WorldWideScience

Sample records for voltage standing wave

  1. A Novel High-Frequency Voltage Standing-Wave Ratio-Based Grounding Electrode Line Fault Supervision in Ultra-High Voltage DC Transmission Systems

    Directory of Open Access Journals (Sweden)

    Yufei Teng

    2017-03-01

    Full Text Available In order to improve the fault monitoring performance of grounding electrode lines in ultra-high voltage DC (UHVDC transmission systems, a novel fault monitoring approach based on the high-frequency voltage standing-wave ratio (VSWR is proposed in this paper. The VSWR is defined considering a lossless transmission line, and the characteristics of the VSWR under different conditions are analyzed. It is shown that the VSWR equals 1 when the terminal resistance completely matches the characteristic impedance of the line, and when a short circuit fault occurs on the grounding electrode line, the VSWR will be greater than 1. The VSWR will approach positive infinity under metallic earth fault conditions, whereas the VSWR in non-metallic earth faults will be smaller. Based on these analytical results, a fault supervision criterion is formulated. The effectiveness of the proposed VSWR-based fault supervision technique is verified with a typical UHVDC project established in Power Systems Computer Aided Design/Electromagnetic Transients including DC(PSCAD/EMTDC. Simulation results indicate that the proposed strategy can reliably identify the grounding electrode line fault and has strong anti-fault resistance capability.

  2. Residual Liquefaction under Standing Waves

    DEFF Research Database (Denmark)

    Kirca, V.S. Ozgur; Sumer, B. Mutlu; Fredsøe, Jørgen

    2012-01-01

    This paper summarizes the results of an experimental study which deals with the residual liquefaction of seabed under standing waves. It is shown that the seabed liquefaction under standing waves, although qualitatively similar, exhibits features different from that caused by progressive waves....... The experimental results show that the buildup of pore-water pressure and the resulting liquefaction first starts at the nodal section and spreads towards the antinodal section. The number of waves to cause liquefaction at the nodal section appears to be equal to that experienced in progressive waves for the same...... wave height. Recommendations are made as to how to assess liquefaction potential in standing waves. Copyright © 2012 by the International Society of Offshore and Polar Engineers (ISOPE)....

  3. Students dance longitudinal standing waves

    Science.gov (United States)

    Ruiz, Michael J.

    2017-05-01

    A demonstration is presented that involves students dancing longitudinal standing waves. The resulting kinaesthetic experience and visualization both contribute towards an understanding of the natural modes of vibrations in open and closed pipes. A video of this fun classroom activity is provided (http://mjtruiz.com/ped/dance/).

  4. The nonlinear standing wave inside the space of liquid

    Institute of Scientific and Technical Information of China (English)

    2010-01-01

    Based on the basic equations of hydrodynamics, the nonlinear acoustic wave equation is obtained. By taking into account the boundary condition and properties of nonlinear standing wave, the equation is solved through perturbation method, and the stable expressions of fundamental wave and second harmonic are presented. The sound pressures in an ultrasonic cleaner are measured by hydrophones, and the relationship between the received voltages of hydrophones and the output voltages of the ultrasonic generator is researched. The study shows the existence of the nonlinear effect of liquid and analyzes the frequency spectrum of the received signals by hydrophones, by which the fundamental wave, second and high order harmonics are found coexisting in the bounded space filled with liquids. The theory and experimental results testify the existence of the nonlinear standing wave in liquid. Owing to the restricted applicability of perturbation method, the theoretical results of the fundamental wave and second harmonic are good only for the weak nonlinear phenomenon.

  5. Gravity Capillary Standing Water Waves

    Science.gov (United States)

    Alazard, Thomas; Baldi, Pietro

    2015-09-01

    The paper deals with the 2D gravity-capillary water waves equations in their Hamiltonian formulation, addressing the question of the nonlinear interaction of a plane wave with its reflection off a vertical wall. The main result is the construction of small amplitude, standing (namely periodic in time and space, and not travelling) solutions of Sobolev regularity, for almost all values of the surface tension coefficient, and for a large set of time-frequencies. This is an existence result for a quasi-linear, Hamiltonian, reversible system of two autonomous pseudo-PDEs with small divisors. The proof is a combination of different techniques, such as a Nash-Moser scheme, microlocal analysis and bifurcation analysis.

  6. Experimental study on the standing-wave tube with tapered section and its extremely nonlinear standing-wave field

    Institute of Scientific and Technical Information of China (English)

    MIN Qi; YIN Yao; LI Xiaodong; LIU Ke

    2011-01-01

    A standing-wave tube with tapered section (STTS) was evolved from a standingwave tube with abrupt section (STAS) whose abrupt section was replaced with tapered section. The research was intended to compare the acoustic properties and the extremely nonlinear pure standing waves of STTS with those of STAS. The acoustic properties of the STTS were studied with transfer matrix. It was proved, like the STAS, that the STTS was dissonant standingwave tube. With its dissonant property, the 181 dB extremely nonlinear pure standing wave was obtained in the STTS excited at its first resonance frequency. Then the comparative experimental studies on the saturation properties of the extremely nonlinear standing waves were carried out in the STTS and the STAS with the same length. It was found that the STTS could suppress the harmonics and meanwhile reduce energy loss of the standing wave more effectively. Compared with the STAS, under the same voltage of loudspeaker, the STTS obtained a higher extremely nonlinear pure standing wave. Moreover, it was found for the STTS that the third harmonic of the third resonance frequency was close to the seventh resonance frequency of sound source impedance, to which the valley value of the sound pressure level transfer function corresponded. Because of this, the third harmonic increased rapidly with the increase of fundamental wave and tended to saturate.

  7. A Mathematical Prediction of Standing Waves

    Science.gov (United States)

    Higgins, Jon

    1970-01-01

    Presents a problem in standing waves that provides an example of the mathematics used by theoretical physicists to generate predictions of new phenomena from fundamental background knowledge. Mathematical analysis required to solve problem is accomplished by simple graphical processes. (BR)

  8. Enhanced current and voltage regulators for stand-alone applications

    DEFF Research Database (Denmark)

    Federico, de Bosio; Pastorelli, Michele; Antonio DeSouza Ribeiro, Luiz

    2016-01-01

    State feedback decoupling permits to achieve a better dynamic response for Voltage Source in stand-alone applications. The design of current and voltage regulators is performed in the discrete-time domain since it provides better accuracy and allows direct pole placement. As the attainable...... bandwidth of the current loop is mainly limited by computational and PWM delays, a lead compensator structure is proposed to overcome this limitation. The design of the voltage regulator is based on the Nyquist criterion, verifying to guarantee a high sensitivity peak. Discrete-time domain implementation...

  9. Residual liquefaction of seabed under standing waves

    DEFF Research Database (Denmark)

    Kirca, V.S. Ozgur; Sumer, B. Mutlu; Fredsøe, Jørgen

    2013-01-01

    This paper presents the results of an experimental study of the seabed liquefaction beneath standing waves. Silt (with d50 =0.070mm) was used in the experiments. Two kinds of measurements were carried out: pore water pressure measurements and water surface elevation measurements. These measurements...... were synchronized with video recording of the liquefaction process from the side. The ranges of the various quantities in the experiments were wave height H= 5.9-12.0 cm, wave period T= 1.09s, and water depth h=30 cm. The experiments show that the seabed liquefaction under standing waves, although...... with a diffusion coefficient equal to the coefficient of consolidation. The experiments further show that the number of waves to cause liquefaction at the nodal section appears to be equal to that experienced in progressive waves for the same wave height. © 2013 American Society of Civil Engineers....

  10. Standing waves in fiber-optic interferometers.

    Science.gov (United States)

    de Haan, V; Santbergen, R; Tijssen, M; Zeman, M

    2011-10-10

    A study is presented giving the response of three types of fiber-optic interferometers by which a standing wave through an object is investigated. The three types are a Sagnac, Mach-Zehnder and Michelson-Morley interferometer. The response of the Mach-Zehnder interferometer is similar to the Sagnac interferometer. However, the Sagnac interferometer is much harder to study because of the fact that one input port and output port coincide. Further, the Mach-Zehnder interferometer has the advantage that the output ports are symmetric, reducing the systematic effects. Examples of standing wave light absorption in several simple objects are given. Attention is drawn to the influence of standing waves in fiber-optic interferometers with weak-absorbing layers incorporated. A method is described for how these can be theoretically analyzed and experimentally measured. Further experiments are needed for a thorough comparison between theory and experiment.

  11. Future directions in standing-wave photoemission

    Energy Technology Data Exchange (ETDEWEB)

    Gray, Alexander X., E-mail: axgray@temple.edu

    2014-08-15

    Highlights: • Probing magnetic properties at the buried interface with SW-MCD. • Probing electronic structure at the buried interface with resonant SW-XPS and SW-HAXPES. • Probing momentum-resolved electronic structure at a buried interface with SWARPES. • Adding depth resolution to photoemission microscopy with standing-wave excitation. • Standing-wave localization, total reflection and waveguide effects. - Abstract: Over the past decade, standing-wave photoemission (SW-XPS) has evolved into a powerful and versatile non-destructive technique for probing element-specific electronic, magnetic, and structural properties of buried layers and interfaces with sub-nanometer depth resolution. In this article, I will discuss several promising future directions in this emergent field stemming from experimental and theoretical studies wherein SW-XPS is combined with other X-ray techniques, such as magnetic circular dichroism (MCD), hard X-ray photoemission spectroscopy (HAXPES), angle-resolved photoemission (ARPES), and photoemission microscopy (PEEM), adding extra dimensions to the measurement and thus widening the scope of scientific and technological questions accessible via the use of standing waves. I will further discuss examples of recently developed methods for X-ray standing-wave data analysis, which yield layer-resolved matrix-element-weighted densities of states at interfaces as well as Ångstrom-level changes in periodicity of synthetic superlattices. Finally, I will explore the possibility of localizing the standing waves near the surface and within a buried layer by the use of aperiodic superlattices, total reflection, and X-ray waveguide effects.

  12. Standing waves in fiber-optic interferometers

    NARCIS (Netherlands)

    De Haan, V.; Santbergen, R.; Tijssen, M.; Zeman, M.

    2011-01-01

    A study is presented giving the response of three types of fiber-optic interferometers by which a standing wave through an object is investigated. The three types are a Sagnac, Mach–Zehnder and Michelson–Morley interferometer. The response of the Mach–Zehnder interferometer is similar to the Sagnac

  13. Standing waves for discrete nonlinear Schrodinger equations

    OpenAIRE

    Ming Jia

    2016-01-01

    The discrete nonlinear Schrodinger equation is a nonlinear lattice system that appears in many areas of physics such as nonlinear optics, biomolecular chains and Bose-Einstein condensates. By using critical point theory, we establish some new sufficient conditions on the existence results of standing waves for the discrete nonlinear Schrodinger equations. We give an appropriate example to illustrate the conclusion obtained.

  14. Guitar Strings as Standing Waves: A Demonstration

    Science.gov (United States)

    Davis, Michael

    2007-01-01

    The study demonstrates the induction of one-dimensional standing waves, called "natural-harmonics" on a guitar to provide a unique tone. The analysis shows that a normally complex vibration is composed of a number of simple and discrete vibrations.

  15. Saturation process of nonlinear standing waves

    Institute of Scientific and Technical Information of China (English)

    马大猷; 刘克

    1996-01-01

    The sound pressure of the nonlinear standing waves is distorted as expected, but also tends to saturate as being found in standing-wave tube experiments with increasing sinusoidal excitation. Saturation conditions were not actually reached, owing to limited excitation power, but the evidence of tendency to saturation is without question. It is the purpose of this investigation to find the law of saturation from the existing experimental data. The results of curve fitting indicate that negative feedback limits the growth of sound pressure with increasing excitation, the growth of the fundamental and the second harmonic by the negative feedback of their sound pressures, and the growth of the third and higher harmonics, however, by their energies (sound pressures squared). The growth functions of all the harmonics are derived, which are confirmed by the experiments. The saturation pressures and their properties are found.

  16. Standing waves for discrete nonlinear Schrodinger equations

    Directory of Open Access Journals (Sweden)

    Ming Jia

    2016-07-01

    Full Text Available The discrete nonlinear Schrodinger equation is a nonlinear lattice system that appears in many areas of physics such as nonlinear optics, biomolecular chains and Bose-Einstein condensates. By using critical point theory, we establish some new sufficient conditions on the existence results of standing waves for the discrete nonlinear Schrodinger equations. We give an appropriate example to illustrate the conclusion obtained.

  17. Standing Sound Waves in Air with DataStudio

    Science.gov (United States)

    Kraftmakher, Yaakov

    2010-01-01

    Two experiments related to standing sound waves in air are adapted for using the ScienceWorkshop data-acquisition system with the DataStudio software from PASCO scientific. First, the standing waves are created by reflection from a plane reflector. The distribution of the sound pressure along the standing wave is measured. Second, the resonance…

  18. A Fresh Look at Longitudinal Standing Waves on a Spring

    Science.gov (United States)

    Rutherford, Casey

    2013-01-01

    Transverse standing waves produced on a string, as shown in Fig. 1, are a common demonstration of standing wave patterns that have nodes at both ends. Longitudinal standing waves can be produced on a helical spring that is mounted vertically and attached to a speaker, as shown in Fig. 2, and used to produce both node-node (NN) and node-antinode…

  19. Standing Sound Waves in Air with DataStudio

    Science.gov (United States)

    Kraftmakher, Yaakov

    2010-01-01

    Two experiments related to standing sound waves in air are adapted for using the ScienceWorkshop data-acquisition system with the DataStudio software from PASCO scientific. First, the standing waves are created by reflection from a plane reflector. The distribution of the sound pressure along the standing wave is measured. Second, the resonance…

  20. A Fresh Look at Longitudinal Standing Waves on a Spring

    Science.gov (United States)

    Rutherford, Casey

    2013-01-01

    Transverse standing waves produced on a string, as shown in Fig. 1, are a common demonstration of standing wave patterns that have nodes at both ends. Longitudinal standing waves can be produced on a helical spring that is mounted vertically and attached to a speaker, as shown in Fig. 2, and used to produce both node-node (NN) and node-antinode…

  1. A cylindrical standing wave ultrasonic motor using bending vibration transducer.

    Science.gov (United States)

    Liu, Yingxiang; Chen, Weishan; Liu, Junkao; Shi, Shengjun

    2011-07-01

    A cylindrical standing wave ultrasonic motor using bending vibration transducer was proposed in this paper. The proposed stator contains a cylinder and a bending vibration transducer. The two combining sites between the cylinder and the transducer locate at the adjacent wave loops of bending vibration of the transducer and have a distance that equal to the half wave length of bending standing wave excited in the cylinder. Thus, the bending mode of the cylinder can be excited by the bending vibration of the transducer. Two circular cone type rotors are pressed in contact to the end rims of the teeth, and the preload between the rotors and stator is accomplished by a spring and nut system. The working principle of the proposed motor was analyzed. The motion trajectories of teeth were deduced. The stator was designed and analyzed with FEM. A prototype motor was fabricated and measured. Typical output of the prototype is no-load speed of 165rpm and maximum torque of 0.45Nm at an exciting voltage of 200V(rms).

  2. Radiation from cosmic string standing waves

    Science.gov (United States)

    Olum; Blanco-Pillado

    2000-05-01

    We have simulated large-amplitude standing waves on an Abelian-Higgs cosmic string in classical lattice field theory. The radiation rate falls exponentially with wavelength, as one would expect from the field profile around a gauge string. Our results agree with those of Moore and Shellard, but not with those of Vincent, Antunes, and Hindmarsh. The radiation rate falls too rapidly to sustain a scaling solution via direct radiation of particles from string length. There is thus reason to doubt claims of strong constraints on cosmic string theories from cosmic ray observations.

  3. Stationary solid particle attractors in standing waves

    Energy Technology Data Exchange (ETDEWEB)

    Lappa, Marcello, E-mail: marlappa@unina.it, E-mail: marcello.lappa@telespazio.com [Telespazio, Via Gianturco 31, Napoli 80046 (Italy)

    2014-01-15

    The present analysis extends earlier theories on patterns formed by the spontaneous accumulation and ordering of solid particles in certain types of flow by considering the case in which the particle carrier flow has the typical features of a “standing wave.” For the first time an explanation for this phenomenon is elaborated through arguments based on the interplay between vorticity and wave-interference dynamics (following a deductive approach after the so-called phase-locking or “resonance” model originally introduced by Pushkin et al. [Phys. Rev. Lett. 106, 234501 (2011)] and later variants developed by Lappa [Phys. Fluids 25(1), 012101 (2013) and Lappa, Chaos 23(1), 013105 (2013)]). The results of dedicated numerical simulations are used in synergy with available experimental work. An interesting analogy is proposed with the famous Chladni's series of experiments on patterns formed by sand on vibrating plates.

  4. Stationary solid particle attractors in standing waves

    Science.gov (United States)

    Lappa, Marcello

    2014-01-01

    The present analysis extends earlier theories on patterns formed by the spontaneous accumulation and ordering of solid particles in certain types of flow by considering the case in which the particle carrier flow has the typical features of a "standing wave." For the first time an explanation for this phenomenon is elaborated through arguments based on the interplay between vorticity and wave-interference dynamics (following a deductive approach after the so-called phase-locking or "resonance" model originally introduced by Pushkin et al. [Phys. Rev. Lett. 106, 234501 (2011)] and later variants developed by Lappa [Phys. Fluids 25(1), 012101 (2013) and Lappa, Chaos 23(1), 013105 (2013)]). The results of dedicated numerical simulations are used in synergy with available experimental work. An interesting analogy is proposed with the famous Chladni's series of experiments on patterns formed by sand on vibrating plates.

  5. Onset behavior of standing wave thermoacoustic pressure wave generator

    Science.gov (United States)

    Mehta, Shreya; Desai, Keyur; Naik, Hemant Bhimbhai; Atrey, Milind

    2012-06-01

    A standing wave type thermoacoustic pressure wave generator for 300 Hz operating frequency is designed and developed for helium as a working fluid. The device is designed as a half wave length resonator. A parallel plate type SS 304 stack is designed and fabricated. An electric heater is used for heat supply to the hot end heat exchanger while a water cooled heat exchanger is used to maintain the other end of the stack near ambient temperature. An acoustic amplifier is used to amplify the pressure ratio generated. Experiments are conducted to study the onset behavior of pressure wave generator in terms of temperature range. Observations are recorded using piezoelectric pressure transducer. The results are obtained with different charging pressure and heat inputs. A pressure ratio of around 1.1 to 1.15 has been obtained using Nitrogen as a working fluid. The onset of thermoacoustic oscillations are studied for different filling pressure and for a range of hot end temperature.

  6. Standing Excitation Waves in the Heart Induced by Strong Alternating Electric Fields

    Science.gov (United States)

    Gray, Richard A.; Mornev, Oleg A.; Jalife, José; Aslanidi, Oleg V.; Pertsov, Arkady M.

    2001-10-01

    We studied the effect of sinusoidal electric fields on cardiac tissue both experimentally and numerically. We found that periodic forcing at 5-20 Hz using voltage applied in the bathing solution could stop the propagation of excitation waves by producing standing waves of membrane depolarization. These patterns were independent of the driving frequency in contrast to classical standing waves. The stimulus strength required for pattern formation was large compared to the excitation threshold. A novel tridomain representation of cardiac tissue was required to reproduce this behavior numerically.

  7. A 6D standing wave Braneworld

    CERN Document Server

    Sousa, L J S; Almeida, C A S

    2012-01-01

    We constructed a six-dimensional version of the standing wave model with an anisotropic 4-brane generated by a phantom-like scalar field. The model represents a braneworld where the compact (on-brane) dimension is assumed to be sufficiently small in order to describe our universe (hybrid compactification). The proposed geometry of the brane and its transverse manifold is non-static, unlike the majority of braneworld models presented in the literature. Furthermore, we have shown that the zero-mode scalar field is localized around the brane. While in the string-like defect the scalar field is localized on a brane with decreasing warp factor, here it was possible to perform the localization with an increasing warp factor.

  8. Voltage modulation of propagating spin waves in Fe

    Energy Technology Data Exchange (ETDEWEB)

    Nawaoka, Kohei; Shiota, Yoichi; Miwa, Shinji; Tamura, Eiiti [Graduate School of Engineering Science, Osaka University, Toyonaka, Osaka 560-8531 (Japan); CREST, Japan Science Technology, Kawaguchi, Saitama 332-0012 (Japan); Tomita, Hiroyuki; Mizuochi, Norikazu; Shinjo, Teruya [Graduate School of Engineering Science, Osaka University, Toyonaka, Osaka 560-8531 (Japan); Suzuki, Yoshishige, E-mail: suzuki-y@mp.es.osaka-u.ac.jp [Graduate School of Engineering Science, Osaka University, Toyonaka, Osaka 560-8531 (Japan); CREST, Japan Science Technology, Kawaguchi, Saitama 332-0012 (Japan); Display and Semiconductor Physics Department, Korea University, Sejong 339-700 (Korea, Republic of)

    2015-05-07

    The effect of a voltage application on propagating spin waves in single-crystalline 5 nm-Fe layer was investigated. Two micro-sized antennas were employed to excite and detect the propagating spin waves. The voltage effect was characterized using AC lock-in technique. As a result, the resonant field of the magnetostatic surface wave in the Fe was clearly modulated by the voltage application. The modulation is attributed to the voltage induced magnetic anisotropy change in ferromagnetic metals.

  9. A Voltage Controller in Photo-Voltaic System with Battery Storage for Stand-Alone Applications

    Directory of Open Access Journals (Sweden)

    Ganesh Dharmireddy

    2012-01-01

    Full Text Available This paper proposes the new voltage controller in photo-voltaic system for Stand-Alone Applications with battery energy storage. The output of the PV array is unregulated DC supply due to change in weather conditions. The maximum power is tracked with respect to temperature and irradiance levels by using DC-DC converter. The perturbation and observes algorithm is applied for maximum power point tracking (MPPT purpose. This algorithm is selected due to its ability to withstand against any parameter variation and having high efficiency. The solar cell array powers the steady state energy and the battery compensates the dynamic energy in the system. The aim of the control strategy is to control the SEPIC converter and bi-direction DC-DC converter to operate in suitable modes according to the condition of solar cell and battery, so as to coordinate the two sources of solar cell and battery supplying power and ensure the system operates with high efficiency and behaviors with good dynamic performance. The output of DC-DC converter is converted to AC voltage by using inverter.  The AC output voltage and frequency are regulated. A closed loop voltage control for inverter is done by using unipolar sine wave pulse width modulation (SPWM. The regulated AC voltage is fed to AC standalone loads or grid integration. The overall system is designed, developed and validated by using MATLAB-SIMULINK. The simulation results demonstrate the effective working of MPPT algorithm, control strategy and voltage controller with SPWM technique for inverter in AC standalone load applications.

  10. Theoretical Study on Standing Wave Thermoacoustic Engine

    Science.gov (United States)

    Kalra, S.; Desai, K. P.; Naik, H. B.; Atrey, M. D.

    Applications of thermoacoustic engines are not limited to driving pulse tube cryocoolers. The performance of a thermoacoustic engine is governed by various design parameters like type of resonator, stack geometry, frequency, type of working gas etc. and various operating parameters like heat input, charging pressure etc. It is very important to arrive at an optimum configuration of the engine for which a theoretical model is required. In the present work, a theoretical analysis, based on linear acoustic theory of a standing wave type half wavelength thermoacoustic engine is carried out using DeltaEC software. The system dimensions like length of resonator, stack, hot and cold heat exchangers are fixed with a helium-argon mixture as the working gas and a parallel plate type stack. Later on, two plate spacings, corresponding to helium-argon mixture and nitrogen gas, are used for carrying out analysis with helium, argon, nitrogen, carbon dioxide and helium-argon mixture as working gases of the system. The effect of charging pressure on the performance of the system is studied in terms of resonating frequency, onset temperature, pressure amplitude, acoustic power and efficiency. The conclusions derived from the analysis are reported in the paper.

  11. Standing Wave Solutions in Nonhomogeneous Delayed Synaptically Coupled Neuronal Networks

    Institute of Scientific and Technical Information of China (English)

    ZHANG Linghai; STONER Melissa Anne

    2012-01-01

    The authors establish the existence and stability of standing wave solutions of a nonlinear singularly perturbed system of integral differential equations and a nonlinear scalar integral differential equation.It will be shown that there exist six standing wave solutions ((u(x,t),w(x,t)) =(U(x),W(x)) to the nonlinear singularly perturbed system of integral differential equations.Similarly,there exist six standing wave solutions u(x,t) =U(x) to the nonlinear scalar integral differential equation.The main idea to establish the stability is to construct Evans functions corresponding to several associated eigenvalue problems.

  12. Transient Response Model of Standing Wave Piezoelectric Linear Ultrasonic Motor

    Institute of Scientific and Technical Information of China (English)

    SHI Yunlai; CHEN Chao; ZHAO Chunsheng

    2012-01-01

    A transient response model for describing the starting and stopping characteristics of the standing wave piezoelectric linear ultrasonic motor was presented.Based on the contact dynamic model,the kinetic equation of the motor was derived.The starting and stopping characteristics of the standing wave piezoelectric linear ultrasonic motor according to different loads,contact stiffness and inertia mass were described and analyzed,respectively.To validate the transient response model,a standing wave piezoelectric linear ultrasonic motor based on in-plane modes was used to carry out the simulation and experimental study.The corresponding results showed that the simulation of the motor performances based on the proposed model agreed well with the experimental results.This model will helpful to improve the stepping characteristics and the control flexibility of the standing wave piezoelectric linear ultrasonic motor.

  13. Standing wave brass-PZT square tubular ultrasonic motor.

    Science.gov (United States)

    Park, Soonho; He, Siyuan

    2012-09-01

    This paper reports a standing wave brass-PZT tubular ultrasonic motor. The motor is composed of a brass square tube with two teeth on each tube end. Four PZT plates are attached to the outside walls of the brass tube. The motor requires only one driving signal to excite vibration in a single bending mode to generate reciprocating diagonal trajectories of teeth on the brass tube ends, which drive the motor to rotate. Bi-directional rotation is achieved by exciting different pairs of PZT plates to switch the bending vibration direction. Through using the brass-PZT tube structure, the motor can take high magnitude vibration to achieve a high output power in comparison to PZT tube based ultrasonic motors. Prototypes are fabricated and tested. The dimension of the brass-PZT tube is 3.975mm×3.975mm×16mm. Measured performance is a no-load speed of >1000RPM, a stall torque of 370μNm and a maximum output power of 16 mW when a sinusoidal driving voltage of 50V is applied. The working frequencies of the motor are 46,050Hz (clockwise) and 46,200Hz (counter-clockwise).

  14. Standing magnetic wave on Ising ferromagnet: Nonequilibrium phase transition

    Science.gov (United States)

    Halder, Ajay; Acharyya, Muktish

    2016-12-01

    The dynamical response of an Ising ferromagnet to a plane polarised standing magnetic field wave is modelled and studied here by Monte Carlo simulation in two dimensions. The amplitude of standing magnetic wave is modulated along the direction x. We have detected two main dynamical phases namely, pinned and oscillating spin clusters. Depending on the value of field amplitude the system is found to undergo a phase transition from oscillating spin cluster to pinned as the system is cooled down. The time averaged magnetisation over a full cycle of magnetic field oscillations is defined as the dynamic order parameter. The transition is detected by studying the temperature dependences of the variance of the dynamic order parameter, the derivative of the dynamic order parameter and the dynamic specific heat. The dependence of the transition temperature on the magnetic field amplitude and on the wavelength of the magnetic field wave is studied at a single frequency. A comprehensive phase boundary is drawn in the plane described by the temperature and field amplitude for two different wavelengths of the magnetic wave. The variation of instantaneous line magnetisation during a period of magnetic field oscillation for standing wave mode is compared to those for the propagating wave mode. Also the probability that a spin at any site, flips, is calculated. The above mentioned variations and the probability of spin flip clearly distinguish between the dynamical phases formed by propagating magnetic wave and by standing magnetic wave in an Ising ferromagnet.

  15. Excitation of Standing Waves by an Electric Toothbrush

    Science.gov (United States)

    Cros, Ana; Ferrer-Roca, Chantal

    2006-01-01

    There are a number of ways of exciting standing waves in ropes and springs using non-commercial vibrators such as loudspeakers, jigsaws, motors, or a simple tuning fork, including the rhythmical shaking of a handheld Slinky. We have come up with a very simple and cheap way of exciting stationary waves in a string, which anyone, particularly…

  16. Standing wave acoustic levitation on an annular plate

    Science.gov (United States)

    Kandemir, Mehmet Hakan; Çalışkan, Mehmet

    2016-11-01

    In standing wave acoustic levitation technique, a standing wave is formed between a source and a reflector. Particles can be attracted towards pressure nodes in standing waves owing to a spring action through which particles can be suspended in air. This operation can be performed on continuous structures as well as in several numbers of axes. In this study an annular acoustic levitation arrangement is introduced. Design features of the arrangement are discussed in detail. Bending modes of the annular plate, known as the most efficient sound generation mechanism in such structures, are focused on. Several types of bending modes of the plate are simulated and evaluated by computer simulations. Waveguides are designed to amplify waves coming from sources of excitation, that are, transducers. With the right positioning of the reflector plate, standing waves are formed in the space between the annular vibrating plate and the reflector plate. Radiation forces are also predicted. It is demonstrated that small particles can be suspended in air at pressure nodes of the standing wave corresponding to a particular bending mode.

  17. High-Voltage Terminal Test of Test Stand for 1-MV Electrostatic Accelerator

    CERN Document Server

    Park, Sae-Hoon

    2015-01-01

    The Korea Multipurpose Accelerator Complex (KOMAC) has been developing a 300-kV test stand for a 1-MV electrostatic accelerator ion source. The ion source and accelerating tube will be installed in a high-pressure vessel. The ion source in the high-pressure vessel is required to have a high reliability. The test stand has been proposed and developed to confirm the stable operating conditions of the ion source. The ion source will be tested at the test stand to verify the long-time operating conditions. The test stand comprises a 300-kV high-voltage terminal, a battery for the ion-source power, a 60-Hz inverter, 200-MHz RF power, a 5-kV extraction power supply, a 300-kV accelerating tube, and a vacuum system. The results of the 300-kV high-voltage terminal tests are presented in this paper.

  18. A Standing-Wave Experiment with a Guitar

    Science.gov (United States)

    Inman, Fred W.

    2006-10-01

    When teaching standing waves, one often uses as examples musical instruments with strings, e.g., pianos, violins, and guitars. In today's popular music culture, young people may be more familiar with guitars than any other string instrument. I was helping my 15-year-old granddaughter make some repairs and adjustments to her electric guitar, and the subject of the spacing between the frets on the fingerboard was raised. I told her that the physics of standing waves and the equal tempered musical scale dictate the location of the frets. The purpose of this paper is to suggest that students might be introduced to the physics of standing waves using a guitar and to the formula for the fret locations. By measuring the positions of the frets, this formula can be tested.

  19. Standing Waves and Inquiry Using Water Droplets

    Science.gov (United States)

    Sinclair, Dina; Vondracek, Mark

    2015-01-01

    Most high school and introductory college physics classes study simple harmonic motion and various wave phenomena. With the majority of states adopting the Next Generation Science Standards and pushing students to explore the scientific process for themselves, there is a growing demand for hands-on inquiry activities that involve and develop more…

  20. Standing Waves and Inquiry Using Water Droplets

    Science.gov (United States)

    Sinclair, Dina; Vondracek, Mark

    2015-01-01

    Most high school and introductory college physics classes study simple harmonic motion and various wave phenomena. With the majority of states adopting the Next Generation Science Standards and pushing students to explore the scientific process for themselves, there is a growing demand for hands-on inquiry activities that involve and develop more…

  1. Standing Slow MHD Waves in Radiatively Cooling Coronal Loops

    Indian Academy of Sciences (India)

    K. S. Al-Ghafri

    2015-06-01

    The standing slow magneto-acoustic oscillations in cooling coronal loops are investigated. There are two damping mechanisms which are considered to generate the standing acoustic modes in coronal magnetic loops, namely, thermal conduction and radiation. The background temperature is assumed to change temporally due to optically thin radiation. In particular, the background plasma is assumed to be radiatively cooling. The effects of cooling on longitudinal slow MHD modes is analytically evaluated by choosing a simple form of radiative function, that ensures the temperature evolution of the background plasma due to radiation, coincides with the observed cooling profile of coronal loops. The assumption of low-beta plasma leads to neglecting the magnetic field perturbation and, eventually, reduces the MHD equations to a 1D system modelling longitudinal MHD oscillations in a cooling coronal loop. The cooling is assumed to occur on a characteristic time scale, much larger than the oscillation period that subsequently enables using the WKB theory to study the properties of standing wave. The governing equation describing the time-dependent amplitude of waves is obtained and solved analytically. The analytically derived solutions are numerically evaluated to give further insight into the evolution of the standing acoustic waves. We find that the plasma cooling gives rise to a decrease in the amplitude of oscillations. In spite of the reduction in damping rate caused by rising the cooling, the damping scenario of slow standing MHD waves strongly increases in hot coronal loops.

  2. Cooldown Measurements in a Standing Wave Thermoacoustic Refrigerator

    CERN Document Server

    Dhuley, R C

    2016-01-01

    Thermoacoustic Refrigerators (TARs) use acoustic power to generate cold temperatures. Apart from the operating frequency and the mean temperature of the working medium, the charging pressure and the dynamic pressure in the TAR govern its attainable cold temperature. The effect of charging pressure on the dynamic pressure in a loudspeaker driven gas filled standing wave column has been well understood. The present work aims to investigate the effect of charging pressure on the cold end temperature of a standing wave TAR. The cold end temperature lift and the cooldown for several changing pressures are reported. The effect of vacuum around the cold end on the TAR performance is also presented.

  3. Magnetization dynamics and spin pumping induced by standing elastic waves

    Science.gov (United States)

    Azovtsev, A. V.; Pertsev, N. A.

    2016-11-01

    The magnetization dynamics induced by standing elastic waves excited in a thin ferromagnetic film is described with the aid of micromagnetic simulations taking into account the magnetoelastic coupling between spins and lattice strains. Our calculations are based on the numerical solution of the Landau-Lifshitz-Gilbert equation comprising the damping term and the effective magnetic field with all relevant contributions. The simulations have been performed for 2-nm-thick F e81G a19 film dynamically strained by longitudinal and transverse standing waves with various frequencies, which span a wide range around the resonance frequency νres of coherent magnetization precession in unstrained F e81G a19 film. It is found that standing elastic waves give rise to complex local magnetization dynamics and spatially inhomogeneous dynamic patterns in the form of standing spin waves with the same wavelength. Remarkably, the amplitude of magnetization precession does not go to zero at nodes of these spin waves, which cannot be precisely described by simple analytical formulae. In the steady-state regime, magnetization oscillates with the frequency of the elastic wave, except in the case of longitudinal waves with frequencies well below νres, where the magnetization precesses with variable frequency strongly exceeding the wave frequency. The results obtained for the magnetization dynamics driven by elastic waves are used to calculate the spin current pumped from the dynamically strained ferromagnet into adjacent paramagnetic metal. Numerical calculations demonstrate that the transverse charge current in the paramagnetic layer, which is created by the spin current via inverse spin Hall effect, is high enough to be measured experimentally.

  4. The treatment of radioactive wastewater by ultrasonic standing wave method

    Energy Technology Data Exchange (ETDEWEB)

    Su-xia, Hou, E-mail: hsxljj@sina.com; Ji-jun, Luo; Bin, He; Ru-song, Li; Tao, Shen

    2014-06-01

    Highlights: • USWM can be considered as the green cleaning separation techniques. • A physical model of suspended radioactive particle is established. • A computer program is developed to achieve numerical calculation and analysis. • The experimental device for low-level radioactive wastes treatment is designed. • Lots of experimental data are used to analysis the influence of the parameters. - Abstract: The radiation hazards of radionuclide arising from the storage of nuclear weapons cannot be ignored to the operators. Ultrasonic standing wave methods can be considered as the green cleaning separation techniques with high efficiency. The application of ultrasonic standing wave methods for liquid radioactive wastes treatment requires solving many problems connected with the proper selection of the frequency and power of ultrasonic transducers, and the processing time, etc. Based on the model of one single suspended radioactive particle subjected to in the field of ultrasonic standing wave, the principle of the treatment of low-level radioactive wastewater by ultrasound was analyzed. The theoretical and simulation results show that under the action of ultrasonic standing wave, the particle will move toward the wave node plane, and the time of particle reaching the plane become shorter when the radius of particle and the frequency and power of ultrasound was enlarged. The experimental results show that the radioactive concentration of wastewater could be reduced from 400 Bq L{sup −1} to 9.3 Bq L{sup −1} and the decontamination efficiency was 97.68%. The decontamination efficiency could not be obviously improved by further increasing the treating time.

  5. The periodic standing-wave approximation: post-Minkowski computation

    CERN Document Server

    Beetle, Christopher; Hernández, Napoleón; Price, Richard H

    2007-01-01

    The periodic standing wave method studies circular orbits of compact objects coupled to helically symmetric standing wave gravitational fields. From this solution an approximation is extracted for the strong field, slowly inspiralling motion of black holes and binary stars. Previous work on this model has dealt with nonlinear scalar models, and with linearized general relativity. Here we present the results of the method for the post-Minkowski (PM) approximation to general relativity, the first step beyond linearized gravity. We compute the PM approximation in two ways: first, via the standard approach of computing linearized gravitational fields and constructing from them quadratic driving sources for second-order fields, and second, by solving the second-order equations as an ``exact'' nonlinear system. The results of these computations have two distinct applications: (i) The computational infrastructure for the ``exact'' PM solution will be directly applicable to full general relativity. (ii) The results w...

  6. Precision measurements in ion traps using slowly moving standing waves

    CERN Document Server

    Walther, A; Singer, K; Schmidt-Kaler, F

    2011-01-01

    The present paper describes the experimental implementation of a measuring technique employing a slowly moving, near resonant, optical standing wave in the context of trapped ions. It is used to measure several figures of merit that are important for quantum computation in ion traps and which are otherwise not easily obtainable. Our technique is shown to offer high precision, and also in many cases using a much simpler setup than what is normally used. We demonstrate here measurements of i) the distance between two crystalline ions, ii) the Lamb-Dicke parameter, iii) temperature of the ion crystal, and iv) the interferometric stability of a Raman setup. The exact distance between two ions, in units of standing wave periods, is very important for motional entangling gates, and our method offers a practical way of calibrating this distance in the typical lab situation.

  7. Traveling and Standing Waves in Coupled Pendula and Newton's Cradle

    Science.gov (United States)

    García-Azpeitia, Carlos

    2016-12-01

    The existence of traveling and standing waves is investigated for chains of coupled pendula with periodic boundary conditions. The results are proven by applying topological methods to subspaces of symmetric solutions. The main advantage of this approach comes from the fact that only properties of the linearized forces are required. This allows to cover a wide range of models such as Newton's cradle, the Fermi-Pasta-Ulam lattice, and the Toda lattice.

  8. Attractors and chaos of electron dynamics in electromagnetic standing wave

    CERN Document Server

    Esirkepov, Timur Zh; Koga, James K; Kando, Masaki; Kondo, Kiminori; Rosanov, Nikolay N; Korn, Georg; Bulanov, Sergei V

    2014-01-01

    The radiation reaction radically influences the electron motion in an electromagnetic standing wave formed by two super-intense counter-propagating laser pulses. Depending on the laser intensity and wavelength, either classical or quantum mode of radiation reaction prevail, or both are strong. When radiation reaction dominates, electron motion evolves to limit cycles and strange attractors. This creates a new framework for high energy physics experiments on an interaction of energetic charged particle beams and colliding super-intense laser pulses.

  9. Interaction of aerosol particles with a standing wave optical field

    Science.gov (United States)

    Curry, John J.

    2016-09-01

    Trajectories of spherical dielectric particles carried across an optical standing wave by a flowing medium are investigated. Trajectories are determined by a three-dimensional Monte Carlo calculation that includes drag forces, Brownian motion, and optical gradient forces. We analyze the case of polystyrene particles with radii of order 100 nm carried across a Gaussian-mode standing wave by slowly flowing air. Particles are injected into the flowing air from a small source area such as the end of a capillary tube. Different sizes are dispersed continuously in space on the opposite side of the standing wave, demonstrating a practical way to sort particles. Certain discrete values of particle size show no interaction with the optical field, independent of intensity. These particles can be sorted with exceptionally high resolution. For example, particles with radii of 275 nm can be sorted with 1 nm resolution. This sorting scheme has the advantages of accommodating a high throughput, producing a continuous stream of continuously dispersed particles, and exhibiting excellent size resolution. The Monte Carlo results are in agreement with those obtained by a much simpler, and faster, fluid calculation based on effective velocities and effective diffusion coefficients, both obtained by averaging trajectories over multiple fringes of the optical field.

  10. Nonlinear series resonance and standing waves in dual-frequency capacitive discharges

    Science.gov (United States)

    Wen, De-Qi; Kawamura, E.; Lieberman, M. A.; Lichtenberg, A. J.; Wang, You-Nian

    2017-01-01

    It is well-known that the nonlinear series resonance in a high frequency capacitive discharge enhances the electron power deposition and also creates standing waves which produce radially center-high rf voltage profiles. In this work, the dynamics of series resonance and wave effects are examined in a dual-frequency driven discharge, using an asymmetric radial transmission line model incorporating a Child law sheath. We consider a cylindrical argon discharge with a conducting electrode radius of 15 cm, gap length of 3 cm, with a base case having a 60 MHz high frequency voltage of 250 V and a 10 MHz low frequency voltage of 1000 V, with a high frequency phase shift {φ\\text{H}}=π between the two frequencies. For this phase shift there is only one sheath collapse, and the time-averaged spectral peaks of the normalized current density at the center are mainly centered on harmonic numbers 30 and 50 of the low frequency, corresponding to the first standing wave resonance frequency and the series resonance frequency, respectively. The effects of the waves on the series resonance dynamics near the discharge center give rise to significant enhancements in the electron power deposition, compared to that near the discharge edge. Adjusting the phase shift from π to 0, or decreasing the low frequency from 10 to 2 MHz, results in two or more sheath collapses, respectively, making the dynamics more complex. The sudden excitation of the perturbed series resonance current after the sheath collapse results in a current oscillation amplitude that is estimated from analytical and numerical calculations. Self-consistently determining the dc bias and including the conduction current is found to be important. The subsequent slow time variation of the high frequency oscillation is analyzed using an adiabatic theory.

  11. Stress wave propagation on standing trees. Part 2, Formation of 3D stress wave contour maps.

    Science.gov (United States)

    Juan Su; Houjiang Zhang; Xiping Wang

    2009-01-01

    Nondestructive evaluation (NDE) of wood quality in standing trees is an important procedure in the forest operational value chain worldwide. The goal of this paper is to investigate how a stress wave travel in a tree stem as it is introduced into the tree through a mechanical impact. Experimental stress wave data was obtained on freshly cut red pine logs in the...

  12. Adsorption-Mediated Mass Streaming in a Standing Acoustic Wave

    Science.gov (United States)

    Weltsch, Oren; Offner, Avshalom; Liberzon, Dan; Ramon, Guy Z.

    2017-06-01

    Oscillating flows can generate nonzero, time-averaged fluxes despite the velocity averaging zero over an oscillation cycle. Here, we report such a flux, a nonlinear resultant of the interaction between oscillating velocity and concentration fields. Specifically, we study a gas mixture sustaining a standing acoustic wave, where an adsorbent coats the solid boundary in contact with the gas mixture. It is found that the sound wave produces a significant, time-averaged preferential flux of a "reactive" component that undergoes a reversible sorption process. This effect is measured experimentally for an air-water vapor mixture. An approximate model is shown to be in good agreement with the experimental observations, and further reveals the interplay between the sound-wave characteristics and the properties of the gas-solid sorbate-sorbent pair. The preferential flux generated by this mechanism may have potential in separation processes.

  13. Current and Voltage Conveyors in Current- and Voltage-Mode Precision Full-Wave Rectifiers

    Directory of Open Access Journals (Sweden)

    J. Koton

    2011-04-01

    Full Text Available In this paper new versatile precision full-wave rectifiers using current and/or voltage conveyors as active elements and two diodes are presented. The performance of these circuit solutions is analysed and compared to the opamp based precision rectifier. To analyze the behavior of the functional blocks, the frequency dependent RMS error and DC transient value are evaluated for different values of input voltage amplitudes. Furthermore, experimental results are given that show the feasibilities of the conveyor based rectifiers superior to the corresponding operational amplifier based topology.

  14. CFD simulation of a 300 Hz thermoacoustic standing wave engine

    Science.gov (United States)

    Yu, Guoyao; Dai, W.; Luo, Ercang

    2010-09-01

    High frequency operation of standing wave thermoacoustic heat engines is attractive for space applications due to compact size and high reliability. To expedite practical use, further improvement and optimization should be based on deep understanding and quantitative analysis. This article focuses on using computational fluid dynamics (CFD) to investigate nonlinear phenomena and processes of a 300 Hz standing wave thermoacoustic engine (SWTE). The calculated model was tested in detail, which indicated that the co-axially stacked tube model was suitable for the simulation of SWTEs. Two methods of imposing temperature gradient across the stack were studied, and the processes of mean pressure increasing, pressure wave amplification and saturation were obtained under the thermal boundary condition of applying heating power. The acoustic fields were given, and the flow vortices and their evolution in both ends of the stack and resonator were observed. Moreover, a comparison between the simulation and experiments was made, which demonstrated the validity and power of the CFD simulation for characterizing complicated nonlinear phenomenon involved in the self-excited SWTEs.

  15. Modelling and Experiments of a Standing Wave Piezomotor

    DEFF Research Database (Denmark)

    Andersen, B.; Helbo, Jan; Blanke, Mogens

    The paper presents a new contact model for standing wave piezomotors. The contact model is based on the Hertz theory for normal contact deformations and elastic contact theory for tangential loads. The contact theory is simplified into a model with discrete springs for normal and tangential loads...... which allows the calculation of slip/stick transitions. Simulations show that tip trajectories in general cannot be prescribed. The paper presents the principle of a bending resonator. Experiments indicate that the bending vibrations are too small to generate rotor rotations. However, due to unintended...

  16. Modelling and Experiments of a Standing Wave Piezomotor

    DEFF Research Database (Denmark)

    Andersen, B.; Helbo, Jan; Blanke, Mogens

    2002-01-01

    The paper presents a new contact model for standing wave piezomotors. The contact model is based on the Hertz theory for normal contact deformations and elastic contact theory for tangential loads. The contact theory is simplified into a model with discrete springs for normal and tangential loads...... which allows the calculation of slip/stick transitions. Simulations show that tip trajectories in general cannot be prescribed. The paper presents the principle of a bending resonator. Experiments indicate that the bending vibrations are too small to generate rotor rotations. However, due to unintended...

  17. Attractors and chaos of electron dynamics in electromagnetic standing waves

    Energy Technology Data Exchange (ETDEWEB)

    Esirkepov, Timur Zh. [QuBS, Japan Atomic Energy Agency, Kizugawa, Kyoto 619-0215 (Japan); Bulanov, Stepan S. [University of California, Berkeley, CA 94720 (United States); Koga, James K.; Kando, Masaki; Kondo, Kiminori [QuBS, Japan Atomic Energy Agency, Kizugawa, Kyoto 619-0215 (Japan); Rosanov, Nikolay N. [Vavilov State Optical Institute, Saint-Petersburg 199034 (Russian Federation); Korn, Georg [ELI Beamline Facility, Institute of Physics, Czech Academy of Sciences, Prague 18221 (Czech Republic); Bulanov, Sergei V., E-mail: bulanov.sergei@jaea.go.jp [QuBS, Japan Atomic Energy Agency, Kizugawa, Kyoto 619-0215 (Japan)

    2015-09-25

    In an electromagnetic standing wave formed by two super-intense colliding laser pulses, radiation reaction totally modifies the electron motion. The quantum corrections to the electron motion and the radiation reaction force can be independently small or large, depending on the laser intensity and wavelength, thus dividing the parameter space into 4 domains. The electron motion evolves to limit cycles and strange attractors when radiation reaction dominates. This creates a new framework for high energy physics experiments on the interaction of energetic charged particle beams and colliding super-intense laser pulses.

  18. Two Mode Resonator and Contact Model for Standing Wave Piezomotor

    DEFF Research Database (Denmark)

    Andersen, B.; Blanke, Mogens; Helbo, J.

    2001-01-01

    The paper presents a model for a standing wave piezoelectric motor with a two bending mode resonator. The resonator is modelled using Hamilton's principle and the Rayleigh-Ritz method. The contact is modelled using the Lagrange Multiplier method under the assumption of slip and it is showed how...... to solve the set of differential-algebraic equations. Detailled simulations show resonance frequencies as function of the piezoelement's position, tip trajectories and contact forces. The paper demonstrates that contact stiffness and stick should be included in such model to obtain physically realistic...

  19. A standing wave braneworld and associated Sturm-Liouville problem

    CERN Document Server

    Gogberashvili, Merab; Malagon-Morejon, Dagoberto

    2010-01-01

    We present a consistent derivation of the recently proposed 5D standing wave braneworld generated by gravity coupled to a phantom-like scalar field by introducing an energy-momentum tensor on the brane with different tensions along different space-time directions and explicitly solve the corresponding junction conditions. We also analyze the Sturm-Liouville problem associated to the correct localization condition of the transverse to the brane metric and scalar fields. It is shown that this condition restricts the physically meaningful space of solutions for the localization of the fluctuations of the model.

  20. Motion of a charge in a superstrong electromagnetic standing wave

    Science.gov (United States)

    Esirkepov, Timur Z.; Bulanov, Stepan S.; Koga, James K.; Kando, Masaki; Kondo, Kiminori; Rosanov, Nikolay N.; Korn, Georg; Bulanov, Sergei V.

    2015-05-01

    Radiation reaction radically influences the electron motion in an electromagnetic standing wave formed by two super-intense colliding laser pulses. Depending on the laser intensity and wavelength, the quantum corrections to the electron motion and the radiation reaction force can be independently small or large, thus dividing the parameter space into 4 regions. When radiation reaction dominates, the electron motion evolves to limit cycles and strange attractors. This creates a new framework for high energy physics experiments on the interaction of energetic charged particle beams and colliding super-intense laser pulses.

  1. Attractors and chaos of electron dynamics in electromagnetic standing waves

    Science.gov (United States)

    Esirkepov, Timur Zh.; Bulanov, Stepan S.; Koga, James K.; Kando, Masaki; Kondo, Kiminori; Rosanov, Nikolay N.; Korn, Georg; Bulanov, Sergei V.

    2015-09-01

    In an electromagnetic standing wave formed by two super-intense colliding laser pulses, radiation reaction totally modifies the electron motion. The quantum corrections to the electron motion and the radiation reaction force can be independently small or large, depending on the laser intensity and wavelength, thus dividing the parameter space into 4 domains. The electron motion evolves to limit cycles and strange attractors when radiation reaction dominates. This creates a new framework for high energy physics experiments on the interaction of energetic charged particle beams and colliding super-intense laser pulses.

  2. Exchange anisotropy pinning of a standing spin-wave mode

    Science.gov (United States)

    Magaraggia, R.; Kennewell, K.; Kostylev, M.; Stamps, R. L.; Ali, M.; Greig, D.; Hickey, B. J.; Marrows, C. H.

    2011-02-01

    Standing spin waves in a thin film are used as sensitive probes of interface pinning induced by an antiferromagnet through exchange anisotropy. Using coplanar waveguide ferromagnetic resonance, pinning of the lowest energy spin-wave thickness mode in Ni80Fe20/Ir25Mn75 exchange-biased bilayers was studied for a range of Ir25Mn75 thicknesses. We show that pinning of the standing mode can be used to amplify, relative to the fundamental resonance, frequency shifts associated with exchange bias. The shifts provide a unique “fingerprint” of the exchange bias and can be interpreted in terms of an effective ferromagnetic film thickness and ferromagnet-antiferromagnet interface anisotropy. Thermal effects are studied for ultrathin antiferromagnetic Ir25Mn75 thicknesses, and the onset of bias is correlated with changes in the pinning fields. The pinning strength magnitude is found to grow with cooling of the sample, while the effective ferromagnetic film thickness simultaneously decreases. These results suggest that exchange bias involves some deformation of magnetic order in the interface region.

  3. Thin film characterization by resonantly excited internal standing waves

    Energy Technology Data Exchange (ETDEWEB)

    Di Fonzio, S. [SINCROTRONE TRIESTE, Trieste (Italy)

    1996-09-01

    This contribution describes how a standing wave excited in a thin film can be used for the characterization of the properties of the film. By means of grazing incidence X-ray reflectometry one can deduce the total film thickness. On the other hand in making use of a strong resonance effect in the electric field intensity distribution inside a thin film on a bulk substrate one can learn more about the internal structure of the film. The profile of the internal standing wave is proven by diffraction experiments. The most appropriate non-destructive technique for the subsequent thin film characterization is angularly dependent X-ray fluorescence analysis. The existence of the resonance makes it a powerful tool for the detection of impurities and of ultra-thin maker layers, for which the position can be determined with very high precision (about 1% of the total film thickness). This latter aspect will be discussed here on samples which had a thin Ti marker layer at different positions in a carbon film. Due to the resonance enhancement it was still possible to perform these experiments with a standard laboratory x-ray tube and with standard laboratory tool for marker or impurity detection in thin films.

  4. Contact Analysis and Modeling of Standing Wave Linear Ultrasonic Motor

    Institute of Scientific and Technical Information of China (English)

    SHI Yunlai; ZHAO Chunsheng; ZHANG Jianhui

    2011-01-01

    A contact model for describing the contact mechanics between the stator and slider of the standing wave linear ultrasonic motor was presented.The proposed model starts from the assumption that the vibration characteristics of the stator is not affected by the contact process.A modified friction models was used to analyze the contact problems.Firstly,the dynamic normal contact force,interface friction force,and steady-state characteristics were analyzed.Secondly,the influences of the contact layer material,the dynamic characteristics of the stator,and the pre-load on motor performance were simulated.Finally,to validate the contact model,a linear ultrasonic motor based on in-plane modes was used as an example.The corresponding results show that a set of simulation of motor performances based on the proposed contact mechanism is in good agreement with experimental results.This model is helpful to understanding the operation principle of the standing wave linear motor and thus contributes to the design of these tvpes of motor.

  5. A standing wave-type noncontact linear ultrasonic motor.

    Science.gov (United States)

    Hu, J; Li, G; Chan, H L; Choy, C L

    2001-05-01

    In this study, a novel standing wave-type noncontact linear ultrasonic motor is proposed and analyzed. This linear ultrasonic motor uses a properly controlled ultrasonic standing wave to levitate and drive a slider. A prototype of the motor was constructed by using a wedge-shaped aluminum stator, which was placed horizontally and driven by a multilayer PZT vibrator. The levitation and motion of the slider were observed. Assuming that the driving force was generated by the turbulent acoustic streaming in the boundary air layer next to the bottom surface of the slider, a theoretical model was developed. The calculated characteristics of this motor were found to agree quite well with the experimental results. Based on the experimental and theoretical results, guidelines for increasing the displacement and speed of the slider were obtained. It was found that increasing the stator vibration displacement, or decreasing the gradient of the stator vibration velocity and the weight per unit area of the slider, led to an increase of the slider displacement. It was also found that increasing the amplitude and gradient of the stator vibration velocity, or decreasing the weight per unit area of the slider and the driving frequency, gave rise to an increase of the slider speed. There exists an optimum roughness of the bottom surface of the slider at which the slider speed has a maximum.

  6. Influence of mass imperfections on the evolution of standing waves in slowly rotating spherical bodies

    CSIR Research Space (South Africa)

    Shatalov, MY

    2011-01-01

    Full Text Available Standing waves can exist as stable vibrating patterns in perfect structures such as spherical bodies, and inertial rotation of the body causes precession (Bryan’seffect). However, an imperfection such as light mass anisotropy destroys the standing...

  7. Photo-Ionization of Hydrogen Atom in a Circularly Polarized Standing Electromagnetic Wave

    Institute of Scientific and Technical Information of China (English)

    LIU Xiang-Tao; ZHANG Qi-Ren; WANG Wan-Zhang

    2004-01-01

    Applying time-independent non-perturbative formalism to the photo-ionization of hydrogen atom immersed in a strong circularly polarized standing electromagnetic wave, we calculate the shift of energy levels and the distortion of wave functions for the hydrogen atom, the ionization cross section induced by the standing wave, and the angular distribution of photoelectrons and obtain some interesting results.

  8. Heteroclinic standing waves in defocussing DNLS equations -- Variational approach via energy minimization

    CERN Document Server

    Herrmann, Michael

    2010-01-01

    We study heteroclinic standing waves (dark solitons) in discrete nonlinear Schr\\"{o}dinger equations with defocussing nonlinearity. Our main result is a quite elementary existence proof for waves with monotone and odd profile, and relies on minimizing an appropriately defined energy functional. We also study the continuum limit and the numerical approximation of standing waves.

  9. ORBITAL INSTABILITY OF STANDING WAVES FOR THE COUPLED NONLINEAR KLEIN-GORDON EQUATIONS

    Institute of Scientific and Technical Information of China (English)

    Gan Zaihui; Guo Boling; Zhang Jian

    2008-01-01

    This paper deals with a type of standing waves for the coupled nonlin-ear Klein-Gordon equations in three space dimensions. First we construct a suitable constrained variational problem and obtain the existence of the standing waves with ground state by using variational argument. Then we prove the orbital instability of the standing waves by defining invariant sets and applying some priori estimates.

  10. Slot-coupled CW standing wave accelerating cavity

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Shaoheng; Rimmer, Robert; Wang, Haipeng

    2017-05-16

    A slot-coupled CW standing wave multi-cell accelerating cavity. To achieve high efficiency graded beta acceleration, each cell in the multi-cell cavity may include different cell lengths. Alternatively, to achieve high efficiency with acceleration for particles with beta equal to 1, each cell in the multi-cell cavity may include the same cell design. Coupling between the cells is achieved with a plurality of axially aligned kidney-shaped slots on the wall between cells. The slot-coupling method makes the design very compact. The shape of the cell, including the slots and the cone, are optimized to maximize the power efficiency and minimize the peak power density on the surface. The slots are non-resonant, thereby enabling shorter slots and less power loss.

  11. Unified relativistic physics from a standing wave particle model

    CERN Document Server

    Vera, R A

    1995-01-01

    An extremely simple and unified base for physics comes out by starting all over from a single postulate on the common nature of matter and stationary forms of radiation quanta. Basic relativistic, gravitational (G) and quantum mechanical properties of a standing wave particle model have been derived. This has been done from just dual properties of radiation's and strictly homogeneous relationships for nonlocal cases in G fields. This way reduces the number of independent variables and puts into relief (and avoid) important inhomogeneity errors of some G theories. It unifies and accounts for basic principles and postulates physics. The results for gravity depend on linear radiation properties but not on arbitrary field relations. They agree with the conventional tests. However they have some fundamental differences with current G theories. The particle model, at a difference of the conventional theories, also fixes well-defined cosmological and astrophysical models that are different from the rather convention...

  12. Design and simulation of a standing wave oscillator based PLL

    Institute of Scientific and Technical Information of China (English)

    Wei ZHANG; You-de HU; Li-rong ZHENG

    2016-01-01

    A standing wave oscillator (SWO) is a perfect clock source which can be used to produce a high frequency clock signal with a low skew and high reliability. However, it is difficult to tune the SWO in a wide range of frequencies. We introduce a frequency tunable SWO which uses an inversion mode metal-oxide-semiconductor (IMOS) field-effect transistor as a varactor, and give the simulation results of the frequency tuning range and power dissipation. Based on the frequency tunable SWO, a new phase locked loop (PLL) architecture is presented. This PLL can be used not only as a clock source, but also as a clock distribution network to provide high quality clock signals. The PLL achieves an approximately 50% frequency tuning range when designed in Global Foundry 65 nm 1P9M complementary metal-oxide-semiconductor (CMOS) technology, and can be used directly in a high performance multi-core microprocessor.

  13. Suspension of atoms and gravimetry using a pulsed standing wave

    CERN Document Server

    Hughes, K J; Sackett, C A

    2009-01-01

    Atoms from an otherwise unconfined 87Rb condensate are shown to be suspended against gravity using repeated reflections from a pulsed optical standing wave. Reflection efficiency was optimized using a triple-pulse sequence that, theoretically, provides accuracies better than 99.9%. Experimentally, up to 100 reflections are observed, leading to dynamical suspension for over 100 ms. The velocity sensitivity of the reflections can be used to determine the local gravitational acceleration. Further, a gravitationally sensitive atom interferometer was implemented using the suspended atoms, with packet coherence maintained for a similar time. These techniques could be useful for the precise measurement of gravity when it is impractical to allow atoms to fall freely over a large distance.

  14. Voltage mode electronically tunable full-wave rectifier

    Science.gov (United States)

    Petrović, Predrag B.; Vesković, Milan; Đukić, Slobodan

    2017-01-01

    The paper presents a new realization of bipolar full-wave rectifier of input sinusoidal signals, employing one MO-CCCII (multiple output current controlled current conveyor), a zero-crossing detector (ZCD), and one resistor connected to fixed potential. The circuit provides the operating frequency up to 10 MHz with increased linearity and precision in processing of input voltage signal, with a very low harmonic distortion. The errors related to the signal processing and errors bound were investigated and provided in the paper. The PSpice simulations are depicted and agree well with the theoretical anticipation. The maximum power consumption of the converter is approximately 2.83 mW, at ±1.2 V supply voltages.

