WorldWideScience

Sample records for voltage divider configuration

  1. Inductive voltage divider modeling in Matlab

    Science.gov (United States)

    Andreev, S. A.; Kim, V. L.

    2017-01-01

    Inductive voltage dividers have the most appropriate metrological characteristics on alternative current and are widely used for converting physical signals. The model of a double-decade inductive voltage divider was designed with the help of Matlab/Simulink. The first decade is an inductive voltage divider with balanced winding, the second decade is a single-stage inductive voltage divider. In the paper, a new transfer function algorithm was given. The study shows errors and differences that appeared between the third degree reduced model and a twenty degree unreduced model. The obtained results of amplitude error differ no more than by 7 % between the reduced and unreduced model.

  2. Enhanced Model of Nonlinear Spiral High Voltage Divider

    Directory of Open Access Journals (Sweden)

    V. Panko

    2015-04-01

    Full Text Available This paper deals with the enhanced accurate DC and RF model of nonlinear spiral polysilicon voltage divider. The high resistance polysilicon divider is a sensing part of the high voltage start-up MOSFET transistor that can operate up to 700 V. This paper presents the structure of a proposed model, implemented voltage, frequency and temperature dependency, and scalability. A special attention is paid to the ability of the created model to cover the mismatch and influence of a variation of process parameters on the device characteristics. Finally, the comparison of measured data vs. simulation is presented in order to confirm the model validity and a typical application is demonstrated.

  3. Binary Versus Decade Inductive Voltage Divider Comparison and Error Decomposition

    Science.gov (United States)

    1995-08-01

    1995 IEEE Authorized licensed use limited to: US Naval Academy. Downloaded on January 30, 2009 at 11:28 from IEEE Xplore . Restrictions apply...Downloaded on January 30, 2009 at 11:28 from IEEE Xplore . Restrictions apply. 906 s, A U U U U U l f U U J s, sa I IEEE TRANSACTIONS ON...30, 2009 at 11:28 from IEEE Xplore . Restrictions apply. AVRAMOV-ZAMUROVIC et al.: BINARY VERSUS DECADE INDUCTIVE VOLTAGE DIVIDER COMPARISON AND ERROR

  4. Program-Controlled High Voltage Module in Active Voltage Dividers(AVD) for MPGD

    CERN Document Server

    Ginting, Muhammad Fadhil

    2016-01-01

    Micro Pattern Gas Detectors (MPGD) applications are rapidly developing and became an important part of upgrades for the LHC detectors. RD51/CERN have worked on Active Voltage Divider (AVD) technology for multistage MPGDs, One of the next developments for the AVD is to design and integrate high voltage module in a single box. The Program-Controlled High Voltage Module, part of one AIDA2020 project, has been successfully designed and developed, and can be integrated in AVD design.

  5. Next generation KATRIN high precision voltage divider for voltages up to 65kV

    CERN Document Server

    Bauer, S; Hochschulz, F; Ortjohann, H -W; Rosendahl, S; Thümmler, T; Schmidt, M; Weinheimer, C

    2013-01-01

    The KATRIN (KArlsruhe TRItium Neutrino) experiment aims to determine the mass of the electron antineutrino with a sensitivity of 200meV by precisely measuring the electron spectrum of the tritium beta decay. This will be done by the use of a retarding spectrometer of the MAC-E-Filter type. To achieve the desired sensitivity the stability of the retarding potential of -18.6kV has to be monitored with a precision of 3ppm over at least two months. Since this is not feasible with commercial devices, two ppm-class high voltage dividers were developed, following the concept of the standard divider for DC voltages of up to 100kV of the Physikalisch-Technische Bundesanstalt (PTB). In order to reach such high accuracies different effects have to be considered. The two most important ones are the temperature dependence of resistance and leakage currents, caused by insulators or corona discharges. For the second divider improvements were made concerning the high-precision resistors and the thermal design of the divider....

  6. HIGH VOLTAGE SMALL – SIZED ALTERNATIVE CURRENT RESISTIVE DIVIDERS FROM MICROWIRE

    Directory of Open Access Journals (Sweden)

    Berzan V.P.

    2011-04-01

    Full Text Available The paper discusses the design parameters and characteristics of the new product, the resistive voltage divider produced from microwire for measuring high-voltage alternating current. Resistive dividers are designed for use in AC circuits and power-frequency electric traction network traffic. Dividers have smaller mass-dimensional size compared with the measuring voltage transformers and higher accuracy class 0.2 at a fixed frequency.

  7. A novel water resistor divider with a coaxial low-voltage arm.

    Science.gov (United States)

    Jia, Wei; Chen, Weiqing; Mao, Congguang; Zeng, Jiangtao

    2010-03-01

    A new style high voltage resistor divider made of saline solution has been constructed and tested. A coaxial construction is used on the low-voltage arm, as the signal extraction electrode, which can increase the attenuation ratio of the divider. The time response of divider limited by the stray parameter also can be improved. Comparing the results of calibrated experiment with the commonly used equal size copper sulfate dividers, the new probe has nearly five times increase in the attenuation ratio. The time response of the new style divider in the dimension of 30 mm in diameter and 400 mm in length can reach to 1 ns.

  8. A Study on the step response characteristics in shielded resistor divider for full lightning impulse voltage

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Ik Soo; Lee, Hyeong Ho [Korea Electrotehnology Research Institute, Changwon (Korea, Republic of); Cho, Jung Soo; Park, Jung Hoo [Pusan National University, Pusan (Korea, Republic of)

    1996-02-01

    This paper presents the development technology of standard shielded resistor divider for full lightning impulse voltage. The ability of large-capacity power apparatus to withstand lighting stroke is usually evaluated by means of full lightning impulse voltage. Lightning impulse voltage test has been essential to evaluate the insulation performance of electrical power apparatus. Recently international standard (IEC 60) on high voltage measurement techniques is being revised and requests a formal traceability of high voltage measurements. Therefore, general interest for this area has grown considerably during last years, and several international intercomparisons have already completed worldwide, i.e. Europe, Japan, America etc., In this viewpoint, we have also investigated the step response of the standard shielded resistor divider, which satisfies the IEC recommendation. (author). 7 refs., 14 figs., 2 tabs.

  9. An Internal ALD-Based High Voltage Divider and Signal Circuit for MCP-based Photodetectors

    Energy Technology Data Exchange (ETDEWEB)

    Adams, Bernhard W.; Elagin, Andrey; Elam, Jeffrey W.; Frisch, Henry J.; Genat, Jean-Francois; Gregar, Joseph S.; Mane, Anil U.; Minot, Michael J.; Northrup, Richard; Obaid, Razib; Oberla, Eric; Alexander, Vostrikov; Wetstein, Matthew

    2015-04-21

    We describe a pin-less design for the high voltage (HV) resistive divider of the all-glass LAPPD (TM) 8 in,square thin photodetector module. The divider, which distributes high voltage applied to the photocathode to the two micro-channel plates (MCPs) that constitute the amplification stage, is comprised of the two MCPs and three glass mechanical spacers, each of which is coated with a resistive layer using atomic layer deposition (ALD). The three glass grid spacers and the two MCPs form a continuous resistive path between cathode and anode, with the voltages across the MCPs and the spacers determined by the resistance of each. High voltage is applied on an external tab on the top glass window that connects to the photocathode through the metal seal. The DC ground is supplied by microstrips on the bottom glass plate that form the high-bandwidth anode. The microstrips exit the package through the glass-frit seal of the anode base-plate and the package sidewall. The divider is thus completely internal, with no HV pins penetrating the low-profile flat glass package. Measurements of the performance of the divider are presented for the 8 in.-square MCP and spacer package in a custom test fixture and for an assembled externally pumped LAPPD (TM) prototype with an aluminum photocathode. (C) 2015 Elsevier B.V. All rights reserved.

  10. Investigation about decoupling capacitors of PMT voltage divider effects on neutron-gamma discrimination

    Energy Technology Data Exchange (ETDEWEB)

    Divani, Nazila, E-mail: n-divani@birjand.ac.ir; Firoozabadi, Mohammad M. [Dep. Of Physics, Faculty of Science, University of Birjand, Birjand (Iran, Islamic Republic of); Bayat, Esmail [Nuclear Science and Technology Research Institute, Atomic Energy Organization of Iran (Iran, Islamic Republic of)

    2014-11-24

    Scintillators are almost used in any nuclear laboratory. These detectors combine of scintillation materials, PMT and a voltage divider. Voltage dividers are different in resistive ladder design. But the effect of decoupling capacitors and damping resistors haven’t discussed yet. In this paper at first a good equilibrium circuit designed for PMT, and it was used for investigating about capacitors and resistors in much manner. Results show that decoupling capacitors have great effect on PMT output pulses. In this research, it was tried to investigate the effect of Capacitor’s value and places on PMT voltage divider in Neutron-Gamma discrimination capability. Therefore, the voltage divider circuit for R329-02 Hamamatsu PMT was made and Zero Cross method used for neutron-gamma discrimination. The neutron source was a 20Ci Am-Be. Anode and Dynode pulses and discrimination spectrum were saved. The results showed that the pulse height and discrimination quality change with the value and setting of capacitors.

  11. ELABORATION AND TESTING OF SOFTWARE FOR SIGNAL PROCESSING OF RESISTIVE HIGH VOLTAGE DIVIDER

    Directory of Open Access Journals (Sweden)

    Sit М.

    2009-12-01

    Full Text Available Mathematical tools and the software for input in the computer of signals of a resistive divider of a high voltage of the industrial frequency, providing a split-hair accuracy of measurement of parameters of the basic and harmonics which are divisible to the basic is developed.

  12. Effect of Layers Position on Fracture Toughness of Functionally Graded Steels in Crack Divider Configuration

    Institute of Scientific and Technical Information of China (English)

    Ali Nazari; Jamshid Aghazadeh Mohandesi; Shadi Riahi

    2011-01-01

    In the present study, fracture toughness of functionally graded steels in crack divider configuration has been modeled. By utilizing plain carbon and austenitic stainless steels slices with various thicknesses and arrangements as electroslag remelting electrodes, functionally graded steels were produced. The fracture toughness of the functionally graded steels in crack divider configuration has been found to depend on the composites' type together with the volume fraction and the position of the containing phases. According to the area under stress-strain curve of each layer in the functionally graded steels, a mathematical model has been presented for predicting fracture toughness of composites by using the rule of mixtures. The fracture toughness of each layer has been modified according to the position of that layer where for the edge layers, net plane stress condition was supposed and for the central layers, net plane strain condition was presumed. There is a good agreement between experimental results and those acquired from the analytical model.

  13. KCNE1 divides the voltage sensor movement in KCNQ1/KCNE1 channels into two steps

    Science.gov (United States)

    Barro-Soria, Rene; Rebolledo, Santiago; Liin, Sara I.; Perez, Marta E.; Sampson, Kevin J.; Kass, Robert S.; Larsson, H. Peter

    2014-04-01

    The functional properties of KCNQ1 channels are highly dependent on associated KCNE-β subunits. Mutations in KCNQ1 or KCNE subunits can cause congenital channelopathies, such as deafness, cardiac arrhythmias and epilepsy. The mechanism by which KCNE1-β subunits slow the kinetics of KCNQ1 channels is a matter of current controversy. Here we show that KCNQ1/KCNE1 channel activation occurs in two steps: first, mutually independent voltage sensor movements in the four KCNQ1 subunits generate the main gating charge movement and underlie the initial delay in the activation time course of KCNQ1/KCNE1 currents. Second, a slower and concerted conformational change of all four voltage sensors and the gate, which opens the KCNQ1/KCNE1 channel. Our data show that KCNE1 divides the voltage sensor movement into two steps with widely different voltage dependences and kinetics. The two voltage sensor steps in KCNQ1/KCNE1 channels can be pharmacologically isolated and further separated by a disease-causing mutation.

  14. Unique Power Dense, Configurable, Robust, High-Voltage Power Supplies Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Princeton Power will develop and deliver three small, lightweight 50 W high-voltage power supplies that have a configurable output voltage range from 500 to 50 kVDC....

  15. Toward the Optimal Configuration of Dynamic Voltage Scaling Points in Real-Time Applications

    Institute of Scientific and Technical Information of China (English)

    Hui-Zhan Yi; Xue-Jun Yang

    2006-01-01

    In real-time applications, compiler-directed dynamic voltage scaling (DVS) could reduce energy consumption efficiently, where compiler put voltage scaling points in the proper places, and the supply voltage and clock frequency were adjusted to the relationship between the reduced time and the reduced workload. This paper presents the optimal configuration of dynamic voltage scaling points without voltage scaling overhead, which minimizes energy consumption. The conclusion is proved theoretically. Finally, it is confirmed by simulations with equally-spaced voltage scaling configuration.

  16. Fault Analysis of DC Voltage Dividers in Xiangjiaba--Shanghai ±800 kV UHVDC Project

    Institute of Scientific and Technical Information of China (English)

    LI Fengqi; SHE Zhengqiu; LOU Dianqiang; Rajendra Iyer; Urban Astrom

    2012-01-01

    Transient DC voltage measurement error has been observed several times ever since Xiangjiaba--Shanghai ±800 kV UHVDC project started its commercial operation. The measurement error causes considerable disturbances to the AC networks. By analyzing the time frequency record, simulating faults at different positions of the divider, and testing the gas in voltage dividers, the fault is located and then is proved to be some partial discharges inside DC voltage dividers. The reason of the internal flashes and the solution to the problem is also discussed in this paper. The conclusion is that instead of N2 , SF6 should be used for the internal insulation of high voltage DC voltage dividers.

  17. Analysis of the match problem of a capacitive voltage divider with a long measurement cable

    Science.gov (United States)

    Yu, Bin-Xiong; Li, Rui; Su, Jian-Cang; Zhao, Liang; Zhang, Yu; Zheng, Lei; Zeng, Bo; Cheng, Jie; Gao, Peng-Cheng; Qiu, Xu-Dong; Xu, Xu-dong

    2017-09-01

    Research is carried out on the basis of the traditional two-end matched circuit of a capacitive voltage divider with a long measurement cable. Transmission progress in the circuit is analyzed theoretically. A match condition of the circuit is acquired, which requires that the circuit satisfies two conditions: (1) the measurement error should be small for a pulse with a duration of less than twice the delay time of the measurement cable; (2) the initial division ratio and the stable division ratio of the circuit are the same. Two matched methods of the circuit are acquired, including the first-order matched method and the second-order matched method. Numerical simulations are carried out. According to the simulation results, the relative errors of the circuits with a cable of 20 m are less than 1.5%, obtained by using both match methods for measurement of rectangular pulses with rise and fall times of 5 ns. An improved circuit is presented, which is suitable for any situation where the low-voltage capacitance of the capacitive divider is even smaller than the capaictance of the measurement cable. A verification experment is carried out, and the test result confirms the simulation result.

  18. Spectroscopic measurements with a silicon drift detector having a continuous implanted drift cathode-voltage divider

    CERN Document Server

    Bonvicini, V; D'Acunto, L; Franck, D; Gregorio, A; Pihet, P; Rashevsky, A; Vacchi, A; Vinogradov, L I; Zampa, N

    2000-01-01

    A silicon drift detector (SDD) prototype where the drift electrode also plays the role of a high-voltage divider has been realised and characterised for spectroscopic applications at near-room temperatures. Among the advantages of this design, is the absence of metal on the sensitive surface which makes this detector interesting for soft X-rays. The detector prototype has a large sensitive area (2x130 mm sup 2) and the charge is collected by two anodes (butterfly-like detector). The energy resolution of a such a detector has been investigated at near-room temperatures using a commercial, hybrid, low-noise charge-sensitive preamplifier. The results obtained for the X-ray lines from sup 5 sup 5 Fe and sup 2 sup 4 sup 1 Am are presented.

  19. Performance Evaluation of Three Different Inverter Configurations of DVR for Mitigation of Voltage Events

    Directory of Open Access Journals (Sweden)

    Miska Prasad

    2016-12-01

    Full Text Available The voltage events namely voltage sags and voltage swells represent the most common, frequent and important power quality events in today’s power system. Dynamic voltage restorer (DVR is one of the key components used to mitigate the supply voltage quality disturbances in terms of voltage sags and swells in the distribution system. It consists of an energy storage unit, a voltage source inverter, a filter, a coupling transformer and the control system. This paper presents three different inverter configurations of dynamic voltage restorer (DVR for mitigation of voltage events such as voltage sags and swells with sudden addition or removal of the nonlinear load. These three configurations are voltage source inverter based DVR (VSI-DVR, current source inverter based DVR (CSI-DVR and impedance or Z-source inverter based DVR (ZSI-DVR. The d-q control technique is used to control the operation of the DVR. The response of ZSI-DVR for mitigation of voltage sags and swells are investigated and compared with VSI-DVR and CSI-DVR using MATLAB/SIMULINK environment.

  20. Characterization of interdigitated electrode structures for water contaminant detection using a hybrid voltage divider and a vector network analyzer.

    Science.gov (United States)

    Rodríguez-Delgado, José Manuel; Rodríguez-Delgado, Melissa Marlene; Mendoza-Buenrostro, Christian; Dieck-Assad, Graciano; Omar Martínez-Chapa, Sergio

    2012-01-01

    Interdigitated capacitive electrode structures have been used to monitor or actuate over organic and electrochemical media in efforts to characterize biochemical properties. This article describes a method to perform a pre-characterization of interdigitated electrode structures using two methods: a hybrid voltage divider (HVD) and a vector network analyzer (VNA). Both methodologies develop some tests under two different conditions: free air and bi-distilled water media. Also, the HVD methodology is used for other two conditions: phosphate buffer with laccase (polyphenoloxidase; EC 1.10.3.2) and contaminated media composed by a mix of phosphate buffer and 3-ethylbenzothiazoline-6-sulfonic acid (ABTS). The purpose of this study is to develop and validate a characterization methodology using both, a hybrid voltage divider and VNA T-# network impedance models of the interdigitated capacitive electrode structure that will provide a shunt RC network of particular interest in detecting the amount of contamination existing in the water solution for the media conditions. This methodology should provide us with the best possible sensitivity in monitoring water contaminant media characteristics. The results show that both methods, the hybrid voltage divider and the VNA methodology, are feasible in determining impedance modeling parameters. These parameters can be used to develop electric interrogation procedures and devices such as dielectric characteristics to identify contaminant substances in water solutions.

  1. Comparison of divided and full pupil configurations for line-scanning confocal microscopy in human skin and oral mucosa

    Science.gov (United States)

    Larson, Bjorg; Abeytunge, Sanjeewa; Glazowski, Chris; Rajadhyaksha, Milind

    2012-02-01

    Confocal point-scanning microscopy has been showing promise in the detection, diagnosing and mapping of skin lesions in clinical settings. The noninvasive technique allows provides optical sectioning and cellular resolution for in vivo diagnosis of melanoma and basal cell carcinoma and pre-operative and intra-operative mapping of margins. The imaging has also enabled more accurate "guided" biopsies while minimizing the otherwise large number of "blind" biopsies. Despite these translational advances, however, point-scanning technology remains relatively complex and expensive. Line-scanning technology may offer an alternative approach to accelerate translation to the clinic. Line-scanning, using fewer optical components, inexpensive linear-array detectors and custom electronics, may enable smaller, simpler and lower-cost confocal microscopes. A line is formed using a cylindrical lens and scanned through the back focal plane of the objective with a galvanometric scanner. A linear CCD is used for detection. Two pupil configurations were compared for performance in imaging human tissue. In the full-pupil configuration, illumination and detection is made through the full objective pupil. In the divided pupil approach, half the pupil is illuminated and the other half is used for detection. The divided pupil configuration loses spatial and axial resolution due to a diminished NA, but the sectioning capability and rejection of background is improved. Imaging in skin and oral mucosa illustrate the performance of the two configurations.

  2. Water dissociation phenomena in a bipolar membrane——The configurations and theoretical voltage analysis

    Institute of Scientific and Technical Information of China (English)

    徐铜文; 杨伟华; 何炳林

    1999-01-01

    The models were established for the theoretical current-voltage characteristics in water dissociation process on a bipolar membrane. Particular attention was given to the transport of the water ions and electrolyte ions as well as the membrane physical structure and configuration. The factors on the water splitting process were adequately analysed based on the derived theoretical current-voltage characteristics and several good suggestions were proposed for decreasing the work voltage in practical operations. In addition, the model can give a reasonable explanation for the catalytic effect of some chemicals, such as amphiprotic hydroxide compounds, weak polymeric acids and bases, etc. It is shown that the catalyst may be responsible for the increase in dissociation rate constant of water and therefore enhance the water dissociation. The guidelines for choosing a proper catalyst were also proposed.

  3. Electrochemical treatment of reverse osmosis concentrate on boron-doped electrodes in undivided and divided cell configurations

    Energy Technology Data Exchange (ETDEWEB)

    Bagastyo, Arseto Y. [Advanced Water Management Centre, The University of Queensland, St Lucia, QLD 4072 (Australia); Department of Environmental Engineering, Institut Teknologi Sepuluh Nopember, Surabaya 60111 (Indonesia); Batstone, Damien J. [Advanced Water Management Centre, The University of Queensland, St Lucia, QLD 4072 (Australia); Kristiana, Ina [Curtin Water Quality Research Centre, Resources and Chemistry Precinct, Department of Chemistry, Curtin University, Bentley, Perth, WA 6102 (Australia); Escher, Beate I. [National Research Centre for Environmental Toxicology (Entox), The University of Queensland, Brisbane, QLD 4108 (Australia); Joll, Cynthia [Curtin Water Quality Research Centre, Resources and Chemistry Precinct, Department of Chemistry, Curtin University, Bentley, Perth, WA 6102 (Australia); Radjenovic, Jelena, E-mail: j.radjenovic@uq.edu.au [Advanced Water Management Centre, The University of Queensland, St Lucia, QLD 4072 (Australia)

    2014-08-30

    Highlights: • 100% of COD and ∼70% of DOC was removed in both cell configurations. • ∼21.7 mg L{sup −1} of AOCl and ∼2.3 mg L{sup −1} of AOBr was formed regardless of the membrane use. • The TEQ was far lower than expected given the high AOCl concentrations. • The undivided cell consumed lower energy compared to the divided cell. - Abstract: An undivided electrolytic cell may offer lower electrochlorination through reduction of chlorine/hypochlorite at the cathode. This study investigated the performance of electrooxidation of reverse osmosis concentrate using boron-doped diamond electrodes in membrane-divided and undivided cells. In both cell configurations, similar extents of chemical oxygen demand and dissolved organic carbon removal were obtained. Continuous formation of chlorinated organic compounds was observed regardless of the membrane presence. However, halogenation of the organic matter did not result in a corresponding increase in toxicity (Vibrio fischeri bioassay performed on extracted samples), with toxicity decreasing slightly until 10 Ah L{sup −1}, and generally remaining near the initial baseline-toxicity equivalent concentration (TEQ) of the raw concentrate (i.e., ∼2 mg L{sup −1}). The exception was a high range toxicity measure in the undivided cell (i.e., TEQ = 11 mg L{sup −1} at 2.4 Ah L{sup −1}), which rapidly decreased to 4 mg L{sup −1}. The discrepancy between the halogenated organic matter and toxicity patterns may be a consequence of volatile and/or polar halogenated by-products formed in oxidation by OH· electrogenerated at the anode. The undivided cell exhibited lower energy compared to the divided cell, 0.25 kWh gCOD{sup −1} and 0.34 kWh gCOD{sup −1}, respectively, yet it did not demonstrate any improvement regarding by-products formation.

  4. Electrochemical treatment of reverse osmosis concentrate on boron-doped electrodes in undivided and divided cell configurations.

    Science.gov (United States)

    Bagastyo, Arseto Y; Batstone, Damien J; Kristiana, Ina; Escher, Beate I; Joll, Cynthia; Radjenovic, Jelena

    2014-08-30

    An undivided electrolytic cell may offer lower electrochlorination through reduction of chlorine/hypochlorite at the cathode. This study investigated the performance of electrooxidation of reverse osmosis concentrate using boron-doped diamond electrodes in membrane-divided and undivided cells. In both cell configurations, similar extents of chemical oxygen demand and dissolved organic carbon removal were obtained. Continuous formation of chlorinated organic compounds was observed regardless of the membrane presence. However, halogenation of the organic matter did not result in a corresponding increase in toxicity (Vibrio fischeri bioassay performed on extracted samples), with toxicity decreasing slightly until 10AhL(-1), and generally remaining near the initial baseline-toxicity equivalent concentration (TEQ) of the raw concentrate (i.e., ∼2mgL(-1)). The exception was a high range toxicity measure in the undivided cell (i.e., TEQ=11mgL(-1) at 2.4AhL(-1)), which rapidly decreased to 4mgL(-1). The discrepancy between the halogenated organic matter and toxicity patterns may be a consequence of volatile and/or polar halogenated by-products formed in oxidation by OH electrogenerated at the anode. The undivided cell exhibited lower energy compared to the divided cell, 0.25kWhgCOD(-1) and 0.34kWhgCOD(-1), respectively, yet it did not demonstrate any improvement regarding by-products formation.

  5. High Voltage Resistive Divider Based on Cast Microwire in Glass Insulation on 6–24 kV Alternating Current of Commercial Frequency.

    Directory of Open Access Journals (Sweden)

    Juravleov A.

    2008-12-01

    Full Text Available It is presented the analysis and description of the construction of the high voltage resistive divider on the base of cast microwire in glass insulation on 6–24 kV alternating current of commercial frequency. It is presented the procedure of compensation of frequency error during the process of fabrication of divides and results of tests of the sample model of the divider as well.

  6. Discharge ignition in the diaphragm configuration supplied by DC non-pulsing voltage

    Science.gov (United States)

    Hlochová, L.; Hlavatá, L.; Kozáková, Z.; Krčma, F.

    2016-05-01

    This work deals with the ignition of the discharge in the diaphragm configuration generated in water solutions containing supporting NaCl electrolyte. The reactor has volume of 110 ml and it is made of polycarbonate. HV electrodes made of stainless steel are placed in this reactor. Ceramic (Shapal-MTM) diaphragm is placed in the barrier separating the cathode and the anode space. An electric power source supplies the reactor by constant DC voltage up to 4 kV and electric current up to 300 mA. The discharge ignition is compared in the reactor with different sizes of diaphragms. Measurements are carried out in electrolyte solutions with the same conductivity. Images of plasma streamers and bubble formation are taken by an ICCD camera iStar 734. Electrical characteristics are measured by an oscilloscope LeCroy LT 374 L in order to determine breakdown moments at different experimental conditions.

  7. Low voltage electrodeposition of CN x films and study of the effect of the deposition voltage on bonding configurations

    Science.gov (United States)

    Sreejith, K.; Nuwad, J.; Pillai, C. G. S.

    2005-10-01

    Carbon nitride (CN x) films were deposited from acetonitrile at low voltage (150-450 V) through electrodeposition. The films were characterized by atomic force microscopy (AFM), Raman spectroscopy and Fourier transform infrared (FT-IR) spectroscopy. AFM investigations revealed that the grain size was ˜200 nm and roughness was ˜10 nm. The films were found to be continuous and close packed. IR spectra revealed existence of strong sp 3, sp 2 type bonding and weak sp type carbon nitrogen bonds and these bonds were found to increase with voltage. The fraction of sp 3-bonded species in the sample increased in low voltage range and after reaching maximum at 350 V, decreased for higher voltages. However, the concentration of sp 2 CN ring structures in the film increased with increasing voltage. Also, the peak width decreased at low voltages reaching a minimum and increased thereafter. It was observed that the voltage dependent increase in the concentration of polymeric type sp 2 CN (chain) structures was much more pronounced than that of graphitic type sp 2 CN (ring) structures. Raman spectra showed the presence of both the D and G bands. The shift in the G band indicated the presence of nitrogen in the film. The I D/I G ratio was found to increase with the incorporation of nitrogen. Auger electron spectroscopy (AES) showed a clear increase in the nitrogen content with increase in the voltage. The formation of the film could be explained on the basis of dissociation of electrolyte under applied voltage.

  8. Low voltage electrodeposition of CN {sub x} films and study of the effect of the deposition voltage on bonding configurations

    Energy Technology Data Exchange (ETDEWEB)

    Sreejith, K. [Novel Materials and Structural Chemistry Division, Bhabha Atomic Research Centre, Trombay, Mumbai 400 085 (India); Nuwad, J. [Novel Materials and Structural Chemistry Division, Bhabha Atomic Research Centre, Trombay, Mumbai 400 085 (India); Pillai, C.G.S. [Novel Materials and Structural Chemistry Division, Bhabha Atomic Research Centre, Trombay, Mumbai 400 085 (India)]. E-mail: cgspil@apsara.barc.ernet.in

    2005-10-15

    Carbon nitride (CN {sub x}) films were deposited from acetonitrile at low voltage (150-450 V) through electrodeposition. The films were characterized by atomic force microscopy (AFM), Raman spectroscopy and Fourier transform infrared (FT-IR) spectroscopy. AFM investigations revealed that the grain size was {approx}200 nm and roughness was {approx}10 nm. The films were found to be continuous and close packed. IR spectra revealed existence of strong sp{sup 3}, sp{sup 2} type bonding and weak sp type carbon nitrogen bonds and these bonds were found to increase with voltage. The fraction of sp{sup 3}-bonded species in the sample increased in low voltage range and after reaching maximum at 350 V, decreased for higher voltages. However, the concentration of sp{sup 2} CN ring structures in the film increased with increasing voltage. Also, the peak width decreased at low voltages reaching a minimum and increased thereafter. It was observed that the voltage dependent increase in the concentration of polymeric type sp{sup 2} CN (chain) structures was much more pronounced than that of graphitic type sp{sup 2} CN (ring) structures. Raman spectra showed the presence of both the D and G bands. The shift in the G band indicated the presence of nitrogen in the film. The I{sub D}/I{sub G} ratio was found to increase with the incorporation of nitrogen. Auger electron spectroscopy (AES) showed a clear increase in the nitrogen content with increase in the voltage. The formation of the film could be explained on the basis of dissociation of electrolyte under applied voltage.

  9. Design of Configurable Resistance Divider Type DAC-PUF Circuit%可配置电阻分压型DAC-PUF电路设计

    Institute of Scientific and Technical Information of China (English)

    汪鹏君; 李刚; 钱浩宇

    2016-01-01

    Physical Unclonable Functions (PUF)exploits process variation across same structure and design parameter unit circuits during the manufacturing processes to generate numerous unique,random and unclonable security keys.In this pa-per,a configurable resistance divider type DAC-PUF scheme is proposed,which consists of input register,resistor-string based DAC,voltage comparator and timing control module.After configuring the DAC cell by applying input challenges,the PUF circuit updates keys without physically replacement.In TSMC-LP 65 nm CMOS technology,the layout occupies 72. 4μm × 87. 8μm with custom designing.Experimental results show that the PUF circuit possesses nice statistical characteristic of u-niqueness,high randomness of 99. 1%and high stability of 97. 8%,both with respect to supply voltage variation from 1. 08V to 1. 32V,and temperature variation from -40℃to 125℃.It can be effectively used in information security field.%物理不可克隆函数(Physical Unclonable Function,PUF)电路利用结构和设计参数相同的单元电路在制造过程中存在的随机工艺偏差,产生具有唯一性、随机性和不可克隆性的密钥.通过对电阻失配和数模转换器(Digital to Analogue Conversion,DAC)的研究,提出一种可配置电阻分压型DAC-PUF电路设计方案.该PUF电路由输入寄存器、电阻分压型DAC、电压比较器和时序控制模块构成.通过激励信号配置DAC单元,使该PUF电路无需更换硬件便可实现输出密钥的变化.在TSMC-LP 65 nm CMOS工艺下采用全定制方式进行版图设计,面积为72.4μm ×87.8μm.实验结果表明该PUF电路唯一性高,且在不同温度(-40~125℃)和电压(1.08~1.32V)下随机性和可靠性分别大于99.1%和97.8%,可广泛应用于信息安全领域.

  10. Analogue Divider by Averaging a Triangular Wave

    Science.gov (United States)

    Selvam, Krishnagiri Chinnathambi

    2017-08-01

    A new analogue divider circuit by averaging a triangular wave using operational amplifiers is explained in this paper. The triangle wave averaging analog divider using operational amplifiers is explained here. The reference triangular waveform is shifted from zero voltage level up towards positive power supply voltage level. Its positive portion is obtained by a positive rectifier and its average value is obtained by a low pass filter. The same triangular waveform is shifted from zero voltage level to down towards negative power supply voltage level. Its negative portion is obtained by a negative rectifier and its average value is obtained by another low pass filter. Both the averaged voltages are combined in a summing amplifier and the summed voltage is given to an op-amp as negative input. This op-amp is configured to work in a negative closed environment. The op-amp output is the divider output.

  11. Numerical Electric Field Analysis of Power Status Sensor Observing Power Distribution System Taking into Account Voltage Divider Measurement Circuit

    Science.gov (United States)

    Kubo, Takuro; Furukawa, Tatsuya; Itoh, Hideaki; Fukumoto, Hisao; Wakuya, Hiroshi; Ohchi, Masashi

    We have proposed and preproducted the voltage-current waveform sensor of resin molded type for measuring the power factor and harmonics in power distribution systems. We have executed numerical electromagnetic analyses using the finite element method to estimate the characteristics and behaviours of the sensor. Although the magnetic field analyses for the current sensor have involved the measurement circuit, the electric field analyses have not included the measurement circuit for measuring voltage waveforms of power lines. In this paper, we describe the electric field analyses with the measurement circuit and prove the insulating strength of the proposed sensor permissible to the use in 22kV power distribution systems.

  12. Evaluation of higher distribution and/or utilization voltages. Fourth interim report (August 1980): assessment of optimum distribution configuration

    Energy Technology Data Exchange (ETDEWEB)

    1981-04-01

    This interim report provides documentation on the fourth task, Assessment of Optimum Distribution Configuration, of DOE Contract No. ET-78-C-01-2866, Evaluation of Higher Distribution and/or Utilization Voltages. The work performed under this task includes the development of a computer model for assessment of life cycle costs for the distribution and utilization systems, the development of an optimization algorithm to enable distribution system configuration optimization and a net energy analysis to determine potential net energy savings. Input data for this task derive from Task 3. The major output of this task is a documented computer code.

  13. Influence of the representation of the distribution transformer core configuration on voltages developed during unbalanced operations

    OpenAIRE

    Vernieri, Julieta Z.; Barbieri, María Beatriz; Arnera, Patricia L.

    2001-01-01

    The object of this paper is to emphasize the importance of the representation of the core configuration when seeking transients developed in a distribution transformer under an unbalanced situation. Digital time-domain simulations are performed with the Alternative Transients Program (ATP) for the case of a distribution three-phase transformer using the following two core configuration representations available in the ATP: three-legged core form and fivelegged core. Severe overvoltages ...

  14. MOSFET-based high voltage double square-wave pulse generator with an inductive adder configuration

    Energy Technology Data Exchange (ETDEWEB)

    Zhao, Xin [State Key Laboratory of Electrical Insulation and Power Equipment, Xi' an Jiaotong University, Xi' an 710049 (China); Zhang, Qiaogen, E-mail: hvzhang@mail.xjtu.edu.cn [State Key Laboratory of Electrical Insulation and Power Equipment, Xi' an Jiaotong University, Xi' an 710049 (China); Long, Jinghua [College of Physics, Shenzhen University, Shenzhen 518060 (China); Lei, Yunfei; Liu, Jinyuan [Institute of Optoelectronics, Shenzhen University, Shenzhen 518060 (China)

    2015-09-01

    This paper presents a fast MOSFET-based solid-state pulse generator for high voltage double square-wave pulses. The generator consists mainly of an inductive adder system stacked of 20 solid-state modules. Each of the modules has 18 power MOSFETs in parallel, which are triggered by individual drive circuits; these drive circuits themselves are synchronously triggered by a signal from avalanche transistors. Our experiments demonstrate that the output pulses with amplitude of 8.1 kV and peak current of about 405 A are available at a load impedance of 20 Ω. The pulse has a double square-wave form with a rise and fall time of 40 ns and 26 ns, respectively and bottom flatness better than 12%. The interval time of the double square-wave pulses can be adjustable by varying the interval time of the trigger pulses.

  15. Voltage-Controlled Floating Resistor Using DDCC

    Directory of Open Access Journals (Sweden)

    M. Kumngern

    2011-04-01

    Full Text Available This paper presents a new simple configuration to realize the voltage-controlled floating resistor, which is suitable for integrated circuit implementation. The proposed resistor is composed of three main components: MOS transistor operating in the non-saturation region, DDCC, and MOS voltage divider. The MOS transistor operating in the non-saturation region is used to configure a floating linear resistor. The DDCC and the MOS transistor voltage divider are used for canceling the nonlinear component term of MOS transistor in the non-saturation region to obtain a linear current/voltage relationship. The DDCC is employed to provide a simple summer of the circuit. This circuit offers an ease for realizing the voltage divider circuit and the temperature effect that includes in term of threshold voltage can be compensated. The proposed configuration employs only 16 MOS transistors. The performances of the proposed circuit are simulated with PSPICE to confirm the presented theory.

  16. Remarkable reduction in the threshold voltage of pentacene-based thin film transistors with pentacene/CuPc sandwich configuration

    Directory of Open Access Journals (Sweden)

    Yi Li

    2014-06-01

    Full Text Available This study investigates the remarkable reduction in the threshold voltage (VT of pentacene-based thin film transistors with pentacene/copper phthalocyanine (CuPc sandwich configuration. This reduction is accompanied by increased mobility and lowered sub-threshold slope (S. Sandwich devices coated with a 5 nm layer of CuPc layer are compared with conventional top-contact devices, and results indicate that VT decreased significantly from −20.4 V to −0.2 V, that mobility increased from 0.18 cm2/Vs to 0.51 cm2/Vs, and that S was reduced from 4.1 V/dec to 2.9 V/dec. However, the on/off current ratio remains at 105. This enhanced performance could be attributed to the reduction in charge trap density by the incorporated CuPc layer. Results suggest that this method is simple and effectively generates pentacene-based organic thin film transistors with high mobility and low VT.

  17. Schottky bipolar I-MOS: An I-MOS with Schottky electrodes and an open-base BJT configuration for reduced operating voltage

    Science.gov (United States)

    Kannan, N.; Kumar, M. Jagadesh

    2017-04-01

    In this paper, we have proposed a novel impact ionization MOS (I-MOS) structure, called the Schottky bipolar I-MOS, with Schottky source and drain electrodes and utilizing the open-base bipolar junction transistor (BJT) configuration for achieving reduction in the operating voltage of the I-MOS transistor. We report, using 2-D simulations, a low operating voltage (∼1.1 V) and a low subthreshold swing (∼3.6 mV/Decade). For the corresponding p-i-n I-MOS, the operating voltage is ∼5.5 V. The operating voltage of the Schottky bipolar I-MOS is the lowest reported operating voltage for silicon based I-MOS transistors. The nearly 80% reduction in the operating voltage of the Schottky bipolar I-MOS makes it suitable for applications requiring low operating voltages. The Schottky bipolar I-MOS is also expected to have an improved reliability over the p-i-n I-MOS since high energy carriers, induced by impact ionization near the drain, do not have to pass under the gate region in the channel. The use of Schottky contacts instead of heavily doped source and drain regions and the low channel doping level reduces the required thermal budget for device fabrication. The low operating voltage, low subthreshold swing and possibly improved reliability of the Schottky bipolar I-MOS, makes it a potential solution for applications where steep subthreshold slope transistors are being explored as alternative to the conventional MOS transistor.

  18. Resistor divider for high voltage pulse measurement in vacuum%一种在真空中测量脉冲高电压的电阻分压器

    Institute of Scientific and Technical Information of China (English)

    卫兵; 关永超; 卿燕玲; 陈林; 周良骥; 李晔; 丰树平

    2012-01-01

    A resistor divider has been designed for voltage measurement of diode load for 1 MV/100 kA fast linear transformer driver(LTD). The divider is designed with two stages. The primary stage is a column of alternating annular metal grading rings and tapered insulators enclosing a resistive solution of sodium thiosulfate. A middle electrode is connected to the secondary voltage dividing stage. There is a 4 kΩ resistor in series with the 50 Ω input impedance of the attenuator or oscilloscope. The e-quivalent circuit of the divider which includes distributed capacitance and inductance has been calculated. It indicates that the high frequency limit of the divider is about 200 MHz. The divider has been calibrated in-situ using a P6015A probe and a high voltage pulser. The calibration ratio is 5 400 : 1. The voltage of diode load reaches 1. 08 MV when the charging voltage of LTD stage is ±85 kV respectively, according with the simulation of LTD.%为测量快脉冲直线变压器驱动源(LTD)二极管负载的脉冲高电压,设计了在真空环境中使用的电阻分压器.分压器使用绝缘堆结构,采用静电场模拟分析了分压器的电场分布.建立了包含分布参数的等效电路,并进行了频率响应仿真,可得分压器的频响上限为200 MHz.使用标准高压探头对分压器进行在线标定,分压比标定结果为5 400∶1,与设计值相符合.在LTD调试实验中,模块充电85 kV时二极管电压为1.08 MV,与理论估算结果一致.

  19. Numerical and experimental study of the mesa configuration in high-voltage 4H-SiC PiN rectifiers

    Science.gov (United States)

    Deng, Xiao-Chuan; Chen, Xi-Xi; Li, Cheng-Zhan; Shen, Hua-Jun; Zhang, Jin-Ping

    2016-08-01

    The effect of the mesa configuration on the reverse breakdown characteristic of a SiC PiN rectifier for high-voltage applications is analyzed in this study. Three geometrical parameters, i.e., mesa height, mesa angle and mesa bottom corner, are investigated by numerical simulation. The simulation results show that a deep mesa height, a small mesa angle and a smooth mesa bottom (without sub-trench) could contribute to a high breakdown voltage due to a smooth and uniform surface electric field distribution. Moreover, an optimized mesa structure without sub-trench (mesa height of 2.2 μm and mesa angle of 20°) is experimentally demonstrated. A maximum reverse blocking voltage of 4 kV and a forward voltage drop of 3.7 V at 100 A/cm2 are obtained from the fabricated diode with a 30-μm thick N- epi-layer, corresponding to 85% of the ideal parallel-plane value. The blocking characteristic as a function of the JTE dose is also discussed for the PiN rectifiers with and without interface charge. Project supported by the State Key Program of the National Natural Science Foundation of China (Grant No. 61234006), the Open Foundation of the State Key Laboratory of Electronic Thin Films and Integrated Devices, China (Grant No. KFJJ201301), and the National Science and Technology Major Project of the Ministry of Science and Technology, China (Grant No. 2013ZX02305-003).

  20. Dividing Discipline

    DEFF Research Database (Denmark)

    Kristensen, Peter Marcus

    2012-01-01

    the periphery of the network—security studies and international political economy in particular—but communication is also divided along the lines of geography and policy/theory. The article concludes that divisions notwithstanding, IR communication remains centered around American, general, and theoretical IR...

  1. Experimental investigation of an optimum configuration for a high-voltage photoemission gun for operation at ≥500 kV

    Science.gov (United States)

    Nishimori, Nobuyuki; Nagai, Ryoji; Matsuba, Shunya; Hajima, Ryoichi; Yamamoto, Masahiro; Honda, Yosuke; Miyajima, Tsukasa; Iijima, Hokuto; Kuriki, Masao; Kuwahara, Makoto

    2014-05-01

    We demonstrated the generation of a 500-keV electron beam from a high dc voltage photoemission gun for an energy recovery linac light source [N. Nishimori et al., Appl. Phys. Lett. 102, 234103 (2013)]. This demonstration was achieved by addressing two discharge problems that lead to vacuum breakdown in the dc gun. One is field emission generated from a central stem electrode. We employed a segmented insulator to protect the ceramic insulator surface from the field emission. The other is microdischarge at an anode electrode or a vacuum chamber, which is triggered by microparticle transfer or field emission from a cathode electrode. An experimental investigation revealed that a larger acceleration gap, optimized mainly to reduce the surface electric field of the anode electrode, suppresses the microdischarge events that accompany gas desorption. It was also found that nonevaporable getter pumps placed around the acceleration gap greatly help to suppress those microdischarge events. The applied voltage as a function of the total gas desorption is shown to be a good measure for finding the optimum dc gun configuration.

  2. Dividing Discipline

    DEFF Research Database (Denmark)

    Kristensen, Peter Marcus

    2012-01-01

    International Relations (IR) has cultivated an image as a discipline with strong divisions along paradigmatic, methodological, metatheoretical, geographical, and other lines. This article questions that image analyzing the latent structures of communication in IR. It uses citation data from more...... the periphery of the network—security studies and international political economy in particular—but communication is also divided along the lines of geography and policy/theory. The article concludes that divisions notwithstanding, IR communication remains centered around American, general, and theoretical IR...

  3. Over-voltage protection system and method

    Energy Technology Data Exchange (ETDEWEB)

    Chi, Song; Dong, Dong; Lai, Rixin

    2017-05-02

    An over-voltage protection system includes an electronic valve connected across two terminals of a circuit and an over-voltage detection circuit connected across one of the plurality of semiconductor devices for detecting an over-voltage across the circuit. The electronic valve includes a plurality of semiconductor devices connected in series. The over-voltage detection circuit includes a voltage divider circuit connected to a break-over diode in a way to provide a representative low voltage to the break-over diode and an optocoupler configured to receive a current from the break-over diode when the representative low voltage exceeds a threshold voltage of the break-over diode indicating an over-voltage condition. The representative low voltage provided to the break-over diode represents a voltage across the one semiconductor device. A plurality of self-powered gate drive circuits are connected to the plurality of semiconductor devices, wherein the plurality of self-powered gate drive circuits receive over-voltage triggering pulses from the optocoupler during the over-voltage condition and switch on the plurality of semiconductor devices to bypass the circuit.

  4. Mobility Divides

    DEFF Research Database (Denmark)

    Jensen, Ole B.

    Contemporary mobilities are cultural and social manifestations, and the mobile practices in the everyday life of billions of humans are re-configuring senses of place, self, other and relationships to the built environment. The way ‘mobile situations’ are staged in designed and built environments...... are increasingly becoming ‘second nature’ but also expressions of power, exclusion, and difference. In this talk I will be applying a perspective of ‘mobile situationism’ illustrating how mobile everyday life practices are staged ‘from above’ in planning and policy frameworks, design codes and architectural...... designs, but also how the situated and embodied mobile everyday life practices are staged ‘from below’ in concrete acts of choice concerning modes of mobilities, ways of moving and interacting. The ‘staging mobilites’ framework opens up to an understanding of the meaning of ‘mobilities design...

  5. Mobility Divides

    DEFF Research Database (Denmark)

    Jensen, Ole B.

    Contemporary mobilities are cultural and social manifestations, and the mobile practices in the everyday life of billions of humans are re-configuring senses of place, self, other and relationships to the built environment. The way ‘mobile situations’ are staged in designed and built environments...... are increasingly becoming ‘second nature’ but also expressions of power, exclusion, and difference. In this talk I will be applying a perspective of ‘mobile situationism’ illustrating how mobile everyday life practices are staged ‘from above’ in planning and policy frameworks, design codes and architectural...... designs, but also how the situated and embodied mobile everyday life practices are staged ‘from below’ in concrete acts of choice concerning modes of mobilities, ways of moving and interacting. The ‘staging mobilites’ framework opens up to an understanding of the meaning of ‘mobilities design...

  6. 分壁塔与常规重整生成油分离工艺流程模拟比较%SIMULATIVE COMPARISON OF PROCESS FLOWS FOR THE SEPARATION OF REFORMATE INCLUDING DIVIDING WALL COLUMN AND CONVENTIONAL CONFIGURATIONS

    Institute of Scientific and Technical Information of China (English)

    刘传强; 邵文; 李小娜; 何勇

    2011-01-01

    On the basis of reformate data from a CCR-aromatics complex unit, two process flows in cluding a dividing wall column(DWC) configuration and a conventional two-column configuration for the separation of reformate are simulated by PRO Ⅱ software and compared under obtaining the same quali ties of products.It is concluded that compared with the conventional two-column process flow for DWC process flow the reductions of energy consumption,equipment investment cost and area occupation are approximately 31.2% ,20.3% and 38.3%,respectively.%利用PROⅡ流程模拟软件分别对采用常规两塔工艺流程和分壁塔工艺流程的两种重整生成油分离方案进行模拟,以连续重整-芳烃联合装置的重整生成油为原料,在保证分离产品质量一致的情况下,从能耗、设备投资和占地的角度分析对比两种方案的优劣.结果表明,与常规两塔工艺流程相比,分壁塔流程的能耗降低31.2%,设备投资节省20.3%,占地面积减少38.3%.

  7. 农用高压电网圆柱形殷钢电容分压器边缘效应的研究%Application Study of Agricultural High-voltage Grid of Cylindrical Invar on Capacitive Divider Edge Effects

    Institute of Scientific and Technical Information of China (English)

    董赫; 李伟凯

    2015-01-01

    By comparing the calculated value and actual measurement value of invar on the capacitive voltage divider,the presence of edge effects caused the actual results was too large capacitive divider conclusions. The theoretical analysis was used as a starting point and combined with calculus theory and capacitors idea,and the edge effects formula of the total capacitance value was derived. According to the characteristics of the cylindrical capacitor,the approach of increasing the capacitive divider edge capacitance on the ring chamfer radius was provided to weaken the edge effect,and the test had been passed to verify the program feasibility.%通过殷钢电容分压器理论计算值与实际测量值的对比,得到边缘效应的存在导致电容分压器的实际测量值偏大的结论。以理论分析为切入点,结合微积分原理及电容串联思想,推导出计及边缘效应的分压器电容值计算公式。针对圆柱形电容器的特点,提出利用增加电容分压器边缘电容环倒角半径的方法来削弱边缘效应,并通过试验验证了该方案的可行性。

  8. Graphene-coated hollow fiber membrane as the cathode in anaerobic electrochemical membrane bioreactors – Effect of configuration and applied voltage on performance and membrane fouling

    KAUST Repository

    Werner, Craig M.

