WorldWideScience

Sample records for voltage pulses applied

  1. High voltage pulse generator

    Science.gov (United States)

    Fasching, George E.

    1977-03-08

    An improved high-voltage pulse generator has been provided which is especially useful in ultrasonic testing of rock core samples. An N number of capacitors are charged in parallel to V volts and at the proper instance are coupled in series to produce a high-voltage pulse of N times V volts. Rapid switching of the capacitors from the paralleled charging configuration to the series discharging configuration is accomplished by using silicon-controlled rectifiers which are chain self-triggered following the initial triggering of a first one of the rectifiers connected between the first and second of the plurality of charging capacitors. A timing and triggering circuit is provided to properly synchronize triggering pulses to the first SCR at a time when the charging voltage is not being applied to the parallel-connected charging capacitors. Alternate circuits are provided for controlling the application of the charging voltage from a charging circuit to be applied to the parallel capacitors which provides a selection of at least two different intervals in which the charging voltage is turned "off" to allow the SCR's connecting the capacitors in series to turn "off" before recharging begins. The high-voltage pulse-generating circuit including the N capacitors and corresponding SCR's which connect the capacitors in series when triggered "on" further includes diodes and series-connected inductors between the parallel-connected charging capacitors which allow sufficiently fast charging of the capacitors for a high pulse repetition rate and yet allow considerable control of the decay time of the high-voltage pulses from the pulse-generating circuit.

  2. Simulation of subnanosecond streamers in atmospheric-pressure air: Effects of polarity of applied voltage pulse

    Science.gov (United States)

    Babaeva, N. Yu.; Naidis, G. V.

    2016-08-01

    Results of simulation of subnanosecond streamer propagation in corona gap configuration, obtained in the framework of 2D fluid model, are presented. Effects related with the polarity of a voltage pulse applied to the stressed electrode are discussed. It is argued that these effects (dependence of the discharge current and propagation velocity on the polarity of applied voltage) observed in experiments can be attributed to the difference in initial (preceding the streamer formation) distributions of charged species inside the gap. This difference can be caused by preionization (at negative polarity) of the gas inside the discharge gap by runaway electrons. Calculated streamers have large widths (up to 1 cm) and move with velocities in the range of 109-1010 cm s-1, similar to experimental data.

  3. Fast switching thyristor applied in nanosecond-pulse high-voltage generator with closed transformer core.

    Science.gov (United States)

    Li, Lee; Bao, Chaobing; Feng, Xibo; Liu, Yunlong; Fochan, Lin

    2013-02-01

    For a compact and reliable nanosecond-pulse high-voltage generator (NPHVG), the specification parameter selection and potential usage of fast controllable state-solid switches have an important bearing on the optimal design. The NPHVG with closed transformer core and fast switching thyristor (FST) was studied in this paper. According to the analysis of T-type circuit, the expressions for the voltages and currents of the primary and secondary windings on the transformer core of NPHVG were deduced, and the theoretical maximum analysis was performed. For NPHVG, the rise-rate of turn-on current (di/dt) across a FST may exceed its transient rating. Both mean and maximum values of di/dt were determined by the leakage inductances of the transformer, and the difference is 1.57 times. The optimum winding ratio is helpful to getting higher voltage output with lower specification FST, especially when the primary and secondary capacitances have been established. The oscillation period analysis can be effectively used to estimate the equivalent leakage inductance. When the core saturation effect was considered, the maximum di/dt estimated from the oscillating period of the primary current is more accurate than one from the oscillating period of the secondary voltage. Although increasing the leakage inductance of NPHVG can decrease di/dt across FST, it may reduce the output peak voltage of the NPHVG.

  4. Plasma response to transient high voltage pulses

    Indian Academy of Sciences (India)

    S Kar; S Mukherjee

    2013-07-01

    This review reports on plasma response to transient high voltage pulses in a low pressure unmagnetized plasma. Mainly, the experiments are reviewed, when a disc electrode (metallic and dielectric) is biased pulsed negative or positive. The main aim is to review the electron loss in plasmas and particle balance during the negative pulse electrode biasing, when the applied pulse width is less than the ion plasma period. Though the applied pulse width is less than the ion plasma period, ion rarefaction waves are excited. The solitary electron holes are reviewed for positive pulsed bias to the electrode. Also the excitation of waves (solitary electron and ion holes) is reviewed for a metallic electrode covered by a dielectric material. The wave excitation during and after the pulse withdrawal, excitation and propagation characteristics of various electrostatic plasma waves are reviewed here.

  5. High Voltage Pulse Testing Survey.

    Science.gov (United States)

    1985-10-01

    Cryogenic 23 E. Liquids 26 F. Solids 28 1. Polyethylene 28 2. Cross-Linked Polyethylene ( XLPE ) 29 3. Polyimide and Polyvenylchloride (PVC) 31 VI Benefits 35 A...Strength of XLPE Cables 29 vii * 4" I PROGRAM OBJECTIVES The Pulse Test Survey summarizes government, industry, and technical reports on high voltage pulse...system of silicone oil on a XLPE (cross-linked polyethylene) spacer tends to lower the impulse breakdown by approximately 10 percent. The negative impulse

  6. Experimental validation of a high voltage pulse measurement method.

    Energy Technology Data Exchange (ETDEWEB)

    Cular, Stefan; Patel, Nishant Bhupendra; Branch, Darren W.

    2013-09-01

    This report describes X-cut lithium niobates (LiNbO3) utilization for voltage sensing by monitoring the acoustic wave propagation changes through LiNbO3 resulting from applied voltage. Direct current (DC), alternating current (AC) and pulsed voltage signals were applied to the crystal. Voltage induced shift in acoustic wave propagation time scaled quadratically for DC and AC voltages and linearly for pulsed voltages. The measured values ranged from 10 - 273 ps and 189 ps 2 ns for DC and non-DC voltages, respectively. Data suggests LiNbO3 has a frequency sensitive response to voltage. If voltage source error is eliminated through physical modeling from the uncertainty budget, the sensors U95 estimated combined uncertainty could decrease to ~0.025% for DC, AC, and pulsed voltage measurements.

  7. High voltage pulse generator. [Patent application

    Science.gov (United States)

    Fasching, G.E.

    1975-06-12

    An improved high-voltage pulse generator is described which is especially useful in ultrasonic testing of rock core samples. An N number of capacitors are charged in parallel to V volts and at the proper instance are coupled in series to produce a high-voltage pulse of N times V volts. Rapid switching of the capacitors from the paralleled charging configuration to the series discharging configuration is accomplished by using silicon-controlled rectifiers which are chain self-triggered following the initial triggering of the first rectifier connected between the first and second capacitors. A timing and triggering circuit is provided to properly synchronize triggering pulses to the first SCR at a time when the charging voltage is not being applied to the parallel-connected charging capacitors. The output voltage can be readily increased by adding additional charging networks. The circuit allows the peak level of the output to be easily varied over a wide range by using a variable autotransformer in the charging circuit.

  8. Investigation of pulsed voltage limiters characteristics

    Directory of Open Access Journals (Sweden)

    Karimov A. V.

    2012-06-01

    Full Text Available A new method for measuring the voltage limit is offered. It has been designed to measure high-power pulsed current of voltage limiters. The error of this method is half as much as the error of the known method of direct measurement. The investigation of dependence of power capability of single-crystal and double-crystal voltage limiters and of the pulsed operation time on pulse duration.

  9. Generator of ultrashort megavolt voltage pulses

    CERN Document Server

    Zheltov, K A; Shalimanov, V F

    2002-01-01

    Paper describes approx 3 ns duration and > 1 MW amplitude voltage pulse generator under high-ohmic (approx 450 Ohm) load. Generator comprises pulse transformer with magnetized core, as well as, resonance tuned circuit of high-voltage solenoid and accumulating spaces of a shaping line containing, moreover, spark gap to switch charge in transmitting line. Paper contains the results of voltage measuring in generator basic units

  10. Experimental investigation of SDBD plasma actuator driven by AC high voltage with a superimposed positive pulse bias voltage

    Science.gov (United States)

    Qi, Xiao-Hua; Yan, Hui-Jie; Yang, Liang; Hua, Yue; Ren, Chun-Sheng

    2017-08-01

    In this work, a driven voltage consisting of AC high voltage with a superimposed positive pulse bias voltage ("AC+ Positive pulse bias" voltage) is adopted to study the performance of a surface dielectric barrier discharge plasma actuator under atmospheric conditions. To compare the performance of the actuator driven by single-AC voltage and "AC+ Positive pulse bias" voltage, the actuator-induced thrust force and power consumption are measured as a function of the applied AC voltage, and the measured results indicate that the thrust force can be promoted significantly after superimposing the positive pulse bias voltage. The physical mechanism behind the thrust force changes is analyzed by measuring the optical properties, electrical characteristics, and surface potential distribution. Experimental results indicate that the glow-like discharge in the AC voltage half-cycle, next to the cycle where a bias voltage pulse has been applied, is enhanced after applying the positive pulse bias voltage, and this perhaps is the main reason for the thrust force increase. Moreover, surface potential measurement results reveal that the spatial electric field formed by the surface charge accumulation after positive pulse discharge can significantly affect the applied external electric field, and this perhaps can be responsible for the experimental phenomenon that the decrease of thrust force is delayed by pulse bias voltage action after the filament discharge occurs in the glow-like discharge region. The schlieren images further verify that the actuator-induced airflow velocity increases with the positive pulse voltage.

  11. Multiple High Voltage Pulse Stressing of Polymer Thick Film Resistors

    Directory of Open Access Journals (Sweden)

    Busi Rambabu

    2014-01-01

    Full Text Available The purpose of this paper is to study high voltage interactions in polymer thick film resistors, namely, polyvinyl chloride- (PVC- graphite thick film resistors, and their applications in universal trimming of these resistors. High voltages in the form of impulses for various pulse durations and with different amplitudes have been applied to polymer thick film resistors and we observed the variation of resistance of these resistors with high voltages. It has been found that the resistance of polymer thick film resistors decreases in the case of higher resistivity materials and the resistance of polymer thick film resistor increases in the case of lower resistivity materials when high voltage impulses are applied to them. It has been also found that multiple high voltage pulse (MHVP stressing can be used to trim the polymer thick film resistors either upwards or downwards.

  12. Treatment of emulsified oils by electrocoagulation: pulsed voltage applications.

    Science.gov (United States)

    Genc, Ayten; Bakirci, Busra

    2015-01-01

    The effect of pulsed voltage application on energy consumption during electrocoagulation was investigated. Three voltage profiles having the same arithmetic average with respect to time were applied to the electrodes. The specific energy consumption for these profiles were evaluated and analyzed together with oil removal efficiencies. The effects of applied voltages, electrode materials, electrode configurations, and pH on oil removal efficiency were determined. Electrocoagulation experiments were performed by using synthetic and real wastewater samples. The pulsed voltages saved energy during the electrocoagulation process. In continuous operation, energy saving was as high as 48%. Aluminum electrodes used for the treatment of emulsified oils resulted in higher oil removal efficiencies in comparison with stainless steel and iron electrodes. When the electrodes gap was less than 1 cm, higher oil removal efficiencies were obtained. The highest oil removal efficiencies were 95% and 35% for the batch and continuous operating modes, respectively.

  13. Development of high-voltage pulse-slicer unit with variable pulse duration for pulse radiolysis system

    Science.gov (United States)

    Upadhyay, J.; Sharma, M. L.; Navathe, C. P.; Toley, M. A.; Shinde, S. J.; Nadkarni, S. A.; Sarkar, S. K.

    2012-02-01

    A high-voltage pulse-slicer unit with variable pulse duration has been developed and integrated with a 7 MeV linear electron accelerator (LINAC) for pulse radiolysis investigation. The pulse-slicer unit provides switching voltage from 1 kV to 10 kV with rise time better than 5 ns. Two MOSFET based 10 kV switches were configured in differential mode to get variable duration pulses. The high-voltage pulse has been applied to the deflecting plates of the LINAC for slicing of electron beam of 2 μs duration. The duration of the electron beam has been varied from 30 ns to 2 μs with the optimized pulse amplitude of 7 kV to get corresponding radiation doses from 6 Gy to 167 Gy.

  14. High voltage magnetic pulse generation using capacitor discharge technique

    Directory of Open Access Journals (Sweden)

    M. Rezal

    2014-12-01

    Full Text Available A high voltage magnetic pulse is designed by applying an electrical pulse to the coil. Capacitor banks are developed to generate the pulse current. Switching circuit consisting of Double Pole Double Throw (DPDT switches, thyristor, and triggering circuit is developed and tested. The coil current is measured using a Hall-effect current sensor. The magnetic pulse generated is measured and tabulated in a graph. Simulation using Finite Element Method Magnetics (FEMM is done to compare the results obtained between experiment and simulation. Results show that increasing the capacitance of the capacitor bank will increase the output voltage. This technology can be applied to areas such as medical equipment, measurement instrument, and military equipment.

  15. DIFFUSE DBD IN ATMOSPHERIC AIR AT DIFFERENT APPLIED PULSE WIDTHS

    Directory of Open Access Journals (Sweden)

    Ekaterina Alexandrovna Shershunova

    2015-02-01

    Full Text Available The paper deals with the realization and the diagnostics of the volume diffuse dielectric barrier discharge in 1-mm air gap when applying high voltage rectangular pulses to the electrodes. The effect of the applied pulse width on the discharge dissipated energy was studied in detail. It was found experimentally, the energy stayed nearly constant with the pulse elongation from 600 ns to 1 ms.

  16. A 70 kV solid-state high voltage pulse generator based on saturable pulse transformer.

    Science.gov (United States)

    Fan, Xuliang; Liu, Jinliang

    2014-02-01

    High voltage pulse generators are widely applied in many fields. In recent years, solid-state and operating at repetitive mode are the most important developing trends of high voltage pulse generators. A solid-state high voltage pulse generator based on saturable pulse transformer is proposed in this paper. The proposed generator is consisted of three parts. They are charging system, triggering system, and the major loop. Saturable pulse transformer is the key component of the whole generator, which acts as a step-up transformer and main switch during working process of this generator. The circuit and working principles of the proposed pulse generator are introduced first in this paper, and the saturable pulse transformer used in this generator is introduced in detail. Circuit of the major loop is simulated to verify the design of the system. Demonstration experiments are carried out, and the results show that when the primary energy storage capacitor is charged to a high voltage, such as 2.5 kV, a voltage with amplitude of 86 kV can be achieved on the secondary winding. The magnetic core of saturable pulse transformer is saturated deeply and the saturable inductance of the secondary windings is very small. The switch function of the saturable pulse transformer can be realized ideally. Therefore, a 71 kV output voltage pulse is formed on the load. Moreover, the magnetic core of the saturable pulse transformer can be reset automatically.

  17. High-voltage, short-risetime pulse generator based on a ferrite pulse sharpener

    Energy Technology Data Exchange (ETDEWEB)

    Seddon, N.; Thornton, E.

    1988-11-01

    A high-voltage, short-risetime pulse generator is described. The generator consists of a Marx bank, which produces an initial high-voltage pulse, and a ferrite pulse sharpener that reduces the risetime of the pulse. The generator delivers 70-kV, 350-ps risetime pulses into a 50-..cap omega.. load.

  18. Environmental and biotechnological applications of high-voltage pulsed discharges in water

    Energy Technology Data Exchange (ETDEWEB)

    Sato, Masayuki [Department of Chemical and Environmental Engineering, Gunma University 1-5-1 Tenjin, Kiryu, Gunma 376-8515 (Japan)], E-mail: mxsato@cee.gunma-u.ac.jp

    2008-05-01

    A high-voltage pulse has wide application in fields such as chemistry, physics and biology and their combinations. The high-voltage pulse forms two kinds of physical processes in water, namely (a) a pulsed electric field (PEF) in the parallel electrode configuration and (b) plasma generation by a pulsed discharge in the water phase with a concentrated electric field. The PEF can be used for inactivation of bacteria in liquid foods as a non-thermal process, and the underwater plasma is applicable not only for the decomposition of organic materials in water but also for biological treatment of wastewater. These discharge states are controlled mainly by the applied pulse voltage and the electrode shape. Some examples of environmental and biotechnological applications of a high-voltage pulse are reviewed.

  19. High-voltage air-core pulse transformers

    Energy Technology Data Exchange (ETDEWEB)

    Rohwein, G. J.

    1981-01-01

    General types of air core pulse transformers designed for high voltage pulse generation and energy transfer applications are discussed with special emphasis on pulse charging systems which operate up to the multi-megavolt range. The design, operation, dielectric materials, and performance are described. It is concluded that high voltage air core pulse transformers are best suited to applications outside the normal ranges of conventional magnetic core transformers. In general these include charge transfer at high power levels and fast pulse generation with comparatively low energy. When properly designed and constructed, they are capable of delivering high energy transfer efficiency and have demonstrated superior high voltage endurance. The principal disadvantage of high voltage air core transformers is that they are not generally available from commercial sources. Consequently, the potential user must become thoroughly familiar with all aspects of design, fabrication and system application before he can produce a high performance transformer system. (LCL)

  20. Understanding and Improving High Voltage Vacuum Insulators for Microsecond Pulses

    Energy Technology Data Exchange (ETDEWEB)

    Javedani, J B; Goerz, D A; Houck, T L; Lauer, E J; Speer, R D; Tully, L K; Vogtlin, G E; White, A D

    2007-03-05

    High voltage insulation is one of the main areas of pulsed power research and development, and dielectric breakdown is usually the limiting factor in attaining the highest possible performance in pulsed power devices. For many applications the delivery of pulsed power into a vacuum region is the most critical aspect of operation. The surface of an insulator exposed to vacuum can fail electrically at an applied field more than an order or magnitude below the bulk dielectric strength of the insulator. This mode of breakdown, called surface flashover, imposes serious limitations on the power flow into a vacuum region. This is especially troublesome for applications where high voltage conditioning of the insulator and electrodes is not practical and for applications where relatively long pulses, on the order of several microseconds, are required. The goal of this project is to establish a sound fundamental understanding of the mechanisms that lead to surface flashover, and then evaluate the most promising techniques to improve vacuum insulators and enable high voltage operation at stress levels near the intrinsic bulk breakdown limits of the material. The approach we proposed and followed was to develop this understanding through a combination of theoretical and computation methods coupled with experiments to validate and quantify expected behaviors. In this report we summarize our modeling and simulation efforts, theoretical studies, and experimental investigations. The computational work began by exploring the limits of commercially available codes and demonstrating methods to examine field enhancements and defect mechanisms at microscopic levels. Plasma simulations with particle codes used in conjunction with circuit models of the experimental apparatus enabled comparisons with experimental measurements. The large scale plasma (LSP) particle-in-cell (PIC) code was run on multiprocessor platforms and used to simulate expanding plasma conditions in vacuum gap regions

  1. Finite Element Based Optimal Design Approach for High Voltage Pulse Transformers

    CERN Document Server

    Aguglia, D; Viarouge, P; Cros, J

    2014-01-01

    This paper presents an optimal design methodology of monolithic high voltage pulse transformers based on the direct 2D FEA identification of the electrical equivalent circuit parameters. This method is applied to the preliminary optimal design of the monolithic high voltage pulse transformer for the future CLIC modulators under study at CERN. The feasibility of such a transformer with tight specifications is demonstrated. The predicted performances obtained with the direct 2D FEA optimization process is validated by 3D FEA simulation.

  2. Characteristics for electrochemical machining with nanoscale voltage pulses.

    Science.gov (United States)

    Lee, E S; Back, S Y; Lee, J T

    2009-06-01

    Electrochemical machining has traditionally been used in highly specialized fields, such as those of the aerospace and defense industries. It is now increasingly being applied in other industries, where parts with difficult-to-cut material, complex geometry and tribology, and devices of nanoscale and microscale are required. Electric characteristic plays a principal function role in and chemical characteristic plays an assistant function role in electrochemical machining. Therefore, essential parameters in electrochemical machining can be described current density, machining time, inter-electrode gap size, electrolyte, electrode shape etc. Electrochemical machining provides an economical and effective method for machining high strength, high tension and heat-resistant materials into complex shapes such as turbine blades of titanium and aluminum alloys. The application of nanoscale voltage pulses between a tool electrode and a workpiece in an electrochemical environment allows the three-dimensional machining of conducting materials with sub-micrometer precision. In this study, micro probe are developed by electrochemical etching and micro holes are manufactured using these micro probe as tool electrodes. Micro holes and microgroove can be accurately achieved by using nanoscale voltages pulses.

  3. The Dynamic Fracture Process in Rocks Under High-Voltage Pulse Fragmentation

    Science.gov (United States)

    Cho, Sang Ho; Cheong, Sang Sun; Yokota, Mitsuhiro; Kaneko, Katsuhiko

    2016-10-01

    High-voltage pulse technology has been applied to rock excavation, liberation of microfossils, drilling of rocks, oil and water stimulation, cleaning castings, and recycling products like concrete and electrical appliances. In the field of rock mechanics, research interest has focused on the use of high-voltage pulse technology for drilling and cutting rocks over the past several decades. In the use of high-voltage pulse technology for drilling and cutting rocks, it is important to understand the fragmentation mechanism in rocks subjected to high-voltage discharge pulses to improve the effectiveness of drilling and cutting technologies. The process of drilling rocks using high-voltage discharge is employed because it generates electrical breakdown inside the rocks between the anode and cathode. In this study, seven rock types and a cement paste were electrically fractured using high-voltage pulse discharge to investigate their dielectric breakdown properties. The dielectric breakdown strengths of the samples were compared with their physical and mechanical properties. The samples with dielectric fractured were scanned using a high-resolution X-ray computed tomography system to observe the fracture formation associated with mineral constituents. The fracture patterns of the rock samples were analyzed using numerical simulation for high-voltage pulse-induced fragmentation that adopts the surface traction and internal body force conditions.

  4. High voltage pulsed cable design: a practical example

    Energy Technology Data Exchange (ETDEWEB)

    Kewish, R.W. Jr.; Boicourt, G.P.

    1979-01-01

    The design of optimum high voltage pulse cable is difficult because very little emperical data are available on performance in pulsed applications. This paper follows the design and testing of one high voltage pulse cable, 40/100 trigger cable. The design was based on an unproven theory and the impressive outcome lends support to the theory. The theory is outlined and it is shown that there exists an inductance which gives a cable of minimum size for a given maximum stress. Test results on cable manufactured according to the design are presented and compared with the test results on the cable that 40/100 replaces.

  5. Breakdown voltage of discrete capacitors under single-pulse conditions

    Science.gov (United States)

    Domingos, H.; Scaturro, J.; Hayes, L.

    1981-01-01

    For electrostatic capacitors the breakdown voltage is inherently related to the properties of the dielectric, with the important parameters being the dielectric field strength which is related to the dielectric constant and the dielectric thickness. These are not necessarily related to the capacitance value and the rated voltage, but generally the larger values of capacitance have lower breakdown voltages. Foil and wet slug electrolytics can withstand conduction currents pulses without apparent damage (in either direction for foil types). For solid tantalums, damage occurs whenever the capacitor charges to the forming voltage.

  6. High-voltage pulsed generator for dynamic fragmentation of rocks.

    Science.gov (United States)

    Kovalchuk, B M; Kharlov, A V; Vizir, V A; Kumpyak, V V; Zorin, V B; Kiselev, V N

    2010-10-01

    A portable high-voltage (HV) pulsed generator has been designed for rock fragmentation experiments. The generator can be used also for other technological applications. The installation consists of low voltage block, HV block, coaxial transmission line, fragmentation chamber, and control system block. Low voltage block of the generator, consisting of a primary capacitor bank (300 μF) and a thyristor switch, stores pulse energy and transfers it to the HV block. The primary capacitor bank stores energy of 600 J at the maximum charging voltage of 2 kV. HV block includes HV pulsed step up transformer, HV capacitive storage, and two electrode gas switch. The following technical parameters of the generator were achieved: output voltage up to 300 kV, voltage rise time of ∼50 ns, current amplitude of ∼6 kA with the 40 Ω active load, and ∼20 kA in a rock fragmentation regime (with discharge in a rock-water mixture). Typical operation regime is a burst of 1000 pulses with a frequency of 10 Hz. The operation process can be controlled within a wide range of parameters. The entire installation (generator, transmission line, treatment chamber, and measuring probes) is designed like a continuous Faraday's cage (complete shielding) to exclude external electromagnetic perturbations.

  7. A PC-controlled voltage pulse generator for electroanalytical applications

    Science.gov (United States)

    Heredia-López, Francisco J.; Góngora-Alfaro, José L.; Alvarez-Cervera, Fernando J.; Bata-García, José Luis

    1997-04-01

    We present the design of a voltage pulse generator controlled by an IBM or compatible AT Personal Computer (PC) capable of synthesizing some of the voltage pulse wave forms commonly used in electrochemical studies. The included signals are: differential pulse voltametry, differential normal pulse voltametry, and differential pulse amperometry. Additionally, a triangular wave form and a constant-voltage signal, used in the pretreatment of carbon fiber microelectrodes for neurochemical analysis, are also available. Operating the generator imposes a minimum of restrictions on the specification of the duration, amplitude, and type of wave shapes. Low-cost PC-based design allows for compatibility, portability, and versatility. The operating ranges of the wave form parameters for the three voltametric signals are: initial voltage, -0.9-+0.9 V; step amplitude, 0.1-900 mV; period, 6 ms-60 s; measuring pulse amplitude, 0.1-900 mV; measuring pulse duration, 2 ms-20 s; prepulse duration, 2 ms-20 s. In the electrode pretreatment mode, the operating ranges are: amplitude, 0-±5 V; duration, unlimited; frequency, 15-240 Hz. The generator uses its own time base for the generation of all signals, thereby rendering it independent of processor clock speed or power-line frequency. The results of the experimental evaluation indicate that the system is accurate within ±10% of the expected values, taking into account the errors associated with the signal synthesis and the digitizing process. The maximum achievable scan rate is 500 V/s, and the highest frequency for the triangular wave form is 240 Hz. Therefore, the pulse generator could be used for fast cyclic voltametry (FCV). FCV and other wave forms could be added through software modules, without any hardware changes. We conclude that the PC-based electrochemistry pulse generator represents an economical and flexible alternative for electroanalytical applications.

  8. Forward voltage short-pulse technique for measuring high power laser array junction temperature

    Science.gov (United States)

    Meadows, Byron L. (Inventor); Amzajerdian, Frazin (Inventor); Barnes, Bruce W. (Inventor); Baker, Nathaniel R. (Inventor)

    2012-01-01

    The present invention relates to a method of measuring the temperature of the P-N junction within the light-emitting region of a quasi-continuous-wave or pulsed semiconductor laser diode device. A series of relatively short and low current monitor pulses are applied to the laser diode in the period between the main drive current pulses necessary to cause the semiconductor to lase. At the sufficiently low current level of the monitor pulses, the laser diode device does not lase and behaves similar to an electronic diode. The voltage across the laser diode resulting from each of these low current monitor pulses is measured with a high degree of precision. The junction temperature is then determined from the measured junction voltage using their known linear relationship.

  9. Hybrid Design Optimization of High Voltage Pulse Transformers for Klystron Modulators

    CERN Document Server

    Sylvain, Candolfi; Davide, Aguglia; Jerome, Cros

    2015-01-01

    This paper presents a hybrid optimization methodology for the design of high voltage pulse transformers used in klystron modulators. The optimization process is using simplified 2D FEA design models of the 3D transformer structure. Each intermediate optimal solution is evaluated by 3D FEA and correction coefficients of the 2D FEA models are derived. A new optimization process using 2D FEA models is then performed. The convergence of this hybrid optimal design methodology is obtained with a limited number of time consuming 3D FEA simulations. The method is applied to the optimal design of a monolithic high voltage pulse transformer for the CLIC klystron modulator.

  10. Numeric modeling of synchronous laser pulsing and voltage pulsing field evaporation

    CERN Document Server

    Zhao, L; Houard, J; Blum, I; Delaroche, F; Vurpillot, F

    2016-01-01

    We have recently proposed an atom probe design based on a femtosecond time-resolved pump-probe setup. This setup unlocks the limitation of voltage pulsed mode atom probe thanks to the occurrence of local photoconductive switching effect . In this paper, we have used a numerical model to simulate the field evaporation process triggered by the synchronous two pulses. The model takes into account the local photoconductive effect and the temperature rise caused by the laser application and the voltage pulse distortion due to the RC effect.

  11. A compact, low jitter, nanosecond rise time, high voltage pulse generator with variable amplitude

    Science.gov (United States)

    Mao, Jiubing; Wang, Xin; Tang, Dan; Lv, Huayi; Li, Chengxin; Shao, Yanhua; Qin, Lan

    2012-07-01

    In this paper, a compact, low jitter, nanosecond rise time, command triggered, high peak power, gas-switch pulse generator system is developed for high energy physics experiment. The main components of the system are a high voltage capacitor, the spark gap switch and R = 50 Ω load resistance built into a structure to obtain a fast high power pulse. The pulse drive unit, comprised of a vacuum planar triode and a stack of avalanche transistors, is command triggered by a single or multiple TTL (transistor-transistor logic) level pulses generated by a trigger pulse control unit implemented using the 555 timer circuit. The control unit also accepts user input TTL trigger signal. The vacuum planar triode in the pulse driving unit that close the first stage switches is applied to drive the spark gap reducing jitter. By adjusting the charge voltage of a high voltage capacitor charging power supply, the pulse amplitude varies from 5 kV to 10 kV, with a rise time of gas-switch and available capacitor recovery time.

  12. Electric Double-Layer Capacitors Applying to Voltage Sag Compensator

    Science.gov (United States)

    Nara, Hidetaka

    Recently the electric double-layer capacitor (EDLC) which is rapidly charged and discharged and offers long life, maintenance-free, has been developed as a new energy storage element. Therefore, we developed the uninterruptible power supply as voltage sag compensator utilizing EDLC. This paper describes an abstract of EDLC and applying to voltage sag compensation.

  13. Efficient Parametric Identification Method for High Voltage Pulse Transformers

    CERN Document Server

    Aguglia, D; Viarouge, P; Cros, J

    2014-01-01

    This paper presents a new identification method for a pulse transformer equivalent circuit. It is based on an analytical approximation of the frequency-domain impedance data derived from a no-load test with open-circuited secondary winding and only requires measurements of primary current and voltage without phase data. Compared with time consuming and complex methods based on off-line non-linear identification procedures, this simple method also gives an estimation of the error on the identified parameters. The method is validated on an existing pulse transformer.

  14. High voltage high repetition rate pulse using Marx topology

    Science.gov (United States)

    Hakki, A.; Kashapov, N.

    2015-06-01

    The paper describes Marx topology using MOSFET transistors. Marx circuit with 10 stages has been done, to obtain pulses about 5.5KV amplitude, and the width of the pulses was about 30μsec with a high repetition rate (PPS > 100), Vdc = 535VDC is the input voltage for supplying the Marx circuit. Two Ferrite ring core transformers were used to control the MOSFET transistors of the Marx circuit (the first transformer to control the charging MOSFET transistors, the second transformer to control the discharging MOSFET transistors).

  15. Removal of phenol by activated alumina bed in pulsed high-voltage electric field

    Institute of Scientific and Technical Information of China (English)

    ZHU Li-nan; MA Jun; YANG Shi-dong

    2007-01-01

    A new process for removing the pollutants in aqueous solution-activated alumina bed in pulsed high-voltage electric field was investigated for the removal of phenol under different conditions. The experimental results indicated the increase in removal rate with increasing applied voltage, increasing pH value of the solution, aeration, and adding Fe2+. The removal rate of phenol could reach 72.1 % when air aeration flow rate was 1200 ml/min, and 88.2 % when 0.05 mmol/L Fe2+ was added into the solution under the conditions of applied voltage 25 kV, initial phenol concentration of 5 mg/L, and initial pH value 5.5. The addition of sodium carbonate reduced the phenol removal rate. In the pulsed high-voltage electric field, local discharge occurred at the surface of activated alumina, which promoted phenol degradation in the thin water film. At the same time, the space-time distribution of gas-liquid phases was more uniform and the contact areas of the activated species generated from the discharge and the pollutant molecules were much wider due to the effect of the activated alumina bed. The synthetical effects of the pulsed high-voltage electric field and the activated alumina particles accelerated phenol degradation.

  16. A compact high-voltage pulse generator based on pulse transformer with closed magnetic core.

    Science.gov (United States)

    Zhang, Yu; Liu, Jinliang; Cheng, Xinbing; Bai, Guoqiang; Zhang, Hongbo; Feng, Jiahuai; Liang, Bo

    2010-03-01

    A compact high-voltage nanosecond pulse generator, based on a pulse transformer with a closed magnetic core, is presented in this paper. The pulse generator consists of a miniaturized pulse transformer, a curled parallel strip pulse forming line (PFL), a spark gap, and a matched load. The innovative design is characterized by the compact structure of the transformer and the curled strip PFL. A new structure of transformer windings was designed to keep good insulation and decrease distributed capacitance between turns of windings. A three-copper-strip structure was adopted to avoid asymmetric coupling of the curled strip PFL. When the 31 microF primary capacitor is charged to 2 kV, the pulse transformer can charge the PFL to 165 kV, and the 3.5 ohm matched load can deliver a high-voltage pulse with a duration of 9 ns, amplitude of 84 kV, and rise time of 5.1 ns. When the load is changed to 50 ohms, the output peak voltage of the generator can be 165 kV, the full width at half maximum is 68 ns, and the rise time is 6.5 ns.

  17. ELABORATION OF HIGH-VOLTAGE PULSE INSTALLATIONS AND PROVIDING THEIR OPERATION PROTECTIVE MEASURES

    Directory of Open Access Journals (Sweden)

    А. М. Hashimov

    2016-01-01

    Full Text Available The article presents design engineering methods for the high-voltage pulse installations of technological purpose for disinfection of drinking water, sewage, and edible liquids by high field micro- and nanosecond pulsing exposure. Designing potentialities are considered of the principal elements of the high-voltage part and the discharge circuit of the installations towards assuring the best efficient on-load utilization of the source energy and safe operation of the high-voltage equipment. The study shows that for disinfection of drinking water and sewage it is expedient to apply microsecond pulse actions causing the electrohydraulic effect in aqueous media with associated complex of physical processes (ultraviolet emission, generation of ozone and atomic oxygen, mechanical compression waves, etc. having detrimental effect on life activity of the microorganisms. In case of disinfecting edible liquids it is recommended to use the nanosecond pulses capable of straight permeating the biological cell nucleus, inactivating it. Meanwhile, the nutritive and biological values of the foodstuffs are saved and their organoleptic properties are improved. It is noted that in elaboration process of high-frequency pulse installations special consideration should be given to issues of the operating personnel safety discipline and securing conditions for the entire installation uninterrupted performance. With this objective in view the necessary requirements should be fulfilled on shielding the high- and low-voltage installation parts against high-frequency electromagnetic emissions registered by special differential sensors. Simultaneously, the abatement measures should be applied on the high-voltage equipment operational noise level. The authors offer a technique for noise abatement to admissible levels (lower than 80 dB A by means of coating the inside surface with shielded enclosure of densely-packed abutting sheets of porous electro-acoustic insulating

  18. An atmospheric pressure plasma source driven by a train of monopolar high voltage pulses superimposed to a dc voltage

    OpenAIRE

    Stoican, O.S.

    2011-01-01

    Abstract An atmospheric pressure plasma source supplied by an electrical circuit consisting of two voltage sources in parallel connection is reported. One of them is a low-power self-oscillating flyback converter which produces negative voltage pulses with an amplitude of several kilovolts. The high voltage pulses are necessary to ignite an electrical discharge between the electrodes at atmospheric pressure. An additional dc source delivering several hundreds of volts at a few hund...

  19. Continuous-flow multi-pulse electroporation at low DC voltages by microfluidic flipping of the voltage space topology

    Science.gov (United States)

    Bhattacharjee, N.; Horowitz, L. F.; Folch, A.

    2016-10-01

    Concerns over biosafety, cost, and carrying capacity of viral vectors have accelerated research into physical techniques for gene delivery such as electroporation and mechanoporation. Advances in microfabrication have made it possible to create high electric fields over microscales, resulting in more efficient DNA delivery and higher cell viability. Continuous-flow microfluidic methods are typically more suitable for cellular therapies where a large number of cells need to be transfected under sterile conditions. However, the existing continuous-flow designs used to generate multiple pulses either require expensive peripherals such as high-voltage (>400 V) sources or function generators, or result in reduced cell viability due to the proximity of the cells to the electrodes. In this paper, we report a continuous-flow microfluidic device whose channel geometry reduces instrumentation demands and minimizes cellular toxicity. Our design can generate multiple pulses of high DC electric field strength using significantly lower voltages (15-60 V) than previous designs. The cells flow along a serpentine channel that repeatedly flips the cells between a cathode and an anode at high throughput. The cells must flow through a constriction each time they pass from an anode to a cathode, exposing them to high electric field strength for short durations of time (the "pulse-width"). A conductive biocompatible poly-aniline hydrogel network formed in situ is used to apply the DC voltage without bringing the metal electrodes close to the cells, further sheltering cells from the already low voltage electrodes. The device was used to electroporate multiple cell lines using electric field strengths between 700 and 800 V/cm with transfection efficiencies superior than previous flow-through designs.

  20. Development of ultra-short high voltage pulse technology using magnetic pulse compression

    Energy Technology Data Exchange (ETDEWEB)

    Cha, Byung Heon; Kim, S. G.; Nam, S. M.; Lee, B. C.; Lee, S. M.; Jeong, Y. U.; Cho, S. O.; Jin, J. T.; Choi, H. L

    1998-01-01

    The control circuit for high voltage switches, the saturable inductor for magnetic assist, and the magnetic pulse compression circuit were designed, constructed, and tested. The core materials of saturable inductors in magnetic pulse compression circuit were amorphous metal and ferrite and total compression stages were 3. By the test, in high repetition rate, high pulse compression were certified. As a result of this test, it became possible to increase life-time of thyratrons and to replace thyratrons by solid-state semiconductor switches. (author). 16 refs., 16 tabs.

  1. Pulse voltage determination for electrostatic micro manipulation considering surface conductivity and adhesion of glass particle

    Directory of Open Access Journals (Sweden)

    Ryo Fujiwara

    2015-05-01

    Full Text Available A model with surface conductivity and adhesional force is proposed to investigate the mechanism for electrostatic micro manipulation of a dielectric object using a single probe. The manipulation system consists of three elements: a conductive probe as a manipulator, a conductive plate as a substrate, and a dielectric particle as the target object for manipulation. The particle can be successfully picked up/placed if a rectangular pulse voltage is applied between the probe and the plate. The reliability of the picking up/placing operation is improved by applying a pulse voltage that is determined by a theoretical model considering surface conductivity and adhesion. To verify the theoretical prediction, manipulation experiment is conducted using soda-lime glass particles with radii of 20 μm and 40 μm.

  2. Review of the Dynamics of Coalescence and Demulsification by High-Voltage Pulsed Electric Fields

    OpenAIRE

    Ye Peng; Tao Liu; Haifeng Gong; Xianming Zhang

    2016-01-01

    The coalescence of droplets in oil can be implemented rapidly by high-voltage pulse electric field, which is an effective demulsification dehydration technological method. At present, it is widely believed that the main reason of pulse electric field promoting droplets coalescence is the dipole coalescence and oscillation coalescence in pulse electric field, and the optimal coalescence pulse electric field parameters exist. Around the above content, the dynamics of high-voltage pulse electric...

  3. High Voltage Coaxial Vacuum Gap Breakdown for Pulsed Power Liners

    Science.gov (United States)

    Cordaro, Samuel; Bott-Suzuki, Simon; Caballero Bendixsen, Luis Sebastian

    2015-11-01

    The dynamics of Magnetized Liner Inertial Fusion (MagLIF)1, are presently under detailed study at Sandia National Laboratories. Alongside this, a comprehensive analysis of the influence of the specific liner design geometry in the MagLIF system on liner initiation is underway in the academic community. Recent work at UC San Diego utilizes a high voltage pulsed system (25kV, 150ns) to analyze the vacuum breakdown stage of liner implosion. Such experimental analyses are geared towards determining how the azimuthal symmetry of coaxial gap breakdown affect plasma initiation within the liner. The final aim of the experimental analysis is to assess to what scale symmetry remains important at high (MV) voltages. An analysis of the above will utilize plasma self-emission via optical MCP, current measurements, voltage measurements near the gap, exact location of breakdown via 2D b-dot probe triangulation, as well as measuring the evolution of the B-field along the length of the liner via b-dot array. Results will be discussed along with analytical calculations of breakdown mechanisms

  4. Dynamic Voltage Restorer Based on Space Vector Pulse Width Modulation Technique

    Directory of Open Access Journals (Sweden)

    B.N S P Venkatesh

    2011-07-01

    Full Text Available Power Quality problems encompass a wide range of disturbances such as voltage sags, swells, flicker,harmonics distortion and interruptions. The strategic deployment of custom power devices has been proposed asone of the means to protect sensitive loads from power quality problems such as voltage sags and swells. The Dynamic Voltage Restorer (DVR is a power electronic device that is used to inject 3-phase voltage in series and in synchronism with the distribution feeder voltages in order to compensate voltage sag and similarly itreacts quickly to inject the appropriate voltage component (negative voltage magnitude in order to compensate voltage swell. The principal component of the DVR is a voltage source inverter that generates three phase voltages and provides the voltage support to a sensitive load during voltage sags and swells. Pulse Width Modulation Technique is very critical for proper control of DVR. Sinusoidal Pulse Width Modulation (SPWM and Space Vector Pulse Width Modulation (SVPWM control techniques are used for controlling the DVR. Inthis work, the operation of DVR is presented and the control technique used for voltage source inverter is Space Vector PWM technique. Space vector PWM can utilize the better dc voltage and generates the fewer harmonic in inverter output voltage than Sinusoidal PWM technique. This work describes the DVR based on Space Vector PWM which provides voltage support to sensitive loads and is simulated by using MATLAB/SIMULINK. Simulation results show that the control approach is able to compensate for any type of voltage sags and swells.

  5. Irreversible electroporation ablation area enhanced by synergistic high- and low-voltage pulses

    Science.gov (United States)

    2017-01-01

    Irreversible electroporation (IRE) produced by a pulsed electric field can ablate tissue. In this study, we achieved an enhancement in ablation area by using a combination of short high-voltage pulses (HVPs) to create a large electroporated area and long low-voltage pulses (LVPs) to ablate the electroporated area. The experiments were conducted in potato tuber slices. Slices were ablated with an array of four pairs of parallel steel electrodes using one of the following four electric pulse protocols: HVP, LVP, synergistic HVP+LVP (SHLVP) or LVP+HVP. Our results showed that the SHLVPs more effectively necrotized tissue than either the HVPs or LVPs, even when the SHLVP dose was the same as or lower than the HVP or LVP doses. The HVP and LVP order mattered and only HVPs+LVPs (SHLVPs) treatments increased the size of the ablation zone because the HVPs created a large electroporated area that was more susceptible to the subsequent LVPs. Real-time temperature change monitoring confirmed that the tissue was non-thermally ablated by the electric pulses. Theoretical calculations of the synergistic effects of the SHLVPs on tissue ablation were performed. Our proposed SHLVP protocol provides options for tissue ablation and may be applied to optimize the current clinical IRE protocols. PMID:28253331

  6. Volume Diffuse Dielectric Barrier Discharge Plasma Produced by Nanosecond High Voltage Pulse in Airflow

    Institute of Scientific and Technical Information of China (English)

    QI Haicheng; GAO Wei; FAN Zhihui; LIU Yidi; REN Chunsheng

    2016-01-01

    Volume diffuse dielectric barrier discharge (DBD) plasma is produced in subsonic airflow by nanosecond high-voltage pulse power supply with a plate-to-plate discharge cell at 6 mm air gap length.The discharge images,optical emission spectra (OES),the applied voltage and current waveforms of the discharge at the changed airflow rates are obtained.When airflow rate is increased,the transition of the discharge mode and the variations of discharge intensity,breakdown characteristics and the temperature of the discharge plasma are investigated.The results show that the discharge becomes more diffuse,discharge intensity is decreased accompanied by the increased breakdown voltage and time lag,and the temperature of the discharge plasma reduces when airflow of small vclocity is introduced into the discharge gap.These phenomena are because that the airflow changes the spatial distribution of the heat and the space charge in the discharge gap.

  7. Volume Diffuse Dielectric Barrier Discharge Plasma Produced by Nanosecond High Voltage Pulse in Airflow

    Science.gov (United States)

    Qi, Haicheng; Gao, Wei; Fan, Zhihui; Liu, Yidi; Ren, Chunsheng

    2016-05-01

    Volume diffuse dielectric barrier discharge (DBD) plasma is produced in subsonic airflow by nanosecond high-voltage pulse power supply with a plate-to-plate discharge cell at 6 mm air gap length. The discharge images, optical emission spectra (OES), the applied voltage and current waveforms of the discharge at the changed airflow rates are obtained. When airflow rate is increased, the transition of the discharge mode and the variations of discharge intensity, breakdown characteristics and the temperature of the discharge plasma are investigated. The results show that the discharge becomes more diffuse, discharge intensity is decreased accompanied by the increased breakdown voltage and time lag, and the temperature of the discharge plasma reduces when airflow of small velocity is introduced into the discharge gap. These phenomena are because that the airflow changes the spatial distribution of the heat and the space charge in the discharge gap. supported by National Natural Science Foundation of China (No. 51437002)

  8. Effect of DC voltage pulses on memristor behavior.

    Energy Technology Data Exchange (ETDEWEB)

    Evans, Brian R.

    2013-10-01

    Current knowledge of memristor behavior is limited to a few physical models of which little comprehensive data collection has taken place. The purpose of this research is to collect data in search of exploitable memristor behavior by designing and implementing tests on a HP Labs Rev2 Memristor Test Board. The results are then graphed in their optimal format for conceptualizing behavioral patterns. This series of experiments has concluded the existence of an additional memristor state affecting the behavior of memristors when pulsed with positively polarized DC voltages. This effect has been observed across multiple memristors and data sets. The following pages outline the process that led to the hypothetical existence and eventual proof of this additional state of memristor behavior.

  9. Pulsed voltage electrospray ion source and method for preventing analyte electrolysis

    Science.gov (United States)

    Kertesz, Vilmos; Van Berkel, Gary

    2011-12-27

    An electrospray ion source and method of operation includes the application of pulsed voltage to prevent electrolysis of analytes with a low electrochemical potential. The electrospray ion source can include an emitter, a counter electrode, and a power supply. The emitter can include a liquid conduit, a primary working electrode having a liquid contacting surface, and a spray tip, where the liquid conduit and the working electrode are in liquid communication. The counter electrode can be proximate to, but separated from, the spray tip. The power system can supply voltage to the working electrode in the form of a pulse wave, where the pulse wave oscillates between at least an energized voltage and a relaxation voltage. The relaxation duration of the relaxation voltage can range from 1 millisecond to 35 milliseconds. The pulse duration of the energized voltage can be less than 1 millisecond and the frequency of the pulse wave can range from 30 to 800 Hz.

  10. Effect of pulsed corona discharge voltage and feed gas flow rate on dissolved ozone concentration

    Energy Technology Data Exchange (ETDEWEB)

    Prasetyaningrum, A., E-mail: ajiprasetyaningrum@gmail.com; Ratnawati,; Jos, B. [Department of Chemical Engineering, Faculty of Engineering, Diponegoro University Jl. Prof. H. Soedarto Tembalang, Semarang, Central Java, Indonesia, 50276 (Indonesia)

    2015-12-29

    Ozonization is one of the methods extensively used for water purification and degradation of organic materials. Ozone (O{sub 3}) is recognized as a powerful oxidizing agent. Due to its strong oxidability and better environmental friendless, ozone increasing being used in domestic and industrial applications. Current technology in ozone production utilizes several techniques (corona discharge, ultra violet radiation and electrolysis). This experiment aimed to evaluating effect of voltage and gas flow rate on ozone production with corona discharge. The system consists of two net-type stainless steel electrode placed in a dielectric barrier. Three pulsed voltage (20, 30, 40 KV) and flow rate (5, 10, 15 L/min) were prepare for operation variable at high frequency (3.7 kHz) with AC pulsed power supply. The dissolved ozone concentration depends on the applied high-voltage level, gas flow rate and the discharge exposure duration. The ozone concentration increases with decreasing gas flow rate. Dissolved ozone concentrations greater than 200 ppm can be obtained with a minimum voltage 40 kV.

  11. Note: Complementary metal-oxide-semiconductor high voltage pulse generation circuits.

    Science.gov (United States)

    Sun, Jiwei; Wang, Pingshan

    2013-10-01

    We present two types of on-chip pulse generation circuits. The first is based on CMOS pulse-forming-lines (PFLs). It includes a four-stage charge pump, a four-stacked-MOSFET switch and a 5 mm long PFL. The circuit is implemented in a 0.13 μm CMOS process. Pulses of ~1.8 V amplitude with ~135 ps duration on a 50 Ω load are obtained. The obtained voltage is higher than 1.6 V, the rated operating voltage of the process. The second is a high-voltage Marx generator which also uses stacked MOSFETs as high voltage switches. The output voltage is 11.68 V, which is higher than the highest breakdown voltage (~10 V) of the CMOS process. These results significantly extend high-voltage pulse generation capabilities of CMOS technologies.

  12. The effect of high voltage, high frequency pulsed electric field on slain ovine cortical bone.

    Science.gov (United States)

    Asgarifar, Hajarossadat; Oloyede, Adekunle; Zare, Firuz

    2014-04-01

    High power, high frequency pulsed electric fields known as pulsed power (PP) has been applied recently in biology and medicine. However, little attention has been paid to investigate the application of pulse power in musculoskeletal system and its possible effect on functional behavior and biomechanical properties of bone tissue. This paper presents the first research investigating whether or not PP can be applied safely on bone tissue as a stimuli and what will be the possible effect of these signals on the characteristics of cortical bone by comparing the mechanical properties of this type of bone pre and post expose to PP and in comparison with the control samples. A positive buck-boost converter was applied to generate adjustable high voltage, high frequency pulses (up to 500 V and 10 kHz). The functional behavior of bone in response to pulse power excitation was elucidated by applying compressive loading until failure. The stiffness, failure stress (strength) and the total fracture energy (bone toughness) were determined as a measure of the main bone characteristics. Furthermore, an ultrasonic technique was applied to determine and comprise bone elasticity before and after pulse power stimulation. The elastic property of cortical bone samples appeared to remain unchanged following exposure to pulse power excitation for all three orthogonal directions obtained from ultrasonic technique and similarly from the compression test. Nevertheless, the compressive strength and toughness of bone samples were increased when they were exposed to 66 h of high power pulsed electromagnetic field compared to the control samples. As the toughness and the strength of the cortical bone tissue are directly associated with the quality and integrity of the collagen matrix whereas its stiffness is primarily related to bone mineral content these overall results may address that although, the pulse power stimulation can influence the arrangement or the quality of the collagen network

  13. Mechanism of formation of subnanosecond current front in high-voltage pulse open discharge

    Science.gov (United States)

    Schweigert, I. V.; Alexandrov, A. L.; Zakrevsky, Dm. E.; Bokhan, P. A.

    2014-11-01

    The mechanism of subnanosecond current front rise observed previously in the experiment in high-voltage pulse open discharge in helium is studied in kinetic particle-in-cell simulations. The Boltzmann equations for electrons, ions, and fast atoms are solved self-consistently with the Poisson equations for the electrical potential. The partial contributions to the secondary electron emission from the ions, fast atoms, photons, and electrons, bombarding the electrode, are calculated. In simulations, as in the experiment, the discharge glows between two symmetrical cathodes and the anode grid in the midplane at P =6 Torr and the applied voltage of 20 kV. The electron avalanche development is considered for two experimental situations during the last stage of breakdown: (i) with constant voltage and (ii) with decreasing voltage. For case (i), the subnanosecond current front rise is set by photons from the collisional excitation transfer reactions. For the case (ii), the energetic electrons swamp the cathode during voltage drop and provide the secondary electron emission for the subnanosecond current rise, observed in the experiment.

  14. Development of high-voltage pulse generator with variable amplitude and duration

    Science.gov (United States)

    Upadhyay, J.; Sharma, M. L.; Ahuja, Aakash B.; Navathe, C. P.

    2014-06-01

    A high voltage pulse generator with variable amplitude (100-3000 V) and duration (100-2000 μs) has been designed and developed. The variable duration pulse has been generated by adopting a simple and novel technique of varying the turn off delay time of a high voltage Metal Oxide Semiconductor Field Effect Transistor (MOSFET) based switch by varying external gate resistance. The pulse amplitude is made variable by adjusting biasing supply of the high voltage switch. The high voltage switch has been developed using a MOSFET based stack of 3 kV rating with switching time of 7 ns.

  15. A pulsed magnetic stress applied to Drosophila melanogaster flies

    Science.gov (United States)

    Delle Side, D.; Bozzetti, M. P.; Friscini, A.; Giuffreda, E.; Nassisi, V.; Specchia, V.; Velardi, L.

    2014-04-01

    We report the development of a system to feed pulsed magnetic stress to biological samples. The device is based on a RLC circuit that transforms the energy stored in a high voltage capacitor into a magnetic field inside a coil. The field has been characterized and we found that charging the capacitor with 24 kV results in a peak field of 0.4 T. In order to test its effect, we applied such a stress to the Drosophila melanogaster model and we examined its bio-effects. We analysed, in the germ cells, the effects on the control of specific DNA repetitive sequences that are activated after different environmental stresses. The deregulation of these sequences causes genomic instability and chromosomes breaks leading to sterility. The magnetic field treatment did not produce effects on repetitive sequences in the germ cells of Drosophila. Hence, this field doesn't produce deleterious effects linked to repetitive sequences derepression.

  16. Transverse voltage in superconductors at zero applied magnetic field

    Energy Technology Data Exchange (ETDEWEB)

    Luz, M.S. da [Escola de Engenharia de Lorena - USP, P.O. Box 116, Lorena, SP 12602-810 (Brazil)], E-mail: luz@physics.montana.edu; Santos, C.A.M. dos; Shigue, C.Y.; Carvalho, F.J.H. de; Machado, A.J.S. [Escola de Engenharia de Lorena - USP, P.O. Box 116, Lorena, SP 12602-810 (Brazil)

    2009-01-01

    A systematic study of the transverse voltage at zero magnetic field in the superconducting state is reported. The effects of warming rate, temperature, applied magnetic field, and electrical current on the transversal resistance (R{sub XY}) of polycrystalline superconducting sample are taken into account. At zero magnetic field two peaks are observed in R{sub XY}(T) curves which are related to the double superconducting transition in the R{sub XX}(T) component. In the superconducting (R{sub XX} = zero) and normal states no transverse voltage has been detected at zero magnetic field as expected. The results are discussed within the framework of the motion of Abrikosov and Josephson vortices and anti-vortices. A new scaling relation between transverse and longitudinal components given by R{sub XY} {approx} dR{sub XX}/dT has been confirmed.

  17. Modeling of dielectric barrier discharge excimer lamp excited by mono polar voltage pulses

    Science.gov (United States)

    Akashi, Haruaki; Oda, Akinori; Sakai, Yosuke

    2007-10-01

    Filametal discharges in Dielectric Barrier Discharge (DBD) excimer lamp excited by mono polar voltage pulses has been simulated using two dimensional fluid model. And the differences of the filament discharges formations between mono polar case and bipolar case [1] have been examined. Xe gas was used and its pressure is 300Torr. Simulated region is 1cm (gap length) x 3cm (radial length). Periodical boundary conditions are assumed for the radial direction boundaries. The both electrodes are covered with dielectrics and their thickness is 0.2cm. Applied voltage is 5kV trapezoid shape with 50% duty ratio waveform and its repetition rate is 200kpps. First a small amount of electron-ion pair is provided in the middle of the gap for initial condition. Then the voltage starts to apply. In the case of bipolar excitation, the discharge starts from one filament (streamer discharge), and finally, 5 filaments are obtained self-consistently. In the case of mono polar case, as first, similar to bipolar case, the discharge starts from one filament, however, only 3 filaments have been obtained. This result is similar to that of 100kHz bipolar voltage case. [1] H. Akashi et al, IEEE Trans. Plasma Science, Vol.33, No.2 (2005) pp.308-309

  18. Voltage-pulsed and laser-pulsed atom probe tomography of a multiphase high-strength low-carbon steel.

    Science.gov (United States)

    Mulholland, Michael D; Seidman, David N

    2011-12-01

    The differences in artifacts associated with voltage-pulsed and laser-pulsed (wavelength = 532 or 355 nm) atom-probe tomographic (APT) analyses of nanoscale precipitation in a high-strength low-carbon steel are assessed using a local-electrode atom-probe tomograph. It is found that the interfacial width of nanoscale Cu precipitates increases with increasing specimen apex temperatures induced by higher laser pulse energies (0.6-2 nJ pulse(-1) at a wavelength of 532 nm). This effect is probably due to surface diffusion of Cu atoms. Increasing the specimen apex temperature by using pulse energies up to 2 nJ pulse(-1) at a wavelength of 532 nm is also found to increase the severity of the local magnification effect for nanoscale M2C metal carbide precipitates, which is indicated by a decrease of the local atomic density inside the carbides from 68 ± 6 nm(-3) (voltage pulsing) to as small as 3.5 ± 0.8 nm(-3). Methods are proposed to solve these problems based on comparisons with the results obtained from voltage-pulsed APT experiments. Essentially, application of the Cu precipitate compositions and local atomic density of M2C metal carbide precipitates measured by voltage-pulsed APT to 532 or 355 nm wavelength laser-pulsed data permits correct quantification of precipitation.

  19. Electron tunnelling through single azurin molecules can be on/off switched by voltage pulses

    Science.gov (United States)

    Baldacchini, Chiara; Kumar, Vivek; Bizzarri, Anna Rita; Cannistraro, Salvatore

    2015-05-01

    Redox metalloproteins are emerging as promising candidates for future bio-optoelectronic and nano-biomemory devices, and the control of their electron transfer properties through external signals is still a crucial task. Here, we show that a reversible on/off switching of the electron current tunnelling through a single protein can be achieved in azurin protein molecules adsorbed on gold surfaces, by applying appropriate voltage pulses through a scanning tunnelling microscope tip. The observed changes in the hybrid system tunnelling properties are discussed in terms of long-sustained charging of the protein milieu.

  20. Electron tunnelling through single azurin molecules can be on/off switched by voltage pulses

    Energy Technology Data Exchange (ETDEWEB)

    Baldacchini, Chiara [Biophysics and Nanoscience Centre, DEB-CNISM, Università della Tuscia, I-01100 Viterbo (Italy); Institute of Agro-Environmental and Forest Biology, CNR, I-05010 Porano (Italy); Kumar, Vivek; Bizzarri, Anna Rita; Cannistraro, Salvatore, E-mail: cannistr@unitus.it [Biophysics and Nanoscience Centre, DEB-CNISM, Università della Tuscia, I-01100 Viterbo (Italy)

    2015-05-04

    Redox metalloproteins are emerging as promising candidates for future bio-optoelectronic and nano-biomemory devices, and the control of their electron transfer properties through external signals is still a crucial task. Here, we show that a reversible on/off switching of the electron current tunnelling through a single protein can be achieved in azurin protein molecules adsorbed on gold surfaces, by applying appropriate voltage pulses through a scanning tunnelling microscope tip. The observed changes in the hybrid system tunnelling properties are discussed in terms of long-sustained charging of the protein milieu.

  1. A Pulsed Power Supply with Sag Compensation using Controlled Gradational Voltage

    Science.gov (United States)

    Suzuki, Akihiro; Yamada, Masaki; Tashiro, Shojirou; Iwata, Akihiko

    A pulsed power supply with sag compensation using controlled gradational voltage to increase the flatness of output waveforms has been developed.The sag compensation circuit consists of compensation units connected in series. Each compensation unit consists of capacitances, diodes, and semiconductor switches. The capacitances of each unit are charged with different voltages by 2n (V0, 2V0, 4V0, ···). The compensation voltages, which has 2n-1 steps, is generated by switching the semiconductor switches of each unit in a binary sequence. Using this method, compensation voltage waveforms up to 6.2kV with 31 steps can be obtained with 5 compensation units. The sag compensation circuit has been adapted to a direct switch type pulsed power supply, which generates 7kV pulsed voltage with a pulse width of 700μs, thus realizing sag compensation.

  2. Investigation of low-voltage pulse parameters on electroporation and electrical lysis using a microfluidic device with interdigitated electrodes.

    Science.gov (United States)

    Morshed, Bashir I; Shams, Maitham; Mussivand, Tofy

    2014-03-01

    Electroporation (EP) of biological cells leads to the exchange of materials through the permeabilized cell membrane, while electrical lysis (EL) irreversibly disrupts the cell membrane. We report a microfluidic device to study these two phenomena with low-voltage excitation for lab-on-a-chip (LOC) applications. For systematic study of EP, we have employed a quantification metric: flow Index (FI) of EP. Simulation and experimental results with the microfluidic device containing interdigitated, coplanar, integrated electrodes to electroporate, and rapidly lyse biological cells are presented. H&E stained human buccal cells were subjected to various pulse magnitudes, pulsewidths, and number of pulses. Simulations show that an electric field of 25 kV/cm with a 20 V applied potential produced 1.3 (°)C temperature rise for a 5 s of excitation. For a 20 V pulse-excitation with pulse-widths between 0.5 to 5 s, EL was observed, whereas for lower excitations, only EP was observed. FI of EP is found to be a direct function of pulse magnitudes, pulsewidths, and numbers of pulses. To release DNA from nucleus, excitation-pulses of 5 s were required. Quantification of EP would be useful for systematic study of EP toward optimization with various excitation pulses, while low-voltage requirement and high yield of EP and EL are critical to develop LOC for drug delivery and cell-sample preparation, respectively.

  3. Review of the Dynamics of Coalescence and Demulsification by High-Voltage Pulsed Electric Fields

    Directory of Open Access Journals (Sweden)

    Ye Peng

    2016-01-01

    Full Text Available The coalescence of droplets in oil can be implemented rapidly by high-voltage pulse electric field, which is an effective demulsification dehydration technological method. At present, it is widely believed that the main reason of pulse electric field promoting droplets coalescence is the dipole coalescence and oscillation coalescence in pulse electric field, and the optimal coalescence pulse electric field parameters exist. Around the above content, the dynamics of high-voltage pulse electric field promoting the coalescence of emulsified droplets is studied by researchers domestically and abroad. By review, the progress of high-voltage pulse electric field demulsification technology can get a better understanding, which has an effect of throwing a sprat to catch a whale on promoting the industrial application.

  4. Plasma density enhancement in atmospheric-pressure dielectric-barrier discharges by high-voltage nanosecond pulse in the pulse-on period: a PIC simulation

    Science.gov (United States)

    Sang, Chaofeng; Sun, Jizhong; Wang, Dezhen

    2010-02-01

    A particle-in-cell (PIC) plus Monte Carlo collision simulation is employed to investigate how a sustainable atmospheric pressure single dielectric-barrier discharge responds to a high-voltage nanosecond pulse (HVNP) further applied to the metal electrode. The results show that the HVNP can significantly increase the plasma density in the pulse-on period. The ion-induced secondary electrons can give rise to avalanche ionization in the positive sheath, which widens the discharge region and enhances the plasma density drastically. However, the plasma density stops increasing as the applied pulse lasts over certain time; therefore, lengthening the pulse duration alone cannot improve the discharge efficiency further. Physical reasons for these phenomena are then discussed.

  5. DESIGN NOTE: A fast high-voltage pulse generator with variable amplitude and duration

    Science.gov (United States)

    Upadhyay, Jankee; Navathe, C. P.

    2006-07-01

    A high-voltage pulse generator based on a self-matched transmission line with variable pulse amplitude and duration is developed. Two avalanche transistor stacks are used as switches. The pulse width is varied by adjusting the delay in triggering two switches whereas amplitude is adjusted by adjusting load resistance. A pulse with amplitude of 800 V to 3.8 kV and width of 5 ns to 38 ns can be obtained using this circuit.

  6. Comparison of the quantitative analysis performance between pulsed voltage atom probe and pulsed laser atom probe.

    Science.gov (United States)

    Takahashi, J; Kawakami, K; Raabe, D

    2017-01-31

    The difference in quantitative analysis performance between the voltage-mode and laser-mode of a local electrode atom probe (LEAP3000X HR) was investigated using a Fe-Cu binary model alloy. Solute copper atoms in ferritic iron preferentially field evaporate because of their significantly lower evaporation field than the matrix iron, and thus, the apparent concentration of solute copper tends to be lower than the actual concentration. However, in voltage-mode, the apparent concentration was higher than the actual concentration at 40K or less due to a detection loss of matrix iron, and the concentration decreased with increasing specimen temperature due to the preferential evaporation of solute copper. On the other hand, in laser-mode, the apparent concentration never exceeded the actual concentration, even at lower temperatures (20K), and this mode showed better quantitative performance over a wide range of specimen temperatures. These results indicate that the pulsed laser atom probe prevents both detection loss and preferential evaporation under a wide range of measurement conditions.

  7. Initial position estimation method for permanent magnet synchronous motor based on improved pulse voltage injection

    DEFF Research Database (Denmark)

    Wang, Z.; Lu, K.; Ye, Y.

    2011-01-01

    According to saliency of permanent magnet synchronous motor (PMSM), the information of rotor position is implied in performance of stator inductances due to the magnetic saturation effect. Researches focused on the initial rotor position estimation of PMSM by injecting modulated pulse voltage...... vectors. The relationship between the inductance variations and voltage vector positions was studied. The inductance variation effect on estimation accuracy was studied as well. An improved five-pulses injection method was proposed, to improve the estimation accuracy by choosing optimaized voltage vectors...

  8. Correction factor based double model fuzzy logic control strategy of arc voltage in pulsed MIG welding

    Institute of Scientific and Technical Information of China (English)

    Wu Kaiyuan; Huang Shisheng; Meng Yongmin

    2005-01-01

    According to the feature of arc voltage control in welding steel using pulsed MIG welding, a correction factor based double model fuzzy logic controller (FLC) was developed to realize the arc voltage control by means of arc voltage feedback.When the error of peak arc voltage was great, a coarse adjusting fuzzy logic control rules with correction factor was designed,in the controller, the peak arc voltage was controlled by the wire feeding speed by means of arc voltage feedback. When the error of peak arc voltage was small, a fine adjusting fuzzy logic control rules with correction factor was designed, in this controller, the peak arc voltage was controlled by the background time by means of arc voltage feedback. The FLC was realized in a Look-Up Table ( LUT) method. Experiments had been carried out aiming at implementing the control strategy to control the arc length change in welding process. Experimental results show that the controller proposed enables the consistency of arc length and the stabolity of arc voltage and welding process to be achieved in pulsed MIG welding process.

  9. New Control Technique Applied in Dynamic Voltage Restorer for Voltage Sag Mitigation

    Directory of Open Access Journals (Sweden)

    Rosli Omar

    2010-01-01

    Full Text Available The Dynamic Voltage Restorer (DVR was a power electronics device that was able to compensate voltage sags on critical loads dynamically. The DVR consists of VSC, injection transformers, passive filters and energy storage (lead acid battery. By injecting an appropriate voltage, the DVR restores a voltage waveform and ensures constant load voltage. There were so many types of the control techniques being used in DVR for mitigating voltage sags. The efficiency of the DVR depends on the efficiency of the control technique involved in switching the inverter. Problem statement: Simulation and experimental investigation toward new algorithms development based on SVPWM. Understanding the nature of DVR and performance comparisons between the various controller technologies available. The proposed controller using space vector modulation techniques obtain higher amplitude modulation indexes if compared with conventional SPWM techniques. Moreover, space vector modulation techniques can be easily implemented using digital processors. Space vector PWM can produce about 15% higher output voltage than standard Sinusoidal PWM. Approach: The purpose of this research was to study the implementation of SVPWM in DVR. The proposed control algorithm was investigated through computer simulation by using PSCAD/EMTDC software. Results: From simulation and experimental results showed the effectiveness and efficiency of the proposed controller based on SVPWM in mitigating voltage sags in low voltage distribution systems. It was concluded that its controller also works well both in balance and unbalance conditions of voltages. Conclusion/Recommendations: The simulation and experimental results of a DVR using PSCAD/EMTDC software based on SVPWM technique showed clearly the performance of the DVR in mitigating voltage sags. The DVR operates without any difficulties to inject the appropriate voltage component to correct rapidly any anomaly in the supply voltage to keep the

  10. Novel design of high voltage pulse source for efficient dielectric barrier discharge generation by using silicon diodes for alternating current

    Science.gov (United States)

    Truong, Hoa Thi; Hayashi, Misaki; Uesugi, Yoshihiko; Tanaka, Yasunori; Ishijima, Tatsuo

    2017-06-01

    This work focuses on design, construction, and optimization of configuration of a novel high voltage pulse power source for large-scale dielectric barrier discharge (DBD) generation. The pulses were generated by using the high-speed switching characteristic of an inexpensive device called silicon diodes for alternating current and the self-terminated characteristic of DBD. The operation started to be powered by a primary DC low voltage power supply flexibly equipped with a commercial DC power supply, or a battery, or DC output of an independent photovoltaic system without transformer employment. This flexible connection to different types of primary power supply could provide a promising solution for the application of DBD, especially in the area without power grid connection. The simple modular structure, non-control requirement, transformer elimination, and a minimum number of levels in voltage conversion could lead to a reduction in size, weight, simple maintenance, low cost of installation, and high scalability of a DBD generator. The performance of this pulse source has been validated by a load of resistor. A good agreement between theoretically estimated and experimentally measured responses has been achieved. The pulse source has also been successfully applied for an efficient DBD plasma generation.

  11. High voltage pulse cable and connector experience in the kicker systems at SLAC

    Energy Technology Data Exchange (ETDEWEB)

    Harris, K.; Artusy, M.; Donaldson, A.; Mattison, T.

