-01

    We investigate the $\\bar KN$ and coupled channels system in a finite volume and study the properties of the $\\Lambda(1405)$ resonance. We calculate the energy levels in a finite volume and solve the inverse problem of determining the resonance position in the infinite volume. We devise the best strategy of analysis to obtain the two poles of the $\\Lambda(1405)$ in the infinite volume case, with sufficient precision to distinguish them.

  19. Ionization-cluster distributions of alpha-particles in nanometric volumes of propane: measurement and calculation.

    Science.gov (United States)

    De Nardo, L; Colautti, P; Conte, V; Baek, W Y; Grosswendt, B; Tornielli, G

    2002-12-01

    The probability of the formation of ionization clusters by primary alpha-particles at 5.4 MeV in nanometric volumes of propane was studied experimentally and by Monte Carlo simulation, as a function of the distance between the center line of the particle beam and the center of the target volume. The volumes were of cylindrical shape, 3.7 mm in diameter and height. As the investigations were performed at gas pressures of 300 Pa and 350 Pa, the dimensions of the target volume were equivalent to 20.6 nm or 24.0 nm in a material of density 1.0 g/cm(3). The dependence of ionization-cluster formation on distance was studied up to values equivalent to about 70 nm. To validate the measurements, a Monte Carlo model was developed which allows the experimental arrangement and the interactions of alpha-particles and secondary electrons in the counter gas to be properly simulated. This model is supplemented by a mathematical formulation of cluster size formation in nanometric targets. The main results of our study are (i) that the mean ionization-cluster size in the delta-electron cloud of an alpha-particle track segment, decreases as a function of the distance between the center line of the alpha-particle beam and the center of the sensitive target volume to the power of 2.6, and (ii) that the mean cluster size in critical volumes and the relative variance of mean cluster size due to delta-electrons are invariant at distances greater than about 20 nm. We could imagine that the ionization-cluster formation in nanometric volumes might in future provide the physical basis for a redefinition of radiation quality.

  20. Systems Book for a Student Information System. End of Project Report, 1968-1971, Volume II.

    Science.gov (United States)

    Western Nevada Regional Education Center, Lovelock.

    The necessary handbooks for use of the Student Information System (SIS), developed and tested by the Western Nevada Regional Education Center under a 1968-71 Title III (Elementary and Secondary Education Act) grant, are presented in this volume. As noted, the purpose of the SIS is to supply data and information to persons or organizations who make…

  1. Static contact angle measurement at different volumes of a drop sitting on non-ferrous metals

    Directory of Open Access Journals (Sweden)

    Feoktistov Dmitriy

    2016-01-01

    Full Text Available The paper presents the experimental study of the effect of the liquid volume on the static contact angle under the condition of the stationary contact line on the rough and polished surfaces of non-ferrous metals. The experiments were carried out using the shadow optical system. Comparison between two methods of drop profile processing was conducted. It was found that in addition to the friction and gravity forces, the structure of the non-ferrous metals significantly influence on the static contact angle during changing the drop volume.

  2. Cumulative Ocean Volume Estimates of the Solar System

    Science.gov (United States)

    Frank, E. A.; Mojzsis, S. J.

    2010-12-01

    Although there has been much consideration for habitability in silicate planets and icy bodies, this information has never been quantitatively gathered into a single approximation encompassing our solar system from star to cometary halo. Here we present an estimate for the total habitable volume of the solar system by constraining our definition of habitable environments to those to which terrestrial microbial extremophiles could theoretically be transplanted and yet survive. The documented terrestrial extremophile inventory stretches environmental constraints for habitable temperature and pH space of T ~ -15oC to 121oC and pH ~ 0 to 13.5, salinities >35% NaCl, and gamma radiation doses of 10,000 to 11,000 grays [1]. Pressure is likely not a limiting factor to life [2]. We applied these criteria in our analysis of the geophysical habitable potential of the icy satellites and small icy bodies. Given the broad spectrum of environmental tolerance, we are optimistic that our pessimistic estimates are conservative. Beyond the reaches of our inner solar system's conventional habitable zone (Earth, Mars and perhaps Venus) is Ceres, a dwarf planet in the habitable zone that could possess a significant liquid water ocean if that water contains anti-freezing species [3]. Yet further out, Europa is a small icy satellite that has generated much excitement for astrobiological potential due to its putative subsurface liquid water ocean. It is widely promulgated that the icy moons Enceladus, Triton, Callisto, Ganymede, and Titan likewise have also sustained liquid water oceans. If oceans in Europa, Enceladus, and Triton have direct contact with a rocky mantle hot enough to melt, hydrothermal vents could provide an energy source for chemotrophic organisms. Although oceans in the remaining icy satellites may be wedged between two layers of ice, their potential for life cannot be precluded. Relative to the Jovian style of icy satellites, trans-neptunian objects (TNOs) - icy bodies

  3. Forearm skin tissue dielectric constant measured at 300 MHz: effect of changes in skin vascular volume and blood flow.

    Science.gov (United States)

    Mayrovitz, Harvey N; Guo, Xiaoran; Salmon, Mark; Uhde, Matt

    2013-01-01

    Skin tissue dielectric constant (TDC) values measured via the open-ended coaxial probe method are useful non-invasive indices of local skin tissue water. However, the effect of skin blood flow (SBF) or skin blood volume (SBV) on TDC values is unknown. To determine the magnitude of such effects, we decreased forearm SBV via vertical arm raising for 5 min (test 1) and increased SBV by bicep cuff compression to 50 mmHg for 5 min (test 2) in 20 healthy supine subjects (10 men). TDC values were measured to a depth of 1·5 mm on anterior forearm, and SBF was measured with laser-Doppler system simultaneously on forearm and finger. Results indicate that decreasing vascular volume (test 1) was associated with a small but statistically significant reduction in TDC (3·0 ± 4·3%, P = 0·003) and increasing vascular volume (test 2) was associated with a slight but statistically significant increase in TDC (3·5 ± 3·0%, PTDC values (3·0-3·5%) over the wide range of induced SBV and SBF changes suggest a minor effect on clinically determined TDC values because of SBV or SBF changes or differences when comparing TDC longitudinally over time or among individuals of different groups in a research setting.

  4. The Applications of Measurement System for Crankshaft

    Institute of Scientific and Technical Information of China (English)

    DAI Shangping; GAO Li; GAO Kai

    2006-01-01

    This paper will introduce two types of multi-parameter co-measuring system and their application in the production. The first is crankshaft bent deformation measuring machine system. The second is the crankshaft pneumatic-electric measuring system. They have been used in final inspection procedure of automation line for crankshaft of automobie engine with good results, the structure principle and soft clash technological process of the measurement system are presented.

  5. Influence of the turbinate volumes as measured by magnetic resonance imaging on nasal air conditioning.

    Science.gov (United States)

    Lindemann, Joerg; Tsakiropoulou, Evangelia; Vital, Victor; Keck, Tilman; Leiacker, Richard; Pauls, Sandra; Wacke, Florian; Wiesmiller, Kerstin M

    2009-01-01

    Changes in nasal airflow caused by varying intranasal volumes and cross-sectional areas affect the contact between air and surrounding mucosa entailing alterations in nasal air conditioning. This study evaluates the correlation between nasal air conditioning and the volumes of the inferior and middle turbinates as measured by magnetic resonance imaging (MRI). Fourteen healthy volunteers were enrolled. Each volunteer had been examined by rhinomanometry, acoustic rhinometry, intranasal air temperature, and humidity measurements at defined intranasal sites as well as MRI of the nasal cavity and the paranasal sinuses. The volumetric data of the turbinates was based on the volumetric software Amira. Comparable results were obtained regarding absolute humidity values and temperature values within the nasal valve area and middle turbinate area for both the right and the left side of the nasal cavity. No statistically significant differences were found in the rhinomanometric values and the acoustic rhinometry results of both sides (p > 0.05). No statistical correlations were found between the volumes of the inferior (mean, 6.1 cm3) and middle turbinate (mean, 1.8 cm3) and the corresponding humidity and temperature values. Additionally, the air temperature and humidity values did not correlate with the rhinometrical endonasal volumes (0-20 mm and 20-50 mm from the nasal entrance). The normal range of volumes of the inferior and middle turbinate does not seem to have a significant impact on intranasal air conditioning in healthy subjects. The exact limits where alterations of the turbinate volume negatively affect nasal air conditioning are still unknown.

  6. Three-dimensional direct measurement of cardiomyocyte volume, nuclearity, and ploidy in thick histological sections.

    Science.gov (United States)

    Bensley, Jonathan Guy; De Matteo, Robert; Harding, Richard; Black, Mary Jane

    2016-01-01

    Quantitative assessment of myocardial development and disease requires accurate measurement of cardiomyocyte volume, nuclearity (nuclei per cell), and ploidy (genome copies per cell). Current methods require enzymatically isolating cells, which excludes the use of archived tissue, or serial sectioning. We describe a method of analysis that permits the direct simultaneous measurement of cardiomyocyte volume, nuclearity, and ploidy in thick histological sections. To demonstrate the utility of our technique, heart tissue was obtained from four species (rat, mouse, rabbit, sheep) at up to three life stages: prenatal, weaning and adulthood. Thick (40 μm) paraffin sections were stained with Wheat Germ Agglutinin-Alexa Fluor 488 to visualise cell membranes, and DAPI (4',6-diamidino-2-phenylindole) to visualise nuclei and measure ploidy. Previous methods have been restricted to thin sections (2-10 μm) and offer an incomplete picture of cardiomyocytes. Using confocal microscopy and three-dimensional image analysis software (Imaris Version 8.2, Bitplane AG, Switzerland), cardiomyocyte volume, nuclearity, and ploidy were measured. This method of staining and analysis of cardiomyocytes enables accurate morphometric measurements in thick histological sections, thus unlocking the potential of archived tissue. Our novel time-efficient method permits the entire cardiomyocyte to be visualised directly in 3D, eliminating the need for precise alignment of serial sections.

  7. Three-dimensional direct measurement of cardiomyocyte volume, nuclearity, and ploidy in thick histological sections

    Science.gov (United States)

    Bensley, Jonathan Guy; de Matteo, Robert; Harding, Richard; Black, Mary Jane

    2016-04-01

    Quantitative assessment of myocardial development and disease requires accurate measurement of cardiomyocyte volume, nuclearity (nuclei per cell), and ploidy (genome copies per cell). Current methods require enzymatically isolating cells, which excludes the use of archived tissue, or serial sectioning. We describe a method of analysis that permits the direct simultaneous measurement of cardiomyocyte volume, nuclearity, and ploidy in thick histological sections. To demonstrate the utility of our technique, heart tissue was obtained from four species (rat, mouse, rabbit, sheep) at up to three life stages: prenatal, weaning and adulthood. Thick (40 μm) paraffin sections were stained with Wheat Germ Agglutinin-Alexa Fluor 488 to visualise cell membranes, and DAPI (4‧,6-diamidino-2-phenylindole) to visualise nuclei and measure ploidy. Previous methods have been restricted to thin sections (2–10 μm) and offer an incomplete picture of cardiomyocytes. Using confocal microscopy and three-dimensional image analysis software (Imaris Version 8.2, Bitplane AG, Switzerland), cardiomyocyte volume, nuclearity, and ploidy were measured. This method of staining and analysis of cardiomyocytes enables accurate morphometric measurements in thick histological sections, thus unlocking the potential of archived tissue. Our novel time-efficient method permits the entire cardiomyocyte to be visualised directly in 3D, eliminating the need for precise alignment of serial sections.

  8. Quantitative measurement of regional lung gas volume by synchrotron radiation computed tomography

    Energy Technology Data Exchange (ETDEWEB)

    Monfraix, Sylvie [European Synchrotron Radiation Facility, BP 220, F-38043 Grenoble (France); Bayat, Sam [European Synchrotron Radiation Facility, BP 220, F-38043 Grenoble (France); Porra, Liisa [Department of Physical Sciences, University of Helsinki, POB 64, FIN-00014 Helsinki (Finland); Berruyer, Gilles [European Synchrotron Radiation Facility, BP 220, F-38043 Grenoble (France); Nemoz, Christian [European Synchrotron Radiation Facility, BP 220, F-38043 Grenoble (France); Thomlinson, William [Canadian Light Source, 101 Perimeter Road, Saskatoon, SK S7N 0X4 (Canada); Suortti, Pekka [Department of Physical Sciences, University of Helsinki, POB 64, FIN-00014 Helsinki (Finland); Sovijaervi, Anssi R A [Department of Clinical Physiology and Nuclear Medicine, Helsinki University Central Hospital, POB 340, FIN-00029 HUS, Helsinki (Finland)

    2005-01-07

    The aim of this study was to assess the feasibility of a novel respiration-gated spiral synchrotron radiation computed tomography (SRCT) technique for direct quantification of absolute regional lung volumes, using stable xenon (Xe) gas as an inhaled indicator. Spiral SRCT with K-edge subtraction using two monochromatic x-ray beams was used to visualize and directly quantify inhaled Xe concentrations and airspace volumes in three-dimensional (3D) reconstructed lung images. Volume measurements were validated using a hollow Xe-filled phantom. Spiral images spanning 49 mm in lung height were acquired following 60 breaths of an 80% Xe-20% O{sub 2} gas mixture, in two anaesthetized and mechanically ventilated rabbits at baseline and after histamine aerosol inhalation. Volumetric images of 20 mm lung sections were obtained at functional residual capacity (FRC) and at end-inspiration. 3D images showed large patchy filling defects in peripheral airways and alveoli following histamine provocation. Local specific lung compliance was calculated based on FRC/end-inspiration images in normal lung. This study demonstrates spiral SRCT as a new technique for direct determination of regional lung volume, offering possibilities for non-invasive investigation of regional lung function and mechanics, with a uniquely high spatial resolution. An example of non-uniform volume distribution in rabbit lung following histamine inhalation is presented.

  9. Decreased left temporal lobe volume of panic patients measured by magnetic resonance imaging

    Energy Technology Data Exchange (ETDEWEB)

    Uchida, R.R.; Del-Ben, C.M.; Araujo, D.; Crippa, J.A.; Graeff, F.G. [Sao Paulo Univ., Ribeirao Preto, SP (Brazil). Dept. de Neurologia e Psicologia Medica]. E-mail: fgraeff@keynet.com.br; Santos, A.C. [Sao Paulo Univ., Ribeirao Preto, SP (Brazil). Dept. de Clinica Medica; Guimaraes, F.S. [Sao Paulo Univ., Ribeirao Preto, SP (Brazil). Dept. de Farmacologia

    2003-07-01

    Reported neuroimaging studies have shown functional and morphological changes of temporal lobe structures in panic patients, but only one used a volumetric method. The aim of the present study was to determine the volume of temporal lobe structures in patients with panic disorder, measured by magnetic resonance imaging. Eleven panic patients and eleven controls matched for age, sex, handedness, socioeconomic status and years of education participated in the study. The mean volume of the left temporal lobe of panic patients was 9% smaller than that of controls (t{sub 21} = 2.37, P = 0.028). In addition, there was a trend (P values between 0.05 and 0.10) to smaller volumes of the right temporal lobe (7%, t{sub 21} = 1.99, P = 0.06), right amygdala (8%, t{sub 21} = 1.83, P = 0.08), left amygdala (5%, t{sub 21} = 1.78, P 0.09) and left hippocampus (9%, t{sub 21} = 1.93, P = 0.07) in panic patients compared to controls. There was a positive correlation between left hippocampal volume and duration of panic disorder (r = 0.67, P = 0.025), with recent cases showing more reduction than older cases. The present results show that panic patients have a decreased volume of the left temporal lobe and indicate the presence of volumetric abnormalities of temporal lobe structures. (author)

  10. State energy price system. Volume I: overview and technical documentation

    Energy Technology Data Exchange (ETDEWEB)

    Fang, J.M.; Nieves, L.A.; Sherman, K.L.; Hood, L.J.

    1982-06-01

    This study utilizes existing data sources and previous analyses of state-level energy prices to develop consistent state-level energy prices series by fuel type and by end-use sector. The fuels are electricity, natural gas, coal, distillate fuel oil, motor gasoline, diesel, kerosene, jet fuel, residual fuel, and liquefied petroleum gas. The end-use sectors are residential, commercial, industrial, transportation, and electric utility. Based upon an evaluation of existing data sources, recommendations were formulated on the feasible approaches for developing a consistent state energy price series. The data series were compiled based upon the approaches approved after a formal EIA review. Detailed documentation was provided, including annual updating procedures. Recommendations were formulated for future improvements in the collection of data or in data processing. Generally, the geographical coverage includes the 50 states and the District of Columbia. Information on state-level energy use was generally taken from the State Energy Data System (SEDS). Corresponding average US prices are also developed using volumes reported in SEDS. To the extent possible, the prices developed are quantity weighted average retail prices. Both a Btu price series and a physical unit price series are developed for each fuel. The period covered by the data series is 1970 through 1980 for most fuels, though prices for electricity and natural gas extend back to 1960. (PSB)

  11. Comparison of annular diffusion denuder and high volume air samplers for measuring per- and polyfluoroalkyl substances in the atmosphere.

    Science.gov (United States)

    Ahrens, Lutz; Shoeib, Mahiba; Harner, Tom; Lane, Douglas A; Guo, Rui; Reiner, Eric J

    2011-12-15

    Overestimation of the particle phase concentration collected on glass-fiber filters (GFFs) has been reported for perfluoroalkyl carboxylic acids (PFCAs) using conventional high volume air samplers. In this study, per- and polyfluoroalkyl substances (PFASs) were determined in the gas and particulate phases using colocated annular diffusion denuder and high volume air samplers at a semiurban site in Toronto, Canada, in winter 2010. Samples were analyzed for 7 PFAS classes (i.e., PFCAs, perfluoro-alkane sulfonic acids (PFSAs), fluorotelomer alcohols (FTOHs), fluorotelomer methacrylates (FTMACs), fluorotelomer acrylates (FTACs), perfluorooctane sulfonamides (FOSAs), and perfluorooctane sulfonamidoethanols (FOSEs)). The gas diffusion coefficients for individual PFASs were calculated and the denuder performance was evaluated. Modeled subcooled liquid vapor pressures (p(L)) correlated well with the vapor phase breakthrough for the denuder and high volume air systems. Total air concentrations for PFASs measured using annular diffusion denuders and high volume samplers were in agreement within a factor of 4; however, much greater differences were observed for measurements of gas-particle partitioning. Vapor phase PFSAs and PFCAs can adsorb to the GFF using high volume air samplers, resulting in much higher particle-associated fractions for these chemicals compared to the annular diffusion denuder sampler. This effect was not observed for the FTOHs, FTMACs, FTACs, FOSAs, and FOSEs. Thus, for investigations of gas-particle partitioning of PFSAs and PFCAs, the diffusion denuder sampler is the preferred method. The results of this study improve our understanding of the gas-particle partitioning of PFASs, which is important for modeling their long-range transport in air.

  12. Object Tracking Vision System for Mapping the UCN τ Apparatus Volume

    Science.gov (United States)

    Lumb, Rowan; UCNtau Collaboration

    2016-09-01

    The UCN τ collaboration has an immediate goal to measure the lifetime of the free neutron to within 0.1%, i.e. about 1 s. The UCN τ apparatus is a magneto-gravitational ``bottle'' system. This system holds low energy, or ultracold, neutrons in the apparatus with the constraint of gravity, and keeps these low energy neutrons from interacting with the bottle via a strong 1 T surface magnetic field created by a bowl-shaped array of permanent magnets. The apparatus is wrapped with energized coils to supply a magnetic field throughout the ''bottle'' volume to prevent depolarization of the neutrons. An object-tracking stereo-vision system will be presented that precisely tracks a Hall probe and allows a mapping of the magnetic field throughout the volume of the UCN τ bottle. The stereo-vision system utilizes two cameras and open source openCV software to track an object's 3-d position in space in real time. The desired resolution is +/-1 mm resolution along each axis. The vision system is being used as part of an even larger system to map the magnetic field of the UCN τ apparatus and expose any possible systematic effects due to field cancellation or low field points which could allow neutrons to depolarize and possibly escape from the apparatus undetected. Tennessee Technological University.

  13. Human cerebral blood volume measurements using dynamic contrast enhancement in comparison to dynamic susceptibility contrast MRI

    Energy Technology Data Exchange (ETDEWEB)

    Artzi, Moran [Tel Aviv Sourasky Medical Center, Functional Brain Center, The Wohl Institute for Advanced Imaging, Tel Aviv (Israel); Tel Aviv University, Sackler Faculty of Medicine, Tel Aviv (Israel); Liberman, Gilad; Vitinshtein, Faina; Aizenstein, Orna [Tel Aviv Sourasky Medical Center, Functional Brain Center, The Wohl Institute for Advanced Imaging, Tel Aviv (Israel); Nadav, Guy [Tel Aviv Sourasky Medical Center, Functional Brain Center, The Wohl Institute for Advanced Imaging, Tel Aviv (Israel); Tel Aviv University, Faculty of Engineering, Tel Aviv (Israel); Blumenthal, Deborah T.; Bokstein, Felix [Tel Aviv Sourasky Medical Center, Neuro-Oncology Service, Tel Aviv (Israel); Bashat, Dafna Ben [Tel Aviv Sourasky Medical Center, Functional Brain Center, The Wohl Institute for Advanced Imaging, Tel Aviv (Israel); Tel Aviv University, Sackler Faculty of Medicine and Sagol School of Neuroscience, Tel Aviv (Israel)

    2015-07-15

    Cerebral blood volume (CBV) is an important parameter for the assessment of brain tumors, usually obtained using dynamic susceptibility contrast (DSC) MRI. However, this method often suffers from low spatial resolution and high sensitivity to susceptibility artifacts and usually does not take into account the effect of tissue permeability. The plasma volume (v{sub p}) can also be extracted from dynamic contrast enhancement (DCE) MRI. The aim of this study was to investigate whether DCE can be used for the measurement of cerebral blood volume in place of DSC for the assessment of patients with brain tumors. Twenty-eight subjects (17 healthy subjects and 11 patients with glioblastoma) were scanned using DCE and DSC. v{sub p} and CBV values were measured and compared in different brain components in healthy subjects and in the tumor area in patients. Significant high correlations were detected between v{sub p} and CBV in healthy subjects in the different brain components; white matter, gray matter, and arteries, correlating with the known increased tissue vascularity, and within the tumor area in patients. This work proposes the use of DCE as an alternative method to DSC for the assessment of blood volume, given the advantages of its higher spatial resolution, its lower sensitivity to susceptibility artifacts, and its ability to provide additional information regarding tissue permeability. (orig.)

  14. Measures of Autonomic Nervous System

    Science.gov (United States)

    2011-04-01

    Resiliency Model (TRM)* X* X* Trauma and Tension Releasing Exercises (TRE) Yoga (Asana) Postures X X Breathing Practices...MBSR) Yoga Nidra (iRest) X X *Study currently in progress utilizing these measures 7...measuring oxygen saturation of blood. The Doppler radar cardiopulmonary remote sensing unit and the wearable reflectance pulse oximeter have the benefit

  15. Relationship between testicular volume and testicular function: comparison of the Prader orchidometric and ultrasonographic measurements in patients with infertility

    Institute of Scientific and Technical Information of China (English)

    Hideo Sakamoto; Yoshio Ogawa; Hideki Yoshida

    2008-01-01

    Aim: To evaluate the relationship between testicular function and testicular volume measured by using Prader orchidometry and ultrasonography (US) to determine the critical testicular volume indicating normal testicular func-tion by each method. Methods: Total testicular volume (right plus left testicular volume) was measured in 794 testes in 397 men with infertility (mean age, 35.6 years) using a Prader orchidometer and also by ultrasonography.Ultrasonographic testicular volumes were calculated as length×width×height×0.71. To evaluate volume-function relationships, patients were divided into 10 groups representing 5-mL increments of total testicular volume by each method from below 10 mL to 50 mL or more. Results: Mean total testicular volume based on Prader orchidometry and US were 36.8 mL and 26.3 mL, respectively. Semen volume, sperm density, total sperm count, total motile sperm count, and serum FSH, LH, and testosterone all correlated significantly with total testicular volume measured by either method. Mean sperm density was in the oligozoospermic range in patients with total testicular volume below 35 mL by orchidometry or below 20 mL by ultrasonography. Mean total sperm count was subnormal in patients with total testicular volume below 30 mL by orchidometry or under 20 mL by ultrasonography. Conclusion: Testicular volume measured by either ultrasonography or Prader orchidometry correlated significantly with testicular function.However, critical total testicular volume indicating normal or nearly normal testicular function was 30 mL to 35 mL using Prader orchidometer and 20 mL using ultrasonography. Prader orchidometry morphometrically and function-ally overestimated the testicular volume in comparison to US.

  16. Portal blood flow volume measurement in schistosomal patients: evaluation of Doppler ultrasonography reproducibility

    Energy Technology Data Exchange (ETDEWEB)

    Leao, Alberto Ribeiro de Souza; Santos, Jose Eduardo Mourao; Moulin, Danilo Sales; Shigueoka, David Carlos; D' Ippolito, Giuseppe [Universidade Federal de Sao Paulo (UNIFESP/EPM), SP (Brazil). Escola Paulista de Medicina. Dept. de Diagnostico por Imagem]. E-mail: ar.leao@uol.com.br; Colleoni, Ramiro [Universidade Federal de Sao Paulo (UNIFESP/EPM), SP (Brazil). Escola Paulista de Medicina. Dept. de Gastroenterologia

    2008-09-15

    Objective: To evaluate the reproducibility of Doppler ultrasonography in the measurement of portal blood flow volume in schistosomal patients. Materials and methods: Prospective, transversal, observational and self-paired study evaluating 21 patients with hepatosplenic schistosomiasis submitted to Doppler ultrasonography performed by three independent observers for measurement of portal blood flow. Pairwise interobserver agreement was calculated by means of the intraclass correlation coefficient, paired t-test and Pearson's correlation coefficient. Results: Interobserver agreement was excellent. Intraclass correlation ranged from 80.6% to 93.0% (IC at 95% [65.3% ; 95.8%]), with the Pearson's correlation coefficient ranging between 81.6% and 92.7% with no statistically significant interobserver difference regarding the mean portal blood flow volume measured by Doppler ultrasonography (p = 0.954 / 0.758 / 0.749). Conclusion: Doppler ultrasonography has demonstrated to be a reliable method for measuring the portal blood flow volume in patients with portal hypertension secondary to schistosomiasis, with a good interobserver agreement. (author)

  17. Experimental Evaluation of the Applicability of Capacitive and Optical Measurement Methods for the Determination of Liquid Hydrogen Volume Flow

    Directory of Open Access Journals (Sweden)

    Gert HOLLER

    2009-08-01

    Full Text Available This paper presents a capacitive and a vision-based method for measuring the velocity of cryogenic hydrogen flows. The capacitive sensing principle exploits the spatial frequency signature of perturbations moving through a multi-electrode structure. This setup increases the sensitivity to dielectric permittivity variations compared to a simple two-electrode structure while preserving the ability to detect small perturbations. The vision-based method relies on a high-speed camera system that monitors the liquid hydrogen flow through an optical window yielding the flow velocity by cross-correlating subsequent images of the flow. Although a comprehensive analysis of the obtainable measurement uncertainty was not performed yet, current measurement results show the applicability of both principles for the non-invasive measurement of the volume flow of cryogenic fuels inside conveyor pipes.

