WorldWideScience

Sample records for voc emission ratios

  1. VOC emissions chambers

    Data.gov (United States)

    Federal Laboratory Consortium — In order to support the development of test methods and reference materials for volatile organic compounds (VOC) emissions from building materials and furnishings,...

  2. Contrasting winter and summer VOC mixing ratios at a forest site in the Western Mediterranean Basin: the effect of local biogenic emissions

    Science.gov (United States)

    Seco, R.; Peñuelas, J.; Filella, I.; Llusià, J.; Molowny-Horas, R.; Schallhart, S.; Metzger, A.; Müller, M.; Hansel, A.

    2011-12-01

    Atmospheric volatile organic compounds (VOCs) are involved in ozone and aerosol generation, thus having implications for air quality and climate. VOCs and their emissions by vegetation also have important ecological roles as they can protect plants from stresses and act as communication cues between plants and between plants and animals. In spite of these key environmental and biological roles, the reports on seasonal and daily VOC mixing ratios in the literature for Mediterranean natural environments are scarce. We conducted seasonal (winter and summer) measurements of VOC mixing ratios in an elevated (720 m a.s.l.) holm oak Mediterranean forest site near the metropolitan area of Barcelona (NE Iberian Peninsula). Methanol was the most abundant compound among all the VOCs measured in both seasons. While aromatic VOCs showed almost no seasonal variability, short-chain oxygenated VOCs presented higher mixing ratios in summer, presumably due to greater emission by vegetation and increased photochemistry, both enhanced by the high temperatures and solar radiation in summer. Isoprenoid VOCs showed the biggest seasonal change in mixing ratios: they increased by one order of magnitude in summer, as a result of the vegetation's greater physiological activity and emission rates. The maximum diurnal concentrations of ozone increased in summer too, most likely due to more intense photochemical activity and the higher levels of VOCs in the air. The daily variation of VOC mixing ratios was mainly governed by the wind regime of the mountain, as the majority of the VOC species analyzed followed a very similar diel cycle. Mountain and sea breezes that develop after sunrise advect polluted air masses to the mountain. These polluted air masses had previously passed over the urban and industrial areas surrounding the Barcelona metropolitan area, where they were enriched in NOx and in VOCs of biotic and abiotic origin. Moreover, these polluted air masses receive additional biogenic

  3. Contrasting winter and summer VOC mixing ratios at a forest site in the Western Mediterranean Basin: the effect of local biogenic emissions

    Directory of Open Access Journals (Sweden)

    R. Seco

    2011-12-01

    Full Text Available Atmospheric volatile organic compounds (VOCs are involved in ozone and aerosol generation, thus having implications for air quality and climate. VOCs and their emissions by vegetation also have important ecological roles as they can protect plants from stresses and act as communication cues between plants and between plants and animals. In spite of these key environmental and biological roles, the reports on seasonal and daily VOC mixing ratios in the literature for Mediterranean natural environments are scarce.

    We conducted seasonal (winter and summer measurements of VOC mixing ratios in an elevated (720 m a.s.l. holm oak Mediterranean forest site near the metropolitan area of Barcelona (NE Iberian Peninsula. Methanol was the most abundant compound among all the VOCs measured in both seasons. While aromatic VOCs showed almost no seasonal variability, short-chain oxygenated VOCs presented higher mixing ratios in summer, presumably due to greater emission by vegetation and increased photochemistry, both enhanced by the high temperatures and solar radiation in summer. Isoprenoid VOCs showed the biggest seasonal change in mixing ratios: they increased by one order of magnitude in summer, as a result of the vegetation's greater physiological activity and emission rates. The maximum diurnal concentrations of ozone increased in summer too, most likely due to more intense photochemical activity and the higher levels of VOCs in the air.

    The daily variation of VOC mixing ratios was mainly governed by the wind regime of the mountain, as the majority of the VOC species analyzed followed a very similar diel cycle. Mountain and sea breezes that develop after sunrise advect polluted air masses to the mountain. These polluted air masses had previously passed over the urban and industrial areas surrounding the Barcelona metropolitan area, where they were enriched in NOx and in VOCs of biotic and abiotic origin. Moreover, these

  4. Reducing VOC Press Emission from OSB Manufacturing

    Energy Technology Data Exchange (ETDEWEB)

    Dr. Gary D. McGinnis; Laura S. WIlliams; Amy E. Monte; Jagdish Rughani: Brett A. Niemi; Thomas M. Flicker

    2001-12-31

    Current regulations require industry to meet air emission standards with regard to particulates, volatile organic compounds (VOCs), hazardous air pollutants (HAPs) and other gases. One of many industries that will be affected by the new regulations is the wood composites industry. This industry generates VOCs, HAPs, and particulates mainly during the drying and pressing of wood. Current air treatment technologies for the industry are expensive to install and operate. As regulations become more stringent, treatment technologies will need to become more efficient and cost effective. The overall objective of this study is to evaluate the use of process conditions and chemical additives to reduce VOC/HAPs in air emitted from presses and dryers during the production of oriented strand board.

  5. Anthropogenic VOC speciation in emission inventories: a method for improvement and evaluation

    Science.gov (United States)

    von Schneidemesser, E.; D'angiola, A.; Granier, C.; Monks, P. S.; Law, K.

    2011-12-01

    Volatile organic compounds (VOCs) are important precursor compounds for the formation of ozone and other secondary organic aerosols. Anthropogenic sources of VOCs are dominated by industrial usage and transportation sources, the latter being extremely important in urban areas. Megacities and large urban conglomerations are emission hot spots that exert disproportionately large adverse health effects on the population and surrounding environment, owing to their high population density and concentrated emission sources. Exceedances of ozone air quality standards are a problem in many urban areas. Improvements in the modelling of ozone precursors would benefit our understanding of the impact of changes in emissions and the effect of future legislation on air quality. As many VOCs are extremely reactive in the atmosphere and have high ozone forming potential, improved speciation of VOCs in models could lead to better predictions of ozone levels and secondary organic aerosol formation. Previously, VOC and carbon monoxide (CO) data from urban areas around the world were compared. Significant differences in VOC concentrations were observed, however, when normalized to CO, the VOC-CO ratios were similar for many locations and over time, even as emission reductions were implemented. The largest variation was found in the lighter alkanes due to the use of alternative transportation fuels in various world regions. These ratios were grouped by region and used to develop a new speciation for surface emissions of VOCs, by applying the regional observed VOC-CO ratios to the CO emissions for the urban areas. Urban areas were defined as 150 inhabitants per km2 or greater. Model simulations were performed using the MOZART-4 chemistry transport model to assess the improved speciation of the VOC emissions. The model outputs were compared to urban observational data where available. The impact of the new speciation of the distribution of CO, OH and ozone at the global scale will be

  6. SUBSTRATE EFFECTS ON VOC EMISSIONS FROM A LATEX PAINT

    Science.gov (United States)

    The effects of two substrates -- a stainless steel plate and a gypsum board -- on the volatile organic compound (VOC) emissions from a latex paint were evaluated by environmental chamber tests. It was found that the amount of VOCs emitted from the painted stainless steel was 2 to...

  7. Quantification of Methane and VOC Emissions from Natural Gas Production in Two Basins with High Ozone Events

    Science.gov (United States)

    Edie, R.; Robertson, A.; Snare, D.; Soltis, J.; Field, R. A.; Murphy, S. M.

    2015-12-01

    Since 2005, the Uintah Basin of Utah and the Upper Green River Basin of Wyoming frequently exceeded the EPA 8-hour allowable ozone level of 75 ppb, spurring interest in volatile organic compounds (VOCs) emitted during oil and gas production. Debate continues over which stage of production (drilling, flowback, normal production, transmission, etc.) is the most prevalent VOC source. In this study, we quantify emissions from normal production on well pads by using the EPA-developed Other Test Method 33a. This methodology combines ground-based measurements of fugitive emissions with 3-D wind data to calculate the methane and VOC emission fluxes from a point source. VOC fluxes are traditionally estimated by gathering a canister of air during a methane flux measurement. The methane:VOC ratio of this canister is determined at a later time in the laboratory, and applied to the known methane flux. The University of Wyoming Mobile Laboratory platform is equipped with a Picarro methane analyzer and an Ionicon Proton Transfer Reaction-Time of Flight-Mass Spectrometer, which provide real-time methane and VOC data for each well pad. This independent measurement of methane and VOCs in situ reveals multiple emission sources on one well pad, with varying methane:VOC ratios. Well pad emission estimates of methane, benzene, toluene and xylene for the two basins will be presented. The different emission source VOC profiles and the limitations of real-time and traditional VOC measurement methods will also be discussed.

  8. VOC emissions, evolutions and contributions to SOA formation at a receptor site in Eastern China

    Directory of Open Access Journals (Sweden)

    B. Yuan

    2013-03-01

    Full Text Available Volatile organic compounds (VOCs were measured by two online instruments (GC-FID/MS and PTR-MS at a receptor site on Changdao Island (37.99° N, 120.70° E in eastern China. Reaction with OH radical dominated the chemical loss of most VOC species during the Changdao campaign. A photochemical age based parameterization method is used to calculate VOC emission ratios and to quantify the evolution of ambient VOCs. The calculated emission ratios of most hydrocarbons agree well with those obtained from emission inventory, but the emission ratios of oxygenated VOCs (OVOCs are significantly lower than those from emission inventory. The photochemical age based parameterization method is also used to investigate primary emissions and secondary formation of organic aerosol. The primary emission ratio of OA to CO are determined to be 14.9 μg m−3 ppm−1 and SOA are produced at an enhancement ratio of 18.8 μg m−3 ppm−1 to CO after 50 h of photochemical processing in the atmosphere. SOA formation is significantly higher than the level determined from VOC oxidation under both high-NOx (2.0 μg m−3 ppm−1 CO and low-NOx condition (6.5 μg m−3 ppm−1 CO. Polycyclic aromatic hydrocarbons (PAHs and higher alkanes (>C10 account for as high as 17.4% of SOA formation, which suggests semi-volatile organic compounds (SVOCs may be a large contributor to SOA formation during the Changdao campaign. SOA formation potential of primary VOC emissions determined from both field campaigns and emission inventory in China are lower than the measured SOA levels reported in Beijing and Pearl River Delta (PRD, indicating SOA formation cannot be explained by VOC oxidation in this regions. SOA budget in China is estimated to be 5.0–13.7 Tg yr−1, with a fraction of at least 2.7 Tg yr−1 from anthropogenic emissions, which are much higher than the previous estimates from regional models.

  9. A mass transfer model for VOC emission from silage

    Science.gov (United States)

    Hafner, Sasha D.; Montes, Felipe; Rotz, C. Alan

    2012-07-01

    Silage has been shown to be an important source of emissions of volatile organic compounds (VOCs), which contribute to the formation of ground-level ozone. Measurements have shown that environmental conditions and silage properties strongly influence emission rates, making it difficult to assess the contribution of silage in VOC emission inventories. In this work, we present an analytical convection-diffusion-dispersion model for predicting emission of VOCs from silage. It was necessary to incorporate empirical relationships from wind tunnel trials for the response of mass transfer parameters to surface air velocity and silage porosity. The resulting model was able to accurately predict the effect of temperature on ethanol emission in wind tunnel trials, but it over-predicted alcohol and aldehyde emission measured using a mass balance approach from corn silage samples outdoors and within barns. Mass balance results confirmed that emission is related to gas-phase porosity, but the response to air speed was not clear, which was contrary to wind tunnel results. Mass balance results indicate that alcohol emission from loose silage on farms may approach 50% of the initial mass over six hours, while relative losses of acetaldehyde will be greater.

  10. Light dependency of VOC emissions from selected Mediterranean plant species

    Science.gov (United States)

    Owen, S. M.; Harley, P.; Guenther, A.; Hewitt, C. N.

    The light, temperature and stomatal conductance dependencies of volatile organic compound (VOC) emissions from ten plant species commonly found in the Mediterranean region were studied using a fully controlled leaf cuvette in the laboratory. At standard conditions of temperature and light (30°C and 1000 μmol m -2 s -1 PAR), low emitting species ( Arbutus unedo, Pinus halepensis, Cistus incanus, Cistus salvifolius, Rosmarinus officinalis and Thymus vulgaris) emitted between 0.1 and 5.0 μg (C) (total VOCs) g -1 dw h -1, a medium emitter ( Pinus pinea) emitted between 5 and 10 μg (C) g -1 dw h -1 and high emitters ( Cistus monspeliensis, Lavendula stoechas and Quercus sp.) emitted more than 10 μg (C) g -1 dw h -1. VOC emissions from all of the plant species investigated showed some degree of light dependency, which was distinguishable from temperature dependency. Emissions of all compounds from Quercus sp. were light dependent. Ocimene was one of several monoterpene compounds emitted by P. pinea and was strongly correlated to light. Only a fraction of monoterpene emissions from C. incanus exhibited apparent weak light dependency but emissions from this plant species were strongly correlated to temperature. Data presented here are consistent with past studies, which show that emissions are independent of stomatal conductance. These results may allow more accurate predictions of monoterpene emission fluxes from the Mediterranean region to be made.

  11. Volatile organic compound (VOC) emissions during malting and beer manufacture

    Science.gov (United States)

    Gibson, Nigel B.; Costigan, Gavin T.; Swannell, Richard P. J.; Woodfield, Michael J.

    Estimates have been made of the amounts of volatile organic compounds (VOCs) released during different stages of beer manufacture. The estimates are based on recent measurements and plant specification data supplied by manufacturers. Data were obtained for three main manufacturing processes (malting, wort processing and fermentation) for three commercial beer types. Some data on the speciation of emitted compounds have been obtained. Based on these measurements, an estimate of the total unabated VOC emission. from the U.K. brewing industry was calculated as 3.5 kta -1, over 95% of which was generated during barley malting. This value does not include any correction for air pollution control.

  12. Oxygenated VOC and monoterpene emissions from a boreal coniferous forest

    Science.gov (United States)

    Taipale, R.; Rantala, P.; Kajos, M. K.; Patokoski, J.; Ruuskanen, T. M.; Aalto, J.; Kolari, P.; Bäck, J.; Hari, P.; Kulmala, M.; Rinne, J.

    2012-04-01

    Compared with terpenoids, emissions of oxygenated volatile organic compounds (VOCs) from boreal ecosystems have been poorly characterized. We measured ecosystem scale emissions of three oxygenated compounds (methanol, acetaldehyde, and acetone) and monoterpenes from a Scots pine dominated forest in southern Finland during the summers 2006-2008. The measurements were conducted using the disjunct eddy covariance method combined with proton transfer reaction mass spectrometry. The contribution of the three oxygenated compounds to the measured total emissions was 40-60 %. The highest oxygenated VOC emissions were those of methanol, comprising 20-30 % of the total, followed by acetone with a share of 10-20 %. The acetaldehyde emissions were 5-10 % of the total. This emission composition will be compared with that obtained from shoot enclosure measurements. Methanol showed deposition during some periods although its overall flux was towards the atmosphere. The monoterpene emissions had a light dependent component, suggesting that part of the emissions originated directly from monoterpene biosynthesis. Diurnal, seasonal, and inter-annual variations in the emissions, along with temperature and light dependencies, will be discussed.

  13. Primary VOC emissions from Commercial Aircraft Jet Engines

    Science.gov (United States)

    Kilic, Dogushan; Huang, Rujin; Slowik, Jay; Brem, Benjamin; Durdina, Lukas; Rindlisbacher, Theo; Baltensperger, Urs; Prevot, Andre

    2014-05-01

    Air traffic is growing continuously [1]. The increasing number of airplanes leads to an increase of aviation emissions giving rise to environmental concerns globally by high altitude emissions and, locally on air quality at the ground level [2]. The overall impact of aviation emissions on the environment is likely to increase when the growing air transportation trend [2] is considered. The Aviation Particle Regulatory Instrumentation Demonstration Experiment (APRIDE)-5 campaign took place at Zurich Airport in 2013. In this campaign, aircraft exhaust is sampled during engine acceptance tests after engine overhaul at the facilities of SR Technics. Direct sampling from the engine core is made possible due to the unique fixed installation of a retractable sampling probe and the use of a standardized sampling system designed for the new particulate matter regulation in development for aircraft engines. Many of the gas-phase aircraft emissions, e.g. CO2, NOX, CO, SO2, hydrocarbons, and volatile organic compounds (VOC) were detected by the instruments in use. This study, part of the APRIDE-5 campaign, focuses on the primary VOC emissions in order to produce emission factors of VOC species for varying engine operating conditions which are the surrogates for the flight cycles. Previously, aircraft plumes were sampled in order to quantify VOCs by a proton transfer reaction quadrupole mass spectrometer (PTR-MS) [3]. This earlier study provided a preliminary knowledge on the emission of species such as methanol, acetaldehyde, acetone, benzene and toluene by varying engine thrust levels. The new setup was (i) designed to sample from the diluted engine exhaust and the new tool and (ii) used a high resolution time of flight PTR-MS with higher accuracy for many new species, therefore providing a more detailed and accurate inventory. We will present the emission factors for species that were quantified previously, as well as for many additional VOCs detected during the campaign

  14. Determination of VOC emission rates and compositions for offset printing.

    Science.gov (United States)

    Wadden, R A; Scheff, P A; Franke, J E; Conroy, L M; Keil, C B

    1995-07-01

    The release rates of volatile organic compounds (VOC) as fugitive emissions from offset printing are difficult to quantify, and the compositions are usually not known. Tests were conducted at three offset printing shops that varied in size and by process. In each case, the building shell served as the test "enclosure," and air flow and concentration measurements were made at each air entry and exit point. Emission rates and VOC composition were determined during production for (1) a small shop containing three sheetfed presses and two spirit duplicators (36,700 sheets, 47,240 envelopes and letterheads), (2) a medium-size industrial in-house shop with two webfed and three sheetfed presses, and one spirit duplicator (315,130 total sheets), and (3) one print room of a large commercial concern containing three webfed, heatset operations (1.16 x 10(6) ft) served by catalytic air pollution control devices. Each test consisted of 12 one-hour periods over two days. Air samples were collected simultaneously during each period at 7-14 specified locations within each space. The samples were analyzed by gas chromatography (GC) for total VOC and for 13-19 individual organics. Samples of solvents used at each shop were also analyzed by GC. Average VOC emission rates were 4.7-6.1 kg/day for the small sheetfed printing shop, 0.4-0.9 kg/day for the industrial shop, and 79-82 kg/day for the commercial print room. Emission compositions were similar and included benzene, toluene, xylenes, ethylbenzene, and hexane. Comparison of the emission rates with mass balance estimates based on solvent usage and composition were quite consistent.(ABSTRACT TRUNCATED AT 250 WORDS)

  15. Development of biogenic VOC emission inventories for the boreal forest

    Energy Technology Data Exchange (ETDEWEB)

    Tarvainen, V.

    2008-07-01

    The volatile organic compounds (VOCs) emitted by vegetation, especially forests, can affect local and regional atmospheric photochemistry through their reactions with atmospheric oxidants. Their reaction products may also participate in the formation and growth of new particles which affect the radiation balance of the atmosphere, and thus climate, by scattering and absorbing shortwave and longwave radiation and by modifying the radiative properties, amount and lifetime of clouds. Globally, anthropogenic VOC emissions are far surpassed by the biogenic ones, making biogenic emission inventories an integral element in the development of efficient air quality and climate strategies. The inventories are typically constructed based on landcover information, measured emissions of different plants or vegetation types, and empirical dependencies of the emissions on environmental variables such as temperature and light. This thesis is focused on the VOC emissions from the boreal forest, the largest terrestrial biome with characteristic vegetation patterns and strong seasonality. The isoprene, monoterpene and sesquiterpene emissions of the most prevalent boreal tree species in Finland, Scots pine, have been measured and their seasonal variation and dependence on temperature and light have been studied. The measured emission data and other available observations of the emissions of the principal boreal trees have been used in a biogenic emission model developed for the boreal forests in Finland. The model utilizes satellite landcover information, Finnish forest classification and hourly meteorological data to calculate isoprene, monoterpene, sesquiterpene and other VOC emissions over the growing season. The principal compounds emitted by Scots pine are DELTA3-carene and alpha-pinene in the south boreal zone and alpha- and beta-pinene in the north boreal zone. The monoterpene emissions are dependent on temperature and have a clear seasonal cycle with high emissions in spring

  16. Emissions of Volatile Organic Compounds (VOCs) from Animal Husbandry: Chemical Compositions, Separation of Sources and Animal Types

    Science.gov (United States)

    Yuan, B.; Coggon, M.; Koss, A.; Warneke, C.; Eilerman, S. J.; Neuman, J. A.; Peischl, J.; Aikin, K. C.; Ryerson, T. B.; De Gouw, J. A.

    2016-12-01

    Concentrated animal feeding operations (CAFOs) are important sources of volatile organic compounds (VOCs) in the atmosphere. We used a hydronium ion time-of-flight chemical ionization mass spectrometer (H3O+ ToF-CIMS) to measure VOC emissions from CAFOs in the Northern Front Range of Colorado during an aircraft campaign (SONGNEX) for regional contributions and from a mobile laboratory sampling for chemical characterizations of individual animal feedlots. The main VOCs emitted from CAFOs include carboxylic acids, alcohols, carbonyls, phenolic species, sulfur- and nitrogen-containing species. Alcohols and carboxylic acids dominate VOC concentrations. Sulfur-containing and phenolic species become more important in terms of odor activity values and NO3 reactivity, respectively. The high time-resolution mobile measurements allow the separation of the sources of VOCs from different parts of the operations occurring within the facilities. We show that the increase of ethanol concentrations were primarily associated with feed storage and handling. We apply a multivariate regression analysis using NH3 and ethanol as tracers to attribute the relative importance of animal-related emissions (animal exhalation and waste) and feed-related emissions (feed storage and handling) for different VOC species. Feed storage and handling contribute significantly to emissions of alcohols, carbonyls and carboxylic acids. Phenolic species and nitrogen-containing species are predominantly associated with animals and their waste. VOC ratios can be potentially used as indicators for the separation of emissions from dairy and beef cattle from the regional aircraft measurements.

  17. Behavior of VOCs and carbonyl compounds emission from different types of wallpapers in Korea.

    Science.gov (United States)

    Lim, Jungyun; Kim, Suejin; Kim, Arong; Lee, Wooseok; Han, Jinseok; Cha, Jun-Seok

    2014-04-17

    Emissions of volatile organic compounds (VOCs) and carbonyls from three types of commercially available wallpapers (i.e., PVC-coated, paper-backed, natural material-coated) in Korea were evaluated using a 20 L small chamber. A total of 332 products were tested for emission factors, frequencies of occurrence and composition ratios. Toluene and formaldehyde concentrations were below Korean standard values for all products; however, the total VOC (TVOC) concentrations exceeded current standards (4.0 mg/m²·h) for 30 products. The TVOC emission factor for PVC-coated wallpapers, for which polymer materials are used in the manufacturing process, was seven and 16 times higher than those of paper-backed and natural material-coated wallpapers, respectively. The detection frequencies for toluene and formaldehyde were the highest (82.5%) and fourth highest (79.5%), respectively among the 50 target chemical species. The composition ratios for BTEX ranged from 0.3% to 5.1% and unidentified VOCs, which were not qualitatively analyzed using standard gas methods, ranged from 90.2% to 94.8%. Among six carbonyl compounds (acrolein was not detected in any type of wallpaper), acetone had the highest concentrations in PVC-coated (44.6%) and paper-backed (66.6%) wallpapers. Formaldehyde emissions were highest (64.6%) for natural material-coated wallpapers, a result of the formaldehyde-based resin used in the manufacturing process for these products.

  18. Preliminary insights into the chemical composition and emissions of urban VOCs in the East Mediterranean

    Science.gov (United States)

    Sauvage, S.; Borbon, A.; Afif, C.; Bechara, J.; Leonardis, T.; Fronval, I.; Waked, A.; Brioude, J.; Locoge, N.

    2011-12-01

    The Mediterranean region is an area where polluted air masses coming from Eastern and Central Europe increase air pollution, particularly during stagnation periods, together with intense solar radiation. It was demonstrated that the eastern coast of the Mediterranean Sea suffers from this kind of phenomena. Favorable weather conditions, remote sources, high urban and biogenic emissions lead to the formation of secondary pollutants (ozone and secondary organic aerosols, SOA), which may have significant impacts on health and climate. However, data are sparse in this region. The ECOCEM (Emission and Chemistry of Organic Carbon in the East Mediterranean - Beirut) project aims to improve our understanding of air pollution in this area by studying the composition of the gaseous and particulate phases in Beirut (Lebanon). Beirut is located on the eastern border of the Mediterranean basin. The goal of the project, which is taking place over two intensive field campaigns (July 2011 and February 2012), is to provide valuable observations on the composition and the temporal evolution of organics (summer versus winter),to identify and quantify the relative importance of sources of volatile organic compounds (VOCs) and aerosols (SOA) and to study the role of VOCs in the first oxidation steps of SOA formation. For that purpose, a large suite of primary and secondary VOCs (>60) were measured during the summertime campaign (July 2nd to July 17th 2011) at one suburban site in Beirut. Techniques encompass off-line sampling on carbonaceous sorbent tubes (2-hour time resolution) and liquid coil scrubbing (1-hour time resolution), an on-line GCFID (1-hour time resolution) and a PTR-MS (4-min time resolution). We will discuss here the atmospheric composition of VOCs in relation with their emissions. In particular, these data provide useful constraints to evaluate the first temporally and spatially resolved national emission inventory that was built for the year 2010. Preliminary results

  19. Emission inventory of evaporative emissions of VOCs in four metro cities in India.

    Science.gov (United States)

    Srivastava, Anjali; née Som Majumdar, Dipanjali

    2010-01-01

    High concentrations of volatile organic compounds (VOCs) in ambient air of urban areas stress the need for the control of VOC emissions due to the toxic and carcinogenic nature of many VOCs commonly encountered in urban air. Emission inventories are an essential tool in the management of local air quality, which provide a listing of sources of air pollutant emissions within a specific area over a specified period of time. This study intended to provide a level IV emission inventory as par the United States Environmental Protection Agency (USEPA) definition for evaporative VOC emissions in the metro cities of India namely Delhi, Mumbai, Chennai, and Kolkata. The vehicular evaporative emissions are found to be the largest contributor to the total evaporative emissions of hydrocarbons followed by evaporative losses related to petrol loading and unloading activities. Besides vehicle-related activities, other major sources contributing to evaporative emissions of hydrocarbons are surface coating, dry cleaning, graphical art applications, printing (newspaper and computer), and the use of consumer products. Various specific preventive measures are also recommended for reducing the emissions.

  20. VOC characteristics, emissions and contributions to SOA formation during hazy episodes

    Science.gov (United States)

    Sun, Jie; Wu, Fangkun; Hu, Bo; Tang, Guiqian; Zhang, Junke; Wang, Yuesi

    2016-09-01

    Volatile organic compounds (VOC) are important precursors of secondary organic aerosols (SOA). The pollution processes in Beijing were investigated from 18th October to 6th November 2013 to study the characteristics, SOA formation potential and contributing factors of VOC during hazy episodes. The mean concentrations of VOC were 67.4 ± 33.3 μg m-3 on clear days and have 5-7-fold increase in polluted periods. VOC concentrations rapidly increased at a visibility range of 4-5 km with the rate of 25%/km in alkanes, alkenes and halocarbons and the rate of 45%/km in aromatics. Analysis of the mixing layer height (MLH); wind speed and ratios of benzene/toluene (B/T), ethylbenzene/m,p-xylene (E/X), and isopentane/n-pentane (i/n) under different visibility conditions revealed that the MLH and wind speed were the 2 major factors affecting the variability of VOC during clear days and that local emissions and photochemical reactions were main causes of VOC variation on polluted days. Combined with the fractional aerosol coefficient (FAC) method, the SOA formation potentials of alkanes, alkenes and aromatics were 0.3 ± 0.2 μg m-3, 1.1 ± 1.0 μg m-3 and 6.5 ± 6.4 μg m-3, respectively. As the visibility deteriorated, the SOA formation potential increased from 2.1 μg m-3 to 13.2 μg m-3, and the fraction of SOA-forming aromatics rapidly increased from 56.3% to 90.1%. Initial sources were resolved by a positive matrix factorization (PMF) model. Vehicle-related emissions were an important source of VOC at all visibility ranges, accounting for 23%-32%. As visibility declined, emissions from solvents and the chemical industry increased from 13.2% and 6.3% to 34.2% and 23.0%, respectively. Solvents had the greatest SOA formation ability, accounting for 52.5% on average on hazy days, followed by vehicle-related emissions (20.7%).

  1. VOC emission rates and emission factors for a sheetfed offset printing shop.

    Science.gov (United States)

    Wadden, R A; Scheff, P A; Franke, J E; Conroy, L M; Javor, M; Keil, C B; Milz, S A

    1995-04-01

    Emission rates were determined during production for a sheetfed offset printing shop by combining the measured concentrations and ventilation rates with mass balance models that characterized the printing space. Air samples were collected simultaneously on charcoal tubes for 12 separate 1-hour periods at 6 locations. Air samples and cleaning solvents were analyzed by gas chromatography for total volatile organic compounds (VOC) and 13 hydrocarbons. The average VOC emission rate was 470 g/hr with a range of 160-1100 g/hr. These values were in good agreement with the amounts of VOC, hexane, toluene, and aromatic C9s determined from estimated solvent usage and measured solvent compositions. Comparison of the emission rates with source activities indicated an emission factor of 30-51 g VOC/press cleaning. Based on the test observations it was estimated that this typical small printing facility was likely to release 1-2 T VOC/year. The methodology also may be useful for the surface coating industry, as emission rates in this study were determined without recourse to a temporary total enclosure and without interfering with worker activities, increasing worker exposure, or increasing safety and explosion hazards.

  2. Mechanisms of Increased Particle and VOC Emissions during DPF Active Regeneration and Practical Emissions Considering Regeneration.

    Science.gov (United States)

    Yamada, Hiroyuki; Inomata, Satoshi; Tanimoto, Hiroshi

    2017-02-27

    Mechanisms involved in increased particle and volatile organic compound (VOC) emissions during active and parked active regenerations of a diesel particulate filter (DPF) were investigated using heavy-duty trucks equipped with both a urea selective catalytic reduction system and a DPF (SCR + DPF) and a DPF-only. Particle emissions increased in the later part of the regeneration period but the mechanisms were different above and below 23 nm. Particles above 23 nm were emitted due to the lower filtering efficiency of the DPF because of the decreasing amount of soot trapped during regeneration. Small particles below 23 nm were thought to be mainly sulfuric acid particles produced from SO2 trapped by the catalyst, being released and oxidized during regeneration. Contrary to the particle emissions, VOCs increased in the earlier part of the regeneration period. The mean molecular weights of the VOCs increased gradually as the regeneration proceeded. To evaluate "practical emissions" in which increased emissions during the regeneration were considered, a Regeneration Correction Factor (RCF), which is the average emission during one cycle of regeneration/emission in normal operation, was adopted. The RCFs of PM and VOCs were 1.1-1.5, and those of PNs were as high as 3-140, although they were estimated from a limited number of observations.

  3. 40 CFR 60.502 - Standard for Volatile Organic Compound (VOC) emissions from bulk gasoline terminals.

    Science.gov (United States)

    2010-07-01

    ... (VOC) emissions from bulk gasoline terminals. 60.502 Section 60.502 Protection of Environment... SOURCES Standards of Performance for Bulk Gasoline Terminals § 60.502 Standard for Volatile Organic Compound (VOC) emissions from bulk gasoline terminals. On and after the date on which § 60.8(a) requires a...

  4. Study on characteristics of double surface VOC emissions from dry flat-plate building materials

    Institute of Scientific and Technical Information of China (English)

    WANG Xinke; ZHANG Yinping; ZHAO Rongyi

    2006-01-01

    This paper sets up an analytic model of double surface emission of volatile organic compound (VOC) from dry, flat-plate building materials. Based on it, the influence of factors including air change rate, loading factor of materials in the room, mass diffusion coefficient, partition coefficient, convective mass transfer coefficient, thickness of materials, asymmetric convective flow and initial VOC concentration distribution in the building material on emission is discussed. The conditions for simplifying double surface emission into single surface emission are also discussed. The model is helpful to assess the double surface VOC emission from flat-plate building materials used in indoor furniture and space partition.

  5. Comparison of VOC and ammonia emissions from individual PVC materials, adhesives and from complete structures.

    Science.gov (United States)

    Järnström, H; Saarela, K; Kalliokoski, P; Pasanen, A-L

    2008-04-01

    Emission rates of volatile organic compounds (VOCs) and ammonia measured from six PVC materials and four adhesives in the laboratory were compared to the emission rates measured on site from complete structures. Significantly higher specific emission rates (SERs) were generally measured from the complete structures than from individual materials. There were large differences between different PVC materials in their permeability for VOCs originating from the underlying structure. Glycol ethers and esters from adhesives used in the installation contributed to the emissions from the PVC covered structure. Emissions of 2-ethylhexanol and TXIB (2,2,4-trimethyl-1,3-pentanediol diisobutyrate) were common. High ammonia SERs were measured from single adhesives but their contribution to the emissions from the complete structure did not appear as obvious as for VOCs. The results indicate that three factors affected the VOC emissions from the PVC flooring on a structure: 1) the permeability of the PVC product for VOCs, 2) the VOC emission from the adhesive used, and 3) the VOC emission from the backside of the PVC product.

  6. Quantitative assessment of industrial VOC emissions in China: Historical trend, spatial distribution, uncertainties, and projection

    Science.gov (United States)

    Zheng, Chenghang; Shen, Jiali; Zhang, Yongxin; Huang, Weiwei; Zhu, Xinbo; Wu, Xuecheng; Chen, Linghong; Gao, Xiang; Cen, Kefa

    2017-02-01

    The temporal trends of industrial volatile organic compound (VOC) emissions was comprehensively summarized for the 2011 to 2013 period, and the projections for 2020 to 2050 for China were set. The results demonstrate that industrial VOC emissions in China increased from 15.3 Tg in 2011 to 29.4 Tg in 2013 at an annual average growth rate of 38.3%. Guangdong (3.45 Tg), Shandong (2.85 Tg), and Jiangsu (2.62 Tg) were the three largest contributors collectively accounting for 30.4% of the national total emissions in 2013. The top three average industrial VOC emissions per square kilometer were Shanghai (247.2 ton/km2), Tianjin (62.8 ton/km2), and Beijing (38.4 ton/km2), which were 12-80 times of the average level in China. The data from the inventory indicate that the use of VOC-containing products, as well as the production and use of VOCs as raw materials, as well as for storage and transportation contributed 75.4%, 10.3%, 9.1%, and 5.2% of the total emissions, respectively. ArcGIS was used to display the remarkable spatial distribution variation by allocating the emission into 1 km × 1 km grid cells with a population as surrogate indexes. Combined with future economic development and population change, as well as implementation of policy and upgrade of control technologies, three scenarios (scenarios A, B, and C) were set to project industrial VOC emissions for the years 2020, 2030, and 2050, which present the industrial VOC emissions in different scenarios and the potential of reducing emissions. Finally, the result shows that the collaborative control policies considerably influenced industrial VOC emissions.

  7. Mapping methane sources and emissions over California from direct airborne flux and VOC source tracer measurements

    Science.gov (United States)

    Guha, A.; Misztal, P. K.; Peischl, J.; Karl, T.; Jonsson, H. H.; Woods, R. K.; Ryerson, T. B.; Goldstein, A. H.

    2013-12-01

    fluxes were obtained using the virtual disjunct eddy covariance method and from Wavelet Analysis along flight tracks flown in the mixed layer. Preliminary analysis of mixing ratio measurements indicate that high concentrations of CH4 occur consistently while flying above the Central Valley that are correlated to large enhancements of methanol which is an important dairy and livestock emissions tracer. The elevated CH4 mixing ratios along the eastern edge of the San Joaquin Valley highlight the contribution of topography and emissions transport to local ambient levels of CH4. Large enhancements of CH4, benzene and toluene are also observed while flying over the oil production facilities in western part of Kern county (state's top oil producing county, 10% of US production) suggesting the likelihood of fugitive emissions in the region. VOC tracer analysis is used to evaluate the source of high CH4 emissions encountered along the eastern edge of the central Sacramento valley where fugitive emissions from natural gas fields and cultivation of rice are likely sources. Plumes from biomass burning, landfills and refineries encountered during different flights are also investigated. Eddy covariance based CH4 flux estimates are derived for various sources and compared with ';bottom-up' inventory estimates to verify/validate the CA methane inventory for major sources.

  8. An analytical solution for VOCs emission from multiple sources/sinks in buildings

    Institute of Scientific and Technical Information of China (English)

    DENG BaoQing; YU Bo; Chang Nyung KIM

    2008-01-01

    An analytical solution is presented to describe the emission/sorption of volatile organic compounds (VOCs) from/on multiple single-layer materials coexisting in buildings. The diffusion of VOCs within each material is described by a transient diffusion equation. All diffusion equations are coupled with each other through the equation of mass conservation in the air. The analytical solution is validated by the experimental data in literature, Compared to the one-material case, the coexistence of multiple materials may decrease the emission rate of VOCs from each material. The smaller the diffusion coef-ficient is, the more the emission rate decreases. Whether a material is a source or a sink in the case of multiple materials coexisting is not affected by the diffusion coefficient. For the case of multiple mate-rials with different partition coefficients, a material with a high partition coefficient may become a sink. This may promote the emission of VOCs from other materials.

  9. Optimizing the emission inventory of volatile organic compounds (VOCs) based on network observations

    Science.gov (United States)

    Chen, Sheng-Po; Liu, Wen-Tzu; Ou-Yang, Chang-Feng; Chang, Julius S.; Wang, Jia-Lin

    2014-02-01

    Hourly observations of 56 non-methane hydrocarbons (NMHCs) performed by a network of photochemical assessment monitoring stations (PAMS) at 11 locations across Taiwan were used to evaluate 56 speciated emissions and the resulting simulations of an air quality model. Based on the PAMS observations at two urban sites, emission modification was made for the 56 PAMS species in the model. To further test the applicability of this emission correction approach, the same modified emissions were subject to seven different meteorological conditions and comparison with observations of all the 11 PAMS sites. Originally there was a minimum of only 8 of 56 species showed agreement with observations for the worst of the 11 PAMS sites and 28 of 56 species for the best site. With modified emissions, the number increased to 13-52 species across the 11 PAMS sites, demonstrating that the simple urban based correction procedure has broad applicability. When applying this modification of PAMS emissions to the simulations of other air quality gases, SO2 and NOx showed small changes compared with observations (-0.27% and -2.51%, respectively), while total VOC concentrations showed significant changes (+15.28%) as a result of the adjustment in VOC emissions (+26.7%). Although VOCs are the precursor of ozone, the relatively large changes in VOC did not seem to affect ozone formation to the similar extent, only resulting in the changes of average O3 by 2.9 ppb (+9.41%). It shows that although the emission modification improves individual VOC simulations, the performance in oxidant simulation is still largely unaltered. Although the original U.S. VOC emission profiles can capture the general features of ambient VOCs, further optimization of emissions may still be needed by referencing extensive observations, so that emissions can better fit domestic conditions and accuracy in model simulations can be improved.

  10. Extended Research on Detection of Deception Using Volatile Organic Compound (VOC) Emissions

    Energy Technology Data Exchange (ETDEWEB)

    Center for Human Reliability Studies

    2006-06-01

    A system that captures and analyzes volatile organic compound (VOC) emissions from skin surfaces may offer a viable alternative method to the polygraph instrument currently in use for detecting deception in U.S. government settings. Like the involuntary autonomic central nervous system response data gathered during polygraph testing, VOC emissions from the skin may provide data that can be used to detect stress caused by deception. Detecting VOCs, then, may present a noninvasive, non-intrusive method for observing, recording, and quantifying evidence of stress or emotional change.

  11. Investigation on Using SBS and Active Carbon Filler to Reduce the VOC Emission from Bituminous Materials

    Directory of Open Access Journals (Sweden)

    Peiqiang Cui

    2014-08-01

    Full Text Available Bituminous materials are playing a vital role in pavement design and the roofing industry because of outstanding properties. Unfortunately, bituminous materials will release volatile organic compounds (VOC, making them non-environmentally friendly. Therefore, technologies that can be used to decrease the VOC emission are urgently required. In this research, the VOC emission and material behaviors were analyzed and compared to investigate the possibility of adding styrene butadiene styrene (SBS and active carbon filler into bituminous materials to develop environmentally-friendly materials. Thermal gravimetric analysis-mass spectrometry (TG-MS and ultraviolet-visible spectroscopy testing (UV-Vis were employed to characterize the VOC emission process. Temperature sweep testing and frequency sweep testing were conducted to evaluate the rheological properties of bituminous materials. Research results indicated that the combined introduction of 4 wt% styrene butadiene styrene (SBS and 4 wt% active carbon filler cannot only significantly lower the VOC emission speed and amount, but also improve the deformation resistance behavior at a higher temperature. SBS and active carbon filler can be used to reduce the VOC emission form bituminous materials.

  12. Emissions of selected VOC from forests: First results on measurements needed for improvement and validation of emission models

    Science.gov (United States)

    Steigner, D.; Steinbrecher, R.; Rappenglück, B.; Gasche, R.; Hansel, A.; Graus, M.; Lindinger, Ch.

    2003-04-01

    Biogenic volatile organic compounds (BVOCs) play a crucial role in the formation of photo-oxidants and particles through the diverse BVOC degradation pathways. Yet, current estimations about temporal and spatial BVOC emissions, including the specific BVOC mix are rather vague. This project addresses this issue by: the determination of (a) BVOC net emission rates and (b) primary emissions of BVOCs from the trees and soils. Measurement campaigns were carried out at the Waldstein site in the Fichtelgebirge in 2001 and 2002. Primary emissions of isoprenoids from the soil and from twigs of Norway spruce (Picea abies [L.] Karst.) and stand fluxes of isoprenoids were quantified by means of REA-technique with in situ GC-FID analysis and GC-MS analysis in the laboratory. Moreover, REA-samples obtained by the system were analysed by a PTR-MS. A critical value when using the REA approach is the Businger-Oncley parameter b. For this canopy type a b value of 0.39 (threshold velocity w_o = 0.6) was determined. The PTR-MS data show clear diurnal variations of ambient air mixing ratios of VOC such as isoprene and monoterpenes, but also of oxygenated VOCs such as carbonyls and alcohols and methylvinylketone (MVK) and methacrolein (MAK), products from isoprene degradation. Four selected trees (Picea abies [L.] Karst.) were intensively screened for primary BVOC emission rates. Most abundant species are b-pinene/sabinene and camphene. They show typical diurnal patterns with high emissions during daytime. Soil emissions of NO reached 250 nmol N m-2 s-1 at soil temperatures (in 3 cm depth) of 13^oC and at a relative air humidity of 60%. Ambient air mixing ratios near the soil surface of NO reached values of up to 0.7 ppb. NO_2 and ozone mixing ratios varied between 0.1 to 1.5 ppb and 10 to 37 ppb, respectively. As expected nitrogen oxide emissions rates tend to increase with increasing surface temperature. Isoprenoid emission from the soil was low and in general near the detection limit

  13. VOC emissions during outdoor ship painting and health-risk assessment

    Science.gov (United States)

    Malherbe, Laure; Mandin, Corinne

    Painting of ship external surfaces in building or repair shipyards generates significant emissions of volatile organic compounds (VOC) to the atmosphere. Such emissions have not been specifically regulated so far. The purpose of our study is therefore to evaluate the quantities and as far as possible the nature of the emitted VOC, to characterize the dispersion of these chemicals in the atmosphere and to assess the exposure and resulting health risks for surrounding populations. This study is focused on VOC emitted during outdoor work involving use of paints and solvents. VOC emissions are diffuse, since they come from the whole painted surfaces. A methodology for quantifying them is developed and tested, using information provided by ALSTOM—Chantiers de l'Atlantique and data found in paint technical sheets. Its reliability is checked against emission values established by ALSTOM or found in literature. Then, for two particular situations, construction on one hand, repair on the other hand, atmospheric dispersion of total VOC is simulated to assess the long-term impact (characterized by the plume extension and the annual mean concentrations) of these compounds. Finally, a health-risk assessment based on the estimates is carried out to evaluate the risks by inhalation for people living near the site. Considering the presumed composition of paints and the available reference toxicological values, total VOC are entirely assimilated to toluene. In both examples (construction and repair) and in the current state of knowledge, the calculated risk is not of health concern. Several ways for taking this study further are proposed: a more exhaustive collection of data relative to VOC and other substances contained in paints, on-site measurement of VOC in the ambient air, characterization of diffuse emissions related to other activities, such as purging or welding, and other pollutants, like particles.

  14. Comparing the VOC emissions between air-dried and heat-treated Scots pine wood

    Science.gov (United States)

    Manninen, Anne-Marja; Pasanen, Pertti; Holopainen, Jarmo K.

    The emissions of volatile organic compounds (VOCs) from air-dried Scots pine wood and from heat-treated Scots pine wood were compared with GC-MS analysis. Air-dried wood blocks released about 8 times more total VOCs than heat-treated (24 h at 230°C) ones. Terpenes were clearly the main compound group in the air-dried wood samples, whereas aldehydes and carboxylic acids and their esters dominated in the heat-treated wood samples. Only 14 compounds out of 41 identified individual compounds were found in both wood samples indicating considerable changes in VOC emission profile during heat-treatment process. Of individual compounds α-pinene, 3-carene and hexanal were the most abundant ones in the air-dried wood. By contrast, in the heat-treated wood 2-furancarboxaldehyde, acetic acid and 2-propanone were the major compounds of VOC emission. Current emission results reveal that significant chemical changes have occurred, and volatile monoterpenes and other low-molecular-weight compounds have evaporated from the wood during the heat-treatment process when compared to air-dried wood. Major chemical changes detected in VOC emissions are explained by the thermal degradation and oxidation of main constituents in wood. The results suggest that if heat-treated wood is used in interior carpentry, emissions of monoterpenes are reduced compared to air-dried wood, but some irritating compounds might be released into indoor air.

  15. Characterizations of volatile organic compounds (VOCs) from vehicular emissions at roadside environment: The first comprehensive study in Northwestern China

    Science.gov (United States)

    Li, Bowei; Ho, Steven Sai Hang; Xue, Yonggang; Huang, Yu; Wang, Liqin; Cheng, Yan; Dai, Wenting; Zhong, Haobin; Cao, Junji; Lee, Shuncheng

    2017-07-01

    Vehicular emission (VE) is one of the important anthropogenic sources for ground-level volatile organic compounds (VOCs) in both urban and suburban areas. A first comprehensive campaign was conducted at an urban roadside in Xi'an, China in summer, 2016. A total of 57 VOCs, as known as critical surface ozone (O3) precursors, and other trace gases were measured simultaneously during the sampling period. Iso-pentane, a tracer of gasoline evaporation, was the most abundant VOC in the roadside samples, followed by isobutane and benzene, attributed to the largest composition (∼70%) of gasoline-fueled vehicles on the road. The molar ratio of toluene/benzene (T/B) in our study (0.36) is far lower than the range reported in other cities, indicating the stronger contributions from diesel emissions. The results of source apportionment achieved with positive matrix factorization (PMF) receptor model were highly consistent with the vehicles compositions, strongly evidenced that the precise characterization of the VE sources from those marker species. The degrees of individual compound contributed to O3 production were weighed by ozone formation potential (OFP). Propylene (20%), 1-butene (11%) and iso-pentane(10%) were the top three contributors at the roadside. The information of this study complements the VOCs database regarding to the VE sources in Northwestern China.

  16. CHARACTERIZATION AND REDUCTION OF FORMALDEHYDE EMISSIONS FROM A LOW-VOC LATEX PAINT

    Science.gov (United States)

    The paper discusses the measurment and analysis of the patterns of formaldehyde emission from a low volatile organic compound (VOC) latex paint applied to gypsum board, using small environmental chamber tests. The formaldehyde emissions resulted in sharp increase of chamber air...

  17. VOC emission from oil refinery and petrochemical wastewater treatment plant estimation

    Directory of Open Access Journals (Sweden)

    Mihajlović Marina A.

    2013-01-01

    Full Text Available The introduction of environmental legislation improvement for industrial producers in Serbia, notably the Integrated Pollution Prevention Control (IPPC license, will oblige the industrial producers to provide annual report on the pollutant emissions into the environment, as well as to pay certain environment fee. Wastewater treatment plant can be a significant source of volatile organic compounds (VOCs diffuse emissions, which are difficult to measure directly. In the near future reporting obligations might expend to benzene and other VOCs. This paper deals with gaseous emissions calculations from API separator based on the emission factors and the adequate software applications. The analyzed results show that the estimated emission values differ depending on the applied method. The VOC emissions have been estimated using US EPA and CONCAWE emissions factors. The calculated emissions range from 40 to 4500 tons/year for oil refinery WWTP of 2,000,000 m3/year. The calculations of benzene and toluene emissions have been performed using three methods: US EPA emission factors, WATER9, and Toxchem+ software. The calculated benzene and toluene emissions range from 5.5-60 and 0.7-20 tons/year, respectively. The highest emission values were obtained by the US EPA emission factors, while the lowest values were the result of Toxchem+ analysis. The sensitivity analysis of obtained results included the following parameters: flow, temperature, oil content, and the concentration of benzene and toluene in the effluent. Wide range of results indicates the need for their official interpretation for the conditions typical for Serbia, thus establishing adequate national emission factors for future utilization of the “polluter pays principle” on the VOC and benzene emissions.

  18. Determination of Summertime VOC Emission Rates from Produced Water Ponds in the Uintah Basin

    Science.gov (United States)

    Martin, R. S.; Woods, C.; Lyman, S.

    2013-12-01

    The observance of excess ozone concentrations in Utah's Uintah Basin over past several years has prompted several investigations into the extent and causes of the elevated ozone. Among these is the assessment of potential emissions of reactive VOCs. Evaporation ponds, used a remediation technique for treatment of contaminated production and other waters, are one potential source of significant VOC emissions and is estimated that there are around 160 such ponds within the Uintah Basin's oil and gas production areas. In June 2012 VOC emission rates for several reactive VOCs were derived for an evaporation facility consisting of a small inlet pond (≈0.03 acres) and two larger, serial ponds (≈4.3 acres each). The emission rates were determined over three sampling periods using an inverse modeling approach. Under this methodology, ambient VOC concentrations are determined at several downwind locations through whole-air collection into SUMMA canisters, followed by GC/MS quantification and compared with predicted concentrations using an EPA-approved dispersion model, AERMOD. The presumed emission rates used within the model were then adjusted until the modeled concentrations approach the observed concentrations. The derived emission rates for the individual VOCs were on the order of 10-3 g/s/m2 from the inlet pond and 10-6 g/s/m2 from the larger ponds. The emissions from the 1st pond in series after the inlet pond were about 3-4x the emissions from the 2nd pond. These combined emission rates are about an order of magnitude those reported for a single study in Colorado (Thoma, 2009). It should be noted, however, that the variability about each of the VOC emission rates was significant (often ×100% at the 95% confidence interval). Extrapolating these emission rates to the estimated total areas of all the evaporation ponds within Basin resulted in calculated Basin-wide VOC emissions 292,835 tons/yr. However, Bar-Ilan et al. (2009) estimated 2012 VOC oil and gas related

  19. Characteristics of volatile organic compounds (VOCs) from the evaporative emissions of modern passenger cars

    Science.gov (United States)

    Yue, Tingting; Yue, Xin; Chai, Fahe; Hu, Jingnan; Lai, Yitu; He, Liqang; Zhu, Rencheng

    2017-02-01

    Volatile organic compounds (VOCs) from vehicle evaporative emissions contribute substantially to photochemical air pollution. Yet, few studies of the characteristics of VOCs emitted from vehicle evaporative emissions have been published. We investigate the characteristics of 57 VOCs in hot soak, 24 h diurnal and 48 h diurnal emissions by applying the Sealed Housing Evaporative Determination unit (SHED) test to three modern passenger cars (one US Tier 2 and two China IV vehicles) using two different types of gasoline. The characteristics of the VOCs from the hot soak, 24 h diurnal and 48 h diurnal emissions were different due to their different emission mechanisms. In the hot soak emissions, toluene, isopentane/n-pentane, and 2,2,4-trimethylpentane were dominant species. In the 24 h and 48 h diurnal emissions, isopentane and n-pentane were dominant species. Toluene was the third most dominant component in the 24 h diurnal emissions but decreased by a mass of 42%-80% in the 48 h diurnal emissions. In the hot soak, 24 h diurnal and 48 h diurnal emissions, alkanes were generally the dominant hydrocarbons, followed by aromatics and olefins. However, owing to different evaporative emission mechanisms, the weight percentages of the aromatic hydrocarbons decreased and the weight percentages of the alkanes increased from the hot soak test to the 24 h diurnal and 48 h diurnal tests for each vehicle. The dominant contributors to the ozone formation potentials (OFPs) were also different in the hot soak, 24 h diurnal and 48 h diurnal emissions. The OFPs (g O3/g VOC) of the hot soak emissions were higher than those of the 24 h and 48 h diurnal emissions. In addition, the combined effect of decreasing the olefin and aromatic contents of gasoline on vehicle evaporative emissions was investigated. The aromatics all decreased substantially in the hot soak, 24 h and 48 h diurnal emissions, and the total masses of the VOCs and OFPs decreased, with the greatest reduction occurring in

  20. VOC emissions of smouldering combustion from Mediterranean wildfires in central Portugal

    Science.gov (United States)

    Evtyugina, Margarita; Calvo, Ana Isabel; Nunes, Teresa; Alves, Célia; Fernandes, Ana Patrícia; Tarelho, Luís; Vicente, Ana; Pio, Casimiro

    2013-01-01

    Emissions of trace gases and C5-C10 volatile organic compounds (VOCs) from Mediterranean wildfires occurring in Portugal in summer 2010 were studied. Fire smoke was collected in Tedlar bags and analysed for CO, CO2, total hydrocarbons (THC) and VOCs. The CO, CO2 and THC emission factors (EFs) were 206 ± 79, 1377 ± 142 and 8.1 ± 9 g kg-1 biomass burned (dry basis), respectively. VOC emissions from Mediterranean wildfires were reported for the first time. Aromatic hydrocarbons were major components of the identified VOC emissions. Among them, benzene and toluene were dominant compounds with EFs averaging 0.747 ± 0.303 and 0.567 ± 0.422 g kg-1 biomass burned (dry basis), respectively. Considerable amounts of oxygenated organic volatile compounds (OVOCs) and isoprenoids were detected. 2-Furaldehyde and hexanal were the most abundant measured OVOCs with EFs of 0.337 ± 0.259 and 0.088 ± 0.039 g kg-1 biomass burned (dry basis), respectively. The isoprenoid emissions were dominated by isoprene (EF = 0.207 ± 0.195 g kg-1 dry biomass burned) and α-pinene (EF = 0.112 ± 0.093 g kg-1 dry biomass burned). Emission data obtained in this work are useful for validating and improving emission inventories, as well for carrying out modelling studies to assess the effects of vegetation fires on air pollution and tropospheric chemistry.

  1. Control of VOC emissions from a flexographic printing facility using an industrial biotrickling filter.

    Science.gov (United States)

    Sempere, F; Martínez-Soria, V; Penya-Roja, J M; Waalkens, A; Gabaldón, C

    2012-01-01

    The study of an industrial unit of biotrickling filter for the treatment of the exhaust gases of a flexographic facility was investigated over a 2-year period with the objective to meet the volatile organic compound (VOC) regulatory emission limits. Increasing the water flow rate from 2 to 40 m(3) h(-1) improved the performance of the process, meeting the VOC regulation when 40 m(3) h(-1) were used. An empty bed residence time (EBRT) of 36 s was used when the inlet air temperature was 18.7 °C, and an EBRT as low as 26 s was set when the inlet temperature was 26.8 °C. During this long-term operation, the pressure drop over the column of the bioreactor was completely controlled avoiding clogging problems and the system could perfectly handle the non-working periods without VOC emission, demonstrating its robustness and feasibility to treat the emission of the flexographic sector.

  2. On-road emission characteristics of VOCs from light-duty gasoline vehicles in Beijing, China

    Science.gov (United States)

    Cao, Xinyue; Yao, Zhiliang; Shen, Xianbao; Ye, Yu; Jiang, Xi

    2016-01-01

    This study is the third in a series of three papers aimed at characterizing the VOC emissions of vehicles in Beijing. In this study, 30 light-duty vehicles fueled with gasoline were evaluated using a portable emission measurement system (PEMS) as they were driven on a predesigned, fixed test route. All of the tested vehicles were rented from private vehicle owners and spanned regulatory compliance guidelines ranging from Pre-China I to China IV. Alkanes, alkenes, aromatics and some additional species in the exhaust were collected in Tedlar bags and analyzed using gas chromatography/mass spectrometry (GC-MS). Carbonyls were collected on 2,4-dinitrophenyhydrazine (DNPH) cartridges and analyzed using high-performance liquid chromatography (HPLC). Overall, 74 VOC species were detected from the tested vehicles, including 22 alkanes, 6 alkenes, 1 alkyne, 16 aromatics, 3 cyclanes, 10 halohydrocarbons, 12 carbonyls and 4 other compounds. Alkanes, aromatics and carbonyls were the dominant VOCs with weight percentages of approximately 36.4%, 33.1% and 17.4%, respectively. The average VOC emission factors and standard deviations of the Pre-China I, China I, China II, China III and China IV vehicles were 469.3 ± 200.1, 80.7 ± 46.1, 56.8 ± 37.4, 25.6 ± 11.7 and 14.9 ± 8.2 mg/km, respectively, which indicated that the VOC emissions significantly decreased under stricter vehicular emission standards. Driving cycles also influenced the VOC emissions from the tested vehicles. The average VOC emission factors based on the travel distances of the tested vehicles under urban driving cycles were greater than those under highway driving cycles. In addition, we calculated the ozone formation potential (OFP) using the maximum incremental reactivity (MIR) method. The results of this study will be helpful for understanding the true emission levels of light-duty gasoline vehicles and will provide information for controlling VOC emissions from vehicles in Beijing, China.

  3. Consideration of the Change of Material Emission Signatures due to Longterm Emissions for Enhancing VOC Source Identification

    DEFF Research Database (Denmark)

    Han, K. H.; Zhang, J. S.; Knudsen, Henrik Nellemose

    2011-01-01

    The objectives of this study were to characterize the changes of VOC material emission profiles over time and develop a method to account for such changes in order to enhance a source identification technique that is based on the measurements of mixed air samples and the emission signatures of in...

  4. Consideration Of The Change Of Material Emission Signatures Due To Long-term Emissions For Enhancing Voc Source Identification

    DEFF Research Database (Denmark)

    Han, K. H.; Zhang, J. S.; Knudsen, H. N.

    2011-01-01

    The objectives of this study were to characterize the changes of VOC material emission profiles over time and develop a method to account for such changes in order to enhance a source identification technique that is based on the measurements of mixed air samples and the emission signatures of in...

  5. 国内外 VOCs 排放标准体系研究%Study of Emission Standards System of VOCs at Home and Abroad

    Institute of Scientific and Technical Information of China (English)

    罗斌; 蒋燕; 王斌

    2014-01-01

    It had important significance to develop VOCs emission standards for controlling VOCs emissions, improving air quality, and protecting human health and ecological environment. The characteristics of emission standards system of VOCs at home and abroad were analyzed, and some suggestions on the development of VOCs emission standards were proposed that toxicity and emissions of pollutants, particular pollutants of key industries should be considered when developing standards, and establishing emission standards system of VOCs giving priority to industry standards.%制定VOCs排放标准对于控制VOCs排放量,改善环境空气质量,保护人体健康和生态环境有重要意义。分析了国内外VOCs排放标准体系的特点,提出我国制定VOCs排放标准的几点建议,即标准制定过程中应考虑污染物毒性和排放量大小,考虑控制重点行业的特征污染物,并建立以行业排放标准为主的VOCs排放标准体系。

  6. CHARACTERIZATION OF LOW-VOC LATEX PAINTS: VOLATILE ORGANIC COMPOUND CONTENT, VOC AND ALDEHYDE EMISSIONS, AND PAINT PERFORMANCE

    Science.gov (United States)

    The report gives results of laboratory tests to evaluate commercially available latex paints advertised as "low-odor," "low-VOC (volatile organic compound)," or "no-VOC." Measurements were performed to quantify the total content of VOCs in the paints...

  7. Effect of heat waves on VOC emissions from vegetation and urban air quality

    Science.gov (United States)

    Churkina, G.; Kuik, F.; Lauer, A.; Bonn, B.; Butler, T. M.

    2015-12-01

    Programs to plant millions of trees in cities around the world aim at the reduction of summer temperatures, increase carbon storage, storm water control, provision of space for recreation, as well as poverty alleviation. Although these multiple benefits speak positively for urban greening programs, the programs do not take into account how close human and natural systems are coupled in urban areas. Elevated temperatures together with anthropogenic emissions of air and water pollutants distinguish the urban system. Urban and sub-urban vegetation responds to ambient changes and reacts with pollutants. Neglecting this coupling may lead to unforeseen drawbacks of urban greening programs. The potential for emissions of volatile organic compounds (VOC) from vegetation combined with anthropogenic emissions to produce ozone has long been recognized. This potential increases under rising temperatures. Here we investigate how heat waves affect emissions of VOC from urban vegetation and corresponding ground-level ozone. In this study we use Weather Research and Forecasting Model with coupled atmospheric chemistry (WRF-CHEM) to quantify these feedbacks in Berlin, Germany during the 2006 heat wave. VOC emissions from vegetation are simulated with MEGAN 2.0 coupled with WRF-CHEM. Our preliminary results indicate that contribution of VOCs from vegetation to ozone formation may increase by more than twofold during the heat wave period. We highlight the importance of the vegetation for urban areas under changing climate and discuss associated tradeoffs.

  8. VOC emission into the atmosphere by trees and leaf litter in Polish forests

    Science.gov (United States)

    Isidorov, V.; Smolewska, M.; Tyszkiewicz, Z.

    2009-04-01

    It is generally recognized at present that the vegetation of continents is the principal source of reactive volatile organic compounds (VOC) of the atmosphere. The upper limit of the evaluation of global phytogenic VOC is 1100-1500 Tg/yr (Isidorov, 1990; Guenther et al., 1995). Although these global evaluations showing the place of phytogenic emission among of other VOC sources are important, evaluations for individual countries are also very important. This poster represents the results of the estimation of VOC emission from Polish forests. Calculations took into account the composition and age of forests. According to our estimation, the total VOC emission by the arboreal vegetation differs from 190 to 750 kt/yr, depending of weather conditions in different years. There are only few studies conducted on decaying plant material as a source of atmospheric VOCs, but still they are able to give evidence of the importance of this source. For Polish forests, the litter mass is estimated to be (16-19)106 t/yr. These organic materials undergo decomposition by mesofauna and microorganisms. In these processes volatile organic compounds (VOC) stored in the litter and secondary metabolites of litter-destroying fungi are emitted into the atmosphere. The scale of the phenomenon makes leaf litter an important VOC source in the atmosphere. The filling of numerous gaps in researches of VOC emissions from decomposing leaf litter demands carrying out of long term field experiments in various climatic conditions. In this communication we report also the results of 3.5-year experiment on qualitative and quantitative GC-MS investigations of VOC emitted into the gas phase from leaves litter of some species of deciduous and coniferous trees of Polish forests. Apart from terpenes and their oxygenated derivatives, which are usual in plant tissues, leaf litter intensively emits vast amounts of lower alcohols and carbonyl compounds. We suppose that these volatile substances are products

  9. CAPSTONE REPORT ON THE DEVELOPMENT OF A STANDARD TEST METHOD FOR VOC EMISSIONS FROM INTERIOR LATEX PAINT AND ALKYD PAINTS

    Science.gov (United States)

    The report gives details of a small-chamber test method developed by the EPA for characterizing volatile organic compound (VOC) emissions from interior latex and alkyd paints. Current knowledge about VOC, including hazardous air pollutant, emissions from interior paints generated...

  10. Influence of way of finishing furniture segments on amount emissions VOCs

    Directory of Open Access Journals (Sweden)

    Petr Čech

    2010-01-01

    Full Text Available The study deals with the influence of way of finishing furniture segments on amount emissions VOCs (volatile organic compounds. The so-called Volatile Organic Compounds (VOC are among the largest pollution sources of both the internal and external environments.VOC is defined as emission of any organic compound or a mixture thereof, with the exception of methane, whereby the compound exerts the pressure of 0.01 kPa or more at the temperature of 20 °C (293.15 K and reaches the corresponding volatility under the specific conditions of its use and can undergo photochemical reactions with nitrogen oxides when exposed to solar radiation. The effects of VOC upon environment can be described by equation: VOC + NOx + UV radiation + heat = tropospheric ozone (O3In this work there were tested MDF (medium density fibreboard coated by resin impregnated paper was used for the furniture components’ production. Next were tested compressed wood, which was used as a second material of furniture components. These both chosen materials was covered by resin impregnated paper and than sequentially finished by regular coat of finish.An attention of this study is especially put on mentioned factors and on quantity of instant and long-term VOCs emissions emitted from furniture components.The amount of emissions from furniture components, in different phases of the preparation including the resin impregnated paper coating finish, was monitored within the time intervals of 24 hours and 720 hours starting after the time of the finish preparation.The MDF (medium density fibreboard coated by resin impregnated paper was used for the furniture components´ production.A compressed wood was used as a second material of furniture components. This alternative material was covered by resin impregnated paper and than sequentially finished by regular coat of finish.

  11. Investigations of the ratios of stable carbon isotopes in atmospheric relevant VOC using simulation and field experiments; Untersuchungen der Verhaeltnisse stabiler Kohlenstoffisotope in atmosphaerisch relevanten VOC in Simulations- und Feldexperimenten

    Energy Technology Data Exchange (ETDEWEB)

    Spahn, Holger

    2010-07-01

    Volatile organic compounds (VOC) play an important role in the regional and global atmospheric chemistry. The author of the contribution under consideration reports on the analysis of the ratios of stable carbon isotopes ({delta}({sup 13}C) analysis) in atmospheric VOCs. At first, the state of the art of this analytical technique is described. For the first time {delta}({sup 13}C) values of different monoterpenes have been determined in the investigation of vegetable emissions at a plant chamber. By means of the oxidation of {beta}-pinene by ozone in an aerosol chamber, the kinetic isotope effect of this reaction was determined. In southern Germany, air samples for the {delta}({sup 13}C) analysis were collected using a zeppelin. This enables a height-resolved measurement of {delta}({sup 13}C) values. Based on these measurements, the average photochemical age for methanol, toluene and p-xylene at different heights was calculated.

  12. Effects of cold temperature and ethanol content on VOC emissions from light-duty gasoline vehicles

    Science.gov (United States)

    Emissions of speciated volatile organic compounds (VOCs), including mobile source air toxics (MSATs), were measured in vehicle exhaust from three light-duty spark ignition vehicles operating on summer and winter grade gasoline (E0) and ethanol blended (E10 and E85) fuels. Vehicle...

  13. ECOS E-MATRIX Methane and Volatile Organic Carbon (VOC) Emissions Best Practices Database

    Energy Technology Data Exchange (ETDEWEB)

    Parisien, Lia [The Environmental Council Of The States, Washington, DC (United States)

    2016-01-31

    This final scientific/technical report on the ECOS e-MATRIX Methane and Volatile Organic Carbon (VOC) Emissions Best Practices Database provides a disclaimer and acknowledgement, table of contents, executive summary, description of project activities, and briefing/technical presentation link.

  14. Feasibility Analysis of Sustainability-Based Measures to Reduce VOC Emissions in Office Partition Manufacturing

    Directory of Open Access Journals (Sweden)

    Marc A. Rosen

    2010-02-01

    Full Text Available A feasibility analysis is reported of reduction opportunities for volatile organic compound (VOC emissions in manufacturing office furniture partitions, aimed at contributing to efforts to improve the sustainability of the process. A pollution prevention methodology is utilized. The purpose is to provide practical options for VOC emissions reductions during the manufacturing of office furniture partitions, but the concepts can be generally applied to the wood furniture industry. Baseline VOC emissions for a typical plant are estimated using a mass balance approach. The feasibility analysis expands on a preliminary screening to identify viable pollution prevention options using realistic criteria and weightings, and is based on technical, environmental and economic considerations. The measures deemed feasible include the implementation of several best management practices, ceasing the painting of non-visible parts, switching to hot melt backwrapping glue, application of solvent recycling and modification of the mechanical clip attachment. Implementation, measurement and control plans are discussed for the measures considered feasible, which can enhance the sustainability of the manufacturing of office furniture partitions. Reducing VOC emissions using the measures identified can, in conjunction with other measures, improve the sustainability of the manufacturing process.

  15. Effects of cold temperature and ethanol content on VOC emissions from light-duty gasoline vehicles

    Science.gov (United States)

    Emissions of speciated volatile organic compounds (VOCs), including mobile source air toxics (MSATs), were measured in vehicle exhaust from three light-duty spark ignition vehicles operating on summer and winter grade gasoline (E0) and ethanol blended (E10 and E85) fuels. Vehicle...

  16. Volatile organic compounds (VOCs) emission characteristics and control strategies for a petrochemical industrial area in middle Taiwan.

    Science.gov (United States)

    Yen, Chia-Hsien; Horng, Jao-Jia

    2009-11-01

    This study investigated VOC emissions from the largest petrochemical industrial district in Taiwan and recommended some control measures to reduce VOC emissions. In addition to the petrochemical industry, the district encompasses a chemical and fiber industry, a plastics industry and a harbor, which together produce more than 95% of the VOC emissions in the area. The sequence of VOC emission was as follows: components (e.g., valves, flanges, and pumps) (47%) > tanks (29%) > stacks (15%) > wastewater treatment facility (6%) > loading (2%) > flares (1%). Other plants producing high-density polyethylene (HDPE), styrene, ethylene glycol (EG), gas oil, and iso-nonyl-alchol (INA) were measured to determine the VOC leaching in the district. The VOC emissions of these 35 plants (90% of all plants) were less than 100 tons/year. About 74% of the tanks were fixed-roof tanks that leached more VOCs than the other types of tanks. To reduce leaching, the components should be checked periodically, and companies should be required to follow the Taiwan EPA regulations. A VOC emission management system was developed in state implementation plans (SIPs) to inspect and reduce emissions in the industrial district.

  17. New observations of VOC emissions and concentrations in, above, and around the Central Valley of California

    Science.gov (United States)

    Goldstein, A. H.; Fares, S.; Gentner, D. R.; Park, J.; Weber, R.; Ormeno, E.; Holzinger, R.; Misztal, P. K.; Karl, T. R.; Guenther, A. B.; Fischer, M. L.; Harley, R. A.; Karlik, J. F.

    2011-12-01

    Large portions of the Central Valley of California are out of compliance with current state and federal air quality standards for ozone and particulate matter, and the relative importance of biogenic and anthropogenic VOC emissions to their photochemical production in this region remains uncertain. In 2009-2011 multiple measurement campaigns were completed investigating the VOC emission inventory and concentration distributions. In 2009 BVOC emissions from more than 20 species of major agricultural crops in California were measured in a greenhouse using branch enclosures by both PTRMS and in-situ GC. Overall, crops were found to emit low amounts of BVOC compared to the natural forests surrounding the valley. Crops mainly emitted methanol and terpenes, with a broad array of other species emitted at lower levels, and all the measured crops showed negligible emissions of isoprene. Navel oranges were the largest crop BVOC emitters measured so a full year of flux measurements were made in an orange grove near Visalia in 2010 by eddy covariance(EC)-PTRMS with two multi-week periods of concentration measurements by hourly in-situ GC, and one month of high mass resolution flux measurements by EC-PTR-TOF-MS. The dominant BVOC emissions from the orange grove were methanol and terpenes, followed by acetone, acetaldehyde, and a low level of emissions for many other species. In 2011 aircraft eddy covariance measurements of BVOC fluxes were made by EC-PTRMS covering a large area of California as part of the California Airborne Bvoc Emission Research in Natural Ecosystem Transects (CABERNET) campaign aimed at improving BVOC emission models on regional scales, mainly profiling BVOC emissions from oak woodlands surrounding the Central Valley. In 2010, hourly in-situ VOC measurements were made via in-situ GC in Bakersfield, CA as part of the CalNex experiment. Additionally, in-situ measurements of fresh motor vehicle exhaust were made in Oakland's Caldecott tunnel. Measurements by

  18. Comparison of the substrate effect on VOC emissions from water based varnish and latex paint.

    Science.gov (United States)

    Silva, Gabriela V; Vasconcelos, M Teresa S D; Santos, Armando M; Fernandes, Eduardo O

    2003-01-01

    The building materials are recognised to be major contributors to indoor air contamination by volatile organic compounds (VOCs). The improvement of the quality of the environment within buildings is a topic of increasing research and public interest. Legislation in preparation by the European Commission may induce, in the near future, European Union Member States to solicit the industries of paints, varnishes and flooring materials for taking measures, in order to reduce the VOC emissions resulting from the use of their products. Therefore, product characterisation and information about the influence of environmental parameters on the VOC emissions are fundamental for providing the basic scientific information required to allow architects, engineers, builders, and building owners to provide a healthy environment for building occupants. On the other hand, the producers of coating building materials require this information to introduce technological alterations, when necessary, in order to improve the ecological quality of their products, and to make them more competitive. Studies of VOC emissions from wet materials, like paints and varnishes, have usually been conducted after applying the material on inert substrates, due to its non-adsorption and non-porosity properties. However, in real indoor environments, these materials are applied on substrates of a different nature. One aim of this work was to study, for the first time, the VOC emissions from a latex paint applied on concrete. The influence of the substrate (uncoated cork parquet, eucalyptus parquet without finishing and pine parquet with finishing) on the emissions of VOC from a water-based varnish was also studied. For comparison purposes, polyester film (an inert substrate) was used for both wet materials. The specific emission rates of the major VOCs were monitored for the first 72 h of material exposure in the atmosphere of a standardized test chamber. The air samples were collected on Tenax TA and

  19. Eddy covariance VOC emission and deposition fluxes above grassland using PTR-TOF

    Directory of Open Access Journals (Sweden)

    T. M. Ruuskanen

    2010-09-01

    Full Text Available Eddy covariance (EC is the preferable technique for flux measurements since it is the only direct flux determination method. It requires a continuum of high time resolution measurements (e.g. 5–20 Hz. For volatile organic compounds (VOC soft ionization via proton transfer reaction has proven to be a quantitative method for real time mass spectrometry; here we use a proton transfer reaction time of flight mass spectrometer (PTR-TOF for 10 Hz EC measurements of full mass spectra up to m/z 315. The mass resolution of the PTR-TOF enabled the identification of chemical formulas and separation of oxygenated and hydrocarbon species exhibiting the same nominal mass. We determined 481 ion mass peaks from ambient air concentration above a managed, temperate mountain grassland in Neustift, Stubai Valley, Austria. During harvesting we found significant fluxes of 18 compounds distributed over 43 ions, including protonated parent compounds, as well as their isotopes and fragments and VOC-H+-water clusters. The dominant BVOC fluxes were methanol, acetaldehyde, ethanol, hexenal and other C6 leaf wound compounds, acetone, acetic acid, monoterpenes and sequiterpenes.

    The smallest reliable fluxes we determined were less than 0.1 nmol m−2 s−1, as in the case of sesquiterpene emissions from freshly cut grass. Terpenoids, including mono- and sesquiterpenes, were also deposited to the grassland before and after the harvesting. During cutting, total VOC emission fluxes up to 200 nmol C m−2 s−1 were measured. Methanol emissions accounted for half of the emissions of oxygenated VOCs and a third of the carbon of all measured VOC emissions during harvesting.