  15. Separation of bacterial spores from flowing water in macro-scale cavities by ultrasonic standing waves

    CERN Document Server

    Lipkens, B; Costolo, M; Stevens, A; Rietman, Edward

    2010-01-01

    The separation of micron-sized bacterial spores (Bacillus cereus) from a steady flow of water through the use of ultrasonic standing waves is demonstrated. An ultrasonic resonator with cross-section of 0.0254 m x 0.0254 m has been designed with a flow inlet and outlet for a water stream that ensures laminar flow conditions into and out of the resonator section of the flow tube. A 0.01905-m diameter PZT-4, nominal 2-MHz transducer is used to generate ultrasonic standing waves in the resonator. The acoustic resonator is 0.0356 m from transducer face to the opposite reflector wall with the acoustic field in a direction orthogonal to the water flow direction. At fixed frequency excitation, spores are concentrated at the stable locations of the acoustic radiation force and trapped in the resonator region. The effect of the transducer voltage and frequency on the efficiency of spore capture in the resonator has been investigated. Successful separation of B. cereus spores from water with typical volume flow rates of...

  16. Trial Operation of a Stand-alone Wave Power System Successful

    Institute of Scientific and Technical Information of China (English)

    2005-01-01

    @@ A group of scientists from the CAS Guangzhou Institute of Energy Conversion succeeded on January 9 in their first sea trial of a stand-alone wave power system, marking significant progress in generating stable electricity with wave energy.

  17. Coherent control of light-matter interactions in polarization standing waves

    Science.gov (United States)

    Fang, Xu; MacDonald, Kevin F.; Plum, Eric; Zheludev, Nikolay I.

    2016-08-01

    We experimentally demonstrate that standing waves formed by two coherent counter-propagating light waves can take a variety of forms, offering new approaches to the interrogation and control of polarization-sensitive light-matter interactions in ultrathin (subwavelength thickness) media. In contrast to familiar energy standing waves, polarization standing waves have constant electric and magnetic energy densities and a periodically varying polarization state along the wave axis. counterintuitively, anisotropic ultrathin (meta)materials can be made sensitive or insensitive to such polarization variations by adjusting their azimuthal angle.

  18. What are the frequencies of standing magnetopause surface waves?

    CERN Document Server

    Archer, Martin

    2014-01-01

    We estimate, for the first time, the distribution of standing magnetopause surface wave (also called Kruskal-Schwartzschild mode) frequencies using realistic models of the magnetosphere and magnetosheath utilising an entire solar cycle's worth of solar wind data. Under non-storm times or northward interplanetary magnetic field (IMF), the most likely fundamental frequency is calculated to be 0.64$\\pm$0.06 mHz, consistent with that previously inferred from observed oscillation periods of the boundary. However, the distributions exhibit significant spread (of order $\\pm$0.3 mHz), much larger than suggested by proponents of discrete, stable "magic" frequencies of magnetospheric oscillation. The frequency is found to be most dependent on the solar wind speed, southward component of the IMF and the Dst index, with the latter two being due to the erosion of the magnetosphere by reconnection and the former an effect of the expression for the surface wave phase speed. Finally, the occurrence of Kruskal-Schwartzschild ...

  19. Standing surface acoustic wave (SSAW)-based microfluidic cytometer.

    Science.gov (United States)

    Chen, Yuchao; Nawaz, Ahmad Ahsan; Zhao, Yanhui; Huang, Po-Hsun; McCoy, J Phillip; Levine, Stewart J; Wang, Lin; Huang, Tony Jun

    2014-03-07

    The development of microfluidic chip-based cytometers has become an important area due to their advantages of compact size and low cost. Herein, we demonstrate a sheathless microfluidic cytometer which integrates a standing surface acoustic wave (SSAW)-based microdevice capable of 3D particle/cell focusing with a laser-induced fluorescence (LIF) detection system. Using SSAW, our microfluidic cytometer was able to continuously focus microparticles/cells at the pressure node inside a microchannel. Flow cytometry was successfully demonstrated using this system with a coefficient of variation (CV) of less than 10% at a throughput of ~1000 events s(-1) when calibration beads were used. We also demonstrated that fluorescently labeled human promyelocytic leukemia cells (HL-60) could be effectively focused and detected with our SSAW-based system. This SSAW-based microfluidic cytometer did not require any sheath flows or complex structures, and it allowed for simple operation over a wide range of sample flow rates. Moreover, with the gentle, bio-compatible nature of low-power surface acoustic waves, this technique is expected to be able to preserve the integrity of cells and other bioparticles.

  20. SQUEEZING PROPERTIES OF A TRAPPED ION IN THE STANDING-WAVE LASER

    Institute of Scientific and Technical Information of China (English)

    FANG MAO-FA; LIU XIANG

    2001-01-01

    We investigate the squeezing properties of a trapped ion in a standing-wave laser. Our results show that the squeezing of a trapped ion in the standing-wave laser is dependent on its position in the latter, the detuning parameter and the initial average phonon number.

  1. On functional equations leading to exact solutions for standing internal waves

    NARCIS (Netherlands)

    Beckebanze, F.; Keady, G.

    The Dirichlet problem for the wave equation is a classical example of a problem which is ill-posed. Nevertheless, it has been used to model internal waves oscillating harmonically in time, in various situations, standing internal waves amongst them. We consider internal waves in two-dimensional

  2. Noise-induced standing waves in oscillatory systems with time-delayed feedback

    CERN Document Server

    Stich, Michael

    2016-01-01

    In oscillatory reaction-diffusion systems, time-delay feedback can lead to the instability of uniform oscillations with respect to formation of standing waves. Here, we investigate how the presence of additive, Gaussian white noise can induce the appearance of standing waves. Combining analytical solutions of the model with spatio-temporal simulations, we find that noise can promote standing waves in regimes where the deterministic uniform oscillatory modes are stabilized. As the deterministic phase boundary is approached, the spatio-temporal correlations become stronger, such that even small noise can induce standing waves in this parameter regime. With larger noise strengths, standing waves could be induced at finite distances from the (deterministic) phase boundary. The overall dynamics is defined through the interplay of noisy forcing with the inherent reaction-diffusion dynamics.

  3. Extracting Information from the Atom-Laser Wave Function UsingInterferometric Measurement with a Laser Standing-Wave Grating

    Institute of Scientific and Technical Information of China (English)

    刘正东; 武强; 曾亮; 林宇; 朱诗尧

    2001-01-01

    The reconstruction of the atom-laser wave function is performed using an interferometric measurement with a standing-wave grating, and the results of this scheme are studied. The relations between the measurement data and the atomic wave function are also presented. This scheme is quite applicable and effectively avoids the initial random phase problem of the method that employs the laser running wave. The information which is encoded in the atom-laser wave is extracted.

  4. Re-entry communication through a plasma sheath using standing wave detection and adaptive data rate control

    Science.gov (United States)

    Xie, Kai; Yang, Min; Bai, Bowen; Li, Xiaoping; Zhou, Hui; Guo, Lixin

    2016-01-01

    Radio blackout during the re-entry has puzzled the aerospace industry for decades and has not yet been completely resolved. To achieve a continuous data link in the spacecraft's re-entry period, a simple and practicable communication method is proposed on the basis that (1) the electromagnetic-wave backscatter of the plasma sheath affects the voltage standing wave ratio (VSWR) of the antenna, and the backscatter is negatively correlated to transmission components, and (2) the transmission attenuation caused by the plasma sheath reduces the channel capacity. We detect the voltage standing wave ratio changes of the antenna and then adjust the information rate to accommodate the varying channel capacity, thus guaranteeing continuous transmission (for fewer critical data). The experiment was carried out in a plasma generator with an 18-cm-thick and 30-cm-diameter hollow propagation path, and the adaptive communication was implemented using spread spectrum frequency, shift key modulation with a variable spreading factor. The experimental results indicate that, when the over-threshold of VSWR was detected, the bit rate reduced to 250 bps from 4 Mbps automatically and the tolerated plasma density increased by an order of magnitude, which validates the proposed scheme. The proposed method has little additional cost, and the adaptive control does not require a feedback channel. The method is therefore applicable to data transmission in a single direction, such as that of a one-way telemetry system.

  5. Scaling-up ultrasound standing wave enhanced sedimentation filters.

    Science.gov (United States)

    Prest, Jeff E; Treves Brown, Bernard J; Fielden, Peter R; Wilkinson, Stephen J; Hawkes, Jeremy J

    2015-02-01

    Particle concentration and filtration is a key stage in a wide range of processing industries and also one that can be present challenges for high throughput, continuous operation. Here we demonstrate some features which increase the efficiency of ultrasound enhanced sedimentation and could enable the technology the potential to be scaled up. In this work, 20 mm piezoelectric plates were used to drive 100 mm high chambers formed from single structural elements. The coherent structural resonances were able to drive particles (yeast cells) in the water to nodes throughout the chamber. Ultrasound enhanced sedimentation was used to demonstrate the efficiency of the system (>99% particle clearance). Sub-wavelength pin protrusions were used for the contacts between the resonant chamber and other elements. The pins provided support and transferred power, replacing glue which is inefficient for power transfer. Filtration energies of ∼4 J/ml of suspension were measured. A calculation of thermal convection indicates that the circulation could disrupt cell alignment in ducts >35 mm high when a 1K temperature gradient is present; we predict higher efficiencies when this maximum height is observed. For the acoustic design, although modelling was minimal before construction, the very simple construction allowed us to form 3D models of the nodal patterns in the fluid and the duct structure. The models were compared with visual observations of particle movement, Chladni figures and scanning laser vibrometer mapping. This demonstrates that nodal planes in the fluid can be controlled by the position of clamping points and that the contacts could be positioned to increase the efficiency and reliability of particle manipulations in standing waves.

  6. Particle dynamics and pair production in tightly focused standing wave

    Science.gov (United States)

    Jirka, M.; Klimo, O.; Vranić, M.; Weber, S.; Korn, G.

    2017-05-01

    With the advent of 10 PW laser facilities, new regimes of laser-matter interaction are opening since effects of quantum electrodynamics, such as electron-positron pair production and cascade development, start to be important. The dynamics of light charged particles, such as electrons and positrons, is affected by the radiation reaction force. This effect can strongly influence the interaction of intense laser pulses with matter since it lowers the energy of emitting particles and transforms their energy to the gamma radiation. Consequently, electron-positron pairs can be generated via Breit-Wheeler process. To study this new regime of interaction, numerical simulations are required. With their help it is possible to predict and study quantum effects which may occur in future experiments at modern laser facilities. In this work we present results of electron interaction with an intense standing wave formed by two colliding laser pulses. Due to the necessity to achieve ultra intense laser field, the laser beam has to be focused to a μm-diameter spot. Since the paraxial approximation is not valid for tight focusing, the appropriate model describing the tightly focused laser beam has to be employed. In tightly focused laser beam the longitudinal component of the electromagnetic field becomes significant and together with the ponderomotive force they affect the dynamics of interacting electrons and also newly generated Breit-Wheeler electron-positron pairs. Using the Particle-In-Cell code we study electron dynamics, gamma radiation and pair production in such a configuration for linear polarization and different types of targets.

  7. Analysis on Non-Resonance Standing Waves and Vibration Tracks of Strings

    Science.gov (United States)

    Fang, Tian-Shen

    2007-01-01

    This paper presents an experimental technique to observe the vibration tracks of string standing waves. From the vibration tracks, we can analyse the vibration directions of harmonic waves. For the harmonic wave vibrations of strings, when the driving frequency f[subscript s] = Nf[subscript n] (N = 1, 2, 3, 4,...), both resonance and non-resonance…

  8. Standing Waves of the Inhomogeneous Klein-Gordon Equations with Critical Exponent

    Institute of Scientific and Technical Information of China (English)

    Zai Hui GAN; Jian ZHANG

    2006-01-01

    This paper is concerned with the standing wave in the inhomogeneous nonlinear Klein-Gordon equations with critical exponent. Firstly, we obtain the existence of standing waves associated with the ground states by using variational calculus as well as a compactness lemma. Next, we establish some sharp conditions for global existence in terms of the characteristics of the ground state. Then,we show that how small the initial data are for the global solutions to exist. Finally, we prove the instability of the standing wave by combining the former results.

  9. The global coherence initiative: creating a coherent planetary standing wave.

    Science.gov (United States)

    McCraty, Rollin; Deyhle, Annette; Childre, Doc

    2012-03-01

    via biological, electromagnetic, and nonlocal fields, it stands to reason that humans can work together in a co-creative relationship to consciously increase the coherence in the global field environment, which in turn distributes this information to all living systems within the field. GCI was established to help facilitate the shift in global consciousness from instability and discord to balance, cooperation, and enduring peace. A primary goal of GCI is to test the hypothesis that large numbers of people when in a heart-coherent state and holding a shared intention can encode information on the earth's energetic and geomagnetic fields, which act as carrier waves of this physiologically patterned and relevant information. In order to conduct this research, a global network of 12 to 14 ultrasensitive magnetic field detectors specifically designed to measure the earth's magnetic resonances is being installed strategically around the planet. More important is GCI's primary goal to motivate as many people as possible to work together in a more coherent and collaborative manner to increase the collective human consciousness. If we are persuaded that not only external fields of solar and cosmic origins but also human attention and emotion can directly affect the physical world and the mental and emotional states of others (consciousness), it broadens our view of what interconnectedness means and how it can be intentionally utilized to shape the future of the world we live in. It implies that our attitudes, emotions, and intentions matter and that coherent, cooperative intent can have positive effects. GCI hypothesizes that when enough individuals and social groups increase their coherence baseline and utilize that increased coherence to intentionally create a more coherent standing reference wave in the global field, it will help increase global consciousness. This can be achieved when an increasing number of people move towards more balanced and self-regulated emotions

  10. Inverter and Motor Model Adaptation at Stand-Still Using Reference Voltages and Measured Currents

    DEFF Research Database (Denmark)

    Rasmussen, Henrik; Tønnes, M.; Knudsen, Morten

    1995-01-01

    A model adaptation method for estimating the electrical parameters of an induction motor at stand-still is described.......A model adaptation method for estimating the electrical parameters of an induction motor at stand-still is described....

  11. Formation of two-dimensional nonspreading atomic wave packets in the field of two standing light waves

    NARCIS (Netherlands)

    Efremov, MA; Petropavlovsky, SV; Fedorov, MV; Schleich, WP; Yakovlev, VP

    2005-01-01

    The formation of two-dimensional nonspreading atomic wave packets produced in the interaction of a beam of two-level atoms with two standing light waves polarised in the same plane is considered. The mechanism providing a dispersionless particle dynamics is the balance of two processes: a rapid deca

  12. Suppression of Spiral Waves by Voltage Clamp Techniques in a Conductance-Based Cardiac Tissue Model

    Institute of Scientific and Technical Information of China (English)

    YU Lian-Chun; MA Jun; ZHANG Guo-Yong; CHEN Yong

    2008-01-01

    A new control method is proposed to control the spatio-temporal dynamics in excitable media, which is described by the Morris-Lecar cells model. It is confirmed that successful suppression of spiral waves can be obtained by spatially clamping the membrane voltage of the excitable cells. The low voltage clamping induces breakup of spiral waves and the fragments are soon absorbed by low voltage obstacles, whereas the high voltage clamping generates travel waves that annihilate spiral waves through collision with them. However, each method has its shortcomings. Furthermore, a two-step method that combines both low and high voltage clamp techniques is then presented as a possible way of out this predicament.

  13. Modeling stick-slip-separation dynamics in a bimodal standing wave ultrasonic motor

    Science.gov (United States)

    Li, Xiang; Yao, Zhiyuan; Lv, Qibao; Liu, Zhen

    2016-11-01

    Ultrasonic motor (USM) is an electromechanical coupling system with ultrasonic vibration, which is driven by the frictional contact force between the stator (vibrating body) and the rotor/slider (driven body). Stick-slip motion can occur at the contact interface when USM is operating, which may affect the performance of the motor. This paper develops a physically-based model to investigate the complex stick-slip-separation dynamics in a bimodal standing wave ultrasonic motor. The model includes both friction nonlinearity and intermittent separation nonlinearity of the system. Utilizing Hamilton's principle and assumed mode method, the dynamic equations of the stator are deduced. Based on the dynamics of the stator and the slider, sticking force during the stick phase is derived, which is used to examine the stick-to-slip transition. Furthermore, the stick-slip-separation kinematics is analyzed by establishing analytical criteria that predict the transition between stick, slip and separation of the interface. Stick-slip-separation motion is observed in the resulting model, and numerical simulations are performed to study the influence of parameters on the range of possible motions. Results show that stick-slip motion can occur with greater preload and smaller voltage amplitude. Furthermore, a dimensionless parameter is proposed to predict the occurrence of stick-slip versus slip-separation motions, and its role in designing ultrasonic motors is discussed. It is shown that slip-separation motion is favorable for the slider velocity.

  14. The Shadow Knows: Inferring the Density Distribution of a Nonuniform Medium from Its Standing Wave Pattern

    Science.gov (United States)

    Binder, Philippe; Cunnyngham, Ian

    2012-01-01

    In a recent note in this journal, Gluck presents a beautiful demonstration of the standing wave generated by a strip of material with linearly varying width (a trapezoid). As expected, the resulting wave envelope (and its shadow) showed a varying wavelength--smaller as the strip width gets larger.

  15. The structure of standing Alfvén waves in a dipole magnetosphere with moving plasma

    Directory of Open Access Journals (Sweden)

    D. A. Kozlov

    2006-03-01

    Full Text Available The structure and spectrum of standing Alfvén waves were theoretically investigated in a dipole magnetosphere with moving plasma. Plasma motion was simulated with its azimuthal rotation. The model's scope allowed for describing a transition from the inner plasmasphere at rest to the outer magnetosphere with convecting plasma and, through the magnetopause, to the moving plasma of the solar wind. Solutions were found to equations describing longitudinal and transverse (those formed, respectively, along field lines and across magnetic shells structures of standing Alfvén waves with high azimuthal wave numbers m>>1. Spectra were constructed for a number of first harmonics of poloidal and toroidal standing Alfvén waves inside the magnetosphere. For charged particles with velocities greatly exceeding the velocity of the background plasma, an effective parallel wave component of the electric field appears in the region occupied by such waves. This results in structured high-energy-particle flows and in the appearance of multiband aurorae. The transverse structure of the standing Alfvén waves' basic harmonic was shown to be analogous to the structure of a discrete auroral arc.

  16. Overdetermined Shooting Methods for Computing Standing Water Waves with Spectral Accuracy

    CERN Document Server

    Wilkening, Jon

    2012-01-01

    A high-performance shooting algorithm is developed to compute time-periodic solutions of the free-surface Euler equations with spectral accuracy in double and quadruple precision. The method is used to study resonance and its effect on standing water waves. We identify new nucleation mechanisms in which isolated large-amplitude solutions, and closed loops of such solutions, suddenly exist for depths below a critical threshold. We also study degenerate and secondary bifurcations related to Wilton's ripples in the traveling case, and explore the breakdown of self-similarity at the crests of extreme standing waves. In shallow water, we find that standing waves take the form of counter-propagating solitary waves that repeatedly collide quasi-elastically. In deep water with surface tension, we find that standing waves resemble counter-propagating depression waves. We also discuss existence and non-uniqueness of solutions, and smooth versus erratic dependence of Fourier modes on wave amplitude and fluid depth. In t...

  17. Standing Slow MHD Waves in Radiatively Cooling Coronal Loops

    CERN Document Server

    Al-Ghafri, Khalil Salim

    2015-01-01

    The standing slow magneto-acoustic oscillations in cooling coronal loops are investigated. There are two damping mechanisms which are considered to generate the standing acoustic modes in coronal magnetic loops namely thermal conduction and radiation. The background temperature is assumed to change temporally due to optically thin radiation. In particular, the background plasma is assumed to be radiatively cooling. The effects of cooling on longitudinal slow MHD modes is analytically evaluated by choosing a simple form of radiative function that ensures the temperature evolution of the background plasma due to radiation coincides with the observed cooling profile of coronal loops. The assumption of low-beta plasma leads to neglect the magnetic field perturbation and eventually reduces the MHD equations to a 1D system modelling longitudinal MHD oscillations in a cooling coronal loop. The cooling is assumed to occur on a characteristic time scale much larger than the oscillation period that subsequently enables...

  18. Influence of standing surface waves on thermocapillary convection stability and crystal growth in weightlessness

    Science.gov (United States)

    Feonychev, A. I.

    Numerical investigation of thermocapillary flows and crystal growth by the floating zone method had been carried out in the case what free fluid surface oscillates in the form of standing wave by vibration. Two sorts of standing waves were considered. First, it is inertia-capillary standing waves due to vibration motion of fluid column as unit. These waves had been discovered under numerical investigation of problem /1/. Analytical model and the characteristic properties of these waves are described in /2/. Secondly, usual capillary waves generated by vibration of growing crystal were also considered. The effects of these surface waves on fluid flow and heat and mass transfer in process of crystal growth had been investigated over the wide ranges of dimensionless parameters for the Prandtl number is less than 1. The Marangoni number was varied from 140 to 2500, the range of cyclic frequency was between 200 and 76000. Transition from laminar thermocapillary convection to regime of flow with high oscillations (turbulent convection) happens very sharply when dimensionless amplitude (scale for linear dimensions is radius of fluid column) of standing wave reached 0.01112/n, where n is number of standing wave periods are along the length of fluid zone. If configuration of standing wave correlates with thermocapillary flow pattern two specific regimes of flow had been discovered. Flow with small oscillations is located in the range of standing wave amplitude between 0.0028 and 0.00418. In this area, radial macrosegregation of dopant is lowered by the factor of 3-6 depending on the Marangoni number. Next is an area with practically stable flow, in particular is identical to laminar flow without vibration. This area ends very sharply in the boundary of turbulent flow. All the mentioned boundaries are independent of the Marangoni number and frequency of oscillation of standing wave. For oscillatory thermocapillary convection (the Marangoni number is more than 2000

  19. Adiabatic asymmetric scattering of atoms in the field of a standing wave

    CERN Document Server

    Hakobyan, M V; Ishkhanyan, A M

    2015-01-01

    A model of the asymmetric coherent scattering process (caused by initial atomic wave-packet splitting in the momentum space) taking place at the large detuning and adiabatic course of interaction for an effective two-state system interacting with a standing wave of laser radiation is discussed. We show that the same form of initial wave-packet splitting may lead to different, in general, diffraction patterns for opposite, adiabatic and resonant, regimes of the standing-wave scattering. We show that the scattering of the Gaussian wave packet in the adiabatic case presents refraction (a limiting form of the asymmetric scattering) in contrast to the bi-refringence (the limiting case of the high-order narrowed scattering) occurring in the resonant scattering.

  20. Voltage amplification of thermopower waves via current crowding at high resistances in self-propagating combustion waves

    Science.gov (United States)

    Yeo, Taehan; Hwang, Hayoung; Cho, Yonghwan; Shin, Dongjoon; Choi, Wonjoon

    2015-07-01

    Combustion wave propagation in micro/nanostructured materials generates a chemical-thermal-electrical energy conversion, which enables the creation of an unusual source of electrical energy, called a thermopower wave. In this paper, we report that high electrical resistance regimes would significantly amplify the output voltage of thermopower waves, because the current crowding creates a narrow path for charge carrier transport. We show that the structurally defective regions in the hybrid composites of chemical fuels and carbon nanotube (CNT) arrays determine both the resistance levels of the hybrid composites and the corresponding output voltage of thermopower waves. A sudden acceleration of the crowded charges would be induced by the moving reaction front of the combustion wave when the supplied driving force overcomes the potential barrier to cause charge carrier transport over the defective region. This property is investigated experimentally for the locally manipulated defective areas using diverse methods. In this study, thermopower waves in CNT-based hybrid composites are able to control the peak voltages in the range of 10-1000 mV by manipulating the resistance from 10 Ω to 100 kΩ. This controllable voltage generation from thermopower waves may enable applications using the combustion waves in micro/nanostructured materials and better understanding of the underlying physics.

  1. Acoustic clouds: standing sound waves around a black hole analogue

    CERN Document Server

    Benone, Carolina L; Herdeiro, Carlos; Radu, Eugen

    2014-01-01

    Under certain conditions sound waves in fluids experience an acoustic horizon with analogue properties to those of a black hole event horizon. In particular, a draining bathtub-like model can give rise to a rotating acoustic horizon and hence a rotating black hole (acoustic) analogue. We show that sound waves, when enclosed in a cylindrical cavity, can form stationary waves around such rotating acoustic black holes. These acoustic perturbations display similar properties to the scalar clouds that have been studied around Kerr and Kerr-Newman black holes; thus they are dubbed acoustic clouds. We make the comparison between scalar clouds around Kerr black holes and acoustic clouds around the draining bathtub explicit by studying also the properties of scalar clouds around Kerr black holes enclosed in a cavity. Acoustic clouds suggest the possibility of testing, experimentally, the existence and properties of black hole clouds, using analog models.

  2. Damage Detection on Thin-walled Structures Utilizing Laser Scanning and Standing Waves

    Energy Technology Data Exchange (ETDEWEB)

    Kang, Se Hyeok; Jeon, Jun Young; Kim, Du Hwan; Park, Gyuhae [Chonnam Nat’l Univ., Gwangju (Korea, Republic of); Kang, To; Han, Soon Woo [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2017-05-15

    This paper describes wavenumber filtering for damage detection using single-frequency standing wave excitation and laser scanning sensing. An embedded piezoelectric sensor generates ultrasonic standing waves, and the responses are measured using a laser Doppler vibrometer and mirror tilting device. After scanning, newly developed damage detection techniques based on wavenumber filtering are applied to the full standing wave field. To demonstrate the performance of the proposed techniques, several experiments were performed on composite plates with delamination and aluminum plates with corrosion damage. The results demonstrated that the developed techniques could be applied to various structures to localize the damage, with the potential to improve the damage detection capability at a high interrogation speed.

  3. Controlled high-energy ion acceleration with intense chirped standing waves

    Science.gov (United States)

    Mackenroth, Felix; Gonoskov, Arkady; Marklund, Mattias

    2016-10-01

    We present the latest results of the recently proposed ion acceleration mechanism ``chirped standing wave acceleration''. This mechanism is based on locking the electrons of a thin plasma layer to the moving nodes of a standing wave formed by a chirped laser pulse reflected from a mirror behind the thin layer. The resulting longitudinal charge separation field between the displaced electrons and the residual ions then accelerates the latter. Since the plasma layer is stabilized by the standing wave, the formation of plasma instabilities is suppressed. Furthermore, the experimentally accessible laser chirp provides a versatile tool for manipulating the resulting ion beam in terms of maximum particle energy, particle number and spectral distribution. Through this scheme, proton beams, with energy spectra peaked around 100 MeV, were shown to be feasible for pulse energies at the level of 10 J. Wallenberg Foundation within the Grant ''Plasma based compact ion sources'' (PLIONA).

  4. Quantum Entropic Dynamics of a Trapped Ion in a Standing Wave

    Institute of Scientific and Technical Information of China (English)

    FANG Mao-Fa; ZHOU Peng; S. Swain

    2000-01-01

    By performing a unitary transformation, we transform the Hamiltonian of the trapped ion in any position of standing wave to that of the normal Jaynes-Cummings model in ionic bare basis and we obtain a general evolution operator of the trapped ion system. We study the quantum entropic dynamics of the phonons and trapped ion.Our results show that, when the trapped ion is located at the node of standing wave, the quantum entropic dynamics of phonons and trapped ion are the same as the one of the field in the Jaynes-Cummings model.When the trapped ion deviatesfrom the node of standing wave, the entropies of the phonons and ion keep their maximum value except at the initial stage, and the phonons and trapped ion become extremely entangled.

  5. High-current Standing Wave Linac With Gyrocon Power Source

    CERN Document Server

    Karliner, M M; Makarov, I G; Nezhevenko, O A; Ostreiko, G N; Persov, B Z; Serdobintsev, G V

    2004-01-01

    A gyrocon together with high-voltage 1.5 MeV accelerator ELIT-3A represents a power generator at 430 MHz serving for linear electron accelerator pulse driving. The facility description and results of calorimetric measurements of ELIT-3A electron beam power and accelerated beam at the end of accelerator are presented in the paper. 2.2 amps of pulsed current have been obtained at electron energy of 20 MeV. The achieved energy conversion efficiency is about 55%.

  6. Sand Bed Morphodynamics under Standing Waves and Vegetated Conditions

    Science.gov (United States)

    Landry, B. J.; Garcia, M. H.

    2010-12-01

    Littoral processes such as sediment transport, wave attenuation, and boundary layer development are governed by the presence of bathymetric features, which include large-scale sand bars upon which smaller-scale sand ripples are superimposed, as well as the presence of submarine vegetation. Numerous studies on sand ripples and bars have aided to elucidate the dynamics in oscillatory flows; however, the effect of vegetation on the system is less understood. Recent laboratory studies have focused on quantifying wave attenuation by emergent vegetation as a natural method to mitigate storm surges. The emergent vegetation, while promising for coastal protection, alters sediment transport rates directly by the physical presence of the plants near the bed and indirectly from reduction in near-bed shear stresses due to attenuated wave energy. The experimental work herein focuses on the area near the deeply submerged vegetated canopy limit (current work has a ratio of mean still water depth to plant height, H/h, = 7.9) to minimize the effect on the surface waves and discern the direct impact vegetation has on sand bed morphodynamics. Experiments were conducted in the large wave tank (49-m long by 1.83-m wide by 1.22-m deep) in the Ven Te Chow Hydrosystems Laboratory at the University of Illinois in which a high reflection wave forcing was used over a uniform sand bed with a 0.25-mm median sediment diameter in which staggered and uniform arrangements of idealized vegetation (i.e., 6.35-mm diameter rigid wooden cylinders) were positioned along the bed (e.g., at predetermined sand bar troughs and over an entire sand bar). The resulting bathymetric evolution from the vegetated case experiments were compared to the base case of no vegetation using two optical methods: a high-resolution laser displacement sensor for three-dimensional surveys and digitized profiles via high-definition panoramic images of the entire test section. The experimental findings illustrate the profound

  7. Standing-wave excited soft x-ray photoemission microscopy: application to Co microdot magnetic arrays

    Energy Technology Data Exchange (ETDEWEB)

    Gray, Alexander; Kronast, Florian; Papp, Christian; Yang, See-Hun; Cramm, Stefan; Krug, Ingo P.; Salmassi, Farhad; Gullikson, Eric M.; Hilken, Dawn L.; Anderson, Erik H.; Fischer, Peter; Durr, Hermann A.; Schneider, Claus M.; Fadley, Charles S.

    2010-10-29

    We demonstrate the addition of depth resolution to the usual two-dimensional images in photoelectron emission microscopy (PEEM), with application to a square array of circular magnetic Co microdots. The method is based on excitation with soft x-ray standing-waves generated by Bragg reflection from a multilayer mirror substrate. Standing wave is moved vertically through sample simply by varying the photon energy around the Bragg condition. Depth-resolved PEEM images were obtained for all of the observed elements. Photoemission intensities as functions of photon energy were compared to x-ray optical calculations in order to quantitatively derive the depth-resolved film structure of the sample.

  8. Analysis of Nanometer Structure for Chromium Atoms in Gauss Standing Laser Wave

    Institute of Scientific and Technical Information of China (English)

    ZHANG Wen-Tao; ZHU Bao-Hua; XIONG Xian-Ming

    2010-01-01

    @@ The equation of motion of two-level chromium atoms in Gauss standing laser wave is discussed and the distribution of chromium atoms is given under different transverse velocity conditions.The results show that the focusing position of atoms will be affected by the transverse velocity of atoms.Based on the four-order Runge-Kutta method,the locus of chromium atoms in Gauss standing laser wave is simulated.The three-dimensional characteristics of nanometer structures are stimulated under perfect and emanative conditions.

  9. Position-dependent dynamics of a trapped ion in a standing wave laser

    Institute of Scientific and Technical Information of China (English)

    方卯发

    2002-01-01

    We have investigated the position-dependent dynamics of a trapped ion in a standing wave laser by transforming it to the Jaynes-Cummings-type system under the Lamb-Dicke limit. A variety of novel phenomena are exhibited,e.g. periodic collapse and revival features and long-time scaled revivals of the ionic inversion, depending on its position in the standing wave. Our result provides a way of producing a system equivalent to the two-photon Jaynes-Cummings model in the trapped ion system, with its exact periodicities.

  10. A Scanned Perturbation Technique For Imaging Electromagnetic Standing Wave Patterns of Microwave Cavities

    CERN Document Server

    Gokirmak, A; Bridgewater, A; Anlage, S M; Gokirmak, Ali; Wu, Dong-Ho; Anlage, Steven M.

    1998-01-01

    We have developed a method to measure the electric field standing wave distributions in a microwave resonator using a scanned perturbation technique. Fast and reliable solutions to the Helmholtz equation (and to the Schrodinger equation for two dimensional systems) with arbitrarily-shaped boundaries are obtained. We use a pin perturbation to image primarily the microwave electric field amplitude, and we demonstrate the ability to image broken time-reversal symmetry standing wave patterns produced with a magnetized ferrite in the cavity. The whole cavity, including areas very close to the walls, can be imaged using this technique with high spatial resolution over a broad range of frequencies.

  11. Standing torsional waves in a fully saturated, porous, circular cylinder

    CERN Document Server

    Solorza, S; 10.1111/j.1365-246X.2004.02198.x

    2004-01-01

    For dynamic measurement of the elastic moduli of a porous material saturated with viscous fluid using the resonance-bar technique, one also observes attenuation. In this article we have carried out the solution of the boundary-value problem associated with standing torsional oscillations of a finite, poroelastic, circular cylinder cast in the framework of volume-averaged theory of poroelasticity. Analysing this solution by eigenvalue perturbation approach we are able to develop expressions for torsional resonance and temporal attenuation frequencies in which the dependence upon the material properties are transparent. It shows how the attenuation is controlled by the permeability and the fluid properties, and how the resonance frequency drops over its value for the dry solid-frame due to the drag effect of fluid mass. Based upon this work we have a firm basis to determine solid-frame shear modulus, permeability, and tortuosity factor from torsional oscillation experiments.

  12. On standing sausage waves in photospheric magnetic waveguides

    CERN Document Server

    Dorotovic, I; Freij, N; Karlovsky, V; Marquez, I

    2012-01-01

    By focusing on the oscillations of the cross-sectional area and the intensity of magnetic waveguides located in the lower solar atmosphere, we aim to detect and identify magnetohydrodynamic (MHD) sausage waves. Capturing several series of high-resolution images of pores and sunspots and employing wavelet analysis in conjunction with empirical mode decomposition (EMD) makes the MHD wave analysis possible. For this paper, two sunspots and one pore (with a light bridge) were chosen as representative examples of MHD waveguides in the lower solar atmosphere. The sunspots and pore display a range of periods from 4 to 65 minutes. The sunspots support longer periods than the pore - generally enabling a doubling or quadrupling of the maximum pore oscillatory period. All of these structures display area oscillations indicative of MHD sausage modes and in-phase behaviour between the area and intensity, presenting mounting evidence for the presence of the slow sausage mode within these waveguides. The presence of fast an...

  13. Homoclinic standing waves in focussing DNLS equations --Variational approach via constrained energy maximization

    CERN Document Server

    Herrmann, Michael

    2010-01-01

    We study focussing discrete nonlinear Schr\\"{o}dinger equations and present a new variational existence proof for homoclinic standing waves (bright solitons). Our approach relies on the constrained maximization of an energy functional and provides the existence of two one-parameter families of waves with unimodal and even profile function for a wide class of nonlinearities. Finally, we illustrate our results by numerical simulations.

  14. Standing Sound Waves in a tube: Approach analysis \\& sugestions

    CERN Document Server

    Vieira, L P; Lara, V O M

    2013-01-01

    In this paper we attempt to present some questions with respect to the approach used in some brazilian mid-level textbooks on the topic of stationary sound waves in tubes. In addition to ranking the textbooks within a set of criteria, we also present some suggestions for further discussions of this topic. We suggest the use of gifs and animations and the use of two experiments that allow you to view the profiles of variation of pressure and air displacement for the harmonic modes of vibration.

  15. Model independent X-ray standing wave analysis of periodic multilayer structures

    NARCIS (Netherlands)

    Yakunin, S.N.; Makhotkin, I.A.; Chuev, M.A.; Pashaev, E.M.; Zoethout, E.; Louis, E.; Kruijs, van de R.W.E.; Seregin, S.Y.; Subbotin, I.A.; Novikov, D.; Bijkerk, F.; Kovalchuk, M.V.

    2014-01-01

    We present a model independent approach for the reconstruction of the atomic concentration profile in a nanoscale layered structure, as measured using the X-ray fluorescence yield modulated by an X-ray standing wave (XSW). The approach is based on the direct regularized solution of the system of lin

  16. Model independent X-ray standing wave analysis of periodic multilayer structures

    NARCIS (Netherlands)

    Yakunin, S. N.; Makhotkin, I. A.; van de Kruijs, R. W. E.; Chuev, M. A.; Pashaev, E.M.; Zoethout, E.; E. Louis,; Seregin, Yu; Subbotin, I.A.; Novikov, D. V.; F. Bijkerk,; Kovalchuk, M. V.

    2014-01-01

    We present a model independent approach for the analysis of X-ray fluorescence yield modulated by an X-ray standing wave (XSW), that allow a fast reconstruction of the atomic distribution function inside a sample without fitting procedure. The approach is based on the direct regularized solution of

  17. Particle motion of accelerated electrons in standing-wave RF structures

    Science.gov (United States)

    Hammen, A. F. J.; Corstens, J. M.; Botman, J. I. M.; Hagedoorn, H. L.; Theuws, W. H. C.

    1999-05-01

    A Hamiltonian theory has been formulated, which is used to calculate accelerated particle motion in standing-wave RF structures. In particular, these calculations have been applied to the Eindhoven racetrack microtron accelerating cavity. The calculations are in excellent agreement with simulations performed by particle-tracking codes.

  18. Dynamics of spontaneous radiation of atoms scattered by a resonance standing light wave

    NARCIS (Netherlands)

    Fedorov, MV; Efremov, MA; Yakovlev, VP; Schleich, WP

    2003-01-01

    The scattering of atoms by a resonance standing light wave is considered under conditions when the lower of two resonance levels is metastable, while the upper level rapidly decays due to mainly spontaneous radiative transitions to the nonresonance levels of an atom. The diffraction scattering regim

  19. Vibration of a single microcapsule with a hard plastic shell in an acoustic standing wave field.

    Science.gov (United States)

    Koyama, Daisuke; Kotera, Hironori; Kitazawa, Natsuko; Yoshida, Kenji; Nakamura, Kentaro; Watanabe, Yoshiaki

    2011-04-01

    Observation techniques for measuring the small vibration of a single microcapsule of tens of nanometers in an acoustic standing wave field are discussed. First, simultaneous optical observation of a microbubble vibration by two methods is investigated, using a high-speed video camera, which permits two-dimensional observation of the bubble vibration, and a laser Doppler vibrometer (LDV), which can observe small bubble vibration amplitudes at high frequency. Bubbles of tens of micrometers size were trapped at the antinode of an acoustic standing wave generated in an observational cell. Bubble vibration at 27 kHz could be observed and the experimental results for the two methods showed good agreement. The radial vibration of microcapsules with a hard plastic shell was observed using the LDV and the measurement of the capsule vibration with radial oscillation amplitude of tens of nanometers was successful. The acoustic radiation force acting on microcapsules in the acoustic standing wave was measured from the trapped position of the standing wave and the radial oscillation amplitude of the capsules was estimated from the theoretical equation of the acoustic radiation force, giving results in good agreement with the LDV measurements. The radial oscillation amplitude of a capsule was found to be proportional to the amplitude of the driving sound pressure. A larger expansion ratio was observed for capsules closer to the resonance condition under the same driving sound pressure and frequency.

  20. Standing Waves in an Elastic Spring: A Systematic Study by Video Analysis

    Science.gov (United States)

    Ventura, Daniel Rodrigues; de Carvalho, Paulo Simeão; Dias, Marco Adriano

    2017-04-01

    The word "wave" is part of the daily language of every student. However, the physical understanding of the concept demands a high level of abstract thought. In physics, waves are oscillating variations of a physical quantity that involve the transfer of energy from one point to another, without displacement of matter. A wave can be formed by an elastic deformation, a variation of pressure, changes in the intensity of electric or magnetic fields, a propagation of a temperature variation, or other disturbances. Moreover, a wave can be categorized as pulsed or periodic. Most importantly, conditions can be set such that waves interfere with one another, resulting in standing waves. These have many applications in technology, although they are not always readily identified and/or understood by all students. In this work, we use a simple setup including a low-cost constant spring, such as a Slinky, and the free software Tracker for video analysis. We show they can be very useful for the teaching of mechanical wave propagation and the analysis of harmonics in standing waves.

  1. Acoustic radiation force of high-order Bessel beam standing wave tweezers on a rigid sphere.

    Science.gov (United States)

    Mitri, F G

    2009-12-01

    Particle manipulation using the acoustic radiation force of Bessel beams is an active field of research. In a previous investigation, [F.G. Mitri, Acoustic radiation force on a sphere in standing and quasi-standing zero-order Bessel beam tweezers, Annals of Physics 323 (2008) 1604-1620] an expression for the radiation force of a zero-order Bessel beam standing wave experienced by a sphere was derived. The present work extends the analysis of the radiation force to the case of a high-order Bessel beam (HOBB) of positive order m having an angular dependence on the phase phi. The derivation for the general expression of the force is based on the formulation for the total acoustic scattering field of a HOBB by a sphere [F.G. Mitri, Acoustic scattering of a high-order Bessel beam by an elastic sphere, Annals of Physics 323 (2008) 2840-2850; F.G. Mitri, Equivalence of expressions for the acoustic scattering of a progressive high order Bessel beam by an elastic sphere, IEEE Transactions on Ultrasonics Ferroelectrics and Frequency Control 56 (2009) 1100-1103] to derive the general expression for the radiation force function YJm,st(ka,beta,m)Bessel beam standing wave incident upon a rigid sphere immersed in non-viscous water are computed. The rigid sphere calculations for YJm,st(ka,beta,m)Bessel beam standing wave (m=0). The proposed theory is of particular interest essentially due to its inherent value as a canonical problem in particle manipulation using the acoustic radiation force of a HOBB standing wave on a sphere. It may also serve as the benchmark for comparison to other solutions obtained by strictly numerical or asymptotic approaches.

  2. Ionizing potential waves and high-voltage breakdown streamers.

    Science.gov (United States)

    Albright, N. W.; Tidman, D. A.

    1972-01-01

    The structure of ionizing potential waves driven by a strong electric field in a dense gas is discussed. Negative breakdown waves are found to propagate with a velocity proportional to the electric field normal to the wavefront. This causes a curved ionizing potential wavefront to focus down into a filamentary structure, and may provide the reason why breakdown in dense gases propagates in the form of a narrow leader streamer instead of a broad wavefront.

  3. Illustrations and Supporting Texts for Sound Standing Waves of Air Columns in Pipes in Introductory Physics Textbooks

    Science.gov (United States)

    Zeng, Liang; Smith, Chris; Poelzer, G. Herold; Rodriguez, Jennifer; Corpuz, Edgar; Yanev, George

    2014-01-01

    In our pilot studies, we found that many introductory physics textbook illustrations with supporting text for sound standing waves of air columns in open-open, open-closed, and closed-closed pipes inhibit student understanding of sound standing wave phenomena due to student misunderstanding of how air molecules move within these pipes. Based on…

  4. Illustrations and Supporting Texts for Sound Standing Waves of Air Columns in Pipes in Introductory Physics Textbooks

    Science.gov (United States)

    Zeng, Liang; Smith, Chris; Poelzer, G. Herold; Rodriguez, Jennifer; Corpuz, Edgar; Yanev, George

    2014-01-01

    In our pilot studies, we found that many introductory physics textbook illustrations with supporting text for sound standing waves of air columns in open-open, open-closed, and closed-closed pipes inhibit student understanding of sound standing wave phenomena due to student misunderstanding of how air molecules move within these pipes. Based on…

  5. Velocity selective trapping of atoms in a frequency-modulated standing laser wave

    CERN Document Server

    Argonov, V Yu

    2013-01-01

    The wave function of a moderately cold atom in a stationary near-resonant standing light wave delocalizes very fast due to wave packet splitting. However, we show that frequency modulation of the field may suppress packet splitting for some atoms having specific velocities in a narrow range. These atoms remain localized in a small space for a long time. We propose that in a real experiment with cold atomic gas this effect may decrease the velocity distribution of atoms (the field traps the atoms with such specific velocities while all other atoms leave the field)

  6. Studies of dissipative standing shock waves around black holes

    CERN Document Server

    Das, Santabrata; Mondal, Soumen

    2009-01-01

    We investigate the dynamical structure of advective accretion flow around stationary as well as rotating black holes. For a suitable choice of input parameters, such as, accretion rate ($\\dot {\\cal M}$) and angular momentum ($\\lambda$), global accretion solution may include a shock wave. The post shock flow is located at few tens of Schwarzchild radius and it is generally very hot and dense. This successfully mimics the so called Compton cloud which is believed to be responsible for emitting hard radiations. Due to the radiative loss, a significant energy from the accreting matter is removed and the shock moves forward towards the black hole in order to maintain the pressure balance across it. We identify the effective area of the parameter space ($\\dot {\\cal M} - \\lambda$) which allows accretion flows to have some energy dissipation at the shock $(\\Delta {\\cal E})$. As the dissipation is increased, the parameter space is reduced and finally disappears when the dissipation is reached its critical value. The d...

  7. Standing waves in a partitioned tube with passive membrane

    Science.gov (United States)

    Amundsen, David E.; Cox, Edward A.; Mortell, Michael P.

    2008-11-01

    The propagation of waves within a tube containing disparate gases separated by a passive membrane is modeled and analyzed in the limit of weak dissipation and applied forcing. This provides a simple setting in which to study the nonlinear interactions within and between each gas and provides a paradigm for other similar physical systems such as laminated elastic materials. The associated resonant frequencies are found in terms of a linear functional equation involving a non-trivial combination of the separate natural frequencies. As expected, in the limit that the gases have the same material properties, the modes become commensurate and the model reduces to that of the classical shock tube. However sufficiently away from this limit it is seen that this structure is lost and smooth single mode resonant solutions arise. Using a perturbative approach these solutions are approximated and compared to numerical solutions of the full system. The transition between smooth and discontinuous solutions is also studied both numerically and analytically, based on a dimensionless parameter associated with the relative material difference.

  8. The operation of stochastic heating mechanisms in an electromagnetic standing wave configuration

    Energy Technology Data Exchange (ETDEWEB)

    Gell, Y.; Nakach, R.

    1991-10-01

    The possibility of the operation of stochastic heating mechanisms of charged particles in a configuration consisting of a left-handed circularly polarized standing electromagnetic wave and a uniform magnetic field, has been studied numerically and theoretically. It is found that such a configuration induces stochasticity, the threshold of which is dependent on two independent parameters, determined by the frequency and the amplitude of the wave and the strength of the magnetic field. From the theoretical analysis, it emerges that the origin of onset of large scale stochasticity is the destabilization of fixed points associated with an equation describing the motion of the particles in an electrostatic-type potential having standing wave characteristics. The comparison of the theoretical predictions with the numerical results is found to be quite satisfactory. Possible applications to realistic plasmas have been discussed.

  9. 驻波演示实验研究%The Demonstrating Experiment of Standing Waves

    Institute of Scientific and Technical Information of China (English)

    柳建国; 陈钺

    2015-01-01

    详析驻波演示实验,分析驻波稳定出现时,因音叉臂的振幅(即入射波源的振幅)恒为A0,故弦线长必为:L=nλ±λ(n=1,2,3,…),以校正一些资料中取L=nλ(n=1,2,3,…)之误.2122%This paper presents a detailed analysis of the standing waves demonstrating experiment. Through investigating that when the standing waves stability appears, the amplitude of the tuning fork arm (i.e., the amplitude of Incident wave source) identically equals toA0, so the length of the string must be L=nλ±λ (n=1, 2, 3,…), this paper corrects the error that some 2 12 documents make taking L=nλ (n=1, 2, 3,…).

  10. Stability of standing spin wave in permalloy thin film studied by anisotropic magnetoresistance effect

    Energy Technology Data Exchange (ETDEWEB)

    Yamanoi, K.; Yokotani, Y. [Department of Physics, Kyushu University, 6-10-1 Hakozaki, Fukuoka 812-8581 (Japan); Cui, X. [Graduate School of Information Science and Electrical Engineering, Kyushu University, 744 Motooka, Fukuoka 819-0395 (Japan); Yakata, S. [Department of Information Electronics, Fukuoka Institute of Technology, 3-30-1 Wajiro-higashi, Higashi-ku, Fukuoka 811-0295 (Japan); Kimura, T., E-mail: t-kimu@phys.kyushu-u.ac.jp [Department of Physics, Kyushu University, 6-10-1 Hakozaki, Fukuoka 812-8581 (Japan); Research Center for Quantum Nano-Spin Sciences, Kyushu University, 6-10-1 Hakozaki, Fukuoka 812-8581 (Japan)

    2015-12-21

    We have investigated the stability for the resonant spin precession under the strong microwave magnetic field by a specially developed detection method using the anisotropic magnetoresistance effect. The electrically separated excitation and detection circuits enable us to investigate the influence of the heating effect and the nonuniform spin dynamics independently. The large detecting current is found to induce the field shift of the resonant spectra because of the Joule heating. From the microwave power dependence, we found that the linear response regime for the standing spin wave is larger than that for the ferromagnetic resonance. This robust characteristic of the standing spin wave is an important advantage for the high power operation of the spin-wave device.

  11. A study on the Antarctic circumpolar wave mode-A coexistence system of standing and traveling wave

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    The Antarctic circumpolar wave (ACW) has become a focus of the air-sea coupled Southern Ocean study since 1996, when it was discovered as an air-sea coupled interannual signal propagating eastward in the region of the Antarctic Circumpolar Current (ACC). In order to analyze the mechanism of discontinuity along the latitudinal propagation, a new idea that ACW is a system with a traveling wave in the Southern Pacific and Atlantic Ocean and with a concurrent standing wave in the southern Indian Ocean is proposed in this paper. Based on the ideal wave principle, the average wave parameters of ACW is achieved using a non-linear approximation method, by which we find that the standing part and the traveling part possess similar radius frequency, proving their belonging to an integral system. We also give the latitudinal distribution of wave speed with which we could tell the reason for steady propagation during the same period. The spatial distribution of the propagation reveals complex process with variant spatial and temporal scales-The ENSO scale oscillation greatly impacts on the traveling process, while the result at the south of Australia indicates little connection between the Indian Ocean and the Pacific, which may be blocked by the vibration at the west of the Pacific. The advective effect of ACC on the propagation process should be examined clearly through dynamical method.

  12. Conjunction of standing wave and resonance in asymmetric nanowires: a mechanism for thermal rectification and remote energy accumulation.

    Science.gov (United States)

    Liu, Yue-Yang; Zhou, Wu-Xing; Chen, Ke-Qiu

    2015-12-02

    As an important way to control and manage heat transport, thermal rectification has become an elementary issue in the field of phononics and plays a key role in the designing of thermal devices. Here we investigate systematically the standing wave and the accompanying resonance process in asymmetric nanowires to understand the standing wave itself and its great effect on thermal rectification. Results show that the standing wave is sensitive to both the structural and thermal properties of the material, and its great effect on enhancing the thermal rectification is realized not only by the energy-localization nature of the standing wave, but also by the resonance-caused large amplitude and high energy of the standing wave.

  13. Currents induced by vertical varied radiation stress in standing waves and evolution of the bed composed of fine sediments

    Institute of Scientific and Technical Information of China (English)

    Jing-Xin ZHANG; Hua LIU

    2009-01-01

    This paper extends the conventional concept of radiation stress (Longuet-Higgins and Stewart, 1964)in progressive water waves to standing waves, so that its vertical profile could be defined and calculated in a new technical way. The hydrodynamic numerical model being coupled with the vertically varying radiation stress in standing waves is used to simulate the currents being induced by standing waves in the vertical section. Numerical modeling of suspended sediment transport is then carried out to simulate the evolution of the bed composed of fine sediments by the currents. The scour and deposition patterns simulated are in qualitative agreement with prior laboratory and field observations.

  14. Universal Voltage Conveyor and Current Conveyor in Fast Full-Wave Rectifier

    Directory of Open Access Journals (Sweden)

    Josef Burian

    2012-12-01

    Full Text Available This paper deals about the design of a fast voltage-mode full-wave rectifier, where universal voltage conveyor and second-generation current conveyor are used as active elements. Thanks to the active elements, the input and output impedance of the non-linear circuit is infinitely high respectively zero in theory. For the rectification only two diodes and three resistors are required as passive elements. The performance of the circuit is shown on experimental measurement results showing the dynamic range, time response, frequency dependent DC transient value and RMS error for different values of input voltage amplitudes.

  15. Coherent cooling of atoms in a frequency-modulated standing laser wave: wave function and stochastic trajectory approaches

    CERN Document Server

    Argonov, Victor

    2013-01-01

    The wave function of a moderately cold atom in a stationary near-resonant standing light wave delocalizes very fast due to wave packet splitting. However, we show that frequency modulation of the field may suppress packet splitting for some atoms having specific velocities in a narrow range. These atoms remain localized in a small space for a long time. We demonstrate and explain this effect numerically and analytically. Also we demonstrate that modulated field can not only trap, but also cool the atoms. We perform a numerical experiment with a large atomic ensebmble having wide initial velocity and energy distribution. During the experiment, most of atoms leave the wave while trapped atoms have narrow energy distribution

  16. Axial acoustic radiation force on rigid oblate and prolate spheroids in Bessel vortex beams of progressive, standing and quasi-standing waves.

    Science.gov (United States)

    Mitri, F G

    2017-02-01

    The analysis using the partial-wave series expansion (PWSE) method in spherical coordinates is extended to evaluate the acoustic radiation force experienced by rigid oblate and prolate spheroids centered on the axis of wave propagation of high-order Bessel vortex beams composed of progressive, standing and quasi-standing waves, respectively. A coupled system of linear equations is derived after applying the Neumann boundary condition for an immovable surface in a non-viscous fluid, and solved numerically by matrix inversion after performing a single numerical integration procedure. The system of linear equations depends on the partial-wave index n and the order of the Bessel vortex beam m using truncated but converging PWSEs in the least-squares sense. Numerical results for the radiation force function, which is the radiation force per unit energy density and unit cross-sectional surface, are computed with particular emphasis on the amplitude ratio describing the transition from the progressive to the pure standing waves cases, the aspect ratio (i.e., the ratio of the major axis over the minor axis of the spheroid), the half-cone angle and order of the Bessel vortex beam, as well as the dimensionless size parameter. A generalized expression for the radiation force function is derived for cases encompassing the progressive, standing and quasi-standing waves of Bessel vortex beams. This expression can be reduced to other types of beams/waves such as the zeroth-order Bessel non-vortex beam or the infinite plane wave case by appropriate selection of the beam parameters. The results for progressive waves reveal a tractor beam behavior, characterized by the emergence of an attractive pulling force acting in opposite direction of wave propagation. Moreover, the transition to the quasi-standing and pure standing wave cases shows the acoustical tweezers behavior in dual-beam Bessel vortex beams. Applications in acoustic levitation, particle manipulation and acousto

  17. Theoretical comparison of optical traps created by standing wave and single beam

    Science.gov (United States)

    Zemánek, Pavel; Jonáš, Alexandr; Jákl, Petr; Ježek, Jan; Šerý, Mojmír.; Liška, Miroslav

    2003-05-01

    We used generalised Lorenz-Mie scattering theory (GLMT) to compare submicron-sized particle optical trapping in a single focused beam and a standing wave. We focus especially on the study of maximal axial trapping force, minimal laser power necessary for confinement, axial trap position, and axial trap stiffness in dependency on trapped sphere radius, refractive index, and Gaussian beam waist size. In the single beam trap (SBT), the range of refractive indices which enable stable trapping depends strongly on the beam waist size (it grows with decreasing waist). On the contrary to the SBT, there are certain sphere sizes (non-trapping radii) that disable sphere confinement in standing wave trap (SWT) for arbitrary value of refractive index. For other sphere radii we show that the SWT enables confinement of high refractive index particle in wider laser beams and provides axial trap stiffness and maximal axial trapping force at least by two orders and one order bigger than in SBT, respectively.

  18. The periodic standing-wave approximation: computations in full general relativity

    CERN Document Server

    Hernandez, Napoleon

    2008-01-01

    The periodic standing wave method studies circular orbits of compact objects coupled to helically symmetric standing wave gravitational fields. From this solution an approximation is extracted for the strong field, slowly inspiralling motion of binary black holes and binary neutron stars. Previous work on this project has developed a method using a few multipoles of specially adapted coordinates well suited both to the radiation and the source regions. This method had previously been applied to linear and nonlinear scalar field models, to linearized gravity, and to a post-Minkowski approximation. Here we present the culmination of this approach: the application of the method in full general relativity. The fundamental equations had previously been developed and the challenge presented by this step is primarily a computational one which was approached with an innovative technique. The numerical results of these computations are compared with the corresponding results from linearized and post-Minkowksi computat...

  19. An experimental study on the coalescence process of binary droplets in oil under ultrasonic standing waves.

    Science.gov (United States)

    Luo, Xiaoming; Cao, Juhang; He, Limin; Wang, Hongping; Yan, Haipeng; Qin, Yahua

    2017-01-01

    The coalescence process of binary droplets in oil under ultrasonic standing waves was investigated with high-speed photography. Three motion models of binary droplets in coalescence process were illustrated: (1) slight translational oscillation; (2) sinusoidal translational oscillation; (3) migration along with acoustic streaming. To reveal the droplets coalescence mechanisms, the influence of main factors (such as acoustic intensity, droplet size, viscosity and interfacial tension, etc) on the motion and coalescence of binary droplets was studied under ultrasonic standing waves. Results indicate that the shortest coalescence time is achieved when binary droplets show sinusoidal translational oscillation. The corresponding acoustic intensity in this case is the optimum acoustic intensity. Under the optimum acoustic intensity, drop size decrease will bring about coalescence time decrease by enhancing the binary droplets oscillation. Moreover, there is an optimum interfacial tension to achieve the shortest coalescence time.

  20. Standing Slow-Mode Waves in Hot Coronal Loops: Observations, Modeling, and Coronal Seismology

    CERN Document Server

    Wang, Tongjiang

    2010-01-01

    Strongly damped Doppler shift oscillations are observed frequently associated with flarelike events in hot coronal loops. In this paper, a review of the observed properties and the theoretical modeling is presented. Statistical measurements of physical parameters (period, decay time, and amplitude) have been obtained based on a large number of events observed by SOHO/SUMER and Yohkoh/BCS. Several pieces of evidence are found to support their interpretation in terms of the fundamental standing longitudinal slow mode. The high excitation rate of these oscillations in small- or micro-flares suggest that the slow mode waves are a natural response of the coronal plasma to impulsive heating in closed magnetic structure. The strong damping and the rapid excitation of the observed waves are two major aspects of the waves that are poorly understood, and are the main subject of theoretical modeling. The slow waves are found mainly damped by thermal conduction and viscosity in hot coronal loops. The mode coupling seems ...

  1. RESONANT INTERACTION BETWEEN A PAUL-TRAPPED ION AND A STANDING WAVE LASER

    Institute of Scientific and Technical Information of China (English)

    FENG MANG; HAI WEN-HUA; ZHU XI-WEN; GAO KE-LIN; SHI LEI

    2000-01-01

    An ultracold two-level ion experiencing the standing wave of a resonant laser in a Paul trap is investigated in the Lamb-Dicke limit and weak excitation regime, with full consideration of the time-dependence of the trapping potential.The analytical forms of the wave functions of the system can be described with our approach, and the time evolution of the pseudo-energy of the system as well as the squeezing property of the quadrature components is studied in comparison with the treatment of harmonic oscillator model.

  2. Dynamics of Two-Level Trapped Ion in a Standing Wave Laser in Noncommutative Space

    Institute of Scientific and Technical Information of China (English)

    YANG Xiao-Xue; WU Ying

    2007-01-01

    We study the dynamics of a two-level trapped ion in a standing wave electromagnetic field in two-dimensional (2D) noncommutative spaces in the Lamb-Dicke regime under the rotating wave approximation. We obtain the explicit analytical expressions for the energy spectra, energy eigenstates, unitary time evolution operator, atomic inversion, and phonon number operators. The Rabi oscillations, the collapse, and revivals in the average atomic inversion and the average phonon number are explicitly shown to contain the information of the parameter of the space noncommutativity,which sheds light on proposing new schemes based on the dynamics of trappedion to test the noncommutativity.