  18. Volume Measurement Algorithm for Food Product with Irregular Shape using Computer Vision based on Monte Carlo Method

    Directory of Open Access Journals (Sweden)

    Joko Siswantoro

    2014-11-01

    Full Text Available Volume is one of important issues in the production and processing of food product. Traditionally, volume measurement can be performed using water displacement method based on Archimedes’ principle. Water displacement method is inaccurate and considered as destructive method. Computer vision offers an accurate and nondestructive method in measuring volume of food product. This paper proposes algorithm for volume measurement of irregular shape food product using computer vision based on Monte Carlo method. Five images of object were acquired from five different views and then processed to obtain the silhouettes of object. From the silhouettes of object, Monte Carlo method was performed to approximate the volume of object. The simulation result shows that the algorithm produced high accuracy and precision for volume measurement.

  19. On General Volume-Preserving Mechanical Systems via Cohomology

    Institute of Scientific and Technical Information of China (English)

    ZHOU Bin; GUO Han-Ying; WU Ke

    2003-01-01

    We present the general form of equations that generate a volume-preserving flow on a symplectic manifold(Μ,ω) via the highest Euler-Lagrange cohomology. It is shown that for every volume-preserving fiow there are some 2-forms that play a similar role to the Hamiltonian in the Hamilton mechanics and the ordinary canonical equations with Hamiltonian H are included as a special case with a 2-form Hω/(n - 1).

  20. Condition-dependent cell volume and concentration of Escherichia coli to facilitate data conversion for systems biology modeling

    NARCIS (Netherlands)

    Volkmer, Benjamin; Heinemann, Matthias

    2011-01-01

    Systems biology modeling typically requires quantitative experimental data such as intracellular concentrations or copy numbers per cell. In order to convert population-averaging omics measurement data to intracellular concentrations or cellular copy numbers, the total cell volume and number of cell

  1. Secondary School Mathematics, Chapter 15, The Real Number System, Chapter 16, Area, Volume, and Computation. Student's Text.

    Science.gov (United States)

    Stanford Univ., CA. School Mathematics Study Group.

    Topics covered in the first chapter of Unit 8 of this SMSG series include square roots, operations with radicals, operations with real numbers, and the structure of the real number system. The second chapter deals with measurement of area (for rectangular regions, other polygons, and circles), volume and surface area, computation involving…

  2. Measurement of atmospheric neutrino oscillations with very large volume neutrino telescopes

    CERN Document Server

    Yañez, J P

    2015-01-01

    Neutrino oscillations have been probed during the last few decades using multiple neutrino sources and experimental set-ups. In the recent years, very large volume neutrino telescopes have started contributing to the field. First ANTARES and then IceCube have relied on large and sparsely instrumented volumes to observe atmospheric neutrinos for combinations of baselines and energies inaccessible to other experiments. Using this advantage, the latest result from IceCube starts approaching the precision of other established technologies, and is paving the way for future detectors, such as ORCA and PINGU. These new projects seek to provide better measurements of neutrino oscillation parameters, and eventually determine the neutrino mass ordering. The results from running experiments and the potential from proposed projects are discussed in this review, emphasizing the experimental challenges involved in the measurements.

  3. Automated digital volume measurement of melanoma metastases in sentinel nodes predicts disease recurrence and survival

    DEFF Research Database (Denmark)

    Riber-Hansen, Rikke; Nyengaard, Jens R; Hamilton-Dutoit, Stephen J

    2011-01-01

    aim was to investigate whether digital image analysis can estimate TMV accurately in melanoma SLNs. Methods and results: TMV was measured in 147 SLNs from 95 patients both manually and by automated digital image analysis. The results were compared by Bland-Altman plots (numerical data) and kappa......Aims: Total metastatic volume (TMV) is an important prognostic factor in melanoma sentinel lymph nodes (SLNs) that avoids both the interobserver variation and unidirectional upstaging seen when using semi-quantitative size estimates. However, it is somewhat laborious for routine application. Our...... statistics (categorical data). In addition, disease-free and melanoma-specific survivals were calculated. Mean metastatic volume per patient was 10.6 mm(3) (median 0.05 mm(3); range 0.0001-621.3 mm(3)) and 9.62 mm(3) (median 0.05 mm(3); range 0.00001-564.3 mm(3)) with manual and digital measurement...

  4. Measurement of Atmospheric Neutrino Oscillations with Very Large Volume Neutrino Telescopes

    Directory of Open Access Journals (Sweden)

    J. P. Yáñez

    2015-01-01

    Full Text Available Neutrino oscillations have been probed during the last few decades using multiple neutrino sources and experimental set-ups. In the recent years, very large volume neutrino telescopes have started contributing to the field. First ANTARES and then IceCube have relied on large and sparsely instrumented volumes to observe atmospheric neutrinos for combinations of baselines and energies inaccessible to other experiments. Using this advantage, the latest result from IceCube starts approaching the precision of other established technologies and is paving the way for future detectors, such as ORCA and PINGU. These new projects seek to provide better measurements of neutrino oscillation parameters and eventually determine the neutrino mass ordering. The results from running experiments and the potential from proposed projects are discussed in this review, emphasizing the experimental challenges involved in the measurements.

  5. Dynamic measures of regional lung air volume using phase contrast x-ray imaging

    Energy Technology Data Exchange (ETDEWEB)

    Kitchen, M J; Lewis, R A; Morgan, M J; Siu, K K W; Habib, A [School of Physics, Monash University, Melbourne VIC 3800 (Australia); Wallace, M J; Siew, M L; Hooper, S B [Department of Physiology, Monash University, Melbourne VIC 3800 (Australia); Fouras, A [Division of Biological Engineering, Monash University, Melbourne VIC 3800 (Australia); Yagi, N; Uesugi, K [SPring-8/JASRI, Sayo, Hyogo 679-5198 (Japan)], E-mail: Marcus.Kitchen@sci.monash.edu.au

    2008-11-07

    Phase contrast x-ray imaging can provide detailed images of lung morphology with sufficient spatial resolution to observe the terminal airways (alveoli). We demonstrate that quantitative functional and anatomical imaging of lung ventilation can be achieved in vivo using two-dimensional phase contrast x-ray images with high contrast and spatial resolution (<100 {mu}m) in near real time. Changes in lung air volume as small as 25 {mu}L were calculated from the images of term and preterm rabbit pup lungs (n = 28) using a single-image phase retrieval algorithm. Comparisons with plethysmography and computed tomography showed that the technique provided an accurate and robust method of measuring total lung air volumes. Furthermore, regional ventilation was measured by partitioning the phase contrast images, which revealed differences in aeration for different ventilation strategies.

  6. Metabolic tumour volumes measured at staging in lymphoma: methodological evaluation on phantom experiments and patients

    Energy Technology Data Exchange (ETDEWEB)

    Meignan, Michel [Hopital Henri Mondor and Paris-Est University, Department of Nuclear Medicine, Creteil (France); Paris-Est University, Service de Medecine Nucleaire, EAC CNRS 7054, Hopital Henri Mondor AP-HP, Creteil (France); Sasanelli, Myriam; Itti, Emmanuel [Hopital Henri Mondor and Paris-Est University, Department of Nuclear Medicine, Creteil (France); Casasnovas, Rene Olivier [CHU Le Bocage, Department of Hematology, Dijon (France); Luminari, Stefano [University of Modena and Reggio Emilia, Department of Diagnostic, Clinic and Public Health Medicine, Modena (Italy); Fioroni, Federica [Santa Maria Nuova Hospital-IRCCS, Department of Medical Physics, Reggio Emilia (Italy); Coriani, Chiara [Santa Maria Nuova Hospital-IRCCS, Department of Radiology, Reggio Emilia (Italy); Masset, Helene [Henri Mondor Hospital, Department of Radiophysics, Creteil (France); Gobbi, Paolo G. [University of Pavia, Department of Internal Medicine and Gastroenterology, Fondazione IRCCS Policlinico San Matteo, Pavia (Italy); Merli, Francesco [Santa Maria Nuova Hospital-IRCCS, Department of Hematology, Reggio Emilia (Italy); Versari, Annibale [Santa Maria Nuova Hospital-IRCCS, Department of Nuclear Medicine, Reggio Emilia (Italy)

    2014-06-15

    The presence of a bulky tumour at staging on CT is an independent prognostic factor in malignant lymphomas. However, its prognostic value is limited in diffuse disease. Total metabolic tumour volume (TMTV) determined on {sup 18}F-FDG PET/CT could give a better evaluation of the total tumour burden and may help patient stratification. Different methods of TMTV measurement established in phantoms simulating lymphoma tumours were investigated and validated in 40 patients with Hodgkin lymphoma and diffuse large B-cell lymphoma. Data were processed by two nuclear medicine physicians in Reggio Emilia and Creteil. Nineteen phantoms filled with {sup 18}F-saline were scanned; these comprised spherical or irregular volumes from 0.5 to 650 cm{sup 3} with tumour-to-background ratios from 1.65 to 40. Volumes were measured with different SUVmax thresholds. In patients, TMTV was measured on PET at staging by two methods: volumes of individual lesions were measured using a fixed 41 % SUVmax threshold (TMTV{sub 41}) and a variable visually adjusted SUVmax threshold (TMTV{sub var}). In phantoms, the 41 % threshold gave the best concordance between measured and actual volumes. Interobserver agreement was almost perfect. In patients, the agreement between the reviewers for TMTV{sub 41} measurement was substantial (ρ {sub c} = 0.986, CI 0.97 - 0.99) and the difference between the means was not significant (212 ± 218 cm{sup 3} for Creteil vs. 206 ± 219 cm{sup 3} for Reggio Emilia, P = 0.65). By contrast the agreement was poor for TMTV{sub var}. There was a significant direct correlation between TMTV{sub 41} and normalized LDH (r = 0.652, CI 0.42 - 0.8, P <0.001). Higher disease stages and bulky tumour were associated with higher TMTV{sub 41}, but high TMTV{sub 41} could be found in patients with stage 1/2 or nonbulky tumour. Measurement of baseline TMTV in lymphoma using a fixed 41% SUVmax threshold is reproducible and correlates with the other parameters for tumour mass evaluation

  7. Validation of a continuous penile blood-flow measurement by pulse-volume-plethysmography.

    Science.gov (United States)

    Lavoisier, P; Barbe, R; Gally, M

    2002-04-01

    Today, in the assessment of cavernous artery blood-flow, the most commonly used technique is Doppler ultrasound velocimetry (continuous, pulsed, color-coded or power), which is often considered as the gold standard. Plethysmographic techniques and radioactive tracers have been widely used for the assessment of global penis flow variations but are not adequate for continuous blood-flow measurement. A new pulse-volume plethysmographic (PVP) device using a water-filled penile cuff was employed to assess continuous blood-flow measurement in the penis. Simultaneously Doppler velocity was recorded and served as a gold standard. A penile water-cuff is connected through a pressure tube to a three-way tap. The pulse-volume changes in the penile water-cuff are measured by means of a latex membrane placed over one of the three-way taps. The displacements of the latex are recorded by a photoplethysmograph. The third tap is connected to a 5 l perfusion bag placed 30 cm above the penis so as to maintain constant pressure in the whole device whatever the penis volume. Twenty-four volunteers were tested. The Doppler velocity signal and pulse volume of cavernous arteries were measured simultaneously after PGE1 intra-cavernous injection. Blood-flow variations were induced by increasing penis artery compression with a second penile water-cuff used as a tourniquet fitted onto the penis root, and the pressure of which could be modified by a water-filled syringe. The amplitude of the plethysmographic pulse-volume signal and the area under the Doppler velocity signal were correlated. The inter-patient (n=24) correlation ranged from 0.455 to 0.904, with a mean correlation of 0.704 and P<0.0001. PVP measurement by a water-filled cuff was validated by ultrasound velocimetry. This new continuous, non-invasive and easy-to-use technique enables physiological and physiopathological flow-measurement during sleep, under visual sexual stimulation (VSS), or following artificial erection

  8. Introduction to control system performance measurements

    CERN Document Server

    Garner, K C

    1968-01-01

    Introduction to Control System Performance Measurements presents the methods of dynamic measurements, specifically as they apply to control system and component testing. This book provides an introduction to the concepts of statistical measurement methods.Organized into nine chapters, this book begins with an overview of the applications of automatic control systems that pervade almost every area of activity ranging from servomechanisms to electrical power distribution networks. This text then discusses the common measurement transducer functions. Other chapters consider the basic wave

  9. Know your tools - concordance of different methods for measuring brain volume change after ischemic stroke

    Energy Technology Data Exchange (ETDEWEB)

    Yassi, Nawaf; Campbell, Bruce C.V.; Davis, Stephen M.; Bivard, Andrew [The University of Melbourne, Departments of Medicine and Neurology, Melbourne Brain Centre rate at The Royal Melbourne Hospital, Parkville, Victoria (Australia); Moffat, Bradford A.; Steward, Christopher; Desmond, Patricia M. [The University of Melbourne, Department of Radiology, The Royal Melbourne Hospital, Parkville (Australia); Churilov, Leonid [The University of Melbourne, The Florey Institute of Neurosciences and Mental Health, Parkville (Australia); Parsons, Mark W. [University of Newcastle and Hunter Medical Research Institute, Priority Research Centre for Translational Neuroscience and Mental Health, Newcastle (Australia)

    2015-07-15

    Longitudinal brain volume changes have been investigated in a number of cerebral disorders as a surrogate marker of clinical outcome. In stroke, unique methodological challenges are posed by dynamic structural changes occurring after onset, particularly those relating to the infarct lesion. We aimed to evaluate agreement between different analysis methods for the measurement of post-stroke brain volume change, and to explore technical challenges inherent to these methods. Fifteen patients with anterior circulation stroke underwent magnetic resonance imaging within 1 week of onset and at 1 and 3 months. Whole-brain as well as grey- and white-matter volume were estimated separately using both an intensity-based and a surface watershed-based algorithm. In the case of the intensity-based algorithm, the analysis was also performed with and without exclusion of the infarct lesion. Due to the effects of peri-infarct edema at the baseline scan, longitudinal volume change was measured as percentage change between the 1 and 3-month scans. Intra-class and concordance correlation coefficients were used to assess agreement between the different analysis methods. Reduced major axis regression was used to inspect the nature of bias between measurements. Overall agreement between methods was modest with strong disagreement between some techniques. Measurements were variably impacted by procedures performed to account for infarct lesions. Improvements in volumetric methods and consensus between methodologies employed in different studies are necessary in order to increase the validity of conclusions derived from post-stroke cerebral volumetric studies. Readers should be aware of the potential impact of different methods on study conclusions. (orig.)

  10. On-chip acidification rate measurements from single cardiac cells confined in sub-nanoliter volumes

    OpenAIRE

    Ges, Igor A.; Dzhura, Igor A.; Baudenbacher, Franz J.

    2008-01-01

    The metabolic activity of cells can be monitored by measuring the pH in the extracellular environment. Microfabrication and microfluidic technologies allow the sensor size and the extracellular volumes to be comparable to single cells. A glass substrate with thin film pH sensitive IrOx electrodes was sealed to a replica-molded polydimethylsiloxane (PDMS) microfluidic network with integrated valves. The device, termed NanoPhysiometer, allows the trapping of single cardiac myocytes and the meas...

  11. 64排螺旋 CT 及三维容积测量系统对肺叶容积的定量研究%The quantitative measurement of pulmonary lobar volume using 3-dimensional volumetric diagnosis system and 64 row MDCT

    Institute of Scientific and Technical Information of China (English)

    刘斋; 何丽; 贾立镯; 任庆云

    2016-01-01

    Objective To explore the value of 3‐dimensional volumetric diagnosis system in quantitative measurement of pulmona‐ry lobar volumetry using a 64 row MDCT .Methods Seventy‐seven adult volunteers were scanned twice on a 64 row MDCT at the end of the maximum inspiratory and maximum expiratory end respectively .On a volumetric computer‐aided diagnosis system ,the en‐tire lung was semiautomatically separated into 5 anatomy lobes including the right upper lobe ,right middle lobe ,right lower lobe ,left upper lobe ,and left lower lobe .Each lobar volume was measured .Results The lung volume of left upper lobe ,right lower lobe ,left lower lobe ,right upper lobe ,right middle lobe in male volunteers were 1 303 .90 mL and 938 .31 mL ,1 276 .90 mL and 737 .69 mL , 1 204 .47 mL and 678 .67 mL ,1 048 .49 mL and 754 .83 mL ,519 .53 mL and 407 .86 mL at the end of the inspiratory and expiratory respectively .The lung volume of left upper lobe ,right lower lobe ,left lower lobe ,right upper lobe ,right middle lobe in female volun‐teers were 915 .78 mL and 666 .23 mL ,913 .87 mL and 576 .62 mL ,822 .17 mL and 509 .30 mL ,734 .20 mL and 530 .23 mL ,389 .13 mL and 316 .70 mL at the end of the inspiratory and expiratory respectively .The values of each lobe volume between the full inspiration phase and expiration phase group showed significant difference the same sex group (P<0 .05) .The values of each lobe volume in the man group were significantly larger than those of female group in both respiratory phase (P<0 .05) .Of the D‐value in the each lobe volume in 5 anatomy lobe at full inspiration phase and expiration phase in both sex group ,both of the lower lobes were the largest , followed by the left upper lobe ,right upper lobe and right middle lobe .The D‐value in the each lobe volume at full inspiration phase and expiration phase in the man group were significantly larger than those of female group .Conclusion Three‐dimensional volumet‐ric diagnosis system

  12. Measurement of fluid viscosity at microliter volumes using quartz impedance analysis.

    Science.gov (United States)

    Saluja, Atul; Kalonia, Devendra S

    2004-08-05

    The purpose of this work was to measure viscosity of fluids at low microliter volumes by means of quartz crystal impedance analysis. To achieve this, a novel setup was designed that allowed for measurement of viscosity at volumes of 8 to 10 microL. The technique was based on the principle of electromechanical coupling of piezoelectric quartz crystals. The arrangement was simple with measurement times ranging from 2 to 3 minutes. The crystal setup assembly did not impose any unwanted initial stress on the unloaded quartz crystal. Quartz crystals of 5- and 10-MHz fundamental frequency were calibrated with glycerol-water mixtures of known density and viscosity prior to viscosity measurements. True frequency shifts, for the purpose of this work, were determined followed by viscosity measurement of aqueous solutions of sucrose, urea, PEG-400, glucose, and ethylene glycol at 25 degrees C +/- 0.5 degrees C. The measured viscosities were found to be reproducible and consistent with the values reported in the literature. Minor inconsistencies in the measured resistance and frequency shifts did not affect the results significantly, and were found to be experimental in origin rather than due to electrode surface roughness. Besides, as expected for a viscoelastic fluid, PEG 8000 solutions, the calculated viscosities were found to be less than the reported values due to frequency dependence of storage and loss modulus components of complex viscosity. From the results, it can be concluded that the present setup can provide accurate assessment of viscosity of Newtonian fluids and also shows potential for analyzing non-Newtonian fluids at low microliter volumes.

  13. Should ascitis volume and anthropometric measurements be estimated in hospitalized alcoholic cirrotics?

    Directory of Open Access Journals (Sweden)

    E. M. Silva

    2012-12-01

    Full Text Available Introduction: Ascitis and undernutrition are frequent complications of cirrhosis, however ascitis volume and anthropometric assessment are not routinely documented or considered in prognostic evaluation. In a homogeneous cohort followed during two years these variables were scrutinized, aiming to ascertain relevance for longterm outcome. Methods: Population (N = 25, all males with alcoholic cirrhosis was recruited among patients hospitalized for uncomplicated ascitis. Exclusion criteria were refractory or tense ascitis, cancer, spontaneous bacterial peritonitis, bleeding varices and critical illness. Measurements included ultrasonographically estimated ascitis volume, dry body mass index/BMI , upper arm anthropometrics, hematologic counts and liver function tests. Results: Population (age 48.3 ± 11.3 years, BMI 21.1± 3.5 kg/m², serum albumin 2.5 ± 0.8 g/dL was mostly in the Child-Pugh C category (77.8% but clinically stable. During the follow-up period of 22.6 ±3.8 months, additional hospitalizations numbered 1.7 ± 1.0 and more than one quarter succumbed. Admission ascitis volume corresponded to 7.1 ± 3.6 L and dry BMI to 18.3 ± 3.5 kg/m². Child Pugh index was relevant for both mortality and rehospitalization. Nevertheless, similar matches for mortality were documented with ascitis volume and dry BMI, and arm circumference below the 5th percentile was highly significantly associated with rehospitalization. Conclusions: A greater association than hitherto acknowledged, between ascitis volume and anthropometric measurements from one side, and long-term rehospitalization and mortality from the other, was demonstrated in male stable alcoholic cirrhotics. Further studies with alcoholic and other modalities of cirrhosis including women are recommended.

  14. Low Temperature Emissivity Measurement System

    Directory of Open Access Journals (Sweden)

    Jignesh A. Patel

    2014-05-01

    Full Text Available The emissivity of a material is the relative ability of its surface to emit energy by radiation. It is the ratio of energy radiated by a particular material to energy radiated by a black body at the same temperature. Knowledge about the low temperature emissivity of materials and coatings can be essential to the design of fusion cryoplants and in the thermal modeling for space satellite missions. The emittance of materials at cryogenics temperatures often cannot be predicted from room temperature data, but for computing radiative loads and infrared backgrounds this cryogenic data is often required. Measurement of the cryogenic emissivity of a highly reflective surface is a significant challenge: little thermal power is radiated from the sample, and the background radiation. However some researchers have measured emissivity at various low temperature ranges. Present work reports, the various emissivity measurement setup and their considerations.

  15. Reproducibility of techniques using Archimedes' principle in measuring cancellous bone volume.

    Science.gov (United States)

    Zou, L; Bloebaum, R D; Bachus, K N

    1997-01-01

    Researchers have been interested in developing techniques to accurately and reproducibly measure the volume fraction of cancellous bone. Historically bone researchers have used Archimedes' principle with water to measure the volume fraction of cancellous bone. Preliminary results in our lab suggested that the calibrated water technique did not provide reproducible results. Because of this difficulty, it was decided to compare the conventional water method to a water with surfactant and a helium method using a micropycnometer. The water/surfactant and the helium methods were attempts to improve the fluid penetration into the small voids present in the cancellous bone structure. In order to compare the reproducibility of the new methods with the conventional water method, 16 cancellous bone specimens were obtained from femoral condyles of human and greyhound dog femora. The volume fraction measurements on each specimen were repeated three times with all three techniques. The results showed that the helium displacement method was more than an order of magnitudes more reproducible than the two other water methods (p < 0.05). Statistical analysis also showed that the conventional water method produced the lowest reproducibility (p < 0.05). The data from this study indicate that the helium displacement technique is a very useful, rapid and reproducible tool for quantitatively characterizing anisotropic porous tissue structures such as cancellous bone.

  16. Linear and volume measurements of pulmonary nodules at different CT dose levels. Interscan and interscan analysis

    Energy Technology Data Exchange (ETDEWEB)

    Hein, P.A.; Romano, V.C.; Rogalla, P.; Klessen, C.; Lembcke, A.; Bauknecht, H.C. [Charite-Universitaetsmedizin Berlin (Germany). Inst. fuer Radiologie; Dicken, V.; Bornemann, L. [MeVis Research, Bremen (Germany)

    2009-01-15

    Purpose: To compare the interobserver variability of the unidimensional diameter and volume measurements of pulmonary nodules in an intrascan and interscan analysis using semi-automated segmentation software on ultra-low-dose computed tomography (ULD-CT) and standard dose CT (SD-CT) data. Materials and Methods: In 33 patients with pulmonary nodules, two chest multi-slice CT (MSCT) datasets (1 mm slice thickness; 20 % reconstruction overlap) had been consecutively acquired with an ultra-low dose (120 kV, 5 mAs) and standard dose technique (120 kV, 75 mAs). MSCT data was retrospectively analyzed using the segmentation software OncoTREAT (MeVis, Bremen, Germany, version 1.3). The volume of 229 solid pulmonary nodules included in the analysis as well as the largest diameter according to RECIST (Response Evaluation Criteria for Solid Tumors) were measured by two radiologists. Interobserver variability was calculated and SD-CT and ULD-CT data compared in an intrascan and interscan analysis. Results: The median nodule diameter (n = 229 nodules) was registered with 8.2 mm (range: 2.8 to 43.6 mm, mean: 10.8 mm). The nodule volume ranged between 0.01 and 49.1 ml (median 0.1 ml, mean 1.5 ml). With respect to interobserver variability, the intrascan analysis did not reveal statistically significant differences (p > 0.05) between ULD-CT and SD-CT with broader limits of agreement for relative differences of RECIST measurements (-31.0 % + 27.0 % mean -2.0 % for SD-CT; -27.0 % + 38.6 %, mean 5.8 % for ULD-CT) than for volume measurements (-9.4 %, 8.0 %, mean 0.7 % for SD-CT; -13 %, 13 %, mean 0.0 % for ULD-CT). The interscan analysis showed broadened 95 % confidence intervals for volume measurements (-26.5 % 29.1 % mean 1.3 %, and -25.2 %, 29.6 %, mean 2.2 %) but yielded comparable limits of agreement for RECIST measurements. Conclusion: The variability of nodule volumetry assessed by semi-automated segmentation software as well as nodule size determination by RECIST appears to be

  17. TFaNS Tone Fan Noise Design/Prediction System. Volume 1; System Description, CUP3D Technical Documentation and Manual for Code Developers

    Science.gov (United States)

    Topol, David A.

    1999-01-01

    TFaNS is the Tone Fan Noise Design/Prediction System developed by Pratt & Whitney under contract to NASA Lewis (presently NASA Glenn). The purpose of this system is to predict tone noise emanating from a fan stage including the effects of reflection and transmission by the rotor and stator and by the duct inlet and nozzle. These effects have been added to an existing annular duct/isolated stator noise prediction capability. TFaNS consists of: The codes that compute the acoustic properties (reflection and transmission coefficients) of the various elements and write them to files. Cup3D: Fan Noise Coupling Code that reads these files, solves the coupling problem, and outputs the desired noise predictions. AWAKEN: CFD/Measured Wake Postprocessor which reformats CFD wake predictions and/or measured wake data so it can be used by the system. This volume of the report provides technical background for TFaNS including the organization of the system and CUP3D technical documentation. This document also provides information for code developers who must write Acoustic Property Files in the CUP3D format. This report is divided into three volumes: Volume I: System Description, CUP3D Technical Documentation, and Manual for Code Developers; Volume II: User's Manual, TFaNS Vers. 1.4; Volume III: Evaluation of System Codes.