  20. Biogenic VOCs emission inventory development of temperate grassland vegetation in Xilin River Basin,Inner Mongolia,China

    Institute of Scientific and Technical Information of China (English)

    HE Nian-peng; HAN Xing-guo; SUN Wei; Pan Qing-min

    2004-01-01

    Given the key role of biogenic volatile organic compounds(VOCs) to tropospheric chemistry and regional air quality, it is important to generate accurate VOCs emission inventories. However, only a less fraction of plant species, in temperate grassland of Inner Mongolia, has been characterized by quantitative measurements. A taxonomic methodology, which assigns VOCs measurements to unmeasured species, is an applicable and inexpensive alternation for extensive VOCs emission survey, although data are needed for additional plant families and genera to further validate the taxonomic approach in grassland vegetation. In this experiment, VOCs emission rates of 178 plant species were measured with a portable photoionization detector(PID). The results showed the most of genera and some families have consistent feature of their VOCs emission, especially for isoprene, and provide the basic premise of taxonomic methodology to develop VOCs emission inventories for temperate grassland. Then, the taxonomic methodology was introduced into assigning emission rate to other 96 species, which no measured emission rates available here. A systematical emission inventory of temperate grassland vegetation in Inner Mongolia was provided and further evidence that taxonomy relationship can serve as a useful guide for generalizing the emissions behavior of many, but not all, plant families and genera to grassland vegetation.

  1. Response surface modeling-based source contribution analysis and VOC emission control policy assessment in a typical ozone-polluted urban Shunde, China.

    Science.gov (United States)

    You, Zhiqiang; Zhu, Yun; Jang, Carey; Wang, Shuxiao; Gao, Jian; Lin, Che-Jen; Li, Minhui; Zhu, Zhenghua; Wei, Hao; Yang, Wenwei

    2017-01-01

    To develop a sound ozone (O3) pollution control strategy, it is important to well understand and characterize the source contribution due to the complex chemical and physical formation processes of O3. Using the "Shunde" city as a pilot summer case study, we apply an innovative response surface modeling (RSM) methodology based on the Community Multi-Scale Air Quality (CMAQ) modeling simulations to identify the O3 regime and provide dynamic analysis of the precursor contributions to effectively assess the O3 impacts of volatile organic compound (VOC) control strategy. Our results show that Shunde is a typical VOC-limited urban O3 polluted city. The "Jiangmen" city, as the main upper wind area during July 2014, its VOCs and nitrogen oxides (NOx) emissions make up the largest contribution (9.06%). On the contrary, the contribution from local (Shunde) emission is lowest (6.35%) among the seven neighbor regions. The local VOCs industrial source emission has the largest contribution comparing to other precursor emission sectors in Shunde. The results of dynamic source contribution analysis further show that the local NOx control could slightly increase the ground O3 under low (10.00%) and medium (40.00%) reduction ratios, while it could start to turn positive to decrease ground O3 under the high NOx abatement ratio (75.00%). The real-time assessment of O3 impacts from VOCs control strategies in Pearl River Delta (PRD) shows that the joint regional VOCs emission control policy will effectively reduce the ground O3 concentration in Shunde. Copyright © 2016. Published by Elsevier B.V.

  2. Plant VOC emissions: making use of the unavoidable.

    Science.gov (United States)

    Peñuelas, Josep; Llusià, Joan

    2004-08-01

    All plants emit substantial amounts of phytogenic volatile organic compounds (PVOCs), which include alkanes, alkenes, alcohols, aldehydes, eters, esters and carboxylic acids. Defence, communication and/or protection against extreme conditions have been proposed as reasons for these emissions. However, Rosenstiel and colleagues have recently proposed that emission of PVOCs represents a metabolic 'safety valve' by preventing the unnecessary sequestration of phosphates. Additionally, Niinemets and colleagues suggest that the emission rates of some PVOCs are determined by the principal physicochemical characteristics of the emitted compounds, such as their solubility, volatility and diffusivity, rather than by physiological mechanisms, such as their synthesis rates. These two new studies lead to the hypothesis that there is not necessarily a specific role for every PVOC emitted, given that their emission is unavoidable as result of their volatility. However, in some cases, natural selection has worked to take advantage of this volatility.

  3. Emission inventory of anthropogenic air pollutants and VOC species in the Yangtze River Delta region, China

    Directory of Open Access Journals (Sweden)

    C. Huang

    2011-05-01

    Full Text Available The purpose of this study is to develop an emission inventory for major anthropogenic air pollutants and VOC species in the Yangtze River Delta (YRD region for the year 2007. A "bottom-up" methodology was adopted to compile the inventory based on major emission sources in the sixteen cities of this region. Results show that the emissions of SO2, NOx, CO, PM10, PM2.5, VOCs, and NH3 in the YRD region for the year 2007 are 2392 kt, 2293 kt, 6697 kt, 3116 kt, 1511 kt, 2767 kt, and 459 kt, respectively. Ethylene, mp-xylene, o-xylene, toluene, 1,2,4-trimethylbenzene, 2,4-dimethylpentane, ethyl benzene, propylene, 1-pentene, and isoprene are the key species contributing 77 % to the total ozone formation potential (OFP. The spatial distribution of the emissions shows the emissions and OFPs are mainly concentrated in the urban and industrial areas along the Yangtze River and around Hangzhou Bay. The industrial sources, including power plants other fuel combustion facilities, and non-combustion processes contribute about 97 %, 86 %, 89 %, 91 %, and 69 % of the total SO2, NOx, PM10, PM2.5, and VOC emissions. Vehicles take up 12.3 % and 12.4 % of the NOx and VOC emissions, respectively. Regarding OFPs, the chemical industry, domestic use of paint & printing, and gasoline vehicles contribute 38 %, 24 %, and 12 % to the ozone formation in the YRD region.

  4. A High Performance Biofilter for VOC Emission Control.

    Science.gov (United States)

    Wu, G; Conti, B; Leroux, A; Brzezinski, R; Viel, G; Heitz, M

    1999-02-01

    Biofiltration is a cleaning technique for waste air contaminated with some organic compounds. The advantages of the conventional biofilter over other biological systems are a high-superficial area best suited for the treatment of some compounds with poor water solubility, ease of operation, and low operating costs. It has crucial disadvantages, however; for example, it is not suitable to treat waste gases with high VOC concentrations and it has poor control of reaction conditions. To improve on these problems and to build a high-performance biofilter, three structured peat media and two trickling systems have been introduced in this study. The influences of media size and composition have been investigated experimentally. Peat bead blended with 30% (w/w) certain mineral material with a good binding capacity has advantages over other packing materials, for example, suitable size to prevent blockage due to microbial growth, strong buffering capacity to neutralize acidic substances in the system, and a pH range of 7.0-7.2 suitable for the growth of bacteria. Dropwise trickling system offers an effective measure to easily control the moisture content of the bed and the reaction conditions (pH, nutrient) and to partially remove excess biomass produced during the metabolic processes of microorganisms. The influence of nutrient supplementation has also been investigated in this study, which has revealed that the biological system was in a condition of nutrient limitation instead of carbon limitation. The biofilters built in our laboratory were used to treat waste gas contaminated with toluene in a concentration range of 1 to 3.2 g/m(3) and at the specific gas flow rate of 24 to120 m(3)/m(2).hr. Under the conditions employed, a high elimination capacity (135 g/m(3).hr) was obtained in the biofilter packed with peat beads (blended with 30% of the mineral material), and no blockage problem was observed in an experimental period of 2-3 months.

  5. Performance of the JULES land surface model for UK Biogenic VOC emissions

    Science.gov (United States)

    Hayman, Garry; Comyn-Platt, Edward; Vieno, Massimo; Langford, Ben

    2017-04-01

    Emissions of biogenic non-methane volatile organic compounds (NMVOCs) are important for air quality and tropospheric composition. Through their contribution to the production of tropospheric ozone and secondary organic aerosol (SOA), biogenic VOCs indirectly contribute to climate forcing and climate feedbacks [1]. Biogenic VOCs encompass a wide range of compounds and are produced by plants for growth, development, reproduction, defence and communication [2]. There are both biological and physico-chemical controls on emissions [3]. Only a few of the many biogenic VOCs are of wider interest and only two or three (isoprene and the monoterpenes, α- and β-pinene) are represented in chemical transport models. We use the Joint UK Land Environment Simulator (JULES), the UK community land surface model, to estimate biogenic VOC emission fluxes. JULES is a process-based model that describes the water, energy and carbon balances and includes temperature, moisture and carbon stores [4, 5]. JULES currently provides emission fluxes of the 4 largest groups of biogenic VOCs: isoprene, terpenes, methanol and acetone. The JULES isoprene scheme uses gross primary productivity (GPP), leaf internal carbon and the leaf temperature as a proxy for the electron requirement for isoprene synthesis [6]. In this study, we compare JULES biogenic VOC emission estimates of isoprene and terepenes with (a) flux measurements made at selected sites in the UK and Europe and (b) gridded estimates for the UK from the EMEP/EMEP4UK atmospheric chemical transport model [7, 8], using site-specific or EMEP4UK driving meteorological data, respectively. We compare the UK-scale emission estimates with literature estimates. We generally find good agreement in the comparisons but the estimates are sensitive to the choice of the base or reference emission potentials. References (1) Unger, 2014: Geophys. Res. Lett., 41, 8563, doi:10.1002/2014GL061616; (2) Laothawornkitkul et al., 2009: New Phytol., 183, 27, doi

  6. Volatile Organic Compound (VOC) Emissions from Dairy Cows and Their Waste

    Science.gov (United States)

    Shaw, S.; Holzinger, R.; Mitloehner, F.; Goldstein, A.

    2005-12-01

    Biogenic VOCs are typically defined as those directly emitted from plants, but approximately 6% of global net primary production is consumed by cattle that carry out enteric fermentation and then emit VOCs that could also be considered biogenic. Current regulatory estimates suggest that dairy cattle in central California emit VOCs at rates comparable to those from passenger vehicles in the region, and thus contribute significantly to the extreme non-attainment of ozone standards there. We report PTR-MS measurements of ammonia and VOCs, and cavity-enhanced-absorption gas analyzer (Los Gatos Research, Inc.) measurements of CH4, emitted from dairy cattle in various stages of pregnancy/lactation and their waste. Experiments were conducted in chambers at UC Davis that simulate freestall cow housing conditions. CH4 fluxes ranged from 125-374 lb/cow/year. The compounds with the highest fluxes from '3 cows+waste' treatments were: ammonia (1-18), methanol (0-2.3), acetone+propanal (0.2-0.7), dimethylsulfide (0-0.4), and mass 109 (likely ID = p-cresol; 0-0.3) in lb/cow/year. Mass 60 (likely ID = trimethylamine) and acetic acid were also abundant. There were 10s of additional compounds with detectable, but small, emissions. A few compounds that were likely emitted (i.e. ethanol, formaldehyde, and dimethylamine) were not quantified by the PTR-MS. The total flux for all measured organic gases (TOG = CH4 + PTR-MS VOCs(including acetone+propanal)) averaged 246±45 lb/cow/year for '3 cows+waste' treatments, and was dominated by methane (>98%). TOG flux for 'waste only' treatments averaged 1.1±0.1 lb/cow/year, and was instead dominated by VOC (>84%). The PTR-MS VOCs as a percent of TOG (0.6±0.2%) emitted from '3 cows+waste' treatments in chamber conditions was a factor of 10 smaller than that currently estimated by the California Air Resources Board. In addition, the ozone forming potentials of the most abundant VOCs are only about 10% those of typical combustion or plant

  7. Temperature and light dependence of the VOC emissions of Scots pine

    Directory of Open Access Journals (Sweden)

    V. Tarvainen

    2004-10-01

    Full Text Available The volatile organic compound (VOC emission rates of Scots pine (Pinus sylvestris L. were measured from trees growing in a natural forest environment at two locations in Finland. The emission rate measurements were carried out using a dynamic flow through technique with samples collected on adsorbent tubes and analyzed using thermodesorption followed by a gas chromatograph with a mass-selective detector (GC-MS. The standard emission potentials (at 303.15 K and 1000 µmol photons m−2 s−1 were calculated for the measured compounds using nonlinear regression to fit the experimental data to temperature and light dependent emission algorithms.

    The observed total VOC emission rates varied between 21 and 874 ng/g(dw*h and 268 and 1670 ng/g(dw*h in southern and northern Finland, respectively. A clear seasonal cycle was detected with high emission rates in early spring, a decrease of the emissions in late spring and early summer, high emissions again in late summer, and a gradual decrease in autumn.

    The main emitted compounds were Δ3-carene (southern Finland and α- and β-pinene (northern Finland, with approximate relative contributions of 60–70% and 60–85% of the total observed monoterpene emission rates, respectively. Sesquiterpene (β-caryophyllene and 2-methyl-3-buten-2-ol (MBO emissions were initiated in early summer at both sites. The observed MBO emission rates were between 1 and 3.5% of the total monoterpene emission rates. The sesquiterpene emission rates varied between 2 and 5% of the total monoterpene emission rates in southern Finland, but were high (40% in northern Finland in spring.

    Most of the measured emission rates were found to be well described by the temperature dependent emission algorithm. The calculated standard emission potentials were high in spring and early summer, decreased somewhat in late summer, and were high again towards autumn. The experimental

  8. Temperature and light dependence of the VOC emissions of Scots pine

    Directory of Open Access Journals (Sweden)

    V. Tarvainen

    2005-01-01

    Full Text Available The volatile organic compound (VOC emission rates of Scots pine (Pinus sylvestris L. were measured from trees growing in a natural forest environment at two locations in Finland. The observed total VOC emission rates varied between 21 and 874 ngg-1 h-1 and 268 and 1670 ngg-1 h-1 in southern and northern Finland, respectively. A clear seasonal cycle was detected with high emission rates in early spring, a decrease of the emissions in late spring and early summer, high emissions again in late summer, and a gradual decrease in autumn. The main emitted compounds were Δ3-carene (southern Finland and α- and β-pinene (northern Finland, with approximate relative contributions of 60–70% and 60–85% of the total observed monoterpene emission rates, respectively. Sesquiterpene (β-caryophyllene and 2-methyl-3-buten-2-ol (MBO emissions were initiated in early summer at both sites. The observed MBO emission rates were between 1 and 3.5% of the total monoterpene emission rates. The sesquiterpene emission rates varied between 2 and 5% of the total monoterpene emission rates in southern Finland, but were high (40% in northern Finland in spring. Most of the measured emission rates were found to be well described by the temperature dependent emission algorithm. The calculated standard emission potentials were high in spring and early summer, decreased somewhat in late summer, and were high again towards autumn. The experimental coefficient β ranged from 0.025 to 0.19 (average 0.10 in southern Finland, with strongest temperature dependence in spring and weakest in late summer. Only the emission rates of 1,8-cineole were found to be both light and temperature dependent.

  9. Effect of VOC emissions from vegetation on urban air quality during hot periods

    Science.gov (United States)

    Churkina, Galina; Kuik, Friderike; Bonn, Boris; Lauer, Axel; Grote, Ruediger; Butler, Tim

    2016-04-01

    Programs to plant millions of trees in cities around the world aim at the reduction of summer temperatures, increase of carbon storage, storm water control, and recreational space, as well as at poverty alleviation. These urban greening programs, however, do not take into account how closely human and natural systems are coupled in urban areas. Compared with the surroundings of cities, elevated temperatures together with high anthropogenic emissions of air and water pollutants are quite typical in urban systems. Urban and sub-urban vegetation respond to changes in meteorology and air quality and can react to pollutants. Neglecting this coupling may lead to unforeseen negative effects on air quality resulting from urban greening programs. The potential of emissions of volatile organic compounds (VOC) from vegetation combined with anthropogenic emissions of air pollutants to produce ozone has long been recognized. This ozone formation potential increases under rising temperatures. Here we investigate how emissions of VOC from urban vegetation affect corresponding ground-level ozone and PM10 concentrations in summer and especially during heat wave periods. We use the Weather Research and Forecasting Model with coupled atmospheric chemistry (WRF-CHEM) to quantify these feedbacks in the Berlin-Brandenburg region, Germany during the two summers of 2006 (heat wave) and 2014 (reference period). VOC emissions from vegetation are calculated by MEGAN 2.0 coupled online with WRF-CHEM. Our preliminary results indicate that the contribution of VOCs from vegetation to ozone formation may increase by more than twofold during heat wave periods. We highlight the importance of the vegetation for urban areas in the context of a changing climate and discuss potential tradeoffs of urban greening programs.

  10. Evaluating the effectiveness of joint emission control policies on the reduction of ambient VOCs: Implications from observation during the 2014 APEC summit in suburban Beijing

    Science.gov (United States)

    Li, Kun; Li, Junling; Wang, Weigang; Tong, Shengrui; Liggio, John; Ge, Maofa

    2017-09-01

    Ambient volatile organic compounds (VOCs) at a suburban Beijing site were on-line detected using proton transfer reaction-mass spectrometry (PTR-MS) during autumn of 2014, near the location of the Asia-Pacific Economic Cooperation (APEC) summit. During the APEC summit, the Chinese government enacted strict emission control policies. It was found that VOC concentrations only slightly decreased during the first emission control period (EC I), when control policies were performed in Beijing and 5 cities along the Tai-hang Mountains. However, most of the VOCs (10 out of 12 non-biogenic species) significantly decreased (more than 40%) during the second emission control period (EC II), when control policies were carried out in 16 cities including Beijing, Tianjin, 8 cities of Hebei province and 6 cities of Shandong province. Also the ratio of toluene and benzene decreased during EC II, likely because the emission control policies changed the proportions of different anthropogenic sources. Using the positive matrix factorization (PMF) source apportionment method, five factors are analyzed: (1) vehicle + fuel, (2) solvent, (3) biomass burning, (4) secondary, and (5) background + long-lived. Among them, vehicle + fuel, solvent and biomass burning contribute most of the VOCs concentrations (60%-80%) during the polluted periods and are affected most by emission control policies. During EC II, the reductions of vehicle + fuel, solvent, biomass burning and secondary species were all no less than 50%. Overall, when emission control policies were carried out in many North China Plain (NCP) cities (i.e. EC II), the VOC concentrations of suburban Beijing markedly decreased. This indicates the cross-regional joint-control policies have a large influence on reductions of organic gas species. The findings of this study have vital implications for helping formulate effective emission control policies in China and other countries.

  11. Diffusion-controlled toluene reference material for VOC emissions testing: international interlaboratory study.

    Science.gov (United States)

    Howard-Reed, Cynthia; Liu, Zhe; Cox, Steven; Leber, Dennis; Samarov, Dan; Little, John C

    2014-04-01

    The measurement of volatile organic compound (VOC) emissions from building products and materials by manufacturers and testing laboratories, and the use of the test results for labeling programs, continue to expand. One issue that hinders wide acceptance for chamber product testing is the lack of a reference material to validate test chamber performance. To meet this need, the National Institute of Standards and Technology (NIST) and Virginia Tech (VT) have developed a prototype reference material that emits a single VOC similar to the emissions of a diffusion-controlled building product source with a dynamic emissions profile. The prototype material has undergone extensive testing at NIST and a pilot interlaboratory study (ILS) with four laboratories. The next development step is an evaluation of the prototype source in multiple-sized chambers of 14 laboratories in seven countries. Each laboratory was provided duplicate specimens and a test protocol. Study results identified significant issues related to the need to store the source at a subzero Celsius temperature until tested and possible inconsistencies in large chambers. For laboratories using a small chamber and meeting all the test method criteria, the results were very encouraging with relative standard deviations ranging from 5% to 10% across the laboratories. Currently, the chamber performance of laboratories conducting product VOC emissions testing is assessed through interlaboratory studies (ILS) using a source with an unknown emission rate. As a result, laboratory proficiency can only be based on the mean and standard deviation of emission rates measured by the participating ILS laboratories. A reference material with a known emission rate has the potential to provide an independent assessment of laboratory performance as well as improve the quality of interlaboratory studies. Several international laboratories with different chamber testing systems demonstrated the ability to measure the emission rate

  12. Determination of radon exhalation from construction materials using VOC emission test chambers.

    Science.gov (United States)

    Richter, M; Jann, O; Kemski, J; Schneider, U; Krocker, C; Hoffmann, B

    2013-10-01

    The inhalation of (222) Rn (radon) decay products is one of the most important reasons for lung cancer after smoking. Stony building materials are an important source of indoor radon. This article describes the determination of the exhalation rate of stony construction materials by the use of commercially available measuring devices in combination with VOC emission test chambers. Five materials - two types of clay brick, clinker brick, light-weight concrete brick, and honeycomb brick - generally used for wall constructions were used for the experiments. Their contribution to real room concentrations was estimated by applying room model parameters given in ISO 16000-9, RP 112, and AgBB. This knowledge can be relevant, if for instance indoor radon concentration is limited by law. The test set-up used here is well suited for application in test laboratories dealing with VOC emission testing.

  13. Non-Destructive Evaluation of Historical Paper Based on pH Estimation from VOC Emissions

    Directory of Open Access Journals (Sweden)

    Boris Pihlar

    2007-12-01

    Full Text Available Volatile organic compounds (VOCs emitted from materials during degradationcan be a valuable source of information. In this work, the emissions of furfural and aceticacid from cellulose were studied using solid-phase micro-extraction (SPME incombination with gas chromatography-mass spectrometry. Two sampling techniques wereemployed: static headspace sampling using SPME for 1 h at 40 oC after 18-h samplepreparation at 80 oC in a closed glass vial, and contact SPME in a stack of paper (or abook. While a number of VOCs are emitted from paper under conditions of natural oraccelerated degradation, two compounds were confirmed to be of particular diagnosticvalue: acetic acid and furfural. The emissions of furfural are shown to correlate with pH ofthe cellulosic environment. Since pH is one of the most important parameters regardingdurability of this material, the developed method could be used for non-destructiveevaluation of historical paper.

  14. Emissions of volatile organic compounds (VOCs) from concentrated animal feeding operations (CAFOs): chemical compositions and separation of sources

    Science.gov (United States)

    Yuan, Bin; Coggon, Matthew M.; Koss, Abigail R.; Warneke, Carsten; Eilerman, Scott; Peischl, Jeff; Aikin, Kenneth C.; Ryerson, Thomas B.; de Gouw, Joost A.

    2017-04-01

    Concentrated animal feeding operations (CAFOs) emit a large number of volatile organic compounds (VOCs) to the atmosphere. In this study, we conducted mobile laboratory measurements of VOCs, methane (CH4) and ammonia (NH3) downwind of dairy cattle, beef cattle, sheep and chicken CAFO facilities in northeastern Colorado using a hydronium ion time-of-flight chemical-ionization mass spectrometer (H3O+ ToF-CIMS), which can detect numerous VOCs. Regional measurements of CAFO emissions in northeastern Colorado were also performed using the NOAA WP-3D aircraft during the Shale Oil and Natural Gas Nexus (SONGNEX) campaign. Alcohols and carboxylic acids dominate VOC concentrations and the reactivity of the VOCs with hydroxyl (OH) radicals. Sulfur-containing and phenolic species provide the largest contributions to the odor activity values and the nitrate radical (NO3) reactivity of VOC emissions, respectively. VOC compositions determined from mobile laboratory and aircraft measurements generally agree well with each other. The high time-resolution mobile measurements allow for the separation of the sources of VOCs from different parts of the operations occurring within the facilities. We show that the emissions of ethanol are primarily associated with feed storage and handling. Based on mobile laboratory measurements, we apply a multivariate regression analysis using NH3 and ethanol as tracers to determine the relative importance of animal-related emissions (animal exhalation and waste) and feed-related emissions (feed storage and handling) for different VOC species. Feed storage and handling contribute significantly to emissions of alcohols, carbonyls, carboxylic acids and sulfur-containing species. Emissions of phenolic species and nitrogen-containing species are predominantly associated with animals and their waste.

  15. Emission characteristics of VOCs from three fixed-roof p-xylene liquid storage tanks.

    Science.gov (United States)

    Lu, Chungsying; Huang, Hsiaoyun; Chang, Shenteng; Hsu, Shihchieh

    2013-08-01

    This study evaluates emission characteristics of volatile organic compounds (VOCs) caused by standing loss (L S) and working loss (L W) of three vertical fixed-roof p-xylene (p-X) liquid tanks during 1-year storage and filling operation. The annual net throughput of the tanks reached 70,446 t, resulting in 9,425 kg of p-X vapor emission including 5,046 kg of L S (53.54 %) and 4,379 kg of L W (46.46 %). The estimated L W of AP-42 displayed better agreement with the measured values of a VOC detector than the estimated L S of AP-42. The L S was best correlated with the liquid height of the tanks, while the L W was best correlated with the net throughput of the tanks. As a result, decreasing vapor space volume of the tanks and avoiding high net throughput of the tanks in a high ambient temperature period were considered as effective means to lessen VOC emission from the fixed-roof organic liquid storage tank.

  16. Measurements of volatile organic compounds at a suburban ground site (T1 in Mexico City during the MILAGRO 2006 campaign: measurement comparison, emission ratios, and source attribution

    Directory of Open Access Journals (Sweden)

    D. M. Bon

    2010-10-01

    Full Text Available Volatile organic compound (VOC mixing ratios were measured with two different instruments at the T1 ground site in Mexico City during the Megacity Initiative: Local and Global Research Observations (MILAGRO campaign in March of 2006. A gas chromatograph with flame ionization detector (GC-FID quantified 18 light alkanes, alkenes and acetylene while a proton-transfer-reaction ion-trap mass spectrometer (PIT-MS quantified 12 VOC species including oxygenated VOCs (OVOCs and aromatics. A GC separation system was used in conjunction with the PIT-MS (GC-PIT-MS to evaluate PIT-MS measurements and to aid in the identification of unknown VOCs. The VOC measurements are also compared to simultaneous canister samples and to two independent proton-transfer-reaction mass spectrometers (PTR-MS deployed on a mobile and an airborne platform during MILAGRO. VOC diurnal cycles demonstrate the large influence of vehicle traffic and liquid propane gas (LPG emissions during the night and photochemical processing during the afternoon. Emission ratios for VOCs and OVOCs are determined from early-morning enhancement ratios and compared to emission ratios calculated from the PMF results. Average emission ratios for non-oxygenated species relative to CO are on average a factor of 2 higher than measured for US cities. Emission ratios for OVOCs are estimated and compared to literature values the northeastern US and to tunnel studies in California. Positive matrix factorization analysis (PMF is used to provide insight into VOC sources and processing and to estimate OVOC emission ratios. Three PMF factors were distinguished by the analysis including the emissions from vehicles, the use of liquid propane gas and the production of secondary VOCs + long-lived species. The total PIT-MS signal was summed to estimate the fraction of identified vs. unidentified VOC species.

  17. The Amazonian Floodplains, an ecotype with challenging questions on volatile organic compound (VOC) emissions

    Science.gov (United States)

    Kesselmeier, J.

    2012-12-01

    Volatile organic compound (VOC) emissions are affected by a variety of biotic and abiotic factors such as light intensity, temperature, CO2 and drought. Another factor usually overlooked but very important for the tropical rainforest in Amazonia is regular flooding. According to recent estimates, the total Amazonian floodplain area easily ranges up to 700,000 km^2, including whitewater river floodplains (várzea) blackwater regions (igapó) and further clearwater regions. Regarding the total Amazonian wetlands the area sums up to more than 2.000.000 km^2, i.e. 30% of Amazonia. To survive the flooding periods causing anoxic conditions for the root system of up to several months, vegetation has developed several morphological, anatomical and physiological strategies. One is to switch over the root metabolism to fermentation, thus producing ethanol as one of the main products. Ethanol is a toxic metabolite which is transported into the leaves by the transpiration stream. From there it can either be directly emitted into the atmosphere, or can be re-metabolized to acetaldehyde and/or acetate. All of these compounds are volatile enough to be partly released into the atmosphere. We observed emissions of ethanol, acetaldehyde and acetic acid under root anoxia. Furthermore, plant stress induced by flooding also affected leaf primary physiological processes as well as other VOC emissions such as the release of isoprenoids and other volatiles. For example, Hevea spruceana could be identified as a monoterpene emitting tree species behaving differently upon anoxia depending on the origin, with increasing emissions of the species from igapó and decreasing with the corresponding species from várzea. Contrasting such short term inundations, studies of VOC emissions under long term conditions (2-3 months) did not confirm the ethanol/acetaldehyde emissions, whereas emissions of other VOC species decreased considerably. These results demonstrate that the transfer of our knowledge

  18. Measurements of volatile organic compounds at a suburban ground site (T1 in Mexico City during the MILAGRO 2006 campaign: measurement comparison, emission ratios, and source attribution

    Directory of Open Access Journals (Sweden)

    D. M. Bon

    2011-03-01

    Full Text Available Volatile organic compound (VOC mixing ratios were measured with two different instruments at the T1 ground site in Mexico City during the Megacity Initiative: Local and Global Research Observations (MILAGRO campaign in March of 2006. A gas chromatograph with flame ionization detector (GC-FID quantified 18 light alkanes, alkenes and acetylene while a proton-transfer-reaction ion-trap mass spectrometer (PIT-MS quantified 12 VOC species including oxygenated VOCs (OVOCs and aromatics. A GC separation system was used in conjunction with the PIT-MS (GC-PIT-MS to evaluate PIT-MS measurements and to aid in the identification of unknown VOCs. The VOC measurements are also compared to simultaneous canister samples and to two independent proton-transfer-reaction mass spectrometers (PTR-MS deployed on a mobile and an airborne platform during MILAGRO. VOC diurnal cycles demonstrate the large influence of vehicle traffic and liquid propane gas (LPG emissions during the night and photochemical processing during the afternoon. Emission ratios for VOCs and OVOCs relative to CO are derived from early-morning measurements. Average emission ratios for non-oxygenated species relative to CO are on average a factor of ~2 higher than measured for US cities. Emission ratios for OVOCs are estimated and compared to literature values the northeastern US and to tunnel studies in California. Positive matrix factorization analysis (PMF is used to provide insight into VOC sources and processing. Three PMF factors were distinguished by the analysis including the emissions from vehicles, the use of liquid propane gas and the production of secondary VOCs + long-lived species. Emission ratios to CO calculated from the results of PMF analysis are compared to emission ratios calculated directly from measurements. The total PIT-MS signal is summed to estimate the fraction of identified versus unidentified VOC species.

  19. Measurements and modeling to quantify emissions of methane and VOCs from shale gas operations: Final Report

    Energy Technology Data Exchange (ETDEWEB)

    Presto, Albert A [Carnegie Mellon Univ., Pittsburgh, PA (United States)

    2017-06-30

    The objectives of the project were to determine the leakage rates of methane and ozone-forming Volatile Organic Compounds (VOCs) and the emission rates of air toxics from Marcellus shale gas activities. Methane emissions in the Marcellus Shale region were differentiated between “newer” sources associated with shale gas development and “older” sources associated with coal or conventional natural gas exploration. This project conducted measurements of methane and VOC emissions from both shale and non-shale natural gas resources. The initial scope of the project was the Marcellus Shale basin, and measurements were conducted in both the western wet gas regions (southwest PA and WV) and eastern dry gas region (northeast PA) of the basin. During this project, we obtained additional funding from other agencies to expand the scope of measurements to include additional basins. The data from both the Marcellus and other basins were combined to construct a national analysis of methane emissions from oil & gas production activities.

  20. Global Emissions of Terpenoid VOCs from Terrestrial Vegetation in the Last Millennium

    Energy Technology Data Exchange (ETDEWEB)

    Acosta Navarro, J. C.; Smolander, S.; Struthers, H.; Zorita, E.; Ekman, A. M.; Kaplan, J. O.; Guenther, Alex B.; Arneth, A.; Riipinen, I.

    2014-06-16

    land cover change. In addition, isoprene emission sensitivity to drought proved to have signifcant short term global effects. By the end of the past millennium MEGAN isoprene emissions were 634 TgC yr-1 (13% and 19% less than during during 1750-1850 and 1000- 1200, respectively) and LPJ-GUESS emissions were 323 TgC yr-1 (15% and 16 17 20% less than during 1750-1850 and 1000-1200, respectively). Monoterpene emissions were 89 TgC yr-1 (10% and 6% higher than during 1750-1850 and 18 1000-1200, respectively) in MEGAN, and 24 TgC yr-1 (2% higher and 5% less than during 1750-1850 and 1000-1200, respectively) in LPJ-GUESS. MEGAN sesquiterpene emissions were 36 TgC yr-1 (10% and 4% higher than during1750-1850 and 1000-1200, respectively). Although both models capture similar emission trends, the magnitude of the emissions are different. This highlights the importance of building better constraints on VOC emissions from terrestrial vegetation.emission trends, the magnitude of the emissions are different. This highlights the importance of building better constraints on VOC emissions from terrestrial vegetation.

  1. Pulsed Corona Plasma Technology for Treating VOC Emissions from Pulp Mills

    Energy Technology Data Exchange (ETDEWEB)

    Fridman, Alexander A.; Gutsol, Alexander; Kennedy, Lawrence A.; Saveliev, Alexei V.; Korobtsev, Sergey V.; Shiryaevsky, Valery L.; Medvedev, Dmitry

    2004-07-28

    Under the DOE Office of Industrial Technologies Forest Products program various plasma technologies were evaluated under project FWP 49885 ''Experimental Assessment of Low-Temperature Plasma Technologies for Treating Volatile Organic Compound Emissions from Pulp Mills and Wood Products Plants''. The heterogeneous pulsed corona discharge was chosen as the best non-equilibrium plasma technology for control of the vent emissions from HVLC Brownstock Washers. The technology for removal of Volatile Organic Compounds (VOCs) from gas emissions with conditions typical of the exhausts of the paper industry by means of pulsed corona plasma techniques presented in this work. For the compounds of interest in this study (methanol, acetone, dimethyl sulfide and ? -pinene), high removal efficiencies were obtained with power levels competitive with the present technologies for the VOCs removal. Laboratory experiments were made using installation with the average power up to 20 W. Pilot plant prepared for on-site test has average plasma power up to 6.4 kW. The model of the Pilot Plant operation is presented.

  2. Large decrease of VOC emissions of Switzerland's car fleet during the past decade: results from a highway tunnel study

    Science.gov (United States)

    Stemmler, Konrad; Bugmann, Stefan; Buchmann, Brigitte; Reimann, Stefan; Staehelin, Johannes

    The emissions of 14 C 4-C 8 VOC species from road traffic have been measured in a highway tunnel (Gubristtunnel) near Zurich, Switzerland in 2002. The investigated traffic situation corresponds to highway driving with an average speed of 90 km h -1 and hot engine conditions. The comparison with measurements in the same tunnel performed in 1993 indicates that the emission factors of the individual hydrocarbons decreased on average by 80% in the 9 years between both investigations. This improvement can mainly be explained by the nearly complete elimination of non-catalyst gasoline-fuelled cars from the Swiss car fleet in the past decade. The relative emission strengths of the quantified individual VOCs were similar in 1993 and 2002. The emission factors reported in this study are the lowest reported from on-road vehicle emission measurements so far, indicating the efficient technology of modern car fleets with respect to VOC emissions. The emission factors derived from the tunnel study are compared to modelled emission factors based on dynamometric test measurements on Swiss passenger cars. The employed model is the Handbuch für Emissionsfaktoren des Strassenverkehrs; version 1.2 (Umweltbundesamt Berlin and INFRAS AG Bern, 1999). A good agreement between the modelled and measured emissions was found for the investigated traffic situation, indicating that the development of the VOC emissions during the last decade is well understood on the basis of the fleet composition and the dynamometric test measurements. The observed VOC emission reduction corresponds to a traffic situation, where an optimal exhaust gas catalyst performance can be expected. Factors leading to a somewhat less beneficial influence of the catalytic converter technique in other relevant driving situations are therefore additionally discussed.

  3. On-line field measurements of VOC emissions from a spruce tree at SMEAR Estonia

    Science.gov (United States)

    Bourtsoukidis, Efstratios; Bonn, Boris; Noe, Steffen

    2013-04-01

    We have investigated VOC emissions from a Norway spruce tree (Picea abies) in a hemi-boreal mixed forest in September and October 2012, using Proton Transfer Reaction Mass Spectrometry and Gas Chromatography - Mass Spectrometry techniques, applied in a dynamic branch enclosure system that was automatically operated with an electrical compressor. Parallel to BVOC measurements a vast amount of atmospheric (CO2, CH4, H2O, CO, particles) and meteorological (temperature, relative humidity, photosynthetic active radiation, wind speed and direction, precipitation) parameters were measured in the ambient atmosphere and inside the cuvette enclosure (temperature, relative humidity, O3). Prior to the measuring period, an innovatory experimental setup was built at Järvselja forest station, in order to accomplish the detection of BVOC and minimize sampling losses. Therefore, a new inlet line, consisting of 19.4m of heated and isolated glass tube was constructed. The new inlet system applied, allowed the on-line detection and calculation of sesquiterpene (SQT) emission rates for the first time in a hemi-boreal forest site. It total, 12 atmospheric relevant BVOCs were continuously monitored for a three week period and the emission rates were derived. Along with diurnal profiles and continuous timeless, some interesting observations showed the possibility of ozone effect on SQT emissions, the possibility of radiation effect on MT emissions, the higher induced emissions due to mechanical stress and the possibility for a valid intercomparison between different spruce trees located in mountain Kleiner Feldberg (Germany) and in Järvseja forest station (Estonia).

  4. Measurement of VOC and SVOC emissions from computer monitors with a 1 m{sup 3} emission test chamber

    Energy Technology Data Exchange (ETDEWEB)

    Wensing, M. [Fraunhofer Wilhelm-Klauditz-Inst., Material Analysis and Indoor Chemistry (Germany)

    2004-07-01

    Electronic devices such as computer monitors emit a large number of different chemicals to the indoor air and their environment under operating conditions, particularly due to their heat development. This basically creates a potential exposure of the room users to those chemicals, some of which may be injurious to human health because of their classification as toxic substances. The spectrum of emissions ranges from more volatile (VOC) auxiliary production agents (solvents) and residual emissions of plastic monomers up to more semi-volatile plasticizers and flame retardants (SVOC) which are added to polymer materials in a well-aimed way in order to achieve certain desired material properties durably. The paper describes the measurement of these emissions with a 1 m{sup 3} test chamber and the health-related evaluation of the results. (orig.)

  5. Seasonal and species-specific response of VOC emissions by Mediterranean woody plant to elevated ozone concentrations

    Science.gov (United States)

    Llusià, J.; Peñuelas, J.; Gimeno, B. S.

    Although certain factors controlling plant emission rates of volatile organic compounds (VOCs) are reasonably well understood, the influence of elevated ozone concentrations as abiotic stress is mostly unknown. Therefore, we studied the effects of ozone concentrations on seasonal biogenic volatile organic compound (BVOC) emissions by different Mediterranean plant species in open top chambers (OTC). Three ozone treatments were established: filtered air (F), non-filtered air (NF), and fumigated air (NF+) adding 40 nl l -1 of ozone over NF. We studied the response of VOC emission in saplings of four Mediterranean woody plant species and subspecies: Ceratonia siliqua L., Olea europaea L., Quercus ilex spp. ilex L., and Quercus ilex spp. rotundifolia L. as representative of natural Mediterranean vegetation. No visible symptoms were detected on the leaves. No significant effect was found on net photosynthetic rates or stomatal conductance except for an increase in net photosynthetic rates in Quercus ilex ilex in spring and summer and an overall slight increase in Quercus ilex rotundifolia. Emissions of the total VOCs from Ceratonia siliqua in summer, and from Olea europaea and Quercus ilex rotundifolia in spring increased in ozone fumigated OTC in comparison with F or NF OTC. Decreased emissions were found in Quercus ilex rotundifolia in summer. There were no significant differences between ozone fumigation treatments for the other plant species and seasons. When considering particular VOCs, the results were also variable among species and time of the year. While α-pinene emissions decreased with ozone fumigation in Olea europaea, α-pinene and limonene emissions increased in Quercus ilex ilex. The responses of these particular VOCs did not always match the responses of total VOCs. In spite of this strong variability, when considering overall annual data for all species and seasons, there were increased net photosynthetic rates (37%) and limonene (95%) and total VOC (45

  6. Seasonal and species-specific response of VOC emissions by Mediterranean woody plant to elevated ozone concentrations

    Energy Technology Data Exchange (ETDEWEB)

    Llusia, J.; Penuelas, J. [Universitat Autonoma de Barcelona (Spain). Unitat Ecofisiologia CSIC-CEAB-CREAF; Gimeno, R.S. [CIEMAT, Madrid (Spain). Ecotoxicologia de la Contaminacion Atmosferica

    2002-08-01

    Although certain factors controlling plant emission rates of volatile organic compounds (VOCs) are reasonably well understood, the influence of elevated ozone concentrations as abiotic stress is mostly unknown. Therefore, we studied the effects of ozone concentrations on seasonal biogenic volatile organic compound (BVOC) emissions by different Mediterranean plant species in open top chambers (OTC). Three ozone treatments were established: filtered air (F), non-filtered air (NF), and fumigated air (NF+) adding 40 nl l{sup -1} of ozone over NF. We studied the response of VOC emission in saplings of four Mediterranean woody plant species and subspecies: Ceratonia siliqua L., Olea europaea L., Quercus ilex spp. ilex L., and Quercus ilex spp. rotundifolia L. as representative of natural Mediterranean vegetation. No visible symptoms were detected on the leaves. No significant effect was found on net photosynthetic rates or stomatal conductance except for an increase in net photosynthetic rates in Quercus ilex ilex in spring and summer and an overall slight increase in Quercus ilex rotundifolia. Emissions of the total VOCs from Ceratonia siliqua in summer, and from Olea europaea and Quercus ilex rotundifolia in spring increased in ozone fumigated OTC in comparison with F or NF OTC. Decreased emissions were found in Quercus ilex rotundifolia in summer. There were no significant differences between ozone fumigation treatments for the other plant species and seasons. When considering particular VOCs, the results were also variable among species and time of the year. While {alpha}-pinene emissions decreased with ozone fumigation in Olea europaea, {alpha}-pinene and limonene emissions increased in Quercus ilex ilex. The responses of these particular VOCs did not always match the responses of total VOCs. In spite of this strong variability, when considering overall annual data for all species and seasons, there were increased net photosynthetic rates (37%) and limonene (95

  7. A refined 2010-based VOC emission inventory and its improvement on modeling regional ozone in the Pearl River Delta Region, China.

    Science.gov (United States)

    Yin, Shasha; Zheng, Junyu; Lu, Qing; Yuan, Zibing; Huang, Zhijiong; Zhong, Liuju; Lin, Hui

    2015-05-01

    Accurate and gridded VOC emission inventories are important for improving regional air quality model performance. In this study, a four-level VOC emission source categorization system was proposed. A 2010-based gridded Pearl River Delta (PRD) regional VOC emission inventory was developed with more comprehensive source coverage, latest emission factors, and updated activity data. The total anthropogenic VOC emission was estimated to be about 117.4 × 10(4)t, in which on-road mobile source shared the largest contribution, followed by industrial solvent use and industrial processes sources. Among the industrial solvent use source, furniture manufacturing and shoemaking were major VOC emission contributors. The spatial surrogates of VOC emission were updated for major VOC sources such as industrial sectors and gas stations. Subsector-based temporal characteristics were investigated and their temporal variations were characterized. The impacts of updated VOC emission estimates and spatial surrogates were evaluated by modeling O₃ concentration in the PRD region in the July and October of 2010, respectively. The results indicated that both updated emission estimates and spatial allocations can effectively reduce model bias on O₃ simulation. Further efforts should be made on the refinement of source classification, comprehensive collection of activity data, and spatial-temporal surrogates in order to reduce uncertainty in emission inventory and improve model performance.

  8. [Volatile organic compounds (VOCs) emitted from wood furniture--estimation of emission rate by passive flux sampler].

    Science.gov (United States)

    Jinno, Hideto; Tanaka-Kagawa, Toshiko; Furuta, Mitsuko; Shibatsuji, Masayoshi; Nishimura, Tetsuji

    2011-01-01

    The aim of this study was to evaluate aldehydes and other volatile organic compounds (VOCs) emission from furniture, which may cause hazardous influence on human being such as sick building/sick house syndrome. In this study, VOCs emitted from six kinds of wood furniture, including three set of dining tables and three beds, were analyzed by large chamber test method (JIS A 1911). Based on the emission rates of total VOCs (TVOC), the impacts on the indoor TVOC was estimated by the simulation model with volume of 20 m3 and ventilation frequency of 0.5 times/h. The estimated increment of formaldehyde were exceeded the guideline value (100 microg/m3) in one set of dining table and one bed. The estimated TVOC increment values were exceeded the provisional target value for indoor air (400 microg/m3) in two sets of dining tables and two beds. These results revealed that VOC emissions from wood furniture may influence significantly indoor air quality. Also, in this study, to establish the alternative method for large chamber test methods, emission rates from representative five areas of furniture unit were evaluated by passive sampling method using flux sampler and emission rate from full-sized furniture was predicted. Emission rates predicted by flux passive sampler were 10-106% (formaldehyde) and 8-141% (TVOC) of the data measured using large chamber test, respectively.

  9. Human health risk evaluation of selected VOC, SVOC and particulate emissions from scented candles.

    Science.gov (United States)

    Petry, Thomas; Vitale, Danielle; Joachim, Fred J; Smith, Ben; Cruse, Lynn; Mascarenhas, Reuben; Schneider, Scott; Singal, Madhuri

    2014-06-01

    Airborne compounds in the indoor environment arise from a wide variety of sources such as environmental tobacco smoke, heating and cooking, construction materials as well as outdoor sources. To understand the contribution of scented candles to the indoor load of airborne substances and particulate matter, candle emission testing was undertaken in environmentally controlled small and large emission chambers. Candle emission rates, calculated on the basis of measured chamber concentrations of volatile and semi-volatile organic compounds (VOC, SVOC) and particulate matter (PM), were used to predict their respective indoor air concentrations in a standard EU-based dwelling using 2 models: the widely accepted ConsExpo 1-box inhalation model and the recently developed RIFM 2-box indoor air dispersion model. The output from both models has been used to estimate more realistic consumer exposure concentrations of specific chemicals and PM in candle emissions. Potential consumer health risks associated with the candle emissions were characterized by comparing the exposure concentrations with existing indoor or ambient air quality guidelines or, where not existent, to established toxicity thresholds. On the basis of this investigation it was concluded that under normal conditions of use scented candles do not pose known health risks to the consumer.

  10. Influence of precision of emission characteristic parameters on model prediction error of VOCs/formaldehyde from dry building material.

    Directory of Open Access Journals (Sweden)

    Wenjuan Wei

    Full Text Available Mass transfer models are useful in predicting the emissions of volatile organic compounds (VOCs and formaldehyde from building materials in indoor environments. They are also useful for human exposure evaluation and in sustainable building design. The measurement errors in the emission characteristic parameters in these mass transfer models, i.e., the initial emittable concentration (C 0, the diffusion coefficient (D, and the partition coefficient (K, can result in errors in predicting indoor VOC and formaldehyde concentrations. These errors have not yet been quantitatively well analyzed in the literature. This paper addresses this by using modelling to assess these errors for some typical building conditions. The error in C 0, as measured in environmental chambers and applied to a reference living room in Beijing, has the largest influence on the model prediction error in indoor VOC and formaldehyde concentration, while the error in K has the least effect. A correlation between the errors in D, K, and C 0 and the error in the indoor VOC and formaldehyde concentration prediction is then derived for engineering applications. In addition, the influence of temperature on the model prediction of emissions is investigated. It shows the impact of temperature fluctuations on the prediction errors in indoor VOC and formaldehyde concentrations to be less than 7% at 23±0.5°C and less than 30% at 23±2°C.

  11. Influence of precision of emission characteristic parameters on model prediction error of VOCs/formaldehyde from dry building material.

    Science.gov (United States)

    Wei, Wenjuan; Xiong, Jianyin; Zhang, Yinping

    2013-01-01

    Mass transfer models are useful in predicting the emissions of volatile organic compounds (VOCs) and formaldehyde from building materials in indoor environments. They are also useful for human exposure evaluation and in sustainable building design. The measurement errors in the emission characteristic parameters in these mass transfer models, i.e., the initial emittable concentration (C 0), the diffusion coefficient (D), and the partition coefficient (K), can result in errors in predicting indoor VOC and formaldehyde concentrations. These errors have not yet been quantitatively well analyzed in the literature. This paper addresses this by using modelling to assess these errors for some typical building conditions. The error in C 0, as measured in environmental chambers and applied to a reference living room in Beijing, has the largest influence on the model prediction error in indoor VOC and formaldehyde concentration, while the error in K has the least effect. A correlation between the errors in D, K, and C 0 and the error in the indoor VOC and formaldehyde concentration prediction is then derived for engineering applications. In addition, the influence of temperature on the model prediction of emissions is investigated. It shows the impact of temperature fluctuations on the prediction errors in indoor VOC and formaldehyde concentrations to be less than 7% at 23±0.5°C and less than 30% at 23±2°C.

  12. Composition of gaseous organic carbon during ECOCEM in Beirut, Lebanon: new observational constraints for VOC anthropogenic emission evaluation in the Middle East

    Science.gov (United States)

    Salameh, Thérèse; Borbon, Agnès; Afif, Charbel; Sauvage, Stéphane; Leonardis, Thierry; Gaimoz, Cécile; Locoge, Nadine

    2017-01-01

    The relative importance of eastern Mediterranean emissions is suspected to be largely underestimated compared to other regions worldwide. Here we use detailed speciated measurements of volatile organic compounds (VOCs) to evaluate the spatial heterogeneity of VOC urban emission composition and the consistency of regional and global emission inventories downscaled to Lebanon (European Monitoring and Evaluation Programme, EMEP; Atmospheric Chemistry and Climate Model Intercomparison Project, ACCMIP; and MACCity, Monitoring Atmospheric Composition and Climate and megaCITY Zoom for the Environment). The assessment was conducted through the comparison of the emission ratios (ERs) extracted from the emission inventories to the ones obtained from the hourly observations collected at a suburban site in Beirut, Lebanon, during summer and winter ECOCEM (Emissions and Chemistry of Organic Carbon in the Eastern Mediterranean) campaigns. The observed ERs were calculated using two independent methods. ER values from both methods agree very well and are comparable to the ones of the road transport sector from near-field measurements for more than 80 % of the species. There is no significant seasonality in ER for more than 90 % of the species, unlike the seasonality usually observed in other cities worldwide. Regardless of the season, ERs agree within a factor of 2 between Beirut and other representative cities worldwide, except for the unburned fuel fraction and ethane. ERs of aromatics (except benzene) are higher in Beirut compared to northern post-industrialized countries and even the Middle Eastern city Mecca. The comparison of the observed ER to the ones extracted from the ACCMIP and MACCity global emission inventories suggests that the overall speciation of anthropogenic sources for major hydrocarbons that act as ozone and secondary organic aerosol (SOA) precursors in ACCMIP is better represented than other species. The comparison of the specific road transport ERs, relative

  13. [Study on the quantitative estimation method for VOCs emission from petrochemical storage tanks based on tanks 4.0.9d model].

    Science.gov (United States)

    Li, Jing; Wang, Min-Yan; Zhang, Jian; He, Wan-Qing; Nie, Lei; Shao, Xia

    2013-12-01

    VOCs emission from petrochemical storage tanks is one of the important emission sources in the petrochemical industry. In order to find out the VOCs emission amount of petrochemical storage tanks, Tanks 4.0.9d model is utilized to calculate the VOCs emission from different kinds of storage tanks. VOCs emissions from a horizontal tank, a vertical fixed roof tank, an internal floating roof tank and an external floating roof tank were calculated as an example. The consideration of the site meteorological information, the sealing information, the tank content information and unit conversion by using Tanks 4.0.9d model in China was also discussed. Tanks 4.0.9d model can be used to estimate VOCs emissions from petrochemical storage tanks in China as a simple and highly accurate method.

  14. Spectral ratio method for measuring emissivity

    Science.gov (United States)

    Watson, K.

    1992-01-01

    The spectral ratio method is based on the concept that although the spectral radiances are very sensitive to small changes in temperature the ratios are not. Only an approximate estimate of temperature is required thus, for example, we can determine the emissivity ratio to an accuracy of 1% with a temperature estimate that is only accurate to 12.5 K. Selecting the maximum value of the channel brightness temperatures is an unbiased estimate. Laboratory and field spectral data are easily converted into spectral ratio plots. The ratio method is limited by system signal:noise and spectral band-width. The images can appear quite noisy because ratios enhance high frequencies and may require spatial filtering. Atmospheric effects tend to rescale the ratios and require using an atmospheric model or a calibration site. ?? 1992.

  15. Do time-averaged, whole-building, effective volatile organic compound (VOC) emissions depend on the air exchange rate? A statistical analysis of trends for 46 VOCs in U.S. offices.

    Science.gov (United States)

    Rackes, A; Waring, M S

    2016-08-01

    We used existing data to develop distributions of time-averaged air exchange rates (AER), whole-building 'effective' emission rates of volatile organic compounds (VOC), and other variables for use in Monte Carlo analyses of U.S. offices. With these, we explored whether long-term VOC emission rates were related to the AER over the sector, as has been observed in the short term for some VOCs in single buildings. We fit and compared two statistical models to the data. In the independent emissions model (IEM), emissions were unaffected by other variables, while in the dependent emissions model (DEM), emissions responded to the AER via coupling through a conceptual boundary layer between the air and a lumped emission source. For 20 of 46 VOCs, the DEM was preferable to the IEM and emission rates, though variable, were higher in buildings with higher AERs. Most oxygenated VOCs and some alkanes were well fit by the DEM, while nearly all aromatics and halocarbons were independent. Trends by vapor pressure suggested multiple mechanisms could be involved. The factors of temperature, relative humidity, and building age were almost never associated with effective emission rates. Our findings suggest that effective emissions in real commercial buildings will be difficult to predict from deterministic experiments or models.

  16. Estimation of VOC emissions from produced-water treatment ponds in Uintah Basin oil and gas field using modeling techniques

    Science.gov (United States)

    Tran, H.; Mansfield, M. L.; Lyman, S. N.; O'Neil, T.; Jones, C. P.

    2015-12-01

    Emissions from produced-water treatment ponds are poorly characterized sources in oil and gas emission inventories that play a critical role in studying elevated winter ozone events in the Uintah Basin, Utah, U.S. Information gaps include un-quantified amounts and compositions of gases emitted from these facilities. The emitted gases are often known as volatile organic compounds (VOCs) which, beside nitrogen oxides (NOX), are major precursors for ozone formation in the near-surface layer. Field measurement campaigns using the flux-chamber technique have been performed to measure VOC emissions from a limited number of produced water ponds in the Uintah Basin of eastern Utah. Although the flux chamber provides accurate measurements at the point of sampling, it covers just a limited area of the ponds and is prone to altering environmental conditions (e.g., temperature, pressure). This fact raises the need to validate flux chamber measurements. In this study, we apply an inverse-dispersion modeling technique with evacuated canister sampling to validate the flux-chamber measurements. This modeling technique applies an initial and arbitrary emission rate to estimate pollutant concentrations at pre-defined receptors, and adjusts the emission rate until the estimated pollutant concentrations approximates measured concentrations at the receptors. The derived emission rates are then compared with flux-chamber measurements and differences are analyzed. Additionally, we investigate the applicability of the WATER9 wastewater emission model for the estimation of VOC emissions from produced-water ponds in the Uintah Basin. WATER9 estimates the emission of each gas based on properties of the gas, its concentration in the waste water, and the characteristics of the influent and treatment units. Results of VOC emission estimations using inverse-dispersion and WATER9 modeling techniques will be reported.

  17. Volatile Organic Compound (VOC) emissions from feedlot pen surface materials as affected by within pen location, moisture, and temperature

    Science.gov (United States)

    A laboratory study was conducted to evaluate the effects of pen location, moisture, and temperature on emissions of volatile organic compounds (VOC) from surface materials obtained from feedlot pens where beef cattle were fed a diet containing 30% wet distillers grain plus solubles. Surface material...

  18. On-Road Measurement of Vehichle VOC Emission Measurements During the 2003 Mexico City Metropolitan Area Field Campaign

    Science.gov (United States)

    Knighton, W. B.; Rogers, T.; Grimsrud, E.; Herndon, S.; Allwine, E.; Lamb, B.; Velasco, E.; Westberg, H.

    2004-12-01

    In the spring of 2003 (April 1-May 5), a multinational team of experts conducted an intensive, five-week field campaign in the Mexico City Metropolitan Area (MCMA). The overall goal of this effort was to contribute to the understanding of the air quality problem in megacities. As part of the campaign the Aerodyne Mobile Laboratory was equipped with state-of-the-art analytical instruments and deployed for measuring a variety of vehicle emissions in real time including CO2, NO2, NH3, HCHO, VOC's and volatile (at 600 °C) aerosol. The on-road measurement of vehicle VOC emissions were performed using a commercial version of the IONICON PTR-MS modified to operate onboard the mobile lab platform. A summary of the PTR-MS results from these and supporting laboratory experiments will be presented and discussed. In particular, selected chase events will be presented to illustrate the utility of the PTR-MS technique for characterizing vehicle VOC emission profiles in real time. VOC emission profiles for different vehicle engine types which include gasoline, diesel and compressed natural gas will be discussed and compared to the measurements from other high time response instruments deployed on the Aerodyne mobile van.

  19. Light-Duty GDI Vehicle PM and VOC Speciated Emissions at Differing Ambient Temperatures with Ethanol Blend Gasoline

    Science.gov (United States)

    With the rise in the use of ethanol-blend gasoline in the US and more manufacturers implementing gasoline direct injection (GDI) technologies, interest is increasing in how these fuel blends affect PM and VOC emissions in GDI technology vehicles. EPA conducted a study characteri...

  20. Surface application of soybean peroxidase and calcium peroxide for reducing odorous VOC emissions from swine manure slurry

    Science.gov (United States)

    A laboratory experiment was conducted to evaluate and compare topical and fully mixed treatments of soybean peroxidase and calcium peroxide (SBP/CaO2) for reducing odorous volatile organic compound (VOC) emissions from swine manure slurry. The five treatments consisted of a control, the fully mixed ...

  1. Prediction of short-term and long-term VOC emissions from SBR bitumen-backed carpet under different temperatures

    NARCIS (Netherlands)

    Yang, X.; Chen, Q.; Bluyssen, P.M.

    1998-01-01

    This paper presents two models for volatile organic compound (VOC) emissions from carpet. One is a numerical model using the computational fluid dynamics (CFD) tech-nique for short-term predictions, the other an analytical model for long-term predictions. The numerical model can (1) deal with carpet

  2. Prediction of short-term and long-term VOC emissions from SBR bitumen-backed carpet under different temperatures

    NARCIS (Netherlands)

    Yang, X.; Chen, Q.; Bluyssen, P.M.

    1998-01-01

    This paper presents two models for volatile organic compound (VOC) emissions from carpet. One is a numerical model using the computational fluid dynamics (CFD) tech-nique for short-term predictions, the other an analytical model for long-term predictions. The numerical model can (1) deal with

  3. NERO-The Neutron Emission Ratio Observer

    Science.gov (United States)

    Lorusso, Giuseppe; Pereira, Jorque; Hosmer, Paul; Kratz, Karl Ludvig; Montes, Fernando; Reeder, Paul; Santi, Peter; Schatz, Hendrik

    2007-10-01

    The Neutron Emission Ratio Observer (NERO), has been constructed for the use at the National Superconducting Cyclotron Laboratory to work in conjunction with the NSCL Beta Counting System in order to detect β-delayed neutrons. The design of the detector provides high and flat efficiency for a wide range of neutron energies, as well as a low neutron background.

  4. Hydrogen sulphide, odor, and VOC air emission control systems for heavy oil storage, transport, and processing operations

    Energy Technology Data Exchange (ETDEWEB)

    Tandon, H.P. [APC Technologies, Inc. (Canada)

    2011-07-01

    In the heavy oil industry, companies have to control their air emissions in compliance with regulatory and process improvement objectives. The industry therefore operates air emission control systems to eliminate odor complaints, reduce personnel exposure to H2S and remove BTEX and VOC emissions. This paper studies different cases of companies which have chosen to use a fixed activated carbon adsorption unit. The study was conducted on three cases of heavy oil industries which installed the CarbonPure adsorption system and describes their objectives, processes, emissions, technology options and performances. Results showed an elimination of odor complaints, a reduction of personnel exposure to harmful air contaminants and a reduction of VOC concentrations in a reliable, low maintenance and economic manner. This study presents the greater benefits of the CarbonPure adsorption system combined with an ultra high efficiency unit over those of other adsorption systems.

  5. Leaf level VOC emissions of single plants from Amazonian and Mediterranean ecosystems: Ontogeny and flooding as stress factor for VOC emissions

    OpenAIRE

    Bracho Nunez, Araceli

    2010-01-01

    Die Vegetation ist die wichtigste Quelle von organischen flüchtigen Verbindungen (auf Englisch volatile organic compounds,VOCs), die einen bemerkenswerten Einfluss auf der Chemie und Physik der Atmosphäre haben. VOCs beeinflussen die oxidative Kapazität der Atmosphäre und tragen zu der Bildung und zum Wachstum von sekundären organischen Aerosolen bei, welche einerseits eine Streuung und Reflektierung der Energie verursachen und andererseits sich an der Bildung und Entwicklung von Wolken betei...

  6. Emissions of volatile hydrocarbons (VOC) during drying of sawdust; Utslaepp av laettflyktiga kolvaeten vid torkning av biobraenslen

    Energy Technology Data Exchange (ETDEWEB)

    Granstroem, Karin

    2001-08-01

    In the project 'Emissions of volatile hydrocarbons (VOC) during drying of sawdust' the identity, amount and composition of monoterpenes found in the drying medium of a fluidized bed drier drying sawdust from Norwegian spruce and Scotch pine has been determined. The energy efficiency of the drier has also been measured. The aim of this project was to reduce both emissions and energy required for drying, to minimize environmental and health hazards, and make drying more competitive. This would help our primary target group - small scale saw mills - to make use of the sawdust produced as a by- product by making pellets and briquettes. If the VOC remains in the sawdust its energy content will improve and therefore also its value as a fuel. The sawdust was dried to different moisture levels in a spouted bed drier at atmospheric pressure, using either recirculating or not recirculating drying medium with temperatures 140, 170 or 200 deg C. The emissions of VOC were measured using a flame ionization detector (FID) and the nature of the emissions analyzed with a gas chromatograph with mass spectrometric detector (GC-MS). The GC-MS data is reported as emitted substance per oven dry weight (odw). Experiments show that terpenes do not leave the sawdust in great amounts until it is dried to a moisture content (water/total weight) below 10%. When sawdust is dried to a predetermined moisture level, the terpene emissions increase when warmer incoming drying medium is used. The monoterpenes found in greatest amount are a-pinene, b-pinene, 3-carene, limonene and myrcene. y-terpinene was detected in emissions from pine but not from spruce. The relative amounts of different monoterpenes did not vary significantly with post-drying moisture content, but drying medium of higher temperature caused an increase in the relative amount of less volatile monoterpenes. The FID data is reported as concentration of VOC in the drying medium, and as weight VOC per odw. The concentration

  7. VOCs emission rate estimate for complicated industrial area source using an inverse-dispersion calculation method: A case study on a petroleum refinery in Northern China.

    Science.gov (United States)

    Wei, Wei; Lv, Zhaofeng; Yang, Gan; Cheng, Shuiyuan; Li, Yue; Wang, Litao

    2016-11-01

    This study aimed to apply an inverse-dispersion calculation method (IDM) to estimate the emission rate of volatile organic compounds (VOCs) for the complicated industrial area sources, through a case study on a petroleum refinery in Northern China. The IDM was composed of on-site monitoring of ambient VOCs concentrations and meteorological parameters around the source, calculation of the relationship coefficient γ between the source's emission rate and the ambient VOCs concentration by the ISC3 model, and estimation of the actual VOCs emission rate from the source. Targeting the studied refinery, 10 tests and 8 tests were respectively conducted in March and in June of 2014. The monitoring showed large differences in VOCs concentrations between background and downwind receptors, reaching 59.7 ppbv in March and 248.6 ppbv in June, on average. The VOCs increases at receptors mainly consisted of ethane (3.1%-22.6%), propane (3.8%-11.3%), isobutane (8.5%-10.2%), n-butane (9.9%-13.2%), isopentane (6.1%-12.9%), n-pentane (5.1%-9.7%), propylene (6.1-11.1%) and 1-butylene (1.6%-5.4%). The chemical composition of the VOCs increases in this field monitoring was similar to that of VOCs emissions from China's refineries reported, which revealed that the ambient VOCs increases were predominantly contributed by this refinery. So, we used the ISC3 model to create the relationship coefficient γ for each receptor of each test. In result, the monthly VOCs emissions from this refinery were calculated to be 183.5 ± 89.0 ton in March and 538.3 ± 281.0 ton in June. The estimate in June was greatly higher than in March, chiefly because the higher environmental temperature in summer produced more VOCs emissions from evaporation and fugitive process of the refinery. Finally, the VOCs emission factors (g VOCs/kg crude oil refined) of 0.73 ± 0.34 (in March) and 2.15 ± 1.12 (in June) were deduced for this refinery, being in the same order with previous direct

  8. Efficiency of catalytic processes for the reduction of CO and VOC emissions from wood combustion in domestic fireplaces

    Energy Technology Data Exchange (ETDEWEB)

    Ozil, Fabien; Tschamber, V.; Trouve, G. [Universite de haute Alsace - Laboratoire Gestion des Risques Environnement, 25 rue de Chemnitz, 68200 Mulhouse (France); Haas, Frederic (FONDIS SA, ZI Vieux Thann, 68801 Thann Cedex France)

    2009-09-15

    Pollutant characterization of domestic fireplaces, according to two paces of functioning (normal and low-charge phase) was performed. Two catalysts supported on cordierite or metal were placed in the exhaust of two domestic fireplaces (old and new generation) in order to reduce gaseous pollutants. Active phase of catalysts is composed of noble metals (Pd, Pt) and cerium. Methane was the dominant compound of the released Volatile Organic Compounds (VOC, 80% b. v.). Products resulting from incomplete combustion (CO and other VOC) did not represent more than 6% of the initial carbon content in wood. Lower concentration of CO in the exhaust was obtained with the new generation fireplace as compared to the older one with mean concentrations of CO normalized for 13% oxygen b.v. equal to 0.12% and 0.3%, respectively. Emission of VOC is also drastically reduced for new generation fireplace. The presence of a catalyst induced a decrease of the CO and VOC emission factors during ignition and low-charge phases by factors ranging from 65% to 70%. The abatement of VOC for the old generation fireplace was better in the presence of metal as compared to cordierite, with efficiency values of 65% and 30%, respectively. The new fireplace was the one on which the addition of the cleanup implements had most impact. Besides the introduction of a catalyst, a heating system of the fume was set up below the catalyst. This heating system allowed a faster activation of the catalyst, particularly during ignition and low-charge phases. Best abatements were obtained with the heated metallic support with values close to 80% and 94% for VOC and CO respectively. (author)

  9. Impacts of simulated herbivory on VOC emission profiles from coniferous plants

    Directory of Open Access Journals (Sweden)

    C. L. Faiola

    2014-09-01

    Full Text Available The largest global source of volatile organic compounds (VOCs in the atmosphere is from biogenic emissions. Plant stressors associated with a changing environment can alter both the quantity and composition of the compounds that are emitted. This study investigated the effects of one global change stressor, increased herbivory, on plant emissions from five different coniferous species: bristlecone pine (Pinus aristata, blue spruce (Picea pungens, western redcedar (Thuja plicata, grand fir (Abies grandis, and Douglas-fir (Pseudotsugas menziesii. Herbivory was simulated in the laboratory via exogenous application of methyl jasmonate, an herbivory proxy. Gas-phase species were measured continuously with a gas chromatograph coupled to a mass spectrometer and flame ionization detector (GC-MS-FID. Stress responses varied between the different plant types and even between experiments using the same set of saplings. The compounds most frequently impacted by the stress treatment were alpha-pinene, beta-pinene, 1,8-cineol, beta-myrcene, terpinolene, limonene, and the cymene isomers. Individual compounds within a single experiment often exhibited a different response to the treatment from one another.

  10. Impacts of simulated herbivory on VOC emission profiles from coniferous plants

    Science.gov (United States)

    Faiola, C. L.; Jobson, B. T.; VanReken, T. M.

    2014-09-01

    The largest global source of volatile organic compounds (VOCs) in the atmosphere is from biogenic emissions. Plant stressors associated with a changing environment can alter both the quantity and composition of the compounds that are emitted. This study investigated the effects of one global change stressor, increased herbivory, on plant emissions from five different coniferous species: bristlecone pine (Pinus aristata), blue spruce (Picea pungens), western redcedar (Thuja plicata), grand fir (Abies grandis), and Douglas-fir (Pseudotsugas menziesii). Herbivory was simulated in the laboratory via exogenous application of methyl jasmonate, an herbivory proxy. Gas-phase species were measured continuously with a gas chromatograph coupled to a mass spectrometer and flame ionization detector (GC-MS-FID). Stress responses varied between the different plant types and even between experiments using the same set of saplings. The compounds most frequently impacted by the stress treatment were alpha-pinene, beta-pinene, 1,8-cineol, beta-myrcene, terpinolene, limonene, and the cymene isomers. Individual compounds within a single experiment often exhibited a different response to the treatment from one another.

  11. Emissions of volatile organic compounds (VOCs) from the food and drink industries of the European community

    Science.gov (United States)

    Passant, Neil R.; Richardson, Stephen J.; Swannell, Richard P. J.; Gibson, N.; Woodfield, M. J.; van der Lugt, Jan Pieter; Wolsink, Johan H.; Hesselink, Paul G. M.

    Estimates were made of the amounts of volatile organic compounds (VOCs) released into the atmosphere as a result of the industrial manufacture and processing of food and drink in the European Community. The estimates were based on a review of literature sources, industrial and government contacts and recent measurements. Data were found on seven food manufacturing sectors (baking, vegetable oil extraction, solid fat processing, animal rendering, fish meal processing, coffee production and sugar beet processing) and three drink manufacturing sectors (brewing, spirit production and wine making). The principle of a data quality label is advocated to illustrate the authors' confidence in the data, and to highlight areas for further research. Emissions of ethanol from bread baking and spirit maturation were found to be the principle sources. However, significant losses of hexane and large quantities of an ill-defined mixture of partially oxidized hydrocarbons were noted principally from seed oil extraction and the drying of plant material, respectively. This latter mixture included low molecular weight aldehydes, carboxylic acids, ketones, amines and esters. However, the precise composition of many emissions were found to be poorly understood. The total emission from the food and drink industry in the EC was calculated as 260 kt yr -1. However, many processes within the target industry were found to be completely uncharacterized and therefore not included in the overall estimate (e.g. soft drink manufacture, production of animal food, flavourings, vinegar, tea, crisps and other fried snacks). Moreover, the use of data quality labels illustrated the fact that many of our estimates were based on limited data. Hence, further emissions monitoring is recommended from identified sources (e.g. processing of sugar beet, solid fat and fish meal) and from uncharacterized sources.

  12. Initial Analysis of VOCs Speciation in CREATE Emissions Inventory using the MAPS-Seoul Aircraft Field Campaign

    Science.gov (United States)

    Bu, C.; Woo, J. H.; Lee, Y.; Kim, J.; Choi, K. C.; Kim, Y.; Kim, J.; Jang, Y. K.; Kim, S.

    2016-12-01

    As the first international cooperative air quality field study, the MAPS-Seoul (Megacity Air Pollution Studies-Seoul) aircraft mission was conducted in May - June 2016 over the South Korea, to understand of climate and atmospheric environment. The aircraft carried observation instruments for measurements of GHGs, ozone and its precursors, aerosols, and chemical tracers. The CREATE (Comprehensive Regional Emissions inventory for Atmospheric Environment) emissions inventory and SMOKE-Asia emission processing system were used to support chemical forecasting and to serve as a priori for evaluation. Initial results of comparison studies show large discrepancies in VOC species over the South Korea - especially over urban regions. Several VOC species observed high near megacities and petro-chemical plants but under-predicted by chemical transport models (CTMs) - possibly due to relatively low emissions. The chemical speciation profiles and emissions inventory for each emission sources, therefore, have to be re-visited to improve emissions information. In this study, we have; 1) re-examined our emissions inventory and emission speciation processes, 2) and tried to find possible missing sources and alternative chemical speciation profiles, to improve our modelling emissions inventory. Initial review of the mapping and classification profiles, the original US chemical speciation profiles were found to be low in partitioning painting and surface coating sources, although they are the very significant contributors. Unlike other major national cities in China, Shanghai's VOC emissions fraction seems very similar to that of Seoul. Continuous analysis of major urban and industrial areas of the country will be presented at site.Acknowledgements : This subject is supported by Korea Ministry of Environment as "Climate Change Correspondence Program". This work was supported by a grant from the National Institute of Environment Research (NIER), funded by the Ministry of Environment

  13. Speciated OVOC and VOC emission inventories and their implications for reactivity-based ozone control strategy in the Pearl River Delta region, China.

    Science.gov (United States)

    Ou, Jiamin; Zheng, Junyu; Li, Rongrong; Huang, Xiaobo; Zhong, Zhuangmin; Zhong, Liuju; Lin, Hui

    2015-10-15

    The increasing ground-ozone (O3) levels, accompanied by decreasing SO2, NO2, PM10 and PM2.5 concentrations benefited from air pollution control measures implemented in recent years, initiated a serious challenge to control Volatile Organic Compound (VOC) emissions in the Pearl River Delta (PRD) region, China. Speciated VOC emission inventory is fundamental for estimating Ozone Formation Potentials (OFPs) to identify key reactive VOC species and sources in order to formulate efficient O3 control strategies. With the use of the latest bulk VOC emission inventory and local source profiles, this study developed the PRD regional speciated Oxygenated Volatile Organic Compound (OVOC) and VOC emission inventories to identify the key emission-based and OFP-based VOC sources and species. Results showed that: (1) Methyl alcohol, acetone and ethyl acetate were the major constituents in the OVOC emissions from industrial solvents, household solvents, architectural paints and biogenic sources; (2) from the emission-based perspective, aromatics, alkanes, OVOCs and alkenes made up 39.2%, 28.2%, 15.9% and 10.9% of anthropogenic VOCs; (3) from the OFP-based perspective, aromatics and alkenes become predominant with contributions of 59.4% and 25.8% respectively; (4) ethene, m/p-xylene, toluene, 1,2,4-trimethyl benzene and other 24 high OFP-contributing species were the key reactive species that contributed to 52% of anthropogenic emissions and up to 80% of OFPs; and (5) industrial solvents, industrial process, gasoline vehicles and motorcycles were major emission sources of these key reactive species. Policy implications for O3 control strategy were discussed. The OFP cap was proposed to regulate VOC control policies in the PRD region due to its flexibility in reducing the overall OFP of VOC emission sources in practice.

  14. Screening the Emission Sources of Volatile Organic Compounds (VOCs) in China Based on Multi-effect Evaluation

    Science.gov (United States)

    Niu, H., Jr.