  3. Localization of Matter Fields in the 5D Standing Wave Braneworld

    CERN Document Server

    Gogberashvili, Merab

    2012-01-01

    We investigate the localization problem of matter fields within the 5D standing wave braneworld. In this model the brane emits anisotropic waves into the bulk with different amplitudes along different spatial dimensions. We show that in the case of increasing warp factor there exist the pure gravitational localization of all kinds of quantum and classical particles on the brane. For classical particles the anisotropy of the background metric is hidden, brane fields exhibit standard Lorentz symmetry in spite of anisotropic nature of the primordial 5D metric.

  4. Thin films and buried interfaces characterization with X-ray standing waves

    Energy Technology Data Exchange (ETDEWEB)

    Lagomarsino, S. [CNR, Rome (Italy). Istituto Elettronica Stato Solido

    1996-09-01

    The X-ray standing wave techniques is a powerful, non destructive method to study interfaces at the atomic level. Its basic features are described here together with the peculiarities of its applications to epitaxial films and buried interfaces. As examples of applications, experiments carried out on Si/silicide interfaces, on GaAs/InAs/GaAs buried interfaces and on Si/Ge superlattices are shown.

  5. Acoustic radiation force on a rigid elliptical cylinder in plane (quasi)standing waves

    Energy Technology Data Exchange (ETDEWEB)

    Mitri, F. G., E-mail: F.G.Mitri@ieee.org [Chevron, Area 52 Technology–ETC, Santa Fe, New Mexico 87508 (United States)

    2015-12-07

    The acoustic radiation force on a 2D elliptical (non-circular) cylinder centered on the axis of wave propagation of plane quasi-standing and standing waves is derived, based on the partial-wave series expansion (PWSE) method in cylindrical coordinates. A non-dimensional acoustic radiation force function, which is the radiation force per unit length, per characteristic energy density and per unit cross-sectional surface of the ellipse, is defined in terms of the scattering coefficients that are determined by applying the Neumann boundary condition for an immovable surface. A system of linear equations involving a single numerical integration procedure is solved by matrix inversion. Numerical simulations showing the transition from the quasi-standing to the (equi-amplitude) standing wave behaviour are performed with particular emphasis on the aspect ratio a/b, where a and b are the ellipse semi-axes, as well as the dimensionless size parameter kb (where k is the wavenumber), without the restriction to a particular range of frequencies. It is found that at high kb values > 1, the radiation force per length with broadside incidence is larger, whereas the opposite situation occurs in the long-wavelength limit (i.e., kb < 1). The results are particularly relevant in acoustic levitation of elliptical cylinders, the acoustic stabilization of liquid columns in a host medium, acousto-fluidics devices, and other particle dynamics applications to name a few. Moreover, the formalism presented here may be effectively applied to compute the acoustic radiation force on other 2D surfaces of arbitrary shape such as super-ellipses, Chebyshev cylindrical particles, or other non-circular geometries.

  6. Variational Approach to the Orbital Stability of Standing Waves of the Gross-Pitaevskii Equation

    KAUST Repository

    Hadj Selem, Fouad

    2014-08-26

    This paper is concerned with the mathematical analysis of a masssubcritical nonlinear Schrödinger equation arising from fiber optic applications. We show the existence and symmetry of minimizers of the associated constrained variational problem. We also prove the orbital stability of such solutions referred to as standing waves and characterize the associated orbit. In the last section, we illustrate our results with few numerical simulations. © 2014 Springer Basel.

  7. Influence of standing wave phase error on super-resolution optical inspection for periodic microstructures

    Science.gov (United States)

    Kudo, R.; Usuki, S.; Takahashi, S.; Takamasu, K.

    2012-05-01

    The miniaturization of microfabricated structures such as patterned semiconductor wafers continues to advance, thereby increasing the demand for a high-speed, nondestructive and high-resolution measurement technique. We propose a novel optical inspecting method for a microfabricated structure using the standing wave illumination (SWI) shift as such a measurement technique. This method is based on a super-resolution algorithm in which the inspection system's resolution exceeds the diffraction limit by shifting the SWI. Resolution beyond the diffraction limit has previously been studied theoretically and realized experimentally. The influence of various experimental error factors needs to be investigated and calibration needs to be performed accordingly when actual applications that utilize the proposed method are constructed. These error factors include errors related to the phase, pitch and shift step size of the standing wave. Identifying the phase accurately is extremely difficult and greatly influences the resolution result. Hence, the SWI phase was focused upon as an experimental error factor. The effect of the phase difference between the actual experimental standing wave and the computationally set standing wave was investigated using a computer simulation. The periodic structure characteristic of a microfabricated structure was analyzed. The following findings were obtained as a result. The influence of an error is divided into three modes depending on the pitch of the periodic structure: (1) if the pitch is comparatively small, the influence of the error is cancelled, allowing the structure of a sample to be resolved correctly; (2) if the pitch of the structure is from 150 to 350 nm, the reconstructed solution shifts in a transverse direction corresponding to a phase gap of SWI; and (3) if it is a comparatively large pitch, then it is difficult to reconstruct the right pitch. Verification was experimentally attempted for mode (2), and the same result as

  8. Pulsed 5 MeV standing wave electron linac for radiation processing

    Science.gov (United States)

    Auditore, L.; Barnà, R. C.; de Pasquale, D.; Italiano, A.; Trifirò, A.; Trimarchi, M.

    2004-03-01

    Several modern applications of radiation processing require compact and self-contained electron accelerators. To match these requirements, a 5MeV, 1kW electron linac has been developed at the Dipartimento di Fisica (Università di Messina) and will be described in this paper. This standing wave accelerator, driven by a 3GHz, 2.5MW magnetron generator, has an autofocusing structure and will be used to study several applications of radiation processing.

  9. Effect of particle-particle interactions on the acoustic radiation force in an ultrasonic standing wave

    Energy Technology Data Exchange (ETDEWEB)

    Lipkens, Bart, E-mail: blipkens@wne.edu [Mechanical Engineering, Western New England University, Springfield, Massachusetts, 01119 (United States); Ilinskii, Yurii A., E-mail: ilinskii@gmail.com; Zabolotskaya, Evgenia A., E-mail: zheniazabolotskaya@gmail.com [Applied Research Laboratories, The University of Texas at Austin, Austin, Texas 78713–8029 (United States)

    2015-10-28

    Ultrasonic standing waves are widely used for separation applications. In MEMS applications, a half wavelength standing wave field is generated perpendicular to a laminar flow. The acoustic radiation force exerted on the particle drives the particle to the center of the MEMS channel, where concentrated particles are harvested. In macro-scale applications, the ultrasonic standing wave spans multiple wavelengths. Examples of such applications are oil/water emulsion splitting [1], and blood/lipid separation [2]. In macro-scale applications, particles are typically trapped in the standing wave, resulting in clumping or coalescence of particles/droplets. Subsequent gravitational settling results in separation of the secondary phase. An often used expression for the radiation force on a particle is that derived by Gorkov [3]. The assumptions are that the particle size is small relative to the wavelength, and therefore, only monopole and dipole scattering contributions are used to calculate the radiation force. This framework seems satisfactory for MEMS scale applications where each particle is treated separately by the standing wave, and concentrations are typically low. In macro-scale applications, particle concentration is high, and particle clumping or droplet coalescence results in particle sizes not necessarily small relative to the wavelength. Ilinskii et al. developed a framework for calculation of the acoustic radiation force valid for any size particle [4]. However, this model does not take into account particle to particle effects, which can become important as particle concentration increases. It is known that an acoustic radiation force on a particle or a droplet is determined by the local field. An acoustic radiation force expression is developed that includes the effect of particle to particle interaction. The case of two neighboring particles is considered. The approach is based on sound scattering by the particles. The acoustic field at the location of

  10. Simplified description of optical forces acting on a nanoparticle in the Gaussian standing wave

    Science.gov (United States)

    Zemánek, Pavel; Jonáš, Alexandr; Liška, Miroslav

    2002-05-01

    We study the axial force acting on dielectric spherical particles smaller than the trapping wavelength that are placed in the Gaussian standing wave. We derive analytical formulas for immersed particles with relative refractive indices close to unity and compare them with the numerical results obtained by generalized Lorenz-Mie theory (GLMT). We show that the axial optical force depends periodically on the particle size and that the equilibrium position of the particle alternates between the standing-wave antinodes and nodes. For certain particle sizes, gradient forces from the neighboring antinodes cancel each other and disable particle confinement. Using the GLMT we compare maximum axial trapping forces provided by the Gaussian standing-wave trap (SWT) and single-beam trap (SBT) as a function of particle size, refractive index, and beam waist size. We show that the SWT produces axial forces at least ten times stronger and permits particle confinement in a wider range of refractive indices and beam waists compared with those of the SBT.

  11. Standing wave plasmon modes interact in an antenna-coupled nanowire

    Science.gov (United States)

    Day, Jared; Large, Nicolas; Nordlander, Peter; Halas, Naomi

    2015-03-01

    In a standing wave optical cavity, the coupling of cavity modes, e.g. through a nonlinear medium, results in a rich variety of nonlinear dynamical phenomena, such as frequency pushing and pulling, mode-locking and pulsing, and modal instabilities. Metallic nanowires of finite length support a hierarchy of longitudinal surface plasmon modes with standing wave properties: the plasmonic analog of a Fabry-Pérot cavity. Here we show that positioning the nanowire within the gap of a plasmonic nanoantenna introduces a passive, hybridization-based coupling of the standing-wave nanowire plasmon modes with the antenna structure, mediating an interaction between the nanowire plasmon modes themselves. Frequency pushing and pulling, and the enhancement and suppression of specific plasmon modes, can be controlled and manipulated by nanoantenna position and shape. Dark-field spectroscopy, CL spectroscopy and imaging, and finite-difference time-domain calculations are performed to investigate these surface plasmon ``drift.'' Near-field coupling of nanoantennas to nanowire optical cavities shows that plasmon hybridization is a powerful strategy for controlling the radiative LDOS of nanowires, and could ultimately enable strategies for active control of emission properties in nanowire-based devices. Work funded by the Welch Foundation (C-1220, C-1222), the NSSEFF (N00244-09-1-0067), the ONR (N00014-10-1-0989), and the NSF (ECCS-1040478, CNS-0821727).

  12. Optimal Constant DC Link Voltage Operation of aWave Energy Converter

    Directory of Open Access Journals (Sweden)

    Mats Leijon

    2013-04-01

    Full Text Available This article proposes a simple and reliable damping strategy for wave powerfarm operation of small-scale point-absorber converters. The strategy is based on passiverectification onto a constant DC-link, making it very suitable for grid integration of the farm.A complete model of the system has been developed in Matlab Simulink, and uses real sitedata as input. The optimal constant DC-voltage is evaluated as a function of the significantwave height and energy period of the waves. The total energy output of the WEC is derivedfor one year of experimental site data. The energy output is compared for two cases, onewhere the optimal DC-voltage is determined and held constant at half-hour basis throughoutthe year, and one where a selected value of the DC-voltage is kept constant throughout theyear regardless of sea state.

  13. Depth-resolved soft x-ray photoelectron emission microscopy in nanostructures via standing-wave excited photoemission

    Energy Technology Data Exchange (ETDEWEB)

    Kronast, F.; Ovsyannikov, R.; Kaiser, A.; Wiemann, C.; Yang, S.-H.; Locatelli, A.; Burgler, D.E.; Schreiber, R.; Salmassi, F.; Fischer, P.; Durr, H.A.; Schneider, C.M.; Eberhardt, W.; Fadley, C.S.

    2008-11-24

    We present an extension of conventional laterally resolved soft x-ray photoelectron emission microscopy. A depth resolution along the surface normal down to a few {angstrom} can be achieved by setting up standing x-ray wave fields in a multilayer substrate. The sample is an Ag/Co/Au trilayer, whose first layer has a wedge profile, grown on a Si/MoSi2 multilayer mirror. Tuning the incident x-ray to the mirror Bragg angle we set up standing x-ray wave fields. We demonstrate the resulting depth resolution by imaging the standing wave fields as they move through the trilayer wedge structure.

  14. Dynamic magnetization switching and spin wave excitations by voltage-induced torque

    Science.gov (United States)

    Shiota, Yoichi

    2013-03-01

    The effect of electric fields on ultrathin ferromagnetic metal layer is one of the promising approaches for manipulating the spin direction with low-energy consumption, localization, and coherent behavior. Several experimental approaches to realize it have been investigated using ferromagnetic semiconductors, magnetostriction together with piezo-electric materials, multiferroic materials, and ultrathin ferromagnetic layer. In this talk, we will present a dynamic control of spins by voltage-induced torque. We used the magnetic tunnel junctions with ultrathin ferromagnetic layer, which shows voltage-induced perpendicular magnetic anisotropy change. By applying the voltage to the junction, the magnetic easy-axis in the ultrathin ferromagnetic layer changes from in-plane to out-of-plane, which causes a precession of the spins. This precession resulted in a two-way toggle switching by determining an appropriate pulse length. On the other hand, an application of rf-voltage causes an excitation of a uniform spin-wave. Since the precession of spin associates with an oscillation in the resistance of the junction, the applied rf-signal is rectified and produces a dc-voltage. From the spectrum of the dc-voltage as a function of frequency, we could estimate the voltage-induced torque. This research was supported by CREST-JST, G-COE program, and JSPS for the fellowship. Collaborators include T. Nozaki, S. Miwa, F. Bonell, N. Mizuochi, T. Shinjo, and Y. Suzuki.

  15. Flow under standing waves Part 1. Shear stress distribution, energy flux and steady streaming

    DEFF Research Database (Denmark)

    Gislason, Kjartan; Fredsøe, Jørgen; Deigaard, Rolf

    2009-01-01

    The conditions for energy flux, momentum flux and the resulting streaming velocity are analysed for standing waves formed in front of a fully reflecting wall. The exchange of energy between the outer wave motion and the near bed oscillatory boundary layer is considered, determining the horizontal...... energy flux inside and outside the boundary layer. The momentum balance, the mean shear stress and the resulting time averaged streaming velocities are determined. For a laminar bed boundary layer the analysis of the wave drift gives results similar to the original work of Longuet-Higgins from 1953....... The work is extended to turbulent bed boundary layers by application of a numerical model. The similarities and differences between laminar and turbulent flow conditions are discussed, and quantitative results for the magnitude of the mean shear stress and drift velocity are presented. Full two...

  16. Probing the polarity of ferroelectric thin films with x-ray standing waves

    Energy Technology Data Exchange (ETDEWEB)

    Bedzyk, M. J. [Department of Materials Science and Engineering and Materials Research Center, Northwestern University, Evanston, Illinois 60208 (United States); Materials Science Division, Argonne National Laboratory, Argonne, Illinois 60439 (United States); Kazimirov, A. [Department of Materials Science and Engineering and Materials Research Center, Northwestern University, Evanston, Illinois 60208 (United States); Marasco, D. L. [Department of Materials Science and Engineering and Materials Research Center, Northwestern University, Evanston, Illinois 60208 (United States); Lee, T.-L. [Department of Materials Science and Engineering and Materials Research Center, Northwestern University, Evanston, Illinois 60208 (United States); Foster, C. M. [Materials Science Division, Argonne National Laboratory, Argonne, Illinois 60439 (United States); Advanced Micro Devices, 5204 East Ben White Boulevard, Austin, Texas 78741 (United States); Bai, G.-R. [Materials Science Division, Argonne National Laboratory, Argonne, Illinois 60439 (United States); Lyman, P. F. [Department of Materials Science and Engineering and Materials Research Center, Northwestern University, Evanston, Illinois 60208 (United States); Keane, D. T. [Department of Materials Science and Engineering and Materials Research Center, Northwestern University, Evanston, Illinois 60208 (United States)

    2000-03-15

    An x-ray-diffraction method that directly senses the phase of the structure factor is demonstrated and used for determining the local polarity of thin ferroelectric films. This method is based on the excitation of an x-ray standing-wave field inside the film as a result of the interference between the strong incident x-ray wave and the weak kinematically Bragg-diffracted x-ray wave from the film. The method is used to sense the displacements of the Pb and Ti sublattices in single-crystal c-domain PbTiO{sub 3} thin films grown by metal-organic chemical-vapor deposition on SrTiO{sub 3}(001) substrates. (c) 2000 The American Physical Society.

  17. An interleaved structure for a high-voltage planar transformer for a Travelling-wave Tube

    DEFF Research Database (Denmark)

    Zhao, Bin; Wang, Gang; Hurley, William G.;

    2016-01-01

    Fully interleaved structure can significantly reduce leakage inductance in transformers, However, it is hard to apply them into high-voltage applications due to the electric insulation. In this paper, a partially interleaved structure that is suitable for high-voltage high frequency applications...... is proposed to reduce leakage inductance and the insulation’s thickness is adjusted to optimize the electric isolation. In addition, the resistance and parasitic capacitance are investigated. With this method, a planar transformer used for a Travelling-Wave Tube Amplifier (TWTA) is designed. Calculations...

  18. Influence of laser power on deposition of the chromium atomic beam in laser standing wave

    Institute of Scientific and Technical Information of China (English)

    2009-01-01

    One-dimensional deposition of collimated Cr atomic beam focused by a near-resonant Gaussian standing-laser field with wavelength of 425.55 nm is examined from particle-optics approach by using an adaptive step size,fourth-order Runge-Kutta type algorithm.The influence of laser power on deposition of atoms in laser standing wave is discussed and the simulative result shows that the FWHM of nanometer stripe is 102 nm and contrast is 2:1 with laser power equal to 3 mW,the FWHM is 1.2 nm and contrast is 32:1 with laser power equal to 16 mW,but with laser power increase,equal to 50 mW,the nonmeter structure forms the multi-crests and exacerbates.

  19. Simulation of Chromium Atom Deposition Pattern in a Gaussain Laser Standing Wave with Different Laser Power

    Institute of Scientific and Technical Information of China (English)

    ZHANG Wen-Tao; ZHU Bao-Hua

    2009-01-01

    One-dimensional deposition of a neutral chromium atomic beam focused by a near-resonant Gaussian standing-laser field is discussed by using a fourth-order Runge-Kutta type algorithm. The deposition pattern of neutral chromium atoms in a laser standing wave with different laser power is discussed and the simulation result shows that the full width at half maximum (FWHM) of a nanometer stripe is 115nm and the contrast is 2.5:1 with laser power 3.93mW; the FWHM is 0.Snm and the contrast is 27:1 with laser power 16mW, the optimal laser power; but with laser power increasing to 50mW, the nanometer structure forms multi-crests and the quality worsens quickly with increasing laser power.

  20. Influence of laser power on deposition of the chromium atomic beam in laser standing wave

    Institute of Scientific and Technical Information of China (English)

    ZHANG WenTao; ZHU BaoHua; ZHANG BaoWu; LI TongBao

    2009-01-01

    One-dimensional deposition of collimated Cr atomic beam focused by a near-resonant Gaussian standing-laser field with wavelength of 425.55 nm is examined from particle-optics approach by using an adaptive step size, fourth-order Runge-Kutta type algorithm. The influence of laser power on depo-sition of atoms in laser standing wave is discussed and the simulative result shows that the FWHM of nanometer stripe is 102 nm and contrast is 2:1 with laser power equal to 3 mW, the FWHM is 1.2 nm and contrast is 32:1 with laser power equal to 16 mW, but with laser power increase, equal to 50 mW, the nonmeter structure forms the multi-crests and exacerbates.

  1. Fabrication and Operation of Acoustofluidic Devices Supporting Bulk Acoustic Standing Waves for Sheathless Focusing of Particles

    Science.gov (United States)

    Shields, C. Wyatt; Cruz, Daniela F.; Ohiri, Korine A.; Yellen, Benjamin B.; Lopez, Gabriel P.

    2016-01-01

    Acoustophoresis refers to the displacement of suspended objects in response to directional forces from sound energy. Given that the suspended objects must be smaller than the incident wavelength of sound and the width of the fluidic channels are typically tens to hundreds of micrometers across, acoustofluidic devices typically use ultrasonic waves generated from a piezoelectric transducer pulsating at high frequencies (in the megahertz range). At characteristic frequencies that depend on the geometry of the device, it is possible to induce the formation of standing waves that can focus particles along desired fluidic streamlines within a bulk flow. Here, we describe a method for the fabrication of acoustophoretic devices from common materials and clean room equipment. We show representative results for the focusing of particles with positive or negative acoustic contrast factors, which move towards the pressure nodes or antinodes of the standing waves, respectively. These devices offer enormous practical utility for precisely positioning large numbers of microscopic entities (e.g., cells) in stationary or flowing fluids for applications ranging from cytometry to assembly. PMID:27022681

  2. Modeling of the Voltage Waves in the LHC Main Dipole Circuits

    CERN Document Server

    Ravaioli, E; Formenti, F; Steckert, J; Thiesen, H; Verweij, A

    2012-01-01

    When a fast power abort is triggered in the LHC main dipole chain, voltage transients are generated at the output of the power converter and across the energy-extraction switches. The voltage waves propagate through the chain of 154 superconducting dipoles and can have undesired effects leading to spurious triggering of the quench protection system and firing of the quench heaters. The phase velocity of the waves travelling along the chain changes due to the inhomogeneous AC behavior of the dipoles. Furthermore, complex phenomena of reflection and superposition are present in the circuit. For these reasons analytical calculations are not sufficient for properly analyzing the circuit behavior after a fast power abort. The transients following the switch-off of the power converter and the opening of the switches are analyzed by means of a complete electrical model, developed with the Cadence© suite (PSpice© based). The model comprises all the electrical components of the circuit, additional components simula...

  3. Thought waves remotely affect the performance (output voltage) of photoelectric cells

    Science.gov (United States)

    Cao, Dayong; Cao, Daqing

    2012-02-01

    In our experiments, thought waves have been shown to be capable of changing (affecting) the output voltage of photovoltaic cells located from as far away as 1-3 meters. There are no wires between brain and photoelectric cell and so it is presumed only the thought waves act on the photoelectric cell. In continual rotations, the experiments tested different solar cells, measuring devices and lamps, and the experiments were done in different labs. The first experiment was conducted on Oct 2002. Tests are ongoing. Conclusions and assumptions include: 1) the slow thought wave has the energy of space-time as defined by C1.00007: The mass, energy, space and time systemic theory- MEST. Every process releases a field effect electrical vibration which be transmitted and focussed in particular paths; 2) the thought wave has the information of the order of tester; 3) the brain (with the physical system of MEST) and consciousness (with the spirit system of the mind, consciousness, emotion and desire-MECD) can produce the information (a part of them as the Genetic code); 4) through some algorithms such as ACO Ant Colony Optimization and EA Evolutionary Algorithm (or genetic algorithm) working in RAM, human can optimize the information. This Optimizational function is the intelligence; 5) In our experiments, not only can thought waves affect the voltage of the output photoelectric signals by its energy, but they can also selectively increase or decrease those photoelectric currents through remote consciousness interface and a conscious-brain information technology.

  4. The effect of conductor loss on half-wave voltage and modulation bandwidth of electro-optic modulators

    Institute of Scientific and Technical Information of China (English)

    Zilong Liu(刘子龙); Daqing Zhu(朱大庆)

    2004-01-01

    In this paper, we theoretically deduce the expressions of half-wave voltage and 3-dB modulation bandwidth in which conductor loss is taken into account. The results suggest that it will affect the theoretical values of half-wave voltage and bandwidth as well as the optimized electrode's dimension whether considering the conductor loss or not. As an example, we present a Mach-Zehnder (MZ) type polymer waveguide amplitude modulator. The half-wave voltage increases by 1 V and the 3-dB bandwidth decreases by 30% when the conductor loss is taken into account. Besides, the effects of impedance mismatching and velocity mismatching between microwave and light wave on the half-wave voltage, and 3-dB bandwidth are discussed.

  5. Cooling and trapping of three-level atoms in a bichromatic standing wave

    Science.gov (United States)

    Pu, H.; Cai, T.; Bigelow, N. P.; Grove, T. T.; Gould, P. L.

    1995-02-01

    We show that a three-level atom in the cascade configuration can be stably trapped and cooled in one dimension by an intense bichromatic standing wave. At the two-photon resonance, rectified dipole forces result in a deep potential well which can be used to localize the atoms in space. In the vicinity of the rectified potential minimum, the spatial dependence of the dressed state energies can lead to a velocity dependence of the force which produces damping of the atomic motion. Consideration of the heating effects of momentum diffusion indicates that cooling and stable trapping at low temperatures is possible in such a bichromatic field.

  6. Two-Mode Resonator and Contact Model for Standing Wave Piezomotor

    DEFF Research Database (Denmark)

    Andersen, B.; Blanke, Mogens; Helbo, J.

    2001-01-01

    The paper presents a model for a standing wave piezoelectric motor with a two bending mode resonator. The resonator is modelled using Hamilton's principle and the Rayleigh-Ritz method. The contact is modelled using the Lagrange Multiplier method under the assumption of slip and it is showed how...... to solve the set of differential-algebraic equations. Detailed simulations show resonance frequencies as function of the piezoelement's position, tip trajectories and contact forces. The paper demonstrates that contact stiffness and stick should be included in such model to obtain physically realistic...

  7. Normal incidence X-ray standing wave analysis of thin gold films

    Science.gov (United States)

    Satterley, Christopher J.; Lovelock, Kevin R. J.; Thom, Ian; Dhanak, Vinod R.; Buck, Manfred; Jones, Robert G.

    2006-11-01

    Normal incidence X-ray standing wave (NIXSW) analysis has been successfully performed on epitaxial gold films on mica substrates using reflection from the (1 1 1) planes parallel to the surface. We show that NIXSW can be used to monitor the decrease in order within the gold film caused by annealing, and the position of sulfur within a monolayer of methyl thiolate (CH 3S-) on the surface. The Au-S layer spacing was found to be 2.54 ± 0.05 Å, in close agreement with previous work on a single crystal system.

  8. Beam dynamics studies and parametric characterization of a standing wave electron linac

    Science.gov (United States)

    Dash, R.; Mondal, J.; Sharma, A.; Mittal, K. C.

    2013-07-01

    This paper presents the results of electron beam tracking simulations for a 30 MeV standing wave electron linac at Electron Beam Centre Kharghar, Navi Mumbai, India. For the pulsed mode operation of the present linac preferential operation parameters have been determined from the results of beam dynamics studies. This electron accelerator is a general purpose facility for generation of Bremsstrahlung X-rays and neutron scattering experiments. This electron accelerator-based experimental neutron facility will be used for measurement of neutron cross-section (n,γ), (n, xn) and (n, f) reactions at different energies for various materials and material irradiation studies.

  9. Influence of Atomic Motion on a Microlaser in an Optical Standing-Wave Cavity

    Institute of Scientific and Technical Information of China (English)

    张敬涛; 冯勋立; 张文琦; 徐至展

    2002-01-01

    We study the microlaser in an optical standing-wave cavity injected with two-level atoms. The results have shown the obvious infIuence of atomic centre-of-mass motion on the microlaser, such as the photon distribution, the linewidth and the frequency shift. It was found that when the momentum of atoms is comparable to that of photons, the influence of atomic motion is dominated and the number of photons in the microlaser can be greatly enhanced, owing to part of the atomic kinetic energy being transferred to the resonator. This work provides a comparison of the related studies on the atomic motion under special assumptions.

  10. Anisotropic Inflation in a 5D Standing Wave Braneworld and Dimensional Reduction

    CERN Document Server

    Gogberashvili, Merab; Malagon-Morejon, Dagoberto; Mora-Luna, Refugio Rigel

    2012-01-01

    We investigate a cosmological solution within the framework of a 5D standing wave braneworld model generated by gravity coupled to a massless scalar phantom-like field. By obtaining a full exact solution of the model we found a novel dynamical mechanism in which the anisotropic nature of the primordial metric gives rise to i) inflation along certain spatial dimensions, and ii) deflation and a shrinking reduction of the number of spatial dimensions along other directions. This dynamical mechanism can be relevant for dimensional reduction in string and other higher dimensional theories in the attempt of getting a 4D isotropic expanding space-time.

  11. Localized auroral disturbance in the morning sector of topside ionosphere as a standing electromagnetic wave

    Energy Technology Data Exchange (ETDEWEB)

    Dubinin, E.M.; Israelevich, P.L.; Nikolaeva, N.S.; Podgornyi, I.M.; Kutiev, I.

    1985-06-01

    The fine structure and plasma properties of an auroral disturbance observed with the Intercosmos-Bulgaria-1300 satellite are analyzed. The disturbance was detected in the morning sector of the sky at an altitude of about 850 km in December of 1981. Strong jumps (about 80 mV/m) in the electric and magnetic fields and fluctuations of ion density were detected within the disturbance. The electric and magnetic fields were characterized by a distinct spatial-temporal relationship typical for a standing quasi-monochromatic wave with a frequency of 1 Hz. The ratio of the amplitudes of electric and magnetic fluctuations was equal to the velocity of Alfven waves. The strong parallel component of the electric field (about 30 mV/m) and the large ion density of the fluctuations indicate changes in the plasma properties of the disturbance. The possibility of anomalous resistivity effects in the disturbance is also briefly considered. 23 references.

  12. Standing and travelling waves in a spherical brain model: The Nunez model revisited

    Science.gov (United States)

    Visser, S.; Nicks, R.; Faugeras, O.; Coombes, S.

    2017-06-01

    The Nunez model for the generation of electroencephalogram (EEG) signals is naturally described as a neural field model on a sphere with space-dependent delays. For simplicity, dynamical realisations of this model either as a damped wave equation or an integro-differential equation, have typically been studied in idealised one dimensional or planar settings. Here we revisit the original Nunez model to specifically address the role of spherical topology on spatio-temporal pattern generation. We do this using a mixture of Turing instability analysis, symmetric bifurcation theory, centre manifold reduction and direct simulations with a bespoke numerical scheme. In particular we examine standing and travelling wave solutions using normal form computation of primary and secondary bifurcations from a steady state. Interestingly, we observe spatio-temporal patterns which have counterparts seen in the EEG patterns of both epileptic and schizophrenic brain conditions.

  13. Thick brane isotropization in the 5D anisotropic standing wave braneworld model

    CERN Document Server

    Gogberashvili, Merab; Malagon-Morejon, Dagoberto; Mora-Luna, Refugio Rigel; Nucamendi, Ulises

    2014-01-01

    We study a smooth cosmological solution of the 5D anisotropic standing wave braneworld model generated by gravity coupled to a phantom-like scalar field. In this model the brane emits anisotropic waves into the bulk with different amplitudes along different spatial dimensions. We found a natural mechanism which isotropizes the braneworld, rendering a 3-brane with de Sitter symmetry embedded in a 5D de Sitter space-time for a wide class of initial conditions. The resulting thick geometrical braneworld (a de Sitter 3-brane) possesses a series of remarkable features. By explicitly solving the bulk field equations we are able to give a physical interpretation of the anisotropic dissipation: as the anisotropic energy on the 3-brane rapidly leaks into the bulk, through the nontrivial Weyl tensor components, the bulk becomes less isotropic.

  14. First-principle simulation of the acoustic radiation force on microparticles in ultrasonic standing waves

    DEFF Research Database (Denmark)

    Jensen, Mads Jakob Herring; Bruus, Henrik

    2013-01-01

    The recent development in the field of microparticle acoutophoresis in microsystems has led to an increased need for more accurate theoretical predections for the acoustic radiation force on a single microparticle in an ultrasonic standing wave. Increasingly detailed analytical solutions of this ......The recent development in the field of microparticle acoutophoresis in microsystems has led to an increased need for more accurate theoretical predections for the acoustic radiation force on a single microparticle in an ultrasonic standing wave. Increasingly detailed analytical solutions...... of this specific problem can be found in the literature [Settnes ans Bruus, Phys. Rev. E 85, 016327 (2012), and references therein], but none have included the complete contribution from thermoviscous effects. Here, we solve this problem numerically by applying a finite-element method to solve directly the mass...... (continuity), momentum (Navier-Stokes), and energy conservation equations using perturbation theory to second order in the imposed time-harmonic ultrasound field. In a two-stage calculation, we first solve the first-order equations resolving the thermoviscous boundary layer surrounding the microparticle...

  15. Stable optical trapping and sensitive characterization of nanostructures using standing-wave Raman tweezers

    Science.gov (United States)

    Wu, Mu-ying; Ling, Dong-xiong; Ling, Lin; Li, William; Li, Yong-qing

    2017-01-01

    Optical manipulation and label-free characterization of nanoscale structures open up new possibilities for assembly and control of nanodevices and biomolecules. Optical tweezers integrated with Raman spectroscopy allows analyzing a single trapped particle, but is generally less effective for individual nanoparticles. The main challenge is the weak gradient force on nanoparticles that is insufficient to overcome the destabilizing effect of scattering force and Brownian motion. Here, we present standing-wave Raman tweezers for stable trapping and sensitive characterization of single isolated nanostructures with a low laser power by combining a standing-wave optical trap with confocal Raman spectroscopy. This scheme has stronger intensity gradients and balanced scattering forces, and thus can be used to analyze many nanoparticles that cannot be measured with single-beam Raman tweezers, including individual single-walled carbon nanotubes (SWCNT), graphene flakes, biological particles, SERS-active metal nanoparticles, and high-refractive semiconductor nanoparticles. This would enable sorting and characterization of specific SWCNTs and other nanoparticles based on their increased Raman fingerprints. PMID:28211526

  16. Stable optical trapping and sensitive characterization of nanostructures using standing-wave Raman tweezers

    Science.gov (United States)

    Wu, Mu-Ying; Ling, Dong-Xiong; Ling, Lin; Li, William; Li, Yong-Qing

    2017-02-01

    Optical manipulation and label-free characterization of nanoscale structures open up new possibilities for assembly and control of nanodevices and biomolecules. Optical tweezers integrated with Raman spectroscopy allows analyzing a single trapped particle, but is generally less effective for individual nanoparticles. The main challenge is the weak gradient force on nanoparticles that is insufficient to overcome the destabilizing effect of scattering force and Brownian motion. Here, we present standing-wave Raman tweezers for stable trapping and sensitive characterization of single isolated nanostructures with a low laser power by combining a standing-wave optical trap with confocal Raman spectroscopy. This scheme has stronger intensity gradients and balanced scattering forces, and thus can be used to analyze many nanoparticles that cannot be measured with single-beam Raman tweezers, including individual single-walled carbon nanotubes (SWCNT), graphene flakes, biological particles, SERS-active metal nanoparticles, and high-refractive semiconductor nanoparticles. This would enable sorting and characterization of specific SWCNTs and other nanoparticles based on their increased Raman fingerprints.

  17. Measurements of the force fields within an acoustic standing wave using holographic optical tweezers

    Energy Technology Data Exchange (ETDEWEB)

    Bassindale, P. G.; Drinkwater, B. W. [Faculty of Engineering, Queens building, University of Bristol, Bristol BS8 1TR (United Kingdom); Phillips, D. B. [Department of Physics and Astronomy, University of Glasgow, Glasgow G12 8QQ (United Kingdom); Barnes, A. C. [Department of Physics, H.H.Wills Physics Laboratory, University of Bristol, Tyndall Avenue, Bristol BS8 1TL (United Kingdom)

    2014-04-21

    Direct measurement of the forces experienced by micro-spheres in an acoustic standing wave device have been obtained using calibrated optical traps generated with holographic optical tweezers. A micro-sphere, which is optically trapped in three dimensions, can be moved through the acoustic device to measure forces acting upon it. When the micro-sphere is subjected to acoustic forces, it's equilibrium position is displaced to a position where the acoustic forces and optical forces are balanced. Once the optical trapping stiffness has been calibrated, observation of this displacement enables a direct measurement of the forces acting upon the micro-sphere. The measured forces are separated into a spatially oscillating component, attributed to the acoustic radiation force, and a constant force, attributed to fluid streaming. As the drive conditions of the acoustic device were varied, oscillating forces (>2.5 pN{sub pp}) and streaming forces (<0.2 pN) were measured. A 5 μm silica micro-sphere was used to characterise a 6.8 MHz standing wave, λ = 220 μm, to a spatial resolution limited by the uncertainty in the positioning of the micro-sphere (here to within 2 nm) and with a force resolution on the order of 10 fN. The results have application in the design and testing of acoustic manipulation devices.

  18. Potential health effects of standing waves generated by low frequency noise.

    Science.gov (United States)

    Ziaran, Stanislav

    2013-01-01

    The main aim is to present the available updated knowledge regarding the potential health effects of standing waves generated by low frequency noise (LFN) from an open window in a moving car where the negative effects of LFN induced by heating components and/or heating, ventilation and air-conditioning are assessed. Furthermore, the assessment of noise in chosen enclosed spaces, such as rooms, offices, and classrooms, or other LFN sources and their effect on the human being were investigated. These types of noise are responsible for disturbance during relaxation, sleep, mental work, education, and concentration, which may reflect negatively on the comfort and health of the population and on the mental state of people such as scientific staff and students. The assessment points out the most exposed areas, and analyzes the conditions of standing wave generation in these rooms caused by outdoor and/or indoor sources. Measurements were made for three different enclosed spaces (office, flat, and passenger car) and sources (traffic specific noise at intersections, noise induced by pipe vibration, and aerodynamic noise) and their operating conditions. For the detection of LFN, the A-weighted sound pressure level and vibration were measured and a fast Fourier transform analysis was used. The LFN sources are specified and the direct effects on the human are reported. Finally, this paper suggests the possibilities for the assessment of LFN and some possible measures that can be taken to prevent or reduce them.

  19. Coronal Seismology of Flare-Excited Standing Slow-Mode Waves Observed by SDO/AIA

    Science.gov (United States)

    Wang, Tongjiang; Ofman, Leon; Davila, Joseph M.

    2016-05-01

    Flare-excited longitudinal intensity oscillations in hot flaring loops have been recently detected by SDO/AIA in 94 and 131 Å bandpasses. Based on the interpretation in terms of a slow-mode wave, quantitative evidence of thermal conduction suppression in hot (>9 MK) loops has been obtained for the first time from measurements of the polytropic index and phase shift between the temperature and density perturbations (Wang et al. 2015, ApJL, 811, L13). This result has significant implications in two aspects. One is that the thermal conduction suppression suggests the need of greatly enhanced compressive viscosity to interpret the observed strong wave damping. The other is that the conduction suppression provides a reasonable mechanism for explaining the long-duration events where the thermal plasma is sustained well beyond the duration of impulsive hard X-ray bursts in many flares, for a time much longer than expected by the classical Spitzer conductive cooling. In this study, we model the observed standing slow-mode wave in Wang et al. (2015) using a 1D nonlinear MHD code. With the seismology-derived transport coefficients for thermal conduction and compressive viscosity, we successfully simulate the oscillation period and damping time of the observed waves. Based on the parametric study of the effect of thermal conduction suppression and viscosity enhancement on the observables, we discuss the inversion scheme for determining the energy transport coefficients by coronal seismology.

  20. Two-dimensional manipulation of microparticles using phase-controllable ultrasonic standing waves

    Science.gov (United States)

    Courtney, C. R. P.; Ong, C.-K.; Drinkwater, B. W.; Wilcox, P. D.; Grinenko, A.

    2012-05-01

    The ability to trap, and then manipulate, micro-particles in a fluid, is of interest as a research tool in the biosciences. Applications include tissue engineering, particle sorting and improving alignment with bio-sensors. This paper relates to the use of phase-controllable counter-propagating ultrasonic waves to generate a standing wave with pressure nodes whose positions are determined by the relative phases of the component counter-propagating travelling waves. As dense (relative to the fluid) particles are forced to nodes in the pressure field this allows particles to be trapped at particular points and moved to arbitrary positions. Counter-propagating waves are generated using pairs of opposing transducers, matched and backed to minimise reflection. Using one pair of transducers allows particles to be trapped and manipulated in one dimension. Using two pairs of transducers, positioned orthogonally, and adjusting the relative phases appropriately, allows trapping and manipulation in two dimensions. The device is shown experimentally to be capable of trapping and manipulating 10-micron-diameter polystyrene beads in two dimensions.

  1. SoC-Based Output Voltage Control for BESS with a Lithium-Ion Battery in a Stand-Alone DC Microgrid

    Directory of Open Access Journals (Sweden)

    Seung-Yeong Yu

    2016-11-01

    Full Text Available This paper proposes a new DC output voltage control for a battery energy storage system (BESS with a lithium-ion battery based on the state of charge (SoC. The proposed control scheme was verified through computer simulations for a typical stand-alone DC microgrid, which consists of a BESS, photovoltaic (PV panel, engine generator (EG, and DC load. A scaled hardware prototype for a stand-alone DC microgrid was set up in the lab, in which the proposed control scheme was loaded in a DSP controller. The experimental results were compared with the simulation results for performance verification. The proposed control scheme provides relatively lower variation of the DC grid voltage than the conventional droop control.

  2. MOSFET-based high voltage double square-wave pulse generator with an inductive adder configuration

    Energy Technology Data Exchange (ETDEWEB)

    Zhao, Xin [State Key Laboratory of Electrical Insulation and Power Equipment, Xi' an Jiaotong University, Xi' an 710049 (China); Zhang, Qiaogen, E-mail: hvzhang@mail.xjtu.edu.cn [State Key Laboratory of Electrical Insulation and Power Equipment, Xi' an Jiaotong University, Xi' an 710049 (China); Long, Jinghua [College of Physics, Shenzhen University, Shenzhen 518060 (China); Lei, Yunfei; Liu, Jinyuan [Institute of Optoelectronics, Shenzhen University, Shenzhen 518060 (China)

    2015-09-01

    This paper presents a fast MOSFET-based solid-state pulse generator for high voltage double square-wave pulses. The generator consists mainly of an inductive adder system stacked of 20 solid-state modules. Each of the modules has 18 power MOSFETs in parallel, which are triggered by individual drive circuits; these drive circuits themselves are synchronously triggered by a signal from avalanche transistors. Our experiments demonstrate that the output pulses with amplitude of 8.1 kV and peak current of about 405 A are available at a load impedance of 20 Ω. The pulse has a double square-wave form with a rise and fall time of 40 ns and 26 ns, respectively and bottom flatness better than 12%. The interval time of the double square-wave pulses can be adjustable by varying the interval time of the trigger pulses.

  3. Generation of uniform large-area very high frequency plasmas by launching two specific standing waves simultaneously

    Energy Technology Data Exchange (ETDEWEB)

    Chen, Hsin-Liang, E-mail: hlchen@iner.gov.tw; Tu, Yen-Cheng; Hsieh, Cheng-Chang; Lin, Deng-Lain [Physics Division, Institute of Nuclear Energy Research (INER), Longtan, Taoyuan County 32546, Taiwan (China); Leou, Keh-Chyang [Department of Engineering and System Science, National Tsing Hua University, 101, Section 2, Kuang-Fu Road, Hsinchu 30013, Taiwan (China)

    2014-09-14

    With the characteristics of higher electron density and lower ion bombardment energy, large-area VHF (very high frequency) plasma enhanced chemical vapor deposition has become an essential manufacturing equipment to improve the production throughput and efficiency of thin film silicon solar cell. However, the combination of high frequency and large electrodes leads to the so-called standing wave effect causing a serious problem for the deposition uniformity of silicon thin film. In order to address this issue, a technique based on the idea of simultaneously launching two standing waves that possess similar amplitudes and are out of phase by 90° in time and space is proposed in this study. A linear plasma reactor with discharge length of 54 cm is tested with two different frequencies including 60 and 80 MHz. The experimental results show that the proposed technique could effectively improve the non-uniformity of VHF plasmas from >±60% when only one standing wave is applied to <±10% once two specific standing waves are launched at the same time. Moreover, in terms of the reactor configuration adopted in this study, in which the standing wave effect along the much shorter dimension can be ignored, the proposed technique is applicable to different frequencies without the need to alter the number and arrangement of power feeding points.

  4. Illustrations and supporting texts for sound standing waves of air columns in pipes in introductory physics textbooks

    Directory of Open Access Journals (Sweden)

    Liang Zeng

    2014-07-01

    Full Text Available In our pilot studies, we found that many introductory physics textbook illustrations with supporting text for sound standing waves of air columns in open-open, open-closed, and closed-closed pipes inhibit student understanding of sound standing wave phenomena due to student misunderstanding of how air molecules move within these pipes. Based on the construct of meaningful learning from cognitive psychology and semiotics, a quasiexperimental study was conducted to investigate the comparative effectiveness of two alternative approaches to student understanding: a traditional textbook illustration approach versus a newly designed air molecule motion illustration approach. Thirty volunteer students from introductory physics classes were randomly assigned to two groups of 15 each. Both groups were administered a presurvey. Then, group A read the air molecule motion illustration handout, and group B read a traditional textbook illustration handout; both groups were administered postsurveys. Subsequently, the procedure was reversed: group B read the air molecule motion illustration handout and group A read the traditional textbook illustration handout. This was followed by a second postsurvey along with an exit research questionnaire. The study found that the majority of students experienced meaningful learning and stated that they understood sound standing wave phenomena significantly better using the air molecule motion illustration approach. This finding provides a method for physics education researchers to design illustrations for abstract sound standing wave concepts, for publishers to improve their illustrations with supporting text, and for instructors to facilitate deeper learning in their students on sound standing waves.

  5. Development of fast two-dimensional standing wave microscopy using acousto-optic deflectors

    Science.gov (United States)

    Gliko, Olga; Reddy, Duemani G.; Brownell, William E.; Saggau, Peter

    2008-02-01

    A novel scheme for two-dimensional (2D) standing wave fluorescence microscopy (SWFM) using acousto-optic deflectors (AODs) is proposed. Two laser beams were coupled into an inverted microscope and focused at the back focal plane of the objective lens. The position of each of two beams at the back focal plane was controlled by a pair of AODs. This resulted in two collimated beams that interfered in the focal plane, creating a lateral periodic excitation pattern with variable spacing and orientation. The phase of the standing wave pattern was controlled by phase delay between two RF sinusoidal signals driving the AODs. Nine SW patterns of three different orientations about the optical axis and three different phases were generated. The excitation of the specimen using these patterns will result in a SWFM image with enhanced 2D lateral resolution with a nearly isotropic effective point-spread function. Rotation of the SW pattern relative to specimen and varying the SW phase do not involve any mechanical movements and are only limited by the time required for the acoustic wave to fill the aperture of AOD. The resulting total acquisition time can be as short as 100 µs and is only further limited by speed and sensitivity of the employed CCD camera. Therefore, this 2D SWFM can provide a real time imaging of subresolution processes such as docking and fusion of synaptic vesicles. In addition, the combination of 2D SWFM with variable angle total internal reflection (TIR) can extend this scheme to fast microscopy with enhanced three-dimensional (3D) resolution.

  6. Radio-frequency sheath voltages and slow wave electric field spatial structure

    Energy Technology Data Exchange (ETDEWEB)

    Colas, Laurent, E-mail: laurent.colas@cea.fr; Lu, Ling-Feng [CEA, IRFM, F-13108 Saint-Paul-Lez-Durance (France); Křivská, Alena [LPP-ERM-KMS, TEC partner, Brussels (Belgium); Jacquot, Jonathan [Max-Planck-Institut für Plasmaphysik, Garching (Germany)

    2015-12-10

    We investigate theoretically how sheath radio-frequency (RF) oscillations relate to the spatial structure of the RF parallel electric field emitted by Ion Cyclotron (IC) wave launchers, using a simple model of Slow Wave (SW) evanescence coupled with Direct Current (DC) plasma biasing via sheath boundary conditions in a plasma-filled 2-dimensional (parallel, radial) rectangle. Within a “wide sheaths” asymptotic regime, valid for large-amplitude near RF fields, our model becomes partly linear: the sheath oscillating voltage at open field line boundaries is a linear combination of elementary contributions by every source point of the radiated RF field map. These individual contributions are all the more intense as the SW emission point is toroidally nearer to the sheath walls. A limit formula is given for a source infinitely close to the sheaths. The decay of sheath RF voltages with the sheath/source parallel distance is quantified as a function of two characteristic SW evanescence lengths. Decay lengths are smaller than antenna parallel extensions. The sheath RF voltages at an IC antenna side limiter are therefore mainly sensitive to SW emission near this limiter, as recent observations suggest. Toroidal proximity effects could also explain why sheath oscillations persist with antisymmetric strap toroidal phasing, despite the parallel anti-symmetry of the radiated field map. They could also justify current attempts at reducing the RF fields induced near antenna boxes to attenuate sheath oscillations in their vicinity.

  7. Specifics of operation of a cold-cathode thyratron with a backward voltage half-wave

    Science.gov (United States)

    Korolev, Yu. D.; Landl, N. V.; Geiman, V. G.; Frants, O. B.; Bolotov, A. V.; Nekhoroshev, V. O.; Kasyanov, V. S.

    2017-05-01

    The specifics of operating a metal-ceramic TPI1-10k/50 thyratron in electric circuits with capacitance, inductance, and active resistance have been examined under circuit parameters that establish oscillatory current. Experiments have been performed at an anode voltage as high as 30 kV, a forward current of up to 7.6 kA, and a length of the first current half-period that varies from 0.38 to 1.9 μs. The data on operating modes in which this thyratron may handle a backward current wave and when current interruption is observed in the second half-period have been obtained. It has been demonstrated that a certain current flows through the thyratron in the backward direction during the interruption process. The amplitude of this current and the maximum backward voltage at the thyratron define whether the current is interrupted or repeat back-voltage device breakdown occurs. If the maximum backward current is on the level of several hundred amperes, complete current interruption occurs at backward voltages of up to 12 kV. The physical mechanisms of current interruption have been discussed.

  8. Experimental Study on a Standing Wave Thermoacoustic Prime Mover with Air Working Gas at Various Pressures

    Science.gov (United States)

    Setiawan, Ikhsan; Achmadin, Wahyu N.; Murti, Prastowo; Nohtomi, Makoto

    2016-04-01

    Thermoacoustic prime mover is an energy conversion device which converts thermal energy into acoustic work (sound wave). The advantages of this machine are that it can work with air as the working gas and does not produce any exhaust gases, so that it is environmentally friendly. This paper describes an experimental study on a standing wave thermoacoustic prime mover with air as the working gas at various pressures from 0.05 MPa to 0.6 MPa. We found that 0.2 MPa is the optimum pressure which gives the lowest onset temperature difference of 355 °C. This pressure value would be more preferable in harnessing low grade heat sources to power the thermoacoustic prime mover. In addition, we find that the lowest onset temperature difference is obtained when rh /δ k ratio is 2.85, where r h is the hydraulic radius of the stack and δ k is the thermal penetration depth of the gas. Moreover, the pressure amplitude of the sound wave is significantly getting larger from 2.0 kPa to 9.0 kPa as the charged pressure increases from 0.05 MPa up to 0.6 MPa.

  9. Self-organization of clusters by a standing surface acoustic wave

    Science.gov (United States)

    Taillan, Christophe; Combe, Nicolas; Morillo, Joseph

    2017-07-01

    The diffusion of clusters on a crystalline substrate submitted to a standing surface acoustic wave (StSAW) is studied using molecular dynamics simulations. The distributions of positions of clusters with two, three, and four atoms are calculated and evidence that the wave encourages the presence of the clusters in the vicinity of the maximum transverse displacement field of the substrate. The physical mechanism leading to this self-organization is expected to be equivalent to the one operating for a single adatom, i.e., the displacement of the clusters induced by the longitudinal displacement field of the wave. The detailed shapes of the distributions of positions of clusters are related to the different clusters' orientation and configurations. Finally, the possibility to use a StSAW to self-organize nanostructures during growth is addressed by simulating a deposition process on the substrate. We evidence that the use of a StSAW allows to especially control the spatial repartition of grown nanostructures.

  10. In vitro ultrasound experiments: Standing wave and multiple reflections influence on the outcome.

    Science.gov (United States)

    Secomski, Wojciech; Bilmin, Krzysztof; Kujawska, Tamara; Nowicki, Andrzej; Grieb, Paweł; Lewin, Peter A

    2017-05-01

    The purpose of this work was to determine the influence of standing waves and possible multiple reflections under the conditions often encountered in examining the effects of ultrasound exposure on the cell cultures in vitro. More specifically, the goal was to quantitatively ascertain the influence of ultrasound exposure under free field (FF) and standing waves (SW) and multiple reflections (MR) conditions (SWMR) on the biological endpoint (50% cell necrosis). Such information would help in designing the experiments, in which the geometry of the container with biological tissue may prevent FF conditions to be established and in which the ultrasound generated temperature elevation is undesirable. This goal was accomplished by performing systematic, side-by-side experiments in vitro with C6 rat glioma cancer cells using 12 well and 96 well plates. It was determined that to obtain 50% of cell viability using the 12 well plates, the spatial average, temporal average (ISATA) intensities of 0.32W/cm(2) and 5.89W/cm(2) were needed under SWMR and FF conditions, respectively. For 96 well plates the results were 0.80W/cm(2) and 2.86W/cm(2) respectively. The corresponding, hydrophone measured pRMS maximum pressure amplitude values, were 0.71MPa, 0.75MPa, 0.75MPa and 0.73MPa, respectively. These results suggest that pRMS pressure amplitude was independent of the measurement set-up geometry and hence could be used to predict the cells' mortality threshold under any in vitro experimental conditions or even as a starting point for (pre-clinical) in vivo tests. The described procedure of the hydrophone measurements of the pRMS maximum pressure amplitude at the λ/2 distance (here 0.75mm) from the cell's level at the bottom of the dish or plate provides the guideline allowing the difference between the FF and SWMR conditions to be determined in any experimental setup. The outcome of the measurements also indicates that SWMR exposure might be useful at any ultrasound assisted

  11. Standing-wave-excited multiplanar fluorescence in a laser scanning microscope reveals 3D information on red blood cells

    CERN Document Server

    Amor, Rumelo; Amos, William Bradshaw; McConnell, Gail

    2014-01-01

    Standing-wave excitation of fluorescence is highly desirable in optical microscopy because it improves the axial resolution. We demonstrate here that multiplanar excitation of fluorescence by a standing wave can be produced in a single-spot laser scanning microscope by placing a plane reflector close to the specimen. We report that the relative intensities in each plane of excitation depend on the Stokes shift of the fluorochrome. We show by the use of dyes specific for the cell membrane how standing-wave excitation can be exploited to generate precise contour maps of the surface membrane of red blood cells, with an axial resolution of ~90 nm. The method, which requires only the addition of a plane mirror to an existing confocal laser scanning microscope, may well prove useful in studying diseases which involve the red cell membrane, such as malaria.

  12. Axial acoustic radiation force on rigid oblate and prolate spheroids in Bessel vortex beams of progressive, standing and quasi-standing waves

    CERN Document Server

    Mitri, F G

    2016-01-01

    The analysis using the partial-wave series expansion (PWSE) method in spherical coordinates is extended to evaluate the acoustic radiation force experienced by rigid oblate and prolate spheroids centered on the axis of wave propagation of high-order Bessel vortex beams composed of progressive, standing and quasi-standing waves, respectively. A coupled system of linear equations is derived after applying the Neumann boundary condition for an immovable surface in a non-viscous fluid, and solved numerically by matrix inversion after performing a single numerical integration procedure. The system of linear equations depends on the partial-wave index n and the order of the Bessel vortex beam m using truncated but converging PWSEs in the least-squares sense. Numerical results for the radiation force function, which is the radiation force per unit energy density and unit cross-sectional surface, are computed with particular emphasis on the amplitude ratio describing the transition from the progressive to the pure st...

  13. One-Step Generation of Scalable Multiparticle Entanglement for Hot Ions Driven by a Standing-Wave Laser

    Institute of Scientific and Technical Information of China (English)

    杨文星; 陈爱喜

    2011-01-01

    An alternative scheme is proposed for one-step generation of multiparticle cluster state with trapped ions in thermal motion. In this scheme, the ions are simultaneously illuminated by a standing-wave laser tuned to the carrier. During the operations, the vibrational mode is virtually excited, thus the quantum operations are insensitive to the heating. It is shown that the high fidelity multiparticle entanglement could be generated in just one step even including the small fluctuations of parameters. In addition, the ion does not need to be exactly positioned at the node of the standing wave, which is also important from the viewpoint of experiment.

  14. Microchannel-free collection and single-cell isolation of yeast cells in a suspension using liquid standing wave

    Science.gov (United States)

    Matsutani, Akihiro; Takada, Ayako

    2016-11-01

    We demonstrate a microchannel-free collection method at nodes of liquid standing waves by the vertical vibration of a suspension including yeast cells. The pattern formation of the collection of cells using standing waves in a suspension was investigated by varying the frequency and waveform of vibrations. The single-cell isolation of yeast cells was achieved using a microenclosure array set at the nodes. In addition, we succeeded in the microchannel-free collection of yeast cells in a suspension, where patterns were formed by tapping vibration. The proposed technique is very simple and we believe that it will be useful for single-cell analysis and investigation.

  15. High-fidelity simulation of a standing-wave thermoacoustic-piezoelectric engine

    CERN Document Server

    Lin, Jeffrey; Hesselink, Lambertus

    2015-01-01

    We have carried out wall-resolved fully unstructured Navier--Stokes simulations of a complete standing-wave thermoacoustic piezoelectric (TAP) engine model inspired by the experimental work of Smoker et al. (2012). The computational model is axisymmetric and comprises a 51 cm long cylindrical resonator divided into two sections: one of 19.5 mm in diameter, enclosing a thermoacoustic stack where a linear temperature distribution is imposed via isothermal boundary conditions; the other of 71 mm in diameter, capped by a piezoelectric diaphragm modelled via multi-oscillator broadband time-domain impedance boundary conditions (TDIBCs) matching the measured electromechanical impedance of a PZT-5A diaphragm tuned to the thermoacoustically amplified mode (388 Hz) for maximization of acoustic energy extraction. Simulations were first carried out without energy extraction from quiescent conditions to a limit cycle, for hot-to-cold temperature differences in the range $\\Delta T = 340 - 490\\textrm{ K}$, achieving acousti...

  16. Physical design and cooling test of C-band standing wave accelerating tube

    Institute of Scientific and Technical Information of China (English)

    Bai Wei; Xu Zhou; Jin Xiao; Li Ming

    2006-01-01

    The physical design and cooling test of a C-band 2MeV standing wave (SW) accelerating tube are described in this paper. The designed accelerating structure consists of 3-cell buncher and 4-cell accelerating section with a total length of about 163mm , excited with 1MW magnetron. Dynamic simulation presents that about 150mA beam pulse current and 30% capture efficiency can be achieved. By means of nonlinear Gauss fit on electron transverse distribution, the diameter of beam spot FWHM (full width at half maximum of density distribution) is about 0.55mm. Cooling test results of the accelerating tube show that frequencies of cavities are tuned to 5527MHz and the field distribution of bunching section is about 3:9:10.

  17. Theoretical research and experimental study for a new measurement method of standing wave levitation force

    Energy Technology Data Exchange (ETDEWEB)

    Li, Xinbo; Jiang, Hai; Jiao, Xiaoyang; Zhang, Kai; Liu, Guojun; Liu, Jianfang [Jilin University, Changchun (China)

    2015-05-15

    Based on the lever principle, a novel measurement method for the standing wave levitation force is investigated and the measurement device is developed. The relative levitation force was simulated by MATLAB software, from which the relative levitation force distribution and the curves of relative levitation force in vertical and horizontal directions were obtained. To verify the rationale of the measurement method, a series of experiments were carried out with the designed measurement device system. The levitation force distribution and the curves of levitation force in vertical and horizontal directions were also obtained from the experiment. Comparing the experimental results with the simulation, the levitation force distribution situation from the experimental results and the simulation is identical.

  18. Gene Expression Analysis of Mouse Embryonic Stem Cells Following Levitation in an Ultrasound Standing Wave Trap

    Science.gov (United States)

    Bazou, Despina; Kearney, Roisin; Mansergh, Fiona; Bourdon, Celine; Farrar, Jane; Wride, Michael

    2011-01-01

    In the present paper, gene expression analysis of mouse embryonic stem (ES) cells levitated in a novel ultrasound standing wave trap (USWT) (Bazou et al. 2005a) at variable acoustic pressures (0.08–0.85 MPa) and times (5–60 min) was performed. Our results showed that levitation of ES cells at the highest employed acoustic pressure for 60 min does not modify gene expression and cells maintain their pluripotency. Embryoid bodies (EBs) also expressed the early and late neural differentiation markers, which were also unaffected by the acoustic field. Our results suggest that the ultrasound trap microenvironment is minimally invasive as the biologic consequences of ES cell replication and EB differentiation proceed without significantly affecting gene expression. The technique holds great promise in safe cell manipulation techniques for a variety of applications including tissue engineering and regenerative medicine. (E-mail: Bazoud@tcd.ie) PMID:21208732

  19. Temporal coupled mode theory of standing wave resonant cavities for infrared photodetection.

    Science.gov (United States)

    Lesmanne, Emeline; De Lamaestre, Roch Espiau; Fowler, David; Boutami, Salim; Badano, Giacomo

    2015-03-23

    Standing wave resonating cavities have been proposed in the past to increase the performance of infrared detectors by minimizing the volume of photogeneration, hence the noise, while maintaining the same quantum efficiency. We present an approach based on the temporal coupled mode theory to explain their behavior and limitations. If the ratio of the imaginary part of the absorber's dielectric function to the index of the incident medium ε″(d)/n₀ is larger than 1.4, then the absorption cross section σ(a) can attain its maximum value, which for an isolated cavity is approximately 2λ/π. Besides, for σ(a) to exceed the cavity width, the incident medium refractive index must be close to unity. Metallic loss is negligible in the infrared, making those resonators suitable for integration in infrared photodetectors.