  18. Usefulness and limitation of punched-out orchidometer in testicular volume measurement

    Institute of Scientific and Technical Information of China (English)

    Koji Shiraishi; Hiroshi Takihara; Yoriaki Kamiryo; Katsusuke Naito

    2005-01-01

    Aim: To determine the limitations of a punched-out orchidometer in practical use, we compared with a scrotal ultrasound (USG). Methods: A total of 281 testes from 142 males were examined using both a punched-out orchidometer and a USG. The volume differential between both methods was calculated and expressed as orchidometer/USG volume (O/U ratio). Distribution of the O/U ratio was determined and subdivided by clinical or pathological diagnosis. The correlations between the O/U ratio and patient age or orchidometer results were assessed. Results:There was a significant linear relationship between the results of orchidometer and USG (r = 0.94, P < 0.0001). The relationship between the O/U ratio and age or testicular volumes showed significant inverse correlations (r = 0.22,P = 0.0002, r = 0.45, P<0.0001, respectively). Klinefelter's syndrome, ipsilateral detorted testes and hypogonadotropic hypogonadism comparatively showed a high O/U ratio. No incidental lesion was detected by USG necessitating treatment. Conclusion: The punched-out orchidometer gives estimates that correlated well with the USG measurements and provides enough information for routine andrological evaluation. We should be aware that the orchidometer often overestimates the testicular volume, especially for the patients with small testis or adolescents.

  19. Measurement of track structure parameters of low and medium energy helium and carbon ions in nanometric volumes

    Science.gov (United States)

    Hilgers, G.; Bug, M. U.; Rabus, H.

    2017-10-01

    Ionization cluster size distributions produced in the sensitive volume of an ion-counting wall-less nanodosimeter by monoenergetic carbon ions with energies between 45 MeV and 150 MeV were measured at the TANDEM-ALPI ion accelerator facility complex of the LNL-INFN in Legnaro. Those produced by monoenergetic helium ions with energies between 2 MeV and 20 MeV were measured at the accelerator facilities of PTB and with a 241Am alpha particle source. C3H8 was used as the target gas. The ionization cluster size distributions were measured in narrow beam geometry with the primary beam passing the target volume at specified distances from its centre, and in broad beam geometry with a fan-like primary beam. By applying a suitable drift time window, the effective size of the target volume was adjusted to match the size of a DNA segment. The measured data were compared with the results of simulations obtained with the PTB Monte Carlo code PTra. Before the comparison, the simulated cluster size distributions were corrected with respect to the background of additional ionizations produced in the transport system of the ionized target gas molecules. Measured and simulated characteristics of the particle track structure are in good agreement for both types of primary particles and for both types of the irradiation geometry. As the range in tissue of the ions investigated is within the typical extension of a spread-out Bragg peak, these data are useful for benchmarking not only ‘general purpose’ track structure simulation codes, but also treatment planning codes used in hadron therapy. Additionally, these data sets may serve as a data base for codes modelling the induction of radiation damages at the DNA-level as they almost completely characterize the ionization component of the nanometric track structure.

  20. Image quality simulation and verification of x-ray volume imaging systems

    Science.gov (United States)

    Kroon, Han; Schoumans, Nicole; Snoeren, Ruud

    2006-03-01

    Nowadays, 2D X-ray systems are used more and more for 3-dimensional rotational X-ray imaging (3D-RX) or volume imaging, such as 3D rotational angiography. However, it is not evident that the application of settings for optimal 2D images also guarantee optimal conditions for 3D-RX reconstruction results. In particular the search for a good compromise between patient dose and IQ may lead to different results in case of 3D imaging. For this purpose we developed an additional 3D-RX module for our full-scale image quality & patient dose (IQ&PD) simulation model, with specific calculations of patient dose under rotational conditions, and contrast, sharpness and noise of 3D images. The complete X-ray system from X-ray tube up to and including the display device is modelled in separate blocks for each distinguishable component or process. The model acts as a tool for X-ray system design, image quality optimisation and patient dose reduction. The model supports the decomposition of system level requirements, and takes inherently care of the prerequisite mutual coherence between component requirements. The short calculation times enable comprehensive multi-parameter optimisation studies. The 3D-RX IQ&PD performance is validated by comparing calculation results with actual measurements performed on volume images acquired with a state-of-the-art 3D-RX system. The measurements include RXDI dose index, signal and contrast based on Hounsfield units (H and ΔH), modulation transfer function (MTF), noise variance (σ2) and contrast-to-noise ratio (CNR). Further we developed a new 3D contrast-delta (3D-CΔ) phantom with details of varying size and contrast medium material and concentration. Simulation and measurement results show a significant correlation.

  1. Breathing detection with a portable impedance measurement system: first measurements.

    Science.gov (United States)

    Cordes, Axel; Foussier, Jerome; Leonhardt, Steffen

    2009-01-01

    For monitoring the health status of individuals, detection of breathing and heart activity is important. From an electrical point of view, it is known that breathing and heart activity change the electrical impedance distribution in the human body over the time due to ventilation (high impedance) and blood shifts (low impedance). Thus, it is possible to detect both important vital parameters by measuring the impedance of the thorax or the region around lung and heart. For some measurement scenarios it is also essential to detect these parameters contactless. For instance, monitoring bus drivers health could help to limit accidents, but directly connected systems limit the drivers free moving space. One measurement technology for measuring the impedance changes in the chest without cables is the magnetic impedance tomography (MIT). This article describes a portable measurement system we developed for this scenario that allows to measure breathing contactless. Furthermore, first measurements with five volunteers were performed and analyzed.

  2. CT-measured regional specific volume change reflects regional ventilation in supine sheep.

    Science.gov (United States)

    Fuld, Matthew K; Easley, R Blaine; Saba, Osama I; Chon, Deokiee; Reinhardt, Joseph M; Hoffman, Eric A; Simon, Brett A

    2008-04-01

    Computer tomography (CT) imaging techniques permit the noninvasive measurement of regional lung function. Regional specific volume change (sVol), determined from the change in lung density over a tidal breath, should correlate with regional ventilation and regional lung expansion measured with other techniques. sVol was validated against xenon (Xe)-CT-specific ventilation (sV) in four anesthetized, intubated, mechanically ventilated sheep. Xe-CT used expiratory gated axial scanning during the washin and washout of 55% Xe. sVol was measured from the tidal changes in tissue density (H, houndsfield units) of lung regions using the relationship sVol = [1,000(Hi - He)]/[He(1,000 + Hi)], where He and Hi are expiratory and inspiratory regional density. Distinct anatomical markings were used to define corresponding lung regions of interest between inspiratory, expiratory, and Xe-CT images, with an average region of interest size of 1.6 +/- 0.7 ml. In addition, sVol was compared with regional volume changes measured directly from the positions of implanted metal markers in an additional animal. A linear relationship between sVol and sV was demonstrated over a wide range of regional sV found in the normal supine lung, with an overall correlation coefficient (R(2)) of 0.66. There was a tight correlation (R(2) = 0.97) between marker-measured volume changes and sVol. Regional sVol, which involves significantly reduced exposure to radiation and Xe gas compared with the Xe-CT method, represents a safe and efficient surrogate for measuring regional ventilation in experimental studies and patients.

  3. System 80+{trademark} Standard Design: CESSAR design certification. Volume 2: Amendment I

    Energy Technology Data Exchange (ETDEWEB)

    1990-12-21

    This report, entitled Combustion Engineering Standard Safety Analysis Report - Design Certification (CESSAR-DC), has been prepared in support of the industry effort to standardize nuclear plant designs. These documents describe the Combustion Engineering, Inc. System 80+{sup TM} Standard Design. This report, Volume 2, in conjunction with Volume 3, provides the design of structures, components, equipment and systems.

  4. System 80+{trademark} Standard Design: CESSAR design certification. Volume 3: Amendment I

    Energy Technology Data Exchange (ETDEWEB)

    1990-12-21

    This report, entitled Combustion Engineering Standard Safety Analysis Report - Design Certification (CESSAR-DC), has been prepared in support of the industry effort to standardize nuclear plant designs. These documents describe the Combustion Engineering, Inc. System 80+{sup TM} Standard Design. This report, Volume 3, in conjunction with Volume 2, provides the design of structures, components, equipment and systems.

  5. System 80+{trademark} Standard Design: CESSAR design certification. Volume 10: Amendment I

    Energy Technology Data Exchange (ETDEWEB)

    1990-12-21

    This report, entitled Combustion Engineering Standard Safety Analysis Report -- Design Certification (CESSAR-DC), has been prepared in support of the industry effort to standardize nuclear plant designs. These volumes describe the Combustion Engineering, Inc. System 80{sup +}{trademark} Standard Design. This volume 10 discusses the Steam and Power Conversion System and Radioactive Waste Management.

  6. The Del Mod System: An External Evaluation, Final Report, Volume IV.

    Science.gov (United States)

    Humphreys, Donald W.; And Others

    This is one of five volumes prepared to describe various aspects of the Del Mod System. This volume deals with the evaluation of the Del Mod System. Included are the following: (1) Del Mod Responsive Evaluation; (2) Evaluation Outcomes; (3) Validation of the Del Mod Responsive Evaluation Process; and (4) Conclusions. Appendices include: (A)…

  7. A water-renewal system that accurately delivers small volumes of water to exposure chambers

    Science.gov (United States)

    Zumwalt, D. C.; Dwyer, F.J.; Greer, I.E.; Ingersoll, C.G.

    1994-01-01

    This paper describes a system that can accurately deliver small volumes of water (50 ml per cycle) to eight 300-ml beakers. The system is inexpensive <$100), easy to build (<8 h), and easy to calibrate (<15 min), and accurately delivers small volumes of water (<5% variability).

  8. System 80+{trademark} Standard Design: CESSAR design certification. Volume 9: Amendment I

    Energy Technology Data Exchange (ETDEWEB)

    1990-12-21

    This report, entitled Combustion Engineering Standard Safety Analysis Report -- Design Certification (CESSAR-DC), has been prepared in support of the industry effort to standardize nuclear plant designs. These volumes describe the Combustion Engineering, Inc. System 80{sup +}{trademark} Standard Design. This volume 9 discusses Electric Power and Auxiliary Systems.

  9. Volume monogamy of quantum steering ellipsoids for multiqubit systems

    Science.gov (United States)

    Cheng, Shuming; Milne, Antony; Hall, Michael J. W.; Wiseman, Howard M.

    2016-10-01

    The quantum steering ellipsoid can be used to visualize 2-qubit states, and thus provides a generalization of the Bloch picture for the single qubit. Recently, a monogamy relation for the volumes of steering ellipsoids has been derived for pure 3-qubit states and shown to be stronger than the celebrated Coffman-Kundu-Wootters inequality. We first demonstrate the close connection between this volume monogamy relation and the classification of pure 3-qubit states under stochastic local operations and classical communication. We then show that this monogamy relation does not hold for general mixed 3-qubit states and derive a weaker monogamy relation that does hold for such states. We also prove a volume monogamy relation for pure 4-qubit states (further conjectured to hold for the mixed case), and generalize our 3-qubit inequality to n qubits. Finally, we study the effect of noise on the quantum steering ellipsoid and find that the volume of any 2-qubit state is nonincreasing when the state is exposed to arbitrary local noise. This implies that any volume monogamy relation for a given class of multiqubit states remains valid under the addition of local noise. We investigate this quantitatively for the experimentally relevant example of isotropic noise.

  10. Static contact angle measurement at different volumes of a drop sitting on non-ferrous metals

    OpenAIRE

    Feoktistov Dmitriy; Orlova Evgeniya; Batischeva Kseniya; Semenov Andrey

    2016-01-01

    The paper presents the experimental study of the effect of the liquid volume on the static contact angle under the condition of the stationary contact line on the rough and polished surfaces of non-ferrous metals. The experiments were carried out using the shadow optical system. Comparison between two methods of drop profile processing was conducted. It was found that in addition to the friction and gravity forces, the structure of the non-ferrous metals significantly influence on the static ...

  11. Capillary method for measuring near-infrared spectra of microlitre volume liquids

    Institute of Scientific and Technical Information of China (English)

    YUAN Bo; MURAYAMA Koichi

    2007-01-01

    The present study theoretically explored the feasibility of the capillary method for measuring near-infrared (NIR) spectra of liquid or solution samples with microlitre volume, which was proposed in our previous studies. Lambert-Beer absorbance rule was applied to establish a model for the integral absorbance of capillary, which was then implemented in numerical analyses of the effects of capillary on various spectral features and dynamic range of absorption measurement. The theoretical speculations indicated that the capillary method might be used in NIR spectroscopy, which was further supported by the empirical data collected from our experiments by comparison between capillary NIR spectra of several organic solvents and cuvette cell NIR spectra.

  12. Noninvasive Intracranial Volume and Pressure Measurements Using Ultrasound (Head and Spinal)

    Science.gov (United States)

    Hargens, Alan R.

    1999-01-01

    Prevention of secondary brain injuries following head trauma can be accomplished most easily when intracranial pressure (ICP) is monitored. However, current measurement techniques are invasive and thus not practical in the combat environment. The Pulsed Phase Lock Loop device, which was developed and patented by consultants Drs. Yost and Cantrell, uses a unique, noninvasive ultrasonic phase comparison method to measure slight changes in cranial volume which occur with changes in ICP. Year two studies included whole body head-up and head-down tilting effects on intracranial compliance and pressure in six healthy volunteers.

  13. Tubular system volume changes in twitch fibres from toad and rat skeletal muscle assessed by confocal microscopy.

    Science.gov (United States)

    Launikonis, Bradley S; Stephenson, D George

    2002-01-15

    The volume of the extracellular compartment (tubular system) within intact muscle fibres from cane toad and rat was measured under various conditions using confocal microscopy. Under physiological conditions at rest, the fractional volume of the tubular system (t-sys(Vol)) was 1.38 +/- 0.09 % (n = 17), 1.41 +/- 0.09 % (n = 12) and 0.83 +/- 0.07 % (n = 12) of the total fibre volume in the twitch fibres from toad iliofibularis muscle, rat extensor digitorum longus muscle and rat soleus muscle, respectively. In toad muscle fibres, the t-sys(Vol) decreased by 30 % when the tubular system was fully depolarized and decreased by 15 % when membrane cholesterol was depleted from the tubular system with methyl-beta-cyclodextrin but did not change as the sarcomere length was changed from 1.93 to 3.30 microm. There was also an increase by 30 % and a decrease by 25 % in t-sys(Vol) when toad fibres were equilibrated in solutions that were 2.5-fold hypertonic and 50 % hypotonic, respectively. When the changes in total fibre volume were taken into consideration, the t-sys(Vol) expressed as a percentage of the isotonic fibre volume did actually decrease as tonicity increased, revealing that the tubular system in intact fibres cannot be compressed below 0.9 % of the isotonic fibre volume. The results can be explained in terms of forces acting at the level of the tubular wall. These observations have important physiological implications showing that the tubular system is a dynamic membrane structure capable of changing its volume in response to the membrane potential, cholesterol depletion and osmotic stress but not when the sarcomere length is changed in resting muscle.

  14. Perfusion systems that minimize vascular volume fraction in engineered tissues.

    Science.gov (United States)

    Truslow, James G; Tien, Joe

    2011-06-01

    This study determines the optimal vascular designs for perfusing engineered tissues. Here, "optimal" describes a geometry that minimizes vascular volume fraction (the fractional volume of a tissue that is occupied by vessels) while maintaining oxygen concentration above a set threshold throughout the tissue. Computational modeling showed that optimal geometries depended on parameters that affected vascular fluid transport and oxygen consumption. Approximate analytical expressions predicted optima that agreed well with the results of modeling. Our results suggest one basis for comparing the effectiveness of designs for microvascular tissue engineering.

  15. Technical Note: Influence of Compton currents on profile measurements in small-volume ion chambers

    Energy Technology Data Exchange (ETDEWEB)

    Tanny, Sean; Sperling, Nicholas; Parsai, E. Ishmael, E-mail: e.parsai@utoledo.edu [Department of Radiation Oncology, University of Toledo Medical Center, 1325 Conference Drive, Toledo, Ohio 43614 (United States); Holmes, Shannon [Standard Imaging, 3120 Deming Way, Middleton, Wisconsin 53562 (United States)

    2015-10-15

    Purpose: This work is to evaluate the effects of Compton current generation in three small-volume ionization chambers on measured beam characteristics for electron fields. Methods: Beam scans were performed using Exradin A16, A26, and PTW 31014 microchambers. Scans with varying chamber components shielded were performed. Static point measurements, output factors, and cable only irradiations were performed to determine the contribution of Compton currents to various components of the chamber. Monte Carlo simulations were performed to evaluate why one microchamber showed a significant reduction in Compton current generation. Results: Beam profiles demonstrated significant distortion for two of the three chambers when scanned parallel to the chamber axis, produced by electron deposition within the wire. Measurements of ionization produced within the cable identified Compton current generation as the cause of these distortions. The size of the central collecting wire was found to have the greatest influence on the magnitude of Compton current generation. Conclusions: Microchambers can demonstrate significant (>5%) deviations from properties as measured with larger volume chambers (0.125 cm{sup 3} and above). These deviations can be substantially reduced by averaging measurements conducted at opposite polarities.

  16. Assessment of target volume doses in radiotherapy based on the standard and measured calibration curves

    Directory of Open Access Journals (Sweden)

    Gholamreza Fallah Mohammadi

    2015-01-01

    Full Text Available Context: In radiation treatments, estimation of the dose distribution in the target volume is one of the main components of the treatment planning procedure. To estimate the dose distribution, the information of electron densities is necessary. The standard curves determined by computed tomography (CT scanner that may be different from that of other oncology centers. In this study, the changes of dose calculation due to the different calibration curves (HU-ρel were investigated. Materials and Methods: Dose values were calculated based on the standard calibration curve that was predefined for the treatment planning system (TPS. The calibration curve was also extracted from the CT images of the phantom, and dose values were calculated based on this curve. The percentage errors of the calculated values were determined. Statistical Analysis Used: The statistical analyses of the mean differences were performed using the Wilcoxon rank-sum test for both of the calibration curves. Results and Discussion: The results show no significant difference for both of the measured and standard calibration curves (HU-ρel in 6, 15, and 18 MeV energies. In Wilcoxon ranked sum nonparametric test for independent samples with P < 0.05, the equality of monitor units for both of the curves to transfer 200 cGy doses to reference points was resulted. The percentage errors of the calculated values were lower than 2% and 1.5% in 6 and 15 MeV, respectively. Conclusion: From the results, it could be concluded that the standard calibration curve could be used in TPS dose calculation accurately.

  17. MARA (Multimode Airborne Radar Altimeter) system documentation. Volume 1: MARA system requirements document

    Science.gov (United States)

    Parsons, C. L. (Editor)

    1989-01-01

    The Multimode Airborne Radar Altimeter (MARA), a flexible airborne radar remote sensing facility developed by NASA's Goddard Space Flight Center, is discussed. This volume describes the scientific justification for the development of the instrument and the translation of these scientific requirements into instrument design goals. Values for key instrument parameters are derived to accommodate these goals, and simulations and analytical models are used to estimate the developed system's performance.

  18. Software Reliability, Measurement, and Testing. Volume 2. Guidebook for Software Reliability Measurement and Testing

    Science.gov (United States)

    1992-04-01

    test experiments. Of the three static techniques, 200-4 SOFTWARE TEST TECHNIQUES ST Code Review A Error/ Anamoly Detection T I Structure...anomaly is an unforeseen event , which may not be detected by error-protection mechanisms in time to prevent system failure. The existence of extensive... event , the more difficult it is to make a meaningful prediction. As an example, it can be seen that the reliability of an electronic equipment is known

  19. Validation of Respiratory Inductance Plethysmography for Measuring Tidal Volume in Swine.

    Science.gov (United States)

    Su, Zhenbo; Oto, Jun; Wang, Jingwen; Kimball, William R; Chenelle, Christopher T; Kacmarek, Robert M; King, David R; Jiang, Yandong; Duggan, Michael J

    2015-06-01

    Measuring tidal volume (VT) in nonintubated swine or swine with leaking breathing circuits is challenging. The aim of this study was to validate respiratory inductance plethysmography (RIP) for measuring VT in swine that are comparable in size to adult humans. To determine calibration curves, VT and RIP readings were obtained from anesthetized swine (n = 8; weight, 46-50 kg) during positive-pressure (mechanical) ventilation and spontaneous breathing. For positive-pressure ventilation, 6 pigs were mechanically ventilated by using the pressure-control mode. The 2 pigs in the spontaneously breathing cohort each received a single intravenous bolus dose of propofol to abolish spontaneous breathing; VT was measured during gradual return of their respiratory drive. A flow-volume sensor was placed between the proximal end of the endotracheal tube and breathing circuit for the recording of inspiratory and expiratory VT. RIP readings were recorded by using 2 bands, which simultaneously measured ribcage and abdominal excursions. The data revealed that VT was linearly correlated with the movements of both ribcage and abdomen as measured by using plethysmography over a large range of tidal volume (44 to 1065 mL). In addition, the intercept of the linear equation was small or even negative during spontaneous breathing but increased significantly (maximum, 145 mL, 59.2 ± 35.1 mL) during positive pressure ventilation. Our results indicate that VT in swine can be calculated by using a simple univariate linear regression equation with RIP readings obtained during either mechanical ventilation or spontaneous breathing.

  20. Measurement of maxillary sinus volume and available alveolar bone height using computed tomography

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Jae Hak; Han, Won Jeong; Choi, Young Hi; Kim, Eun Kyung [Dankook University College of Medicine, Seoul (Korea, Republic of)

    2003-03-15

    To aid in determining the volume of graft bone required before a maxillary sinus lift procedure and compare the alveolar bone height measurements taken by panoramic radiographs to those by CT images. Data obtained by both panoramic radiographs and CT examination of 25 patients were used in this study. Maxillary sinus volumes from the antral floor to heights of 5 mm, 10 mm, 15 mm, and 20 mm , were calculated. Alveolar bone height was measured on the panoramic images at each maxillary tooth site and corrected by magnification rate (PBH). Available bone height (ABH) and full bone height (FBH) was measured on reconstructed CT images. PBH was compared with ABH and FBH at the maxillary incisors, canines, premolars, and molars. Volumes of the inferior portion of the sinuses were 0.55 {+-} 0.41 cm{sup 3} for 5 mm lifts, 2.11 {+-} 0.68 cm{sup 3} for 10 mm, 4.26 {+-} 1.32 cm{sup 3} for 15 mm, 6.95 {+-} 2.01 cm{sup 3} for 20 mm. For the alveolar bone measurement, measurements by panoramic images were longer than available bone heights determined by CT images at the incisor and canine areas, and shorter than full bone heights on CT images at incisor, premolar, and molar areas (p<0.001). In bone grafting of the maxillary sinus floor, 0,96 cm{sup 3} or more is required for a 5 mm - lift, 2.79 cm{sup 3} or more for a 10 mm - lift, 5.58 cm{sup 3} or more for a 15 mm - lift, and 8.96 cm{sup 3} or more for a 20 mm - lift. Maxillary implant length determined using panoramic radiograph alone could result in underestimation or overestimation, according to the site involved.

  1. Noninvasive blood flow measurement and quantification of shunt volume by cine magnetic resonance in congenital heart disease

    Energy Technology Data Exchange (ETDEWEB)

    Sieverding, L.; Apitz, J. (Tuebingen Univ. (Germany). Abt. fuer Paediatrische Kardiologie); Jung, W.I. (Tuebingen Univ. (Germany). Abt. fuer Paediatrische Kardiologie Tuebingen Univ. (Germany). Physikalisches Inst.); Klose, U. (Tuebingen Univ. (Germany). Medizinisches Strahleninstitut und Roentgenabteilung)

    1992-04-01

    Based on the phase difference method as described by Nayler et al. we developed a gradient-echo sequence, which refocuses flow related phase shifts even for infants with their higher peak velocity, higher acceleration and faster heart rates. A repetition time (TR) of 15 ms provides a high temporal resolution for dynamic studies. Modification of the flow-rephasing gradient-echo sequence in slice select direction leads to a defined phase shift and the resultant phase difference images allow blood flow measurements in the great arteries and the calculation of blood volume per heart cycle (flow volume) to assess left and right ventricular stroke volume. This can also be achieved by calculation of the ventricular volume from contiguous slices of the whole heart, but, this in excessive measuring times. Both methods were applied in 6 examinations of children with congenital heart diseases (1 pulmonary sling, 1 coarctation of the aorta, 1 ventricular septal defect, 3 atrial septal defects). The age of the patients ranged from 3 months to 13.4 years (mean age 4.9 years). The regression analyses of both methods show a high correlation for systemic flow (y=-0.98+1.08 x, r=0.99, SEE=2.59 ml) and for pulmonary flow (y=-1.40+0.96 x, r=0.99, SEE=4.70 ml). The comparison of flow calculated Qp:Qs ratio and chamber size calculated Qp:Qs ratio with data obtained by heart catheterization show also a regression line close to the line of identity (y=-0.01+1.04 x, r=0.98, SEE=0.15 and y=0.28+0.96 x, r=0.81, SEE=0.47, respectively). (orig.).

  2. Accounting for uncertainty in volumes of seabed change measured with repeat multibeam sonar surveys

    Science.gov (United States)

    Schimel, Alexandre C. G.; Ierodiaconou, Daniel; Hulands, Lachlan; Kennedy, David M.