    2015-12-01

    Volatile organic compounds (VOCs) in the atmosphere have adverse impacts via three main pathways: photochemical ozone formation, secondary organic aerosol production, and direct toxicity to humans. Few studies have integrated these effects to prioritize control measures for VOCs sources. In this study, we developed a multi-effect evaluation methodology based on updated emission inventories and source profiles, which was combined with ozone formation potential (OFP), secondary organic aerosol potential (SOAP), and VOC toxicity data to identify important emission sources and key species. We derived species-specific emission inventories for 152 sources. The OFPs, SOAPs, and toxicity of each source were determined, and the contribution and share of each source to each of these adverse effects was calculated. Weightings were given to the three adverse effects by expert scoring, and the integrated impact was determined. Using 2012 as the base year, solvent usage and industrial process were found to be the most important anthropogenic sources, accounting for 24.2 and 23.1% of the integrated environmental effect, respectively. This was followed by biomass burning, transportation, and fossil fuel combustion, all of which had a similar contribution ranging from 16.7 to 18.6%. The top five industrial sources, including plastic products, rubber products, chemical fiber products, the chemical industry, and oil refining, accounted for nearly 70.0% of industrial emissions. In China, emissions reductions are required for styrene, toluene, ethylene, benzene, and m/p-xylene. The 10 most abundant chemical species contributed 76.5% of the integrated impact. Beijing, Chongqing, Shanghai, Jiangsu, and Guangdong were the five leading provinces when considering the integrated effects. Besides, the chemical mass balance model (CMB) was used to verify the VOCs inventories of 47 cities in China, so as to optimize our evaluation results. We suggest that multi-effect evaluation is necessary to

  15. Efficient control of odors and VOC emissions via activated carbon technology.

    Science.gov (United States)

    Mohamed, Farhana; Kim, James; Huang, Ruey; Nu, Huong Ton; Lorenzo, Vlad

    2014-07-01

    This research study was undertaken to enhance the efficiency and economy of carbon scrubbers in controlling odors and volatile organic compounds (VOCs) at the wastewater collection and treatment facilities of the Bureau of Sanitation, City of Los Angeles. The butane activity and hydrogen sulfide breakthrough capacity of activated carbon were assessed. Air streams were measured for odorous gases and VOCs and removal efficiency (RE) determined. Carbon towers showed average to excellent removal of odorous compounds, VOCs, and siloxanes; whereas, wet scrubbers demonstrated good removal of odorous compounds but low to negative removal of VOCs. It was observed that the relative humidity and empty bed contact time are one of the most important operating parameters of carbon towers impacting the pollutant RE. Regular monitoring of activated carbon and VOCs has resulted in useful information on carbon change-out frequency, packing recommendations, and means to improve performance of carbon towers.

  16. Emissions and photochemistry of oxygenated VOCs in urban plumes in the Northeastern United States

    Directory of Open Access Journals (Sweden)

    R. Sommariva

    2011-07-01

    Full Text Available Photochemical processes inside urban plumes in the Northeast of the United States have been studied using a highly detailed chemical model, based upon the Master Chemical Mechanism (MCM. The model results have been compared to measurements of oxygenated VOCs (acetone, methyl ethyl ketone, acetaldehyde, acetic acid and methanol obtained during several flights of the NOAA WP-3D aircraft, which sampled plumes from the New York City area during the ICARTT campaign in 2004. The agreement between the model and the measurements was within 40–60 % for all species, except acetic acid.

    The model results have been used to study the formation and photochemical evolution of acetone, methyl ethyl ketone and acetaldehyde. Under the conditions encountered during the ICARTT campaign, acetone is produced from the oxidation of propane (24–28 % and i-propanol (<15 % and from a number of products of i-pentane oxidation. Methyl ethyl ketone (MEK is mostly produced from the oxidation of n-butane (20–30 % and 3-methylpentane (<40 %. Acetaldehyde is formed from several precursors, mostly small alkenes, >C5 alkanes, propanal and MEK. Ethane and ethanol oxidation account, respectively, for 6–23 % and 5–25 % of acetaldehyde photochemical formation. The results highlight the importance of alkanes for the photochemical production of ketones and the role of hydroperoxides in sustaining their formation far from the emission sources.

  17. Emissions and photochemistry of oxygenated VOCs in urban plumes in the Northeastern United States

    Directory of Open Access Journals (Sweden)

    R. Sommariva

    2008-06-01

    Full Text Available Photochemical processes inside urban plumes in the Northeast of the United States have been studied using a highly detailed chemical model, based upon the Master Chemical Mechanism (MCM. The model results have been compared to measurements of oxygenated VOCs (acetone, methyl ethyl ketone, acetaldehyde, acetic acid and methanol obtained during several flights of the NOAA WP-3D aircraft, which sampled plumes from the New York City area during the ICARTT campaign in 2004. The agreement between the model and the measurements was within 40–60% for all species, except acetic acid.

    The model results have been used to study the formation and photochemical evolution of acetone, methyl ethyl ketone and acetaldehyde. Under the conditions encountered during the ICARTT campaign, acetone is produced from the oxidation of propane (24–28% and i-propanol (<15% and from a number of products of i-pentane oxidation. Methyl ethyl ketone (MEK is mostly produced from the oxidation of n-butane (20–30% and 3-methylpentane (<40%. Acetaldehyde is formed from several precursors, mostly small alkenes, >C5 alkanes, propanal and MEK. Ethane and ethanol oxidation account, respectively, for 6–23% and 5–25% of acetaldehyde photochemical formation. The results highlight the importance of long-chain alkanes for the photochemical production of ketones and the role of hydroperoxides in sustaining their formation far from the emission sources.

  18. Effects of different mixing ratios on emissions from passenger cars fueled with methanol/gasoline blends.

    Science.gov (United States)

    Zhao, Hong; Ge, Yunshan; Tan, Jianwei; Yin, Hang; Guo, Jiadong; Zhao, Wei; Dai, Peipei

    2011-01-01

    Regulated and unregulated emissions from four passenger cars fueled with methanol/gasoline blends at different mixing ratios (M15, M20, M30, M50, M85 and M100) were tested over the New European Driving Cycle (NEDC). Volatile organic compounds (VOCs) were sampled by Tenax TA and analyzed by thermal desorption-gas chromatograph/mass spectrometer (TD-GC/MS). Carbonyls were trapped on dinitrophenylhydrazine (DNPH) cartridges and analyzed by high performance liquid chromatography (HPLC). The results showed that total emissions of VOCs and BTEX (benzene, toluene, ethylbenzene, p, m, o-xylene) from all vehicles fueled with methanol/gasoline blends were lower than those from vehicles fueled with only gasoline. Compared to the baseline, the use of M85 decreased BTEX emissions by 97.4%, while the use of M15 decreased it by 19.7%. At low-to-middle mixing ratios (M15, M20, M30 and M50), formaldehyde emissions showed a slight increase while those of high mixing ratios (M85 and M100) were three times compared with the baseline gasoline only. When the vehicles were retrofitted with new three-way catalytic converters (TWC), emissions of carbon monoxide (CO), total hydrocarbon (THC), and nitrogen oxides (NO(x)) were decreased by 24%-50%, 10%-35%, and 24%-58% respectively, compared with the cars using the original equipment manufacture (OEM) TWC. Using the new TWC, emissions of formaldehyde and BTEX were decreased, while those of other carbonyl increased. It is necessary that vehicles fueled with methanol/gasoline blends be retrofitted with a new TWC. In addition, the specific reactivity of emissions of vehicles fueled with M15 and retrofitted with the new TWC was reduced from 4.51 to 4.08 compared to the baseline vehicle. This indicates that the use of methanol/gasoline blend at a low mixing ratio may have lower effect on environment than gasoline.

  19. A three year study on 14 VOCs at one site in Rome: levels, seasonal variations, indoor/outdoor ratio and temporal trends.

    Science.gov (United States)

    Fuselli, Sergio; De Felice, Marco; Morlino, Roberta; Turrio-Baldassarri, Luigi

    2010-10-01

    Fourteen volatile organic compounds (VOCs)-twelve hydrocarbons and two organochlorine compounds-were monitored both outdoors and indoors for three years at one site in Rome. Results showed that 118 out of 168 indoor seasonal mean values were higher than the corresponding outdoor concentrations. The most relevant source of outdoor hydrocarbons was automotive exhaust emissions. Due to the enforcement of various measures to protect health and the environment, outdoor levels of monoaromatic hydrocarbons decreased about ten fold over 15 years, and aliphatic hydrocarbons also decreased. With the decrease in these outdoor concentrations, indoor air sources are likely to be more relevant for indoor air exposures. Winter outdoor values for monoaromatic hydrocarbons were generally markedly higher than the summer ones. The gradual replacement of the current fleet of circulating cars with new cars complying with EURO 5 standards, further reducing hydrocarbon emissions, may possibly lead to an increase in the observed indoor/outdoor ratios. It is indeed more difficult to remove indoor sources, some of which are still unknown.

  20. Stable Carbon Isotope Ratios in Atmospheric VOC across the Asian Summer Monsoon Anticyclone obtained during the OMO-ASIA campaign

    Science.gov (United States)

    Krebsbach, Marc; Koppmann, Ralf; Meisehen, Thomas

    2017-04-01

    The automated high volume air sampling system (MIRAH) has been deployed during the atmospheric measurement campaign OMO-ASIA (Oxidation Mechanism Observations) with the German High Altitude - Long-range research aircraft (HALO) in July and August 2015. The intensive measurement period with base stations in Paphos (Cyprus) and Gan (Maldives) focussed on oxidation processes and air pollution chemistry downwind of the South Asia summer monsoon anticyclone, a pivot area critical for air quality and climate change, both regionally and worldwide. The measurement region covered the Eastern Mediterranean region, the Arabian Peninsula, Egypt, and the Arabian Sea. In total 194 air samples were collected on 17 flights in a height region from 3 km up to 15 km. The air samples were analysed for stable carbon isotope ratios in VOC with GC-C-IRMS in the laboratory afterwards. We determined stable carbon isotope ratios and mixing ratios of several aldehydes, ketones, alcohols, and aromatics. The large extent of the investigated area allowed for encountering air masses with different origin, characteristic, and atmospheric processing, e.g. Mediterranean air masses, crossing of polluted filaments and remnants of the Asian monsoon outflow, split of the Asian monsoon anticyclone. In this presentation we will show first results and interpretations supported by HYSPLIT backward trajectories.

  1. Biological anoxic treatment of O{sub 2}-free VOC emissions from the petrochemical industry: A proof of concept study

    Energy Technology Data Exchange (ETDEWEB)

    Muñoz, Raúl; Souza, Theo S.O. [Department of Chemical Engineering and Environmental Technology, University of Valladolid, Dr Mergelina s/n, 47011 Valladolid (Spain); Glittmann, Lina [Ostfalia University of Applied Sciences, Department of Supply Engineering, Wolfenbüttel (Germany); Pérez, Rebeca [Department of Chemical Engineering and Environmental Technology, University of Valladolid, Dr Mergelina s/n, 47011 Valladolid (Spain); Quijano, Guillermo, E-mail: gquijano@iq.uva.es [Department of Chemical Engineering and Environmental Technology, University of Valladolid, Dr Mergelina s/n, 47011 Valladolid (Spain)

    2013-09-15

    Highlights: • The treatment of O{sub 2}-free VOC emissions can be done by means of denitrifying processes. •Toluene vapors were successfully removed under anoxic denitrifying conditions. • A high bacterial diversity was observed. • Actinobacteria and Proteobacteria were the predominant phyla. • The nature and number of metabolites accumulated varied with the toluene load -- Abstract: An innovative biofiltration technology based on anoxic biodegradation was proposed in this work for the treatment of inert VOC-laden emissions from the petrochemical industry. Anoxic biofiltration does not require conventional O{sub 2} supply to mineralize VOCs, which increases process safety and allows for the reuse of the residual gas for inertization purposes in plant. The potential of this technology was evaluated in a biotrickling filter using toluene as a model VOC at loads of 3, 5, 12 and 34 g m{sup −3} h{sup −1} (corresponding to empty bed residence times of 16, 8, 4 and 1.3 min) with a maximum elimination capacity of ∼3 g m{sup −3} h{sup −1}. However, significant differences in the nature and number of metabolites accumulated at each toluene load tested were observed, o- and p-cresol being detected only at 34 g m{sup −3} h{sup −1}, while benzyl alcohol, benzaldehyde and phenol were detected at lower loads. A complete toluene removal was maintained after increasing the inlet toluene concentration from 0.5 to 1 g m{sup −3} (which entailed a loading rate increase from 3 to 6 g m{sup −3} h{sup −1}), indicating that the system was limited by mass transfer rather than by biological activity. A high bacterial diversity was observed, the predominant phyla being Actinobacteria and Proteobacteria.

  2. Comparison of VOC emissions between air-dried and heat-treated Norway spruce ( Picea abies), Scots pine ( Pinus sylvesteris) and European aspen ( Populus tremula) wood

    Science.gov (United States)

    Hyttinen, Marko; Masalin-Weijo, Marika; Kalliokoski, Pentti; Pasanen, Pertti

    2010-12-01

    Heat-treated wood is an increasingly popular decoration material. Heat-treatment improves dimensional stability of the wood and also prevents rot fungus growth. Although production of heat-treated wood has been rapidly increasing, there is only little information about the VOC emissions of heat-treated wood and its possible influences on indoor air quality. In the present study, VOC emissions from three untreated (air-dried) and heat-treated wood species were compared during a four weeks test period. It appeared that different wood species had clearly different VOC emission profiles. Heat-treatment was found to decrease VOC emissions significantly and change their composition. Especially, emissions of terpenes decreased from softwood samples and aldehydes from European aspen samples. Emissions of total aldehydes and organic acids were at the same level or slightly higher from heat treated than air-dried softwood samples. In agreement with another recent study, the emissions of furfural were found to increase and those of hexanal to decrease from all the wood species investigated. In contrast to air-dried wood samples, emissions of VOCs were almost in steady state from heat treated wood samples even in the beginning of the test.

  3. Assessment of the impact of biogenic VOC emissions in a high ozone episode via integrated remote sensing and the CMAQ model

    Institute of Scientific and Technical Information of China (English)

    Kaiyu CHENG; Ni-Bin CHANG

    2009-01-01

    In many metropolitan regions, natural sources contribute a substantial fraction of volatile organic compound (VOC) emissions. These biogenic VOC emissions are precursors to tropospheric Ozone (O3) formation.Because forests make up 59% of the land area in Taiwan Province, China, the biogenic VOC emissions from forests and farmland could play an important role in photochemical reactions. On the other hand, anthropogenic emissions might also be one of the major inputs for ground level O3concentrations. Hence, emission inventory data, grouped as point, area, mobile and biogenic VOC sources, are a composite of reported and estimated pollutant emission information and are used by many air quality models to simulate ground level O3 concentrations. Before using relevant air quality models, the emission inventory data generally require huge amounts of processing for spatial,temporal, and species congruence with respect to the associated air quality modeling work. The fist part of this research applied satellite remote sensing and geographic information system (GIS) analyses to characterize land use/land cover (LULC) patterns, integrating various sources of anthropogenic emissions and biogenic emissions associated with a variety of plant species. To investigate the significance of biogenic VOC emissions on ozone formation, meteorological and air quality modeling were then employed to generate hourly ozone estimates for a case study of a high ozone episode in southern Taiwan, which is the leading industrial hub on the island. To enhance the modeling accuracy, a unique software module, SMOKE, was set up for emission processing to prepare emission inputs for the U.S. EPA's Models-3/CMAQ. An emission inventory of Taiwan,TEDS 4.2, was used as the anthropogenic emission inventory. Biogenic emission modeling was accomplished by BEIS-2 in SMOKE, with improvement of local LULC data and revised emission factors. Research findings show that the majority of biogenic VOC emissions occur

  4. Comparison of emission ratios from on-road sources using a mobile laboratory under various driving and operational sampling modes

    Directory of Open Access Journals (Sweden)

    M. Zavala

    2008-04-01

    Full Text Available Mobile sources produce a significant fraction of the total anthropogenic emissions burden in large cities and have harmful effects on air quality at multiple spatial scales. Mobile emissions are intrinsically difficult to estimate due to the large number of parameters affecting the emissions variability within and across vehicles types. The MCMA-2003 Campaign in Mexico City has showed the utility of using a mobile laboratory to sample and characterize specific classes of motor vehicles to better quantify their emissions characteristics as a function of their driving cycles. The technique clearly identifies "high emitter" vehicles via individual exhaust plumes, and also provides fleet average emission rates. We have applied this technique to Mexicali during the Border Ozone Reduction and Air Quality Improvement Program for the Mexicali-Imperial Valley in 2005. In this paper we analyze the variability of measured emission ratios for emitted NOx, CO, specific VOCs, NH3, and some primary fine particle components and properties obtained during the Border Ozone Reduction and Air Quality Improvement Program for the Mexicali-Imperial Valley in 2005 by deploying a mobile laboratory in roadside stationary sampling, chase and fleet average operational sampling modes. The measurements reflect various driving modes characteristic of the urban fleets. The observed variability for all measured gases and particle emission ratios is greater for the chase and roadside stationary sampling than for fleet average measurements. The fleet average sampling mode captured the effects of traffic conditions on the measured on-road emission ratios, allowing the use of fuel-based emission ratios to assess the validity of traditional "bottom-up" emissions inventories. Using the measured on-road emission ratios, we estimate CO and NOx mobile emissions of 175±62 and 10.4±1.3 metric tons/day, respectively, for the gasoline vehicle fleet in

  5. Effect of resin content and substrate on the emission of BTEX and carbonyls from low-VOC water-based wall paint.

    Science.gov (United States)

    Zhao, Ping; Cheng, Yu-Hsiang; Lin, Chi-Chi; Cheng, Yu-Lin

    2016-02-01

    The primary aim of this work is to explore the effect of resin content and the effect of substrate on the emission of benzene, toluene, ethylbenzene, and xylene (BTEX) and carbonyls from low-VOC water-based wall paint. Four low-volatile organic compound (VOC) paints include paints A (20% acrylic), B (30% acrylic), C (20% polyvinyl acetate), and D (30% polyvinyl acetate) were painted on stainless steel specimen for the study of resin effect. Green calcium silicate, green cement, and stainless steel were painted with paints A and C for the study of substrate effect. Concentrations of the VOCs in the chamber decreased with the elapsed time. Both resin type and resin quantity in paint had effects on VOC emissions. Paints with acrylic resin emitted less BTEX and carbonyls than paints with polyvinyl acetate resin. However, the effects of resin quantity varied with VOCs. Porous substrates were observed to interact more strongly with paints than inert substrates. Both green calcium silicate and green cement substrates have strong power of adsorption of VOCs from wall paints, namely toluene, formaldehyde, acetaldehyde, 2-butanone, methacrolein, butyraldehyde, and benzaldehyde. Some compounds like toluene, formaldehyde, and butyaldehyde were desorbed very slowly from green calcium silicate and green cement substrates.

  6. On-site passive flux sampler measurement of emission rates of carbonyls and VOCs from multiple indoor sources

    Energy Technology Data Exchange (ETDEWEB)

    Shinohara, Naohide [Research Institute of Science for Safety and Sustainability (RISS), National Institute of Advanced Industrial Science and Technology (AIST), 16-1 Onogawa, Tsukuba City, Ibaraki 305-8569 (Japan); Kai, Yuya; Mizukoshi, Atsushi; Kumagai, Kazukiyo; Okuizumi, Yumiko; Jona, Miki; Yanagisawa, Yukio [Department of Environment Systems, Institute of Environmental Studies, Graduate School of Frontier Sciences, The University of Tokyo, 5-1-5 Kashiwa-no-ha, Kashiwa-shi, Chiba 277-8563 (Japan); Fujii, Minoru [Research Center for Material Cycles and Waste Management, National Institute for Environmental Studies, 16-2 Onogawa, Tsukuba City, Ibaraki 305-8506 (Japan)

    2009-05-15

    In indoor environments with high levels of air pollution, it is desirable to remove major sources of emissions to improve air quality. In order to identify the emission sources that contribute most to the concentrations of indoor air pollutants, we used passive flux samplers (PFSs) to measure emission rates of carbonyl compounds and volatile organic compounds (VOCs) from many of the building materials and furnishings present in a room in a reinforced concrete building in Tokyo, Japan. The emission flux of formaldehyde from a desk was high (125 {mu}g/m{sup 2}/h), whereas fluxes from a door and flooring were low (21.5 and 16.5 {mu}g/m{sup 2}/h, respectively). The emission fluxes of toluene from the ceiling and the carpet were high (80.0 and 72.3 {mu}g/m{sup 2}/h, respectively), whereas that from the flooring was low (9.09 {mu}g/m{sup 2}/h). The indoor and outdoor concentrations of formaldehyde were 61.5 and 8.64 {mu}g/m{sup 3}, respectively, and those of toluene were 43.2 and 17.5 {mu}g/m{sup 3}, respectively. The air exchange rate of the room as measured by the perfluorocarbon tracer (PFT) method was 1.84/h. Taking into consideration the area of the emission sources, the carpet, ceiling, and walls were identified as the principal emission sources, contributing 24%, 20%, and 22% of the formaldehyde, respectively, and 22%, 27%, and 14% of the toluene, respectively, assuming that the emission rate from every major emission sources could be measured. In contrast, the door, the flooring, and the desk contributed little to the indoor levels of formaldehyde (1.0%, 0.54%, and 4.1%, respectively) and toluene (2.2%, 0.31%, and 0.85%, respectively). (author)

  7. A novel method to quantify the emission and conversion of VOCs in the smoking of electronic cigarettes

    Science.gov (United States)

    Kim, Yong-Hyun; Kim, Ki-Hyun

    2015-11-01

    An analytical technique was developed for the quantitation of volatile organic compounds (VOC) in three different forms of electronic cigarette (EC): solution, vapor, and aerosol. Through the application of the mass change tracking (MCT) approach, the consumed amount of the solution was measured to track the conversion of targets between the different phases. The concentration of aerosol plus vapor (A&V) decreased exponentially (559 to 129 g m-3) with increasing puff velocity (0.05 to 1 L min-1). A strong correlation existed between sampling volume and consumed solution mass (R2 = 0.9972 ± 0.0021 (n = 4)). In the EC solution, acetic acid was considerably high (25.8 μg mL-1), along with trace quantities of some VOCs (methyl ethyl ketone, toluene, propionic acid, and i-butyric acid: 0.24 ± 0.15 μg mL-1 (n = 4)). In the aerosol samples, many VOCs (n-butyraldehyde, n-butyl acetate, benzene, xylene, styrene, n-valeric acid, and n-hexanoic acid) were newly produced (138 ± 250 μg m-3). In general, the solution-to-aerosol (S/A) conversion was significant: e.g., 1,540% for i-butyric acid. The emission rates of all targets computed based on their mass in aerosol/ consumed solution (ng mL-1) were from 30.1 (p-xylene) to 398 (methyl ethyl ketone), while those of carboxyls were much higher from 166 (acetic acid) to 5,850 (i-butyric acid).

  8. Catalytic incineration of CO and VOC emissions over supported metal oxide catalysts

    Energy Technology Data Exchange (ETDEWEB)

    Larsson, Per-Olof

    1999-05-01

    Catalytic incineration is one of the methods to reduce the emissions of CO and VOCs. Low operation temperature and low catalyst cost are essential parameters for catalytic incinerators. Pt/Al{sub 2}O{sub 3} catalysts are frequently used today, but the cheaper metal oxide catalysts can be very competitive if comparable overall activity is obtained. This thesis concerns how it is possible to decrease the operation temperature for supported metal oxide catalysts by using different supports, active metal oxides and additives. In the thesis it is demonstrated that different copper oxide based catalysts have the best activity and durability for complete oxidation among several tested metal oxide catalysts. CuO{sub x} supported on TiO{sub 2} and Al{sub 2}O{sub 3} showed increased activity with the CuO{sub x} loading up to the threshold coverage for formation of crystalline CuO particles, which is 12 {mu}mol/m{sup 2} on TiO{sub 2} and 6 {mu}mol/m{sup 2} on Al{sub 2}O{sub 3}. Up to the threshold coverage for CuO formation, well dispersed copper oxide species were formed on TiO{sub 2}, and a dispersed copper aluminate surface phase was formed on Al{sub 2}O{sub 3}. Durability tests showed accelerated sintering of TiO{sub 2} by copper, but stabilisation was possible by modification of the TiO{sub 2} with CeO{sub x} before the deposition of CuO{sub x}. The stabilisation was obtained by formation of a Ce-O-Ti surface phase. Addition of CeO{sub x} also enhanced the activity of the copper oxide species thanks to favourable interaction between the active copper oxide species and the CeO{sub x} on the support, which could be seen as increased reducibility in TPR experiments. The increased activity and reducibility was also observed for CuO{sub x} supported on ceria modified Al{sub 2}O{sub 3}. In this regard it was shown that CuO{sub x} deposited on CeO{sub 2}(001) surfaces was substantially more active for CO oxidation than copper oxide deposited on CeO{sub 2}(111) Surfaces. This

  9. The reduction of formaldehyde and VOCs emission from wood-based flooring by green adhesive using cashew nut shell liquid (CNSL).

    Science.gov (United States)

    Kim, Sumin

    2010-10-15

    To discuss the reduction of formaldehyde and volatile organic compound (VOC) emissions from engineered flooring, cashew nut shell liquid (CNSL)-formaldehyde (CF) resin and CF/PVAc resin were applied for the maple face of the veneer bonding on plywood. The CF resin was used to replace urea-formaldehyde (UF) resin in the formaldehyde-based resin system in order to reduce formaldehyde and VOC emissions from the adhesives used between the plywoods and fancy veneers. For the CF/PVAc resins, 5, 10, 20 or 30% of PVAc was added to the CF resin. The CF/PVAc resins showed better bonding than the commercial natural tannin adhesive with a higher level of wood penetration. The standard formaldehyde emission test and a VOC analyzer were used to determine the formaldehyde and VOC emissions, respectively, from the engineered floorings. The CF resin and CF/PVAc resin systems with UV coating satisfied the E(1) and E(0) grades of the Korean Standard. TVOC emission was slightly increased by the PVAc addition.

  10. Organic liquids storage tanks volatile organic compounds (VOCS) emissions dispersion and risk assessment in developing countries: the case of Dar-es-Salaam City, Tanzania.

    Science.gov (United States)

    Jackson, Msafiri M

    2006-05-01

    The emission estimation of nine volatile organic compounds (VOCs) from eight organic liquids storage tanks companies in Dar-es-Salaam City Tanzania has been done by using US EPA standard regulatory storage tanks emission model (TANKS 4.9b). Total VOCs atmospheric emission has been established to be 853.20 metric tones/yr. It has been established further that petrol storage tanks contribute about 87% of total VOCs emitted, while tanks for other refined products and crude oil were emitting 10% and 3% of VOCs respectively. Of the eight sources (companies), the highest emission value from a single source was 233,222.94 kg/yr and the lowest single source emission value was 6881.87 kg/yr. The total VOCs emissions estimated for each of the eight sources were found to be higher than the standard level of 40,000 kg/yr per source for minor source according to US EPA except for two sources, which were emitting VOCs below the standard level. The annual emissions per single source for each of the VOCs were found to be below the US EPA emissions standard which is 2,000 kg/yr in all companies except the emission of hexane from company F1 which was slightly higher than the standard. The type of tanks used seems to significantly influence the emission rate. Vertical fixed roof tanks (VFRT) emit a lot more than externally floating roof tanks (EFRT) and internally floating roof tanks (IFRT). The use of IFRT and EFRT should be encouraged especially for storage of petrol which had highest atmospheric emission contribution. Model predicted atmospheric emissions are less than annual losses measured by companies in all the eight sources. It is possible that there are other routes for losses beside atmospheric emissions. It is therefore important that waste reduction efforts in these companies are directed not only to reducing atmospheric emissions, but also prevention of the spillage and leakage of stored liquid and curbing of the frequently reported illegal siphoning of stored products

  11. On speciation of VOC localization

    Science.gov (United States)

    Chen, S.; Chang, J.; Wang, J.

    2011-12-01

    Most of the gas-phase chemical mechanisms successfully used in gas-phase atmospheric chemical processes, such as CBM-Z, RADM2 or SAPRC-07, treat hundreds of VOC as lumped organic species by their chemical characteristics. Most of the model results are compared with total VOC observations, and it is not appropriate to compare lumped VOC simulations to observations even if there are separate VOC observations like Photochemical Assessment Monitoring Stations (PAMS). While the PAMS Air Quality Model (PAMS-AQM) is developed, separate organic species observed by PAMS without a doubt can be directly compared with model simulations. From the past case study (Chen et al., 2010), it shows a major and very significant finding in that detailed emissions of VOC in the existing emissions database are often in error in Taiwan or other countries due to the fact that the annual VOC emissions are classified into hundreds of species-specific emissions by using the speciation factors following the protocol of the U.S. EPA (AP-42). Based on all PAMS observations from 2006-2007, four base cases with well comparable meteorological simulations were selected for the unified correction for all sources in Taiwan. After the PAMS species emissions are modified, the diurnal patterns and simulation-observation correlation for most of the PAMS species are improved, and the concentration levels are more comparable with those of observations. More expanded case studies also revealed necessary corrections for the PAMS species emissions. Sensitivity analyses for lumped organic species with modified PAMS species emissions are also conducted. After modified PAMS emissions are added into lumped VOC emissions, there is an increase of only 10% of totally VOC emissions. While the sources of the lumped VOC emissions are changed, ozone formation shows no significant change with modified lumped VOC emissions. This helps to support the argument that for ozone simulation, the lumped VOC processes balance out

  12. Characterization of Volatile Organic Compound (VOC) Emissions at Sites of Oil Sands Extraction and Upgrading in northern Alberta

    Science.gov (United States)

    Marrero, J.; Simpson, I. J.; Meinardi, S.; Blake, D. R.

    2011-12-01

    The crude oil reserves in Canada's oil sands are second only to Saudi Arabia, holding roughly 173 billion barrels of oil in the form of bitumen, an unconventional crude oil which does not flow and cannot be pumped without heating or dilution. Oil sands deposits are ultimately used to make the same petroleum products as conventional forms of crude oil, though more processing is required. Hydrocarbons are the basis of oil, coal and natural gas and are an important class of gases emitted into the atmosphere during oil production, particularly because of their effects on air quality and human health. However, they have only recently begun to be independently assessed in the oil sands regions. As part of the 2008 ARCTAS airborne mission, whole air samples were collected in the boundary layer above the surface mining operations of northern Alberta. Gas chromatography analysis revealed enhanced concentrations of 53 VOCs (C2 to C10) over the mining region. When compared to local background levels, the measured concentrations were enhanced up to 1.1-400 times for these compounds. To more fully characterize emissions, ground-based studies were conducted in summer 2010 and winter 2011 in the oil sands mining and upgrading areas. The data from the 200 ground-based samples revealed enhancements in the concentration of 65 VOCs. These compounds were elevated up to 1.1-3000 times above background concentrations and include C2-C8 alkanes, C1-C5 alkyl nitrates, C2-C4 alkenes and potentially toxic aromatic compounds such as benzene, toluene, and xylenes.

  13. Effects of Cold Temperature and Ethanol Content on VOC Emissions from Light-Duty Gasoline Vehicles

    Data.gov (United States)

    U.S. Environmental Protection Agency — Supporting information Table S6 provides emission rates in g/km of volatile organic compounds measured from gasoline vehicle exhaust during chassis dynamometer...

  14. Using growth and decline factors to project VOC emissions from oil and gas production.

    Science.gov (United States)

    Oswald, Whitney; Harper, Kiera; Barickman, Patrick; Delaney, Colleen

    2015-01-01

    Projecting future-year emission inventories in the oil and gas sector is complicated by the fact that there is a life cycle to the amount of production from individual wells and thus from well fields in aggregate. Here we present a method to account for that fact in support of regulatory policy development. This approach also has application to air quality modeling inventories by adding a second tier of refinement to the projection methodology. Currently, modeling studies account for the future decrease in emissions due to new regulations based on the year those regulations are scheduled to take effect. The addition of a year-by-year accounting of production decline provides a more accurate picture of emissions from older, uncontrolled sources. This proof of concept approach is focused solely on oil production; however, it could be used for the activity and components of natural gas production to compile a complete inventory for a given area.

  15. Health evaluation of volatile organic compound (VOC) emission from exotic wood products

    DEFF Research Database (Denmark)

    Kirkeskov, L; Witterseh, T; Funch, L W

    2009-01-01

    analyses by climate chamber measurement (iroko, ramin, sheesham, merbau, and rubber tree). Samples of exotic wood (rubber tree and belalu) were further analyzed for emission of chemical compounds by migration into artificial saliva and for content of pesticides and allergenic natural rubber latex (NR latex......) (rubber tree). The toxicological effects of all substances identified were evaluated and the lowest concentrations of interest (LCI) assessed. An R-value was calculated for each wood product (R-value below 1 is considered to be unproblematic as regards health). Emission from the evaluated exotic wood only...

  16. Using Multiple Regression in Estimating (semi) VOC Emissions and Concentrations at the European Scale

    DEFF Research Database (Denmark)

    Fauser, Patrik; Thomsen, Marianne; Pistocchi, Alberto

    2010-01-01

    for an in-depth risk assessment. Uncertainty measures are not available for the RAR data; however, uncertainties for the applied regression models are given in the paper. Evaluation of the methods reveals that between 79% and 93% of all emission and PEC estimates are within one order of magnitude...... of the reported RAR values. Bearing in mind that the domain of the method comprises organic industrial high-production volume chemicals, four chemicals, prioritized in the Water Framework Directive and the Stockholm Convention on Persistent Organic Pollutants, were used to test the method for estimated emissions...

  17. Root anoxia effects on physiology and emissions of volatile organic compounds (VOC) under short- and long-term inundation of trees from Amazonian floodplains.

    Science.gov (United States)

    Bracho-Nunez, Araceli; Knothe, Nina Maria; Costa, Wallace R; Maria Astrid, Liberato R; Kleiss, Betina; Rottenberger, Stefanie; Piedade, Maria Teresa Fernandez; Kesselmeier, Jürgen

    2012-01-01

    Volatile organic compound (VOC) emissions are affected by a variety of biotic and abiotic factors such as light intensity, temperature, CO2 and drought. Another stress factor, usually overlooked but very important for the Amazon region, is flooding. We studied the exchange of VOCs in relation to CO2 exchange and transpiration of 8 common tree species from the Amazonian floodplain forest grown up from seeds using a dynamic enclosure system. Analysis of volatile organics was performed by PTR-MS fast online measurements. Our study confirmed emissions of ethanol and acetaldehyde at the beginning of root anoxia after inundation, especially in less anoxia adapted species such as Vatairea guianensis, but not for Hevea spruceana probably due to a better adapted metabolism. In contrast to short-term inundation, long-term flooding of the root system did not result in any emission of ethanol or/and acetaldehyde. Emission of other VOCs, such as isoprenoids, acetone, and methanol exhibited distinct behavior related to the origin (igapó or várzea type of floodplain) of the tree species. Also physiological activities exhibited different response patterns for trees from igapó or várzea. In general, isoprenoid emissions increased within the course of some days of short-term flooding. After a long period of waterlogging, VOC emissions decreased considerably, along with photosynthesis, transpiration and stomatal conductance. However, even under long-term testing conditions, two tree species did not show any significant decrease or increase in photosynthesis. In order to understand ecophysiological advantages of the different responses we need field investigations with adult tree species.

  18. Using Multiple Regression in Estimating (semi) VOC Emissions and Concentrations at the European Scale

    DEFF Research Database (Denmark)

    Fauser, Patrik; Thomsen, Marianne; Pistocchi, Alberto

    2010-01-01

    This paper proposes a simple method for estimating emissions and predicted environmental concentrations (PECs) in water and air for organic chemicals that are used in household products and industrial processes. The method has been tested on existing data for 63 organic high-production volume che...

  19. Reducing odorous VOC emissions from swine manure using soybean peroxidase and peroxides

    Science.gov (United States)

    Air emissions from swine production facilities can cause odor nuisance issues. Peroxidase enzymes have been used to treat phenolic compounds in industrial wastewaters, but little is known about their efficacy for treating swine manure. The objective of the research was to determine the optimum app...

  20. Global dataset of biogenic VOC emissions calculated by the MEGAN model over the last 30 years

    Directory of Open Access Journals (Sweden)

    K. Sindelarova

    2014-04-01

    Full Text Available The Model of Emissions of Gases and Aerosols from Nature (MEGANv2.1 together with the Modern-Era Retrospective Analysis for Research and Applications (MERRA meteorological fields were used to create a global emission dataset of biogenic volatile organic compounds (BVOC available on a monthly basis for the time period of 1980–2010. This dataset is called MEGAN-MACC. The model estimated mean annual total BVOC emission of 760 Tg (C yr−1 consisting of isoprene (70%, monoterpenes (11%, methanol (6%, acetone (3%, sesquiterpenes (2.5% and other BVOC species each contributing less than 2%. Several sensitivity model runs were performed to study the impact of different model input and model settings on isoprene estimates and resulted in differences of up to ±17% of the reference isoprene total. A greater impact was observed for a sensitivity run applying parameterization of soil moisture deficit that led to a 50% reduction of isoprene emissions on a global scale, most significantly in specific regions of Africa, South America and Australia. MEGAN-MACC estimates are comparable to results of previous studies. More detailed comparison with other isoprene inventories indicated significant spatial and temporal differences between the datasets especially for Australia, Southeast Asia and South America. MEGAN-MACC estimates of isoprene, α-pinene and group of monoterpenes showed a reasonable agreement with surface flux measurements at sites located in tropical forests in the Amazon and Malaysia. The model was able to capture the seasonal variation of isoprene emissions in the Amazon forest.

  1. Evaluations of NOx and highly reactive VOC emission inventories in Texas and their implications for ozone plume simulations during the Texas Air Quality Study 2006

    Science.gov (United States)

    Kim, S.-W.; McKeen, S. A.; Frost, G. J.; Lee, S.-H.; Trainer, M.; Richter, A.; Angevine, W. M.; Atlas, E.; Bianco, L.; Boersma, K. F.; Brioude, J.; Burrows, J. P.; de Gouw, J.; Fried, A.; Gleason, J.; Hilboll, A.; Mellqvist, J.; Peischl, J.; Richter, D.; Rivera, C.; Ryerson, T.; Te Lintel Hekkert, S.; Walega, J.; Warneke, C.; Weibring, P.; Williams, E.

    2011-11-01

    Satellite and aircraft observations made during the 2006 Texas Air Quality Study (TexAQS) detected strong urban, industrial and power plant plumes in Texas. We simulated these plumes using the Weather Research and Forecasting-Chemistry (WRF-Chem) model with input from the US EPA's 2005 National Emission Inventory (NEI-2005), in order to evaluate emissions of nitrogen oxides (NOx = NO + NO2) and volatile organic compounds (VOCs) in the cities of Houston and Dallas-Fort Worth. We compared the model results with satellite retrievals of tropospheric nitrogen dioxide (NO2) columns and airborne in-situ observations of several trace gases including NOx and a number of VOCs. The model and satellite NO2 columns agree well for regions with large power plants and for urban areas that are dominated by mobile sources, such as Dallas. However, in Houston, where significant mobile, industrial, and in-port marine vessel sources contribute to NOx emissions, the model NO2 columns are approximately 50%-70% higher than the satellite columns. Similar conclusions are drawn from comparisons of the model results with the TexAQS 2006 aircraft observations in Dallas and Houston. For Dallas plumes, the model-simulated NO2 showed good agreement with the aircraft observations. In contrast, the model-simulated NO2 is ~60% higher than the aircraft observations in the Houston plumes. Further analysis indicates that the NEI-2005 NOx emissions over the Houston Ship Channel area are overestimated while the urban Houston NOx emissions are reasonably represented. The comparisons of model and aircraft observations confirm that highly reactive VOC emissions originating from industrial sources in Houston are underestimated in NEI-2005. The update of VOC emissions based on Solar Occultation Flux measurements during the field campaign leads to improved model simulations of ethylene, propylene, and formaldehyde. Reducing NOx emissions in the Houston Ship Channel and increasing highly reactive VOC emissions

  2. Evaluations of NOx and highly reactive VOC emission inventories in Texas and their implications for ozone plume simulations during the Texas Air Quality Study 2006

    Directory of Open Access Journals (Sweden)

    T. Ryerson

    2011-11-01

    Full Text Available Satellite and aircraft observations made during the 2006 Texas Air Quality Study (TexAQS detected strong urban, industrial and power plant plumes in Texas. We simulated these plumes using the Weather Research and Forecasting-Chemistry (WRF-Chem model with input from the US EPA's 2005 National Emission Inventory (NEI-2005, in order to evaluate emissions of nitrogen oxides (NOx = NO + NO2 and volatile organic compounds (VOCs in the cities of Houston and Dallas-Fort Worth. We compared the model results with satellite retrievals of tropospheric nitrogen dioxide (NO2 columns and airborne in-situ observations of several trace gases including NOx and a number of VOCs. The model and satellite NO2 columns agree well for regions with large power plants and for urban areas that are dominated by mobile sources, such as Dallas. However, in Houston, where significant mobile, industrial, and in-port marine vessel sources contribute to NOx emissions, the model NO2 columns are approximately 50%–70% higher than the satellite columns. Similar conclusions are drawn from comparisons of the model results with the TexAQS 2006 aircraft observations in Dallas and Houston. For Dallas plumes, the model-simulated NO2 showed good agreement with the aircraft observations. In contrast, the model-simulated NO2 is ~60% higher than the aircraft observations in the Houston plumes. Further analysis indicates that the NEI-2005 NOx emissions over the Houston Ship Channel area are overestimated while the urban Houston NOx emissions are reasonably represented. The comparisons of model and aircraft observations confirm that highly reactive VOC emissions originating from industrial sources in Houston are underestimated in NEI-2005. The update of VOC emissions based on Solar Occultation Flux measurements during the field campaign leads to improved model simulations of ethylene, propylene, and formaldehyde. Reducing NOx emissions in the Houston Ship Channel and increasing highly

  3. Evaluations of NOx and highly reactive VOC emission inventories in Texas and their implications for ozone plume simulations during the Texas Air Quality Study 2006

    Directory of Open Access Journals (Sweden)

    T. Ryerson

    2011-07-01

    Full Text Available Satellite and aircraft observations made during the 2006 Texas Air Quality Study (TexAQS detected strong urban, industrial and power plant plumes in Texas. We simulated these plumes using the Weather Research and Forecasting – Chemistry (WRF-Chem model with input from the US EPA's 2005 National Emission Inventory (NEI-2005, in order to evaluate emissions of nitrogen oxides (NOx = NO + NO2 and volatile organic compounds (VOCs in the cities of Houston and Dallas-Fort Worth. We compared the model results with satellite retrievals of tropospheric nitrogen dioxide (NO2 columns and airborne in-situ observations of several trace gases including NOx and a number of VOCs. The model and satellite NO2 columns agree well for regions with large power plants and for urban areas that are dominated by mobile sources, such as Dallas. However, in Houston, where significant mobile, industrial, and in-port marine vessel sources contribute to NOx emissions, the model NO2 columns are approximately 50 %–70 % higher than the satellite columns. Similar conclusions are drawn from comparisons of the model results with the TexAQS 2006 aircraft observations in Dallas and Houston. For Dallas plumes, the model-simulated NO2 showed good agreement with the aircraft observations. In contrast, the model-simulated NO2 is ~60 % higher than the aircraft observations in the Houston plumes. Further analysis indicates that the NEI-2005 NOx emissions over the Houston Ship Channel area are overestimated while the urban Houston NOx emissions are reasonably represented. The comparisons of model and aircraft observations confirm that highly reactive VOC emissions originating from industrial sources in Houston are underestimated in NEI-2005. The update of VOC emissions based on Solar Occultation Flux measurements during the field campaign leads to improved model simulations of ethylene, propylene, and formaldehyde. Reducing NOx emissions in the Houston Ship Channel and increasing highly

  4. 长江三角洲地区基于喷涂工艺的溶剂源 VOCs 排放特征%Process-based Emission Characteristics of Volatile Organic Compounds(VOCs) from Paint Industry in the Yangtze River Delta, China

    Institute of Scientific and Technical Information of China (English)

    莫梓伟; 牛贺; 陆思华; 邵敏; 勾斌

    2015-01-01

    了解挥发性有机物(volatile organic compounds,VOCs)的溶剂源排放特征是制定长江三角洲地区 PM2.5和臭氧防控策略的关键.本研究通过罐采样-GC-MS/ FID 测定了长江三角洲地区重点喷涂行业(集装箱喷涂、造船喷涂、木器喷涂和汽车喷涂业)的 VOCs 排放特征.结果表明,长江三角洲地区喷涂行业排放的主要 VOCs 组分为甲苯、二甲苯、乙苯等芳香烃类物质,三者之和占总 VOCs 的质量分数为79%~99%.生产工艺的不同对 VOCs 的排放组成影响并不大,废气处理装置中活性炭吸附对 VOCs 的组成并无明显影响,而催化燃烧的处理过程会使 VOCs 的排放组成产生显著变化,乙烯排放明显增大,同时也使得催化燃烧处理最大增量反应活性(maximum increment reactivity,MIR)值高于活性炭吸附处理后的 MIR 值,说明不同的处理措施的使用将影响 VOCs 对臭氧的生成作用.%Understanding the volatile organic compounds (VOCs) emission characteristics from solvent usage industry is essential to reduce PM2. 5 and O3 in Yangtze River Delta region. In this work, VOCs source characteristics of ship container, shipbuilding, wood, and automobile painting industry were measured using canister-GC-MS/ FID analysis system. The results showed that VOCs emitted from these industrial sectors were mainly aromatics, such as toluene, xylene, and ethylbenzene, accounting for 79% - 99% of total VOCs. The VOCs treatment facilities of activated carbon adsorption had little impact on changing the composition patterns of VOCs, while catalytic combustion treatments produced more alkenes. The combustion treatment of VOCs changed the maximum increment reactivity (MIR) of the VOCs emissions, and was thus very likely to change the ozone formation potentials.

  5. Overview of VOC emissions and chemistry from PTR-TOF-MS measurements during the SusKat-ABC campaign: high acetaldehyde, isoprene and isocyanic acid in wintertime air of the Kathmandu Valley

    Science.gov (United States)

    Sarkar, Chinmoy; Sinha, Vinayak; Kumar, Vinod; Rupakheti, Maheswar; Panday, Arnico; Mahata, Khadak S.; Rupakheti, Dipesh; Kathayat, Bhogendra; Lawrence, Mark G.

    2016-03-01

    The Kathmandu Valley in Nepal suffers from severe wintertime air pollution. Volatile organic compounds (VOCs) are key constituents of air pollution, though their specific role in the valley is poorly understood due to insufficient data. During the SusKat-ABC (Sustainable Atmosphere for the Kathmandu Valley-Atmospheric Brown Clouds) field campaign conducted in Nepal in the winter of 2012-2013, a comprehensive study was carried out to characterise the chemical composition of ambient Kathmandu air, including the determination of speciated VOCs, by deploying a proton transfer reaction time-of-flight mass spectrometer (PTR-TOF-MS) - the first such deployment in South Asia. In the study, 71 ion peaks (for which measured ambient concentrations exceeded the 2σ detection limit) were detected in the PTR-TOF-MS mass scan data, highlighting the chemical complexity of ambient air in the valley. Of the 71 species, 37 were found to have campaign average concentrations greater than 200 ppt and were identified based on their spectral characteristics, ambient diel profiles and correlation with specific emission tracers as a result of the high mass resolution (m / Δm > 4200) and temporal resolution (1 min) of the PTR-TOF-MS. The concentration ranking in the average VOC mixing ratios during our wintertime deployment was acetaldehyde (8.8 ppb) > methanol (7.4 ppb) > acetone + propanal (4.2 ppb) > benzene (2.7 ppb) > toluene (1.5 ppb) > isoprene (1.1 ppb) > acetonitrile (1.1 ppb) > C8-aromatics ( ˜ 1 ppb) > furan ( ˜ 0.5 ppb) > C9-aromatics (0.4 ppb). Distinct diel profiles were observed for the nominal isobaric compounds isoprene (m / z = 69.070) and furan (m / z = 69.033). Comparison with wintertime measurements from several locations elsewhere in the world showed mixing ratios of acetaldehyde ( ˜ 9 ppb), acetonitrile ( ˜ 1 ppb) and isoprene ( ˜ 1 ppb) to be among the highest reported to date. Two "new" ambient compounds, namely formamide (m / z = 46.029) and acetamide (m / z

  6. Forest-atmosphere exchange of ozone: sensitivity to very reactive biogenic VOC emissions and implications for in-canopy photochemistry

    Directory of Open Access Journals (Sweden)

    G. M. Wolfe

    2011-08-01

    Full Text Available Understanding the fate of ozone within and above forested environments is vital to assessing the anthropogenic impact on ecosystems and air quality at the urban-rural interface. Observed forest-atmosphere exchange of ozone is often much faster than explicable by stomatal uptake alone, suggesting the presence of additional ozone sinks within the canopy. Using the Chemistry of Atmosphere-Forest Exchange (CAFE model in conjunction with summer noontime observations from the 2007 Biosphere Effects on Aerosols and Photochemistry Experiment (BEARPEX-2007, we explore the viability and implications of the hypothesis that ozonolysis of very reactive but yet unidentified biogenic volatile organic compounds (BVOC can influence the forest-atmosphere exchange of ozone. Non-stomatal processes typically generate 67 % of the observed ozone flux, but reactions of ozone with measured BVOC, including monoterpenes and sesquiterpenes, can account for only 2 % of this flux during the selected timeframe. By incorporating additional emissions and chemistry of a proxy for very reactive VOC (VRVOC that undergo rapid ozonolysis, we demonstrate that an in-canopy chemical ozone sink of ~2 × 108 molec cm−3 s−1 can close the ozone flux budget. Even in such a case, the 65 min chemical lifetime of ozone is much longer than the canopy residence time of ~2 min, highlighting that chemistry can influence reactive trace gas exchange even when it is "slow" relative to vertical mixing. This level of VRVOC ozonolysis could enhance OH and RO2 production by as much as 1 pptv s−1 and substantially alter their respective vertical profiles depending on the actual product yields. Reaction products would also contribute significantly to the oxidized VOC budget and, by extension, secondary organic aerosol mass. Given the potentially significant ramifications of a chemical ozone flux for both in-canopy chemistry and estimates of ozone

  7. Forest-atmosphere exchange of ozone: sensitivity to very reactive biogenic VOC emissions and implications for in-canopy photochemistry

    Directory of Open Access Journals (Sweden)

    G. M. Wolfe

    2011-05-01

    Full Text Available Understanding the fate of ozone within and above forested environments is vital to assessing the anthropogenic impact on ecosystems and air quality at the urban-rural interface. Observed forest-atmosphere exchange of ozone is often much faster than explicable by stomatal uptake alone, suggesting the presence of additional ozone sinks within the canopy. Using the Chemistry of Atmosphere-Forest Exchange (CAFE model in conjunction with summer noontime observations from the 2007 Biosphere Effects on Aerosols and Photochemistry Experiment (BEARPEX-2007, we explore the viability and implications of the hypothesis that ozonolysis of very reactive but yet unidentified biogenic volatile organic compounds (BVOC can influence the forest-atmosphere exchange of ozone. Non-stomatal processes typically generate 67% of the observed ozone flux, but reactions of ozone with measured BVOC, including monoterpenes and sesquiterpenes, can account for only 2% of this flux during the selected timeframe. By incorporating additional emissions and chemistry of a proxy for very reactive VOC (VRVOC that undergo rapid ozonolysis, we demonstrate that an in-canopy chemical ozone sink of ~2×108 molecules cm−3 s−1 can close the ozone flux budget. Even in such a case, the 65 min chemical lifetime of ozone is much longer than the canopy residence time of ~2 min, highlighting that chemistry can influence reactive trace gas exchange even when it is "slow" relative to vertical mixing. This level of VRVOC ozonolysis could enhance OH and RO2 production by as much as 1 pptv s−1 and substantially alter their respective vertical profiles depending on the actual product yields. Reaction products would also contribute significantly to the oxidized VOC budget and, by extension, secondary organic aerosol mass. Given the potentially significant ramifications of a chemical ozone flux for both in-canopy chemistry and estimates of ozone

  8. Volatile organic compounds (VOCs) in urban air: How chemistry affects the interpretation of positive matrix factorization (PMF) analysis

    Science.gov (United States)

    Yuan, Bin; Shao, Min; de Gouw, Joost; Parrish, David D.; Lu, Sihua; Wang, Ming; Zeng, Limin; Zhang, Qian; Song, Yu; Zhang, Jianbo; Hu, Min

    2012-12-01

    Volatile organic compounds (VOCs) were measured online at an urban site in Beijing in August-September 2010. Diurnal variations of various VOC species indicate that VOCs concentrations were influenced by photochemical removal with OH radicals for reactive species and secondary formation for oxygenated VOCs (OVOCs). A photochemical age-based parameterization method was applied to characterize VOCs chemistry. A large part of the variability in concentrations of both hydrocarbons and OVOCs was explained by this method. The determined emission ratios of hydrocarbons to acetylene agreed within a factor of two between 2005 and 2010 measurements. However, large differences were found for emission ratios of some alkanes and C8 aromatics between Beijing and northeastern United States secondary formation from anthropogenic VOCs generally contributed higher percentages to concentrations of reactive aldehydes than those of inert ketones and alcohols. Anthropogenic primary emissions accounted for the majority of ketones and alcohols concentrations. Positive matrix factorization (PMF) was also used to identify emission sources from this VOCs data set. The four resolved factors were three anthropogenic factors and a biogenic factor. However, the anthropogenic factors are attributed here to a common source at different stages of photochemical processing rather than three independent sources. Anthropogenic and biogenic sources of VOCs concentrations were not separated completely in PMF. This study indicates that photochemistry of VOCs in the atmosphere complicates the information about separated sources that can be extracted from PMF and the influence of photochemical processing must be carefully considered in the interpretation of source apportionment studies based upon PMF.

  9. The Development of a SPME-GC/MS Method for the Analysis of VOC Emissions from Historic Plastic and Rubber Materials

    OpenAIRE

    Curran, K.; Underhill, M.; Gibson, L. T.; Strlic, M.

    2015-01-01

    Analytical methods have been developed for the analysis of VOC emissions from historic plastic and rubber materials using SPME-GC/MS. Parameters such as analysis temperature, sampling time and choice of SPME fibre coating were investigated and sampling preparation strategies explored, including headspace sampling in vials and in gas sampling bags. The repeatability of the method was evaluated. It was found that a 7 d accumulation time at room temperature, followed by sampling using a DVB/CAR/...

  10. Major reactive species of ambient volatile organic compounds (VOCs) and their sources in Beijing

    Institute of Scientific and Technical Information of China (English)

    SHAO; Min; FU; Linlin; LIU; Ying; LU; Sihua; ZHANG; Yuanhan

    2005-01-01

    Volatile organic compounds (VOCs) are important precursors of atmospheric chemical processes. As a whole mixture, the ambient VOCs show very strong chemical reactivity. Based on OH radical loss rates in the air, the chemical reactivity of VOCs in Beijing was calculated. The results revealed that alkenes, accounting for only about 15% in the mixing ratio of VOCs, provide nearly 75% of the reactivity of ambient VOCs and the C4 to C5 alkenes were the major reactive species among the alkenes. The study of emission characteristics of various VOCs sources indicated that these alkenes are mainly from vehicle exhaust and gasoline evaporation. The reduction of alkene species in these two sources will be effective in photochemical pollution control in Beijing.

  11. Impacts of seasonal and regional variability in biogenic VOC emissions on surface ozone in the Pearl River Delta region, China

    Directory of Open Access Journals (Sweden)

    S. Situ

    2013-03-01

    Full Text Available In this study, the BVOC emissions in November 2010 over the Pearl River Delta (PRD region in southern China have been estimated by the latest version of a Biogenic Volatile Organic Compound (BVOC emission model (MEGAN v2.1. The evaluation of MEGAN performance at a representative forest site within this region indicates MEGAN can estimate BVOC emissions reasonably well in this region except overestimating isoprene emission in autumn for reasons that are discussed in this manuscript. Along with the output from MEGAN, the Weather Research and Forecasting model with chemistry (WRF-Chem is used to estimate the impacts of BVOC emissions on surface ozone in the PRD region. The results show BVOC emissions increase the daytime ozone peak by ~3 ppb on average, and the max hourly impacts of BVOC emissions on the daytime ozone peak is 24.8 ppb. Surface ozone mixing ratios in the central area of Guangzhou-Foshan and the western Jiangmen are most sensitive to BVOC emissions BVOCs from outside and central PRD influence the central area of Guangzhou-Foshan and the western Jiangmen significantly while BVOCs from rural PRD mainly influence the western Jiangmen. The impacts of BVOC emissions on surface ozone differ in different PRD cities, and the impact varies in different seasons. Foshan and Jiangmen being most affected in autumn, result in 6.0 ppb and 5.5 ppb increases in surface ozone concentrations, while Guangzhou and Huizhou become more affected in summer. Three additional experiments concerning the sensitivity of surface ozone to MEGAN input variables show that surface ozone is more sensitive to landcover change, followed by emission factors and meteorology.

  12. Impacts of seasonal and regional variability in biogenic VOC emissions on surface ozone in the Pearl River Delta region, China

    Energy Technology Data Exchange (ETDEWEB)

    Situ, S.; Guenther, Alex B.; Wang, X. J.; Jiang, X.; Turnipseed, A.; Wu, Z.; Bai, J.; Wang, X.

    2013-12-05

    In this study, the BVOC emissions in November 2010 over the Pearl River Delta (PRD) region in southern China have been estimated by the latest version of a Biogenic Volatile Organic Compound (BVOC) emission model (MEGAN v2.1). The evaluation of MEGAN performance at a representative forest site within this region indicates MEGAN can estimate BVOC emissions reasonably well in this region except overestimating isoprene emission in autumn for reasons that are discussed in this manuscript. Along with the output from MEGAN, the Weather Research and Forecasting model with chemistry (WRF-Chem) is used to estimate the impacts of BVOC emissions on surface ozone in the PRD region. The results show BVOC emissions increase the daytime ozone peak by *3 ppb on average, and the max hourly impacts of BVOC emissions on the daytime ozone peak is 24.8 ppb. Surface ozone mixing ratios in the central area of Guangzhou- Foshan and the western Jiangmen are most sensitive to BVOC emissions BVOCs from outside and central PRD influence the central area of Guangzhou-Foshan and the western Jiangmen significantly while BVOCs from rural PRD mainly influence the western Jiangmen. The impacts of BVOC emissions on surface ozone differ in different PRD cities, and the impact varies in different seasons. Foshan and Jiangmen being most affected in autumn, result in 6.0 ppb and 5.5 ppb increases in surface ozone concentrations, while Guangzhou and Huizhou become more affected in summer. Three additional experiments concerning the sensitivity of surface ozone to MEGAN input variables show that surface ozone is more sensitive to landcover change, followed by emission factors and meteorology.

  13. Characterization of odorous charge and photochemical reactivity of VOC emissions from a full-scale food waste treatment plant in China.

    Science.gov (United States)

    Ni, Zhe; Liu, Jianguo; Song, Mingying; Wang, Xiaowei; Ren, Lianhai; Kong, Xin

    2015-03-01

    Food waste treatment plants (FWTPs) are usually associated with odorous nuisance and health risks, which are partially caused by volatile organic compound (VOC) emissions. This study investigated the VOC emissions from a selected full-scale FWTP in China. The feedstock used in this plant was mainly collected from local restaurants. For a year, the FWTP was closely monitored on specific days in each season. Four major indoor treatment units of the plant, including the storage room, sorting/crushing room, hydrothermal hydrolysis unit, and aerobic fermentation unit, were chosen as the monitoring locations. The highest mean concentration of total VOC emissions was observed in the aerobic fermentation unit at 21,748.2-31,283.3 μg/m3, followed by the hydrothermal hydrolysis unit at 10,798.1-23,144.4 μg/m3. The detected VOC families included biogenic compounds (oxygenated compounds, hydrocarbons, terpenes, and organosulfur compounds) and abiogenic compounds (aromatic hydrocarbons and halocarbons). Oxygenated compounds, particularly alcohols, were the most abundant compounds in all samples. With the use of odor index analysis and principal components analysis, the hydrothermal hydrolysis and aerobic fermentation units were clearly distinguished from the pre-treatment units, as characterized by their higher contributions to odorous nuisance. Methanthiol was the dominant odorant in the hydrothermal hydrolysis unit, whereas aldehyde was the dominant odorant in the aerobic fermentation unit. Terpenes, specifically limonene, had the highest level of propylene equivalent concentration during the monitoring periods. This concentration can contribute to the increase in the atmospheric reactivity and ozone formation potential in the surrounding air.

  14. Stable carbon isotope ratios of ambient aromatic volatile organic compounds

    Science.gov (United States)

    Kornilova, Anna; Huang, Lin; Saccon, Marina; Rudolph, Jochen

    2016-09-01

    Measurements of mixing ratios and stable carbon isotope ratios of aromatic volatile organic compounds (VOC) in the atmosphere were made in Toronto (Canada) in 2009 and 2010. Consistent with the kinetic isotope effect for reactions of aromatic VOC with the OH radical the observed stable carbon isotope ratios are on average significantly heavier than the isotope ratios of their emissions. The change of carbon isotope ratio between emission and observation is used to determine the extent of photochemical processing (photochemical age, ∫ [OH]dt) of the different VOC. It is found that ∫ [OH]dt of different VOC depends strongly on the VOC reactivity. This demonstrates that for this set of observations the assumption of a uniform ∫ [OH]dt for VOC with different reactivity is not justified and that the observed values for ∫ [OH]dt are the result of mixing of VOC from air masses with different values for ∫ [OH]dt. Based on comparison between carbon isotope ratios and VOC concentration ratios it is also found that the varying influence of sources with different VOC emission ratios has a larger impact on VOC concentration ratios than photochemical processing. It is concluded that for this data set the use of VOC concentration ratios to determine ∫ [OH]dt would result in values for ∫ [OH]dt inconsistent with carbon isotope ratios and that the concept of a uniform ∫ [OH]dt for an air mass has to be replaced by the concept of individual values of an average ∫ [OH]dt for VOC with different reactivity.

  15. Volatile Organic Compound (VOC measurements in the Pearl River Delta (PRD region, China

    Directory of Open Access Journals (Sweden)

    Chih-chung Chang

    2008-03-01

    Full Text Available We measured levels of ambient volatile organic compounds (VOCs at seven sites in the Pearl River Delta (PRD region of China during the Air Quality Monitoring Campaign spanning 4 October to 3 November 2004. Two of the sites, Guangzhou (GZ and Xinken (XK, were intensive sites at which we collected multiple daily canister samples. The observations reported here provide a look at the VOC distribution, speciation, and photochemical implications in the PRD region. Alkanes constituted the largest percentage (>40% in mixing ratios of the quantified VOCs at six sites; the exception was one major industrial site that was dominated by aromatics (about 52%. Highly elevated VOC levels occurred at GZ during two pollution episodes; however, the chemical composition of VOCs did not exhibit noticeable changes during these episodes. We calculated the OH loss rate to estimate the chemical reactivity of all VOCs. Of the anthropogenic VOCs, alkenes played a predominant role in VOC reactivity at GZ, whereas the contributions of reactive aromatics were more important at XK. Our preliminary analysis of the VOC correlations suggests that the ambient VOCs at GZ came directly from local sources (i.e., automobiles; those at XK were influenced by both local emissions and transportation of air mass from upwind areas.

  16. Relative contribution of oxygenated hydrocarbons to the total biogenic VOC emissions of selected mid-European agricultural and natural plant species

    Science.gov (United States)

    König, Georg; Brunda, Monika; Puxbaum, Hans; Hewitt, C. Nicholas; Duckham, S. Craig; Rudolph, Jochen

    Emission rates of more than 50 individual VOCs were determined for eight plant species and three different types of grass land typical for natural deciduous and agricultural vegetation in Austria. In addition to the emissions of isoprene and monoterpenes, 33 biogenic oxygenated volatile organic compounds (BOVOCs) were detected. Of these, 2-methyl-l-propanol, 1-butanal, 2-butanal, 1-pentanol, 3-pentanol, 1-hexanol, 6-methyl-5-hepten-2-one, butanal and ethylhexylacetate were observed for the first time as plant emissions. In terms of prevalence of one of the groups of emitted VOCs (isoprene, terpenes, BOVOCs) the grain plants wheat and rye, grape, oilseed rape and the decidous trees hombeam and birch could be classified as "BOVOC"-emitters. For the grass plots examined, BOVOCs and terpenes appear to be of equal importance. The emission rates of the total assigned organic plant emissions ranged from 0.01 μ g -1 h -1 for wheat to 0.8 μg g -1 h -1 for oak (based on dry leaf weight). Intercomparison with available data from other studies show that our emission rates are rather at the lower end of reported ranges. The influence of the stage of growth was examined for rye, rape (comparing emissions of blossoming and nonblossoming plants) and for grape (with and without fruit). Emission rate differences for different stages of growth varied from nondetectable for blossoming and nonblossoming rye to a factor of six for the grape with fruits vs grape without fruits (emission rate based on dry leaf weight). The major decidous tree in Austria (beech) is a terpene emitter, with the contribution of BOVOCs below 5% of the total assigned emissions of 0.2 μg g -1 h -1 for the investigations of 20°C.

  17. From emissions to ambient mixing ratios: on-line seasonal field measurements of volatile organic compounds over a Norway spruce dominated forest in central Germany

    Science.gov (United States)

    Bourtsoukidis, E.; Williams, J.; Kesselmeier, J.; Jacobi, S.; Bonn, B.

    2013-11-01

    Biogenic volatile organic compounds (BVOC) are substantial contributors to atmospheric chemistry and physics and demonstrate the close relationship between biosphere and atmosphere. Their emission rates are highly sensitive to meteorological and environmental changes with concomitant impacts on atmospheric chemistry. We have investigated seasonal isoprenoid and oxygenated VOC (oxVOC) fluxes from a Norway spruce (Picea abies) tree in Central Germany and explored the emission responses under various atmospheric conditions. Emission rates were quantified by using dynamic branch enclosure and Proton Transfer Reaction-Mass Spectrometry (PTR-MS) techniques. Additionally, ambient mixing ratios were derived through application of a new box model treatment on the dynamic chamber measurements. These are compared in terms of abundance and origin with the corresponding emissions. Isoprenoids govern the BVOC emissions from Norway spruce, with monoterpenes and sesquiterpenes accounting for 50.8 ± 7.2% and 19.8 ± 8.1% respectively of the total emissions. Normalizing the VOC emission rates, we have observed a trend of reduction of carbon containing emissions from April to November, with an enhancement of oxVOC. Highest emission rates were observed in June for all measured species, with the exception of sesquiterpenes that were emitted most strongly in April. We exploit the wide range of conditions experienced at the site to filter the dataset with a combination of temperature, ozone and absolute humidity values in order to derive the emission potential and temperature dependency development for the major chemical species investigated. A profound reduction of monoterpene emission potential (E30) and temperature dependency (β) was found under low temperature regimes, combined with low ozone levels (E30MT, LTLO3=56 ± 9.1 ng g(dw)-1 h-1, βMT,LTLO3=0.03±0.01 K-1) while a combination of both stresses was found to alter their emissions responses with respect to temperature

  18. VOCs and OVOCs distribution and control policy implications in Pearl River Delta region, China

    Science.gov (United States)

    Louie, Peter K. K.; Ho, Josephine W. K.; Tsang, Roy C. W.; Blake, Donald R.; Lau, Alexis K. H.; Yu, Jian Zhen; Yuan, Zibing; Wang, Xinming; Shao, Min; Zhong, Liuju

    2013-09-01

    Ambient air measurements of volatile organic compounds (VOCs) and oxygenated volatile organic compounds (OVOCs) were conducted and characterised during a two-year grid study in the Pearl River Delta (PRD) region of southern China. The present grid study pioneered the systematic investigation of the nature and characteristics of complex VOC and OVOC sources at a regional scale. The largest contributing VOCs, accounting over 80% of the total VOCs mixing ratio, were toluene, ethane, ethyne, propane, ethene, butane, benzene, pentane, ethylbenzene, and xylenes. Sub-regional VOC spatial characteristics were identified, namely: i) relatively fresh pollutants, consistent with elevated vehicular and industrial activities, around the PRD estuary; and ii) a concentration gradient with higher mixing ratios of VOCs in the west as compared with the eastern part of PRD. Based on alkyl nitrate aging determination, a high hydroxyl radical (OH) concentration favoured fast hydrocarbon reactions and formation of locally produced ozone. The photochemical reactivity analysis showed aromatic hydrocarbons and alkenes together consisted of around 80% of the ozone formation potential (OFP) among the key VOCs. We also found that the OFP from OVOCs should not be neglected since their OFP contribution was more than one-third of that from VOCs alone. These findings support the choice of current air pollution control policy which focuses on vehicular sources but warrants further controls. Industrial emissions and VOCs emitted by solvents should be the next targets for ground-level ozone abatement.

  19. Measurements of VOC/SVOC emission factors from burning incenses in an environmental test chamber: influence of temperature, relative humidity, and air exchange rate.

    Science.gov (United States)

    Manoukian, A; Buiron, D; Temime-Roussel, B; Wortham, H; Quivet, E

    2016-04-01

    This study investigates the influence of three environmental indoor parameters (i.e., temperature, relative humidity, and air exchange rate) on the emission of 13 volatile organic compounds (VOCs) and semi-volatile organic compounds (SVOCs) during incense burning. Experiments have been carried out using an environmental test chamber. Statistical results from a classical two-level full factorial design highlight the predominant effect of ventilation on emission factors. The higher the ventilation, the higher the emission factor. Moreover, thanks to these results, an estimation of the concentration range for the compounds under study can be calculated and allows a quick look of indoor pollution induced by incense combustion. Carcinogenic substances (i.e., benzene, benzo(a)pyrene, and formaldehyde) produced from the incense combustion would be predicted in typical living indoors conditions to reach instantaneous concentration levels close to or higher than air quality exposure threshold values.

  20. Source Attribution of Methane Emissions in Northeastern Colorado Using Ammonia to Methane Emission Ratios

    Science.gov (United States)

    Eilerman, S. J.; Neuman, J. A.; Peischl, J.; Aikin, K. C.; Ryerson, T. B.; Perring, A. E.; Robinson, E. S.; Holloway, M.; Trainer, M.

    2015-12-01

    Due to recent advances in extraction technology, oil and natural gas extraction and processing in the Denver-Julesburg basin has increased substantially in the past decade. Northeastern Colorado is also home to over 250 concentrated animal feeding operations (CAFOs), capable of hosting over 2 million head of ruminant livestock (cattle and sheep). Because of methane's high Global Warming Potential, quantification and attribution of methane emissions from oil and gas development and agricultural activity are important for guiding greenhouse gas emission policy. However, due to the co-location of these different sources, top-down measurements of methane are often unable to attribute emissions to a specific source or sector. In this work, we evaluate the ammonia:methane emission ratio directly downwind of CAFOs using a mobile laboratory. Several CAFOs were chosen for periodic study over a 12-month period to identify diurnal and seasonal variation in the emission ratio as well as differences due to livestock type. Using this knowledge of the agricultural ammonia:methane emission ratio, aircraft measurements of ammonia and methane over oil and gas basins in the western US during the Shale Oil and Natural Gas Nexus (SONGNEX) field campaign in March and April 2015 can be used for source attribution of methane emissions.

  1. Pilot-scale testing of renewable biocatalyst for swine manure treatment and mitigation of odorous VOCs, ammonia and hydrogen sulfide emissions

    Science.gov (United States)

    Maurer, Devin L.; Koziel, Jacek A.; Bruning, Kelsey; Parker, David B.

    2017-02-01

    Comprehensive control of odors, hydrogen sulfide (H2S), ammonia (NH3), and greenhouse gas (GHG) emissions associated with swine production is a critical need. A pilot-scale experiment was conducted to evaluate surface-applied soybean peroxidase (SBP) and calcium peroxide (CaO2) as a manure additive to mitigate emissions of odorous volatile organic compounds (VOC) including dimethyl disulfide/methanethiol (DMDS/MT), dimethyl trisulfide, n-butyric acid, valeric acid, isovaleric acid, p-cresol, indole, and skatole. The secondary impact on emissions of NH3, H2S, and GHG was also measured. The SBP was tested at four treatments (2.28-45.7 kg/m2 manure) with CaO2 (4.2% by weight of SBP) over 137 days. Significant reductions in VOC emissions were observed: DMDS/MT (36.2%-84.7%), p-cresol (53.1%-89.5%), and skatole (63.2%-92.5%). There was a corresponding significant reduction in NH3 (14.6%-67.6%), and significant increases in the greenhouse gases CH4 (32.7%-232%) and CO2 (20.8%-124%). The remaining emissions (including N2O) were not statistically different. At a cost relative to 0.8% of a marketed hog it appears that SBP/CaO2 treatment could be a promising option at the lowest (2.28 kg/m2) treatment rate for reducing odorous gas and NH3 emissions at swine operations, and field-scale testing is warranted.

  2. 山西省人为源VOCs排放清单及其对臭氧生成贡献%Emission Inventory of Anthropogenic VOCs and Its Contribution to Ozone Formation in Shanxi Province

    Institute of Scientific and Technical Information of China (English)

    闫雨龙; 彭林

    2016-01-01

    Based on the activity levels, emission factors and composition characteristics of VOCs, which was obtained in statistic data and references, the emission amount of anthropogenic VOCs in Shanxi province in 2013 was calculated, and the ozone formation potential of VOCs was studied in this study. The results showed that the emission amount of anthropogenic VOCs in Shanxi province in 2013 was 723 700 t, with the major sector of the industrial emission and vehicle emission, accounting for 36. 47% and 24. 28% of total emission amount, respectively. Coke and chemicals production, the major emission source of VOCs in industrial emission, emitting 190 600 t and 38 800 t VOCs in 2013, accounting for 72. 22% and 14. 72% of industrial emission, respectively. The emission amount of ozone precursor VOCs was 435 900 t, and the total amount of ozone formation potential in Shanxi province in 2013 was 1 769 900 t. The sources of the greatest contribution to total ozone were vehicle emission, combustion sources and industrial emission. The results indicated that industrial emission was the major source of VOCs emission, which showed the simplification and heavy industrial structure. The increasing numbers of vehicles led to the huge emission of VOCs in recent years. In conclusion, the main measure of controlling the ozone pollution caused by VOCs emissions was controlling the VOCs emission from industrial emission and vehicle emission.%根据统计年年鉴中主要的人为挥发性有机物(VOCs)排放源的行业活动水平和文献中查阅到的 VOCs 排放因子和组分特征,计算了山西省2013年的人为源 VOCs 的排放量,计算了臭氧生成潜势.计算结果显示山西省2013年人为源 VOCs 排放量为72.37万 t,最主要的排放行业是工业排放源和移动源,分别占总排放量的36.47%和24.28%;在工业源中,焦炭生产和化学品生产的 VOCs 排放量分别为19.06万 t 和3.88万 t,分别占工业排放行业总排放量的72.22

  3. Diffuse emissions of Volatile Organic Compounds (VOCs) from soil in volcanic and hydrothermal systems: evidences for the influence of microbial activity on the carbon budget

    Science.gov (United States)

    Venturi, Stefania; Tassi, Franco; Fazi, Stefano; Vaselli, Orlando; Crognale, Simona; Rossetti, Simona; Cabassi, Jacopo; Capecchiacci, Francesco

    2017-04-01

    Soils in volcanic and hydrothermal areas are affected by anomalously high concentrations of gases released from the deep reservoirs, which consists of both inorganic (mainly CO2 and H2S) and organic (volatile organic compounds; VOCs) species. VOCs in volcanic and hydrothermal fluids are mainly composed of saturated and unsaturated hydrocarbons (alkanes, aromatics, alkenes, and cyclics), with variable concentrations of O- and S-bearing compounds and halocarbons, depending on the physicochemical conditions at depth. VOCs in interstitial soil gases and fumarolic emissions from four volcanic and hydrothermal systems in the Mediterranean area (Solfatara Crater, Poggio dell'Olivo and Cava dei Selci, in Italy, and Nisyros Island, in Greece) evidenced clear compositional differences, suggesting that their behavior is strongly affected by secondary processes occurring at shallow depths and likely controlled by microbial activity. Long-chain saturated hydrocarbons were significantly depleted in interstitial soil gases with respect to those from fumarolic discharges, whereas enrichments in O-bearing compounds (e.g. aldehydes, ketones), DMSO2 and cyclics were commonly observed. Benzene was recalcitrant to degradation processes, whereas methylated aromatics were relatively instable. The chemical and isotopic (δ13C in CO2 and CH4) composition of soil gases collected along vertical profiles down to 50 cm depth at both Solfatara Crater and Poggio dell'Olivo (Italy) showed evidences of relevant oxidation processes in the soil, confirming that microbial activity likely plays a major role in modifying the composition of deep-derived VOCs. Despite their harsh conditions, being typically characterized by high temperatures, low pH, and high toxic gases and metal contents, the variety of habitats characterizing volcanic and hydrothermal environments offers ideal biomes to extremophilic microbes, whose metabolic activity can consume and/or produce VOCs. In the Solfatara Crater, microbial

  4. Temporal variability and sources of VOCs in urban areas of the eastern Mediterranean

    Science.gov (United States)

    Kaltsonoudis, Christos; Kostenidou, Evangelia; Florou, Kalliopi; Psichoudaki, Magda; Pandis, Spyros N.

