WorldWideScience

Sample records for voltage regulating circuit

  1. Accurate Switched-Voltage voltage averaging circuit

    OpenAIRE

    金光, 一幸; 松本, 寛樹

    2006-01-01

    Abstract ###This paper proposes an accurate Switched-Voltage (SV) voltage averaging circuit. It is presented ###to compensated for NMOS missmatch error at MOS differential type voltage averaging circuit. ###The proposed circuit consists of a voltage averaging and a SV sample/hold (S/H) circuit. It can ###operate using nonoverlapping three phase clocks. Performance of this circuit is verified by PSpice ###simulations.

  2. Voltage Regulators for Photovoltaic Systems

    Science.gov (United States)

    Delombard, R.

    1986-01-01

    Two simple circuits developed to provide voltage regulation for highvoltage (i.e., is greater than 75 volts) and low-voltage (i.e., is less than 36 volts) photovoltaic/battery power systems. Use of these circuits results in voltage regulator small, low-cost, and reliable, with very low power dissipation. Simple oscillator circuit controls photovoltaic-array current to regulate system voltage and control battery charging. Circuit senses battery (and system) voltage and adjusts array current to keep battery voltage from exceeding maximum voltage.

  3. Preparation of Power Distribution System for High Penetration of Renewable Energy Part I. Dynamic Voltage Restorer for Voltage Regulation Pat II. Distribution Circuit Modeling and Validation

    Science.gov (United States)

    Khoshkbar Sadigh, Arash

    other analyses. In this study, ETAP, OpenDSS, and GridLab-D are considered, and PSCMD transfer applications written in MATLAB have been developed for each of these to read the circuit model data provided in the UP spreadsheet. In order to test the developed PSCMD transfer applications, circuit model data of a test circuit and a power distribution circuit from Southern California Edison (SCE) - a utility company - both built in CYME, were exported into the spreadsheet file according to the UP format. Thereafter, circuit model data were imported successfully from the spreadsheet files into above mentioned software using the PSCMD transfer applications developed for each software. After the SCE studied circuit is transferred into OpenDSS software using the proposed UP scheme and developed application, it has been studied to investigate the impacts of large-scale solar energy penetration. The main challenge of solar energy integration into power grid is its intermittency (i.e., discontinuity of output power) nature due to cloud shading of photovoltaic panels which depends on weather conditions. In order to conduct this study, OpenDSS time-series simulation feature, which is required due to intermittency of solar energy, is utilized. In this study, the impacts of intermittency of solar energy penetration, especially high-variability points, on voltage fluctuation and operation of capacitor bank and voltage regulator is provided. In addition, the necessity to interpolate and resample unequally spaced time-series measurement data and convert them to equally spaced time-series data as well as the effect of resampling time-interval on the amount of error is discussed. Two applications are developed in Matlab to do interpolation and resampling as well as to calculate the amount of error for different resampling time-intervals to figure out the suitable resampling time-interval. Furthermore, an approach based on cumulative distribution, regarding the length for lines/cables types

  4. Simple buck/boost voltage regulator

    Science.gov (United States)

    Paulkovich, J.; Rodriguez, G. E.

    1980-01-01

    Circuit corrects low or high supply voltage, produces regulated output voltage. Circuit has fewer components because inductory/transformer combination and pulse-width modulator serve double duty. Regulator handles input voltage variation from as low as one half output voltage to as high as input transistor rating. Solar arrays, fuel cells, and thermionic generators might use this regulator.

  5. Principle and Fault Analysis of Voltage Regulator Circuit%电压调节器电路原理及故障分析

    Institute of Scientific and Technical Information of China (English)

    索明何

    2015-01-01

    Firstly, the paper explores the essential characteristics of voltage regulator through experiments, and then analyzes the circuit principle of the voltage regulator. The paper finally discusses the fault analysis method of voltage regulator circuit through the cases.%本文首先通过实验探究电压调节器的本质特性,然后分析电压调节器电路原理,最后通过案例探究电压调节器电路的故障分析方法.

  6. Frequency-controlled voltage regulator

    Science.gov (United States)

    Mclyman, W. T.

    1980-01-01

    Converting input ac to higher frequency reduce size and weight and makes possible unique kind of regulation. Since conversion frequency is above range of human hearing, supply generated on audible noise. It also exploits highfrequency conversion features to regulate its output voltage in novel way. Circuit is inherently short-circuit proof.

  7. Current regulators for I/SUP 2/L circuits to be operated from low-voltage power supplies

    DEFF Research Database (Denmark)

    Bruun, Erik; Hansen, Ole

    1980-01-01

    A new bandgap current reference is described which can be used to control the injector current of I/SUP 2/L circuits for supply voltages down to about 1 V. For small currents the total injector current is obtained as a mirror of the reference current. For large injector currents the current control...... is performed by a series regulator which compares the injector current of one I/SUP 2/L gate to the reference current. The described reference current can be adjusted to give a variation with temperature of about 60 ppm/°C over the temperature range -10 to +70°C. However, in some applications a nonzero......, but well controlled temperature coefficient is desired. It is shown how a temperature stable ring oscillator with I/SUP 2/L gates can be constructed by tailoring the temperature dependence of the supply current appropriately....

  8. Analysis and simulation of the three-phase AC voltage regulation circuit%三相交流调压电路的分析与仿真

    Institute of Scientific and Technical Information of China (English)

    李衍孜

    2012-01-01

    Based on the analysis of the operation principle and mode of the single-phase AC voltage-regulation circuit, the voltage-regulating rule and effect of three-phase AC voltage-regulation was studied deeply in the paper. The theory of the three-phase star-style AC voltage-regulation circuit was tested in matlab/simulink, the simulation result proved the analysis of the theory of the three-phase AC voltage-regulation circuit was correct.%在分析单相交流调压电路运行原理和工作方式的基础上,深入研究了三相交流调压电路的调压规律和调压效果,并在Matlab/simulink仿真平台上对三相星形无中线交流调压电路的理论部分进行了验证,结果表明:三相交流调压电路的分析是正确的.

  9. Sequential circuit design for radiation hardened multiple voltage integrated circuits

    Science.gov (United States)

    Clark, Lawrence T.; McIver, III, John K.

    2009-11-24

    The present invention includes a radiation hardened sequential circuit, such as a bistable circuit, flip-flop or other suitable design that presents substantial immunity to ionizing radiation while simultaneously maintaining a low operating voltage. In one embodiment, the circuit includes a plurality of logic elements that operate on relatively low voltage, and a master and slave latches each having storage elements that operate on a relatively high voltage.

  10. SEMICONDUCTOR INTEGRATED CIRCUITS: A current-mode voltage regulator with an embedded sub-threshold reference for a passive UHF RFID transponder

    Science.gov (United States)

    Zhongqi, Liu; Chun, Zhang; Yongming, Li; Zhihua, Wang

    2010-06-01

    This paper presents a current-mode voltage regulator for a passive UHF RFID transponder. The passive tag power is extracted from RF energy through the RF-to-DC rectifier. Due to huge variations of the incoming RF power, the rectifier output voltage should be regulated to achieve a stable power supply. By accurately controlling the current flowing into the load with an embedded sub-threshold reference, the regulated voltage varies in a range of 1-1.3 V from -20 to 80 °C, and a bandwidth of about 100 kHz is achieved for a fast power recovery. The circuit is fabricated in UMC 0.18 μm mixed-mode CMOS technology, and the current consumption is only 1 μA.

  11. Low-Voltage Switched-Capacitor Circuits

    DEFF Research Database (Denmark)

    Bidari, E.; Keskin, M.; Maloberti, F.

    1999-01-01

    Switched-capacitor stages are described which can function with very low (typically 1 V) supply voltages, without using voltage boosting or switched op-amps. Simulations indicate that high performance may be achieved using these circuits in filter or data converter applications.......Switched-capacitor stages are described which can function with very low (typically 1 V) supply voltages, without using voltage boosting or switched op-amps. Simulations indicate that high performance may be achieved using these circuits in filter or data converter applications....

  12. SEMICONDUCTOR INTEGRATED CIRCUITS: A full on-chip CMOS low-dropout voltage regulator with VCCS compensation

    Science.gov (United States)

    Leisheng, Gao; Yumei, Zhou; Bin, Wu; Jianhua, Jiang

    2010-08-01

    A full on-chip CMOS low-dropout (LDO) voltage regulator with high PSR is presented. Instead of relying on the zero generated by the load capacitor and its equivalent series resistance, the proposed LDO generates a zero by voltage-controlled current sources for stability. The compensating capacitor for the proposed scheme is only 0.18 pF, which is much smaller than the capacitor of the conventional compensation scheme. The full on-chip LDO was fabricated in commercial 0.35 μm CMOS technology. The active chip area of the LDO (including the bandgap voltage reference) is 400 × 270 μm2. Experimental results show that the PSR of the LDO is -58.7 dB at a frequency of 10 Hz and -20 dB at a frequency of 1 MHz. The proposed LDO is capable of sourcing an output current up to 50 mA.

  13. 内燃机车励磁恒压调节装置电路设计%Circuit design of excitation and constant voltage regulator for diesel locomotive

    Institute of Scientific and Technical Information of China (English)

    邵志和

    2001-01-01

    介绍内燃机车励磁恒压调节装置的功能,详细叙述了该装置的过压、欠压和过流保护电路原理,阐述了利用脉宽调制来控制输出的电压值和电流值的方法。TPZ25型恒压励磁调节装置现已运用在160km/h“曙光号”内燃动车上,在国内内燃机车供电系统属首次研制。%Functions of the excitation and constant voltage regulator fordiesel locomotive are introduced, of which the circuit principle of over-voltage, under-voltage and over-current protection is depicted. Also expounded is the voltage and current control method via pulse width modulation (PWM). Currently TPZ25 excitation and constant voltage regulator has been installed on 160 km/h “Shu Guang Hao” DMU.

  14. VOLTAGE REGULATORS OF SYNCHRONOUS GENERATORS

    Directory of Open Access Journals (Sweden)

    Grigorash O. V.

    2015-06-01

    Full Text Available Synchronous generators are the primary source of electrical power autonomous electrosupply systems, including backup systems. They are also used in a structure of rotating electricity converters and are widely used in renewable energy as part of wind power plants of small, mini and micro hydroelectric plants. Increasing the speed and the accuracy of the system of the voltage regulation of synchronous generators is possible due to the development of combined systems containing more stabilizers. The article illustrates the functional schemes of circuit voltage stabilizers and frequency synchronous generators (with electromagnetic excitation and permanent magnet excitation and describes the features of their work, including two and three-aggregate rotating converters of electricity used in uninterruptible power supply systems. To improve the technical characteristics of the system of stabilization we have proposed functional solutions for stabilizers of synchronous generators made on the base of direct frequency converters and using a transformer with a rotating magnetic field. To improve the reliability of and to improve the operational characteristics of the autonomous independent sources of electricity we suggest creating the main functional blocks and the elements of the stabilization system in a modular way. The functional circuit solutions of voltage regulators of synchronous generators and the characteristics of their work considered in the article, are able to improve the efficiency of pre-design work in the development of new technical solutions for stabilizing the voltage and the frequency in synchronous generators of electrosupply autonomous systems

  15. 30 CFR 77.800 - High-voltage circuits; circuit breakers.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false High-voltage circuits; circuit breakers. 77.800... COAL MINES Surface High-Voltage Distribution § 77.800 High-voltage circuits; circuit breakers. High-voltage circuits supplying power to portable or mobile equipment shall be protected by suitable...

  16. 30 CFR 75.800 - High-voltage circuits; circuit breakers.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false High-voltage circuits; circuit breakers. 75.800... § 75.800 High-voltage circuits; circuit breakers. High-voltage circuits entering the underground area of any coal mine shall be protected by suitable circuit breakers of adequate interrupting...

  17. VOLTAGE REGULATORS ASYNCHRONOUS GENERATORS

    Directory of Open Access Journals (Sweden)

    Grigorash O. V.

    2015-06-01

    Full Text Available A promising is currently the use of asynchronous generators with capacitive excitation as a source of electricity in stand-alone power systems. Drive asynchronous generators may exercise as a thermal engine and wind wheel wind power plant or turbines of small hydropower plants. The article discusses the structural and schematics of voltage stabilizers and frequency of asynchronous generators with improved operational and technical specifications. Technical novelty of design solutions of the magnetic system and stabilizers asynchronous generator of electricity parameters confirmed by the patents for the invention of the Russian Federation. The proposed technical solution voltage stabilizer asynchronous generators, can reduce the weight of the block capacitors excitation and reactive power compensation, as well as to simplify the control system power circuit which has less power electronic devices. For wind power plants it is an important issue not only to stabilize the voltage of the generator, but also the frequency of the current. Recommend functionality stabilizer schemes parameters of electric power made for direct frequency converters with artificial and natural switching power electronic devices. It is also proposed as part of stabilization systems use single-phase voltage, three-phase transformers with rotating magnetic field, reduce the level of electromagnetic interference generated by power electronic devices for switching, enhance the efficiency and reliability of the stabilizer.

  18. Variation-aware adaptive voltage scaling for digital CMOS circuits

    CERN Document Server

    Wirnshofer, Martin

    2013-01-01

    Increasing performance demands in integrated circuits, together with limited energy budgets, force IC designers to find new ways of saving power. One innovative way is the presented adaptive voltage scaling scheme, which tunes the supply voltage according to the present process, voltage and temperature variations as well as aging. The voltage is adapted “on the fly” by means of in-situ delay monitors to exploit unused timing margin, produced by state-of-the-art worst-case designs. This book discusses the design of the enhanced in-situ delay monitors and the implementation of the complete control-loop comprising the monitors, a control-logic and an on-chip voltage regulator. An analytical Markov-based model of the control-loop is derived to analyze its robustness and stability. Variation-Aware Adaptive Voltage Scaling for Digital CMOS Circuits provides an in-depth assessment of the proposed voltage scaling scheme when applied to an arithmetic and an image processing circuit. This book is written for engine...

  19. Kirchhoff voltage law corrected for radiating circuits

    CERN Document Server

    Lara, Vitor

    2014-01-01

    When a circular loop composed by a RLC is put to oscillate, the oscillation will eventually vanish in an exponentially decaying current, even considering superconducting wires, due to the emission of electric and magnetic dipole radiation. In this work we propose a modification on the Kirchhoff voltage law by adding the radiative contributions to the energy loss as an effective resistance, whose value is relatively small when compared to typical resistance value, but fundamental to describe correctly real circuits. We have also analysed the change in the pattern of the radiation spectra emitted by the circuit as we vary both the effective and electrical resistance.

  20. Isolated Fast High-Voltage Switching Circuit

    Science.gov (United States)

    Rizzi, Anthony

    1992-01-01

    Electrically isolated switching circuit supplies pulses at potentials up to 6.5 kV and currents up to 6.5 A, lasting as long as few microseconds. Turn-on time about 40 ns; turn-off time about 3 microseconds. Electrically isolated from control circuitry by means of fiber-optic signal coupling and isolated power supply. Electrical isolation protects both technician and equipment. This and similar circuits useful in such industrial and scientific applications as high-voltage, high-frequency test equipment; electrostatic-discharge test equipment; plasma-laboratory instrumentation; spark chambers; and electromagnetic-interference test equipment.

  1. High voltage generator circuit with low power and high efficiency applied in EEPROM

    Institute of Scientific and Technical Information of China (English)

    Liu Yan; Zhang Shilin; Zhao Yiqiang

    2012-01-01

    This paper presents a low power and high efficiency high voltage generator circuit embedded in electrically erasable programmable read-only memory (EEPROM).The low power is minimized by a capacitance divider circuit and a regulator circuit using the controlling clock switch technique.The high efficiency is dependent on the zero threshold voltage (Vth) MOSFET and the charge transfer switch (CTS) charge pump.The proposed high voltage generator circuit has been implemented in a 0.35μm EEPROM CMOS process.Measured results show that the proposed high voltage generator circuit has a low power consumption of about 150.48 μW and a higher pumping efficiency (83.3%) than previously reported circuits.This high voltage generator circuit can also be widely used in low-power flash devices due to its high efficiency and low power dissipation.

  2. A low voltage CMOS low drop-out voltage regulator

    Science.gov (United States)

    Bakr, Salma Ali; Abbasi, Tanvir Ahmad; Abbasi, Mohammas Suhaib; Aldessouky, Mohamed Samir; Abbasi, Mohammad Usaid

    2009-05-01

    A low voltage implementation of a CMOS Low Drop-Out voltage regulator (LDO) is presented. The requirement of low voltage devices is crucial for portable devices that require extensive computations in a low power environment. The LDO is implemented in 90nm generic CMOS technology. It generates a fixed 0.8V from a 2.5V supply which on discharging goes to 1V. The buffer stage used is unity gain configured unbuffered OpAmp with rail-to-rail swing input stage. The simulation result shows that the implemented circuit provides load regulation of 0.004%/mA and line regulation of -11.09mV/V. The LDO provides full load transient response with a settling time of 5.2μs. Further, the dropout voltage is 200mV and the quiescent current through the pass transistor (Iload=0) is 20μA. The total power consumption of this LDO (excluding bandgap reference) is only 80μW.

  3. Integrated differential high-voltage transmitting circuit for CMUTs

    DEFF Research Database (Denmark)

    Llimos Muntal, Pere; Larsen, Dennis Øland; Farch, Kjartan

    2015-01-01

    In this paper an integrated differential high-voltage transmitting circuit for capacitive micromachined ultrasonic transducers (CMUTs) used in portable ultrasound scanners is designed and implemented in a 0.35 μm high-voltage process. Measurements are performed on the integrated circuit in order...... to assess its performance. The circuit generates pulses at differential voltage levels of 60V, 80V and 100 V, a frequency up to 5MHz and a measured driving strength of 1.75 V/ns with the CMUT connected. The total on-chip area occupied by the transmitting circuit is 0.18 mm2 and the power consumption...

  4. 基于MCU控制的开关电源稳压电路设计%Design for voltage regulator circuit of switching power supply based on MCU control

    Institute of Scientific and Technical Information of China (English)

    李淑红; 邢军

    2015-01-01

    A voltage regulator circuit of the switching power supply based on MCU control was designed,which is com-posed of rectification filtering circuit,push-pull power conversion circuit and control circuit. In this circuit,the output voltage of the switching power supply is controlled by regulating PWM via the MCU. The digital signal output by MCU is converted into analog signal through the DAC0832. The analog signal is taken as the reference voltage of the second pin of the switching con-trol chip SG3525. SG3525 generates PWM control pulse automatically according to the variation of reference voltage to regulate the output pulse width of the switching tube,so the purpose of regulating the output voltage is achieved. The experimental re-sults show that the output voltage adjustable range is 28~36 V,the maximum output current is 15 A,and the efficiency of the switching power supply is 89%.%设计了一款基于MCU控制的开关电源稳压电路,该系统主要由整流滤波电路、推挽式功率变换电路和控制电路组成,并通过MCU调节PWM控制开关电源输出电压.MCU输出的数字信号通过DAC0832转换为模拟信号,该模拟信号作为开关控制芯片SG3525第二管脚的基准电压,SG3525根据基准电压的变化自动产生PWM控制脉冲,调节开关管的输出脉宽,从而达到调节输出电压的目的.实验表明,输出电压可调范围为28~36 V,最大输出电流Imax=15 A,开关电源的效率为η=89%.

  5. Integrated Reconfigurable High-Voltage Transmitting Circuit for CMUTs

    DEFF Research Database (Denmark)

    Llimos Muntal, Pere; Larsen, Dennis Øland; Jørgensen, Ivan Harald Holger

    2014-01-01

    -out and measurements are performed on the integrated circuit. The transmitting circuit is reconfigurable externally making it able to drive a wide variety of CMUTs. The transmitting circuit can generate several pulse shapes, pulse voltages up to 100 V, maximum pulse range of 50 V and frequencies up to 5 MHz. The area...

  6. A High-Voltage Level Tolerant Transistor Circuit

    NARCIS (Netherlands)

    Annema, Anne Johan; Geelen, Godefridus Johannes Gertrudis Maria

    2001-01-01

    A high-voltage level tolerant transistor circuit, comprising a plurality of cascoded transistors, including a first transistor (T1) operatively connected to a high-voltage level node (3) and a second transistor (T2) operatively connected to a low-voltage level node (2). The first transistor (T1) con

  7. The voltage-current relationship and equivalent circuit implementation of parallel flux-controlled memristive circuits

    Institute of Scientific and Technical Information of China (English)

    Bao Bo-Cheng; Feng Fei; Dong Wei; Pan Sai-Hu

    2013-01-01

    A flux-controlled memristor characterized by smooth cubic nonlinearity is taken as an example,upon which the voltage-current relationships (VCRs) between two parallel memristive circuits-a parallel memristor and capacitor circuit (the parallel MC circuit),and a parallel memristor and inductor circuit (the parallel ML circuit)-are investigated.The results indicate that the VCR between these two parallel memristive circuits is closely related to the circuit parameters,and the frequency and amplitude of the sinusoidal voltage stimulus.An equivalent circuit model of the memristor is built,upon which the circuit simulations and experimental measurements of both the parallel MC circuit and the parallel ML circuit are performed,and the results verify the theoretical analysis results.

  8. Voltage Regulator for a dc-to-dc Converter

    Science.gov (United States)

    Mclyman, C. W.

    1983-01-01

    New voltage regulator isolates signals from power-switching converter without use of complex circuitry or optical couplers. Only addition is extra secondary winding on existing interstage transformer. Error signals shortcircuit new winding and inhibit converter action. Resistor in series with primary winding limits short-circuit current to prevent damage to circuit components. Extra transformer winding eliminates need for isolation components.

  9. Inverter-based circuit design techniques for low supply voltages

    CERN Document Server

    Palani, Rakesh Kumar

    2017-01-01

    This book describes intuitive analog design approaches using digital inverters, providing filter architectures and circuit techniques enabling high performance analog circuit design. The authors provide process, supply voltage and temperature (PVT) variation-tolerant design techniques for inverter based circuits. They also discuss various analog design techniques for lower technology nodes and lower power supply, which can be used for designing high performance systems-on-chip.    .

  10. Integrated reconfigurable high-voltage transmitting circuit for CMUTs

    DEFF Research Database (Denmark)

    Llimos Muntal, Pere; Larsen, Dennis Øland; Jørgensen, Ivan Harald Holger

    2015-01-01

    In this paper a high-voltage transmitting circuit aimed for capacitive micromachined ultrasonic transducers (CMUTs) used in scanners for medical applications is designed and implemented in a 0.35 μm high-voltage CMOS process. The transmitting circuit is reconfigurable externally making it able...... performance. The design occupies an on-chip area of 0.938 mm2 and the power consumption of a 128-element transmitting circuit array that would be used in an portable ultrasound scanner is found to be a maximum of 181 mW....

  11. Integrated reconfigurable high-voltage transmitting circuit for CMUTs

    DEFF Research Database (Denmark)

    Llimos Muntal, Pere; Larsen, Dennis Øland; Jørgensen, Ivan Harald Holger;

    2015-01-01

    In this paper a high-voltage transmitting circuit aimed for capacitive micromachined ultrasonic transducers (CMUTs) used in scanners for medical applications is designed and implemented in a 0.35 μm high-voltage CMOS process. The transmitting circuit is reconfigurable externally making it able...... performance. The design occupies an on-chip area of 0.938 mm2 and the power consumption of a 128-element transmitting circuit array that would be used in an portable ultrasound scanner is found to be a maximum of 181 mW....

  12. 30 CFR 75.900 - Low- and medium-voltage circuits serving three-phase alternating current equipment; circuit...

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Low- and medium-voltage circuits serving three... STANDARDS-UNDERGROUND COAL MINES Underground Low- and Medium-Voltage Alternating Current Circuits § 75.900 Low- and medium-voltage circuits serving three-phase alternating current equipment; circuit breakers...

  13. Method for Improve the Design of Diode Voltage Regulator Circuit for Solar Calculator%一种改进太阳能计算器芯片二极管稳压电路设计

    Institute of Scientific and Technical Information of China (English)

    张立荣

    2012-01-01

      For solar energy calculator, the voltage regulator circuit is composed by three PN junction diodes in series. The design may cause some issue:because of the higher Vf for voltage regulator circuit, the voltage of solar energy battery is too higher to arouse voltage can not release in time when sunlight is strong. These issue will lead to calculator can not work well. This paper improve the design of diode voltage regulator circuit. One PN junction diode be changed to shottky diode by change P+mask. So the Vf get more reasonable range than ever. What is more, the impact is researched on thickness of Ti layer and temperature. Finally, it show that this improvement fit our requirement.%  对于太阳能计算器,稳压电路的设计是串联三个PN结二极管以达到稳压目的。这种设计会出现以下问题:当外部光线太强时,太阳能电池板的供电电压较高,而稳压电路由于正向饱和压降过高,不能及时将高电压释放掉,会造成计算器不能正常工作。文章研究了改进二极管稳压电路的设计,通过只变更其中的一层mask(P+),将其中一个PN结二极管改为肖特基二极管,使其正向饱和压降处于一个合理的区间,并且研究了通过该变动后不同的Ti金属厚度以及不同温度对该稳压电路的影响。结果显示该种优化完全符合应用需求。

  14. Noise tolerant voltage-controlled LC oscillator circuits for deep submicron VLSI system-on-a-chip radio circuits

    OpenAIRE

    Typpö, Jukka

    2003-01-01

    This thesis studies the problems with maintaining the spectral purity of fully integrated VCO circuits for radio frequency synthesizers in single-chip system designs. LC tank circuit oscillator circuits are shown to convert amplitude variation in the tank circuit voltage into frequency modulation, if voltage dependent capacitances are present in the tank circuit. Since the parasitic capacitances of the gain transistors and the capacitance of the varactor device in a VCO circuit are voltage de...

  15. 7800系列三端固定集成稳压器应用电路的可靠性设计%Reliability Design of Application Circuit for 7800 Series Three Terminal Positive Voltage Regulator

    Institute of Scientific and Technical Information of China (English)

    2013-01-01

    The article introduced the working principle for 7800 series three terminal posi-tive voltage regulator. At the same time, based on the statistic fault data of three terminal positive voltage regulator, it can be classified for five kind fault characteristics. And com-bining the working principle of 7800 series and energy characteristics of the power supply, the five kind of the fault characteristics were analyzed. Finally, the article presented the methods for reliability design of application circuit for 7800 series three terminal positive voltage regulator. The methods are simple to use and have high reliability, and verified in application.%  简介:本文介绍了7800系列三端固定集成稳压器的工作原理。同时根据已统计的三端固定集成稳压器故障数据,归类于五种故障特征,并结合7800系列的工作原理和电源的能量特征对这五种故障进行了分析。最后给出7800系列三端固定集成稳压器应用电路的可靠性设计的方法。这些方法简单实效,且可靠性强,已得到了实际应用验证。

  16. Low Voltage Analog Circuit Design Based on the Flipped Voltage Follower

    Directory of Open Access Journals (Sweden)

    Neeraj Yadav

    2012-03-01

    Full Text Available The desire for portability of electronics equipment generated a need for low power system in battery products like hearing aids, implantable cardiac pacemakers, cell phones and hand held multimedia terminals. Low voltage analog circuit design differs considerably from those of high voltage analog circuit design. This paper present the basic cell knows as “flipped voltage follower” for low voltage/ low power operation. The detailed classification of basic topologies derived from the FVF cell is presented and there is a low voltage current mirror based on FVF cell has been presented. All the Circuit has been simulated using Hspice tool 0.18µm CMOS Technology. Different quality factors such as frequency response, power consumption are considered. A compression also made between previous current mirror and new designed current mirror. The layout of the current mirror has been also designed using Cadence tool.

  17. Thermally-induced voltage alteration for integrated circuit analysis

    Energy Technology Data Exchange (ETDEWEB)

    Cole, Jr., Edward I. (Albuquerque, NM)

    2000-01-01

    A thermally-induced voltage alteration (TIVA) apparatus and method are disclosed for analyzing an integrated circuit (IC) either from a device side of the IC or through the IC substrate to locate any open-circuit or short-circuit defects therein. The TIVA apparatus uses constant-current biasing of the IC while scanning a focused laser beam over electrical conductors (i.e. a patterned metallization) in the IC to produce localized heating of the conductors. This localized heating produces a thermoelectric potential due to the Seebeck effect in any conductors with open-circuit defects and a resistance change in any conductors with short-circuit defects, both of which alter the power demand by the IC and thereby change the voltage of a source or power supply providing the constant-current biasing. By measuring the change in the supply voltage and the position of the focused and scanned laser beam over time, any open-circuit or short-circuit defects in the IC can be located and imaged. The TIVA apparatus can be formed in part from a scanning optical microscope, and has applications for qualification testing or failure analysis of ICs.

  18. Thermally-induced voltage alteration for integrated circuit analysis

    Energy Technology Data Exchange (ETDEWEB)

    Cole, E.I. Jr.

    2000-06-20

    A thermally-induced voltage alteration (TIVA) apparatus and method are disclosed for analyzing an integrated circuit (IC) either from a device side of the IC or through the IC substrate to locate any open-circuit or short-circuit defects therein. The TIVA apparatus uses constant-current biasing of the IC while scanning a focused laser beam over electrical conductors (i.e. a patterned metallization) in the IC to produce localized heating of the conductors. This localized heating produces a thermoelectric potential due to the Seebeck effect in any conductors with open-circuit defects and a resistance change in any conductors with short-circuit defects, both of which alter the power demand by the IC and thereby change the voltage of a source or power supply providing the constant-current biasing. By measuring the change in the supply voltage and the position of the focused and scanned laser beam over time, any open-circuit or short-circuit defects in the IC can be located and imaged. The TIVA apparatus can be formed in part from a scanning optical microscope, and has applications for qualification testing or failure analysis of ICs.

  19. Adaptive Voltage Management Enabling Energy Efficiency in Nanoscale Integrated Circuits

    Science.gov (United States)

    Shapiro, Alexander E.

    Battery powered devices emphasize energy efficiency in modern sub-22 nm CMOS microprocessors rendering classic power reduction solutions not sufficient. Classical solutions that reduce power consumption in high performance integrated circuits are superseded with novel and enhanced power reduction techniques to enable the greater energy efficiency desired in modern microprocessors and emerging mobile platforms. Dynamic power consumption is reduced by operating over a wide range of supply voltages. This region of operation is enabled by a high speed and power efficient level shifter which translates low voltage digital signals to higher voltages (and vice versa), a key component that enables communication among circuits operating at different voltage levels. Additionally, optimizing the wide supply voltage range of signals propagating across long interconnect enables greater energy savings. A closed-form delay model supporting wide voltage range is developed to enable this capability. The model supports an ultra-wide voltage range from nominal voltages to subthreshold voltages, and a wide range of repeater sizes. To mitigate the drawback of lower operating speed at reduced supply voltages, the high performance exhibited by MOS current mode logic technology is exploited. High performance and energy efficient circuits are enabled by combining this logic style with power efficient near threshold circuits. Many-core systems that operate at high frequencies and process highly parallel workloads benefit from this combination of MCML with NTC. Due to aggressive scaling, static power consumption can in some cases overshadow dynamic power. Techniques to lower leakage power have therefore become an important objective in modern microprocessors. To address this issue, an adaptive power gating technique is proposed. This technique utilizes high levels of granularity to save additional leakage power when a circuit is active as opposed to standard power gating that saves static

  20. 46 CFR 111.12-7 - Voltage regulation and parallel operation.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 4 2010-10-01 2010-10-01 false Voltage regulation and parallel operation. 111.12-7... ELECTRIC SYSTEMS-GENERAL REQUIREMENTS Generator Construction and Circuits § 111.12-7 Voltage regulation and parallel operation. Voltage regulation and parallel operation must meet: (a) For AC systems: sections...

  1. Programmable Low-Voltage Circuit Breaker and Tester

    Science.gov (United States)

    Greenfield, Terry

    2008-01-01

    An instrumentation system that would comprise a remotely controllable and programmable low-voltage circuit breaker plus several electric-circuit-testing subsystems has been conceived, originally for use aboard a spacecraft during all phases of operation from pre-launch testing through launch, ascent, orbit, descent, and landing. The system could also be adapted to similar use aboard aircraft. In comparison with remotely controllable circuit breakers heretofore commercially available, this system would be smaller, less massive, and capable of performing more functions, as needed for aerospace applications.

  2. 30 CFR 75.902-1 - Maximum voltage ground check circuits.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Maximum voltage ground check circuits. 75.902-1... Alternating Current Circuits § 75.902-1 Maximum voltage ground check circuits. The maximum voltage used for such ground check circuits shall not exceed 40 volts....

  3. USING PHOTO-INDUCED OPEN-CIRCUIT VOLTAGE

    African Journals Online (AJOL)

    open-circuit voltage decay, silicon photovoltaic solar cells. ..... cells in series configuration encapsulated on a ceramic base with glass cover and has an effective .... silicon solar cells and should be used parallel to the common performance test ...

  4. 30 CFR 77.901 - Protection of low- and medium-voltage three-phase circuits.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Protection of low- and medium-voltage three... WORK AREAS OF UNDERGROUND COAL MINES Low- and Medium-Voltage Alternating Current Circuits § 77.901 Protection of low- and medium-voltage three-phase circuits. (a) Low- and medium-voltage circuits supplying...

  5. 30 CFR 75.907 - Design of trailing cables for medium-voltage circuits.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Design of trailing cables for medium-voltage... Medium-Voltage Alternating Current Circuits § 75.907 Design of trailing cables for medium-voltage circuits. Trailing cables for medium-voltage circuits shall include grounding conductors, a ground check...

  6. 30 CFR 77.902-1 - Fail safe ground check circuits; maximum voltage.

    Science.gov (United States)

    2010-07-01

    ... voltage. 77.902-1 Section 77.902-1 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF... OF UNDERGROUND COAL MINES Low- and Medium-Voltage Alternating Current Circuits § 77.902-1 Fail safe ground check circuits; maximum voltage. The maximum voltage used for ground check circuits under §...

  7. Design techniques for low-voltage analog integrated circuits

    Science.gov (United States)

    Rakús, Matej; Stopjaková, Viera; Arbet, Daniel

    2017-08-01

    In this paper, a review and analysis of different design techniques for (ultra) low-voltage integrated circuits (IC) are performed. This analysis shows that the most suitable design methods for low-voltage analog IC design in a standard CMOS process include techniques using bulk-driven MOS transistors, dynamic threshold MOS transistors and MOS transistors operating in weak or moderate inversion regions. The main advantage of such techniques is that there is no need for any modification of standard CMOS structure or process. Basic circuit building blocks like differential amplifiers or current mirrors designed using these approaches are able to operate with the power supply voltage of 600 mV (or even lower), which is the key feature towards integrated systems for modern portable applications.

  8. A New Low Voltage P-MOS Bulk Driven Current Mirror Circuit

    Directory of Open Access Journals (Sweden)

    Anuj Dugaya

    2013-08-01

    Full Text Available This work proposes a new low voltage current mirror circuit using bulk driven technique. Bulk driventechnique is used to reduce the threshold of PMOS used in low voltage current mirror circuits (LVCM.TheProposed circuit consist of 4 PMOS and 5 NMOS. The proposed circuit operated at +0.85 V supplyvoltage.The bandwidth of this circuit has also been enhanced using resistive compensation technique. Theproposed circuit has been simulated in Cadence Design Environment in UMC 180nm CMOS technology. Atransfer characteristic of the proposed circuit has been discussed. The proposed circuit find application inlow voltage and low power analog integrated circuits.

  9. Circuit reactivation dynamically regulates synaptic plasticity in neocortex

    Science.gov (United States)

    Kruskal, Peter B.; Li, Lucy; Maclean, Jason N.

    2013-10-01

    Circuit reactivations involve a stereotyped sequence of neuronal firing and have been behaviourally linked to memory consolidation. Here we use multiphoton imaging and patch-clamp recording, and observe sparse and stereotyped circuit reactivations that correspond to UP states within active neurons. To evaluate the effect of the circuit on synaptic plasticity, we trigger a single spike-timing-dependent plasticity (STDP) pairing once per circuit reactivation. The pairings reliably fall within a particular epoch of the circuit sequence and result in long-term potentiation. During reactivation, the amplitude of plasticity significantly correlates with the preceding 20-25 ms of membrane depolarization rather than the depolarization at the time of pairing. This circuit-dependent plasticity provides a natural constraint on synaptic potentiation, regulating the inherent instability of STDP in an assembly phase-sequence model. Subthreshold voltage during endogenous circuit reactivations provides a critical informative context for plasticity and facilitates the stable consolidation of a spatiotemporal sequence.

  10. Silicon solar cells with high open-circuit voltage

    Science.gov (United States)

    Minnucci, J. A.; Matthei, K. W.; Kirkpatrick, A. R.; Mccrosky, A.

    1980-01-01

    Open-circuit voltages as high as 0.645 V (AM0-25 C) have been obtained by a new process developed for low-resistivity silicon. The method utilizes high-dose phosphorus implantation, followed by furnace annealing and simultaneous oxide growth to form high-efficiency, shallow junctions. The effect of the thermally grown oxide is a reduction of surface recombination velocity; the oxide also acts as a moderately efficient AR coating. Boron doped silicon with resistivities from 0.1 to 0.3 ohm-cm has been processed according to this sequence; results show highest open-circuit voltage is attained with 0.1-ohm-cm starting material. The effects of bandgap narrowing, caused by high doping concentrations in the junction, were also investigated by implanting phosphorus over a wide range of dose levels.

  11. Modeling and Verification of Distributed Generation and Voltage Regulation Equipment for Unbalanced Distribution Power Systems; Annual Subcontract Report, June 2007

    Energy Technology Data Exchange (ETDEWEB)

    Davis, M. W.; Broadwater, R.; Hambrick, J.

    2007-07-01

    This report summarizes the development of models for distributed generation and distribution circuit voltage regulation equipment for unbalanced power systems and their verification through actual field measurements.

  12. 30 CFR 75.902 - Low- and medium-voltage ground check monitor circuits.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Low- and medium-voltage ground check monitor... Medium-Voltage Alternating Current Circuits § 75.902 Low- and medium-voltage ground check monitor circuits. On or before September 30, 1970, low- and medium-voltage resistance grounded systems shall...

  13. 30 CFR 77.802 - Protection of high-voltage circuits; neutral grounding resistors; disconnecting devices.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Protection of high-voltage circuits; neutral... AND SURFACE WORK AREAS OF UNDERGROUND COAL MINES Surface High-Voltage Distribution § 77.802 Protection of high-voltage circuits; neutral grounding resistors; disconnecting devices. High-voltage...

  14. 30 CFR 77.803-1 - Fail safe ground check circuits; maximum voltage.

    Science.gov (United States)

    2010-07-01

    ... voltage. 77.803-1 Section 77.803-1 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF... OF UNDERGROUND COAL MINES Surface High-Voltage Distribution § 77.803-1 Fail safe ground check circuits; maximum voltage. The maximum voltage used for ground check circuits under § 77.803 shall...

  15. Novel Low Loss Active Voltage Clamp Circuit for Series Connection of RCGCT thyristors

    Science.gov (United States)

    Ito, Hiroshi; Suzuki, Akihiro; Iwata, Akihiko

    This paper describes novel low loss active voltage clamp circuits for the series connection of RCGCT thyristors. For high voltage converters the series connection of power semiconductor devices is an essential technique for direct switching of high voltages. Several protection circuits have been applied to the series connection of RCGCT thyristors such as CRD snubber circuits which suppress over-voltages across RCGCT thyristors, and voltage balancing resistors to equalize voltage sharing in steady states. However, significant losses in these protection circuits lower the converter’s efficiency. We propose novel low-loss protection circuits, which have active voltage clamp snubber circuits and static voltage balancing circuits. The clamp capacitor voltage of the active voltage clamp snubber circuits are designed to be higher than the equally divided DC-Link voltage. This method can reduce the loss of the clamp circuit to no more than 1/10 of that of the conventional CRD snubber. Also the static voltage balancing circuits compensate for the voltage imbalance generated by the difference in the leakage current between the series connection RCGCT thyristors.

  16. 30 CFR 77.900 - Low- and medium-voltage circuits serving portable or mobile three-phase alternating current...

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Low- and medium-voltage circuits serving... Medium-Voltage Alternating Current Circuits § 77.900 Low- and medium-voltage circuits serving portable or mobile three-phase alternating current equipment; circuit breakers. Low- and medium-voltage circuits...

  17. Deployment of low-voltage regulator considering existing voltage control in medium-voltage distribution systems

    Directory of Open Access Journals (Sweden)

    Hiroshi Kikusato

    2016-01-01

    Full Text Available Many photovoltaic (PV systems have been installed in distribution systems. This installation complicates the maintenance of all voltages within the appropriate range in all low-voltage distribution systems (LVDSs because the trends in voltage fluctuation differ in each LVDS. The installation of a low-voltage regulator (LVR that can accordingly control the voltage in each LVDS has been studied as a solution to this problem. Voltage control in a medium-voltage distribution system must be considered to study the deployment of LVRs. In this study, we installed LVRs in the LVDSs in which the existing voltage-control scheme cannot prevent voltage deviation and performed a numerical simulation by using a distribution system model with PV to evaluate the deployment of the LVRs.

  18. Stabilizing Ferroresonance Oscillations in Voltage Transformers Using Limiter Circuit

    Directory of Open Access Journals (Sweden)

    Hamid Radmanesh

    2012-12-01

    Full Text Available This paper employs the multiple scales method and chaos theory for analyzing chaotic behavior of the voltage transformer (VT with linear core loss model. It is shown that ferroresonance phenomenon in VTs can be classified as chaotic dynamics, including a sequence of bifurcations such as period doubling bifurcation (PDB, saddle node bifurcation (SNB, Hopf Bifurcation (HB and chaos. Bifurcation diagrams and phase plane diagrams are drawn using a continuation method for linear core loss model and lyapunov exponents are obtained using the multiple scales method. At first an overview of the subject in the literature is provided. Then, ferroresonance phenomenon is introduced and its various types in a VT are simulated. Finally the effects of ferroresonance suppression circuit on stabilizing these oscillations are studied. The proposed approach is implemented using MATLAB, and simulation results are presented. The results show connecting the ferroresonance suppression circuit to the system configuration, causes great controlling effect on ferroresonance overvoltage.

  19. 基于电力电子调压电路的直流不停电融冰技术%Study of DC Ice-melting Without Power Cut Technology Based on Power Electronic Voltage-regulating Circuits

    Institute of Scientific and Technical Information of China (English)

    宋洁莹; 周飞; 拜润清; 蔡林海; 荆平

    2014-01-01

    Ice-coating of transmission lines every year in winter seriously affects reliable operation of power grids in China. Present electrical ice-melting methods all require power interruption, which brings negative effects to power grid. To address this issue, principles and feasibility of DC and AC ice-melting without power cut methods are analyzed, a new DC ice-melting without power cut method is proposed, and its circuit structure and capacity requirements are analyzed. At last, a model of the ice-melting device under PSCAD is built and its principles and functions are verified by simulation. The DC ice-melting without power cut device based on power electronic voltage-regulating circuits has high working efficiency and little influence upon regular power supplying.%我国冬季出现的输电线路覆冰的情况严重影响电力系统的可靠运行,现有的电力融冰均需停电进行,对系统影响较大。针对这个问题,分析交、直流不停电融冰的原理及可行性,提出一种新型的不停电直流融冰方法,对其电路结构和所需容量进行分析,并建立不停电融冰装置仿真模型,进行原理和功能验证。基于电力电子调压电路的不停电直流融冰装置具有融冰效率高且不影响线路供电的优点。

  20. Voltage Regulation by Phase Commutation Control Running On FPAA

    Directory of Open Access Journals (Sweden)

    Ckristian. R. Durán-Blanco

    2013-11-01

    Full Text Available In this article we present a control scheme for triggering a SCR-based rectifier circuit. As implementation platform we use a field-programmable-analog-array device (FPAA that allows the development of algorithms for proportional, PID and sliding mode (SMC control techniques. Results show good performance of tested techniques to avoid effects of perturbations over the circuit load, by keeping regulated the output voltage. This suggests the potential use of the proposed technology for applications of reconfigurable hardware in power electronics.

  1. 30 CFR 77.902 - Low- and medium-voltage ground check monitor circuits.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Low- and medium-voltage ground check monitor... OF UNDERGROUND COAL MINES Low- and Medium-Voltage Alternating Current Circuits § 77.902 Low- and medium-voltage ground check monitor circuits. On and after September 30, 1971, three-phase low- and...

  2. 30 CFR 75.511 - Low-, medium-, or high-voltage distribution circuits and equipment; repair.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Low-, medium-, or high-voltage distribution... Electrical Equipment-General § 75.511 Low-, medium-, or high-voltage distribution circuits and equipment; repair. No electrical work shall be performed on low-, medium-, or high-voltage distribution circuits or...

  3. 30 CFR 75.705-10 - Tying into energized high-voltage surface circuits.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Tying into energized high-voltage surface....705-10 Tying into energized high-voltage surface circuits. If the work of forming an additional circuit by tying into an energized high-voltage surface line is performed from the ground, any...

  4. 30 CFR 77.704-10 - Tying into energized high-voltage surface circuits.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Tying into energized high-voltage surface... AREAS OF UNDERGROUND COAL MINES Grounding § 77.704-10 Tying into energized high-voltage surface circuits. If the work of forming an additional circuit by tying into an energized high-voltage surface line...

  5. 30 CFR 75.803-1 - Maximum voltage ground check circuits.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Maximum voltage ground check circuits. 75.803-1 Section 75.803-1 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR COAL MINE... § 75.803-1 Maximum voltage ground check circuits. The maximum voltage used for ground check...

  6. A New Low Voltage P-MOS Bulk Driven Current Mirror Circuit

    Directory of Open Access Journals (Sweden)

    Anuj Dugaya

    2013-08-01

    Full Text Available This work proposes a new low voltage current mirror circuit using bulk driven technique. Bulk driven technique is used to reduce the threshold of PMOS u sed in low voltage current mirror circuits (LVCM.T he Proposed circuit consist of 4 PMOS and 5 NMOS. The proposed circuit operated at +0.85 V supply voltage.The bandwidth of this circuit has also been enhanced using resistive compensation technique. T he proposed circuit has been simulated in Cadence Desi gn Environment in UMC 180nm CMOS technology. A transfer characteristic of the proposed circuit has been discussed. The proposed circuit find applicat ion in low voltage and low power analog integrated circuit s.

  7. Coordinated Voltage Control of Distributed PV Inverters for Voltage Regulation in Low Voltage Distribution Networks

    DEFF Research Database (Denmark)

    Nainar, Karthikeyan; Pokhrel, Basanta Raj; Pillai, Jayakrishnan Radhakrishna

    2017-01-01

    This paper reviews and analyzes the existing voltage control methods of distributed solar PV inverters to improve the voltage regulation and thereby the hosting capacity of a low-voltage distribution network. A novel coordinated voltage control method is proposed based on voltage sensitivity...... analysis, which is simple for computation and requires moderate automation and communication infrastructure. The proposed method is suitable for a hierarchical control structure where a supervisory controller has the provision to adapt the settings of local PV inverter controllers for overall system...

  8. A novel voltage output integrated circuit temperature sensor

    Institute of Scientific and Technical Information of China (English)

    吴晓波; 方志刚; 等

    2002-01-01

    The novel integrated circuit(IC) temperature sensor presented in this paper works similarly as a two-terminal Zener,has breakdown voltage directly proportional to Kelvin temperature at 10mV/℃,with typical error of less tha ±1.0℃ over a temperature range from-50℃to +120℃ .In addition to all the features that conventional IC temperature sensors have,the new device also has very low static power dissipation(0.5mW),low output impedance(less than 1Ω),execllent stability,high reproducibility,and high precision.The sensor's circuit design and layout are discussed in detail.Applications of the sensor include almost and type of temperature sensing over the range of -50℃-+125℃。The low impedance and linear output of the device make interfacing the readout or control circuitry especially easy.Due to the excellent performance and low cost of this sensor.more application of the sensor over wide temperature range are expected.

  9. Optimization of Temperature Coefficient and Noise Analysis of MOSFET- Only Voltage Reference Circuit

    Directory of Open Access Journals (Sweden)

    Arathi.p

    2016-09-01

    Full Text Available The optimization of temperature coefficient and comparison of output noise of two MOSFET only voltage references are introduced. The circuit behavior is analytically described and the performance of the proposed circuits are confirmed through 180nm CMOS technology in virtuoso and the simulation results are presented. Both the circuits can be operated with supply voltage varies from 0.5-1.2V.The output voltage references varied over a temperature range of -25℃ to 50℃.

  10. Study on the instantaneous protection reliability of low voltage circuit breakers

    Institute of Scientific and Technical Information of China (English)

    LU Jian-guo; DU Tai-hang; LUO Yan-yan

    2007-01-01

    This paper outlines the significance of enhancing the instantaneous protection reliability of low voltage circuit breakers and describes their main failure modes. The instantaneous failure mechanism of low voltage circuit breakers was analyzed so that measures to improve instantaneous protection reliability can be determined. Furthermore, the theory of the instantaneous characteristics Calibration device for low voltage circuit breakers and the method of eliminating the non-periodic component of test current are given in detail. Finally, the test results are presented.

  11. Equivalent realisation circuit for a class of non-ideal voltage-controlled memristors

    Directory of Open Access Journals (Sweden)

    Saihu Pan

    2015-12-01

    Full Text Available In this study, an equivalent realisation circuit with off-the-shelf components and devices is proposed, which can be used to equivalently implement a class of non-ideal voltage-controlled memristors. The mathematical models of the equivalent realisation circuit with three function arithmetic circuits are built and their fingerprints are analysed by the pinched hysteresis loops with bipolar periodic voltage stimuli. The numerical simulations are easily verified by experimental measurements, which indicate that when three function arithmetic circuits are linked, the equivalent realisation circuit can realise three non-ideal voltage-controlled memristors with different non-linearities.

  12. Optimal planning of series resistor to control time constant of test circuit for high-voltage AC circuit-breakers

    Directory of Open Access Journals (Sweden)

    Yoon-Ho Kim

    2016-01-01

    Full Text Available The equivalent test circuit that can deliver both short-circuit current and recovery voltage is used to verify the performance of high-voltage circuit breakers. Most of the parameters in this circuit can be obtained by using a simple calculation or a simulation program. The ratings of the circuit breaker include rated short-circuit breaking current, rated short-circuit making current, rated operating sequence of the circuit breaker and rated short-time current. Among these ratings, the short-circuit making capacity of the circuit breaker is expressed in peak value and not in RMS value similar to breaking capacity. A series resistor or super-excitation is used to control the peak value of the short-circuit current in the equivalent test circuit. When using a series resistor, a higher rating of circuit breakers leads to a higher thermal capacity, thereby requiring additional space. Therefore, an effective, optimal design of the series resistor is essential. This paper proposes a method for reducing thermal capacity and selecting the optimal resistance to limit the making current by controlling the DC time constant of the test circuit.

  13. A novel voltage output integrated circuit temperature sensor

    Institute of Scientific and Technical Information of China (English)

    吴晓波; 赵梦恋; 严晓浪; 方志刚

    2002-01-01

    The novel integrated circuit (IC) temperature sensor presented in this paper works similarly as a two-terminal Zener, has breakdown voltage directly proportional to Kelvin temperature at 10 mV/℃, with typical error of less than ±1.0℃ over a temperature range from -50℃ to +125℃. In addition to all the features that conventional IC temperature sensors have, the new device also has very low static power dissipation ( 0.5 mW ) , low output impedance ( less than 1Ω), excellent stability, high reproducibility, and high precision. The sensor's circuit design and layout are discussed in detail. Applications of the sensor include almost any type of temperature sensing over the range of -50℃-+125℃. The low impedance and linear output of the device make interfacing the readout or control circuitry especially easy. Due to the excellent performance and low cost of this sensor, more applications of the sensor over wide temperature range are expected.

  14. High Voltage Dielectrophoretic and Magnetophoretic Hybrid Integrated Circuit / Microfluidic Chip

    Science.gov (United States)

    Issadore, David; Franke, Thomas; Brown, Keith A.; Hunt, Thomas P.; Westervelt, Robert M.

    2010-01-01

    A hybrid integrated circuit (IC) / microfluidic chip is presented that independently and simultaneously traps and moves microscopic objects suspended in fluid using both electric and magnetic fields. This hybrid chip controls the location of dielectric objects, such as living cells and drops of fluid, on a 60 × 61 array of pixels that are 30 × 38 μm2 in size, each of which can be individually addressed with a 50 V peak-to-peak, DC to 10 MHz radio frequency voltage. These high voltage pixels produce electric fields above the chip’s surface with a magnitude , resulting in strong dielectrophoresis (DEP) forces . Underneath the array of DEP pixels there is a magnetic matrix that consists of two perpendicular sets of 60 metal wires running across the chip. Each wire can be sourced with 120 mA to trap and move magnetically susceptible objects using magnetophoresis (MP). The DEP pixel array and magnetic matrix can be used simultaneously to apply forces to microscopic objects, such as living cells or lipid vesicles, that are tagged with magnetic nanoparticles. The capabilities of the hybrid IC / microfluidic chip demonstrated in this paper provide important building blocks for a platform for biological and chemical applications. PMID:20625468

  15. A novel high voltage start up circuit for an integrated switched mode power supply

    Energy Technology Data Exchange (ETDEWEB)

    Hu Hao; Chen Xingbi, E-mail: huhao21@uestc.edu.c [State Key Laboratory of Electronic Thin Films and Integrated Devices, University of Electronic Science and Technology of China, Chengdu 610054 (China)

    2010-09-15

    A novel high voltage start up circuit for providing an initial bias voltage to an integrated switched mode power supply (SMPS) is presented. An enhanced mode VDMOS transistor, the gate of which is biased by a floating p-island, is used to provide start up current and sustain high voltage. An NMOS transistor having a high source to ground breakdown voltage is included to extend the bias voltage range to the SMPS. Simulation results indicate that the high voltage start up circuit can start and restart as designed. The proposed structure is believed to be more energy saving and cost-effective compared with other solutions. (semiconductor devices)

  16. SEMICONDUCTOR DEVICES: A novel high voltage start up circuit for an integrated switched mode power supply

    Science.gov (United States)

    Hao, Hu; Xingbi, Chen

    2010-09-01

    A novel high voltage start up circuit for providing an initial bias voltage to an integrated switched mode power supply (SMPS) is presented. An enhanced mode VDMOS transistor, the gate of which is biased by a floating p-island, is used to provide start up current and sustain high voltage. An NMOS transistor having a high source to ground breakdown voltage is included to extend the bias voltage range to the SMPS. Simulation results indicate that the high voltage start up circuit can start and restart as designed. The proposed structure is believed to be more energy saving and cost-effective compared with other solutions.

  17. Modeling self-priming circuits for dielectric elastomer generators towards optimum voltage boost

    Science.gov (United States)

    Zanini, Plinio; Rossiter, Jonathan; Homer, Martin

    2016-04-01

    One of the main challenges for the practical implementation of dielectric elastomer generators (DEGs) is supplying high voltages. To address this issue, systems using self-priming circuits (SPCs) — which exploit the DEG voltage swing to increase its supplied voltage — have been used with success. A self-priming circuit consists of a charge pump implemented in parallel with the DEG circuit. At each energy harvesting cycle, the DEG receives a low voltage input and, through an almost constant charge cycle, generates a high voltage output. SPCs receive the high voltage output at the end of the energy harvesting cycle and supply it back as input for the following cycle, using the DEG as a voltage multiplier element. Although rules for designing self-priming circuits for dielectric elastomer generators exist, they have been obtained from intuitive observation of simulation results and lack a solid theoretical foundation. Here we report the development of a mathematical model to predict voltage boost using self-priming circuits. The voltage on the DEG attached to the SPC is described as a function of its initial conditions, circuit parameters/layout, and the DEG capacitance. Our mathematical model has been validated on an existing DEG implementation from the literature, and successfully predicts the voltage boost for each cycle. Furthermore, it allows us to understand the conditions for the boost to exist, and obtain the design rules that maximize the voltage boost.

  18. Regulation of a lightweight high efficiency capacitator diode voltage multiplier dc-dc converter

    Science.gov (United States)

    Harrigill, W. T., Jr.; Myers, I. T.

    1976-01-01

    A method for the regulation of a capacitor diode voltage multiplier dc-dc converter has been developed which has only minor penalties in weight and efficiency. An auxiliary inductor is used, which only handles a fraction of the total power, to control the output voltage through a pulse width modulation method in a buck boost circuit.

  19. Regulation of a lightweight high efficiency capacitor diode voltage multiplier dc-dc converter

    Science.gov (United States)

    Harrigill, W. T., Jr.; Myers, I. T.

    1976-01-01

    A method for the regulation of a capacitor diode voltage multiplier dc-dc converter has been developed which has only minor penalties in weight and efficiency. An auxiliary inductor is used, which only handles a fraction of the total power, to control the output voltage through a pulse width modulation method in a buck boost circuit.

  20. High-Mixed-Voltage Analog and RF Circuit Techniques for Nanoscale CMOS

    CERN Document Server

    Mak, Pui-In

    2012-01-01

    This book presents high-/mixed-voltage analog and radio frequency (RF) circuit techniques for developing low-cost multistandard wireless receivers in nm-length CMOS processes.  Key benefits of high-/mixed-voltage RF and analog CMOS circuits are explained, state-of-the-art examples are studied, and circuit solutions before and after voltage-conscious design are compared. Three real design examples are included, which demonstrate the feasibility of high-/mixed-voltage circuit techniques.    Provides a valuable summary and real case studies of the state-of-the-art in high-/mixed-voltage circuits and systems; Includes novel high-/mixed-voltage analog and RF circuit techniques – from concept to practice; Describes the first high-voltage-enabled mobile-TVRF front-end in 90nm CMOS and the first mixed-voltage full-band mobile-TV Receiver in 65nm CMOS; Demonstrates the feasibility of high-/mixed-voltage circuit techniques with real design examples.  

  1. High voltage dc-dc converter with dynamic voltage regulation and decoupling during load-generated arcs

    Science.gov (United States)

    Shimer, Daniel W.; Lange, Arnold C.

    1995-01-01

    A high-power power supply produces a controllable, constant high voltage output under varying and arcing loads. The power supply includes a voltage regulator, an inductor, an inverter for producing a high frequency square wave current of alternating polarity, an improved inverter voltage clamping circuit, a step up transformer, an output rectifier for producing a dc voltage at the output of each module, and a current sensor for sensing output current. The power supply also provides dynamic response to varying loads by controlling the voltage regulator duty cycle and circuitry is provided for sensing incipient arc currents at the output of the power supply to simultaneously decouple the power supply circuitry from the arcing load. The power supply includes a plurality of discrete switching type dc--dc converter modules.

  2. Voltage regulation of connexin channel conductance.

    Science.gov (United States)

    Oh, Seunghoon; Bargiello, Thaddeus A

    2015-01-01

    Voltage is an important parameter that regulates the conductance of both intercellular and plasma membrane channels (undocked hemichannels) formed by the 21 members of the mammalian connexin gene family. Connexin channels display two forms of voltage-dependence, rectification of ionic currents and voltage-dependent gating. Ionic rectification results either from asymmetries in the distribution of fixed charges due to heterotypic pairing of different hemichannels, or by channel block, arising from differences in the concentrations of divalent cations on opposite sides of the junctional plaque. This rectification likely underpins the electrical rectification observed in some electrical synapses. Both intercellular and undocked hemichannels also display two distinct forms of voltage-dependent gating, termed Vj (fast)-gating and loop (slow)-gating. This review summarizes our current understanding of the molecular determinants and mechanisms underlying these conformational changes derived from experimental, molecular-genetic, structural, and computational approaches.

  3. Analysis of Possibilities to Reduce the Voltages Induced in Multi-circuit and Multi-voltage Overhead Lines

    Directory of Open Access Journals (Sweden)

    Rafał Tarko

    2015-09-01

    Full Text Available This paper presents the issues of electromagnetic interactions in a four-circuit and dual-voltage power line. Such solutions are increasingly used in practice due to difficulties in land acquisition for the construction of new power lines. Lines of this type, however, have some disadvantages, incl. the electromagnetic interactions between the circuits and voltages induced as their consequence. These issues are considered in relation to an existing four-circuit, 110 kV and 15 kV line. Results of the studies of the interaction effects in a real system, and an analysis of selected ways to reduce the voltage induced in 15 kV line circuits are presented.

  4. A Simple Voltage Controlled Oscillator Using Bootstrap Circuits and NOR-RS Flip Flop

    Science.gov (United States)

    Chaikla, Amphawan; Pongswatd, Sawai; Sasaki, Hirofumi; Fujimoto, Kuniaki; Yahara, Mitsutoshi

    This paper presents a simple and successful design for a voltage controlled oscillator. The proposed circuit is based on the use of two identical bootstrap circuits and a NOR-RS Flip Flop to generate wide-tunable sawtooth and square waves. Increasing control voltage linearly increases the output oscillation frequency. Experimental results verifying the performances of the proposed circuit are in agreement with the calculated values.

  5. Open circuit voltage characterization of lithium-ion batteries

    Science.gov (United States)

    Pattipati, B.; Balasingam, B.; Avvari, G. V.; Pattipati, K. R.; Bar-Shalom, Y.

    2014-12-01

    Several aspects of the open circuit voltage (OCV) characterization of Li-ion batteries as it applies to battery fuel gauging (BFG) in portable applications are considered in this paper. Accurate knowledge of the nonlinear relationship between the OCV and the state of charge (SOC) is required for adaptive SOC tracking during battery usage. BFG in portable applications requires this OCV-SOC characterization to meet additional constraints: (i) The OCV-SOC characterization has to be defined with a minimum number of parameters; (ii) It should be easily computable and invertible with few operations; and (iii) Computation of the model, its derivative and its inverse should be possible in a numerically stable way. With the help of OCV-SOC characterization data collected from 34 battery cells each at 16 different temperatures ranging from -25 °C to 50 °C, we present the following results in this paper: (a) A robust normalized OCV modeling approach that dramatically reduces the number of OCV-SOC parameters and as a result simplifies and generalizes the BFG across temperatures and aging, (b) Several novel functions for OCV modeling, (c) Efficient methods to simplify the computations of OCV functions, (d) Novel methods for OCV parameter estimation, and (e) A detailed performance analysis.