    2015-12-01

    Seafloors of unconsolidated sediment are highly dynamic features; eroding or accumulating under the action of tides, waves and currents. Assessing which areas of the seafloor experienced change and measuring the corresponding volumes involved provide insights into these important active sedimentation processes. Computing the difference between Digital Elevation Models (DEMs) obtained from repeat Multibeam Echosounders (MBES) surveys has become a common technique to identify these areas, but the uncertainty in these datasets considerably affects the estimation of the volumes displaced. The two main techniques used to take into account uncertainty in volume estimations are the limitation of calculations to areas experiencing a change in depth beyond a chosen threshold, and the computation of volumetric confidence intervals. However, these techniques are still in their infancy and, as a result, are often crude, seldom used or poorly understood. In this article, we explored a number of possible methodological advances to address this issue, including: (1) using the uncertainty information provided by the MBES data processing algorithm CUBE, (2) adapting fluvial geomorphology techniques for volume calculations using spatially variable thresholds and (3) volumetric histograms. The nearshore seabed off Warrnambool harbour - located in the highly energetic southwest Victorian coast, Australia - was used as a test site. Four consecutive MBES surveys were carried out over a four-months period. The difference between consecutive DEMs revealed an area near the beach experiencing large sediment transfers - mostly erosion - and an area of reef experiencing increasing deposition from the advance of a nearby sediment sheet. The volumes of sediment displaced in these two areas were calculated using the techniques described above, both traditionally and using the suggested improvements. We compared the results and discussed the applicability of the new methodological improvements

  3. Intraobserver and interobserver agreement of volume perfusion CT (VPCT) measurements in patients with lung lesions

    Energy Technology Data Exchange (ETDEWEB)

    Sauter, Alexander W., E-mail: alexander.sauter@klinikum.uni-tuebingen.de [Department of Diagnostic and Interventional Radiology, University Hospital of Tuebingen, Hoppe-Seyler-Str. 3, 72076 Tuebingen (Germany); Merkle, Anne, E-mail: anne_merkle@web.de [Department of Diagnostic and Interventional Radiology, University Hospital of Tuebingen, Hoppe-Seyler-Str. 3, 72076 Tuebingen (Germany); Schulze, Maximilian, E-mail: maximilian.schulze@med.uni-tuebingen.de [Department of Diagnostic and Interventional Radiology, University Hospital of Tuebingen, Hoppe-Seyler-Str. 3, 72076 Tuebingen (Germany); Spira, Daniel, E-mail: daniel.spira@med.uni-tuebingen.de [Department of Diagnostic and Interventional Radiology, University Hospital of Tuebingen, Hoppe-Seyler-Str. 3, 72076 Tuebingen (Germany); Hetzel, Juergen, E-mail: juergen.hetzel@med.uni-tuebingen.de [Departments of Oncology, Hematology, Immunology, Rheumatology and Pulmonology, University Hospital of Tuebingen, Otfried-Mueller-Str. 10, 72076 Tuebingen (Germany); Claussen, Claus D., E-mail: claus.claussen@med.uni-tuebingen.de [Department of Diagnostic and Interventional Radiology, University Hospital of Tuebingen, Hoppe-Seyler-Str. 3, 72076 Tuebingen (Germany); Horger, Marius S., E-mail: marius.horger@med.uni-tuebingen.de [Department of Diagnostic and Interventional Radiology, University Hospital of Tuebingen, Hoppe-Seyler-Str. 3, 72076 Tuebingen (Germany)

    2012-10-15

    Objectives: To evaluate intraobserver and interobserver agreement of manually encompassed lung lesions for perfusion measurements using volume-perfusion computed tomography (VPCT). Materials and methods: Institutional review board approval and informed consent were obtained. HIPAA guidelines were followed. A 65-s dynamic study was acquired with scan parameters 80 kV, 60 mA s (80 mA s for patients ≥70 kg), 128 × 0.6 mm collimation. Blood flow (BF), blood volume (BV) and K{sup trans} parameters were determined by syngo volume perfusion CT body with 88 lesions analyzed retrospectively. Results: Within-subject coefficients of variation for intraobserver agreement (range 6.59–12.82%) were superior to those for interobserver agreement (range 21.75–38.30%). Size-dependent analysis revealed lower agreements for lesions <4 cm as compared to larger lesions. Additionally, agreements of the upper, middle and lower lung zones were different. Conclusions: Intraobserver agreement was substantial for VPCT lung cancer perfusion measurements encouraging the use for tumor characterization and therapy response monitoring. Interobserver agreement is limited and unexperienced readers should be trained before using this new method.

  4. Determination of volume fractions in two-phase flows from sound speed measurement

    Energy Technology Data Exchange (ETDEWEB)

    Chaudhuri, Anirban [Los Alamos National Laboratory; Sinha, Dipen N. [Los Alamos National Laboratory; Osterhoudt, Curtis F. [University of Alaska

    2012-08-15

    Accurate measurement of the composition of oil-water emulsions within the process environment is a challenging problem in the oil industry. Ultrasonic techniques are promising because they are non-invasive and can penetrate optically opaque mixtures. This paper presents a method of determining the volume fractions of two immiscible fluids in a homogenized two-phase flow by measuring the speed of sound through the composite fluid along with the instantaneous temperature. Two separate algorithms are developed by representing the composite density as (i) a linear combination of the two densities, and (ii) a non-linear fractional formulation. Both methods lead to a quadratic equation with temperature dependent coefficients, the root of which yields the volume fraction. The densities and sound speeds are calibrated at various temperatures for each fluid component, and the fitted polynomial is used in the final algorithm. We present results when the new algorithm is applied to mixtures of crude oil and process water from two different oil fields, and a comparison of our results with a Coriolis meter; the difference between mean values is less than 1%. Analytical and numerical studies of sensitivity of the calculated volume fraction to temperature changes and calibration errors are also presented.

  5. Accurately measuring volume of soil samples using low cost Kinect 3D scanner

    Science.gov (United States)

    van der Sterre, Boy-Santhos; Hut, Rolf; van de Giesen, Nick

    2013-04-01

    The 3D scanner of the Kinect game controller can be used to increase the accuracy and efficiency of determining in situ soil moisture content. Soil moisture is one of the principal hydrological variables in both the water and energy interactions between soil and atmosphere. Current in situ measurements of soil moisture either rely on indirect measurements (of electromagnetic constants or heat capacity) or on physically taking a sample and weighing it in a lab. The bottleneck in accurately retrieving soil moisture using samples is the determining of the volume of the sample. Currently this is mostly done by the very time consuming "sand cone method" in which the volume were the sample used to sit is filled with sand. We show that 3D scanner that is part of the 150 game controller extension "Kinect" can be used to make 3D scans before and after taking the sample. The accuracy of this method is tested by scanning forms of known volume. This method is less time consuming and less error-prone than using a sand cone.

  6. Volumic activities measurements and equivalent doses calculation of indoor 222Rn in Morocco

    Directory of Open Access Journals (Sweden)

    Abdelmajid Choukri

    2015-09-01

    Full Text Available Purpose: As a way of prevention, we have measured the volumic activities of indoor 222Rn and we have calculated the corresponding effective dose in some dwellings and enclosed areas in Morocco. Seasonal variation of Radon activities and Relationships between variation of these activities and some parameters such height, depth and type of construction were also established in this work.Methods: The passive time-integrated method of using a solid state nuclear track detector (LR-115 type II was employed. These films, cut in pieces of 3.4 ´ 2.5 cm2, were placed in detector holders and enclosed in heat-scaled polyethylene bags.Results: The measured volumic activities of radon vary in houses, between 31 and 136 Bq/m3 (0.55 and 2.39 mSv/year with an average value of 80 Bq/m3 (1.41 mSv/year. In enclosed work area, they vary between 60 Bq/m3 (0.38 mSv/year in an ordinary area to 1884 Bq/m3 (11.9 mSv/year at not airy underground level of 12 m. the relatively higher volumic activities of 222Rn in houses were measured in Youssoufia and khouribga towns situated in regions rich in phosphate deposits. Measurements at the geophysical observatory of Berchid show that the volumic activity of radon increases with depth, this is most probably due to decreased ventilation. Conclusion: The obtained results show that the effective dose calculated for indoor dwellings are comparable to those obtained in other regions in the word. The risks related to the volumic activities of indoor radon could be avoided by simple precautions such the continuous ventilation. The reached high value of above 1884 Bq/m3 don't present any risk for workers health in the geophysical observatory of Berchid because workers spend only a few minutes by day in the cellar to control and reregister data.

  7. High Temperature Superconducting Maglev Measurement System

    OpenAIRE

    Wang, Jia-Su; Wang, Su-Yu

    2010-01-01

    Three high temperature superconducting (HTS) Maglev measurement systems were successfully developed in the Applied Superconductivity Laboratory (ASCLab) of Southwest Jiaotong University, P. R. China. These systems include liquid nitrogen vessel, Permanent Magnet Guideway (PMG), data collection and processing, mechanical drive and Autocontrol features. This chapter described the three different measuring systems along with their theory of operations and workflow. The SCML-01 HTS Maglev measure...

  8. Does bioimpedance analysis or measurement of natriuretic peptides aid volume assessment in peritoneal dialysis patients?

    Science.gov (United States)

    Davenport, Andrew

    2013-01-01

    Cardiovascular mortality remains the commonest cause of death for peritoneal dialysis patients. As such, preventing persistent hypervolemia is important. On the other hand, hypovolemia may potentially risk episodes of acute kidney injury and loss of residual renal function, a major determinant of peritoneal dialysis technique survival. Bioimpedance has developed from a single-frequency research tool to a multi-frequency bioelectrical impedance analysis readily available in the clinic and capable of measuring extracellular, intracellular, and total body water. Similarly, natriuretic peptides released from the heart because of myocardial stretch and increased intracardiac volume have also been variously reported to be helpful in assessing volume status in peritoneal dialysis patients. The question then arises whether these newer technologies and biomarkers have supplanted the time-honored clinical assessment of hydration status or whether they are merely adjuncts that aid the experienced clinician.

  9. Shape and deformation measurements of 3D objects using volume speckle field and phase retrieval

    DEFF Research Database (Denmark)

    Anand, A; Chhaniwal, VK; Almoro, Percival;

    2009-01-01

    Shape and deformation measurement of diffusely reflecting 3D objects are very important in many application areas, including quality control, nondestructive testing, and design. When rough objects are exposed to coherent beams, the scattered light produces speckle fields. A method to measure...... the shape and deformation of 3D objects from the sequential intensity measurements of volume speckle field and phase retrieval based on angular-spectrum propagation technique is described here. The shape of a convex spherical surface was measured directly from the calculated phase map, and micrometer......-sized deformation induced on a metal sheet was obtained upon subtraction of the phase, corresponding to unloaded and loaded states. Results from computer simulations confirm the experiments. (C) 2009 Optical Society of America....

  10. System Development of Estimated Figures of Volume Production Plan

    Science.gov (United States)

    Brazhnikov, Maksim A.; Khorina, Irina V.; Minina, Yulia I.; Kolyasnikova, Lyudmila V.; Streltsov, Aleksey V.

    2016-01-01

    The relevance of this problem is primarily determined by a necessity of improving production efficiency in conditions of innovative development of the economy and implementation of Import Substitution Program. The purpose of the article is development of set of criteria and procedures for the comparative assessment of alternative volume production…

  11. 9th Annual Systems Engineering Conference: Volume 4 Thursday

    Science.gov (United States)

    2006-10-26

    Connectivity, Speed, Volume • Enterprise application integration • Workflow integration or multi-media • Federated search capability • Link analysis and...categorization, federated search & automated discovery of information — Collaborative tools to quickly share relevant information Built on commercial

  12. 600-GHz Electronically Tunable Vector Measurement System

    Science.gov (United States)

    Dengler, Robert; Maiwald, Frank; Siegel, Peter

    2007-01-01

    A compact, high-dynamic-range, electronically tunable vector measurement system that operates in the frequency range from approximately 560 to approximately 635 GHz has been developed as a prototype of vector measurement systems that would be suitable for use in nearly-real-time active submillimeter-wave imaging. As used here, 'vector measurement system" signifies an instrumentation system that applies a radio-frequency (RF) excitation to an object of interest and measures the resulting amplitude and phase response, relative to either the applied excitatory signal or another reference signal related in a known way to applied excitatory signal.

  13. Study on portable optical 3D coordinate measuring system

    Science.gov (United States)

    Ren, Tongqun; Zhu, Jigui; Guo, Yinbiao

    2009-05-01

    A portable optical 3D coordinate measuring system based on digital Close Range Photogrammetry (CRP) technology and binocular stereo vision theory is researched. Three ultra-red LED with high stability is set on a hand-hold target to provide measuring feature and establish target coordinate system. Ray intersection based field directional calibrating is done for the intersectant binocular measurement system composed of two cameras by a reference ruler. The hand-hold target controlled by Bluetooth wireless communication is free moved to implement contact measurement. The position of ceramic contact ball is pre-calibrated accurately. The coordinates of target feature points are obtained by binocular stereo vision model from the stereo images pair taken by cameras. Combining radius compensation for contact ball and residual error correction, object point can be resolved by transfer of axes using target coordinate system as intermediary. This system is suitable for on-field large-scale measurement because of its excellent portability, high precision, wide measuring volume, great adaptability and satisfying automatization. It is tested that the measuring precision is near to +/-0.1mm/m.

  14. Measurements and modeling of the volume scattering function in the coastal northern Adriatic Sea

    Science.gov (United States)

    Berthon, Jean-François; Shybanov, Eugeny; Lee, Michael E.-G.; Zibordi, Giuseppe

    2007-08-01

    We performed measurements of the volume scattering function (VSF) between 0.5° and 179° with an angular resolution of 0.3° in the northern Adriatic Sea onboard an oceanographic platform during three different seasons, using the multispectral volume scattering meter (MVSM) instrument. We observed important differences with respect to Petzold's commonly used functions, whereas the Fournier-Forand's analytical formulation provided a rather good description of the measured VSF. The comparison of the derived scattering, bp(λ) and backscattering, bbp(λ) coefficients for particles with the measurements performed with the classical AC-9 and Hydroscat-6 showed agreement to within 20%. The use of an empirical relationship for the derivation of bb(λ) from β(ψ,λ) at ψ=140° was validated for this coastal site although ψ=118° was confirmed to be the most appropriate angle. The low value of the factor used to convert β(ψ,λ) into bb(λ) within the Hydroscat-6 processing partially contributed to the underestimation of bb(λ) with respect to the MVSM. Finally, use of the Kopelevich model together with a measurement of bp(λ) at λ=555 nm allowed us to reconstruct the VSF with average rms percent differences between 8 and 15%.

  15. Measuring tree height and preparation volume table using an innovative method.

    Science.gov (United States)

    Lotfalian, Majid; Nouri, Zahra; Kooch, Yahya; Zobeiri, Mahmoud

    2007-10-15

    Zarbin (Cupressus sempervirence var. horizontalis) with its unique characteristics is one of the worthiest species which can be found in the central area of Alborz in the North of Iran. Especially in the Roodbar-manjil area, Chaloos-Hassanabad valley as well as it extends from Zarringol area to Gorgan. Although the distribution areas of this species have been protected, these forests have been invaded by the villagers who use this useful wood. For this reason in the Roodbar area, trees with DBH>30 cm are extremely rare. To recognize and to be aware of the stand quantity, the current research tries to calculate the species volume table in Roodbar area, to be the basis for any calculation of the volume of stand in the region. For this purpose, trees have been sampled using the line sampling method. After estimating the form factor, Tarif table have been prepared. In this study, a new method for measuring tree height is presented, in which, instead of measuring slope distance from observer to tree (which is difficult in young conifers because of existence branches in lower height) distance between the eye level of observer to tree butt is measured. Which doing of it is easier, time of field work is decreased and accuracy of measurement and calculation is increased.

  16. THE INFLUENCE OF DROPLET VOLUME AND CONTACT-ANGLE ON LIQUID SURFACE-TENSION MEASUREMENTS BY AXISYMMETRICAL DROP SHAPE ANALYSIS-PROFILE (ADSA-P)

    NARCIS (Netherlands)

    BUSSCHER, HJ

    1991-01-01

    The axisymmetric drop shape analysis-profile (ADSA-P) technique was evaluated with respect to the influence of contact angle and droplet volume. The system was implemented on our standard contact angle measuring apparatus employing a Vidicon video camera and a 512 x 256 pixels framegrabber. For cali

  17. Coastwide Reference Monitoring System (CRMS) Vegetation Volume Index: An assessment tool for marsh habitat focused on the three-dimensional structure at CRMS vegetation monitoring stations

    Science.gov (United States)

    Wood, William B.; Visser, Jenneke M.; Piazza, Sarai C.; Sharp, Leigh A.; Hundy, Laura C.; McGinnis, Tommy E.

    2015-12-04

    A Vegetation Volume (VV) variable and Vegetation Volume Index (VVI) have been developed for the Coastwide Reference Monitoring System (CRMS). The VV is a measure of the amount of three-dimensional vegetative structure present at each CRMS site and is based on vegetation data collected annually. The VV uses 10 stations per CRMS site to quantify four vegetation layers: carpet, herbaceous, shrub, and tree. For each layer an overall live vegetation percent cover and height are collected to create a layer volume; the individual layer volumes are then summed to generate a site vegetation volume profile. The VV uses the two-dimensional area of live vegetative cover (in square meters) multiplied by the height (in meters) of each layer to produce a volume (in cubic meters) for each layer present in a 2-meter by 2-meter station. These layers are additive, yielding a total volume for each of the 10 herbaceous vegetation stations and an overall CRMS marsh site average.

  18. A magnetic suspension system for measuring liquid density

    Directory of Open Access Journals (Sweden)

    Luz María Centeno González

    2013-04-01

    Full Text Available Density is a derived quantity of mass and length; it is defined as mass per volume unit and its SI unit is kg/m3. National metrology institutes have been designing and building their own magnetic suspension systems during the last 5 decades for making fluid density measurements; this has allowed them to carry out research into liquids and gases’ physical characteristics. This paper was aimed at designing and developing a magnetic suspension system for a magnetic balance used in determining liquid density to be used in CENAM’s metrology density laboratories.

  19. Broadband Fan Noise Prediction System for Turbofan Engines. Volume 2; BFaNS User's Manual and Developer's Guide

    Science.gov (United States)

    Morin, Bruce L.

    2010-01-01

    Pratt & Whitney has developed a Broadband Fan Noise Prediction System (BFaNS) for turbofan engines. This system computes the noise generated by turbulence impinging on the leading edges of the fan and fan exit guide vane, and noise generated by boundary-layer turbulence passing over the fan trailing edge. BFaNS has been validated on three fan rigs that were tested during the NASA Advanced Subsonic Technology Program (AST). The predicted noise spectra agreed well with measured data. The predicted effects of fan speed, vane count, and vane sweep also agreed well with measurements. The noise prediction system consists of two computer programs: Setup_BFaNS and BFaNS. Setup_BFaNS converts user-specified geometry and flow-field information into a BFaNS input file. From this input file, BFaNS computes the inlet and aft broadband sound power spectra generated by the fan and FEGV. The output file from BFaNS contains the inlet, aft and total sound power spectra from each noise source. This report is the second volume of a three-volume set documenting the Broadband Fan Noise Prediction System: Volume 1: Setup_BFaNS User s Manual and Developer s Guide; Volume 2: BFaNS User s Manual and Developer s Guide; and Volume 3: Validation and Test Cases. The present volume begins with an overview of the Broadband Fan Noise Prediction System, followed by step-by-step instructions for installing and running BFaNS. It concludes with technical documentation of the BFaNS computer program.

  20. Broadband Fan Noise Prediction System for Turbofan Engines. Volume 1; Setup_BFaNS User's Manual and Developer's Guide

    Science.gov (United States)

    Morin, Bruce L.

    2010-01-01

    Pratt & Whitney has developed a Broadband Fan Noise Prediction System (BFaNS) for turbofan engines. This system computes the noise generated by turbulence impinging on the leading edges of the fan and fan exit guide vane, and noise generated by boundary-layer turbulence passing over the fan trailing edge. BFaNS has been validated on three fan rigs that were tested during the NASA Advanced Subsonic Technology Program (AST). The predicted noise spectra agreed well with measured data. The predicted effects of fan speed, vane count, and vane sweep also agreed well with measurements. The noise prediction system consists of two computer programs: Setup_BFaNS and BFaNS. Setup_BFaNS converts user-specified geometry and flow-field information into a BFaNS input file. From this input file, BFaNS computes the inlet and aft broadband sound power spectra generated by the fan and FEGV. The output file from BFaNS contains the inlet, aft and total sound power spectra from each noise source. This report is the first volume of a three-volume set documenting the Broadband Fan Noise Prediction System: Volume 1: Setup_BFaNS User s Manual and Developer s Guide; Volume 2: BFaNS User's Manual and Developer s Guide; and Volume 3: Validation and Test Cases. The present volume begins with an overview of the Broadband Fan Noise Prediction System, followed by step-by-step instructions for installing and running Setup_BFaNS. It concludes with technical documentation of the Setup_BFaNS computer program.

  1. WSN-Based Space Charge Density Measurement System.

    Science.gov (United States)

    Deng, Dawei; Yuan, Haiwen; Lv, Jianxun; Ju, Yong

    2017-01-01

    It is generally acknowledged that high voltage direct current (HVDC) transmission line endures the drawback of large area, because of which the utilization of cable for space charge density monitoring system is of inconvenience. Compared with the traditional communication network, wireless sensor network (WSN) shows advantages in small volume, high flexibility and strong self-organization, thereby presenting great potential in solving the problem. Additionally, WSN is more suitable for the construction of distributed space charge density monitoring system as it has longer distance and higher mobility. A distributed wireless system is designed for collecting and monitoring the space charge density under HVDC transmission lines, which has been widely applied in both Chinese state grid HVDC test base and power transmission projects. Experimental results of the measuring system demonstrated its adaptability in the complex electromagnetic environment under the transmission lines and the ability in realizing accurate, flexible, and stable demands for the measurement of space charge density.

  2. Control Volume Analysis, Entropy Balance and the Entropy Production in Flow Systems

    OpenAIRE

    Niven, Robert K.; Noack, Bernd R.

    2014-01-01

    This chapter concerns "control volume analysis", the standard engineering tool for the analysis of flow systems, and its application to entropy balance calculations. Firstly, the principles of control volume analysis are enunciated and applied to flows of conserved quantities (e.g. mass, momentum, energy) through a control volume, giving integral (Reynolds transport theorem) and differential forms of the conservation equations. Several definitions of steady state are discussed. The concept of...

  3. Configuration Analysis of the ERS Points in Large-Volume Metrology System.

    Science.gov (United States)

    Jin, Zhangjun; Yu, Cijun; Li, Jiangxiong; Ke, Yinglin

    2015-09-22

    In aircraft assembly, multiple laser trackers are used simultaneously to measure large-scale aircraft components. To combine the independent measurements, the transformation matrices between the laser trackers' coordinate systems and the assembly coordinate system are calculated, by measuring the enhanced referring system (ERS) points. This article aims to understand the influence of the configuration of the ERS points that affect the transformation matrix errors, and then optimize the deployment of the ERS points to reduce the transformation matrix errors. To optimize the deployment of the ERS points, an explicit model is derived to estimate the transformation matrix errors. The estimation model is verified by the experiment implemented in the factory floor. Based on the proposed model, a group of sensitivity coefficients are derived to evaluate the quality of the configuration of the ERS points, and then several typical configurations of the ERS points are analyzed in detail with the sensitivity coefficients. Finally general guidance is established to instruct the deployment of the ERS points in the aspects of the layout, the volume size and the number of the ERS points, as well as the position and orientation of the assembly coordinate system.

  4. Imaging Systems for Size Measurements of Debrisat Fragments

    Science.gov (United States)

    Shiotani, B.; Scruggs, T.; Toledo, R.; Fitz-Coy, N.; Liou, J. C.; Sorge, M.; Huynh, T.; Opiela, J.; Krisko, P.; Cowardin, H.

    2017-01-01

    The overall objective of the DebriSat project is to provide data to update existing standard spacecraft breakup models. One of the key sets of parameters used in these models is the physical dimensions of the fragments (i.e., length, average-cross sectional area, and volume). For the DebriSat project, only fragments with at least one dimension greater than 2 mm are collected and processed. Additionally, a significant portion of the fragments recovered from the impact test are needle-like and/or flat plate-like fragments where their heights are almost negligible in comparison to their other dimensions. As a result, two fragment size categories were defined: 2D objects and 3D objects. While measurement systems are commercially available, factors such as measurement rates, system adaptability, size characterization limitations and equipment costs presented significant challenges to the project and a decision was made to develop our own size characterization systems. The size characterization systems consist of two automated image systems, one referred to as the 3D imaging system and the other as the 2D imaging system. Which imaging system to use depends on the classification of the fragment being measured. Both imaging systems utilize point-and-shoot cameras for object image acquisition and create representative point clouds of the fragments. The 3D imaging system utilizes a space-carving algorithm to generate a 3D point cloud, while the 2D imaging system utilizes an edge detection algorithm to generate a 2D point cloud. From the point clouds, the three largest orthogonal dimensions are determined using a convex hull algorithm. For 3D objects, in addition to the three largest orthogonal dimensions, the volume is computed via an alpha-shape algorithm applied to the point clouds. The average cross-sectional area is also computed for 3D objects. Both imaging systems have automated size measurements (image acquisition and image processing) driven by the need to quickly

  5. [INFLUENCE OF LIPOSUCTION OF LARGE VOLUME ON SYSTEMIC AND LUNG CIRCULATION, OXIGENATED LUNG FUNCTION].

    Science.gov (United States)

    Nikolaeva, I P; Kapranova, A S; Popova, V B; Lodyagin, A N; Frolova, T A

    2015-01-01

    The authors measured the changes of hemodynamics in 72 patients. It was also estimated a blood oxygenation and volume of liquid sectors of the organism in different degree of obesity before and after liposuction of the large volume. It was shown, that this operation facilitated to an improvement of respiratory lung function due to changes of pulmonary circulation.

  6. SQUID-based measuring systems

    Indian Academy of Sciences (India)

    M P Janawadkar; R Baskaran; R Nagendran; K Gireesan; N Harishkumar; Rita Saha; L S Vaidhyanathan; J Jayapandian; Y Hariharan; T S Radhakrishnan

    2002-05-01

    A program has been developed and initiated at the Indira Gandhi Centre for Atomic Research (IGCAR) for the utilization of SQUID sensors in various application areas. DC SQUID sensors based on Nb–AlO–Nb Josephson junctions have been designed and developed inhouse along with associated flux-locked loop (FLL) electronics. A compact low field SQUID magnetometer insertible in a liquid helium storage dewar has also been developed inhouse and is in use. Efforts to build a high field SQUID magnetometer, SQUID-DAC system, are in progress. A planar gradiometric DC SQUID sensor for non-destructive evaluation (NDE) application to be used in relatively unshielded environment has been designed and developed. An easily portable NDE cryostat with a small lift-off distance, to be used in external locations has been designed and tested. The magnetic field produced by a given two-dimensional current density distribution is inverted using the Fourier transform technique.

  7. 100-N technical manual. Volume 2A: Systems descriptions

    Energy Technology Data Exchange (ETDEWEB)

    1963-12-31

    This report contains engineering drawings for the control room, reactor monitoring systems, and reactor control systems for the N reactor. Each console in the control room is detailed. Other systems discussed are: stack air monitoring system, charging machine control systems, and heating and ventilation control systems. A N reactor plant glossary is included.

  8. Measurement of SIFT operating system overhead

    Science.gov (United States)

    Palumbo, D. L.; Butler, R. W.

    1985-01-01

    The overhead of the software implemented fault tolerance (SIFT) operating system was measured. Several versions of the operating system evolved. Each version represents different strategies employed to improve the measured performance. Three of these versions are analyzed. The internal data structures of the operating systems are discussed. The overhead of the SIFT operating system was found to be of two types: vote overhead and executive task overhead. Both types of overhead were found to be significant in all versions of the system. Improvements substantially reduced this overhead; even with these improvements, the operating system consumed well over 50% of the available processing time.