    2016-11-01

    During the summer of 2012 volatile organic compounds (VOCs) were monitored by proton transfer reaction mass spectrometry (PTR-MS) in urban sites, in Athens and Patras, two of the largest cities in Greece. Also, during the winter of 2013, PTR-MS measurements were conducted in the center of the city of Athens. Positive matrix factorization (PMF) was applied to the VOC measurements to gain insights about their sources. In summer most of the measured VOCs were due to biogenic and traffic emissions. Isoprene, monoterpenes, and several oxygenated VOCs (oVOCs) originated mainly from vegetation either directly or as oxidation products. Isoprene average concentrations in Patras and Athens were 1 and 0.7 ppb respectively, while the monoterpene concentrations were 0.3 and 0.9 ppb respectively. Traffic was the main source of aromatic compounds during summer. For Patras and Athens the average concentrations of benzene were 0.1 and 0.2 ppb, of toluene 0.3 and 0.8 ppb, and of the xylenes 0.3 and 0.7 ppb respectively. Winter measurements in Athens revealed that biomass burning used for residential heating was a major VOC source contributing both aromatic VOCs and biogenic compounds such as monoterpenes. Several episodes related to biomass burning were identified and emission ratios (ERs) and emission factors (EFs) were estimated.

  5. Galaxy emission line classification using 3D line ratio diagrams

    CERN Document Server

    Vogt, Frédéric P A; Kewley, Lisa J; Sutherland, Ralph S; Scharwaechter, Julia; Basurah, Hassan M; Ali, Alaa; Amer, Morsi A

    2014-01-01

    Two-dimensional (2D) line ratio diagnostic diagrams have become a key tool in understanding the excitation mechanisms of galaxies. The curves used to separate the different regions - HII-like or else excited by an active galactic nucleus (AGN) - have been refined over time but the core technique has not evolved significantly. However, the classification of galaxies based on their emission line ratios really is a multi-dimensional problem. Here we exploit recent software developments to explore the potential of three-dimensional (3D) line ratio diagnostic diagrams. We introduce a specific set of 3D diagrams, the ZQE diagrams, which separate the oxygen abundance and the ionisation parameter of HII region-like spectra, and which also enable us to probe the excitation mechanism of the gas. By examining these new 3D spaces interactively, we define a new set of 2D diagnostics, the ZE diagnostics, which can provide the metallicity of objects excited by hot young stars, and which cleanly separate HII region-like obje...

  6. The impact of biogenic VOC emissions on photochemical ozone formation during a high ozone pollution episode in the Iberian Peninsula in the 2003 summer season

    Directory of Open Access Journals (Sweden)

    N. Castell

    2008-04-01

    Full Text Available Throughout Europe the summer of 2003 was exceptionally warm, especially July and August. The European Environment Agency (EEA reported several ozone episodes, mainly in the first half of August. These episodes were exceptionally long-lasting, spatially extensive, and associated to high temperatures. In this paper, the 10$ndash;15 August 2003 ozone pollution event has been analyzed using meteorological and regional air quality modelling. During this period the threshold values of the European Directive 2002/3/EC were exceeded in various areas of the Iberian Peninsula.

    The aim of this paper is to computationally understand and quantify the influence of biogenic volatile organic compound (BVOC emissions in the formation of tropospheric ozone during this high ozone episode. Being able to differentiate how much ozone comes from biogenic emissions alone and how much comes from the interaction between anthropogenic and biogenic emissions would be helpful to develop a feasible and effective ozone control strategy. The impact on ozone formation was also studied in combination with various anthropogenic emission reduction strategies, i.e., when anthropogenic VOC emissions and/or NOx emissions are reduced. The results show a great dependency of the BVOC contribution to ozone formation on the antropoghenic reduction scenario. In rural areas, the impact due to a NOx and/or VOC reduction does not change the BVOC impact. Nevertheless, within big cities or industrial zones, a NOx reduction results in a decrease of the biogenic impact in ozone levels that can reach 85 μg/m3, whereas an Anthropogenic Volatile Organic Compound (AVOC reduction results in a decrease of the BVOC contribution on ozone formation that varies from 0 to 30 μg/m3 with respect to the contribution at the same points in the 2003 base scenario. On the other hand, downwind of the big cities, a decrease in NOx produces

  7. Biofiltration of wastewater lift station emissions: evaluation of VOC removal in the presence of H{sub 2}S

    Energy Technology Data Exchange (ETDEWEB)

    Martinez, Alvaro; Rathibandla, Snehasheela; Jones, Kim; Cabezas, Jose [Texas A and M University-Kingsville, Department of Environmental Engineering, Kingsville, TX (United States)

    2008-02-15

    The capacity of biofilter systems to remove volatile organic compounds in the presence of high concentrations of hydrogen sulfide was investigated for applications in wastewater lift stations. The treatment system was an enclosed unit composed of a biotrickling filter coupled with a biofilter. The biofilter media were plastic hollow spherical balls filled with a compost mixture; and the biotrickling filter media was a structured plastic packing. The gases from the pumping station wet well were a mixture of H{sub 2}S and low concentration aliphatic and aromatic VOCs, toluene being the most significant in concentrations of 41 ppb. The H{sub 2}S concentration was 314 ppm with fluctuations of 100 ppm resulting from pumping cycles at the station. No inhibition effect was detected from the simultaneous biological removal of VOCs and H{sub 2}S: toluene removal efficiency was 91% with the two sections contributing approximately equally to the pollutant removal; and the average removal of H{sub 2}S was 74%. A traditional open-in-ground biofilter filled with wood chips and compost, existing in the site, attained similar removal efficiencies for toluene, but the elimination capacity of the biotrickling/biofilter system was 3.3-times higher than the open biofilter. (orig.)

  8. Characterizing the chemical evolution of air masses via multi-platform measurements of volatile organic compounds (VOCs) during CalNEX: Composition, OH reactivity, and potential SOA formation

    Science.gov (United States)

    Gilman, J. B.; Kuster, W. C.; Bon, D.; Warneke, C.; Lerner, B. M.; Williams, E. J.; Holloway, J. S.; Pollack, I. B.; Ryerson, T. B.; Atlas, E. L.; Blake, D. R.; Herndon, S. C.; Zahniser, M. S.; Vlasenko, A. L.; Li, S.; Alvarez, S. L.; Rappenglueck, B.; Flynn, J. H.; Grossberg, N.; Lefer, B. L.; De Gouw, J. A.

    2011-12-01

    Volatile organic compounds (VOCs) are critical components in the photochemical production of ozone (O3) and secondary organic aerosol (SOA). During the CalNex 2010 field campaign, an extensive set of VOCs were measured at the Pasadena ground site, and aboard the NOAA WP-3D aircraft and the WHOI Research Vessel Atlantis. The measurements from each platform provide a unique perspective into the emissions, transport, and atmospheric processing of VOCs within the South Coast Air Basin (SoCAB). The observed enhancement ratios of the hydrocarbons measured on all three platforms are in good agreement and are generally well correlated with carbon monoxide (CO), indicating the prevalence of on-road VOC emission sources throughout the SoCAB. Offshore measurements aboard the ship and aircraft are used to characterize the air mass composition as a function of the land/sea-breeze effect. VOC ratios and other trace gases are used to identify air masses containing relatively fresh emissions that were often associated with offshore flow and re-circulated continental air associated with onshore flow conditions. With the prevailing southwesterly airflow pattern in the LAB throughout the daytime, the Pasadena ground site effectively functions as a receptor site and is used to characterize primary VOC emissions from downtown Los Angeles and to identify the corresponding secondary oxidation products. The chemical evolution of air masses as a function of the time of day is investigated in order to determine the relative impacts of primary emissions vs. secondary VOC products on OH reactivity and potential SOA formation. The reactivity of VOCs with the hydroxyl radical (OH) at the Pasadena site was dominated by the light hydrocarbons, isoprene, and oxygenated VOCs including aldehydes (secondary products) and alcohols (primary anthropogenic emissions). Toluene and benzaldehyde, both of which are associated with primary anthropogenic emissions, are the predominant VOC precursors to the

  9. Observations of VOC emissions and photochemical products over US oil- and gas-producing regions using high-resolution H3O+ CIMS (PTR-ToF-MS

    Directory of Open Access Journals (Sweden)

    A. Koss

    2017-08-01

    Full Text Available VOCs related to oil and gas extraction operations in the United States were measured by H3O+ chemical ionization time-of-flight mass spectrometry (H3O+ ToF-CIMS/PTR-ToF-MS from aircraft during the Shale Oil and Natural Gas Nexus (SONGNEX campaign in March–April 2015. This work presents an overview of major VOC species measured in nine oil- and gas-producing regions, and a more detailed analysis of H3O+ ToF-CIMS measurements in the Permian Basin within Texas and New Mexico. Mass spectra are dominated by small photochemically produced oxygenates and compounds typically found in crude oil: aromatics, cyclic alkanes, and alkanes. Mixing ratios of aromatics were frequently as high as those measured downwind of large urban areas. In the Permian, the H3O+ ToF-CIMS measured a number of underexplored or previously unreported species, including aromatic and cycloalkane oxidation products, nitrogen heterocycles including pyrrole (C4H5N and pyrroline (C4H7N, H2S, and a diamondoid (adamantane or unusual monoterpene. We additionally assess the specificity of a number of ion masses resulting from H3O+ ion chemistry previously reported in the literature, including several new or alternate interpretations.

  10. Observations of VOC emissions and photochemical products over US oil- and gas-producing regions using high-resolution H3O+ CIMS (PTR-ToF-MS)

    Science.gov (United States)

    Koss, Abigail; Yuan, Bin; Warneke, Carsten; Gilman, Jessica B.; Lerner, Brian M.; Veres, Patrick R.; Peischl, Jeff; Eilerman, Scott; Wild, Rob; Brown, Steven S.; Thompson, Chelsea R.; Ryerson, Thomas; Hanisco, Thomas; Wolfe, Glenn M.; St. Clair, Jason M.; Thayer, Mitchell; Keutsch, Frank N.; Murphy, Shane; de Gouw, Joost

    2017-08-01

    VOCs related to oil and gas extraction operations in the United States were measured by H3O+ chemical ionization time-of-flight mass spectrometry (H3O+ ToF-CIMS/PTR-ToF-MS) from aircraft during the Shale Oil and Natural Gas Nexus (SONGNEX) campaign in March-April 2015. This work presents an overview of major VOC species measured in nine oil- and gas-producing regions, and a more detailed analysis of H3O+ ToF-CIMS measurements in the Permian Basin within Texas and New Mexico. Mass spectra are dominated by small photochemically produced oxygenates and compounds typically found in crude oil: aromatics, cyclic alkanes, and alkanes. Mixing ratios of aromatics were frequently as high as those measured downwind of large urban areas. In the Permian, the H3O+ ToF-CIMS measured a number of underexplored or previously unreported species, including aromatic and cycloalkane oxidation products, nitrogen heterocycles including pyrrole (C4H5N) and pyrroline (C4H7N), H2S, and a diamondoid (adamantane) or unusual monoterpene. We additionally assess the specificity of a number of ion masses resulting from H3O+ ion chemistry previously reported in the literature, including several new or alternate interpretations.

  11. Detection of marine methane emissions with AVIRIS band ratios

    Science.gov (United States)

    Bradley, Eliza S.; Leifer, Ira; Roberts, Dar A.; Dennison, Philip E.; Washburn, Libe

    2011-05-01

    The relative source contributions of methane (CH4) have high uncertainty, creating a need for local-scale characterization in concert with global satellite measurements. However, efforts towards methane plume imaging have yet to provide convincing results for concentrated sources. Although atmospheric CH4 mapping did not motivate the Airborne Visible/Infrared Imaging Spectrometer (AVIRIS) design, recent studies suggest its potential for studying concentrated CH4 sources such as the Coal Oil Point (COP) seep field (˜0.015 Tg CH4 yr-1) offshore Santa Barbara, California. In this study, we developed a band ratio approach on high glint COP AVIRIS data and demonstrate the first successful local-scale remote sensing mapping of natural atmospheric CH4 plumes. Plume origins closely matched surface and sonar-derived seepage distributions, with plume characteristics consistent with wind advection. Imaging spectrometer data may also be useful for high spatial-resolution characterization of concentrated, globally-significant CH4 emissions from offshore platforms and cattle feedlots.

  12. Development and demonstration of a method to monitor the effects of measures to reduce VOC emissions in the EU. LIFE 95/NL/A11/NL/365/ZHL [1996-1998] (Final Report )

    NARCIS (Netherlands)

    Keuken, M.P.; Oss, R.F. van

    1998-01-01

    In 1996, TNO was granted by the European Commission to carry out in the framework of the LIFE programme a project entitled "Development and dem-onstration of a method to monitor the effects of measures to reduce VOC emis-sions in the EU". An additional grant was supplied by the Dutch Ministry for Ho

  13. 688 AMBIENT VOLATILE ORGANIC COMPOUNDS (VOCS ...

    African Journals Online (AJOL)

    Osondu

    The VOCs were classified thus: aromatics 41%, halogenated 42%, esters 3%, ketones 8%, ... and Industrial emission were identified as sources of VOCs in the studied industrial area with ... canisters, or by dynamic or diffusive adsorption .... The GC/FID was standardized and ... with CS2 was prepared from stock standard in.

  14. DEVELOPING A NO-VOC WOOD TOPCOAT

    Science.gov (United States)

    The paper reports an evaluation of a new low-VOC (volatile organic compound) wood coating technology, its performance characteristics, and its application and emissions testing. The low-VOC wood coating selected for the project was a two-component, water-based epoxy coating. Poly...

  15. Effect of bark beetle (Ips typographus L.) attack on bark VOC emissions of Norway spruce (Picea abies Karst.) trees

    Science.gov (United States)

    Ghimire, Rajendra P.; Kivimäenpää, Minna; Blomqvist, Minna; Holopainen, Toini; Lyytikäinen-Saarenmaa, Päivi; Holopainen, Jarmo K.

    2016-02-01

    Climate warming driven storms are evident causes for an outbreak of the European spruce bark beetle (Ips typographus L.) resulting in the serious destruction of mature Norway spruce (Picea abies Karst.) forests in northern Europe. Conifer species are major sources of biogenic volatile organic compounds (BVOCs) in the boreal zone. Climate relevant BVOC emissions are expected to increase when conifer trees defend against bark beetle attack by monoterpene (MT)-rich resin flow. In this study, BVOC emission rates from the bark surface of beetle-attacked and non-attacked spruce trees were measured from two outbreak areas, Iitti and Lahti in southern Finland, and from one control site at Kuopio in central Finland. Beetle attack increased emissions of total MTs 20-fold at Iitti compared to Kuopio, but decreased the emissions of several sesquiterpenes (SQTs) at Iitti. At the Lahti site, the emission rate of α-pinene was positively correlated with mean trap catch of bark beetles. The responsive individual MTs were tricyclene, α-pinene, camphene, myrcene, limonene, 1,8-cineole and bornyl acetate in both of the outbreak areas. Our results suggest that bark beetle outbreaks affect local BVOC emissions from conifer forests dominated by Norway spruce. Therefore, the impacts of insect outbreaks are worth of consideration to global BVOC emission models.

  16. Methanol and other VOC fluxes from a Danish beech forest during late springtime

    DEFF Research Database (Denmark)

    Schade, Gunnar W.; Solomon, Sheena J.; Dellwik, Ebba;

    2011-01-01

    In-canopy mixing ratio gradients and above-canopy fluxes of several volatile organic compounds (VOCs) were measured using a commercial proton transfer reaction mass spectrometer (PTR-MS) in a European beech (Fagus sylvatica) forest in Denmark. Fluxes of methanol were bidirectional: Emission...

  17. Volatile Organic Compounds (VOCs in Conventional and High Performance School Buildings in the U.S.

    Directory of Open Access Journals (Sweden)

    Lexuan Zhong

    2017-01-01

    Full Text Available Exposure to volatile organic compounds (VOCs has been an indoor environmental quality (IEQ concern in schools and other buildings for many years. Newer designs, construction practices and building materials for “green” buildings and the use of “environmentally friendly” products have the promise of lowering chemical exposure. This study examines VOCs and IEQ parameters in 144 classrooms in 37 conventional and high performance elementary schools in the U.S. with the objectives of providing a comprehensive analysis and updating the literature. Tested schools were built or renovated in the past 15 years, and included comparable numbers of conventional, Energy Star, and Leadership in Energy and Environmental Design (LEED-certified buildings. Indoor and outdoor VOC samples were collected and analyzed by thermal desorption, gas chromatography and mass spectroscopy for 94 compounds. Aromatics, alkanes and terpenes were the major compound groups detected. Most VOCs had mean concentrations below 5 µg/m3, and most indoor/outdoor concentration ratios ranged from one to 10. For 16 VOCs, the within-school variance of concentrations exceeded that between schools and, overall, no major differences in VOC concentrations were found between conventional and high performance buildings. While VOC concentrations have declined from levels measured in earlier decades, opportunities remain to improve indoor air quality (IAQ by limiting emissions from building-related sources and by increasing ventilation rates.

  18. Volatile Organic Compounds (VOCs) in Conventional and High Performance School Buildings in the U.S.

    Science.gov (United States)

    Zhong, Lexuan; Su, Feng-Chiao; Batterman, Stuart

    2017-01-01

    Exposure to volatile organic compounds (VOCs) has been an indoor environmental quality (IEQ) concern in schools and other buildings for many years. Newer designs, construction practices and building materials for “green” buildings and the use of “environmentally friendly” products have the promise of lowering chemical exposure. This study examines VOCs and IEQ parameters in 144 classrooms in 37 conventional and high performance elementary schools in the U.S. with the objectives of providing a comprehensive analysis and updating the literature. Tested schools were built or renovated in the past 15 years, and included comparable numbers of conventional, Energy Star, and Leadership in Energy and Environmental Design (LEED)-certified buildings. Indoor and outdoor VOC samples were collected and analyzed by thermal desorption, gas chromatography and mass spectroscopy for 94 compounds. Aromatics, alkanes and terpenes were the major compound groups detected. Most VOCs had mean concentrations below 5 µg/m3, and most indoor/outdoor concentration ratios ranged from one to 10. For 16 VOCs, the within-school variance of concentrations exceeded that between schools and, overall, no major differences in VOC concentrations were found between conventional and high performance buildings. While VOC concentrations have declined from levels measured in earlier decades, opportunities remain to improve indoor air quality (IAQ) by limiting emissions from building-related sources and by increasing ventilation rates. PMID:28117727

  19. EVALUATION OF LOW-VOC LATEX PAINTS

    Science.gov (United States)

    The paper gives results of an evaluation of four commercially available low-VOC (volatile organic compound) latex paints as substitutes for conventional latex paints by assessing both their emission characteristics and their performance as coatings. Bulk analysis indicated that ...

  20. VOC signatures from North American oil and gas sources (Invited)

    Science.gov (United States)

    Simpson, I. J.; Marrero, J.; Blake, N. J.; Barletta, B.; Hartt, G.; Meinardi, S.; Schroeder, J.; Apel, E. C.; Hornbrook, R. S.; Blake, D. R.

    2013-12-01

    Between 2008 and 2013 UC Irvine has used its whole air sampling (WAS) technique to investigate VOC source signatures from a range of oil and gas sources in North America, including five separate field campaigns at the Alberta oil sands (1 airborne, 4 ground-based); the 2010 Deepwater Horizon oil spill (airborne and ship-based); the 2012 airborne Deep Convective Clouds and Chemistry Project (DC3) mission over oil and gas wells in Colorado, Texas and Oklahoma; and the 2013 ground-based Barnett Shale Campaign in Texas. Each campaign has characterized more than 80 individual C1-C10 VOCs including alkanes, alkenes and aromatics. For example, oil sands are an extra-heavy, unconventional crude oil that is blended with diluent in order to flow, and upgraded into synthetic crude oil. The VOC signature at the oil sands mining and upgrading facilities is alkane-rich, and the fuel gas associated with these operations has an i-butane/n-butane ratio similar to that of liquefied petroleum gas (LPG). In addition to light alkanes, enhanced levels of benzene were observed over US oil and natural gas wells during DC3, likely because of its use in hydrofracking fluid. A series of VOC emission ratios from North American petrochemical sources will be presented and compared, including oil sands, conventional oil and hydrofracking operations.

  1. A Three Year Study on 14 VOCs at One Site in Rome: Levels, Seasonal Variations, Indoor/Outdoor Ratio and Temporal Trends

    Directory of Open Access Journals (Sweden)

    Sergio Fuselli

    2010-10-01

    Full Text Available Fourteen volatile organic compounds (VOCs—twelve hydrocarbons and two organochlorine compounds—were monitored both outdoors and indoors for three years at one site in Rome. Results showed that 118 out of 168 indoor seasonal mean values were higher than the corresponding outdoor concentrations. The most relevant source of outdoor hydrocarbons was automotive exhaust emissions. Due to the enforcement of various measures to protect health and the environment, outdoor levels of monoaromatic hydrocarbons decreased about ten fold over 15 years, and aliphatic hydrocarbons also decreased. With the decrease in these outdoor concentrations, indoor air sources are likely to be more relevant for indoor air exposures. Winter outdoor values for monoaromatic hydrocarbons were generally markedly higher than the summer ones. The gradual replacement of the current fleet of circulating cars with new cars complying with EURO 5 standards, further reducing hydrocarbon emissions, may possibly lead to an increase in the observed indoor/outdoor ratios. It is indeed more difficult to remove indoor sources, some of which are still unknown.

  2. Simulated changes in biogenic VOC emissions and ozone formation from habitat expansion of Acer Rubrum (red maple)

    Science.gov (United States)

    Drewniak, Beth A.; Snyder, Peter K.; Steiner, Allison L.; Twine, Tracy E.; Wuebbles, Donald J.

    2014-01-01

    A new vegetation trend is emerging in northeastern forests of the United States, characterized by an expansion of red maple at the expense of oak. This has changed emissions of biogenic volatile organic compounds (BVOCs), primarily isoprene and monoterpenes. Oaks strongly emit isoprene while red maple emits a negligible amount. This species shift may impact nearby urban centers because the interaction of isoprene with anthropogenic nitrogen oxides can lead to tropospheric ozone formation and monoterpenes can lead to the formation of particulate matter. In this study the Global Biosphere Emissions and Interactions System was used to estimate the spatial changes in BVOC emission fluxes resulting from a shift in forest composition between oak and maple. A 70% reduction in isoprene emissions occurred when oak was replaced with maple. Ozone simulations with a chemical box model at two rural and two urban sites showed modest reductions in ozone concentrations of up to 5-6 ppb resulting from a transition from oak to red maple, thus suggesting that the observed change in forest composition may benefit urban air quality. This study illustrates the importance of monitoring and representing changes in forest composition and the impacts to human health indirectly through changes in BVOCs.

  3. Compost spreading in Mediterranean shrubland indirectly increases biogenic emissions by promoting growth of VOC-emitting plant parts

    Science.gov (United States)

    Olivier, Romain; Lavoir, Anne-Violette; Ormeño, Elena; Mouillot, Florent; Greff, Stéphane; Lecareux, Caroline; Staudt, Michael; Fernandez, Catherine

    2011-07-01

    We investigated the effect of sewage sludge compost spreading on plant growth and leaf terpene emissions and content of Quercus coccifera, Rosmarinus officinalis and Cistus albidus in a Mediterranean shrubland. Measurements were performed during 3 consecutive summers on 2 different plots treated in 2002 or 2007 with 50 or 100 tons of compost per hectare, corresponding to observations carried out 2 months to 7 years after spreading. A slight nutrient enrichment of soil and leaves ( R. officinalis and C. albidus) was observed, especially for phosphorous. Terpene emissions were not affected by compost spreading, although they tended to increase on treated plots after 6 and 7 years for R. officinalis and C. albidus respectively. Terpene content was not affected by any compost treatment. Leaf and stem growth were significantly enhanced by compost spreading after 2 and/or 7 years in all species with little difference between doses. Total leaf biomass on the last growth units was increased by more than 50% in C. albidus and more than 90% in Q. coccifera. The results suggest that compost spreading in Meditteranean shrublands has no or little direct effect on leaf terpene emissions, but indirectly leads to their increase through leaf biomass enhancement. Simulation of terpene emissions at stand level revealed an increase of terpene fluxes ranging between 6 and 13%, depending on the plant species. Overall, compost spreading was assessed to result in an emission rate of 1.1 kg ha -1 y -1 for a typical Q. coccifera shrubland, but can reach 2.6 kg ha -1 y -1 for a typical R. officinalis shrubland.

  4. VOC emission control by circulating fluidized bed adsorption; Controle de l'emission de composes organiques volatils par adsorption en lit fluidise circulant

    Energy Technology Data Exchange (ETDEWEB)

    Song, W.

    2003-12-15

    This work deals with the circulating fluidized bed technology, applied to the elimination by adsorption of volatile organic compounds (VOCs), like toluene, in a gas flow. In the process, the adsorbent (millimetric spherical grains of micro-porous carbon) is moved by a strong flow rate of gas inside a vertical tube without lining. Mass and heat transfers are very important and important volumes of compounds can be processed. This work presents the determination of the adsorption equilibrium, the description of the experimental facility and of the results of experiments, the development of an original model of the process which combines a flow model and a mass transfer model, a parametric study of this model, and finally, some extensions of the process principle to staged operations with pressure variation or temperature variation cycles. (J.S.)

  5. Source apportionment of ambient volatile organic compounds (VOCs)and their characteristics in Chengdu, southwest of China

    Science.gov (United States)

    Deng, Yuanyuan; Xie, Shaodong; Li, Jing; Li, Yaqi

    2017-04-01

    Chengdu, located in the largest basin region in the world, suffers from increasing ground-level ozone and aerosol pollutions. Volatile organic compounds (VOCs) are one of the prominent precursors of ground-level ozone and aerosols. Ambient VOCs were measured continuously using an online gas chromatography-mass spectrometry/flame ionization detector (GC-MS/FID) with a time resolution of 1 hour from 28 August 2016 to 7 October 2016 at Pixian in Chengdu. 99 measurements of VOCs were conducted including 28 alkanes, 11 alkenes, 16 aromatics, 13 oxygenated VOCs (OVOCs) and 29 halocarbons, acetylene, and acetonitrile. Based on the hourly average data, positive matrix factorization (PMF) was used to better understand the emission sources of VOCs in Chengdu. The average mixing ratios of alkanes, alkenes, aromatics, OVOCs, halocarbons, acetylene, and acetonitrile were respectively 14.49 ppbv, 4.92 ppbv, 5.14 ppbv, 9.74 ppbv, 7.77 ppbv, 3.56 ppbv, and 0.43 ppbv. Six sources were extracted by using PMF model. Liquefied petroleum gas, background and petrochemical industries contributed 28%, 19%, 18% to the total ambient VOCs, respectively. Biogenic emission (14%), Gasoline vehicles (13%), Solvent use (8%) were also identified as major sources of ambient VOCs at Pixian.

  6. Biomonitoring of VOC emissions from the coating process at DaimlerChrysler - an inside view of motivation factors

    Energy Technology Data Exchange (ETDEWEB)

    Hahn, H.U. [DaimlerChrysler AG, Sindelfingen (Germany); Kostka-Rick, R. [Biologisch Ueberwachen und Bewerten, Echterdingen (Germany)

    2002-07-01

    To reduce ambient air pollution by solvents in the Boeblingen/Sindelfingen area, water-based paints were introduced in the Sindelfingen factory in the early nineties. Effect monitoring using plants was to clarify what effects the coating process had on the environment and to what extent the environmental impact was reduced by water-based paint technology. Depending on the results, the new method was to be optimized. In terms of the environmental liability legislation, the findings were to permit a self-appraisal of production effects. Between 1992 and 1996, a special bio-indication process tailored to the solvent emissions from the paint shop was developed. From 37 different plant species and varieties, nasturtium, different varieties of bush bean and of tomato were selected as bio-indicators, reacting specifically and sensitively to the solvent emissions. The monitoring plants were exposed at 13 different sites on the factory premises and in the urban area of Sindelfingen for air quality monitoring. Since 1992, more than 9,700 plants have been exposed and investigated and some 125,000 injury scores have been recorded. (orig.)

  7. Securing and reporting for 2008 and 2010 on the amount and type of VOC emissions from plants in the scope of the 31th BImSchV; Sicherung und Berichterstattung fuer 2008 und 2010 ueber Menge und Art der VOC-Emissionen aus Anlagen im Geltungsbereich der 31.BImSchV

    Energy Technology Data Exchange (ETDEWEB)

    Tebert, Christian; Volz, Susanne [Institut fuer Oekologie und Politik GmbH (OEKOPOL), Hamburg (Germany); Theloke, Jochen [Stuttgart Univ. (DE). Inst. fuer Energiewirtschaft und Rationelle Energieanwendung (IER)

    2011-09-15

    The Directive 1999/13/EC (also called ''VOC-directive'' or ''Solvents Directive'') obliges the Member States of the European Union to a preparation of a report on the implementation of this Directive every three years. The target of a project of the Federal Environment Agency (Dessau-Rosslau, Federal Republic of Germany) is to assist the federal government in meeting the reporting requirements and to relieve the Federal States during data acquisition as possible. For this, an estimation of the CMR material types and quantities of CMR is focused. Recommendations are pronounced to determine the total emissions of VOCs from plants within the scope of the 31th BImSchV (Federal Nuisance Control Ordinance). The research project investigated the requirements for data provision in the individual Federal States and the possibilities for data delivery in addition to a full survey of the Federal States.

  8. Modeling the uncertainty of several VOC and its impact on simulated VOC and ozone in Houston, Texas

    Science.gov (United States)

    Pan, Shuai; Choi, Yunsoo; Roy, Anirban; Li, Xiangshang; Jeon, Wonbae; Souri, Amir Hossein

    2015-11-01

    A WRF-SMOKE-CMAQ modeling system was used to study Volatile Organic Compound (VOC) emissions and their impact on surface VOC and ozone concentrations in southeast Texas during September 2013. The model was evaluated against the ground-level Automated Gas Chromatograph (Auto-GC) measurement data from the Texas Commission on Environmental Quality (TCEQ). The comparisons indicated that the model over-predicted benzene, ethylene, toluene and xylene, while under-predicting isoprene and ethane. The mean biases between simulated and observed values of each VOC species showed clear daytime, nighttime, weekday and weekend variations. Adjusting the VOC emissions using simulated/observed ratios improved model performance of each VOC species, especially mitigating the mean bias substantially. Simulated monthly mean ozone showed a minor change: a 0.4 ppb or 1.2% increase; while a change of more than 5 ppb was seen in hourly ozone data on high ozone days, this change moved model predictions closer to observations. The CMAQ model run with the adjusted emissions better reproduced the variability in the National Aeronautics and Space Administration (NASA)'s Ozone Monitoring Instrument (OMI) formaldehyde (HCHO) columns. The adjusted model scenario also slightly better reproduced the aircraft HCHO concentrations from NASA's DISCOVER-AQ campaign conducted during the simulation episode period; Correlation, Mean Bias and RMSE improved from 0.34, 1.38 ppb and 2.15 ppb to 0.38, 1.33 ppb and 2.08 ppb respectively. A process analysis conducted for both industrial/urban and rural areas suggested that chemistry was the main process contributing to ozone production in both areas, while the impact of chemistry was smaller in rural areas than in industrial and urban areas. For both areas, the positive chemistry contribution increased in the sensitivity simulation largely due to the increase in emissions. Nudging VOC emissions to match the observed concentrations shifted the ozone hotspots

  9. Odor and VOC Emissions from Pan Frying of Mackerel at Three Stages: Raw, Well-Done, and Charred

    Directory of Open Access Journals (Sweden)

    Jeong-Hyeon Ahn

    2014-11-01

    Full Text Available Many classes of odorants and volatile organic compounds that are deleterious to our wellbeing can be emitted from diverse cooking activities. Once emitted, they can persist in our living space for varying durations. In this study, various volatile organic compounds released prior to and during the pan frying of fish (mackerel were analyzed at three different cooking stages (stage 1 = raw (R, stage 2 = well-done (W, and stage 3 = overcooked/charred (O. Generally, most volatile organic compounds recorded their highest concentration levels at stage 3 (O, e.g., 465 (trimethylamine and 106 ppb (acetic acid. In contrast, at stage 2 (W, the lowest volatile organic compounds emissions were observed. The overall results of this study confirm that trimethylamine is identified as the strongest odorous compound, especially prior to cooking (stage 1 (R and during overcooking leading to charring (stage 3 (O. As there is a paucity of research effort to measure odor intensities from pan frying of mackerel, this study will provide valuable information regarding the management of indoor air quality.

  10. On-road measurements of vehicle NO2/NOx emission ratios in Denver, Colorado, USA

    Science.gov (United States)

    Wild, Robert J.; Dubé, William P.; Aikin, Kenneth C.; Eilerman, Scott J.; Neuman, J. Andrew; Peischl, Jeff; Ryerson, Thomas B.; Brown, Steven S.

    2017-01-01

    Nitrogen oxides (NOx = NO + NO2) emitted by on-road combustion engines are important contributors to tropospheric ozone production. The NOx fraction emitted as nitrogen dioxide (NO2) is usually presumed to be small but can affect ozone production and distribution, and this fraction is generally not reported in emissions inventories. We have developed an accurate method for determination of this primary NO2 emission and demonstrated it during measurement of on-road vehicle emission plumes from a mobile laboratory during July and August 2014 in the region between Denver and Greeley in Colorado. During a total of approximately 90 h of sampling from an instrumented mobile laboratory, we identified 1867 vehicle emission plumes, which were extracted using an algorithm that looks for rapid and large increases in measured NOx. We find a distribution of NO2/NOx emissions similar to a log-normal profile, with an average emission ratio of 0.053 ± 0.002 per sampled NOx plume. The average is not weighted by the total NOx emissions from sampled vehicles, which is not measured here, and so may not represent the NO2/NOx ratio of the total NOx emission if this ratio is a function of NOx itself. Although our current data set does not distinguish between different engine types (e.g., gasoline, light duty diesel and heavy duty diesel), the ratio is on the low end of recent reports of vehicle fleet NO2 to NOx emission ratios in Europe.

  11. Locating industrial VOC sources with aircraft observations.

    Science.gov (United States)

    Toscano, P; Gioli, B; Dugheri, S; Salvini, A; Matese, A; Bonacchi, A; Zaldei, A; Cupelli, V; Miglietta, F

    2011-05-01

    Observation and characterization of environmental pollution, focussing on Volatile Organic Compounds (VOCs), in a high-risk industrial area, are particularly important in order to provide indications on a safe level of exposure, indicate eventual priorities and advise on policy interventions. The aim of this study is to use the Solid Phase Micro Extraction (SPME) method to measure VOCs, directly coupled with atmospheric measurements taken on a small aircraft environmental platform, to evaluate and locate the presence of VOC emission sources in the Marghera industrial area. Lab analysis of collected SPME fibres and subsequent analysis of mass spectrum and chromatograms in Scan Mode allowed the detection of a wide range of VOCs. The combination of this information during the monitoring campaign allowed a model (Gaussian Plume) to be implemented that estimates the localization of emission sources on the ground.

  12. Catalytic oxidation of volatile organic compounds (VOCs) - A review

    Science.gov (United States)

    Kamal, Muhammad Shahzad; Razzak, Shaikh A.; Hossain, Mohammad M.

    2016-09-01

    Emission of volatile organic compounds (VOCs) is one of the major contributors to air pollution. The main sources of VOCs are petroleum refineries, fuel combustions, chemical industries, decomposition in the biosphere and biomass, pharmaceutical plants, automobile industries, textile manufacturers, solvents processes, cleaning products, printing presses, insulating materials, office supplies, printers etc. The most common VOCs are halogenated compounds, aldehydes, alcohols, ketones, aromatic compounds, and ethers. High concentrations of these VOCs can cause irritations, nausea, dizziness, and headaches. Some VOCs are also carcinogenic for both humans and animals. Therefore, it is crucial to minimize the emission of VOCs. Among the available technologies, the catalytic oxidation of VOCs is the most popular because of its versatility of handling a range of organic emissions under mild operating conditions. Due to that fact, there are numerous research initiatives focused on developing advanced technologies for the catalytic destruction of VOCs. This review discusses recent developments in catalytic systems for the destruction of VOCs. Review also describes various VOCs and their sources of emission, mechanisms of catalytic destruction, the causes of catalyst deactivation, and catalyst regeneration methods.

  13. MEMS acoustic emission transducers designed with high aspect ratio geometry

    Science.gov (United States)

    Saboonchi, H.; Ozevin, D.

    2013-09-01

    In this paper, micro-electro-mechanic systems (MEMS) acoustic emission (AE) transducers are manufactured using an electroplating technique. The transducers use a capacitance change as their transduction principle, and are tuned to the range 50-200 kHz. Through the electroplating technique, a thick metal layer (20 μm nickel + 0.5 μm gold) is used to form a freely moving microstructure layer. The presence of the gold layer reduces the potential corrosion of the nickel layer. A dielectric layer is deposited between the two electrodes, thus preventing the stiction phenomenon. The transducers have a measured quality factor in the range 15-30 at atmospheric pressure and are functional without vacuum packaging. The transducers are characterized using electrical and mechanical tests to identify the capacitance, resonance frequency and damping. Ultrasonic wave generation using a Q-switched laser shows the directivity of the transducer sensitivity. The comparison of the MEMS transducers with similar frequency piezoelectric transducers shows that the MEMS AE transducers have better response characteristics and sensitivity at the resonance frequency and well-defined waveform signatures (rise time and decay time) due to pure resonance behavior in the out-of-plane direction. The transducers are sensitive to a unique wave direction, which can be utilized to increase the accuracy of source localization by selecting the correct wave velocity at the structures.

  14. Emission control measures for precursors of tropospheric ozone. Pt. 1 and 2; Emissionsminderungsmoeglichkeiten bei Vorlaeufersubstanzen von bodennahem Ozon. Bd. 1: Systemanalyse der Ozonminderungsmassnahmen in den USA. Bd. 2: Luftreinhaltemassnahmen in den USA zur Minderung von VOC-Emissionen aus Kleinanlagen und Produkten und Vergleich mit europaeischen Regelungen

    Energy Technology Data Exchange (ETDEWEB)

    Leclaire, T.; Schiefer, C.; Bergmann, S.; Hrabovski, Z. [Institut fuer Umwelttechnologie und Umweltanalytik e.V. (IUTA), Duisburg (Germany)

    1998-08-01

    For more than two decades now experiences of ozone reduction have been made in the USA. In many regions great efforts for VOC control are made to reduce their high ozone concentrations in ambient air that in some cases reach up to more than twice the German peak concentrations. This report places focus on small stationary sources and products, for these sources actually contribute more than half of the VOC emissions in Germany and are still not regulated under the German Immission Control Law. Therefore, main aim of this examination was to determine the major elements of VOC control strategies in the U.S. and to consider, whether strategies and measures are transferable taking into account German circumstances. Volume 1 describes the strategies and measures for ozone control in the U.S. (national) as well as in five regions with high ozone concentrations in ambient air. The authorities and responsbilities at federal, state, regional, and local levels are highlighted, legislation and different types of regulations are explained, priorities concerning VOC versus NO{sub x} related control are mentioned and the control measures on different sources for reducing VOC and NO{sub x} are summarized briefly. Volume 2 contains a detailed description of control measures for reducing VOC emissions from products and stationary sources, namely the proposed national VOC emission standards for coatings and consumer products, the California Consumer Products Regulations, the state-wide requirements for industrial and commercial sources in California and the VOC related rules of the South Coast Air Quality Management District (LA and surrounded Countries). The South Coast Rules were chosen as an example for District Rules for they were generally the most stringent because of the extreme ozone concentration in this area. Moreover, the regulations for VOC emission control in Europe concerning small stationary sources and products are mentioned. The different approaches to control VOC

  15. New method for simulation of VOC emission from building materials and measurement of mass transfer parameters%建材VOC散发过程模拟与传质参数测定新方法

    Institute of Scientific and Technical Information of China (English)

    宋伟; 孔庆媛; 李洪枚

    2013-01-01

    建材中挥发性有机化合物(VOC)的散发是一个复杂传质过程.为准确把握传质特性,首先建立了一套描述干建材散发行为的显性完全解析模型,适用于模拟对人体最不利的无换气情况;代入有关文献中的传质参数预测了环境舱浓度,与文献中对应的实验数据及数值算法预测值吻合良好.然后基于对模型的分析提出一套简便快捷的实验方法,能够利用不同VOC背景值下干建材在密闭舱中散发的平衡浓度或逐时浓度,求取预测散发过程的4个重要的传质参数:可散发浓度C0、扩散系数D、分配系数K和对流传质系数hm;实验部分测算了两类密度板中甲醛散发的C0、D、K、hm,代入数值算法预测了密闭舱和直流舱的环境舱浓度,与实验数据吻合良好.该套模型和测定方法能够应用于建材散发的模拟研究.%Emission of volatile organic compounds (VOC) from building materials is a complex process of mass transfer. To have a clear picture of mass transfer characteristics, this paper first established an explicitly fully analytical model describing VOC emission behavior from dry building materials, which is applicable to emission simulation in static chamber that is most unfavorable to human health. The VOC concentration in the chamber predicted based on the mass transfer parameters in literature is in good agreement with corresponding experimental data and numerical calculation in literature. Based on this model, an experimental method is proposed for convenient, rapid and simultaneous measurement of four important mass transfer parameters for VOC emission prediction (emittable concentration C0, diffusion coefficient D, partition coefficient K and convection mass transfer coefficient hm) by making use of emission equilibrium or process concentration in a static chamber at a series of background concentrations. With the values of C0, D, K and hm for formaldehyde emission mass transfer obtained

  16. POCP for individual VOC under European conditions

    Energy Technology Data Exchange (ETDEWEB)

    Altenstedt, J.; Pleijel, K.

    1998-09-01

    Ground level ozone has been recognised as one of the most important environmental threats on the regional scale in Europe. Ozone is today considered to be harmful to human health already at the relatively low concentrations present in southern Scandinavia. The fact that ozone has the potential to damage vegetation at these concentrations is already well known. Ozone also gives rise to degradation of materials and is one of the gases which adds to the greenhouse effect. Ground level ozone is formed from nitrogen oxides (NO{sub x}) and volatile organic compounds (VOC) in the presence of sunlight. The only way to reduce ozone is therefore to reduce the emissions of the precursors. Ranking individual VOC by their ozone formation potential can make emission reductions more environmentally efficient and save time and money. POCP values give a ranking of the ozone formation ability of an individual VOC relative to other VOC. A critical analysis of the POCP concept has been performed which shows that the background emissions of NO{sub x} and VOC affect the POCP values to a large extent. Based on the critical analysis, five scenarios with different background emissions of NO{sub x} and VOC were selected for calculation of POCP values. These scenarios were chosen because they reflect the variation in POCP values which arise in different environments within Europe. The range thus indicates POCP values which are intended to be applicable within Europe. POCP values for 83 different VOC are presented in the form of ranges in this report. 42 refs, 13 figs, 3 tabs

  17. BAT AGN Spectroscopic Survey - III. An observed link between AGN Eddington ratio and narrow-emission-line ratios

    Science.gov (United States)

    Oh, Kyuseok; Schawinski, Kevin; Koss, Michael; Trakhtenbrot, Benny; Lamperti, Isabella; Ricci, Claudio; Mushotzky, Richard; Veilleux, Sylvain; Berney, Simon; Crenshaw, D. Michael; Gehrels, Neil; Harrison, Fiona; Masetti, Nicola; Soto, Kurt T.; Stern, Daniel; Treister, Ezequiel; Ueda, Yoshihiro

    2017-01-01

    We investigate the observed relationship between black hole mass (MBH), bolometric luminosity (Lbol) and Eddington ratio (λEdd) with optical emission-line ratios ([N II] λ6583/Hα, [S II] λλ6716, 6731/Hα, [O I] λ6300/Hα, [O III] λ5007/Hβ, [Ne III] λ3869/Hβ and He II λ4686/Hβ) of hard X-ray-selected active galactic nuclei (AGN) from the BAT AGN Spectroscopic Survey. We show that the [N II] λ6583/Hα ratio exhibits a significant correlation with λEdd (RPear = -0.44, p-value = 3 × 10-13, σ = 0.28 dex), and the correlation is not solely driven by MBH or Lbol. The observed correlation between [N II] λ6583/Hα ratio and MBH is stronger than the correlation with Lbol, but both are weaker than the λEdd correlation. This implies that the large-scale narrow lines of AGN host galaxies carry information about the accretion state of the AGN central engine. We propose that [N II] λ6583/Hα is a useful indicator of Eddington ratio with 0.6 dex of rms scatter, and that it can be used to measure λEdd and thus MBH from the measured Lbol, even for high-redshift obscured AGN. We briefly discuss possible physical mechanisms behind this correlation, such as the mass-metallicity relation, X-ray heating, and radiatively driven outflows.

  18. Emission rate estimates determined for a large number of volatile organic compounds using airborne measurements for the oil sands facilities in Alberta, Canada

    Science.gov (United States)

    Li, S. M.; Leithead, A.; Moussa, S.; Liggio, J.; Moran, M. D.; Wang, D. K.; Hayden, K. L.; Darlington, A.; Gordon, M.; Staebler, R. M.; Makar, P.; Stroud, C.; McLaren, R.; Liu, P.; O'brien, J.; Mittermeier, R. L.; Zhang, J.; Marson, G.; Cober, S.; Wolde, M.; Wentzell, J.

    2016-12-01

    In August and September of 2013, aircraft-based measurements of air pollutants were made during a field campaign in support of the Joint Canada-Alberta Implementation Plan on Oil Sands Monitoring in Alberta, Canada. Volatile organic compounds (VOCs) were determined using a high resolution proton-transfer-reaction time-of-flight mass spectrometer (PTR-ToF-MS) continuously at 2-5 second resolution during the flights, and from 680 discretely sampled stainless steel canisters collected during flights followed by offline GC-MS and GC-FID analyses for four large oil sands surface mining facilities. The Top-down Emission Rate Retrieval Algorithm (TERRA), developed at Environment and Climate Change Canada (ECCC), was applied to the aromatics and oxygenated VOC results from the PTR-ToF-MS to determine their emission rates. Additional VOC species, determined in the canisters, were compared with the PTR-ToF-MS VOC species to determine their emission ratios. Using these emission ratios and the emission rates for the aromatics and oxygenated VOCs, the individual emission rates for 73-90 volatile organic compounds (VOCs) were determined for each of the four major oil sands facilities. The results are the first independently determined emission rates for a large number of VOCs at the same time for large industrial complexes such as the oil sands mining facilities. These measurement-based emission data will be important for strengthening VOC emission reporting.

  19. Emission control measures for precursors of tropospheric ozone. Pt. 1 and 2; Emissionsminderungsmoeglichkeiten bei Vorlaeufersubstanzen von bodennahem Ozon. Bd. 1: Systemanalyse der Ozonminderungsmassnahmen in den USA. Bd. 2: Luftreinhaltemassnahmen in den USA zur Minderung von VOC-Emissionen aus Kleinanlagen und Produkten und Vergleich mit europaeischen Regelungen

    Energy Technology Data Exchange (ETDEWEB)

    Leclaire, T.; Schiefer, C.; Bergmann, S.; Hrabovski, Z. [Institut fuer Umwelttechnologie und Umweltanalytik e.V. (IUTA), Duisburg (Germany)

    1998-08-01

    For more than two decades now experiences of ozone reduction have been made in the USA. In many regions great efforts for VOC control are made to reduce their high ozone concentrations in ambient air that in some cases reach up to more than twice the German peak concentrations. This report places focus on small stationary sources and products, for these sources actually contribute more than half of the VOC emissions in Germany and are still not regulated under the German Immission Control Law. Therefore, main aim of this examination was to determine the major elements of VOC control strategies in the U.S. and to consider, whether strategies and measures are transferable taking into account German circumstances. Volume 1 describes the strategies and measures for ozone control in the U.S. (national) as well as in five regions with high ozone concentrations in ambient air. The authorities and responsbilities at federal, state, regional, and local levels are highlighted, legislation and different types of regulations are explained, priorities concerning VOC versus NO{sub x} related control are mentioned and the control measures on different sources for reducing VOC and NO{sub x} are summarized briefly. Volume 2 contains a detailed description of control measures for reducing VOC emissions from products and stationary sources, namely the proposed national VOC emission standards for coatings and consumer products, the California Consumer Products Regulations, the state-wide requirements for industrial and commercial sources in California and the VOC related rules of the South Coast Air Quality Management District (LA and surrounded Countries). The South Coast Rules were chosen as an example for District Rules for they were generally the most stringent because of the extreme ozone concentration in this area. Moreover, the regulations for VOC emission control in Europe concerning small stationary sources and products are mentioned. The different approaches to control VOC

  20. Optimal strategies for VOC emission abatement produced by solvent evaporation. The Italian case study; Strategie ottimali per la riduzione delle emissioni di composti organici volatili da uso di solventi: il caso italiano

    Energy Technology Data Exchange (ETDEWEB)

    Vetrella, G.; Cirillo, M.C. [ENEA, Centro Ricerche Casaccia, Rome (Italy). Dipt. Ambiente

    1998-07-01

    This work analyses technologies and costs of VOC (volatile organic compounds) abatement in the activities which belong to the solvent evaporation sector, and then it singles out the most successful strategies from the costs point of view to reduce the sector emissions on the base of fixed abatement objectives. The Italian case is discussed. [Italian] Il lavoro analizza tecnologie e costi di abbattimento dei COV (composti organici volatili) nel settore evaporazione solventi, e individua la strategia piu' efficace dal punto di vista dei costi per ridurre le emissioni del settore sulla base di prefissati obiettivi di abbattimento. Analizza la situazione italiana.

  1. Locating industrial VOC sources with aircraft observations

    Energy Technology Data Exchange (ETDEWEB)

    Toscano, P., E-mail: p.toscano@ibimet.cnr.it [Institute for Biometeorology (IBIMET - CNR), Via G. Caproni 8, 50145 Firenze (Italy); Gioli, B. [Institute for Biometeorology (IBIMET - CNR), Via G. Caproni 8, 50145 Firenze (Italy); Dugheri, S. [Careggi Hospital-University of Florence, Occupational Health Division, Largo Palagi 1, 50100 Florence (Italy); Salvini, A. [Department of Organic Chemistry, University of Florence, Via della Lastruccia 13, 50019 Sesto Fiorentino, Florence (Italy); Matese, A. [Institute for Biometeorology (IBIMET - CNR), Via G. Caproni 8, 50145 Firenze (Italy); Bonacchi, A. [Careggi Hospital-University of Florence, Occupational Health Division, Largo Palagi 1, 50100 Florence (Italy); Zaldei, A. [Institute for Biometeorology (IBIMET - CNR), Via G. Caproni 8, 50145 Firenze (Italy); Cupelli, V. [Careggi Hospital-University of Florence, Occupational Health Division, Largo Palagi 1, 50100 Florence (Italy); Miglietta, F. [Institute for Biometeorology (IBIMET - CNR), Via G. Caproni 8, 50145 Firenze (Italy); Fondazione Edmund Mach, Via Mach 1, San Michele all' Adige, Trento (Italy)

    2011-05-15

    Observation and characterization of environmental pollution, focussing on Volatile Organic Compounds (VOCs), in a high-risk industrial area, are particularly important in order to provide indications on a safe level of exposure, indicate eventual priorities and advise on policy interventions. The aim of this study is to use the Solid Phase Micro Extraction (SPME) method to measure VOCs, directly coupled with atmospheric measurements taken on a small aircraft environmental platform, to evaluate and locate the presence of VOC emission sources in the Marghera industrial area. Lab analysis of collected SPME fibres and subsequent analysis of mass spectrum and chromatograms in Scan Mode allowed the detection of a wide range of VOCs. The combination of this information during the monitoring campaign allowed a model (Gaussian Plume) to be implemented that estimates the localization of emission sources on the ground. - Highlights: > Flight plan aimed at sampling industrial area at various altitudes and locations. > SPME sampling strategy was based on plume detection by means of CO{sub 2}. > Concentrations obtained were lower than the limit values or below the detection limit. > Scan mode highlighted presence of {gamma}-butyrolactone (GBL) compound. > Gaussian dispersion modelling was used to estimate GBL source location and strength. - An integrated strategy based on atmospheric aircraft observations and dispersion modelling was developed, aimed at estimating spatial location and strength of VOC point source emissions in industrial areas.

  2. Improvement of health risk factors after reduction of VOC concentrations in industrial and urban areas.

    Science.gov (United States)

    Lerner, Jorge Esteban Colman; Kohajda, Tibor; Aguilar, Myriam Elisabeth; Massolo, Laura Andrea; Sánchez, Erica Yanina; Porta, Atilio Andrés; Opitz, Philipp; Wichmann, Gunnar; Herbarth, Olf; Mueller, Andrea

    2014-01-01

    After reductions of fugitive and diffuse emissions by an industrial complex, a follow-up study was performed to determine the time variability of volatile organic compounds (VOCs) and the lifetime cancer risk (LCR). Passive samplers (3 M monitors) were placed outdoors (n = 179) and indoors (n = 75) in industrial, urban, and control areas for 4 weeks. Twenty-five compounds including n-alkanes, cycloalkanes, aromatics, chlorinated hydrocarbons, and terpenes were determined by GC/MS. The results show a significant decrease of all VOCs, especially in the industrial area and to a lesser extent in the urban area. The median outdoor concentration of benzene in the industrial area declined compared to the former study, around 85% and about 50% in the urban area, which in the past was strongly influenced by industrial emissions. Other carcinogenic compounds like styrene and tetrachloroethylene were reduced to approximately 60%. VOC concentrations in control areas remained nearly unchanged. According to the determined BTEX ratios and interspecies correlations, in contrast to the previous study, traffic was identified as the main emission source in the urban and control areas and showed an increased influence in the industrial area. The LCR, calculated for benzene, styrene, and tetrachloroethylene, shows a decrease of one order of magnitude in accordance to the decreased total VOC concentrations and is now acceptable according to values proposed by the World Health Organization.

  3. BAT AGN Spectroscopic Survey-III. An observed link between AGN Eddington ratio and narrow emission line ratios

    CERN Document Server

    Oh, Kyuseok; Koss, Michael; Trakhtenbrot, Benny; Lamperti, Isabella; Ricci, Claudio; Mushotzky, Richard; Veilleux, Sylvain; Berney, Simon; Crenshaw, D Michael; Gehrels, Neil; Harrison, Fiona; Masetti, Nicola; Soto, Kurt T; Stern, Daniel; Treister, Ezequiel; Ueda, Yoshihiro

    2016-01-01

    We investigate the observed relationship between black hole mass ($M_{\\rm BH}$), bolometric luminosity ($L_{\\rm bol}$), and Eddington ratio (${\\lambda}_{\\rm Edd}$) with optical emission line ratios ([NII] {\\lambda}6583/H{\\alpha}, [SII] {\\lambda}{\\lambda}6716,6731/H{\\alpha}, [OI] {\\lambda}6300/H{\\alpha}, [OIII] {\\lambda}5007/H{\\beta}, [NeIII] {\\lambda}3869/H{\\beta}, and HeII {\\lambda}4686/H{\\beta}) of hard X-ray-selected AGN from the BAT AGN Spectroscopic Survey (BASS). We show that the [NII] {\\lambda}6583/H{\\alpha} ratio exhibits a significant correlation with ${\\lambda}_{\\rm Edd}$ ($R_{\\rm Pear}$ = -0.44, $p$-value=$3\\times10^{-13}$, {\\sigma} = 0.28 dex), and the correlation is not solely driven by $M_{\\rm BH}$ or $L_{\\rm bol}$. The observed correlation between [NII] {\\lambda}6583/H{\\alpha} ratio and $M_{\\rm BH}$ is stronger than the correlation with $L_{\\rm bol}$, but both are weaker than the ${\\lambda}_{\\rm Edd}$ correlation. This implies that the large-scale narrow lines of AGN host galaxies carry informa...

  4. Ratio of the Core to the Extended Emissions in the Comoving Frame for Blazars

    Indian Academy of Sciences (India)

    Yun-Tian Li; Shao-Yu Fu; Huan-Jian Feng; Si-Le He; Chao Lin; Jun-Hui Fan; Denise Costantin; Yu-Tao Zhang

    2017-06-01

    In a two-component jet model, the emissions are the sum of the core and extended emissions: $S^{\\mathrm{ob}}=S_{\\mathrm{core}}^{\\mathrm{ob}}+S_{\\mathrm{ext}}^{\\mathrm{ob}}$, with the core emissions, $S_{\\mathrm{core}}^{\\mathrm{ob}}= f S_{\\mathrm{ext}}^{\\mathrm{ob}}\\delta ^{q}$ being a function of the Doppler factor $\\delta$, the extended emission $S_{\\mathrm{ext}}^{\\mathrm{ob}}$, the jet type dependent factor q, and the ratio of the core to the extended emissions in the comoving frame, f. The f is an unobservable but important parameter. Following our previous work, we collect 65 blazars with available Doppler factor $\\delta$, superluminal velocity $\\beta _{\\mathrm{app}}$, and core-dominance parameter, R, and calculated the ratio, f, and performed statistical analyses. We found that the ratio, f, in BL Lacs is on average larger than that in FSRQs. We suggest that the difference of the ratio f between FSRQs and BL Lacs is one of the possible reasons that cause the difference of other observed properties between them. We also find some significant correlations between $\\log f$ and other parameters, including intrinsic (de-beamed) peak frequency, $\\log \

  5. Characteristics and Source Apportionment of Volatile Organic Compounds (VOCs) in the Northern Suburb of Nanjing%南京北郊大气 VOCs 变化特征及来源解析

    Institute of Scientific and Technical Information of China (English)

    安俊琳; 朱彬; 王红磊; 杨辉

    2014-01-01

    Based on the data of volatile organic compounds (VOCs) collected continuously from 1st Mar, 2011 to 29th Feb, 2012 in the northern suburb of Nanjing, characteristics of their variability, differences of ratios of tracers and source apportionment by principal component analysis/ absolute principal component scores (PCA/ APCS) were analyzed. The results showed that the total VOCs mixing ratios were 43. 52 × 10 - 9 , which accounted for 45. 1% of alkanes, alkenes for 25. 3% , alkyne for 7. 3% , and aromatics for 22. 3% . There was an obviously seasonal variation of VOCs, with the maximum in summer and the minimum in winter. There was an obvious seasonal variation of VOCs component, with highest alkanes in winter, highest alkenes in summer, highest aromatic in spring, and highest alkyne in winter. By using the specific pollutant ratios ( hydrocarbons/ acetylene and toluene/ benzene) method, it indicated that the observation site was greatly affected by the surrounding industrial areas. Source analysis of VOCs by PCA/ APCS mode showed that the sources consisted of industrial production sources, automobile emission sources, combustion sources, industrial production volatilization sources, solvent use sources and biogenic emission sources. In addition, there were seasonal variations. Overall, the sources related to industrial production activities represented 45% - 63% of VOCs, and they were followed by automobile emission sources, which represented 34% -50% .%利用2011-03-01~2012-02-29南京北郊大气 VOCs 观测资料,对大气 VOCs 浓度变化特征和特征物比值差异展开研究,并应用 PCA/ APCS 受体模型对不同季节 VOCs 来源进行了解析.结果表明,南京大气总 VOCs 体积混合比为43.52×10-9,其中烷烃占45.1%、烯烃占25.3%、炔烃占7.3%和芳香烃占22.3%.总 VOCs 体积混合比呈现夏季高,冬季低的季节变化. VOCs 组分中烷烃在冬季最高,烯烃夏季最高,芳香烃春季最高,炔烃冬季最高.特征物比值(VOCs

  6. Covering the different steps of the coffee processing: Can headspace VOC emissions be exploited to successfully distinguish between Arabica and Robusta?

    Science.gov (United States)

    Colzi, Ilaria; Taiti, Cosimo; Marone, Elettra; Magnelli, Susanna; Gonnelli, Cristina; Mancuso, Stefano

    2017-12-15

    This work was performed to evaluate the possible application of PTR-ToF-MS technique in distinguishing between Coffea arabica (Arabica) and Coffea canephora var. robusta (Robusta) commercial stocks in each step of the processing chain (green beans, roasted beans, ground coffee, brews). volatile organic compounds (VOC) spectra from coffee samples of 7 Arabica and 6 Robusta commercial stocks were recorded and submitted to multivariate statistical analysis. Results clearly showed that, in each stage of the coffee processing, the volatile composition of coffee is highly influenced by the species. Actually, with the exception of green beans, PTR-ToF-MS technique was able to correctly recognize Arabica and Robusta samples. Particularly, among 134 tentatively identified VOCs, some masses (16 for roasted coffee, 12 for ground coffee and 12 for brewed coffee) were found to significantly discriminate the two species. Therefore, headspace VOC analyses was showed to represent a valuable tool to distinguish between Arabica and Robusta. Copyright © 2017 Elsevier Ltd. All rights reserved.

  7. Quantitative Estimate of Unorganized Emission of VOCs from Petroleum Refinery Wastwater Treatment%石化炼油废水处理VOCs无组织排放定量估算研究

    Institute of Scientific and Technical Information of China (English)

    戴晓波; 邱贤锋; 何金平; 王文成; 陈选文

    2012-01-01

    炼油厂废水处理中无组织排放VOCs是石化企业污染源核查的重要内容。概述了影响VOCs挥发因素,利用基于MATLAB神经网络工具箱的图形用户界面GUI,并且使用在某石化企业所收集的相关数据,建立了石化企业炼油废水处理中无组织排放VOCs的定量模型。通过实验,证明了模型具有更广泛的应用范围,弥补了新建项目环境影响评价中的缺陷。%In view of the fact that unorganized emission of VOSc from Wastwater Treatment is one of the major pollution sources of a petroleum refinery, this paper studies effecting factors of VOCs volatilization and establishes a quantitative model of unorganized VOCs emission from Wastewater Treatment on the basis of the data from a petroleum refinery by means of GUI of MATLAB neural network toolbox. Experiments prove that the model fits for a wide range of applications, which will im- prove project environment impact assessments.

  8. The extended narrow line region of NGC 4151. I. Emission line ratios and their implications

    OpenAIRE

    Penston, M. V.; Robinson, A.; Alloin, D.; Appenzeller, I.; Aretxaga, I.; Axon, D.J.; Baribaud, T.; Barthel, P.; Baum, S. A.; Boisson, C.; de Bruyn, A. G.; Clavel, J.; Colina, L.; Dennefeld, M.; Angeles I. Díaz

    1990-01-01

    This is an electronic version of an article published in Astronomy and Astrophysics. Penston, M.V. et al. The extended narrow line region of NGC 4151. I. Emission line ratios and their implications. Astronomy and Astrophysics 236 (1990): 53-62

  9. VOC methods and levels in Spain

    Energy Technology Data Exchange (ETDEWEB)

    Bomboi, M.T. [Area de Contaminacion Atmosferica, Instituto de Salud Carlos III, Majadahonda (Spain)

    2004-07-01

    Ozone precursors began to be studied in the eighties in Spain, in order to know their levels and composition in areas, which had high concentrations of other atmospheric polluting agents. At the end of the eighties, VOC were incorporated into the air quality networks in urban areas in order to anticipate at the derived amendments of the entrance into force on the Directive 92/72/CEE of 1992 on air pollution by ozone. At the same time, field campaigns for VOC toxics were started in specific industrial areas and the zones with high traffic. More recently, the air quality networks have been orientated to non-urban areas, to cover the knowledge of VOC in semi-urban and rural areas. On the other hand, the role of the biogenic emissions and the role that their chemical and photochemical products play in atmospheric chemistry was becoming important in the nineties. Therefore some research projects, e.g. 'Biogenic Emissions in the Mediterranean Area (BEMA)', were developed in order to understand the vegetation emissions in the Mediterranean area in relation to anthropogenic compounds and to get information on their participation in tropospheric ozone formation. VOC have been sampled at European Monitoring and Evaluation Programme (EMEP) sites since 1999, based on recommendations from the EMEP Workshop on Measurements of Hydrocarbons/VOC in Lindau 1989. Collection of light hydrocarbons started in 1999, whereas measurements of carbonyls have just started in 2003. In this work, the most important sampling and analysis techniques to determine ozone precursors and to control VOC are shown, as well as the main results obtained in projects, networks and measurement campaigns performed with these methods.

  10. Theoretical quasar emission-line ratios. VII - Energy-balance models for finite hydrogen slabs

    Science.gov (United States)

    Hubbard, E. N.; Puetter, R. C.

    1985-01-01

    The present energy balance calculations for finite, isobaric, hydrogen-slab quasar emission line clouds incorporate probabilistic radiative transfer (RT) in all lines and bound-free continua of a five-level continuum model hydrogen atom. Attention is given to the line ratios, line formation regions, level populations and model applicability results obtained. H lines and a variety of other considerations suggest the possibility of emission line cloud densities in excess of 10 to the 10th/cu cm. Lyman-beta/Lyman-alpha line ratios that are in agreement with observed values are obtained by the models. The observed Lyman/Balmer ratios can be achieved with clouds whose column depths are about 10 to the 22nd/sq cm.

  11. Diurnal and seasonal variability of gasoline-related volatile organic compound emissions in Riverside, California.

    Science.gov (United States)

    Gentner, Drew R; Harley, Robert A; Miller, Angela M; Goldstein, Allen H

    2009-06-15

    On- and off-road mobile sources are the dominant contributors to urban anthropogenic volatile organic compound (AVOC) emissions. Analyses of gasoline samples from California for both summer and winter indicate significant differences in liquid fuel and vapor chemical composition due to intentional seasonal adjustments. Ambient concentrations of 55 VOCs were measured via in situ gas chromatography in the 2005 Study of Organic Aerosols at Riverside (SOAR) during both summer and fall. A chemical mass balance analysis was used to differentiate vapor pressure-driven VOC emissions from other motor vehicle-related emissions such as tailpipe exhaust. Overall, fuel vapor emissions accounted for 31 +/- 2% of gasoline-related VOC in Riverside; California's emission factor model similarly estimates 31% of gasoline-related VOC emissions are fuel vapor. The diurnal pattern of vapor pressure-driven VOC source contributions is relatively stable around 10 microg/m3, while whole gasoline (i.e., tailpipe) contributions peak at approximately 60 microg/m3 during the morning commute. There is no peak in whole gasoline source contributions during the afternoon, due to rapid dilution associated with high mixing heights and wind speeds in the Riverside area. The relationship between estimated gasoline-related VOC and observed carbon monoxide concentrations in this study is similar to California's 2005 emission inventory; we calculated a VOC to CO mass ratio of 0.086 +/- 0.006 (95% CI) compared to 0.097 in the emission inventory for all gasoline-related sources.

  12. Volatile organic compounds (VOCs) in air from Nisyros Island (Dodecanese Archipelago, Greece): Natural versus anthropogenic sources.

    Science.gov (United States)

    Tassi, F; Capecchiacci, F; Giannini, L; Vougioukalakis, G E; Vaselli, O

    2013-09-01

    This study presents the chemical composition of VOCs in air and gas discharges collected at Nisyros Island (Dodecanese Archipelago, Greece). The main goals are i) to discriminate between natural and anthropogenic VOC sources and ii) to evaluate their impact on local air quality. Up to 63 different VOCs were recognized and quantitatively determined in 6 fumaroles and 19 air samples collected in the Lakki caldera, where fumarolic emissions are located, and the outer ring of the island, including the Mandraki village and the main harbor. Air samples from the crater area show significant concentrations of alkanes, alkenes, cyclic, aromatics, and S- and O-bearing heterocycles directly deriving from the hydrothermal system, as well as secondary O-bearing compounds from oxidation of primary VOCs. At Mandraki village, C6H6/Σ(methylated aromatics) and Σ(linear)/Σ(branched) alkanes ratios <1 allow to distinguish an anthropogenic source related to emissions from outlet pipes of touristic and private boats and buses.

  13. The Tropical Forest and Fire Emissions Experiment: method evaluation of volatile organic compound emissions measured by PTR-MS, FTIR, and GC from tropical biomass burning

    Directory of Open Access Journals (Sweden)

    T. G. Karl

    2007-11-01

    Full Text Available Volatile Organic Compound (VOC emissions from fires in tropical forest fuels were quantified using Proton-Transfer-Reaction Mass Spectrometry (PTRMS, Fourier Transform Infrared Spectroscopy (FTIR and gas chromatography (GC coupled to PTRMS (GC-PTR-MS. We investigated VOC emissions from 19 controlled laboratory fires at the USFS (United States Forest Service Fire Sciences Laboratory and 16 fires during an intensive airborne field campaign during the peak of the burning season in Brazil in 2004. The VOC emissions were dominated by oxygenated VOCs (OVOC (OVOC/NMHC ~4:1, NMHC: non-methane hydrocarbons The specificity of the PTR-MS instrument, which measures the mass to charge ratio of VOCs ionized by H3O+ ions, was validated by gas chromatography and by intercomparing in-situ measurements with those obtained from an open path FTIR instrument. Emission ratios for methyl vinyl ketone, methacrolein, crotonaldehyde, acrylonitrile and pyrrole were measured in the field for the first time. Our measurements show a higher contribution of OVOCs than previously assumed for modeling purposes. Comparison of fresh (<15 min and aged (>1 h–1 d smoke suggests altered emission ratios due to gas phase chemistry for acetone but not for acetaldehyde and methanol. Emission ratios for numerous, important, reactive VOCs with respect to acetonitrile (a biomass burning tracer are presented.

  14. Silica deactivation of bead VOC catalysts

    Energy Technology Data Exchange (ETDEWEB)

    Libanati, C.; Pereira, C.J. [Research Division, W. R. Grace and Co., Columbia, MD (United States); Ullenius, D.A. [Grace TEC Systems, De Pere, WI (United States)

    1998-01-15

    Catalytic oxidation is a key technology for controlling the emissions of Volatile Organic Compounds (VOCs) from industrial plants. The present paper examines the deactivation by silica of bead VOC catalysts in a flexographic printing application. Post mortem analyses of field-aged catalysts suggest that organosilicon compounds contained in the printing ink diffuse into the catalyst and deposit as silica particles in the micropores. Laboratory activity evaluation of aged catalysts suggests that silica deposition is non-selective and that silica masks the noble metal active site

  15. Exposure to volatile organic compounds (VOC) in public buses of Pamplona, Northern Spain.

    Science.gov (United States)

    Parra, M A; Elustondo, D; Bermejo, R; Santamaría, J M

    2008-10-01

    This study examines the exposure level of passengers and drivers to VOC in public buses in a medium-size metropolitan area (Northern Spain). In-vehicle monitoring was performed on different routes, on peak and non-peak hours, during January and February 2007. A total of 112 air samples were collected onto adsorbent tubes and analysed by thermal desorption (TD) and gas chromatography/mass selective detector (GC/MSD) technique. Statistical differences were found among route to route concentrations, with those routes with major prevalence in the commercial area of the city displaying higher values; differences between peak and non-peak hours were also observed. A decrease in VOC concentrations was also registered during the weekend. BTEX ratios were estimated and found to be related to traffic emissions and similar for all the surveyed routes. Correlations confirmed traffic as the main emission source for BTEX and trimethylbenzene, their concentrations being highly associated to changes in meteorological conditions.

  16. The Impact of Diffuse Ionized Gas on Emission-line Ratios and Gas Metallicity Measurements

    Science.gov (United States)

    Zhang, Kai; Yan, Renbin; MaNGA Team

    2016-01-01

    Diffuse Ionized Gas (DIG) is prevalent in star-forming galaxies. Using a sample of galaxies observed by MaNGA, we demonstrate how DIG in star-forming galaxies impact the measurements of emission line ratios, hence the gas-phase metallicity measurements and the interpretation of diagnostic diagrams. We demonstrate that emission line surface brightness (SB) is a reasonably good proxy to separate HII regions from regions dominated by diffuse ionized gas. For spatially-adjacent regions or regions at the same radius, many line ratios change systematically with emission line surface brightness, reflecting a gradual increase of dominance by DIG towards low SB. DIG could significantly bias the measurement of gas metallicity and metallicity gradient. Because DIG tend to have a higher temperature than HII regions, at fixed metallicity DIG displays lower [NII]/[OII] ratios. DIG also show lower [OIII]/[OII] ratios than HII regions, due to extended partially-ionized regions that enhance all low-ionization lines ([NII], [SII], [OII], [OI]). The contamination by DIG is responsible for a substantial portion of the scatter in metallicity measurements. At different surface brightness, line ratios and line ratio gradients can differ systematically. As DIG fraction could change with radius, it can affect the metallicity gradient measurements in systematic ways. The three commonly used strong-line metallicity indicators, R23, [NII]/[OII], O3N2, are all affected in different ways. To make robust metallicity gradient measurements, one has to properly isolate HII regions and correct for DIG contamination. In line ratio diagnostic diagrams, contamination by DIG moves HII regions towards composite or LINER-like regions.

  17. Relating urban airborne particle concentrations to shipping using carbon based elemental emission ratios

    Science.gov (United States)

    Johnson, Graham R.; Juwono, Alamsyah M.; Friend, Adrian J.; Cheung, Hing-Cho; Stelcer, Eduard; Cohen, David; Ayoko, Godwin A.; Morawska, Lidia

    2014-10-01

    This study demonstrates a novel method for testing the hypothesis that variations in primary and secondary particle number concentration (PNC) in urban air are related to residual fuel oil combustion at a coastal port lying 30 km upwind, by examining the correlation between PNC and airborne particle composition signatures chosen for their sensitivity to the elemental contaminants present in residual fuel oil. Residual fuel oil combustion indicators were chosen by comparing the sensitivity of a range of concentration ratios to airborne emissions originating from the port. The most responsive were combinations of vanadium and sulphur concentration ([S], [V]) expressed as ratios with respect to black carbon concentration ([BC]). These correlated significantly with ship activity at the port and with the fraction of time during which the wind blew from the port. The average [V] when the wind was predominantly from the port was 0.52 ng m-3 (87%) higher than the average for all wind directions and 0.83 ng m-3 (280%) higher than that for the lowest vanadium yielding wind direction considered to approximate the natural background. Shipping was found to be the main source of V impacting urban air quality in Brisbane. However, contrary to the stated hypothesis, increases in PNC related measures did not correlate with ship emission indicators or ship traffic. Hence at this site ship emissions were not found to be a major contributor to PNC compared to other fossil fuel combustion sources such as road traffic, airport and refinery emissions.