  6. A novel on-chip high to low voltage power conversion circuit

    Institute of Scientific and Technical Information of China (English)

    Wang Hui; Wang Songlin; Lai Xinquan; Ye Qiang; Mou Zaixin; Li Xianrui; Guo Baolong

    2009-01-01

    A novel power supply transform technique for high voltage IC based on the TSMC 0.6μm BCD process is achieved. An adjustable bandgap voltage reference is presented which is different from the traditional power supply transform technique. It can be used as an internal power supply for high voltage IC by using the push-pull output stage to enhance its load capability. High-order temperature compensated circuit is designed to ensure the precision of the reference. Only 0.01 mm2 area is occupied using this novel power supply technique. Compared with traditional technique, 50% of the area is saved, 40% quiescent power loss is decreased, and the temperature coefficient of the reference is only 4.48 ppm/℃. Compared with the traditional LDO (low dropout) regulator, this power conversion architecture does not need external output capacitance and decreases the chip-pin and external components, so the PCB area and design cost are also decreased. The testing results show that this circuit works well.

  7. Small-signal, continuous, exact model of PWM voltage regulators

    Science.gov (United States)

    Burkhardt, W.; Maranesi, P.; Varoli, V.

    1985-02-01

    The small-signal time-continuous open-loop response of buck, boost, and buck-boost pulse-width-modulation (PWM) voltage regulators using MOSFET switches in their power stages is modeled, applying a time-domain sampling theorem (Woodward, 1953) to obtain the Fourier open-loop transfer function corresponding to the comb function describing the response at the chopping instants only. The results are presented graphically along with simplified circuit diagrams of the PWM devices, and the accuracy and computational efficiency of the analytical approach are indicated.

  8. Low Power, Reduced Dynamic Voltage Swing Domino Logic Circuits

    OpenAIRE

    Salendra.Govindarajulu; Dr.T.Jayachandra Prasad; Rangappa, P

    2010-01-01

    Dynamic domino logic circuits are widely used in modern digital VLSI circuits. These dynamic circuits are often favoured in high performance designs because of the speed advantage offered over static CMOS logic circuits. The main drawbacks of dynamic logic are a lack of design automation, a decreased tolerance to noise and increased power dissipation. In this work, new reduced – swing domino logic techniques which provide significant low power dissipation as compared to traditional domino cir...

  9. Near-Threshold Computing and Minimum Supply Voltage of Single-Rail MCML Circuits

    Directory of Open Access Journals (Sweden)

    Ruiping Cao

    2014-01-01

    Full Text Available In high-speed applications, MOS current mode logic (MCML is a good alternative. Scaling down supply voltage of the MCML circuits can achieve low power-delay product (PDP. However, the current almost all MCML circuits are realized with dual-rail scheme, where the NMOS configuration in series limits the minimum supply voltage. In this paper, single-rail MCML (SRMCML circuits are described, which can avoid the devices configuration in series, since their logic evaluation block can be realized by only using MOS devices in parallel. The relationship between the minimum supply voltage of the SRMCML circuits and the model parameters of MOS transistors is derived, so that the minimum supply voltage can be estimated before circuit designs. An MCML dynamic flop-flop based on SRMCML is also proposed. The optimization algorithm for near-threshold sequential circuits is presented. A near-threshold SRMCML mode-10 counter based on the optimization algorithm is verified. Scaling down the supply voltage of the SRMCML circuits is also investigated. The power dissipation, delay, and power-delay products of these circuits are carried out. The results show that the near-threshold SRMCML circuits can obtain low delay and small power-delay product.

  10. A Comparative Study of Ultra-Low Voltage Digital Circuit Design

    Directory of Open Access Journals (Sweden)

    Aaron Arthurs

    2012-07-01

    Full Text Available Ultra-low voltage digital circuit design is an active research area, especially for portable applications such as wearable electronics, intelligent remote sensors, implantable medical devices, and energy-harvesting systems. Due to their application scenarios and circuit components, two major goals for these systems are minimizing energy consumption and improving compatibility with low-voltage power supplies and analog components. The most effective solution to achieve these goals is to reduce the supply voltage, which,however, raises the issue of operability. At ultra-low supply voltages, the integrity of digital signals degrades dramatically due to the indifference between active and leakage currents. In addition, the system timing becomes more unpredictable as the impact of process and supply voltage variations being more significant at lower voltages. This paper presents a comparative study among three techniques for designing digital circuits operating at ultra-low voltages, i.e., Schmitt-triggered gate structure, delayinsensitive asynchronous logic, and Fully-Depleted Silicon-on-Insulator technology. Results show that despite the tradeoffs, all eight combinations of these techniques are viable for designing ultra-low voltage circuits. For a given application, the optimum circuit design can be selected from these combinations based on the lowest voltage, the dynamic range, the power budget, the performance requirement, and the available semiconductor process node.

  11. A Comparative Study of Ultra-Low Voltage Digital Circuit Design

    Directory of Open Access Journals (Sweden)

    Aaron Arthurs,

    2012-06-01

    Full Text Available Ultra-low voltage digital circuit design is an active research area, especially for portable applications such as wearable electronics, intelligent remote sensors, implantable medical devices, and energy-harvesting systems. Due to their application scenarios and circuit components, two major goals for these systems are minimizing energy consumption and improving compatibility with low-voltage power supplies and analog components. The most effective solution to achieve these goals is to reduce the supply voltage, which,however, raises the issue of operability. At ultra-low supply voltages, the integrity of digital signals degrades dramatically due to the indifference between active and leakage currents. In addition, the system timing becomes more unpredictable as the impact of process and supply voltage variations being more significant at lower voltages. This paper presents a comparative study among three techniques for designing digital circuits operating at ultra-low voltages, i.e., Schmitt-triggered gate structure, delay insensitive asynchronous logic, and Fully-Depleted Silicon-on-Insulator technology. Results show that despite the trade offs, all eight combinations of these techniques are viable for designing ultra-low voltage circuits. For a given application, the optimum circuit design can be selected from these combinations based on the lowest voltage, the dynamic range, the power budget, the performance requirement, and the available semiconductor process node.

  12. CFD Simulation of Transonic Flow in High-Voltage Circuit Breaker

    Directory of Open Access Journals (Sweden)

    Xiangyang Ye

    2012-01-01

    Full Text Available A high-voltage circuit breaker is an indispensable piece of equipment in the electric transmission and distribution systems. Transonic flow typically occurs inside breaking chamber during the current interruption, which determines the insulating characteristics of gas. Therefore, accurate compressible flow simulations are required to improve the prediction of the breakdown voltages in various test duties of high-voltage circuit breakers. In this work, investigation of the impact of the solvers on the prediction capability of the breakdown voltages in capacitive switching is presented. For this purpose, a number of compressible nozzle flow validation cases have been presented. The investigation is then further extended for a real high-voltage circuit breaker geometry. The correlation between the flow prediction accuracy and the breakdown voltage prediction capability is identified.

  13. Circuit Regulates Speed Of dc Motor

    Science.gov (United States)

    Weaver, Charles; Padden, Robin; Brown, Floyd A., Jr.

    1990-01-01

    Driving circuit regulates speed of small dc permanent-magnet motor in tape recorder. Two nested feedback loops maintain speed within 1 percent of constant value. Inner loop provides coarse regulation, while outer loop removes most of variation in speed that remains in the presence of regulation by the inner loop. Compares speed of motor with commanded speed and adjusts current supplied to motor accordingly.

  14. 30 CFR 75.901 - Protection of low- and medium-voltage three-phase circuits used underground.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Protection of low- and medium-voltage three... Underground Low- and Medium-Voltage Alternating Current Circuits § 75.901 Protection of low- and medium-voltage three-phase circuits used underground. (a) Low- and medium-voltage three-phase alternating-current...

  15. Note: Complementary metal-oxide-semiconductor high voltage pulse generation circuits.

    Science.gov (United States)

    Sun, Jiwei; Wang, Pingshan

    2013-10-01

    We present two types of on-chip pulse generation circuits. The first is based on CMOS pulse-forming-lines (PFLs). It includes a four-stage charge pump, a four-stacked-MOSFET switch and a 5 mm long PFL. The circuit is implemented in a 0.13 μm CMOS process. Pulses of ~1.8 V amplitude with ~135 ps duration on a 50 Ω load are obtained. The obtained voltage is higher than 1.6 V, the rated operating voltage of the process. The second is a high-voltage Marx generator which also uses stacked MOSFETs as high voltage switches. The output voltage is 11.68 V, which is higher than the highest breakdown voltage (~10 V) of the CMOS process. These results significantly extend high-voltage pulse generation capabilities of CMOS technologies.

  16. High-voltage integrated transmitting circuit with differential driving for CMUTs

    DEFF Research Database (Denmark)

    Llimos Muntal, Pere; Larsen, Dennis Øland; Færch, Kjartan Ullitz

    2016-01-01

    In this paper, a high-voltage integrated differential transmitting circuit for capacitive micromachined ultrasonic transducers (CMUTs) used in portable ultrasound scanners is presented. Due to its application, area and power consumption are critical and need to be minimized. The circuitry...... is designed and implemented in AMS 0.35 μ m high-voltage process. Measurements are performed on the fabricated integrated circuit in order to assess its performance. The transmitting circuit consists of a low-voltage control logic, pulse-triggered level shifters and a differential output stage that generates...... pulses at differential voltage levels of 60, 80 and 100 V, a frequency up to 5 MHz and a measured driving strength of 2.03 V/ns with the CMUT electrical model connected. The total on-chip area occupied by the transmitting circuit is 0.18 mm2 and the power consumption at the ultrasound scanner operation...

  17. Implementation of a Capacitor Less Low Dropout Voltage Regulator on Chip (SOC

    Directory of Open Access Journals (Sweden)

    Shailika Sharma

    2014-06-01

    Full Text Available — In this paper we have implemented a linear voltage low drop out regulator for efficient power management considering the fact in mind that voltage regulators provide a constant voltage supply to the circuits. We replace the common drain by common source pass element to improve efficiency and reduce the voltage drop across the device. This research paper includes the process to remove the external capacitor allowing for greater power system (soc application. A compensation scheme is presented that provides both a fast transient response and full range alternating current (ac stability from 0 to 50 mA load current even if the output load is as high as 100 pf. A 2.7-v capacitorless LDO voltage regulator with a power supply 3 v was designed with a dropout voltage of 300 mv.

  18. Low-Voltage Process-Compensated VCO with On-Chip Process Monitoring and Body-Biasing Circuit Techniques

    OpenAIRE

    Ueno, Ken; Hirose, Tetsuya; Asai, Tetsuya; Amemiya, Yoshihito

    2009-01-01

    A voltage-controlled oscillator (VCO) tolerant to process variations at lower supply voltage was proposed. The circuit consists of an on-chip threshold-voltage-monitoring circuit, a current-source circuit, a body-biasing control circuit, and the delay cells of the VCO. Because variations in low-voltage VCO frequency are mainly determined by that of the current in delay cells. a current-compensation technique was adopted by using an on-chip threshold-voltage-monitoring circuit and body-biasing...

  19. Optimal condition of memristance enhancement circuit using external voltage source

    Directory of Open Access Journals (Sweden)

    Hiroya Tanaka

    2014-05-01

    Full Text Available Memristor provides nonlinear response in the current-voltage characteristic and the memristance is modulated using an external voltage source. We point out by solving nonlinear equations that an optimal condition of the external voltage source exists for maximizing the memristance in such modulation scheme. We introduce a linear function to describe the nonlinear time response and derive an important design guideline; a constant ratio of the frequency to the amplitude of the external voltage source maximizes the memristance. The analysis completely accounts for the memristance behavior.

  20. A SURVEY: PID OPTIMIZATION FOR AUTOMATIC VOLTAGE REGULATOR

    OpenAIRE

    Ajay Dixit*, Miss.Pragati Joshi, Mr.Mahesh Lokhande

    2016-01-01

    This paper presents on survey paper  of PSO and automatic voltage regulator for synchronous generator. It is used to obtain for regulation and stability of any electrical equipment. There are many technology/methods were used in automatic voltage regulator as well as different controller used for improving robustness, overshoot, rise time and voltage control but problem is about to survey on Automatic Voltage Regulator. Comparisons studies which are based on PID Controller are performed to sh...

  1. A Voltage Doubler Circuit to Extend the Soft-switching Range of Dual Active Bridge Converters

    DEFF Research Database (Denmark)

    Qin, Zian; Shen, Yanfeng; Wang, Huai;

    2017-01-01

    A voltage doubler circuit is realized to extend the soft-switching range of Dual Active Bridge (DAB) converters. No extra hardware is added to the DAB to form this circuit, since it is composed of the dc blocking capacitor and the low side full bridge converter, which already exist in DAB. With t...

  2. 30 CFR 75.802 - Protection of high-voltage circuits extending underground.

    Science.gov (United States)

    2010-07-01

    ... underground. 75.802 Section 75.802 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR COAL MINE SAFETY AND HEALTH MANDATORY SAFETY STANDARDS-UNDERGROUND COAL MINES Underground High-Voltage Distribution § 75.802 Protection of high-voltage circuits extending underground. (a) Except as...

  3. Series-connected substrate-integrated lead-carbon hybrid ultracapacitors with voltage-management circuit

    Indian Academy of Sciences (India)

    A Banerjee; R Srinivasan; A K Shukla

    2015-02-01

    Cell voltage for a fully charged-substrate-integrated lead-carbon hybrid ultracapacitor is about 2.3 V. Therefore, for applications requiring higher DC voltage, several of these ultracapacitors need to be connected in series. However, voltage distribution across each series-connected ultracapacitor tends to be uneven due to tolerance in capacitance and parasitic parallel-resistance values. Accordingly, voltage-management circuit is required to protect constituent ultracapacitors from exceeding their rated voltage. In this study, the design and characterization of the substrate-integrated lead-carbon hybrid ultracapacitor with co-located terminals is discussed. Voltage-management circuit for the ultracapacitor is presented, and its effectiveness is validated experimentally.

  4. Interface circuit with adjustable bias voltage enabling maximum power point tracking of capacitive energy harvesting devices

    Science.gov (United States)

    Wei, J.; Lefeuvre, E.; Mathias, H.; Costa, F.

    2016-12-01

    The operation analysis of a new interface circuit for electrostatic vibration energy harvesting with adjustable bias voltage is carried out in this paper. Two configurations determined by the open or closed states of an electronic switch are examined. The increase of the voltage across a biasing capacitor, occurring when the switch is open, is proved theoretically and experimentally. With the decrease of this biasing voltage which occurs naturally when the switch is closed due to imperfections of the circuit, the bias voltage can be maintained close to a target value by appropriate ON and OFF control of the switch. As the energy converted by the variable capacitor on each cycle depends on the bias voltage, this energy can be therefore accurately controlled. This feature opens up promising perspectives for optimization the power harvested by electrostatic devices. Simulation results with and without electromechanical coupling effect are presented. In experimental tests, a simple switch control enabling to stabilize the bias voltage is described.

  5. Voltage-Mode All-Pass Filters Including Minimum Component Count Circuits

    Directory of Open Access Journals (Sweden)

    Sudhanshu Maheshwari

    2007-01-01

    Full Text Available This paper presents two new first-order voltage-mode all-pass filters using a single-current differencing buffered amplifier and four passive components. Each circuit is compatible to a current-controlled current differencing buffered amplifier with only two passive elements, thus resulting in two more circuits, which employ a capacitor, a resistor, and an active element, thus using a minimum of active and passive component counts. The proposed circuits possess low output impedance, and hence can be easily cascaded for voltage-mode systems. PSPICE simulation results are given to confirm the theory.

  6. A New Transformerless Single-Phase Buck-Boost AC Voltage Regulator

    Directory of Open Access Journals (Sweden)

    YALCIN, F.

    2016-05-01

    Full Text Available Voltage regulation is one of the important goals for electrical sources and consumers. In this paper a new transformerless single-phase AC voltage regulator based on buck-boost converter topology is presented. The regulator circuit has a simple structure using only two bidirectional active switches, one inductor and one capacitor. A closed loop control system is implemented for the proposed regulator operation. A control law depending on the instantaneous values of the regulator's real input and desired output voltage is obtained and supports the PI controller. The control law allows the controller to obtain efficient pulse width modulation (PWM switching duty ratio for the desired output voltage when the input voltage has surges or fluctuations and the output load is changed. An experimental laboratory setup has been implemented for the proposed AC voltage regulator. The obtained results demonstrate that the proposed topology is capable of and efficient for both bucking and boosting the input AC voltage to a high quality output voltage with a low total harmonic distortion (THD for different input voltage and load conditions.

  7. Analysis and calculation of lightning-induced voltages in aircraft electrical circuits

    Science.gov (United States)

    Plumer, J. A.

    1974-01-01

    Techniques to calculate the transfer functions relating lightning-induced voltages in aircraft electrical circuits to aircraft physical characteristics and lightning current parameters are discussed. The analytical work was carried out concurrently with an experimental program of measurements of lightning-induced voltages in the electrical circuits of an F89-J aircraft. A computer program, ETCAL, developed earlier to calculate resistive and inductive transfer functions is refined to account for skin effect, providing results more valid over a wider range of lightning waveshapes than formerly possible. A computer program, WING, is derived to calculate the resistive and inductive transfer functions between a basic aircraft wing and a circuit conductor inside it. Good agreement is obtained between transfer inductances calculated by WING and those reduced from measured data by ETCAL. This computer program shows promise of expansion to permit eventual calculation of potential lightning-induced voltages in electrical circuits of complete aircraft in the design stage.

  8. Short-circuit protection of LLC resonant converter using voltages across resonant tank elements

    Directory of Open Access Journals (Sweden)

    Denys Igorovych Zaikin

    2015-06-01

    Full Text Available This paper describes two methods for the short-circuit protection of the LLC resonant converter. One of them uses the voltage across the capacitor and the other uses the voltage across the inductor of the resonant tank. These voltages can be processed (integrated or differentiated to recover the resonant tank current. The two circuits illustrated in the described methods make it possible to develop a robust LLC converter design and to avoid using lossy current measurement elements, such as a shunt resistor or current transformer. The methods also allow measuring resonant tank current without breaking high-current paths and connecting the measuring circuit in parallel with the inductor or capacitor of the resonant tank. Practical implementations of these indirect current measurements have been experimentally tested for the short-circuit protection of the 1600 W LLC converter.

  9. High-voltage integrated transmitting circuit with differential driving for CMUTs

    DEFF Research Database (Denmark)

    Llimos Muntal, Pere; Larsen, Dennis Øland; Færch, Kjartan Ullitz;

    2016-01-01

    In this paper, a high-voltage integrated differential transmitting circuit for capacitive micromachined ultrasonic transducers (CMUTs) used in portable ultrasound scanners is presented. Due to its application, area and power consumption are critical and need to be minimized. The circuitry...... is designed and implemented in AMS 0.35 μ m high-voltage process. Measurements are performed on the fabricated integrated circuit in order to assess its performance. The transmitting circuit consists of a low-voltage control logic, pulse-triggered level shifters and a differential output stage that generates...... conditions is 0.936 mW including the load. The integrated circuits measured prove to be consistent and robust to local process variations by measurements....

  10. Maximum Output Power Control Using Short-Circuit Current and Open-Circuit Voltage of a Solar Panel

    Science.gov (United States)

    Kato, Takahiro; Miyake, Takuma; Tashima, Daisuke; Sakoda, Tatsuya; Otsubo, Masahisa; Hombu, Mitsuyuki

    2012-10-01

    A control method to optimize the output power of a solar cell is necessary because the output of a solar cell strongly depends on solar radiation. We here proposed two output power control methods using the short-circuit current and open-circuit voltage of a solar panel. One of them used a current ratio and a voltage ratio (αβ control), and the other used a current ratio and a short-circuit current-electric power characteristic coefficient (αγ control). The usefulness of the αβ and the αγ control methods was evaluated. The results showed that the output power controlled by our proposed methods was close to the maximum output power of a solar panel.

  11. Design and Implementation of Voltage-Mode MIN/MAX Circuits

    Directory of Open Access Journals (Sweden)

    M. Soleimani

    2015-12-01

    Full Text Available In this paper, a general architecture for analog implementation of MIN/MAX and other rank order circuits is presented. Based on general architecture, proposed MIN/MAX circuits are implemented. The proposed circuits are composed of a differential amplifier with merged n-inputs and a MCSAL circuit to choose the desired input. The advantages of the proposed structure are simplicity, very high resolution, very low supply voltage requirements, very low output resistor, low power dissipation, low active area and simple expansion for multiple inputs by adding only three transistors for each extra input. The post-layout simulation results of proposed circuits are presented by HSPICE software in 0.35-µm CMOS process technology. The total power dissipation of proposed circuits is about 110-µW. Also, the total active area is about 550-µm2 for five-input proposed circuits, and would be negligibly increased for each extra input.

  12. 30 CFR 77.803 - Fail safe ground check circuits on high-voltage resistance grounded systems.

    Science.gov (United States)

    2010-07-01

    ... circuits on high-voltage resistance grounded systems. On and after September 30, 1971, all high-voltage, resistance grounded systems shall include a fail safe ground check circuit or other no less effective device... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Fail safe ground check circuits on...

  13. 30 CFR 75.803 - Fail safe ground check circuits on high-voltage resistance grounded systems.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Fail safe ground check circuits on high-voltage resistance grounded systems. 75.803 Section 75.803 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION... High-Voltage Distribution § 75.803 Fail safe ground check circuits on high-voltage resistance...

  14. Effect of Circuit Breaker Shunt Resistance on Chaotic Ferroresonance in Voltage Transformer

    Directory of Open Access Journals (Sweden)

    RADMANESH, H.

    2010-08-01

    Full Text Available Ferroresonance or nonlinear resonance is a complex electrical phenomenon, which may cause over voltages and over currents in the electrical power system which endangers the system reliability and continuous safe operating. This paper studies the effect of circuit breaker shunt resistance on the control of chaotic ferroresonance in a voltage transformer. It is expected that this resistance generally can cause ferroresonance dropout. For confirmation this aspect Simulation has been done on a one phase voltage transformer rated 100VA, 275kV. The magnetization characteristic of the transformer is modeled by a single-value two-term polynomial with q=7. The simulation results reveal that considering the shunt resistance on the circuit breaker, exhibits a great mitigating effect on ferroresonance over voltages. Significant effect on the onset of chaos, the range of parameter values that may lead to chaos along with ferroresonance voltages has been obtained and presented.

  15. A Protection Circuit for DC-DC Converter with Voltage Doubler

    Directory of Open Access Journals (Sweden)

    D.Elangovan

    2012-12-01

    Full Text Available This paper proposes a method to obtain a protected voltage gain by employing a protection circuit for the voltage doubler or multiplier circuit in an isolated tyde DC-DC Converter. The entire set up consists of a phase shift converter with a protected bridge/voltage doubler rectifier on the output side. The operating frequency of the phase shift converter is 20-25kHz (depending on the requirement of the application which is high enough to improve the efficiency. Ferrite core transformer is used in place of ordinary air core transformer, which is small in size with number of turns of the transformer is reduced and the overall power density is increased. The doubler circuit consists of electrolytic capacitors, which are rated at 400V in order to comply with IEC65 requirements. This paper proposes an “electrolytic capacitor protection circuit”, which enables the voltage rating of the electrolytics to be reduced to 250V. This circuit results in cost savings of more than 50% in the price of the electrolytic filter capacitors. The circuits were simulated using PSPICE SOFTWARE and the following results were obtained. For an input voltage of 200V, an output of 200V and400V were obtained in bridge mode and doubler mode respectively.

  16. Voltage-Sensitive Load Controllers for Voltage Regulation and Increased Load Factor in Distribution Systems

    DEFF Research Database (Denmark)

    Douglass, Philip James; Garcia-Valle, Rodrigo; Østergaard, Jacob

    2014-01-01

    consumption which can be mapped to temperature setpoint offsets of thermostat controlled loads. In networks where a lower voltage level corresponds to high system load (and vice versa), this controller acts to regulate voltage and increase the load factor. Simulations are conducted on low- and medium-voltage......This paper presents a novel controller design for controlling appliances based on local measurements of voltage. The controller finds the normalized voltage deviation accounting for the sensitivity of voltage measurements to appliance state. The controller produces a signal indicating desired power...... distribution systems with residential loads including voltage-sensitive water heaters. In low-voltage systems, the results of the simulations show the controller to be effective at reducing the extremes of voltage and increasing the load factor while respecting end-use temperature constraints. In medium-voltage...

  17. Using of capacitors for improving the electric power quality in the low voltage circuits; Utilizacao de capacitores para melhoria da qualidade de energia eletrica nos circuitos de baixa tensao

    Energy Technology Data Exchange (ETDEWEB)

    Fassheber Junior, Carlos Frederico [Centrais Eletricas de Santa Catarina (CELESC), Florianopolis, SC (Brazil)]. E-mail: cffassheber@celesc.com.br

    2000-07-01

    The paper discuss the application of a bank of low voltage capacitors which can provide reduction in the loading of the low voltage circuits and in the transformers, more regulation of the voltage, improvement in the power factor, besides the fact of they are natural harmonic filters.

  18. Voltage regulator for battery power source. [using a bipolar transistor

    Science.gov (United States)

    Black, J. M. (Inventor)

    1979-01-01

    A bipolar transistor in series with the battery as the control element also in series with a zener diode and a resistor is used to maintain a predetermined voltage until the battery voltage decays to very nearly the predetermined voltage. A field effect transistor between the base of the bipolar transistor and a junction between the zener diode and resistor regulates base current of the bipolar transistor, thereby regulating the conductivity of the bipolar transistor for control of the output voltage.

  19. Simulation Analysis for Opening Performance of Medium Voltage Vacuum Circuit Breaker Based on ADAMS and Maxwell

    Directory of Open Access Journals (Sweden)

    Ding Xianliang

    2017-01-01

    Full Text Available The circuit breakers play a important role in control and protect the power systemand the vacuum circuit breaker has beenwidely used in the field of medium voltage with its excellent opening performance.Virtual prototyping technology is alsobecamemore and more popularin design and optimization of the vacuum circuit breaker. In this paper, the electromagnetic simulation software Ansoft Maxwell is used to analyze the electric repulsion of the circuit breaker in the case of open the rated short circuit breaking current. The 3D model that wasbuilt by CREOis imported into ADAMS. Thenconstraints, contact force, and the electric repulsion forcethat was analysezed in Ansoft Maxwell is added into the 3D model.Therefore, we can carry on the multi-body dynamics simulation to the 3D model. Then We can get the openingperformance of the vacuum circuit breakerin the condition of open circuit rated short circuit breaking current. The simulation results show that the circuit breaker can still meet the performance requirements in the condition of open circuit rated short circuit breaking current.

  20. Comparison of Algorithms for Control of Loads for Voltage Regulation

    DEFF Research Database (Denmark)

    Douglass, Philip James; Han, Xue; You, Shi

    2014-01-01

    Autonomous flexible loads can be utilized to regulate voltag e on low voltage feeders. This paper compares two algorithms for controllin g loads: a simple voltage droop, where load power consumption is a varied in proportio n to RMS voltage; and a normalized relative voltage droop, which modifies...... the simpl e voltage droop by subtracting the mean voltage value at the bus and dividing by the standard deviation. These two controllers are applied to hot water heaters simul ated in a simple residential feeder. The simulation results show that both controllers r educe the frequency of undervoltage events...

  1. Programmable high voltage power supply with regulation confined to the high voltage section

    Science.gov (United States)

    Castell, Karen D. (Inventor); Ruitberg, Arthur P. (Inventor)

    1994-01-01

    A high voltage power supply in a dc-dc converter configuration includes a pre-regulator which filters and regulates the dc input and drives an oscillator which applies, in turn, a low voltage ac signal to the low side of a step-up high voltage transformer. The high voltage side of the transformer drives a voltage multiplier which provides a stepped up dc voltage to an output filter. The output voltage is sensed by a feedback network which then controls a regulator. Both the input and output of the regulator are on the high voltage side, avoiding isolation problems. The regulator furnishes a portion of the drive to the voltage multiplier, avoiding having a regulator in series with the load with its attendant, relatively high power losses. This power supply is highly regulated, has low power consumption, a low parts count and may be manufactured at low cost. The power supply has a programmability feature that allows for the selection of a large range of output voltages.

  2. Low-power operation using self-timed circuits and adaptive scaling of the supply voltage

    DEFF Research Database (Denmark)

    Nielsen, Lars Skovby; Niessen, C.; Sparsø, Jens

    1994-01-01

    Recent research has demonstrated that for certain types of applications like sampled audio systems, self-timed circuits can achieve very low power consumption, because unused circuit parts automatically turn into a stand-by mode. Additional savings may be obtained by combining the self...... of voltage scaling has been used previously in synchronous circuits, and the contributions of the present paper are: 1) the combination of supply scaling and self-timed circuitry which has some unique advantages, and 2) the thorough analysis of the power savings that are possible using this technique.>......-timed circuits with a mechanism that adaptively adjusts the supply voltage to the smallest possible, while maintaining the performance requirements. This paper describes such a mechanism, analyzes the possible power savings, and presents a demonstrator chip that has been fabricated and tested. The idea...

  3. Synchronous Generator Model with Fractional Order Voltage Regulator PIbDa

    Directory of Open Access Journals (Sweden)

    Dariusz Spałek

    2015-06-01

    Full Text Available Synchronous generator together with excitation circuit, voltage controller and system stabilizer constitute nonlinear ordinary differential equations set. The nonlinearity of differential equations set results from magnetic circuits saturation. One of the most important, from the electric energy distribution point of view, is the influence of voltage control applied on the generator voltage. There could be applied regulator either classical PID or fractional of type PIbDa which bases on the so-called fractional derivative idea. Numerical solutions of nonlinear differential equations set, that takes into account both magnetic circuits saturation and fractional regulator PIbDa, lead to decisions either to accept or to reject the chosen parameters. The sensibility of generator work on chosen fractional regulator parameters is the main aim of this paper. With the help of C++ program provided the most important states of work (short–circuit, setting voltage change, reactive power rejection can be analyzed basing on the accepted model of synchronous generator such as (1,1, (2,2 or (3,3.

  4. The Control Unit of a Single Phase Voltage Regulator

    CERN Document Server

    Colak, Ilknur

    2010-01-01

    Supplying regulated voltage to critical loads is an important topic for several years. This paper presents a single-phase electronic voltage regulator based on high frequency switching of an isolated transformer where primary side voltage is controlled by two full-bridge converters sharing a common DC bus and operating at 50Hz and 20kHz switching frequencies. This allows 50Hz induced voltage on the primary side of the transformer, regulated by high frequency switching. Depending on the input voltage, voltage at the secondary side of the transformer add to (boost mode) or subtract (buck mode) from the supply voltage, therefore, maintaining a regulated voltage value across the load. The regulator is controlled by a digital controller allowing fast dynamic response. A 5kVA single-phase voltage regulator is realized to verify the operation of the proposed algorithm. The experimental results show that regulator maintains constant voltage across the load both in step-up (low supply voltage) and step-down (high supp...

  5. Control strategy and hardware implementation for DC–DC boost power circuit based on proportional–integral compensator for high voltage application

    Directory of Open Access Journals (Sweden)

    Sanjeevikumar Padmanaban

    2015-06-01

    Full Text Available For high-voltage (HV applications, the designers mostly prefer the classical DC–DC boost converter. However, it lacks due to the limitation of the output voltage by the gain transfer ratio, decreased efficiency and its requirement of two sensors for feedback signals, which creates complex control scheme with increased overall cost. Furthermore, the output voltage and efficiency are reduced due to the self-parasitic behavior of power circuit components. To overcome these drawbacks, this manuscript provides, the theoretical development and hardware implementation of DC–DC step-up (boost power converter circuit for obtaining extra output-voltage high-performance. The proposed circuit substantially improves the high output-voltage by voltage-lift technology with a closed loop proportional–integral controller. This complete numerical model of the converter circuit including closed loop P-I controller is developed in simulation (Matlab/Simulink software and the hardware prototype model is implemented with digital signal processor (DSP TMS320F2812. A detailed performance analysis was carried out under both line and load regulation conditions. Numerical simulation and its verification results provided in this paper, prove the good agreement of the circuit with theoretical background.

  6. Background voltage distortion influence on power electric systems in the presence of the Steinmetz circuit

    Energy Technology Data Exchange (ETDEWEB)

    Sainz, Luis; Pedra, Joaquin [Department of Electrical Engineering, ETSEIB-UPC, Av. Diagonal 647, 08028 Barcelona (Spain); Caro, Manuel [IDOM Ingenieria y Arquitectura, C. Barcas 2, 46002 Valencia (Spain)

    2009-01-15

    In traction systems, it is usual to connect reactances in delta configuration with single-phase loads to reduce voltage unbalances and avoid electric system operation problems. This set is known as Steinmetz circuit. Parallel and series resonances can occur due to the capacitive reactance of the Steinmetz circuit and affect power quality. In this paper, the series resonance ''observed'' from the supply system is numerically located. The study of this resonance is important to avoid problems due to background voltage distortion. Experimental measurements are also presented to validate the obtained numerical results. (author)

  7. On-line Monitoring System based on Vibration Signal of High Voltage Circuit Breaker

    Directory of Open Access Journals (Sweden)

    Chao Fu

    2014-04-01

    Full Text Available High voltage circuit breaker is one of the most important switch apparatus in electrical power system. It play a role in the switch control, which can be used to switch the operating mode during normal operation (the equipment run or quit. In order to ensure the normal operation of the grid, it can be removed quickly when a malfunction on the device or circuit. Real-time online monitoring of high voltage circuit breaker can understand the running status, master the operation characteristics and its tend of development. As early as possible find the potential faults then take preventive measures timely, so as to ensure the reliable operation of power system. Online monitoring of high voltage circuit breakers can reduce the premature or unnecessary maintenance and maintenance cost, improve pertinence of the maintenance firstly. Secondly, it can improve the life of the switching device and improve the reliability of electric power system significantly. In this paper, on-line monitoring system based on vibration signal of high voltage circuit breaker is presented

  8. Nonfullerene Tandem Organic Solar Cells with High Open-Circuit Voltage of 1.97 V.

    Science.gov (United States)

    Liu, Wenqing; Li, Shuixing; Huang, Jiang; Yang, Shida; Chen, Jiehuan; Zuo, Lijian; Shi, Minmin; Zhan, Xiaowei; Li, Chang-Zhi; Chen, Hongzheng

    2016-11-01

    Small-molecule nonfullerene-based tandem organic solar cells (OSCs) are fabricated for the first time by utilizing P3HT:SF(DPPB)4 and PTB7-Th:IEIC bulk heterojunctions as the front and back subcells, respectively. A power conversion efficiency of 8.48% is achieved with an ultrahigh open-circuit voltage of 1.97 V, which is the highest voltage value reported to date among efficient tandem OSCs.

  9. Operating Circuit Fault Diagnosis of High Voltage Circuit Breaker%高压断路器操作回路的故障诊断

    Institute of Scientific and Technical Information of China (English)

    赵红宇; 龙树峰

    2015-01-01

    This paper analyzes and studies the fault diagnosis operation requirements of high voltage circuit breaker operation circuit and the fault diagnosis method of high voltage circuit breaker.%本文对高压断路器操作回路的故障诊断操作要求和高压断路器操作回路的故障诊断方法进行了分析和研究。

  10. Complemenary body driving - a low voltage analog circuit technique for SOI

    Science.gov (United States)

    Mojarradi, M. M.; Terry, S.; Blalock, B. J.; Yong, L.; Dufrene, B.

    2002-01-01

    This paper describes several analog circuit primitives that utilize the body terminal as a signal port. A cascode current mirror that can operate with an input and output voltage of 200 mV; and a rail-to-rail, constant transconductance gain block capable of 1 V operation are presented. These circuits have been implemented in a standard 0.351 partially-depleted Silicon-on-Insulator (PDSOI) CMOS process and should find wide application in next-generation analog circuit designs.

  11. Ultra-low-voltage design of energy-efficient digital circuits

    CERN Document Server

    Reynders, Nele

    2015-01-01

    This book focuses on increasing the energy-efficiency of electronic devices so that portable applications can have a longer stand-alone time on the same battery. The authors explain the energy-efficiency benefits that ultra-low-voltage circuits provide and provide answers to tackle the challenges which ultra-low-voltage operation poses. An innovative design methodology is presented, verified, and validated by four prototypes in advanced CMOS technologies. These prototypes are shown to achieve high energy-efficiency through their successful functionality at ultra-low supply voltages.

  12. Battery open-circuit voltage estimation by a method of statistical analysis

    NARCIS (Netherlands)

    Snihir, Iryna; Rey, William; Verbitskiy, Evgeny; Belfadhel-Ayeb, Afifa; Notten, Peter H.L.

    2006-01-01

    The basic task of a battery management system (BMS) is the optimal utilization of the stored energy and minimization of degradation effects. It is critical for a BMS that the state-of-charge (SoC) be accurately determined. Open-circuit voltage (OCV) is directly related to the state-of-charge of the

  13. Transistorized Marx bank pulse circuit provides voltage multiplication with nanosecond rise-time

    Science.gov (United States)

    Jung, E. A.; Lewis, R. N.

    1968-01-01

    Base-triggered avalanche transistor circuit used in a Marx bank pulser configuration provides voltage multiplication with nanosecond rise-time. The avalanche-mode transistors replace conventional spark gaps in the Marx bank. The delay time from an input signal to the output signal to the output is typically 6 nanoseconds.

  14. Improvement of high-voltage staircase drive circuit waveform for high-intensity therapeutic ultrasound

    Science.gov (United States)

    Tamano, Satoshi; Jimbo, Hayato; Azuma, Takashi; Yoshizawa, Shin; Fujiwara, Keisuke; Itani, Kazunori; Umemura, Shin-Ichiro

    2016-07-01

    Recently, in the treatment of diseases such as cancer, noninvasive or low-invasive modality, such as high-intensity focused ultrasound (HIFU), has been put into practice as an alternative to open surgery. HIFU induces thermal ablation of the target tissue to be treated. To improve the efficiency of HIFU, we have proposed a “triggered-HIFU” technique, which uses the combination of a short-duration, high-voltage transmission and a long-duration, medium-voltage transmission. In this method, the transmission device must endure high peak voltage for the former and the high time-average power for the latter. The triggered-HIFU sequence requires electronic scanning of the HIFU focus to maximize its thermal efficiency. Therefore, the transmission device must drive an array transducer with the number of elements on the order of a hundred or more, which requires that each part of the device that drives each element must be compact. The purpose of this work is to propose and construct such a transmission device by improving the staircase drive circuit, which we previously proposed. The main point of improvement is that both N and P MOSFETs are provided for each staircase voltage level instead of only one of them. Compared with the previous ultrasonic transmission circuit, high-voltage spikes were significantly reduced, the power consumption was decreased by 26.7%, and the transmission circuit temperature rise was decreased by 14.5 °C in the triggered-HIFU heating mode.

  15. Demonstration of a High Open-Circuit Voltage GaN Betavoltaic Microbattery

    Institute of Scientific and Technical Information of China (English)

    CHENG Zai-Jun; SAN Hai-Sheng; CHEN Xu-Yuan; LIU Bo; FENG Zhi-Hong

    2011-01-01

    A high open-circuit voltage betavoltaic microbattery based on a GaN p-i-n diode is demonstrated.Under the irradiation of a 4× 4mm2 planar solid 63Ni source with an activity of 2mCi,the open-circuit voltage Voc of the fabricated single 2x2mm2 cell reaches as high as 1.62 V,the short-circuit current density Jsc is measured to be 16nA/cm2.The microbattery has a fill factor of 55%,and the energy conversion effciency of beta radiation into electricity reaches to 1.13%.The results suggest that GaN is a highly promising potential candidate for long-life betavoltaic microbatteries used as power supplies for microelectromechanical system devices.

  16. Modeling of the Voltage Waves in the LHC Main Dipole Circuits

    CERN Document Server

    Ravaioli, E; Formenti, F; Steckert, J; Thiesen, H; Verweij, A

    2012-01-01

    When a fast power abort is triggered in the LHC main dipole chain, voltage transients are generated at the output of the power converter and across the energy-extraction switches. The voltage waves propagate through the chain of 154 superconducting dipoles and can have undesired effects leading to spurious triggering of the quench protection system and firing of the quench heaters. The phase velocity of the waves travelling along the chain changes due to the inhomogeneous AC behavior of the dipoles. Furthermore, complex phenomena of reflection and superposition are present in the circuit. For these reasons analytical calculations are not sufficient for properly analyzing the circuit behavior after a fast power abort. The transients following the switch-off of the power converter and the opening of the switches are analyzed by means of a complete electrical model, developed with the Cadence© suite (PSpice© based). The model comprises all the electrical components of the circuit, additional components simula...

  17. Design and validation of a high-voltage levitation circuit for electrostatic accelerometers.

    Science.gov (United States)

    Li, G; Wu, S C; Zhou, Z B; Bai, Y Z; Hu, M; Luo, J

    2013-12-01

    A simple high-voltage circuit with a voltage range of 0 to 900 V and an open-loop bandwidth of 11 kHz is realized by using an operational amplifier and a MOSFET combination. The circuit is used for the levitation of a test mass of 71 g, suspended below the top-electrodes with a gap distance of 57 μm, so that the performance of an electrostatic accelerometer can be tested on the ground. The translation noise of the accelerometer, limited by seismic noise, is about 4 × 10(-8) m/s(2)/Hz(1/2) at 0.1 Hz, while the high-voltage coupling noise is one-order of magnitude lower.

  18. Thermodynamic derivation of open circuit voltage in vanadium redox flow batteries

    Science.gov (United States)

    Pavelka, Michal; Wandschneider, Frank; Mazur, Petr

    2015-10-01

    Open circuit voltage of vanadium redox flow batteries is carefully calculated using equilibrium thermodynamics. This analysis reveals some terms in the Nernst relation which are usually omitted in literature. Due to the careful thermodynamic treatment, all uncertainties about the form of Nernst relation are removed except for uncertainties in activity coefficients of particular species. Moreover, it is shown (based again on equilibrium thermodynamics) that batteries with anion-exchange membranes follow different Nernst relation than batteries with cation-exchange membranes. The difference is calculated, and it is verified experimentally that the formula for anion-exchange membranes describes experiments with anion-exchange membranes better than the corresponding formula for cation-exchange membranes. In summary, careful thermodynamic calculation of open circuit voltage of vanadium redox flow batteries is presented, and the difference between voltage for anion-exchange and cation-exchange membranes is revealed.

  19. Effect of polymer aggregation on the open circuit voltage in organic photovoltaic cells: aggregation-induced conjugated polymer gel and its application for preventing open circuit voltage drop.

    Science.gov (United States)

    Kim, Bong-Gi; Jeong, Eun Jeong; Park, Hui Joon; Bilby, David; Guo, L Jay; Kim, Jinsang

    2011-03-01

    To investigate the structure-dependent aggregation behavior of conjugated polymers and the effect of aggregation on the device performance of conjugated polymer photovoltaic cells, new conjugated polymers (PVTT and CN-PVTT) having the same regioregularity but different intermolecular packing were prepared and characterized by means of UV-vis spectroscopy and atomic force microscopy (AFM). Photovoltaic devices were prepared with these polymers under different polymer-aggregate conditions. Polymer aggregation induced by thermal annealing increases the short circuit current but provides no advantage in the overall power conversion efficiency because of a decrease in the open circuit voltage. The device fabricated from a pre-aggregated polymer suspension, acquired from ultrasonic agitation of a conjugated polymer gel, showed enhanced performance because of better phase separation and reduced recombination between polymer/PCBM.

  20. Distance protection of multiple-circuit shared tower transmission lines with different voltages. Part II: Fault loop impedance

    DEFF Research Database (Denmark)

    Silva, Filipe Miguel Faria da; Bak, Claus Leth

    2017-01-01

    Multiple-circuit transmission lines combining different voltage levels in one tower present extra challenges when setting a protection philosophy, as faults between voltage levels are possible. In this paper, the fault loop impedance of combined faults is compared with the fault loop impedance...... of single-phase-to-ground faults at the higher voltage level of the multiple-circuit line and it is demonstrated that they are similar for high short-circuit powers; however, the fault loop impedance of a combined fault may increase substantially as the short-circuit power of the system decreases......-phase-to-ground faults are also capable of protecting the line against combined faults, being only advisable to increase the resistive limit of the protection zone if the network has lower short-circuit power. If the length of the line at lower voltage level is less than of the lien at higher voltage level...

  1. Fractional-order Systems and Synchronous Generator Voltage Regulator

    Directory of Open Access Journals (Sweden)

    Wojciech Lubośny

    2015-03-01

    Full Text Available Modern regulators of synchronous generators, including voltage regulators, are digital systems, in their vast majority with standard structures contained in the IEEE standard. These are systems described with stationary differential equations of integral order. Differential equations of fractional order are not employed in regulators for synchronous generator control. This paper presents an analysis of the possibilities of using a system of fractional differential equations in the voltage regulator of an synchronous generator with a static excitation system.

  2. Application of thyristor in voltage regulation%晶闸管在调压技术中的应用

    Institute of Scientific and Technical Information of China (English)

    刘晓青; 刘伟

    2011-01-01

    阐述了晶闸管的工作特性,主要从晶闸管整流电路和晶闸管交流调压电路两方面,分析了如何利用晶闸管的特性进行调压.%The paper described the work characteristics of the thyristor, and analyzed how to adjust the voltage using the characteristics of the thyristor, mainly including rectifier circuit and Ac voltage regulation circuit with thyristors. Analysis showed that voltage controllers with thyristors are widely used in various industries because of its simpleness and practicality.

  3. A band-gap voltage reference for interface circuit of microsensor

    Institute of Scientific and Technical Information of China (English)

    CAO Yi-jiang; XIAO Fei; ZHANG Er-dong

    2010-01-01

    A high performance CMOS band-gap voltage reference circuit that can be used in interface integrated circuit of microsenser and compatible with 0.6 μm (double poly) mix process is proposed in this paper.The circuit can be employed in the range of 1.8-8 V and carry out the first-order PTAT (proportional to absolute temperature) temperature compensation.Through using a two-stage op-amp with a NMOS input pair as a negative feedback op-amp,the PSRR (power supply rejection ratio) of the entire circuit is increased,and the temperature coefficient of reference voltage is decreased.Results from HSPICE simulation show that the PSRR is -72.76 dB in the condition of low-frequency,the temperature coefficient is 2.4×10-6 in the temperature range from-10 ℃ to 90℃ and the power dissipation is only 14 μW when the supply voltage is 1.8 V.

  4. Protocadherin 17 regulates presynaptic assembly in topographic corticobasal Ganglia circuits.

    Science.gov (United States)

    Hoshina, Naosuke; Tanimura, Asami; Yamasaki, Miwako; Inoue, Takeshi; Fukabori, Ryoji; Kuroda, Teiko; Yokoyama, Kazumasa; Tezuka, Tohru; Sagara, Hiroshi; Hirano, Shinji; Kiyonari, Hiroshi; Takada, Masahiko; Kobayashi, Kazuto; Watanabe, Masahiko; Kano, Masanobu; Nakazawa, Takanobu; Yamamoto, Tadashi

    2013-06-05

    Highly topographic organization of neural circuits exists for the regulation of various brain functions in corticobasal ganglia circuits. Although neural circuit-specific refinement during synapse development is essential for the execution of particular neural functions, the molecular and cellular mechanisms for synapse refinement are largely unknown. Here, we show that protocadherin 17 (PCDH17), one of the nonclustered δ2-protocadherin family members, is enriched along corticobasal ganglia synapses in a zone-specific manner during synaptogenesis and regulates presynaptic assembly in these synapses. PCDH17 deficiency in mice causes facilitated presynaptic vesicle accumulation and enhanced synaptic transmission efficacy in corticobasal ganglia circuits. Furthermore, PCDH17(-/-) mice exhibit antidepressant-like phenotypes that are known to be regulated by corticobasal ganglia circuits. Our findings demonstrate a critical role for PCDH17 in the synaptic development of specific corticobasal ganglia circuits and suggest the involvement of PCDH17 in such circuits in depressive behaviors.

  5. Anomalous open-circuit voltage from a high-Tc superconducting dynamo

    Science.gov (United States)

    Bumby, C. W.; Jiang, Zhenan; Storey, J. G.; Pantoja, A. E.; Badcock, R. A.

    2016-03-01

    We report on the behavior of a high-Tc superconducting (HTS) homopolar dynamo which outputs a DC open-circuit voltage when the stator is in the superconducting state, but behaves as a conventional AC alternator when the stator is in the normal state. We observe that this time-averaged DC voltage arises from a change in the shape of the AC voltage waveform that is obtained from a normal conducting stator. The measured DC voltage is proportional to frequency, and decreases with increasing flux gap between the rotor magnet and the HTS stator wire. We observe that the DC output voltage decreases to zero at large flux gaps, although small differences between the normal-conducting and superconducting waveforms are still observed, which we attribute to screening currents in the HTS stator wire. Importantly, the normalised pulse shape is found to be a function of the rotor position angle only. Based on these observations, we suggest that the origin of this unexpected DC effect can be explained by a model first proposed by Giaever, which considers the impact of time-varying circulating eddy currents within the HTS stator wire. Such circulating currents form a superconducting shunt path which "short-circuits" the high field region directly beneath the rotor magnet, at those points in the cycle when the rotor magnet partially overlaps the superconducting stator wire. This reduces the output voltage from the device during these periods of the rotor cycle, leading to partial rectification of the output voltage waveform and hence the emergence of a time-averaged DC voltage.

  6. Flexible and low-voltage integrated circuits constructed from high-performance nanocrystal transistors.

    Science.gov (United States)

    Kim, David K; Lai, Yuming; Diroll, Benjamin T; Murray, Christopher B; Kagan, Cherie R

    2012-01-01

    Colloidal semiconductor nanocrystals are emerging as a new class of solution-processable materials for low-cost, flexible, thin-film electronics. Although these colloidal inks have been shown to form single, thin-film field-effect transistors with impressive characteristics, the use of multiple high-performance nanocrystal field-effect transistors in large-area integrated circuits has not been shown. This is needed to understand and demonstrate the applicability of these discrete nanocrystal field-effect transistors for advanced electronic technologies. Here we report solution-deposited nanocrystal integrated circuits, showing nanocrystal integrated circuit inverters, amplifiers and ring oscillators, constructed from high-performance, low-voltage, low-hysteresis CdSe nanocrystal field-effect transistors with electron mobilities of up to 22 cm(2) V(-1) s(-1), current modulation >10(6) and subthreshold swing of 0.28 V dec(-1). We fabricated the nanocrystal field-effect transistors and nanocrystal integrated circuits from colloidal inks on flexible plastic substrates and scaled the devices to operate at low voltages. We demonstrate that colloidal nanocrystal field-effect transistors can be used as building blocks to construct complex integrated circuits, promising a viable material for low-cost, flexible, large-area electronics.

  7. Pressure and Arc Voltage Measurement in a 252 kV SF6 Puffer Circuit Breaker

    Institute of Scientific and Technical Information of China (English)

    ZHONG Jianying; GUO Yujing; ZHANG Hao

    2016-01-01

    The pressure distribution in an arcing chamber is critically important for the SF6 puffer circuit breaker design.In this paper,the pressure variation of four locations in the nozzle was measured by piezoresistive and fiber optical pressure sensors at two current levels of 10 kA and 50 kA.An arc voltage measurement was also taken.The results demonstrate that using either type of sensor with a connecting tube is able to detect the fast pressure variation in circuit breakers,however the possible distortion and delay to the pressure transient caused by the tube need further study.

  8. FEA identification of high order generalized equivalent circuits for MF high voltage transformers

    CERN Document Server

    Candolfi, Sylvain; Cros, Jérôme; Aguglia, Davide

    2015-01-01

    This paper presents a specific methodology to derive high order generalized equivalent circuits from electromagnetic finite element analysis for high voltage medium frequency and pulse transformers by splitting the main windings in an arbitrary number of elementary windings. With this modeling approach, the dynamic model of the transformer over a large bandwidth is improved and the order of the generalized equivalent circuit can be adapted to a specified bandwidth. This efficient tool can be used by the designer to quantify the influence of the local structure of transformers on their dynamic behavior. The influence of different topologies and winding configurations is investigated. Several application examples and an experimental validation are also presented.

  9. Pressure and Arc Voltage Measurement in a 252 kV SF6 Puffer Circuit Breaker

    Science.gov (United States)

    Zhong, Jianying; Guo, Yujing; Zhang, Hao

    2016-05-01

    The pressure distribution in an arcing chamber is critically important for the SF6 puffer circuit breaker design. In this paper, the pressure variation of four locations in the nozzle was measured by piezoresistive and fiber optical pressure sensors at two current levels of 10 kA and 50 kA. An arc voltage measurement was also taken. The results demonstrate that using either type of sensor with a connecting tube is able to detect the fast pressure variation in circuit breakers, however the possible distortion and delay to the pressure transient caused by the tube need further study.

  10. Evaluation and Simulation of Black-box Arc Models for High-Voltage Circuit-Breakers

    OpenAIRE

    Gustavsson, Niklas

    2004-01-01

    The task for this Master thesis was to evaluate different black-box arc models for circuit-breakers with the purpose of finding criteria for the breaking ability. A black-box model is a model that requires no knowledge from the user of the underlying physical processes. Black-box arc models have been used in circuit-breaker development for many years. Arc voltages from tests made in the High Power Laboratory in Ludvika were used for validation, along with the resistance calculated at current ...

  11. A Low Input Current and Wide Conversion Ratio Buck Regulator with 75% Efficiency for High-Voltage Triboelectric Nanogenerators

    Science.gov (United States)

    Luo, Li-Chuan; Bao, De-Chun; Yu, Wu-Qi; Zhang, Zhao-Hua; Ren, Tian-Ling

    2016-01-01

    It is meaningful to research the Triboelectric Nanogenerators (TENG), which can create electricity anywhere and anytime. There are many researches on the structures and materials of TENG to explain the phenomenon that the maximum voltage is stable and the current is increasing. The output voltage of the TENG is high about 180-400 V, and the output current is small about 39 μA, which the electronic devices directly integration of TENG with Li-ion batteries will result in huge energy loss due to the ultrahigh TENG impedance. A novel interface circuit with the high-voltage buck regulator for TENG is introduced firstly in this paper. The interface circuit can transfer the output signal of the TENG into the signal fit to a lithium ion battery. Through the circuit of the buck regulator, the average output voltage is about 4.0 V and the average output current is about 1.12 mA. Further, the reliability and availability for the lithium ion battery and the circuit are discussed. The interface circuit is simulated using the Cadence software and verified through PCB experiment. The buck regulator can achieve 75% efficiency for the High-Voltage TENG. This will lead to a research hot and industrialization applications.

  12. Simulation of the Effects of Several Factors on Arc Plasma Behavior in Low Voltage Circuit Breaker

    Institute of Scientific and Technical Information of China (English)

    2005-01-01

    Taking into account the properties of the arc plasma and the electromagnetic, heat and radiative phenomena, commercial computational fluid dynamics software PHOENICS has been adapted and modified to develop the three-dimensional magneto-hydrodynamic (MHD)model of arc in a low voltage circuit breaker. The effects of the arc ignition location, venting size and gassing material on arc behavior have been investigated. The analysis of the results show that the arc velocity accelerates with the increase in the distance between arc ignition location and of the venting size, and the existence of the gassing material is beneficial to improving the arc voltage and reducing the arc temperature.

  13. A test technique for measuring lightning-induced voltages on aircraft electrical circuits

    Science.gov (United States)

    Walko, L. C.

    1974-01-01

    The development of a test technique used for the measurement of lightning-induced voltages in the electrical circuits of a complete aircraft is described. The resultant technique utilizes a portable device known as a transient analyzer capable of generating unidirectional current impulses similar to lightning current surges, but at a lower current level. A linear relationship between the magnitude of lightning current and the magnitude of induced voltage permitted the scaling up of measured induced values to full threat levels. The test technique was found to be practical when used on a complete aircraft.

  14. Design to conditioning circuits of dynamic compensation of reactive power in the intelligence voltage controller

    Institute of Scientific and Technical Information of China (English)

    2010-01-01

    <正>The paper introduces one design idea that making use of SCM to control Real-timely the dynamic compensation of reactive power.Firstly,design one Circuit to Sample the voltage and current,and by these datas we can easily calculate the power factor,and Voltage controller in the microcontroller to determine whether input the compensation capacitance according to the size of power factor,the paper also analyzes the principle of capacitance compensation and calculation method. Dynamic compensation for the entire process is quick and accurate.

  15. Performance of Three-Arm Ac Automatic Voltage Regulator

    Directory of Open Access Journals (Sweden)

    T. Papinaidu

    2014-04-01

    Full Text Available In this paper the design and simulation of automatic voltage regulator (AVR is proposed. The AVR provides voltage buck and boost capability to eliminate power problems created by under voltage or over voltage fluctuations. It also protects against minor and severe spikes and surges that comprise over 80% of power problems. Over heating of components due to voltage swell is also avoided by using AVR. The switching losses are also reduced as only one arm among three arms is maintained at higher power frequencies depending on mode of operation. Moreover, there is no need to use large capacitor as a result the overall size of converter is also reduced. Hence, the output voltage of the AVR can be maintained at the specified voltage. Hence, the AVR is cost can be reduced, and the efficiency of the power convertor can be extended.

  16. Origin of the high open circuit voltage in planar heterojunction perovskite solar cells: Role of the reduced bimolecular recombination

    Science.gov (United States)

    Yang, Wenchao; Yao, Yao; Wu, Chang-Qin

    2015-03-01

    The high open circuit voltage is an attractive feature for the currently popular organic-inorganic hybrid perovskite solar cells. In this paper, by employing the macroscopic device model simulation, we investigate its origin for the planar heterojunction perovskite solar cells. Based on the calculated current density-voltage characteristics, it is revealed that compared to the excitonic solar cells, the fast thermal-activated exciton dissociation in the bulk due to the small exciton binding energy may improve the short circuit current and the fill factor, but its beneficial role on the open circuit voltage is marginal. The most significant contribution for the open circuit voltage comes from the reduced bimolecular recombination. In the perovskites, with the recombination prefactor many orders of magnitude smaller than that based on the Langevin's theory, the internal charge density level is significantly enhanced and the density gradient is removed, leading to the high quasi-Fermi level splitting and thus the small open circuit voltage loss. For the nonradiative recombination pathway due to the deep trap states, it may induce significant loss of open circuit voltage as the trap density is high, while for the moderately low density its effect on the open circuit voltage is small and negligible.

  17. The Effect of Current-Limiting Reactors on the Tripping of Short Circuits in High-Voltage Electrical Equipment

    Energy Technology Data Exchange (ETDEWEB)

    Volkov, M. S.; Gusev, Yu. P., E-mail: GusevYP@mpei.ru; Monakov, Yu. V.; Cho, Gvan Chun [National Research University “Moscow Power Engineering Institute,” (Russian Federation)

    2016-01-15

    The insertion of current-limiting reactors into electrical equipment operating at a voltage of 110 and 220 kV produces a change in the parameters of the transient recovery voltages at the contacts of the circuit breakers for disconnecting short circuits, which could be the reason for the increase in the duration of the short circuit, damage to the electrical equipment and losses in the power system. The results of mathematical modeling of the transients, caused by tripping of the short circuit in a reactive electric power transmission line are presented, and data are given on the negative effect of a current-limiting resistor on the rate of increase and peak value of the transient recovery voltages. Methods of ensuring the standard requirements imposed on the parameters of the transient recovery voltages when using current-limiting reactors in the high-voltage electrical equipment of power plants and substations are proposed and analyzed.

  18. A quasi-3-dimensional simulation method for a high-voltage level-shifting circuit structure

    Institute of Scientific and Technical Information of China (English)

    Liu Jizhi; Chen Xingbi

    2009-01-01

    A new quasi-three-dimensional (quasi-3D) numeric simulation method for a high-voltage level-shifting circuit structure is proposed. The performances of the 3D structure are analyzed by combining some 2D device structures; the 2D devices are in two planes perpendicular to each other and to the surface of the semiconductor. In comparison with Davinci, the full 3D device simulation tool, the quasi-3D simulation method can give results for the potential and current distribution of the 3D high-voltage level-shifting circuit structure with appropriate accuracy and the total CPU time for simulation is significantly reduced. The quasi-3D simulation technique can be used in many cases with advantages such as saving computing time, making no demands on the high-end computer terminals, and being easy to operate.

  19. Research on The Mechanical State Parameter Extraction Method of High Voltage Circuit Breakers

    Directory of Open Access Journals (Sweden)

    Yang Tianxu

    2013-05-01

    Full Text Available High voltage circuit breakers play an important role in the power system. So it is necessary to implement the state detection of breakers in order to ensure stable and reliable running of the grid. The purpose of state detection is to provide reliable basis of maintenance by extracting mechanical state parameters accurately. This paper mainly focuses on the coil current signal feature extraction algorithm. To settle the problem of too much noise mixed with the current signal and signal distortion, the discrete wavelet transform algorithm is used to extract the coil current signal parameters. This paper also designs the FIR filter to extract stroke and speed parameters from travel-time waveform. The experiments show that the difference between the theoretical results and test results processed by the method in this paper is very small and the test results are able to accurately reflect operation states and mechanical features of high voltage circuit breakers.

  20. A low-power circuit for piezoelectric vibration control by synchronized switching on voltage sources

    CERN Document Server

    Shen, Hui; Ji, Hongli; Zhu, Kongjun; Balsi, Marco; Giorgio, Ivan; dell'Isola, Francesco

    2010-01-01

    In the paper, a vibration damping system powered by harvested energy with implementation of the so-called SSDV (synchronized switch damping on voltage source) technique is designed and investigated. In the semi-passive approach, the piezoelectric element is intermittently switched from open-circuit to specific impedance synchronously with the structural vibration. Due to this switching procedure, a phase difference appears between the strain induced by vibration and the resulting voltage, thus creating energy dissipation. By supplying the energy collected from the piezoelectric materials to the switching circuit, a new low-power device using the SSDV technique is proposed. Compared with the original self-powered SSDI (synchronized switch damping on inductor), such a device can significantly improve its performance of vibration control. Its effectiveness in the single-mode resonant damping of a composite beam is validated by the experimental results.