    1991-05-01

    The SLAC 2-mile linear accelerator uses a wide variety of pulse kicker systems that require high voltage cable and connectors to deliver pulses from the drivers to the magnet loads. Many of the drivers in the SLAC kicker systems use cable lengths up to 80 feet and are required to deliver pulses up to 40 kV, with rise and fall time on the order of 20 ns. Significant pulse degradation from the cable and connector assembly cannot be tolerated. Other drivers are required to deliver up to 80 kV, 20 {mu}s pulses over cables 20 feet long. Several combinations of an applicable high voltage cable and matching connector have been used at SLAC to determine the optimum assembly that meets the necessary specifications and is reliable. 14 refs., 3 figs., 1 tab.

  12. Evolution of nanosecond surface dielectric barrier discharge for negative polarity of a voltage pulse

    Science.gov (United States)

    Soloviev, V. R.; Krivtsov, V. M.; Shcherbanev, S. A.; Starikovskaia, S. M.

    2017-01-01

    Surface dielectric barrier discharge, initiated by a high-voltage pulse of negative polarity in atmospheric pressure air, is studied numerically and experimentally. At a pulse duration of a few tens of nanoseconds, two waves of optical emission propagate from the high-voltage electrode corresponding to the leading and trailing edges of the high-voltage pulse. It is shown by means of numerical modeling that a glow-like discharge slides along the surface of the dielectric at the leading edge of the pulse, slowing down on the plateau of the pulse. When the trailing edge of the pulse arrives to the high-voltage electrode, a second discharge starts and propagates in the same direction. The difference is that the discharge corresponding to the trailing edge is not diffuse and demonstrates a well-pronounced streamer-like shape. The 2D (in numerical modeling) streamer propagates above the dielectric surface, leaving a gap of about 0.05 mm between the streamer and the surface. The calculated and experimentally measured emission picture, waveform of the electrical current, and deposited energy, qualitatively coincide. The sensitivity of the numerical solution to unknown physical parameters of the model is discussed.

  13. Synthesis gas regeneration electrotechnology using volume high-voltage pulsed discharges: corona and barrier ones

    Directory of Open Access Journals (Sweden)

    M.I. Boyko

    2014-09-01

    Full Text Available Factory testing of a created high-voltage complex (plant has been conducted. The complex consists of two pulse generators with the repetition rate of up to 50,000 pulses per second and load reactors with pulsed discharges - corona and barrier ones. Transistor (IGBT keys are used as energy switches. The efficient mode of coke gas methane conversion (steam reforming to syngas has been obtained with application of the complex created. A unidirectional action of the pulsed discharges, the gas mixture temperature, and a nickel catalyst has reduced the specific energy consumption for synthesis gas regeneration during the conversion. A feasible mechanism of this conversion is described.

  14. Solid-state fast voltage compensator for pulsed power applications requiring constant AC power consumption

    CERN Document Server

    Magallanes, Francisco Cabaleiro; Viarouge, Philippe; Cros, Jérôme

    2015-01-01

    This paper proposes a novel topological solution for pulsed power converters based on capacitor-discharge topologies, integrating a Fast Voltage Compensator which allows an operation at constant power consumption from the utility grid. This solution has been retained as a possible candidate for the CLIC project under study at CERN, which requires more than a thousand synchronously-operated klystron modulators producing a total pulsed power of almost 40 GW. The proposed Fast Voltage Compensator is integrated in the modulator such that it only has to treat the capacitor charger current and a fraction of the charging voltage, meaning that its dimensioning power and cost are minimized. This topology can be used to improve the AC power quality of any pulsed converters based on capacitor-discharge concept. A prototype has been built and exploited to validate the operating principle and demonstrate the benefits of the proposed solution.

  15. Variable Voltage Source Inverter with controlled frequency spectrum based on Random Pulse Width Modulation

    Directory of Open Access Journals (Sweden)

    Muhammad Farrukh Yaqub

    2012-01-01

    Full Text Available This paper presents a new method for single phase variable voltage inverter based on Random Pulse Width Modulation. In Random Pulse Width Modulation based inverter, the frequency spectrum of the output current and voltage waveforms becomes continuous because of the randomization of the switching function of the devices controlling the output voltages. This paper establishes a theory that if the distributions of the random numbers generated by the random source are kept within certain limit with respect to the peak value of reference sinusoidal waveform, the frequency spectrum can be controlled. On the basis of the results, a novel drive using variable tap changing transformer (optional and adaptive random number generator, to control the ratio between the numbers generated by the random source and the reference waveform has been suggested that will guarantee a better power quality profile for a broad range of output voltages.

  16. Pulsed high voltage electric discharge disinfection of microbially contaminated liquids.

    Science.gov (United States)

    Anpilov, A M; Barkhudarov, E M; Christofi, N; Kop'ev, V A; Kossyi, I A; Taktakishvili, M I; Zadiraka, Y

    2002-01-01

    To examine the use of a novel multielectrode slipping surface discharge (SSD) treatment system, capable of pulsed plasma discharge directly in water, in killing micro-organisms. Potable water containing Escherichia coli and somatic coliphages was treated with pulsed electric discharges generated by the SSD. The SSD system was highly efficient in the microbial disinfection of water with a low energy utilization (eta approximately 10-4 kW h l-1). The SSD treatment was effective in the destruction of E. coli and its coliphages through the generation of u.v. radiation, ozone and free radicals. The non-thermal treatment method can be used for the eradication of micro-organisms in a range of contaminated liquids, including milk, negating the use of pasteurization. The method utilizes multipoint electric discharges capable of treating large volumes of liquid under static and flowing regimes.

  17. Bipolar generator of voltage pulses of amplitude + or - 600 kV

    Energy Technology Data Exchange (ETDEWEB)

    Bannikov, A.V.; Dzhavrishvili, A.K.; Kharchilava, A.I.; Lomtadze, T.A.; Vertogradov, L.S.

    1985-09-01

    This paper describes the design of a 25-stage pulsed-voltage generator (+ or - 600 kV) of the Arkad'ev-Marx type. The generator is used in the high-voltage power supply system of a five-meter, three-gap streamer chamber. The values of the Principal parameters of the generator, per arm, are impulse capacitance 0.95 nF, internal resistance 21 ..cap omega.., and internal inductance 1.8 ..mu.. H.

  18. Electron Emission from Ferroelectric/Antiferroelectric Cathodes Excited by Short High-Voltage Pulses

    CERN Document Server

    Benedek, G; Handerek, J; Riege, H

    1997-01-01

    Un-prepoled Lead Zirconate Titanate Lanthanum doped-PLZT ferroelectric cathodes have emitted intense current pulses under the action of a high voltage pulse of typically 8 kV/cm for PLZT of 8/65/35 composition and 25 kV/cm for PLZT of 4/95/5 composition. In the experiments described in this paper, the exciting electric field applied to the sample is directed from the rear surface towards the emitting surface. The resulting emission is due to an initial field emission from the metal of the grid deposited over the emitting surface with the consequent plasma formation and the switching of ferroelectric domains. These electrons may be emitted directly form the crystal or from the plasma. This emission requires the material in ferroelectric phase. In fact, PLZT cathodes of the 8/65/35 type, that is with high Titanium content, showing ferroelectric-paraelectric phase sequence, emit at room temperature, while PLZT cathodes of the 4/95/5 type, that is with low Titanium content, having antiferro-ferro-paraelectric pha...

  19. Effects of High-voltage Pulse Electric Field Treatment on the Structure Stability of Konjac Glucomannan

    Institute of Scientific and Technical Information of China (English)

    YAO Min-Na; FAN Lin-Lin; LIU Ya-Nan; CHEN Qing-Ai; ZENG Yuan; JIAN Wen-Jie; PANG Jie

    2011-01-01

    Structures of KGM treated in two high-voltage pulse electric fields were characterized by infrared spectroscopy,Raman spectroscopy,X-ray diffraction and so on.The results showed that intermolecular hydrogen bonding interactions of KGM were reduced after being treated with high-voltage pulse electric field,but there was no significant effect on its fiber chain form and thermal characteristics.Results of the study can provide a useful reference for further study on the structure and property of KGM,and especially can provide theoretical basis for the effect of physical field on the foodstuff deep processing related to KGM.

  20. MOSFET-based high voltage double square-wave pulse generator with an inductive adder configuration

    Energy Technology Data Exchange (ETDEWEB)

    Zhao, Xin [State Key Laboratory of Electrical Insulation and Power Equipment, Xi' an Jiaotong University, Xi' an 710049 (China); Zhang, Qiaogen, E-mail: hvzhang@mail.xjtu.edu.cn [State Key Laboratory of Electrical Insulation and Power Equipment, Xi' an Jiaotong University, Xi' an 710049 (China); Long, Jinghua [College of Physics, Shenzhen University, Shenzhen 518060 (China); Lei, Yunfei; Liu, Jinyuan [Institute of Optoelectronics, Shenzhen University, Shenzhen 518060 (China)

    2015-09-01

    This paper presents a fast MOSFET-based solid-state pulse generator for high voltage double square-wave pulses. The generator consists mainly of an inductive adder system stacked of 20 solid-state modules. Each of the modules has 18 power MOSFETs in parallel, which are triggered by individual drive circuits; these drive circuits themselves are synchronously triggered by a signal from avalanche transistors. Our experiments demonstrate that the output pulses with amplitude of 8.1 kV and peak current of about 405 A are available at a load impedance of 20 Ω. The pulse has a double square-wave form with a rise and fall time of 40 ns and 26 ns, respectively and bottom flatness better than 12%. The interval time of the double square-wave pulses can be adjustable by varying the interval time of the trigger pulses.

  1. Optimized Controller Design for a 12-Pulse Voltage Source Converter Based HVDC System

    Science.gov (United States)

    Agarwal, Ruchi; Singh, Sanjeev

    2017-08-01

    The paper proposes an optimized controller design scheme for power quality improvement in 12-pulse voltage source converter based high voltage direct current system. The proposed scheme is hybrid combination of golden section search and successive linear search method. The paper aims at reduction of current sensor and optimization of controller. The voltage and current controller parameters are selected for optimization due to its impact on power quality. The proposed algorithm for controller optimizes the objective function which is composed of current harmonic distortion, power factor, and DC voltage ripples. The detailed designs and modeling of the complete system are discussed and its simulation is carried out in MATLAB-Simulink environment. The obtained results are presented to demonstrate the effectiveness of the proposed scheme under different transient conditions such as load perturbation, non-linear load condition, voltage sag condition, and tapped load fault under one phase open condition at both points-of-common coupling.

  2. Influences of Excess Oscillation of Voltage Pulse and Discharge Mode on NO Removal Using Barrier-Type Plasma Reactor

    Science.gov (United States)

    Kadowaki, Kazunori; Suzuki, Yoshiaki; Ihori, Haruo; Kitani, Isamu

    This paper presents experimental results of NO removal from a simulated exhausted-gas using a barrier type reactor with screw electrodes subjected to polarity-reversed voltage pulses. The polarity-reversed pulse was produced by direct grounding of a charged coaxial cable because a traveling wave voltage was negatively reflected at the grounding end with a change in its polarity and then it propagated to the plasma reactor at the opposite end. Influence of cable length on NO removal was studied for two kinds of cable connection, single-connected cable and parallel-connected cables. NO removal ratio for a 50m-long cable was lower than that for much shorter cables in both single and parallel connections when the applied voltage became high. Energy efficiency for NO removal also increased with decreasing the cable length. This was because excess discharges during the voltage oscillation caused by the large stored energy in the long cable resulted in reproduction of NO molecules. Energy efficiency was further improved by changing the discharge mode from dielectric barrier discharge (DBD) to surface discharge (SD). Energy efficiency was up to 110g/kWh with 55% NO removal ratio and 34g/kWh with 100% NO removal ratio by using a single 10m-long cable in SD mode.

  3. Effect of pulsed voltage on electrochemical migration of tin in electronics

    DEFF Research Database (Denmark)

    Verdingovas, Vadimas; Jellesen, Morten Stendahl; Ambat, Rajan

    2015-01-01

    influences the dendritic growth, although a tendency for more hydroxide precipitation was observed for lower duty cycles. The precipitation of tin hydroxides was identified as influencing factor for the reduction of charge transfer under pulsed voltage with low duty cycles, therefore resulting...... in the suppression of dendrite growth....... respectively at 10 and 5 V, while the duty cycle and the pulse width were varied in the range of ms. The results showed that varying of pulse width at fixed duty cycle has a minor effect under investigated conditions, whereas increasing duty cycle significantly reduces the time to short due to dendrite...

  4. [Negative air ions generated by plants upon pulsed electric field stimulation applied to soil].

    Science.gov (United States)

    Wu, Ren-ye; Deng, Chuan-yuan; Yang, Zhi-jian; Weng, Hai-yong; Zhu, Tie-jun-rong; Zheng, Jin-gui

    2015-02-01

    This paper investigated the capacity of plants (Schlumbergera truncata, Aloe vera var. chinensis, Chlorophytum comosum, Schlumbergera bridgesii, Gymnocalycium mihanovichii var. friedrichii, Aspidistra elatior, Cymbidium kanran, Echinocactus grusonii, Agave americana var. marginata, Asparagus setaceus) to generate negative air ions (NAI) under pulsed electric field stimulation. The results showed that single plant generated low amounts of NAI in natural condition. The capacity of C. comosum and G. mihanovichii var. friedrichii generated most NAI among the above ten species, with a daily average of 43 ion · cm(-3). The least one was A. americana var. marginata with the value of 19 ion · cm(-3). When proper pulsed electric field stimulation was applied to soil, the NAI of ten plant species were greatly improved. The effect of pulsed electric field u3 (average voltage over the pulse period was 2.0 x 10(4) V, pulse frequency was 1 Hz, and pulse duration was 50 ms) was the greatest. The mean NAI concentration of C. kanran was the highest 1454967 ion · cm(-3), which was 48498.9 times as much as that in natural condition. The lowest one was S. truncata with the value of 34567 ion · cm(-3), which was 843.1 times as much as that in natural condition. The capacity of the same plants to generate negative air ion varied extremely under different intensity pulsed electric fields.

  5. The effects of high-voltage pulse electric discharges on ion adsorption on activated carbons

    Science.gov (United States)

    Gafurov, M. M.; Sveshnikova, D. A.; Larin, S. V.; Rabadanov, K. Sh.; Shabanova, Z. E.; Yusupova, A. A.; Ramazanov, A. Sh.

    2008-07-01

    The effects of high-voltage pulse electric discharges (HPED) on sorption of boron and sulfate ions on activated carbons of different kinds (KM-2, BAU, DAK) were investigated. The effect of HPED activation on the sorption characteristics of the systems was found to be similar to the temperature effect.

  6. [An integral chip for the multiphase pulse-duration modulation used for voltage changer in biomedical microprocessor systems].

    Science.gov (United States)

    Balashov, A M; Selishchev, S V

    2004-01-01

    An integral chip (IC) was designed for controlling the step-down pulse voltage converter, which is based on the multiphase pulse-duration modulation, for use in biomedical microprocessor systems. The CMOS technology was an optimal basis for the IC designing. An additional feedback circuit diminishes the output voltage dispersion at dynamically changing loads.

  7. Simultaneously Propagating Voltage and Pressure Pulses in Lipid Monolayers of pork brain and synthetic lipids

    CERN Document Server

    Griesbauer, J; Wixforth, A; Schneider, M F

    2012-01-01

    Hydrated interfaces are ubiquitous in biology and appear on all length scales from ions, individual molecules to membranes and cellular networks. In vivo, they comprise a high degree of self-organization and complex entanglement, which limits their experimental accessibility by smearing out the individual phenomenology. The Langmuir technique, however, allows the examination of defined interfaces, whose controllable thermodynamic state enables one to explore the proper state diagrams. Here we demonstrate that voltage and pressure pulses simultaneously propagate along monolayers comprised of either native pork brain or synthetic lipids. The excitation of pulses is conducted by the application of small droplets of acetic acid and monitored subsequently employing timeresolved Wilhelmy plate and Kelvin probe measurements. The isothermal state diagrams of the monolayers for both lateral pressure and surface potential are experimentally recorded, enabling us to predict dynamic voltage pulse amplitudes of 0,1 to 3mV...

  8. Quantitative relationship between the maximum streamer length and discharge voltage of a pulsed positive streamer discharge in water

    Science.gov (United States)

    Wen, Xiaoqiong; Li, Qian; Li, Jingsen; Ren, Chunsheng

    2017-08-01

    A linear relationship has been realized between the maximum streamer length and discharge voltage of a pulsed positive streamer discharge by measuring the streamer length in water with conductivity of 100 μS cm-1 using high-speed photography. Based on Ohm’s law, a quantitative equation has been derived for the dependence of the maximum streamer length on the discharge voltage of a pulsed positive streamer discharge in water. According to the equation, our results suggest that the streamers spontaneously stop propagating through water due to the voltage at the streamer head dropping below the ignition voltage of a pulsed positive streamer discharge.

  9. Voltage Sag Mitigation Using Pulse Width Modulation Switched Autotransformer through Matlab Simulation

    Directory of Open Access Journals (Sweden)

    P. Shyam Kiran

    2014-04-01

    Full Text Available In this paper, a new voltage sag compensator for critical loads in electrical distribution system discussed. The proposed scheme employs a Pulse width modulation ac-ac converter along with a auto transformer. During a disturbance such as voltage sag, the proposed scheme supplies the missing voltage and helps in maintaining the rated voltage at the terminals of the critical load. Under normal condition the approach work in bypass mode and delivering utility power directly to load. The proposed system has less number of switching devices and has good compensating capability in comparison to commonly used compensators. Simulation analysis of three-phase compensator is performed in MATLAB/SIMULINK and performance analysis of the system is presented for various levels of sag and swell.

  10. High-voltage pulse generator with inductive energy storage and thyratron

    CERN Document Server

    Vereshchagin, N M

    2002-01-01

    The high-voltage pulse generator with the energy storage on the basis of the single layer solenoid with inductivity of 10-35 mu H is described. The TGI2-500/20 thyratron able of breaking reliably the current with the amplitude of 800-850 A was used as the current breaker. The voltage on the load is formed in two stages. The first stage is characterized by the voltage of 20-25 kV and the growth time of 150-200 m. At the second stage there takes place fast (approx 60 ns) formation of the voltage up 90 kV. The scheme of the charge quenching decreases the instability of the current breaker time

  11. Hybrid method of solution applied to simulation of pulse chromatography

    Directory of Open Access Journals (Sweden)

    M. A. Cremasco

    2009-06-01

    Full Text Available In this communication, the method proposed by Cremasco et al. (2003 is applied to predict single and low concentration pulse chromatography. In previous work, a general rate model was presented to describe the breakthrough curve, where a hybrid solution was proposed for the linear adsorption. The liquid phase concentration inside the particle was found analytically and related with the bed liquid phase through Duhamel's Theorem, while the bulk-phase equation was solved by a numerical method. In this paper, this method is applied to describe pulse chromatography of solutes that present linear adsorption isotherms. The simulated results of pulse chromatography are compared with experimental ones for aromatic amino acid experiments from literature.

  12. Influence of the Discharge Voltage during Pulse-Plasma Process on the Durability of Edges coated with Superhard Coatings

    Institute of Scientific and Technical Information of China (English)

    Maciej Kupczyk

    2004-01-01

    In the paper the experimental results concerning the functional quality of thin, superhard coatings produced on cutting edges is described. Boron nitride coatings were deposited on insert cutting edges made cemented carbides by the pulse-plasma method. The comparative investigations of mentioned coatings have been concerned of tool life of edges during steel machining. In these investigations for the purpose of additional increase of coated edge durability an interfacial layers were applied. Presented investigations particularly pointed out to essential influence of the values of discharge voltage on the coating structure and durability of edges coated with boron nitride.

  13. Influence of the Discharge Voltage during Pulse-Plasma Process on the Durability of Edges coated with Superhard Coatings

    Institute of Scientific and Technical Information of China (English)

    MaciejKupczyk

    2004-01-01

    In the paper the experimental results concerning the functional quality of thin, superhard coatings produced on cutting edges is described. Boron nitride coatings were deposited on insert cutting edges made cemented carbides by the pulse-plasma method. The comparative investigations of mentioned coatings have been concerned of tool life of edges during steel machining. In these investigations for the purpose of additional increase of coated edge durability an interfacial layers were applied. Presented investigations particularly pointed out to essential influence of the values of discharge voltage on the coating structure and durability of edges coated with boron nitfide.

  14. High-speed, high-voltage pulse generation using avalanche transistor

    Science.gov (United States)

    Yong-sheng, Gou; Bai-yu, Liu; Yong-lin, Bai; Jun-jun, Qin; Xiao-hong, Bai; Bo, Wang; Bing-li, Zhu; Chuan-dong, Sun

    2016-05-01

    In this work, the conduction mechanism of avalanche transistors was demonstrated and the operation condition for generating high-speed pulse using avalanche transistors was illustrated. Based on the above analysis, a high-speed and high-voltage pulse (HHP) generating circuit using avalanche transistors was designed, and its working principle and process were studied. To improve the speed of the output pulse, an approach of reducing the rise time of the leading edge is proposed. Methods for selecting avalanche transistor and reducing the parasitic inductance and capacitance of printed circuit board (PCB) were demonstrated. With these instructions, a PCB with a tapered transmission line was carefully designed and manufactured. Output pulse with amplitude of 2 kV and rise time of about 200 ps was realized with this PCB mounted with avalanche transistors FMMT417, indicating the effectiveness of the HHP generating circuit design.

  15. High-voltage electrode optimization towards uniform surfacetreatment by a pulsed volume discharge

    OpenAIRE

    Ponomarev, A. V.; Pedos, M. S.; Scherbinin, S. V.; Mamontov, Y. I.; Ponomarev, Sergey Viktorovich

    2015-01-01

    In this study, the shape and material of the high-voltage electrode of an atmospheric pressure plasma generation system were optimised. The research was performed with the goal of achieving maximum uniformity of plasma treatment of the surface of the low-voltage electrode with a diameter of 100 mm. In order to generate low-temperature plasma with the volume of roughly 1 cubic decimetre, a pulsed volume discharge was used initiated with a corona discharge. The uniformity of the plasma in the r...

  16. Attaching single carbon nanotube on tip's apex using dielectrophoresis of DC-pulse voltage

    Institute of Scientific and Technical Information of China (English)

    Hee-Jin JEONG; Yoong-Ho JUNG; Deug-Woo LEE

    2009-01-01

    Single carbon nanotubes (CNTs) are candidates for a number of electronics and sensing applications, provided that single CNTs can be separated from a bundle of CNTs in suspension. Dielectrophoresis has recently been demonstrated as one route for the extraction of desired CNTs. However, previous methods using dielectrophoresis have found it difficult to extract single nanotubes from bundles of CNTs in solution. Here, we show that this restriction can be overcome by using pulsed DC voltage of an electric field, instead of regular AC and DC voltages.

  17. Simultaneously propagating voltage and pressure pulses in lipid monolayers of pork brain and synthetic lipids

    Science.gov (United States)

    Griesbauer, J.; Bössinger, S.; Wixforth, A.; Schneider, M. F.

    2012-12-01

    Hydrated interfaces are ubiquitous in biology and appear on all length scales from ions and individual molecules to membranes and cellular networks. In vivo, they comprise a high degree of self-organization and complex entanglement, which limits their experimental accessibility by smearing out the individual phenomenology. The Langmuir technique, however, allows the examination of defined interfaces, the controllable thermodynamic state of which enables one to explore the proper state diagrams. Here we demonstrate that voltage and pressure pulses simultaneously propagate along monolayers comprised of either native pork brain or synthetic lipids. The excitation of pulses is conducted by the application of small droplets of acetic acid and monitored subsequently employing time-resolved Wilhelmy plate and Kelvin probe measurements. The isothermal state diagrams of the monolayers for both lateral pressure and surface potential are experimentally recorded, enabling us to predict dynamic voltage pulse amplitudes of 0.1-3 mV based on the assumption of static mechanoelectrical coupling. We show that the underlying physics for such propagating pulses is the same for synthetic and natural extracted (pork brain) lipids and that the measured propagation velocities and pulse amplitudes depend on the compressibility of the interface. Given the ubiquitous presence of hydrated interfaces in biology, our experimental findings seem to support a fundamentally new mechanism for the propagation of signals and communication pathways in biology (signaling), which is based neither on protein-protein or receptor-ligand interaction nor diffusion.

  18. A High Voltage High Frequency Resonant Inverter for Supplying DBD Devices with Short Discharge Current Pulses

    OpenAIRE

    Bonnin, Xavier; Brandelero, Julio; Videau, Nicolas; Piquet, Hubert; Meynard, Thierry

    2014-01-01

    International audience; In this paper, the merits of a high-frequency resonant converter for supplying dielectric barrier discharges (DBD) devices are established. It is shown that, thanks to its high-frequency operating condition, such a converter allows to supply DBD devices with short discharge current pulses, a high repetition rate, and to control the injected power. In addition, such a topology eliminates the matter of connecting a high-voltage transformer directly across the DBD device ...

  19. Initial position estimation method for permanent magnet synchronous motor based on improved pulse voltage injection

    DEFF Research Database (Denmark)

    Wang, Z.; Lu, K.; Ye, Y.

    2011-01-01

    According to saliency of permanent magnet synchronous motor (PMSM), the information of rotor position is implied in performance of stator inductances due to the magnetic saturation effect. Researches focused on the initial rotor position estimation of PMSM by injecting modulated pulse voltage vec....... The experimental results show that the proposed method estimates the initial rotor position reliably and efficently. The method is also simple and can achieve satisfied estimation accuracy....

  20. Interconnected High-Voltage Pulsed-Power Converters System Design for H− Ion Sources

    CERN Document Server

    Aguglia, D

    2014-01-01

    This paper presents the design and experimental validations of a system of three new high-voltage (HV) pulsedpower converters for the H− sources. The system requires three pulsed voltages (50, 40, and 25 kV to ground) at 2-Hz repetition rate, for 700 μs of usable flat-top. The solution presents ripplefree output voltages and minimal stored energy to protect the ion source from the consequences of arc events. Experimental results on the final full-scale prototype are presented. In case of short-circuit events, the maximal energy delivered to the source is in the Joule range. HV flat-top stability of 1% is experimentally achieved with a simple Proportional-Integral- Derivative regulation and preliminary tuned H− source (e.g., radio frequency control, gas injection, and so forth). The system is running since more than a year with no power converter failures and damage to the source.

  1. Effect of Variation in Voltage on the Synthesis of Ag Nanopowder by Pulsed Wire Evaporation

    Directory of Open Access Journals (Sweden)

    Joon-Woo Song

    2012-01-01

    Full Text Available Nanosized Ag particles were obtained in liquid medium, which is composed of deionized water and sodium hexametaphosphate, using pulsed wire evaporation within hundreds of microseconds from pure initial Ag wire (99.98%, with varying voltage. Changes in powder morphology and microstructure due to change in supply voltage was observed by FE-SEM and HR-TEM, and phase structure of powders was analyzed by XRD. The results revealed that average particle size slightly increased with increasing supply voltage without any impurity and oxide phase, which was explained in terms of addition of stabilizer into the coolant liquid. The experimental results also suggest that addition of sodium hexametaphosphate into the coolant liquid is good for enhancing the dispersibility property of silver nanopowders.

  2. Development and Applications of discharges generated in liquids with short high voltage pulses

    Science.gov (United States)

    Kolb, Juergen; Miron, Camelia; Kruth, Angela; Balcerak, Michal; Bonislawski, Michal; Holub, Marcin

    2016-09-01

    Discharges that are generated within a liquid have been of scientific interest for more than a century. The possibility for a breakdown development that is not mediated by an initial gaseous phase is still disputed. In this respect are especially discharges that are instigated with short high voltage pulses calling for attention. Associated with this specific excitation scheme is a change in plasma development, plasma parameters and reaction mechanisms in the liquid. We have compared discharges in a point-to-plane geometry that were generated with 50-us or 10-ns high voltage pulses. Time-resolved shadowgraphy and spectroscopy were performed to evaluate discharge structures, plasma parameter and reactive species that were formed in distilled water or ethanol. Different propagation modes, with velocities of 6.7 km/s for tree-like streamers and only 50 m/s for bush-like streamers, were observed. Optical emission spectroscopy has shown the formation of molecular bands of nitrogen, as well as strongly broadened atomic hydrogen and oxygen, which are likely to be responsible for the observed surface modifications of polymers. With nanosecond high voltage pulses we found an increase of unsaturated bondings for polyimide surfaces that were exposed in the discharge volume.

  3. The study of surface wetting, nanobubbles and boundary slip with an applied voltage: A review

    Directory of Open Access Journals (Sweden)

    Yunlu Pan

    2014-07-01

    Full Text Available The drag of fluid flow at the solid–liquid interface in the micro/nanoscale is an important issue in micro/nanofluidic systems. Drag depends on the surface wetting, nanobubbles, surface charge and boundary slip. Some researchers have focused on the relationship between these interface properties. In this review, the influence of an applied voltage on the surface wettability, nanobubbles, surface charge density and slip length are discussed. The contact angle (CA and contact angle hysteresis (CAH of a droplet of deionized (DI water on a hydrophobic polystyrene (PS surface were measured with applied direct current (DC and alternating current (AC voltages. The nanobubbles in DI water and three kinds of saline solution on a PS surface were imaged when a voltage was applied. The influence of the surface charge density on the nanobubbles was analyzed. Then the slip length and the electrostatic force on the probe were measured on an octadecyltrichlorosilane (OTS surface with applied voltage. The influence of the surface charge on the boundary slip and drag of fluid flow has been discussed. Finally, the influence of the applied voltage on the surface wetting, nanobubbles, surface charge, boundary slip and the drag of liquid flow are summarized. With a smaller surface charge density which could be achieved by applying a voltage on the surface, larger and fewer nanobubbles, a larger slip length and a smaller drag of liquid flow could be found.

  4. Characteristics of titanium dioxide nanostructures synthesized via electrochemical anodization at different applied voltages

    Energy Technology Data Exchange (ETDEWEB)

    Cheong, Y. L.; Yam, F. K.; Hassan, Z. [Nano-Optoelectronics Research and Technology Laboratory School of Physics, Universiti Sains Malaysia, 11800 Penang (Malaysia)

    2015-05-15

    This paper presents the study of the growth of nanostructure titanium dioxide (TiO{sub 2}) via electrochemical anodization method. Both constant and alternating anodization voltage would be applied in this study. The effects of applied voltage on the morphological and structural properties were studied. Images of field emission scanning electron microscope (FE-SEM) revealed that morphology of nanostructure could be manipulated by changing the type and amount of applied voltage. Besides that, X-ray diffraction (XRD) results indicated that crystalline structures (anatase and rutile) could be obtained after being annealed at 700°C for 60 minutes. By analysing the data in XRD measurements, crystallite size of the TiO{sub 2} could be calculated by using the Scherrer method. Besides that, the relationship between mean crystallites sizes and anodization voltage would also be further studied in this paper.

  5. High-voltage nanosecond pulses in a low-pressure radiofrequency discharge

    CERN Document Server

    Pustylnik, Mikhail; Ivlev, Alexei; Vasilyak, Leonid; Couëdel, Lenaic; Thomas, Hubertus; Morfill, Gregor; Fortov, Vladimir

    2013-01-01

    An influence of a high-voltage (3-17 kV) 20 ns pulse on a weakly-ionized low-pressure (0.1-10 Pa) capacitively-coupled radiofrequency (RF) argon plasma is studied experimentally. The plasma evolution after pulse exhibits two characteristic regimes: a bright flash, occurring within 100 ns after the pulse (when the discharge emission increases by 2-3 orders of magnitude over the steady-state level), and a dark phase, lasting a few hundreds \\mu s (when the intensity of the discharge emission drops significantly below the steady-state level). The electron density increases during the flash and remains very large at the dark phase. 1D3V particle-in-cell simulations qualitatively reproduce both regimes and allow for detailed analysis of the underlying mechanisms. It is found that the high-voltage nanosecond pulse is capable of removing a significant fraction of plasma electrons out of the discharge gap, and that the flash is the result of the excitation of gas atoms, triggered by residual electrons accelerated in t...

  6. On the influence of high voltage slope steepness on breakdown and development of pulsed dielectric barrier discharges

    Science.gov (United States)

    Höft, H.; Becker, M. M.; Loffhagen, D.; Kettlitz, M.

    2016-12-01

    The influence of the steepness of the applied high voltage (HV) waveform on the characteristics of pulsed dielectric barrier discharges (DBDs) is investigated using a single-filament arrangement with 1 mm gap in 0.1 vol% O2 in N2 at atmospheric pressure. The slope steepness was varied between 75 V ns-1 and 200 V ns-1. The discharge development was recorded with a combined iCCD and streak camera system accompanied by electrical measurements. The analysis was supported by time-dependent, spatially one-dimensional fluid model calculations. A steeper HV slope leads to a higher transferred charge and electrical energy per cycle. The DBD emission structure in the gap features a shorter ‘dark space’ in front of the cathode for steeper HV pulses. The starting velocity of the positive streamer-like propagation at the rising slope of the HV pulses increases with increasing slope steepness, but without influencing the maximal velocity in front of the cathode. At the falling slope, however, smaller propagation velocities for steeper pulses were measured. The modelling results and the measurements of the emission during the pre-phase suggest that the elevated pre-ionisation and higher electrical energy for steeper HV slopes is responsible for most of the observed effects.

  7. Pulsed Plasma with Synchronous Boundary Voltage for Rapid Atomic Layer Etching

    Energy Technology Data Exchange (ETDEWEB)

    Economou, Demetre J.; Donnelly, Vincent M.

    2014-05-13

    Atomic Layer ETching (ALET) of a solid with monolayer precision is a critical requirement for advancing nanoscience and nanotechnology. Current plasma etching techniques do not have the level of control or damage-free nature that is needed for patterning delicate sub-20 nm structures. In addition, conventional ALET, based on pulsed gases with long reactant adsorption and purging steps, is very slow. In this work, novel pulsed plasma methods with synchronous substrate and/or “boundary electrode” bias were developed for highly selective, rapid ALET. Pulsed plasma and tailored bias voltage waveforms provided controlled ion energy and narrow energy spread, which are critical for highly selective and damage-free etching. The broad goal of the project was to investigate the plasma science and engineering that will lead to rapid ALET with monolayer precision. A combined experimental-simulation study was employed to achieve this goal.

  8. Frequency-Domain Maximum-Likelihood Estimation of High-Voltage Pulse Transformer Model Parameters

    CERN Document Server

    Aguglia, D

    2014-01-01

    This paper presents an offline frequency-domain nonlinear and stochastic identification method for equivalent model parameter estimation of high-voltage pulse transformers. Such kinds of transformers are widely used in the pulsed-power domain, and the difficulty in deriving pulsed-power converter optimal control strategies is directly linked to the accuracy of the equivalent circuit parameters. These components require models which take into account electric fields energies represented by stray capacitance in the equivalent circuit. These capacitive elements must be accurately identified, since they greatly influence the general converter performances. A nonlinear frequency-based identification method, based on maximum-likelihood estimation, is presented, and a sensitivity analysis of the best experimental test to be considered is carried out. The procedure takes into account magnetic saturation and skin effects occurring in the windings during the frequency tests. The presented method is validated by experim...

  9. Development of double-pulse lasers ablation system for generating gold ion source under applying an electric field

    Science.gov (United States)

    Khalil, A. A. I.

    2015-12-01

    Double-pulse lasers ablation (DPLA) technique was developed to generate gold (Au) ion source and produce high current under applying an electric potential in an argon ambient gas environment. Two Q-switched Nd:YAG lasers operating at 1064 and 266 nm wavelengths are combined in an unconventional orthogonal (crossed-beam) double-pulse configuration with 45° angle to focus on a gold target along with a spectrometer for spectral analysis of gold plasma. The properties of gold plasma produced under double-pulse lasers excitation were studied. The velocity distribution function (VDF) of the emitted plasma was studied using a dedicated Faraday-cup ion probe (FCIP) under argon gas discharge. The experimental parameters were optimized to attain the best signal to noise (S/N) ratio. The results depicted that the VDF and current signals depend on the discharge applied voltage, laser intensity, laser wavelength and ambient argon gas pressure. A seven-fold increases in the current signal by increasing the discharge applied voltage and ion velocity under applying double-pulse lasers field. The plasma parameters (electron temperature and density) were also studied and their dependence on the delay (times between the excitation laser pulse and the opening of camera shutter) was investigated as well. This study could provide significant reference data for the optimization and design of DPLA systems engaged in laser induced plasma deposition thin films and facing components diagnostics.

  10. High-voltage electrode optimization towards uniform surface treatment by a pulsed volume discharge

    Science.gov (United States)

    Ponomarev, A. V.; Pedos, M. S.; Scherbinin, S. V.; Mamontov, Y. I.; Ponomarev, S. V.

    2015-11-01

    In this study, the shape and material of the high-voltage electrode of an atmospheric pressure plasma generation system were optimised. The research was performed with the goal of achieving maximum uniformity of plasma treatment of the surface of the low-voltage electrode with a diameter of 100 mm. In order to generate low-temperature plasma with the volume of roughly 1 cubic decimetre, a pulsed volume discharge was used initiated with a corona discharge. The uniformity of the plasma in the region of the low-voltage electrode was assessed using a system for measuring the distribution of discharge current density. The system's low-voltage electrode - collector - was a disc of 100 mm in diameter, the conducting surface of which was divided into 64 radially located segments of equal surface area. The current at each segment was registered by a high-speed measuring system controlled by an ARM™-based 32-bit microcontroller. To facilitate the interpretation of results obtained, a computer program was developed to visualise the results. The program provides a 3D image of the current density distribution on the surface of the low-voltage electrode. Based on the results obtained an optimum shape for a high-voltage electrode was determined. Uniformity of the distribution of discharge current density in relation to distance between electrodes was studied. It was proven that the level of non-uniformity of current density distribution depends on the size of the gap between electrodes. Experiments indicated that it is advantageous to use graphite felt VGN-6 (Russian abbreviation) as the material of the high-voltage electrode's emitting surface.

  11. Effects of high voltage nanosecond pulsed plasma and micro DBD plasma on seed germination, growth development and physiological activities in spinach.

    Science.gov (United States)

    Ji, Sang-Hye; Choi, Ki-Hong; Pengkit, Anchalee; Im, Jun Sup; Kim, Ju Sung; Kim, Yong Hee; Park, Yeunsoo; Hong, Eun Jeong; Jung, Sun Kyung; Choi, Eun-Ha; Park, Gyungsoon

    2016-09-01

    In this study, we analyzed seed germination, seedling growth, and physiological aspects after treatment with high voltage nanosecond pulsed plasma and micro DBD plasma in spinach (Spinacia oleracea L.), a green leafy vegetable known to have low germination rate. Both germination and dry weight of seedlings increased after high voltage pulse shots were applied to spinach seeds. However seeds treated with many shots (10 shots) showed a decrease in germination rate and seedling growth. Seeds treated with air DBD plasma exhibited slightly higher germination and subsequent seedling growth than those treated with N2 plasma. Seed surface was degenerated after treated with high voltage pulsed plasma and micro DBD plasma but no significant difference in the degree of degeneration was observed among micro DBD plasma treatment time. Level of GA3 hormone and mRNA expression of an amylolytic enzyme-related gene in seeds were elevated 1 day after treatment with high voltage pulsed plasma. The relative amount of chlorophyll and total polyphenols in spinach seedlings grown from seeds treated with air DBD plasma was increased in 30 s, 1 min, and 3 min treatments. Taken together, our results suggest a possibility that plasma can enhance seed germination by triggering biochemical processes in seeds.

  12. All-optical detection of magnetization precession in tunnel junctions under applied voltage

    Science.gov (United States)

    Sasaki, Yuta; Suzuki, Kazuya; Sugihara, Atsushi; Kamimaki, Akira; Iihama, Satoshi; Ando, Yasuo; Mizukami, Shigemi

    2017-02-01

    An all-optical time-resolved magneto-optical Kerr effect measurement of a micron-sized tunnel junction with a CoFeB electrode was performed. The femtosecond (fs) laser-induced magnetization precession was clearly observed at various magnetic field angles. The frequency f and relaxation time τ of the magnetization precession varied with the voltage applied via a MgO barrier. The precession dynamics were in accordance with Kittel’s ferromagnetic resonance mode, and the voltage-induced changes in f and τ were well explained by the voltage-induced change in the perpendicular magnetic anisotropy of -36 fJ/Vm.

  13. Analysis of a modular generator for high-voltage, high-frequency pulsed applications, using low voltage semiconductors (series connected step-up (1:10) transformers

    Science.gov (United States)

    Redondo, L. M.; Fernando Silva, J.; Margato, E.

    2007-03-01

    This article discusses the operation of a modular generator topology, which has been developed for high-frequency (kHz), high-voltage (kV) pulsed applications. The proposed generator uses individual modules, each one consisting of a pulse circuit based on a modified forward converter, which takes advantage of the required low duty cycle to operate with a low voltage clamp reset circuit for the step-up transformer. This reduces the maximum voltage on the semiconductor devices of both primary and secondary transformer sides. The secondary winding of each step-up transformer is series connected, delivering a fraction of the total voltage. Each individual pulsed module is supplied via an isolation transformer. The assembled modular laboratorial prototype, with three 5kV modules, 800V semiconductor switches, and 1:10 step-up transformers, has 80% efficiency, and is capable of delivering, into resistive loads, -15kV/1A pulses with 5μs width, 10kHz repetition rate, with less than 1μs pulse rise time. Experimental results for resistive loads are presented and discussed.

  14. Analysis of a modular generator for high-voltage, high-frequency pulsed applications, using low voltage semiconductors (series connected step-up (1:10) transformers.

    Science.gov (United States)

    Redondo, L M; Fernando Silva, J; Margato, E

    2007-03-01

    This article discusses the operation of a modular generator topology, which has been developed for high-frequency (kHz), high-voltage (kV) pulsed applications. The proposed generator uses individual modules, each one consisting of a pulse circuit based on a modified forward converter, which takes advantage of the required low duty cycle to operate with a low voltage clamp reset circuit for the step-up transformer. This reduces the maximum voltage on the semiconductor devices of both primary and secondary transformer sides. The secondary winding of each step-up transformer is series connected, delivering a fraction of the total voltage. Each individual pulsed module is supplied via an isolation transformer. The assembled modular laboratorial prototype, with three 5 kV modules, 800 V semiconductor switches, and 1:10 step-up transformers, has 80% efficiency, and is capable of delivering, into resistive loads, -15 kV1 A pulses with 5 micros width, 10 kHz repetition rate, with less than 1 micros pulse rise time. Experimental results for resistive loads are presented and discussed.

  15. Effect of a longitudinally applied voltage upon the growth of Zea mays seedlings

    Science.gov (United States)

    Desrosiers, M. F.; Bandurski, R. S.

    1988-01-01

    The electrical parameters that affect young seedling growth were investigated. Voltages ranging from 5 to 40 volts were applied longitudinally along the mesocotyl region of 4-day old Zea mays L. (cv Silver Queen) seedlings for periods of 3 or 4 hours. It was determined that: (a) making the tips of the seedlings electrically positive relative to the base strongly inhibited shoot growth at 5 volts, whereas the reverse polarity had no effect; (b) at higher voltages, making the tip of the seedlings negative caused less growth inhibition than the reverse polarity at each voltage level; (c) the higher the applied voltage the greater the degree of inhibition; and, (d) the more growth inhibition experienced by the plants the poorer, and slower, their recovery. Previous observations of a relationship between the amount of free indole-3-acetic acid in the mesocotyl cortex and the growth rate of the mesocotyl and of gravitropism-induced movement of labeled indole-3-acetic acid from the seed to the shoot lead to the prediction of a voltage-dependent gating of the movement of indole-3-acetic acid from the stele to the cortex. This provided the basis for attempting to alter the growth rate of seedlings by means of an applied voltage.

  16. A new method for compensation of the effect of charging transformer's leakage inductance on PFN voltage regulation in Klystron pulse modulators

    Science.gov (United States)

    Patel, Akhil; Kale, Umesh; Shrivastava, Purushottam

    2017-04-01

    The Line type modulators have been widely used to generate high voltage rectangular pulses to power the klystron for high power RF generation. In Line type modulator, the Pulse Forming Network (PFN) which is a cascade combination of lumped capacitors and inductors is used to store the electrical energy. The charged PFN is then discharged into a klystron by firing a high voltage Thyratron switch. This discharge generates a high voltage rectangular pulse across the klystron electrodes. The amplitude and phase of Klystron's RF output is governed by the high voltage pulse amplitude. The undesired RF amplitude and phase stability issues arises at the klystron's output due to inter-pulse and during the pulse amplitude variations. To reduce inter-pulse voltage variations, the PFN is required to be charged at the same voltage after every discharge cycle. At present, the combination of widely used resonant charging and deQing method is used to regulate the pulse to pulse PFN voltage variations but the charging transformer's leakage inductance puts an upper bound on the regulation achievable by this method. Here we have developed few insights of the deQing process and devised a new compensation method to compensate this undesired effect of charging transformer's leakage inductance on the pulse to pulse PFN voltage stability. This compensation is accomplished by the controlled partial discharging of the split PFN capacitor using a low voltage MOSFET switch. Theoretically, very high values of pulse to pulse voltage stability may be achieved using this method. This method may be used in deQing based existing modulators or in new modulators, to increase the pulse to pulse voltage stability, without having a very tight bound on charging transformer's leakage inductance. Given a stable charging power supply, this method may be used to further enhance the inter-pulse voltage stability of modulators which employ the direct charging, after replacing the direct charging with the

  17. Characterization of a pulsed mode high voltage power supply for nuclear detectors

    Science.gov (United States)

    Ghazali, A. B.; Ahmad, T. S.; Abdullah, N. A.

    2013-06-01

    This paper discusses the characterization of a pulsed mode high voltage power supply (HVPS) using LT1073 chip. The pulsed modulated signal generated from this chip is amplified using a step-up ferrite core transformer of 1:20 turn ratio and then further multiplied and converted into DC high voltage output using a diode-capacitor arrangement. The circuit is powered by a 9V alkaline battery but regulated at 5V supply. It was found that the output for this setup is 520V, 87 μA with 10% load regulation. This output is suitable to operate a pancake-type GM detector, typically model LND 7317 where the plateau is from 475V to 675V. It was also found that when a β-source with intensity of 120 cps is used, the power consumption of the circuit is 5 V, 10.1 mA only. When the battery was left 'on' for 40 hours continuously, the battery's voltage has dropped to 6.9V, meaning that the 5V supply as well as 520V output is still maintained. It is noted that the minimum output voltage of 475V has reached when the regulated supply has reduced to 4.6V and consequently the 9V battery dropped to 6.5V, and this had happened after approximately 3 days of continuous operation. The power efficiency for this circuitry was found to be 89.5%. This result has far better in performance since the commercial portable equipment of this type has normally specified that not less than 8 hours continuous operation only. On the circuit design for this power supply, it was found that the enveloped frequency is 133 Hz with approximately 50% duty cycle. The modulated frequency during 'on' state was found to be 256 KHz in which the majority of power consumption is required.

  18. Note: Compact high voltage pulse transformer made using a capacitor bank assembled in the shape of primary.

    Science.gov (United States)

    Shukla, Rohit; Banerjee, Partha; Sharma, Surender K; Das, Rashmita; Deb, Pankaj; Prabaharan, T; Das, Basanta; Adhikary, Biswajit; Verma, Rishi; Shyam, Anurag

    2011-10-01

    The experimental results of an air-core pulse transformer are presented, which is very compact (transformer. A high voltage capacitor assembly (pulse-forming-line capacitor, PFL) of 5.1 nF is connected with the secondary of transformer. The transformer output voltage is 160 kV in its second peak appearing in less than 2 μS from the beginning of the capacitor discharge. The primary capacitor bank can be charged up to a maximum of 18 kV, with the voltage delivery of 360 kV in similar capacitive loads.

  19. Different approach to pulsed high-voltage vacuum-insulation design

    Directory of Open Access Journals (Sweden)

    John G. Leopold

    2007-06-01

    Full Text Available A theoretical methodology promising improved design of vacuum insulation in high-voltage pulsed-power systems is described. It consists of shaping the electromagnetic fields within the system in such a way that charged particles which can in principle initiate vacuum surface breakdown are deflected away from the insulator surface, and secondary electrons, if emitted, are prevented from restriking the surface. Thus, vacuum surface breakdown is prevented before it is able to develop. Our methodology is presented here by a set of case studies.

  20. Voltage measurements at the vacuum post-hole convolute of the Z pulsed-power accelerator

    Directory of Open Access Journals (Sweden)

    E. M. Waisman

    2014-12-01

    Full Text Available Presented are voltage measurements taken near the load region on the Z pulsed-power accelerator using an inductive voltage monitor (IVM. Specifically, the IVM was connected to, and thus monitored the voltage at, the bottom level of the accelerator’s vacuum double post-hole convolute. Additional voltage and current measurements were taken at the accelerator’s vacuum-insulator stack (at a radius of 1.6 m by using standard D-dot and B-dot probes, respectively. During postprocessing, the measurements taken at the stack were translated to the location of the IVM measurements by using a lossless propagation model of the Z accelerator’s magnetically insulated transmission lines (MITLs and a lumped inductor model of the vacuum post-hole convolute. Across a wide variety of experiments conducted on the Z accelerator, the voltage histories obtained from the IVM and the lossless propagation technique agree well in overall shape and magnitude. However, large-amplitude, high-frequency oscillations are more pronounced in the IVM records. It is unclear whether these larger oscillations represent true voltage oscillations at the convolute or if they are due to noise pickup and/or transit-time effects and other resonant modes in the IVM. Results using a transit-time-correction technique and Fourier analysis support the latter. Regardless of which interpretation is correct, both true voltage oscillations and the excitement of resonant modes could be the result of transient electrical breakdowns in the post-hole convolute, though more information is required to determine definitively if such breakdowns occurred. Despite the larger oscillations in the IVM records, the general agreement found between the lossless propagation results and the results of the IVM shows that large voltages are transmitted efficiently through the MITLs on Z. These results are complementary to previous studies [R. D. McBride et al., Phys. Rev. ST Accel. Beams 13, 120401 (2010

  1. Applied-voltage dependence on conductometric track etching of poly(vinylidene fluoride) films

    Energy Technology Data Exchange (ETDEWEB)

    Nuryanthi, N. [Department of Nuclear Engineering and Management, School of Engineering, The University of Tokyo, 7-3-1 Hongo, Bunkyo-ku, Tokyo 113-8656 (Japan); Quantum Beam Science Directorate, Japan Atomic Energy Agency, 1233 Watanuki, Takasaki, Gunma 370-1292 (Japan); Yamaki, T., E-mail: yamaki.tetsuya@jaea.go.jp [Quantum Beam Science Directorate, Japan Atomic Energy Agency, 1233 Watanuki, Takasaki, Gunma 370-1292 (Japan); Koshikawa, H.; Asano, M.; Sawada, S.; Hasegawa, S.; Maekawa, Y. [Quantum Beam Science Directorate, Japan Atomic Energy Agency, 1233 Watanuki, Takasaki, Gunma 370-1292 (Japan); Katsumura, Y. [Department of Nuclear Engineering and Management, School of Engineering, The University of Tokyo, 7-3-1 Hongo, Bunkyo-ku, Tokyo 113-8656 (Japan)

    2013-11-01

    We investigated the conductometric etching of heavy-ion-irradiated poly(vinylidene fluoride) (PVDF) films to study their pore growth behavior, which was estimated from radial etch rates under the application of different voltages. The plateau of the pore diameter seen in a bulk etching region was constant at an applied voltage ranging from 0.1 to 3.0 V, while the breakthrough time varied considerably. Employing the first derivative of the conductometric curve, corresponding to the radial etch rate, R, enabled us to clearly analyze parameters reflecting the track structures (i.e., the maximum radial etch rate, R{sub max}, and the time for the diameter to reach the final plateau, T{sub E}). Interestingly, these two parameters were significantly influenced by the applied voltage. There was a trend toward increasing values of R{sub max} and, in contrast, decreasing levels of T{sub E} as the applied voltage was increased. These promotional effects of the etching process can be rationalized by considering the electrophoretic migration of dissolved species in and out of each pore. Thus, conductometric etching under different voltage conditions offers the ability to control pore geometries by optimizing the etching process in the transverse direction as well as in the thickness direction.

  2. High voltage pulsed current in collagen realignment, synthesis, and angiogenesis after Achilles tendon partial rupture

    Directory of Open Access Journals (Sweden)

    Érika P. Rampazo

    2016-01-01

    Full Text Available ABSTRACT Objective To verify the efficacy of high voltage pulsed current in collagen realignment and synthesis and in angiogenesis after the partial rupturing of the Achilles tendon in rats. Method Forty male Wistar rats were randomized into four groups of 10 animals each: sham, cathodic stimulation, anodic stimulation, and alternating stimulation. Their Achilles tendons were submitted to direct trauma by a free-falling metal bar. Then, the treatment was administered for six consecutive days after the injury. In the simulation group, the electrodes were positioned on the animal, but the device remained off for 30 minutes. The other groups used a frequency of 120 pps, sensory threshold, and the corresponding polarity. On the seventh day, the tendons were removed and sent for histological slide preparation for birefringence and Picrosirius Red analysis and for blood vessel quantification. Results No significant difference was observed among the groups regarding collagen realignment (types I or III collagen or quantity of blood vessels. Conclusion High voltage pulsed current for six consecutive days was not effective in collagen realignment, synthesis, or angiogenesis after the partial rupturing of the Achilles tendon in rats.

  3. High voltage pulsed current in collagen realignment, synthesis, and angiogenesis after Achilles tendon partial rupture

    Science.gov (United States)

    Rampazo, Érika P.; Liebano, Richard E.; Pinfildi, Carlos Eduardo; Folha, Roberta A. C.; Ferreira, Lydia M.

    2016-01-01

    ABSTRACT Objective To verify the efficacy of high voltage pulsed current in collagen realignment and synthesis and in angiogenesis after the partial rupturing of the Achilles tendon in rats. Method Forty male Wistar rats were randomized into four groups of 10 animals each: sham, cathodic stimulation, anodic stimulation, and alternating stimulation. Their Achilles tendons were submitted to direct trauma by a free-falling metal bar. Then, the treatment was administered for six consecutive days after the injury. In the simulation group, the electrodes were positioned on the animal, but the device remained off for 30 minutes. The other groups used a frequency of 120 pps, sensory threshold, and the corresponding polarity. On the seventh day, the tendons were removed and sent for histological slide preparation for birefringence and Picrosirius Red analysis and for blood vessel quantification. Results No significant difference was observed among the groups regarding collagen realignment (types I or III collagen) or quantity of blood vessels. Conclusion High voltage pulsed current for six consecutive days was not effective in collagen realignment, synthesis, or angiogenesis after the partial rupturing of the Achilles tendon in rats. PMID:27556387

  4. Pulsed Current-Voltage-Induced Perturbations of a Premixed Propane/Air Flame

    Directory of Open Access Journals (Sweden)

    Jacob. B. Schmidt

    2011-01-01

    Full Text Available The effect of millisecond wide sub-breakdown pulsed voltage-current induced flow perturbation has been measured in premixed laminar atmospheric pressure propane/air flame. The flame equivalence ratios were varied from 0.8 to 1.2 with the flow speeds near 1.1 meter/second. Spatio-temporal flame structure changes were observed through collection of CH (A-X and OH (A-X chemiluminescence and simultaneous spontaneous Raman scattering from N2. This optical collection scheme allows us to obtain a strong correlation between the measured gas temperature and the chemiluminescence intensity, verifying that chemiluminescence images provide accurate measurements of flame reaction zone structure modifications. The experimental results suggest that the flame perturbation is caused by ionic wind originating only from the radial positive space-charge distribution in/near the cathode fall. A net momentum transfer acts along the annular space discharge distribution in the reaction zone at or near the cathode fall which modifies the flow field near the cathodic burner head. This radially inward directed body force appears to enhance mixing similar to a swirl induced modification of the flame structure. The flame fluidic response exhibit a strong dependence on the voltage pulse width ≤10 millisecond.

  5. Transcranial low voltage pulsed electromagnetic fields in patients with treatment-resistant depression

    DEFF Research Database (Denmark)

    Martiny, Klaus Per Juul; Lunde, Marianne; Bech, Per

    2010-01-01

    of a new principle using low-intensity transcranially applied pulsed electromagnetic fields (T-PEMF) in combination with antidepressants in patients with treatment-resistant depression. METHODS: This was a sham-controlled double-blind study comparing 5 weeks of active or sham T-PEMF in patients...

  6. Condition for the occurrence of phase slip centers in superconducting nanowires under applied current or voltage

    DEFF Research Database (Denmark)

    Michotte, S.; Mátéfi-Tempfli, Stefan; Piraux, L.;

    2004-01-01

    Experimental results on the phase slip process in superconducting lead nanowires are presented under two different experimental conditions: constant applied current or constant voltage. Based on these experiments we established a simple model which gives us the condition of the appearance of phas...

  7. The Study of Active Atoms in High-Voltage Pulsed Coronal Discharge by Optical Diagnostics

    Institute of Scientific and Technical Information of China (English)

    Liu Feng; Wang Wenchun; Wang Su; Ren Chunsheng; Wang Younian

    2005-01-01

    In this study, the emission spectra of active atoms O (3p5P → 3s5S20 777.4 nm),Ha (3P → 2S 656.3 nm) and N (3p4P → 3s4S0 742.3 nm, 744.2 nm, 746.8 nm) produced by thepositive high-voltage pulsed corona discharge (HVPCD) of N2 and H2O mixture in a needle-platereactor have successfully been recorded against a severe electromagnetic interference coming fromthe HVPCD at one atmosphere. The effects of the peak voltage, the repetition rate of pulseddischarge and the flow rate of oxygen on the production of those active atoms are investigated. Itis found that when the peak voltage and the repetition rate of the pulsed discharge are increased,the emission intensities of those active atoms rise correspondingly. And the emission intensities ofO (3p5P → 3s5S20 777.4 nm), Ha (3P → 2S 656.3 nm) and N (3p4P → 3s4S0 742.3 nm, 744.2 nm,746.8 nm) increase with the flow rate of oxygen (from 0 to 25 ml/min) and achieve a maximumvalue at a flow rate of 25 ml/min. When the flow rate of oxygen is increased further, the emissionintensities of those atoms visibly decrease correspondingly. The main physicochemical processesof interaction involved between electrons, neutrals and ions are also discussed.

  8. Efficiency of high- and low-voltage pulse combinations for gene electrotransfer in muscle, liver, tumor, and skin

    DEFF Research Database (Denmark)

    André, F M; Gehl, J; Sersa, G;

    2008-01-01

    Gene electrotransfer is gaining momentum as an efficient methodology for nonviral gene transfer. In skeletal muscle, data suggest that electric pulses play two roles: structurally permeabilizing the muscle fibers and electrophoretically supporting the migration of DNA toward or across......, but not to liver; and (4) efficient gene electrotransfer was achieved with HV field strengths below the detectability thresholds for permeabilization; and (5) the lag time interval between the HV and LV pulses decreased sensitivity to the HV pulses, enabling a wider HV amplitude range. In conclusion, HV plus LV...... the permeabilized membrane. To investigate this further, combinations of permeabilizing short high-voltage pulses (HV; hundreds of V/cm) and mainly electrophoretic long low-voltage pulses (LV; tens of V/cm) were investigated in muscle, liver, tumor, and skin in rodent models. The following observations were made...

  9. A pulsed-power generator merging inductive voltage and current adders and its switch trigger application example.

    Science.gov (United States)

    Li, Lee; Yafeng, Ge; Heqin, Zhong; Bin, Yu; Longjun, Xie

    2013-07-01

    A pulsed-power generator using inductive adder technology is proposed for the case of a discharge gap. The merit of this generator is to merge the pulsed-voltage and pulsed-current adders via the dual secondary windings with special circuit. For the nonlinear impedance in any discharge gap, the standalone voltage-pulse and current-pulse can be outputted successively by this generator. The proposed generator is especially useful for the common resolution of implementing pulse discharge at less cost. As an application example, a compact trigger prototype was developed to compatibly use in the gas-insulated and vacuum switches. Experiments achieved good results that the triggered switches showed stable performance and long life. If the basic circuit of this proposed generator is regarded as a pulsed-generating unit, a certain number of such units connected in parallel can be expected to form a general device with generating greater breakdown-voltage and sustained-current pulses for discharge gaps.

  10. Spatial and Excitation Variations for Different Applied Voltages in an Atmospheric Neon Plasma Jet

    Science.gov (United States)

    Yang, Lanlan; Tu, Yan; Yu, Yongbo; Hu, Dinglan; Zhang, Xiong

    2016-09-01

    A neon plasma jet was generated in air, driven by a 9 kHz sinusoidal power supply. The characteristics of the plasma plume and the optical spectra with plasma propagation for different applied voltages were investigated. By increasing the applied voltage, the plasma plume first increases and then retracts to become short and bulky. The shortened effect of Ne plasma plume (about 10 mm) for the further voltage increasing is more apparent than that of He (about 3 mm) and Ar (about 1 mm). Emission intensity of the N2 (337 nm) increases with the applied voltage, gradually substituting the emission intensity of Ne (702 nm and 585 nm) as the noticeable radiation. At the nozzle opening, the Ne (702 nm) emission dominates, while the Ne (585 nm) emission is most noticeable around the tip of the plasma plume. The spatial distribution of the three spectral lines indicates that Ne (702 nm) emission decreases dramatically with plasma propagation while Ne (585 nm) and N2 (337 nm) emissions reach their maxima at the middle of the plasma plume. The results indicate that the Ne (702 nm) emission is much more sensitive to the average electron temperature and the density of the high-energy electrons, so it changes greatly at the tube nozzle and little at the tip region as the voltage increases. The population of high-energy electrons, the average electron temperature, the collision with air molecules and the Penning effect between Ne metastables and air molecules may explain their different variations with plasma propagating and voltage increasing. supported by National Natural Science Fundation of China (No. 61271053), the Natural Science Foundation of Jiangsu Province of China (No. BK2012737), the Foundation for Excellent Youth Scholars of Southeast University, China

  11. Design and simulation of the space vector modulation and applied to a load RL powered by a voltage inverter

    Directory of Open Access Journals (Sweden)

    Marouane El Azzaoui

    2016-07-01

    Full Text Available The vector control performance applied to rotating machines depends largely on static and dynamic characteristics of the inverter associated with it. The development of the pulse-width modulation (PWM provided greater flexibility in the control of the converters. The objective of this work is to construct a simplified and practical space vector modulation (SVM based on the selection of the sequence and the calculation of the conduction time or extinction. We have presented the blocks of the simulation vector modulation on the Matlab / Simulink with a new method for determining conduction time and analyzed its application on a load RL supplied by a voltage inverter. The performance of the proposed method has been presented by the simulation results.

  12. Investigation of the effects caused by applying voltage in Layer-by-Layer self-assembly method

    Directory of Open Access Journals (Sweden)

    Omura Y.

    2013-08-01

    Full Text Available Recently, Layer-by-Layer (LbL self-assembly method under applied voltage (voltage-applied LbL attracts great attention. It is reported that the method enables more abundant film adsorption than conventional LbL method. However, a small proportion of experimental results about adsorption of polyelectrolytes by voltage-applied LbL have been reported. In this study, voltage-applied LbL method using weakly charged polyelectrolytes was examined. Poly (allylamine hydrochloride (PAH and Poly (ethylene imine (PEI as cationic solutions and Poly (acrylic acid (PAA as anionic solution were chosen. The pH of solutions was adjusted to several conditions and film of PAH/PAA and film of PEI/PAA were fabricated by voltage-applied LbL method. Change of adsorption behavior and film morphology by applying voltage depended on pH condition of solutions. When pH of PAH/PAA solutions was 3.9/3.8, respectively, the film adsorption was accelerated by applying voltage. Moreover, in this condition, the surface morphology remarkably changes and texture structure appears by applying voltage. Consequently, it was found that applying voltage in LbL method was effective in controlling film adsorption and the surface nano structure.

  13. [Degradation of 4-chlorophenol in aqueous solution by high-voltage pulsed discharge-ozone technology].

    Science.gov (United States)

    Wen, Yuezhong; Jiang, Xuanzhen; Liu, Weiping

    2002-03-01

    The combination of high voltage pulse discharge and ozonation as an advanced oxidation technology was used to investigate the degradation of 4-chlorophenol (4-CP) in water. The factors that affect the rate of degradation were discussed. The 1.95 x 10(-3) mol/L solutions of 4-CP were almost completely (96%) degraded after the discharge treatment of 30 min. The degradation of 4-CP was investigated as a function of the ozone concentration, radical scavenger and electrode distance. The rate of 4-CP degradation increases with an increase in ozone concentration and a decrease in the electrode distance from 20 mm to 10 mm. The presence of radical scavenger decreased the rate of 4-CP degradation.

  14. An exploding foil shockwave technique for magnetic flux compression and high voltage pulse generation

    CERN Document Server

    Goh, S E

    2002-01-01

    This thesis describes a novel electromagnetic shockwave technique for use in compressing magnetic flux and to serve as the basis for a new approach to producing fast-rising voltage pulses with amplitudes of several hundred kV. The shockwave is produced by an exploding foil driven electric gun that accelerates a Mylar flyer to impact with a sample of aluminium powder. Both Japanese and Russian researchers have previously published experimental results for shockwave magnetic flux compression using an explosive driver. The present research considers replacing the explosive energy of this driver by the electrostatic energy stored in a capacitor bank, thereby enabling experiments to be performed in a laboratory environment. Differences in performance that arise from the use of explosive and electrical driver are examined. A conventional electric gun system in planar geometry is developed to study the insulator-to-metallic transition in shock-compressed aluminium powder. This provides data on the conducting shock f...

  15. Pretreatment of food waste with high voltage pulse discharge towards methane production enhancement.

    Science.gov (United States)

    Zou, Lianpei; Ma, Chaonan; Liu, Jianyong; Li, Mingfei; Ye, Min; Qian, Guangren

    2016-12-01

    Anaerobic batch tests were performed to investigate the methane production enhancement and solid transformation rates from food waste (FW) by high voltage pulse discharge (HVPD) pretreatment. The total cumulative methane production with HVPD pretreatment was 134% higher than that of the control. The final volatile solids transformation rates of FW with and without HVPD pretreatment were 54.3% and 32.3%, respectively. Comparison study on HVPD pretreatment with acid, alkali and ultrasonic pretreatments showed that the methane production and COD removal rates of FW pretreated with HVPD were more than 100% higher than the control, but only about 50% higher can be obtained with other pretreatments. HVPD pretreatment could be a promising pretreatment method in the application of energy recovery from FW.

  16. Effects of the Liquid Conductivity on Pulsed High-voltage Discharge Modes in Water

    Institute of Scientific and Technical Information of China (English)

    Bin YANG; Le Cheng LEI; Ming Hua ZHOU

    2004-01-01

    Spark, stream and corona pulsed high-voltage discharges in water induced by the various initial conductivities have been examined in this paper. The discharge modes changed from spark to corona discharge with the liquid conductivity increasing. The apparent production of OH radical and quantum yield generated by spark discharge in distilled water were 11.57 μmol/L and 0.0978photon/s, respectively. A preliminary study on acid fuchsine (AF) treatment indicated that higher AF removal efficiency has been achieved by spark discharge. The process of degradation showed that the oxidative effects through OH radical oxidation did not play an important role and did increase with the discharge mode changing to spark discharge.

  17. High voltage bulk GaN-based photoconductive switches for pulsed power applications

    Science.gov (United States)

    Leach, J. H.; Metzger, R.; Preble, E. A.; Evans, K. R.

    2013-03-01

    Switches are at the heart of all pulsed power and directed energy systems, which find utility in a number of applications. At present, those applications requiring the highest power levels tend to employ spark-gap switches, but these suffer from relatively high delay-times (~10-8 sec), significant jitter (variation in delay time), and large size. That said, optically-triggered GaN-based photoconductive semiconductor switches (PCSS) offer a suitably small form factor and are a cost-effective, versatile solution in which delay times and jitter can be extremely short. Furthermore, the optical control of the switch means that they are electrically isolated from the environment and from any other system circuitry, making them immune from electrical noise, eliminating the potential for inadvertent switch triggering. Our recent work shows great promise to extend high-voltage GaN-based extrinsic PCSS state-of-the-art performance in terms of subnanosecond response times, low on-resistance, high current carrying capacity and high blocking voltages. We discuss our recent results in this work.

  18. Numerical simulation of high voltage electric pulse comminution of phosphate ore

    Institute of Scientific and Technical Information of China (English)

    Razavian Seyed Mohammad; Rezai Bahram; Irannajad Mehdi; Ravanji Mohammad Hasan

    2015-01-01

    Numerical simulation of the electrical field distribution helps in-depth understanding of the mechanisms behind the responses and the benefits of the high voltage pulse comminution. The COMSOL Multiphysics package was used to numerically simulate the effect of ore compositions in this study. Regarding phos-phate ore particles shape and composition, the effects of mineral composition, particle size, particle shape and electrodes distance were investigated on the electrical field intensity and distribution. The results show that the induced electrical field is significantly dependent on the electrical properties of minerals, the feed particle size and the location of conductive minerals in ores. The angle of material contact sur-face with the discharge electrode is also an important factor in the intensity of electrical field. Moreover, it is found that the specific liberation effect at the disintegration of phosphate ore by electrical pulses is due to the locality of the electrical field at the interface of mineral components of the phosphate ore aggregates with different permittivities. However, the intensity of the electrical field increases with shar-pening the contact angle. Besides, the electrical discharge in the samples is converted to the elec-trohydraulic discharge across the surrounding water by changing the distance between the discharge electrode and sample surface.