  18. [VOCs tax policy on China's economy development].

    Science.gov (United States)

    Liu, Chang-Xin; Wang, Yu-Fei; Wang, Hai-Lin; Hao, Zheng-Ping; Wang, Zheng

    2011-12-01

    In this paper, environmental tax was designed to control volatile organic compounds (VOCs) emissions. Computable general equilibrium (CGE) model was used to explore the impacts of environmental tax (in forms of indirect tax) on the macro-economy development at both national and sector levels. Different levels of tax were simulated to find out the proper tax rate. It is found out that imposing environmental tax on high emission sectors can cause the emission decreased immediately and can lead to negative impacts on macro-economy indicators, such as GDP (gross domestic products), total investment, total product and the whole consumption etc. However, only the government income increased. In addition, the higher the tax rate is, the more pollutants can be reduced and the worse economic effects can be caused. Consequently, it is suggested that, the main controlling policies of VOCs abatement should be mandatory orders, and low environmental tax can be implemented as a supplementary.

  19. Line Emission from Radiation-Pressurized HII Regions I: Internal Structure and Line Ratios

    CERN Document Server

    Yeh, Sherry C C; Krumholz, Mark R; Matzner, Christopher D; Tielens, Alexander G G M

    2013-01-01

    The emission line ratios [OIII]5007/H-beta and [NII]6584/H-alpha have been adopted as an empirical way to distinguish between the fundamentally different mechanisms of ionization in emission-line galaxies. However, detailed interpretation of these diagnostics requires calculations of the internal structure of the emitting HII regions, and these calculations depend on the assumptions one makes about the relative importance of radiation pressure and stellar winds. In this paper we construct a grid of quasi-static HII region models to explore how choices about these parameters alter HII regions' emission line ratios. We find that, when radiation pressure is included in our models, HII regions reach a saturation point beyond which further increases in the luminosity of the driving stars does not produce any further increase in effective ionization parameter, and thus does not yield any further alteration in an HII region's line ratio. We also show that, if stellar winds are assumed to be strong, the maximum possi...

  20. Effects of NO x and VOCs from five emission sources on summer surface O3 over the Beijing-Tianjin-Hebei region

    Science.gov (United States)

    Qu, Yu; An, Junling; Li, Jian; Chen, Yong; Li, Ying; Liu, Xingang; Hu, Min

    2014-07-01

    The impacts of emissions from industry, power plant, transportation, residential, and biogenic sources on daily maximum surface ozone (O3DM) over the Beijing-Tianjin-Hebei (BTH) region in North China in the summer of 2007 were examined in a modeling study. The modeling system consisted of the Weather Research and Forecasting (WRF) model and the photochemical dispersion model, CAMx. The factor separation technique (FST) was used to quantify the effect of individual emission source types and the synergistic interactions among two or more types. Additionally, the effectiveness of emission reduction scenarios was explored. The industry, power plant, and transportation emission source types were found to be the most important in terms of their individual effects on O3DM. The key contributor to high surface O3 was power plant emissions, with a peak individual effect of 40 ppbv in the southwestern BTH area. The individual effect from the biogenic emission category was quite low. The synergistic effects from the combinations of each pair of anthropogenic emission types suppressed O3 formation, while the synergistic effects for combinations of three were favorable for O3 formation when the industrial and power plant emission source types coexisted. The quadruple synergistic effects were positive only with the combination of power plant, transportation, residential, and biogenic sources, while the quintuple synergistic effect showed only minor impacts on O3DM concentrations. A 30% reduction in industrial and transportation sources produced the most effective impacts on O3 concentrations, with a maximum decrease of 20 ppbv. These results suggested that the synergistic impacts among emission source types should be considered when formulating emission control strategies for O3 reduction.

  1. VOCs and odors: key factors in selecting `green` building materials?

    Energy Technology Data Exchange (ETDEWEB)

    Coombs, C. [Steven Winter Associates Inc., Norwalk, CT and Washington DC (United States)

    1998-12-01

    The current state of knowledge available for selecting building materials on the basis of emissions of volatile organic compounds (VOCs) and odors is reviewed. The significance of VOCs and odors in building materials is related to their role in influencing indoor air quality. As far as toxicity is concerned, many of the VOCs detected in indoor air are relatively inert when considered singly. They are not however, unimportant because in actual fact they are invariably found in mixtures some of which can be toxic. Although knowledge of VOCs is incomplete, it is important to specify ozone-resistant polymeric building products, i.e. those that are chemically stable and inert to oxidation. In addition to VOCs, attention should also be focused on semi-volatile organic compounds (SVOCs) since they are even more persistent than VOCs and tend to offgas for prolonged periods of time. Similarly, it is reasonable to specify low-odor materials. Inclusion of issues related to complex indoor chemistry, less volatile emissions, in addition to VOCs and odor, should in time result in expanded choices of building materials that promote indoor air quality. 16 refs.,2 tabs.

  2. Hydroxyl (6−2 airglow emission intensity ratios for rotational temperature determination

    Directory of Open Access Journals (Sweden)

    R. P. Lowe

    Full Text Available OH(6–2 Q1/P1 and R1/P1 airglow emission intensity ratios, for rotational states up to j' = 4.5, are measured to be lower than implied by transition probabilities published by various authors including Mies, Langhoff et al. and Turnbull and Lowe. Experimentally determined relative values of j' transitions yield OH(6–2 rotational temperatures 2 K lower than Langhoff et al., 7 K lower than Mies and 13 K lower than Turnbull and Lowe.Key words: Atmospheric composition and structure (airglow and aurora; pressure, density and temperature

  3. The Neutron Emission Ratio Observer NERO at the National Superconducting Cyclotron Laboratory

    Science.gov (United States)

    Pereira, Jorge; Hosmer, Paul; Lorusso, Giuseppe; Santi, Peter; Del Santo, Marcelo; Herlitzius, Clemens; Kratz, Karl-Ludwig; Montes, Fernando; Schatz, Hendrik; Schertz, Florian; Schnorrenberger, Linda; Smith, Karl; Wiescher, Michael

    2009-10-01

    The new neutron counter NERO (Neutron Emission Ratio Observer) was built at the National Superconducting Cyclotron Laboratory (NSCL) for measuring Pn values of neutron-rich nuclei produced as fast fragmentation beams. The design was motivated by the requirement of being coupled to the NSCL beta counting system, so that β-decay particles and neutrons emitted from implanted nuclei can be measured simultaneously, while keeping a high efficiency. The detector's performance and main features will be discussed, as well as recent measurements done at NSCL for astrophysical studies of the r-process.

  4. FeII/MgII Emission Line Ratio in High Redshift Quasars

    DEFF Research Database (Denmark)

    Dietrich, M.; Hamann, F.; Appenzeller, I.

    2003-01-01

    We present results of the analysis of near infrared spectroscopic observations of 6 high-redshift quasars (z > 4), emphasizing the measurement of the ultraviolet FeII/MgII emission line strength in order to estimate the beginning of intense star formation in the early universe. To investigate...... the evolution of the FeII/MgII ratio over a wider range in cosmic time, we measured this ratio for composite quasar spectra which cover a redshift range of 0 4 quasars must have started already at an epoch corresponding to z_f = 6 to 9, when the age of the universe was ~0.5 Gyr (H_o = 72 km/s/Mpc, Omega_M = 0...

  5. [Study on control and management for industrial volatile organic compounds (VOCs) in China].

    Science.gov (United States)

    Wang, Hai-Lin; Zhang, Guo-Ning; Nei, Lei; Wang, Yu-Fei; Hao, Zheng-Ping

    2011-12-01

    Volatile organic compounds (VOCs) emitted from industrial sources account for a large percent of total anthropogenic VOCs. In this paper, VOCs emission characterization, control technologies and management were discussed. VOCs from industrial emissions were characterized by high intensity, wide range and uneven distribution, which focused on Bejing-Tianjin Joint Belt, Shangdong Peninsula, Yangtze River Delta and the Pearl River Delta. The current technologies for VOCs treatment include adsorption, catalytic combustion, bio-degradation and others, which were applied in petrochemical, oil vapor recovery, shipbuilding, printing, pharmaceutical, feather manufacturing and so on. The scarcity of related regulations/standards plus ineffective supervision make the VOCs management difficult. Therefore, it is suggested that VOCs treatment be firstly performed from key areas and industries, and then carried out step by step. By establishing of actual reducing amount control system and more detailed VOCs emission standards and regulations, applying practical technologies together with demonstration projects, and setting up VOCs emission registration and classification-related-charge system, VOCs could be reduced effectively.

  6. Distortion product otoacoustic emission generation mechanisms and their dependence on stimulus level and primary frequency ratio.

    Science.gov (United States)

    Botti, Teresa; Sisto, Renata; Sanjust, Filippo; Moleti, Arturo; D'Amato, Luisa

    2016-02-01

    In this study, a systematic analysis of the dependence on stimulus level and primary frequency ratio r of the different components of human distortion product otoacoustic emissions has been performed, to check the validity of theoretical models of their generation, as regards the localization of the sources and the relative weight of distortion and reflection generation mechanisms. 2f1 - f2 and 2f2 - f1 distortion product otoacoustic emissions of 12 normal hearing ears from six human subjects have been measured at four different levels, in the range [35, 65] dB sound pressure level, at eight different ratios, in the range [1.1, 1.45]. Time-frequency filtering was used to separate distortion and reflection components. Numerical simulations have also been performed using an active nonlinear cochlear model. Both in the experiment and in the simulations, the behavior of the 2f1 - f2 distortion and reflection components was in agreement with previous measurements and with the predictions of the two-source model. The 2f2 - f1 response showed a rotating-phase component only, whose behavior was in general agreement with that predicted for a component generated and reflected within a region basal to the characteristic place of frequency 2f2 - f1, although alternative interpretations, which are also discussed, cannot be ruled out.

  7. Ozone response to emission changes: a modeling study during the MCMA-2006/MILAGRO campaign

    Directory of Open Access Journals (Sweden)

    R. Zhang

    2009-11-01

    Full Text Available The sensitivity of ozone production to precursor emissions was investigated under five different meteorological conditions in the Mexico City Metropolitan Area (MCMA during the MCMA-2006/MILAGRO field campaign using the gridded photochemical model CAMx driven by observation-nudged WRF meteorology. Precursor emissions were constrained by the comprehensive data from the field campaign and the routine ambient air quality monitoring network. Simulated plume mixing and transport were examined by comparing with measurements from the G-1 aircraft during the campaign. The observed concentrations of ozone precursors and ozone were well reproduced by the model. The effects of reducing precursor emissions on urban ozone production were performed for three representative emission control strategies. A 50% reduction in VOC emissions led to 7 to 22 ppb decrease in daily maximum ozone concentrations, while a 50% reduction in NOx emissions leads to 4 to 21 ppb increase, and 50% reductions in both NOx and VOC emission decrease the daily maximum ozone concentrations up to 10 ppb. These results along with a chemical indicator analysis using the chemical production ratios of H2O2 to HNO3 demonstrate that the MCMA urban core region is VOC-limited for all meteorological episodes, which is consistent with the results from MCMA-2003 field campaign; however the degree of the VOC-sensitivity is higher in the MCMA-2006 due to lower VOC/NOx emission ratio and VOC reactivity. Ozone formation in the surrounding mountain/rural area is mostly NOx-limited, but can be VOC-limited, and the range of the NOx-limited or VOC-limited areas depends on meteorology.

  8. VOC Composition of Air Masses Transported from Asia to the U.S. West Coast

    Science.gov (United States)

    de Gouw, J.; Warneke, C.; Kuster, B.; Parrish, D.; Holloway, J.; Huebler, G.; Fehsenfeld, F.

    2002-12-01

    Airborne measurements of volatile organic compounds (VOCs) were performed using a proton-transfer-reaction mass spectrometer (PTR-MS) operated onboard a NOAA WP-3 aircraft during the Intercontinental Transport and Chemical Transformation (ITCT) experiment in 2002. Enhancements of acetone (CH3COCH3), methanol (CH3OH), acetonitrile (CH3CN) and in some cases benzene were observed in air masses that were impacted by outflow from Asia. The enhancement ratios with respect to carbon monoxide are compared to emission factors for fossil fuel combustion and biomass burning, which gives some insight into the sources responsible for the pollution. The observed mixing ratios for acetone, methanol and in particular acetonitrile were generally reduced in the marine boundary layer, suggesting the presence of an ocean uptake sink. The ocean uptake of acetonitrile was found to be particularly efficient in a zone with upwelling water off of the U.S. west coast. Reduced mixing ratios of acetone and methanol were observed in a stratospheric intrusion. This observation gives some information about the lifetime of these VOCs in the stratosphere. Enhanced concentrations of aromatic hydrocarbons were observed in air masses that were impacted by urban sources in California. The ratio between the concentrations of benzene, toluene and higher aromatics indicated the degree of photochemical oxidation. PTR-MS only gives information about the mass of the ions produced by proton-transfer reactions between H3O+ and VOCs in the instrument. The identification of VOCs was confirmed by coupling a gas-chromatographic (GC) column to the instrument and post-flight GC-PTR-MS analyses of canister samples collected during the flights.

  9. Influence of Compression Ratio on the Performance and Emission Characteristics of Annona Methyl Ester Operated DI Diesel Engine

    Directory of Open Access Journals (Sweden)

    Senthil Ramalingam

    2014-09-01

    Full Text Available This study aims to find the optimum performance and emission characteristics of single cylinder variable compression ratio (VCR engine with different blends of Annona methyl ester (AME as fuel. The performance parameters such as specific fuel consumption (SFC, brake thermal efficiency (BTE, and emission levels of HC, CO, Smoke, and NOx were compared with the diesel fuel. It is found that, at compression ratio of 17: 1 for A20 blended fuel (20% AME + 80% Diesel shows better performance and lower emission level which is very close to neat diesel fuel. The engine was operated with different values of compression ratio (15, 16, and 17 to find out best possible combination for operating engine with blends of AME. It is also found that the increase of compression ratio increases the BTE and reduces SFC and has lower emission without any engine in design modifications.

  10. Farm-scale testing of soybean peroxidase and calcium peroxide for surficial swine manure treatment and mitigation of odorous VOCs, ammonia and hydrogen sulfide emissions

    Science.gov (United States)

    Maurer, Devin L.; Koziel, Jacek A.; Bruning, Kelsey; Parker, David B.

    2017-10-01

    The swine industry, regulatory agencies, and the public are interested in farm-tested methods for controlling gaseous emissions from swine barns. In earlier lab- and pilot-scale studies, a renewable catalyst consisting of soybean peroxidase (SBP) mixed with calcium peroxide (CaO2) was found to be effective in mitigating gaseous emissions from swine manure. Thus, a farm-scale experiment was conducted at the university's 178-pig, shallow-pit, mechanically-ventilated swine barn to evaluate SBP/CaO2 as a surficial manure pit additive under field conditions. The SBP was applied once at the beginning of the 42-day experiment at an application rate of 2.28 kg m-2 with 4.2% CaO2 added by weight. Gas samples were collected from the primary barn exhaust fans. As compared to the control, significant reductions in gaseous emissions were observed for ammonia (NH3, 21.7%), hydrogen sulfide (H2S, 79.7%), n-butyric acid (37.2%), valeric acid (47.7%), isovaleric acid (39.3%), indole (31.2%), and skatole (43.5%). Emissions of dimethyl disulfide/methanethiol (DMDS/MT) increased by 30.6%. Emissions of p-cresol were reduced by 14.4% but were not statistically significant. There were no significant changes to the greenhouse gas (GHG) emissions of methane (CH4), carbon dioxide (CO2) and nitrous oxide (N2O). The total (material + labor) treatment cost was 2.62 per marketed pig, equivalent to 1.5% of the pig market price. The cost of CaO2 catalyst was ∼60% of materials cost. The cost of soybean hulls (SBP source) was 0.60 per marketed pig, i.e., only 40% of materials cost.

  11. Significant light and temperature dependent monoterpene emissions from European beech (fagus sylvatiga L.) and their potential impact on the European VOC budget

    NARCIS (Netherlands)

    Dindorf, T.; Kuhn, U.; Ganzeveld, L.N.; Schebeske, G.; Ciccioli, P.; Holzke, C.; Köble, R.; Seufert, G.; Kesselmeier, J.

    2006-01-01

    By using a dynamic branch enclosure system the emission of monoterpenes from European beech (Fagus sylvatica L.) was investigated during two consecutive summer vegetation periods in the years of 2002 and 2003 in Germany. All measurements were performed under field conditions within the framework of

  12. Boreal forest fire emissions in fresh Canadian smoke plumes: C1-C10 volatile organic compounds (VOCs, CO2, CO, NO2, NO, HCN and CH3CN

    Directory of Open Access Journals (Sweden)

    M. Yang

    2011-07-01

    Full Text Available Boreal regions comprise about 17 % of the global land area, and they both affect and are influenced by climate change. To better understand boreal forest fire emissions and plume evolution, 947 whole air samples were collected aboard the NASA DC-8 research aircraft in summer 2008 as part of the ARCTAS-B field mission, and analyzed for 79 non-methane volatile organic compounds (NMVOCs using gas chromatography. Together with simultaneous measurements of CO2, CO, CH4, CH2O, NO2, NO, HCN and CH3CN, these measurements represent the most comprehensive assessment of trace gas emissions from boreal forest fires to date. Based on 105 air samples collected in fresh Canadian smoke plumes, 57 of the 80 measured NMVOCs (including CH2O were emitted from the fires, including 45 species that were quantified from boreal forest fires for the first time. After CO2, CO and CH4, the largest emission factors (EFs for individual species were formaldehyde (2.1 ± 0.2 g kg−1, followed by methanol, NO2, HCN, ethene, α-pinene, β-pinene, ethane, benzene, propene, acetone and CH3CN. Globally, we estimate that boreal forest fires release 2.4 ± 0.6 Tg C yr−1 in the form of NMVOCs, with approximately 41 % of the carbon released as C1-C2 NMVOCs and 21 % as pinenes. These are the first reported field measurements of monoterpene emissions from boreal forest fires, and we speculate that the pinenes, which are relatively heavy molecules, were detected in the fire plumes as the result of distillation of stored terpenes as the vegetation is heated. Their inclusion in smoke chemistry models is expected to improve model predictions of secondary organic aerosol (SOA formation. The fire-averaged EF of dichloromethane or CH2Cl2, (6.9 ± 8.6 × 10−4 g kg−1, was not significantly different from zero and supports recent findings that its global biomass burning source appears to have been overestimated. Similarly, we found no evidence for emissions of chloroform (CHCl3 or methyl

  13. Effect of compression ratio on the performance, combustion and emission from a diesel engine using palm biodiesel

    Science.gov (United States)

    Datta, Ambarish; Mandal, Bijan Kumar

    2016-07-01

    The authors have simulated a single cylinder diesel engine using Diesel-RK software to investigate the performance, emission and combustion characteristics of the engine using palm biodiesel and petro-diesel. The simulation has been carried out for three compression ratios of 16, 17 and 18 at constant speed of 1500 rpm. The analysis of simulation results show that brake thermal efficiency decreases and brake specific fuel consumption increases with the use of palm biodiesel instead of diesel. The thermal efficiency increases and the brake specific fuel consumption decreases with the increase of compression ratio. The higher compression ratio results in higher in-cylinder pressure and higher heat release rate as well as lower ignition delay. The NOx and CO2 emissions increase at higher compression ratio due to the higher pressure and temperature. On the other hand, the specific PM emission and smoke opacity are less at higher compression ratio.

  14. Low VOC drying of lumber and wood panel products. Progress report No. 5

    Energy Technology Data Exchange (ETDEWEB)

    Wild, P.; Yan, Hui; Banerjee, S. [and others

    1997-10-01

    This progress report summarizes three accomplishments in a study of low volatile organic compound (VOC) drying of lumber and wood panel products. A mathematical model for predicting moisture emissions from particle was constructed and is being extended to VOCs. VOCs emissions from drying boards show that VOCs appear to be evenly released from all surfaces. Preliminary results from monthly analyses of loblolly pines indicate that resin acids appear to decrease between March to August, and that no consistent trends are apparent for terpenes. 3 refs., 13 figs., 1 tab.

  15. Implementation of VOC source reduction practices in a manufactured house and in school classrooms

    Energy Technology Data Exchange (ETDEWEB)

    Hodgson, A.T.; Apte, M.G.; Shendell, D.G.; Beal, D.; McIlvaine, J.E.R.

    2002-01-01

    Detailed studies of a new manufactured house and four new industrialized relocatable school classrooms were conducted to determine the emission sources of formaldehyde and other VOCs and to identify and implement source reduction practices. Procedures were developed to generate VOC emission factors that allowed reasonably accurate predictions of indoor air VOC concentrations. Based on the identified sources of formaldehyde and other aldehydes, practices were developed to reduce the concentrations of these compounds in new house construction. An alternate ceiling panel reduced formaldehyde concentrations in the classrooms. Overall, the classrooms had relatively low VOC concentrations.

  16. Assessment of regional influence from a petrochemical complex by modeling and fingerprint analysis of volatile organic compounds (VOCs)

    Science.gov (United States)

    Su, Yuan-Chang; Chen, Sheng-Po; Tong, Yu-Huei; Fan, Chen-Lun; Chen, Wei-Hao; Wang, Jia-Lin; Chang, Julius S.

    2016-09-01

    This study aimed to demonstrate a strategy to investigate the influence of volatile organic compounds (VOCs) on its neighboring districts from a gigantic petrochemical complex. Monitoring of the VOCs in the region was achieved by a nine-station network, dubbed photochemical assessment measurement stations (PAMS), which produced speciated mixing ratios of 54 non-methane hydrocarbons (NMHCs) to represent VOCs with an hourly resolution within a 20 km radius. One-year (2013/10/1-2014/9/30) worth of PAMS data from the network were used in forms of total NMHCs (called PAMS-TNMHC) and speciated mixing ratios. Three dimensional modeling coupled with PAMS measurements successfully elucidated how the study domain was affected by the petrochemical complex and distant sources under three typical seasonal wind patterns: northeast monsoonal, southwest monsoonal, and local-circulation. More exquisite analysis of influence on the neighboring districts was permitted with the use of speciated mixing ratios of VOCs provided by the PAMS network. The ratios of ethylene/acetylene (E/A) > 3 and propylene/acetylene (P/A) > 1.5 were used as indicators to reveal the PAMS sites affected by the petrochemical emissions. Consequently, the hourly speciated data from the nine PAMS sites enabled a finer assessment of the districts affected by the complex to calculate the percent time of influence (dubbed TI%) for all the sites (districts). It was found that the region was more affected by the complex under both the northeast monsoonal and the local-circulation wind types with some of the PAMS sites greater than 5% for the TI%. By contrast, influence on the region was found minimal under the southwest monsoonal flow with the TI% small than 1.5% across all sites. This study successfully devised a method of assessment with the use of speciated measurements of selected VOCs and modeling to assess the influence of a prominent source on the neighboring districts by filtering out irrelevant sources under

  17. Multi-images deconvolution improves signal-to-noise ratio on gated stimulated emission depletion microscopy

    Energy Technology Data Exchange (ETDEWEB)

    Castello, Marco [Nanobiophotonics, Nanophysics, Istituto Italiano di Tecnologia, Via Morego 30, Genoa, 16163 (Italy); DIBRIS, University of Genoa, Via Opera Pia 13, Genoa 16145 (Italy); Diaspro, Alberto [Nanobiophotonics, Nanophysics, Istituto Italiano di Tecnologia, Via Morego 30, Genoa, 16163 (Italy); Nikon Imaging Center, Via Morego 30, Genoa 16163 (Italy); Vicidomini, Giuseppe, E-mail: giuseppe.vicidomini@iit.it [Nanobiophotonics, Nanophysics, Istituto Italiano di Tecnologia, Via Morego 30, Genoa, 16163 (Italy)

    2014-12-08

    Time-gated detection, namely, only collecting the fluorescence photons after a time-delay from the excitation events, reduces complexity, cost, and illumination intensity of a stimulated emission depletion (STED) microscope. In the gated continuous-wave- (CW-) STED implementation, the spatial resolution improves with increased time-delay, but the signal-to-noise ratio (SNR) reduces. Thus, in sub-optimal conditions, such as a low photon-budget regime, the SNR reduction can cancel-out the expected gain in resolution. Here, we propose a method which does not discard photons, but instead collects all the photons in different time-gates and recombines them through a multi-image deconvolution. Our results, obtained on simulated and experimental data, show that the SNR of the restored image improves relative to the gated image, thereby improving the effective resolution.

  18. Estimate of anthropogenic halocarbon emission based on measured ratio relative to CO in the Pearl River Delta region, China

    Science.gov (United States)

    Shao, M.; Huang, D.; Gu, D.; Lu, S.; Chang, C.; Wang, J.

    2011-05-01

    Using a GC/FID/MS system, we analyzed the mixing ratio of 16 halocarbon species in more than 100 air samples collected in 2004 from the Pearl River Delta (PRD) region of southern China. The results revealed that there are elevated mixing ratios for most of halocarbons, especially for HClC = CCl2 (trichloroethylene, TCE), CH2Cl2 (dichloromethane, DCM), CH3 Br (bromomethane), HCFC-22, CHCl3 (trichloromethane), CCl4 (tetrachloromethane), Cl2C = CCl2 (perchloroethylene, PCE), CH3CCl3 (methyl chloroform, MCF), and CFC-12. Comparisons were done with the data from TRACE-P and ALE/GAGE/AGAGE experiments, we found that the large variability in mixing ratios (relative standard deviation ranged from 9.31 % to 96.55 %) of the halocarbons suggested substantial local emissions from the PRD region in 2004. Correlations between the mixing ratio of each species and carbon monoxide (CO) was examined, and then the emission of each halocarbon was quantified based on scaling the optimized CO emission inventory with the slope of the regression line fitted to each species relative to CO. The calculated results revealed that mass of CH2Cl2 (7.0 Gg), CH3CCl3 (6.7 Gg), and Cl2C = CCl2 (2.3 Gg) accounted for about 62.9 % of total halocarbon emissions, it suggested a significant contribution from solvent use in the PRD region. Emissions of HCFC-22 (3.5 Gg), an alternative refrigerant to chlorofluorocarbons (CFCs), were about 2.3 times greater than those of CFC-12 (1.6 Gg). CFC-12 and HCFC-22 accounted for 21.5 % of total emissions of halocarbons, so that the refrigerant would be the second largest source of halocarbons. However, the ratio approach found only minor emissions of CFCs, such as CFC-11, and the emission of CFC-114 and CFC-113 were close to zero. Emissions of other anthropogenic halocarbons, such as CCl4, CHCl3, CH3Br, and CH3Cl, were also estimated. Where possible, the emissions estimated from the measured ratios were compared with results from source inventory techniques, we

  19. Dejima VOC dan rangaku

    Directory of Open Access Journals (Sweden)

    Bambang Wibawarta

    2008-10-01

    Full Text Available Japan and the Netherlands have maintained a special relationship for about 300years since the adoption of the National Seclusion policy, the so-called sakoku bythe Tokugawa shogunate (1603-1867. The Dutch began trading with Japan andengaging with Japanese society in 1600, when a Dutch ship, De Liefde, arrived inKyushu. The Tokugawa government measures regarding foreign policy includedregulations on foreign access to Japan and a prohibition on Japanese goingabroad. Between the middle of the seventeenth to the early nineteenth century,Japan was characterized by a stable political pattern in which representativesof the VOC (Dutch East India Company, were the only Europeans with a rightto trade in Japan. In the course of this period, the Japanese evaluation of theDutch changed from regarding them as commercial agents to seeing them asimporters of European knowledge. This paper is especially concerned with theinfluence of the so-called ‘Dutch Studies’ (rangaku on the early modernizationof Japan, especially with regard to medicine and the natural sciences. Thisresearch examines the development of rangaku and the trading between Japanand VOC at Dejima.

  20. Estimates of anthropogenic halocarbon emissions based on its measured ratios relative to CO in the Pearl River Delta

    Science.gov (United States)

    Shao, M.; Huang, D. K.; Gu, D. S.; Lu, S. H.; Chang, C. C.; Wang, J.-L.

    2011-01-01

    Using a GC/FID/MS system, we analyzed the mixing ratio levels of 16 halocarbon species in more than 100 air samples collected in 2004 from the Pearl River Delta (PRD) region of southern China. The results revealed elevated regional mixing ratios for most halocarbons, especially for HClC = CCl2 (trichloroethylene, TCE), CH2Cl2 (dichloromethane, DCM), CH3Br (bromomethane), HCFC-22, CHCl3 (trichloromethane), CCl4 (tetrachloromethane), Cl2C = CCl2 (perchloroethylene, PCE), CH3CCl3 (methyl chloroform, MCF), and CFC-12. Comparisons were done with the data from TRACE-P and ALE/GAGE/AGAGE experiments, we found that the large variability in concentrations (relative standard deviation ranged from 9.31% to 96.55%) of the halocarbons suggested substantial local emissions from the PRD region in 2004. Correlations between the mixing ratio of each species and carbon monoxide (CO) were examined, and then each emission of halocarbon was quantified based on scaling the optimized CO emission inventory with the slope of the regression line fitted to each species relative to CO. The calculated results revealed that mass of CH2Cl2 (7.0 Gg), CH3CCl3 (6.7 Gg), and Cl2C = CCl2 (2.3 Gg) accounted for about 62.9% of total emissions, suggesting a significant contribution to halocarbon emissions from solvent use in the PRD region. Emissions of HCFC-22 (3.5 Gg), an alternative refrigerant to chlorofluorocarbons (CFCs), were about 2.3 times greater than those of CFC-12 (1.6 Gg). CFC-12 and HCFC-22 accounted for 21.5% of total emissions of halocarbons, so that the refrigerant would be the second largest source of halocarbons. However, the ratio approach found only minor emissions of other CFCs, such as CFC-11, and levels of CFC-114 and CFC-113 were close to zero. Emissions of other anthropogenic halocarbons, such as CCl4, CHCl3, CH3Br, and CH3Cl, were also estimated. Where possible, the emissions estimated from the measured ratios were compared with results from source inventory techniques, we

  1. EFFECT OF COMPRESSION RATIO ON ENERGY AND EMISSION OF VCR DIESEL ENGINE FUELLED WITH DUAL BLENDS OF BIODIESEL

    Directory of Open Access Journals (Sweden)

    R. D. EKNATH

    2014-10-01

    Full Text Available In recent 10 years biodiesel fuel was studied extensively as an alternative fuel. Most of researchers reported performance and emission of biodiesel and their blends with constant compression ratio. Also all the research was conducted with use of single biodiesel and its blend. Few reports are observed with the use of variable compression ratio and blends of more than one biodiesel. Main aim of the present study is to analyse the effect of compression ratio on the performance and emission of dual blends of biodiesel. In the present study Blends of Jatropha and Karanja with Diesel fuel was tested on single cylinder VCR DI diesel engine for compression ratio 16 and 18. High density of biodiesel fuel causes longer delay period for Jatropha fuel was observed compare with Karanja fuel. However blending of two biodiesel K20J40D results in to low mean gas temperature which is the main reason for low NOx emission.

  2. Ozone response to emission changes: a modeling study during the MCMA-2006/MILAGRO Campaign

    Directory of Open Access Journals (Sweden)

    J. Song

    2010-04-01

    Full Text Available The sensitivity of ozone production to precursor emissions was investigated under five different meteorological conditions in the Mexico City Metropolitan Area (MCMA during the MCMA-2006/MILAGRO field campaign using the gridded photochemical model CAMx driven by observation-nudged WRF meteorology. Precursor emissions were constrained by the comprehensive data from the field campaign and the routine ambient air quality monitoring network. Simulated plume mixing and transport were examined by comparing with measurements from the G-1 aircraft during the campaign. The observed concentrations of ozone precursors and ozone were reasonably well reproduced by the model. The effects of reducing precursor emissions on urban ozone production were performed for three representative emission control scenarios. A 50% reduction in VOC emissions led to 7 to 22 ppb decrease in daily maximum ozone concentrations, while a 50% reduction in NOx emissions leads to 4 to 21 ppb increase, and 50% reductions in both NOx and VOC emission decrease the daily maximum ozone concentrations up to 10 ppb. These results along with a chemical indicator analysis using the chemical production ratios of H2O2 to HNO3 demonstrate that the MCMA urban core region is VOC-limited for all meteorological episodes, which is consistent with the results from MCMA-2003 field campaign; however the degree of the VOC-sensitivity is higher during MCMA-2006 due to lower VOCs, lower VOC reactivity and moderately higher NOx emissions. Ozone formation in the surrounding mountain/rural area is mostly NOx-limited, but can be VOC-limited, and the range of the NOx-limited or VOC-limited areas depends on meteorology.

  3. Ozone production and its sensitivity to NOx and VOCs: results from the DISCOVER-AQ field experiment, Houston 2013

    Science.gov (United States)

    Mazzuca, Gina M.; Ren, Xinrong; Loughner, Christopher P.; Estes, Mark; Crawford, James H.; Pickering, Kenneth E.; Weinheimer, Andrew J.; Dickerson, Russell R.

    2016-11-01

    An observation-constrained box model based on the Carbon Bond mechanism, version 5 (CB05), was used to study photochemical processes along the NASA P-3B flight track and spirals over eight surface sites during the September 2013 Houston, Texas deployment of the NASA Deriving Information on Surface Conditions from COlumn and VERtically Resolved Observations Relevant to Air Quality (DISCOVER-AQ) campaign. Data from this campaign provided an opportunity to examine and improve our understanding of atmospheric photochemical oxidation processes related to the formation of secondary air pollutants such as ozone (O3). O3 production and its sensitivity to NOx and volatile organic compounds (VOCs) were calculated at different locations and times of day. Ozone production efficiency (OPE), defined as the ratio of the ozone production rate to the NOx oxidation rate, was calculated using the observations and the simulation results of the box and Community Multiscale Air Quality (CMAQ) models. Correlations of these results with other parameters, such as radical sources and NOx mixing ratio, were also evaluated. It was generally found that O3 production tends to be more VOC-sensitive in the morning along with high ozone production rates, suggesting that control of VOCs may be an effective way to control O3 in Houston. In the afternoon, O3 production was found to be mainly NOx-sensitive with some exceptions. O3 production near major emissions sources such as Deer Park was mostly VOC-sensitive for the entire day, other urban areas near Moody Tower and Channelview were VOC-sensitive or in the transition regime, and areas farther from downtown Houston such as Smith Point and Conroe were mostly NOx-sensitive for the entire day. It was also found that the control of NOx emissions has reduced O3 concentrations over Houston but has led to larger OPE values. The results from this work strengthen our understanding of O3 production; they indicate that controlling NOx emissions will provide

  4. Top-Down Constraints on the Emissions of Anthropogenic Volatile Organic Compounds from a Mega-City

    Science.gov (United States)

    De Gouw, J. A.; Warneke, C.; Borbon, A.; Gilman, J. B.; Kuster, W. C.; Parrish, D. D.; Atlas, E. L.; Blake, D. R.

    2012-12-01

    During the CalNex study in May-June of 2010, an extensive set of volatile organic compounds (VOCs) was measured in the Los Angeles basin and its in- and outflow areas. Measurements were made from the NOAA WP-3D research aircraft, the research vessel Atlantis and a ground site in Pasadena, California. In this presentation, the results are used to derive top-down constraints on the emissions of anthropogenic VOCs from this North-American megacity. The VOC data from CalNex in 2010 are put in perspective by comparing them with results from an earlier flight of the NOAA WP-3D in the Los Angeles basin in 2002, from a number of other earlier studies and from two different air quality monitoring networks. Strongly decreasing trends of ~7% per year are observed for most VOCs that are emitted from motor vehicles or photo-chemically produced from these emissions. Decreasing trends are less strong for small alkanes, which are mostly from natural gas related emissions, and oxygenated VOCs produced from them. The composition of urban VOC emissions was determined using the data obtained by gas-chromatography mass spectrometry at the ground site in Pasadena. Emission ratios of hydrocarbons versus ethyne were obtained using two methods. First, emission ratios were determined from nighttime data only. Second, the degree of photochemical processing of the sampled air masses was estimated, and emission ratios were determined by extrapolating to a zero photochemical age. Both methods agreed within the combined uncertainties for most VOCs. The composition of urban VOC emissions in Los Angeles was compared with other urban regions including in the U.S. and Europe and found to be similar. Measurements of ethanol at the ground site in Pasadena showed much higher mixing ratios than observed earlier in the northeastern U.S. The difference is attributed in part to the strongly increased use of fuel ethanol in the U.S.: in 2010, about 10% of gasoline consisted of ethanol, whereas that

  5. Characterization of polycyclic aromatic hydrocarbon emissions in the particulate phase from burning incenses with various atomic hydrogen/carbon ratios

    Energy Technology Data Exchange (ETDEWEB)

    Yang, Tzu-Ting, E-mail: d89844001@ntu.edu.tw [Department of Environmental Engineering and Health, Yuanpei University, No. 306, Yuanpei St., Hsin Chu, 300, Taiwan (China); Lin, Shaw-Tao [Department of Applied Chemistry, Providence University, 200 Chung-Chi Rd., Salu Dist., Taichung City 43301, Taiwan (China); Lin, Tser-Sheng [Department of Safety, Health, and Environmental Engineering, National United University, 2 Lien Da, Maioli, 360, Taiwan (China); Hong, Wei-Lun [Department of Environmental Engineering and Health, Yuanpei University, No. 306, Yuanpei St., Hsin Chu, 300, Taiwan (China)

    2012-01-01

    Polycyclic aromatic hydrocarbons in the particulate phase generated from burning various incense was investigated by a gas chromatography/mass spectrometry. Among the used incenses, the atomic H/C ratio ranged from 0.51 to 1.69, yielding the emission factor ranges for total particulate mass and PAHs of 4.19-82.16 mg/g and 1.20-9.50 {mu}g/g, respectively. The atomic H/C ratio of the incense was the key factor affecting particulate mass and the PAHs emission factors. Both the maximum emission factor and the slowest burning rate appear at the H/C ratio of 1.57. The concentrations of the four-ring PAHs predominated and the major species among the 16 PAHs were fluoranthene, phenanthrene, pyrene, and chrysene for most incense types. The benzo[a]pyrene, benzo[a]anthracene, benzo[b]fluoranthene, and dibenzo[a,h]anthracene accounted for 87.08-93.47% of the total toxic equivalency emission factor. - Highlights: Black-Right-Pointing-Pointer The atomic H/C ratio of incense was the key factor affecting PAHs emission factors. Black-Right-Pointing-Pointer Burning incense with lower atomic H/C ratio minimized the production of total PAHs. Black-Right-Pointing-Pointer The BaP, BaA, BbF, and DBA accounted for 87.08-93.47% of the TEQ emission factor. Black-Right-Pointing-Pointer Special PAH ratios were regarded as characteristic ratios for burning incense.

  6. Similarity ratio analysis for early stage fault detection with optical emission spectrometer in plasma etching process.

    Science.gov (United States)

    Yang, Jie; McArdle, Conor; Daniels, Stephen

    2014-01-01

    A Similarity Ratio Analysis (SRA) method is proposed for early-stage Fault Detection (FD) in plasma etching processes using real-time Optical Emission Spectrometer (OES) data as input. The SRA method can help to realise a highly precise control system by detecting abnormal etch-rate faults in real-time during an etching process. The method processes spectrum scans at successive time points and uses a windowing mechanism over the time series to alleviate problems with timing uncertainties due to process shift from one process run to another. A SRA library is first built to capture features of a healthy etching process. By comparing with the SRA library, a Similarity Ratio (SR) statistic is then calculated for each spectrum scan as the monitored process progresses. A fault detection mechanism, named 3-Warning-1-Alarm (3W1A), takes the SR values as inputs and triggers a system alarm when certain conditions are satisfied. This design reduces the chance of false alarm, and provides a reliable fault reporting service. The SRA method is demonstrated on a real semiconductor manufacturing dataset. The effectiveness of SRA-based fault detection is evaluated using a time-series SR test and also using a post-process SR test. The time-series SR provides an early-stage fault detection service, so less energy and materials will be wasted by faulty processing. The post-process SR provides a fault detection service with higher reliability than the time-series SR, but with fault testing conducted only after each process run completes.

  7. Similarity ratio analysis for early stage fault detection with optical emission spectrometer in plasma etching process.

    Directory of Open Access Journals (Sweden)

    Jie Yang

    Full Text Available A Similarity Ratio Analysis (SRA method is proposed for early-stage Fault Detection (FD in plasma etching processes using real-time Optical Emission Spectrometer (OES data as input. The SRA method can help to realise a highly precise control system by detecting abnormal etch-rate faults in real-time during an etching process. The method processes spectrum scans at successive time points and uses a windowing mechanism over the time series to alleviate problems with timing uncertainties due to process shift from one process run to another. A SRA library is first built to capture features of a healthy etching process. By comparing with the SRA library, a Similarity Ratio (SR statistic is then calculated for each spectrum scan as the monitored process progresses. A fault detection mechanism, named 3-Warning-1-Alarm (3W1A, takes the SR values as inputs and triggers a system alarm when certain conditions are satisfied. This design reduces the chance of false alarm, and provides a reliable fault reporting service. The SRA method is demonstrated on a real semiconductor manufacturing dataset. The effectiveness of SRA-based fault detection is evaluated using a time-series SR test and also using a post-process SR test. The time-series SR provides an early-stage fault detection service, so less energy and materials will be wasted by faulty processing. The post-process SR provides a fault detection service with higher reliability than the time-series SR, but with fault testing conducted only after each process run completes.

  8. Development of net energy ratio and emission factor for biohydrogen production pathways.

    Science.gov (United States)

    Kabir, Md Ruhul; Kumar, Amit

    2011-10-01

    This study investigates the energy and environmental aspects of producing biohydrogen for bitumen upgrading from a life cycle perspective. Three technologies are studied for biohydrogen production; these include the Battelle Columbus Laboratory (BCL) gasifier, the Gas Technology Institute (GTI) gasifier, and fast pyrolysis. Three different biomass feedstocks are considered including forest residue (FR), whole forest (WF), and agricultural residue (AR). The fast pyrolysis pathway includes two cases: truck transport of bio-oil and pipeline transport of bio-oil. The net energy ratios (NERs) for nine biohydrogen pathways lie in the range of 1.3-9.3. The maximum NER (9.3) is for the FR-based pathway using GTI technology. The GHG emissions lie in the range of 1.20-8.1 kg CO₂ eq/kg H₂. The lowest limit corresponds to the FR-based biohydrogen production pathway using GTI technology. This study also analyzes the intensities for acid rain precursor and ground level ozone precursor.

  9. Emission Ratios of the Tropospheric Ozone Precursors Nitrogen Dioxide and Formaldehyde from Australia’s Black Saturday Fires

    Directory of Open Access Journals (Sweden)

    Clare Paton-Walsh

    2011-10-01

    Full Text Available The ‘Black Saturday’ fires were a series of devastating forest fires that burned across Victoria, Australia, during February and March of 2009. In this study we have used satellite data made publically available by NASA from the Ozone Monitoring Instrument (OMI and the Atmospheric InfraRed Sounder (AIRS to track the smoke plume from the Black Saturday firestorm and explore the chemical aging of the smoke plume in the first days after emission. We also determined emission ratios for formaldehyde and nitrogen dioxide within smoke from fires actively burning across Victoria between 7 and 17 February 2009. The mean emission ratios with respect to carbon monoxide derived for these two tropospheric ozone precursors are (0.016 ± 0.004 mol.mol−1 for formaldehyde and (0.005 ± 0.002 mol.mol−1 for nitrogen dioxide. The mean emission ratio for formaldehyde with respect to CO is in broad agreement with values previously quoted in the literature for temperate forest fires. However, to our knowledge there are no previous measurements of emission ratios for nitrogen dioxide from Australian temperate forest fires.

  10. A comparative study in treating two VOC mixtures in trickle bed air biofilters.

    Science.gov (United States)

    Cai, Zhangli; Kim, Daekeun; Sorial, George A

    2007-06-01

    Two independent parallel trickling bed air biofilters (TBABs) ("A" and "B") with two different typical VOC mixtures were investigated. Toluene, styrene, methyl ethyl ketone (MEK), and methyl isobutyl ketone (MIBK) were the target VOCs in the mixtures. Biofilter "A" was fed equal molar ratio of the VOCs and biofilter "B" was fed a mixture based on EPA 2003 emission report. Backwashing and substrate starvation operation were conducted as biomass control. Biofilter "A" and "B" maintained 99% overall removal efficiency for influent concentration up to 500 and 300 ppmv under backwashing operating condition, respectively. The starvation study indicated that it can be an effective biomass control for influent concentrations up to 250 ppmv for biofilter "A" and 300 ppmv for "B". Re-acclimation of biofilter performance was delayed with increase of influent concentration for both biofilters. Starvation operation helped the biofilter to recover at low concentrations and delayed re-acclimation at high concentrations. Furthermore, re-acclamation for biofilter "B" was delayed due to its high toluene content as compared to biofilter "A". The pseudo first-order removal rate constant decreased with increase of volumetric loading rate for both biofilters. MEK and MIBK were completely removed in the upper 3/8 media depth. While biofilter depth utilization for the removal of styrene and toluene increased with increase of influent concentrations for both biofilters. However, toluene removal utilized more biofilter depth for biofilter "B" as compared to biofilter "A".

  11. Performance and exhaust emission characteristics of variable compression ratio diesel engine fuelled with esters of crude rice bran oil.

    Science.gov (United States)

    Vasudeva, Mohit; Sharma, Sumeet; Mohapatra, S K; Kundu, Krishnendu

    2016-01-01

    As a substitute to petroleum-derived diesel, biodiesel has high potential as a renewable and environment friendly energy source. For petroleum importing countries the choice of feedstock for biodiesel production within the geographical region is a major influential factor. Crude rice bran oil is found to be good and viable feedstock for biodiesel production. A two step esterification is carried out for higher free fatty acid crude rice bran oil. Blends of 10, 20 and 40 % by vol. crude rice bran biodiesel are tested in a variable compression ratio diesel engine at compression ratio 15, 16, 17 and 18. Engine performance and exhaust emission parameters are examined. Cylinder pressure-crank angle variation is also plotted. The increase in compression ratio from 15 to 18 resulted in 18.6 % decrease in brake specific fuel consumption and 14.66 % increase in brake thermal efficiency on an average. Cylinder pressure increases by 15 % when compression ratio is increased. Carbon monoxide emission decreased by 22.27 %, hydrocarbon decreased by 38.4 %, carbon dioxide increased by 17.43 % and oxides of nitrogen as NOx emission increased by 22.76 % on an average when compression ratio is increased from 15 to 18. The blends of crude rice bran biodiesel show better results than diesel with increase in compression ratio.

  12. Estimate of anthropogenic halocarbon emission based on measured ratio relative to CO in the Pearl River Delta region, China

    Directory of Open Access Journals (Sweden)

    M. Shao

    2011-05-01

    Full Text Available Using a GC/FID/MS system, we analyzed the mixing ratio of 16 halocarbon species in more than 100 air samples collected in 2004 from the Pearl River Delta (PRD region of southern China. The results revealed that there are elevated mixing ratios for most of halocarbons, especially for HClC = CCl2 (trichloroethylene, TCE, CH2Cl2 (dichloromethane, DCM, CH3 Br (bromomethane, HCFC-22, CHCl3 (trichloromethane, CCl4 (tetrachloromethane, Cl2C = CCl2 (perchloroethylene, PCE, CH3CCl3 (methyl chloroform, MCF, and CFC-12. Comparisons were done with the data from TRACE-P and ALE/GAGE/AGAGE experiments, we found that the large variability in mixing ratios (relative standard deviation ranged from 9.31 % to 96.55 % of the halocarbons suggested substantial local emissions from the PRD region in 2004. Correlations between the mixing ratio of each species and carbon monoxide (CO was examined, and then the emission of each halocarbon was quantified based on scaling the optimized CO emission inventory with the slope of the regression line fitted to each species relative to CO. The calculated results revealed that mass of CH2Cl2 (7.0 Gg, CH3CCl3 (6.7 Gg, and Cl2C = CCl2 (2.3 Gg accounted for about 62.9 % of total halocarbon emissions, it suggested a significant contribution from solvent use in the PRD region. Emissions of HCFC-22 (3.5 Gg, an alternative refrigerant to chlorofluorocarbons (CFCs, were about 2.3 times greater than those of CFC-12 (1.6 Gg. CFC-12 and HCFC-22 accounted for 21.5 % of total emissions of halocarbons, so that the refrigerant would be the second largest source of halocarbons. However, the ratio approach found only minor emissions of CFCs, such as CFC-11, and the emission of CFC-114 and CFC-113 were close to zero. Emissions of other anthropogenic halocarbons, such as CCl

  13. Reduction of odorous VOC in phenolics solutions and swine manure slurry using soybean peroxidase and hydrogen peroxide

    Science.gov (United States)

    A research project was conducted to evaluate the efficacy of low-activity soybean peroxidase (SBP; 0.75 U/mg) and H2O2 for reducing emissions of odorous volatile organic compounds (VOC) from standard solutions (phenol and 4-methylphenol; 1 mM each) and swine manure slurry. VOC emissions were measu...

  14. Estimates of anthropogenic halocarbon emissions based on its measured ratios relative to CO in the Pearl River Delta

    Directory of Open Access Journals (Sweden)

    M. Shao

    2011-01-01

    Full Text Available Using a GC/FID/MS system, we analyzed the mixing ratio levels of 16 halocarbon species in more than 100 air samples collected in 2004 from the Pearl River Delta (PRD region of southern China. The results revealed elevated regional mixing ratios for most halocarbons, especially for HClC = CCl2 (trichloroethylene, TCE, CH2Cl2 (dichloromethane, DCM, CH3Br (bromomethane, HCFC-22, CHCl3 (trichloromethane, CCl4 (tetrachloromethane, Cl2C = CCl2 (perchloroethylene, PCE, CH3CCl3 (methyl chloroform, MCF, and CFC-12. Comparisons were done with the data from TRACE-P and ALE/GAGE/AGAGE experiments, we found that the large variability in concentrations (relative standard deviation ranged from 9.31% to 96.55% of the halocarbons suggested substantial local emissions from the PRD region in 2004. Correlations between the mixing ratio of each species and carbon monoxide (CO were examined, and then each emission of halocarbon was quantified based on scaling the optimized CO emission inventory with the slope of the regression line fitted to each species relative to CO. The calculated results revealed that mass of CH2Cl2 (7.0 Gg, CH3CCl3 (6.7 Gg, and Cl2C = CCl2 (2.3 Gg accounted for about 62.9% of total emissions, suggesting a significant contribution to halocarbon emissions from solvent use in the PRD region. Emissions of HCFC-22 (3.5 Gg, an alternative refrigerant to chlorofluorocarbons (CFCs, were about 2.3 times greater than those of CFC-12 (1.6 Gg. CFC-12 and HCFC-22 accounted for 21.5% of total emissions of halocarbons, so that the refrigerant would be the second largest source of halocarbons. However, the ratio approach found only minor emissions of other CFCs, such as CFC-11, and levels of CFC-114 and CFC-113 were close to zero. Emissions of other anthropogenic halocarbons, such as CCl

  15. Emission Ratios for Ammonia and Formic Acid and Observations of Peroxy Acetyl Nitrate (PAN and Ethylene in Biomass Burning Smoke as Seen by the Tropospheric Emission Spectrometer (TES

    Directory of Open Access Journals (Sweden)

    Vivienne H. Payne

    2011-11-01

    Full Text Available We use the Tropospheric Emission Spectrometer (TES aboard the NASA Aura satellite to determine the concentrations of the trace gases ammonia (NH3 and formic acid (HCOOH within boreal biomass burning plumes, and present the first detection of peroxy acetyl nitrate (PAN and ethylene (C2H4 by TES. We focus on two fresh Canadian plumes observed by TES in the summer of 2008 as part of the Arctic Research of the Composition of the Troposphere from Aircraft and Satellites (ARCTAS-B campaign. We use TES retrievals of NH3 and HCOOH within the smoke plumes to calculate their emission ratios (1.0% ± 0.5% and 0.31% ± 0.21%, respectively relative to CO for these Canadian fires. The TES derived emission ratios for these gases agree well with previous aircraft and satellite estimates, and can complement ground-based studies that have greater surface sensitivity. We find that TES observes PAN mixing ratios of ~2 ppb within these mid-tropospheric boreal biomass burning plumes when the average cloud optical depth is low ( < 0.1 and that TES can detect C2H4 mixing ratios of ~2 ppb in fresh biomass burning smoke plumes.

  16. EVALUATION AND PERFORMANCE ASSESSMENT OF INNOVATIVE LOW-VOC CONTACT ADHESIVES IN WOOD LAMINATING OPERATIONS

    Science.gov (United States)

    The report gives results of an evaluation and assessment of the perfor-mance, economics, and emission reduction potential upon application of low-volatile organic compound (VOC) waterborne contact adhesive formulations specifically ina manual laminating operation for assembling s...

  17. Increased ratio of electron transport to net assimilation rate supports elevated isoprenoid emission rate in eucalypts under drought.

    Science.gov (United States)

    Dani, Kaidala Ganesha Srikanta; Jamie, Ian McLeod; Prentice, Iain Colin; Atwell, Brian James

    2014-10-01

    Plants undergoing heat and low-CO2 stresses emit large amounts of volatile isoprenoids compared with those in stress-free conditions. One hypothesis posits that the balance between reducing power availability and its use in carbon assimilation determines constitutive isoprenoid emission rates in plants and potentially even their maximum emission capacity under brief periods of stress. To test this, we used abiotic stresses to manipulate the availability of reducing power. Specifically, we examined the effects of mild to severe drought on photosynthetic electron transport rate (ETR) and net carbon assimilation rate (NAR) and the relationship between estimated energy pools and constitutive volatile isoprenoid emission rates in two species of eucalypts: Eucalyptus occidentalis (drought tolerant) and Eucalyptus camaldulensis (drought sensitive). Isoprenoid emission rates were insensitive to mild drought, and the rates increased when the decline in NAR reached a certain species-specific threshold. ETR was sustained under drought and the ETR-NAR ratio increased, driving constitutive isoprenoid emission until severe drought caused carbon limitation of the methylerythritol phosphate pathway. The estimated residual reducing power unused for carbon assimilation, based on the energetic status model, significantly correlated with constitutive isoprenoid emission rates across gradients of drought (r(2) > 0.8) and photorespiratory stress (r(2) > 0.9). Carbon availability could critically limit emission rates under severe drought and photorespiratory stresses. Under most instances of moderate abiotic stress levels, increased isoprenoid emission rates compete with photorespiration for the residual reducing power not invested in carbon assimilation. A similar mechanism also explains the individual positive effects of low-CO2, heat, and drought stresses on isoprenoid emission.

  18. Volatile organic compounds (VOCs) in surface coating materials: Their compositions and potential as an alternative fuel.

    Science.gov (United States)

    Dinh, Trieu-Vuong; Choi, In-Young; Son, Youn-Suk; Song, Kyu-Yong; Sunwoo, Young; Kim, Jo-Chun

    2016-03-01

    A sampling system was designed to determine the composition ratios of VOCs emitted from 31 surface coating materials (SCMs). Representative architectural, automotive, and marine SCMs in Korea were investigated. Toluene, ethylbenzene, and xylene were the predominant VOCs. The VOC levels (wt%) from automotive SCMs were significantly higher than those from architectural and marine paints. It was found that target SCMs comprised mainly VOCs with 6-10 carbon atoms in molecules, which could be adsorbed by activated carbon. The saturated activated carbon which had already adsorbed toluene, ethylbenzene, and m-xylene was combusted. The saturated activated carbon was more combustible than new activated carbon because it comprised inflammable VOCs. Therefore, it could be an alternative fuel when using in a "fuelization system". To use the activated carbon as a fuel, a control technology of VOCs from a coating process was also designed and introduced.

  19. Purge and trap method to determine alpha factors of VOC liquid-phase mass transfer coefficients

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    A theoretical approach and laboratory practice of determining the alpha factors of volatile organic compound (VOC) liquid-phase mass transfer coefficients are present in this study.Using Purge Trap Concentrator, VOC spiked water samples are purged by high-purity nitrogen in the laboratory, the VOC liquid-phase mass transfer rate constants under the laboratory conditions are then obtained by observing the variation of VOCs purged out of the water with the purge time.The alpha factors of VOC liquid-phase mass transfer coefficients are calculated as the ratios of the liquid-phase mass transfer rate constants in real water samples to their counterparts in pure water under the same experimental conditions. This direct and fast approach is easy to control in the laboratory, and would benefit mutual comparison among researchers, so might be useful for thestudy of VOC mass transfer across the liquid-gas interface.

  20. Evaluation of formaldehyde emission from particleboard using the large chamber and desiccator method at various loading ratios

    Institute of Scientific and Technical Information of China (English)

    QUE Ze-li; WANG Fei-bin; MA Ling-fei; Furuno Takeshi

    2013-01-01

    We studied formaldehyde emission from uncoated particleboard with 16-mm thickness using the large chamber and the desiccator method.A chamber of 28.4 m3 was installed to simulate a mobile home.The formaldehyde off-gassing properties of particleboard were evaluated using the chamber.The relationship between the concentration obtained by the chamber and the values by the desiccator test was discussed in this study under different conditions of conditioning day,air exchange,and loading ratio.These two methods were compared and discussed regarding the formaldehyde emission level.Three loading ratios,0.429 m2/m3,0.264 m2/m3,and 0.132 m2/m3,were chosen to represent different applications of particleboard products.There was strong correlation between emissions and air exchange rates at equal product-loading ratios in the large chamber,the related coefficient R2 exceeded 0.90.There was also an indication of a generic correlation between the large chamber and the two-hour desiccator test with a single product designated loading ratio,air exchange rate,and climatic conditions.

  1. 天津市O3生成与其前体物NOx、VOCs排放的相关性研究%Study of the Correlationship between O3 Generation and its Precursors NOx and VOCs E-mission in Tianjin

    Institute of Scientific and Technical Information of China (English)

    周阳; 王艳丽; 陈璐; 王伟; 张丽娜; 吉晟

    2014-01-01

    The SO2 and NOx emission data from Tianjin pollution source survey of 2010 and industrial volatile organic compounds estimation data were used as main sources to establish Tianjin air pollutant emission inventory.The meteorological fields of Tianjin Area in January,April,July,October 2010 were simulated using MM5.Finally,CMAQ model was used and several scenarios were designed to analyze the correlation ship between the O3 concentration change and NOx and VOCs emission change.The results indi-cated that O3 generation in Tianjin was limited by VOCs.O3 concentration might continue to increase when more and more NOx emis-sions were cut down,but VOCs reduction was beneficial to O3 control.In summer,more than 40% VOCs emission was needed to be cut down to avoid the O3 increase in Tianjin.%以天津市2010年污染源普查数据中 SO2、NOx及颗粒物排放数据以及各行业挥发性有机物调查核算数据为主要数据源,制作天津市大气污染物排放清单,用 MM5模型模拟2010年天津市地区1、4、7、10月的气象场,通过 CMAQ 模型,设置不同计算情景,分析天津市ρ(O3)变化与 NOx 及挥发性有机物的排放量变化关系。结果表明,天津市的 O3生成处于VOCs控制区,随着天津市 NOx减排力度的不断加大,ρ(O3)可能呈上升趋势,在夏季,需要削减40%以上挥发性有机物,以避免ρ(O3)进一步上升。

  2. Plant leaves as indoor air passive samplers for volatile organic compounds (VOCs).

    Science.gov (United States)

    Wetzel, Todd A; Doucette, William J

    2015-03-01

    Volatile organic compounds (VOCs) enter indoor environments through internal and external sources. Indoor air concentrations of VOCs vary greatly but are generally higher than outdoors. Plants have been promoted as indoor air purifiers for decades, but reports of their effectiveness differ. However, while air-purifying applications may be questionable, the waxy cuticle coating on leaves may provide a simple, cost-effective approach to sampling indoor air for VOCs. To investigate the potential use of plants as indoor air VOC samplers, a static headspace approach was used to examine the relationship between leaf and air concentrations, leaf lipid contents and octanol-air partition coefficients (Koa) for six VOCs and four plant species. The relationship between leaf and air concentrations was further examined in an actual residence after the introduction of several chlorinated VOC emission sources. Leaf-air concentration factors (LACFs), calculated from linear regressions of the laboratory headspace data, were found to increase as the solvent extractable leaf lipid content and Koa value of the VOC increased. In the studies conducted in the residence, leaf concentrations paralleled the changing air concentrations, indicating a relatively rapid air to leaf VOC exchange. Overall, the data from the laboratory and residential studies illustrate the potential for plant leaves to be used as cost effective, real-time indoor air VOC samplers.

  3. Characteristics of Ambient Volatile Organic Compounds (VOCs Measured in Shanghai, China

    Directory of Open Access Journals (Sweden)

    Guang-Qiang Zhou

    2010-08-01

    Full Text Available To better understand the characteristics of ambient abundance of volatile organic compounds (VOCs in Shanghai, one of the biggest metropolis of China, VOCs were measured with a gas chromatography system equipped with a mass-selective detector (GC/MSD from July 2006 to February 2010. An intensive measurement campaign was conducted (eight samples per day with a 3 hour interval during May 2009. The comparison of ambient VOCs collected in different regions of Shanghai shows that the concentrations are slightly higher in the busy commercial area (28.9 ppbv at Xujiaui than in the urban administrative area (24.3 ppbv at Pudong. However, during the intensive measurement period, the concentrations in the large steel industrial area (28.7 ppbv at Baoshan were much higher than in the urban administrative area (18 ppbv at Pudong, especially for alkanes, alkenes, and toluene. The seasonal variations of ambient VOC concentrations measured at the Xujiahui sampling site indicate that the VOC concentrations are significantly affected by meteorological conditions (such as wind direction and precipitation. In addition, although alkanes are the most abundant VOCs at the Xujiahui measurement site, the most important VOCs contributing to ozone formation potential (OFP are aromatics, accounting for 57% of the total OFP. The diurnal variations of VOC concentrations show that VOC concentrations are higher on weekdays than in weekends at the Xujiahui sampling site, suggesting that traffic condition and human activities have important impacts on VOC emissions in Shanghai. The evidence also shows that the major sources of isoprene are mainly resulted from gasoline evaporation at a particular time (06:00–09:00 in the busy commercial area. The results gained from this study provide useful information for better understanding the characteristics of ambient VOCs and the sources of VOCs in Shanghai.

  4. Study on the Environmental Quality Guarantee Ratio on the Basis of Total Air Pollutant Emission Amount Control

    Institute of Scientific and Technical Information of China (English)

    徐芙蓉; 施介宽

    2004-01-01

    The hourly and daily air quality concentration in the total air pollutant emission amount control zone is not sure to be continuously up to national ambient air quality standard,even though the total annual air pollutant emission is permitted under the total air pollutant emission amount control (TAPEAC) on the basis of A-value method. So the concept of the environmental quality guarantee ratio (EQGR) for TAPEAC is advanced in this paper and its quantitative formula is figured out for both hourly and daily EQGR. It is concluded that the EQGR is related with the yearly arrangement of A-value besides the pollutant type.According to the meteorological data in a lower area along Yangtze River in 2000, the yearly A-value trend is analyzed. Based on the data, the hourly EQGR of SO2 and NO2 is respectively 97.4% and 90.2%, and daily EQGR respectively 90.2% and 79.5%.

  5. The field emission properties of high aspect ratio diamond nanocone arrays fabricated by focused ion beam milling

    Directory of Open Access Journals (Sweden)

    Z.L. Wang, Q. Wang, H.J. Li, J.J. Li, P. Xu, Q. Luo, A.Z. Jin, H.F. Yang and C.Z. Gu

    2005-01-01

    Full Text Available High aspect ratio diamond nanocone arrays are formed on freestanding diamond film by means of focused ion beam (FIB milling technology and hot-filament chemical vapor deposition (HFCVD method. The structure and phase purity of an individual diamond nanocone are characterized by scanning electron microscopy (SEM and micro-Raman spectroscopy. The result indicates that the diamond cones with high aspect ratio and small tip apex radius can be obtained by optimizing the parameters of FIB milling and diamond growth. The diamond nanocone arrays were also used to study the electron field emission properties and electric field shielding effect, finding high emission current density, low threshold and weak shielding effect, all attributable to the high field enhancement factor and suitable cone density of the diamond nanocone emitter

  6. Constant-Pressure Specific Heat to Hemispherical Total Emissivity Ratio for Undercooled Liquid Nickel, Zirconium, and Silicon

    Science.gov (United States)

    Rulison, Aaron J.; Rhim, Won-Kyu

    1995-01-01

    Radiative cooling curves of nickel, zirconium, and silicon melts that were obtained using the high-temperature, high-vacuum electrostatic levitator (HTHVESL) have been analyzed to determine the ratio between the constant-pressure specific heat and the hemispherical total emissivity, c(sub p)(T)epsilon(sub T)(T). This ratio determined over a wide liquid temperature range for each material allows us to determine c(sub p)(T) if epsilon(sub T)(T) is known or vice versa. Following the recipe, the hemi-spherical total emissivities for each sample at its melting temperature, epsilon(sub T)(T(sub M)), have been determined using c(sub p)(T(sub m)) values available in the literature. They are 0.15, 0.29, and 0.17, for Ni, Zr, and Si, respectively.

  7. Total OH reactivity study from VOC photochemical oxidation in the SAPHIR chamber

    Science.gov (United States)

    Yu, Z.; Tillmann, R.; Hohaus, T.; Fuchs, H.; Novelli, A.; Wegener, R.; Kaminski, M.; Schmitt, S. H.; Wahner, A.; Kiendler-Scharr, A.

    2015-12-01

    It is well known that hydroxyl radicals (OH) act as a dominant reactive species in the degradation of VOCs in the atmosphere. In recent field studies, directly measured total OH reactivity often showed poor agreement with OH reactivity calculated from VOC measurements (e.g. Nölscher et al., 2013; Lu et al., 2012a). This "missing OH reactivity" is attributed to unaccounted biogenic VOC emissions and/or oxidation products. The comparison of total OH reactivity being directly measured and calculated from single component measurements of VOCs and their oxidation products gives us a further understanding on the source of unmeasured reactive species in the atmosphere. This allows also the determination of the magnitude of the contribution of primary VOC emissions and their oxidation products to the missing OH reactivity. A series of experiments was carried out in the atmosphere simulation chamber SAPHIR in Jülich, Germany, to explore in detail the photochemical degradation of VOCs (isoprene, ß-pinene, limonene, and D6-benzene) by OH. The total OH reactivity was determined from the measurement of VOCs and their oxidation products by a Proton Transfer Reaction Time of Flight Mass Spectrometer (PTR-TOF-MS) with a GC/MS/FID system, and directly measured by a laser-induced fluorescence (LIF) at the same time. The comparison between these two total OH reactivity measurements showed an increase of missing OH reactivity in the presence of oxidation products of VOCs, indicating a strong contribution to missing OH reactivity from uncharacterized oxidation products.

  8. Volcanic SO2 and SiF4 visualization and their ratio monitored using 2-D thermal emission spectroscopy

    Science.gov (United States)

    Stremme, W.; Krueger, A.; Harig, R.; Grutter, M.

    2011-09-01

    The composition and emission rates of volcanic gas plumes provide insight of the geologic internal activity, atmospheric chemistry, aerosol formation and radiative processes around it. Observations are necessary for public security and the aviation industry. Ground-based thermal emission infrared spectroscopy, which uses the radiation of the volcanic gas itself, allows for continuously monitoring during day and night from a save distance. We present measurements on Popocatépetl volcano based on thermal emission spectroscopy during different campaigns between 2006-2009 using a Scanning Infrared Gas Imaging System (SIGIS). The experimental set-up, measurement geometries and analytical algorithms are described. The equipment was operated from a safe distance of 12 km from the volcano at two different spectral resolutions: 0.5 and 4 cm-1. The 2-dimensional scanning capability of the instrument allows for an on-line visualization of the volcanic SO2 plume, animation and determination of its propagation speed. SiF4 was also identified in the infrared spectra recorded at both resolutions. The SiF4/SO2 molecular ratio can be calculated from each image and used as a highly useful parameter to follow changes in volcanic activity. A small Vulcanian eruption was monitored during the night of 16 to 17 November 2008 which was confirmed from the strong ash emission registered around 01:00 a.m. LST (Local Standard Time) and a pronounced SO2 cloud was registered. Enhanced SiF4/SO2 ratios were observed before and after the eruption. A validation of the results from thermal emission measurements with those from absorption spectra of the moon taken at the same time, as well as an error analysis, are presented. The inferred propagation speed from sequential imagees is used to calculate the emission rates at different distances from the crater.

  9. Combustion and Emission Characteristics of Variable Compression Ignition Engine Fueled with Jatropha curcas Ethyl Ester Blends at Different Compression Ratio

    Directory of Open Access Journals (Sweden)

    Rajneesh Kumar

    2014-01-01

    Full Text Available Engine performance and emission characteristics of unmodified biodiesel fueled diesel engines are highly influenced by their ignition and combustion behavior. In this study, emission and combustion characteristics were studied when the engine operated using the different blends (B10, B20, B30, and B40 and normal diesel fuel (B0 as well as when varying the compression ratio from 16.5 : 1 to 17.5 : 1 to 18.5 : 1. The change of compression ratio from 16.5 : 1 to 18.5 : 1 resulted in 27.1%, 27.29%, 26.38%, 28.48%, and 34.68% increase in cylinder pressure for the blends B0, B10, B20, B30, and B40, respectively, at 75% of rated load conditions. Higher peak heat release rate increased by 23.19%, 14.03%, 26.32%, 21.87%, and 25.53% for the blends B0, B10, B20, B30, and B40, respectively, at 75% of rated load conditions, when compression ratio was increased from16.5 : 1 to 18.5 : 1. The delay period decreased by 21.26%, CO emission reduced by 14.28%, and NOx emission increased by 22.84% for B40 blends at 75% of rated load conditions, when compression ratio was increased from 16.5 : 1 to 18.5 : 1. It is concluded that Jatropha oil ester can be used as fuel in diesel engine by blending it with diesel fuel.

  10. Stimulus Ratio and Level Dependence of Low- and Mid-Frequency Distortion-Product Otoacoustic Emissions

    DEFF Research Database (Denmark)

    Christensen, Anders Tornvig; Ordoñez, Rodrigo Pizarro; Hammershøi, Dorte

    2014-01-01

    Active amplifiers within the cochlea generate, as a by-product of their function, distortion-product otoacoustic emissions (DPOAEs) in response to carefully chosen two-tone stimuli. Focus has been on invoking emissions in a mid-frequency range from 500 to 4000 Hz. Below 500 Hz, physiological noise...... audiometrically normal hearing for inclusion in our experiment. DPOAEs were measured with pure-tone stimuli in four configurations: f2 fixed around a mid-frequency (2050-2180 Hz), f2 fixed around a low frequency (512-545 Hz), fdp fixed at a mid-frequency (1231 Hz) and fdp low frequency (246 Hz). Eight stimulus...

  11. Emission characteristics of volatile organic compounds from coal-, coal gangue-, and biomass-fired power plants in China

    Science.gov (United States)

    Yan, Yulong; Yang, Chao; Peng, Lin; Li, Rumei; Bai, Huiling

    2016-10-01

    Face the large electricity demand, thermal power generation still derives the main way of electricity supply in China, account for 78.19% of total electricity production in 2013. Three types of thermal power plants, including coal-fired power plant, coal gangue-fired power plant and biomass-fired power plant, were chosen to survey the source profile, chemical reactivity and emission factor of VOCs during the thermal power generation. The most abundant compounds generated during coal- and coal gangue-fired power generation were 1-Butene, Styrene, n-Hexane and Ethylene, while biomass-fired power generation were Propene, 1-Butenen, Ethyne and Ethylene. The ratios of B/T during thermal power generation in this study was 0.8-2.6, which could be consider as the characteristics of coal and biomass burning. The field tested VOCs emission factor from coal-, coal gangue- and biomass-fired power plant was determined to be 0.88, 0.38 and 3.49 g/GJ, or showed as 0.023, 0.005 and 0.057 g/kg, with the amount of VOCs emission was 44.07, 0.08, 0.45 Gg in 2013, respectively. The statistical results of previous emission inventory, which calculated the VOCs emission used previous emission factor, may overestimate the emission amount of VOCs from thermal power generation in China.

  12. Concentrations and fluxes of isoprene and oxygenated VOCs at a French Mediterranean oak forest

    Directory of Open Access Journals (Sweden)

    C. Kalogridis

    2014-01-01

    Full Text Available The CANOPEE project aims to better understand the biosphere-atmosphere exchanges of biogenic volatile organic compounds (BVOC in the case of Mediterranean ecosystems and the impact of in-canopy processes on the atmospheric chemical composition above the canopy. Based on an intensive field campaign, the objective of our work was to determine the chemical composition of the air inside a canopy as well as the net fluxes of reactive species between the canopy and the boundary layer. Measurements were carried out during spring 2012 at the Oak Observatory of the Observatoire de Haute Provence (O3HP located in the southeast of France. The field site presents one dominant tree species, Quercus pubescens L., a typical Mediterranean species which features large isoprene emission rates. Mixing ratios of isoprene, its degradation products methylvinylketone (MVK and methacrolein (MACR and several other oxygenated VOC (OxVOC were measured above the canopy using an online proton transfer reaction mass spectrometer (PTR-MS, and fluxes were calculated by the disjunct eddy covariance approach. The O3HP site was found to be a very significant source of isoprene emissions, with daily maximum ambient concentrations ranging between 2–16 ppbv inside and 2–5 ppbv just above the top of the forest canopy. Significant isoprene fluxes were observed only during daytime, following diurnal cycles with midday net emission fluxes from the canopy ranging between 2–8 mg m−2 h1. Net isoprene normalised flux (at 30 °C, 1000 μmol m−2 s−1 was estimated at 6.6 mg m−2 h−1. The (MVK+MACR-to-isoprene ratio was used to assess the degree of isoprene oxidation. In-canopy chemical oxidation of isoprene was found to be weak, as indicated by the low (MVK+MACR-to-isoprene ratio (~ 0.13 and low MVK+MACR fluxes, and did not seem to have a significant impact on isoprene concentrations and fluxes above the canopy. Evidence of direct emission of methanol was also found exhibiting

  13. Development of net energy ratio and emission factor for quad-generation pathways

    DEFF Research Database (Denmark)

    Rudra, Souman; Rosendahl, Lasse; Kumar, Amit

    2014-01-01

    of this study was to evaluate the energy performance, reduce GHG and acid rain precursor emission, and use of biomass for different outputs based on demand. Finally, a sensitivity analysis and a comparative study ar conducted for expected technological improvements and factors that could increase the energy...