  1. Distance protection of multiple-circuit shared tower transmission lines with different voltages. Part I: Fault current magnitude

    DEFF Research Database (Denmark)

    Silva, Filipe Miguel Faria da; Bak, Claus Leth

    2017-01-01

    Multiple-circuit transmission lines combining different voltage levels in one tower present extra challenges when setting a protection philosophy, as faults between voltage levels are possible. This paper presents a detailed theoretical analysis of such combined faults, including the development...... of a formula for estimating the magnitude of the short-circuit current. It is demonstrated that if the faulted phase from the higher voltage level leads the faulted phase from the lower voltage level, a distance relay at the higher voltage level sees the fault in the forward direction, whereas a distance relay...... at the lower voltage level sees the fault in the reverse direction. The opposite happens if the lower voltage level leads the higher voltage level. It is also demonstrated that the magnitude of fault currents of combined faults is normally slightly larger than of equivalent single-phase-to-ground fault...

  2. Power lateral pnp transistor operating with high current density in irradiated voltage regulator

    Directory of Open Access Journals (Sweden)

    Vukić Vladimir Đ.

    2013-01-01

    Full Text Available The operation of power lateral pnp transistors in gamma radiation field was examined by detection of the minimum dropout voltage on heavily loaded low-dropout voltage regulators LM2940CT5, clearly demonstrating their low radiation hardness, with unacceptably low values of output voltage and collector-emitter voltage volatility. In conjunction with previous results on base current and forward emitter current gain of serial transistors, it was possible to determine the positive influence of high load current on a slight improvement of voltage regulator LM2940CT5 radiation hardness. The high-current flow through the wide emitter aluminum contact of the serial transistor above the isolation oxide caused intensive annealing of the positive oxide-trapped charge, leading to decrease of the lateral pnp transistor's current gain, but also a more intensive recovery of the small-signal npn transistors in the control circuit. The high current density in the base area of the lateral pnp transistor immediately below the isolation oxide decreased the concentration of negative interface traps. Consequently, the positive influence of the reduced concentration of the oxide-trapped charge on the negative feedback reaction circuit, together with the favourable effect of reduced interface traps concentration, exceeded negative influence of the annealed oxide-trapped charge on the serial pnp transistor's forward emitter current gain.

  3. Relationship of Open-Circuit Voltage to CdTe Hole Concentration and Lifetime

    Energy Technology Data Exchange (ETDEWEB)

    Duenow, Joel N.; Burst, James M.; Albin, David S.; Reese, Matthew O.; Jensen, Soren A.; Johnston, Steven W.; Kuciauskas, Darius; Swain, Santosh K.; Ablekim, Tursun; Lynn, Kelvin G.; Fahrenbruch, Alan L.; Metzger, Wyatt K.

    2016-11-01

    We investigate the correlation of bulk CdTe and CdZnTe material properties with experimental open-circuit voltage (Voc) through fabrication and characterization of diverse single-crystal solar cells with different dopants. Several distinct crystal types reach Voc >900 mV. Correlations are in general agreement with Voc limits modeled from bulk minority-carrier lifetime and hole concentration.

  4. Driving CZTS to the SQ Limit: Solving the Open Circuit Voltage Problem

    Energy Technology Data Exchange (ETDEWEB)

    Haight, Richard A. [IBM Research, Yorktown, NY (United States). Thomas J. Watson Research Center; McCandless, Brian E. [Univ. of Delaware, Newark, DE (United States); Kummel, Andrew C. [Univ. of California, San Diego, CA (United States); Gordon, Roy G. [Harvard Univ., Cambridge, MA (United States)

    2016-12-15

    A key objective of this 3 year research effort was to reduce the open circuit voltage (Voc) deficit, defined as the difference between the absorber band gap and the measured Voc to below 475mV from values at the beginning of this work of 630-730mV. To achieve this reduction, along with the attendant goals of higher Voc and efficiency, detailed studies into the fundamental understanding of existing limitations were undertaken.

  5. Thermoacoustic and thermoreflectance imaging of biased integrated circuits: Voltage and temperature maps

    Science.gov (United States)

    Hernández-Rosales, E.; Cedeño, E.; Hernandez-Wong, J.; Rojas-Trigos, J. B.; Marin, E.; Gandra, F. C. G.; Mansanares, A. M.

    2016-07-01

    In this work a combined thermoacoustic and thermoreflectance set-up was designed for imaging biased microelectronic circuits. In particular, it was used with polycrystalline silicon resistive tracks grown on a monocrystalline Si substrate mounted on a test chip. Thermoreflectance images, obtained by scanning a probe laser beam on the sample surface, clearly show the regions periodically heated by Joule effect, which are associated to the electric current distribution in the circuit. The thermoacoustic signal, detected by a pyroelectric/piezoelectric sensor beneath the chip, also discloses the Joule contribution of the whole sample. However, additional information emerges when a non-modulated laser beam is focused on the sample surface in a raster scan mode allowing imaging of the sample. The distribution of this supplementary signal is related to the voltage distribution along the circuit.

  6. Thermoacoustic and thermoreflectance imaging of biased integrated circuits: Voltage and temperature maps

    Energy Technology Data Exchange (ETDEWEB)

    Hernández-Rosales, E.; Cedeño, E. [Gleb Wataghin Physics Institute, University of Campinas - Unicamp, 13083-859 Campinas, SP (Brazil); Instituto Politécnico Nacional, Centro de Investigación en Ciencia Aplicada y Tecnología Avanzada, Legaria 694, Colonia Irrigación, CP 11500, México, DF (Mexico); Hernandez-Wong, J. [Instituto Politécnico Nacional, Centro de Investigación en Ciencia Aplicada y Tecnología Avanzada, Legaria 694, Colonia Irrigación, CP 11500, México, DF (Mexico); CONACYT, México, DF, México (Mexico); Rojas-Trigos, J. B.; Marin, E. [Instituto Politécnico Nacional, Centro de Investigación en Ciencia Aplicada y Tecnología Avanzada, Legaria 694, Colonia Irrigación, CP 11500, México, DF (Mexico); Gandra, F. C. G.; Mansanares, A. M., E-mail: manoel@ifi.unicamp.br [Gleb Wataghin Physics Institute, University of Campinas - Unicamp, 13083-859 Campinas, SP (Brazil)

    2016-07-25

    In this work a combined thermoacoustic and thermoreflectance set-up was designed for imaging biased microelectronic circuits. In particular, it was used with polycrystalline silicon resistive tracks grown on a monocrystalline Si substrate mounted on a test chip. Thermoreflectance images, obtained by scanning a probe laser beam on the sample surface, clearly show the regions periodically heated by Joule effect, which are associated to the electric current distribution in the circuit. The thermoacoustic signal, detected by a pyroelectric/piezoelectric sensor beneath the chip, also discloses the Joule contribution of the whole sample. However, additional information emerges when a non-modulated laser beam is focused on the sample surface in a raster scan mode allowing imaging of the sample. The distribution of this supplementary signal is related to the voltage distribution along the circuit.

  7. Three Phase Two Leg Neutral Point Clamped Converter with output DC Voltage Regulation and Input Power Factor Correction

    Directory of Open Access Journals (Sweden)

    Bogimi Sirisha

    2012-03-01

    Full Text Available In this paper, a three-phase two leg neutral point clamped (NPC converter is presented for power factor correction and dc-link voltage regulation. The adopted converter has simpler circuit configuration and less number of power switches compared to three-level PWM converter. In this circuit configuration, only eight power switches and four clamping diodes with voltage stress of half the dc bus voltage are used. A simplified space vector pulse width modulation scheme (SVPWM is also adopted to track the line current commands. A reference voltage vector is generated on the ac terminal for drawing the sinusoidal line currents with unity power factor. This algorithm reduces the time required to calculate the switching time durations of voltage vectors. The simulation results have been presented to verify the validity and effectiveness of the proposed control strategy.

  8. Controllable Threshold Voltage in Organic Complementary Logic Circuits with an Electron-Trapping Polymer and Photoactive Gate Dielectric Layer.

    Science.gov (United States)

    Dao, Toan Thanh; Sakai, Heisuke; Nguyen, Hai Thanh; Ohkubo, Kei; Fukuzumi, Shunichi; Murata, Hideyuki

    2016-07-20

    We present controllable and reliable complementary organic transistor circuits on a PET substrate using a photoactive dielectric layer of 6-[4'-(N,N-diphenylamino)phenyl]-3-ethoxycarbonylcoumarin (DPA-CM) doped into poly(methyl methacrylate) (PMMA) and an electron-trapping layer of poly(perfluoroalkenyl vinyl ether) (Cytop). Cu was used for a source/drain electrode in both the p-channel and n-channel transistors. The threshold voltage of the transistors and the inverting voltage of the circuits were reversibly controlled over a wide range under a program voltage of less than 10 V and under UV light irradiation. At a program voltage of -2 V, the inverting voltage of the circuits was tuned to be at nearly half of the supply voltage of the circuit. Consequently, an excellent balance between the high and low noise margins (NM) was produced (64% of NMH and 68% of NML), resulting in maximum noise immunity. Furthermore, the programmed circuits showed high stability, such as a retention time of over 10(5) s for the inverter switching voltage. Our findings bring about a flexible, simple way to obtain robust, high-performance organic circuits using a controllable complementary transistor inverter.

  9. Enhanced current and voltage regulators for stand-alone applications

    DEFF Research Database (Denmark)

    Federico, de Bosio; Pastorelli, Michele; Antonio DeSouza Ribeiro, Luiz

    2016-01-01

    State feedback decoupling permits to achieve a better dynamic response for Voltage Source in stand-alone applications. The design of current and voltage regulators is performed in the discrete-time domain since it provides better accuracy and allows direct pole placement. As the attainable...... bandwidth of the current loop is mainly limited by computational and PWM delays, a lead compensator structure is proposed to overcome this limitation. The design of the voltage regulator is based on the Nyquist criterion, verifying to guarantee a high sensitivity peak. Discrete-time domain implementation...

  10. Diagnosis of inverter switch open circuit faults based on neutral point voltage signal analysis

    Directory of Open Access Journals (Sweden)

    Liwei GUO

    Full Text Available Using the current signal to diagnose inverter faults information is apt to be affected by the load, noise and other factors; besides, it requires long diagnosis period with special algorithms and the diagnosis result is easily to be incorrect with no-load or light-load. Focusing on this issue, the logical analysis method is proposed for correlation logical analysis of leg neutral-point voltage and pulse signal to realize the diagnosis of the open circuit faults of inverter switches. The logical expressions of output signals of inverter power tube open-circuit faults is put forward and interrelated hardware circuit design is also elaborated. Delaying the rising edge of inverter power tube's pulse signal can effectively avoid the diagnosis error caused by the power tube's switching on/off. The experiment results show that the method can effectively diagnose the open-circuit faults of single-phase single power tube inverter in real-time and the hardware circuit cost is low, which shows it is effective and feasible.

  11. Flexible low-voltage organic integrated circuits with megahertz switching frequencies (Presentation Recording)

    Science.gov (United States)

    Zschieschang, Ute; Takimiya, Kazuo; Zaki, Tarek; Letzkus, Florian; Richter, Harald; Burghartz, Joachim N.; Klauk, Hagen

    2015-09-01

    A process for the fabrication of integrated circuits based on bottom-gate, top-contact organic thin-film transistors (TFTs) with channel lengths as short as 1 µm on flexible plastic substrates has been developed. In this process, all TFT layers (gate electrodes, organic semiconductors, source/drain contacts) are patterned with the help of high-resolution silicon stencil masks, thus eliminating the need for subtractive patterning and avoiding the exposure of the organic semiconductors to potentially harmful organic solvents or resists. The TFTs employ a low-temperature-processed gate dielectric that is sufficiently thin to allow the TFTs and circuits to operate with voltages of about 3 V. Using the vacuum-deposited small-molecule organic semiconductor 2,9-didecyl-dinaphtho[2,3-b:2',3'-f]thieno[3,2-b]thiophene (C10 DNTT), TFTs with an effective field-effect mobility of 1.2 cm2/Vs, an on/off current ratio of 107, a width-normalized transconductance of 1.2 S/m (with a standard deviation of 6%), and a signal propagation delay (measured in 11-stage ring oscillators) of 420 nsec per stage at a supply voltage of 3 V have been obtained. To our knowledge, this is the first time that megahertz operation has been achieved in flexible organic transistors at supply voltages of less than 10 V. In addition to flexible ring oscillators, we have also demonstrated a 6-bit digital-to-analog converter (DAC) in a binary-weighted current-steering architecture, based on TFTs with a channel length of 4 µm and fabricated on a glass substrate. This DAC has a supply voltage of 3.3 V, a circuit area of 2.6 × 4.6 mm2, and a maximum sampling rate of 100 kS/s.

  12. Global Transient Stability and Voltage Regulation for Multimachine Power Systems

    DEFF Research Database (Denmark)

    Gordon, Mark; Hill, David J.

    2008-01-01

    This paper addresses simultaneously the major fundamental and difficult issues of nonlinearity, uncertainty, dimensionality and globality to derive performance enhancing power system stability control. The main focus is on simultaneous enhancement of transient stability and voltage regulation...... law is implemented to coordinate transient stabilizer and voltage regulator for each machine. Digital simulation studies show that global control scheme achieves unified transient stability and voltage regulation in the presence of parametric uncertainties and significant sudden changes in the network...... of power systems. This problem arises from the practical concern that both frequency and voltage control are important indices of power system control and operation but they are ascribed to different stages of system operation, i.e. the transient and post transient period respectively. The Direct Feedback...

  13. Automatic System for the D.C. High Voltage Qualification of the Superconducting Electrical Circuits of the LHC Machine

    CERN Document Server

    Bozzini, D; Russenschuck, Stephan; Bednarek, M; Jurkiewicz, P; Kotarba, A; Ludwin, J; Olek, S

    2008-01-01

    A d.c. high voltage test system has been developed to verify automatically the insulation resistance of the powering circuits of the LHC. In the most complex case, up to 72 circuits share the same volume inside cryogenic lines. Each circuit can have an insulation fault versus any other circuit or versus ground. The system is able to connect up to 80 circuits and apply a voltage up to 2 kV D.C. The leakage current flowing through each circuit is measured within a range of 1 nA to 1.6 mA. The matrix of measurements allows characterizing the paths taken by the currents and locating weak points of the insulation between circuits. The system is composed of a D.C. voltage source and a data acquisition card. The card is able to measure with precision currents and voltages and to drive up to 5 high voltage switching modules offering 16 channels each. A LabVIEW application controls the system for an automatic and safe operation. This paper describes the hardware and software design, the testing methodology and the res...

  14. Microloss DC Voltage Regulator%微功耗直流稳压器

    Institute of Scientific and Technical Information of China (English)

    郁百超

    2012-01-01

    The voltage interception and voltage compensation was employed to stabilize or regulate DC voltage, whose distinguished characteristic is that the core 'circuit could avoid the electro-magnetic interferences (EMI) to the grid for no use of pulse-width modulation (PWM). Therefore its power consumption is kept as low as possible while its lifetime can be as long as possible with an efficiency as high as 99.5%. Moreover, it is safe and reliable, green and energy-conserving and its simple circuit is easy to fabricate. Its cost, volume, weight, and power consumption are about only ten percent of those of the traditional DC voltage regulators.%微功耗直流稳压器采用电压切割和电压补偿的方法,实现了对直流电压的稳定或调整,该直流稳压器最大特点是,主电路不采用PWM脉宽调制,不产生EMI干扰,因此功耗极小而寿命极长,输出直流电压调整率高,效率高达99.5%,安全可靠,节能环保,电路简单,制作安装容易,其成本、体积、重量、功耗都是传统直流稳压器的十分之一。

  15. An Adaptive Estimation Scheme for Open-Circuit Voltage of Power Lithium-Ion Battery

    Directory of Open Access Journals (Sweden)

    Yun Zhang

    2013-01-01

    Full Text Available Open-circuit voltage (OCV is one of the most important parameters in determining state of charge (SoC of power battery. The direct measurement of it is costly and time consuming. This paper describes an adaptive scheme that can be used to derive OCV of the power battery. The scheme only uses the measurable input (terminal current and the measurable output (terminal voltage signals of the battery system and is simple enough to enable online implement. Firstly an equivalent circuit model is employed to describe the polarization characteristic and the dynamic behavior of the lithium-ion battery; the state-space representation of the electrical performance for the battery is obtained based on the equivalent circuit model. Then the implementation procedure of the adaptive scheme is given; also the asymptotic convergence of the observer error and the boundedness of all the parameter estimates are proven. Finally, experiments are carried out, and the effectiveness of the adaptive estimation scheme is validated by the experimental results.

  16. Simultaneous improvement in short circuit current, open circuit voltage, and fill factor of polymer solar cells through ternary strategy.

    Science.gov (United States)

    An, Qiaoshi; Zhang, Fujun; Li, Lingliang; Wang, Jian; Sun, Qianqian; Zhang, Jian; Tang, Weihua; Deng, Zhenbo

    2015-02-18

    We present a smart strategy to simultaneously increase the short circuit current (Jsc), the open circuit voltage (Voc), and the fill factor (FF) of polymer solar cells (PSCs). A two-dimensional conjugated small molecule photovoltaic material (SMPV1), as the second electron donor, was doped into the blend system of poly(3-hexylthiophene) (P3HT) and [6,6]-phenyl-C71-butyric acid methyl (PC71BM) to form ternary PSCs. The ternary PSCs with 5 wt % SMPV1 doping ratio in donors achieve 4.06% champion power conversion efficiency (PCE), corresponding to about 21.2% enhancement compared with the 3.35% PCE of P3HT:PC71BM-based PSCs. The underlying mechanism on performance improvement of ternary PSCs can be summarized as (i) harvesting more photons in the longer wavelength region to increase Jsc; (ii) obtaining the lower mixed highest occupied molecular orbital (HOMO) energy level by incorporating SMPV1 to increase Voc; (iii) forming the better charge carrier transport channels through the cascade energy level structure and optimizing phase separation of donor/acceptor materials to increase Jsc and FF.

  17. High-Precision Multi-Wave Rectifier Circuit Operating in Low Voltage + 1.5 Volt Current Mode

    Directory of Open Access Journals (Sweden)

    Bancha Burapattanasiri

    2009-12-01

    Full Text Available This article is present high-precision multi-wave rectifier circuit operating in low voltage +/- 1.5 Volt current modes by CMOS technology 0.5 μm, receive input and give output in current mode, respond at high frequency period. The structure compound with high-speed current comparator circuit, current mirror circuit, and CMOS inverter circuit. PSpice program used for confirmation the performance of testing. The PSpice program shows operating of circuit is able to working at maximum input current 400 μAp-p, maximum frequency responding 200 MHz, high precision and low power losses, and non-precision zero crossing output signal.Keywords-component; rectifier circuit; high-precision; low voltage; current mode;

  18. SYNTHESIS OF VOLTAGES OF UNIFORM PWM IN TIME REGULATION

    Directory of Open Access Journals (Sweden)

    A. G. Stryzhniou

    2014-01-01

    Full Text Available The article describes a process of synthesis and qualitative assessment of the harmonic composition of voltages of multiple and single PWM pulses in time regulation, being, along with amplitude, frequency and phase method, one of control methods of an asynchronous motor. The main point of time regulation is that a pause after any two single PWM pulses with different polarity or after any two groups of multiple PWM pulses with different polarity changes during a process of regulation. Feature of time regulation is that a motor has fast response in the range of small-signal of control and good linearity of speed-torque characteristics in the whole control range. Analytical expressions of parameters of PWM pulses ai and ti are obtained which allow to simplify considerably a process of formation and implementation of time regulation using tabular or indexed-tabular methods. These expressions allow not only to define voltage amplitude of  harmonic but also to perform qualitative assessment of harmonic composition of output voltages at time regulation. It is specified that harmonic frequencies wi = w0/q change in inverse proportion to magnitude of parameter q during a process of regulation and there is a replacement of a fundamental frequency by frequencies of higher harmonics.The offered approach allows to synthesize voltage of uniform single and multiple PWM pulses and to perform their comparative and qualitative analysis and the obtained expressions can be used at modeling of AC motor work. Voltage of multiple PWM pulses which is formed using stepped reference voltage with even quantity of steps in a half period and a pause on a zero level has the best parameters by criterion of a minimum of harmonic components and a maximum of a factor of anharmonicity Kнс at time regulation.

  19. Elucidating the interplay between dark current coupling and open circuit voltage in organic photovoltaics

    KAUST Repository

    Erwin, Patrick

    2011-01-01

    A short series of alkyl substituted perylenediimides (PDIs) with varying steric bulk are used to demonstrate the relationship between molecular structure, materials properties, and performance characteristics in organic photovoltaics. Devices were made with the structure indium tin oxide/copper phthalocyanine (200 Å)/PDI (200 Å)/bathocuproine (100 Å)/aluminum (1000 Å). We found that PDIs with larger substituents produced higher open circuit voltages (VOC\\'s) despite the donor acceptor interface gap (Δ EDA) remaining unchanged. Additionally, series resistance was increased simultaneously with VOC the effect of reducing short circuit current, making the addition of steric bulk a tradeoff that needs to be balanced to optimize power conversion efficiency. © 2011 American Institute of Physics.

  20. A SQUID gradiometer module with wire-wound pickup antenna and integrated voltage feedback circuit

    Energy Technology Data Exchange (ETDEWEB)

    Zhang Guofeng [State Key Laboratory of Functional Materials for Informatics, Shanghai Institute of Microsystem and Information Technology (SIMIT), Chinese Academy of Sciences (CAS), Shanghai 200050 (China); Peter Gruenberg Institute (PGI-8), Forschungszentrum Juelich (FZJ), D-52425 Juelich (Germany); Joint Research Laboratory on Superconductivity and Bioelectronics, Collaboration between CAS-Shanghai and FZJ, Shanghai 200050 (China); Graduate University of the Chinese Academy of Sciences, Beijing 100049 (China); Zhang, Yi, E-mail: y.zhang@fz-juelich.de [Peter Gruenberg Institute (PGI-8), Forschungszentrum Juelich (FZJ), D-52425 Juelich (Germany); Joint Research Laboratory on Superconductivity and Bioelectronics, Collaboration between CAS-Shanghai and FZJ, Shanghai 200050 (China); Zhang Shulin [State Key Laboratory of Functional Materials for Informatics, Shanghai Institute of Microsystem and Information Technology (SIMIT), Chinese Academy of Sciences (CAS), Shanghai 200050 (China); Joint Research Laboratory on Superconductivity and Bioelectronics, Collaboration between CAS-Shanghai and FZJ, Shanghai 200050 (China); Krause, Hans-Joachim [Peter Gruenberg Institute (PGI-8), Forschungszentrum Juelich (FZJ), D-52425 Juelich (Germany); Joint Research Laboratory on Superconductivity and Bioelectronics, Collaboration between CAS-Shanghai and FZJ, Shanghai 200050 (China); and others

    2012-10-15

    The performance of the direct readout schemes for dc SQUID, Additional Positive Feedback (APF), noise cancellation (NC) and SQUID bootstrap circuit (SBC), have been studied in conjunction with planar SQUID magnetometers. In this paper, we examine the NC technique applied to a niobium SQUID gradiometer module with an Nb wire-wound antenna connecting to a dual-loop SQUID chip with an integrated voltage feedback circuit for suppression of the preamplifier noise contribution. The sensitivity of the SQUID gradiometer module is measured to be about 1 fT/(cm {radical}Hz) in the white noise range in a magnetically shielded room. Using such gradiometer, both MCG and MEG signals are recorded.

  1. Ultra-Low-Voltage Self-Body Biasing Scheme and Its Application to Basic Arithmetic Circuits

    Directory of Open Access Journals (Sweden)

    Ramiro Taco

    2015-01-01

    Full Text Available The gate level body biasing (GLBB is assessed in the context of ultra-low-voltage logic designs. To this purpose, a GLBB mirror full adder is implemented by using a commercial 45 nm bulk CMOS triple-well technology and compared to equivalent conventional zero body-biased CMOS and dynamic threshold voltage MOSFET (DTMOS circuits under different running conditions. Postlayout simulations demonstrate that, at the parity of leakage power consumption, the GLBB technique exhibits a significant concurrent reduction of the energy per operation and the delay in comparison to the conventional CMOS and DTMOS approaches. The silicon area required by the GLBB full adder is halved with respect to the equivalent DTMOS implementation, but it is higher in comparison to conventional CMOS design. Performed analysis also proves that the GLBB solution exhibits a high level of robustness against temperature fluctuations and process variations.

  2. High Open-Circuit Voltage Solar Cells Based on Organic-Inorganic Lead Bromide Perovskite.

    Science.gov (United States)

    Edri, Eran; Kirmayer, Saar; Cahen, David; Hodes, Gary

    2013-03-21

    Mesoscopic solar cells, based on solution-processed organic-inorganic perovskite absorbers, are a promising avenue for converting solar to electrical energy. We used solution-processed organic-inorganic lead halide perovskite absorbers, in conjunction with organic hole conductors, to form high voltage solar cells. There is a dire need for low-cost cells of this type, to drive electrochemical reactions or as the high photon energy cell in a system with spectral splitting. These perovskite materials, although spin-coated from solution, form highly crystalline materials. Their simple synthesis, along with high chemical versatility, allows tuning their electronic and optical properties. By judicious selection of the perovskite lead halide-based absorber, matching organic hole conductor, and contacts, a cell with a ∼ 1.3 V open circuit voltage was made. While further study is needed, this achievement provides a general guideline for additional improvement of cell performance.

  3. Surge protective device response to steep front transient in low voltage circuit

    Energy Technology Data Exchange (ETDEWEB)

    Marcuz, J.; Binczak, S.; Bilbault, J.M. [Universite de Bourgogne, Dijon (France)], Emails: jerome.marcuz@ laposte.net, stbinc@u-bourgogne.fr, bilbault@u-bourgogne.fr; Girard, F. [ADEE Electronic, Pont de Pany (France)

    2007-07-01

    Surge propagation on cables of electrical or data lines leads to a major protection problem as the number of equipment based on solid-state circuits or microprocessors increases. Sub-microsecond components of real surge waveform has to be taken into account for a proper protection even in the case of surges caused by indirect lightning effects. The response of a model of transient voltage suppressor diode based surge protection device (SPD) to fast front transient is analytically studied, then compared to simulations, including the lines connected to the SPD and to the protected equipment. (author)

  4. Voltage Recovery of Grid-Connected Wind Turbines with DFIG After a Short-Circuit Fault

    DEFF Research Database (Denmark)

    Sun, Tao; Chen, Zhe; Blaabjerg, Frede

    2004-01-01

    recovery of variable speed wind turbines with doubly fed induction generators (DFIG). A simulation model of a MW-level variable speed wind turbine with a DFIG developed in PSCAD/EMTDC is presented, and the control and protection schemes are described. A new control strategy is proposed to re......-establish the wind turbine terminal voltage after the clearance of an external short-circuit fault, and the restore the normal operation of the variable speed wind turbine with DFIG, which has been demonstrated by simulation results....

  5. Optical fiber imaging for high speed plasma motion diagnostics: applied to low voltage circuit breakers.

    Science.gov (United States)

    McBride, J W; Balestrero, A; Ghezzi, L; Tribulato, G; Cross, K J

    2010-05-01

    An integrated portable measurement system is described for the study of high speed and high temperature unsteady plasma flows such as those found in the vicinity of high current switching arcs. An array of optical fibers allows the formation of low spatial resolution images, with a maximum capture rate of 1 x 10(6) images per second (1 MHz), with 8 bit intensity resolution. Novel software techniques are reported to allow imaging of the arc; and to measure arc trajectories. Results are presented on high current (2 kA) discharge events in a model test fixture and on the application to a commercial low voltage circuit breaker.

  6. Effect of recombination on the open-circuit voltage of a silicon solar cell

    Science.gov (United States)

    Von Roos, O.; Landsberg, P. T.

    1985-01-01

    A theoretical study of the influence of band-band Auger, band-trap Auger, and the ordinary Shockley-Read-Hall mechanism for carrier recombination on the open-circuit voltage VOC of a solar cell is presented. Under reasonable assumptions for the magnitude of rate constants and realistic values for trap densities, surface recombination velocities and band-gap narrowing, the maximum VOC for typical back surface field solar cells is found to lie in the range between 0.61 and 0.72 V independent of base width.

  7. Carbon nanotube-polybithiophene photovoltaic devices with high open-circuit voltage

    Energy Technology Data Exchange (ETDEWEB)

    Patyk, Rodolfo L.; Huemmelgen, Ivo A. [Departamento de Fisica, Universidade Federal do Parana, Caixa Postal 19044, 81531-990 Curitiba PR (Brazil); Lomba, Bruno S.; Nogueira, Ana Flavia [Laboratorio de Nanotechnologia e Energia Solar, Instituto de Quimica, Unicamp, C.P. 6154, 13084-971 Campinas, Sao Paulo (Brazil); Furtado, Clascidia A.; Santos, Adelina Pinheiro [Laboratorio de Quimica de Nanoestruturas, CDTN/CNEN, Belo Horizonte, MG (Brazil); Mello, Regina M.Q.; Micaroni, Liliana [Departamento de Quimica, Universidade Federal do Parana, Caixa Postal 19081, 81531-990 Curitiba PR (Brazil)

    2007-01-15

    We report the preparation of photovoltaic devices using modified single wall carbon nanotubes, SWNTs. Devices are produced stacking on top of fluorine-doped tin-oxide, an electrochemically deposited polybithiophene layer, a layer of SWNT blended with poly(3-octylthiophene) and an evaporated top metal contact, Ca/Al or Al. Ca/Al-top-electrode devices achieve open-circuit voltages of 1.81 V and average power conversion efficiency of 1.48% at irradiance of 15.5 W m{sup -2}, spectrally distributed following AM1.5. (copyright 2007 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

  8. Numerical Electric Field Analysis of Power Status Sensor Observing Power Distribution System Taking into Account Voltage Divider Measurement Circuit

    Science.gov (United States)

    Kubo, Takuro; Furukawa, Tatsuya; Itoh, Hideaki; Fukumoto, Hisao; Wakuya, Hiroshi; Ohchi, Masashi

    We have proposed and preproducted the voltage-current waveform sensor of resin molded type for measuring the power factor and harmonics in power distribution systems. We have executed numerical electromagnetic analyses using the finite element method to estimate the characteristics and behaviours of the sensor. Although the magnetic field analyses for the current sensor have involved the measurement circuit, the electric field analyses have not included the measurement circuit for measuring voltage waveforms of power lines. In this paper, we describe the electric field analyses with the measurement circuit and prove the insulating strength of the proposed sensor permissible to the use in 22kV power distribution systems.

  9. Testing to Investigate Stress-LifetimeCharacteristics of High Voltage Printed Circuit Boards

    Science.gov (United States)

    El Korashy, Oliver; Franke, Andreas; Gollor, Matthias

    2014-08-01

    Printed circuit boards (PCBs) are typically used in all electronic equipment, including those conditioning or controlling high voltage (HV) for space satellite applications. With the use of new subsystems that require higher voltages (generally several hundred volts up to tens of kV), stress-lifetime issues are becoming more complex. In order to allow compact design and cost efficient production of HV modules, there is an increasing demand to improve the design of PCBs with encapsulation or conformal coating at higher voltages.Within a PCB there are a number of electrical field interfaces each of which can have individual stress- lifetime characteristics, and the influence of environmental aging should also be considered, which means a large number of sample types should be tested to gain experimental evidence to define the margin for each interface. This paper demonstrates a method to test multiple samples at a fixed DC voltage stress until the event of a breakdown, and presents test results from 6 single-sided encapsulated PCB samples.

  10. Investigation of phase-wise voltage regulator control logics for compensating voltage deviations in an experimental low voltage network

    DEFF Research Database (Denmark)

    Hu, Junjie; Zecchino, Antonio; Marinelli, Mattia

    2016-01-01

    either locally or remotely. To evaluate and compare the control performances of the three control logics, all the tests use the same loading profiles. The experimental results indicate that the modified line compensation control can regulate voltage in a safe band in the case of various load......This paper investigates the control logics of an on-load tap-changer (OLTC) transformer by means of an experimental system validation. The experimental low-voltage unbalanced system consists of a decoupled single-phase OLTC transformer, a 75-metre 16 mm2 cable, a controllable single-phase resistive...... load and an electric vehicle, which has the vehicle-to-grid function. Three control logics of the OLTC transformer are described in the study. The three control logics are classified based on their control objectives and control inputs, which include network currents and voltages, and can be measured...

  11. Robust and Energy-Efficient Ultra-Low-Voltage Circuit Design under Timing Constraints in 65/45 nm CMOS

    Directory of Open Access Journals (Sweden)

    David Bol

    2011-01-01

    Full Text Available Ultra-low-voltage operation improves energy efficiency of logic circuits by a factor of 10×, at the expense of speed, which is acceptable for applications with low-to-medium performance requirements such as RFID, biomedical devices and wireless sensors. However, in 65/45 nm CMOS, variability and short-channel effects significantly harm robustness and timing closure of ultra-low-voltage circuits by reducing noise margins and jeopardizing gate delays. The consequent guardband on the supply voltage to meet a reasonable manufacturing yield potentially ruins energy efficiency. Moreover, high leakage currents in these technologies degrade energy efficiency in case of long stand-by periods. In this paper, we review recently published techniques to design robust and energy-efficient ultra-low-voltage circuits in 65/45 nm CMOS under relaxed yet strict timing constraints.

  12. Fractional-order Systems and Synchronous Generator Voltage Regulator

    OpenAIRE

    2015-01-01

    Modern regulators of synchronous generators, including voltage regulators, are digital systems, in their vast majority with standard structures contained in the IEEE standard. These are systems described with stationary differential equations of integral order. Differential equations of fractional order are not employed in regulators for synchronous generator control. This paper presents an analysis of the possibilities of using a system of fractional differential equations in the volta...

  13. Developmental regulation of spatio-temporal patterns of cortical circuit activation

    Directory of Open Access Journals (Sweden)

    Trevor Charles Griffen

    2013-01-01

    Full Text Available Neural circuits are refined in an experience-dependent manner during early postnatal development. How development modulates the spatio-temporal propagation of activity through cortical circuits is poorly understood. Here we use voltage sensitive dye imaging (VSD to show that there are significant changes in the spatio-temporal patterns of intracortical signals in primary visual cortex from postnatal day 13 (P13, eye opening, to P28, the peak of the critical period for rodent visual cortical plasticity. Upon direct stimulation of layer 4 (L4, activity spreads to L2/3 and to L5 at all ages. However, while from eye opening to the peak of the critical period, the amplitude and persistence of the voltage signal decrease, peak activation is reached more quickly and the interlaminar gain increases with age. The lateral spread of activation within layers remains unchanged throughout the time window under analysis. These developmental changes in spatio-temporal patterns of intracortical circuit activation are mediated by differences in the contributions of excitatory and inhibitory synaptic components. Our results demonstrate that after eye opening the circuit in primary visual cortex is refined through a progression of changes that shape the spatio-temporal patterns of circuit activation. Signals become more efficiently propagated across layers through developmentally regulated changes in interlaminar gain.

  14. Controlled Conjugated Backbone Twisting for an Increased Open-Circuit Voltage while Having a High Short-Circuit Current in Poly(hexylthiophene) Derivatives

    KAUST Repository

    Ko, Sangwon

    2012-03-21

    Conjugated polymers with nearly planar backbones have been the most commonly investigated materials for organic-based electronic devices. More twisted polymer backbones have been shown to achieve larger open-circuit voltages in solar cells, though with decreased short-circuit current densities. We systematically impose twists within a family of poly(hexylthiophene)s and examine their influence on the performance of polymer:fullerene bulk heterojunction (BHJ) solar cells. A simple chemical modification concerning the number and placement of alkyl side chains along the conjugated backbone is used to control the degree of backbone twisting. Density functional theory calculations were carried out on a series of oligothiophene structures to provide insights on how the sterically induced twisting influences the geometric, electronic, and optical properties. Grazing incidence X-ray scattering measurements were performed to investigate how the thin-film packing structure was affected. The open-circuit voltage and charge-transfer state energy of the polymer:fullerene BHJ solar cells increased substantially with the degree of twist induced within the conjugated backbone-due to an increase in the polymer ionization potential-while the short-circuit current decreased as a result of a larger optical gap and lower hole mobility. A controlled, moderate degree of twist along the poly(3,4-dihexyl-2,2′:5′,2′′- terthiophene) (PDHTT) conjugated backbone led to a 19% enhancement in the open-circuit voltage (0.735 V) vs poly(3-hexylthiophene)-based devices, while similar short-circuit current densities, fill factors, and hole-carrier mobilities were maintained. These factors resulted in a power conversion efficiency of 4.2% for a PDHTT:[6,6]-phenyl-C 71-butyric acid methyl ester (PC 71BM) blend solar cell without thermal annealing. This simple approach reveals a molecular design avenue to increase open-circuit voltage while retaining the short-circuit current. © 2012 American

  15. Reduced voltage losses yield 10% efficient fullerene free organic solar cells with >1 V open circuit voltages

    KAUST Repository

    Baran, D.

    2016-11-09

    Optimization of the energy levels at the donor-acceptor interface of organic solar cells has driven their efficiencies to above 10%. However, further improvements towards efficiencies comparable with inorganic solar cells remain challenging because of high recombination losses, which empirically limit the open-circuit voltage (Voc) to typically less than 1 V. Here we show that this empirical limit can be overcome using non-fullerene acceptors blended with the low band gap polymer PffBT4T-2DT leading to efficiencies approaching 10% (9.95%). We achieve Voc up to 1.12 V, which corresponds to a loss of only Eg/q - Voc = 0.5 ± 0.01 V between the optical bandgap Eg of the polymer and Voc. This high Voc is shown to be associated with the achievement of remarkably low non-geminate and non-radiative recombination losses in these devices. Suppression of non-radiative recombination implies high external electroluminescence quantum efficiencies which are orders of magnitude higher than those of equivalent devices employing fullerene acceptors. Using the balance between reduced recombination losses and good photocurrent generation efficiencies achieved experimentally as a baseline for simulations of the efficiency potential of organic solar cells, we estimate that efficiencies of up to 20% are achievable if band gaps and fill factors are further optimized. © The Royal Society of Chemistry 2016.

  16. Reduced voltage losses yield 10% efficient fullerene free organic solar cells with >1 V open circuit voltages.

    Science.gov (United States)

    Baran, D; Kirchartz, T; Wheeler, S; Dimitrov, S; Abdelsamie, M; Gorman, J; Ashraf, R S; Holliday, S; Wadsworth, A; Gasparini, N; Kaienburg, P; Yan, H; Amassian, A; Brabec, C J; Durrant, J R; McCulloch, I

    2016-12-01

    Optimization of the energy levels at the donor-acceptor interface of organic solar cells has driven their efficiencies to above 10%. However, further improvements towards efficiencies comparable with inorganic solar cells remain challenging because of high recombination losses, which empirically limit the open-circuit voltage (Voc) to typically less than 1 V. Here we show that this empirical limit can be overcome using non-fullerene acceptors blended with the low band gap polymer PffBT4T-2DT leading to efficiencies approaching 10% (9.95%). We achieve Voc up to 1.12 V, which corresponds to a loss of only Eg/q - Voc = 0.5 ± 0.01 V between the optical bandgap Eg of the polymer and Voc. This high Voc is shown to be associated with the achievement of remarkably low non-geminate and non-radiative recombination losses in these devices. Suppression of non-radiative recombination implies high external electroluminescence quantum efficiencies which are orders of magnitude higher than those of equivalent devices employing fullerene acceptors. Using the balance between reduced recombination losses and good photocurrent generation efficiencies achieved experimentally as a baseline for simulations of the efficiency potential of organic solar cells, we estimate that efficiencies of up to 20% are achievable if band gaps and fill factors are further optimized.

  17. Enhanced Open-Circuit Voltage of PbS Nanocrystal Quantum Dot Solar Cells

    Science.gov (United States)

    Yoon, Woojun; Boercker, Janice E.; Lumb, Matthew P.; Placencia, Diogenes; Foos, Edward E.; Tischler, Joseph G.

    2013-07-01

    Nanocrystal quantum dots (QD) show great promise toward improving solar cell efficiencies through the use of quantum confinement to tune absorbance across the solar spectrum and enable multi-exciton generation. Despite this remarkable potential for high photocurrent generation, the achievable open-circuit voltage (Voc) is fundamentally limited due to non-radiative recombination processes in QD solar cells. Here we report the highest open-circuit voltages to date for colloidal QD based solar cells under one sun illumination. This Voc of 692 +/- 7 mV for 1.4 eV PbS QDs is a result of improved passivation of the defective QD surface, demonstrating as a function of the QD bandgap (Eg). Comparing experimental Voc variation with the theoretical upper-limit obtained from one diode modeling of the cells with different Eg, these results clearly demonstrate that there is a tremendous opportunity for improvement of Voc to values greater than 1 V by using smaller QDs in QD solar cells.

  18. Digital-circuit analysis of short-gate tunnel FETs for low-voltage applications

    Science.gov (United States)

    Zhuge, Jing; Verhulst, Anne S.; Vandenberghe, William G.; Dehaene, Wim; Huang, Ru; Wang, Yangyuan; Groeseneken, Guido

    2011-08-01

    This paper investigates the potential of tunnel field-effect transistors (TFETs), with emphasis on short-gate TFETs, by simulation for low-power digital applications having a supply voltage lower than 0.5 V. A transient study shows that the tunneling current has a negligible contribution in charging and discharging the gate capacitance of TFETs. In spite of a higher resistance region in the short-gate TFET, the gate (dis)charging speed still meets low-voltage application requirements. A circuit analysis is performed on short-gate TFETs with different materials, such as Si, Ge and heterostructures in terms of voltage overshoot, delay, static power, energy consumption and energy delay product (EDP). These results are compared to MOSFET and full-gate TFET performance. It is concluded that short-gate heterostructure TFETs (Ge-source for nTFET, In0.6Ga0.4As-source for pTFET) are promising candidates to extend the supply voltage to lower than 0.5 V because they combine the advantage of a low Miller capacitance, due to the short-gate structures, and strong drive current in TFETs, due to the narrow bandgap material in the source. At a supply voltage of 0.4 V and for an EOT and channel length of 0.6 nm and 40 nm, respectively, a three-stage inverter chain based on short-gate heterostructure TFETs saves 40% energy consumption per cycle at the same delay and shows 60%-75% improvement of EDP at the same static power, compared to its full-gate counterpart. When compared to the MOSFET, better EDP can be achieved in the heterostructure TFET especially at low static power consumption.

  19. Numerical modeling of high-voltage circuit breaker arcs and their interraction with the power system

    Science.gov (United States)

    Orama, Lionel R.

    In this work the interaction between series connected gas and vacuum circuit breaker arcs has been studied. The breakdown phenomena in vacuum interrupters during the post arc current period have been of special interest. Numerical models of gas and vacuum arcs were developed in the form of black box models. Especially, the vacuum post arc model was implemented by combining the existing transition model with an ion density function and expressions for the breakdown mechanisms. The test series studied reflect that for electric fields on the order of 10sp7V/m over the anode, the breakdown of the vacuum gap can result from a combination of both thermal and electrical stresses. For a particular vacuum device, the vacuum model helps to find the interruption limits of the electric field and power density over the anode. The series connection of gas and vacuum interrupters always performs better than the single gas device. Moreover, to take advantage of the good characteristics of both devices, the time between the current zero crossing in each interrupter can be changed. This current zero synchronization is controlled by changing the capacitance in parallel to the gas device. This gas/vacuum interrupter is suitable for interruption of very stressful short circuits in which the product of the dI/dt before current zero and the dV/dt after current zero is very high. Also, a single SF6 interrupter can be replaced by an air circuit breaker of the same voltage rating in series with a vacuum device without compromising the good performance of the SF6 device. Conceptually, a series connected vacuum device can be used for high voltage applications with equal distribution of electrical stresses between the individual interrupters. The equalization can be made by a sequential opening of the individual contact pairs, beginning with the interruptors that are closer to ground potential. This could eliminate the use of grading capacitors.

  20. Simple voltage-controlled current source for wideband electrical bioimpedance spectroscopy: circuit dependences and limitations

    Science.gov (United States)

    Seoane, F.; Macías, R.; Bragós, R.; Lindecrantz, K.

    2011-11-01

    In this work, the single Op-Amp with load-in-the-loop topology as a current source is revisited. This circuit topology was already used as a voltage-controlled current source (VCCS) in the 1960s but was left unused when the requirements for higher frequency arose among the applications of electrical bioimpedance (EBI). The aim of the authors is not only limited to show that with the currently available electronic devices it is perfectly viable to use this simple VCCS topology as a working current source for wideband spectroscopy applications of EBI, but also to identify the limitations and the role of each of the circuit components in the most important parameter of a current for wideband applications: the output impedance. The study includes the eventual presence of a stray capacitance and also an original enhancement, driving with current the VCCS. Based on the theoretical analysis and experimental measurements, an accurate model of the output impedance is provided, explaining the role of the main constitutive elements of the circuit in the source's output impedance. Using the topologies presented in this work and the proposed model, any electronic designer can easily implement a simple and efficient current source for wideband EBI spectroscopy applications, e.g. in this study, values above 150 kΩ at 1 MHz have been obtained, which to the knowledge of the authors are the largest values experimentally measured and reported for a current source in EBI at this frequency.

  1. Modeling and Simulation of Flexible Transmission Mechanism with Multiclearance Joints for Ultrahigh Voltage Circuit Breakers

    Directory of Open Access Journals (Sweden)

    Fangang Meng

    2015-01-01

    Full Text Available The transmission mechanism, of which the dynamic characteristics determine the reliability of the circuit breaker, is the principal component of the ultrahigh voltage (UHV circuit breaker. The characteristics of transmission mechanism are quick motion, high sensibility, and high reliability. The transmission mechanism with multiclearance joints present strong no-linear vibration feature which strongly affects the reliability of the UHV circuit breaker. In this investigation, a planar rigid-flexible coupling model of the transmission mechanism considering the clearance joints and the flexibility of components is established by using ADAMS software. The dynamic contact model in clearance joints is performed, based on clearance vector model of clearance joint. Then, the reliability of the model is proved by means of comparing the results of experiments. The simulation results show that the dynamic response of the mechanism is greatly influenced by the clearance and the flexibility of components has a role of suspension for the mechanism. Moreover, the influence of the clearance size, input speed, and number of clearance joints on the dynamic characteristics of the mechanism are also investigated.

  2. Factors limiting the open-circuit voltage in microcrystalline silicon solar cells

    Directory of Open Access Journals (Sweden)

    Chatterjee P.

    2011-11-01

    Full Text Available In studying photovoltaic devices made with silicon thin films and considering them according to their grain size, it is curious that as the crystalline fraction increases, the open-circuit voltage (Voc – rather than approaching that of the single-crystal case – shows a decline. To gain an insight into this behavior, observed in hydrogenated microcrystalline silicon (μc-Si:H solar cells prepared under a variety of deposition conditions, we have used a detailed electrical-optical computer modeling program, ASDMP. Two typical μc-Si:H cells with low (~79% and higher (~93% crystalline volume fractions (Fc, deposited in our laboratory and showing this general trend, were modeled. From the parameters extracted by simulation of their experimental current density – voltage and quantum efficiency characteristics, it was inferred that the higher Fc cell has both a higher band gap defect density as well as a lower band gap energy. Our calculations reveal that the proximity of the quasi-Fermi levels to the energy bands in cells based on highly crystallized μc-Si:H (assumed to have a lower band gap, results in both higher free and trapped carrier densities. The trapped hole population, that is particularly high near the P/I interface, results in a strong interface field, a collapse of the field in the volume, and hence a lower open-circuit voltage. Interestingly enough, we were able to fabricate fluorinated μc-Si:H:F cells having 100% crystalline fraction as well as very large grains, that violate the general trend and show a higher Voc. Modeling indicates that this is possible for the latter case, as also for a crystalline silicon PN cell, in spite of a sharply reduced band gap, because the lower effective density of states at the band edges and a sharply reduced gap defect density overcome the effect of the lower band gap.

  3. Development of High-Voltage Vacuum Circuit Breaker%高电压真空断路器的发展

    Institute of Scientific and Technical Information of China (English)

    吴红亚; 李建基

    2011-01-01

    六氟化硫断路器在高压断路器中居主导地位,而真空断路器在中压领域占绝对优势,并在高电压领域崭露头角。阐述了开发高电压真空断路器的必要性,介绍了现有产品的结构与特点,并提出了研发高电压真空断路器需解决的技术问题及相关的应对措施。%Sulfur hexafluoride circuit breakers take a leading position in high-voltage circuit breakers and vacuum circuit breakers hold all the trumps in medium voltage field,making a figure in high-voltage field.Description was made to the necessity of development of high-voltage vacuum circuit breakers.Introduction was made to structure and features of the existing products.This paper raised technical issues to be solved in RD of high-voltage vacuum circuit breakers and their related countermeasures.

  4. Real-Time Nanoscale Open-Circuit Voltage Dynamics of Perovskite Solar Cells.

    Science.gov (United States)

    Garrett, Joseph L; Tennyson, Elizabeth M; Hu, Miao; Huang, Jinsong; Munday, Jeremy N; Leite, Marina S

    2017-04-12

    Hybrid organic-inorganic perovskites based on methylammonium lead (MAPbI3) are an emerging material with great potential for high-performance and low-cost photovoltaics. However, for perovskites to become a competitive and reliable solar cell technology their instability and spatial variation must be understood and controlled. While the macroscopic characterization of the devices as a function of time is very informative, a nanoscale identification of their real-time local optoelectronic response is still missing. Here, we implement a four-dimensional imaging method through illuminated heterodyne Kelvin probe force microscopy to spatially (perovskite solar cells in a low relative humidity environment. Local open-circuit voltage (Voc) images show nanoscale sites with voltage variation >300 mV under 1-sun illumination. Surprisingly, regions of voltage that relax in seconds and after several minutes consistently coexist. Time-dependent changes of the local Voc are likely due to intragrain ion migration and are reversible at low injection level. These results show for the first time the real-time transient behavior of the Voc in perovskite solar cells at the nanoscale. Understanding and controlling the light-induced electrical changes that affect device performance are critical to the further development of stable perovskite-based solar technologies.

  5. A 5 V-to-3.3 V CMOS Linear Regulator with Three-Output Temperature-Independent Reference Voltages

    Directory of Open Access Journals (Sweden)

    San-Fu Wang

    2016-01-01

    Full Text Available This paper presents a 5 V-to-3.3 V linear regulator circuit, which uses 3.3 V CMOS transistors to replace the 5 V CMOS transistors. Thus, the complexity of the manufacturing semiconductor process can be improved. The proposed linear regulator is implemented by cascode architecture, which requires three different reference voltages as the bias voltages of its circuit. Thus, the three-output temperature-independent reference voltage circuit is proposed, which provides three accurate reference voltages simultaneously. The three-output temperature-independent reference voltages also can be used in other circuits of the chip. By using the proposed temperature-independent reference voltages, the proposed linear regulator can provide an accurate output voltage, and it is suitable for low cost, small size, and highly integrated system-on-chip (SoC applications. Moreover, the proposed linear regulator uses the cascode technique, which improves both the gain performance and the isolation performance. Therefore, the proposed linear regulator has a good performance in reference voltage to output voltage isolation. The voltage variation of the linear regulator is less than 2.153% in the temperature range of −40°C–120°C, and the power supply rejection ratio (PSRR is less than −42.8 dB at 60 Hz. The regulator can support 0~200 mA output current. The core area is less than 0.16 mm2.

  6. Low input voltage converter/regulator minimizes external disturbances

    Science.gov (United States)

    1966-01-01

    Low-input voltage converter/regulator constructed in a coaxial configuration minimizes external magnetic field disturbance, suppresses radio noise interference, and provides excellent heat transfer from power transistors. It converts the output of fuel and solar cells, thermionic diodes, thermoelectric generators, and electrochemical batteries to a 28 V dc output.

  7. Circuits Regulating Pleasure and Happiness-Mechanisms of Depression

    NARCIS (Netherlands)

    Loonen, Antonius; Ivanova, Svetlana A

    2016-01-01

    According to our model of the regulation of appetitive-searching vs. distress-avoiding behaviors, the motivation to display these essential conducts is regulated by two parallel cortico-striato-thalamo-cortical, re-entry circuits, including the core and the shell parts of the nucleus accumbens,

  8. Circuits Regulating Pleasure and Happiness-Mechanisms of Depression

    NARCIS (Netherlands)

    Loonen, Antonius; Ivanova, Svetlana A

    2016-01-01

    According to our model of the regulation of appetitive-searching vs. distress-avoiding behaviors, the motivation to display these essential conducts is regulated by two parallel cortico-striato-thalamo-cortical, re-entry circuits, including the core and the shell parts of the nucleus accumbens, resp

  9. Open-circuit voltage analysis of p-i-n type amorphous silicon solar cells deposited at low temperature

    Institute of Scientific and Technical Information of China (English)

    Ni Jian; Zhang Jian-Jun; Cao Yu; Wang Xian-Bao; Li Chao; Chen Xin-Liang; Geng Xin-Hua; Zhao Ying

    2011-01-01

    This paper identifies the contributions of p-a-SiC:H layers and i-a-Si:H layers to the open circuit voltage of p-i-n type a-Si:H solar cells deposited at a low temperature of 125 ℃.We find that poor quality p-a-SiC:H films under regular conditions lead to a restriction of open circuit voltage although the band gap of the i-layer varies widely.A significant improvement in open circuit voltage has been obtained by using high quality p-a-SiC:H films optimized at the "low-power regime" under low silane flow rates and high hydrogen dilution conditions.

  10. Surface-charge accumulation effects on open-circuit voltage in organic solar cells based on photoinduced impedance analysis.

    Science.gov (United States)

    Zang, Huidong; Hsiao, Yu-Che; Hu, Bin

    2014-03-14

    The accumulation of dissociated charge carriers plays an important role in reducing the loss occurring in organic solar cells. We find from light-assisted capacitance measurements that the charge accumulation inevitably occurred at the electrode and photovoltaic layer interface for bulk-heterojunction ITO/PEDOT:PSS/P3HT:PCBM/Ca/Al solar cells. Our results indicate, for the first time through impedance measurements, that the charge accumulation exists at the anode side of the device, and more importantly, we successfully identify the type of charge accumulated. Further study shows that the charge accumulation can significantly affect open circuit voltage and short circuit current. As a result, our experimental results from light assisted capacitance measurements provide a new understanding of the loss in open-circuit voltage and short-circuit photocurrent based on charge accumulation. Clearly, controlling charge accumulation presents a new mechanism to improve the photovoltaic performance of organic solar cells.

  11. Discussion on Selectivity of Low Voltage Circuit Breakers%低压断路器的选择性探讨

    Institute of Scientific and Technical Information of China (English)

    何国标

    2014-01-01

    This paper introduces the principle of selectivity for low voltage circuit breakers in distribution line. Focus on the coordinate of several circuit breakers and selectivity of overload and short circuit. This paper describes the latest selectivity technology of low voltage circuit breakers at home and abroad.%本文介绍了在配电线路中对不同低压断路器进行选择的原则。着重阐述了几种断路器之间的配合,过载情况、短路情况下的选择性。并阐述了国内外现阶段最新的低压断路器的选择性技术。

  12. A Smart Load Interface and Voltage Regulator for Electrostatic Vibration Energy Harvester

    Science.gov (United States)

    Bedier, Mohammed; Basset, Philippe; Galayko, Dimitri

    2016-11-01

    This paper presents a new implementation in ams 0.35μm HV technology of a complete energy management system for an electrostatic vibrational energy harvester (e-VEH). It is based on the Bennet's doubler architecture and includes a load voltage regulator (LVR) and a smart Load Interface (LI) that are self-controlled with internal voltages for maximum power point tracking (MMPT). The CMOS implementation makes use of an energy harvester that is capable of producing up to 1.8μW at harmonic excitation, given its internal voltage is kept within its optimum. An intermediate LI stage and its controller makes use of a high side switch with zero static power level shifter, and a low power hysteresis comparator. A full circuit level simulation with a VHDL-AMS model of the e-VEH presented was successfully achieved, indicating that the proposed load interface controller consumes less than 100nW average power. Moreover, a LVR regulates the buffer and discharge the harvested energy into a generic resistive load maintaining the voltage within a nominal value of 2 Volts.

  13. The correlation of open-circuit voltage with bandgap in amorphous silicon-based pin solar cells

    Science.gov (United States)

    Crandall, R. S.; Schiff, E. A.

    1996-01-01

    We briefly review the correlation of open-circuit voltages VOC with the bandgap of the intrinsic layer in amorphous silicon based pin solar cells. We discuss two mechanisms which limit VOC: intrinsic layer recombination, and the built-in potential VBI. In particular we discuss Li's proposal that the open-circuit voltages in higher bandgap cells (EG>1.9 eV) are VBI-limited. Based on computer simulations of pin solar cells we propose that VBI limitation occurs when the recombination limit to VOC exceeds the cell's field-reversal voltage VR. For a-Si:H based cells this field-reversal voltage occurs at about VBI-0.3 V. This proposal would account for the observation that VBI limitation occurs for VOC significantly smaller than VBI.

  14. Voltage sags due to the short-circuits on transmission lines; Afundamentos de tensao provocados por curto-circuitos em linhas de transmissao

    Energy Technology Data Exchange (ETDEWEB)

    Klock Junior, Odemar Solano [Companhia Paranaense de Energia (COPEL), Curitiba, PR (Brazil)

    2001-07-01

    This paper analyses the voltage sags influence on the buses, including the ones where consumers of the COPEL transmission electric system, determining the sags number and the approximate values for short-circuits on transmission lines. The voltage values, during the the short-circuit regime are obtained from the data for the short-circuit program. The short-circuits are simulated by the assembly of the electric system impedance matrix, from where the voltage values for short-circuits on any point of the electric system can be determined using simply calculations.

  15. Correlation between the Open-Circuit Voltage and Charge Transfer State Energy in Organic Photovoltaic Cells.

    Science.gov (United States)

    Zou, Yunlong; Holmes, Russell J

    2015-08-26

    In order to further improve the performance of organic photovoltaic cells (OPVs), it is essential to better understand the factors that limit the open-circuit voltage (VOC). Previous work has sought to correlate the value of VOC in donor-acceptor (D-A) OPVs to the interface energy level offset (EDA). In this work, measurements of electroluminescence are used to extract the charge transfer (CT) state energy for multiple small molecule D-A pairings. The CT state as measured from electroluminescence is found to show better correlation to the maximum VOC than EDA. The difference between EDA and the CT state energy is attributed to the Coulombic binding energy of the CT state. This correlation is demonstrated explicitly by inserting an insulating spacer layer between the donor and acceptor materials, reducing the binding energy of the CT state and increasing the measured VOC. These results demonstrate a direct correlation between maximum VOC and CT state energy.

  16. CMOS circuits for electromagnetic vibration transducers interfaces for ultra-low voltage energy harvesting

    CERN Document Server

    Maurath, Dominic

    2015-01-01

    Chip-integrated power management solutions are a must for ultra-low power systems. This enables not only the optimization of innovative sensor applications. It is also essential for integration and miniaturization of energy harvesting supply strategies of portable and autonomous monitoring systems. The book particularly addresses interfaces for energy harvesting, which are the key element to connect micro transducers to energy storage elements. Main features of the book are: - A comprehensive technology and application review, basics on transducer mechanics, fundamental circuit and control design, prototyping and testing, up to sensor system supply and applications. - Novel interfacing concepts - including active rectifiers, MPPT methods for efficient tracking of DC as well as AC sources, and a fully-integrated charge pump for efficient maximum AC power tracking at sub-100µW ultra-low power levels. The chips achieve one of widest presented operational voltage range in standard CMOS technology: 0.44V to over...

  17. The use of radial integrated circuits for the design of voltage-controlled oscillators

    Science.gov (United States)

    de Jaeger, M.

    A theoretical model for the behavior of voltage-controlled oscillators (VCO) used in millimeter-wave applications is presented, with attention concentrated on multi-diode structures. A radial structure is considered, featuring the VCOs operating in the Q band with ICs. The model developed examines the electromagnetic behavior of the circuit, taking into account multimodal functioning. Experimental results are presented for the frequency evolution with impedance. The design of a VCO, through integration of a Gunn diode and a varactor into a radial system, is described, including an analysis of the series resistance of the varactor. Optimum operational conditions are defined, as are device dimensions. Finally, the technique is extended to the design of power combiners.

  18. Origin of Open-Circuit Voltage Loss in Polymer Solar Cells and Perovskite Solar Cells.

    Science.gov (United States)

    Kim, Hyung Do; Yanagawa, Nayu; Shimazaki, Ai; Endo, Masaru; Wakamiya, Atsushi; Ohkita, Hideo; Benten, Hiroaki; Ito, Shinzaburo

    2017-06-14

    Herein, the open-circuit voltage (VOC) loss in both polymer solar cells and perovskite solar cells is quantitatively analyzed by measuring the temperature dependence of VOC to discuss the difference in the primary loss mechanism of VOC between them. As a result, the photon energy loss for polymer solar cells is in the range of about 0.7-1.4 eV, which is ascribed to temperature-independent and -dependent loss mechanisms, while that for perovskite solar cells is as small as about 0.5 eV, which is ascribed to a temperature-dependent loss mechanism. This difference is attributed to the different charge generation and recombination mechanisms between the two devices. The potential strategies for the improvement of VOC in both solar cells are further discussed on the basis of the experimental data.

  19. The Cu2ZnSnS4 solar cell with high open circuit voltage

    Science.gov (United States)

    Yang, Min; Ma, Xun; Jiang, Zhi; Li, Zhishan; Liu, Sijia; Lu, Yilei; Wang, Shurong

    2017-03-01

    In this paper, the effects of two different sulfurization processes on the CZTS films were investigated, and the results indicated that a rapid high-temperature crystallization process after sulfurization was beneficial for CZTS thin films to obtain a compact and flat surface with large grains. However, a common sulfurization without rapid high-temperature crystallization process would easily lead to undesirable properties of films, such as rough surface with pin holes, which degenerate the performance of devices. Cu2ZnSnS4 (CZTS) solar cell based on a rapid high-temperature process after sulfurization achieved a high open circuit voltage of 722 mV and the best efficiency 3.32% was obtained.