  20. Model independent X-ray standing wave analysis of periodic multilayer structures

    CERN Document Server

    Yakunin, S N; Chuev, M A; Pashaev, E M; Zoethout, E; Louis, E; van de Kruijs, R W E; Seregin, S Yu; Subbotin, I A; Novikov, D V; Bijkerk, F; Kovalchuk, M V

    2013-01-01

    We present a model independent approach for the reconstruction of the atomic concentration profile in a nanoscale layered structure, as measured using the X-ray fluorescence yield modulated by an X-ray standing wave (XSW). The approach is based on the direct regularized solution of the system of linear equations that characterizes the fluorescence yield. The suggested technique was optimized for, but not limited to, the analysis of periodic layered structures where the XSW is formed under Bragg conditions. The developed approach was applied to the reconstruction of the atomic concentration profiles for LaN/BN multilayers with 50 periods of 35 A thick layers. The object is especially difficult to analyse with traditional methods, as the estimated thickness of the interface region between the constituent materials is comparable to the individual layer thicknesses. However, using the suggested technique it was possible to reconstruct the La atomic profile, showing that the La atoms stay localized within the LaN ...

  1. Cavity-enhanced laser cooling of solid-state materials in a standing-wave cavity

    Institute of Scientific and Technical Information of China (English)

    Youhua Jia; Biao Zhong; Jianping Yin

    2008-01-01

    We propose a new method to cool the Yba+-doped ZBLANP glass in a standing-wave cavity. There are two advantages of this cavity-enhanced technique: the pumping power is greatly enhanced and the absorption of the cooling material is greatly increased. We introduce the basic principle of the cavity-enhanced laser cooling and discuss the cooling effect of a solid-state material in a cavity. From the theoretical study, it is found that the laser cooling effect is strongly dependent on the reflectivity of the cavity mirrors, the length of the solid material, the surface scattering of the material, and so on. Some optimal parameters for efficient laser cooling are obtained.

  2. Mini-Scale Power Distribution Network Feeding Trapezoidal-Wave Voltages to Power Electronic Loads with Diode Rectifiers

    Science.gov (United States)

    Noguchi, Toshihiko; Imoto, Masaru; Sato, Yoshikazu

    This paper proposes a novel three-phase power distribution system feeding trapezoidal voltages to various power electronic loads with diode rectifier front-ends. The network distributes trapezoidal voltages generated by synchronous superposition of wave-shaping voltages onto sinusoidal voltages available from a utility power grid. The power distribution by the trapezoidal voltages allows reducing harmonics of the line currents without electronic switching devices because of a spontaneously widened conduction period of the current waveforms. The reduction of the harmonic currents also contributes to improve total power factor at the load input terminals and efficiency of the power transmission cables. Since the diodes of the rectifiers successively commutate the trapezoidal waves during periods of their flat parts, not only total harmonic distortion of the currents is improved, but also voltage ripple across the dc-buses of the rectifiers can effectively be reduced with less filter capacitors. In addition, the system offers an uninterruptible power supply function by immediately changing its outputs from the wave-shaping voltages to the trapezoidal voltages when interruption occurs in the power grid. In this paper, a prototype of the system is experimentally examined from various angles of operating characteristics and test results are presented to prove feasibility of the proposed system.

  3. Numerical simulation of standing wave with 3D predictor-corrector finite difference method for potential flow equations

    Institute of Scientific and Technical Information of China (English)

    罗志强; 陈志敏

    2013-01-01

    A three-dimensional (3D) predictor-corrector finite difference method for standing wave is developed. It is applied to solve the 3D nonlinear potential flow equa-tions with a free surface. The 3D irregular tank is mapped onto a fixed cubic tank through the proper coordinate transform schemes. The cubic tank is distributed by the staggered meshgrid, and the staggered meshgrid is used to denote the variables of the flow field. The predictor-corrector finite difference method is given to develop the difference equa-tions of the dynamic boundary equation and kinematic boundary equation. Experimental results show that, using the finite difference method of the predictor-corrector scheme, the numerical solutions agree well with the published results. The wave profiles of the standing wave with different amplitudes and wave lengths are studied. The numerical solutions are also analyzed and presented graphically.

  4. Operation of High-Voltage Transverse Shock Wave Ferromagnetic Generator in the Open Circuit and Charging Modes

    Science.gov (United States)

    2005-06-01

    FMGs are based on the transverse (when the shock wave propagates across the magnetization vector M) shock demagnetization of Nd2Fe14B hard...generators based on the transverse (when the shock wave propagates across the magnetization vector M) shock wave demagnetization of Nd2Fe14B hard...and photo of a high-voltage transverse FMG are shown in Fig. 1. It contains a hollow hard ferromagnetic cylindrical Nd2Fe14B energy-carrying

  5. Fluorescence x-ray standing wave study on (AlAs)(GaAs) superlattices

    CERN Document Server

    Lessmann, A; Munkholm, A; Schuster, M; Riechert, H; Materlik, G

    1999-01-01

    X-ray standing waves (XSW) were used to investigate the structure of molecular beam epitaxy (MBE) grown (AlAs) sub 3 (GaAs) sub 7 short-period superlattices (SPSL). The modulation of the Al K, As L, and Ga L x-ray fluorescence induced by XSW was measured at the zero-order superlattice (SL) satellite (AlAs)(GaAs)(004,0) and the GaAs(004) substrate Bragg reflection. From the shape of the fluorescence yield modulations and the diffraction pattern, a model of the interfaces is derived by comparing the experimental data with dynamical calculations of the x-ray wave field distribution and reflectivity. A straightforward analysis of the fluorescence measurements at the SL satellite shows that in AlAs layers a high crystalline order is established, whereas in GaAs layers a fraction of the Ga and As atoms is not on ideal lattice sites, but is displaced towards the substrate. The data can be explained by a model in which, at each AlAs/GaAs interface of the GaAs layers, two Ga atom planes are displaced by 0.035 nm and 0...

  6. Evidence of standing waves during a Pi2 pulsation event observed on Cluster

    Directory of Open Access Journals (Sweden)

    A. B. Collier

    2006-10-01

    Full Text Available Observations of Pi2 pulsations at middle and low latitudes have been explained in terms of cavity mode resonances, whereas transients associated with field-aligned currents appear to be responsible for the high latitude Pi2 signature.

    Data from Cluster are used to study a Pi2 event observed at 18:09 UTC on 21 January 2003, when three of the satellites were within the plasmasphere (L=4.7, 4.5 and 4.6 while the fourth was on the plasmapause or in the plasmatrough (L=6.6. Simultaneous pulsations at ground observatories and the injection of particles at geosynchronous orbit corroborate the occurrence of a substorm.

    Evidence of a cavity mode resonance is established by considering the phase relationship between the orthogonal electric and magnetic field components associated with radial and field-aligned standing waves. The relative phase between satellites located on either side of the geomagnetic equator indicates that the field-aligned oscillation is an odd harmonic. Finite azimuthal Poynting flux suggests that the cavity is effectively open ended and the azimuthal wave number is estimated as m~13.5.

  7. Separation of Escherichia coli bacteria from peripheral blood mononuclear cells using standing surface acoustic waves.

    Science.gov (United States)

    Ai, Ye; Sanders, Claire K; Marrone, Babetta L

    2013-10-01

    A microfluidic device was developed to separate heterogeneous particle or cell mixtures in a continuous flow using acoustophoresis. In this device, two identical surface acoustic waves (SAWs) generated by interdigital transducers (IDTs) propagated toward a microchannel, which accordingly built up a standing surface acoustic wave (SSAW) field across the channel. A numerical model, coupling a piezoelectric effect in the solid substrate and acoustic pressure in the fluid, was developed to provide a better understanding of SSAW-based particle manipulation. It was found that the pressure nodes across the channel were individual planes perpendicular to the solid substrate. In the separation experiments, two side sheath flows hydrodynamically focused the injected particle or cell mixtures into a very narrow stream along the centerline. Particles flowing through the SSAW field experienced an acoustic radiation force that highly depends on the particle properties. As a result, dissimilar particles or cells were laterally attracted toward the pressure nodes at different magnitudes, and were eventually switched to different outlets. Two types of fluorescent microspheres with different sizes were successfully separated using the developed device. In addition, Escherichia coli bacteria premixed in peripheral blood mononuclear cells (PBMCs) were also efficiently isolated using the SSAW-base separation technique. Flow cytometric analysis on the collected samples found that the purity of separated E. coli bacteria was 95.65%.

  8. Fluorescence x-ray standing wave study on (AlAs)(GaAs) superlattices

    Energy Technology Data Exchange (ETDEWEB)

    Lessmann, A.; Brennan, S.; Munkholm, A. [Stanford Synchrotron Radiation Laboratory SSRL/SLAC, Menlo Park, CA (United States); Schuster, M.; Riechert, H. [Siemens AG, Corporate Technology, Munich (Germany); Materlik, G. [Hamburger Synchrotronstrahlungslabor HASYLAB/DESY, Hamburg (Germany)

    1999-05-21

    X-ray standing waves (XSW) were used to investigate the structure of molecular beam epitaxy (MBE) grown (AlAs){sub 3}(GaAs){sub 7} short-period superlattices (SPSL). The modulation of the Al K, As L, and Ga L x-ray fluorescence induced by XSW was measured at the zero-order superlattice (SL) satellite (AlAs)(GaAs)(004,0) and the GaAs(004) substrate Bragg reflection. From the shape of the fluorescence yield modulations and the diffraction pattern, a model of the interfaces is derived by comparing the experimental data with dynamical calculations of the x-ray wave field distribution and reflectivity. A straightforward analysis of the fluorescence measurements at the SL satellite shows that in AlAs layers a high crystalline order is established, whereas in GaAs layers a fraction of the Ga and As atoms is not on ideal lattice sites, but is displaced towards the substrate. The data can be explained by a model in which, at each AlAs/GaAs interface of the GaAs layers, two Ga atom planes are displaced by 0.035 nm and 0.008 nm and one As atom plane by 0.023 nm. The displacements within the GaAs layers exhibit a mirror symmetry with respect to the centre of each layer. (author)

  9. Precise spatial control of cavitation erosion in a vessel phantom by using an ultrasonic standing wave.

    Science.gov (United States)

    Shi, Aiwei; Huang, Peixuan; Guo, Shifang; Zhao, Lu; Jia, Yingjie; Zong, Yujin; Wan, Mingxi

    2016-07-01

    In atherosclerotic inducement in animal models, the conventionally used balloon injury is invasive, produces excessive vessel injuries at unpredictable locations and is inconvenient in arterioles. Fortunately, cavitation erosion, which plays an important role in therapeutic ultrasound in blood vessels, has the potential to induce atherosclerosis noninvasively at predictable sites. In this study, precise spatial control of cavitation erosion for superficial lesions in a vessel phantom was realised by using an ultrasonic standing wave (USW) with the participation of cavitation nuclei and medium-intensity ultrasound pulses. The superficial vessel erosions were restricted between adjacent pressure nodes, which were 0.87 mm apart in the USW field of 1 MHz. The erosion positions could be shifted along the vessel by nodal modulation under a submillimetre-scale accuracy without moving the ultrasound transducers. Moreover, the cavitation erosion of the proximal or distal wall could be determined by the types of cavitation nuclei and their corresponding cavitation pulses, i.e., phase-change microbubbles with cavitation pulses of 5 MHz and SonoVue microbubbles with cavitation pulses of 1 MHz. Effects of acoustic parameters of the cavitation pulses on the cavitation erosions were investigated. The flow conditions in the experiments were considered and discussed. Compared to only using travelling waves, the proposed method in this paper improves the controllability of the cavitation erosion and reduces the erosion depth, providing a more suitable approach for vessel endothelial injury while avoiding haemorrhage.

  10. Direct voltage measurements using bulk acoustic wave sensing in LiNbO3

    Science.gov (United States)

    Patel, Nishant Bhupendra

    Accurate (impedance effects that can distort the pulse shape, and pickup of extraneous signals resulting from electromagnetic interference effects. A piezoelectric crystal-based bulk acoustic wave sensor using lithium niobate (LiNbO3) that has applications to metrology, research, and power metering was developed to overcome these measurement issues with the factors of scalability, ease of use, and compactness in mind. A Y+36° cut LiNbO3crystal was coupled to two acoustic transducers, where direct current (DC) voltages ranging from 128--1100 V were applied transversely to the crystal. An acoustic wave was used to interrogate the crystal before, during, and after voltage application. Both single and multiple pass measurements were performed and compared to linear piezoelectric theory. A comparison study between Y+36° and 0° X-cut LiNbO3 was performed to evaluate the influence of crystal cut on acoustic propagation. The study was extended to applying alternating current (AC), and pulsed voltages. The measured DC data was compared to a 1-D impedance matrix model that was based on a three port circuit with voltage-induced strain effects inputted as a model parameter. An uncertainty budget was carried out for both crystal cuts and compared. Environmental effects such as pressure and temperature were also measured to determine their influence on the sensor under ambient conditions. Published literature regarding material constants, such as elastic constants and piezoelectric constants, for LiNbO3 do not account for the influence of an electric field. In light of this, measurements of the acoustic velocities and material constants under the presence of a DC electric field were performed up to 896 V. This information was used to develop an uncertainty analysis for the determination of stress-charge form piezoelectric constants e15 and e22. All measured and calculated values were input into a Monte Carlo simulation to determine the error of the strain-charge form

  11. Standing and Travelling Wave Contributions to the Persistent Ridge-Trough Over North America During Winter 2013/14

    Science.gov (United States)

    Watt-Meyer, O.; Kushner, P. J.

    2015-12-01

    The winter season over North America during 2013/14 was dominated by a persistent ridge-trough that brought warm and dry conditions to the southwestern U.S., and markedly cold temperatures to central and eastern North America [Wang et al., 2014; Hartmann, 2015]. In addition, several cold air outbreaks occurred during the winter season, the strongest of which was around 7 January 2014 and led to minimum daily temperature records being set at many weather stations including Atlanta, Austin, Chicago and New York [Screen et al., in press]. This study uses a novel decomposition of wave variability into standing and travelling components [Watt-Meyer and Kushner, 2015] to diagnose the anomalous circulation of the 2013/14 winter season. This spectral decomposition is an improvement on previous methods because it explicitly accounts for the covariance between standing and travelling waves, and because the real-space components of the signal can be easily reconstructed. An index representing the ridge-trough dipole is computed using mid-tropospheric heights and shown to be well correlated with surface temperatures over central and eastern North America. The contributions to this dipole index from standing waves, westward travelling waves, and eastward travelling waves are calculated. The analysis demonstrates that the cold air outbreak of 7 January 2014 was driven by a synoptic wave of record breaking amplitude intensifying a persistent background amplification of the typical ridge-trough structure seen during North American winter.

  12. Generation of uniform large-area very high frequency plasmas by launching two specific standing waves simultaneously

    Science.gov (United States)

    Chen, Hsin-Liang; Tu, Yen-Cheng; Hsieh, Cheng-Chang; Lin, Deng-Lain; Leou, Keh-Chyang

    2014-09-01

    With the characteristics of higher electron density and lower ion bombardment energy, large-area VHF (very high frequency) plasma enhanced chemical vapor deposition has become an essential manufacturing equipment to improve the production throughput and efficiency of thin film silicon solar cell. However, the combination of high frequency and large electrodes leads to the so-called standing wave effect causing a serious problem for the deposition uniformity of silicon thin film. In order to address this issue, a technique based on the idea of simultaneously launching two standing waves that possess similar amplitudes and are out of phase by 90° in time and space is proposed in this study. A linear plasma reactor with discharge length of 54 cm is tested with two different frequencies including 60 and 80 MHz. The experimental results show that the proposed technique could effectively improve the non-uniformity of VHF plasmas from >±60% when only one standing wave is applied to reactor configuration adopted in this study, in which the standing wave effect along the much shorter dimension can be ignored, the proposed technique is applicable to different frequencies without the need to alter the number and arrangement of power feeding points.

  13. Investigation of sound field for a standing wave tube system with flow and with lateral Helmholtz resonator Ⅰ. Theoretical analysis

    Institute of Scientific and Technical Information of China (English)

    LIU Ke; LI Song; GUO Qing; HUANG Dongtao

    2005-01-01

    A lateral Helmholtz resonator added to a standing wave tube without flow has been validated as a method of noise reduction for combustion noise radiated from combustion channel of rockets or turbines. But in fact there is a flow with low velocity in the combustion channel. Therefore the theoretical analysis carried out is aimed at sound field of standing wave tube with flow and with lateral Helmholtz resonator. Certainly a relevant math-physical model should first be formulated. Here three key problems need to be solved: (1) To formulate the discontinuity condition at the joint between the standing wave tube and Helmholtz resonator in the case of flow. (2) To determine the acoustic impedance of Helnholtz resonator, considering the effects of flow, viscous and multihole. (3) To formulate the reflection condition at the end of the standing wave tube. Some formulas for analysis of the sound field in the tube with flow and with lateral Helmholtz resonator are deduced. These theoretical works have been validated by experiments.

  14. Extraction of olive oil assisted by high-frequency ultrasound standing waves.

    Science.gov (United States)

    Juliano, Pablo; Bainczyk, Fabian; Swiergon, Piotr; Supriyatna, Made Ian Maheswara; Guillaume, Claudia; Ravetti, Leandro; Canamasas, Pablo; Cravotto, Giancarlo; Xu, Xin-Qing

    2017-09-01

    High-frequency ultrasound standing waves (megasonics) have been demonstrated to enhance oil separation in the palm oil process at an industrial level. This work investigated the application of megasonics in the olive oil process on laboratory and pilot scale levels. Sound pressure level and cavitational yield distribution were characterised with hydrophones and luminol to determine associated physical and sonochemical effects inside the reactor. The effect of water addition (0%, 15%, and 30%), megasonic power levels (0%, 50%, and 100%), and malaxation time (10min, 30min, and 50min) was evaluated using response surface methodology (RSM) in a 700g batch extraction process. The RSM showed that the effect of the megasonic treatment (585kHz) in the presence of a reflector is more prominent at longer malaxation time (50min) and at higher water addition (30%) levels post-malaxation. Longer megasonic treatment of the malaxed paste (up to 15min; 220kJ/kg) increased oil extractability by up to 3.2%. When treating the malaxed paste with the same specific energy, higher oil extractability was obtained with longer treatments and low megasonic power levels in comparison to higher power levels and shorter times. Megasonic treatment of the paste before malaxation (585kHz, 10min, 146kJ/kg) and no water addition provided an increase in oil extractability of up to 3.8% with respect to the non-sonicated control. A double sonication intervention, before and after malaxation, using low (40kHz) and high (585kHz) frequency, respectively, provided up to 2.4% increase in oil extractability. A megasonic intervention post-malaxation (400 and 600kHz, 57-67min, 18-21kJ/kg) on a pilot scale using early-harvest olive fruits resulted in up to 1.7% extra oil extractability. Oil extracted under a high sonication frequency (free radical production regime) did not impact on olive oil quality parameters at reactor characterisation levels. Megasonic standing wave forces can enhance olive oil separation

  15. Structural analysis of bismuth nanowire by X-ray standing wave method

    CERN Document Server

    Saito, A; Kurata, T; Maruyama, J; Kuwahara, Y; Aono, M; Miki, K

    2003-01-01

    Bismuth forms perfect wires without any defects on a clean Si(001) surface. Despite the importance of this self-organized nanowire from the viewpoints of both surface science and device application, an analysis of the internal structure of the wire is quite difficult under the condition of a buried interface. In order to clarify the atomic structure of the wire capped by amorphous Si layers, the three-dimensional bismuth atomic site was measured with respect to the substrate Si lattice by the X-ray standing wave method. The results indicate that the absolute height of Bi atoms is 0.26 A upper from the bulklike Si(004) plane of the Si-dimer layer. For the structure inside the (004) plane, Bi atoms are in the range of +-0.5 A in the [110] direction from an intact Si-dimmer position. This result disagrees with recent reports that were derived from other analytical methods used solely for a clean surface. A new model was proposed and it suggests an influence of a burying effect for the wire structure. (author)

  16. Neocortical dynamics at multiple scales: EEG standing waves, statistical mechanics, and physical analogs.

    Science.gov (United States)

    Ingber, Lester; Nunez, Paul L

    2011-02-01

    The dynamic behavior of scalp potentials (EEG) is apparently due to some combination of global and local processes with important top-down and bottom-up interactions across spatial scales. In treating global mechanisms, we stress the importance of myelinated axon propagation delays and periodic boundary conditions in the cortical-white matter system, which is topologically close to a spherical shell. By contrast, the proposed local mechanisms are multiscale interactions between cortical columns via short-ranged non-myelinated fibers. A mechanical model consisting of a stretched string with attached nonlinear springs demonstrates the general idea. The string produces standing waves analogous to large-scale coherent EEG observed in some brain states. The attached springs are analogous to the smaller (mesoscopic) scale columnar dynamics. Generally, we expect string displacement and EEG at all scales to result from both global and local phenomena. A statistical mechanics of neocortical interactions (SMNI) calculates oscillatory behavior consistent with typical EEG, within columns, between neighboring columns via short-ranged non-myelinated fibers, across cortical regions via myelinated fibers, and also derives a string equation consistent with the global EEG model.

  17. Particle Accumulation in a Microchannel and Its Reduction by a Standing Surface Acoustic Wave (SSAW).

    Science.gov (United States)

    Sriphutkiat, Yannapol; Zhou, Yufeng

    2017-01-07

    Accumulation of particles in a high concentration on a microchannel wall is a common phenomenon in a colloidal fluid. Gradual accumulation/deposition of particles can eventually obstruct the fluid flow and lead to clogging, which seriously affects the accuracy and reliability of nozzle-based printing and causes damage to the nozzle. Particle accumulation in a 100 μm microchannel was investigated by light microscopy, and its area growth in an exponential format was used to quantify this phenomenon. The effects of the constriction angle and alginate concentration on particle accumulation were also studied. In order to reduce the clogging problem, an acoustic method was proposed and evaluated here. Numerical simulation was first conducted to predict the acoustic radiation force on the particles in the fluid with different viscosities. Interdigital transducers (IDTs) were fabricated on the LiNbO₃ wafer to produce standing surface acoustic waves (SSAW) in the microchannel. It was found that the actuation of SSAW can reduce the accumulation area in the microchannel by 2 to 3.7-fold. In summary, the particle accumulation becomes significant with the increase of the constriction angle and fluid viscosity. The SSAW can effectively reduce the particle accumulation and postpone clogging.

  18. A New Gravitational-wave Signature from Standing Accretion Shock Instability in Supernovae

    Science.gov (United States)

    Kuroda, Takami; Kotake, Kei; Takiwaki, Tomoya

    2016-09-01

    We present results from fully relativistic three-dimensional core-collapse supernova simulations of a non-rotating 15{M}⊙ star using three different nuclear equations of state (EoSs). From our simulations covering up to ˜350 ms after bounce, we show that the development of the standing accretion shock instability (SASI) differs significantly depending on the stiffness of nuclear EoS. Generally, the SASI activity occurs more vigorously in models with softer EoS. By evaluating the gravitational-wave (GW) emission, we find a new GW signature on top of the previously identified one, in which the typical GW frequency increases with time due to an accumulating accretion to the proto-neutron star (PNS). The newly observed quasi-periodic signal appears in the frequency range from ˜100 to 200 Hz and persists for ˜150 ms before neutrino-driven convection dominates over the SASI. By analyzing the cycle frequency of the SASI sloshing and spiral modes as well as the mass accretion rate to the emission region, we show that the SASI frequency is correlated with the GW frequency. This is because the SASI-induced temporary perturbed mass accretion strikes the PNS surface, leading to the quasi-periodic GW emission. Our results show that the GW signal, which could be a smoking-gun signature of the SASI, is within the detection limits of LIGO, advanced Virgo, and KAGRA for Galactic events.

  19. Commercialization of an S-band standing-wave electron accelerator for industrial applications

    Science.gov (United States)

    Moon, Jin-Hyeok; Kwak, Gyeong-Il; Han, Jae-Ik; Lee, Gyu-Baek; Jeon, Seong-Hwan; Kim, Jae-Young; Hwang, Cheol-Bin; Lee, Gi-Yong; Kim, Young-Man; Park, Sung-Ju

    2016-09-01

    An electron accelerator system has been developed for use in industrial, as well as possible medical, applications. Based on our experiences achieved during prototype system development and various electron beam acceleration tests, we have built a stable and compact system for sales purposes. We have integrated a self-developed accelerating cavity, an E-gun pulse driver, a radio-frequency (RF) power system, a vacuum system, a cooling system, etc. into a frame with a size of 1800 × 1000 × 1500 mm3. The accelerating structure is a side-coupled standing-wave type operating in the π/2 mode (tuned to~3 GHz). The RF power is provided by using a magnetron driven by a solid-state modulator. The electron gun is a triode type with a dispenser cathode (diameter of 11 mm). The system is capable of delivering a maximum 900-W average electron beam power with tight focusing at the target. Until now, we have performed various electron beam tests and X-ray beam tests after having built the system, have completed the beam assessment for commercializations, and have been preparing full-fledged sales activity. This article reports on our system development processes and on some of our early test results for commercializations.

  20. Square-Wave Voltage Injection Algorithm for PMSM Position Sensorless Control With High Robustness to Voltage Errors

    DEFF Research Database (Denmark)

    Ni, Ronggang; Xu, Dianguo; Blaabjerg, Frede

    2017-01-01

    relationship with the magnetic field distortion. Position estimation errors caused by higher order harmonic inductances and voltage harmonics generated by the SVPWM are also discussed. Both simulations and experiments are carried out based on a commercial PMSM to verify the superiority of the proposed method...

  1. MICRO-MOTION EFFECT OF A TRAPPED ULTRA-COLD ION IN A STANDING-WAVE LASER

    Institute of Scientific and Technical Information of China (English)

    JIANG YU-RONG; FENG MANG; GAO KE-LIN; ZHU XI-WEN

    2001-01-01

    In the absence of the requirements of the Lamb-Dicke limit and rotating wave approximation, we semi-classically investigate the dynamics of a trapped ultra-cold ion in the standing-wave laser, with the consideration of the time- dependent potential and pseudo-potential of the Paul trap. The specific calculations show that the larger the Lamb-Dicke parameter η and the Rabi frequency Ω, the greater the difference between the dynamics in the time-dependent potential and the pseudo-potential.

  2. Orbital stability of standing waves of a class of fractional Schrödinger equations with Hartree-type nonlinearity

    KAUST Repository

    Cho, Yonggeun

    2016-05-04

    This paper is devoted to the mathematical analysis of a class of nonlinear fractional Schrödinger equations with a general Hartree-type integrand. We show the well-posedness of the associated Cauchy problem and prove the existence and stability of standing waves under suitable assumptions on the nonlinearity. Our proofs rely on a contraction argument in mixed functional spaces and the concentration-compactness method. © 2015 World Scientific Publishing Company

  3. Continuous sheathless microparticle and cell patterning using CL-SSAWs (conductive liquid-based standing surface acoustic waves)

    Science.gov (United States)

    Nam, Jeonghun; Kim, Jae Young; Lim, Chae Seung

    2017-01-01

    We present continuous, sheathless microparticle patterning using conductive liquid (CL)-based standing surface acoustic waves (SSAWs). Conventional metal electrodes patterned on a piezoelectric substrate were replaced with electrode channels filled with a CL. The device performance was evaluated with 5-μm fluorescent polystyrene particles at different flow rate and via phase shifting. In addition, our device was further applied to continuous concentration of malaria parasites at the sidewalls of the fluidic channel.

  4. Continuous sheathless microparticle and cell patterning using CL-SSAWs (conductive liquid-based standing surface acoustic waves

    Directory of Open Access Journals (Sweden)

    Jeonghun Nam

    2017-01-01

    Full Text Available We present continuous, sheathless microparticle patterning using conductive liquid (CL-based standing surface acoustic waves (SSAWs. Conventional metal electrodes patterned on a piezoelectric substrate were replaced with electrode channels filled with a CL. The device performance was evaluated with 5-μm fluorescent polystyrene particles at different flow rate and via phase shifting. In addition, our device was further applied to continuous concentration of malaria parasites at the sidewalls of the fluidic channel.

  5. Speedy standing wave design, optimization, and scaling rules of simulated moving bed systems with linear isotherms.

    Science.gov (United States)

    Weeden, George S; Wang, Nien-Hwa Linda

    2017-04-14

    Simulated Moving Bed (SMB) systems with linear adsorption isotherms have been used for many different separations, including large-scale sugar separations. While SMBs are much more efficient than batch operations, they are not widely used for large-scale production because there are two key barriers. The methods for design, optimization, and scale-up are complex for non-ideal systems. The Speedy Standing Wave Design (SSWD) is developed here to reduce these barriers. The productivity (PR) and the solvent efficiency (F/D) are explicitly related to seven material properties and 13 design parameters. For diffusion-controlled systems, the maximum PR or F/D is controlled by two key dimensionless material properties, the selectivity (α) and the effective diffusivity ratio (η), and two key dimensionless design parameters, the ratios of step time/diffusion time and pressure-limited convection time/diffusion time. The optimum column configuration for maximum PR or F/D is controlled by the weighted diffusivity ratio (η/α(2)). In general, high α and low η/α(2) favor high PR and F/D. The productivity is proportional to the ratio of the feed concentration to the diffusion time. Small particles and high diffusivities favor high productivity, but do not affect solvent efficiency. Simple scaling rules are derived from the two key dimensionless design parameters. The separation of acetic acid from glucose in biomass hydrolysate is used as an example to show how the productivity and the solvent efficiency are affected by the key dimensionless material and design parameters. Ten design parameters are optimized for maximum PR or minimum cost in one minute on a laptop computer. If the material properties are the same for different particle sizes and the dimensionless groups are kept constant, then lab-scale testing consumes less materials and can be done four times faster using particles with half the particle size. Copyright © 2017 Elsevier B.V. All rights reserved.

  6. Square wave series voltage compensator with high frequency DC-DC converter; Compensador serie de tensao em onda quadrada com conversor CC-CC de alta frequencia

    Energy Technology Data Exchange (ETDEWEB)

    Moreira, Angelo Roberto Rodrigues Resende; Caetano, William Douglas; Pires, Igor Amariz; Silva, Arlete Vieira da [Centro Universitario de Belo Horizonte (UnBH), MG (Brazil)], e-mails: angelogalo2005@hotmail.com, wdouglasbh@gmail.com, igor_amariz@yahoo.com.br, arlete.silva@prof.unibh.br

    2011-07-01

    The square wave series voltage compensator is an equipment used to mitigate voltage sags. In the case of occurrence of a voltage disturbance, the compensator acts generating a square wave voltage to supply the missing voltage. The energy inserted for the compensation is taken from the electrical grid, by a linear source. The purpose of this paper is to present a switching shunt converter instead of a linear one, with the same output parameters in order to increase the power density. This efficiency is demonstrated by simulations. (author)

  7. A sound nebula: the origin of the Solar System in the field of a standing sound wave

    CERN Document Server

    Beck, Svetlana

    2016-01-01

    According to the planetary origin conceptual model proposed in this paper, the protosun centre of the pre-solar nebula exploded, resulting in a shock wave that passed through it and then returned to the centre, generating a new explosion and shock wave. Recurrent explosions in the nebula resulted in a spherical standing sound wave, whose antinodes concentrated dust into rotating rings that transformed into planets. The extremely small angular momentum of the Sun and the tilt of its equatorial plane were caused by the asymmetry of the first, most powerful explosion. Differences between inner and outer planets are explained by the migration of solid matter, while the Oort cloud is explained by the division of the pre-solar nebula into a spherical internal nebula and an expanding spherical shell of gas. The proposed conceptual model can also explain the origin and evolution of exoplanetary systems and may be of use in searching for new planets.

  8. Standing Waves in an Elastic Spring: A Systematic Study by Video Analysis

    Science.gov (United States)

    Rodrigues Ventura, Daniel; Simeão de Carvalho, Paulo; Adriano Dias, Marco

    2017-01-01

    The word "wave" is part of the daily language of every student. However, the physical understanding of the concept demands a high level of abstract thought. In physics, waves are oscillating variations of a physical quantity that involve the transfer of energy from one point to another, without displacement of matter. A wave can be…

  9. Spherical Harmonics Reveal Standing EEG Waves and Long-Range Neural Synchronization during Non-REM Sleep

    Science.gov (United States)

    Sivakumar, Siddharth S.; Namath, Amalia G.; Galán, Roberto F.

    2016-01-01

    Previous work from our lab has demonstrated how the connectivity of brain circuits constrains the repertoire of activity patterns that those circuits can display. Specifically, we have shown that the principal components of spontaneous neural activity are uniquely determined by the underlying circuit connections, and that although the principal components do not uniquely resolve the circuit structure, they do reveal important features about it. Expanding upon this framework on a larger scale of neural dynamics, we have analyzed EEG data recorded with the standard 10–20 electrode system from 41 neurologically normal children and adolescents during stage 2, non-REM sleep. We show that the principal components of EEG spindles, or sigma waves (10–16 Hz), reveal non-propagating, standing waves in the form of spherical harmonics. We mathematically demonstrate that standing EEG waves exist when the spatial covariance and the Laplacian operator on the head's surface commute. This in turn implies that the covariance between two EEG channels decreases as the inverse of their relative distance; a relationship that we corroborate with empirical data. Using volume conduction theory, we then demonstrate that superficial current sources are more synchronized at larger distances, and determine the characteristic length of large-scale neural synchronization as 1.31 times the head radius, on average. Moreover, consistent with the hypothesis that EEG spindles are driven by thalamo-cortical rather than cortico-cortical loops, we also show that 8 additional patients with hypoplasia or complete agenesis of the corpus callosum, i.e., with deficient or no connectivity between cortical hemispheres, similarly exhibit standing EEG waves in the form of spherical harmonics. We conclude that spherical harmonics are a hallmark of spontaneous, large-scale synchronization of neural activity in the brain, which are associated with unconscious, light sleep. The analogy with spherical harmonics

  10. Growth and decay of discrete nonlinear Schrodinger breathers interacting with internal modes or standing-wave phonons

    Science.gov (United States)

    Johansson; Aubry

    2000-05-01

    We investigate the long-time evolution of weakly perturbed single-site breathers (localized stationary states) in the discrete nonlinear Schrodinger equation. The perturbations we consider correspond to time-periodic solutions of the linearized equations around the breather, and can be either (i) spatially localized or (ii) spatially extended. For case (i), which corresponds to the excitation of an internal mode of the breather, we find that the nonlinear interaction between the breather and its internal mode always leads to a slow growth of the breather amplitude and frequency. In case (ii), corresponding to interaction between the breather and a standing-wave phonon, the breather will grow provided that the wave vector of the phonon is such that the generation of radiating higher harmonics at the breather is possible. In other cases, breather decay is observed. This condition yields a limit value for the breather frequency above which no further growth is possible. We also discuss another mechanism for breather growth and destruction which becomes important when the amplitude of the perturbation is non-negligible, and which originates from the oscillatory instabilities of the nonlinear standing-wave phonons.

  11. A method to overcome the diffraction limit in infrared microscopy using standing waves in an attenuated total reflection configuration

    Science.gov (United States)

    Hendaoui, Nordine; Mani, Aladin; Liu, Ning; Tofail, Syed M.; Silien, Christophe; Peremans, André

    2017-01-01

    A method is proposed to overcome the diffraction limit of spatial resolution in infrared microscopy. To achieve this, standing waves in an attenuated total reflection configuration were generated to spatially modulate the absorbance of adsorbate vibrational transitions. A numerical simulation was undertaken. It showed that chemical imaging with a spatial resolution of approximately 100 nm is achievable in the case of self-assembled patterns (ofoctdecyltrichlorosilane [CH3-(CH2)17-SiCl3]), when probing the methyl modes located near 3.5 micrometres.

  12. Control of a large vacuum wave precursor on the SABRE voltage adder MITL and extraction ion diode

    Science.gov (United States)

    Cuneo, M. E.; Hanson, D. L.; Poukey, J. W.; Menge, P. R.; Savage, M. E.; Smith, J. R.; Bernard, M. A.

    SABRE is a ten-cavity magnetically insulated voltage adder (6MV, 300 kA) used to study ion beam production in high voltage extraction applied-B ion diodes. Observations indicate that the machine power initially propagates in a large-amplitude vacuum wave prior to electron emission. This vacuum wave 'precursor' has an important impact on the turn-on and impedance history of ion diodes. Some typical precursor characteristics are shown using transmission line, diode, and beam current and voltage data and are compared to TWOQUICK simulations. Two techniques are under investigation to control the precursor and its effects on diode performance. A plasma opening switch (POS) has been used to erode the precursor. Field enhancing inserts are also planned to decrease the macroscopic field required for electron emission from the cathode. This will limit the distance over which vacuum and insulated waves separate by propagation at different velocities. Experimental data from the POS technique and TWOQUICK simulations of the insert technique are presented and discussed.

  13. Predictive value of low tube voltage and dual-energy CT for successful shock wave lithotripsy: an in vitro study.

    Science.gov (United States)

    Largo, Remo; Stolzmann, Paul; Fankhauser, Christian D; Poyet, Cédric; Wolfsgruber, Pirmin; Sulser, Tullio; Alkadhi, Hatem; Winklhofer, Sebastian

    2016-06-01

    This study investigates the capabilities of low tube voltage computed tomography (CT) and dual-energy CT (DECT) for predicting successful shock wave lithotripsy (SWL) of urinary stones in vitro. A total of 33 urinary calculi (six different chemical compositions; mean size 6 ± 3 mm) were scanned using a dual-source CT machine with single- (120 kVp) and dual-energy settings (80/150, 100/150 Sn kVp) resulting in six different datasets. The attenuation (Hounsfield Units) of calculi was measured on single-energy CT images and the dual-energy indices (DEIs) were calculated from DECT acquisitions. Calculi underwent SWL and the number of shock waves for successful disintegration was recorded. The prediction of required shock waves regarding stone attenuation/DEI was calculated using regression analysis (adjusted for stone size and composition) and the correlation between CT attenuation/DEI and the number of shock waves was assessed for all datasets. The median number of shock waves for successful stone disintegration was 72 (interquartile range 30-361). CT attenuation/DEI of stones was a significant, independent predictor (P waves with the best prediction at 80 kVp (β estimate 0.576) (P waves ranged between ρ = 0.31 and 0.68 showing the best correlation at 80 kVp (P < 0.001). The attenuation of urinary stones at low tube voltage CT is the best predictor for successful stone disintegration, being independent of stone composition and size. DECT shows no added value for predicting the success of SWL.

  14. A stand-alone power system to integrate wind, wave and solar energy

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    @@ On 12 October, 2007, an agreement on the construction of a stand-alone renewable energy (RE) system at the Dangan Island was inked between the CAS Guangzhou Institute of Energy Conversion (GIEC) and the Wanshan Exemplary Marine Development Zone in Zhuhai, a coastal city in south China's Guangdong Province.

  15. An Experimental Study of Nonlinear Standing Waves in Resonators with Numerical Comparison

    Science.gov (United States)

    Finkbeiner, Joshua R.; Raman, Ganesh; Li, Xiaofan; Steinetz, Bruce M.; Daniels, Christopher; Huff, Dennis (Technical Monitor)

    2002-01-01

    Lawrenson et. al. [Journal of the Acoustic Society of America, Nov. 1998] described the generation of shock-free high-amplitude pressure waves in closed cavities using large equipment and resonators to produce the reported effects. An attempt is made to generate shock-free high-amplitude pressure waves using relatively small resonators. Ambient air is used as the working fluid. A small cylindrical resonator is tested resulting in the lack of a shocked waveform while a larger model of the same shape produces shock waves. A small conical resonator produces shock-free pressure waves at resonance, but the amplitude of these waves is small. A larger cone resonator model produces shock-free pressure waves of higher amplitude. A large horn-cone resonator also produces shock-free high amplitude pressure waves, A numerical model is used to compare the experimental results to theoretical results. The effects of structural resonances on the production of shock-free high-amplitude pressure waves are discussed, especially concerning difficulties encountered when these resonances were in the frequency ranges of interest. Identifying features of a structural resonance are presented.

  16. Communication: Development of standing evanescent-wave fluorescence correlation spectroscopy and its application to the lateral diffusion of lipids in a supported lipid bilayer

    Science.gov (United States)

    Otosu, Takuhiro; Yamaguchi, Shoichi

    2017-07-01

    We present standing evanescent-wave fluorescence correlation spectroscopy (SEW-FCS). This technique utilizes the interference of two evanescent waves which generates a standing evanescent-wave. Fringe-pattern illumination created by a standing evanescent-wave enables us to measure the diffusion coefficients of molecules with a super-resolution corresponding to one fringe width. Because the fringe width can be reliably estimated by a simple procedure, utilization of fringes is beneficial to quantitatively analyze the slow diffusion of molecules in a supported lipid bilayer (SLB), a model biomembrane formed on a solid substrate, with the timescale relevant for reliable FCS analysis. Furthermore, comparison of the data between SEW-FCS and conventional total-internal reflection FCS, which can also be performed by the SEW-FCS instrument, effectively eliminates the artifact due to afterpulsing of the photodiode detector. The versatility of SEW-FCS is demonstrated by its application to various SLBs.

  17. Investigation into the Effect of Acoustic Radiation Force and Acoustic Streaming on Particle Patterning in Acoustic Standing Wave Fields

    Directory of Open Access Journals (Sweden)

    Shilei Liu

    2017-07-01

    Full Text Available Acoustic standing waves have been widely used in trapping, patterning, and manipulating particles, whereas one barrier remains: the lack of understanding of force conditions on particles which mainly include acoustic radiation force (ARF and acoustic streaming (AS. In this paper, force conditions on micrometer size polystyrene microspheres in acoustic standing wave fields were investigated. The COMSOL® Mutiphysics particle tracing module was used to numerically simulate force conditions on various particles as a function of time. The velocity of particle movement was experimentally measured using particle imaging velocimetry (PIV. Through experimental and numerical simulation, the functions of ARF and AS in trapping and patterning were analyzed. It is shown that ARF is dominant in trapping and patterning large particles while the impact of AS increases rapidly with decreasing particle size. The combination of using both ARF and AS for medium size particles can obtain different patterns with only using ARF. Findings of the present study will aid the design of acoustic-driven microfluidic devices to increase the diversity of particle patterning.

  18. Two-dimensional standing wave total internal reflection fluorescence microscopy: superresolution imaging of single molecular and biological specimens.

    Science.gov (United States)

    Chung, Euiheon; Kim, Daekeun; Cui, Yan; Kim, Yang-Hyo; So, Peter T C

    2007-09-01

    The development of high resolution, high speed imaging techniques allows the study of dynamical processes in biological systems. Lateral resolution improvement of up to a factor of 2 has been achieved using structured illumination. In a total internal reflection fluorescence microscope, an evanescence excitation field is formed as light is total internally reflected at an interface between a high and a low index medium. The excitation region resulting in low background fluorescence. We present even higher resolution wide-field biological imaging by use of standing wave total internal reflection fluorescence (SW-TIRF). Evanescent standing wave (SW) illumination is used to generate a sinusoidal high spatial frequency fringe pattern on specimen for lateral resolution enhancement. To prevent thermal drift of the SW, novel detection and estimation of the SW phase with real-time feedback control is devised for the stabilization and control of the fringe phase. SW-TIRF is a wide-field superresolution technique with resolution better than a fifth of emission wavelength or approximately 100 nm lateral resolution. We demonstrate the performance of the SW-TIRF microscopy using one- and two-directional SW illumination with a biological sample of cellular actin cytoskeleton of mouse fibroblast cells as well as single semiconductor nanocrystal molecules. The results confirm the superior resolution of SW-TIRF in addition to the merit of a high signal/background ratio from TIRF microscopy.

  19. 方形薄板二维驻波的研究%Research of 2-dimensional standing waves in square plate

    Institute of Scientific and Technical Information of China (English)

    方奕忠; 王钢; 沈韩; 崔新图; 廖德驹; 冯饶慧

    2014-01-01

    通过对多种振源情形下的方形薄板二维驻波图形(克拉尼图形)的观测与研究,得到不同频率下驻波图形的波节数 n+1,m+1及波矢 k ,从而导出波速(相速)u 。实验结果与理论解析解(严格解)相比较符合得很好。%2-dimensional standing waves in square plates (Chladni figures) in several cases was studied both experimentally and theoretically .Wave nodes and wave vector of the standing wave fig-ures were gotten at different frequency ,and the wave velocity was deduced .The results of the experi-ment agreed well to the analytic solutions of theory .

  20. High-Precision Multi-Wave Rectifier Circuit Operating in Low Voltage + 1.5 Volt Current Mode

    Directory of Open Access Journals (Sweden)

    Bancha Burapattanasiri

    2009-12-01

    Full Text Available This article is present high-precision multi-wave rectifier circuit operating in low voltage +/- 1.5 Volt current modes by CMOS technology 0.5 μm, receive input and give output in current mode, respond at high frequency period. The structure compound with high-speed current comparator circuit, current mirror circuit, and CMOS inverter circuit. PSpice program used for confirmation the performance of testing. The PSpice program shows operating of circuit is able to working at maximum input current 400 μAp-p, maximum frequency responding 200 MHz, high precision and low power losses, and non-precision zero crossing output signal.Keywords-component; rectifier circuit; high-precision; low voltage; current mode;

  1. Flow under standing waves Part 2. Scour and deposition in front of breakwaters

    DEFF Research Database (Denmark)

    Gislason, Kjartan; Fredsøe, Jørgen; Sumer, B. Mutlu

    2009-01-01

    A 3-D general purpose Navier-Stokes solver was used to calculate the 2-D flow in front of the breakwater. The k-omega, SST (shear-stress transport) model was selected as the turbulence model. The morphologic model of the present code couples the flow solution with a sediment transport description...... and routines for, updating the computational mesh based on the mass balance of sediment. Laboratory experiments of scour also were conducted in a wave flume to obtain data for model verification. Both in the numerical simulations and in the laboratory experiment, two kinds of breakwaters were used: A vertical......-wall breakwater; and a sloping-wall breakwater (Slope: 1:1.5). Numerically obtained scour-deposition profiles were compared with the experiments. The numerical results show that the equilibrium scour depth normalized by the wave height decreases with increasing water-depth-to-wave-length ratio. Although...

  2. Parametric Study of Flow Patterns behind the Standing Accretion Shock Wave for Core-Collapse Supernovae

    CERN Document Server

    Iwakami, Wakana; Yamada, Shoichi

    2013-01-01

    The systematic research of flow patterns behind the accretion shock wave is conducted using three-dimensional hydrodynamics simulations for core-collapse supernovae in this study. Changing the accretion rate and neutrino luminosity, the steady solutions of the one-dimensional irrotational accretion flow passing through the spherical shock wave are evolved by imposing a random perturbation with 1% amplitude at the onset of the simulations. Depending on the accretion rate and neutrino luminosity, various flow patterns appear behind the shock wave. We classified them into the three fundamental flow patterns: (1) sloshing motion, (2) spiral motion, (3) multiple high-entropy bubbles, and the two anomalous flow patterns: (4) spiral motion with buoyant bubbles, and (5) spiral motion with pulsating rotational velocity. The sloshing and spiral motions tend to be dominant in the higher accretion rate and lower neutrino luminosity, and the generations of multiple buoyant bubbles tend to prevail in the lower accretion ra...

  3. Research on influence of high-voltage cable un-homogeneities on process of short waves distribution

    Energy Technology Data Exchange (ETDEWEB)

    Tirsu, M.; Berzan, V.; Rimschi, V. [Power Engineering Institute of Academy of Sciences of Moldova, 5 Academy Street, Kishinev (Moldova); Postolache, P. [University ' ' Politechnics' ' of Bucharest, Street Splaiul Independentei 313, Bucharest (Romania)

    2008-12-15

    The partial discharges (PDs) inside of high-voltage cable insulation negatively influence cable service lifespan. Therefore timely detection and localization of affected areas with the weakened electric insulation is a vital question, in particular - according to measured values of PD parameters before they reach the dangerous stage of their development. Electrical cable is a circuit with the distributed parameters for current and voltage waves, initiated by local PD which changes their starting values with time. These changes can be taken as informative parameters for solving problems of localization of the defect and evaluation of dangers to cable's performance. Clear and detailed understanding of PD pulse distribution features in power cables is the basis for correctly solving cable diagnostics tasks with non-destructive approaches. This article uses the mathematical model of a power cable on the premises of cable equations. The model allows for modeling of wave processes in a non-uniform electric circuit (at sudden change of longitudinal parameters) in view of repeated reflection of PD waves from the ends and un-homogeneities of an electric cable. Results of mathematical modeling were compared to the data received from physical model of 110 kV XLPE electric cable. The cable physical model is realized with the help of the chained circuit consisting of 15 quad-poles. This document shows results of measurements and modeling of wave process caused by PD. Also, details of the wave process as dependent on time and frequency, and practical use of measurements of PD for cable insulation control, are discussed. Practical measurements show high degree of accuracy with regards to the data generated by theoretical model analysis. (author)

  4. Nonlinear standing wave and acoustic streaming in an exponential-shape resonator by gas-kinetic scheme simulation

    Science.gov (United States)

    Zhang, Xiaoqing; Feng, Heying; Qu, Chengwu

    2016-10-01

    Nonlinear standing waves and acoustic streaming in an axial-symmetrical resonator with exponentially varying cross-sectional area were studied. A two-dimensional gas-kinetic Bhatnagar-Gross-Krook scheme based on the non-structure triangular grid was established to simulate nonlinear acoustic oscillations in the resonator. Details of the transient and steady flow fields and streaming were developed. The effects of winding index of the exponential-shape resonator, the displacement amplitude of the acoustic piston on the streaming, and the vortex pattern were analyzed. The results demonstrate that the acoustic streaming pattern in such resonators is different from the typical Rayleigh flow in a constant cross-sectional area resonator. No obvious shock wave appeared inside the exponential-shape resonator. The comparison reveals that with increasing the displacement amplitude of the acoustic piston energy dissipation is accompanied by vortex break-up from a first-level to a second-level transition, and even into turbulent flow. This research demonstrates that the exponential-shape resonator, especially that with a winding index of 2.2 exhibits better acoustic features and suppression effects on shock-wave, acoustic streaming, and the vortex.

  5. Influence of standing-wave electric field pattern on the laser damage resistance of HfO sub 2 thin films

    CERN Document Server

    Protopapa, M L; De Tomasi, F; Di Giulio, M; Perrone, M R; Scaglione, S

    2002-01-01

    The standing-wave electric field pattern that forms inside an optical coating as a consequence of laser irradiation is one of the factors influencing the coating laser-induced damage threshold. The influence of the standing-wave electric field profile on the damage resistance to ultraviolet radiation of hafnium dioxide (HfO sub 2) thin films was investigated in this work. To this end, HfO sub 2 thin films of different thicknesses deposited by the electron beam evaporation technique at the same deposition conditions were analyzed. Laser damage thresholds of the samples were measured at 308 nm (XeCl laser) by the photoacoustic beam deflection technique and microscopic inspections. The dependence of the laser damage threshold on the standing-wave electric field pattern was analyzed.

  6. Experimental Analysis on Subharmonic Standing Wave Vibrations in Lengthways Driven Strings%纵向驱动弦的次频振动实验分析

    Institute of Scientific and Technical Information of China (English)

    方天申

    2015-01-01

    讨论纵向驱动弦时的次频驻波振动现象,与弦运动轨迹的观察方法。根据弦运动轨迹,用仿真分析谐波振动可获得弦振动的有关物理信息。实验观察到,可出现非共振驻波(次频振动)振幅可比共振驻波振幅大的多现象。%It presents an experimental technique to observe the vibration tracks of string standing waves,and a subharmonic vibration of strings. The amplitude of a non-resonance subharmonic standing wave may be greater than that of a resonance standing wave in a longitudinally driven string.

  7. Investigation of sound field for a standing wave tube system with flow and with lateral Helmholtz resonator Ⅱ. Experiments and discussion

    Institute of Scientific and Technical Information of China (English)

    LI Song; LIU Ke; GUO Qing; HUANG Dongtao

    2005-01-01

    Based on the theoretical analysis of a standing wave tube with flow and lateral Helmholtz resonator, a relevant experimental apparatus were set up, and were successfully used to validate the the analysis above. Meanwhile an end correction and an equivalent radius coefficient covered in the theoretical analysis were also determined by experiments. Furthermore several results obtained from the theoretical analysis and experiments were used to discuss the effects of flow on the performance of Helmholtz resonator and the sound field in the standing wave tube. It is shown that using Helmholtz resonator for the standing wave tube with flow is still a good measure for noise reduction, even though the effect of noise reduction could be reduced because of flow.

  8. Multifrequency Compressional Magnetic Field Oscillations and Their Relation to Multiharmonic Toroidal Standing Alfvén Waves

    Science.gov (United States)

    Takahashi, K.; Waters, C. L.; Kletzing, C.; Kurth, W. S.; Smith, C. W.; Glassmeier, K. H.

    2015-12-01

    The power spectrum of the compressional component of magnetic field observed by the Van Allen Probes spacecraft near the magnetospheric equator in the dayside plasmasphere sometimes exhibits regularly spaced multiple peaks at frequencies below 50 mHz. We show by detailed analysis of events observed on two separate days in early 2014 that the frequencies change smoothly with the radial distance of the spacecraft and appear at or very near the frequencies of the odd harmonics of mutiharmonic toroidal standing Alfvén waves seen in the azimuthal component of the magnetic field. Even though the compressional component had low amplitude on one of the selected days, its spectral properties are highlighted by computing the ratio of the spectral powers of time series data obtained from spatially separated two Van Allen Probes spacecraft. The spectral similarity of the compressional and azimuthal components suggests that the compressional component contain field line resonance characteristics.

  9. Multifrequency compressional magnetic field oscillations and their relation to multiharmonic toroidal mode standing Alfvén waves

    Science.gov (United States)

    Takahashi, Kazue; Waters, Colin; Glassmeier, Karl-Heinz; Kletzing, Craig A.; Kurth, William S.; Smith, Charles W.

    2015-12-01

    The power spectrum of the compressional component of magnetic fields observed by the Van Allen Probes spacecraft near the magnetospheric equator in the dayside plasmasphere sometimes exhibits regularly spaced multiple peaks at frequencies below 50 mHz. We show by detailed analysis of events observed on two separate days in early 2014 that the frequencies change smoothly with the radial distance of the spacecraft and appear at or very near the frequencies of the odd harmonics of mutiharmonic toroidal mode standing Alfvén waves seen in the azimuthal component of the magnetic field. Even though the compressional component had a low amplitude on one of the selected days, its spectral properties are highlighted by computing the ratio of the spectral powers of time series data obtained from two spatially separated Van Allen Probes spacecraft. The spectral similarity of the compressional and azimuthal components suggests that the compressional component contains field line resonance characteristics.

  10. Design of cavities of a standing wave accelerating tube for a 6 MeV electron linear accelerator

    Directory of Open Access Journals (Sweden)

    S Zarei

    2017-08-01

    Full Text Available Side-coupled standing wave tubes in  mode are widely used in the low-energy electron linear accelerator, due to high accelerating gradient and low sensitivity to construction tolerances. The use of various simulation software for designing these kinds of tubes is very common nowadays. In this paper, SUPERFISH code and COMSOL are used for designing the accelerating and coupling cavities for a 6 MeV electron linear accelerator. Finite difference method in SUPERFISH code and Finite element method in COMSOL are used to solve the equations. Besides, dimension of accelerating and coupling cavities and also coupling iris dimension are optimized to achieve resonance frequency of 2.9985 MHz and coupling constant of 0.0112. Considering the results of this study and designing of the RF energy injection port subsequently, the construction of 6 MeV electron tube will be provided

  11. Particle dynamics and spatial $e^-e^+$ density structures at QED cascading in circularly polarized standing waves

    CERN Document Server

    Bashinov, A V; Kim, A V

    2016-01-01

    We present a comprehensive analysis of longitudinal particle drifting in a standing circularly polarized wave at extreme intensities when quantum radiation reaction (RR) effects should be accounted for. To get an insight into the physics of this phenomenon we made a comparative study considering the RR force in the Landau-Lifshitz or quantum-corrected form, including the case of photon emission stochasticity. It is shown that the cases of circular and linear polarization are qualitatively different. Moreover, specific features of particle dynamics have a strong impact on spatial structures of the electron-positron ($e^-e^+$) density created in vacuum through quantum electrodynamic (QED) cascades in counter-propagating laser pulses. 3D PIC modeling accounting for QED effects confirms realization of different pair plasma structures.

  12. Physical enviroment of 2-D animal cell aggregates formed in a short pathlength ultrasound standing wave trap.

    Science.gov (United States)

    Bazou, Despina; Kuznetsova, Larisa A; Coakley, W Terence

    2005-03-01

    2-D mammalian cell aggregates can be formed and levitated in a 1.5 MHz single half wavelength ultrasound standing wave trap. The physical environment of cells in such a trap has been examined. Attention was paid to parameters such as temperature, acoustic streaming, cavitation and intercellular forces. The extent to which these factors might be intrusive to a neural cell aggregate levitated in the trap was evaluated. Neural cells were exposed to ultrasound at a pressure amplitude of 0.54 MPa for 30 s; a small aggregate had been formed at the center of the trap. The pressure amplitude was then decreased to 0.27 MPa for 2 min, at which level the aggregation process continued at a slower rate. The pressure amplitude was then decreased to 0.06 MPa for 1 h. Temperature measurements that were conducted in situ with a 200 microm thermocouple over a 30 min period showed that the maximum temperature rise was less than 0.5 K. Acoustic streaming was measured by the particle image velocimetry method (PIV). It was shown that the hydrodynamic stress imposed on cells by acoustic streaming is less than that imposed by gentle preparative centrifugation procedures. Acoustic spectrum analysis showed that cavitation activity does not occur in the cell suspensions sonicated at the above pressures. White noise was detected only at a pressure amplitude of 1.96 MPa. Finally, it was shown that the attractive acoustic force between ultrasonically agglomerated cells is small compared with the normal attractive van der Waals force that operates at close cell surface separations. It is concluded that the standing wave trap operates only to concentrate cells locally, as in tissue, and does not modify the in vitro expression of surface receptor interactions.

  13. Mapping a plasmonic hologram with photosensitive polymer films: standing versus propagating waves.

    Science.gov (United States)

    Papke, Thomas; Yadavalli, Nataraja Sekhar; Henkel, Carsten; Santer, Svetlana

    2014-08-27

    We use a photosensitive layer containing azobenzene moieties to map near-field intensity patterns in the vicinity of nanogrids fabricated within a thin silver layer. It is known that azobenzene containing films deform permanently during irradiation, following the pattern of the field intensity. The photosensitive material reacts only to stationary waves whose intensity patterns do not change in time. In this study, we have found a periodic deformation above the silver film outside the nanostructure, even if the latter consists of just one groove. This is in contradiction to the widely accepted viewpoint that propagating surface plasmon modes dominate outside nanogrids. We explain our observation based on an electromagnetic hologram formed by the constructive interference between a propagating surface plasmon wave and the incident light. This hologram contains a stationary intensity and polarization grating that even appears in the absence of the polymer layer.

  14. Fabrication and Operation of Acoustofluidic Devices Supporting Bulk Acoustic Standing Waves for Sheathless Focusing of Particles

    OpenAIRE

    Shields, C. Wyatt; Cruz, Daniela F.; Ohiri, Korine A.; Yellen, Benjamin B.; Lopez, Gabriel P.

    2016-01-01

    Acoustophoresis refers to the displacement of suspended objects in response to directional forces from sound energy. Given that the suspended objects must be smaller than the incident wavelength of sound and the width of the fluidic channels are typically tens to hundreds of micrometers across, acoustofluidic devices typically use ultrasonic waves generated from a piezoelectric transducer pulsating at high frequencies (in the megahertz range). At characteristic frequencies that depend on the ...

  15. Instability analysis of resonant standing waves in a parametrically excited boxed basin

    Energy Technology Data Exchange (ETDEWEB)

    Sirwah, Magdy A [Department of Mathematics, Faculty of Science, Tanta University, Tanta (Egypt)], E-mail: magdysirwah@yahoo.com

    2009-06-15

    Two-mode parametric excited interfacial waves of incompressible immiscible liquids in an infinite boxed basin subjected to a vertical excitation are studied. The method of multiple time scales is used to obtain uniform solutions of the second-order system as well as the third-order one, which in turn leads to the solvability conditions of the two orders including the cubic interaction terms. The different cases of resonance that arise among the natural frequencies together with the frequency of the vertical vibration of the box are demonstrated theoretically and numerical computations of one of these cases (the two-to-one internal resonance and the principal parametric resonance) have been performed in detail in order to investigate the behavior of the resonant waves, especially the qualitative one. The autonomous system of four first-order differential equations for the modulation of the amplitudes and phases of the resonant waves is derived. Some numerical applications are achieved to show the stability criteria of the excited liquids inside the considered basin.