    2015-12-22

    Electrically conductive, graphene-coated hollow-fiber porous membranes were used as cathodes in anaerobic electrochemical membrane bioreactors (AnEMBRs) operated at different applied voltages (0.7 V and 0.9 V) using a new rectangular reactor configuration, compared to a previous tubular design (0.7 V). The onset of biofouling was delayed and minimized in rectangular reactors operated at 0.9 V, compared to those at 0.7 V due to higher rates of hydrogen production. Maximum transmembrane pressures for the rectangular reactor were only 0.10 bar (0.7 V) or 0.05 bar (0.9 V) after 56 days of operation, compared to 0.46 bar (0.7 V) for the tubular reactor after 52 days. The thickness of the membrane biofouling layer was approximately 0.4 µm for rectangular reactors and 4 µm for the tubular reactor. Higher permeate quality (TSS = 0.05 mg/L) was achieved in the rectangular AnEMBR than the tubular AnEMBR (TSS = 17 mg/L), likely due to higher current densities that minimized the accumulation of cells in suspension. These results show that the new rectangular reactor design, which had increased rates of hydrogen production, successfully delayed the onset of cathode biofouling and improved reactor performance.

  9. The impact of P(NDI2OD-T2 crystalline domains on the open-circuit voltage of bilayer all-polymer solar cells with an inverted configuration

    Directory of Open Access Journals (Sweden)

    Yu Jin Kim

    2015-12-01

    Full Text Available We fabricated P(NDI2OD-T2/PTB7 bilayer all-polymer solar cells with an inverted configuration, where the annealing temperature was systematically varied. The current density–voltage behavior was investigated and the structural properties of the P(NDI2OD-T2 layers were characterized. Absorption spectroscopy, surface morphology, and crystallite analysis showed that increasing phase segregation of P(NDI2OD-T2 films occurred as the annealing temperature increased. We found that, as the P(NDI2OD-T2 stacking improved, with larger domains, the open-circuit voltage decreased and the saturation dark current density increased. This work provides a guide for the processing of P(NDI2OD-T2 layers to maximize the power conversion efficiency of all-polymer solar cells.

  10. Mono-Heteromeric Configurations of Gap Junction Channels Formed by Connexin43 and Connexin45 Reduce Unitary Conductance and Determine both Voltage Gating and Metabolic Flux Asymmetry

    Directory of Open Access Journals (Sweden)

    Guoqiang Zhong

    2017-05-01

    Full Text Available In cardiac tissues, the expression of multiple connexins (Cx40, Cx43, Cx45, and Cx30.2 is a requirement for proper development and function. Gap junctions formed by these connexins have distinct permeability and gating mechanisms. Since a single cell can express more than one connexin isoform, the formation of hetero-multimeric gap junction channels provides a tissue with an enormous repertoire of combinations to modulate intercellular communication. To study further the perm-selectivity and gating properties of channels containing Cx43 and Cx45, we studied two monoheteromeric combinations in which a HeLa cell co-transfected with Cx43 and Cx45 was paired with a cell expressing only one of these connexins. Macroscopic measurements of total conductance between cell pairs indicated a drastic reduction in total conductance for mono-heteromeric channels. In terms of Vj dependent gating, Cx43 homomeric connexons facing heteromeric connexons only responded weakly to voltage negativity. Cx45 homomeric connexons exhibited no change in Vj gating when facing heteromeric connexons. The distributions of unitary conductances (γj for both mono-heteromeric channels were smaller than predicted, and both showed low permeability to the fluorescent dyes Lucifer yellow and Rhodamine123. For both mono-heteromeric channels, we observed flux asymmetry regardless of dye charge: flux was higher in the direction of the heteromeric connexon for MhetCx45 and in the direction of the homomeric Cx43 connexon for MhetCx43. Thus, our data suggest that co-expression of Cx45 and Cx43 induces the formation of heteromeric connexons with greatly reduced permeability and unitary conductance. Furthermore, it increases the asymmetry for voltage gating for opposing connexons, and it favors asymmetric flux of molecules across the junction that depends primarily on the size (not the charge of the crossing molecules.

  11. Continental Divide Trail

    Data.gov (United States)

    Earth Data Analysis Center, University of New Mexico — This shapefile was created to show the proximity of the Continental Divide to the Continental Divide National Scenic Trail in New Mexico. This work was done as part...

  12. Software configuration management

    CERN Document Server

    Keyes, Jessica

    2004-01-01

    Software Configuration Management discusses the framework from a standards viewpoint, using the original DoD MIL-STD-973 and EIA-649 standards to describe the elements of configuration management within a software engineering perspective. Divided into two parts, the first section is composed of 14 chapters that explain every facet of configuration management related to software engineering. The second section consists of 25 appendices that contain many valuable real world CM templates.

  13. Electronically configured battery pack

    Energy Technology Data Exchange (ETDEWEB)

    Kemper, D.

    1997-03-01

    Battery packs for portable equipment must sometimes accommodate conflicting requirements to meet application needs. An electronically configurable battery pack was developed to support two highly different operating modes, one requiring very low power consumption at a low voltage and the other requiring high power consumption at a higher voltage. The configurable battery pack optimizes the lifetime and performance of the system by making the best use of all available energy thus enabling the system to meet its goals of operation, volume, and lifetime. This paper describes the cell chemistry chosen, the battery pack electronics, and tradeoffs made during the evolution of its design.

  14. International Divider Walls

    NARCIS (Netherlands)

    Kruis, A.; Sneller, A.C.W.(L.)

    2013-01-01

    The subject of this teaching case is the Enterprise Resource Planning (ERP) system implementation at International Divider Walls, the world market leader in design, production, and sales of divider walls. The implementation in one of the divisions of this multinational company had been successful, a

  15. International Divider Walls

    NARCIS (Netherlands)

    Kruis, A.; Sneller, A.C.W.(L.)

    2013-01-01

    The subject of this teaching case is the Enterprise Resource Planning (ERP) system implementation at International Divider Walls, the world market leader in design, production, and sales of divider walls. The implementation in one of the divisions of this multinational company had been successful,

  16. Development of a New Cascade Voltage-Doubler for Voltage Multiplication

    OpenAIRE

    Arash Toudeshki; Norman Mariun; Hashim Hizam; Noor Izzri Abdul Wahab

    2014-01-01

    For more than eight decades, cascade voltage-doubler circuits are used as a method to produce DC output voltage higher than the input voltage. In this paper, the topological developments of cascade voltage-doublers are reviewed. A new circuit configuration for cascade voltage-doubler is presented. This circuit can produce a higher value of the DC output voltage and better output quality compared to the conventional cascade voltage-doubler circuits, with the same number of stages.

  17. Bridging the Digital Divide

    DEFF Research Database (Denmark)

    Frølunde, Lisbeth

    2002-01-01

    The article concerns the digital divide, meaning the social inequity in the access and the opportunities for gaining competencies with ICT (information and communication technologies). Problematic issues are highlighted in relation to experiences during visits to several Computer Clubhouses...

  18. The Open Access Divide

    National Research Council Canada - National Science Library

    Jingfeng Xia

    2013-01-01

      This paper is an attempt to review various aspects of the open access divide regarding the difference between those academics who support free sharing of data and scholarly output and those academics who do...

  19. Low-voltage p entacene photo detector based on a vertical transistor configuration%基于垂直晶体管结构的低电压并五苯光电探测器∗

    Institute of Scientific and Technical Information of China (English)

    杨丹; 张丽; 杨盛谊; 邹炳锁

    2015-01-01

    Due to the excellent characteristics of field-effect transistor and its high absorption coefficient in the visible region, pentacene has been widely used in phototransistors. The channel length of the vertical transistor could be designed to be very short (on the order of nanometers). In this way, the device performances and its working frequency can be effectively improved, and the energy consumption can be reduced simultaneously. In this paper, we fabricate a kind of low-voltage pentacene photodetector ITO(S)/Pentacene/Al(G)/Pentacene/Au(D), based on the vertical transistor configuration. The threshold voltage and “on/off” current ratio are −0.9 V and 104 at a low working-voltage of −3 V, respectively. The pentacene photodetector ITO/Pentacene(80 nm)/Al(15 nm)/Pentacene (80 nm)/Au exhibits a good p-type transistor behavior and low-voltage-controlling performance. The photosensitivity and responsivity vary with incident monochromatic light from 350 nm to 750 nm, and the photosensitivity peak of 308 is obtained at 350 nm with a responsivity of 219 mA·W−1, which is even higher than that of the standard Si-based photodetector under 350 nm incident light. Therefore, this work provides an easy way to fabricate a high sensitivity all-organic photodetector working at low voltages.%并五苯(Pentacene)具有优良的场效应晶体管特性及在可见光区的高吸收系数,被广泛应用于光敏(电)晶体管中.垂直晶体管的沟道长度可做到纳米量级,能有效提高器件的性能和工作频率,同时降低能耗.本文制备了一种基于垂直晶体管结构的低电压并五苯光电探测器ITO(S)/Pentacene/Al(G)/Pentacene/Au(D).实验发现,在工作电压低至−3 V时,并五苯光电探测器ITO/Pentacene (80 nm)/Al(15 nm)/ Pentacene(80 nm)/Au 的阈值电压为−0.9 V,“开/关”电流比为104,表现出了良好的P型晶体管特性以及低电压调控性能.在350—750 nm的不同波长单色光照射下,器件的“明/暗

  20. Stray voltage mitigation

    Energy Technology Data Exchange (ETDEWEB)

    Jamali, B.; Piercy, R.; Dick, P. [Kinetrics Inc., Toronto, ON (Canada). Transmission and Distribution Technologies

    2008-04-09

    This report discussed issues related to farm stray voltage and evaluated mitigation strategies and costs for limiting voltage to farms. A 3-phase, 3-wire system with no neutral ground was used throughout North America before the 1930s. Transformers were connected phase to phase without any electrical connection between the primary and secondary sides of the transformers. Distribution voltage levels were then increased and multi-grounded neutral wires were added. The earth now forms a parallel return path for the neutral current that allows part of the neutral current to flow continuously through the earth. The arrangement is responsible for causing stray voltage. Stray voltage causes uneven milk production, increased incidences of mastitis, and can create a reluctance to drink water amongst cows when stray voltages are present. Off-farm sources of stray voltage include phase unbalances, undersized neutral wire, and high resistance splices on the neutral wire. Mitigation strategies for reducing stray voltage include phase balancing; conversion from single to 3-phase; increasing distribution voltage levels, and changing pole configurations. 22 refs., 5 tabs., 13 figs.

  1. Information configuration?

    OpenAIRE

    Lauro Cesar Araujo; Mamede Lima-Marques

    2016-01-01

    Introduction: The term "configuration information" has emerged in the works of Information Architecture; however, there isn’t a conceptualization of “configuration” within Information Architecture. Objective: The objective is propose a definition for "configuration" and "information configuration" within the Information Architecture discipline, and indicate a teleological corpus from configuration management that can be used as paxis in Information Architecture. Methodolo...

  2. The Open Access Divide

    Directory of Open Access Journals (Sweden)

    Jingfeng Xia

    2013-10-01

    Full Text Available This paper is an attempt to review various aspects of the open access divide regarding the difference between those academics who support free sharing of data and scholarly output and those academics who do not. It provides a structured description by adopting the Ws doctrines emphasizing such questions as who, what, when, where and why for information-gathering. Using measurable variables to define a common expression of the open access divide, this study collects aggregated data from existing open access as well as non-open access publications including journal articles and extensive reports. The definition of the open access divide is integrated into the discussion of scholarship on a larger scale.

  3. A dividing issue

    DEFF Research Database (Denmark)

    Gamborg, Christian; Jensen, Frank Søndergaard; Sandøe, Peter

    2016-01-01

    . While there was broad agreement across all three groups that recreational hunting of naturally occurring “surplus” wildlife is acceptable, the release of farm-reared game birds for shooting was a dividing issue, both within the groups and between them. The majority of participants (51%) in the survey...

  4. Divide and Pacify

    DEFF Research Database (Denmark)

    Vanhuysse, Pieter

    by pointing to deeper political motives and wider sociological consequences. Divide and Pacify was nominated for the American Sociological Association's Award for Distinguished Contribution to Scholarship 2006, Section on Political Sociology. Praise and reviews: "Pieter Vanhuysse…is a political scientist...... across many settings in which democratic governments face the task of implementing costly reforms in complex and uncertain policy environments." –János Kornai, Harvard University "Divide and Pacify contains a provocative thesis about the manner in which political strategy was used to consolidate...... policy." - Kenneth Shepsle, Professor, Harvard University and Fellow, American Academy of Sciences "In post-communist Europe, international advice—for example from the International Monetary Fund and the World Bank—to reforming governments focused heavily on economic policy. The political imperative...

  5. Voltage Swells Improvement in Low Voltage Network Using Dynamic Voltage Restorer

    Directory of Open Access Journals (Sweden)

    R. Omar

    2011-01-01

    Full Text Available Problem statement: Voltage disturbances are the most common power quality problem due to the increased use of a large numbers of sophisticated electronic equipment in industrial distribution system. The voltage disturbances such as voltage sags, swells, harmonics, unbalance and flickers. High quality in the power supply is needed, since failures due to such disturbances usually have a high impact on production cost. There are many different solutions to compensate voltage disturbances but the use of a DVR is considered to be the most cost effective method. The objective of this study is to propose a new topology of a DVR in order to mitigate voltage swells using a powerful power custom device namely the Dynamic Voltage Restorer (DVR. Approach: New configuration of a DVR with an improvement of a controller based on direct-quadrature-zero method has been introduced to compensate voltage swells in the network. Results: The effectiveness of the DVR with its controller were verify using Matlab/Simulinks SimPower Toolbox and then implemented using 5KVA DVR experimental setup. Simulations and experimental results demonstrate the effective dynamic performance of the proposed configuration. Conclusion: The implimentation of the proposed DVR validate the capabilities in mitigating of voltage swells effectiveness.During voltage swells, the DVR injects an appropriate voltage to maintain the load voltage at its nominal value.

  6. Bridging the Digital Divide

    DEFF Research Database (Denmark)

    Frølunde, Lisbeth

    2002-01-01

    The article concerns the digital divide, meaning the social inequity in the access and the opportunities for gaining competencies with ICT (information and communication technologies). Problematic issues are highlighted in relation to experiences during visits to several Computer Clubhouses......, a network of multimedia workshops for youth in the USA. There are references to the learning philosophy Constructionism, which originates from MIT Media Lab and is the basis for the Computer Clubhouse project. Abstract : The consortium for Math and Science at Learning Lab Denmark and the Ministry...... of significant European initiatives promoting the recruitment and quality of the science and technology educations....

  7. CROSSING THE GREAT DIVIDE

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    The safety and quality standards divide is the most severe challenge facing China’s toy industry China was blamed a spate of toy recalls this year.Overseas customers and press pointed the finger at China’s toy makers who had manu- factured toys according to their con- tracts.It was later found that most of the toy problems came from design faults of brand holders,not from Chinese manufacturers. To Wei Chuangzhong,Vice Minister of the General Administration of Quality Supervision,Inspection and Quarantine (AQSIQ),the cavalcade of negative press coverage overseas has been unfair and bad for China’s manufacturers.

  8. Monitoring the Digital Divide

    Energy Technology Data Exchange (ETDEWEB)

    Cottrell, Les

    2003-05-28

    It is increasingly important to support the large numbers of scientists working in remote areas and having low bandwidth access to the Internet. This will continue to be the case for years to come since there is evidence from PingER performance measurements that the, so-called, digital divide is not decreasing. In this work, we review the collaborative work of The Abdus Salam International Center for Theoretical Physics (ICTP) in Trieste, a leading organization promoting science dissemination in the developing world- and SLAC in Stanford, to monitor by PingER, Universities and Research Institutions all over the developing world following the recent ''Recommendations of Trieste'' to help bridge the digital divide. As a result, PingER's deployment now covers the real-time monitoring of worldwide Internet performance and, in particular, West and Central Africa for the first time. We report on the results from the ICTP sites and quantitatively identify regions with poor performance, identify trends, discuss experiences and future work.

  9. Analyzing of Dynamic Voltage Restorer in Series Compensation Voltage

    Directory of Open Access Journals (Sweden)

    Naser Parhizgar

    2012-02-01

    Full Text Available The Dynamic Voltage Restorer (DVR is a series-connected compensator to generate a controllable voltage to against the short-term voltage disturbances. The technique of DVR is an effective and cost competitive approach to improve voltage quality at the load side. This study presents a single-phase and threephase DVR system with reduced switch-count topology to protect the sensitive load against abnormal voltage conditions. Most basic function, the DVR configuration consist of a two level Voltage Source Converter (VSC, a dc energy storage device, a coupling transformer Connected in shunt with the ac system This study presents the application of Dynamic Voltage Restorer (DVR on power distribution systems for mitigation of voltage sag at critical loads. DVR is one of the compensating types of custom power devices. The DVR, which is based on forced-commutated Voltage Source Converter (VSC has been proved suitable for the task of compensating voltage sags/swells. Simulation results are presented to illustrate and understand the performances of DVR in supporting load voltages under voltage sags/swells conditions.

  10. High voltage pulse generator

    Science.gov (United States)

    Fasching, George E.

    1977-03-08

    An improved high-voltage pulse generator has been provided which is especially useful in ultrasonic testing of rock core samples. An N number of capacitors are charged in parallel to V volts and at the proper instance are coupled in series to produce a high-voltage pulse of N times V volts. Rapid switching of the capacitors from the paralleled charging configuration to the series discharging configuration is accomplished by using silicon-controlled rectifiers which are chain self-triggered following the initial triggering of a first one of the rectifiers connected between the first and second of the plurality of charging capacitors. A timing and triggering circuit is provided to properly synchronize triggering pulses to the first SCR at a time when the charging voltage is not being applied to the parallel-connected charging capacitors. Alternate circuits are provided for controlling the application of the charging voltage from a charging circuit to be applied to the parallel capacitors which provides a selection of at least two different intervals in which the charging voltage is turned "off" to allow the SCR's connecting the capacitors in series to turn "off" before recharging begins. The high-voltage pulse-generating circuit including the N capacitors and corresponding SCR's which connect the capacitors in series when triggered "on" further includes diodes and series-connected inductors between the parallel-connected charging capacitors which allow sufficiently fast charging of the capacitors for a high pulse repetition rate and yet allow considerable control of the decay time of the high-voltage pulses from the pulse-generating circuit.

  11. High Voltage Charge Pump

    KAUST Repository

    Emira, Ahmed A.

    2014-10-09

    Various embodiments of a high voltage charge pump are described. One embodiment is a charge pump circuit that comprises a plurality of switching stages each including a clock input, a clock input inverse, a clock output, and a clock output inverse. The circuit further comprises a plurality of pumping capacitors, wherein one or more pumping capacitors are coupled to a corresponding switching stage. The circuit also comprises a maximum selection circuit coupled to a last switching stage among the plurality of switching stages, the maximum selection circuit configured to filter noise on the output clock and the output clock inverse of the last switching stage, the maximum selection circuit further configured to generate a DC output voltage based on the output clock and the output clock inverse of the last switching stage.

  12. Why do bacteria divide?

    Directory of Open Access Journals (Sweden)

    Vic eNorris

    2015-04-01

    Full Text Available The problem of not only how but also why cells divide can be tackled using recent ideas. One idea from the origins of life – Life as independent of its constituents – is that a living entity like a cell is a particular pattern of connectivity between its constituents. This means that if the growing cell were just to get bigger the average connectivity between its constituents per unit mass – its cellular connectivity – would decrease and the cell would lose its identity. The solution is division which restores connectivity. The corollary is that the cell senses decreasing cellular connectivity and uses this information to trigger division. A second idea from phenotypic diversity – Life on the Scales of Equilibria – is that a bacterium must find strategies that allow it to both survive and grow. This means that it has learnt to reconcile the opposing constraints that these strategies impose. The solution is that the cell cycle generates daughter cells with different phenotypes based on sufficiently complex equilibrium and non-equilibrium cellular compounds and structures appropriate for survival and growth, respectively, alias `hyperstructures'. The corollary is that the cell senses both the quantity of equilibrium material and the intensity of use of non-equilibrium material and then uses this information to trigger the cell cycle. A third idea from artificial intelligence – Competitive Coherence – is that a cell selects the active subset of elements that actively determine its phenotype from a much larger set of available elements. This means that the selection of an active subset of a specific size and composition must be done so as to generate both a coherent cell state, in which the cell’s contents work together harmoniously, and a coherent sequence of cell states, each coherent with respect to itself and to an unpredictable environment. The solution is the use of a range of mechanisms ranging from hyperstructure dynamics

  13. Why do bacteria divide?

    Science.gov (United States)

    Norris, Vic

    2015-01-01

    The problem of not only how but also why cells divide can be tackled using recent ideas. One idea from the origins of life - Life as independent of its constituents - is that a living entity like a cell is a particular pattern of connectivity between its constituents. This means that if the growing cell were just to get bigger the average connectivity between its constituents per unit mass - its cellular connectivity - would decrease and the cell would lose its identity. The solution is division which restores connectivity. The corollary is that the cell senses decreasing cellular connectivity and uses this information to trigger division. A second idea from phenotypic diversity - Life on the Scales of Equilibria - is that a bacterium must find strategies that allow it to both survive and grow. This means that it has learnt to reconcile the opposing constraints that these strategies impose. The solution is that the cell cycle generates daughter cells with different phenotypes based on sufficiently complex equilibrium (E) and non-equilibrium (NE) cellular compounds and structures appropriate for survival and growth, respectively, alias 'hyperstructures.' The corollary is that the cell senses both the quantity of E material and the intensity of use of NE material and then uses this information to trigger the cell cycle. A third idea from artificial intelligence - Competitive Coherence - is that a cell selects the active subset of elements that actively determine its phenotype from a much larger set of available elements. This means that the selection of an active subset of a specific size and composition must be done so as to generate both a coherent cell state, in which the cell's contents work together harmoniously, and a coherent sequence of cell states, each coherent with respect to itself and to an unpredictable environment. The solution is the use of a range of mechanisms ranging from hyperstructure dynamics to the cell cycle itself.

  14. Parametric frequency dividers in satellite communications

    OpenAIRE

    Kosmopoulos, S. A.; Lo Forti, R.; Saggese, E.

    1990-01-01

    The performance of two different parametric frequency dividers, using GaAs varactor diodes in a balanced circuit configuration implemented by planar (microstrip) or quasi-planar (finline, coupled finline ) elements respectively, is presented. The almost phase noise free operation of these devices allows the construction of efficient miniature synthesizers or carrier recovering schemes, incorporated on the space segment of Ku- or Ka-band satellite communications systems.

  15. Wideband unbalanced waveguide power dividers and combiners

    Energy Technology Data Exchange (ETDEWEB)

    Halligan, Matthew; McDonald, Jacob Jeremiah; Strassner, II, Bernd H.

    2016-05-17

    The various technologies presented herein relate to waveguide dividers and waveguide combiners for application in radar systems, wireless communications, etc. Waveguide dividers-combiners can be manufactured in accordance with custom dimensions, as well as in accordance with waveguide standards such that the input and output ports are of a defined dimension and have a common impedance. Various embodiments are presented which can incorporate one or more septum(s), one or more pairs of septums, an iris, an input matching region, a notch located on the input waveguide arm, waveguide arms having stepped transformer regions, etc. The various divider configurations presented herein can be utilized in high fractional bandwidth applications, e.g., a fractional bandwidth of about 30%, and RF applications in the Ka frequency band (e.g., 26.5-40 GHz).

  16. Hypertext Configurations

    DEFF Research Database (Denmark)

    Finnemann, Niels Ole

    2016-01-01

    , links, interactive processes, and time scalings, and that the hypertext configuration is a major but not sole source of the messiness of big data. The notion of hypertext will be revalidated, placed at the center of the interpretation of networked digital media, and used in the analysis of the fast...

  17. Hypertext Configurations

    DEFF Research Database (Denmark)

    Finnemann, Niels Ole

    2016-01-01

    , links, interactive processes, and time scalings, and that the hypertext configuration is a major but not sole source of the messiness of big data. The notion of hypertext will be revalidated, placed at the center of the interpretation of networked digital media, and used in the analysis of the fast......The article presents a conceptual framework for distinguishing different sorts of heterogeneous digital materials. The hypothesis is that a wide range of heterogeneous data resources can be characterized and classified due to their particular configurations of hypertext features such as scripts......-growing amounts of heterogeneous digital collections, assemblages, and corpora. The introduction summarizes the wider background of a fast-changing data landscape....

  18. High-voltage picoamperemeter

    Energy Technology Data Exchange (ETDEWEB)

    Bugl, Andrea; Ball, Markus; Boehmer, Michael; Doerheim, Sverre; Hoenle, Andreas; Konorov, Igor [Technische Universitaet Muenchen, Garching (Germany); Ketzer, Bernhard [Technische Universitaet Muenchen, Garching (Germany); Helmholtz-Institut fuer Strahlen- und Kernphysik, Bonn (Germany)

    2014-07-01

    Current measurements in the nano- and picoampere region on high voltage are an important tool to understand charge transfer processes in micropattern gas detectors like the Gas Electron Multiplier (GEM). They are currently used to e.g. optimize the field configuration in a multi-GEM stack to be used in the ALICE TPC after the upgrade of the experiment during the 2nd long shutdown of the LHC. Devices which allow measurements down to 1pA at high voltage up to 6 kV have been developed at TU Muenchen. They are based on analog current measurements via the voltage drop over a switchable shunt. A microcontroller collects 128 digital ADC values and calculates their mean and standard deviation. This information is sent with a wireless transmitting unit to a computer and stored in a root file. A nearly unlimited number of devices can be operated simultaneously and read out by a single receiver. The results can also be displayed on a LCD directly at the device. Battery operation and the wireless readout are important to protect the user from any contact to high voltage. The principle of the device is explained, and systematic studies of their properties are shown.

  19. Electrical system architecture having high voltage bus

    Science.gov (United States)

    Hoff, Brian Douglas [East Peoria, IL; Akasam, Sivaprasad [Peoria, IL

    2011-03-22

    An electrical system architecture is disclosed. The architecture has a power source configured to generate a first power, and a first bus configured to receive the first power from the power source. The architecture also has a converter configured to receive the first power from the first bus and convert the first power to a second power, wherein a voltage of the second power is greater than a voltage of the first power, and a second bus configured to receive the second power from the converter. The architecture further has a power storage device configured to receive the second power from the second bus and deliver the second power to the second bus, a propulsion motor configured to receive the second power from the second bus, and an accessory motor configured to receive the second power from the second bus.

  20. Essays on the Digital Divide

    Science.gov (United States)

    Abdelfattah, Belal M. T.

    2013-01-01

    The digital divide is a phenomenon that is globally persistent, despite rapidly decreasing costs in technology. While much of the variance in the adoption and use of information communication technology (ICT) that defines the digital divide can be explained by socioeconomic and demographic variables, there is still significant unaccounted variance…

  1. Frequency to Voltage Converter Analog Front-End Prototype

    Science.gov (United States)

    Mata, Carlos; Raines, Matthew

    2012-01-01

    The frequency to voltage converter analog front end evaluation prototype (F2V AFE) is an evaluation board designed for comparison of different methods of accurately extracting the frequency of a sinusoidal input signal. A configurable input stage is routed to one or several of five separate, configurable filtering circuits, and then to a configurable output stage. Amplifier selection and gain, filter corner frequencies, and comparator hysteresis and voltage reference are all easily configurable through the use of jumpers and potentiometers.

  2. Resistor dividers and ac grids; Spannungsteiler und Gleichstromnetzwerke

    Energy Technology Data Exchange (ETDEWEB)

    Biechl, H. [Hochschule Kempten (Germany). Werner-von-Siemens-Labor fuer Elektrische Antriebe und Mechatronik

    2010-01-15

    The contribution discusses the subject of resistor dividers and shows how to calculate the mathematical voltage division rules. It also explains how a d.c. grid can be calculated with the aid of Ohm's law and the two laws of Kirchhoff. (orig.)

  3. Experimental validation of prototype high voltage bushing

    Science.gov (United States)

    Shah, Sejal; Tyagi, H.; Sharma, D.; Parmar, D.; M. N., Vishnudev; Joshi, K.; Patel, K.; Yadav, A.; Patel, R.; Bandyopadhyay, M.; Rotti, C.; Chakraborty, A.

    2017-08-01

    Prototype High voltage bushing (PHVB) is a scaled down configuration of DNB High Voltage Bushing (HVB) of ITER. It is designed for operation at 50 kV DC to ensure operational performance and thereby confirming the design configuration of DNB HVB. Two concentric insulators viz. Ceramic and Fiber reinforced polymer (FRP) rings are used as double layered vacuum boundary for 50 kV isolation between grounded and high voltage flanges. Stress shields are designed for smooth electric field distribution. During ceramic to Kovar brazing, spilling cannot be controlled which may lead to high localized electrostatic stress. To understand spilling phenomenon and precise stress calculation, quantitative analysis was performed using Scanning Electron Microscopy (SEM) of brazed sample and similar configuration modeled while performing the Finite Element (FE) analysis. FE analysis of PHVB is performed to find out electrical stresses on different areas of PHVB and are maintained similar to DNB HV Bushing. With this configuration, the experiment is performed considering ITER like vacuum and electrical parameters. Initial HV test is performed by temporary vacuum sealing arrangements using gaskets/O-rings at both ends in order to achieve desired vacuum and keep the system maintainable. During validation test, 50 kV voltage withstand is performed for one hour. Voltage withstand test for 60 kV DC (20% higher rated voltage) have also been performed without any breakdown. Successful operation of PHVB confirms the design of DNB HV Bushing. In this paper, configuration of PHVB with experimental validation data is presented.

  4. Automated Voltage Control in LHCb

    CERN Document Server

    Granado Cardoso, L; Jacobsson, R

    2011-01-01

    LHCb is one of the 4 LHC experiments. In order to ensure the safety of the detector and to maximize efficiency, LHCb needs to coordinate its own operations, in particular the voltage configuration of the different subdetectors, according to the accelerator status. A control software has been developed for this purpose, based on the Finite State Machine toolkit and the SCADA system used for control throughout LHCb (and the other LHC experiments). This software permits to efficiently drive both the Low Voltage (LV) and High Voltage (HV) systems of the 10 different sub-detectors that constitute LHCb, setting each sub-system to the required voltage (easily configurable at run-time) based on the accelerator state. The control software is also responsible for monitoring the state of the Sub-detector voltages and adding it to the event data in the form of status-bits. Safe and yet flexible operation of the LHCb detector has been obtained and automatic actions, triggered by the state changes of the ...

  5. Divided by the Market, Divided by the State

    DEFF Research Database (Denmark)

    Wulfgramm, Melike; Starke, Peter

    2016-01-01

    of the individual differences, the analysis also shows, for the first time, that both high inequality and strongly redistributive policies divide public opinion along the lines of socioeconomic position. Put differently, while market inequality may be associated with less cohesive attitudes, a highly redistributive...

  6. Getting Past the "Digital Divide"

    Science.gov (United States)

    McCollum, Sean

    2011-01-01

    In the last decade, "digital divide" has become a catchphrase for the stubborn disparity in IT resources between communities, especially in regard to education. Low-income, rural and minority populations have received special scrutiny as the technological "have-nots." This article presents success stories of educators who can work around obstacles…

  7. Dividing Fractions: A Pedagogical Technique

    Science.gov (United States)

    Lewis, Robert

    2016-01-01

    When dividing one fraction by a second fraction, invert, that is, flip the second fraction, then multiply it by the first fraction. To multiply fractions, simply multiply across the denominators, and multiply across the numerators to get the resultant fraction. So by inverting the division of fractions it is turned into an easy multiplication of…

  8. Accurate Switched-Voltage voltage averaging circuit

    OpenAIRE

    金光, 一幸; 松本, 寛樹

    2006-01-01

    Abstract ###This paper proposes an accurate Switched-Voltage (SV) voltage averaging circuit. It is presented ###to compensated for NMOS missmatch error at MOS differential type voltage averaging circuit. ###The proposed circuit consists of a voltage averaging and a SV sample/hold (S/H) circuit. It can ###operate using nonoverlapping three phase clocks. Performance of this circuit is verified by PSpice ###simulations.

  9. Comparison of Algorithms for Control of Loads for Voltage Regulation

    DEFF Research Database (Denmark)

    Douglass, Philip James; Han, Xue; You, Shi

    2014-01-01

    Autonomous flexible loads can be utilized to regulate voltag e on low voltage feeders. This paper compares two algorithms for controllin g loads: a simple voltage droop, where load power consumption is a varied in proportio n to RMS voltage; and a normalized relative voltage droop, which modifies...... the simpl e voltage droop by subtracting the mean voltage value at the bus and dividing by the standard deviation. These two controllers are applied to hot water heaters simul ated in a simple residential feeder. The simulation results show that both controllers r educe the frequency of undervoltage events...

  10. Information Societies and Digital Divides

    CERN Document Server

    Sorj, Bernardo

    2008-01-01

    The book argues ICT are part of the set of goods and services that determine quality of life, social inequality and the chances for economic development. Therefore understanding the digital divide demands a broader discussion of the place of ICT within each society and in the international system. The author argues against the perspectives that either isolates ICT from other basic social goods (in particular education and employment) as well as those that argue that new technologies are luxury of a consumer society. Though the author accepts that new technologies are not a panacea for the problems of inequality, access to them become a condition of full integration of social life. Using examples mainly from Latin America, the work presents some general policy proposals on the fight against the digital divide which take in consideration other dimensions of social inequality and access to public goods. Bernardo Sorj was born in Montevideo, Uruguay. He is a naturalized Brazilian, living in Brazil since 1976. He ...

  11. New Voltage Mode Universal Filters Using Only Two CDBAs

    OpenAIRE

    J. K. Pathak; Singh, A. K.; Raj Senani

    2013-01-01

    Two new configurations for voltage mode universal filters (VMUFs) using only two current differencing buffered amplifiers (CDBAs) are proposed. Both of the new configurations can realize all the five standard types of the filters, namely, low pass (LP), high pass (HP), band pass (BP), band stop (BS), and all pass (AP), from the same topology. In contrast to previously known CDBA-based VMUFs, the new configurations do not need an additional active device for voltage inversion to realize all pa...

  12. Cavity Voltage Phase Modulation MD

    CERN Document Server

    Mastoridis, Themistoklis; Molendijk, John; Timko, Helga; CERN. Geneva. ATS Department

    2016-01-01

    The LHC RF/LLRF system is currently configured for extremely stable RF voltage to minimize transient beam loading effects. The present scheme cannot be extended beyond nominal beam current since the demanded power would exceed the peak klystron power and lead to saturation. A new scheme has therefore been proposed: for beam currents above nominal (and possibly earlier), the cavity phase modulation by the beam will not be corrected (transient beam loading), but the strong RF feedback and One-Turn Delay feedback will still be active for loop and beam stability in physics. To achieve this, the voltage set point will be adapted for each bunch. The goal of this MD was to test a new algorithm that would adjust the voltage set point to achieve the cavity phase modulation that would minimize klystron forward power.

  13. Pulse swallowing frequency divider with low power and compact structure

    Institute of Scientific and Technical Information of China (English)

    Gao Haijun; Sun Lingling; Cai Chaobo; Zhan Haiting

    2012-01-01

    A pulse swallowing frequency divider with low power and compact structure is presented.One of the DFFs in the divided by 2/3 prescaler is controlled by the modulus control signal,and automatically powered off when it has no contribution to the operation of the prescaler.The DFFs in the program counter and the swallow counter are shared to compose a compact structure,which reduces the power consumption further.The proposed multi-modulus frequency divider was implemented in a standard 65 nm CMOS process with an area of 28 ×22 μm2.The power consumption of the divider is 0.6 mW under 1.2 V supply voltage when operating at 988 MHz.

  14. Transformer-based design techniques for oscillators and frequency dividers

    CERN Document Server

    Luong, Howard Cam

    2016-01-01

    This book provides in-depth coverage of transformer-based design techniques that enable CMOS oscillators and frequency dividers to achieve state-of-the-art performance.  Design, optimization, and measured performance of oscillators and frequency dividers for different applications are discussed in detail, focusing on not only ultra-low supply voltage but also ultra-wide frequency tuning range and locking range.  This book will be an invaluable reference for anyone working or interested in CMOS radio-frequency or mm-Wave integrated circuits and systems.

  15. Resistor dividers on the march; Vorwaerts mit ohmschen Spannungsteilern

    Energy Technology Data Exchange (ETDEWEB)

    Wollschlaeger, P. [Siemens AG, Erlangen (Germany). Bereich Energieuebertragung und -verteilung

    2000-02-07

    Rising costs and the growing scope of functions demanded nowadays of a medium-voltage switchpanel are forcing manufactures to turn to innovative, intelligent solutions. Frequently, customer specifications cannot be costeffectively met with conventional technology; new ground has to be broken. A typical example is the superseding of conventional voltage transformers (with separate cores for protection and measurement) by a voltage sensor with interface to an instrument amplifier. The advantages are clear: Voltage sensors that no longer need to be configured according to network data and purpose of use. It is time for sensorics to find their way into medium voltage equipment; in industrial processes sensors are already long established. (orig.) [German] Steigender Kostendruck bei gleichzeitig zunehmender Funktionalitaet, die heute von einem Mittelspannungsschaltfeld gefordert wird, zwingt den Hersteller zu neuen, intelligenten Loesungen. Zunehmend sind die Kundenwuensche mit konventioneller Technik nicht mehr kostenguenstig zu realisieren, sondern erfordern es, neue Wege zu beschreiten. Ein Beispiel dafuer ist der Ersatz konventioneller Spannungswandler mit getrennten Kernen fuer Schutz und Messung durch einen Spannungssensor mit Schnittstelle zu einem Messverstaerker. Der Vorteil sind Spannungssensoren, die nicht mehr individuell nach Netzdaten und Verwendungszweck projektiert werden muessen. Es wird Zeit, dass die Sensortechnik auch in der Mittelspannung einzieht - in industriellen Prozessen sind Sensoren schon lange im Einsatz. (orig.)

  16. Supply chain configuration concepts, solutions, and applications

    CERN Document Server

    Chandra, Charu

    2016-01-01

    This book discusses the models and tools available for solving configuration problems, emphasizes the value of model integration to obtain comprehensive and robust configuration decisions, proposes solutions for supply chain configuration in the presence of stochastic and dynamic factors, and illustrates application of the techniques discussed in applied studies. It is divided into four parts, which are devoted to defining the supply chain configuration problem and identifying key issues, describing solutions to various problems identified, proposing technologies for enabling supply chain confirmations, and discussing applied supply chain configuration problems. Its distinguishing features are: an explicit focus on the configuration problem an in-depth coverage of configuration models an emphasis on model integration and application of information modeling techniques in decision-making New to this edition is Part II: Technologies, which introduces readers to various technologies being utilized for supply chai...

  17. Study on Optimization of Capacity Configuration of Stationary Super Capacitor Storage System for Improving Energy Efficiency and Voltage Profile%基于节能稳压的地面式超级电容储能系统容量配置优化研究

    Institute of Scientific and Technical Information of China (English)

    2016-01-01

    The installation of super capacitor in urban rail transit system allows the recovery of the braking ener-gy,which results in further energy savings,better pantograph voltage profile,as well as effective reduction of the occurrence of the regenerative braking failure of the train.In this paper,firstly,the energy efficiency and regeneration failure evaluation function was put forward based on the characteristics of the urban rail trac-tion power supply network.Then,a simulation platform for the energy storage system of the stationary super capacitor applicable to urban rail transit was established.A case study was conducted on a metro line to analyze the impact of the positioning of super capacitor and storage energy selection on the energy saving efficiency and voltage stabilizing effect of the urban rail transit under different departure headways.According to the simula-tion results,compared to the scheme of installing a super capacitor at every substation,the scheme of setting one lager capacity super capacitor for several substations could be a better capacity configuration scheme, which provides reference for the optimization design of capacity configuration of super capacitor storage system.%在城市轨道交通中应用超级电容可以实现城轨交通的进一步节能,并有效降低列车发生再生失效的概率.本文结合城轨牵引供电网特点提出供电网的节能稳压评估函数,建立适用于城轨交通的地面式超级电容储能系统仿真平台.以某地铁线路为例,分析在不同发车间隔下,超级电容的设置位置及储能量选取对城轨交通节能效率及稳压效果的影响.仿真结果表明,相比于全线每座牵引变电所均设置超级电容,隔多站设置大容量超级电容是更合理的容量配置方案,为超级电容容量配置方案的优化设计提供了参考依据.

  18. Determination of the aging offset voltage of AMR sensors based on accelerated degradation test

    NARCIS (Netherlands)

    Zambrano, Andreina; Kerkhoff, Hans G.

    2015-01-01

    Usually Anisotropic Magnetoresistance angle sensors are configured with two Wheatstone bridges, but an undesirable offset voltage included in the sensor output affects its accuracy. The total offset voltage combines a voltage due to resistance mismatches during manufacturing and a voltage from inequ

  19. Radiatively heated high voltage pyroelectric crystal pulser

    Energy Technology Data Exchange (ETDEWEB)

    Antolak, A.J., E-mail: antolak@sandia.gov [Sandia National Laboratories, Livermore, CA 94550 (United States); Chen, A.X. [Sandia National Laboratories, Livermore, CA 94550 (United States); Leung, K.-N. [Sandia National Laboratories, Livermore, CA 94550 (United States); Nuclear Engineering Department, University of California, Berkeley (United States); Morse, D.H.; Raber, T.N. [Sandia National Laboratories, Livermore, CA 94550 (United States)

    2014-01-21

    Thin lithium tantalate pyroelectric crystals in a multi-stage pulser were heated by quartz lamps during their charging phase to generate high voltage pulses. The charging voltage was determined empirically based on the measured breakdown voltage in air and verified by the induced breakdown voltage of an external high voltage power supply. A four-stage pyroelectric crystal device generated pulse discharges of up to 86 kV using both quartz lamps (radiative) and thermoelectric (conductive) heating. Approximately 50 mJ of electrical energy was harvested from the crystals when radiatively heated in air, and up to 720 mJ was produced when the crystals were submerged in a dielectric fluid. It is anticipated that joule-level pulse discharges could be obtained by employing additional stages and optimizing the heating configuration.

  20. A low voltage CMOS low drop-out voltage regulator

    Science.gov (United States)

    Bakr, Salma Ali; Abbasi, Tanvir Ahmad; Abbasi, Mohammas Suhaib; Aldessouky, Mohamed Samir; Abbasi, Mohammad Usaid

    2009-05-01

    A low voltage implementation of a CMOS Low Drop-Out voltage regulator (LDO) is presented. The requirement of low voltage devices is crucial for portable devices that require extensive computations in a low power environment. The LDO is implemented in 90nm generic CMOS technology. It generates a fixed 0.8V from a 2.5V supply which on discharging goes to 1V. The buffer stage used is unity gain configured unbuffered OpAmp with rail-to-rail swing input stage. The simulation result shows that the implemented circuit provides load regulation of 0.004%/mA and line regulation of -11.09mV/V. The LDO provides full load transient response with a settling time of 5.2μs. Further, the dropout voltage is 200mV and the quiescent current through the pass transistor (Iload=0) is 20μA. The total power consumption of this LDO (excluding bandgap reference) is only 80μW.

  1. Crossroads - Bridging the Digital Divide

    Directory of Open Access Journals (Sweden)

    David Cobb

    2005-03-01

    Full Text Available It’s so good to be in Cambridge, it feels almost like home. Let me start by stating that in the past year ITMB, a successful map publisher in British Columbia, Canada published more paper map titles than at any time in their history. Similarly, the U.S. Geological Survey (USGS recently announced that they have ceased producing paper from their aerial photography archive and will only produce digital copies. I believe that both of these facts speak to the future of maps and digital data. It means there will be paper maps well into the future and there will be an increasing array of digital data - some of it reformatted, as in the USGS case, and most of it will be born digital. When asked to speak about GIS and its role in libraries I often find myself in a conundrum - am I here to slay the dragon, or to pet the dragon. The role of technology in libraries is not one that has been embraced by everyone, and often the technology itself seems to have been force-fed upon us. The library profession is not one that has historically been a proponent of change and the very nature of GIS is change. In one sense, we have been given the choice of becoming paper museums or, at the very least, making GIS technology available in our collections. Today, I would like to review the many ways that GIS is, or will, affect our collections. I will divide the presentation into a general overview of GIS in libraries, how it affects our acquisitions or collection development policies, its effect on cataloging, on reference services, staffing, and our web services. Then I will shift the focus a little and discuss the current situation at the Harvard Map Collection, the future role of legacy collections, and a look to the future.

  2. A Novel Chopper Circuit Having Divided Multi-load

    Science.gov (United States)

    Yamamoto, Isamu; Matsui, Keiju; Mori, Hideki; Yao, Yugo

    A dc-dc converter is being widely used for various household appliances and for industry applications. The dc-dc converter is powered from single battery, and the voltage is varied according to the purpose. In the vehicle, various accessories whose electric power is different are being used. Thus, plural number of dc-dc converter should be provided, so these situations bring complicated circuits, and accordingly, higher cost. Moreover, this is not limited to the vehicle applications. For instance, for analog circuits and digital circuits, various power supplies with different voltages are used sometimes. Under such backgrounds, in this paper, we propose a novel dc-dc converter with simply circuit configuration which can supply to two or more different output loads. This converter can control output voltages by controlling duty ratio by using typically two switching devices, which is composed by single boost-switch and single buck-switch. The output voltage can be controlled widely. A few modified circuits developed from the fundamental circuit are represented including the general multi-load circuit. Theoretical equations are solved, where results are confirmed by simulations and experiments.

  3. Conceptualizing Embedded Configuration

    DEFF Research Database (Denmark)

    Oddsson, Gudmundur Valur; Hvam, Lars; Lysgaard, Ole

    2006-01-01

    and services. The general idea can be named embedded configuration. In this article we intend to conceptualize embedded configuration, what it is and is not. The difference between embedded configuration, sales configuration and embedded software is explained. We will look at what is needed to make embedded...... configuration systems. That will include requirements to product modelling techniques. An example with consumer electronics will illuminate the elements of embedded configuration in settings that most can relate to. The question of where embedded configuration would be relevant is discussed, and the current...

  4. Programmable high voltage power supply with regulation confined to the high voltage section

    Science.gov (United States)

    Castell, Karen D. (Inventor); Ruitberg, Arthur P. (Inventor)

    1994-01-01

    A high voltage power supply in a dc-dc converter configuration includes a pre-regulator which filters and regulates the dc input and drives an oscillator which applies, in turn, a low voltage ac signal to the low side of a step-up high voltage transformer. The high voltage side of the transformer drives a voltage multiplier which provides a stepped up dc voltage to an output filter. The output voltage is sensed by a feedback network which then controls a regulator. Both the input and output of the regulator are on the high voltage side, avoiding isolation problems. The regulator furnishes a portion of the drive to the voltage multiplier, avoiding having a regulator in series with the load with its attendant, relatively high power losses. This power supply is highly regulated, has low power consumption, a low parts count and may be manufactured at low cost. The power supply has a programmability feature that allows for the selection of a large range of output voltages.

  5. Transient Voltage Recorder

    Science.gov (United States)

    Medelius, Pedro J. (Inventor); Simpson, Howard J. (Inventor)

    2002-01-01

    A voltage transient recorder can detect lightning induced transient voltages. The recorder detects a lightning induced transient voltage and adjusts input amplifiers to accurately record transient voltage magnitudes. The recorder stores voltage data from numerous monitored channels, or devices. The data is time stamped and can be output in real time, or stored for later retrieval. The transient recorder, in one embodiment, includes an analog-to-digital converter and a voltage threshold detector. When an input voltage exceeds a pre-determined voltage threshold, the recorder stores the incoming voltage magnitude and time of arrival. The recorder also determines if its input amplifier circuits clip the incoming signal or if the incoming signal is too low. If the input data is clipped or too low, the recorder adjusts the gain of the amplifier circuits to accurately acquire subsequent components of the lightning induced transients.

  6. Some results on numerical divided difference formulas

    Institute of Scientific and Technical Information of China (English)

    Wang; Xinghua; Wang; Heyu; Ming-Jun; Lai

    2005-01-01

    The remainder estimates of numerical divided difference formula are given for the functions of lower and higher smoothness, respectively. Then several divided difference formulas with super-convergence are derived with their remainder expressions.

  7. Offset Correction Techniques for Voltage Sense Amplifiers

    NARCIS (Netherlands)

    Groeneveld, S.

    2006-01-01

    This report deals with offset correction techniques for voltage sense amplifiers and is divided into two different parts: 1) mismatch and 2) offset correction techniques. First a literature study is done on the subject mismatch with specially focus on the future. Mismatch of a transistor is determin

  8. Automatic voltage imbalance detector

    Science.gov (United States)

    Bobbett, Ronald E.; McCormick, J. Byron; Kerwin, William J.

    1984-01-01

    A device for indicating and preventing damage to voltage cells such as galvanic cells and fuel cells connected in series by detecting sequential voltages and comparing these voltages to adjacent voltage cells. The device is implemented by using operational amplifiers and switching circuitry is provided by transistors. The device can be utilized in battery powered electric vehicles to prevent galvanic cell damage and also in series connected fuel cells to prevent fuel cell damage.

  9. Tech, Teachers & Teens: Bridging the Divide

    Science.gov (United States)

    Stuht, Amy Colcord; Colcord, Cean

    2011-01-01

    In past decades, the "digital divide" referred to the gap between those who could afford access to technology and those who could not. The divide has shifted in recent years to reflect the growing technological chasm between teachers and their students: today's schools and teenagers' worlds. The digital divide is widening and deepening…

  10. The Myth about the Digital Divide

    Science.gov (United States)

    Hawkins, Brian L.; Oblinge, Diana G.