  19. Dual branch high voltage pulse generator for the beam extraction of the Large Hadron Collider

    CERN Document Server

    Bonthond, J; Ducimetière, L; Jansson, U; Vossenberg, Eugène B

    2002-01-01

    The LHC beam extraction kicker system, MKD, is composed of 15 fast kicker magnets per beam to extract the particles in one turn from the collider and to dispose them, after dilution, on an external absorber. Each magnet is powered by a separate pulse generator. The original single branch generator consisted of a discharge capacitor in series with a solid state closing switch left bracket 1 right bracket operating at 30 kV. In combination with a parallel freewheel diode stack this generator produced a current pulse of 2.7 mus rise time, 18.5 kA amplitude and about 1.8 ms fall time, of which only about 90 mus are needed to dump the beam. The freewheel diode circuit is equipped with a flat top current droop compensation network, consisting of a low voltage, low stray inductance, high current discharge capacitor. Extensive reliability studies have meanwhile suggested to further increase the operational safety of this crucial system by equipping each generator with two parallel branches. This paper presents the re...

  20. A Xenon dielectric barrier discharge lamp (172nm) with a fast-pulse voltage driver: Influence of the voltage waveform on plasma kinetic issues and light output.

    Science.gov (United States)

    Carman, Robert; Ward, Barry; Mildren, Richard; Kane, Deborah

    2003-10-01

    An important class of vacuum-ultraviolet (VUV) excimer lamps based on high pressure rare-gas and rare-gas halogen mixtures utilize the dielectric barrier discharge (DBD) to generate a transient, non-equilibrium plasma that yields high electrical to VUV conversion efficiency. Recent interest has focussed on the use of pulsed voltage excitation techniques (rather than conventional AC sinusoidal waveforms) to alter the physical appearance of the DBD "micro-discharges" from filamentary (AC) to semi-diffuse, conical or homogeneous (pulsed), whilst at the same time dramatically improving the lamp performance and VUV efficiency^1,2. We report results from a combined experimental/computer modelling study of a short-pulse excited co-axial DBD Xe lamp to investigate the influence of the pulsed voltage waveform on the discharge structure, lamp performance, VUV output, and electrical efficiency. The underlying plasma kinetics issues relating to lamp performance, including parasitic collisional processes that act to quench key xenon species population densities, are examined in detail. ^1 Vollkommer F and Hitzschke, US patent 5604410 (1997) ^2 R.P.Mildren and R.J.Carman, J.Phys.D, 34, L1-L6 (2001)

  1. Characteristics of temperature rise in variable inductor employing magnetorheological fluid driven by a high-frequency pulsed voltage source

    Science.gov (United States)

    Lee, Ho-Young; Kang, In Man; Shon, Chae-Hwa; Lee, Se-Hee

    2015-05-01

    A variable inductor with magnetorheological (MR) fluid has been successfully applied to power electronics applications; however, its thermal characteristics have not been investigated. To evaluate the performance of the variable inductor with respect to temperature, we measured the characteristics of temperature rise and developed a numerical analysis technique. The characteristics of temperature rise were determined experimentally and verified numerically by adopting a multiphysics analysis technique. In order to accurately estimate the temperature distribution in a variable inductor with an MR fluid-gap, the thermal solver should import the heat source from the electromagnetic solver to solve the eddy current problem. To improve accuracy, the B-H curves of the MR fluid under operating temperature were obtained using the magnetic property measurement system. In addition, the Steinmetz equation was applied to evaluate the core loss in a ferrite core. The predicted temperature rise for a variable inductor showed good agreement with the experimental data and the developed numerical technique can be employed to design a variable inductor with a high-frequency pulsed voltage source.

  2. Characteristics of temperature rise in variable inductor employing magnetorheological fluid driven by a high-frequency pulsed voltage source

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Ho-Young; Kang, In Man, E-mail: imkang@ee.knu.ac.kr [School of Electronics Engineering, Kyungpook National University, Daegu 702-701 (Korea, Republic of); Shon, Chae-Hwa [Korea Electrotechnology Research Institute, Changwon 642-120 (Korea, Republic of); Lee, Se-Hee, E-mail: shlees@knu.ac.kr [Department of Electrical Engineering, Kyungpook National University, Daegu 702-701 (Korea, Republic of)

    2015-05-07

    A variable inductor with magnetorheological (MR) fluid has been successfully applied to power electronics applications; however, its thermal characteristics have not been investigated. To evaluate the performance of the variable inductor with respect to temperature, we measured the characteristics of temperature rise and developed a numerical analysis technique. The characteristics of temperature rise were determined experimentally and verified numerically by adopting a multiphysics analysis technique. In order to accurately estimate the temperature distribution in a variable inductor with an MR fluid-gap, the thermal solver should import the heat source from the electromagnetic solver to solve the eddy current problem. To improve accuracy, the B–H curves of the MR fluid under operating temperature were obtained using the magnetic property measurement system. In addition, the Steinmetz equation was applied to evaluate the core loss in a ferrite core. The predicted temperature rise for a variable inductor showed good agreement with the experimental data and the developed numerical technique can be employed to design a variable inductor with a high-frequency pulsed voltage source.

  3. Low voltage integrated optics electro-optical modulator applied to optical voltage transformer based on WLI technique

    Science.gov (United States)

    Santos, J. C.; Rubini, J.; Silva, L. P. C.; Caetano, R. E.

    2015-09-01

    The use of two electro-optical modulators linked in series, one for sensing and one for recovering signals, was formerly presented by some of the authors as a solution for interrogation of optical fiber sensor systems based on WLI method. A key feature required from such systems is that half-wave voltage (Vπ) of recovering modulator must be as small as possible. Aiming at meeting this requirement, in this paper it is presented the use of an unbalanced Michelson Interferometer implemented using an integrated optics component as recover interferometer in an optical voltage transformer intended for high voltage measurements.

  4. Towards an understanding of nonlinear electrokinetics at large applied voltages in concentrated solutions

    CERN Document Server

    Bazant, Martin Z; Storey, Brian D; Ajdari, Armand

    2009-01-01

    The venerable theory of electrokinetic phenomena rests on the hypothesis of a dilute solution of point-like ions in quasi-equilibrium with a weakly charged surface, whose potential relative to the bulk is of order the thermal voltage ($kT/e \\approx 25$ mV at room temperature). In nonlinear electrokinetic phenomena, such as AC or induced-charge electro-osmosis (ACEO, ICEO) and induced-charge electrophoresis (ICEP), several Volts $\\approx 100 kT/e$ are applied to polarizable surfaces in microscopic geometries, and the classical theory breaks down. In this article, we review the experimental and theoretical literatures, highlight discrepancies between theory and experiment, introduce possible modifications of the theory, and analyze their consequences. We argue that, in response to a large applied voltage, the ``compact layer'' and ``shear plane'' effectively advance into the liquid, due to the crowding of solvated counter-ions. Using simple continuum models, we predict two general trends at large voltages: (i) ...

  5. BiasMDP: Carrier lifetime characterization technique with applied bias voltage

    Energy Technology Data Exchange (ETDEWEB)

    Jordan, Paul M., E-mail: paul.jordan@namlab.com; Simon, Daniel K.; Dirnstorfer, Ingo [Nanoelectronic Materials Laboratory gGmbH (NaMLab), Nöthnitzer Straße 64, 01187 Dresden (Germany); Mikolajick, Thomas [Nanoelectronic Materials Laboratory gGmbH (NaMLab), Nöthnitzer Straße 64, 01187 Dresden (Germany); Technische Universität Dresden, Institut für Halbleiter- und Mikrosystemtechnik, 01062 Dresden (Germany)

    2015-02-09

    A characterization method is presented, which determines fixed charge and interface defect densities in passivation layers. This method bases on a bias voltage applied to an electrode on top of the passivation layer. During a voltage sweep, the effective carrier lifetime is measured by means of microwave detected photoconductivity. When the external voltage compensates the electric field of the fixed charges, the lifetime drops to a minimum value. This minimum value correlates to the flat band voltage determined in reference impedance measurements. This correlation is measured on p-type silicon passivated by Al{sub 2}O{sub 3} and Al{sub 2}O{sub 3}/HfO{sub 2} stacks with different fixed charge densities and layer thicknesses. Negative fixed charges with densities of 3.8 × 10{sup 12 }cm{sup −2} and 0.7 × 10{sup 12 }cm{sup −2} are determined for Al{sub 2}O{sub 3} layers without and with an ultra-thin HfO{sub 2} interface, respectively. The voltage and illumination dependencies of the effective carrier lifetime are simulated with Shockley Read Hall surface recombination at continuous defects with parabolic capture cross section distributions for electrons and holes. The best match with the measured data is achieved with a very low interface defect density of 1 × 10{sup 10 }eV{sup −1} cm{sup −2} for the Al{sub 2}O{sub 3} sample with HfO{sub 2} interface.

  6. Circuit-field coupled finite element analysis method for an electromagnetic acoustic transducer under pulsed voltage excitation

    Institute of Scientific and Technical Information of China (English)

    Hao Kuan-Sheng; Huang Song-Ling; Zhao Wei; Wang Shen

    2011-01-01

    This paper presents an analytical method for electromagnetic acoustic transducers (EMATs) under voltage excitation and considers the non-uniform distribution of the biased magnetic field. A complete model of EMATs including the non-uniform biased magnetic field, a pulsed eddy current field and the acoustic field is built up. The pulsed voltage excitation is transformed to the frequency domain by fast Fourier transformation (FFT). In terms of the time harmonic field equations of the EMAT system, the impedances of the coils under different frequencies are calculated according to the circuit-field coupling method and Poynting's theorem. Then the currents under different frequencies are calculated according to Ohm's law and the pulsed current excitation is obtained by inverse fast Fourier transformation (IFFT).Lastly, the sequentially coupled finite element method (FEM) is used to calculate the Lorentz force in the EMATs under the current excitation. An actual EMAT with a two-layer two-bundle printed circuit board (PCB) coil, a rectangular permanent magnet and an aluminium specimen is analysed. The coil impedances and the pulsed current are calculated and compared with the experimental results. Their agreement verified the validity of the proposed method. Furthermore, the influences of lift-off distances and the non-uniform static nagnetic field on the Lorentz force under pulsed voltage excitation are studied.

  7. Influence of Voltage Rise Time for Oxidation Treatment of NO in Simulated Exhausted Gas by Polarity-Reversed Pulse Discharge

    Science.gov (United States)

    Shinmoto, Kazuya; Kadowaki, Kazunori; Nishimoto, Sakae; Kitani, Isamu

    This paper describes experimental study on NO removal from a simulated exhausted-gas using repetitive surface discharge on a glass barrier subjected to polarity-reversed voltage pulses. The very fast polarity-reversal with a rise time of 20ns is caused by direct grounding of a charged coaxial cable of 10m in length. Influence of voltage rise time on energy efficiency for NO removal is studied. Results of NO removal using a barrier-type plasma reactor with screw-plane electrode system indicates that the energy efficiency for the very fast polarity reversal caused by direct grounding becomes higher than that for the slower polarity reversal caused by grounding through an inductor at the cable end. The energy efficiency for the direct grounding is about 80g/kWh for 50% NO removal ratio and is about 60g/kWh for 100% NO removal ratio. Very intense discharge light is observed at the initial time of 10ns for the fast polarity reversal, whereas the intensity in the initial discharge light for the slower polarity reversal is relatively small. To confirm the effectiveness of the polarity-reversed pulse application, comparison of the energy efficiency between the polarity-reversed voltage pulse and ac 60Hz voltage will be presented.

  8. Laser ultrasonic analysis of normal modes generated by a voltage pulse on an AT quartz sensor.

    Science.gov (United States)

    Goossens, Jozefien; Martinez, Loïc; Glorieux, Christ; Wilkie-Chancellier, Nicolas; Ehssein, Chighali Ould; Serfaty, Stéphane

    2006-12-22

    Laser ultrasonic detection is a versatile and highly sensitive tool for the observation of surface waves. In the following study, laser ultrasonic detection is used for the experimental study of spurious normal vibration modes of a disk quartz sensor excited by a voltage pulse. The AT cut crystal (cut of the crystal relative to the the main crystallographic axis is 35.25 degrees) is optimal for generating mainly thickness-shear vibrations (central frequency 6 MHz) on the quartz surface. However, resulting from shear-to-longitudinal and shear-to-surface mode conversion, and from the weak coupling with the other crystallographic axes, other modes (thickness-compressional and bending modes) are always present in the plate response. Since the laser vibrometer is sensitive to normal displacements, the laser investigation shows waves that can be considered as unwanted for the AT quartz used as a shear sensor. The scanned three dimensional (3D) amplitude-space-time signals are carefully analysed using their representation in three dual Fourier domains (space-time, wave number-frequency). Results on the transient analysis of the waves, the normal bending modes and the dispersion curves are shown.

  9. Morphology and Electric Conductance Change Induced by Voltage Pulse Excitation in (GeTe)2/Sb2Te3 Superlattices

    Science.gov (United States)

    Bolotov, Leonid; Saito, Yuta; Tada, Tetsuya; Tominaga, Junji

    2016-09-01

    Chalcogenide superlattice (SL) phase-change memory materials are leading candidates for non-volatile, energy-efficient electric memory where the electric conductance switching is caused by the atom repositioning in the constituent layers. Here, we study the time evolution of the electric conductance in [(GeTe)2/(Sb2Te3)1]4 SLs upon the application of an external pulsed electric field by analysing the structural and electrical responses of the SL films with scanning probe microscopy (SPM) and scanning probe lithography (SPL). At a low pulse voltage (1.6-2.3 V), a conductance switching delay of a few seconds was observed in some SL areas, where the switch to the high conductance state (HCS) is accompanied with an SL expansion under the strong electric field of the SPM probe. At a high pulse voltage (2.5-3.0 V), the HCS current was unstable and decayed in a few seconds; this is ascribed to the degradation of the HCS crystal phase under excessive heating. The reversible conductance change under a pulse voltage of opposite polarity emphasised the role of the electric field in the phase-transition mechanism.

  10. Morphology and Electric Conductance Change Induced by Voltage Pulse Excitation in (GeTe)2/Sb2Te3 Superlattices

    Science.gov (United States)

    Bolotov, Leonid; Saito, Yuta; Tada, Tetsuya; Tominaga, Junji

    2016-01-01

    Chalcogenide superlattice (SL) phase-change memory materials are leading candidates for non-volatile, energy-efficient electric memory where the electric conductance switching is caused by the atom repositioning in the constituent layers. Here, we study the time evolution of the electric conductance in [(GeTe)2/(Sb2Te3)1]4 SLs upon the application of an external pulsed electric field by analysing the structural and electrical responses of the SL films with scanning probe microscopy (SPM) and scanning probe lithography (SPL). At a low pulse voltage (1.6–2.3 V), a conductance switching delay of a few seconds was observed in some SL areas, where the switch to the high conductance state (HCS) is accompanied with an SL expansion under the strong electric field of the SPM probe. At a high pulse voltage (2.5–3.0 V), the HCS current was unstable and decayed in a few seconds; this is ascribed to the degradation of the HCS crystal phase under excessive heating. The reversible conductance change under a pulse voltage of opposite polarity emphasised the role of the electric field in the phase-transition mechanism. PMID:27618797

  11. Pulsed-voltage atom probe tomography of low conductivity and insulator materials by application of ultrathin metallic coating on nanoscale specimen geometry.

    Science.gov (United States)

    Adineh, Vahid R; Marceau, Ross K W; Chen, Yu; Si, Kae J; Velkov, Tony; Cheng, Wenlong; Li, Jian; Fu, Jing

    2017-10-01

    We present a novel approach for analysis of low-conductivity and insulating materials with conventional pulsed-voltage atom probe tomography (APT), by incorporating an ultrathin metallic coating on focused ion beam prepared needle-shaped specimens. Finite element electrostatic simulations of coated atom probe specimens were performed, which suggest remarkable improvement in uniform voltage distribution and subsequent field evaporation of the insulated samples with a metallic coating of approximately 10nm thickness. Using design of experiment technique, an experimental investigation was performed to study physical vapor deposition coating of needle specimens with end tip radii less than 100nm. The final geometries of the coated APT specimens were characterized with high-resolution scanning electron microscopy and transmission electron microscopy, and an empirical model was proposed to determine the optimal coating thickness for a given specimen size. The optimal coating strategy was applied to APT specimens of resin embedded Au nanospheres. Results demonstrate that the optimal coating strategy allows unique pulsed-voltage atom probe analysis and 3D imaging of biological and insulated samples. Copyright © 2017 Elsevier B.V. All rights reserved.

  12. Comparative study of SVPWM (space vector pulse width modulation) & SPWM (sinusoidal pulse width modulation) based three phase voltage source inverters for variable speed drive

    Science.gov (United States)

    Ahmed, Waheed; Usman Ali, Syed M.

    2013-12-01

    We have performed comparative studies of Space Vector Pulse Width Modulation (SVPWM) and Sinusoidal Pulse Width Modulation (SPWM) techniques utilizing MATLAB tools. During these investigations, we carried out intensive simulations, comprehensively analyzed the obtained results and compared the harmonic density, power factor (PF), & switching losses of SVPWM and SPWM. It has been observed during investigations that if the switching frequency is high then losses due to harmonics are negligible, thus based on obtained results we suggested that the SVPWM technique is a more reliable solution. Because SVPWM utilizes DC bus voltage more efficiently, generates less Total Harmonic Distortion (THD) and has higher output quality it provides flexible control of output voltage and output frequency for Variable Speed Drive (VSD).

  13. Plasma surface treatment to improve surface charge accumulation and dissipation of epoxy resin exposed to DC and nanosecond-pulse voltages

    Science.gov (United States)

    Zhang, Cheng; Lin, Haofan; Zhang, Shuai; Xie, Qin; Ren, Chengyan; Shao, Tao

    2017-10-01

    In this paper, deposition by non-thermal plasma is used as a surface modification technique to change the surface characteristics of epoxy resin exposed to DC and nanosecond-pulse voltages. The corresponding surface characteristics in both cases of DC and nanosecond-pulse voltages before and after the modification are compared and investigated. The measurement of the surface potential provides the surface charge distribution, which is used to show the accumulation and dissipation process of the surface charges. Morphology observations, chemical composition and electrical parameters measurements are used to evaluate the treatment effects. The experimental results show that, before the plasma treatment, the accumulated surface charges in the case of the DC voltage are more than that in the case of the nanosecond-pulse voltage. Moreover, the decay rate of the surface charges for the DC voltage is higher than that for the nanosecond-pulse voltage. However, the decay rate is no more than 41% after 1800 s for both types of voltages. After the plasma treatment, the maximum surface potentials decrease to 57.33% and 32.57% of their values before treatment for the DC and nanosecond-pulse voltages, respectively, indicating a decrease in the accumulated surface charges. The decay rate exceeds 90% for both types of voltages. These changes are mainly attributed to a change in the surface nanostructure, an increase in conductivity, and a decrease in the depth of energy level.

  14. Fault detection on the Large Hadron Collider at CERN: design, simulation and realization of a High Voltage Pulse Generator

    CERN Document Server

    Cavicchioli, C; Biagi, E; Bozzini, D

    2007-01-01

    This project was developed inside the Quality Assurance Plan (ELQA) of the LHC. The superconducting circuits of the collider show a great complexity concerning the control system, because of various reasons: the tunnel is placed around 50 to 175 m underground, the circuits work at temperatures of 1.9 K, all the structure should be perfectly aligned and the electronic part has considerable dimensions. To maximize the running time of the collider, it is necessary to develop methods for the diagnostic of defects and for the precise localization of the segment of the accelerator that contains the fault. From my studies it emerged that a possible way to localize electrical faults in the LHC superconducting circuits is to combine the use of time domain reflectometry methods and high voltage pulses. Therefore, I have designed and realized a high voltage pulse generator that will be an important instrument for the fault location among the accelerator.

  15. Transcranial low voltage pulsed electromagnetic fields in patients with treatment-resistant depression

    DEFF Research Database (Denmark)

    Martiny, Klaus Per Juul; Lunde, Marianne; Bech, Per

    2010-01-01

    BACKGROUND: Approximately 30% of patients with depression are resistant to antidepressant drugs. Repetitive transcranial magnetic stimulation (rTMS) has been found effective in combination with antidepressants in this patient group. The aim of this study was to evaluate the antidepressant effect...... of a new principle using low-intensity transcranially applied pulsed electromagnetic fields (T-PEMF) in combination with antidepressants in patients with treatment-resistant depression. METHODS: This was a sham-controlled double-blind study comparing 5 weeks of active or sham T-PEMF in patients......-resistant depression. Few side effects were observed. Mechanism of the antidepressant action, in light of the known effects of PEMF stimulation to the brain, is discussed....

  16. Pulsed power supply and coaxial reactor applied to E. coli elimination in water by pulsed dielectric barrier discharge

    Energy Technology Data Exchange (ETDEWEB)

    Quiroz V, V. E.; Lopez C, R.; Rodriguez M, B. G.; Pena E, R.; Mercado C, A.; Valencia A, R.; Hernandez A, A. N.; Barocio, S. R.; Munoz C, A. E. [ININ, Carretera Mexico-Toluca s/n, 52750 Ocoyoacac, Estado de Mexico (Mexico); De la Piedad B, A., E-mail: regulo.lopez@inin.gob.mx [Instituto Tecnologico de Toluca, Av. Tecnologico s/n, Ex-Rancho La Virgen, 52140 Metepec, Estado de Mexico (Mexico)

    2013-07-01

    The design and instrumentation intended for ATTC8739 Escherichia coli (E. coli) bacteria elimination in water, based on non thermal plasma generation at room pressure have been carried out by means of dielectric pulsed discharges. The latter have been produced by a power supply capable of providing voltages up to the order of 45 kV, 1-500 {mu}s pulse widths and variable frequencies between 100 Hz to 2000 Hz. This supply feeds a coaxial discharge reactor of the simple dielectric barrier type. The adequate operation of the system has been tested with the elimination of E. coli at 10{sup 4} and 10{sup 6} bacteria/ml concentrations, leading to reductions up to 85.3% and 95.1%, respectively, during the first 30 min of treatment. (Author)

  17. A Pulse Width Modulation Scheme With Zero-sequence Voltage Injection for Single Phase Three-level NPC Rectifiers

    Institute of Scientific and Technical Information of China (English)

    2011-01-01

    A single phase three-level converter (shown in Fig. 1) has been widely applied in high-speed railway electrical traction drive systems. But the main technical drawback of the three-level converter is DC-link neutral point voltage drift. In order to solve this problem, it is important to understand the cause of DC-link neutral point voltage drift.

  18. LMS Adaptive Filtering Applied to a Microwave Arterial Pulse Monitor

    Science.gov (United States)

    1988-12-01

    MIUTION NXTATEME A Approved for pubito r~ ehm DAprib hc"don U&tmod, 1 89 1. 7. 106 • + 5 : .. . . _ -.- + +’ .. d .. . 1 . . . .. . . AFIT/GE/ENG/88D-45...signals were low level and a certain degree of sensor repositioning was required to obtain a strong signal (greater than +/-0.2v). Once acquired...however, signal levels could be maintained at a fairly constant level even - after a slight movement of the pulse monitor. Region 3 exhibited a strong

  19. Steric effects in the dynamics of electrolytes at large applied voltages: I. Double-layer charging

    CERN Document Server

    Kilic, M S; Ajdari, A; Kilic, Mustafa Sabri; Bazant, Martin Z.; Ajdari, Armand

    2006-01-01

    The classical Poisson-Boltzmann (PB) theory of electrolytes assumes a dilute solution of point charges with mean-field electrostatic forces. Even for very dilute solutions, however, it predicts absurdly large ion concentrations (exceeding close packing) for surface potentials of only a few tenths of a volt, which are often exceeded, e.g. in microfluidic pumps and electrochemical sensors. Since the 1950s, several modifications of the PB equation have been proposed to account for the finite size of ions in equilibrium, but in this two-part series, we consider steric effects on diffuse charge dynamics (in the absence of electro-osmotic flow). In this first part, we review the literature and analyze two simple models for the charging of a thin double layer, which must form a condensed layer of close-packed ions near the surface at high voltage. A surprising prediction is that the differential capacitance typically varies non-monotonically with the applied voltage, and thus so does the response time of an electrol...

  20. Perspectives on low voltage transmission electron microscopy as applied to cell biology.

    Science.gov (United States)

    Bendayan, Moise; Paransky, Eugene

    2014-12-01

    Low voltage transmission electron microscopy (LVTEM) with accelerating voltages as low as 5 kV was applied to cell biology. To take advantage of the increased contrast given by LVTEM, tissue preparation was modified omitting all heavy metals such as osmium, uranium, and lead from the fixation, on block staining and counterstaining. Nonstained ultra-thin tissue sections (40 nm thick) generated highly contrasted images. While the aspect of the cells remains similar to that obtained by conventional TEM, some new substructures were revealed. The pancreatic acinar cells granules present a heterogeneous matrix with partitions corresponding to segregation of their different secretory proteins. Microvilli display their core of microfilaments anchored to the dense top membrane. Mitochondria revealed the presence of distinct particles along their cristea membranes that may correspond to the ATP synthase complexes or oxysomes. The dense nuclear chromatin displays a honey-comb appearance while distinct beads aligned along thin threads were seen in the dispersed chromatin. These new features revealed by LVTEM correlate with structures described or predicted through other approaches. Masking effects due to thickness of the tissue sections and to the presence of heavy metals must have prevented their observation by conventional TEM. Furthermore, the immunogold was adapted to LVTEM revealing nuclear lamin-A at the edge of the dense chromatin ribbons. Combining cytochemistry with LVTEM brings additional advantages to this new approach in cell biology.

  1. Experimental investigation of dielectric barrier discharge plasma actuators driven by repetitive high-voltage nanosecond pulses with dc or low frequency sinusoidal bias

    Science.gov (United States)

    Opaits, Dmitry F.; Likhanskii, Alexandre V.; Neretti, Gabriele; Zaidi, Sohail; Shneider, Mikhail N.; Miles, Richard B.; Macheret, Sergey O.

    2008-08-01

    Experimental studies were conducted of a flow induced in an initially quiescent room air by a single asymmetric dielectric barrier discharge driven by voltage waveforms consisting of repetitive nanosecond high-voltage pulses superimposed on dc or alternating sinusoidal or square-wave bias voltage. To characterize the pulses and to optimize their matching to the plasma, a numerical code for short pulse calculations with an arbitrary impedance load was developed. A new approach for nonintrusive diagnostics of plasma actuator induced flows in quiescent gas was proposed, consisting of three elements coupled together: the schlieren technique, burst mode of plasma actuator operation, and two-dimensional numerical fluid modeling. The force and heating rate calculated by a plasma model was used as an input to two-dimensional viscous flow solver to predict the time-dependent dielectric barrier discharge induced flow field. This approach allowed us to restore the entire two-dimensional unsteady plasma induced flow pattern as well as characteristics of the plasma induced force. Both the experiments and computations showed the same vortex flow structures induced by the actuator. Parametric studies of the vortices at different bias voltages, pulse polarities, peak pulse voltages, and pulse repetition rates were conducted experimentally. The significance of charge buildup on the dielectric surface was demonstrated. The charge buildup decreases the effective electric field in the plasma and reduces the plasma actuator performance. The accumulated surface charge can be removed by switching the bias polarity, which leads to a newly proposed voltage waveform consisting of high-voltage nanosecond repetitive pulses superimposed on a high-voltage low frequency sinusoidal voltage. Advantages of the new voltage waveform were demonstrated experimentally.

  2. Low Voltage Electrolytic Capacitor Pulse Forming Inductive Network for Electric Weapons

    Science.gov (United States)

    2006-06-01

    reliable high- current, high-energy pulses of many megawatts. Pulsed alternators potentially have the same maintenance issues as other motor...high-energy pulses of many megawatts. Pulsed alternators potentially have the same maintenance issues as other motor-generator sets, so a solid...on an all-electric ship, those challenges are being met. The naval railgun, the army railgun, coilguns , and other electric weapon systems such as

  3. Hydrodynamic flow in the vicinity of a nanopore induced by an applied voltage

    CERN Document Server

    Mao, Mao; Hu, Guohui

    2013-01-01

    Continuum simulation is employed to study ion transport and fluid flow through a nanopore in a solid-state membrane under an applied potential drop. Results show the existence of concentration polarization layers on the surfaces of the membrane. The nonuniformity of the ionic distribution gives rise to an electric pressure that drives vortical motion in the fluid. There is also a net hydrodynamic flow through the nanopore due to an asymmetry induced by the membrane surface charge. The qualitative behavior is similar to that observed in a previous study using molecular dynamic simulations. The current--voltage characteristics show some nonlinear features but are not greatly affected by the hydrodynamic flow in the parameter regime studied. In the limit of thin Debye layers, the electric resistance of the system can be characterized using an equivalent circuit with lumped parameters. Generation of vorticity can be understood qualitatively from elementary considerations of the Maxwell stresses. However, the flow...

  4. Sub-nanosecond time resolved light emission study for diffuse discharges in air under steep high voltage pulses

    Science.gov (United States)

    Tardiveau, P.; Magne, L.; Marode, E.; Ouaras, K.; Jeanney, P.; Bournonville, B.

    2016-10-01

    Pin-to-plane discharges in centimetre air gaps and standard conditions of pressure and temperature are generated under very high positive nanosecond scale voltage pulses. The experimental study is based on recordings of sub-nanosecond time resolved and Abel-processed light emission profiles and their complete correlation to electrical current waveforms. The effects of the voltage pulse features (amplitude between 20 and 90 kV, rise time between 2 and 5.2 ns, and time rate between 4 and 40 kV · ns‑1) and the electrode configuration (gap distance between 10 and 30 mm, pin radius between 10 and 200 µm, copper, molybdenum or tungsten pin material) are described. A three time period development can be found: a glow-like structure with monotonic light profiles during the first 1.5 ns whose size depends on time voltage rate, a shell-like structure with bimodal profiles whose duration and extension in space depends on rise time, and either diffuse or multi-channel regime for the connection to the cathode plane according to gap distance. The transition of the light from monotonic to bimodal patterns reveals the relative effects and dynamics of streamer space charge and external laplacian field. A classical 2D-fluid model for streamer propagation has been used and adapted for very high and steep voltage pulses. It shows the formation of a strong space charge (streamer) very close to the pin, but also a continuity of emission between the pin and the streamer, and electric fields higher than the critical ionization field (28 kV · cm‑1 in air) almost in the whole gap and very early in the discharge propagation.

  5. Nanosecond pulsed power generator for a voltage amplitude up to 300 kV and a repetition rate up to 16 Hz for fine disintegration of quartz

    Energy Technology Data Exchange (ETDEWEB)

    Krastelev, E. G., E-mail: ekrastelev@yandex.ru; Sedin, A. A.; Tugushev, V. I. [Russian Academy of Sciences, Joint Institute for High Temperatures (Russian Federation)

    2015-12-15

    A generator of high-power high-voltage nanosecond pulses is intended for electrical discharge disintegration of mineral quartz and other nonconducting minerals. It includes a 320 kV Marx pulsed voltage generator, a high-voltage glycerin-insulated coaxial peaking capacitor, and an output gas spark switch followed by a load, an electric discharge disintegration chamber. The main parameters of the generator are as follows: a voltage pulse amplitude of up to 300 kV, an output impedance of ≈10 Ω, a discharge current amplitude of up to 25 kA for a half-period of 80–90 ns, and a pulse repetition rate of up to 16 Hz.

  6. A new pulse modulation adaptive controller (PMAC) applied to HVAC systems

    Energy Technology Data Exchange (ETDEWEB)

    Salsbury, T.I. [Johnson Controls Inc., Milwaukee (United States)

    2002-12-01

    The paper proposes a new switching control law (pulse modulation adaptive controller, PMAC) that implements pulse-width-pulse-frequency modulation. Pulse durations are determined to maintain the amplitude of variation in the controlled variable at or below a user-defined level. In addition to providing quantifiable control performance, PMAC can reduce component wear by issuing fewer switches than conventional control schemes. The control law is developed around a first-order system characterization but incorporates an adaptive loop, which allows application to a wide range of non-first-order and also time-variant systems. Test results are presented from applying PMAC to both simulated and real HVAC systems. (author)

  7. Coherent control with shaped femtosecond laser pulses applied to ultracold molecules

    CERN Document Server

    Salzmann, W; Wester, R; Weidemüller, M; Merli, A; Weber, S M; Sauer, F; Plewicki, M; Weise, F; Esparza, A M; Wöste, L; Lindinger, A; Salzmann, Wenzel; Poschinger, Ulrich; Wester, Roland; Weidemueller, Matthias; Merli, Andrea; Weber, Stefan M.; Sauer, Franziska; Plewicki, Mateusz; Weise, Fabian; Esparza, Aldo Mirabal; Woeste, Ludger; Lindinger, Albrecht

    2005-01-01

    We report on coherent control of excitation processes of translationally ultracold rubidium dimers in a magneto-optical trap by using shaped femtosecond laser pulses. Evolution strategies are applied in a feedback loop in order to optimize the photoexcitation of the Rb2 molecules, which subsequently undergo ionization or fragmentation. A superior performance of the resulting pulses compared to unshaped pulses of the same pulse energy is obtained by distributing the energy among specific spectral components. The demonstration of coherent control to ultracold ensembles opens a path to actively influence fundamental photo-induced processes in molecular quantum gases.

  8. Study on the influence of applied voltage and feed concentration on the performance of electrodeionization

    Directory of Open Access Journals (Sweden)

    Yohanes Ervan1

    2002-11-01

    Full Text Available Electrodeionization (EDI, a membrane process for removing ion from aqueous feed, becomes more popular nowadays. Its ability to produce ultrapure water gives significant contributions to chemical and semiconductor industries. Only few researches have been published to evaluate its performance in producing ultrapure water, especially in studying and analysing the relation between process parameter and its performance. This work is intended to observe and evaluate the influence of voltage applied and feed concentration on EDI performance. The raw material used in experiment is tap water filtered by reverse osmosis unit before proceeding to the electrodeionization. Product analysis, the diluate as well as the concentrate, is carried out by using conductivity meter and pH meter. The experimental results are presented in i vs V curve, product conductivity vs time, and product pH vs time. From experimental results, it is concluded that concentration polarization can be minimized in EDI process, the increasing of applied current increases product pH. However, there is a limit in gradient concentration between feed and concentrate to minimize the occurence of counter diffusion phenomena.

  9. Characterization of Multicrystalline Silicon Modules with System Bias Voltage Applied in Damp Heat

    Energy Technology Data Exchange (ETDEWEB)

    Hacke, P.; Kempe, M.; Terwilliger, K.; Glick, S.; Call, N.; Johnston, S.; Kurtz, S.

    2011-07-01

    As it is considered economically favorable to serially connect modules to build arrays with high system voltage, it is necessary to explore potential long-term degradation mechanisms the modules may incur under such electrical potential. We performed accelerated lifetime testing of multicrystalline silicon PV modules in 85 degrees C/ 85% relative humidity and 45 degrees C/ 30% relative humidity while placing the active layer in either positive or negative 600 V bias with respect to the grounded module frame. Negative bias applied to the active layer in some cases leads to more rapid and catastrophic module power degradation. This is associated with significant shunting of individual cells as indicated by electroluminescence, thermal imaging, and I-V curves. Mass spectroscopy results support ion migration as one of the causes. Electrolytic corrosion is seen occurring with the silicon nitride antireflective coating and silver gridlines, and there is ionic transport of metallization at the encapsulant interface observed with damp heat and applied bias. Leakage current and module degradation is found to be highly dependent upon the module construction, with factors such as encapsulant and front glass resistivity affecting performance. Measured leakage currents range from about the same seen in published reports of modules deployed in Florida (USA) and is accelerated to up to 100 times higher in the environmental chamber testing.

  10. High-voltage isolation transformer for sub-nanosecond rise time pulses constructed with annular parallel-strip transmission lines.

    Science.gov (United States)

    Homma, Akira

    2011-07-01

    A novel annular parallel-strip transmission line was devised to construct high-voltage high-speed pulse isolation transformers. The transmission lines can easily realize stable high-voltage operation and good impedance matching between primary and secondary circuits. The time constant for the step response of the transformer was calculated by introducing a simple low-frequency equivalent circuit model. Results show that the relation between the time constant and low-cut-off frequency of the transformer conforms to the theory of the general first-order linear time-invariant system. Results also show that the test transformer composed of the new transmission lines can transmit about 600 ps rise time pulses across the dc potential difference of more than 150 kV with insertion loss of -2.5 dB. The measured effective time constant of 12 ns agreed exactly with the theoretically predicted value. For practical applications involving the delivery of synchronized trigger signals to a dc high-voltage electron gun station, the transformer described in this paper exhibited advantages over methods using fiber optic cables for the signal transfer system. This transformer has no jitter or breakdown problems that invariably occur in active circuit components.

  11. Research on Nanosecond Pulse Corona Discharge with Cross Magnetic Field Applied

    Institute of Scientific and Technical Information of China (English)

    HE Zheng-hao; YU Fu-sheng; HU Feng; YUAN Yun; GUO Li-na; LI Jin

    2007-01-01

    An application of magnetic field to the nanosecond pulse corona discharge is investigated.A cylinder reactor with different corona electodes is set up for experimental study.A manetic field with its direction perpendicular to the corona discharge is applied.Different discharge images are taken under single nanosecond pulse with a high sensitive UV-visible light imagine recorder.Experimental results show that with a cross magnetic field the nanosecond out the magnetic field. The results may lead to a possibility to apply a cross magnetic field on nanosecond pulse corona discharge for getting higher desulfurization effciency.

  12. Impact of pulsed-electric field and high-voltage electrical discharges on red wine microbial stabilization and quality characteristics.

    Science.gov (United States)

    Delsart, C; Grimi, N; Boussetta, N; Miot Sertier, C; Ghidossi, R; Vorobiev, E; Mietton Peuchot, M

    2016-01-01

    In this study, pulsed-electric fields (PEF) and high-voltage electrical discharges (HVED) are proposed as new techniques for the microbial stabilization of red wines before bottling. The efficiency of the treatment was then evaluated. PEF and HVED-treatments have been applied to wine for the inactivation of Oenococcus oeni CRBO 9304, O. oeni CRBO 0608, Pediococcus parvulus CRBO 2.6 and Brettanomyces bruxellensis CB28. Different treatment times (1, 2, 4, 6, 8 and 10 ms) were used at 20 kV cm(-1) for the PEF treatments and at 40 kV for the HVED treatments, which correspond to applied energies from 80 to 800 kJ l(-1) . The effects of the treatments on the microbial inactivation rate and on various characteristics of red wines (phenolic composition, chromatic characteristics and physico-chemical parameters) were measured. The application of PEF or HVED treatments on red wine allowed the inactivation of alteration yeasts (B. bruxellensis CB28) and bacteria (O. oeni CRBO 9304, O. oeni CRBO 0608 and P. parvulus CRBO 2.6). The electric discharges at 40 kV were less effective than the PEF even after 10 ms of treatments. Indeed, 4 ms of PEF treatment at 20 kV cm(-1) were sufficient to inactivate all micro-organisms present in the wines. Also, the use of PEF had no negative impact on the composition of wines compared to the HVED treatments. Contrary to PEF, the phenolics compounds were degraded after the HVED treatment and the physico-chemical composition of wine were modified with HVED. PEF technology seems to be an interesting alternative to stabilize microbiologically wines before bottling and without modifying their composition. This process offers many advantages for winemakers: no chemical inputs, low energy consumption (320 kJ l(-1) ), fast (treatment time of 4 ms) and athermal (ΔT ≈ 10°C). © 2015 The Society for Applied Microbiology.

  13. Isolated PWM DC-AC SICAM with an active capacitive voltage clamp[Pulse Density Modulated; Pulse Width Modulation

    Energy Technology Data Exchange (ETDEWEB)

    Ljusev, P.

    2004-03-15

    In this report an isolated PWM DC-AC SICAM with an active capacitive voltage clamp is presented. AC-DC power supply is implemented in its simplest form: diode rectifier followed by a medium-size charge-storage capacitors and possibly with an EMC filter on the mains entrance. Isolation from the AC mains is achieved using a high frequency (HF) transformer, whose voltages are not audio-modulated. The latter simplifies the design and is expected to have many advantages over the approach where the transformer voltages are modulated in regards to the audio signal reference. Input stage is built as a DC-AC inverter (push-pull, half-bridge or a full-bridge) and operated with 50% duty cycle, with all the challenges to avoid transformer saturation and obtain symmetrical operation. On the secondary side the output section is implemented as rectifier+inverter AC-AC stage, i.e. a true bidirectional bridge, which operation is aimed towards amplification of the audio signal. In order to solve the problem with the commutation of the load current, a dead time between the incoming and outgoing bidirectional switch is implemented, while a capacitive voltage clamp is used to keep the induced overvoltage to reasonable levels. The energy stored in the clamping capacitor is not wasted as in the dissipative clamps, but is rather transferred back to the primary side for further processing using an auxiliary isolated single-switch converter, i.e. an active clamping technique is used. (au)

  14. Comparison of atmospheric air plasmas excited by high-voltage nanosecond pulsed discharge and sinusoidal alternating current discharge

    Science.gov (United States)

    Zhang, Shuai; Wang, Wen-chun; Jiang, Peng-chao; Yang, De-zheng; Jia, Li; Wang, Sen

    2013-10-01

    In this paper, atmospheric pressure air discharge plasma in quartz tube is excited by 15 ns high-voltage nanosecond pulsed discharge (HVNPD) and sinusoidal alternating current discharge (SACD), respectively, and a comparison study of these two kinds of discharges is made through visual imaging, electrical characterization, optical detection of active species, and plasma gas temperature. The peak voltage of the power supplies is kept at 16 kV while the pulse repetition rate of nanosecond pulse power supply is 100 Hz, and the frequency of sinusoidal power supply is 10 kHz. Results show that the HVNPD is uniform while the SACD presents filamentary mode. For exciting the same cycles of discharge, the average energy consumption in HVNPD is about 1/13 of the SACD. However, the chemical active species generated by the HVNPD is about 2-9 times than that excited by the SACD. Meanwhile, the rotational and vibrational temperatures have been obtained via fitting the simulated spectrum of N2 (C3Πu → B3Πg, 0-2) with the measured one, and the results show that the plasma gas temperature in the HVNPD remains close to room temperature whereas the plasma gas temperature in the SACD is about 200 K higher than that in HVNPD in the initial phase and continually increases as discharge exposure time goes on.

  15. A simplified method for estimation of iron loss in wound toroidal cores energised by pulse width modulated voltage sources

    Science.gov (United States)

    Tutkun, Nedim; Moses, Anthony J.

    2004-12-01

    Recently the strip wound toroidal cores have increasingly been used in switching mode and uninterruptible power supplies for a wide range of industrial applications. Therefore, the prediction of iron loss increase in such magnetic cores energised by non-sinusoidal voltage excitation is important step in the design of electromagnetic devices. In this investigation, a loss increase was estimated by determination of unknown constants in a previously developed loss separation model using genetic algorithms. Also the skin effect of flux density was taken into account for estimation of power loss under pulse width modulated voltage sources. The results obtained are in good agreement with the measured results in wound toroids at various flux densities.

  16. Development in food nonthermal sterilization with high-voltage pulsed generator%食品冷杀菌用高压脉冲发生器的研制

    Institute of Scientific and Technical Information of China (English)

    杜存臣; 吴清

    2011-01-01

    为开展高压脉冲电场冷杀菌研究,研制高压脉冲发生器,主要由单片机控制单元、AT89S52单片机、脉冲驱动模块、高压脉冲变压器和交流调压单元组成,具备脉冲电压、脉冲频率和脉冲宽度等参数可以同时调节的特点,为开展冷杀菌技术研究的脉冲电源研制提供一种可行的技术途径.%For the development of the high-voltage pulsed electric field P nonthermal sterilization , design and make high-voltage pulsed genera- H tor. It mainly by single-chip microcomputer control unit, AT89S52 SCM, pulse driver modules, high pressure pulse transformer and alternating voltage regulation of elements have pulse voltage and pulse frequency and pulse width and can adjust the parameters such as characteristics, in the nonthermal sterilization technology research development pulse power provides a feasible technology way.

  17. Five-Level Converter with Low Switching Frequency Applied as DC Voltage Supply

    DEFF Research Database (Denmark)

    Rasmussen, Tonny Wederberg

    1999-01-01

    This paper describes the use of a multi-level converter as a DC supply. Equations for the converter will be deduced in the nondissipative case. The equations provide solutions to DC voltage and the angle of converter voltage. In addition the spectrum for the harmonics after the elimination...

  18. High voltage generator circuit with low power and high efficiency applied in EEPROM

    Institute of Scientific and Technical Information of China (English)

    Liu Yan; Zhang Shilin; Zhao Yiqiang

    2012-01-01

    This paper presents a low power and high efficiency high voltage generator circuit embedded in electrically erasable programmable read-only memory (EEPROM).The low power is minimized by a capacitance divider circuit and a regulator circuit using the controlling clock switch technique.The high efficiency is dependent on the zero threshold voltage (Vth) MOSFET and the charge transfer switch (CTS) charge pump.The proposed high voltage generator circuit has been implemented in a 0.35μm EEPROM CMOS process.Measured results show that the proposed high voltage generator circuit has a low power consumption of about 150.48 μW and a higher pumping efficiency (83.3%) than previously reported circuits.This high voltage generator circuit can also be widely used in low-power flash devices due to its high efficiency and low power dissipation.

  19. Investigation on the energy spectrums of electrons in atmospheric pressure argon plasma jets and their dependences on the applied voltage

    Science.gov (United States)

    Chen, Xinxian; Tan, Zhenyu; Liu, Yadi; Li, Xiaotong; Pan, Jie; Wang, Xiaolong

    2017-08-01

    This work presents a systematical investigation on the spatiotemporal evolution of the energy spectrum of electrons in atmospheric pressure argon plasma jets and its dependence on the applied voltage. The investigations are carried out by means of the numerical simulation based on a particle-in-cell Monte-Carlo collision model. The characteristics of the spatiotemporal evolution of the energy spectrum of electrons (ESE) in the discharge space have been presented, and especially the mechanisms of inducing these characteristics have also been revealed. The present work shows the following conclusions. In the evolution of ESE, there is a characteristic time under each applied voltage. Before the characteristic time, the peak value of ESE decreases, the peak position shifts toward high energy, and the distribution of ESE becomes wider and wider, but the reverse is true after the characteristic time. The formation of these characteristics can be mainly attributed to the transport of electrons toward a low electric field as well as a balance between the energy gained from the electric field including the effect of space charges and the energy loss due to inelastic collisions in the process of electron transport. The characteristic time decreases with the applied voltage. In addition, the average energy of electrons at the characteristic time can be increased by enhancing the applied voltage. The results presented in this work are of importance for regulating and controlling the energy of electrons in the plasma jets applied to plasma medicine.

  20. High-voltage Pulsed Electric Field in.Food Industry%食品高压脉冲电场杀菌技术

    Institute of Scientific and Technical Information of China (English)

    袁丽佳; 何博; 姜彬; 尤涛

    2011-01-01

    High-voltage pulsed electric field is one of the most popular methods in food process. The mechanism of high-voltage pulsed electric field, the device of high-vo]tage pulsed electric field , and the application of it are introduced.%高压脉冲电场(high-voltage pulsed electric field,HPEF)杀菌技术是目前国际上最热门的食品加工技术之一,本文介绍了高压脉冲电场杀菌技术的基本机理,杀菌装置,以及对该技术在食品加工中应用的介绍。

  1. Simulations of atmospheric pressure discharge in a high-voltage nanosecond pulse using the particle-in-cell Monte Carlo collision model in noble gases

    Science.gov (United States)

    Shi, Feng; Wang, Dezhen; Ren, Chunsheng

    2008-06-01

    Atmospheric pressure discharge nonequilibrium plasmas have been applied to plasma processing with modern technology. Simulations of discharge in pure Ar and pure He gases at one atmospheric pressure by a high voltage trapezoidal nanosecond pulse have been performed using a one-dimensional particle-in-cell Monte Carlo collision (PIC-MCC) model coupled with a renormalization and weighting procedure (mapping algorithm). Numerical results show that the characteristics of discharge in both inert gases are very similar. There exist the effects of local reverse field and double-peak distributions of charged particles' density. The electron and ion energy distribution functions are also observed, and the discharge is concluded in the view of ionization avalanche in number. Furthermore, the independence of total current density is a function of time, but not of position.

  2. Reactive Power Compensation of a 24 MW Wind Farm using a 12-Pulse Voltage Source Converter

    DEFF Research Database (Denmark)

    Pedersen, Knud Ole Helgesen; Pedersen, Jørgen Kaas

    1998-01-01

    Integration of large wind farms in distribution and transmission systems may have severe influence on the power quality at the connection point and may also influence the voltage controlling capability of the electrical system. The purpose of the described project has been to develop and investig......Integration of large wind farms in distribution and transmission systems may have severe influence on the power quality at the connection point and may also influence the voltage controlling capability of the electrical system. The purpose of the described project has been to develop...... and investigate the use of a STATCOM by modelling and field testing an 8 MVar unit in a 24 MW wind farm....

  3. Space Vector Pulse Width Modulation Scheme for a Seven-Phase Voltage Source Inverter

    Directory of Open Access Journals (Sweden)

    Mohd. Arif Khan

    2011-09-01

    Full Text Available This paper analyses a simple space vector PWM (SVPWM scheme for a seven-phase voltage source inverter. At first the conventional method of producing sinusoidal output voltage  by utilizing six active and a zero space vectors are used to synthesis the input reference and then new PWM scheme called time equivalent space vector PWM is presented.  A comparison of the proposed scheme with the conventional scheme is presented based on various performance indices. Extensive Simulation results are provided to validate the findings

  4. Pulsed voltage deposited lead selenide thin film as efficient counter electrode for quantum-dot-sensitized solar cells

    Energy Technology Data Exchange (ETDEWEB)

    Jin, Bin Bin [Key Laboratory of Macromolecular Science of Shaanxi Province & School of Materials Science and Engineering, Shaanxi Normal University, Xi’an 710062 (China); Department of Chemical Engineering, Institute of Chemical Industry, Shaanxi Institute of Technology, Xi’an 710300 (China); Wang, Ye Feng [Key Laboratory of Macromolecular Science of Shaanxi Province & School of Materials Science and Engineering, Shaanxi Normal University, Xi’an 710062 (China); Wang, Xue Qing [Faculty of Chemical, Environmental and Biological Science and Technology, Dalian University of Technology, Dalian 116024 (China); Zeng, Jing Hui, E-mail: jhzeng@ustc.edu [Key Laboratory of Macromolecular Science of Shaanxi Province & School of Materials Science and Engineering, Shaanxi Normal University, Xi’an 710062 (China)

    2016-04-30

    Highlights: • PbSe thin film is deposited on FTO glass by a pulse voltage electrodeposition method. • The thin film is used as counter electrode (CE) in quantum dot-sensitized solar cell. • Superior electrocatalytic activity and stability in the polysulfide electrolyte is received. • The narrow band gap characteristics and p-type conductivity enhances the cell efficiency. • An efficiency of 4.67% is received for the CdS/CdSe co-sensitized solar cells. - Abstract: Lead selenide (PbSe) thin films were deposited on fluorine doped tin oxide (FTO) glass by a facile one-step pulse voltage electrodeposition method, and used as counter electrode (CE) in CdS/CdSe quantum dot-sensitized solar cells (QDSSCs). A power conversion efficiency of 4.67% is received for the CdS/CdSe co-sensitized solar cells, which is much better than that of 2.39% received using Pt CEs. The enhanced performance is attributed to the extended absorption in the near infrared region, superior electrocatalytic activity and p-type conductivity with a reflection of the incident light at the back electrode in addition. The physical and chemical properties were characterized by X-ray diffraction (XRD), scanning electron microscope (SEM), transmission electron microscopy (TEM), energy-dispersive spectroscopy (EDS), reflectance spectra, electrochemical impedance spectroscopy (EIS) and Tafel polarization measurements. The present work provides a facile pathway to an efficient CE in the QDSSCs.

  5. The Preceding Voltage Pulse and Separation Welding Mechanism of Electrical Contacts

    DEFF Research Database (Denmark)

    Yang, Xiao Cheng; Huang, Jiang; Li, Zhen Biao

    2016-01-01

    In order to obtain a better understanding of the welding mechanism in contact separation, electrical endurance tests were conducted with AgSnO2 and AgNi contacts on a simulation test device. Waveforms of contact displacement, contact voltage, and current were recorded with LabVIEW during the tests...

  6. Transistorized Marx bank pulse circuit provides voltage multiplication with nanosecond rise-time

    Science.gov (United States)

    Jung, E. A.; Lewis, R. N.

    1968-01-01

    Base-triggered avalanche transistor circuit used in a Marx bank pulser configuration provides voltage multiplication with nanosecond rise-time. The avalanche-mode transistors replace conventional spark gaps in the Marx bank. The delay time from an input signal to the output signal to the output is typically 6 nanoseconds.

  7. Nanosecond pulsed electric fields (nsPEFs) low cost generator design using power MOSFET and Cockcroft-Walton multiplier circuit as high voltage DC source

    Science.gov (United States)

    Sulaeman, M. Y.; Widita, R.

    2014-09-01

    Purpose: Non-ionizing radiation therapy for cancer using pulsed electric field with high intensity field has become an interesting field new research topic. A new method using nanosecond pulsed electric fields (nsPEFs) offers a novel means to treat cancer. Not like the conventional electroporation, nsPEFs able to create nanopores in all membranes of the cell, including membrane in cell organelles, like mitochondria and nucleus. NsPEFs will promote cell death in several cell types, including cancer cell by apoptosis mechanism. NsPEFs will use pulse with intensity of electric field higher than conventional electroporation, between 20-100 kV/cm and with shorter duration of pulse than conventional electroporation. NsPEFs requires a generator to produce high voltage pulse and to achieve high intensity electric field with proper pulse width. However, manufacturing cost for creating generator that generates a high voltage with short duration for nsPEFs purposes is highly expensive. Hence, the aim of this research is to obtain the low cost generator design that is able to produce a high voltage pulse with nanosecond width and will be used for nsPEFs purposes. Method: Cockcroft-Walton multiplier circuit will boost the input of 220 volt AC into high voltage DC around 1500 volt and it will be combined by a series of power MOSFET as a fast switch to obtain a high voltage with nanosecond pulse width. The motivation using Cockcroft-Walton multiplier is to acquire a low-cost high voltage DC generator; it will use capacitors and diodes arranged like a step. Power MOSFET connected in series is used as voltage divider to share the high voltage in order not to damage them. Results: This design is expected to acquire a low-cost generator that can achieve the high voltage pulse in amount of -1.5 kV with falltime 3 ns and risetime 15 ns into a 50Ω load that will be used for nsPEFs purposes. Further detailed on the circuit design will be explained at presentation.

  8. Nanosecond pulsed electric fields (nsPEFs) low cost generator design using power MOSFET and Cockcroft-Walton multiplier circuit as high voltage DC source

    Energy Technology Data Exchange (ETDEWEB)

    Sulaeman, M. Y.; Widita, R. [Department of Physics, Nuclear Physics and Biophysics Research Division, Faculty of Mathematics and Natural Science, Institut Teknologi Bandung, Bandung (Indonesia)

    2014-09-30

    Purpose: Non-ionizing radiation therapy for cancer using pulsed electric field with high intensity field has become an interesting field new research topic. A new method using nanosecond pulsed electric fields (nsPEFs) offers a novel means to treat cancer. Not like the conventional electroporation, nsPEFs able to create nanopores in all membranes of the cell, including membrane in cell organelles, like mitochondria and nucleus. NsPEFs will promote cell death in several cell types, including cancer cell by apoptosis mechanism. NsPEFs will use pulse with intensity of electric field higher than conventional electroporation, between 20–100 kV/cm and with shorter duration of pulse than conventional electroporation. NsPEFs requires a generator to produce high voltage pulse and to achieve high intensity electric field with proper pulse width. However, manufacturing cost for creating generator that generates a high voltage with short duration for nsPEFs purposes is highly expensive. Hence, the aim of this research is to obtain the low cost generator design that is able to produce a high voltage pulse with nanosecond width and will be used for nsPEFs purposes. Method: Cockcroft-Walton multiplier circuit will boost the input of 220 volt AC into high voltage DC around 1500 volt and it will be combined by a series of power MOSFET as a fast switch to obtain a high voltage with nanosecond pulse width. The motivation using Cockcroft-Walton multiplier is to acquire a low-cost high voltage DC generator; it will use capacitors and diodes arranged like a step. Power MOSFET connected in series is used as voltage divider to share the high voltage in order not to damage them. Results: This design is expected to acquire a low-cost generator that can achieve the high voltage pulse in amount of −1.5 kV with falltime 3 ns and risetime 15 ns into a 50Ω load that will be used for nsPEFs purposes. Further detailed on the circuit design will be explained at presentation.

  9. Recent progress in R&D for long pulse and ultra-high voltage components for the ITER HNB

    Energy Technology Data Exchange (ETDEWEB)

    Kashiwagi, Mieko, E-mail: kashiwagi.mieko@jaea.go.jp; Umeda, Naotaka; Kojima, Atsushi; Yoshida, Masafumi; Tobari, Hiroyuki; Dairaku, Masayuki; Yamanaka, Haruhiko; Maejima, Tetsuya; Yamashita, Yasuo; Shibata, Naoki; Watanabe, Kazuhiro; Hanada, Masaya

    2015-10-15

    Highlights: • Long-pulse acceleration of MeV-class ion beams is demonstrated in JAEA. • The pulse length is extended from 0.4 s to 60 s, successfully. • R&D of 1 MV power supply is in progressed as scheduled. • Feasibility of 1 MV insulating transformer is confirmed in the mockup. - Abstract: Toward ITER, the long-pulse acceleration of MeV-class negative ion beams has been successfully demonstrated and R&Ds and the procurement of high-voltage components of 1 MV power supply system have been progressed. In the accelerator development after the production of 1 MeV beams, an extraction grid, where a water cooling is reinforced and the beam is steered by aperture offset to suppress grid heat loads, has been newly developed to extend the pulse duration of the MeV-class beams. As the result, a total grid heat load has been reduced from 20% to 10% of the total beam power. The beam pulse was successfully increased from 0.4 s to 60 s at 0.68 MeV, 100 A/m{sup 2} and 12 s at 0.89 MeV, 156 A/m{sup 2} beams. As for the procurement of the 1 MV power supply system, 1 MV insulating transformer as the critical component has been developed. In the mock-up, a dc 1.2 MV for 1 h with the margin of 20% was stably sustained. Through the R&Ds of the critical components, design of five power supplies procured by JAEA has been finalized, and out of which a testing power supply has been completed in June 2014.

  10. Technical Conditions of Microgenerator Connection to a Low Voltage Network Taking Into Account Valid Rules and Practices Applied in Europe and Poland

    Directory of Open Access Journals (Sweden)

    Marian Sobierajski

    2014-12-01

    Full Text Available Connection of microgenerators to a low voltage network affects the electrical energy quality. In the paper, the basic relationships have been set out to compute voltage deviations and fluctuations. The basic criteria of microgeneration connection to a low voltage network have been given. The valid rules and practices applied in Europe and Poland have been described.

  11. Physiological effects of high- and low-voltage pulse combinations for gene electrotransfer in muscle

    DEFF Research Database (Denmark)

    Hojman, Pernille; Gissel, Hanne; Andre, Franck M;

    2008-01-01

    Gene transfer by electroporation is gaining momentum now that high-level, long-term expression of transgenes is being obtained. Several different pulse regimens are efficient, yet little information is available about the physiological muscular response to gene electrotransfer. This paper provide...

  12. Pulse and Trapezoidal Voltage Clamp Applied To Jurkat Cells: A T- Lymphocyte Cell Line

    Science.gov (United States)

    1993-04-01

    clamp. (Upward deflection represents depolarization). Low frequency oscillations are clearly visible. Such oscillations have been described by Maltsev ...1952. (8) Maltsev , V. A. Oscillating and triggering properties of T cell membrane potential. Imun. Lett. 26:277-282, 1990. 13 (9) Gallin, E. K

  13. Effect of applied dc bias voltage on composition, chemical bonding and mechanical properties of carbon nitride films prepared by PECVD

    Institute of Scientific and Technical Information of China (English)

    LI Hong-xuan; XU Tao; HAO Jun-ying; CHEN Jian-min; ZHOU Hui-di; XUE Qun-ji; LIU Hui-wen

    2004-01-01

    Carbon nitride films were deposited on Si (100) substrates using plasma-enhanced chemical vapor deposition (PECVD) technique from CH4 and N2 at different applied dc bias voltage. The microstructure, composition and chemical bonding of the resulting films were characterized by Raman spectroscopy, Fourier transform infrared spectroscopy (FTIR), X-ray photoelectron spectroscopy (XPS) and X-ray diffraction (XRD). The mechanical properties such as hardness and elastic modulus of the films were evaluated using nano-indentation. As the results, the Raman spectra, showing the G and D bands, indicate the amorphous structure of the films. XPS and FTIR measurements demonstrate the existence of various carbon-nitride bonds in the films and the hydrogenation of carbon nitride phase. The composition ratio of N to C, the nano-hardness and the elastic modulus of the carbon nitride films increase with increasing dc bias voltage and reach the maximums at a dc bias voltage of 300 V, then they decrease with further increase of the dc bias voltage. Moreover, the XRD analyses indicate that the carbon nitride film contains some polycrystalline C3N4 phase embedded in the amorphous matrix at optimized deposition condition of dc bias voltage of 300 V.

  14. Pulsed terahertz spectroscopy and imaging applied to inspection of explosives and inflammable liquids

    Science.gov (United States)

    Yamamoto, Kohji; Yamaguchi, Mariko; Miyamaru, Fumiaki; Tani, Masahiko; Hangyo, Masanori; Ikeda, Takeshi; Matsushita, Akira; Koide, Kenji; Tatsuno, Michiaki; Manami, Yukio

    We carried out applied researches on the pulsed terahertz spectroscopy and the terahertz imaging to detect the C-4 explosive hidden in a mail and inflammable liquids stored in plastic bottles. We confirm that THz techniques are quite efficient at contactless and nondestructive inspection of hazardous materials used in terrorist activities.

  15. Voltage-controlled magnetization switching in MRAMs in conjunction with spin-transfer torque and applied magnetic field

    Science.gov (United States)

    Munira, Kamaram; Pandey, Sumeet C.; Kula, Witold; Sandhu, Gurtej S.

    2016-11-01

    Voltage-controlled magnetic anisotropy (VCMA) effect has attracted a significant amount of attention in recent years because of its low cell power consumption during the anisotropy modulation of a thin ferromagnetic film. However, the applied voltage or electric field alone is not enough to completely and reliably reverse the magnetization of the free layer of a magnetic random access memory (MRAM) cell from anti-parallel to parallel configuration or vice versa. An additional symmetry-breaking mechanism needs to be employed to ensure the deterministic writing process. Combinations of voltage-controlled magnetic anisotropy together with spin-transfer torque (STT) and with an applied magnetic field (Happ) were evaluated for switching reliability, time taken to switch with low error rate, and energy consumption during the switching process. In order to get a low write error rate in the MRAM cell with VCMA switching mechanism, a spin-transfer torque current or an applied magnetic field comparable to the critical current and field of the free layer is necessary. In the hybrid processes, the VCMA effect lowers the duration during which the higher power hungry secondary mechanism is in place. Therefore, the total energy consumed during the hybrid writing processes, VCMA + STT or VCMA + Happ, is less than the energy consumed during pure spin-transfer torque or applied magnetic field switching.

  16. Design and Fabrication of Micromechanical Optical Switches Based on the Low Applied Voltage

    Institute of Scientific and Technical Information of China (English)

    2003-01-01

    A micromechanical optical switch driven by electrostatic was fabricated with (100) silicon and tilted 2.5° (111) silicon. The pull-in voltage is 13.2V, the insertion loss is less than 1.4dB, the crosstalk is less than -50 dB.

  17. Mineral Liberation of Magnetite-Precipitated Copper Slag Obtained via Molten Oxidation by Using High-Voltage Electrical Pulses

    Science.gov (United States)

    Fan, Yong; Shibata, Etsuro; Iizuka, Atsushi; Nakamura, Takashi

    2016-10-01

    Our proposed method, i.e., a controlled molten oxidation process under 1 vol pct oxygen, leads to selective precipitation of magnetite in a copper smelter slag for downstream iron separation. In the present study, the preroasted magnetite precipitated copper slag was treated via magnetite liberation, which was realized by using high-voltage electrical pulses. The mineral distribution was determined by using a laser microscope and its image analysis; and it revealed that the 100- µm under-sieve product contains approximately 70 pct of liberated mineral particles. The study affirms the positive outcome of using this new technology for comminution to obtain micrometer-scale particles that yield monominerals via selective liberation. Using magnetic separation, iron was capable of finally separating into high- and low-iron-bearing concentrate and tailing that can be used in specific applications.

  18. The formation of diffuse discharge by short-front nanosecond voltage pulses and the modification of dielectrics in this discharge

    Science.gov (United States)

    Orlovskii, V. M.; Panarin, V. A.; Shulepov, M. A.

    2014-07-01

    The dynamics of diffuse discharge formation under the action of nanosecond voltage pulses with short fronts (below 1 ns) in the absence of a source of additional preionization and the influence of a dielectric film on this process have been studied. It is established that the diffuse discharge is induced by the avalanche multiplication of charge initiated by high-energy electrons and then maintained due to secondary breakdowns propagating via ionized gas channels. If a dielectric film (polyethylene, Lavsan, etc.) is placed on the anode, then multiply repeated discharge will lead to surface and bulk modification of the film material. Discharge-treated polyethylene film exhibits a change in the optical absorption spectrum in the near-IR range.

  19. Image processing for non-ratiometric measurement of membrane voltage using fluorescent reporters and pulsed laser illumination.

    Science.gov (United States)

    Silve, Aude; Rocke, Sarah; Frey, Wolfgang

    2015-06-01

    The measurement of transmembrane voltages induced by pulsed electric field exposure can be achieved by using fluorescent dyes like ANNINE-6. Such approach requires a quantitative determination of the fluorescence intensity along the cell's membrane by image processing. When high temporal resolution is required, the illumination source is frequently a dye-laser which causes high fluctuations in the intensity of illumination which in turn affects the fluorescence intensity and thus the quality of the results. We propose an image processing technique that allows to overcome the fluctuations and to produce quantitative data. It uses the optical background noise as a correcting factor. Standard deviation in the fluctuations is thus efficiently reduced by at least a factor of 2.5. Additionally we draw attention to the fact that the parasitic component of the laser radiation (ASE) can also suppress fluctuations although it deteriorates wavelength precision.

  20. Design and Experiments of the High Voltage Pulsed Electric Fields Sterilization System

    Institute of Scientific and Technical Information of China (English)

    ZHANG Xihai; FANG Junlong; SHEN Weizheng

    2008-01-01

    This experiment designed the pulsed electric fields (PEF) of high intensity of 100 kV. cml sterilization system. Fluorescent pseudomonas as target cell was operated 180 s in the PEF. By observing the difference of the bacteria before and after the disposal by TEM, it is found that the cell wails of the treated bacteria were broken. Irreversible perforations were formed on the cell membrane. The cell inclusions and cell fragments were leaked. The cell died as a result. The results showed that the PEF sterilization system designed can be used for liquid food sterilization experiments.

  1. DC link current simulation of voltage source inverter with random space vector pulse width modulation

    Directory of Open Access Journals (Sweden)

    Chen Guoqiang

    2016-01-01

    Full Text Available Aiming at analysis complexity, a simulation model is built and presented to analyze and demonstrate the characteristics of the direct current (DC link current of the three-phase two-level inverter with the random space vector pulse width modulation (SVPWM strategy. The developing procedure and key subsystems of the simulation model are given in detail. Several experiments are done using the simulation model. The results verify the efficiency and convenience of the simulation model and show that the random SVPWM scheme, especially the random switching frequency scheme, can efficiently suppress the harmonic peaks of the DC link current.

  2. Discharge ignition in the diaphragm configuration supplied by DC non-pulsing voltage

    Science.gov (United States)

    Hlochová, L.; Hlavatá, L.; Kozáková, Z.; Krčma, F.

    2016-05-01

    This work deals with the ignition of the discharge in the diaphragm configuration generated in water solutions containing supporting NaCl electrolyte. The reactor has volume of 110 ml and it is made of polycarbonate. HV electrodes made of stainless steel are placed in this reactor. Ceramic (Shapal-MTM) diaphragm is placed in the barrier separating the cathode and the anode space. An electric power source supplies the reactor by constant DC voltage up to 4 kV and electric current up to 300 mA. The discharge ignition is compared in the reactor with different sizes of diaphragms. Measurements are carried out in electrolyte solutions with the same conductivity. Images of plasma streamers and bubble formation are taken by an ICCD camera iStar 734. Electrical characteristics are measured by an oscilloscope LeCroy LT 374 L in order to determine breakdown moments at different experimental conditions.

  3. [Spectroscopic study on the high voltage fast pulsed discharge of nitrogen, ammonia or their mixture].

    Science.gov (United States)

    Liu, Z P; Wang, P N; Yang, W D; Zheng, J B; Li, F M

    2001-10-01

    The emission spectra from the pulsed discharge plasma of nitrogen, ammonia or their mixture were measured. In the discharge of pure nitrogen gas, as the pressure increased, the discharge volume decreased and more dissociation of nitrogen molecules occurred due to the higher energy density. In the discharge of ammonia, N,N+ and NH+ were observed, but no NH2 and NH3 were detected, indicating that ammonia, which has the lower dissociation and ionization energies as compared to nitrogen, was highly dissociated. The discharge of the mixture of N2 and NH3 was also studied. The dependence of the dissociation of nitrogen on the ratio of nitrogen to ammonia was investigated by emission spectra. The optimal ratio for nitrogen dissociation was obtained. The advantage of using the mixture of nitrogen and ammonia in the synthesis of nitrides was discussed.