  20. A Survey of Non-conventional Techniques for Low-voltage Low-power Analog Circuit Design

    Directory of Open Access Journals (Sweden)

    F. Khateb

    2013-06-01

    Full Text Available Designing integrated circuits able to work under low-voltage (LV low-power (LP condition is currently undergoing a very considerable boom. Reducing voltage supply and power consumption of integrated circuits is crucial factor since in general it ensures the device reliability, prevents overheating of the circuits and in particular prolongs the operation period for battery powered devices. Recently, non-conventional techniques i.e. bulk-driven (BD, floating-gate (FG and quasi-floating-gate (QFG techniques have been proposed as powerful ways to reduce the design complexity and push the voltage supply towards threshold voltage of the MOS transistors (MOST. Therefore, this paper presents the operation principle, the advantages and disadvantages of each of these techniques, enabling circuit designers to choose the proper design technique based on application requirements. As an example of application three operational transconductance amplifiers (OTA base on these non-conventional techniques are presented, the voltage supply is only ±0.4 V and the power consumption is 23.5 µW. PSpice simulation results using the 0.18 µm CMOS technology from TSMC are included to verify the design functionality and correspondence with theory.

  1. A Low-Power Voltage Limiter/Regulator IC in Standard Thick-Oxide 130 nm CMOS for Inductive Power Transfer Application

    Directory of Open Access Journals (Sweden)

    Stepan Lapshev

    2014-01-01

    Full Text Available This paper presents a novel CMOS low-power voltage limiter/regulator circuit with hysteresis for inductive power transfer in an implanted telemetry application. The circuit controls its rail voltage to the maximum value of 3 V DC employing 100 mV of comparator hysteresis. It occupies a silicon area of only 127 µm × 125 µm using the 130 nm IBM CMOS process. In addition, the circuit dissipated less than 1 mW and was designed using thick-oxide 3.6 V NMOS and PMOS devices available in the process library.

  2. Study on Factors for Accurate Open Circuit Voltage Characterizations in Mn-Type Li-Ion Batteries

    OpenAIRE

    Natthawuth Somakettarin; Tsuyoshi Funaki

    2017-01-01

    Open circuit voltage (OCV) of lithium batteries has been of interest since the battery management system (BMS) requires an accurate knowledge of the voltage characteristics of any Li-ion batteries. This article presents an OCV characteristic for lithium manganese oxide (LMO) batteries under several experimental operating conditions, and discusses factors for accurate OCV determination. A test system is developed for OCV characterization based on the OCV pulse test method. Various factors for ...

  3. Striatal cholinergic interneuron regulation and circuit effects

    Directory of Open Access Journals (Sweden)

    Sean Austin Lim

    2014-10-01

    Full Text Available The striatum plays a central role in motor control and motor learning. Appropriate responses to environmental stimuli, including pursuit of reward or avoidance of aversive experience all require functional striatal circuits. These pathways integrate synaptic inputs from limbic and cortical regions including sensory, motor and motivational information to ultimately connect intention to action. Although many neurotransmitters participate in striatal circuitry, one critically important player is acetylcholine (ACh. Relative to other brain areas, the striatum contains exceptionally high levels of ACh, the enzymes that catalyze its synthesis and breakdown, as well as both nicotinic and muscarinic receptor types that mediate its postsynaptic effects. The principal source of striatal ACh is the cholinergic interneuron (ChI, which comprises only about 1-2% of all striatal cells yet sends dense arbors of projections throughout the striatum. This review summarizes recent advances in our understanding of the factors affecting the excitability of these neurons through acute effects and long term changes in their synaptic inputs. In addition, we discuss the physiological effects of ACh in the striatum, and how changes in ACh levels may contribute to disease states during striatal dysfunction.

  4. Study on the Mathematical Model of Dielectric Recovery Characteristics in High Voltage SF6 Circuit Breaker

    Science.gov (United States)

    Lin, Xin; Wang, Feiming; Xu, Jianyuan; Xia, Yalong; Liu, Weidong

    2016-03-01

    According to the stream theory, this paper proposes a mathematical model of the dielectric recovery characteristic based on the two-temperature ionization equilibrium equation. Taking the dynamic variation of charged particle's ionization and attachment into account, this model can be used in collaboration with the Coulomb collision model, which gives the relationship of the heavy particle temperature and electron temperature to calculate the electron density and temperature under different pressure and electric field conditions, so as to deliver the breakdown electric field strength under different pressure conditions. Meanwhile an experiment loop of the circuit breaker has been built to measure the breakdown voltage. It is shown that calculated results are in conformity with experiment results on the whole while results based on the stream criterion are larger than experiment results. This indicates that the mathematical model proposed here is more accurate for calculating the dielectric recovery characteristic, it is derived from the stream model with some improvement and refinement and has great significance for increasing the simulation accuracy of circuit breaker's interruption characteristic. supported by Science and Technology Project of State Grid Corporation of China (No. GY17201200063), National Natural Science Foundation of China (No. 51277123), Basic Research Project of Liaoning Key Laboratory of Education Department (LZ2015055)

  5. Fuzzy diagnostic system for oleo-pneumatic drive mechanism of high-voltage circuit breakers.

    Science.gov (United States)

    Nicolau, Viorel

    2013-01-01

    Many oil-based high-voltage circuit breakers are still in use in national power networks of developing countries, like those in Eastern Europe. Changing these breakers with new more reliable ones is not an easy task, due to their implementing costs. The acting device, called oleo-pneumatic mechanism (MOP), presents the highest fault rate from all components of circuit breaker. Therefore, online predictive diagnosis and early detection of the MOP fault tendencies are very important for their good functioning state. In this paper, fuzzy logic approach is used for the diagnosis of MOP-type drive mechanisms. Expert rules are generated to estimate the MOP functioning state, and a fuzzy system is proposed for predictive diagnosis. The fuzzy inputs give information about the number of starts and time of functioning per hour, in terms of short-term components, and their mean values. Several fuzzy systems were generated, using different sets of membership functions and rule bases, and their output performances are studied. Simulation results are presented based on an input data set, which contains hourly records of operating points for a time horizon of five years. The fuzzy systems work well, making an early detection of the MOP fault tendencies.

  6. Fuzzy Diagnostic System for Oleo-Pneumatic Drive Mechanism of High-Voltage Circuit Breakers

    Directory of Open Access Journals (Sweden)

    Viorel Nicolau

    2013-01-01

    Full Text Available Many oil-based high-voltage circuit breakers are still in use in national power networks of developing countries, like those in Eastern Europe. Changing these breakers with new more reliable ones is not an easy task, due to their implementing costs. The acting device, called oleo-pneumatic mechanism (MOP, presents the highest fault rate from all components of circuit breaker. Therefore, online predictive diagnosis and early detection of the MOP fault tendencies are very important for their good functioning state. In this paper, fuzzy logic approach is used for the diagnosis of MOP-type drive mechanisms. Expert rules are generated to estimate the MOP functioning state, and a fuzzy system is proposed for predictive diagnosis. The fuzzy inputs give information about the number of starts and time of functioning per hour, in terms of short-term components, and their mean values. Several fuzzy systems were generated, using different sets of membership functions and rule bases, and their output performances are studied. Simulation results are presented based on an input data set, which contains hourly records of operating points for a time horizon of five years. The fuzzy systems work well, making an early detection of the MOP fault tendencies.

  7. Influence of Copper Vapor on Low-Voltage Circuit Breaker Arcs During Stationary and Moving States

    Institute of Scientific and Technical Information of China (English)

    MA Qiang; RONG Mingzhe; WU Yi; XU Tiejun; SUN Zhiqiang

    2008-01-01

    The influence of copper vapor on the low-voltage circuit breaker arcs is studied. A three-dimensional (3-D) magnetohydrodynamics(MHD) model of arc motion under the effect of external magnetic field is built up. By adopting the commercial computational fluid dynamics (CFD) package FLUENT based on control-volume method, the above MHD model is solved. For the mediums of air-1% Cu and air-10% Cu, the distributions of stationary temperature, pressure, electrical potential and the arc motion processes are compared with those of a pure air arc. The copper vapor diffusion process in the arc chamber and the distribution of copper vapor mass concentration are also simulated. The results shows that the copper vapor has a cooling effect on the arc plasma and can decrease the stationary voltage as well. Moreover, the presence of copper vapor can decelerate the arc motion in the quenching chambers. The maximal copper vapor concentration locates behind the arc root because of the existence of a "double vortex" near the electrodes.

  8. Determining interface properties limiting open-circuit voltage in heterojunction solar cells

    Energy Technology Data Exchange (ETDEWEB)

    Brandt, Riley E. [Massachusetts Institute of Technology, Cambridge, Massachusetts 02139, USA; Mangan, Niall M. [Massachusetts Institute of Technology, Cambridge, Massachusetts 02139, USA; Li, Jian V. [National Renewable Energy Laboratory, 15013 Denver West Parkway, Golden, Colorado 80401, USA; Lee, Yun Seog [Massachusetts Institute of Technology, Cambridge, Massachusetts 02139, USA; Buonassisi, Tonio [Massachusetts Institute of Technology, Cambridge, Massachusetts 02139, USA

    2017-05-09

    The development of new thin-film photovoltaic (PV) absorbers is often hindered by the search for an optimal heterojunction contact; an unoptimized contact may be mistaken for poor quality of the underlying absorber, making it difficult to assess the reasons for poor performance. Therefore, quantifying the loss in device efficiency and open-circuit voltage (VOC) as a result of the interface is a critical step in evaluating a new material. In the present work, we fabricate thin-film PV devices using cuprous oxide (Cu2O), with several different n-type heterojunction contacts. Their current-voltage characteristics are measured over a range of temperatures and illumination intensities (JVTi). We quantify the loss in VOC due to the interface and determine the effective energy gap at the interface. The effective interface gap measured by JVTi matches the gap measured by X-ray photoelectron spectroscopy, albeit with higher energy resolution and an order of magnitude faster. We discuss potential artifacts in JVTi measurements and areas where analytical models are insufficient. Applying JVTi to complete devices, rather than incomplete material stacks, suggests that it can be a quick, accurate method to assess the loss due to unoptimized interface band offsets in thin-film PV devices.

  9. Fuzzy Controller for a Voltage-Regulated Solar-Powered MPPT System for Hybrid Power System Applications

    Directory of Open Access Journals (Sweden)

    Jaw-Kuen Shiau

    2015-04-01

    Full Text Available This paper presents the design of a fuzzy-logic-based voltage-regulated solar power maximum power point tracking (MPPT system for applications involving hybrid power systems. The system contains a solar power system and battery as the primary and secondary power sources, respectively. The solar system alone supplies power to the electric motor and maintains the output voltage at a predetermined level when it has sufficient power. When the solar power is insufficient, the solar system is operated at its maximum power point (MPP and the battery is engaged to compensate for the insufficiency. First, a variant of the incremental conductance MPP condition was established. Under the MPP condition, the voltage-regulated MPPT system was formulated as a feedback control system, where the MPP condition and voltage regulation requirements were used as the system inputs. Next, a fuzzy controller was developed to perform the voltage-regulated MPPT function for the hybrid power system. A simulation model based on Matrix laboratory (MATLAB/SIMULINK (a block diagram environment for multi-domain simulation and model-based design and a piecewise linear electric circuit simulation (PLECS tool for controlling the dc motor velocity was developed to verify the voltage-regulated solar power MPPT system.

  10. Circuits regulating pleasure and happiness in major depression.

    Science.gov (United States)

    Loonen, A J M; Ivanova, S A

    2016-02-01

    The introduction of selective serotonin reuptake inhibitors has gradually changed the borders of the major depression disease class. Anhedonia was considered a cardinal symptom of endogenous depression, but the potential of selective serotonin reuptake inhibitors to treat anxiety disorders has increased the relevance of stress-induced morbidity. This shift has led to an important heterogeneity of current major depressive disorder. The complexity can be disentangled by postulating the existence of two different but mutually interacting neuronal circuits regulating the intensity of anhedonia (lack of pleasure) and dysphoria (lack of happiness). These circuits are functionally dominated by partly closed limbic (regulating misery-fleeing behaviour) and extrapyramidal (regulating reward-seeking behaviour) cortico-striato-thalamo-cortical (CSTC) circuits. The re-entry circuits include the shell and core parts of the accumbens nucleus, respectively. Pleasure can be considered to result from finding relief from the hypermotivation to exhibit rewarding behaviour, and happiness from finding relief from negative or conflicting circumstances. Hyperactivity of the extrapyramidal CSTC circuit results in craving, whereas hyperactivity of the limbic system results in dysphoria.

  11. Ultra high open circuit voltage (>1 V) of poly-3-hexylthiophene based organic solar cells with concentrated light

    DEFF Research Database (Denmark)

    Tromholt, Thomas; Madsen, Morten Vesterager; Krebs, Frederik C

    2013-01-01

    One approach to increasing polymer solar cell efficiency is to blend poly-(3-hexyl-thiophene) with poorly electron accepting fullerene derivatives to obtain higher open circuit voltage (Voc). In this letter concentrated light is used to study the electrical properties of cell operation at up...... to 2000 solar intensities of these photoactive blends. Comparison of solar cells based on five different fullerene derivatives shows that at both short circuit and open circuit conditions, recombination remains unchanged up to 50 suns. Determination of Voc at 2000 suns demonstrated that the same...

  12. Transient Recovery Voltages at the Main 132kV Line Bay GIS Circuit Breaker in a Windfarm

    OpenAIRE

    Arana Aristi, Iván; Okholm, J.; Holbøll, Joachim

    2011-01-01

    This paper presents the results of investigations of the Transient Recovery Voltage (TRV) across the terminals of the main 132kV Line Bay GIS circuit breaker (GIS CB) for Walney 2, second phase of the Walney Offshore Wind Farm. Several simulations were performed where the influence of different parameters in the network was evaluated during a fault in the onshore substation. The rate of rise of recovery voltage (RRRV) and the maximum crest voltage (Uc) of the TRV across the GIS CB were compar...

  13. A New Secondary Control Approach for Voltage Regulation in DC Microgrids

    DEFF Research Database (Denmark)

    Peyghami Akhuleh, Saeed; Mokhtari, Hossein; Davari, Pooya;

    2016-01-01

    feeders with much voltage drop on the line resistances, the conventional methods may not guarantee the voltage regulation on the load busses. Therefore, in addition to compensate the voltage drop of the primary controller, it is necessary to regulate the voltage of critical loads. In this paper, a new...

  14. Perbaikan Jatuh Tegangan Dengan Pemasangan Automatic Voltage Regulator

    Directory of Open Access Journals (Sweden)

    Ija Darmana

    2015-07-01

    Full Text Available Pada jaringan distribusi telah dipertimbangkan kemungkinan-kemungkinan terjadinya penurunan tegangan karena beban puncak akibat penambahan beban dan pelepasan beban disisi konsumen.Dengan adanya variasi beban, maka disisi konsumen pada saat tertentu akan terjadi variasi tegangan yang besarnya berada antara tegangan minimum dan tegangan maksimum. Untuk mengatasi masalah ini, dapat dilakukan dengan pemasangan kapasitor shunt atau pemasangan Automatic Voltage Regulator (AVR. Adapun titik-titik beban tempat pemasangan kapasitor shunt adalah gardu hubung Painan sebesar 600 kVAR. Dengan pemasangan kapasitor ini  profil tegangan di titik beban untuk gardu hubung Painan ke Balai Selasa mengalami kenaikan tetapi belum memenuhi sesuai dengan yang diharapkan karena masih adanya rugi-rugi tegangan gardu hubung Surantih dan Balai Selasa. Oleh karena itu dilakukan pemasangan  Automatic Voltage Regulator (AVR  diletakkan pada gardu hubung Painan.Setelah pemasangan AVR didapat hasil perhitungan kenaikan tegangan pada gardu hubung Painan sebesar 20,4123 kV, Surantih sebesar 19,5916 kV dan Balai Selasa sebesar 18,6180 kV. Setelah pemasangan Automatic Voltage Regulator  (AVR dilakukan pada gardu hubung Painan telah memenuhi stendard kecil dari 10% tegangan normal, artinya performansi sistem distribusi akan menjadi lebih baik dan handalKata kunci : Perbaikan faktor daya, AVR.

  15. Interface Modification of Dye-sensitized Solar Cells with Pivalic Acid to Enhance the Open-circuit Voltage

    KAUST Repository

    Li, Xin

    2009-01-01

    Pivalic acid (PVA) was used as a new coadsorbent to dye-sensitized solar cells (DSCs) to modify the interface between the TiO2 films and electrolyte. The addition of PVA improved the light-to-electricity conversion efficiency of devices by 8% by enhancing the open-circuit voltage. Copyright © 2009 The Chemical Society of Japan.

  16. A fully on-chip fast-transient NMOS low dropout voltage regulator with quasi floating gate pass element

    Science.gov (United States)

    Wang, Han; Gou, Chao; Luo, Kai

    2017-04-01

    This paper presents a fully on-chip NMOS low-dropout regulator (LDO) for portable applications with quasi floating gate pass element and fast transient response. The quasi floating gate structure makes the gate of the NMOS transistor only periodically charged or refreshed by the charge pump, which allows the charge pump to be a small economical circuit with small silicon area. In addition, a variable reference circuit is introduced enlarging the dynamic range of error amplifier during load transient. The proposed LDO has been implemented in a 0.35 μm BCD process. From experimental results, the regulator can operate with a minimum dropout voltage of 250 mV at a maximum 1 A load and {I}{{Q}} of 395 μA. Under full-range load current step, the voltage undershoot and overshoot of the proposed LDO are reduced to 50 and 26 mV, respectively.

  17. Low Voltage Power Efficient Tunable Shaper Circuit With Rail-To-Rail Output Range for the HYDE Detector at FAIR

    Science.gov (United States)

    Galán, J.; López-Ahumada, R.; Sánchez-Rodríguez, T.; Torralba, A.; Carvajal, R. G.; Martel, I.

    2014-04-01

    This paper presents a low voltage, low power readout front-end system implemented in 130 nm CMOS technology. A conventional architecture that consists of charge sensitive amplifier, pole/zero cancellation and shaper has been used. The work focuses on the design of novel circuit topologies in low voltage environment minimizing the power consumption in modern deep submicron CMOS technologies. An operational amplifier with rail-to-rail output swing that uses a gain boosting technique and class-AB output stage without extra power consumption has been used for the shaper. The circuit combines excellent performances with simplicity of design and suitability for low voltage operation. The system is intended to work with silicon detectors for nuclear physics applications and is optimized to match an input capacitance of 10 pF. The system features a peaking time of 500 ns, a power dissipation of 1.57 mW/channel and an equivalent noise charge of 201 e-.

  18. Symmetry-Breaking Charge Transfer in a Zinc Chlorodipyrrin Acceptor for High Open Circuit Voltage Organic Photovoltaics

    KAUST Repository

    Bartynski, Andrew N.

    2015-04-29

    © 2015 American Chemical Society. Low open-circuit voltages significantly limit the power conversion efficiency of organic photovoltaic devices. Typical strategies to enhance the open-circuit voltage involve tuning the HOMO and LUMO positions of the donor (D) and acceptor (A), respectively, to increase the interfacial energy gap or to tailor the donor or acceptor structure at the D/A interface. Here, we present an alternative approach to improve the open-circuit voltage through the use of a zinc chlorodipyrrin, ZCl [bis(dodecachloro-5-mesityldipyrrinato)zinc], as an acceptor, which undergoes symmetry-breaking charge transfer (CT) at the donor/acceptor interface. DBP/ZCl cells exhibit open-circuit voltages of 1.33 V compared to 0.88 V for analogous tetraphenyldibenzoperyflanthrene (DBP)/C60-based devices. Charge transfer state energies measured by Fourier-transform photocurrent spectroscopy and electroluminescence show that C60 forms a CT state of 1.45 ± 0.05 eV in a DBP/C60-based organic photovoltaic device, while ZCl as acceptor gives a CT state energy of 1.70 ± 0.05 eV in the corresponding device structure. In the ZCl device this results in an energetic loss between ECT and qVOC of 0.37 eV, substantially less than the 0.6 eV typically observed for organic systems and equal to the recombination losses seen in high-efficiency Si and GaAs devices. The substantial increase in open-circuit voltage and reduction in recombination losses for devices utilizing ZCl demonstrate the great promise of symmetry-breaking charge transfer in organic photovoltaic devices.

  19. A New Secondary Control Approach for Voltage Regulation in DC Microgrids

    DEFF Research Database (Denmark)

    Peyghami Akhuleh, Saeed; Mokhtari, Hossein; Davari, Pooya

    2016-01-01

    In this paper the effect of secondary controller on voltage regulation in dc Micro-Grids (MGs) is studied. Basically, centralized or decentralized secondary controller has been employed to regulate the voltage drop raised by the primary controller. However, in the case of high capacity MGs and long...... feeders with much voltage drop on the line resistances, the conventional methods may not guarantee the voltage regulation on the load busses. Therefore, in addition to compensate the voltage drop of the primary controller, it is necessary to regulate the voltage of critical loads. In this paper, a new...... voltage regulation strategy is proposed to regulate the voltage of MG by employing the average voltage of identified busses, which are determined by the proposed modal analysis. Numerical steady state analysis and preliminary simulation results validate effectiveness of the proposed scheme. Furthermore...

  20. Static DC to DC Power Conditioning-Active Ripple Filter, 1 MHZ DC to DC Conversion, and Nonlinear Analysis. Ph.D. Thesis; [voltage regulation and conversion circuitry for spacecraft power supplies

    Science.gov (United States)

    Sander, W. A., III

    1973-01-01

    Dc to dc static power conditioning systems on unmanned spacecraft have as their inputs highly fluctuating dc voltages which they condition to regulated dc voltages. These input voltages may be less than or greater than the desired regulated voltages. The design of two circuits which address specific problems in the design of these power conditioning systems and a nonlinear analysis of one of the circuits are discussed. The first circuit design is for a nondissipative active ripple filter which uses an operational amplifier to amplify and cancel the sensed ripple voltage. A dc to dc converter operating at a switching frequency of 1 MHz is the second circuit discussed. A nonlinear analysis of the type of dc to dc converter utilized in designing the 1 MHz converter is included.

  1. Optimal Distributed Voltage Regulation in Power Distribution Networks

    CERN Document Server

    Lam, Albert Y S; Dominguez-Garcia, Alejandro; Tse, David

    2012-01-01

    In this paper, we address the problem of voltage regulation in power distribution networks with deep-penetration of distributed energy resources (DERs), e.g., renewable-based generation, and storage-capable loads such as plug-in hybrid electric vehicles. We cast the problem as an optimization program, where the objective is to minimize the losses in the network subject to constraints on bus voltage magnitudes, limits on active and reactive power injections, transmission line thermal limits and losses. We provide sufficient conditions under which the optimization problem can be solved via its convex relaxation. Using data from existing networks, we show that the conditions are expected to be satisfied by most networks. We also provide an efficient distributed algorithm to solve the problem. The algorithm is asynchronous, with a communication topology that is the same as the electrical network topology. We illustrate the algorithm's performance in the IEEE 34-bus and the 123-bus feeder test systems.

  2. A novel full soft-switching resonant power converter for mid-feeder voltage regulation of low voltage distribution network

    OpenAIRE

    Ji, Chao; Watson, Alan James; Clare, Jon C.; Johnson, Christopher Mark

    2016-01-01

    This paper presents a novel resonant based, high power density power electronics converter solution for mid-feeder voltage regulation of a low voltage (LV) distribution network. Owing to the use of high switching frequency operation and a full soft-switching control strategy, the proposed converter is capable of superimposing LV compensation into the feeder voltage, to achieve a significant system effect with a compact system volume and correspondingly smaller absolute power loss.

  3. Design and test of component circuits of an integrated quantum voltage noise source for Johnson noise thermometry

    Science.gov (United States)

    Yamada, Takahiro; Maezawa, Masaaki; Urano, Chiharu

    2015-11-01

    We present design and testing of a pseudo-random number generator (PRNG) and a variable pulse number multiplier (VPNM) which are digital circuit subsystems in an integrated quantum voltage noise source for Jonson noise thermometry. Well-defined, calculable pseudo-random patterns of single flux quantum pulses are synthesized with the PRNG and multiplied digitally with the VPNM. The circuit implementation on rapid single flux quantum technology required practical circuit scales and bias currents, 279 junctions and 33 mA for the PRNG, and 1677 junctions and 218 mA for the VPNM. We confirmed the circuit operation with sufficiently wide margins, 80-120%, with respect to the designed bias currents.

  4. Analysis of a dc SQUID readout scheme with voltage feedback circuit and low-noise preamplifier

    Science.gov (United States)

    Zeng, Jia; Zhang, Yi; Schmelz, Matthias; Mück, Michael; Krause, Hans-Joachim; Braginski, Alex I.; Lee, Yong-Ho; Stolz, Ronny; Kong, Xiangyan; Xie, Xiaoming; Meyer, Hans-Georg; Offenhäusser, Andreas; Jiang, Mianheng

    2014-08-01

    We analyzed the dc SQUID with voltage feedback circuit (VFC) and a low-noise room-temperature preamplifier to evaluate the feasibility of a low-noise SQUID direct-coupled readout scheme (DRS), possibly eliminating the need for a two-stage scheme employing a SQUID preamplifier. The passive VFC, connected in parallel to the SQUID, consists of a resistor Rs in series with an inductor L s. This inductor is coupled to the SQUID by a mutual inductance Ms. The purpose of the VFC is to increase the SQUID’s flux-to-voltage transfer coefficient ∂V/∂Φ, thus reducing the preamplifier noise contribution δΦpreamp. However, at the same time, VFC introduces the thermal noise of Rs, δΦR, which may not be negligible. Generally, the noise of the readout scheme, δΦreadout, may thus include both δΦpreamp and δΦR, i.e., δΦreadout2 = δΦpreamp2 + δΦR2. To characterize the SQUID operation with VFC we introduced two dimensionless parameters, r = Rs/Rd and Δ = (M s/Mdyn) - (Rs/R d), where Rd and Mdyn = 1/(∂i/∂Φ) are dynamic properties of the SQUID itself. For assumed intrinsic SQUID parameters, we then numerically analyzed the dependence of δΦreadout noise components on r and Δ to determine their suitable ranges and the minimum of δΦreadout. To verify our analysis, we experimentally characterized, in liquid helium, three niobium SQUIDs with VFC, having suitably chosen r and Δ. The measured SQUID system flux noise was on the order of 1 μΦ0/√Hz, comparable to the intrinsic noise of the SQUID itself. The deduced equivalent voltage noise was comparable to that of a SQUID preamplifier in the two-stage readout. Simple single-stage ultra-low-noise SQUID DRS readout was thus demonstrated.

  5. The Series Connected Buck Boost Regulator Concept for High Efficiency Light Weight DC Voltage Regulation

    Science.gov (United States)

    Birchenough, Arthur G.

    2003-01-01

    Improvements in the efficiency and size of DC-DC converters have resulted from advances in components, primarily semiconductors, and improved topologies. One topology, which has shown very high potential in limited applications, is the Series Connected Boost Unit (SCBU), wherein a small DC-DC converter output is connected in series with the input bus to provide an output voltage equal to or greater than the input voltage. Since the DC-DC converter switches only a fraction of the power throughput, the overall system efficiency is very high. But this technique is limited to applications where the output is always greater than the input. The Series Connected Buck Boost Regulator (SCBBR) concept extends partial power processing technique used in the SCBU to operation when the desired output voltage is higher or lower than the input voltage, and the implementation described can even operate as a conventional buck converter to operate at very low output to input voltage ratios. This paper describes the operation and performance of an SCBBR configured as a bus voltage regulator providing 50 percent voltage regulation range, bus switching, and overload limiting, operating above 98 percent efficiency. The technique does not provide input-output isolation.

  6. Theoretical investigation of the open circuit voltage: P3HT/9,9'-bisfluorenylidene derivative devices.

    Science.gov (United States)

    Carlotto, Silvia

    2014-07-03

    The calculation of the power conversion efficiency (PCE) value for a bulk heterojunction (BHJ) organic solar cell is complex due to the wide number of parameters involved in the processes. This study focuses the attention on the molecular parameters involved into the open circuit voltage and the PCE definitions and in particular on the electronic coupling and on the lowest unoccupied molecular orbital (LUMO) of the acceptor. A simplified model system composed by a polymer as donor and a novel class of molecules (9,9'-bisfluorenylidene derivatives) as acceptor has been proposed as prototype to simulate the BHJ organic solar cell interface. Several substituents on different positions are tested and the chemical nature/position of substituents have a relevant influence on the electronic coupling and energy level values. Geometrical and electronic properties are obtained using density functional theory (DFT) and time-dependent (TD)-DFT calculations, respectively. A new hypothesis suggests that the minimization of the electronic coupling between the LUMO of the acceptor and the highest occupied molecular orbital (HOMO) of the donor can enhance the PCE reducing the recombination interface processes and calculations showing the possibility to minimize this parameter and fine-tune acceptor energy level through the acceptor functionalization. An accurate balance between electronic coupling and on the LUMO of the acceptor allows to propose the more performing candidate as electron acceptor in a P3HT/99'BF derivative BHJ solar cell.

  7. Simulation and Experimental Study of Arc Column Expansion After Ignition in Low-Voltage Circuit Breakers

    Institute of Scientific and Technical Information of China (English)

    MA Qiang; RONG Mingzhe; WU Yi; XU Tiejun; SUN Zhiqiang

    2008-01-01

    The dynamicprocess of arc pressure and corresponding arc column expansion, which is the main feature after arc ignition and has a significant effect on the breaking behaviour of low -voltage circuit breakers, is studied. By constructing a three dimensional mathematical model of air arc plasma and adopting the Control Volume Method, the parameters of arc plasma including temperature and pressure axe obtained. The variations of pressure field and temperature field with time are simulated. The result indicates that there are six stages for the process of arc column expansion according to the variation of pressure in arc chamber. In the first stage, the maximal pressure locates in the region close to cathode, and in the second stage the maximal pressure shifts to the region close to the anode. In the third stage, the pressure difference between the middle of arc column and the ambient gas is very large, so the arc column begins to expand apparently. In the fourth stage, the pressure wave propagates towards both ends and the maximal pressure appears at the two ends when the pressure wave reaches both sidewalls. In the fifth stage, the pressure wave is reflected and collides in the middle of the arc chamber. In the last stage, the propagation and reflection of pressure wave will repeat several times until a steady burning state is reached. In addition, the experimental results of arc column expansion, corresponding to the arc pressure variation, are presented to verify the simulation results.

  8. SOI-Based High-Voltage, High-Temperature Integrated Circuit Gate Driver for SiC-Based Power FETs

    Energy Technology Data Exchange (ETDEWEB)

    Huque, Mohammad A [ORNL; Tolbert, Leon M [ORNL; Blalock, Benjamin [University of Tennessee, Knoxville (UTK); Islam, Syed K [University of Tennessee, Knoxville (UTK)

    2010-01-01

    Silicon carbide (SiC)-based field effect transistors (FETs) are gaining popularity as switching elements in power electronic circuits designed for high-temperature environments like hybrid electric vehicle, aircraft, well logging, geothermal power generation etc. Like any other power switches, SiC-based power devices also need gate driver circuits to interface them with the logic units. The placement of the gate driver circuit next to the power switch is optimal for minimizing system complexity. Successful operation of the gate driver circuit in a harsh environment, especially with minimal or no heat sink and without liquid cooling, can increase the power-to-volume ratio as well as the power-to-weight ratio for power conversion modules such as a DC-DC converter, inverter etc. A silicon-on-insulator (SOI)-based high-voltage, high-temperature integrated circuit (IC) gate driver for SiC power FETs has been designed and fabricated using a commercially available 0.8-m, 2-poly and 3-metal bipolar-complementary metal oxide semiconductor (CMOS)-double diffused metal oxide semiconductor (DMOS) process. The prototype circuit-s maximum gate drive supply can be 40-V with peak 2.3-A sourcing/sinking current driving capability. Owing to the wide driving range, this gate driver IC can be used to drive a wide variety of SiC FET switches (both normally OFF metal oxide semiconductor field effect transistor (MOSFET) and normally ON junction field effect transistor (JFET)). The switching frequency is 20-kHz and the duty cycle can be varied from 0 to 100-. The circuit has been successfully tested with SiC power MOSFETs and JFETs without any heat sink and cooling mechanism. During these tests, SiC switches were kept at room temperature and ambient temperature of the driver circuit was increased to 200-C. The circuit underwent numerous temperature cycles with negligible performance degradation.

  9. Fabrication of Ultra-Thin Printed Organic TFT CMOS Logic Circuits Optimized for Low-Voltage Wearable Sensor Applications.

    Science.gov (United States)

    Takeda, Yasunori; Hayasaka, Kazuma; Shiwaku, Rei; Yokosawa, Koji; Shiba, Takeo; Mamada, Masashi; Kumaki, Daisuke; Fukuda, Kenjiro; Tokito, Shizuo

    2016-05-09

    Ultrathin electronic circuits that can be manufactured by using conventional printing technologies are key elements necessary to realize wearable health sensors and next-generation flexible electronic devices. Due to their low level of power consumption, complementary (CMOS) circuits using both types of semiconductors can be easily employed in wireless devices. Here, we describe ultrathin CMOS logic circuits, for which not only the source/drain electrodes but also the semiconductor layers were printed. Both p-type and n-type organic thin film transistor devices were employed in a D-flip flop circuit in the newly developed stacked structure and exhibited excellent electrical characteristics, including good carrier mobilities of 0.34 and 0.21 cm(2) V(-1) sec(-1), and threshold voltages of nearly 0 V with low operating voltages. These printed organic CMOS D-flip flop circuits exhibit operating frequencies of 75 Hz and demonstrate great potential for flexible and printed electronics technology, particularly for wearable sensor applications with wireless connectivity.

  10. Design and test of component circuits of an integrated quantum voltage noise source for Johnson noise thermometry

    Energy Technology Data Exchange (ETDEWEB)

    Yamada, Takahiro, E-mail: yamada-takahiro@aist.go.jp [Nanoelectronics Research Institute, National Institute of Advanced Industrial Science and Technology, Central 2, Umezono 1-1-1, Tsukuba, Ibaraki 305-8568 (Japan); Maezawa, Masaaki [Nanoelectronics Research Institute, National Institute of Advanced Industrial Science and Technology, Central 2, Umezono 1-1-1, Tsukuba, Ibaraki 305-8568 (Japan); Urano, Chiharu [National Metrology Institute of Japan, National Institute of Advanced Industrial Science and Technology, Central 3, Umezono 1-1-1, Tsukuba, Ibaraki 305-8563 (Japan)

    2015-11-15

    Highlights: • We demonstrated RSFQ digital components of a new quantum voltage noise source. • A pseudo-random number generator and variable pulse number multiplier are designed. • Fabrication process is based on four Nb wiring layers and Nb/AlOx/Nb junctions. • The circuits successfully operated with wide dc bias current margins, 80–120%. - Abstract: We present design and testing of a pseudo-random number generator (PRNG) and a variable pulse number multiplier (VPNM) which are digital circuit subsystems in an integrated quantum voltage noise source for Jonson noise thermometry. Well-defined, calculable pseudo-random patterns of single flux quantum pulses are synthesized with the PRNG and multiplied digitally with the VPNM. The circuit implementation on rapid single flux quantum technology required practical circuit scales and bias currents, 279 junctions and 33 mA for the PRNG, and 1677 junctions and 218 mA for the VPNM. We confirmed the circuit operation with sufficiently wide margins, 80–120%, with respect to the designed bias currents.

  11. Fabrication of Ultra-Thin Printed Organic TFT CMOS Logic Circuits Optimized for Low-Voltage Wearable Sensor Applications

    Science.gov (United States)

    Takeda, Yasunori; Hayasaka, Kazuma; Shiwaku, Rei; Yokosawa, Koji; Shiba, Takeo; Mamada, Masashi; Kumaki, Daisuke; Fukuda, Kenjiro; Tokito, Shizuo

    2016-05-01

    Ultrathin electronic circuits that can be manufactured by using conventional printing technologies are key elements necessary to realize wearable health sensors and next-generation flexible electronic devices. Due to their low level of power consumption, complementary (CMOS) circuits using both types of semiconductors can be easily employed in wireless devices. Here, we describe ultrathin CMOS logic circuits, for which not only the source/drain electrodes but also the semiconductor layers were printed. Both p-type and n-type organic thin film transistor devices were employed in a D-flip flop circuit in the newly developed stacked structure and exhibited excellent electrical characteristics, including good carrier mobilities of 0.34 and 0.21 cm2 V‑1 sec‑1, and threshold voltages of nearly 0 V with low operating voltages. These printed organic CMOS D-flip flop circuits exhibit operating frequencies of 75 Hz and demonstrate great potential for flexible and printed electronics technology, particularly for wearable sensor applications with wireless connectivity.

  12. Index-based reactive power compensation scheme for voltage regulation

    Science.gov (United States)

    Dike, Damian Obioma

    2008-10-01

    to optimal utilization of compensation devices and available transfer capability as well as reduce system outages through better regulation of power operating voltages.

  13. On-line monitoring of base current and forward emitter current gain of the voltage regulator's serial pnp transistor in a radiation environment

    Directory of Open Access Journals (Sweden)

    Vukić Vladimir Đ.

    2012-01-01

    Full Text Available A method of on-line monitoring of the low-dropout voltage regulator's operation in a radiation environment is developed in this paper. The method had to enable detection of the circuit's degradation during exploitation, without terminating its operation in an ionizing radiation field. Moreover, it had to enable automatic measurement and data collection, as well as the detection of any considerable degradation, well before the monitored voltage regulator's malfunction. The principal parameters of the voltage regulator's operation that were monitored were the serial pnp transistor's base current and the forward emitter current gain. These parameters were procured indirectly, from the data on the voltage regulator's load and quiescent currents. Since the internal consumption current in moderately and heavily loaded devices was used, the quiescent current of a negligibly loaded voltage regulator of the same type served as a reference. Results acquired by on-line monitoring demonstrated marked agreement with the results acquired from examinations of the voltage regulator's maximum output current and minimum dropout voltage in a radiation environment. The results were particularly consistent in tests with heavily loaded devices. Results obtained for moderately loaded voltage regulators and the risks accompanying the application of the presented method, were also analyzed.

  14. Endogenous polyamines regulate cortical neuronal excitability by blocking voltage-gated Na+ channels.

    Science.gov (United States)

    Fleidervish, Ilya A; Libman, Lior; Katz, Efrat; Gutnick, Michael J

    2008-12-02

    Because the excitable properties of neurons in the neocortex depend on the characteristics of voltage-gated Na(+) channels, factors which regulate those characteristics can fundamentally modify the dynamics of cortical circuits. Here, we report on a novel neuromodulatory mechanism that links the availability of Na(+) channels to metabolism of polyamines (PAs) in the cerebral cortex. Using single channel and whole-cell recordings, we found that products of PA metabolism, the ubiquitous aliphatic polycations spermine and spermidine, are endogenous blockers of Na(+) channels in layer 5 pyramidal cells. Because the blockade is activity-dependent, it is particularly effective against Na(+) channels which fail to inactivate rapidly and thus underlie the persistent Na(+) current. At the level of the local cortical circuit, pharmacological depletion of PAs led to increased spontaneous spiking and periods of hypersynchronous discharge. Our data suggest that changes in PA levels, whether associated with normal brain states or pathological conditions, profoundly modify Na(+) channel availability and thereby shape the integrative behavior of single neurons and neocortical circuits.

  15. Simulation Study on the Open-Circuit Voltage of Amorphous Silicon p-i-n Solar Cells Using AMPS-1D

    Directory of Open Access Journals (Sweden)

    B.M. Omer

    2014-04-01

    Full Text Available AMPS-1D (Analysis of Microelectronic and Photonic Structure simulation program was used to simulate Amorphous Silicon p-i-n Solar Cell. The simulated result of illuminated current density-voltage characteristics was in a good agreement with experimental values. The dependence of the open-circuit voltage on the characteristics of the a-Si:H intrinsic layer was investigated. The simulation result shows that the open-circuit voltage does not depend on the thickness of the intrinsic layer. The open-circuit voltage decreases when the front contact barrier height is small or the energy gap of the intrinsic layer is small. The open-circuit voltage increases when the distribution of the tail states is sharp or the capture cross sections of these states are small.

  16. Tesla’s high voltage and high frequency generators with oscillatory circuits

    Directory of Open Access Journals (Sweden)

    Cvetić Jovan M.

    2016-01-01

    Full Text Available The principles that represent the basics of the work of the high voltage and high frequency generator with oscillating circuits will be discussed. Until 1891, Tesla made and used mechanical generators with a large number of extruded poles for the frequencies up to about 20 kHz. The first electric generators based on a new principle of a weakly coupled oscillatory circuits he used for the wireless signal transmission, for the study of the discharges in vacuum tubes, the wireless energy transmission, for the production of the cathode rays, that is x-rays and other experiments. Aiming to transfer the signals and the energy to any point of the surface of the Earth, in the late of 19th century, he had discovered and later patented a new type of high frequency generator called a magnifying transmitter. He used it to examine the propagation of electromagnetic waves over the surface of the Earth in experiments in Colorado Springs in the period 1899-1900. Tesla observed the formation of standing electromagnetic waves on the surface of the Earth by measuring radiated electric field from distant lightning thunderstorm. He got the idea to generate the similar radiation to produce the standing waves. On the one hand, signal transmission, i.e. communication at great distances would be possible and on the other hand, with more powerful and with at least three magnifying transmitters the wireless transmission of energy without conductors at any point of the Earth surface could also be achieved. The discovery of the standing waves on the surface of the Earth and the invention of the magnifying transmitter he claimed his greatest inventions. Less than two years later, at the end of 1901, he designed and started to build a much stronger magnifying transmitter on Long Island near New York City (the Wardenclyffe tower wishing to become a world telecommunication center. During the tower construction, he elaborated the plans for an even stronger transmitter based on

  17. Study program to improve the open-circuit voltage of low resistivity single crystal silicon solar cells

    Science.gov (United States)

    Minnucci, J. A.; Matthei, K. W.

    1980-01-01

    The results of a 14 month program to improve the open circuit voltage of low resistivity silicon solar cells are described. The approach was based on ion implantation in 0.1- to 10.0-ohm-cm float-zone silicon. As a result of the contract effort, open circuit voltages as high as 645 mV (AMO 25 C) were attained by high dose phosphorus implantation followed by furnace annealing and simultaneous SiO2 growth. One key element was to investigate the effects of bandgap narrowing caused by high doping concentrations in the junction layer. Considerable effort was applied to optimization of implant parameters, selection of furnace annealing techniques, and utilization of pulsed electron beam annealing to minimize thermal process-induced defects in the completed solar cells.

  18. The effect of diffusion induced lattice stress on the open-circuit voltage in silicon solar cells

    Science.gov (United States)

    Weizer, V. G.; Godlewski, M. P.

    1984-01-01

    It is demonstrated that diffusion induced stresses in low resistivity silicon solar cells can significantly reduce both the open-circuit voltage and collection efficiency. The degradation mechanism involves stress induced changes in both the minority carrier mobility and the diffusion length. Thermal recovery characteristics indicate that the stresses are relieved at higher temperatures by divacancy flow (silicon self diffusion). The level of residual stress in as-fabricated cells was found to be negligible in the cells tested.

  19. A new generation of medium-voltage switchboards and circuit-breakers; Eine neue Generation von Mittelspannungsschaltanlagen und -leistungsschaltern

    Energy Technology Data Exchange (ETDEWEB)

    Saemann, D.; Weichert, R.; Werner, S. [Siemens AG, Erlangen (Germany). Bereich Energieuebertragung und -verteilung

    1998-04-06

    Todays market and the trend towards globalization of business both call for new products. The authors describe the new generation of medium-voltage switchgears and circuit-breakers, along with the benefit they bring for customers. (orig./RHM) [Deutsch] Der Markt und die Globalisierung des Geschaeftes fordern neue Produkte. Die Verfasser beschreiben die neue Generation von Mittelspannungsschaltanlagen und -schaltern sowie deren Nutzen fuer die Anwender. (orig./RHM)

  20. Limitations on the open-circuit voltage imposed by P/+/ and N/+/ regions in silicon solar cells

    Science.gov (United States)

    Shibib, M. A.; Fossum, J. G.

    1981-02-01

    It is shown theoretically and experimentally that the emitter recombination current, which limits the open-circuit voltage of silicon solar cells, can be more easily suppressed in P(+)N cells than in N(+)P cells. This result is due to fundamental effects that occur in heavily doped silicon: degeneracy of the majority charge carriers, Auger recombination, and energy-band-gap narrowing. Cell designs to suppress the emitter current are discussed, and experimental data supporting our theoretical analysis are presented.

  1. Electromagnetic compatibility between secondary and high voltage circuits; Compatibilidade eletromagnetica entre circuitos secundarios e de alta tensao

    Energy Technology Data Exchange (ETDEWEB)

    Alves, Mario Fabiano [Pontificia Univ. Catolica de Minas Gerais, Belo Horizonte, MG (Brazil)

    1997-11-01

    Electromagnetic fields generated by high voltage circuits may affect the performance of sensible loads in an electric power substation. In order to reduce such interferences, and guarantee the adequate performance of the equipment, this work proposes some measures which may be applied to the project during the installation phase, such as the equalization of high frequency power, and the utilization of protective equipment as well as the integration of grounding systems 9 refs., 3 figs.

  2. Understanding device-structure-induced variations in open-circuit voltage for organic photovoltaics.

    Science.gov (United States)

    Wang, Zhiping; Uemura, Yu; Zhou, Ying; Miyadera, Tetsuhiko; Azumi, Reiko; Yoshida, Yuji; Chikamatsu, Masayuki

    2015-05-27

    We investigate the structural influences on the device performance, especially on open-circuit voltage (V(OC)) in squaraine (SQ)/fullerene (C60) bilayer cells. Simply changing the SQ thickness could lead to 40% variation in V(OC) from 0.62 to 0.86 V. The ionization potential (IP) of SQ films and recombination at the anode surface as well as donor/acceptor (D/A) interface sensitively vary with film thicknesses, which account for the shifts in V(OC). The anode recombination can be effectively suppressed by preventing direct contact between C60 and the anode with a buffer layer, delivering an elevated V(OC). Through polarized infrared-multiple-angle incidence resolution spectroscopy measurement, the molecular structure of SQ films is found to gradually evolve from lying-down on indium-tin oxide substrates with noncentrosymmetric orientation at low thicknesses to random structure at high thicknesses. The different molecular orientation may yield different strengths of electronic coupling, which affects the charge-carrier recombination and thus V(OC). Moreover, the oriented SQ films would spontaneously compose aligned dipole moments at the D/A interface because of the strong dipolar effects in SQ molecules identified by density functional theory calculations, whereas no aligned interfacial dipole moment exists in the random structure. The resulting interfacial dipole moments would form an electric field at the D/A interface, leading to variations in the IP and thus impacting V(OC). Our findings demonstrate that V(OC) in organic photovoltaic cells is critically associated with the molecular orientation that affects the charge-carrier recombination and interfacial dipole alignment, which should be seriously taken into consideration for the design of organic molecules and optimization of the cell efficiency.

  3. NBTI-Aware Transient Fault Rate Analysis Method for Logic Circuit Based on Probability Voltage Transfer Characteristics

    Directory of Open Access Journals (Sweden)

    Zhiming Yang

    2016-01-01

    Full Text Available The reliability of Very Large Scale Integration (VLSI circuits has become increasingly susceptible to transient faults induced by environmental noise with the scaling of technology. Some commonly used fault tolerance strategies require statistical methods to accurately estimate the fault rate in different parts of the logic circuit, and Monte Carlo (MC simulation is often applied to complete this task. However, the MC method suffers from impractical computation costs due to the size of the circuits. Furthermore, circuit aging effects, such as negative bias temperature instability (NBTI, will change the characteristics of the circuit during its lifetime, leading to a change in the circuit’s noise margin. This change will increase the complexity of transient fault rate estimation tasks. In this paper, an NBTI-aware statistical analysis method based on probability voltage transfer characteristics is proposed for combinational logic circuit. This method can acquire accurate fault rates using a discrete probability density function approximation process, thus resolving the computation cost problem of the MC method. The proposed method can also consider aging effects and analyze statistical changes in the fault rates. Experimental results demonstrate that, compared to the MC simulation, our method can achieve computation times that are two orders of magnitude shorter while maintaining an error rate less than 9%.

  4. Fast Responding Voltage Regulator and Dynamic VAR Compensator

    Energy Technology Data Exchange (ETDEWEB)

    Divan, Deepak [Varentec, Incorporated, San Jose, CA (United States); Moghe, Rohit [Varentec, Incorporated, San Jose, CA (United States); Tholomier, Damien [Varentec, Incorporated, San Jose, CA (United States)

    2014-12-31

    The objectives of this project were to develop a dynamic VAR compensator (DVC) for voltage regulation through VAR support to demonstrate the ability to achieve greater levels of voltage control on electricity distribution networks, and faster response compared to existing grid technology. The goal of the project was to develop a prototype Fast Dynamic VAR Compensator (Fast DVC) hardware device, and this was achieved. In addition to developing the dynamic VAR compensator device, Varentec in partnership with researchers at North Carolina State University (NCSU) successfully met the objectives to model the potential positive impact of such DVCs on representative power networks. This modeling activity validated the ability of distributed dynamic VAR compensators to provide fast voltage regulation and reactive power control required to respond to grid disturbances under high penetration of fluctuating and intermittent distributed energy resources (DERs) through extensive simulation studies. Specifically the following tasks were set to be accomplished: 1) Development of dynamic VAR compensator to support dynamic voltage variations on the grid through VAR control 2) Extensive testing of the DVC in the lab environment 3) Present the operational DVC device to the DOE at Varentec’s lab 4) Formulation of a detailed specification sheet, unit assembly document, test setup document, unit bring-up plan, and test plan 5) Extensive simulations of the DVC in a system with high PV penetration. Understanding the operation with many DVC on a single distribution system 6) Creation and submittal of quarterly and final reports conveying the design documents, unit performance data, modeling simulation charts and diagrams, and summary explanations of the satisfaction of program goals. This report details the various efforts that led to the development of the Fast DVC as well as the modeling & simulation results. The report begins with the introduction in Section II which outlines the

  5. Approaches to Suppressing Shaft Voltage in Brushless DC Motor Driven by PWM Inverter Based on Ungrounded Common-Mode Equivalent Circuit

    Science.gov (United States)

    Maetani, Tatsuo; Isomura, Yoshinori; Watanabe, Akihiko; Iimori, Kenichi; Morimoto, Shigeo

    This paper describes an ungrounded common-mode equivalent circuit for a motor driven by a voltage-source PWM inverter. When the capacitance of the rotor was is small, the reversal of the polarities of the common-mode voltage and shaft voltage is observed. In order to model this reversal, a bridge-type equivalent circuit is proposed. On the basis of calculations and experiment, it is found the values and polarity of the shaft voltage can be are accurately determined with the proposed equivalent circuit. Furthermore, the capacitance value of the insulated rotor required to make the shaft voltage equal to or less than the dielectric breakdown voltage of the bearing grease is obtained.

  6. Interface band gap narrowing behind open circuit voltage losses in Cu2ZnSnS4 solar cells

    DEFF Research Database (Denmark)

    Crovetto, Andrea; Palsgaard, Mattias Lau Nøhr; Gunst, Tue

    2017-01-01

    We present evidence that bandgap narrowing at the heterointerface may be a major cause of the large open circuit voltage deficit of Cu2ZnSnS4/CdS solar cells. Bandgap narrowing is caused by surface states that extend the Cu2ZnSnS4valence band into the forbidden gap. Those surface states are consi......We present evidence that bandgap narrowing at the heterointerface may be a major cause of the large open circuit voltage deficit of Cu2ZnSnS4/CdS solar cells. Bandgap narrowing is caused by surface states that extend the Cu2ZnSnS4valence band into the forbidden gap. Those surface states...... Zn to passivate those surface states. Focusing future research on Zn-based buffers is expected to significantly improve the open circuit voltage and efficiency of pure-sulfide Cu2ZnSnS4 solar cells....

  7. Ultra-high open-circuit voltage of perovskite solar cells induced by nucleation thermodynamics on rough substrates

    Science.gov (United States)

    Li, Yan; Ding, Bin; Chu, Qian-Qian; Yang, Guan-Jun; Wang, Mingkui; Li, Chang-Xin; Li, Chang-Jiu

    2017-01-01

    To obtain high performance CH3NH3PbI3 perovskite solar cells, it is highly important to realise a high open-circuit voltage. Calculation results based on a modified diode model have indicated that a low bare ratio ϕ of the perovskite film is the most important factor determining the open-circuit voltage, where ϕ is defined as the ratio of the projection of the uncovered area of the perovskite film to the apparent area of the total substrate surface. To realise a low ϕ, we investigate the nucleation behaviour of crystals on rough substrates. The analysis results predict that, when CH3NH3PbI3 is deposited on conventional transparent conductive oxide substrates such as fluorine-doped tin oxide, preferential heterogeneous nucleation will occur on the concave regions of the substrate; then, depending on the subsequent growth step, full coverage of the perovskite film at both the macroscopic and microscopic scales is realised. As a result, an ultra-high open-circuit voltage, i.e., 1.20 V, can be achieved in devices using the full coverage CH3NH3PbI3 film. The thermodynamics theory of precipitation nucleation should shed light on solution engineering of thin films. PMID:28401890

  8. Ultra-high open-circuit voltage of perovskite solar cells induced by nucleation thermodynamics on rough substrates

    Science.gov (United States)

    Li, Yan; Ding, Bin; Chu, Qian-Qian; Yang, Guan-Jun; Wang, Mingkui; Li, Chang-Xin; Li, Chang-Jiu

    2017-04-01

    To obtain high performance CH3NH3PbI3 perovskite solar cells, it is highly important to realise a high open-circuit voltage. Calculation results based on a modified diode model have indicated that a low bare ratio ϕ of the perovskite film is the most important factor determining the open-circuit voltage, where ϕ is defined as the ratio of the projection of the uncovered area of the perovskite film to the apparent area of the total substrate surface. To realise a low ϕ, we investigate the nucleation behaviour of crystals on rough substrates. The analysis results predict that, when CH3NH3PbI3 is deposited on conventional transparent conductive oxide substrates such as fluorine-doped tin oxide, preferential heterogeneous nucleation will occur on the concave regions of the substrate; then, depending on the subsequent growth step, full coverage of the perovskite film at both the macroscopic and microscopic scales is realised. As a result, an ultra-high open-circuit voltage, i.e., 1.20 V, can be achieved in devices using the full coverage CH3NH3PbI3 film. The thermodynamics theory of precipitation nucleation should shed light on solution engineering of thin films.

  9. Enhancement in open-circuit voltage of implantable CMOS-compatible glucose fuel cell by improving the anodic catalyst

    Science.gov (United States)

    Niitsu, Kiichi; Ando, Takashi; Kobayashi, Atsuki; Nakazato, Kazuo

    2017-01-01

    This paper presents an implantable CMOS-compatible glucose fuel cell that generates an open-circuit voltage (OCV) of 880 mV. The developed fuel cell is solid-catalyst-based and manufactured from biocompatible materials; thus, it can be implanted to the human body. Additionally, since the cell can be manufactured using a semiconductor (CMOS) fabrication process, it can also be manufactured together with CMOS circuits on a single silicon wafer. In the literature, an implantable CMOS-compatible glucose fuel cell has been reported. However, its OCV is 192 mV, which is insufficient for CMOS circuit operation. In this work, we have enhanced the performance of the fuel cell by improving the electrocatalytic ability of the anode. The prototype with the newly proposed Pt/carbon nanotube (CNT) anode structure successfully achieved an OCV of 880 mV, which is the highest ever reported.

  10. The correlation of open-circuit voltage with bandgap in amorphous silicon-based {ital pin} solar cells

    Energy Technology Data Exchange (ETDEWEB)

    Crandall, R.S. [National Renewable Energy Laboratory, Golden, Colorado 80401 (United States); Schiff, E.A. [Department of Physics, Syracuse University, Syracuse, New York 13244-1130 (United States)

    1996-01-01

    We briefly review the correlation of open-circuit voltages {ital V}{sub OC} with the bandgap of the intrinsic layer in amorphous silicon based {ital pin} solar cells. We discuss two mechanisms which limit {ital V}{sub OC}: intrinsic layer recombination, and the built-in potential {ital V}{sub BI}. In particular we discuss Li{close_quote}s proposal that the open-circuit voltages in higher bandgap cells ({ital E}{sub G}{gt}1.9 eV) are {ital V}{sub BI}-limited. Based on computer simulations of {ital pin} solar cells we propose that {ital V}{sub BI} limitation occurs when the recombination limit to {ital V}{sub OC} exceeds the cell{close_quote}s field-reversal voltage {ital V}{sub R}. For {ital a}-Si:H based cells this field-reversal voltage occurs at about {ital V}{sub BI}-0.3 V. This proposal would account for the observation that {ital V}{sub BI} limitation occurs for {ital V}{sub OC} significantly smaller than {ital V}{sub BI}. {copyright} {ital 1996 American Institute of Physics.}

  11. Polycrystalline silicon thin-film solar cells prepared by layered laser crystallization with 540 mV open circuit voltage

    Energy Technology Data Exchange (ETDEWEB)

    Plentz, Jonathan, E-mail: jonathan.plentz@ipht-jena.de [Leibniz Institute of Photonic Technology, Albert-Einstein-Str. 9, 07745 Jena (Germany); Experimental Physics I, Institute of Physics, Ilmenau University of Technology, Weimarer Str. 32, 98693 Ilmenau (Germany); Andrä, Gudrun; Gawlik, Annett; Höger, Ingmar; Jia, Guobin; Falk, Fritz [Leibniz Institute of Photonic Technology, Albert-Einstein-Str. 9, 07745 Jena (Germany)

    2014-07-01

    Polycrystalline silicon thin film solar cells on a glass substrate are investigated. The solar cell layer structure was generated by a two-step process in which first a 100–600 nm thin seed layer is formed by diode laser crystallization of electron beam evaporated amorphous silicon. In a second step this layer is epitaxially thickened to 2–3.5 μm by layered laser crystallization. In this process further amorphous silicon is deposited and in situ repeatedly is irradiated by excimer laser pulses. The polycrystalline layer consists of grains several hundreds of microns long and several tens of microns wide and it contains a p{sup +}–p–n{sup +} doping profile. After deposition a rapid thermal annealing and hydrogen passivation steps follow. The back and front contacts are prepared after mesa structuring. The influence of the seed layer thickness on the solar cell performance was investigated. In addition, the absorber contamination due to the background pressure during absorber deposition and its influence on the short circuit current density was investigated. The best parameters reached for various solar cells are 540 mV open circuit voltage, 20.3 mA/cm{sup 2} short circuit current density (without light trapping), 75% fill factor, and 5.2% efficiency. - Highlights: • Layered laser crystallization leads to grain sizes of 10–300 μm on glass. • Open circuit voltage of 540 mV and efficiency of 5.2% are achieved. • Short circuit current is influenced by background pressure during deposition. • Short circuit current density of 20.3 mA/cm{sup 2} is reached without light trapping. • Progress requires pressures below 10{sup −7} hPa and deposition rates over 100 nm/min.

  12. Study on Factors for Accurate Open Circuit Voltage Characterizations in Mn-Type Li-Ion Batteries

    Directory of Open Access Journals (Sweden)

    Natthawuth Somakettarin

    2017-03-01

    Full Text Available Open circuit voltage (OCV of lithium batteries has been of interest since the battery management system (BMS requires an accurate knowledge of the voltage characteristics of any Li-ion batteries. This article presents an OCV characteristic for lithium manganese oxide (LMO batteries under several experimental operating conditions, and discusses factors for accurate OCV determination. A test system is developed for OCV characterization based on the OCV pulse test method. Various factors for the OCV behavior, such as resting period, step-size of the pulse test, testing current amplitude, hysteresis phenomena, and terminal voltage relationship, are investigated and evaluated. To this end, a general OCV model based on state of charge (SOC tracking is developed and validated with satisfactory results.

  13. A High-Voltage Integrated Circuit Engine for a Dielectrophoresis-based Programmable Micro-Fluidic Processor

    Science.gov (United States)

    Current, K. Wayne; Yuk, Kelvin; McConaghy, Charles; Gascoyne, Peter R. C.; Schwartz, Jon A.; Vykoukal, Jody V.; Andrews, Craig

    2010-01-01

    A high-voltage (HV) integrated circuit has been demonstrated to transport droplets on programmable paths across its coated surface. This chip is the engine for a dielectrophoresis (DEP)-based micro-fluidic lab-on-a-chip system. This chip creates DEP forces that move and help inject droplets. Electrode excitation voltage and frequency are variable. With the electrodes driven with a 100V peak-to-peak periodic waveform, the maximum high-voltage electrode waveform frequency is about 200Hz. Data communication rate is variable up to 250kHz. This demonstration chip has a 32×32 array of nominally 100V electrode drivers. It is fabricated in a 130V SOI CMOS fabrication technology, dissipates a maximum of 1.87W, and is about 10.4 mm × 8.2 mm. PMID:23989241

  14. TAURINE REGULATION OF VOLTAGE-GATED CHANNELS IN RETINAL NEURONS

    Science.gov (United States)

    Rowan, Matthew JM; Bulley, Simon; Purpura, Lauren; Ripps, Harris; Shen, Wen

    2017-01-01

    Taurine activates not only Cl−-permeable ionotropic receptors, but also receptors that mediate metabotropic responses. The metabotropic property of taurine was revealed in electrophysiological recordings obtained after fully blocking Cl−-permeable receptors with an inhibitory “cocktail” consisting of picrotoxin, SR95531, and strychnine. We found that taurine’s metabotropic effects regulate voltage-gated channels in retinal neurons. After applying the inhibitory cocktail, taurine enhanced delayed outward rectifier K+ channels preferentially in Off-bipolar cells, and the effect was completely blocked by the specific PKC inhibitor, GF109203X. Additionally, taurine also acted through a metabotropic pathway to suppress both L- and N-type Ca2+ channels in retinal neurons, which were insensitive to the potent GABAB receptor inhibitor, CGP55845. This study reinforces our previous finding that taurine in physiological concentrations produces a multiplicity of metabotropic effects that precisely govern the integration of signals being transmitted from the retina to the brain. PMID:23392926

  15. Analog Circuit Design Low Voltage Low Power; Short Range Wireless Front-Ends; Power Management and DC-DC

    CERN Document Server

    Roermund, Arthur; Baschirotto, Andrea

    2012-01-01

    The book contains the contribution of 18 tutorials of the 20th workshop on Advances in Analog Circuit Design.  Each part discusses a specific to-date topic on new and valuable design ideas in the area of analog circuit design. Each part is presented by six experts in that field and state of the art information is shared and overviewed. This book is number 20 in this successful series of Analog Circuit Design, providing valuable information and excellent overviews of Low-Voltage Low-Power Data Converters - Chaired by Prof. Anderea Baschirotto, University of Milan-Bicocca Short Range Wireless Front-Ends - Chaired by Prof. Arthur van Roermund, Eindhoven University of Technology Power management and DC-DC - Chaired by Prof. M. Steyaert, Katholieke University Leuven Analog Circuit Design is an essential reference source for analog circuit designers and researchers wishing to keep abreast with the latest development in the field. The tutorial coverage also makes it suitable for use in an advanced design.