    2006-01-01

    Although computer ownership is not 100 percent, progress has been made on closing the digital divide. However, defining the digital divide according to the haves and have-nots of computer ownership is only a starting point. Beyond computer ownership, colleges and universities should explore the "second-level digital divide," which can be…

  11. Diversity, Disability, and Geographic Digital Divide

    Science.gov (United States)

    Sumari, Melati; Carr, Erika; Ndebe-Ngovo, Manjerngie

    2006-01-01

    The phenomenon called digital divide was the focus of this paper. Diversity, disability, and geographical digital divide were relevant to this collaborative project. An extensive review of the literature was conducted for the completion of this project. The evidence for the digital divide in terms of race, level of education, and gender in the…

  12. Mixed voltage VLSI design

    Science.gov (United States)

    Panwar, Ramesh; Rennels, David; Alkalaj, Leon

    1993-01-01

    A technique for minimizing the power dissipated in a Very Large Scale Integration (VLSI) chip by lowering the operating voltage without any significant penalty in the chip throughput even though low voltage operation results in slower circuits. Since the overall throughput of a VLSI chip depends on the speed of the critical path(s) in the chip, it may be possible to sustain the throughput rates attained at higher voltages by operating the circuits in the critical path(s) with a high voltage while operating the other circuits with a lower voltage to minimize the power dissipation. The interface between the gates which operate at different voltages is crucial for low power dissipation since the interface may possibly have high static current dissipation thus negating the gains of the low voltage operation. The design of a voltage level translator which does the interface between the low voltage and high voltage circuits without any significant static dissipation is presented. Then, the results of the mixed voltage design using a greedy algorithm on three chips for various operating voltages are presented.

  13. Plural voltage minima in an arc-heated channel flow

    Science.gov (United States)

    Sasoh, A.

    2001-04-01

    In flows through a channel with varying cross-sectional area, the impulse and total enthalpy can be increased by superimposing an electrical discharge. The flow field is determined from the inlet flow condition, channel geometry, and discharge specifications. In this study, steady-state, quasi-one-dimensional flows interacting with an arc discharge are computed numerically. Once the arc column configuration is given, the discharge voltage is computed from the solution of flow field variables. For a constant discharge current, there exist plural column configurations which yield a minimum discharge voltage. This result explains the fluid-dynamic mechanisms of the existence of plural voltage modes in an arcjet operation.

  14. Low voltage electron beam accelerators

    Energy Technology Data Exchange (ETDEWEB)

    Ochi, Masafumi [Iwasaki Electric Co., Ltd., Tokyo (Japan)

    2003-02-01

    Widely used electron accelerators in industries are the electron beams with acceleration voltage at 300 kV or less. The typical examples are shown on manufactures in Japan, equipment configuration, operation, determination of process parameters, and basic maintenance requirement of the electron beam processors. New electron beam processors with acceleration voltage around 100 kV were introduced maintaining the relatively high dose speed capability of around 10,000 kGy x mpm at production by ESI (Energy Science Inc. USA, Iwasaki Electric Group). The application field like printing and coating for packaging requires treating thickness of 30 micron or less. It does not require high voltage over 110 kV. Also recently developed is a miniature bulb type electron beam tube with energy less than 60 kV. The new application area for this new electron beam tube is being searched. The drive force of this technology to spread in the industries would be further development of new application, process and market as well as the price reduction of the equipment, upon which further acknowledgement and acceptance of the technology to societies and industries would entirely depend. (Y. Tanaka)

  15. Combined Digital Electronic Current and Voltage Transducer

    Institute of Scientific and Technical Information of China (English)

    段雄英; 邹积岩; 等

    2002-01-01

    A high-performance current and voltage measurement system has been developed in power system.The system is composed of two parts:one current measurement element and one voltage measurement element.A Rogowski coil and a capacitive voltage divider are used respectively for the line current and voltage measurements.Active electronic components are used to modulate signal,and power supply for these components is drawn from power line via an auxiliary current transformer,Measurement signal is transmitted y optical fibers,which is resistant to electromagnetic induction and noise,With careful design and the use of digital signal processing technology,the whole system can meet 0.5% accuracy for metering and provides large dynamic range coupled with good accuracy for protective relaying use.

  16. HLT configuration management system

    CERN Document Server

    Daponte, Vincenzo

    2015-01-01

    The CMS High Level Trigger (HLT) is implemented running a streamlined version of the CMS offline reconstruction software running on thousands of CPUs. The CMS software is written mostly in C++, using Python as its configuration language through an embedded CPython interpreter. The configuration of each process is made up of hundreds of modules, organized in sequences and paths. As an example, the HLT configurations used for 2011 data taking comprised over 2200 different modules, organized in more than 400 independent trigger paths. The complexity of the HLT configurations and the large number of configuration produced require the design of a suitable data management system. The present work describes the designed solution to manage the considerable number of configurations developed and to assist the editing of new configurations. The system is required to be remotely accessible and OS-independent as well as easly maintainable easy to use. To meet these requirements a three-layers architecture has been choose...

  17. An Optoelectronic High-voltage Probe for Measuring Impulse Voltage Distribution of HVDC Converter Valve

    Institute of Scientific and Technical Information of China (English)

    方志; 邱毓昌

    2007-01-01

    A high-voltage optoelectronic probe is developed for measuring impulse voltage distribution along thyristor units in the HVDC converter valve. The dimension of the resistive voltage divider is optimized by means of numerical compttation of electric field. A pulse frequency modulation (PFM) mode is adopted for the data transmission link because of its immunity to high-intensity electromagnetic interference. Experimental results indicate that the linearity deviation for the whole measuring system is within ± 0.15 %, and therefore it can meet requirements specified by IEC60700-1.

  18. High voltage testing for the MAJORANA DEMONSTRATOR

    Energy Technology Data Exchange (ETDEWEB)

    Abgrall, N. [Nuclear Science Division, Lawrence Berkeley National Laboratory, Berkeley, CA (United States); Arnquist, I.J. [Pacific Northwest National Laboratory, Richland, WA (United States); Avignone, F.T. [Department of Physics and Astronomy, University of South Carolina, Columbia, SC (United States); Oak Ridge National Laboratory, Oak Ridge, TN (United States); Barabash, A.S. [National Research Center “Kurchatov Institute” Institute for Theoretical and Experimental Physics, Moscow (Russian Federation); Bertrand, F.E. [Oak Ridge National Laboratory, Oak Ridge, TN (United States); Bradley, A.W. [Nuclear Science Division, Lawrence Berkeley National Laboratory, Berkeley, CA (United States); Brudanin, V. [Joint Institute for Nuclear Research, Dubna (Russian Federation); Busch, M. [Department of Physics, Duke University, Durham, NC (United States); Triangle Universities Nuclear Laboratory, Durham, NC (United States); Buuck, M. [Center for Experimental Nuclear Physics and Astrophysics, and Department of Physics, University of Washington, Seattle, WA (United States); Byram, D. [Department of Physics, University of South Dakota, Vermillion, SD (United States); Caldwell, A.S. [South Dakota School of Mines and Technology, Rapid City, SD (United States); Chan, Y-D. [Nuclear Science Division, Lawrence Berkeley National Laboratory, Berkeley, CA (United States); Christofferson, C.D. [South Dakota School of Mines and Technology, Rapid City, SD (United States); Chu, P.-H. [Los Alamos National Laboratory, Los Alamos, NM (United States); Cuesta, C., E-mail: ccuesta@uw.edu [Center for Experimental Nuclear Physics and Astrophysics, and Department of Physics, University of Washington, Seattle, WA (United States); Detwiler, J.A.; Doe, P.J. [Center for Experimental Nuclear Physics and Astrophysics, and Department of Physics, University of Washington, Seattle, WA (United States); and others

    2016-07-01

    The MAJORANA Collaboration is constructing the MAJORANA DEMONSTRATOR, an ultra-low background, 44-kg modular high-purity Ge (HPGe) detector array to search for neutrinoless double-beta decay in {sup 76}Ge. The phenomenon of surface micro-discharge induced by high-voltage has been studied in the context of the MAJORANA DEMONSTRATOR. This effect can damage the front-end electronics or mimic detector signals. To ensure the correct performance, every high-voltage cable and feedthrough must be capable of supplying HPGe detector operating voltages as high as 5 kV without exhibiting discharge. R&D measurements were carried out to understand the testing system and determine the optimum design configuration of the high-voltage path, including different improvements of the cable layout and feedthrough flange model selection. Every cable and feedthrough to be used at the MAJORANA DEMONSTRATOR was characterized and the micro-discharge effects during the MAJORANA DEMONSTRATOR commissioning phase were studied. A stable configuration has been achieved, and the cables and connectors can supply HPGe detector operating voltages without exhibiting discharge.

  19. High voltage testing for the MAJORANA DEMONSTRATOR

    Science.gov (United States)

    Abgrall, N.; Arnquist, I. J.; Avignone, F. T.; Barabash, A. S.; Bertrand, F. E.; Bradley, A. W.; Brudanin, V.; Busch, M.; Buuck, M.; Byram, D.; Caldwell, A. S.; Chan, Y.-D.; Christofferson, C. D.; Chu, P.-H.; Cuesta, C.; Detwiler, J. A.; Doe, P. J.; Dunagan, C.; Efremenko, Yu.; Ejiri, H.; Elliott, S. R.; Fu, Z.; Galindo-Uribarri, A.; Giovanetti, G. K.; Goett, J.; Green, M. P.; Gruszko, J.; Guinn, I. S.; Guiseppe, V. E.; Henning, R.; Hoppe, E. W.; Howard, S.; Howe, M. A.; Jasinski, B. R.; Keeter, K. J.; Kidd, M. F.; Konovalov, S. I.; Kouzes, R. T.; LaFerriere, B. D.; Leon, J.; Li, A.; MacMullin, J.; Martin, R. D.; Massarczyk, R.; Meijer, S. J.; Mertens, S.; Orrell, J. L.; O'Shaughnessy, C.; Poon, A. W. P.; Radford, D. C.; Rager, J.; Rielage, K.; Robertson, R. G. H.; Romero-Romero, E.; Shanks, B.; Shirchenko, M.; Snyder, N.; Suriano, A. M.; Tedeschi, D.; Thompson, A.; Ton, K. T.; Trimble, J. E.; Varner, R. L.; Vasilyev, S.; Vetter, K.; Vorren, K.; White, B. R.; Wilkerson, J. F.; Wiseman, C.; Xu, W.; Yakushev, E.; Yu, C.-H.; Yumatov, V.

    2016-07-01

    The MAJORANA Collaboration is constructing the MAJORANA DEMONSTRATOR, an ultra-low background, 44-kg modular high-purity Ge (HPGe) detector array to search for neutrinoless double-beta decay in 76Ge. The phenomenon of surface micro-discharge induced by high-voltage has been studied in the context of the MAJORANA DEMONSTRATOR. This effect can damage the front-end electronics or mimic detector signals. To ensure the correct performance, every high-voltage cable and feedthrough must be capable of supplying HPGe detector operating voltages as high as 5 kV without exhibiting discharge. R&D measurements were carried out to understand the testing system and determine the optimum design configuration of the high-voltage path, including different improvements of the cable layout and feedthrough flange model selection. Every cable and feedthrough to be used at the MAJORANA DEMONSTRATOR was characterized and the micro-discharge effects during the MAJORANA DEMONSTRATOR commissioning phase were studied. A stable configuration has been achieved, and the cables and connectors can supply HPGe detector operating voltages without exhibiting discharge.

  20. High voltage testing for the Majorana Demonstrator

    Energy Technology Data Exchange (ETDEWEB)

    Abgrall, N.; Arnquist, Isaac J.; Avignone, F. T.; Barabash, A.; Bertrand, F.; Bradley, A. W.; Brudanin, V.; Busch, Matthew; Buuck, M.; Byram, D.; Caldwell, A. S.; Chan, Yuen-Dat; Christofferson, C. D.; Chu, Pamela M.; Cuesta, C.; Detwiler, Jason A.; Doe, P. J.; Dunagan, C.; Efremenko, Yuri; Ejiri, H.; Elliott, S. R.; Fu, Z.; Galindo-Uribarri, A.; Giovanetti, G. K.; Goett, J.; Green, M. P.; Gruszko, J.; Guinn, I.; Guiseppe, V. E.; Henning, R.; Hoppe, Eric W.; Howard, S.; Howe, M. A.; Jasinski, B. R.; Keeter, K.; Kidd, M. F.; Konovalov, S.; Kouzes, Richard T.; Laferriere, Brian D.; Leon, Jonathan D.; Li, Alexander D.; MacMullin, J.; Martin, R. D.; Massarcyk, R.; Meijer, S. J.; Mertens, S.; Orrell, John L.; O' Shaughnessy, C.; Poon, Alan W.; Radford, D. C.; Rager, J.; Rielage, Keith; Robertson, R. G. H.; Romero Romo, M.; Shanks, B.; Shirchenko, M.; Snyder, N.; Suriano, Anne-Marie E.; Tedeschi, D.; Thompson, Andrew; Ton, K. T.; Trimble, J. E.; Varner, R. L.; Vasilyev, Sergey; Vetter, Kai; Vorren, Kris R.; White, Brandon R.; Wilkerson, J. F.; Wiseman, C.; Xu, W.; Yakushev, E.; Yu, Chang-Hong; Yumatov, V.

    2016-07-01

    The Majorana Collaboration is constructing theMajorana Demonstrator, an ultra-low background, 44-kg modular high-purity Ge (HPGe) detector array to search for neutrinoless double-beta decay in 76Ge. The phenomenon of surface micro-discharge induced by high-voltage has been studied in the context of theMajorana Demonstrator. This effect can damage the front-end electronics or mimic detector signals. To ensure the correct performance, every high-voltage cable and feedthrough must be capable of supplying HPGe detector operating voltages as high as 5 kV without exhibiting discharge. R&D measurements were carried out to understand the testing system and determine the optimum design configuration of the high-voltage path, including different improvements of the cable layout and feedthrough flange model selection. Every cable and feedthrough to be used at the Majorana Demonstrator was characterized and the micro-discharge effects during theMajorana Demonstrator commissioning phase were studied. A stable configuration has been achieved, and the cables and connectors can supply HPGe detector operating voltages without exhibiting discharge.

  1. Fast frequency divider circuit using combinational logic

    Science.gov (United States)

    Helinski, Ryan

    2017-05-30

    The various technologies presented herein relate to performing on-chip frequency division of an operating frequency of a ring oscillator (RO). Per the various embodiments herein, a conflict between RO size versus operational frequency can be addressed by dividing the output frequency of the RO to a frequency that can be measured on-chip. A frequency divider circuit (comprising NOR gates and latches, for example) can be utilized in conjunction with the RO on the chip. In an embodiment, the frequency divider circuit can include a pair of latches coupled to the RO to facilitate dividing the oscillating frequency of the RO by 2. In another embodiment, the frequency divider circuit can include four latches (operating in pairs) coupled to the RO to facilitate dividing the oscillating frequency of the RO by 4. A plurality of ROs can be MUXed to the plurality of ROs by a single oscillation-counting circuit.

  2. Affinity and Hostility in Divided Communities: a Mathematical Model

    CERN Document Server

    Thron, Christopher

    2015-01-01

    We propose, develop, and analyze a mathematical model of intergroup attitudes in a community that is divided between two distinct social groups (which may be distinguished by religion, ethnicity, or some other socially distinguishing factor). The model is based on very simple premises that are both intuitive and justified by sociological research. We investigate the behavior of the model in various special cases, for various model configurations. We discuss the stability of the model, and the continuous or discontinuous dependence of model behavior on various parameters. Finally, we discuss possible implications for strategies to improve intergroup affinity, and to defuse tension and prevent deterioration of intergroup relationships.

  3. Business Model Process Configurations

    DEFF Research Database (Denmark)

    Taran, Yariv; Nielsen, Christian; Thomsen, Peter

    2015-01-01

    Purpose – The paper aims: 1) To develop systematically a structural list of various business model process configuration and to group (deductively) these selected configurations in a structured typological categorization list. 2) To facilitate companies in the process of BM innovation......, by developing (inductively) an ontological classification framework, in view of the BM process configurations typology developed. Design/methodology/approach – Given the inconsistencies found in the business model studies (e.g. definitions, configurations, classifications) we adopted the analytical induction...... method of data analysis. Findings - A comprehensive literature review and analysis resulted in a list of business model process configurations systematically organized under five classification groups, namely, revenue model; value proposition; value configuration; target customers, and strategic...

  4. A Design of High—precision High—Voltage Fiber—Optic Analog Signal Isolation Converter

    Institute of Scientific and Technical Information of China (English)

    李建伟; 许留伟; 等

    2002-01-01

    This paper introduces a design of high-precision high-voltage fiber-optic analog signal isolation converter based on the technology of Voltage-to-Frequency(V/F) and Frequency-to-Voltage(F/V) conversion.It describes the principle,system configuration and hardware desin.

  5. A design of High-precision High-Voltage Fiber-Optic Analog Signal Isolation Converter

    Institute of Scientific and Technical Information of China (English)

    李建伟; 许留伟; 刘小宁; 杨雷

    2002-01-01

    This paper introduces a design of high-prectison high-voltage fiber-optic analog sig-nal isoaltion converter based on the technology of Voltage-to-Fequency (V/F)and Frequency -to Voltage(F/V) conversion It describes the principle ,system configuration and hardware design

  6. Technological Aspects: High Voltage

    CERN Document Server

    Faircloth, D C

    2013-01-01

    This paper covers the theory and technological aspects of high-voltage design for ion sources. Electric field strengths are critical to understanding high-voltage breakdown. The equations governing electric fields and the techniques to solve them are discussed. The fundamental physics of high-voltage breakdown and electrical discharges are outlined. Different types of electrical discharges are catalogued and their behaviour in environments ranging from air to vacuum are detailed. The importance of surfaces is discussed. The principles of designing electrodes and insulators are introduced. The use of high-voltage platforms and their relation to system design are discussed. The use of commercially available high-voltage technology such as connectors, feedthroughs and cables are considered. Different power supply technologies and their procurement are briefly outlined. High-voltage safety, electric shocks and system design rules are covered.

  7. Airport Configuration Prediction Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Airport configuration is a primary factor in various airport characteristics such as arrival and departure capacities and terminal area traffic patterns. These...

  8. CONFIGURATION GENERATOR MODEL

    Energy Technology Data Exchange (ETDEWEB)

    A. Alsaed

    2004-11-18

    ''The Disposal Criticality Analysis Methodology Topical Report'' prescribes an approach to the methodology for performing postclosure criticality analyses within the monitored geologic repository at Yucca Mountain, Nevada. An essential component of the methodology is the ''Configuration Generator Model for In-Package Criticality'' that provides a tool to evaluate the probabilities of degraded configurations achieving a critical state. The configuration generator model is a risk-informed, performance-based process for evaluating the criticality potential of degraded configurations in the monitored geologic repository. The method uses event tree methods to define configuration classes derived from criticality scenarios and to identify configuration class characteristics (parameters, ranges, etc.). The probabilities of achieving the various configuration classes are derived in part from probability density functions for degradation parameters. The NRC has issued ''Safety Evaluation Report for Disposal Criticality Analysis Methodology Topical Report, Revision 0''. That report contained 28 open items that required resolution through additional documentation. Of the 28 open items, numbers 5, 6, 9, 10, 18, and 19 were concerned with a previously proposed software approach to the configuration generator methodology and, in particular, the k{sub eff} regression analysis associated with the methodology. However, the use of a k{sub eff} regression analysis is not part of the current configuration generator methodology and, thus, the referenced open items are no longer considered applicable and will not be further addressed.

  9. Ansible configuration management

    CERN Document Server

    Hall, Daniel

    2013-01-01

    Ansible Configuration Management"" is a step-by-step tutorial that teaches the use of Ansible for configuring Linux machines.This book is intended for anyone looking to understand the basics of Ansible. It is expected that you will have some experience of how to set up and configure Linux machines. In parts of the book we cover configuration files of BIND, MySQL, and other Linux daemons, therefore a working knowledge of these would be helpful but are certainly not required.

  10. High voltage engineering

    CERN Document Server

    Rizk, Farouk AM

    2014-01-01

    Inspired by a new revival of worldwide interest in extra-high-voltage (EHV) and ultra-high-voltage (UHV) transmission, High Voltage Engineering merges the latest research with the extensive experience of the best in the field to deliver a comprehensive treatment of electrical insulation systems for the next generation of utility engineers and electric power professionals. The book offers extensive coverage of the physical basis of high-voltage engineering, from insulation stress and strength to lightning attachment and protection and beyond. Presenting information critical to the design, selec

  11. High voltage test techniques

    CERN Document Server

    Kind, Dieter

    2001-01-01

    The second edition of High Voltage Test Techniques has been completely revised. The present revision takes into account the latest international developments in High Voltage and Measurement technology, making it an essential reference for engineers in the testing field.High Voltage Technology belongs to the traditional area of Electrical Engineering. However, this is not to say that the area has stood still. New insulating materials, computing methods and voltage levels repeatedly pose new problems or open up methods of solution; electromagnetic compatibility (EMC) or components and systems al

  12. Mitigation of Unbalanced Voltage Sags and Voltage Unbalance in CIGRE Low Voltage Distribution Network

    OpenAIRE

    Mustafa, Ghullam; Bak-Jensen, Birgitte; Mahat, Pukar; Cecati, Carlo

    2013-01-01

    Any problem with voltage in a power network is undesirable as it aggravates the quality of the power. Power electronic devices such as Voltage Source Converter (VSC) based Static Synchronous Compensator (STATCOM) etc. can be used to mitigate the voltage problems in the distribution system. The voltage problems dealt with in this paper are to show how to mitigate unbalanced voltage sags and voltage unbalance in the CIGRE Low Voltage (LV) test network and net-works like this. The voltage unbala...

  13. Bridge the Digital Divide for Educational Equity

    Science.gov (United States)

    Mason, Christine Y.; Dodds, Richard

    2005-01-01

    Students' technological savvy has challenged schools to make greater use of computers and the Internet in their curricula, but unfortunately, not every student has the same access to it, and the inability to keep pace has created a digital divide that continues to widen. The digital divide particularly affects students who are black, Hispanic,…

  14. Social Welfare Implications of the Digital Divide

    Science.gov (United States)

    Kim, Eunjin; Lee, Byungtae; Menon, Nirup M.

    2009-01-01

    The Internet plays a critical role in informing individuals about society, politics, business, and the environment. So much so that it has been said that the digital divide makes the segment of society on the ''right side'' of the divide (the digitally endowed group) better off and that on the ''wrong side'' (the digitally challenged group) worse…

  15. New Media and the Digital Divide

    NARCIS (Netherlands)

    Deursen, van A.J.A.M.; Dijk, van J.A.G.M.; Wright, James D.

    2015-01-01

    During the 1990s, researchers and policy makers began discussing the presence of a so-called ‘digital divide,’ a distinction of people who do and do not have access to information and communication technologies. The concept of the digital divide stems from a comparative perspective of social and inf

  16. Measurement of a power system nominal voltage, frequency and voltage flicker parameters

    Energy Technology Data Exchange (ETDEWEB)

    Alkandari, A.M. [College of Technological Studies, Electrical Engineering Technology Department, Shwiekh (Kuwait); Soliman, S.A. [Electrical Power and Machines Department, Misr University for Science and Technology, Cairo (Egypt)

    2009-09-15

    We present, in this paper, an approach for identifying the frequency and amplitude of voltage flicker signal that imposed on the nominal voltage signal, as well as the amplitude and frequency of the nominal signal itself. The proposed algorithm performs the estimation in two steps; in the first step the original voltage signal is shifted forward and backward by an integer number of sample, one sample in this paper. The new generated signals from such a shift together with the original one is used to estimate the amplitude of the original signal voltage that composed of the nominal voltage and flicker voltage. The average of this amplitude gives the amplitude of the nominal voltage; this amplitude is subtracted from the original identified signal amplitude to obtain the samples of the flicker voltage. In the second step, the argument of the signal is calculated by simply dividing the magnitude of signal sample with the estimated amplitude in the first step. Calculating the arccosine of the argument, the frequency of the nominal signal as well as the phase angle can be computing using the least error square estimation algorithm. Simulation examples are given within the text to show the features of the proposed approach. (author)

  17. A New Binary Inductive Divider Comparator System for Measuring High-Voltage Thermal Converters

    Science.gov (United States)

    2002-10-01

    use limited to: US Naval Academy. Downloaded on January 30, 2009 at 15:03 from IEEE Xplore . Restrictions apply. Report Documentation Page Form...source, as Authorized licensed use limited to: US Naval Academy. Downloaded on January 30, 2009 at 15:03 from IEEE Xplore . Restrictions apply. KINARD...licensed use limited to: US Naval Academy. Downloaded on January 30, 2009 at 15:03 from IEEE Xplore . Restrictions apply. 1048 IEEE TRANSACTIONS ON

  18. Breakdown voltage of metal-oxide resistors in liquid argon

    CERN Document Server

    Bagby, L F; James, C C; Jones, B J P; Jostlein, H; Lockwitz, S; Naples, D; Raaf, J L; Rameika, R; Schukraft, A; Strauss, T; Weber, M S; Wolbers, S A

    2014-01-01

    We characterized a sample of metal-oxide resistors and measured their breakdown voltage in liquid argon by applying high voltage (HV) pulses over a 3 second period to simulate the electric breakdown in a HV-divider chain. All resistors had higher breakdown voltages in liquid argon than their vendor ratings in air at room temperature. Failure modes range from full destruction to coating damage. In cases where breakdown was not catastrophic, subsequent breakdown voltages were lower in subsequent measuring runs. One resistor type withstands 131\\,kV pulses, the limit of the test setup.

  19. PIV Logon Configuration Guidance

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Glen Alan [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2016-03-04

    This document details the configurations and enhancements implemented to support the usage of federal Personal Identity Verification (PIV) Card for logon on unclassified networks. The guidance is a reference implementation of the configurations and enhancements deployed at the Los Alamos National Laboratory (LANL) by Network and Infrastructure Engineering – Core Services (NIE-CS).

  20. Evaluation of lightning-induced voltages on low-voltage distribution networks

    Energy Technology Data Exchange (ETDEWEB)

    Silveira, Fernando H.; Visacro, Silverio [Federal University of Minas Gerais (LRC/UFMG), Belo Horizonte, MG (Brazil). Lightning Research Center], Emails: silveira@cpdee.ufmg.br, visacro@cpdee.ufmg.br

    2007-07-01

    This paper presents a set of evaluations concerning lightning-induced voltages on low-voltage networks. Such evaluations were performed by means of the Hybrid Electromagnetic Model, a frequency-domain code based on electromagnetic field equations. Sensitivity analyses were developed in order to investigate the role played by the most relevant line parameters on the voltages induced along the electrical system and at the consumer service entrance. The performance of two different low voltage line configurations (conventional versus multiplexed) usually adopted in Brazil was also investigated. The obtained results constitute a contribution to this theme and also provide elements to the development of protection practices to the electrical system and to the consumer against such phenomenon. (author)

  1. Current-voltage characteristics and transition voltage spectroscopy of individual redox proteins.

    Science.gov (United States)

    Artés, Juan M; López-Martínez, Montserrat; Giraudet, Arnaud; Díez-Pérez, Ismael; Sanz, Fausto; Gorostiza, Pau

    2012-12-19

    Understanding how molecular conductance depends on voltage is essential for characterizing molecular electronics devices. We reproducibly measured current-voltage characteristics of individual redox-active proteins by scanning tunneling microscopy under potentiostatic control in both tunneling and wired configurations. From these results, transition voltage spectroscopy (TVS) data for individual redox molecules can be calculated and analyzed statistically, adding a new dimension to conductance measurements. The transition voltage (TV) is discussed in terms of the two-step electron transfer (ET) mechanism. Azurin displays the lowest TV measured to date (0.4 V), consistent with the previously reported distance decay factor. This low TV may be advantageous for fabricating and operating molecular electronic devices for different applications. Our measurements show that TVS is a helpful tool for single-molecule ET measurements and suggest a mechanism for gating of ET between partner redox proteins.

  2. Centrosome positioning in non-dividing cells.

    Science.gov (United States)

    Barker, Amy R; McIntosh, Kate V; Dawe, Helen R

    2016-07-01

    Centrioles and centrosomes are found in almost all eukaryotic cells, where they are important for organising the microtubule cytoskeleton in both dividing and non-dividing cells. The spatial location of centrioles and centrosomes is tightly controlled and, in non-dividing cells, plays an important part in cell migration, ciliogenesis and immune cell functions. Here, we examine some of the ways that centrosomes are connected to other organelles and how this impacts on cilium formation, cell migration and immune cell function in metazoan cells.

  3. Voltage verification unit

    Science.gov (United States)

    Martin, Edward J.

    2008-01-15

    A voltage verification unit and method for determining the absence of potentially dangerous potentials within a power supply enclosure without Mode 2 work is disclosed. With this device and method, a qualified worker, following a relatively simple protocol that involves a function test (hot, cold, hot) of the voltage verification unit before Lock Out/Tag Out and, and once the Lock Out/Tag Out is completed, testing or "trying" by simply reading a display on the voltage verification unit can be accomplished without exposure of the operator to the interior of the voltage supply enclosure. According to a preferred embodiment, the voltage verification unit includes test leads to allow diagnostics with other meters, without the necessity of accessing potentially dangerous bus bars or the like.

  4. High voltage pulse generator. [Patent application

    Science.gov (United States)

    Fasching, G.E.

    1975-06-12

    An improved high-voltage pulse generator is described which is especially useful in ultrasonic testing of rock core samples. An N number of capacitors are charged in parallel to V volts and at the proper instance are coupled in series to produce a high-voltage pulse of N times V volts. Rapid switching of the capacitors from the paralleled charging configuration to the series discharging configuration is accomplished by using silicon-controlled rectifiers which are chain self-triggered following the initial triggering of the first rectifier connected between the first and second capacitors. A timing and triggering circuit is provided to properly synchronize triggering pulses to the first SCR at a time when the charging voltage is not being applied to the parallel-connected charging capacitors. The output voltage can be readily increased by adding additional charging networks. The circuit allows the peak level of the output to be easily varied over a wide range by using a variable autotransformer in the charging circuit.

  5. First high-voltage measurements using Ca{sup +} ions at the ALIVE experiment

    Energy Technology Data Exchange (ETDEWEB)

    König, K., E-mail: kkoenig@ikp.tu-darmstadt.de [Technische Universität Darmstadt, Institut für Kernphysik (Germany); Geppert, Ch. [Universität Mainz, Institut für Kernchemie (Germany); Krämer, J.; Maaß, B. [Technische Universität Darmstadt, Institut für Kernphysik (Germany); Otten, E. W. [Universität Mainz, Institut für Physik (Germany); Ratajczyk, T.; Nörtershäuser, W. [Technische Universität Darmstadt, Institut für Kernphysik (Germany)

    2017-11-15

    Many physics experiments depend on accurate high-voltage measurements to determine for example the exact retardation potential of an electron spectrometer as in the KATRIN experiment or the acceleration voltage of the ions at ISOL facilities. Until now only precision high-voltage dividers can be used to measure voltages up to 65 kV with an accuracy of 1 ppm. However, these dividers need frequent calibration and cross-checking and the direct traceability is not given. In this article we will describe the status of an experiment which aims to measure high voltages using collinear laser spectroscopy and which has the potential to provide a high-voltage standard and hence, a calibration source for precision high-voltage dividers on the 1 ppm level.

  6. Americans Divided Over Organic, GM Foods: Poll

    Science.gov (United States)

    ... gov/news/fullstory_162314.html Americans Divided Over Organic, GM Foods: Poll Their opinions aren't driven by politics ... News) -- Americans are split on the value of organic foods and concerns about genetically modified (GM) foods, a ...

  7. Environmental Aesthetics. Crossing Divides and Breaking Ground

    NARCIS (Netherlands)

    Drenthen, M.; Keulartz, J.

    2014-01-01

    Environmental aesthetics crosses several commonly recognized divides: between analytic and continental philosophy, Eastern and Western traditions, universalizing and historicizing approaches, and theoretical and practical concerns. This volume sets out to show how these,perspectives can be brought i

  8. Energy conserving effects of dividing wall column☆

    Institute of Scientific and Technical Information of China (English)

    Jing Fang; Hanmei Zhao; Jianchao Qi; Chunli Li; Junjie Qi; Jiajia Guo

    2015-01-01

    The energy-conserving performance of dividing wal column (DWC) is discussed in this paper. The heat transfer through the dividing wall is considered and the results are compared with that of common heat insulation dividing wall column (HIDWC). Based on the thermodynamic analysis of heat transfer dividing wall column (HTDWC) and HIDWC, both computer simulation and experiments are employed to analyze the energy-conserving situation. Mixtures of n-hexane, n-heptane and n-octane are chosen as the example for separation. The results show that the energy consumption of HTDWC is 50.3%less than that of conventional distillation column, while it is 46.4% less than that of HIDWC. It indicates that DWC is efficient on separating three-component mixtures and HTDWC can save more energy than HIDWC. Thus it is necessary to consider the heat transfer while applying DWC to industry.

  9. Global Value Chain Configuration

    DEFF Research Database (Denmark)

    Hernandez, Virginia; Pedersen, Torben

    2017-01-01

    This paper reviews the literature on global value chain configuration, providing an overview of this topic. Specifically, we review the literature focusing on the concept of the global value chain and its activities, the decisions involved in its configuration, such as location, the governance...... modes chosen and the different ways of coordinating them. We also examine the outcomes of a global value chain configuration in terms of performance and upgrading. Our aim is to review the state of the art of these issues, identify research gaps and suggest new lines for future research that would...

  10. Planar multijunction high voltage solar cells

    Science.gov (United States)

    Evans, J. C., Jr.; Chai, A. T.; Goradia, C.

    1980-01-01

    Technical considerations, preliminary results, and fabrication details are discussed for a family of high-voltage planar multi-junction (PMJ) solar cells which combine the attractive features of planar cells with conventional or interdigitated back contacts and the vertical multijunction (VMJ) solar cell. The PMJ solar cell is internally divided into many voltage-generating regions, called unit cells, which are internally connected in series. The key to obtaining reasonable performance from this device was the separation of top surface field regions over each active unit cell. Using existing solar cell fabricating methods, output voltages in excess of 20 volts per linear centimeter are possible. Analysis of the new device is complex, and numerous geometries are being studied which should provide substantial benefits in both normal sunlight usage as well as with concentrators.

  11. Airport Configuration Prediction Project

    Data.gov (United States)

    National Aeronautics and Space Administration — There is presently poor knowledge throughout the National Airspace System (NAS) of the airport configurations currently in use at each airport. There is even less...

  12. The LHCb configuration database

    CERN Document Server

    Abadie, Lana; Gaspar, Clara; Jacobsson, Richard; Jost, Beat; Neufeld, Niko

    2005-01-01

    The Experiment Control System (ECS) will handle the monitoring, configuration and operation of all the LHCb experimental equipment. All parameters required to configure electronics equipment under the control of the ECS will reside in a configuration database. The database will contain two kinds of information: 1.\tConfiguration properties about devices such as hardware addresses, geographical location, and operational parameters associated with particular running modes (dynamic properties). 2.\tConnectivity between devices : this consists of describing the output and input connections of a device (static properties). The representation of these data using tables must be complete so that it can provide all the required information to the ECS and must cater for all the subsystems. The design should also guarantee a fast response time, even if a query results in a large volume of data being loaded from the database into the ECS. To fulfil these constraints, we apply the following methodology: Determine from the d...

  13. Firewall Configuration Errors Revisited

    CERN Document Server

    Wool, Avishai

    2009-01-01

    The first quantitative evaluation of the quality of corporate firewall configurations appeared in 2004, based on Check Point FireWall-1 rule-sets. In general that survey indicated that corporate firewalls were often enforcing poorly written rule-sets, containing many mistakes. The goal of this work is to revisit the first survey. The current study is much larger. Moreover, for the first time, the study includes configurations from two major vendors. The study also introduce a novel "Firewall Complexity" (FC) measure, that applies to both types of firewalls. The findings of the current study indeed validate the 2004 study's main observations: firewalls are (still) poorly configured, and a rule-set's complexity is (still) positively correlated with the number of detected risk items. Thus we can conclude that, for well-configured firewalls, ``small is (still) beautiful''. However, unlike the 2004 study, we see no significant indication that later software versions have fewer errors (for both vendors).

  14. Drupal 8 configuration management

    CERN Document Server

    Borchert, Stefan

    2015-01-01

    Drupal 8 Configuration Management is intended for people who use Drupal 8 to build websites, whether you are a hobbyist using Drupal for the first time, a long-time Drupal site builder, or a professional web developer.

  15. ATLAS DAQ Configuration Databases

    Institute of Scientific and Technical Information of China (English)

    I.Alexandrov; A.Amorim; 等

    2001-01-01

    The configuration databases are an important part of the Trigger/DAQ system of the future ATLAS experiment .This paper describes their current status giving details of architecture,implementation,test results and plans for future work.

  16. Configuration Management Automation (CMA) -

    Data.gov (United States)

    Department of Transportation — Configuration Management Automation (CMA) will provide an automated, integrated enterprise solution to support CM of FAA NAS and Non-NAS assets and investments. CMA...

  17. Configuration by Modularisation

    DEFF Research Database (Denmark)

    Riitahuhta, Asko; Andreasen, Mogens Myrup

    1998-01-01

    Globally operating companies have realized that locally customized products and services are today the prerequisite for the success. The capability or the paradigm to act locally in global markets is called Mass Customization [Victor 1997]. The prerequisite for Mass Customization is Configuration...... for the creation of a structured product family is presented and examples are given. The concepts of a novel Dynamic Modularisation method, Metrics for Modularisation and Design for Configurability are presented....

  18. Optical voltage sensors: principle, problem and research proposal

    Science.gov (United States)

    Li, Changsheng

    2016-10-01

    Sensing principles and main problems to be solved for optical voltage sensors are briefly reviewed. Optical effects used for voltage sensing usually include electro-optic Pockels and Kerr effects, electro-gyration effect, elasto-optical effect, and electroluminescent effects, etc. In principle, typical optical voltage sensor is based on electro-optic Pockels crystals and closed-loop signal detection scheme. Main problems to be solved for optical voltage sensors include: how to remove influence of unwanted multiple optical effects on voltage sensing performance; how to select or develop a proper voltage sensing material and element; how to keep optical phase bias to be stable under temperature fluctuation and vibration; how to achieve dc voltage sensing, etc. In order to suppress the influence of unwanted optical effects and light beam coupling-related loss on voltage sensing signals, we may pay more attention to all-fiber and waveguide voltage sensors. Voltage sensors based on electroluminescent effects are also promising in some application fields due to their compact configuration, low cost and potential long-term reliability.

  19. Design & Implementation of Zero Voltage Switching Buck Converter

    Directory of Open Access Journals (Sweden)

    A.Suresh Kumar

    2014-09-01

    Full Text Available Zero voltage switching (ZVS buck converter is more preferable over hard switched buck converter for low power, high frequency DC-DC conversion applications. In Zero voltage switching converter, turn on & turn off of a switch occurs at zero voltage that results in lower switching losses. In this converter soft switching is achieved by using resonant components. The optimal values of resonant components are determined by using electric functions derived from circuit configuration. This type of soft switched resonant converter offers very low electromagnetic interference (EMI.This study presents the circuit configuration with least components to realize highly efficient zero voltage switching resonant converter. It’s feasibility is confirmed with the developed proto type model and experimental results are verified.

  20. Orbital angular momentum divider of light

    CERN Document Server

    Dong, Hailong Zhou Jianji; Cai, Xinlun; Yu, SiYuan; Zhang, Xinliang

    2016-01-01

    Manipulation of orbital angular momentum (OAM) of light is essential in OAM-based optical systems. Especially, OAM divider, which can convert the incoming OAM mode into one or several new smaller modes in proportion at different spatial paths, is very useful in OAM-based optical networks. However, this useful tool was never reported yet. For the first time, we put forward a passive OAM divider based on coordinate transformation. The device consists of a Cartesian to log-polar coordinate converter and an inverse converter. The first converter converts the OAM light into a rectangular-shaped plane light with a transverse phase gradient. And the second converter converts the plane light into multiple diffracted light. The OAM of zeroth-order diffracted light is the product of the input OAM and the scaling parameter. The residual light is output from other diffracted orders. Furthermore, we extend the scheme to realize equal N-dividing of OAM and arbitrary dividing of OAM. The ability of dividing OAM shows huge p...

  1. High Voltage Distribution

    Science.gov (United States)

    Norbeck, Edwin; Miller, Michael; Onel, Yasar

    2010-11-01

    For detector arrays that require 5 to 10 kV at a few microamps each for hundreds of detectors, using hundreds of HV power supplies is unreasonable. Bundles of hundreds of HV cables take up space that should be filled with detectors. A typical HV module can supply 1 ma, enough current for hundreds of detectors. It is better to use a single HV module and distribute the current as needed. We show a circuit that, for each detector, measures the current, cuts off the voltage if the current exceeds a set maximum, and allows the HV to be turned on or off from a control computer. The entire array requires a single HV cable and 2 or 3 control lines. This design provides the same voltage to all of the detectors, the voltage set by the single HV module. Some additional circuitry would allow a computer controlled voltage drop between the HV and each individual detector.

  2. Dynamic airspace configuration by genetic algorithm

    Directory of Open Access Journals (Sweden)

    Marina Sergeeva

    2017-06-01

    Full Text Available With the continuous air traffic growth and limits of resources, there is a need for reducing the congestion of the airspace systems. Nowadays, several projects are launched, aimed at modernizing the global air transportation system and air traffic management. In recent years, special interest has been paid to the solution of the dynamic airspace configuration problem. Airspace sector configurations need to be dynamically adjusted to provide maximum efficiency and flexibility in response to changing weather and traffic conditions. The main objective of this work is to automatically adapt the airspace configurations according to the evolution of traffic. In order to reach this objective, the airspace is considered to be divided into predefined 3D airspace blocks which have to be grouped or ungrouped depending on the traffic situation. The airspace structure is represented as a graph and each airspace configuration is created using a graph partitioning technique. We optimize airspace configurations using a genetic algorithm. The developed algorithm generates a sequence of sector configurations for one day of operation with the minimized controller workload. The overall methodology is implemented and successfully tested with air traffic data taken for one day and for several different airspace control areas of Europe.

  3. Ac Synchronous Servo Based On The Armature Voltage Prediction Model

    Science.gov (United States)

    Hoshino, Akihiro; Kuromaru, Hiroshi; Kobayashi, Shinichi

    1987-10-01

    A new control method of the AC synchro-nous servo-system (Brushless DC servo-system) is discussed. The new system is based on the armature voltage prediction model. Without a resolver-digital-conver-ter nor a tachometer-generator, the resolver provides following three signals to the system immediately, they are the current command, the induced voltage, and the rotor speed. The new method realizes a simple hardware configuration. Experimental results show a good performance of the system.

  4. High voltage engineering fundamentals

    CERN Document Server

    Kuffel, E; Hammond, P

    1984-01-01

    Provides a comprehensive treatment of high voltage engineering fundamentals at the introductory and intermediate levels. It covers: techniques used for generation and measurement of high direct, alternating and surge voltages for general application in industrial testing and selected special examples found in basic research; analytical and numerical calculation of electrostatic fields in simple practical insulation system; basic ionisation and decay processes in gases and breakdown mechanisms of gaseous, liquid and solid dielectrics; partial discharges and modern discharge detectors; and over

  5. Reference frame for Product Configuration

    DEFF Research Database (Denmark)

    Ladeby, Klaes Rohde; Oddsson, Gudmundur Valur

    2011-01-01

    on configuration systems in the shape of anecdotal reporting on the development of information systems that perhaps support the configuration task – perhaps not. Consequently, the definition of configuration has become ambiguous as different research groups defines configuration differently. This paper propose...... a reference frame for configuration that permits 1) a more precise understanding of a configuration system, 2) a understanding of how the configuration system relate to other systems, and 3) a definition of the basic concepts in configuration. The total configuration system, together with the definition...

  6. Low-voltage gyrotrons

    Science.gov (United States)

    Glyavin, M. Yu.; Zavolskiy, N. A.; Sedov, A. S.; Nusinovich, G. S.

    2013-03-01

    For a long time, the gyrotrons were primarily developed for electron cyclotron heating and current drive of plasmas in controlled fusion reactors where a multi-megawatt, quasi-continuous millimeter-wave power is required. In addition to this important application, there are other applications (and their number increases with time) which do not require a very high power level, but such issues as the ability to operate at low voltages and have compact devices are very important. For example, gyrotrons are of interest for a dynamic nuclear polarization, which improves the sensitivity of the nuclear magnetic resonance spectroscopy. In this paper, some issues important for operation of gyrotrons driven by low-voltage electron beams are analyzed. An emphasis is made on the efficiency of low-voltage gyrotron operation at the fundamental and higher cyclotron harmonics. These efficiencies calculated with the account for ohmic losses were, first, determined in the framework of the generalized gyrotron theory based on the cold-cavity approximation. Then, more accurate, self-consistent calculations for the fundamental and second harmonic low-voltage sub-THz gyrotron designs were carried out. Results of these calculations are presented and discussed. It is shown that operation of the fundamental and second harmonic gyrotrons with noticeable efficiencies is possible even at voltages as low as 5-10 kV. Even the third harmonic gyrotrons can operate at voltages about 15 kV, albeit with rather low efficiency (1%-2% in the submillimeter wavelength region).

  7. Bridging the digital divide with mobile services

    CERN Document Server

    Yelton, Andromeda

    2013-01-01

    In this issue of Library Technology Reports, Andromeda Yelton shows how libraries can build on the breadth of this population to help bridge the digital divide and provide even greater access to information. Yelton breaks down the demographics of mobile internet users, provides examples of how different libraries are reaching out to these populations, and suggests what the future may hold for this trend.

  8. Digital divide research, achievements and shortcomings

    NARCIS (Netherlands)

    Dijk, van Jan A.G.M.

    2006-01-01

    From the end of the 1990s onwards the digital divide, commonly defined as the gap between those who have and do not have access to computers and the Internet, has been a central issue on the scholarly and political agenda of new media development. This article makes an inventory of 5 years of digita

  9. The electronic health record: a digital divide?

    Science.gov (United States)

    Glaser, John

    2007-10-01

    The gap between EHR adoption among larger providers versus adoption by smaller or rural providers has caused a "digital divide" that could threaten smaller providers' survival in the years ahead. Closing this gap will require the collective action of providers, payers, and government.

  10. Digital divide research, achievements and shortcomings

    NARCIS (Netherlands)

    van Dijk, Johannes A.G.M.

    2006-01-01

    From the end of the 1990s onwards the digital divide, commonly defined as the gap between those who have and do not have access to computers and the Internet, has been a central issue on the scholarly and political agenda of new media development. This article makes an inventory of 5 years of

  11. Young People's Internet Use: Divided or Diversified?

    Science.gov (United States)

    Boonaert, Tom; Vettenburg, Nicole

    2011-01-01

    This article critically analyses research on young people's internet use. Based on a literature analysis, it examines which young people do what on the internet. These results invite a reflection on the dominant discourse on the digital divide. Within this discourse, there is a strong focus on the use of the internet for information purposes only,…

  12. Democratisation and Conflict in Ethnically Divided Societies

    NARCIS (Netherlands)

    Vorrath, Judith; Krebs, Lutz

    2009-01-01

    This article reviews three important factors in the academic debate on ethnic civil wars: the role of ethnicity in causing and structuring violence, the spread of ethnic civil wars once they have started, and the influence of democratic transitions in divided societies. The review displays the range

  13. Configuration Control Office

    CERN Multimedia

    Beltramello, O

    In order to enable Technical Coordination to manage the detector configuration and to be aware of all changes in this configuration, a baseline of the envelopes has been created in April 2001. Fifteen system and multi-system envelope drawings have been approved and baselined. An EDMS file is associated with each approved envelope, which provides a list of the current known unsolved conflicts related to the envelope and a list of remaining drawing inconsistencies to be corrected. The envelope status with the associated drawings and EDMS file can be found on the web at this adress: http://atlasinfo.cern.ch/Atlas/TCOORD/Activities/Installation/Configuration/ Any modification in the baseline has to be requested via the Engineering Change Requests. The procedure can be found under: http://atlasinfo.cern.ch/Atlas/TCOORD/Activities/TcOffice/Quality/ECR/ TC will review all the systems envelopes in the near future and manage conflict resolution with the collaboration of the systems.

  14. The LHCb configuration database

    CERN Document Server

    Abadie, L; Van Herwijnen, Eric; Jacobsson, R; Jost, B; Neufeld, N

    2005-01-01

    The aim of the LHCb configuration database is to store information about all the controllable devices of the detector. The experiment's control system (that uses PVSS ) will configure, start up and monitor the detector from the information in the configuration database. The database will contain devices with their properties, connectivity and hierarchy. The ability to store and rapidly retrieve huge amounts of data, and the navigability between devices are important requirements. We have collected use cases to ensure the completeness of the design. Using the entity relationship modelling technique we describe the use cases as classes with attributes and links. We designed the schema for the tables using relational diagrams. This methodology has been applied to the TFC (switches) and DAQ system. Other parts of the detector will follow later. The database has been implemented using Oracle to benefit from central CERN database support. The project also foresees the creation of tools to populate, maintain, and co...

  15. Device for monitoring cell voltage

    Science.gov (United States)

    Doepke, Matthias [Garbsen, DE; Eisermann, Henning [Edermissen, DE

    2012-08-21

    A device for monitoring a rechargeable battery having a number of electrically connected cells includes at least one current interruption switch for interrupting current flowing through at least one associated cell and a plurality of monitoring units for detecting cell voltage. Each monitoring unit is associated with a single cell and includes a reference voltage unit for producing a defined reference threshold voltage and a voltage comparison unit for comparing the reference threshold voltage with a partial cell voltage of the associated cell. The reference voltage unit is electrically supplied from the cell voltage of the associated cell. The voltage comparison unit is coupled to the at least one current interruption switch for interrupting the current of at least the current flowing through the associated cell, with a defined minimum difference between the reference threshold voltage and the partial cell voltage.

  16. Nationality Divides and Shared Leadership in Multinational Teams

    DEFF Research Database (Denmark)

    Paunova, Minna

    2015-01-01

    nationality-based characteristics of members may divide teams and affect leadership. We argue that the national belonging of members may result in both identity subgroups and status ranks. However, the configurational properties of identity subgroups and status ranks will have distinct effects on team......How shared leadership is enacted in teams that are nationally diverse is currently under- researched, despite the increasing presence of multinational teams in the workplace. To better understand the phenomenon of shared leadership in multinational team contexts, we propose two ways in which...... dynamics, shared leadership within the team, and team performance. We conduct two empirical studies, and find that the number and balance of identity subgroups have important implications for multinational team functioning, in line with social identity approaches. Interestingly, the number and balance...