  4. Degradation of Dye Wastewater by Pulsed High-Voltage Discharge Combined with Spent Tea Leaves

    Science.gov (United States)

    Liu, Yan; Yang, Li; Yang, Gang; Zhang, Yanzong; Zhang, Xiaohong; Deng, Shihuai

    2014-12-01

    Degradation of methylene blue (MB) was performed using the pulsed discharge process (PDP) combined with spent tea leaves (STLs). The effects of STL dosage, concentration of initial solution, and pH were analyzed in the combined treatment. Results showed that the combined treatment was effective for dye wastewater degradation; when the dosage of STLs was 3.2 g/L, the degradation efficiency reached 90% after 15 min treatment, and STLs showed a good repeatability. The degradation rate decreased with increasing initial MB concentration but not related to the solution pH in the combined treatment. Fourier-transform infrared spectra and N2 adsorption suggested that the number of acidic and basic groups in the STL surface increased after the treatment, but the surface area and pore volume remained unchanged.

  5. Soft x-ray generation in gases by means of a pulsed electron beam produced in a high-voltage barier discharge

    NARCIS (Netherlands)

    Azarov, A.V.; Peters, P.J.M.; Boller, K.-J.

    2007-01-01

    A large area pulsed electron beam is produced by a high-voltage barrier discharge. We compare the properties of the x-rays generated by stopping this beam of electrons in a thin metal foil with those generated by stopping the electrons directly in various gases. The generation of x-rays was investig

  6. Theory of quantum transport in disordered systems driven by voltage pulse

    Science.gov (United States)

    Zhou, Chenyi; Chen, Xiaobin; Guo, Hong

    2016-08-01

    Predicting time-dependent quantum transport in the transient regime is important for understanding the intrinsic dynamic response of a nanodevice and for predicting the limit of how such a device can switch on or off a current. Theoretically, this problem becomes quite difficult to solve when the nanodevice contains disorder because the calculated transient current must be averaged over many disorder configurations. In this work, we present a theoretical formalism to calculate the configuration averaged time-dependent current flowing through a phase coherent device containing disorder sites where the transient current is driven by sharply turning on and off the external bias voltage. Our theory is based on the Keldysh nonequilibrium Green's function (NEGF) formalism and is applicable in the far from equilibrium nonlinear response quantum transport regime. The effects of disorder scattering are dealt with by the coherent potential approximation (CPA) extended in the time domain. We show that after approximations such as CPA and vertex corrections for calculating the multiple impurity scattering in the transient regime, the derived NEGFs perfectly satisfy a Ward identity. The theory is quantitatively verified by comparing its predictions to the exact solution for a tight-binding model of a disordered two-probe transport junction.

  7. Optical fiber imaging for high speed plasma motion diagnostics: applied to low voltage circuit breakers.

    Science.gov (United States)

    McBride, J W; Balestrero, A; Ghezzi, L; Tribulato, G; Cross, K J

    2010-05-01

    An integrated portable measurement system is described for the study of high speed and high temperature unsteady plasma flows such as those found in the vicinity of high current switching arcs. An array of optical fibers allows the formation of low spatial resolution images, with a maximum capture rate of 1 x 10(6) images per second (1 MHz), with 8 bit intensity resolution. Novel software techniques are reported to allow imaging of the arc; and to measure arc trajectories. Results are presented on high current (2 kA) discharge events in a model test fixture and on the application to a commercial low voltage circuit breaker.

  8. Avalanche mode of high-voltage overloaded p{sup +}–i–n{sup +} diode switching to the conductive state by pulsed illumination

    Energy Technology Data Exchange (ETDEWEB)

    Kyuregyan, A. S., E-mail: ask@vei.ru [Lenin All-Russia Electrical Engineering Institute (Russian Federation)

    2015-07-15

    A simple analytical theory of the picosecond switching of high-voltage overloaded p{sup +}–i–n{sup +} photodiodes to the conductive state by pulsed illumination is presented. The relations between the parameters of structure, light pulse, external circuit, and main process characteristics, i.e., the amplitude of the active load current pulse, delay time, and switching duration, are derived and confirmed by numerical simulation. It is shown that the picosecond light pulse energy required for efficient switching can be decreased by 6–7 orders of magnitude due to the intense avalanche multiplication of electrons and holes. This offers the possibility of using pulsed semiconductor lasers as a control element of optron pairs.

  9. Performance of a semi-pilot tubular microbial electrolysis cell (MEC) under several hydraulic retention times and applied voltages.

    Science.gov (United States)

    Gil-Carrera, L; Escapa, A; Carracedo, B; Morán, A; Gómez, X

    2013-10-01

    The influence of applied voltage and hydraulic retention time on the performance of a semi-pilot modular tubular wastewater-fed microbial electrolysis cell (MEC) with high scalability was investigated. A chemical oxygen demand (COD) removal efficiency of 80%, as well as an energy consumption of 0.3-1.1 Wh g-COD(-1) removed, were achieved. Hydrogen production was limited by the reduced amounts of organic matter fed into the reactor, the poor performance of the cathode, and COD consuming by non electrogenic microorganisms. The presence of COD consuming microorganism that do not contribute to electrogenic metabolism severely affected the MEC performance.

  10. Characteristics of plasma in culture medium generated by positive pulse voltage and effects of organic compounds on its characteristics

    Science.gov (United States)

    Sato, Y.; Sato, T.; Yoshino, D.

    2016-12-01

    We describe a positive pulse voltage method for generating plasma in culture medium with a composition similar to biological fluids. We also describe the plasma’s characteristics, liquid quality, and the effect of organic compounds in the culture medium on the plasma characteristics through comparisons to a solution containing inorganic salts at the same concentrations as in the culture medium. Light emission with Na and OH spectra was observed within a vapor bubble produced by Joule heating at the tip of the electrode. A downward thermal flow and shock wave were caused by the behavior of the vapor bubble. The culture medium pH gradually increased from 7.9 to 8.3 over the discharge time of 300 s. H2O2 was generated 1.1 mg l-1 in the culture medium after discharge for 300 s, and this value was 0.5 mg l-1 lower than the inorganic salts solution which does not contain organic compounds. This study provides important data that will help facilitate more widespread application of plasma medicine.

  11. Mechanism of Fast Current Interruption in p -π -n Diodes for Nanosecond Opening Switches in High-Voltage-Pulse Applications

    Science.gov (United States)

    Sharabani, Y.; Rosenwaks, Y.; Eger, D.

    2015-07-01

    Step-recovery diodes operating in the snappy recovery regime are used as opening switches for generating narrow pulses with high-voltage amplitude. Physical modeling of the switching process is complex due to the large number of parameters involved, including diode structure, the extreme physical conditions, and the effect of external driving conditions. In this work, we address the problem by using a physical device simulator for solving the coupled device and electrical driving circuit equations. This method allows deciphering of the physical processes to take place in the diode during the fast current interruption phase. Herein we analyze the complete hard (snappy) reverse recovery process in short-base devices and determine the fast-transition-phase mechanism. It was found that the fast current interruption phase is constructed of two processes; the main parameters governing the switching time duration and the prepulse magnitude are the diode's reverse current density and its base-doping concentration. We describe the dependence of the switching performance in these parameters.

  12. Signal enhancement in collinear double-pulse laser-induced breakdown spectroscopy applied to different soils

    Energy Technology Data Exchange (ETDEWEB)

    Nicolodelli, Gustavo, E-mail: gunicolodelli@hotmail.com [Embrapa Instrumentation, Rua XV de Novembro, 1452, CEP 13560-970 São Carlos, SP (Brazil); Senesi, Giorgio Saverio, E-mail: giorgio.senesi@imip.cnr.it [Institute of Inorganic Methodologies and Plasmas, CNR, Bari, 70126 Bari (Italy); Romano, Renan Arnon, E-mail: renan.romano@gmail.com [Embrapa Instrumentation, Rua XV de Novembro, 1452, CEP 13560-970 São Carlos, SP (Brazil); Physics Institute of São Carlos, University of São Paulo, IFSC-USP, Av. Trabalhador são-carlense, 400 Pq. Arnold Schimid, 13566-590 São Carlos, SP (Brazil); Oliveira Perazzoli, Ivan Luiz de, E-mail: ivanperazzoli@hotmail.com [Embrapa Instrumentation, Rua XV de Novembro, 1452, CEP 13560-970 São Carlos, SP (Brazil); Milori, Débora Marcondes Bastos Pereira, E-mail: debora.milori@embrapa.br [Embrapa Instrumentation, Rua XV de Novembro, 1452, CEP 13560-970 São Carlos, SP (Brazil)

    2015-09-01

    Laser-induced breakdown spectroscopy (LIBS) is a well-known consolidated analytical technique employed successfully for the qualitative and quantitative analysis of solid, liquid, gaseous and aerosol samples of very different nature and origin. Several techniques, such as dual-pulse excitation setup, have been used in order to improve LIBS's sensitivity. The purpose of this paper was to optimize the key parameters as excitation wavelength, delay time and interpulse, that influence the double pulse (DP) LIBS technique in the collinear beam geometry when applied to the analysis at atmospheric air pressure of soil samples of different origin and texture from extreme regions of Brazil. Additionally, a comparative study between conventional single pulse (SP) LIBS and DP LIBS was performed. An optimization of DP LIBS system, choosing the correct delay time between the two pulses, was performed allowing its use for different soil types and the use of different emission lines. In general, the collinear DP LIBS system improved the analytical performances of the technique by enhancing the intensity of emission lines of some elements up to about 5 times, when compared with conventional SP-LIBS, and reduced the continuum emission. Further, the IR laser provided the best performance in re-heating the plasma. - Highlights: • The correct choice of the delay time between the two pulses is crucial for the DP system. • An optimization of DP LIBS system was performed allowing its use for different soil and the use of different emission lines. • The DP LIBS system improved the analytical performances of the technique up to about 5 times, when compared with SP LIBS. • The IR laser provided the best performance in re-heating the plasma.

  13. Enhanced analogue front-end for the measurement of the high state of wide-band voltage pulses with 87 dB common-mode rejection ratio and ±0.65 ppm 1-day offset stability

    Science.gov (United States)

    Arpaia, Pasquale; Baccigalupi, Carlo; Martino, Michele

    2015-09-01

    An improved analogue front-end for measuring the high state of trapezoidal voltage pulses with transition duration of 3 μs is presented. A new measurement system, composed by a front-end and the state-of-the-art acquisition board NI PXI-5922, has been realized with improved Common Mode Rejection Ratio (CMRR) of more than 87 dB at DC and 3-sigma stability of ±0.65 ppm over 1 day. After highlighting the main design enhancements with respect to state-of-the-art solutions, the CMRR measurement is reported. The output drift due to temperature and humidity is assessed to be negligible. Finally, the worst-case repeatability is measured both with shorted-to-ground inputs and with an applied common-mode voltage of 10 V, which represents the nominal working condition.

  14. Enhanced analogue front-end for the measurement of the high state of wide-band voltage pulses with 87 dB common-mode rejection ratio and ±0.65 ppm 1-day offset stability

    CERN Document Server

    AUTHOR|(SzGeCERN)712364; Arpaia, Pasquale; Martino, Michele

    2015-01-01

    An improved analogue front-end for measuring the high state of trapezoidal voltage pulses with transition duration of 3 μs is presented. A new measurement system, composed by a front-end and the state-of-the-art acquisition board NI PXI-5922, has been realized with improved Common Mode Rejection Ratio (CMRR) of more than 87 dB at DC and 3-sigma stability of }0.65 ppm over 1 day. After highlighting the main design enhancements with respect to state-of-the-art solutions, the CMRR measurement is reported. The output drift due to temperature and humidity is assessed to be negligible. Finally, the worst-case repeatability is measured both with shorted-to-ground inputs and with an applied common-mode voltage of 10 V, which represents the nominal working condition.

  15. 基于TTL数字电路控制的高压脉冲源%High-voltage pulse source controlled by TTL digital circuit

    Institute of Scientific and Technical Information of China (English)

    李玺钦; 丁明军; 吴红光; 冯莉; 刘云涛; 戴文峰; 黄雷

    2012-01-01

    给出了一种基于TTL数字电路作为高压脉冲源触发控制单元的设计原理和方法.介绍了高压脉冲源的工作原理,设计了一台脉冲输出幅度5 kV、脉冲宽度大于200 μs及脉冲前沿小于30 ns的高压脉冲源.将触发控制单元和前级开关金属氧化物半导体场效应管(MOSFET)组合成一体,控制后级气体高压开关管放电输出高压脉冲信号.实验结果验证了所采用的设计原理及方法的可行性,给出了单次触发情况下的实验结果.%The paper introduces a TTL digital circuit, which is designed as the trigger control system of high power pulse source, and presents the development of a high-voltage pulse source. In the source, the TTL circuit operated after the optical isolation circuit and power driver, and outputs pulse signals to drive MOSFET, which controls the pulse signal output from high-voltage switch. The source can outputs pulses with voltage of 5 kV, pulse-width larger than 200 Ωs and fall-time less than 30 ns. Besides long-distance control and local control mode, it also includes inner trigger and external trigger (one electric signal and one optical signal as the trigger). A series of experiments have been conducted to validate the design, and the one-shot trigger results are presented.

  16. THE EFFECTS OF PULSE BIAS VOLTAGE AND N2 PARTIAL PRESSURE ON TiAIN FILMS OF ARC ION PLATING (AIP)

    Institute of Scientific and Technical Information of China (English)

    M.S. Li; S.L. Zhu; Fuhui Wang; C. Sun; L.S. Wen

    2001-01-01

    Owing to the characteristics of arc ion plating(AIP) technique, the structure and com-position of TiAlN films can be tailored by controlling of various parameters such ascompositions of target materials, N2 partial pressure, substrate bias and so on. ln thisstudy, several titanium aluminum nitride films were deposited on 1Cr11Ni2 W2Mo Vsteel for compressor blade of areo-engine under different d.c pulse bias voltage and ni-trogen partial pressure. The effects of substrate pulse bias and nitrogen partial pressureon the deposition rate, droplet formation, microstruture and elemental component ofthe films were investigated.

  17. Influence of Applied Bias Voltage on the Composition, Structure, and Properties of Ti:Si-Codoped a-C:H Films Prepared by Magnetron Sputtering

    Directory of Open Access Journals (Sweden)

    Jinlong Jiang

    2014-01-01

    Full Text Available The titanium- and silicon-codoped a-C:H films were prepared at different applied bias voltage by magnetron sputtering TiSi target in argon and methane mixture atmosphere. The influence of the applied bias voltage on the composition, surface morphology, structure, and mechanical properties of the films was investigated by XPS, AFM, Raman, FTIR spectroscopy, and nanoindenter. The tribological properties of the films were characterized on an UMT-2MT tribometer. The results demonstrated that the film became smoother and denser with increasing the applied bias voltage up to −200 V, whereas surface roughness increased due to the enhancement of ion bombardment as the applied bias voltage further increased. The sp3 carbon fraction in the films monotonously decreased with increasing the applied bias voltage. The film exhibited moderate hardness and the superior tribological properties at the applied bias voltage of −100 V. The tribological behaviors are correlated to the H/E or H3/E2 ratio of the films.

  18. Design and measurements of a fast high-voltage pulse generator for the MedAustron Low Energy Transfer line fast deflector

    CERN Document Server

    Fowler, T; Mueller, F; Kramer, T; Stadlbauer, T

    2012-01-01

    MedAustron, a centre for ion-therapy and research, will comprise an accelerator facility based on a synchrotron for the delivery of protons and light ions for cancer treatment. The Low Energy Beam Transfer line (LEBT) to the synchrotron contains an electrostatic fast deflector (EFE) which, when energized, deviates the continuous beam arriving from the ion source onto a Faraday Cup: the specified voltage is ±3.5 kV. De-energizing the EFE for variable pulse durations from 500 ns up to d.c. allows beam passage for multi-turn injection into the synchrotron. To maintain beam quality in the synchrotron, the EFE pulse generator requires rise and fall times of less than 300 ns between 90 % of peak voltage and a ±1 V level. To achieve this, a pulsed power supply (PKF), with high voltage MOSFET switches connected in a push-pull configuration, will be mounted in close proximity to the deflector itself. A fast, large dynamic range monitoring circuit will verify switching to the ±1 V level and subsequent flat bottom pu...

  19. Optical and Electrical Performance of MOS-Structure Silicon Solar Cells with Antireflective Transparent ITO and Plasmonic Indium Nanoparticles under Applied Bias Voltage

    Directory of Open Access Journals (Sweden)

    Wen-Jeng Ho

    2016-08-01

    Full Text Available This paper reports impressive improvements in the optical and electrical performance of metal-oxide-semiconductor (MOS-structure silicon solar cells through the incorporation of plasmonic indium nanoparticles (In-NPs and an indium-tin-oxide (ITO electrode with periodic holes (perforations under applied bias voltage. Samples were prepared using a plain ITO electrode or perforated ITO electrode with and without In-NPs. The samples were characterized according to optical reflectance, dark current voltage, induced capacitance voltage, external quantum efficiency, and photovoltaic current voltage. Our results indicate that induced capacitance voltage and photovoltaic current voltage both depend on bias voltage, regardless of the type of ITO electrode. Under a bias voltage of 4.0 V, MOS cells with perforated ITO and plain ITO, respectively, presented conversion efficiencies of 17.53% and 15.80%. Under a bias voltage of 4.0 V, the inclusion of In-NPs increased the efficiency of cells with perforated ITO and plain ITO to 17.80% and 16.87%, respectively.

  20. Optical and Electrical Performance of MOS-Structure Silicon Solar Cells with Antireflective Transparent ITO and Plasmonic Indium Nanoparticles under Applied Bias Voltage.

    Science.gov (United States)

    Ho, Wen-Jeng; Sue, Ruei-Siang; Lin, Jian-Cheng; Syu, Hong-Jang; Lin, Ching-Fuh

    2016-08-10

    This paper reports impressive improvements in the optical and electrical performance of metal-oxide-semiconductor (MOS)-structure silicon solar cells through the incorporation of plasmonic indium nanoparticles (In-NPs) and an indium-tin-oxide (ITO) electrode with periodic holes (perforations) under applied bias voltage. Samples were prepared using a plain ITO electrode or perforated ITO electrode with and without In-NPs. The samples were characterized according to optical reflectance, dark current voltage, induced capacitance voltage, external quantum efficiency, and photovoltaic current voltage. Our results indicate that induced capacitance voltage and photovoltaic current voltage both depend on bias voltage, regardless of the type of ITO electrode. Under a bias voltage of 4.0 V, MOS cells with perforated ITO and plain ITO, respectively, presented conversion efficiencies of 17.53% and 15.80%. Under a bias voltage of 4.0 V, the inclusion of In-NPs increased the efficiency of cells with perforated ITO and plain ITO to 17.80% and 16.87%, respectively.

  1. Pulse

    Science.gov (United States)

    ... resting for at least 10 minutes. Take the exercise heart rate while you are exercising. ... pulse rate can help determine if the person's heart is pumping. Pulse ... rate gives information about your fitness level and health.

  2. A microbial fuel cell with the three-dimensional electrode applied an external voltage for synthesis of hydrogen peroxide from organic matter

    Science.gov (United States)

    Chen, Jia-yi; Zhao, Lin; Li, Nan; Liu, Hang

    2015-08-01

    The study experimentally investigates the changing performance of three-dimensional electrode H2O2-producting MFCs coupled with simultaneous wastewater treatment at various external cell voltages from 0.1 V to 0.8 V, in order to explore the optimal applied voltage and its reasons. The graphite particle electrodes made of graphite powders with polytetrafluoroethene (PTFE) as the binder are used as three-dimensional cathode. The results indicate that applied voltage is demonstrated to increase the productive rate and output of H2O2 and the efficiency of acetate degradation. Besides, a relatively high current density caused by a high applied voltage has a positive impact on anode performance in terms of organic degradation and coulombic efficiency. In addition, a relatively high voltage leads to the reduction of H2O2 and the evolution of H2. Considering H2O2 concentration, anodic COD removal and current efficiencies of MFCs at various voltages, the optimal voltage is chosen to be 0.4 V, achieving the H2O2 generation of 705.6 mg L-1 at a rate of 2.12 kg m-3 day-1 and 76% COD removal in 8 h, with energy input of 0.659 kWh per kg H2O2. Coulombic efficiency, faradic efficiency and COD conversion efficiency are 92%, 96%, and 88% respectively.

  3. Investigation on a Novel Discontinuous Pulse-Width Modulation Algorithm for Single-phase Voltage Source Rectifier

    DEFF Research Database (Denmark)

    Qu, Hao; Yang, Xijun; Guo, Yougui

    2014-01-01

    -sequence component injection, in order to reduce power loss and increased overall efficiency. And then by reconstructing the other two phase input voltages and currents, the transformation from stationary frame (abc) to rotating frame (dq frame) is designed. Finally, a PI regulator based controller for single......Single-phase voltage source converter (VSC) is an important power electronic converter (PEC), including single-phase voltage source inverter (VSI), single-phase voltage source rectifier (VSR), single-phase active power filter (APF) and single-phase grid-connection inverter (GCI). Single-phase VSC...

  4. High-temperature performance of MoS{sub 2} thin-film transistors: Direct current and pulse current-voltage characteristics

    Energy Technology Data Exchange (ETDEWEB)

    Jiang, C.; Samnakay, R.; Balandin, A. A., E-mail: balandin@ee.ucr.edu [Nano-Device Laboratory (NDL), Department of Electrical Engineering, Bourns College of Engineering, University of California—Riverside, Riverside, California 92521 (United States); Phonon Optimized Engineered Materials (POEM) Center, Materials Science and Engineering Program, University of California—Riverside, Riverside, California 92521 (United States); Rumyantsev, S. L. [Department of Electrical, Computer, and Systems Engineering, Center for Integrated Electronics, Rensselaer Polytechnic Institute, Troy, New York 12180 (United States); Ioffe Physical-Technical Institute, St. Petersburg 194021 (Russian Federation); Shur, M. S. [Department of Electrical, Computer, and Systems Engineering, Center for Integrated Electronics, Rensselaer Polytechnic Institute, Troy, New York 12180 (United States)

    2015-02-14

    We report on fabrication of MoS{sub 2} thin-film transistors (TFTs) and experimental investigations of their high-temperature current-voltage characteristics. The measurements show that MoS{sub 2} devices remain functional to temperatures of at least as high as 500 K. The temperature increase results in decreased threshold voltage and mobility. The comparison of the direct current (DC) and pulse measurements shows that the direct current sub-linear and super-linear output characteristics of MoS{sub 2} thin-films devices result from the Joule heating and the interplay of the threshold voltage and mobility temperature dependences. At temperatures above 450 K, a kink in the drain current occurs at zero gate voltage irrespective of the threshold voltage value. This intriguing phenomenon, referred to as a “memory step,” was attributed to the slow relaxation processes in thin films similar to those in graphene and electron glasses. The fabricated MoS{sub 2} thin-film transistors demonstrated stable operation after two months of aging. The obtained results suggest new applications for MoS{sub 2} thin-film transistors in extreme-temperature electronics and sensors.

  5. Breakdown voltage of metal-oxide resistors in liquid argon

    CERN Document Server

    Bagby, L F; James, C C; Jones, B J P; Jostlein, H; Lockwitz, S; Naples, D; Raaf, J L; Rameika, R; Schukraft, A; Strauss, T; Weber, M S; Wolbers, S A

    2014-01-01

    We characterized a sample of metal-oxide resistors and measured their breakdown voltage in liquid argon by applying high voltage (HV) pulses over a 3 second period to simulate the electric breakdown in a HV-divider chain. All resistors had higher breakdown voltages in liquid argon than their vendor ratings in air at room temperature. Failure modes range from full destruction to coating damage. In cases where breakdown was not catastrophic, subsequent breakdown voltages were lower in subsequent measuring runs. One resistor type withstands 131\\,kV pulses, the limit of the test setup.

  6. 高强脉冲电场与臭氧联用降解壳聚糖%Degradation of chitosan by high voltage pulsed electric field and ozone

    Institute of Scientific and Technical Information of China (English)

    罗文波; 唐超; 曾新安; 于淑娟

    2013-01-01

    The vigorous oxidation ability of ozone and the high energy input of pulsed electric field were utilized to degrade the macromolecular chitosan to oligochitosan. The degradation rate was up to 98. 5% after the combined treatment of high voltage pulsed electric field and ozone for 30 minutes in acetic acid homogeneous phase. Three experiment schemes of individual and combined treatments of high voltage pulsed electric field and ozone were designed the results showed that the efficiency of combined treatment was higher than that of single treatments, so the combination of high voltage pulsed electric field and ozone had high synergistic effect. By infrared spectrum analysis, the structure of degraded chitosan was not changed compared to the initial chitosan.%利用臭氧的强氧化性和电场的高能量降解大分子壳聚糖为壳寡糖.在乙酸均相体系中,高强脉冲电场与臭氧联用处理壳聚糖30min时,壳聚糖的降解率达到98.5%.设计了脉冲电场、臭氧单独处理和电场与臭氧联用处理3种实验方案,结果表明:电场与臭氧联用的处理效率要高于分别处理效率,电场与臭氧联用具有协同作用.经红外光谱分析,降解产物与原料壳聚糖结构基本一致.

  7. Energy Efficiency of Induction Motors Running Off Frequency Converters with Pulse-Width Voltage Modulation{sup 1}

    Energy Technology Data Exchange (ETDEWEB)

    Shvetsov, N. K., E-mail: elmash@em.ispu.ru [V. I. Lenin Ivanovo State Power University (Russian Federation)

    2016-11-15

    The results of calculations of the increase in losses in an induction motor with frequency control and different forms of the supply voltage are presented. The calculations were performed by an analytic method based on harmonic analysis of the supply voltage as well as numerical calculation of the electromagnetic processes by the finite-element method.

  8. Research of manufacturing high voltage nanosecond electromagnetic pulse attenuator%高压纳秒电磁脉冲衰减器的研制

    Institute of Scientific and Technical Information of China (English)

    陈炜峰; 宋珂锦

    2012-01-01

    随着电磁脉冲技术的发展,电磁脉冲前沿越来越快,峰值越来越高.针对这些特点,为了减小高压纳秒电磁脉冲传输、衰减过程中电磁波的反射,在输出端得到理想的电磁脉冲波形,设计了一种高压纳秒电磁脉冲衰减器,采用高频电磁场仿真软件HFSS建模仿真,分析驻波比,优化结构尺寸.根据仿真及优化结果,制作了衰减量为30%和40%的衰减器样机.实验表明样机衰减量误差小,传输性能好,可对上升时间2 ns左右,峰值小于40 kV的电磁脉冲实现有效衰减.%With the development of technology of electromagnetic pulse, the rising of electromagnetic pulse is more and more quickly, the peak is higher and higher. According to these characteristics, in order to reduce the reflex of high voltage nanosecond electromagnetic pulse in transmission and attenuation which can output the ideal electromagnetic pulse waveform, design of a high voltage nanosecond electromagnetic pulse attenuator, using high-frequency electromagnetic simulation software HFSS modeling,the size of the structure was optimized base on simulation,and got the simulation of VSWR (voltage standing wave ratio). According to the simulation and structural optimization of results,making attenuation for 30% and 40% of the attenuator prototype. Experimental validation of a prototype performance good, .deviation small,the attenuator had effective attenuation on the electromagnetic pulse which riseing time is about 2 ns,peak of pulse is less than 40 kV.

  9. Effect of applied voltage on surface properties of anodised titanium in mixture of β-glycerophosphate (β-GP) and calcium acetate (CA)

    Energy Technology Data Exchange (ETDEWEB)

    Chuan, Lee Te, E-mail: gd130079@siswa.uthm.edu.my; Rathi, Muhammad Fareez Mohamad, E-mail: cd110238@siswa.uthm.edu.my; Abidin, Muhamad Yusuf Zainal, E-mail: cd110221@siswa.uthm.edu.my; Abdullah, Hasan Zuhudi, E-mail: hasan@uthm.edu.my; Idris, Maizlinda Izwana, E-mail: izwana@uthm.edu.my [Faculty of Mechanical and Manufacturing Engineering, Universiti Tun Hussein Onn Malaysia, 86400 Parit Raja, Batu Pahat, Johor (Malaysia)

    2015-07-22

    Anodic oxidation is a surface modification method which combines electric field driven metal and oxygen ion diffusion for formation of oxide layer on the anode surface. This method has been widely used to modify the surface morphology of biomaterial especially titanium. This study aimed to investigate the effect of applied voltage on titanium. Specifically, the titanium foil was anodised in mixture of β-glycerophosphate disodium salt pentahydrate (β-GP) and calcium acetate monohydrate (CA) with different applied voltage (50-350 V), electrolyte concentration (0.04 M β-GP + 0.4 M CA), anodising time (10minutes) and current density (50 and 70 mA.cm{sup −2}) at room temperature. Surface oxide properties of anodised titanium were characterised by digital single-lens reflex camera (DSLR camera), field emission scanning electron microscope (FESEM) and atomic force microscopy (AFM). At lower applied voltage (≤150 V), surface of titanium foils were relatively smooth. With increasing applied voltage (≥250 V), the oxide layer became more porous and donut-shaped pores were formed on the surface of titanium foils. The AFM results indicated that the surface roughness of anodised titanium increases with increasing of applied voltage. The porous and rough surface is able to promote the osseointegration and reduce the suffering time of patient.

  10. The Pulse Line Ion Accelerator Concept

    Energy Technology Data Exchange (ETDEWEB)

    Briggs, Richard J.

    2006-02-15

    The Pulse Line Ion Accelerator concept was motivated by the desire for an inexpensive way to accelerate intense short pulse heavy ion beams to regimes of interest for studies of High Energy Density Physics and Warm Dense Matter. A pulse power driver applied at one end of a helical pulse line creates a traveling wave pulse that accelerates and axially confines the heavy ion beam pulse. Acceleration scenarios with constant parameter helical lines are described which result in output energies of a single stage much larger than the several hundred kilovolt peak voltages on the line, with a goal of 3-5 MeV/meter acceleration gradients. The concept might be described crudely as an ''air core'' induction linac where the PFN is integrated into the beam line so the accelerating voltage pulse can move along with the ions to get voltage multiplication.

  11. Quality Assessment of Soft-Switching Based Single-phase Pulse Width Modulated Voltage Source Inverter (PWM VSI

    Directory of Open Access Journals (Sweden)

    Z.A. Jaffery

    2012-10-01

    Full Text Available The authors present the design, simulation and analysis of a single phase voltage source inverter using soft switching techniques. The performance of the inverter has been compared in terms of harmonic contents present in output voltage and current. The research works for a PWM inverter along with a LLCC filter has been investigated. This paper also investigated the performance of the same inverter with a feedback controller with a closed loop feedback path to maintain rated output voltage. This work is helpful for the inverter used in application where high quality ac wave is prime requirement

  12. Photoelectrocatalytic decomposition of ethylene using TiO{sub 2}/activated carbon fiber electrode with applied pulsed direct current square-wave potential

    Energy Technology Data Exchange (ETDEWEB)

    Ye, Sheng-ying, E-mail: yesy@scau.edu.cn; Zheng, Sen-hong; Song, Xian-liang; Luo, Shu-can

    2015-06-30

    Highlights: • Ethylene was decomposed by a photoelectrocatalytic (PEC) process. • A pulsed direct current square-wave (PDCSW) potential was applied to the PEC cell. • An electrode of TiO{sub 2} or modified TiO{sub 2} and activated carbon fiber (ACF) was used. • TiO{sub 2}/ACF photocatalyst electrodes were modified by gamma radiolysis. • Efficiencies of the PEC process were higher than those of the process using DC. - Abstract: Removing ethylene (C{sub 2}H{sub 4}) from the atmosphere of storage facilities for fruits and vegetable is one of the main challenges in their postharvest handling for maximizing their freshness, quality, and shelf life. In this study, we investigated the photoelectrocatalytic (PEC) degradation of ethylene gas by applying a pulsed direct current DC square-wave (PDCSW) potential and by using a Nafion-based PEC cell. The cell utilized a titanium dioxide (TiO{sub 2}) photocatalyst or γ-irradiated TiO{sub 2} (TiO{sub 2}{sup *}) loaded on activated carbon fiber (ACF) as a photoelectrode. The apparent rate constant of a pseudo-first-order reaction (K) was used to describe the PEC degradation of ethylene. Parameters of the potential applied to the PEC cell in a reactor that affect the degradation efficiency in terms of the K value were studied. These parameters were frequency, duty cycle, and voltage. Ethylene degradation by application of a constant PDCSW potential to the PEC electrode of either TiO{sub 2}/ACF cell or TiO{sub 2}{sup *}/ACF cell enhanced the efficiency of photocatalytic degradation and PEC degradation. Gamma irradiation of TiO{sub 2} in the electrode and the applied PDCSW potential synergistically increased the K value. Independent variables (frequency, duty cycle, and voltage) of the PEC cell fabricated from TiO{sub 2} subjected 20 kGy γ radiation were optimized to maximize the K value by using response surface methodology with quadratic rotation–orthogonal composite experimental design. Optimized conditions were as

  13. [Research progress of nanosecond pulsed electric field applied to intracellular electromanipulation].

    Science.gov (United States)

    Yao, Chenguo; Mo, Dengbin; Sun, Caixin; Chen, Xin; Xiong, Zheng'ai

    2008-10-01

    In recent years, many experts have done some researches on experiment and mechanism of intracellular electromanipulation (IEM) under nanosecond pulsed electric field (nsPEF). The experiment results have shown that nsPEF could not induce electroporation of cell membrane, but could induce intracellular effects such as apoptosis, calcium release, enhancement of gene expression, and fragmentation of DNA and chromosome. In order to account for the phenomenon, researchers believe that when the pulse width of the pulsed electric field is larger than the charging time of plasma membrane, the pulsed electric field mainly targets on the outer membrane of cell; and that the effect of the pulsed electric field on nucleus and nuclear membrane increases with the decrease of the pulse width. It is also believed that the effect of electroporation changes from the outer membrane to intracellular electromanipulation when the pulse width decreases to a value being smaller than the charging time of plasma membrane.

  14. Modeling of the Partial Discharge Process in a Liquid Dielectric: Effect of Applied Voltage, Gap Distance, and Electrode Type

    Directory of Open Access Journals (Sweden)

    Tao Yuan

    2013-02-01

    Full Text Available The partial discharge (PD process in liquid dielectrics is influenced by several factors. Although the PD current contains the information representing the discharge process during the PD event, it is difficult to determine the detailed dynamics of what is happening in the bulk of the liquid. In this paper, a microscopic model describing the dynamics of the charge carriers is implemented. The model consists of drift-diffusion equations of electrons, positive and negative ions coupled with Poisson’s equation. The stochastic feature of PD events is included in the equation. First the model is validated through comparison between the calculated PD current and experimental data. Then experiments are conducted to study the effects of the amplitude of the applied voltage, gap distance and electrode type on the PD process. The PD currents under each condition are recorded. Simulations based on the model have been conducted to analyze the dynamics of the PD events under each condition, and thus explain the mechanism of how these factors influence the PD events. The space charge generated in the PD process is revealed as the main reason affecting the microscopic process of the PD events.

  15. 用于等离子体离子辐照的新型阶梯型脉冲高压电路研制%Novel Circuit Producing Pulsed High Voltage with Discrete Steps for Ion Bombardment in Plasma Immersion

    Institute of Scientific and Technical Information of China (English)

    石经纬; 田修波; 巩春志; 杨士勤

    2011-01-01

    为满足等离子体离子辐照和复合表面改性处理技术的发展,提出了基于Marx发生器,通过调节驱动信号延时,实现放电IGBT开关不同时导通,从而获得阶梯型脉冲高压输出的电路设计思想,并验证了其可行性.试验结果显示,该电路可输出脉冲峰值电压10 kV,峰值电流30 A,脉冲宽度3~30μs,脉冲频率20~500 Hz,最大电压阶数10阶的高压脉冲.1个原边、10个副边结构的驱动高压隔离变压器及延时驱动电路结构紧凑,抗干扰能力强.IGBT驱动反向偏置脉冲电压能够满足IGBT快速关断和过流保护的要求.等离子体负载下电路特性测试结果表明,该电路能够适应实际的工作环境,为复合处理技术的发展提供技术支持.该电路结构通过Marx单元叠加可以拓展到更高的脉冲电压输出.%A novel circuit which is capable of producing pulsed high voltage with discrete steps based on Marx generator has been developed for ion bombardment in plasma immersion, and it is realized by means of each discharge IG-BT switching on at different time by adjusting the delay time of drive signals. A compact and robust circuit is designed, using a high-voltage isolation transformer with one primary winding and ten secondary windings for control signal and designed delay drive unit, to meet the requirements of rapidity of switch off and overcurrent protection of IGBT. A pulsed high voltage with amplitude of 10kV, peak current of 30A, pulse width of 3~30 μs, frequency of 20~500 Hz and voltage steps of 10 are achieved. The developed circuit with several kinds of output voltage waveforms is applied to the plasma load with high reliability, and possesses the practicability for ion bombardment or hy-. Brid surface modification in plasma immersion mode. The higher pulse voltage may be achieved using more Marx link with the same control mode for wide application.

  16. 外部电压源法测试大电压LED器件/模块热阻%Measuring thermal resistance for high voltage LED device and module by applying ex ternal voltage source

    Institute of Scientific and Technical Information of China (English)

    陈国龙; 朱丽虹; 郭自泉; 张纪红; 吕毅军; 高玉琳; 陈忠

    2013-01-01

    热阻是衡量LED器件/模块散热性能的重要参数。针对大电压LED器件/模块,实验采用 T3Ster/T eraled热光参数测试仪,利用外部电压源供电方法,实现了对超过仪器量程的大电压L ED器件的热阻测试。该方法拓展了热阻测试仪的常规测量范围,使正向电压大于15 V的L ED器件/模块的热阻测试成为可能。%Thermal resistance is a key parameter for evaluating thermal performance of LED device/module . Reliable measurement of thermal resistance becomes extremely important .Aiming at that the high voltage LED device/module has been applied popularly in lighting ,an improved thermal resistance measurement method for LED device/module with forward voltage larger than 15V is achieved by applying external voltage source to the T3Ster/Teraled .The result shows that the external voltage source method can effectively expand the testing range of thermal resistance tester .

  17. Propagation of terawatt-femtosecond laser pulses and its application to the triggering and guiding of high-voltage discharges

    OpenAIRE

    Ackermann, Roland

    2006-01-01

    When an ultrashort-terawatt laser pulse is propagating through the atmosphere, long filaments may develop. Their light is confined in an area of about 100 µm over distances up to several hundred meters, and an air plasma is generated along the beam path. Moreover, filamentation leads to a significant broadening of the initial pulse spectrum. These properties open the perspective to improve classical LIDAR techniques as well as to laser lightning control.In the laboratory, we have shown that t...

  18. Pulse width tunable subpicosecond pulse generation from an actively modelocked monolithic MQW laser/MQW electroabsorption modulator

    Science.gov (United States)

    Takada, A.; Sato, K.; Saruwatari, M.; Yamamoto, M.

    1994-05-01

    Actively modelocked pulses are generated from a 1.59 micron MQW laser integrated with an MQW electroabsorption modulator driven at the monolithic cavity frequency. The pulse width is controlled from 39 ps to 0.55 ps by changing the inverse bias voltage applied to the electroabsorption modulator and by linear pulse compression using a fiber.

  19. Differential-output B-dot and D-dot monitors for current and voltage measurements on a 20-MA, 3-MV pulsed-power accelerator

    Directory of Open Access Journals (Sweden)

    T. C. Wagoner

    2008-10-01

    Full Text Available We have developed a system of differential-output monitors that diagnose current and voltage in the vacuum section of a 20-MA 3-MV pulsed-power accelerator. The system includes 62 gauges: 3 current and 6 voltage monitors that are fielded on each of the accelerator’s 4 vacuum-insulator stacks, 6 current monitors on each of the accelerator’s 4 outer magnetically insulated transmission lines (MITLs, and 2 current monitors on the accelerator’s inner MITL. The inner-MITL monitors are located 6 cm from the axis of the load. Each of the stack and outer-MITL current monitors comprises two separate B-dot sensors, each of which consists of four 3-mm-diameter wire loops wound in series. The two sensors are separately located within adjacent cavities machined out of a single piece of copper. The high electrical conductivity of copper minimizes penetration of magnetic flux into the cavity walls, which minimizes changes in the sensitivity of the sensors on the 100-ns time scale of the accelerator’s power pulse. A model of flux penetration has been developed and is used to correct (to first order the B-dot signals for the penetration that does occur. The two sensors are designed to produce signals with opposite polarities; hence, each current monitor may be regarded as a single detector with differential outputs. Common-mode-noise rejection is achieved by combining these signals in a 50-Ω balun. The signal cables that connect the B-dot monitors to the balun are chosen to provide reasonable bandwidth and acceptable levels of Compton drive in the bremsstrahlung field of the accelerator. A single 50-Ω cable transmits the output signal of each balun to a double-wall screen room, where the signals are attenuated, digitized (0.5-ns/sample, numerically compensated for cable losses, and numerically integrated. By contrast, each inner-MITL current monitor contains only a single B-dot sensor. These monitors are fielded in opposite-polarity pairs. The two

  20. Differential B-dot and D-dot monitors for current and voltage measurements on a 20-MA 3-MV pulsed-power accelerator.

    Energy Technology Data Exchange (ETDEWEB)

    Shoup, Roy Willlam (ITT Industries, Albuquerque, NM); Gilliland, Terrance Leo (Ktech Corporation, Albuquerque, NM); Lee, James R.; Speas, Christopher Shane; Kim, Alexandre A. (High Current Electronic Institute, Russian Academy of Sciences, Tomsk, Russia); Struve, Kenneth William; York, Mathew William; Leifeste, Gordon T.; Rochau, Gregory Alan; Sharpe, Arthur William; Stygar, William A.; Porter, John Larry Jr.; Wagoner, Tim C. (Ktech Corporation, Albuquerque, NM); Reynolds, Paul Gerard (Team Specialty Products Corporation, Albuquerque, NM); Slopek, Jeffrey Scott (Ktech Corporation, Albuquerque, NM); Moore, William B. S.; Dinwoodie, Thomas Albert (Ktech Corporation, Albuquerque, NM); Woodring, R. M. (Ktech Corporation, Albuquerque, NM); Broyles, Robin Scott (Ktech Corporation, Albuquerque, NM); Mills, Jerry Alan; Melville, J. A. (Prodyn Technologies Incorporated, Albuquerque, NM); Dudley, M. E. (Ktech Corporation, Albuquerque, NM); Androlewicz, K. E. (Ktech Corporation, Albuquerque, NM); Mourning, R. W. (Ktech Corporation, Albuquerque, NM); Moore, J. K. (Ktech Corporation, Albuquerque, NM); Serrano, Jason Dimitri (Ktech Corporation, Albuquerque, NM); Ives, H. C. (EG& G, Albuquerque, NM); Johnson, M. F. (Team Specialty Products Corporation, Albuquerque, NM); Peyton, B. P. (Ktech Corporation, Albuquerque, NM); Leeper, Ramon Joe; Savage, Mark Edward; Donovan, Guy Louis; Spielman, R. B. (Ktech Corporation, Albuquerque, NM); Seamen, Johann F.

    2007-12-01

    We have developed a system of differential-output monitors that diagnose current and voltage in the vacuum section of a 20-MA 3-MV pulsed-power accelerator. The system includes 62 gauges: 3 current and 6 voltage monitors that are fielded on each of the accelerator's 4 vacuum-insulator stacks, 6 current monitors on each of the accelerator's 4 outer magnetically insulated transmission lines (MITLs), and 2 current monitors on the accelerator's inner MITL. The inner-MITL monitors are located 6 cm from the axis of the load. Each of the stack and outer-MITL current monitors comprises two separate B-dot sensors, each of which consists of four 3-mm-diameter wire loops wound in series. The two sensors are separately located within adjacent cavities machined out of a single piece of copper. The high electrical conductivity of copper minimizes penetration of magnetic flux into the cavity walls, which minimizes changes in the sensitivity of the sensors on the 100-ns time scale of the accelerator's power pulse. A model of flux penetration has been developed and is used to correct (to first order) the B-dot signals for the penetration that does occur. The two sensors are designed to produce signals with opposite polarities; hence, each current monitor may be regarded as a single detector with differential outputs. Common-mode-noise rejection is achieved by combining these signals in a 50-{Omega} balun. The signal cables that connect the B-dot monitors to the balun are chosen to provide reasonable bandwidth and acceptable levels of Compton drive in the bremsstrahlung field of the accelerator. A single 50-{omega} cable transmits the output signal of each balun to a double-wall screen room, where the signals are attenuated, digitized (0.5-ns/sample), numerically compensated for cable losses, and numerically integrated. By contrast, each inner-MITL current monitor contains only a single B-dot sensor. These monitors are fielded in opposite-polarity pairs. The two

  1. Effect of heating samples during pulsed electron beam annealing on the open-circuit voltage of silicon solar cells

    Energy Technology Data Exchange (ETDEWEB)

    Laugier, A.; Barbier, D.; Doghmane, M.S.; Chemisky, G. (Institut National des Sciences Appliquees de Lyon, 69 - Villeurbanne (France))

    1983-01-01

    Defects associated with pulsed electron beam annealing of P implanted Si solar cells lead to poor Vsub(oc) (< 500mV). Their nature is discussed on the basic of S.E.M. observations, deep level transient spectroscopy study and degradation of electrical characteristics of Schottky barriers. An improved pulsed electron beam annealing process is determined, characterized by a low mean energy electron beam (10 keV) associated to a starting temperature of 450/sup 0/C and low fluences (<= 1J/cm/sup 2/). Values of Vsub(oc) similar to conventional thermal annealing are obtained.

  2. An ultra short pulse reconstruction software applied to the GEMINI high power laser system

    Science.gov (United States)

    Galletti, Mario; Galimberti, Marco; Hooker, Chris; Chekhlov, Oleg; Tang, Yunxin; Bisesto, Fabrizio Giuseppe; Curcio, Alessandro; Anania, Maria Pia; Giulietti, Danilo

    2016-09-01

    The GRENOUILLE traces of Gemini pulses (15 J, 30 fs, PW, shot per 20 s) were acquired in the Gemini Target Area PetaWatt at the Central Laser Facility (CLF), Rutherford Appleton Laboratory (RAL). A comparison between the characterizations of the laser pulse parameters made using two different types of algorithms: Video Frog and GRenouille/FrOG (GROG), was made. The temporal and spectral parameters came out to be in great agreement for the two kinds of algorithms. In this experimental campaign it has been showed how GROG, the developed algorithm, works as well as VideoFrog algorithm with the PetaWatt pulse class.

  3. Memcapacitive characteristics in reactive-metal (Mo, Al)/HfO{sub X}/n-Si structures through migration of oxygen by applied voltage

    Energy Technology Data Exchange (ETDEWEB)

    Yang, Paul; Noh, Young Jun; Baek, Yoon-Jae; Zheng, Hong; Yoon, Tae-Sik, E-mail: tsyoon@mju.ac.kr [Department of Materials Science and Engineering, Myongji University, Gyeonggi-do 449-728 (Korea, Republic of); Kang, Chi Jung [Department of Physics, Myongji University, Gyeonggi-do 449-728 (Korea, Republic of); Lee, Hyun Ho [Department of Chemical Engineering, Myongji University, Gyeonggi-do 449-728 (Korea, Republic of)

    2016-02-01

    Memcapacitive characteristics were investigated in metal-oxide-semiconductor (MOS) structure of reactive electrode (Mo, Al) and hafnium oxide (HfO{sub X}) on n-type Si substrate. The capacitance-voltage curves exhibited sequentially changing capacitance with memory function as repeating voltage sweeps, featured the memcapacitive behaviors. The saturation capacitance was decreased by repeating +V sweeps, while barely changed by −V sweeps. Also, the capacitance-time curves disclosed the same tendency. However, the MOS structure with inert Pt electrode did not show the capacitance change. The memcapacitive behaviors were induced by the migration of oxygen ions from HfO{sub X} to reactive electrodes by applied voltage, which altered the permittivity of HfO{sub X}.

  4. Control of transmission of right circularly polarized laser light in overdense plasma by applied magnetic field pulses.

    Science.gov (United States)

    Ma, Guangjin; Yu, Wei; Yu, M Y; Luan, Shixia; Wu, Dong

    2016-05-01

    The effect of a transient magnetic field on right-hand circularly polarized (RHCP) laser light propagation in overcritical-density plasma is investigated. When the electron gyrofrequency is larger than the wave frequency, RHCP light can propagate along the external magnetic field in an overcritical density plasma without resonance or cutoff. However, when the magnetic field falls to below the cyclotron resonance point, the propagating laser pulse will be truncated and the local plasma electrons resonantly heated. Particle-in-cell simulation shows that when applied to a thin slab, the process can produce intense two-cycle light pulses as well as long-lasting self-magnetic fields.

  5. Analysis of Current Pulses in HeLa-Cell Permeabilization Due to High Voltage DC Corona Discharge.

    Science.gov (United States)

    Chetty, Nevendra K; Chonco, Louis; Ijumba, Nelson M; Chetty, Leon; Govender, Thavendran; Parboosing, Raveen; Davidson, Innocent E

    2016-09-01

    Corona discharges are commonly utilized for numerous practical applications, including bio-technological ones. The corona induced transfer of normally impermeant molecules into the interior of biological cells has recently been successfully demonstrated. The exact nature of the interaction of the corona discharge with a cell membrane is still unknown, however, previous studies have suggested that it is either the electric fields produced by ions or the chemical interaction of the reactive species that result in the disruption of the cell membrane. This disruption of the cell membrane allows molecules to permeate into the cell. Corona discharge current constitutes a series of pulses, and it is during these pulses that the ions and reactive species are produced. It stands to reason, therefore, that the nature of these corona pulses would have an influence on the level of cell permeabilization and cell destruction. In this investigation, an analysis of the width, rise-time, characteristic frequencies, magnitude, and repetition rate of the nanosecond pulses was carried out in order to establish the relationship between these factors and the levels of cell membrane permeabilization and cell destruction. Results obtained are presented and discussed.

  6. An ultra short pulse reconstruction software applied to the GEMINI high power laser system

    Energy Technology Data Exchange (ETDEWEB)

    Galletti, Mario, E-mail: mario.gall22@gmail.com [INFN – LNF, Via Enrico Fermi 40, 00044 Frascati (Italy); Galimberti, Marco [Central Laser Facility, Rutherford Appleton Laboratory, Didcot (United Kingdom); Hooker, Chris [Central Laser Facility, Rutherford Appleton Laboratory, Didcot (United Kingdom); University of Oxford, Oxford (United Kingdom); Chekhlov, Oleg; Tang, Yunxin [Central Laser Facility, Rutherford Appleton Laboratory, Didcot (United Kingdom); Bisesto, Fabrizio Giuseppe [INFN – LNF, Via Enrico Fermi 40, 00044 Frascati (Italy); Curcio, Alessandro [INFN – LNF, Via Enrico Fermi 40, 00044 Frascati (Italy); Sapienza – University of Rome, P.le Aldo Moro, 2, 00185 Rome (Italy); Anania, Maria Pia [INFN – LNF, Via Enrico Fermi 40, 00044 Frascati (Italy); Giulietti, Danilo [Physics Department of the University and INFN, Pisa (Italy)

    2016-09-01

    The GRENOUILLE traces of Gemini pulses (15 J, 30 fs, PW, shot per 20 s) were acquired in the Gemini Target Area PetaWatt at the Central Laser Facility (CLF), Rutherford Appleton Laboratory (RAL). A comparison between the characterizations of the laser pulse parameters made using two different types of algorithms: Video Frog and GRenouille/FrOG (GROG), was made. The temporal and spectral parameters came out to be in great agreement for the two kinds of algorithms. In this experimental campaign it has been showed how GROG, the developed algorithm, works as well as VideoFrog algorithm with the PetaWatt pulse class. - Highlights: • Integration of the diagnostic tool on high power laser. • Validation of the GROG algorithm in comparison to a well-known commercial available software. • Complete characterization of the GEMINI ultra-short high power laser pulse.

  7. Laser emission of dye-doped liquid crystal evices under applying voltage%电场作用下染料掺杂液晶器件的激光辐射

    Institute of Scientific and Technical Information of China (English)

    岱钦; 乌日娜; 杨健; 徐送宁; 全薇

    2011-01-01

    通过在向列相液晶TEB30A中掺杂激光染料DCM和手性剂CB15制作了平面排列态液晶器件.采用Nd:YAG倍频532 nm波段激光作为泵浦光源,测量分析了平行于液晶器件表面方向的受激辐射光谱.当泵浦光较弱时,观察到了染料DCM较宽的荧光辐射谱;随着泵浦光的逐渐增强,辐射谱带逐渐变窄,辐射峰中心波长约为610 nm,最小半峰全宽(FWHM)为11 nm.观察了在器件玻璃基板上施加交流电场后激光辐射的变化情况,结果显示,当外加电压<9 V时,辐射强度随着电压的增大逐渐减弱;当外加电压>9 V,辐射强度迅速衰减,谱线变宽,显示了较好的电场控制特性.文章认为这种现象主要是由于电场作用下液晶分子取向发生变化所致.%A planar texture device was prepared by doping a laser dye (DCM) and a chiral compound (CB15) into a nematic liquid crystal TEB30A. By using a second harmonic Q-switched Nd: YAG pulsed laser (λ=532 nm) as pumping source, the emission spectrum of the device surface in the horizontal direction was measured and analyzed. It shows that a wide emission spectrum can be observed when the pump light is weak. With the increase of pump light, the stimulated emission spectrum is narrowed,and its center wavelength with a least Full Width of Half Maximum (FWHM)about 11 nm is at 610 nm. Moreover,by applying a AC voltage along the perpendicular direction to the surface of the device,the laser emission was also observed. When the applying voltage is less than 9 V,the lasing intensity is weakened with the increase of the voltage. When the applying voltage is greater than 9 V,the emission intensity is decreased sharply. These results can be attributed to the liquid crystal alignment changed on the applying electric field.

  8. REGIMES ANALYSIS OF THE VOLTAGE PULSE REGULATORS ON THE BASIC OF THE INVARIANCE PROPERTY OF THE CONTROL CHARACTERISTICS

    Directory of Open Access Journals (Sweden)

    Penin A.A.

    2009-04-01

    Full Text Available Regime characteristic values are determined relative to character values of regulation curve of switching regulator. Regime changing and the correspondence between various regime parameters are examined as a geometric (projective transformation. This makes possible to validate the regime definition, to restrict the range of their variation on the rising area of the control characteristic, to realize the linearization of this characteristic, to compare different pulse regulators.

  9. 晶体管驱动的阶跃二极管大幅度窄脉冲源%Narrow Pulse Source of High-voltag Based on Step Recovery Diode Driven by Transistor

    Institute of Scientific and Technical Information of China (English)

    杨金钢; 谢嘉; 李红英; 和先孟; 周祖国

    2012-01-01

    Current ways of generating narrow pulse is difficult to generate a high-voltage narrow-pulse or a narrow-pulse of voltage higher than working voltage. This paper presented a method to generate a high-voltage narrow-pulse by using a step recovery diode at low voltage which was driven by bipolar transistor. The basic principle of this method was to realize the generation of a high-voltage narrow-pulse by using step characteristic of step recovery diode, and the excitation source form was redesigned based on bipolar driving. Simulation results showed that the circuit's output pulse voltage was not lower than working voltage and had advantages of simple circuit,adjustable pulse width,prone to be integrated,etc. This method was suitable to generate narrow-pulse for ultra-wideband communication system and played an important role in increasing the detecting distance of ultra-wideband fuze.%目前纳秒级窄脉冲源的实现方法有很多,但很难用低电源产生大幅度窄脉冲,或是实现输出脉冲幅度大于其工作电压.提出了一种采用阶跃恢复二极管在双极型晶体管驱动下实现工作于低电压的大幅度纳秒级窄脉冲源的方法.该方法利用阶跃管的阶跃特性,同时利用晶体管的驱动,对阶跃管的激励源形式进行改进设计,实现大幅度窄脉冲.仿真和测试结果表明:该电路具有输出脉冲幅度不小于工作电压的特点,并具有电路简单、脉宽可调、易于集成等优点,适用于超宽带通信系统中窄脉冲信号的产生.

  10. An ultrashort-pulse reconstruction software: GROG, applied to the FLAME laser system

    Science.gov (United States)

    Galletti, Mario

    2016-03-01

    The GRENOUILLE traces of FLAME Probe line pulses (60mJ, 10mJ after compression, 70fs, 1cm FWHM, 10Hz) were acquired in the FLAME Front End Area (FFEA) at the Laboratori Nazionali di Frascati (LNF), Instituto Nazionale di Fisica Nucleare (INFN). The complete characterization of the laser pulse parameters was made using a new algorithm: GRenouille/FrOG (GROG). A characterization with a commercial algorithm, QUICKFrog, was also made. The temporal and spectral parameters came out to be in great agreement for the two kinds of algorithms. In this experimental campaign the Probe line of FLAME has been completely characterized and it has been showed how GROG, the developed algorithm, works as well as QuickFrog algorithm with this type of pulse class.

  11. Effects of adsorbed proteins, an antifouling agent and long-duration DC voltage pulses on the impedance of silicon-based neural microelectrodes.

    Science.gov (United States)

    Sommakia, Salah; Rickus, Jenna L; Otto, Kevin J

    2009-01-01

    The successful use of implantable neural microelectrodes as neuroprosthetic devices depends on the mitigation of the reactive tissue response of the brain. One of the factors affecting the ultimate severity of the reactive tissue response and the in vivo electrical properties of the microelectrodes is the initial adsorption of proteins onto the surface of the implanted microelectrodes. In this study we quantify the increase in microelectrode impedance magnitude at physiological frequencies following electrode immersion in a 10% bovine serum albumin (BSA) solution. We also demonstrate the efficacy of a common antifouling molecule, poly(ethylene glycol) (PEG), in preventing a significant increase in microelectrode impedance. In addition, we show the feasibility of using long-duration DC voltage pulses to remove adsorbed proteins from the microelectrode surface.

  12. A strategy for sampling on a sphere applied to 3D selective RF pulse design.

    Science.gov (United States)

    Wong, S T; Roos, M S

    1994-12-01

    Conventional constant angular velocity sampling of the surface of a sphere results in a higher sampling density near the two poles relative to the equatorial region. More samples, and hence longer sampling time, are required to achieve a given sampling density in the equatorial region when compared with uniform sampling. This paper presents a simple expression for a continuous sample path through a nearly uniform distribution of points on the surface of a sphere. Sampling of concentric spherical shells in k-space with the new strategy is used to design 3D selective inversion and spin-echo pulses. These new 3D selective pulses have been implemented and verified experimentally.

  13. High- voltage Pulsed Electric Field Sterilization Equipment and Flow Control%高压脉冲电场灭菌设备及其流量控制

    Institute of Scientific and Technical Information of China (English)

    林荣华; 李伟光

    2012-01-01

    In order to optimize the sterilization effect of high-voltage pulsed electric field sterilization equipment, this paper analyzes its function according the tactors of the enfluence on the system, designs the overall structure and PLC-based flow control system by the way of frequency control of motor speed, describes the structure and principle of high-voltage pulse generator and the theory and realization of the flow control based on frequency control as well as the realization of communication between inverters and PLC with RS-485. The result shows that the equipment is able to control and adjust key process parameters well, comtro the flow by a simple and reliable way, and achieve high effective and fast sterilization.%为优化高压脉冲电场灭菌设备的灭菌效果,根据其影响因素进行了系统功能需求分析,设计了设备的总体架构,采用变频调速的方法,设计了基于PLC的流量控制系统.简述了高压脉冲发生器的结构及原理,重点介绍了基于变频调速的流量控制原理与实现,变频器与PLC的RS - 485通信的实现.实验表明,设备实现了关键工艺参数可调可控,运行效果良好,简单可靠地实现了流量的控制,实现了快速高效灭菌.

  14. Can the use of pulsed direct current induce oscillation in the applied pressure during spark plasma sintering?

    Directory of Open Access Journals (Sweden)

    David Salamon, Mirva Eriksson, Mats Nygren and Zhijian Shen

    2012-01-01

    Full Text Available The spark plasma sintering (SPS process is known for its rapid densification of metals and ceramics. The mechanism behind this rapid densification has been discussed during the last few decades and is yet uncertain. During our SPS experiments we noticed oscillations in the applied pressure, related to a change in electric current. In this study, we investigated the effect of pulsed electrical current on the applied mechanical pressure and related changes in temperature. We eliminated the effect of sample shrinkage in the SPS setup and used a transparent quartz die allowing direct observation of the sample. We found that the use of pulsed direct electric current in our apparatus induces pressure oscillations with the amplitude depending on the current density. While sintering Ti samples we observed temperature oscillations resulting from pressure oscillations, which we attribute to magnetic forces generated within the SPS apparatus. The described current–pressure–temperature relations might increase understanding of the SPS process.

  15. Determination voltage applied to an X-ray tube using the spectrum; Determinacao da tensao aplicada em um tubo de raios-X usando o espectro

    Energy Technology Data Exchange (ETDEWEB)

    Albuquerque, M.A.G.; David, M.G.; Almeida, Carlos Eduardo de; Magalhaes, Luis Alexandre Goncalves, E-mail: malbuqueque@hotmail.com [Universidade do Estado do Rio de Janeiro (UERJ), Rio de Janeiro, RJ (Brazil). Lab. de Ciencias Radiologicas; Peixoto, Guilherme [Instituto de Radioprotecao e Dosimetria (IRD/CNEN-RJ), Rio de Janeiro, RJ (Brazil)

    2015-07-01

    This work shows the methodology used to determine the voltage applied in an X-ray tube using their spectra. The measurements were made using a detector Cadmium telluride . Before the measurements are carried out detector was calibrated with a source of {sup 241}Am. After obtaining the spectra , the mean energies were calculated , the electron accelerating potential (k Vp ) of each spectrum is constructed a calibration straight for the kVp this tube. (author)

  16. Demonstration of InAlN/AlGaN high electron mobility transistors with an enhanced breakdown voltage by pulsed metal organic chemical vapor deposition

    Energy Technology Data Exchange (ETDEWEB)

    Xue, JunShuai, E-mail: junshuaixue@hotmail.com; Zhang, JinCheng; Hao, Yue [Key Laboratory of Wide Band Gap Semiconductor Materials and Devices, School of Microelectronics, Xidian University, Xi' an 710071 (China)

    2016-01-04

    In this work, InAlN/AlGaN heterostructures employing wider bandgap AlGaN instead of conventional GaN channel were grown on sapphire substrate by pulsed metal organic chemical vapor deposition, where the nominal Al composition in InAlN barrier and AlGaN channel were chosen to be 83% and 5%, respectively, to achieve close lattice-matched condition. An electron mobility of 511 cm{sup 2}/V s along with a sheet carrier density of 1.88 × 10{sup 13 }cm{sup −2} were revealed in the prepared heterostructures, both of which were lower compared with lattice-matched InAlN/GaN due to increased intrinsic alloy disorder scattering resulting from AlGaN channel and compressively piezoelectric polarization in barrier, respectively. While the high electron mobility transistor (HEMT) processed on these structures not only exhibited a sufficiently high drain output current density of 854 mA/mm but also demonstrated a significantly enhanced breakdown voltage of 87 V, which is twice higher than that of reported InAlN/GaN HEMT with the same device dimension, potential characteristics for high-voltage operation of GaN-based electronic devices.

  17. Demonstration of InAlN/AlGaN high electron mobility transistors with an enhanced breakdown voltage by pulsed metal organic chemical vapor deposition

    Science.gov (United States)

    Xue, JunShuai; Zhang, JinCheng; Hao, Yue

    2016-01-01

    In this work, InAlN/AlGaN heterostructures employing wider bandgap AlGaN instead of conventional GaN channel were grown on sapphire substrate by pulsed metal organic chemical vapor deposition, where the nominal Al composition in InAlN barrier and AlGaN channel were chosen to be 83% and 5%, respectively, to achieve close lattice-matched condition. An electron mobility of 511 cm2/V s along with a sheet carrier density of 1.88 × 1013 cm-2 were revealed in the prepared heterostructures, both of which were lower compared with lattice-matched InAlN/GaN due to increased intrinsic alloy disorder scattering resulting from AlGaN channel and compressively piezoelectric polarization in barrier, respectively. While the high electron mobility transistor (HEMT) processed on these structures not only exhibited a sufficiently high drain output current density of 854 mA/mm but also demonstrated a significantly enhanced breakdown voltage of 87 V, which is twice higher than that of reported InAlN/GaN HEMT with the same device dimension, potential characteristics for high-voltage operation of GaN-based electronic devices.

  18. Influence of pulse polarity on electron emission property of antiferroelectric ceramic

    Institute of Scientific and Technical Information of China (English)

    SHENG ZhaoXuan; FENG YuJun; OUI Jie; HUANG Xuan; XU Zhuo; SUN XinLi

    2008-01-01

    The electron emission property of a novel antiferroelectric cathode material lanthanum-doped lead zirconate stannate titanate (PLZST) on the application of positive or negative triggering voltage pulses has been investigated. All experiments were performed in a vacuum of 10-5 Torr and at room tempera-ture. It was discovered that there were two electron emission pulses when low positive triggering voltage was applied to the rear electrode, and three electron emission pulses when high positive trig-gering voltage was applied. However there were always two electron emission pulses when negative triggering pulses were applied. This phenomenon is proposed to be a result of both field electron emission at triple junctions and electron emission caused by polarization reversal. The experimental observations indicate that domain movement in the vicinity close to the triple junction under applica-tion of the triggering voltage pulse may be a primary origin of electron emission from PLZST.

  19. Comparative study of pulsed laser cleaning applied to weathered marble surfaces

    Science.gov (United States)

    Ortiz, P.; Antúnez, V.; Ortiz, R.; Martín, J. M.; Gómez, M. A.; Hortal, A. R.; Martínez-Haya, B.

    2013-10-01

    The removal of unwanted matter from surface stones is a demanding task in the conservation of cultural heritage. This paper investigates the effectiveness of near-infrared (IR) and ultraviolet (UV) laser pulses for the cleaning of surface deposits, iron oxide stains and different types of graffiti (black, red and green sprays and markers, and black cutting-edge ink) on dolomitic white marble. The performance of the laser techniques is compared to common cleaning methods on the same samples, namely pressurized water and chemical treatments. The degree of cleaning achieved with each technique is assessed by means of colorimetric measurements and X-ray microfluorescence. Eventual morphological changes induced on the marble substrate are monitored with optical and electronic microscopy. It is found that UV pulsed laser ablation at 266 nm manages to clean all the stains except the cutting-edge ink, although some degree of surface erosion is produced. The IR laser pulses at 1064 nm can remove surface deposits and black spray acceptably, but a yellowing is observed on the stone surface after treatment. An economic evaluation shows that pulsed laser cleaning techniques are advantageous for the rapid cleaning of small or inaccessible surface areas, although their extensive application becomes expensive due to the long operating times required.

  20. Thermal processing of thin films using ultra-short laser pulses: applied to photovoltaic materials

    NARCIS (Netherlands)

    Scorticati, D.

    2015-01-01

    In this thesis a novel approach to raise the thermal selectivity of superficial heat treatments, exploiting ultra-short laser pulses, is proposed and studied. That is, the effective applicability of ultrafast lasers for selective heat treatments is proven by increasing the performance of different

  1. Comparative study of pulsed laser cleaning applied to weathered marble surfaces

    Energy Technology Data Exchange (ETDEWEB)

    Ortiz, P., E-mail: mportcal@upo.es [Department of Physical, Chemical and Natural Systems, Universidad Pablo de Olavide, 41013 Seville (Spain); Antúnez, V.; Ortiz, R.; Martín, J.M. [Department of Physical, Chemical and Natural Systems, Universidad Pablo de Olavide, 41013 Seville (Spain); Gómez, M.A. [Instituto Andaluz de Patrimonio Histórico, Camino de los Descubrimientos s/n, 41092 Seville (Spain); Hortal, A.R.; Martínez-Haya, B. [Department of Physical, Chemical and Natural Systems, Universidad Pablo de Olavide, 41013 Seville (Spain)

    2013-10-15

    The removal of unwanted matter from surface stones is a demanding task in the conservation of cultural heritage. This paper investigates the effectiveness of near-infrared (IR) and ultraviolet (UV) laser pulses for the cleaning of surface deposits, iron oxide stains and different types of graffiti (black, red and green sprays and markers, and black cutting-edge ink) on dolomitic white marble. The performance of the laser techniques is compared to common cleaning methods on the same samples, namely pressurized water and chemical treatments. The degree of cleaning achieved with each technique is assessed by means of colorimetric measurements and X-ray microfluorescence. Eventual morphological changes induced on the marble substrate are monitored with optical and electronic microscopy. It is found that UV pulsed laser ablation at 266 nm manages to clean all the stains except the cutting-edge ink, although some degree of surface erosion is produced. The IR laser pulses at 1064 nm can remove surface deposits and black spray acceptably, but a yellowing is observed on the stone surface after treatment. An economic evaluation shows that pulsed laser cleaning techniques are advantageous for the rapid cleaning of small or inaccessible surface areas, although their extensive application becomes expensive due to the long operating times required.

  2. 负偏压法测试大电压LED器件热阻%Measuring thermal resistance for high voltage LED device and module by applying negative bias voltage

    Institute of Scientific and Technical Information of China (English)

    陈国龙; 雷瑞瑞; 陈焕庭; 陈莹亮; 吕毅军; 高玉琳; 朱丽虹; 陈忠

    2012-01-01

    热阻是衡量LED器件散热性能的重要热学参数.采用外接负偏压恒压源方法,分别使用T3Ster/Teraled热光参数测试仪和NC2991热阻仪对正向电压超过仪器量程的同一型号功率型LED的热阻进行测试,并对两种测试结果的误差进行比较分析讨论.该方法拓展了热阻仪测量范围,使正向电压大于5V的LED器件/模块的热阻测试成为可能.%Thermal resistance is a key parameter on rating the heat dissipating capability of LEDs, so its measurement becomes particularly essential. A thermal resistance measurement method for high voltage LED device and module is provided here, which can measure LED sample with forward voltage larger than 5V by applying negative bias voltage to the T3Ster/Teraled and the NC2991 thermal resistance testers respectively. The results are further compared and discussed and prove to effectively expand the testing range of thermal resistance tester.