  14. Aspect ratio tuned red-shift of photoluminescence emission of PbSe nanorods investigated by electron holography.

    Science.gov (United States)

    Li, Ying; Du, Haifeng; Zhang, Jie; Liu, Zhengwang; Tian, Mingliang; Che, Renchao

    2017-05-01

    The physical properties of nanometer scale semiconductors are known to be sensitively influenced by their aspect ratios, but the intrinsic mechanisms still remain unclear. Shape-controlled anisotropic PbSe nanorods were obtained by means of the addition of MnCl2, and the aspect ratio of the nanorods can be continuously tuned from 1 to 10 by simply modulating the amount of chloride ions. It was demonstrated that an optimized concentration of Cl(-) anions is about 0.04mmol, which controls the competition between thermodynamics and kinetics mechanisms. The emission peaks of the infrared absorbance and photoluminescence spectra were significantly tuned from 1664nm to 1840nm and from 1459nm to 1938nm only by the aspect ratios, respectively. A strong electric dipole phenomenon localized onside the surface of PbSe nanorods terminated by Pb(2+) charge was found by using high-spatial-resolution off-axis electron holography, which was furthermore evidenced by the quantitative analysis of the mean inner potential and the surfaces charge. The charge intensity depended on the aspect ratio of PbSe nanorods. The results provide clear evidence that the energy gap interval reduces as a result of the increasing of conduction charge amounts. A novel strategy to facilely shift the peak position of absorbance and photoluminescence emission was therefore proposed. Copyright © 2017. Published by Elsevier Inc.

  15. Performance and emission of generator Diesel engine using methyl esters of palm oil and diesel blends at different compression ratio

    Science.gov (United States)

    Aldhaidhawi, M.; Chiriac, R.; Bădescu, V.; Pop, H.; Apostol, V.; Dobrovicescu, A.; Prisecaru, M.; Alfaryjat, A. A.; Ghilvacs, M.; Alexandru, A.

    2016-08-01

    This study proposes engine model to predicate the performance and exhaust gas emissions of a single cylinder four stroke direct injection engine which was fuelled with diesel and palm oil methyl ester of B7 (blends 7% palm oil methyl ester with 93% diesel by volume) and B10. The experiment was conducted at constant engine speed of 3000 rpm and different engine loads operations with compression ratios of 18:1, 20:1 and 22:1. The influence of the compression ratio and fuel typeson specific fuel consumption and brake thermal efficiency has been investigated and presented. The optimum compression ratio which yields better performance has been identified. The result from the present work confirms that biodiesel resulting from palm oil methyl ester could represent a superior alternative to diesel fuel when the engine operates with variable compression ratios. The blends, when used as fuel, result in a reduction of the brake specific fuel consumption and brake thermal efficiency, while NOx emissions was increased when the engine is operated with biodiesel blends.

  16. A Tight Relation Between N/O Ratio and Galaxy Stellar Mass Can Explain the Evolution of Strong Emission Line Ratios with Redshift

    CERN Document Server

    Masters, Daniel; Capak, Peter

    2016-01-01

    The offset of high redshift star-forming galaxies in the [OIII]/H$\\beta$ versus [NII]/H$\\alpha$ (O3N2) diagram in comparison with the local star-forming galaxy sequence is now well established. The physical origin of the shift is the subject of some debate, and has important implications for metallicity measurements based on strong lines at all redshifts. To investigate the origin of the O3N2 offset, we use a sample of ~100,000 star-forming galaxies from SDSS DR12 to probe the empirical correlations between emission line diagnostics and measurable galaxy physical properties. In particular, we examine how surface density of star formation, ionization parameter, nitrogen-to-oxygen (N/O) ratio, and stellar mass drive position in two key diagnostic diagrams: O3N2 and [OIII]/H$\\beta$ versus [SII]/H$\\alpha$ (O3S2). We show that, at fixed [OIII]/H$\\beta$, galaxies falling closer to the high-redshift locus in O3N2 have higher star formation density, stellar mass and N/O ratios. We also find a tight correspondence in ...

  17. Interplay of dust alignment, grain growth, and magnetic fields in polarization: lessons from the emission-to-extinction ratio

    Science.gov (United States)

    Fanciullo, L.; Guillet, V.; Boulanger, F.; Jones, A. P.

    2017-06-01

    Context. Polarized extinction and emission from dust in the interstellar medium (ISM) are hard to interpret, as their dependence on dust optical properties, grain alignment, and magnetic field orientation is complex. This is particularly true in molecular clouds. The aforementioned phenomena are usually considered independently in polarization studies, while it is likely that they all contribute and their effects have yet to be disentangled. Aims: The data available today are not yet used to their full potential. The combination of emission and extinction, in particular, provides information not available from either of them alone. We combine data from the scientific literature on polarized dust extinction with Planck data on polarized emission, and we use them to constrain the possible variations in dust and environmental conditions inside molecular clouds, and especially translucent lines of sight, taking the magnetic field orientation into account. Methods: We focused on the dependence between λmax (the wavelength of maximum polarization in extinction) and other observables such as the extinction polarization, the emission polarization, and the ratio between the two. We set out to reproduce these correlations using Monte Carlo simulations in which we varied the relevant quantities in a dust model, which are grain alignment, size distribution, and magnetic field orientation, to mimic the diverse conditions that are expected inside molecular clouds. Results: None of the quantities we chose can explain the observational data on their own: the best results are obtained when all quantities vary significantly across and within clouds. However, some of the data, most notably the stars with a low ratio of polarization in emission to polarization in extinction, are not reproduced by our simulation. Conclusions: Our results suggest not only that dust evolution is necessary to explain polarization in molecular clouds, but that a simple change in size distribution is not

  18. Ultra High Bypass Ratio Engine Research for Reducing Noise, Emissions, and Fuel Consumption

    Science.gov (United States)

    Hughes, Christopher E.; Schweitzer, Jeff

    2007-01-01

    A pictorial history of NASA development of advanced engine technologies for reducing environmental emissions and increasing performance from the 1970s to 2000s is presented. The goals of the Subsonic Fixed Wing Program portion of the NASA Fundamental Aeronautics Program are discussed, along with the areas of investigation currently being pursued by the Ultra High Bypass Partnership Element of the Subsonic Fixed Wing Program.

  19. The probability distribution functions of emission line flux measurements and their ratios

    CERN Document Server

    Wesson, R; Scicluna, P

    2016-01-01

    Many physical parameters in astrophysics are derived using the ratios of two observed quantities. If the relative uncertainties on measurements are small enough, uncertainties can be propagated analytically using simplifying assumptions, but for large normally distributed uncertainties, the probability distribution of the ratio become skewed, with a modal value offset from that expected in Gaussian uncertainty propagation. Furthermore, the most likely value of a ratio A/B is not equal to the reciprocal of the most likely value of B/A. The effect is most pronounced when the uncertainty on the denominator is larger than that on the numerator. We show that this effect is seen in an analysis of 12,126 spectra from the Sloan Digital Sky Survey. The intrinsically fixed ratio of the [O III] lines at 4959 and 5007 ${\\AA}$ is conventionally expressed as the ratio of the stronger line to the weaker line. Thus, the uncertainty on the denominator is larger, and non-Gaussian probability distributions result. By taking thi...

  20. Assessment of Volatile Organic Compounds (VOCs) in indooor parking facilities at Houston, Texas

    Science.gov (United States)

    Kristanto, Gabriel Andari

    This dissertation identified the types, magnitudes, sources, and assessed risk exposure of VOCs in different types of indoor parking facilities. VOCs are ones of major pollutants emitted from automobiles. The indoor parking facilities included were attached garages, grounds, and underground parking. Modification of method TO15 by EPA had been applied for identifying types and magnitudes of VOCs. Results of these identifications are presented. Eight most abundant VOCs could be identified in every sampling location with toluene as the most abundant compound followed by m,p-xylene, ethylbenzene and benzene. Compare to ground and underground parking, attached garages have the highest concentration of TVOCs. For sources identification, BTEX, m,p-xylene and benzene, and toluene and benzene ratios are calculated. BTEX ratios for ground and underground parking are similar compare to attached garage due to the similar pattern of driving speed and the content of gasoline fuel. On the other hand the ratios of m,p-xylene and benzene and toluene and benzene in attached garage are higher compare to the same ratios for ground and underground parking due to other significant contributor of VOCs such as solvent, household cleanings stored. Cancer and noncancer risk assessment were also calculated. Results showed that cancer and noncancer risk due human exposures to VOC in indoor parking facilities were relatively low. However the risk of the human exposure to VOCs from indoor parking facilities has to be considered as a part of total risks of VOC exposures on human during their daily activities. When people in Houston have already exposed to high VOC concentrations from outdoor environment activities such as traffic and refineries and petrochemical facilities, additional activities causing VOC exposures will add the risk significantly.

  1. Effects of feed restriction and forage:concentrate ratio on digestibility, methane emission, and energy utilization by goats

    Directory of Open Access Journals (Sweden)

    Ana Rebeca Castro Lima

    Full Text Available ABSTRACT This study was carried out to to evaluate how feed restriction and different forage:concentrate ratios affect digestibility, methane emission (using the SF6 technique, and energy utilization of Anglo-Nubian goats. Fifteen (15 dry and non-pregnant Anglo Nubian goats, averaging 30±2.9 kg body weight, were used. The experiment was divided into two trials, the first of which was designed to study the effects of feed restriction (0% or ad libitum; 15% of feed restriction or equivalent to 85% of ad libitum intake; and 40% of feed restriction or equivalent to 60% of ad libitum intake and the second, to study the effects of forage:concentrate (F:C ratios (75:25, 54:46, and 25:75 in the diet. The sulfur hexafluoride (SF6 tracer gas method was used to collect and estimate methane (CH4 emissions. Feed restriction level did not affect apparent total tract digestibility of dry matter (DM, organic matter, crude protein, and neutral detergent fiber. Methane emission (g d−1 decreased linearly as intake level decreased. However, energy loss in methane proportional to organic matter intake was similar among levels of feed restriction; consequently, dietary metabolizability did not differ among treatments. Methane gas (g d−1 as a function of F:C ratio revealed a quadratic response, showing the highest values when animals were fed the 46:54 F:C ratio diet (18.2 g d−1, suggesting that the decrease in absolute CH4 occurred when the level of concentrate inclusion in the diet surpassed approximately 50%. The results presented herein may be relevant for the ongoing and future efforts towards completion of an IPCC inventory regarding the contribution of goats to the greenhouse gas effects on the planet.

  2. Reassessing the ratio of glyoxal to formaldehyde as an indicator of hydrocarbon precursor speciation

    Directory of Open Access Journals (Sweden)

    J. Kaiser

    2015-03-01

    Full Text Available The yield of formaldehyde (HCHO and glyoxal (CHOCHO from oxidation of volatile organic compounds (VOCs depends on precursor VOC structure and the concentration of NOx (NOx = NO +NO2. Previous work has proposed that the ratio of CHOCHO to HCHO (RGF can be used as an indicator of precursor VOC speciation, and absolute concentrations of the oxidation products as indicators of NOx. Because this metric is measurable by satellite, it is potentially useful on a global scale; however, absolute values and trends in RGF have differed between satellite and ground-based observations. To investigate potential causes of previous discrepancies and the usefulness of this ratio, we present measurements of CHOCHO and HCHO over the Southeast United States (SE US from the 2013 SENEX flight campaign and compare these measurements with OMI satellite retrievals. High time-resolution flight measurements show that high RGF is associated with monoterpene emissions, low RGF is associated with isoprene oxidation, and emissions associated with oil and gas production can lead to small-scale variation in regional RGF. During the summertime in the SE US, RGF is not a reliable diagnostic of anthropogenic VOC emissions, as HCHO and CHOCHO production are dominated by isoprene oxidation. Our results show that the new glyoxal retrieval algorithm reduces the previous disagreement between satellite and in situ RGF observations. We conclude that satellite-based observations of RGF can be used alongside other measurements as a global diagnostic of the chemical conditions leading to secondary pollutant formation.

  3. A new method for convenient and quick determination of the mass transfer characteristics of VOC emission from the wood furniture%木家具挥发性污染物散发传质特性测定新方法

    Institute of Scientific and Technical Information of China (English)

    宋伟; 孔庆媛; 李洪枚

    2013-01-01

    The paper is aimed at introducing a new method for convenient and quick determination of the mass transfer characteristics of the volatile organic compounds(VOC) from the wood furniture. As is known, VOC emission is one of such emissions, which involves a complex process of mass transfer with negative environmental effects. For our research convenience, we have worked out a clear outline to show the mass transfer characteristics and brought forward an experimental method for convenient, quick and simultaneous measurement of the four significant mass transfer parameters of the target VOC: the emission concentration ρ0, the diffusion coefficient D, the partition coefficient K and the convection mass transfer coefficient hm by making use of the mass transfer equilibrium or process concentrations in a chamber with no proper ventilation under a series of loading factors Lf. Detailedly speaking, we have established a method for analyzing a fully analytical model of furniture emission in the chamber without proper ventilation deduced by Laplace Transform. On the one hand, a linear relationship can be found and represented between the reciprocal of equilibrium concentrations and the reciprocal of Lf, whose slope and intercept are the simple function of ρ0 and K. By data fitting, we could easily obtain the slope and intercept as well as ρ0 and K. On the other hand, a linear relationship can also be expressed by the relationship between the logarithm of dimensionless excess concentrations and the time elapsed, with the slope and intercept being the simple function of D and hm. By data fitting, it would be possible to deduce the slope and intercept as well as D and hm very simply, too. In addition, in the experiments we have done, we have applied this method to study ρ0, D, K, hm of formaldehyde and TVOC mass transfer from a piece of wood furniture made of medium density fiberboards(MDF) and polyurethane paint (PU) . The results of our experiments show a coefficient of

  4. Effect of digestibility of grass-clover silage and concentrate to forage ratio on methane emission from dairy cows

    DEFF Research Database (Denmark)

    Hellwing, Anne Louise Frydendahl; Weisbjerg, Martin Riis

    and D, respectively. TMR forage DM consisted of 2/3 of one of the respective grass-clover silages and 1/3 maize silage, and concentrate (soya meal and wheat) proportion of DM was 20% (low) or 50% (high). Methane emissions from the cows were measured 20-22 hours in one of four chambers working after......That methane emission from dairy cows is affected by concentrate to forage ratio is well known, whereas the effect of the quality of grass-clover silage is not well described. Besides this the purpose of the present study also was to test our new facilities for measuring methane emission from dairy...... cows and the working routines. Twenty-four Holstein cows were allocated to eight different treatments and blocked according to parity. Treatments were in a 2x4 design, 2 concentrate to forage ratios and four different grass-clover silages. The grass-clover silages (A, B, C, D) were produced during...

  5. Volatile organic compound emissions from unconventional natural gas production: Source signatures and air quality impacts

    Science.gov (United States)

    Swarthout, Robert F.

    Advances in horizontal drilling and hydraulic fracturing over the past two decades have allowed access to previously unrecoverable reservoirs of natural gas and led to an increase in natural gas production. Intensive unconventional natural gas extraction has led to concerns about impacts on air quality. Unconventional natural gas production has the potential to emit vast quantities of volatile organic compounds (VOCs) into the atmosphere. Many VOCs can be toxic, can produce ground-level ozone or secondary organic aerosols, and can impact climate. This dissertation presents the results of experiments designed to validate VOC measurement techniques, to quantify VOC emission rates from natural gas sources, to identify source signatures specific to natural gas emissions, and to quantify the impacts of these emissions on potential ozone formation and human health. Measurement campaigns were conducted in two natural gas production regions: the Denver-Julesburg Basin in northeast Colorado and the Marcellus Shale region surrounding Pittsburgh, Pennsylvania. An informal measurement intercomparison validated the canister sampling methodology used throughout this dissertation for the measurement of oxygenated VOCs. Mixing ratios of many VOCs measured during both campaigns were similar to or higher than those observed in polluted cities. Fluxes of natural gas-associated VOCs in Colorado ranged from 1.5-3 times industry estimates. Similar emission ratios relative to propane were observed for C2-C6 alkanes in both regions, and an isopentane:n-pentane ratio ≈1 was identified as a unique tracer for natural gas emissions. Source apportionment estimates indicated that natural gas emissions were responsible for the majority of C2-C8 alkanes observed in each region, but accounted for a small proportion of alkenes and aromatic compounds. Natural gas emissions in both regions accounted for approximately 20% of hydroxyl radical reactivity, which could hinder federal ozone standard

  6. Concentration, ozone formation potential and source analysis of volatile organic compounds (VOCs) in a thermal power station centralized area: A study in Shuozhou, China.

    Science.gov (United States)

    Yan, Yulong; Peng, Lin; Li, Rumei; Li, Yinghui; Li, Lijuan; Bai, Huiling

    2017-04-01

    Volatile organic compounds (VOCs) from two sampling sites (HB and XB) in a power station centralized area, in Shuozhou city, China, were sampled by stainless steel canisters and measured by gas chromatography-mass selective detection/flame ionization detection (GC-MSD/FID) in the spring and autumn of 2014. The concentration of VOCs was higher in the autumn (HB, 96.87 μg/m(3); XB, 58.94 μg/m(3)) than in the spring (HB, 41.49 μg/m(3); XB, 43.46 μg/m(3)), as lower wind speed in the autumn could lead to pollutant accumulation, especially at HB, which is a new urban area surrounded by residential areas and a transportation hub. Alkanes were the dominant group at both HB and XB in both sampling periods, but the contribution of aromatic pollutants at HB in the autumn was much higher than that of the other alkanes (11.16-19.55%). Compared to other cities, BTEX pollution in Shuozhou was among the lowest levels in the world. Because of the high levels of aromatic pollutants, the ozone formation potential increased significantly at HB in the autumn. Using the ratio analyses to identify the age of the air masses and analyze the sources, the results showed that the atmospheric VOCs at XB were strongly influenced by the remote sources of coal combustion, while at HB in the spring and autumn were affected by the remote sources of coal combustion and local sources of vehicle emission, respectively. Source analysis conducted using the Positive Matrix Factorization (PMF) model at Shuozhou showed that coal combustion and vehicle emissions made the two largest contributions (29.98% and 21.25%, respectively) to atmospheric VOCs. With further economic restructuring, the influence of vehicle emissions on the air quality should become more significant, indicating that controlling vehicle emissions is key to reducing the air pollution.

  7. Low VOC drying of lumber and wood panel products. Progress report No. 4, annual summary

    Energy Technology Data Exchange (ETDEWEB)

    Boerner, J.; Su, Wei; Yan, Hui [and others

    1997-07-01

    Heating softwood in a low-headspace environment draws out the VOCs from the wood, without removing the water. The VOCs can be collected from the headspace, and represent a valuable product. The VOC-depleted wood can then be dried conventionally with much reduced emissions. Heating can be accomplished through radiofrequency (RF) or steam. For lumber, steam is inefficient, but brief RF treatment under low-headspace conditions draws out 80% of the VOCs. The power used is quite low, since the RF energy is not used to remove water, but only to maintain the wood at a set temperature. The technology is now at the pre-pilot stage. Either steam or RF can be used for particle, OSB, and veneer, again under low-headspace conditions. Increasing steam temperature facilitates VOC removal. In order to understand the mechanism of VOC release in lumber, the transport of water and VOCs to the surface is being studied as a function of sample size and orientation. Characterization of the terpenes and resin/fatty acids from a control set of trees is underway in order to define the seasonal influence on VOCs.

  8. Observations of volatile organic compounds during ARCTAS – Part 1: Biomass burning emissions and plume enhancements

    Directory of Open Access Journals (Sweden)

    A. Hills

    2011-05-01

    Full Text Available Mixing ratios of a large number of volatile organic compounds (VOCs were observed by the Trace Organic Gas Analyzer (TOGA on board the NASA DC-8 as part of the Arctic Research of the Composition of the Troposphere from Aircraft and Satellites (ARCTAS field campaign. Many of these VOCs were observed concurrently by one or both of two other VOC measurement techniques on board the DC-8: proton-transfer-reaction mass spectrometry (PTR-MS and whole air canister sampling (WAS. A comparison of these measurements to the data from TOGA indicates good agreement for the majority of co-measured VOCs. The ARCTAS study, which included both spring and summer deployments, provided opportunities to sample a large number of biomass burning (BB plumes with origins in Asia, California and Central Canada, ranging from very recent emissions to plumes aged one week or more. For this analysis, identified BB plumes were grouped by flight, source region and, in some cases, time of day, generating 40 individual plume groups, each consisting of one or more BB plume interceptions. Normalized excess mixing ratios (EMRs to CO were determined for each of the 40 plume groups for up to 19 different VOCs or VOC groups, many of which show significant variability, even within relatively fresh plumes. This variability demonstrates the importance of assessing BB plumes both regionally and temporally, as emissions can vary from region to region, and even within a fire over time. Comparisons with literature confirm that variability of EMRs to CO over an order of magnitude for many VOCs is consistent with previous observations. However, this variability is often diluted in the literature when individual observations are averaged to generate an overall regional EMR from a particular study. Previous studies give the impression that emission ratios are generally consistent within a given region, and this is not necessarily the case, as our results show. For some VOCs, earlier assumptions

  9. Influence of oil and gas emissions on summertime ozone in the Colorado Northern Front Range

    Science.gov (United States)

    McDuffie, Erin E.; Edwards, Peter M.; Gilman, Jessica B.; Lerner, Brian M.; Dubé, William P.; Trainer, Michael; Wolfe, Daniel E.; Angevine, Wayne M.; deGouw, Joost; Williams, Eric J.; Tevlin, Alex G.; Murphy, Jennifer G.; Fischer, Emily V.; McKeen, Stuart; Ryerson, Thomas B.; Peischl, Jeff; Holloway, John S.; Aikin, Kenneth; Langford, Andrew O.; Senff, Christoph J.; Alvarez, Raul J.; Hall, Samuel R.; Ullmann, Kirk; Lantz, Kathy O.; Brown, Steven S.

    2016-07-01

    Tropospheric O3 has been decreasing across much of the eastern U.S. but has remained steady or even increased in some western regions. Recent increases in VOC and NOx emissions associated with the production of oil and natural gas (O&NG) may contribute to this trend in some areas. The Northern Front Range of Colorado has regularly exceeded O3 air quality standards during summertime in recent years. This region has VOC emissions from a rapidly developing O&NG basin and low concentrations of biogenic VOC in close proximity to urban-Denver NOx emissions. Here VOC OH reactivity (OHR), O3 production efficiency (OPE), and an observationally constrained box model are used to quantify the influence of O&NG emissions on regional summertime O3 production. Analyses are based on measurements acquired over two summers at a central location within the Northern Front Range that lies between major regional O&NG and urban emission sectors. Observational analyses suggest that mixing obscures any OPE differences in air primarily influenced by O&NG or urban emission sector. The box model confirms relatively modest OPE differences that are within the uncertainties of the field observations. Box model results also indicate that maximum O3 at the measurement location is sensitive to changes in NOx mixing ratio but also responsive to O&NG VOC reductions. Combined, these analyses show that O&NG alkanes contribute over 80% to the observed carbon mixing ratio, roughly 50% to the regional VOC OHR, and approximately 20% to regional photochemical O3 production.

  10. The extended narrow line region of NGC 4151. I - Emission line ratios and their implications

    Science.gov (United States)

    Penston, M. V.; Robinson, A.; Alloin, D.; Appenzeller, I.; Aretxaga, I.; Axon, D. J.; Baribaud, T.; Barthel, P.; Baum, S. A.; Boisson, C.; de Bruyn, A. G.; Clavel, J.; Colina, L.; Dennefeld, M.; Diaz, A.; Dietrich, M.; Durret, F.; Dyson, J. E.; Gondhalekar, P.; van Groningen, E.; Jablonka, P.; Jackson, N.; Kollatschny, W.; Laurikainen, E.; Lawrence, A.; Masegosa, J.; McHardy, I.; Meurs, E. J. A.; Miley, G.; Moles, M.; O'Brien, P.; O'Dea, C.; del Olmo, A.; Pedlar, A.; Perea, J.; Perez, E.; Perez-Fournon, I.; Perry, J.; Pilbratt, G.; Rees, M.; Robson, I.; Rodriguez-Pascual, P.; Rodriguez Espinosa, J. M.; Santos-Lleo, M.; Schilizzi, R.; Stasińska, G.; Stirpe, G. M.; Tadhunter, C.; Terlevich, E.; Terlevich, R.; Unger, S.; Vila-Vilaro, V.; Vilchez, J.; Wagner, S. J.; Ward, M. J.; Yates, G. J.

    1990-09-01

    The paper presents the first results from long-slit spectra of the Seyfert galaxy NGC 4151 which give average diagnostic ratios of weak lines in the Extended Narrow Line Region (ENLR) of the galaxy and the first direct density measurement in an ENLR. These data confirm that the ENLR is kinematically undisturbed gas in the disk of the galaxy which is illuminated by an ionizing continuum stronger by a factor of 13 than a power law interpolated between recently observed ultraviolet and X-ray fluxes. Explanations of this apparent excess include a hot thermal continuum, time variations, and an anisotropic rotation field.

  11. Emission of volatile organic compounds from solid waste disposal sites and importance of heat management.

    Science.gov (United States)

    Urase, Taro; Okumura, Hiroyuki; Panyosaranya, Samerjai; Inamura, Akihiro

    2008-12-01

    The emission of volatile organic compounds (VOCs) from a solid waste disposal site for municipal solid wastes was quantified. The VOCs contained in the landfill gas taken at the site were benzene, toluene, xylenes, ethyl benzenes, and trimethyl benzenes, while the concentrations of chlorinated compounds were very low. The concentration of benzene in the landfill gas samples ranged from below the detection limit to 20 mg m(-3), and the ratio of benzene to toluene ranged from 0.2 to 8. The higher concentrations of VOCs in landfill gas and in leachates were observed with the samples taken at high temperature areas of the target site. Polystyrene plastic waste was identified as one of the sources of VOCs in solid waste disposal sites at a high temperature condition. The appropriate heat management in landfill sites is an important countermeasure to avoid unusually high emission of VOCs because the heat generated by the biodegradation of organic solid wastes may promote the release of VOCs, especially in the case of sites which receive both biodegradable and plastic wastes.

  12. Shocked POststarbust Galaxy Survey I: Candidate Poststarbust Galaxies with Emission Line Ratios Consistent with Shocks

    CERN Document Server

    Alatalo, Katherine; Rich, Jeffrey A; Appleton, Philip N; Kewley, Lisa J; Lacy, Mark; Lanz, Lauranne; Medling, Anne M; Nyland, Kristina

    2016-01-01

    [Abridged] There are many mechanisms by which galaxies can transform from blue, star-forming spirals to red, quiescent early-type galaxies, but our current census of them does not form a complete picture. Recent studies of nearby case studies seem to have identified a population of galaxies that quench "quietly." Traditional poststarburst searches seem to catch galaxies only after they have quenched and transformed, and thus miss any objects with additional ionization mechanisms exciting the remaining gas. The Shocked POststarburst Galaxy Survey (SPOGS) aims to identify galaxies in an earlier phase of transformation, in which the nebular lines are excited via shocks instead of through star formation processes. Utilizing the OSSY measurements on the Sloan Digital Sky Survey Data Release 7 catalog, we applied Balmer absorption and shock boundary criteria to identify 1,067 SPOG candidates (SPOGs*) within z = 0.2. SPOGs* represent 0.7% of emission line galaxies (and 0.2% of OSSY). SPOGs* colors suggest that they ...

  13. Air-fuel ratio and speed control for low emission vehicles based on sliding mode techniques

    Energy Technology Data Exchange (ETDEWEB)

    Puleston, P.F. [UNLP, La Plata (Argentina). Departamento de Electrotecnia, CONICET and LEICI; Monsees, G. [Delft University of Technology (Netherlands). Faculty of Information, Technology and Systems, Control Laboratory; Spurgeon, S.K. [University of Leicester (United Kingdom). Department of Engineering, Control and Instrumentation Group

    2002-05-01

    This paper deals with the combined air-fuel ratio (AFR) and speed control of automotive engines. The robust controller is developed using dynamic sliding mode (SM) control design methods. The proposed controller set-up is tested under realistic operating conditions by means of computer simulation using a comprehensive non-linear model of a four-stroke engine, specifically provided by the automotive industry for these purposes. This accurate industrial model comprises extensive dynamics description and numerous look-up tables representing parameter characteristics obtained from experimental data. The SM controller set-up proves to be robust to model uncertainties and unknown disturbances, regulating effectively the engine speed for a wide range of set-points while maintaining the AFR at the stoichiometric value. (author)

  14. Volatile Organic Compound (VOC) Testing at Building 348, Kelly AFB, Texas.

    Science.gov (United States)

    1987-11-01

    At the request of HQ AFLC/ SGB , the USAFOEHL conducted a stack sampling survey to determine total volatile organic compounds (VOC) being emitted from...Occupational and Environmental Health Laboratory (USAFOEHL/ECQ). The survey was requested by HQ AFLC/ SGB .to estimate VOC emissions through each of...stardards. 2. Range and Sensitivity 2.1 This method was validated over the range of 1417-5940 mg/M at an atmospheric temperature and pressure of 24 0C

  15. VOLATILE ORGANIC COMPOUND EMISSION RATES FROM MIXED DECIDUOUS AND CONIFEROUS FORESTS IN NORTHERN WISCONSIN, USA

    Science.gov (United States)

    Biogenic emissions of volatile organic compounds (VOC) from forests play an important role in regulating the atmospheric trace gas composition including global tropospheric ozone concentrations. However, more information is needed on VOC emission rates from different forest regio...

  16. Primary emissions and secondary formation of volatile organic compounds from natural gas production in five major U.S. shale plays

    Science.gov (United States)

    Gilman, J.; Lerner, B. M.; Warneke, C.; Graus, M.; Lui, R.; Koss, A.; Yuan, B.; Murphy, S. M.; Alvarez, S. L.; Lefer, B. L.; Min, K. E.; Brown, S. S.; Roberts, J. M.; Osthoff, H. D.; Hatch, C. D.; Peischl, J.; Ryerson, T. B.; De Gouw, J. A.

    2014-12-01

    According to the U.S. Energy and Information Administration (EIA), domestic production of natural gas from shale formations is currently at the highest levels in U.S. history. Shale gas production may also result in the production of natural gas plant liquids (NGPLs) such as ethane and propane as well as natural gas condensate composed of a complex mixture of non-methane hydrocarbons containing more than ~5 carbon atoms (e.g., hexane, cyclohexane, and benzene). The amounts of natural gas liquids and condensate produced depends on the particular reservoir. The source signature of primary emissions of hydrocarbons to the atmosphere within each shale play will therefore depend on the composition of the raw natural gas as well as the industrial processes and equipment used to extract, separate, store, and transport the raw materials. Characterizing the primary emissions of VOCs from natural gas production is critical to assessing the local and regional atmospheric impacts such as the photochemical formation of ozone and secondary formation of organic aerosol. This study utilizes ground-based measurements of a full suite of volatile organic compounds (VOCs) in two western U.S. basins, the Uintah (2012-2014 winter measurements only) and Denver-Julesburg (winter 2011 and summer 2012), and airborne measurements over the Haynesville, Fayetteville, and Marcellus shale basins (summer 2013). By comparing the observed VOC to propane enhancement ratios, we show that each basin has a unique VOC source signature associated with oil and natural gas operations. Of the shale basins studied, the Uintah basin had the largest overall VOC to propane enhancement ratios while the Marcellus had the lowest. For the western basins, we will compare the composition of oxygenated VOCs produced from photochemical oxidation of VOC precursors and contrast the oxygenated VOC mixture to a "typical" summertime urban VOC mixture. The relative roles of alkanes, alkenes, aromatics, and cycloalkanes as

  17. Effect of Air Staging Ratios on the Burning Rate and Emissions in an Underfeed Fixed-Bed Biomass Combustor

    Directory of Open Access Journals (Sweden)

    Araceli Regueiro

    2016-11-01

    Full Text Available This experimental work studies a small-scale biomass combustor (5–12 kW with an underfed fixed bed using low air staging ratios (15%–30%. This document focuses on the influence of the operative parameters on the combustion process, so gaseous emissions and the distribution and concentration of particulate matter have also been recorded. The facility shows good stability and test repeatability. For the studied airflow ranges, the results show that increasing the total airflow rate does not increase the overall air excess ratio because the burning rate is proportionally enhanced (with some slight differences that depend on the air staging ratio. Consequently, the heterogeneous reactions at the bed remain in the so-called oxygen-limited region, and thus the entire bed operates under sub-stoichiometric conditions with regards of the char content of the biomass. In addition, tests using only primary air (no staging may increase the fuel consumption, but in a highly incomplete way, approaching a gasification regime. Some measured burning rates are almost 40% higher than previous results obtained in batch combustors due to the fixed position of the ignition front. The recorded concentration of particulate matter varies between 15 and 75 mg/Nm3, with a main characteristic diameter between 50 and 100 nm.

  18. Review on Volatile Organic Compounds Emission from Wood Composites

    Institute of Scientific and Technical Information of China (English)

    LIU Yu; YU Yaoming; SHEN Jun; LIU Ming

    2006-01-01

    The problem of indoor air quality (IAQ) is mainly caused by the volatile organic compounds (VOC) emission from the wood-based composites. As a material for decoration, furniture manufacturing or building, wood-based composite is one of the sources of VOC emissions. Most of them are formaldehyde, terpene, ketone and benzene. The paper reviews on VOC emission of wood-based composites at home and abroad, including the source of the VOC, its impacts on IAQ, its emission during processing and using, the usual sampling and analyse methods of VOC in different conditions. Meanwhile, main problems existed in the past researches are summarized and some suggestions are put forward.

  19. Prospects for measuring the fuel ion ratio in burning ITER plasmas using a DT neutron emission spectrometer

    Science.gov (United States)

    Hellesen, C.; Skiba, M.; Dzysiuk, N.; Weiszflog, M.; Hjalmarsson, A.; Ericsson, G.; Conroy, S.; Andersson-Sundén, E.; Eriksson, J.; Binda, F.

    2014-11-01

    The fuel ion ratio nt/nd is an essential parameter for plasma control in fusion reactor relevant applications, since maximum fusion power is attained when equal amounts of tritium (T) and deuterium (D) are present in the plasma, i.e., nt/nd = 1.0. For neutral beam heated plasmas, this parameter can be measured using a single neutron spectrometer, as has been shown for tritium concentrations up to 90%, using data obtained with the MPR (Magnetic Proton Recoil) spectrometer during a DT experimental campaign at the Joint European Torus in 1997. In this paper, we evaluate the demands that a DT spectrometer has to fulfill to be able to determine nt/nd with a relative error below 20%, as is required for such measurements at ITER. The assessment shows that a back-scattering time-of-flight design is a promising concept for spectroscopy of 14 MeV DT emission neutrons.

  20. Characterization of volatile organic compounds (VOCs in Asian and North American pollution plumes during INTEX-B: identification of specific Chinese air mass tracers

    Directory of Open Access Journals (Sweden)

    B. Barletta

    2009-03-01

    Full Text Available We present results from the Intercontinental Chemical Transport Experiment – Phase B (INTEX-B aircraft mission conducted in spring 2006. By analyzing the mixing ratios of volatile organic compounds (VOCs measured during the second part of the field campaign, together with kinematic back trajectories, we were able to identify five plumes originating from China, four plumes from other Asian regions, and three plumes from the United States. To identify specific tracers for the different air masses, we focused on characterizing the VOC composition of these different pollution plumes. The Chinese and other Asian air masses were significantly enhanced in carbonyl sulfide (OCS and methyl chloride (CH3Cl, while all CFC replacement compounds were elevated in US plumes, particularly HCFC-134a.

    Although elevated mixing ratios of Halon-1211 were measured in some of the Chinese plumes, several measurements at background levels were also observed. After analyzing the VOC distribution in the Chinese pollution plumes and the correlations among selected compounds, we suggest the use of a suite of species, rather than the use of a single gas, to be used as specific tracers of Chinese air masses (namely OCS, CH3Cl, 1,2-dichloroethane, and Halon-1211. In an era of constantly changing halocarbon usage patterns, this suite of gases best reflects new emission characteristics from China.

  1. Characterization of volatile organic compounds (VOCs in Asian and north American pollution plumes during INTEX-B: identification of specific Chinese air mass tracers

    Directory of Open Access Journals (Sweden)

    A. J. Weinheimer

    2009-07-01

    Full Text Available We present results from the Intercontinental Chemical Transport Experiment – Phase B (INTEX-B aircraft mission conducted in spring 2006. By analyzing the mixing ratios of volatile organic compounds (VOCs measured during the second part of the field campaign, together with kinematic back trajectories, we were able to identify five plumes originating from China, four plumes from other Asian regions, and three plumes from the United States. To identify specific tracers for the different air masses we characterized their VOC composition and we compared their background levels with those obtained during the 2004 INTEX-A mission. The Chinese and other Asian air masses were significantly enhanced in carbonyl sulfide (OCS and methyl chloride (CH3Cl, while all CFC replacement compounds were elevated in US plumes, particularly HFC-134a.

    Although elevated mixing ratios of Halon-1211 were measured in some Chinese plume samples, several measurements at background levels were also observed. After analyzing the VOC distribution and correlations within the Chinese pollution plumes and applying principal component analysis (PCA, we suggest the use of a suite of species, rather than a single gas, as specific tracers of Chinese air masses (namely OCS, CH3Cl, 1,2-dichloroethane, ethyl chloride, and Halon-1211. In an era of constantly changing halocarbon usage patterns, this suite of gases best reflects new emission characteristics from China.

  2. Influence of the Gas Mixture Ratio on the Correlations Between the Excimer XeCl* Emission and the Sealed Gas Temperature in Dielectric Barrier Discharge Lamps

    Institute of Scientific and Technical Information of China (English)

    徐金洲; 梁荣庆; 任兆杏

    2002-01-01

    For dielectric barrier discharge lamps filled with various gas mixture ratios, the correlations between the excimer XeCl* emission and the sealed gas temperature have been founded, and a qualitative explication is presented. For gas mixture with chlorine larger than 3%, the emission intensity increases with the sealed gas temperature, while with chlorine about 2%, the emission intensity decreases with the increase in the gas temperature, and could be improved by cooling water. However, if chlorine is less than 1.5%, the discharge appears to be a mixture mode with filaments distributed in a diffused glow-like discharge, and the UV emission is independent on the gas temperature.

  3. Modeling signal-to-noise ratio of otoacoustic emissions in workers exposed to different industrial noise levels

    Directory of Open Access Journals (Sweden)

    Parvin Nassiri

    2016-01-01

    Full Text Available Introduction: Noise is considered as the most common cause of harmful physical effects in the workplace. A sound that is generated from within the inner ear is known as an otoacoustic emission (OAE. Distortion-product otoacoustic emissions (DPOAEs assess evoked emission and hearing capacity. The aim of this study was to assess the signal-to-noise ratio in different frequencies and at different times of the shift work in workers exposed to various levels of noise. It was also aimed to provide a statistical model for signal-to-noise ratio (SNR of OAEs in different frequencies based on the two variables of sound pressure level (SPL and exposure time. Materials and Methods: This case–control study was conducted on 45 workers during autumn 2014. The workers were divided into three groups based on the level of noise exposure. The SNR was measured in frequencies of 1000, 2000, 3000, 4000, and 6000 Hz in both ears, and in three different time intervals during the shift work. According to the inclusion criterion, SNR of 6 dB or greater was included in the study. The analysis was performed using repeated measurements of analysis of variance, spearman correlation coefficient, and paired samples t-test. Results: The results showed that there was no statistically significant difference between the three exposed groups in terms of the mean values of SNR (P > 0.05. Only in signal pressure levels of 88 dBA with an interval time of 10:30–11:00 AM, there was a statistically significant difference between the right and left ears with the mean SNR values of 3000 frequency (P = 0.038. The SPL had a significant effect on the SNR in both the right and left ears (P = 0.023, P = 0.041. The effect of the duration of measurement on the SNR was statistically significant in both the right and left ears (P = 0.027, P < 0.001. Conclusion: The findings of this study demonstrated that after noise exposure during the shift, SNR of OAEs reduced from the

  4. Rapid leaf development drives the seasonal pattern of volatile organic compound (VOC) fluxes in a 'coppiced' bioenergy poplar plantation.

    Science.gov (United States)

    Brilli, Federico; Gioli, Beniamino; Fares, Silvano; Terenzio, Zenone; Zona, Donatella; Gielen, Bert; Loreto, Francesco; Janssens, Ivan A; Ceulemans, Reinhart

    2016-03-01

    Leaves of fast-growing, woody bioenergy crops often emit volatile organic compounds (VOC). Some reactive VOC (especially isoprene) play a key role in climate forcing and may negatively affect local air quality. We monitored the seasonal exchange of VOC using the eddy covariance technique in a 'coppiced' poplar plantation. The complex interactions of VOC fluxes with climatic and physiological variables were also explored by using an artificial neural network (Self Organizing Map). Isoprene and methanol were the most abundant VOC emitted by the plantation. Rapid development of the canopy (and thus of the leaf area index, LAI) was associated with high methanol emissions and high rates of gross primary production (GPP) since the beginning of the growing season, while the onset of isoprene emission was delayed. The highest emissions of isoprene, and of isoprene photo-oxidation products (Methyl Vinyl Ketone and Methacrolein, iox ), occurred on the hottest and sunniest days, when GPP and evapotranspiration were highest, and formaldehyde was significantly deposited. Canopy senescence enhanced the exchange of oxygenated VOC. The accuracy of methanol and isoprene emission simulations with the Model of Emissions of Gases and Aerosols from Nature increased by applying a function to modify their basal emission factors, accounting for seasonality of GPP or LAI. © 2015 John Wiley & Sons Ltd.

  5. Plant volatile organic compounds (VOCs) in ozone (O3) polluted atmospheres: the ecological effects.

    Science.gov (United States)

    Pinto, Delia M; Blande, James D; Souza, Silvia R; Nerg, Anne-Marja; Holopainen, Jarmo K

    2010-01-01

    Tropospheric ozone (O3) is an important secondary air pollutant formed as a result of photochemical reactions between primary pollutants, such as nitrogen oxides (NOx), and volatile organic compounds (VOCs). O3 concentrations in the lower atmosphere (troposphere) are predicted to continue increasing as a result of anthropogenic activity, which will impact strongly on wild and cultivated plants. O3 affects photosynthesis and induces the development of visible foliar injuries, which are the result of genetically controlled programmed cell death. It also activates many plant defense responses, including the emission of phytogenic VOCs. Plant emitted VOCs play a role in many eco-physiological functions. Besides protecting the plant from abiotic stresses (high temperatures and oxidative stress) and biotic stressors (competing plants, micro- and macroorganisms), they drive multitrophic interactions between plants, herbivores and their natural enemies e.g., predators and parasitoids as well as interactions between plants (plant-to-plant communication). In addition, VOCs have an important role in atmospheric chemistry. They are O3 precursors, but at the same time are readily oxidized by O3, thus resulting in a series of new compounds that include secondary organic aerosols (SOAs). Here, we review the effects of O3 on plants and their VOC emissions. We also review the state of current knowledge on the effects of ozone on ecological interactions based on VOC signaling, and propose further research directions.

  6. Impact of air pressure on volatile organic compound emissions from a carpet

    Institute of Scientific and Technical Information of China (English)

    高鹏; 邓琴琴; LIN; Chao-hsin; 杨旭东

    2009-01-01

    The measurement of volatile organic compound (VOC) emissions from materials is normally conducted under standard environmental conditions, i.e., (23±1) ℃ temperature, (50±5)% relative humidity, and 0.1 MPa pressure. In order to define VOC emissions in non-standard environmental conditions, it is necessary to study the impact of key environmental parameters on emissions. This paper evaluates the impact of air pressure on VOC emissions from an aircraft carpet. The correlation between air pressure and VOC diffusion coefficient is derived, and the emission model is applied to studying the VOC emissions under pressure conditions of less than 0.1 MPa.

  7. Reactivity of ambient volatile organic compounds (VOCs) in summer of 2004 in Beijing

    Institute of Scientific and Technical Information of China (English)

    Shan Huang; Min Shao; Sihua Lu; Ying Liu

    2008-01-01

    Ambient volatile organic compounds (VOCs) were sampled at six sites in Beijing in the summer of 2004 and analyzed byGCMS. The chemical reactivities of 73 quantified VOCs species were evaluated by OH loss rates (L<,OH) and ozone formationpotentials (OFPs). Top 15 reactive species, mainly alkenes and aromatics, were identified by these two methods, and accounted formore than 70% of total reactivity of VOCs. In urban areas, isoprene was the most reactive species in term of OH loss rate,contributing 11.4% to the Loft of VOCs. While toluene, accounting for 9.4% of OFPs, appeared to have a long-time role in thephotochemical processes. Tongzhou site is obviously influenced by local chemical industry, but the other five sites showed typicalurban features influenced mainly by vehicular emissions.2008 Min Shao. Published by Elsevier B.V. on behalf of Chinese Chemical Society. All rights reserved.

  8. Qualitative tissue differentiation by analysing the intensity ratios of atomic emission lines using laser induced breakdown spectroscopy (LIBS): prospects for a feedback mechanism for surgical laser systems.

    Science.gov (United States)

    Kanawade, Rajesh; Mahari, Fanuel; Klämpfl, Florian; Rohde, Maximilian; Knipfer, Christian; Tangermann-Gerk, Katja; Adler, Werner; Schmidt, Michael; Stelzle, Florian

    2015-01-01

    The research work presented in this paper focuses on qualitative tissue differentiation by monitoring the intensity ratios of atomic emissions using 'Laser Induced Breakdown Spectroscopy' (LIBS) on the plasma plume created during laser tissue ablation. The background of this study is to establish a real time feedback control mechanism for clinical laser surgery systems during the laser ablation process. Ex-vivo domestic pig tissue samples (muscle, fat, nerve and skin) were used in this experiment. Atomic emission intensity ratios were analyzed to find a characteristic spectral line for each tissue. The results showed characteristic elemental emission intensity ratios for the respective tissues. The spectral lines and intensity ratios of these specific elements varied among the different tissue types. The main goal of this study is to qualitatively and precisely identify different tissue types for tissue specific laser surgery. © 2015 The Authors. Journal of Biophotonics published by WILEY-VCH Verlag.

  9. Enhancement of red to orange emission ratio of YPO4:Eu3+,Ce3+ and its dependence on Ce3+ concentration

    Institute of Scientific and Technical Information of China (English)

    ZHAN Shiping; GAO Yongyi; LIU Yunxin; ZHONG Hui

    2012-01-01

    Eu3+ and Ce3+ co-doped YPO4 microspheres were synthesized by hydrothermal method without template.The emission spectra showed that the red emission centered at 618 nm could be readily increased relatively to the orange emission centered at 590 nm by controlling the doping concentration of Ce3+ ion.The investigation based on excitation spectra and decay curves demonstrated that the doped Ce3+ ions took two efficient energy transfers to Eu3+ ions and affected the lifetime of the emission states ofEu3+ ions so that the emission spectra of Eu3+ ion were accordingly tuned with the Ce3+ content increasing.This controllable red (5D0→7F2) to orange (5D0→7F1) emission ratio of YPO4:Eu3+,Ce3+ made it very promising for encoded anti-fake labels and bio-labels.

  10. Indoor contaminants from Hardcopy Devices: Characteristics of VOCs in photocopy centers

    Science.gov (United States)

    Sarkhosh, Maryam; Mahvi, Amir Hossein; Zare, Mohammad Reza; Fakhri, Yadolah; Shamsolahi, Hamid Reza

    2012-12-01

    Indoor air pollution in working places is widely recognized as one of the most serious potential environment risks to human health. Mean volatile organic compound (VOC) concentrations of 144 samples from four copy centers in Tehran, Iran in two seasons were monitored for the purpose of quantifying the various VOCs in these areas. Area samples were collected in thermal desorption tubes and were analyzed using gas chromatography/mass selective detector. Real-time personal total volatile organic compounds were measured using a data-logging photo-ionization detector. Simultaneously, BTEX (benzene, toluene, ethylbenzene, xylenes) outdoor measurements were performed in the same manner as were the indoor measurements. Nineteen different VOCs were detected in the area samples. The results show that in all photocopy centers, the indoor levels of toluene were much higher than the outdoor levels. During business hours, the VOC levels increased, especially toluene indoor concentration. The ventilation decreased the indoor VOC concentrations. The background and indoor VOC concentrations were higher in winter than in spring. The minimum ratio of the indoor to outdoor concentration of BTEX was estimated to be more than 42. This value proved that buildings with photocopiers can be a site of VOC accumulation.

  11. VOC reactivity and its effect on ozone production during the HaChi summer campaign

    Directory of Open Access Journals (Sweden)

    L. Ran

    2011-05-01

    Full Text Available Measurements of ozone and its precursors conducted within the HaChi (Haze in China project in summer 2009 were analyzed to characterize volatile organic compounds (VOCs and their effects on ozone photochemical production at a suburban site in the North China Plain (NCP. Ozone episodes, during which running 8-h average ozone concentrations exceeding 80 ppbv lasted for more than 4 h, occurred on about two thirds of the observational days during the 5-week field campaign. This suggests continuous ozone exposure risks in this region in the summer. Average concentrations of nitrogen oxides (NOx and VOCs are about 20 ppbv and 650 ppbC, respectively. On average, total VOC reactivity is dominated by anthropogenic VOCs. The contribution of biogenic VOCs to total ozone-forming potential, however, is also considerable in the daytime. Key species associated with ozone photochemical production are 2-butenes (18 %, isoprene (15 %, trimethylbenzenes (11 %, xylenes (8.5 %, 3-methylhexane (6 %, n-hexane (5 % and toluene (4.5 %. Formation of ozone is found to be NOx-limited as indicated by measured VOCs/NOx ratios and further confirmed by a sensitivity study using a photochemical box model NCAR_MM. The Model simulation suggests that ozone production is also sensitive to changes in VOC reactivity under the NOx-limited regime, although this sensitivity depends strongly on how much NOx is present.

  12. Influence of fuel type, dilution and equivalence ratio on the emission reduction from the auto-ignition in an Homogeneous Charge Compression Ignition engine

    Energy Technology Data Exchange (ETDEWEB)

    Machrafi, Hatim [UPMC Universite Paris 06, ENSCP, 11 rue de Pierre et Marie Curie, 75005 Paris (France); UPMC Universite Paris 06, Institut Jean Le Rond D' Alembert, 4 place Jussieu, 75252 Paris cedex 05 (France); Universite Libre de Bruxelles, TIPs - Fluid Physics, CP165/67, 50 Avenue F.D. Roosevelt, 1050 Brussels (Belgium); Cavadias, Simeon [UPMC Universite Paris 06, ENSCP, 11 rue de Pierre et Marie Curie, 75005 Paris (France); UPMC Universite Paris 06, Institut Jean Le Rond D' Alembert, 4 place Jussieu, 75252 Paris cedex 05 (France); Amouroux, Jacques [UPMC Universite Paris 06, ENSCP, 11 rue de Pierre et Marie Curie, 75005 Paris (France)

    2010-04-15

    One technology that seems to be promising for automobile pollution reduction is the Homogeneous Charge Compression Ignition (HCCI). This technology still faces auto-ignition and emission-control problems. This paper focuses on the emission problem, since it is incumbent to realize engines that pollute less. For this purpose, this paper presents results concerning the measurement of the emissions of CO, NO{sub x}, CO{sub 2}, O{sub 2} and hydrocarbons. HCCI conditions are used, with equivalence ratios between 0.26 and 0.54, inlet temperatures of 70 C and 120 C and compression ratios of 10.2 and 13.5, with different fuel types: gasoline, gasoline surrogate, diesel, diesel surrogate and mixtures of n-heptane/toluene. The effect of dilution is considered for gasoline, while the effect of the equivalence ratio is considered for all the fuels. No significant amount of NO{sub x} has been measured. It appeared that the CO, O{sub 2} and hydrocarbon emissions were reduced by decreasing the toluene content of the fuel and by decreasing the dilution. The opposite holds for CO{sub 2}. The reduction of the hydrocarbon emission appears to compete with the reduction of the CO{sub 2} emission. Diesel seemed to produce less CO and hydrocarbons than gasoline when auto-ignited. An example of emission reduction control is presented in this paper. (author)

  13. T2VOC user`s guide

    Energy Technology Data Exchange (ETDEWEB)

    Falta, R.W. [Clemson Univ., Clemson, SC (United States). Dept. of Earth Sciences; Pruess, K.; Finsterle, S. [Lawrence Berkeley Lab., CA (United States); Battistelli, A. [AQUATER S.p.A., San Lorenzo in Campo, (Italy)

    1995-03-01

    T2VOC is a numerical simulator for three-phase, three-component, non-isothermal flow of water, air, and a volatile organic compound (VOC) in multidimensional heterogeneous porous media. Developed at the Lawrence Berkeley Laboratory, T2VOC is an extension of the TOUGH2 general-purpose simulation program. This report is a self-contained guide to application of T2VOC to subsurface contamination problems involving nonaqueous phase liquids (NAPLs). It gives a technical description of the T2VOC code, including a discussion of the physical processes modeled, and the mathematical and numerical methods used. Detailed instructions for preparing input data are presented along with several illustrative sample problems.

  14. Measurements of VOC fluxes by Eddy-covariance with a PTR-Qi-TOF-MS over a mature wheat crop near Paris: Evaluation of data quality and uncertainties.

    Science.gov (United States)

    Buysse, Pauline; Loubet, Benjamin; Ciuraru, Raluca; Lafouge, Florence; Zurfluh, Olivier; Gonzaga-Gomez, Lais; Fanucci, Olivier; Gueudet, Jean-Christophe; Decuq, Céline; Gros, Valérie; Sarda, Roland; Zannoni, Nora

    2017-04-01

    The quantification of volatile organic compounds (VOC) fluxes exchanged by terrestrial ecosystems is of large interest because of their influence on the chemistry and composition of the atmosphere including aerosols and oxidants. Latest developments in the techniques for detecting, identifying and measuring VOC fluxes have considerably improved the abilities to get reliable estimates. Among these, the eddy-covariance (EC) methodology constitutes the most direct approach, and relies on both well-established principles (Aubinet et al. 2000) and a sound continuously worldwide improving experience. The combination of the EC methodology with the latest proton-transfer-reaction mass spectrometer (PTR-MS) device, the PTR-Qi-TOF-MS, which allows the identification and quantification of more than 500 VOC at high frequency, now provides a very powerful and precise tool for an accurate quantification of VOC fluxes on various types of terrestrial ecosystems. The complexity of the whole methodology however demands that several data quality requirements are fulfilled. VOC fluxes were measured by EC with a PTR-Qi-TOF-MS (national instrument within the ANAEE-France framework) for one month and a half over a mature wheat crop near Paris (FR-GRI ICOS site). Most important emissions (by descending order) were observed from detected compounds with mass-over-charge (m/z) ratios of 33.033 (methanol), 45.033 (acetaldehyde), 93.033 (not identified yet), 59.049 (acetone), and 63.026 (dimethyl sulfide or DMS). Emissions from higher-mass compounds, which might be due to pesticide applications at the beginning of our observation period, were also detected. Some compounds were also seen to deposit (e.g. m/z 47.013, 71.085, 75.044, 83.05) while others exhibited bidirectional fluxes (e.g. m/z 57.07, 69.07). Before analyzing VOC flux responses to meteorological and crop development drivers, a data quality check was performed which included (i) uncertainty analysis of mass and concentration

  15. Characterization of on-road vehicle emissions in the Mexico City Metropolitan Area using a mobile laboratory in chase and fleet average measurement modes during the MCMA-2003 field campaign

    Science.gov (United States)

    Zavala, M.; Herndon, S. C.; Slott, R. S.; Dunlea, E. J.; Marr, L. C.; Shorter, J. H.; Zahniser, M.; Knighton, W. B.; Rogers, T. M.; Kolb, C. E.; Molina, L. T.; Molina, M. J.

    2006-11-01

    A mobile laboratory was used to measure on-road vehicle emission ratios during the MCMA-2003 field campaign held during the spring of 2003 in the Mexico City Metropolitan Area (MCMA). The measured emission ratios represent a sample of emissions of in-use vehicles under real world driving conditions for the MCMA. From the relative amounts of NOx and selected VOC's sampled, the results indicate that the technique is capable of differentiating among vehicle categories and fuel type in real world driving conditions. Emission ratios for NOx, NOy, NH3, H2CO, CH3CHO, and other selected volatile organic compounds (VOCs) are presented for chase sampled vehicles in the form of frequency distributions as well as estimates for the fleet averaged emissions. Our measurements of emission ratios for both CNG and gasoline powered "colectivos" (public transportation buses that are intensively used in the MCMA) indicate that - in a mole per mole basis - have significantly larger NOx and aldehydes emissions ratios as compared to other sampled vehicles in the MCMA. Similarly, ratios of selected VOCs and NOy showed a strong dependence on traffic mode. These results are compared with the vehicle emissions inventory for the MCMA, other vehicle emissions measurements in the MCMA, and measurements of on-road emissions in U.S. cities. We estimate NOx emissions as 100 600±29 200 metric tons per year for light duty gasoline vehicles in the MCMA for 2003. According to these results, annual NOx emissions estimated in the emissions inventory for this category are within the range of our estimated NOx annual emissions. Our estimates for motor vehicle emissions of benzene, toluene, formaldehyde, and acetaldehyde in the MCMA indicate these species are present in concentrations higher than previously reported. The high motor vehicle aldehyde emissions may have an impact on the photochemistry of urban areas.

  16. Characterization of on-road vehicle emissions in the Mexico City Metropolitan Area using a mobile laboratory in chase and fleet average measurement modes during the MCMA-2003 field campaign

    Directory of Open Access Journals (Sweden)

    M. Zavala

    2006-01-01

    Full Text Available A mobile laboratory was used to measure on-road vehicle emission ratios during the MCMA-2003 field campaign held during the spring of 2003 in the Mexico City Metropolitan Area (MCMA. The measured emission ratios represent a sample of emissions of in-use vehicles under real world driving conditions for the MCMA. From the relative amounts of NOx and selected VOC's sampled, the results indicate that the technique is capable of differentiating among vehicle categories and fuel type in real world driving conditions. Emission ratios for NOx, NOy, NH3, H2CO, CH3CHO, and other selected volatile organic compounds (VOCs are presented for chase sampled vehicles in the form of frequency distributions as well as estimates for the fleet averaged emissions. Our measurements of emission ratios for both CNG and gasoline powered "colectivos" (public transportation buses that are intensively used in the MCMA indicate that – in a mole per mole basis – have significantly larger NOx and aldehydes emissions ratios as compared to other sampled vehicles in the MCMA. Similarly, ratios of selected VOCs and NOy showed a strong dependence on traffic mode. These results are compared with the vehicle emissions inventory for the MCMA, other vehicle emissions measurements in the MCMA, and measurements of on-road emissions in U.S. cities. We estimate NOx emissions as 100 600±29 200 metric tons per year for light duty gasoline vehicles in the MCMA for 2003. According to these results, annual NOx emissions estimated in the emissions inventory for this category are within the range of our estimated NOx annual emissions. Our estimates for motor vehicle emissions of benzene, toluene, formaldehyde, and acetaldehyde in the MCMA indicate these species are present in concentrations higher than previously reported. The high motor vehicle aldehyde emissions may have an impact on the photochemistry of urban areas.

  17. Use of Combined Observational- and Model-Derived Photochemical Indicators to Assess the O3-NOx-VOC System Sensitivity in Urban Areas

    Directory of Open Access Journals (Sweden)

    Edson R. Carrillo-Torres

    2017-01-01

    Full Text Available Tropospheric levels of O3 have historically exceeded the official annual Mexican standards within the Monterrey Metropolitan Area (MMA in NE Mexico. High-frequency and high-precision measurements of tropospheric O3, NOy, NO2, NO, CO, SO2, PM10 and PM2.5 were made at the Obispado monitoring site near the downtown MMA from September 2012 to August 2013. The seasonal cycles of O3 and NOy are driven by changes in meteorology and to a lesser extent by variations in primary emissions. The NOy levels were positively correlated with O3 precursors and inversely correlated with O3 and wind speed. Recorded data were used to assess the O3-Volatile Organic Compounds (VOC-NOx system’s sensitivity through an observational-based approach. The photochemical indicator O3/NOy was derived from measured data during the enhanced O3 production period (12:00–18:00 Central Daylight Time (CDT, GMT-0500. The O3/NOy ratios calculated for this time period showed that the O3 production within the MMA is VOC sensitive. A box model simulation of production rates of HNO3 (PHNO3 and total peroxides (Pperox carried out for O3 episodes in fall and spring confirmed the VOC sensitivity within the MMA environment. No significant differences were observed in O3/NOy from weekdays to weekends or for PHNO3/Pperox ratios, confirming the limiting role of VOCs in O3 production within the MMA. The ratified photochemical regime observed may allow the environmental authorities to revise and verify the current policies for air quality control within the MMA.

  18. Biofiltration for control of volatile organic compounds (VOCS)

    Energy Technology Data Exchange (ETDEWEB)

    Bishop, D.F. [Environmental Protection Agency, Cincinnati, OH (United States); Govind, R. [Univ. of Cincinnati, OH (United States)

    1995-10-01

    Air biofiltration is a promising technology for control of air emissions of biodegradable volatile organic compounds (VOCs). In conjunction with vacuum extraction of soils or air stripping of ground water, it can be used to mineralize VOCs removed from contaminated soil or groundwater. The literature describes three major biological systems for treating contaminated air bioscrubbers, biotrickling filters and biofilters. Filter media can be classified as: bioactive fine or irregular particulates, such as soil, peat, compost or mixtures of these materials; pelletized, which are randomly packed in a bed; and structured, such as monoliths with defined or variable passage size and geometry. The media can be made of sorbing and non-absorbing materials. Non-bioactive pelletized and structured media require recycled solutions of nutrients and buffer for efficient microbial activity and are thus called biotrickling filters. Extensive work has been conducted to improve biofiltration by EPA`s Risk Reduction Engineering Laboratory and the University of Cincinnati in biofilters using pelletized and structured media and improved operational approaches. Representative VOCs in these studies included compounds with a range of aqueous solubilities and octanol-water partition coefficients. The compounds include iso-pentane, toluene, methylene chloride, trichloroethylene (TCE), ethyl benzene, chlorobenzene and perchloroethylene (PCE) and alpha ({alpha}-) pinene. Comparative studies were conducted with peat/compost biofilters using isopentane and {alpha}-pinene. Control studies were also conducted to investigate adsorption/desorption of contaminants on various media using mercuric chloride solution to insure the absence of bioactivity.

  19. Low HAP/VOC Compliant Resins for Military Applications

    Science.gov (United States)

    2011-09-01

    on lauric acid FAVE-O fatty acid vinyl ester resin system based on octanoic acid FTIR Fourier transform infrared GIC Mode 1 fracture energy...temperature and could potentially produce smog-promoting ozone as well as long-term and acute health effects. VOC/HAPs are emitted during all phases of...Viscosity ា cP at 25 °C (MOct) Unreacted epoxy FTIR *, NMR* No epoxy present None detected Correct reactant ratios NMR Methacrylate to FA ratio of 1:1

  20. 利用SOF-FTIR监测重庆晏家工业区挥发性有机物排放%Monitoring of VOCs Emissions of Yanjia Industrial Park in Chongqing Based on SOF-FTIR Technology

    Institute of Scientific and Technical Information of China (English)

    翟崇治; 刘芮伶; 许丽萍; 金岭; 余家燕; 李礼; 刘敏

    2015-01-01

    挥发性有机物(VOCs)是光化学污染物的主要前体物,是影响城市和区域大气质量的重要污染物.工业生产过程中排放的VOCs种类、来源和污染特征复杂,测量中存在许多未知因素,且一直缺乏便捷和快速的监测手段.利用基于太阳直射光的车载太阳掩星傅里叶红外光谱技术(Solar Occultation Flux-FTIR,SOF-FTIR)快速扫描长寿晏家工业区并进行实时VOCs监测,获得其垂直柱浓度,大多浓度最大值位于10~60 ppm·m区间,且该工业区易形成局地污染汇聚.

  1. Constraining the dynamical importance of hot gas and radiation pressure in quasar outflows using emission line ratios

    CERN Document Server

    Stern, Jonathan; Zakamska, Nadia L; Hennawi, Joseph F

    2015-01-01

    Quasar feedback models often predict an expanding hot gas bubble which drives a galaxy-scale outflow. In many circumstances the hot gas is predicted to radiate inefficiently, making the hot bubble hard to observe directly. We present an indirect method to detect the presence of a hot bubble using hydrostatic photoionization models of the cold (10^4 K) line-emitting gas. These models assume that the cold gas is in pressure equilibrium with either the hot gas pressure or with the radiation pressure, whichever is larger. We compare our models with observations of the broad line region (BLR), the inner face of the dusty torus, the narrow line region (NLR), and the extended NLR, and thus constrain the hot gas pressure over a dynamical range of 10^5 in radius, from 0.1 pc to 10 kpc. We find that the emission line ratios observed in the average quasar spectrum are consistent with radiation-pressure-dominated models on all scales. On scales > L_AGN/c inferred for galaxy-scale outflows in luminous quasars. This appare...

  2. A High Fraction of Ly-alpha-Emitters Among Galaxies with Extreme Emission Line Ratios at z ~ 2

    CERN Document Server

    Erb, Dawn K; Steidel, Charles C; Strom, Allison L; Rudie, Gwen C; Trainor, Ryan F; Shapley, Alice E; Reddy, Naveen A

    2016-01-01

    Star-forming galaxies form a sequence in the [OIII]/H-beta vs. [NII]/H-alpha diagnostic diagram, with low metallicity, highly ionized galaxies falling in the upper left corner. Drawing from a large sample of UV-selected star-forming galaxies at z~2 with rest-frame optical nebular emission line measurements from Keck-MOSFIRE, we select the extreme ~5% of the galaxies lying in this upper left corner, requiring log([NII]/H-alpha) = 0.75. These cuts identify galaxies with 12 + log(O/H) 20 A. We compare the equivalent width distribution of a sample of 522 UV-selected galaxies at 2.0ratios; this sample has mean (median) Ly-alpha equivalent width -1 (-4) A, and only 9% of these galaxies qualify as LAEs. The extreme galaxies typically have lower attenuation at Ly-alpha than those in the comparison sample, and have ~50% lower median oxygen abundances. Both factors are likely to facilitate the escape of Ly-alpha: in less dusty galaxies Ly-alpha photons are l...

  3. Spatial/temporal variations and source apportionment of VOCs monitored at community scale in an urban area.

    Science.gov (United States)

    Yu, Chang Ho; Zhu, Xianlei; Fan, Zhi-hua

    2014-01-01

    This study aimed to characterize spatial/temporal variations of ambient volatile organic compounds (VOCs) using a community-scale monitoring approach and identify the main sources of concern in Paterson, NJ, an urban area with mixed sources of VOCs. VOC samples were simultaneously collected from three local source-dominated (i.e., commercial, industrial, and mobile) sites in Paterson and one background site in Chester, NJ (located ∼58 km southwest of Paterson). Samples were collected using the EPA TO-15 method from midnight to midnight, one in every sixth day over one year. Among the 60 analyzed VOCs, ten VOCs (acetylene, benzene, dichloromethane, ethylbenzene, methyl ethyl ketone, styrene, toluene, m,p-xylene, o-xylene, and p-dichlorobenzene) were selected to examine their spatial/temporal variations. All of the 10 VOCs in Paterson were significantly higher than the background site (pp-xylene, o-xylene, and p-dichlorobenzene measured at the commercial site were significantly higher than the industrial/mobile sites (pp-dichlorobenzene) were significantly different by season (pp<0.05). These results are consistent with literature data, indicating the impact of anthropogenic VOC sources on air pollution in Paterson. Positive Matrix Factorization (PMF) analysis was applied for 24-hour integrated VOC measurements in Paterson over one year and identified six contributing factors, including motor vehicle exhausts (20%), solvents uses (19%), industrial emissions (16%), mobile+stationery sources (12%), small shop emissions (11%), and others (22%). Additional locational analysis confirmed the identified sources were well matched with point sources located upwind in Paterson. The study demonstrated the community-scale monitoring approach can capture spatial variation of VOCs in an urban community with mixed VOC sources. It also provided robust data to identify major sources of concern in the community.

  4. Evaluating a space-based indicator of surface ozone sensitivity to emissions of NOx vs. NMVOC over major northern mid-latitude source regions

    Science.gov (United States)

    Jin, X.; Fiore, A. M.; Murray, L. T.; Valin, L.

    2016-12-01

    Determining the most effective strategy for mitigating local surface ozone pollution requires knowledge of the relative ambient concentration of NOx to VOCs in the air. Satellite observations of the tropospheric column ratio of HCHO (a marker of VOCs) to NO2 (a marker of NOx) have been used as an indicator to identify areas which would benefit from reducing NOx emissions (NOx-sensitive, HCHO:NO2 > 2), and areas where reducing VOC emission leads to lower ozone (VOC-sensitive or NOx-saturated, HCHO:NO2 DOMINO, SP) products with GEOS-Chem simulations. The spatiotemporal correlation between the modeled and observed indicator ratio is mainly influenced by the choice of NO2 product, while the mean bias depends on the choice of HCHO product. Applying a regime classification method that adjusts these uncertainties, we investigate the decadal trend of surface ozone sensitivity from the space over the three regions. Some megacities (e.g., Chicago, New York, Guangzhou) show a clear transition from VOC-limited to NOx-limited ozone production regimes, resulting from emission control strategies over the past decade.

  5. Photoelectron Imaging of OXIDE.VOC Clusters

    Science.gov (United States)

    Patros, Kellyn M.; Mann, Jennifer; Chick Jarrold, Caroline

    2016-06-01

    Perturbations of the bare O2- and O4- electronic structure arising from VOC (VOC = hexane, isoprene, benzene and benzene.D6) interactions are investigated using anion photoelectron imaging at 2.33 and 3.49 eV photon energies. Trends observed from comparing features in the spectra include VOC-identity-dependent electron affinities of the VOC complexes relative to the bare oxide clusters, due to enhance stability in the anion complex relative to the neutral. Autodetachment is observed in all O4-.VOC spectra and only isoprene with O2-. In addition, the intensities of transitions to states correlated with the singlet states of O2 neutral via detachment from the O2-.VOC anion complexes show dramatic VOC-identity variations. Most notably, benzene as a complex partner significantly enhances these transitions relative to O2- and O2-.hexane. A less significant enhancement is also observed in the O2-.isoprene complex. This enhancement may be due to the presence of low-lying triplet states in the complex partners.

  6. [Evaluation and selection of VOCs treatment technologies in packaging and printing industry].

    Science.gov (United States)

    Wang, Hai-Lin; Wang, Jun-Hui; Zhu, Chun-Lei; Nie, Lei; Hao, Zheng-Ping

    2014-07-01

    Volatile organic compounds (VOCs) play an important role in urban air pollution. Activities of industries including the packaging and printing industries are regarded as the major sources. How to select the suitable treating techniques is the major problem for emission control. In this article, based on the VOCs emission characteristics of the packaging and printing industry and the existing treatment technologies, using the analytic hierarchy process (AHP) model, an evaluation system for VOCs selection was established and all the technologies used for treatment were assessed. It showed that the priority selection was in the following order: Carbon Fiber Adsorption-Desorption > Granular Carbon Adsorption-Desorption > Thermal Combustion > Regenerative Combustion > Catalytic combustion > Rotary adsorption-concentration and combustion > Granular Carbon adsorption-concentration and combustion. Carbon Fiber Adsorption-Desorption was selected as the best available technology due to its highest weight among those technologies.

  7. An Improved, Automated Whole-Air Sampler and VOC Analysis System: Results from SONGNEX 2015

    Science.gov (United States)

    Lerner, B. M.; Gilman, J.; Tokarek, T. W.; Peischl, J.; Koss, A.; Yuan, B.; Warneke, C.; Isaacman-VanWertz, G. A.; Sueper, D.; De Gouw, J. A.; Aikin, K. C.

    2015-12-01

    Accurate measurement of volatile organic compounds (VOCs) in the troposphere is critical for the understanding of emissions and physical and chemical processes that can impact both air quality and climate. Airborne VOC measurements have proven challenging due to the requirements of short sample collection times (=10 s) to maximize spatial resolution and sampling frequency and high sensitivity (pptv) to chemically diverse hydrocarbons, halocarbons, oxygen- and nitrogen-containing VOCs. NOAA ESRL CSD has built an improved whole air sampler (iWAS) which collects compressed ambient air samples in electropolished stainless steel canisters, based on the NCAR HAIS Advanced Whole Air Sampler [Atlas and Blake]. Post-flight chemical analysis is performed with a custom-built gas chromatograph-mass spectrometer system that pre-concentrates analyte cryostatically via a Stirling cooler, an electromechanical chiller which precludes the need for liquid nitrogen to reach trapping temperatures. For the 2015 Shale Oil and Natural Gas Nexus Study (SONGNEX), CSD conducted iWAS measurements on 19 flights aboard the NOAA WP-3D aircraft between March 19th and April 27th. Nine oil and natural gas production regions were surveyed during SONGNEX and more than 1500 air samples were collected and analyzed. For the first time, we employed real-time mapping of sample collection combined with live data from fast time-response measurements (e.g. ethane) for more uniform surveying and improved target plume sampling. Automated sample handling allowed for more than 90% of iWAS canisters to be analyzed within 96 hours of collection - for the second half of the campaign improved efficiencies reduced the median sample age at analysis to 36 hours. A new chromatography peak-fitting software package was developed to minimize data reduction time by an order of magnitude without a loss of precision or accuracy. Here we report mixing ratios for aliphatic and aromatic hydrocarbons (C2-C8) along with select

  8. Volatile organic compound (VOC) determination in working atmospheres; Determinacion de compuestos organicos volatiles (VOC) en ambiente laboral

    Energy Technology Data Exchange (ETDEWEB)

    Blass A, Georgina; Panama T, Luz A; Corrales C, Deyanira [Instituto de Investigaciones Electricas, Cuernavaca, Morelos (Mexico)

    2003-07-01

    The present work describes, in a synthesized way, the implementation and application of procedures based on the normativity related to the subject of the volatile organic compounds (Volatile Organic Compounds VOC), that allow to sample, quantify and evaluate the present contamination in the working atmosphere of a refinery due to the fugitive emissions of VOC and other substances. In accordance with the corresponding normativity, more than 189 organic compounds denominated dangerous air polluting agents (Hazardous Air Pollutants, HAP) can be found in a working atmosphere, but they are the 11 main HAP that can be found in a refinery. In the present article the work made for the sampling and quantification of 5 of the 11 dangerous polluting agents of the air: benzene, toluene, xylene, iso-octane and naphthalene. [Spanish] El presente trabajo describe, de manera sintetizada, la implementacion y aplicacion de procedimientos basados en la normatividad relacionada al tema de los compuestos organicos volatiles (Volatil Organic Compounds, VOC), que permiten muestrear, cuantificar y evaluar la contaminacion presente en el ambiente laboral de una refineria debido a las emisiones fugitivas de VOC y otras sustancias. De acuerdo con la normatividad correspondiente, mas de 189 compuestos organicos denominados contaminantes peligrosos del aire (Hazardous Air Pollutants, HAP), pueden ser encontrados en un ambiente laboral, pero son 11 los principales HAP que pueden ser hallados en una refineria. En el presente articulo se informa el trabajo realizado para el muestreo y cuantificacion de 5 de los 11 contaminantes peligrosos del aire: benceno, tolueno, xileno, iso-octano y naftaleno.