  16. Critical interfaces in organic solar cells and their influence on the open-circuit voltage.

    Science.gov (United States)

    Potscavage, William J; Sharma, Asha; Kippelen, Bernard

    2009-11-17

    Organic photovoltaics, which convert sunlight into electricity with thin films of organic semiconductors, have been the subject of active research over the past 20 years. The global energy challenge has greatly increased interest in this technology in recent years. Low-temperature processing of organic small molecules from the vapor phase or of polymers from solution can confer organic semiconductors with a critical advantage over inorganic photovoltaic materials since the high-temperature processing requirements of the latter limit the range of substrates on which they can be deposited. Unfortunately, despite significant advances, the power conversion efficiency of organic solar cells remains low, with maximum values in the range of 6%. A better understanding of the physical processes that determine the efficiency of organic photovoltaic cells is crucial to enhancing their competitiveness with other thin-film technologies. Maximum values for the photocurrent can be estimated from the light-harvesting capability of the individual molecules or polymers in the device. However, a better understanding of the materials-level processes, particularly those in layer-to-layer interfaces, that determine the open-circuit voltage (V(OC)) in organic solar cells is critical and remains the subject of active research. The conventional wisdom is to use organic semiconductors with smaller band gaps to harvest a larger portion of the solar spectrum. This method is not always an effective prescription for increasing efficiency: it ignores the fact that the value of V(OC) is generally decreased in devices employing materials with smaller band gaps, as is the case with inorganic semiconductors. In this Account, we discuss the influence of the different interfaces formed in organic multilayer photovoltaic devices on the value of V(OC); we use pentacene-C(60) solar cells as a model. In particular, we use top and bottom electrodes with different work function values, finding that V(OC) is

  17. The principle of elaboration of the relay protection against short circuits between the closely placed phases of high voltage electrical line

    Directory of Open Access Journals (Sweden)

    Kiorsak M.

    2015-12-01

    Full Text Available The article is devoted to the elaboration of the principle of relay protection against short circuits between the closely placed phases of higher voltage electrical line with self-compensation, based on the six phase’s symmetrical components. It is shown that the unsymmetrical short circuits between the closely placed phases are characterized by appearance of zero and tertiary sequences of symmetrical components. This fact can be used to choose them for relay protection. The electrical basic circuits and formulas for calculation of the passive parameters of zero and tertiary filters of currents (voltages are done. It is presented the structural-functional basic circuit scheme for relay protection against short circuits between the closely placed phases of higher voltage electrical line with self-compensation.

  18. Re-evaluating the role of sterics and electronic coupling in determining the open-circuit voltage of organic solar cells

    KAUST Repository

    Graham, Kenneth

    2013-07-30

    The effects of sterics and molecular orientation on the open-circuit voltage and absorbance properties of charge-transfer states are explored in model bilayer organic photovoltaics. It is shown that the open-circuit voltage correlates linearly with the charge-transfer state energy and is not significantly influenced by electronic coupling. © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  19. On-line condition monitoring systems for high voltage circuit breakers : a collaborative research project 1997-2001

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-07-01

    A three year field project was initiated to review and evaluate the state of the art in on-line conditioning monitoring technology for a high voltage (240 kV SF6) circuit breaker located at Dorsey Converter Station. The ELF breaker is a three independent pole design which allows for three separate monitoring systems. This project involved the installation of a different type of monitoring system on each phase and incorporated many types of transducers. Each monitoring system measured the same basic parameters including contact travel, 'a' and 'b' auxiliary contacts, phase currents, coil currents, heater and pump current, plus SF6/CF4 pressure and temperature. Over the entire monitoring period the breaker was operated over 700 times at rated voltage and an additional 300 times during maintenance. Temperature conditions ranged from -35 to +30 degrees C. The use of on-line monitoring provided many valuable results and enhanced the knowledge base for the apparatus under the test. It was determined that on-line monitoring of HV circuit breakers has potential, but installation has to be considered carefully. Monitoring systems can offer improvement in the understanding of how circuit breakers work and provide input into RCM programs. However, monitoring systems themselves are subject to failure and require maintenance and attention. 2 refs., 2 tabs., 7 figs.

  20. Circuit-field coupled finite element analysis method for an electromagnetic acoustic transducer under pulsed voltage excitation

    Institute of Scientific and Technical Information of China (English)

    Hao Kuan-Sheng; Huang Song-Ling; Zhao Wei; Wang Shen

    2011-01-01

    This paper presents an analytical method for electromagnetic acoustic transducers (EMATs) under voltage excitation and considers the non-uniform distribution of the biased magnetic field. A complete model of EMATs including the non-uniform biased magnetic field, a pulsed eddy current field and the acoustic field is built up. The pulsed voltage excitation is transformed to the frequency domain by fast Fourier transformation (FFT). In terms of the time harmonic field equations of the EMAT system, the impedances of the coils under different frequencies are calculated according to the circuit-field coupling method and Poynting's theorem. Then the currents under different frequencies are calculated according to Ohm's law and the pulsed current excitation is obtained by inverse fast Fourier transformation (IFFT).Lastly, the sequentially coupled finite element method (FEM) is used to calculate the Lorentz force in the EMATs under the current excitation. An actual EMAT with a two-layer two-bundle printed circuit board (PCB) coil, a rectangular permanent magnet and an aluminium specimen is analysed. The coil impedances and the pulsed current are calculated and compared with the experimental results. Their agreement verified the validity of the proposed method. Furthermore, the influences of lift-off distances and the non-uniform static nagnetic field on the Lorentz force under pulsed voltage excitation are studied.

  1. The Semiconductor Self-Excitation System of Synchronous Generator with Fuzzy Voltage Regulator

    Directory of Open Access Journals (Sweden)

    Kutsyk, А.S.

    2014-05-01

    Full Text Available The synchronous generator’s voltage control system with the synthesized fuzzy voltage regulator is described. The synthesis of the regulator is carried out with the use of mathematical model taking into account the nonlinearity of synchronous machines and semiconductor converters in the e xcitation system. This distinguishes it from traditional excitation regulators, whose synthesis is based on the use of simplified linearized models. The mathematical modeling results allow to compare the control characteristics in the system with the proposed fuzzy voltage regulator and in the system with a traditional voltage controller.

  2. Modeling and Testing of Unbalanced Loading and Voltage Regulation

    Energy Technology Data Exchange (ETDEWEB)

    Davis, M. W.; Broadwater, R.; Hambrick, J.

    2007-07-01

    This report covers work to (1) develop and validate distribution circuit models, (2) determine optimum distributed generator operating conditions, and (3) determine distributed generation penetration limits.

  3. Voltage and Current Regulators Design of Power Converters in Islanded Microgrids based on State Feedback Decoupling

    DEFF Research Database (Denmark)

    Federico, de Bosio; de Sousa Ribeiro, Luiz Antonio; Freijedo Fernandez, Francisco Daniel

    2016-01-01

    In stand-alone microgrids based on voltage source inverters state feedback coupling between the capacitor voltage and inductor current degrades significantly the dynamics performance of voltage and current regulators. The decoupling of the controlled states is proposed, considering the limitations...... introduced by system delays. Moreover, a proportional resonant voltage controller is designed according to Nyquist criterion taking into account application requirements. Experimental tests performed in compliance with the UPS standards verify the theoretical analysis....

  4. InGaN/GaN multiple quantum well solar cells with an enhanced open-circuit voltage

    Institute of Scientific and Technical Information of China (English)

    Zhang Xiao-Bin; Wang Xiao-Liang; Xiao Hong-Ling; Yang Cui-Bai; Hou Qi-Feng; Yin Hai-Bo; Chen Hong; Wang Zhan-Guo

    2011-01-01

    In this paper, InGaN/GaN multiple quantum well solar cells (MQWSCs) with an In content of 0.15 are fabricated and studied. The short-circuit density, fill factor and open-circuit voltage (Voc) of the device are 0.7 mA/cm2, 0.40 and 2.22 V, respectively. The results exhibit a significant enhancement of Voc compared with those of InGaN-based hetero and homojunction cells. This enhancement indicates that the InGaN/GaN MQWSC offers an effective way for increasing Voc of an In-rich InxGa1-xN solar cell. The device exhibits an external quantum efficiency (EQE) of 36% (7%) at 388 nm (430 nm). The photovoltaic performance of the device can be improved by optimizing the structure of the InGaN/GaN multiple quantum well.

  5. Charged grain boundaries reduce the open-circuit voltage of polycrystalline solar cells—An analytical description

    Science.gov (United States)

    Gaury, Benoit; Haney, Paul M.

    2016-12-01

    Analytical expressions are presented for the dark current-voltage relation J(V) of a pn+ junction with positively charged columnar grain boundaries with high defect density. These expressions apply to non-depleted grains with sufficiently high bulk hole mobilities. The accuracy of the formulas is verified by direct comparison to numerical simulations. Numerical simulations further show that the dark J(V) can be used to determine the open-circuit potential Voc of an illuminated junction for a given short-circuit current density Jsc . A precise relation between the grain boundary properties and Voc is provided, advancing the understanding of the influence of grain boundaries on the efficiency of thin film polycrystalline photovoltaics like CdTe and Cu(In,Ga)Se2 .

  6. Low-Power Circuit Techniques for Low-Voltage Pipelined ADCs Based on Switched-Opamp Architecture

    Science.gov (United States)

    Ou, Hsin-Hung; Chang, Soon-Jyh; Liu, Bin-Da

    This paper proposes useful circuit structures for achieving a low-voltage/low-power pipelined ADC based on switched-opamp architecture. First, a novel unity-feedback-factor sample-and-hold which manipulates the features of switched-opamp technique is presented. Second, opamp-sharing is merged into switched-opamp structure with a proposed dual-output opamp configuration. A 0.8-V, 9-bit, 10-Msample/s pipelined ADC is designed to verify the proposed circuit. Simulation results using a 0.18-μm CMOS 1P6M process demonstrate the figure-of-merit of this pipelined ADC is only 0.71pJ/step.

  7. State Evaluation Method Based on Multiagent System for High Voltage Circuit Breaker's Mechanical Properties

    Institute of Scientific and Technical Information of China (English)

    LI Bin; LIN Xin; XU Jianyuan; QI Hongwei; ZHANG Bin

    2013-01-01

    To realize multi-signal joint diagnosis in circuit breaker's state evaluation methods,and to improve their evaluation accuracy,we proposed an intelligent evaluation model of circuit breaker mechanical properties based on multiagent system.Taking a circuit breaker which has mono-stable permanent magnetic operating mechanism as the example,its model involves four kinds of signals:auxiliary contact,operating mechanism current,travel of the contact,and mechanical vibration.Detailed analyses on the evaluation agent's architecture and the process of the system's multiagent evaluation and ratiocination were also proposed.Moreover,it is proved by three application cases that the proposed method could accurately evaluate circuit breaker status not only with normal signals,but also in certain signal failure situations; meanwhile the model has a strong self-learning ability.

  8. Comparative Study of Online Open Circuit Voltage Estimation Techniques for State of Charge Estimation of Lithium-Ion Batteries

    Directory of Open Access Journals (Sweden)

    Hicham Chaoui

    2017-04-01

    Full Text Available Online estimation techniques are extensively used to determine the parameters of various uncertain dynamic systems. In this paper, online estimation of the open-circuit voltage (OCV of lithium-ion batteries is proposed by two different adaptive filtering methods (i.e., recursive least square, RLS, and least mean square, LMS, along with an adaptive observer. The proposed techniques use the battery’s terminal voltage and current to estimate the OCV, which is correlated to the state of charge (SOC. Experimental results highlight the effectiveness of the proposed methods in online estimation at different charge/discharge conditions and temperatures. The comparative study illustrates the advantages and limitations of each online estimation method.

  9. Correlation between LUMO offset of donor/acceptor molecules to an open circuit voltage in bulk heterojunction solar cell

    Energy Technology Data Exchange (ETDEWEB)

    Mola, Genene Tessema, E-mail: mola@ukzn.ac.za [School of. Chemistry and Physics, University of Kwazulu-Natal, Pietermaritzburg Campus, Private Bag X01, Scottsville 3209 (South Africa); Abera, Newayemedhin [Addis Ababa University, Department of Physics, P.O. BOX 1176, Addis Ababa (Ethiopia)

    2014-07-15

    The correlation between the open circuit voltage and the LUMO offset of the donor and acceptor polymers in the bulkheterojunction solar cell was studied for three different thiophene derivatives. The HOMO levels of all the polymers in this investigation were chosen to be similar which results in close values of ΔE{sub DA}=E{sub HOMO}{sup D}−E{sub LUMO}{sup A}. However, the measured V{sub oc} was found to be increasing with decreasing value of the LUMO offset that exists between the donor polymer and fullerene.

  10. An Azulene-Containing Low Bandgap Small Molecule for Organic Photovoltaics with High Open-Circuit Voltage.

    Science.gov (United States)

    Chen, Yao; Zhu, Youqin; Yang, Daobin; Zhao, Suling; Zhang, Lei; Yang, Lin; Wu, Jianglin; Huang, Yan; Xu, Zheng; Lu, Zhiyun

    2016-10-01

    A simple azulene-containing squaraine dye (AzUSQ) showing bandgap of 1.38 eV and hole mobility up to 1.25×10(-4)  cm(2)  V(-1)  s(-1) was synthesized. With its low bandgap, an organic photovoltaic (OPV) device based on it has been made that exhibits an impressive open-circuit voltages (Voc ) of 0.80 V. Hence, azulene might be a promising structural unit to construct OPV materials with simultaneous low bandgap, high hole mobility and high Voc .

  11. Hysteresis observed in quasi open-circuit voltage measurements of lithium insertion in hydrogen-containing carbons

    Energy Technology Data Exchange (ETDEWEB)

    Zheng Tao; Dahn, J.R. [Dalhousie Univ., Halifax, NS (Canada). Dept. of Physics

    1997-10-01

    High capacities with large hysteresis were observed during lithium insertion in hydrogen-containing carbons heated at temperatures near 700 C. Quasi open-circuit voltage (OCV) measurements were used to study these materials. Using a simple model developed previously, we can qualitatively model the result of the OCV measurement. It is believed that the lithium atoms bind near aromatic hydrogen at edge of each graphene layer in the materials. This activated process involves a carbon-carbon bonding change from (sp){sup 2} to (sp){sup 3} leading to large hysteresis during lithium insertion. (orig.)

  12. Low voltage logic circuits exploiting gate level dynamic body biasing in 28 nm UTBB FD-SOI

    Science.gov (United States)

    Taco, Ramiro; Levi, Itamar; Lanuzza, Marco; Fish, Alexander

    2016-03-01

    In this paper, the recently proposed gate level body bias (GLBB) technique is evaluated for low voltage logic design in state-of-the-art 28 nm ultra-thin body and box (UTBB) fully-depleted silicon-on-insulator (FD-SOI) technology. The inherent benefits of the low-granularity body-bias control, provided by the GLBB approach, are emphasized by the efficiency of forward body bias (FBB) in the FD-SOI technology. In addition, the possibility to integrate PMOS and NMOS devices into a single common well configuration allows significant area reduction, as compared to an equivalent triple well implementation. Some arithmetic circuits were designed using GLBB approach and compared to their conventional CMOS and DTMOS counterparts under different running conditions at low voltage regime. Simulation results shows that, for 300 mV of supply voltage, a 4 × 4-bit GLBB Baugh Wooley multiplier allows performance improvement of about 30% and area reduction of about 35%, while maintaining low energy consumption as compared to the conventional CMOS ⧹ DTMOS solutions. Performance and energy benefits are maintained over a wide range of process-voltage-temperature (PVT) variations.

  13. Transcriptional regulation of voltage-gated Ca(2+) channels.

    Science.gov (United States)

    González-Ramírez, Ricardo; Felix, Ricardo

    2017-03-31

    The transcriptional regulation of voltage-gated Ca(2+) (CaV ) channels is an emerging research area that promises to improve our understanding of how many relevant physiological events are shaped in the central nervous system, the skeletal muscle, and other tissues. Interestingly, a picture of how transcription of CaV channel subunit genes is controlled is evolving with the identification of the promoter regions required for tissue-specific expression, and the identification of transcription factors that control their expression. These promoters share several characteristics that include multiple transcriptional start sites, lack of a TATA box, and the presence of elements conferring tissue-selective expression. Likewise, changes in CaV channel expression occur throughout development, following ischemia, seizures, or chronic drug administration. This review focuses on insights achieved regarding the control of CaV channel gene expression. To further understand the complexities of expression and to increase the possibilities of detecting CaV channel alterations causing human disease, a deeper knowledge on the structure of the 5' upstream regions of the genes encoding these remarkable proteins will be necessary. This article is protected by copyright. All rights reserved.

  14. Circuits protection against interferences in high voltage substations; Protecao de circuitos contra interferencias em subestacoes

    Energy Technology Data Exchange (ETDEWEB)

    Hamada, Massayuki [Consultas e Aplicacoes de Engenharia Eletrica Ltda. (CAEEL) (Brazil)

    1989-12-01

    This paper makes a brief analysis of the different phenomena which may cause electromagnetic interference in high voltage substations and suggests adequate solutions to the problem according to the different events that may occur. 5 refs., 1 fig.

  15. High performance dc-dc conversion with voltage multipliers. [using transformerless capacitor diode circuit

    Science.gov (United States)

    Harrigill, W. T., Jr.; Myers, I. T.

    1974-01-01

    An experimental 100W 1000V dc-dc converter using a capacitor diode voltage multipler (CDVM) with a nominal frequency of 100 kHz is studied. A component weight of about 1 kg/kW was obtained. Design equations for current, output -ripple and -power, efficiency and output voltage are derived. Agreement between experimental results and calculations is fairly good except for ripple.

  16. Distributed Control to Ensure Proportional Load Sharing and Improve Voltage Regulation in Low-Voltage DC Microgrids

    DEFF Research Database (Denmark)

    Anand, Sandeep; G. Fernandes, Baylon; Guerrero, Josep M.

    2013-01-01

    DC microgrids are gaining popularity due to high efficiency, high reliability, and easy interconnection of renewable sources as compared to the ac system. Control objectives of dc microgrid are: 1) to ensure equal load sharing (in per unit) among sources; and 2) to maintain low-voltage regulation...

  17. Principle Analysis and Test of M-type Voltage Regulator%M型电压调节器的原理分析与检测

    Institute of Scientific and Technical Information of China (English)

    安明华

    2012-01-01

    The development of auto generator voltage regulator has gone through four stages: mechanical contact, transistor, integrated circuit, electronic control. The principle and test method of integrated circuit voltage regulator are analyzed with the example of DENSO M-type regulator.%汽车发电机电压调节器经历了机械触点式、晶体管式、集成电路式、微机控制式的发展。本文以电装M型电压调节器为例。分析集成电路电压调节器的原理及检测方法。

  18. Comparative Performance Analysis of XOR-XNOR Function Based High-Speed CMOS Full Adder Circuits For Low Voltage VLSI Design

    Directory of Open Access Journals (Sweden)

    Sudarshan Tiwari

    2012-05-01

    Full Text Available This paper presents comparative study of high-speed, low-power and low voltage full adder circuits. Our approach is based on XOR-XNOR design full adder circuits in a single unit. A low power and high performance 9T full adder cell using a design style called “XOR (3T” is discussed. The designed circuit commands a high degree of regularity and symmetric higher density than the conventional CMOS design style as well as it lowers power consumption by using XOR (3T logic circuits. Gate Diffusion Input (GDI technique of low-power digital combinatorial circuit design is also described. This technique helps inreducing the power consumption and the area of digital circuits while maintaining low complexity of logic design. This paper analyses, evaluates and compares the performance of various adder circuits. Severalsimulations conducted using different voltage supplies, load capacitors and temperature variation demonstrate the superiority of the XOR (3T based full adder designs in term of delay, power and powerdelay product (PDP compared to the other full adder circuits. Simulation results illustrate the superiority of the designed adder circuits against the conventional CMOS, TG and Hybrid full adder circuits in terms of power, delay and power delay product (PDP.

  19. Design of wide output voltage AC-DC power supply based on buck-boost circuit%基于Buck-Boost电路的宽输出电压AC-DC电源设计

    Institute of Scientific and Technical Information of China (English)

    徐文城; 刘尧; 王秀荣

    2012-01-01

    设计了一种宽输出电压的AC DC开关电源,其主要特征是输出电压可以在较大范围内任意调节,解决了传统的开关电源只能输出几个特定电压值的问题.该设计的核心是反激变换电路和Buck-Boost电路.分析了这两种电路的工作原理及其应用,并且给出了具体的设计.实验表明,设计的电源能较好地实现了输出电压的宽范围调节.%AC-DC switching power supply with a wide range voltage output was designed. Its main feature is that the output voltage can be adjusted in a wide range. The problem that the traditional switching power supplies only have few specific voltage outputs is solved in the design. The flyback convert circuit and Buck-Boost circuit are the cores of the design. The working principle and applications of these two circuits are analyzed. The concrete design is given in this paper. The experiments show that a wide range regulation of the output voltage has been more successfully achieved in the design of the power supply.

  20. Dynamic voltage regulation and power export in a distribution system using distributed generation

    Institute of Scientific and Technical Information of China (English)

    Aamir HANIF; Muhammad Ahmed CHOUDHRY

    2009-01-01

    The major aim of power quality (PQ) enhancing techniques is to maintain a specified voltage magnitude at a desired frequency for sensitive loads irrespective of faults on the power distribution network. The dynamic voltage restorer (DVR) is a device used to mitigate voltage sags to regulate load voltage. This paper presents a mathematical model for leading series voltage injection to mitigate sags thereby achieving the improvement of the utility power factor as well as power sharing between the DVR and utility. The power sharing will be as per requirement to compensate the sags considering the available distributed generation (DG). The approach of mitigating voltage sags using the concept of leading series voltage injection is suitable for those locations where phase shift in the voltage will not cause any problem. The MATLAB/SIMULINK SimPowerSystem toolbox has been used to obtain simulation results to verify the proposed mathematical model.

  1. Development of Thin Film Amorphous Silicon Tandem Junction Based Photocathodes Providing High Open-Circuit Voltages for Hydrogen Production

    Directory of Open Access Journals (Sweden)

    F. Urbain

    2014-01-01

    Full Text Available Hydrogenated amorphous silicon thin film tandem solar cells (a-Si:H/a-Si:H have been developed with focus on high open-circuit voltages for the direct application as photocathodes in photoelectrochemical water splitting devices. By temperature variation during deposition of the intrinsic a-Si:H absorber layers the band gap energy of a-Si:H absorber layers, correlating with the hydrogen content of the material, can be adjusted and combined in a way that a-Si:H/a-Si:H tandem solar cells provide open-circuit voltages up to 1.87 V. The applicability of the tandem solar cells as photocathodes was investigated in a photoelectrochemical cell (PEC measurement set-up. With platinum as a catalyst, the a-Si:H/a-Si:H based photocathodes exhibit a high photocurrent onset potential of 1.76 V versus the reversible hydrogen electrode (RHE and a photocurrent of 5.3 mA/cm2 at 0 V versus RHE (under halogen lamp illumination. Our results provide evidence that a direct application of thin film silicon based photocathodes fulfills the main thermodynamic requirements to generate hydrogen. Furthermore, the presented approach may provide an efficient and low-cost route to solar hydrogen production.

  2. Improving open-circuit voltage in DSSCs using Cu-doped TiO{sub 2} as a semiconductor

    Energy Technology Data Exchange (ETDEWEB)

    Navas, J.; Fernandez-Lorenzo, C.; Aguilar, T.; Alcantara, R.; Martin-Calleja, J. [Physical Chemistry Department, Science Faculty, University of Cadiz, Campus Universitario de Puerto Real, Cadiz (Spain)

    2012-02-15

    TiO{sub 2} doping has been widely used in photocatalysis and photovoltaic cells to improve the performance of this semiconductor. This paper studies the use of copper as a dopant in TiO{sub 2} in dye-sensitized solar cells (DSSC), analysing the effect on the photovoltaic properties of the cells of different concentrations of copper incorporated into the semiconductor. The copper-doped TiO{sub 2} semiconductor was characterized with several instrumental techniques, including X-ray diffraction (XRD), inductively coupled plasma atomic emission spectroscopy (ICP-AES), scanning transmission electron microscopy (STEM), and UV-Vis spectroscopy in order to know its structure, composition and band gap energies with different concentrations of the dopant. An analysis was also performed of the variations in open-circuit voltage depending on the concentration of copper. This showed that the presence of copper in DSSCs made with a standard configuration - using a ruthenium complex (N3) as a dye and the redox pair I{sup -}/I{sub 3}{sup -} as the electrolyte with 3-methoxypropionitrile as a solvent - leads to improvements of up to 10% in the open-circuit voltage of DSSCs. (Copyright copyright 2012 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  3. SEMICONDUCTOR INTEGRATED CIRCUITS A low-voltage sense amplifier for high-performance embedded flash memory

    Science.gov (United States)

    Jiang, Liu; Xueqiang, Wang; Qin, Wang; Dong, Wu; Zhigang, Zhang; Liyang, Pan; Ming, Liu

    2010-10-01

    This paper presents a sense amplifier scheme for low-voltage embedded flash (eFlash) memory applications. The topology of the sense amplifier is based on current mode comparison. Moreover, an offset-voltage elimination technique is employed to improve the sensing performance under a small memory cell current. The proposed sense amplifier is designed based on a GSMC 130 nm eFlash process, and the sense time is 0.43 ns at 1.5 V, corresponding to a 46% improvement over the conventional technologies.

  4. Improving Transient Recovery voltage of circuit breaker using Fault Current Limiter

    Directory of Open Access Journals (Sweden)

    Amir Heidary

    2012-12-01

    Full Text Available This study investigates influence of Fault Current Limiter (FCL on short-circuits current level of substation bus bar splitter circuit breaker and its TRV. An approach for TRV evaluation is developed and applied for proposed power system as shown in this study. FCL circuit is connected to the power system in order to limit TRV. The limiter circuit consists of two equal windings which are turned around unique magnetic core. One of the windings is connected in series with the power system network and the other is connected to the network via series capacitor and power electronic switches. During normal operating condition, both tyristors are in on state and current of the primary and secondary windings are equal. This causes zero impedance of the limiter. During fault, faults current cause the power electronic switch to turn off which increases the limiter impedance. By increasing the limiter impedance, amplitude of TRV decreases substantially. The novel method presented in this study is a cheap and successful scheme.

  5. Approach for electrodynamic force for compensation in low voltage circuit breaker WP 630-1.2 type

    Institute of Scientific and Technical Information of China (English)

    LU Na; XU L.J.; Miedzi(n)ski B.

    2007-01-01

    Undesirable repulsive force between contact members due to both a current path shrink near a real contact area and/or so-called pinch effect is particularly onerous for power switch applications, and results in either contact floating or bouncing which are associated with an electric arc following contact welding. This problem is of great importance for any circuit breaker especially for compact low voltage vacuum circuit breakers. To avoid contact floating at closure and during any inrush current under short circuit conditions, the electrodynamic repulsive force can be employed successfully if we use a special compensation system flexibly combined with the contact itself. However to select and design the compensation system properly, its efficiency has to be known. This paper presents an approach to obtain the electrodynamic force value depending on different shaped (rectangular,square, circle and arch) copper plates used in the compensator by using ANSYS for current values 40 kA RMS. Curve-fitting was done according to the calculating results, the optimization designing of compensation unit is based on them.

  6. Fault Modeling and Testing for Analog Circuits in Complex Space Based on Supply Current and Output Voltage

    Directory of Open Access Journals (Sweden)

    Hongzhi Hu

    2015-01-01

    Full Text Available This paper deals with the modeling of fault for analog circuits. A two-dimensional (2D fault model is first proposed based on collaborative analysis of supply current and output voltage. This model is a family of circle loci on the complex plane, and it simplifies greatly the algorithms for test point selection and potential fault simulations, which are primary difficulties in fault diagnosis of analog circuits. Furthermore, in order to reduce the difficulty of fault location, an improved fault model in three-dimensional (3D complex space is proposed, which achieves a far better fault detection ratio (FDR against measurement error and parametric tolerance. To address the problem of fault masking in both 2D and 3D fault models, this paper proposes an effective design for testability (DFT method. By adding redundant bypassing-components in the circuit under test (CUT, this method achieves excellent fault isolation ratio (FIR in ambiguity group isolation. The efficacy of the proposed model and testing method is validated through experimental results provided in this paper.

  7. Comparison of resonant current regulators for DFIG during grid voltage distortion

    Institute of Scientific and Technical Information of China (English)

    Yi-peng SONG; Heng NIAN

    2013-01-01

    We investigate two different kinds of resonant current regulators for a doubly fed induction generator (DFIG) under distorted grid voltage conditions:proportional integral resonant (PIR) regulator with traditional resonant part and vector propor-tional integral (VPI) regulator with VPI resonant part. Based on the mathematical model of DFIG under distorted grid voltage, the transfer function and frequency response characteristics of the two current regulators are analyzed and compared. The superiority of the VPI current regulator over the PIR regulator is pointed out, and the influence of discretization methods on the performance of the resonant current regulator is studied. All the results are validated by MATLAB simulation and experiments.

  8. 电容降压式电路的设计原理%Design principle of capacitor-depressing-voltage circuit

    Institute of Scientific and Technical Information of China (English)

    杨海明; 杨国志; 李悦; 舒德泉

    2013-01-01

    Compared with the power transformer,capacitor-depressing-voltage circuit has a small size,economical and reliable power,high efficiency,so is often used.By analysis the circuit theory of capacitor-depressing-voltage DC power supply circuit under sinusoidal AC,this paper presented the three circuit schematic of capacitor-depressing-voltage DC power supply circuit,and summed up the conditions of use,component requirements,design parameters and notes about capacitor-depressing-voltage DC power supply circuit.%与电源变压器降压相比,电容降压具有电源体积小、经济、可靠、效率高等优点,所以常被使用.通过分析电容降压式直流电源电路在正弦交流电下的电路原理,给出三种电容降压式直流电源电路的原理图,并总结出设计电容降压式直流电源的使用条件、元器件要求、设计参数和注意事项.

  9. Circuits Regulating Pleasure and Happiness—Mechanisms of Depression

    Science.gov (United States)

    Loonen, Anton J. M.; Ivanova, Svetlana A.

    2016-01-01

    According to our model of the regulation of appetitive-searching vs. distress-avoiding behaviors, the motivation to display these essential conducts is regulated by two parallel cortico-striato-thalamo-cortical, re-entry circuits, including the core and the shell parts of the nucleus accumbens, respectively. An entire series of basal ganglia, running from the caudate nucleus on one side, to the centromedial amygdala on the other side, controls the intensity of these reward-seeking and misery-fleeing behaviors by stimulating the activity of the (pre)frontal and limbic cortices. Hyperactive motivation to display behavior that potentially results in reward induces feelings of hankering (relief leads to pleasure). Hyperactive motivation to exhibit behavior related to avoidance of misery results in dysphoria (relief leads to happiness). These two systems collaborate in a reciprocal fashion. In clinical depression, a mismatch exists between the activities of these two circuits: the balance is shifted to the misery-avoiding side. Five theories have been developed to explain the mechanism of depressive mood disorders, including the monoamine, biorhythm, neuro-endocrine, neuro-immune, and kindling/neuroplasticity theories. This paper describes these theories in relationship to the model (described above) of the regulation of reward-seeking vs. misery-avoiding behaviors. Chronic stress that leads to structural changes may induce the mismatch between the two systems. This mismatch leads to lack of pleasure, low energy, and indecisiveness, on one hand, and dysphoria, continuous worrying, and negative expectations on the other hand. The neuroplastic effects of monoamines, cortisol, and cytokines may mediate the induction of these structural alterations. Long-term exposure to stressful situations (particularly experienced during childhood) may lead to increased susceptibility for developing this condition. This hypothesis opens up the possibility of treating depression with

  10. Circuits regulating pleasure and happiness – mechanisms of depression

    Directory of Open Access Journals (Sweden)

    Anton J.M. Loonen

    2016-11-01

    Full Text Available According to our model of the regulation of appetitive-searching versus distress-avoiding behaviors, the motivation to display these essential conducts is regulated by two parallel cortico-striato-thalamo-cortical, re-entry circuits, including the core and the shell parts of the nucleus accumbens, respectively. An entire series of basal ganglia, running from the caudate nucleus on one side, to the centromedial amygdala on the other side, controls the intensity of these reward-seeking and misery-fleeing behaviors by stimulating the activity of the (prefrontal and limbic cortices. Hyperactive motivation to display behavior that potentially results in reward induces feelings of hankering (relief leads to pleasure. Hyperactive motivation to exhibit behavior related to avoidance of misery results in dysphoria (relief leads to happiness. These two systems collaborate in a reciprocal fashion. In clinical depression, a mismatch exists between the activities of these two circuits: the balance is shifted to the misery-avoiding side. Five theories have been developed to explain the mechanism of depressive mood disorders, including the monoamine, biorhythm, neuro-endocrine, neuro-immune, and kindling/neuroplasticity theories. This paper describes these theories in relationship to the model (described above of the regulation of reward-seeking versus misery-avoiding behaviors. Chronic stress that leads to structural changes may induce the mismatch between the two systems. This mismatch leads to lack of pleasure, low energy, and indecisiveness, on one hand, and dysphoria, continuous worrying, and negative expectations on the other hand. The neuroplastic effects of monoamines, cortisol, and cytokines may mediate the induction of these structural alterations. Long-term exposure to stressful situations (particularly experienced during childhood may lead to increased susceptibility for developing this condition. This hypothesis opens up the possibility of treating

  11. Power flow control and voltage stability limit: regulating transformer versus UPFC

    Energy Technology Data Exchange (ETDEWEB)

    Haque, M.H. [Nanyang Technological Univ., Center for Advanced Power Electronics, Nanyang (Singapore)

    2004-05-01

    Power flow through an AC transmission line can be controlled by injecting an adjustable compensating voltage in series with the line. This paper evaluates and compares the power flow control ranges of a simple system obtained by injecting an adjustable series compensating voltage produced by a regulating transformer and unified power flow controller. The static voltage stability limits of the system with a regulating transformer and unified power flow controller are also determined and compared. In evaluating the power flow control ranges and voltage stability limits, the transmission line of the system is modelled in four different ways. The results obtained for various line models are also compared. (Author)

  12. An Internal ALD-Based High Voltage Divider and Signal Circuit for MCP-based Photodetectors

    Energy Technology Data Exchange (ETDEWEB)

    Adams, Bernhard W.; Elagin, Andrey; Elam, Jeffrey W.; Frisch, Henry J.; Genat, Jean-Francois; Gregar, Joseph S.; Mane, Anil U.; Minot, Michael J.; Northrup, Richard; Obaid, Razib; Oberla, Eric; Alexander, Vostrikov; Wetstein, Matthew

    2015-04-21

    We describe a pin-less design for the high voltage (HV) resistive divider of the all-glass LAPPD (TM) 8 in,square thin photodetector module. The divider, which distributes high voltage applied to the photocathode to the two micro-channel plates (MCPs) that constitute the amplification stage, is comprised of the two MCPs and three glass mechanical spacers, each of which is coated with a resistive layer using atomic layer deposition (ALD). The three glass grid spacers and the two MCPs form a continuous resistive path between cathode and anode, with the voltages across the MCPs and the spacers determined by the resistance of each. High voltage is applied on an external tab on the top glass window that connects to the photocathode through the metal seal. The DC ground is supplied by microstrips on the bottom glass plate that form the high-bandwidth anode. The microstrips exit the package through the glass-frit seal of the anode base-plate and the package sidewall. The divider is thus completely internal, with no HV pins penetrating the low-profile flat glass package. Measurements of the performance of the divider are presented for the 8 in.-square MCP and spacer package in a custom test fixture and for an assembled externally pumped LAPPD (TM) prototype with an aluminum photocathode. (C) 2015 Elsevier B.V. All rights reserved.

  13. Complementary circuits based on solution processed low-voltage organic field-effect transistors

    NARCIS (Netherlands)

    Ball, James M.; Wöbkenberg, Paul H.; Kooistra, Floris B.; Hummelen, Jan C.; Leeuw, Dago M. de; Bradley, Donal D.C.; Anthopoulos, Thomas D.

    2009-01-01

    The field of organic electronics is advancing quickly towards ultra low-cost, low-end applications and is expected to provide the necessary technology required for flexible/printed electronics. Here we address the need for solution processed low-voltage complementary logic in order to reduce power c

  14. Circuito equivalente de un transformador con regulación Equivalent circuit of a regulating transformer

    Directory of Open Access Journals (Sweden)

    Juan A Martínez-Velasco

    2011-06-01

    Full Text Available Este artículo presenta una metodología para la obtención y utilización del circuito equivalente de un transformador con regulación en el que es posible variar su relación de transformación. Este aspecto está insuficientemente tratado en la mayoría de libros de texto actuales en los que el circuito de un transformador con regulación se presenta de forma poco justificada. Este documento muestra cómo obtener el circuito equivalente del transformador y cómo aplicarlo utilizando tanto valores reales como valores por unidad (pu. El tratamiento con valores por unidad se puede realizar seleccionando los valores base de forma arbitraria, lo que supone una ventaja evidente cuando se trata de determinar alguna de las tensiones nominales del transformador en estudio. Aunque el objetivo del artículo es el de presentar un método para transformadores con regulación, el método es también válido para transformadores con relación de transformación constante en los que se tenga que determinar alguna de sus tensiones nominales. El artículo incluye dos ejemplos con campos de aplicación muy distintos que servirán para ilustrar las ventajas del método propuesto.This paper presents a methodology aimed at obtaining and applying the equivalent circuit of a regulating transformer, whose turn ratio can be varied. This aspect is insufficiently treated in most current textbooks in which the equivalent circuit of a tapped transformer is not well justified. This document shows how to obtain the equivalent circuit of the transformer and how to apply it using either physical quantities or per unit (pu quantities. The usage of per unit values can be performed by selecting the base quantities in an arbitrary manner, which is an obvious advantage when one of the rated voltages must be estimated. Although the goal of the paper is to develop a method for regulating transformers (e.g., under load tap changers, ULTC, it can be applied to transformers with a

  15. Efficient Low Voltage Amplification Using Self Starting Voltage Regulator for Storage System

    Directory of Open Access Journals (Sweden)

    Haslinah Binti Mohd Nasir

    2014-10-01

    Full Text Available This paper presents a storage system design based on energy harvesting to achieve batteryless for Wireless Sensor Network (WSN application. The storage system is part of the Wireless Sensor Energy Harvesting to store and amplify the energy harvested from the surroundings. Finding a new sources of renewable energy has becomes a fashionable among researchers nowadays in particular harvesting the energy from the surrounding. However the challenge raised is to boost up the energy that known are very low. Thus the proposed method must be consumes very little power and suitable for ambient environmental sources such as vibration, wind and RF energy and be able to boost up the energy for storage system. The output of the harvested voltage is insufficient for most applications, therefore the system will boost up the input voltage level using DC to DC converter topology to higher dc voltage.The DC to DC converter shall be designed to suit the types of storage required. The output voltage of this DC converter should be sufficient to charge either capacitor or supercapacitor that will be use in this system as the energy storage system. The supercapacitor will provide power to energize any system such as in this case wireless sensor network[1]. In the case of wireless sensor network for example, the node would require the energy during transmitting and receiving data only whereas during standby mode or sleep mode, the amount of energy required would be very small[2]. Therefore the storage system will make use of this standby time or sleep mode of the sensor node to store as much energy as possible. The presented DC to DC converter in this paper has high efficiency upto 85.4% with input voltage between range 300mV to 600mV.

  16. Design of CMOS bandgap voltage reference circuit with high PSR%一种高PSR CMOS带隙基准电路设计

    Institute of Scientific and Technical Information of China (English)

    贺志伟; 姜岩峰

    2014-01-01

    为了降低芯片电路功耗,电源电压需要不断的减小,这将导致电源噪声对基准电压产生严重影响。为此针对这一问题进行相关研究,采用SMIC 0.18μm工艺,设计出一种低功耗、低温度系数的高PSR带隙基准电压源。仿真结果表明,该设计带隙基准源的PSR在50 kHz与100 kHz分别为-65.13 dB和-53.85 dB;在2~6 V电源电压下,工作电流为30μA,温度系数为30.38 ppm/℃,电压调整率为71.47μV/V。该带隙基准适用于在低功耗高PSR性能需求的LDOs电路中应用。%The power supply voltage needs to be constantly decreased to meet the requirement of reducing the low-power consumption of IC,but it may lead to the negative impact of power supply noise on the reference voltage. A low-power consump-tion bandgap voltage reference with high PSR (power supply rejection) and low-temperature coefficent was design based on in SMIC0.18μm process. The simulation results show that the PSR of the bandgap reference source is -65.13 dB at 50 kHz and -53.85 dB at 100 kHz respectively;at 2~6 V supply voltage,the supply current is 30 μA,the temperature coefficient is 30.38 ppm/℃,and the voltage regulation rate is 71.47 μV/V. The bandgap voltage reference is suitable for LDOs circuit which has the requirements of low-power consumption and high PSR.

  17. Robust Sequential Circuits Design Technique for Low Voltage and High Noise Scenarios

    Directory of Open Access Journals (Sweden)

    Garcia-Leyva Lancelot

    2016-01-01

    In this paper we introduce an innovative input and output data redundancy principle for sequential block circuits, the responsible to keep the state of the system, showing its efficiency in front of other robust technique approaches. The methodology is totally different from the Von Neumann approaches, because element are not replicated N times, but instead, they check the coherence of redundant input data no allowing data propagation in case of discrepancy. This mechanism does not require voting devices.

  18. Statistics of voltage drop in distribution circuits: a dynamic programming approach

    Energy Technology Data Exchange (ETDEWEB)

    Turitsyn, Konstantin S [Los Alamos National Laboratory

    2010-01-01

    We analyze a power distribution line with high penetration of distributed generation and strong variations of power consumption and generation levels. In the presence of uncertainty the statistical description of the system is required to assess the risks of power outages. In order to find the probability of exceeding the constraints for voltage levels we introduce the probability distribution of maximal voltage drop and propose an algorithm for finding this distribution. The algorithm is based on the assumption of random but statistically independent distribution of loads on buses. Linear complexity in the number of buses is achieved through the dynamic programming technique. We illustrate the performance of the algorithm by analyzing a simple 4-bus system with high variations of load levels.

  19. Transparent Pixel Circuit with Threshold Voltage Compensation Using ZnO Thin-Film Transistors for Active-Matrix Organic Light Emitting Diode Displays

    Science.gov (United States)

    Yang, Ik-Seok; Kwon, Oh-Kyong

    2009-03-01

    A transparent pixel circuit with a threshold voltage compensating scheme using ZnO thin-film transistors (TFTs) for active-matrix organic light emitting diode (AMOLED) displays is proposed. This circuit consists of five n-type ZnO TFTs and two capacitors and can compensate for the threshold voltage variation of ZnO TFTs in real time. From simulation results, the maximum deviation of the emission current of the pixel circuit with a threshold voltage variation of ±1 V is determined to be less than 10 nA. From measurement results, it is verified that the maximum deviation of measured emission currents with measurement position in a glass substrate is less than 15 nA in a higher current range, and the deviation of emission current with time is less than 3%.

  20. Note: Wide-range and high-resolution on-chip delay measurement circuit with low supply-voltage sensitivity for SoC applications

    Science.gov (United States)

    Sheng, Duo; Hung, Yu-Chan

    2016-11-01

    This paper presents an on-chip delay measurement (OCDM) circuit with a wide delay-measurement range, a high delay-measurement resolution and low supply-voltage sensitivity for efficient detection, and diagnosis in the high-performance system-on-chip (SoC). The proposed cascade-stage measurement structure can simultaneously achieve a delay-measurement range of several nanoseconds and a quantization resolution of several picoseconds. The proposed delay-measurement circuit has a high immunity to supply voltage variations without any additional calibration or self-biasing circuit. The delay-measurement range is 5.25 ns with 6 ps resolution; and the average delay resolution variation is 0.41% with ±10% supply voltage variations.

  1. Study of DC Circuit Breaker of H2-N2 Mixture Gas for High Voltage

    Science.gov (United States)

    Shiba, Yuji; Morishita, Yukinaga; Kaneko, Shuhei; Okabe, Shigemitsu; Mizoguchi, Hitoshi; Yanabu, Satoru

    Global warming caused by CO2 etc. is a field where the concern is very high. Especially, automobile emissions are problem for it. Therefore, the hybrid car is widely development and used recently. Hybrid car used electric power and gasoline. So, the car reduces CO2. Hybrid car has engine and motor. To rotate the motor, hybrid car has battery. This battery is large capacity. Therefore, the relay should interrupt high DC current for the switch of the motor and the engine. So, hybrid car used hydrogen gas filling relay We studied interruption test for the research of a basic characteristic of hydrogen gas. DC current has not current zero point. So, it is necessary to make the current zero by high arc voltage and forcible current zero point. The loss coefficient and arc voltage of hydrogen is high. Therefore, we studied interruption test for used high arc voltage. We studied interruption test and dielectric breakdown test of air, pure Hydrogen, and Hydrogen- nitrogen mixture gas. As a result, we realized H2-N2(80%-20%) is the best gas.

  2. [PhysioFlex: a target-controlled self-regulating closed-circuit inhalation anesthesia regulator].

    Science.gov (United States)

    Nathan, N; Sperandio, M; Erdmann, W; Westerkamp, B; Van Dijk, G; Scherpereel, P; Feiss, P

    1997-01-01

    Physi Flex is the first commercially available apparatus capable for quantitative, or self-regulating target controlled inhalational anaesthesia, with a totally closed circuit, in adults and children. The fresh gas supply to the circuit is intermittent, automatically regulated by continuous monitoring of the volume and composition of the gas mixture in the breathing circuit. The circle system includes, instead of the two conventional one way valves, a blower creating a continuous unidirectional flow at 70 L.min-1. In addition to the CO2-absorber it contains an absorber with carbon, absorbing the anaesthetic vapour when switched into the circuit. The ventilator consists of four ventilating chambers, each one with a membrane separating the patient and the motor compartments. The displacement of the membranes generates and measures the tidal volume. Automatic ventilation is achieved by electric valves and motor gas, and manual ventilation using a bag. Spontaneous ventilation is also possible. The machine is operated via a computer with selects the number of ventilating chambers (one, two or four), and the tidal volume between 50 and 2,000 mL, depending on age, gender and weight of the patient. The computer maintains the gas volume and the gas and vapour concentrations at their preset values. The O2-flow and consumption, the N2O flow and uptake, FICO2 and FETCO2, FI and FET of the volatile anaesthetic, all other important data are displayed in a numerical and graphical form on a color screen and registered for a delayed analysis. The end tidal concentration of the volatile anaesthetic drives a stepmotor with a syringe containing the selected volatile anaesthetic agent with is directly injected into the breathing circuit where it is vaporized. Therefore the concentration of the anaesthetic vapour can be instantaneously increased with this injector at induction and lowered at end of anaesthesia with the carbon absorber, and the fresh gas consumption is significantly

  3. Modular high voltage power supply for chemical analysis

    Science.gov (United States)

    Stamps, James F.; Yee, Daniel D.

    2008-07-15

    A high voltage power supply for use in a system such as a microfluidics system, uses a DC-DC converter in parallel with a voltage-controlled resistor. A feedback circuit provides a control signal for the DC-DC converter and voltage-controlled resistor so as to regulate the output voltage of the high voltage power supply, as well as, to sink or source current from the high voltage supply.

  4. Voltage Regulation and Line Loss Minimization of Loop Distribution Systems Using UPFC

    Science.gov (United States)

    Sayed, Mahmoud A.; Takeshita, Takaharu

    This paper presents a new method for achieving line loss minimization and voltage regulation in the loop distribution systems, simultaneously. First, mathematical analysis of the line loss minimum conditions in the loop distribution systems is presented. Then, load voltage regulation is applied in the loop distribution system under line loss minimum condition. Reference angle of the desired load voltage is the main factor that can be used to minimize total line loss during load voltage control. In order to achieve these two objectives simultaneously, the UPFC (unified power flow controller), a typical FACTS (flexible AC transmission systems) device, that is capable of instantaneous control of transmission and distribution power flow, is used. Also, the UPFC control scheme to regulate the load voltage under line loss minimization is presented. The effectiveness of the proposed control scheme has been verified experimentally using laboratory prototype in a 200V, 6kVA system.

  5. Evidence of Gate Voltage Oscillations during Short Circuit of Commercial 1.7 kV/ 1 kA IGBT Power Modules

    DEFF Research Database (Denmark)

    Reigosa, Paula Diaz; Wu, Rui; Iannuzzo, Francesco;

    2015-01-01

    This paper analyzes the evidence of critical gate voltage oscillations in 1.7 kV/1 kA Insulated-Gate Bipolar Transistor (IGBT) power modules under short circuit conditions. A 6 kA/1.1 kV Non-Destructive Test (NDT) set up for repeatable short circuit tests has been built with a 40 nH stray inducta...

  6. Evidence of Gate Voltage Oscillations during Short Circuit of Commercial 1.7 kV/ 1 kA IGBT Power Modules

    DEFF Research Database (Denmark)

    Reigosa, Paula Diaz; Wu, Rui; Iannuzzo, Francesco

    2015-01-01

    This paper analyzes the evidence of critical gate voltage oscillations in 1.7 kV/1 kA Insulated-Gate Bipolar Transistor (IGBT) power modules under short circuit conditions. A 6 kA/1.1 kV Non-Destructive Test (NDT) set up for repeatable short circuit tests has been built with a 40 nH stray inducta...

  7. Enhanced Open-Circuit Voltage in Visible Quantum Dot Photovoltaics by Engineering of Carrier-Collecting Electrodes

    KAUST Repository

    Wang, Xihua

    2011-10-26

    Colloidal quantum dots (CQDs) enable multijunction solar cells using a single material programmed using the quantum size effect. Here we report the systematic engineering of 1.6 eV PbS CQD solar cells, optimal as the front cell responsible for visible-wavelength harvesting in tandem photovoltaics. We rationally optimize each of the device\\'s collecting electrodes-the heterointerface with electron-accepting TiO2 and the deep-work-function hole-collecting MoO3 for ohmic contact-for maximum efficiency. We report an open-circuit voltage of 0.70 V, the highest observed in a colloidal quantum dot solar cell operating at room temperature. We report an AM1.5 solar power conversion efficiency of 3.5%, the highest observed in >1.5 eV bandgap CQD PV device. © 2011 American Chemical Society.

  8. Three-dimensional modelling of electric-arc development in a low-voltage circuit-breaker

    Energy Technology Data Exchange (ETDEWEB)

    Piqueras, L.; Henry, D.; Jeandel, D.; Scott, J. [Laboratoire de Mecanique des Fluides et d' Acoustique, CNRS/Universite de Lyon, Ecole Centrale de Lyon/Universite Lyon 1/INSA de Lyon, ECL, 36 avenue Guy de Collongue, 69134 Ecully Cedex (France); Wild, J. [Schneider Electric, 37 quai Merlin, 38050 Grenoble Cedex 9 (France)

    2008-09-15

    This article describes direct numerical simulation of the first three milliseconds following ignition of the arc in a low-voltage circuit-breaker using a computational-fluid-dynamics code adapted for electric-arc modelling. The mobile electrode is allowed for by a moving mesh. The results describe the evolution of the arc with time in terms of its detailed electrical, thermal and fluid dynamic properties. They allow the identification of several phases during the overall arc development process studied here: arc initialisation in the widening electrode gap, arc-thermal expansion, displacement of the arc towards the tip of the mobile electrode, and the beginning of commutation to the fixed electrode. (author)

  9. The Cu{sub 2}ZnSnS{sub 4} solar cell with high open circuit voltage

    Energy Technology Data Exchange (ETDEWEB)

    Yang, Min; Ma, Xun; Jiang, Zhi; Li, Zhishan; Liu, Sijia; Lu, Yilei; Wang, Shurong, E-mail: shrw88@aliyun.com

    2017-03-15

    In this paper, the effects of two different sulfurization processes on the CZTS films were investigated, and the results indicated that a rapid high-temperature crystallization process after sulfurization was beneficial for CZTS thin films to obtain a compact and flat surface with large grains. However, a common sulfurization without rapid high-temperature crystallization process would easily lead to undesirable properties of films, such as rough surface with pin holes, which degenerate the performance of devices. Cu{sub 2}ZnSnS{sub 4} (CZTS) solar cell based on a rapid high-temperature process after sulfurization achieved a high open circuit voltage of 722 mV and the best efficiency 3.32% was obtained.

  10. Numerical Analysis of the Arc Plasma in a Simplified Low-voltage Circuit Breaker Chamber with Ferromagnetic Materials

    Institute of Scientific and Technical Information of China (English)

    Wu Yi; Rong Mingzhe; Yang Qian; Hu Guangxia

    2005-01-01

    This paper is devoted to the simulation of the arc plasma in a simplified low-voltage circuit breaker chamber. Based on a group of coupled governing equations, a three-dimensional (3-D) arc plasma model is built and solved by a modified commercial code. Firstly, this paper presents a solution of the stationary state of the arc plasma and discusses the distribution of some parameters throughout the chamber. Secondly, with the ferromagnetic materials included,the balance of the stationary state is broken and a transient course is calculated. In light of the simulation results, the temperature distribution sequence, the arc motion and the plasma jet are then described and analyzed in detail.

  11. Characteristics of Overvoltage Protection with Cascade Application of Surge Protective Devices in Low-Voltage AC Power Circuits

    Directory of Open Access Journals (Sweden)

    RADULOVIC, V.

    2015-08-01

    Full Text Available Surge Protective Devices (SPDs are widely used for protection of the equipment in low-voltage AC power circuits against wide variety of surges. Cascade application of SPDs starting at the service entrance of a building and downstream toward near sensitive equipment is intended to ensure optimal energy distribution among installed SPDs, as well as proper equipment protection against surges. Characteristics of overvoltage protection with two-stage application of SPDs have been analyzed in the paper through performed measurements, followed by simulations and numerical modeling using the ATP/EMTP and MATLAB Simulink. Parametric analysis of the protection's characteristics in wide range of influencing factors has been performed in order to define a set of applicable solutions for proper selection and performance of SPDs.

  12. A Novel Thiophene Derivative-based Conjugated Polymer for Polymer Solar Cells with High Open-circuit Voltage

    Institute of Scientific and Technical Information of China (English)

    谌烈; 沈星星; 陈义旺

    2012-01-01

    A novel D-A alternative conjugated polymer PBDTDMCT containing benzo[1,2-b:4,5-b']dithiophene (BDT) and dimethyl thiophene-3,4-dicarboxylate (DMCT), was designed and synthesized by Stille cross-coupling reaction. The copolymer exhibited excellent solubility and good thermal stability. The optical band gap determined from the onset of absorption of the polymer film was 2.10 eV. By incorporation of the ester groups into the polymer side chain, the HOMO level of polymer PBDTDMT was tuned to be deep-lying (--5.65 eV). Open-circuit voltage of polymer solar cells constructed based on PBDTDMT and [6,6]-phenyl-CTwbutyric acid methyl ester (PCTIBM) can be tuned to achieve values as high as ca. 1.0 V.

  13. Simulation of current-voltage curves for inverted planar structure perovskite solar cells using equivalent circuit model with inductance

    Science.gov (United States)

    Cojocaru, Ludmila; Uchida, Satoshi; Jayaweera, Piyankarage V. V.; Kaneko, Shoji; Toyoshima, Yasutake; Nakazaki, Jotaro; Kubo, Takaya; Segawa, Hiroshi

    2017-02-01

    Physical modeling of hysteretic behavior in current-voltage (I-V) curves of perovskite solar cells (PSCs) is necessary for further improving their power conversion efficiencies (PCEs). The reduction of hysteresis in inverted planar structure PSCs (p-PSCs) has been achieved by using a [6,6]-phenyl-C61-butyric acid methyl ester (PCBM) layer. In the cases, the opposite trend of the I-V hysteresis has been observed where the forward scan shows slightly higher efficiency than the reverse scan. In this paper, an equivalent circuit model with inductance is proposed. This model consists of a Schottky diode involving a parasitic inductance focusing PCBM/Al(Ca) interface and accurately represents the opposite trend of the I-V hysteresis of the p-PSC with an inverted structure.

  14. General and Simple Decision Method for DG Penetration Level in View of Voltage Regulation at Distribution Substation Transformers

    Directory of Open Access Journals (Sweden)

    Joon-Ho Choi

    2013-09-01

    Full Text Available A distribution system was designed and operated by considering unidirectional power flow from a utility source to end-use loads. The large penetrations of distributed generation (DG into the existing distribution system causes a variety of technical problems, such as frequent tap changing problems of the on-load tap changer (OLTC transformer, local voltage rise, protection coordination, exceeding short-circuit capacity, and harmonic distortion. In view of voltage regulation, the intermittent fluctuation of the DG output power results in frequent tap changing operations of the OLTC transformer. Thus, many utilities limit the penetration level of DG and are eager to find the reasonable penetration limits of DG in the distribution system. To overcome this technical problem, utilities have developed a new voltage regulation method in the distribution system with a large DG penetration level. In this paper, the impact of DG on the OLTC operations controlled by the line drop compensation (LDC method is analyzed. In addition, a generalized determination methodology for the DG penetration limits in a distribution substation transformer is proposed. The proposed DG penetration limits could be adopted for a simplified interconnection process in DG interconnection guidelines.

  15. 一种间接测量电压互感器二次回路电压降的方法%A Method for Indirectly Measuring Voltage Transformer Secondary Circuit Voltage Drop

    Institute of Scientific and Technical Information of China (English)

    李固; 李纯坚; 傅子明; 刘芬; 梁旭常; 严杰峰

    2014-01-01

    通过研究电压互感器(voltage transformer,VT)二次回路电压降的主要来源,分析 VT二次回路阻抗的构成和运行特性,发现接触电阻是导致 VT二次回路电压降变化的主要原因。当计量电压二次回路阻抗为确定值时,VT二次负荷和 VT二次回路压降存在着对应的关系,可以通过测量二次负荷值来了解二次回路阻抗值,进而推算 VT二次回路压降值。基于此,推导出了用 VT二次负荷计算出 VT二次回路电压降的公式,并提出了通过分析对比 VT二次回路负荷变化大小及趋势,来对 VT二次回路压降开展技术监督的工作方法。%By means of studying main source of voltage drop of voltage transformer secondary circuit,this paper analyzes constitution and running characteristic of VT secondary circuit and discovers the main reason is contact resistance. When im-pedance of metering voltage secondary circuit was a determined value,there was corresponding relationship between VT sec-ondary load and voltage drop and it was able to learn impedance value of the secondary circuit by measuring secondary load value and calculate voltage drop value of VT secondary circuit. A calculation formula for voltage drop value of VT secondary circuit was deduced by VT secondary load and a working method for developing technical supervision on voltage drop of VT secondary circuit was proposed by analyzing and comparing changes and trends of VT secondary load.

  16. Microstructural and Electronic Origins of Open-Circuit Voltage Tuning in Organic Solar Cells Based on Ternary Blends

    KAUST Repository

    Mollinger, Sonya A.

    2015-09-22

    © 2015 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim. Organic ternary heterojunction photovoltaic blends are sometimes observed to undergo a gradual evolution in open-circuit voltage (Voc) with increasing amounts of a second donor or an acceptor. The Voc is strongly correlated with the energy of the charge transfer state in the blend, but this value depends on both local and mesoscopic orders. In this work, the behavior of Voc in the presence of a wide range of interfacial electronic states is investigated. The key charge transfer state interfaces responsible for Voc in several model systems with varying morphology are identified. Systems consisting of one donor with two fullerene molecules and of one acceptor with a donor polymer of varying regio-regularity are used. The effects from the changing energetic disorder in the material and from the variation due to a law of simple mixtures are quantified. It has been found that populating the higher-energy charge transfer states is not responsible for the observed change in Voc upon the addition of a third component. Aggregating polymers and miscible fullerenes are compared, and it has been concluded that in both cases charge delocalization, aggregation, and local polarization effects shift the lowest-energy charge transfer state distribution. The open-circuit voltage evolution and charge transfer state interfaces in ternary organic photovoltaic blends are investigated using several model systems. The changes in subgap spectra from energetic disorder and increased population of higher energy states are analyzed and the lowest charge transfer state distribution is observed to shift due to local aggregation and delocalization effects.

  17. PIP2 in pancreatic β-cells regulates voltage-gated calcium channels by a voltage-independent pathway.

    Science.gov (United States)

    de la Cruz, Lizbeth; Puente, Erika I; Reyes-Vaca, Arturo; Arenas, Isabel; Garduño, Julieta; Bravo-Martínez, Jorge; Garcia, David E

    2016-10-01

    Phosphatidylinositol-4,5-bisphosphate (PIP2) is a membrane phosphoinositide that regulates the activity of many ion channels. Influx of calcium primarily through voltage-gated calcium (CaV) channels promotes insulin secretion in pancreatic β-cells. However, whether CaV channels are regulated by PIP2, as is the case for some non-insulin-secreting cells, is unknown. The purpose of this study was to investigate whether CaV channels are regulated by PIP2 depletion in pancreatic β-cells through activation of a muscarinic pathway induced by oxotremorine methiodide (Oxo-M). CaV channel currents were recorded by the patch-clamp technique. The CaV current amplitude was reduced by activation of the muscarinic receptor 1 (M1R) in the absence of kinetic changes. The Oxo-M-induced inhibition exhibited the hallmarks of voltage-independent regulation and did not involve PKC activation. A small fraction of the Oxo-M-induced CaV inhibition was diminished by a high concentration of Ca(2+) chelator, whereas ≥50% of this inhibition was prevented by diC8-PIP2 dialysis. Localization of PIP2 in the plasma membrane was examined by transfecting INS-1 cells with PH-PLCδ1, which revealed a close temporal association between PIP2 hydrolysis and CaV channel inhibition. Furthermore, the depletion of PIP2 by a voltage-sensitive phosphatase reduced CaV currents in a way similar to that observed following M1R activation. These results indicate that activation of the M1R pathway inhibits the CaV channel via PIP2 depletion by a Ca(2+)-dependent mechanism in pancreatic β- and INS-1 cells and thereby support the hypothesis that membrane phospholipids regulate ion channel activity by interacting with ion channels.