  3. Vacuum breakdown limit and quantum efficiency obtained for various technical metals using dc and pulsed voltage sources

    CERN Document Server

    Le Pimpec, F; Paraliev, M; Ganter, R; Hauri, C; Ivkovic, S; 10.1116/1.3478300

    2010-01-01

    For the SwissFEL project, an advanced high gradient low emittance gun is under development. Reliable operation with an electric field, preferably above 125 MV/m at a 4 mm gap, in the presence of an UV laser beam, has to be achieved in a diode configuration in order to minimize the emittance dilution due to space charge effects. In the first phase, a DC breakdown test stand was used to test different metals with different preparation methods at voltages up to 100 kV. In addition high gradient stability tests were also carried out over several days in order to prove reliable spark-free operation with a minimum dark current. In the second phase, electrodes with selected materials were installed in the 250 ns FWHM, 500 kV electron gun and tested for high gradient breakdown and for quantum efficiency using an ultra-violet laser.

  4. 150kV全固态高压脉冲发生器设计%Design of 150 kV all-solid-state high voltage pulsed power generator

    Institute of Scientific and Technical Information of China (English)

    雷宇; 邱剑; 刘克富

    2012-01-01

    The paper presents a design of all-solid-state pulsed power generator based on Marx generator with MOSFET semiconductor switch devices. Charging resistance is replaced by fast recovery diode in the circuit, which reduces power loss in charging process. Drive circuit is integrated in and gets power supply from main circuit. Optical fiber is used to deliver the drive signal so as to protect it from the interference of discharging. A clockwise/counter-clockwise ring-shaped compact configuration is applied, which reduces the loop inductance, and makes the generator modularized and compact. The proposed generator is com-posed of 180 Marx unites in series, each of which is charged at a low voltage of 900 V, and generates a fast output pulse of voltage 150 kV, rise time less than 500 ns and duration adjustable between 1 and 5 Ωs. Some experimental results of the pulsed power generator are listed, with a load of 50 kΩ resistance and 5 pF capacitance in parallel. Through comparison and analysis, some factors affecting the rise time of output pulses are summarized, including loop inductance, drive voltage of MOSFET and distributed capacitance of main circuit. Approaches for pulse rise time improvement are also discussed.%设计了一种基于全固态MOSFET半导体开关器件的Marx脉冲发生器.充电回路用快恢复二极管代替充电电阻,减小了充电部分功率损耗;将主电路和驱动电路集成在一起,采用自取电模式给驱动电路供电;由光纤传输驱动信号,抑制了放电回路对触发信号的干扰;采用顺/逆时针方向环形分布的紧凑型拓扑结构,不仅减小了回路电感,而且实现了脉冲发生器的小型化与模块化.所设计的Marx发生器充电部分仅需提供900 V低压,用180级单元串联,获得最高幅值为150 kV、脉宽1~5 μs可调的高压快脉冲,前沿控制在500ns以内.利用该脉冲发生器在50 kΩ电阻和5 pF电容并联的等效负载上进行了一系列实验;比

  5. Efficiency enhancement of TiO2 (active material) solar cell by inserting copper particles grown with pulse voltage electroplating method

    Science.gov (United States)

    Rokhmat, Mamat; Sutisna; Wibowo, Edy; Khairurrijal; Abdullah, Mikrajuddin

    2017-01-01

    Here, we report the manufacture of a solar cell using TiO2 nanoparticles as photon absorbers and copper bridges inserted between the TiO2 particles. The copper bridges were synthesized by the pulse voltage electroplating method, and the effect of the pulse duty cycle was explored. The amount of copper deposited between TiO2 particles can be controlled by varying the duty cycles and the deposition time. We found that the cell fabricated by the deposition of copper at duty cycles of 60% and a deposition time of 30 s exhibited the highest efficiency (2.21%). Efficiency was improved to 3.5% following the post-treatment of the cell with NaOH. We also proposed a simple mathematical model to explain the dependence of the efficiency on the amount of copper. Efficiencies of more than 3% for solar cells made by a simple method and using inexpensive materials make these solar cells promising competition for the current commercial solar cells.

  6. Tuning and Cold Test of a Four-Vane RFQ with Ramped Inter-Vane Voltage for the Compact Pulsed Hadron Source

    Science.gov (United States)

    Xing, Qing-Zi; Du, Lei; Zheng, Shu-Xin; Guan, Xia-Ling; Li, Jian; Cai, Jin-Chi; Gong, Cun-Kui; Wang, Xue-Wu; Tang, Chuan-Xiang; James, Billen; James, Stovall; Lloyd, Young

    2013-05-01

    A four-vane radio-frequency quadrupole (RFQ) accelerator is under construction for the Compact Pulsed Hadron Source (CPHS) project at Tsinghua University. The 3 m-long RFQ will accelerate a 50keV proton beam from the ECR source to 3MeV, and deliver it to the downstream drift tube linac (DTL) with a peak current of 50mA, pulse length of 0.5 ms and beam duty factor of 2.5%. The inter-vane voltage is designed to increase with the longitudinal position to produce a short RFQ. Coupling plates are therefore not necessary. The cavity cross section and vane-tip geometry are tailored as a function of the longitudinal position, while limiting the peak surface electric field to 1.8 Kilpatrick. The RFQ is designed, manufactured, and installed at Tsinghua University. We also present the tuning and cold test results of the RFQ accelerator. After final tuning, the relative error of the quadrupole field is within 2%, and the admixture of the two dipole modes are less than 2% of the quadrupole mode.

  7. Probability of cavitation for single ultrasound pulses applied to tissues and tissue-mimicking materials.

    Science.gov (United States)

    Maxwell, Adam D; Cain, Charles A; Hall, Timothy L; Fowlkes, J Brian; Xu, Zhen

    2013-03-01

    In this study, the negative pressure values at which inertial cavitation consistently occurs in response to a single, two-cycle, focused ultrasound pulse were measured in several media relevant to cavitation-based ultrasound therapy. The pulse was focused into a chamber containing one of the media, which included liquids, tissue-mimicking materials, and ex vivo canine tissue. Focal waveforms were measured by two separate techniques using a fiber-optic hydrophone. Inertial cavitation was identified by high-speed photography in optically transparent media and an acoustic passive cavitation detector. The probability of cavitation (P(cav)) for a single pulse as a function of peak negative pressure (p(-)) followed a sigmoid curve, with the probability approaching one when the pressure amplitude was sufficient. The statistical threshold (defined as P(cav) = 0.5) was between p(-) = 26 and 30 MPa in all samples with high water content but varied between p(-) = 13.7 and >36 MPa in other media. A model for radial cavitation bubble dynamics was employed to evaluate the behavior of cavitation nuclei at these pressure levels. A single bubble nucleus with an inertial cavitation threshold of p(-) = 28.2 megapascals was estimated to have a 2.5 nm radius in distilled water. These data may be valuable for cavitation-based ultrasound therapy to predict the likelihood of cavitation at various pressure levels and dimensions of cavitation-induced lesions in tissue.

  8. Active power control with undead-band voltage & frequency droop applied to a meshed DC grid test system

    DEFF Research Database (Denmark)

    Vrana, Til Kristian; Zeni, Lorenzo; Fosso, Olav Bjarte

    2012-01-01

    A new method for controlling active power in HVDC grids has been tested on the meshed CIGRE B4 DC grid test system. The control strategy is based on the recently proposed undead-band droop control, which combines DC voltage and AC frequency droop. It provides sufficient roomm for optimisation...... for both normal and disturbed operation. Its main features are flexibility, reliability due to distributed control, easy expandability of the system and minimisation of communication needs. The control technique has been tested and its effectiveness has been verified to demonstrate its suitability...

  9. Breakdown voltage of metal-oxide resistors in liquid argon

    Energy Technology Data Exchange (ETDEWEB)

    Bagby, L. F. [Fermilab; Gollapinni, S. [Kansas State U.; James, C. C. [Fermilab; Jones, B. J.P. [MIT; Jostlein, H. [Fermilab; Lockwitz, S. [Fermilab; Naples, D. [Pittsburgh U.; Raaf, J. L. [Fermilab; Rameika, R. [Fermilab; Schukraft, A. [Fermilab; Strauss, T. [Bern U., LHEP; Weber, M. S. [Bern U., LHEP; Wolbers, S. A. [Fermilab

    2014-11-07

    We characterized a sample of metal-oxide resistors and measured their breakdown voltage in liquid argon by applying high voltage (HV) pulses over a 3 second period. This test mimics the situation in a HV-divider chain when a breakdown occurs and the voltage across resistors rapidly rise from the static value to much higher values. All resistors had higher breakdown voltages in liquid argon than their vendor ratings in air at room temperature. Failure modes range from full destruction to coating damage. In cases where breakdown was not catastrophic, subsequent breakdown voltages were lower in subsequent measuring runs. One resistor type withstands 131 kV pulses, the limit of the test setup.

  10. Voltage-Induced Effect on Resistance of C:N/Si Heterojunctions

    Institute of Scientific and Technical Information of China (English)

    GAO Xi-Li; ZHANG Xiao-Zhong; WAN Cai-Hua; WANG Ji-Min

    2012-01-01

    Nitrogen doped a-C/Silicon (a-C:N/Si) heterojunctions have been fabricated by using the pulsed laser deposition (PLD) technique and their current-voltage characteristics at various temperatures are investigated.For reverse applied voltages,a-C:N/Si heterojunctions exhibit metal-insulator transition characteristics and the transition temperature can be controlled by the applied voltages.After the excitation of repeated high reverse applied voltages,the current-voltage curves show obvious hysteresis behaviors at low temperatures.These hysteresis behaviors are reproducible and the ratio of the high/low resistance can be greater than 104.%Nitrogen doped a-C/Silicon (a-C:N/Si) heterojunctions have been fabricated by using the pulsed laser deposition (PLD) technique and their current-voltage characteristics at various temperatures are investigated. For reverse applied voltages, a-C.N/Si heterojunctions exhibit metal-insulator transition characteristics and the transition temperature can be controlled by the applied voltages. After the excitation of repeated high reverse applied voltages, the current-voltage curves show obvious hysteresis behaviors at low temperatures. These hysteresis behaviors are reproducible and the ratio of the high/low resistance can be greater than 104.

  11. Applying Hanford Tank Mixing Data to Define Pulse Jet Mixer Operation

    Energy Technology Data Exchange (ETDEWEB)

    Wells, Beric E.; Bamberger, Judith A.; Recknagle, Kurtis P.; Enderlin, Carl W.; Minette, Michael J.; Holton, Langdon K.

    2015-12-07

    Pulse jet mixed (PJM) process vessels are being developed for storing, blending, and chemical processing of nuclear waste slurries at the Waste Treatment and Immobilization Plant (WTP) to be built at Hanford, Washington. These waste slurries exhibit variable process feed characteristics including Newtonian to non-Newtonian rheologies over a range of solids loadings. Waste feed to the WTP from the Hanford Tank Farms will be accomplished via the Waste Feed Delivery (WFD) system which includes million-gallon underground storage double-shell tanks (DSTs) with dual-opposed jet mixer pumps. Experience using WFD type jet mixer pumps to mobilize actual Hanford waste in DSTs may be used to establish design threshold criteria of interest to pulse jet mixed process vessel operation. This paper describes a method to evaluate the pulse jet mixed vessel capability to process waste based on information obtained during mobilizing and suspending waste by the WFD system jet mixer pumps in a DST. Calculations of jet velocity and wall shear stress in a specific pulse jet mixed process vessel were performed using a commercial computational fluid dynamics (CFD) code. The CFD-modelled process vessel consists of a 4.9-m- (16-ft-) diameter tank with a 2:1 semi-elliptical head, a single, 10-cm (4-in.) downward facing 60-degree conical nozzle, and a 0.61-m (24-in.) inside diameter PJM. The PJM is located at 70% of the vessel radius with the nozzle stand-off-distance 14 cm (6 in.) above the vessel head. The CFD modeled fluid velocity and wall shear stress can be used to estimate vessel waste-processing performance by comparison to available actual WFD system process data. Test data from the operation of jet mixer pumps in the 23-m (75-ft) diameter DSTs have demonstrated mobilization, solid particles in a sediment matrix were moved from their initial location, and suspension, mobilized solid particles were moved to a higher elevation in the vessel than their initial location, of waste solids

  12. Time-resolved pulsed stimulated infrared thermography applied to carbon-epoxy non destructive evaluation

    Science.gov (United States)

    Krapez, J.-C.; Boscher, D.; Delpech, Ph.; Deom, A.; Gardette, G.; Balageas, D.

    Since several years, time-resolved pulsed stimulated infrared thermography (SIRT) has been developed at ONERA with the aim of combining fast screening and quantitative characterization. The analysis of pixel by pixel thermograms leads to depth-location and thermal resistance images of delaminations. In this paper we present recent enhancements of the portable SIRT system and refinement of the data reduction procedure which demonstrate the possibility of detecting and evaluating delaminations in C-epoxy at depths higher than 3 mm. A 2-D inversion procedure is proposed to better characterize defects of reduced lateral extend as compared to the former 1-D method.

  13. Cu2O/Ag co-deposited TiO2 nanotube array film prepared by pulse-reversing voltage and photocatalytic properties

    Science.gov (United States)

    Ding, Qi; Chen, Suiyuan; Shang, Fanmin; Liang, Jing; Liu, Changsheng

    2016-12-01

    In this experiment, Cu2O/Ag co-deposition TiO2 nanotube array (Cu2O-Ag-TNT) film was prepared on pure Ti substrate with the method of combining anodic oxidation and electrodeposition by pulse-reversing voltage power supply in the electrolyte of NH4F, ethylene glycol, CuNO3 · 3H2O and AgNO3. The morphology, phase, chemical composition, photocatalytic property and mechanism of the nanotube array film were studied by means of scanning electron microscopy, energy dispersive x-ray spectroscopy, x-ray diffraction, x-ray photoelectron spectroscopy, transmission electron microscopy, UV-vis diffuse reflectance spectra, photoluminescence and photocatalytic degradation under visible light. The results showed that the depositional Cu2O and Ag existed in two forms, being the small-particle dispersion and large-particle sedimentary phase in the nanotube arrays: Cu2O-Ag-TNTs for different doping amounts of Ag could be prepared by adjusting the concentration of AgNO3 and the reverse voltages; with changing of the doping amount of Ag, the band gap and photo-generated electron-hole pair recombination rate also changed, and under the conditions of annealing and the optimized process parameter, the band gap of the nanotube arrays narrowed 0.49 eV and the rate of electron and pair recombination decreased noticeably; the nanotube array film for the concentration of 0.5 cm2 ml-1 degraded the methylene blue of 8 mg L-1, and the degradation rate reached above 98%. The co-deposition Cu2O-Ag-TNT film prepared by the one-step method performed well in the field of photocatalysis under visible light.

  14. Pulsed eddy current and ultrasonic data fusion applied to stress measurement

    Science.gov (United States)

    Habibalahi, A.; Safizadeh, M. S.

    2014-05-01

    Stress measurement and its variation are key problems in the operating performance of materials. Stress can affect the material properties and the life of components. There are several destructive and nondestructive techniques that are used to measure stress. However, no single nondestructive testing (NDT) technique or method is satisfactory to fully assess stress. This paper presents an NDT data fusion method to improve stress measurement. An aluminum alloy 2024 specimen subjected to stress simulation is nondestructively inspected using pulsed eddy current and ultrasonic techniques. Following these nondestructive examinations, the information gathered from these two NDT methods has been fused using a suitable fuzzy combination operator. The results obtained with these processes are presented in this paper and their efficiency is discussed. It is shown that the fusion of NDT data with a suitable fuzzy operator can be adequate to improve the reliability of stress measurements.

  15. Neurostimulation using subnanosecond electric pulses

    Science.gov (United States)

    Xiao, Shu; Pakhomov, Andrei; Guo, Fei; Polisetty, Swetha; Schoenbach, Karl H.

    2013-02-01

    We have for the first time recorded action potentials in rat hippocampus neurons when they were stimulated by subnanosecond electric pulses. The preliminary results show that applying a series of pulses allowed the accumulation of depolarization before activating the voltage gated channels. The depolarization only occurred when the electric pulses were applied. It is unclear whether the depolarization is caused by the charge accumulation across the membrane or the cation influx due to the membrane permeabilization. We have also conducted an electromagnetic simulation of delivering subnanosecond pulses to tissues using an impulse radiating antenna. The results show that the pulses can be confined in the deep region in the brain but the amplitude is reduced significantly due to the attenuation of the tissues. A partially lossy dielectric lens may be used to reverse the decreasing trend of the electric field.

  16. 高压脉冲电场对微生物的灭活作用研究进展%Research Progress in the Effect of High-voltage Pulsed Electric Field on Microorganism Inactivation

    Institute of Scientific and Technical Information of China (English)

    陈新梅; 薛文静; 赵元

    2016-01-01

    Objective:To review the inactivation effect of high-voltage pulsed electric field on microorganism to provid theoretical basis for the further research and sterilization application of high-voltage pulsed electric field. Methods:The combination of high-volt-age pulse electric field, microbiology and pulse electric field as the keywords, the research results of high-voltage pulsed electric field on microbial inactivation in PubMed, CNKI, VIP Chinese journal full text database and Wanfang database during 2010 and 2015 were retrieved, summarized and reviewed. Results:As a non-thermal sterilization technology, high-voltage pulsed electric field not only had the characteristics of short sterilization time, narrow increasing extent of temperature and low energy consumption, but also could keep the original flavor of food. Conclusion:With the development of related technology, high-voltage pulsed electric field is expected to re-alize industrialization.%目的::综述高压脉冲电场对微生物的灭活作用,为进一步研究和应用高压脉冲电场灭菌提供理论基础。方法:以“高压脉冲电场”、“微生物”、“Pulse Electric Field”等组合为关键词,检索2010~2015年PubMed、中国知网、维普中文期刊全文数据库、万方数据库中有关高压脉冲电场对微生物的灭活作用的研究成果,进行总结和综述。结果:高压脉冲电场作为一种非热灭菌技术,不仅具有灭菌时间短、升温幅度小、耗能少的特点,还能保持食品原有风味不变。结论:随着相关技术的发展,高压脉冲电场有望实现产业化。

  17. Development of High - voltage Pulse - transmission Electric Cable for Plasma Drill%等离子体钻机高压脉冲传输电缆的研制

    Institute of Scientific and Technical Information of China (English)

    季念迎; 裴彦良; 闫克平; 刘晨光; 章志成

    2012-01-01

    设计了等离子钻机高压脉冲传输电缆的结构,讨论了高压绝缘层的设计及材料选择.在此基础上,开展了高压脉冲传输电缆的绝缘阻抗和波阻抗测试实验.实验测试结果表明,所研制的传输电缆具有较高的绝缘性能和较小的波阻抗,可基本满足等离子体钻机的需要.%The structure of the high - voltage pulse - transmission electric cable was designed. The design of high - voltage insulation layer and the insulation material were discussed. Based on what mentioned above, the insulating resistance and the wave resistance tests of the high - voltage pulse - transmission electric cable were carried out. The test results show that the high - voltage pulse - transmission electric cable has good insulating property and little wave resistance, which meets the challenges of the plasma drill.

  18. 高压脉冲电场灭菌方法研究概况%Research on the High-voltage Pulsed Electric Field Sterilization Method

    Institute of Scientific and Technical Information of China (English)

    陈新梅; 李莹; 陈新华

    2014-01-01

    The high-voltage pulsed electric field (PEF) sterilization has significant advantages such as a short process-ing time,low energy consumption,small temperature rise,high sterilization rate and not affecting the effective components of drugs,and so on. Based on the review of the mechanism of PEF sterilization,sterilization devices and the possible influ-encing factors,and the comparison of other sterilization methods,the evaluation of the PEF sterilization method was made and the existing problems and commercial prospects in the fields of food and pharmaceuticals were discussed.%高压脉冲电场灭菌具有处理时间短、耗能低、升温小、灭菌率高、不影响药物的有效成分等显著优点,本文通过对高压脉冲电场灭菌作用机理、灭菌装置、可能的影响因素总结及与其他灭菌方式的比较,对高压脉冲电场灭菌方式进行评价,并探讨其现存问题及在食品、药品领域的应用前景。

  19. A new technique to study transient conductivity under pulsed monochromatic light in Cr-doped GaAs using acoustoelectric voltage measurement

    Science.gov (United States)

    Tabib-Azar, Massood

    1991-01-01

    The transient conductivity of high-resistivity Bridgman-grown Cr-doped GaAs under pulsed monochromatic light is monitored using transverse acoustoelectric voltage (TAV) at 83 K. Keeping the photon flux constant, the height and transient time constant at the TAV are used to calculate the energy dependence of the trap density and its cross section, respectively. Two prominent trap profiles with peak trap densities of approximately 10 to the 17th/cu cm eV near the valence and the conduction bands are detected. These traps have very small capture cross sections in the range of 10 to the -23 to 10 to the -21st cm sq. A phenomenon similar to the persistent photoconductivity with transient time constants in excess of a few seconds in high-resistivity GaAs at T = 83 K is also detected using this technique. These long relaxation times are readily explained by the spatial separation of the photo-excited electron-hole pairs and the small capture cross section and large density of trap distribution near the conduction band.

  20. Fluorescence tomography applied to prostate cancer diagnosis using white pulsed laser

    Science.gov (United States)

    Daures, A.; Boutet, J.; Hervé, L.; Sauze, R.; Puszka, A.; Heinrich, E.; Grenier, N.; Dinten, J. M.

    2013-03-01

    Prostate cancer diagnosis is based on PSA rate measurement and ultrasound guided biopsy. Recently criticized for its lack of specificity, new approaches are currently investigated: MRI, elastography, TEP, NIRS and Time Resolved (TR) fluorescence tomography. The advantage of TR fluorescence tomography relies on its good complementarity with the standard ultrasound protocol and on the possible localization of prostate tumors marked by specific probes. After a first TR system based on a bulky titanium-sapphire laser, we designed a new one taking advantage of a more compact white pulsed laser (supercontinuum). The improved compactness is now fully compatible with clinical environment. The light, filtered by two linear variable filters to select a 770+/-20 nm window, is driven to the transrectal probe which also collects the fluorescence light emitted by the marker. The signal is detected by photomultipliers connected to TCSPC boards. A reconstruction algorithm based on intensities and time of flight allows a fast localization of the fluorophore. We compared the performances of the new white laser system to the previous titanium-sapphire on prostate mimicking phantoms. The laser power delivered on the phantom by the new laser appeared to be suitable to fluorescence measurements, just below cutaneous maximum permitted exposure. The new system allowed us to localize fluorescent inclusions of a fluorescent nanoemulsion at fixed positions inside a prostate mimicking phantom.

  1. Applied multi-pulsed laser in surface treatment and numerical-experimental analysis

    Science.gov (United States)

    Laazizi, Abdellah; Courant, Bruno; Jacquemin, Frédéric; Andrzejewski, Henri

    2011-10-01

    This paper presents a comparison between simulation and experimental results of the melting process of metallic material by a pulsed laser source Nd-YAG. The simulations of temperature and velocity fields of melted material were done by solving the transient heat transfer and fluid-flow equations. Variations of the thermophysical properties were considered. Furthermore, the model included the effects of the surface-tension gradient on the fluid surface and the buoyancy force. The simulation was useful in improving our understanding of the phenomena occurring in the treated material. Using a laser triangulation sensor, an experimental study was also conducted on the surface profile of the melted zones to seek a relationship between the so-called keyhole effect and the laser triangulation measurements. The keyhole effect induced strong surface deformations and often formed cavities, which were undesirable in the surface treatment process. The laser power, energy density, and treatment duration could be optimized to prevent the keyhole effect. The predicted laser melted zone (LMZ) morphology was in good agreement with the corresponding experimental measurements for various irradiation conditions, as long as the keyhole effect did not occur.

  2. Pulsed remote field eddy current technique applied to non-magnetic flat conductive plates

    Science.gov (United States)

    Yang, Binfeng; Zhang, Hui; Zhang, Chao; Zhang, Zhanbin

    2013-12-01

    Non-magnetic metal plates are widely used in aviation and industrial applications. The detection of cracks in thick plate structures, such as multilayered structures of aircraft fuselage, has been challenging in nondestructive evaluation societies. The remote field eddy current (RFEC) technique has shown advantages of deep penetration and high sensitivity to deeply buried anomalies. However, the RFEC technique is mainly used to evaluate ferromagnetic tubes. There are many problems that should be fixed before the expansion and application of this technique for the inspection of non-magnetic conductive plates. In this article, the pulsed remote field eddy current (PRFEC) technique for the detection of defects in non-magnetic conducting plates was investigated. First, the principle of the PRFEC technique was analysed, followed by the analysis of the differences between the detection of defects in ferromagnetic and non-magnetic plain structures. Three different models of the PRFEC probe were simulated using ANSYS. The location of the transition zone, defect detection sensitivity and the ability to detect defects in thick plates using three probes were analysed and compared. The simulation results showed that the probe with a ferrite core had the highest detecting ability. The conclusions derived from the simulation study were also validated by conducting experiments.

  3. Influence of applied voltage on the performance of bioelectrochemical anaerobic digestion of sewage sludge and planktonic microbial communities at ambient temperature.

    Science.gov (United States)

    Feng, Qing; Song, Young-Chae; Bae, Byung-Uk

    2016-11-01

    The influence of applied voltage on the bioelectrochemical anaerobic digestion of sewage sludge was studied at ambient temperature (25±2°C). The stability of the bioelectrochemical anaerobic digestion was considerably good in terms of pH, alkalinity and VFAs at 0.3V and 0.5V, but VFA accumulation occurred at 0.7V. The specific methane production rate (370mLCH4/L.d) was the highest at 0.3V, but the methane content (80.6%) in biogas and the methane yield (350mLCH4/gCODr) were higher at 0.5V, significantly better than those of 0.7V. The VS removal efficiency was 64-66% at 0.3V and 0.5V, but only 31% at 0.7V. The dominant species of planktonic microbial communities was Cloacamonas at 0.3V and 0.5V, but the percentage of hydrolytic bacteria species such as Saprospiraceae, Fimbriimonas, and Ottowia pentelensis was much higher at 0.7V. The optimal applied voltage for bioelectrochemical anaerobic digestion was 0.3-0.5V according to digestion performance and planktonic microbial communities.

  4. Reconsideration of the galvanostatic double-pulse method

    NARCIS (Netherlands)

    Kooijman, D.J.; Sluyters, J.H.

    1967-01-01

    A critical examination is made of the voltage response of a cell when a double-pulse current is applied. The limitations of the double-pulse method for studying fast electrode reactions are considered and it is shown that the maximum value of the heterogeneous rate constant measurable with this meth

  5. Development of theoretical approach for describing electronic properties of hetero-interface systems under applied bias voltage

    Science.gov (United States)

    Iida, Kenji; Noda, Masashi; Nobusada, Katsuyuki

    2017-02-01

    We have developed a theoretical approach for describing the electronic properties of hetero-interface systems under an applied electrode bias. The finite-temperature density functional theory is employed for controlling the chemical potential in their interfacial region, and thereby the electronic charge of the system is obtained. The electric field generated by the electronic charging is described as a saw-tooth-like electrostatic potential. Because of the continuum approximation of dielectrics sandwiched between electrodes, we treat dielectrics with thicknesses in a wide range from a few nanometers to more than several meters. Furthermore, the approach is implemented in our original computational program named grid-based coupled electron and electromagnetic field dynamics (GCEED), facilitating its application to nanostructures. Thus, the approach is capable of comprehensively revealing electronic structure changes in hetero-interface systems with an applied bias that are practically useful for experimental studies. We calculate the electronic structure of a SiO2-graphene-boron nitride (BN) system in which an electrode bias is applied between the graphene layer and an electrode attached on the SiO2 film. The electronic energy barrier between graphene and BN is varied with an applied bias, and the energy variation depends on the thickness of the BN film. This is because the density of states of graphene is so low that the graphene layer cannot fully screen the electric field generated by the electrodes. We have demonstrated that the electronic properties of hetero-interface systems are well controlled by the combination of the electronic charging and the generated electric field.

  6. Compact repetitive high voltage nanosecond pulse generator%紧凑型重复频率高压纳秒脉冲电源及其仿真模型

    Institute of Scientific and Technical Information of China (English)

    庞磊; 陈纲亮; 何堃; 任保忠; 张乔根

    2012-01-01

    纳秒脉冲等离子体在诸多实际的工程应用中依赖于小型化且可靠的纳秒脉冲电源实现.设计了一种紧凑型全固态高压纳秒脉冲电源,该电源主要由直流电源部分、绝缘栅双极晶体管及其驱动控制电路、可饱和脉冲变压器、磁脉冲压缩网络等组成.通过理论计算分析、PSpice电路仿真以及实验研究表明,其最终可以在800 Ω的输出负载阻抗上获得幅值40 kV、脉冲宽度100 ns左右、脉冲上升沿约50 ns的高电压脉冲,重复频率最高可达5 kHz.%The application of nanosecond discharge plasma in many fields depends greatly on a compact repetitive high voltage nanosecond pulse generator. In this paper. a compact high voltage nanosecond pulse generator is presented > which is constructed with all-solid-state components. The pulse generator consists of DC module, insulated-gate bipolar transistors and its drivers, saturable pulse transformer and magnetic switch and so on. Simulation analysis and experimental investigation show that, the pulse generator can output pulsed voltage of 40 kV with duration about 100 ns and rise-time of 50 ns. Its highest repetitive frequency can be up to 5 kHz.

  7. Design of sewage treatment system based on high-voltage pulsed electric field technology%基于高压脉冲电场技术的污水处理系统研究设计

    Institute of Scientific and Technical Information of China (English)

    李唐; 王亚伟; 赵振良; 尤丽华

    2013-01-01

    针对污水处理厂剩余污泥含水率高,达到70%-80%,不利于进一步处理的问题,根据污水成分及其处理工艺特点,提出了一种基于高压脉冲电场技术的污水处理的方法.本文从理论上系统地阐述了高压脉冲电场处理装置的研制,设计了低成本高压脉冲电源,最高电压10 kV,最大电流50A,并且能方便的调节电场参数.%Contrary to the problem that the high moisture content of the excess sludge of the sewage treatment plant, up to 70% to 80% , the paper proposed a sewage treatment method based on the high-voltage pulse electric field (HPEF) technology, according to the composition of sewage and the feature of its treatment technology.The paper systematically expounded of how to design a pulsed electric field theoretically,and design a low-cost high-voltage pulse power supply with the peak impulse voltage 10 kV and impulse current to 50 A, which also can easily adjust the electric field parameters.

  8. Inverted Fuel Cell: Room-Temperature Hydrogen Separation from an Exhaust Gas by Using a Commercial Short-Circuited PEM Fuel Cell without Applying any Electrical Voltage.

    Science.gov (United States)

    Friebe, Sebastian; Geppert, Benjamin; Caro, Jürgen

    2015-06-26

    A short-circuited PEM fuel cell with a Nafion membrane has been evaluated in the room-temperature separation of hydrogen from exhaust gas streams. The separated hydrogen can be recovered or consumed in an in situ olefin hydrogenation when the fuel cell is operated as catalytic membrane reactor. Without applying an outer electrical voltage, there is a continuous hydrogen flux from the higher to the lower hydrogen partial pressure side through the Nafion membrane. On the feed side of the Nafion membrane, hydrogen is catalytically split into protons and electrons by the Pt/C electrocatalyst. The protons diffuse through the Nafion membrane, the electrons follow the short-circuit between the two brass current collectors. On the cathode side, protons and electrons recombine, and hydrogen is released. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  9. Neuromuscular disruption with ultrashort electrical pulses

    Science.gov (United States)

    Pakhomov, Andrei; Kolb, Juergen F.; Joshi, Ravindra P.; Schoenbach, Karl H.; Dayton, Thomas; Comeaux, James; Ashmore, John; Beason, Charles

    2006-05-01

    Experimental studies on single cells have shown that application of pulsed voltages, with submicrosecond pulse duration and an electric field on the order of 10 kV/cm, causes sudden alterations in the intracellular free calcium concentration, followed by immobilization of the cell. In order to examine electrical stimulation and incapacitation with such ultrashort pulses, experiments on anesthetized rats have been performed. The effect of single, 450 nanosecond monopolar pulses have been compared with that of single pulses with multi-microsecond duration (TASER pulses). Two conditions were explored: 1. the ability to elicit a muscle twitch, and, 2. the ability to suppress voluntary movement by using nanosecond pulses. The second condition is relevant for neuromuscular incapacitation. The preliminary results indicate that for stimulation microsecond pulses are advantageous over nanosecond pulses, whereas for incapacitation, the opposite seems to apply. The stimulation effects seem to scale with electrical charge, whereas the disruption effects don't follow a simple scaling law. The increase in intensity (time of incapacitation) for a given pulse duration, is increasing with electrical energy, but is more efficient for nanosecond than for microsecond pulses. This indicates different cellular mechanisms for incapacitation, most likely subcellular processes, which have been shown to become increasingly important when the pulse duration is shortened into the nanosecond range. If further studies can confirm these initial results, consequences of reduced pulse duration are a reduction in weight and volume of the pulse delivery system, and likely, because of the lower required energy for neuromuscular incapacitation, reduced safety risks.

  10. Investigating Pulsed Discharge Polarity Employing Solid-State Pulsed Power Electronics

    DEFF Research Database (Denmark)

    Davari, Pooya; Zare, Firuz; Blaabjerg, Frede

    2015-01-01

    . In this paper, effects of applied voltage polarity on plasma discharge have been investigated in different mediums at atmospheric pressure. The experiments have been conducted based on high voltage DC power supply and high voltage pulse generator for point-to-point and point-to-plane geometries. Furthermore......, the influence of electric field distribution is analyzed using Finite Element simulations for the employed geometries and mediums. The experimental and simulation results have verified the important role of the applied voltage polarity, employed geometry and medium of the system on plasma generation....... condition plays an important role in maintaining the desired performance. Investigating the system parameters contributed to the generated pulses is an effective way in improving the system performance further ahead. One of these parameters is discharge polarity which has received less attention...

  11. Comparative studies on extraction of laminarin by high voltage pulsed electric fields and traditional method%高压脉冲电场和传统热水法提取海带多糖的比较研究

    Institute of Scientific and Technical Information of China (English)

    刘航; 冯立强; 刘兴江

    2016-01-01

    Orthogonal tests are carried out to determine optimal laminarin extraction technologies by the high voltage pulsed electric fields and the traditional hot water method.The mechanism of the high voltage pulsed electric fields is preliminarily discussed.The optimal conditions of traditional method are:1∶50 of material-liquid ratio,60 ℃ of extraction temperature and 40 minutes of extraction time.The optimal conditions of high voltage pulsed electric fields are:1 ∶ 30 of material-liquid ratio,20 minutes of pulse time,10 kV of electric field intensity and 50 Hz of pulse frequency.Compared with traditional hot water extraction method,the extraction time is shortened by 50% and the extraction ratio is increased by 45% for high voltage pulsed electric field method.%利用正交试验确定了高压电脉冲电场和传统热水法提取海带多糖的方法的最佳工艺,并对2种工艺进行了比较,初步探讨高压脉冲的作用机理.结果表明,传统热水法提取海带多糖的最佳工艺为:海带粉与去离子水的料液比为1∶50,提取温度为60℃,提取时间为40 min.高压脉冲电场的最佳工艺为:海带粉与去离子水的料液比为1∶30,脉冲时间为20 min,脉冲电压为10 kV,脉冲频率为50 Hz.提取时间仅为传统热水法时间的1/2,海带多糖提取率比传统热水法提高45%.

  12. Simple buck/boost voltage regulator

    Science.gov (United States)

    Paulkovich, J.; Rodriguez, G. E.

    1980-01-01

    Circuit corrects low or high supply voltage, produces regulated output voltage. Circuit has fewer components because inductory/transformer combination and pulse-width modulator serve double duty. Regulator handles input voltage variation from as low as one half output voltage to as high as input transistor rating. Solar arrays, fuel cells, and thermionic generators might use this regulator.

  13. A Pulse Transformer for a 10 MW klystron power supply

    CERN Document Server

    Bak, P A; Kobets, V V; Krainov, G S

    2001-01-01

    The design and test results of the Pulse Transformer (PT) for the klystron with a voltage of 120 kV,klystron current of 130 A and a pulse duration of 1.4 ms is presented. The PT design was realized with taking into account the following requirements: no edge effect on the secondary winding; no overvoltage along the secondary winding at the klystron breakdown; random high voltage breakdowns may occur only between metal parts, not on the windings;the sharp voltage edge applied to the primary winding should not cause a turn-to-turn overvoltage.

  14. Behavior of 2 Cell CPV NI-H2 Battery During Pulse Discharge

    Science.gov (United States)

    Gopalakrishna, M. Rao; Vaidyanathan, Hari

    1997-01-01

    A study was carried out to determine the transient voltage behavior of the 2-cell CPV nickel-hydrogen battery with the objective of using the results as a basis for mathematical modeling. The 2-cell CPV battery which is manufactured by Eagle Picher, Inc. for the GOES program yields 18.5 Ah at C/2 rate of discharge at 10 C with a mid-discharge voltage of 2.514 V. The capacity increased with decrease of temperature and a maximum capacity of 22 Ah was obtained at - 5 C. The pulse test consisted of obtaining the voltage profile in the first 20 milliseconds of the one minute pulse discharge at 37 A and pulse discharge was repeated as a function of state-of-charge. The pulse test at 10 C and 20 C provided voltage profiles with the expected decrease in voltage as the pulse was applied. The end of pulse voltage decreased with the state-of-charge. The battery voltage was above 2V at the end of the one-minute pulse at 12% state-of-charge at 10 C. The voltage profile during the 37 A pulse discharge consists of an initial drop in voltage which was independent of the state of charge. The invariability in the value for the initial drop in voltage with state of charge is a very important observation and indicates that towards the end of discharge the dominant resistance is not ohmic in nature. It could be hypothesized from the nature of the voltage transients that the dominant mechanism towards the end of discharge is proton diffusion. The study also shows that the dominant resistance in the voltage plateau during discharge is activation polarization.

  15. Behavior of 2-Cell CPV Ni-H2 Battery During Pulse Discharge

    Science.gov (United States)

    Vaidyanathan, Hari; Rao, Gopalakrishna

    1998-01-01

    A study was carried out to determine the transient voltage behavior of the 2-cell CPV nickel-hydrogen battery with the objective of using the results as a basis for mathematical modeling. The 2-cell CPV battery which is manufactured by Eagle Picher, Inc. for the GOES program yields 18.5 Ah at C/2 rate of discharge at 10 C with a mid-discharge voltage of 2.514 V. The capacity increased with decrease of temperature and a maximum capacity of 22 Ah was obtained at -5 C. The pulse tests consisted of obtaining the voltage profile in the first 20 milliseconds of the one minute pulse discharge at 37 A and pulse discharge was repeated as a function of state-of-charge. The pulse test at 10 C and 20 C provided voltage profiles with the expected decrease in voltage as the pulse was applied. The end of pulse voltage decreased with the state-of-charge. The battery voltage was above 2V at the end of the one-minute pulse at 8 % state-of-charge at 10 C. The voltage profile during the 37 A pulse discharge consists of an initial drop in voltage which was independent of the state of charge. The invariability in the value for the initial drop in voltage with state of charge is a very important observation. The results show that towards the end of discharge the dominant resistance is not ohmic in nature. It could be hypothesized from the nature of the voltage transients that the dominant mechanism towards the end of discharge is proton diffusion. The study also shows that the dominant resistance in the voltage plateau during discharge is activation polarization.

  16. Comparison of pulsed corona plasma and pulsed electric fields for the decontamination of water containing Legionella pneumophila as model organism.

    Science.gov (United States)

    Banaschik, Robert; Burchhardt, Gerhard; Zocher, Katja; Hammerschmidt, Sven; Kolb, Juergen F; Weltmann, Klaus-Dieter

    2016-12-01

    Pulsed corona plasma and pulsed electric fields were assessed for their capacity to kill Legionella pneumophila in water. Electrical parameters such as in particular dissipated energy were equal for both treatments. This was accomplished by changing the polarity of the applied high voltage pulses in a coaxial electrode geometry resulting in the generation of corona plasma or an electric field. For corona plasma, generated by high voltage pulses with peak voltages of +80kV, Legionella were completely killed, corresponding to a log-reduction of 5.4 (CFU/ml) after a treatment time of 12.5min. For the application of pulsed electric fields from peak voltages of -80kV a survival of log 2.54 (CFU/ml) was still detectable after this treatment time. Scanning electron microscopy images of L. pneumophila showed rupture of cells after plasma treatment. In contrast, the morphology of bacteria seems to be intact after application of pulsed electric fields. The more efficient killing for the same energy input observed for pulsed corona plasma is likely due to induced chemical processes and the generation of reactive species as indicated by the evolution of hydrogen peroxide. This suggests that the higher efficacy and efficiency of pulsed corona plasma is primarily associated with the combined effect of the applied electric fields and the promoted reaction chemistry.

  17. Estimation of the light output power and efficiency of Xe barrier discharge excimer lamps using a one-dimensional fluid model for various voltage waveforms

    Science.gov (United States)

    Oda, Akinori; Sugawara, Hirotake; Sakai, Yosuke; Akashi, Haruaki

    2000-06-01

    Xe dielectric barrier discharges at different gap lengths under applied pulse voltages with trapezoidal and sinusoidal waveforms were simulated using a self-consistent one-dimensional fluid model. In both waveforms, the light output power depended not only on the amplitude of voltage waveforms but also on the discharge gap length. At the narrower discharge gap, the light output efficiency was improved by increasing the time gradient of the applied voltage when the trapezoidal pulse is applied, and by decreasing the duty ratio in the sinusoidal case. In the present simulation, we adopted a fast numerical method for calculation of electric field introducing an exact expression of the discharge current.

  18. Characteristics of SF6 Switch with a Small Gap under High Pressure and Nanosecond Pulse

    Institute of Scientific and Technical Information of China (English)

    TANG Junping; QIU Aici; BO Haiwang; DONG Qinxiao; HE Xiaoping

    2009-01-01

    Structural design and tests on the characteristics of the SFs gas switch with a small gap are presented. This kind of switch often works under high pressure and nanosecond pulse for getting pulse with faster risetime. The breakdown voltage and breakdown delay of a number of switches with different geometries, gas pressures and pulse waveforms were investigated.Experimental results suggested that the breakdown voltage increases linearly with the gas pressure,and the breakdown delay decreases with an increase in the gas pressure and a reduction in the gap distance of the switch under the same applied pulse. By using this kind of switch with a gap of 3 mm as a peaking switch, a pulse generator can provide an output voltage with a peak voltage of 300 kV and a risetime of 3 ns on a resistance load of 150 Ω.

  19. Influence of potential pulses amplitude sequence in a voltammetric electronic tongue (VET) applied to assess antioxidant capacity in aliso.

    Science.gov (United States)

    Fuentes, Esteban; Alcañiz, Miguel; Contat, Laura; Baldeón, Edwin O; Barat, José M; Grau, Raúl

    2017-06-01

    Four signals configurations were studied, two of them built by small increases of potential and two with bigger increments. The highest current values were obtained when pulses with bigger change of potential were used although the best results were shown by the pulse sequence which included an intermediate pulse before the relevant pulse. A mathematical model based on trolox pattern was developed to predict antioxidant capacity of aliso, employing information obtained from all the electrodes, although model validation could be done only employing the information from gold electrode. Copyright © 2016 Elsevier Ltd. All rights reserved.

  20. A compact, all solid-state LC high voltage generator.

    Science.gov (United States)

    Fan, Xuliang; Liu, Jinliang

    2013-06-01

    LC generator is widely applied in the field of high voltage generation technology. A compact and all solid-state LC high voltage generator based on saturable pulse transformer is proposed in this paper. First, working principle of the generator is presented. Theoretical analysis and circuit simulation are used to verify the design of the generator. Experimental studies of the proposed LC generator with two-stage main energy storage capacitors are carried out. And the results show that the proposed LC generator operates as expected. When the isolation inductance is 27 μH, the output voltage is 1.9 times larger than the charging voltage on single capacitor. The multiplication of voltages is achieved. On the condition that the primary energy storage capacitor is charged to 857 V, the output voltage of the generator can reach to 59.5 kV. The step-up ratio is nearly 69. When self breakdown gas gap switch is used as main switch, the rise time of the voltage pulse on load resistor is 8.7 ns. It means that the series-wound inductance in the discharging circuit is very small in this system. This generator can be employed in two different applications.

  1. 前近贴脉冲电压对三代微光像增强器halo效应的影响%Effect of pro-proximity pulse voltage on the third-generation low light level image intensifiers halo effect

    Institute of Scientific and Technical Information of China (English)

    任玲; 石峰; 郭晖; 崔东旭; 史继芳; 钱芸生; 王洪刚; 常本康

    2013-01-01

    In order to explore the proper working voltage for the third-generation low light level image intensifies the influence of pro-proximity pulse voltage on image intensifier halo effect is investigated. The pulse voltage is applied to photocathode of image intensi-fier. Respectively change the high and low level voltage and duty ratio, image intensifier halo images are collected by high-resolution charge-coupled device (CCD). The gray distributions for pixel points on halo image central line are given and comparatively analyzed. The results show that as high level voltage and duty ratio increase, the number of pixel points whose gray value is 255 increases and the border between signal and background becomes clear. When high level voltage is above 200 V and duty ratio is above 60%, the pro-proximity voltage has not great influence on image intensifier halo effect. When low level voltage is above 2 V, photoelectrons escaping from photocathode cannot reach microchannel plate under low level voltage stage. The present investigation is beneficial to the exploration of the optimal working voltage for image intensifier and energy range of photoelectrons escaping from photocathode, and provides an experimental support for the improvement of the third-generation low light level image intensifier performance.%为了探讨三代微光像增强器的合适工作电压,研究了前近贴脉冲电压对微光像增强器halo效应的影响.将脉冲电压信号加在光电阴极上,分别改变脉冲信号的高低电平电压幅值和占空比,利用高分辨率CCD采集了微光像增强器的halo图像,对比分析了halo图像中心线上各像素点对应的灰度值分布和光子计数.研究结果表明,随着高电平电压幅值和占空比的提高,灰度值为255的像素点数目变多,halo图像中背景和信号的边界越来越清晰.当前近贴电压增加到200 V以上和占空比大于60%左右时,其对三代微光像增强器halo图像中心线上各像

  2. Graphene-coated hollow fiber membrane as the cathode in anaerobic electrochemical membrane bioreactors – Effect of configuration and applied voltage on performance and membrane fouling

    KAUST Repository

    Werner, Craig M.

    2015-12-22

    Electrically conductive, graphene-coated hollow-fiber porous membranes were used as cathodes in anaerobic electrochemical membrane bioreactors (AnEMBRs) operated at different applied voltages (0.7 V and 0.9 V) using a new rectangular reactor configuration, compared to a previous tubular design (0.7 V). The onset of biofouling was delayed and minimized in rectangular reactors operated at 0.9 V, compared to those at 0.7 V due to higher rates of hydrogen production. Maximum transmembrane pressures for the rectangular reactor were only 0.10 bar (0.7 V) or 0.05 bar (0.9 V) after 56 days of operation, compared to 0.46 bar (0.7 V) for the tubular reactor after 52 days. The thickness of the membrane biofouling layer was approximately 0.4 µm for rectangular reactors and 4 µm for the tubular reactor. Higher permeate quality (TSS = 0.05 mg/L) was achieved in the rectangular AnEMBR than the tubular AnEMBR (TSS = 17 mg/L), likely due to higher current densities that minimized the accumulation of cells in suspension. These results show that the new rectangular reactor design, which had increased rates of hydrogen production, successfully delayed the onset of cathode biofouling and improved reactor performance.

  3. 高压脉冲电参数对果蔬介电特性的影响机理分析%Influence Mechanism of High-voltage Pulsed Electric Parameters on Dielectric Properties of Fruits and Vegetables

    Institute of Scientific and Technical Information of China (English)

    马飞宇; 郭玉明

    2013-01-01

    The high voltage pulse electric field pretreatment can improve the freeze-drying rate of fruits and vegetables and reduce energy consumption .But when researching fruit and vegetable dielectric property about the changes of on -line monitoring freeze-dried moisture content ,high-voltage pulsed electric field should be considered the influence of electri-cal parameter on dielectric properties of fruit and vegetable .In the cellular level , high-voltage pulsed electric fields effects fruits and vegetables , analyzing the influence of electric parameters on dielectric properties of fruit and vegetable . For equivalent circuit model of fruits and vegetables biological tissue , electrical parameters influence on dielectric proper-ties of fruit and vegetable , such as fruit and vegetable equivalent capacitance and equivalent impedance , which were summarized and analyzed about mechanism to provide a reference on high voltage pulse electric field pretreatment fruit and vegetable processing parameters optimization .%高压脉冲电场预处理果蔬可以提高果蔬冻干速率、降低能耗。但研究运用果蔬介电特性在线监测冻干水分变化时,需要考虑高压脉冲电场电参数对果蔬介电特性的影响。为此,针对高压脉冲电场作用果蔬细胞层面,分析了电参数对果蔬介电特性的影响,对果蔬生物组织等效电路模型和电参数对果蔬等效电容、等效阻抗等介电特性的影响等方面进行了综述分析及机理分析,为高压脉冲电场预处理果蔬工艺参数优化提供了参考。

  4. 应用负高压脉冲技术提高植物空气净化能力的探讨%Application of Negative High-voltage Pulse Technology to Improve Air Purification Ability of Plants

    Institute of Scientific and Technical Information of China (English)

    杨运经; 习岗; 刘锴; 张晓辉

    2011-01-01

    现代城市中的室内空气污染日益严重,室内空气污染的净化与治理已成为社会发展中迫切需要解决的关键科技问题之一.为此,根据植物电信号的低频特征与电共振原理,利用极低频负高压脉冲连续刺激盆栽吊兰植物的根际土壤,使吊兰叶片产生了显著的空气负离子倍增效应.在此基础上依据评价空气质量的常用指标:单极系数q、安培空气质量评价系数CI、空气负离子系数P和森林空气离子评价指数FCI,对应用负高压脉冲技术提高植物的空气净化能力进行了计算与分析.结果表明,极低频负高压脉冲电场可以有效地提高植物的空气净化能力,提出了极低频负高压脉冲电场介导的植物空气净化新技术.%Purification of indoor air pollution has become one of the key technologies of social development. An extremely low frequency high voltage pulse generator was designed according to the characteristics of plants electrical signals and the principle of electrical resonance. The soil of potted broadleaf bracket-plant (Chlorophytum como-sum) was continuously stimulated by negative high voltage pulses with very low frequency, the high concentration of negative air ions appeared around the plant leaves, and the multiplier effect of negative air ion from leave of broadleaf bracket-plant was produced. Then, the ability of plant air purification was calculated and analyzed according to common evaluation indicators of air quality such as single polar factor q, air quality assessment coefficient CI, negative ion air coefficient P and the forest air ion evaluation index FCI. The results show that the extremely low-frequency negative high voltage pulse can enhance the ability of plant to air purification. A new technology of indoor air pollution control and restoration based on negative high-voltage pulse technology is proposed.

  5. The use of ultrasonic pulse velocity tests for the diagnosis of ancient masonries: the influence of the applied load

    Science.gov (United States)

    Leucci, Giovanni; Vasanelli, Emilia; Calia, Angela; Micelli, Francesco; Aiello, Maria Antonietta

    2014-05-01

    Sophisticated non destructive techniques for the diagnosis of existing masonry structures have been developed and improved throughout the years, such as ground penetrating radar, thermography, sonic and ultrasonic tomography, laser scanner survey, etc.: by using an integrated approach it is possible to reconstruct the morphology of the masonry walls, to detect the presence of cracks and voids, achieving an accurate and reliable diagnosis of the construction, which is the basis for the restoration design. The ultrasonic pulse velocity (UPV) method can be conveniently used to check the quality of stones, but it can be used also for material characterization. Both the intrinsic characteristic of the stone (porosity, grain size, anisotropy, etc.) and the external factors (humidity, stress, temperature, presence of cracks) may affect the elastic wave propagation, thus in order to correctly estimate the ultrasonic behaviour of the material investigated it is important to know in what manner and how much the variation of the experimental conditions may modify the characteristics of the waves being measured. This aspect is of crucial importance when in situ measurements are made. In this work the influence of the applied load on UPV results has been investigated. In particular, the research has been carried out on ashlars and on sample masonry panels made of lime mortar joints and Lecce stone, a soft calcarenitic stone traditionally used in the Lecce district, South of Italy. The presence of load strongly influenced the UPV measures, due to the particular microstructural characteristic of the stone. The work aim at quantify this influence in order to correctly interpret in situ measurements.

  6. A SVPWM based on fluctuate capacitor voltage in 3L-NPC back-to-back converter applied to wind energy

    DEFF Research Database (Denmark)

    Chen, Quan; Wang, Qunjing; Chen, Zhe

    2014-01-01

    Three-level Neutral-point-clamped (3L-NPC) converters are becoming a realistic alternative to the conventional converters in high-power wind-energy applications. But the unbalance in the supported capacitors' voltage of back-to-back 3L-NPC converters, including the dynamics of the capacitors...... between the fluctuate voltage of upper and lower capacitors is extracted. Based on this error factor the duty-time of every active voltage vector is calculated. In order to validate the model and the control strategy proposed in this paper, a 2MW 3L-NPC converter used in wind energy has been simulated....

  7. Square pulse linear transformer driver

    Directory of Open Access Journals (Sweden)

    A. A. Kim

    2012-04-01

    Full Text Available The linear transformer driver (LTD technological approach can result in relatively compact devices that can deliver fast, high current, and high-voltage pulses straight out of the LTD cavity without any complicated pulse forming and pulse compression network. Through multistage inductively insulated voltage adders, the output pulse, increased in voltage amplitude, can be applied directly to the load. The usual LTD architecture [A. A. Kim, M. G. Mazarakis, V. A. Sinebryukhov, B. M. Kovalchuk, V. A. Vizir, S. N Volkov, F. Bayol, A. N. Bastrikov, V. G. Durakov, S. V. Frolov, V. M. Alexeenko, D. H. McDaniel, W. E. Fowler, K. LeCheen, C. Olson, W. A. Stygar, K. W. Struve, J. Porter, and R. M. Gilgenbach, Phys. Rev. ST Accel. Beams 12, 050402 (2009PRABFM1098-440210.1103/PhysRevSTAB.12.050402; M. G. Mazarakis, W. E. Fowler, A. A. Kim, V. A. Sinebryukhov, S. T. Rogowski, R. A. Sharpe, D. H. McDaniel, C. L. Olson, J. L. Porter, K. W. Struve, W. A. Stygar, and J. R. Woodworth, Phys. Rev. ST Accel. Beams 12, 050401 (2009PRABFM1098-440210.1103/PhysRevSTAB.12.050401] provides sine shaped output pulses that may not be well suited for some applications like z-pinch drivers, flash radiography, high power microwaves, etc. A more suitable power pulse would have a flat or trapezoidal (rising or falling top. In this paper, we present the design and first test results of an LTD cavity that generates such a type of output pulse by including within its circular array a number of third harmonic bricks in addition to the main bricks. A voltage adder made out of a square pulse cavity linear array will produce the same shape output pulses provided that the timing of each cavity is synchronized with the propagation of the electromagnetic pulse.

  8. The effect of applied control strategy on the current-voltage correlation of a solid oxide fuel cell stack during dynamic operation

    Directory of Open Access Journals (Sweden)

    Szmyd Janusz S.

    2014-09-01

    Full Text Available This paper discusses the transient characteristics of the planar type SOFC cell stack, of which the standard output is 300 W. The transient response of the voltage to the manipulation of an electric current was investigated. The effects of the response and of the operating condition determined by the operating temperature of the stack were studied by mapping a current-voltage (I-V correlation. The current-based fuel control (CBFC was adopted for keeping the fuel utilization factor at constant while the value of the electric current was ramped at the constant rate. The present experimental study shows that the transient characteristics of the cell voltage are determined by primarily the operating temperature caused by the manipulation of the current. Particularly, the slope of the I-V curve and the overshoot found on the voltage was remarkably influenced by the operating temperature. The different values of the fuel utilization factor influence the height of the settled voltages. The CBFC has significance in determining the slope of the I-V characteristic, but the different values ofthe fuel utilization factor does not affect the slope as the operating temperature does. The CBFC essentially does not alter the amplitude of the overshoot on the voltage response, since this is dominated by the operating temperature and its change is caused by manipulating the current.

  9. Simulation and Modeling of 24-Pulse STATCOM in EMTDC/PSCAD Program in Order to Regulate Voltage and Dynamic Stability Improvement

    Directory of Open Access Journals (Sweden)

    Naser Parhizgar

    2012-02-01

    Full Text Available This study starts from the proof of Low Frequency Oscillation (LFO and then points out that there are many ways to study the LFO including its rejection measures. Also in this study one control system is planned in order to regulate voltage at common coupling point (PCC in where STATCOM is installed. This research present a single-machine infinite-bus system with one static synchronous compensator (STATCOM asymmetrically installed as a current source. Together with a classical generator model, the simplest power equation is obtained to give direct and clear physical concepts on synchronizing and damping torque factors. According to the primary equations, some basic issues, such as the relationship of voltage gain control and damping control, operating conditions, and the installation of STATCOM, are investigated in this research. Then, with assistance of proportional controller for voltage regulation and damp control, the digital simulation indicate the necessity of control of STATCOM in damping power system oscillations and supplying regulated voltage support.

  10. High voltage pulse electron beam control strategy and influence on weld bead shape%高压脉冲电子束的控制及其对焊缝形貌影响

    Institute of Scientific and Technical Information of China (English)

    许海鹰; 余伟; 左从进

    2011-01-01

    研制出一台150 kV/30 kW高压脉冲电子束焊机,介绍了控制脉冲束流产生的偏压脉冲电源拓扑电路结构及脉冲束流频率、占空比、束流基值、束流峰值的调节控制技术.在0~1 kHz频率范围内,该电源可输出最大幅值200 mA的脉冲电子束束流,且工艺参数调节方便.分别采用脉冲束流与连续束流电子束工艺焊接了1Cr18Ni9Ti奥氏体不锈钢,对不同工艺的焊缝形貌进行了对比分析.与连续束流电子束焊接工艺相比,采用脉冲电子束焊接工艺的焊缝熔深增加,深宽比增大;对于脉冲电子束焊接工艺,占空比给定时,随着束流频率增加,焊接缺陷减少.试验结果表明:脉冲束流频率、占空比是影响焊缝成形的关键工艺参数;脉冲调制方式控制偏压是获得高压脉冲电子束的理想控制技术之一.%A 150 kV/30 kW high voltage pulse electron beam welding power source was developed.The bias pulse power source topology and control technique about base beam current,peak beam current,pulse beam duty,pulse beam frequency were introduced.Not only the biggest peak beam current up to 200 mA has been exported by this power source at 0-1 kHz,but also weld technology parameters are expediently adjusted.The 1Cr18Ni9Ti stainless steel work pieces had been welded by electron beam welding and pulse electron beam welding.These weld bead shapes had been studied and analyzed.In contrast with electron beam welding,weld penetration will be increased by pulse electron beam welding introduced.At the immovable pulse beam duty,the weld faults will be reduced with the pulse beam frequency being increased.Through these weld tests,besides beam frequency and duty are substantiated key technique parameters for weld shapes,it also shows that pulse modulated bias power source technique is an applicable technology to achieve high voltage pulse electron beam.

  11. Research of reduced common-mode voltage technique with nonzero vector pulse width modulation for three-phase inverters%三相逆变器的无零矢量共模电压抑制技术研究

    Institute of Scientific and Technical Information of China (English)

    章勇高; 邝光健; 龙立中

    2013-01-01

    The common-mode suppression techniques with nonzero vector pulse width modulation (NZPWM) for three-phase inverters are studied. They are random state pulse width modulation (RSPWM), active zero state PWM1 (AZSPWM1), active zero state PWM3 (AZSPWM3) and near state PWM (NSPWM). Firstly, the operation areas of modulation factor and reference voltage vector with different modulation strategies are analyzed. The results show that RSPWM has a smaller operation area than other three NZPWM and is suitable for the application with lower modulation ratio. Secondly, the DC voltage utilization rate and output harmonic of different NZPWM are researched and compared with that of traditional space vector modulation (SVM) by using theoretical analysis and simulation. The results show that AZPWM1, AZPWM3 and NSPWM can not only suppress the common mode voltage of three-phase inverters efficiently, but also maintain high DC voltage utilization rate. However, three-phase inverters with NSPWM have the higher output harmonic comparing with the traditional SVM. The research results provide theoretical basis and instruction for the selection of common mode voltage suppression technique with NZPWM for three-phase inverters and its further study.%  研究了三相逆变器的 RSPWM、AZSPWM1、AZSPWM3和 NSPWM 无零矢量共模电压抑制技术。首先,分析了不同调制策略的调制因数和参考电压矢量的工作区间,说明了 RSPWM 的工作区间较小,适用于低调制比工作场合。再次,利用理论分析和仿真方法,研究了无零矢量调制策略的直流电压利用率和输出谐波特性,并与传统 SVM 调制策略比较。结果表明,AZSPWM1、AZSPWM3和 NSPWM 调制策略能够有效地抑制三相逆变器共模电压,同时保持了较高的直流电压利用率。但相对 SVM 调制策略,三相逆变器的输出谐波含量有所增大。研究结果为三相逆变器的无零矢量共模电压抑制技术的选用及进一步研究提供了理论依据和指导。

  12. Experimental Study of SO2 Removal by Pulsed DBD Along with the Application of Magnetic Field

    Institute of Scientific and Technical Information of China (English)

    RONG Ming-zhe; LIU Ding-xin; WANG Xiao-hua; WANG Jun-hua

    2007-01-01

    Dielectric barrier discharge (DBD) for SO2 removal from indoor air is investigated.In order to improve the removal efficiency,two novel methods are combined in this paper,namely by applying a pulsed driving voltage with nanosecond rising time and applying a magnetic field.For SO2 removal efficiency,different matches of electric field and magnetic field are discussed.And nanosecond rising edge pulsed power supply and microsecond rising edge pulsed power supply are compared.It can be concluded that a pulsed DBD with nanosecond rising edge should be adopted,and electrical field and magnetic field should be applied in an appropriate match.

  13. 动态电压恢复器的快速检测及补偿策略%Fast Detection and Compensation Strategy Applied for Dynamic Voltage Restorer

    Institute of Scientific and Technical Information of China (English)

    杨浩; 王宇; 石巍; 方太勋; 刘为群

    2015-01-01

    Low voltage ride through(LVRT)is an important technical problem for power quality.In order to study LVRT,this paper designed an LVRT experimental system composed of dynamic voltage restorer(DVR),and used voltage dq integrated value and its change rate as detection criterion for voltage drops,and used the voltage feed forward and resonance control loop as the compensation strategy,which can achieve fast compensation of low voltage power grid fault.The experiment is completed using above platform.The test results show that DVR which adopts above detection and compensation strategy can achieve the compensation for low voltage fault quickly.%为了研究低电压穿越问题,设计了一套由动态电压恢复器组成的低电压穿越试验系统。提出采用电压 dq 综合值结合其变化率作为低电压故障发生检测判据,采用电压差前馈结合谐振控制环作为补偿策略,实现对电网低电压故障的快速补偿。经电压补偿试验表明,采用上述低电压故障检测及补偿策略的动态电压恢复器能够快速实现电压补偿。

  14. 基于固体开关器件的新型高压脉冲驱动源%New high-voltage pulse driving source based on solid switch device

    Institute of Scientific and Technical Information of China (English)

    陈静; 周晓青

    2012-01-01

    The the circuit of the pulse source is introduced briefly. The switch theory of the power MOSFET is expatiated emphatically. The overdriving technique of the power MOSFET grid is investigated to improve the switch speed of the power MOSFET by simulation and experiments. Power MOSFET is used as a switch element in the technology. The ways of improving the output power of the pulse source are analyzed through integrating the techniques of several power MOSFETs in series or in parallel. A high-voltage wide pulse source with the amplitude of output pulse larger than 4 kv, the rise time less than 10 ns and the pulse width wider than 100 ns was obtained.%从MOSFET的开关基理,以仿真与电路实验相结合的方法,研究出了MOSFET栅极的“过”驱动技术,以此来提高MOSFET的开关速度.并结合多个MOSFET的串并联的级联技术,采用多管串联方法来提高脉冲源的输出脉冲幅度,采用多管并联方法来提高脉冲源的其输出脉冲功率,从而得到较大的脉冲宽度.在此研制出了输出脉冲幅度大于4kV、前沿小于10ns、脉冲宽度大于100ns的高压快脉冲源.

  15. Programmable pulse generator

    CERN Document Server

    Xue Zhi Hua; Duan Xiao Hui

    2002-01-01

    The author introduces the design of programmable pulse generator that is based on a micro-controller and controlled by RS232 interface of personal computer. The whole system has good stability. The pulse generator can produce TTL pulse and analog pulse. The pulse frequency can be selected by EPLD. The voltage amplitude and pulse width of analog pulse can be adjusted by analog switches and digitally-controlled potentiometers. The software development tools of computer is National Instruments LabView5.1. The front panel of this virtual instrumentation is intuitive and easy-to-use. Parameters can be selected and changed conveniently by knob and slide

  16. CHARACTERISTICS OF A FAST RISE TIME POWER SUPPLY FOR A PULSED PLASMA REACTOR FOR CHEMICAL VAPOR DESTRUCTION

    Science.gov (United States)

    Rotating spark gap devices for switching high-voltage direct current (dc) into a corona plasma reactor can achieve pulse rise times in the range of tens of nanoseconds. The fast rise times lead to vigorous plasma generation without sparking at instantaneous applied voltages highe...

  17. Elimination of DC-Link Current Ripple for Modular Multilevel Converters With Capacitor Voltage-Balancing Pulse-Shifted Carrier PWM

    DEFF Research Database (Denmark)

    Deng, Fujin; Chen, Zhe

    2015-01-01

    The modular multilevel converter (MMC) is attractive for medium- and high-power applications because of its high modularity, availability, and power quality. In this paper, the current ripple on the dc link of the three-phase MMC derived from the phase-shifted carrier-based pulse-width modulation...

  18. Suppression of endurance degradation by applying constant voltage stress in one-transistor and one-resistor resistive random access memory

    Science.gov (United States)

    Su, Yu-Ting; Chang, Ting-Chang; Tsai, Tsung-Ming; Chang, Kuan-Chang; Chu, Tian-Jian; Chen, Hsin-Lu; Chen, Min-Chen; Yang, Chih-Cheng; Huang, Hui-Chun; Lo, Ikai; Zheng, Jin-Cheng; Sze, Simon M.

    2017-01-01

    In this letter we demonstrate an operation method that effectively suppresses endurance degradation. After many operations, the off-state of resistance random access memory (RRAM) degrades. This degradation is caused by reduction of active oxygen ions participating in the set process, as determined by current fitting of current-voltage (I-V) curves obtained from the endurance test between the interval of seventy to one hundred million operations. To address this problem, we propose the application of constant voltage stress after every five million operations during the endurance test. The experimental result shows that this method can maintain oxygen ions at the proper depth in the electrode and improve RRAM reliability.

  19. Voltage-Driven Magnetization Switching and Spin Pumping in Weyl Semimetals

    Science.gov (United States)

    Kurebayashi, Daichi; Nomura, Kentaro

    2016-10-01

    We demonstrate electrical magnetization switching and spin pumping in magnetically doped Weyl semimetals. The Weyl semimetal is a three-dimensional gapless topological material, known to have nontrivial coupling between the charge and the magnetization due to the chiral anomaly. By solving the Landau-Lifshitz-Gilbert equation for a multilayer structure of a Weyl semimetal, an insulator and a metal while taking the charge-magnetization coupling into account, magnetization dynamics is analyzed. It is shown that the magnetization dynamics can be driven by the electric voltage. Consequently, switching of the magnetization with a pulsed electric voltage can be achieved, as well as precession motion with an applied oscillating electric voltage. The effect requires only a short voltage pulse and may therefore be energetically favorable for us in spintronics devices compared to conventional spin-transfer torque switching.

  20. Shearography and pulsed stimulated infrared thermography applied to a nondestructive evaluation of FRP strengthening systems bonded on concrete structures

    OpenAIRE

    Taillade, Frédéric; Quiertant, Marc; Benzarti, Karim; Aubagnac, Christophe

    2011-01-01

    This paper presents two complementary techniques, shearography and pulsed stimulated infrared thermography, used to detect and characterize depth and width of the adhesion defects (delaminations or adhesive disbonds) of externally bonded fiber-reinforced polymers (FRP) on concrete surface structures. Shearography associated to a depressure load on the one hand, and step heating infrared thermography on the other hand are presented. In a first step, the feasibility study of the two methods is ...

  1. A spatial model with pulsed releases to compare strategies for the sterile insect technique applied to the mosquito Aedes aegypti.