  16. Influence of voltage rise time on phase locking by priming effect in weakly resonant relativistic backward wave oscillators

    Science.gov (United States)

    Yang, Dewen; Deng, Yuqun; Teng, Yan; Shi, Yanchao; Wu, Ping; Chen, Changhua

    2017-05-01

    Phase locking is the key point of coherent power combination, which is very important for the development of high power microwave sources. In this paper, theoretical analysis and particle-in-cell simulations investigate the influence of the diode voltage rise time on phase locking by the priming effect in a weakly resonant relativistic backward wave oscillator (RBWO). When the diode voltage rise time becomes long and the final output frequency remains unchanged, the initial operation frequency may fluctuate around a value which is not equal to the final output frequency. Moreover, this state may last for several nanoseconds and then jumps to the final output frequency, which is very important for phase locking. Besides, it is suggested that, due to the weak resonance of the RF cavity without the electron beam, the microwave signal with frequency which is much lower than the final output frequency is usually excited at the beginning of the starting process. Finally, it is found that, when the injected frequency approaches the frequency of the initial microwave signal, the phase locking by the priming effect in the RBWO with long voltage rise time is noticeably improved, and the starting process becomes more rapid as well. The simulation results agree well with theoretical analysis.

  17. A New Phase-Shifted Cascade High Voltage Inverter

    Institute of Scientific and Technical Information of China (English)

    Lau Eng Tin

    2005-01-01

    This paper presents a unique novel design of the phase-shifted cascade high voltage inverter. Thehigh voltage inverter utilizes fewer power switches and supplies a balance load. The usage of phase shifttransformer and phase shifting SPWM ensures that input and output harmonic wave content is low and outputvoltage change (du/dt) has a low rate, meeting all the requirements of the power authorities. The most out-standing feature is the energy saving with very fast cost recovery.

  18. Fast acoustic streaming in standing waves: generation of an additional outer streaming cell.

    Science.gov (United States)

    Reyt, Ida; Daru, Virginie; Bailliet, Hélène; Moreau, Solène; Valière, Jean-Christophe; Baltean-Carlès, Diana; Weisman, Catherine

    2013-09-01

    Rayleigh streaming in a cylindrical acoustic standing waveguide is studied both experimentally and numerically for nonlinear Reynolds numbers from 1 to 30 [Re(NL)=(U0/c0)(2)(R/δν)(2), with U0 the acoustic velocity amplitude at the velocity antinode, c0 the speed of sound, R the tube radius, and δν the acoustic boundary layer thickness]. Streaming velocity is measured by means of laser Doppler velocimetry in a cylindrical resonator filled with air at atmospheric pressure at high intensity sound levels. The compressible Navier-Stokes equations are solved numerically with high resolution finite difference schemes. The resonator is excited by shaking it along the axis at imposed frequency. Results of measurements and of numerical calculation are compared with results given in the literature and with each other. As expected, the axial streaming velocity measured and calculated agrees reasonably well with the slow streaming theory for small ReNL but deviates significantly from such predictions for fast streaming (ReNL>1). Both experimental and numerical results show that when ReNL is increased, the center of the outer streaming cells are pushed toward the acoustic velocity nodes until counter-rotating additional vortices are generated near the acoustic velocity antinodes.

  19. The Standing Wave Phenomenon in Radio Telescopes; Frequency Modulation of the WSRT Primary Beam

    CERN Document Server

    Popping, Attila

    2007-01-01

    Inadequacies in the knowledge of the primary beam response of current interferometric arrays often form a limitation to the image fidelity. We hope to overcome these limitations by constructing a frequency-resolved, full-polarization empirical model for the primary beam of the Westerbork Synthesis Radio Telescope (WSRT). Holographic observations, sampling angular scales between about 5 arcmin and 11 degrees, were obtained of a bright compact source (3C147). These permitted measurement of voltage response patterns for seven of the fourteen telescopes in the array and allowed calculation of the mean cross-correlated power beam. Good sampling of the main-lobe, near-in, and far-side-lobes out to a radius of more than 5 degrees was obtained. A robust empirical beam model was detemined in all polarization products and at frequencies between 1322 and 1457 MHz with 1 MHz resolution. Substantial departures from axi-symmetry are apparent in the main-lobe as well as systematic differences between the polarization proper...

  20. Effect of standing-wave field distribution on femosecond laser-induced damage of HfO2/SiO2 mirror coating

    Institute of Scientific and Technical Information of China (English)

    Shunli Chen; Yuan'an Zhao; Hongbo He; Manda Shao

    2011-01-01

    Single-pulse and multi-pulse damage behaviors of "standard" (with A/4 stack structure) and "modified" (with reduced standing-wave field) HfO2/SiO2 mirror coatings are investigated using a commercial 50-fs, 800-nm Tksapphire laser system. Precise morphologies of damaged sites display strikingly different features when the samples are subjected to various number of incident pulses, which are explained reasonably by the standing-wave field distribution within the coatings. Meanwhile, the single-pulse laser-induced damage threshold of the "standard" mirror is improved by about 14% while suppressing the normalized electric field intensity at the outmost interface of the HfO2 and SiO2 layers by 37%. To discuss the damage mechanism, a theoretical model based on photoionization, avalanche ionization, and decays of electrons is adopted to simulate the evolution curves of the conduction-band electron density during pulse duration.%@@ Single-pulse and multi-pulse damage behaviors of "standard"(with λ/4 stack structure) and "modified"(with reduced standing-wave field) HfO2/SiO2 mirror coatings are investigated using a commercial 50-fs,800-nm Thsapphire laser system.以Precise morphologies of damaged sites display strikingly different features when the samples are subjected to various number of incident pulses, which are explained reasonably by the standing-wave field distribution within the coatings .

  1. Goos-Hänchen shift in a standing-wave-coupled electromagnetically-induced-transparency medium

    Science.gov (United States)

    Zhang, Xiao-Jun; Wang, Hai-Hua; Liang, Zhi-Peng; Xu, Yan; Fan, Cun-Bo; Liu, Cheng-Zhi; Gao, Jin-Yue

    2015-03-01

    The Goos-Hänchen shift of the system composed by two cavity walls and an intracavity atomic sample is presented. The atomic sample is treated as a four-level double-Λ system, driven by the two counterpropagating coupling fields. The probe field experiences the discontinuous refractive index variation and is reflected. Moreover, under the phase-matching condition, the four-wave mixing effect based on electromagnetically induced transparency can cause effective reflection. The Goos-Hänchen shifts appear in both situations and are carefully investigated in this article. We refer to the first one with the incident and reflected light having identical wavelength as the linear Goos-Hänchen shift, and the second one with the reflection wavelength determined by the phase-matching condition as the nonlinear Goos-Hänchen shift. The differences between the two kinds of shifts, such as the incident angle range, conditions for the shift peaks, and controllability, are discussed.

  2. Voltage-Controlled Square/Triangular Wave Generator with Current Conveyors and Switching Diodes

    Directory of Open Access Journals (Sweden)

    Martin Janecek

    2012-12-01

    Full Text Available A novel relaxation oscillator based on integrating the diode-switched currents and Schmitt trigger is presented. It is derived from a known circuit with operational amplifiers where these active elements were replaced by current conveyors. The circuit employs only grounded resistances and capacitance and is suitable for high frequency square and triangular signal generation. Its frequency can be linearly and accurately controlled by voltage that is applied to a high-impedance input. Computer simulation with a model of a manufactured conveyor prototype verifies theoretic assumptions.

  3. An interleaved structure for a high-voltage planar transformer for a Travelling-wave Tube

    DEFF Research Database (Denmark)

    Zhao, Bin; Wang, Gang; Hurley, William G.;

    2016-01-01

    is proposed to reduce leakage inductance and the insulation’s thickness is adjusted to optimize the electric isolation. In addition, the resistance and parasitic capacitance are investigated. With this method, a planar transformer used for a Travelling-Wave Tube Amplifier (TWTA) is designed. Calculations...

  4. Standing spin-wave mode structure and linewidth in partially disordered hexagonal arrays of perpendicularly magnetized sub-micron Permalloy discs

    Energy Technology Data Exchange (ETDEWEB)

    Ross, N., E-mail: rossn2282@gmail.com; Kostylev, M., E-mail: mikhail.kostylev@uwa.edu.au [School of Physics, University of Western Australia, Crawley, WA (Australia); Stamps, R. L. [School of Physics, University of Western Australia, Crawley, WA (Australia); SUPA School of Physics and Astronomy, University of Glasgow, Glasgow G12 8QQ (United Kingdom)

    2014-09-21

    Standing spin wave mode frequencies and linewidths in partially disordered perpendicular magnetized arrays of sub-micron Permalloy discs are measured using broadband ferromagnetic resonance and compared to analytical results from a single, isolated disc. The measured mode structure qualitatively reproduces the structure expected from the theory. Fitted demagnetizing parameters decrease with increasing array disorder. The frequency difference between the first and second radial modes is found to be higher in the measured array systems than predicted by theory for an isolated disc. The relative frequencies between successive spin wave modes are unaffected by reduction of the long-range ordering of discs in the array. An increase in standing spin wave resonance linewidth at low applied magnetic fields is observed and grows more severe with increased array disorder.

  5. MAGNETOHYDRODYNAMIC SEISMOLOGY OF A CORONAL LOOP SYSTEM BY THE FIRST TWO MODES OF STANDING KINK WAVES

    Energy Technology Data Exchange (ETDEWEB)

    Guo, Y.; Hao, Q.; Cheng, X.; Chen, P. F.; Ding, M. D. [School of Astronomy and Space Science and Key Laboratory of Modern Astronomy and Astrophysics in Ministry of Education, Nanjing University, Nanjing 210046 (China); Erdélyi, R. [Solar Physics and Space Plasma Research Center (SP2RC), School of Mathematics and Statistics, University of Sheffield, Sheffield S3 7RH (United Kingdom); Srivastava, A. K.; Dwivedi, B. N., E-mail: guoyang@nju.edu.cn [Department of Physics, Indian Institute of Technology (Banaras Hindu University), Varanasi 221005 (India)

    2015-02-01

    We report the observation of the first two harmonics of the horizontally polarized kink waves excited in a coronal loop system lying southeast of AR 11719 on 2013 April 11. The detected periods of the fundamental mode (P {sub 1}), its first overtone (P {sub 2}) in the northern half, and that in the southern one are 530.2 ± 13.3, 300.4 ± 27.7, and 334.7 ± 22.1 s, respectively. The periods of the first overtone in the two halves are the same considering uncertainties in the measurement. We estimate the average electron density, temperature, and length of the loop system as (5.1 ± 0.8) × 10{sup 8} cm{sup –3}, 0.65 ± 0.06 MK, and 203.8 ± 13.8 Mm, respectively. As a zeroth-order estimation, the magnetic field strength, B = 8.2 ± 1.0 G, derived by the coronal seismology using the fundamental kink mode matches with that derived by a potential field model. The extrapolation model also shows the asymmetric and nonuniform distribution of the magnetic field along the coronal loop. Using the amplitude profile distributions of both the fundamental mode and its first overtone, we observe that the antinode positions of both the fundamental mode and its first overtone shift toward the weak field region along the coronal loop. The results indicate that the density stratification and the temperature difference effects are larger than the magnetic field variation effect on the period ratio. On the other hand, the magnetic field variation has a greater effect on the eigenfunction of the first overtone than the density stratification does for this case.

  6. Analytical Formulation of Equatorial Standing Wave Phenomena: Application to QBO and ENSO

    Science.gov (United States)

    Pukite, P. R.

    2016-12-01

    inversion of the biennial mode lasting from 1980 to 1996. The parsimony of these analytical models arises from applying only known cyclic forcing terms to fundamental wave equation formulations. This raises the possibility that both QBO and ENSO can be predicted years in advance, apart from a metastable biennial phase inversion in ENSO.

  7. Ultra-Low Voltage Sixth-Order Low Pass Filter for Sensing the T-Wave Signal in ECGs

    Directory of Open Access Journals (Sweden)

    Panagiotis Bertsias

    2014-11-01

    Full Text Available An ultra-low voltage sixth-order low pass filter topology, suitable for sensing the T-wave signal in an electrocardiogram (ECG, is presented in this paper. This is realized using a cascade connection of second-order building blocks constructed from a sinh-domain two-integrator loop. The performance of the filter has been evaluated using the Cadence Analog Design Environment and the design kit provided by the Austria Mikro Systeme (AMS 0.35-µm CMOS process. The power consumption of filters was 7.21 nW, while a total harmonic distortion (THD level of 4% was observed for an input signal of 220 pA. The RMS value of the input referred noise was 0.43 pA, and the simulated value of the dynamic range (DR was 51.1 dB. A comparison with already published counterparts shows that the proposed topology offers the benefits of 0.5-V supply voltage operation and significantly improved power efficiency.

  8. Continuation of the development of a millimeter wave wideband tunable waveguide voltage controlled oscillator

    Science.gov (United States)

    Mascioli, A.

    1990-05-01

    A waveguide voltage controlled oscillator (VCO) was designed for use in the 26 GHz to 40 GHz range. The VCO uses a novel approach involving a double radial line concept to provide tuning bandwidths in excess of 3 GHz at these frequencies. The system was modelled via an equivalent circuit and the various parameters influencing performance, particularly the tuning range, were analyzed. Software simulation of the system was developed to predict the behavior of the circuit. The simulation package allows for verification of assumptions made during the development of the equivalent circuit. Results obtained from the simulation are in agreement with those obtained experimentally. The simulation also verified that the Gunn diode capacitance and resistance exist within a certain known range. Their exact values must be determined empirically.

  9. Standing-wave excited hard x-ray phototemission studies on a Au-sandwiched Fe/MgO interface

    Energy Technology Data Exchange (ETDEWEB)

    Doering, Sven; Keutner, Christoph; Schoenbohm, Frank; Berges, Ulf; Westphal, Carsten [DELTA/Experimentelle Physik I, TU Dortmund, Otto-Hahn-Str. 4, 44221 Dortmund (Germany); Buergler, Daniel E.; Schneider, Claus M. [IFF-9, Forschungszentrum Juelich, 52425 Juelich (Germany); Gorgoi, Mihaela; Schaefers, Franz [Helmholtzzentrum Berlin fuer Materialien und Energie, Albert Einstein Str. 15, 12489 Berlin (Germany)

    2011-07-01

    Magnetic tunnel junctions (MTJs) consisting of a thin layer-stack of Fe/MgO/Fe show a high tunnel-magneto resistance (TMR) ratio at room temperature. The strength of this effect is mainly driven by the interface and thus the Fe/MgO interface has been subject of many studies during the last years. Quite recently, calculations predicted an even higher TMR ratio for modified interfaces. In that work it was proposed that a monolayer of Au at the interface prevents the oxidation of the Fe-layer, and thus an increase of the TMR effect is expected. Up to now there is no experimental evidence that a well-defined Au monolayer can be prepared with the objective of preventing the Fe oxidation at the interface. In this work we studied a Au-modified interface with standing-wave excited hard X-ray photoemission. The goal of this study was the determination of the effective roughness of the Au layer. Our data-analysis shows that Au does not grow as a protective monolayer nor any hint of FeO formation was found.

  10. Impact of Acoustic Standing Waves on Structural Responses: Reverberant Acoustic Testing (RAT) vs. Direct Field Acoustic Testing (DFAT)

    Science.gov (United States)

    Kolaini, Ali R.; Doty, Benjamin; Chang, Zensheu

    2012-01-01

    Loudspeakers have been used for acoustic qualification of spacecraft, reflectors, solar panels, and other acoustically responsive structures for more than a decade. Limited measurements from some of the recent speaker tests used to qualify flight hardware have indicated significant spatial variation of the acoustic field within the test volume. Also structural responses have been reported to differ when similar tests were performed using reverberant chambers. To address the impact of non-uniform acoustic field on structural responses, a series of acoustic tests were performed using a flat panel and a 3-ft cylinder exposed to the field controlled by speakers and repeated in a reverberant chamber. The speaker testing was performed using multi-input-single-output (MISO) and multi-input-multi-output (MIMO) control schemes with and without the test articles. In this paper the spatial variation of the acoustic field due to acoustic standing waves and their impacts on the structural responses in RAT and DFAT (both using MISO and MIMO controls for DFAT) are discussed in some detail.

  11. X-ray standing wave simulations based on Fourier vector analysis as a method to retrieve complex molecular adsorption geometries

    Directory of Open Access Journals (Sweden)

    Giuseppe eMercurio

    2014-01-01

    Full Text Available We present an analysis method of normal incidence x-ray standing wave (NIXSW data that allows detailed adsorption geometries of complex molecules to be retrieved. This method (Fourier vector analysis is based on the comparison of both the coherence and phase of NIXSW data to NIXSW simulations of different molecular geometries as the relevant internal degrees of freedom are tuned. We introduce this analysis method using the prototypical molecular switch azobenzene (AB adsorbed on the Ag(111 surface as a model system. The application of the Fourier vector analysis to AB/Ag(111 provides, on the one hand, detailed adsorption geometries including dihedral angles, and on the other hand, insights into the dynamics of molecules and their bonding to the metal substrate. This analysis scheme is generally applicable to any adsorbate, it is necessary for molecules with potentially large distortions, and will be particularly valuable for molecules whose distortion on adsorption can be mapped on a limited number of internal degrees of freedom.

  12. Ultrahigh vacuum diffractometer for grazing-angle x-ray standing-wave experiments at a vertical-wiggler source

    Science.gov (United States)

    Sakata, O.; Hashizume, H.

    1995-02-01

    An ultrahigh vacuum (UHV) diffractometer has been designed for studies of surface structures using the grazing-angle x-ray standing-wave method. The design is featured by a horizontal plane of diffraction for use at a vertical-wiggler source of synchrotron radiation. A sample is horizontally mounted in an UHV chamber (4×10-7 Pa) placed on crossed swivels, which control the glancing-incidence angle of x rays on the sample surface with a 50-μrad accuracy. The chamber accepts a sample from a transportation vessel under high vacuum. A beryllium window allows x-ray fluorescence to reach a semiconductor detector at short access. The whole assembly sits on a high-precision rotary table, regulating the sample Δθ angle with a reproducibility of better than 0.5 μrad required for control of the x-ray field profile. The system has been successfully applied to an accurate determination of the in-plane ordering of As atoms on a Si(111) surface with a 1×1 structure.

  13. Analysis of Standing Waves on GPR Hyperbolic Travel-Time Responses - Case Studies in a Fractured Granitic Rock and a Deteriorating Coastal Structure

    Directory of Open Access Journals (Sweden)

    Yun-Li Chen

    2007-01-01

    Full Text Available Utilizing Ground Penetrating Radar (GPR, emitted electromagnetic (EM standing waves can be generated in underground voids. This phenomenon can be employed for the detection of subterranean voids and fractures when one has a proper understanding of relation between the widest inner length in an underground vacant space and half an EM wavelength. In this study, indoor and outdoor small-scale experiments verified the generation of EM standing waves. These responses were then applied in an arched-top cave covered by a single layer of backfill at Gongzihliao, Taiwan. Further studies were carried out at two other sites, including a fracture located in a granite mountain without regolith on the surface at Kinmen, and a deteriorating fishing port in Nanfangao, northeast Taiwan. Applying a band-pass filter with bandwidth narrower than a typical two-octave bandwidth produced the required standing waves with recognizable positions of minimum amplitude. A hyperbolic travel-time (HTT curve revealing the minimum amplitude, known as standing-wave nodes, indicates the presence of an underground hollow diffractor with the widest inner length in the vacant space being larger than half an EM wavelength. However, a HTT curve without nodal points signifies a hollow object with the widest inner length smaller than half an EM wavelength or an underground solid diffractor. An underground arched-top cave was detected by nodal points in the arc-like curves. When emitting the radar waves toward a wall, the interval of the nodes was used for estimating the wavelength of receiving GPR signals. Identifying the occurrence of nodal points in HTT or HTTlike curves in radargrams may assist the GPR interpreting work for underground tunnels, drainages, cavities, fractures, or solid objects.

  14. The Realization of Low Loop Voltage Start-up of HT-7 Tokamak Discharge with the Assistance of Lower Hybrid Wave

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    Low voltage start-up was realized in HT-7 discharges under the assistance of lower hybrid (LH) waves. The use of a strong LH wave, which can change its N// spectrum in a large range of several milliseconds, made the loop voltage for start-up reduce from around 20 V to less than 5 V. It means that the electric field for HT-7 start-up decreases from 2.5~3 V/m to 0.6 V/m.Some physical phenomena such as the consumption of magnetic flux in start-up phase and the radiation from the initial plasma were observed in this kind of low voltage start-up discharges.

  15. Radiation forces and torque on a rigid elliptical cylinder in acoustical plane progressive and (quasi)standing waves with arbitrary incidence

    CERN Document Server

    Mitri, F G

    2016-01-01

    Analytical expressions for the axial and transverse acoustic radiation forces as well as the radiation torque per length are derived for a rigid elliptical cylinder placed arbitrarily in the field of in plane progressive, quasi-standing or standing waves. The rigid elliptical cylinder case is important to be considered as a first-order approximation of the behavior of a fluid particle suspended in air, because of the significant acoustic impedance mismatch at the particle's boundary. Based on the partial-wave series expansion method in cylindrical coordinates, non-dimensional acoustic radiation force and torque functions are derived and defined in terms of the scattering coefficients of the elliptic cylinder. A coupled system of linear equations is obtained after applying the Neumann boundary condition for an immovable surface in a non-viscous fluid, and solved numerically by matrix inversion after performing a single numerical integration procedure. Computational results for the non-dimensional force compone...

  16. On revealing the vertical structure of nanoparticle films with elemental resolution: A total external reflection X-ray standing waves study

    Energy Technology Data Exchange (ETDEWEB)

    Zargham, Ardalan, E-mail: zargham@ifp.uni-bremen.d [Institute of Solid State Physics, University of Bremen, Otto-Hahn-Allee 1, 28359 Bremen (Germany); Schmidt, Thomas; Flege, Jan Ingo; Sauerbrey, Marc; Hildebrand, Radowan [Institute of Solid State Physics, University of Bremen, Otto-Hahn-Allee 1, 28359 Bremen (Germany); Roehe, Sarah; Baeumer, Marcus [Applied and Physical Chemistry, University of Bremen, Leobener Str. 2, 28359, Bremen (Germany); Falta, Jens [Institute of Solid State Physics, University of Bremen, Otto-Hahn-Allee 1, 28359 Bremen (Germany)

    2010-02-15

    We present a promising combination of methods to precisely determine the morphology of nanostructures, drawing on the example of monodisperse CoPt{sub 3} nanoparticle films deposited by spin coating and dip coating techniques on functionalized Au substrates. Ex-situ X-ray standing waves in total external reflection combined with X-ray reflectivity measurements were employed to determine element-specific atomic-density distributions in vertical direction.

  17. Sub-micron particle behaviour and capture at an immuno-sensor surface in an ultrasonic standing wave.

    Science.gov (United States)

    Kuznetsova, Larisa A; Martin, Stacey P; Coakley, W Terence

    2005-12-15

    The capture of 200 nm biotinylated latex beads from suspensions of concentration 10(7) to 2.5 x 10(8) particle/ml on an immuno-coated surface of the acoustic reflector in an ultrasound standing wave (USW) resonator has been studied while the acoustic pathlength was less than one half wavelength (lambda/2). The particles were delivered to the reflector's surface by acoustically induced flow. The capture dependencies on suspension concentration, duration of experiments and acoustic pressure have been established at 1.09, 1.46 and 1.75 MHz. Five-fold capture increase has been obtained at 1.75 MHz in comparison to the control (no ultrasound) situation. The contrasting behaviours of 1, 0.5 and 0.2 mum fluorescent latex beads in a lambda/4 USW resonator at 1.46 MHz have been characterized. The particle movements were observed with an epi-fluorescent microscope and the velocities of the particles were measured by particle image velocimetry (PIV). The experiments showed that whereas the trajectories of 1 mum particles were mainly affected by the direct radiation force, 0.5 mum particles were influenced both by the radiation force and acoustic streaming. The 0.2 mum latex beads followed acoustic streaming in the chamber and were not detectably affected by the radiation force. The streaming-associated behaviour of the 200 nm particles has implications for enhanced immunocapture of viruses and macromolecules (both of which are also too small to experience significant acoustic radiation force).

  18. Standing detonation wave engine

    KAUST Repository

    Kasimov, Aslan

    2015-10-08

    A detonation engine can detonate a mixture of fuel and oxidizer within a cylindrical detonation region to produce work. The detonation engine can have a first and a second inlet having ends fluidly connected from tanks to the detonation engine. The first and second inlets can be aligned along a common axis. The inlets can be connected to nozzles and a separator can be positioned between the nozzles and along the common axis.

  19. Surfing a Standing Wave

    Science.gov (United States)

    de Campos Valadares, Eduardo; Alves, Esdras Garcia

    2005-05-01

    Local "reversal of gravity" can be simulated with an inverted pendulum whose pivot is made to oscillate vertically. A beautiful demonstration of this surprising effect can be found in Ref. 1. In this case, the pendulum is a piece of plastic straw and its pivot pin is fixed at the end of a plastic ruler that is made to oscillate vertically by a small eccentric motor. A theoretical treatment of this inverted pendulum may be found in Ref. 2.

  20. Using rf voltage induced ferromagnetic resonance to study the spin-wave density of states and the Gilbert damping in perpendicularly magnetized disks

    Science.gov (United States)

    Devolder, Thibaut

    2017-09-01

    We study how the shape of the spin-wave resonance lines in rf voltage induced FMR can be used to extract the spin-wave density of states and the Gilbert damping within the precessing layer in nanoscale magnetic tunnel junctions that possess perpendicular magnetic anisotropy. We work with a field applied along the easy axis to preserve the cylindrical symmetry of the uniaxial perpendicularly magnetized systems. We first describe the experimental setup to study the susceptibility contributions of the spin waves in the field-frequency space. We then identify experimentally the maximum device size above which the spin waves confined in the free layer can no longer be studied in isolation as the linewidths of their discrete responses make them overlap into a continuous density of states. The rf voltage induced signal is the sum of two voltages that have comparable magnitudes: a first voltage that originates from the linear transverse susceptibility and rectification by magnetoresistance and a second voltage that arises from the nonlinear longitudinal susceptibility and the resultant time-averaged change of the exact micromagnetic configuration of the precessing layer. The transverse and longitudinal susceptibility signals have different dc bias dependencies such that they can be separated by measuring how the device rectifies the rf voltage at different dc bias voltages. The transverse and longitudinal susceptibility signals have different line shapes; their joint studies in both fixed field-variable frequency, or fixed frequency-variable field configurations can yield the Gilbert damping of the free layer of the device with a degree of confidence that compares well with standard ferromagnetic resonance. Our method is illustrated on FeCoB-based free layers in which the individual spin waves can be sufficiently resolved only for disk diameters below 200 nm. The resonance line shapes on devices with 90-nm diameters are consistent with a Gilbert damping of 0.011 . A single

  1. Continuous wave operation of distributed feedback quantum cascade lasers with low threshold voltage and low power consumption

    Science.gov (United States)

    Xie, Feng; Caneau, Catherine; LeBlanc, Herve P.; Coleman, Sean; Hughes, Lawrence C.; Zah, Chung-en

    2012-03-01

    We demonstrated the room temperature continuous wave (CW) operation of mid-infrared distributed feedback (DFB) quantum cascade lasers (QCLs) made of strain balanced GaInAs/AlInAs material on InP substrates for sensing CO2 isotope and N2O gas for potential applications that need battery powered portable devices in a sensor network. For the former device at 4.35 μm wavelength, we demonstrated a low threshold voltage of less than 8 V for battery operation and a near circular far field pattern with small divergent angles of 33 by 28 degrees full width at half maximum (FWHM) in vertical and horizontal directions, respectively, for easy collimation. For the latter device at 4.5 μm wavelength, we demonstrated a low CW threshold power consumption of 0.7 W at 20 °C. A side mode suppression ratio (SMSR) of 30 dB was achieved within the whole operating current and temperature ranges for both lasers.

  2. Self-action of propagating and standing Lamb waves in the plates exhibiting hysteretic nonlinearity: Nonlinear zero-group velocity modes.

    Science.gov (United States)

    Gusev, Vitalyi E; Lomonosov, Alexey M; Ni, Chenyin; Shen, Zhonghua

    2017-09-01

    An analytical theory accounting for the influence of hysteretic nonlinearity of micro-inhomogeneous plate material on the Lamb waves near the S1 zero group velocity point is developed. The theory predicts that the main effect of the hysteretic quadratic nonlinearity consists in the modification of the frequency and the induced absorption of the Lamb modes. The effects of the nonlinear self-action in the propagating and standing Lamb waves are expected to be, respectively, nearly twice and three times stronger than those in the plane propagating acoustic waves. The theory is restricted to the simplest hysteretic nonlinearity, which is influencing only one of the Lamé moduli of the materials. However, possible extensions of the theory to the cases of more general hysteretic nonlinearities are discussed as well as the perspectives of its experimental testing. Applications include nondestructive evaluation of micro-inhomogeneous and cracked plates. Copyright © 2017 Elsevier B.V. All rights reserved.

  3. Miniature Fourier transform spectrometer based on wavelength dependence of half-wave voltage of a LiNbO₃ waveguide interferometer.

    Science.gov (United States)

    Li, Jinyang; Lu, Dan-feng; Qi, Zhi-mei

    2014-07-01

    A simple and reliable spectrum-retrieval method was proposed for the development of miniature stationary Fourier transform (FT) spectrometers based on a LiNbO₃ (LN) waveguide Mach-Zehnder interferometer (MZI) modulator. The method takes into account the wavelength dependence of the optical pathlength difference (OPD) and allows us to use a nonlinear voltage ramp to modulate the OPD. The method is based on the dispersion of the half-wave voltage, which was measured to be a monotonous polynomial function of the wavelength for the LN waveguide MZI used. With the measured dispersion of the half-wave voltage, the OPD, as a linear function of the modulating voltage, can be accurately determined at each wavelength in the near-infrared region in which the MZI used is a single-mode device. A prototype FT spectrometer was prepared using a LN waveguide MZI modulator based on the above method. The experimental results demonstrated that the spectrometer can be used for accurate determination of the laser wavelength and for liquid absorptiometry.

  4. Analysis of Vibrating String Standing Wave Formed by Origin%利用Origin分析弦振动形成驻波的规律

    Institute of Scientific and Technical Information of China (English)

    李生仁; 白琼燕; 杨军; 李春望

    2014-01-01

    In this paper, analyzing the movement of the tiny sport on string section through wave equation in theory, deriving the relationship among the wavelength, the string tension, frequency and the density of strings when standing wave forms. Meanwhile, with evenly string vibration tester XZDY-type B, obtaining a lot of experimental data. And processing the data under the environment of Origin fitting processing system, making the data relationship chart to enable experimental data vis-ualization and informationization, the law that formed standing wave audio-visual and easier to understand.%本文通过波动方程和对弦上某一微小段的运动理论分析,推导出弦振动形成驻波时波长、弦中张力、频率和弦线密度之间的关系。同时借助XZDY-B型均匀弦振动仪,获得大量的实验数据,并在Origin环境下对数据进行系统的拟合处理,做出了数据间的关系图,使实验数据可视化和信息化,使弦振动形成驻波的规律更为直观,更容易理解。

  5. Analysis of the Tesla transformer operation at the first half-wave of the output voltage taking into account ohmic losses

    Science.gov (United States)

    Palchikov, E. I.; Ryabchun, A. M.

    2016-06-01

    The speed and efficiency of the Tesla transformer at the first half-wave of the output voltage are studied as a function of the Q factors of the circuits and their coupling factor. Calculated results and experimental data are considered. It is shown that for given Q factors, there is an optimal value of the coupling factor providing the highest efficiency, which can be calculated and for which designers should work.

  6. Study of molecule-metal interfaces by means of the normal incidence X-ray standing wave technique

    Energy Technology Data Exchange (ETDEWEB)

    Mercurio, Giuseppe

    2012-07-01

    Functional surfaces based on monolayers of organic molecules are currently subject of an intense research effort due to their applications in molecular electronics, sensing and catalysis. Because of the strong dependence of organic based devices on the local properties of the molecule-metal interface, a direct investigation of the interface chemistry is of paramount importance. In this context, the bonding distance, measured by means of the normal incidence X-ray standing wave technique (NIXSW), provides a direct access to the molecule-metal interactions. At the same time, NIXSW adsorption heights are used to benchmark different density functional theory (DFT) schemes and determine the ones with predictive power for similar systems. This work investigates the geometric and chemical properties of different molecule/metal interfaces, relevant to molecular electronics and functional surfaces applications, primarily by means of the NIXSW technique. All NIXSW data are analyzed with the newly developed open source program Torricelli, which is thoroughly documented in the thesis. In order to elucidate the role played by the substrate within molecule/metal interfaces, the prototype organic molecule 3,4,9,10-perylene-tetracarboxylic-dianhydride (PTCDA) is explored on the Ag(110) surface. The molecule results more distorted and at smaller bonding distances on the more reactive Ag(110) surface, in comparison with the Ag(100), the Ag(111) and Au(111) substrates. This conclusion follows from the detailed molecular adsorption geometry obtained from the differential analysis of nonequivalent carbon and oxygen species (including a careful error analysis). Subsequently, the chemisorptive PTCDA/Ag(110) interaction is tuned by the co-deposition of an external alkali metal, namely K. As a consequence, the functional groups of PTCDA unbind from the surface, which, in turn, undergoes major reconstruction. In fact, the resulting nanopatterned surface consists of alternated up and down

  7. Simultaneous analysis of Grazing Incidence X-Ray reflectivity and X-ray standing waves from periodic multilayer systems

    NARCIS (Netherlands)

    Yakunin, S.N.; Makhotkin, I.; Chuyev, M.A.; Seregin, A.Y.; Pashayev, E.M.; Louis, E.; Kruijs, van de R.W.E.; Bijkerk, F.; Kovalchuk, M.V.

    2012-01-01

    Structural analysis of periodic multilayers with small period thickness (~4 nm) is a challenging task, especially when thicknesses of intermixed interfaces become comparable to individual layer thicknesses. In general, angular dependent X-ray fluorescence measurements, excited by the X-ray standing

  8. Standing surface acoustic waves in LiNbO3 studied by time resolved X-ray diffraction at Petra III

    Directory of Open Access Journals (Sweden)

    T. Reusch

    2013-07-01

    Full Text Available We have carried out time resolved stroboscopic diffraction experiments on standing surface acoustic waves (SAWs of Rayleigh type on a LiNbO3 substrate. A novel timing system has been developed and commissioned at the storage ring Petra III of Desy, allowing for phase locked stroboscopic diffraction experiments applicable to a broad range of timescales and experimental conditions. The combination of atomic structural resolution with temporal resolution on the picosecond time scale allows for the observation of the atomistic displacements for each time (or phase point within the SAW period. A seamless transition between dynamical and kinematic scattering regimes as a function of the instantaneous surface amplitude induced by the standing SAW is observed. The interpretation and control of the experiment, in particular disentangling the diffraction effects (kinematic to dynamical diffraction regime from possible non-linear surface effects is unambiguously enabled by the precise control of phase between the standing SAW and the synchrotron bunches. The example illustrates the great flexibility and universality of the presented timing system, opening up new opportunities for a broad range of time resolved experiments.

  9. Optimal Work Area Selection of Stand-alone Photovoltaic Generation System Under Constant-Voltage Operation Mode%独立光伏系统恒压工作模式下最优工作区的选择

    Institute of Scientific and Technical Information of China (English)

    侯世英; 殷忠宁; 薛原; 曾鹏

    2012-01-01

    独立光伏系统中,当光伏电池输出的电能超出蓄电池和负载所需时,系统会过渡到一种非常重要的工作模式,即恒压工作模式。恒压模式下,对应同一负载,光伏电池存在2个工作点,分别位于最大功率点的左侧和右侧,即光伏电池i-u特性曲线的电流源区和电压源区。对这2个不同工作区域内光伏系统的稳定性进行了分析,提出了相应的控制方式。首先对光伏电池进行线性化处理,推导出光伏电池的线性化等效模型,并建立了整个系统的数学建模,在频率域内对不同工作点处系统的稳定性进行了分析。结果表明,恒压工作模式下,独立光伏系统工作于光伏电池的电压源区时,具有更好的稳定性。搭建的仿真模型在时域内验证了上述分析结果的正确性。%In stand-alone photovoltaic (PV) generation system, when the electric energy output from PV cells exceeds the power demand of batteries and loads, the usual operation mode of PV generation system will be turned into a very important operation mode, i.e., the constant voltage mode. Under constant voltage operation mode of PV array, there are two working points for the same load, which locate at the left side and right side of the maximum power point of the PV array, i.e., the current source region and voltage source region of current-voltage characteristics of PV array. The stability of PV system in the two different working regions is analyzed and corresponding control strategies are proposed. Firstly, the linearization of PV array is performed to derive the linearized equivalent model and to build the mathematical model of the whole system, then the stability of PV system at different working points is analyzed in the frequency domain. Analysis results show that under constant voltage operation mode, when stand-alone PV generation system works in the voltage source region of PV array the system is more stable

  10. Wave-like free-standing NiCo2O4 cathode for lithium-oxygen battery with high discharge capacity

    Science.gov (United States)

    Shen, Chen; Wen, Zhaoyin; Wang, Fan; Rui, Kun; Lu, Yan; Wu, Xiangwei

    2015-10-01

    A novel free-standing air electrode for Li-O2 battery with a wave-like microstructure is designed and synthesized through a facile electrochemical deposition process. Interconnected NiCo2O4 nanosheets with planes grown almost parallel to the surface of Ni foam build up continues porous catalytic surface with open space for the growth of Li2O2 discharge product. Li-O2 battery with the synthesized cathode delivers a high discharge capacity of 7004 mAh g-1 at 40 mA g-1 with a charge potential lower than 3.6 V (vs. Li/Li+), and significantly lower impedance compared to conventional electrode. Flower-like Li2O2 particles with a large size are observed as discharge products, consisting with the high discharge capacity. The unique wave-like microstructure and DMSO-based electrolyte with a high-doner-number are proposed to be responsible for the high discharge capacity, and the formation of large size Li2O2 discharge products. In addition, the electrode also exhibits stable cycle performance up to 100 cycles at the current density of 100 mA g-1 due to the robust composition and microstructure of the free-standing design.

  11. Electronic standing waves on the surface of Bi{sub 2}Sr{sub 2}CaCu{sub 2}O{sub 8+{delta}}

    Energy Technology Data Exchange (ETDEWEB)

    Vershinin, M.; Misra, S.; Abe, Y.; Ono, S.; Ando, Y.; Yazdani, A

    2004-08-01

    Scanning tunneling microscopy (STM) measurements have shown that electronic states at the surface of Bi{sub 2}Sr{sub 2}CaCu{sub 2}O{sub 8+{delta}} single crystals form standing wave patterns at temperatures far below the superconducting transition. It has been shown that these patterns are consistent with those expected from the interference of well-defined quasi-particles around the Bi{sub 2}Sr{sub 2}CaCu{sub 2}O{sub 8+{delta}} Fermi surface. We have extended STM measurements of these standing wave patterns to higher temperatures and have found that four unit-cell periodicity patterns observed in the superconducting state persist well above T{sub C}, in the pseudogap state. In this regime, many different experimental studies of the cuprates have long claimed the absence of well-defined quasi-particles. If the pseudogap regime is indeed devoid of any coherent quasi-particles then our results suggest that other phenomena, such as stripe formation, must play a role in formation of these patterns.

  12. W-waveform Standing Surface Acoustic Waves with Two Equilibrium Positions under Linear Phase Modulation for Patterning Microparticles into Alternate Grid Patterns

    CERN Document Server

    Lee, Junseok

    2016-01-01

    This paper presents W-waveform Standing Surface Acoustic Waves (W-SSAW), and as its application, patterning of two groups of microparticles with different sizes alternately without fixing firstly patterned particles. W-SSAW is constructed by two standing surface acoustic waves of frequencies $f$ and $2f$. Combined with linear phase modulation to translate Gor'kov potential at a constant speed, W-SSAW can selectively trap particles. The trapped particles follow the moving Gor'kov potential maintaining force equilibrium between Stokes' drag and the radiation force by W-SSAW. There exist two asymmetric equilibrium positions every period, and by the asymmetry, each group of particles is trapped at different equilibrium positions to form an alternate pattern. This technique is extended to two-dimensional alternate patterning by maintaining phase difference $90^\\circ$ between X- and Y-directional W-SSAWs. The patterning method utilizing W-SSAW is advantageous over SSAW-based patterning in that it does not require t...

  13. A supercell, Bloch wave method for calculating low-energy electron reflectivity with applications to free-standing graphene and molybdenum disulfide

    Science.gov (United States)

    McClain, John

    This dissertation reports on a novel theoretical and computational framework for calculating low-energy electron reflectivities from crystalline surfaces and its application to two layered systems of two-dimensional materials, graphene and molybdenum disulfide. The framework provides a simple and efficient approach through the matching of a small set of Fourier components of Bloch wave solutions to the Schrodinger Equation in a slab-in-supercell geometry to incoming and outgoing plane waves on both sides of the supercell. The implementation of this method is described in detail for the calculation of reflectivities in the lowest energy range, for which only specular reflection is allowed. This implementation includes the calculation of reflectivities from beams with normal or off-normal incidence. Two different algorithms are described in the case of off-normal incidence which differ in their dependence on the existence of a symmetry with a mirror plane parallel to the crystal surface. Applications to model potentials in one, two, and three dimensions display consistent results when using different supercell sizes and convergent results with the density of Fourier grids. The design of the Bloch wave matching also allows for the accurate modeling of crystalline slabs through the use of realistic potentials determined via density functional theory. The application of the method to low-energy electron scattering from free-standing systems of a few layers of graphene, including the use of these realistic potentials, demonstrates this ability of the method to accurately model real systems. It reproduces the layer-dependent oscillations found in experimental, normal incidence reflectivity curves for a few layers of graphene grown on silicon carbide. The normal incidence reflectivity curves calculated for slabs consisting of few-layer graphene on 10 layers of nickel show some qualitative agreement with experiment. General incidence reflectivity spectra for free-standing

  14. Digital measurement system for the LHC klystron high voltage modulator.

    CERN Document Server

    Mikkelsen, Anders

    Accelerating voltage in the Large Hadron Collider (LHC) is created by a means of 16 superconducting standing wave RF cavities, each fed by a 400MHz/300kW continuous wave klystron amplifier. Part of the upgrade program for the LHC long shutdown one is to replace the obsolete analogue current and voltage measurement circuitry located in the high voltage bunkers by a new, digital system, using ADCs and optical fibres. A digital measurement card is implemented and integrated into the current HV modulator oil tank (floating at -58kV) and interfaced to the existing digital VME boards collecting the data for several klystrons at the ground potential. Measured signals are stored for the logging, diagnostics and post-mortem analysis purposes.

  15. Investigation of standing-wave formation in a human skull for a clinical prototype of a large-aperture, transcranial MR-guided focused ultrasound (MRgFUS) phased array: an experimental and simulation study.

    Science.gov (United States)

    Song, Junho; Pulkkinen, Aki; Huang, Yuexi; Hynynen, Kullervo

    2012-02-01

    Standing-wave formation in an ex vivo human skull was investigated using a clinical prototype of a 30-cm diameter with 15-cm radius of curvature, low-frequency (230 kHz), hemispherical transcranial magnetic resonance-guided focused ultrasound phased array. Experimental and simulation studies were conducted with changing aperture size and f -number configurations of the phased array and qualitatively and quantitatively examined the acoustic pressure variation at the focus due to standing waves. The results demonstrated that the nodes and antinodes of standing wave produced by the small-aperture array were clearly seen at approximately every 3 mm. The effect of the standing wave became more pronounced as the focus was moved closer to skull base. However, a sharp focus was seen for the full array, and there was no such standing-wave pattern in the acoustic plane or near the skull base. This study showed that the fluctuation pressure amplitude would be greatly reduced by using a large-scale, hemispherical phased array with a low f-number.

  16. High-speed camera observation of multi-component droplet coagulation in an ultrasonic standing wave field

    Science.gov (United States)

    Reißenweber, Marina; Krempel, Sandro; Lindner, Gerhard

    2013-12-01

    With an acoustic levitator small particles can be aggregated near the nodes of a standing pressure field. Furthermore it is possible to atomize liquids on a vibrating surface. We used a combination of both mechanisms and atomized several liquids simultaneously, consecutively and emulsified in the ultrasonic field. Using a high-speed camera we observed the coagulation of the spray droplets into single large levitated droplets resolved in space and time. In case of subsequent atomization of two components the spray droplets of the second component were deposited on the surface of the previously coagulated droplet of the first component without mixing.

  17. Investigation of standing wave formation in a human skull for a clinical prototype of a large-aperture, transcranial MR-guided Focused Ultrasound (MRgFUS) phased array: An experimental and simulation study

    OpenAIRE

    Song, Junho; Pulkkinen, Aki; Huang, Yuexi; Hynynen, Kullervo

    2011-01-01

    Standing wave formation in an ex vivo human skull was investigated using a clinical prototype of a 30 cm diameter with 15 cm radius of curvature, low frequency (230 kHz), hemispherical transcranial Magnetic Resonance guided Focused Ultrasound (MRgFUS) phased-array. Experimental and simulation studies were conducted with changing aperture size and f-number configurations of the phased array, and qualitatively and quantitatively examined the acoustic pressure variation at the focus due to stand...

  18. A 12 GHz 30 mW 130 nm CMOS Rotary Travelling Wave Voltage Controlled Oscillator

    Directory of Open Access Journals (Sweden)

    G. Jacquemod

    2012-01-01

    Full Text Available This paper reports a 12 GHz rotary travelling wave (RTW voltage controlled oscillator designed in a 130 nm CMOS technology. The phase noise and power consumption performances were compared with the literature and with telecommunication standards for broadcast satellite applications. The RTW VCO exhibits a −106 dBc/Hz at 1 MHz and a 30 mW power consumption with a sensibility of 400 MHz/V. Finally, requirements are given for a PLL implementation of the RTW VCO and simulated results are presented.

  19. Radiation forces and torque on a rigid elliptical cylinder in acoustical plane progressive and (quasi)standing waves with arbitrary incidence

    Science.gov (United States)

    Mitri, F. G.

    2016-07-01

    This paper presents two key contributions; the first concerns the development of analytical expressions for the axial and transverse acoustic radiation forces exerted on a 2D rigid elliptical cylinder placed in the field of plane progressive, quasi-standing, or standing waves with arbitrary incidence. The second emphasis is on the acoustic radiation torque per length. The rigid elliptical cylinder case is important to be considered as a first-order approximation of the behavior of a cylindrical fluid column trapped in air because of the significant acoustic impedance mismatch at the particle boundary. Based on the rigorous partial-wave series expansion method in cylindrical coordinates, non-dimensional acoustic radiation force and torque functions are derived and defined in terms of the scattering coefficients of the elliptic cylinder. A coupled system of linear equations is obtained after applying the Neumann boundary condition for an immovable surface in a non-viscous fluid and solved numerically by matrix inversion after performing a single numerical integration procedure. Computational results for the non-dimensional force components and torque, showing the transition from the progressive to the (equi-amplitude) standing wave behavior, are performed with particular emphasis on the aspect ratio a/b, where a and b are the semi-axes of the ellipse, the dimensionless size parameter, as well as the angle of incidence ranging from end-on to broadside incidence. The results show that the elliptical geometry has a direct influence on the radiation force and torque, so that the standard theory for circular cylinders (at normal incidence) leads to significant miscalculations when the cylinder cross section becomes non-circular. Moreover, the elliptical cylinder experiences, in addition to the acoustic radiation force, a radiation torque that vanishes for the circular cylinder case. The application of the formalism presented here may be extended to other 2D surfaces of

  20. Continuously Phase-Modulated Standing Surface Acoustic Waves for Separation of Particles and Cells in Microfluidic Channels Containing Multiple Pressure Nodes

    CERN Document Server

    Lee, Junseok; Kang, Byungjun; Lee, Hyungsuk

    2016-01-01

    This paper describes continuously phase-modulated standing surface acoustic waves (CPM-SSAW) and its application for particle separation in multiple pressure nodes. A linear change of phase in CPM-SSAW applies a force to particles whose magnitude depends on their size and contrast factors. During continuous phase modulation, we demonstrate that particles with the target dimension are translated in the direction of moving pressure nodes, whereas smaller particles show oscillatory movements. The rate of phase modulation is optimized for separation of target particles from the relationship between mean particle velocity and period of oscillation. The developed technique is applied to separate particles of the target dimension from the particle mixture. Furthermore, we also demonstrate human keratinocyte cells can be separated in the cell and bead mixture. The separation technique is incorporated with a microfluidic channel spanning multiple pressure nodes, which is advantageous over separation in a single pressu...

  1. Synthesis of Linear Array of Parallel Dipole Antennas with Minimum Standing Wave Ratio Using Simulated Annealing and Particle Swarm Optimization approach

    Directory of Open Access Journals (Sweden)

    Banani Basu

    2010-05-01

    Full Text Available In this paper, we propose a technique based on two evolutionary algorithms simulated annealing and particle swarm optimization to design a linear array of half wavelength long parallel dipole antennas that will generate a pencil beam in the horizontal plane with minimum standing wave ratio (SWR and fixed side lobe level (SLL. Dynamic range ratio of current amplitude distribution is kept at a fixed value. Two different methods have been proposed withdifferent inter-element spacing but with same current amplitude distribution. First one uses a fixed geometry and optimizes the excitation distribution on it. In the second case further reduction of SWR is done via optimization of interelement spacing while keeping the amplitude distribution same as before. Coupling effect between the elements is analyzed using induced EMF method and minimized interms of SWR. Numerical results obtained from SA are validated by comparing with results obtained using PSO.

  2. Development of A New Waveguide Arc /Standing-wave Protecting Device%新型波导电弧/驻波保护装置的研制

    Institute of Scientific and Technical Information of China (English)

    钱锰

    2001-01-01

    The waveguide arc is one of the important reasons of damaging klystron. The practical block diagram , improvement circuit and relevant data of arc/standing-wave are given in this paper. The selection of the key device is analyzed. Finally, the experimental results and characteristic curve are also given.%波导电弧(俗称打火)/驻波过大是损坏速调管的重要原因之一。本文给出了电弧/驻波保护装置的实用框图、改进电路及有关数据,并对关键器件的选择进行了详细分析,最后给出了实验结果及特性曲线。

  3. Continuously phase-modulated standing surface acoustic waves for separation of particles and cells in microfluidic channels containing multiple pressure nodes

    Science.gov (United States)

    Lee, Junseok; Rhyou, Chanryeol; Kang, Byungjun; Lee, Hyungsuk

    2017-04-01

    This paper describes continuously phase-modulated standing surface acoustic waves (CPM-SSAW) and its application for particle separation in multiple pressure nodes. A linear change of phase in CPM-SSAW applies a force to particles whose magnitude depends on their size and contrast factors. During continuous phase modulation, we demonstrate that particles with a target dimension are translated in the direction of moving pressure nodes, whereas smaller particles show oscillatory movements. The rate of phase modulation is optimized for separation of target particles from the relationship between mean particle velocity and period of oscillation. The developed technique is applied to separate particles of a target dimension from the particle mixture. Furthermore, we also demonstrate human keratinocyte cells can be separated in the cell and bead mixture. The separation technique is incorporated with a microfluidic channel spanning multiple pressure nodes, which is advantageous over separation in a single pressure node in terms of throughput.

  4. Developments in the use and capability of millimetre wave technologies for stand-off detection of threat items over the last decade

    Science.gov (United States)

    Ollett, E.; Clark, A.

    2017-05-01

    The Home Office Centre for Applied Science and Technology (CAST) has a longstanding history in the evaluation of passive and active millimetre wave (mmW) systems for stand-off detection. The requirements for stand-off detection have evolved greatly over the last decade due to changes in threat, as has the capability of technologies. CAST has worked with these changes to evaluate systems alongside other government departments, developing expertise in the standard of technology from low to high technology readiness level (TRL) as well as understanding the limitations in detection. In this paper I discuss the work that has been undertaken by CAST since 2007, exploring the developments in methodology that have become necessary for trials to capture the requirements successfully. This involves utilising aspects of test protocols to ensure consistency across testing between CAST and other organisations, allowing for a fair comparison of data. The trials undertaken vary from evaluating the system capability in a static setting to the capability in a crowded environment such as a shopping centre. Understanding the performance capability of passive and active (mmW) systems in crowded places is particularly important given the current threat status of the UK.

  5. X-ray standing wave studies of strained InxGa1-xAs/InP short-period superlattices

    Science.gov (United States)

    Aruta, Carmela; Lamberti, Carlo; Gastaldi, Luigi; Boscherini, Federico

    2003-05-01

    We report an x-ray standing wave (XSW) study on a set of structurally well-characterized InxGa1-xAs/InP short-period superlattices grown by metal-organic chemical vapor deposition and chemical-beam epitaxy techniques. It was possible to model the x-ray standing wave profiles only once the superlattice period has been assumed to be constituted by four layers of well-defined chemical composition [barrier (InP), first interface (InAs0.7P0.3), well (In0.53Ga0.47As), and second interface (In0.53Ga0.47As0.7P0.3)], and of variable thickness. The thickness of the four layers have been obtained by fitting the high resolution x-ray diffraction profiles of the heterostructures. The presence of partially disordered interface layers, as evidenced by a transmission electron microscopy study, causes a significant reduction of the coherent fraction, F, of both Ga and As atoms. The difference in F values among measured samples illustrates how the XSW can provide important information on the quality of semiconductor superlattices. Comparison with a "long period (160 Å)" In0.53Ga0.47As/InP superlattice, where the role played by InAs0.7P0.3 and In0.53Ga0.47As0.7P0.3 interface layers is negligible, confirms this picture. The coherent fraction of both As and Ga correlates well with the average perpendicular lattice misfit determined by x-ray diffraction.

  6. 低压载波通讯测试仪的开发与应用%The Development and Application of the Low Voltage Carrier Wave Communication Tester

    Institute of Scientific and Technical Information of China (English)

    刘勇; 张明旭; 李贤伟; 李丹

    2014-01-01

    文章从原来集抄系统缺乏有效的现场调试方式和试验方法来分析原问题的所在,从原理上详细论述了低压载波通讯测试仪在低压集抄采集系统维护中的应用,这对我们的低压采集系统今后的维护工作十分重要。这项技术的推广可以使我们的集抄系统建设工作更加方便、快捷,使之能更好地为营销现代化工作服务。%In view of the problem that there is no effective field debugging method or testing method in the original e -lectricity data collection system, the paper detailedly and theoretically discussed the application of the low voltage car -rier wave communication tester to the maintenance of the low voltage data collection system .This will be of vital im-portance for the maintenance of the low voltage data collection system in the future .The promotion of the technology can make the construction of the data collection system more convenient and faster , and enable it to provide better service for the modernization of marketing.

  7. Drive Stands

    Data.gov (United States)

    Federal Laboratory Consortium — The Electrical Systems Laboratory (ESL)houses numerous electrically driven drive stands. A drive stand consists of an electric motor driving a gearbox and a mounting...

  8. Spatial proximity effects on the excitation of sheath RF voltages by evanescent slow waves in the ion cyclotron range of frequencies

    Science.gov (United States)

    Colas, Laurent; Lu, Ling-Feng; Křivská, Alena; Jacquot, Jonathan; Hillairet, Julien; Helou, Walid; Goniche, Marc; Heuraux, Stéphane; Faudot, Eric

    2017-02-01

    We investigate theoretically how sheath radio-frequency (RF) oscillations relate to the spatial structure of the near RF parallel electric field E ∥ emitted by ion cyclotron (IC) wave launchers. We use a simple model of slow wave (SW) evanescence coupled with direct current (DC) plasma biasing via sheath boundary conditions in a 3D parallelepiped filled with homogeneous cold magnetized plasma. Within a ‘wide-sheath’ asymptotic regime, valid for large-amplitude near RF fields, the RF part of this simple RF  +  DC model becomes linear: the sheath oscillating voltage V RF at open field line boundaries can be re-expressed as a linear combination of individual contributions by every emitting point in the input field map. SW evanescence makes individual contributions all the larger as the wave emission point is located closer to the sheath walls. The decay of |V RF| with the emission point/sheath poloidal distance involves the transverse SW evanescence length and the radial protrusion depth of lateral boundaries. The decay of |V RF| with the emitter/sheath parallel distance is quantified as a function of the parallel SW evanescence length and the parallel connection length of open magnetic field lines. For realistic geometries and target SOL plasmas, poloidal decay occurs over a few centimeters. Typical parallel decay lengths for |V RF| are found to be smaller than IC antenna parallel extension. Oscillating sheath voltages at IC antenna side limiters are therefore mainly sensitive to E ∥ emission by active or passive conducting elements near these limiters, as suggested by recent experimental observations. Parallel proximity effects could also explain why sheath oscillations persist with antisymmetric strap toroidal phasing, despite the parallel antisymmetry of the radiated field map. They could finally justify current attempts at reducing the RF fields induced near antenna boxes to attenuate sheath oscillations in their vicinity.

  9. Structural investigations of doped GaN-films with X-ray standing waves; Strukturelle Untersuchungen dotierter GaN-Filme mit stehenden Roentgenwellenfeldern

    Energy Technology Data Exchange (ETDEWEB)

    Siebert, M.

    2006-10-30

    In this thesis, the incorporation of Mg and Si in GaN-films grown on (0001)-sapphire substrates is investigated in detail by applying several synchrotron radiation techniques. The segregational behavior of Si and Mg is investigated by X-ray-photoelectron-spectroscopy (XPS) and XPS-microscopy. For the first time, it is revealed that also Si segregates to the surface and stabilizes surface facets along high-symmetry directions. Additionally, it is found that Mg also segregates to the crystal surface at concentrations far below the threshold condition for the formation of pyramidal defects. For the first time, the technique of X-ray standing waves (XSW), which allows to directly conclude on the crystal and defect structure on the atomic scale, is successfully applied to thick crystals with high defect density. In order to compensate for the high crystal mosaicity of GaN, which significantly reduces the accuracy of the XSW-measurements, the experiments were performed in near-backscattering geometry, as in this setup the intrinsic reflection width becomes large as compared to the tilt mosaicity. Influences of doped crystal material are suppressed by using a thick undoped high quality GaN-film for the formation of a standing wave field, which is used for the investigation of a thin doped film deposited on top. By performing the XSW measurements with probe signals of different surface sensitivity (fluorescence and photoelectrons) the incorporation behavior within the bulk crystal is compared to regions close to the surface. Within this thesis a technique is suggested that allows to determine the non-dipole contributions to the yield by comparing Auger electron and photoelectron secondary signals. The XSW-measurements on Si-doped samples reveal that Si is solely incorporated on substitutional Ga-sites both within the bulk crystal and close to the surface. In the bulk, Si is homogeneously distributed, distorting the crystal lattice in their vicinity. At the surface Si is

  10. Making use of x-ray optical effects in photoelectron-, Auger electron-, and x-ray emission spectroscopies: Total reflection, standing-wave excitation, and resonant effects

    Energy Technology Data Exchange (ETDEWEB)

    Yang, S.-H. [IBM Almaden Research Center, San Jose, California 95120 (United States); Gray, A. X. [Materials Sciences Division, Lawrence Berkeley National Laboratory, Berkeley, California 94740 (United States); Department of Physics, University of California at Davis, Davis, California 95616 (United States); Stanford Institute for Materials and Energy Science, Stanford University and SLAC National Accelerator Laboratory, Menlo Park, California 94025 (United States); Kaiser, A. M. [Materials Sciences Division, Lawrence Berkeley National Laboratory, Berkeley, California 94740 (United States); Department of Physics, University of California at Davis, Davis, California 95616 (United States); Peter Grunberg Institute, PGI-6, Forschungszentrum Juelich, 52425 Juelich (Germany); Mun, B. S. [Advanced Light Source, Lawrence Berkeley National Laboratory, Berkeley, California 94720 (United States); Department of Applied Physics, Hanyang University, Ansan, Gyeonggi 426-791 (Korea, Republic of); Sell, B. C. [Materials Sciences Division, Lawrence Berkeley National Laboratory, Berkeley, California 94740 (United States); Department of Physics, University of California at Davis, Davis, California 95616 (United States); Department of Physics, Otterbein College, Westerville, Ohio 43081 (United States); Kortright, J. B. [Materials Sciences Division, Lawrence Berkeley National Laboratory, Berkeley, California 94740 (United States); Fadley, C. S. [Materials Sciences Division, Lawrence Berkeley National Laboratory, Berkeley, California 94740 (United States); Department of Physics, University of California at Davis, Davis, California 95616 (United States)

    2013-02-21

    We present a general theoretical methodology and related open-access computer program for carrying out the calculation of photoelectron, Auger electron, and x-ray emission intensities in the presence of several x-ray optical effects, including total reflection at grazing incidence, excitation with standing-waves produced by reflection from synthetic multilayers and at core-level resonance conditions, and the use of variable polarization to produce magnetic circular dichroism. Calculations illustrating all of these effects are presented, including in some cases comparisons to experimental results. Sample types include both semi-infinite flat surfaces and arbitrary multilayer configurations, with interdiffusion/roughness at their interfaces. These x-ray optical effects can significantly alter observed photoelectron, Auger, and x-ray intensities, and in fact lead to several generally useful techniques for enhancing surface and buried-layer sensitivity, including layer-resolved densities of states and depth profiles of element-specific magnetization. The computer program used in this study should thus be useful for a broad range of studies in which x-ray optical effects are involved or are to be exploited in next-generation surface and interface studies of nanoscale systems.