  17. Evolution of a Voltage-Time Model of Thermal Batteries

    Science.gov (United States)

    1991-02-01

    MARK I1 VOLTAGE-TIME MODEL 7 6 MARKt III VOLTAGE-TIME MODEL 10 6.1 Capacity degradation II 6,2 Allowance ’for time-dependent polarisation If 6,3...period is sub- divided into two or more segments in the model input data, in all of which the TM MS 1163 13 same current or resistor value operates as

  18. Conquering the digital divide: Botswana and South Korea digital divide status and interventions

    Directory of Open Access Journals (Sweden)

    Nonofo C. Sedimo

    2011-03-01

    Full Text Available Background: Botswana is putting in place initiatives towards establishing itself as a knowledgebased economy. Transformation from a resource-based to a knowledge-based economy is partly hinged on innovation, research and development capability, knowledge channels, and the funding of research and development activities.Objectives: Bridging the digital divide and narrowing the intra-national divide brings about global information and communication technology (ICT usage that translates into changing work patterns and eventually transformed economies. This article outlines the different interventions implemented in Botswana to bridge the divide. The South Korean experience in bridging the divide is discussed so as to serve as lessons on how to effectively bridge the divide to Botswana’s initiatives.Method: Using a mix of exploratory and empirical study, this article presents the findings on the status of ICT uptake in Botswana and investigates the level of the digital divide in the country.Results: The results of the study show that the digital divide is much more evident in Botswana than in South Korea. South Korea has put in place robust strategic initiatives towards reducing the digital divide and this has largely transcended into its transformation into a full-fledged knowledge society.Conclusion: This article is timely as it unearths the different pointers that may be utilised in policy formation and what interventions need to be taken at both the individual and national level to bridge the digital divide.

  19. Ansible configuration management

    CERN Document Server

    Hall, Daniel

    2015-01-01

    This book is intended for anyone who wants to learn Ansible starting from the basics. Some experience of how to set up and configure Linux machines and a working knowledge of BIND, MySQL, and other Linux daemons is expected.

  20. DNS BIND Server Configuration

    Directory of Open Access Journals (Sweden)

    Radu MARSANU

    2011-01-01

    Full Text Available After a brief presentation of the DNS and BIND standard for Unix platforms, the paper presents an application which has a principal objective, the configuring of the DNS BIND 9 server. The general objectives of the application are presented, follow by the description of the details of designing the program.

  1. Inclusive Services Innovation Configuration

    Science.gov (United States)

    Holdheide, Lynn R.; Reschly, Daniel J.

    2011-01-01

    Teacher preparation to deliver inclusive services to students with disabilities is increasingly important because of changes in law and policy emphasizing student access to, and achievement in, the general education curriculum. This innovation configuration identifies the components of inclusive services that should be incorporated in teacher…

  2. Analyzing Broadband Divide in the Farming Sector

    DEFF Research Database (Denmark)

    Jensen, Michael; Gutierrez Lopez, Jose Manuel; Pedersen, Jens Myrup

    2013-01-01

    Agriculture industry has been evolving for centuries. Currently, the technological development of Internet oriented farming tools allows to increase the productivity and efficiency of this sector. Many of the already available tools and applications require high bandwidth in both directions......, upstream and downstream connection. The main constraint is that farms are naturally located in rural areas where the required access broadband data rates are not available. This paper studies the broadband divide in relation to the Danish agricultural sector. Results show how there is an important...... difference between the broadband availability for farms and the rest of the households/buildings the country. This divide may be slowing down the potential technological development of the farming industry, in order to keep their competitiveness in the market. Therefore, broadband development in rural areas...

  3. Divided or kissing nevus of the penis.

    Science.gov (United States)

    Hardin, Carolyn A; Tieu, Kathy D

    2013-10-16

    The divided or kissing nevus is an unusual congenital melanocytic nevus. By definition, these nevi appear on skin that separates during embryological development. These lesions have been reported on the eyelids, fingers, and rarely the penis. We describe an 18 year old uncircumcised male who presented with an asymptomatic darkly pigmented patch on the glans penis. He reported that the lesion had appeared recently and was enlarging. Physical examination revealed a second symmetric lesion on the adjacent foreskin. Punch biopsy of the lesion on the glans penis showed abundant intradermal melanocytes devoid of mitoses and atypia, consistent with an intradermal melanocytic nevus. Based on the benign histologic nature and clinical exam, the lesion was diagnosed as a divided or kissing nevus of the penis. Proposed treatments include excision and grafting as well as Nd:YAG laser therapy. However, these patients may be safely monitored with regular follow-up skin examinations because there is minimal risk of malignant transformation.

  4. Voltage Regulators for Photovoltaic Systems

    Science.gov (United States)

    Delombard, R.

    1986-01-01

    Two simple circuits developed to provide voltage regulation for highvoltage (i.e., is greater than 75 volts) and low-voltage (i.e., is less than 36 volts) photovoltaic/battery power systems. Use of these circuits results in voltage regulator small, low-cost, and reliable, with very low power dissipation. Simple oscillator circuit controls photovoltaic-array current to regulate system voltage and control battery charging. Circuit senses battery (and system) voltage and adjusts array current to keep battery voltage from exceeding maximum voltage.

  5. Divided libraries remodeling management to unify institutions

    CERN Document Server

    Webb, TD

    2012-01-01

    Given the highly trained library workforce now available and the vast and growing array of packaging information and knowledge, libraries have the capacity to become pre-eminent places of learning, research, and teaching. Yet, despite this potential, libraries remain divided from their constituencies and their governing bodies, be they students, faculties, university administrations, municipal governments, or ordinary citizens. Indeed, many modern university administrators, viewing librarians as ancillary citizens in academe, have allowed their libraries to wither under the burden of shrinking

  6. Nursing's divided loyalties: an historical case study.

    Science.gov (United States)

    Baer, E D

    1989-01-01

    Using the historical version of the case study method, this research explored an example of turn-of-the-century nurses' conflicted loyalties. One training school alumnae association was examined to demonstrate that nurses acted out simultaneous loyalty to competing entities: individual graduates attributes vs. associational eligibility requirements; member vs. institutions' needs; and local vs. national nursing concerns. As a result of these divided loyalties, the nurses did not meet the alumnae organizational goals they set for themselves.

  7. Self-organization of divided hierarchy

    Science.gov (United States)

    Odagaki, Takashi; Kitada, Keigo; Omizo, Kenta; Fujie, Ryo

    2015-03-01

    There are two types of extreme form of hierarchy, one is the plutonomy where small fraction of winners and losers and many people in the middle class appear and the other a divided hierarchy where half of population become winners and the remaining half become losers. We study the emergence of the divided hierarchy in a model society which consists of bellicose individuals who always try to fight and fight with the strongest neighbor and pacific individuals who always try not to fight and when necessary fight with the weakest neighbor. In our model society, (1) individuals make random walk on a square lattice, (2) when two individuals encounter they fight each other and (3) the winner deprives wealth from the loser. By a Monte Carlo simulation, we show that there are two transitions when the population density is increased; one is a transition from the egalitarian society to a hierarchical society I where winners, losers and middle classes coexist and the other is a transition from the hierarchical society I to a hierarchical society II where winners and losers exist but no middle classes exist, that is the divided hierarchy. We also show that clusters consisting mostly of bellicose individuals appear in the hierarchical society I.

  8. Studying Voltage Transformer Ferroresonance

    Directory of Open Access Journals (Sweden)

    Hamid Radmanesh

    2012-09-01

    Full Text Available This study studies the effect of Circuit Breaker Shunt Resistance (CBSR, Metal Oxide Vaistor (MOV and Neutral earth Resistance (NR on the control of ferroresonance in the voltage transformer. It is expected that NR can controlled ferroresonance better than MOV and CBSR. Study has been done on a one phase voltage transformer rated 100 VA, 275 kV. The simulation results reveal that considering the CBSR and MOV exhibits a great mitigating effect on ferroresonance overvoltages, but these resistances cannot control these phenomena for all range of parameters. By applying NR to the system structure, ferroresonance has been controlled and its amplitude has been damped for all parameters values.

  9. Splicing the Divide: A Review of Research on the Evolving Digital Divide among K-12 Students

    Science.gov (United States)

    Dolan, Jennifer E.

    2016-01-01

    The digital divide has narrowed with regard to one definition of access to technology--the binary view of the "haves" and "have-nots." However, use of technology at home and in school is not equitable for all students. According to recent literature, a broader and more nuanced definition of the technological divide is necessary…

  10. Breakdown voltage of metal-oxide resistors in liquid argon

    Energy Technology Data Exchange (ETDEWEB)

    Bagby, L. F. [Fermilab; Gollapinni, S. [Kansas State U.; James, C. C. [Fermilab; Jones, B. J.P. [MIT; Jostlein, H. [Fermilab; Lockwitz, S. [Fermilab; Naples, D. [Pittsburgh U.; Raaf, J. L. [Fermilab; Rameika, R. [Fermilab; Schukraft, A. [Fermilab; Strauss, T. [Bern U., LHEP; Weber, M. S. [Bern U., LHEP; Wolbers, S. A. [Fermilab

    2014-11-07

    We characterized a sample of metal-oxide resistors and measured their breakdown voltage in liquid argon by applying high voltage (HV) pulses over a 3 second period. This test mimics the situation in a HV-divider chain when a breakdown occurs and the voltage across resistors rapidly rise from the static value to much higher values. All resistors had higher breakdown voltages in liquid argon than their vendor ratings in air at room temperature. Failure modes range from full destruction to coating damage. In cases where breakdown was not catastrophic, subsequent breakdown voltages were lower in subsequent measuring runs. One resistor type withstands 131 kV pulses, the limit of the test setup.

  11. High voltage testing for the MAJORANA Demonstrator

    CERN Document Server

    Abgrall, N; Avignone, F T; Barabash, A S; Bertrand, F E; Bradley, A W; Brudanin, V; Busch, M; Buuck, M; Byram, D; Caldwell, A S; Chan, Y-D; Christofferson, C D; Chu, P -H; Cuesta, C; Detwiler, J A; Doe, P J; Dunagan, C; Efremenko, Yu; Ejiri, H; Elliott, S R; Fu, Z; Galindo-Uribarri, A; Giovanetti, G K; Goett, J; Green, M P; Gruszko, J; Guinn, I S; Guiseppe, V E; Henning, R; Hoppe, E W; Howard, S; Howe, M A; Jasinski, B R; Keeter, K J; Kidd, M F; Konovalov, S I; Kouzes, R T; LaFerriere, B D; Leon, J; Li, A; MacMullin, J; Martin, R D; Massarczyk, R; Meijer, S J; Mertens, S; Orrell, J L; O'Shaughnessy, C; Poon, A W P; Radford, D C; Rager, J; Rielage, K; Robertson, R G H; Romero-Romero, E; Shanks, B; Shirchenko, M; Snyder, N; Suriano, A M; Tedeschi, D; Thompson, A; Ton, K T; Trimble, J E; Varner, R L; Vasilyev, S; Vetter, K; Vorren, K; White, B R; Wilkerson, J F; Wiseman, C; Xu, W; Yakushev, E; Yu, C -H; Yumatov, V

    2016-01-01

    The MAJORANA Collaboration is constructing the MAJORANA Demonstrator, an ultra-low background, 44-kg modular high-purity Ge (HPGe) detector array to search for neutrinoless double-beta decay in Ge-76. The phenomenon of surface micro-discharge induced by high-voltage has been studied in the context of the MAJORANA Demonstrator. This eff?ect can damage the front-end electronics or mimic detector signals. To ensure the correct performance, every high-voltage cable and feedthrough must be capable of supplying HPGe detector operating voltages as high as 5 kV without exhibiting discharge. R&D measurements were carried out to understand the testing system and determine the optimum design configuration of the high-voltage path, including diff?erent improvements of the cable layout and feedthrough flange model selection. Every cable and feedthrough to be used at the MAJORANA Demonstrator was characterized and the micro-discharge eff?ects during the MAJORANA Demonstrator commissioning phase were studied. A stable c...

  12. Proposed Novel Multiphase-Multilevel Inverter Configuration for Open-End Winding Loads

    DEFF Research Database (Denmark)

    Padamanaban, Sanjeevi Kumar; Wheeler, Patrick; Blaabjerg, Frede

    2016-01-01

    This paper presents a new multiphase-multilevel inverter configuration for open-winding loads and suitable for medium power (low-voltage/high-current) applications such as `More Electric Aircraft'. Modular structure comprised of standard dual three-phase voltage source inverter (VSI) along with o...

  13. Three-phase multilevel inverter configuration for open-winding high power application

    DEFF Research Database (Denmark)

    Sanjeevikumar, Padmanaban; Blaabjerg, Frede; Wheeler, Patrick William

    2015-01-01

    This paper work exploits a new dual open-winding three-phase multilevel inverter configuration suitable for high power medium-voltage applications. Modular structure comprised of standard three-phase voltage source inverter (VSI) along with one additional bi-directional semiconductor device (MOSF...

  14. Using Dividing Wall Columns (DWC) in LNG Production: deviding wall column, double dividing wall column, prefractionator arrangement, Petlyuk column, NGL recovery, distillation

    OpenAIRE

    Ashrafian, Roohollah

    2014-01-01

    The Dividing Wall Columns (DWC) distillation has attracted growing interest for fractionation of multicomponent mixture due to reduction of energy consumption, auxiliary equipment and space within fractionation process. Recent developments of the process show considerable energy saving, up to 30%-40%, compared to conventional fractionation schemes. The objective of this thesis is to introduce DWC configurations, governing equations and applications in LNG and gas processing as well as explana...

  15. VOLTAGE REGULATORS ASYNCHRONOUS GENERATORS

    Directory of Open Access Journals (Sweden)

    Grigorash O. V.

    2015-06-01

    Full Text Available A promising is currently the use of asynchronous generators with capacitive excitation as a source of electricity in stand-alone power systems. Drive asynchronous generators may exercise as a thermal engine and wind wheel wind power plant or turbines of small hydropower plants. The article discusses the structural and schematics of voltage stabilizers and frequency of asynchronous generators with improved operational and technical specifications. Technical novelty of design solutions of the magnetic system and stabilizers asynchronous generator of electricity parameters confirmed by the patents for the invention of the Russian Federation. The proposed technical solution voltage stabilizer asynchronous generators, can reduce the weight of the block capacitors excitation and reactive power compensation, as well as to simplify the control system power circuit which has less power electronic devices. For wind power plants it is an important issue not only to stabilize the voltage of the generator, but also the frequency of the current. Recommend functionality stabilizer schemes parameters of electric power made for direct frequency converters with artificial and natural switching power electronic devices. It is also proposed as part of stabilization systems use single-phase voltage, three-phase transformers with rotating magnetic field, reduce the level of electromagnetic interference generated by power electronic devices for switching, enhance the efficiency and reliability of the stabilizer.

  16. Geomagnetism and Induced Voltage

    Science.gov (United States)

    Abdul-Razzaq, W.; Biller, R. D.

    2010-01-01

    Introductory physics laboratories have seen an influx of "conceptual integrated science" over time in their classrooms with elements of other sciences such as chemistry, biology, Earth science, and astronomy. We describe a laboratory to introduce this development, as it attracts attention to the voltage induced in the human brain as it…

  17. Modular small hydro configuration

    Science.gov (United States)

    1981-09-01

    Smaller sites (those under 750 kilowatts) which previously were not attractive to develop using equipment intended for application at larger scale sites, were the focal point in the conception of a system which utilizes standard industrial components which are generally available within short procurement times. Such components were integrated into a development scheme for sites having 20 feet to 150 feet of head. The modular small hydro configuration maximizes the use of available components and minimizes modification of existing civil works. A key aspect of the development concept is the use of a vertical turbine multistage pump, used in the reverse mode as a hydraulic turbine. The configuration allows for automated operation and control of the hydroelectric facilities with sufficient flexibility for inclusion of potential hydroelectric sites into dispersed storage and generation (DSG) utility grid systems.

  18. Low input voltage converter/regulator minimizes external disturbances

    Science.gov (United States)

    1966-01-01

    Low-input voltage converter/regulator constructed in a coaxial configuration minimizes external magnetic field disturbance, suppresses radio noise interference, and provides excellent heat transfer from power transistors. It converts the output of fuel and solar cells, thermionic diodes, thermoelectric generators, and electrochemical batteries to a 28 V dc output.

  19. Polysoaps: Configurations and Elasticity

    Science.gov (United States)

    Halperin, A.

    1997-03-01

    Simple polymers are very long, flexible, linear molecules. Amphiphiles, soaps, are small molecules comprising of a part that prefers water over oil and a part that prefers oil over water. By combining the two we arrive at an interesting, little explored, class of materials: Polysoaps. These comprise of a water soluble backbone incorporating, at intervals, covalently bound amphiphilic monomers. In water, the polymerised amphiphiles aggregate into self assembled units known as micelles. This induces a dramatic modification of the spatial configurations of the polymers. What were featureless random coils now exhibit intramolecular, hierachial self organisation. Due to this self organisation it is necessary to modify the paradigms describing the large scale behaviour of these polymers: Their configurations, dimensions and elasticity. Understanding the behaviour of these polymers is of practical interest because of their wide range of industrial applications, ranging from cosmetics to paper coating. It is of fundamental interest because polysoaps are characterised by a rugged free energy landscape that is reminiscent of complex systems such as proteins and glasses. The talk concerns theoretical arguments regarding the following issues: (i) The design parameters that govern the spatial configurations of the polysoaps, (ii) The interaction between polysoaps and free amphiphiles, (iii) The effect of the intramolecular self organisation on the elasticity of the chains.

  20. The ALICE Configuration Tool

    Science.gov (United States)

    Boccioli, M.; Carena, F.; Chapeland, S.; Chibante Barroso, V.; Lechman, M.; Jusko, A.; Pinazza, O.; ALICE Collaboration

    2011-12-01

    ALICE (A Large Ion Collider Experiment) is the heavy-ion detector designed to study the physics of strongly interacting matter and the quark-gluon plasma at the CERN Large Hadron Collider (LHC). It includes 18 different sub-detectors and 5 online systems, each one made of many different components and developed by different teams inside the collaboration. The operation of a large experiment over several years to collect billions of events acquired in well defined conditions requires predictability and repeatability of the experiment configuration. The logistics of the operation is also a major issue and it is mandatory to reduce the size of the shift crew needed to operate the experiment. Appropriate software tools are therefore needed to automate daily operations. This ensures minimizing human errors and maximizing the data taking time. The ALICE Configuration Tool (ACT) is ALICE first step to achieve a high level of automation, implementing automatic configuration and calibration of the sub-detectors and online systems. This presentation describes the goals and architecture of the ACT, the web-based Human Interface and the commissioning performed before the start of the collisions. It also reports on the first experiences with real use in daily operations, and finally it presents the road-map for future developments.

  1. The private – public law divide

    DEFF Research Database (Denmark)

    Gyldenløve Jeppesen-de Boer, Christina; Kronborg, Annette; Svendsen, Idamarie Leth

    2013-01-01

    to a particular societal institution. Marriage as an institution has been individualized and the goodness of the family has to relate to the well-being of the individuals instead. This article shows that within this historical development the private-public law divide has not been seriously challenged......In a Scandinavian perspective, the family and the individual have changed places during the 20th Century. Today, the law takes its starting point in the individual - not in the family. A consequence of this development is that it is no longer legally possible to relate the good family...

  2. CMOS Direct-Injection Divide-by-3 Injection-Locked Frequency Dividers

    Institute of Scientific and Technical Information of China (English)

    Chia-Wei; Chang; Jhin-Fang; Huang; Sheng-Lyang; Jang; Ying-Hsiang; Liao; Miin-Horng; Juang

    2010-01-01

    <正>This paper proposes CMOS LC-tank divide-by-3 injection locked frequency dividers(ILFDs)fabricated in 0.18μn and 90nm CMOS process and describes the circuit design,operation principle and measurement results of the ILFDs.The ILFDs use two injection series-MOSFETs across the LC resonator and a differential injection signal is applied to the gates of injection MOSFETs.The direct-injection divide-by-3 ILFDs are potential for radio-frequency application and can have wide locking range.

  3. Apparatus for Controlling Low Power Voltages in Space Based Processing Systems

    Science.gov (United States)

    Petrick, David J. (Inventor)

    2017-01-01

    A low power voltage control circuit for use in space missions includes a switching device coupled between an input voltage and an output voltage. The switching device includes a control input coupled to an enable signal, wherein the control input is configured to selectively turn the output voltage on or off based at least in part on the enable signal. A current monitoring circuit is coupled to the output voltage and configured to produce a trip signal, wherein the trip signal is active when a load current flowing through the switching device is determined to exceed a predetermined threshold and is inactive otherwise. The power voltage control circuit is constructed of space qualified components.

  4. America's digital divide: 2000-2003 trends.

    Science.gov (United States)

    Whaley, Kermit C

    2004-04-01

    Computer ownership and literacy, along with Internet access and its many applications, has become, for many, a trademark for the Americans' lifestyle. Research shows that computer ownership and literacy, along with Internet access and expertise, is rapidly changing how Americans go about their business. The technological industry is providing many opportunities for Americans to operate in markets, global and local, not previously available. These changes are apparent across all U.S. sociocultural and geographic boundaries. Yet, upon close analysis, there are individuals and communities less connected with many completely excluded from participation. Those individuals exist below a line called the Digital Divide. Growth in computer ownership and Internet use, while offering optimism that the Digital Divide is narrowing, also illustrates that, without focused intervention will for certain populations, continue. Public and private programs, focus groups, and pocks of community activism, each hope to correct the disparities among on- and-off line Americans. On many fronts, there is evidence that progress is being made by many. Income, race, age, and geographic location are often the determining factors.

  5. Media Literacy in Times of Media Divides

    Directory of Open Access Journals (Sweden)

    Kaja Žuran

    2013-12-01

    Full Text Available We live in a post-modern society, an information society, a society based around knowledge and participation, and above all in a media society. In a media culture where media holds a dominant position, we cannot overlook the emerging idea of a ‘media divide’ within the frame of media education, media literate individuals and the expansion of the traditional concept of media literacy. Firstly, we are in an era of technological revolution, and it is time to consider the meaning and function of media and how we experience it in our everyday life. Secondly, as a society we are subject to intense media invasion and we all need to learn how to use it to our benefit and apply a critical and autonomous perspective towards selecting media content. Otherwise the media divide between the media literate and illiterate will widen; but is there even a chance to overcome the supposed divide between those who are formally media educated and those who are not?

  6. Deployment of low-voltage regulator considering existing voltage control in medium-voltage distribution systems

    Directory of Open Access Journals (Sweden)

    Hiroshi Kikusato

    2016-01-01

    Full Text Available Many photovoltaic (PV systems have been installed in distribution systems. This installation complicates the maintenance of all voltages within the appropriate range in all low-voltage distribution systems (LVDSs because the trends in voltage fluctuation differ in each LVDS. The installation of a low-voltage regulator (LVR that can accordingly control the voltage in each LVDS has been studied as a solution to this problem. Voltage control in a medium-voltage distribution system must be considered to study the deployment of LVRs. In this study, we installed LVRs in the LVDSs in which the existing voltage-control scheme cannot prevent voltage deviation and performed a numerical simulation by using a distribution system model with PV to evaluate the deployment of the LVRs.

  7. Systems and methods for process and user driven dynamic voltage and frequency scaling

    Science.gov (United States)

    Mallik, Arindam; Lin, Bin; Memik, Gokhan; Dinda, Peter; Dick, Robert

    2011-03-22

    Certain embodiments of the present invention provide a method for power management including determining at least one of an operating frequency and an operating voltage for a processor and configuring the processor based on the determined at least one of the operating frequency and the operating voltage. The operating frequency is determined based at least in part on direct user input. The operating voltage is determined based at least in part on an individual profile for processor.

  8. Universal logic gates via liquid-electronic hybrid divider

    KAUST Repository

    Zhou, Bingpu

    2012-01-01

    We demonstrated two-input microdroplet-based universal logic gates using a liquid-electronic hybrid divider. All 16 Boolean logic functions have been realized by manipulating the applied voltages. The novel platform consists of a microfluidic chip with integrated microdroplet detectors and external electronic components. The microdroplet detectors act as the communication media for fluidic and electronic information exchange. The presence or absence of microdroplets at the detector translates into the binary signal 1 or 0. The embedded micro-mechanical pneumatically actuated valve (PAV), fabricated using the well-developed multilayer soft lithography technique, offers biocompatibility, flexibility and accuracy for the on-chip realization of different logic functions. The microfluidic chip can be scaled up to construct large-scale microfluidic logic computation. On the other hand, the microfluidic chip with a specific logic function can be applied to droplet-based chemical reactions for on-demand bio or chemical analysis. Our experimental results have presented an autonomously driven, precision-controlled microfluidic chip for chemical reactions based on the IF logic function. © 2012 The Royal Society of Chemistry.

  9. Automatic Configuration in NTP

    Institute of Scientific and Technical Information of China (English)

    Jiang Zongli(蒋宗礼); Xu Binbin

    2003-01-01

    NTP is nowadays the most widely used distributed network time protocol, which aims at synchronizing the clocks of computers in a network and keeping the accuracy and validation of the time information which is transmitted in the network. Without automatic configuration mechanism, the stability and flexibility of the synchronization network built upon NTP protocol are not satisfying. P2P's resource discovery mechanism is used to look for time sources in a synchronization network, and according to the network environment and node's quality, the synchronization network is constructed dynamically.

  10. Increased voltage photovoltaic cell

    Science.gov (United States)

    Ross, B.; Bickler, D. B.; Gallagher, B. D. (Inventor)

    1985-01-01

    A photovoltaic cell, such as a solar cell, is provided which has a higher output voltage than prior cells. The improved cell includes a substrate of doped silicon, a first layer of silicon disposed on the substrate and having opposite doping, and a second layer of silicon carbide disposed on the first layer. The silicon carbide preferably has the same type of doping as the first layer.

  11. High Voltage Seismic Generator

    Science.gov (United States)

    Bogacz, Adrian; Pala, Damian; Knafel, Marcin

    2015-04-01

    This contribution describes the preliminary result of annual cooperation of three student research groups from AGH UST in Krakow, Poland. The aim of this cooperation was to develop and construct a high voltage seismic wave generator. Constructed device uses a high-energy electrical discharge to generate seismic wave in ground. This type of device can be applied in several different methods of seismic measurement, but because of its limited power it is mainly dedicated for engineering geophysics. The source operates on a basic physical principles. The energy is stored in capacitor bank, which is charged by two stage low to high voltage converter. Stored energy is then released in very short time through high voltage thyristor in spark gap. The whole appliance is powered from li-ion battery and controlled by ATmega microcontroller. It is possible to construct larger and more powerful device. In this contribution the structure of device with technical specifications is resented. As a part of the investigation the prototype was built and series of experiments conducted. System parameter was measured, on this basis specification of elements for the final device were chosen. First stage of the project was successful. It was possible to efficiently generate seismic waves with constructed device. Then the field test was conducted. Spark gap wasplaced in shallowborehole(0.5 m) filled with salt water. Geophones were placed on the ground in straight line. The comparison of signal registered with hammer source and sparker source was made. The results of the test measurements are presented and discussed. Analysis of the collected data shows that characteristic of generated seismic signal is very promising, thus confirms possibility of practical application of the new high voltage generator. The biggest advantage of presented device after signal characteristics is its size which is 0.5 x 0.25 x 0.2 m and weight approximately 7 kg. This features with small li-ion battery makes

  12. DIGITAL DIVIDE IN THE EUROPEAN UNION

    Directory of Open Access Journals (Sweden)

    Radu HERMAN

    2009-10-01

    Full Text Available This paper aims to demonstrate that income, education and infrastructure play a critical role in shaping the divide. The global challenge for the new millennium is to build a society where everyone can access and shareinformation. A fully integrated digital world has become a reality, and all segments of society must embrace it in order to be contributing partners to future success in the EU. As they are fast becoming an essential tool for economic activity, Information and Communication Technologies (ICT became a vital engine of economic performance. The problem, however, is that in many countries technological diffusion is obstructed by the limited capacity of networks to carry large amounts of knowledge swiftly and the limited access of individuals even to networks in which knowledge products are minimal.

  13. Library outreach: addressing Utah's "Digital Divide".

    Science.gov (United States)

    McCloskey, K M

    2000-10-01

    A "Digital Divide" in information and technological literacy exists in Utah between small hospitals and clinics in rural areas and the larger health care institutions in the major urban area of the state. The goals of the outreach program of the Spencer S. Eccles Health Sciences Library at the University of Utah address solutions to this disparity in partnership with the National Network of Libraries of Medicine-- Midcontinental Region, the Utah Department of Health, and the Utah Area Health Education Centers. In a circuit-rider approach, an outreach librarian offers classes and demonstrations throughout the state that teach information-access skills to health professionals. Provision of traditional library services to unaffiliated health professionals is integrated into the library's daily workload as a component of the outreach program. The paper describes the history, methodology, administration, funding, impact, and results of the program.

  14. A new level-shifting structure with multiply metal rings by divided RESURF technique

    Institute of Scientific and Technical Information of China (English)

    Liu Jizhi; Chen Xingbi

    2009-01-01

    A new structure of a lateral n-MOST and a new level-shifting structure with multiply metal rings(MMRs) by divided RESURF technique have been proposed.The device and electrical performances of the structure are analyzed and simulated by MEDICI.In comparison to the level-shifting structure with multiply floating field plates (MFFPs)used before,the structure stated here improves the reliability and diminishes the voltage difference between the voltage of the power supply of the high-side gate driver and the voltage of the output terminal of the level-shifting structure,which is also that of the input terminal of the high-side gate driver.The maximal voltage difference of the level-shifting structure in this paper is 30%lower than that used before.Therefore,good voltage isolation and current isolation are obtained.The structure can be used in the level-shifting circuit of various applications.

  15. Treatment of emulsified oils by electrocoagulation: pulsed voltage applications.

    Science.gov (United States)

    Genc, Ayten; Bakirci, Busra

    2015-01-01

    The effect of pulsed voltage application on energy consumption during electrocoagulation was investigated. Three voltage profiles having the same arithmetic average with respect to time were applied to the electrodes. The specific energy consumption for these profiles were evaluated and analyzed together with oil removal efficiencies. The effects of applied voltages, electrode materials, electrode configurations, and pH on oil removal efficiency were determined. Electrocoagulation experiments were performed by using synthetic and real wastewater samples. The pulsed voltages saved energy during the electrocoagulation process. In continuous operation, energy saving was as high as 48%. Aluminum electrodes used for the treatment of emulsified oils resulted in higher oil removal efficiencies in comparison with stainless steel and iron electrodes. When the electrodes gap was less than 1 cm, higher oil removal efficiencies were obtained. The highest oil removal efficiencies were 95% and 35% for the batch and continuous operating modes, respectively.

  16. SIM Configuration Evolution

    Science.gov (United States)

    Aaron, Kim M.

    2000-01-01

    The Space Interferometry Mission (SIM) is a space-based 10 m baseline Michelson interferometer. Planned for launch in 2005 aboard a Delta III launch vehicle, or equivalent, its primary objective is to measure the positions of stars and other celestial objects with an unprecedented accuracy of 4 micro arc seconds. With such an instrument, tremendous advancement can be expected in our understanding of stellar and galactic dynamics. Using triangulation from opposite sides of the orbit around the sun (i.e. by using parallax) one can measure the distance to any observable object in our galaxy. By directly measuring the orbital wobble of nearby stars, the mass and orbit of planets can be determined over a wide range of parameters. The distribution of velocity within nearby galaxies will be measurable. Observations of these and other objects will improve the calibration of distance estimators by more than an order of magnitude. This will permit a much better determination of the Hubble Constant as well as improving our overall understanding of the evolution of the universe. SIM has undergone several transformations, especially over the past year and a half since the start of Phase A. During this phase of a project, it is desirable to perform system-level trade studies, so the substantial evolution of the design that has occurred is quite appropriate. Part of the trade-off process has addressed two major underlying architectures: SIM Classic; and Son of SIM. The difference between these two architectures is related to the overall arrangement of the optical elements and the associated metrology system. Several different configurations have been developed for each architecture. Each configuration is the result of design choices that are influenced by many competing considerations. Some of the more important aspects will be discussed. The Space Interferometry Mission has some extremely challenging goals: millikelvin thermal stability, nanometer stabilization of optics

  17. Mitigation of Voltage Sags in CIGRE Low Voltage Distribution Network

    DEFF Research Database (Denmark)

    Mustafa, Ghullam; Bak-Jensen, Birgitte; Mahat, Pukar;

    2013-01-01

    problems in the distribution system. The voltage problems dealt with in this paper are to show how to mitigate voltage sags in the CIGRE Low Voltage (LV) test network and networks like this. The voltage sags, for the tested cases in the CIGRE LV test network are mainly due to three phase faults....... The compensation of voltage sags in the different parts of CIGRE distribution network is done by using the four STATCOM compensators already existing in the test grid. The simulations are carried out in DIgSILENT power factory software version 15.0....

  18. Voltage Controlled Dynamic Demand Response

    DEFF Research Database (Denmark)

    Bhattarai, Bishnu Prasad; Bak-Jensen, Birgitte; Mahat, Pukar

    2013-01-01

    . An adaptive dynamic model has been developed to determine composite voltage dependency of an aggregated load on feeder level. Following the demand dispatch or control signal, optimum voltage setting at the LV substation is determined based on the voltage dependency of the load. Furthermore, a new technique...

  19. Charge-pump voltage converter

    Science.gov (United States)

    Brainard, John P.; Christenson, Todd R.

    2009-11-03

    A charge-pump voltage converter for converting a low voltage provided by a low-voltage source to a higher voltage. Charge is inductively generated on a transfer rotor electrode during its transit past an inductor stator electrode and subsequently transferred by the rotating rotor to a collector stator electrode for storage or use. Repetition of the charge transfer process leads to a build-up of voltage on a charge-receiving device. Connection of multiple charge-pump voltage converters in series can generate higher voltages, and connection of multiple charge-pump voltage converters in parallel can generate higher currents. Microelectromechanical (MEMS) embodiments of this invention provide a small and compact high-voltage (several hundred V) voltage source starting with a few-V initial voltage source. The microscale size of many embodiments of this invention make it ideally suited for MEMS- and other micro-applications where integration of the voltage or charge source in a small package is highly desirable.

  20. An improved fully integrated, high-speed, dual-modulus divider

    Science.gov (United States)

    Zheng, Sun; Yong, Xu; Guangyan, Ma; Hui, Shi; Fei, Zhao; Ying, Lin

    2014-11-01

    A fully integrated 2n/2n+1 dual-modulus divider in GHz frequency range is presented. The improved structure can make all separated logic gates embed into correlative D flip—flops completely. In this way, the complex logic functions can be performed with a minimum number of devices and with maximum speed, so that lower power consumption and faster speed are obtained. In addition, the low-voltage bandgap reference needed by the frequency divider is specifically designed to provide a 1.0 V output. According to the design demand, the circuit is fabricated in 0.18 μm standard CMOS process, and the measured results show that its operating frequency range is 1.1-2.5 GHz. The dual-modulus divider dissipates 1.1 mA from a 1.8 V power supply. The temperature coefficient of the reference voltage circuit is 8.3 ppm/°C when the temperature varies from -40 to +125 °C. By comparison, the dual-modulus divide designed in this paper can possess better performance and flexibility.

  1. An improved fully integrated, high-speed, dual-modulus divider

    Institute of Scientific and Technical Information of China (English)

    Sun Zheng; Xu Yong; Ma Guangyan; Shi Hui; Zhao Fei; Lin Ying

    2014-01-01

    A fully integrated 2n/2n+l dual-modulus divider in GHz frequency range is presented.The improved structure can make all separated logic gates embed into correlative D flip-flops completely.In this way,the complex logic functions can be performed with a minimum number of devices and with maximum speed,so that lower power consumption and faster speed are obtained.In addition,the low-voltage bandgap reference needed by the frequency divider is specifically designed to provide a 1.0 V output.According to the design demand,the circuit is fabricated in 0.18μm standard CMOS process,and the measured results show that its operating frequency range is 1.1-2.5 GHz.The dual-modulus divider dissipates 1.1 mA from a 1.8 V power supply.The temperature coefficient of the reference voltage circuit is 8.3 ppm/℃ when the temperature varies from-40 to + 125 ℃.By comparison,the dual-modulus divide designed in this paper can possess better performance and flexibility.

  2. Transient voltage sharing in series-coupled high voltage switches

    Directory of Open Access Journals (Sweden)

    Editorial Office

    1992-07-01

    Full Text Available For switching voltages in excess of the maximum blocking voltage of a switching element (for example, thyristor, MOSFET or bipolar transistor such elements are often coupled in series - and additional circuitry has to be provided to ensure equal voltage sharing. Between each such series element and system ground there is a certain parasitic capacitance that may draw a significant current during high-speed voltage transients. The "open" switch is modelled as a ladder network. Analy­sis reveals an exponential progression in the distribution of the applied voltage across the elements. Overstressing thus oc­curs in some of the elements at levels of the total voltage that are significantly below the design value. This difficulty is overcome by grading the voltage sharing circuitry, coupled in parallel with each element, in a prescribed manner, as set out here.

  3. Voltage-Mode Highpass, Bandpass, Lowpass and Notch Biquadratic Filters Using Single DDCC

    Directory of Open Access Journals (Sweden)

    W. Y. Chiu

    2012-04-01

    Full Text Available A new voltage-mode multifunction biquadratic filter using one differential difference current conveyor (DDCC, two grounded capacitors and three resistors is presented. The proposed circuit offers the following attractive advantages: realizing highpass, bandpass, lowpass and notch filter functions, simultaneously, from the same circuit configuration; employing grounded capacitors, which is ideal for integration and simpler circuit configuration.

  4. Design Comparison of Autonomous High Voltage Driving System for DEAP Actuator

    DEFF Research Database (Denmark)

    Huang, Lina; Pittini, Riccardo; Zhang, Zhe

    2014-01-01

    As a new type of smart material, the Dielectric Electro Active Polymer (DEAP) is introduced in terms of configuration, working principle and potential applications. The design of an autonomous high voltage driving system for DEAP actuator is investigated. The system configuration and the design...

  5. TWRS Configuration management program plan

    Energy Technology Data Exchange (ETDEWEB)

    Vann, J.M.

    1996-06-03

    The TWRS Configuration Management Program Plan (CMPP) integrates technical and administrative controls to establish and maintain consistency among requirements, product configuration, and product information for TWRS products during all life cycle phases. This CMPP will be used by TWRS management and configuration management personnel to establish and manage the technical and integrated baselines and controls and status changes to those baselines.

  6. Counterintuitive Behaviors in Configuration Mixing

    CERN Document Server

    Yu, Xiaofei; Robinson, Shadow

    2016-01-01

    By starting with a simple configurations of 2 neutrons in a single j shell we hare able to learn the effects of high lying configurations on physical properties such as nuclear magnetic g factors. Some counterintuitive results are found when both high lying spin orbit partners are allowed to admix with the basic configuration.

  7. High-Voltage, Low-Power BNC Feedthrough Terminator

    Science.gov (United States)

    Bearden, Douglas

    2012-01-01

    This innovation is a high-voltage, lowpower BNC (Bayonet Neill-Concelman) feedthrough that enables the user to terminate an instrumentation cable properly while connected to a high voltage, without the use of a voltage divider. This feedthrough is low power, which will not load the source, and will properly terminate the instrumentation cable to the instrumentation, even if the cable impedance is not constant. The Space Shuttle Program had a requirement to measure voltage transients on the orbiter bus through the Ground Lightning Measurement System (GLMS). This measurement has a bandwidth requirement of 1 MHz. The GLMS voltage measurement is connected to the orbiter through a DC panel. The DC panel is connected to the bus through a nonuniform cable that is approximately 75 ft (approximately equal to 23 m) long. A 15-ft (approximately equal to 5-m), 50-ohm triaxial cable is connected between the DC panel and the digitizer. Based on calculations and simulations, cable resonances and reflections due to mismatched impedances of the cable connecting the orbiter bus and the digitizer causes the output not to reflect accurately what is on the bus. A voltage divider at the DC panel, and terminating the 50-ohm cable properly, would eliminate this issue. Due to implementation issues, an alternative design was needed to terminate the cable properly without the use of a voltage divider. Analysis shows how the cable resonances and reflections due to the mismatched impedances of the cable connecting the orbiter bus and the digitizer causes the output not to reflect accurately what is on the bus. After simulating a dampening circuit located at the digitizer, simulations were performed to show how the cable resonances were dampened and the accuracy was improved significantly. Test cables built to verify simulations were accurate. Since the dampening circuit is low power, it can be packaged in a BNC feedthrough.

  8. Electrically configurable materials and devices for intelligent neuromorphic applications

    Science.gov (United States)

    Lai, Qianxi

    As miniaturization of advanced CMOS device is approaching its fundamental physical limit, emerging electrically configurable devices which can modify its function dynamically and adaptively can arm existing CMOS circuitry with more versatile function, and are essential for reconfigurable computing and intelligent neural circuit. Organic semiconductors have the flexibility to change its electrical properties by changing its dopant concentration. Controllable ionic doping in conductive polymers has been realized and utilized to make electrically configurable devices for intelligent neuromorphic applications. First, a nonvolatile organic memory made of dopant configurable polymers has been demonstrated and showed controllable and repeatable conductance switching and nonvolatile characteristics. A 16x16 crossbar network composed of configurable switching devices has been fabricated and has successfully demonstrated its application on associative memory which can memorize and recognize learned pattern even with extra or missing features. An organic/Si hybrid field configurable transistor (FCT) has been fabricated on a Si nanowire FET platform by integrating the dopant configurable polymer into the gate structure. The FCT can be precisely configured to desired nonvolatile analog state dynamically, repeatedly, and reversibly by controlling the concentration of ions dopants in the polymer with a gate voltage. The flexible configurability and plasticity of the FCT could facilitate field-programmable circuits for defect-tolerance and synapse-like devices for dynamic learning. Further investigation on this ion-doped polymer showed the voltage modulation of the ionic charge concentration and dipole moment concentration in the polymer which contributed to a new electric device-a memory capacitor. This ionic transport in the polymer can lead to the time-dependent electrical property of the FCT (a synaptic transistor), which has demonstrated the first time synapse-like spiking

  9. Configuring the autism epidemic

    DEFF Research Database (Denmark)

    Christensen, Fie Lund Lindegaard; Seeberg, Jens

    2017-01-01

    Autism has been described as an epidemic, but this claim is contested and may point to an awareness epidemic, i.e. changes in the definition of what autism is and more attention being invested in diagnosis leading to a rise in registered cases. The sex ratio of children diagnosed with autism...... is skewed in favour of boys, and girls with autism tend to be diagnosed much later than boys. Building and further developing the notion of ‘configuration’ of epidemics, this article explores the configuration of autism in Denmark, with a particular focus on the health system and social support to families...... with children diagnosed with autism, seen from a parental perspective. The article points to diagnostic dynamics that contribute to explaining why girls with autism are not diagnosed as easily as boys. We unfold these dynamics through the analysis of a case of a Danish family with autism....

  10. Bridging the divide between science and journalism.

    Science.gov (United States)

    Van Eperen, Laura; Marincola, Francesco M; Strohm, Jennifer

    2010-03-10

    There are countless reasons nearly every scientist should learn how to communicate effectively with the media, including increased understanding of critical research findings to attract or sustain funding and build new professional partnerships that will further propel forward research. But where do scientists begin? Bridging the Divide between Science and Journalism offers practical tips for any scientist looking to work with the media.Given the traditional and internet-based sources for medical research and healthcare-related news now available, it is imperative that scientists know how to communicate their latest findings through the appropriate channels. The credible media channels are managed by working journalists, so learning how to package vast, technical research in a form that is appetizing and "bite-sized" in order to get their attention, is an art. Reducing years of research into a headline can be extremely difficult and certainly doesn't come naturally to every scientist, so this article provides suggestions on how to work with the media to communicate your findings.

  11. New Frontiers in the Digital Divide

    DEFF Research Database (Denmark)

    Jæger, Birgit

    In a new strategy for e-government, the Danish government set the goal that in 2015 all contacts between citizens and public authorities must be conducted electronically. In accordance with EU’s strategy for e-government every citizen ought to have equal access to public services, hence the quest......In a new strategy for e-government, the Danish government set the goal that in 2015 all contacts between citizens and public authorities must be conducted electronically. In accordance with EU’s strategy for e-government every citizen ought to have equal access to public services, hence...... for digital inclusion becomes a central theme for the implementation of the new e-government strategy. Until now it has been voluntary whether or not citizens want to use ICT and a lot of especially senior citizens have chosen not to use the technology. However, senior citizens are not the only group affected...... of the e-government strategy. New frontiers in the digital divide are opening and a new group of excluded become visible: the youngsters. In this way, one of the leading Danish newspapers reports that young people lines up in town halls to get help to fill out forms, which are already available...

  12. The Digital Divide and urban older adults.

    Science.gov (United States)

    Cresci, M Kay; Yarandi, Hossein N; Morrell, Roger W

    2010-01-01

    Computers and the Internet offer older adults opportunities and resources for independent living. However, many urban older adults do not use computers. This study examined the demographic, health, and social activities of urban older adults to determine variables that might predict the use and nonuse of computers in this population. A secondary data analysis was performed using the 2001 Detroit City-Wide Needs Assessment of Older Adults (n = 1410) data set. Logistic regression was used to explore potential differences in predictor variables between computer users and nonusers. Overall, computer users were younger (27%), had a higher level of education, were more likely to be employed, had an annual income greater than $20,000, and were healthier and more active than nonusers. They also were more likely to have memberships in community organizations and do volunteer work. Preferred computer activities included conducting Internet searches, playing games, writing, and communicating with family members and friends. The results suggest significant differences in demographic and health-related characteristics between computer users and nonusers among urban older adults. Although about a quarter of participants in this study used computers, the Digital Divide continues to exist in urban settings for scores of others.

  13. Bridging the digital divide: reaching vulnerable populations.

    Science.gov (United States)

    Chang, Betty L; Bakken, Suzanne; Brown, S Scott; Houston, Thomas K; Kreps, Gary L; Kukafka, Rita; Safran, Charles; Stavri, P Zoe

    2004-01-01

    The AMIA 2003 Spring Congress entitled "Bridging the Digital Divide: Informatics and Vulnerable Populations" convened 178 experts including medical informaticians, health care professionals, government leaders, policy makers, researchers, health care industry leaders, consumer advocates, and others specializing in health care provision to underserved populations. The primary objective of this working congress was to develop a framework for a national agenda in information and communication technology to enhance the health and health care of underserved populations. Discussions during four tracks addressed issues and trends in information and communication technologies for underserved populations, strategies learned from successful programs, evaluation methodologies for measuring the impact of informatics, and dissemination of information for replication of successful programs. Each track addressed current status, ideal state, barriers, strategies, and recommendations. Recommendations of the breakout sessions were summarized under the overarching themes of Policy, Funding, Research, and Education and Training. The general recommendations emphasized four key themes: revision in payment and reimbursement policies, integration of health care standards, partnerships as the key to success, and broad dissemination of findings including specific feedback to target populations and other key stakeholders.

  14. The Gender Digital Divide in Developing Countries

    Directory of Open Access Journals (Sweden)

    Amy Antonio

    2014-10-01

    Full Text Available Empirical studies clearly show that women in the developing world have significantly lower technology participation rates than men; a result of entrenched socio-cultural attitudes about the role of women in society. However, as studies are beginning to show, when those women are able to engage with Internet technology, a wide range of personal, family and community benefits become possible. The key to these benefits is on-line education, the access to which sets up a positive feedback loop. This review gives an overview of the digital divide, before focusing specifically on the challenges women in developing countries face in accessing the Internet. Current gender disparities in Internet use will be outlined and the barriers that potentially hinder women’s access and participation in the online world will be considered. We will then look at the potential opportunities for women’s participation in a global digital society along with a consideration of current initiatives that have been developed to mitigate gender inequity in developing countries. We will also consider a promising avenue for future research.

  15. Quantitative Measurement of the Digital Divide

    Science.gov (United States)

    Cottrell, Roger

    2007-04-01

    Bandwidth and the Internet infrastructure are the life-blood of the world's knowledge economy, but they are often scarcest where most needed. Measuring the numbers of users of the Internet infrastructure is not easy in developing countries because many people share accounts, use corporate and academic networks, or visit the rapidly growing number of cyber cafes, telecentres and business services. Also measuring the number of users does not take into account the level of use. One valuable indicator for measuring the Internet infrastructure is the international Internet performance of a country or region. One of the major aims of the PingER project is to provide an historical archive of extensive, publicly accessible, up-to-date, measurements, analyses and reports of multiple Internet performance indicators (such as delay, loss, throughput, reachability, and jitter) between sites, countries and regions of the world. This talk will briefly describe the PingER project and then compare and contrast the Internet performance and its trends within and between countries and regions of the world. By means of extensive case studies it will also identify which regions need the greatest attention, together with their major issues and possible approaches to reducing the divide.

  16. Vegetation baseline report : Connacher great divide project

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2005-08-01

    This baseline report supported an application by Connacher Oil and Gas Ltd. to the Alberta Energy and Utilities Board (EUB) and Alberta Environment (AENV) for the Great Divide Steam Assisted Gravity Drainage (SAGD) Project. The goal of the report was to document the distribution and occurrence of ecosite phases and wetland classes in the project footprint as well as to document the distribution of rare plants; rare plant communities: and intrusive species and old growth communities, including species of management concern. A methodology of the baseline report was presented, including details of mapping and field surveys. Six vegetation types in addition to the disturbed land unit were identified in the project footprint and associated buffer. It was noted that all vegetation types are common for the boreal forest natural regions. Several species of management concern were identified during the spring rare plant survey, including rare bryophytes and non-native or invasive species. Mitigation was identified through a slight shift of the footprint, transplant of appropriate bryophyte species and implementation of a weed management plan. It was noted that results of future surveys for rare plants will be submitted upon completion. It was concluded that the effects of the project on existing vegetation is expected to be low because of the small footprint, prior disturbance history, available mitigation measures and conservation and reclamation planning. 27 refs., 5 tabs., 4 figs.