    Science.gov (United States)

    Oléron Evans, Thomas P; Bishop, Steven R

    2014-08-01

    We present a simple mathematical model to replicate the key features of the sterile insect technique (SIT) for controlling pest species, with particular reference to the mosquito Aedes aegypti, the main vector of dengue fever. The model differs from the majority of those studied previously in that it is simultaneously spatially explicit and involves pulsed, rather than continuous, sterile insect releases. The spatially uniform equilibria of the model are identified and analysed. Simulations are performed to analyse the impact of varying the number of release sites, the interval between pulsed releases and the overall volume of sterile insect releases on the effectiveness of SIT programmes. Results show that, given a fixed volume of available sterile insects, increasing the number of release sites and the frequency of releases increases the effectiveness of SIT programmes. It is also observed that programmes may become completely ineffective if the interval between pulsed releases is greater that a certain threshold value and that, beyond a certain point, increasing the overall volume of sterile insects released does not improve the effectiveness of SIT. It is also noted that insect dispersal drives a rapid recolonisation of areas in which the species has been eradicated and we argue that understanding the density dependent mortality of released insects is necessary to develop efficient, cost-effective SIT programmes.

  2. Study on the influence of applied voltage and feed concentration on the performance of electrodeionization in nickel recovery from electroplating wastewater

    Science.gov (United States)

    Wardani, Anita K.; Hakim, Ahmad N.; Khoiruddin, Destifen, Welsen; Goenawan, Albertus; Wenten, I. G.

    2017-01-01

    Wastewaters from electroplating industries are usually contaminated with nickel up to 1000 mg/L. According to environmental regulations worldwide, nickel concentration on wastewaters must be controlled to an acceptable level before being discharged to the environment. This paper offers an alternative way to develop an efficient effluent-free technology to reduce the nickel content of rinse water so that the treated water could be recycled for rinsing and subsequently to workout methodology to recover nickel by electrodeionization (EDI). Electrical voltage and initial nickel concentration were varied to study the effect of the parameters. Results showed that EDI could remove nickel effectively which gives an outstanding result in terms of product quality. Nickel concentration on diluate chamber decreased up to 99% after 60 and 180 minutes for nickel concentration of 300 and 1000 mg/L, respectively. Meanwhile, the increase of electrical voltage led to faster nickel removal.

  3. Phenol wastewater treatment by needle-plate pulsed high voltage discharge in gas-liquid two phase%针-板式高压脉冲气液两相放电降解废水中的苯酚

    Institute of Scientific and Technical Information of China (English)

    董冰岩; 张鹏; 聂亚林; 谢寅寅; 何俊文; 王晖

    2016-01-01

    为了提高脉冲放电对有机物的降解效果,以苯酚为处理对象建立了单针-板电极形式的脉冲放电体系,考察了各因素对苯酚降解的影响并分析了降解过程中间产物及其浓度变化。结果表明,脉冲电压、电极间距、针-液间距、脉冲频率、曝气量等影响因素对苯酚降解率有很大影响;随着脉冲电压的增大,苯酚降解率增大,电压达到一定值后,苯酚降解率增大不再明显,趋于稳定;随着电极间距、针-液间距、脉冲频率、曝气量的增大,苯酚降解率增大,但当这些因素达到一定值后继续增大,苯酚降解率反而降低。100mL浓度为100mg/L的苯酚废水在电极间距10mm、针-液间距7.5mm、脉冲电压26kV、脉冲频率70Hz、曝气量1.5L/min的最佳条件下,放电60min时苯酚降解率为64.63%,放电140min时达到了85.02%。中间产物间苯二酚、对苯二酚、对苯醌、邻苯二酚在放电过程中浓度随着放电时间的延长先增大后减小,最后浓度都趋于零。其中,间苯二酚浓度最低并且分段出现,对苯醌浓度最大,邻苯二酚最先消失,考察产物变化规律以提高苯酚降解的彻底性。%In order to enhance the effect of pulse discharge on degradation of organic matter,a pulse discharge system of single needle-plate electrode aimed at phenol was established. The paper investigated the effect of various factors on phenol degradation and analyzed the degradation of intermediate products and their concentrations in the degradation process. Such factors,as pulse voltage,electrode spacing,needle-liquid spacing,pulse frequency,and air volume,had a great influence on the degradation rate of phenol. Phenol degradation rate increased with the increase of pulse voltage and tended to stablize while pulse voltage reached a specific value. With the increase of electrode spacing,needle-liquid spacing,pulse frequency,air volume,degradation rate of

  4. Observation of applied voltage response of dye-doped liquid crystal by optical measurement of real and imaginary parts of complex refractive index

    Science.gov (United States)

    Sakamoto, Moritsugu; Bannai, Kenta; Noda, Kohei; Sasaki, Tomoyuki; Ono, Hiroshi

    2017-09-01

    The behavior of liquid crystal (LC) molecules and dye molecules in a dye-doped liquid crystal (DDLC) under a voltage application condition was quantitatively investigated. To observe the reorientation of these molecules, the real and imaginary parts of the complex refractive index were simultaneously and individually measured using an optical interferometer. The obtained results indicate that the alignment of dye molecules doped in DDLC occurs following the electrically responding LC molecules, near the Freedericksz transition region of LC.

  5. New digital techniques applied to A and Z identification using pulse shape discrimination of silicon detector current signals

    Energy Technology Data Exchange (ETDEWEB)

    Barlini, S. [LPC Caen, ENSICAEN, University of Caen, CNRS/IN2P3, Caen (France)], E-mail: barlini@fi.infn.it; Bougault, R.; Laborie, Ph.; Lopez, O.; Mercier, D. [LPC Caen, ENSICAEN, University of Caen, CNRS/IN2P3, Caen (France); Parlog, M. [LPC Caen, ENSICAEN, University of Caen, CNRS/IN2P3, Caen (France); NIPNE, RO-76900 Bucharest (Romania); Tamain, B.; Vient, E. [LPC Caen, ENSICAEN, University of Caen, CNRS/IN2P3, Caen (France); Chevallier, E.; Chbihi, A.; Jacquot, B. [GANIL, CEA/DSM-CNRS/IN2P3, Caen (France); Kravchuk, V.L. [INFN-LNL, I-35020 Legnaro, Padova (Italy)

    2009-03-11

    Extending pulse shape discrimination (PSD) to digitized signals is one of the most promising methods to identify particles stopped in a detector. Using the CIME accelerator in the GANIL laboratory, a measurement campaign was done to collect data corresponding to different charges, masses and energies of implanted ions. These data are used to develop an algorithm capable to discriminate the different particles both in mass and charge. In this experiment, a 300{mu}m n-TD reverse mounted Si detector was used. These studies on PSD are part of the FAZIA R and D, a research and development project aiming at building a new 4{pi} array for isospin nuclear physics.

  6. High Light Absorption and Charge Separation Efficiency at Low Applied Voltage from Sb-Doped SnO2/BiVO4 Core/Shell Nanorod-Array Photoanodes.

    Science.gov (United States)

    Zhou, Lite; Zhao, Chenqi; Giri, Binod; Allen, Patrick; Xu, Xiaowei; Joshi, Hrushikesh; Fan, Yangyang; Titova, Lyubov V; Rao, Pratap M

    2016-06-08

    BiVO4 has become the top-performing semiconductor among photoanodes for photoelectrochemical water oxidation. However, BiVO4 photoanodes are still limited to a fraction of the theoretically possible photocurrent at low applied voltages because of modest charge transport properties and a trade-off between light absorption and charge separation efficiencies. Here, we investigate photoanodes composed of thin layers of BiVO4 coated onto Sb-doped SnO2 (Sb:SnO2) nanorod-arrays (Sb:SnO2/BiVO4 NRAs) and demonstrate a high value for the product of light absorption and charge separation efficiencies (ηabs × ηsep) of ∼51% at an applied voltage of 0.6 V versus the reversible hydrogen electrode, as determined by integration of the quantum efficiency over the standard AM 1.5G spectrum. To the best of our knowledge, this is one of the highest ηabs × ηsep efficiencies achieved to date at this voltage for nanowire-core/BiVO4-shell photoanodes. Moreover, although WO3 has recently been extensively studied as a core nanowire material for core/shell BiVO4 photoanodes, the Sb:SnO2/BiVO4 NRAs generate larger photocurrents, especially at low applied voltages. In addition, we present control experiments on planar Sb:SnO2/BiVO4 and WO3/BiVO4 heterojunctions, which indicate that Sb:SnO2 is more favorable as a core material. These results indicate that integration of Sb:SnO2 nanorod cores with other successful strategies such as doping and coating with oxygen evolution catalysts can move the performance of BiVO4 and related semiconductors closer to their theoretical potential.

  7. 阶梯型脉冲电压诱导连续能量质子谱数值仿真%Numerical simulation of proton generation with continuous energy spectrum by pulse voltage with discrete steps

    Institute of Scientific and Technical Information of China (English)

    石经纬; 汪志健; 巩春志; 田修波; 杨士勤

    2011-01-01

    The performance degradation of spacecraft thermal control coatings irradiated by protons is generally investigated by using protons with the same energy in ground testing while the energy of protons is in succession in space. The irradiation e-quivalence of the two kinds of protons is still not well understood. In this paper, a method of producing protons with continuous energy by plasma sheath acceleration using pulse voltage with discrete steps is proposed for better analysis of irradiation equivalence. The dose-energy distribution on the sample is numerically investigated by particle-in-cell(PIC) method. The characteristics of dose-energy distribution and the formation mechanism of protons with continuous energy are then discussed. The results show that protons with continuous energy can be realized utilizing pulse voltage with discrete steps, as the energy of protons irradiating the sample overlaps between two adjacent 1 μs periods, and the energy of protons produced is closely related to the voltage on the sample in every 1 μs period. Moreover, the number of protons irradiating the sample may decrease if the proton energy increases.%热控涂层质子辐照的地面模拟研究中采用单一能量质子替代空间能量连续分布的质子,连续能量质子谱是其等效性研究的关键.提出了采用阶梯型脉冲负偏压鞘层加速技术在一个脉冲宽度内获得连续能量质子谱的方法,并利用质点网格法对所获得质子谱的剂量-能量关系进行了数值仿真研究,分析了连续能量质子谱的剂量-能量分布特征及连续能量质子谱的形成过程.结果表明:阶梯型脉冲负偏压鞘层加速能够产生连续能量的质子谱,连续谱是每微秒区间入射到样品的质子叠加而成的,且每个区间所产生质子的能量与该区间电压值相对应,连续谱中,随着质子能量的增加,其剂量总体上呈现下降的趋势.

  8. SVPWM Technique with Varying DC-Link Voltage for Common Mode Voltage Reduction in a Matrix Converter and Analytical Estimation of its Output Voltage Distortion

    Science.gov (United States)

    Padhee, Varsha

    Common Mode Voltage (CMV) in any power converter has been the major contributor to premature motor failures, bearing deterioration, shaft voltage build up and electromagnetic interference. Intelligent control methods like Space Vector Pulse Width Modulation (SVPWM) techniques provide immense potential and flexibility to reduce CMV, thereby targeting all the afore mentioned problems. Other solutions like passive filters, shielded cables and EMI filters add to the volume and cost metrics of the entire system. Smart SVPWM techniques therefore, come with a very important advantage of being an economical solution. This thesis discusses a modified space vector technique applied to an Indirect Matrix Converter (IMC) which results in the reduction of common mode voltages and other advanced features. The conventional indirect space vector pulse-width modulation (SVPWM) method of controlling matrix converters involves the usage of two adjacent active vectors and one zero vector for both rectifying and inverting stages of the converter. By suitable selection of space vectors, the rectifying stage of the matrix converter can generate different levels of virtual DC-link voltage. This capability can be exploited for operation of the converter in different ranges of modulation indices for varying machine speeds. This results in lower common mode voltage and improves the harmonic spectrum of the output voltage, without increasing the number of switching transitions as compared to conventional modulation. To summarize it can be said that the responsibility of formulating output voltages with a particular magnitude and frequency has been transferred solely to the rectifying stage of the IMC. Estimation of degree of distortion in the three phase output voltage is another facet discussed in this thesis. An understanding of the SVPWM technique and the switching sequence of the space vectors in detail gives the potential to estimate the RMS value of the switched output voltage of any

  9. Note: Galvanic isolated voltage source using a single photodiode.

    Science.gov (United States)

    Stoican, O S

    2010-04-01

    A galvanic isolated voltage source able to provide several volts by using a single photodiode is described. A pulse-modulated laser beam is sent to a photodiode. By using a step-up transformer the amplitude of the variable voltage generated by the photodiode is increased. Adding a rectifier cell the variable voltage is converted back into a dc voltage.

  10. Anisotropic steady-flow hydrodynamic parameters of microporous media applied to pulse tube and Stirling cryocooler regenerators

    Science.gov (United States)

    Clearman, W. M.; Cha, J. S.; Ghiaasiaan, S. M.; Kirkconnell, C. S.

    2008-03-01

    The hydrodynamic parameters associated with steady longitudinal and lateral (radial) flow of helium in several widely-used pulse tube and Stirling cryocooler regenerator fillers were measured and correlated in this investigation. Pressure drops in test sections packed with regenerator fillers were experimentally measured. Computational fluid dynamics (CFD) models of the regenerator test sections and their vicinities were developed and simulations were performed in which the regenerator test sections were modeled as porous media. By iterative repetition of the simulations, the longitudinal and radial permeability and Forchheimer inertial coefficients were determined such that they would lead to agreement between experimental measurements and the simulations. The regenerator fillers included 325 and 400 mesh stainless steel screens, stainless steel metal foam, sintered 400 mesh stainless steel screens, and a stack of micromachined perforated plates. The hydrodynamic response of the regenerator fillers were also correlated as friction factors. The results confirm that the aforementioned regenerator fillers are anisotropic.

  11. Possibility of applying a hydrodynamic model to describe the laser erosion of metals irradiated by high-intensity nanosecond pulses

    Energy Technology Data Exchange (ETDEWEB)

    Kozadaev, K V [A.N. Sevchenko Research Institute of Applied Physics Problems, Belarusian State University, Minsk (Belarus)

    2014-04-28

    We report the results of experimental investigations of the production and development of plasma-vapour plumes upon irradiation of metal targets by nanosecond (10–100 ns) pulses with a high (10{sup 8}–10{sup 10} W cm{sup -2}) power density under atmospheric conditions. The transition from a quasi-stationary thermal mechanism of metal erosion to an explosion hydrodynamic one takes place when the radiation power density increases from 10{sup 8} to 10{sup 9} W cm{sup -2}. The resultant experimental information is extremely important for the laser deposition of metal nanostructures under atmospheric conditions, which is possible only for power densities of 10{sup 8}–10{sup 9} W cm{sup -2}. (interaction of laser radiation with matter)

  12. Transient voltage sharing in series-coupled high voltage switches

    Directory of Open Access Journals (Sweden)

    Editorial Office

    1992-07-01

    Full Text Available For switching voltages in excess of the maximum blocking voltage of a switching element (for example, thyristor, MOSFET or bipolar transistor such elements are often coupled in series - and additional circuitry has to be provided to ensure equal voltage sharing. Between each such series element and system ground there is a certain parasitic capacitance that may draw a significant current during high-speed voltage transients. The "open" switch is modelled as a ladder network. Analy­sis reveals an exponential progression in the distribution of the applied voltage across the elements. Overstressing thus oc­curs in some of the elements at levels of the total voltage that are significantly below the design value. This difficulty is overcome by grading the voltage sharing circuitry, coupled in parallel with each element, in a prescribed manner, as set out here.

  13. Imaging diagnostics of pulsed plasma discharges in saline generated with various sharp pin powered electrodes

    Science.gov (United States)

    Asimakoulas, L.; Karim, M. L.; Dostal, L.; Krcma, F.; Graham, W. G.; Field, T. A.

    2016-09-01

    Plasmas formed by 1 ms pulses of between 180 and 300 V applied to sharp pin-like electrodes immersed in saline solution have been imaged with a Photron SA-X2 fast framing camera and an Andor iStar 510 ICCD camera. Stainless steel, Tungsten and Gold electrodes were investigated with tip diameters of 30 μm, 1 μm and volume, which appears to move about, but remains close to the tip. In the case of Tungsten with higher voltages or longer pulses the tip of the needle can heat up to incandescent temperatures. At higher voltages shock wave fronts appear to be observed as the vapour layer collapses at the end of the voltage pulse. Backlighting and no lighting to observe bubble/vapour layer formation and emission due to plasma formation were employed. Sometimes at higher voltages a thicker vapour layer engulfs the tip and no plasma emission/current is observed.

  14. Behaviour of total surface charge in SiO{sub 2}-Si system under short-pulsed ultraviolet irradiation cycles characterised by surface photo voltage technique

    Energy Technology Data Exchange (ETDEWEB)

    Kang, Ban-Hong [Material Characterization Department, Shin Etsu Handotai (M) Sdn. Bhd., Ulu Klang, Selangor (Malaysia); Lee, Wah-Pheng [Faculty of Engineering, Multimedia University, Persiaran Multimedia, Cyberjaya, 63100 Selangor (Malaysia); Yow, Ho-Kwang, E-mail: hkyow@mmu.edu.my [Faculty of Engineering, Multimedia University, Persiaran Multimedia, Cyberjaya, 63100 Selangor (Malaysia); Tou, Teck-Yong [Faculty of Engineering, Multimedia University, Persiaran Multimedia, Cyberjaya, 63100 Selangor (Malaysia)

    2009-04-15

    Effects of time-accumulated ultraviolet (UV) irradiation and surface treatment on thermally oxidized p-type silicon wafers were investigated by using the surface photo voltage (SPV) technique via the direct measurement of the total surface charge, Q{sub SC}. The rise and fall times of Q{sub sc} curves, as a function of accumulated UV irradiation, depended on the thermal oxide thickness. A simple model was proposed to explain the time-varying characteristics of Q{sub sc} based on the UV-induced bond breaking of SiOH and SiH, and photoemission of bulk electrons to wafer surface where O{sub 2}{sup -} charges were formed. While these mechanisms resulted in charge variations and hence in Q{sub sc}, these could be removed by rinsing the silicon wafers in de-ionized water followed by spin-dry or blow-dry by an ionizer fan. Empirical parameters were used in the model simulations and curve-fitting of Q{sub SC}. The simulated results suggested that initial changes in the characteristic behaviour of Q{sub sc} were mainly due to the net changes in the positive and negative charges, but subsequently were dominated by the accumulation of O{sub 2}{sup -} during the UV irradiation.

  15. Design of the all solid high-voltage power supply for a gyrotron body

    Energy Technology Data Exchange (ETDEWEB)

    Rao, Yihua [School of Mathematics and Physics, University of South China, Hengyang, 421001 (China); Chen, Wenguang, E-mail: 430000485393@usc.edu.cn [School of Electrical Engineering, University of South China, Hengyang, 421001 (China); Hu, Bo [School of Electrical Engineering, University of South China, Hengyang, 421001 (China); Rao, Jun; Huang, Mei; Kang, Zihua; Feng, Kun [Southwestern Institute of Physics, Chengdu, 610041 (China); Huang, Jiaqi [School of Electrical Engineering, University of South China, Hengyang, 421001 (China)

    2017-04-15

    Highlights: • Completed design of all solid-state high-voltage power supply for gyrotron body on HL-2M ECRH. • Consist of 58 PSM modules and one BUCK module, controlled by DSP system. • Fabricated full voltage 35 kV, 200 mA BPS and tested in dummy load. • The BPS can operate in three modes: single pulse mode, multi-pulse modulation mode and the six-level preset mode. - Abstract: Gyrotron plays an important role in the research of electron cyclotron resonance heating (ECRH) on Tokomak. The high-frequency switched power supply technology and pulse step modulation (PSM) technology are used in the development of the all solid high-voltage body power supply (BPS) for 1 MW/105 GHz Gyrotron on ECRH system. Firstly, the basic structure of the BPS and its control system are introduced. Secondly, the software control algorithm of voltage stabilization and modulate method are developed. Finally, the design is verified by the experiments. The experimental results of the single pulse mode, the multi-pulse modulation mode and the six-level preset mode, are shown. The output voltage of the power supply can reach 35 kV and the current at about 200 mA, which are adjustable in the full range. The maximum modulation frequency can reach 1 kHz and the front edge of the pulse can be adjust from 0 to 3 ms and the accuracy of the output voltage is less than 100 V. The results show that the control method is feasible and can be applied to other high power microwave sources.

  16. High reliability low jitter pulse generator

    Science.gov (United States)

    Savage, Mark E.; Stoltzfus, Brian S.

    2013-01-01

    A method and concomitant apparatus for generating pulses comprising providing a laser light source, disposing a voltage electrode between ground electrodes, generating laser sparks using the laser light source via laser spark gaps between the voltage electrode and the ground electrodes, and outputting pulses via one or more insulated ground connectors connected to the voltage electrode.

  17. Excimer Laser Pulse Compress With Pulse Feedback

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    <正>To attain a shorter laser pulse, a compressing technique called pulse feedback was developed from the saturation gain switch applied to the amplification in a discharge pumping excimer laser cavity. It can

  18. A Repetitive Nanosecond Pulse Source for Generation of Large Volume Streamer Discharge

    Institute of Scientific and Technical Information of China (English)

    TAO Fengbo; ZHANG Qiaogen; GAO Bo; WANG Hu; LI Zhou

    2008-01-01

    Using a unipolar pulse with the rise time and the pulse duration in the order of microsecond as the primary pulse,a nanosecond pulse with the repetitive frequency of several kilohertz is generated by a spark gap switch.By varying both the inter-pulse duration and the pulse frequency,the voltage recovery rate of the spark gap switch is investigated at different working conditions such as the gas pressure,the gas composition as well as the bias voltage.The results reveal that either increase in gas pressure or addition of SF6 to the air can increase the voltage recovery rate.The effect of gas composition on the voltage recovery rate is discussed based on the transferring and distribution of the residual space charges.The repetitive nanosecond pulse source is also applied to the generation of large volume,and the discharge currents are measured to investigate the effect of pulse repetition rate on the large volume streamer discharge.

  19. Application of a pulsed, RF-driven, multicusp source for low energy plasma immersion ion implantation

    Energy Technology Data Exchange (ETDEWEB)

    Wengrow, A.B.; Leung, K.N.; Perkins, L.T.; Pickard, D.S.; Rickard, M.; Williams, M.D. [Lawrence Berkeley Lab., CA (United States); Tucker, M. [Spectrum Sciences, Inc., Santa Clara, CA (United States)

    1996-06-01

    The multicusp ion source can produce large volumes of uniform, quiescent, high density plasmas. A plasma chamber suited for plasma immersion ion implantation (PIII) was readily made. Conventional PIII pulses the bias voltage applied to the substrate which is immersed in a CW mode plasma. Here, a method by which the plasma itself is pulsed was developed. Typically pulse lengths of 500 {mu}s are used and are much shorter than that of the substrate voltage pulse (5-15 ms). This approach, together with low gas pressures and low bias voltages, permits the constant energy implantation of an entire wafer simultaneously without glow discharge. Results show that this process can yield implant currents of up to 2.5 mA/cm{sup 2}; thus very short implant times can be achieved. Uniformity of the ion flux is also discussed. As this method can be scaled to any dimension, it can be made to handle any size wafer.

  20. Investigation of the metabolic consequences of impregnating spinach leaves with trehalose and applying a pulsed electric field.

    Science.gov (United States)

    Dymek, Katarzyna; Panarese, Valentina; Herremans, Els; Cantre, Dennis; Schoo, Rick; Toraño, Javier Sastre; Schluepmann, Henriette; Wadso, Lars; Verboven, Pieter; Nicolai, Bart M; Dejmek, Petr; Gómez Galindo, Federico

    2016-12-01

    The impregnation of leafy vegetables with cryoprotectants using a combination of vacuum impregnation (VI) and pulsed electric fields (PEF) has been proposed by our research group as a method of improving their freezing tolerance and consequently their general quality after thawing. In this study, we have investigated the metabolic consequences of the combination of these unit operations on spinach. The vacuum impregnated spinach leaves showed a drastic decrease in the porosity of the extracellular space. However, at maximum weight gain, randomly located air pockets remained, which may account for oxygen-consuming pathways in the cells being active after VI. The metabolic activity of the impregnated leaves showed a drastic increase that was further enhanced by the application of PEF to the impregnated tissue. Impregnating the leaves with trehalose by VI led to a significant accumulation of trehalose-6-phosphate (T6P), however, this was not further enhanced by PEF. It is suggested that the accumulation of T6P in the leaves may increase metabolic activity, and increase tissue resistance to abiotic stress.

  1. 高压脉冲电场静态处理室的研制%Developing on the Static Chamber of High-Voltage Pulsed Electric Field

    Institute of Scientific and Technical Information of China (English)

    平雪良; 刘翠; 杨瑞金; 赵伟

    2010-01-01

    高压脉冲电场(Pulsed Electric Field, PEF)是一项极具前景的食品非热杀菌技术,其处理关键部件--处理室直接影响杀菌效果.作者设计了电场分布均匀、处理物料容量可调、安全可靠的PEF处理室,应用该PEF处理室对接种大肠杆菌的液蛋进行杀菌,当电场强度为34.2 kV/cm处理时间为400 μs时,原样品菌体浓度为106~107 cfu/mL,大肠杆菌细菌数量降低了约5.05个对数,从而说明作者设计的静态处理室是可行的,可以进行杀菌钝酶等相关机理研究.

  2. Generation of large-scale, barrier-free diffuse plasmas in air at atmospheric pressure using array wire electrodes and nanosecond high-voltage pulses

    Science.gov (United States)

    Teng, Yun; Li, Lee; Liu, Yun-Long; Liu, Lun; Liu, Minghai

    2014-10-01

    This paper introduces a method to generate large-scale diffuse plasmas by using a repetition nanosecond pulse generator and a parallel array wire-electrode configuration. We investigated barrier-free diffuse plasmas produced in the open air in parallel and cross-parallel array line-line electrode configurations. We found that, when the distance between the wire-electrode pair is small, the discharges were almost extinguished. Also, glow-like diffuse plasmas with little discharge weakening were obtained in an appropriate range of line-line distances and with a cathode-grounding cross-electrode configuration. As an example, we produced a large-scale, stable diffuse plasma with volumes as large as 18 × 15 × 15 cm3, and this discharge region can be further expanded. Additionally, using optical and electrical measurements, we showed that the electron temperature was higher than the gas temperature, which was almost the same as room temperature. Also, an array of electrode configuration with more wire electrodes had helped to prevent the transition from diffuse discharge to arc discharge. Comparing the current waveforms of configurations with 1 cell and 9 cells, we found that adding cells significantly increased the conduction current and the electrical energy delivered in the electrode gaps.

  3. Radiatively heated high voltage pyroelectric crystal pulser

    Energy Technology Data Exchange (ETDEWEB)

    Antolak, A.J., E-mail: antolak@sandia.gov [Sandia National Laboratories, Livermore, CA 94550 (United States); Chen, A.X. [Sandia National Laboratories, Livermore, CA 94550 (United States); Leung, K.-N. [Sandia National Laboratories, Livermore, CA 94550 (United States); Nuclear Engineering Department, University of California, Berkeley (United States); Morse, D.H.; Raber, T.N. [Sandia National Laboratories, Livermore, CA 94550 (United States)

    2014-01-21

    Thin lithium tantalate pyroelectric crystals in a multi-stage pulser were heated by quartz lamps during their charging phase to generate high voltage pulses. The charging voltage was determined empirically based on the measured breakdown voltage in air and verified by the induced breakdown voltage of an external high voltage power supply. A four-stage pyroelectric crystal device generated pulse discharges of up to 86 kV using both quartz lamps (radiative) and thermoelectric (conductive) heating. Approximately 50 mJ of electrical energy was harvested from the crystals when radiatively heated in air, and up to 720 mJ was produced when the crystals were submerged in a dielectric fluid. It is anticipated that joule-level pulse discharges could be obtained by employing additional stages and optimizing the heating configuration.

  4. 经皮穿刺手动调压脉冲射频模式治疗颈椎间盘突出症%THE CLINICAL EFFECTS OF PERCUTANEOUS PUNCTURE MANUAL VOLTAGE REGULATION PULSED RADIOFREQUENCY MODE ON CERVICAL DISC HERNIATION

    Institute of Scientific and Technical Information of China (English)

    吴大胜; 刘娜; 宫小文; 宋永光

    2012-01-01

    Objective: To evaluate the clinical effects of percutaneous puncture manual voltage regulation pulsed radiofrequency mode on the treatment cervical disc herniation. Methods: From August 2010 to September 2011, 112 patients with cervical disc herniation were given with percutaneous puncture manual voltage regulation pulsed radiofrequency mode guided through C arm X-ray machine, CT or DSA. The visual analogue scale (VAS) score and clinical effects were recorded before and after treatment. Results: After 3 d the treatment, the excellent cases were 96, the good cases were 14, and the bad cases were 2, the excellent and good rate was 98.2%. There were 2 bad cases because the doctor failed to grasp the good indication. Compared with pre-operation (7.8 ± 0.4), the VAS at 3 d after operation (1.5 ± 0.3) was decreased (P < 0.05). Conclusion: Percutaneous puncture manual voltage regulation pulsed radiofrequency mode therapy is a suitable treatment for cervical disc herniation, with the advantages of simple operation, easy to master, small trauma, not influencing the stability of spine biomechanics, no serious complications.%目的:评估手动调压脉冲射频模式治疗颈椎间盘突出症的临床可行性.方法:2010年8月~2011年9月,112例颈椎间盘突出症患者,在C型臂X线机、CT或DSA引导下接受经皮穿刺手动调压脉冲射频模式治疗.观察并记录术前后的视觉模拟评分(visual analogue scale,VAS),并进行疗效评估.结果:本组112例患者,经过该技术治疗后3d,其中96例治疗效果达优级,14例治疗效果良好,2例效果差,优良率98.2%.其中,效果较差的2例是因为未把握好适应症.与术前VAS评分(7.8±0.4)相比,术后3天VAS评分(1.5±0.3)降低(P<0.05).结论:经皮穿刺手动调压脉冲射频模式治疗颈椎间盘突出症具有操作简单、易于掌握、创伤小、不影响脊柱生物力学稳定性、无严重并发症等特点.是一种可供临床选用的、效果确切又较

  5. 碳纤维复合涂层在高压脉冲电场下的杀菌性能研究%Research on Bactericidal Properties of Carbon Fiber Composite Coatings in High-voltage Pulse Electric Field

    Institute of Scientific and Technical Information of China (English)

    杨鹏鹏; 吴进怡; 柴柯; 林海强; 宋春蕾

    2015-01-01

    ABSTRACT:Objective To explore the inhibition effects and mechanism of high-voltage pulsed electric field ( HPEF) in marine environment on microbial fouling. Methods Carbon fiber / epoxy composite anti-corrosion coating was prepared by brushing meth-od, and the effects of the carbon fiber length and content on the dielectric properties and surface energy of the composite coating as well as the bactericidal performance of the carbon fiber composite coating in high-voltage pulsed electric field. Results The results showed that the carbon fiber length and content were the main factors affecting the dielectric properties of the composite coating un-der high frequency. With the increase of electric field intensity and frequency within the set range, the sterilization rate of the coat-ing obviously increased, while with the increase of duty cycle, the sterilization rate of the coating first increased and then decreased and finally tended to be stable. When the duty cycle was 0. 5, the maximum sterilization rate of 99. 8% was reached. Conclusion The composite coating with a doping content of 0. 1% 5 mm carbon fiber had excellent dielectric properties. High-voltage pulsed e-lectric field had a good killing effect on bacteria and the sterilization rate of the coating could reach 99. 97%.%目的:研究海洋环境下高压脉冲电场对微生物污损的抑制效果和机理。方法采用刷涂法制备碳纤维/环氧防腐涂料复合涂层,研究碳纤维长度和含量对复合涂层的介电性能和表面能的影响以及碳纤维复合涂层在高压脉冲电场作用下的杀菌性能。结果高频电场下,碳纤维长度和含量是影响复合涂层介电性能的主要因素,随着电场强度、频率在设定范围内增加,涂层的杀菌率显著增大;而随占空比的增大,涂层的杀菌率呈先增后减最后趋于平缓的趋势,占空比为0.5时涂层的杀菌率最高达99.8%。结论掺杂0.1%(质量分数)5 mm碳纤维的

  6. Development and application of pulsed electric field instrument with extremely low frequency and high-voltage for biological effects%极低频高压脉冲电场生物学效应仪的设计与应用

    Institute of Scientific and Technical Information of China (English)

    杨运经; 习岗; 张社奇; 刘锴; 张晓辉

    2012-01-01

    In order to carry out the study of biological effects on extremely low frequency high-voltage pulsed electric field, a pulsed electric field generator based on potential fluctuation in plant was designed. The system can produce high-voltage pulse with extremely low frequency, wide pulse width and steep front. The amplitude of voltage is adjustable from 6 to 20 kV and the pulse frequency is adjustable from 0.1 to 15 Hz. Using the pulsed electric field with 100 kV/m, 1 Hz and 80 ms pulse width to treat germinating mung beans and maize seeds,_the results indicated that the shoot length, root length and root number of mung beans and maize were significantly promoted. It was illustrated that the extremely low frequency high-voltage pulsed electric field based on potential fluctuations in plant had a significant biological effects. This paper laid the foundation for further study of biological effect on extremely low-frequency high-voltage pulsed electric field.%为开展极低频高压脉冲电场生物学效应的研究,设计了基于植物本征电位波动的极低频高压脉冲电场生物学效应仪,该系统可以产生幅值高压在6~20 kV、输出频率在0.1~15 Hz范围内数字式可调的极低频、宽脉宽、上升前沿陡的高压脉冲.用100 kV/m、1 Hz、80 ms脉宽的极低频高压脉冲电场处理萌发中的绿豆和玉米种子,发现极低频高压脉冲电场对绿豆和玉米种子的发芽和生长具有较强的促进作用,说明基于植物电位波动的极低频高压脉冲电场具有明显的生物学效应,研究结果可为极低频高压脉冲电场生物学效应的深入研究提供参考.

  7. Assembly delay line pulse generators

    CERN Document Server

    1971-01-01

    Assembly of six of the ten delay line pulse generators that will power the ten kicker magnet modules. One modulator part contains two pulse generators. Capacitors, inductances, and voltage dividers are in the oil tank on the left. Triggered high-pressure spark gap switches are on the platforms on the right. High voltage pulse cables to the kicker magnet emerge under the spark gaps. In the centre background are the assembled master gaps.

  8. Ignition and dynamics of high-voltage glow discharge plasma implantation

    Science.gov (United States)

    Fu, Ricky K. Y.; Chu, Paul K.; Tian, X. B.; Yang, S. Q.

    2006-01-01

    The self-ignition and dynamics of glow discharge plasma in the pulsed high-voltage plasma immersion ion implantation mode have been investigated. After ignition during the pulse-on period, the glow discharge continues to be sustained for a long period of time after the high-voltage pulse has been turned off as monitored by a Langmuir probe. The glow discharge and ignition lie on the left side of the Paschen curve when pd (gas pressure times electrode separation) is adjusted by using different anode to cathode distances utilizing a conducting grounded grid. The increased or constant implantation current Ia reveals that the ion sheath is stable and conforms to the cathode structure as the plasma density increases by one to two orders of magnitude towards the anode. In addition, the duration of the post-pulse-off plasma can be as long as several times of the pulse duration. The ignition time and duration of the plasma depend on the working pressure, applied voltage and pulse duration.

  9. Studying Voltage Transformer Ferroresonance

    Directory of Open Access Journals (Sweden)

    Hamid Radmanesh

    2012-09-01

    Full Text Available This study studies the effect of Circuit Breaker Shunt Resistance (CBSR, Metal Oxide Vaistor (MOV and Neutral earth Resistance (NR on the control of ferroresonance in the voltage transformer. It is expected that NR can controlled ferroresonance better than MOV and CBSR. Study has been done on a one phase voltage transformer rated 100 VA, 275 kV. The simulation results reveal that considering the CBSR and MOV exhibits a great mitigating effect on ferroresonance overvoltages, but these resistances cannot control these phenomena for all range of parameters. By applying NR to the system structure, ferroresonance has been controlled and its amplitude has been damped for all parameters values.

  10. A Single Pulse Sub-Nanosecond Proton RFQ

    Energy Technology Data Exchange (ETDEWEB)

    Hamm, R W; Pearce-Percy, H; Pearson, D; Rougieri, M; Weir, J; Zografos, A; Guethlein, G; Hawkins, S; Falabella, S; Poole, B; Blackfield, D

    2011-03-29

    A Radio Frequency Quadrupole (RFQ) linac system has been developed to provide a single pulse of 2 MeV protons with a beam pulse width of {approx}300 ps and a charge of 30 pC, either for injection into a pulsed Dielectric Wall Accelerator or for bombardment of a target to produce a fast neutron pulse. The 1.2 m long RFQ structure operates at 425 MHz and bunches and accelerates a single 2.35 ns beam pulse injected into it at 35 keV using a parallel plate deflector placed directly in front of the RFQ entrance. The input acceptance properties of the RFQ allow a simple dc bias voltage on the plates to block acceleration of the unwanted beam, with a short rf voltage pulse applied to null the deflection field for the ions within the 8 mm 'kicker' plate length. The use of the RFQ as the accelerating structure allows one to efficiently produce a large charge in a single sub-ns bunch. In addition, the kicker can also be used without the dc bias voltage to produce a 'notch' in the normal RFQ output beam for synchrotron injection.

  11. FY 1998 annual summary report on research and development of hybrid pulse plasma coating (HPPC) system (first year); 1998 nendo hybrid gata pulse plasma coating (HPPC) system no kenkyu kaihatsu seika hokokusho. Daiichinendo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The R and D program was implemented for a hybrid pulse plasma coating system, where organometallic gases as the feed gases were selected, and methods for feeding them and treating the exhaust gases to remove organic metals were studied, as the preliminary steps for the pulse introduction tests. The tests of combining an rf plasma with microwaves and pulse plasma generation have been started. The power source characteristics, e.g., pulse width, voltage and current, were analyzed, and high-voltage pulse voltage application tests were conducted, in order to grasp the power source characteristics related to the pulse voltage application. Generation of high-density plasma has been confirmed by the tests with microwaves absorbed by an rf plasma, and the plasma density measurement has been started using the single probe and double probe methods. It is also confirmed that a pulse voltage can be applied to a high-density plasma. A plasma source type ion injector (PSII) has been made on a trial basis, to collect the data for the injector. (NEDO).

  12. Applied research using a 30 GHz free-electron maser: Experimental study of interacton of high-power pulsed radiation with metals

    Science.gov (United States)

    Baev, V. G.; Vdovin, V. A.; Vikharev, A. A.; Ginzburg, N. S.; Golubev, I. I.; Golubykh, S. M.; Zaitsev, N. I.; Kaminsky, A. K.; Kovalev, Yu. A.; Kozlov, A. P.; Kratko, A. F.; Kryachko, I. A.; Kuzikov, S. V.; Lesnikovich, A. I.; Milevich, I. A.; Perel'shtein, E. A.; Peskov, N. Yu.; Petelin, M. I.; Sedykh, S. N.; Tyutyunnikov, S. I.; Fedotova, Yu. A.

    2012-01-01

    We describe a facility for testing the properties of different objects affected by a sequence of highpower pulses of the microwave electromagnetic field. The facility performance is implemented due to the power level and stability of the single-mode generation of a free electron maser with an output frequency of 30 GHz, which have been achieved at the Joint Institute for Nuclear Research and the Institute of Applied Physics of the Russian Academy of Sciences. This paper describes the experiments on studying of the thermal fatigue of the copper surface in a test cavity, which models the thermal regime of the accelerating structure of the CLIC project (CERN), as well as the experiments on irradiation of biological tissues, metal films, and nanoclusters.

  13. A simple sub-nanosecond ultraviolet light pulse generator with high repetition rate and peak power.

    Science.gov (United States)

    Binh, P H; Trong, V D; Renucci, P; Marie, X

    2013-08-01

    We present a simple ultraviolet sub-nanosecond pulse generator using commercial ultraviolet light-emitting diodes with peak emission wavelengths of 290 nm, 318 nm, 338 nm, and 405 nm. The generator is based on step recovery diode, short-circuited transmission line, and current-shaping circuit. The narrowest pulses achieved have 630 ps full width at half maximum at repetition rate of 80 MHz. Optical pulse power in the range of several hundreds of microwatts depends on the applied bias voltage. The bias voltage dependences of the output optical pulse width and peak power are analysed and discussed. Compared to commercial UV sub-nanosecond generators, the proposed generator can produce much higher pulse repetition rate and peak power.

  14. Comparison of lock-in and pulse-phase thermography for defect characterization in FRP composites applied to concrete

    Science.gov (United States)

    Brown, Jeff; Chittineni, Sai Harsha

    2015-05-01

    Thermal imaging is a well-established technique for the non-destructive evaluation of FRP composites applied to reinforced concrete. Defect characterization using IR thermography, however, remains a topic of on-going research, and there are currently no universally accepted standards for data collection or interpretation. This research involved large scale thermography inspection of two FRP strengthened bridge girders that were removed from service after approximately 10 years of service in a potentially corrosive marine environment. Trial inspections were performed on test areas where defects could be identified using sounding methods. Two procedures showed the most promise for identifying and characterizing defects: sinusoidal (lock-in style) heating with periods ranging from 5 s to 40 s and constant step heating for 30 s followed by 60 s of cooling. Both methods resulted in a series of phase images that provided insight into the depth and general nature of detected defects. This paper presents the findings of a comparison study between these two thermal imaging techniques.

  15. Over-voltage protection system and method

    Energy Technology Data Exchange (ETDEWEB)

    Chi, Song; Dong, Dong; Lai, Rixin

    2017-05-02

    An over-voltage protection system includes an electronic valve connected across two terminals of a circuit and an over-voltage detection circuit connected across one of the plurality of semiconductor devices for detecting an over-voltage across the circuit. The electronic valve includes a plurality of semiconductor devices connected in series. The over-voltage detection circuit includes a voltage divider circuit connected to a break-over diode in a way to provide a representative low voltage to the break-over diode and an optocoupler configured to receive a current from the break-over diode when the representative low voltage exceeds a threshold voltage of the break-over diode indicating an over-voltage condition. The representative low voltage provided to the break-over diode represents a voltage across the one semiconductor device. A plurality of self-powered gate drive circuits are connected to the plurality of semiconductor devices, wherein the plurality of self-powered gate drive circuits receive over-voltage triggering pulses from the optocoupler during the over-voltage condition and switch on the plurality of semiconductor devices to bypass the circuit.

  16. 基于PSM技术的70kV/90A高压脉冲电源的研制%Development of the 70kV/90A High-Voltage Pulse Power Supply Based on PSM Technology

    Institute of Scientific and Technical Information of China (English)

    徐伟东; 陈文光; 宣伟民; 姚列英; 王英翘

    2011-01-01

    The high microwave and neutral beam injection of the auxiliary heating systems are used to heat or drive the plasma in the controlled nuclear fusion devices. These equipment can be destroyed easily with low energy when arcing occurs. So the high-voltage power supply which supplies to the auxiliary heating systems should have many features, such as flexible control, high stability, fast response, high power factor, short protective time, very low energy discharged to these equipment when the loads are arcing. The power supply based on PSM technology is a method of controlling the total output voltage of many identical DC choppers connected in series by means of managing the work of them step by step and modulating their pulse widths in a certain sequence. This kind of power supply has some advantages which have been mentioned, especially the low energy stored in the whole system and short protective time. Such a high voltage power supply system has already been developed. Its circuit is simple and control mode is flexible. The results show that the output is about 72kV/90A and the parameters are superior to the high-voltage power supply based on thyristors.%在受控核聚变实验中,辅助加热系统采用高功率微波和高能粒子对等离子体进行加热或驱动。这些部件不仅要求为其供电的高压电源稳定度高,而且要求在它们发生打火现象时,保护时间短(〈10gs),高压电源对其释放的能量小,否则这些关键部件极易受到损坏。基于脉冲步进调制PSM技术的高压脉冲电源是许多相同的脉冲电源串联并经过特定的调制方式控制,从而实现高压大功率输出。该高压电源有控制方式灵活、输出功率高、功率因数高、稳定度高、响应速度快、保护时间短、故障时系统对负载的释能小等众多优点。尤其保护时该电源系统储能小,时间短,满足各种高功率微波管和加速器的要求。本文分析了基于

  17. Solid-state pulse forming module with adjustable pulse duration

    Science.gov (United States)

    Wang, Langning; Liu, Jinliang; Qiu, Yongfeng; Chu, Xu; Zhang, Qingmeng

    2017-03-01

    A new solid-state pulse forming module is described in this paper. The pulse forming module is fabricated on a glass ceramic substrate, with the dimension of 250 mm × 95 mm × 4 mm. By changing the copper strips used in the pulse forming modules, the pulse duration of the obtained pulsed can range from 80 ns to 140 ns. Both the simulation and tests show that the pulse forming module has a good pulse forming ability. Under a high voltage in microsecond's time, the new pulse forming modules can hold off a voltage up to 25 kV higher than that of the previous study. In addition, future optimization for the field enhancement near the thin electrode edge has been proposed and simulated.

  18. Improved direct power control of a grid-connected voltage source converter during network unbalance

    Institute of Scientific and Technical Information of China (English)

    Peng ZHOU; Wei ZHANG; Yi-kang HE; Rong ZENG

    2010-01-01

    This paper deals with an improved direct power control(DPC)strategy for the pulse width modulation(PWM)voltage source converter(VSC)under unbalanced grid voltage conditions.In order to provide enhanced control performance for the VSC,the resonant controllers tuned at the double grid frequency are applied in the DPC design to eliminate the power pulsations and dc link voltage ripples produced by the transient unbalanced grid faults.In this way,the output power and dc link voltage of the VSC can be directly regulated without positive and negative sequential decomposition.As a result,and as has been verified by experiment,the proposed method can provide fast dynamic response with easy implementation.

  19. Dynamic magnetization switching and spin wave excitations by voltage-induced torque

    Science.gov (United States)

    Shiota, Yoichi

    2013-03-01

    The effect of electric fields on ultrathin ferromagnetic metal layer is one of the promising approaches for manipulating the spin direction with low-energy consumption, localization, and coherent behavior. Several experimental approaches to realize it have been investigated using ferromagnetic semiconductors, magnetostriction together with piezo-electric materials, multiferroic materials, and ultrathin ferromagnetic layer. In this talk, we will present a dynamic control of spins by voltage-induced torque. We used the magnetic tunnel junctions with ultrathin ferromagnetic layer, which shows voltage-induced perpendicular magnetic anisotropy change. By applying the voltage to the junction, the magnetic easy-axis in the ultrathin ferromagnetic layer changes from in-plane to out-of-plane, which causes a precession of the spins. This precession resulted in a two-way toggle switching by determining an appropriate pulse length. On the other hand, an application of rf-voltage causes an excitation of a uniform spin-wave. Since the precession of spin associates with an oscillation in the resistance of the junction, the applied rf-signal is rectified and produces a dc-voltage. From the spectrum of the dc-voltage as a function of frequency, we could estimate the voltage-induced torque. This research was supported by CREST-JST, G-COE program, and JSPS for the fellowship. Collaborators include T. Nozaki, S. Miwa, F. Bonell, N. Mizuochi, T. Shinjo, and Y. Suzuki.

  20. Analytical Expressions of Induced Coil Voltages Generated by Pulsed Eddy Currents for Metal Pipe Testing%金属管道外侧脉冲磁场激励的线圈电压解析式

    Institute of Scientific and Technical Information of China (English)

    陈兴乐; 雷银照

    2012-01-01

    This paper solved the eddy current field induced by pulse current in saddle-shaped coil outside the metal pipe with linear conductivity and permeability.By using the second order vector potential,the magnetic field in the air could be described by a single scalar function,and the calculation process could thus be simplified.We presented the boundary value problems of this electromagnetic model and obtained the linear equations for unknown coefficients.Then,we reduced the condition number of the coefficient matrix through substitution of variables and solved the linear equations by using block matrix.Based on the Fourier Transform,we obtained the analytical solution of the coil voltage induced by arbitrary waveform current in the multi-turn saddle-shaped drive coil.The analytical expressions were verified through a comparison of the theoretical curves with the experimental curves of the austenite stainless steel pipes.Results in this paper provide theoretical basis for simulation calculation and experimental study of the pulsed eddy current testing for pipes.%求解了线性导电、导磁中空管道外鞍形线圈通有脉冲电流时的涡流场。引入二阶矢量位,用一个标量函数来描述空气场域中的磁场,简化了求解过程。给出了模型的电磁场边值问题,得出了待定系数线性方程组,通过变量代换,降低了系数矩阵的条件数,并用分块矩阵的方法求解了此方程组。利用傅里叶变换,得到了多匝鞍形激励线圈中通有任意波形电流时检测线圈两端感应电压的解析式。通过与奥氏体不锈钢管的实验曲线对比,验证了所得解析式的正确性。所得结果可为管道脉冲涡流检测的仿真计算与实验研究提供参考。

  1. Computer Controlled High Precise,High Voltage Pules Generator

    Institute of Scientific and Technical Information of China (English)

    但果; 邹积岩; 丛吉远; 董恩源

    2003-01-01

    High precise, high voltage pulse generator made up of high-power IGBT and pulse transformers controlled by a computer are described. A simple main circuit topology employed in this pulse generator can reduce the cost meanwhile it still meets special requirements for pulsed electric fields (PEFs) in food process. The pulse generator utilizes a complex programmable logic device (CPLD) to generate trigger signals. Pulse-frequency, pulse-width and pulse-number are controlled via RS232 bus by a computer. The high voltage pulse generator well suits to the application for fluid food non-thermal effect in pulsed electric fields, for it can increase and decrease by the step length 1.

  2. Coiled transmission line pulse generators

    Energy Technology Data Exchange (ETDEWEB)

    McDonald, Kenneth Fox (Columbia, MO)

    2010-11-09

    Methods and apparatus are provided for fabricating and constructing solid dielectric "Coiled Transmission Line" pulse generators in radial or axial coiled geometries. The pour and cure fabrication process enables a wide variety of geometries and form factors. The volume between the conductors is filled with liquid blends of monomers, polymers, oligomers, and/or cross-linkers and dielectric powders; and then cured to form high field strength and high dielectric constant solid dielectric transmission lines that intrinsically produce ideal rectangular high voltage pulses when charged and switched into matched impedance loads. Voltage levels may be increased by Marx and/or Blumlein principles incorporating spark gap or, preferentially, solid state switches (such as optically triggered thyristors) which produce reliable, high repetition rate operation. Moreover, these Marxed pulse generators can be DC charged and do not require additional pulse forming circuitry, pulse forming lines, transformers, or an a high voltage spark gap output switch. The apparatus accommodates a wide range of voltages, impedances, pulse durations, pulse repetition rates, and duty cycles. The resulting mobile or flight platform friendly cylindrical geometric configuration is much more compact, light-weight, and robust than conventional linear geometries, or pulse generators constructed from conventional components. Installing additional circuitry may accommodate optional pulse shape improvements. The Coiled Transmission Lines can also be connected in parallel to decrease the impedance, or in series to increase the pulse length.

  3. Small-signal, continuous, exact model of PWM voltage regulators

    Science.gov (United States)

    Burkhardt, W.; Maranesi, P.; Varoli, V.

    1985-02-01

    The small-signal time-continuous open-loop response of buck, boost, and buck-boost pulse-width-modulation (PWM) voltage regulators using MOSFET switches in their power stages is modeled, applying a time-domain sampling theorem (Woodward, 1953) to obtain the Fourier open-loop transfer function corresponding to the comb function describing the response at the chopping instants only. The results are presented graphically along with simplified circuit diagrams of the PWM devices, and the accuracy and computational efficiency of the analytical approach are indicated.

  4. Accurate Switched-Voltage voltage averaging circuit

    OpenAIRE

    金光, 一幸; 松本, 寛樹

    2006-01-01

    Abstract ###This paper proposes an accurate Switched-Voltage (SV) voltage averaging circuit. It is presented ###to compensated for NMOS missmatch error at MOS differential type voltage averaging circuit. ###The proposed circuit consists of a voltage averaging and a SV sample/hold (S/H) circuit. It can ###operate using nonoverlapping three phase clocks. Performance of this circuit is verified by PSpice ###simulations.

  5. Pulse on Pulse

    DEFF Research Database (Denmark)

    Schmidt, Ulrik; Carlson, Merete

    2012-01-01

    Pulse on Pulse” investigates the relation between signifying processes and non-signifying material dynamism in the installation Pulse Room (2006-) by Mexican Canadian artist Rafael Lozano-Hemmer. In Pulse Room the sense of pulse is ambiguous. Biorhythms are transmitted from the pulsing energy...... and pulsating ‘room’. Hence, the visitors in Pulse Room are invited into a complex scenario that continuously oscillates between various aspects of signification (the light bulbs representing individual lives; the pulse itself as the symbolic ‘rhythm of life’) and instants of pure material processuality...... a multilayered sense of time and space that is central to the sensory experience of Pulse Room as a whole. Pulse Room is, at the very same time, an anthropomorfized archive of a past intimacy and an all-encompassing immersive environment modulating continuously in real space-time....

  6. FPGA implementation of high-frequency multiple PWM for variable voltage variable frequency controller

    Energy Technology Data Exchange (ETDEWEB)

    Boumaaraf, Abdelâali, E-mail: aboumaaraf@yahoo.fr [Université Abbès Laghrour, Laboratoire des capteurs, Instrumentations et procédés (LCIP), Khenchela (Algeria); University of Farhat Abbas Setif1, Sétif, 19000 (Algeria); Mohamadi, Tayeb [University of Farhat Abbas Setif1, Sétif, 19000 (Algeria); Gourmat, Laïd [Université Abbès Laghrour, Khenchela, 40000 (Algeria)

    2016-07-25

    In this paper, we present the FPGA implementation of the multiple pulse width modulation (MPWM) signal generation with repetition of data segments, applied to the variable frequency variable voltage systems and specially at to the photovoltaic water pumping system, in order to generate a signal command very easily between 10 Hz to 60 Hz with a small frequency and reduce the cost of the control system.

  7. Optical visualization and electrical characterization of fast-rising pulsed dielectric barrier discharge for airflow control applications

    Science.gov (United States)

    Benard, Nicolas; Zouzou, Nourredine; Claverie, Alain; Sotton, Julien; Moreau, Eric

    2012-02-01

    Flow control consists of manipulating flows in an effective and robust manner to improve the global performances of transport systems or industrial processes. Plasma technologies, and particularly surface dielectric barrier discharge (DBD), can be a good candidate for such purpose. The present experimental study focuses on optical and electrical characterization of plasma sheet formed by applying a pulse of voltage with rising and falling periods of 50 ns for a typical surface DBD geometry. Positive and negative polarities are compared in terms of current behavior, deposited energy, fast-imaging of the plasma propagation, and resulting modifications of the surrounding medium by using shadowgraphy acquisitions. Positive and negative pulses of voltage produce streamers and corona type plasma, respectively. Both of them result in the production of a localized pressure wave propagating in the air with a speed maintained at 343 m/s (measurements at room temperature of 20 °C). This suggests that the produced pressure wave can be considered as a propagating sound wave. The intensity of the pressure wave is directly connected to the dissipated energy at the dielectric wall with a linear increase with the applied voltage amplitude and a strong dependence toward the rising time. At constant voltage amplitude, the pressure wave is reinforced by using a positive pulse. The present investigation also reveals that rising and decaying periods of a single pulse of voltage result in two distinct pressure waves. As a result, superposition or successive pressure wave can be produced by adjusting the width of the pulse.

  8. Pulsed-coil magnet systems for applying uniform 10-30 T fields to centimeter-scale targets on Sandia's Z facility

    Science.gov (United States)

    Rovang, D. C.; Lamppa, D. C.; Cuneo, M. E.; Owen, A. C.; McKenney, J.; Johnson, D. W.; Radovich, S.; Kaye, R. J.; McBride, R. D.; Alexander, C. S.; Awe, T. J.; Slutz, S. A.; Sefkow, A. B.; Haill, T. A.; Jones, P. A.; Argo, J. W.; Dalton, D. G.; Robertson, G. K.; Waisman, E. M.; Sinars, D. B.; Meissner, J.; Milhous, M.; Nguyen, D. N.; Mielke, C. H.

    2014-12-01

    Sandia has successfully integrated the capability to apply uniform, high magnetic fields (10-30 T) to high energy density experiments on the Z facility. This system uses an 8-mF, 15-kV capacitor bank to drive large-bore (5 cm diameter), high-inductance (1-3 mH) multi-turn, multi-layer electromagnets that slowly magnetize the conductive targets used on Z over several milliseconds (time to peak field of 2-7 ms). This system was commissioned in February 2013 and has been used successfully to magnetize more than 30 experiments up to 10 T that have produced exciting and surprising physics results. These experiments used split-magnet topologies to maintain diagnostic lines of sight to the target. We describe the design, integration, and operation of the pulsed coil system into the challenging and harsh environment of the Z Machine. We also describe our plans and designs for achieving fields up to 20 T with a reduced-gap split-magnet configuration, and up to 30 T with a solid magnet configuration in pursuit of the Magnetized Liner Inertial Fusion concept.

  9. A model for mark size dependence on field emission voltage in heat-assisted magnetic probe recording on CoNi/Pt multilayers

    NARCIS (Netherlands)

    Zhang, Li; Bain, James A.; Zhu, Jian-Gang; Abelmann, Leon; Onoue, Takahiro

    2004-01-01

    A method of heat-assisted magnetic recording (HAMR) potentially suitable for probe-based storage systems is characterized. In this work, field emission current from a scanning tunneling microscope (STM) tip is used as the heating source. Pulse voltages of 2-7 V with a duration of 500 ns were applied

  10. Capacitor voltage balance performance comparison of MMC-STATCOM using NLC and PS-PWM strategies during negative sequence current injection

    DEFF Research Database (Denmark)

    Pereira, Heverton A.; F. Cupertino, Allan; S. Xavier, Lucus

    2016-01-01

    This paper addresses the modular multilevel converter applied as a static synchronous compensator. The main objective of this work is to compare the converter performance considering two different submodule capacitor voltage balancing strategies: nearest level control and phase-shifted pulse width...

  11. Neural networks applied to inverters control; Les reseaux de neurones appliques a la commande des convertisseurs

    Energy Technology Data Exchange (ETDEWEB)

    Jammes, B.; Marpinard, J.C.

    1995-12-31

    Neural networks are scarcely applied to power electronics. This attempt includes two different topics: optimal control and computerized simulation. The learning has been performed through output error feedback. For implementation, a buck converter has been used as a voltage pulse generator. (D.L.) 7 refs.

  12. Nanosecond repetitively pulsed discharges in air at atmospheric pressure—the spark regime

    Science.gov (United States)

    Pai, David Z.; Lacoste, Deanna A.; Laux, Christophe O.

    2010-12-01

    Nanosecond repetitively pulsed (NRP) spark discharges have been studied in atmospheric pressure air preheated to 1000 K. Measurements of spark initiation and stability, plasma dynamics, gas temperature and current-voltage characteristics of the spark regime are presented. Using 10 ns pulses applied repetitively at 30 kHz, we find that 2-400 pulses are required to initiate the spark, depending on the applied voltage. Furthermore, about 30-50 pulses are required for the spark discharge to reach steady state, following initiation. Based on space- and time-resolved optical emission spectroscopy, the spark discharge in steady state is found to ignite homogeneously in the discharge gap, without evidence of an initial streamer. Using measured emission from the N2 (C-B) 0-0 band, it is found that the gas temperature rises by several thousand Kelvin in the span of about 30 ns following the application of the high-voltage pulse. Current-voltage measurements show that up to 20-40 A of conduction current is generated, which corresponds to an electron number density of up to 1015 cm-3 towards the end of the high-voltage pulse. The discharge dynamics, gas temperature and electron number density are consistent with a streamer-less spark that develops homogeneously through avalanche ionization in volume. This occurs because the pre-ionization electron number density of about 1011 cm-3 produced by the high frequency train of pulses is above the critical density for streamer-less discharge development, which is shown to be about 108 cm-3.

  13. Electrical pulse fabrication of graphene nanopores in electrolyte solution

    Energy Technology Data Exchange (ETDEWEB)

    Kuan, Aaron T.; Szalay, Tamas [School of Engineering and Applied Sciences, Harvard University, Cambridge, Massachusetts 02138 (United States); Lu, Bo [Department of Physics, Harvard University, Cambridge, Massachusetts 02138 (United States); Xie, Ping [Oxford Nanopore Technologies, One Kendall Square, Cambridge, Massachusetts 02139 (United States); Golovchenko, Jene A., E-mail: golovchenko@physics.harvard.edu [School of Engineering and Applied Sciences, Harvard University, Cambridge, Massachusetts 02138 (United States); Department of Physics, Harvard University, Cambridge, Massachusetts 02138 (United States)

    2015-05-18

    Nanopores in graphene membranes can potentially offer unprecedented spatial resolution for single molecule sensing, but their fabrication has thus far been difficult, poorly scalable, and prone to contamination. We demonstrate an in-situ fabrication method that nucleates and controllably enlarges nanopores in electrolyte solution by applying ultra-short, high-voltage pulses across the graphene membrane. This method can be used to rapidly produce graphene nanopores with subnanometer size accuracy in an apparatus free of nanoscale beams or tips.

  14. Simulation Investigation of SPWM, THIPWM and SVPWM Techniques for Three Phase Voltage Source Inverter

    Directory of Open Access Journals (Sweden)

    Zulkifilie Bin Ibrahim

    2014-03-01

    Full Text Available Pulse width modulation (PWM technique is one of the vital issues for power electronic circuit control. A number of Pulse width modulation (PWM techniques are increasingly applied in many new industrial applications that require superior performance. The most widely applied PWM technique for three-phase voltage source inverters are Sine Pulse Width Modulation (SPWM, Third Harmonic Injection Pulse Width Modulation (THIPWM and Space Vector Pulse Width Modulation (SVPWM. SPWM is the most simple modulation technique that can realize easily in analog circuit. However, it has some drawbacks such as higher total harmonic distortion (THD, lower switching frequency and not capable in over modulation region. THIPWM and SVPWM both provide better THD compared to SPWM. SVPWM shows lower THD in over modulation region and in high frequency application compared to THIPWM. These three techniques are discussed, analyzed and compared in terms of modulation index, switching frequency and inverter input voltage in this paper. The modeling and simulation for all PWM techniques have been done by using MATLAB/SIMULINK and Origin 6.1. From the simulation results, SVPWM shows the best performance and meet IEEE 519 standard of current harmonics level.

  15. Intense Pulsed Heavy Ion Beam Technology

    Science.gov (United States)

    Masugata, Katsumi; Ito, Hiroaki

    Development of intense pulsed heavy ion beam accelerator technology is described for the application of materials processing. Gas puff plasma gun and vacuum arc discharge plasma gun were developed as an active ion source for magnetically insulated pulsed ion diode. Source plasma of nitrogen and aluminum were successfully produced with the gas puff plasma gun and the vacuum arc plasma gun, respectively. The ion diode was successfully operated with gas puff plasma gun at diode voltage 190 kV, diode current 2.2 kA and nitrogen ion beam of ion current density 27 A/cm2 was obtained. The ion composition was evaluated by a Thomson parabola spectrometer and the purity of the nitrogen ion beam was estimated to be 86%. The diode also operated with aluminum ion source of vacuum arc plasma gun. The ion diode was operated at 200 kV, 12 kA, and aluminum ion beam of current density 230 A/cm2 was obtained. The beam consists of aluminum ions (Al(1-3)+) of energy 60-400 keV, and protons (90-130 keV), and the purity was estimated to be 89 %. The development of the bipolar pulse accelerator (BPA) was reported. A double coaxial type bipolar pulse generator was developed as the power supply of the BPA. The generator was tested with dummy load of 7.5 ohm, bipolar pulses of -138 kV, 72 ns (1st pulse) and +130 kV, 70 ns (2nd pulse) were succesively generated. By applying the bipolar pulse to the drift tube of the BPA, nitrogen ion beam of 2 A/cm2 was observed in the cathode, which suggests the bipolar pulse acceleration.

  16. Integrated Reconfigurable High-Voltage Transmitting Circuit for CMUTs

    DEFF Research Database (Denmark)

    Llimos Muntal, Pere; Larsen, Dennis Øland; Jørgensen, Ivan Harald Holger

    2014-01-01

    -out and measurements are performed on the integrated circuit. The transmitting circuit is reconfigurable externally making it able to drive a wide variety of CMUTs. The transmitting circuit can generate several pulse shapes, pulse voltages up to 100 V, maximum pulse range of 50 V and frequencies up to 5 MHz. The area...

  17. Efficiency of pulse-mode dielectric barrier discharge excimer lamp in constant duty cycle

    Science.gov (United States)

    Akashi, Haruaki; Oda, Akinori; Sakai, Yosuke

    2008-10-01

    Efficiency of pulse-mode dielectric barrier discharge (DBD) excimer lamp under constant duty cycle with increasing applied voltage has been simulated using two dimensional fluid model[1]. Xe gas with 300Torr pressure is assumed. And the simulated region considered in this model is 1cm(gap length)x3cm(radial length). Periodical boundary conditions are assumed for the radial direction boundaries. The both electrodes are covered with dielectrics and their thickness is 0.2cm. 5˜8kV trapezoid shape voltage is applied with the same voltage rising ratio and 50% duty ratio waveform with 200x10^3pps repetition rate. The discharge occurs at the rising edge and tailing edge of applied voltage. 172nm VUV intensity obtained from first discharge is higher than second one in lower applied voltage (<6kV) case. And in higher voltage case, the intensity from second discharge becomes higher. This is explained by shortening of interval time between the discharges. The short interval time makes higher initial electron density for second discharge. As a results, the input and 172nm VUV output power increases with increasing applied voltage, but the efficiency decreases. Because of inefficient surface discharge [1]H. Akashi et al, IEEE Trans. Plasma Science, Vol.33,No.2(2005,4)pp.308-309

  18. LONGITUDINAL DISCH. CO2 LASER WITH PULSED PRE-IONIZATION

    Institute of Scientific and Technical Information of China (English)

    Yu Yanning; Wan Chongyi

    2002-01-01

    A novel pre-ionization scheme of helical transverse-pulsed pre-ionization in a longitudinal discharge CO2 laser is presented. The laser tube is made of glass with inner diameter of 7.5mm and discharge length of 50cm. The laser performance characteristics as functions of parameters, such as pressure, charging capacitance and applied voltage, are investigated. Compared with the same laser structure without pre-ionization, the maximum pulse energy improves by 23%, the optimum electro-optical efficiency increases by 31%, and the specific output energy reaches 26 J/(L·atm).

  19. Apparatus and Method for Compensating for Process, Voltage, and Temperature Variation of the Time Delay of a Digital Delay Line

    Science.gov (United States)

    Seefeldt, James (Inventor); Feng, Xiaoxin (Inventor); Roper, Weston (Inventor)

    2013-01-01

    A process, voltage, and temperature (PVT) compensation circuit and a method of continuously generating a delay measure are provided. The compensation circuit includes two delay lines, each delay line providing a delay output. The two delay lines may each include a number of delay elements, which in turn may include one or more current-starved inverters. The number of delay lines may differ between the two delay lines. The delay outputs are provided to a combining circuit that determines an offset pulse based on the two delay outputs and then averages the voltage of the offset pulse to determine a delay measure. The delay measure may be one or more currents or voltages indicating an amount of PVT compensation to apply to input or output signals of an application circuit, such as a memory-bus driver, dynamic random access memory (DRAM), a synchronous DRAM, a processor or other clocked circuit.

  20. Current-voltage characteristics of Bi{sub 2}Sr{sub 2}Ca{sub 2}Cu{sub 3}O{sub 10+x}/Ag multifilamentary tapes in zero applied magnetic field

    Energy Technology Data Exchange (ETDEWEB)

    Crisan, A. [Institute of Cryogenics, University of Southampton, Southampton (United Kingdom); Institute of Physics and Technology of Materials, Bucharest (Romania); Miu, L.; Popa, S. [Institute of Physics and Technology of Materials, Bucharest (Romania); Yang, Y.; Beduz, C. [Institute of Cryogenics, University of Southampton, Southampton (United Kingdom)

    1997-05-01

    Current-voltage characteristics of multifilamentary Bi{sub 2}Sr{sub 2}Ca{sub 2}Cu{sub 3}O{sub 10+x}/Ag tapes (short samples) produced by the 'powder in tube' technique were measured at different temperatures close to the mean-field critical temperature, and inzero applied magnetic field. After performing the required corrections due to the current flowing in the silver matrix, the I-V curves were interpreted in terms of current-induced unbinding of the thermally created vortex-antivortex pairs. Two possible mechanisms for appearance of a finite critical current in zero applied magnetic field are discussed: the Jensen-Minnhagen quasi-two-dimensional (2D) approach, that takes into account the interlayer Josephson coupling, and a model of size limitation of vortex fluctuations. From our analysis, it seems that the latter model is more suitable for this kind of superconducting material, due probably to an accentuated intrinsic anisotropy. (author)

  1. Atmospheric pressure microplasmas in ZnO nanoforests under high voltage stress

    Directory of Open Access Journals (Sweden)

    Nafisa Noor

    2015-09-01

    Full Text Available Atmospheric pressure ZnO microplasmas have been generated by high amplitude single pulses and DC voltages applied using micrometer-separated probes on ZnO nanoforests. The high voltage stress triggers plasma breakdown and breakdown in the surrounding air followed by sublimation of ZnO resulting in strong blue and white light emission with sharp spectral lines and non-linear current-voltage characteristics. The nanoforests are made of ZnO nanorods (NRs grown on fluorine doped tin oxide (FTO glass, poly-crystalline silicon and bulk p-type silicon substrates. The characteristics of the microplasmas depend strongly on the substrate and voltage parameters. Plasmas can be obtained with pulse durations as short as ∼1 μs for FTO glass substrate and ∼100 ms for the silicon substrates. Besides enabling plasma generation with shorter pulses, NRs on FTO glass substrate also lead to better tunability of the operating gas temperature. Hot and cold ZnO microplasmas have been observed with these NRs on FTO glass substrate. Sputtering of nanomaterials during plasma generation in the regions surrounding the test area has also been noticed and result in interesting ZnO nanostructures (‘nano-flowers’ and ‘nano-cauliflowers’. A practical way of generating atmospheric pressure ZnO microplasmas may lead to various lighting, biomedical and material processing applications.