  9. Electro-optical imaging system performance measurement

    NARCIS (Netherlands)

    Bijl, P.; Toet, A.; Valeton, J.M.

    2003-01-01

    The minimum resolvable temperature difference (MRTD), the minimum resolvable contrast (MRC), and the triangle orientation discrimination (TOD) are end-to-end EO system performance measures; that is, laboratory measures that characterize EO system performance with a human observer in the loop. Such s

  10. Measurement of anterior chamber volume with rotating scheimpflug camera and anterior segment optical coherence tomography

    Institute of Scientific and Technical Information of China (English)

    FU Jing; LI Shu-ning; WANG Xiao-zhen; WU Ge-wei; MU Da-peng; WANG Jian; WANG Ning-li

    2010-01-01

    Background Measurement of anterior segment parameters plays an important role in diagnosis and treatment of glaucoma. The objective of this study was to evaluate the repeatability and reproducibility of anterior chamber volume (ACV) measurements with rotating scheimpflug camera (RSC) and to examine agreement with anterior segment optical coherence tomography (AS-OCT). Methods Thirty nine healthy normal subjects were recruited from the Eye Center of Tongren Hospital. ACV was measured using RSC and AS-OCT in a randomly selected eye for each subject. For RSC measurements, both automatic and manual ACV measurements and 2 independent operators' ACV measurements were obtained. All subjects were invited for 3 visits within a week to evaluate repeatability and reproducibility of ACV measurement by RSC. Agreement was evaluated between RSC and AS-OCT. Results Good repeatability and reproducibility were found for both automatic and manual ACV measurements obtained by RSC. For intrasession repeatability, coefficient of variation (CVw) and intraclass correlation coefficient (ICC) values for automatic were 3.52% and 0.98; the values for manual were 3.44% and 0.97, respectively. For intersession reproducibility, the respective CVw and ICC values were 3.96% and 0.96. Good agreement was also found in 2 operators for both automatic and manual ACV measurements; nevertheless, poor agreement was found between RSC and AS-OCT (95% confidence interval (CI) for agreement of automatic RSC measurement versus AS-OCT were -96.3 to 72.8 μl and 95% CI for agreement of manual RSC measurement versus AS-OCT were between -41.7 to 10.1 μl). Conclusions Both RSC automatic and manual ACV measurements showed good repeatability and reproducibility, and showed comparable agreement between 2 independent operators, but poor agreement was found between RSC and AS-OCT.

  11. Measurement of anterior chamber volume with rotating scheimpflug camera and anterior segment optical coherence tomography.

    Science.gov (United States)

    Fu, Jing; Li, Shu-ning; Wang, Xiao-zhen; Wu, Ge-wei; Mu, Da-peng; Wang, Jian; Wang, Ning-li

    2010-01-20

    Measurement of anterior segment parameters plays an important role in diagnosis and treatment of glaucoma. The objective of this study was to evaluate the repeatability and reproducibility of anterior chamber volume (ACV) measurements with rotating scheimpflug camera (RSC) and to examine agreement with anterior segment optical coherence tomography (AS-OCT). Thirty nine healthy normal subjects were recruited from the Eye Center of Tongren Hospital. ACV was measured using RSC and AS-OCT in a randomly selected eye for each subject. For RSC measurements, both automatic and manual ACV measurements and 2 independent operators' ACV measurements were obtained. All subjects were invited for 3 visits within a week to evaluate repeatability and reproducibility of ACV measurement by RSC. Agreement was evaluated between RSC and AS-OCT. Good repeatability and reproducibility were found for both automatic and manual ACV measurements obtained by RSC. For intrasession repeatability, coefficient of variation (CVw) and intraclass correlation coefficient (ICC) values for automatic were 3.52% and 0.98; the values for manual were 3.44% and 0.97, respectively. For intersession reproducibility, the respective CVw and ICC values were 3.96% and 0.96. Good agreement was also found in 2 operators for both automatic and manual ACV measurements; nevertheless, poor agreement was found between RSC and AS-OCT (95% confidence interval (CI) for agreement of automatic RSC measurement versus AS-OCT were -96.3 to 72.8 microl and 95% CI for agreement of manual RSC measurement versus AS-OCT were between -41.7 to 10.1 microl). Both RSC automatic and manual ACV measurements showed good repeatability and reproducibility, and showed comparable agreement between 2 independent operators, but poor agreement was found between RSC and AS-OCT.

  12. A Polypyrrole-based Strain Sensor Dedicated to Measure Bladder Volume in Patients with Urinary Dysfunction

    Directory of Open Access Journals (Sweden)

    Vamsy P. Chodavarapu

    2008-08-01

    Full Text Available This paper describes a new technique to measure urine volume in patients with urinary bladder dysfunction. Polypyrrole – an electronically conducting polymer - is chemically deposited on a highly elastic fabric. This fabric, when placed around a phantom bladder, produced a reproducible change in electrical resistance on stretching. The resistance response to stretching is linear in 20%-40% strain variation. This change in resistance is influenced by chemical fabrication conditions. We also demonstrate the dynamic mechanical testing of the patterned polypyrrole on fabric in order to show the feasibility of passive interrogation of the strain sensor for biomedical sensing applications.

  13. Self-heating probe instrument and method for measuring high temperature melting volume change rate of material

    Science.gov (United States)

    Wang, Junwei; Wang, Zhiping; Lu, Yang; Cheng, Bo

    2013-03-01

    The castings defects are affected by the melting volume change rate of material. The change rate has an important effect on running safety of the high temperature thermal storage chamber, too. But the characteristics of existing measuring installations are complex structure, troublesome operation and low precision. In order to measure the melting volume change rate of material accurately and conveniently, a self-designed measuring instrument, self-heating probe instrument, and measuring method are described. Temperature in heating cavity is controlled by PID temperature controller; melting volume change rate υ and molten density are calculated based on the melt volume which is measured by the instrument. Positive and negative υ represent expansion and shrinkage of the sample volume after melting, respectively. Taking eutectic LiF+CaF2 for example, its melting volume change rate and melting density at 1 123 K are -20.6% and 2 651 kg·m-3 measured by this instrument, which is only 0.71% smaller than literature value. Density and melting volume change rate of industry pure aluminum at 973 K and analysis pure NaCl at 1 123 K are detected by the instrument too. The measure results are agreed with report values. Measuring error sources are analyzed and several improving measures are proposed. In theory, the measuring errors of the change rate and molten density which are measured by the self-designed instrument is nearly 1/20-1/50 of that measured by the refitted mandril thermal expansion instrument. The self-designed instrument and method have the advantages of simple structure, being easy to operate, extensive applicability for material, relatively high accuracy, and most importantly, temperature and sample vapor pressure have little effect on the measurement accuracy. The presented instrument and method solve the problems of complicated structure and procedures, and large measuring errors for the samples with high vapor pressure by existing installations.

  14. A white matter lesion-filling approach to improve brain tissue volume measurements

    Directory of Open Access Journals (Sweden)

    Sergi Valverde

    2014-01-01

    Full Text Available Multiple sclerosis white matter (WM lesions can affect brain tissue volume measurements of voxel-wise segmentation methods if these lesions are included in the segmentation process. Several authors have presented different techniques to improve brain tissue volume estimations by filling WM lesions before segmentation with intensities similar to those of WM. Here, we propose a new method to refill WM lesions, where contrary to similar approaches, lesion voxel intensities are replaced by random values of a normal distribution generated from the mean WM signal intensity of each two-dimensional slice. We test the performance of our method by estimating the deviation in tissue volume between a set of 30 T1-w 1.5 T and 30 T1-w 3 T images of healthy subjects and the same images where: WM lesions have been previously registered and afterwards replaced their voxel intensities to those between gray matter (GM and WM tissue. Tissue volume is computed independently using FAST and SPM8. When compared with the state-of-the-art methods, on 1.5 T data our method yields the lowest deviation in WM between original and filled images, independently of the segmentation method used. It also performs the lowest differences in GM when FAST is used and equals to the best method when SPM8 is employed. On 3 T data, our method also outperforms the state-of-the-art methods when FAST is used while performs similar to the best method when SPM8 is used. The proposed technique is currently available to researchers as a stand-alone program and as an SPM extension.

  15. [Wireless ECG measurement system with capacitive coupling].

    Science.gov (United States)

    Aleksandrowicz, Adrian; Walter, Marian; Leonhardt, Steffen

    2007-04-01

    This paper describes a measurement system that captures an electrocardiogram (ECG) using capacitively coupled electrodes. The measurement system was integrated into an off-the-shelf office chair (so-called "Aachen SmartChair"). Whereas for classical ECG measurement adhesive is used to attach conductively coupled electrodes to bare skin, the system presented allows ECG measurement through clothing without direct skin contact. Furthermore, a ZigBee communication module was integrated to allow wireless transmission of ECG data to a PC or an ICU patient monitor. For system validation, classical ECG using conductive electrodes was obtained simultaneously. First measurement results, including variations of cloth thickness and material, are presented and some of the system-specific problems of this approach are discussed.

  16. Microminiature Inertial Measurement System and Its Applications

    Institute of Scientific and Technical Information of China (English)

    毛刚; 顾启泰

    2001-01-01

    The microminiature inertial measurement system, a new style of inertial measurement system, hasmany advantages compared with traditional systems, such as small size, Iow mass, low cost, low powerconsumption, high bearing capacity, and long life. Undoubtedly, it will have wide applications in military andcommercial fields. However, current micro inertial sensors do not have sufficient accuracy, so, its applicationsare limited to some extent. This paper describes a microminiature inertial measurement system and its design,operating theory and error control techniques. In addition, its performance and applications are evaluated.``

  17. Volume Measurements of Laser-generated Pits for In Situ Geochronology using KArLE (Potassium-Argon Laser Experiment)

    Science.gov (United States)

    French, R. A.; Cohen, B. A.; Miller, J. S.

    2014-01-01

    The Potassium-Argon Laser Experiment( KArLE), is composed of two main instruments: a spectrometer as part of the Laser-Induced Breakdown Spectroscopy (LIBS) method and a Mass Spectrometer (MS). The LIBS laser ablates a sample and creates a plasma cloud, generating a pit in the sample. The LIBS plasma is measured for K abundance in weight percent and the released gas is measured using the MS, which calculates Ar abundance in mols. To relate the K and Ar measurements, total mass of the ablated sample is needed but can be difficult to directly measure. Instead, density and volume are used to calculate mass, where density is calculated based on the elemental composition of the rock (from the emission spectrum) and volume is determined by pit morphology. This study aims to reduce the uncertainty for KArLE by analyzing pit volume relationships in several analog materials and comparing methods of pit volume measurements and their associated uncertainties.

  18. System 80+{trademark} Standard Design: CESSAR design certification. Volume 8: Amendment I

    Energy Technology Data Exchange (ETDEWEB)

    1990-12-21

    This report, entitled Combustion Engineering Standard Safety Analysis Report -- Design Certification (CESSAR-DC), has been prepared in support of the industry effort to standardize nuclear plant designs. These volumes describe the Combustion Engineering, Inc. System 80{sup +}{trademark} Standard Design. This volume 8 provides a description of instrumentation and controls.

  19. A Novel Method to Compute Breathing Volumes via Motion Capture Systems: Design and Experimental Trials.

    Science.gov (United States)

    Massaroni, Carlo; Cassetta, Eugenio; Silvestri, Sergio

    2017-03-24

    Respiratory assessment can be carried out by using motion capture systems. A geometrical model is mandatory in order to compute the breathing volume as a function of time from the markers trajectories. This study describes a novel model to compute volume changes and calculate respiratory parameters by using a motion capture system. The novel method, i.e. prism-based method, computes the volume enclosed within the chest by defining 82 prisms from the 89 markers attached to the subject chest. Volumes computed with this method are compared to spirometry volumes and to volumes computed by a conventional method based on the tetrahedrons decomposition of the chest wall and integrated in a commercial motion capture system. Eight healthy volunteers were enrolled and 30 seconds quiet breathing collected from each of them. Results show a better agreement between volumes computed by the prism-based method and the spirometry (discrepancy of 2.23%, R(2)=0.94) compared to the agreement between volumes computed by the conventional method and the spirometry (discrepancy of 3.56%, R(2)=0.92). The proposed method also showed better performances in the calculation of respiratory parameters. Our findings open up prospects for the further use of the new method in the breathing assessment via motion capture systems.

  20. System 80+{trademark} Standard Design: CESSAR design certification. Volume 17: Amendment I

    Energy Technology Data Exchange (ETDEWEB)

    1990-12-21

    This report, entitled Combustion Engineering Standard Safety Analysis Report -- Design Certification (CESSAR-DC), has been prepared in support of the industry effort to standardize nuclear plant designs. These volumes describes the Combustion Engineering, Inc. System 80+{trademark} Standard Design. This Volume 17 provides Appendix A of this report, closure of unresolved and Genetic Safety Issues.

  1. System 80+{trademark} Standard Design: CESSAR design certification. Volume 16: Amendment I

    Energy Technology Data Exchange (ETDEWEB)

    1990-12-21

    This report, entitled Combustion Engineering Standard Safety Analysis Report - Design Certification (CESSAR-DC), has been prepared in support of the industry effort to standardize nuclear plant designs. These volumes describe the Combustion Engineering, Inc. System 80+{trademark} Standard Design. This Volume 16 details the application of Human Factors Engineering in the design process.

  2. System 80+{trademark} Standard Design: CESSAR design certification. Volume 18: Amendment I

    Energy Technology Data Exchange (ETDEWEB)

    1990-12-21

    This report, entitled Combustion Engineering Standard Safety Analysis Report -- Design Certification (CESSAR-DC), has been prepared in support of the industry effort to standardize nuclear plant designs. These volumes describe the Combustion Engineering, Inc. System 80+{trademark} Standard Design. This Volume 18 provides Appendix B, Probabilistic Risk Assessment.

  3. Fourth international symposium on automotive propulsion systems. Volume I. [Eighteen papers

    Energy Technology Data Exchange (ETDEWEB)

    1977-01-01

    A pre-conference draft is given (in five volumes) of the proceedings of the 4th International Symposium on Automotive Propulsion Systems, held April 18-22, 1977, in Washington, D.C. Volume I contains eighteen papers; a separate abstract was prepared for each for ERDA Energy Research Abstracts (ERA).

  4. System 80+{trademark} Standard Design: CESSAR design certification. Volume 11: Amendment I

    Energy Technology Data Exchange (ETDEWEB)

    1990-12-21

    This report, entitled Combustion Engineering Standard Safety Analysis Report -- Design Certification (CESSAR-DC), has been prepared in support of the industry effort to standardize nuclear plant designs. These volumes describe the Combustion Engineering, Inc. System 80{sup +}{trademark} Standard Design. This volume 11 discusses Radiation Protection, Conduct of Operations, and the Initial Test Program.

  5. System 80+{trademark} Standard Design: CESSAR design certification. Volume 7: Amendment I

    Energy Technology Data Exchange (ETDEWEB)

    1990-12-21

    This report, entitled Combustion Engineering Standard Safety Analysis Report - Design Certification (CESSAR-DC), has been prepared in support of the industry effort to standardize nuclear plant designs. These documents describe the Combustion Engineering, Inc. System 80+{sup TM} Standard Design. This report, Volume 7, in conjunction with Volume 6, provides a description of engineered safety features.

  6. System 80+{trademark} Standard Design: CESSAR design certification. Volume 6: Amendment I

    Energy Technology Data Exchange (ETDEWEB)

    1990-12-21

    This report, entitled Combustion Engineering Standard Safety Analysis Report - Design Certification (CESSAR-DC), has been prepared in support of the industry effort to standardize nuclear plant designs. These documents describe the Combustion Engineering, Inc. System 80+{sup TM} Standard Design. This report, Volume 6, in conjunction with Volume 7, provides a description of engineered safety features.

  7. A prospective study of OAR volume variations between two different treatment planning systems in radiotherapy

    Directory of Open Access Journals (Sweden)

    Bhudevi Soubhagya Kulkarni

    2015-09-01

    Full Text Available Purpose: It has been seen that there is a clinically significant variation in the volume calculated across different planning systems for the same digital imaging and communication (DICOM contours.The purpose of this study is to investigate the difference in volumes of organs at risk when the structure sets were exported from the Eclipse ((Palo Alto, USA Version 10.0 to XIO CMS (Electa, Crawley, UK Version 4.40.00 treatment planning system (TPS and identify how the differences occur. Methods: We prospectively analyzed the volumes of organs at risk from computerized tomography (CT data of 54 patients. Head and neck and brain tumors were taken for this study and contoured on Eclipse treatment planning system (TPS after importing images from CT. These contoured images were then exported using radiotherapy DICOM transfer facility to XIO CMS planning system and compared the contoured volumes with Eclipse TPS structured volumes. Results: Our analysis showed that the differences in calculated volumes of the contours for the patients between the two planning systems can be large. Mixed results are shown for different organs with the absolute volume difference ranging from -0.25 cc to 319.73 cc. These results clearly shown that the two TPS interprets the contours differently when calculating the volume, and there is a closer match with the theoretical calculated volumes with XIO CMS calculated volumes. Conclusion: Observed discrepancies were consistent between the two planning systems. This impact of contouring variability could play a role on plan quality metrics which is used as criteria for clinical trial protocol compliance.

  8. The accuracy and optimal slice thickness of multislice helical computed tomography for right and left ventricular volume measurement

    Institute of Scientific and Technical Information of China (English)

    崔炜; 近藤武; 安野泰史; 郭玉印; 佐藤贵久; 皿井正義; 篠崎仁史; 柿澤聡士; 杉浦厚司; 大岛慶太; 片田和廣; 菱田仁

    2004-01-01

    Background Multislice helical computed tomography (MSCT) has been used to depict coronary anatomy noninvasively, and proved useful for evaluating ventricular function. The aim of our study was to assess the accuracy of ventricular volume as measured by MSCT. Methods Fourteen human left ventricular (LV) and 15 right ventricular (RV) casts were scanned by MSCT. A series of LV and RV short-axis images were reconstructed later with slice thickness of 2.0 mm, 3.5 mm, 5.0 mm, 7.0 mm, and 10.0 mm. Ventricular volume was calculated by the multislice tomographic Simpson's method. True LV and RV cast volumes were determined by water displacement. Results Both calculated LV and RV volumes correlated highly with the corresponding true volumes (all r>0.95, P<0.01). But with slice thickness from 2.0 mm to 10.0 mm, MSCT scanning overestimated the corresponding true volume by (3.21±5.95) ml to (12.58±8.56) ml for LV and (10.22±8.45) ml to (23.91±12.24) ml for RV (all P<0.01). There was a very high correlation between the overestimation and the selected slice thickness for both LV and RV volume measurements (r=0.998 and 0.996, P<0.01, respectively). However, when slice thickness was reduced to 5.0 mm, the overestimation for both LV and RV volume measurements became nonsignificant for slice thickness from 2.0 mm to 5.0 mm. Conclusions Both LV and RV volumes can be accurately estimated by MSCT. Thinner slice has more accurate calculated volume. However, 5.0 mm slice thickness is thin enough for an accurate measurement of LV or RV volume.

  9. Development of Parametric Mass and Volume Models for an Aerospace SOFC/Gas Turbine Hybrid System

    Science.gov (United States)

    Tornabene, Robert; Wang, Xiao-yen; Steffen, Christopher J., Jr.; Freeh, Joshua E.

    2005-01-01

    In aerospace power systems, mass and volume are key considerations to produce a viable design. The utilization of fuel cells is being studied for a commercial aircraft electrical power unit. Based on preliminary analyses, a SOFC/gas turbine system may be a potential solution. This paper describes the parametric mass and volume models that are used to assess an aerospace hybrid system design. The design tool utilizes input from the thermodynamic system model and produces component sizing, performance, and mass estimates. The software is designed such that the thermodynamic model is linked to the mass and volume model to provide immediate feedback during the design process. It allows for automating an optimization process that accounts for mass and volume in its figure of merit. Each component in the system is modeled with a combination of theoretical and empirical approaches. A description of the assumptions and design analyses is presented.

  10. Waste assay and mass balance for the decontamination and volume reduction system at LANL

    Energy Technology Data Exchange (ETDEWEB)

    Gruetzmacher, Kathleen M.; Ferran, Scott G.; Garner, Scott E.; Romero, Mike J.; Christensen, Davis V.; Bustos, Roland M.

    2003-07-01

    The Decontamination and Volume Reduction System (DVRS) operated by the Solid Waste Operations (SWO) Group at Los Alamos National Laboratory (LANL) processes large volume, legacy radioactive waste items. Waste boxes, in sizes varying from 4 ft x 4 ft x 8 ft to 10 ft x 12 ft x 40 ft, are assayed prior to entry into the processing building. Inside the building, the waste items are removed from their container, decontaminated and/or size reduced if necessary, and repackaged for shipment to the Waste Isolation Pilot Plant (WIPP) or on-site low-level waste disposal. The repackaged items and any secondary waste produced (e.g., personal protective equipment) are assayed again at the end of the process and a mass balance is done to determine whether there is any significant hold-up material left in the DVRS building. The DVRS building is currently classed as a radiological facility, with a building limit of 0.52 Ci of Pu239 and Am241, and 0.62 Ci of Pu238, the most common radionuclides processed. This requires tight controls on the flow of nuclear material. The large volume of the initial waste packages, the (relatively) small amounts of radioactive material in them, and the tight ceiling on the building inventory require accurate field measurements of the nuclear material. This paper describes the radioactive waste measurement techniques, the computer modeling used to determine the amount of nuclear material present in a waste package, the building inventory database, and the DVRS process itself. Future plans include raising the limit on the nuclear material inventory allowed in the building to accommodate higher activity waste packages. All DOE sites performing decontamination and decommissioning of radioactive process equipment face challenges related to waste assay and inventory issues. This paper describes an ongoing operation, incorporating lessons learned over the life of the project to date.

  11. Bayesian characterization of multiple-slope sound energy decays in coupled-volume systems.

    Science.gov (United States)

    Xiang, Ning; Goggans, Paul; Jasa, Tomislav; Robinson, Philip

    2011-02-01

    Due to recent developments in concert hall design, there is an increasing interest in the analysis of sound energy decays consisting of multiple exponential decay rates. It has been considered challenging to estimate parameters associated with double-rate (slope) decay characteristics, and even more challenging when the coupled-volume systems contain more than two decay processes. To meet the need of characterizing energy decays of multiple decay processes, this work investigates coupled-volume systems using acoustic scale-models of three coupled rooms. Two Bayesian formulations are compared using the experimentally measured sound energy decay data. A fully parameterized Bayesian formulation has been found to be capable of characterization of multiple-slope decays beyond the single-slope and double-slope energy decays. Within the Bayesian framework using this fully parameterized formulation, an in-depth analysis of likelihood distributions over multiple-dimensional decay parameter space motivates the use of Bayesian information criterion, an efficient approach to solving Bayesian model selection problems that are suitable for estimating the number of exponential decays. The analysis methods are then applied to a geometric-acoustics simulation of a conceptual concert hall. Sound energy decays more complicated than single-slope and double-slope nature, such as triple-slope decays have been identified and characterized.

  12. Ocular microtremor measurement system: design and performance.

    Science.gov (United States)

    Sheahan, N F; Coakley, D; Hegarty, F; Bolger, C; Malone, J

    1993-05-01

    The frequency of ocular microtremor (OMT) is related to the functional status of the brain stem, and thus OMT may be useful in the diagnosis and management of brain stem disorders. The paper discusses the design of an OMT measurement system and reports quantitative specifications for three portable systems. All systems use a piezo-electric element as the transducer, which measures the displacement of the sclera during eye rotations. The systems differ in the manner in which the signal is recorded. All systems can detect eye movements corresponding to displacements of the sclera ranging from 12 to over 3000 nm. The frequency responses of all systems are flat (< 2 dB deviation from peak response) between 20 and 150 Hz. The phase response shows deviations (< pi) at the extremes of this range, but qualitative comparison of input and measured signals demonstrates that phase distortion is not excessive. Thus all systems are acceptable for clinical studies involving OMT.

  13. Turbine gas temperature measurement and control system

    Science.gov (United States)

    Webb, W. L.

    1973-01-01

    A fluidic Turbine Inlet Gas Temperature (TIGIT) Measurement and Control System was developed for use on a Pratt and Whitney Aircraft J58 engine. Based on engine operating requirements, criteria for high temperature materials selection, system design, and system performance were established. To minimize development and operational risk, the TIGT control system was designed to interface with an existing Exhaust Gas Temperature (EGT) Trim System and thereby modulate steady-state fuel flow to maintain a desired TIGT level. Extensive component and system testing was conducted including heated (2300F) vibration tests for the fluidic sensor and gas sampling probe, temperature and vibration tests on the system electronics, burner rig testing of the TIGT measurement system, and in excess of 100 hours of system testing on a J58 engine. (Modified author abstract)

  14. Measuring Fiscal Capacity of School Systems.

    Science.gov (United States)

    Green, Harry A.

    Ways of measuring the fiscal capacity of school systems are examined in this paper, which presents a representative tax system model. Fiscal capacity is influenced by factors other than tax base size; the "ideal" model should address adjustments for variations in cost across communities and school systems. The first section examines the…

  15. The NIST Primary Radon-222 Measurement System

    OpenAIRE

    Collé, R.; Hutchinson, J. M. R.; Unterweger, M. P.

    1990-01-01

    Within the United States, the national standard for radon measurements is embodied in a primary radon measurement system that has been maintained for over 50 years to accurately measure radon (222Rn) against international and national radium (226Ra) standards. In turn, all of the radon measurements made at the National Institute of Standards and Technology (NIST) and the radon transfer calibration standards and calibration services provided by NIST are directly related to this national radon ...

  16. Measurement of tumor volumes of hepatocellular carcinoma (HCC) by computed tomography (CT). Correlation with several tumor markers

    Energy Technology Data Exchange (ETDEWEB)

    Yoneshima, Manabu; Sawabu, Norio; Toya, Daishu

    1984-09-01

    Tumor volumes of HCC were measured by CT using planimeter and the clinical value of this measurement was evaluated by comparing several tumor markers. Tumor volumes measured by CT roughly agreed with those measured by angiography. In some cases, volumes from ultrasonography were smaller than those from CT and angiography. Tumor volumes measured by CT correlated significantly with the levels of ..cap alpha..-fetoprotein (AFP) but didn't relate to the presence of hepatoma specific ..gamma..-GTP isoenzyme (novel ..gamma..-GTP) nor to the values and positivities of LAI assay. In small HCCs (<=30 cm/sup 3/), the presence of novel ..gamma..-GTP and the levels of AFP were significantly lower than for larger tumors of HCC, but LAI assay wasn't lower. The non-tumorous volumes and the ratio of the non-tumorous volume to the whole liver volume didn't relate to the tests of liver function except for the presence of ascites.