  18. Simulation of the Arc Behavior in Puffer-type High Voltage Circuit Breaker Considering the Influence of Nozzle Ablation

    Institute of Scientific and Technical Information of China (English)

    JIANG Xu; ZHONG Jianying; ZHANG Youpeng; ZHANG Gaochao; LI Xingwen; JIA Shenli

    2013-01-01

    In order to investigate the influence of nozzle ablation to arc,a 2 D axisymmetric magneto-hydro-dynamics arc model is developed to simulate the arc behavior during the whole interruption process in a puffer type high voltage circuit breaker,considering the nozzle ablating and the mixing process of Polytetrafluoroethylene(PTFE) vapor with SF6.The results show that the arc radius firstly increases and then decreases as arc current varies according to its sinusoida waveform.At 3.5 ms after arc initiation the nozzle ablation starts,and 2.5 ms later the current nearly reaches its peak value and nozzle ablation develops intensely.Meanwhile the nozzle is blocked by arc at this time and consequently the vapor concentration in nozzle reaches the highest.Then while the current decreasing and open distance increaseing the vapor concentration gradually decreases.Before current zero the extinction peak of arc voltage occurs.It indicates that the PTFE vapor enhances pressure rise in arc quenching chamber and strengthens the arc blocking effect on nozzle; the arc radius is wider and arc temperature is lower when nozzle ablation is considered.

  19. Technical-economic evaluation of the utilization of closing resistor in CEMIG extra-high voltage circuit breakers

    Energy Technology Data Exchange (ETDEWEB)

    Rocha, Angelica C.O.; Pinto, Roberto del Giudice R.; Teixeira, Jose Cleber; Fonseca, Rodrigo Assuncao; F. Junior, Sebastiao V. [Companhia Energetica de Minas Gerais (CEMIG), Belo Horizonte, MG (Brazil)

    1994-12-31

    This paper presents the technical and economic studies performed by CEMIG, Companhia Energetica de Minas Gerais, Brazil, concerning the use of closing resistor in its extra-high voltage (EHV) breakers. The analysis emphasizes the advantages which could be achieved with the elimination of the resistor as far as costs and reliability are concerned. This evaluation was motivated by two 500 kV breaker failures resulting from the breakdown of the closing resistor operation mechanism. These occurrences resulted in operative restriction for CEMIG EHV system. The analysis demanded a review of the capability criteria of silicon carbide (Si C) gap arresters, which are still greatly used in CEMIG EHV System, and of the procedures to be applied when carrying out the transient studies. The investigation resulted in the prompt removal of closing resistors from circuit breakers in CEMIG extra-high voltage system generating an economy of approximately U$ 840,00 and an improvement in safety and system reliability. (author) 13 refs., 4 figs., 1 tab.

  20. Recombination in polymer:Fullerene solar cells with open-circuit voltages approaching and exceeding 1.0 V

    KAUST Repository

    Hoke, Eric T.

    2012-09-14

    Polymer:fullerene solar cells are demonstrated with power conversion efficiencies over 7% with blends of PBDTTPD and PC 61 BM. These devices achieve open-circuit voltages ( V oc ) of 0.945 V and internal quantum efficiencies of 88%, making them an ideal candidate for the large bandgap junction in tandem solar cells. V oc \\'s above 1.0 V are obtained when the polymer is blended with multiadduct fullerenes; however, the photocurrent and fill factor are greatly reduced. In PBDTTPD blends with multiadduct fullerene ICBA, fullerene emission is observed in the photoluminescence and electroluminescence spectra, indicating that excitons are recombining on ICBA. Voltage-dependent, steady state and time-resolved photoluminescence measurements indicate that energy transfer occurs from PBDTTPD to ICBA and that back hole transfer from ICBA to PBDTTPD is inefficient. By analyzing the absorption and emission spectra from fullerene and charge transfer excitons, we estimate a driving free energy of -0.14 ± 0.06 eV is required for efficient hole transfer. These results suggest that the driving force for hole transfer may be too small for efficient current generation in polymer:fullerene solar cells with V oc values above 1.0 V and that non-fullerene acceptor materials with large optical gaps ( > 1.7 eV) may be required to achieve both near unity internal quantum efficiencies and values of V oc exceeding 1.0 V. © 2013 WILEY-VCH Verlag GmbH and Co.

  1. A Novel 800mV Reference Current Source Circuit for Low-Power Low-Voltage Mixed-Mode Systems

    Science.gov (United States)

    Kwon, Oh Jun; Kwack, Kae Dal

    In this paper, a novel 800mV beta-multiplier reference current source circuit is presented. In order to cope with the narrow input common-mode range of the Opamp in the reference circuit, the resistive voltage divider was employed. High gain Opamp was designed to compensate for the intrinsic low output resistance of the MOS transistors. The proposed reference circuit was designed in a standard 0.18µm CMOS process with nominal Vth of 420mV and -450mV for n-MOS and p-MOS transistor, respectively. The total power consumption including Opamp is less than 50µW.

  2. Calcium binding protein-mediated regulation of voltage-gated calcium channels linked to human diseases

    Institute of Scientific and Technical Information of China (English)

    Nasrin NFJATBAKHSH; Zhong-ping FENG

    2011-01-01

    Calcium ion entry through voltage-gated calcium channels is essential for cellular signalling in a wide variety of cells and multiple physiological processes. Perturbations of voltage-gated calcium channel function can lead to pathophysiological consequences. Calcium binding proteins serve as calcium sensors and regulate the calcium channel properties via feedback mechanisms. This review highlights the current evidences of calcium binding protein-mediated channel regulation in human diseases.

  3. Low Voltage Power Supply Incorporating Ceramic Transformer

    CERN Document Server

    Imori, M

    2007-01-01

    A low voltage power supply provides the regulated output voltage of 1 V from the supply voltage around 48 V. The low voltage power supply incorporates a ceramic transformer which utilizes piezoelectric effect to convert voltage. The ceramic transformer isolates the secondary from the primary, thus providing the ground isolation between the supply and the output voltages. The ceramic transformer takes the place of the conventional magnetic transformer. The ceramic transformer is constructed from a ceramic bar and does not include any magnetic material. So the low voltage power supply can operate under a magnetic field. The output voltage is stabilized by feedback. A feedback loop consists of an error amplifier, a voltage controlled oscillator and a driver circuit. The amplitude ratio of the transformer has dependence on the frequency, which is utilized to stabilize the output voltage. The low voltage power supply is investigated on the analogy of the high voltage power supply similarly incorporating the cerami...

  4. New Breakdown Electric Field Calculation for SF6 High Voltage Circuit Breaker Applications

    Institute of Scientific and Technical Information of China (English)

    Ph.ROBIN-JOUAN; M.YOUSFI

    2007-01-01

    The critical electric fields of hot SF6 are calculated including both electron and ion kinetics in wide ranges of temperature and pressure,namely from 300 K up to 4000 K and 2 atmospheres up to 32 atmospheres respectively.Based on solving a multi-term electron Boltzmann equation the calculations use improved electron-gas collision cross sections for twelve SF6 dissociation products with a particular emphasis on the electron-vibrating molecule interactions.The ion kinetics is also considered and its role on the critical field becomes non negligible as the temperature is above 2000 K.These critical fields are then used in hydrodynamics simulations which correctly predict the circuit breaker behaviours observed in the case of breaking tests.

  5. A new ROIC with high-voltage protection circuit of HgCdTe e-APD FPA for passive and active imaging

    Science.gov (United States)

    Chen, Guoqiang; Zhang, Junling; Wang, Pan; Zhou, Jie; Gao, Lei; Ding, Ruijun

    2012-12-01

    HgCdTe electrons initiated avalanche photodiodes (e-APDs) in linear multiplication mode can be used for high speed applications such as active imaging. A readout integrated circuit of e-APD FPA is designed for dual mode passive/active imaging system. Unit cell circuit architecture of ROIC includes a high voltage protection module, a Sample-Hold circuit module, a comparator, output driver stage and a integrator module which includes a amplifier and three capacitors. Generally, APD FPA works at reversed bias such as 5V-15V in active imaging mode, and pixels' dark currents increase exponentially as the reverse-bias voltage is increased. Some cells of ROIC may be short to high voltage because of avalanche breakdown of diodes. If there is no protection circuit, the whole ROIC would be burnt out. Thus a protection circuit module introduced in every ROIC cell circuit is necessary to make sure the rest units of ROIC can still work. Conventional 5V CMOS process is applied to implement the high voltage protection with the small area other than LDMOS in high voltage BCD process in the limited 100μm×100μm pitch area. In integrator module, three integration capacitors are included in the ROIC to provide switchable well capacity. One of them can be shared in two modes in order to save area. Constraints such as pixel area and power lead us design toward a simple one-stage cascade operational transconductance amplifier (OTA) as pre-amplifier which can avoid potential instability caused by inaccuracy of MOSFET Model at 77K.

  6. Incentive-Based Voltage Regulation in Distribution Networks

    Energy Technology Data Exchange (ETDEWEB)

    Dall-Anese, Emiliano [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Baker, Kyri A [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Zhou, Xinyang [University of Colorado; Chen, Lijun [University of Colorado

    2017-07-03

    This paper considers distribution networks fea- turing distributed energy resources, and designs incentive-based mechanisms that allow the network operator and end-customers to pursue given operational and economic objectives, while concurrently ensuring that voltages are within prescribed limits. Two different network-customer coordination mechanisms that require different amounts of information shared between the network operator and end-customers are developed to identify a solution of a well-defined social-welfare maximization prob- lem. Notably, the signals broadcast by the network operator assume the connotation of prices/incentives that induce the end- customers to adjust the generated/consumed powers in order to avoid the violation of the voltage constraints. Stability of the proposed schemes is analytically established and numerically corroborated.

  7. Incentive-Based Voltage Regulation in Distribution Networks: Preprint

    Energy Technology Data Exchange (ETDEWEB)

    Zhou, Xinyang; Chen, Lijun; Dall' Anese, Emiliano; Baker, Kyri

    2017-03-03

    This paper considers distribution networks fea- turing distributed energy resources, and designs incentive-based mechanisms that allow the network operator and end-customers to pursue given operational and economic objectives, while concurrently ensuring that voltages are within prescribed limits. Two different network-customer coordination mechanisms that require different amounts of information shared between the network operator and end-customers are developed to identify a solution of a well-defined social-welfare maximization prob- lem. Notably, the signals broadcast by the network operator assume the connotation of prices/incentives that induce the end- customers to adjust the generated/consumed powers in order to avoid the violation of the voltage constraints. Stability of the proposed schemes is analytically established and numerically corroborated.

  8. Short-Term State Forecasting-Based Optimal Voltage Regulation in Distribution Systems: Preprint

    Energy Technology Data Exchange (ETDEWEB)

    Yang, Rui; Jiang, Huaiguang; Zhang, Yingchen

    2017-05-17

    A novel short-term state forecasting-based optimal power flow (OPF) approach for distribution system voltage regulation is proposed in this paper. An extreme learning machine (ELM) based state forecaster is developed to accurately predict system states (voltage magnitudes and angles) in the near future. Based on the forecast system states, a dynamically weighted three-phase AC OPF problem is formulated to minimize the voltage violations with higher penalization on buses which are forecast to have higher voltage violations in the near future. By solving the proposed OPF problem, the controllable resources in the system are optimally coordinated to alleviate the potential severe voltage violations and improve the overall voltage profile. The proposed approach has been tested in a 12-bus distribution system and simulation results are presented to demonstrate the performance of the proposed approach.

  9. Energy from CO2 using capacitive electrodes--theoretical outline and calculation of open circuit voltage.

    Science.gov (United States)

    Paz-Garcia, J M; Schaetzle, O; Biesheuvel, P M; Hamelers, H V M

    2014-03-15

    Recently, a new technology has been proposed for the utilization of energy from CO2 emissions (Hamelers et al., 2014). The principle consists of controlling the dilution process of CO2-concentrated gas (e.g., exhaust gas) into CO2-dilute gas (e.g., air) thereby extracting a fraction of the released mixing energy. In this paper, we describe the theoretical fundamentals of this technology when using a pair of charge-selective capacitive electrodes. We focus on the behavior of the chemical system consisting of CO2 gas dissolved in water or monoethanolamine solution. The maximum voltage given for the capacitive cell is theoretically calculated, based on the membrane potential. The different aspects that affect this theoretical maximum value are discussed.

  10. 一种微机电源的LDO设计与实现%Design and implementation of low dropout linear voltage regulator for the microcomputer power supply

    Institute of Scientific and Technical Information of China (English)

    胡玫; 王永喜; 刘保录

    2014-01-01

    针对微机电源稳压性能较差的缺点,设计一款输出电压为5 V,最大输出电流为1 A的低压差线性稳压器( LDO)。通过选择误差放大器、反馈电阻网络、大功率N沟道MOS管作为调整管;采用具有过温、限流保护功能的芯片和外围电路构成基准源电路,改善了稳压器的线性调整率。测试结果表明,室温下输入电压为5.5~25 V时,输出电压稳定在5 V,负载为5Ω时电压调整率为0.6%,显示出良好的稳压性能。%A low dropout linear regulator ( LDO) is designed with maximal output current of 1 A and 5 V output voltage for the microcomputer voltage regulation performance is poorer. The error amplifier, feedback resistance network, NMOS adjustment transistor are selected. Meanwhile the peripheral circuit and the chip which integrates the thermal and the current protect circuit make up the reference source to improve the performance of linear adjustment ratio. The test results show that when the input voltage of 5. 5 ~ 25 V at room temperature, the output voltage is 5 V. The voltage regulation rate was 0. 6% under 5 Ω load, which the voltage regulation performance is good.

  11. Operating principles of tristable circuits regulating cellular differentiation

    Science.gov (United States)

    Jia, Dongya; Jolly, Mohit Kumar; Harrison, William; Boareto, Marcelo; Ben-Jacob, Eshel; Levine, Herbert

    2017-06-01

    Many cell-fate decisions during embryonic development are governed by a motif comprised of two transcription factors (TFs) A and B that mutually inhibit each other and may self-activate. This motif, called as a self-activating toggle switch (SATS), can typically have three stable states (phenotypes)—two corresponding to differentiated cell fates, each of which has a much higher level of one TF than the other—≤ft(A,~B\\right)=≤ft(1,~0\\right) or ≤ft(0,~1\\right) —and the third state corresponding to an ‘undecided’ stem-like state with similar levels of both A and B—≤ft(A,~B\\right)=≤ft(1/2,1/2\\right) . Furthermore, two or more SATSes can be coupled together in various topologies in different contexts, thereby affecting the coordination between multiple cellular decisions. However, two questions remain largely unanswered: (a) what governs the co-existence and relative stability of these three stable states? (b) What orchestrates the decision-making of coupled SATSes? Here, we first demonstrate that the co-existence and relative stability of the three stable states in an individual SATS can be governed by the relative strength of self-activation, external signals activating and/or inhibiting A and B, and mutual degradation between A and B. Simultaneously, we investigate the effects of these factors on the decision-making of two coupled SATSes. Our results offer novel understanding into the operating principles of individual and coupled tristable self-activating toggle switches (SATSes) regulating cellular differentiation and can yield insights into synthesizing three-way genetic circuits and understanding of cellular reprogramming.

  12. Low-frequency switching voltage regulators for terrestrial photovoltaic systems

    Science.gov (United States)

    Delombard, R.

    1984-01-01

    The photovoltaic technology project and the stand alone applications project are discussed. Two types of low frequency switching type regulators were investigated. The design, operating characteristics and field application of these regulators is described. The regulators are small in size, low in cost, very low in power dissipation, reliable and allow considerable flexibility in system design.

  13. Improvement and test of high power amplifier high voltage interlock circuit%高功放高压联锁电路改进与测试

    Institute of Scientific and Technical Information of China (English)

    金华松; 邱冬冬; 刘斯亮

    2012-01-01

    Whether the device can work regularly was determined by the performance of high voltage interlock directly. Through the operating principle analysis of high voltage interlock circuit and AC time delayer of high power amplifier based on CPI mechanical cabinet, an improved high voltage interlock circuit solution and a test method applied in AC time delayer are studied. The improved interlock circuit overcomes the drawbacks of original high voltage interlock solution. The designed test circuit can carry out quantitative test of AC time delayer parameters.%高压联锁性能的好坏直接影响设备能否正常工作.通过分析CPI高功放(HPA)的延时加高压程序、高压联锁电路和交流延时器工作原理,研究出一种新改选的高压联锁电路方案和用于交流延时器的测试方法.分析阐述表明,该方案和测试方法克服了CPI高功放的高压联锁方案的弊端.另外,根据分析结果设计了延时测试电路,它可对交流延时器性能参数进行定量测试.

  14. Formation of a p-n heterojunction on GaP photocathodes for H-2 production providing an open-circuit voltage of 710 mV

    DEFF Research Database (Denmark)

    Malizia, Mauro; Seger, Brian; Chorkendorff, Ib

    2014-01-01

    Photocatalytic water splitting for the sustainable production of hydrogen using a two-photon tandem device requires careful optimization of the semiconductors used as photon absorbers. In this work we show how the open-circuit voltage of photocathodes for the hydrogen evolution reaction based on ...

  15. Low-voltage gallium-indium-zinc-oxide thin film transistors based logic circuits on thin plastic foil: Building blocks for radio frequency identification application

    NARCIS (Netherlands)

    Tripathi, A.K.; Smits, E.C.P.; Putten, J.B.P.H. van der; Neer, M. van; Myny, K.; Nag, M.; Steudel, S.; Vicca, P.; O'Neill, K.; Veenendaal, E. van; Genoe, G.; Heremans, P.; Gelinck, G.H.

    2011-01-01

    In this work a technology to fabricate low-voltage amorphous gallium-indium-zinc oxide thin film transistors (TFTs) based integrated circuits on 25 µm foils is presented. High performance TFTs were fabricated at low processing temperatures (<150 °C) with field effect mobility around 17 cm2 /V s. The

  16. Voltage regulation and reactive power supply capability of distributed generation : applications in active distribution systems

    Energy Technology Data Exchange (ETDEWEB)

    Katiraei, F.; Yazdani, A.; Uluski, R. [Quanta Technology, New York, NY (United States); Vaziri, M. [Pacific Gas and Electric Co., San Fransisco, CA (United States)

    2009-07-01

    Problems regarding voltage regulation on distribution feeders arise when there is a large demand for reactive power. The addition of distributed generation changes the power flow and voltage profile of a power system. The current practice is to use distributed generation passively and perform voltage regulation as before. However, this may not function well with high distributed generation penetration. This presentation discussed voltage regulation and the reactive power supply capability of distributed generation. Several applications in active distribution systems were presented. Specifically, the presentation discussed distributed interconnection challenges; utility practices and limiting factors; and the real and reactive power capabilities of distributed generation. A case study was also presented. It was concluded that in order for distributed generation to actively participate in real and reactive power management of distribution systems, a change is needed in standards and utility guidelines, along with a better understanding of distributed generation technologies and controls. 1 tab., 11 figs.

  17. 低压断路器的选型与应用%Selection and Application of Low-Voltage Circuit Breaker

    Institute of Scientific and Technical Information of China (English)

    钱金川; 贾文军

    2011-01-01

    介绍了低压断路器在配电线路、家用及类似场所负载、电动机负载的选型方法,并分析了在断路器保护功能以及不同负载特性情况下的选型策略。通过对低压断路器的合理选型,使低压断路器达到最佳的保护状态,并避免了因断路器选型不当及安装不合理而造成的安全隐患。%Introduction was made to a low-voltage circuit breaker type selection method in distribution line, household use, similar sites load and motor loads. Analysis was made to type selection strategy under circuit breaker protection function and different load characteristics conditions. Reasonable type selection of low-voltage circuit breakers enables low-voltage circuit breakers to reach optimal protection status, so as to avoid safety dangers caused by unsuitable circuit breaker type selection and unreasonable installation.

  18. Current Matching in Multifold DBP/C70 Organic Solar Cells With Open-Circuit Voltages of up to 6.44 V

    DEFF Research Database (Denmark)

    Ahmadpour, Mehrad; Liu, Yiming; Rubahn, Horst-Günter

    2017-01-01

    In this paper, we demonstrate a novel method for achieving high open-circuit voltages (Voc) in organic solar cells based on tetraphenyldibenzoperiflanthen (DBP) as donor and fullerene (C70) as acceptor molecules, by fabrication of multifold bilayer single cells stacked on top of each other....... As devices based on the material combination of DBP and C70 show relatively high open-circuit voltages of 0.87 V for single junction cells, and as both materials show broad absorption in the visible region pronounced peaks, they become ideal candidates as active layer materials in tandem stacked solar cells......, we demonstrate that the efficiency of these novel devices can be improved from 3.1% to 4.4% (best performing devices) in the case of a fivefold device structure, mainly due to the strong increase in the short-circuit current density, and thus lead to efficient small molecule-based solar cells high...

  19. Recombination dynamics as a key determinant of open circuit voltage in organic bulk heterojunction solar cells: a comparison of four different donor polymers

    Energy Technology Data Exchange (ETDEWEB)

    Maurano, Andrea; Hamilton, Rick; Shuttle, Chris G.; O' Regan, Brian; Zhang, Weimin; McCulloch, Iain; Durrant, James R. [Departments of Chemistry, Imperial College London, South Kensington SW7 2AZ (United Kingdom); Ballantyne, Amy M.; Nelson, Jenny [Departments of Physics, Imperial College London, South Kensington SW7 2AZ (United Kingdom); Azimi, Hamed [Konarka Austria, Altenbergerstrasse 69, A-4040 Linz (Austria); Christian Doppler Laboratory for Surface Optics, Johannes Kepler University, Linz (Austria); Morana, Mauro; Brabec, Christoph J. [Konarka Austria, Altenbergerstrasse 69, A-4040 Linz (Austria)

    2010-11-24

    Transient photovoltage and charge extraction analyses are employed to analyzes charge carrier densities and bimolecular recombination dynamics in organic polymer: fullerene solar cells under open circuit operating conditions, employing four different donor polymers. An equation is derived which allows us to calculate the device V{sub OC} from these kinetic measurements. This equation allows us to calculate voltage output of devices within {+-} 25 meV of directly measured values. This analysis thus allows us to relate device open circuit voltage directly to the kinetics of bimolecular recombination, and thereby the influence of nanomorphology upon device voltage output. (Copyright copyright 2010 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  20. CH3 NH3 PbBr3 -CH3 NH3 PbI3 Perovskite-Perovskite Tandem Solar Cells with Exceeding 2.2 V Open Circuit Voltage.

    Science.gov (United States)

    Heo, Jin Hyuck; Im, Sang Hyuk

    2016-07-01

    Perovskite-perovskite tandem solar cells with open-circuit voltages of over 2.2 V are reported. These cost-effective, solution-processible perovskite hybrid tandem solar cells with high open-circuit voltages are fabricated by the simple lamination of a front planar MAPbBr3 perovskite cell and a back MAPbI3 planar perovskite solar cell.

  1. High-voltage integrated active quenching circuit for single photon count rate up to 80 Mcounts/s.

    Science.gov (United States)

    Acconcia, Giulia; Rech, Ivan; Gulinatti, Angelo; Ghioni, Massimo

    2016-08-01

    Single photon avalanche diodes (SPADs) have been subject to a fast improvement in recent years. In particular, custom technologies specifically developed to fabricate SPAD devices give the designer the freedom to pursue the best detector performance required by applications. A significant breakthrough in this field is represented by the recent introduction of a red enhanced SPAD (RE-SPAD) technology, capable of attaining a good photon detection efficiency in the near infrared range (e.g. 40% at a wavelength of 800 nm) while maintaining a remarkable timing resolution of about 100ps full width at half maximum. Being planar, the RE-SPAD custom technology opened the way to the development of SPAD arrays particularly suited for demanding applications in the field of life sciences. However, to achieve such excellent performance custom SPAD detectors must be operated with an external active quenching circuit (AQC) designed on purpose. Next steps toward the development of compact and practical multichannel systems will require a new generation of monolithically integrated AQC arrays. In this paper we present a new, fully integrated AQC fabricated in a high-voltage 0.18 µm CMOS technology able to provide quenching pulses up to 50 Volts with fast leading and trailing edges. Although specifically designed for optimal operation of RE-SPAD devices, the new AQC is quite versatile: it can be used with any SPAD detector, regardless its fabrication technology, reaching remarkable count rates up to 80 Mcounts/s and generating a photon detection pulse with a timing jitter as low as 119 ps full width at half maximum. The compact design of our circuit has been specifically laid out to make this IC a suitable building block for monolithically integrated AQC arrays.

  2. Low drop-out voltage regulator as a candidate topology for photovoltaic solar facilities

    OpenAIRE

    Martínez García, Herminio

    2015-01-01

    This article aims to present the design of a 4.5-V, 450-mA low drop-out (LDO) voltage linear regulator based on a two-stage cascoded operational transconductance amplifier (OTA) as error amplifier for photovoltaic solar DC-DC regulation. The aforementioned two-stage OTA is designed with cascoded current mirroring technique to boost up the output impedance. The proposed OTA has a DC gain of 101 dB under no load condition. The designed reference voltage included in the LDO regulator is provi...

  3. Realizing Small Energy Loss of 0.55 eV, High Open-Circuit Voltage >1 V and High Efficiency >10% in Fullerene-Free Polymer Solar Cells via Energy Driver.

    Science.gov (United States)

    Cheng, Pei; Zhang, Mingyu; Lau, Tsz-Ki; Wu, Yao; Jia, Boyu; Wang, Jiayu; Yan, Cenqi; Qin, Meng; Lu, Xinhui; Zhan, Xiaowei

    2017-03-01

    A new, easy, and efficient approach is reported to enhance the driving force for charge transfer, break tradeoff between open-circuit voltage and short-circuit current, and simultaneously achieve very small energy loss (0.55 eV), very high open-circuit voltage (>1 V), and very high efficiency (>10%) in fullerene-free organic solar cells via an energy driver.

  4. Model parameter estimation approach based on incremental analysis for lithium-ion batteries without using open circuit voltage

    Science.gov (United States)

    Wu, Hongjie; Yuan, Shifei; Zhang, Xi; Yin, Chengliang; Ma, Xuerui

    2015-08-01

    To improve the suitability of lithium-ion battery model under varying scenarios, such as fluctuating temperature and SoC variation, dynamic model with parameters updated realtime should be developed. In this paper, an incremental analysis-based auto regressive exogenous (I-ARX) modeling method is proposed to eliminate the modeling error caused by the OCV effect and improve the accuracy of parameter estimation. Then, its numerical stability, modeling error, and parametric sensitivity are analyzed at different sampling rates (0.02, 0.1, 0.5 and 1 s). To identify the model parameters recursively, a bias-correction recursive least squares (CRLS) algorithm is applied. Finally, the pseudo random binary sequence (PRBS) and urban dynamic driving sequences (UDDSs) profiles are performed to verify the realtime performance and robustness of the newly proposed model and algorithm. Different sampling rates (1 Hz and 10 Hz) and multiple temperature points (5, 25, and 45 °C) are covered in our experiments. The experimental and simulation results indicate that the proposed I-ARX model can present high accuracy and suitability for parameter identification without using open circuit voltage.

  5. Open-circuit voltage deficit, radiative sub-bandgap states, and prospects in quantum dot solar cells.

    Science.gov (United States)

    Chuang, Chia-Hao Marcus; Maurano, Andrea; Brandt, Riley E; Hwang, Gyu Weon; Jean, Joel; Buonassisi, Tonio; Bulović, Vladimir; Bawendi, Moungi G

    2015-05-13

    Quantum dot photovoltaics (QDPV) offer the potential for low-cost solar cells. To develop strategies for continued improvement in QDPVs, a better understanding of the factors that limit their performance is essential. Here, we study carrier recombination processes that limit the power conversion efficiency of PbS QDPVs. We demonstrate the presence of radiative sub-bandgap states and sub-bandgap state filling in operating devices by using photoluminescence (PL) and electroluminescence (EL) spectroscopy. These sub-bandgap states are most likely the origin of the high open-circuit-voltage (VOC) deficit and relatively limited carrier collection that have thus far been observed in QDPVs. Combining these results with our perspectives on recent progress in QDPV, we conclude that eliminating sub-bandgap states in PbS QD films has the potential to show a greater gain than may be attainable by optimization of interfaces between QDs and other materials. We suggest possible future directions that could guide the design of high-performance QDPVs.

  6. Unraveling the High Open Circuit Voltage and High Performance of Integrated Perovskite/Organic Bulk-Heterojunction Solar Cells.

    Science.gov (United States)

    Dong, Shiqi; Liu, Yongsheng; Hong, Ziruo; Yao, Enping; Sun, Pengyu; Meng, Lei; Lin, Yuze; Huang, Jinsong; Li, Gang; Yang, Yang

    2017-08-09

    We have demonstrated high-performance integrated perovskite/bulk-heterojunction (BHJ) solar cells due to the low carrier recombination velocity, high open circuit voltage (VOC), and increased light absorption ability in near-infrared (NIR) region of integrated devices. In particular, we find that the VOC of the integrated devices is dominated by (or pinned to) the perovskite cells, not the organic photovoltaic cells. A Quasi-Fermi Level Pinning Model was proposed to understand the working mechanism and the origin of the VOC of the integrated perovskite/BHJ solar cell, which following that of the perovskite solar cell and is much higher than that of the low bandgap polymer based organic BHJ solar cell. Evidence for the model was enhanced by examining the charge carrier behavior and photovoltaic behavior of the integrated devices under illumination of monochromatic light-emitting diodes at different characteristic wavelength. This finding shall pave an interesting possibility for integrated photovoltaic devices to harvest low energy photons in NIR region and further improve the current density without sacrificing VOC, thus providing new opportunities and significant implications for future industry applications of this kind of integrated solar cells.

  7. Study of the Contributions of Donor and Acceptor Photoexcitations to Open Circuit Voltage in Bulk Heterojunction Organic Solar Cells

    Directory of Open Access Journals (Sweden)

    Douglas Yeboah

    2017-10-01

    Full Text Available One of the key parameters in determining the power conversion efficiency (PCE of bulk heterojunction (BHJ organic solar cells (OSCs is the open circuit voltage . The processes of exciting the donor and acceptor materials individually in a BHJ OSC are investigated and are found to produce two different expressions for . Using the contributions of electron and hole quasi-Fermi levels and charge carrier concentrations, the two different expressions are derived as functions of the energetics of the donor and acceptor materials and the photo-generated charge carrier concentrations, and calculated for a set of donor-acceptor blends. The simultaneous excitation of both the donor and acceptor materials is also considered and the corresponding , which is different from the above two, is derived. The calculated from the photoexcitation of the donor is found to be somewhat comparable with that obtained from the photoexcitation of the acceptor in most combinations of the donor and acceptor materials considered here. It is also found that the calculated from the simultaneous excitations of donor and acceptor in BHJ OSCs is also comparable with the other two . All three thus derived produce similar results and agree reasonably well with the measured values. All three depend linearly on the concentration of the photoexcited charge carriers and hence incident light intensity, which agrees with experimental results. The outcomes of this study are expected to help in finding materials that may produce higher and hence enhanced PCE in BHJ OSCs.

  8. An Optimal Control Strategy for DC Bus Voltage Regulation in Photovoltaic System with Battery Energy Storage

    Directory of Open Access Journals (Sweden)

    Muhamad Zalani Daud

    2014-01-01

    Full Text Available This paper presents an evaluation of an optimal DC bus voltage regulation strategy for grid-connected photovoltaic (PV system with battery energy storage (BES. The BES is connected to the PV system DC bus using a DC/DC buck-boost converter. The converter facilitates the BES power charge/discharge to compensate for the DC bus voltage deviation during severe disturbance conditions. In this way, the regulation of DC bus voltage of the PV/BES system can be enhanced as compared to the conventional regulation that is solely based on the voltage-sourced converter (VSC. For the grid side VSC (G-VSC, two control methods, namely, the voltage-mode and current-mode controls, are applied. For control parameter optimization, the simplex optimization technique is applied for the G-VSC voltage- and current-mode controls, including the BES DC/DC buck-boost converter controllers. A new set of optimized parameters are obtained for each of the power converters for comparison purposes. The PSCAD/EMTDC-based simulation case studies are presented to evaluate the performance of the proposed optimized control scheme in comparison to the conventional methods.

  9. An optimal control strategy for DC bus voltage regulation in photovoltaic system with battery energy storage.

    Science.gov (United States)

    Daud, Muhamad Zalani; Mohamed, Azah; Hannan, M A

    2014-01-01

    This paper presents an evaluation of an optimal DC bus voltage regulation strategy for grid-connected photovoltaic (PV) system with battery energy storage (BES). The BES is connected to the PV system DC bus using a DC/DC buck-boost converter. The converter facilitates the BES power charge/discharge to compensate for the DC bus voltage deviation during severe disturbance conditions. In this way, the regulation of DC bus voltage of the PV/BES system can be enhanced as compared to the conventional regulation that is solely based on the voltage-sourced converter (VSC). For the grid side VSC (G-VSC), two control methods, namely, the voltage-mode and current-mode controls, are applied. For control parameter optimization, the simplex optimization technique is applied for the G-VSC voltage- and current-mode controls, including the BES DC/DC buck-boost converter controllers. A new set of optimized parameters are obtained for each of the power converters for comparison purposes. The PSCAD/EMTDC-based simulation case studies are presented to evaluate the performance of the proposed optimized control scheme in comparison to the conventional methods.

  10. Silicon-on-insulator-based high-voltage, high-temperature integrated circuit gate driver for silicon carbide-based power field effect transistors

    Energy Technology Data Exchange (ETDEWEB)

    Tolbert, Leon M [ORNL; Huque, Mohammad A [ORNL; Blalock, Benjamin J [ORNL; Islam, Syed K [ORNL

    2010-01-01

    Silicon carbide (SiC)-based field effect transistors (FETs) are gaining popularity as switching elements in power electronic circuits designed for high-temperature environments like hybrid electric vehicle, aircraft, well logging, geothermal power generation etc. Like any other power switches, SiC-based power devices also need gate driver circuits to interface them with the logic units. The placement of the gate driver circuit next to the power switch is optimal for minimising system complexity. Successful operation of the gate driver circuit in a harsh environment, especially with minimal or no heat sink and without liquid cooling, can increase the power-to-volume ratio as well as the power-to-weight ratio for power conversion modules such as a DC-DC converter, inverter etc. A silicon-on-insulator (SOI)-based high-voltage, high-temperature integrated circuit (IC) gate driver for SiC power FETs has been designed and fabricated using a commercially available 0.8--m, 2-poly and 3-metal bipolar-complementary metal oxide semiconductor (CMOS)-double diffused metal oxide semiconductor (DMOS) process. The prototype circuit-s maximum gate drive supply can be 40-V with peak 2.3-A sourcing/sinking current driving capability. Owing to the wide driving range, this gate driver IC can be used to drive a wide variety of SiC FET switches (both normally OFF metal oxide semiconductor field effect transistor (MOSFET) and normally ON junction field effect transistor (JFET)). The switching frequency is 20-kHz and the duty cycle can be varied from 0 to 100-. The circuit has been successfully tested with SiC power MOSFETs and JFETs without any heat sink and cooling mechanism. During these tests, SiC switches were kept at room temperature and ambient temperature of the driver circuit was increased to 200-C. The circuit underwent numerous temperature cycles with negligible performance degradation.

  11. 大容量发电机出口断路器选择%Circuit Breakers Selection Method for Large-capacity AC High-voltage Generator

    Institute of Scientific and Technical Information of China (English)

    张爽

    2011-01-01

    针对大容量发电机出口断路器的选择问题,依据GB/T 14824-2008、IEEE Std C37.013-1997和IEC 60909-0-2001中的计算方法,并结合发电机出口断路器型式试验报告的有关数据,以某百万千瓦级发电机组为例进行了比较计算,分析计算结果,提出了对发电机出口短路器短路电流开断能力不能采用百分比而应采用绝对值进行校验.%For selecting large-capacity AC high-voltage generator circuit breakers in a large generator system, comparative calculations are conducted for a million kilowatts rated generator following the standards of GB/T 14824-2008, IEEE Std C37.013-1997 and IEC 60909-0-2001. The calculation results and the test reports of generator circuit breakers are analyzed, and a suggestion is hence offered that absolute value of short-circuit current should be used for examining the short-circuit current breaking capacity of an AC high-voltage generator circuit breaker instead of percentage value.

  12. Effect of Solar Array Capacitance on the Performance of Switching Shunt Voltage Regulator

    OpenAIRE

    Kumar, Anil R; Suresh, MS; Nagaraju, J

    2006-01-01

    Due to high power demand photovoltaic regulators are being switched at high frequency. The solar cell capacitance increases the ripple voltage of the switching regulators at higher switching frequencies. Increased ripple due to array capacitance is calculated and its effect in limiting the maximum design switching frequency is studied. An experimental switching regulator is designed and used to confirm the theoretical considerations. This study has identified a method of solar cell capacitanc...

  13. Dual Regulation of Voltage-Sensitive Ion Channels by PIP(2).

    Science.gov (United States)

    Rodríguez-Menchaca, Aldo A; Adney, Scott K; Zhou, Lei; Logothetis, Diomedes E

    2012-01-01

    Over the past 16 years, there has been an impressive number of ion channels shown to be sensitive to the major phosphoinositide in the plasma membrane, phosphatidylinositol 4,5-bisphosphate (PIP(2)). Among them are voltage-gated channels, which are crucial for both neuronal and cardiac excitability. Voltage-gated calcium (Cav) channels were shown to be regulated bidirectionally by PIP(2). On one hand, PIP(2) stabilized their activity by reducing current rundown but on the other hand it produced a voltage-dependent inhibition by shifting the activation curve to more positive voltages. For voltage-gated potassium (Kv) channels PIP(2) was first shown to prevent N-type inactivation regardless of whether the fast inactivation gate was part of the pore-forming α subunit or of an accessory β subunit. Careful examination of the effects of PIP(2) on the activation mechanism of Kv1.2 has shown a similar bidirectional regulation as in the Cav channels. The two effects could be distinguished kinetically, in terms of their sensitivities to PIP(2) and by distinct molecular determinants. The rightward shift of the Kv1.2 voltage dependence implicated basic residues in the S4-S5 linker and was consistent with stabilization of the inactive state of the voltage sensor. A third type of a voltage-gated ion channel modulated by PIP(2) is the hyperpolarization-activated cyclic nucleotide-gated (HCN) channel. PIP(2) has been shown to enhance the opening of HCN channels by shifting their voltage-dependent activation toward depolarized potentials. The sea urchin HCN channel, SpIH, showed again a PIP(2)-mediated bidirectional effect but in reverse order than the depolarization-activated Cav and Kv channels: a voltage-dependent potentiation, like the mammalian HCN channels, but also an inhibition of the cGMP-induced current activation. Just like the Kv1.2 channels, distinct molecular determinants underlied the PIP(2) dual effects on SpIH, with the proximal C-terminus implicated in the

  14. Dual Regulation of Voltage-Sensitive Ion Channels by PIP2

    Directory of Open Access Journals (Sweden)

    Aldo A Rodríguez Menchaca

    2012-09-01

    Full Text Available Over the past 16 years, there has been an impressive number of ion channels shown to be sensitive to the major phosphoinositide in the plasma membrane, phosphatidilinositol 4,5-bisphosphate (PIP2. Among them are voltage-gated channels, which are crucial for both neuronal and cardiac excitability. Voltage-gated calcium (Cav channels were shown to be regulated bidirectionally by PIP2. On one hand, PIP2 stabilized their activity by reducing current rundown but on the other hand it produced a voltage-dependent inhibition by shifting the activation curve to more positive voltages. For voltage-gated potassium (Kv channels PIP2 was first shown to prevent N-type inactivation. Careful examination of the effects of PIP2 on the activation mechanism of Kv1.2 has shown a similar bidirectional regulation as in the Cav channels. The two effects could be distinguished kinetically, in terms of their sensitivities to PIP2 and by distinct molecular determinants. The rightward shift of the Kv1.2 voltage dependence implicated basic residues in the S4-S5 linker and was consistent with stabilization of the inactive state of the voltage sensor. A third type of a voltage-gated ion channel modulated by PIP2 is the hyperpolarization-activated cyclic nucleotide-gated (HCN channel. PIP2 has been shown to enhance the opening of HCN channels by shifting their voltage-dependent activation toward depolarized potentials. The sea urchin HCN channel, SpIH, showed again a PIP2-mediated bidirectional effect but in reverse order than the depolarization-activated Cav and Kv channels: a voltage-dependent potentiation, like the mammalian HCN channels, but also an inhibition of the cGMP-induced current activation. Just like the Kv1.2 channels, distinct molecular determinants underlied the PIP2 dual effects on SpIH channels. The dual regulation of these very different ion channels, all of which are voltage dependent, points to conserved mechanisms of regulation of these channels by PIP2.

  15. Improvement of energy storage motor control circuit of hydraulic actuator in high-voltage circuit breakers%高压断路器液压操动机构储能电机控制回路改进

    Institute of Scientific and Technical Information of China (English)

    张全民; 赵玉柱

    2011-01-01

    高压断路器液压操动机构的常见故障是储能电机频繁启动。通过合理地设计储能电机的控制回路,减少了液压机构频繁启动的现象。%The fault of the mechanism of High voltage circuit-breaker is motor of storaging power high frequency starup.That rationally design control circuit of hydraulic mechanism reduce the fault that motor of storaging power high frequency starup.

  16. Impact of wind farms voltage regulation on the stability of the network frequency

    Energy Technology Data Exchange (ETDEWEB)

    Fernandez, R.D. [Laboratorio de Electronica Industrial, Control e Instrumentacion (LEICI), Facultad de Ingenieria, Universidad Nacional de La Plata, CC 91, 1900 La Plata (Argentina); Laboratorio de Electronica. Facultad de Ingenieria, Universidad Nacional de la Patagonia San Juan Bosco, Ciudad Universitaria, Km. 4, 9000 Comodoro Rivadavia (Argentina); Battaiotto, P.E.; Mantz, R.J. [Laboratorio de Electronica Industrial, Control e Instrumentacion (LEICI), Facultad de Ingenieria, Universidad Nacional de La Plata, CC 91, 1900 La Plata (Argentina)

    2008-07-15

    As it is well known, different kinds of wind farms can contribute to frequency and voltage regulation by means of active and reactive powers, respectively. This paper analyzes how the wind farm reactive power loop, which contribute to voltage regulation, modifies the location of the eigenvalues of a selected power system when the wind power penetration is increased. Previous to this analysis, aspects of the modeling of double fed induction generators in wind energy generation and power systems are discussed. Finally, simulations, which verify the theoretical results are presented. (author)

  17. Voltage regulation in LV grids by coordinated volt-var control strategies

    DEFF Research Database (Denmark)

    Juamperez Goñi, Miguel Angel; Yang, Guangya; Kjær, Søren Bækhøj

    2014-01-01

    in terms of network power losses and voltage level along the feeder. As a practical implementation, a reconfigurable hardware is used for developing a testing platform based on real-time measurements to regulate the reactive power level. The proposed testing platform has been developed within PVNET......The increasing penetration level of photovoltaic (PV) power generation in low voltage (LV) networks results in voltage rise issues, particularly at the end of the feeders. In order to mitigate this problem, several strategies, such as grid reinforcement, transformer tap change, demand......-side management, active power curtailment, and reactive power optimization methods, show their contribution to voltage support, yet still limited. This paper proposes a coordinated volt-var control architecture between the LV distribution transformer and solar inverters to optimize the PV power penetration level...

  18. Voltage regulation in MV networks with dispersed generations by a neural-based multiobjective methodology

    Energy Technology Data Exchange (ETDEWEB)

    Galdi, Vincenzo [Dipartimento di Ingegneria dell' Informazione e Ingegneria Elettrica, Universita degli studi di Salerno, Via Ponte Don Melillo 1, 84084 Fisciano (Italy); Vaccaro, Alfredo; Villacci, Domenico [Dipartimento di Ingegneria, Universita degli Studi del Sannio, Piazza Roma 21, 82100 Benevento (Italy)

    2008-05-15

    This paper puts forward the role of learning techniques in addressing the problem of an efficient and optimal centralized voltage control in distribution networks equipped with dispersed generation systems (DGSs). The proposed methodology employs a radial basis function network (RBFN) to identify the multidimensional nonlinear mapping between a vector of observable variables describing the network operating point and the optimal set points of the voltage regulating devices. The RBFN is trained by numerical data generated by solving the voltage regulation problem for a set of network operating points by a rigorous multiobjective solution methodology. The RBFN performance is continuously monitored by a supervisor process that notifies when there is the need of a more accurate solution of the voltage regulation problem if nonoptimal network operating conditions (ex post monitoring) or excessive distances between the actual network state and the neuron's centres (ex ante monitoring) are detected. A more rigorous problem solution, if required, can be obtained by solving the voltage regulation problem by a conventional multiobjective optimization technique. This new solution, in conjunction with the corresponding input vector, is then adopted as a new train data sample to adapt the RBFN. This online training process allows RBFN to (i) adaptively learn the more representative domain space regions of the input/output mapping without needing a prior knowledge of a complete and representative training set, and (ii) manage effectively any time varying phenomena affecting this mapping. The results obtained by simulating the regulation policy in the case of a medium-voltage network are very promising. (author)

  19. Lattice-matched Cu2ZnSnS4/CeO2 solar cell with open circuit voltage boost

    DEFF Research Database (Denmark)

    Crovetto, Andrea; Yan, Chang; Iandolo, Beniamino

    2016-01-01

    We report a reproducible enhancement of the open circuit voltage in Cu2ZnSnS4 solar cells by introduction of a very thin CeO2 interlayer between the Cu2ZnSnS4 absorber and the conventional CdS buffer. CeO2, a non-toxic earth-abundant compound, has a nearly optimal band alignment with Cu2ZnSnS4...... and the two materials are lattice-matched within 0.4%. This makes it possible to achieve an epitaxial interface when growing CeO2 by chemical bath deposition at temperatures as low as 50 °C. The open circuit voltage improvement is then attributed to a decrease in the interface recombination rate through...

  20. Lattice-matched Cu2ZnSnS4/CeO2 solar cell with open circuit voltage boost

    Science.gov (United States)

    Crovetto, Andrea; Yan, Chang; Iandolo, Beniamino; Zhou, Fangzhou; Stride, John; Schou, Jørgen; Hao, Xiaojing; Hansen, Ole

    2016-12-01

    We report a reproducible enhancement of the open circuit voltage in Cu2ZnSnS4 solar cells by introduction of a very thin CeO2 interlayer between the Cu2ZnSnS4 absorber and the conventional CdS buffer. CeO2, a non-toxic earth-abundant compound, has a nearly optimal band alignment with Cu2ZnSnS4 and the two materials are lattice-matched within 0.4%. This makes it possible to achieve an epitaxial interface when growing CeO2 by chemical bath deposition at temperatures as low as 50 °C. The open circuit voltage improvement is then attributed to a decrease in the interface recombination rate through formation of a high-quality heterointerface.

  1. Design of a Sample and Hold Circuit using Rail to Rail Low Voltage Compact Operational Amplifier and bootstrap Switching

    Directory of Open Access Journals (Sweden)

    Annu Saini

    2014-09-01

    Full Text Available This paper presents a low power high performance and higher sampling speed sample and hold circuit. The proposed circuit is designed at 180 nm technology and has high linearity. The circuit can be used for the ADC frontend applications and supports double sampling architecture. The proposed sample and hold circuit has common mode range beyond rail to rail and uses two differential pairs transistor stages connected in parallel as its input stage.

  2. LED Current Balance Using a Variable Voltage Regulator with Low Dropout vDS Control

    Directory of Open Access Journals (Sweden)

    Hung-I Hsieh

    2017-02-01

    Full Text Available A cost-effective light-emitting diode (LED current balance strategy using a variable voltage regulator (VVR with low dropout vDS control is proposed. This can regulate the multiple metal-oxide-semiconductor field-effect transistors (MOSFETs of the linear current regulators (LCR, maintaining low dropout vDS on the flat vGS-characteristic curves and making all drain currents almost the same. Simple group LCRs respectively loaded with a string LED are employed to implement the theme. The voltage VVdc from a VVR is synthesized by a string LED voltage NvD, source voltage vR, and a specified low dropout vDS = VQ. The VVdc updates instantly, through the control loop of the master LCR, which means that all slave MOSFETs have almost the same biases on their flat vGS-characteristic curves. This leads to all of the string LED currents being equal to each other, producing an almost even luminance. An experimental setup with microchip control is built to verify the estimations. Experimental results show that the luminance of all of the string LEDs are almost equal to one another, with a maximum deviation below 1% during a wide dimming range, while keeping all vDS of the MOSFETs at a low dropout voltage, as expected.

  3. Research on Mechanism of Overcurrent and Overvoltage When Contactless Tap Changer Switch Regulates Voltage on Load

    Institute of Scientific and Technical Information of China (English)

    2003-01-01

    Analyzes the mechanism of overvoltage when contactless tap changer switch which is applied in distributing transformer converted directly.When the device convert the tap-off,it employs the way that the SSR is switched on when voltage through zero and switched off when current through zero.But in the experiment we found that overvoltage will occur in the process of changing tap changer.The paper illustrates the mechanism of overvoltage in theory by analyzing the equivalent circuit and using analytic method of transition process.

  4. Mechanical Fault Diagnosis of High Voltage Circuit Breakers Based on Variational Mode Decomposition and Multi-Layer Classifier

    Directory of Open Access Journals (Sweden)

    Nantian Huang

    2016-11-01

    Full Text Available Mechanical fault diagnosis of high-voltage circuit breakers (HVCBs based on vibration signal analysis is one of the most significant issues in improving the reliability and reducing the outage cost for power systems. The limitation of training samples and types of machine faults in HVCBs causes the existing mechanical fault diagnostic methods to recognize new types of machine faults easily without training samples as either a normal condition or a wrong fault type. A new mechanical fault diagnosis method for HVCBs based on variational mode decomposition (VMD and multi-layer classifier (MLC is proposed to improve the accuracy of fault diagnosis. First, HVCB vibration signals during operation are measured using an acceleration sensor. Second, a VMD algorithm is used to decompose the vibration signals into several intrinsic mode functions (IMFs. The IMF matrix is divided into submatrices to compute the local singular values (LSV. The maximum singular values of each submatrix are selected as the feature vectors for fault diagnosis. Finally, a MLC composed of two one-class support vector machines (OCSVMs and a support vector machine (SVM is constructed to identify the fault type. Two layers of independent OCSVM are adopted to distinguish normal or fault conditions with known or unknown fault types, respectively. On this basis, SVM recognizes the specific fault type. Real diagnostic experiments are conducted with a real SF6 HVCB with normal and fault states. Three different faults (i.e., jam fault of the iron core, looseness of the base screw, and poor lubrication of the connecting lever are simulated in a field experiment on a real HVCB to test the feasibility of the proposed method. Results show that the classification accuracy of the new method is superior to other traditional methods.

  5. T-type voltage-gated calcium channels regulate the tone of mouse efferent arterioles

    DEFF Research Database (Denmark)

    Poulsen, Christian B; Al-Mashhadi, Rozh H; Cribbs, Leanne L;

    2011-01-01

    Voltage-gated calcium channels are important for the regulation of renal blood flow and the glomerular filtration rate. Excitation-contraction coupling in afferent arterioles is known to require activation of these channels and we studied their role in the regulation of cortical efferent arteriolar...... tone. We used microdissected perfused mouse efferent arterioles and found a transient vasoconstriction in response to depolarization with potassium; an effect abolished by removal of extracellular calcium. The T-type voltage-gated calcium channel antagonists mibefradil and nickel blocked this potassium....... Low concentrations of nickel, an agent that blocks Ca(v)3.2, had a similar effect. Thus, T-type voltage-gated calcium channels are functionally important for depolarization-induced vasoconstriction and subsequent dilatation in mouse cortical efferent arterioles.Kidney International advance online...

  6. An update on transcriptional and post-translational regulation of brain voltage-gated sodium channels.

    Science.gov (United States)

    Onwuli, Donatus O; Beltran-Alvarez, Pedro

    2016-03-01

    Voltage-gated sodium channels are essential proteins in brain physiology, as they generate the sodium currents that initiate neuronal action potentials. Voltage-gated sodium channels expression, localisation and function are regulated by a range of transcriptional and post-translational mechanisms. Here, we review our understanding of regulation of brain voltage-gated sodium channels, in particular SCN1A (NaV1.1), SCN2A (NaV1.2), SCN3A (NaV1.3) and SCN8A (NaV1.6), by transcription factors, by alternative splicing, and by post-translational modifications. Our focus is strongly centred on recent research lines, and newly generated knowledge.

  7. Correlation Between the Raman Crystallinity of p-Type Micro-Crystalline Silicon Layer and Open Circuit Voltage of n-i-p Solar Cells.

    Science.gov (United States)

    Jung, Junhee; Kim, Sunbo; Park, Jinjoo; Shin, Chonghoon; Pham, Duy Phong; Kim, Jiwoong; Chung, Sungyoun; Lee, Youngseok; Yi, Junsin

    2015-10-01

    This article mainly discusses the difference between p-i-n and n-i-p type solar cells. Their structural difference has an effect on cell performance, such as open circuit voltage and fill factor. Although the deposition conditions are the same for both p-i-n and n-i-p cases, the substrate layers for depositing p-type microcrystalline silicon layers differ. In n-i-p cells, the substrate layer is p-type amorphous silicon oxide layer; whereas, in p-i-n cells, the substrate layer is ZnO:Al. The interfacial change leads to a 12% difference in the crystallinity of the p-type microcrystalline silicon layers. When the p-type microcrystalline silicon layer's crystallinity was not sufficient to activate an internal electric field, the open circuit voltage and fill factor decreased 0.075 V and 7.36%, respectively. We analyzed this problem by comparing the Raman spectra, electrical conductivity, activation energy and solar cell performance. By adjusting the thickness of the p-type microcrystalline silicon layer, we increased the open circuit voltage of the n-i-p cell from 0.835 to 0.91 V.

  8. 空间辐射探测器滤波电路的设计%Design of Filter Circuit in High Voltage Unit of Particle Detector

    Institute of Scientific and Technical Information of China (English)

    施伟红; 于向前; 陈鸿飞; 邹鸿; 邹积清; 刘建文; 崔战国; 邵思霈

    2012-01-01

    To meet high stability, low ripple requirements of High Voltage Unit in Particle radiation detectors, to design a hybrid LC and RC filter circuit to reduce power supply ripple. Through the theoretical analysis, Pspice simulation and test,the results are verified. According to this design,a High Voltage Unit was made in a high -energy particle detector on a Satelite, output voltage ripple coefficient is small, met the design purposes. Test proved that this circuit design, simple, efficient, can provide a reference for this kind of circuit design.%为满足粒子辐射探测器高压电源高稳定、低纹波的要求,设计一种LC和RC混合滤波电路来降低电源纹波,并进行理论分析、PSpice仿真和试验对结果进行验证.按照这种设计实现的某型号卫星高能粒子探测器的高压电源,输出电压稳定、纹波系数小,达到设计目的.试验证明这种电路设计简单、高效,可为相关电路设计提供参考.

  9. Polypyrrole: FeOx·ZnO nanoparticle solar cells with breakthrough open-circuit voltage prepared from relatively stable liquid dispersions

    KAUST Repository

    Zong, Baoyu

    2014-01-01

    Organic hybrid solar cells with a large open-circuit voltage, up to above that of 1.5 V standard battery voltage, were demonstrated using blends of polypyrrole: Fe2O3·ZnO nanoparticles as active-layers. The cell active-layers were readily coated in open air from relatively stable liquid dark-color polypyrrole-based dispersions, which were synthesized using appropriate surfactants during the in situ polymerization of pyrrole with FeCl3 or both H2O2 and FeCl3 as the oxidizers. The performance of the cells depends largely on the synthesized blend phase, which is determined by the surfactants, oxidizers, as well as the reactant ratio. Only the solar cells fabricated from the stable dispersions can produce both a high open-circuit voltage (>1.0 V) and short-circuit current (up to 7.5 mA cm-2) due to the relatively uniform porous network nanomorphology and higher shunt to series resistance ratio of the active-layers. The cells also display a relatively high power-conversion efficiency of up to ∼3.8%. This journal is

  10. TIME DOMAIN REFLECTOMETRY FOR THE LOCALIZATION OF ELECTRICAL FAULTS IN THE INSTRUMENTATION OF THE LHC STRING MAGNETS A Study Case of Voltage Tap, Temperature, and Pressure Transducer Circuits

    CERN Document Server

    Komorowski, P

    1999-01-01

    Time Domain Reflectometry (TDR) is one of the most powerful methods used to analyze the integrity of the signal propagating in a transmission line. The method is based on the principle that the wave propagating in the line is reflected at the locations where the impedance of the line changes. The fault points, joints, branches, junctions, abrupt cross-section changes, etc., cause such reflections. The reflectometry technique involves the excitation of the circuit under test with either a fast edge step function or a well-defined impulse confined in time and frequency domains, and thereafter detection of the amplitude and time of the reflections. Both variants of the method were successfully applied to localize open circuit faults in the voltage tap connections, pressure transducers, and temperature sensing carbon gages circuits of the LHC String Dipole Magnet MB2 and Short Straight Section Quadrupole.

  11. A Low-Dropout Voltage Regulator with a Fractional-Order Control

    Directory of Open Access Journals (Sweden)

    L. Kadlcik

    2016-06-01

    Full Text Available This paper presents a 5 V / 50 mA low-dropout voltage regulator (LDO. The LDO uses a fractional-order control for its regulation loop to achieve a high DC gain (for a tight DC regulation while avoiding (for a good stability a high gain at high frequency. No compensation zeros are needed. The unity gain frequency of the regulation loop also changes adaptively with the output current to maintain it below the frequency of non-dominant poles. The LDO is stable with any external capacitance larger than 50 nF, and is expected to operate in a harsh automotive environment, with junction temperature ranging from -40°C to 170°C and with supply voltage from 7 V to 36 V. The operation of the LDO has been verified by realizing it in the 350 nm I3T50 ON Semiconductor technology.

  12. The enhanced low dose rate sensitivity of a linear voltage regulator with different biases

    Institute of Scientific and Technical Information of China (English)

    Wang Yiyuan; Lu Wu; Ren Diyuan; Guo Qi; Yu Xuefeng; Gao Bo

    2011-01-01

    A linear voltage regulator was irradiated by 60Co γ at high and low dose rates with two bias conditions to investigate the dose rate effect.The devices exhibit enhanced low dose rate sensitivity (ELDRS) under both biases.Comparing the enhancement factors between zero and working biases,it was found that the ELDRS is more severe under zero bias conditions.This confirms that the ELDRS is related to the low electric field in a bipolar structure.The reasons for the change in the line regulation and the maximum drive current were analyzed by combining the principle of linear voltage regulator with irradiation response of the transistors and error amplifier in the regulator.This may be helpful for designing radiation hardened devices.

  13. A Price-Based Approach for Voltage Regulation and Power Loss Minimization in Power Distribution Networks

    NARCIS (Netherlands)

    Jafarian, Matin; Scherpen, Jacquelien M.A.; Aiello, Marco

    2016-01-01

    We present a price-based approach to deal with the challenges of the electrical power distribution systems with renewable generations. In specific, we address the power loss minimization and voltage regulation taking into account the actual grid capacity. Analogously, the cost function is reformulat

  14. Astrocyte regulation of sleep circuits: experimental and modeling perspectives

    Directory of Open Access Journals (Sweden)

    Tommaso eFellin

    2012-08-01

    Full Text Available Integrated within neural circuits, astrocytes have recently been shown to modulate brain rhythms thought to mediate sleep function. Experimental evidence suggests that local impact of astrocytes on single synapses translates into global modulation of neuronal networks and behavior. We discuss these findings in the context of current conceptual models of sleep generation and function, each of which have historically focused on neural mechanisms. We highlight the implications and the challenges introduced by these results from a conceptual and computational perspective. We further provide modeling directions on how these data might extend our knowledge of astrocytic properties and sleep function. Given our evolving understanding of how local cellular activities during sleep lead to functional outcomes for the brain, further mechanistic and theoretical understanding of astrocytic contribution to these dynamics will undoubtedly be of great basic and translational benefit.

  15. Regulation of voltage gated calcium channels by GPCRs and post-translational modification.

    Science.gov (United States)

    Huang, Junting; Zamponi, Gerald W

    2016-10-18

    Calcium entry via voltage gated calcium channels mediates a wide range of physiological functions, whereas calcium channel dysregulation has been associated with numerous pathophysiological conditions. There are myriad cell signaling pathways that act on voltage gated calcium channels to fine tune their activities and to regulate their cell surface expression. These regulatory mechanisms include the activation of G protein-coupled receptors and downstream phosphorylation events, and their control over calcium channel trafficking through direct physical interactions. Calcium channels also undergo post-translational modifications that alter both function and density of the channels in the plasma membrane. Here we focus on select aspects of these regulatory mechanisms and highlight recent developments.

  16. Nanosecond pulsed electric fields (nsPEFs) low cost generator design using power MOSFET and Cockcroft-Walton multiplier circuit as high voltage DC source

    Science.gov (United States)

    Sulaeman, M. Y.; Widita, R.