  2. Analog implementation of pulse-coupled neural networks.

    Science.gov (United States)

    Ota, Y; Wilamowski, B M

    1999-01-01

    This paper presents a compact architecture for analog CMOS hardware implementation of voltage-mode pulse-coupled neural networks (PCNN's). The hardware implementation methods shows inherent fault tolerance specialties and high speed, which is usually more than an order of magnitude over the software counterpart. A computational style described in this article mimics a biological neural network using pulse-stream signaling and analog summation and multiplication. Pulse-stream encoding technique uses pulse streams to carry information and control analog circuitry, while storing further analog information on the time axis. The main feature of the proposed neuron circuit is that the structure is compact, yet exhibiting all the basic properties of natural biological neurons. Functional and structural forms of neural and synaptic functions are presented along with simulation results. Finally, the proposed design is applied to image processing to demonstrate successful restoration of images and their features.

  3. Radar Range Sidelobe Reduction Using Adaptive Pulse Compression Technique

    Science.gov (United States)

    Li, Lihua; Coon, Michael; McLinden, Matthew

    2013-01-01

    Pulse compression has been widely used in radars so that low-power, long RF pulses can be transmitted, rather than a highpower short pulse. Pulse compression radars offer a number of advantages over high-power short pulsed radars, such as no need of high-power RF circuitry, no need of high-voltage electronics, compact size and light weight, better range resolution, and better reliability. However, range sidelobe associated with pulse compression has prevented the use of this technique on spaceborne radars since surface returns detected by range sidelobes may mask the returns from a nearby weak cloud or precipitation particles. Research on adaptive pulse compression was carried out utilizing a field-programmable gate array (FPGA) waveform generation board and a radar transceiver simulator. The results have shown significant improvements in pulse compression sidelobe performance. Microwave and millimeter-wave radars present many technological challenges for Earth and planetary science applications. The traditional tube-based radars use high-voltage power supply/modulators and high-power RF transmitters; therefore, these radars usually have large size, heavy weight, and reliability issues for space and airborne platforms. Pulse compression technology has provided a path toward meeting many of these radar challenges. Recent advances in digital waveform generation, digital receivers, and solid-state power amplifiers have opened a new era for applying pulse compression to the development of compact and high-performance airborne and spaceborne remote sensing radars. The primary objective of this innovative effort is to develop and test a new pulse compression technique to achieve ultrarange sidelobes so that this technique can be applied to spaceborne, airborne, and ground-based remote sensing radars to meet future science requirements. By using digital waveform generation, digital receiver, and solid-state power amplifier technologies, this improved pulse compression

  4. Pulse on Pulse

    DEFF Research Database (Denmark)

    Schmidt, Ulrik; Carlson, Merete

    2012-01-01

    and pulsating ‘room’. Hence, the visitors in Pulse Room are invited into a complex scenario that continuously oscillates between various aspects of signification (the light bulbs representing individual lives; the pulse itself as the symbolic ‘rhythm of life’) and instants of pure material processuality......“Pulse on Pulse” investigates the relation between signifying processes and non-signifying material dynamism in the installation Pulse Room (2006-) by Mexican Canadian artist Rafael Lozano-Hemmer. In Pulse Room the sense of pulse is ambiguous. Biorhythms are transmitted from the pulsing energy...... of the visitor’s beating heart to the blink of a fragile light bulb, thereby transforming each light bulb into a register of individual life. But at the same time the blinking light bulbs together produce a chaotically flickering light environment composed by various layers of repetitive rhythms, a vibrant...

  5. Transitions between corona, glow, and spark regimes of nanosecond repetitively pulsed discharges in air at atmospheric pressure

    OpenAIRE

    Pai, David,; Lacoste, Deanna,; Laux, C.

    2010-01-01

    International audience; In atmospheric pressure air preheated from 300 to 1000 K, the nanosecond repetitively pulsed (NRP) method has been used to generate corona, glow, and spark discharges. Experiments have been performed to determine the parameter space (applied voltage, pulse repetition frequency, ambient gas temperature, and interelectrode gap distance) of each discharge regime. In particular, the experimental conditions necessary for the glow regime of NRP discharges have been determine...

  6. Photonic generation of ultrawideband monocycle and doublet pulses by using a semiconductor-optical-amplifier-based wavelength converter

    DEFF Research Database (Denmark)

    Zhou, Enbo; Yu, Xianbin; Zhang, Xinliang;

    2009-01-01

    Photonic generation of ultrawideband (UWB) monocycle and doublet pulses is experimentally demonstrated using a cascaded electroabsorption modulator (EAM) and semiconductor optical amplifier by exploiting a combination of cross-absorption modulation and cross-gain modulation. The polarities...... and shapes of UWB monocycle and doublet pulses can be simply controlled using an optical time-delay controller and the reverse voltage applied to the EAM. The corresponding measured rf spectra meet the UWB criteria....

  7. An all-solid-state microsecond-range quasi-square pulse generator based on fractional-turn ratio saturable pulse transformer and anti-resonance network

    Science.gov (United States)

    Chen, Rong; Yang, Jianhua; Cheng, Xinbing; Pan, Zilong

    2017-03-01

    High voltage pulse generators are widely applied in a number of fields. Defense and industrial applications stimulated intense interests in the area of pulsed power technology towards the system with high power, high repetition rate, solid state characteristics, and compact structure. An all-solid-state microsecond-range quasi-square pulse generator based on a fractional-turn ratio saturable pulse transformer and anti-resonance network is proposed in this paper. This generator consists of a charging system, a step-up system, and a modulating system. In this generator, the fractional-turn ratio saturable pulse transformer is the key component since it acts as a step-up transformer and a main switch during the working process. Demonstrative experiments show that if the primary storage capacitors are charged to 400 V, a quasi-square pulse with amplitude of about 29 kV can be achieved on a 3500 Ω resistive load, as well as the pulse duration (full width at half maximum) of about 1.3 μs. Preliminary repetition rate experiments are also carried out, which indicate that this pulse generator could work stably with the repetition rates of 30 Hz and 50 Hz. It can be concluded that this kind of all-solid-state microsecond-range quasi-square pulse generator can not only lower both the operating voltage of the primary windings and the saturable inductance of the secondary windings, thus ideally realizing the magnetic switch function of the fractional-turn ratio saturable pulse transformer, but also achieve a quasi-square pulse with high quality and fixed flat top after the modulation of a two-section anti-resonance network. This generator can be applied in areas of large power microwave sources, sterilization, disinfection, and wastewater treatment.

  8. An all-solid-state microsecond-range quasi-square pulse generator based on fractional-turn ratio saturable pulse transformer and anti-resonance network.

    Science.gov (United States)

    Chen, Rong; Yang, Jianhua; Cheng, Xinbing; Pan, Zilong

    2017-03-01

    High voltage pulse generators are widely applied in a number of fields. Defense and industrial applications stimulated intense interests in the area of pulsed power technology towards the system with high power, high repetition rate, solid state characteristics, and compact structure. An all-solid-state microsecond-range quasi-square pulse generator based on a fractional-turn ratio saturable pulse transformer and anti-resonance network is proposed in this paper. This generator consists of a charging system, a step-up system, and a modulating system. In this generator, the fractional-turn ratio saturable pulse transformer is the key component since it acts as a step-up transformer and a main switch during the working process. Demonstrative experiments show that if the primary storage capacitors are charged to 400 V, a quasi-square pulse with amplitude of about 29 kV can be achieved on a 3500 Ω resistive load, as well as the pulse duration (full width at half maximum) of about 1.3 μs. Preliminary repetition rate experiments are also carried out, which indicate that this pulse generator could work stably with the repetition rates of 30 Hz and 50 Hz. It can be concluded that this kind of all-solid-state microsecond-range quasi-square pulse generator can not only lower both the operating voltage of the primary windings and the saturable inductance of the secondary windings, thus ideally realizing the magnetic switch function of the fractional-turn ratio saturable pulse transformer, but also achieve a quasi-square pulse with high quality and fixed flat top after the modulation of a two-section anti-resonance network. This generator can be applied in areas of large power microwave sources, sterilization, disinfection, and wastewater treatment.

  9. Mitigation of Voltage Dip and Voltage Flickering by Multilevel D-STATCOM

    Directory of Open Access Journals (Sweden)

    M. S. Ballal

    2012-01-01

    Full Text Available The basic power quality problems in the distribution network are voltage sag (dip, voltage flickering, and the service interruptions. STATCOM is a Flexible AC Transmission Systems (FACTS technology device which can independently control the flow of reactive power. This paper presents the simulation and analysis of a STATCOM for voltage dip and voltage flickering mitigation. Simulations are carried out in MATLAB/Simulink to validate the performance of the STATCOM. A comparison between the six-pulse inverter and the five-level diode-clamped inverter is carried out for the performance of 66/11 KV distribution system.

  10. Study on the Microsecond Pulse Homogeneous Dielectric Barrier Discharges in Atmospheric Air and Its Influencing Factors%Study on the Microsecond Pulse Homogeneous Dielectric Barrier Discharges in Atmospheric Air and Its Influencing Factors

    Institute of Scientific and Technical Information of China (English)

    方志; 雷枭; 蔡玲玲; 邱毓昌; Edmund KUFFEL

    2011-01-01

    The homogeneous dielectric barrier discharge (DBD) in atmospheric air between two symmetric-columnar copper electrodes with epoxy plates as the dielectric barriers is generated using a us pulse high voltage power supply. The discharge characteristics are studied by measurement of its electrical discharge parameters and observation of its light emission phenom- ena, and the main discharge parameters of the homogenous DBD, such as discharge current and average discharge power, are calculated. Results show that the discharge generated is a homogeneous one with one larger single current pulse of about 2 #s duration appearing in each voltage pulse, and its light emission is radially homogeneous and covers the entire surface of the two elec- trodes. The influences of applied voltage amplitude, air gap distance and barrier thickness on the transition of discharge modes are studied. With the increase of air gap distance, the discharge will transit from homogeneous mode to filamentary mode. The higher the thickness of dielectric barriers, the larger the air gap distance for generating the homogeneous discharge mode. The average discharge power increases non-linearly with increasing applied voltage amplitude, and decreases non-linearly with the increase of air gap distance and barrier thickness. In order to generate stable and homogeneous DBD with high discharge power, thin barriers distance should be used, and higher applied voltage amplitude should be applied to small air gap.

  11. Cryocooled Josephson standards for AC voltage metrology

    Science.gov (United States)

    Durandetto, P.; Sosso, A.; Monticone, E.; Trinchera, B.; Fretto, M.; Lacquaniti, V.

    2017-05-01

    The Josephson effect is worldwide used as a basis for constant reference voltages in national metrological institutes and in calibration laboratories of industry. Research on Josephson voltage standards is aiming at a fundamental change also in the metrology of the volt for AC and arbitrary waveforms: programmable Josephson voltage standards converting a digital code into a quantum-accurate stepwise waveform are already available in primary laboratories and even more advanced standards for converting sub-nanosecond binary coded pulses into any arbitrary signal with quantum accuracy are now actively developed and tested. A new experimental setup based on a two-stage Gifford-McMahon cryocooler has been developed at INRiM for the operation of AC-Josephson voltage standards. Among its distinct features, the possibility of employing both the aforementioned techniques (programmable and pulsed Josephson voltage standards) is particularly interesting. Quantum-based AC voltage sine waves have been synthesized with both programmable and pulse-driven arrays, although their accuracy is still limited by thermal oscillations due to the cryocooler piston motion.

  12. High Voltage Seismic Generator

    Science.gov (United States)

    Bogacz, Adrian; Pala, Damian; Knafel, Marcin

    2015-04-01

    This contribution describes the preliminary result of annual cooperation of three student research groups from AGH UST in Krakow, Poland. The aim of this cooperation was to develop and construct a high voltage seismic wave generator. Constructed device uses a high-energy electrical discharge to generate seismic wave in ground. This type of device can be applied in several different methods of seismic measurement, but because of its limited power it is mainly dedicated for engineering geophysics. The source operates on a basic physical principles. The energy is stored in capacitor bank, which is charged by two stage low to high voltage converter. Stored energy is then released in very short time through high voltage thyristor in spark gap. The whole appliance is powered from li-ion battery and controlled by ATmega microcontroller. It is possible to construct larger and more powerful device. In this contribution the structure of device with technical specifications is resented. As a part of the investigation the prototype was built and series of experiments conducted. System parameter was measured, on this basis specification of elements for the final device were chosen. First stage of the project was successful. It was possible to efficiently generate seismic waves with constructed device. Then the field test was conducted. Spark gap wasplaced in shallowborehole(0.5 m) filled with salt water. Geophones were placed on the ground in straight line. The comparison of signal registered with hammer source and sparker source was made. The results of the test measurements are presented and discussed. Analysis of the collected data shows that characteristic of generated seismic signal is very promising, thus confirms possibility of practical application of the new high voltage generator. The biggest advantage of presented device after signal characteristics is its size which is 0.5 x 0.25 x 0.2 m and weight approximately 7 kg. This features with small li-ion battery makes

  13. A random resistor network model of voltage trimming

    Energy Technology Data Exchange (ETDEWEB)

    Grimaldi, C [Laboratoire de Production Microtechnique, Ecole Polytechnique Federale de Lausanne, CH-1015 Lausanne (Switzerland); Maeder, T [Laboratoire de Production Microtechnique, Ecole Polytechnique Federale de Lausanne, CH-1015 Lausanne (Switzerland); Ryser, P [Laboratoire de Production Microtechnique, Ecole Polytechnique Federale de Lausanne, CH-1015 Lausanne (Switzerland); Straessler, S [Laboratoire de Production Microtechnique, Ecole Polytechnique Federale de Lausanne, CH-1015 Lausanne (Switzerland)

    2004-08-07

    In industrial applications, the controlled adjustment (trimming) of resistive elements via the application of high voltage pulses is a promising technique, with several advantages with respect to more classical approaches such as the laser cutting method. The microscopic processes governing the response to high voltage pulses depend on the nature of the resistor and on the interaction with the local environment. Here we provide a theoretical statistical description of voltage discharge effects on disordered composites by considering random resistor network models with different properties and processes due to the voltage discharge. We compare standard percolation results with biased percolation effects and provide a tentative explanation of the different scenarios observed during trimming processes.

  14. Substrate bias effect on crystallinity of polycrystalline silicon thin films prepared by pulsed ion-beam evaporation method

    Energy Technology Data Exchange (ETDEWEB)

    Ali, Fazlat; Gunji, Michiharu; Yang, Sung-Chae; Suzuki, Tsuneo; Suematsu, Hisayuki; Jiang, Weihua; Yatsui, Kiyoshi [Nagaoka Univ. of Technology, Extreme Energy-Density Research Inst., Nagaoka, Niigata (Japan)

    2002-06-01

    The deposition of polycrystalline silicon thin films has been tried by a pulsed ion-beam evaporation method, where high crystallinity and deposition rate have been achieved without heating the substrate. The crystallinity and the deposition rate were improved by applying bias voltage to the substrate, where instantaneous substrate heating might have occurred by ion-bombardment. (author)

  15. 极低频高压脉冲电场对萌发玉米种子超弱发光的影响%Effect of Extremely Low Frequency High-voltage Pulsed Electric Field on Ultra-weak Luminescence of Corns during Germination

    Institute of Scientific and Technical Information of China (English)

    习岗; 刘锴; 杨运经; 高宇

    2013-01-01

    生物超弱发光是来自细胞的电磁信号,在揭示电磁生物学效应的机理研究中具有重要作用.为了研究极低频脉冲电场生物学效应及其机理,采用基于玉米细胞电位波动频率的1 Hz极低频高压脉冲电场处理萌发玉米种子,结果发现玉米种子的萌发过程明显加快,根长和芽长均有显著增长.对萌发种子的自发发光和延迟发光的测量结果显示,1 Hz极低频高压脉冲电场对萌发过程中玉米种子的自发发光和延迟发光积分强度都有明显的促进作用,表明1 Hz极低频高压脉冲电场加速了玉米种子萌发过程中的DNA合成和细胞代谢.%Biological ultra-weak luminescence is an electromagnetic signal from cells,which plays an important role in revealing the mechanism of electromagnetic biological effects.In order to study the biological effects and mechanism of extremely low frequency pulsed electric field,1 Hz extremely low frequency high-voltage pulsed electric field based on the potential fluctuation frequency of corn cells was used to treat the corns during germination.The results showed that the germination process of corns was accelerated obviously and both the shoot length and root length of germinating corns were significantly longer than the control.Through the measurement and analysis of spontaneous luminescence and delayed luminescence on corns during germination,it was found that the spontaneous luminescence and delayed luminescence integral intensity of germinating corn were significantly increased under the action of 1 Hz extremely low frequency high-voltage pulsed electric field,which indicated that this specific pulsed electric field promoted the DNA synthesis and cell metabolism of the corns during germination.The coupled resonance of pulsed electric field and cell electric field in corn seeds may be the cause of biological effects of the extremely low frequency high-voltage pulsed electric field.

  16. 高压电力计量系统故障诊断与应用研究%The Fault Diagnosis and Applied Research of High Voltage Electric Power Metering System

    Institute of Scientific and Technical Information of China (English)

    王娟; 张瑾

    2013-01-01

    提出了一种新的应用于高压电力计量系统的电流互感器一次侧短路的故障检测方法.首先,通过理论分析得出网络阻抗与电流互感器一次侧短路之间的密切关系.其次,设计故障检测方法,对故障信号进行分析和研究.最后得出了一种在实际应用中可行的方案.%A new fault detection method of short circuit of the primary side of TA applied to high voltage electric power metering system is proposed.Firstly,through theory analysis the close relationship between network impedance and short circuit of the primary side of TA are obtained.Secondly,the method of fault detection to research and analyze the fault signal is designed.Lastly,a plan is obtained that is feasible in practical application.

  17. SIMULACIÓN DE MONTE CARLO APLICADA A LA ESTIMACIÓN DE DEPRESIONES RÁPIDAS DE LA TENSIÓN EN REDES ELÉCTRICAS MONTE CARLO SIMULATION APPLIED TO THE ESTIMATION OF VOLTAGE DIPS IN ELECTRIC NETWORKS

    Directory of Open Access Journals (Sweden)

    Miguel Arias Albornoz

    2008-09-01

    Full Text Available En este trabajo se aplica el método de simulación de Monte Carlo (MC para estimar el número de depresiones rápidas de tensión (dips esperados en barras de una red eléctrica. Las estimaciones obtenidas a través de MC se comparan con los resultados de otro método de cálculo conocido como Método de Posiciones de Falla (MPF. Entre los resultados se muestra tanto la convergencia del algoritmo MC a los valores de largo plazo del método MPF como la distribución completa de frecuencias para diferentes eventos, lo cual representa información valiosa para apoyar la toma de decisiones sobre el empleo de equipos sensibles a este tipo de perturbación.In this work, the Monte Carlo simulation method (MC is applied to estimate the number of expected voltage dips in the nodes of an electric network. The estimations obtained through MC are compared with the results of another method of calculation, known as Failure Position Method (MPF. In the results, both the convergence of the algorithm with the long-term values of the MPF method and the complete distribution of frequencies for different events are shown. This represents valuable information to support the decision-making process for equipment that is sensitive to this type of perturbation.

  18. Pulsed electrical discharge in conductive solution

    Science.gov (United States)

    Panov, V. A.; Vasilyak, L. M.; Vetchinin, S. P.; Pecherkin, V. Ya; Son, E. E.

    2016-09-01

    Electrical discharge in a conductive solution of isopropyl alcohol in tap water (330 μ S cm-1) has been studied experimentally applying high voltage millisecond pulses (rise time  ˜0.4 μ \\text{s} , amplitude up to 15 kV, positive polarity) to a pin anode electrode. Dynamic current-voltage characteristics synchronized with high-speed images of the discharge were studied. The discharge was found to develop from high electric field region in the anode vicinity where initial conductive current with density  ˜100 A cm-2 results in fast heating and massive nucleation of vapor bubbles. Discharges in nucleated bubbles then produce a highly conductive plasma region and facilitate overheating instability development with subsequent formation of a thermally ionized plasma channel. The measured plasma channel propagation speed was 3-15 m s-1. A proposed thermal model of plasma channel development explains the low observed plasma channel propagation speed.

  19. Improving thrust by pulse-induced breakdown enhancement in AC surface dielectric barrier discharge actuators for airflow control

    Science.gov (United States)

    Yan, Huijie; Yang, Liang; Qi, Xiaohua; Ren, Chunsheng

    2016-07-01

    The characteristics of a plate-to-plate AC surface dielectric barrier discharge (SDBD) actuator using the pulse-induced breakdown enhancing method are experimentally investigated. The encapsulated electrode is supplied with a sine high AC voltage, while the exposed electrode is feed by a synchronized pulse voltage. Based on the thrust force and power consumption measurements, a parametric study was performed using a positive pulse applied at the trough phase of the AC cycles in which the thrust force was observed to increase by about 100% to 300% and the efficiency up to about 100% compared with the AC-only supply conditions for different AC voltages within the tested range. The pulse-induced breakdown effect was analyzed from the electrical and light emission waveforms to reveal the underlying mechanism. The surface potential due to the charge deposition effect was also measured using a specially designed corona-like discharge potential probe. It is shown that the pulse-induced breakdown was able to cause a temporarily intensified local electric field to enhance the glow-like discharge and meanwhile increase the time-average surface potential in the region further downstream. The improvement in the force by the enhancement in the pulse-induced breakdown was mainly due to enhancements in the glow-like discharge and the surface potential increment, with the latter being more important when the AC voltage is higher.

  20. Pulse Response Measurement Aiming for Locating Water Tree Degradation in XLPE Cables

    Science.gov (United States)

    Hiei, Susumu; Hozumi, Naohiro; Kurihara, Takashi; Okamoto, Tatsuki; Uchida, Katsumi; Tsuji, Taizo

    Water treeing is a degradation mode of power cable with polymeric insulation. A water tree is composed of small droplets filled with water. As the conductivity in water tree is very high, it leads to dielectric breakdown when it grows up. As inside of the water tree is filled with trap sites, it is polarized with a certain distribution of relaxation time when a DC poling voltage is applied. Although its depolarization process after removing the poling voltage is determined by ambient temperature, applying a “depolarizing voltage” with the opposite polarity can accelerate the process. If a short pulse propagating through the cable is employed as a depolarization voltage, we may locate the water tree through looking at the time-resolved pulse response. This would lead to a diagnosing method with spatial resolution. In order to retain 100 m of spatial resolution, the response should be as sharp as 1 μs. As a preliminary study, a coaxial communication cable was aged to form water trees. A DC poling voltage was applied followed by a pulse voltage with opposite polarity. The rising time of the pulse was several hundreds of microseconds. A sharp pulse current response with 50 μs in width was observed, suggesting that a rapid depolarization took place. No such response was seen when the cable specimen was not aged. We concluded that the technique is quite feasible. As the response was found to be as quick as several microseconds, an experiment using 405 m-long cable, with 5 m of degraded length in the middle, was performed. It was shown that the degraded point was successfully located.

  1. A voltage-dependent persistent sodium current in mammalian hippocampal neurons

    OpenAIRE

    1990-01-01

    Currents generated by depolarizing voltage pulses were recorded in neurons from the pyramidal cell layer of the CA1 region of rat or guinea pig hippocampus with single electrode voltage-clamp or tight- seal whole-cell voltage-clamp techniques. In neurons in situ in slices, and in dissociated neurons, subtraction of currents generated by identical depolarizing voltage pulses before and after exposure to tetrodotoxin revealed a small, persistent current after the transient current. These curren...

  2. Reversal transient laser-induced voltages in La2/3Ca1/3MnO3 films

    Institute of Scientific and Technical Information of China (English)

    Zhao Kun; He Meng; Lü Hui-Bin

    2007-01-01

    This paper reports that the transient laser-induced voltages have been observed in La2/3Ca1/3MnO3 thin films on MgO (001) in the absence of an applied current.A peak voltage of~0.15V Was detected in response to 0.015 J pulse of 308 nm laser.It is demonstrated that the signal polarity is reversed when the films are irradiated through the substrate rather than at the air/film interface.Off-diagonal thermoelectricity may support the inversion of the signal when the irradiation direction is reversed.

  3. Effect of high-voltage pulsed current plus conventional treatment on acute ankle sprain Efeito da adição da estimulação de alta voltagem ao tratamento convencional do entorse de tornozelo numa etapa aguda

    Directory of Open Access Journals (Sweden)

    Maria Cristina Sandoval

    2010-06-01

    Full Text Available BACKGROUND: The effectiveness of high-voltage pulsed current (HVPC treatments in humans as a means of controlling edema and post-traumatic pain has not yet been established. Objective: To analyze the effects of HVPC plus conventional treatment on lateral ankle sprains. METHODS: This was a randomized, controlled, double-blind clinical trial with three intervention groups: CG (control group with conventional treatment; HVPC(- group (conventional treatment plus negative polarity HVPC; HVPC(+ group (conventional treatment plus positive polarity HVPC. Twenty-eight participants with lateral ankle sprain (2 to 96h post-trauma were evaluated. Conventional treatment consisted of cryotherapy (20min plus therapeutic exercises. Additionally, the HVPC(- and HVPC(+ groups received 30min of electrical stimulation (submotor level; 120 pps. Pain, edema, range of motion (ROM and gait were assessed before the first treatment session and after the last treatment session. RESULTS: At the final evaluation, there were no significant differences between groups. Nevertheless, the HVPC(- group had greater values in all assessed parameters. The data analysis showed that the HVPC(- group had greater reductions in volume and girth, and greater recovery of ROM and gait velocity. This group also reached the end of the treatment (1.7 weeks; range 1.2-2.2 faster than the HVPC(+ group and the CG (2.2 weeks; range 1.8-2.6. CONCLUSIONS: There were no differences between the study groups, but the results suggest that HVPC(- can accelerate the initial phase of recovery from ankle sprain.CONTEXTUALIZAÇÃO: A eficácia da estimulação elétrica de alta voltagem (EEAV em humanos, como uma forma de tratamento para controlar o edema e a dor pós-traumáticos, ainda não foi estabelecida. OBJETIVO: Analisar o efeito da adição da EEAV ao tratamento convencional do pós-entorse de tornozelo em humanos. MÉTODOS: Ensaio clínico controlado e aleatorizado, duplo cego com três grupos de

  4. Hydrogeology from 10,000 ft below: lessons learned in applying pulse testing for leakage detection in a carbon sequestration formation

    Science.gov (United States)

    Sun, A. Y.; Lu, J.; Hovorka, S. D.; Freifeld, B. M.; Islam, A.

    2015-12-01

    Monitoring techniques capable of deep subsurface detection are desirable for early warning and leakage pathway identification in geologic carbon storage formations. This work investigates the feasibility of a leakage detection technique based on pulse testing, which is a traditional hydrogeological characterization tool. In pulse testing, the monitoring reservoir is stimulated at a fixed frequency and the acquired pressure perturbation signals are analyzed in the frequency domain to detect potential deviations in the reservoir's frequency domain response function. Unlike traditional time-domain analyses, the frequency-domain analysis aims to minimize the interference of reservoir noise by imposing coded injection patterns such that the reservoir responses to injection can be uniquely determined. We have established the theoretical basis of the approach in previous work. Recently, field validation of this pressure-based, leakage detection technique was conducted at a CO2-EOR site located in Mississippi, USA. During the demonstration, two sets of experiments were performed using 90-min and 150-min pulsing periods, for both with and without leak scenarios. Because of the lack of pre-existing leakage pathways, artificial leakage CO2 was simulated by rate-controlled venting from one of the monitoring wells. Our results show that leakage events caused a significant deviation in the amplitude of the frequency response function, indicating that pulse testing may be used as a cost-effective monitoring technique with a strong potential for automation.

  5. A Synchrophasor Based Optimal Voltage Control Scheme with Successive Voltage Stability Margin Improvement

    Directory of Open Access Journals (Sweden)

    Heng-Yi Su

    2016-01-01

    Full Text Available This paper proposes an optimal control scheme based on a synchronized phasor (synchrophasor for power system secondary voltage control. The framework covers voltage stability monitoring and control. Specifically, a voltage stability margin estimation algorithm is developed and built in the newly designed adaptive secondary voltage control (ASVC method to achieve more reliable and efficient voltage regulation in power systems. This new approach is applied to improve voltage profile across the entire power grid by an optimized plan for VAR (reactive power sources allocation; therefore, voltage stability margin of a power system can be increased to reduce the risk of voltage collapse. An extensive simulation study on the IEEE 30-bus test system is carried out to demonstrate the feasibility and effectiveness of the proposed scheme.

  6. Influence of the work in high voltage in the health of the man (behavioral of the arterial stress and pulse); Influencia do trabalho em alta tensao na saude do homem (comportamento da pressao arterial e pulso)

    Energy Technology Data Exchange (ETDEWEB)

    Hellmeister, C.R.; Ferreira, B.J.; Rodrigues, M.A.F. [Companhia Paulista de Forca e Luz, Campinas, SP (Brazil); Fernandes, C.; Franca, A.M. [Centro de Pesquisas de Energia Eletrica, Rio de Janeiro, RJ (Brazil)

    1987-12-31

    This work aims to observe the probable alterations of the arterial pressure and pulse, in function of the physical stress, in a determined routine of job, in the presence of the electromagnetic field 8 refs., 10 figs., 1 tab.

  7. The Role of Additional Pulses in Electropermeabilization Protocols

    Science.gov (United States)

    Suárez, Cecilia; Soba, Alejandro; Maglietti, Felipe; Olaiz, Nahuel; Marshall, Guillermo

    2014-01-01

    Electropermeabilization (EP) based protocols such as those applied in medicine, food processing or environmental management, are well established and widely used. The applied voltage, as well as tissue electric conductivity, are of utmost importance for assessing final electropermeabilized area and thus EP effectiveness. Experimental results from literature report that, under certain EP protocols, consecutive pulses increase tissue electric conductivity and even the permeabilization amount. Here we introduce a theoretical model that takes into account this effect in the application of an EP-based protocol, and its validation with experimental measurements. The theoretical model describes the electric field distribution by a nonlinear Laplace equation with a variable conductivity coefficient depending on the electric field, the temperature and the quantity of pulses, and the Penne's Bioheat equation for temperature variations. In the experiments, a vegetable tissue model (potato slice) is used for measuring electric currents and tissue electropermeabilized area in different EP protocols. Experimental measurements show that, during sequential pulses and keeping constant the applied voltage, the electric current density and the blackened (electropermeabilized) area increase. This behavior can only be attributed to a rise in the electric conductivity due to a higher number of pulses. Accordingly, we present a theoretical modeling of an EP protocol that predicts correctly the increment in the electric current density observed experimentally during the addition of pulses. The model also demonstrates that the electric current increase is due to a rise in the electric conductivity, in turn induced by temperature and pulse number, with no significant changes in the electric field distribution. The EP model introduced, based on a novel formulation of the electric conductivity, leads to a more realistic description of the EP phenomenon, hopefully providing more accurate

  8. Multichannel computerized control system of current pulses in LIU-30 electron accelerator

    CERN Document Server

    Gerasimov, A I; Kulgavchuk, V V; Pluzhnikov, A V

    2002-01-01

    In LIU-30 power linear pulsed induction electron accelerator (40 MeV, 10 kA, 25 ns) 288 radial lines with water insulation serve as energy accumulators and shapers of accelerating voltage pulses. The lines are charged simultaneously up to 500 kV using a system comprising 72 Arkadiev-Marx screened generators. To control parameter of synchronous pulses of charging current with up to 60 kA amplitude and 0.85 mu s duration in every of 72 charging circuits one applies a computer-aided system. Current pulse is recorded at output of every generator using the Rogowski coil signal from which via a cable line is transmitted to an analog-digital converter, is processed with 50 ns sampling and is recorded to a memory unit. Upon actuation of accelerator the signals are sequentially or selectively displayed and are compared with pulse typical shape

  9. Evidence of surface charge effects in T-branch nanojunctions using microsecond-pulse testing

    Energy Technology Data Exchange (ETDEWEB)

    Iniguez-de-la-Torre, I; Mateos, J; Gonzalez, T [Departamento de Fisica Aplicada, Universidad de Salamanca, Plaza de la Merced s/n, 37008 Salamanca (Spain); Roelens, Y; Gardes, C; Bollaert, S [Institut d' Electronique de Microelectronique et de Nanotechnologie (IEMN), UMR CNRS 8520, Universite de Lille 1, Avenue Poincare BP60069, 59652, Villeneuve d' Ascq CEDEX (France)

    2011-11-04

    The understanding of the influence of surface charge effects on the electrical properties of nanostructures is a key aspect for the forthcoming generations of electronic devices. In this paper, by using an ultrafast electrical pulse characterization technique, we report on the room-temperature time response of a T-branch nanojunction which allows us to identify the signature of surface states. Different pulse widths from 500 ns to 100 {mu}s were applied to the device. For a given pulse width, the stem voltage is measured and compared with the DC result. The output value in the stem is found to depend on the pulse width and to be related to the characteristic charging time of the interface states. As expected, the results show that the well-known nonlinear response of T-branch junctions is more pronounced for long pulses, beyond such a characteristic time.

  10. Synchronized and timing-stabilized pulse generation from a gain-switched laser diode for stimulated Raman scattering microscopy

    Science.gov (United States)

    Tokunaga, Kyoya; Fang, Yi-Cheng; Yokoyama, Hiroyuki; Ozeki, Yasuyuki

    2016-03-01

    We present a picosecond laser source based on a gain-switched laser diode (GS-LD) that can be applied to stimulated Raman scattering (SRS) microscopy. A 1.06-μm GS-LD was used to generate 14-ps pulses at a repetition rate of 38 MHz. The GS-LD was driven by 200-ps electrical pulses, which were triggered through a toggle flip-flop (T-FF). As a result, the GS-LD pulses were subharmonically synchronized to Ti:sapphire laser (TSL) pulses at a repetition rate of 76 MHz. We investigated the timing jitter of GS-LD pulses and found it to be less than 2.5 ps. We also show that the trigger delay can be less sensitive to the optical power of TSL pulses by controlling the threshold voltage of the T-FF. As a result, GS-LD pulses sufficiently overlapped with TSL pulses even when we scanned the wavelength of the TSL pulses. We demonstrate the SRS imaging of HeLa cells with GS-LD pulses and TSL pulses, proving that GS-LD is readily applicable to SRS microscopy as a compact and stable pulse source.

  11. Linearity of P-N junction photodiodes under pulsed irradiation

    CERN Document Server

    Stuik, R

    2002-01-01

    The dependence of the sensitivity on the radiation pulse length for a P-N junction photodiode has been investigated over an extended range of pulse lengths, from 170 ns to 1.2 ms. The power incident on the diode surface was varied between 1.6 and 118 mW. A novel method was used to generate the light pulses with variable length, while keeping the temporal pulse shape and the intensity constant. The method consists of using a rotating mirror in combination with a DC light source, in our case at 633 and 532 nm. In this way, the pulse shape only depends on the geometry of the setup, with the pulse length solely determined by the rotation frequency of the mirror. No further calibration is needed for determination of the pulse intensity and shape. Accuracies obtained are better than 2%, mainly determined by instabilities in the setup. The sensitivity of an IRD AXUV-100 photodiode was studied, both with and without a reverse bias voltage applied. At unbiased conditions and irradiation levels well below the saturatio...

  12. Simulation of pulsed dielectric barrier discharge xenon excimer lamp

    Science.gov (United States)

    Bogdanov, E. A.; Kudryavtsev, A. A.; Arslanbekov, R. R.; Kolobov, V. I.

    2004-11-01

    Recently, it has been shown that the efficiency of excimer lamps can be drastically increased in a pulsed regime. A one-dimensional simulation of pulsed excimer lamps has been performed by Carman and Mildren (2003 J. Phys. D: Appl. Phys. 36 19) (C&M). However, some computational results of the work of C&M are questionable and need to be revisited. In this paper, a dielectric barrier discharge (DBD) in xenon has been simulated for operating conditions similar to those of C&M to better understand plasma dynamics in a pulsed regime. Our simulation results differ considerably from the computational results of C&M. Although these differences do not affect profoundly the plasma macro parameters measured in the C&M experiments, they offer a better understanding of plasma dynamics in pulsed DBDs and form a solid foundation for computational optimization of excimer lamps. It was found that the dynamics of breakdown and the current pulse depend significantly on the initial densities of species after a previous pulse, and so it is important to accurately simulate the plasma evolution in both the afterglow and active stages. It seems possible to modify the power deposition in the plasma by varying external discharge parameters such as the amplitude and the rise time of the applied voltage, and to modify the plasma composition by changing the pulse repetition rate and plasma decay in the afterglow stage.

  13. Simulation of pulsed dielectric barrier discharge xenon excimer lamp

    Energy Technology Data Exchange (ETDEWEB)

    Bogdanov, E A [St Petersburg State University, St Petersburg (Russian Federation); Kudryavtsev, A A [St Petersburg State University, St Petersburg (Russian Federation); Arslanbekov, R R [CFD Research Corporation, Huntsville (United States); Kolobov, V I [CFD Research Corporation, Huntsville (United States)

    2004-11-07

    Recently, it has been shown that the efficiency of excimer lamps can be drastically increased in a pulsed regime. A one-dimensional simulation of pulsed excimer lamps has been performed by Carman and Mildren (2003 J. Phys. D: Appl. Phys. 36 19) (C and M). However, some computational results of the work of C and M are questionable and need to be revisited. In this paper, a dielectric barrier discharge (DBD) in xenon has been simulated for operating conditions similar to those of C and M to better understand plasma dynamics in a pulsed regime. Our simulation results differ considerably from the computational results of C and M. Although these differences do not affect profoundly the plasma macro parameters measured in the C and M experiments, they offer a better understanding of plasma dynamics in pulsed DBDs and form a solid foundation for computational optimization of excimer lamps. It was found that the dynamics of breakdown and the current pulse depend significantly on the initial densities of species after a previous pulse, and so it is important to accurately simulate the plasma evolution in both the afterglow and active stages. It seems possible to modify the power deposition in the plasma by varying external discharge parameters such as the amplitude and the rise time of the applied voltage, and to modify the plasma composition by changing the pulse repetition rate and plasma decay in the afterglow stage.

  14. Shaping the spectra of the line-to-line voltage using signal injection in the common mode voltage

    DEFF Research Database (Denmark)

    Mathe, Laszlo; Rasmussen, Peter Omand; Pedersen, John Kim

    2009-01-01

    A drawback of Pulse Width Modulation in electrical drives is the high harmonic content of the line to line voltages, which gives rise to Electro-Magnetic Interference and acoustic noise. By injection of a signal into the common mode voltage, the fundamental is not affected, but new frequency...... components are introduced in the line to line voltage spectrum. This paper introduces a new analytical method for estimation of the line to line voltage spectrum, where sinusoidal signal is injected into the common mode voltage. Based on the analytical calculations, also a new fixed carrier frequency quasi...

  15. Comparison of Algorithms for Control of Loads for Voltage Regulation

    DEFF Research Database (Denmark)

    Douglass, Philip James; Han, Xue; You, Shi

    2014-01-01

    Autonomous flexible loads can be utilized to regulate voltag e on low voltage feeders. This paper compares two algorithms for controllin g loads: a simple voltage droop, where load power consumption is a varied in proportio n to RMS voltage; and a normalized relative voltage droop, which modifies...... the simpl e voltage droop by subtracting the mean voltage value at the bus and dividing by the standard deviation. These two controllers are applied to hot water heaters simul ated in a simple residential feeder. The simulation results show that both controllers r educe the frequency of undervoltage events...

  16. Transient Voltage Recorder

    Science.gov (United States)

    Medelius, Pedro J. (Inventor); Simpson, Howard J. (Inventor)

    2002-01-01

    A voltage transient recorder can detect lightning induced transient voltages. The recorder detects a lightning induced transient voltage and adjusts input amplifiers to accurately record transient voltage magnitudes. The recorder stores voltage data from numerous monitored channels, or devices. The data is time stamped and can be output in real time, or stored for later retrieval. The transient recorder, in one embodiment, includes an analog-to-digital converter and a voltage threshold detector. When an input voltage exceeds a pre-determined voltage threshold, the recorder stores the incoming voltage magnitude and time of arrival. The recorder also determines if its input amplifier circuits clip the incoming signal or if the incoming signal is too low. If the input data is clipped or too low, the recorder adjusts the gain of the amplifier circuits to accurately acquire subsequent components of the lightning induced transients.

  17. Reducing error rates in straintronic multiferroic nanomagnetic logic by pulse shaping.

    Science.gov (United States)

    Munira, Kamaram; Xie, Yunkun; Nadri, Souheil; Forgues, Mark B; Fashami, Mohammad Salehi; Atulasimha, Jayasimha; Bandyopadhyay, Supriyo; Ghosh, Avik W

    2015-06-19

    Dipole-coupled nanomagnetic logic (NML), where nanomagnets (NMs) with bistable magnetization states act as binary switches and information is transferred between them via dipole-coupling and Bennett clocking, is a potential replacement for conventional transistor logic since magnets dissipate less energy than transistors when they switch in a logic circuit. Magnets are also 'non-volatile' and hence can store the results of a computation after the computation is over, thereby doubling as both logic and memory-a feat that transistors cannot achieve. However, dipole-coupled NML is much more error-prone than transistor logic at room temperature [Formula: see text] because thermal noise can easily disrupt magnetization dynamics. Here, we study a particularly energy-efficient version of dipole-coupled NML known as straintronic multiferroic logic (SML) where magnets are clocked/switched with electrically generated mechanical strain. By appropriately 'shaping' the voltage pulse that generates strain, we show that the error rate in SML can be reduced to tolerable limits. We describe the error probabilities associated with various stress pulse shapes and discuss the trade-off between error rate and switching speed in SML.The lowest error probability is obtained when a 'shaped' high voltage pulse is applied to strain the output NM followed by a low voltage pulse. The high voltage pulse quickly rotates the output magnet's magnetization by 90° and aligns it roughly along the minor (or hard) axis of the NM. Next, the low voltage pulse produces the critical strain to overcome the shape anisotropy energy barrier in the NM and produce a monostable potential energy profile in the presence of dipole coupling from the neighboring NM. The magnetization of the output NM then migrates to the global energy minimum in this monostable profile and completes a 180° rotation (magnetization flip) with high likelihood.

  18. Study on the Test Method of Initiation Energy Matching for High Voltage Pulse Power Source and Slapper%高压脉冲功率源与冲击片雷管发火能量匹配关系特性试验方法

    Institute of Scientific and Technical Information of China (English)

    韩克华; 王丽萍; 任西; 褚恩义

    2012-01-01

    Aimed at the problem of initiation energy matching for high voltage pulse power source with cable and slapper, the test method of initiation energy matching was put forward. For the cable connected to the output of high voltage pulse power source condition, the data of the short circuit discharge were obtained by the test device, meanwhile, the theoretic analysis and verification test of slapper initiation were carried out The results indicated that when the cable of 100mm was connected to the output of high voltage pulse power source, the initiation voltage of slapper was risen 300V, the corresponding output energy equals to that without cable. The test method not only protect the initiation device and retrench the test cost, but also ensure the reliability of slapper initiation.%针对高压脉冲功率源接入引出电缆后与冲击片雷管发火能量的匹配问题,提出了高压脉冲功率源与冲击片雷管发火能量的匹配关系特性试验方法,通过试验装置测试了接入引出电缆后冲击片雷管短路放电性能参数,并进行了理论分析及冲击片雷管发火验证试验.结果表明:在脉冲功率源输出端增加100mm的引出电缆后,冲击片雷管发火电压需提升300V,此时输出能量等价于未接入引出电缆时的发火能量.该方法在冲击片雷管发火试验以及传爆序列试验中,既能保护起爆装置,节约试验成本,又能保证冲击片雷管可靠起爆.

  19. 两电平空间矢量脉宽调制的简化算法和电压谐波分析方法%A Simplified Algorithm and A Method of Voltage Harmonic Analysis for Two-Level Space Vector Pulse Width Modulation

    Institute of Scientific and Technical Information of China (English)

    于心宇; 魏应冬; 姜齐荣

    2014-01-01

    传统的两电平空间矢量脉宽调制(space vector pulse width modulation,SVPWM)算法流程复杂,计算量较大。从传统算法的伏秒平衡方程出发,推导并求解了三相上开关器件脉宽时间所满足的线性方程组,提出了一种无需坐标变换和扇区判断的两电平 SVPWM 简化算法。该算法流程简单,计算量少,且在参考电压含不对称分量时仍与传统算法等价。在此基础上,针对采用同步 SVPWM 的两电平变流器,提出了一种电压谐波分析方法,给出了在不同零矢量分配方式下通用的电压谐波频谱计算公式,并定性分析了电压谐波的频谱分布特性。基于PSCAD/EMTDC的仿真结果验证了所提的两电平 SVPWM 简化算法和电压谐波分析方法的准确性。%The traditional algorithm for 2-level space vector pulse width modulation (SVPWM) is complicated with large computation. In this paper, based on the volt-second balance equation of traditional algorithm, the linear equations of the pulse time of switching devices in 3-phase upper arms are set up and solved, thus a simplified algorithm for 2-level SVPWM without coordinate transformation and sector judgment is proposed, which reduces a lot of computation and is much easier to implement. Based on the simplified algorithm, a method of voltage harmonic analysis for synchronous SVPWM is proposed, which presents the generic expressions of the voltage harmonic spectrum when the distribution of zero vectors is varied, and explains the distribution characteristics of voltage harmonics qualitatively. The accuracy of the simplified algorithm and the novel method of voltage harmonic analysis for 2-level SVPWM are verified by the simulation results based on PSCAD/EMTDC.

  20. The effectiveness of nutrition education: Applying the Health Belief Model in child-feeding practices to use pulses for complementary feeding in Southern Ethiopia.

    Science.gov (United States)

    Mulualem, Demmelash; Henry, Carol J; Berhanu, Getenesh; Whiting, Susan J

    2016-01-01

    Complementary foods (CFs) in Ethiopia are cereal based and adding locally grown pulses (legumes) to CF would provide needed nutrients. To assess the effects of nutrition education (NEd) using Health Belief Model (HBM) in promoting pulses for CF, a 6-month quasi-experimental study was conducted in 160 mother-child pairs. Knowledge, attitude, and practice (KAP) questions were given to mothers at baseline, midline, and endline, along with anthropometric measurements of children. NEd involving discussions and recipe demonstrations was given twice monthly for 6 months to the intervention group (n = 80) while control mothers received usual education. At baseline, mothers' KAP scores were low at both sites; at 3 and 6 months of NEd, mean KAP scores of mothers increased (p < 0.05) compared to the control site. Significant improvements in children's mean weight, weight for height, and weight for age occurred in the intervention site only. Nutritional status of children improved after providing mothers with pulse-based NEd.

  1. Theoretical Studies of the Output Pulse with Variation of the Pumping Pulse for RF Excited CO2 Pulsed Waveguide Laser

    Institute of Scientific and Technical Information of China (English)

    A Rauf; ZHOU Wei; XIN Jian-guo

    2006-01-01

    The behavior of a RF-excited waveguide CO2 laser in the pulse regime is studied theoretically. The output pulse evolution is studied by applying three types of pulses namely the square, sine and the triangular ones as the excitation pulses. The frequency dependence behavior of the output pulse is also presented.

  2. Discharge and optical characterizations of nanosecond pulse sliding dielectric barrier discharge plasma for volatile organic compound degradation

    Science.gov (United States)

    Jiang, Nan; Guo, Lianjie; Shang, Kefeng; Lu, Na; Li, Jie; Wu, Yan

    2017-04-01

    In this work, a nanosecond bipolar pulsed voltage coupled with a negative DC component is employed to generate sliding dielectric barrier discharge (DBD) plasma in a three-electrode geometry reactor and improve volatile organic compound (VOC) degradation at room temperature. The effects of the bipolar pulsed voltage (U ±pulse) and negative DC voltage (U ‑DC) on the discharge characteristic, optical characteristic, plasma gas temperature (T gas), and vibrational temperature (T vib) are discussed. The horizontal distribution characteristics of the N2(C3Πu  →  B3Πg) emission intensity, T gas, and T vib are also investigated to understand the propagation mechanism of sliding DBD along the dielectric surface. The experimental results reveal that a negative DC component applied to a third electrode can extend the plasma extension region, indicating that the gas ionization is ignited by the nanosecond high-voltage pulse, while charge drift is forced by the surface potential difference caused by the negative high-voltage DC. The T gas is measured by optical emission spectroscopy related to the rotational bands of N2(C3 Πu  →  B3Πg), and is approximately 375  ±  5 K under the condition of U ±pulse  =  20 kV and U ‑DC  =  ‑20 kV. Compared with typical surface DBD plasma, sliding DBD plasma is quasi-diffusive and distributed more uniformly within the whole discharge gap. Furthermore, both surface DBD and sliding DBD are used for removing toluene from flowing air. It is found that sliding DBD has higher toluene degradation efficiency and energy yield than surface DBD when they are excited by the positive pulsed voltage (U +pulse).

  3. Dynamic parabolic pulse generation using temporal shaping of wavelength to time mapped pulses.

    Science.gov (United States)

    Nguyen, Dat; Piracha, Mohammad Umar; Mandridis, Dimitrios; Delfyett, Peter J

    2011-06-20

    Self-phase modulation in fiber amplifiers can significantly degrade the quality of compressed pulses in chirped pulse amplification systems. Parabolic pulses with linear frequency chirp are suitable for suppressing nonlinearities, and to achieve high peak power pulses after compression. In this paper, we present an active time domain technique to generate parabolic pulses for chirped pulse amplification applications. Pulses from a mode-locked laser are temporally stretched and launched into an amplitude modulator, where the drive voltage is designed using the spectral shape of the input pulse and the transfer function of the modulator, resulting in the generation of parabolic pulses. Experimental results of pulse shaping with a pulse train from a mode-locked laser are presented, with a residual error of less than 5%. Moreover, an extinction ratio of 27 dB is achieved, which is ideal for chirped pulse amplification applications.

  4. An Optoelectronic High-voltage Probe for Measuring Impulse Voltage Distribution of HVDC Converter Valve

    Institute of Scientific and Technical Information of China (English)

    方志; 邱毓昌

    2007-01-01

    A high-voltage optoelectronic probe is developed for measuring impulse voltage distribution along thyristor units in the HVDC converter valve. The dimension of the resistive voltage divider is optimized by means of numerical compttation of electric field. A pulse frequency modulation (PFM) mode is adopted for the data transmission link because of its immunity to high-intensity electromagnetic interference. Experimental results indicate that the linearity deviation for the whole measuring system is within ± 0.15 %, and therefore it can meet requirements specified by IEC60700-1.

  5. Neutron induced current pulses in fission chambers. [LMFBR

    Energy Technology Data Exchange (ETDEWEB)

    Taboas, A L; Buck, W L

    1978-01-01

    The mechanism of neutron induced current pulse generation in fission chambers is discussed. By application of the calculated detector transfer function to proposed detector current pulse shapes, and by comparison with actually observed detector output voltage pulses, a credible, semi-empirical, trapezoidal pulse shape of chamber current is obtained.

  6. Automatic voltage imbalance detector

    Science.gov (United States)

    Bobbett, Ronald E.; McCormick, J. Byron; Kerwin, William J.

    1984-01-01

    A device for indicating and preventing damage to voltage cells such as galvanic cells and fuel cells connected in series by detecting sequential voltages and comparing these voltages to adjacent voltage cells. The device is implemented by using operational amplifiers and switching circuitry is provided by transistors. The device can be utilized in battery powered electric vehicles to prevent galvanic cell damage and also in series connected fuel cells to prevent fuel cell damage.

  7. Comparison of Twitch Responses During Current- or Voltage-Controlled Transcutaneous Neuromuscular Electrical Stimulation.

    Science.gov (United States)

    Vargas Luna, José Luis; Krenn, Matthias; Löfler, Stefan; Kern, Helmut; Cortés R, Jorge A; Mayr, Winfried

    2015-10-01

    Neuromuscular electrical stimulation (NMES) is an established method for functional restoration of muscle function, rehabilitation, and diagnostics. In this work, NMES was applied with surface electrodes placed on the anterior thigh to identify the main differences between current-controlled (CC) and voltage-controlled (VC) modes. Measurements of the evoked knee extension force and the myoelectric signal of quadriceps and hamstrings were taken during stimulation with different amplitudes, pulse widths, and stimulation techniques. The stimulation pulses were rectangular and symmetric biphasic for both stimulation modes. The electrode-tissue impedance influences the differences between CC and VC stimulation. The main difference is that for CC stimulation, variation of pulse width and amplitude influences the amount of nerve depolarization, whereas VC stimulation is only dependent on amplitude variations for pulse widths longer than 150 μs. An important remark is that these findings are strongly dependent on the characteristics of the electrode-skin interface. In our case, we used large stimulation electrodes placed on the anterior thigh, which cause higher capacitive effects. The controllability, voltage compliance, and charge characteristics of each stimulation technique should be considered during the stimulators design. For applications that require the activation of a large amount of nerve fibers, VC is a more suitable option. In contrast, if the application requires a high controllability, then CC should be chosen prior to VC.

  8. Nonlinear Magnetoelectric Response of Planar Ferromagnetic-Piezoelectric Structures to Sub-Millisecond Magnetic Pulses

    Directory of Open Access Journals (Sweden)

    Mikhail Shamonin

    2012-11-01

    Full Text Available The magnetoelectric response of bi- and symmetric trilayer composite structures to pulsed magnetic fields is experimentally investigated in detail. The structures comprise layers of commercially available piezoelectric (lead zirconate titanate and magnetostrictive (permendur or nickel materials. The magnetic-field pulses have the form of a half-wave sine function with duration of 450 µs and amplitudes ranging from 500 Oe to 38 kOe. The time dependence of the resulting voltage is presented and explained by theoretical estimations. Appearance of voltage oscillations with frequencies much larger than the reciprocal pulse length is observed for sufficiently large amplitudes (~1–10 kOe of the magnetic-field pulse. The origin of these oscillations is the excitation of bending and planar acoustic oscillations in the structures. Dependencies of the magnetoelectric voltage coefficient on the excitation frequency and the applied magnetic field are calculated by digital signal processing and compared with those obtained by the method of harmonic field modulation. The results are of interest for developing magnetoelectric sensors of pulsed magnetic fields as well as for rapid characterization of magnetoelectric composite structures.

  9. ON APPLYING ENDPOINT EXTENSION METHOD OF LMD IN PROCESSING WRIST PULSE SIGNALS%LMD 端点延拓方法在脉象信号处理中的应用研究

    Institute of Scientific and Technical Information of China (English)

    卫佳骏; 夏春明; 周侃恒; 刘攀; 王忆勤; 燕海霞

    2016-01-01

    We applied the LMD algorithm in wrist pulse signals analyses for the first time in order to improve low computational efficiency and heavy endpoint effect that the EMD algorithm exists in pulse signals analyses.Meanwhile,for the endpoint contamination existed still,by combining the wavelet modulus maxima denoising method we proposed a matching degree-based wrist pulse signal extension method.In it the wavelet modulus maxima denoising method is applied to the signal preprocessing,solves the problems in LMD algorithm caused by noise that it is unconvergence and the signal diverges from both ends.Through verification of simulated signal and actual processing on wrist pulse signal,results showed that LMD algorithm has good decomposition effect and can more accurately reflect the characteristic information in pulse.Moreover,the proposed matching degree-based extension method for wrist pulse signal can evidently improve the end effect in LMD algorithm.%针对 EMD 方法在脉象信号分析中存在的运算效率低以及端点效应严重等问题,首次将 LMD 时频分析方法运用于脉象信号的分析。同时对于仍然存在的端点污染,结合小波模极大值去噪方法提出了一种基于匹配度的脉象信号延拓方法。其中,小波模极大值去噪方法运用于信号的预处理过程,解决 LMD 方法中原本由于噪声引起的算法不收敛,信号两端发散等问题。通过仿真信号的验证及脉象信号的实际处理,结果表明 LMD 方法具有较好的分解效果,能更准确地反映脉象信号中的特征信息,且所提出的基于匹配度的脉象信号延拓方法可以明显改善 LMD 方法中存在的端点效应。

  10. Mixed voltage VLSI design

    Science.gov (United States)

    Panwar, Ramesh; Rennels, David; Alkalaj, Leon

    1993-01-01

    A technique for minimizing the power dissipated in a Very Large Scale Integration (VLSI) chip by lowering the operating voltage without any significant penalty in the chip throughput even though low voltage operation results in slower circuits. Since the overall throughput of a VLSI chip depends on the speed of the critical path(s) in the chip, it may be possible to sustain the throughput rates attained at higher voltages by operating the circuits in the critical path(s) with a high voltage while operating the other circuits with a lower voltage to minimize the power dissipation. The interface between the gates which operate at different voltages is crucial for low power dissipation since the interface may possibly have high static current dissipation thus negating the gains of the low voltage operation. The design of a voltage level translator which does the interface between the low voltage and high voltage circuits without any significant static dissipation is presented. Then, the results of the mixed voltage design using a greedy algorithm on three chips for various operating voltages are presented.

  11. "Curing" of plasmid DNA in acetogen using microwave or applying an electric pulse improves cell growth and metabolite production as compared to the plasmid-harboring strain.

    Science.gov (United States)

    Berzin, Vel; Kiriukhin, Michael; Tyurin, Michael

    2013-03-01

    Plasmid-free acetogen Clostridium sp. MT962 electrotransformed with a small cryptic plasmid pMT351 was used to develop time- and cost-effective methods for plasmid elimination. Elimination of pMT351 restored production of acetate and ethanol to the levels of the plasmid-free strain with no dry cell weight changes. Destabilizing cell membrane via microwave at 2.45 GHz, or exposure to a single 12 ms square electric pulse at 35 kV cm⁻¹, eliminated pMT351 in 42-47 % of cells. Plasmid elimination with a single square electric pulse required 10 versus 0.1 J needed to introduce the same 3,202-bp plasmid into the cells as calculated per cell sample of Clostridium sp. MT962. Microwave caused visible changes in repPCR pattern and increased ethanol production at the expense of acetate. This is the first report on microwave of microwave ovens, wireless routers, and mobile devices causing chromosomal DNA aberrations in microbes along with carbon flux change.

  12. A Fast Multimodal Ectopic Beat Detection Method Applied for Blood Pressure Estimation Based on Pulse Wave Velocity Measurements in Wearable Sensors

    Science.gov (United States)

    Pflugradt, Maik; Geissdoerfer, Kai; Goernig, Matthias; Orglmeister, Reinhold

    2017-01-01

    Automatic detection of ectopic beats has become a thoroughly researched topic, with literature providing manifold proposals typically incorporating morphological analysis of the electrocardiogram (ECG). Although being well understood, its utilization is often neglected, especially in practical monitoring situations like online evaluation of signals acquired in wearable sensors. Continuous blood pressure estimation based on pulse wave velocity considerations is a prominent example, which depends on careful fiducial point extraction and is therefore seriously affected during periods of increased occurring extrasystoles. In the scope of this work, a novel ectopic beat discriminator with low computational complexity has been developed, which takes advantage of multimodal features derived from ECG and pulse wave relating measurements, thereby providing additional information on the underlying cardiac activity. Moreover, the blood pressure estimations’ vulnerability towards ectopic beats is closely examined on records drawn from the Physionet database as well as signals recorded in a small field study conducted in a geriatric facility for the elderly. It turns out that a reliable extrasystole identification is essential to unsupervised blood pressure estimation, having a significant impact on the overall accuracy. The proposed method further convinces by its applicability to battery driven hardware systems with limited processing power and is a favorable choice when access to multimodal signal features is given anyway. PMID:28098831

  13. Pulsed corona discharge at atmospheric and supercritical conditions

    Science.gov (United States)

    Lock, Evgeniya Hristova

    Pulsed corona discharge is one of the non-equilibrium plasma techniques, by which electrical power is mainly utilized to generate high-energy electrons. These react further with the background gas to produce radicals, which can be further employed in chemically selective reactions. Study of the initiation of pulsed corona discharge in carbon dioxide and air was conducted. Furthermore due to its high removal efficiency, energy yields and good economy, the pulsed corona discharge was employed for removal of methanol and dimethyl sulfide. These compounds are part of the volatile organic compounds (VOC) air pollutants, which are subject of severe environmental regulations due to their toxicity, environmental persistence and intensity of smell. The study provides experimental data for the destruction of methanol and dimethyl sulfide from dry and humid air streams. The effects of the process parameters, including applied voltage, pulse repetition rate, initial concentration of pollutants, temperature and humidity on the destruction and removal efficiency and energy cost are analyzed. Specific consideration is given to the formation of unwanted byproducts. The study on plasma application for pollution control showed that small amounts of dispersed liquid droplets increase the efficiency of the chemical utilization of the high-energy electrons and reduce the required power. So media that could facilitate homogeneous and heterogeneous chemistry at the same time would enhance the efficiency of the removal process. Such medium that has properties intermediate between the gas and liquid phase is the supercritical fluid. Generation of plasma in supercritical fluids is an unexplored area in plasma science. The generation of plasma at elevated pressures usually requires high voltages or small interelectrode distances. The supercritical phase is characterized by extensive cluster formation in the vicinity of the critical point. Typically the clusters have lower ionization

  14. Scaling Up the Pulse-Remagnetization Experiment for Large Animals

    Science.gov (United States)

    Kirschvink, J. L.; Hilburn, I. A.; Golash, H. N.; Wang, C. X.; Wu, D. A.; Mizuhara, Y.; Shimojo, S.; Matani, A.

    2016-12-01

    Pulse-remagnetization has been a commonly-used technique in rock magnetic studies for producing IRM curves for the past 33 years. Typical circuits involve charging a bank of capacitors to a desired voltage, and then discharging it on command through a silicon-controlled rectifier into a solenoid magnet coil. Back-oscillations are prevented by dissipating the energy with a suitably-configured diode, and the intensity of the single magnetic peak resulting from this procedure is proportional to the charging voltage. However, this technique also has been applied many times in biology to measure the coercivity spectrum of various populations of magnetoctactic bacteria, as well as in successful tests of the hypothesis that biological magnetite is the biophysical transducer for magnetic field sensitivity (magnetoreception) in animals. We have recently discovered earth-strength magnetic effects on the brainwave patterns of a large mammal. Experimental results indicate that the effects are not a result of either electrical induction or an axially-symmetric biophysical compass; therefore, the most likely explanation is a polar compass provided by specialized sensory cells containing chains of single-domain biological magnetite. If so, we should be able to invert the magnetic polarity of this response via a properly-configured pulse-remagnetization experiment, and thereby place constraints on the microscopic coercivity of the magnetite crystals in the hypothesized receptor cells. To achieve this end, we have constructed a large-volume IRM coil capable of producing a uniform magnetic field pulse of up to 70 mT over the volume of the target animal's head, while also applying a co-axial 1 mT static DC biasing field. Applying a DC-biased IRM pulse to our animal subjects has proven to be surprisingly difficult, both due to the complexity of engineering a coaxial pulse and biasing coil system of this volume, and also due to the care and safety protocols necessary to ensure the well

  15. Excitation of voltage oscillations in an induction voltage adder

    Directory of Open Access Journals (Sweden)

    Nichelle Bruner

    2009-07-01

    Full Text Available The induction voltage adder is an accelerator architecture used in recent designs of pulsed-power driven x-ray radiographic systems such as Sandia National Laboratories’ Radiographic Integrated Test Stand (RITS, the Atomic Weapons Establishment’s planned Hydrus Facility, and the Naval Research Laboratory’s Mercury. Each of these designs relies on magnetic insulation to prevent electron loss across the anode-cathode gap in the vicinity of the adder as well as in the coaxial transmission line. Particle-in-cell simulations of the RITS adder and transmission line show that, as magnetic insulation is being established during a pulse, some electron loss occurs across the gap. Sufficient delay in the cavity pulse timings provides an opportunity for high-momentum electrons to deeply penetrate the cavities of the adder cells where they can excite radio-frequency resonances. These oscillations may be amplified in subsequent gaps, resulting in oscillations in the output power. The specific modes supported by the RITS-6 accelerator and details of the mechanism by which they are excited are presented in this paper.

  16. Resistor divider for high voltage pulse measurement in vacuum%一种在真空中测量脉冲高电压的电阻分压器

    Institute of Scientific and Technical Information of China (English)

    卫兵; 关永超; 卿燕玲; 陈林; 周良骥; 李晔; 丰树平

    2012-01-01

    A resistor divider has been designed for voltage measurement of diode load for 1 MV/100 kA fast linear transformer driver(LTD). The divider is designed with two stages. The primary stage is a column of alternating annular metal grading rings and tapered insulators enclosing a resistive solution of sodium thiosulfate. A middle electrode is connected to the secondary voltage dividing stage. There is a 4 kΩ resistor in series with the 50 Ω input impedance of the attenuator or oscilloscope. The e-quivalent circuit of the divider which includes distributed capacitance and inductance has been calculated. It indicates that the high frequency limit of the divider is about 200 MHz. The divider has been calibrated in-situ using a P6015A probe and a high voltage pulser. The calibration ratio is 5 400 : 1. The voltage of diode load reaches 1. 08 MV when the charging voltage of LTD stage is ±85 kV respectively, according with the simulation of LTD.%为测量快脉冲直线变压器驱动源(LTD)二极管负载的脉冲高电压,设计了在真空环境中使用的电阻分压器.分压器使用绝缘堆结构,采用静电场模拟分析了分压器的电场分布.建立了包含分布参数的等效电路,并进行了频率响应仿真,可得分压器的频响上限为200 MHz.使用标准高压探头对分压器进行在线标定,分压比标定结果为5 400∶1,与设计值相符合.在LTD调试实验中,模块充电85 kV时二极管电压为1.08 MV,与理论估算结果一致.

  17. A modularized pulse forming line using glass-ceramic slabs.

    Science.gov (United States)

    Wang, Songsong; Shu, Ting; Yang, Hanwu

    2012-08-01

    In our lab, a kind of glass-ceramic slab has been chosen to study the issues of applying solid-state dielectrics to pulse forming lines (PFLs). Limited by the manufacture of the glass-ceramic bulk with large sizes, a single ceramic slab is hard to store sufficient power for the PFL. Therefore, a modularized PFL design concept is proposed in this paper. We regard a single ceramic slab as a module to form each single Blumlein PFL. We connect ceramic slabs in series to enlarge pulse width, and stack the ceramic Blumlein PFLs in parallel to increase the output voltage amplitude. Testing results of a single Blumlein PFL indicate that one ceramic slab contributes about 11 ns to the total pulse width which has a linear relation to the number of the ceramic slabs. We have developed a prototype facility of the 2-stage stacked Blumlein PFL with a length of 2 ceramic slabs. The PFL is dc charged up to 5 kV, and the output voltage pulse of 10 kV, 22 ns is measured across an 8 Ω load. Simulation and experiment results in good agreement demonstrate that the modularized design is reasonable.

  18. High voltage switch triggered by a laser-photocathode subsystem

    Science.gov (United States)

    Chen, Ping; Lundquist, Martin L.; Yu, David U. L.

    2013-01-08

    A spark gap switch for controlling the output of a high voltage pulse from a high voltage source, for example, a capacitor bank or a pulse forming network, to an external load such as a high gradient electron gun, laser, pulsed power accelerator or wide band radar. The combination of a UV laser and a high vacuum quartz cell, in which a photocathode and an anode are installed, is utilized as triggering devices to switch the spark gap from a non-conducting state to a conducting state with low delay and low jitter.

  19. Neutral-point voltage dynamic model of three-level NPC inverter for reactive load

    DEFF Research Database (Denmark)

    Maheshwari, Ram Krishan; Munk-Nielsen, Stig; Busquets-Monge, Sergio

    2012-01-01

    A three-level neutral-point-clamped inverter needs a controller for the neutral-point voltage. Typically, the controller design is based on a dynamic model. The dynamic model of the neutral-point voltage depends on the pulse width modulation technique used for the inverter. A pulse width modulati...

  20. Research on Topologies of Voltage Balancers Applied in DC Micro-grid%面向直流微电网的电压平衡器拓扑结构研究

    Institute of Scientific and Technical Information of China (English)

    汪飞; 雷志方; 徐新蔚

    2016-01-01

    As an energy-saving efficient DC distribution form, bipolar DC bus has a great advantage in the low voltage DC power system, in which the voltage balancer plays an important role. A voltage balancer, on the one hand, achieves a conversion from unipolar bus to bipolar bus, and it also solves the problem of power imbalance between positive and negative polarity bus. This paper analyzed the existing research results of voltage balancer topologies in detail, and summed up the method of forming voltage balancers. Furthermore, new topologies were proposed, such as Cuk, Super-Sepic/Zeta and interleaved Buck/Boost type voltage balancers. Finally, the correctness of the proposed topologies were verified by simulations, and two phase interleaved Buck/Boost type voltage balancer experimental platform was used to verify its good bipolar bus distribution effect and the fine current sharing and dynamic characteristic of interleaved average current control strategy.%作为一种节能高效的直流配电形式,双极性直流母线配电在低压直流配电系统中具有较大的应用优势,电压平衡器在其中扮演着重要的角色。电压平衡器一方面实现了单极性配电向双极性配电的转化,另一方面也解决了正负极性母线间的功率不平衡问题。该文首先分析了现有的电压平衡器拓扑结构研究成果;然后归纳出了电压平衡器的形成方法,提出了Cuk型电压平衡器、Super-Sepic/Zeta型电压平衡器和交错并联 Buck/Boost 型电压平衡器;最后通过仿真验证了所提出拓扑结构的正确性,通过两相交错并联Buck/Boost型电压平衡器实验平台验证了所提出的交错采样交错平均电流控制策略良好的均流效果和动态响应速度以及平衡器优异的双极性母线配电效果。

  1. Double discharges in unipolar-pulsed dielectric barrier discharge xenon excimer lamps

    Science.gov (United States)

    Liu, Shuhai; Neiger, Manfred

    2003-07-01

    Excitation of dielectric barrier discharge xenon excimer lamps by unipolar short square pulses is studied in this paper. Two discharges with different polarity are excited by each voltage pulse (double discharge phenomenon). The primary discharge occurs at the top or at the rising flank of the applied unipolar square pulse, which is directly energized by the external circuit. The secondary discharge with the reversed polarity occurs at the falling flank or shortly after the falling flank end (zero external voltage) depending on the pulse width, which is energized by the energy stored by memory charges deposited by the primary discharge. Fast-speed ICCD imaging shows the primary discharge has a conic discharge appearance with a channel broadening on the anode side. This channel broadening increases with increasing the pulse top level. Only the anode-side surface discharge is observed in the primary discharge. The surface discharge on the cathode side which is present in bipolar sine voltage excitation is not observed. On the contrary, the secondary discharge has only the cathode-side surface discharge. The surface discharge on the anode side is not observed. The secondary discharge is much more diffuse than the primary discharge. Time-resolved emission measurement of double discharges show the secondary discharge emits more VUV xenon excimer radiation but less infrared (IR) xenon atomic emission than the primary discharge. It was found that the IR xenon atomic emission from the secondary discharge can be reduced by shortening the pulse width. The energy efficiency of unipolar-pulsed xenon excimer lamps (the overall energy efficiency of double discharges) is much higher than that obtained under bipolar sine wave excitation. The output VUV spectrum under unipolar pulse excitation is found to be identical to that under sine wave excitation and independent of injected electric power.