  17. Importance of evaluation of uncertainties on the measurement of natural gas and petroleum volumes; Importancia da avaliacao das incertezas na medicao dos volumes de petroleo e gas natural

    Energy Technology Data Exchange (ETDEWEB)

    Silva Filho, Jose Alberto Pinheiro da; Oliveira, Thiago Barra Vidal de; Mata, Josaphat Dias da [PETROBRAS, Rio de Janeiro, RJ (Brazil)], Emails: jose.pinheiro@petrobras.com.br, thiagovidal@petrobras.com.br, josaphat@petrobras.com.br; Val, Luiz Gustavo do [Instituto de Qualidade e Metrologia (IQM), Rio de Janeiro, RJ (Brazil)], E-mail: gdoval.iqm@petrobras.com.br

    2009-07-01

    The measurement is considered as the 'cash register' of the enterprises, increasing the accuracy and the exigence at each step when come close to the delivery points, where the 0.1 % of differences are discussed. The work presents the approach used in the evaluation of measurement uncertainties in the volumes obtained of petroleum and natural gas at the processes of production in Brazil, and in the international level as well.

  18. Management control and status reports documentation standard and Data Item Descriptions (DID). Volume of the information system life-cycle and documentation standards, volume 5

    Science.gov (United States)

    Callender, E. David; Steinbacher, Jody

    1989-01-01

    This is the fifth of five volumes on Information System Life-Cycle and Documentation Standards. This volume provides a well organized, easily used standard for management control and status reports used in monitoring and controlling the management, development, and assurance of informations systems and software, hardware, and operational procedures components, and related processes.

  19. Assurance specification documentation standard and Data Item Descriptions (DID). Volume of the information system life-cycle and documentation standards, volume 4

    Science.gov (United States)

    Callender, E. David; Steinbacher, Jody

    1989-01-01

    This is the fourth of five volumes on Information System Life-Cycle and Documentation Standards. This volume provides a well organized, easily used standard for assurance documentation for information systems and software, hardware, and operational procedures components, and related processes. The specifications are developed in conjunction with the corresponding management plans specifying the assurance activities to be performed.

  20. Management plan documentation standard and Data Item Descriptions (DID). Volume of the information system life-cycle and documentation standards, volume 2

    Science.gov (United States)

    Callender, E. David; Steinbacher, Jody

    1989-01-01

    This is the second of five volumes of the Information System Life-Cycle and Documentation Standards. This volume provides a well-organized, easily used standard for management plans used in acquiring, assuring, and developing information systems and software, hardware, and operational procedures components, and related processes.

  1. System Entropy Measurement of Stochastic Partial Differential Systems

    Directory of Open Access Journals (Sweden)

    Bor-Sen Chen

    2016-03-01

    Full Text Available System entropy describes the dispersal of a system’s energy and is an indication of the disorder of a physical system. Several system entropy measurement methods have been developed for dynamic systems. However, most real physical systems are always modeled using stochastic partial differential dynamic equations in the spatio-temporal domain. No efficient method currently exists that can calculate the system entropy of stochastic partial differential systems (SPDSs in consideration of the effects of intrinsic random fluctuation and compartment diffusion. In this study, a novel indirect measurement method is proposed for calculating of system entropy of SPDSs using a Hamilton–Jacobi integral inequality (HJII-constrained optimization method. In other words, we solve a nonlinear HJII-constrained optimization problem for measuring the system entropy of nonlinear stochastic partial differential systems (NSPDSs. To simplify the system entropy measurement of NSPDSs, the global linearization technique and finite difference scheme were employed to approximate the nonlinear stochastic spatial state space system. This allows the nonlinear HJII-constrained optimization problem for the system entropy measurement to be transformed to an equivalent linear matrix inequalities (LMIs-constrained optimization problem, which can be easily solved using the MATLAB LMI-toolbox (MATLAB R2014a, version 8.3. Finally, several examples are presented to illustrate the system entropy measurement of SPDSs.

  2. Equations of bark thickness and volume profiles at different heights with easy-measurement variables

    Energy Technology Data Exchange (ETDEWEB)

    Cellini, J. M.; Galarza, M.; Burns, S. L.; Martinez-Pastur, G. J.; Lencinas, M. V.

    2012-11-01

    The objective of this work was to develop equations of thickness profile and bark volume at different heights with easy-measurement variables, taking as a study case Nothofagus pumilio forests, growing in different site qualities and growth phases in Southern Patagonia. Data was collected from 717 harvested trees. Three models were fitted using multiple, non-lineal regression and generalized linear model, by stepwise methodology, iteratively reweighted least squares method for maximum likelihood estimation and Marquardt algorithm. The dependent variables were diameter at 1.30 m height (DBH), relative height (RH) and growth phase (GP). The statistic evaluation was made through the adjusted determinant coefficient (r2-adj), standard error of the estimation (SEE), mean absolute error and residual analysis. All models presented good fitness with a significant correlation with the growth phase. A decrease in the thickness was observed when the relative height increase. Moreover, a bark coefficient was made to calculate volume with and without bark of individual trees, where significant differences according to site quality of the stands and DBH class of the trees were observed. It can be concluded that the prediction of bark thickness and bark coefficient is possible using DBH, height, site quality and growth phase, common and easy measurement variables used in forest inventories. (Author) 23 refs.

  3. Simulation method for cardiac stroke volume estimation by intracardiac electrical impedance measurement.

    Science.gov (United States)

    Barak, C; Leviatan, Y; Inbar, G F; Hoekstein, K N

    1992-09-01

    Using the electrical impedance measurement technique to investigate stroke volume estimation, three models of the ventricle were simulated. A four-electrode impedance catheter was used; two electrodes to set up an electric field in the model and the other two to measure the potential difference. A new approach, itself an application of the quasi-static case of a method used to solve electromagnetic field problems, was used to solve the electric field in the model. The behaviour of the estimation is examined with respect to the electrode configuration on the catheter and to catheter location with respect to the ventricle walls. Cardiac stroke volume estimation was found to be robust to catheter location generating a 10 per cent error for an offset of 40 per cent of the catheter from the chamber axis and rotation of 20 degrees with respect to the axis. The electrode configuration has a dominant effect on the sensitivity and accuracy of the estimation. Certain configurations gave high accuracy, whereas in others high sensitivity was found with lower accuracy. This led to the conclusion that the electrode configuration should be carefully chosen according to the desired criteria.

  4. Accurate measurement of volume and shape of resting and activated blood platelets from light scattering

    Science.gov (United States)

    Moskalensky, Alexander E.; Yurkin, Maxim A.; Konokhova, Anastasiya I.; Strokotov, Dmitry I.; Nekrasov, Vyacheslav M.; Chernyshev, Andrei V.; Tsvetovskaya, Galina A.; Chikova, Elena D.; Maltsev, Valeri P.

    2013-01-01

    We introduce a novel approach for determination of volume and shape of individual blood platelets modeled as an oblate spheroid from angle-resolved light scattering with flow-cytometric technique. The light-scattering profiles (LSPs) of individual platelets were measured with the scanning flow cytometer and the platelet characteristics were determined from the solution of the inverse light-scattering problem using the precomputed database of theoretical LSPs. We revealed a phenomenon of parameter compensation, which is partly explained in the framework of anomalous diffraction approximation. To overcome this problem, additional a priori information on the platelet refractive index was used. It allowed us to determine the size of each platelet with subdiffraction precision and independent of the particular value of the platelet aspect ratio. The shape (spheroidal aspect ratio) distributions of platelets showed substantial differences between native and activated by 10 μM adenosine diphosphate samples. We expect that the new approach may find use in hematological analyzers for accurate measurement of platelet volume distribution and for determination of the platelet activation efficiency.

  5. Accurate measurement of volume and shape of resting and activated blood platelets from light scattering.

    Science.gov (United States)

    Moskalensky, Alexander E; Yurkin, Maxim A; Konokhova, Anastasiya I; Strokotov, Dmitry I; Nekrasov, Vyacheslav M; Chernyshev, Andrei V; Tsvetovskaya, Galina A; Chikova, Elena D; Maltsev, Valeri P

    2013-01-01

    We introduce a novel approach for determination of volume and shape of individual blood platelets modeled as an oblate spheroid from angle-resolved light scattering with flow-cytometric technique. The light-scattering profiles (LSPs) of individual platelets were measured with the scanning flow cytometer and the platelet characteristics were determined from the solution of the inverse light-scattering problem using the precomputed database of theoretical LSPs. We revealed a phenomenon of parameter compensation, which is partly explained in the framework of anomalous diffraction approximation. To overcome this problem, additional a priori information on the platelet refractive index was used. It allowed us to determine the size of each platelet with subdiffraction precision and independent of the particular value of the platelet aspect ratio. The shape (spheroidal aspect ratio) distributions of platelets showed substantial differences between native and activated by 10 μM adenosine diphosphate samples. We expect that the new approach may find use in hematological analyzers for accurate measurement of platelet volume distribution and for determination of the platelet activation efficiency.

  6. The effects of renal variation upon measurements of perfusion and leakage volume in breast tumours

    Science.gov (United States)

    Ahearn, T. S.; Staff, R. T.; Redpath, T. W.; Semple, S. I. K.

    2004-05-01

    Dynamic contrast enhanced MRI (DCE-MRI) and pharmacokinetic models have been used to measure tumour permeability (Ktrans) and leakage volume (ve) in numerous studies. The construction of pharmacokinetic models describing such tissue properties relies on defining the blood plasma concentration of contrast agent with respect to time (Cp(t)). When direct measurement is not possible a bi-exponential decay has been applied using data from healthy volunteers. This work investigates, by simulation, the magnitude of errors resulting from this definition with respect to normal variation in renal function and for cases with renal impairment. Errors up to 23% in ve and 28% in Ktrans were found for the normal simulations, and 67% in ve and 61% in Ktrans for the impaired simulations. If this bi-exponential curve is used as an input function to the generalized kinetic model and used in oncology, estimates of tissue permeability and leakage volume will possess large errors due to variation in Cp(t) curves between subjects.

  7. Measurement of Single Cell Refractive Index, Dry Mass, Volume, and Density Using a Transillumination Microscope

    Science.gov (United States)

    Phillips, Kevin G.; Jacques, Steven L.; McCarty, Owen J. T.

    2012-09-01

    Phase contrast microscopy has become ubiquitous in the field of biology, particularly in qualitative investigations of cellular morphology. However, the use of quantitative phase retrieval methods and their connection to cellular refractive index and dry mass density remain under utilized. This is due in part to the restriction of phase and cellular mass determination to custom built instruments, involved mathematical analysis, and prohibitive sample perturbations. We introduce tomographic bright field imaging, an accessible optical imaging technique enabling the three dimensional measurement of cellular refractive index and dry mass density using a standard transillumination optical microscope. The validity of the technique is demonstrated on polystyrene spheres. The technique is then applied to the measurement of the refractive index, dry mass, volume, and density of red blood cells. This optical technique enables a simple and robust means to perform quantitative investigations of engineered and biological specimens in three dimensions using standard optical microscopes.

  8. Measurement of slice thickness using partial volume effect in MR imaging

    Energy Technology Data Exchange (ETDEWEB)

    Higashida, Mitsuji; Yamazaki, Masaru [Osaka City Univ. (Japan). Hospital; Ogura, Akio; Inoue, Hiroshi; Hongou, Takaharu

    1998-08-01

    The NEMA standard and AAPM method have been approved for the determination of slice thickness in diagnostic magnetic resonance imaging. In these methods, the slice thickness is obtained as the full width at half maximum of the slice profile. However, these methods are affected by the signal-to-noise ratio (SNR) and pixel size. In addition, the measurement procedure required for accurate evaluation is troublesome. Therefore, a new method of evaluation using the partial volume effect, called the PVE method, is proposed. With the PVE method, slice thickness can be evaluated without the slice profile. A comparison of accuracy and simplicity of measurement is made between the PVE method and the wedge method of the NEMA standard. Results showed the PVE method to be accurate and easier to use than the wedge method. (author)

  9. Anatomic guidelines defined by reformatting images on MRI for volume measurement of amygdala and hippocampus

    Energy Technology Data Exchange (ETDEWEB)

    Hoshida, Tohru; Sakaki, Toshisuke [Nara Medical Univ., Kashihara (Japan); Uematsu, Sumio

    1995-03-01

    Twelve patients with intractable partial epilepsy underwent MR scans at the Epilepsy Center of the Johns Hopkins Hospital. There were five women and seven men, ranging in age from five to 51 years (mean age: 26 years). Coronal images were obtained using a 3-D SPGR. The coronal images were transferred to an Allegro 5.1 workstation, and reformatted along the cardinal axes (axial and sagittal) in multiple view points. The anterior end of the amygdala was measured at the level just posterior to the disappearance of the temporal stem. The semilunar gyrus of the amygdala was separated from the ambient gyrus by the semianular sulcus that forms the boundary between the amygdala and the entorhinal cortex. The delineation of the hippocampal formation included the subicular complex, hippocampal proper, dentate gyrus, alveus, and fimbria. The uncal cleft separated the uncus above from the parahippocampal gyrus below. The roof of this cleft was formed by the hippocampus and the dentate gyrus, and the floor, by the presubiculum and subiculum. Although using some guidelines, strictly separating the hippocampal head from the posterior part of the amygdala was not feasible as was previously reported, because of the isointensity on MRI between the cortex of the amygdala and the hippocampus. The most posterior portion of the hippocampus was measured at the level of the subsplenial gyri, just below the splenium of the corpus callosum, to measure the hippocampal volume in its near totality. Therefore, it is reliable, and clinically useful, to measure the combined total volume of the amygdala and the hippocampus when comparing results with those of other centers. (S.Y.).

  10. Accuracy and Consistency of Respiratory Inductive Plethysmography for Overnight Tidal Volume Measurement

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    To validate the accuracy and consistency of respiratory inductive plethysmography (RIP) in measuring tidal volume after an overnight sleep, tidal volumes of 18 patients with suspected sleep-disordered breathing and 8 normal volunteers were measured simultaneously with RIP (VTRIP) and with an ultrasonic airflow meter (VTUFM) before and after an unstrained overnight sleep on supine and lateral decubitus. The bias of the VTRIP was expressed as (VTRIP-VTUFM)/ VTUFM*100 %, limits of agreement between VTRIP and VTUFM was measured by averaged bias ±2 s. Results showed that in normal subjects, the bias of RIP before and after overnight sleep was precise and consistent in both supine (0.7 % and -1.6 %) and lateral decubitus (3.7 % and -0.56 %). In these patients, the bias of RIP before and after sleep in supine also remained small (1.9 % and 1.7 %), but it became larger in lateral decubitus (24.5 % and 20.4 %) and 11.5 % exceeded the limits of agreement observed in the evening. The patients′ body mass indices (BMI) were higher than those of normal subjects (median 34.2 vs. 27.8 kg/m2). Pooled data showed that the bias of VTRIP in the morning on lateral decubitus but not on supine was correlated to BMI (Spearman R=0.32, n=52, P=0.02). Thus, we were led to conclude that the accuracy of VTRIP overnight was precise and consistent in normal subjects, but the deviation of VTRIP measured on lateral decubitus in patients especially in those with excessive obesity was greater, thus, the method should not be used for quantitative determination.

  11. Wind energy conversion. Volume IV. Drive system dynamics

    Energy Technology Data Exchange (ETDEWEB)

    Martinez-Sanchez, M.; Labuszewski, T.

    1978-09-01

    The dynamics of the drive system and various approaches to power transmission are described. The effects on performance of using a constant rotor speed as opposed to a rotor speed varying with the wind speed are discussed for various rotor operating schedules and typical wind distributions. The dynamics of the combined rotor, alternator, and drive system are analyzed. Conditions which could lead to electro-dynamic instabilities and desynchronization are discussed as well as means for stabilizing the system. The dynamics of the drive system and important design conditions for various drive systems are discussed, such as location of the alternators, use of hydraulic drive systems and smoothing techniques.

  12. Limitations and pitfalls in measurements of right ventricular stroke volume in an animal model of right heart failure.

    Science.gov (United States)

    Vildbrad, Mads Dam; Andersen, Asger; Andersen, Thomas Krarup; Axelgaard, Sofie; Holmboe, Sarah; Andersen, Stine; Ringgaard, Steffen; Nielsen-Kudsk, Jens Erik

    2015-05-01

    Right heart failure occurs in various heart and pulmonary vascular diseases and may be fatal. We aimed to identify limitations in non-invasive measurements of right ventricular stroke volume in an animal model of right ventricular failure. Data from previous studies randomising rats to pulmonary trunk banding (PTB, n = 33) causing pressure-overload right ventricular failure or sham operation (n = 16) was evaluated retrospectively. We measured right ventricular stroke volume by high frequency echocardiography and magnetic resonance imaging (MRI). We found correlation between right ventricular stroke volume measured by echocardiography and MRI in the sham animals (r = 0.677, p = 0.004) but not in the PTB group. Echocardiography overestimated the stroke volume compared to MRI in both groups. Intra- and inter-observer variation did not explain the difference. Technical, physiological and anatomical issues in the pulmonary artery might explain why echocardiography over-estimates stroke volume. Flow acceleration close to the pulmonary artery banding can cause uncertainties in the PTB model and might explain the lack of correlation. In conclusion, we found a correlation in right ventricular stroke volume measured by echocardiography versus MRI in the sham group but not the PTB group. Echocardiography overestimated right ventricular stroke volume compared to MRI.

  13. Measurement of and Factors Associated with the Anterior Chamber Volume in Healthy Chinese Adults

    Directory of Open Access Journals (Sweden)

    Yuan Zong

    2017-01-01

    Full Text Available Purpose. To measure the anterior chamber volume (ACV and determine factors associated with the ACV in healthy Chinese adults. Methods. In this cross-sectional study, we used swept-source optical coherence tomography (SS-OCT to measure ACV and other anterior segment parameters. Factors associated with ACV were also determined. Results. A total of 313 healthy Chinese adults were enrolled. The anterior segment parameters, including ACV, could be measured by SS-OCT with excellent repeatability and reproducibility. There was a significant difference between the horizontal and vertical anterior chamber widths (ACW (P<0.05, with a mean difference of 390 μm. The ACV (mean 153.83±32.42 mm3 was correlated with most of the anterior segment parameters, especially anterior chamber depth (ACD, which accounted for about 85% of the variation of ACV. Most of the anterior segment parameters were significantly correlated with age, and the relative changes in ACV and ACD were greatest in subjects aged 41–50 years. Conclusion. ACV was correlated with most of the anterior segment parameters measured in this study, particularly ACD. The relatively large difference between horizontal and vertical ACW suggests that the ACV could and should be measured using multiple OCT scans.

  14. Measurement of and Factors Associated with the Anterior Chamber Volume in Healthy Chinese Adults.

    Science.gov (United States)

    Zong, Yuan; Xu, Qian; Jiang, Chunhui; Zhu, Haohao; Yu, Jian; Sun, Xinghuai

    2017-01-01

    Purpose. To measure the anterior chamber volume (ACV) and determine factors associated with the ACV in healthy Chinese adults. Methods. In this cross-sectional study, we used swept-source optical coherence tomography (SS-OCT) to measure ACV and other anterior segment parameters. Factors associated with ACV were also determined. Results. A total of 313 healthy Chinese adults were enrolled. The anterior segment parameters, including ACV, could be measured by SS-OCT with excellent repeatability and reproducibility. There was a significant difference between the horizontal and vertical anterior chamber widths (ACW) (P ACV (mean 153.83 ± 32.42 mm(3)) was correlated with most of the anterior segment parameters, especially anterior chamber depth (ACD), which accounted for about 85% of the variation of ACV. Most of the anterior segment parameters were significantly correlated with age, and the relative changes in ACV and ACD were greatest in subjects aged 41-50 years. Conclusion. ACV was correlated with most of the anterior segment parameters measured in this study, particularly ACD. The relatively large difference between horizontal and vertical ACW suggests that the ACV could and should be measured using multiple OCT scans.

  15. Theoretical test of Jarzynski's equality for reversible volume-switching processes of an ideal gas system.

    Science.gov (United States)

    Sung, Jaeyoung

    2007-07-01

    We present an exact theoretical test of Jarzynski's equality (JE) for reversible volume-switching processes of an ideal gas system. The exact analysis shows that the prediction of JE for the free energy difference is the same as the work done on the gas system during the reversible process that is dependent on the shape of path of the reversible volume-switching process.

  16. Satellite power systems (SPS) concept definition study. Volume 7: SPS program plan and economic analysis, appendixes

    Science.gov (United States)

    Hanley, G.

    1978-01-01

    Three appendixes in support of Volume 7 are contained in this document. The three appendixes are: (1) Satellite Power System Work Breakdown Structure Dictionary; (2) SPS cost Estimating Relationships; and (3) Financial and Operational Concept. Other volumes of the final report that provide additional detail are: Executive Summary; SPS Systems Requirements; SPS Concept Evolution; SPS Point Design Definition; Transportation and Operations Analysis; and SPS Technology Requirements and Verification.

  17. Multiple IMU system hardware interface design, volume 2

    Science.gov (United States)

    Landey, M.; Brown, D.

    1975-01-01

    The design of each system component is described. Emphasis is placed on functional requirements unique in this system, including data bus communication, data bus transmitters and receivers, and ternary-to-binary torquing decision logic. Mechanization drawings are presented.

  18. Analysis of measurement system as the mechatronics system

    Science.gov (United States)

    Giniotis, V.; Grattan, K. T. V.; Rybokas, M.; Bručas, D.

    2010-07-01

    The paper deals with the mechatronic arrangement for angle measuring system application. The objects to be measured are the circular raster scales, rotary encoders and coded scales. The task of the measuring system is to determine the bias of angle measuring standard as the circular scale and to use the results for the error correction and accuracy improvement of metal cutting machines, coordinate measuring machines, robots, etc. The technical solutions are given with the application of active materials for smart piezoactuators implemented into the several positions of angular measuring equipment. Mechatronic measuring system is analysed as complex integrated system and some of its elements can be used as separate units. All these functional elements are described and commented in the paper with the diagrams and graphs of errors and examples of microdisplacement devices using the mechatronic elements.

  19. Analysis of measurement system as the mechatronics system

    Energy Technology Data Exchange (ETDEWEB)

    Giniotis, V [Institute of Geodesy, Vilnius Gediminas Technical University, Vilnius, Lithuania, Sauletekio al. 11, 10223 Vilnius-40, Lithuania, Fax: 370 5 2744 705 (Lithuania); Grattan, K T V [School of Engineering and Mathematical Sciences Electrical, Electronic and Information Eng, City University, Northampton Square, London EC1V 0HB (United Kingdom); Rybokas, M [Department of Information Technologies, Vilnius Gediminas Technical University, Sauletekio al. 11, 10223 Vilnius-40, Lithuania, Fax: 370 5 2744 705 (Lithuania); Brucas, D, E-mail: gi@ap.vtu.l, E-mail: k.t.v.grattan@city.ac.u, E-mail: MRybokas@gama.l, E-mail: domka@ktv.l, E-mail: vg@ai.vgtu.l [Department of Geodesy and Cadastre, Vilnius Gediminas Technical University, Vilnius, Lithuania Sauletekio al. 11, 10223 Vilnius-40, Lithuania, Fax: 370 5 2744 705 (Lithuania)

    2010-07-01

    The paper deals with the mechatronic arrangement for angle measuring system application. The objects to be measured are the circular raster scales, rotary encoders and coded scales. The task of the measuring system is to determine the bias of angle measuring standard as the circular scale and to use the results for the error correction and accuracy improvement of metal cutting machines, coordinate measuring machines, robots, etc. The technical solutions are given with the application of active materials for smart piezoactuators implemented into the several positions of angular measuring equipment. Mechatronic measuring system is analysed as complex integrated system and some of its elements can be used as separate units. All these functional elements are described and commented in the paper with the diagrams and graphs of errors and examples of microdisplacement devices using the mechatronic elements.

  20. Dynamic Properties of Impulse Measuring Systems

    DEFF Research Database (Denmark)

    Pedersen, A.; Lausen, P.

    1971-01-01

    After some basic considerations the dynamic properties of the measuring system are subjected to a general examination based on a number of responses, characteristic of the system. It is demonstrated that an impulse circuit has an internal impedance different from zero, for which reason the intera......After some basic considerations the dynamic properties of the measuring system are subjected to a general examination based on a number of responses, characteristic of the system. It is demonstrated that an impulse circuit has an internal impedance different from zero, for which reason...

  1. Preparation Measurements and Assessment of Roof Systems

    Directory of Open Access Journals (Sweden)

    Baláž Richard

    2014-11-01

    Full Text Available The Institute of Architectural Engineering at the Civil Engineering Faculty TU of Kosice, in its ongoing research, aims to monitor the physical properties of building envelope structures with emphasis placed on hydrothermal problems, at present. The research focuses on the assembly of equipment in climate chambers with their respective sample envelopes and fenestration systems, which are involved in a measuring experiment. The prime aim is to design a logical and transparent system for gathering, evaluating and storing hydrothermal related data. This contribution further illustrates the embedding system of measurement points in installed samples and the system of monitoring their physical properties over an annual period.

  2. Preparation Measurements and Assessment of Roof Systems

    Science.gov (United States)

    Baláž, Richard; Bagoňa, Miloslav

    2014-11-01

    The Institute of Architectural Engineering at the Civil Engineering Faculty TU of Kosice, in its ongoing research, aims to monitor the physical properties of building envelope structures with emphasis placed on hydrothermal problems, at present. The research focuses on the assembly of equipment in climate chambers with their respective sample envelopes and fenestration systems, which are involved in a measuring experiment. The prime aim is to design a logical and transparent system for gathering, evaluating and storing hydrothermal related data. This contribution further illustrates the embedding system of measurement points in installed samples and the system of monitoring their physical properties over an annual period.

  3. Three-component laser anemometer measurement systems

    Science.gov (United States)

    Goldman, Louis J.

    1991-01-01

    A brief overview of the different laser anemometer (LA) optical designs available is presented. Then, the LA techniques that can be used to design a three-component measurement system for annular geometries are described. Some of the facility design considerations unique to these LA systems are also addressed. Following this, the facilities and the LA systems that were used to successfully measure the three components of velocity in the blading of annular-flow machines are reviewed. Finally, possible LA system enhancements and future research directions are presented.

  4. SIMS: The SLAC Industrial Measurement System

    Energy Technology Data Exchange (ETDEWEB)

    Bell, B.; /SLAC

    2005-08-12

    The development of electronic sensors and of small powerful computers, and their integration together have led to the development of what has come to be known as Industrial Measurement Technology (IMT). Industrial Measurement Systems feature one or more electronic sensors and a computer with powerful software. The software has three essential components: data collection, data reduction and data analysis. In the field of industrial surveying, the IMT system is the automated theodolite system, but other systems such as the laser tracker are on the horizon.