  17. Bridging the Divide between Science and Journalism

    Directory of Open Access Journals (Sweden)

    Marincola Francesco M

    2010-03-01

    Full Text Available Abstract There are countless reasons nearly every scientist should learn how to communicate effectively with the media, including increased understanding of critical research findings to attract or sustain funding and build new professional partnerships that will further propel forward research. But where do scientists begin? Bridging the Divide between Science and Journalism offers practical tips for any scientist looking to work with the media. Given the traditional and internet-based sources for medical research and healthcare-related news now available, it is imperative that scientists know how to communicate their latest findings through the appropriate channels. The credible media channels are managed by working journalists, so learning how to package vast, technical research in a form that is appetizing and "bite-sized" in order to get their attention, is an art. Reducing years of research into a headline can be extremely difficult and certainly doesn't come naturally to every scientist, so this article provides suggestions on how to work with the media to communicate your findings.

  18. Novel Low Loss Active Voltage Clamp Circuit for Series Connection of RCGCT thyristors

    Science.gov (United States)

    Ito, Hiroshi; Suzuki, Akihiro; Iwata, Akihiko

    This paper describes novel low loss active voltage clamp circuits for the series connection of RCGCT thyristors. For high voltage converters the series connection of power semiconductor devices is an essential technique for direct switching of high voltages. Several protection circuits have been applied to the series connection of RCGCT thyristors such as CRD snubber circuits which suppress over-voltages across RCGCT thyristors, and voltage balancing resistors to equalize voltage sharing in steady states. However, significant losses in these protection circuits lower the converter’s efficiency. We propose novel low-loss protection circuits, which have active voltage clamp snubber circuits and static voltage balancing circuits. The clamp capacitor voltage of the active voltage clamp snubber circuits are designed to be higher than the equally divided DC-Link voltage. This method can reduce the loss of the clamp circuit to no more than 1/10 of that of the conventional CRD snubber. Also the static voltage balancing circuits compensate for the voltage imbalance generated by the difference in the leakage current between the series connection RCGCT thyristors.

  19. No-Voltage Meter

    Science.gov (United States)

    1976-02-01

    VW- IKft, 1/4 H4 -Wv- IK!1, I/4W INTERNAL VOLTAGE NOTE ALL TRANSISTORS ARE 2N43A OR EQUIVALENT GERMANIUM ALLOY PNP AA ALKALINE BATTERY...D-,, regardless of polarity. This signal is then full-wave rectified by the diode-connected Germanium transistor bridge, T,, T-,, T3, and T4... Transistor T5 acts as a second current limiter. Resistor R2 was selected to give 90 f# of full-scale meter deflection with an input signal of 115 volts

  20. Benchmarking of Voltage Sag Generators

    DEFF Research Database (Denmark)

    Yang, Yongheng; Blaabjerg, Frede; Zou, Zhixiang

    2012-01-01

    The increased penetration of renewable energy systems, like photovoltaic and wind power systems, rises the concern about the power quality and stability of the utility grid. Some regulations for Low Voltage Ride-Through (LVRT) for medium voltage or high voltage applications, are coming into force...... to guide these grid-connected distributed power generation systems. In order to verify the response of such systems for voltage disturbance, mainly for evaluation of voltage sags/dips, a Voltage Sag Generator (VSG) is needed. This paper evaluates such sag test devices according to IEC 61000 in order...... to provide cheaper solutions to test against voltage sags. Simulation and experimental results demonstrate that the shunt impedance based VSG solution is the easiest and cheapest one for laboratory test applications. The back-to-back fully controlled converter based VSG is the most flexible solution...

  1. Analysis and Improvement of Reflection-type Transverse Modulation Optical Voltage Sensors

    Institute of Scientific and Technical Information of China (English)

    LUO Sunan; YE Miaoyuan; XU Yan; CUI Ying

    2001-01-01

    Reflection-type transverse modulation optical voltage sensors, which employ reflection retarders to replace quarter-wave plates, are convenient for practical use. In previous literatures, the measured voltage was all applied to Bi4Ge3O12 crystal along the (110) direction for transverse modulation optical voltage sensor, and crystals are used as sensing materials. In this paper, reflection-type transverse modulation optical voltage sensor has been analyzed theoretically and a novel configuration in which the measured voltage is applied to a Bi4C-e3O12 crystal along the (001) direction with light wave passing through the crystal in the (110) direction has been proposed. According to this theoretical analysis, a novel optical voltage sensor, which can be used in a 220 kV optical fiber voltage transformer, has been designed and assembled. Experimental results showed that the linearity and the stability of the sensor during 24 hours can reach 0.3%.

  2. Research and Experiments on a Unipolar Capacitive Voltage Sensor

    Directory of Open Access Journals (Sweden)

    Qiang Zhou

    2015-08-01

    Full Text Available Voltage sensors are an important part of the electric system. In service, traditional voltage sensors need to directly contact a high-voltage charged body. Sensors involve a large volume, complex insulation structures, and high design costs. Typically an iron core structure is adopted. As a result, ferromagnetic resonance can occur easily during practical application. Moreover, owing to the multilevel capacitor divider, the sensor cannot reflect the changes of measured voltage in time. Based on the electric field coupling principle, this paper designs a new voltage sensor; the unipolar structure design solves many problems of traditional voltage sensors like the great insulation design difficulty and high costs caused by grounding electrodes. A differential signal input structure is adopted for the detection circuit, which effectively restrains the influence of the common-mode interference signal. Through sensor modeling, simulation and calculations, the structural design of the sensor electrode was optimized, miniaturization of the sensor was realized, the voltage division ratio of the sensor was enhanced, and the phase difference of sensor measurement was weakened. The voltage sensor is applied to a single-phase voltage class line of 10 kV for testing. According to the test results, the designed sensor is able to meet the requirements of accurate and real-time measurement for voltage of the charged conductor as well as to provide a new method for electricity larceny prevention and on-line monitoring of the power grid in an electric system. Therefore, it can satisfy the development demands of the smart power grid.

  3. Voltage source inverters for high power, variable-voltage DC power sources

    Energy Technology Data Exchange (ETDEWEB)

    Chen, Z. [Department of Engineering and Technology, De Montfort University, Queens Building, The Gateway, Leicester, LE1 9BH, (United Kingdom); Spooner, E. [School of Engineering, University of Durham, Science Laboratories, South Rd, Durham, DRI 3LE, (United Kingdom)

    2001-09-01

    The paper discusses the applications of voltage source inverter (VSI) based power electronic systems for interfacing variable-voltage DC sources to the grid. A variable-speed wind power conversion system is used for illustration, where the VSI-based interface needs to convert a variable DC voltage to a nearly constant AC voltage with high-quality power. The power control principles of VSI are described. Various system configurations and switching strategies are examined by analysis, simulation and experimental methods. It is shown that better utilisation of semiconductors and more flexible control may be achieved by using a separately controlled DC link, rather than a directly connected VSI that has to operate at a lower modulation ratio at higher power. In some cases, multipulse inverter structures may be preferred, despite higher component count, because of reduced switching losses, fault tolerance and the absence of filters. The solutions developed in the study could be applied at a different scale to other renewable energy sources, such as wave or solar photovoltaic devices. (Author)

  4. Application of Configurators in Networks

    DEFF Research Database (Denmark)

    Malis, Martin; Hvam, Lars

    2003-01-01

    Shorter lead-time, improved quality of product specifications and better communication with customers and suppliers are benefits derived from the application of configurators. Configurators are knowledge-based IT-systems that can be applied to deal with product knowledge and to support different...... processes in a company. Traditionally, configurators have been used as an internal tool. In this paper focus will be on the application of configurators in a network of companies, and a procedure for developing product configurators in a network of companies will be presented. The aim is to present...... a structured guideline, tools and methods on how to successfully develop configurators in a network perspective. Findings presented in this paper are supported by research in a case company. The results from the empirical work show a huge potential for the application of configurators in networks of companies....

  5. Voltage-Gated Channels as Causative Agents for Epilepsies

    Directory of Open Access Journals (Sweden)

    Mutasem Abuhamed

    2008-01-01

    Full Text Available Problem statement: Epilepsy is a common neurological disorder that afflicts 1-2% of the general population worldwide. It encompasses a variety of disorders with seizures. Approach: Idiopathic epilepsies were defined as a heterogeneous group of seizure disorders that show no underlying cause .Voltage-gated ion channels defect were recognized etiology of epilepsy in the central nervous system. The aim of this article was to provide an update on voltage-gated channels and their mutation as causative agents for epilepsies. We described the structures of the voltage-gated channels, discuss their current genetic studies, and then review the effects of voltage-gated channels as causative agents for epilepsies. Results: Channels control the flow of ions in and out of the cell causing depolarization and hyper polarization of the cell. Voltage-gated channels were classified into four types: Sodium, potassium calcium ands chloride. Voltage-gated channels were macromolecular protein complexes within the lipid membrane. They were divided into subunits. Each subunit had a specific function and was encoded by more than one gen. Conclusion: Current genetic studies of idiopathic epilepsies show the importance of genetic influence on Voltage-gated channels. Different genes may regulate a function in a channel; the channel defect was directly responsible for neuronal hyper excitability and seizures.

  6. Coordinated Voltage Control of Distributed PV Inverters for Voltage Regulation in Low Voltage Distribution Networks

    DEFF Research Database (Denmark)

    Nainar, Karthikeyan; Pokhrel, Basanta Raj; Pillai, Jayakrishnan Radhakrishna

    2017-01-01

    This paper reviews and analyzes the existing voltage control methods of distributed solar PV inverters to improve the voltage regulation and thereby the hosting capacity of a low-voltage distribution network. A novel coordinated voltage control method is proposed based on voltage sensitivity...... analysis, which is simple for computation and requires moderate automation and communication infrastructure. The proposed method is suitable for a hierarchical control structure where a supervisory controller has the provision to adapt the settings of local PV inverter controllers for overall system...

  7. Heat-pump performance: voltage dip/sag, under-voltage and over-voltage

    Directory of Open Access Journals (Sweden)

    William J.B. Heffernan

    2014-12-01

    Full Text Available Reverse cycle air-source heat-pumps are an increasingly significant load in New Zealand and in many other countries. This has raised concern over the impact wide-spread use of heat-pumps may have on the grid. The characteristics of the loads connected to the power system are changing because of heat-pumps. Their performance during under-voltage events such as voltage dips has the potential to compound the event and possibly cause voltage collapse. In this study, results from testing six heat-pumps are presented to assess their performance at various voltages and hence their impact on voltage stability.

  8. "Enlivening and - Dividing": An Aporia of Illumination

    Directory of Open Access Journals (Sweden)

    Hans Christian Hönes

    2015-08-01

    Full Text Available Normal 0 false false false EN-US JA X-NONE /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:10.0pt; font-family:Verdana;} In 1798, Karl August Böttiger paid a nocturnal visit to the Gallery of Antiques in Dresden, illuminating the statues with a torch. At first glance, this seems to be yet another example of a popular practice for visiting galleries c.1800. Illuminating the sculptures by torchlight was a popular means of enlivening the objects, set in motion by the light flickering on their surfaces. The collections were thus meant to become a place where cold, white stone comes to life, and where the beholder becomes part of a revived antiquity.This was precisely what Böttiger intended, too. But to him, the effect of the torchlight appeared to be, as he wrote, “enlivening and – dividing!” The torchlight highlighted not only the beauty of the sculptures but also their modern restorations. Böttiger apparently failed to experience the living presence of the antique celebrated by many of his contemporaries (e.g. Goethe, Moritz.This essay focuses on the consequence of such a perception of sculptures as historically multi-layered objects. Böttiger’s experience resulted in a problematic situation. In trying to view the sculptures as contemporaries, he hoped to become ancient himself. But this operation failed in the moment when the sculptures themselves appeared to be anachronistic, impure palimpsests. In consequence, galleries may not only be the place were art history as chronological Stilgeschichte was born. They may also be the site where this perception changed into the experience of a more chaotic shape of time.

  9. Isomerically Pure Tetramethylrhodamine Voltage Reporters.

    Science.gov (United States)

    Deal, Parker E; Kulkarni, Rishikesh U; Al-Abdullatif, Sarah H; Miller, Evan W

    2016-07-27

    We present the design, synthesis, and application of a new family of fluorescent voltage indicators based on isomerically pure tetramethylrhodamines. These new Rhodamine Voltage Reporters, or RhoVRs, use photoinduced electron transfer (PeT) as a trigger for voltage sensing, display excitation and emission profiles in the green to orange region of the visible spectrum, demonstrate high sensitivity to membrane potential changes (up to 47% ΔF/F per 100 mV), and employ a tertiary amide derived from sarcosine, which aids in membrane localization and simultaneously simplifies the synthetic route to the voltage sensors. The most sensitive of the RhoVR dyes, RhoVR 1, features a methoxy-substituted diethylaniline donor and phenylenevinylene molecular wire at the 5'-position of the rhodamine aryl ring, exhibits the highest voltage sensitivity to date for red-shifted PeT-based voltage sensors, and is compatible with simultaneous imaging alongside green fluorescent protein-based indicators. The discoveries that sarcosine-based tertiary amides in the context of molecular-wire voltage indicators prevent dye internalization and 5'-substituted voltage indicators exhibit improved voltage sensitivity should be broadly applicable to other types of PeT-based voltage-sensitive fluorophores.

  10. A Survey on Voltage Boosting Techniques for Step-Up DC-DC Converters

    DEFF Research Database (Denmark)

    Forouzesh, Mojtaba; Siwakoti, Yam Prasad; Gorji, Saman Asghari;

    2016-01-01

    , researches on new voltage boosting techniques are inevitable for various power converter applications. This can be achieved either by additional magnetic or by electric field storage elements with switching elements (switch and/or diode) in different configurations. Such combination of primary voltage...... boosting techniques and topologies are large, which at times may be confusing and difficult to follow/adapt for different applications. Considering these aspects and in order to make a clear sketch of the general law and framework of various voltage boosting techniques, this paper comprehensively reviews...... different voltage boosting techniques and categorizes them according to their circuit performance....

  11. Two-phase refrigerant distribution in a combining/dividing header of a brazed aluminum evaporator

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Nae Hyun; Byun, Ho Won; Go, Min Geon [School of Mechanical System Engineering, Incheon National University, Incheon (Korea, Republic of)

    2016-12-15

    For a brazed aluminum evaporator, it is very important to distribute the refrigerant (especially the liquid) evenly into each channel. If not, the liquid-deficient channel will be soon dry, and reduce the thermal performance of the evaporator. In this study, tests were conducted for a two pass evaporator having 10 combing channels and 14 dividing channels. Both lower and upper header configurations were considered. Effects of mass flux or vapor quality on flow distribution in the combining/dividing header were investigated. Data are also compared with those obtained from the header having 12 dividing channels. In the lower combining/dividing header, the effect of dividing header length on liquid distribution is different based on vapor quality. The centrifugal force, whose strength depends on header length and vapor quality, appears to play a significant role on flow distribution. In the upper combining/dividing header, the flow distribution is better for the header having shorter header length. The reason was attributed to more uniform height of the liquid pool, which is formed by the drained liquid film from top of the header. The effects of mass flux or vapor quality on flow distribution are also discussed.

  12. Backside configured surface plasmonic enhancement

    Energy Technology Data Exchange (ETDEWEB)

    Gu, Guiru; Lu, Xuejun, E-mail: xuejun-lu@uml.edu [Department of Electrical and Computer Engineering, University of Massachusetts Lowell, One University Avenue, Lowell, MA 01854 (United States); Vaillancourt, Jarrod [Applied NanoFemto Technologies, LLC, 181 Stedman St. 2, Lowell, MA 01851 (United States)

    2014-03-31

    In this work, we fabricated, measured and compared the quantum dots infrared photodetector enhancement by the top- and backside- configured plasmonic structures. The backside configured plasmonic structure can provide much higher device performance enhancement. Furthermore, the excitation of the surface plasmonic waves by the top- and backside- configured plasmonic structures was analyzed. Detailed simulation results of the electric field at different wavelength from top illumination and backside illumination were provided. The stronger electric field from the backside illumination attributed to the higher enhancement.

  13. Voltage Dependence of Supercapacitor Capacitance

    Directory of Open Access Journals (Sweden)

    Szewczyk Arkadiusz

    2016-09-01

    Full Text Available Electronic Double-Layer Capacitors (EDLC, called Supercapacitors (SC, are electronic devices that are capable to store a relatively high amount of energy in a small volume comparing to other types of capacitors. They are composed of an activated carbon layer and electrolyte solution. The charge is stored on electrodes, forming the Helmholtz layer, and in electrolyte. The capacitance of supercapacitor is voltage- dependent. We propose an experimental method, based on monitoring of charging and discharging a supercapacitor, which enables to evaluate the charge in an SC structure as well as the Capacitance-Voltage (C-V dependence. The measurement setup, method and experimental results of charging/discharging commercially available supercapacitors in various voltage and current conditions are presented. The total charge stored in an SC structure is proportional to the square of voltage at SC electrodes while the charge on electrodes increases linearly with the voltage on SC electrodes. The Helmholtz capacitance increases linearly with the voltage bias while a sublinear increase of total capacitance was found. The voltage on SC increases after the discharge of electrodes due to diffusion of charges from the electrolyte to the electrodes. We have found that the recovery voltage value is linearly proportional to the initial bias voltage value.

  14. Typology of Product Configuration Systems

    DEFF Research Database (Denmark)

    Jensen, Klaes Ladeby; Edwards, Kasper; Haug, Anders

    2007-01-01

    Many organisations are moving from mass production to mass customization. Product configuration systems (PCS) are increasingly seen as an interesting option for firms who wish to pursue a strategy with a high degree of product variance while retaining a low cost of specifying the product. To become...... more specific in relation to how product configuration systems can support mass customization, it is necessary to understand how different product configuration systems can be classified, and how these differ. This paper presents a typology of product configuration systems based on the five kinds...

  15. A Software Configuration Management Course

    DEFF Research Database (Denmark)

    Asklund, U.; Bendix, Lars Gotfred

    2003-01-01

    Software Configuration Management has been a big success in research and creation of tools. There are also many vendors in the market of selling courses to companies. However, in the education sector Software Configuration Management has still not quite made it - at least not into the university...... and contents of such a course....

  16. Heisenberg model and Rigged Configurations

    CERN Document Server

    Giri, Pulak Ranjan

    2015-01-01

    We show a correspondence of all the solutions of the spin-1/2 isotropic Heisenberg model for N=12 to the rigged configurations based on the comparison of the set of Takahashi quantum numbers in lexicographical order with the set of riggings of the rigged configurations in co-lexicographical order.

  17. Configurational entropy of glueball states

    Science.gov (United States)

    Bernardini, Alex E.; Braga, Nelson R. F.; da Rocha, Roldão

    2017-02-01

    The configurational entropy of glueball states is calculated using a holographic description. Glueball states are represented by a supergravity dual picture, consisting of a 5-dimensional graviton-dilaton action of a dynamical holographic AdS/QCD model. The configurational entropy is studied as a function of the glueball spin and of the mass, providing information about the stability of the glueball states.

  18. Application of Configurators in Networks

    DEFF Research Database (Denmark)

    Malis, Martin; Hvam, Lars

    2003-01-01

    a structured guideline, tools and methods on how to successfully develop configurators in a network perspective. Findings presented in this paper are supported by research in a case company. The results from the empirical work show a huge potential for the application of configurators in networks of companies....

  19. Interface circuit with adjustable bias voltage enabling maximum power point tracking of capacitive energy harvesting devices

    Science.gov (United States)

    Wei, J.; Lefeuvre, E.; Mathias, H.; Costa, F.

    2016-12-01

    The operation analysis of a new interface circuit for electrostatic vibration energy harvesting with adjustable bias voltage is carried out in this paper. Two configurations determined by the open or closed states of an electronic switch are examined. The increase of the voltage across a biasing capacitor, occurring when the switch is open, is proved theoretically and experimentally. With the decrease of this biasing voltage which occurs naturally when the switch is closed due to imperfections of the circuit, the bias voltage can be maintained close to a target value by appropriate ON and OFF control of the switch. As the energy converted by the variable capacitor on each cycle depends on the bias voltage, this energy can be therefore accurately controlled. This feature opens up promising perspectives for optimization the power harvested by electrostatic devices. Simulation results with and without electromechanical coupling effect are presented. In experimental tests, a simple switch control enabling to stabilize the bias voltage is described.

  20. A Generalised Fault Protection Structure Proposed for Uni-grounded Low-Voltage AC Microgrids

    Science.gov (United States)

    Bui, Duong Minh; Chen, Shi-Lin; Lien, Keng-Yu; Jiang, Jheng-Lun

    2016-04-01

    This paper presents three main configurations of uni-grounded low-voltage AC microgrids. Transient situations of a uni-grounded low-voltage (LV) AC microgrid (MG) are simulated through various fault tests and operation transition tests between grid-connected and islanded modes. Based on transient simulation results, available fault protection methods are proposed for main and back-up protection of a uni-grounded AC microgrid. In addition, concept of a generalised fault protection structure of uni-grounded LVAC MGs is mentioned in the paper. As a result, main contributions of the paper are: (i) definition of different uni-grounded LVAC MG configurations; (ii) analysing transient responses of a uni-grounded LVAC microgrid through line-to-line faults, line-to-ground faults, three-phase faults and a microgrid operation transition test, (iii) proposing available fault protection methods for uni-grounded microgrids, such as: non-directional or directional overcurrent protection, under/over voltage protection, differential current protection, voltage-restrained overcurrent protection, and other fault protection principles not based on phase currents and voltages (e.g. total harmonic distortion detection of currents and voltages, using sequence components of current and voltage, 3I0 or 3V0 components), and (iv) developing a generalised fault protection structure with six individual protection zones to be suitable for different uni-grounded AC MG configurations.

  1. BRIDGING THE DIGITAL DIVIDE: WITH SPECIAL REFERENCE TO ...

    African Journals Online (AJOL)

    This paper describes the digital divide in Africa with special reference to Nigeria ... south. This digital divide also exists within the countries of the south, between the ... enterprises (SMEs) (Ugboma, 2010) Bridging the digital divide will help to ... resources are being diverted towards meeting the challenges of the pandemic in.

  2. Voltage-Mode All-Pass Filters Using Universal Voltage Conveyor and MOSFET-Based Electronic Resistors

    Directory of Open Access Journals (Sweden)

    N. Herencsar

    2011-04-01

    Full Text Available The paper presents two novel realizations of voltage-mode first-order all-pass filters. Both circuits use single universal voltage conveyor (UVC, single capacitor, and two grounded resistors. Using the two NMOS transistors-based realizations of the electronic resistor with two symmetrical power supplies, presented all-pass filter circuits can be easily made electronically tunable. Proposed filter structures provide both inverting and non-inverting outputs at the same configuration simultaneously and they have high-input and low-output impedances that are desired for easy cascading in voltage-mode operations. The nonidealities of the proposed circuits are also analyzed and compared. The theoretical results of both circuits are verified by SPICE simulations using TSMC 0.35 μm CMOS process parameters. Based on the evaluation, the behavior of one of the circuits featuring better performance was also experimentally measured using the UVC-N1C 0520 integrated circuit.

  3. Method and system for a gas tube switch-based voltage source high voltage direct current transmission system

    Energy Technology Data Exchange (ETDEWEB)

    She, Xu; Chokhawala, Rahul Shantilal; Zhou, Rui; Zhang, Di; Sommerer, Timothy John; Bray, James William

    2016-12-13

    A voltage source converter based high-voltage direct-current (HVDC) transmission system includes a voltage source converter (VSC)-based power converter channel. The VSC-based power converter channel includes an AC-DC converter and a DC-AC inverter electrically coupled to the AC-DC converter. The AC-DC converter and a DC-AC inverter include at least one gas tube switching device coupled in electrical anti-parallel with a respective gas tube diode. The VSC-based power converter channel includes a commutating circuit communicatively coupled to one or more of the at least one gas tube switching devices. The commutating circuit is configured to "switch on" a respective one of the one or more gas tube switching devices during a first portion of an operational cycle and "switch off" the respective one of the one or more gas tube switching devices during a second portion of the operational cycle.

  4. New Configuration of Traction Converter with Medium-Frequency Transformer: Primary Part

    Directory of Open Access Journals (Sweden)

    Vojtech Blahnik

    2008-01-01

    Full Text Available This paper deals with new configuration of the traction converter with medium-frequency transformer intended for ac trolley wire fed locomotives. It is concerned to the primary serially connected single-phase voltage-source active rectifiers, which are directly connected to the trolley wire. This contribution presents the proposed control of the primary active rectifiers, simulation and experimental results of designed low-voltage laboratory prototype of converter of rated power of 12kW.

  5. Wideband radial power combiner/divider fed by a mode transducer

    Science.gov (United States)

    Epp, Larry W. (Inventor); Hoppe, Daniel J. (Inventor); Kelley, Daniel (Inventor); Khan, Abdur R. (Inventor)

    2008-01-01

    A radial power combiner/divider capable of a higher order (for example, N=24) of power combining/dividing and a 15% bandwidth (31 to 36 GHz). The radial power combiner/divider generally comprises an axially-oriented mode transducer coupled to a radial base. The mode transducer transduces circular TE01 waveguide into rectangular TE10 waveguide, and the unique radial base combines/divides a plurality of peripheral rectangular waveguide ports into a single circular TE01 waveguide end of the transducer. The radial base incorporates full-height waveguides that are stepped down to reduced-height waveguides to form a stepped-impedance configuration, thereby reducing the height of the waveguides inside the base and increasing the order N of combining/dividing. The reduced-height waveguides in the base converge radially to a matching post at the bottom center of the radial base which matches the reduced height rectangular waveguides into the circular waveguide that feeds the mode transducer.

  6. Rosette Central Configurations, Degenerate central configurations and bifurcations

    CERN Document Server

    Lei, Jinzhi

    2009-01-01

    In this paper we find a class of new degenerate central configurations and bifurcations in the Newtonian $n$-body problem. In particular we analyze the Rosette central configurations, namely a coplanar configuration where $n$ particles of mass $m_1$ lie at the vertices of a regular $n$-gon, $n$ particles of mass $m_2$ lie at the vertices of another $n$-gon concentric with the first, but rotated of an angle $\\pi/n$, and an additional particle of mass $m_0$ lies at the center of mass of the system. This system admits two mass parameters $\\mu=m_0/m_1$ and $\\ep=m_2/m_1$. We show that, as $\\mu$ varies, if $n> 3$, there is a degenerate central configuration and a bifurcation for every $\\ep>0$, while if $n=3$ there is a bifurcations only for some values of $\\epsilon$.

  7. Effect of voltage shape of electrical power supply on radiation and density of a cold atmospheric argon plasma jet

    OpenAIRE

    F. Sohbatzadeh; Bagheri, M; S. Motallebi

    2017-01-01

    In this work, we investigated generating argon cold plasma jet at atmospheric pressure based on dielectric barrier discharge configuration using three electrical power supplies of sinusoidal, pulsed and saw tooth high voltage shapes at 8 KHZ. At first; we describe the electronic circuit features for generating high voltage (HV) wave forms including saw tooth, sinusoidal and pulsed forms. Then, we consider the effect of voltage shape on the electrical breakdown. Relative concentrations of chem...

  8. Digital divide in education : a shift to ethical usage

    OpenAIRE

    2014-01-01

    Under the trend of ICT implementation in education, students’ learning becomes highly reliant on ICT. A student will thus suffer in his / her learning process if he / she lacks the chance of using ICT at home. This is what a divide in student’s learning is. As the occurrence of this divide is due to digital ICT devices and its effect is focussed on students’ academic performance, such divide is termed as digital divide in education (DDE). To bridge this divide, most governments around the wor...

  9. Unequal Input Voltages Distribution Between the Serial Connected Halfbridges

    Directory of Open Access Journals (Sweden)

    Radovan Ovcarcik

    2006-01-01

    Full Text Available This paper describes a topology of DC-DC converter consisting in two serial connected half-bridges. Secondary circuit is realized like a conventional full-wave rectifier. The main advantage of this topology is the possibility of dividing the input voltage between the half-bridges. The converter is controlled using the phase-shift modulation, which allows a ZVSoperation mode. The voltage unbalance between the inputs causes an important problem of the presented topology. It is necessary to avoid it by the control algorithm, which is described in the text. The practical results show a zero voltage switching technique and the limits of the chosen topology and of the control.

  10. Origin of the transition voltage in gold–vacuum–gold atomic junctions

    KAUST Repository

    Wu, Kunlin

    2012-12-13

    The origin and the distance dependence of the transition voltage of gold-vacuum-gold junctions are investigated by employing first-principles quantum transport simulations. Our calculations show that atomic protrusions always exist on the electrode surface of gold-vacuum-gold junctions fabricated using the mechanically controllable break junction (MCBJ) method. The transition voltage of these gold-vacuum-gold junctions with atomically sharp electrodes is determined by the local density of states (LDOS) of the apex gold atom on the electrode surface rather than by the vacuum barrier shape. More specifically, the absolute value of the transition voltage roughly equals the rising edge of the LDOS peak contributed by the 6p atomic orbitals of the gold atoms protruding from the electrode surface, whose local Fermi level is shifted downwards when a bias voltage is applied. Since the LDOS of the apex gold atom depends strongly on the exact shape of the electrode, the transition voltage is sensitive to the variation of the atomic configuration of the junction. For asymmetric junctions, the transition voltage may also change significantly depending on the bias polarity. Considering that the occurrence of the transition voltage requires the electrode distance to be larger than a critical value, the interaction between the two electrodes is actually rather weak. Consequently, the LDOS of the apex gold atom is mainly determined by its local atomic configuration and the transition voltage only depends weakly on the electrode distance as observed in the MCBJ experiments. © 2013 IOP Publishing Ltd.

  11. Origin of the transition voltage in gold-vacuum-gold atomic junctions.

    Science.gov (United States)

    Wu, Kunlin; Bai, Meilin; Sanvito, Stefano; Hou, Shimin

    2013-01-18

    The origin and the distance dependence of the transition voltage of gold-vacuum-gold junctions are investigated by employing first-principles quantum transport simulations. Our calculations show that atomic protrusions always exist on the electrode surface of gold-vacuum-gold junctions fabricated using the mechanically controllable break junction (MCBJ) method. The transition voltage of these gold-vacuum-gold junctions with atomically sharp electrodes is determined by the local density of states (LDOS) of the apex gold atom on the electrode surface rather than by the vacuum barrier shape. More specifically, the absolute value of the transition voltage roughly equals the rising edge of the LDOS peak contributed by the 6p atomic orbitals of the gold atoms protruding from the electrode surface, whose local Fermi level is shifted downwards when a bias voltage is applied. Since the LDOS of the apex gold atom depends strongly on the exact shape of the electrode, the transition voltage is sensitive to the variation of the atomic configuration of the junction. For asymmetric junctions, the transition voltage may also change significantly depending on the bias polarity. Considering that the occurrence of the transition voltage requires the electrode distance to be larger than a critical value, the interaction between the two electrodes is actually rather weak. Consequently, the LDOS of the apex gold atom is mainly determined by its local atomic configuration and the transition voltage only depends weakly on the electrode distance as observed in the MCBJ experiments.

  12. Voltage Sensors Monitor Harmful Static

    Science.gov (United States)

    2009-01-01

    A tiny sensor, small enough to be worn on clothing, now monitors voltage changes near sensitive instruments after being created to alert Agency workers to dangerous static buildup near fuel operations and avionics. San Diego s Quasar Federal Systems received a Small Business Innovation Research (SBIR) contract from Kennedy Space Center to develop its remote voltage sensor (RVS), a dime-sized electrometer designed to measure triboelectric changes in the environment. One of the unique qualities of the RVS is that it can detect static at greater distances than previous devices, measuring voltage changes from a few centimeters to a few meters away, due to its much-improved sensitivity.

  13. Optimal planning of high voltage distribution substations

    Institute of Scientific and Technical Information of China (English)

    YU Yixin; YAN Xuefei; ZHANG Yongwu

    2007-01-01

    Aimed at solving the problem of optimal planning for high voltage distribution substations,an efficient method is put forward.The method divides the problem into two sub-problems:source locating and combinational optimization.The algorithm of allocating and locating alternatively (ALA) is widely used to deal with the source locating problem,but it is dependent on the initial location to a large degree.Thus,some modifications were made to the ALA algorithm,which could greatly improve the quality of solutions.In addition,considering the non-convex and nonconcave nature of the sub-problem of combinational optimization,the branch-and-bound technique was adopted to obtain or approximate a global optimal solution.To improve the efficiency of the branch-and-bound technique,some heuristic principles were proposed to cut those branches that may generate a global optimization solution with low probability.Examples show that the proposed algorithm meets the requirement of engineering and it is an effective approach to rapidly solve the problem of optimal planning for high voltage distribution substations.

  14. Configuration Spaces in Fundamental Physics

    CERN Document Server

    Anderson, Edward

    2015-01-01

    I consider configuration spaces for $N$-body problems, gauge theories and for GR in both geometrodynamical and Ashtekar variables forms, including minisuperspace and inhomogeneous perturbations thereabout in the former case. These include many interesting spaces of shapes (with and without whichever of local or global notions of scale). In considering reduced configuration spaces, stratified manifolds arise. Three strategies to deal with these are `excise', `unfold' and `accept'. I show that spaces of triangles arising from various interpretations of 3-body problems already serve as model arena for all three. I furthermore argue in favour of the `accept' strategy on relational grounds. Sheaf methods then become relevant in this case, as does the stratifold construct that pairs some well-behaved stratified manifolds with sheaves. I apply arguing against `excise' and `unfold' to GR's superspace and thin sandwich, and to the removal of collinear configurations in mechanics. Non-redundant configurations are also ...

  15. Configuration entropy of fractal landscapes

    National Research Council Canada - National Science Library

    Rodríguez‐Iturbe, Ignacio; D'Odorico, Paolo; Rinaldo, Andrea

    1998-01-01

    .... The spatial arrangement of two‐dimensional images is found to be an effective way to characterize fractal landscapes and the configurational entropy of these arrangements imposes demanding conditions for models attempting to represent these fields.

  16. SAMI Automated Plug Plate Configuration

    CERN Document Server

    Lorente, Nuria P F; Goodwin, Michael

    2012-01-01

    The Sydney-AAO Multi-object Integral field spectrograph (SAMI) is a prototype wide-field system at the Anglo-Australian Telescope (AAT) which uses a plug-plate to mount its 13 x 61-core imaging fibre bundles (hexabundles) in the optical path at the telescope's prime focus. In this paper we describe the process of determining the positions of the plug-plate holes, where plates contain three or more stacked observation configurations. The process, which up until now has involved several separate processes and has required significant manual configuration and checking, is now being automated to increase efficiency and reduce error. This is carried out by means of a thin Java controller layer which drives the configuration cycle. This layer controls the user interface and the C++ algorithm layer where the plate configuration and optimisation is carried out. Additionally, through the Aladin display package, it provides visualisation and facilitates user verification of the resulting plates.

  17. Magnetic configuration control of ITER plasmas

    Energy Technology Data Exchange (ETDEWEB)

    Albanese, R.; Mattei, M. [Assoc. Euratom-ENEA-CREATE, Univ. Mediterranea RC, Loc. Feo di Vito I-89060, RC (Italy); Portone, A. [EFDA-CSU, Max Planck Institute for Plasmaphysics, Boltzmannstrasse 2, D-85748 Garching (Germany)], E-mail: alfredo.portone@tech.efda.org; Ambrosino, G. [Assoc. Euratom-ENEA-CREATE, University Napoli Federico II, Via Claudio 21, I-80125 Naples (Italy); Artaserse, G. [Assoc. Euratom-ENEA-CREATE, Univ. Mediterranea RC, Loc. Feo di Vito I-89060, RC (Italy); Crisanti, F. [Associazione EURATOM-ENEA sulla Fusione, Frascati, C.P. 65, 00044-Frascati (Italy); De Tommasi, G. [Assoc. Euratom-ENEA-CREATE, University Napoli Federico II, Via Claudio 21, I-80125 Naples (Italy); Fresa, R. [DIFA, University della Basilicata, Contrada Macchia Romana I-85100, PZ (Italy); Sartori, F. [Euratom/UKAEA Fusion Assoc., Culham Science Centre, Abingdon, Oxon OX14 3DB (United Kingdom); Villone, F. [Assoc. Euratom-ENEA-CREATE, University Cassino, Via Di Biasio 43, I-03043 Cassino (Italy)

    2007-10-15

    The aim of this paper is to present some new tools used to review the capability of the ITER Poloidal Field (PF) system in controlling the broad range of plasma configurations presently forecasted during ITER operation. The attention is focused on the axi-symmetric aspects of plasma magnetic configuration control since they pose the greatest challenges in terms of control power and they have the largest impact on machine capital cost. Some preliminary results obtained during ongoing activities in collaboration between ENEA/CREATE and EFDA are presented. The paper is divided in two main parts devoted, respectively, to the presentation of a procedure for the PF current optimisation during the scenario, and of a software environment for the study of the PF system capabilities using the plasma linearized response. The proposed PF current optimisation procedure is then used to assess Scenario 2 design, also taking into account the presence of axisymmetric eddy currents and possible variations of poloidal beta and internal inductance. The numerical linear model based tool derived from the JET oriented eXtreme Shape Controller (XSC) tools is finally used to obtain results on the strike point sweeping in ITER.

  18. Configured fuel briquet and method

    Energy Technology Data Exchange (ETDEWEB)

    Peters, S.M.

    1985-01-29

    A charcoal briquet of any selected shape is configured to provide a preselected ignition time and total burning time response. A method of constructing such a briquet for any desired combustion response includes empirically deriving expressions for ignition time as a function of briquet volume, surface area and density, and for burn time as a function of volume and density, and configuring any selected shape briquet in accordance with the parameters found to provide such selected performance.

  19. Low Voltage Power Supply Incorporating Ceramic Transformer

    CERN Document Server

    Imori, M

    2007-01-01

    A low voltage power supply provides the regulated output voltage of 1 V from the supply voltage around 48 V. The low voltage power supply incorporates a ceramic transformer which utilizes piezoelectric effect to convert voltage. The ceramic transformer isolates the secondary from the primary, thus providing the ground isolation between the supply and the output voltages. The ceramic transformer takes the place of the conventional magnetic transformer. The ceramic transformer is constructed from a ceramic bar and does not include any magnetic material. So the low voltage power supply can operate under a magnetic field. The output voltage is stabilized by feedback. A feedback loop consists of an error amplifier, a voltage controlled oscillator and a driver circuit. The amplitude ratio of the transformer has dependence on the frequency, which is utilized to stabilize the output voltage. The low voltage power supply is investigated on the analogy of the high voltage power supply similarly incorporating the cerami...

  20. Modular High Voltage Power Supply

    Energy Technology Data Exchange (ETDEWEB)

    Newell, Matthew R. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2017-05-18

    The goal of this project is to develop a modular high voltage power supply that will meet the needs of safeguards applications and provide a modular plug and play supply for use with standard electronic racks.

  1. A Stochastic Response Surface Method for Probabilistic Evaluation of the Voltage Stability Considering Wind Power

    Institute of Scientific and Technical Information of China (English)

    BAO Haibo; WEI Hua

    2012-01-01

    The traditional voltage stability analysis method is mostly based on the deterministic model, and ignores the uncertainties of bus loads, power supplies, changes in network configuration and so on. However, the great expansion of renewable power generations such as wind and solar energy in a power system has increased their uncertainty, and traditional techniques are limited in capturing their variable behavior. This leads to greater needs of new techniques and methodologies to properly quantify the voltage stability of power systems.

  2. Development of Medium-Voltage and Large-Capacity Uninterruptible Power Supply System

    Science.gov (United States)

    Fujii, Kansuke; Kikuchi, Takayuki; Yoda, Kazuyuki

    A 2-MVA uninterruptible power supply (UPS) system has been developed for compensating for voltage dips in a medium voltage network. The UPS system realizes a high efficiency (99.7%) during single-pulse switching. In this paper, the UPS configurations, storage devices, and transfer switches are compared. Thereafter, the details of the UPS system, the results of the short-circuit test and the system efficiencies are described.

  3. Reliability criteria for voltage stability

    Energy Technology Data Exchange (ETDEWEB)

    Taylor, Carson W.; Silverstein, Brian L. [Bonneville Power Administration, Portland, OR (United States)

    1994-12-31

    In face of costs pressures, there is need to allocate scare resources more effectively in order to achieve voltage stability. This naturally leads to development of probabilistic criteria and notions of rick management. In this paper it is presented a discussion about criteria for long term voltage stability limited to the case in which the time frames are topically several minutes. (author) 14 refs., 1 fig.

  4. A Voltage Quality Detection Method

    DEFF Research Database (Denmark)

    Chen, Zhe; Wei, Mu

    2008-01-01

    This paper presents a voltage quality detection method based on a phase-locked loop (PLL) technique. The technique can detect the voltage magnitude and phase angle of each individual phase under both normal and fault power system conditions. The proposed method has the potential to evaluate vario...... power quality disturbances, such as interruptions, sags and imbalances. Simulation studies have been performed. The effectiveness of the proposed method has been demonstrated under the simulated typical power disturbances....

  5. High-Voltage, Asymmetric-Waveform Generator

    Science.gov (United States)

    Beegle, Luther W.; Duong, Tuan A.; Duong, Vu A.; Kanik, Isik

    2008-01-01

    The shapes of waveforms generated by commercially available analytical separation devices, such as some types of mass spectrometers and differential mobility spectrometers are, in general, inadequate and result in resolution degradation in output spectra. A waveform generator was designed that would be able to circumvent these shortcomings. It is capable of generating an asymmetric waveform, having a peak amplitude as large as 2 kV and frequency of several megahertz, which can be applied to a capacitive load. In the original intended application, the capacitive load would consist of the drift plates in a differential-mobility spectrometer. The main advantage to be gained by developing the proposed generator is that the shape of the waveform is made nearly optimum for various analytical devices requiring asymmetric-waveform such as differential-mobility spectrometers. In addition, this waveform generator could easily be adjusted to modify the waveform in accordance with changed operational requirements for differential-mobility spectrometers. The capacitive nature of the load is an important consideration in the design of the proposed waveform generator. For example, the design provision for shaping the output waveform is based partly on the principle that (1) the potential (V) on a capacitor is given by V=q/C, where C is the capacitance and q is the charge stored in the capacitor; and, hence (2) the rate of increase or decrease of the potential is similarly proportional to the charging or discharging current. The proposed waveform generator would comprise four functional blocks: a sine-wave generator, a buffer, a voltage shifter, and a high-voltage switch (see Figure 1). The sine-wave generator would include a pair of operational amplifiers in a feedback configuration, the parameters of which would be chosen to obtain a sinusoidal timing signal of the desired frequency. The buffer would introduce a slight delay (approximately equal to 20 ns) but would otherwise

  6. A matter of quantum voltages.

    Science.gov (United States)

    Sellner, Bernhard; Kathmann, Shawn M

    2014-11-14

    Voltages inside matter are relevant to crystallization, materials science, biology, catalysis, and aqueous chemistry. The variation of voltages in matter can be measured by experiment, however, modern supercomputers allow the calculation of accurate quantum voltages with spatial resolutions of bulk systems well beyond what can currently be measured provided a sufficient level of theory is employed. Of particular interest is the Mean Inner Potential (V(o))--the spatial average of these quantum voltages referenced to the vacuum. Here we establish a protocol to reliably evaluate V(o) from quantum calculations. Voltages are very sensitive to the distribution of electrons and provide metrics to understand interactions in condensed phases. In the present study, we find excellent agreement with measurements of V(o) for vitrified water and salt crystals and demonstrate the impact of covalent and ionic bonding as well as intermolecular/atomic interactions. Certain aspects in this regard are highlighted making use of simple model systems/approximations. Furthermore, we predict V(o) as well as the fluctuations of these voltages in aqueous NaCl electrolytes and characterize the changes in their behavior as the resolution increases below the size of atoms.

  7. VOLTAGE COMPENSATION USING ARTIFICIAL NEURAL NETWORK

    African Journals Online (AJOL)

    VOLTAGE COMPENSATION USING ARTIFICIAL NEURAL NETWORK: A CASE STUDY OF RUMUOLA DISTRIBUTION NETWORK. ... The artificial neural networks controller engaged to controlling the dynamic voltage ... Article Metrics.

  8. Basic Characteristics of New Developed Higher-Voltage Direct-Current Power-Feeding Prototype System

    Science.gov (United States)

    Babasaki, Tadatoshi; Tanaka, Toshimitsu; Tanaka, Toru; Nozaki, Yousuke; Aoki, Tadahito; Kurokawa, Fujio

    High efficiency power feeding systems are effective solutions for reducing the ICT power consumption with reducing power consumption of the ICT equipment and cooling systems. A higher voltage direct current (HVDC) power feeding system prototype was produced. This system is composed of a rectifier equipment, power distribution unit, batteries, and the ICT equipment. The configuration is similar to a -48V DC power supply system. The output of the rectifier equipment is 100kW, and the output voltage is 401.4V. This paper present the configuration of the HVDC power feeding system and discuss its basic characteristics in the prototype system.

  9. An Empirical Analysis of the Determinants of International Digital Divide

    Science.gov (United States)

    Yun, Liu

    International Digital Divide is an imbalance state of ICT penetration between countries. This paper analyzes the current status and trends of international digital divide, adopts Gompertz technology diffusion model to verify the determinants of ICT penetration level and diffusion rate separately. Finally, China should use "policy levers" to strengthen international trade cooperation, improve the capability of independent innovation, and achieve Chinese goal of bridging digital divide.

  10. Reactive dividing wall column for hydrolysis of methyl acetate:Design and control☆

    Institute of Scientific and Technical Information of China (English)

    Lumin Li; Lanyi Sun; Delian Yang; Wang Zhong; Yi Zhu; Yuanyu Tian

    2016-01-01

    Reactive distillation and dividing wall column distillation are two kinds of effective separation technologies, and their integrated configuration, reactive dividing wall column (RDWC), presents attractive advantages. In this study, the rigorous simulation of RDWC for methyl acetate hydrolysis is performed, and sensitivity analysis is conducted to obtain the minimum reboiler duty. Then a comparison is made between the conventional process and RDWC process, and it shows that 20.1%energy savings can be achieved by RDWC process. In addition, the dynamic characteristic of RDWC is studied and an effective control strategy is proposed. The simple PI control scheme with three temperature loops can obtain reasonable control performance and maintain products at de-sired purities. It is proved that this RDWC process is an energy efficiency alternative with good controllability. © 2016 The Chemical Industry and Engineering Society of China, and Chemical Industry Press. Al rights reserved.

  11. Spin Backflow and ac Voltage Generation by Spin Pumping and the Inverse Spin Hall Effect

    Science.gov (United States)

    Jiao, HuJun; Bauer, Gerrit E. W.

    2013-05-01

    The spin current pumped by a precessing ferromagnet into an adjacent normal metal has a constant polarization component parallel to the precession axis and a rotating one normal to the magnetization. The former is now routinely detected as a dc voltage induced by the inverse spin Hall effect (ISHE). Here we compute ac ISHE voltages much larger than the dc signals for various material combinations and discuss optimal conditions to observe the effect. The backflow of spin is shown to be essential to distill parameters from measured ISHE voltages for both dc and ac configurations.

  12. A high-speed CMOS current op amp for very low supply voltage operation

    DEFF Research Database (Denmark)

    Bruun, Erik

    1994-01-01

    A CMOS implementation of a high-gain current mode operational amplifier (op amp) with a single-ended input and a differential output is described. This configuration is the current mode counterpart of the traditional voltage mode op amp. In order to exploit the inherent potential for high speed......, low voltage operation normally associated with current mode analog signal processing, the op amp has been designed to operate off a supply voltage of 1.5 V, and the signal path has been confined to N-channel transistors. With this design, a gain of 94 dB and a gain-bandwidth product of 65 MHz has been...

  13. BAYESIAN IMAGE RESTORATION, USING CONFIGURATIONS

    Directory of Open Access Journals (Sweden)

    Thordis Linda Thorarinsdottir

    2011-05-01

    Full Text Available In this paper, we develop a Bayesian procedure for removing noise from images that can be viewed as noisy realisations of random sets in the plane. The procedure utilises recent advances in configuration theory for noise free random sets, where the probabilities of observing the different boundary configurations are expressed in terms of the mean normal measure of the random set. These probabilities are used as prior probabilities in a Bayesian image restoration approach. Estimation of the remaining parameters in the model is outlined for salt and pepper noise. The inference in the model is discussed in detail for 3 X 3 and 5 X 5 configurations and examples of the performance of the procedure are given.

  14. Ringed accretion disks: equilibrium configurations

    CERN Document Server

    Pugliese, D

    2015-01-01

    We investigate a model of ringed accretion disk, made up by several rings rotating around a supermassive Kerr black hole attractor. Each toroid of the ringed disk is governed by the General Relativity hydrodynamic Boyer condition of equilibrium configurations of rotating perfect fluids. Properties of the tori can be then determined by an appropriately defined effective potential reflecting the background Kerr geometry and the centrifugal effects. The ringed disks could be created in various regimes during the evolution of matter configurations around supermassive black holes. Therefore, both corotating and counterrotating rings have to be considered as being a constituent of the ringed disk. We provide constraints on the model parameters for the existence and stability of various ringed configurations and discuss occurrence of accretion onto the Kerr black hole and possible launching of jets from the ringed disk. We demonstrate that various ringed disks can be characterized by a maximum number of rings. We pr...

  15. Electrode voltage fall and total voltage of a transient arc

    Science.gov (United States)

    Valensi, F.; Ratovoson, L.; Razafinimanana, M.; Masquère, M.; Freton, P.; Gleizes, A.

    2016-06-01

    This paper deals with an experimental study of the components of a transient arc total voltage with duration of a few tens of ms and a current peak close to 1000 A. The cathode tip is made of graphite whereas the flat anode is made either of copper or of graphite; the electrodes gap is a few mm. The analysis of the electrical parameters is supported and validated by fast imaging and by two models: the first one is a 2D physical model of the arc allowing to calculate both the plasma temperature field and the arc voltage; the second model is able to estimate the transient heating of the graphite electrode. The main aim of the study was to detect the possible change of the cathode voltage fall (CVF) during the first instants of the arc. Indeed it is expected that during the first ms the graphite cathode is rather cool and the main mechanism of the electron emission should be the field effect emission, whereas after several tens of ms the cathode is strongly heated and thermionic emission should be predominant. We have observed some change in the apparent CVF but we have shown that this apparent change can be attributed to the variation of the solid cathode resistance. On the other hand, the possible change of CVF corresponding to the transition between a ‘cold’ and a ‘hot’ cathode should be weak and could not be characterized considering our measurement uncertainty of about 2 V. The arc column voltage (ACV) was estimated by subtracting the electrode voltage fall from the total arc voltage. The experimental transient evolution of the ACV is in very good agreement with the theoretical variation predicted by the model, showing the good ability of the model to study this kind of transient arc.