    2014-09-01

    Purpose: Non-ionizing radiation therapy for cancer using pulsed electric field with high intensity field has become an interesting field new research topic. A new method using nanosecond pulsed electric fields (nsPEFs) offers a novel means to treat cancer. Not like the conventional electroporation, nsPEFs able to create nanopores in all membranes of the cell, including membrane in cell organelles, like mitochondria and nucleus. NsPEFs will promote cell death in several cell types, including cancer cell by apoptosis mechanism. NsPEFs will use pulse with intensity of electric field higher than conventional electroporation, between 20-100 kV/cm and with shorter duration of pulse than conventional electroporation. NsPEFs requires a generator to produce high voltage pulse and to achieve high intensity electric field with proper pulse width. However, manufacturing cost for creating generator that generates a high voltage with short duration for nsPEFs purposes is highly expensive. Hence, the aim of this research is to obtain the low cost generator design that is able to produce a high voltage pulse with nanosecond width and will be used for nsPEFs purposes. Method: Cockcroft-Walton multiplier circuit will boost the input of 220 volt AC into high voltage DC around 1500 volt and it will be combined by a series of power MOSFET as a fast switch to obtain a high voltage with nanosecond pulse width. The motivation using Cockcroft-Walton multiplier is to acquire a low-cost high voltage DC generator; it will use capacitors and diodes arranged like a step. Power MOSFET connected in series is used as voltage divider to share the high voltage in order not to damage them. Results: This design is expected to acquire a low-cost generator that can achieve the high voltage pulse in amount of -1.5 kV with falltime 3 ns and risetime 15 ns into a 50Ω load that will be used for nsPEFs purposes. Further detailed on the circuit design will be explained at presentation.

  17. Nanosecond pulsed electric fields (nsPEFs) low cost generator design using power MOSFET and Cockcroft-Walton multiplier circuit as high voltage DC source

    Energy Technology Data Exchange (ETDEWEB)

    Sulaeman, M. Y.; Widita, R. [Department of Physics, Nuclear Physics and Biophysics Research Division, Faculty of Mathematics and Natural Science, Institut Teknologi Bandung, Bandung (Indonesia)

    2014-09-30

    Purpose: Non-ionizing radiation therapy for cancer using pulsed electric field with high intensity field has become an interesting field new research topic. A new method using nanosecond pulsed electric fields (nsPEFs) offers a novel means to treat cancer. Not like the conventional electroporation, nsPEFs able to create nanopores in all membranes of the cell, including membrane in cell organelles, like mitochondria and nucleus. NsPEFs will promote cell death in several cell types, including cancer cell by apoptosis mechanism. NsPEFs will use pulse with intensity of electric field higher than conventional electroporation, between 20–100 kV/cm and with shorter duration of pulse than conventional electroporation. NsPEFs requires a generator to produce high voltage pulse and to achieve high intensity electric field with proper pulse width. However, manufacturing cost for creating generator that generates a high voltage with short duration for nsPEFs purposes is highly expensive. Hence, the aim of this research is to obtain the low cost generator design that is able to produce a high voltage pulse with nanosecond width and will be used for nsPEFs purposes. Method: Cockcroft-Walton multiplier circuit will boost the input of 220 volt AC into high voltage DC around 1500 volt and it will be combined by a series of power MOSFET as a fast switch to obtain a high voltage with nanosecond pulse width. The motivation using Cockcroft-Walton multiplier is to acquire a low-cost high voltage DC generator; it will use capacitors and diodes arranged like a step. Power MOSFET connected in series is used as voltage divider to share the high voltage in order not to damage them. Results: This design is expected to acquire a low-cost generator that can achieve the high voltage pulse in amount of −1.5 kV with falltime 3 ns and risetime 15 ns into a 50Ω load that will be used for nsPEFs purposes. Further detailed on the circuit design will be explained at presentation.

  18. Radial MV networks voltage regulation with distribution management system coordinated controller

    Energy Technology Data Exchange (ETDEWEB)

    Bignucolo, Fabio; Caldon, Roberto [University of Padua, Department of Electrical Engineering, Via Gradenigo, 6/A, 35131 Padova (Italy); Prandoni, Valter [CESI Ricerca, Milan (Italy)

    2008-04-15

    The connection of a great number of distributed generation (DG) plants may cause a critical voltage regulation problem in actual medium voltage (MV) radial distribution networks. After a synthetic survey of different strategies reported in literature to solve this problem, a proposal for an active management of the distribution system which makes use of an innovative controller that coordinates the on load tap changer (OLTC) action with the regulation of reactive exchanges between DG plants and feeders, is presented. In order to test the effectiveness of the proposed regulation, the distribution management system coordinated controller (DMSCC) is applied to a realistic radial structure distribution network and its behaviour simulated in managing the MV system during its worst foreseeable working conditions. (author)

  19. Endocytic regulation of voltage-dependent potassium channels in the heart.

    Science.gov (United States)

    Ishii, Kuniaki; Norota, Ikuo; Obara, Yutaro

    2012-01-01

    Understanding the regulation of cardiac ion channels is critical for the prevention of arrhythmia caused by abnormal excitability. Ion channels can be regulated by a change in function (qualitative) and a change in number (quantitative). Functional changes have been extensively investigated for many ion channels including cardiac voltage-dependent potassium channels. By contrast, the regulation of ion channel numbers has not been widely examined, particularly with respect to acute modulation of ion channels. This article briefly summarizes stimulus-induced endocytic regulation of major voltage-dependent potassium channels in the heart. The stimuli known to cause their endocytosis include receptor activation, drugs, and low extracellular [K(+)], following which the potassium channels undergo either clathrin-mediated or caveolin-mediated endocytosis. Receptor-mediated endocytic regulation has been demonstrated for Kv1.2, Kv1.5, KCNQ1 (Kv7.1), and Kv4.3, while drug-induced endocytosis has been demonstrated for Kv1.5 and hERG. Low [K(+)](o)-induced endocytosis might be unique for hERG channels, whose electrophysiological characteristics are known to be under strong influence of [K(+)](o). Although the precise mechanisms have not been elucidated, it is obvious that major cardiac voltage-dependent potassium channels are modulated by endocytosis, which leads to changes in cardiac excitability.

  20. A Survey of Non-conventional Techniques for Low-voltage Low-power Analog Circuit Design

    National Research Council Canada - National Science Library

    F. Khateb; S. Bay Abo Dabbous; S. Vlassis

    2013-01-01

    ...). Therefore, this paper presents the operation principle, the advantages and disadvantages of each of these techniques, enabling circuit designers to choose the proper design technique based on application...

  1. Design of Automatic Control System of Three-phase Voltage Regulating Based on Single-chip Microcomputer%基于单片机的三相调压自动控制系统的设计

    Institute of Scientific and Technical Information of China (English)

    邢月华; 付磊; 薛章华

    2012-01-01

    针对传统的交流调压器难以满足实时、精确调压和稳压的问题,设计了一种基于单片机的三相调压自动控制系统,详细介绍了系统的硬件电路和软件的实现.该系统以AT89C51单片机为控制核心,可实时监测电压信号的变化,实现在设定电压下的手动、自动调压功能.该系统还可以实现0.01 V以上电压采集精度、0~400 V之间升压、降压及稳压的自动控制功能.试验结果表明,该系统具有电路简单,工作可靠性强和自动化水平高等优点.%Far problems that traditional AC voltage regulator is difficult to meet with real-time, precision regulator and voltage stabilization, an automatic control system of three-phase voltage regulating based on single-chip microcomputer was designed, realization of hardware circuit and software of the system were introduced in details. The system takes AT89C51 single-chip microcomputer as control core, can real-timely monitor change of voltage signal and achieve manual, automatic voltage regulating function according to set voltage. It also can achieve 0. 01 V voltage collection precision, automatic control functions of 0-400 V boost, buck and stabilization of voltage. The experiment results showed that the system has advatages such as simple circuit, strong work reliability and high automation level.

  2. VLSI Hybrid DC-DC Regulator

    OpenAIRE

    Cosp Vilella, Jordi; Martínez García, Herminio

    2015-01-01

    Hybrid DC-DC regulators are structures that combine both a linear voltage regulator and a switching DC-DC converter. The main objective of this hybrid topology is to converge, in a single circuit topology, the best of both alternatives: a small voltage output ripple, which is a common characteristic of linear regulator circuits, and good energy efficiency, as in switching alternatives. While the linear regulator fixes the required output voltage to a fixed value with negligible steady-state r...

  3. Output voltage regulation of a k15 mode piezoelectric transformer by an external L/C component.

    Science.gov (United States)

    Hu, Junhui; Chan, Kuang Hwee; Ng, Boon Siang

    2009-06-01

    Smooth regulation of output voltage of piezoelectric transformers can significantly widen the application range of piezoelectric transformers. So far the driving frequency of piezoelectric transformers has been used to regulate the output voltage at a matching load. However, the regulation range of voltage gain achieved by the method is usually very narrow within the acceptable range of efficiency. In this work, we investigate the possibility to regulate the output voltage of a k15 mode piezoelectric transformer by an external L/C component. The effects of an L/C component in series or parallel with the input and output ports on the voltage gain are investigated theoretically and experimentally. It is found that the voltage gain can be smoothly regulated in a relatively wide range by a tunable inductor that is in series with the input port. At a matching load of 80 Omega, the voltage gain can be regulated between 0.31 and 0.94 with efficiency larger than 90% and between 0.34 and 1.18 with efficiency about 80%. It is also found that a tunable capacitor in parallel or series with the output port can be used to regulate the voltage gain with efficiency higher than 90%.

  4. Hypothalamic circuits regulating appetite and energy homeostasis: pathways to obesity

    Directory of Open Access Journals (Sweden)

    Katharina Timper

    2017-06-01

    Full Text Available The ‘obesity epidemic’ represents a major global socioeconomic burden that urgently calls for a better understanding of the underlying causes of increased weight gain and its associated metabolic comorbidities, such as type 2 diabetes mellitus and cardiovascular diseases. Improving our understanding of the cellular basis of obesity could set the stage for the development of new therapeutic strategies. The CNS plays a pivotal role in the regulation of energy and glucose homeostasis. Distinct neuronal cell populations, particularly within the arcuate nucleus of the hypothalamus, sense the nutrient status of the organism and integrate signals from peripheral hormones including pancreas-derived insulin and adipocyte-derived leptin to regulate calorie intake, glucose metabolism and energy expenditure. The arcuate neurons are tightly connected to other specialized neuronal subpopulations within the hypothalamus, but also to various extrahypothalamic brain regions, allowing a coordinated behavioral response. This At a Glance article gives an overview of the recent knowledge, mainly derived from rodent models, regarding the CNS-dependent regulation of energy and glucose homeostasis, and illustrates how dysregulation of the neuronal networks involved can lead to overnutrition and obesity. The potential impact of recent research findings in the field on therapeutic treatment strategies for human obesity is also discussed.

  5. Asymptotic and numerical prediction of current-voltage curves for an organic bilayer solar cell under varying illumination and comparison to the Shockley equivalent circuit

    KAUST Repository

    Foster, J. M.

    2013-01-01

    In this study, a drift-diffusion model is used to derive the current-voltage curves of an organic bilayer solar cell consisting of slabs of electron acceptor and electron donor materials sandwiched together between current collectors. A simplified version of the standard drift-diffusion equations is employed in which minority carrier densities are neglected. This is justified by the large disparities in electron affinity and ionisation potential between the two materials. The resulting equations are solved (via both asymptotic and numerical techniques) in conjunction with (i) Ohmic boundary conditions on the contacts and (ii) an internal boundary condition, imposed on the interface between the two materials, that accounts for charge pair generation (resulting from the dissociation of excitons) and charge pair recombination. Current-voltage curves are calculated from the solution to this model as a function of the strength of the solar charge generation. In the physically relevant power generating regime, it is shown that these current-voltage curves are well-approximated by a Shockley equivalent circuit model. Furthermore, since our drift-diffusion model is predictive, it can be used to directly calculate equivalent circuit parameters from the material parameters of the device. © 2013 AIP Publishing LLC.

  6. Regulation of Na(+) channel inactivation by the DIII and DIV voltage-sensing domains.

    Science.gov (United States)

    Hsu, Eric J; Zhu, Wandi; Schubert, Angela R; Voelker, Taylor; Varga, Zoltan; Silva, Jonathan R

    2017-03-06

    Functional eukaryotic voltage-gated Na(+) (NaV) channels comprise four domains (DI-DIV), each containing six membrane-spanning segments (S1-S6). Voltage sensing is accomplished by the first four membrane-spanning segments (S1-S4), which together form a voltage-sensing domain (VSD). A critical NaV channel gating process, inactivation, has previously been linked to activation of the VSDs in DIII and DIV. Here, we probe this interaction by using voltage-clamp fluorometry to observe VSD kinetics in the presence of mutations at locations that have been shown to impair NaV channel inactivation. These locations include the DIII-DIV linker, the DIII S4-S5 linker, and the DIV S4-S5 linker. Our results show that, within the 10-ms timeframe of fast inactivation, the DIV-VSD is the primary regulator of inactivation. However, after longer 100-ms pulses, the DIII-DIV linker slows DIII-VSD deactivation, and the rate of DIII deactivation correlates strongly with the rate of recovery from inactivation. Our results imply that, over the course of an action potential, DIV-VSDs regulate the onset of fast inactivation while DIII-VSDs determine its recovery.

  7. Transient Recovery Voltages at the Main 132kV Line Bay GIS Circuit Breaker in a Windfarm

    DEFF Research Database (Denmark)

    Arana Aristi, Iván; Okholm, J.; Holbøll, Joachim

    2011-01-01

    parameters in the network was evaluated during a fault in the onshore substation. The rate of rise of recovery voltage (RRRV) and the maximum crest voltage (Uc) of the TRV across the GIS CB were compared against the standard values based on the type test results from the GIS. The investigations were...

  8. Assumption or Fact? Line-to-Neutral Voltage Expression in an Unbalanced 3-Phase Circuit during Inverter Switching

    Science.gov (United States)

    Masrur, M. A.

    2009-01-01

    This paper discusses the situation in a 3-phase motor or any other 3-phase system operating under unbalanced operating conditions caused by an open fault in an inverter switch. A dc voltage source is assumed as the input to the inverter, and under faulty conditions of the inverter switch, the actual voltage applied between the line to neutral…

  9. Fully on-chip switched capacitor NMOS low dropout voltage regulator

    CERN Document Server

    Camacho, D; Camacho, Daniel; Moreira, Paulo

    2010-01-01

    This paper presents a 1.5 V 50 mA low dropout voltage (LDO) regulator using an NMOS transistor as the output pass element. Continuous time,operation of the LDO is achieved using a new switched floating capacitor scheme that raises the gate voltage of the pass element. The regulator has a 0.2 V dropout at a 50 mA load and is stable for a wide load current range with loading capacitances up to 50 pF. The output variation when a full load step is applied is 300 mV and the recovery time is below 0.3 mu s. it is designed in a 0.13 mu m CMOS process with an area of 0.008 mm(2) and its operation does not require any external component.

  10. Comparing and evaluating the voltage regulation of a UPFC and STATCOM

    Energy Technology Data Exchange (ETDEWEB)

    Al-Mawsawi, S.A. [University of Bahrain (Bahrain). College of Engineering

    2003-11-01

    In recent years it has been illustrated that the installation position of a Unified power flow controller (UPFC) has an important effect on its overall performance. A pulse width modulation (PWM) based UPFC used as a voltage regulator is modeled and analyzed to investigate its optimal position in the transmission line. This is compared with STATic COMpensator (STATCOM) device. This paper deals with the definition and simulation of the steady-state performance of the UPFC and STATCOM when they operate as a terminal voltage regulator. From the simulation results it is demonstrated that by varying the modulation index of the two devices it can control the distribution of active and reactive power flows. Furthermore, the comparisons for the optimum operation for the two devices have been performed. (author)

  11. Self-commutated high-voltage direct current transmission with DC circuit breakers. Backbone for the energy policy turnaround; Selbstgefuehrte Hochspannungs-Gleichstromuebertragung mit DC-Leistungsschalter. Rueckgrat fuer die Energiewende

    Energy Technology Data Exchange (ETDEWEB)

    Goerner, Raphael [ABB AG, Mannheim (Germany). Marketing und Vertrieb, Geschaeftsbereich Grid Systems

    2013-06-01

    The 'current war' between direct current and alternating current is extended by a new location. In the future, both technologies work together in order to provide a reliable power transmission in Germany and long-term in Europe. This is based on the self-guided high-voltage direct current transmission. In conjunction with direct current circuit breakers (DC circuit breaker) the power circuit breakers may help to make the transmission grids more flexible and to minimize losses.

  12. REACTIVE CURRENT OF AN INDUCTION ELECTRIC DRIVES WITH THYRISTOR VOLTAGE REGULATOR

    Directory of Open Access Journals (Sweden)

    J.V. Kovalova

    2014-12-01

    Full Text Available A model for a separation of reactive constituent from current of idling of an induction motor at its feed from a thyristor voltage regulator in the dependences on the control angle of thyristors is developed. As a result of modeling, dependence of relative reactive current which is approximated by formula for calculation of effective current of reactive constituent of nonsinusoidal current is obtained.

  13. High-efficiency voltage regulator and stabilizer for outdoor lighting installations

    OpenAIRE

    Blánquez, F.R.; Rebollo López, Emilio; Blázquez García, Francisco; Platero Gaona, Carlos Antonio; Frías Marín, Pablo

    2012-01-01

    This paper presents a high performance system of regulation and stabilization of luminous flux for public street lighting installations. Its purpose is to reduce the luminous flux of the luminaries efficiently by reducing their voltage supply, resulting in the improvement of energy efficiency in the installation. The system is basically composed of electromagnetic components which provide robustness and high-performance to the device, as well as minimum maintenance requirements. However, the ...

  14. 基于TTL数字电路控制的高压脉冲源%High-voltage pulse source controlled by TTL digital circuit

    Institute of Scientific and Technical Information of China (English)

    李玺钦; 丁明军; 吴红光; 冯莉; 刘云涛; 戴文峰; 黄雷

    2012-01-01

    给出了一种基于TTL数字电路作为高压脉冲源触发控制单元的设计原理和方法.介绍了高压脉冲源的工作原理,设计了一台脉冲输出幅度5 kV、脉冲宽度大于200 μs及脉冲前沿小于30 ns的高压脉冲源.将触发控制单元和前级开关金属氧化物半导体场效应管(MOSFET)组合成一体,控制后级气体高压开关管放电输出高压脉冲信号.实验结果验证了所采用的设计原理及方法的可行性,给出了单次触发情况下的实验结果.%The paper introduces a TTL digital circuit, which is designed as the trigger control system of high power pulse source, and presents the development of a high-voltage pulse source. In the source, the TTL circuit operated after the optical isolation circuit and power driver, and outputs pulse signals to drive MOSFET, which controls the pulse signal output from high-voltage switch. The source can outputs pulses with voltage of 5 kV, pulse-width larger than 200 Ωs and fall-time less than 30 ns. Besides long-distance control and local control mode, it also includes inner trigger and external trigger (one electric signal and one optical signal as the trigger). A series of experiments have been conducted to validate the design, and the one-shot trigger results are presented.

  15. Inverted Fuel Cell: Room-Temperature Hydrogen Separation from an Exhaust Gas by Using a Commercial Short-Circuited PEM Fuel Cell without Applying any Electrical Voltage.

    Science.gov (United States)

    Friebe, Sebastian; Geppert, Benjamin; Caro, Jürgen

    2015-06-26

    A short-circuited PEM fuel cell with a Nafion membrane has been evaluated in the room-temperature separation of hydrogen from exhaust gas streams. The separated hydrogen can be recovered or consumed in an in situ olefin hydrogenation when the fuel cell is operated as catalytic membrane reactor. Without applying an outer electrical voltage, there is a continuous hydrogen flux from the higher to the lower hydrogen partial pressure side through the Nafion membrane. On the feed side of the Nafion membrane, hydrogen is catalytically split into protons and electrons by the Pt/C electrocatalyst. The protons diffuse through the Nafion membrane, the electrons follow the short-circuit between the two brass current collectors. On the cathode side, protons and electrons recombine, and hydrogen is released. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  16. Voltage Regulation Using a Permanent Magnet Synchronous Generator with a Series Compensator: Preprint

    Energy Technology Data Exchange (ETDEWEB)

    Hsu, Ping; Wu, Ziping; Muljadi, Eduard; Gao, Wenzhong

    2015-08-24

    A wind power plant (WPP) is often operated at unity power factor, and the utility host where the WPP connects prefers to regulate the voltage. Although this may not be an issue in a stiff grid, the connection to a weak grid can be a problematic. This paper explores the advantages of having voltage regulation capability via reactive power control. Another issue in wind power generation is that not all turbines are able to control their reactive power due to technical reasons or contractual obligations. A synchronous condenser (SC) using a permanent magnet synchronous generator (PMSG) is proposed to provide necessary reactive power for regulating voltage at a weak grid connection. A PMSG has the advantage of higher efficiency and reliability. Because of its lack of a field winding, a PMSG is typically controlled by a full-power converter, which can be costly. In the proposed system, the reactive power of the SC is controlled by a serially connected compensator operating in a closed-loop configuration. The compensator also damps the PMSG’s tendency to oscillate. The compensator’s VA rating is only a fraction of the rating of the SC and the PMSG. In this initial investigation, the proposed scheme is shown to be effective by computer simulations.

  17. Voltage-dependent metabolic regulation of Kv2.1 channels in pancreatic beta-cells.

    Science.gov (United States)

    Yoshida, Masashi; Nakata, Masanori; Yamato, Shiho; Dezaki, Katsuya; Sugawara, Hitoshi; Ishikawa, San-e; Kawakami, Masanobu; Yada, Toshihiko; Kakei, Masafumi

    2010-05-28

    Voltage-gated potassium channels (Kv channels) play a crucial role in formation of action potentials in response to glucose stimulation in pancreatic beta-ells. We previously reported that the Kv channel is regulated by glucose metabolism, particularly by MgATP. We examined whether the regulation of Kv channels is voltage-dependent and mechanistically related with phosphorylation of the channels. In rat pancreatic beta-cells, suppression of glucose metabolism with low glucose concentrations of 2.8mM or less or by metabolic inhibitors decreased the Kv2.1-channel activity at positive membrane potentials, while increased it at potentials negative to -10 mV, suggesting that modulation of Kv channels by glucose metabolism is voltage-dependent. Similarly, in HEK293 cells expressing the recombinant Kv2.1 channels, 0mM but not 10mM MgATP modulated the channel activity in a manner similar to that in beta-cells. Both steady-state activation and inactivation kinetics of the channel were shifted toward the negative potential in association with the voltage-dependent modulation of the channels by cytosolic dialysis of alkaline phosphatase in beta-cells. The modulation of Kv-channel current-voltage relations were also observed during and after glucose-stimulated electrical excitation. These results suggest that the cellular metabolism including MgATP production and/or channel phosphorylation/dephosphorylation underlie the physiological modulation of Kv2.1 channels during glucose-induced insulin secretion.

  18. LTPS-TFT Pixel Circuit Compensating for TFT Threshold Voltage Shift and IR-Drop on the Power Line for AMOLED Displays

    Directory of Open Access Journals (Sweden)

    Ching-Lin Fan

    2012-01-01

    Full Text Available We propose a new pixel design for the active matrix organic light-emitting diode (AMOLED using low-temperature polycrystalline silicon thin-film transistors (LTPS-TFTs. The proposed pixel is composed of four switching TFTs, one driving TFT (DTFT, and one capacitor. The simulation results are performed by AIM-SPICE software. The error rate of OLED output current with (threshold voltage variation (0.3 V and power line drop by 1 V are improved to about 1.67% and 15%, respectively. Thus, the proposed pixel circuit can successfully overcome drawbacks suffered from DTFT threshold voltage deviation and IR-drop on power line.

  19. Towards a high open-circuit voltage by co-additives in electrolyte for high-efficiency dye-sensitized solar cells

    Science.gov (United States)

    Sun, Xun; Li, Yafeng; Mao, Haijuan; Dou, Jie; Wei, Mingdeng

    2017-08-01

    The co-additives of benzimidazole and 2-ethylimidazole in electrolyte have an obvious effect on the performance of dye-sensitized solar cells due to their good coordination ability of titanium dioxide, which could affect the energy levels and charge transfer process. Through a balance of the concentrations, the best efficiency of 7.93% with a high open-circuit voltage of 0.817 V is achieved for a cell fabricated with the electrolyte contains benzimidazole and 2-ehtylimidazole by a molar ratio of 9.5/0.5.

  20. A New Opamp-less CMOS Bandgap Voltage Reference Circuit%一种新型无运放CMOS带隙基准电路

    Institute of Scientific and Technical Information of China (English)

    冯树; 王永禄; 张跃龙

    2012-01-01

    Theory of bandgap reference voltage and conventional bandgap reference circuits were presented, and a novel bandgap reference circuit without op-amp was designed. In the circuit, MOS current mirrors and negative feedback clamping technique were used to avoid the use of operational amplifier, thus eliminating effects of offset and power supply rejection ratio (PSRR) of the operational amplifier on accuracy of bandgap voltage reference. Based on 0. 18 μm standard CMOS process, the circuit was simulated using Spectre of Cadence. Simulation results showed that the bandgap voltage reference circuit had a temperature coefficient of 6. 73 ×10-6/℃ in the temperature range from -40 °C to 125 ℃, and a PSRR of 54. 8 dB, and it consumed 0. 25 mW of power from 2. 5 V supply.%介绍了带隙基准原理和常规的带隙基准电路,设计了一种新型无运放带隙基准电路.该电路利用MOS电流镜和负反馈箝位技术,避免了运放的使用,从而消除了运放带隙基准电路中运放的失调电压和电源抑制比等对基准源精度的影响.该新型电路比传统无运放带隙基准电路具有更高的精度和电源抑制比.基于0.18μm标准CMOS工艺,在Cadence Spectre环境下仿真.采用2.5V电源电压,在-40℃~125℃温度范围的温度系数为6.73×10-6/℃,电源抑制比为54.8dB,功耗仅有0.25 mW.

  1. Distributed Control of Battery Energy Storage Systems for Voltage Regulation in Distribution Networks with High PV Penetration

    DEFF Research Database (Denmark)

    Zeraati, Mehdi; Golshan, Mohamad Esmaeil Hamedani; Guerrero, Josep M.

    2017-01-01

    issues of distribution networks. In this paper, the battery energy storage (BES) systems are used in order to solve the voltage rise during the peak PV generation as well as the voltage drop while meeting the peak load. A coordinated control strategy is proposed to regulate the charge/discharge of BESs...... using a combination of the local droop based control method and a distributed control scheme which ensures the voltages of feeder remain within allowed limits. Therefore, two different consensus algorithms are used: The first algorithm determines the BESs participation in voltage regulation in terms......The voltage rise problem in low voltage (LV) distribution networks with high penetration of photovoltaic (PV) resources is one of the most important challenges in the development of these renewable resources since it may prevent the maximum PV penetration considering the reliability and security...

  2. Molecular mechanism underlying β1 regulation in voltage- and calcium-activated potassium (BK) channels.

    Science.gov (United States)

    Castillo, Karen; Contreras, Gustavo F; Pupo, Amaury; Torres, Yolima P; Neely, Alan; González, Carlos; Latorre, Ramon

    2015-04-14

    Being activated by depolarizing voltages and increases in cytoplasmic Ca(2+), voltage- and calcium-activated potassium (BK) channels and their modulatory β-subunits are able to dampen or stop excitatory stimuli in a wide range of cellular types, including both neuronal and nonneuronal tissues. Minimal alterations in BK channel function may contribute to the pathophysiology of several diseases, including hypertension, asthma, cancer, epilepsy, and diabetes. Several gating processes, allosterically coupled to each other, control BK channel activity and are potential targets for regulation by auxiliary β-subunits that are expressed together with the α (BK)-subunit in almost every tissue type where they are found. By measuring gating currents in BK channels coexpressed with chimeras between β1 and β3 or β2 auxiliary subunits, we were able to identify that the cytoplasmic regions of β1 are responsible for the modulation of the voltage sensors. In addition, we narrowed down the structural determinants to the N terminus of β1, which contains two lysine residues (i.e., K3 and K4), which upon substitution virtually abolished the effects of β1 on charge movement. The mechanism by which K3 and K4 stabilize the voltage sensor is not electrostatic but specific, and the α (BK)-residues involved remain to be identified. This is the first report, to our knowledge, where the regulatory effects of the β1-subunit have been clearly assigned to a particular segment, with two pivotal amino acids being responsible for this modulation.

  3. Input- and Output-Specific Regulation of Serial Order Performance by Corticostriatal Circuits.

    Science.gov (United States)

    Rothwell, Patrick E; Hayton, Scott J; Sun, Gordon L; Fuccillo, Marc V; Lim, Byung Kook; Malenka, Robert C

    2015-10-21

    The serial ordering of individual movements into sequential patterns is thought to require synaptic plasticity within corticostriatal circuits that route information through the basal ganglia. We used genetically and anatomically targeted manipulations of specific circuit elements in mice to isolate the source and target of a corticostriatal synapse that regulates the performance of a serial order task. This excitatory synapse originates in secondary motor cortex, terminates on direct pathway medium spiny neurons in the dorsolateral striatum, and is strengthened by serial order learning. This experience-dependent and synapse-specific form of plasticity may sculpt the balance of activity in basal ganglia circuits during sequential movements, driving a disparity in striatal output that favors the direct pathway. This disparity is necessary for execution of responses in serial order, even though both direct and indirect pathways are active during movement initiation, suggesting dynamic modulation of corticostriatal circuitry contributes to the choreography of behavioral routines.

  4. Study of Voltage-sharing Circuit for Thyristor Series and Its Design%晶闸管串联均压电路设计与仿真研究

    Institute of Scientific and Technical Information of China (English)

    郭鹏; 王宏华; 冯进通; 尹祥顺; 李军民

    2015-01-01

    晶闸管串联式高压异步电动机软启动器应用前景广阔,晶闸管串联均压是其关键技术之一。对晶闸管串联均压电路进行了研究与设计,仿真分析了均压电路参数选取对均压效果的影响。仿真表明:采用动、静态均压电路可有效抑制开通和关断过程中晶闸管串联分压不均,对均压电路参数优化设计具有重要作用。%The high-voltage asynchronous motor soft starter is widely used in thyristor series. One of its key techniques is the volt-age-sharing of thyristor series. This paper researches on and designs the voltage-sharing circuit for thyristor series, and analyzes and simulates the relationship between voltage-sharing circuit parameters and voltage-sharing effect. The simulation results show that thyristor series voltage-sharing inequality in the process of conducting and turning off is effectively suppressed in the dynamic and static voltage-sharing circuit. The optimization of voltage-sharing circuit parameters plays an important role.

  5. CB1 cannabinoid receptor expression in the striatum: Association with corticostriatal circuits and developmental regulation

    Directory of Open Access Journals (Sweden)

    Vincent eVan Waes

    2012-03-01

    Full Text Available Corticostriatal circuits mediate various aspects of goal-directed behavior and are critically important for basal ganglia-related disorders. Activity in these circuits is regulated by the endocannabinoid system via stimulation of CB1 cannabinoid receptors. CB1 receptors are highly expressed in projection neurons and select interneurons of the striatum, but expression levels vary considerably between different striatal regions (functional domains. We investigated CB1 receptor expression within specific corticostriatal circuits by mapping CB1 mRNA levels in striatal sectors defined by their cortical inputs in rats. We also assessed changes in CB1 expression in the striatum during development. Our results show that CB1 expression is highest in juveniles (P25 and then progressively decreases towards adolescent (P40 and adult (P70 levels. At every age, CB1 receptors are predominantly expressed in sensorimotor striatal sectors, with considerably lower expression in associative and limbic sectors. Moreover, for most corticostriatal circuits there is an inverse relationship between cortical and striatal expression levels. Thus, striatal sectors with high CB1 expression (sensorimotor sectors tend to receive inputs from cortical areas with low expression, while striatal sectors with low expression (associative/limbic sectors receive inputs from cortical regions with higher expression (medial prefrontal cortex. In so far as CB1 mRNA levels reflect receptor function, our findings suggest differential CB1 signaling between different developmental stages and between sensorimotor and associative/limbic circuits. The regional distribution of CB1 receptor expression in the striatum further suggests that, in sensorimotor sectors, CB1 receptors mostly regulate GABA inputs from local axon collaterals of projection neurons, whereas in associative/limbic sectors, CB1 regulation of GABA inputs from interneurons and glutamate inputs may be more important.

  6. Bidirectional regulation of dendritic voltage-gated potassium channels by the fragile X mental retardation protein.

    Science.gov (United States)

    Lee, Hye Young; Ge, Woo-Ping; Huang, Wendy; He, Ye; Wang, Gordon X; Rowson-Baldwin, Ashley; Smith, Stephen J; Jan, Yuh Nung; Jan, Lily Yeh

    2011-11-17

    How transmitter receptors modulate neuronal signaling by regulating voltage-gated ion channel expression remains an open question. Here we report dendritic localization of mRNA of Kv4.2 voltage-gated potassium channel, which regulates synaptic plasticity, and its local translational regulation by fragile X mental retardation protein (FMRP) linked to fragile X syndrome (FXS), the most common heritable mental retardation. FMRP suppression of Kv4.2 is revealed by elevation of Kv4.2 in neurons from fmr1 knockout (KO) mice and in neurons expressing Kv4.2-3'UTR that binds FMRP. Moreover, treating hippocampal slices from fmr1 KO mice with Kv4 channel blocker restores long-term potentiation induced by moderate stimuli. Surprisingly, recovery of Kv4.2 after N-methyl-D-aspartate receptor (NMDAR)-induced degradation also requires FMRP, likely due to NMDAR-induced FMRP dephosphorylation, which turns off FMRP suppression of Kv4.2. Our study of FMRP regulation of Kv4.2 deepens our knowledge of NMDAR signaling and reveals a FMRP target of potential relevance to FXS.

  7. A current-excited triple-time-voltage oversampling method for bio-impedance model for cost-efficient circuit system.

    Science.gov (United States)

    Yan Hong; Yong Wang; Wang Ling Goh; Yuan Gao; Lei Yao

    2015-08-01

    This paper presents a mathematic method and a cost-efficient circuit to measure the value of each component of the bio-impedance model at electrode-electrolyte interface. The proposed current excited triple-time-voltage oversampling (TTVO) method deduces the component values by solving triple simultaneous electric equation (TSEE) at different time nodes during a current excitation, which are the voltage functions of time. The proposed triple simultaneous electric equations (TSEEs) allows random selections of the time nodes, hence numerous solutions can be obtained during a single current excitation. Following that, the oversampling approach is engaged by averaging all solutions of multiple TSEEs acquired after a single current excitation, which increases the practical measurement accuracy through the improvement of the signal-to-noise ratio (SNR). In addition, a print circuit board (PCB) that consists a switched current exciter and an analog-to-digital converter (ADC) is designed for signal acquisition. This presents a great cost reduction when compared against other instrument-based measurement data reported [1]. Through testing, the measured values of this work is proven to be in superb agreements on the true component values of the electrode-electrolyte interface model. This work is most suited and also useful for biological and biomedical applications, to perform tasks such as stimulations, recordings, impedance characterizations, etc.

  8. Molecular Basis of Regulating High Voltage-Activated Calcium Channels by S-Nitrosylation.

    Science.gov (United States)

    Zhou, Meng-Hua; Bavencoffe, Alexis; Pan, Hui-Lin

    2015-12-18

    Nitric oxide (NO) is involved in a variety of physiological processes, such as vasoregulation and neurotransmission, and has a complex role in the regulation of pain transduction and synaptic transmission. We have shown previously that NO inhibits high voltage-activated Ca(2+) channels in primary sensory neurons and excitatory synaptic transmission in the spinal dorsal horn. However, the molecular mechanism involved in this inhibitory action remains unclear. In this study, we investigated the role of S-nitrosylation in the NO regulation of high voltage-activated Ca(2+) channels. The NO donor S-nitroso-N-acetyl-DL-penicillamine (SNAP) rapidly reduced N-type currents when Cav2.2 was coexpressed with the Cavβ1 or Cavβ3 subunits in HEK293 cells. In contrast, SNAP only slightly inhibited P/Q-type and L-type currents reconstituted with various Cavβ subunits. SNAP caused a depolarizing shift in voltage-dependent N-type channel activation, but it had no effect on Cav2.2 protein levels on the membrane surface. The inhibitory effect of SNAP on N-type currents was blocked by the sulfhydryl-specific modifying reagent methanethiosulfonate ethylammonium. Furthermore, the consensus motifs of S-nitrosylation were much more abundant in Cav2.2 than in Cav1.2 and Cav2.1. Site-directed mutagenesis studies showed that Cys-805, Cys-930, and Cys-1045 in the II-III intracellular loop, Cys-1835 and Cys-2145 in the C terminus of Cav2.2, and Cys-346 in the Cavβ3 subunit were nitrosylation sites mediating NO sensitivity of N-type channels. Our findings demonstrate that the consensus motifs of S-nitrosylation in cytoplasmically accessible sites are critically involved in post-translational regulation of N-type Ca(2+) channels by NO. S-Nitrosylation mediates the feedback regulation of N-type channels by NO.

  9. Quasi-Linear Circuit

    Science.gov (United States)

    Bradley, William; Bird, Ross; Eldred, Dennis; Zook, Jon; Knowles, Gareth

    2013-01-01

    This work involved developing spacequalifiable switch mode DC/DC power supplies that improve performance with fewer components, and result in elimination of digital components and reduction in magnetics. This design is for missions where systems may be operating under extreme conditions, especially at elevated temperature levels from 200 to 300 degC. Prior art for radiation-tolerant DC/DC converters has been accomplished utilizing classical magnetic-based switch mode converter topologies; however, this requires specific shielding and component de-rating to meet the high-reliability specifications. It requires complex measurement and feedback components, and will not enable automatic re-optimization for larger changes in voltage supply or electrical loading condition. The innovation is a switch mode DC/DC power supply that eliminates the need for processors and most magnetics. It can provide a well-regulated voltage supply with a gain of 1:100 step-up to 8:1 step down, tolerating an up to 30% fluctuation of the voltage supply parameters. The circuit incorporates a ceramic core transformer in a manner that enables it to provide a well-regulated voltage output without use of any processor components or magnetic transformers. The circuit adjusts its internal parameters to re-optimize its performance for changes in supply voltage, environmental conditions, or electrical loading at the output

  10. THE STUDY OPPORTUNITIES OF SELF-OSCILLATIONS IN THE SYSTEM OF AUTOMATIC REGULATION OF THE VOLTAGE OF THE RINGS CONTROL WITH RELAY CONTROLLER BASED ON POWER KEY

    Directory of Open Access Journals (Sweden)

    D. S. Biluhin

    2009-03-01

    Full Text Available The possibility of application of the modern power semiconductor keys is considered for realization of asynchronous method of control of voltage level for circuits of on-board feeding of electric locomotives.

  11. Solenoid-Simulation Circuit

    Science.gov (United States)

    Simon, R. A.

    1986-01-01

    Electrical properties of solenoids imitated for tests of control circuits. Simulation circuit imitates voltage and current responses of two engine-controlling solenoids. Used in tests of programs of digital engine-control circuits, also provides electronic interface with circuits imitating electrical properties of pressure sensors and linear variable-differential transformers. Produces voltages, currents, delays, and discrete turnon and turnoff signals representing operation of solenoid in engine-control relay. Many such circuits used simulating overall engine circuitry.

  12. Development of a New Cascade Voltage-Doubler for Voltage Multiplication

    OpenAIRE

    Arash Toudeshki; Norman Mariun; Hashim Hizam; Noor Izzri Abdul Wahab

    2014-01-01

    For more than eight decades, cascade voltage-doubler circuits are used as a method to produce DC output voltage higher than the input voltage. In this paper, the topological developments of cascade voltage-doublers are reviewed. A new circuit configuration for cascade voltage-doubler is presented. This circuit can produce a higher value of the DC output voltage and better output quality compared to the conventional cascade voltage-doubler circuits, with the same number of stages.

  13. PIP2 regulation of KCNQ channels: biophysical and molecular mechanisms for lipid modulation of voltage-dependent gating

    Directory of Open Access Journals (Sweden)

    Mark Alan Zaydman

    2014-05-01

    Full Text Available Voltage-gated potassium (Kv channels contain voltage-sensing (VSD and pore-gate (PGD structural domains. During voltage-dependent gating, conformational changes in the two domains are coupled giving rise to voltage-dependent opening of the channel. In addition to membrane voltage, KCNQ (Kv7 channel opening requires the membrane lipid phosphatidylinositol 4,5-bisphosphate (PIP2. Recent studies suggest that PIP2 serves as a cofactor to mediate VSD-PGD coupling in KCNQ1 channels. In this review, we put these findings in the context of the current understanding of voltage-dependent gating, lipid modulation of Kv channel activation, and PIP2-regulation of KCNQ channels. We suggest that lipid-mediated coupling of functional domains is a common mechanism among KCNQ channels that may be applicable to other Kv channels and membrane proteins.

  14. PIP2 regulation of KCNQ channels: biophysical and molecular mechanisms for lipid modulation of voltage-dependent gating.

    Science.gov (United States)

    Zaydman, Mark A; Cui, Jianmin

    2014-01-01

    Voltage-gated potassium (Kv) channels contain voltage-sensing (VSD) and pore-gate (PGD) structural domains. During voltage-dependent gating, conformational changes in the two domains are coupled giving rise to voltage-dependent opening of the channel. In addition to membrane voltage, KCNQ (Kv7) channel opening requires the membrane lipid phosphatidylinositol 4,5-bisphosphate (PIP2). Recent studies suggest that PIP2 serves as a cofactor to mediate VSD-PGD coupling in KCNQ1 channels. In this review, we put these findings in the context of the current understanding of voltage-dependent gating, lipid modulation of Kv channel activation, and PIP2-regulation of KCNQ channels. We suggest that lipid-mediated coupling of functional domains is a common mechanism among KCNQ channels that may be applicable to other Kv channels and membrane proteins.

  15. The orbitofrontal-amygdala circuit and self-regulation of social-emotional behavior in autism.

    Science.gov (United States)

    Bachevalier, Jocelyne; Loveland, Katherine A

    2006-01-01

    Individuals with an autistic spectrum disorder are impaired not only in understanding others' mental states, but also in self-regulation of social-emotional behavior. Therefore, a model of the brain in autism must encompass not only those brain systems that subserve social-cognitive and emotional functioning, but also those that subserve the self-regulation of behavior in response to a changing social environment. We present evidence to support the hypothesis that developmental dysfunction of the orbitofrontal-amygdala circuit of the brain is a critical factor in the development of autism and that some of the characteristic deficits of persons with autism in socio-emotional cognition and behavioral self-regulation are related to early dysfunction of different components of this circuit. A secondary hypothesis posits that the degree of intellectual impairment present in individuals with autism is directly related to the integrity of the dorsolateral prefrontal-hippocampal circuit of the brain. Together, these hypotheses have the potential to help explain the neurodevelopmental basis of some of the primary manifestations of autism as well as the heterogeneity of outcomes.

  16. Down-regulation of endogenous KLHL1 decreases voltage-gated calcium current density.

    Science.gov (United States)

    Perissinotti, Paula P; Ethington, Elizabeth G; Cribbs, Leanne; Koob, Michael D; Martin, Jody; Piedras-Rentería, Erika S

    2014-05-01

    The actin-binding protein Kelch-like 1 (KLHL1) can modulate voltage-gated calcium channels in vitro. KLHL1 interacts with actin and with the pore-forming subunits of Cav2.1 and CaV3.2 calcium channels, resulting in up-regulation of P/Q and T-type current density. Here we tested whether endogenous KLHL1 modulates voltage gated calcium currents in cultured hippocampal neurons by down-regulating the expression of KLHL1 via adenoviral delivery of shRNA targeted against KLHL1 (shKLHL1). Control adenoviruses did not affect any of the neuronal properties measured, yet down-regulation of KLHL1 resulted in HVA current densities ~68% smaller and LVA current densities 44% smaller than uninfected controls, with a concomitant reduction in α(1A) and α(1H) protein levels. Biophysical analysis and western blot experiments suggest Ca(V)3.1 and 3.3 currents are also present in shKLHL1-infected neurons. Synapsin I levels, miniature postsynaptic current frequency, and excitatory and inhibitory synapse number were reduced in KLHL1 knockdown. This study corroborates the physiological role of KLHL1 as a calcium channel modulator and demonstrates a novel, presynaptic role.

  17. Determination of economically justified parameters of synchronous disconnection at low-voltage circuit switching via a synchronous vacuum contactor

    Directory of Open Access Journals (Sweden)

    A.V. Verkhola

    2014-04-01

    Full Text Available Dependence of a single switching procedure cost upon the contact opening delay time and delay-time spread is derived for a low-voltage synchronous vacuum contactor. For different cost levels, boundaries of permissible values of delay-time and delay-time spread are specified.

  18. Control of a Two-Stage Direct Power Converter with a Single Voltage Sensor Mounted in the Intermediary Circuit

    DEFF Research Database (Denmark)

    Klumpner, Christian; Wheeler, P.; Blaabjerg, Frede

    2004-01-01

    Controlling a converter requires not only a powerful processors but also accurate voltage and current sensors and fast and precise analogue-digital converters, which increase the cost per kW of the assembly, especially in the low power range. A matrix converter requires less transducers than a ba...

  19. 压控电压源二阶低通有源滤波电路设计与仿真%Design and simulation of two-order voltage source low pass active filter circuit controlled by voltage

    Institute of Scientific and Technical Information of China (English)

    侯卫周; 谷城

    2014-01-01

    利用M ultisim10.1软件对压控电压源二阶低通滤波器进行仿真分析,通过选择不同信号源观察输入、输出波形的相位关系和幅值关系,比较输出、输入波形幅值比是否等于通带电压放大倍数;调节负反馈电阻大小,观察品质因素变化对滤波器幅频特性和相频特性的影响,得到的仿真的结果与实际理论分析基本一致。仿真结果表明,将M ultisim10.1合理地引入到模拟电子线路实验教学中,能将一些高深、抽象的电子电路的理论教学变得具体和生动,有利于学生对电路的认知,提高电子线路理论课的教学效果和教学质量。%The two-order low pass active filter circuit of voltage controlled voltage source has been analyzed and simulated by Multisim10 .1 software ,observed the phase-frequency and amplitude-frequency of output and input waveform via choosing different signal sources ,the output and input waveform amplitude ratio compared is equal to the pass band voltage amplification or not ;when by adjusting negative feedback resistance ,the influence of phase-frequency and amplitude-frequency characteristics as quality factors changing can be observed .The simulation results are consistent with the practical theory .It shows that reasonably introducing Multisim10 .1 simulation technology could make some abstract and advanced theoretical teaching become concretely and lively ,thus it is suitable for cultivating students’ cognitive view of circuit ,further can improve teaching effect and teaching quality of the Electronic Circuit Theory couse .

  20. Design of the robust synchronous generator stator voltage regulator based on the interval plant model

    Directory of Open Access Journals (Sweden)

    Stojić Đorđe

    2013-01-01

    Full Text Available In this paper a novel method for the stator voltage regulator of a synchronous generator based on the interval plant mode, is presented. Namely, it is shown in the literature that, in order to design a controller for the first-order compensator, the limited number of interval plants needs to be examined. Consequently, the intervals of the plant model parameter variations used to calculate the four extreme interval plants required for the sequential PI controller design are determined. The controller is designed using frequency-domain-based techniques, while its robust performance is examined using simulation tests.

  1. Regulation of voltage-gated sodium channel expression in cancer: hormones, growth factors and auto-regulation.

    Science.gov (United States)

    Fraser, Scott P; Ozerlat-Gunduz, Iley; Brackenbury, William J; Fitzgerald, Elizabeth M; Campbell, Thomas M; Coombes, R Charles; Djamgoz, Mustafa B A

    2014-03-19

    Although ion channels are increasingly being discovered in cancer cells in vitro and in vivo, and shown to contribute to different aspects and stages of the cancer process, much less is known about the mechanisms controlling their expression. Here, we focus on voltage-gated Na(+) channels (VGSCs) which are upregulated in many types of carcinomas where their activity potentiates cell behaviours integral to the metastatic cascade. Regulation of VGSCs occurs at a hierarchy of levels from transcription to post-translation. Importantly, mainstream cancer mechanisms, especially hormones and growth factors, play a significant role in the regulation. On the whole, in major hormone-sensitive cancers, such as breast and prostate cancer, there is a negative association between genomic steroid hormone sensitivity and functional VGSC expression. Activity-dependent regulation by positive feedback has been demonstrated in strongly metastatic cells whereby the VGSC is self-sustaining, with its activity promoting further functional channel expression. Such auto-regulation is unlike normal cells in which activity-dependent regulation occurs mostly via negative feedback. Throughout, we highlight the possible clinical implications of functional VGSC expression and regulation in cancer.

  2. Functional reconstitution of the voltage-regulated sodium channel purified from electroplax of Electrophorus electricus

    Energy Technology Data Exchange (ETDEWEB)

    Rosenberg, R.L.

    1985-01-01

    The voltage-regulated NA channel is responsible for the depolarization of the excitable cell membrane during the normal action potential. This research has focused on the functional properties of the Na channel, purified from detergent extracts of electroplax membranes of the electric eel, and reconstituted into vesicles of defined phospholipid. These properties were assessed by measuring neurotoxin-modulated ion flux into the reconstituted membrane vesicles and by recording the single-channel currents of the purified channel by the patch-clamp method. The binding of tritiated tetrodotoxin (TTX) was employed as a marker for the purification of the channel. Two high-resolution fractionation steps, based on molecular charge and protein size, were used to obtain a preparation that is 80% homogeneous for a large peptide of 270,000 daltons. Radiotracer /sup 22/Na/sup +/ influx into the vesicles was stimulated by veratridine and by batrachotoxin (BTX) at concentrations of 100 ..mu..M and 5 ..mu..M, respectively. The stimulation by BTX was greater than that by veratridine, and can be as much as 16-fold over control influx levels. The stimulated influx is blocked by TTX with a K/sub i/ of 35 nM, and by local anesthetics in the normal pharmacological range. Large multilamellar vesicles prepared with a freeze-thaw step are suitable for single-channel recording techniques. When excised patches of the reconstituted membranes were voltage-clamped in the absence of activating neurotoxins, voltage-dependent single-channel currents were recorded. These displayed properties similar to those from native membranes of nerve and muscle. These results indicate that the protein purified on the basis of TTX binding is a functional Na channel possessing these functional domains: the ion-selective channel, the voltage sensors controlling activation and inactivation, and the sites of action of TTX, alkaloid neurotoxins, and local anesthetics.

  3. Single-Event Transient Testing of Low Dropout PNP Series Linear Voltage Regulators

    Science.gov (United States)

    Adell, Philippe; Allen, Gregory

    2013-01-01

    As demand for high-speed, on-board, digital-processing integrated circuits on spacecraft increases (field-programmable gate arrays and digital signal processors in particular), the need for the next generation point-of-load (POL) regulator becomes a prominent design issue. Shrinking process nodes have resulted in core rails dropping to values close to 1.0 V, drastically reducing margin to standard switching converters or regulators that power digital ICs. The goal of this task is to perform SET characterization of several commercial POL converters, and provide a discussion of the impact of these results to state-of-the-art digital processing IC through laser and heavy ion testing

  4. Protection of transformers and low voltage secondary circuits; Protecao de transformadores e circuitos secundarios em baixa tensao

    Energy Technology Data Exchange (ETDEWEB)

    Bueno, Alexandre Francisco Maia; Bouissou, Jean Jacques [Companhia Energetica de Minas Gerais (CEMIG), Belo Horizonte, MG (Brazil)

    1994-12-31

    This work discusses two themes related to equipment and circuit protection, both of which are components of overhead electric power transmission networks. Two CEMIG`s, the electric power company of Minas Gerais State - Southeast Brazil, experiences are presented. The work also discusses the technical reliability of these two protection conceptions. The results obtained results are also presented and discussed 3 refs., 3 figs., 2 tabs.

  5. Low-voltage polymer/small-molecule blend organic thin-film transistors and circuits fabricated via spray deposition

    Energy Technology Data Exchange (ETDEWEB)

    Hunter, By Simon; Anthopoulos, Thomas D., E-mail: t.anthopoulos@ic.ac.uk [Department of Physics and Centre for Plastic Electronics, Imperial College London, South Kensington SW7 2AZ (United Kingdom); Ward, Jeremy W.; Jurchescu, Oana D. [Department of Physics, Wake Forest University, Winston-Salem, North Carolina 27109 (United States); Payne, Marcia M.; Anthony, John E. [Department of Chemistry, University of Kentucky, Lexington, Kentucky 40506 (United States)

    2015-06-01

    Organic thin-film electronics have long been considered an enticing candidate in achieving high-throughput manufacturing of low-power ubiquitous electronics. However, to achieve this goal, more work is required to reduce operating voltages and develop suitable mass-manufacture techniques. Here, we demonstrate low-voltage spray-cast organic thin-film transistors based on a semiconductor blend of 2,8-difluoro- 5,11-bis (triethylsilylethynyl) anthradithiophene and poly(triarylamine). Both semiconductor and dielectric films are deposited via successive spray deposition in ambient conditions (air with 40%–60% relative humidity) without any special precautions. Despite the simplicity of the deposition method, p-channel transistors with hole mobilities of >1 cm{sup 2}/Vs are realized at −4 V operation, and unipolar inverters operating at −6 V are demonstrated.

  6. Operation of High-Voltage Transverse Shock Wave Ferromagnetic Generator in the Open Circuit and Charging Modes

    Science.gov (United States)

    2005-06-01

    FMGs are based on the transverse (when the shock wave propagates across the magnetization vector M) shock demagnetization of Nd2Fe14B hard...generators based on the transverse (when the shock wave propagates across the magnetization vector M) shock wave demagnetization of Nd2Fe14B hard...and photo of a high-voltage transverse FMG are shown in Fig. 1. It contains a hollow hard ferromagnetic cylindrical Nd2Fe14B energy-carrying

  7. Commutation circuit for an HVDC circuit breaker

    Science.gov (United States)

    Premerlani, William J.

    1981-01-01

    A commutation circuit for a high voltage DC circuit breaker incorporates a resistor capacitor combination and a charging circuit connected to the main breaker, such that a commutating capacitor is discharged in opposition to the load current to force the current in an arc after breaker opening to zero to facilitate arc interruption. In a particular embodiment, a normally open commutating circuit is connected across the contacts of a main DC circuit breaker to absorb the inductive system energy trapped by breaker opening and to limit recovery voltages to a level tolerable by the commutating circuit components.

  8. Design and engineering of intracellular-metabolite-sensing/regulation gene circuits in Saccharomyces cerevisiae.

    Science.gov (United States)

    Wang, Meng; Li, Sijin; Zhao, Huimin

    2016-01-01

    The development of high-throughput phenotyping tools is lagging far behind the rapid advances of genotype generation methods. To bridge this gap, we report a new strategy for design, construction, and fine-tuning of intracellular-metabolite-sensing/regulation gene circuits by repurposing bacterial transcription factors and eukaryotic promoters. As proof of concept, we systematically investigated the design and engineering of bacterial repressor-based xylose-sensing/regulation gene circuits in Saccharomyces cerevisiae. We demonstrated that numerous properties, such as induction ratio and dose-response curve, can be fine-tuned at three different nodes, including repressor expression level, operator position, and operator sequence. By applying these gene circuits, we developed a cell sorting based, rapid and robust high-throughput screening method for xylose transporter engineering and obtained a sugar transporter HXT14 mutant with 6.5-fold improvement in xylose transportation capacity. This strategy should be generally applicable and highly useful for evolutionary engineering of proteins, pathways, and genomes in S. cerevisiae.

  9. Micromolar-Affinity Benzodiazepine Receptors Regulate Voltage-Sensitive Calcium Channels in Nerve Terminal Preparations

    Science.gov (United States)

    Taft, William C.; Delorenzo, Robert J.

    1984-05-01

    Benzodiazepines in micromolar concentrations significantly inhibit depolarization-sensitive Ca2+ uptake in intact nerve-terminal preparations. Benzodiazepine inhibition of Ca2+ uptake is concentration dependent and stereospecific. Micromolar-affinity benzodiazepine receptors have been identified and characterized in brain membrane and shown to be distinct from nanomolar-affinity benzodiazepine receptors. Evidence is presented that micromolar, and not nanomolar, benzodiazepine binding sites mediate benzodiazepine inhibition of Ca2+ uptake. Irreversible binding to micromolar benzodiazepine binding sites also irreversibly blocked depolarization-dependent Ca2+ uptake in synaptosomes, indicating that these compounds may represent a useful marker for identifying the molecular components of Ca2+ channels in brain. Characterization of benzodiazepine inhibition of Ca2+ uptake demonstrates that these drugs function as Ca2+ channel antagonists, because benzodiazepines effectively blocked voltage-sensitive Ca2+ uptake inhibited by Mn2+, Co2+, verapamil, nitrendipine, and nimodipine. These results indicate that micromolar benzodiazepine binding sites regulate voltage-sensitive Ca2+ channels in brain membrane and suggest that some of the neuronal stabilizing effects of micromolar benzodiazepine receptors may be mediated by the regulation of Ca2+ conductance.

  10. A Capacitor-Free, Fast Transient Response Linear Voltage Regulator In a 180nm CMOS

    DEFF Research Database (Denmark)

    Deleuran, Alexander N.; Lindbjerg, Nicklas; Pedersen, Martin K.

    2015-01-01

    A 1.8 V capacitor-free linear regulator with fast transient response based on a new topology with a fast and slow regulation loop is presented. The design has been laid out and simulated in a 0.18 µm CMOS process. The design has a low component count and is tailored for system-on-chip integration....... A current step load from 0-50 mA with a rise time of 1 µs results in an undershoot in the output voltage of 140 mV for a period of 39 ns. The regulator sources up to 50 mA current load.......A 1.8 V capacitor-free linear regulator with fast transient response based on a new topology with a fast and slow regulation loop is presented. The design has been laid out and simulated in a 0.18 µm CMOS process. The design has a low component count and is tailored for system-on-chip integration...

  11. Simulation of the Process of Arc Energy-Effect in High Voltage Auto-Expansion SF6 Circuit Breaker

    Institute of Scientific and Technical Information of China (English)

    Rong Mingzhe; Yang Qian; Fan Chunduo

    2005-01-01

    A new magnetic hydro-dynamics (MHD) model of arc in H.V. auto-expansion SF6circuit breaker that takes into consideration nozzle ablation due to both radiation and thermal conduction is presented in this paper. The effect of PTFE (polytetrafluorethylene) vapor is considered in the mass, momentum and energy conservation equations of the constructed model. Then,the gas flow fields with and without conduction considered are simulated. By comparing the aforementioned two results, it is indicated that the arc's maximal temperature with conduction considered is 90 percent of that without considering conduction.

  12. High frequency capacitor-diode voltage multiplier dc-dc converter development

    Science.gov (United States)

    Kisch, J. J.; Martinelli, R. M.

    1977-01-01

    A power conditioner was developed which used a capacitor diode voltage multiplier to provide a high voltage without the use of a step-up transformer. The power conditioner delivered 1200 Vdc at 100 watts and was operated from a 120 Vdc line. The efficiency was in excess of 90 percent. The component weight was 197 grams. A modified boost-add circuit was used for the regulation. A short circuit protection circuit was used which turns off the drive circuit upon a fault condition, and recovers within 5 ms after removal of the short. High energy density polysulfone capacitors and high speed diodes were used in the multiplier circuit.

  13. Improve the open-circuit voltage of ZnO solar cells with inserting ZnS layers by two ways

    Energy Technology Data Exchange (ETDEWEB)

    Sun, Yunfei [State Key Laboratory of Luminescence and Applications, Changchun Institute of Optics, Fine Mechanics and Physics, Chinese Academy of Sciences, Changchun 130033 (China); Graduate School of the Chinese Academy of Sciences, Beijing 100049 (China); Yang, Jinghai, E-mail: jhyang1@jlnu.edu.cn [Institute of Condensed State Physics, Jilin Normal University, Siping 136000 (China); Yang, Lili; Cao, Jian [Institute of Condensed State Physics, Jilin Normal University, Siping 136000 (China); Gao, Ming [State Key Laboratory of Luminescence and Applications, Changchun Institute of Optics, Fine Mechanics and Physics, Chinese Academy of Sciences, Changchun 130033 (China); Graduate School of the Chinese Academy of Sciences, Beijing 100049 (China); Institute of Condensed State Physics, Jilin Normal University, Siping 136000 (China); Zhang, Zhiqiang; Wang, Zhe [Institute of Condensed State Physics, Jilin Normal University, Siping 136000 (China); Song, Hang [State Key Laboratory of Luminescence and Applications, Changchun Institute of Optics, Fine Mechanics and Physics, Chinese Academy of Sciences, Changchun 130033 (China)

    2013-04-15

    ZnS NPs layers were deposited on ZnO NRs by two different ways. One is spin coating; the other is successive ionic layer adsorption and reaction (SILAR) method. The ZnO NRs/ZnS NPs composites were verified by X-ray diffraction, X-ray photoelectron spectroscopy, and UV–visible spectrophotometer; their morphologies and thicknesses were examined by scanning electron microscopic and transmission electron microscopic images. The CdS quantum dot sensitized solar cells (QDSSCs) were constructed using ZnO NRs/ZnS NPs composites as photoanode and their photovoltaic characteristic was studied by J–V curves. The results indicated that the way of SILAR is more beneficial for retarding the back transfer of electrons to CdS and electrolyte than spin coating method. The open-circuit voltage increased to 0.59 V by introducing a ZnS layer through SILAR method. When ZnS NPs layer was deposited for 10 times on ZnO NRs, the conversion efficiency of QDSSC shows ∼3.3 folds increments of as-synthesized ZnO solar cell. - Graphical abstract: When ZnO nanorods were deposited by ZnS for 10 times, the conversion efficiency of QDSSC shows ∼3.3 folds increments of as-synthesized ZnO solar cell. Highlights: ► ZnS layers were deposited with two different ways. ► The way of SILAR is more beneficial for retarding the back transfer of electrons. ► The open-circuit voltage increased to 0.59 V by introducing a ZnS layer through SILAR method.