  9. Volatile Organic Compound (VOC Removal by Vapor Permeation at Low VOC Concentrations: Laboratory Scale Results and Modeling for Scale Up

    Directory of Open Access Journals (Sweden)

    Philippe Moulin

    2011-03-01

    Full Text Available Petroleum transformation industries have applied membrane processes for solvent and hydrocarbon recovery as an economic alternative to reduce their emissions and reuse evaporated components. Separation of the volatile organic compounds (VOCs (toluene-propylene-butadiene from air was performed using a poly dimethyl siloxane (PDMS/α-alumina membrane. The experimental set-up followed the constant pressure/variable flow set-up and was operated at ~21 °C. The membrane is held in a stainless steel module and has a separation area of 55 × 10−4 m². Feed stream was set to atmospheric pressure and permeate side to vacuum between 3 and 5 mbar. To determine the performance of the module, the removed fraction of VOC was analyzed by Gas Chromatography/Flame Ionization Detector (GC/FID. The separation of the binary, ternary and quaternary hydrocarbon mixtures from air was performed at different flow rates and more especially at low concentrations. The permeate flux, permeance, enrichment factor, separation efficiency and the recovery extent of the membrane were determined as a function of these operating conditions. The permeability coefficients and the permeate flux through the composite PDMS-alumina membrane follow the order given by the Hildebrand parameter: toluene > 1,3-butadiene > propylene. The simulated data for the binary VOC/air mixtures showed fairly good agreement with the experimental results in the case of 1,3-butadiene and propylene. The discrepancies observed for toluene permeation could be minimized by taking into account the effects of the porous support and an influence of the concentration polarization. Finally, the installation of a 0.02 m2 membrane module would reduce 95% of the VOC content introduced at real concentration conditions used in the oil industry.

  10. Volatile Organic Compound (VOC) Removal by Vapor Permeation at Low VOC Concentrations: Laboratory Scale Results and Modeling for Scale Up.

    Science.gov (United States)

    Rebollar-Perez, Georgette; Carretier, Emilie; Lesage, Nicolas; Moulin, Philippe

    2011-03-03

    Petroleum transformation industries have applied membrane processes for solvent and hydrocarbon recovery as an economic alternative to reduce their emissions and reuse evaporated components. Separation of the volatile organic compounds (VOCs) (toluene-propylene-butadiene) from air was performed using a poly dimethyl siloxane (PDMS)/α-alumina membrane. The experimental set-up followed the constant pressure/variable flow set-up and was operated at ~21 °C. The membrane is held in a stainless steel module and has a separation area of 55 × 10-4 m². Feed stream was set to atmospheric pressure and permeate side to vacuum between 3 and 5 mbar. To determine the performance of the module, the removed fraction of VOC was analyzed by Gas Chromatography/Flame Ionization Detector (GC/FID). The separation of the binary, ternary and quaternary hydrocarbon mixtures from air was performed at different flow rates and more especially at low concentrations. The permeate flux, permeance, enrichment factor, separation efficiency and the recovery extent of the membrane were determined as a function of these operating conditions. The permeability coefficients and the permeate flux through the composite PDMS-alumina membrane follow the order given by the Hildebrand parameter: toluene > 1,3-butadiene > propylene. The simulated data for the binary VOC/air mixtures showed fairly good agreement with the experimental results in the case of 1,3-butadiene and propylene. The discrepancies observed for toluene permeation could be minimized by taking into account the effects of the porous support and an influence of the concentration polarization. Finally, the installation of a 0.02 m2 membrane module would reduce 95% of the VOC content introduced at real concentration conditions used in the oil industry.

  11. Impact of Marcellus Shale natural gas development in southwest Pennsylvania on volatile organic compound emissions and regional air quality.

    Science.gov (United States)

    Swarthout, Robert F; Russo, Rachel S; Zhou, Yong; Miller, Brandon M; Mitchell, Brittney; Horsman, Emily; Lipsky, Eric; McCabe, David C; Baum, Ellen; Sive, Barkley C

    2015-03-03

    The Marcellus Shale is the largest natural gas deposit in the U.S. and rapid development of this resource has raised concerns about regional air pollution. A field campaign was conducted in the southwestern Pennsylvania region of the Marcellus Shale to investigate the impact of unconventional natural gas (UNG) production operations on regional air quality. Whole air samples were collected throughout an 8050 km(2) grid surrounding Pittsburgh and analyzed for methane, carbon dioxide, and C1-C10 volatile organic compounds (VOCs). Elevated mixing ratios of methane and C2-C8 alkanes were observed in areas with the highest density of UNG wells. Source apportionment was used to identify characteristic emission ratios for UNG sources, and results indicated that UNG emissions were responsible for the majority of mixing ratios of C2-C8 alkanes, but accounted for a small proportion of alkene and aromatic compounds. The VOC emissions from UNG operations accounted for 17 ± 19% of the regional kinetic hydroxyl radical reactivity of nonbiogenic VOCs suggesting that natural gas emissions may affect compliance with federal ozone standards. A first approximation of methane emissions from the study area of 10.0 ± 5.2 kg s(-1) provides a baseline for determining the efficacy of regulatory emission control efforts.

  12. Modeled and observed ozone sensitivity to mobile-source emissions in Mexico City

    Directory of Open Access Journals (Sweden)

    M. Zavala

    2009-01-01

    Full Text Available The emission characteristics of mobile sources in the Mexico City Metropolitan Area (MCMA have changed significantly over the past few decades in response to emission control policies, advancements in vehicle technologies and improvements in fuel quality, among others. Along with these changes, concurrent non-linear changes in photochemical levels and criteria pollutants have been observed, providing a unique opportunity to understand the effects of perturbations of mobile emission levels on the photochemistry in the region using observational and modeling approaches. The observed historical trends of ozone (O3, carbon monoxide (CO and nitrogen oxides (NOx suggest that ozone production in the MCMA has changed from a low to a high VOC-sensitive regime over a period of 20 years. Comparison of the historical emission trends of CO, NOx and hydrocarbons derived from mobile-source emission studies in the MCMA from 1991 to 2006 with the trends of the concentrations of CO, NOx, and the CO/NOx ratio during peak traffic hours also indicates that fuel-based fleet average emission factors have significantly decreased for CO and VOCs during this period whereas NOx emission factors do not show any strong trend, effectively reducing the ambient VOC/NOx ratio.

    This study presents the results of model analyses on the sensitivity of the observed ozone levels to the estimated historical changes in its precursors. The model sensitivity analyses used a well-validated base case simulation of a high pollution episode in the MCMA with the mathematical Decoupled Direct Method (DDM and the standard Brute Force Method (BFM in the 3-D CAMx chemical transport model. The model reproduces adequately the observed historical trends and current photochemical levels. Comparison of the BFM and the DDM sensitivity techniques indicates that the model yields ozone values that increase linearly with

  13. Modeled and observed ozone sensitivity to mobile-source emissions in Mexico City

    Directory of Open Access Journals (Sweden)

    M. Zavala

    2008-08-01

    Full Text Available The emission characteristics of mobile sources in the Mexico City Metropolitan Area (MCMA have changed significantly over the past few decades in response to emission control policies, advancements in vehicle technologies and improvements in fuel quality, among others. Along with these changes, concurrent non-linear changes in photochemical levels and criteria pollutants have been observed, providing a unique opportunity to understand the effects of perturbations of mobile emission levels on the photochemistry in the region using observational and modeling approaches. The observed historical trends of ozone (O3, carbon monoxide (CO and nitrogen oxides (NOx suggest that ozone production in the MCMA has changed from a low to a high VOC-sensitive regime over a period of 20 years. Comparison of the historical emission trends of CO, NOx and hydrocarbons derived from mobile-source emission studies in the MCMA from 1991 to 2006 with the trends of the concentrations of CO, NOx, and the CO/NOx ratio during peak traffic hours also indicates that fuel-based fleet average emission factors have significantly decreased for CO and VOCs during this period whereas NOx emission factors do not show any strong trend, effectively reducing the ambient VOC/NOx ratio.

    This study presents the results of model analyses on the sensitivity of the observed ozone levels to the estimated historical changes in its precursors. The model sensitivity analyses used a well-validated base case simulation of a high pollution episode in the MCMA with the mathematical Decoupled Direct Method (DDM and the standard Brute Force Method (BFM in the 3-D CAMx chemical transport model. The model reproduces adequately the observed historical trends and current photochemical levels. Comparison of the BFM and the DDM sensitivity techniques indicates that the model yields ozone values that increase linearly with

  14. Modeled and observed ozone sensitivity to mobile-source emissions in Mexico City

    Science.gov (United States)

    Zavala, M.; Lei, W.; Molina, M. J.; Molina, L. T.

    2009-01-01

    The emission characteristics of mobile sources in the Mexico City Metropolitan Area (MCMA) have changed significantly over the past few decades in response to emission control policies, advancements in vehicle technologies and improvements in fuel quality, among others. Along with these changes, concurrent non-linear changes in photochemical levels and criteria pollutants have been observed, providing a unique opportunity to understand the effects of perturbations of mobile emission levels on the photochemistry in the region using observational and modeling approaches. The observed historical trends of ozone (O3), carbon monoxide (CO) and nitrogen oxides (NOx) suggest that ozone production in the MCMA has changed from a low to a high VOC-sensitive regime over a period of 20 years. Comparison of the historical emission trends of CO, NOx and hydrocarbons derived from mobile-source emission studies in the MCMA from 1991 to 2006 with the trends of the concentrations of CO, NOx, and the CO/NOx ratio during peak traffic hours also indicates that fuel-based fleet average emission factors have significantly decreased for CO and VOCs during this period whereas NOx emission factors do not show any strong trend, effectively reducing the ambient VOC/NOx ratio. This study presents the results of model analyses on the sensitivity of the observed ozone levels to the estimated historical changes in its precursors. The model sensitivity analyses used a well-validated base case simulation of a high pollution episode in the MCMA with the mathematical Decoupled Direct Method (DDM) and the standard Brute Force Method (BFM) in the 3-D CAMx chemical transport model. The model reproduces adequately the observed historical trends and current photochemical levels. Comparison of the BFM and the DDM sensitivity techniques indicates that the model yields ozone values that increase linearly with NOx emission reductions and decrease linearly with VOC emission reductions only up to 30% from the

  15. Investigating Sources and Emissions of Volatile Organic Compounds in California's San Joaquin Valley

    Science.gov (United States)

    Gentner, D. R.; Harley, R. A.; Weber, R.; Karlik, J. F.; Goldstein, A. H.

    2011-12-01

    Emissions of Volatile Organic Compounds (VOCs) are regulated both as primary air pollutants and as precursors to the formation of secondary organic aerosol and tropospheric ozone. The San Joaquin Valley, a non-attainment area for ozone and PM2.5, contains a variety of point, area, and mobile VOC sources that contribute to both primary and secondary pollution. Using ambient measurements of over 100 different VOCs and Intermediate Volatility Organic Compounds (IVOCs) made at multiple field sites, we assess the magnitude and importance of various VOC sources in the San Joaquin Valley. Hourly measurements were made during the spring and summer of 2010 via in-situ gas chromatography in Bakersfield, CA as part of the CalNex experiment and also at a rural site located 100 km north of Bakersfield. Additionally, in-situ measurements of fresh motor vehicle exhaust were made in Oakland's Caldecott tunnel during the summer of 2010. Measurements include a broad array of anthropogenic and biogenic VOCs ranging in size from 1 to 17 carbon atoms, including many compounds with functional groups or substituents (e.g. aldehydes, ketones, alcohols, halogens, sulfur, & nitrogen). Using statistical methods of source apportionment, covariance, source receptor modeling, and air parcel back trajectories, we assess the impact of various sources on observed VOC concentrations at our field sites in the San Joaquin Valley. Prevalent sources include gasoline and diesel-vehicle exhaust, petroleum extraction/refining, biogenic emissions from agricultural crops and natural vegetation, and emissions from dairy operations and animal husbandry. We use measurements of fresh motor vehicle emissions from the Caldecott tunnel to constrain apportionment of gasoline and diesel-related VOCs and IVOCs in the San Joaquin Valley. Initial results from Bakersfield show substantial influence from local anthropogenic VOC sources, but there is evidence for transport of emissions from both anthropogenic and biogenic

  16. Mobile Emission Trends in the MCMA: Effects on Photochemistry

    Science.gov (United States)

    Zavala, M.; Herndon, S.; Wood, E.; Knighton, B.; Molina, M. J.; Kolb, C.; Molina, L. T.

    2007-05-01

    Emissions from mobile sources have a strong influence on the photochemical levels and other pollutants of an urban area. Mobile emissions in the Mexico City Metropolitan Area (MCMA) have been studied for the period 1991- 2006 with several measurement techniques that include remote sensing, dynamometer and tunnel studies and - more recently- with the chasing technique. During the same time period, several factors that directly affect the emission characteristics of the vehicle fleet have occurred. These factors include the implementation of more stringent emission standards, emission control technologies and changes in fuel composition, among others. Along with these changes, concurrent non-linear changes in photochemical levels as well as in toxic and criteria pollutants have been observed. In this study we compare the historical trends of CO, NOx and VOCs from mobile emission sources in the MCMA from 1991 to 2006 with pollutant trends of hourly data of CO, NOX, and the CO/NOX ratio during peak traffic. Using the historical trends comparison and the on-road emission data obtained with the Aerodyne Research Inc. (ARI) Mobile Laboratory during the 2002/2003-MCMA and the MCMA-2006/MILAGRO field campaigns (see http:www.mce2.org), we derive historical changes on the VOC/NOX ratio from mobile sources. The inferred trend is in turn compared with observed trends of O3 to quantify the induced changes on photochemical levels in the MCMA by mobile sources. Finally, the effect of the perturbed VOC/NOX ratio on simulated historical ozone levels is investigated in a companion modeling study.

  17. Effects of different influent C/N ratios on the performance of various earthworm eco-filter systems: nutrient removal and greenhouse gas emission.

    Science.gov (United States)

    Huang, Wei; Zhao, Yongjun; Wu, Jiangtao; Zhang, Jibiao; Zheng, Zheng

    2014-01-01

    In this study, we sought to identify influent carbon-to-nitrogen (C/N) ratios that yield relatively high nutrient removal efficiency with relatively low greenhouse gas (GHG) emissions. The earthworm eco-filter (EE) system, which is composed of earthworms and plants (EP group), was found to be optimal for maximizing nutrient removal while reducing GHG emissions. In this EE system, the optimal influent C/N ratio for nutrient removal and GHG emission under C2N treatment conditions. Nutrient removal efficiency under this condition was 85.19 ± 6.40% chemical oxygen demand, 71.99 ± 11.28% total nitrogen, and 77.91 ± 8.51% total phosphorus, while the CO2 emission rate was 678.89 ± 201.87 mg m(-2) h(-1). Moreover, the highest nutrient removal and GHG emission rates were both achieved in late summer (August). Thus, carbon variation, season, system variation, as well as synergistic interaction between system variations and seasons, significantly affect nutrient removal efficiencies and GHG emissions.

  18. Characterization of polycyclic aromatic hydrocarbon emissions in the particulate and gas phase from smoldering mosquito coils containing various atomic hydrogen/carbon ratios

    Energy Technology Data Exchange (ETDEWEB)

    Yang, Tzu-Ting, E-mail: d89844001@ntu.edu.tw [Department of Environmental Engineering and Health, Yuanpei University, No. 306, Yuanpei St., Hsin Chu 30015, Taiwan (China); Lin, Shaw-Tao [Department of Applied Chemistry, Providence University, No. 200 Chung-Chi Rd., Salu Dist., Taichung City 43301, Taiwan (China); Lin, Tser-Sheng [Department of Safety, Health, and Environmental Engineering, National United University, 2 Lien Da, Maioli 360, Taiwan (China); Chung, Hua-Yi [Department of Environmental Engineering and Health, Yuanpei University, No. 306, Yuanpei St., Hsin Chu 30015, Taiwan (China)

    2015-02-15

    The polycyclic aromatic hydrocarbon emissions in particulate and gas phases generated from smoldering mosquito coils containing various atomic H/C ratios were examined. Five types of mosquito coils were burned in a test chamber with a total airflow rate of 8.0 L/min at a constant relative humidity and temperature. The concentrations of individual PAHs were determined using the GC/MS technique. Among the used mosquito coils, the atomic H/C ratio ranged from 1.23 to 1.57, yielding total mass, gaseous, and particulate PAH emission factors of 28.17–78.72 mg/g, 26,139.80–35,932.98 and 5735.22–13,431.51 ng/g, respectively. The various partitions of PAHs in the gaseous and particulate phases were in the ranges, 70.26–83.70% and 16.30–29.74% for the utilized mosquito coils. The carcinogenic potency of PAH emissions in the particulate phase (203.82–797.76 ng/g) was approximately 6.92–25.08 times higher than that of the gaseous phase (26.27–36.07 ng/g). Based on the analyses of PAH emissions, mosquito coils containing the lowest H/C ratio, a low oxygen level, and additional additives (i.e., CaCO{sub 3}) are recommended for minimizing the production of total PAH emission factors and carcinogenic potency. - Highlights: • PAHs emissions are influenced by mosquito coils containing various atomic H/C ratios. • The PAHs generated by burning mosquito coils mainly occur in the gaseous phase. • Total TEQ emission factors of PAHs mainly consisted of the particulate phase (> 87%). • The BaP and BaA accounted for 71.13–77.28% of the total TEQ emission factors. • Special PAH ratios were regarded as characteristic ratios for burning mosquito coil.

  19. Low VOC Barrier Coating for Industrial Maintenance

    Science.gov (United States)

    2012-09-01

    Technology Certification Program HAP Hazardous Air Pollutant HW hazardous waste LVBC low VOC barrier coating MEK methyl ethyl ketone MIL-DTL...peeling, blistering , tape adhesion, pull-off adhesion, film thickness, and LVBC/ZVT patch test adhesion testing in an acceptable or better manner...significant reductions in the amount of hazardous waste generated by the Navy. The ZVT technology contains less than 5 g/l of VOC and the resulting

  20. Biomass burning emissions and potential air quality impacts of volatile organic compounds and other trace gases from fuels common in the US

    Science.gov (United States)

    Gilman, J. B.; Lerner, B. M.; Kuster, W. C.; Goldan, P. D.; Warneke, C.; Veres, P. R.; Roberts, J. M.; de Gouw, J. A.; Burling, I. R.; Yokelson, R. J.

    2015-12-01

    A comprehensive suite of instruments was used to quantify the emissions of over 200 organic gases, including methane and volatile organic compounds (VOCs), and 9 inorganic gases from 56 laboratory burns of 18 different biomass fuel types common in the southeastern, southwestern, or northern US. A gas chromatograph-mass spectrometry (GC-MS) instrument provided extensive chemical detail of discrete air samples collected during a laboratory burn and was complemented by real-time measurements of organic and inorganic species via an open-path Fourier transform infrared spectroscopy (OP-FTIR) instrument and three different chemical ionization-mass spectrometers. These measurements were conducted in February 2009 at the US Department of Agriculture's Fire Sciences Laboratory in Missoula, Montana and were used as the basis for a number of emission factors reported by Yokelson et al. (2013). The relative magnitude and composition of the gases emitted varied by individual fuel type and, more broadly, by the three geographic fuel regions being simulated. Discrete emission ratios relative to carbon monoxide (CO) were used to characterize the composition of gases emitted by mass; reactivity with the hydroxyl radical, OH; and potential secondary organic aerosol (SOA) precursors for the 3 different US fuel regions presented here. VOCs contributed less than 0.78 % ± 0.12 % of emissions by mole and less than 0.95 % × 0.07 % of emissions by mass (on average) due to the predominance of CO2, CO, CH4, and NOx emissions; however, VOCs contributed 70-90 (±16) % to OH reactivity and were the only measured gas-phase source of SOA precursors from combustion of biomass. Over 82 % of the VOC emissions by mole were unsaturated compounds including highly reactive alkenes and aromatics and photolabile oxygenated VOCs (OVOCs) such as formaldehyde. OVOCs contributed 57-68 % of the VOC mass emitted, 41-54 % of VOC-OH reactivity, and aromatic-OVOCs such as benzenediols, phenols, and benzaldehyde

  1. PROCEEDINGS: LOW- AND NO-VOC COATING TECHNOLOGIES - 2ND BIENNIAL INTERNATIONAL CONFERENCE

    Science.gov (United States)

    The report documents an international conference that provided a forum for the exchange of technical information on coating technologies. It focused on improved and emerging technologies that result in fewer volatile organic compound (VOC) and toxic air emissions that those from ...

  2. Influence of the overfire air ratio on the NO(x) emission and combustion characteristics of a down-fired 300-MW(e) utility boiler.

    Science.gov (United States)

    Ren, Feng; Li, Zhengqi; Chen, Zhichao; Fan, Subo; Liu, Guangkui

    2010-08-15

    Down-fired boilers used to burn low-volatile coals have high NO(x) emissions. To find a way of solving this problem, an overfire air (OFA) system was introduced on a 300 MW(e) down-fired boiler. Full-scale experiments were performed on this retrofitted boiler to explore the influence of the OFA ratio (the mass flux ratio of OFA to the total combustion air) on the combustion and NO(x) emission characteristics in the furnace. Measurements were taken of gas temperature distributions along the primary air and coal mixture flows, average gas temperatures along the furnace height, concentrations of gases such as O(2), CO, and NO(x) in the near-wall region and carbon content in the fly ash. Data were compared for five different OFA ratios. The results show that as the OFA ratio increases from 12% to 35%, the NO(x) emission decreases from 1308 to 966 mg/Nm(3) (at 6% O(2) dry) and the carbon content in the fly ash increases from 6.53% to 15.86%. Considering both the environmental and economic effect, 25% was chosen as the optimized OFA ratio.

  3. The molar H: Corg ratio of biochar is a key factor in mitigating N2O emissions from soil

    NARCIS (Netherlands)

    Cayuela, M.L.; Jeffery, S.L.; Zwieten, van L.

    2015-01-01

    A previously published meta-analysis of biochar impacts on soil N2O emissions by Cayuela et al. (2014) found a “grand mean” reduction in N2O emissions of 54 ± 6% following biochar application to soil. Here we update this analysis to include 26 additional manuscripts bringing the total to 56

  4. The molar H: Corg ratio of biochar is a key factor in mitigating N2O emissions from soil

    NARCIS (Netherlands)

    Cayuela, M.L.; Jeffery, S.L.; Zwieten, van L.

    2015-01-01

    A previously published meta-analysis of biochar impacts on soil N2O emissions by Cayuela et al. (2014) found a “grand mean” reduction in N2O emissions of 54 ± 6% following biochar application to soil. Here we update this analysis to include 26 additional manuscripts bringing the total to 56 articles

  5. Effects of forage-to-concentrate ratio and dietary fiber manipulation on gas emissions and olfactometry from manure of Holstein heifers.

    Science.gov (United States)

    Lascano, G J; Heinrichs, A J; Gary, R R; Topper, P A; Brandt, R C; Adviento-Borbe, A; Fabian, E E

    2015-03-01

    The objective of this experiment was to determine the effects of differing ratios of forage to concentrate (F:C) and fiber levels on odor and gas emissions from manure. Eight Holstein dairy heifers (362.45±4.53 d of age and 335.6±7.41 kg of body weight) were randomly assigned to a split-plot, 4×4 Latin square design (21-d periods) with F:C as the whole plot (20 or 80% forage) and fiber level as sub-plot (0, 20, 40, or 60% inclusion of corn stover). Gas concentration was determined using an infrared photoacoustic analyzer over a 24-h period using a steady-state flux chamber setup. Odorous air samples were collected from chamber headspace and evaluated by 6 human assessors using a forced-choice dynamic olfactometry technique. Emissions of CO2 were greater for the low than high concentrate diets, and no differences were observed for NH3 and CH4 emissions between F:C. Although F:C had no effect on NH3 emissions, as dietary fiber increased, a linear interaction with opposite effects was found for high and low concentrate diets. Nitrous oxide emissions were below minimum detectable levels. Neither F:C nor neutral detergent fiber level affected odor intensity. Odor emissions were successfully assessed, and manipulation of dietary fiber has the potential to influence CH4 and NH3 emissions.

  6. 挥发性有机化合物排污权交易有偿使用初始价格定价研究%Study on the Initial Pricing of Paying for the use of the VOCs Pollution Emission Rights

    Institute of Scientific and Technical Information of China (English)

    陈文韬; 邹海英; 余秋良

    2016-01-01

    Initial pricing of paying for the use of pollution emission rights is one of the key links and core technologies for the construction of emission trading market. This paper based on the research and analysis of the initial pricing method, points out the the rationality and feasibility of the recovery cost pricing method in actually. According to this pricing method, the initial price of VOCs in Shunde City, which as an example, was determined as 8000 yuan per ton by investigating the pollution control cost of the enterprises. Then on this basis, we provide the analysis of the economic impact of paid use emission rights both from the industry level and enterprise level in Shunde.%排污权有偿使用定价是排污权有偿使用和交易制度建设的关键环节与核心技术之一。本文在对排污权有偿使用初始价格核算方法研究分析的基础上,指出恢复成本法在实际定价中的合理性和可行性;并以广东省佛山市顺德区为例,根据企业成本调查结果,研究制定VOCs排污权有偿使用初始价格,从理论上初步拟定为8000元/吨,在此基础上从行业层面和企业层面分析顺德区排污权有偿使用的经济影响。

  7. Volatile Organic Compound Concentrations and Emission Rates in New Manufactured and Site-Built Houses

    Energy Technology Data Exchange (ETDEWEB)

    Armin Rudd

    2008-10-30

    This study was conducted with the primary objective of characterizing and comparing the airborne concentrations and the emission rates of total VOCs and selected individual VOCs, including formaldehyde, among a limited number of new manufactured and site-built houses.

  8. Measurements of Volatile Organic Compounds (VOCs) on Board of the Zeppelin NT during the PEGASOS Campaign in 2012

    Science.gov (United States)

    Jäger, Julia; Hofzumahaus, Andreas; Beck, Harry; Rohrer, Franz; Broch, Sebastian; Fuchs, Hendrik; Gomm, Sebastian; Holland, Frank; Lu, Keding; Kiendler-Scharr, Astrid; Mentel, Thomas; Rose, Bernhard; Wegener, Robert; Wahner, Andreas

    2013-04-01

    encompassing different emission regimes (anthropogenic and biogenic) in both the Netherlands and in Italy, and on the fate of VOCs in the nocturnal boundary layer. Third, we also present how the VOC concentrations relate to other substances such as CO, NOx, O3 and the OH reactivity. Especially the comparison of VOC Data with the measured OH reactivity will reveal more insight into the 'missing reactivity'. Acknowledgement: PEGASOS project funded by the European Commission under the Framework Program 7 (FP7-ENV-2010-265148)

  9. Biogenic VOC oxidation and organic aerosol formation in an urban nocturnal boundary layer: aircraft vertical profiles in Houston, TX

    Directory of Open Access Journals (Sweden)

    S. S. Brown

    2013-05-01

    Full Text Available Organic compounds are a large component of aerosol mass, but organic aerosol (OA sources remain poorly characterized. Recent model studies have suggested nighttime oxidation of biogenic hydrocarbons as a potentially large OA source, but analysis of field measurements to test these predictions is sparse. We present nighttime vertical profiles of nitrogen oxides, ozone, VOCs and aerosol composition measured during low approaches of the NOAA P-3 aircraft to airfields in Houston, TX. This region has large emissions of both biogenic hydrocarbons and nitrogen oxides. The latter serves as a source of the nitrate radical, NO3, a key nighttime oxidant. Biogenic VOCs (BVOC and urban pollutants were concentrated within the nocturnal boundary layer (NBL, which varied in depth from 100–400 m. Despite concentrated NOx at low altitude, ozone was never titrated to zero, resulting in rapid NO3 radical production rates of 0.2–2.7ppbv h-1 within the NBL. Monoterpenes and isoprene were frequently present within the NBL and underwent rapid oxidation (up to 1ppbv h−1, mainly by NO3 and to a lesser extent O3. Concurrent enhancement in organic and nitrate aerosol on several profiles was consistent with primary emissions and with secondary production from nighttime BVOC oxidation, with the latter equivalent to or slightly larger than the former. Ratios of organic aerosol to CO within the NBL ranged from 14 to 38 μg m−3 OA/ppmv CO. A box model simulation incorporating monoterpene emissions, oxidant formation rates and monoterpene SOA yields suggested overnight OA production of 0.5 to 9 μg m−3.

  10. Quantification of emissions due to the natural gas storage well-casing blowout at Aliso Canyon/SS-25 using tracer flux ratio methods.

    Science.gov (United States)

    Herndon, S. C.; Daube, C.; Jervis, D.; Yacovitch, T. I.; Roscioli, J. R.; Curry, J.; Nelson, D. D.; Knighton, W. B.

    2016-12-01

    The methane emission rate from the well blowout at Aliso Canyon Natural Gas Storage Facility in Porter Ranch, California was quantified using the tracer flux ratio method (TFR). Over 400 tracer plume transects were collected, each lasting 15-300 seconds, using instrumentation aboard a mobile platform on 25 days between December 21, 2015 and March 9, 2016. The leak rate from October 23rd to February 11th has been estimated here using a combination of our leak rate measurements (TFR) and the flight mass balance (FMB) data [Conley et al., 2016]. The TFR approach employed here is assessing only the leaks due to the SS-25 well blowout and excludes other possible emissions at the facility. By "calibrating" the FMB dataset, the leak rate is integrated from Oct 23rd to December 21th. The sum of the inferred inferred and measured meissions suggests a total leak burden of 86,022 ± 8,393 metric tons of CH4. The primary uncertainty in this value is due to the uncertainty in the emission rate prior to the beginning of the TFR quantification. The ethane to methane enhancement ratio observed downwind of the leak site is consistent with the content of ethane in the natural gas at this site and provides definitive evidence that the methane emission rate quantified via tracer flux ratio is not due to a nearby landfill or other potential biogenic sources.

  11. Predicting the emission of volatile organic compounds from silage systems

    Science.gov (United States)

    As a precursor to smog, emission of volatile organic compounds (VOCs) to the atmosphere is an environmental concern in some regions. The major VOC emission source from farms is silage, with emissions coming from the silo face, mixing wagon, and feed bunk. The major compounds emitted are alcohols wit...

  12. 40 CFR 52.2036 - 1990 base year emission inventory.

    Science.gov (United States)

    2010-07-01

    ...—Fairless Hills 1990 VOC and NOX emissions for six emission units (no. 3 blast furnace, no.1 open hearth.... 1 open hearth furnace are 6.9 TPY and 455.5 TPY, respectively. The VOC and NOX emissions from the...

  13. Reassessing the ratio of glyoxal to formaldehyde as an indicator of hydrocarbon precursor speciation

    Science.gov (United States)

    Kaiser, J.; Wolfe, G. M.; Min, K. E.; Brown, S. S.; Miller, C. C.; Jacob, D. J.; deGouw, J. A.; Graus, M.; Hanisco, T. F.; Holloway, J.; Peischl, J.; Pollack, I. B.; Ryerson, T. B.; Warneke, C.; Washenfelder, R. A.; Keutsch, F. N.

    2015-07-01

    The yield of formaldehyde (HCHO) and glyoxal (CHOCHO) from oxidation of volatile organic compounds (VOCs) depends on precursor VOC structure and the concentration of NOx (NOx = NO + NO2). Previous work has proposed that the ratio of CHOCHO to HCHO (RGF) can be used as an indicator of precursor VOC speciation, and absolute concentrations of the CHOCHO and HCHO as indicators of NOx. Because this metric is measurable by satellite, it is potentially useful on a global scale; however, absolute values and trends in RGF have differed between satellite and ground-based observations. To investigate potential causes of previous discrepancies and the usefulness of this ratio, we present measurements of CHOCHO and HCHO over the southeastern United States (SE US) from the 2013 SENEX (Southeast Nexus) flight campaign, and compare these measurements with OMI (Ozone Monitoring Instrument) satellite retrievals. High time-resolution flight measurements show that high RGF is associated with monoterpene emissions, low RGF is associated with isoprene oxidation, and emissions associated with oil and gas production can lead to small-scale variation in regional RGF. During the summertime in the SE US, RGF is not a reliable diagnostic of anthropogenic VOC emissions, as HCHO and CHOCHO production are dominated by isoprene oxidation. Our results show that the new CHOCHO retrieval algorithm reduces the previous disagreement between satellite and in situ RGF observations. As the absolute values and trends in RGF observed during SENEX are largely reproduced by OMI observations, we conclude that satellite-based observations of RGF can be used alongside knowledge of land use as a global diagnostic of dominant hydrocarbon speciation.

  14. VOCs in Arid soils: Technology summary

    Energy Technology Data Exchange (ETDEWEB)

    1994-02-01

    The Volatile Organic Compounds In Arid Soils Integrated Demonstration (VOC-Arid ID) focuses on technologies to clean up volatile organic compounds and associated contaminants in soil and groundwater at arid sites. The initial host site is the 200 West Area at DOE`s Hanford site in southeastern Washington state. The primary VOC contaminant is carbon tetrachloride, in association with heavy metals and radionuclides. An estimated 580--920 metric tons of carbon tetrachloride were disposed of between 1955 and 1973, resulting in extensive soil and groundwater contamination. The VOC-Arid ID schedule has been divided into three phases of implementation. The phased approach provides for: rapid transfer of technologies to the Environmental Restoration (EM-40) programs once demonstrated; logical progression in the complexity of demonstrations based on improved understanding of the VOC problem; and leveraging of the host site EM-40 activities to reduce the overall cost of the demonstrations. During FY92 and FY93, the primary technology demonstrations within the ID were leveraged with an ongoing expedited response action at the Hanford 200 West Area, which is directed at vapor extraction of VOCs from the vadose (unsaturated) zone. Demonstration efforts are underway in the areas of subsurface characterization including: drilling and access improvements, off-gas and borehole monitoring of vadose zone VOC concentrations to aid in soil vapor extraction performance evaluation, and treatment of VOC-contaminated off-gas. These current demonstration efforts constitute Phase 1 of the ID and, because of the ongoing vadose zone ERA, can result in immediate transfer of successful technologies to EM-40.

  15. The ultraviolet emission properties of five low-redshift active galactic nuclei at high signal-to-noise ratio and spectral resolution

    Science.gov (United States)

    Laor, Ari; Bahcall, John N.; Jannuzi, Buell T.; Schneider, Donald P.; Green, Richard F.; Hartig, George F.

    1994-01-01

    We analyze the ultraviolet (UV) emission line and continuum properties of five low-redshift active galactic nuclei (four luminous quasars: PKS 0405-123, H1821 + 643, PG 0953 + 414, and 3C 273, and one bright Seyfert 1 galaxy: Mrk 205). The HST spectra have higher signal-to-noise ratios (typically approximately 60 per resolution element) and spectral resolution (R = 1300) than all previously published UV spectra used to study the emission characteristics of active galactic nuclei. We include in the analysis ground-based optical spectra covering H beta and the narrow (O III) lambda lambda 4959, 5007 doublet. New results are obtained and presented.

  16. Summit CO2 emission rates by the CO2/SO2 ratio method at Kīlauea Volcano, Hawaiʻi, during a period of sustained inflation

    Science.gov (United States)

    Hager, S.A.; Gerlach, T.M.; Wallace, P.J.

    2008-01-01

    The emission rate of carbon dioxide escaping from the summit of Kīlauea Volcano, Hawaiʻi, proved highly variable, averaging 4900 ± 2000 metric tons per day (t/d) in June–July 2003 during a period of summit inflation. These results were obtained by combining over 90 measurements of COSPEC-derived SO2emission rates with synchronous CO2/SO2 ratios of the volcanic gas plume along the summit COSPEC traverse. The results are lower than the CO2 emission rate of 8500 ± 300 t/d measured by the same method in 1995–1999 during a period of long-term summit deflation [Gerlach, T.M., McGee, K.A., Elias, T., Sutton, A.J. and Doukas, M.P., 2002. Carbon dioxide emission rate of Kīlauea Volcano: Implications for primary magma and the summit reservoir. Journal of Geophysical Research-Solid Earth, 107(B9): art. no.-2189.]. Analysis of the data indicates that the emission rates of the present study likely reflect changes in the magma supply rate and residence time in the summit reservoir. It is also likely that emission rates during the inflation period were heavily influenced by SO2 pulses emitted adjacent to the COSPEC traverse, which biased CO2/SO2 ratios towards low values that may be unrepresentative of the global summit gas plume. We conclude that the SO2 pulses are consequences of summit re-inflation under way since 2003 and that CO2 emission rates remain comparable to, but more variable than, those measured prior to re-inflation.

  17. Effect of forage-to-concentrate ratio in dairy cow diets on emission of methane, carbon dioxide, and ammonia, lactation performance, and manure excretion.

    Science.gov (United States)

    Aguerre, M J; Wattiaux, M A; Powell, J M; Broderick, G A; Arndt, C

    2011-06-01

    Holstein cows housed in a modified tie-stall barn were used to determine the effect of feeding diets with different forage-to-concentrate ratios (F:C) on performance and emission of CH(4), CO(2) and manure NH(3)-N. Eight multiparous cows (means ± standard deviation): 620 ± 68 kg of body weight; 52 ± 34 d in milk and 8 primiparous cows (546 ± 38 kg of body weight; 93 ± 39 d in milk) were randomly assigned to 1 of 4 air-flow controlled chambers, constructed to fit 4 cows each. Chambers were assigned to dietary treatment sequences in a single 4 × 4 Latin square design. Dietary treatments, fed as 16.2% crude protein total mixed rations included the following F:C ratio: 47:53, 54:46, 61:39, and 68:32 [diet dry matter (DM) basis]. Forage consisted of alfalfa silage and corn silage in a 1:1 ratio. Cow performance and emission data were measured on the last 7 d and the last 4 d, respectively of each 21-d period. Air samples entering and exiting each chamber were analyzed with a photo-acoustic field gas monitor. In a companion study, fermentation pattern was studied in 8 rumen-cannulated cows. Increasing F:C ratio in the diet had no effect on DM intake (21.1 ± 1.5 kg/d), energy-corrected milk (ECM, 37.4 ± 2.2 kg/d), ECM/DM intake (1.81 ± 0.18), yield of milk fat, and manure excretion and composition; however, it increased milk fat content linearly by 7% and decreased linearly true protein, lactose, and solids-not-fat content (by 4, 1, and 2%, respectively) and yield (by 10, 6, and 6%, respectively), and milk N-to-N intake ratio. On average 93% of the N consumed by the cows in the chambers was accounted for as milk N, manure N, or emitted NH(3)-N. Increasing the F:C ratio also increased ruminal pH linearly and affected concentrations of butyrate and isovalerate quadratically. Increasing the F:C ratio from 47:53 to 68:32 increased CH(4) emission from 538 to 648 g/cow per day, but had no effect on manure NH(3)-N emission (14.1 ± 3.9 g/cow per day) and CO(2) emission

  18. The impact of speciated VOCs on regional ozone increment derived from measurements at the UK EMEP supersites between 1999 and 2012

    Directory of Open Access Journals (Sweden)

    C. S. Malley

    2015-03-01

    Full Text Available The impact of 27 volatile organic compounds (VOC on the regional O3 increment was investigated using measurements made at the UK EMEP supersites Harwell (1999–2001 and 2010–2012 and Auchencorth (2012. Ozone at these sites is representative of rural O3 in south-east England and northern UK, respectively. Monthly-diurnal regional O3 increment was defined as the difference between the regional and hemispheric background O3 concentrations, respectively derived from oxidant vs. NOx correlation plots, and cluster analysis of back trajectories arriving at Mace Head, Ireland. At Harwell, which had substantially greater regional ozone increments than at Auchencorth, variation in the regional O3 increment mirrored afternoon depletion of VOCs due to photochemistry (after accounting for diurnal changes in boundary layer mixing depth, and weighting VOC concentrations according to their photochemical ozone creation potential. A positive regional O3 increment occurred consistently during the summer, during which time afternoon photochemical depletion was calculated for the majority of measured VOCs, and to the greatest extent for ethene and m + p-xylene. This indicates that, of the measured VOCs, ethene and m + p-xylene emissions reduction would be most effective in reducing the regional O3 increment, but that reductions in a larger number of VOCs would be required for further improvement. The VOC diurnal photochemical depletion was linked to the sources of the VOC emissions through the integration of gridded VOC emissions estimates over 96 h air-mass back trajectories. This demonstrated that the effectiveness of VOC gridded emissions for use in measurement and modelling studies is limited by the highly aggregated nature of the 11 SNAP source sectors in which they are reported, as monthly variation in speciated VOC trajectory emissions did not reflect monthly changes in individual VOC diurnal photochemical depletion. Additionally, the major VOC emission

  19. SDSS-IV MaNGA: the impact of diffuse ionized gas on emission-line ratios, interpretation of diagnostic diagrams and gas metallicity measurements

    Science.gov (United States)

    Zhang, Kai; Yan, Renbin; Bundy, Kevin; Bershady, Matthew; Haffner, L. Matthew; Walterbos, René; Maiolino, Roberto; Tremonti, Christy; Thomas, Daniel; Drory, Niv; Jones, Amy; Belfiore, Francesco; Sánchez, Sebastian F.; Diamond-Stanic, Aleksandar M.; Bizyaev, Dmitry; Nitschelm, Christian; Andrews, Brett; Brinkmann, Jon; Brownstein, Joel R.; Cheung, Edmond; Li, Cheng; Law, David R.; Roman Lopes, Alexandre; Oravetz, Daniel; Pan, Kaike; Storchi Bergmann, Thaisa; Simmons, Audrey

    2017-04-01

    Diffuse ionized gas (DIG) is prevalent in star-forming galaxies. Using a sample of 365 nearly face-on star-forming galaxies observed by Mapping Nearby Galaxies at APO, we demonstrate how DIG in star-forming galaxies impacts the measurements of emission-line ratios, hence the interpretation of diagnostic diagrams and gas-phase metallicity measurements. At fixed metallicity, DIG-dominated low ΣHα regions display enhanced [S II]/Hα, [N II]/Hα, [O II]/Hβ and [O I]/Hα. The gradients in these line ratios are determined by metallicity gradients and ΣHα. In line ratio diagnostic diagrams, contamination by DIG moves H II regions towards composite or low-ionization nuclear emission-line region (LI(N)ER)-like regions. A harder ionizing spectrum is needed to explain DIG line ratios. Leaky H II region models can only shift line ratios slightly relative to H II region models, and thus fail to explain the composite/LI(N)ER line ratios displayed by DIG. Our result favours ionization by evolved stars as a major ionization source for DIG with LI(N)ER-like emission. DIG can significantly bias the measurement of gas metallicity and metallicity gradients derived using strong-line methods. Metallicities derived using N2O2 are optimal because they exhibit the smallest bias and error. Using O3N2, R23, N2 = [N II]/Hα and N2S2Hα to derive metallicities introduces bias in the derived metallicity gradients as large as the gradient itself. The strong-line method of Blanc et al. (IZI hereafter) cannot be applied to DIG to get an accurate metallicity because it currently contains only H II region models that fail to describe the DIG.

  20. A Coherent Study of Emission Lines from Broad-Band Photometry: Specific Star-Formation Rates and [OIII]/H{\\beta} Ratio at 3 < z < 6

    CERN Document Server

    Faisst, A L; Hsieh, B C; Laigle, C; Salvato, M; Tasca, L; Cassata, P; Davidzon, I; Ilbert, O; Fevre, O Le; Masters, D; McCracken, H J; Steinhardt, C; Silverman, J D; De Barros, S; Hasinger, G; Scoville, N Z

    2016-01-01

    We measure the H{\\alpha} and [OIII] emission line properties as well as specific star-formation rates (sSFR) of spectroscopically confirmed 33 cannot be fully explained in a picture of cold accretion driven growth. We find a progressively increasing [OIII]{\\lambda}5007/H{\\beta} ratio out to z~6, consistent with the ratios in local galaxies selected by increasing H{\\alpha} EW (i.e., sSFR). This demonstrates the potential of using "local high-z analogs" to investigate the spectroscopic properties and relations of galaxies in the re-ionization epoch.

  1. Release of VOCs and particles during use of nanofilm spray products.

    Science.gov (United States)

    Nørgaard, Asger W; Jensen, Keld A; Janfelt, Christian; Lauritsen, Frants R; Clausen, Per A; Wolkoff, Peder

    2009-10-15

    Here, we present emission data on VOCs and particles emitted during simulated use of four commercial nanofilm spray products (NFPs) used for making easy-to-clean or self-cleaning surfaces on floors, ceramic tiles, and windows. The aim was to characterize the emitted VOCs and to provide specific source strength data for VOCs and particles released to the airduring use of the products. Containers with NFP were mounted on a spray-stand inside a closed stainless steel chamber with no air exchange. NFPs were sprayed in amounts corresponding to 1 m2 surface toward a target plate at a distance of 35 cm. Released VOCs were measured by a combination of air sampling on Tenax TA adsorbent followed by thermal desorption GC/MS and GC/FID analysis and real time measurements using a miniature membrane inlet mass spectrometer. Particles were measured using a fast mobility particle sizer and an aerosol particle sizer. A number of VOCs were identified, including small alcohols, ketones and ethers, chlorinated acetones, a perfluorinated silane, limonene, and cyclic siloxanes. The number of generated particles was on the order of 3 x 10(8) to 2 x 10(10) particles/m3 per g sprayed NFP and were dominated by nanosize particles.

  2. Volcanic SO2 and SiF4 visualization using 2-D thermal emission spectroscopy – Part 1: Slant-columns and their ratios

    Directory of Open Access Journals (Sweden)

    M. Grutter

    2012-02-01

    Full Text Available The composition and emission rates of volcanic gas plumes provide insight of the geologic internal activity, atmospheric chemistry, aerosol formation and radiative processes around it. Observations are necessary for public security and the aviation industry. Ground-based thermal emission infrared spectroscopy, which uses the radiation of the volcanic gas itself, allows for continuously monitoring during day and night from a safe distance. We present measurements on Popocatépetl volcano based on thermal emission spectroscopy during different campaigns between 2006–2009 using a Scanning Infrared Gas Imaging System (SIGIS. The experimental set-up, measurement geometries and analytical algorithms are described. The equipment was operated from a safe distance of 12 km from the volcano at two different spectral resolutions: 0.5 and 4 cm−1. The 2-dimensional scanning capability of the instrument allows for an on-line visualization of the volcanic SO2 plume and its animation. SiF4 was also identified in the infrared spectra recorded at both resolutions. The SiF4/SO2 molecular ratio can be calculated from each image and used as a highly useful parameter to follow changes in volcanic activity. A small Vulcanian eruption was monitored during the night of 16 to 17 November 2008 and strong ash emission together with a pronounced SO2 cloud was registered around 01:00 a.m. LST (Local Standard Time. Enhanced SiF4/SO2 ratios were observed before and after the eruption. A validation of the results from thermal emission measurements with those from absorption spectra of the moon taken at the same time, as well as an error analysis, are presented. The inferred propagation speed from sequential images is used in a subsequent paper (Part 2 to calculate the emission rates at different distances from the crater.

  3. Volcanic SO2 and SiF4 visualization using 2-D thermal emission spectroscopy - Part 1: Slant-columns and their ratios

    Science.gov (United States)

    Stremme, W.; Krueger, A.; Harig, R.; Grutter, M.

    2012-02-01

    The composition and emission rates of volcanic gas plumes provide insight of the geologic internal activity, atmospheric chemistry, aerosol formation and radiative processes around it. Observations are necessary for public security and the aviation industry. Ground-based thermal emission infrared spectroscopy, which uses the radiation of the volcanic gas itself, allows for continuously monitoring during day and night from a safe distance. We present measurements on Popocatépetl volcano based on thermal emission spectroscopy during different campaigns between 2006-2009 using a Scanning Infrared Gas Imaging System (SIGIS). The experimental set-up, measurement geometries and analytical algorithms are described. The equipment was operated from a safe distance of 12 km from the volcano at two different spectral resolutions: 0.5 and 4 cm-1. The 2-dimensional scanning capability of the instrument allows for an on-line visualization of the volcanic SO2 plume and its animation. SiF4 was also identified in the infrared spectra recorded at both resolutions. The SiF4/SO2 molecular ratio can be calculated from each image and used as a highly useful parameter to follow changes in volcanic activity. A small Vulcanian eruption was monitored during the night of 16 to 17 November 2008 and strong ash emission together with a pronounced SO2 cloud was registered around 01:00 a.m. LST (Local Standard Time). Enhanced SiF4/SO2 ratios were observed before and after the eruption. A validation of the results from thermal emission measurements with those from absorption spectra of the moon taken at the same time, as well as an error analysis, are presented. The inferred propagation speed from sequential images is used in a subsequent paper (Part 2) to calculate the emission rates at different distances from the crater.

  4. Emissions of ammonia, nitrous oxide, methane, and carbon dioxide during storage of dairy cow manure as affected by dietary forage-to-concentrate ratio and crust formation.

    Science.gov (United States)

    Aguerre, M J; Wattiaux, M A; Powell, J M

    2012-12-01

    Sixteen 200-L barrels were used to determine the effects of dietary forage-to-concentrate (F:C) ratio on the rate of NH(3)-N, N(2)O, CH(4), and CO(2) emissions from dairy manure during a 77-d storage period. Manure was obtained from a companion study where cows were assigned to total mixed rations that included the following F:C ratio: 47:53, 54:46, 61:39, and 68:32 (diet dry matter basis) and housed in air-flow-controlled chambers constructed in a modified tiestall barn. On d 0 of this study, deposited manure and bedding from each emission chamber was thoroughly mixed, diluted with water (1.9 to 1 manure-to-water ratio) and loaded in barrels. In addition, on d 0, 7, 14, 28, 35, 49, 56, 63, 70, and 77 of storage, the rate of NH(3)-N, N(2)O, CH(4), and CO(2) emissions from each barrel were measured with a dynamic chamber and gas concentration measured with a photo-acoustic multi-gas monitor. Data were analyzed as a randomized complete block with 4 replications. Dietary F:C ratio had no effect on manure dry matter, total N and total ammoniacal-N (NH(3)-N + NH(4)(+)-N), or pH at the time of storage (mean ± SD: 10.6±0.6%, 3.0±0.2%, 93.1±18.1 mg/dL, and 7.8±0.5, respectively). No treatment differences were observed in the overall rate of manure NH(3)-N, N(2)O, CH(4), and CO(2) emissions (mean ± SD over the 77-d storage period; 117±25, 30±7, 299±62, and 15,396±753 mg/hr per m(2), respectively). The presence of straw bedding in manure promoted the formation of a surface crust that became air dried after about 1 mo of storage, and was associated with an altered pattern in NH(3)-N and N(2)O emissions in particular. Whereas NH(3)-N emission rate was highest on d 0 and gradually decreased until reaching negligible levels on d 35, N(2)O emission rate was almost zero the first 2 wk of storage, increased sharply to peak on d 35, and decreased subsequently. The emission rate of CH(4) and CO(2) peaked simultaneously on d 7, but decreased subsequently until the end of the

  5. Chlorinated volatile organic compounds (Cl-VOCs) in environment - sources, potential human health impacts, and current remediation technologies.

    Science.gov (United States)

    Huang, Binbin; Lei, Chao; Wei, Chaohai; Zeng, Guangming

    2014-10-01

    Chlorinated volatile organic compounds (Cl-VOCs), including polychloromethanes, polychloroethanes and polychloroethylenes, are widely used as solvents, degreasing agents and a variety of commercial products. These compounds belong to a group of ubiquitous contaminants that can be found in contaminated soil, air and any kind of fluvial mediums such as groundwater, rivers and lakes. This review presents a summary of the research concerning the production levels and sources of Cl-VOCs, their potential impacts on human health as well as state-of-the-art remediation technologies. Important sources of Cl-VOCs principally include the emissions from industrial processes, the consumption of Cl-VOC-containing products, the disinfection process, as well as improper storage and disposal methods. Human exposure to Cl-VOCs can occur through different routes, including ingestion, inhalation and dermal contact. The toxicological impacts of these compounds have been carefully assessed, and the results demonstrate the potential associations of cancer incidence with exposure to Cl-VOCs. Most Cl-VOCs thus have been listed as priority pollutants by the Ministry of Environmental Protection (MEP) of China, Environmental Protection Agency of the U.S. (U.S. EPA) and European Commission (EC), and are under close monitor and strict control. Yet, more efforts will be put into the epidemiological studies for the risk of human exposure to Cl-VOCs and the exposure level measurements in contaminated sites in the future. State-of-the-art remediation technologies for Cl-VOCs employ non-destructive methods and destructive methods (e.g. thermal incineration, phytoremediation, biodegradation, advanced oxidation processes (AOPs) and reductive dechlorination), whose advantages, drawbacks and future developments are thoroughly discussed in the later sections.

  6. The impact from emitted NO{sub x} and VOC in an aircraft plume. Model results for the free troposphere

    Energy Technology Data Exchange (ETDEWEB)

    Pleijel, K.

    1998-04-01

    The chemical fate of gaseous species in a specific aircraft plume is investigated using an expanding box model. The model treats the gas phase chemical reactions in detail, while other parameters are subject to a high degree of simplification. Model simulations were carried out in a plume up to an age of three days. The role of emitted VOC, NO{sub x} and CO as well as of background concentrations of VOC, NO{sub x} and ozone on aircraft plume chemistry was investigated. Background concentrations were varied in a span of measured values in the free troposphere. High background concentrations of VOC were found to double the average plume production of ozone and organic nitrates. In a high NO{sub x} environment the plume production of ozone and organic nitrates decreased by around 50%. The production of nitric acid was found to be less sensitive to background concentrations of VOC, and increased by up to 50% in a high NO{sub x} environment. Mainly, emitted NO{sub x} caused the plume production of ozone, nitric acid and organic nitrates. The ozone production during the first hours is determined by the relative amount of NO{sub 2} in the NO{sub x} emissions. The impact from emitted VOC was in relative values up to 20% of the ozone production and 65% of the production of organic nitrates. The strongest relative influence from VOC was found in an environment characterized by low VOC and high NO{sub x} background concentrations, where the absolute peak production was lower than in the other scenarios. The effect from emitting VOC and NO{sub x} at the same time added around 5% for ozone, 15% for nitric acid and 10% for organic nitrates to the plume production caused by NO{sub x} and VOC when emitted separately 47 refs, 15 figs, 4 tabs

  7. Effect of digestibility of grass-clover silage and concentrate to forage ratio on methane emission from dairy cows

    DEFF Research Database (Denmark)

    Hellwing, Anne Louise Frydendahl; Weisbjerg, Martin Riis

    and D, respectively. TMR forage DM consisted of 2/3 of one of the respective grass-clover silages and 1/3 maize silage, and concentrate (soya meal and wheat) proportion of DM was 20% (low) or 50% (high). Methane emissions from the cows were measured 20-22 hours in one of four chambers working after...

  8. Effect of digestibility of grass-clover silage and concentrate to forage ratio on methane emission from dairy cows

    DEFF Research Database (Denmark)

    Hellwing, Anne Louise Frydendahl; Weisbjerg, Martin Riis

    and D, respectively. TMR forage DM consisted of 2/3 of one of the respective grass-clover silages and 1/3 maize silage, and concentrate (soya meal and wheat) proportion of DM was 20% (low) or 50% (high). Methane emissions from the cows were measured 20-22 hours in one of four chambers working after...

  9. Time delay and excitation mode induced tunable red/near-infrared to green emission ratio of Er doped BiOCl

    Science.gov (United States)

    Avram, Daniel; Florea, Mihaela; Tiseanu, Ion; Tiseanu, Carmen

    2015-09-01

    Herein, we report on the emission color tunability of Er doped BiOCl measured under up—conversion as well as x-ray excitation modes. The dependence of red (670 nm) to green emission (543 nm) ratio on Er concentration (1 and 5%), excitation wavelength into different (656.4, 802 and 976 nm) or across single Er absorption levels (965 ÷ 990 nm) and delay after the laser pulse (0.001 ÷ 1 ms) is discussed in terms of ground state absorption/excited state absorption and energy transfer up-conversion mechanisms. A first example of extended Er x-ray emission measured in the range of 500 to 1700 nm shows comparable emission intensities corresponding to 543 nm and 1500 nm based transitions. The present results together with our earlier report on the upconversion emission of Er doped BiOCl excited at 1500 nm, suggest that Er doped BiOCl may be considered an attractive system for optical and x-ray imaging applications.

  10. A comparative study of fungal and bacterial biofiltration treating a VOC mixture

    Energy Technology Data Exchange (ETDEWEB)

    Estrada, José M. [Departamento de Procesos y Tecnología, Universidad Autónoma Metropolitana-Cuajimalpa, Artificios 40, Col. Miguel Hidalgo, Delegación Álvaro Obregón (Mexico); Departamento de Ingeniería Química y Tecnología del Medio Ambiente – Universidad de Valladolid, Valladolid (Spain); Hernández, Sergio [Departmento de Procesos e Hidráulica – Universidad Autónoma Metropolitana – Iztapalapa Mexico D.F. Mexico (Mexico); Muñoz, Raúl [Departamento de Ingeniería Química y Tecnología del Medio Ambiente – Universidad de Valladolid, Valladolid (Spain); Revah, Sergio, E-mail: srevah@xanum.uam.mx [Departamento de Procesos y Tecnología, Universidad Autónoma Metropolitana-Cuajimalpa, Artificios 40, Col. Miguel Hidalgo, Delegación Álvaro Obregón (Mexico)

    2013-04-15

    Highlights: ► Bacterial biofilter showed better EC and ΔP than fungal biofilter. ► The preferential biodegradation order was: propanal > hexanol > MIBK > toluene. ► Propanal partially inhibited the biodegradation of the rest of VOCs. ► The two-stage biofilter showed a higher stability than the individual units. -- Abstract: Bacterial biofilters usually exhibit a high microbial diversity and robustness, while fungal biofilters have been claimed to better withstand low moisture contents and pH values, and to be more efficient coping with hydrophobic volatile organic compounds (VOCs). However, there are only few systematic evaluations of both biofiltration technologies. The present study compared fungal and bacterial biofiltration for the treatment of a VOC mixture (propanal, methyl isobutyl ketone-MIBK, toluene and hexanol) under the same operating conditions. Overall, fungal biofiltration supported lower elimination capacities than its bacterial counterpart (27.7 ± 8.9 vs 40.2 ± 5.4 g C m{sup −3} reactor h{sup −1}), which exhibited a final pressure drop 60% higher than that of the bacterial biofilter due to mycelial growth. The VOC mineralization ratio was also higher in the bacterial bed (≈63% vs ≈43%). However, the substrate biodegradation preference order was similar for both biofilters (propanal > hexanol > MIBK > toluene) with propanal partially inhibiting the consumption of the rest of the VOCs. Both systems supported an excellent robustness versus 24 h VOC starvation episodes. The implementation of a fungal/bacterial coupled system did not significantly improve the VOC removal performance compared to the individual biofilter performances.

  11. Do vehicular emissions dominate the source of C6-C8 aromatics in the megacity Shanghai of eastern China?

    Science.gov (United States)

    Wang, Hongli; Wang, Qian; Chen, Jianmin; Chen, Changhong; Huang, Cheng; Qiao, Liping; Lou, Shengrong; Lu, Jun

    2015-01-01

    The characteristic ratios of volatile organic compounds (VOCs) to i-pentane, the indicator of vehicular emissions, were employed to apportion the vehicular and non-vehicular contributions to reactive species in urban Shanghai. Two kinds of tunnel experiments, one tunnel with more than 90% light duty gasoline vehicles and the other with more than 60% light duty diesel vehicles, were carried out to study the characteristic ratios of vehicle-related emissions from December 2009 to January 2010. Based on the experiments, the characteristic ratios of C6-C8 aromatics to i-pentane of vehicular emissions were 0.53 ± 0.08 (benzene), 0.70 ± 0.12 (toluene), 0.41 ± 0.09 (m,p-xylenes), 0.16 ± 0.04 (o-xylene), 0.023 ± 0.011 (styrene), and 0.15 ± 0.02 (ethylbenzene), respectively. The source apportionment results showed that around 23.3% of C6-C8 aromatics in urban Shanghai were from vehicular emissions, which meant that the non-vehicular emissions had more importance. These findings suggested that emission control of non-vehicular sources, i.e. industrial emissions, should also receive attention in addition to the control of vehicle-related emissions in Shanghai. The chemical removal of VOCs during the transport from emissions to the receptor site had a large impact on the apportionment results. Generally, the overestimation of vehicular contributions would occur when the VOC reaction rate constant with OH radicals (kOH) was larger than that of the vehicular indicator, while for species with smaller kOH than the vehicular indicator, the vehicular contribution would be underestimated by the method of characteristic ratios.

  12. Do vehicular emissions dominate the source of C6-C8 aromatics in the megacity Shanghai of eastern China?

    Institute of Scientific and Technical Information of China (English)

    Hongli Wang; Qian Wang; Jianmin Chen; Changhong Chen; Cheng Huang; Liping Qiao; Shengrong Lou

    2015-01-01

    The characteristic ratios of volatile organic compounds (VOCs) to i-pentane,the indicator of vehicular emissions,were employed to apportion the vehicular and non-vehicular contributions to reactive species in urban Shanghai.Two kinds of tunnel experiments,one tunnel with more than 90% light duty gasoline vehicles and the other with more than 60% light duty diesel vehicles,were carried out to study the characteristic ratios of vehicle-related emissions from December 2009 to January 2010.Based on the experiments,the characteristic ratios of C6-C8 aromatics to i-pentane of vehicular emissions were 0.53 ± 0.08 (benzene),0.70 ± 0.12 (toluene),0.41 ± 0.09 (m,p-xylenes),0.16 ± 0.04 (o-xylene),0.023 ± 0.011 (styrene),and 0.15 ± 0.02 (ethylbenzene),respectively.The source apportionment results showed that around 23.3% of C6-C8 aromatics in urban Shanghai were from vehicular emissions,which meant that the non-vehicular emissions had more importance.These findings suggested that emission control of non-vehicular sources,i.e.industrial emissions,should also receive attention in addition to the control of vehicle-related emissions in Shanghai.The chemical removal of VOCs during the transport from emissions to the receptor site had a large impact on the apportionment results.Generally,the overestimation of vehicular contributions would occur when the VOC reaction rate constant with OH radicals (kOH) was larger than that of the vehicular indicator,while for species with smaller kOH than the vehicular indicator,the vehicular contribution would be underestimated by the method of characteristic ratios.

  13. Airborne VOC measurements on board the Zeppelin NT during the PEGASOS campaigns in 2012 deploying the improvement Fast-GC-MSD system

    Energy Technology Data Exchange (ETDEWEB)

    Jaeger, Julia Elisabeth

    2014-04-01

    Volatile organic compounds (VOCs) comprise a large number of different species, estimated to 10{sup 4}-10{sup 6}. They are emitted on the Earth's surface from a variety of biogenic and anthropogenic sources. VOCs are removed by multiple pathways from the atmosphere, by oxidation and finally by dry or wet deposition. Most primary emitted VOCs are non-polar and therefore have a low solubility in water. Oxidation facilitates efficient VOC removal by wet deposition. In the atmosphere the main photochemical VOC oxidation agent is the OH radical. As a consequence the polarity of the VOCs is increased and they can be removed faster. The oxidation of VOCs proceeds in several steps until the VOCs are deposited or are eventually oxidized to carbon dioxide. A downside of the VOCs oxidation process lies in the production of significant amounts ozone if nitrogen oxide is present which is a serious health hazard. Most of the VOC oxidation takes place in lower part of the atmosphere between the altitudes of 100 to 1000 m, which is only sparsely analyzed. Therefore, fast VOCs measurements by GC-MSD on board the Zeppelin NT offered new important insights in the distribution of VOCs. The measurements were performed within the PEAGSOS campaigns in the Netherlands and in Italy in 2012. For the implementation of the GC-MSD system (HCG) on board the Zeppelin it was reconstructed to enhance its performance and to meet aviation requirements. The system was optimized to measure VOCs ranging from C4 to C10 as well as oxygenated VOCs (OVOCs) with a detection limit below 10 ppt. The analyzed VOCs for both parts of the campaigns showed low mean concentration below 5 ppb for all VOCs. Especially, the mixing ratios of the primary emitted VOCs were very low with mean values lower than 200 ppt. Higher concentrations could be observed for the OVOCs with mean concentrations up to 5 ppb. The most abundant OVOCs apart from formaldehyde were methanol, ethanol, acetone and acetaldehyde.

  14. Indoor air quality (IAQ) assessment in a multistorey shopping mall by high-spatial-resolution monitoring of volatile organic compounds (VOC).

    Science.gov (United States)

    Amodio, M; Dambruoso, P R; de Gennaro, Gianluigi; de Gennaro, L; Loiotile, A Demarinis; Marzocca, A; Stasi, F; Trizio, L; Tutino, M

    2014-12-01

    In order to assess indoor air quality (IAQ), two 1-week monitoring campaigns of volatile organic compounds (VOC) were performed in different areas of a multistorey shopping mall. High-spatial-resolution monitoring was conducted at 32 indoor sites located in two storehouses and in different departments of a supermarket. At the same time, VOC concentrations were monitored in the mall and parking lot area as well as outdoors. VOC were sampled at 48-h periods using diffusive samplers suitable for thermal desorption. The samples were then analyzed with gas chromatography-mass spectrometry (GC-MS). The data analysis and chromatic maps indicated that the two storehouses had the highest VOC concentrations consisting principally of terpenes. These higher TVOC concentrations could be a result of the low efficiency of the air exchange and intake systems, as well as the large quantity of articles stored in these small spaces. Instead, inside the supermarket, the food department was the most critical area for VOC concentrations. To identify potential emission sources in this department, a continuous VOC analyzer was used. The findings indicated that the highest total VOC concentrations were present during cleaning activities and that these activities were carried out frequently in the food department. The study highlights the importance of conducting both high-spatial-resolution monitoring and high-temporal-resolution monitoring. The former was able to identify critical issues in environments with a complex emission scenario while the latter was useful in interpreting the dynamics of each emission source.

  15. Ozone sensitivity to its precursor emissions in northeastern Mexico for a summer air pollution episode.

    Science.gov (United States)

    Sierra, A; Vanoye, A Y; Mendoza, A

    2013-10-01

    A summer episode was modeled to address the expected response of ambient air O3 to hypothetical emission control scenarios in northeastern Mexico, and in particular in the Monterrey Metropolitan Area (MMA). This region is of interest because the MMA holds one of the worst air quality problems in the country and levels of air pollutants in the rest of northeastern Mexico are starting to be a concern. The MM5-SMOKE-CMAQ platform was used to conduct the numerical experiments. Twenty-four control scenarios were evaluated, combining the level of emission controls of O3 precursors (NO(x) and volatile organic compounds [VOCs]) from 0% to 50%. For the MMA, VOC-only controls result in the best option to reduce O3 concentrations, though the benefit is limited to the urban core. This same strategy results in negligible benefits for the rest of northeastern Mexico. NO(x) controls result in an increase in O3 concentration within the MMA of up to 20 ppbv and a decrease at downwind locations of up to 11 ppbv, with respect to the base-case scenario. Indicator ratios were also used to probe for NO(x)-sensitive and VOC-sensitive areas. Locations with an important influence of NO(x) point sources (i.e., Monclova and Nava/Acuña) are quite sensitive to changes in NO(x) emissions. Border cities in the Rio Bravo/Grande Valley tend to be marginally NO(x)-sensitive. Overall, the MMA seems to be dominated by a VOC-sensitive regime, while the rest of the region would tend to have a NO(x)-sensitive response. The results obtained serve to expand the current knowledge on the chemical regimes that dominate this region (VOC- or NO(x)-sensitive), and thus could help guide public policies related to emission regional control strategies.

  16. VOC transport in vented drums containing simulated waste sludge

    Energy Technology Data Exchange (ETDEWEB)

    Liekhus, K.J.; Gresham, G.L.; Rae, C.; Connolly, M.J.

    1994-02-01

    A model is developed to estimate the volatile organic compound (VOC) concentration in the headspace of the innermost layer of confinement in a lab-scale vented waste drum containing simulated waste sludge. The VOC transport model estimates the concentration using the measured VOC concentration beneath the drum lid and model parameters defined or estimated from process knowledge of drum contents and waste drum configuration. Model parameters include the VOC diffusion characteristic across the filter vent, VOC diffusivity in air, size of opening in the drum liner lid, the type and number of layers of polymer bags surrounding the waste, VOC permeability across the polymer, and the permeable surface area of the polymer bags. Comparison of model and experimental results indicates that the model can accurately estimate VOC concentration in the headspace of the innermost layer of confinement. The model may be useful in estimating the VOC concentration in actual waste drums.

  17. Collaborative Research on the Ultra High Bypass Ratio Engine Cycle to Reduce Noise, Emissions and Fuel Consumption

    Science.gov (United States)

    Hughes, Christopher

    2008-01-01

    A pictorial history of NASA development of advanced engine technologies for reducing environmental emissions and increasing performance from the 1970s to present is presented. The goals of the Subsonic Fixed Wing Program portion of the NASA Fundamental Aeronautics Program are addressed, along with the areas of investigation currently being pursued by the Ultra High Bypass Partnership Element of the Subsonic Fixed Wing Program to meet the goals. Ultra High Bypass cycle research collaboration successes with Pratt & Whitney are presented.

  18. World Calibration Center for VOC (WCC-VOC), a new Facility for the WMO-GAW-Programme

    Science.gov (United States)

    Rappenglueck, B.-

    2002-12-01

    Volatile organic compounds (VOC) are recognized to be important precursors of tropospheric ozone as well as other oxidants and organic aerosols. In order to design effective control measures for the reduction of photooxidants, photochemical processes have to be understood and the sources of the precursors known. Reliable and representative measurements of VOCs are necessary to describe the anthropogenic and biogenic sources, to follow the photochemical degradation of VOCs in the troposphere. Measurement of VOCs is of key importance for the understanding of tropospheric chemistry. Tropospheric VOCs have been one of the recommended measurements to be made within the GAW programme. The purpose will be to monitor their atmospheric abundance, to characterize the various compounds with regard to anthropogenic and biogenic sources and to evaluate their role in the tropospheric ozone formation process. An international WMO/GAW panel of experts for VOC measurements developed the rational and objectives for this GAW activity and recommended the configuration and required activities of the WCC-VOC. In reflection of the complexity of VOC measurements and the current status of measurement technology, a "staged" approach was adopted. Stage 1 measurements: C2-C9 hydrocarbons, including alkanes, alkenes, alkynes, dienes and monocyclics. (The WCC-VOC operates currently under this mode). Stage 2 measurements: C10-C14 hydrocarbons, including higher homologs of the Stage 1 set as well as biogenic hydrocarbon compounds. Stage 3 measurements: Oxygenated VOCs, including alcohols, carbonyls, carboxylic acids. The Quality Assurance/Science Activity Centre (QA/SAC) Germany currently has established the World Calibration Centre for VOC (WCC-VOC). The WCC-VOC has operated in the research mode und has become operational recently. From now on, the WCC-VOC conducts one round-robin calibration audit per year at all global stations that measure VOCs and assists other stations in setting up VOC

  19. Comparison of the emissions and SFC for 10:1 and 12:1 compression ratio 1.8 litre SI engines using lean mixtures

    Energy Technology Data Exchange (ETDEWEB)

    Andrews, G.; Osses, M.; Desai, M.; Haralambidis, E. [Leeds Univ. (United Kingdom); Ounzain, A.; Robertson, G. [Ford Motor Co. Ltd., Dagenham (United Kingdom)

    1996-12-31

    A standard 10:1 compression ratio Ford Zetec engine was modified to a 12:1 compression ratio and investigated over the lean combustion region with a comparison with the base 10:1 compression ratio engine. All the comparisons were carried out at the same power output as for stoichiometric operation, using throttle adjustments to achieve the increased power as the mixture was made leaner. The aim of the higher compression ratio was to increase the power in the lean combustion region and thus to extend the lean burning limit for the same power output. The lean limit was then set as the wide open throttle lean combustion for a desired power output. The power outputs studied were 10 and 15KW at 1500 r/min, which is typical of the low power urban drive cycle in the EC emissions test cycle. Additional reductions in NOx using spark timing control was also investigated for lean mixtures. The lean burning capability at different conditions was investigated at the minimum fuel consumption spark timing and at 5% above the minimum SFC, but still below the SFC for stoichiometric operation. The borderline detonation limit (BLDL) as detected using a cylinder pressure transducer and spark timing loops were limited by the BLDL timing. The higher compression ratio was shown to extend the lean burning limit from 22/1 to 26/1 at constant 10KW power output. This was accompanied by an increase by NOx, hydrocarbons and CO. The extended lean limit was not effectively useable at 10 KW power due to the large increase in hydrocarbons for mixtures leaner than 22/1. Thus the lower NOx emissions in this region could not be exploited and there was little advantage, from a lean combustion viewpoint, of operation at 12/1 compression ratio. However, at the 15KW power output condition there were clear SFC advantages and smaller NOx reductions for the higher CR lean burn engine. (author)

  20. VOCs Speciation From Steam Boiler Stacks of Industries Located in Naucalpan

    Science.gov (United States)

    Mejia, G. M.; Tejeda, D. D.; Bremauntz, M. P.; Valdez, A.; Montufar, P. C.; Martinez, M. A.; Sierra, M. J.; Gonzalez, C. A.

    2007-05-01

    Results of VOCs speciation from industrial steam boiler stacks located in Naucalpan are presented and discussed. This municipality is located north of the Metropolitan Zone of the Valley of Mexico (MZVM). Speciation of VOCs is important to generate information about sources of pollution, to update emission inventories, to study the dynamics of pollutants in the atmosphere, and to estimate possible risks of population exposure. This information is valuable for decision making on air pollution control strategies. Samples from 35 steam boilers form industries burning Diesel, LPG, or CNG were taken using the US-EPA Method 18. Selected samples from the use of different fuels were analyzed using gas chromatography and flame ionization detection (GC-FID) according to US-EPA protocol TO-14. The VOCs analyzed included alkanes of 9 carbons or less, alkenes of 7 carbons or less and aromatics (families of benzene). The results show consistency on the VOCs detected on Diesel samples. The main compounds found were 1- Butene+iButylene, m/p-Xylene, Ethane, Propene, Propane, Acetylene, 2Me-1Butene, and Toluene. The average concentrations of these compounds were in the range of 130 to 385 ppbC. The results of LPG samples did not show a definite pattern of VOCs, although light components predominate and, in some samples, Toluene and Xylene. These last components were not expected for industries reporting the use of LPG, perhaps due to the use of a combination of fuels and mistakes in the reports of fuel used at the time of sampling. The analysis of CNG samples show predominance of light VOCs, in the range of 90 to 300 ppbC. As in the case of LPG, some aromatics showed high concentrations in some samples analyzed perhaps due to the use of different fuels in the boiler. The results of this study are the first results of VOCs speciation obtained form exhaust gases from stacks of Mexican industries. The data reported are valuable to analyze emission inventories of VOCs and to better

  1. GEIGER BRICKEL BENEFITS FROM LOW -VOC COATINGS

    Science.gov (United States)

    Midwest Research Institute, under a cooperative agreement with the U.S. Environmental Protection Agency (EPA), conducted a study to identify wood furniture manufacturing facilities that had converted to low-volatile organic compound (VOC)/hazardous air pollutant (HAP) wood furnit...