  16. Investigation of Shaft Voltage in Wind Turbine Systems with Induction Generators

    Science.gov (United States)

    Adabi, Jafar; Zare, Firuz

    This paper presents the analysis of shaft voltage in different configurations of a doubly fed induction generator (DFIG) and an induction generator (IG) with a back-to-back inverter in wind turbine applications. Detailed high frequency model of the proposed systems have been developed based on existing capacitive couplings in IG & DFIG structures and common mode voltage sources. In this research work, several arrangements of DFIG based wind energy conversion systems (WES) are investigated in case of shaft voltage calculation and its mitigation techniques. Placements of an LC line filter in different locations and its effects on shaft voltage elimination are studied via Mathematical analysis and simulations. A pulse width modulation (PWM) technique and a back-to-back inverter with a bidirectional buck converter have been presented to eliminate the shaft voltage in a DFIG wind turbine.

  17. The Digital Divide and Health Outcomes: A Teleretinal Imaging Study

    Science.gov (United States)

    Connolly, Kathleen Kihmm

    2013-01-01

    The purpose of this research project was to understand, explore and describe the digital divide and the relationship between technology utilization and health outcomes. Diabetes and diabetic eye disease was used as the real-life context for understanding change and exploring the digital divide. As an investigational framework, a telemedicine…

  18. Digital Natives and Digital Divide: Analysing Perspective for Emerging Pedagogy

    Science.gov (United States)

    Onye, Uriel U.; Du, Yunfei

    2016-01-01

    This paper addresses the concepts of digital natives and digital divide from the perspective of the digital outsiders (part of digital natives). It takes a critical look at the implications of available ICT in both developed and underdeveloped countries in the fight against digital divide. The major contribution to literature is by drawing…

  19. The Digital Divide in Health Education: Myth or Reality?

    Science.gov (United States)

    Stellefson, Michael; Chaney, Beth; Chaney, Don

    2008-01-01

    Although e-health interventions provide new opportunities for health education, there has been cause for concern regarding the purported information technology gap between those who have access to digital applications and those who do not--termed the "digital divide." The literature suggests, however, that this divide may now be illusory, driven…

  20. Distance Education and the Digital Divide: An Academic Perspective

    Science.gov (United States)

    Block, Judy

    2010-01-01

    This paper will address how the digital divide affects distance education. Lack of access for some students does raise concerns. Access to technology is often defined by what students don't have: what is called a digital divide. Access also is defined by the speed of Internet connections. Access in the future will be even greater as more computers…

  1. Bridging the Digital Divide--An Australian Story

    Science.gov (United States)

    Broadbent, Robyn; Papadopoulos, Theo

    2013-01-01

    There is increasing evidence that the lack of access to information and communication technology (ICT) or the "digital divide" severely limits education, employment and economic prospects. This paper reports on the evaluation of a project that aims to bridge the digital divide. In particular, the case study data has been used to bring to…

  2. Evaluation of Fatih Project in the Frame of Digital Divide

    Science.gov (United States)

    Karabacak, Kerim

    2016-01-01

    The aim of this research realized at the general survey model is to evaluate "FATIH Project" in the frame of digital divide by determining the effects of the distributed tablets to the students being educated at K-12 schools on digital divide. Sample is taking from the 9th grade students in Sakarya city in the 2013-2014 academic session.…

  3. Rethinking the Digital Divide: Impacts on Student-Tutor Relationships

    Science.gov (United States)

    Underwood, Jean D. M.

    2007-01-01

    This article emerged from a series of debates and workshops on the impact of the Digital Divide on educational practice at the "Futures of Learning: New Learning Paradigms Conference" in Paris. The conceptualisation of the Digital Divide into the "haves" and the "have-nots", with a perception of the economically…

  4. The Digital Divide and Health Outcomes: A Teleretinal Imaging Study

    Science.gov (United States)

    Connolly, Kathleen Kihmm

    2013-01-01

    The purpose of this research project was to understand, explore and describe the digital divide and the relationship between technology utilization and health outcomes. Diabetes and diabetic eye disease was used as the real-life context for understanding change and exploring the digital divide. As an investigational framework, a telemedicine…

  5. Crossing the Phantom divide line in the Chaplygin gas model

    CERN Document Server

    Sadjadi, H Mohseni

    2009-01-01

    The role of the interaction in crossing the phantom divide line in the Chaplygin gas model is discussed. We obtain some general properties of the interactions that allow the model to arrive at the phantom divide line. We show that these properties put some conditions on the ratio of dark matter to dark energy density.

  6. Electrode Configurations in Atmospheric Pressure Plasma Jets

    Science.gov (United States)

    Lietz, Amanda M.; Kushner, Mark J.

    2016-09-01

    Atmospheric pressure plasma jets (APPJs) are being studied for emerging medical applications including cancer treatment and wound healing. APPJs typically consist of a dielectric tube through which a rare gas flows, sometimes with an O2 or H2O impurity. In this paper, we present results from a computational study of APPJs using nonPDPSIM, a 2-D plasma hydrodynamics model, with the goal of providing insights on how the placement of electrodes can influence the production of reactive species. Gas consisting of He/O2 = 99.5/0.5 is flowed through a capillary tube at 2 slpm into humid air, and a pulsed DC voltage is applied. An APPJ with two external ring electrodes will be compared with one having a powered electrode inside and a ground electrode on the outside. The consequences on ionization wave propagation and the production of reactive oxygen and nitrogen species (RONS) will be discussed. Changing the electrode configuration can concentrate the power deposition in volumes having different gas composition, resulting in different RONS production. An internal electrode can result in increased production of NOx and HNOx by increasing propagation of the ionization wave through the He dominated plume to outside of the tube where humid air is diffusing into the plume. Work supported by US DOE Office of Fusion Energy Science and the National Science Foundation.

  7. Three Phase Two Leg Neutral Point Clamped Converter with output DC Voltage Regulation and Input Power Factor Correction

    Directory of Open Access Journals (Sweden)

    Bogimi Sirisha

    2012-03-01

    Full Text Available In this paper, a three-phase two leg neutral point clamped (NPC converter is presented for power factor correction and dc-link voltage regulation. The adopted converter has simpler circuit configuration and less number of power switches compared to three-level PWM converter. In this circuit configuration, only eight power switches and four clamping diodes with voltage stress of half the dc bus voltage are used. A simplified space vector pulse width modulation scheme (SVPWM is also adopted to track the line current commands. A reference voltage vector is generated on the ac terminal for drawing the sinusoidal line currents with unity power factor. This algorithm reduces the time required to calculate the switching time durations of voltage vectors. The simulation results have been presented to verify the validity and effectiveness of the proposed control strategy.

  8. Unbalanced Voltage Compensation in Low Voltage Residential AC Grids

    DEFF Research Database (Denmark)

    Trintis, Ionut; Douglass, Philip; Munk-Nielsen, Stig

    2016-01-01

    This paper describes the design and test of a control algorithm for active front-end rectifiers that draw power from a residential AC grid to feed heat pump loads. The control algorithm is able to control the phase to neutral or phase to phase RMS voltages at the point of common coupling....... The voltage control was evaluated with either active or reactive independent phase load current control. The control performance in field operation in a residential grid situated in Bornholm, Denmark was investigated for different use cases....

  9. Write operation in MRAM with voltage controlled magnetic anisotropy

    Science.gov (United States)

    Munira, Kamaram; Pandey, Sumeet; Sandhu, Gurtej

    In non-volatile Magnetic RAM, information is saved in the bistable configuration of the free layer in a magnetic tunnel junction (MTJ). New information can be written to the free layer through magnetic induction (Toggle MRAM) or manipulation of magnetization using electric currents (Spin Transfer Torque MRAM or STT-MRAM). Both of the writing methods suffer from a shortcoming in terms of energy efficiency. This limitation on energy performance is brought about by the need for driving relatively large electrical charge currents through the devices for switching. In STT-MRAM, the nonzero voltage drop across the resistive MTJ leads to significant power dissipation. An energy efficient way to write may be with the assistance of voltage controlled magnetic anisotropy (VCMA), where voltage applied across the MTJ creates an electric field that modulates the interfacial anisotropy between the insulator and free layer. However, VCMA cannot switch the free layer completely by 180 degree rotation of magnetization. It can lower the barrier between the two stable configurations or at best, cancel the barrier, allowing 90 degree rotation. A second mechanism, spin torque or magnetic field, is needed to direct the final switching destination.

  10. Electronic Configuration of Yb Compounds

    Energy Technology Data Exchange (ETDEWEB)

    Temmerman, W.M.; Szotek, Z. [Daresbury Laboratory, Daresbury, Warrington, WA4 4AD, Cheshire (United Kingdom); Svane, A. [Institute of Physics and Astronomy, University of Aarhus, DK-8000 Aarhus C (Denmark); Strange, P. [Physics Department, Keele University, Keele, Staffordshire, ST5 5BG (United Kingdom); Winter, H. [INFP, Forschungszentrum Karlsruhe GmbH, Postfach 3640, D-76021 Karlsruhe (Germany); Delin, A.; Johansson, B.; Eriksson, O.; Fast, L. [Condensed Matter Theory Group, Department of Physics, University of Uppsala, Box 530, 75121 Uppsala (Sweden); Wills, J.M. [Center of Materials Science and Theoretical Division, Los Alamos National Laboratory, Los Alamos, New Mexico 87544 (United States)

    1999-11-01

    The total energy differences between divalent and trivalent configurations of Yb ions in a number of Yb compounds are studied. Two different band theoretical methods, which differ in the treatment of the localized f electrons, are used. The results show that in all Yb compounds the valence energy differences are equal to the energy needed to localize an f electron. These valence energy differences correlate with the number of f electrons hybridizing with the conduction bands in the trivalent configuration. For divalent YbS, the pressure induced f -electron delocalization implies an intermediate valency, as also indicated by experiment. {copyright} {ital 1999} {ital The American Physical Society }

  11. Product Configuration Systems and Productivity

    DEFF Research Database (Denmark)

    Pedersen, Jørgen Lindgaard; Edwards, Kasper

    2004-01-01

    Twelve companies have been interviewed with the purpose to get information about technical, economic and organisational matters in respect of Product Configuration Systems (PCS).Combinations of qualitative interviews and quantitative scoring have been used in ranking expected and realized results...... from implementing PCS. The three highest aggregated scoring expected benefits are: 1)improved quality in specifications, 2)lower turnaround time, 3)less resource intensity.......Twelve companies have been interviewed with the purpose to get information about technical, economic and organisational matters in respect of Product Configuration Systems (PCS).Combinations of qualitative interviews and quantitative scoring have been used in ranking expected and realized results...

  12. Instance-specific algorithm configuration

    CERN Document Server

    Malitsky, Yuri

    2014-01-01

    This book presents a modular and expandable technique in the rapidly emerging research area of automatic configuration and selection of the best algorithm for the instance at hand. The author presents the basic model behind ISAC and then details a number of modifications and practical applications. In particular, he addresses automated feature generation, offline algorithm configuration for portfolio generation, algorithm selection, adaptive solvers, online tuning, and parallelization.    The author's related thesis was honorably mentioned (runner-up) for the ACP Dissertation Award in 2014,

  13. Network sensitivity to geographical configuration

    CERN Document Server

    Searle, A C; McClelland, D E; Searle, Antony C; Scott, Susan M; Clelland, David E Mc

    2002-01-01

    Gravitational wave astronomy will require the coordinated analysis of data from the global network of gravitational wave observatories. Questions of how to optimally configure the global network naturally arise in this context. We propose a formalism to compare different configurations of the network, using both the coincident network analysis method and the coherent network analysis method, and construct a model to compute a figure-of-merit based on the detection rate for a population of standard-candle binary inspirals. We find that this measure of network quality is very sensitive to the geographic location of component detectors under a coincident network analysis, but comparatively insensitive under a coherent network analysis.

  14. Hexuple-Inverter Configuration for Multilevel Nine-Phase Symmetrical Open-Winding Converter

    DEFF Research Database (Denmark)

    Padmanaban, Sanjeevi Kumar; Bhaskar, Mahajan Sagar; Maroti, Pandav Kiran

    2016-01-01

    Hexuple-inverter configuration for multilevel nine-phase symmetrical open-winding ac converter is articulated in this work. Power modular unit consists of six classical three-phase voltage source inverters (VSI). Each VSI includes one bi-directional device (MOSFET/IGBT) per each phase and link...

  15. Hexuple-Inverter Configuration for Multilevel Nine-Phase Symmetrical Open-Winding Converter

    DEFF Research Database (Denmark)

    Padmanaban, Sanjeevi Kumar; Bhaskar, Mahajan Sagar; Maroti, Pandav Kiran

    2016-01-01

    Hexuple-inverter configuration for multilevel nine-phase symmetrical open-winding ac converter is articulated in this work. Power modular unit consists of six classical three-phase voltage source inverters (VSI). Each VSI includes one bi-directional device (MOSFET/IGBT) per each phase and link to...

  16. A Novel Multilevel Quad-Inverter Configuration for Quasi Six-Phase Open-Winding Converter

    DEFF Research Database (Denmark)

    Padmanaban, Sanjeevi Kumar; Blaabjerg, Frede; Wheeler, Patrick

    2016-01-01

    This paper developed a novel quad-inverter configuration for multilevel six-phase asymmetrical open-winding AC converter. Proposal found to be suited for (low-voltage/high-current) applications such as AC tractions and `More-Electric Aircraft' propulsion systems. Modular power circuit comprises o...

  17. A novel double quad-inverter configuration for multilevel twelve-phase open-winding converter

    DEFF Research Database (Denmark)

    Padmanaban, Sanjeevi Kumar; Blaabjerg, Frede; Wheeler, Patrick William

    2016-01-01

    This paper describes a novel proposal of double quad-inverter configuration for multilevel twelve-phase open-winding ac converter. Modular power units are developed from reconfigured eight classical three-phase voltage source inverters (VSIs). Each VSI has one additional bi-directional switching ...

  18. Low-Energy Real-Time OS Using Voltage Scheduling Algorithm for Variable Voltage Processors

    OpenAIRE

    Okuma, Takanori; Yasuura, Hiroto

    2001-01-01

    This paper presents a real-time OS based on $ mu $ITRON using proposed voltage scheduling algorithm for variable voltage processors which can vary supply voltage dynamically. The proposed voltage scheduling algorithms assign voltage level for each task dynamically in order to minimize energy consumption under timing constraints. Using the presented real-time OS, running tasks with low supply voltage leads to drastic energy reduction. In addition, the presented voltage scheduling algorithm is ...

  19. Simple buck/boost voltage regulator

    Science.gov (United States)

    Paulkovich, J.; Rodriguez, G. E.

    1980-01-01

    Circuit corrects low or high supply voltage, produces regulated output voltage. Circuit has fewer components because inductory/transformer combination and pulse-width modulator serve double duty. Regulator handles input voltage variation from as low as one half output voltage to as high as input transistor rating. Solar arrays, fuel cells, and thermionic generators might use this regulator.

  20. 30 CFR 18.47 - Voltage limitation.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Voltage limitation. 18.47 Section 18.47 Mineral... § 18.47 Voltage limitation. (a) A tool or switch held in the operator's hand or supported against his... particular voltage(s) are provided in the design and construction of the equipment, its wiring,...

  1. Portable High Voltage Impulse Generator

    Directory of Open Access Journals (Sweden)

    S. Gómez

    2011-07-01

    Full Text Available This paper presents a portable high voltage impulse generator which was designed and built with insulation up to 20 kV. This design was based on previous work in which simulation software for standard waves was developed. Commercial components and low-cost components were used in this work; however, these particular elements are not generally used for high voltage applications. The impulse generators used in industry and laboratories are usually expensive; they are built to withstand extra high voltage and they are big, making them impossible to transport. The proposed generator is portable, thereby allowing tests to be made on devices that cannot be moved from their location. The results obtained with the proposed impulse generator were satisfactory in terms of time and waveforms compared to other commercial impulse generators and the standard impulse wave simulator.

  2. Bayesian image restoration, using configurations

    DEFF Research Database (Denmark)

    Thorarinsdottir, Thordis

    configurations are expressed in terms of the mean normal measure of the random set. These probabilities are used as prior probabilities in a Bayesian image restoration approach. Estimation of the remaining parameters in the model is outlined for salt and pepper noise. The inference in the model is discussed...

  3. Bayesian image restoration, using configurations

    DEFF Research Database (Denmark)

    Thorarinsdottir, Thordis Linda

    2006-01-01

    configurations are expressed in terms of the mean normal measure of the random set. These probabilities are used as prior probabilities in a Bayesian image restoration approach. Estimation of the remaining parameters in the model is outlined for the salt and pepper noise. The inference in the model is discussed...

  4. Auralization of novel aircraft configurations

    NARCIS (Netherlands)

    Arntzen, M.; Bertsch, E.L.; Simons, D.G.

    2015-01-01

    A joint initiative of NLR, DLR, and TU Delft has been initiated to streamline the process of generating audible impressions of novel aircraft configurations. The integrated approach adds to the value of the individual tools and allows predicting the sound of future aircraft before they actually fly.

  5. NCCDS configuration management process improvement

    Science.gov (United States)

    Shay, Kathy

    1993-01-01

    By concentrating on defining and improving specific Configuration Management (CM) functions, processes, procedures, personnel selection/development, and tools, internal and external customers received improved CM services. Job performance within the section increased in both satisfaction and output. Participation in achieving major improvements has led to the delivery of consistent quality CM products as well as significant decreases in every measured CM metrics category.

  6. Warehouse Simulation Through Model Configuration

    NARCIS (Netherlands)

    Verriet, J.H.; Hamberg, R.; Caarls, J.; Wijngaarden, B. van

    2013-01-01

    The pre-build development of warehouse systems leads from a specific customer request to a specific customer quotation. This involves a process of configuring a warehouse system using a sequence of steps that contain increasingly more details. Simulation is a helpful tool in analyzing warehouse desi

  7. Kramers Pairs in configuration interaction

    DEFF Research Database (Denmark)

    Avery, John Scales; Avery, James Emil

    2003-01-01

    The theory of symmetry-preserving Kramers pair creation operators is reviewed and formulas for applying these operators to configuration interaction calculations are derived. A new and more general type of symmetry-preserving pair creation operator is proposed and shown to commute with the total...

  8. GEODSS Present Configuration and Potential

    Science.gov (United States)

    2014-06-28

    1. REPORT DATE 28 JUN 2014 2. REPORT TYPE 3. DATES COVERED 00-00-2014 to 00-00-2014 4. TITLE AND SUBTITLE GEODSS Present Configuration and...provides improved resolution and radiometric throughput at low elevation angles versus a single fisheye optical strategy. Both optical systems are

  9. Implementation of Dynamic Voltage Restorer for Mitigation of Voltage Sag

    Directory of Open Access Journals (Sweden)

    K.Vinod Kumar

    2013-07-01

    Full Text Available Power quality is one of major concerns in the present. It has become important, especially with the introduction of sophisticated devices, whose performance is very sensitive to the quality of power supply. The dynamic voltage restorer (DVR is one of the modern devices used in distribution systems to improve the power quality. In this paper, emergency control in distribution systems is discussed by using the proposed multifunctional DVR control strategy.Also, themultiloop controller using the Posicast and P+Resonant controllers is proposed in order to improve the transient response and eliminate the steady state error in DVR response,respectively.The proposed process is applied to some riots in load voltage effected by induction motors starting, and a three-phase short circuit fault. The three-phase short circuits, and the large induction motors are suddenly started then voltage sags areoccurred.The innovation here is that by using the Multifunctional Dynamic Voltage Restorer, improve the power quality in distribution side. Simulation results show the capability of the DVR to control the emergency conditions of the distribution systems by using MATLAB/Simulink software.

  10. Phase space barriers and dividing surfaces in the absence of critical points of the potential energy

    CERN Document Server

    Ezra, Gregory S

    2010-01-01

    We consider the existence of invariant manifolds in phase space governing reaction dynamics in situations where there are no saddle points on the potential energy surface in the relevant regions of configuration space. We point out that such situations occur in a number of important classes of chemical reactions, and we illustrate this concretely by considering a model for transition state switching in an ion-molecule association reaction due to Chesnavich (J. Chem. Phys. {\\bf 84}, 2615 (1986)). For this model we show that, in the region of configuration space relevant to the reaction, there are no saddle points on the potential energy surface, but that in phase space there is a normally hyperbolic invariant manifold (NHIM) bounding a dividing surface having the property that the reactive flux through this dividing surface is a minimum. We then describe two methods for finding NHIMs and their associated phase space structures in systems with more than two degrees-of-freedom. These methods do not rely on the e...

  11. The high voltage homopolar generator

    Science.gov (United States)

    Price, J. H.; Gully, J. H.; Driga, M. D.

    1986-11-01

    System and component design features of proposed high voltage homopolar generator (HVHPG) are described. The system is to have an open circuit voltage of 500 V, a peak output current of 500 kA, 3.25 MJ of stored inertial energy and possess an average magnetic-flux density of 5 T. Stator assembly components are discussed, including the stator, mount structure, hydrostatic bearings, main and motoring brushgears and rotor. Planned operational procedures such as monitoring the rotor to full speed and operation with a superconducting field coil are delineated.

  12. High voltage generator circuit with low power and high efficiency applied in EEPROM

    Institute of Scientific and Technical Information of China (English)

    Liu Yan; Zhang Shilin; Zhao Yiqiang

    2012-01-01

    This paper presents a low power and high efficiency high voltage generator circuit embedded in electrically erasable programmable read-only memory (EEPROM).The low power is minimized by a capacitance divider circuit and a regulator circuit using the controlling clock switch technique.The high efficiency is dependent on the zero threshold voltage (Vth) MOSFET and the charge transfer switch (CTS) charge pump.The proposed high voltage generator circuit has been implemented in a 0.35μm EEPROM CMOS process.Measured results show that the proposed high voltage generator circuit has a low power consumption of about 150.48 μW and a higher pumping efficiency (83.3%) than previously reported circuits.This high voltage generator circuit can also be widely used in low-power flash devices due to its high efficiency and low power dissipation.

  13. Resilient architecture design for voltage variation

    CERN Document Server

    Reddi, Vijay Janapa

    2013-01-01

    Shrinking feature size and diminishing supply voltage are making circuits sensitive to supply voltage fluctuations within the microprocessor, caused by normal workload activity changes. If left unattended, voltage fluctuations can lead to timing violations or even transistor lifetime issues that degrade processor robustness. Mechanisms that learn to tolerate, avoid, and eliminate voltage fluctuations based on program and microarchitectural events can help steer the processor clear of danger, thus enabling tighter voltage margins that improve performance or lower power consumption. We describe

  14. Low Beam Voltage, 10 MW, L-Band Cluster Klystron

    Energy Technology Data Exchange (ETDEWEB)

    Teryaev, V.; /Novosibirsk, IYF; Yakovlev, V.P.; /Fermilab; Kazakov, S.; /KEK, Tsukuba; Hirshfield, J.L.; /Yale U. /Omega-P, New Haven

    2009-05-01

    Conceptual design of a multi-beam klystron (MBK) for possible ILC and Project X applications is presented. The chief distinction between this MBK design and existing 10-MW MBK's is the low operating voltage of 60 kV. There are at least four compelling reasons that justify development at this time of a low-voltage MBK, namely (1) no pulse transformer; (2) no oil tank for high-voltage components and for the tube socket; (3) no high-voltage cables; and (4) modulator would be a compact 60-kV IGBT switching circuit. The proposed klystron consists of four clusters containing six beams each. The tube has common input and output cavities for all 24 beams, and individual gain cavities for each cluster. A closely related optional configuration, also for a 10 MW tube, would involve four totally independent cavity clusters with four independent input cavities and four 2.5 MW output ports, all within a common magnetic circuit. This option has appeal because the output waveguides would not require a controlled atmosphere, and because it would be easier to achieve phase and amplitude stability as required in individual SC accelerator cavities.

  15. Vacuum Circuit Breaker Modelling for the Assessment of Transient Recovery Voltages Under Various Network Configurations

    DEFF Research Database (Denmark)

    Bak, Claus Leth; Borghetti, Alberto; Glasdam, Jakob Bærholm

    2017-01-01

    for both VCB sizing and insulation coordination studies of the components nearby the switching device. In this respect, their accurate modelling, which is the object of the paper, becomes crucial. In particular, the paper presents (the concept of) a VCB model and two relevant applications showing the model......-known electromagnetic transient simulation environments, namely, EMTP-RV and PSCAD/EMTDC. The procedure adopted for the identification of the VCB model parameters is described....

  16. Voltage quality in a naval vessel power system during island configuration

    NARCIS (Netherlands)

    Timens, R.B.; Leersum, van B.J.A.M.; Bijman, R.C.G.; Leferink, F.B.J.

    2012-01-01

    Power networks and installed equipment onboard of naval ships are required to meet military standards. However, technology in the commercial market grows very fast and the use of Commercial Off The Shelf (COTS) products is economically interesting although they are often not certified against requir

  17. Voltage quality in a naval vessel power system during island configuration

    NARCIS (Netherlands)

    Timens, R.B.; van Leersum, B.J.A.M.; Bijman, R.C.G.; Leferink, Frank Bernardus Johannes

    2012-01-01

    Power networks and installed equipment onboard of naval ships are required to meet military standards. However, technology in the commercial market grows very fast and the use of Commercial Off The Shelf (COTS) products is economically interesting although they are often not certified against

  18. Power Restoration in Medium Voltage Network Using Multiagent System

    Directory of Open Access Journals (Sweden)

    Miroslav Kovac

    2013-01-01

    Full Text Available The article describes a novel approach to a power restoration in medium voltage power distribution network. It focuses primary at searching of a new network configuration enabling to minimalize the size of faulted area and to restore the power for the highest possible number of loads. It describes characteristic features of medium voltage power distribution network and discusses the implementation of the presented approach in existing networks. A software tool, developed by the authors, including physical simulation of model network and its autonomous control system is described. An example of fault situation in a virtual distribution network is presented. Afterwards, the solution of restoration problem by proposed multiagent system is simulated using the software tool described in the paper.

  19. Superstrate sub-cell voltage-matched multijunction solar cells

    Energy Technology Data Exchange (ETDEWEB)

    Mascarenhas, Angelo; Alberi, Kirstin

    2016-03-15

    Voltage-matched thin film multijunction solar cell and methods of producing cells having upper CdTe pn junction layers formed on a transparent substrate which in the completed device is operatively positioned in a superstate configuration. The solar cell also includes a lower pn junction formed independently of the CdTe pn junction and an insulating layer between CdTe and lower pn junctions. The voltage-matched thin film multijunction solar cells further include a parallel connection between the CdTe pn junction and lower pn junctions to form a two-terminal photonic device. Methods of fabricating devices from independently produced upper CdTe junction layers and lower junction layers are also disclosed.

  20. The effects of contact configurations on the rectification of dipyrimidinyl-diphenyl diblock molecular junctions

    Institute of Scientific and Technical Information of China (English)

    Zhang Guang-Ping; Hu Gui-Chao; Li Zong-Liang; Wang Chuan-Kui

    2011-01-01

    The transport properties of a conjugated dipyrimidinyl-diphenyl diblock oligomer sandwiched between two gold electrodes,as recently reported by [Díez-Pérez et al.Nature Chem.1 635 (2009)],are theoretically investigated using the fully self-consistent nonequilibrium Green's function method combined with density functional theory.Two kinds of symmetrical anchoring geometries are considered.Calculated current-voltage curves show that the contact structure has a strong effect on the rectification behaviour of the molecular diode.For the equilateral triangle configuration,pronounced rectification behaviour comparable to the experimental measurement is revealed,and the theoretical analysis indicates that the observed rectification characteristic results from the asymmetric shift of the perturbed molecular energy levels under bias voltage.While for the tetrahedron configuration,both rectification and negative differential conductivity behaviours are observed.The calculated results further prove the close dependence of the transporting characteristics of molecular junctions on contact configuration.

  1. VOLTAGE REGULATORS OF SYNCHRONOUS GENERATORS

    Directory of Open Access Journals (Sweden)

    Grigorash O. V.

    2015-06-01

    Full Text Available Synchronous generators are the primary source of electrical power autonomous electrosupply systems, including backup systems. They are also used in a structure of rotating electricity converters and are widely used in renewable energy as part of wind power plants of small, mini and micro hydroelectric plants. Increasing the speed and the accuracy of the system of the voltage regulation of synchronous generators is possible due to the development of combined systems containing more stabilizers. The article illustrates the functional schemes of circuit voltage stabilizers and frequency synchronous generators (with electromagnetic excitation and permanent magnet excitation and describes the features of their work, including two and three-aggregate rotating converters of electricity used in uninterruptible power supply systems. To improve the technical characteristics of the system of stabilization we have proposed functional solutions for stabilizers of synchronous generators made on the base of direct frequency converters and using a transformer with a rotating magnetic field. To improve the reliability of and to improve the operational characteristics of the autonomous independent sources of electricity we suggest creating the main functional blocks and the elements of the stabilization system in a modular way. The functional circuit solutions of voltage regulators of synchronous generators and the characteristics of their work considered in the article, are able to improve the efficiency of pre-design work in the development of new technical solutions for stabilizing the voltage and the frequency in synchronous generators of electrosupply autonomous systems

  2. Frequency-controlled voltage regulator

    Science.gov (United States)

    Mclyman, W. T.

    1980-01-01

    Converting input ac to higher frequency reduce size and weight and makes possible unique kind of regulation. Since conversion frequency is above range of human hearing, supply generated on audible noise. It also exploits highfrequency conversion features to regulate its output voltage in novel way. Circuit is inherently short-circuit proof.

  3. A Line Dividing "Trademark License" and "Trademark Infringement"

    Institute of Scientific and Technical Information of China (English)

    Chi Shaojie

    2004-01-01

    @@ Opinions are not divided on in fringement by another person's use of a registered trademark without license from the trademark registrant,nor on the non-infringement by its/his licensed use of a registered trademark.

  4. Continental Divide of the United States - Direct Download

    Data.gov (United States)

    U.S. Geological Survey, Department of the Interior — This map layer portrays the Continental Divide of the United States. The map layer was created by extracting Hydrologic Unit Boundary line features from an existing...

  5. Annan warns of 'content divide' between rich and poor

    CERN Multimedia

    Dickson, D

    2003-01-01

    "The Secretary-General of the United Nations, Kofi Annan, warned today (10 December) that a "content divide" is threatening to deprive developing countries of the full benefits offered by information and communications technologies (ICTs)" (1 page)

  6. An improved fractional divider for fractional-N frequency synthesizers

    Science.gov (United States)

    Zhang, Wei; Liu, Yang; Zhou, Yongqi

    2009-07-01

    This paper presents an improved fractional divider used in 1.8~2GHz fractional-N frequency synthesizers. A new clock setting for delta-sigma modulator (DSM) is proposed to prevent the potential problems of traditional fractional dividers: the DSM output would be wrongly loaded and the action of DSM circuit may affect the phase-detection of phase-frequency-detector (PFD). Simulation result shows the effectiveness of this improvement.

  7. Agile Development & Software Architecture - Crossing the Great Divide

    Science.gov (United States)

    2016-06-07

    2010 Carnegie Mellon University SEI Webinar Series: Agile Development & Software Architecture – Crossing the Great Divide Software Engineering...2010 4. TITLE AND SUBTITLE Agile Development & Software Architecture - Crossing the Great Divide 5a. CONTRACT NUMBER 5b. GRANT NUMBER 5c. PROGRAM...Mellon University , Software Engineering Institute,Pittsburgh,PA,15213 8. PERFORMING ORGANIZATION REPORT NUMBER 9. SPONSORING/MONITORING AGENCY NAME(S

  8. Grid modeling, analysis and simulation of different scenarios for a smart low-voltage distribution grid

    DEFF Research Database (Denmark)

    Mihet-Popa, Lucian; Han, Xue; Bindner, Henrik W.

    2013-01-01

    , the number of cabinets and customers and the load per customer. The aim of the model is to design, implement and test the proposed configuration and to investigate whether the low-voltage distribution grid is prepared for the expected future increase of PV penetration, heat pumps and electric cars. The model...

  9. Transistorized Marx bank pulse circuit provides voltage multiplication with nanosecond rise-time

    Science.gov (United States)

    Jung, E. A.; Lewis, R. N.

    1968-01-01

    Base-triggered avalanche transistor circuit used in a Marx bank pulser configuration provides voltage multiplication with nanosecond rise-time. The avalanche-mode transistors replace conventional spark gaps in the Marx bank. The delay time from an input signal to the output signal to the output is typically 6 nanoseconds.

  10. An Effective Method for Establishing the Stage and Reflux Requirement of Three-product Dividing Wall Columns

    OpenAIRE

    I. Dejanović; Matijašević, Lj.; Olujić, Ž.

    2011-01-01

    This paper introduces an effective method for determination and optimisation of stage and reflux requirement of a three-product dividing wall column, arranged within a commercial software package by combining a fundamentally sound shortcut method providing reliable initial guesses and a detailed, four-column model, which appeared to be the most flexible among possible configurations, for both steady state and dynamic simulations. The applicability and usability of the method is demonstrate...

  11. Voltage-gated Proton Channels

    Science.gov (United States)

    DeCoursey, Thomas E.

    2014-01-01

    Voltage-gated proton channels, HV1, have vaulted from the realm of the esoteric into the forefront of a central question facing ion channel biophysicists, namely the mechanism by which voltage-dependent gating occurs. This transformation is the result of several factors. Identification of the gene in 2006 revealed that proton channels are homologues of the voltage-sensing domain of most other voltage-gated ion channels. Unique, or at least eccentric, properties of proton channels include dimeric architecture with dual conduction pathways, perfect proton selectivity, a single-channel conductance ~103 smaller than most ion channels, voltage-dependent gating that is strongly modulated by the pH gradient, ΔpH, and potent inhibition by Zn2+ (in many species) but an absence of other potent inhibitors. The recent identification of HV1 in three unicellular marine plankton species has dramatically expanded the phylogenetic family tree. Interest in proton channels in their own right has increased as important physiological roles have been identified in many cells. Proton channels trigger the bioluminescent flash of dinoflagellates, facilitate calcification by coccolithophores, regulate pH-dependent processes in eggs and sperm during fertilization, secrete acid to control the pH of airway fluids, facilitate histamine secretion by basophils, and play a signaling role in facilitating B-cell receptor mediated responses in B lymphocytes. The most elaborate and best-established functions occur in phagocytes, where proton channels optimize the activity of NADPH oxidase, an important producer of reactive oxygen species. Proton efflux mediated by HV1 balances the charge translocated across the membrane by electrons through NADPH oxidase, minimizes changes in cytoplasmic and phagosomal pH, limits osmotic swelling of the phagosome, and provides substrate H+ for the production of H2O2 and HOCl, reactive oxygen species crucial to killing pathogens. PMID:23798303

  12. Characteristics of output voltage and current of integrated nanogenerators

    KAUST Repository

    Yang, Rusen

    2009-01-01

    Owing to the anisotropic property and small output signals of the piezoelectric nanogenerators (NGs) and the influence of the measurement system and environment, identification of the true signal generated by the NG is critical. We have developed three criteria: Schottky behavior test, switching-polarity tests, and linear superposition of current and voltage tests. The 11 tests can effectively rule out the system artifacts, whose sign does not change with the switching measurement polarity, and random signals, which might change signs but cannot consistently add up or cancel out under designed connection configurations. This study establishes the standards for designing and scale up of integrated nanogenerators. © 2009 American Institute of Physics.

  13. Configuring Symantec AntiVirus

    CERN Document Server

    Shimonski, Robert

    2003-01-01

    This is the only book that will teach system administrators how to configure, deploy, and troubleshoot Symantec Enterprise Edition in an enterprise network. The book will reflect Symantec''s philosophy of "Centralized Antivirus Management." For the same reasons that Symantec bundled together these previously separate products, the book will provide system administrators with a holistic approach to defending their networks from malicious viruses. This book will also serve as a Study Guide for those pursuing Symantec Product Specialist Certifications.Configuring Symantec AntiVirus Enterprise Edition contains step-by-step instructions on how to Design, implement and leverage the Symantec Suite of products in the enterprise.ØFirst book published on market leading product and fast-growing certification. Despite the popularity of Symantec''s products and Symantec Product Specialist certifications, there are no other books published or announced.ØLess expensive substitute for costly on-sight training. Symantec off...

  14. Network sensitivity to geographical configuration

    Energy Technology Data Exchange (ETDEWEB)

    Searle, Antony C; Scott, Susan M; McClelland, David E [Department of Physics and Theoretical Physics, Faculty of Science, Australian National University, Canberra, ACT 0200 (Australia)

    2002-04-07

    Gravitational wave astronomy will require the coordinated analysis of data from the global network of gravitational wave observatories. Questions of how to optimally configure the global network arise in this context. We have elsewhere proposed a formalism which is employed here to compare different configurations of the network, using both the coincident network analysis method and the coherent network analysis method. We have constructed a network model to compute a figure-of-merit based on the detection rate for a population of standard-candle binary inspirals. We find that this measure of network quality is very sensitive to the geographic location of component detectors under a coincident network analysis, but comparatively insensitive under a coherent network analysis.

  15. Stereoscopic Configurations To Minimize Distortions

    Science.gov (United States)

    Diner, Daniel B.

    1991-01-01

    Proposed television system provides two stereoscopic displays. Two-camera, two-monitor system used in various camera configurations and with stereoscopic images on monitors magnified to various degrees. Designed to satisfy observer's need to perceive spatial relationships accurately throughout workspace or to perceive them at high resolution in small region of workspace. Potential applications include industrial, medical, and entertainment imaging and monitoring and control of telemanipulators, telerobots, and remotely piloted vehicles.

  16. Drupal 7 Multi Sites Configuration

    CERN Document Server

    Butcher, Matt

    2012-01-01

    Follow the creation of a multi-site instance with Drupal. The practical examples and accompanying screenshots will help you to get multiple Drupal sites set up in no time. This book is for Drupal site builders. It is assumed that readers are familiar with Drupal already, with a basic grasp of its concepts and components. System administration concepts, such as configuring Apache, MySQL, and Vagrant are covered but no previous knowledge of these tools is required.

  17. Microsoft System Center Configuration Manager

    CERN Document Server

    Sandbu, Marius

    2013-01-01

    This book is a step-by-step tutorial that guides you through the key steps in implementing best solutions for high availability and performance tuning. It is split into two distinct approaches: client and site side HA and optimization.Microsoft SCCM High Availability and Performance Tuning is for IT professionals and consultants working with Configuration Manager who wish to learn the skills to deploy a redundant and scalable solution.

  18. Discretized configurations and partial partitions

    CERN Document Server

    Abrams, Aaron; Hower, Valerie

    2010-01-01

    We show that the discretized configuration space of $k$ points in the $n$-simplex is homotopy equivalent to a wedge of spheres of dimension $n-k+1$. This space is homeomorphic to the order complex of the poset of ordered partial partitions of $\\{1,\\...,n+1\\}$ with exactly $k$ parts. We also compute the Euler characteristic in two different ways, thereby obtaining a topological proof of a combinatorial recurrence satisfied by the Stirling numbers of the second kind.

  19. Product Configuration Systems and Productivity

    DEFF Research Database (Denmark)

    Pedersen, Jørgen Lindgaard; Edwards, Kasper

    2004-01-01

    Twelve companies have been interviewed with the purpose to get information about technical, economic and organisational matters in respect of Product Configuration Systems (PCS).Combinations of qualitative interviews and quantitative scoring have been used in ranking expected and realized results...... from implementing PCS. The three highest aggregated scoring expected benefits are: 1)improved quality in specifications, 2)lower turnaround time, 3)less resource intensity....

  20. Power Quality Improvement Using an Enhanced Network-Side-Shunt-Connected Dynamic Voltage Restorer

    Science.gov (United States)

    Fereidouni, Alireza; Masoum, Mohammad A. S.; Moghbel, Moayed

    2015-10-01

    Among the four basic dynamic voltage restorer (DVR) topologies, the network-side shunt-connected DVR (NSSC-DVR) has a relatively poor performance and is investigated in this paper. A new configuration is proposed and implemented for NSSC-DVR to enhance its performance in compensating (un)symmetrical deep and long voltage sags and mitigate voltage harmonics. The enhanced NSSC-DVR model includes a three-phase half-bridge semi-controlled network-side-shunt-connected rectifier and a three-phase full-bridge series-connected inverter implemented with a back-to-back configuration through a bidirectional buck-boost converter. The network-side-shunt-connected rectifier is employed to inject/draw the required energy by NSSC-DVR to restore the load voltage to its pre-fault value under sag/swell conditions. The buck-boost converter is responsible for maintaining the DC-link voltage of the series-connected inverter at its designated value in order to improve the NSSC-DVR capability in compensating deep and long voltage sags/swells. The full-bridge series-connected inverter permits to compensate unbalance voltage sags containing zero-sequence component. The harmonic compensation of the load voltage is achieved by extracting harmonics from the distorted network voltage using an artificial neural network (ANN) method called adaptive linear neuron (Adaline) strategy. Detailed simulations are performed by SIMULINK/MATLAB software for six case studies to verify the highly robustness of the proposed NSSC-DVR model under various conditions.

  1. Phase diagrams and switching of voltage and magnetic field in dilute magnetic semiconductor nanostructures

    Energy Technology Data Exchange (ETDEWEB)

    Escobedo, R. [Departamento de Matematica Aplicada y Ciencias de la Computacion, Universidad de Cantabria, 39005 Santander (Spain); Carretero, M.; Bonilla, L.L. [G. Millan Institute, Fluid Dynamics, Nanoscience and Industrial Maths., Universidad Carlos III de Madrid, 28911 Leganes (Spain); Unidad Asociada al Instituto de Ciencia de Materiales, CSIC, 28049 Cantoblanco, Madrid (Spain); Platero, G. [Instituto de Ciencia de Materiales, CSIC, 28049 Cantoblanco, Madrid (Spain)

    2010-04-15

    The response of an n-doped dc voltage biased II-VI multi-quantum well dilute magnetic semiconductor nanostructure having its first well doped with magnetic (Mn) impurities is analyzed by sweeping wide ranges of both the voltage and the Zeeman level splitting induced by an external magnetic field. The level splitting versus voltage phase diagram shows regions of stable self-sustained current oscillations immersed in a region of stable stationary states. Transitions between stationary states and self-sustained current oscillations are systematically analyzed by both voltage and level splitting abrupt switching. Sudden voltage or/and magnetic field changes may switch on current oscillations from an initial stationary state, and reciprocally, current oscillations may disappear after sudden changes of voltage or/and magnetic field changes into the stable stationary states region. The results show how to design such a device to operate as a spin injector and a spin oscillator by tuning the Zeeman splitting (through the applied external magnetic field), the applied voltage and the sample configuration parameters (doping density, barrier and well widths, etc.) to select the desired stationary or oscillatory behavior. Phase diagram of Zeeman level splitting {delta} vs. dimensionless applied voltage {phi} for N = 10 QWs. White region: stable stationary states; black: stable self-sustained current oscillations. (copyright 2010 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

  2. RINGED ACCRETION DISKS: EQUILIBRIUM CONFIGURATIONS

    Energy Technology Data Exchange (ETDEWEB)

    Pugliese, D.; Stuchlík, Z., E-mail: d.pugliese.physics@gmail.com, E-mail: zdenek.stuchlik@physics.cz [Institute of Physics and Research Centre of Theoretical Physics and Astrophysics, Faculty of Philosophy and Science, Silesian University in Opava, Bezručovo náměstí 13, CZ-74601 Opava (Czech Republic)

    2015-12-15

    We investigate a model of a ringed accretion disk, made up by several rings rotating around a supermassive Kerr black hole attractor. Each toroid of the ringed disk is governed by the general relativity hydrodynamic Boyer condition of equilibrium configurations of rotating perfect fluids. Properties of the tori can then be determined by an appropriately defined effective potential reflecting the background Kerr geometry and the centrifugal effects. The ringed disks could be created in various regimes during the evolution of matter configurations around supermassive black holes. Therefore, both corotating and counterrotating rings have to be considered as being a constituent of the ringed disk. We provide constraints on the model parameters for the existence and stability of various ringed configurations and discuss occurrence of accretion onto the Kerr black hole and possible launching of jets from the ringed disk. We demonstrate that various ringed disks can be characterized by a maximum number of rings. We present also a perturbation analysis based on evolution of the oscillating components of the ringed disk. The dynamics of the unstable phases of the ringed disk evolution seems to be promising in relation to high-energy phenomena demonstrated in active galactic nuclei.

  3. Dynamic configuring of the metastructure

    Directory of Open Access Journals (Sweden)

    Katarzyna Grzybowska

    2012-06-01

    Full Text Available Background: A trend to create groups of enterprises can be observed; whose model of operation makes use of assets of large, small and medium sized companies. It is a higher level of organisational changes. This trend is described as network organisation. It is based on the so called supply chain. The Authors of this paper proposed authors' analysis dynamic configuration of the supply chain and presents an example. The supply chain is a metastructure. It is an intermediate form between a single enterprise (microstructure/microsystem and the global economy (macrostructure/macrosystem. The metastructure is characterized by a dynamic holarchy of mutually cooperating holons (enterprises. Methods: After a brief discussion of the nature of supply chain (metrastructure and configuration of metastructures, authors present variable supply chains in the light of morphological analysis and presents an example.   Results: The key benefits of this approach are: identifying the characteristics of a supply network and modeling the flow in the entire own supply chain metastructure and possible quick adaptations to new situations. Conclusions: Configuration of a supply chain with the use of a morphological analysis is a basic action, if its goal is to optimally model the flow of goods and implementation of quick adaptation to new situations.     

  4. Configuration Management Process Assessment Strategy

    Science.gov (United States)

    Henry, Thad

    2014-01-01

    Purpose: To propose a strategy for assessing the development and effectiveness of configuration management systems within Programs, Projects, and Design Activities performed by technical organizations and their supporting development contractors. Scope: Various entities CM Systems will be assessed dependent on Project Scope (DDT&E), Support Services and Acquisition Agreements. Approach: Model based structured against assessing organizations CM requirements including best practices maturity criteria. The model is tailored to the entity being assessed dependent on their CM system. The assessment approach provides objective feedback to Engineering and Project Management of the observed CM system maturity state versus the ideal state of the configuration management processes and outcomes(system). center dot Identifies strengths and risks versus audit gotcha's (findings/observations). center dot Used "recursively and iteratively" throughout program lifecycle at select points of need. (Typical assessments timing is Post PDR/Post CDR) center dot Ideal state criteria and maturity targets are reviewed with the assessed entity prior to an assessment (Tailoring) and is dependent on the assessed phase of the CM system. center dot Supports exit success criteria for Preliminary and Critical Design Reviews. center dot Gives a comprehensive CM system assessment which ultimately supports configuration verification activities.*

  5. PI and Fuzzy Control Strategies for High Voltage Output DC-DC Boost Power Converter - Hardware Implementation and Analysis

    DEFF Research Database (Denmark)

    Padmanaban, Sanjeevi Kumar; Blaabjerg, Frede; Siano, Pierluigi

    2016-01-01

    converter with inbuilt voltage-lift technique and overcome the aforementioned deficiencies. Further, the control strategy is adapted based on proportional-integral (P-I) and fuzzy logic, closed-loop controller to regulate the outputs and ensure the performances. Complete hardware prototype of EHV converter......This paper presents the control strategies by Proportional-Integral (P-I) and Fuzzy Logic (FL) for a DC-DC boost power converter for high output voltage configuration. Standard DC-DC converters are traditionally used for high voltage direct current (HVDC) power transmission systems. But, lack its...... performances in terms of efficiency, reduced transfer gain and increased cost with sensor units. Moreover, the internal self-parasitic components reduce the output voltage and efficiency of classical high voltage converters (HVC). This investigation focused on extra high-voltage (EHV) DC-DC boost power...

  6. Fast and accurate method for computing ATC with voltage stability

    CERN Document Server

    Eidiani, M; Vahedi, E

    2002-01-01

    Order 889 mandated each control area to computer ATC (Available Transfer Capability) and post them on a communication system called the Open Access Same-time Information System (OASIS). Approaches of computing ATC can be divided into the following groups: Static and Dynamic methods. This paper presents a fast method for ATC calculations with voltage stability termination criteria. We use estimation of the determinant of Jacobian matrix for assessment of voltage stability. This method is compared with these methods: different between energy in SEP (Stable Equilibrium Point) and UEP (Unstable Equilibrium Point), ts index of Dr.Chiang and continuation power flow. The idea are demonstrated on 2, 3, 7 (CIGRE), 10, 30 (IEEE) and 145 bus (Iowa State University).

  7. Neural Correlates of Divided Attention in Natural Scenes.

    Science.gov (United States)

    Fagioli, Sabrina; Macaluso, Emiliano

    2016-09-01

    Individuals are able to split attention between separate locations, but divided spatial attention incurs the additional requirement of monitoring multiple streams of information. Here, we investigated divided attention using photos of natural scenes, where the rapid categorization of familiar objects and prior knowledge about the likely positions of objects in the real world might affect the interplay between these spatial and nonspatial factors. Sixteen participants underwent fMRI during an object detection task. They were presented with scenes containing either a person or a car, located on the left or right side of the photo. Participants monitored either one or both object categories, in one or both visual hemifields. First, we investigated the interplay between spatial and nonspatial attention by comparing conditions of divided attention between categories and/or locations. We then assessed the contribution of top-down processes versus stimulus-driven signals by separately testing the effects of divided attention in target and nontarget trials. The results revealed activation of a bilateral frontoparietal network when dividing attention between the two object categories versus attending to a single category but no main effect of dividing attention between spatial locations. Within this network, the left dorsal premotor cortex and the left intraparietal sulcus were found to combine task- and stimulus-related signals. These regions showed maximal activation when participants monitored two categories at spatially separate locations and the scene included a nontarget object. We conclude that the dorsal frontoparietal cortex integrates top-down and bottom-up signals in the presence of distractors during divided attention in real-world scenes.