  11. Stand Straight and Stand Tall

    Institute of Scientific and Technical Information of China (English)

    昝亚娟

    2007-01-01

    <正>My grandfather grew up in war-torn Europe.When German soldiers occupied his hometown,the thriving (繁荣的) city of Tarow,Poland,he refused to obey them and eventually joined the Soviet army to fight for his country’s freedom."Stand straight,stand tall,"he told himself.

  12. Role of calcium stores and membrane voltage in the generation of slow wave action potentials in guinea-pig gastric pylorus.

    Science.gov (United States)

    van Helden, D F; Imtiaz, M S; Nurgaliyeva, K; von der Weid, P; Dosen, P J

    2000-04-01

    1. Intracellular recordings made in single bundle strips of a visceral smooth muscle revealed rhythmic spontaneous membrane depolarizations termed slow waves (SWs). These exhibited 'pacemaker' and 'regenerative' components composed of summations of more elementary events termed spontaneous transient depolarizations (STDs). 2. STDs and SWs persisted in the presence of tetrodotoxin, nifedipine and ryanodine, and upon brief exposure to Ca2+-free Cd2+-containing solutions; they were enhanced by ACh and blocked by BAPTA AM, cyclopiazonic acid and caffeine. 3. SWs were also inhibited in heparin-loaded strips. SWs were observed over a wide range of membrane potentials (e.g. -80 to -45 mV) with increased frequencies at more depolarized potentials. 4. Regular spontaneous SW activity in this preparation began after 1-3 h superfusion of the tissue with physiological saline following the dissection procedure. Membrane depolarization applied before the onset of this activity induced bursts of STD-like events (termed the 'initial' response) which, when larger than threshold levels initiated regenerative responses. The combined initial-regenerative waveform was termed the SW-like action potential. 5. Voltage-induced responses exhibited large variable latencies (typical range 0.3-4 s), refractory periods of approximately 11 s and a pharmacology that was indistinguishable from those of STDs and spontaneous SWs. 6. The data indicate that SWs arise through more elementary inositol 1,4,5-trisphosphate (IP3) receptor-induced Ca2+ release events which rhythmically synchronize to trigger regenerative Ca2+ release and induce inward current across the plasmalemma. The finding that action potentials, which were indistinguishable from SWs, could be evoked by depolarization suggests that membrane potential modulates IP3 production. Voltage feedback on intracellular IP3-sensitive Ca2+ release is likely to have a major influence on the generation and propagation of SWs.

  13. Applications of passive remote surface acoustic wave sensors in high-voltage systems; Einsatz von passiven funkabfragbaren Oberflaechenwellensensoren in der elektrischen Energietechnik

    Energy Technology Data Exchange (ETDEWEB)

    Teminova, R.

    2007-06-29

    Passive remote Surface Acoustic Wave (SAW) sensors have been applied e.g. as temperature, pressure or torque sensors. Their important advantages over standard methods are their passive operating principle, which allows operation without any power supply, as well as the wireless high-frequency signal transmission over distances up to about 10..15 m even through (non metallic) housings. These properties of SAW sensors particularly qualify them for applications in high voltage operational equipment. First experience was gained in a long time field test of surge arrester monitoring based on SAW temperature sensors in a German high-voltage substation. Now, this system has been further developed at Darmstadt University of Technology for other applications, the first of them being an overhead line (OHL) conductor temperature measurement, the second one a temperature monitoring system for of high-voltage disconnectors. After designing and building the sensors, extensive laboratory tests were carried out applying high-voltage, high-current and thermal stress in order to approve the suitability for the intended application. All these tests confirmed the assumption that SAW sensors, due to their passive working principle, are not affected at all by any kind of electrical, magnetic or thermal stress that may occur during service. The complete temperature sensor consists of three parts: a sensor chip, an antenna which receives and transmits the signal from and to the radar unit and a body for installation and for protection against environmental impact. One must find a good compromise between optimizing of thermal, dielectric and high-frequency characteristics and at the same time taking into consideration a simple installation. These requirements on the SAW sensors turned out to be difficult to coordinate. To achieve a high measuring precision is especially difficult. First, a new sensor for OHL application was developed. The OHL conductor temperature sensor had been optimized

  14. Interface properties of magnetic tunnel junction La0.7Sr0.3MnO3/SrTiO3 superlattices studied by standing-wave excited photoemission spectroscopy

    NARCIS (Netherlands)

    Gray, A.X.; Papp, C.; Balke, B.; Yang, S.-H.; Huijben, M.; Rotenberg, E.; Bostwick, A.; Ueda, S.; Yamashita, Y.; Kobayashi, K.; Gullikson, E.M.; Kortright, J.B.; Groot, de F.M.F.; Rijnders, G.; Blank, D.H.A.; Ramesh, R.; Fadley, C.S.

    2010-01-01

    The chemical and electronic-structure profiles of magnetic tunnel junction (MTJ) La0.7Sr0.3MnO3/SrTiO3 (LSMO/STO) superlattices have been quantitatively determined via soft and hard x-ray standing-wave excited photoemission, x-ray absorption and x-ray reflectivity, in conjunction with x-ray optical

  15. Determination of dopant atomic positions with kinematical X-ray standing waves; Untersuchung von Fremdatomen in kristallinen Materialien mit kinematischen stehenden Roentgenwellen

    Energy Technology Data Exchange (ETDEWEB)

    Walz, Bente

    2011-11-15

    Recent advances in the kinematic X-ray standing wave technique (KXSW) for the determination of the atomic coordinates and displacement parameters in nonperfect crystalline materials are described in this thesis. The methodology has been improved by considering three significant aspects: - the inclusion of weak multiple beam contributions - the excitation of secondary fluorescence in multiple-element samples - the influence of the crystal mosaicity on the fluorescence yield. The improvements allowed to successfully apply the method to investigate complex oxide materials of current interest for potential device applications. The thermally-induced interdiffusion of cobalt and manganese thin films on zinc oxide single crystals has been studied to determine which lattice sites are occupied preferentially. The data analysis revealed that after thermal diffusion the adsorbed atoms occupied zinc sites in the host lattice. The mean deviation of the cobalt atomic position from the zinc lattice site was comparable to the thermal displacement parameter of the zinc atoms. In the case of manganese a secondary phase was found on the surface. Measurements performed on LaSrMnO{sub 4} provided new insight concerning the rotation of the oxygen octahedron around the manganese atoms and the concomitant displacements of the strontium and lanthanum atoms. It was found that the oxygen octahedra are rotated around the [100]-direction by 4,5 . The measurements in transmission geometry performed on titanium dioxide (rutile) demonstrated that KXSW measurements in the Laue geometry is a viable technique. By performing KXSW under grazing-incidence conditions it is possible to achieve depth resolution. The results clearly show that the extended KXSW technique is a versatile method for characterizing complex material systems. (orig.)

  16. Toward a real time stand-off submillimeter-wave imaging system with large field of view: quasi-optical system design considerations

    Science.gov (United States)

    Gandini, Erio; Llombart, Nuria

    2015-05-01

    In the frame-work of the European project CONSORTIS, a stand-off system for concealed object detections working at submillimeter-wave frequencies is being developed. The system is required to perform real-time image acquisition over a large field of view at a short range using both an active and a passive sensor operating in the frequency range from 250 to 600 GHz. In this contribution, the main trade-offs associated with the quasi-optical system design are presented. The imaging distance is from 2 m to 5 m range with a spatial resolution lower than 2 cm. Focal plane arrays will be used to achieve high imaging frame rates. Two configurations are considered in CONSORTIS: a sparse array of active transceivers and incoherent passive staring array with a large number of elements. Both cases use mechanical scanning to achieve the required field of view. This paper presents an in-depth analysis of the different trade-offs driving the quasi-optical design: from the mechanical scanner considerations to the optical beam quality required over the whole field of view. This analysis starts from the fundamental limitations of the quasi-optical mechanical systems. The limitations of the optics are discussed considering a canonical elliptical reflector as a reference. After this fundamental analysis, we compare the performances of several practical standard implementations, based on dual-reflectors and lenses, with canonical geometries. It is shown that, at short ranges, the main limitation of the optical system is the poor beam quality associated with the wide angular field of view and none of the standard implementation fulfills the requirements. In the last section, a technique to overcome this limitation is investigated. In particular, the use of optics with oversized reflectors can significantly improve the performance over a larger field of view if the coma aberrations are limited by a good angular filter.

  17. 驻波电帘除尘效率的实验研究%Experimental Study on Efficiency of Dust Removal by Standing Wave Electric Curtain

    Institute of Scientific and Technical Information of China (English)

    孙旗霞; 杨宁宁; 肖志坤; 蔡小兵; 胡更开

    2012-01-01

    月尘将对在月球表面进行巡视探测的设备产生严重不利影响。文章分析了利用驻波电帘对探测器的太阳电池板进行尘埃清除和防护,给出了电帘表面的电场分布,颗粒在电帘表面的受力状态和起跳、跃移过程,通过实验测量给出了电帘结构各参数对除尘效率的影响,制备了自清洁演示系统,对电帘的能耗进行了测定;表明驻波电帘是月表探测任务中尘埃防护的有效方法。%Lunar dust is expected to pose great harm to the instruments for lunar surface explora- tion. In this paper, dust removal from solar panel by using standing wave electric curtain is stud- ied. The electric field distribution on surface of the curtain is revealed, forces and levitation and transportation processes of the dust particles are investigated. Through experimental measure- ment, the influence of the structural parameters of electric curtain on the dust removal efficiency is characterised. A selbclean solar panel demonstration system is manufactured, and the energy consumption of the electric curtain measured. The results convey that electric curtain is an effec- tive technology for dust control in lunar surface exploration mission.

  18. X-ray standing-wave study of (AlAs){sub m}(GaAs){sub n} short-period superlattices

    Energy Technology Data Exchange (ETDEWEB)

    Lessmann, A.; Brennan, S.; Munkholm, A. [Stanford Synchrotron Radiation Laboratory SSRL/SLAC, 2575 Sand Hill Road, Menlo Park, California 94025 (United States); Schuster, M.; Riechert, H. [Siemens AG, Corporate Technology, Otto-Hahn-Ring 6, D-81739 Munich (Germany); Materlik, G. [Hamburger Synchrotronstrahlungslabor HASYLAB am Deutschen Elektronen-Synchrotron DESY, Notkestrasse 85, D-22603 Hamburg (Germany)

    1999-04-01

    X-ray standing-waves (XSW) are used for an investigation of the structure of (AlAs){sub m}(GaAs){sub n} short-period superlattices (SL{close_quote}s). The XSW induced modulation of x-ray fluorescence from the Al, As, and Ga atoms and the total photoelectron yield are monitored around the 0th order SL satellite (AlAs)(GaAs)(004,0) and the GaAs(004) substrate Bragg reflection. From the specific shape of these modulations and the sample reflectivity, an atomic model about the interfaces is derived. This is accomplished by comparing the experimental data with dynamical calculations of x-ray wavefield distribution and reflectivity, which are based on the Takagi-Taupin equation. The fluorescence measurements at the 0th order SL satellite reveal a high crystalline order in the AlAs layers of the short-period SL, whereas in the GaAs layers, a fraction of the Ga and As atoms is not on the ideal lattice positions. From the analysis, a model of the atomic distribution along the [001] direction can be determined. This reveals that at each internal interface in the GaAs layers, two Ga atom planes are shifted by up to 0.035 nm and one As atom plane by 0.023 nm. At each interface, the shifts are directed towards the substrate. In addition, the XSW field at the GaAs(004) substrate reflection results in a moir{acute e} or beating effect in the SL structure, which can be used to determine the information depth {Lambda}{sub e} of total electron-yield measurements in a more detailed approach. {copyright} {ital 1999} {ital The American Physical Society}

  19. Thermal effects on Co/Mo2C multilayer mirrors studied by soft x-ray standing wave enhanced photoemission spectroscopy

    Science.gov (United States)

    Giglia, A.; Mukherjee, S.; Mahne, N.; Nannarone, S.; Jonnard, P.; Le Guen, K.; Yuan, Y.-Y.; André, J.-M.; Wang, Z.-S.; Li, H.-C.; Zhu, J.-T.

    2013-05-01

    Here is presented the spectroscopic study of the evolution of the first buried interfaces of a B4C capped Co/Mo2C multilayer mirror induced by thermal treatment up to 600°C. This kind of study is typically performed to simulate the response of multilayer optics working in extreme conditions, as for instance when irradiated by new high brilliance sources as Free Electron Lasers. In fact, the efficiency of multilayers is related to the optical contrast between the alternating high and low density layers, and then to the degree of interdiffusion and the creation or evolution of interface compounds. The analysis has been performed at the Co L23 edge with different soft x-ray spectroscopic techniques including diffuse and specular reflectivity, total electron and fluorescent yield at the BEAR beamline at Elettra (Trieste) (http://www.elettra.trieste.it/elettra-beamlines/bear.html). The presentation is focused on the spectroscopic results obtained by soft x-ray standing wave enhanced photoemission (XSW) from the Mo 3d, B 1s, C 1s, O 1s core levels by using a photon energy close to the Co L23 edge and corresponding to the first Bragg peak of the multilayer. The experimental results have been compared with simulations to obtain information both on the chemical state (e.g. oxidation state) and interface morphology in terms of profiles of distribution of elements and interdiffusion of B, oxidized B and C in the interface region. In summary, it is possible to conclude in favour of a good stability of the multilayer in the investigated temperature range, as confirmed by the good performance in terms of reflectivity. These results confirm the usefulness of XSW for this kind analysis of multilayer optics.

  20. Co/Mo2C mirror as studied by x-ray fluorescence and photoelectron spectroscopies induced by x-ray standing waves

    Science.gov (United States)

    Jonnard, P.; Le Guen, K.; Yuan, Y. Y.; André, J.-M.; Mukherjee, S.; Giglia, A.; Nannarone, S.; Mahne, N.; Wang, Z.-S.; Li, H.-C.; Zhu, J.-T.

    2012-12-01

    We study a periodic Co/Mo2C multilayer prepared by magnetron sputtering. The period is 4.1 nm and the sample is designed to work around 778 eV, i.e. close to the Co 2p3/2 threshold, at a glancing angle of 11°. In this condition, strong x-ray standing waves set up within the sample. In order to probe different depths within the stack, particularly the interfaces, the glancing angle is moved along the first Bragg peak, while, the B 1s, C 1s, Mo 3d or O 1s photoelectron spectra, the Co Lα x-ray spectrum as well as the drain current of the sample are measured. Boron is present in the 3.5 nm B4C capping layer and oxygen is from surface contamination. The photoelectrons bring information from the superficial zone, i.e. the 5 first nm, while the characteristic x-rays probe the whole stack. Clear modulations of the intensity of the studied signals as well as core level shifts are observed when going through the Bragg peak. In order to understand what happens in the multilayer calculations of depth distributions of the electric field and the energy loss by the radiation are made with the IMD and OPAL codes, respectively. The combination of experimental results and theoretical simulations will enable us to determine from which place originate the various signals and to know if some interaction exists between the Co and Mo2C layers.

  1. Au enrichment and vertical relaxation of the Cu3Au (111 ) surface studied by normal-incidence x-ray standing waves

    Science.gov (United States)

    Bauer, O.; Schmitz, C. H.; Ikonomov, J.; Willenbockel, M.; Soubatch, S.; Tautz, F. S.; Sokolowski, M.

    2016-06-01

    We have investigated the Cu3Au (111 ) surface, prepared under ultrahigh vacuum conditions by sputtering and annealing, by low energy electron diffraction (LEED), scanning tunneling microscopy (STM), x-ray photoelectron spectroscopy, and normal incidence x-ray standing waves (NIXSW). We find the surface to be depleted with Cu and enriched with Au at the same time, yielding a nominal Cu:Au ratio of 0.61:0.39 in the topmost layer. The STM images reveal that the first layer is nearly closely filled with atoms and contains a small amount of vacancies with an area concentration of about 5 % . Together with the Au enrichment, these cause local short-range disorder of the Au p (2 ×2 ) reconstruction. From this data, the average stoichiometry of the p (2 ×2 ) surface unit cell is estimated at C u2.22A u1.44□0.20 (instead of C u3.00A u1.00□0.00 of the ideal surface; □ denotes an atomic vacancy site). From NIXSW we find a significant outward relaxation of both the Cu and Au atoms of the topmost layer by 0.28 Å and 0.33 Å, which corresponds to 13 % and 15 % of the (111) bulk layer spacing of C u3Au . We suggest that this originates from a widening of the first/second layer spacing, by 6.8 % and 8.8 % for the Cu and Au atoms, respectively, plus an additional rigid increase in the second/third layer spacing by 6.2 % . We explain this by steric repulsions between Au atoms of the topmost layer, replacing smaller Cu atoms, and Au atoms in the second layer in combination with disorder. Finally, a lateral reconstruction, similar to that on the Au(111) surface, but with a much larger periodicity of 290 Å, is identified from LEED.

  2. 阻尼振荡波电压和工频电压下XLPE电缆局部放电特性的对比研究%Comparative Study on Partial Discharge Characteristics of XLPE Cable under Damped Oscillating Wave Voltage and AC Voltage

    Institute of Scientific and Technical Information of China (English)

    薛荣; 张龙; 黄志伟; 张伟; 李洪杰

    2015-01-01

    The partial discharge characteristics of four defects in heat-shrinkable cable accessories, which were termination without stress tube, incorrect use of insulation tape as semi-conductive adhesive tape in the middle joint, void and metal particles on the surface of XLPE insulation, were studied by AC volt-age method and damped oscillating wave voltage method. The partial discharge inception voltage and pat-terns under damped oscillating wave voltage and AC voltage were compared. The results show that the two methods are consistent in the study of partial discharge characteristics, and there are obvious differ-ences in the partial discharge statistical characteristics of various defects.%采用工频电压法和阻尼振荡波电压法研究热缩式电缆附件在4种缺陷情况下的局部放电特性,对比分析两种电压情况下的局部放电起始电压和局放模式。结果表明:两种方法在局部放电特性研究中具有一致性,各种缺陷的局部放电统计特征具有较为明显的差异。

  3. 直线加速器驻波腔中的瞬态束流负载效应%Transient Beam Loading Effects in Standing Wave Cavities of Linear Accelerators

    Institute of Scientific and Technical Information of China (English)

    裴士伦; 王书鸿

    2006-01-01

    在高能加速器中,随着单个束团和束团串中电荷量的提高,当粒子束穿过加速腔的时候,感应出的瞬态束流负载电压也越来越高.但是,在通常分析束流负载的时候,往往对稳态束流负载研究的比较多,而对瞬态束流负载的研究要相对少一些.本文首先对束流负载的瞬态特性和束团穿过加速腔时高频源所看到谐振腔谐振频率的变化方式进行了分析,然后又对两种情况下谐振腔的最优失谐条件进行了讨论,并给出了相应的解析公式.在第1种情况下,当粒子束穿过加速腔的时候,谐振腔的自然谐振频率能够及时地得到调节,从而使高频源的电流与谐振腔的腔压同相,以提高高频源的效率;在第2种情况下,当粒子束穿过加速腔的时候,谐振腔的自然谐振频率保持不变,不能被调节.最后,还对BEPCⅡ现有预注入器的预聚束腔、BEPCⅡ未来预注入器的两个次谐波聚束腔中的瞬态束流负载效应进行了分析.%In modern high energy accelerators, with the increase of charge in a bunch or a bunch train,the induced transient beam loading voltages become higher and higher when the beams pass through the standing wave cavities. But in the usual analysis, people usually pay more attention to the steady state instead of the transient state beam loading. In this paper, the transient nature of beam loading and the cavity's frequency changing behavior seen by the RF power generator are studied, and then the optimum detuning conditions in two cases are derived. In the first case, the resonant cavity's frequency can be tuned to meet the in-phase condition between the RF power generator current and the cavity voltage during the passage of beams. While in the second case, only few bunches in the bunch train and the cavity's resonant frequency is fixed during the passage of the bunch train. At last, the beam loading effects in the prebuncher of BEPC Ⅱ pre-injector and the two SHBs of

  4. A finite volume algorithm for solving nonlinear standing waves in acoustic resonators%谐振管内非线性驻波的有限体积数值算法

    Institute of Scientific and Technical Information of China (English)

    宁方立; 董梁; 张文治; 王康

    2012-01-01

    In order to expand the engineering application area of nonlinear standing waves in acoustic resonators, a new numerical algorithm is proposed for simulating nonlinear standing waves in resonators. It also can be used to overcome the shortages of the existing numerical methods, which restrict the solution to the nonlinear standing waves in cylindrical resonators and exponential resonators. The numerical algorithm is constructed based on the Navier-Stokes equations in the resonators with variable cross-section for an unsteady compressible thermoviscous fluid without truncation, and the space conservation law. The numerical algorithm-finite volume method for solving the nonlinear standing waves in acoustic resonators by piston driving is built based on the semi-implicit method for pressure-linked equations-consistent algorithm and staggered grid technique. Simulations for solving the nonlinear standing waves in cylindrical resonators, exponential resonators and conical resonators are carried out. By comparison with the existing experimental results and numerical simulation results, the accuracy of the developed finite volume algorithm is verified. Some new physical results are obtained, including unsteady velocity, density and temperature. The shock-like pressure wave shapes are found in cylindrical resonators, simultaneously, and the results show that the sharp velocity spikes appear in the cylindrical resonators. High amplitude acoustic pressures are generated in exponential resonators and conical resonators. Shock-like pressure waves and the sharp velocity spikes are not found. The strong dependence of the physical properties of nonlinear standing waves on resonator shape is demonstrated through the simulative results.%为了扩展谐振管内非线性驻波在工程中的应用,以及克服现有数值计算方法仅局限于求解直圆柱形和指数形谐振管内非线性驻波的问题.根据变截面的非稳态可压缩热黏性流体Navier-Stokes方

  5. Low-voltage gyrotrons

    Science.gov (United States)

    Glyavin, M. Yu.; Zavolskiy, N. A.; Sedov, A. S.; Nusinovich, G. S.

    2013-03-01

    For a long time, the gyrotrons were primarily developed for electron cyclotron heating and current drive of plasmas in controlled fusion reactors where a multi-megawatt, quasi-continuous millimeter-wave power is required. In addition to this important application, there are other applications (and their number increases with time) which do not require a very high power level, but such issues as the ability to operate at low voltages and have compact devices are very important. For example, gyrotrons are of interest for a dynamic nuclear polarization, which improves the sensitivity of the nuclear magnetic resonance spectroscopy. In this paper, some issues important for operation of gyrotrons driven by low-voltage electron beams are analyzed. An emphasis is made on the efficiency of low-voltage gyrotron operation at the fundamental and higher cyclotron harmonics. These efficiencies calculated with the account for ohmic losses were, first, determined in the framework of the generalized gyrotron theory based on the cold-cavity approximation. Then, more accurate, self-consistent calculations for the fundamental and second harmonic low-voltage sub-THz gyrotron designs were carried out. Results of these calculations are presented and discussed. It is shown that operation of the fundamental and second harmonic gyrotrons with noticeable efficiencies is possible even at voltages as low as 5-10 kV. Even the third harmonic gyrotrons can operate at voltages about 15 kV, albeit with rather low efficiency (1%-2% in the submillimeter wavelength region).

  6. Applications of passive remote surface acoustic wave sensors in high-voltage systems; Einsatz von passiven funkabfragbaren Oberflaechenwellensensoren in der elektrischen Energietechnik

    Energy Technology Data Exchange (ETDEWEB)

    Teminova, R.

    2007-06-29

    Passive remote Surface Acoustic Wave (SAW) sensors have been applied e.g. as temperature, pressure or torque sensors. Their important advantages over standard methods are their passive operating principle, which allows operation without any power supply, as well as the wireless high-frequency signal transmission over distances up to about 10..15 m even through (non metallic) housings. These properties of SAW sensors particularly qualify them for applications in high voltage operational equipment. First experience was gained in a long time field test of surge arrester monitoring based on SAW temperature sensors in a German high-voltage substation. Now, this system has been further developed at Darmstadt University of Technology for other applications, the first of them being an overhead line (OHL) conductor temperature measurement, the second one a temperature monitoring system for of high-voltage disconnectors. After designing and building the sensors, extensive laboratory tests were carried out applying high-voltage, high-current and thermal stress in order to approve the suitability for the intended application. All these tests confirmed the assumption that SAW sensors, due to their passive working principle, are not affected at all by any kind of electrical, magnetic or thermal stress that may occur during service. The complete temperature sensor consists of three parts: a sensor chip, an antenna which receives and transmits the signal from and to the radar unit and a body for installation and for protection against environmental impact. One must find a good compromise between optimizing of thermal, dielectric and high-frequency characteristics and at the same time taking into consideration a simple installation. These requirements on the SAW sensors turned out to be difficult to coordinate. To achieve a high measuring precision is especially difficult. First, a new sensor for OHL application was developed. The OHL conductor temperature sensor had been optimized

  7. Motion-induced X-ray and terahertz radiation of electrons captured in laser standing wave%电子在激光驻波场中运动产生的太赫兹及X射线辐射研究∗

    Institute of Scientific and Technical Information of China (English)

    朱卫卫; 张秋菊; 张延惠; 焦扬

    2015-01-01

    The motions of charged particles in electromagnetic fields composed of two or more laser beams show a variety of forms due to the adjustable properties of electromagnetic fields. In this paper, we consider the periodic laser standing wave field composed of two laser beams with opposite propagating directions. The movement of electrons in the standing wave field shows a periodic behavior, accompanied with the obvious radiation, especially when electrons are captured by the laser standing wave field. This phenomenon has aroused much interest of us. Under the existing experimental conditions, the free electron beam with low energy from an electron gun or the relativistic electron beam generated from laser acceleration can be easily obtained and injected into the periodic standing wave field. In this paper, using the single-electron model and the classical radiation theory of charged particles, we study the motion and radiation processes of low and high energy electrons in the polarized laser standing wave field. The results show that when the direction of incident electrons with low-speed is perpendicular to the direction of the laser standing wave electric field, the one-dimensional nearly periodic motion of electrons evolves into a two-dimensional folded movement by gradually increasing the light intensity of the laser standing wave field, and the strong terahertz radiation at micrometer wavelength is produced. High energy electrons generate the high-frequency radiation with the wavelength at several nanometers when the incident direction of high energy electrons is perpendicular or parallel to the direction of the laser standing wave electric field. In the case of low-energy electron, the motion of electron, frequency and intensity of radiation are affected by the laser intensity. In the case of incident high-energy electrons, the laser intensity affects the intensity of electronic radiation, and the initial electron energy influences radiation frequency. The

  8. VOLTAGE REGULATORS ASYNCHRONOUS GENERATORS

    Directory of Open Access Journals (Sweden)

    Grigorash O. V.

    2015-06-01

    Full Text Available A promising is currently the use of asynchronous generators with capacitive excitation as a source of electricity in stand-alone power systems. Drive asynchronous generators may exercise as a thermal engine and wind wheel wind power plant or turbines of small hydropower plants. The article discusses the structural and schematics of voltage stabilizers and frequency of asynchronous generators with improved operational and technical specifications. Technical novelty of design solutions of the magnetic system and stabilizers asynchronous generator of electricity parameters confirmed by the patents for the invention of the Russian Federation. The proposed technical solution voltage stabilizer asynchronous generators, can reduce the weight of the block capacitors excitation and reactive power compensation, as well as to simplify the control system power circuit which has less power electronic devices. For wind power plants it is an important issue not only to stabilize the voltage of the generator, but also the frequency of the current. Recommend functionality stabilizer schemes parameters of electric power made for direct frequency converters with artificial and natural switching power electronic devices. It is also proposed as part of stabilization systems use single-phase voltage, three-phase transformers with rotating magnetic field, reduce the level of electromagnetic interference generated by power electronic devices for switching, enhance the efficiency and reliability of the stabilizer.

  9. Design and Characterization of a W-Band Folded-Waveguide Slow-Wave Structure

    Science.gov (United States)

    Sumathy, Murugan; Datta, Subrata Kumar

    2016-12-01

    A single-section slow-wave structure for a W-band folded-waveguide traveling-wave tube with operating bandwidth of around 4% was designed for delivering the output power of 50 W at the operating voltage of 13.5 kV and operating beam current of 80 mA. The design was carried out using analytical formulations and 3D electromagnetic simulations. The beam-wave interaction analysis was carried out using large signal Lagrangian analysis and particle-in-cell simulation. The folded-waveguide slow-wave structure along with input-output couplers and RF windows were fabricated. Cold test measurements were carried out for dispersion characteristics of the slow-wave structure and voltage standing-wave ratio and insertion loss characteristics of the RF window. The measured cold circuit parameters show close agreement with the analysis.

  10. In Situ Structural Studies of the Underpotential Deposition of Copper onto an Iodine Covered Platinum Surface Using X-Ray Standing Waves

    Science.gov (United States)

    1991-01-01

    ABSTRAc C We present initial results of an in situ structural investigation of the underpotential deposition of copper on an iodine covered platinum...compare the result of surface coverage isotherms derived from both electrochemical and x-ray measurements. 1. INTRODUCIION The underpotential deposition ...the underpotential deposition of copper on an iodine covered platinum/carbon layered synthetic microstructure. 2 THEORETICAL BACKGROUND X-ray standing

  11. High Voltage Seismic Generator

    Science.gov (United States)

    Bogacz, Adrian; Pala, Damian; Knafel, Marcin

    2015-04-01

    This contribution describes the preliminary result of annual cooperation of three student research groups from AGH UST in Krakow, Poland. The aim of this cooperation was to develop and construct a high voltage seismic wave generator. Constructed device uses a high-energy electrical discharge to generate seismic wave in ground. This type of device can be applied in several different methods of seismic measurement, but because of its limited power it is mainly dedicated for engineering geophysics. The source operates on a basic physical principles. The energy is stored in capacitor bank, which is charged by two stage low to high voltage converter. Stored energy is then released in very short time through high voltage thyristor in spark gap. The whole appliance is powered from li-ion battery and controlled by ATmega microcontroller. It is possible to construct larger and more powerful device. In this contribution the structure of device with technical specifications is resented. As a part of the investigation the prototype was built and series of experiments conducted. System parameter was measured, on this basis specification of elements for the final device were chosen. First stage of the project was successful. It was possible to efficiently generate seismic waves with constructed device. Then the field test was conducted. Spark gap wasplaced in shallowborehole(0.5 m) filled with salt water. Geophones were placed on the ground in straight line. The comparison of signal registered with hammer source and sparker source was made. The results of the test measurements are presented and discussed. Analysis of the collected data shows that characteristic of generated seismic signal is very promising, thus confirms possibility of practical application of the new high voltage generator. The biggest advantage of presented device after signal characteristics is its size which is 0.5 x 0.25 x 0.2 m and weight approximately 7 kg. This features with small li-ion battery makes

  12. Wave

    DEFF Research Database (Denmark)

    Ibsen, Lars Bo

    2008-01-01

    Estimates for the amount of potential wave energy in the world range from 1-10 TW. The World Energy Council estimates that a potential 2TW of energy is available from the world’s oceans, which is the equivalent of twice the world’s electricity production. Whilst the recoverable resource is many t...

  13. Scalable single point power extraction for compact mobile and stand-alone solar harvesting power sources based on fully printed organic photovoltaic modules and efficient high voltage DC/DC conversion

    DEFF Research Database (Denmark)

    Garcia Valverde, Rafael; Villarejo, José A.; Hösel, Markus

    2015-01-01

    Patterns for fully printed polymer solar cells are presented that inherently enable scaling of the power output with single point electrical energy connection is presented. Connection is made to only one end of the printed foil that can be rolled out for light energy harvesting. The power level...... is simply increased/decreased by increasing/decreasing the length of the foil with a corresponding increase/decrease in operating voltage. The current flow runs in both directions along the printed foil thus alleviating the need for post process addition of complex busbar topologies. The power conversion...... takes place in a HVDC–DC converter that is tailored specifically for operation with polymer solar cells by regulation on the input side. The system charges a lithium-polymer battery thus enabling storage of 82 Wh for a printed OPV foil measuring 0.305 m×9 m having a nominal power output of at least 15 W...

  14. No-Voltage Meter

    Science.gov (United States)

    1976-02-01

    VW- IKft, 1/4 H4 -Wv- IK!1, I/4W INTERNAL VOLTAGE NOTE ALL TRANSISTORS ARE 2N43A OR EQUIVALENT GERMANIUM ALLOY PNP AA ALKALINE BATTERY...D-,, regardless of polarity. This signal is then full-wave rectified by the diode-connected Germanium transistor bridge, T,, T-,, T3, and T4... Transistor T5 acts as a second current limiter. Resistor R2 was selected to give 90 f# of full-scale meter deflection with an input signal of 115 volts

  15. Portable High Voltage Impulse Generator

    Directory of Open Access Journals (Sweden)

    S. Gómez

    2011-07-01

    Full Text Available This paper presents a portable high voltage impulse generator which was designed and built with insulation up to 20 kV. This design was based on previous work in which simulation software for standard waves was developed. Commercial components and low-cost components were used in this work; however, these particular elements are not generally used for high voltage applications. The impulse generators used in industry and laboratories are usually expensive; they are built to withstand extra high voltage and they are big, making them impossible to transport. The proposed generator is portable, thereby allowing tests to be made on devices that cannot be moved from their location. The results obtained with the proposed impulse generator were satisfactory in terms of time and waveforms compared to other commercial impulse generators and the standard impulse wave simulator.

  16. Experimental validation of a high voltage pulse measurement method.

    Energy Technology Data Exchange (ETDEWEB)

    Cular, Stefan; Patel, Nishant Bhupendra; Branch, Darren W.

    2013-09-01

    This report describes X-cut lithium niobates (LiNbO3) utilization for voltage sensing by monitoring the acoustic wave propagation changes through LiNbO3 resulting from applied voltage. Direct current (DC), alternating current (AC) and pulsed voltage signals were applied to the crystal. Voltage induced shift in acoustic wave propagation time scaled quadratically for DC and AC voltages and linearly for pulsed voltages. The measured values ranged from 10 - 273 ps and 189 ps 2 ns for DC and non-DC voltages, respectively. Data suggests LiNbO3 has a frequency sensitive response to voltage. If voltage source error is eliminated through physical modeling from the uncertainty budget, the sensors U95 estimated combined uncertainty could decrease to ~0.025% for DC, AC, and pulsed voltage measurements.

  17. The dynamic response of a hot-wire anemometer: IV. Sine-wave voltage perturbation testing for near-wall hot-wire/film probes and the presence of low-high frequency response characteristics

    Science.gov (United States)

    Teo, C. J.; Khoo, B. C.; Teo, C. J.; Chew, Y. T.

    2001-01-01

    Experiments were performed using the electronic sine-wave voltage-perturbation test to systematically study the frequency responses of near-wall hot-wire probes subjected in turn to varying magnitudes of convective velocity and different effects of wall influence. In addition, quartz-substrate hot-film gauges with various thicknesses of quartz coating were also investigated. Results of the high cut-off frequency obtained using the sine-wave test (fsine) were found to be in fair agreement with those obtained using the square-wave test (fS) both for hot-wire and for hot-film sensors. The sine-wave test response curve exhibited a distinct bulging effect for the hot-film gauges. For the hot-wire sensors, a much weaker bulging effect was also observed. In contrast to fS and fsine, the low frequency response characteristic corresponding to the location of the bulging effect (fbulge) compared much more favourably with the dynamic frequency response (fD) obtained by Khoo et al and Chew et al using a known near-wall fluctuating flow field. Freymuth's theory for non-cylindrical hot-film sensors incorporating the Bellhouse-Schultz model was applied to predict the responses of the hot-film wall gauges when they were subjected to electronic sine-wave testing and dynamic perturbation testing under different parametric conditions. Although it is one-dimensional in nature, the model is capable of predicting most of the trends observed in the present study and previous works by Khoo et al (1998a) and Chew et al (1998a).

  18. Standing steady-state wave-making calculation method for air cushion vehicles; Air cushion vehicle no teijo zoha keisanho ni tsuite

    Energy Technology Data Exchange (ETDEWEB)

    Eguchi, T. [Mitsui Engineering and Shipbuilding Co. Ltd., Tokyo (Japan)

    1996-04-10

    The pulse-height distribution of a cushion room of air cushion vehicle (ACV) has been tried to be approached by means of the panel shift type Rankine source method. When using this method, it was not required to introduce the pressure distribution model simulating the fall-off effect for the step-formed cushion pressure distribution. The wave form and wave making resistance could be estimated precisely by assigning the pressure gradient to one longitudinal direction panel in the calculation. The waveform shape within the cushion room could be calculated rather precisely by comparing with the analytic solution. This calculation method did have an ability providing the pulse-height information in the cushion room of ACV for seal design and configuration of ships. The analytic solution using for the comparison was sufficient for determining the pulse-height in the high speed region. However, it was hard to respond to non-linear problems or optional shape problems. It was pointed out to be further improved. 5 refs., 8 figs.

  19. Programable Driver for Voltage-Controlled Oscillators

    Science.gov (United States)

    Fowler, L. E.; Mcneil, J. A.

    1985-01-01

    Electronically programable read-only memory (EPROM) and digital-to-analog converter provide customized time-varying voltage for frequency modulation. Voltage used to modulate IMPATT oscillator that serves as microwave pump for solid-state maser in low-noise amplifier. EPROM simple to tailor voltage waveform to suit characteristics of given maser. Digital information for waveform programed into EPROM chip; digital-to-analog converter reads information and produces corresponding analog wave. Principle readily adapted to other applications.

  20. Accurate Switched-Voltage voltage averaging circuit

    OpenAIRE

    金光, 一幸; 松本, 寛樹

    2006-01-01

    Abstract ###This paper proposes an accurate Switched-Voltage (SV) voltage averaging circuit. It is presented ###to compensated for NMOS missmatch error at MOS differential type voltage averaging circuit. ###The proposed circuit consists of a voltage averaging and a SV sample/hold (S/H) circuit. It can ###operate using nonoverlapping three phase clocks. Performance of this circuit is verified by PSpice ###simulations.

  1. Research and Development and Related Experimental Study of Standing Wave Tude System for Sound Absorbing Wedge%吸声尖劈测试用驻波管系统研制及试验研究

    Institute of Scientific and Technical Information of China (English)

    姚磊; 童宪; 裘剑敏; 罗丰; 王欢

    2012-01-01

    主要介绍吸声尖劈测试用驻波管系统的研制及相关试验的研究工作.本系统的构建与测试基于驻波比原理,管体矩形截面为0.6 m×0.6m,长度为7.2m.系统通过传声器传动系统实现管内声压随距离变化的自动测量,距离分辨率可达0.3 mm(5 mm/s移动速度下),在40 Hz~280 Hz频段内可对材料的吸声系数、声阻抗、反射系数、声导纳进行测试,克服传统驻波比测量方法测试精度不高、测量效率低的缺点,为高效、准确测量材料吸声性能提供很好的途径.目前还未见国内关于类似系统的报道,依据相关国家校准规范经第三方计量部门鉴定,各项技术指标均满足要求.同时还通过试验研究得出对实际吸声尖劈测试具有借鉴意义的结论.%Research and development and related experimental study of a standing wave tube system applied in sound absorbing wedge measurement were discussed in this article. Based on standing wave ratio principle, the tube system with 0.6 m×0.6 m rectangular cross-section and 7.2 m length was constituted. Sound pressure along the axial distance in the tube was measured through the microphone driven by an automatic driving system which has a distance resolution of 0.3 mm at 5 mm/s velocity. The acoustical parameters, such as sound absorbing coefficient, acoustic impedance, reflection factor and acoustic admittance can be obtained through the system within frequency band 40-280 Hz. The system overcame the shortcomings of traditional standing-wave measurement methods, which are the low measurement efficiency and low measurement precision. A new efficient and precise method was then provided for sound absorbing test. No similar system has been found in our country so far. The system was calibrated by a superior metrology institute and the technical data can meet the demands. Furthermore, the experiment related to the system was done and some referential conclusions for sound absorption

  2. Standing Tall: The Benefits of Standing Devices

    Science.gov (United States)

    Warner, Mark P.

    2007-01-01

    In the author's opinion as a pediatric physical therapist, with the exception of a wheelchair, there is no other piece of assistive technology that is more beneficial to children and adults with special needs than a standing device. Postural symmetry during standing and walking activities is extremely important for everyone. Very few children…

  3. Development of a voltage scanner of chopper

    CERN Document Server

    Shen Guan Ren; LiShengLi; WangQuanXing; Wu Long Cheng

    2001-01-01

    Development of voltage sweeper of chopper with CPNG are introduced. Voltage sweeper is one of important key parts of chopper. Two years working prove that it is stable and reliable. Its main technology performance save: sine wave frequency: 750 kHz +- 20 Hz; total distortion: 65 Db; output voltage (V-V): 0->=4000 V; the error7 W; voltage supply: 220V AC +-10%, 50 +- 1 Hz; total power supply: <100W; Work temperature range: 0 - 40 degree; Stability in long time <=1%

  4. Out-standing!

    DEFF Research Database (Denmark)

    Kural, René

    2013-01-01

    Out-standing concerns the Danish tennisplayer Leif Rovsing and his outstanding piece of architecture Danish Tennis Club in Hellerup.......Out-standing concerns the Danish tennisplayer Leif Rovsing and his outstanding piece of architecture Danish Tennis Club in Hellerup....

  5. Evolved Models for Elementary Particles and Atoms Require Alternating Neutrino/Antineutrino Pairs Along Interlocked or Looped Strings. Traveling Waves, TW, and Standing Waves, SW, Alternate at Nodal Notches

    Science.gov (United States)

    McLeod, Roger David; McLeod, David Matthew

    2009-05-01

    Our hydrogen atom interacts with a neutron star. Its stringy TW/SW electron is cut by a neutrino scissor that instantly becomes its end anti-node. The string has one extra neutrino in 100,000. Antimatter remains concealed. Our Dumbo Proton of a TW state is similarly cut. Inside the star, electron string/spring compresses 100,000 and 1836 times more, to proton's linear mass density. Electrostatics encourages that caboose, stringy electron, to couple with a cut proton. Linear charge densities neutralize while composite length contracts 20%. The writhing string evicts an antineutrino at closure on Pauli's authority, becoming Mickey Neutron, with looped quarks. Unstable Mickey Neutron has his ear notch forced into an ear notch of stable Dumbo Proton, achieving immortality in this deuteron marriage. Tritium is in a m'enage a trois. Alpha Nucleus has a # grid. Meta state Ne-20 predicts alpha eviction to O-16. Schr"odinger finally prevails, so string theory and Wave Mechanics can prosper.

  6. Structure of Hydrated Zn2+ at the Rutile TiO2 (110)-Aqueous Solution Interface: Comparison of X-ray Standing Wave, X-ray Absorption Spectroscopy, and Density Functional Theory Results

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, Zhan [Argonne National Laboratory (ANL); Fenter, Paul [Argonne National Laboratory (ANL); Kelly, Shelly D [Argonne National Laboratory (ANL); Catalano, Jeffery G. [Argonne National Laboratory (ANL); Bandura, Andrei V. [St. Petersburg State University, St. Petersburg, Russia; Kubicki, James D. [Pennsylvania State University; Sofo, Jorge O. [Pennsylvania State University; Wesolowski, David J [ORNL; Machesky, Michael L. [Illinois State Water Survey, Champaign, IL; Sturchio, N. C. [University of Illinois, Chicago; Bedzyk, Michael J. [Northwestern University, Evanston

    2006-01-01

    Adsorption of Zn{sup 2+} at the rutile TiO{sub 2} (110)-aqueous interface was studied with Bragg-reflection X-ray standing waves (XSW), polarization-dependent surface extended X-ray absorption fine structure (EXAFS) spectroscopy, and density functional theory (DFT) calculations to understand the interrelated issues of adsorption site, its occupancy, ion-oxygen coordination and hydrolysis. At pH 8, Zn{sup 2+} was found to adsorb as an inner-sphere complex at two different sites, i.e., monodentate above the bridging O site and bidentate between two neighboring terminal O sites. EXAFS results directly revealed a four or fivefold first shell coordination environment for adsorbed Zn{sup 2+} instead of the sixfold coordination found for aqueous species at this pH. DFT calculations confirmed the energetic stability of a lower coordination environment for the adsorbed species and revealed that the change to this coordination environment is correlated with the hydrolysis of adsorbed Zn{sup 2+}. In addition, the derived adsorption locations and the occupancy factors of both sites from three methods agree well, with some quantitative discrepancies in the minor site location among the XSW, EXAFS, and DFT methods. Additional XSW measurements showed that the adsorption sites of Zn{sup 2+} were unchanged at pH 6. However, the Zn{sup 2+} partitioning between the two sites changed substantially, with an almost equal distribution between the two types of sites at pH 6 compared to predominantly monodentate occupation at pH 8.

  7. Structure of Hydrated Zn2+ at the Rutile TiO2 (110)-Aqueous Solution Interface: Comparsion of X-ray Standing Wave, X-ray Absorption Spectroscopy, and Density Functional Theory Results

    Energy Technology Data Exchange (ETDEWEB)

    Zhang,Z.; Fenter, P.; Kelly, S.; Catalano, J.; Bandura, A.; Kubicki, J.; Sofo, J.; Wesolowski, D.; Machesky, M.; et al.

    2006-01-01

    Adsorption of Zn{sup 2+} at the rutile TiO2 (110)-aqueous interface was studied with Bragg-reflection X-ray standing waves (XSW), polarization-dependent surface extended X-ray absorption fine structure (EXAFS) spectroscopy, and density functional theory (DFT) calculations to understand the interrelated issues of adsorption site, its occupancy, ion-oxygen coordination and hydrolysis. At pH 8, Zn{sup 2+} was found to adsorb as an inner-sphere complex at two different sites, i.e., monodentate above the bridging O site and bidentate between two neighboring terminal O sites. EXAFS results directly revealed a four or fivefold first shell coordination environment for adsorbed Zn{sup 2+} instead of the sixfold coordination found for aqueous species at this pH. DFT calculations confirmed the energetic stability of a lower coordination environment for the adsorbed species and revealed that the change to this coordination environment is correlated with the hydrolysis of adsorbed Zn{sup 2+}. In addition, the derived adsorption locations and the occupancy factors of both sites from three methods agree well, with some quantitative discrepancies in the minor site location among the XSW, EXAFS, and DFT methods. Additional XSW measurements showed that the adsorption sites of Zn{sup 2+} were unchanged at pH 6. However, the Zn{sup 2+} partitioning between the two sites changed substantially, with an almost equal distribution between the two types of sites at pH 6 compared to predominantly monodentate occupation at pH 8.

  8. Localized standing waves in inhomogeneous Schrodinger equations

    CERN Document Server

    Marangell, R; Susanto, H

    2010-01-01

    A nonlinear Schrodinger equation arising from light propagation down an inhomogeneous medium is considered. The inhomogeneity is reflected through a non-uniform coefficient of the non-linear term in the equation. In particular, a combination of self-focusing and self-defocusing nonlinearity, with the self-defocusing region localized in a finite interval, is investigated. Using numerical computations, the extension of linear eigenmodes of the corresponding linearized system into nonlinear states is established, particularly nonlinear continuations of the fundamental state and the first excited state. The (in)stability of the states is also numerically calculated, from which it is obtained that symmetric nonlinear solutions become unstable beyond a critical threshold norm. Instability of the symmetric states is then investigated analytically through the application of a topological argument. Determination of instability of positive symmetric states is reduced to simple geometric properties of the composite phas...

  9. Travelling standing waves: a feasibility study

    NARCIS (Netherlands)

    Neer, P.L.M.J. van; Rasmijn, L.N.R.; Franse, W.J.M.; Geers, L.; Rasidovic, A.; Volker, A.W.F.

    2015-01-01

    Lately, there has been significant interest in the noninvasive manipulation of particles and liquids. The reported acoustic methods rely on either the acoustic radiation force or acoustic streaming. The latter can be used in developed flows to induce fluid velocities angled to the liquid flow direct

  10. Longitudinal stability in multiharmonic standing wave linacs

    Science.gov (United States)

    Carver, L. R.; Jones, R. M.; Jiang, Y.; Hirshfield, J. L.

    2016-09-01

    Accelerating cavities that excite multiple modes at integer harmonics of the fundamental frequency have the potential to be used to suppress the onset of rf breakdown and reduce the pulsed surface heating at high accelerating gradients. Understanding the effect of an additional harmonic cavity mode on the longitudinal beam dynamics is important to their development and use. A Hamiltonian that describes the longitudinal motion of a particle as it traverses a chain of multiharmonic cavities has been derived and is applied to the case of a second harmonic cavity. The Hamiltonian is based upon formalisms found in literature for the fundamental harmonic and is extended to include different longitudinal field distributions and harmonic frequencies. The study initially explores the longitudinal motion for moderate accelerating gradients with high-β protons, as this will allow fundamental properties of the stable region (acceptance and shape of the rf bucket) to be determined. High accelerating gradients are also investigated but the focus will be on phase stability throughout. This work concludes by considering the longitudinal dynamics of a modified European Spallation Source accelerator, comprised of multiharmonic cavities that has specifications broadly consistent with the accelerator.

  11. Effect of state feedback coupling on the transient performance of voltage source inverters with LC filter

    DEFF Research Database (Denmark)

    Federico, de Bosio; Pastorelli, Michele; Antonio DeSouza Ribeiro, Luiz

    2016-01-01

    State feedback coupling between the capacitor voltage and inductor current deteriorates notably the performance during transients of voltage and current regulators in stand-alone systems based on voltage source inverters. A decoupling technique is proposed, considering the limitations introduced ...... by system delays. Laboratory experiments were executed in compliance with the normative for Uninterruptible Power Supply systems to prove the developed analysis....

  12. Transient Voltage Recorder

    Science.gov (United States)

    Medelius, Pedro J. (Inventor); Simpson, Howard J. (Inventor)

    2002-01-01

    A voltage transient recorder can detect lightning induced transient voltages. The recorder detects a lightning induced transient voltage and adjusts input amplifiers to accurately record transient voltage magnitudes. The recorder stores voltage data from numerous monitored channels, or devices. The data is time stamped and can be output in real time, or stored for later retrieval. The transient recorder, in one embodiment, includes an analog-to-digital converter and a voltage threshold detector. When an input voltage exceeds a pre-determined voltage threshold, the recorder stores the incoming voltage magnitude and time of arrival. The recorder also determines if its input amplifier circuits clip the incoming signal or if the incoming signal is too low. If the input data is clipped or too low, the recorder adjusts the gain of the amplifier circuits to accurately acquire subsequent components of the lightning induced transients.

  13. Relationships between Harmonic Characteristics and Different Types of Voltage Source

    Directory of Open Access Journals (Sweden)

    Yusniati Yusniati

    2012-06-01

    Full Text Available This paper discusses about harmonic characteristics due to different types of voltage sources. Usually, the voltage source is sinusoidal. But in actual condition the load that receive voltage sources through the elements where the output voltage of element as input to the load is not pure sinusoidal, for example voltage source at  (PCC between transformer and linear load and nonlinear load. This research has been done with Schhafner Power Quality Analyzer and PM300 Power Quality Analyzer, was focused to all harmonic characteristics as power, voltage, current, power factor (p.f., Harmonic Distortion, and harmonic energy losses cost. The load is Induction Motor with Adjustable Speed Drive (ASD because the Induction Motor with Adjustable Speed Drive (ASD is one of electronic device causes harmonics. The voltage sources in this research are sine wave, square wave and harmonic order combinations of 3rd, 5th and 7th which can create from Schhafner Power Quality Analyzer.

  14. Relationships between Harmonic Characteristics and Different Types of Voltage Source

    Directory of Open Access Journals (Sweden)

    Syafruddin H

    2012-06-01

    Full Text Available This paper discusses about harmonic characteristics due to different types of voltage sources. Usually, the voltage source is sinusoidal. But in actual condition the load that receive voltage sources through the elements where the output voltage of element as input to the load is not pure sinusoidal, for example voltage source at  (PCC between transformer and linear load and nonlinear load. This research has been done with Schhafner Power Quality Analyzer and PM300 Power Quality Analyzer, was focused to all harmonic characteristics as power, voltage, current, power factor (p.f., Harmonic Distortion, and harmonic energy losses cost. The load is Induction Motor with Adjustable Speed Drive (ASD because the Induction Motor with Adjustable Speed Drive (ASD is one of electronic device causes harmonics. The voltage sources in this research are sine wave, square wave and harmonic order combinations of 3rd, 5th and 7th which can create from Schhafner Power Quality Analyzer.

  15. Probing Selenium-Ion Distributions and Changes in Redox-State at Biofilm/Mineral Interfaces by Coupling Long-period X-ray Standing Wave and XANES Measurements

    Science.gov (United States)

    Templeton, A. S.; Trainor, T. P.; Spormann, A. M.; Brown, G. E.

    2002-12-01

    Metal sorption and precipitation reactions at biological as well as mineral surfaces are important controls on metal speciation and bioavailability in natural environments. When highly hydrated biofilms form on mineral surfaces, numerous competitive and synergistic effects are predicted to occur. Experimentally, it is challenging to determine where the sorbed metal ions are localized, the relative affinity of the biological vs. mineral surface sites, or to monitor biomineralization reactions or changes in metal speciation that may also occur. A large part of the difficulty is due to the low concentrations of sorbed ions, the small length-scale of the biofilm-mineral interface, and the complex interplay between microbially-catalayzed redox transformations vs. sorption and/or transport processes. Long-period x-ray standing wave (XSW) techniques are well-suited to determining the vertical distribution of metal(oid) species within biofilms overlying mineral surfaces. We will discuss experiments where Se fluorescence yield profiles are used to compare the affinity of Burkholderia cepacia biofilms for binding Se(IV) and Se(VI) species relative to underlying alpha-Al2O3 substrates over three orders of magnitude in [Se]. In addition, we will discuss how coupling the XSW experiments to grazing-incidence, spatially-resolved Se K-edge XANES spectroscopy can be used to differentiate between the oxidation state of the Se complexes localized within the biofilm vs. the mineral surface. This approach is used to monitor changes in the relative distributions of Se(VI), Se(IV) and Se(0) species as a function of time and proximity to the mineral surface. The long-period XSW data show that selenite preferentially binds to the oxide surfaces, particularly at low [Se]. When B. cepacia is metabolically active, B. cepacia rapidly reduces a fraction of the Se(IV) to the red elemental Se form. In contrast, selenate is preferentially partitioned into the B. cepacia biofilms at all [Se] tested

  16. Automatic voltage imbalance detector

    Science.gov (United States)

    Bobbett, Ronald E.; McCormick, J. Byron; Kerwin, William J.

    1984-01-01

    A device for indicating and preventing damage to voltage cells such as galvanic cells and fuel cells connected in series by detecting sequential voltages and comparing these voltages to adjacent voltage cells. The device is implemented by using operational amplifiers and switching circuitry is provided by transistors. The device can be utilized in battery powered electric vehicles to prevent galvanic cell damage and also in series connected fuel cells to prevent fuel cell damage.

  17. Mixed voltage VLSI design

    Science.gov (United States)

    Panwar, Ramesh; Rennels, David; Alkalaj, Leon

    1993-01-01

    A technique for minimizing the power dissipated in a Very Large Scale Integration (VLSI) chip by lowering the operating voltage without any significant penalty in the chip throughput even though low voltage operation results in slower circuits. Since the overall throughput of a VLSI chip depends on the speed of the critical path(s) in the chip, it may be possible to sustain the throughput rates attained at higher voltages by operating the circuits in the critical path(s) with a high voltage while operating the other circuits with a lower voltage to minimize the power dissipation. The interface between the gates which operate at different voltages is crucial for low power dissipation since the interface may possibly have high static current dissipation thus negating the gains of the low voltage operation. The design of a voltage level translator which does the interface between the low voltage and high voltage circuits without any significant static dissipation is presented. Then, the results of the mixed voltage design using a greedy algorithm on three chips for various operating voltages are presented.

  18. Forest Stand Age

    Data.gov (United States)

    U.S. Geological Survey, Department of the Interior — Source data for forest stand age were obtained from the USDA Forest Inventory and Analysis (FIA) DataMart and were projected for future scenarios based on selected...

  19. Variable Attitude Test Stand

    Data.gov (United States)

    Federal Laboratory Consortium — The Variable Attitude Test Stand designed and built for testing of the V-22 tilt rotor aircraft propulsion system, is used to evaluate the effect of aircraft flight...

  20. NEO Test Stand Analysis

    Science.gov (United States)

    Pike, Cody J.

    2015-01-01

    A project within SwampWorks is building a test stand to hold regolith to study how dust is ejected when exposed to the hot exhaust plume of a rocket engine. The test stand needs to be analyzed, finalized, and fabrication drawings generated to move forward. Modifications of the test stand assembly were made with Creo 2 modeling software. Structural analysis calculations were developed by hand to confirm if the structure will hold the expected loads while optimizing support positions. These calculations when iterated through MatLab demonstrated the optimized position of the vertical support to be 98'' from the far end of the stand. All remaining deflections were shown to be under the 0.6'' requirement and internal stresses to meet NASA Ground Support Equipment (GSE) Safety Standards. Though at the time of writing, fabrication drawings have yet to be generated, but are expected shortly after.

  1. Voltage and Current Regulators Design of Power Converters in Islanded Microgrids based on State Feedback Decoupling

    DEFF Research Database (Denmark)

    Federico, de Bosio; de Sousa Ribeiro, Luiz Antonio; Freijedo Fernandez, Francisco Daniel

    2016-01-01

    In stand-alone microgrids based on voltage source inverters state feedback coupling between the capacitor voltage and inductor current degrades significantly the dynamics performance of voltage and current regulators. The decoupling of the controlled states is proposed, considering the limitations...... introduced by system delays. Moreover, a proportional resonant voltage controller is designed according to Nyquist criterion taking into account application requirements. Experimental tests performed in compliance with the UPS standards verify the theoretical analysis....

  2. Silicon-Germanium Voltage-Controlled Oscillator at 105 GHz

    Science.gov (United States)

    Wong, Alden; Larocca, Tim; Chang, M. Frank; Samoska, Lorene A.

    2011-01-01

    A group at UCLA, in collaboration with the Jet Propulsion Laboratory, has designed a voltage-controlled oscillator (VCO) created specifically for a compact, integrated, electronically tunable frequency generator useable for submillimeter- wave science instruments operating in extreme cold environments.

  3. Influence of the plasma on ICRF antenna voltage limits

    Science.gov (United States)

    Bobkov, V.; Noterdaeme, J.-M.; Wesner, F.; Wilhelm, R.; ASDEX Upgrade Team

    2003-03-01

    An ion cyclotron range of frequencies (ICRF) probe [F.W. Baity, G.C. Barber, V. Bobkov, R.H. Goulding, J.-M. Noterdaeme, D.W. Swain, in: 14th Topical Conference on Radiofrequency Power in Plasmas, Oxnard 2001, AIP Conference Proceedings 595, AIP, Melville, NY, 2001, p. 510] has been implemented to study voltage stand-off of the ICRF antennas on ASDEX Upgrade (AUG). The probe was operated at first in a test stand where features of high RF voltage operation in vacuum and plasma created by an ion source of the Hall type [Plasma Sources Sci. Technol. 8 (1999) R1] were studied. Vacuum arcs as well as ignition of high voltage glow discharge are candidate processes to explain voltage limits of the ICRF antennas. The setup on AUG was used to expose high RF voltages in real conditions of the tokamak scrape-off layer which are faced by the ICRF antennas. It is found that high voltage breakdown on the ICRF antenna is often correlated with ELM activity. The maximal RF voltage increased from shot to shot, i.e. the conditioning effect is observed. For the good-conditioned ICRF probe it was shown experimentally that the voltage limit can be increased while the rectified current is suppressed at the same time.

  4. Study on the linear entropy and quantum state transfer of trapped ions in a standing wave laser field%驻波激光场中囚禁离子的线性熵和量子态转移研究

    Institute of Scientific and Technical Information of China (English)

    王平; 吴俊芳; 廖庆洪; 鄢秋荣; 刘晔; 郑军

    2016-01-01

    运用量子纠缠和线性熵理论,研究了驻波激光场中囚禁离子的线性熵和量子态转移。讨论了相干角、离子的相对位相、离子与驻波激光场之间的耦合强度以及失谐量、Lamb-Dicke参数对离子线性熵的影响。结果表明,在一定的条件下可以实现囚禁离子的内态到振动态的相干转移,线性熵随时间的演化呈现非周期性的振荡行为。离子线性熵的最大值随着相干角、离子与激光场之间的耦合强度以及失谐量的增大而减小,随着Lamb-Dicke参数的增大而增大。并且可以通过调节驻波激光场来调节离子与驻波激光场之间的耦合强度和失谐量,从而达到对离子线性熵的控制与操纵,理论上提供了一种调控纠缠的方式。%Using quantum entanglement and linear entropy theory, the linear entropy and quantum state transfer of trapped ions in a standing wave laser field is studied. The effect of coherent angle, relative phase of ion, the coupling intensity and the detuning between the ion and the standing wave, Lamb-Dicke parameters on the line-ar entropy of the ion are discussed. The results show that the internal states of trapped ions can be transferred to the vibration state under certain conditions, the time evolution of linear entropy is a non periodic oscillatory be-havior. The maximum value of the ion linear entropy decreases with the increase of the coupling strength and de-tuning, and increases with the increase of the Lamb-Dicke parameter. And by adjusting laser standing wave field to regulate the coupling intensity and the detuning between the ion and the standing wave, so as to achieve the linear entropy of the ion manipulation and control, theory provides a way of linear entropy of ion regulation.