  2. The OIV 1407.3\\AA /1401.1\\AA\\ emission-line ratio in a plasma

    CERN Document Server

    Nessib, Nabil Ben; Qindeel, Rabia; Sahal-Bréchot, Sylvie; Dimitrijević, Milan S

    2013-01-01

    Line ratio of O IV 1407.3 \\AA/1401.1 \\AA\\- is calculated using mostly our own atomic and collisional data. Energy levels and oscillator strengths needed for this calculation have been calculated using a Hartree-Fock relativistic (HFR) approach. The electron collision strengths introduced in the statistic equilibrium equations are fitted by Line ratio of O IV 1407.3 \\AA/1401.1 \\AA\\- is calculated using mostly our own atomic and collisional data. Energy levels and oscillator strengths needed for this calculation have been calculated using a Hartree-Fock relativistic (HFR) approach. The electron collision strengths introduced in the statistic equilibrium equations are fitted by polynomials for different energies. Comparison has also been made with available theoretical results. The provided line ratio has been obtained for a set of electron densities from $10^{8}$ cm$^{-3}$ to $10^{13}$ cm$^{-3}$ and for a fixed temperature of 50 000 K.

  3. Contribution of low vapor pressure-volatile organic compounds (LVP-VOCs) from consumer products to ozone formation in urban atmospheres

    Science.gov (United States)

    Shin, Hyeong-Moo; McKone, Thomas E.; Bennett, Deborah H.

    2015-05-01

    Because recent laboratory testing indicates that some low vapor pressure-volatile organic compounds (LVP-VOC) solvents readily evaporate at ambient conditions, LVP-VOCs used in some consumer product formulations may contribute to ozone formation. The goal of this study is to determine the fraction of LVP-VOCs available for ozone formation from the use of consumer products for two hypothetical emissions. This study calculates and compares the fraction of consumed product available for ozone formation as a result of (a) volatilization to air during use and (b) down-the-drain disposal. The study also investigates the impact of different modes of releases on the overall fraction available in ambient air for ozone formation. For the portion of the LVP-VOCs volatilized to air during use, we applied a multi-compartment mass-balance model to track the fate of emitted LVP-VOCs in a multimedia urban environment. For the portion of the LVP-VOCs disposed down the drain, we used a wastewater treatment plant (WWTP) fate model to predict the emission rates of LVP-VOCs to ambient air at WWTPs or at the discharge zone of the facilities and then used these results as emissions in the multimedia urban environment model. In a WWTP, the LVP-VOCs selected in this study are primarily either biodegraded or removed via sorption to sludge depending on the magnitude of the biodegradation half-life and the octanol-water partition coefficient. Less than 0.2% of the LVP-VOCs disposed down the drain are available for ozone formation. In contrast, when the LVP-VOC in a consumer product is volatilized from the surface to which it has been applied, greater than 90% is available for photochemical reactions either at the source location or in the downwind areas. Comparing results from these two modes of releases allows us to understand the importance of determining the fraction of LVP-VOCs volatilized versus disposed down the drain when the product is used by consumers. The results from this study

  4. Trends of VOC exposures among a nationally representative sample: Analysis of the NHANES 1988 through 2004 data sets

    Science.gov (United States)

    Su, Feng-Chiao; Mukherjee, Bhramar; Batterman, Stuart

    2011-09-01

    Exposures to volatile organic compounds (VOCs) are ubiquitous due to emissions from personal, commercial and industrial products, but quantitative and representative information regarding long term exposure trends is lacking. This study characterizes trends from 1988 to 2004 for the 15 VOCs measured in blood in five cohorts of the National Health and Nutrition Examination Survey (NHANES), a large and representative sample of U.S. adults. Trends were evaluated at various percentiles using linear quantile regression (QR) models, which were adjusted for solvent-related occupations and cotinine levels. Most VOCs showed decreasing trends at all quantiles, e.g., median exposures declined by 2.5 (m,p-xylene) to 6.4 (tetrachloroethene) percent per year over the 15 year period. Trends varied by VOC and quantile, and were grouped into three patterns: similar decreases at all quantiles (including benzene, toluene); most rapid decreases at upper quantiles (ethylbenzene, m,p-xylene, o-xylene, styrene, chloroform, tetrachloroethene); and fastest declines at central quantiles (1,4-dichlorobenzene). These patterns reflect changes in exposure sources, e.g., upper-percentile exposures may result mostly from occupational exposure, while lower percentile exposures arise from general environmental sources. Both VOC emissions aggregated at the national level and VOC concentrations measured in ambient air also have declined substantially over the study period and are supportive of the exposure trends, although the NHANES data suggest the importance of indoor sources and personal activities on VOC exposures. While piecewise QR models suggest that exposures of several VOCs decreased little or any during the 1990's, followed by more rapid decreases from 1999 to 2004, questions are raised concerning the reliability of VOC data in several of the NHANES cohorts and its applicability as an exposure indicator, as demonstrated by the modest correlation between VOC levels in blood and personal air

  5. Spatial/temporal variations and source apportionment of VOCs monitored at community scale in an urban area.

    Directory of Open Access Journals (Sweden)

    Chang Ho Yu

    Full Text Available This study aimed to characterize spatial/temporal variations of ambient volatile organic compounds (VOCs using a community-scale monitoring approach and identify the main sources of concern in Paterson, NJ, an urban area with mixed sources of VOCs. VOC samples were simultaneously collected from three local source-dominated (i.e., commercial, industrial, and mobile sites in Paterson and one background site in Chester, NJ (located ∼58 km southwest of Paterson. Samples were collected using the EPA TO-15 method from midnight to midnight, one in every sixth day over one year. Among the 60 analyzed VOCs, ten VOCs (acetylene, benzene, dichloromethane, ethylbenzene, methyl ethyl ketone, styrene, toluene, m,p-xylene, o-xylene, and p-dichlorobenzene were selected to examine their spatial/temporal variations. All of the 10 VOCs in Paterson were significantly higher than the background site (p<0.01. Ethylbenzene, m,p-xylene, o-xylene, and p-dichlorobenzene measured at the commercial site were significantly higher than the industrial/mobile sites (p<0.01. Seven VOCs (acetylene, benzene, dichloromethane, methyl ethyl ketone, styrene, toluene, and p-dichlorobenzene were significantly different by season (p<0.05, that is, higher in cold seasons than in warm seasons. In addition, dichloromethane, methyl ethyl ketone, and toluene were significantly higher on weekdays than weekend days (p<0.05. These results are consistent with literature data, indicating the impact of anthropogenic VOC sources on air pollution in Paterson. Positive Matrix Factorization (PMF analysis was applied for 24-hour integrated VOC measurements in Paterson over one year and identified six contributing factors, including motor vehicle exhausts (20%, solvents uses (19%, industrial emissions (16%, mobile+stationery sources (12%, small shop emissions (11%, and others (22%. Additional locational analysis confirmed the identified sources were well matched with point sources located upwind in

  6. PM2.5 and volatile organic compounds (VOCs) in ambient air: a focus on the effect of meteorology.

    Science.gov (United States)

    Giakoumi, A; Maggos, Th; Michopoulos, J; Helmis, C; Vasilakos, Ch

    2009-05-01

    PM(2.5) and VOCs (benzene, toluene, m-p-o-xylenes) concentrations were measured in an urban and a suburban site in Athens, Greece, during the period between April and November 2004. This period, which is considered to be the warmer period in Greece, is characterized by the development of sea-breeze over the Attica Basin. Additionally strong Northern, North-eastern winds called "The Etesians", predominate during the summer months (July-August), acting positively to the dispersion of pollutants. In this campaign, 24 days with sea-breeze development were observed, 15 days with northern winds, 6 days with southern winds while the rest of the days presented no specific wind profile. Maximum concentrations of PM(2.5), VOCs and nitrogen oxides, were detected during the days with sea-breeze, while minimum concentrations during the days with northern winds. Ozone was the only pollutant that appeared to have higher concentrations in the background site and not in the city centre, where benzene presented strong negative correlation with ozone, indicating the photochemical reaction of hydrocarbons that lead to the ozone formation. The BTX ratios were similar for both sites and wind profiles, indicating common sources for those pollutants. T/B ratio ranged in low levels, between 3-5 for site A and 2-5 for site B, suggesting vehicles emissions as the main sources of volatile compounds. Finally, the strong correlations of PM(2.5) and benzene concentrations, between the two sampling sites, indicate that both the city centre and the background site, are affected by the same sources, under common meteorological conditions (sea-breeze, northern winds).

  7. Catalyst screening for the VOC decomposition using adsorption and oxygen plasma

    Energy Technology Data Exchange (ETDEWEB)

    Kim, H.H.; Ogata, A. [National Inst. of Advanced Industrial Science and Technology, Tokyo (Japan)

    2010-07-01

    Emissions of volatile organic compounds (VOCs) are directly related to the formation of photochemical smog and the secondary aerosol formation, particularly in urban areas. As such, VOC pollution control is a high priority in air quality management. Non-thermal plasmas (NTPs) have been considered for the abatement of VOCs, but 3 key factors must be addressed, notably improve the energy efficiency, have less NOx formation and acceptable material balance. A recent trend in the use of NTP for air pollution control is the combination of NTP with a catalyst. This combined process is subdivided into single-stage and two-stage depending on the position of the catalyst. Ozone-assisted catalysis is the two-stage system. This study focused on the decomposition of VOCs using a single-stage plasma-driven catalysis (PDC) system, and demonstrated the effectiveness of the PDC in terms of energy efficiency, product selectivity and carbon balance. The PDC reactor has a strong dependence on the oxygen content in the oxidation of VOCs. The potentials of various catalysts for cycled system were evaluated in terms of adsorption capability of VOC and enhancement factor (EF). The study focused on zeolites with a large surface area. Nanometer-sized active metals were also loaded on the zeolite surfaces, and their catalytic activity was tested. The metal nanoparticles supported on zeolites enhanced the catalytic activities considerably. ICCD camera observation of the discharge plasma on the surface of catalyst provided an important insight into the understanding of discharge plasma and catalyst. The area of discharge plasma expanded over a wide range by the metal nanoparticles. This physical influence was found to be closely related to the enhanced performance of the plasma-driven catalyst process. 15 refs., 5 figs.

  8. Rest-Frame Optical Emission Lines in z~3.5 Lyman Break selected Galaxies: The Ubiquity of Unusually High [OIII]/Hbeta Ratios at 2 Gyr

    CERN Document Server

    Holden, B P; Gonzalez, V G; Illingworth, G D; Labbe, I; Bouwens, R; Franx, M; van Dokkum, P; Spitler, L

    2014-01-01

    We present K-band spectra of rest-frame optical emission lines for 24 star-forming galaxies at z~3.2-3.7 using MOSFIRE on the Keck 1 telescope. Strong rest-frame optical [O III] and Hbeta emission lines were detected in 18 LBGs. The median flux ratio of [O III]5007 to Hbeta is 5.1+/-0.5, a factor of 5-10x higher than in local galaxies with similar stellar masses. The observed Hbeta luminosities are in good agreement with expectations from the estimated star-formation rates, and none of our sources are detected in deep X-ray stacks, ruling out significant contamination by active galactic nuclei. Combining our sample with a variety of LBGs from the literature, including 49 galaxies selected in a very similar manner, we find a high median ratio of [OIII]/Hbeta = 4.8+0.8-1.7. This high ratio seems to be an ubiquitous feature of z~3-4 LBGs, very different from typical local star-forming galaxies at similar stellar masses. The only comparable systems at z~0 are those with similarly high specific star-formation rate...

  9. NO and NO2 emission ratios measured from in-use commercial aircraft during taxi and takeoff.

    Science.gov (United States)

    Herndon, Scott C; Shorter, Joanne H; Zahniser, Mark S; Nelson, David D; Jayne, John; Brown, Robert C; Miake-Lye, Richard C; Waitz, Ian; Silva, Phillip; Lanni, Thomas; Demerjian, Ken; Kolb, Charles E

    2004-11-15

    In August 2001, the Aerodyne Mobile Laboratory simultaneously measured NO, NO2, and CO2 within 350 m of a taxiway and 550 m of a runway at John F. Kennedy Airport. The meteorological conditions were such that taxi and takeoff plumes from individual aircraft were clearly resolved against background levels. NO and NO2 concentrations were measured with 1 s time resolution using a dual tunable infrared laser differential absorption spectroscopy instrument, utilizing an astigmatic multipass Herriott cell. The CO2 measurements were also obtained at 1 s time resolution using a commercial non-dispersive infrared absorption instrument. Plumes were measured from over 30 individual planes, ranging from turbo props to jumbo jets. NOx emission indices were determined by examining the correlation between NOx (NO + NO2) and CO2 during the plume measurements. Several aircraft tail numbers were unambiguously identified, allowing those specific airframe/engine combinations to be determined. The resulting NOx emission indices from positively identified in-service operating airplanes are compared with the published International Civil Aviation Organization engine certification test database collected on new engines in certification test cells.

  10. The conversion probability and emission ratio of charged Sigma - hyperons following K/sup -/ meson capture at rest in carbon

    CERN Document Server

    Van der Velde-Wilquet, C; Sacton, J; Wickens, J H

    1975-01-01

    A study has been made of K/sup -/ meson interactions at rest in the CERN 1.1 m/sup 3/ heavy liquid bubble chamber filled with a mixture of hydrocarbons. The data are used to determine (i) the internal conversion probability, C( Sigma /sup -/), of Sigma /sup -/ hyperons produced in association with pi /sup +/ mesons by K/sup -/ meson interactions in carbon nuclei, (ii) the relative emission frequencies of ( Sigma /sup +/ pi /sup +/) and ( Sigma /sup -/ pi /sup +/) pairs, E( Sigma /sup +/ pi /sup +// Sigma /sup -/ pi /sup +/), and the emission frequency E( Sigma /sup +or-/ pi /sup -or+//K/sup -/), of ( Sigma /sup +or-/ pi /sup -or+/) pairs per K/sup -/ meson absorption in carbon, (iii) the branching fraction, P( Sigma /sup -/ pi /sup +//K /sup -/), for the primary process K/sup -/+p to Sigma /sup -/+ pi /sup +/ in carbon and (iv) the trapping probability, T( Lambda /sup 0/), for Lambda /sup 0/ hyperons produced by Sigma /sup -/ hyperon interactions in carbon nuclei. (26 refs).

  11. Estimation of emissions from field burning of crop straw in China

    Institute of Scientific and Technical Information of China (English)

    CAO GuoLiang; ZHANG XiaoYe; WANG YaQiang; Zheng FangCheng

    2008-01-01

    Emissions resulting from crop straw field burning in China, which have caused serious environmental problems in China, are estimated in this paper. From the county-level data of crop production in 2000-2003 from the government statistics, taking into account the ratio of residue and grain, the total amount of crop straw production is estimated to be about 600 Tg per year, 76% of which are rice, wheat and corn straw. With reference to the data of living standards, the percentage of crop straw burnt in fields for counties are obtained and consequently the total amount of burnt straws is approximately 140 Tg/year. With the emission factors from literature and experiments, appropriate emission factors have been obtained. The total amounts of PM, SO2, NOx, NH3, CH4, BC, OC, VOC, CO, CO2 emissions from field burning of crop straw in China are estimated. All emissions are presented at county level. Some pollutants, such as BC, VOC, OC, CO and CO2, are contributing a major portion to the total emissions of China. This paper uses a map with resolution of 0.2°×0.2° to present the PM emissions distribution from crop straw burnt in 2003. The results show a significant regional unevenness of emissions, with larger amounts of pollutions coming from the provinces in eastern and northeast China. The regions with higher emissions per unit area are located as a belt stretching from northeast China to eastern China.

  12. Seasonal variability and source apportionment of volatile organic compounds (VOCs) in the Paris megacity (France)

    Science.gov (United States)

    Baudic, Alexia; Gros, Valérie; Sauvage, Stéphane; Locoge, Nadine; Sanchez, Olivier; Sarda-Estève, Roland; Kalogridis, Cerise; Petit, Jean-Eudes; Bonnaire, Nicolas; Baisnée, Dominique; Favez, Olivier; Albinet, Alexandre; Sciare, Jean; Bonsang, Bernard

    2016-09-01

    Within the framework of air quality studies at the megacity scale, highly time-resolved volatile organic compound (C2-C8) measurements were performed in downtown Paris (urban background sites) from January to November 2010. This unique dataset included non-methane hydrocarbons (NMHCs) and aromatic/oxygenated species (OVOCs) measured by a GC-FID (gas chromatograph with a flame ionization detector) and a PTR-MS (proton transfer reaction - mass spectrometer), respectively. This study presents the seasonal variability of atmospheric VOCs being monitored in the French megacity and their various associated emission sources. Clear seasonal and diurnal patterns differed from one VOC to another as the result of their different origins and the influence of environmental parameters (solar radiation, temperature). Source apportionment (SA) was comprehensively conducted using a multivariate mathematical receptor modeling. The United States Environmental Protection Agency's positive matrix factorization tool (US EPA, PMF) was used to apportion and quantify ambient VOC concentrations into six different sources. The modeled source profiles were identified from near-field observations (measurements from three distinct emission sources: inside a highway tunnel, at a fireplace and from a domestic gas flue, hence with a specific focus on road traffic, wood-burning activities and natural gas emissions) and hydrocarbon profiles reported in the literature. The reconstructed VOC sources were cross validated using independent tracers such as inorganic gases (NO, NO2, CO), black carbon (BC) and meteorological data (temperature). The largest contributors to the predicted VOC concentrations were traffic-related activities (including motor vehicle exhaust, 15 % of the total mass on the annual average, and evaporative sources, 10 %), with the remaining emissions from natural gas and background (23 %), solvent use (20 %), wood-burning (18 %) and a biogenic source (15 %). An important finding of

  13. Comparison of emissions from on-road sources using a mobile laboratory under various driving and operational sampling modes

    Directory of Open Access Journals (Sweden)

    M. Zavala

    2009-01-01

    Full Text Available Mobile sources produce a significant fraction of the total anthropogenic emissions burden in large cities and have harmful effects on air quality at multiple spatial scales. Mobile emissions are intrinsically difficult to estimate due to the large number of parameters affecting the emissions variability within and across vehicles types. The MCMA-2003 Campaign in Mexico City has showed the utility of using a mobile laboratory to sample and characterize specific classes of motor vehicles to better quantify their emissions characteristics as a function of their driving cycles. The technique clearly identifies "high emitter" vehicles via individual exhaust plumes, and also provides fleet average emission rates. We have applied this technique to Mexicali during the Border Ozone Reduction and Air Quality Improvement Program (BORAQIP for the Mexicali-Imperial Valley in 2005. We analyze the variability of measured emission ratios for emitted NOx, CO, specific VOCs, NH3, and some primary fine particle components and properties by deploying a mobile laboratory in roadside stationary sampling, chase and fleet average operational sampling modes. The measurements reflect various driving modes characteristic of the urban fleets. The observed variability for all measured gases and particle emission ratios is greater for the chase and roadside stationary sampling than for fleet average measurements. The fleet average sampling mode captured the effects of traffic conditions on the measured on-road emission ratios, allowing the use of fuel-based emission ratios to assess the validity of traditional "bottom-up" emissions inventories. Using the measured on-road emission ratios, we estimate CO and NOx mobile emissions of 175±62 and 10.4±1.3 metric tons/day, respectively, for the gasoline vehicle fleet in Mexicali. Comparisons with similar on-road emissions data from Mexico City indicated that fleet average NO emission ratios were

  14. Chemical speciation and anthropogenic sources of ambient volatile organic compounds(VOCs)during summer in Beijing,2004

    Institute of Scientific and Technical Information of China (English)

    LU Sihua; LIU Ying; SHAO Min; HUANG Shan

    2007-01-01

    Volatile organic compounds(VOCs)were measured at six sites in Beijing in August,2004.Up to 148 VOC species,including C3 to C12 alkanes,C3 to C11 alkenes,C6 to C12 aromatics,and halogenated hydrocarbons,were quantified.Although the concentrations differed at the sites,the chemical compositions were similar,except for the Tongzhou site where aromatics were significantly high in the air.Based on the source profiles measured from previous studies,the source apportionment of ambient VOCs was preformed by deploying the chemical mass balance(CMB)model.The results show that urban VOCs are predominant from mobile source emissions,which contribute more than 50% of the VOCs(in mass concentrations)to ambient air at most sites.Other important sources are gasoline evaporation,painting,and solvents.The exception is at the Tongzhou site where vehicle exhaust,painting,and solvents have about equal contribution,around 35% of the ambient VOC concentration.As the receptor model is not valid for deriving the sources of reactive species,such as isoprene and 1,3-butadiene,other methodologies need to be further explored.

  15. Comparison of different real time VOC measurement techniques in a ponderosa pine forest

    Science.gov (United States)

    Kaser, L.; Karl, T.; Schnitzhofer, R.; Graus, M.; Herdlinger-Blatt, I. S.; DiGangi, J. P.; Sive, B.; Turnipseed, A.; Hornbrook, R. S.; Zheng, W.; Flocke, F. M.; Guenther, A.; Keutsch, F. N.; Apel, E.; Hansel, A.

    2013-03-01

    Volatile organic compound (VOC) mixing ratios measured by five independent instruments are compared at a forested site dominated by ponderosa pine (Pinus Ponderosa) during the BEACHON-ROCS field study in summer 2010. The instruments included a Proton Transfer Reaction Time of Flight Mass Spectrometer (PTR-TOF-MS), a Proton Transfer Reaction Quadrupole Mass Spectrometer (PTR-MS), a Fast Online Gas-Chromatograph coupled to a Mass Spectrometer (GC/MS; TOGA), a Thermal Dissociation Chemical Ionization Mass Spectrometer (PAN-CIMS) and a Fiber Laser-Induced Fluorescence Instrument (FILIF). The species discussed in this comparison include the most important biogenic VOCs and a selected suite of oxygenated VOCs that are thought to dominate the VOC reactivity at this particular site as well as typical anthropogenic VOCs that showed low mixing ratios at this site. Good agreement was observed for methanol, the sum of the oxygenated hemiterpene 2-methyl-3-buten-2-ol (MBO) and the hemiterpene isoprene, acetaldehyde, the sum of acetone and propanal, benzene and the sum of methyl ethyl ketone (MEK) and butanal. Measurements of the above VOCs conducted by different instruments agree within 20%. The ability to differentiate the presence of toluene and cymene by PTR-TOF-MS is tested based on a comparison with GC-MS measurements, suggesting a study-average relative contribution of 74% for toluene and 26% for cymene. Similarly, 2-hydroxy-2-methylpropanal (HMPR) is found to interfere with the sum of methyl vinyl ketone and methacrolein (MVK + MAC) using PTR-(TOF)-MS at this site. A study-average relative contribution of 85% for MVK + MAC and 15% for HMPR was determined. The sum of monoterpenes measured by PTR-MS and PTR-TOF-MS was generally 20-25% higher than the sum of speciated monoterpenes measured by TOGA, which included α-pinene, β-pinene, camphene, carene, myrcene, limonene, cineole as well as other terpenes. However, this difference is consistent throughout the study, and

  16. Comparison of different real time VOC measurement techniques in a ponderosa pine forest

    Directory of Open Access Journals (Sweden)

    L. Kaser

    2012-10-01

    Full Text Available Volatile organic compound (VOC mixing ratios measured by five independent instruments are compared at a forested site dominated by ponderosa pine (Pinus Ponderosa during the BEACHON-ROCS field study in summer 2010. The instruments included a Proton Transfer Reaction Time of Flight Mass Spectrometer (PTR-TOF-MS, a Proton Transfer Reaction Quadrupole Mass Spectrometer (PTR-MS, a Fast Online Gas-Chromatograph coupled to a Mass Spectrometer (GC/MS; TOGA, a Thermal Dissociation Chemical Ionization Mass Spectrometer (PAN-CIMS and a Fiber Laser-Induced Fluorescence Instrument (FILIF. The species discussed in this comparison include the most important biogenic VOCs and a selected suite of oxygenated VOCs that are thought to dominate the VOC reactivity at this particular site as well as typical anthropogenic VOCs that showed low mixing ratios at this site. Good agreement was observed for methanol, the sum of the oxygenated hemiterpene 2-methyl-3-buten-2-ol (MBO and the hemiterpene isoprene, acetaldehyde, the sum of acetone and propanal, benzene and the sum of methyl ethyl ketone (MEK and butanal. Measurements of the above VOCs conducted by different instruments agree within 20%. The ability to differentiate the presence of toluene and cymene by PTR-TOF-MS is tested based on a comparison with GC-MS measurements, suggesting a study-average relative contribution of 74% for toluene and 26% for cymene. Similarly, 2-hydroxy-2-methylpropanal (HMPR is found to interfere with the sum of methyl vinyl ketone and methacrolein (MVK+MAC using PTR-(TOF-MS at this site. A study-average relative contribution of 85% for MVK+MAC and 15% for HMPR was determined. The sum of monoterpenes measured by PTR-MS and PTR-TOF-MS was generally 20–25% higher than the sum of speciated monoterpenes measured by TOGA, which included α-pinene, β-pinene, camphene, carene, myrcene, limonene, cineole as well as other terpenes. However, this difference is consistent throughout the

  17. Comparison of different real time VOC measurement techniques in a ponderosa pine forest

    Directory of Open Access Journals (Sweden)

    L. Kaser

    2013-03-01

    Full Text Available Volatile organic compound (VOC mixing ratios measured by five independent instruments are compared at a forested site dominated by ponderosa pine (Pinus Ponderosa during the BEACHON-ROCS field study in summer 2010. The instruments included a Proton Transfer Reaction Time of Flight Mass Spectrometer (PTR-TOF-MS, a Proton Transfer Reaction Quadrupole Mass Spectrometer (PTR-MS, a Fast Online Gas-Chromatograph coupled to a Mass Spectrometer (GC/MS; TOGA, a Thermal Dissociation Chemical Ionization Mass Spectrometer (PAN-CIMS and a Fiber Laser-Induced Fluorescence Instrument (FILIF. The species discussed in this comparison include the most important biogenic VOCs and a selected suite of oxygenated VOCs that are thought to dominate the VOC reactivity at this particular site as well as typical anthropogenic VOCs that showed low mixing ratios at this site. Good agreement was observed for methanol, the sum of the oxygenated hemiterpene 2-methyl-3-buten-2-ol (MBO and the hemiterpene isoprene, acetaldehyde, the sum of acetone and propanal, benzene and the sum of methyl ethyl ketone (MEK and butanal. Measurements of the above VOCs conducted by different instruments agree within 20%. The ability to differentiate the presence of toluene and cymene by PTR-TOF-MS is tested based on a comparison with GC-MS measurements, suggesting a study-average relative contribution of 74% for toluene and 26% for cymene. Similarly, 2-hydroxy-2-methylpropanal (HMPR is found to interfere with the sum of methyl vinyl ketone and methacrolein (MVK + MAC using PTR-(TOF-MS at this site. A study-average relative contribution of 85% for MVK + MAC and 15% for HMPR was determined. The sum of monoterpenes measured by PTR-MS and PTR-TOF-MS was generally 20–25% higher than the sum of speciated monoterpenes measured by TOGA, which included α-pinene, β-pinene, camphene, carene, myrcene, limonene, cineole as well as other terpenes. However, this difference is consistent throughout the study

  18. A deeper look at the response of oxygenated and non oxygenated VOC to mid-term drought over the seasonal cycle: the case study of a drought-resistant species

    Science.gov (United States)

    Saunier, Amelie; Ormeño Lafuente, Elena; Wortham, Henri; Temime-Roussel, Brice; Fernandez, Catherine

    2015-04-01

    At the end of this century, climatic models plan an intensification of summer drought in the Mediterranean area due to a 30% rain reduction and a temperature rise of 3.4 °C. Plants respond to drought by modifying their primary (growth) and their secondary metabolism, the later being partly represented by volatile organic compound (VOC) emissions, such as terpenes. With drought, oxygenated and non oxygenated terpene emissions have been observed to increase, decrease or remain unchanged according to drought severity and vegetal model. By contrast, the response of non-terpenic oxygenated compounds to drought has been poorly studied. The aim of this study is to determine the potential impact of a two-year drought period on the full screen of VOC released by Q. pubescens, with a focus on both isoprene and methanol, issued from plant anabolism , and the numerous highly volatile oxygenated VOC, issued from plant catabolism (i.e. issued from oxidation of isoprene or methanol). A 70 years-old Downy oak forest (Quercus pubescens), highly resistant to drought stress, was selected as model ecosystem since it is well widespread in Southern France occupying 321 000 ha. Downy oak also represents the major source of isoprene emissions in the Mediterranean area and, unlike the other major Quercus sp. of the region (i.e. Quercus ilex, a monoterpene emitter) the impact of watering withholding over years has never been tackled. The study was performed at the experimental platform of O3HP (Oak Observatory at Observatoire de Haute Provence) in Southern France which is equipped with both a rain exclusion (by 30 %) and a rain addition structure (simulating the rainiest years of the region), allowing for comparison with naturally watered trees. Using dynamic enclosure chambers at the branch level and PTR-MS-Q-ToF, we screened the anabolic VOC (isoprene, methanol) and the catabolic VOC (e.g. methacrolein, methyl vinyl ketone, C6 aldehydes and carboxylic acids) of trees located under the

  19. The Helium Golden Ratios: triplet-singlet and G for He-like X-ray Emission

    Science.gov (United States)

    Stancil, Phillip C.; Miller, Ansley; Terry, Jason; Cumbee, Renata; Mullen, Patrick Dean; Schultz, David R.

    2017-06-01

    The existence of a mere two electrons manifests a multitude of interesting and diverse phenomena in the atomic structure of He-like ions including separate spin manifolds (singlets and triplets), unusual ordering of angular momentum states, and intercombination (i) and forbidden (f) radiative transitions. This rich behavior extends also to the dynamics involving He-like ions and various perturbers. While electrons have a propensity for exciting resonant (r) dipole-allowed transitions, heavy particles are far less selective. In this presentation, I'll illustrate how these properties play out in ion-neutral charge exchange (CX) processes which result in He-like product ions. The focus will be on the spin-multiplicity of the atomic ions and the quasi-molecular states involved in the interactions, how these affect the CX cross sections, and their impact on the resulting X-ray spectrum. In particular, the G-ratio, the ratio of Kα line intensities (f+i)/r, is very sensitive to the spin-dependent cross sections which in turn is dependent on the neutral target, whether open-shell like H (Nolte et al. 2012, 2017; Wu et al. 2012) or closed-shell like He or H2 (Cumbee et al. 2017; Mullen et al. 2016, 2017). Preliminary evidence also suggests that multielectron capture processes may influence the G-ratio when multielectron targets are involved.Cumbee R. S. et al. 2017, ApJ, submittedMullen, P. D. et al. 2016, ApJS, 224, 31Mullen, P. D. et al. 2017, ApJ, submittedNolte, J. et al. 2012, JPB, 45, 245202; 2017, to be submittedWu, Y. et al. 2012, JPB, 84, 022711This work was partially supported by NASA grants NNX09AC46G and NNG09WF24I.

  20. [Pollution characteristics and health risk assessment of atmospheric VOCs in the downtown area of Guangzhou, China].

    Science.gov (United States)

    Li, Lei; Li, Hong; Wang, Xue-Zhong; Zhang, Xin-Min; Wen, Chong

    2013-12-01

    The measurements of 31 kinds of VOCs in the ambient air of a site were carried out in the downtown of Guangzhou by online method from November 5, 2009 to November 9, 2009. The ambient level and composition characteristics, temporal variation characteristics, sources identification, and chemical reactivity of VOCs were studied, and the health risk of VOCs in the ambient air in the study area was assessed by using the international recognized health risk assessment method. Results showed that the mean and the range of the mass concentrations of 31 VOCs were 114.51 microg x m(-3) and 29.42-546.06 microg x m(-3), respectively. The mass concentrations of 31 VOCs, and those of alkanes, alkenes, and aromatics all showed a changing trend of higher in the morning and in the evening, and lower at noontime. Vehicular exhaust, gasoline and liquefied petroleum gas evaporates were the main sources of VOCs with the volatilization of paints and solvents being important emission sources. Toluene, trans-2-butene, m/p-xylene, i-butane, and 1,3,5-trimethylbenzene were the key reactive species among the 31 VOCs. Vehicular exhaust and gasoline evaporation were the main sources of VOCs leading to the formation of ozone. Health risk assessment showed that n-hexane, 1,3-butadiene, benzene, toluene, ethylbenzene, m/p-xylene and o-xylene had no appreciable risk of adverse non-cancer health effect on the exposed population, but 1, 3-butadiene and benzene had potential cancer risk. By comparing the corresponding data about health risk assessment of benzene compounds in some cities in China, it is concluded that benzene can impose relatively high cancer risk to the exposed populations in the ambient air of some cities in China. Therefore, strict countermeasures should be taken to further control the pollution of benzene in the ambient air of cities, and it is imperative to start the related studies and develop the atmospheric environmental health criteria and national ambient air quality

  1. Volatile emission from strawberry plants is induced by mite and leaf beetle feeding and methyl jasmonate

    OpenAIRE

    2006-01-01

    We have studied the emission of volatile organic compounds (VOCs) from young strawberry plants, cultivars Polka and Honeoye, after feeding by several strawberry herbivores under laboratory conditions. VOC profile of strawberry plants is highly dominated by green leaf volatiles (GLVs), which are released also due to mechanical damage. Our results reveal that strawberry has potential for inducible VOC defence, and this encourages testing the attractiveness of these strawberry VOCs to predatory ...

  2. Shocked POststarbust Galaxy Survey. I. Candidate Post-starbust Galaxies with Emission Line Ratios Consistent with Shocks

    Science.gov (United States)

    Alatalo, Katherine; Cales, Sabrina L.; Rich, Jeffrey A.; Appleton, Philip N.; Kewley, Lisa J.; Lacy, Mark; Lanz, Lauranne; Medling, Anne M.; Nyland, Kristina

    2016-06-01

    There are many mechanisms by which galaxies can transform from blue, star-forming spirals, to red, quiescent early-type galaxies, but our current census of them does not form a complete picture. Recent observations of nearby case studies have identified a population of galaxies that quench “quietly.” Traditional poststarburst searches seem to catch galaxies only after they have quenched and transformed, and thus miss any objects with additional ionization mechanisms exciting the remaining gas. The Shocked POststarburst Galaxy Survey (SPOGS) aims to identify transforming galaxies, in which the nebular lines are excited via shocks instead of through star formation processes. Utilizing the Oh-Sarzi-Schawinski-Yi (OSSY) measurements on the Sloan Digital Sky Survey Data Release 7 catalog, we applied Balmer absorption and shock boundary criteria to identify 1067 SPOG candidates (SPOGs*) within z = 0.2. SPOGs* represent 0.2% of the OSSY sample galaxies that exceed the continuum signal-to-noise cut (and 0.7% of the emission line galaxy sample). SPOGs* colors suggest that they are in an earlier phase of transition than OSSY galaxies that meet an “E+A” selection. SPOGs* have a 13% 1.4 GHz detection rate from the Faint Images of the Radio Sky at Twenty Centimeters Survey, higher than most other subsamples, and comparable only to low-ionization nuclear emission line region hosts, suggestive of the presence of active galactic nuclei (AGNs). SPOGs* also have stronger Na i D absorption than predicted from the stellar population, suggestive of cool gas being driven out in galactic winds. It appears that SPOGs* represent an earlier phase in galaxy transformation than traditionally selected poststarburst galaxies, and that a large proportion of SPOGs* also have properties consistent with disruption of their interstellar media, a key component to galaxy transformation. It is likely that many of the known pathways to transformation undergo a SPOG phase. Studying this sample of

  3. Experimental evaluation of the effect of compression ratio on performance and emission of SI engine fuelled with gasoline and n-butanol blend at different loads

    Directory of Open Access Journals (Sweden)

    Rinu Thomas

    2016-09-01

    Full Text Available Never ending demand for efficient and less polluting engines have always inspired newer technologies. Extensive study has been done on variable compression ratio, a promising in-cylinder technology, in the recent past. The present work is an experimental investigation to examine the variation of different parameters such as brake thermal efficiency, exhaust gas temperature and emissions with respect to change in compression ratio in a single-cylinder carbureted SI engine at different loads with two different fuels. Experiments were conducted at three different compression ratios (CR = 7:1, 8.5:1 and 10:1. The fuels used in this study are pure gasoline and 20% n-butanol blend (B20 in gasoline. The results showed that brake thermal efficiency increases with CR at all loads. Further, the experimental results showed the scope of improving the part-load efficiency of SI engine by adopting the concept of variable compression ratio (VCR technology, especially when fuels with better anti-knock characteristics are used. The uncertainty analysis of the experiments based on the specifications of the equipment used is also tabulated.

  4. Volatile organic emissions from the distillation and pyrolysis of vegetation

    Directory of Open Access Journals (Sweden)

    J. P. Greenberg

    2006-01-01

    Full Text Available Leaf and woody plant tissue (Pinus ponderosa, Eucalyptus saligna, Quercus gambelli, Saccharum officinarum and Oriza sativa were heated from 30 to 300°C and volatile organic compound (VOC emissions were identified and quantified. Major VOC emissions were mostly oxygenated and included acetic acid, furylaldehyde, acetol, pyrazine, terpenes, 2,3-butadione, phenol and methanol, as well as smaller emissions of furan, acetone, acetaldehyde, acetonitrile and benzaldehyde. Total VOC emissions from distillation and pyrolysis were on the order of 10 gC/kgC dry weight of vegetation, as much as 33% and 44% of CO2 emissions (gC(VOC/gC(CO2 measured during the same experiments, in air and nitrogen atmospheres, respectively. The emissions are similar in identity and quantity to those from smoldering combustion of woody tissue and of different character than those evolved during flaming combustion. VOC emissions from the distillation of pools and endothermic pyrolysis under low turbulence conditions may produce flammable concentrations near leaves and may facilitate the propagation of wildfires. VOC emissions from charcoal production are also related to distillation and pyrolysis; the emissions of the highly reactive VOCs from production are as large as the carbon monoxide emissions.

  5. Chemical characterization of emissions from a municipal solid waste treatment plant.

    Science.gov (United States)

    Moreno, A I; Arnáiz, N; Font, R; Carratalá, A

    2014-11-01

    Gaseous emissions are an important problem in municipal solid waste (MSW) treatment plants. The sources points of emissions considered in the present work are: fresh compost, mature compost, landfill leaks and leachate ponds. Hydrogen sulphide, ammonia and volatile organic compounds (VOCs) were analysed in the emissions from these sources. Hydrogen sulphide and ammonia were important contributors to the total emission volume. Landfill leaks are significant source points of emissions of H2S; the average concentration of H2S in biogas from the landfill leaks is around 1700 ppmv. The fresh composting site was also an important contributor of H2S to the total emission volume; its concentration varied between 3.2 and 1.7 ppmv and a decrease with time was observed. The mature composting site showed a reduction of H2S concentration (<0.1 ppmv). Leachate pond showed a low concentration of H2S (in order of ppbv). Regarding NH3, composting sites and landfill leaks are notable source points of emissions (composting sites varied around 30-600 ppmv; biogas from landfill leaks varied from 160 to 640 ppmv). Regarding VOCs, the main compounds were: limonene, p-cymene, pinene, cyclohexane, reaching concentrations around 0.2-4.3 ppmv. H2S/NH3, limonene/p-cymene, limonene/cyclohexane ratios can be useful for analysing and identifying the emission sources.

  6. Comparison of emissions inventories of anthropogenic air pollutants and greenhouse gases in China

    Science.gov (United States)

    Saikawa, Eri; Kim, Hankyul; Zhong, Min; Avramov, Alexander; Zhao, Yu; Janssens-Maenhout, Greet; Kurokawa, Jun-ichi; Klimont, Zbigniew; Wagner, Fabian; Naik, Vaishali; Horowitz, Larry W.; Zhang, Qiang

    2017-05-01

    Anthropogenic air pollutant emissions have been increasing rapidly in China, leading to worsening air quality. Modelers use emissions inventories to represent the temporal and spatial distribution of these emissions needed to estimate their impacts on regional and global air quality. However, large uncertainties exist in emissions estimates. Thus, assessing differences in these inventories is essential for the better understanding of air pollution over China. We compare five different emissions inventories estimating emissions of carbon dioxide (CO2), carbon monoxide (CO), nitrogen oxides (NOx), sulfur dioxide (SO2), and particulate matter with an aerodynamic diameter of 10 µm or less (PM10) from China. The emissions inventories analyzed in this paper include the Regional Emission inventory in ASia v2.1 (REAS), the Multi-resolution Emission Inventory for China (MEIC), the Emission Database for Global Atmospheric Research v4.2 (EDGAR), the inventory by Yu Zhao (ZHAO), and the Greenhouse Gas and Air Pollution Interactions and Synergies (GAINS). We focus on the period between 2000 and 2008, during which Chinese economic activities more than doubled. In addition to national totals, we also analyzed emissions from four source sectors (industry, transport, power, and residential) and within seven regions in China (East, North, Northeast, Central, Southwest, Northwest, and South) and found that large disagreements exist among the five inventories at disaggregated levels. These disagreements lead to differences of 67 µg m-3, 15 ppbv, and 470 ppbv for monthly mean PM10, O3, and CO, respectively, in modeled regional concentrations in China. We also find that all the inventory emissions estimates create a volatile organic compound (VOC)-limited environment and MEIC emissions lead to much lower O3 mixing ratio in East and Central China compared to the simulations using REAS and EDGAR estimates, due to their low VOC emissions. Our results illustrate that a better

  7. Ethanol emission from loose corn silage and exposed silage particles

    Science.gov (United States)

    Hafner, Sasha D.; Montes, Felipe; Rotz, C. Alan; Mitloehner, Frank

    2010-11-01

    Silage on dairy farms has been identified as a major source of volatile organic compound (VOC) emissions. However, rates of VOC emission from silage are not accurately known. In this work, we measured ethanol (a dominant silage VOC) emission from loose corn silage and exposed corn silage particles using wind tunnel systems. Flux of ethanol was highest immediately after exposing loose silage samples to moving air (as high as 220 g m -2 h -1) and declined by as much as 76-fold over 12 h as ethanol was depleted from samples. Emission rate and cumulative 12 h emission increased with temperature, silage permeability, exposed surface area, and air velocity over silage samples. These responses suggest that VOC emission from silage on farms is sensitive to climate and management practices. Ethanol emission rates from loose silage were generally higher than previous estimates of total VOC emission rates from silage and mixed feed. For 15 cm deep loose samples, mean cumulative emission was as high as 170 g m -2 (80% of initial ethanol mass) after 12 h of exposure to an air velocity of 5 m s -1. Emission rates measured with an emission isolation flux chamber were lower than rates measured in a wind tunnel and in an open setting. Results show that the US EPA emission isolation flux chamber method is not appropriate for estimating VOC emission rates from silage in the field.

  8. Effect of [Li]/[Nb] ratios on the absorption and up-conversion emission spectra in In:Yb:Ho:LiNbO{sub 3} crystal

    Energy Technology Data Exchange (ETDEWEB)

    Dai, Li, E-mail: daili198108@126.com [Applied Science College, Harbin University of Science and Technology, Harbin 150080 (China); State Key Laboratory of Crystal Material, Shandong University, Jinan 250100 (China); Yan, Zhehua; Jiao, Shanshan [Applied Science College, Harbin University of Science and Technology, Harbin 150080 (China); Xu, Chao; Xu, Yuheng [Department of the Applied Chemistry, Harbin Institute of Technology, Harbin 150001 (China)

    2015-09-25

    Highlights: • In:Yb:Ho:LiNbO{sub 3} crystals were grown with various [Li]/[Nb] ratios. • The influence of [Li]/[Nb] ratios on the UV–VIS–NIR is investigated. • This UC process is three-photon process. • In:Yb:Ho:LiNbO{sub 3} crystals (Li/Nb = 1.38) is a promising material for 2 μm wavelength radiation. - Abstract: In:Yb:Ho:LiNbO{sub 3} crystals with high optical quality were grown by the Czochralski method with various ratios of [Li]/[Nb], that is 0.94, 1.05, 1.20 and 1.38 in the melt. The UV–VIS–NIR absorption spectra of In:Yb:Ho:LiNbO{sub 3} crystals were measured. The transition intensity parameters Ω{sub t} (t = 2, 4 and 6), spectroscopic quality factor (X) and the lifetimes of Ho{sup 3+} in In:Yb:Ho:LiNbO{sub 3} crystals were all evaluated by the Judd–Ofelt theory. The spectroscopic quality factor Ω{sub 4}/Ω{sub 6} of In:Yb:Ho:LiNbO{sub 3} crystals with the [Li]/[Nb] ratio of 1.38 was found to be 1.69, which is comparable with those found in widely used Ho{sup 3+} doped crystals. Furthermore, up-conversion emission spectra were determined and analyzed under 980 nm LD excitation in the In:Yb:Ho:LiNbO{sub 3} crystals. The results revealed that In:Yb:Ho:LiNbO{sub 3} crystal with the [Li]/[Nb] ratio of 1.38 is a promising material for 2 μm wavelength radiation.

  9. Characterization of on-road vehicle emissions in the Mexico City Metropolitan Area using a mobile laboratory in chase and fleet average measurement modes during the MCMA-2003 field campaign

    Directory of Open Access Journals (Sweden)

    M. Zavala

    2006-06-01

    Full Text Available A mobile laboratory was used to measure on-road vehicle emission ratios during the MCMA-2003 field campaign held during the spring of 2003 in the Mexico City Metropolitan Area (MCMA. The measured emission ratios represent a sample of emissions of in-use vehicles under real world driving conditions for the MCMA. From the relative amounts of NOx and selected VOC's sampled, the results indicate that the technique is capable of differentiating among vehicle categories and fuel type in real world driving conditions. Emission ratios for NOx, NOy, NH3, H2CO, CH3CHO, and other selected volatile organic compounds (VOCs are presented for chase sampled vehicles and fleet averaged emissions. Results indicate that colectivos, particularly CNG-powered colectivos, are potentially significant contributors of NOx and aldehydes in the MCMA. Similarly, ratios of selected VOCs and NOy showed a strong dependence on traffic mode. These results are compared with the vehicle emissions inventory for the MCMA, other vehicle emissions measurements in the MCMA, and measurements of on-road emissions in US cities. Our estimates for motor vehicle emissions of benzene, toluene, formaldehyde, and acetaldehyde in the MCMA indicate these species are present in concentrations higher than previously reported. The high motor vehicle aldehyde emissions may have an impact on the photochemistry of urban areas.

  10. Ultraviolet and radical oxidation of airborne VOC`s. Technical report

    Energy Technology Data Exchange (ETDEWEB)

    Heinsohn, R.J.; Spaeder, T.A.; Albano, M.T.; Schmelzle, J.P.; Fetter, R.O.

    1994-03-18

    Airborne VOC`s reactions initiated by UV radiation at selected wavelengths from 185 to 308 nm have been studied. A simplified chemical kinetic mechanism is proposed incorporating photolysis and radical reactions. The concentration of HCHO and CH{sub 3}OH were predicted as a function of time, radiation wavelength, actinic flux and initial ozone concentration. The gas velocity and HCHO concentration were predicted in a gas stream flowing over a UV bulb. Experiments were conducted in which ethanol vapor and air were irradiated by low-pressure mercury bulbs. Ethanol disappeared in an overall first-order manner and an intermediate species, believed to be acetaldehyde, appeared and then disappeared.

  11. X-ray to NIR emission from AA Tauri during the dim state - Occultation of the inner disk and gas-to-dust ratio of the absorber

    CERN Document Server

    Schneider, P C; Günther, H M; Herczeg, G J; Robrade, J; Bouvier, J; McJunkin, M; Schmitt, J H M M

    2015-01-01

    AA Tau is a well-studied, nearby classical T Tauri star, which is viewed almost edge-on. A warp in its inner disk periodically eclipses the central star, causing a clear modulation of its optical light curve. The system underwent a major dimming event beginning in 2011 caused by an extra absorber, which is most likely associated with additional disk material in the line of sight toward the central source. We present new XMM-Newton X-ray, Hubble Space Telescope FUV, and ground based optical and near-infrared data of the system obtained in 2013 during the long-lasting dim phase. The line width decrease of the fluorescent H$_2$ disk emission shows that the extra absorber is located at $r>1\\,$au. Comparison of X-ray absorption ($N_H$) with dust extinction ($A_V$), as derived from measurements obtained one inner disk orbit (eight days) after the X-ray measurement, indicates that the gas-to-dust ratio as probed by the $N_H$ to $A_V$ ratio of the extra absorber is compatible with the ISM ratio. Combining both result...

  12. Large eddy simulation of reactive pollutants in a deep urban street canyon: Coupling dynamics with O3-NOx-VOC chemistry.

    Science.gov (United States)

    Zhong, Jian; Cai, Xiao-Ming; Bloss, William James

    2017-02-12

    A large eddy simulation (LES) model coupled with O3-NOx-VOC chemistry is implemented to simulate the coupled effects of emissions, mixing and chemical pre-processing within an idealised deep (aspect ratio = 2) urban street canyon under a weak wind condition. Reactive pollutants exhibit significant spatial variations in the presence of two vertically aligned unsteady vortices formed in the canyon. Comparison of the LES results from two chemical schemes (simple NOx-O3 chemistry and a more comprehensive Reduced Chemical Scheme (RCS) chemical mechanism) shows that the concentrations of NO2 and Ox inside the street canyon are enhanced by approximately 30-40% via OH/HO2 chemistry. NO, NOx, O3, OH and HO2 are chemically consumed, while NO2 and Ox (total oxidant) are chemically produced within the canyon environment. Within-canyon pre-processing increases oxidant fluxes from the canyon to the overlying boundary layer, and this effect is greater for deeper street canyons (as found in many traditional European urban centres) than shallower (lower aspect ratio) streets. There is clear evidence of distinct behaviours for emitted chemical species and entrained chemical species, and positive (or negative) values of intensities of segregations are found between pairs of species with similar (or opposite) behaviour. The simplified two-box model underestimated NO and O3 levels, but overestimated NO2 levels for both the lower and upper canyon compared with the more realistic LES-chemistry model. This suggests that the segregation effect due to incomplete mixing reduces the chemical conversion rate of NO to NO2. This study reveals the impacts of nonlinear O3-NOx-VOC photochemical processes in the incomplete mixing environment and provides a better understanding of the pre-processing of emissions within canyons, prior to their release to the urban boundary layer, through the coupling of street canyon dynamics and chemistry.

  13. Research on the Emission Inventory of Major Air Pollutants in 2012 for the Sichuan City Cluster in China

    Science.gov (United States)

    Qian, J.; He, Q.

    2014-12-01

    This paper developed a high resolution emission inventory of major pollutants in city cluster of Sichuan Basin, one of the most polluted regions in China. The city cluster included five cities, which were Chengdu, Deyang, Mianyang, Meishan and Ziyang. Pollution source census and field measurements were conducted for the major emission sources such as the industry sources, on-road mobile sources, catering sources and the dust sources. The inventory results showed that in the year of 2012, the emission of SO2、NOX、CO、PM10、PM2.5、VOCs and NH3 in the region were 143.5、251.9、1659.9、299.3、163.5、464.1 and 995kt respectively. Chengdu, the provincial capital city, had the largest emission load of every pollutant among the cities. The industry sources, including power plants, fuel combustion facilities and non-combustion processes were the largest emission sources for SO2、NOX and CO, contributing to 84%, 46.5%, 35% of total SO2, NOX and CO emissions. On-road mobile sources accounted for 46.5%, 33%, 16% of the total NOx, CO, PM2.5 emissions and 28% of the anthropogenic VOCs emission. Dust and industry sources contributed to 42% and 23% of the PM10 emission with the dust sources also as the largest source of PM2.5, contributing to 27%. Anthropogenic and biogenic sources took 75% and 25% of the total VOCs emission while 36% of anthropogenic VOCs emission was owing to solvent use. Livestock contributed to 62% of NH3 emissions, followed by nitrogen fertilizer application whose contribution was 23%. Based on the developed emission inventory and local meteorological data, the regional air quality modeling system WRF-CMAQ was applied to simulate the status of PM2.5 pollution in a regional scale. The results showed that high PM2.5 concentration was distributed over the urban area of Chengdu and Deyang. On-road mobile sources and dust sources were two major contributors to the PM2.5 pollution in Chengdu, both had an contribution ratio of 27%. In Deyang, Mianyang

  14. Pulsed Corona Discharges and Their Applications in Toxic VOCs Abatement

    Institute of Scientific and Technical Information of China (English)

    MuhammadArifMalik; SalmanAkbarMalik

    1999-01-01

    plasma processes are among the emerging technologies for volatile organic compounds (VOCs) sbatoment. Both thermal plasmas and non-equil[brimn plasmas (cold plasmas) are being developed for VOCs clesnup. Particularly, pulsed corona discharges offer several edvantages over conventional VOCs abatement tochniqvee, To optimize the existing technology and to developit further, there is need to understand the mechanlsms involved in plasma chemical reacticms, Furthermore, it is strongly desirable to be able to predict the behavior of new VOCs in non-equillbrlum plasma enviromuent from the data known for a few representative oompounds, Pulsed corona discharge technique is introduced here with dtafion of refevant literature, Fundamental principfes,useful for predicting the VOCs' decomposition behavior, have been worked out from the published literature. Latest developments in the area, targeted to minimize the enersy losses, improve the VOCs destruction efficiency and reduce the generation of unwanted organic and inorganic by-products, are presented.

  15. Source apportionment of VOCs and the contribution to photochemical ozone formation during summer in the typical industrial area in the Yangtze River Delta, China

    Science.gov (United States)

    Shao, Ping; An, Junlin; Xin, Jinyuan; Wu, Fangkun; Wang, Junxiu; Ji, Dongsheng; Wang, Yuesi

    2016-07-01

    Volatile organic compounds (VOCs) were continuously observated in a northern suburb of Nanjing, a typical industrial area in the Yangtze River Delta, in a summer observation period from 15th May to 31st August 2013. The average concentration of total VOCs was (34.40 ± 25.20) ppbv, including alkanes (14.98 ± 12.72) ppbv, alkenes (7.35 ± 5.93) ppbv, aromatics (9.06 ± 6.64) ppbv and alkynes (3.02 ± 2.01) ppbv, respectively. Source apportionment via Positive Matrix Factorization was conducted, and six major sources of VOCs were identified. The industry-related sources, including industrial emissions and industrial solvent usage, occupied the highest proportion, accounting for about 51.26% of the VOCs. Vehicular emissions occupied the second highest proportion, accounting for about 34.08%. The rest accounted for about 14.66%, including vegetation emission and liquefied petroleum gas/natural gas usage. Contributions of VOCs to photochemical O3 formation were evaluated by the application of a detailed chemical mechanism model (NCAR MM). Alkenes were the dominant contributors to the O3 photochemical production, followed by aromatics and alkanes. Alkynes had a very small impact on photochemical O3 formation. Based on the outcomes of the source apportionment, a sensitivity analysis of relative O3 reduction efficiency (RORE), under different source removal regimes such as using the reduction of VOCs from 10% to 100% as input, was conducted. The RORE was the highest (~ 20%-40%) when the VOCs from solvent-related sources decreased by 40%. The highest RORE values for vegetation emissions, industrial emissions, vehicle exhaust, and LPG/NG usage were presented in the scenarios of 50%, 80%, 40% and 40%, respectively.

  16. [Comparison Analysis of Economic and Engineering Control of Industrial VOCs].

    Science.gov (United States)

    Wang, Yu-fei; Liu, Chang-xin; Cheng, Jie; Hao, Zheng-ping; Wang, Zheng

    2015-04-01

    Volatile organic compounds (VOCs) pollutant has become China's major air pollutant in key urban areas like sulfur dioxide, nitrogen oxides and particulate matter. It is mainly produced from industry sectors, and engineering control is one of the most important reduction measures. During the 12th Five-Year Plan, China decides to invest 40 billion RMB to build pollution control projects in key industry sectors with annual emission reduction of 605 000 t x a(-1). It shows that China attaches a great importance to emission reduction by engineering projects and highlights the awareness of engineering reduction technologies. In this paper, a macroeconomic model, namely computable general equilibrium model, (CGE model) was employed to simulate engineering control and economic control (imposing environmental tax). We aim to compare the pros and cons of the two reduction policies. Considering the economic loss of the whole country, the environmental tax has more impacts on the economy system than engineering reduction measures. We suggest that the central government provides 7 500 RMB x t(-1) as subsidy for enterprises in industry sectors to encourage engineering reduction.

  17. Are Some Fungal Volatile Organic Compounds (VOCs) Mycotoxins?

    OpenAIRE

    Bennett, Joan W.; Arati A. Inamdar

    2015-01-01

    Volatile organic compounds (VOCs) are carbon-compounds that easily evaporate at room temperature. Toxins are biologically produced poisons; mycotoxins are those toxins produced by microscopic fungi. All fungi emit blends of VOCs; the qualitative and quantitative composition of these volatile blends varies with the species of fungus and the environmental situation in which the fungus is grown. These fungal VOCs, produced as mixtures of alcohols, aldehydes, acids, ethers, esters, ketones, terpe...

  18. Outdoor, indoor, and personal exposure to VOCs in children.

    Science.gov (United States)

    Adgate, John L; Church, Timothy R; Ryan, Andrew D; Ramachandran, Gurumurthy; Fredrickson, Ann L; Stock, Thomas H; Morandi, Maria T; Sexton, Ken

    2004-10-01

    We measured volatile organic compound (VOC) exposures in multiple locations for a diverse population of children who attended two inner-city schools in Minneapolis, Minnesota. Fifteen common VOCs were measured at four locations: outdoors (O), indoors at school (S), indoors at home (H), and in personal samples (P). Concentrations of most VOCs followed the general pattern O approximately equal to S long-term health risks from children's exposure to these compounds.

  19. Remove volatile organic compounds (VOCs) with membrane separation techniques

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    Membrane separation, a new technology for removing VOCs including pervaporation, vapor permeation, membrane contactor, and membrane bioreactor was presented. Comparing with traditional techniques, these special techniques are an efficient and energy-saving technology. Vapor permeation can be applied to recovery of organic solvents from exhaust streams. Membrane contactor could be used for removing or recovering VOCs from air or wastewater. Pervaporation and vapor permeation are viable methods for removing VOCs from wastewater to yield a VOC concentrate which could either be destroyed by conventional means, or be recycled for reuse.

  20. Use of mass spectrometric methods for field screening of VOC`s

    Energy Technology Data Exchange (ETDEWEB)

    Evans, J.C.

    1994-11-01

    While mass spectrometric (MS) methods of chemical analysis, particularly gas chromatography-mass spectrometry (GC/MS), have been the mainstay of environmental organic analytical techniques in the laboratory through the use of EPA and other standard methods, field implementation is relatively rare. Instrumentation and methods now exist for utilizing MS and GC/MS techniques in the field for analysis of VOC`s in gas phase, aqueous, and soil media. Examples of field investigations utilizing HP 5971A and Viking SpectraTrak systems for analysis of VOC`s in all three media will be presented. Mass spectral methods were found to offer significant advantages in terms of speed of analysis and reliability of compound identification over field gas chromatography (GC) methods while preserving adequate levels of detection sensitivity. The soil method in particular provides a method for rapid in-field analysis of methanol preserved samples thus minimizing the problem of volatiles loss which typically occurs with routine use of the EPA methods and remote analysis. The high cost of MS instrumentation remains a major obstacle to more widespread use.

  1. New insights in the interpretation of tryptophan fluorescence : origin of the fluorescence lifetime and characterization of a new fluorescence parameter in proteins: the emission to excitation ratio.

    Science.gov (United States)

    Albani, J R

    2007-07-01

    Origin of tryptophan fluorescence is still up to these days a quiz which is not completely solved. Fluorescence emission properties of tryptophan within proteins are in general considered as the result of fluorophore interaction within its environment. For example, a low fluorescence quantum yield is supposed to be the consequence of an important fluorophore-environment interaction. However, are we sure that the fluorophore has been excited upon light absorption? What if fluorophore excitation did not occur as the result of internal conformation specific to the fluorophore environment? Are we sure that all absorbed energy is used for the excitation process? Fluorescence lifetimes of Trp residues are considered to originate from rotamers or conformers resulting from the rotation of the indole ring within the peptide bonds. However, how can we explain the fact that in most of the proteins, the two lifetimes 0.5 and 3 ns, attributed to the conformers, are also observed for free tryptophan in solution? The present work, performed on free tryptophan and tyrosine in solution and on different proteins, shows that absorption and excitation spectra overlap but their intensities at the different excitation wavelengths are not necessarily equal. Also, we found that fluorescence emission intensities recorded at different excitation wavelengths depend on the intensities at these excitation wavelengths and not on the optical densities. Thus, excitation is not equal to absorption. In our interpretation of the data, we consider that absorbed photons are not necessary used only for the excitation, part of them are used to reorganize fluorophore molecules in a new state (excited structure) and another part is used for the excitation process. A new parameter that characterizes the ratio of the number of emitted photons over the real number of photons used to excite the fluorophore can be defined. We call this parameter, the emission to excitation ratio. Since our results were

  2. Numerical modeling analysis of VOC removal processes in different aerobic vertical flow systems for groundwater remediation.

    Science.gov (United States)

    De Biase, Cecilia; Carminati, Andrea; Oswald, Sascha E; Thullner, Martin

    2013-11-01

    Vertical flow systems filled with porous medium have been shown to efficiently remove volatile organic contaminants (VOCs) from contaminated groundwater. To apply this semi-natural remediation strategy it is however necessary to distinguish between removal due to biodegradation and due to volatile losses to the atmosphere. Especially for (potentially) toxic VOCs, the latter needs to be minimized to limit atmospheric emissions. In this study, numerical simulation was used to investigate quantitatively the removal of volatile organic compounds in two pilot-scale water treatment systems: an unplanted vertical flow filter and a planted one, which could also be called a vertical flow constructed wetland, both used for the treatment of contaminated groundwater. These systems were intermittently loaded with contaminated water containing benzene and MTBE as main VOCs. The highly dynamic but permanently unsaturated conditions in the porous medium facilitated aerobic biodegradation but could lead to volatile emissions of the contaminants. Experimental data from porous material analyses, flow rate measurements, solute tracer and gas tracer test, as well as contaminant concentration measurements at the boundaries of the systems were used to constrain a numerical reactive transport modeling approach. Numerical simulations considered unsaturated water flow, transport of species in the aqueous and the gas phase as well as aerobic degradation processes, which made it possible to quantify the rates of biodegradation and volatile emissions and calculating their contribution to total contaminant removal. A range of degradation rates was determined using experimental results of both systems under two operation modes and validated by field data obtained at different operation modes applied to the filters. For both filters, simulations and experimental data point to high biodegradation rates, if the flow filters have had time to build up their removal capacity. For this case volatile

  3. Emissions of volatile organic compounds from heated needles and twigs of Pinus pumila

    Institute of Scientific and Technical Information of China (English)

    ZHAO Feng-jun; SHU Li-fu; WANG Qiu-hua; WANG Ming-yu; TIAN Xiao-rui

    2011-01-01

    A study was conducted to explore the mechanism that emissions of volatile organic compounds (VOC) from heated needles and twigs (200℃, within 15 min) of Pinus purnila affect fire behaviours using the technology of Thermal Desorption - Gas Chromatography-Mass Spectrometry (TD-GC-MS). The results indicated that the main components of VOC from heated needles and twigs are terpenoids. Most of these terpenoids are monoterpenes. Terpenoids account for 72.93% for the needles and 92.40% for the twigs of the total VOC, and their emis sion ratios are 61.200 μg·g-1 and 217.060 μtg·g-1 respectively. Heated twigs can emit more terpenoids than heated needles because twigs had more volatile oils than needles. In actual fires, these large amounts of terpenoid emissions, especially the monoterpene emissions, have strong effects on fire behaviors that are not only in the initial stage but also in the fast propagation stage of fires. These flammable gases are capable of causing violent combustion and creating crown fires. In addition, if these gases accumulate in an uneven geographical area, there will be a possible for eruptive fires and/or fires fiashover to occur.

  4. Assessment of odorous VOCs released from a main MSW landfill site in Istanbul-Turkey via a modelling approach.

    Science.gov (United States)

    Saral, Arslan; Demir, Selami; Yildiz, Senol

    2009-08-30

    An air pollution modeling study was conducted to investigate the odorous effects of volatile organic compounds (VOCs) emissions from a sanitary landfill area on ambient air quality. The atmospheric dispersion of hydrogen sulfide (H(2)S) and 22 VOCs was modeled. Industrial Source Complex v3 Short Term (ISCST3) model was used to estimate hourly concentrations of odorous VOCs over the nearest residential area. Odor thresholds of VOCs of interest were also found in the literature. Results showed that short-term averages of three odorous VOCs, namely ethyl mercaptan, methyl mercaptan and hydrogen sulfide, exceeded their odor thresholds, which are reported to be 0.022, 0.138 and 11.1 microg/m(3), respectively, at several points within the domain. Their highest concentrations within Gokturk County were estimated to be 0.09387 microg/m(3) for ethyl mercaptan, 0.07934 microg/m(3) for methyl mercaptan and 6.315 microg/m(3) for hydrogen sulfide. Short-term model results revealed the occasional odor problems being reported for Gokturk County. Hourly concentrations were used to obtain frequencies of odor episodes in Gokturk County via a probability analysis. The results showed that ethyl mercaptan concentrations did not exceed its odor threshold during more than 8.84% of the time. Similarly, the maximum odor episode frequencies for methyl mercaptan and hydrogen sulfide were 0.98% and 0.34% of the time, respectively.

  5. HYDROGEN AND VOC RETENTION IN WASTE BOXES

    Energy Technology Data Exchange (ETDEWEB)

    PACE ME; MARUSICH RM

    2008-11-21

    The Hanford Waste Management Project Master Documented Safety Analysis (MDSA) (HNF-14741, 2003) identifies derived safety controls to prevent or mitigate the risks of a single-container deflagration during operations requiring moving, venting or opening transuranic (TRU)-waste containers. The issue is whether these safety controls are necessary for operations involving TRU-waste boxes that are being retrieved from burial at the Hanford Site. This paper investigates the potential for a deflagration hazard within these boxes and whether safety controls identified for drum deflagration hazards should be applied to operations involving these boxes. The study evaluates the accumulation of hydrogen and VOCs within the waste box and the transport of these gases and vapors out of the waste box. To perform the analysis, there were numerous and major assumptions made regarding the generation rate and the transport pathway dimensions and their number. Since there is little actual data with regards to these assumptions, analyses of three potential configurations were performed to obtain some indication of the bounds of the issue (the concentration of hydrogen or flammable VOCs within a waste box). A brief description of each of the three cases along with the results of the analysis is summarized.

  6. Analysis of Sidestream Smoke VOCs and Characterization of their Odor Profiles by VOC Preconcentrator-GC-O Techniques

    Directory of Open Access Journals (Sweden)

    Higashi N

    2014-12-01

    Full Text Available Various techniques have been employed in the analysis of volatile organic compounds (VOCs. However, these techniques are insufficient for the precise analysis of tobacco smoke VOCs because of the complexity of the operating system, system instability, or poor sensitivity. To overcome these problems, a combined system of VOC preconcentrator, gas chromatograph, and olfactometer has been developed. The performance of this new system was evaluated in the analysis of VOCs in tobacco smoke and applied to the odor profiling of sidestream smoke (SSS that has not been sufficiently investigated in the past.

  7. Development and application of a multi-channel monitoring system for near real-time VOC measurement in a hazardous waste management facility.

    Science.gov (United States)

    Je, Chung-hwan; Stone, Richard; Oberg, Steven G

    2007-09-01

    This paper describes the development and application of a multi-channel monitoring system for recording, processing, and analyzing volatile organic compound (VOC) levels discharged to the atmosphere from a walk-in hood in a hazardous waste management facility. The monitoring system consists of an array of PID (photo ionization detector) sensors and a networked control program that provides operational schematic diagram, performs data analyses, and illustrates real-time graphical displays. Furthermore, the system records potential worker exposures, exhaust filtration efficiency and environmental release levels. Multi-channel continuous monitoring of VOCs is successfully implemented during chemical bulking operations. It is shown that a real-time monitoring system is effective for early warning detection of hazardous chemicals and for predicting the performance of adsorption filters used for VOC removal. In addition, a connected local weather visualization system supports efforts to minimize potential health and environmental impacts of VOC emissions to surrounding areas.

  8. The indoor volatile organic compound (VOC) characteristics and source identification in a new university campus in Tianjin, China.

    Science.gov (United States)

    Kang, Jian; Liu, Junjie; Pei, Jingjing

    2017-06-01

    This study investigates the volatile organic compounds (VOCs) constituents and concentration levels on a new university campus, where all of the buildings including classrooms and student dormitories were newly built and decorated within 1 year. Investigated indoor environments include dormitories, classrooms, and the library. About 30 dormitory buildings with different furniture loading ratios were measured. The characteristics of the indoor VOCs species are analyzed and possible sources are identified. The VOCs were analyzed with gas chromatography-mass spectroscopy (GC-MS). It was found that the average total VOC (TVOC) concentration can reach 2.44 mg/m(3). Alkenes were the most abundant VOCs in dormitory rooms, contributing up to 86.5% of the total VOCs concentration. The concentration of α-pinene is the highest among the alkenes. Unlike the dormitory rooms, there is almost no room with TVOC concentration above 0.6 mg/m(3) in classroom and library buildings. Formaldehyde concentration in the dormitory rooms increased about 23.7% after the installation of furniture, and the highest level reached 0.068 mg/m(3). Ammonia released from the building antifreeze material results in an average indoor concentration of 0.28 mg/m(3), which is 100% over the threshold and should be seriously considered. Further experiments were conducted to analyze the source of the α-pinene and some alkanes in dormitory rooms. The results showed that the α-pinene mainly comes from the bed boards, while the wardrobes are the main sources of alkanes. The contribution of the pinewood bed boards to the α-pinene and TVOC concentration can reach up to above 90%. The same type rooms were sampled 1 year later and the decay rate of α-pinene is quite high, close to 100%, so that it almost cannot be detected in the sampled rooms. Analysis of indoor volatile organic compounds (VOCs) in newly built campus buildings in China identified the specific constituents of indoor VOCs contaminants exposed to

  9. Genetic variation in plant volatile emission does not result in differential attraction of natural enemies in the field.

    Science.gov (United States)

    Wason, Elizabeth L; Hunter, Mark D

    2014-02-01

    Volatile organic chemical (VOC) emission by plants may serve as an adaptive plant defense by attracting the natural enemies of herbivores. For plant VOC emission to evolve as an adaptive defense, plants must show genetic variability for the trait. To date, such variability has been investigated primarily in agricultural systems, yet relatively little is known about genetic variation in VOCs emitted by natural populations of native plants. Here, we investigate intraspecific variation in constitutive and herbivore-induced plant VOC emission using the native common milkweed plant (Asclepias syriaca) and its monarch caterpillar herbivore (Danaus plexippus) in complementary field and common garden greenhouse experiments. In addition, we used a common garden field experiment to gauge natural enemy attraction to milkweed VOCs induced by monarch damage. We found evidence of genetic variation in the total constitutive and induced concentrations of VOCs and the composition of VOC blends emitted by milkweed plants. However, all milkweed genotypes responded similarly to induction by monarchs in terms of their relative change in VOC concentration and blend. Natural enemies attacked decoy caterpillars more frequently on damaged than on undamaged milkweed, and natural enemy visitation was associated with higher total VOC concentrations and with VOC blend. Thus, we present evidence that induced VOCs emitted by milkweed may function as a defense against herbivores. However, plant genotypes were equally attractive to natural enemies. Although milkweed genotypes diverge phenotypically in their VOC concentrations and blends, they converge into similar phenotypes with regard to magnitude of induction and enemy attraction.

  10. Volatile organic compounds (VOCs) in photochemically aged air from the eastern and western Mediterranean

    Science.gov (United States)

    Derstroff, Bettina; Hüser, Imke; Bourtsoukidis, Efstratios; Crowley, John N.; Fischer, Horst; Gromov, Sergey; Harder, Hartwig; Janssen, Ruud H. H.; Kesselmeier, Jürgen; Lelieveld, Jos; Mallik, Chinmay; Martinez, Monica; Novelli, Anna; Parchatka, Uwe; Phillips, Gavin J.; Sander, Rolf; Sauvage, Carina; Schuladen, Jan; Stönner, Christof; Tomsche, Laura; Williams, Jonathan

    2017-08-01

    During the summertime CYPHEX campaign (CYprus PHotochemical EXperiment 2014) in the eastern Mediterranean, multiple volatile organic compounds (VOCs) were measured from a 650 m hilltop site in western Cyprus (34° 57' N/32° 23' E). Periodic shifts in the northerly Etesian winds resulted in the site being alternately impacted by photochemically processed emissions from western (Spain, France, Italy) and eastern (Turkey, Greece) Europe. Furthermore, the site was situated within the residual layer/free troposphere during some nights which were characterized by high ozone and low relative humidity levels. In this study we examine the temporal variation of VOCs at the site. The sparse Mediterranean scrub vegetation generated diel cycles in the reactive biogenic hydrocarbon isoprene, from very low values at night to a diurnal median level of 80-100 pptv. In contrast, the oxygenated volatile organic compounds (OVOCs) methanol and acetone exhibited weak diel cycles and were approximately an order of magnitude higher in mixing ratio (ca. 2.5-3 ppbv median level by day, range: ca. 1-8 ppbv) than the locally emitted isoprene and aromatic compounds such as benzene and toluene. Acetic acid was present at mixing ratios between 0.05 and 4 ppbv with a median level of ca. 1.2 ppbv during the daytime. When data points directly affected by the residual layer/free troposphere were excluded, the acid followed a pronounced diel cycle, which was influenced by various local effects including photochemical production and loss, direct emission, dry deposition and scavenging from advecting air in fog banks. The Lagrangian model FLEXPART was used to determine transport patterns and photochemical processing times (between 12 h and several days) of air masses originating from eastern and western Europe. Ozone and many OVOC levels were ˜ 20 and ˜ 30-60 % higher, respectively, in air arriving from the east. Using the FLEXPART calculated transport time, the contribution of photochemical

  11. Volatile organic compounds (VOCs in photochemically aged air from the eastern and western Mediterranean

    Directory of Open Access Journals (Sweden)

    B. Derstroff

    2017-08-01

    Full Text Available During the summertime CYPHEX campaign (CYprus PHotochemical EXperiment 2014 in the eastern Mediterranean, multiple volatile organic compounds (VOCs were measured from a 650 m hilltop site in western Cyprus (34° 57′ N/32° 23′ E. Periodic shifts in the northerly Etesian winds resulted in the site being alternately impacted by photochemically processed emissions from western (Spain, France, Italy and eastern (Turkey, Greece Europe. Furthermore, the site was situated within the residual layer/free troposphere during some nights which were characterized by high ozone and low relative humidity levels. In this study we examine the temporal variation of VOCs at the site. The sparse Mediterranean scrub vegetation generated diel cycles in the reactive biogenic hydrocarbon isoprene, from very low values at night to a diurnal median level of 80–100 pptv. In contrast, the oxygenated volatile organic compounds (OVOCs methanol and acetone exhibited weak diel cycles and were approximately an order of magnitude higher in mixing ratio (ca. 2.5–3 ppbv median level by day, range: ca. 1–8 ppbv than the locally emitted isoprene and aromatic compounds such as benzene and toluene. Acetic acid was present at mixing ratios between 0.05 and 4 ppbv with a median level of ca. 1.2 ppbv during the daytime. When data points directly affected by the residual layer/free troposphere were excluded, the acid followed a pronounced diel cycle, which was influenced by various local effects including photochemical production and loss, direct emission, dry deposition and scavenging from advecting air in fog banks. The Lagrangian model FLEXPART was used to determine transport patterns and photochemical processing times (between 12 h and several days of air masses originating from eastern and western Europe. Ozone and many OVOC levels were  ∼  20 and  ∼  30–60 % higher, respectively, in air arriving from the east. Using the FLEXPART

  12. Atmospheric measurements of ratios between CO2 and co-emitted species from traffic: a tunnel study in the Paris megacity