  2. Characterisation of the VELO High Voltage System

    CERN Document Server

    Rakotomiaramanana, B; Eklund, L

    2008-01-01

    The high voltage system supplies the bias voltage to the 88 silicon sensors which comprise the LHCb Vertex Locator (VELO). This note describes the results of the tests which have been performed on the hardware of the high voltage system of the VELO. Each individual test detailed in this note corresponds to a specific requirement of the system. These requirements arise primarily from ensuring the safety of the silicon sensors and the quality of the data taken from the VELO modules. The tests performed are in four categories: normal operation of the high voltage system; vercation of its stability under operation; discussion of its behaviour in failure modes; and details of operation at low voltage. Noteworthy issues, identified through the tests, include the behaviour of the high voltage modules at voltages below 9V, the current limit that can be applied during ramping of the voltage, and the speed with which the voltage is cut during failures of the system. The results of these tests provide high confidence th...

  3. Characterisation of the VELO High Voltage System

    CERN Document Server

    Rakotomiaramanana, B; Parkes, C; Eklund, L

    2008-01-01

    The high voltage system supplies the bias voltage to the 88 silicon sensors which comprise the LHCb Vertex Locator (VELO). This note describes the results of the tests which have been performed on the hardware of the high voltage system of the VELO. Each individual test detailed in this note corresponds to a specific requirement of the system. These requirements arise primarily from ensuring the safety of the silicon sensors and the quality of the data taken from the VELO modules. The tests performed are in four categories: normal operation of the high voltage system; verification of its stability under operation; discussion of its behaviour in failure modes; and details of operation at low voltage. Noteworthy issues, identified through the tests, include the behaviour of the high voltage modules at voltages below 9V, the current limit that can be applied during ramping of the voltage, and the speed with which the voltage is cut during failures of the system. The results of these tests provide high confidence...

  4. Pulsed electron source characterization with the modified three gradient method

    CERN Document Server

    Marghitu, S; Dinca, C; Marghitu, O

    2001-01-01

    Results from the Modified Three Gradient Method (MTGM), applied to a pulsed high intensity electron source, are presented. The MTGM makes possible the non-destructive determination of beam emittance in the space charge presence [1]. We apply the MTGM to an experimental system equipped with a Pierce convergent diode, working in pulse mode, and having a directly heated cathode as electron source. This choice was mainly motivated by the availability of an analytical characterization of this source type [2], as well as the extended use of the Pierce type sources in linear accelerators. The experimental data are processed with a numerical matching program, based on the K-V equation for an axially symmetric configuration [3], to determine the emittance and object cross-over position and diameter. The variation of these parameters is further investigated with respect to both electrical and constructive characteristics of the source: cathode heating current, extraction voltage, and cathode-anode distance.

  5. The use of pulsed amperometry combined with ion-exclusion chromatography for the simultaneous analysis of ascorbic acid and sulfite.

    Science.gov (United States)

    Wagner, H P; McGarrity, M J

    1991-06-21

    Initial attempts to monitor ascorbic acid and sulfite, in a beer matrix, by combining ion-exclusion chromatography with a pulsed amperometric detector using a single applied voltage to the platinum working electrode, were unsuccessful. Alternatively, good chromatograms for the separation of the two antioxidants were achieved utilizing a standard, amperometric cell. However, remarkably superior results were observed when this standard cell was operated in a pulsed mode and cleaning cycles were continually applied throughout the analysis. The working electrode stability and precision have been examined. Preliminary spike recovery data indicate acceptable accuracy for the method. Comparisons of this method to standard reference methods are currently ongoing.

  6. Effects of various concentrations of diethylcarbamazine citrate applied as eye drops in ocular onchocerciasis, and the possibilities of improved therapy from continuous non-pulsed delivery.

    Science.gov (United States)

    Jones, B R; Anderson, J; Fuglsang, H

    1978-01-01

    Diethylcarbamazine was given as eye drops in varying concentrations in a half-log dilution series from 1.0 to 0.0001% to patients with ocular onchocerciasis. Migration of microfilariae into the cornea, followed by their straightening and disintegration, was observed with delivery rates as low as 0.1 microgram/hour. Dose-related adverse inflammatory reactions, including the development of globular limbal infiltrates with itching and redness, were seen with delivery rates as low as 0.6 microgram/hour, but substantial inflammatory reactions, including severe vasculitis, were seen only with delivery rates of or above 1.0 microgram/hour. This suggests that it should be possible to achieve beneficial clearing of the microfilarial load, without adverse reactions, by continuous non-pulsed delivery of the drug. Technology exists for such delivery, either directly into the eye or systemically by a transdermal system that could give 3 to 7 days' treatment from each application. The observations reported suggest that after preliminary clearing of the microfilarial load by carefully controlled delivery of DEC it may be possible to maintain therapy by less strictly controlled delivery in DEC-medicated salt, or to use treatment with suramin, without incurring substantial adverse reactions, such as a deterioration in vision in cases in which the optic nerve is already compromised. Continuous non-pulsed DEC delivery systems could have a place in the management of onchocercal sclerosing keratitis. The unique opportunities for using the ocular model to define the requirements for beneficial non-damaging therapy with DEC should be explored in further field trials. Images PMID:678494

  7. Effects of various concentrations of diethylcarbamazine citrate applied as eye drops in ocular onchocerciasis, and the possibilities of improved therapy from continuous non-pulsed delivery.

    Science.gov (United States)

    Jones, B R; Anderson, J; Fuglsang, H

    1978-07-01

    Diethylcarbamazine was given as eye drops in varying concentrations in a half-log dilution series from 1.0 to 0.0001% to patients with ocular onchocerciasis. Migration of microfilariae into the cornea, followed by their straightening and disintegration, was observed with delivery rates as low as 0.1 microgram/hour. Dose-related adverse inflammatory reactions, including the development of globular limbal infiltrates with itching and redness, were seen with delivery rates as low as 0.6 microgram/hour, but substantial inflammatory reactions, including severe vasculitis, were seen only with delivery rates of or above 1.0 microgram/hour. This suggests that it should be possible to achieve beneficial clearing of the microfilarial load, without adverse reactions, by continuous non-pulsed delivery of the drug. Technology exists for such delivery, either directly into the eye or systemically by a transdermal system that could give 3 to 7 days' treatment from each application. The observations reported suggest that after preliminary clearing of the microfilarial load by carefully controlled delivery of DEC it may be possible to maintain therapy by less strictly controlled delivery in DEC-medicated salt, or to use treatment with suramin, without incurring substantial adverse reactions, such as a deterioration in vision in cases in which the optic nerve is already compromised. Continuous non-pulsed DEC delivery systems could have a place in the management of onchocercal sclerosing keratitis. The unique opportunities for using the ocular model to define the requirements for beneficial non-damaging therapy with DEC should be explored in further field trials.

  8. Ion current extracted from a self ignition plasma around the target immersed in a pulsed rf ICP methane plasma

    Science.gov (United States)

    Tanaka, Takeshi; Watanabe, Satoshi; Mizuno, Giichiro; Takagi, Toshinori; Yoshida, Mitsuhiro; Horibe, Hiroshi; Yukimura, Ken

    2003-05-01

    When a pulsed voltage is applied to a target immersed in plasma, the surrounding medium of the target is self-ignited under an appropriate discharge condition. For a three-dimensional substrate, ion implantation and deposition of the plasma species are promising to be uniformly attained by the self-ignition plasma. A retained dose of conformal ion implantation may increase with the self-ignition plasma generated in the target-immersed plasma. Ion are extracted from both the target-immersed plasma and the self-ignition plasma. In this research, a stainless steel target with a diameter of 140 mm and a thickness of 18 mm was immersed in a pulsed inductively coupled methane plasma to which a pulse voltage of -400 V to -10 kV with a width of 12 μs was repeatedly applied. The self-ignition plasma was generated at the voltage higher than about -1.2 kV. It was found that the shape of the current waveform changes by varying the applied voltage due to the change of the current from the self-ignition plasma.

  9. Hybrid zero-voltage switching (ZVS) control for power inverters

    Science.gov (United States)

    Amirahmadi, Ahmadreza; Hu, Haibing; Batarseh, Issa

    2016-11-01

    A power inverter combination includes a half-bridge power inverter including first and second semiconductor power switches receiving input power having an intermediate node therebetween providing an inductor current through an inductor. A controller includes input comparison circuitry receiving the inductor current having outputs coupled to first inputs of pulse width modulation (PWM) generation circuitry, and a predictive control block having an output coupled to second inputs of the PWM generation circuitry. The predictive control block is coupled to receive a measure of Vin and an output voltage at a grid connection point. A memory stores a current control algorithm configured for resetting a PWM period for a switching signal applied to control nodes of the first and second power switch whenever the inductor current reaches a predetermined upper limit or a predetermined lower limit.

  10. Implementation of Dynamic Voltage Restorer for Mitigation of Voltage Sag

    Directory of Open Access Journals (Sweden)

    K.Vinod Kumar

    2013-07-01

    Full Text Available Power quality is one of major concerns in the present. It has become important, especially with the introduction of sophisticated devices, whose performance is very sensitive to the quality of power supply. The dynamic voltage restorer (DVR is one of the modern devices used in distribution systems to improve the power quality. In this paper, emergency control in distribution systems is discussed by using the proposed multifunctional DVR control strategy.Also, themultiloop controller using the Posicast and P+Resonant controllers is proposed in order to improve the transient response and eliminate the steady state error in DVR response,respectively.The proposed process is applied to some riots in load voltage effected by induction motors starting, and a three-phase short circuit fault. The three-phase short circuits, and the large induction motors are suddenly started then voltage sags areoccurred.The innovation here is that by using the Multifunctional Dynamic Voltage Restorer, improve the power quality in distribution side. Simulation results show the capability of the DVR to control the emergency conditions of the distribution systems by using MATLAB/Simulink software.

  11. Comparative study of electrical breakdown properties of deionized water and heavy water under pulsed power conditions

    Energy Technology Data Exchange (ETDEWEB)

    Veda Prakash, G.; Kumar, R.; Saurabh, K.; Nasir,; Anitha, V. P.; Chowdhuri, M. B.; Shyam, A. [Institute for Plasma Research, Bhat, Gandhinagar 382428 (India)

    2016-01-15

    A comparative study of electrical breakdown properties of deionized water (H{sub 2}O) and heavy water (D{sub 2}O) is presented with two different electrode materials (stainless steel (SS) and brass) and polarity (positive and negative) combinations. The pulsed (∼a few tens of nanoseconds) discharges are conducted by applying high voltage (∼a few hundred kV) pulse between two hemisphere electrodes of the same material, spaced 3 mm apart, at room temperature (∼26-28 °C) with the help of Tesla based pulse generator. It is observed that breakdown occurred in heavy water at lesser voltage and in short duration compared to deionized water irrespective of the electrode material and applied voltage polarity chosen. SS electrodes are seen to perform better in terms of the voltage withstanding capacity of the liquid dielectric as compared to brass electrodes. Further, discharges with negative polarity are found to give slightly enhanced discharge breakdown voltage when compared with those with positive polarity. The observations corroborate well with conductivity measurements carried out on original and post-treated liquid samples. An interpretation of the observations is attempted using Fourier transform infrared measurements on original and post-treated liquids as well as in situ emission spectra studies. A yet another important observation from the emission spectra has been that even short (nanosecond) duration discharges result in the formation of a considerable amount of ions injected into the liquid from the electrodes in a similar manner as reported for long (microseconds) discharges. The experimental observations show that deionised water is better suited for high voltage applications and also offer a comparison of the discharge behaviour with different electrodes and polarities.

  12. High Bandwidth Zero Voltage Injection Method for Sensorless Control of PMSM

    DEFF Research Database (Denmark)

    Ge, Xie; Lu, Kaiyuan; Kumar, Dwivedi Sanjeet

    2014-01-01

    High frequency signal injection is widely used in PMSM sensorless control system for low speed operations. The conventional voltage injection method often needs filters to obtain particular harmonic component in order to estimate the rotor position; or it requires several voltage pulses to be inj...... in a fast current regulation performance. Injection of zero voltage also minimizes the inverter voltage error effects caused by the dead-time.......High frequency signal injection is widely used in PMSM sensorless control system for low speed operations. The conventional voltage injection method often needs filters to obtain particular harmonic component in order to estimate the rotor position; or it requires several voltage pulses...... to be injected before the position may be estimated. In this paper, a single pulse zero voltage injection method is proposed. The rotor position is directly estimated from the current ripple at half of the switching frequency. No machine parameters are needed and using of filters is avoided. This results...

  13. SNMR pulse sequence phase cycling

    Science.gov (United States)

    Walsh, David O; Grunewald, Elliot D

    2013-11-12

    Technologies applicable to SNMR pulse sequence phase cycling are disclosed, including SNMR acquisition apparatus and methods, SNMR processing apparatus and methods, and combinations thereof. SNMR acquisition may include transmitting two or more SNMR pulse sequences and applying a phase shift to a pulse in at least one of the pulse sequences, according to any of a variety cycling techniques. SNMR processing may include combining SNMR from a plurality of pulse sequences comprising pulses of different phases, so that desired signals are preserved and indesired signals are canceled.

  14. Mitigation Voltage Sag in Power System by Static Synchronous Compensator

    Directory of Open Access Journals (Sweden)

    Prechanon Kumkratug

    2010-01-01

    Full Text Available Problem statement: The disturbance in power system is unavoidable situation. It cause in voltage sag in power system. Approach: This study applied the STATCOM to mitigate voltage of the system. The mathematical model of power system equipped with a STATCOM is systematically derived. The presented mathematical model is shown how it effects on voltage sag improvement. The simulation results are tested on a Single Machine Infinite bus. The proposed method is equipped in sample system with severe disturbance. The variation voltage of the system without and with a STATCOM is plotted and compared. Results: It was found that the system without a STATCOM has high voltage variation especially voltage sags whereas with a STATCOM the system voltage has small voltage sages. Conclusion: From the simulation results, the STATCOM can mitigate voltage of power system.

  15. Discharge pulse phenomenology

    Science.gov (United States)

    Frederickson, A. R.

    1985-01-01

    A model was developed which places radiation induced discharge pulse results into a unified conceptual framework. Only two phenomena are required to interpret all space and laboratory results: (1) radiation produces large electrostatic fields inside insulators via the trapping of a net space charge density; and (2) the electrostatic fields initiate discharge streamer plasmas similar to those investigated in high voltage electrical insulation materials; these streamer plasmas generate the pulsing phenomena. The apparent variability and diversity of results seen is an inherent feature of the plasma streamer mechanism acting in the electric fields which is created by irradiation of the dielectrics. The implications of the model are extensive and lead to constraints over what can be done about spacecraft pulsing.

  16. Capacitance of High-Voltage Coaxial Cable in Plasma Immersion Ion Implantation

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    Plasma immersion ion implantation (PIII) is an excellent technique for the surface modification of complex-shaped components. Owing to pulsed operation mode of the high voltage and large slew rate, the capacitance on the high-voltage coaxial cable can be detrimental to the processand cannot be ignored. In fact, a significant portion of the rise-time/fall-time of the implantation voltage pulse and big initial current can be attributed to the coaxial cable.

  17. Development of 600 kV triple resonance pulse transformer.

    Science.gov (United States)

    Li, Mingjia; Zhang, Faqiang; Liang, Chuan; Xu, Zhou

    2015-06-01

    In this paper, a triple-resonance pulse transformer based on an air-core transformer is introduced. The voltage across the high-voltage winding of the air-core transformer is significantly less than the output voltage; instead, the full output voltage appears across the tuning inductor. The maximum ratio of peak load voltage to peak transformer voltage is 2.77 in theory. By analyzing pulse transformer's lossless circuit, the analytical expression for the output voltage and the characteristic equation of the triple-resonance circuit are presented. Design method for the triple-resonance pulse transformer (iterated simulation method) is presented, and a triple-resonance pulse transformer is developed based on the existing air-core transformer. The experimental results indicate that the maximum ratio of peak voltage across the load to peak voltage across the high-voltage winding of the air-core transformer is approximately 2.0 and the peak output voltage of the triple-resonance pulse transformer is approximately 600 kV.

  18. 2.3-MW Medium-Voltage, Three-Level Wind Energy Inverter Applying a Unique Bus Structure and 4.5-kV Si/SiC Hybrid Isolated Power Modules: Preprint

    Energy Technology Data Exchange (ETDEWEB)

    Erdman, W.; Keller, J.; Grider, D.; VanBrunt, E.

    2014-11-01

    A high-efficiency, 2.3-MW, medium-voltage, three-level inverter utilizing 4.5-kV Si/SiC (silicon carbide) hybrid modules for wind energy applications is discussed. The inverter addresses recent trends in siting the inverter within the base of multimegawatt turbine towers. A simplified split, three-layer laminated bus structure that maintains low parasitic inductances is introduced along with a low-voltage, high-current test method for determining these inductances. Feed-thru bushings, edge fill methods, and other design features of the laminated bus structure provide voltage isolation that is consistent with the 10.4-kV module isolation levels. Inverter efficiency improvement is a result of the (essential) elimination of the reverse recovery charge present in 4.5-kV Si PIN diodes, which can produce a significant reduction in diode turn-off losses as well as insulated-gate bipolar transistor (IGBT) turn-on losses. The hybrid modules are supplied in industry-standard 140 mm x 130 mm and 190 mm x 130 mm packages to demonstrate direct module substitution into existing inverter designs. A focus on laminated bus/capacitor-bank/module subassembly level switching performance is presented.

  19. Technological Aspects: High Voltage

    CERN Document Server

    Faircloth, D C

    2013-01-01

    This paper covers the theory and technological aspects of high-voltage design for ion sources. Electric field strengths are critical to understanding high-voltage breakdown. The equations governing electric fields and the techniques to solve them are discussed. The fundamental physics of high-voltage breakdown and electrical discharges are outlined. Different types of electrical discharges are catalogued and their behaviour in environments ranging from air to vacuum are detailed. The importance of surfaces is discussed. The principles of designing electrodes and insulators are introduced. The use of high-voltage platforms and their relation to system design are discussed. The use of commercially available high-voltage technology such as connectors, feedthroughs and cables are considered. Different power supply technologies and their procurement are briefly outlined. High-voltage safety, electric shocks and system design rules are covered.

  20. Experimental study of polarity dependence in repetitive nanosecond-pulse breakdown

    Institute of Scientific and Technical Information of China (English)

    Shao Tao; Sun Guang-Sheng; Yan Ping; Wang Jue; Yuan Wei-Qun; Zhang Shi-Chang

    2007-01-01

    Pulsed breakdown of dry air at ambient pressure has been investigated in the point-plane geometry,using repetitive nanosecond pulses with 10 ns risetime,20-30 as duration,and up to 100 kV amplitude.A major concern in this paper is to study the dependence of breakdown strength on the point-electrode polarity.Applied voltage,breakdown current and repetitive stressing time are measured under the experimental conditions of some variables including pulse voltage peak,gap spacing and repetition rate.The results show that increasing the E-field strength can decrease breakdown time lag,repetitive stressing time and the number of applied pulses as expected.However,compared with the traditional polarity dependence it is weakened and not significant in the repetitive nanosecond-pulse breakdown.The ambiguous polaxity dependence in the experimental study is involved with an accumulation effect of residual charges and metastable states.Moreover,it is suggested that the reactions associated with the detachment of negative ions and impact deactivation of metastable specms could provide a source of primary initiating electrons for breakdown.

  1. Particle-in-cell simulation of Trichel pulses in pure oxygen

    Energy Technology Data Exchange (ETDEWEB)

    Soria-Hoyo, C [Dpto. Electronica y Electromagnetismo, Universidad de Sevilla, Avda. Reina Mercedes s/n, Sevilla 41012 (Spain); Pontiga, F [Dpto. Fisica Aplicada II, Universidad de Sevilla, Avda. Reina Mercedes s/n, Sevilla 41012 (Spain); Castellanos, A [Dpto. Electronica y Electromagnetismo, Universidad de Sevilla, Avda. Reina Mercedes s/n, Sevilla 41012 (Spain)

    2007-08-07

    The development and propagation of Trichel pulses in oxygen have been numerically simulated using an improved fluid particle-in-cell (PIC) method. The numerical method has been optimized to accurately reproduce sequences of about 100 Trichel pulses ({approx}1 ms). A classical one-dimensional model of negative corona in sphere-to-plane geometry has been used to formulate the continuity equations for electrons and ions. The effects of ionization, attachment and secondary-electron emission from the cathode have all been considered. The electric field has been obtained from the solution of Poisson's equation in two dimensions. Using this model, the temporal and electrical characteristics of Trichel pulses have been investigated, in particular, the relation between applied voltage, pulse frequency and time-averaged current intensity and charge.

  2. The possibility of multi-layer nanofabrication via atomic force microscope-based pulse electrochemical nanopatterning.

    Science.gov (United States)

    Kim, Uksu; Morita, Noboru; Lee, Deug; Jun, Martin; Park, Jeong Woo

    2017-03-27

    Pulse electrochemical nanopatterning (PECN), a non-contact scanning probe lithography (NC-SPL) process using ultrashort voltage pulses, is based primarily on an electrochemical machining (ECM) process using localized electrochemical oxidation between a sharp tool tip and the sample surface. In this study, nanoscale oxide patterns were formed on silicon Si (100) wafer surfaces via electrochemical surface nanopatterning, by supplying external pulsed currents through non-contact atomic force microscopy. Nanoscale oxide width and height were controlled by modulating the applied pulse duration. Additionally, protruding nanoscale oxides were removed completely by simple chemical etching, showing a depressed pattern on the sample substrate surface. Nanoscale two-dimensional oxides, prepared by a localized electrochemical reaction, can be defined easily by controlling physical and electrical variables, before proceeding further to a layer-by-layer nanofabrication process.

  3. Non-destructive detection of corrosion applied to steel and galvanized steel coated with organic paints by the pulsed phase thermography

    Energy Technology Data Exchange (ETDEWEB)

    Schoenberger, A.; Giese, V. [BMW AG, Munich (Germany); Virtanen, S. [Department of Materials Science, WW4-LKO, University of Erlangen-Nuremberg, Erlangen (Germany); Schroettner, H. [Centre for Electron Microscopy Graz (ZFE), Graz (Austria); Spiessberger, C. [Edevis GmbH, Stuttgart (Germany)

    2012-03-15

    Organic coatings in the automobile industry have to resist corrosion and mechanical damage from stone chipping. Currently, no tool is established in industrial non-destructive applications for analyzing the damage of stone-impacts and the following corrosion after accelerated corrosion tests. Measurement methods such as the scanning Kelvin probe can analyze the corrosion progress in a detailed manner, but with a long measurement time. The pulsed phase thermography (PPT) is a non-destructive tool to analyze inhomogeneities and defects in materials, with a huge field of applications existing. The present work shows advances in using the PPT to detect propagation of corrosion under coatings. Physical principles of the mechanism of the corrosion detection under coatings are described. Results of measurements of organic coatings on carbon steel as well as of organic coated galvanized steel show the corrosion propagation. Influencing factors to the measurement such as the thickness of the coatings are investigated, but no significant effect on the quality of the analysis was found. The corrosion progress can be monitored by the PPT fast and reliably. The achieved results correlate with the theoretical basis and the test results after surface characterization and destructive analysis of samples. (Copyright copyright 2012 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  4. Solidification of Al Alloys Under Electromagnetic Pulses and Characterization of the 3D Microstructures Using Synchrotron X-ray Tomography

    Science.gov (United States)

    Manuwong, Theerapatt; Zhang, Wei; Kazinczi, Peter Lobo; Bodey, Andrew J.; Rau, Christoph; Mi, Jiawei

    2015-07-01

    A novel programmable electromagnetic pulse device was developed and used to study the solidification of Al-15 pct Cu and Al-35 pct Cu alloys. The pulsed magnetic fluxes and Lorentz forces generated inside the solidifying melts were simulated using finite element methods, and their effects on the solidification microstructures were characterized using electron microscopy and synchrotron X-ray tomography. Using a discharging voltage of 120 V, a pulsed magnetic field with the peak Lorentz force of ~1.6 N was generated inside the solidifying Al-Cu melts which were showed sufficiently enough to disrupt the growth of the primary Al dendrites and the Al2Cu intermetallic phases. The microstructures exhibit a strong correlation to the characteristics of the applied pulse, forming a periodical pattern that resonates the frequency of the applied electromagnetic field.

  5. Stray voltage mitigation

    Energy Technology Data Exchange (ETDEWEB)

    Jamali, B.; Piercy, R.; Dick, P. [Kinetrics Inc., Toronto, ON (Canada). Transmission and Distribution Technologies

    2008-04-09

    This report discussed issues related to farm stray voltage and evaluated mitigation strategies and costs for limiting voltage to farms. A 3-phase, 3-wire system with no neutral ground was used throughout North America before the 1930s. Transformers were connected phase to phase without any electrical connection between the primary and secondary sides of the transformers. Distribution voltage levels were then increased and multi-grounded neutral wires were added. The earth now forms a parallel return path for the neutral current that allows part of the neutral current to flow continuously through the earth. The arrangement is responsible for causing stray voltage. Stray voltage causes uneven milk production, increased incidences of mastitis, and can create a reluctance to drink water amongst cows when stray voltages are present. Off-farm sources of stray voltage include phase unbalances, undersized neutral wire, and high resistance splices on the neutral wire. Mitigation strategies for reducing stray voltage include phase balancing; conversion from single to 3-phase; increasing distribution voltage levels, and changing pole configurations. 22 refs., 5 tabs., 13 figs.

  6. High voltage engineering

    CERN Document Server

    Rizk, Farouk AM

    2014-01-01

    Inspired by a new revival of worldwide interest in extra-high-voltage (EHV) and ultra-high-voltage (UHV) transmission, High Voltage Engineering merges the latest research with the extensive experience of the best in the field to deliver a comprehensive treatment of electrical insulation systems for the next generation of utility engineers and electric power professionals. The book offers extensive coverage of the physical basis of high-voltage engineering, from insulation stress and strength to lightning attachment and protection and beyond. Presenting information critical to the design, selec

  7. High voltage test techniques

    CERN Document Server

    Kind, Dieter

    2001-01-01

    The second edition of High Voltage Test Techniques has been completely revised. The present revision takes into account the latest international developments in High Voltage and Measurement technology, making it an essential reference for engineers in the testing field.High Voltage Technology belongs to the traditional area of Electrical Engineering. However, this is not to say that the area has stood still. New insulating materials, computing methods and voltage levels repeatedly pose new problems or open up methods of solution; electromagnetic compatibility (EMC) or components and systems al

  8. Mitigation of Unbalanced Voltage Sags and Voltage Unbalance in CIGRE Low Voltage Distribution Network

    OpenAIRE

    Mustafa, Ghullam; Bak-Jensen, Birgitte; Mahat, Pukar; Cecati, Carlo

    2013-01-01

    Any problem with voltage in a power network is undesirable as it aggravates the quality of the power. Power electronic devices such as Voltage Source Converter (VSC) based Static Synchronous Compensator (STATCOM) etc. can be used to mitigate the voltage problems in the distribution system. The voltage problems dealt with in this paper are to show how to mitigate unbalanced voltage sags and voltage unbalance in the CIGRE Low Voltage (LV) test network and net-works like this. The voltage unbala...

  9. Improving Stability of Pulse Modulator Technology

    Institute of Scientific and Technical Information of China (English)

    ZHANG; Li-feng; ZHU; Zhi-bin; LIU; Bao-jie; YANG; Sheng

    2015-01-01

    In high voltage pulse modulator,the RD loop and the primary winding of the pulse transformer is parallel,and the negative peak loop and the PFN is parallel.When the modulator is running,the resistor temperature of RD loops and the resistor temperature of reverse peak loop are too high,exceeding 100℃.It can work normally,

  10. Programmable high voltage power supply with regulation confined to the high voltage section

    Science.gov (United States)

    Castell, Karen D. (Inventor); Ruitberg, Arthur P. (Inventor)

    1994-01-01

    A high voltage power supply in a dc-dc converter configuration includes a pre-regulator which filters and regulates the dc input and drives an oscillator which applies, in turn, a low voltage ac signal to the low side of a step-up high voltage transformer. The high voltage side of the transformer drives a voltage multiplier which provides a stepped up dc voltage to an output filter. The output voltage is sensed by a feedback network which then controls a regulator. Both the input and output of the regulator are on the high voltage side, avoiding isolation problems. The regulator furnishes a portion of the drive to the voltage multiplier, avoiding having a regulator in series with the load with its attendant, relatively high power losses. This power supply is highly regulated, has low power consumption, a low parts count and may be manufactured at low cost. The power supply has a programmability feature that allows for the selection of a large range of output voltages.

  11. Transformerless DC-DC Converter Using Cockcroft-Walton Voltage Multiplier to Obtain High DC Voltage

    Directory of Open Access Journals (Sweden)

    Meghana G Naik,

    2014-11-01

    Full Text Available In the present scenario the use of transformer for high voltages in converter circuit reduces the overall operating efficiency due to leakage inductance and use of transformer also increases the operational cost. . Therefore the proposed system is implemented with transformer less DC-DC converter so as to obtain high DC voltage with the use of nine stage Cockcroft-Walton (CW voltage multiplier. The proposed converter operates in CCM (continuous conduction mode, so that the converter switch stress, the switching losses are reduced. The DC voltage at the input of the proposed model is low and is boosted up by boost inductor (Ls in DC-DC converter stage and performs inverter operation. The number of stages in CW-voltage multiplier circuit is applied with low input pulsating DC (AC Voltage voltage where it is getting converted to high DC output voltage. The proposed converter switches operates at two independent frequencies, modulating (fsm andalternating (fsc frequency. The fsm operates at higher frequency of the output while the fsc operates at lower frequency of the desired output voltage ripple and the output ripples can be adjusted by the switch Sc1 and Sc2. The regulation of the output voltage is achieved by controlling the Duty ratio.The simulation is carried over by the MATLABSIMULINK.

  12. Dependence of macrophage superoxide release on the pulse amplitude of an applied pressure regime: a potential factor at the soft tissue-implant interface.

    Science.gov (United States)

    Shin, Hainsworth Y; Frechette, Danielle M; Rohner, Nathan; Zhang, Xiaoyan; Puleo, David A; Bjursten, Lars M

    2016-03-01

    Failure of soft tissue implants has been largely attributed to the influence of biomaterial surface properties on the foreign body response, but some implant complications, e.g. macrophage accumulation and necrosis, are still not effectively addressed with surface treatments to minimize deleterious biomaterial effects. We explored an alternative explanation for implant failure, linking biocompatibility with implant micromotion-induced pressure fluctuations at the tissue-biomaterial interface. For this purpose, we used a custom in vitro system to characterize the effects of pressure fluctuations on the activity of macrophages, the predominant cells at a healing implant site. Initially, we quantified superoxide production by HL60-derived macrophage-like cells under several different pressure regimes with means of 5-40 mmHg, amplitudes of 0-15 mmHg and frequencies of 0-1.5 Hz. All pressure regimes tested elicited significantly (p superoxide production by macrophage-like cells relative to parallel controls. Notably, pressure-sensitive reductions in superoxide release correlated (r(2)  = 0.74; p superoxide production and cell viability, we also explored the influence of cyclic pressure on macrophage numbers and death. Compared to controls, adherent macrophage-like cells exposed to 7.5/2.5 mmHg cyclic pressures for 6 h exhibited significantly (p superoxide dismutase. Collectively, our results suggest that pressure pulses are a putative regulator of macrophage adhesion via a superoxide-related effect. Pressure fluctuations, e.g. due to implant micromotion, may, therefore, potentially modulate macrophage-dependent wound healing.

  13. Electric field measurements in a nanosecond pulse discharge in atmospheric air

    Science.gov (United States)

    Simeni Simeni, Marien; Goldberg, Benjamin M.; Zhang, Cheng; Frederickson, Kraig; Lempert, Walter R.; Adamovich, Igor V.

    2017-05-01

    The paper presents the results of temporally and spatially resolved electric field measurements in a nanosecond pulse discharge in atmospheric air, sustained between a razor edge high-voltage electrode and a plane grounded electrode covered by a thin dielectric plate. The electric field is measured by picosecond four-wave mixing in a collinear phase-matching geometry, with time resolution of approximately 2 ns, using an absolute calibration provided by measurements of a known electrostatic electric field. The results demonstrate electric field offset on the discharge center plane before the discharge pulse due to surface charge accumulation on the dielectric from the weaker, opposite polarity pre-pulse. During the discharge pulse, the electric field follows the applied voltage until ‘forward’ breakdown occurs, after which the field in the plasma is significantly reduced due to charge separation. When the applied voltage is reduced, the field in the plasma reverses direction and increases again, until the weak ‘reverse’ breakdown occurs, producing a secondary transient reduction in the electric field. After the pulse, the field is gradually reduced on a microsecond time scale, likely due to residual surface charge neutralization by transport of opposite polarity charges from the plasma. Spatially resolved electric field measurements show that the discharge develops as a surface ionization wave. Significant surface charge accumulation on the dielectric surface is detected near the end of the discharge pulse. Spatially resolved measurements of electric field vector components demonstrate that the vertical electric field in the surface ionization wave peaks ahead of the horizontal electric field. Behind the wave, the vertical field remains low, near the detection limit, while the horizontal field is gradually reduced to near the detection limit at the discharge center plane. These results are consistent with time-resolved measurements of electric field

  14. Single-step electropolymerization patterning of a polypyrrole nanowire by ultra-short pulses via an AFM cantilever

    Energy Technology Data Exchange (ETDEWEB)

    Nam, Kihwan; Lee, Gyudo; Jung, Huihun; Kim, Chi Hyun; Seo, Jongbum; Yoon, Dae Sung; Lee, Sang Woo; Kwon, Taeyun [Department of Biomedical Engineering, Yonsei University, Wonju, 220-710 (Korea, Republic of); Park, Jinsung, E-mail: yusuklee@yonsei.ac.kr, E-mail: tkwon@yonsei.ac.kr [Department of Mechanical Engineering, Korea University, Seoul, 136-701 (Korea, Republic of)

    2011-06-03

    Conducting polymers (CPs) have attracted a great deal of attention due to their unique properties; these properties are useful in implementing various functional devices, such as memory, and chemical and biological sensors. In particular, the nanopatterning of CPs is a key technology that will accelerate the adoption of CPs in fabricating nanoscaled multifunctional devices. This paper presents an innovative technique for forming polypyrrole nanowire (PPy-NW) patterns, without any additional pretreatment on the gold surface, using atomic force microscopy (AFM) and ultra-short pulse voltage. Applying the ultra-short pulse voltage to the AFM tip has the following advantage: since the electrochemical current is extremely localized around the tip, the successful formation of CP nanowires results. This is because the pulse width is much shorter than the resistor-capacitor (RC) time constant of the equivalent electrochemical circuit of our experimental set-up. This paper provides systematic results regarding the dimensional variation of the PPy-NW patterns produced by varying the electrical conditions of the ultra-short pulse, such as the pulse amplitude, width, and frequency. The results show that use of an ultra-short pulse is essential in fabricating PPy-NW patterns. Additionally, an ultra-short pulse offers excellent pattern controllability for both width (353 nm {approx} 3.37 {mu}m) and height (2.0 {approx} 88.3 nm).

  15. 一种用于低重复频率窄脉冲的脉冲稳偏技术%A Novel Technique Applied to Low Repetition Narrow Band Pulse Polarization Stabilization

    Institute of Scientific and Technical Information of China (English)

    王建军; 许党朋; 李明中; 林宏奂; 张锐; 邓颖; 谭敬; 孙力军; 周寿桓

    2011-01-01

    新一代高功率固体激光装置前端系统大多采用了先进的全光纤全固化技术路线,为了实现单模光纤系统长期稳定输出,需要对系统中的偏振态有针对性地进行控制.提出一种主动偏振控制实现单模光纤系统低重复频率窄脉冲偏振稳定的方法.利用该技术开发的脉冲稳偏器在重复频率大于100 Hz,脉冲宽度大于1.5 ns的情况下,系统输出稳定性可控制在均方根(RMS)为1%和峰谷值(PV)为7%左右.所开发的脉冲稳偏器成功应用于我国第二代高功率固体激光装置前端系统中,输出稳定性指标优于国家点火装置(NIF).该技术可广泛应用于窄脉冲和低重复频率系统中实现偏振态的主动控制.%The all-fiber and all-solidified technique was installed to the front end of the next generation high power laser system. Appropriate control to the polarization was required to maintain the stabilization of the fiber system. In order to maintain low repetition narrow band pulses' polarization stabilization, a novel active control technique applied to single mode fiber laser system which worked with low repetition narrow band pulses was proposed. A root-meansquare of 1% and a peak to valley ratio of 7 % stability were achieved, when the pulse polarization stabilizer based on this novel technique was used to 1.5 ns pulses at repetition above 100 Hz. The new polarization stabilizer was applied to fiber front end of the second generation high power laser system. The performance index was better than national ignition facility (NIF), and this technique could be used to control the polarization of the narrow-band and lowrepetition system actively.

  16. Low-Voltage Continuous Electrospinning Patterning.

    Science.gov (United States)

    Li, Xia; Li, Zhaoying; Wang, Liyun; Ma, Guokun; Meng, Fanlong; Pritchard, Robyn H; Gill, Elisabeth L; Liu, Ye; Huang, Yan Yan Shery

    2016-11-30

    Electrospinning is a versatile technique for the construction of microfibrous and nanofibrous structures with considerable potential in applications ranging from textile manufacturing to tissue engineering scaffolds. In the simplest form, electrospinning uses a high voltage of tens of thousands volts to draw out ultrafine polymer fibers over a large distance. However, the high voltage limits the flexible combination of material selection, deposition substrate, and control of patterns. Prior studies show that by performing electrospinning with a well-defined "near-field" condition, the operation voltage can be decreased to the kilovolt range, and further enable more precise patterning of fibril structures on a planar surface. In this work, by using solution dependent "initiators", we demonstrate a further lowering of voltage with an ultralow voltage continuous electrospinning patterning (LEP) technique, which reduces the applied voltage threshold to as low as 50 V, simultaneously permitting direct fiber patterning. The versatility of LEP is shown using a wide range of combination of polymer and solvent systems for thermoplastics and biopolymers. Novel functionalities are also incorporated when a low voltage mode is used in place of a high voltage mode, such as direct printing of living bacteria; the construction of suspended single fibers and membrane networks. The LEP technique reported here should open up new avenues in the patterning of bioelements and free-form nano- to microscale fibrous structures.

  17. Curling probe measurement of a large-volume pulsed plasma with surface magnetic confinement

    Science.gov (United States)

    Pandey, A.; Tashiro, H.; Sakakibara, W.; Nakamura, K.; Sugai, H.

    2016-12-01

    A curling probe (CP) based on microwave resonance is applied to the measurement of electron density in a pulsed DC glow discharge under surface magnetic confinement (SMC) provided by a number of permanent magnets on a chamber wall. Owing to the SMC effects, a 1 m scale large-volume plasma is generated by a relatively low voltage (~1 kV) at low pressure (~1 Pa) in various gases (Ar, CH4, and C2H2). Temporal variation of the electron density is measured for pulse frequency f  =  0.5-25 kHz for various discharge-on times (T ON) with a high resolution time (~0.2 µs), using the on-point mode. In general, the electron density starts to increase at time t  =  0 after turn-on of the discharge voltage, reaches peak density at t  =  T ON, and then decreases after turn-off. The peak electron density is observed to increase with the pulse frequency f for constant T ON owing to the residual plasma. This dependence is successfully formulated using a semi-empirical model. The spatio-temporal evolution of the cathode sheath in the pulsed discharge is revealed by a 1 m long movable CP. The measured thickness of the high-voltage cathode fall in a steady state coincides with the value of the so-called Child-Langmuir sheath.

  18. Treatment of Azo-dye Orange II with Nozzle-cylinder Electrode by Negative High-voltage Pulse Discharge System Combined with Ti02 Photocatalysis%喷嘴-筒式放电极负高压脉冲放电协同二氧化钛光催化对偶氮类染料酸性橙Ⅱ的处理

    Institute of Scientific and Technical Information of China (English)

    王少启; 孙明; 鲁晓辉; 郝夏桐

    2012-01-01

    The pulse discharge system produce discharge plasma and the high-energy electron, ultraviolet light, ozone etc, can be comprehensively dealt with water or atmospheric pollutants. In this paper, pulse discharge system combined with TiO2 photocatalysis, by designing nozzle-electrode of nozzle-cylinder reactor with coating of TiO2. With using ultraviolet of pulse discharge process to achieve catalytic of TiO2, for increaseing the active radicals quantity of primarily hydroxyl, The paper studied the azo-dye Orange Ⅱ to compare with coating of TiO2 electrode on degradation rate of pollutants. The main research is about degradation rate of acid orange Ⅱ in respectively with before and after coating on pulse peak voltage, pulse repetition frequency, discharge electrode diameter, initial concentration of solution and other factors.%脉冲放电过程在产生放电等离子体的同时,产生高能电子、紫外光.O3等多因素,可综合作用于水中或大气中的污染物。本文把脉冲放电等离子体和TiO2光催化相结合,对我们设计的喷嘴一筒式反应器中的喷嘴放电极进行二氧化钛镀膜,利用脉冲放电过程中的紫外光实现对二氧化钛的催化.增加放电过程以羟基为主的活性自由基的数量。以偶氮类染料酸性橙Ⅱ为研究对象,对比了放电极二氧化钛镀膜对放电等离子体技术对污染物降解效率的影响。研究了镀膜前后分别脉冲峰值电压,溶液初始浓度、溶液pH值、电导率等因素对偶氮类染料酸性橙Ⅱ液降解率的影响。

  19. Voltage controlled spintronics device for logic applications.

    Energy Technology Data Exchange (ETDEWEB)

    Bader, S. D.; You, C.-Y.

    1999-09-03

    We consider logic device concepts based on our previously proposed spintronics device element whose magnetization orientation is controlled by application of a bias voltage instead of a magnetic field. The basic building block is the voltage-controlled rotation (VCR) element that consists of a four-layer structure--two ferromagnetic layers separated by both nanometer-thick insulator and metallic spacer layers. The interlayer exchange coupling between the two ferromagnetic layers oscillates as a function of applied voltage. We illustrate transistor-like concepts and re-programmable logic gates based on VCR elements.

  20. Characteristics of a micro-gap argon barrier discharge excited by a saw-tooth voltage at atmospheric pressure

    Science.gov (United States)

    Li, Xuechen; Zhang, Qi; Jia, Pengying; Chu, Jingdi; Zhang, Panpan; Dong, Lifang

    2017-03-01

    Using two water electrodes, a micro-gap dielectric barrier discharge excited by a saw-tooth voltage is investigated in atmospheric pressure argon. Through electrical and optical measurements, it is found that, at a lower driving frequency, a stepped discharge mode is obtained per half voltage cycle. Moreover, the duration and amplitude of the current plateau increase with the increase in the applied peak voltage. With the increase in the driving frequency, the stepped discharge mode transits into a pulsed one after a multi-peak mode. During this process, a diffuse discharge at a lower frequency transits into a filamentary one at a higher frequency. Temporal evolutions of the discharges are investigated axially based on fast photography. It is found that the stepped mode is in atmospheric pressure Townsend discharge (APTD) regime. However, there is a transition from APTD to atmospheric pressure glow discharge for the pulsed mode. Spectral intensity ratio of 391.4 nm to 337.1 nm is used to determine the averaged electron energy, which decreases with increasing peak voltage or driving frequency.

  1. Kinetics deformation of current-voltage characteristics of the varistor oxide structures due to overcharging of the localized states

    Directory of Open Access Journals (Sweden)

    Tonkoshkur A. S.

    2014-12-01

    Full Text Available Prolonged exposure of zinc oxide varistors to the electrical load leads to current-voltage characteristics (CVC deformation, which is associated with a change in the height and width of the intergranular barriers, which are main structural element of the varistors. Polarization phenomena in zinc oxide ceramics are studied in a number of works, but those are mainly limited to the study of the physics of the CVC deformation process and to determining the parameters of localized electronic states involved in this process. This paper presents the results on the simulation of the deformation of pulse CVC of a separate intergranular potential barrier at transient polarization/depolarization, associated with recharging of surface electronic states (SES, which cause this barrier. It is found that at high density of SES their degree of electron filling is small and the effect of DC voltage leads to a shift of pulse current-voltage characteristics into the region of small currents. Conversely, the low density SES are almost completely filled with electrons, and after crystallite polarization CVC is shifted to high currents. Experimental studies have confirmed the possibility of applying the discovered laws to ceramic varistor structures. The proposed model allows interpreting the «anomalous» effects (such as increase in the classification voltage and reduction of active losses power observed during the varistors accelerated aging test.

  2. Voltage verification unit

    Science.gov (United States)

    Martin, Edward J.

    2008-01-15

    A voltage verification unit and method for determining the absence of potentially dangerous potentials within a power supply enclosure without Mode 2 work is disclosed. With this device and method, a qualified worker, following a relatively simple protocol that involves a function test (hot, cold, hot) of the voltage verification unit before Lock Out/Tag Out and, and once the Lock Out/Tag Out is completed, testing or "trying" by simply reading a display on the voltage verification unit can be accomplished without exposure of the operator to the interior of the voltage supply enclosure. According to a preferred embodiment, the voltage verification unit includes test leads to allow diagnostics with other meters, without the necessity of accessing potentially dangerous bus bars or the like.

  3. Installation for Treatment of Agricultural Products Using High-Voltage Discharges

    Directory of Open Access Journals (Sweden)

    Popescu V.S.

    2015-12-01

    Full Text Available The paper presents the results of the study on the determination and optimization of construction and technology parameters of an electro hydraulic installation developed for research in view of its use in primary processing of agricultural products. Unlike other processing technologies, the proposed technology using electro hydraulic effect requires the application of an installation, which is simple in terms of construction, has low cost, is reliable, easy to use and can be widely applied in various branches of agriculture including primary processing of agricultural products and for sterilizing liquids. The problem of using electro hydraulic effect consists in the correct dimensioning of the installation parameters to obtain high voltage pulses, in comparison with the dimensions of the chamber with electrodes, wherein the liquid processing is carried out. For dimensioning and development of the proposed installation, the necessary parameters were determined by calculation and were confirmed by conducting operational tests. The performed calculation and tests on the operation of the installation under laboratory conditions gave the possibility of dimensioning and optimization of the construction and technological parameters of electro-hydraulic installation, i.e. voltage level, the distance between the electrodes, the volume of the treated liquid, the treatment pulse number and the energy pulsed discharge. The values of the design parameters have allowed to develop and commission the installation, which will allow further tests on use of the electro-hydraulic effect in the processing the agricultural products in the Republic of Moldova.

  4. Scintillation properties of the YVO{sub 4}:Eu{sup 3+} compound in powder form. Its application to dosimetry in radiation fields produced by pulsed mega-voltage photon beams

    Energy Technology Data Exchange (ETDEWEB)

    Martinez, Nahuel; Molina, Pablo; Santiago, Martin; Caselli, Eduardo [National University of Central Buenos Aires, Tandil (Argentina). Inst. de Fisica Arroyo Seco; Teichmann, Tobias; Sommer, Marian; Henniger, Juergen [Dresden University of Technology (Germany). Radiation Physics Group

    2015-07-01

    The investigation of scintillation properties of europium doped yttrium orthovanadate shows the suitability of this material for fiber-based dose rate measurements. All measurements were carried out with a 6 MV Varian linear accelerator. The temperature dependence of the signal is lower than that of the plastic scintillators reported so far. By measuring the afterglow of probes between Linac-pulses, the signal due to the stem effect can be successfully eliminated. Comparison of depth dose profiles in a water phantom for radiation field dimensions between 1 x 1 cm{sup 2} and 10 x 10 cm{sup 2} shows that the probes are suitable for small fields having dimensions up to 1 x 1 cm{sup 2}. The high light yield of probes having dimensions of 1 mm opens up the possibility for their use in spatially confined radiation fields, such as in intensity-modulated radiotherapy (IMRT) and volume-modulated radiation therapy (VMAT).

  5. Research Progress of Inverse Power Law Applied in Lifetime Design of High Voltage Cable%反幂定律应用于高压电缆寿命设计的研究进展

    Institute of Scientific and Technical Information of China (English)

    廖雁群; 冯冰; 罗潘; 张连杰; 卢志华; 徐阳

    2016-01-01

    本文回顾了反幂定律的发展过程,用Eyring公式对反幂定律的正确性进行了理论解释,总结了反幂定律在确定高压电缆绝缘厚度和在电缆E-t寿命曲线中的应用,给出了温度修正的电老化寿命模型,阐述了温度在高压电缆寿命设计中的重要性。%The development process of the inverse power law was reviewed, and the correctness of inverse power law was theoretical explained with the Eyring equation. The application of the inverse power law in determining the thickness of high voltage cable insulation and the application in the life curves of cable were summarized. Finally, this paper presented the electrical ageing lifetime model revised by temperature and emphasized the importance of temperature in the lifetime design of high voltage cable.

  6. Pulse electrochemical machining on Invar alloy: Optical microscopic/SEM and non-contact 3D measurement study of surface analyses

    Energy Technology Data Exchange (ETDEWEB)

    Kim, S.H.; Choi, S.G.; Choi, W.K.; Yang, B.Y. [School of Mechanical Engineering, Inha University, Incheon 402-751 (Korea, Republic of); Lee, E.S., E-mail: leees@dreamwiz.com [Department of Mechanical Engineering, Inha University, Incheon 402-751 (Korea, Republic of)

    2014-09-30

    Highlights: • Invar alloy was electrochemically polished and then subjected to PECM (Pulse Electro Chemical Machining) in a mixture of NaCl, glycerin, and distilled water. • Optical microscopic/SEM and non-contact 3D measurement study of Invar surface analyses. • Analysis result shows that applied voltage and electrode shape are factors that affect the surface conditions. - Abstract: In this study, Invar alloy (Fe 63.5%, Ni 36.5%) was electrochemically polished by PECM (Pulse Electro Chemical Machining) in a mixture of NaCl, glycerin, and distilled water. A series of PECM experiments were carried out with different voltages and different electrode shapes, and then the surfaces of polished Invar alloy were investigated. The polished Invar alloy surfaces were investigated by optical microscope, scanning electron microscope (SEM), and non-contact 3D measurement (white light microscopes) and it was found that different applied voltages produced different surface characteristics on the Invar alloy surface because of the locally concentrated applied voltage on the Invar alloy surface. Moreover, we found that the shapes of electrode also have an effect on the surface characteristics on Invar alloy surface by influencing the applied voltage. These experimental findings provide fundamental knowledge for PECM of Invar alloy by surface analysis.

  7. Voltage biasing, cyclic voltammetry, & electrical impedance spectroscopy for neural interfaces.

    Science.gov (United States)

    Wilks, Seth J; Richner, Tom J; Brodnick, Sarah K; Kipke, Daryl R; Williams, Justin C; Otto, Kevin J

    2012-02-24

    Electrical impedance spectroscopy (EIS) and cyclic voltammetry (CV) measure properties of the electrode-tissue interface without additional invasive procedures, and can be used to monitor electrode performance over the long term. EIS measures electrical impedance at multiple frequencies, and increases in impedance indicate increased glial scar formation around the device, while cyclic voltammetry measures the charge carrying capacity of the electrode, and indicates how charge is transferred at different voltage levels. As implanted electrodes age, EIS and CV data change, and electrode sites that previously recorded spiking neurons often exhibit significantly lower efficacy for neural recording. The application of a brief voltage pulse to implanted electrode arrays, known as rejuvenation, can bring back spiking activity on otherwise silent electrode sites for a period of time. Rejuvenation alters EIS and CV, and can be monitored by these complementary methods. Typically, EIS is measured daily as an indication of the tissue response at the electrode site. If spikes are absent in a channel that previously had spikes, then CV is used to determine the charge carrying capacity of the electrode site, and rejuvenation can be applied to improve the interface efficacy. CV and EIS are then repeated to check the changes at the electrode-tissue interface, and neural recordings are collected. The overall goal of rejuvenation is to extend the functional lifetime of implanted arrays.

  8. Bio-Inspired Carbon Monoxide Sensors with Voltage-Activated Sensitivity

    KAUST Repository

    Savagatrup, Suchol

    2017-09-27

    Carbon monoxide (CO) outcompetes oxygen when binding to the iron center of hemeproteins, leading to a reduction in blood oxygen level and acute poisoning. Harvesting the strong specific interaction between CO and the iron porphyrin provides a highly selective and customizable sensor. We report the development of chemiresistive sensors with voltage-activated sensitivity for the detection of CO comprising iron porphyrin and functionalized single-walled carbon nanotubes (F-SWCNTs). Modulation of the gate voltage offers a predicted extra dimension for sensing. Specifically, the sensors show a significant increase in sensitivity toward CO when negative gate voltage is applied. The dosimetric sensors are selective to ppm levels of CO and functional in air. UV/Vis spectroscopy, differential pulse voltammetry, and density functional theory reveal that the in situ reduction of FeIII to FeII enhances the interaction between the F-SWCNTs and CO. Our results illustrate a new mode of sensors wherein redox active recognition units are voltage-activated to give enhanced and highly specific responses.

  9. SYNTHESIS OF VOLTAGES OF UNIFORM PWM IN TIME REGULATION

    Directory of Open Access Journals (Sweden)

    A. G. Stryzhniou

    2014-01-01

    Full Text Available The article describes a process of synthesis and qualitative assessment of the harmonic composition of voltages of multiple and single PWM pulses in time regulation, being, along with amplitude, frequency and phase method, one of control methods of an asynchronous motor. The main point of time regulation is that a pause after any two single PWM pulses with different polarity or after any two groups of multiple PWM pulses with different polarity changes during a process of regulation. Feature of time regulation is that a motor has fast response in the range of small-signal of control and good linearity of speed-torque characteristics in the whole control range. Analytical expressions of parameters of PWM pulses ai and ti are obtained which allow to simplify considerably a process of formation and implementation of time regulation using tabular or indexed-tabular methods. These expressions allow not only to define voltage amplitude of  harmonic but also to perform qualitative assessment of harmonic composition of output voltages at time regulation. It is specified that harmonic frequencies wi = w0/q change in inverse proportion to magnitude of parameter q during a process of regulation and there is a replacement of a fundamental frequency by frequencies of higher harmonics.The offered approach allows to synthesize voltage of uniform single and multiple PWM pulses and to perform their comparative and qualitative analysis and the obtained expressions can be used at modeling of AC motor work. Voltage of multiple PWM pulses which is formed using stepped reference voltage with even quantity of steps in a half period and a pause on a zero level has the best parameters by criterion of a minimum of harmonic components and a maximum of a factor of anharmonicity Kнс at time regulation.

  10. New energy management circuit applied in electric self-power supply over high voltage side%新型高压侧自供电电源设计与研究

    Institute of Scientific and Technical Information of China (English)

    李衍川; 江和

    2014-01-01

    分析了高压电场能量收集的原理,建立静电场耦合分布电容模型,并通过实验证明了模型的参考价值。随后,分析使用整流桥电路进行能量管理时的最佳功率点,并从增大超级电容充电电流的角度,设计了一种新型的管理电路,即同步电荷提取电路,以获得最佳的能量存储能力。结果证明存在一个最佳占空比使得收集的能量最大化,从而缩短无线节点在线监测工作周期。%The theory of energy harvested from the high voltage is analyzed, and then the corresponding model of coupling capacitance derived from static electric field is built, and several experiments are conducted to study whether the model is valuable. Then, according to what the result reveals, the optimal power point is found out when energy is managed by rectifier circuit. The value of charged current to super capacitor is used as the judge-ment whether the circuit system has the best storage performance. In that respect, management circuit is improved as a technology called Synchronous Electric Charge Extract, because the rectifier circuit can’ t perform as good as it is under ultrahigh voltage. It turns out that there is an optimal duty to maximize the energy harvested, so that the energy harvester can scavenge much more energy to cancellout the power loss. As a result, online monitoring period could be shortened greatly.

  11. Effect of applied bias voltage on corrosion-resistance for TiC{sub 1-x}N{sub x} and Ti{sub 1-x}Nb{sub x}C{sub 1-y}N{sub y} coatings

    Energy Technology Data Exchange (ETDEWEB)

    Caicedo, J.C., E-mail: Jcesarca@calima.univalle.edu.co [Department of Physics, Universidad del Valle, Ciudad Universitaria Melendez, A.A. 25360 Cali (Colombia); Department de Fisica Aplicada i Optica, Universitat de Barcelona, Catalunya (Spain); Amaya, C. [Department of Physics, Universidad del Valle, Ciudad Universitaria Melendez, A.A. 25360 Cali (Colombia); Laboratorio de Recubrimientos Duros DT-ASTIN SENA, Cali (Colombia); Yate, L. [Department de Fisica Aplicada i Optica, Universitat de Barcelona, Catalunya (Spain); Aperador, W.; Zambrano, G.; Gomez, M.E. [Department of Physics, Universidad del Valle, Ciudad Universitaria Melendez, A.A. 25360 Cali (Colombia); Alvarado-Rivera, J.; Munoz-Saldana, J. [Centro de Investigacion y de Estudios Avanzados del IPN, Unidad Queretaro (Mexico); Prieto, P. [Department of Physics, Universidad del Valle, Ciudad Universitaria Melendez, A.A. 25360 Cali (Colombia); Centro de Excelencia en Nuevos Materiales, Calle 13 100-00 Edificio 320, espacio 1026, Cali (Colombia)

    2010-02-15

    Corrosion-resistance behavior of titanium carbon nitride (Ti-C-N) and titanium niobium carbon nitride (Ti-Nb-C-N) coatings deposited onto Si(1 0 0) and AISI 4140 steel substrates via r.f. magnetron sputtering process was analyzed. The coatings in contact with a solution of sodium chloride at 3.5% were studied by Tafel polarization curves and impedance spectroscopy methods (EIS). Variations of the bias voltage were carried out for each series of deposition to observe the influence of this parameter upon the electrochemical properties of the coatings. The introduction of Nb in the ternary Ti-C-N film was evaluated via X-ray diffraction (XRD) analysis. The structure was characterized by using Raman spectroscopy to identify ternary and quaternary compounds. Surface corrosion processes were characterized using optical microscopy and scanning electron microscopy (SEM). XRD results show conformation of the quaternary phase, change in the strain of the film, and lattice parameter as the effect of the Nb inclusion. The main Raman bands were assigned to interstitial phases and 'impurities' of the coatings. Changes in Raman intensities were attributed to the incorporation of niobium in the Ti-C-N structure and possibly to resonance enhancement. Finally, the corrosion data obtained for Ti-C-N were compared with the results of corrosion tests of Ti-Nb-C-N coating. The results obtained showed that the incorporation of niobium to Ti-C-N coatings led to an increase in the corrosion-resistance. On another hand, an increase in the bias voltage led to a decrease in the corrosion-resistance for both Ti-C-N and Ti-Nb-C-N coatings.

  12. A Voltage Controller in Photo-Voltaic System with Battery Storage for Stand-Alone Applications

    Directory of Open Access Journals (Sweden)

    Ganesh Dharmireddy

    2012-01-01

    Full Text Available This paper proposes the new voltage controller in photo-voltaic system for Stand-Alone Applications with battery energy storage. The output of the PV array is unregulated DC supply due to change in weather conditions. The maximum power is tracked with respect to temperature and irradiance levels by using DC-DC converter. The perturbation and observes algorithm is applied for maximum power point tracking (MPPT purpose. This algorithm is selected due to its ability to withstand against any parameter variation and having high efficiency. The solar cell array powers the steady state energy and the battery compensates the dynamic energy in the system. The aim of the control strategy is to control the SEPIC converter and bi-direction DC-DC converter to operate in suitable modes according to the condition of solar cell and battery, so as to coordinate the two sources of solar cell and battery supplying power and ensure the system operates with high efficiency and behaviors with good dynamic performance. The output of DC-DC converter is converted to AC voltage by using inverter.  The AC output voltage and frequency are regulated. A closed loop voltage control for inverter is done by using unipolar sine wave pulse width modulation (SPWM. The regulated AC voltage is fed to AC standalone loads or grid integration. The overall system is designed, developed and validated by using MATLAB-SIMULINK. The simulation results demonstrate the effective working of MPPT algorithm, control strategy and voltage controller with SPWM technique for inverter in AC standalone load applications.

  13. Pulsed positive streamer discharges in air at high temperatures

    Science.gov (United States)

    Ono, Ryo; Kamakura, Taku

    2016-08-01

    Atmospheric-pressure air pulsed positive streamer discharges are generated in a 13 mm point-plane gap in the temperature range of 293 K-1136 K, and the effect of temperature on the streamer discharges is studied. When the temperature is increased, the product of applied voltage and temperature VT proportional to the reduced electric field can be used as a primary parameter that determines some discharge parameters regardless of temperature. For a given VT, the transferred charge per pulse, streamer diameter, product of discharge energy and temperature, and length of secondary streamer are almost constant regardless of T, whereas the streamer velocity decreases with increasing T and the decay rate of the discharge current is proportional to 1/T. The N2(C) emission intensity is approximately determined by the discharge energy independent of T. These results are useful to predict the streamer discharge and its reactive species production when the ambient temperature is increased.

  14. Measurement of thermophysical properties by a pulse-heating technique

    Institute of Scientific and Technical Information of China (English)

    Peng Xiao; Jingmin Dai; Qingwei Wang

    2007-01-01

    A technique is described for the dynamic measurement of selected thermophysical properties of electrically conducting solids in the temperature range from 1100 K to the melting point. Based on rapid resistive self-heating of the specimen from room temperature to any desired high temperature in several seconds by the passage of an electical current pulse through it, this technique measures the pertinent quantities such as current, voltage, randiance temperature, with sub-millisecond time resolution. The pulse-heating technique is applied to strip specimens. The radiance temperature is measured by high-speed pyrometry,normal spectral emissivity of the strips is measured by integrating sphere reflectometry. The normal spectral emissivity results are used to compute the true temperature of the specimens. The heat capacity,electrical resistivity, total hemispherical emissivity are evaluated in the temperature range from 1100 K to the melting point.

  15. Control Loop for a Pulse Generator of a Fast Septum Magnet using DSP and Fuzzy Logic

    CERN Document Server

    Aldaz-Carroll, E; Dieperink, J H; Schröder, G; Vossenberg, Eugène B

    1997-01-01

    A prototype of a fast pulsed eddy current septum magnet for one of thebeam extraction's from the SPS towards LHC is under development. The precision of the magnetic field must be better than ±1.0 10-4 during a flat top of 30 µs. The current pulse is generated by discharging the capacitors of a LC circuit that resonates on the 1st and on the 3rd harmonic of a sine wave with a repetition rate of 15 s. The parameters of the circuit and the voltage on the capacitors must be carefully adjusted to meet the specifications. Drifts during operation must be corrected between two pulses by mechanically adjusting the inductance of the coil in the generator as well as the primary capacitor voltage. This adjustment process is automated by acquiring the current pulse waveform with sufficient time and amplitude resolution, calculating the corrections needed and applying these corrections to the hardware for the next pulse. A very cost-effective and practical solution for this adjustment process is the integration of off-th...

  16. Effects of the pulse width on the reactive species production and DNA damage in cancer cells exposed to atmospheric pressure microsecond-pulsed helium plasma jets

    Science.gov (United States)

    Joh, Hea Min; Choi, Ji Ye; Kim, Sun Ja; Kang, Tae Hong; Chung, T. H.

    2017-08-01

    Plasma-liquid and plasma-cell interactions were investigated using an atmospheric pressure dc microsecond-pulsed helium plasma jet. We investigated the effects of the electrical parameters such as applied voltage and pulse width (determined by the pulse frequency and duty ratio) on the production of reactive species in the gas/liquid phases and on the DNA damage responses in the cancer cells. The densities of reactive species including OH radicals were estimated inside the plasma-treated liquids using a chemical probe method, and the nitrite concentration was detected by Griess assay. Importantly, the more concentration of OH resulted in the more DNA base oxidation and breaks in human lung cancer A549 cells. The data are very suggestive that there is strong correlation between the production of OH in the plasmas/liquids and the DNA damage.

  17. High Voltage Distribution

    Science.gov (United States)

    Norbeck, Edwin; Miller, Michael; Onel, Yasar

    2010-11-01

    For detector arrays that require 5 to 10 kV at a few microamps each for hundreds of detectors, using hundreds of HV power supplies is unreasonable. Bundles of hundreds of HV cables take up space that should be filled with detectors. A typical HV module can supply 1 ma, enough current for hundreds of detectors. It is better to use a single HV module and distribute the current as needed. We show a circuit that, for each detector, measures the current, cuts off the voltage if the current exceeds a set maximum, and allows the HV to be turned on or off from a control computer. The entire array requires a single HV cable and 2 or 3 control lines. This design provides the same voltage to all of the detectors, the voltage set by the single HV module. Some additional circuitry would allow a computer controlled voltage drop between the HV and each individual detector.

  18. Nanoparticle mechanics: deformation detection via nanopore resistive pulse sensing

    Science.gov (United States)

    Darvish, Armin; Goyal, Gaurav; Aneja, Rachna; Sundaram, Ramalingam V. K.; Lee, Kidan; Ahn, Chi Won; Kim, Ki-Bum; Vlahovska, Petia M.; Kim, Min Jun

    2016-07-01

    Solid-state nanopores have been widely used in the past for single-particle analysis of nanoparticles, liposomes, exosomes and viruses. The shape of soft particles, particularly liposomes with a bilayer membrane, can greatly differ inside the nanopore compared to bulk solution as the electric field inside the nanopores can cause liposome electrodeformation. Such deformations can compromise size measurement and characterization of particles, but are often neglected in nanopore resistive pulse sensing. In this paper, we investigated the deformation of various liposomes inside nanopores. We observed a significant difference in resistive pulse characteristics between soft liposomes and rigid polystyrene nanoparticles especially at higher applied voltages. We used theoretical simulations to demonstrate that the difference can be explained by shape deformation of liposomes as they translocate through the nanopores. Comparing our results with the findings from electrodeformation experiments, we demonstrated that the rigidity of liposomes can be qualitatively compared using resistive pulse characteristics. This application of nanopores can provide new opportunities to study the mechanics at the nanoscale, to investigate properties of great value in fundamental biophysics and cellular mechanobiology, such as virus deformability and fusogenicity, and in applied sciences for designing novel drug/gene delivery systems.Solid-state nanopores have been widely used in the past for single-particle analysis of nanoparticles, liposomes, exosomes and viruses. The shape of soft particles, particularly liposomes with a bilayer membrane, can greatly differ inside the nanopore compared to bulk solution as the electric field inside the nanopores can cause liposome electrodeformation. Such deformations can compromise size measurement and characterization of particles, but are often neglected in nanopore resistive pulse sensing. In this paper, we investigated the deformation of various

  19. High voltage engineering fundamentals

    CERN Document Server

    Kuffel, E; Hammond, P

    1984-01-01

    Provides a comprehensive treatment of high voltage engineering fundamentals at the introductory and intermediate levels. It covers: techniques used for generation and measurement of high direct, alternating and surge voltages for general application in industrial testing and selected special examples found in basic research; analytical and numerical calculation of electrostatic fields in simple practical insulation system; basic ionisation and decay processes in gases and breakdown mechanisms of gaseous, liquid and solid dielectrics; partial discharges and modern discharge detectors; and over

  20. Study of the selective effect on cells induced by nanosecond pulsed electric field with the resistor-capacitor circuit model

    Institute of Scientific and Technical Information of China (English)

    Xu Fei; Xiao Dengming; Li Zhaozhi

    2009-01-01

    A resistor-capacitor (RC) circuit model is proposed to study the effect of nanosecond pulsed electric field on cells according to the structure and electrical parameters of cells. After a nanosecond step field has been applied, the variation of voltages across cytomembrane and mitochondria membrane both in normal and in malignant cells are studied with this model. The time for selectively targeting the mitochondria membrane and malignant cell can be evaluated much easily with curves that show the variation of voltage across each membrane with time. Ramp field is the typical field applied in electrobiology. The voltages across each membrane induced by ramp field are analyzed with this model. To selectively target the mitochondria membrane, proper range of ramp slope is needed. It is relatively difficult to decide the range of a slope to selectively affect the malignant cell. Under some conditions, such a range even does not exist.