  8. Generation of five phase-locked harmonics by implementing a divide-by-three optical frequency divider

    CERN Document Server

    Suhaimi, Nurul Sheeda; Gavara, Trivikramarao; Nakagawa, Ken'ichi; Hong, Feng Lei; Katsuragawa, Masayuki

    2015-01-01

    We report the generation of five phase-locked harmonics, f_1: 2403 nm, f_2: 1201 nm, f_3: 801 nm, f_4: 600 nm, and f_5: 480 nm with an exact frequency ratio of 1 : 2 : 3 : 4 : 5 by implementing a divide-by-three optical-frequency divider in the high harmonic generation process. All five harmonics are generated coaxially with high phase coherence in time and space, which are applicable for various practical uses.

  9. Knowledge Based Product Configuration - a documentatio tool for configuration projects

    DEFF Research Database (Denmark)

    Hvam, Lars; Malis, Martin

    2003-01-01

    How can complex product models be documented in a formalised way that consider both development and maintenance? The need for an effective documentation tool has emerged in order to document the development of product models. The product models have become more and more complex and comprehensive....... A lot of knowledge isput into these systems and many domain experts are involved. This calls for an effective documentation system in order to structure this knowledge in a way that fits to the systems. Standard configuration systems do not support this kind of documentation. The chapter deals...

  10. Tests of Event Filter Configuration Software

    CERN Multimedia

    Wickens, F.J.

    TDAQ - Tests of Event Filter configuration software Within Trigger/DAQ a major consideration is how well the performance of the system components scale in going from the small set-ups used for development work to the final system with many hundreds of processors and links. In the case of the Event Filter, which makes the final stage of on-line event selection, plus on-line calibrations and monitoring, more than a thousand processors are envisaged. These processors will be divided into sub-farms, most will be remote from the detector and some could even be at institutes far from CERN. As part of the on-line system it is important that the software in the sub-farms can be reconfigured rapidly as runs start and stop, and that the system be fault tolerant. The flow of data inside a sub-farm involves many processes, for distribution and collection of results in addition to those for event processing itself. Supervision code written in Java has been developed to manage the processes within a cluster, with XML f...

  11. [Promoting nursing competitiveness: introduction to the digital divide].

    Science.gov (United States)

    Lin, Chun-Hsu; Lee, Ting-Ting

    2010-02-01

    Increasingly sophisticated information technology (IT) has widened the gap (the so-called "digital divide") between those with effective access to IT resources and those without. Problems related to the digital divide exist in every country. In addition to level of familiarity with technology, the divide can also be influenced by factors of race, gender, age, education, economic status and area of residence. The digital divide may be ameliorated through technology innovations in terms of access to information, information application and information literacy. As IT is an increasingly significant component of modern healthcare, it may be expected that the "width" of the potential gap widens as IT applications increase in sophistication. Nursing professionals must keep abreast of advancing technologies in order to narrow the digital divide. To cope with this challenge, nursing professionals should enhance their understanding of new technologies beyond what is taught in formal education curricula. This knowledge enhancement may be attained through self learning or on-the-job training in nursing informatics. Content could cover hospital information system (IS) usage, security, applications and web access. This will improve the ability of nursing staff to face the current IT challenge.

  12. Romania's Digital Divide and the Failures of E-Government

    Directory of Open Access Journals (Sweden)

    Sorin Dan ŞANDOR

    2006-02-01

    Full Text Available This paper tries to measure the level of the digital divide existing in Romania and also to verify its relationship with e-government. At the country level, Romania is one of the least digitally developed countries in Europe, but it has shown a sharp increase in recent years. At the social level, based on data from public opinion surveys, digital divide is analyzed at two levels: lack of access and lack of knowledge. The results are similar to those in other countries: digital divide appears along the same dimensions: rural/urban, age, education, wealth and, to a lesser extent, gender. E-government services, while presumed to be at an adequate level, are used only by a very small number of citizens, thus having no impact upon the digital divide. Confronted with a serious divide, and with great possibility of its increasing, Romania needs to promote policies designed to increase access and knowledge. Also, e-government is not possible, unless administrative culture and procedures change.

  13. Improved Performance and Quality of Configurators by Receiving Real-Time Information from Suppliers

    DEFF Research Database (Denmark)

    Kristjansdottir, Katrin; Shafiee, Sara; Bonev, Martin

    Companies providing customized products are increasingly applying configurators in order to support the sales and design activities. Yet, especially for engineer-to-order (ETO) companies such activities are often divided across different organizations, where throughout the configuration process p...... and maintaining the systems. Furthermore, with the ability of receiving accurate and up-to-date information from suppliers, the quality of the specifications can be improved, which leads to reduced cost of the overall design....

  14. Advances in high voltage engineering

    CERN Document Server

    Haddad, A

    2005-01-01

    This book addresses the very latest research and development issues in high voltage technology and is intended as a reference source for researchers and students in the field, specifically covering developments throughout the past decade. This unique blend of expert authors and comprehensive subject coverage means that this book is ideally suited as a reference source for engineers and academics in the field for years to come.

  15. High Voltage Pulse Testing Survey.

    Science.gov (United States)

    1985-10-01

    Cryogenic 23 E. Liquids 26 F. Solids 28 1. Polyethylene 28 2. Cross-Linked Polyethylene ( XLPE ) 29 3. Polyimide and Polyvenylchloride (PVC) 31 VI Benefits 35 A...Strength of XLPE Cables 29 vii * 4" I PROGRAM OBJECTIVES The Pulse Test Survey summarizes government, industry, and technical reports on high voltage pulse...system of silicone oil on a XLPE (cross-linked polyethylene) spacer tends to lower the impulse breakdown by approximately 10 percent. The negative impulse

  16. TRANSISTOR HIGH VOLTAGE POWER SUPPLY

    Science.gov (United States)

    Driver, G.E.

    1958-07-15

    High voltage, direct current power supplies are described for use with battery powered nuclear detection equipment. The particular advantages of the power supply described, are increased efficiency and reduced size and welght brought about by the use of transistors in the circuit. An important feature resides tn the employment of a pair of transistors in an alternatefiring oscillator circuit having a coupling transformer and other circuit components which are used for interconnecting the various electrodes of the transistors.

  17. Transition State Theory for dissipative systems without a dividing surface

    CERN Document Server

    Revuelta, F; Benito, R M; Borondo, F

    2015-01-01

    Transition State Theory is a central cornerstone in reaction dynamics. Its key step is the identification of a dividing surface that is crossed only once by all reactive trajectories. This assumption is often badly violated, especially when the reactive system is coupled to an environment. The calculations made in this way then overestimate the reaction rate and the results depend critically on the choice of the dividing surface. In this Letter, we study the phase space of a stochastically driven system close to an energetic barrier in order to identify the geometric structure unambiguously determining the reactive trajectories, which is then incorporated in a simple rate formula for reactions in condensed phase that is both independent of the dividing surface and exact.

  18. Bridging the Digital Divide for urban seniors: community partnership.

    Science.gov (United States)

    Cresci, M Kay; Jarosz, Patricia A

    2010-01-01

    Computers and the Internet offer older adults resources for improving health. For many older adults, the "Digital Divide" (the social, economic, and demographic factors that exist between individuals who use computers and those who do not) is a barrier to taking advantage of these resources. Bridging the Digital Divide by making computers and the Internet more accessible and making online health information more usable for older adults has the potential to improve health of older adults. This article describes a strategy for closing the Digital Divide for urban seniors through the formation of a community- university partnership with the goal of improving health and well-being through the use of online health information.

  19. Ouroboros: A Tool for Building Generic, Hybrid, Divide& Conquer Algorithms

    Energy Technology Data Exchange (ETDEWEB)

    Johnson, J R; Foster, I

    2003-05-01

    A hybrid divide and conquer algorithm is one that switches from a divide and conquer to an iterative strategy at a specified problem size. Such algorithms can provide significant performance improvements relative to alternatives that use a single strategy. However, the identification of the optimal problem size at which to switch for a particular algorithm and platform can be challenging. We describe an automated approach to this problem that first conducts experiments to explore the performance space on a particular platform and then uses the resulting performance data to construct an optimal hybrid algorithm on that platform. We implement this technique in a tool, ''Ouroboros'', that automatically constructs a high-performance hybrid algorithm from a set of registered algorithms. We present results obtained with this tool for several classical divide and conquer algorithms, including matrix multiply and sorting, and report speedups of up to six times achieved over non-hybrid algorithms.

  20. Selectively Distracted: Divided Attention and Memory for Important Information.

    Science.gov (United States)

    Middlebrooks, Catherine D; Kerr, Tyson; Castel, Alan D

    2017-08-01

    Distractions and multitasking are generally detrimental to learning and memory. Nevertheless, people often study while listening to music, sitting in noisy coffee shops, or intermittently checking their e-mail. The current experiments examined how distractions and divided attention influence one's ability to selectively remember valuable information. Participants studied lists of words that ranged in value from 1 to 10 points while completing a digit-detection task, while listening to music, or without distractions. Though participants recalled fewer words following digit detection than in the other conditions, there were no significant differences between conditions in terms of selectively remembering the most valuable words. Similar results were obtained across a variety of divided-attention tasks that stressed attention and working memory to different degrees, which suggests that people may compensate for divided-attention costs by selectively attending to the most valuable items and that factors that worsen memory do not necessarily impair the ability to selectively remember important information.

  1. Stopped nucleons in configuration space

    CERN Document Server

    Bialas, Andrzej; Koch, Volker

    2016-01-01

    In this note, using the colour string model, we study the configuration space distribution of stopped nucleons in heavy-ion collisions. We find that the stopped nucleons from the target and the projectile end up separated from each other by the distance increasing with the collision energy. In consequence, for the center of mass energies larger than 6 or 10 GeV (depending on the details of the model) it appears that the system created is not in thermal and chemical equilibrium, and the net baryon density reached is likely not much higher than that already present in the colliding nuclei.

  2. Laser photography system: hardware configuration

    Science.gov (United States)

    Piszczek, Marek; Rutyna, Krzysztof; Kowalski, Marcin; Zyczkowski, Marek

    2012-06-01

    Solution presented in this article is a system using image acquisition time gating method. The time-spatial framing method developed by authors was used to build Laser Photography System (LPS). An active vision system for open space monitoring and terrorist threats detection is being built as an effect of recent work lead in the Institute of Optoelectronics, MUT. The device is destined to prevent and recognize possible terrorist threats in important land and marine areas. The aim of this article is to discuss the properties and hardware configuration of the Laser Photography System.

  3. Electromagnetic configurations of rail guns

    Science.gov (United States)

    Fat'yanov, O. V.; Ostashev, V. E.; Lopyrev, A. N.; Ul'Yanov, A. V.

    1993-06-01

    Some problems associated with the electromagnetic acceleration of macrobodies in a rail gun are examined. An approach to the design of rail gun configurations is proposed, and some basic rail gun schemes are synthesized. The alternative rail gun schemes are compared in terms of electrode potential and stability of the electrode gap with respect to parasitic current shunting. The effect of the ohmic resistance of the electrodes and of the additional magnetization field on the spatial structure of the discharge in the rail gun channel is discussed. A classification of rail gun modifications is presented.

  4. Engineering the Divide-and-Conquer Closest Pair Algorithm

    Institute of Scientific and Technical Information of China (English)

    Ming-hui Jiang; Joel gillespie

    2007-01-01

    We improve the famous divide-and-conquer algorithm by Bentley and Shamos for the planar closest-pair problem. For n points on the plane, our algorithm keeps the optimal O(n log n) time complexity and, using a circle-packing property, computes at most 7n/2 Euclidean distances, which improves Ge et al.'s bound of (3n log n)/2 Euclidean distances. We present experimental results of our comparative studies on four different versions of the divide-and-conquer closest pair algorithm and propose two effective heuristics.

  5. Google and the digital divide the bias of online knowledge

    CERN Document Server

    Segev, Elad

    2010-01-01

    Beneficial to scholars and students in the fields of media and communication, politics and technology, this book outlines the significant role of search engines in general and Google in particular in widening the digital divide between individuals, organisations and states. It uses innovative methods and research approaches to assess and illustrate the digital divide by comparing the popular search queries in Google and Yahoo in different countries as well as analysing the various biases in Google News and Google Earth. The different studies developed and presented in this book provide various

  6. Environmental and biotechnological applications of high-voltage pulsed discharges in water

    Energy Technology Data Exchange (ETDEWEB)

    Sato, Masayuki [Department of Chemical and Environmental Engineering, Gunma University 1-5-1 Tenjin, Kiryu, Gunma 376-8515 (Japan)], E-mail: mxsato@cee.gunma-u.ac.jp

    2008-05-01

    A high-voltage pulse has wide application in fields such as chemistry, physics and biology and their combinations. The high-voltage pulse forms two kinds of physical processes in water, namely (a) a pulsed electric field (PEF) in the parallel electrode configuration and (b) plasma generation by a pulsed discharge in the water phase with a concentrated electric field. The PEF can be used for inactivation of bacteria in liquid foods as a non-thermal process, and the underwater plasma is applicable not only for the decomposition of organic materials in water but also for biological treatment of wastewater. These discharge states are controlled mainly by the applied pulse voltage and the electrode shape. Some examples of environmental and biotechnological applications of a high-voltage pulse are reviewed.

  7. Piezoelectric transformers for low-voltage generation of gas discharges and ionic winds in atmospheric air

    Science.gov (United States)

    Johnson, Michael J.; Go, David B.

    2015-12-01

    To generate a gas discharge (plasma) in atmospheric air requires an electric field that exceeds the breakdown threshold of ˜30 kV/cm. Because of safety, size, or cost constraints, the large applied voltages required to generate such fields are often prohibitive for portable applications. In this work, piezoelectric transformers are used to amplify a low input applied voltage (corona-like discharges on its corners or on adjacent electrodes. In the proper configuration, these discharges can be used to generate a bulk air flow called an ionic wind. In this work, PT-driven discharges are characterized by measuring the discharge current and the velocity of the induced ionic wind with ionic winds generated using input voltages as low as 7 V. The characteristics of the discharge change as the input voltage increases; this modifies the resonance of the system and subsequent required operating parameters.

  8. Piezo Voltage Controlled Planar Hall Effect Devices

    OpenAIRE

    Bao Zhang; Kang-Kang Meng; Mei-Yin Yang; Edmonds, K. W.; Hao Zhang; Kai-Ming Cai; Yu Sheng; Nan Zhang; Yang Ji; Jian-Hua Zhao; Hou-Zhi Zheng; Kai-You Wang

    2015-01-01

    The electrical control of the magnetization switching in ferromagnets is highly desired for future spintronic applications. Here we report on hybrid piezoelectric (PZT)/ferromagnetic (Co2FeAl) devices in which the planar Hall voltage in the ferromagnetic layer is tuned solely by piezo voltages. The change of planar Hall voltage is associated with magnetization switching through 90° in the plane under piezo voltages. Room temperature magnetic NOT and NOR gates are demonstrated based on the pie...

  9. New Supercapacitors of Hybrid Configurations

    Directory of Open Access Journals (Sweden)

    Wako Naoi

    2013-01-01

    Full Text Available In recent years, the improvement of the energydensity of nano-composite battery materials hasbeen object of great study. Hybridizing battery andcapacitor materials overcome the energy densitylimitation of existing generation-I capacitors withoutmuch sacrificing the cycling performances. Normalbattery-capacitor hybrids employ high-energy &sluggish redox electrode and low-energy & fastdouble-layer electrodes, possibly producing a largerworking voltage and higher over-all capacitance. Inorder to smoothly operate such asymmetric systems,however, the rates of the two different electrodes mustbe highly balanced. Especially, the redox rates of thebattery electrodes must be substantially increasedto the levels of double-layer process. In this report,we attempt to identify the essential issues for therealizable hybrids and suggest ways to overcomethe rate enhancement by exemplifying ultrafastperformance of the Li4Ti5O12 nanocrystal preparedvia a unique in-situ material processing technologyunder ultra-centrifuging.

  10. 49 CFR 234.221 - Lamp voltage.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 4 2010-10-01 2010-10-01 false Lamp voltage. 234.221 Section 234.221 Transportation Other Regulations Relating to Transportation (Continued) FEDERAL RAILROAD ADMINISTRATION..., Inspection, and Testing Maintenance Standards § 234.221 Lamp voltage. The voltage at each lamp shall...

  11. Bootstrapped Low-Voltage Analog Switches

    DEFF Research Database (Denmark)

    Steensgaard-Madsen, Jesper

    1999-01-01

    Novel low-voltage constant-impedance analog switch circuits are proposed. The switch element is a single MOSFET, and constant-impedance operation is obtained using simple circuits to adjust the gate and bulk voltages relative to the switched signal. Low-voltage (1-volt) operation is made feasible...

  12. Configurational diffusion of coal macromolecules

    Energy Technology Data Exchange (ETDEWEB)

    Guin, J.A.; Curtis, C.W.; Tarrer, A.R.; Kim, S.; Hwang, D.; Chen, C.C.; Chiou, Z.

    1991-01-01

    The objective of our research was to obtain fundamental information regarding the functional dependence of the diffusion coefficient of coal molecules on the ratio of molecule to pore diameter. That is, the objective of our study was to examine the effect of molecule size and configuration on hindered diffusion of coal macromolecules through as porous medium. To best accomplish this task, we circumvented the complexities of an actual porous catalyst by using a well defined porous matrix with uniform capillaric pores, i.e., a track-etched membrane. In this way, useful information was obtained regarding the relationship of molecular size and configuration on the diffusion rate of coal derived macromolecules through a pore structure with known geometry. Similar studies were performed using a pellet formed of porous alumina, to provide a link between the idealized membranes and the actual complex pore structure of real catalyst extrudates. The fundamental information from our study will be useful toward the tailoring of catalysts to minimize diffusional influences and thereby increase coal conversion and selectivity for desirable products. (VC)

  13. Computational methods for stellerator configurations

    Energy Technology Data Exchange (ETDEWEB)

    Betancourt, O.

    1992-01-01

    This project had two main objectives. The first one was to continue to develop computational methods for the study of three dimensional magnetic confinement configurations. The second one was to collaborate and interact with researchers in the field who can use these techniques to study and design fusion experiments. The first objective has been achieved with the development of the spectral code BETAS and the formulation of a new variational approach for the study of magnetic island formation in a self consistent fashion. The code can compute the correct island width corresponding to the saturated island, a result shown by comparing the computed island with the results of unstable tearing modes in Tokamaks and with experimental results in the IMS Stellarator. In addition to studying three dimensional nonlinear effects in Tokamaks configurations, these self consistent computed island equilibria will be used to study transport effects due to magnetic island formation and to nonlinearly bifurcated equilibria. The second objective was achieved through direct collaboration with Steve Hirshman at Oak Ridge, D. Anderson and R. Talmage at Wisconsin as well as through participation in the Sherwood and APS meetings.

  14. Dark energy stars: Stable configurations

    CERN Document Server

    Bhar, Piyali; Rahaman, Farook; Banerjee, Ayan

    2016-01-01

    In present paper a spherically symmetric stellar configuration has been analyzed by assuming the matter distribution of the stellar configuration is anisotropic in nature and compared with the realistic objects, namely, the low mass X-ray binaries (LMXBs) and X-ray pulsars. The analytic solution has been obtained by utilizing the dark energy equation of state for the interior solution corresponding to the Schwarzschild exterior vacuum solution at the junction interface. Several physical properties like energy conditions, stability, mass-radius ratio, and surface redshift are described through mathematical calculations as well as graphical plots. It is found that obtained mass-radius ration of the compact stars candidates like 4U 1820-30, PSR J 1614-2230, Vela X-1 and Cen X-3 are very much consistent with the observed data by Gangopadhyay et al. (Mon. Not. R. Astron. Soc. 431, 3216 (2013)). So our proposed model would be useful in the investigation of the possible clustering of dark energy.

  15. Tooling system configuration in FMSs

    Energy Technology Data Exchange (ETDEWEB)

    Grieco, A. [Universita degli Studi di Lecce (Italy); Semeraro, Q.; Tolio, T. [Facolta di Ingegneria, Milano (Italy)

    1996-12-31

    The increasing competition has led to product differentiation, life cycle shortening and rapid changes in the demand. One of the possible technological answer to these productive problems is represented by flexible automation and particularly by flexible manufacturing systems, that thanks to their flexibility give the possibility to answer to the variability in the product demand with reduced production costs and with limited flow times. With the advent of computerized manufacturing facilities, in particular FMS, it has become clear that tooling is a major constraint which could potentially prevent these systems from exploiting their full flexibility. Indeed the productivity of a flexible manufacturing system highly depends on the occurrence of conflicts regarding tool usage. This is the reason why tool management has become in the last decade an area of increased research activity. In this paper we present an analytical formulation for the tooling configuration problem in a flexible manufacturing system. The formulation determines the copies number for each tool type in the system minimizing the average lack of time in the machining centers for lack of the necessary tool, under the constraint of an assigned total number of tools. The results of the proposed method have been compared with two models of configuration of the tooling system proposed in literature by means of simulations experiments. The results of the simulations have underlined a meaningful increase of the performance of the system for the proposed model.

  16. Knowledge Based Product Configuration - a documentatio tool for configuration projects

    DEFF Research Database (Denmark)

    Hvam, Lars; Malis, Martin

    2003-01-01

    How can complex product models be documented in a formalised way that consider both development and maintenance? The need for an effective documentation tool has emerged in order to document the development of product models. The product models have become more and more complex and comprehensive....... with the development of a Lotus Notes application that serves as a knowledge based documentation tool for configuration projects. A prototype has been developed and tested empirically in an industrial case-company. It has proved to be a succes.......How can complex product models be documented in a formalised way that consider both development and maintenance? The need for an effective documentation tool has emerged in order to document the development of product models. The product models have become more and more complex and comprehensive...

  17. Evolution of graphene nanoribbons under low-voltage electron irradiation

    KAUST Repository

    Zhu, Wenpeng

    2012-01-01

    Though the all-semiconducting nature of ultrathin graphene nanoribbons (GNRs) has been demonstrated in field-effect transistors operated at room temperature with ∼105 on-off current ratios, the borderline for the potential of GNRs is still untouched. There remains a great challenge in fabricating even thinner GNRs with precise width, known edge configurations and specified crystallographic orientations. Unparalleled to other methods, low-voltage electron irradiation leads to a continuous reduction in width to a sub-nanometer range until the occurrence of structural instability. The underlying mechanisms have been investigated by the molecular dynamics method herein, combined with in situ aberration-corrected transmission electron microscopy and density functional theory calculations. The structural evolution reveals that the zigzag edges are dynamically more stable than the chiral ones. Preferential bond breaking induces atomic rings and dangling bonds as the initial defects. The defects grow, combine and reconstruct to complex edge structures. Dynamic recovery is enhanced by thermal activation, especially in cooperation with electron irradiation. Roughness develops under irradiation and reaches a plateau less than 1 nm for all edge configurations after longtime exposure. These features render low-voltage electron irradiation an attractive technique in the fabrication of ultrathin GNRs for exploring the ultimate electronic properties. © 2012 The Royal Society of Chemistry.

  18. A School Divided: One Elementary School's Response to Education Policy

    Science.gov (United States)

    Zoch, Melody

    2017-01-01

    This article examines how one elementary school was divided into two schools--a primary and an intermediate school--because of how policies were interpreted and enacted with regard to high-stakes testing. The grades in which students took high-stakes tests were privileged in terms of receiving monetary resources and support from staff. An emphasis…

  19. Nigeria united in grief; divided in response: Religious terrorism ...

    African Journals Online (AJOL)

    Nigeria united in grief; divided in response: Religious terrorism, Boko Haram, and the dynamics of state response. ... Boko Haram's avowed aim is to wrest control from the Nigerian government and to impose a strict form of Sharia law across a ...

  20. The Digital Divide and Rural Community Colleges: Problems and Prospects.

    Science.gov (United States)

    Katsinas, Stephen G.; Moeck, Pat

    2002-01-01

    Discusses the seriousness of the digital divide-the discrepancy between technology-literate and -illiterate people-in rural areas in the United States. Reports that rural young, minority, and single-parent households lag behind the national average in both personal computer ownership and Internet access. Offers suggestions for ways rural community…

  1. Fiber-optic Michelson interferometer using an optical power divider.

    Science.gov (United States)

    Imai, M; Ohashi, T; Ohtsuka, Y

    1980-10-01

    A fiber-optic interferometer consisting of a multimode fiber-optical power divider was constructed in the Michelson arrangement and applied to measure a micrometer-order displacement of the vibrating object based on an optical homodyne technique. Improvement in the sensitivity of the apparatus is discussed from the viewpoint of increasing the minimum detectable beat signal.

  2. Response Styles and the Rural-Urban Divide

    Science.gov (United States)

    Thomas, Troy D.; Abts, Koen; Vander Weyden, Patrick

    2014-01-01

    This article investigates the effect of the rural-urban divide on mean response styles (RSs) and their relationships with the sociodemographic characteristics of the respondents. It uses the Representative Indicator Response Style Means and Covariance Structure (RIRSMACS) method and data from Guyana--a developing country in the Caribbean. The…

  3. Leadership Analysis in K-12 Case Study: "Divided Loyalties"

    Science.gov (United States)

    Alsubaie, Merfat Ayesh

    2016-01-01

    This report mainly aims to provide a critical and in-depth analysis of the K-12 Case, "Divided Loyalty" by Holy and Tartar (2004). The case recounts how the manifestation of inadequate leadership skills in a school setting could affect negatively the performance of students.

  4. Dividing Attention Lowers Children's but Increases Adults' False Memories

    Science.gov (United States)

    Otgaar, Henry; Peters, Maarten; Howe, Mark L.

    2012-01-01

    The present study examined the impact of divided attention on children's and adults' neutral and negative true and false memories in a standard Deese/Roediger-McDermott paradigm. Children (7- and 11-year-olds; n = 126) and adults (n = 52) received 5 neutral and 5 negative Deese/Roediger-McDermott word lists; half of each group also received a…

  5. From Fundamentalists to Structuralists: Bridging the Digital Divide

    Science.gov (United States)

    Kok, Ayse

    2010-01-01

    The purpose of this literature review is to provide information about several ICT initiatives undertaken in education on a global basis in order to overcome the digital divide and summarise the findings of these initiatives. Due to the limited scope of the study, the bulk of the review mainly concerns initiatives undertaken in secondary schools,…

  6. The Digital Divide and Its Impact on Academic Performance

    Science.gov (United States)

    Sun, Jerry Chih-Yuan; Metros, Susan E.

    2011-01-01

    The purpose of this article is to explore issues of the digital divide and its impact on academic performance. Research shows that proper use of technology by students increases their academic performance outcomes. In the literature review section, the authors review articles and theories based on Bennett's (2001) societal equity framework. The…

  7. Journalism Students, Web 2.0 and the Digital Divide

    Science.gov (United States)

    Green, Mary Elizabeth

    2009-01-01

    The purpose of this study was to find out if students were utilizing Web 2.0 applications. Since the applications in question are often employed by the media industry, the study aspired to find out if students majoring in mass communication and journalism utilized the applications more often than other students. The "digital divide" is a term used…

  8. The Digital Divide: The Special Case of Gender

    Science.gov (United States)

    Cooper, J.

    2006-01-01

    This paper examines the evidence for the digital divide based on gender. An overview of research published in the last 20 years draws to the conclusion that females are at a disadvantage relative to men when learning about computers or learning other material with the aid of computer-assisted software. The evidence shows that the digital divide…

  9. Peculiarities of the Digital Divide in Sub-Saharan Africa

    Science.gov (United States)

    Mutula, Stephen M.

    2005-01-01

    Purpose: Seeks to argue that the peculiarities of sub-Saharan Africa, in terms of its socio-cultural diversity, low economic development, linguistic factors, HIV/AIDS pandemic, gender discrimination, low ICT awareness and so on, demand a new model of addressing the digital divide. Design/methodology/approach: Paper largely based on literature…

  10. Digital Divide among Youth: Socio-Cultural Factors and Implications

    Science.gov (United States)

    Parycek, Peter; Sachs, Michael; Schossbock, Judith

    2011-01-01

    Purpose: This paper aims to examine socio-cultural differences in internet use (Digital Divide) among 14-year-old Austrian pupils, in particular usage scenarios and research competences. It is based on a paper presented at the International Association for the Development of the Information Society e-Society conference, 10-13 March 2011, Spain…

  11. Effects of valence and divided attention on cognitive reappraisal processes.

    Science.gov (United States)

    Morris, John A; Leclerc, Christina M; Kensinger, Elizabeth A

    2014-12-01

    Numerous studies have investigated the neural substrates supporting cognitive reappraisal, identifying the importance of cognitive control processes implemented by prefrontal cortex (PFC). This study examined how valence and attention affect the processes used for cognitive reappraisal by asking participants to passively view or to cognitively reappraise positive and negative images with full or divided attention. When participants simply viewed these images, results revealed few effects of valence or attention. However, when participants engaged in reappraisal, there was a robust effect of valence, with the reappraisal of negative relative to positive images associated with more widespread activation, including within regions of medial and lateral PFC. There also was an effect of attention, with more lateral PFC recruitment when regulating with full attention and more medial PFC recruitment when regulating with divided attention. Within two regions of medial PFC and one region of ventrolateral PFC, there was an interaction between valence and attention: in these regions, divided attention reduced activity during reappraisal of positive but not negative images. Critically, participants continued to report reappraisal success even during the Divided Attention condition. These results suggest multiple routes to successful cognitive reappraisal, depending upon image valence and the availability of attentional resources.

  12. A School Divided: One Elementary School's Response to Education Policy

    Science.gov (United States)

    Zoch, Melody

    2017-01-01

    This article examines how one elementary school was divided into two schools--a primary and an intermediate school--because of how policies were interpreted and enacted with regard to high-stakes testing. The grades in which students took high-stakes tests were privileged in terms of receiving monetary resources and support from staff. An emphasis…

  13. Theories of Learning in Educational Development: Relocating the Paradigmatic Divide.

    Science.gov (United States)

    Inglis, Alistair

    1996-01-01

    Offers a critique of a previous discussion on instructional industrialism in distance education based on instructional design. Topics include the psychological foundations of instructional design, competing paradigms in educational development, behaviorism and cognitivism, theories of learning and the paradigmatic divide, and implications for…

  14. Journalism Students, Web 2.0 and the Digital Divide

    Science.gov (United States)

    Green, Mary Elizabeth

    2009-01-01

    The purpose of this study was to find out if students were utilizing Web 2.0 applications. Since the applications in question are often employed by the media industry, the study aspired to find out if students majoring in mass communication and journalism utilized the applications more often than other students. The "digital divide" is a term used…

  15. Tamil Nadu and the Diagonal Divide in Sex Ratios

    NARCIS (Netherlands)

    A.S. Bedi (Arjun Singh); S. Srinivasan (Sharada)

    2009-01-01

    textabstractBetween 1961 and 2001, India’s 0-6 sex ratio has steadily declined. Despite evidence to the contrary, this ratio is often characterised in terms of a diagonal divide with low 0-6 sex ratios in northern and western India and normal 0-6 sex ratios in eastern and southern India. While unexp

  16. Theories of Learning in Educational Development: Relocating the Paradigmatic Divide.

    Science.gov (United States)

    Inglis, Alistair

    1996-01-01

    Offers a critique of a previous discussion on instructional industrialism in distance education based on instructional design. Topics include the psychological foundations of instructional design, competing paradigms in educational development, behaviorism and cognitivism, theories of learning and the paradigmatic divide, and implications for…

  17. Using Bloom To Bridge the WAC/WID Divide.

    Science.gov (United States)

    Cross, Geoffrey; Wills, Katherine

    A longitudinal study combined Stephen Tsuchdi's Workaday activities with Bloom's taxonomy of educational objectives to bridge the WAC/WID (writing across the curriculum/writing in the disciplines) divide. The researchers hoped that by combining concrete activities that can be applied across disciplines with a Bloomian conceptual framework of…

  18. DVCCs Based High Input Impedance Voltage-Mode First-Order Filters Employing Grounded Capacitor and Resistor

    Directory of Open Access Journals (Sweden)

    J. W. Horng

    2010-12-01

    Full Text Available A voltage-mode high input impedance first-order highpass, lowpass and allpass filters using two differential voltage current conveyors (DVCCs, one grounded capacitor and one grounded resistor is presented. The highpass, lowpass and allpass signals can be obtained simultaneously from the circuit configuration. The suggested filter uses a canonical number of passive components without requiring any component matching condition. The simulation results confirm the theoretical analysis.

  19. Effect of four factors in the calculation of induced voltages on a tree-shaped distribution line

    Energy Technology Data Exchange (ETDEWEB)

    Torres, Horacio; Perez, Ernesto; Herrera, Javier; Younes, Camilo; Salgado, Milton; Quintana, Carlos; Rondon, Daniel; Gallego, Luis; Montana, Johny; Vargas, Mauricio [Universidad Nacional de Colombia, Bogota (Colombia). Research Program on Acquisition and Analysis of Signals - PAAS]. E-mail: paas@paas.unal.edu.co

    2001-07-01

    The main objective of this paper is to show a sensibility analysis of four different factors: current waveform, return stroke velocity, lightning current amplitude and network configuration in the calculation of induced voltages on a tree-shaped distribution line. In order to calculate distribution line. In order to calculate the induced voltages it was used the EMTP/ATP program with the inclusion of Rusck's Coupling Model into the MODELS routine. (author)

  20. The configuration category of a product

    OpenAIRE

    de Brito, Pedro Boavida; Weiss, Michael S.

    2017-01-01

    A construction related to the Boardman-Vogt tensor product of operads allows us to describe the configuration category of a product manifold $M\\times N$ in terms of the configuration categories of the factors $M$ and $N$.

  1. Advanced on-chip divider for monolithic microwave VCO's

    Science.gov (United States)

    Peterson, Weddell C.

    1989-01-01

    High frequency division on a monolithic circuit is a critical technology required to significantly enhance the performance of microwave and millimeter-wave phase-locked sources. The approach used to meet this need is to apply circuit design practices which are essentially 'microwave' in nature to the basically 'digital' problem of high speed division. Following investigation of several promising circuit approaches, program phase 1 culminated in the design and layout of an 8.5 GHz (Deep Space Channel 14) divide by four circuit based on a dynamic mixing divider circuit approach. Therefore, during program phase 2, an 8.5 GHz VCO with an integral divider which provides a phase coherent 2.125 GHz reference signal for phase locking applications was fabricated and optimized. Complete phase locked operation of the monolithic GaAs devices (VCO, power splitter, and dynamic divider) was demonstrated both individually and as an integrated unit. The fully functional integrated unit in a suitable test fixture was delivered to NASA for engineering data correlation. Based on the experience gained from this 8.5 GHz super component, a monolithic GaAs millimeter-wave dynamic divider for operation with an external VCO was also designed, fabricated, and characterized. This circuit, which was also delivered to NASA, demonstrated coherent division by four at an input frequency of 24.3 GHz. The high performance monolithic microwave VCO with a coherent low frequency reference output described in this report and others based on this technology will greatly benefit advanced communications systems in both the DoD and commercial sectors. Signal processing and instrumentation systems based on phase-locking loops will also attain enhanced performance at potentially reduced cost.

  2. Advanced on-chip divider for monolithic microwave VCO's

    Science.gov (United States)

    Peterson, Weddell C.

    1989-05-01

    High frequency division on a monolithic circuit is a critical technology required to significantly enhance the performance of microwave and millimeter-wave phase-locked sources. The approach used to meet this need is to apply circuit design practices which are essentially 'microwave' in nature to the basically 'digital' problem of high speed division. Following investigation of several promising circuit approaches, program phase 1 culminated in the design and layout of an 8.5 GHz (Deep Space Channel 14) divide by four circuit based on a dynamic mixing divider circuit approach. Therefore, during program phase 2, an 8.5 GHz VCO with an integral divider which provides a phase coherent 2.125 GHz reference signal for phase locking applications was fabricated and optimized. Complete phase locked operation of the monolithic GaAs devices (VCO, power splitter, and dynamic divider) was demonstrated both individually and as an integrated unit. The fully functional integrated unit in a suitable test fixture was delivered to NASA for engineering data correlation. Based on the experience gained from this 8.5 GHz super component, a monolithic GaAs millimeter-wave dynamic divider for operation with an external VCO was also designed, fabricated, and characterized. This circuit, which was also delivered to NASA, demonstrated coherent division by four at an input frequency of 24.3 GHz. The high performance monolithic microwave VCO with a coherent low frequency reference output described in this report and others based on this technology will greatly benefit advanced communications systems in both the DoD and commercial sectors. Signal processing and instrumentation systems based on phase-locking loops will also attain enhanced performance at potentially reduced cost.

  3. Voltage Management in Unbalanced Low Voltage Networks Using a Decoupled Phase-Tap-Changer Transformer

    DEFF Research Database (Denmark)

    Coppo, Massimiliano; Turri, Roberto; Marinelli, Mattia

    2014-01-01

    The paper studies a medium voltage-low voltage transformer with a decoupled on load tap changer capability on each phase. The overall objective is the evaluation of the potential benefits on a low voltage network of such possibility. A realistic Danish low voltage network is used for the analysis...

  4. Estimating Voltage Asymmetry Making by One Phase Micro-generator in Low Voltage Network

    Directory of Open Access Journals (Sweden)

    Marian Sobierajski

    2014-12-01

    Full Text Available Connection of one phase micro-generator to the low voltage network increases voltage asymmetry. The voltage asymmetry is defined as the quotient of negative and positive voltage components. The mathematical background of exact and rough computation of the asymmetry quotient is presented in the paper. Considerations are illustrated by simple examples.

  5. 76 FR 70721 - Voltage Coordination on High Voltage Grids; Notice of Staff Workshop

    Science.gov (United States)

    2011-11-15

    ... Energy Regulatory Commission Voltage Coordination on High Voltage Grids; Notice of Staff Workshop Take notice that the Federal Energy Regulatory Commission will hold a Workshop on Voltage Coordination on High Voltage Grids on Thursday, December 1, 2011 from 9 a.m. to 4:30 p.m. This staff-led workshop will be...

  6. Piezoelectric transformers for low-voltage generation of gas discharges and ionic winds in atmospheric air

    Energy Technology Data Exchange (ETDEWEB)

    Johnson, Michael J. [Department of Aerospace and Mechanical Engineering, University of Notre Dame, Notre Dame, Indianapolis 46556 (United States); Go, David B., E-mail: dgo@nd.edu [Department of Aerospace and Mechanical Engineering, University of Notre Dame, Notre Dame, Indianapolis 46556 (United States); Department of Chemical and Biomolecular Engineering, University of Notre Dame, Notre Dame, Indianapolis 46556 (United States)

    2015-12-28

    To generate a gas discharge (plasma) in atmospheric air requires an electric field that exceeds the breakdown threshold of ∼30 kV/cm. Because of safety, size, or cost constraints, the large applied voltages required to generate such fields are often prohibitive for portable applications. In this work, piezoelectric transformers are used to amplify a low input applied voltage (<30 V) to generate breakdown in air without the need for conventional high-voltage electrical equipment. Piezoelectric transformers (PTs) use their inherent electromechanical resonance to produce a voltage amplification, such that the surface of the piezoelectric exhibits a large surface voltage that can generate corona-like discharges on its corners or on adjacent electrodes. In the proper configuration, these discharges can be used to generate a bulk air flow called an ionic wind. In this work, PT-driven discharges are characterized by measuring the discharge current and the velocity of the induced ionic wind with ionic winds generated using input voltages as low as 7 V. The characteristics of the discharge change as the input voltage increases; this modifies the resonance of the system and subsequent required operating parameters.

  7. An Embedded Voltage Harmonic Compensation Strategy for Current Controlled DG Interfacing Converters

    DEFF Research Database (Denmark)

    Zhao, Xin; Meng, Lexuan; Guerrero, Josep M.

    2016-01-01

    Harmonics have been considered as one of the major issues in future power grids. With the increasing demand in advanced control functions, power electronic converter interfaced Distributed Generators (DGs) are expected to perform harmonic compensation when necessary. It has been demonstrated in a...... voltage detection; 3) compared with conventional voltage detection based method, it offers better performance because of direct harmonic voltage regulation. Experimental results are presented to demonstrate the effectiveness of the method....... in a number of studies that DG converters operating in Voltage-Controlled Mode (VCM) can be easily configured to realize voltage harmonic suppression utilizing naturally embedded voltage control loop. While for DG converters operating in Current-Controlled Mode (CCM), such function was rarely studied....... Considering that CCM is commonly used in renewable energy based generators and energy storage systems, it has certain significance to achieve the same function with CCM operated converters. Aiming at such objective, this paper proposes a voltage detection based embedded Harmonic Compensator (HC) for CCM...

  8. The Series Connected Buck Boost Regulator Concept for High Efficiency Light Weight DC Voltage Regulation

    Science.gov (United States)

    Birchenough, Arthur G.

    2003-01-01

    Improvements in the efficiency and size of DC-DC converters have resulted from advances in components, primarily semiconductors, and improved topologies. One topology, which has shown very high potential in limited applications, is the Series Connected Boost Unit (SCBU), wherein a small DC-DC converter output is connected in series with the input bus to provide an output voltage equal to or greater than the input voltage. Since the DC-DC converter switches only a fraction of the power throughput, the overall system efficiency is very high. But this technique is limited to applications where the output is always greater than the input. The Series Connected Buck Boost Regulator (SCBBR) concept extends partial power processing technique used in the SCBU to operation when the desired output voltage is higher or lower than the input voltage, and the implementation described can even operate as a conventional buck converter to operate at very low output to input voltage ratios. This paper describes the operation and performance of an SCBBR configured as a bus voltage regulator providing 50 percent voltage regulation range, bus switching, and overload limiting, operating above 98 percent efficiency. The technique does not provide input-output isolation.

  9. Design of low-voltage bipolar operational amplifiers

    Science.gov (United States)

    Fonderie, Jeroen

    The design of input stages for low voltage Operational Amplifiers (OpAmps) is considered. The purpose of this design emanates from the objective of having a common mode input voltage range that reaches from one supply rail to the other, and designs that have this feature both at a 2 V and at a 1 V supply are discussed. Possible output stage configurations are analyzed. This discussion is restricted to output stages that have an output voltage range that also reaches from rail to rail. Further, the output stage should be able to supply a sufficiently large output current to the load that is externally connected to the OpAmp. The frequency response of the output stage is the focus of the discussion. The circuit parts that remain to complete the design of the OpAmp are discussed. These circuit parts are the intermediate stage, inserted between the input and output stage to boost the overall gain of the OpAmp, some implementations of the class AB current control circuit, circuitry to protect the output transistor from heavy saturation and from excessive power consumption, and, finally, the proportional to absolute temperature reference current generator. A detailed analysis of the frequency compensation techniques that can be used to stabilize the OpAmp is given. From this theory, design criteria to successfully implement the compensation method are derived. The experimental OpAmp designs and the measurements performed on these designs are described. Conclusions and suggestions for further research are given.

  10. Improving transition voltage spectroscopy of molecular junctions

    DEFF Research Database (Denmark)

    Markussen, Troels; Chen, Jingzhe; Thygesen, Kristian Sommer

    2011-01-01

    Transition voltage spectroscopy (TVS) is a promising spectroscopic tool for molecular junctions. The principles in TVS is to find the minimum on a Fowler-Nordheim plot where ln(I/V2) is plotted against 1/V and relate the voltage at the minimum Vmin to the closest molecular level. Importantly, Vmin...... is approximately half the voltage required to see a peak in the dI/dV curve. Information about the molecular level position can thus be obtained at relatively low voltages. In this work we show that the molecular level position can be determined at even lower voltages, Vmin(α), by finding the minimum of ln...

  11. Piezo Voltage Controlled Planar Hall Effect Devices

    Science.gov (United States)

    Zhang, Bao; Meng, Kang-Kang; Yang, Mei-Yin; Edmonds, K. W.; Zhang, Hao; Cai, Kai-Ming; Sheng, Yu; Zhang, Nan; Ji, Yang; Zhao, Jian-Hua; Zheng, Hou-Zhi; Wang, Kai-You

    2016-06-01

    The electrical control of the magnetization switching in ferromagnets is highly desired for future spintronic applications. Here we report on hybrid piezoelectric (PZT)/ferromagnetic (Co2FeAl) devices in which the planar Hall voltage in the ferromagnetic layer is tuned solely by piezo voltages. The change of planar Hall voltage is associated with magnetization switching through 90° in the plane under piezo voltages. Room temperature magnetic NOT and NOR gates are demonstrated based on the piezo voltage controlled Co2FeAl planar Hall effect devices without the external magnetic field. Our demonstration may lead to the realization of both information storage and processing using ferromagnetic materials.

  12. Piezo Voltage Controlled Planar Hall Effect Devices.

    Science.gov (United States)

    Zhang, Bao; Meng, Kang-Kang; Yang, Mei-Yin; Edmonds, K W; Zhang, Hao; Cai, Kai-Ming; Sheng, Yu; Zhang, Nan; Ji, Yang; Zhao, Jian-Hua; Zheng, Hou-Zhi; Wang, Kai-You

    2016-06-22

    The electrical control of the magnetization switching in ferromagnets is highly desired for future spintronic applications. Here we report on hybrid piezoelectric (PZT)/ferromagnetic (Co2FeAl) devices in which the planar Hall voltage in the ferromagnetic layer is tuned solely by piezo voltages. The change of planar Hall voltage is associated with magnetization switching through 90° in the plane under piezo voltages. Room temperature magnetic NOT and NOR gates are demonstrated based on the piezo voltage controlled Co2FeAl planar Hall effect devices without the external magnetic field. Our demonstration may lead to the realization of both information storage and processing using ferromagnetic materials.

  13. Assessment value of ECG Cornell voltage for left ventricle hypertrophy in essential hypertension patients and its correlation with cardiovascular events

    Institute of Scientific and Technical Information of China (English)

    Hua-Qin Hu; Mei Zhang; Qian Yang

    2016-01-01

    Objective:To analyze the assessment value of ECG Cornell voltage for left ventricle hypertrophy in essential hypertension patients and its correlation with cardiovascular events. Methods:A total of 118 cases of patients with essential hypertension who received inpatients treatment in our hospital from March 2013 to March 2015 were selected as the research subjects. According to ECG baseline, all included patients were divided into Cornell voltage increase group (increase ≥25%) 47 cases, no Cornell voltage change group (change < 25%) 36 cases and Cornell voltage decrease group (decrease ≥25%) 35 cases. Ultrasonic left heart indexes and serum indexes of three groups were compared, and the correlation between Cornell voltage and cardiovascular events was further analyzed.Results: Ultrasonic LVEDD, LVMI, IVSd, PWd and RWT values as well as serum uric acid, IMD, CysC, FGF23 and Hcy values of Cornell voltage decrease group were lower than those of no Cornell voltage change group and Cornell voltage increase group; ECG Cornell voltage levels in patients with essential hypertension were positively correlated with the incidence rate of cardiovascular events such as acute coronary events, sudden cardiac death and acute stroke.Conclusion: ECG Cornell voltage index can better identify the degree of left ventricle hypertrophy in patients with essential hypertension, and can be used as an independent predictor of cardiovascular events.

  14. Capacitor Voltages Measurement and Balancing in Flying Capacitor Multilevel Converters Utilizing a Single Voltage Sensor

    DEFF Research Database (Denmark)

    Farivar, Glen; Ghias, Amer M. Y. M.; Hredzak, Branislav

    2017-01-01

    This paper proposes a new method for measuring capacitor voltages in multilevel flying capacitor (FC) converters that requires only one voltage sensor per phase leg. Multiple dc voltage sensors traditionally used to measure the capacitor voltages are replaced with a single voltage sensor at the ac...... side of the phase leg. The proposed method is subsequently used to balance the capacitor voltages using only the measured ac voltage. The operation of the proposed measurement and balancing method is independent of the number of the converter levels. Experimental results presented for a five-level FC...

  15. Study on Optimization Strategy for Voltage and Reactive Power Control of Wind Farm

    Science.gov (United States)

    Lu, Q.; Shi, L.; Chen, N.

    A method for calculating reactive power limit of wind farm comprised of doubly-fed induction generators (DFIG) is proposed. The reactive power limit of wind farm is the sum of reactive power limit of DFIGs which is calculated by the method considering static stability margin. Based on this, reactive power control of wind farm is discussed and proposed. The proposed reactive power control is divided into different control modes according to power factor of high voltage side in wind farm substation and voltage of low voltage side in point of interconnection(POI). In different control modes, different control objects are applied on reactive power regulation. After reactive power regulation is finished, some reactive power of wind farm should be released. At last, numerical test system is established, the result shows that the proposed method is effective to support voltage of POI

  16. Interactive Cost Configuration Over Decision Diagrams

    DEFF Research Database (Denmark)

    Andersen, Henrik Reif; Hadzic, Tarik; Pisinger, David

    2010-01-01

    then discuss interactive configuration in the presence of multiple cost functions. We prove that even in its simplest form, multiple-cost configuration is NP-hard in the input MDD. However, for solving two-cost configuration we develop a pseudo-polynomial scheme and a fully polynomial approximation scheme...

  17. Interactive Cost Configuration Over Decision Diagrams

    DEFF Research Database (Denmark)

    Andersen, Henrik Reif; Hadzic, Tarik; Pisinger, David

    2010-01-01

    then discuss interactive configuration in the presence of multiple cost functions. We prove that even in its simplest form, multiple-cost configuration is NP-hard in the input MDD. However, for solving two-cost configuration we develop a pseudo-polynomial scheme and a fully polynomial approximation scheme...

  18. Offshore Vendors’ Software Development Team Configurations

    DEFF Research Database (Denmark)

    Chakraborty, Suranjan; Sarker, Saonee; Rai, Sudhanshu

    2012-01-01

    This research uses configuration theory and data collected from a major IT vendor organization to examine primary configurations of distributed teams in a global off-shoring context. The study indicates that off-shoring vendor organizations typically deploy three different types of configurations...