  5. PPT Thrust Stand

    Science.gov (United States)

    Haag, Thomas W.

    1995-01-01

    A torsional-type thrust stand has been designed and built to test Pulsed Plasma Thrusters (PPT's) in both single shot and repetitive operating modes. Using this stand, momentum per pulse was determined strictly as a function of thrust stand deflection, spring constant, and natural frequency. No empirical corrections were required. The accuracy of the method was verified using a swinging impact pendulum. Momentum transfer data between the thrust stand and the pendulum were consistent to within 1%. Following initial calibrations, the stand was used to test a Lincoln Experimental Satellite (LES-8/9) thruster. The LES-8/9 system had a mass of approximately 7.5 kg, with a nominal thrust to weight ratio of 1.3 x 10(exp -5). A total of 34 single shot thruster pulses were individually measured. The average impulse bit per pulse was 266 microN-s, which was slightly less than the value of 300 microN-s published in previous reports on this device. Repetitive pulse measurements were performed similar to ordinary steady-state thrust measurements. The thruster was operated for 30 minutes at a repetition rate of 132 pulses per minute and yielded an average thrust of 573 microN. Using average thrust, the average impulse bit per pulse was estimated to be 260 microN-s, which was in agreement with the single shot data. Zero drift during the repetitive pulse test was found to be approximately 1% of the measured thrust.

  6. Technological Aspects: High Voltage

    CERN Document Server

    Faircloth, D C

    2013-01-01

    This paper covers the theory and technological aspects of high-voltage design for ion sources. Electric field strengths are critical to understanding high-voltage breakdown. The equations governing electric fields and the techniques to solve them are discussed. The fundamental physics of high-voltage breakdown and electrical discharges are outlined. Different types of electrical discharges are catalogued and their behaviour in environments ranging from air to vacuum are detailed. The importance of surfaces is discussed. The principles of designing electrodes and insulators are introduced. The use of high-voltage platforms and their relation to system design are discussed. The use of commercially available high-voltage technology such as connectors, feedthroughs and cables are considered. Different power supply technologies and their procurement are briefly outlined. High-voltage safety, electric shocks and system design rules are covered.

  7. Stray voltage mitigation

    Energy Technology Data Exchange (ETDEWEB)

    Jamali, B.; Piercy, R.; Dick, P. [Kinetrics Inc., Toronto, ON (Canada). Transmission and Distribution Technologies

    2008-04-09

    This report discussed issues related to farm stray voltage and evaluated mitigation strategies and costs for limiting voltage to farms. A 3-phase, 3-wire system with no neutral ground was used throughout North America before the 1930s. Transformers were connected phase to phase without any electrical connection between the primary and secondary sides of the transformers. Distribution voltage levels were then increased and multi-grounded neutral wires were added. The earth now forms a parallel return path for the neutral current that allows part of the neutral current to flow continuously through the earth. The arrangement is responsible for causing stray voltage. Stray voltage causes uneven milk production, increased incidences of mastitis, and can create a reluctance to drink water amongst cows when stray voltages are present. Off-farm sources of stray voltage include phase unbalances, undersized neutral wire, and high resistance splices on the neutral wire. Mitigation strategies for reducing stray voltage include phase balancing; conversion from single to 3-phase; increasing distribution voltage levels, and changing pole configurations. 22 refs., 5 tabs., 13 figs.

  8. High voltage engineering

    CERN Document Server

    Rizk, Farouk AM

    2014-01-01

    Inspired by a new revival of worldwide interest in extra-high-voltage (EHV) and ultra-high-voltage (UHV) transmission, High Voltage Engineering merges the latest research with the extensive experience of the best in the field to deliver a comprehensive treatment of electrical insulation systems for the next generation of utility engineers and electric power professionals. The book offers extensive coverage of the physical basis of high-voltage engineering, from insulation stress and strength to lightning attachment and protection and beyond. Presenting information critical to the design, selec

  9. High voltage test techniques

    CERN Document Server

    Kind, Dieter

    2001-01-01

    The second edition of High Voltage Test Techniques has been completely revised. The present revision takes into account the latest international developments in High Voltage and Measurement technology, making it an essential reference for engineers in the testing field.High Voltage Technology belongs to the traditional area of Electrical Engineering. However, this is not to say that the area has stood still. New insulating materials, computing methods and voltage levels repeatedly pose new problems or open up methods of solution; electromagnetic compatibility (EMC) or components and systems al

  10. Mitigation of Unbalanced Voltage Sags and Voltage Unbalance in CIGRE Low Voltage Distribution Network

    OpenAIRE

    Mustafa, Ghullam; Bak-Jensen, Birgitte; Mahat, Pukar; Cecati, Carlo

    2013-01-01

    Any problem with voltage in a power network is undesirable as it aggravates the quality of the power. Power electronic devices such as Voltage Source Converter (VSC) based Static Synchronous Compensator (STATCOM) etc. can be used to mitigate the voltage problems in the distribution system. The voltage problems dealt with in this paper are to show how to mitigate unbalanced voltage sags and voltage unbalance in the CIGRE Low Voltage (LV) test network and net-works like this. The voltage unbala...

  11. Standing equine sinus surgery.

    Science.gov (United States)

    Barakzai, Safia Z; Dixon, Padraic M

    2014-04-01

    Trephination of the equine sinuses is a common surgical procedure in sedated standing horses. Standing sinus flap surgery has become increasingly popular in equine referral hospitals and offers several advantages over sinusotomy performed under general anesthesia, including reduced patient-associated risks and costs; less intraoperative hemorrhage, allowing better visualization of the operative site; and allows surgeons to take their time. Other minimally invasive surgical procedures include sinoscopic surgery, balloon sinuplasty, and transnasal laser sinonasal fenestration. Despite the procedure used, appropriate indications for surgery, good patient selection, and familiarity with regional anatomy and surgical techniques are imperative for good results. Copyright © 2014 Elsevier Inc. All rights reserved.

  12. Blower test stand; Luftleistungspruefstand

    Energy Technology Data Exchange (ETDEWEB)

    Anon.

    2003-04-01

    Blowers move air, but how much air? Extensive measurements are required for assessing blower performance in terms of the actual air flow volume. The most precise results are obtained in a test stand. [German] Luefter bewegen Luft. Aber wie viel wird tatsaechlich bewegt? Fuer die Bestimmung der tatsaechlichen Luftfoerderleistung ist ein grosser Messaufwand notwendig, die praezisesten Ergebnisse bringt ein Luftleistungsmessstand. (orig.)

  13. Principles of managing stands

    Science.gov (United States)

    David A. Marquis; Rodney Jacobs

    1989-01-01

    Forest stands are managed to achieve some combination of desired products or values. These products or values may include income and tangible benefits from timber production or fees for hunting rights and other recreational activities. The values may be intangible, such as the enjoyment of seeing wildlife or flowering plants, or the simple satisfaction of knowing that...

  14. Design of a New Water Load for S-band 750 kW Continuous Wave High Power Klystron Used in EAST Tokamak

    Institute of Scientific and Technical Information of China (English)

    LIU Liang; LIU Fukun; SHAN Jiafang; KUANG Guangli

    2007-01-01

    In order to test the klystrons operated at a frequency of 3.7 GHz in a continuous wave (CW) mode,a type of water load to absorb its power up to 750 kW is presented.The distilled water sealed with an RF ceramic window is used as the absorbent.At a frequency range of 70 MHz,the VSWR (Voltage Standing Wave Ratio) is below 1.2,and the rise in temperature of water is about 30℃ at the highest power level.

  15. Intensity improvement of shock waves induced by liquid electrical discharges

    Science.gov (United States)

    Liu, Yi; Li, Zhi-Yuan; Li, Xian-Dong; Liu, Si-Wei; Zhou, Gu-Yue; Lin, Fu-Chang

    2017-04-01

    When shock waves induced by pulsed electrical discharges in dielectric liquids are widely applied in industrial fields, it is necessary to improve the energy transfer efficiency from electrical energy to mechanical energy to improve the shock wave intensity. In order to investigate the effect of the plasma channel length created by the liquid electrical discharge on the shock wave intensity, a test stand of dielectric liquid pulsed electrical discharge is designed and constructed. The main capacitor is 3 μF, and the charging voltage is 0-30 kV. Based on the needle-needle electrode geometry with different gap distances, the intensities of shock waves corresponding to the electrical parameters, the relationship between the plasma channel length and the deposited energy, and the time-resolved observation of the plasma channel development by a high speed camera are presented and compared. The shock wave intensity is closely related to the power and energy dissipated into the plasma channel. The longer plasma channel and the quicker arc expansion can lead to a higher power and energy deposited into the plasma channel, which can activate a stronger shock wave.

  16. Voltage verification unit

    Science.gov (United States)

    Martin, Edward J.

    2008-01-15

    A voltage verification unit and method for determining the absence of potentially dangerous potentials within a power supply enclosure without Mode 2 work is disclosed. With this device and method, a qualified worker, following a relatively simple protocol that involves a function test (hot, cold, hot) of the voltage verification unit before Lock Out/Tag Out and, and once the Lock Out/Tag Out is completed, testing or "trying" by simply reading a display on the voltage verification unit can be accomplished without exposure of the operator to the interior of the voltage supply enclosure. According to a preferred embodiment, the voltage verification unit includes test leads to allow diagnostics with other meters, without the necessity of accessing potentially dangerous bus bars or the like.

  17. Surge currents and voltages at the low voltage power mains during lightning strike to a GSM tower

    Energy Technology Data Exchange (ETDEWEB)

    Markowska, Renata [Bialystok Technical University (Poland)], E-mail: remark@pb.edu.pl

    2007-07-01

    The paper presents the results of numerical calculations of lightning surge currents and voltages in the low voltage power mains system connected to a free standing GSM base station. Direct lightning strike to GSM tower was studied. The analysis concerned the current that flows to the transformer station through AC power mains, the potential difference between the grounding systems of the GSM and the transformer stations and the voltage differences between phase and PE conductors of the power mains underground cable at both the GSM and the transformer sides. The calculations were performed using a numerical program based on the electromagnetic field theory and the method of moments. (author)

  18. Controlled electromigration and oxidation of free-standing copper wires

    Science.gov (United States)

    Hauser, J. S.; Schwichtenberg, J.; Marz, M.; Sürgers, C.; Seiler, A.; Gerhards, U.; Messerschmidt, F.; Hensel, A.; Dittmeyer, R.; Löhneysen, H. v.; Hoffmann-Vogel, R.

    2016-12-01

    We have studied controlled electromigration (EM) in free-standing copper wires. Besides electrical characterization by voltage-current measurements, structural analyses have been performed by means of scanning electron microscopy and cross-sectional microprobe measurements. We have found that oxidation during the EM in air stabilizes the free-standing wire against uncontrolled blowing, making it possible to thin the conductive part of the wire down to a conductance of a few conductance quanta G_0=2e^2{/}h. The decisive influence of oxidation by air on the EM process was confirmed by control experiments performed under ultra-high vacuum conditions. In line with these findings, free-standing Au wires were difficult to thin down reproducibly to a conductance of a few G_0. Estimates of the local temperature in the free-standing wire are obtained from finite element method calculations.

  19. Cryocooled Josephson standards for AC voltage metrology

    Science.gov (United States)

    Durandetto, P.; Sosso, A.; Monticone, E.; Trinchera, B.; Fretto, M.; Lacquaniti, V.

    2017-05-01

    The Josephson effect is worldwide used as a basis for constant reference voltages in national metrological institutes and in calibration laboratories of industry. Research on Josephson voltage standards is aiming at a fundamental change also in the metrology of the volt for AC and arbitrary waveforms: programmable Josephson voltage standards converting a digital code into a quantum-accurate stepwise waveform are already available in primary laboratories and even more advanced standards for converting sub-nanosecond binary coded pulses into any arbitrary signal with quantum accuracy are now actively developed and tested. A new experimental setup based on a two-stage Gifford-McMahon cryocooler has been developed at INRiM for the operation of AC-Josephson voltage standards. Among its distinct features, the possibility of employing both the aforementioned techniques (programmable and pulsed Josephson voltage standards) is particularly interesting. Quantum-based AC voltage sine waves have been synthesized with both programmable and pulse-driven arrays, although their accuracy is still limited by thermal oscillations due to the cryocooler piston motion.

  20. Development of a 500 MHz high power RF test stand

    Institute of Scientific and Technical Information of China (English)

    PAN Wei-Min; SHA Peng; HUANG Tong-Ming; MA Qiang; WANG Guang-Wei; LIN Hai-Ying; ZHAO Guang-Yuan; SUN Yi; XU Bo; WANG Qun-Yao

    2012-01-01

    A flexible high power RF test stand has been designed and constructed at IHEP to test a variety of 500 MHz superconducting RF components for the upgrade project of the Beijing Electron Positron Collider (BEPC Ⅱ ),such as the input coupler,the higher order modes (HOMs) absorber and so on.A high power input coupler has been conditioned and tested with the RF power up to 250 kW in continuous wave (CW),traveling wave (TW) mode and 150 kW CW in standing wave (SW) mode.A prototype of the HOMs absorber has been tested to absorb power of 4.4 kW.An introduction of the test stand design,construction and high power tests is presented in this paper.

  1. Analysis and controller design for stand-alone VSIs in synchronous reference frame

    DEFF Research Database (Denmark)

    Ramezani, Malek; Li, Shuhui; Golestan, Saeed

    2017-01-01

    -by-step graphical analysis and design approach for a three-phase stand-alone VSI system in the dq reference frame, which provides a clear systematic decoupling process to design the inner- and outer-loop current and voltage controllers, respectively. The closed-loop d- and q-axis output impedances of the stand......The common practice for controlling the stand-alone voltage source inverters (VSIs) is to transform abc voltage and current signals to DC signals using the dq transformation, which makes it possible to control the new DC voltage and current signals just using simple proportional...... and hardware results verify the effectiveness of the graphic design and analysis strategy....

  2. Get up, Stand up

    Science.gov (United States)

    Melia, Ed

    2009-01-01

    Ignorance about dyslexia meant a miserable school experience for Barrie Hughes. He was in his 50s when he found the courage to stand up in front of a classroom of learners and admit he couldn't read. Barrie, who is now 59 and works for the parks department of Brighton and Hove Council, only began to learn how to read words in the last three years…

  3. Stand der Informationswissenschaft 2011

    Directory of Open Access Journals (Sweden)

    Ben Kaden

    2012-03-01

    Full Text Available Wandelnde Rahmenbedingungen stellen die Informationswissenschaft vor vielfältige Herausforderungen. So scheinen zwar digitale Technologien jedoch nicht deren Folgewirkungen auf die Disziplin und ihre Methoden in der Wechselbeziehung zur Gesellschaft umfassend berücksichtigt. Der Artikel dokumentiert die zähe Diskussion um den Stand und die Zukunft der Informationswissenschaft in Deutschland und formuliert Thesen zur Weiterentwicklung des Faches. Weiterhin werden Reaktionen auf diese Thesen in Clustern zusammengefasst und ein sich an diesen ausgerichteter Workshop dokumentiert.

  4. Coronal Waves and Oscillations

    Directory of Open Access Journals (Sweden)

    Nakariakov Valery M.

    2005-07-01

    Full Text Available Wave and oscillatory activity of the solar corona is confidently observed with modern imaging and spectral instruments in the visible light, EUV, X-ray and radio bands, and interpreted in terms of magnetohydrodynamic (MHD wave theory. The review reflects the current trends in the observational study of coronal waves and oscillations (standing kink, sausage and longitudinal modes, propagating slow waves and fast wave trains, the search for torsional waves, theoretical modelling of interaction of MHD waves with plasma structures, and implementation of the theoretical results for the mode identification. Also the use of MHD waves for remote diagnostics of coronal plasma - MHD coronal seismology - is discussed and the applicability of this method for the estimation of coronal magnetic field, transport coefficients, fine structuring and heating function is demonstrated.

  5. Multi-Purpose Test Stand

    Data.gov (United States)

    Federal Laboratory Consortium — The Multi-Purpose Test Stand is used for a wide variety of tests. The Stand is designed to be rotated through a range of fixed yaw positions to allow engines to be...

  6. Multi-Purpose Test Stand

    Data.gov (United States)

    Federal Laboratory Consortium — The Multi-Purpose Test Stand is used for a wide variety of tests. The Stand is designed to be rotated through a range of fixed yaw positions to allow engines to be...

  7. Plasma response to transient high voltage pulses

    Indian Academy of Sciences (India)

    S Kar; S Mukherjee

    2013-07-01

    This review reports on plasma response to transient high voltage pulses in a low pressure unmagnetized plasma. Mainly, the experiments are reviewed, when a disc electrode (metallic and dielectric) is biased pulsed negative or positive. The main aim is to review the electron loss in plasmas and particle balance during the negative pulse electrode biasing, when the applied pulse width is less than the ion plasma period. Though the applied pulse width is less than the ion plasma period, ion rarefaction waves are excited. The solitary electron holes are reviewed for positive pulsed bias to the electrode. Also the excitation of waves (solitary electron and ion holes) is reviewed for a metallic electrode covered by a dielectric material. The wave excitation during and after the pulse withdrawal, excitation and propagation characteristics of various electrostatic plasma waves are reviewed here.

  8. High Voltage Distribution

    Science.gov (United States)

    Norbeck, Edwin; Miller, Michael; Onel, Yasar

    2010-11-01

    For detector arrays that require 5 to 10 kV at a few microamps each for hundreds of detectors, using hundreds of HV power supplies is unreasonable. Bundles of hundreds of HV cables take up space that should be filled with detectors. A typical HV module can supply 1 ma, enough current for hundreds of detectors. It is better to use a single HV module and distribute the current as needed. We show a circuit that, for each detector, measures the current, cuts off the voltage if the current exceeds a set maximum, and allows the HV to be turned on or off from a control computer. The entire array requires a single HV cable and 2 or 3 control lines. This design provides the same voltage to all of the detectors, the voltage set by the single HV module. Some additional circuitry would allow a computer controlled voltage drop between the HV and each individual detector.

  9. High voltage engineering fundamentals

    CERN Document Server

    Kuffel, E; Hammond, P

    1984-01-01

    Provides a comprehensive treatment of high voltage engineering fundamentals at the introductory and intermediate levels. It covers: techniques used for generation and measurement of high direct, alternating and surge voltages for general application in industrial testing and selected special examples found in basic research; analytical and numerical calculation of electrostatic fields in simple practical insulation system; basic ionisation and decay processes in gases and breakdown mechanisms of gaseous, liquid and solid dielectrics; partial discharges and modern discharge detectors; and over

  10. Voltage-controlled nanoscale reconfigurable magnonic crystal

    Science.gov (United States)

    Wang, Qi; Chumak, Andrii V.; Jin, Lichuan; Zhang, Huaiwu; Hillebrands, Burkard; Zhong, Zhiyong

    2017-04-01

    A nanoscale reconfigurable magnonic crystal is designed using voltage-controlled perpendicular magnetic anisotropy (PMA) in ferromagnetic-dielectric heterostructures. A periodic array of gate metallic strips is placed on top of a MgO/Co structure in order to apply a periodic electric field and to modify the PMA in Co. It is numerically demonstrated that the introduction of PMA, which can be realized experimentally via applying a voltage, modifies the spin-wave propagation and leads to the formation of band gaps in the spin-wave spectrum. The band gaps can be controlled, i.e., it is possible to switch band gaps on and off within a few tens of nanoseconds. The width and the center frequency of the band gaps are defined by the applied voltage. Finally, it is shown that the introduction of PMA to selected, rather than to all gate strips allows for a predefined modification of the band-gap spectra. The proposed voltage-controlled reconfigurable magnonic crystal opens a way to low power consumption magnonic applications.

  11. Electromagnetic wave energy converter

    Science.gov (United States)

    Bailey, R. L. (Inventor)

    1973-01-01

    Electromagnetic wave energy is converted into electric power with an array of mutually insulated electromagnetic wave absorber elements each responsive to an electric field component of the wave as it impinges thereon. Each element includes a portion tapered in the direction of wave propagation to provide a relatively wideband response spectrum. Each element includes an output for deriving a voltage replica of the electric field variations intercepted by it. Adjacent elements are positioned relative to each other so that an electric field subsists between adjacent elements in response to the impinging wave. The electric field results in a voltage difference between adjacent elements that is fed to a rectifier to derive dc output power.

  12. Depth-Resolved Composition and Electronic Structure of Buried Layers and Interfaces in a LaNiO{sub 3}/SrTiO{sub 3} Superlattice from Soft- and Hard- X-ray Standing-Wave Angle-Resolved Photoemission

    Energy Technology Data Exchange (ETDEWEB)

    Eiteneer, D. [Department of Physics, University of California, Davis, California 95616 (United States); Materials Sciences Division, Lawrence Berkeley National Laboratory, Berkeley, California 94720 (United States); Pálsson, G.K., E-mail: gunnar.palsson@physics.uu.se [Department of Physics, University of California, Davis, California 95616 (United States); Materials Sciences Division, Lawrence Berkeley National Laboratory, Berkeley, California 94720 (United States); Nemšák, S. [Department of Physics, University of California, Davis, California 95616 (United States); Materials Sciences Division, Lawrence Berkeley National Laboratory, Berkeley, California 94720 (United States); Peter-Grünberg-Institut PGI-6, Forschungszentrum Julich, 52425 Julich (Germany); Gray, A.X. [Department of Physics, University of California, Davis, California 95616 (United States); Materials Sciences Division, Lawrence Berkeley National Laboratory, Berkeley, California 94720 (United States); Stanford Institute for Materials and Energy Sciences, SLAC National Accelerator Laboratory, Menlo Park, California 94025 (United States); Kaiser, A.M. [Department of Physics, University of California, Davis, California 95616 (United States); Materials Sciences Division, Lawrence Berkeley National Laboratory, Berkeley, California 94720 (United States); Son, J.; LeBeau, J. [Materials Department, University of California, Santa Barbara, California 93106 (United States); Conti, G. [Department of Physics, University of California, Davis, California 95616 (United States); Materials Sciences Division, Lawrence Berkeley National Laboratory, Berkeley, California 94720 (United States); and others

    2016-08-15

    Highlights: • Depth resolved electronic structure of LaNiO{sub 3}/SrTiO{sub 3} superlattices is measured. • The structure is determined by x-ray standing wave angle-resolved photoemission. • Similarity to the electronic structure of La{sub 0.7}Sr{sub 0.3}MnO{sub 3}/SrTiO{sub 3} is discussed. - Abstract: LaNiO{sub 3} (LNO) is an intriguing member of the rare-earth nickelates in exhibiting a metal-insulator transition for a critical film thickness of about 4 unit cells [Son et al., Appl. Phys. Lett. 96, 062114 (2010)]; however, such thin films also show a transition to a metallic state in superlattices with SrTiO{sub 3} (STO) [Son et al., Appl. Phys. Lett. 97, 202109 (2010)]. In order to better understand this transition, we have studied a strained LNO/STO superlattice with 10 repeats of [4 unit-cell LNO/3 unit-cell STO] grown on an (LaAlO{sub 3}){sub 0.3}(Sr{sub 2}AlTaO{sub 6}){sub 0.7} substrate using soft x-ray standing-wave-excited angle-resolved photoemission (SWARPES), together with soft- and hard- x-ray photoemission measurements of core levels and densities-of-states valence spectra. The experimental results are compared with state-of-the-art density functional theory (DFT) calculations of band structures and densities of states. Using core-level rocking curves and x-ray optical modeling to assess the position of the standing wave, SWARPES measurements are carried out for various incidence angles and used to determine interface-specific changes in momentum-resolved electronic structure. We further show that the momentum-resolved behavior of the Ni 3d e{sub g} and t{sub 2g} states near the Fermi level, as well as those at the bottom of the valence bands, is very similar to recently published SWARPES results for a related La{sub 0.7}Sr{sub 0.3}MnO{sub 3}/SrTiO{sub 3} superlattice that was studied using the same technique (Gray et al., Europhysics Letters 104, 17004 (2013)), which further validates this experimental approach and our conclusions. Our

  13. Excitation of voltage oscillations in an induction voltage adder

    Directory of Open Access Journals (Sweden)

    Nichelle Bruner

    2009-07-01

    Full Text Available The induction voltage adder is an accelerator architecture used in recent designs of pulsed-power driven x-ray radiographic systems such as Sandia National Laboratories’ Radiographic Integrated Test Stand (RITS, the Atomic Weapons Establishment’s planned Hydrus Facility, and the Naval Research Laboratory’s Mercury. Each of these designs relies on magnetic insulation to prevent electron loss across the anode-cathode gap in the vicinity of the adder as well as in the coaxial transmission line. Particle-in-cell simulations of the RITS adder and transmission line show that, as magnetic insulation is being established during a pulse, some electron loss occurs across the gap. Sufficient delay in the cavity pulse timings provides an opportunity for high-momentum electrons to deeply penetrate the cavities of the adder cells where they can excite radio-frequency resonances. These oscillations may be amplified in subsequent gaps, resulting in oscillations in the output power. The specific modes supported by the RITS-6 accelerator and details of the mechanism by which they are excited are presented in this paper.

  14. Tesla’s high voltage and high frequency generators with oscillatory circuits

    Directory of Open Access Journals (Sweden)

    Cvetić Jovan M.

    2016-01-01

    Full Text Available The principles that represent the basics of the work of the high voltage and high frequency generator with oscillating circuits will be discussed. Until 1891, Tesla made and used mechanical generators with a large number of extruded poles for the frequencies up to about 20 kHz. The first electric generators based on a new principle of a weakly coupled oscillatory circuits he used for the wireless signal transmission, for the study of the discharges in vacuum tubes, the wireless energy transmission, for the production of the cathode rays, that is x-rays and other experiments. Aiming to transfer the signals and the energy to any point of the surface of the Earth, in the late of 19th century, he had discovered and later patented a new type of high frequency generator called a magnifying transmitter. He used it to examine the propagation of electromagnetic waves over the surface of the Earth in experiments in Colorado Springs in the period 1899-1900. Tesla observed the formation of standing electromagnetic waves on the surface of the Earth by measuring radiated electric field from distant lightning thunderstorm. He got the idea to generate the similar radiation to produce the standing waves. On the one hand, signal transmission, i.e. communication at great distances would be possible and on the other hand, with more powerful and with at least three magnifying transmitters the wireless transmission of energy without conductors at any point of the Earth surface could also be achieved. The discovery of the standing waves on the surface of the Earth and the invention of the magnifying transmitter he claimed his greatest inventions. Less than two years later, at the end of 1901, he designed and started to build a much stronger magnifying transmitter on Long Island near New York City (the Wardenclyffe tower wishing to become a world telecommunication center. During the tower construction, he elaborated the plans for an even stronger transmitter based on

  15. Device for monitoring cell voltage

    Science.gov (United States)

    Doepke, Matthias [Garbsen, DE; Eisermann, Henning [Edermissen, DE

    2012-08-21

    A device for monitoring a rechargeable battery having a number of electrically connected cells includes at least one current interruption switch for interrupting current flowing through at least one associated cell and a plurality of monitoring units for detecting cell voltage. Each monitoring unit is associated with a single cell and includes a reference voltage unit for producing a defined reference threshold voltage and a voltage comparison unit for comparing the reference threshold voltage with a partial cell voltage of the associated cell. The reference voltage unit is electrically supplied from the cell voltage of the associated cell. The voltage comparison unit is coupled to the at least one current interruption switch for interrupting the current of at least the current flowing through the associated cell, with a defined minimum difference between the reference threshold voltage and the partial cell voltage.

  16. High voltage pulse generator

    Science.gov (United States)

    Fasching, George E.

    1977-03-08

    An improved high-voltage pulse generator has been provided which is especially useful in ultrasonic testing of rock core samples. An N number of capacitors are charged in parallel to V volts and at the proper instance are coupled in series to produce a high-voltage pulse of N times V volts. Rapid switching of the capacitors from the paralleled charging configuration to the series discharging configuration is accomplished by using silicon-controlled rectifiers which are chain self-triggered following the initial triggering of a first one of the rectifiers connected between the first and second of the plurality of charging capacitors. A timing and triggering circuit is provided to properly synchronize triggering pulses to the first SCR at a time when the charging voltage is not being applied to the parallel-connected charging capacitors. Alternate circuits are provided for controlling the application of the charging voltage from a charging circuit to be applied to the parallel capacitors which provides a selection of at least two different intervals in which the charging voltage is turned "off" to allow the SCR's connecting the capacitors in series to turn "off" before recharging begins. The high-voltage pulse-generating circuit including the N capacitors and corresponding SCR's which connect the capacitors in series when triggered "on" further includes diodes and series-connected inductors between the parallel-connected charging capacitors which allow sufficiently fast charging of the capacitors for a high pulse repetition rate and yet allow considerable control of the decay time of the high-voltage pulses from the pulse-generating circuit.

  17. 基于双音外差的电光相位调制器半波电压自校准测量方法∗%Two-tone optical hetero dyning metho d for the self-calibrated measurement of half-wave voltage of electro optic phase mo dulator

    Institute of Scientific and Technical Information of China (English)

    王恒; 张尚剑; 邹新海; 刘俊伟; 张雅丽; 李和平; 刘永

    2015-01-01

    High speed electrooptic phase modulators play very important roles in the high-speed optical fiber communication system, microwave photonic system, and coherent optical communication system, due to their advantages of bias voltage free and linear modulation. As an intrinsic parameter, the half-wave voltage of an electrooptic phase modulator has been characterized by using an electrical spectrum method and an optical spectrum method in the last two decades. The op-tical spectrum method is generally limited by the line-width of the laser source and the resolution of the available optical spectrum analyzer, while the electrical spectrum method requires the conversion from phase modulation to intensity modulation before photodetection, since a phase modulator generates a phase modulated optical signal with constant envelope. The major difficulty in the electrical spectrum method lies in the extra calibration for the responsivity fluctu-ation in the photodetection. In this paper, a novel self-calibrated measurement of half-wave voltage of electrooptic phase modulators is carried out based on the optical heterodyning between the two-tone phase modulated sidebands and the frequency-shifted carrier. The method achieves a self-calibration measurement, and avoids the effect of the responsivity fluctuation in the photodetection by setting a specific frequency relationship between the two-tone microwave signals. Moreover, it extends the measuring frequency range to the double bandwidth of photodetection and spectrum analysis. Compared with the optical spectrum method, the proposed method achieves very high frequency resolution measure-ment, and simultaneously avoids the line-width influence of laser source by use of two-tone heterodyning. Compared with the traditional electrical spectrum method, our method works under no small-signal assumption nor photodetection calibration, and eliminates the limits of electrical driving amplitude and operating wavelength. Moreover, it

  18. Voltage Regulators for Photovoltaic Systems

    Science.gov (United States)

    Delombard, R.

    1986-01-01

    Two simple circuits developed to provide voltage regulation for highvoltage (i.e., is greater than 75 volts) and low-voltage (i.e., is less than 36 volts) photovoltaic/battery power systems. Use of these circuits results in voltage regulator small, low-cost, and reliable, with very low power dissipation. Simple oscillator circuit controls photovoltaic-array current to regulate system voltage and control battery charging. Circuit senses battery (and system) voltage and adjusts array current to keep battery voltage from exceeding maximum voltage.

  19. Precise method for determining avalanche breakdown voltage of silicon photomultipliers

    Science.gov (United States)

    Chirikov-Zorin, I.

    2017-07-01

    A physically motivated method is proposed for determining the avalanche breakdown voltage of silicon photomultipliers (SiPM). The method is based on measuring the dependence of the relative photon detection efficiency (PDErel) on the bias voltage when one type of carriers (electron or hole) is injected into the avalanche multiplication zone of the p-n junction. The injection of electrons or holes from the base region of the SiPM semiconductor structure is performed using short-wave or long-wave light. At a low overvoltage (1-2 V) the detection efficiency is linearly dependent on the bias voltage; therefore, extrapolation to zero PDErel value determines the SiPM avalanche breakdown voltage with an accuracy within a few millivolts.

  20. Studying Voltage Transformer Ferroresonance

    Directory of Open Access Journals (Sweden)

    Hamid Radmanesh

    2012-09-01

    Full Text Available This study studies the effect of Circuit Breaker Shunt Resistance (CBSR, Metal Oxide Vaistor (MOV and Neutral earth Resistance (NR on the control of ferroresonance in the voltage transformer. It is expected that NR can controlled ferroresonance better than MOV and CBSR. Study has been done on a one phase voltage transformer rated 100 VA, 275 kV. The simulation results reveal that considering the CBSR and MOV exhibits a great mitigating effect on ferroresonance overvoltages, but these resistances cannot control these phenomena for all range of parameters. By applying NR to the system structure, ferroresonance has been controlled and its amplitude has been damped for all parameters values.

  1. Sound Waves Levitate Substrates

    Science.gov (United States)

    Lee, M. C.; Wang, T. G.

    1982-01-01

    System recently tested uses acoustic waves to levitate liquid drops, millimeter-sized glass microballoons, and other objects for coating by vapor deposition or capillary attraction. Cylindrical contactless coating/handling facility employs a cylindrical acoustic focusing radiator and a tapered reflector to generate a specially-shaped standing wave pattern. Article to be processed is captured by the acoustic force field under the reflector and moves as reflector is moved to different work stations.

  2. Standing Concertation Committee

    CERN Document Server

    HR Department

    2009-01-01

    Ordinary Meeting on 11 May 2009 The meeting of the Standing Concertation Committee held on 11 May 2009 was entirely dedicated to the preparation of the TREF meeting on 19 & 20 May 2009. The Committee took note, discussed and agreed on some clarifications on a number of documents and presentations that the Management planned to submit and/or present to TREF on the following subjects: • Personnel statistics 2008: J. Purvis presented the Personnel Statistics for 2008 prepared by HR Department. In line with the previous year, key messages were firstly, a general reduction in staff (2544 to 2400, - 6%), secondly, a reduction in administrative services personnel (from 422 to 387, - 8%) and thirdly, a marked increase in the number of Users and Unpaid Associates (from 8369 to 9140, + 9%) • Five-Yearly Review 2010: A series of draft documents were submitted for discussion, comprising an introductory document explaining the statutory basis for the following four document...

  3. Standing Concertation Committee

    CERN Multimedia

    HR Department

    2010-01-01

    Main issues examined at the meeting of 2 October 2009 The October 2009 meeting of the Standing Concertation Committee was entirely devoted to preparation of TREF’s meeting on 21-22 October. The Committee took note of, discussed and agreed on clarifications needed to some of the documents and presentations that the Management intended to submit and/or present to TREF on the following subjects: Equal opportunities The Committee took note of a preliminary report on equal opportunities at CERN drawn up by D. Chromek-Burckhart, the Equal Opportunities Officer, and T. Smith, Chairman of the Equal Opportunities Advisory Panel, containing in particular a proposal for a new process for resolving harassment conflicts. Technical analysis of the CERN Health Insurance Scheme - Actuary’s Report The Committee took note of a presentation by P. Charpentier, Chairman of the CERN Health Insurance Supervisory Board (CHIS Board), on the 2009 actuarial report on the CERN Health Insurance Scheme (CHIS). Th...

  4. Standing Concertation Commmittee

    CERN Multimedia

    HR Department

    2007-01-01

    Ordinary meeting on 2 november 2007 Extraordinary meeting on 12 November 2007 The main items discussed at the meetings of the Standing Concertation Committee on 2 November 2007 and 12 November included: Restaurants Supervisory Committee Report The committee took note of the report by the chairman of the Restaurants Supervisory Committee (RSC), T. Lagrange. In particular, it was recorded that, in Restaurant No. 1, the new kitchen and free flow arrangements had been inaugurated and all works had been commissioned on schedule in October 2007.The contractor, Novae, had taken over maintenance of the new kitchen. Some price increases were to be expected in the coming months due mainly to strong increases in the cost of basic ingredients. A problem with bad smells in the area of Restaurant No. 1 was being taken care of by tuning the ventilation system. The RSC wished to thank the management and staff of Restaurant No. 2 for their cooperation while Restaurant No 1 was ...

  5. Standing Concertation Committee

    CERN Multimedia

    HR Department

    2009-01-01

    The main items discussed at the meetings of the Standing Concertation Committee in the first quarter of 2009 included: Merit Appraisal and Recognition Scheme (MARS) 2009 exercise The committee took note of 2009 MARS ceiling guidelines giving the advancement budget by career path and amounting to approx 1.80% of the basic salary bill. To this will be added 250 steps CERN-wide, financed by savings from implementation of the international indemnity for 2007, 2008 and the first half of 2009. The specific Senior Staff Guidelines, including the proposed number of promotions from Career Path E to F, were also noted. The guidelines with respect to step distribution were also noted: the minima and maxima remain the same as in previous years. Compliance with the guidelines will continue to be monitored closely (more details, including a frequently asked questions section). It was also noted that Financial Awards (awards for extraordinary service and responsibility allowances) may b...

  6. STANDING CONCERTATION COMMMITTEE

    CERN Multimedia

    HR Department

    2008-01-01

    ORDINARY MEETING ON 27 FEBRUARY 2008 The main items discussed at the meetings of the Standing Concertation Committee on 27 February 2008 included: Short-term Saved Leave Scheme The committee noted that, by the end of February 2008, some 600 staff had subscribed to the short-term saved leave scheme: approx 58% had subscribed 1 slice, 14% two slices, 5% three slices and 23% four slices. Administrative Circular No. 4 (Rev. 4) - Unemployment Insurance Scheme The committee agreed to recommend Administrative Circular No. 4 (Rev. 4) - Unemployment Insurance Scheme to the Director-General for approval. Administrative Circular No. 30 (Rev. 2) - Financial benefits upon taking up appointment and termination of contract The committee agreed to recommend Administrative Circular No. 30 (Rev. 2) - Financial Benefits upon taking up appointment and termination of contract to the Director-General for approval. Progressive Retirement Programme The Progressive Retirement Programme (PRP) was extended for a further year to 3...

  7. STANDING CONCERTATION COMMMITTEE

    CERN Multimedia

    HR Department

    2008-01-01

    ORDINARY MEETING ON 27 FEBRUARY 2008 The main items discussed at the meetings of the Standing Concertation Committee on 27 February 2008 included: Short-term Saved Leave Scheme The committee noted that, by the end of February 2008, some 600 staff had subscribed to the short-term saved leave scheme: approx 58% had subscribed 1 slice, 14% two slices, 5% three slices and 23% four slices. Administrative Circular No. 4 (Rev. 4) - Unemployment Insurance Scheme The committee agreed to recommend Administrative Circular No. 4 (Rev. 4) - Unemployment Insurance Scheme to the Director-General for approval. Administrative Circular No. 30 (Rev. 2) - Financial benefits upon taking up appointment and termination of contract The committee agreed to recommend Administrative Circular No. 30 (Rev. 2) - Financial Benefits upon taking up appointment and termination of contract to the Director-General for approval. Progressive Retirement Programme The Progressive Retirement Programme (PRP) was extended for a further year to 3...

  8. Standing Concertation Committee

    CERN Multimedia

    HR Department

    2008-01-01

    ORDINARY MEETING ON 27 FEBRUARY 2008 The main items discussed at the meetings of the Standing Concertation Committee on 27 February 2008 included: Short-term Saved Leave Scheme The Committee noted that, by the end of February 2008, some 600 staff had enrolled in the short-term saved leave scheme: approx. 58% had signed up for 1 slice, 14% for two slices, 5% for three slices and 23% for four slices. Administrative Circular No. 4 (Rev. 4) - Unemployment Insurance Scheme The Committee agreed to recommend the Director-General to approve Administrative Circular No. 4 (Rev. 4) - Unemployment Insurance Scheme. Administrative Circular No. 30 (Rev. 2) - Financial benefits upon taking up appointment and termination of contract The Committee agreed to recommend the Director-General to approve Administrative Circular No. 30 (Rev. 2) - Financial Benefits upon taking up appointment and termination of contract. Progressive Retirement Programme The Progressive Retirement Programme (PR...

  9. INVESTIGATION ON EMI EFFECTS IN BANDGAP VOLTAGE REFERENCES

    OpenAIRE

    Fiori, Franco; Crovetti S., Paolo

    2002-01-01

    International audience; In this paper the susceptibility of integrated bandgap voltage references to Electromagnetic Interference (EMI) is investigated by on-chip measurements carried out on Kuijk and Tsividis bandgap circuits. These measurements highlight the offset in the reference voltage induced by continuous wave (CW) EMI and the complete failures which may be experienced by bandgap circuits. The role of the susceptibility of the startup circuit and of the operational amplifier which are...

  10. 负偏压离子鞘及气体压强影响表面波放电过程的粒子模拟%Particle-in-cell simulation on surface-wave discharge pro cess influenced by gas pressure and negative-biased voltage along ion sheath layer

    Institute of Scientific and Technical Information of China (English)

    陈兆权; 胡希伟; 殷志祥; 陈明功; 刘明海; 徐公林; 胡业林; 夏广庆; 宋晓; 贾晓芬

    2014-01-01

    Due to surface electromagnetic waves propagating along the dielectric-plasma interface, the application of surface-wave plasma (SWP) is limited in view of the fact that it is very difficult to realize metal sputtering by using negative-biased voltage in traditional SWP sources. Recently, this problem is overcome by a type of SWP source based on the guided wave in ion sheath layer driven by negative-biased voltage. And the plasma heating mechanism is originated from gas discharges excited by the local-enhanced electric field of surface plasmon polariton (SPP). However, the best discharge condition is not obtained because the influence factors affecting the discharge process studied is not clear. In this paper, the discharge mechanism of SWP ionization process influenced by gas pressure and negative-biased voltage along the ion sheath layer is investigated. The simulation method is by means of combining particle-in-cell (PIC) with Monte Carlo collision (MCC). Simulated results suggest that the values of negative-biased voltage and gas pressure can influence the thickness of ion sheath layer, the excitation of SPP, and the spatio-temporal conversion of wave mode, which further induces the different discharge performances. Moreover, the discussed analysis states that a better discharge performance can be obtained when approximately a negative-biased voltage of-200 V and a gas pressure of 40 Pa applied.%由于表面电磁波沿着介质-等离子体分界面传播,而很难通过对传统的表面波等离子体(SWP)源施加负偏压实现金属材料溅射,因此限制了SWP源的使用范围。近期,一种基于负偏压离子鞘导波的SWP源克服了这个问题,且其加热机理是表面等离激元(SPP)的局域增强电场激励气体放电产生。但是该SWP源放电过程的影响因素并未研究清晰,导致其最佳放电条件没有获得。本文采用粒子(PIC)和蒙特卡罗碰撞(MCC)相结合的模拟方法,探讨了负偏压离子

  11. Pulsed voltage electrospray ion source and method for preventing analyte electrolysis

    Science.gov (United States)

    Kertesz, Vilmos; Van Berkel, Gary

    2011-12-27

    An electrospray ion source and method of operation includes the application of pulsed voltage to prevent electrolysis of analytes with a low electrochemical potential. The electrospray ion source can include an emitter, a counter electrode, and a power supply. The emitter can include a liquid conduit, a primary working electrode having a liquid contacting surface, and a spray tip, where the liquid conduit and the working electrode are in liquid communication. The counter electrode can be proximate to, but separated from, the spray tip. The power system can supply voltage to the working electrode in the form of a pulse wave, where the pulse wave oscillates between at least an energized voltage and a relaxation voltage. The relaxation duration of the relaxation voltage can range from 1 millisecond to 35 milliseconds. The pulse duration of the energized voltage can be less than 1 millisecond and the frequency of the pulse wave can range from 30 to 800 Hz.

  12. Crush Test Abuse Stand

    Science.gov (United States)

    Collins, Jacob; Jeevarajan, Judith; Salinas, Mike

    2011-01-01

    The purpose of this system is to simulate an internal short on battery cells by causing deformation (a crushing force) in a cell without penetration. This is performed by activating a hydraulic cylinder on one side of a blast wall with a hydraulic pump located on the other. The operator can control the rate of the crush by monitoring a local pressure gauge connected to the hydraulic cylinder or a load cell digital display located at the hydraulic pump control area. The internal short simulated would be considered a worst-case scenario of a manufacturer fs defect. This is a catastrophic failure of a cell and could be a very destructive event. Fully charged cells are to have an internal short simulated at the center of the length of the cell (away from terminals). The crush can be performed with a .- to 1-in. (.0.6- to 2.5-cm) rod placed crossways to the cell axis, causing deformation of the cell without penetration. The OCV (open-circuit voltage) and temperature of the cells, as well as the pressure and crushing force, are recorded during the operation. Occurrence of an internal short accompanied by any visible physical changes such as venting, fires, or explosions is reported. Typical analytical data examined after the test would be plots of voltage, temperature, and pressure or force versus time. The rate of crushing force can be increased or decreased based on how fast the operator pumps the hydraulic pump. The size of cylinder used to compress the battery cell can be easily changed by adding larger or smaller fittings onto the end of the hydraulic cylinder based on the battery/cell size being tested. The cell is crushed remotely and videotaped, allowing the operator to closely monitor the situation from a safe distance.

  13. Geomagnetism and Induced Voltage

    Science.gov (United States)

    Abdul-Razzaq, W.; Biller, R. D.

    2010-01-01

    Introductory physics laboratories have seen an influx of "conceptual integrated science" over time in their classrooms with elements of other sciences such as chemistry, biology, Earth science, and astronomy. We describe a laboratory to introduce this development, as it attracts attention to the voltage induced in the human brain as it…

  14. High-voltage picoamperemeter

    Energy Technology Data Exchange (ETDEWEB)

    Bugl, Andrea; Ball, Markus; Boehmer, Michael; Doerheim, Sverre; Hoenle, Andreas; Konorov, Igor [Technische Universitaet Muenchen, Garching (Germany); Ketzer, Bernhard [Technische Universitaet Muenchen, Garching (Germany); Helmholtz-Institut fuer Strahlen- und Kernphysik, Bonn (Germany)

    2014-07-01

    Current measurements in the nano- and picoampere region on high voltage are an important tool to understand charge transfer processes in micropattern gas detectors like the Gas Electron Multiplier (GEM). They are currently used to e.g. optimize the field configuration in a multi-GEM stack to be used in the ALICE TPC after the upgrade of the experiment during the 2nd long shutdown of the LHC. Devices which allow measurements down to 1pA at high voltage up to 6 kV have been developed at TU Muenchen. They are based on analog current measurements via the voltage drop over a switchable shunt. A microcontroller collects 128 digital ADC values and calculates their mean and standard deviation. This information is sent with a wireless transmitting unit to a computer and stored in a root file. A nearly unlimited number of devices can be operated simultaneously and read out by a single receiver. The results can also be displayed on a LCD directly at the device. Battery operation and the wireless readout are important to protect the user from any contact to high voltage. The principle of the device is explained, and systematic studies of their properties are shown.

  15. An Analysis and Administration System for Cable Partial Discharge Data Based on Oscillatory Wave Voltage Method%基于振荡波电压法的电缆局部放电数据分析与管理系统

    Institute of Scientific and Technical Information of China (English)

    熊俊; 陆国俊

    2013-01-01

    基于振荡波电压法,考虑了局部放电信号的入射波形与反射波形时间限制、相似性、时频衰减性等因素,开发了一个电缆局部放电数据分析与管理系统。该系统与现场采集的原始数据兼容,具有定位算法精度高、数据分散性较小的特点,且系统能够实现电缆局部放电信息台账管理、状态评估与风险管理及打印报表等。%Based on the oscillatory wave voltage method, and taking the factors into account such as the time limit, similarity, time-frequency attenuation of incident wave and reflected wave in partial discharge signal, this paper develops an analysis and administration system for cable partial discharge data. The system is compatible with the original data collected from spot, and has the characteristics of high positioning accuracy and low data dispersion, and is able to realize the functions such as the account management of partial discharge informationt, condition assessment, risk management and report printing.

  16. Analysis and Improvement of Reflection-type Transverse Modulation Optical Voltage Sensors

    Institute of Scientific and Technical Information of China (English)

    LUO Sunan; YE Miaoyuan; XU Yan; CUI Ying

    2001-01-01

    Reflection-type transverse modulation optical voltage sensors, which employ reflection retarders to replace quarter-wave plates, are convenient for practical use. In previous literatures, the measured voltage was all applied to Bi4Ge3O12 crystal along the (110) direction for transverse modulation optical voltage sensor, and crystals are used as sensing materials. In this paper, reflection-type transverse modulation optical voltage sensor has been analyzed theoretically and a novel configuration in which the measured voltage is applied to a Bi4C-e3O12 crystal along the (001) direction with light wave passing through the crystal in the (110) direction has been proposed. According to this theoretical analysis, a novel optical voltage sensor, which can be used in a 220 kV optical fiber voltage transformer, has been designed and assembled. Experimental results showed that the linearity and the stability of the sensor during 24 hours can reach 0.3%.

  17. Output voltage calculations in double barrier magnetic tunnel junctions with asymmetric voltage behavior

    KAUST Repository

    Useinov, Arthur

    2011-10-22

    In this paper we study the asymmetric voltage behavior (AVB) of the tunnel magnetoresistance (TMR) for single and double barrier magnetic tunnel junctions (MTJs) in range of a quasi-classical free electron model. Numerical calculations of the TMR-V curves, output voltages and I-V characteristics for negative and positive values of applied voltages were carried out using MTJs with CoFeB/MgO interfaces as an example. Asymmetry of the experimental TMR-V curves is explained by different values of the minority and majority Fermi wave vectors for the left and right sides of the tunnel barrier, which arises due to different annealing regimes. Electron tunneling in DMTJs was simulated in two ways: (i) Coherent tunneling, where the DMTJ is modeled as one tunnel system and (ii) consecutive tunneling, where the DMTJ is modeled by two single barrier junctions connected in series. © 2012 Elsevier B.V. All rights reserved.

  18. Inductor Compensation in Three Phase PFC Control with Decoupling the Input Voltage and Bus Voltage

    Directory of Open Access Journals (Sweden)

    Luo Guang

    2016-01-01

    Full Text Available As the nonlinear structure of the boost ac/dc topology, the PFC is difficult to be controlled. The average state space theory has revealed that the choke current is determined by duty-ratio coupled with input voltage and bus voltage, which makes the high-performance sine-wave current track control more challenging. To remove disturbing variables and reduce the zero-crossing distortion, the decoupling control strategy is presented. Also, it is shown in this paper that the variable inductance has a great influence on PFC and THDI. As the inductor in boost converter varies with the current, a compensating coefficient of current is also proposed. The decoupling strategy and the inductor compensation strategy are implemented on a UPS with three phase input voltage. Numerical simulation and experimental results has indicated the high-performance of these control strategy.

  19. High voltage dc-dc converter with dynamic voltage regulation and decoupling during load-generated arcs

    Science.gov (United States)

    Shimer, Daniel W.; Lange, Arnold C.

    1995-01-01

    A high-power power supply produces a controllable, constant high voltage output under varying and arcing loads. The power supply includes a voltage regulator, an inductor, an inverter for producing a high frequency square wave current of alternating polarity, an improved inverter voltage clamping circuit, a step up transformer, an output rectifier for producing a dc voltage at the output of each module, and a current sensor for sensing output current. The power supply also provides dynamic response to varying loads by controlling the voltage regulator duty cycle and circuitry is provided for sensing incipient arc currents at the output of the power supply to simultaneously decouple the power supply circuitry from the arcing load. The power supply includes a plurality of discrete switching type dc--dc converter modules.

  20. Low voltage integrated optics electro-optical modulator applied to optical voltage transformer based on WLI technique

    Science.gov (United States)

    Santos, J. C.; Rubini, J.; Silva, L. P. C.; Caetano, R. E.

    2015-09-01

    The use of two electro-optical modulators linked in series, one for sensing and one for recovering signals, was formerly presented by some of the authors as a solution for interrogation of optical fiber sensor systems based on WLI method. A key feature required from such systems is that half-wave voltage (Vπ) of recovering modulator must be as small as possible. Aiming at meeting this requirement, in this paper it is presented the use of an unbalanced Michelson Interferometer implemented using an integrated optics component as recover interferometer in an optical voltage transformer intended for high voltage measurements.

  1. Mechanically robust microfluidics and bulk wave acoustics to sort microparticles

    Science.gov (United States)

    Dauson, Erin R.; Gregory, Kelvin B.; Greve, David W.; Healy, Gregory P.; Oppenheim, Irving J.

    2016-04-01

    Sorting microparticles (or cells, or bacteria) is significant for scientific, medical and industrial purposes. Research groups have used lithium niobate SAW devices to produce standing waves, and then to align microparticles at the node lines in polydimethylsiloxane (PDMS, silicone) microfluidic channels. The "tilted angle" (skewed) configuration is a recent breakthrough producing particle trajectories that cross multiple node lines, making it practical to sort particles. However, lithium niobate wafers and PDMS microfluidic channels are not mechanically robust. We demonstrate "tilted angle" microparticle sorting in novel devices that are robust, rapidly prototyped, and manufacturable. We form our microfluidic system in a rigid polymethyl methacrylate (PMMA, acrylic) prism, sandwiched by lead-zirconium-titanate (PZT) wafers, operating in through-thickness mode with inertial backing, that produce standing bulk waves. The overall configuration is compact and mechanically robust, and actuating PZT wafers in through-thickness mode is highly efficient. Moving to this novel configuration introduced new acoustics questions involving internal reflections, but we show experimental images confirming the intended nodal geometry. Microparticles in "tilted angle" devices display undulating trajectories, where deviation from the straight path increases with particle diameter and with excitation voltage to create the mechanism by which particles are sorted. We show a simplified analytical model by which a "phase space" is constructed to characterize effective particle sorting, and we compare our experimental data to the predictions from that simplified model; precise correlation is not expected and is not observed, but the important physical trends from the model are paralleled in the measured particle trajectories.

  2. Standing Concertation Committee

    CERN Multimedia

    2007-01-01

    ORDINARY MEETING ON 30 JANUARY 2007 The main items discussed at the meeting of the Standing Concertation Committee on 30 January 2007 included: Administrative Circular No. 26: with the introduction of the merit recognition system in the framework of the 5-yearly review of CERN employment conditions, Administrative Circular No. 26 has been revised. The Committee took note of the revised document which is being finalized for submission to the Director-General for approval in the near future. Technical analysis of CERN Health Insurance Scheme: the Committee was informed that a group has been set up by the Director-General to analyse the financial situation of the CERN Health Insurance Scheme in the short and long term, and to propose measures to ensure that the Scheme remains in financial balance, with adequate cover, over the medium term. The group's terms of reference and membership were communicated. Voluntary programmes It was announced that the programmes: 'part-time work as a pre-retirement mea...

  3. Standing Concertation Committee

    CERN Multimedia

    2007-01-01

    Ordinary meeting on 30 January 2007 The main items discussed at the meeting of the Standing Concertation Committee on 30 January 2007 included: Administrative Circular No. 26: with the introduction of the merit recognition system in the framework of the 5-yearly review of CERN employment conditions, Administrative Circular No. 26 has been revised. The committee took note of the revised document which is being finalized for submission to the Director-General for approval in the near future. Technical analysis of CERN Health Insurance Scheme: the Committee was informed that a group has been set up by the Director-General to analyse the financial situation of the CERN Health Insurance Scheme in the short and long term, and to propose measures to ensure that the Scheme remains in financial balance, with adequate cover, over the medium term. The group's terms of reference and membership were communicated. Voluntary programmes It was announced that the programmes: 'part-time work as a pre-retirement measure...

  4. Standing concertation commmittee

    CERN Multimedia

    HR Department

    2009-01-01

    MEETINGS ON 2 AND 9 DECEMBER 2008 The main items discussed at the meetings of the Standing Concertation Committee on 2 and 9 December 2008 included: Medical Service Report 2007 The Committee took note of the report by Dr. E. Reymond (see http://sc-me.web.cern.ch/sc-me/fr/indexFR.htm) and of a number of points raised during the discussion. It was noted that the number of professional accidents declined in 2007 (361 accidents) in comparison with 2006 (483), as well as their gravity and frequency. The CERN Medical Service carried out a study on cancer prevalence (number of cases) and incidence (new cases per year per 100000 people), between 1993 and 2007, which identified some prostate, breast and colorectal cancers, though less than in the two Host States. Specific preventive actions will be promoted by the CERN CHISboard and the Medical Service in this context as well as in other areas. The committee expressed its thanks to all members of the Medical Service for their work i...

  5. Standing Concertation Commmittee

    CERN Multimedia

    HR Department

    2007-01-01

    Ordinary meeting on 27 February 2007 The main items discussed at the meeting of the Standing Concertation Committee on 27 February 2007 included: Saved Leave Scheme (SLS): It was announced that a Management/Staff Association working group had been set up to discuss the Saved Leave Scheme (SLS): Members: M. Büttner, E. Chiaveri (chair), Ph. Defert, D. Klem, M. Vitasse, J.-M. Saint-Viteux. It was noted that the Staff Association was launching a questionnaire on SLS and distributed to all members of the personnel. Merit Recognition Guidelines : in the context of the new Merit Appraisal and Recognition Scheme (MARS), the committee took note of the CERN-wide 2007 Merit Recognition Guidelines, including the Frequently Asked Questions on HR Department's dedicated website. Information on CERN's medium and long-term plans (MTP-LTP)/Contract renewals/ External mobility The Committee took note of the information provided on CERN's MTP-LTP and of documentation distributed at the meeting by the Staff Associatio...

  6. Standing Concertation Committee

    CERN Multimedia

    HR Department

    2007-01-01

    ORDINARY MEETING ON 27 FEBRUARY 2007 The main items discussed at the meeting of the Standing Concertation Committee on 27 February 2007 included: Saved Leave Scheme (SLS): It was announced that a Management/Staff Association working group had been set up to discuss the Saved Leave Scheme (SLS): Members : M. Büttner, E. Chiaveri (chair), Ph. Defert, D. Klem, M. Vitasse, J.-M. Saint-Viteux. It was noted that the Staff Association was launching a questionnaire on SLS and distributed to all members of the personnel. Merit Recognition Guidelines: In the context of the new Merit Appraisal and Recognition Scheme (MARS), the committee took note of the CERN-wide 2007 Merit Recognition Guidelines, including the Frequently Asked Questions on HR Department's dedicated website. Information on CERN's medium and long-term plans (MTP-LTP)/Contract renewals/ External mobility The Committee took note of the information provided on CERN's MTP-LTP and of documentation distributed at the meeting by the Staff ...

  7. [Chile: Standing up again].

    Science.gov (United States)

    Reyes B, Humberto

    2010-03-01

    One of the biggest earthquakes recorded in human history has recently devastated a large part of the Chilean territory and, followed by a Tsunami, destroyed cities, seaports, fishermen's coves, bridges, and countryside houses. This cataclysm affected a large proportion of our population, leaving homeless families, no working tools for work places, hospitals, schools, public buildings, museums. However, the loss of human Uves was small compared to similar disasters. It destroyed part of the national heritage as well as damaged people's living conditions. A national movement started immediately to help and recover, and international resources, both human and technological were also set in motion. As after previous earthquakes in Chile, young M.D.'s and medical students were organized in voluntary groups backed by institutions or by their own organizations and went from large cities as Santiago and others to provide medical and psychological care to those in most need. Young members and students of other health professions (nurses, physical therapists, etc.) were included in these groups or worked in their own ones. National and international experience indicates that the forthcoming months require special care of psychological reactions and sequel (posttraumatic stress symptoms) and health consequences after water pollution, restrictions in housing and deteriorated sanitary conditions. Nevertheless, our country will stand up once more.

  8. OH Module Assembly Stand

    Energy Technology Data Exchange (ETDEWEB)

    Bolan, P.J.; /Fermilab

    1990-10-16

    There is an OR module assembly stand in use at IB4. This design has been approved by safety, as presented by Mike Foley, and has been successfully used. Another one is needed at the D-zero assembly building, but some modifications need to be made. This report will show that the new modified design is at least as strong, if not stronger, than the older IB4 design in every aspect. Since the weight distribution of the OR modules on the sling is indeterminate, this report compares three cases of support for the entire assembly: the lowest two beams only, the lowest four beams only, and all six beams. In each of these cases, the new design is stronger than the old design in maximum allowable weight. The ability of the the cradle to support the weight is also shown. For all of the failure conditions except for two, the cradle is stronger than the beams that it supports. In the two excepted situations, the calculated limit of the cradle is less than the beams it supports. This is because no credit is taken for the sling and strongback, which in reality will relieve much of the horizontal load.

  9. EUV Engineering Test Stand

    Energy Technology Data Exchange (ETDEWEB)

    Tichenor, D.A.; Kubiak, G.D.; Replogle, W.C.; Klebanoff, L.E.; Wronosky, J.B.; Hale, L.C.; Chapman, H.N.; Taylor, J.S.; Folta, J.A.; Montcalm, C.; Hudyma, R.M.