  5. TPX: Contractor preliminary design review. Volume 2, PF systems engineering

    Energy Technology Data Exchange (ETDEWEB)

    Calvin, H.A. [Lawrence Livermore National Lab., CA (United States)

    1995-07-28

    This system development specification covers the Poloidal Field (PF) Magnet System, WBS 14 in the Princeton Plasma Physics Laboratory TPX Program to build a tokamak fusion reactor. This specification establishes the performance, design, development and test requirements of the PF Magnet System.

  6. TPX: Contractor preliminary design review. Volume 2, PF systems engineering

    Energy Technology Data Exchange (ETDEWEB)

    Calvin, H.A. [Lawrence Livermore National Lab., CA (United States)

    1995-07-28

    This system development specification covers the Poloidal Field (PF) Magnet System, WBS 14 in the Princeton Plasma Physics Laboratory TPX Program to build a tokamak fusion reactor. This specification establishes the performance, design, development and test requirements of the PF Magnet System.

  7. In situ calibrated defocusing PTV for wall-bounded measurement volumes

    Science.gov (United States)

    Fuchs, T.; Hain, R.; Kähler, C. J.

    2016-08-01

    In many situations, 3D velocity measurements in thin (∼1 mm) but wide (∼100  ×  100 mm2) flow channels is an important task. To resolve the in-plane and out-of-plane velocity gradients properly, a precise calibration is required, since 3D measurement approaches rely strongly on the accuracy of the calibration procedure. It is likely that calibration targets do not fit domains with small depths, due to their size. Furthermore, in fields where such measurements are of interest, the accessibility of the measurement volume is often limited or even impossible. To overcome these drawbacks, this paper introduces an in situ calibrated defocusing particle tracking velocimetry approach for wall-bounded measurement domains with depths in the low millimeter range. The calibration function for the particle depth location is directly derived from the particle image geometries and their displacements between two frames. Employing only a single camera, this defocusing approach is capable of measuring the air flow between two parallel glass plates at a distance of 1 mm with an average uncertainty of 2.43% for each track, relative to the maximum velocity. A tomographic particle tracking velocimetry measurement, serving as a benchmark for the single camera technique, reaches an average uncertainty of 1.59%. Altogether, with its straightforward set-up and without requiring a calibration target, this in situ calibrated defocusing approach opens new areas of application for optical flow velocimetry. In particular, for measurement domains with small optical windows and a lack of accessibility.

  8. Measurement system as a subsystem of the quality management system

    Directory of Open Access Journals (Sweden)

    Ľubica Floreková

    2006-12-01

    Full Text Available Each measurement system and a control principle must be based on certain facts about the system behaviour (what, operation (how and structure (why. Each system is distributed into subsystems that provide an input for the next subsystem. For each system, start is important the begin, that means system characteristics, collecting of data, its hierarchy and the processes distribution.A measurement system (based on the chapter 8 of the standard ISO 9001:2000 Quality management system, requirements defines the measurement, analysis and improvement for each organization in order to present the products conformity, the quality management system conformity guarantee and for the continuously permanent improvement of effectivity, efficiency and economy of quality management system.

  9. Volume magnetization for system-level testing of magnetic materials within small satellites

    Science.gov (United States)

    Gerhardt, David T.; Palo, Scott E.

    2016-10-01

    Passive Magnetic Attitude Control (PMAC) is a popular among small satellites due to its low resource cost and simplicity of installation. However, predicting the performance of these systems can be a challenge, chiefly due to the difficulty of measurement and simulation of hysteresis materials. We present a low-cost method of magnetic measurement allowing for characterization of both hard and soft magnetic materials. A Helmholtz cage uniformly magnetizes a 30 cm×30 cm×30 cm test volume. The addition of a thin sense coil allows this system to characterize individual hysteresis rod performance when in close proximity to other hard and/or soft magnetic materials. This test setup is applied to hard and soft magnetic materials used aboard the Colorado Student Space Weather Experiment (CSSWE), a 3U CubeSat for space weather investigation which used a PMAC system. The measured hard magnet dipole of 0.80±0.017 A m2 is in good agreement with the dynamics-based satellite dipole moment fits. Five hysteresis rods from the same set as the CSSWE flight rods are tested; significant differences in dampening abilities are found. In addition, a limitation of the widely-used Flatley model is described. The interaction of two hysteresis rods in a variety of relative geometries are tested; perpendicular rods are found to have no significant interaction while parallel rods could have their dampening ability reduced by half, depending on the rod separation distance. Finally, the performance of the hysteresis rods are measured in their flight configuration, with hard and soft magnetic material dispersed as it is on CSSWE itself. For the CSSWE PMAC system design, interactions between rods have a greater affect than the magnetic flux density offset due to the onboard bar magnet.

  10. Microwave Radiometry for Oil Pollution Monitoring, Measurements, and Systems

    DEFF Research Database (Denmark)

    Skou, Niels

    1986-01-01

    Work is presently carried out in Europe to change the Status of the microwave radiometer, namely, to develop it from a research instrument to an operational instrument-especially for measuring oil pollution on the sea surface. The Technical University of Denmark (TUD), with its long experience...... in airborne microwave radiometry, is heavily involved in this process. The TUD multichannel imaging radiometer system has been flown in several large-scale oil-pollution experiments, the collected data have been analyzed, and they have revealed that care must be exercised to obtain accurate oil volume...

  11. Coordination of Passive Systems under Quantized Measurements

    NARCIS (Netherlands)

    De Persis, Claudio; Jayawardhana, Bayu

    2012-01-01

    In this paper we investigate a passivity approach to collective coordination and synchronization problems in the presence of quantized measurements and show that coordination tasks can be achieved in a practical sense for a large class of passive systems.

  12. Measurement of photometric characteristics of daylighting systems

    Energy Technology Data Exchange (ETDEWEB)

    Aydinli, S.; Kaase, H. [Technical Univ., Berlin (Germany); Kischkoweit-Lopin, M. [Institut fuer Licht- und Bautechnik an der FH Koln, Cologne (Germany); Scartezzini, J. L.; Michel, L. [Ecole Poytechnuque Federale de Lausanne (Switzerland); Wienold, J.; Apian-Bennewitz, P. [Frauenhofer Institute for Solar Energy Systems, Freiburg (Germany)

    1998-09-01

    The photometric properties of daylighting systems determine the quality of the daylighting in the interior of a building, as well as the possible energy savings by the daylight responsive artificial lighting control systems. Photometric characteristics of daylighting systems and the principles of their measurements in laboratory facilities are described. Characteristics that depend on light incidence and observation of radiation can be measured using integrating sphere photometers or goniophotometers. Luminous transmittance measurements are usually carried out using integrating sphere photometers (cheaper and less time -consuming than measurements with a goniometer). Although the principles involved in the measurement are well understood, results frequently show certain deviations. The various errors that might be responsible for these deviations, whether attributable to the method, or the instrument, or the sample, are also discussed. 10 refs., 8 figs.

  13. Spray ignition measurements in a constant volume combustion vessel under engine-relevant conditions

    Science.gov (United States)

    Ramesh, Varun

    Pressure-based and optical diagnostics for ignition delay (ID) measurement of a diesel spray from a multi-hole nozzle were investigated in a constant volume combustion vessel (CVCV) at conditions similar to those in a conventional diesel engine at the start of injection (SOI). It was first hypothesized that compared to an engine, the shorter ID in a CVCV was caused by NO, a byproduct of premixed combustion. The presence of a significant concentration of NO+NO2 was confirmed experimentally and by using a multi-zone model of premixed combustion. Experiments measuring the effect of NO on ID were performed at conditions relevant to a conventional diesel engine. Depending on the temperature regime and the nature of the fuel, NO addition was found to advance or retard ignition. Constant volume ignition simulations were capable of describing the observed trends; the magnitudes were different due to the physical processes involved in spray ignition, not modeled in the current study. The results of the study showed that ID is sensitive to low NO concentrations (<100 PPM) in the low-temperature regime. A second source of uncertainty in pressure-based ID measurement is the systematic error associated with the correction used to account for the speed of sound. Simultaneous measurements of volumetric OH chemiluminescence (OHC) and pressure during spray ignition found the OHC to closely resemble the pressure-based heat release rate for the full combustion duration. The start of OHC was always found to be shorter than the pressure-based ID for all fuels and conditions tested by 100 ms. Experiments were also conducted measuring the location and timing of high-temperature ignition and the steady-state lift-off length by high-speed imaging of OHC during spray ignition. The delay period calculated using the measured ignition location and the bulk average speed of sound was in agreement with the delay between OHC and the pressure-based ID. Results of the study show that start of OHC

  14. Electromagnetic design of the KATRIN large-volume air coil system

    CERN Document Server

    Glück, Ferenc; Leiber, Benjamin; Mertens, Susanne; Osipowicz, Alexander; Reich, Jan; Wandkowsky, Nancy

    2013-01-01

    The KATRIN experiment is designed to determine the absolute neutrino mass scale with a sensitivity of 200 meV (90 % CL) by measuring the electron energy spectrum close to the endpoint of molecular tritium beta decay. Electrons from a high-intensity gaseous tritium source are guided by a strong magnetic field of a few T to the analyzing plane of the main spectrometer where an integral energy analysis takes place in a low field region (B<0.5 mT). An essential design feature to obtain adiabatic electron transport through this spectrometer is a large volume air coil system surrounding the vessel. The system has two key tasks: to adjust and fine-tune the magnetic guiding field (Low Field Correction System), as well as to compensate the distorting effects of the earth magnetic field (Earth Field Compensation System). In this paper we outline the key electromagnetic design issues for this very large air coil system, which allows for well-defined electron transmission and optimized background reduction in the KATR...

  15. Advanced NSCLC First Pass Perfusion at 64-slice CT: Reproducibility of Volume-based Quantitative Measurement

    Directory of Open Access Journals (Sweden)

    Jie HU

    2010-05-01

    Full Text Available Background and objective The aim of this study is to explore the reproducibility of volume-based quantitative measurement of non-small cell lung cancer (NSCLC perfusion at 64-slice CT. Methods Fourteen patients with proved advanced NSCLC were enrolled in this dynamic first pass volume-based CT perfusion (CTP study (8×5 mm collimation, and they underwent the second scan within 24 h. According to the longest diameters, those patients were classified to ≤3 cm and >3 cm groups, and each group had 7 patients. Intraclass correlation coefficient (ICC and Bland-Altman statistics were used to evaluate the reproducibility of CTP imaging. Results In both groups of advanced NSCLC, the reproducibility with BF, BV, and PS values were good (ICC >0.75 for all, but mean transit time (MTT values. For advanced NSCLC (≤3 cm, repeatability coefficient (RC values with blood flow (BF, blood volume (BV, MTT and permeability surface area product (PS values were 56%, 45%, 114%, and 78%, respectively, and the 95% change intervals of RC were -39%-53%, -29%-62%, -83%-145%, and -57%-98%, respectively. For advanced NSCLC (>3 cm, those values were 46%, 30%, 59%, and 33%, respectively, and the 95% change intervals of RC were -48%-45%, -33%-26%, -54%-64%, and -18%-48%. Conclusion There is greater reproducibility of tumor size >3 cm than that of ≤3 cm. BF and BV could be addressed for reliable clinical application in antiangiogenesis therapeutic monitoring with advanced NSCLC patients.

  16. Regenerative flywheel energy storage system. Volume 1: Executive summary

    Science.gov (United States)

    1980-06-01

    The development, fabrication, and test of a regenerative flywheel energy storage and recovery system for a battery/flywheel electric vehicle of the 3000 pound class are described. The vehicle propulsion system was simulated on a digital computer in order to determine the optimum system operating strategies and to establish a calculated range improvement over a nonregenerative, all electric vehicle. Fabrication of the inductor motor, the flywheel, the power conditioner, and the system control are described. Test results of the system operating over the SAE J227a Schedule D driving cycle are given and are compared to the calculated value. The flywheel energy storage system consists of a solid rotor, synchronous, inductor type, flywheel drive machine electrically coupled to a dc battery electric propulsion system through a load commutated inverter. The motor/alternator unit is coupled mechanically to a small steel flywheel which provides a portion of the vehicle's accelerating energy and regenerates the vehicle's braking energy.

  17. Navigational and Environmental Measurement System (NEMS)

    Science.gov (United States)

    Clem, T. D.

    1988-01-01

    The NEMS concept and design were initiated from the need to measure and record positional and environmental information during aircraft flights of developmental science research instrumentation. The unit was designed as a stand-alone system which could serve the needs of instruments whose developmental nature did not justify the cost and complexity of including these measurements within the instrument data system. Initially, the system was comprised of a Loran-C receiver and a portable IBM compatible computer recording position and time. Later, the system was interfaced with the Wallops aircraft inertial navigation system (INS), and various other sensors were supplied and shared by the Goddard science users. Real-time position mapping on video monitors was added for investigator's use and information. In 1987, the use of a Global Positioning System (GPS) receiver was included in some missions. A total configuration of the system and the various sensors which can be incorporated are shown.

  18. Stabilization system for holographic recording of volume Bragg gratings using a corner cube retroreflector.

    Science.gov (United States)

    Ott, Daniel B; Divliansky, Ivan B; Segall, Marc A; Glebov, Leonid B

    2014-02-20

    Volume Bragg gratings serve an important role in laser development as devices that are able to manipulate both the wavelength and angular spectrum of light. A common method for producing gratings is holographic recording of a two collimated beam interference pattern in a photosensitive material. This process requires stability of the recording system at a level of a fraction of the recording wavelength. A new method for measuring and stabilizing the phase of the recording beams is presented that is extremely flexible and simple to integrate into an existing holographic recording setup and independent of the type of recording media. It is shown that the presented method increases visibility of an interference pattern and for photo-thermo-refractive glass enables enhancement of the spatial refractive index modulation. The use of this technique allows for longer recording times that can lead to the use of expanded recording beams for large aperture gratings.

  19. Dyslexia and voxel-based morphometry: correlations between five behavioural measures of dyslexia and gray and white matter volumes.

    Science.gov (United States)

    Tamboer, Peter; Scholte, H Steven; Vorst, Harrie C M

    2015-10-01

    In voxel-based morphometry studies of dyslexia, the relation between causal theories of dyslexia and gray matter (GM) and white matter (WM) volume alterations is still under debate. Some alterations are consistently reported, but others failed to reach significance. We investigated GM alterations in a large sample of Dutch students (37 dyslexics and 57 non-dyslexics) with two analyses: group differences in local GM and total GM and WM volume and correlations between GM and WM volumes and five behavioural measures. We found no significant group differences after corrections for multiple comparisons although total WM volume was lower in the group of dyslexics when age was partialled out. We presented an overview of uncorrected clusters of voxels (p  200) with reduced or increased GM volume. We found four significant correlations between factors of dyslexia representing various behavioural measures and the clusters found in the first analysis. In the whole sample, a factor related to performances in spelling correlated negatively with GM volume in the left posterior cerebellum. Within the group of dyslexics, a factor related to performances in Dutch-English rhyme words correlated positively with GM volume in the left and right caudate nucleus and negatively with increased total WM volume. Most of our findings were in accordance with previous reports. A relatively new finding was the involvement of the caudate nucleus. We confirmed the multiple cognitive nature of dyslexia and suggested that experience greatly influences anatomical alterations depending on various subtypes of dyslexia, especially in a student sample.

  20. Comparison of vertebral artery velocity and flow volume measurements for diagnosis of vertebrobasilar insufficiency using color duplex sonography

    Energy Technology Data Exchange (ETDEWEB)

    Acar, Murat [Department of Radiology, Faculty of Medicine, Afyon Kocatepe University, Kirmizi Hastane, 03200 Afyon (Turkey)]. E-mail: drmacar@hotmail.com; Degirmenci, Bumin [Department of Radiology, Faculty of Medicine, Afyon Kocatepe University, Kirmizi Hastane, 03200 Afyon (Turkey); Yucel, Aylin [Department of Radiology, Faculty of Medicine, Afyon Kocatepe University, Kirmizi Hastane, 03200 Afyon (Turkey); Albayrak, Ramazan [Department of Radiology, Faculty of Medicine, Afyon Kocatepe University, Kirmizi Hastane, 03200 Afyon (Turkey); Haktanir, Alpay [Department of Radiology, Faculty of Medicine, Afyon Kocatepe University, Kirmizi Hastane, 03200 Afyon (Turkey); Yaman, Mehmet [Department of Neurology, Faculty of Medicine, Afyon Kocatepe University, 03200 Afyon (Turkey)

    2005-05-01

    Introduction: The aim of this study was to compare the measurements of vertebral artery (VA) systolic flow velocity and flow volume for diagnosis of vertebrobasilar insufficiency (VBI). Material and methods: We examined 96 patients who were referred for evaluation of VBI. Net vertebral artery flow volume and mean systolic flow velocity were determined by using color duplex sonography. We had grouped the patients into three according to VA flow volume: group 1 was consisted of patients with severely damped VA flow volume (lower than 120 mL/min), group 2 was consisted of patients with moderately damped VA flow volume (120-200 mL/min), group 3 was consisted of patients with normal VA flow volume (>200 mL/min). The mean systolic flow velocities in each group were compared by one-way ANOVA. Results: Mean VA systolic flow velocities of groups 1, 2 and 3 were 32 {+-} 12, 42 {+-} 10 and 46 {+-} 8 cm/s, respectively. Mean VA systolic flow velocity in group 1 was significantly lower than that of group 2 (P = 0.001). However, there were no significant differences between VA systolic flow velocities in groups 2 and 3 (P = 0.2). Conclusions: According to our findings, measurement of volume in addition to velocity is more valuable in detection of moderately damped VA flow volumes in diagnosis of VBI.

  1. Automatic system for ionization chamber current measurements.

    Science.gov (United States)

    Brancaccio, Franco; Dias, Mauro S; Koskinas, Marina F

    2004-12-01

    The present work describes an automatic system developed for current integration measurements at the Laboratório de Metrologia Nuclear of Instituto de Pesquisas Energéticas e Nucleares. This system includes software (graphic user interface and control) and a module connected to a microcomputer, by means of a commercial data acquisition card. Measurements were performed in order to check the performance and for validating the proposed design.

  2. Calibration Experiments for a Computer Vision Oyster Volume Estimation System

    Science.gov (United States)

    Chang, G. Andy; Kerns, G. Jay; Lee, D. J.; Stanek, Gary L.

    2009-01-01

    Calibration is a technique that is commonly used in science and engineering research that requires calibrating measurement tools for obtaining more accurate measurements. It is an important technique in various industries. In many situations, calibration is an application of linear regression, and is a good topic to be included when explaining and…

  3. Calibration Experiments for a Computer Vision Oyster Volume Estimation System

    Science.gov (United States)

    Chang, G. Andy; Kerns, G. Jay; Lee, D. J.; Stanek, Gary L.

    2009-01-01

    Calibration is a technique that is commonly used in science and engineering research that requires calibrating measurement tools for obtaining more accurate measurements. It is an important technique in various industries. In many situations, calibration is an application of linear regression, and is a good topic to be included when explaining and…

  4. Nuclear proliferation and civilian nuclear power. Report of the Nonproliferation Alternative Systems Assessment Program. Volume VII. International perspectives

    Energy Technology Data Exchange (ETDEWEB)

    1980-06-01

    The purpose of this volume is to assess the proliferation vulnerabilities of the present deployment of civilian nuclear-power systems within the current nonproliferation regime and, in light of their prospective deployment, to consider technical and institutional measures and alternatives which may contribute to an improved regime in which nuclear power could play a significant part. An assessment of these measures must include consideration of their nonproliferation effectiveness as well as their bearing upon energy security, and their operational, economic, and political implications. The nature of these considerations can provide some measure of their likely acceptability to various nations.

  5. Distance and Cable Length Measurement System

    Directory of Open Access Journals (Sweden)

    Jonay Toledo

    2009-12-01

    Full Text Available A simple, economic and successful design for distance and cable length detection is presented. The measurement system is based on the continuous repetition of a pulse that endlessly travels along the distance to be detected. There is a pulse repeater at both ends of the distance or cable to be measured. The endless repetition of the pulse generates a frequency that varies almost inversely with the distance to be measured. The resolution and distance or cable length range could be adjusted by varying the repetition time delay introduced at both ends and the measurement time. With this design a distance can be measured with centimeter resolution using electronic system with microsecond resolution, simplifying classical time of flight designs which require electronics with picosecond resolution. This design was also applied to position measurement.

  6. Distance and Cable Length Measurement System

    Science.gov (United States)

    Hernández, Sergio Elias; Acosta, Leopoldo; Toledo, Jonay

    2009-01-01

    A simple, economic and successful design for distance and cable length detection is presented. The measurement system is based on the continuous repetition of a pulse that endlessly travels along the distance to be detected. There is a pulse repeater at both ends of the distance or cable to be measured. The endless repetition of the pulse generates a frequency that varies almost inversely with the distance to be measured. The resolution and distance or cable length range could be adjusted by varying the repetition time delay introduced at both ends and the measurement time. With this design a distance can be measured with centimeter resolution using electronic system with microsecond resolution, simplifying classical time of flight designs which require electronics with picosecond resolution. This design was also applied to position measurement. PMID:22303169

  7. Measuring the orthogonality error of coil systems

    Science.gov (United States)

    Heilig, B.; Csontos, A.; Pajunpää, K.; White, Tim; St. Louis, B.; Calp, D.

    2012-01-01

    Recently, a simple method was proposed for the determination of pitch angle between two coil axes by means of a total field magnetometer. The method is applicable when the homogeneous volume in the centre of the coil system is large enough to accommodate the total field sensor. Orthogonality of calibration coil systems used for calibrating vector magnetometers can be attained by this procedure. In addition, the method can be easily automated and applied to the calibration of delta inclination–delta declination (dIdD) magnetometers. The method was tested by several independent research groups, having a variety of test equipment, and located at differing geomagnetic observatories, including: Nurmijärvi, Finland; Hermanus, South Africa; Ottawa, Canada; Tihany, Hungary. This paper summarizes the test results, and discusses the advantages and limitations of the method.

  8. SPEED ROLLER STAND MEASUREMENT SYSTEM CHECKING TECHNIQUE

    OpenAIRE

    Zybtsev, Y.; I. Marmut

    2011-01-01

    The study has shown that the accuracy of brakes checking by inertial stands depends upon the applied methods of measurement of braking parameters (stand slowing down, braking distance, brakes triggering time, current speed) as well as the methods of metrological checking of measuring system canals.

  9. Assessment of effectiveness of geologic isolation systems. CIRMIS data system. Volume 3. Generator routines

    Energy Technology Data Exchange (ETDEWEB)

    Friedrichs, D.R.; Argo, R.S.

    1980-01-01

    The Assessment of Effectiveness of Geologic Isolation Systems (AEGIS) Program is developing and applying the methodology for assessing the far-field, long-term post-closure safety of deep geologic nuclear waste repositories. AEGIS is being performed by Pacific Northwest Laboratory (PNL) under contract with the Office of Nuclear Waste Isolation (ONWI) for the Department of Energy (DOE). One task within AEGIS is the development of methodology for analysis of the consequences (water pathway) from loss of repository containment as defined by various release scenarios. The various input parameters required in the analysis are compiled in data systems. The data are organized and prepared by various input subroutines for utilization by the hydraulic and transport codes. The hydrologic models simulate the groundwater flow systems and provide water flow directions, rates, and velocities as inputs to the transport models. Outputs from the transport models are basically graphs of radionuclide concentration in the groundwater plotted against time. After dilution in the receiving surface-water body (e.g., lake, river, bay), these data are the input source terms for the dose models, if dose assessments are required. The dose models calculate radiation dose to individuals and populations. CIRMIS (Comprehensive Information Retrieval and Model Input Sequence) Data System, a storage and retrieval system for model input and output data, including graphical interpretation and display is described. This is the third of four volumes of the description of the CIRMIS Data System.

  10. System for measuring electric resistance skin

    Directory of Open Access Journals (Sweden)

    V. P. Kutsenko

    2015-09-01

    Full Text Available Introduction. To measure the electrical resistance of leather frequently used system for applying testing signals from external current sources or voltage. Power testing signals the maximum limit, when they Electro studies still have a negative impact on the human body. Formulation of the problem. To achieve this task the authors conducted research and developed a system, which is based to measure electrical skin resistance (ESR responsible allocation and measurement noise variance bioelectric signal is proportional to the resistance area of research. Main body. The paper studied and developed a system, based on measuring electrical skin resistance on the identification and measurement of the noise variance from the BAP bioelectric signal that is proportional to the resistance of the investigation. A functional block diagram of an automated algorithm for converting the useful and noise signal BAP, whose range does not differ fundamentally from those of the intrinsic noise of the input elements in ESR. The proposed method will improve the accuracy of the measurements ESR without the use of test pacing signal. The simulation results and experimental studies correlate that confirms the adequacy of this method the results of experimental measurements. Conclusions. For noise voltage BAT can measure their electrical resistance without signals tested, external sources of electric current or voltage and thereby completely eliminate the harmful effect of probing. Thanks to one of the Inverting periodic noise voltages multiplied and simultaneous detection variable component switching frequency, provided the allocation and measurement noise voltage acupuncture points, which is proportional to the resistance, and the intensity of the same order or less than the intrinsic noise of the measuring system. Use as medical acupuncture needle electrodes allows to measure not only the skin but also deep resistivity, which reflects the physiological state of internal

  11. Prognostic value of epicardial fat volume measurements by computed tomography: a systematic review of the literature

    Energy Technology Data Exchange (ETDEWEB)

    Spearman, James V.; Krazinski, Aleksander W. [Medical University of South Carolina, Department of Radiology and Radiological Science, Charleston, SC (United States); Renker, Matthias [Medical University of South Carolina, Department of Radiology and Radiological Science, Charleston, SC (United States); Giessen University, Department of Internal Medicine I, Cardiology/Angiology, Giessen (Germany); Schoepf, U.J. [Medical University of South Carolina, Department of Radiology and Radiological Science, Charleston, SC (United States); Medical University of South Carolina, Division of Cardiology, Department of Medicine, Charleston, SC (United States); Herbert, Teri L. [Medical University of South Carolina, Department of Library Science and Informatics, Charleston, SC (United States); De Cecco, Carlo N. [Medical University of South Carolina, Department of Radiology and Radiological Science, Charleston, SC (United States); University of Rome ' Sapienza' - Polo Pontino, Department of Radiological Sciences, Oncology and Pathology, Latina (Italy); Nietert, Paul J. [Medical University of South Carolina, Department of Public Health Sciences, Charleston, SC (United States); Meinel, Felix G. [Medical University of South Carolina, Department of Radiology and Radiological Science, Charleston, SC (United States); Ludwig-Maximilians-University Hospital, Institute for Clinical Radiology, Munich (Germany)

    2015-11-15

    To perform a systematic review of the growing body of literature evaluating the prognostic value of epicardial fat volume (EFV) quantified by cross-sectional imaging. Two independent reviewers performed systematic searches on both PubMed and Scopus using search terms developed with a medical librarian. Peer-reviewed articles were selected based on the inclusion of outcome data, utilization of epicardial fat volume and sufficient reporting for analysis. A total of 411 studies were evaluated with nine studies meeting the inclusion criteria. In all, the studies evaluated 10,252 patients. All nine studies were based on CT measurements. Seven studies evaluated the prognostic value of EFV unadjusted for calcium score, and six of these studies found a significant association between EFV and clinical outcomes. Seven studies evaluated the incremental value of EFV beyond calcium scoring, and six of these studies found a significant association. The majority of studies suggest that EFV quantification is significantly associated with clinical outcomes and provides incremental prognostic value over coronary artery calcium scoring. Future research should use a binary cutoff of 125 mL for evaluation of EFV to provide consistency with other research. (orig.)