  14. Regulation of membrane excitability: a convergence on voltage-gated sodium conductance.

    Science.gov (United States)

    Lin, Wei-Hsiang; Baines, Richard A

    2015-02-01

    The voltage-gated sodium channel (Nav) plays a key role in regulation of neuronal excitability. Aberrant regulation of Nav expression and/or function can result in an imbalance in neuronal activity which can progress to epilepsy. Regulation of Nav activity is achieved by coordination of a multitude of mechanisms including RNA alternative splicing and translational repression. Understanding of these regulatory mechanisms is complicated by extensive genetic redundancy: the mammalian genome encodes ten Navs. By contrast, the genome of the fruitfly, Drosophila melanogaster, contains just one Nav homologue, encoded by paralytic (DmNa v ). Analysis of splicing in DmNa v shows variants exhibit distinct gating properties including varying magnitudes of persistent sodium current (INaP). Splicing by Pasilla, an identified RNA splicing factor, alters INaP magnitude as part of an activity-dependent mechanism. Enhanced INaP promotes membrane hyperexcitability that is associated with seizure-like behaviour in Drosophila. Nova-2, a mammalian Pasilla homologue, has also been linked to splicing of Navs and, moreover, mouse gene knockouts display seizure-like behaviour.Expression level of Navs is also regulated through a mechanism of translational repression in both flies and mammals. The translational repressor Pumilio (Pum) can bind to Na v transcripts and repress the normal process of translation, thus regulating sodium current (INa) density in neurons. Pum2-deficient mice exhibit spontaneous EEG abnormalities. Taken together, aberrant regulation of Nav function and/or expression is often epileptogenic. As such, a better understanding of regulation of membrane excitability through RNA alternative splicing and translational repression of Navs should provide new leads to treat epilepsy.

  15. Reciprocal regulation of reactive oxygen species and phospho-CREB regulates voltage gated calcium channel expression during Mycobacterium tuberculosis infection.

    Directory of Open Access Journals (Sweden)

    Arti Selvakumar

    Full Text Available Our previous work has demonstrated the roles played by L-type Voltage Gated Calcium Channels (VGCC in regulating Mycobacterium tuberculosis (M. tb survival and pathogenesis. Here we decipher mechanisms and pathways engaged by the pathogen to regulate VGCC expression in macrophages. We show that M. tb and its antigen Rv3416 use phospho-CREB (pCREB, Reactive Oxygen Species (ROS, Protein Kinase C (PKC and Mitogen Activated Protein Kinase (MAPK to modulate VGCC expression in macrophages. siRNA mediated knockdown of MyD88, IRAK1, IRAK2 or TRAF6 significantly inhibited antigen mediated VGCC expression. Inhibiting Protein Kinase C (PKC or MEK-ERK1/2 further increased VGCC expression. Interestingly, inhibiting intracellular calcium release upregulated antigen mediated VGCC expression, while inhibiting extracellular calcium influx had no significant effect. siRNA mediated knockdown of transcription factors c-Jun, SOX5 and CREB significantly inhibited Rv3416 mediated VGCC expression. A dynamic reciprocal cross-regulation between ROS and pCREB was observed that in turn governed VGCC expression with ROS playing a limiting role in the process. Further dissection of the mechanisms such as the interplay between ROS and pCREB would improve our understanding of the regulation of VGCC expression during M. tb infection.

  16. Programmable Voltage Regulating Method for 15 kV High Voltage DC Power Supply%15 kV高压直流电源的程控调压方法

    Institute of Scientific and Technical Information of China (English)

    肖剑锋; 陈新; 米彦

    2008-01-01

    In order to solve the disadvantages caused by mechanical slide rheostat that has big errors and low precision, a novel voltage regulation method for high voltage DC power supply was introduced. The key of this method were digital potentiometer MAXIM 5455 and linear photoelectric coupling LOC110, and application programs were compiled using Visual Basic which was graphical compiling language, furthermore the communication between exterior and computer was carried out by ICP7044D module, in consequence the output value of high voltage DC power supply could be regulated with computer. The measured results showed that this method could accurately, conveniently and rapidly regulate the output value of high voltage DC power supply.

  17. Online Estimation of Model Parameters and State of Charge of LiFePO4 Batteries Using a Novel Open-Circuit Voltage at Various Ambient Temperatures

    Directory of Open Access Journals (Sweden)

    Fei Feng

    2015-04-01

    Full Text Available This study describes an online estimation of the model parameters and state of charge (SOC of lithium iron phosphate batteries in electric vehicles. A widely used SOC estimator is based on the dynamic battery model with predeterminate parameters. However, model parameter variances that follow with their varied operation temperatures can result in errors in estimating battery SOC. To address this problem, a battery online parameter estimator is presented based on an equivalent circuit model using an adaptive joint extended Kalman filter algorithm. Simulations based on actual data are established to verify accuracy and stability in the regression of model parameters. Experiments are also performed to prove that the proposed estimator exhibits good reliability and adaptability under different loading profiles with various temperatures. In addition, open-circuit voltage (OCV is used to estimate SOC in the proposed algorithm. However, the OCV based on the proposed online identification includes a part of concentration polarization and hysteresis, which is defined as parametric identification-based OCV (OCVPI. Considering the temperature factor, a novel OCV–SOC relationship map is established by using OCVPI under various temperatures. Finally, a validating experiment is conducted based on the consecutive loading profiles. Results indicate that our method is effective and adaptable when a battery operates at different ambient temperatures.

  18. Open-circuit voltage enhancement on the basis of polymer gel electrolyte for a highly stable dye-sensitized solar cell.

    Science.gov (United States)

    Wu, Congcong; Jia, Lichao; Guo, Siyao; Han, Song; Chi, Bo; Pu, Jian; Jian, Li

    2013-08-28

    Dye-sensitized solar cells (DSSC) have received considerable attention owing to their low preparation cost and easy fabrication process. However, one of the drawbacks that limits the further application of DSSC is their poor stability, arising from the leakage and volatilization of the liquid organic solvent in the electrolyte. Therefore, to improve the long-term stability of DSSC, polymer gel electrolyte was studied to replace the conventional liquid electrolyte in this work. The results show that compared to liquid electrolyte, DSSC with polymer gel electrolyte has a smaller short-circuit current (Jsc), which decreases with the increase of the polymer gelator. Nevertheless, with the employment of the polymer gel electrolyte, there is a significant enhancement of open-circuit voltage (Voc), and it increases with the increase of the polymer gelator content. The highest Voc, up to 0.873 V, can be obtained for DSSC with a 30% polymer gelator content. The impact of the polymer gel electrolyte on the photovoltaic performance of DSSC, especially on Voc, was studied by analyzing the charge-transfer kinetics in the polymer gel electrolyte. Furthermore, the influence of the polymer gel electrolyte on the long-term stability of DSSC was also investigated.

  19. On-chip High-Voltage Generator Design

    CERN Document Server

    Tanzawa, Toru

    2013-01-01

    This book describes high-voltage generator design with switched-capacitor multiplier techniques.  The author provides various design techniques for switched-capacitor on-chip high-voltage generators, including charge pump circuits, regulators, level shifters, references, and oscillators.  Readers will see these techniques applied to system design in order to address the challenge of how the on-chip high-voltage generator is designed for Flash memories, LCD drivers, and other semiconductor devices to optimize the entire circuit area and power efficiency with a low voltage supply, while minimizing the cost.   ·         Shows readers how to design charge pump circuits with lower voltage operation, higher power efficiency, and smaller circuit area; ·         Describes comprehensive circuits and systems design of on-chip high-voltage generators; ·         Covers all the component circuit blocks, including charge pumps, pump regulators, level shifters, oscillators, and references.

  20. Relationship between Work Function of Hole Collection Electrode and Temperature Dependence of Open-Circuit Voltage in Multilayered Organic Solar Cells

    Science.gov (United States)

    Itoh, Eiji; Shirotori, Toshiki

    2012-02-01

    We have investigated the photovoltaic properties of multilayered organic photovoltaic devices consisting of indium tin oxide (ITO)/(NiO)/donor/C60/bathocuproine (BCP)/Al structures. Open circuit voltage (VOC) increases with the decrease in temperature between 40 and 350 K. The VOC was, however, pinned at approximately 0.6 V for the device without NiO, probably owing to the insufficient work-function difference between ITO and Al electrodes. The hole injection was also markedly suppressed at the ITO/donor interface in the device with large IP donor materials without the buffer layer and abnormal S-shaped current density-voltage (J-V) characteristics were observed. On the other hand, the value of VOC increases with the increase in ionization potential (IP) of donor materials in the device with NiO buffer layers owing to the enhanced work-function difference of about 1 eV, and the S-shaped curves disappeared at the high temperatures above 200 K. The VOC is further improved to nearly 1.2 V by the UV-ozone treatment of the NiO surface. We have therefore concluded that the increment of work function of the anode caused by the insertion of an oxide buffer layer and the surface treatment of the electrode by UV-ozone treatment are essentially important for the improvement of VOC and charge transport/injection properties in the multilayered organic solar cell applications.

  1. Dissection of neuronal gap junction circuits that regulate social behavior in Caenorhabditis elegans

    Science.gov (United States)

    Jang, Heeun; Levy, Sagi; Flavell, Steven W.; Mende, Fanny; Latham, Richard; Zimmer, Manuel; Bargmann, Cornelia I.

    2017-01-01

    A hub-and-spoke circuit of neurons connected by gap junctions controls aggregation behavior and related behavioral responses to oxygen, pheromones, and food in Caenorhabditis elegans. The molecular composition of the gap junctions connecting RMG hub neurons with sensory spoke neurons is unknown. We show here that the innexin gene unc-9 is required in RMG hub neurons to drive aggregation and related behaviors, indicating that UNC-9–containing gap junctions mediate RMG signaling. To dissect the circuit in detail, we developed methods to inhibit unc-9–based gap junctions with dominant-negative unc-1 transgenes. unc-1(dn) alters a stomatin-like protein that regulates unc-9 electrical signaling; its disruptive effects can be rescued by a constitutively active UNC-9::GFP protein, demonstrating specificity. Expression of unc-1(dn) in RMG hub neurons, ADL or ASK pheromone-sensing neurons, or URX oxygen-sensing neurons disrupts specific elements of aggregation-related behaviors. In ADL, unc-1(dn) has effects opposite to those of tetanus toxin light chain, separating the roles of ADL electrical and chemical synapses. These results reveal roles of gap junctions in a complex behavior at cellular resolution and provide a tool for similar exploration of other gap junction circuits. PMID:28143932

  2. A Decentralized Multivariable Robust Adaptive Voltage and Speed Regulator for Large-Scale Power Systems

    Science.gov (United States)

    Okou, Francis A.; Akhrif, Ouassima; Dessaint, Louis A.; Bouchard, Derrick

    2013-05-01

    This papter introduces a decentralized multivariable robust adaptive voltage and frequency regulator to ensure the stability of large-scale interconnnected generators. Interconnection parameters (i.e. load, line and transormer parameters) are assumed to be unknown. The proposed design approach requires the reformulation of conventiaonal power system models into a multivariable model with generator terminal voltages as state variables, and excitation and turbine valve inputs as control signals. This model, while suitable for the application of modern control methods, introduces problems with regards to current design techniques for large-scale systems. Interconnection terms, which are treated as perturbations, do not meet the common matching condition assumption. A new adaptive method for a certain class of large-scale systems is therefore introduces that does not require the matching condition. The proposed controller consists of nonlinear inputs that cancel some nonlinearities of the model. Auxiliary controls with linear and nonlinear components are used to stabilize the system. They compensate unknown parametes of the model by updating both the nonlinear component gains and excitation parameters. The adaptation algorithms involve the sigma-modification approach for auxiliary control gains, and the projection approach for excitation parameters to prevent estimation drift. The computation of the matrix-gain of the controller linear component requires the resolution of an algebraic Riccati equation and helps to solve the perturbation-mismatching problem. A realistic power system is used to assess the proposed controller performance. The results show that both stability and transient performance are considerably improved following a severe contingency.

  3. Damping improvement and terminal voltage regulation for a synchronous machine using an energy storage device

    Science.gov (United States)

    Kim, Seok-Kyoon; Song, Hwachang; Yoon, Tae-Woong

    2015-04-01

    On the basis of the non-linear third-order generator model, this article proposes a dual control scheme for a single synchronous machine equipped with an energy storage device to regulate the terminal voltage while enhancing the damping. Based on the input-output feedback linearisation method, the exciter controller is designed such that the terminal voltage robustly converges to its predetermined reference in the presence of a model uncertainty. In addition, the control input of the energy storage device feedbacks only the relative speed. It is shown that this controller can effectively increase the damping of the synchronous machine and that there is a set of initial conditions such that all trajectories started from this set go to the equilibrium point, satisfying input constraints. Moreover, it is also verified that all generator variables are bounded except for the power angle. The simulation results show that the closed-loop performance is satisfactory despite a transmission line fault and a model uncertainty in which the non-linear fourth-order generator model (two-axis) is used.

  4. Tuning of PID controller for an automatic regulator voltage system using chaotic optimization approach

    Energy Technology Data Exchange (ETDEWEB)

    Santos Coelho, Leandro dos [Pontifical Catholic University of Parana, PUCPR Industrial and Systems Engineering Graduate Program, LAS/PPGEPS Imaculada Conceicao, 1155, Zip code 80215-901, Curitiba, Parana (Brazil)], E-mail: leandro.coelho@pucpr.br

    2009-02-28

    Despite the popularity, the tuning aspect of proportional-integral-derivative (PID) controllers is a challenge for researchers and plant operators. Various controllers tuning methodologies have been proposed in the literature such as auto-tuning, self-tuning, pattern recognition, artificial intelligence, and optimization methods. Chaotic optimization algorithms as an emergent method of global optimization have attracted much attention in engineering applications. Chaotic optimization algorithms, which have the features of easy implementation, short execution time and robust mechanisms of escaping from local optimum, is a promising tool for engineering applications. In this paper, a tuning method for determining the parameters of PID control for an automatic regulator voltage (AVR) system using a chaotic optimization approach based on Lozi map is proposed. Since chaotic mapping enjoys certainty, ergodicity and the stochastic property, the proposed chaotic optimization introduces chaos mapping using Lozi map chaotic sequences which increases its convergence rate and resulting precision. Simulation results are promising and show the effectiveness of the proposed approach. Numerical simulations based on proposed PID control of an AVR system for nominal system parameters and step reference voltage input demonstrate the good performance of chaotic optimization.

  5. Characterization of the voltage control systems and speed of a synchronous machine of high power for short circuit testing; Caracterizacion de los sistemas de control de voltaje y velocidad de una maquina sincrona de alta potencia para pruebas de corto circuito

    Energy Technology Data Exchange (ETDEWEB)

    Segura Ozuna, Victor Octavio; Hernandez Rodriguez, Isaura Victoria; Alcaide Godinez, Indira Xochiquetzal; Garduno Ramirez, Raul; Montero Cervantes, Julio Cesar [Instituto de Investigaciones Electricas, Cuernavaca, Morelos (Mexico); Ruiz Rodriguez, Genaro; Martinez Torres; Ricardo [CFE-LAPEM, Irapuato, Guanajuato (Mexico)

    2012-07-01

    This paper introduces a characterization of the behavior of the speed and voltage control systems of a special purpose synchronous machine (GCC) based on measuring and monitoring physical signals, and recording of the sampled waveforms. Basically, the GCC supplies the energy to perform high-power short-circuits tests to certify electrical equipment and components, as required by the Comision Federal de Electricidad (CFE) in Mexico. The GCC operates alternately as motor and generator. With the GCC operating as motor, speed control during startup, acceleration, re-acceleration and braking is carried out by a static frequency converter (SFC). Complementary, the voltage controller manipulates excitation power to control terminal voltage when the GCC operates as generator and regulates excitation current when the GCC operates as motor. Compared to conventional voltage regulation systems, which must go off in case of short-circuit, the GCC voltage regulator must keep controlling field excitation to maintain the required line current and terminal voltage during short-circuit tests. Monitoring of physical signals was carried out with a portable data acquisition system based on SCXI and PXI digital platforms. A total of 78 signals were monitored with a 6 kHz sampling rate that was enough to obtain detailed signal waveforms. Data captured was processed and plotted for analysis. The signal graphs show the current real behavior of both, the voltage control system and the speed control system, and constitute a precise characterization of their behavior. [Spanish] Este documento presenta una caracterizacion del comportamiento de los sistemas de control de velocidad y voltaje de una maquina sincrona de proposito especial (GCC) basada en la medicion y monitoreo de senales fisicas, asi como en el registro de las formas de onda muestreadas. Basicamente, la GCC suministra la energia para efectuar pruebas de corto circuito de alta potencia para certificar equipo y componentes

  6. Starting Circuit For Erasable Programmable Logic Device

    Science.gov (United States)

    Cole, Steven W.

    1990-01-01

    Voltage regulator bypassed to supply starting current. Starting or "pullup" circuit supplies large inrush of current required by erasable programmable logic device (EPLD) while being turned on. Operates only during such intervals of high demand for current and has little effect any other time. Performs needed bypass, acting as current-dependent shunt connecting battery or other source of power more nearly directly to EPLD. Input capacitor of regulator removed when starting circuit installed, reducing probability of damage to transistor in event of short circuit in or across load.

  7. The Eag domain regulates the voltage-dependent inactivation of rat Eag1 K+ channels.

    Directory of Open Access Journals (Sweden)

    Ting-Feng Lin

    Full Text Available Eag (Kv10 and Erg (Kv11 belong to two distinct subfamilies of the ether-à-go-go K+ channel family (KCNH. While Erg channels are characterized by an inward-rectifying current-voltage relationship that results from a C-type inactivation, mammalian Eag channels display little or no voltage-dependent inactivation. Although the amino (N-terminal region such as the eag domain is not required for the C-type inactivation of Erg channels, an N-terminal deletion in mouse Eag1 has been shown to produce a voltage-dependent inactivation. To further discern the role of the eag domain in the inactivation of Eag1 channels, we generated N-terminal chimeras between rat Eag (rEag1 and human Erg (hERG1 channels that involved swapping the eag domain alone or the complete cytoplasmic N-terminal region. Functional analyses indicated that introduction of the homologous hERG1 eag domain led to both a fast phase and a slow phase of channel inactivation in the rEag1 chimeras. By contrast, the inactivation features were retained in the reverse hERG1 chimeras. Furthermore, an eag domain-lacking rEag1 deletion mutant also showed the fast phase of inactivation that was notably attenuated upon co-expression with the rEag1 eag domain fragment, but not with the hERG1 eag domain fragment. Additionally, we have identified a point mutation in the S4-S5 linker region of rEag1 that resulted in a similar inactivation phenotype. Biophysical analyses of these mutant constructs suggested that the inactivation gating of rEag1 was distinctly different from that of hERG1. Overall, our findings are consistent with the notion that the eag domain plays a critical role in regulating the inactivation gating of rEag1. We propose that the eag domain may destabilize or mask an inherent voltage-dependent inactivation of rEag1 K+ channels.

  8. Power Generation and Voltage Regulation of 132KV Karbala grid using DFIG Wind Turbine Generator

    Directory of Open Access Journals (Sweden)

    Qasim Kamil Mohsin

    2015-06-01

    Full Text Available Due to increasing demand on electrical energy in Iraq and to have clean energy that is environmental friendly, wind energy would be one of the most important and promising sources of renewable energy to achieve this goal. This paper discussed the reasons to use the Doubly-Feed Induction Generator (DFIG amongst the available types of wind turbine generators, and in section (III illustrate Motivations to select place to the wind farm construction. using decupling method (the vector control strategy to change reactive power of DFIG 2MW connected to middle of the 132KV transmission line (Karbala north – Alahkader without effect about the active power generated from DFIG itself with fixed wind speed value assumed to provide the voltage regulation, and control of the transmission line In addition to power generating. By using PSCAD/EMTDC, different simulation results are presented based on various scenarios.

  9. Regulation of KCNQ/Kv7 family voltage-gated K(+) channels by lipids.

    Science.gov (United States)

    Taylor, Keenan C; Sanders, Charles R

    2017-04-01

    Many years of studies have established that lipids can impact membrane protein structure and function through bulk membrane effects, by direct but transient annular interactions with the bilayer-exposed surface of protein transmembrane domains, and by specific binding to protein sites. Here, we focus on how phosphatidylinositol 4,5-bisphosphate (PIP2) and polyunsaturated fatty acids (PUFAs) impact ion channel function and how the structural details of the interactions of these lipids with ion channels are beginning to emerge. We focus on the Kv7 (KCNQ) subfamily of voltage-gated K(+) channels, which are regulated by both PIP2 and PUFAs and play a variety of important roles in human health and disease. This article is part of a Special Issue entitled: Lipid order/lipid defects and lipid-control of protein activity edited by Dirk Schneider.

  10. Towards a Unified Theory of Calmodulin Regulation (Calmodulation) of Voltage-Gated Calcium and Sodium Channels.

    Science.gov (United States)

    Ben-Johny, Manu; Dick, Ivy E; Sang, Lingjie; Limpitikul, Worawan B; Kang, Po Wei; Niu, Jacqueline; Banerjee, Rahul; Yang, Wanjun; Babich, Jennifer S; Issa, John B; Lee, Shin Rong; Namkung, Ho; Li, Jiangyu; Zhang, Manning; Yang, Philemon S; Bazzazi, Hojjat; Adams, Paul J; Joshi-Mukherjee, Rosy; Yue, Daniel N; Yue, David T

    2015-01-01

    Voltage-gated Na and Ca(2+) channels represent two major ion channel families that enable myriad biological functions including the generation of action potentials and the coupling of electrical and chemical signaling in cells. Calmodulin regulation (calmodulation) of these ion channels comprises a vital feedback mechanism with distinct physiological implications. Though long-sought, a shared understanding of the channel families remained elusive for two decades as the functional manifestations and the structural underpinnings of this modulation often appeared to diverge. Here, we review recent advancements in the understanding of calmodulation of Ca(2+) and Na channels that suggest a remarkable similarity in their regulatory scheme. This interrelation between the two channel families now paves the way towards a unified mechanistic framework to understand vital calmodulin-dependent feedback and offers shared principles to approach related channelopathic diseases. An exciting era of synergistic study now looms.

  11. Voltage gated calcium channels negatively regulate protective immunity to Mycobacterium tuberculosis.

    Directory of Open Access Journals (Sweden)

    Shashank Gupta

    Full Text Available Mycobacterium tuberculosis modulates levels and activity of key intracellular second messengers to evade protective immune responses. Calcium release from voltage gated calcium channels (VGCC regulates immune responses to pathogens. In this study, we investigated the roles of VGCC in regulating protective immunity to mycobacteria in vitro and in vivo. Inhibiting L-type or R-type VGCC in dendritic cells (DCs either using antibodies or by siRNA increased calcium influx in an inositol 1,4,5-phosphate and calcium release calcium activated channel dependent mechanism that resulted in increased expression of genes favoring pro-inflammatory responses. Further, VGCC-blocked DCs activated T cells that in turn mediated killing of M. tuberculosis inside macrophages. Likewise, inhibiting VGCC in infected macrophages and PBMCs induced calcium influx, upregulated the expression of pro-inflammatory genes and resulted in enhanced killing of intracellular M. tuberculosis. Importantly, compared to healthy controls, PBMCs of tuberculosis patients expressed higher levels of both VGCC, which were significantly reduced following chemotherapy. Finally, blocking VGCC in vivo in M. tuberculosis infected mice using specific antibodies increased intracellular calcium and significantly reduced bacterial loads. These results indicate that L-type and R-type VGCC play a negative role in M. tuberculosis infection by regulating calcium mobilization in cells that determine protective immunity.

  12. Regulation of voltage-gated potassium channels by PI(4,5)P2.

    Science.gov (United States)

    Kruse, Martin; Hammond, Gerald R V; Hille, Bertil

    2012-08-01

    Phosphatidylinositol 4,5-bisphosphate (PI(4,5)P(2)) regulates activities of numerous ion channels including inwardly rectifying potassium (K(ir)) channels, KCNQ, TRP, and voltage-gated calcium channels. Several studies suggest that voltage-gated potassium (K(V)) channels might be regulated by PI(4,5)P(2). Wide expression of K(V) channels in different cells suggests that such regulation could have broad physiological consequences. To study regulation of K(V) channels by PI(4,5)P(2), we have coexpressed several of them in tsA-201 cells with a G protein-coupled receptor (M(1)R), a voltage-sensitive lipid 5-phosphatase (Dr-VSP), or an engineered fusion protein carrying both lipid 4-phosphatase and 5-phosphatase activity (pseudojanin). These tools deplete PI(4,5)P(2) with application of muscarinic agonists, depolarization, or rapamycin, respectively. PI(4,5)P(2) at the plasma membrane was monitored by Förster resonance energy transfer (FRET) from PH probes of PLCδ1 simultaneously with whole-cell recordings. Activation of Dr-VSP or recruitment of pseudojanin inhibited K(V)7.1, K(V)7.2/7.3, and K(ir)2.1 channel current by 90-95%. Activation of M(1)R inhibited K(V)7.2/7.3 current similarly. With these tools, we tested for potential PI(4,5)P(2) regulation of activity of K(V)1.1/K(V)β1.1, K(V)1.3, K(V)1.4, and K(V)1.5/K(V)β1.3, K(V)2.1, K(V)3.4, K(V)4.2, K(V)4.3 (with different KChIPs and DPP6-s), and hERG/KCNE2. Interestingly, we found a substantial removal of inactivation for K(V)1.1/K(V)β1.1 and K(V)3.4, resulting in up-regulation of current density upon activation of M(1)R but no changes in activity upon activating only VSP or pseudojanin. The other channels tested except possibly hERG showed no alteration in activity in any of the assays we used. In conclusion, a depletion of PI(4,5)P(2) at the plasma membrane by enzymes does not seem to influence activity of most tested K(V) channels, whereas it does strongly inhibit members of the K(V)7 and K(ir) families.

  13. Analog circuit design designing waveform processing circuits

    CERN Document Server

    Feucht, Dennis

    2010-01-01

    The fourth volume in the set Designing Waveform-Processing Circuits builds on the previous 3 volumes and presents a variety of analog non-amplifier circuits, including voltage references, current sources, filters, hysteresis switches and oscilloscope trigger and sweep circuitry, function generation, absolute-value circuits, and peak detectors.

  14. Regulation of voltage-gated sodium current by endogenous Src family kinases in cochlear spiral ganglion neurons in culture.

    Science.gov (United States)

    Feng, Shuang; Pflueger, Melissa; Lin, Shuang-Xiu; Groveman, Bradley R; Su, Jiping; Yu, Xian-Min

    2012-04-01

    Voltage-gated sodium (Na+) and potassium (K+)channels have been found to be regulated by Src family kinases(SFKs).However, how these channels are regulated by SFKs in cochlear spiral ganglion neurons (SGNs) remains unknown.Here, we report that altering the activity of endogenous SFKs modulated voltage-gated Na+, but not K+, currents recorded in embryonic SGNs in culture. Voltage-gated Na+ current was suppressed by inhibition of endogenous SFKs or just Src and potentiated by the activation of these enzymes. Detailed investigations showed that under basal conditions, SFK inhibitor application did not significantly affect the voltage-dependent activation, but shifted the steady-state inactivation curves of Na+ currents and delayed the recovery of Na+ currents from inactivation. Application of Src specific inhibitor, Src40–58,not only shifted the inactivation curve but also delayed the recovery of Na+ currents and moved the voltage-dependent activation curve towards the left. The pre-inhibition of SFKs occluded all the effects induced by Src40–58 application, except the left shift of the activation curve. The activation of SFKs did not change either steady-state inactivation or recovery of Na+ currents, but caused the left shift of the activation curve.SFK inhibitor application effectively prevented all the effects induced by SFK activation, suggesting that both the voltage-dependent activation and steady-state inactivation of Na+ current are subjects of SFK regulation. The different effects induced by activation versus inhibition of SFKs implied that under basal conditions, endogenously active and inactive SFKs might be differentially involved in the regulation of voltage-gated Na+ channels in SGNs.

  15. SF6高压断路器检测维护策略研究%Research on the detection and maintenance strategy of SF6 high voltage circuit breaker

    Institute of Scientific and Technical Information of China (English)

    孙勇军

    2016-01-01

    SF6高压断路器是利用六氟化硫气体作为灭弧介质和绝缘介质的一种断路器,由于SF6气体的优异性能,使其在应用过程中具备明显的优势.鉴于此,本文主要分析SF6高压断路器的检测维护策略.%SF6 high voltage circuit breaker is a circuit breaker which uses six sulfur fluoride gas as arc extinguishing media and insulating medium,which has obvious advantages in the application process because of the excellent performance of SF6 gas.In view of this,this paper mainly analyzes the SF6 high voltage circuit breaker testing and maintenance strategy.

  16. A Low Voltage High PSRR Reference Source Based on Regulated Current Mode Structure%基于电流控制模式的低压、高PSRR基准源

    Institute of Scientific and Technical Information of China (English)

    张慧敏; 周云; 王璐霞; 袁凯

    2011-01-01

    A new bandgap voltage reference circuit with low voltage .high power supply rejection ratio (PSRR) based on a regulated current mode structure is presented. The proposed circuit utilizes a regulated current mode structure and some feedback loops to improve the overall PSRR. Using resistive subdivision reaches a low voltage and provides the bias voltage of transistors,simplified bias circuit. The circuit was designed with 0. 5μn complementary metal oxide semiconductor transistor (CMOS) N - well technology, which worked at 1.5V power voltage. Cadence Spectre simulation results show PSRR is 107dB at low frequencies, the temperature coefficient from - 10°C to 125°C temperature range is 7.17 ppm/°C and the power consumption is only 0. 525mW. This circuit shows robustness against process variation.%基于可调电流控制模式设计出一种低压、高电源抑制比的带隙基准电压源电路.采用电流控制模式和多反馈环路,提高电路的整体电源抑制比;通过电阻分压的方式,使电路达到低压,同时提供偏压,简化偏置电路.采用0.5μmCMOS N阱工艺,电路可在电源电压为1.5V时正常工作.使用Cadence Spectre进行仿真结果表明,低频时电源抑制比(PSRR)高达107dB.- 10℃~125℃温度范围内,平均温度系数约7.17ppm/℃,功耗仅为0.525mW.此电路能有效地抑制制程变异.

  17. Transient Voltage Recorder

    Science.gov (United States)

    Medelius, Pedro J. (Inventor); Simpson, Howard J. (Inventor)

    2002-01-01

    A voltage transient recorder can detect lightning induced transient voltages. The recorder detects a lightning induced transient voltage and adjusts input amplifiers to accurately record transient voltage magnitudes. The recorder stores voltage data from numerous monitored channels, or devices. The data is time stamped and can be output in real time, or stored for later retrieval. The transient recorder, in one embodiment, includes an analog-to-digital converter and a voltage threshold detector. When an input voltage exceeds a pre-determined voltage threshold, the recorder stores the incoming voltage magnitude and time of arrival. The recorder also determines if its input amplifier circuits clip the incoming signal or if the incoming signal is too low. If the input data is clipped or too low, the recorder adjusts the gain of the amplifier circuits to accurately acquire subsequent components of the lightning induced transients.

  18. Capacitor-voltage converter circuit based on CMOS%基于CMOS的电容-电压转换电路的设计

    Institute of Scientific and Technical Information of China (English)

    曹俊杰; 邱成军

    2013-01-01

    在MEMS传感器的电容检测电路中,经常要采用电容—电压转换电路.本研究将两相不交叠时钟模块应用到设计中,使得该电路用单个时钟就能进行有效控制,并能够满足MEMS电容检测系统的要求.采用0.25 μm工艺库对电路进行优化并给定了电路仿真的相应结论.仿真结果表明,其CMOS运放部分的增益为77.76 dB,单位增益带宽为5.60 MHz,相位裕量为65.87°,输出摆幅为-2.0~1.89 V,输入共模范围为-1.0 ~1.93V,正摆率为+9.92 V·μs-1,负摆率为5.03 V·μs-,功耗为1.03 mW.该电路适合于pF量级范围内的电容变化,该变化范围为35~1 200 pF,且输出线性度良好.%In the MEMS sensor capacitance detection of circuit,capacitive-voltage conversion circuit is often used.Two phase non-overlapping clock module has been applied to the design,so the circuit can be effectively controlled by a single clock and also be satisfied to the requirements of MEMS capacitive detection system.Using 0.25 μm technology library to optimize the circuit,the appropriate conclusions have been given out to the circuit simulation.The results show that part of its CMOS opamp is gain of 77.76 dB,the bandwidth of unity gain is 5.60 MHz,the phase margin is 65.87°,the output swing is-2.0 ~ 1.89 V,the input common mode range is-1.0 ~ 1.93 V,the positive slew rate is 9.92 V · μ S-1,the negative slew rate is 5.03 V · μ s-1,the power consumption is 1.03 mW.The circuit is suitable for capacitance change in the order of pF within the range of 35 ~ 1 200 pF,and the output is in good linearity.

  19. Current view on regulation of voltage-gated sodium channels by calcium and auxiliary proteins.

    Science.gov (United States)

    Pitt, Geoffrey S; Lee, Seok-Yong

    2016-09-01

    In cardiac and skeletal myocytes, and in most neurons, the opening of voltage-gated Na(+) channels (NaV channels) triggers action potentials, a process that is regulated via the interactions of the channels' intercellular C-termini with auxiliary proteins and/or Ca(2+) . The molecular and structural details for how Ca(2+) and/or auxiliary proteins modulate NaV channel function, however, have eluded a concise mechanistic explanation and details have been shrouded for the last decade behind controversy about whether Ca(2+) acts directly upon the NaV channel or through interacting proteins, such as the Ca(2+) binding protein calmodulin (CaM). Here, we review recent advances in defining the structure of NaV intracellular C-termini and associated proteins such as CaM or fibroblast growth factor homologous factors (FHFs) to reveal new insights into how Ca(2+) affects NaV function, and how altered Ca(2+) -dependent or FHF-mediated regulation of NaV channels is perturbed in various disease states through mutations that disrupt CaM or FHF interaction.

  20. Regulation of mitochondrial function by voltage dependent anion channels in ethanol metabolism and the Warburg effect.

    Science.gov (United States)

    Lemasters, John J; Holmuhamedov, Ekhson L; Czerny, Christoph; Zhong, Zhi; Maldonado, Eduardo N

    2012-06-01

    Voltage dependent anion channels (VDAC) are highly conserved proteins that are responsible for permeability of the mitochondrial outer membrane to hydrophilic metabolites like ATP, ADP and respiratory substrates. Although previously assumed to remain open, VDAC closure is emerging as an important mechanism for regulation of global mitochondrial metabolism in apoptotic cells and also in cells that are not dying. During hepatic ethanol oxidation to acetaldehyde, VDAC closure suppresses exchange of mitochondrial metabolites, resulting in inhibition of ureagenesis. In vivo, VDAC closure after ethanol occurs coordinately with mitochondrial uncoupling. Since acetaldehyde passes through membranes independently of channels and transporters, VDAC closure and uncoupling together foster selective and more rapid oxidative metabolism of toxic acetaldehyde to nontoxic acetate by mitochondrial aldehyde dehydrogenase. In single reconstituted VDAC, tubulin decreases VDAC conductance, and in HepG2 hepatoma cells, free tubulin negatively modulates mitochondrial membrane potential, an effect enhanced by protein kinase A. Tubulin-dependent closure of VDAC in cancer cells contributes to suppression of mitochondrial metabolism and may underlie the Warburg phenomenon of aerobic glycolysis. This article is part of a Special Issue entitled: VDAC structure, function, and regulation of mitochondrial metabolism.

  1. KCNE1 and KCNE3: The yin and yang of voltage-gated K(+) channel regulation.

    Science.gov (United States)

    Abbott, Geoffrey W

    2016-01-15

    The human KCNE gene family comprises five genes encoding single transmembrane-spanning ion channel regulatory subunits. The primary function of KCNE subunits appears to be regulation of voltage-gated potassium (Kv) channels, and the best-understood KCNE complexes are with the KCNQ1 Kv α subunit. Here, we review the often opposite effects of KCNE1 and KCNE3 on Kv channel biology, with an emphasis on regulation of KCNQ1. Slow-activating IKs channel complexes formed by KCNQ1 and KCNE1 are essential for human ventricular myocyte repolarization, while constitutively active KCNQ1-KCNE3 channels are important in the intestine. Inherited sequence variants in human KCNE1 and KCNE3 cause cardiac arrhythmias but by different mechanisms, and each is important for hearing in unique ways. Because of their contrasting effects on KCNQ1 function, KCNE1 and KCNE3 have proved invaluable tools in the mechanistic understanding of how channel gating can be manipulated, and each may also provide a window into novel insights and new therapeutic opportunities in K(+) channel pharmacology. Finally, findings from studies of Kcne1(-/-) and Kcne3(-/-) mouse lines serve to illustrate the complexity of KCNE biology and KCNE-linked disease states.

  2. Transformerless DC-DC Converter Using Cockcroft-Walton Voltage Multiplier to Obtain High DC Voltage

    Directory of Open Access Journals (Sweden)

    Meghana G Naik,

    2014-11-01

    Full Text Available In the present scenario the use of transformer for high voltages in converter circuit reduces the overall operating efficiency due to leakage inductance and use of transformer also increases the operational cost. . Therefore the proposed system is implemented with transformer less DC-DC converter so as to obtain high DC voltage with the use of nine stage Cockcroft-Walton (CW voltage multiplier. The proposed converter operates in CCM (continuous conduction mode, so that the converter switch stress, the switching losses are reduced. The DC voltage at the input of the proposed model is low and is boosted up by boost inductor (Ls in DC-DC converter stage and performs inverter operation. The number of stages in CW-voltage multiplier circuit is applied with low input pulsating DC (AC Voltage voltage where it is getting converted to high DC output voltage. The proposed converter switches operates at two independent frequencies, modulating (fsm andalternating (fsc frequency. The fsm operates at higher frequency of the output while the fsc operates at lower frequency of the desired output voltage ripple and the output ripples can be adjusted by the switch Sc1 and Sc2. The regulation of the output voltage is achieved by controlling the Duty ratio.The simulation is carried over by the MATLABSIMULINK.

  3. Mixed voltage VLSI design

    Science.gov (United States)

    Panwar, Ramesh; Rennels, David; Alkalaj, Leon

    1993-01-01

    A technique for minimizing the power dissipated in a Very Large Scale Integration (VLSI) chip by lowering the operating voltage without any significant penalty in the chip throughput even though low voltage operation results in slower circuits. Since the overall throughput of a VLSI chip depends on the speed of the critical path(s) in the chip, it may be possible to sustain the throughput rates attained at higher voltages by operating the circuits in the critical path(s) with a high voltage while operating the other circuits with a lower voltage to minimize the power dissipation. The interface between the gates which operate at different voltages is crucial for low power dissipation since the interface may possibly have high static current dissipation thus negating the gains of the low voltage operation. The design of a voltage level translator which does the interface between the low voltage and high voltage circuits without any significant static dissipation is presented. Then, the results of the mixed voltage design using a greedy algorithm on three chips for various operating voltages are presented.

  4. Enhancement of open-circuit voltage on organic photovoltaic devices by Al-doped TiO{sub 2} modifying layer produced by sol–gel method

    Energy Technology Data Exchange (ETDEWEB)

    Valaski, R.; Arantes, C.; Senna, C.A.; Carôzo, Victor; Achete, C.A. [Materials Metrology Division, Instituto Nacional de Metrologia, Qualidade e Tecnologia, Xerém, Duque de Caxias 25250-020, RJ (Brazil); Cremona, M., E-mail: cremona@fis.puc-rio.br [Materials Metrology Division, Instituto Nacional de Metrologia, Qualidade e Tecnologia, Xerém, Duque de Caxias 25250-020, RJ (Brazil); Physics Department, Pontifícia Universidade Católica do Rio de Janeiro, Rio de Janeiro 22453-970, RJ (Brazil)

    2014-12-01

    Sol–gel method has shown several advantages for oxide synthesis, such as lower cost production, coating large areas, lower processing temperatures and ease insertion of doping materials. Therefore, it is attractive for production of intermediate and electrode modifying layers in organic optoelectronic devices. Herein, spin-coated aluminum-doped titanium dioxide (AlTiO{sub 2}) thin films were produced by sol–gel method onto glass and fluorine-doped tin oxide (FTO) substrates, using different Al-dopant concentrations and post-done annealing temperatures. Electrical measurements were performed in order to investigate the improvement of the TiO{sub 2} resistivity. Additionally, structural, compositional, morphological, optical and electrical properties of the optimal AlTiO{sub 2} modifying layers onto FTO substrates were probed by different techniques, and compared with those obtained from the undoped thin films produced under similar conditions. Organic photovoltaic devices (OPVs) with the structure FTO/AlTiO{sub 2}(30 nm)/C{sub 60}(50 nm)/CuPc(50 nm)/Al with an Al concentration of 0.03 M in AlTiO{sub 2} layer were produced. The insertion of AlTiO{sub 2} thin films improved the short-circuit current density (J{sub sc}) as well as the open circuit voltage (V{sub oc}) in comparison with non-modified electrode FTO based devices. This behavior is discussed in terms of induced interface phenomena as dipole formation induced by Al. - Highlights: • Easy and cheap solution-process for AlTiO{sub 2} modification of FTO electrode for OPVs • Electrical, structural and optical characterization of TiO{sub 2} layers with Al-dopant • Improvement of Voc and Jsc of inverted OPVs with AlTiO{sub 2} modified electrode.

  5. Thieno[3,4-c]Pyrrole-4,6-Dione-Based Polymer Acceptors for High Open-Circuit Voltage All-Polymer Solar Cells

    KAUST Repository

    Liu, Shengjian

    2017-04-20

    While polymer acceptors are promising fullerene alternatives in the fabrication of efficient bulk heterojunction (BHJ) solar cells, the range of efficient material systems relevant to the “all-polymer” BHJ concept remains narrow, and currently limits the perspectives to meet the 10% efficiency threshold in all-polymer solar cells. This report examines two polymer acceptor analogs composed of thieno[3,4-c]pyrrole-4,6-dione (TPD) and 3,4-difluorothiophene ([2F]T) motifs, and their BHJ solar cell performance pattern with a low-bandgap polymer donor commonly used with fullerenes (PBDT-TS1; taken as a model system). In this material set, the introduction of a third electron-deficient motif, namely 2,1,3-benzothiadiazole (BT), is shown to (i) significantly narrow the optical gap (Eopt) of the corresponding polymer (by ≈0.2 eV) and (ii) improve the electron mobility of the polymer by over two orders of magnitude in BHJ solar cells. In turn, the narrow-gap P2TPDBT[2F]T analog (Eopt = 1.7 eV) used as fullerene alternative yields high open-circuit voltages (VOC) of ≈1.0 V, notable short-circuit current values (JSC) of ≈11.0 mA cm−2, and power conversion efficiencies (PCEs) nearing 5% in all-polymer BHJ solar cells. P2TPDBT[2F]T paves the way to a new, promising class of polymer acceptor candidates.

  6. Improved open-circuit voltage in Cu(In,Ga)Se{sub 2} solar cells with high work function transparent electrodes

    Energy Technology Data Exchange (ETDEWEB)

    Jäger, Timo, E-mail: timo.jaeger@empa.ch; Romanyuk, Yaroslav E.; Bissig, Benjamin; Pianezzi, Fabian; Nishiwaki, Shiro; Reinhard, Patrick; Steinhauser, Jérôme; Tiwari, Ayodhya N. [Empa—Swiss Federal Laboratories for Materials Science and Technology, Laboratory for Thin Films and Photovoltaics, Überlandstrasse 129, 8600 Dübendorf (Switzerland); Schwenk, Johannes [Empa—Swiss Federal Laboratories for Materials Science and Technology, Laboratory for Nanoscale Materials Science, Überlandstrasse 129, 8600 Dübendorf (Switzerland)

    2015-06-14

    Hydrogenated indium oxide (IOH) is implemented as transparent front contact in Cu(In,Ga)Se{sub 2} (CIGS) solar cells, leading to an open circuit voltage V{sub OC} enhanced by ∼20 mV as compared to reference devices with ZnO:Al (AZO) electrodes. This effect is reproducible in a wide range of contact sheet resistances corresponding to various IOH thicknesses. We present the detailed electrical characterization of glass/Mo/CIGS/CdS/intrinsic ZnO (i-ZnO)/transparent conductive oxide (TCO) with different IOH/AZO ratios in the front TCO contact in order to identify possible reasons for the enhanced V{sub OC}. Temperature and illumination intensity-dependent current-voltage measurements indicate that the dominant recombination path does not change when AZO is replaced by IOH, and it is mainly limited to recombination in the space charge region and at the junction interface of the solar cell. The main finding is that the introduction of even a 5 nm-thin IOH layer at the i-ZnO/TCO interface already results in a step-like increase in V{sub OC}. Two possible explanations are proposed and verified by one-dimensional simulations using the SCAPS software. First, a higher work function of IOH as compared to AZO is simulated to yield an V{sub OC} increase by 21 mV. Second, a lower defect density in the i-ZnO layer as a result of the reduced sputter damage during milder sputter-deposition of IOH can also add to a maximum enhanced V{sub OC} of 25 mV. Our results demonstrate that the proper choice of the front TCO contact can reduce the parasitic recombination and boost the efficiency of CIGS cells with improved corrosion stability.

  7. Voltage Mode-to-Current Mode Transformation

    Directory of Open Access Journals (Sweden)

    Tejmal S. Rathore

    2012-10-01

    Full Text Available This paper proposes a procedure for converting a class of Op Amp-, FTFN-, CC- and CFAbased voltage mode circuits to corresponding current mode circuits without requiring any additional circuit elements and finally from Op Amp-based voltage mode circuits to any of the FTFN, CC and CFA current mode circuits. The latter circuits perform better at high frequency than the former ones. The validity of the transformation has been checked on simulated circuits with PSPICE.

  8. Kv3 voltage-gated potassium channels regulate neurotransmitter release from mouse motor nerve terminals.

    Science.gov (United States)

    Brooke, Ruth E; Moores, Thomas S; Morris, Neil P; Parson, Simon H; Deuchars, Jim

    2004-12-01

    Voltage-gated potassium (Kv) channels are critical to regulation of neurotransmitter release throughout the nervous system but the roles and identity of the subtypes involved remain unclear. Here we show that Kv3 channels regulate transmitter release at the mouse neuromuscular junction (NMJ). Light- and electron-microscopic immunohistochemistry revealed Kv3.3 and Kv3.4 subunits within all motor nerve terminals of muscles examined [transversus abdominus, lumbrical and flexor digitorum brevis (FDB)]. To determine the roles of these Kv3 subunits, intracellular recordings were made of end-plate potentials (EPPs) in FDB muscle fibres evoked by electrical stimulation of tibial nerve. Tetraethylammonium (TEA) applied at low concentrations (0.05-0.5 mM), which blocks only a few known potassium channels including Kv3 channels, did not affect muscle fibre resting potential but significantly increased the amplitude of all EPPs tested. Significantly, this effect of TEA was still observed in the presence of the large-conductance calcium-activated potassium channel blockers iberiotoxin (25-150 nM) and Penitrem A (100 nM), suggesting a selective action on Kv3 subunits. Consistent with this, 15-microM 4-aminopyridine, which blocks Kv3 but not large-conductance calcium-activated potassium channels, enhanced evoked EPP amplitude. Unexpectedly, blood-depressing substance-I, a toxin selective for Kv3.4 subunits, had no effect at 0.05-1 microM. The combined presynaptic localization of Kv3 subunits and pharmacological enhancement of EPP amplitude indicate that Kv3 channels regulate neurotransmitter release from presynaptic terminals at the NMJ.

  9. Developmental regulation of voltage-sensitive sodium channels in rat skeletal muscle

    Energy Technology Data Exchange (ETDEWEB)

    Sherman, S.J.

    1985-01-01

    The developmental regulation of the voltage-sensitive Na/sup +/ channel in rat skeletal muscle was studied in vivo and in vitro. In triceps surae muscle developing in vivo the development of TTX-sensitive Na/sup +/ channel occurred primarily during the first three postnatal weeks as determined by the specific binding of (/sup 3/H)saxitoxin. This development proceeded in two separate phases. The first phase occurs independently of continuing motor neuron innervation and accounts for 60% of the adult density of TTX-sensitive Na/sup +/ channels. The second phase, which begins about day 11, requires innervation. Muscle cells in primary culture were found to have both TTX-sensitive and insensitive Na/sup +/ channels. The development of the TTX-sensitive channel, in vitro, paralleled the initial innervation-independent phase of development observed in vivo. The density of TTX-sensitive Na/sup +/ channels in cultured muscle cells was regulated by electrical activity and cytosolic Ca/sup + +/ levels. Pharmacological blockade of the spontaneous electrical activity present in these cells lead to a nearly 2-fold increase in the surface density of TTX-sensitive channels. The turnover time of the TTX-sensitive Na/sup +/ channel was measured by blocking the incorporation of newly synthesized channels with tunicamycin, an inhibitor of N-linked protein glycosylation. The regulation of channel density by electrical activity, cytosolic Ca/sup + +/levels, and agents affecting cyclic neucleotide levels had no effect on the turnover time of the TTX-sensitive Na/sup +/ channel, indicating that these regulatory agents instead affect the synthesis of the channel.

  10. Differential CaMKII regulation by voltage-gated calcium channels in the striatum.

    Science.gov (United States)

    Pasek, Johanna G; Wang, Xiaohan; Colbran, Roger J

    2015-09-01

    Calcium signaling regulates synaptic plasticity and many other functions in striatal medium spiny neurons to modulate basal ganglia function. Ca(2+)/calmodulin-dependent protein kinase II (CaMKII) is a major calcium-dependent signaling protein that couples calcium entry to diverse cellular changes. CaMKII activation results in autophosphorylation at Thr286 and sustained calcium-independent CaMKII activity after calcium signals dissipate. However, little is known about the mechanisms regulating striatal CaMKII. To address this, mouse brain slices were treated with pharmacological modulators of calcium channels and punches of dorsal striatum were immunoblotted for CaMKII Thr286 autophosphorylation as an index of CaMKII activation. KCl depolarization increased levels of CaMKII autophosphorylation ~2-fold; this increase was blocked by an LTCC antagonist and was mimicked by treatment with pharmacological LTCC activators. The chelation of extracellular calcium robustly decreased basal CaMKII autophosphorylation within 5min and increased levels of total CaMKII in cytosolic fractions, in addition to decreasing the phosphorylation of CaMKII sites in the GluN2B subunit of NMDA receptors and the GluA1 subunit of AMPA receptors. We also found that the maintenance of basal levels of CaMKII autophosphorylation requires low-voltage gated T-type calcium channels, but not LTCCs or R-type calcium channels. Our findings indicate that CaMKII activity is dynamically regulated by multiple calcium channels in the striatum thus coupling calcium entry to key downstream substrates.

  11. Design and implementation of a bidirectional current-controlled voltage-regulated DC-DC switched-mode converter

    CSIR Research Space (South Africa)

    Coetzer, A

    2016-01-01

    Full Text Available The design and implementation of a bidirectional current-controlled voltage-regulated DC-DC converter is presented. The converter is required to connect a battery of electrochemical cells (the battery) to an asynchronous motor-drive unit via a...

  12. Amigo Adhesion Protein Regulates Development of Neural Circuits in Zebrafish Brain*

    Science.gov (United States)

    Zhao, Xiang; Kuja-Panula, Juha; Sundvik, Maria; Chen, Yu-Chia; Aho, Vilma; Peltola, Marjaana A.; Porkka-Heiskanen, Tarja; Panula, Pertti; Rauvala, Heikki

    2014-01-01

    The Amigo protein family consists of three transmembrane proteins characterized by six leucine-rich repeat domains and one immunoglobulin-like domain in their extracellular moieties. Previous in vitro studies have suggested a role as homophilic adhesion molecules in brain neurons, but the in vivo functions remain unknown. Here we have cloned all three zebrafish amigos and show that amigo1 is the predominant family member expressed during nervous system development in zebrafish. Knockdown of amigo1 expression using morpholino oligonucleotides impairs the formation of fasciculated tracts in early fiber scaffolds of brain. A similar defect in fiber tract development is caused by mRNA-mediated expression of the Amigo1 ectodomain that inhibits adhesion mediated by the full-length protein. Analysis of differentiated neural circuits reveals defects in the catecholaminergic system. At the behavioral level, the disturbed formation of neural circuitry is reflected in enhanced locomotor activity and in the inability of the larvae to perform normal escape responses. We suggest that Amigo1 is essential for the development of neural circuits of zebrafish, where its mechanism involves homophilic interactions within the developing fiber tracts and regulation of the Kv2.1 potassium channel to form functional neural circuitry that controls locomotion. PMID:24904058

  13. Regulation of cough and action potentials by voltage-gated Na channels.

    Science.gov (United States)

    Carr, Michael J

    2013-10-01

    The classical role ascribed to voltage-gated Na channels is the conduction of action potentials. Some excitable tissues such as cardiac muscle and skeletal muscle predominantly express a single voltage-gated Na channels isoform. Of the nine voltage-gated Na channels, seven are expressed in neurons, of these Nav 1.7, 1.8 and 1.9 are expressed in sensory neurons including vagal sensory neurons that innervate the airways and initiate cough. Nav 1.7 and Nav 1.9 are of particular interest as they represent two extremes in the functional diversity of voltage-gated Na channels. Voltage-gated Na channel isoforms expressed in airway sensory neurons produce multiple distinct Na currents that underlie distinct aspects of sensory neuron function. The interaction between voltage-gated Na currents underlies the characteristic ability of airway sensory nerves to encode encounters with irritant stimuli into action potential discharge and evoke the cough reflex.

  14. Review on Out-Of-Phase Making and Breaking Test Method of High-Voltage Circuit Breaker%高压断路器失步开合试验方法的评述

    Institute of Scientific and Technical Information of China (English)

    吴盛刚; 张建新; 赵建沛; 王鹏飞; 周跃刚

    2013-01-01

    Description was made to the multiple test circuits and the test conditions of high-voltage circuit breakers in carrying out out-of-phase making and breaking test and comparison was made to their advantages and disadvantages. According to the actual test conditions in test station, this paper selected transformer double-circuit which is convenient to carry out and parallel voltage injec-tion circuit and calculated parameters of 126 kV level test loop. Simulation was carried out for the relevant transient recovery voltage waveforms. The result is in conformity with the expected requirements, so it can be implemented.%阐述了高压断路器进行失步开合试验的多种试验线路及其试验条件,并比较了各自的优缺点。根据试验站的具体设备条件,选取了便于实施的变压器双联电路和并联电压引入回路,并计算了126 kV级试验回路的参数,对相应的瞬态恢复电压TRV波形进行了仿真,其结果符合预期要求,故可以实施。

  15. 750 kV断路器现场交流耐压试验系统研究与应用%Site AC Voltage Withstand Test System Study and Application of 750 kV Circuit Breakers

    Institute of Scientific and Technical Information of China (English)

    温定筠; 乔立凤; 江峰; 王成生; 孙亚明; 吕景顺

    2013-01-01

      介绍了750 kV断路器现场交流耐压试验的标准和时序,分析了基于串联谐振原理的试验方法及试验系统中各设备的具体参数。在此基础上配置出成套的750 kV断路器现场交流耐压试验系统,通过实例成功完成了750 kV断路器主回路及断口的交流耐压试验。%  Introduction was made to the standard and time sequence of site AC voltage withstand test of 750 kV circuit breakers. Analysis was made to the test methods based on serial resonance principle and actual parameters of different equipment in test system. On the basis of this, the site AC voltage withstand test system of a set of 750 kV circuit breakers was disposed. The actual example shows that the AC voltage withstand test for the main circuit and breaking outlet of 750 kV circuit breakers could be completed successfully.

  16. Improve the open-circuit voltage of ZnO solar cells with inserting ZnS layers by two ways

    Science.gov (United States)

    Sun, Yunfei; Yang, Jinghai; Yang, Lili; Cao, Jian; Gao, Ming; Zhang, Zhiqiang; Wang, Zhe; Song, Hang

    2013-04-01

    ZnS NPs layers were deposited on ZnO NRs by two different ways. One is spin coating; the other is successive ionic layer adsorption and reaction (SILAR) method. The ZnO NRs/ZnS NPs composites were verified by X-ray diffraction, X-ray photoelectron spectroscopy, and UV-visible spectrophotometer; their morphologies and thicknesses were examined by scanning electron microscopic and transmission electron microscopic images. The CdS quantum dot sensitized solar cells (QDSSCs) were constructed using ZnO NRs/ZnS NPs composites as photoanode and their photovoltaic characteristic was studied by J-V curves. The results indicated that the way of SILAR is more beneficial for retarding the back transfer of electrons to CdS and electrolyte than spin coating method. The open-circuit voltage increased to 0.59 V by introducing a ZnS layer through SILAR method. When ZnS NPs layer was deposited for 10 times on ZnO NRs, the conversion efficiency of QDSSC shows ˜3.3 folds increments of as-synthesized ZnO solar cell.

  17. A study on the dependency of the open-circuit voltage on temperature and actual aging state of lithium-ion batteries

    Science.gov (United States)

    Farmann, Alexander; Sauer, Dirk Uwe

    2017-04-01

    The knowledge of nonlinear monotonic correlation between State-of-Charge (SoC) and open-circuit voltage (OCV) is necessary for an accurate battery state estimation in battery management systems. Among the main factors influencing the OCV behavior of lithium-ion batteries (LIBs) are aging, temperature and previous history of the battery. In order to develop an accurate OCV-based SoC estimator, it is necessary that the OCV behavior of the LIBs is sufficiently investigated and understood. In this study, the impact of the mentioned factors on OCV of LIBs at different aging states using various active materials (C/NMC, C/LFP, LTO/NMC) is investigated over a wide temperature range (from -20 °C to +45 °C) comprehensively. It is shown that temperature and aging of the battery influence the battery's relaxation behavior significantly where a linear dependence between the required relaxation time and the temperature can be assumed. Moreover, the required relaxation time increases with decreasing SoC and temperature. Furthermore, we state that for individual LIB, the OCV and the OCV hysteresis change over the battery lifetime. Based on the obtained results a simplified OCV model considering temperature correction term and aging of the battery is proposed.

  18. Fine Tuning of Open-Circuit Voltage by Chlorination in Thieno[3,4- b ]thiophene–Benzodithiophene Terpolymers toward Enhanced Solar Energy Conversion

    Energy Technology Data Exchange (ETDEWEB)

    Qu, Shiwei; Wang, Huan; Mo, Daize; Chao, Pengjie; Yang, Zhen; Li, Longji; Tian, Leilei; Chen, Wei [Materials; Institute; He, Feng

    2017-06-22

    A new family of thieno[3,4-b]thiophene benzodithiophene terpolymers (PBTClx) have been designed and synthesized, in which the chlorine/fluorine content has been adjusted and optimized. As the content of chlorine is increased in polymers, the twist angle between the donor and acceptor is increased, which leads to a diminishment in the planarity and conjugation. As a result, the UV vis absorption is continuous blue-shifted, and the band gap increases from 1.57 to 2.04 eV when the chlorinated moieties increased from 0 to 100%. The highest occupied molecular orbital (HOMO) levels of those polymers are decreased by increasing the content of chlorinated moiety, which opens a window to constantly modify the V-oc values and eventually meets a balance point for optimized solar energy conversion. The highest power conversion efficiency of 8.31% is obtained by using PBTCl25 as the donor and PC71BM as the acceptor in polymer solar cells (PSCs), in which the Voc increased from 0.79 to 0.82 V after 25% chlorinated monomer involved in copolymerization. Herein, the chlorine replacement could be a good method to further pump the solar conversion by increasing the open circuit voltage without reducing other factors of the polymer solar cells.

  19. Crucial Role of the Electron Transport Layer and UV Light on the Open-Circuit Voltage Loss in Inverted Organic Solar Cells.

    Science.gov (United States)

    Tournebize, Aurélien; Mattana, Giorgio; Gorisse, Thérèse; Bousquet, Antoine; Wantz, Guillaume; Hirsch, Lionel; Chambon, Sylvain

    2017-10-04

    Understanding the degradation mechanisms in organic photovoltaics is crucial in order to develop stable organic semiconductors and robust device architectures. The rapid loss of efficiency, referred to as burn-in, is a major issue to be addressed. This study reports on the influence of the electron transport layer (ETLs) and UV light on the drop of open-circuit voltage (Voc) for P3HT:PC60BM-based devices. The results show that Voc loss is induced by the UV and, more importantly, that the ETL can amplify it, with TiOx yielding a stronger drop than ZnO. Using impedance spectroscopy (IS) and X-ray photoelectron spectroscopy (XPS), different degradation mechanisms were identified according to whether the ETL is TiOx or ZnO. For TiOx-based devices, the formation of an interface dipole was identified, resulting in a loss of the flat-band potential (Vfb) and, thus, of the Voc. For ZnO-based devices, chemical modifications of the metal oxide and active layer at the interface were detected, resulting in a doping of the active layer which impacts the Voc. This study highlights the role of the architecture and, more specifically, of the ETL in the severity of burn-in and degradation pathways.

  20. Finding the lost open-circuit voltage in polymer solar cells by UV-ozone treatment of the nickel acetate anode buffer layer.

    Science.gov (United States)

    Wang, Fuzhi; Sun, Gang; Li, Cong; Liu, Jiyan; Hu, Siqian; Zheng, Hua; Tan, Zhan'ao; Li, Yongfang

    2014-06-25

    Efficient polymer solar cells (PSCs) with enhanced open-circuit voltage (Voc) are fabricated by introducing solution-processed and UV-ozone (UVO)-treated nickel acetate (O-NiAc) as an anode buffer layer. According to X-ray photoelectron spectroscopy data, NiAc partially decomposed to NiOOH during the UVO treatment. NiOOH is a dipole species, which leads to an increase in the work function (as confirmed by ultraviolet photoemission spectroscopy), thus benefitting the formation of ohmic contact between the anode and photoactive layer and leading to increased Voc. In addition, the UVO treatment improves the wettability between the substrate and solvent of the active layer, which facilitates the formation of an upper photoactive layer with better morphology. Further, the O-NiAc layer can decrease the series resistance (Rs) and increase the parallel resistance (Rp) of the devices, inducing enhanced Voc in comparison with the as-prepared NiAc-buffered control devices without UVO treatment. For PSCs based on the P3HT:PCBM system, Voc increases from 0.50 to 0.60 V after the NiAc buffer layer undergoes UVO treatment. Similarly, in the P3HT:ICBA system, the Voc value of the device with a UVO-treated NiAc buffer layer increases from 0.78 to 0.88 V, showing an enhanced power conversion efficiency of 6.64%.