    2000-02-14

    The Engineering Test Stand (ETS) is an EUV laboratory lithography tool. The purpose of the ETS is to demonstrate EUV full-field imaging and provide data required to support production-tool development. The ETS is configured to separate the imaging system and stages from the illumination system. Environmental conditions can be controlled independently in the two modules to maximize EUV throughput and environmental control. A source of 13.4 nm radiation is provided by a laser plasma source in which a YAG laser beam is focused onto a xenon-cluster target. A condenser system, comprised of multilayer-coated mirrors and grazing-incidence mirrors, collects the EUV radiation and directs it onto a-reflecting reticle. A four-mirror, ring-field optical system, having a numerical aperture of 0.1, projects a 4x-reduction image onto the wafer plane. This design corresponds to a resolution of 70nm at a k{sub 1} of 0.52. The ETS is designed to produce full-field images in step: and-scan mode using vacuum-compatible, one-dimension-long-travel magnetically levitated stages for both reticle and wafer. Reticle protection is incorporated into the ETS design. This paper provides a system overview of the ETS design and specifications.

  10. Stand-up physics

    CERN Multimedia

    2009-01-01

    A CMS physicist and amateur stand up comic was named the winner of NESTA FameLab 2009. Tom Whyntie battled it out with nine others young scientists from across the UK to win the contest to find the country’s next top science communicator. Tom Whyntie with his prize money after the NESTA Famelab final.Tom Whyntie, who is currently doing his PhD on the CMS experiment, managed to persuade his supervisor to give him a few days off on 5 June so he could fly back to the UK for the final of NESTA FameLab 2009. In the competition, which has been dubbed ‘the X Factor for scientists’, he had just three minutes to explain a complex scientific idea to a panel of judges made up of high-profile science professionals. During the final, he captivated the audience with his talk about how finding nothing at the LHC, far from being a waste of £5 billion, would actually catalyse the next scientific revolution. It Whyntie’s own words: "If the L...

  11. High performance millimeter-wave microstrip circulators and isolators

    Science.gov (United States)

    Shih, Ming; Pan, J. J.

    1990-01-01

    Millimeter wave systems, phased array antennas, and high performance components all require wideband circulators (and isolators) to perform diplexing and switching, to improve isolation and Voltage Standing Wave Ratio (VSWR), and to construct IMPATT diode reflection amplifiers. Presently, most of the millimeter-wave circulators and isolators are available in the configurations of waveguide or stripline, both of which suffer from the shortcomings of bulky size/weight, narrow bandwidth, and poor compatibility with monolithic millimeter-wave integrated circuits (MMIC). MMW microstrip circulators/isolators can eliminate or improve these shortcomings. Stub-tuned microstrip circulator configuration were developed utilizing the electromagnetic fields perturbation technique, the adhesion problems of microstrip metallization on new ferrite substrate were overcome, the fabrication, assembly, packaging techniques were improved, and then successfully designed, fabricated a Ka band circulator which has isolation and return loss of greater than 16dB, insertion loss less than 0.7dB. To assess the steady and reliable performance of the circulator, a temperature cycling test was done over the range of -20 to +50 C for 3 continuous cycles and found no significant impact or variation of circulator performance.

  12. Deployment of low-voltage regulator considering existing voltage control in medium-voltage distribution systems

    Directory of Open Access Journals (Sweden)

    Hiroshi Kikusato

    2016-01-01

    Full Text Available Many photovoltaic (PV systems have been installed in distribution systems. This installation complicates the maintenance of all voltages within the appropriate range in all low-voltage distribution systems (LVDSs because the trends in voltage fluctuation differ in each LVDS. The installation of a low-voltage regulator (LVR that can accordingly control the voltage in each LVDS has been studied as a solution to this problem. Voltage control in a medium-voltage distribution system must be considered to study the deployment of LVRs. In this study, we installed LVRs in the LVDSs in which the existing voltage-control scheme cannot prevent voltage deviation and performed a numerical simulation by using a distribution system model with PV to evaluate the deployment of the LVRs.

  13. 电压暂降起始点与相位跳变对交流接触器影响的分析%Influence Analysis of Point-on-wave of Voltage Sag Initiation and Sag Phase Jump on Alternating Current Contactor

    Institute of Scientific and Technical Information of China (English)

    徐永海; 洪旺松; 兰巧倩

    2016-01-01

    电压暂降是电能质量中较为严重的问题之一,它对交流接触器等敏感设备造成了严重的影响。除电压暂降幅值和持续时间两个特征量会影响交流接触器的正常运行外,暂降的起始点、相位跳变等特征量也会对交流接触器的通断造成较大影响。文中进行了电压暂降对交流接触器影响的机理分析,建立了仿真模型,进行了暂降起始点、相位跳变对交流接触器磁通变化的影响分析与接触器通断分析;选取主流厂家生产的8个交流接触器进行了试验研究,得到了与机理分析相一致的结果,并绘制了电压暂降不同起始点与相位跳变特征量下交流接触器的耐受度曲线,可为交流接触器应对电压暂降问题提供基础数据,以减小电压暂降对其造成的影响,降低经济损失。%Voltage sag is one of the serious problems of power quality,which would cause severe impact on sensitive equipment such as alternating current (AC) contactors.In addition to voltage sag amplitude and duration which will affect the normal operation of AC contactors,the characteristics such as point-on-wave of sag initiation,sag phase jump also have significant impact on the switching of AC contactors.This paper makes a mechanism analysis of the impact of voltage sag on the AC contactor and builds a simulation model of the sag for analyzing the impact of point-on-wave of sag initiation and phase jump on the flux variation and switching of the AC contactor.Then eight AC contactors from mainstream manufacturers are studied and test results consistent with the results of the mechanism analysis are obtained.Finally,the AC contactor”s tolerance curves with different voltage sag characteristics of point-on-wave of sag initiation and the phase jump are plotted,which can provide basic data for the AC contactor to deal with the problem of voltage sag and reduce the corresponding economic loss.

  14. A control strategy for stand-alone wound rotor induction machine

    Energy Technology Data Exchange (ETDEWEB)

    Forchetti, D.G.; Garcia, G.O. [Grupo de Electronica Aplicada (GEA), Universidad Nacional de Rio Cuarto, X5804 BYA Rio Cuarto (Argentina); Solsona, J.A. [Instituto de Investigaciones en Ingenieria Electrica?Alfredo Desages?, Departamento de Ingenieria Electrica y de Computadoras, Universidad Nacional del Sur, Bahia Blanca (Argentina); Valla, M.I. [Laboratorio de Electronica Industrial, Control e Instrumentacion (LEICI), Facultad de Ingenieria, Universidad Nacional de La Plata, 1900 La Plata (Argentina)

    2007-02-15

    A control strategy to regulate the frequency and voltage of a stand-alone wound rotor induction machine is presented. This strategy allows the machine to work as a generator in stand-alone systems (without grid connection) with variable rotor speed. A stator flux-oriented control is proposed using the rotor voltages as actuation variables. Two cascade control loops are used to regulate the stator flux and the rotor currents. A closed loop observer is designed to estimate the machine flux which is necessary to implement these control loops. The proposed control strategy is validated through simulations with satisfactory results. (author)

  15. Analyzing of Dynamic Voltage Restorer in Series Compensation Voltage

    Directory of Open Access Journals (Sweden)

    Naser Parhizgar

    2012-02-01

    Full Text Available The Dynamic Voltage Restorer (DVR is a series-connected compensator to generate a controllable voltage to against the short-term voltage disturbances. The technique of DVR is an effective and cost competitive approach to improve voltage quality at the load side. This study presents a single-phase and threephase DVR system with reduced switch-count topology to protect the sensitive load against abnormal voltage conditions. Most basic function, the DVR configuration consist of a two level Voltage Source Converter (VSC, a dc energy storage device, a coupling transformer Connected in shunt with the ac system This study presents the application of Dynamic Voltage Restorer (DVR on power distribution systems for mitigation of voltage sag at critical loads. DVR is one of the compensating types of custom power devices. The DVR, which is based on forced-commutated Voltage Source Converter (VSC has been proved suitable for the task of compensating voltage sags/swells. Simulation results are presented to illustrate and understand the performances of DVR in supporting load voltages under voltage sags/swells conditions.

  16. High Voltage Charge Pump

    KAUST Repository

    Emira, Ahmed A.

    2014-10-09

    Various embodiments of a high voltage charge pump are described. One embodiment is a charge pump circuit that comprises a plurality of switching stages each including a clock input, a clock input inverse, a clock output, and a clock output inverse. The circuit further comprises a plurality of pumping capacitors, wherein one or more pumping capacitors are coupled to a corresponding switching stage. The circuit also comprises a maximum selection circuit coupled to a last switching stage among the plurality of switching stages, the maximum selection circuit configured to filter noise on the output clock and the output clock inverse of the last switching stage, the maximum selection circuit further configured to generate a DC output voltage based on the output clock and the output clock inverse of the last switching stage.

  17. Increased voltage photovoltaic cell

    Science.gov (United States)

    Ross, B.; Bickler, D. B.; Gallagher, B. D. (Inventor)

    1985-01-01

    A photovoltaic cell, such as a solar cell, is provided which has a higher output voltage than prior cells. The improved cell includes a substrate of doped silicon, a first layer of silicon disposed on the substrate and having opposite doping, and a second layer of silicon carbide disposed on the first layer. The silicon carbide preferably has the same type of doping as the first layer.

  18. Infra-Gravity Wave Generation by the Shoaling Wave Groups over Beaches

    Institute of Scientific and Technical Information of China (English)

    LIN Yu-Hsien; HWUNG Hwung-Hweng

    2012-01-01

    A physical parameter,μb,which was used to meet the forcing of primary short waves to be off-resonant before wave breaking,has been considered as an applicable parameter in the infra-gravity wave generation.Since a series of modulating wave groups for different wave conditions are performed to proceed with the resonant mechanism of infragravity waves prior to wave breaking,the amplitude growth of incident bound long wave is assumed to be simply controlled by the normalized bed slope,βb.The results appear a large dependence of the growth rate,α,of incident bound long wave,separated by the three-array method,on the normalized bed slope,βb.High spatial resolution of wave records enables identification of the cross-correlation between squared short-wave envelopes and infra-gravity waves.The crossshore structure of infra-gravity waves over beaches presents the mechanics of incident bound- and outgoing free long waves with the formation of free standing long waves in the nearshore region.The wave run-up and amplification of infra-gravity waves in the swash zone appear that the additional long waves generated by the breaking process would modify the cross-shore structure of free standing long waves.Finally,this paper would further discuss the contribution of long wave breaking and bottom friction to the energy dissipation of infra-gravity waves based on different slope conditions.

  19. Boost converter with combined control loop for a stand-alone photovoltaic battery charge system

    DEFF Research Database (Denmark)

    Mira Albert, Maria del Carmen; Knott, Arnold; Thomsen, Ole Cornelius

    2013-01-01

    The converter control scheme plays an important role in the performance of maximum power point tracking (MPPT) algorithms. In this paper, an input voltage control with double loop for a stand-alone photovoltaic system is designed and tested. The inner current control loop with high crossover...... is linearized at the maximum power point (MPP) and at the voltage and current source regions. A settling time under 1 ms is obtained which allows fast MPP tracking implementation....

  20. Spatiotemporal chaos involving wave instability

    Science.gov (United States)

    Berenstein, Igal; Carballido-Landeira, Jorge

    2017-01-01

    In this paper, we investigate pattern formation in a model of a reaction confined in a microemulsion, in a regime where both Turing and wave instability occur. In one-dimensional systems, the pattern corresponds to spatiotemporal intermittency where the behavior of the systems alternates in both time and space between stationary Turing patterns and traveling waves. In two-dimensional systems, the behavior initially may correspond to Turing patterns, which then turn into wave patterns. The resulting pattern also corresponds to a chaotic state, where the system alternates in both space and time between standing wave patterns and traveling waves, and the local dynamics may show vanishing amplitude of the variables.

  1. Phase linearity of the 914H coupled-cavity traveling wave tube

    Science.gov (United States)

    Kavanagh, Frank E.

    1994-01-01

    Tests of phase deviation from linearity were made on two 914H coupled-cavity traveling wave tubes (TWT). One tube had a voltage standing wave ratio (VSWR) of 2.4 and the other 1.4. The data showed that phase deviation is primarily a function of the amplitude and shape of the output VSWR. It was predicted that the low-VSWR tube would give a better system performance than the tube with a high VSWR. This prediction was confirmed by the Advanced Communications Technology Satellite (ACTS) system tests performed at the NASA Lewis Research Center. A possible improvement in the construction and stability of coupled-cavity TWT's is discussed.

  2. Mitigation of Voltage Sags in CIGRE Low Voltage Distribution Network

    DEFF Research Database (Denmark)

    Mustafa, Ghullam; Bak-Jensen, Birgitte; Mahat, Pukar;

    2013-01-01

    problems in the distribution system. The voltage problems dealt with in this paper are to show how to mitigate voltage sags in the CIGRE Low Voltage (LV) test network and networks like this. The voltage sags, for the tested cases in the CIGRE LV test network are mainly due to three phase faults....... The compensation of voltage sags in the different parts of CIGRE distribution network is done by using the four STATCOM compensators already existing in the test grid. The simulations are carried out in DIgSILENT power factory software version 15.0....

  3. Voltage Controlled Dynamic Demand Response

    DEFF Research Database (Denmark)

    Bhattarai, Bishnu Prasad; Bak-Jensen, Birgitte; Mahat, Pukar

    2013-01-01

    . An adaptive dynamic model has been developed to determine composite voltage dependency of an aggregated load on feeder level. Following the demand dispatch or control signal, optimum voltage setting at the LV substation is determined based on the voltage dependency of the load. Furthermore, a new technique...

  4. Charge-pump voltage converter

    Science.gov (United States)

    Brainard, John P.; Christenson, Todd R.

    2009-11-03

    A charge-pump voltage converter for converting a low voltage provided by a low-voltage source to a higher voltage. Charge is inductively generated on a transfer rotor electrode during its transit past an inductor stator electrode and subsequently transferred by the rotating rotor to a collector stator electrode for storage or use. Repetition of the charge transfer process leads to a build-up of voltage on a charge-receiving device. Connection of multiple charge-pump voltage converters in series can generate higher voltages, and connection of multiple charge-pump voltage converters in parallel can generate higher currents. Microelectromechanical (MEMS) embodiments of this invention provide a small and compact high-voltage (several hundred V) voltage source starting with a few-V initial voltage source. The microscale size of many embodiments of this invention make it ideally suited for MEMS- and other micro-applications where integration of the voltage or charge source in a small package is highly desirable.

  5. 基于电压调节的行波超声波电机转速模糊PID控制%Fuzzy PID Speed Control of Traveling Wave Ultrasonic Motor Using Voltage Amplitude Regulation

    Institute of Scientific and Technical Information of China (English)

    史敬灼; 张慧敏

    2011-01-01

    Accordance with ultrasonic motor's time-variable nonlinearity, a online adaptive correction based on fuzzy logic was presented. The special nature of ultrasonic motor's speed control were fully taken into account in designing fuzzy rules. The amplitude of driving voltage was used as the control parameter to realite the control method. The experiments indicate that the control characteristics are much better than that of PID controller.%针对超声波电机的时变非线性,给出了基于模糊逻辑的PID控制参数在线自适应校正方法.模糊规则设计中充分考虑了超声波电机转速控制的特殊性.采用驱动电压幅值作为控制量,实现了该控制方法.实验表明,控制性能优于PID控制器.

  6. Transient voltage sharing in series-coupled high voltage switches

    Directory of Open Access Journals (Sweden)

    Editorial Office

    1992-07-01

    Full Text Available For switching voltages in excess of the maximum blocking voltage of a switching element (for example, thyristor, MOSFET or bipolar transistor such elements are often coupled in series - and additional circuitry has to be provided to ensure equal voltage sharing. Between each such series element and system ground there is a certain parasitic capacitance that may draw a significant current during high-speed voltage transients. The "open" switch is modelled as a ladder network. Analy­sis reveals an exponential progression in the distribution of the applied voltage across the elements. Overstressing thus oc­curs in some of the elements at levels of the total voltage that are significantly below the design value. This difficulty is overcome by grading the voltage sharing circuitry, coupled in parallel with each element, in a prescribed manner, as set out here.

  7. Algebraically growing waves in ducts with sheared mean flow

    Science.gov (United States)

    Nayfeh, A. H.; Telionis, D. P.

    1974-01-01

    Analysis of the behavior of standing and traveling acoustic waves in a smooth duct with a fluid flow having a sheared mean velocity profile, when the waves grow algebraically as they travel along the duct axis. It is shown that standing waves growing algebraically with the axial distance cannot exist in a smooth duct when the duct wall have a finite resistance. The existence of traveling waves subject to the same law of growth is also dismissed under realistic flow conditions.

  8. Superconducting travelling wave ring with high gradient accelerating section

    Energy Technology Data Exchange (ETDEWEB)

    Avrakhov, P.; Solyak, N.; /Fermilab

    2007-06-01

    Use of a superconducting traveling wave accelerating (STWA) structure instead of a standing wave cavity has major advantages in increasing the accelerating gradient in the ILC. In contrast with standing wave cavity STWA requires feedback loop, which sends wave from the structure output to input, making a superconducting traveling wave ring (STWR). One or few input couplers need to excite STWR and compensate power dissipations due to beam loading. To control traveling wave regime in the structure two independent knobs can be used for tuning both resonant ring frequency and backward wave. We discuss two variants of the STWR with one and two feed couplers.

  9. Benchmarking of Voltage Sag Generators

    DEFF Research Database (Denmark)

    Yang, Yongheng; Blaabjerg, Frede; Zou, Zhixiang

    2012-01-01

    The increased penetration of renewable energy systems, like photovoltaic and wind power systems, rises the concern about the power quality and stability of the utility grid. Some regulations for Low Voltage Ride-Through (LVRT) for medium voltage or high voltage applications, are coming into force...... to guide these grid-connected distributed power generation systems. In order to verify the response of such systems for voltage disturbance, mainly for evaluation of voltage sags/dips, a Voltage Sag Generator (VSG) is needed. This paper evaluates such sag test devices according to IEC 61000 in order...... to provide cheaper solutions to test against voltage sags. Simulation and experimental results demonstrate that the shunt impedance based VSG solution is the easiest and cheapest one for laboratory test applications. The back-to-back fully controlled converter based VSG is the most flexible solution...

  10. Low voltage drop plasma switch for inverter and modulator applications

    Science.gov (United States)

    Goebel, D. M.; Poeschel, R. L.; Schumacher, R. W.

    1993-08-01

    A low forward voltage drop plasma switch has been developed for high-efficiency inverter and modulator applications. The switch, called the HOLLOTRON, is based on a grid-controlled, thermionic hollow-cathode discharge. A low forward voltage drop (10-20 V) is achieved by operating the hollow-cathode discharge in a static gas pressure of xenon. The dense plasma generated in the Ba-oxide dispenser hollow cathode is spread over a relatively large control grid area by a diverging magnetic field superimposed on the discharge. Interruption of the discharge current at high current densities (≳4 A/cm2) over the grid area is achieved by biasing the control grid sufficiently negative with respect to the plasma. The HOLLOTRON switch has demonstrated voltage stand-off of up to 20 kV, switching times of ≤0.3 μs, and pulse repetition frequencies of 20 kHz at 50% duty.

  11. Effects of Nonlinearities on Induced Voltages across Lumped Devices

    Directory of Open Access Journals (Sweden)

    Ziya Mazloom

    2011-01-01

    Full Text Available There have been many studies on induced currents and voltages along overhead conductors due to lightning flashes. In most of these studies lumped loads and components are connected only as line terminations [1]-[4]. In studies where series and shunt connected components are connected along the lines the effects of nonlinear components and effects are disregarded [5]-[8]. This is not always correct as nonlinear effects will introduce high frequencies in the system and affect the current and voltage wave distribution. In this paper the effects of series and shunt components and nonlinear phenomenon on a system representative of the Swedish electrified railway system will be investigated. It is seen how introduction of different linear and nonlinear components affect the propagating voltage wave forms.

  12. Coordinated Voltage Control of Distributed PV Inverters for Voltage Regulation in Low Voltage Distribution Networks

    DEFF Research Database (Denmark)

    Nainar, Karthikeyan; Pokhrel, Basanta Raj; Pillai, Jayakrishnan Radhakrishna

    2017-01-01

    This paper reviews and analyzes the existing voltage control methods of distributed solar PV inverters to improve the voltage regulation and thereby the hosting capacity of a low-voltage distribution network. A novel coordinated voltage control method is proposed based on voltage sensitivity...... analysis, which is simple for computation and requires moderate automation and communication infrastructure. The proposed method is suitable for a hierarchical control structure where a supervisory controller has the provision to adapt the settings of local PV inverter controllers for overall system...

  13. Heat-pump performance: voltage dip/sag, under-voltage and over-voltage

    Directory of Open Access Journals (Sweden)

    William J.B. Heffernan

    2014-12-01

    Full Text Available Reverse cycle air-source heat-pumps are an increasingly significant load in New Zealand and in many other countries. This has raised concern over the impact wide-spread use of heat-pumps may have on the grid. The characteristics of the loads connected to the power system are changing because of heat-pumps. Their performance during under-voltage events such as voltage dips has the potential to compound the event and possibly cause voltage collapse. In this study, results from testing six heat-pumps are presented to assess their performance at various voltages and hence their impact on voltage stability.

  14. Voltage Swells Improvement in Low Voltage Network Using Dynamic Voltage Restorer

    Directory of Open Access Journals (Sweden)

    R. Omar

    2011-01-01

    Full Text Available Problem statement: Voltage disturbances are the most common power quality problem due to the increased use of a large numbers of sophisticated electronic equipment in industrial distribution system. The voltage disturbances such as voltage sags, swells, harmonics, unbalance and flickers. High quality in the power supply is needed, since failures due to such disturbances usually have a high impact on production cost. There are many different solutions to compensate voltage disturbances but the use of a DVR is considered to be the most cost effective method. The objective of this study is to propose a new topology of a DVR in order to mitigate voltage swells using a powerful power custom device namely the Dynamic Voltage Restorer (DVR. Approach: New configuration of a DVR with an improvement of a controller based on direct-quadrature-zero method has been introduced to compensate voltage swells in the network. Results: The effectiveness of the DVR with its controller were verify using Matlab/Simulinks SimPower Toolbox and then implemented using 5KVA DVR experimental setup. Simulations and experimental results demonstrate the effective dynamic performance of the proposed configuration. Conclusion: The implimentation of the proposed DVR validate the capabilities in mitigating of voltage swells effectiveness.During voltage swells, the DVR injects an appropriate voltage to maintain the load voltage at its nominal value.

  15. Regular structures in 5CB liquid crystals under the joint action of ac and dc voltages

    Science.gov (United States)

    Aguirre, Luis E.; Anoardo, Esteban; Éber, Nándor; Buka, Ágnes

    2012-04-01

    A nematic liquid crystal with high, positive dielectric anisotropy (5CB) has been studied under the influence of the combined action of a dc and an ac electric field. Broad frequency, voltage, and cell thickness ranges were considered. Pattern morphologies were identified; the thresholds and critical wave numbers were measured and analyzed as a function of frequency, dc-to-ac voltage ratio, and thickness. The current-voltage characteristics were simultaneously detected.

  16. Isomerically Pure Tetramethylrhodamine Voltage Reporters.

    Science.gov (United States)

    Deal, Parker E; Kulkarni, Rishikesh U; Al-Abdullatif, Sarah H; Miller, Evan W

    2016-07-27

    We present the design, synthesis, and application of a new family of fluorescent voltage indicators based on isomerically pure tetramethylrhodamines. These new Rhodamine Voltage Reporters, or RhoVRs, use photoinduced electron transfer (PeT) as a trigger for voltage sensing, display excitation and emission profiles in the green to orange region of the visible spectrum, demonstrate high sensitivity to membrane potential changes (up to 47% ΔF/F per 100 mV), and employ a tertiary amide derived from sarcosine, which aids in membrane localization and simultaneously simplifies the synthetic route to the voltage sensors. The most sensitive of the RhoVR dyes, RhoVR 1, features a methoxy-substituted diethylaniline donor and phenylenevinylene molecular wire at the 5'-position of the rhodamine aryl ring, exhibits the highest voltage sensitivity to date for red-shifted PeT-based voltage sensors, and is compatible with simultaneous imaging alongside green fluorescent protein-based indicators. The discoveries that sarcosine-based tertiary amides in the context of molecular-wire voltage indicators prevent dye internalization and 5'-substituted voltage indicators exhibit improved voltage sensitivity should be broadly applicable to other types of PeT-based voltage-sensitive fluorophores.

  17. 振幅相位调制驻波光场中冷却原子的动力学局域%Dynamical investigation on momentum spread of two-level atom by an amplitude-modulated and phase-modulated standing light wave

    Institute of Scientific and Technical Information of China (English)

    王中结; 陆同兴; 路轶群

    2001-01-01

    In this paper the model of two-level atomic momentum spread in amplitude- and phase-modulated standing light wave was investigated. this is a nonlinear quantum pendulum driven by a time-dependent perterbation with two frequencies. This system shows chaotic behaviour in the classical limit. The system exists the characteristic of dynamical localization for the same parameters as that in the classical model correspoinding to it. Localization length of the system with two incommensurate perturbing frequency is much larger than that of the system with one perturbing frequency.%分析了二能级原子在振幅相位调制驻波场作用下动量扩散模型,这是一个双频参数激励的非线性量子单摆模型。这个系统在经典极限下表现混沌行为,在相同参数条件下,这个系统具有动力学局域特征,具有两个不可约频率扰动的系统的局域长度要比单个频率扰动时大得多。

  18. Standing sausage modes in coronal loops with plasma flow

    CERN Document Server

    Li, Bo; Xia, Li-Dong; Yu, Hui

    2014-01-01

    Magnetohydrodynamic waves are important for diagnosing the physical parameters of coronal plasmas. Field-aligned flows appear frequently in coronal loops.We examine the effects of transverse density and plasma flow structuring on standing sausage modes trapped in coronal loops, and examine their observational implications. We model coronal loops as straight cold cylinders with plasma flow embedded in a static corona. An eigen-value problem governing propagating sausage waves is formulated, its solutions used to construct standing modes. Two transverse profiles are distinguished, one being the generalized Epstein distribution (profile E) and the other (N) proposed recently in Nakariakov et al.(2012). A parameter study is performed on the dependence of the maximum period $P_\\mathrm{max}$ and cutoff length-to-radius ratio $(L/a)_{\\mathrm{cutoff}}$ in the trapped regime on the density parameters ($\\rho_0/\\rho_\\infty$ and profile steepness $p$) and flow parameters (magnitude $U_0$ and profile steepness $u$). For e...

  19. 基于Prony算法的固有频率法输电线路故障定位%Fault Location of High Voltage Power Transmission Lines Using Travelling Wave Natural Frequency Based on Prony Method

    Institute of Scientific and Technical Information of China (English)

    徐俊明; 魏文伟; 夏沛

    2011-01-01

    When a short circuit fault of transmission lines happened, it will produce transient state travelling waves.The frequency spectra of the travelling waves is a fundamental characteristic frequency, called natural frequencies. Accurate extracting the natural frequencies, which contains informations of position of fault,is able to realize fault location.As a traditional method, Fast Fourier Transform algorithm has not a high frequency resolution and cannot extract the natural frequencies precisely. In allusion to this problem, the paper brings forward applying the Prony Method, which has high precision of fitting, to extract the natural frequencies. The results of simulations by PSCAD and MATLAB show that Prony method can accurate extract the natural frequencies, and the location result is more accurate than Fast Fourier Transform method.%输电线路发生短路故障时,将会产生故障暂态行波.行波在频域上表现为一定的谐波形式,称为行波的固有频率.固有频率包含故障点位置信息,准确提取固有频率能实现输电线路的故障定位.针对传统的FFT算法频域分辨率不高,不能准确提取行波固有频率的问题,提出利用拟合精度较高的Prony算法提取固有频率.EMTDC联合MATLAB仿真结果表明,Prony算法能准确提取固有频率,较FFT方法有更高的定位精度.

  20. Self-standing corrugated Ag and Au-nanorods for plasmonic applications

    DEFF Research Database (Denmark)

    Habouti, S.; Mátéfi-Tempfli, M.; Solterbeck, C.-H.;

    2011-01-01

    We use home-made Si-supported anodized alumina thin film templates for the electrodeposition of large area self-standing Ag- and Au-nanorod (Au-NR) arrays. The deposition conditions chosen, i.e. electrolyte composition and deposition voltage, lead to a corrugated rod morphology, particularly for ...

  1. MOSFET Loss Evaluation for a Low-Power Stand-Alone Photovoltaic-LED System

    DEFF Research Database (Denmark)

    Mira Albert, Maria del Carmen; Knott, Arnold; Andersen, Michael A. E.

    2015-01-01

    This paper presents a performance evaluation and comparison of state-of-the-art low voltage Si MOSFETs for a stand-alone photovoltaic-LED Light to Light (LtL) system. The complete system is formed by two cascaded converters that will be optimized for a determined solar irradiation and LED...

  2. Voltage source inverters for high power, variable-voltage DC power sources

    Energy Technology Data Exchange (ETDEWEB)

    Chen, Z. [Department of Engineering and Technology, De Montfort University, Queens Building, The Gateway, Leicester, LE1 9BH, (United Kingdom); Spooner, E. [School of Engineering, University of Durham, Science Laboratories, South Rd, Durham, DRI 3LE, (United Kingdom)

    2001-09-01

    The paper discusses the applications of voltage source inverter (VSI) based power electronic systems for interfacing variable-voltage DC sources to the grid. A variable-speed wind power conversion system is used for illustration, where the VSI-based interface needs to convert a variable DC voltage to a nearly constant AC voltage with high-quality power. The power control principles of VSI are described. Various system configurations and switching strategies are examined by analysis, simulation and experimental methods. It is shown that better utilisation of semiconductors and more flexible control may be achieved by using a separately controlled DC link, rather than a directly connected VSI that has to operate at a lower modulation ratio at higher power. In some cases, multipulse inverter structures may be preferred, despite higher component count, because of reduced switching losses, fault tolerance and the absence of filters. The solutions developed in the study could be applied at a different scale to other renewable energy sources, such as wave or solar photovoltaic devices. (Author)

  3. Voltage and Pressure Scaling of Streamer Dynamics in a Helium Plasma Jet With N2 CO-Flow (Postprint)

    Science.gov (United States)

    2014-08-14

    increased applied voltage. These observed differences in the 2-D scaling properties of ionization wave sustained cathode directed streamer propagation in...streamer propagation in helium versus air16,17 are responsible for the observed differences in the propagation of ionization wave sustained streamer...increase quadratically with increased applied voltage. These observed differences in the 2-D scaling properties of ionization wave sustained cathode

  4. Free-standing chiral plasmonics

    Science.gov (United States)

    Leong, Eunice Sok Ping; Deng, Jie; Wu, Siji; Khoo, Eng Huat; Liu, Yan Jun

    2014-11-01

    Chiral plasmonic nanostructures offer the ability to achieve strong optical circular dichroism (CD) activity over a broad spectral range, which has been challenging for chiral molecules. Chiral plasmonic nanostructures have been extensively studied based on top-down and bottom-up fabrication techniques. Particularly, in the top-down electron-beam lithography, 3D plasmonic nanostructure fabrication involves layer-by-layer patterning and complex alignment, which is time-consuming and causes many defects in the structures. Here, we present a free-standing 3D chiral plamonic nanostructures using the electron-beam lithography technique with much simplified fabrication processes. The 3D chiral plasmonic nanostructures consist of a free-standing ultrathin silicon nitride membrane with well-aligned L-shape metal nanostructures on one side and disk-shape ones on the other side. The free-standing membrane provides an ultra-smooth metal/dielectric interface and uniformly defines the gap between the upper and lower layers in an array of chiral nanostructures. Such free-standing chiral plasmonic nanostructures exhibit strong CD at optical frequencies, which can be engineered by simply changing the disk size on one side of the membrane. Experimental results are in good agreement with the finite-difference time-domain simulations. Such free-standing chiral plasmonics holds great potential for chirality analysis of biomolecules, drugs, and chemicals.

  5. Voltage Dependence of Supercapacitor Capacitance

    Directory of Open Access Journals (Sweden)

    Szewczyk Arkadiusz

    2016-09-01

    Full Text Available Electronic Double-Layer Capacitors (EDLC, called Supercapacitors (SC, are electronic devices that are capable to store a relatively high amount of energy in a small volume comparing to other types of capacitors. They are composed of an activated carbon layer and electrolyte solution. The charge is stored on electrodes, forming the Helmholtz layer, and in electrolyte. The capacitance of supercapacitor is voltage- dependent. We propose an experimental method, based on monitoring of charging and discharging a supercapacitor, which enables to evaluate the charge in an SC structure as well as the Capacitance-Voltage (C-V dependence. The measurement setup, method and experimental results of charging/discharging commercially available supercapacitors in various voltage and current conditions are presented. The total charge stored in an SC structure is proportional to the square of voltage at SC electrodes while the charge on electrodes increases linearly with the voltage on SC electrodes. The Helmholtz capacitance increases linearly with the voltage bias while a sublinear increase of total capacitance was found. The voltage on SC increases after the discharge of electrodes due to diffusion of charges from the electrolyte to the electrodes. We have found that the recovery voltage value is linearly proportional to the initial bias voltage value.

  6. A PC-controlled voltage pulse generator for electroanalytical applications

    Science.gov (United States)

    Heredia-López, Francisco J.; Góngora-Alfaro, José L.; Alvarez-Cervera, Fernando J.; Bata-García, José Luis

    1997-04-01

    We present the design of a voltage pulse generator controlled by an IBM or compatible AT Personal Computer (PC) capable of synthesizing some of the voltage pulse wave forms commonly used in electrochemical studies. The included signals are: differential pulse voltametry, differential normal pulse voltametry, and differential pulse amperometry. Additionally, a triangular wave form and a constant-voltage signal, used in the pretreatment of carbon fiber microelectrodes for neurochemical analysis, are also available. Operating the generator imposes a minimum of restrictions on the specification of the duration, amplitude, and type of wave shapes. Low-cost PC-based design allows for compatibility, portability, and versatility. The operating ranges of the wave form parameters for the three voltametric signals are: initial voltage, -0.9-+0.9 V; step amplitude, 0.1-900 mV; period, 6 ms-60 s; measuring pulse amplitude, 0.1-900 mV; measuring pulse duration, 2 ms-20 s; prepulse duration, 2 ms-20 s. In the electrode pretreatment mode, the operating ranges are: amplitude, 0-±5 V; duration, unlimited; frequency, 15-240 Hz. The generator uses its own time base for the generation of all signals, thereby rendering it independent of processor clock speed or power-line frequency. The results of the experimental evaluation indicate that the system is accurate within ±10% of the expected values, taking into account the errors associated with the signal synthesis and the digitizing process. The maximum achievable scan rate is 500 V/s, and the highest frequency for the triangular wave form is 240 Hz. Therefore, the pulse generator could be used for fast cyclic voltametry (FCV). FCV and other wave forms could be added through software modules, without any hardware changes. We conclude that the PC-based electrochemistry pulse generator represents an economical and flexible alternative for electroanalytical applications.

  7. Analogue Divider by Averaging a Triangular Wave

    Science.gov (United States)

    Selvam, Krishnagiri Chinnathambi

    2017-08-01

    A new analogue divider circuit by averaging a triangular wave using operational amplifiers is explained in this paper. The triangle wave averaging analog divider using operational amplifiers is explained here. The reference triangular waveform is shifted from zero voltage level up towards positive power supply voltage level. Its positive portion is obtained by a positive rectifier and its average value is obtained by a low pass filter. The same triangular waveform is shifted from zero voltage level to down towards negative power supply voltage level. Its negative portion is obtained by a negative rectifier and its average value is obtained by another low pass filter. Both the averaged voltages are combined in a summing amplifier and the summed voltage is given to an op-amp as negative input. This op-amp is configured to work in a negative closed environment. The op-amp output is the divider output.

  8. The cathode test stand for the DARHT second-axis

    Energy Technology Data Exchange (ETDEWEB)

    Fortgang, C.; Monroe, M.; Prono, D. [Los Alamos National Lab., NM (United States); Hudson, C.; Macy, D.; Moy, K. [Bechtel Nevada, Santa Barbara, CA (United States)

    1998-12-31

    The injector for the DARHT second-axis injector will use an 8-in. thermionic dispenser cathode. Because the cathode is relatively large and requires a large amount of heat (5 kW) there are certain engineering issues that need to be addressed, before the DARHT injector reaches the final design stage. The Cathode Test Stand (CTS) will be used to address those concerns. The CTS is a new facility, presently under construction. The CTS will consist of a high-voltage pulse modulator, a high-vacuum diode test-chamber, and a short beam-transport section with diagnostics. This paper discusses the status of the project.

  9. FREE STANDING FILM OF POLYANILINE

    Institute of Scientific and Technical Information of China (English)

    WAN Meixiang; CAO Yong; LI Junchao; ZHOU Weixia; LI Suzhen

    1991-01-01

    A free standing film of polyaniline as large as 18cm×18cm×0.002cm can be obtained by evaporation of a solution of the chemically synthesized base in NMP. Its structure was examined by the elemental analysis, IR, U.V.-visible spectra, XPS, DSC, SEM and X-ray scattering and its conducting behavior as well as electrochemical properties were studied. Results show that the composition, structure of main chain, physical properties of the free standing tilm of polyaniline is similar to that of the powder. However, some differences in its electronic structure, conductivity at room temperature and potential of redox couple between the free standing film and powder are observed,which may be due to cross-linking of the film of polyaniline.

  10. 21 CFR 880.6990 - Infusion stand.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Infusion stand. 880.6990 Section 880.6990 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES....6990 Infusion stand. (a) Identification. The infusion stand is a stationary or movable stand...

  11. A Versatile Control Scheme For Dynamic Voltage Restorer To Limit Downstream Fault Currents

    Directory of Open Access Journals (Sweden)

    A.Nagendra

    2014-12-01

    Full Text Available The Dynamic Voltage Restorer (DVR is a custom power device utilized to counteract voltage sags. It injects controlled three-phase ac voltages in series with the supply voltage, subsequent to voltage sag, to enhance voltage quality by adjusting the voltage magnitude, wave shape, and phase angle. The DVR is conventionally bypassed during a downstream fault to prevent potential adverse impacts on the fault and to protect the DVR components against the fault current. This paper proposes an augmented control strategy for the DVR that provides:1 voltage-sag compensation under balanced and unbalanced conditions and 2 a fault current interruption (FCI function. This paper introduces and evaluates an auxiliary control strategy for downstream fault current interruption in a radial distribution line by means of a dynamic voltage restorer (DVR. The proposed controller supplements the voltage-sag compensation control of the DVR. It does not require phaselocked loop and independently controls the magnitude and phase angle of the injected voltage for each phase. Fast least error squares digital filters are used to estimate the magnitude and phase of the measured voltages and effectively reduce the impacts of noise, harmonics, and disturbances on the estimated phasor parameters, and this enables effective fault current interrupting even under arcing fault conditions. The performance of the DVR for fault current interruption is analyzed by using MATLAB/SIMULINK software.

  12. Efficient counter-propagating wave acoustic micro-particle manipulation

    Science.gov (United States)

    Grinenko, A.; Ong, C. K.; Courtney, C. R. P.; Wilcox, P. D.; Drinkwater, B. W.

    2012-12-01

    A simple acoustic system consisting of a pair of parallel singe layered piezoelectric transducers submerged in a fluid used to form standing waves by a superposition of two counter-propagating waves is reported. The nodal positions of the standing wave are controlled by applying a variable phase difference to the transducers. This system was used to manipulate polystyrene micro-beads trapped at the nodal positions of the standing wave. The demonstrated good manipulation capability of the system is based on a lowering of the reflection coefficient in a narrow frequency band near the through-thickness resonance of the transducer plates.

  13. Characterisation of charge voltage of lead-acid batteries: application to the charge control strategy in photovoltaic systems

    Energy Technology Data Exchange (ETDEWEB)

    Vela, N. [CIEMAT-DER, Madrid (Spain). Laboratorio de Energia Solar Fotovoltaica; Aguilera, J. [Universidad de Jaen (Spain). Escuela Politecnica Superior

    2006-12-15

    In stand-alone photovoltaic (PV) systems, charge controllers prevent excessive battery overcharge by interrupting or limiting the current flow from the PV array to the battery when the battery becomes fully charged. Charge regulation is most often accomplished by limiting the battery voltage to a predetermined value or cut-off voltage, higher than the gassing voltage. These regulation voltages are dependent on the temperature and battery charge current. An adequate selection of overcharge cut-off voltage for each battery type and operating conditions would maintain the highest battery state of charge without causing significant overcharge thus improving battery performance and reliability. To perform this work, a sample of nine different lead-acid batteries, typically used in stand-alone PV systems including vented and sealed batteries with 2 V cells and monoblock configurations have been selected. This paper presents simple mathematical expressions fitting two charge characteristic voltages: the gassing voltage (V{sub g}) and the end-of charge voltage (V{sub fc}) as function of charge current and temperature for the tested batteries. With these expressions, we have calculated V{sub g} and V{sub fc} at different current rates. An analysis of the different values obtained is presented here focusing in the implication in control strategies of batteries in stand-alone PV systems. (author)

  14. Ultra-low-voltage design of energy-efficient digital circuits

    CERN Document Server

    Reynders, Nele

    2015-01-01

    This book focuses on increasing the energy-efficiency of electronic devices so that portable applications can have a longer stand-alone time on the same battery. The authors explain the energy-efficiency benefits that ultra-low-voltage circuits provide and provide answers to tackle the challenges which ultra-low-voltage operation poses. An innovative design methodology is presented, verified, and validated by four prototypes in advanced CMOS technologies. These prototypes are shown to achieve high energy-efficiency through their successful functionality at ultra-low supply voltages.

  15. Developing de Broglie Wave

    Directory of Open Access Journals (Sweden)

    Zheng-Johansson J. X.

    2006-10-01

    Full Text Available The electromagnetic component waves, comprising together with their generating oscillatory massless charge a material particle, will be Doppler shifted when the charge hence particle is in motion, with a velocity v, as a mere mechanical consequence of the source motion. We illustrate here that two such component waves generated in opposite directions and propagating at speed c between walls in a one-dimensional box, superpose into a traveling beat wave of wavelength Λd=vcΛ and phase velocity c2/v+v which resembles directly L. de Broglie’s hypothetic phase wave. This phase wave in terms of transmitting the particle mass at the speed v and angular frequency Ωd= 2πv/Λd, with Λd and Ωd obeying the de Broglie relations, represents a de Broglie wave. The standing-wave function of the de Broglie (phase wave and its variables for particle dynamics in small geometries are equivalent to the eigen-state solutions to Schrödinger equation of an identical system.

  16. Burnout : de stand van zaken

    NARCIS (Netherlands)

    Taris, T.; Houtman, I.L.D.; Schaufeli, W.

    2013-01-01

    Dit artikel geeft een overzicht van de stand van zaken in het onderzoek naar burnout. Burnout is een syndroom van extreme vermoeidheid (uitputting), afstand nemen van het werk (distantie) en weinig vertrouwen in het eigen kunnen (verminderde competentie), waarbij de oorzaken voor deze aspecten geleg

  17. A3 TEST STAND CONSTRUCTION

    Science.gov (United States)

    2008-01-01

    THIS IMAGE SHOWS THE DEVELOPMENT AND CONSTRUCTION OF THE A3 TEST STAND IN SUPPORT OF THE ARES/CLV UPPER STAGE ENGINE AT STENNIS SPACE CENTER, MISSISSIPPI. THIS IMAGE IS EXTRACTED FROM A HIGH DEFINITION VIDEO FILE AND IS THE HIGHEST RESOLUTION AVAILABLE.

  18. A3 TEST STAND CONSTRUCTION

    Science.gov (United States)

    2008-01-01

    THIS IMAGE SHOWS THE DEVELOPMENT AND CONSTRUCTION OF THE A3 TEST STAND IN SUPPORT OF THE ARES/CLV UPPER STAGE ENGINE AT STENNIS SPACE CENTER, MISSISSIPPI. THIS IMAGE IS EXTRACTED FROM A HIGH DEFINITION VIDEO FILE AND IS THE HIGHEST RESOLUTION AVAILABLE.

  19. Burnout : de stand van zaken

    NARCIS (Netherlands)

    Taris, T.; Houtman, I.L.D.; Schaufeli, W.

    2013-01-01

    Dit artikel geeft een overzicht van de stand van zaken in het onderzoek naar burnout. Burnout is een syndroom van extreme vermoeidheid (uitputting), afstand nemen van het werk (distantie) en weinig vertrouwen in het eigen kunnen (verminderde competentie), waarbij de oorzaken voor deze aspecten

  20. Scattering of oblique waves by permeable vertical flexible membrane wave barriers

    CERN Document Server

    Koley, Santanu

    2016-01-01

    The interaction of obliquely incident surface gravity waves with a vertical flexible permeable membrane wave barrier is investigated in the context of three-dimensional linear wave-structure interaction theory. A general formulation for wave interaction with permeable submerged vertical membrane is given. The analytic solution of the physical problem is obtained by using eigenfunction expansion method, and boundary element method has been used to get the numerical solution. In the boundary element method, since the boundary condition on the membrane is not known in advance, membrane motions and velocity potentials are solved simultaneously. From the general formulation of the submerged membrane barrier, the performance of bottom-standing, surface-piercing and fully extended membrane wave barriers are analyzed for various wave and structural parameters. It is found that the efficiency of the submerged, surface-piercing and bottom-standing membrane wave barriers can be enhanced in waves for certain design condi...

  1. High-Voltage, Asymmetric-Waveform Generator

    Science.gov (United States)

    Beegle, Luther W.; Duong, Tuan A.; Duong, Vu A.; Kanik, Isik

    2008-01-01

    The shapes of waveforms generated by commercially available analytical separation devices, such as some types of mass spectrometers and differential mobility spectrometers are, in general, inadequate and result in resolution degradation in output spectra. A waveform generator was designed that would be able to circumvent these shortcomings. It is capable of generating an asymmetric waveform, having a peak amplitude as large as 2 kV and frequency of several megahertz, which can be applied to a capacitive load. In the original intended application, the capacitive load would consist of the drift plates in a differential-mobility spectrometer. The main advantage to be gained by developing the proposed generator is that the shape of the waveform is made nearly optimum for various analytical devices requiring asymmetric-waveform such as differential-mobility spectrometers. In addition, this waveform generator could easily be adjusted to modify the waveform in accordance with changed operational requirements for differential-mobility spectrometers. The capacitive nature of the load is an important consideration in the design of the proposed waveform generator. For example, the design provision for shaping the output waveform is based partly on the principle that (1) the potential (V) on a capacitor is given by V=q/C, where C is the capacitance and q is the charge stored in the capacitor; and, hence (2) the rate of increase or decrease of the potential is similarly proportional to the charging or discharging current. The proposed waveform generator would comprise four functional blocks: a sine-wave generator, a buffer, a voltage shifter, and a high-voltage switch (see Figure 1). The sine-wave generator would include a pair of operational amplifiers in a feedback configuration, the parameters of which would be chosen to obtain a sinusoidal timing signal of the desired frequency. The buffer would introduce a slight delay (approximately equal to 20 ns) but would otherwise

  2. Investigation of Power Factor on Harmonic Effect due to Types of Voltage Source

    Directory of Open Access Journals (Sweden)

    C.B. Risnidar

    2011-01-01

    Full Text Available This paper discussed about power factor on harmonic effect due to types of voltage source. Usually, the voltage source is sinusoidal. But in actual condition the load that has voltage sources through the elements where the output voltage of element as input to load is not pure sinusoidal, for example at Power of Common Coupling (PCC between transformer and linear load and nonlinear load. The research has been done with Schhafner Power Quality Analyzer and was focused to power factor (p.f., Total Harmonic Distortion (THD, and harmonic energy losses cost from measurement where load is Induction motor and Adjustable Speed Drive (ASD. As voltage source in this research are sine wave, square wave and combinations of 3rd, 5th and 7th harmonic order like harmonic 313, and harmonic 357.

  3. A study of nanoparticle manipulation using ultrasonic standing waves

    NARCIS (Netherlands)

    Neer, P.L.M.J. van; Rasidovic, A.; Volker, A.W.F.

    2013-01-01

    There has been considerable interest in the noninvasive manipulation of particles in dispersions during the last 15 years. The manipulation techniques based on acoustic radiation forces are particularly interesting as they allow for the manipulation of particles based on their density, compressibili

  4. Scaling-up ultrasound standing wave enhanced sedimentation filters

    OpenAIRE

    Prest, Jeff E.; Treves Brown, Bernard J.; Fielden, Peter R.; Wilkinson, Stephen J.; Hawkes, Jeremy J.

    2015-01-01

    Particle concentration and filtration is a key stage in a wide range of processing industries and also one that can be present challenges for high throughput, continuous operation. Here we demonstrate some features which increase the efficiency of ultrasound enhanced sedimentation and could enable the technology the potential to be scaled up. In this work, 20 mm piezoelectric plates were used to drive 100 mm high chambers formed from single structural elements. The coherent structural resonan...

  5. A non-contact technique for evaluation of elastic structures at large stand-off distances: applications to classification of fluids in steel vessels.

    Science.gov (United States)

    Kaduchak, G; Sinha, D N; Lizon, D C; Kelecher, M J

    2000-01-01

    A novel technique for non-contact evaluation of structures in air at large stand-off distances (on the order of several meters) has been developed. It utilizes a recently constructed air-coupled, parametric acoustic array to excite the resonance vibrations of elastic, fluid-filled vessels. The parametric array is advantageous for NDE applications in that it is capable of producing a much narrower beamwidth and broader bandwidth than typical devices that operate under linear acoustic principles. In the present experiments, the array operates at a carrier frequency of 217 kHz, and the sound field several meters from the source is described spectrally by the envelope of the drive voltage. An operating bandwidth of more than 25 kHz at a center frequency of 15 kHz is demonstrated. For the present application, the array is used to excite vibrations of fluid-filled, steel containers at stand-off distances of greater than 3 m. The vibratory response of a container is detected with a laser vibrometer in a monostatic configuration with the acoustic source. By analyzing the change in the response of the lowest order, antisymmetric Lamb wave as the interior fluid loading conditions of the container are changed, the fluid contained within the steel vessel is classified.

  6. Effects of Electrode Material on the Voltage of a Tree-Based Energy Generator.

    Directory of Open Access Journals (Sweden)

    Zhibin Hao

    Full Text Available The voltage between a standing tree and its surrounding soil is regarded as an innovative renewable energy source. This source is expected to provide a new power generation system for the low-power electrical equipment used in forestry. However, the voltage is weak, which has caused great difficulty in application. Consequently, the development of a method to increase the voltage is a key issue that must be addressed in this area of applied research. As the front-end component for energy harvesting, a metal electrode has a material effect on the level and stability of the voltage obtained. This study aimed to preliminarily ascertain the rules and mechanisms that underlie the effects of electrode material on voltage. Electrodes of different materials were used to measure the tree-source voltage, and the data were employed in a comparative analysis. The results indicate that the conductivity of the metal electrode significantly affects the contact resistance of the electrode-soil and electrode-trunk contact surfaces, thereby influencing the voltage level. The metal reactivity of the electrode has no significant effect on the voltage. However, passivation of the electrode materials markedly reduces the voltage. Suitable electrode materials are demonstrated and recommended.

  7. Voltage Sensors Monitor Harmful Static

    Science.gov (United States)

    2009-01-01

    A tiny sensor, small enough to be worn on clothing, now monitors voltage changes near sensitive instruments after being created to alert Agency workers to dangerous static buildup near fuel operations and avionics. San Diego s Quasar Federal Systems received a Small Business Innovation Research (SBIR) contract from Kennedy Space Center to develop its remote voltage sensor (RVS), a dime-sized electrometer designed to measure triboelectric changes in the environment. One of the unique qualities of the RVS is that it can detect static at greater distances than previous devices, measuring voltage changes from a few centimeters to a few meters away, due to its much-improved sensitivity.

  8. Measurement system for determination of current-voltage characteristics of PV modules

    Science.gov (United States)

    Idzkowski, Adam; Walendziuk, Wojciech; Borawski, Mateusz; Sawicki, Aleksander

    2015-09-01

    The realization of a laboratory stand for testing photovoltaic panels is presented here. The project of the laboratory stand was designed in SolidWorks software. The aim of the project was to control the electrical parameters of a PV panel. For this purpose a meter that measures electrical parameters i.e. voltage, current and power, was realized. The meter was created with the use of LabJack DAQ device and LabVIEW software. The presented results of measurements were obtained in different conditions (variable distance from the source of light, variable tilt angle of the panel). Current voltage characteristics of photovoltaic panel were created and all parameters could be detected in different conditions. The standard uncertainties of sample voltage, current, power measurements were calculated. The paper also gives basic information about power characteristics and efficiency of a solar cell.

  9. Unequal Input Voltages Distribution Between the Serial Connected Halfbridges

    Directory of Open Access Journals (Sweden)

    Radovan Ovcarcik

    2006-01-01

    Full Text Available This paper describes a topology of DC-DC converter consisting in two serial connected half-bridges. Secondary circuit is realized like a conventional full-wave rectifier. The main advantage of this topology is the possibility of dividing the input voltage between the half-bridges. The converter is controlled using the phase-shift modulation, which allows a ZVSoperation mode. The voltage unbalance between the inputs causes an important problem of the presented topology. It is necessary to avoid it by the control algorithm, which is described in the text. The practical results show a zero voltage switching technique and the limits of the chosen topology and of the control.

  10. Low Voltage Power Supply Incorporating Ceramic Transformer

    CERN Document Server

    Imori, M

    2007-01-01

    A low voltage power supply provides the regulated output voltage of 1 V from the supply voltage around 48 V. The low voltage power supply incorporates a ceramic transformer which utilizes piezoelectric effect to convert voltage. The ceramic transformer isolates the secondary from the primary, thus providing the ground isolation between the supply and the output voltages. The ceramic transformer takes the place of the conventional magnetic transformer. The ceramic transformer is constructed from a ceramic bar and does not include any magnetic material. So the low voltage power supply can operate under a magnetic field. The output voltage is stabilized by feedback. A feedback loop consists of an error amplifier, a voltage controlled oscillator and a driver circuit. The amplitude ratio of the transformer has dependence on the frequency, which is utilized to stabilize the output voltage. The low voltage power supply is investigated on the analogy of the high voltage power supply similarly incorporating the cerami...

  11. Modular High Voltage Power Supply

    Energy Technology Data Exchange (ETDEWEB)

    Newell, Matthew R. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2017-05-18

    The goal of this project is to develop a modular high voltage power supply that will meet the needs of safeguards applications and provide a modular plug and play supply for use with standard electronic racks.

  12. Mechanisms of Fluid-Mud Interactions Under Waves

    Science.gov (United States)

    2011-09-30

    lutocline that occurred when the lutocline was within a few centimeters of the water surface. This three-wave instability led to generation of subharmonic ... Subharmonic standing waves on the surface of the lutocline, generated by a long surface wave train traveling from left to right in the figure...Superharmonic waves (hard to see) and the turbulent structures (middle left) within the subharmonic waves are also present. Theoretical modeling—We

  13. Phytoclimate of winter rye stands

    Energy Technology Data Exchange (ETDEWEB)

    Wittchen, U. [Federal Biological Research Centre for Agriculture and Forestry, Kleinmachnow (Germany); Chmielewski, F.M. [Humboldt-Univ. of Berlin, Faculty of Agriculture and Horticulture, Berlin (Germany)

    2005-04-01

    The present study describes the microclimate within a winter rye (Secale cereale) stand compared to that above a bare soil at the same height. It is focused on air temperature and humidity. The study is based on long-term measurements (1981-1999) at 0.2 m above ground in the agrometeorological field experiment at Berlin-Dahlem (Humboldt-University of Berlin). The microclimate within a winter rye stand differs significantly from that above a bare soil. Temperature and actual vapour pressure differences between both locations depend on the developmental stage of the plants as well as the time of the day. Their influence is so strong that a detailed analysis of the microclimate makes it necessary to break down the growing time of crop into several developmental periods. So, it was possible to describe and explain the characteristics of the phytoclimate in a relatively detailed and comprehensive manner. Thereby the assessment of potential damages caused by pests and diseases within crop stands becomes more precise. (orig.)

  14. Factors affecting forage stand establishment

    Directory of Open Access Journals (Sweden)

    Sulc R.M.

    1998-01-01

    Full Text Available Significant advances have been made in our knowledge of forage seed physiology, technology, and stand establishment practices; however, stand establishment continues to be one of the most common production problems affecting forage crops in the USA. There is a need for research on stand establishment of forage crops under abiotic and biotic stress. Although the forage seed industry produces and markets seed of high quality, new methods of assessing seed vigor are needed and their use should be expanded in the industry to enable matching seed lot performance to specific environmental conditions where performance can be maximized. Seed treatment and seed coating are used in the forage seed industry, and studies have shown they are of benefit in some environments. There is an increase in no-tillage seeding of forage crops, but improvements in the no-tillage planting equipment are needed to make them better suited to small seeds. Other recent developments in seeding techniques include broadcasting seed with dry granular and fluid fertilizers, which improves the efficiency of the seeding operation.

  15. Reliability criteria for voltage stability

    Energy Technology Data Exchange (ETDEWEB)

    Taylor, Carson W.; Silverstein, Brian L. [Bonneville Power Administration, Portland, OR (United States)

    1994-12-31

    In face of costs pressures, there is need to allocate scare resources more effectively in order to achieve voltage stability. This naturally leads to development of probabilistic criteria and notions of rick management. In this paper it is presented a discussion about criteria for long term voltage stability limited to the case in which the time frames are topically several minutes. (author) 14 refs., 1 fig.

  16. A Voltage Quality Detection Method

    DEFF Research Database (Denmark)

    Chen, Zhe; Wei, Mu

    2008-01-01

    This paper presents a voltage quality detection method based on a phase-locked loop (PLL) technique. The technique can detect the voltage magnitude and phase angle of each individual phase under both normal and fault power system conditions. The proposed method has the potential to evaluate vario...... power quality disturbances, such as interruptions, sags and imbalances. Simulation studies have been performed. The effectiveness of the proposed method has been demonstrated under the simulated typical power disturbances....

  17. Spreading and atomization of droplets on a vibrating surface in a standing pressure field

    Science.gov (United States)

    Deepu, P.; Basu, Saptarshi; Saha, Abhishek; Kumar, Ranganathan

    2012-10-01

    We report the first observation and analytical model of deformation and spreading of droplets on a vibrating surface under the influence of an ultrasonic standing pressure field. The standing wave allows the droplet to spread, and the spreading rate varies inversely with viscosity. In low viscosity droplets, the synergistic effect of radial acoustic force and the transducer surface acceleration also leads to capillary waves. These unstable capillary modes grow to cause ultimate disintegration into daughter droplets. We find that using nanosuspensions, spreading and disintegration can be prevented by suppressing the development of capillary modes and subsequent break-up.

  18. A matter of quantum voltages.

    Science.gov (United States)

    Sellner, Bernhard; Kathmann, Shawn M

    2014-11-14

    Voltages inside matter are relevant to crystallization, materials science, biology, catalysis, and aqueous chemistry. The variation of voltages in matter can be measured by experiment, however, modern supercomputers allow the calculation of accurate quantum voltages with spatial resolutions of bulk systems well beyond what can currently be measured provided a sufficient level of theory is employed. Of particular interest is the Mean Inner Potential (V(o))--the spatial average of these quantum voltages referenced to the vacuum. Here we establish a protocol to reliably evaluate V(o) from quantum calculations. Voltages are very sensitive to the distribution of electrons and provide metrics to understand interactions in condensed phases. In the present study, we find excellent agreement with measurements of V(o) for vitrified water and salt crystals and demonstrate the impact of covalent and ionic bonding as well as intermolecular/atomic interactions. Certain aspects in this regard are highlighted making use of simple model systems/approximations. Furthermore, we predict V(o) as well as the fluctuations of these voltages in aqueous NaCl electrolytes and characterize the changes in their behavior as the resolution increases below the size of atoms.

  19. Transpalpebral eye enucleation in the standing horse

    DEFF Research Database (Denmark)

    Christophersen, Mogens Teken

    Transpalpebral eye enucleation in the standing horse. The Nordic Equine Veterinary Conference, Proceedings, Copenhagen. Denmark. Nov. 2011.......Transpalpebral eye enucleation in the standing horse. The Nordic Equine Veterinary Conference, Proceedings, Copenhagen. Denmark. Nov. 2011....

  20. Electronic Current Transducer (ECT) for high voltage dc lines

    Science.gov (United States)

    Houston, J. M.; Peters, P. H., Jr.; Summerayes, H. R., Jr.; Carlson, G. J.; Itani, A. M.

    1980-02-01

    The development of a bipolar electronic current transducer (ECT) for measuring the current in a high voltage dc (HVDC) power line at line potential is discussed. The design and construction of a free standing ECT for use on a 400 kV line having a nominal line current of 2000 A is described. Line current is measured by a 0.0001 ohm shunt whose voltage output is sampled by a 14 bit digital data link. The high voltage interface between line and ground is traversed by optical fibers which carry digital light signals as far as 300 m to a control room where the digital signal is converted back to an analog representation of the shunt voltage. Two redundant electronic and optical data links are used in the prototype. Power to operate digital and optical electronics and temperature controlling heaters at the line is supplied by a resistively and capacitively graded 10 stage cascade of ferrite core transformers located inside the hollow, SF6 filled, porcelain support insulator. The cascade is driven by a silicon controlled rectifier inverter which supplies about 100 W of power at 30 kHz.