  19. Voltage-Sensitive Load Controllers for Voltage Regulation and Increased Load Factor in Distribution Systems

    DEFF Research Database (Denmark)

    Douglass, Philip James; Garcia-Valle, Rodrigo; Østergaard, Jacob

    2014-01-01

    consumption which can be mapped to temperature setpoint offsets of thermostat controlled loads. In networks where a lower voltage level corresponds to high system load (and vice versa), this controller acts to regulate voltage and increase the load factor. Simulations are conducted on low- and medium-voltage......This paper presents a novel controller design for controlling appliances based on local measurements of voltage. The controller finds the normalized voltage deviation accounting for the sensitivity of voltage measurements to appliance state. The controller produces a signal indicating desired power...... distribution systems with residential loads including voltage-sensitive water heaters. In low-voltage systems, the results of the simulations show the controller to be effective at reducing the extremes of voltage and increasing the load factor while respecting end-use temperature constraints. In medium-voltage...

  20. Book review of Cristian Nünlist and David Svarin (eds.) Overcoming the East-West Divide: Perspectives on the Role of the OSCE in the Ukraine Crisis

    NARCIS (Netherlands)

    Kraft van Ermel, Nicolaas

    2014-01-01

    In 2014 Europe’s security configuration had to deal with a severe crisis. Events in Ukraine led to a situation of civil war in Ukraine and a further development of the East-West Divide between (Western) Europe and Russia. During 2014 most attention was given to international actors like the North At

  1. Voltage-controlled photonic oscillator.

    Science.gov (United States)

    Savchenkov, A A; Ilchenko, V S; Liang, W; Eliyahu, D; Matsko, A B; Seidel, D; Maleki, L

    2010-05-15

    We report the development and demonstration of an X-band voltage-controlled photonic oscillator based on a whispering gallery mode resonator made of an electro-optic crystalline material. The oscillator has good spectral purity and wide, agile, linear tunability. We have modified the existing theoretical model of the opto-electronic oscillator to describe the performance of our tunable oscillator and have found a good agreement between the theoretical predictions and the measurement results. We show that the device is promising for higher-frequency applications where high-performance tunable oscillators with wide tunability do not exist.

  2. Knowledge Engineering for Embedded Configuration

    DEFF Research Database (Denmark)

    Oddsson, Gudmundur Valur

    2008-01-01

    . Simplifications of the internal workings are both due to hardware- and application-induced configuration taking place both within the overall system and in each subsystem. By relating parameters in such a way, the number of user inputs or decision variables should decrease drastically, thus increasing the overall......, and predefined relation types are suggested. The models are stringent and thought out so they can be implemented in software. They should allow both import and export of product knowledge from the knowledge-based system. The purpose of this work is to simplify the installation process of product systems...... that have been treated with extreme postponement, meaning that variance is given with variables while installing. Variables here can be both software- and hardware-like in nature. These variables are defined as decision variables, and it is the reduction of these variables that is the overall goal. The next...

  3. Code Organization and Configuration Management

    Institute of Scientific and Technical Information of China (English)

    J.P.Wellisch; I.Osborne; 等

    2001-01-01

    Industry experts are increasingly focusing on team productivity on team productivity as the key to success,the base of the team effort is the four-fold structure of software in terms of logical organisation,physical organisation,managerial organisation,and dynamical structure.We describe the ideas put into action within the CMS software for organising software into sub-systems and packages,and to establish configuration management in a multiproject environment.We use a structure that allows to maximise the independence of soft ware development in individual areas,and at the same time emphasises the overwhelming importance of the interdependencies between the packages and components in the system.We comment on release procedures,and describe the inter-relationship between release,development,integration,and testing.

  4. Voltage Management in Unbalanced Low Voltage Networks Using a Decoupled Phase-Tap-Changer Transformer

    OpenAIRE

    Coppo, Massimiliano; Turri, Roberto; Marinelli, Mattia; Han, Xue

    2014-01-01

    The paper studies a medium voltage-low voltage transformer with a decoupled on load tap changer capability on each phase. The overall objective is the evaluation of the potential benefits on a low voltage network of such possibility. A realistic Danish low voltage network is used for the analysis. The load profiles are characterized by using single phase measurement data on voltages, currents and active powers with a 10 minutes resolution. Different scenarios are considered: no tap action, th...

  5. Near-Threshold Computing and Minimum Supply Voltage of Single-Rail MCML Circuits

    Directory of Open Access Journals (Sweden)

    Ruiping Cao

    2014-01-01

    Full Text Available In high-speed applications, MOS current mode logic (MCML is a good alternative. Scaling down supply voltage of the MCML circuits can achieve low power-delay product (PDP. However, the current almost all MCML circuits are realized with dual-rail scheme, where the NMOS configuration in series limits the minimum supply voltage. In this paper, single-rail MCML (SRMCML circuits are described, which can avoid the devices configuration in series, since their logic evaluation block can be realized by only using MOS devices in parallel. The relationship between the minimum supply voltage of the SRMCML circuits and the model parameters of MOS transistors is derived, so that the minimum supply voltage can be estimated before circuit designs. An MCML dynamic flop-flop based on SRMCML is also proposed. The optimization algorithm for near-threshold sequential circuits is presented. A near-threshold SRMCML mode-10 counter based on the optimization algorithm is verified. Scaling down the supply voltage of the SRMCML circuits is also investigated. The power dissipation, delay, and power-delay products of these circuits are carried out. The results show that the near-threshold SRMCML circuits can obtain low delay and small power-delay product.

  6. A new low voltage level-shifted FVF current mirror with enhanced bandwidth and output resistance

    Science.gov (United States)

    Aggarwal, Bhawna; Gupta, Maneesha; Gupta, Anil Kumar; Sangal, Ankur

    2016-10-01

    This paper proposes a new high-performance level-shifted flipped voltage follower (LSFVF) based low-voltage current mirror (CM). The proposed CM utilises the low-supply voltage and low-input resistance characteristics of a flipped voltage follower (FVF) CM. In the proposed CM, level-shifting configuration is used to obtain a wide operating current range and resistive compensation technique is employed to increase the operating bandwidth. The peaking in frequency response is reduced by using an additional large MOSFET. Moreover, a very high output resistance (in GΩ range) along with low-current transfer error is achieved through super-cascode configuration for a wide current range (0-440 µA). Small signal analysis is carried out to show the improvements achieved at each step. The proposed CM is simulated by Mentor Graphics Eldospice in TSMC 0.18 µm CMOS, BSIM3 and Level 53 technology. In the proposed CM, a bandwidth of 6.1799 GHz, 1% settling time of 0.719 ns, input and output resistances of 21.43 Ω and 1.14 GΩ, respectively, are obtained with a single supply voltage of 1 V. The layout of the proposed CM has been designed and post-layout simulation results have been shown. The post-layout simulation results for Monte Carlo and temperature analysis have also been included to show the reliability of the CM against the variations in process parameters and temperature changes.

  7. Crossing of the phantom divide in modified gravity

    CERN Document Server

    Bamba, Kazuharu; Nojiri, Shin'ichi; Odintsov, Sergei D

    2009-01-01

    We reconstruct an explicit model of modified gravity in which a crossing of the phantom divide can be realized. It is shown that the Big Rip singularity appears in the model of modified gravity, whereas that the (finite-time) Big Rip singularity in modified gravity is transformed to the infinite-time singularity in the corresponding scalar field theory obtained through the conformal transformation. Furthermore, we investigate the relations between the scalar field theories realizing a crossing of the phantom divide and the corresponding modified gravitational theories by using the inverse conformal transformation. It is demonstrated that the scalar field theories describing the non-phantom phase (phantom one with the Big Rip) can be represented as the theories of real (complex) $F(R)$ gravity through the inverse (complex) conformal transformation. We also study a viable model of modified gravity in which the transition from the de Sitter universe to the phantom phase can occur.

  8. SIW based multilayer transition and power divider in LTCC technology

    KAUST Repository

    Abuzaid, Hattan

    2013-06-01

    A multilayer transition and balanced power divider are presented for millimeter-wave system-on-package (SoP). These two components operate at Ka-band and exploit the substrate integrate waveguide (SIW) technology with its shielding characteristics and the Low-temperature co-fired ceramics (LTCC) technology for its high density integration. A coupling slot has been used to perform vertical integration, which can be easily optimized through its length. The measured input return loss within the bandwidth of interest (32 GHz-38 GHz) is less than -15 dB and -18 dB for the multilayer transition and the power divider, respectively. The lateral dimensions of a multilayer system, such as a feed network of an array, can be greatly reduced by employing these 3D slot-coupled components. © 2013 IEEE.

  9. Fast image retargeting based on strip dividing and resizing

    Institute of Scientific and Technical Information of China (English)

    Shungang Hua; Honglei Wei; Tieming Su

    2014-01-01

    Based on image strip dividing, an effective and fast image retargeting algorithm is proposed for resizing images. First, we construct the image energy map using gradient magnitude of the pixels and calculate the accumulated energy of each column, dividing the image into several strips by integrating similar energy columns. The reduced amount of dimension is decided in inverse proportion to the average energy for each strip. Then we retar-get the image combining scaling with cropping in terms of each strip’s reduced ratio. Experiment results show that the proposed algorithm is capable of implementing fast image retargeting and preserving both the local structures and the global visual effect of the image.

  10. Clobazam single or divided dose against diazepam in anxiety neurosis.

    Science.gov (United States)

    Channabasavanna, S M; Pinto Pereira, L M

    1986-01-01

    One-hundred-and-fifteen patients diagnosed as anxiety neurotics randomly received in a double blind study 20 mg clobazam (Frisium) as a single nightly dose (37 patients) or 10 mg b.d. (38 patients) or diazepam 5 mg b.d. (40 patients) for six weeks, followed by two weeks on placebo. Both the single and divided doses of clobazam were therapeutically equivalent to diazepam. After drug withdrawal, all three treatment groups continued to improve. Patients on clobazam showed better motor performance than the diazepam series. Patients on clobazam divided dose performed significantly better than those on diazepam. Minor side-effects occurred in all patients. From the results clobazam as a single dose of 20 mg has good anxiolysis without any hungover effect.

  11. Divided-aperture differential confocal fast-imaging microscopy

    Science.gov (United States)

    Wang, Yun; Qiu, Lirong; Zhao, Xiangye; Zhao, Weiqian

    2017-03-01

    A new method, laser divided-aperture differential confocal microscopy (DDCM), is proposed to achieve high-resolution 3D imaging of microstructures of large-scale sample surfaces. This method uses a divided-aperture confocal structure to significantly improve the axial resolution of confocal microscopy and keep a long working distance simultaneously; uses two radically offset point detectors to achieve differential detection to further improve the axial response sensitivity and realize fast imaging of a large-scale sample surface with a big axial scan-step interval. Theoretical analyses and experimental results show that the DDCM can reach an axial resolution of 5 nm with a 3.1 mm working distance with a 3 times imaging speed of a confocal system with the same resolution.

  12. Multiple-resolution clustering for recursive divide and conquer

    Science.gov (United States)

    Noel, Steven E.; Szu, Harold H.

    1997-04-01

    In recent work, a recursive divide-and-conquer approach was developed for path-minimization problems such as the traveling salesman problem (TSP). The approach is based on multiple-resolution clustering to decompose a problem into minimally-dependent parts. It is particularly effective for large-scale, fractal data sets, which exhibit clustering on all scales, and hence at all resolutions. This leads to the application of wavelets for performing the necessary multiple-resolution clustering. While the general topic of multiple-resolution clustering via wavelets is relatively immature, it has been explored for certain specific applications. However, nothing in the literature addresses the specific type of multiple-resolution clustering needed for the divide-and-conquer approach. That is the primary goal of this paper.

  13. A Divide-and-Conquer Strategy for Parsing

    CERN Document Server

    Shiuan, P L; Shiuan, Peh Li; Ann, Christopher Ting Hian

    1996-01-01

    In this paper, we propose a novel strategy which is designed to enhance the accuracy of the parser by simplifying complex sentences before parsing. This approach involves the separate parsing of the constituent sub-sentences within a complex sentence. To achieve that, the divide-and-conquer strategy first disambiguates the roles of the link words in the sentence and segments the sentence based on these roles. The separate parse trees of the segmented sub-sentences and the noun phrases within them are then synthesized to form the final parse. To evaluate the effects of this strategy on parsing, we compare the original performance of a dependency parser with the performance when it is enhanced with the divide-and-conquer strategy. When tested on 600 sentences of the IPSM'95 data sets, the enhanced parser saw a considerable error reduction of 21.2% in its accuracy.

  14. A Novel Nanometric Reversible Signed Divider with Overflow Checking Capability

    Directory of Open Access Journals (Sweden)

    Faraz Dastan

    2012-03-01

    Full Text Available One of the best approaches for designing future computers is that we use reversible logic. Reversible logic circuits have lower power consumption than the common circuits, used in computers nowadays. In this study we propose a new reversible division circuit. This reversible division circuit is signed divider and has an overflow checking capability. Among the designed and proposed reversible division circuits, our proposed division circuit is the first reversible signed divider with overflow checking capability which has been designed. In this circuit we use some reversible components like reversible parallel adder, reversible left-shift register, reversible multiplexer, reversible n-bit register and reversible n-bit register with parallel load line. In this paper all the scales are in the nanometric area.

  15. The plastid-dividing machinery: formation, constriction and fission.

    Science.gov (United States)

    Yoshida, Yamato; Miyagishima, Shin-ya; Kuroiwa, Haruko; Kuroiwa, Tsuneyoshi

    2012-12-01

    Plastids divide by constriction of the plastid-dividing (PD) machinery, which encircles the division site. The PD machinery consists of the stromal inner machinery which includes the inner PD and filamenting temperature-sensitive mutant Z (FtsZ) rings and the cytosolic outer machinery which includes the outer PD and dynamin rings. The major constituent of the PD machinery is the outer PD ring, which consists of a bundle of polyglucan filaments. In addition, recent proteomic studies suggest that the PD machinery contains additional proteins that have not been characterized. The PD machinery forms from the inside to the outside of the plastid. The constriction seems to occur by sliding of the polyglucan filaments of the outer PD ring, aided by dynamin. The final fission of the plastid is probably promoted by the 'pinchase' activity of dynamin.

  16. Combined method for parallel manipulator configuration design

    Institute of Scientific and Technical Information of China (English)

    2005-01-01

    Configuration design is an essential, creative and decision-making step in parallel manipulator design process, in which modeling and assembly are iterative and trivial. Combined approach with automatic parametric modeling and automatic assembly is proposed for parallel manipulator configuration design. The design process and key techniques, such as configuration design, configuration verification, poses calculation of all parts in parallel manipulator, virtual assembly and etc., are discussed and demonstrated by an example. A software package is developed for parallel manipulator configuration design based on the proposed method with Visual C+ + and UG/OPEN on Unigraphics.

  17. LDA optical setup using holographic imaging configuration

    Science.gov (United States)

    Ghosh, Abhijit; Nirala, A. K.

    2015-11-01

    This paper describes one of the possible ways for improving fringe quality at LDA measuring volume using a holographic imaging configuration consisting of a single hololens. For its comparative study with a conventional imaging configuration, a complete characterization of fringes formed at the measurement volume by both the configuration is presented. Results indicate the qualitative as well as quantitative improvement of the fringes formed at measurement volume by the holographic imaging configuration. Hence it is concluded that use of holographic imaging configuration for making LDA optical setup is a better choice than the conventional one.

  18. Crossing of Phantom Divide in $F(R)$ Gravity

    CERN Document Server

    Bamba, Kazuharu; Nojiri, Shin'ichi; Odintsov, Sergei D

    2010-01-01

    An explicit model of $F(R)$ gravity with realizing a crossing of the phantom divide is reconstructed. In particular, it is shown that the Big Rip singularity may appear in the reconstructed model of $F(R)$ gravity. Such a Big Rip singularity could be avoided by adding $R^2$ term or non-singular viable $F(R)$ theory to the model because phantom behavior becomes transient.

  19. Nonequilibrium stage modelling of dividing wall columns and experimental validation

    Science.gov (United States)

    Hiller, Christoph; Buck, Christina; Ehlers, Christoph; Fieg, Georg

    2010-11-01

    Dealing with complex process units like dividing wall columns pushes the focus on the determination of suitable modelling approaches. For this purpose a nonequilibrium stage model is developed. The successful validation is achieved by an experimental investigation of fatty alcohol mixtures under vacuum condition at pilot scale. Aim is the recovery of high purity products. The proposed model predicts the product qualities and temperature profiles very well.

  20. Histological findings of divided muscle after peroral endoscopic myotomy

    OpenAIRE

    Shiwaku, Hironari; Inoue, Haruhiro; Nimura, Satoshi; Yamashita, Kanefumi; Ohmiya, Toshihiro; Takeno, Shinsuke; Sasaki, Takamitsu; Yamashita, Yuichi

    2016-01-01

    Peroral endoscopic myotomy (POEM) is a revolutionary therapy for achalasia and related disorders. POEM utilizes almost the same myotomy procedure as the Heller myotomy; thus, it would be expected to have the same or greater duration of therapeutic effect. However, to date, there have been no reports to prove the basis for this procedure in achalasia. In this case, we were able to histologically show the divided muscle after POEM since the patient had an esophagectomy for esophageal cancer. Hi...

  1. Removal of direct current link harmonic ripple in single-phase voltage source inverter systems using supercapacitors

    OpenAIRE

    Hernandez, Gabriel D.

    2016-01-01

    Approved for public release; distribution is unlimited For an Energy Management System (EMS)-controlled microgrid that uses a single-phase voltage source inverter (VSI) configuration to supply power for AC loads from DC energy storage devices, the DC link connecting the VSI to the DC energy storage devices experiences a voltage ripple that is a second-order harmonic of the AC frequency. When the EMS has a battery bank as the only DC energy storage device, the DC link voltage ripple causes ...

  2. Dividing Streamline Formation Channel Confluences by Physical Modeling

    Directory of Open Access Journals (Sweden)

    Minarni Nur Trilita

    2010-02-01

    Full Text Available Confluence channels are often found in open channel network system and is the most important element. The incoming flow from the branch channel to the main cause various forms and cause vortex flow. Phenomenon can cause erosion of the side wall of the channel, the bed channel scour and sedimentation in the downstream confluence channel. To control these problems needed research into the current width of the branch channel. The incoming flow from the branch channel to the main channel flow bounded by a line distributors (dividing streamline. In this paper, the wide dividing streamline observed in the laboratory using a physical model of two open channels, a square that formed an angle of 30º. Observations were made with a variety of flow coming from each channel. The results obtained in the laboratory observation that the width of dividing streamline flow is influenced by the discharge ratio between the channel branch with the main channel. While the results of a comparison with previous studies showing that the observation in the laboratory is smaller than the results of previous research.

  3. FLOOD ROUTING MODELS IN CONFLUENT AND DIVIDING CHANNELS

    Institute of Scientific and Technical Information of China (English)

    范平; 李家春; 刘青泉

    2004-01-01

    By introducing a water depth connecting formula, the hydraulic equations in the dividing channel system were coupled and the relation of discharge distribution between the branches of the dividing channels can be yielded. In this manner, a numerical model for the confluent channels was established to study the variation of backwater effects with the parameters in the channel junction. The meeting of flood peaks in the mainstream and tributary can be analyzed with this model. The flood peak meeting is found to be a major factor for the extremely high water level in the mainstream during the 1998 Yangtze River flood. Subsequently the variations of discharge distribution and water level with channel parameters between each branch in this system were studied as well. As a result, flood evolution caused by Jingjiang River shortcut and sediment deposition in the entrance of dividing channels of the Yangtze River may be qualitatively elucidated. It is suggested to be an effective measure for flood mitigation to enhance regulation capability of reservoirs available upstream of the tributaries and harness branch entrance channels.

  4. 49 CFR 236.551 - Power supply voltage; requirement.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 4 2010-10-01 2010-10-01 false Power supply voltage; requirement. 236.551 Section... supply voltage; requirement. The voltage of power supply shall be maintained within 10 percent of rated voltage....

  5. Voltage-controlled narrowband and wide, variable-range four-segment quartz crystal oscillator.

    Science.gov (United States)

    Ruslan, Ruzaini; Satoh, Tomio; Akitsu, Tetsuya

    2012-03-01

    In this work, our goal is to develop a voltage-controlled variable-frequency quartz crystal oscillator with narrowband response, wide, variable frequency range and the capacity to oscillate across the series resonance frequency using a four-segment configuration of a quartz crystal oscillator. In conventional quartz oscillators, the quartz resonator is inserted in the feedback loop between the input and the output of the active circuit, providing sufficient gain and the phase relation. In the oscillator developed here, the quartz crystal resonator is inserted between the loop circuit and the ground potential. The performance of the voltage-controlled variable-frequency oscillator is demonstrated across the series resonance frequency.

  6. Background voltage distortion influence on power electric systems in the presence of the Steinmetz circuit

    Energy Technology Data Exchange (ETDEWEB)

    Sainz, Luis; Pedra, Joaquin [Department of Electrical Engineering, ETSEIB-UPC, Av. Diagonal 647, 08028 Barcelona (Spain); Caro, Manuel [IDOM Ingenieria y Arquitectura, C. Barcas 2, 46002 Valencia (Spain)

    2009-01-15

    In traction systems, it is usual to connect reactances in delta configuration with single-phase loads to reduce voltage unbalances and avoid electric system operation problems. This set is known as Steinmetz circuit. Parallel and series resonances can occur due to the capacitive reactance of the Steinmetz circuit and affect power quality. In this paper, the series resonance ''observed'' from the supply system is numerically located. The study of this resonance is important to avoid problems due to background voltage distortion. Experimental measurements are also presented to validate the obtained numerical results. (author)

  7. Voltage Unbalance Compensation with Smart Three-phase Loads

    DEFF Research Database (Denmark)

    Douglass, Philip; Trintis, Ionut; Munk-Nielsen, Stig

    2016-01-01

    voltage, but it does not reduce the negative sequence voltage. The controller that uses phase-phase voltage as input eliminates negative sequence voltage, and reduces voltage deviations from the average to approximately half their initial value. Current unbalance is reduced when the voltage unbalance...... is caused by asymmetrical loads. These results suggest that the optimal algorithm to reduce system unbalance depends on which system parameter is most important: phase-neutral voltage unbalance, phase-phase voltage unbalance, or current unbalance....

  8. Comparison of Harmony Search Algorithm and Particle Swarm Optimization for Distributed Generation Allocation to Improve Steady State Voltage Stability of Distribution Networks

    Directory of Open Access Journals (Sweden)

    Hamed Piarehzadeh

    2012-08-01

    Full Text Available In this study is tried to optimal distributed generation allocation for stability improvement in radial distribution systems. Voltage instability implies an uncontrolled decrease in voltage triggered by a disturbance, leading to voltage collapse and is primarily caused by dynamics connected with the load. The instability is divided into steady state and transient voltage instability Based on the time spectrum of the incident of the phenomena. The analysis is accomplished using a steady state voltage stability index which can be evaluated at each node of the distribution system. Several optimal capacities and locations are used to check these results. The location of DG has the main effect voltage stability on the system. Effects of location and capacity on incrementing steady state voltage stability in radial distribution systems are examined through Harmony Search Algorithm (HSA and finally the results are compared to Particle Swarm Optimization (PSO on the terms of speed, convergence and accuracy.

  9. Neutral electrolyte aluminum air battery with open configuration

    Institute of Scientific and Technical Information of China (English)

    HAN Bin; LIANG Guangchuan

    2006-01-01

    A kind of new long life aluminum air batteries with open configuration was developed, using aluminum alloy doped with Ga, In, Sn, Bi, Pb and Mn as anode, NaCl solution as electrolyte and air electrode as cathode. The polarization curves of aluminum electrode and air electrode were tested. And the cell's performance was tested to calculate the utilization of aluminum electrode and the energy density. It is shown that, in the 3.5% NaCl solution, the cell can discharge at 0.29 A for 140 h with the working voltage keeping over 1.1 V. The utilization ratio of aluminum anode is over 44%, and the life of battery is longer than 2400 h.

  10. Power conditioning using dynamic voltage restorers under different voltage sag types

    Directory of Open Access Journals (Sweden)

    Ahmed M. Saeed

    2016-01-01

    Full Text Available Voltage sags can be symmetrical or unsymmetrical depending on the causes of the sag. At the present time, one of the most common procedures for mitigating voltage sags is by the use of dynamic voltage restorers (DVRs. By definition, a DVR is a controlled voltage source inserted between the network and a sensitive load through a booster transformer injecting voltage into the network in order to correct any disturbance affecting a sensitive load voltage. In this paper, modelling of DVR for voltage correction using MatLab software is presented. The performance of the device under different voltage sag types is described, where the voltage sag types are introduced using the different types of short-circuit faults included in the environment of the MatLab/Simulink package. The robustness of the proposed device is evaluated using the common voltage sag indices, while taking into account voltage and current unbalance percentages, where maintaining the total harmonic distortion percentage of the load voltage within a specified range is desired. Finally, several simulation results are shown in order to highlight that the DVR is capable of effective correction of the voltage sag while minimizing the grid voltage unbalance and distortion, regardless of the fault type.

  11. Power conditioning using dynamic voltage restorers under different voltage sag types.

    Science.gov (United States)

    Saeed, Ahmed M; Abdel Aleem, Shady H E; Ibrahim, Ahmed M; Balci, Murat E; El-Zahab, Essam E A

    2016-01-01

    Voltage sags can be symmetrical or unsymmetrical depending on the causes of the sag. At the present time, one of the most common procedures for mitigating voltage sags is by the use of dynamic voltage restorers (DVRs). By definition, a DVR is a controlled voltage source inserted between the network and a sensitive load through a booster transformer injecting voltage into the network in order to correct any disturbance affecting a sensitive load voltage. In this paper, modelling of DVR for voltage correction using MatLab software is presented. The performance of the device under different voltage sag types is described, where the voltage sag types are introduced using the different types of short-circuit faults included in the environment of the MatLab/Simulink package. The robustness of the proposed device is evaluated using the common voltage sag indices, while taking into account voltage and current unbalance percentages, where maintaining the total harmonic distortion percentage of the load voltage within a specified range is desired. Finally, several simulation results are shown in order to highlight that the DVR is capable of effective correction of the voltage sag while minimizing the grid voltage unbalance and distortion, regardless of the fault type.

  12. A Revive on 32×32 Bit Multiprecision Dynamic Voltage Scaling Multiplier with Operands Scheduler

    Directory of Open Access Journals (Sweden)

    Mrs.S.N.Rawat

    2016-02-01

    Full Text Available In this paper, we present a Multiprecision (MP reconfigurable multiplier that incorporates variable precision, parallel processing (PP, razor-based dynamic voltage scaling (DVS, and dedicated MP operands scheduling to provide optimum performance for a variety of operating conditions. All of the building blocks of the proposed reconfigurable multiplier can either work as independent smaller-precision multipliers or work in parallel to perform higher-precision multiplications. Given the user’s requirements (e.g., throughput, a dynamic voltage/ frequency scaling management unit configures the multiplier to operate at the proper precision and frequency. Adapting to the run-time workload of the targeted application, razor flip-flops together with a dithering voltage unit then configure the multiplier to achieve the lowest power consumption. The single-switch dithering voltage unit and razor flip-flops help to reduce the voltage safety margins and overhead typically associated to DVS to the lowest level. The large silicon area and power overhead typically associated to reconfigurability features are removed. Finally, the proposed novel MP multiplier can further benefit from an operands scheduler that rearranges the input data, hence to determine the optimum voltage and frequency operating conditions for minimum power consumption. This low-power MP multiplier is fabricated in AMIS 0.35-μm technology. Experimental results show that the proposed MP design features a 28.2% and 15.8% reduction in circuit area and power consumption compared with conventional fixed-width multiplier. When combining this MP design with error-tolerant razor-based DVS, PP, and the proposed novel operands scheduler, 77.7%–86.3% total power reduction is achieved with a total silicon area overhead as low as 11.1%. This paper successfully demonstrates that a MP architecture can allow more aggressive frequency/supply voltage scaling for improved power efficiency

  13. Configurable software for satellite graphics

    Energy Technology Data Exchange (ETDEWEB)

    Hartzman, P D

    1977-12-01

    An important goal in interactive computer graphics is to provide users with both quick system responses for basic graphics functions and enough computing power for complex calculations. One solution is to have a distributed graphics system in which a minicomputer and a powerful large computer share the work. The most versatile type of distributed system is an intelligent satellite system in which the minicomputer is programmable by the application user and can do most of the work while the large remote machine is used for difficult computations. At New York University, the hardware was configured from available equipment. The level of system intelligence resulted almost completely from software development. Unlike previous work with intelligent satellites, the resulting system had system control centered in the satellite. It also had the ability to reconfigure software during realtime operation. The design of the system was done at a very high level using set theoretic language. The specification clearly illustrated processor boundaries and interfaces. The high-level specification also produced a compact, machine-independent virtual graphics data structure for picture representation. The software was written in a systems implementation language; thus, only one set of programs was needed for both machines. A user can program both machines in a single language. Tests of the system with an application program indicate that is has very high potential. A major result of this work is the demonstration that a gigantic investment in new hardware is not necessary for computing facilities interested in graphics.

  14. Absolute configuration of isovouacapenol C

    Directory of Open Access Journals (Sweden)

    Hoong-Kun Fun

    2010-08-01

    Full Text Available The title compound, C27H34O5 {systematic name: (4aR,5R,6R,6aS,7R,11aS,11bR-4a,6-dihydroxy-4,4,7,11b-tetramethyl-1,2,3,4,4a,5,6,6a,7,11,11a,11b-dodecahydrophenanthro[3,2-b]furan-5-yl benzoate}, is a cassane furanoditerpene, which was isolated from the roots of Caesalpinia pulcherrima. The three cyclohexane rings are trans fused: two of these are in chair conformations with the third in a twisted half-chair conformation, whereas the furan ring is almost planar (r.m.s. deviation = 0.003 Å. An intramolecular C—H...O interaction generates an S(6 ring. The absolute configurations of the stereogenic centres at positions 4a, 5, 6, 6a, 7, 11a and 11b are R, R, R, S, R, S and R, respectively. In the crystal, molecules are linked into infinite chains along [010] by O—H...O hydrogen bonds. C...O [3.306 (2–3.347 (2 Å] short contacts and C—H...π interactions also occur.

  15. Implementation of Dividing Cubes Algorithm Based on CUDA%基于 CUDA 的 Dividing Cubes 算法实现

    Institute of Scientific and Technical Information of China (English)

    张文波; 曹耀钦; 孙伟; 李海龙

    2013-01-01

    In traditional Dividing Cubes algorithm ,voxels are divided into many small elements in one time which bring a large number of calculations .Therefore ,a progressive subdivision is proposed to reduce calculations .In the meanwhile ,the algorithm is transplanted into GPU , and implemented based on CUDA . The kernel , thread organization and memory allocation is also designed .Experimental results show that almost 10 times speedup is reached by using GPU′s parallel acceleration capacity .%针对传统Dividing Cubes算法中一次性将体元剖分为较小体元而带来大量计算的问题,提出递进式的体元剖分方式,以减少剖分过程中的计算量。同时,将算法移植到图形处理器(GPU )上执行,在统一计算设备架构(CUDA )下对其进行实现,并分别对 kernel函数、线程结构和存储空间进行了设计和分配。实验结果表明,利用GPU的并行加速能力可以达到将近10倍的加速比,有效地提升了等值面的绘制速度。

  16. High voltage load resistor array

    Energy Technology Data Exchange (ETDEWEB)

    Lehmann, Monty Ray [Smithfield, VA

    2005-01-18

    A high voltage resistor comprising an array of a plurality of parallel electrically connected resistor elements each containing a resistive solution, attached at each end thereof to an end plate, and about the circumference of each of the end plates, a corona reduction ring. Each of the resistor elements comprises an insulating tube having an electrode inserted into each end thereof and held in position by one or more hose clamps about the outer periphery of the insulating tube. According to a preferred embodiment, the electrode is fabricated from stainless steel and has a mushroom shape at one end, that inserted into the tube, and a flat end for engagement with the end plates that provides connection of the resistor array and with a load.

  17. Single dielectric barrier discharge characteristics in needle-to-plane configuration

    Science.gov (United States)

    Emelyanov, O. A.; Shemet, M. V.

    2014-08-01

    Single dielectric barrier discharges (DBDs) in the ‘needle—submillimetric air gap—polymer barrier—plane’ configuration were investigated. The measurements of breakdown voltages, discharge current pulses, transferred charges and surface charge distributions for both needle polarities were conducted by the developed experimental setup. For the same gaps the breakdown voltage and the accumulated surface charge for the positive needle polarity are larger than the ones for the negative polarity. It is shown that the main contribution to the DBD current pulse and accumulated charge is determined by the surface phase of discharge process. Additionally the subsequent DBD development during one period of the applied voltage of triangular waveform was observed. The results indicate a ‘memory effect’ of the DBD development.

  18. A Novel Multilevel Quad-Inverter Configuration for Quasi Six-Phase Open-Winding Converter

    DEFF Research Database (Denmark)

    Padmanaban, Sanjeevi Kumar; Blaabjerg, Frede; Wheeler, Patrick

    2016-01-01

    -level modulation (MSCFM) algorithm is developed in this work and easy for implementing in real digital processors. The proposed modulation algorithm is capable of generating, 5-level voltages at each output of four VSI as one equivalent to multilevel inverter. The total power is among the four DC sources......This paper developed a novel quad-inverter configuration for multilevel six-phase asymmetrical open-winding AC converter. Proposal found to be suited for (low-voltage/high-current) applications such as AC tractions and `More-Electric Aircraft' propulsion systems. Modular power circuit comprises...... of standard four three-phase voltage source inverter (VSI) and each connected to the open-end windings. Each VSIs are incorporated with one bi-directional switching device (MOSFET/IGBT) per phase and two capacitors with neutral point connected. Further, an original modified single carrier five...

  19. Programable Driver for Voltage-Controlled Oscillators

    Science.gov (United States)

    Fowler, L. E.; Mcneil, J. A.

    1985-01-01

    Electronically programable read-only memory (EPROM) and digital-to-analog converter provide customized time-varying voltage for frequency modulation. Voltage used to modulate IMPATT oscillator that serves as microwave pump for solid-state maser in low-noise amplifier. EPROM simple to tailor voltage waveform to suit characteristics of given maser. Digital information for waveform programed into EPROM chip; digital-to-analog converter reads information and produces corresponding analog wave. Principle readily adapted to other applications.

  20. Generator of ultrashort megavolt voltage pulses

    CERN Document Server

    Zheltov, K A; Shalimanov, V F

    2002-01-01

    Paper describes approx 3 ns duration and > 1 MW amplitude voltage pulse generator under high-ohmic (approx 450 Ohm) load. Generator comprises pulse transformer with magnetized core, as well as, resonance tuned circuit of high-voltage solenoid and accumulating spaces of a shaping line containing, moreover, spark gap to switch charge in transmitting line. Paper contains the results of voltage measuring in generator basic units

  1. Investigation of pulsed voltage limiters characteristics

    Directory of Open Access Journals (Sweden)

    Karimov A. V.

    2012-06-01

    Full Text Available A new method for measuring the voltage limit is offered. It has been designed to measure high-power pulsed current of voltage limiters. The error of this method is half as much as the error of the known method of direct measurement. The investigation of dependence of power capability of single-crystal and double-crystal voltage limiters and of the pulsed operation time on pulse duration.

  2. BRIDGING THE KNOWLEDGE DIVIDE Educational Technology for Development

    OpenAIRE

    2009-01-01

    BRIDGING THE KNOWLEDGE DIVIDEEducational Technology for DevelopmentMarshall,S., Kinuthia, W. & Wallace Taylor., Ed.D.; Information Age Publishing, Charlotte, NC, SBN: 978-1-60752-109-9, p.433, 2009Reviewed by Ozlem OZANFaculty of EducationEskişehir Osmangazi UniversityEskisehir, TURKEYThe concept of a knowledge divide is used to describe the gap in living conditions between those who can find, manage and process information or knowledge, and those who are impaired in this, for one reason or a...

  3. Observations favor the crossing of phantom divide lines

    Institute of Scientific and Technical Information of China (English)

    2010-01-01

    Using three different parameterized dark energy models, we reconstruct the properties of dark energy from the latest 397 Sne Ia, CMB and BAO with the present matter density, Ωm0, given prior. We find that, when Ωm0 is not small, for example, Ωm0 = 0.28 or 0.32, an evolving dark energy with a crossing of phantom divide line is favored and this conclusion seems to be model independent. We also find that the evolving properties of dark energy become more and more evident with the increase of Ωm0 given prior.

  4. Blurring of the public/private divide: the Canadian chapter.

    Science.gov (United States)

    Flood, Colleen M; Thomas, Bryan

    2010-06-01

    Blurring of public/private divide is occurring in different ways around the world, with differential effects in terms of access and equity. In Canada, one pathway towards privatization has received particular attention: duplicative private insurance, allowing those with the financial means to bypass queues in the public system. We assess recent legal and policy developments on this front, but also describe other trends towards the blurring of public and private in Canada: the reliance on mandated private insurance for pharmaceutical coverage; provincial governments' reliance on public-private partnerships to finance hospitals; and the incorporation of for-profit clinics within the public health care system.

  5. The NCI Digital Divide Pilot Projects: implications for cancer education.

    Science.gov (United States)

    Kreps, Gary L; Gustafson, David; Salovey, Peter; Perocchia, Rosemarie Slevin; Wilbright, Wayne; Bright, Mary Anne; Muha, Cathy

    2007-01-01

    The National Cancer Institute (NCI) supported four innovative demonstration research projects, "The Digital Divide Pilot Projects," to test new strategies for disseminating health information via computer to vulnerable consumers. These projects involved active research collaborations between the NCI's Cancer Information Service (CIS) and regional cancer control researchers to field test new approaches for enhancing cancer communication in vulnerable communities. The projects were able to use computers to successfully disseminate relevant cancer information to vulnerable populations. These demonstration research projects suggested effective new strategies for using communication technologies to educate underserved populations about cancer prevention, control, and care.

  6. Digital Television, Convergence, and the Public: Another Digital Divide?

    Directory of Open Access Journals (Sweden)

    Jason Smith

    2009-06-01

    Full Text Available While 85 percent of Americans pay to receive television signals through satellite or cable companies, 15 percent still receive their television using over-the-air signals. With the elminination of analog television signals, the 15 percent of households have had to make significant changes in their viewing technology. These households tend to be elderly, poor, minority and rural. Signal coverage areas will be cut back, since government assumed a viewer would have an antenna on a 30 foot pole. Few do, and governmental programs delibertely hid this engineering fact. It is argued that digitalism has neglected the public use of the airways and created yet one more digital divide.

  7. Korean Nationalism in a Divided Nation: Challenges to US Policy

    OpenAIRE

    Olsen, Edward A.

    2008-01-01

    The article of record as published may be found at http://dx.doi.org/10.1111/j.1976-5118.2008.00002.x Korean nationalism poses challenges for Koreans dwelling in each half of the divided Korean nation because each half of the nation must simultaneously deal with both their own and the other half’s form of semi-nationalism and also with peninsular pan-nationalism. Coping with these three forms of nationalism is also a problem for US policy toward each Korean state and toward ...

  8. CLOBAZAM SINGLE OR DIVIDED DOSE AGAINST DIAZEPAM IN ANXIETY NEUROSIS

    OpenAIRE

    1986-01-01

    SUMMARY One-hundred-and-fifteen patients diagnosed as anxiety neurotics randomly received in a double blind study 20 mg clobazam (Frisium) as a single nightly dose (37 patients) or 10 mg b.d. (38 patients) or diazepam 5 mg b.d. (40 patients) for six weeks, followed by two weeks on placebo. Both the single and divided doses of clobazam were therapeutically equivalent to diazepam. After drug withdrawal, all three treatment groups continued to improve. Patients on clobazam showed better motor pe...

  9. Traffic Prediction Based on SVM Training Sample Divided by Time

    Directory of Open Access Journals (Sweden)

    Lingli Li

    2013-07-01

    Full Text Available In recent years, the volume of traffic is rapidly increasing. When vehicles running through the tunnel are more intensive or move slowly, the tunnel environment occurs deteriorated sharply, which affects the normal operation of the vehicle in the tunnel. This paper uses the result of previous mining association rules to select feature items and to establish four training samples divided by time. Then the training samples are utilized to create the SVM classification model. Finally the trained SVM model is used to prediction the tunnel traffic situation. Through traffic situation prediction, effective decisions can be made before traffic jams, and ensure that the tunnel traffic is normal.  

  10. Transition duct with divided upstream and downstream portions

    Energy Technology Data Exchange (ETDEWEB)

    McMahan, Kevin Weston; LeBegue, Jeffrey Scott; Maldonado, Jaime Javier; Dillard, Daniel Jackson; Flanagan, James Scott

    2015-07-14

    Turbine systems are provided. In one embodiment, a turbine system includes a transition duct comprising an inlet, an outlet, and a duct passage extending between the inlet and the outlet and defining a longitudinal axis, a radial axis, and a tangential axis. The outlet of the transition duct is offset from the inlet along the longitudinal axis and the tangential axis. The duct passage includes an upstream portion extending from the inlet and a downstream portion extending from the outlet. The turbine system further includes a rib extending from an outer surface of the duct passage, the rib dividing the upstream portion and the downstream portion.

  11. Dynamic airspace configuration method based on a weighted graph model

    Directory of Open Access Journals (Sweden)

    Chen Yangzhou

    2014-08-01

    Full Text Available This paper proposes a new method for dynamic airspace configuration based on a weighted graph model. The method begins with the construction of an undirected graph for the given airspace, where the vertices represent those key points such as airports, waypoints, and the edges represent those air routes. Those vertices are used as the sites of Voronoi diagram, which divides the airspace into units called as cells. Then, aircraft counts of both each cell and of each air-route are computed. Thus, by assigning both the vertices and the edges with those aircraft counts, a weighted graph model comes into being. Accordingly the airspace configuration problem is described as a weighted graph partitioning problem. Then, the problem is solved by a graph partitioning algorithm, which is a mixture of general weighted graph cuts algorithm, an optimal dynamic load balancing algorithm and a heuristic algorithm. After the cuts algorithm partitions the model into sub-graphs, the load balancing algorithm together with the heuristic algorithm transfers aircraft counts to balance workload among sub-graphs. Lastly, airspace configuration is completed by determining the sector boundaries. The simulation result shows that the designed sectors satisfy not only workload balancing condition, but also the constraints such as convexity, connectivity, as well as minimum distance constraint.

  12. Dynamic airspace configuration method based on a weighted graph model

    Institute of Scientific and Technical Information of China (English)

    Chen Yangzhou; Zhang Defu

    2014-01-01

    This paper proposes a new method for dynamic airspace configuration based on a weighted graph model. The method begins with the construction of an undirected graph for the given airspace, where the vertices represent those key points such as airports, waypoints, and the edges represent those air routes. Those vertices are used as the sites of Voronoi diagram, which divides the airspace into units called as cells. Then, aircraft counts of both each cell and of each air-route are computed. Thus, by assigning both the vertices and the edges with those aircraft counts, a weighted graph model comes into being. Accordingly the airspace configuration problem is described as a weighted graph partitioning problem. Then, the problem is solved by a graph par-titioning algorithm, which is a mixture of general weighted graph cuts algorithm, an optimal dynamic load balancing algorithm and a heuristic algorithm. After the cuts algorithm partitions the model into sub-graphs, the load balancing algorithm together with the heuristic algorithm trans-fers aircraft counts to balance workload among sub-graphs. Lastly, airspace configuration is com-pleted by determining the sector boundaries. The simulation result shows that the designed sectors satisfy not only workload balancing condition, but also the constraints such as convexity, connec-tivity, as well as minimum distance constraint.

  13. Low-Voltage Switched-Capacitor Circuits

    DEFF Research Database (Denmark)

    Bidari, E.; Keskin, M.; Maloberti, F.

    1999-01-01

    Switched-capacitor stages are described which can function with very low (typically 1 V) supply voltages, without using voltage boosting or switched op-amps. Simulations indicate that high performance may be achieved using these circuits in filter or data converter applications.......Switched-capacitor stages are described which can function with very low (typically 1 V) supply voltages, without using voltage boosting or switched op-amps. Simulations indicate that high performance may be achieved using these circuits in filter or data converter applications....

  14. Characterisation of the VELO High Voltage System

    CERN Document Server

    Rakotomiaramanana, B; Eklund, L

    2008-01-01

    The high voltage system supplies the bias voltage to the 88 silicon sensors which comprise the LHCb Vertex Locator (VELO). This note describes the results of the tests which have been performed on the hardware of the high voltage system of the VELO. Each individual test detailed in this note corresponds to a specific requirement of the system. These requirements arise primarily from ensuring the safety of the silicon sensors and the quality of the data taken from the VELO modules. The tests performed are in four categories: normal operation of the high voltage system; vercation of its stability under operation; discussion of its behaviour in failure modes; and details of operation at low voltage. Noteworthy issues, identified through the tests, include the behaviour of the high voltage modules at voltages below 9V, the current limit that can be applied during ramping of the voltage, and the speed with which the voltage is cut during failures of the system. The results of these tests provide high confidence th...

  15. Characterisation of the VELO High Voltage System

    CERN Document Server

    Rakotomiaramanana, B; Parkes, C; Eklund, L

    2008-01-01

    The high voltage system supplies the bias voltage to the 88 silicon sensors which comprise the LHCb Vertex Locator (VELO). This note describes the results of the tests which have been performed on the hardware of the high voltage system of the VELO. Each individual test detailed in this note corresponds to a specific requirement of the system. These requirements arise primarily from ensuring the safety of the silicon sensors and the quality of the data taken from the VELO modules. The tests performed are in four categories: normal operation of the high voltage system; verification of its stability under operation; discussion of its behaviour in failure modes; and details of operation at low voltage. Noteworthy issues, identified through the tests, include the behaviour of the high voltage modules at voltages below 9V, the current limit that can be applied during ramping of the voltage, and the speed with which the voltage is cut during failures of the system. The results of these tests provide high confidence...

  16. Microprocessor-controlled, programmable ramp voltage generator

    Energy Technology Data Exchange (ETDEWEB)

    Hopwood, J.

    1978-11-01

    A special-purpose voltage generator has been developed for driving the quadrupole mass filter of a residual gas analyzer. The generator is microprocessor-controlled with desired ramping parameters programmed by setting front-panel digital thumb switches. The start voltage, stop voltage, and time of each excursion are selectable. A maximum of five start-stop levels may be pre-selected for each program. The ramp voltage is 0 to 10 volts with sweep times from 0.1 to 999.99 seconds.

  17. Magnetoelectric voltage coefficients of magnetoelectric composites

    Institute of Scientific and Technical Information of China (English)

    WAN Yong-ping; ZHONG Zheng; QIU Jin-hao

    2006-01-01

    The magnetoelectric(ME) effect of the particulate magnetostrictive/piezoelectric composite was theoretically studied. The dependence of the ME voltage coefficients on the material properties of the magnetostrictive phase was discussed. The permittivity,permeability and the elastic modulus of the magnetostrictive phase generally have obvious influences on the ME voltage coefficients. The magnetostrictive phase with a large permittivity,large permeability or stiffer modulus will respectively contribute to the higher ME voltage coefficients. For a certain kind of piezoelectric matrix,the ME voltage coefficients can be improved to some extent by choosing those magnetostrictive materials with large permittivity,permeability or high elastic modulus.

  18. Maximum permissible voltage of YBCO coated conductors

    Energy Technology Data Exchange (ETDEWEB)

    Wen, J.; Lin, B.; Sheng, J.; Xu, J.; Jin, Z. [Department of Electrical Engineering, Shanghai Jiao Tong University, Shanghai (China); Hong, Z., E-mail: zhiyong.hong@sjtu.edu.cn [Department of Electrical Engineering, Shanghai Jiao Tong University, Shanghai (China); Wang, D.; Zhou, H.; Shen, X.; Shen, C. [Qingpu Power Supply Company, State Grid Shanghai Municipal Electric Power Company, Shanghai (China)

    2014-06-15

    Highlights: • We examine three kinds of tapes’ maximum permissible voltage. • We examine the relationship between quenching duration and maximum permissible voltage. • Continuous I{sub c} degradations under repetitive quenching where tapes reaching maximum permissible voltage. • The relationship between maximum permissible voltage and resistance, temperature. - Abstract: Superconducting fault current limiter (SFCL) could reduce short circuit currents in electrical power system. One of the most important thing in developing SFCL is to find out the maximum permissible voltage of each limiting element. The maximum permissible voltage is defined as the maximum voltage per unit length at which the YBCO coated conductors (CC) do not suffer from critical current (I{sub c}) degradation or burnout. In this research, the time of quenching process is changed and voltage is raised until the I{sub c} degradation or burnout happens. YBCO coated conductors test in the experiment are from American superconductor (AMSC) and Shanghai Jiao Tong University (SJTU). Along with the quenching duration increasing, the maximum permissible voltage of CC decreases. When quenching duration is 100 ms, the maximum permissible of SJTU CC, 12 mm AMSC CC and 4 mm AMSC CC are 0.72 V/cm, 0.52 V/cm and 1.2 V/cm respectively. Based on the results of samples, the whole length of CCs used in the design of a SFCL can be determined.

  19. Development of a voltage scanner of chopper

    CERN Document Server

    Shen Guan Ren; LiShengLi; WangQuanXing; Wu Long Cheng

    2001-01-01

    Development of voltage sweeper of chopper with CPNG are introduced. Voltage sweeper is one of important key parts of chopper. Two years working prove that it is stable and reliable. Its main technology performance save: sine wave frequency: 750 kHz +- 20 Hz; total distortion: 65 Db; output voltage (V-V): 0->=4000 V; the error7 W; voltage supply: 220V AC +-10%, 50 +- 1 Hz; total power supply: <100W; Work temperature range: 0 - 40 degree; Stability in long time <=1%

  20. Improvement of the characteristics of inductive dividers due to the use of electronic devices; Mejora en las caracteristicas de divisores inductivos mediante el uso de dispositivos electronicos

    Energy Technology Data Exchange (ETDEWEB)

    Slomovitz, Daniel [UTE - Laboratorio, Montevideo (Uruguay)

    1996-12-31

    This work present a new system of electronic compensation for decrease the errors of inductive dividers and measure transformers of voltage. A auxiliary current amplifier reduce the magnetization current, main source of errors in this devices, in low frequency. Simultaneously rise the input impedance. This method permit the construction of small devices, few weight and little errors, without overload in the input circuits that is connected 5 refs., 1 fig., 2 tabs.