  12. Intelligent systems: A semiotic perspective. Volume I: Theoretical semiotics

    Energy Technology Data Exchange (ETDEWEB)

    Albus, J.; Meystel, A.; Quintero, R.

    1996-12-31

    This report contains the papers from the Proceedings of the 1996 International Multidisciplinary Conference - Theoretical Semiotics. General topics covered are: semiotic in biology: biologically inspired complex systems; intelligence in constructed complex systems; intelligence of learning and evolution; fuzzy logic and the mechanisms of generalization; information representation for decision making; sematic foundations; syntactics of intelligent systems: the kind of logic available; intelligence of recognition: the semiotic tools; and multiresolutional methods.

  13. Quantitative measurements of cerebral blood flow in volume imaging PET scanners

    Energy Technology Data Exchange (ETDEWEB)

    Smith, R.J.; Shao, L.; Freifelder, R.; Karp, J.S.; Ragland, J.D. [Univ. of Pennsylvania, Philadelphia, PA (United States)

    1995-08-01

    Quantitative measurements of Cerebral Blood Flow (CBF) are performed in a volume imaging PET Scanner by means of moderate activity infusions. In equilibrium infusions, activations are measured by scanning over 10 minutes with 16 minute activations. Typical measured whole brain CBF values are 37{+-}8 ml/min/100g, close to the value of 42 ml/min/100g reported by other groups using this method. For ramped infusions, scanning over 4 minutes with 5 minute activations results in whole brain CBFs of 49 {+-} 9 ml/min/100g, close to the Kety and Schmidt value of 50 ml/min/100g. Both equilibrium and ramped infusion methods have been used to study face and word memory in human subjects. Both methods were able to detect significant activations in regions implicated in human memory. The authors conclude that precise quantitation of regional CBF is achieved using both methods, and that ramped infusions also provide accurate measures of CBF. In addition a simplified protocol for ramped infusion studies has been developed. In this method the whole brain tissue time activity curve generated from dynamic scanning is replaced by an appropriately scaled camera coincidence countrate curve. The resulting whole brain CBF values are only 7% different from the dynamic scan and fit results. Regional CBFs (rCBF) may then be generated from the summed image (4.25 minutes) using a count density vs flow lookup table.

  14. Tumor-to-breast volume ratio as measured on MRI: a possible predictor of breast-conserving surgery versus mastectomy.

    Science.gov (United States)

    Faermann, Renata; Sperber, Fani; Schneebaum, Schlomo; Barsuk, Daphna

    2014-02-01

    The surgical approach to breast cancer changed dramatically in the past 20 years. The surgical objective today is to remove the tumor, ensuring negative margins and good cosmetic results, and preserving the breast when possible. Magnetic resonance imaging of the breast has become an essential imaging tool prior to surgery, diagnosing additional tumors and assessing tumor extent. Tumor-to-breast volume ratio, an important predictor of breast conservation, can be measured with MRI and may change the surgical decision. To measure the tumor-to-breast volume ratio using MRI in order to assess whether there is a correlation between this ratio and the type of surgery selected (breast-conserving or mastectomy). The volumes of the tumor and the breast and the tumor-to-breast volume ratio were retrospectively calculated using preoperative breast MRI in 76 patients who underwent breast-conserving surgery or mastectomy. Breast-conserving surgery (lumpectomy) was performed in 64 patients and mastectomy in 12. The average tumor-to-breast volume ratio was 0.06 (6%) in the lumpectomy group and 0.30 (30%) in the mastectomy group (P < 0.0001). The tumor-to-breast volume ratio correlated with the type of surgery. As measured on MRI, this ratio is an accurate means of determining the type of surgery best suited for a given patient. It is recommended that MRI-determined tumor-to-breast volume ratio become part of the surgical planning protocol for patients diagnosed with breast cancer.

  15. MEASURED DENSITIES, REFRACTIVE INDICES, EXCESS MOLAR VOLUMES AND DEVIATIONS CALCULATED FROM MOLAR REFRACTION OF THE BINARY MIXTURE OF ETHANOL + 1-NONANOL AND TERNARY MIXTURE ETHANOL + 1-NONANOL + WATER AT 293.15 K

    Directory of Open Access Journals (Sweden)

    Mehmet MAHRAMANLIOĞLU

    2000-03-01

    Full Text Available Densities, and refractive indices were measured for the binary system ethanol + 1-nonanol and ternary system ethanol + 1-nonanol + water at 293.15 K. The excess molar volumes, and the deviations molar refraction were calculated for binary and ternary system. Redlich-Kister type equation was fitted to the excess molar volumes and, the deviations from a mole fraction average of the molar refraction, and the values of coefficients were calculated

  16. Comparison of volume and diameter measurement in assessing small abdominal aortic aneurysm expansion examined using computed tomographic angiography

    Energy Technology Data Exchange (ETDEWEB)

    Parr, Adam; Jayaratne, Chanaka; Buttner, Petra [Vascular Biology Unit, James Cook University, Townsville, Queensland 4811 (Australia); Golledge, Jonathan, E-mail: Jonathan.Golledge@jcu.edu.au [Vascular Biology Unit, James Cook University, Townsville, Queensland 4811 (Australia)

    2011-07-15

    Aim: First we aimed to assess the reproducibility of a computer tomography angiography (CTA) based technique for measuring infra-renal aortic volume and diameter. Second we sought to investigate whether changes in aortic volume and diameter were similar during follow-up. Materials and methods: A prospective series of 57 patients, with aortic diameter initially measuring between 25 and 55 mm, were assessed with 2 CTAs a median of 14 months apart. Aortic volume and maximum diameter (both axial and orthogonal) were measured by a semi-automated workstation protocol based on previously defined techniques. Intra- and inter-observer reproducibility were assessed by repeat assessment of the initial CTA images of the first 33 patients included in the study, in order to estimate the 95% limits of agreements. Changes in aortic dimensions between the first and follow-up CTA, were defined for volume and diameter separately as changes greater than their respective 95% limits of agreement. Results: Reproducibility of aortic volume and diameter was excellent with an average coefficient of variation <4%. The median (inter-quartile range) increases in total volume, orthogonal and axial diameters were 4.9 cm{sup 3} (0.01-14.18), 1.2 mm (0.40-3.50) and 1.4 mm (-0.15 to 3.55) respectively. Forty-two percent of patients who had increased aortic volume above the 95% limit of agreement did not display corresponding axial or orthogonal diameter changes. Conclusions: Infra-renal total aortic volume, axial and orthogonal diameter can all be measured reproducibly from CTA. Aortic volume changes are not always reflected by similar changes in diameter and therefore provide complementary information when assessing AAA expansion over time.

  17. Time measurment system at the SSC

    Energy Technology Data Exchange (ETDEWEB)

    Arai, Yasuo [National Laboratory for High Energy Physics, Ibaraki (Japan)

    1989-04-01

    A proposal of time measurement system at the SSC experiment is described. An example of a possible scheme for central tracking chambers is shown. Designs of a preamp/shaper/discri chip and a time digitizer chip are described. A method to distribute system clock and power/cooling problems are also discussed.

  18. Natural Resource Information System. Volume I. Overall Description.

    Science.gov (United States)

    Boeing Computer Services, Inc., Seattle, WA.

    Recognizing the need for the development of a computer based information system which would handle remote sensing as well as conventional mapping data, the Bureau of Indian Affairs and the Bureau of Land Management contracted with Boeing Computer Services for the design and construction of a prototype Natural Resource Information System. The…

  19. Expert Systems on Multiprocessor Architectures. Volume 3. Technical Reports

    Science.gov (United States)

    1991-06-01

    nodes, in which they are interested, eliminating all knowledge search. In conventional blackb -oard systems, knowledge sources are units of scheduling...data can therefore be implemented in a distributed manner. " Most blackb ’:trd systems represent the properties of an object simply as lists of values

  20. Variable volume combustor with nested fuel manifold system

    Energy Technology Data Exchange (ETDEWEB)

    McConnaughhay, Johnie Franklin; Keener, Christopher Paul; Johnson, Thomas Edward; Ostebee, Heath Michael

    2016-09-13

    The present application provides a combustor for use with a gas turbine engine. The combustor may include a number of micro-mixer fuel nozzles, a fuel manifold system in communication with the micro-mixer fuel nozzles to deliver a flow of fuel thereto, and a linear actuator to maneuver the micro-mixer fuel nozzles and the fuel manifold system.

  1. Variable volume combustor with pre-nozzle fuel injection system

    Energy Technology Data Exchange (ETDEWEB)

    Keener, Christopher Paul; Johnson, Thomas Edward; McConnaughhay, Johnie Franklin; Ostebee, Heath Michael

    2016-09-06

    The present application provides a combustor for use with a gas turbine engine. The combustor may include a number of fuel nozzles, a pre-nozzle fuel injection system supporting the fuel nozzles, and a linear actuator to maneuver the fuel nozzles and the pre-nozzle fuel injection system.

  2. Internal Performance Measurement Systems: Problems and Solutions

    DEFF Research Database (Denmark)

    Jakobsen, Morten; Mitchell, Falconer; Nørreklit, Hanne

    2010-01-01

    . The analysis uses and extends N rreklit's (2000) critique of the BSC by applying the concepts developed therein to contemporary research on the BSC and to the development of practice in performance measurement. The analysis is of relevance for many companies in the Asia-Pacific area as an increasing numbers......This article pursues two aims: to identify problems and dangers related to the operational use of internal performance measurement systems of the Balanced Scorecard (BSC) type and to provide some guidance on how performance measurement systems may be designed to overcome these problems...

  3. Preliminary characterization of abandoned septic tank systems. Volume 1

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-12-01

    This report documents the activities and findings of the Phase I Preliminary Characterization of Abandoned Septic Tank Systems. The purpose of the preliminary characterization activity was to investigate the Tiger Team abandoned septic systems (tanks and associated leachfields) for the purpose of identifying waste streams for closure at a later date. The work performed was not to fully characterize or remediate the sites. The abandoned systems potentially received wastes or effluent from buildings which could have discharged non-domestic, petroleum hydrocarbons, hazardous, radioactive and/or mixed wastes. A total of 20 sites were investigated for the preliminary characterization of identified abandoned septic systems. Of the 20 sites, 19 were located and characterized through samples collected from each tank(s) and, where applicable, associated leachfields. The abandoned septic tank systems are located in Areas 5, 12, 15, 25, and 26 on the Nevada Test Site.

  4. Information system life-cycle and documentation standards, volume 1

    Science.gov (United States)

    Callender, E. David; Steinbacher, Jody

    1989-01-01

    The Software Management and Assurance Program (SMAP) Information System Life-Cycle and Documentation Standards Document describes the Version 4 standard information system life-cycle in terms of processes, products, and reviews. The description of the products includes detailed documentation standards. The standards in this document set can be applied to the life-cycle, i.e., to each phase in the system's development, and to the documentation of all NASA information systems. This provides consistency across the agency as well as visibility into the completeness of the information recorded. An information system is software-intensive, but consists of any combination of software, hardware, and operational procedures required to process, store, or transmit data. This document defines a standard life-cycle model and content for associated documentation.

  5. Reactor safeguards system assessment and design. Volume I

    Energy Technology Data Exchange (ETDEWEB)

    Varnado, G.B.; Ericson, D.M. Jr.; Daniel, S.L.; Bennett, H.A.; Hulme, B.L.

    1978-06-01

    This report describes the development and application of a methodology for evaluating the effectiveness of nuclear power reactor safeguards systems. Analytic techniques are used to identify the sabotage acts which could lead to release of radioactive material from a nuclear power plant, to determine the areas of a plant which must be protected to assure that significant release does not occur, to model the physical plant layout, and to evaluate the effectiveness of various safeguards systems. The methodology was used to identify those aspects of reactor safeguards systems which have the greatest effect on overall system performance and which, therefore, should be emphasized in the licensing process. With further refinements, the methodology can be used by the licensing reviewer to aid in assessing proposed or existing safeguards systems.

  6. Measurement of oil volume fraction and velocity distributions in vertical oil-in-water flows using ERT and a local probe

    Institute of Scientific and Technical Information of China (English)

    LI Hua; WANG Mi; WU Ying-xiang; MA Yi-xin; WILLIAMS Richard

    2005-01-01

    This paper presents the use of a high performance dual-plane electrical resistance tomography (ERT) system and a local dual-sensor conductance probe to measure the vertical upward oil-in-water pipe flows in which the mean oil volume fraction is up to 23.1%.A sensitivity coefficient back-projection (SBP) algorithm was adopted to reconstruct the flow distributions and a cross correlation method was applied to obtain the oil velocity distributions. The oil volume fraction and velocity distributions obtained from both measurement techniques were compared and good agreement was found, which indicates that the ERT technique can be used to measure the low fraction oil-water flows. Finally, the factors affecting measurement precision were discussed.

  7. Testing and Evaluating C3I Systems That Employ AI. Volume 1. Handbook for Testing Expert Systems

    Science.gov (United States)

    1991-01-31

    implements the multiattribute utility analysis ( MAUA ) framework for testing and evaluating expert systems described in Volume 1. Volume 1 is intended as...our methods may wish to skim Chapter 7, "Pulling It All Together," first. He or she may then wish to review the attributes in the MAUA hierarchy...presented in the latter half of Chapter 3, "Proposed MAUA Framework for Testing and Evaluating Expert Systems." A detailed example of the method is given

  8. Measuring Vulnerability in the Food System

    OpenAIRE

    Paloviita, Ari; Puupponen, Antti; Kortetmäki, Teea; Silvasti, Tiina

    2015-01-01

    Food system vulnerability is an emerging concept for food security policies and food supply chain management. Hence, measuring food system vulnerability is necessary for developing appropriate food security policies and managing food supply chain vulnerabilities. In this paper, we aim to clarify the development process of food system vulnerability indicators. We conducted an abducted qualitative content analysis based on public documents of various Finnish organizations, including mi...

  9. Volatility Measurements Applied to Information Systems

    Science.gov (United States)

    2013-09-01

    LISI Levels of Information Systems Integration NPV Net Present Value OEP Organizational Execution Plans ROI Return on Investment SIGINT Signals...IT system (Stikeleather, 2013). The interoperability performance can be measured with the Levels of Information Systems Interoperability ( LISI ), which...support (DoD CIO, 2012). There are several IT evaluation methods including net present value (NPV), ROI, information economics, cost benefit analysis, and

  10. NKS MOMS. Final report. [Mobile Measurement Systems

    Energy Technology Data Exchange (ETDEWEB)

    Nilssen, J. [Norwegian Radiation Protection Authority (NRPA) (Norway); Aage, H.K. [Danish Emergency Management Agency (DEMA) (Denmark); Palsson, S.E. [Icelandic Radiation Safety Authority (IRSA) (Iceland)

    2013-02-15

    Mobile car-borne measurement systems are an important asset in early phase emergency response in all Nordic countries. However, through the development of the systems in the different countries, there are considerable differences between the systems developed. This complicates Nordic cooperation and mutual assistance in emergency situations. This project aimed to facilitate harmonization of mobile measurement systems between the Nordic countries. The project focused on harmonizing data formats, information exchange and measurement strategies. Although the work done was funded by each member, the project established a good platform for cooperation which will hopefully continue beyond the scope of the project. A two-day seminar was held in May 2012, where all participants presented the current status (equipment, methods used etc.), in addition to invited speakers presenting development within the field of mobile detection and in situ measurements. Exchange of experiences and information on different measurement systems and practises in use was an important part of the seminar. The seminar was followed up by a small workshop during the REFOX exercise in Lund, Sweden, September 2012. Exchange of measurement data from the exercise was facilitated through a workspace proveded by NRPA as part of the MOMS project. The work done in this project will be presented at the NordEx12 seminar in March 2013. (Author)

  11. Gas permeation measurement under defined humidity via constant volume/variable pressure method

    KAUST Repository

    Jan Roman, Pauls

    2012-02-01

    Many industrial gas separations in which membrane processes are feasible entail high water vapour contents, as in CO 2-separation from flue gas in carbon capture and storage (CCS), or in biogas/natural gas processing. Studying the effect of water vapour on gas permeability through polymeric membranes is essential for materials design and optimization of these membrane applications. In particular, for amine-based CO 2 selective facilitated transport membranes, water vapour is necessary for carrier-complex formation (Matsuyama et al., 1996; Deng and Hägg, 2010; Liu et al., 2008; Shishatskiy et al., 2010) [1-4]. But also conventional polymeric membrane materials can vary their permeation behaviour due to water-induced swelling (Potreck, 2009) [5]. Here we describe a simple approach to gas permeability measurement in the presence of water vapour, in the form of a modified constant volume/variable pressure method (pressure increase method). © 2011 Elsevier B.V.

  12. Systems and methods for measuring component matching

    Science.gov (United States)

    Courter, Kelly J. (Inventor); Slenk, Joel E. (Inventor)

    2006-01-01

    Systems and methods for measuring a contour match between adjacent components are disclosed. In one embodiment, at least two pressure sensors are located between adjacent components. Each pressure sensor is adapted to obtain a pressure measurement at a location a predetermined distance away from the other pressure sensors, and to output a pressure measurement for each sensor location. An output device is adapted to receive the pressure measurements from at least two pressure sensors and display the pressure measurements. In one aspect, the pressure sensors include flexible thin film pressure sensors. In accordance with other aspects of the invention, a method is provided for measuring a contour match between two interfacing components including measuring at least one pressure applied to at least one sensor between the interfacing components.

  13. First common volume measurements of PMSE and NLC layers above EISCAT, Tromsö

    Science.gov (United States)

    Dalin, Peter; Mann, Ingrid; Häggström, Ingemar

    2016-04-01

    Close to the mesopause in the atmosphere at medium to high latitudes ice particles form during the summer months. The ice particles are observed in noctilucent clouds (NLC) and cause the formation of specific radar echoes, Polar Mesospheric Summer Echoes (PMSE). While NLC and PMSE are both linked to the presence of ice particles and observed at similar overlapping altitudes, they are also influenced by other parameters, e.g. neutral atmospheric dynamics, turbulence and dusty plasma effects, and their exact formation conditions are still subject to investigations. We here present first results from a number of simultaneous observations of both phenomena. The "Mesoclouds" campaign was conducted between 8-20 August 2015 with the aim to investigate PMSE and NLC activity in the common volume of the atmosphere above the Tromsö EISCAT station. For simultaneous optical and radar measurements of NLC and PMSE layers we ran EISCAT VHF (224 MHz) and UHF (930 MHz) radars at Tromsö (Norway) as well as two optical NLC cameras located at Kiruna and Nikkaluokta (Sweden). Both locations of the NLC cameras are about 200 km south of Tromsö, which permits making NLC triangulation measurements. Three NLC/PMSE cases above Tromsö are discussed. The first case on 9-10 August displayed NLC and PMSE layers simultaneously above Tromsö. The second case on 12-13 August showed a partial coincidence of NLC and PMSE: NLC were observed in the evening and morning hours whereas PMSE were mostly seen in the morning hours. In the third case on 19-20 August no NLC were observed, while PMSE were observed in the morning hours. We present the observational data, investigate peculiar dynamical features intrinsic to PMSE and NLC layers in the common atmospheric volume and discuss its implications for observation of ice particles.

  14. Telerobotic system performance measurement: motivation and methods

    Science.gov (United States)

    Kondraske, George V.; Khoury, George J.

    1992-11-01

    Telerobotic systems (TRSs) and shared teleautonomous systems result from the integration of multiple sophisticated modules. Procedures used in systems integration design decision-making of such systems are frequently ad hoc compared to more quantitative and systematic methods employed elsewhere in engineering. Experimental findings associated with verification and validation (V&V) are often application-specific. Furthermore, models and measurement strategies do not exist which allow prediction of overall TRS performance in a given task based on knowledge of the performance characteristics of individual subsystems. This paper introduces the use of general systems performance theory (GSPT), developed by the senior author to help resolve similar problems in human performance, as a basis for: (1) measurement of overall TRS performance (viewing all system components, including the operator, as a single entity); (2) task decomposition; (3) development of a generic TRS model; and (4) the characterization of performance of subsystems comprising the generic model. GSPT uses a resource construct to model performance and resource economic principles to govern the interface of systems to tasks. It provides a comprehensive modeling/measurement strategy applicable to complex systems including both human and artificial components. Application is presented in the context of a distributed telerobotics network (Universities Space Automation and Robotics Consortium) as a testbed. Insight into the design of test protocols which elicit application-independent data (i.e., multi-purpose or reusable) is described. Although the work is motivated by space automation and robotics challenges, it is considered to be applicable to telerobotic systems in general.

  15. Foot Plantar Pressure Measurement System: A Review

    Directory of Open Access Journals (Sweden)

    Yufridin Wahab

    2012-07-01

    Full Text Available Foot plantar pressure is the pressure field that acts between the foot and the support surface during everyday locomotor activities. Information derived from such pressure measures is important in gait and posture research for diagnosing lower limb problems, footwear design, sport biomechanics, injury prevention and other applications. This paper reviews foot plantar sensors characteristics as reported in the literature in addition to foot plantar pressure measurement systems applied to a variety of research problems. Strengths and limitations of current systems are discussed and a wireless foot plantar pressure system is proposed suitable for measuring high pressure distributions under the foot with high accuracy and reliability. The novel system is based on highly linear pressure sensors with no hysteresis.

  16. Linear systems a measurement based approach

    CERN Document Server

    Bhattacharyya, S P; Mohsenizadeh, D N

    2014-01-01

    This brief presents recent results obtained on the analysis, synthesis and design of systems described by linear equations. It is well known that linear equations arise in most branches of science and engineering as well as social, biological and economic systems. The novelty of this approach is that no models of the system are assumed to be available, nor are they required. Instead, a few measurements made on the system can be processed strategically to directly extract design values that meet specifications without constructing a model of the system, implicitly or explicitly. These new concepts are illustrated by applying them to linear DC and AC circuits, mechanical, civil and hydraulic systems, signal flow block diagrams and control systems. These applications are preliminary and suggest many open problems. The results presented in this brief are the latest effort in this direction and the authors hope these will lead to attractive alternatives to model-based design of engineering and other systems.

  17. Thermoelectric property measurements with computer controlled systems

    Science.gov (United States)

    Chmielewski, A. B.; Wood, C.

    1984-01-01

    A joint JPL-NASA program to develop an automated system to measure the thermoelectric properties of newly developed materials is described. Consideration is given to the difficulties created by signal drift in measurements of Hall voltage and the Large Delta T Seebeck coefficient. The benefits of a computerized system were examined with respect to error reduction and time savings for human operators. It is shown that the time required to measure Hall voltage can be reduced by a factor of 10 when a computer is used to fit a curve to the ratio of the measured signal and its standard deviation. The accuracy of measurements of the Large Delta T Seebeck coefficient and thermal diffusivity was also enhanced by the use of computers.

  18. A Critique of Health System Performance Measurement.

    Science.gov (United States)

    Lynch, Thomas

    2015-01-01

    Health system performance measurement is a ubiquitous phenomenon. Many authors have identified multiple methodological and substantive problems with performance measurement practices. Despite the validity of these criticisms and their cross-national character, the practice of health system performance measurement persists. Theodore Marmor suggests that performance measurement invokes an "incantatory response" wrapped within "linguistic muddle." In this article, I expand upon Marmor's insights using Pierre Bourdieu's theoretical framework to suggest that, far from an aberration, the "linguistic muddle" identified by Marmor is an indicator of a broad struggle about the representation and classification of public health services as a public good. I present a case study of performance measurement from Alberta, Canada, examining how this representational struggle occurs and what the stakes are.

  19. Peripheral arterial volume distensibility: significant differences with age and blood pressure measured using an applied external pressure.

    Science.gov (United States)

    Zheng, Dingchang; Murray, Alan

    2011-05-01

    A new arterial distensibility measurement technique was assessed in 100 healthy normotensive subjects. Arterial transmural pressures on the whole right arm were reduced with a 50 cm long cuff inflated to 10, 20, 30 and 40 mmHg. The electrocardiogram, and finger and ear photoplethysmograms were recorded simultaneously. Arm pulse propagation time, pulse wave velocity (PWV) and arterial volume distensibility were determined. With a 40 mmHg reduction in transmural pressure, arm pulse propagation time increased from 61 to 83 ms, PWV decreased from 12 to 8 m s(-1) and arterial distensibility increased from 0.102% to 0.232% per mmHg (all P pressures, arterial distensibility was significantly related to resting mean arterial pressure (MAP), diastolic blood pressure (DBP) and age, and for systolic blood pressure at 30 and 40 mmHg (all P pressure, arterial distensibility fell by 54% for a MAP increase from 75 to 105 mmHg, 57% for a DBP increase from 60 to 90 mmHg and 47% for an age increase from 20 to 70 years. These changes were more than double than those without cuff pressure. Our technique showed that systemic volume distensibility of the peripheral arm artery reduced with age, with a greater effect at higher external and lower transmural pressures.

  20. Integration of optical measurement methods with flight parameter measurement systems

    Science.gov (United States)

    Kopecki, Grzegorz; Rzucidlo, Pawel

    2016-05-01

    During the AIM (advanced in-flight measurement techniques) and AIM2 projects, innovative modern techniques were developed. The purpose of the AIM project was to develop optical measurement techniques dedicated for flight tests. Such methods give information about aircraft elements deformation, thermal loads or pressure distribution, etc. In AIM2 the development of optical methods for flight testing was continued. In particular, this project aimed at the development of methods that could be easily applied in flight tests in an industrial setting. Another equally important task was to guarantee the synchronization of the classical measuring system with cameras. The PW-6U glider used in flight tests was provided by the Rzeszów University of Technology. The glider had all the equipment necessary for testing the IPCT (image pattern correlation technique) and IRT (infrared thermometry) methods. Additionally, equipment adequate for the measurement of typical flight parameters, registration and analysis has been developed. This article describes the designed system, as well as presenting the system’s application during flight tests. Additionally, the results obtained in flight tests show certain limitations of the IRT method as applied.